National Research Council Canada - National Science Library
Vischer, D. L; Hager, Willi H; Hager, W. H
1995-01-01
.... the book comprises chapters in farious fields such as hydraulic jump, stilling basins, ski jumps and plunge pools but introduces also a general account on various methods of dissipation, as well...
Georgious, I. T.; Sun, C. T.
1992-01-01
The history of temperature rise due to internal dissipation of mechanical energy in insulated off-axis uniaxial specimens of the unidirectional thermoplastic composite (AS4/PEEK) has been measured. The experiment reveals that the rate of temperature rise is a polynomial function of stress amplitude: It consists of a quadratic term and a sixth power term. This fact implies that the specific heat of the composite depends on the stretching its microstructure undergoes during deformation. The Einstein theory for specific heat is used to explain the dependence of the specific heat on the stretching of the microstructure.
An estimate of energy dissipation due to soil-moisture hysteresis
McNamara, H.
2014-01-01
Processes of infiltration, transport, and outflow in unsaturated soil necessarily involve the dissipation of energy through various processes. Accounting for these energetic processes can contribute to modeling hydrological and ecological systems. The well-documented hysteretic relationship between matric potential and moisture content in soil suggests that one such mechanism of energy dissipation is associated with the cycling between wetting and drying processes, but it is challenging to estimate the magnitude of the effect in situ. The Preisach model, a generalization of the Independent Domain model, allows hysteresis effects to be incorporated into dynamical systems of differential equations. Building on earlier work using such systems with field data from the south-west of Ireland, this work estimates the average rate of hysteretic energy dissipation. Through some straightforward assumptions, the magnitude of this rate is found to be of O(10-5) W m-3. Key Points Hysteresis in soil-water dissipates energy The rate of dissipation can be estimated directly from saturation data The rate of heating caused is significant ©2013. American Geophysical Union. All Rights Reserved.
2002-01-01
The moon's gravity imparts tremendous energy to the Earth, raising tides throughout the global oceans. What happens to all this energy? This question has been pondered by scientists for over 200 years, and has consequences ranging from the history of the moon to the mixing of the oceans. Richard Ray at NASA's Goddard Space Flight Center, Greenbelt, Md. and Gary Egbert of the College of Oceanic and Atmospheric Sciences, Oregon State University, Corvallis, Ore. studied six years of altimeter data from the TOPEX/Poseidon satellite to address this question. According to their report in the June 15 issue of Nature, about 1 terawatt, or 25 to 30 percent of the total tidal energy dissipation, occurs in the deep ocean. The remainder occurs in shallow seas, such as on the Patagonian Shelf. 'By measuring sea level with the TOPEX/Poseidon satellite altimeter, our knowledge of the tides in the global ocean has been remarkably improved,' said Richard Ray, a geophysicist at Goddard. The accuracies are now so high that this data can be used to map empirically the tidal energy dissipation. (Red areas, above) The deep-water tidal dissipation occurs generally near rugged bottom topography (seamounts and mid-ocean ridges). 'The observed pattern of deep-ocean dissipation is consistent with topographic scattering of tidal energy into internal motions within the water column, resulting in localized turbulence and mixing', said Gary Egbert an associate professor at OSU. One important implication of this finding concerns the possible energy sources needed to maintain the ocean's large-scale 'conveyor-belt' circulation and to mix upper ocean heat into the abyssal depths. It is thought that 2 terawatts are required for this process. The winds supply about 1 terawatt, and there has been speculation that the tides, by pumping energy into vertical water motions, supply the remainder. However, all current general circulation models of the oceans ignore the tides. 'It is possible that properly
Energy dissipation in biomolecular machines
Energy Technology Data Exchange (ETDEWEB)
Lervik, Anders
2012-07-01
thermodynamic efficiency is found to be low (< 13 %) in all cases for the experimental conditions considered, which means that a large amount of the energy released from the ATP-hydrolysis is dissipated as heat. A complementary molecular dynamics study targeted on a bilayer for which the protein shows a relatively large efficiency (compared to other bilayers) shows that membrane deformation and large efficiency are not mutually exclusive. Overall, this thesis highlights the usefulness of the mesoscopic non-equilibrium thermodynamic framework applied to molecular machines and energy transduction and dissipation in these. The main result is that the mesoscopic nonequilibrium thermodynamic framework is applicable to molecular pumps and can be extended to include heat effects. This framework is general and can be applied to other molecular machines as well. Further, the results also support the notion that the calcium pump may contribute to non-shivering thermogenesis in certain tissues.(Author)
Material Systems for Blast-Energy Dissipation
Energy Technology Data Exchange (ETDEWEB)
James Schondel; Henry S. Chu
2010-10-01
Lightweight panels have been designed to protect buildings and vehicles from blast pressures by activating energy dissipation mechanisms under the influence of blast loading. Panels were fabricated which featured a variety of granular materials and hydraulic dissipative deformation mechanisms and the test articles were subjected to full-scale blast loading. The force time-histories transmitted by each technology were measured by a novel method that utilized inexpensive custom-designed force sensors. The array of tests revealed that granular materials can effectively dissipate blast energy if they are employed in a way that they easily crush and rearrange. Similarly, hydraulic dissipation can effectively dissipate energy if the panel features a high fraction of porosity and the panel encasement features low compressive stiffness.
Energy dissipation mapping of cancer cells.
Dutta, Diganta; Palmer, Xavier-Lewis; Kim, Jinhyun; Qian, Shizhi; Stacey, Michael
2018-02-01
The purpose of this study is to map the energy dissipation of Jurkat cells using a single 60 nanosecond pulse electric field (NsPEF), primarily through atomic force microscopy (AFM). The phase shift is generated by the sample elements that do not have a heterogeneous surface. Monitoring and manipulating the phase shift is a powerful way for determining the dissipated energy and plotting the topography. The dissipated energy is a relative value, so the silica wafer and cover slip are given a set reference while the transmission of energy between the tip of the cantilever and cell surfaces is measured. The most important finding is that the magnitude and the number of variations in the dissipated energy change with the strength of NsPEF applied. Utilizing a single low field strength NsPEF (15kV/cm), minor changes in dissipated energy were found. The application of a single high field strength NsPEF (60kV/cm) to Jurkat cells resulted in a higher dissipated energy change versus that of in the low field strength condition. Thus, the dissipated energy from the Jurkat cells changes with the strength of NsPEF. By analyzing the forces via investigation in the tapping mode of the AFM, the stabilization of the cytoskeleton and membrane of the cell are related to the strength of NsPEF applied. Furthermore, the strength of NsPEF indicates a meaningful relationship to the survival of the Jurkat cells. Copyright © 2017 Elsevier Ltd. All rights reserved.
Mechanical energy dissipation in natural ceramic composites.
Mayer, George
2017-12-01
Ceramics and glasses, in their monolithic forms, typically exhibit low fracture toughness values, but rigid natural marine ceramic and glass composites have shown remarkable resistance to mechanical failure. This has been observed in load-extension behavior by recognizing that the total area under the curve, notably the part beyond the yield point, often conveys substantial capacity to carry mechanical load. The mechanisms underlying the latter observations are proposed as defining factors for toughness that provide resistance to failure, or capability to dissipate energy, rather than fracture toughness. Such behavior is exhibited in the spicules of glass sponges and in mollusk shells. There are a number of similarities in the manner in which energy dissipation takes place in both sponges and mollusks. It was observed that crack diversion, a new form of crack bridging, creation of new surface area, and other important energy-dissipating mechanisms occur and aid in "toughening". Crack tolerance, key to energy dissipation in these natural composite materials, is assisted by promoting energy distribution over large volumes of loaded specimens by minor components of organic constituents that also serve important roles as adhesives. Viscoelastic deformation was a notable characteristic of the organic component. Some of these energy-dissipating modes and characteristics were found to be quite different from the toughening mechanisms that are utilized for more conventional structural composites. Complementary to those mechanisms found in rigid natural ceramic/organic composites, layered architectures and very thin organic layers played major roles in energy dissipation in these structures. It has been demonstrated in rigid natural marine composites that not only architecture, but also the mechanical behavior of the individual constituents, the nature of the interfaces, and interfacial bonding play important roles in energy dissipation. Additionally, the controlling
Energy and dissipated work in snow avalanches
Bartelt, P.; Buser, O.
2004-12-01
Using the results of large scale avalanche experiments at the Swiss Vallée de la Sionne test site, the energy balance of several snow avalanches is determined. Avalanches convert approximately one-seventh of their potential energy into kinetic energy. The total potential energy depends strongly on the entrained snowcover, indicating that entrainment processes cannot be ignored when predicting terminal velocities and runout distances. We find energy dissipation rates on the order of 1 GW. Fluidization of the fracture slab can be identified in the experiments as an increase in dissipation rate, thereby explaining the initial and rapid acceleration of avalanches after release. Interestingly, the dissipation rates appear to be constant along the track, although large fluctuations in internal velocity exist. Thus, we can demonstrate within the context of non-equilibrium thermodynamics that -- in space -- granular snow avalanches are irreversible, dissipative systems that minimize entropy production because they appear to reach a steady-state non-equilibrium. A thermodynamic analysis reveals that fluctuations in velocity depend on the roughness of the flow surface and viscosity of the granular system. We speculate that this property explains the transition from flowing avalanches to powder avalanches.
Tidal Energy Dissipation from Topex/Poseidon
Ray, Richard D.; Egbert, G. D.; Smith, David E. (Technical Monitor)
2000-01-01
In a recent paper ({\\it Nature, 405,} 775, 2000) we concluded that 25 to 30\\% of the ocean's tidal energy dissipation, or about 1 terawatt, occurs in the deep ocean, with the remaining 2.6 TW in shallow seas. The physical mechanism for deep-ocean dissipation is apparently scattering of the surface tide into internal modes; Munk and Wunsch have suggested that this mechanism may provide half the power needed for mixing the deep-ocean. This paper builds further evidence for $1\\pm 0.2$ TW of deep-ocean dissipation. The evidence is extracted from tidal elevations deduced from seven years of Topex/Poseidon satellite altimeter data. The dissipation rate Is formed as a balance between the rate of working by tidal forces and the energy flux divergence. While dynamical assumptions are required to compute fluxes, area integrals of the energy balance are, owing to the tight satellite constraints, remarkably insensitive to these assumptions. A large suite of tidal solutions based on a wide range of dynamical assumptions, on perturbations to bathymetric models, and on simulated elevation data are used to assess this sensitivity. These and Monte Carlo error fields from a generalized inverse model are used to establish error uncertainties.
estimation of ionospheric energy dissipation for the year 2012 using
African Journals Online (AJOL)
userpc
both mean daily and hourly ionospheric energy dissipation using Østgaard's empirical relation. The computation has been ... energy dissipation is the dominant channel of energy transfer in that year from the solar wind. This is consistent with many ..... converted to thermal energy for dissipation in the ionosphere (Kallio, et ...
Assessing relative volatility/intermittency/energy dissipation
DEFF Research Database (Denmark)
Barndorff-Nielsen, Ole E.; Pakkanen, Mikko S.; Schmiegel, Jürgen
2014-01-01
process in particular. This estimation method is motivated by the assessment of relative energy dissipation in empirical data of turbulence, but it is also applicable in other areas. We develop a probabilistic asymptotic theory for realised relative power variations of Brownian semistationary processes......, and introduce inference methods based on the theory. We also discuss how to extend the asymptotic theory to other classes of processes exhibiting stochastic volatility/intermittency. As an empirical application, we study relative energy dissipation in data of atmospheric turbulence.......We introduce the notion of relative volatility/intermittency and demonstrate how relative volatility statistics can be used to estimate consistently the temporal variation of volatility/intermittency when the data of interest are generated by a non-semimartingale, or a Brownian semistationary...
Low Energy Dissipation Nano Device Research
Yu, Jenny
2015-03-01
The development of research on energy dissipation has been rapid in energy efficient area. Nano-material power FET is operated as an RF power amplifier, the transport is ballistic, noise is limited and power dissipation is minimized. The goal is Green-save energy by developing the Graphene and carbon nantube microwave and high performance devices. Higher performing RF amplifiers can have multiple impacts on broadly field, for example communication equipment, (such as mobile phone and RADAR); higher power density and lower power dissipation will improve spectral efficiency which translates into higher system level bandwidth and capacity for communications equipment. Thus, fundamental studies of power handling capabilities of new RF (nano)technologies can have broad, sweeping impact. Because it is critical to maximizing the power handling ability of grephene and carbon nanotube FET, the initial task focuses on measuring and understanding the mechanism of electrical breakdown. We aim specifically to determine how the breakdown voltage in graphene and nanotubes is related to the source-drain spacing, electrode material and thickness, and substrate, and thus develop reliable statistics on the breakdown mechanism and probability.
Assessing Relative Volatility/Intermittency/Energy Dissipation
DEFF Research Database (Denmark)
Barndorff-Nielsen, Ole E.; Pakkanen, Mikko; Schmiegel, Jürgen
process in particular. While this estimation method is motivated by the assessment of relative energy dissipation in empirical data of turbulence, we apply it also to energy price data. Moreover, we develop a probabilistic asymptotic theory for relative power variations of Brownian semistationary......We introduce the notion of relative volatility/intermittency and demonstrate how relative volatility statistics can be used to estimate consistently the temporal variation of volatility/intermittency even when the data of interest are generated by a non-semimartingale, or a Brownian semistationary...... processes and Ito semimartingales and discuss how it can be used for inference on relative volatility/intermittency....
Wind Turbine Control with Active Damage Reduction through Energy Dissipation
Barradas Berglind, Jose de Jesus; Jayawardhana, Bayu; Wisniewski, Rafał
2016-01-01
In this paper we propose an active damage reduction control strategy for wind turbines based on dissipated energy. To this end we rely on the equivalences relating both damage in the rainflow counting sense and dissipated energy to the variations of Preisach hysteresis operators. Since dissipation
Offshore heat dissipation for nuclear energy centers
International Nuclear Information System (INIS)
Bauman, H.F.
1978-09-01
The technical, environmental, and economic aspects of utilizing the ocean or other large water bodies for the dissipation of reject heat from Nuclear Energy Centers (NECs) were investigated. An NEC in concept is an aggregate of nuclear power plants of 10 GW(e) capacity or greater on a common site. The use of once-through cooling for large power installations offers advantages including higher thermal efficiencies, especially under summer peak-load conditions, compared to closed-cycle cooling systems. A disadvantage of once-through cooling is the potential for greater adverse impacts on the aquatic environment. A concept is presented for minimizing the impacts of such systems by placing water intake and discharge locations relatively distant from shore in deeper water than has heretofore been the practice. This technique would avoid impacts on relatively biologically productive and ecologically sensitive shallow inshore areas. The NEC itself would be set back from the shoreline so that recreational use of the shore area would not be impaired. The characteristics of a heat-dissipation system of the size required for a NEC were predicted from the known characteristics of a smaller system by applying hydraulic scaling laws. The results showed that adequate heat dissipation can be obtained from NEC-sized systems located in water of appropriate depth. Offshore intake and discharge structures would be connected to the NEC pump house on shore via tunnels or buried pipelines. Tunnels have the advantage that shoreline and beach areas would not be disturbed. The cost of an offshore heat-dissipation system depends on the characteristics of the site, particularly the distance to suitably deep water and the type of soil or rock in which water conduits would be constructed. For a favorable site, the cost of an offshore system is estimated to be less than the cost of a closed-cycle system
Dissipation and energy balance in electronic dynamics of Na clusters
Vincendon, Marc; Suraud, Eric; Reinhard, Paul-Gerhard
2017-06-01
We investigate the impact of dissipation on the energy balance in the electron dynamics of metal clusters excited by strong electro-magnetic pulses. The dynamics is described theoretically by Time-Dependent Density-Functional Theory (TDDFT) at the level of Local Density Approximation (LDA) augmented by a self interaction correction term and a quantum collision term in Relaxation-Time Approximation (RTA). We evaluate the separate contributions to the total excitation energy, namely energy exported by electron emission, potential energy due to changing charge state, intrinsic kinetic and potential energy, and collective flow energy. The balance of these energies is studied as function of the laser parameters (frequency, intensity, pulse length) and as function of system size and charge. We also look at collisions with a highly charged ion and here at the dependence on the impact parameter (close versus distant collisions). Dissipation turns out to be small where direct electron emission prevails namely for laser frequencies above any ionization threshold and for slow electron extraction in distant collisions. Dissipation is large for fast collisions and at low laser frequencies, particularly at resonances. Contribution to the Topical Issue "Dynamics of Systems at the Nanoscale", edited by Andrey Solov'yov and Andrei Korol.
Intrinsic Energy Dissipation Limits in Nano and Micromechanical Resonators
Iyer, Srikanth Subramanian
Resonant microelectromechanical Systems (MEMS) have enabled miniaturization of high-performance inertial sensors, radio-frequency filters, timing references and mass-based chemical sensors. Despite the increasing prevalence of MEMS resonators for these applications, the energy dissipation in these structures is not well-understood. Accurate prediction of the energy loss and the resulting quality factor (Q) has significant design implications because it is directly related to device performance metrics including sensitivity for resonant sensors, bandwidth for radio-frequency filters and phase-noise for timing references. In order to assess the future potential for MEMS resonators it is critically important to evaluate the energy dissipation limits, which will dictate the ultimate performance resonant MEMS devices can achieve. This work focuses on the derivation and evaluation of the intrinsic mechanical energy dissipation limit for single-crystal nano and micromechanical resonators due to anharmonic phonon-phonon scattering in the Akhiezer regime. The energy loss is derived using perturbation theory and the linearized Boltzmann transport equation for phonons, and includes the direction and polarization dependent mode-Gruneisen parameters in order to capture the strain-induced anharmonicity among phonon branches. Evaluation of the quality factor limit reveals that Akhiezer damping, previously thought to depend only on material properties, has a strong dependence on crystal orientation and resonant mode shape. The robust model provides a dissipation limit for all resonant modes including shear-mode vibrations, which have significantly reduced energy loss because dissipative phonon-phonon scattering is restricted to volume-preserving phonon branches, indicating that Lame or wine-glass mode resonators will have the highest upper limit on mechanical efficiency. Finally, the analytical dissipation model is integrated with commercial finite element software in order to
Meteorological effects of energy dissipation at large power parks
International Nuclear Information System (INIS)
Hanna, S.R.; Gifford, F.A.
1976-01-01
Large (10,000 to 50,000 MW) power parks are being studied as one means of satisfying the nation's demand for energy. The dissipation of waste energy from these installations may result in significant meteorological effects. It is shown that the rate of atmospheric dissipation of the waste energy from these power parks is approximately equal to the atmospheric dissipation of energy by geophysical phenomena such as thunderstorms, volcanoes, and large bushfires. Cumulus clouds and whirlwinds often result from these energy releases. There is a possibility that natural vorticity will be concentrated by large power parks. A theory of multiple plume rise is used to estimate the enhancement of plume rise from multiple cooling towers. Calculations of plume rise, ground level fog intensity, and drift deposition due to emissions from cooling towers at a hypothetical 40,000 MW nuclear power park are made. The plume rise from 50 towers is estimated to be more than 110 percent of that from a single tower if the tower spacing is less than about 300 m
Energy dissipation of rockfalls by coppice structures
Directory of Open Access Journals (Sweden)
G. Ciabocco
2009-06-01
Full Text Available The objective of this work is to develop elements to improve understanding of the behaviour of a coppice in relation to the phenomenon of falling boulders. The first section proposes an amendment to the equation for calculating the index which describes the probability of impact between a rock and plants in managed coppice forests. A study was carried out, using models to calculate the kinetic energy of a falling boulder along a slope considering the kinetic energy dissipated during the impact with the structure of forest plants managed by coppice. The output of the simulation models were then compared with the real dynamics of falling boulders in field tests using digital video.
It emerged from an analysis of the results of this comparison that a modification to the 1989 Gsteiger equation was required, in order to calculate the "Average Distance between Contacts" (ADC. To this purpose, the concept of "Structure of Interception", proposed in this paper, was developed, valid as a first approach for describing the differences in the spatial distribution of stems between coppice and forest. This study also aims to provide suggestions for forestry management, in order to maintain or increase the protective capacity of a coppice managed with conventional techniques for the area studied, modifying the dendrometric characteristics.
Thermal energy dissipation and xanthophyll cycles beyond the Arabidopsis model.
García-Plazaola, José Ignacio; Esteban, Raquel; Fernández-Marín, Beatriz; Kranner, Ilse; Porcar-Castell, Albert
2012-09-01
Thermal dissipation of excitation energy is a fundamental photoprotection mechanism in plants. Thermal energy dissipation is frequently estimated using the quenching of the chlorophyll fluorescence signal, termed non-photochemical quenching. Over the last two decades, great progress has been made in the understanding of the mechanism of thermal energy dissipation through the use of a few model plants, mainly Arabidopsis. Nonetheless, an emerging number of studies suggest that this model represents only one strategy among several different solutions for the environmental adjustment of thermal energy dissipation that have evolved among photosynthetic organisms in the course of evolution. In this review, a detailed analysis of three examples highlights the need to use models other than Arabidopsis: first, overwintering evergreens that develop a sustained form of thermal energy dissipation; second, desiccation tolerant plants that induce rapid thermal energy dissipation; and third, understorey plants in which a complementary lutein epoxide cycle modulates thermal energy dissipation. The three examples have in common a shift from a photosynthetically efficient state to a dissipative conformation, a strategy widely distributed among stress-tolerant evergreen perennials. Likewise, they show a distinct operation of the xanthophyll cycle. Expanding the list of model species beyond Arabidopsis will enhance our knowledge of these mechanisms and increase the synergy of the current studies now dispersed over a wide number of species.
Energy-dissipation-model for metallurgical multi-phase-systems
Energy Technology Data Exchange (ETDEWEB)
Mavrommatis, K.T. [Rheinisch-Westfaelische Technische Hochschule Aachen, Aachen (Germany)
1996-12-31
Entropy production in real processes is directly associated with the dissipation of energy. Both are potential measures for the proceed of irreversible processes taking place in metallurgical systems. Many of these processes in multi-phase-systems could then be modelled on the basis of the energy-dissipation associated with. As this entity can often be estimated using very simple assumptions from first principles, the evolution of an overall measure of systems behaviour can be studied constructing an energy-dissipation -based model of the system. In this work a formulation of this concept, the Energy-Dissipation-Model (EDM), for metallurgical multi-phase-systems is given. Special examples are studied to illustrate the concept, and benefits as well as the range of validity are shown. This concept might be understood as complement to usual CFD-modelling of complex systems on a more abstract level but reproducing essential attributes of complex metallurgical systems. (author)
Estimation of ionospheric energy dissipation for the year 2012 using ...
African Journals Online (AJOL)
In this paper, data for the electron precipitation energy(ep) and joule heating energy(jh) have been used in the computation of both mean daily and hourly ionospheric ... with 90% confidence level, which indicates that ionospheric energy dissipation is the dominant channel of energy transfer in that year from the solar wind.
Dissipative generalized Chaplygin gas as phantom dark energy
International Nuclear Information System (INIS)
Cruz, Norman; Lepe, Samuel; Pena, Francisco
2007-01-01
The generalized Chaplygin gas, characterized by the equation of state p=-A/ρ α , has been considered as a model for dark energy due to its dark-energy-like evolution at late times. When dissipative processes are taken into account, within the framework of the standard Eckart theory of relativistic irreversible thermodynamics, cosmological analytical solutions are found. Using the truncated causal version of the Israel-Stewart formalism, a suitable model was constructed which crosses the w=-1 barrier. The future-singularities encountered in both approaches are of a new type, and not included in the classification presented by Nojiri and Odintsov [S. Nojiri, S.D. Odintsov, Phys. Rev. D 72 (2005) 023003
Dissipative generalized Chaplygin gas as phantom dark energy
Energy Technology Data Exchange (ETDEWEB)
Cruz, Norman [Departamento de Fisica, Facultad de Ciencia, Universidad de Santiago, Casilla 307, Santiago (Chile)]. E-mail: ncruz@lauca.usach.cl; Lepe, Samuel [Instituto de Fisica, Facultad de Ciencias Basicas y Matematicas, Pontificia Universidad Catolica de Valparaiso, Avenida Brasil 2950, Valparaiso (Chile)]. E-mail: slepe@ucv.cl; Pena, Francisco [Departamento de Ciencias Fisicas, Facultad de Ingenieria, Ciencias y Administracion, Universidad de la Frontera, Avda. Francisco Salazar 01145, Casilla 54-D, Temuco (Chile)]. E-mail: fcampos@ufro.cl
2007-03-15
The generalized Chaplygin gas, characterized by the equation of state p=-A/{rho}{sup {alpha}}, has been considered as a model for dark energy due to its dark-energy-like evolution at late times. When dissipative processes are taken into account, within the framework of the standard Eckart theory of relativistic irreversible thermodynamics, cosmological analytical solutions are found. Using the truncated causal version of the Israel-Stewart formalism, a suitable model was constructed which crosses the w=-1 barrier. The future-singularities encountered in both approaches are of a new type, and not included in the classification presented by Nojiri and Odintsov [S. Nojiri, S.D. Odintsov, Phys. Rev. D 72 (2005) 023003].
Observations of turbulent energy dissipation rate in the upper ocean of the central South China Sea
Chen, G.
2016-02-01
Measurements of turbulent energy dissipation rate, velocity, temperature, and salinity were obtained in the upper ocean of the central South China Sea (14.5˚N, 117.0˚E) during an experimental campaign from May 11th to 13th 2010. Dissipation rate was elevated ( 10-7 Wkg-1) at night by convection mixing and was weakened ( 10-9 Wkg-1) in daytime due to the warming stratification. Thermocline dissipation rate varied with time ( 10-9 Wkg-1 to 10-8 Wkg-1) under the influence of internal waves. Energy was transferred from the diurnal internal tides to high frequency internal waves through nonlinear wave-wave interactions. This energy cascade process was accompanied by elevated shear and enhanced dissipation, which played an important role in the turbulent mixing in thermocline. Compare with the thermocline dissipation, dissipation below the thermocline was more stable and weak ( 10-10 Wkg-1). The observed dissipation rate during the measurement was well parameterized by the MacKinnon-Gregg parameterization (a model based on a reinterpretation of wave-wave interaction theory), whereas the Gregg-Henyey parameterization was not in good agreement with the observed dissipation rate.
Beam-to-Column Connections with Demountable Energy Dissipative Plates
Directory of Open Access Journals (Sweden)
Vasile-Mircea Venghiac
2018-03-01
Full Text Available The behavior of steel structures subjected to seismic actions depends directly on the connections behavior. There are two current tendencies for ensuring the structural ductility: allowing the formation of plastic hinges in the beams by using reduced beam sections or reduced web sections or by ensuring the plastic hinge formation in the connection by using dissipative elements. This paper presents a new perspective regarding the energy dissipation mechanism formation within the beam-to-column connection. The design of connections capable of dissipating large amounts of energy, with an acceptable strength and ductile behavior is a real challenge for engineers. Sustainability is a big advantage for these connections. Another big advantage is the possibility of restoring the functionality of the damaged construction in a short time interval and with reduced costs. The introduction of connections with demountable energy dissipative plates can be a step forward in designing new beam-to-column connections for steel structures.
Numerical simulation of energy equation with viscous dissipation for compressible flow over cones
International Nuclear Information System (INIS)
Asif, M.; Chughtai, I.R.
1998-01-01
A finite volume discretization technique has been used to solve the energy equation with viscous dissipation. The effects of viscous heat dissipation for Mach numbers 1.5 and 2.0, at an angle of attack of 0 degree, over sharp and blunt cones have been studied. Algebraic equations have been solved using line-by-line Tda method. Supersonic flow over cones has been analyzed and discussed with and without considering the viscous dissipation effects. It has been found that the effects of viscous dissipation increase with the increase in Mach number. Viscous dissipation affects the temperature distribution of the body. However, the temperature difference in these cases was insignificant. This may be due to the fact that these analysis have been done at 0 km altitude. (author)
Architected squirt-flow materials for energy dissipation
Cohen, Tal; Kurzeja, Patrick; Bertoldi, Katia
2017-12-01
In the present study we explore material architectures that lead to enhanced dissipation properties by taking advantage of squirt-flow - a local flow mechanism triggered by heterogeneities at the pore level. While squirt-flow is a known dominant source of dissipation and seismic attenuation in fluid saturated geological materials, we study its untapped potential to be incorporated in highly deformable elastic materials with embedded fluid-filled cavities for future engineering applications. An analytical investigation, that isolates the squirt-flow mechanism from other potential dissipation mechanisms and considers an idealized setting, predicts high theoretical levels of dissipation achievable by squirt-flow and establishes a set of guidelines for optimal dissipation design. Particular architectures are then investigated via numerical simulations showing that a careful design of the internal voids can lead to an increase of dissipation levels by an order of magnitude, compared with equivalent homogeneous void distributions. Therefore, we suggest squirt-flow as a promising mechanism to be incorporated in future architected materials to effectively and reversibly dissipate energy.
Penetration of an electron beam into material and energy dissipation
International Nuclear Information System (INIS)
Kral, V.; Pelzbauer, Z.
1986-01-01
The contribution is concerned with penetration of an electron beam having energy between 5 and 25 keV into the polymer and with energy dissipation inside the interaction volume of the polymer. The experimentally observed shape on the interaction volume has been theoretically substantiated, the range has been calculated, and a comparison with Gruen's empirical relation has been carried out. It is shown that with increasing accelerating voltage the centre of the core of the interaction volume is shifted more deeply under the sample surface and the dissipated energy decreases. Extension of the neck of the interaction volume caused by back scattering is discussed. (author)
Energy Dissipation Rate in an Agitated Crucible Containing Molten Metal
Li, Tao; Shimasaki, Shin-ichi; Narita, Shunsuke; Taniguchi, Shoji
2017-10-01
The energy dissipation rate (EDR) is an important parameter for characterizing the behavior of inclusion coagulation in agitated molten metal. To clarify the inclusion coagulation mechanism, we review previous water model studies by particularly focusing on the relation between the impeller torque and the EDR of the fluid, which indicates the ratio of energy dissipated in the viscous medium to the energy inputted by the rotating impeller. In the present study, simulations coupled with experiments were performed to determine the relation between the torque and the effective EDR for water and liquid Al in crucibles with and without baffles.
Observations of the turbulent kinetic energy dissipation rate in the upper central South China Sea
Liang, Chang-Rong; Chen, Gui-Ying; Shang, Xiao-Dong
2017-05-01
Measurements of the turbulent kinetic energy dissipation rate ( ɛ), velocity, temperature, and salinity were obtained for the upper ocean of the central South China Sea (14.5° N, 117.0° E) during an experimental campaign from May 11 to 13, 2010. Dissipation in the diurnal mixed layer showed a diurnal variability that was strongly affected by the surface buoyancy flux. Dissipation was enhanced ( ɛ ˜ 10-7 W kg-1) at night due to the convective mixing and was weakened ( ɛ ˜ 10-9 W kg-1) in daytime due to the stratification. Dissipation in the thermocline varied with time under the influence of internal waves. Shear from high-frequency internal waves (period ˜8 h) played an important role in enhancing the turbulent mixing in the thermocline. In the period of strong high-frequency internal waves, the shear from high-frequency internal waves became strong and the depth-averaged ɛ in the thermocline was elevated by almost one order of magnitude. Compared with the dissipation in the thermocline, dissipation below was weaker (the time-averaged ɛ ˜ 10-10 W kg-1). The observation indicates that the dissipation rates during the measurements can be parameterized by the MacKinnon-Gregg model that is widely used in the continental shelf but are not in agreement with the Gregg-Henyey model used for the open ocean.
Turbulent energy dissipation in coronal loops: statistical analysis of dissipative structures
Gomez, D. O.; Morales, L. F.; Dmitruk, P.
2017-12-01
The power law energy distribution observed in dissipation events ranging from flares down to nanoflares, has been associated either to intermittent turbulence or to self-organized criticality. In spite of the many studies conducted in recent years, it is unclear whether these two paradigms are mutually exclusive or whether they are complementary manifestations of the complexity of the system.We numericaly integrate the magnetohydrodynamic equations to simulate the dynamics of coronal loops driven at their bases by footpoint motions. After a few photospheric turnover times, a stationary turbulent regime is reached, displaying a broadband power spectrum and a dissipation rate consistent with the cooling rates of the plasma confined in these loops. Our main goal is to determine whether the intermittent features observed in this turbulent flow can also be regarded as manifestations of self-organized criticality. A statistical analysis of the energy, area and lifetime of the dissipative structures observed in these simulations display robust scaling laws.In a preliminary study, we calculated the critical exponents characterizing the avalanche dynamics, andthe spreading exponents that quantify the growth of these structures over time. In this work we also calculate the remaining critical exponents for several activity thresholds and verify that they satisfy the conservation relations predicted for SOC systems. These results can therefore be regarded as a bona fide test supporting that the stationary turbulent regimes characterizing coronal loops, also correspond to states of self organized cricality.
Energy dissipation by a longitudinal Raman process
International Nuclear Information System (INIS)
Fano, U.; Inokuti, Mitio
1994-01-01
The concept of a longitudinal Raman process is introduced to encompass the indirect transmission of energy from slow electrons to nuclei through the reversible polarization of surrounding electrons. Experimental approaches are sought to assess this process quantitatively
Energy Dissipation in Sandwich Structures During Axial Compression
DEFF Research Database (Denmark)
Urban, Jesper
2002-01-01
-scale structural elements in fast sandwich vessels. Two of the crushing tests are simulated with the explicit finite element software LS-DYNA3D. The key results are load-end shortening relationship and the energy dissipation. Good agreement between the numerical predictions and the experiments are obtained...
ENERGY DISSIPATION IN MAGNETIC NULL POINTS AT KINETIC SCALES
International Nuclear Information System (INIS)
Olshevsky, Vyacheslav; Lapenta, Giovanni; Divin, Andrey; Eriksson, Elin; Markidis, Stefano
2015-01-01
We use kinetic particle-in-cell and MHD simulations supported by an observational data set to investigate magnetic reconnection in clusters of null points in space plasma. The magnetic configuration under investigation is driven by fast adiabatic flux rope compression that dissipates almost half of the initial magnetic field energy. In this phase powerful currents are excited producing secondary instabilities, and the system is brought into a state of “intermittent turbulence” within a few ion gyro-periods. Reconnection events are distributed all over the simulation domain and energy dissipation is rather volume-filling. Numerous spiral null points interconnected via their spines form null lines embedded into magnetic flux ropes; null point pairs demonstrate the signatures of torsional spine reconnection. However, energy dissipation mainly happens in the shear layers formed by adjacent flux ropes with oppositely directed currents. In these regions radial null pairs are spontaneously emerging and vanishing, associated with electron streams and small-scale current sheets. The number of spiral nulls in the simulation outweighs the number of radial nulls by a factor of 5–10, in accordance with Cluster observations in the Earth's magnetosheath. Twisted magnetic fields with embedded spiral null points might indicate the regions of major energy dissipation for future space missions such as the Magnetospheric Multiscale Mission
Reduction in energy dissipation rate with increased effective applied field
Czech Academy of Sciences Publication Activity Database
Janů, Zdeněk; Soukup, František
2015-01-01
Roč. 28, č. 8 (2015), "085016-1"-"085016-5" ISSN 0953-2048 Institutional support: RVO:68378271 Keywords : critical state * hysteresis * energy dissipation rate * field waveform Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.717, year: 2015
thermoelastic waves without energy dissipation in an elastic plate ...
African Journals Online (AJOL)
cistvr
tensor has only two components rr σ and. ϑϑ σ which are the normal stresses in the radial and transverse directions respectively. According to the theory of thermoelasticity without energy dissipation, the field equations for a homogeneous and isotropic thermoelastic body, in the absence of heat sources and body forces, ...
Thermoelastic waves without energy dissipation in an elastic plate to ...
African Journals Online (AJOL)
The linear theory of thermoelasticity without energy dissipation for isotropic and homogeneous materials is employed to study waves in an elastic plate. The waves are assumed to arise out of a ramp-type stress on the plate's boundary which is maintained at constant temperature. Laplace transforms are used to solve the ...
Study of Intrinsic Dissipation Due to Thermoelastic Coupling in Gyroscope Resonators.
Li, Changlong; Gao, Shiqiao; Niu, Shaohua; Liu, Haipeng
2016-09-07
This paper presents analytical models, as well as numerical and experimental verification of intrinsic dissipation due to thermoelastic loss in tuning-fork resonator. The thermoelastic analytical governing equations are created for resonator vibrating at drive-mode and sense-mode, and thermoelastic vibration field quantities are deduced. Moreover, the theoretical values are verified that coincided well with finite element analysis (FEM) simulation results. Also, the comparison of vibration field quantities is made to investigate the effect of different conditions on resonator thermoelastic vibration behavior. The significant parameters of thermoelastic damping and quality factor are subsequently deduced to analyze the energy dissipation situation in the vibration process. Meanwhile, the corresponding conclusions from other studies are used to verify our theoretical model and numerical results. By comparing with the experimental quality factor, the numerical values are validated. The combination of the theoretical expressions, numerical results and experimental data leads to an important insight into the achievable quality factor value of tuning-fork resonator, namely, that the thermoelastic damping is the main loss mechanism in the micro-comb finger structure and the quality factor varies under different vibration modes. The results demonstrate that the critical geometry dimensions of tuning-fork resonator can be well designed with the assistance of this study.
Study of Intrinsic Dissipation Due to Thermoelastic Coupling in Gyroscope Resonators
Directory of Open Access Journals (Sweden)
Changlong Li
2016-09-01
Full Text Available This paper presents analytical models, as well as numerical and experimental verification of intrinsic dissipation due to thermoelastic loss in tuning-fork resonator. The thermoelastic analytical governing equations are created for resonator vibrating at drive-mode and sense-mode, and thermoelastic vibration field quantities are deduced. Moreover, the theoretical values are verified that coincided well with finite element analysis (FEM simulation results. Also, the comparison of vibration field quantities is made to investigate the effect of different conditions on resonator thermoelastic vibration behavior. The significant parameters of thermoelastic damping and quality factor are subsequently deduced to analyze the energy dissipation situation in the vibration process. Meanwhile, the corresponding conclusions from other studies are used to verify our theoretical model and numerical results. By comparing with the experimental quality factor, the numerical values are validated. The combination of the theoretical expressions, numerical results and experimental data leads to an important insight into the achievable quality factor value of tuning-fork resonator, namely, that the thermoelastic damping is the main loss mechanism in the micro-comb finger structure and the quality factor varies under different vibration modes. The results demonstrate that the critical geometry dimensions of tuning-fork resonator can be well designed with the assistance of this study.
Interior Pathways to Dissipation of Mesoscale Energy
Energy Technology Data Exchange (ETDEWEB)
Nadiga, Balasubramanya T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2018-01-27
This talk at Goethe University asks What Powers Overturning Circulation? How does Ocean Circulation Equilibrate? There is a HUGE reservoir of energy sitting in the interior ocean. Can fluid dynamic instabilities contribute to the mixing required to drive global overturning circulation? Study designed to eliminate distinguished horizontal surfaces such as bottom BL and surface layer
Wetlands as energy-dissipating systems
Czech Academy of Sciences Publication Activity Database
Pokorný, J.; Květ, Jan; Rejšková, A.; Brom, J.
2010-01-01
Roč. 37, č. 12 (2010), s. 1299-1305 ISSN 1367-5435 Institutional research plan: CEZ:AV0Z60870520 Keywords : wetlands * vegetation * energy fluxes * primary production * landscape management Subject RIV: EF - Botanics Impact factor: 2.416, year: 2010 http://www.springerlink.com/content/y5t4750647q84553/
A simulation for energy dissipation in nuclear reactions
International Nuclear Information System (INIS)
Mshelia, E.D.; Ngadda, Y.H.
1989-01-01
A model for energy dissipation is presented which demonstrates energy transfer from a collective degree of freedom, represented by free motion, into intrinsic modes, represented by four coupled oscillators. The quantum mechanical probability amplitude for internal excitation is expressed as a multiple integral of a product of translational and intrinsic wavefunctions and exactly solved analytically. Its numerical values as a function of quantities of physical interest have been calculated, represented graphically and discussed. The results show that the probability distributions are peaked. (author)
A study of energy dissipation and critical speed of granular flow in a rotating cylinder
Dragomir, Sergiu C.; Sinnott, Mathew D.; Semercigil, S. Eren; Turan, Özden F.
2014-12-01
Tuned vibration absorbers may improve the safety of flexible structures which are prone to excessive oscillation magnitudes under dynamic loads. A novel absorber design proposes sloshing of granular material in a rotating cylinder where the granular material is the energy dissipating agent. As the conventional dissipative elements require maintenance due to the nature of their function, the new design may represent a virtually maintenance free alternative. The angular speed of the cylinder containing particles has a critical centrifuging speed, after which particles remain permanently in contact with the walls and there can be no further dissipation. Until the critical speed, however, dissipation increases proportionally with the angular speed. It is then vital to know the value of the critical speed as the limit of dissipation. The focus of the present study is on determination of the critical centrifuge speed. This critical speed is also of practical importance in bulk-material handling rotary mills, such as dryers and crushers. Experiments and numerical simulations, using Discrete Element Method, are used to determine the critical centrifuging speed. In addition, predictions are given and guidelines are offered for the choice of material properties to maximize the energy dissipation. As a result of a parametric study, the coefficient of friction is found to have the greatest significance on the centrifuging speed.
A dissipated energy comparison to evaluate fatigue resistance using 2-point bending
Directory of Open Access Journals (Sweden)
Cinzia Maggiore
2014-02-01
Full Text Available Fatigue is the main failure mode in pavement engineering. Typically, micro-cracks originate at the bottom of asphalt concrete layer due to horizontal tensile strains. Micro-cracks start to propagate towards the upper layers under repeated loading which can lead to pavement failure. Different methods are usually used to describe fatigue behavior in asphalt materials such as: phenomenological approach, fracture mechanics approach and dissipated energy approach. This paper presents a comparison of fatigue resistances calculated for different dissipated energy models using 2-point bending (2PB at IFSTTAR in Nantes. 2PB tests have been undertaken under different loading and environmental conditions in order to evaluate the properties of the mixtures (stiffness, dissipated energy, fatigue life and healing effect.
The role of coral reef rugosity in dissipating wave energy and coastal protection
Harris, Daniel; Rovere, Alessio; Parravicini, Valeriano; Casella, Elisa
2016-04-01
Coral reefs are the most effective natural barrier in dissipating wave energy through breaking and bed friction. The attenuation of wave energy by coral reef flats is essential in the protection and stability of coral reef aligned coasts and reef islands. However, the effectiveness of wave energy dissipation by coral reefs may be diminished under future climate change scenarios with a potential reduction of coral reef rugosity due to increased stress environmental stress on corals. The physical roughness or rugosity of coral reefs is directly related to ecological diversity, reef health, and hydrodynamic roughness. However, the relationship between physical roughness and hydrodynamic roughness is not well understood despite the crucial role of bed friction in dissipating wave energy in coral reef aligned coasts. We examine the relationship between wave energy dissipation across a fringing reef in relation to the cross-reef ecological zonation and the benthic hydrodynamic roughness. Waves were measured by pressure transducers in a cross-reef transect on the reefs flats and post processed on a wave by wave basis to determine wave statistics such as significant wave height and wave period. Results from direct wave measurement were then used to calibrate a 1D wave dissipation model that incorporates dissipation functions due to bed friction and wave breaking. This model was used to assess the bed roughness required to produce the observed wave height dissipation during propagation from deep water and across the coral reef flats. Changes in wave dissipation was also examined under future scenarios of sea level rise and reduced bed roughness. Three dimensional models of the benthic reef structure were produced through structure-from-motion photogrammetry surveys. Reef rugosity was then determined from these surveys and related to the roughness results from the calibrated model. The results indicate that applying varying roughness coefficients as the benthic ecological
Kinetic Energy Dissipation on Labyrinth Configuration Stepped Spillway
Directory of Open Access Journals (Sweden)
Jaafar S. Maatooq
2017-12-01
Full Text Available In present work a labyrinth (zigzag, in shape has been used to configure the steps of stepped spillway by using the physical model. This configuration does not introduce previously by investigators or in construction techniques of dams or cascades. It would be expected to improve the flow over chute. A magnifying the width path of each step to become, LT, instead of, W, will induce the interlocking between the mainstream and that spread laterally due to labyrinth path. This phenomenon leads to reduce the jet velocities near the surfaces, thus minimizing the ability of cavitation and with increasing a circulation regions the ability of air entrainment be maximized. The results were encouraging, (e.g., the reverse performance has recorded for spillway slope. From the evaluation of outcome, the average recorded of percentage profits of kinetic energy dissipation with a labyrinth shape compared with the results of traditional shape were ranged between (13- 44%. Different predictive formulas have been proposed based on iteration analysis, can be recommended for evaluation and design.
Energy dissipation in head-on collisions of spheres
International Nuclear Information System (INIS)
Krijt, S; Tielens, A G G M; Güttler, C; Heißelmann, D; Dominik, C
2013-01-01
Collisions between spheres are a common ingredient in a variety of scientific problems, and the coefficient of restitution (COR) is a key parameter to describe their outcome. We present a new collision model that treats adhesion and viscoelasticity self-consistently, while energy losses arising from plastic deformation are assumed to be additive. Results show that viscoelasticity can significantly increase the energy that is dissipated in a collision, enhancing the sticking velocity. Furthermore, collisions well above the sticking velocity remain dissipative. We systemically compare the model to a large and unbiased set of published laboratory experiments to show its general applicability. The model is well capable of reproducing the important relation between impact velocity and COR as measured in the experiments, covering a wide range of materials, particle sizes, and collision velocities. Furthermore, the fitting parameters from those curves provide physical parameters such as the surface energy, yield strength, and characteristic viscous relaxation time. Our results show that all three aspects—adhesion, viscoelastic dissipation and plastic deformation—are required for a proper description of the kinetic energy losses in sphere collisions. (paper)
A field theory description of constrained energy-dissipation processes
International Nuclear Information System (INIS)
Mandzhavidze, I.D.; Sisakyan, A.N.
2002-01-01
A field theory description of dissipation processes constrained by a high-symmetry group is given. The formalism is presented in the example of the multiple-hadron production processes, where the transition to the thermodynamic equilibrium results from the kinetic energy of colliding particles dissipating into hadron masses. The dynamics of these processes is restricted because the constraints responsible for the colour charge confinement must be taken into account. We develop a more general S-matrix formulation of the thermodynamics of nonequilibrium dissipative processes and find a necessary and sufficient condition for the validity of this description; this condition is similar to the correlation relaxation condition, which, according to Bogolyubov, must apply as the system approaches equilibrium. This situation must physically occur in processes with an extremely high multiplicity, at least if the hadron mass is nonzero. We also describe a new strong-coupling perturbation scheme, which is useful for taking symmetry restrictions on the dynamics of dissipation processes into account. We review the literature devoted to this problem
Stable schemes for dissipative particle dynamics with conserved energy
Energy Technology Data Exchange (ETDEWEB)
Stoltz, Gabriel, E-mail: stoltz@cermics.enpc.fr
2017-07-01
This article presents a new numerical scheme for the discretization of dissipative particle dynamics with conserved energy. The key idea is to reduce elementary pairwise stochastic dynamics (either fluctuation/dissipation or thermal conduction) to effective single-variable dynamics, and to approximate the solution of these dynamics with one step of a Metropolis–Hastings algorithm. This ensures by construction that no negative internal energies are encountered during the simulation, and hence allows to increase the admissible timesteps to integrate the dynamics, even for systems with small heat capacities. Stability is only limited by the Hamiltonian part of the dynamics, which suggests resorting to multiple timestep strategies where the stochastic part is integrated less frequently than the Hamiltonian one.
Development of a model for baffle energy dissipation in liquid fueled rocket engines
Miller, Nathan A.
In this thesis the energy dissipation from a combined hub and blade baffle structure in a combustion chamber of a liquid-fueled rocket engine is modeled and computed. An analytical model of the flow stabilization due to the effect of combined radial and hub blades was developed. The rate of energy dissipation of the baffle blades was computed using a corner-flow model that included unsteady flow separation and turbulence effects. For the inviscid portion of the flow field, a solution methodology was formulated using an eigenfunction expansion and a velocity potential matching technique. Parameters such as local velocity, elemental path length, effective viscosity, and local energy dissipation rate were computed as a function of the local angle alpha for a representative baffle blade, and compared to results predicted by the Baer-Mitchell blade dissipation model. The sensitivity of the model to the overall engine acoustic oscillation mode, blade length, and thickness was also computed and compared to previous results. Additional studies were performed to determine the sensitivity to input parameters such as the dimensionless turbulence coefficient, the location of the potential difference in the generation of the dividing streamline, the number of baffle blades and the size of the central hub. Stability computations of a test engine indicated that when the baffle length is increased, the baffles provide increased stabilization effects. The model predicts greatest dissipation for radial modes with a hub radius at approximately half the chamber's radius.
Minimum energy dissipation required for a logically irreversible operation
Takeuchi, Naoki; Yoshikawa, Nobuyuki
2018-01-01
According to Landauer's principle, the minimum heat emission required for computing is linked to logical entropy, or logical reversibility. The validity of Landauer's principle has been investigated for several decades and was finally demonstrated in recent experiments by showing that the minimum heat emission is associated with the reduction in logical entropy during a logically irreversible operation. Although the relationship between minimum heat emission and logical reversibility is being revealed, it is not clear how much free energy is required to be dissipated for a logically irreversible operation. In the present study, in order to reveal the connection between logical reversibility and free energy dissipation, we numerically demonstrated logically irreversible protocols using adiabatic superconductor logic. The calculation results of work during the protocol showed that, while the minimum heat emission conforms to Landauer's principle, the free energy dissipation can be arbitrarily reduced by performing the protocol quasistatically. The above results show that logical reversibility is not associated with thermodynamic reversibility, and that heat is not only emitted from logic devices but also absorbed by logic devices. We also formulated the heat emission from adiabatic superconductor logic during a logically irreversible operation at a finite operation speed.
[Study on energy dissipation in modified airlift bioreactor].
Jin, Ren-Cun; Zheng, Ping
2005-09-01
The effects of operational variables and reactor configurations (e.g. diameter of draft tube and the number of static mixers) on energy loss in modified airlift bioreactor were investigated at the first time. The results showed that improving the structure of draft tube could reduce energy loss in the bioreactor. When the diameter of draft tube and the number of static mixers were 4.0cm and 39, respectively, the total energy loss in the modified bioreactor was the least among all the configurations and 23.6% less than that of the conventional counterpart at the same air flowrate. The energy consumption for aeration was the smallest (43.9% less than that of the conventional counterpart) when the diameter of draft tube and the number of static mixers were 5.5cm and 13, respectively. The highest energy dissipation (70% - 80%) occurred in the riser, the bottom zone (about 20%) took the second place and the separator (less than 10%) took the third place. The energy dissipation in the downcomer was neglectable under the conditions in the research. When the energy loss per unit volume was considered, bottom zone stood the first place. It was implied that the riser was the most important zone to cut down the energy loss of the bioreactor and some attention should also be paid to the bottom zone.
Air Entrainment and Energy Dissipation on Gabion Stepped Weirs
Wüthrich, Davide
2014-01-01
In the last three decades the design of stepped spillways regained some interest because of their suitability with new construction methods including gabion placement. In this study, the hydraulic performances of gabion stepped weirs were investigated experimentally in terms of the air-water flow properties and energy dissipation rate. A physical study was performed in a relatively large size facility with a 26.6° slope (1V:2H) and 0.10 m step height. For both gabion and impervious stepped we...
Modelling turbulent energy dissipation in the high-latitude mesosphere
Hall, C. M.; Brekke, A.; Martynenko, O. V.; Namgaladze, A. A.
1998-02-01
The global numerical model of the Earth's thermosphere, ionosphere and protonosphere constructed at the Kaliningrad Observatory of IZMIRAN and Polar Geophysical Institute in Murmansk, (Namgaladze et al., 1991), hereafter referred to as PGI97, is being extended to encompass modelling of the mesosphere. Here we report the first predictions of turbulent intensities in the height regime 80 to 90 km. Recently, Hall (1997) reported estimates of the turbulent energy dissipation rate, ɛ, using the EISCAT VHF radar located in Northern Norway (69°N, 19°E), which has, in turn, been compared to in situ measurements. Thus initial testing of PGI97 has concentrated on the same region. The agreements between PGI97 and EISCAT results for summer and winter solstice mesospheres are good. The general seasonal variation has been investigated, again showing good agreement with the EISCAT results. However, when examining the average energy dissipation in the 80-90 km height regime, the model shows less variability than the observations.
Light heavy - ion dissipative collisions at low energy
International Nuclear Information System (INIS)
Pop, A.; Andronic, A.; Berceanu, I.; Duma, M.; Moisa, D.; Petrovici, M.; Simion, V.; Imme, G.; Lanzano, G.; Pagano, A.; Raciti, G.; Coniglione, R.; Zoppo, A. Del; Piatelli, P.; Sapienza, P.; Colonna, N.; Pantaleo, A.; D'Erasmo, G.
2003-01-01
The collisions of light heavy ions were less studied as compared to the large amount of information on dissipative processes collected for heavy systems. For moderate energy damping both experimental data and theoretical models were concentrated on optimum Q value systematics. The energy domain of complete damping was studied from the challenging point of view of the competition between the deep inelastic orbiting mechanism and the fusion-fission one. Dissipative processes have been investigated experimentally in several light heavy-ion systems, using a complex detector which has as main components two position sensitive ionization chamber. The investigated systems were: 19 F(111.4, 125, 136.9 MeV) + 27 Al, 19 F(111.4, 136.9 MeV) + 12 C and 27 Al(140.14 MeV) + 12 C, 27 Al. Experimental evidence and comparison with theoretical calculations suggesting a mechanism similar to deep inelastic processes in heavy and medium systems, even in the case of completely damped events, will be presented in this work. (authors)
Seismic Behaviour of Reinforced Concrete Slit Shear Walls Energy Dissipators
Directory of Open Access Journals (Sweden)
Sergiu Băetu
2010-01-01
Full Text Available The types of slit walls energy dissipators, from monolith or precast reinforced concrete, proposed by researchers and the seismic behaviour of these types of walls are described. The overall ductility of the structure increases, considering the energy dissipation solutions proposed by the researchers of the reinforced concrete walls, resulting a supplementary safety for the structure. The objective of these solutions is to create an ideal structure for tall multi-storey buildings, that behaves as a rigid structure at low seismic action and turns into a flexible one in case of a high intensity earthquake action. The solutions for increasing ductility proposed in this paper are viable and easily to use in constructions practice. For the analysis of slit wall, the researchers used a series of analytical calculation methods, among the most important being the equivalent frame method and the finite element method, both presented s. 3 of the paper. The researchers concluded that by using this calculations methods, the dynamic behaviour of the reinforced concrete slit walls can be simulated very accurate and realistic.
Identification of energy dissipation in structural joints by means of the energy flow analysis
Gómez, S.S.; Metrikine, A.; Carboni, B.; Lacarbonara, W.
2018-01-01
In this paper, identification of energy dissipation in the joints of a lab-scale structure is accomplished. The identification is carried out by means of an energy flow analysis and experimental data. The devised procedure enables to formulate an energy balance in the vicinity of the joints to
Shock Wave Energy Dissipation by Metal-Organic Framework
Zhou, Xuan; Miao, Yurun; Banlusan, Kiettipong; Shaw, William; Strachan, Alejandro; Suslick, Kenneth; Dlott, Dana
2017-06-01
Metal-organic framework (MOF) such as ZIF-8 and UiO-66 show promising shock energy dissipation abilities through mechano-chemical reactions including bond breaking and pore collapse. In this work, we performed quantitative measurements on the shock wave energy attenuated by MOF films using a laser-driven flyer-plate apparatus. Aluminum flyer plates of 75-um thick were accelerated to speeds up to 2.0 km/s by a flat-top pulsed laser to impact the MOF film. The MOF layer was coated on a 200-nm thick gold mirror, which was deposited previously on glass substrate. Photonic Doppler velocimetry (PDV) was used to track the motions of the gold mirror, which can be converted to the energy flux and fluence of the shock wave that transmitted through the MOF layer. We deduced the shock energy that was attenuated by the MOF film by comparing the transmitted energy flux/fluence obtained with and without the presence of the MOF layer. A two-wave-shaped flux-time curve was obtained with the MOF layer because of its nanoporous structure. Studies on the shock wave energy attenuation by ZIF-8 and UiO-66 were carried out under various flyer speeds and sample thicknesses. We used in situ emission spectroscopy to verify that pore collapse was accompanied by chemical bond breakage. Corresponding author:dlott@illinois.edu.
Energy Dissipation in the Upper Atmospheres of TRAPPIST-1 Planets
Cohen, Ofer; Glocer, Alex; Garraffo, Cecilia; Drake, Jeremy J.; Bell, Jared M.
2018-03-01
We present a method to quantify the upper limit of the energy transmitted from the intense stellar wind to the upper atmospheres of three of the TRAPPIST-1 planets (e, f, and g). We use a formalism that treats the system as two electromagnetic regions, where the efficiency of the energy transmission between one region (the stellar wind at the planetary orbits) to the other (the planetary ionospheres) depends on the relation between the conductances and impedances of the two regions. Since the energy flux of the stellar wind is very high at these planetary orbits, we find that for the case of high transmission efficiency (when the conductances and impedances are close in magnitude), the energy dissipation in the upper planetary atmospheres is also very large. On average, the Ohmic energy can reach 0.5–1 W m‑2, about 1% of the stellar irradiance and 5–15 times the EUV irradiance. Here, using constant values for the ionospheric conductance, we demonstrate that the stellar wind energy could potentially drive large atmospheric heating in terrestrial planets, as well as in hot Jupiters. More detailed calculations are needed to assess the ionospheric conductance and to determine more accurately the amount of heating the stellar wind can drive in close-orbit planets.
A modal approach to modeling spatially distributed vibration energy dissipation.
Energy Technology Data Exchange (ETDEWEB)
Segalman, Daniel Joseph
2010-08-01
The nonlinear behavior of mechanical joints is a confounding element in modeling the dynamic response of structures. Though there has been some progress in recent years in modeling individual joints, modeling the full structure with myriad frictional interfaces has remained an obstinate challenge. A strategy is suggested for structural dynamics modeling that can account for the combined effect of interface friction distributed spatially about the structure. This approach accommodates the following observations: (1) At small to modest amplitudes, the nonlinearity of jointed structures is manifest primarily in the energy dissipation - visible as vibration damping; (2) Correspondingly, measured vibration modes do not change significantly with amplitude; and (3) Significant coupling among the modes does not appear to result at modest amplitudes. The mathematical approach presented here postulates the preservation of linear modes and invests all the nonlinearity in the evolution of the modal coordinates. The constitutive form selected is one that works well in modeling spatially discrete joints. When compared against a mathematical truth model, the distributed dissipation approximation performs well.
Theory of minimum dissipation of energy for the steady state
International Nuclear Information System (INIS)
Chu, T.K.
1992-02-01
The magnetic configuration of an inductively driven steady-state plasma bounded by a surface (or two adjacent surfaces) on which B·n = 0 is force-free: ∇xB = 2αB, where α is a constant, in time and in space. α is the ratio of the Poynting flux to the magnetic helicity flux at the boundary. It is also the ratio of the dissipative rates of the magnetic energy to the magnetic helicity in the plasma. The spatial extent of the configuration is noninfinitesimal. This global constraint is a result of the requirement that, for a steady-state plasma, the rate of change of the vector potential, ∂A/∂t, is constant in time and uniform in space
Plastic deformation enabled energy dissipation in a bionanowire structured armor.
Li, Haoze; Yue, Yonghai; Han, Xiaodong; Li, Xiaodong
2014-05-14
It has been challenging to simultaneously achieve high strength and toughness in engineered materials because of the trade-off relation between the two distinct properties. Nature, however, has elegantly solved this problem. Seashells, commonly referred to as nature's armors, exhibit an unusual resilience against predatory attacks. In this letter, we report an unexpected phenomenon in a bionanowire structured armor-conch shell where the shell's basic building blocks, i.e., the third-order lamellae, exhibit an exceptional plasticity with a maximum strain of 0.7% upon mechanical loading. We attribute such a plastic deformation behavior to the lamella's unique nanoparticle-biopolymer architecture, in which the biopolymer mediates the rotation of aragonite nanoparticles in response to external attacks. We also found that electron beam irradiation facilitates the lamella's plasticity. These findings advance our understanding of seashell's energy dissipating strategy and provide new design guidelines for developing high performance bioinspired materials and sensors.
Dissipation of 'dark energy' by cortex in knowledge retrieval.
Capolupo, Antonio; Freeman, Walter J; Vitiello, Giuseppe
2013-03-01
We have devised a thermodynamic model of cortical neurodynamics expressed at the classical level by neural networks and at the quantum level by dissipative quantum field theory. Our model is based on features in the spatial images of cortical activity newly revealed by high-density electrode arrays. We have incorporated the mechanism and necessity for so-called dark energy in knowledge retrieval. We have extended the model first using the Carnot cycle to define our measures for energy, entropy and temperature, and then using the Rankine cycle to incorporate criticality and phase transitions. We describe the dynamics of two interactive fields of neural activity that express knowledge, one at high and the other at low energy density, and the two operators that create and annihilate the fields. We postulate that the extremely high density of energy sequestered briefly in cortical activity patterns can account for the vividness, richness of associations, and emotional intensity of memories recalled by stimuli. Copyright © 2013 Elsevier B.V. All rights reserved.
Wave dissipation due to spatially varying bottom roughness: Observations from Oahu, Hawaii
Siegelman, M. N.; Merrifield, M. A.; Becker, J. M.; Pawlak, G. R.; Reyns, J.
2016-02-01
The influence of bottom friction on waves shoaling over reef topography prior to breaking is examined using across-shore array of wave sensors on the Leeward side of Oahu during the winter of 2014. Offshore wave heights ranged from 2 to 5 m during a succession of northwest swell events. Wave energy flux is approximately conserved between an offshore wave buoy and the deepest wave sensor at 15 m depth. Between 15 m and 6 m depths, where rough reef bathymetry replaces sand, significant dissipation is inferred with a 60% reduction in the wave energy flux. Equating the energy flux divergence to bottom friction dissipation results in a wave friction factor of 0.38 ± 0.03, higher than typical wave factors reported in previous reef field studies. The estimated friction factor between 6 m and 5 m reduces to 0.14 ± 0.01. AUV surveys of the study site provide high resolution depth measurements that are used to relate bottom roughness to the variable friction factor estimated across the transect. A numerical model is used to assess the influence of the high friction factors on simulations over two-dimensional bathymetry. The results highlight the need for spatially dependent bottom roughness estimates for accurate wave predictions in reef environments.
Mechanism of active transport: free energy dissipation and free energy transduction.
Tanford, C
1982-01-01
The thermodynamic pathway for "chemiosmotic" free energy transduction in active transport is discussed with an ATP-driven Ca2+ pump as an illustrative example. Two innovations are made in the analysis. (i) Free energy dissipated as heat is rigorously excluded from overall free energy bookkeeping by focusing on the dynamic equilibrium state of the chemiosmotic process. (ii) Separate chemical potential terms for free energy donor and transported ions are used to keep track of the thermodynamic ...
Mudflows: Assessment of Energy Dissipation on an Experimental Bottom Grid Device
Directory of Open Access Journals (Sweden)
Francesco De Paola
2011-09-01
Full Text Available Grid devices with a terminal wall barrier have been widely used for dissipation of energy load of water piped from the outfall works of artificial reservoirs. The satisfactory results obtained have led to the commitment to usage of such devices, with good results even in the case of mudflows for which design criteria were suggested. In this study, the experimental results of an evaluation of pressure on a vertical terminal wall are shown with the evaluation of the overall hydrodynamic thrust. The correct evaluation of the dynamic impact of a mudflow front against a structure is an important task in its design procedure. The hydrodynamic drive calculated from the tests with corresponding theoretical model values derived has shown a good matching. According to the test and speed range detected, the maximum dissipation rate due to the wall was about 35% of the available total load.
van Egmond, W. J.; Saakes, M.; Porada, S.; Meuwissen, T.; Buisman, C. J. N.; Hamelers, H. V. M.
2016-09-01
Unlike traditional fossil fuel plants, the wind and the sun provide power only when the renewable resource is available. To accommodate large scale use of renewable energy sources for efficient power production and utilization, energy storage systems are necessary. Here, we introduce a scalable energy storage system which operates by performing cycles during which energy generated from renewable resource is first used to produce highly concentrated brine and diluate, followed up mixing these two solutions in order to generate power. In this work, we present theoretical results of the attainable energy density as function of salt type and concentration. A linearized Nernst-Planck model is used to describe water, salt and charge transport. We validate our model with experiments over wide range of sodium chloride concentrations (0.025-3 m) and current densities (-49 to +33 A m-2). We find that depending on current density, charge and discharge steps have significantly different thermodynamic efficiency. In addition, we show that at optimal current densities, mechanisms of energy dissipation change with salt concentration. We find the highest thermodynamic efficiency at low concentrate concentrations. When using salt concentrations above 1 m, water and co-ion transport contribute to high energy dissipation due to irreversible mixing.
Estimates of M2 Tidal Energy Dissipation from TOPEX/Poseidon Altimeter Data
Egbert, Gary D.; Ray, Richard D.
2001-01-01
Most of the tidal energy dissipation in the ocean occurs in shallow seas, as has long been recognized. However, recent work has suggested that a significant fraction of the dissipation, perhaps 1 TW or more, occurs in the deep ocean. This paper builds further evidence for that conclusion. More than 6 years of data from the TOPEX/Poseidon satellite altimeter are used to map the tidal dissipation rate throughout the world ocean. The dissipation rate is estimated as a balance between the rate of working by tidal forces and the energy flux divergence, computed using currents derived by least squares fitting of the altimeter data and the shallow water equations. Such calculations require dynamical assumptions, in particular about the nature of dissipation. To assess sensitivity of dissipation estimates to input assumptions, a large suite of tidal inversions based on a wide range of drag parameterizations and employing both real and synthetic altimeter data are compared. These experiments and Monte Carlo error fields from a generalized inverse model are used to establish error uncertainties for the dissipation estimates. Owing to the tight constraints on tidal elevation fields provided by the altimeter, area integrals of the energy balance are remarkably insensitive to required dynamical assumptions. Tidal energy dissipation is estimated for all major shallow seas (excluding individual polar seas) and compared with previous model and data-based estimates. Dissipation in the open ocean is significantly tnhanced around major bathymetric features, in a manner consistent with simple theories the generation of baroclinic tides.
Turbulent viscosity and Jupiter's tidal Q. [energy dissipation function
Goldreich, P.; Nicholson, P. D.
1977-01-01
A recent estimate of tidal dissipation by turbulent viscosity in Jupiter's convective interior predicts that the current value of the planet's tidal Q is roughly 5 million. We point out a fundamental error in this calculation, and show that turbulent dissipation alone implies that at present Q is about 50 trillion. Our reduced estimate for the rate of tidal dissipation shows conclusively that tidal torques have produced only negligible modifications of the orbits of the Galilean satellites over the age of the solar system.
Relative Entropy, Interaction Energy and the Nature of Dissipation
Directory of Open Access Journals (Sweden)
Bernard Gaveau
2014-06-01
Full Text Available Many thermodynamic relations involve inequalities, with equality if a process does not involve dissipation. In this article we provide equalities in which the dissipative contribution is shown to involve the relative entropy (a.k.a. Kullback-Leibler divergence. The processes considered are general time evolutions both in classical and quantum mechanics, and the initial state is sometimes thermal, sometimes partially so. By calculating a transport coefficient we show that indeed—at least in this case—the source of dissipation in that coefficient is the relative entropy.
Decay of energy and suppression of Fermi acceleration in a dissipative driven stadium-like billiard.
Livorati, André L P; Caldas, Iberê L; Leonel, Edson D
2012-06-01
The behavior of the average energy for an ensemble of non-interacting particles is studied using scaling arguments in a dissipative time-dependent stadium-like billiard. The dynamics of the system is described by a four dimensional nonlinear mapping. The dissipation is introduced via inelastic collisions between the particles and the moving boundary. For different combinations of initial velocities and damping coefficients, the long time dynamics of the particles leads them to reach different states of final energy and to visit different attractors, which change as the dissipation is varied. The decay of the average energy of the particles, which is observed for a large range of restitution coefficients and different initial velocities, is described using scaling arguments. Since this system exhibits unlimited energy growth in the absence of dissipation, our results for the dissipative case give support to the principle that Fermi acceleration seems not to be a robust phenomenon.
Directory of Open Access Journals (Sweden)
Yushu Bian
2013-01-01
Full Text Available Due to the presence of system flexibility, impact can excite severe large amplitude vibration responses of the flexible robotic manipulator. This impact vibration exhibits characteristics of remarkable nonlinearity and strong energy. The main goal of this study is to put forward an energy-based control method to absorb and attenuate large amplitude impact vibration of the flexible robotic manipulator. The method takes advantage of internal resonance and is implemented through a vibration absorber based on the transfer and dissipation of energy. The addition of the vibration absorber to the flexible arm generates a coupling effect between vibration modes of the system. By means of analysis on 2:1 internal resonance, the exchange of energy is proven to be existent. The impact vibrational energy can be transferred from the arm to the absorber and dissipated through the damping of the absorber. The results of numerical simulations are promising and preliminarily verify that the method is feasible and can be used to combat large amplitude impact vibration of the flexible manipulator undergoing rigid motion.
Extrema principles of entrophy production and energy dissipation in fluid mechanics
Horne, W. Clifton; Karamcheti, Krishnamurty
1988-01-01
A survey is presented of several extrema principles of energy dissipation as applied to problems in fluid mechanics. An exact equation is derived for the dissipation function of a homogeneous, isotropic, Newtonian fluid, with terms associated with irreversible compression or expansion, wave radiation, and the square of the vorticity. By using entropy extrema principles, simple flows such as the incompressible channel flow and the cylindrical vortex are identified as minimal dissipative distributions. The principal notions of stability of parallel shear flows appears to be associated with a maximum dissipation condition. These different conditions are consistent with Prigogine's classification of thermodynamic states into categories of equilibrium, linear nonequilibrium, and nonlinear nonequilibrium thermodynamics; vortices and acoustic waves appear as examples of dissipative structures. The measurements of a typical periodic shear flow, the rectangular wall jet, show that direct measurements of the dissipative terms are possible.
International Nuclear Information System (INIS)
Plekhov, O.A.; Saintier, N.; Palin-Luc, T.; Uvarov, S.V.; Naimark, O.B.
2007-01-01
The infrared and structural investigations of energy dissipation processes in metals subjected to cyclic loading have given impetus to the development of a new thermodynamic model with the capability of describing the energy balance under plastic deformation. The model is based on the statistical description of the mesodefect ensemble evolution and its influence on the dissipation ability of the material. Constitutive equations have been formulated for plastic and structural strains, which allow us to describe the stored and dissipated parts of energy under plastic flow. Numerical results indicate that theoretical predictions are in good agreement with the experimentally observed temperature data
Time-dependent London approach: Dissipation due to out-of-core normal excitations by moving vortices
Kogan, V. G.
2018-03-01
The dissipative currents due to normal excitations are included in the London description. The resulting time-dependent London equations are solved for a moving vortex and a moving vortex lattice. It is shown that the field distribution of a moving vortex loses its cylindrical symmetry. It experiences contraction that is stronger in the direction of the motion than in the direction normal to the velocity v . The London contribution of normal currents to dissipation is small relative to the Bardeen-Stephen core dissipation at small velocities, but it approaches the latter at high velocities, where this contribution is no longer proportional to v2. To minimize the London contribution to dissipation, the vortex lattice is oriented so as to have one of the unit cell vectors along the velocity. This effect is seen in experiments and predicted within the time-dependent Ginzburg-Landau theory.
Natural convection in an adiabatic vertical channel due to a dissipated heat element
International Nuclear Information System (INIS)
Ramos, M.A.M.S.
1986-01-01
An experimental study was perfomed on natural convection heat transfer to air in a vertical channel due to an isothermal heated element attached in one of the walls of the channel. The heated element dissipates heat due to the Joule effect. To determine the heat transfer coefficient, it is necessary to evaluate the heat transferred to air by natural convenction alone. Hence, the heat lost by the element due to conduction and radiation is evaluated in order to correct the measured heat transfer. The natural-convenction heat transfer coefficient is a function of the following parameters: the temperature difference between the element and the ambient air, the position of the element in the channel, and the channel spacing. An optimal value of the channel spacing, when the heat transfer coefficient attains its maximum value, was observed for each of the temperature difference investigated. These maximum values may be up to 25% higher than the value for the case of infinite spacing. Comparisons are made with results available in the literature for similar configurations, and the values found in this work are higher. (author) [pt
Hisashi Ozawa; Shinya Shimokawa
2015-01-01
The formation process of circulatory motion of a tropical cyclone is investigated from a thermodynamic viewpoint. The generation rate of mechanical energy by a fluid motion under diabatic heating and cooling, and the dissipation rate of this energy due to irreversible processes are formulated from the first and second laws of thermodynamics. This formulation is applied to a tropical cyclone, and the formation process of the circulatory motion is examined from a balance between the generation ...
Directory of Open Access Journals (Sweden)
Rajneesh Kumar
2014-01-01
Full Text Available The reflection of plane waves at the free surface of thermally conducting micropolar elastic medium with two temperatures is studied. The theory of thermoelasticity with and without energy dissipation is used to investigate the problem. The expressions for amplitudes ratios of reflected waves at different angles of incident wave are obtained. Dissipation of energy and two-temperature effects on these amplitude ratios with angle of incidence are depicted graphically. Some special and particular cases are also deduced.
Chloroplast thylakoid structure in evergreen leaves employing strong thermal energy dissipation.
Demmig-Adams, Barbara; Muller, Onno; Stewart, Jared J; Cohu, Christopher M; Adams, William W
2015-11-01
In nature, photosynthetic organisms cope with highly variable light environments--intensities varying over orders of magnitudes as well as rapid fluctuations over seconds-to-minutes--by alternating between (a) highly effective absorption and photochemical conversion of light levels limiting to photosynthesis and (b) powerful photoprotective thermal dissipation of potentially damaging light levels exceeding those that can be utilized in photosynthesis. Adjustments of the photosynthetic apparatus to changes in light environment involve biophysical, biochemical, and structural adjustments. We used electron micrographs to assess overall thylakoid grana structure in evergreen species that exhibit much stronger maximal levels of thermal energy dissipation than the more commonly studied annual species. Our findings indicate an association between partial or complete unstacking of thylakoid grana structure and strong reversible thermal energy dissipation that, in contrast to what has been reported for annual species with much lower maximal levels of energy dissipation, is similar to what is seen under photoinhibitory conditions. For a tropical evergreen with tall grana stacks, a loosening, or vertical unstacking, of grana was seen in sun-grown plants exhibiting pronounced pH-dependent, rapidly reversible thermal energy dissipation as well as for sudden low-to-high-light transfer of shade-grown plants that responded with photoinhibition, characterized by strong dark-sustained, pH-independent thermal energy dissipation and photosystem II (PSII) inactivation. On the other hand, full-sun exposed subalpine confers with rather short grana stacks transitioned from autumn to winter via conversion of most thylakoids from granal to stromal lamellae concomitant with photoinhibitory photosynthetic inactivation and sustained thermal energy dissipation. We propose that these two types of changes (partial or complete unstacking of grana) in thylakoid arrangement are both associated with
K-12 Teacher Understanding of Energy Conservation: Conceptual Metaphor, Dissipation, and Degradation
Daane, Abigail R.
In K-12 educational settings, conservation of energy is typically presented in two ways: the conservation of energy principle (energy is neither created nor destroyed) and the sociopolitical need to conserve energy (we guard against energy being used up). These two meanings of conservation typically remain disconnected from each other and can appear contradictory, even after instruction. In an effort to support teachers in building robust understandings of energy from their existing knowledge, I designed a study to investigate the productive ideas in K-12 teachers' conversations about energy. A micro-analysis of discourse, gestures, and artifacts of professional development courses revealed teachers' productive ideas about three aspects of energy: conceptual metaphor, dissipation and degradation. In learning about energy, K-12 teachers come to use conceptual metaphors in their own language and value attending to students' metaphorical language as a means of formative assessment. Teachers' conversations about dissipation suggest that apparent difficulties with energy conservation may have their roots in a strong association between forms of energy (thermal) and their perceptible indicators (warmth). Teachers address this challenge by employing an exaggeration strategy to locate the dissipated thermal energy, making the energy indicator perceptible. Finally, teachers' unprompted statements about sociopolitical aspects of energy are related to both statements from the NGSS and aspects of energy degradation. I conclude that energy conservation can be better taught and learned in K-12 Education by: 1) understanding and applying conceptual metaphors about energy in K-12 settings, 2) using prior experiences to better understand dissipative energy processes involving imperceptible thermal energy, thereby understanding how energy conservation applies in all situations, and 3) connecting productive ideas about sociopolitical aspects of energy to canonical physics. Keywords
Light Heavy-Ion Dissipative Collisions at Low Energy
Pop, A.; Andronic, A.; Berceanu, I.; Duma, M.; Moisa, D.; Petrovici, M.; Simion, V.; Immé, G.; Lanzanó, G.; Pagano, A.; Raciti, G.; Coniglione, R.; Del Zoppo, A.; Piatelli, P.; Sapienza, P.; Colonna, N.; D'Erasmo, G.; Pantaleo, A.
2004-09-01
Dissipative processes have been investigated experimentally in several light heavy-ion systems, using a complex detector which has as main components two position sensitive ionization chambers. Experimental evidence and comparison with theoretical calculations suggest a mechanism similar to deep inelastic processes in heavy and medium systems, even in the case of completely damped events. Note from Publisher: This article contains the abstract and references only.
Energy conversion and dissipation at dipolarization fronts: Theory, modeling and MMS observations
Sitnov, M. I.; Motoba, T.; Merkin, V. G.; Ohtani, S.; Cohen, I. J.; Mauk, B.; Vines, S. K.; Anderson, B. J.; Moore, T. E.; Torbert, R. B.; Giles, B. L.; Burch, J. L.
2017-12-01
Magnetic reconnection is one of the most important energy conversion mechanisms in space plasmas. In the classical picture it converts the energy of antiparallel magnetic fields into the kinetic and thermal energy of accelerated plasma particles in reconnection exhausts. It also involves energy dissipation near the X-line. This classical picture may be substantially modified in real space plasma configurations, such as the dayside magnetopause and the magnetotail. In particular, in the magnetotail the flows of accelerated particles may be strongly asymmetric along the tail with the domination of earthward flows. At the same time, strong energy conversion and even dissipation may occur away from the X-line, in particular, at dipolarization fronts. Here we present a theoretical picture of spontaneous magnetotail reconnection based on 3-D PIC simulations with the focus on plasma bulk flows, energy conversion and dissipation. This picture is compared with some observations from the MMS tail season. An important finding from these observations is that dipolarizations fronts may not only be regions of the total energy conversion with jE>0, but they may also be the sites of energy dissipation, both positive (jE'>0, E' is the electric field E in the system moving with one of the plasma species) and negative (jE'<0). Observations are further compared with theory and modeling that predict the specific location and sign of the energy dissipation at fronts depending on their evolution phase (e.g., formation, propagation, braking).
Evaluation of leaf energy dissipation by the Photochemical Reflectance
Raddi, S.; Magnani, F.
Starting from the early paper by Heber (1969), several studies have demonstrated a subtle shift in leaf spectroscopic characteristics (both absorbance and reflectance) in response to rapid changes in environmental conditions. More recent work, briefly reviewed here, has also demonstrated the existence of two components in the maked peak centered at 505-540 nm: an irreversible component, attributed to the interconversion of leaf xanthophylls, and a reversible component at slightly longer wavelengths, resulting from conformational changes induced by the buildup of a pH gradient across the thylakoid membrane associated with photosynthetic electron transport. Both processes (xanthophyll de-epoxidation and conformational changes) are known to contribute to the dissipation of excess energy in Photosystem II (PSII). Leaf spectroscopy could therefore provide a powerful non-invasive tool for the determination of leaf photosynthetic processes. This led to the development of the normalized spectral index PRI (Photochemical Reflectance Index; Gamon, Penuelas &Field 1992; Gamon, Serrano &Surfus 1997), which relates the functional signal at 531 nm to a reference signal at 570 nm. The index has been found to track diurnal changes in xanthophyll de-epoxidation state, radiation use efficiency and fluorescence in response to light, both at the leaf and more recently at the canopy level. A common relationship has also beenreported across species and functional types, although such a generality has not always been confirmed. Recent reports (Stylinski et al. 2000) have also hinted of a possible link between PRI and leaf photosynthetic potential, possibly through the correlation between xanthophyll content and electron transport machinery in the chloroplast. Such a link, if confirmed, could prove very useful for the remote sensing and modelling ofvegetation. Some of these open questions were addressed in the present study. The correlation between leaf function and reflectance was
Anomalous dissipation and kinetic-energy distribution in pipes at very high Reynolds numbers.
Chen, Xi; Wei, Bo-Bo; Hussain, Fazle; She, Zhen-Su
2016-01-01
A symmetry-based theory is developed for the description of (streamwise) kinetic energy K in turbulent pipes at extremely high Reynolds numbers (Re's). The theory assumes a mesolayer with continual deformation of wall-attached eddies which introduce an anomalous dissipation, breaking the exact balance between production and dissipation. An outer peak of K is predicted above a critical Re of 10^{4}, in good agreement with experimental data. The theory offers an alternative explanation for the recently discovered logarithmic distribution of K. The concept of anomalous dissipation is further supported by a significant modification of the k-ω equation, yielding an accurate prediction of the entire K profile.
Estimation of turbulent energy dissipation in the boundary layer using Smoke Image Velocimetry
Mikheev, N. I.; Goltsman, A. E.; Saushin, I. I.; Dushina, O. A.
2017-08-01
Turbulent energy dissipation in the turbulent boundary layer has been estimated experimentally. Dissipation has been derived from dynamics of two-component instantaneous velocity vector fields measured by an optical method. Smoke Image Velocimetry technique based on digital processing of smoke visualization of flow and adapted to relatively large smoke displacement between two consecutive video frames has been employed. The obtained dissipation profiles have been compared with measurements by multi-sensor hot-wire anemometers, stereo PIV, Tomo-3D-PTV with VIC+, and DNS results.
Multiwalled Carbon Nanotube Nanofluids Used for Heat Dissipation in Hybrid Green Energy Systems
Directory of Open Access Journals (Sweden)
Yi-Hsuan Hung
2014-01-01
Full Text Available This study was conducted to characterize carbon nanotube (CNT/water nanofluids (CNWNFs and to apply the nanofluids in a heat-dissipation system of dual green energy sources. CNTs were mixed with water in weight fractions of 0.125%, 0.25%, and 0.5% to produce nanofluids. The thermal conductivity, density, viscosity, and specific heat of the nanofluids were measured. An experimental platform consisting of a simulated dual energy source and a microchip controller was established to evaluate the heat-dissipation performance. Two indices, the heat dissipation enhancement ratio and specific heat dissipation enhancement ratio (SHDER, were defined and calculated. The CNWNFs with a CNT concentration of 0.125 wt.% were used because they exhibited the highest SHDER. The steady-state performance was evaluated at 2 flow rates, 11 hybrid flow ratios, and 3 heating ratios for a total power of 1000 W. The transient behavior of the energy sources at preset optimal temperatures was examined, and the CNWNFs exhibited average increases in stability and heat dissipation efficiency of 36.2% and 5%, respectively, compared with water. This nanofluid heat-dissipation system is expected to be integrated with real dual energy sources in the near future.
Energy Technology Data Exchange (ETDEWEB)
Mérida, Fernando [Deparment of Chemical Engineering, University of Puerto Rico, Mayagüez, P.O. Box 9046, Mayagüez, PR 00680 (United States); Chiu-Lam, Andreina [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); Bohórquez, Ana C. [J. Crayton Pruitt Family Department of Biomedical Engineering, University of Florida, P.O. Box 116131, Gainesville, FL 32611-6131 (United States); Maldonado-Camargo, Lorena [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); Pérez, María-Eglée; Pericchi, Luis [Department of Mathematics, University of Puerto Rico, Río Piedras, P.O. Box 70377, San Juan, PR 00936-8377 (United States); Torres-Lugo, Madeline [Deparment of Chemical Engineering, University of Puerto Rico, Mayagüez, P.O. Box 9046, Mayagüez, PR 00680 (United States); Rinaldi, Carlos, E-mail: carlos.rinaldi@bme.ufl.edu [Department of Chemical Engineering, University of Florida, P.O. Box 116005, Gainesville, FL 32611-6005 (United States); J. Crayton Pruitt Family Department of Biomedical Engineering, University of Florida, P.O. Box 116131, Gainesville, FL 32611-6131 (United States)
2015-11-15
Magnetic Fluid Hyperthermia (MFH) uses heat generated by magnetic nanoparticles exposed to alternating magnetic fields to cause a temperature increase in tumors to the hyperthermia range (43–47 °C), inducing apoptotic cancer cell death. As with all cancer nanomedicines, one of the most significant challenges with MFH is achieving high nanoparticle accumulation at the tumor site. This motivates development of synthesis strategies that maximize the rate of energy dissipation of iron oxide magnetic nanoparticles, preferable due to their intrinsic biocompatibility. This has led to development of synthesis strategies that, although attractive from the point of view of chemical elegance, may not be suitable for scale-up to quantities necessary for clinical use. On the other hand, to date the aqueous co-precipitation synthesis, which readily yields gram quantities of nanoparticles, has only been reported to yield sufficiently high specific absorption rates after laborious size selective fractionation. This work focuses on improvements to the aqueous co-precipitation of iron oxide nanoparticles to increase the specific absorption rate (SAR), by optimizing synthesis conditions and the subsequent peptization step. Heating efficiencies up to 1048 W/g{sub Fe} (36.5 kA/m, 341 kHz; ILP=2.3 nH m{sup 2} kg{sup −1}) were obtained, which represent one of the highest values reported for iron oxide particles synthesized by co-precipitation without size-selective fractionation. Furthermore, particles reached SAR values of up to 719 W/g{sub Fe} (36.5 kA/m, 341 kHz; ILP=1.6 nH m{sup 2} kg{sup −1}) when in a solid matrix, demonstrating they were capable of significant rates of energy dissipation even when restricted from physical rotation. Reduction in energy dissipation rate due to immobilization has been identified as an obstacle to clinical translation of MFH. Hence, particles obtained with the conditions reported here have great potential for application in nanoscale thermal
Directory of Open Access Journals (Sweden)
Hisashi Ozawa
2015-01-01
Full Text Available The formation process of circulatory motion of a tropical cyclone is investigated from a thermodynamic viewpoint. The generation rate of mechanical energy by a fluid motion under diabatic heating and cooling, and the dissipation rate of this energy due to irreversible processes are formulated from the first and second laws of thermodynamics. This formulation is applied to a tropical cyclone, and the formation process of the circulatory motion is examined from a balance between the generation and dissipation rates of mechanical energy in the fluid system. We find from this formulation and data analysis that the thermodynamic efficiency of tropical cyclones is about 40% lower than the Carnot maximum efficiency because of the presence of thermal dissipation due to irreversible transport of sensible and latent heat in the atmosphere. We show that a tropical cyclone tends to develop within a few days through a feedback supply of mechanical energy when the sea surface temperature is higher than 300 K, and when the horizontal scale of circulation becomes larger than the vertical height of the troposphere. This result is consistent with the critical radius of 50 km and the corresponding central pressure of about 995 hPa found in statistical properties of typhoons observed in the western North Pacific.
Relationship between dynamical entropy and energy dissipation far from thermodynamic equilibrium
Green, Jason R.; Costa, Anthony B.; Grzybowski, Bartosz A.; Szleifer, Igal
2013-01-01
Connections between microscopic dynamical observables and macroscopic nonequilibrium (NE) properties have been pursued in statistical physics since Boltzmann, Gibbs, and Maxwell. The simulations we describe here establish a relationship between the Kolmogorov–Sinai entropy and the energy dissipated as heat from a NE system to its environment. First, we show that the Kolmogorov–Sinai or dynamical entropy can be separated into system and bath components and that the entropy of the system characterizes the dynamics of energy dissipation. Second, we find that the average change in the system dynamical entropy is linearly related to the average change in the energy dissipated to the bath. The constant energy and time scales of the bath fix the dynamical relationship between these two quantities. These results provide a link between microscopic dynamical variables and the macroscopic energetics of NE processes. PMID:24065832
How gate setup and turn radii influence energy dissipation in slalom ski racing.
Supej, Matej; Holmberg, Hans-Christer
2010-11-01
This study examined whether gate setup and turn radii influence energy dissipation in slalom skiing. 3D kinematical measurements were performed over two runs on the same slope in a WC slalom competition with two different gate setups: 1) open gates (OG) and 2) open gates with a delayed gate (DG). Using the arithmetic mean of the skis' turn radii (R(AMS)) the slalom turns were divided into 1) initiation phase (R(AMS) > 15 m) and steering phase (R(AMS) skiing (all p < .05). In both gate setups the highest F and the highest energy dissipation were present in the steering phase, whereas the correlation between R(AMS) and energy dissipation was low (OG: r = .364 and DG: r = .214, both p < .001). In summary, compared with plain open gates, an additional delayed gate prolonged the turn radii and decreased energy dissipation in the beginning of the initiation phase, despite the fact that the relative frequency of occurrence of the highest energy dissipation was higher in DG.
International Nuclear Information System (INIS)
Hameed, A.; Qazi, A.U.; Rasool, M.
2014-01-01
One of the major concerns in structural engineering is the development of new design concepts to improve structural performance and safety from the damaging effects of destructive earthquakes and winds. With the intent to achieve cost-effective seismic-resistant constructions the structures must be constructed to dissipate a large amount of seismic energy. Supplemental damping strategies are useful for improving the seismic response of structures to natural and manmade hazards. Passive energy dissipation devices, when integrated into a structure, dissipate a part of the input energy, thereby reducing energy dissipation requirement on primary structural members and reducing probable structural damage. The purpose of this research is to study the performance of building structure by using passive energy dissipation devices. Different types of devices used in this study are hysteretic dampers, friction dampers viscous and visco-elastic dampers. The finite element modeling technique is used to observe the behavior of structure with dampers. Three prototype concrete buildings (3, 5 and 10 Story) with same configuration are analyzed with damper using time history analysis. The buildings are analyzed with different types of dampers and by using different variation of their properties along the height of the building and the responses of buildings are observed in terms of, displacements, base shear and floor accelerations. It is found that the viscous and visco-elastic dampers are more effective for 3 and 5 storey buildings while friction and hysteresis dampers are effective for 10 storeys. (author)
Theoretical and numerical study of hydraulic characteristics of orifice energy dissipator
Directory of Open Access Journals (Sweden)
Ning He
2010-06-01
Full Text Available Different factors affecting the efficiency of the orifice energy dissipator were investigated based on a series of theoretical analyses and numerical simulations. The main factors investigated by dimension analysis were identified, including the Reynolds number (Re, the ratio of the orifice diameter to the inner diameter of the pipe (d/D, and the ratio of distances between orifices to the inner diameter of the pipe (L/D. Then, numerical simulations were conducted with a k-ɛ two-equation turbulence model. The calculation results show the following: Hydraulic characteristics change dramatically as flow passes through the orifice, with abruptly increasing velocity and turbulent energy, and decreasing pressure. The turbulent energy appears to be low in the middle and high near the pipe wall. For the energy dissipation setup with only one orifice, when Re is smaller than 105, the orifice energy dissipation coefficient K increases rapidly with the increase of Re. When Re is larger than 105, K gradually stabilizes. As d/D increases, K and the length of the recirculation region L1 show similar variation patterns, which inversely vary with d/D. The function curves can be approximated as straight lines. For the energy dissipation model with two orifices, because of different incoming flows at different orifices, the energy dissipation coefficient of the second orifice (K2 is smaller than that of the first. If L/D is less than 5, the K value of the L/D model, depending on the variation of K2, increases with the spacing between two orifices L, and an orifice cannot fulfill its energy dissipation function. If L/D is greater than 5, K2 tends to be steady; thus, the K value of the L/D model gradually stabilizes. Then, the flow fully develops, and L has almost no impact on the value of K.
Effects of sterilization on the energy-dissipating properties of balsa wood
Sorkin, A. B.
1969-01-01
Technical report on the effects of sterilization on the energy-dissipating properties of balsa wood is given. Sterilization by ethylene oxide plus heat enhances the average specific energy of balsa while plastic impregnation followed by irradiation-induced polymerization does not.
Zhao, Jieliang; Huang, He; Yan, Shaoze
2017-03-01
Whether for insects or for aircrafts, landing is one of the indispensable links in the verification of airworthiness safety. The mechanisms by which insects achieve a fast and stable landing remain unclear. An intriguing example is provided by honeybees (Apis mellifera ligustica), which use the swinging motion of their abdomen to dissipate residual flying energy and to achieve a smooth, stable, and quick landing. By using a high-speed camera, we observed that touchdown is initiated by honeybees extending their front legs or antennae and then landing softly on a wall. After touchdown, they swing the rest of their bodies until all flying energy is dissipated. We suggested a simplified model with mass-spring dampers for the body of the honeybee and revealed the mechanism of flying energy transfer and dissipation in detail. Results demonstrate that body translation and abdomen swinging help honeybees dissipate residual flying energy and orchestrate smooth landings. The initial kinetic energy of flying is transformed into the kinetic energy of the abdomen's rotary movement. Then, the kinetic energy of rotary movement is converted into thermal energy during the swinging cycle. This strategy provides more insight into the mechanism of insect flying, which further inspires better design on aerial vehicle with better landing performance.
Energy density of a dissipative polarizable solid by a Lagrangean formalism
International Nuclear Information System (INIS)
Englman, R.; Yahalom, A.
2003-01-01
A Lagrangean for the dynamics of an electromagnetic field in a dispersive and dissipative material is constructed (adapting some ideas by Bekenstein and Hannay) and an expression for the energy density that is positive is obtained from it. The expression contains extra (sink) degrees of freedom that represent dissipating modes. In simplified cases the sink modes can be eliminated to yield an energy density expression in terms of the electromagnetic fields, the polarization and the magnetization only, but which contains parameters associated with the sink modes. The method of adding extra modes can be used to set up a Lagrangean formalism for dissipative systems in general, such that will reinstate time-translation invariance and will yield a unique energy density
Imaging of nonlocal hot-electron energy dissipation via shot noise.
Weng, Qianchun; Komiyama, Susumu; Yang, Le; An, Zhenghua; Chen, Pingping; Biehs, Svend-Age; Kajihara, Yusuke; Lu, Wei
2018-03-29
In modern microelectronic devices, hot electrons accelerate, scatter, and dissipate energy in nanoscale dimensions. Despite recent progress in nanothermometry, direct real-space mapping of hot-electron energy dissipation is challenging as existing techniques are restricted to probing the lattice rather than the electrons. We realize electronic nanothermometry by measuring local current fluctuations, or shot noise, associated with ultrafast hot-electron kinetic processes (~21 terahertz). Exploiting a scanning and contact-free tungsten tip as a local noise probe, we directly visualize hot-electron distributions prior to their thermal equilibration with the host GaAs/AlGaAs crystal lattice. With nanoconstriction devices, we reveal unexpected nonlocal energy dissipation at room temperature, which is reminiscent of ballistic transport of low temperature quantum conductors. Copyright © 2018, American Association for the Advancement of Science.
ENERGY DISSIPATION THROUGH QUASI-STATIC TIDES IN WHITE DWARF BINARIES
International Nuclear Information System (INIS)
Willems, B.; Deloye, C. J.; Kalogera, V.
2010-01-01
We present a formalism to study tidal interactions in white dwarf binaries in the limiting case of quasi-static tides, in which the tidal forcing frequencies are small, compared to the inverse of the white dwarf's dynamical timescale. The formalism is valid for arbitrary orbital eccentricities and therefore applicable to white dwarf binaries in the Galactic disk as well as globular clusters. In the quasi-static limit, the total perturbation of the gravitational potential shows a phase shift with respect to the position of the companion, the magnitude of which is determined primarily by the efficiency of energy dissipation through convective damping. We determine rates of secular evolution of the orbital elements and white dwarf rotational angular velocity for a 0.3 M sun helium white dwarf in binaries with orbital frequencies in the Laser Interferometer Space Antenna (LISA) gravitational wave frequency band and companion masses ranging from 0.3 M sun to 10 5 M sun . The resulting tidal evolution timescales for the orbital semimajor axis are longer than a Hubble time, so that convective damping of quasi-static tides need not be considered in the construction of gravitational wave templates of white dwarf binaries in the LISA band. Spin-up of the white dwarf, on the other hand, can occur on timescales of less than 10 Myr, provided that the white dwarf is initially rotating with a frequency much smaller than the orbital frequency. For semi-detached white dwarf binaries spin-up can occur on timescales of less than 1 Myr. Nevertheless, the timescales remain longer than the orbital inspiral timescales due to gravitational radiation, so that the degree of asynchronism in these binaries increases. As a consequence, tidal forcing eventually occurs at forcing frequencies beyond the quasi-static tide approximation. For the shortest period binaries, energy dissipation is therefore expected to take place through dynamic tides and resonantly excited g-modes.
Moroz, Adam
2009-06-11
The maximum energy dissipation principle is employed to nonlinear chemical thermodynamics in terms of distance variable (generalized displacement) from the global equilibrium, applying the optimal control interpretation to develop a variational formulation. The cost-like functional was chosen to support the suggestion that such a formulation corresponds to the maximum energy dissipation principle. Using this approach, the variational framework was proposed for a nonlinear chemical thermodynamics, including a general cooperative kinetics model. The formulation is in good agreement with standard linear nonequilibrium chemical thermodynamics.
Energy conserving and potential-enstrophy dissipating schemes for the shallow water equations
Arakawa, Akio; Hsu, Yueh-Jiuan G.
1990-01-01
To incorporate potential enstrophy dissipation into discrete shallow water equations with no or arbitrarily small energy dissipation, a family of finite-difference schemes have been derived with which potential enstrophy is guaranteed to decrease while energy is conserved (when the mass flux is nondivergent and time is continuous). Among this family of schemes, there is a member that minimizes the spurious impact of infinite potential vorticities associated with infinitesimal fluid depth. The scheme is, therefore, useful for problems in which the free surface may intersect with the lower boundary.
International Nuclear Information System (INIS)
Kun, S.Yu.; WITS Univ., Johannesburg; Noerenberg, W.; TH Darmstadt; Papa, M.
1992-09-01
We analyze the energy autocorrelation functions and the energy coherence lengths in the strongly dissipative collision 28 Si(E lab = 130 MeV) + 4 8Ti for Z=11 and 12 reaction fragments. It is found that in order to obtain a good fit of both the energy averaged angular distributions and the angular dependence of the energy coherence lengths one has to take into account (i) the dissipation and fluctuation of the relative angular momentum of the dinucleus and (ii) the contribution from direct (fast) reactions in addition to the statistical (relatively slow) interaction processes. The established angular dependence is a direct consequence of the angular-momentum dissipation-fluctuation effects on the time-space evolution of the intermediate dinucleus. (orig.)
Energy Technology Data Exchange (ETDEWEB)
Zhukov, A.A. [N.L. Dukhov All-Russia Research Institute of Automatics, 127055 Moscow (Russian Federation); National Research Nuclear University (MEPhI), 115409 Moscow (Russian Federation); Shapiro, D.S., E-mail: shapiro.dima@gmail.com [N.L. Dukhov All-Russia Research Institute of Automatics, 127055 Moscow (Russian Federation); V.A. Kotel' nikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, 125009 Moscow (Russian Federation); Moscow Institute of Physics and Technology, Dolgoprudny, Moscow Region 141700 (Russian Federation); National University of Science and Technology MISIS, 119049 Moscow (Russian Federation); Remizov, S.V. [N.L. Dukhov All-Russia Research Institute of Automatics, 127055 Moscow (Russian Federation); V.A. Kotel' nikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, 125009 Moscow (Russian Federation); Pogosov, W.V. [N.L. Dukhov All-Russia Research Institute of Automatics, 127055 Moscow (Russian Federation); Moscow Institute of Physics and Technology, Dolgoprudny, Moscow Region 141700 (Russian Federation); Institute for Theoretical and Applied Electrodynamics, Russian Academy of Sciences, 125412 Moscow (Russian Federation); Lozovik, Yu.E. [N.L. Dukhov All-Russia Research Institute of Automatics, 127055 Moscow (Russian Federation); National Research Nuclear University (MEPhI), 115409 Moscow (Russian Federation); Moscow Institute of Physics and Technology, Dolgoprudny, Moscow Region 141700 (Russian Federation); Institute of Spectroscopy, Russian Academy of Sciences, 142190 Moscow Region, Troitsk (Russian Federation)
2017-02-12
We consider a superconducting qubit coupled to the nonstationary transmission line cavity with modulated frequency taking into account energy dissipation. Previously, it was demonstrated that in the case of a single nonadiabatical modulation of a cavity frequency there are two channels of a two-level system excitation which are due to the absorption of Casimir photons and due to the counterrotating wave processes responsible for the dynamical Lamb effect. We show that the parametric periodical modulation of the resonator frequency can increase dramatically the excitation probability. Remarkably, counterrotating wave processes under such a modulation start to play an important role even in the resonant regime. Our predictions can be used to control qubit-resonator quantum states as well as to study experimentally different channels of a parametric qubit excitation. - Highlights: • Coupled qubit-resonator system under the modulation of a resonator frequency is considered. • Counterrotating terms of the Hamiltonian are of importance even in the resonance. • Qubit excited state population is highest if driving frequency matches dressed-state energy.
The Energy Dissipation of Propagating Cracks in Solnhofen Limestone
Bertram, A.; Kalthoff, J. F.
2002-12-01
Crack propagation events are initiated in Solnhofen limestone under impact loading conditions. The Fracture energy respectively the fracture toughness and the velocity of propagating cracks are measured by means of an optimized strain gauge measuring technique. Cracks are accelerated to velocities in the range of 1500 m/s. The measured crack propagation energies/crack propagation toughnesses are significantly higher than the crack initiation energy/crack initiation toughness. Control measurements on the basis of a global energy approach by means of Charpy pendulum impact tests verify the found behaviour. The results explain characteristic peculiarities of the crack propagation behaviour of brittle fracture in rock. Keywords: Fracture energy, fracture toughness, crack propagation, crack velocity, rock
Directory of Open Access Journals (Sweden)
M. Wacławczyk
2017-11-01
Full Text Available In this paper we propose two approaches to estimating the turbulent kinetic energy (TKE dissipation rate, based on the zero-crossing method by Sreenivasan et al. (1983. The original formulation requires a fine resolution of the measured signal, down to the smallest dissipative scales. However, due to finite sampling frequency, as well as measurement errors, velocity time series obtained from airborne experiments are characterized by the presence of effective spectral cutoffs. In contrast to the original formulation the new approaches are suitable for use with signals originating from airborne experiments. The suitability of the new approaches is tested using measurement data obtained during the Physics of Stratocumulus Top (POST airborne research campaign as well as synthetic turbulence data. They appear useful and complementary to existing methods. We show the number-of-crossings-based approaches respond differently to errors due to finite sampling and finite averaging than the classical power spectral method. Hence, their application for the case of short signals and small sampling frequencies is particularly interesting, as it can increase the robustness of turbulent kinetic energy dissipation rate retrieval.
Wacławczyk, Marta; Ma, Yong-Feng; Kopeć, Jacek M.; Malinowski, Szymon P.
2017-11-01
In this paper we propose two approaches to estimating the turbulent kinetic energy (TKE) dissipation rate, based on the zero-crossing method by Sreenivasan et al. (1983). The original formulation requires a fine resolution of the measured signal, down to the smallest dissipative scales. However, due to finite sampling frequency, as well as measurement errors, velocity time series obtained from airborne experiments are characterized by the presence of effective spectral cutoffs. In contrast to the original formulation the new approaches are suitable for use with signals originating from airborne experiments. The suitability of the new approaches is tested using measurement data obtained during the Physics of Stratocumulus Top (POST) airborne research campaign as well as synthetic turbulence data. They appear useful and complementary to existing methods. We show the number-of-crossings-based approaches respond differently to errors due to finite sampling and finite averaging than the classical power spectral method. Hence, their application for the case of short signals and small sampling frequencies is particularly interesting, as it can increase the robustness of turbulent kinetic energy dissipation rate retrieval.
International Nuclear Information System (INIS)
Borderie, B.; Rivet, M.F.; Tassan-Got, L.
1990-01-01
For several years a new field in nuclear physics has been opened by the opportunity to accelerate heavy ions through an energy domain including the Fermi energy of nucleons. This new domain has to be seen as a link between dissipative processes observed at low energies, dominated by mean field considerations, and high energy collisions for which nucleon-nucleon collisions play an important role. This paper reviews our present knowledge on peripheral collisions. A reminder of contiguous energy domains is done as well as their extension in the new field. Specific calculations are also presented. Finally a wide comparison between experiments and calculations is performed. A fast dissipative stage proves to be responsible for the dominant mechanisms involved, at least when the incident energy is lower than 50 MeV/nucleon
Yeow, C H; Lee, P V S; Goh, J C H
2009-08-25
Lack of the necessary magnitude of energy dissipation by lower extremity joint muscles may be implicated in elevated impact stresses present during landing from greater heights. These increased stresses are experienced by supporting tissues like cartilage, ligaments and bones, thus aggravating injury risk. This study sought to investigate frontal plane kinematics, kinetics and energetics of lower extremity joints during landing from different heights. Eighteen male recreational athletes were instructed to perform drop-landing tasks from 0.3- to 0.6-m heights. Force plates and motion-capture system were used to capture ground reaction force and kinematics data, respectively. Joint moment was calculated using inverse dynamics. Joint power was computed as a product of joint moment and angular velocity. Work was defined as joint power integrated over time. Hip and knee joints delivered significantly greater joint power and eccentric work (phip joint in response to increasing landing height. Knee and hip joints acted as key contributors to total energy dissipation in the frontal plane with increase in peak ground reaction force (GRF). The hip joint was the top contributor to energy absorption, which indicated a hip-dominant strategy in the frontal plane in response to peak GRF during landing. Future studies should investigate joint motions that can maximize energy dissipation or reduce the need for energy dissipation in the frontal plane at the various joints, and to evaluate their effects on the attenuation of lower extremity injury risk during landing.
Endo, Tsuyoshi; Uebayashi, Nozomu; Ishida, Satoshi; Ikeuchi, Masahiro; Sato, Fumihiko
2014-08-01
In the field, plants are exposed to fluctuating light, where photosynthesis occurs under conditions far from a steady state. Excess energy dissipation associated with energy quenching of chlorophyll fluorescence (qE) functions as an efficient photo-protection mechanism in photosystem II. PsbS is an important regulator of qE, especially for the induction phase of qE. Beside the regulatory energy dissipation, some part of energy is lost through relaxation of excited chlorophyll molecules. To date, several models to quantify energy loss through these dissipative pathways in PSII have been proposed. In this short review, we compare and evaluate these models for PSII energy allocation when they are applied to non-steady state photosynthesis. As a case study, an investigation on energy allocation to qE-associated dissipation at PSII under non-steady state photosynthesis using PsbS-deficient rice transformants is introduced. Diurnal and seasonal changes in PSII energy allocation in rice under natural light are also presented. Future perspective of studies on PSII energy allocation is discussed. Copyright © 2014 Elsevier Masson SAS. All rights reserved.
Directory of Open Access Journals (Sweden)
Ashour Mohamed A.
2015-03-01
Full Text Available Using energy dissipaters on the soled aprons downstream of head structures is the main technique for accelerating hydraulic jump formation and dissipating a great amount of the residual harmful kinetic energy occurring downstream of head structures. In this paper, an experimental study was conducted to investigate some untested shapes of curved dissipaters with different angles of curvature and arrangements from two points of view. The first is to examine its efficiency in dissipating the kinetic water energy. The second is to examine the most effective shape and arrangement obtained from the aforementioned step in enriching the flow with dissolved oxygen for enhancement of the irrigation water quality. The study was held in the irrigation and hydraulic laboratory of the Civil Department, Faculty of Engineering, Assiut University, using a movable bed tilting channel 20 m long, 30 cm wide, and 50 cm high, using 21 types of curved dissipaters with different arrangements. A total of 660 runs were carried out. Results were analysed, tabulated and graphically presented, and new formulas were introduced to estimate the energy dissipation ratio, as well as the DO concentrations. Results in general showed that the dissipater performance is more tangible in dissipating the residual energy when the curvature is in the opposite direction to that of the flow. Also, the energy loss ratio increases with an increase in curvature angle (θ, until it reaches (θ = 120°, then it decreases again. The study also showed that using three rows of dissipaters give nearly the same effect as using four rows, concerning both the relative energy dissipation and dissolved oxygen content. So, it is recommended to use three rows of the curved dissipater with the angle of curvature (θ = 120° in the opposite direction to that of the flow to obtain the maximum percentage of water energy dissipation downstream of head structures, and maximum dissolved oxygen content too
Carbon nanotubes within polymer matrix can synergistically enhance mechanical energy dissipation
Ashraf, Taimoor; Ranaiefar, Meelad; Khatri, Sumit; Kavosi, Jamshid; Gardea, Frank; Glaz, Bryan; Naraghi, Mohammad
2018-03-01
Safe operation and health of structures relies on their ability to effectively dissipate undesired vibrations, which could otherwise significantly reduce the life-time of a structure due to fatigue loads or large deformations. To address this issue, nanoscale fillers, such as carbon nanotubes (CNTs), have been utilized to dissipate mechanical energy in polymer-based nanocomposites through filler-matrix interfacial friction by benefitting from their large interface area with the matrix. In this manuscript, for the first time, we experimentally investigate the effect of CNT alignment with respect to reach other and their orientation with respect to the loading direction on vibrational damping in nanocomposites. The matrix was polystyrene (PS). A new technique was developed to fabricate PS-CNT nanocomposites which allows for controlling the angle of CNTs with respect to the far-field loading direction (misalignment angle). Samples were subjected to dynamic mechanical analysis, and the damping of the samples were measured as the ratio of the loss to storage moduli versus CNT misalignment angle. Our results defied a notion that randomly oriented CNT nanocomposites can be approximated as a combination of matrix-CNT representative volume elements with randomly aligned CNTs. Instead, our results points to major contributions of stress concentration induced by each CNT in the matrix in proximity of other CNTs on vibrational damping. The stress fields around CNTs in PS-CNT nanocomposites were studied via finite element analysis. Our findings provide significant new insights not only on vibrational damping nanocomposites, but also on their failure modes and toughness, in relation to interface phenomena.
Energy Technology Data Exchange (ETDEWEB)
Uranga-Piña, L. [Facultad de Física, Universidad de la Habana, San Lázaro y L, Vedado, 10400 Havana (Cuba); Institute for Chemistry and Biochemistry, Freie Universität Berlin, Takustr. 3, D-14195 Berlin (Germany); Tremblay, J. C., E-mail: jean.c.tremblay@gmail.com [Institute for Chemistry and Biochemistry, Freie Universität Berlin, Takustr. 3, D-14195 Berlin (Germany)
2014-08-21
We investigate the effect of inter-mode coupling on the vibrational relaxation dynamics of molecules in weak dissipative environments. The simulations are performed within the reduced density matrix formalism in the Markovian regime, assuming a Lindblad form for the system-bath interaction. The prototypical two-dimensional model system representing two CO molecules approaching a Cu(100) surface is adapted from an ab initio potential, while the diatom-diatom vibrational coupling strength is systematically varied. In the weak system-bath coupling limit and at low temperatures, only first order non-adiabatic uni-modal coupling terms contribute to surface-mediated vibrational relaxation. Since dissipative dynamics is non-unitary, the choice of representation will affect the evolution of the reduced density matrix. Two alternative representations for computing the relaxation rates and the associated operators are thus compared: the fully coupled spectral basis, and a factorizable ansatz. The former is well-established and serves as a benchmark for the solution of Liouville-von Neumann equation. In the latter, a contracted grid basis of potential-optimized discrete variable representation is tailored to incorporate most of the inter-mode coupling, while the Lindblad operators are represented as tensor products of one-dimensional operators, for consistency. This procedure results in a marked reduction of the grid size and in a much more advantageous scaling of the computational cost with respect to the increase of the dimensionality of the system. The factorizable method is found to provide an accurate description of the dissipative quantum dynamics of the model system, specifically of the time evolution of the state populations and of the probability density distribution of the molecular wave packet. The influence of intra-molecular vibrational energy redistribution appears to be properly taken into account by the new model on the whole range of coupling strengths. It
Sea spray aerosol and wave energy dissipation in the surf zone
Francius, M.J.; Piazzola, J.; Forget, P.; Calve, O. le; Kusmierczyk-Michulec, J.
2007-01-01
Results from a quantitative model for the prediction of the sea-salt mass flux produced in the surf zone are presented in this paper. The model relates the surf zone sea salt mass flux to the amount of wave energy dissipated in the surf zone. In order to apply this aerosol emission model, a wave
Significant Dissipation of Tidal Energy in the Deep Ocean Inferred from Satellite Altimeter Data
Egbert, G. D.; Ray, R. D.
2000-01-01
How and where the ocean tides dissipate their energy are longstanding questions that have consequences ranging from the history of the Moon to the mixing of the oceans. Historically, the principal sink of tidal energy has been thought to be bottom friction in shallow seas. There has long been suggestive however, that tidal dissipation also occurs in the open ocean through the scattering by ocean-bottom topography of surface tides into internal waves, but estimates of the magnitude of this possible sink have varied widely. Here we use satellite altimeter data from Topex/Poseidon to map empirically the tidal energy dissipation. We show that approximately 10(exp 12) watts-that is, 1 TW, representing 25-30% of the total dissipation-occurs in the deep ocean, generally near areas of rough topography. Of the estimated 2 TW of mixing energy required to maintain the large-scale thermohaline circulation of the ocean, one-half could therefore be provided by the tides, with the other half coming from action on the surface of the ocean.
Dissipation of solar energy in landscape - controlled by management of water and vegetation
Czech Academy of Sciences Publication Activity Database
Pokorný, Jan
2001-01-01
Roč. 24, - (2001), s. 641-645 ISSN 0960-1481 R&D Projects: GA AV ČR KSK6005114 Institutional research plan: CEZ:AV0Z6005908 Keywords : Solar energy dissipation * vegetation * production -evapotranspiration Subject RIV: DA - Hydrology ; Limnology Impact factor: 0.224, year: 2001
Seismic energy dissipation study of linear fluid viscous dampers in steel structure design
Directory of Open Access Journals (Sweden)
A. Ras
2016-09-01
Full Text Available Energy dissipation systems in civil engineering structures are sought when it comes to removing unwanted energy such as earthquake and wind. Among these systems, there is combination of structural steel frames with passive energy dissipation provided by Fluid Viscous Dampers (FVD. This device is increasingly used to provide better seismic protection for existing as well as new buildings and bridges. A 3D numerical investigation is done considering the seismic response of a twelve-storey steel building moment frame with diagonal FVD that have linear force versus velocity behaviour. Nonlinear time history, which is being calculated by Fast nonlinear analysis (FNA, of Boumerdes earthquake (Algeria, May 2003 is considered for the analysis and carried out using the SAP2000 software and comparisons between unbraced, braced and damped structure are shown in a tabulated and graphical format. The results of the various systems are studied to compare the structural response with and without this device of the energy dissipation thus obtained. The conclusions showed the formidable potential of the FVD to improve the dissipative capacities of the structure without increasing its rigidity. It is contributing significantly to reduce the quantity of steel necessary for its general stability.
Assessment of Stability and Energy Dissipation Performances of an Antifer Layer Protected Caisson
Directory of Open Access Journals (Sweden)
M. Sedat Kabdaşlı
2015-08-01
Full Text Available The present study intends to assess the stability and energy dissipation performances of a breakwater configuration (APC protected by an antifer layer. For comparison, an ordinary caisson (OC, which was 5% wider and 10% heavier, was also investigated. Physical models were implemented and tested under regular and irregular waves; and resulting linear and angular displacements were directly measured via a photogrammetric method. Additionally, wave forces and resulting horizontal displacements were estimated both from recorded pressure data and from individual incident waves by modified Goda method. To calculate the horizontal displacement, the estimated wave force time series were directly double-integrated, whilst the theoretical method proposed by Shimosako et al. (1994 were used on the individual force values. Although OC was tested under shorter durations and had a more favorable superstructure in terms of resisting forces, the results indicated that APC was significantly more stable. Energy dissipation performance of the tested configurations were quantified in terms of spectral averaged and phase resolved reflection coefficients, whereas antifer damage ratio was measured on a block-count basis. Results indicated that the APC configuration had an enhanced performance of dissipating the wave energy; moreover, the dissipated energy directly links to antifer damage ratio.
Directory of Open Access Journals (Sweden)
Maxim Olegovich Korpusov
2012-07-01
Full Text Available In this article the initial-boundary-value problem for generalized dissipative high-order equation of Klein-Gordon type is considered. We continue our study of nonlinear hyperbolic equations and systems with arbitrary positive energy. The modified concavity method by Levine is used for proving blow-up of solutions.
Wave Energy Dissipation of Waves Breaking on a Reef with a Steep Front Slope
DEFF Research Database (Denmark)
Jensen, M.S.; Burcharth, Hans F.; Brorsen, Michael
2005-01-01
The Transformation of waves propagating over a steep bottom slope is of great importance regarding the coastal processes in the near-shore area.This study will contribute with tools to predict the dissipated wave energy for irregular waves passing a steep submerged slope. An extensive number of t...
Energy dissipation from a correlated system driven out of equilibrium.
Rameau, J D; Freutel, S; Kemper, A F; Sentef, M A; Freericks, J K; Avigo, I; Ligges, M; Rettig, L; Yoshida, Y; Eisaki, H; Schneeloch, J; Zhong, R D; Xu, Z J; Gu, G D; Johnson, P D; Bovensiepen, U
2016-12-20
In complex materials various interactions have important roles in determining electronic properties. Angle-resolved photoelectron spectroscopy (ARPES) is used to study these processes by resolving the complex single-particle self-energy and quantifying how quantum interactions modify bare electronic states. However, ambiguities in the measurement of the real part of the self-energy and an intrinsic inability to disentangle various contributions to the imaginary part of the self-energy can leave the implications of such measurements open to debate. Here we employ a combined theoretical and experimental treatment of femtosecond time-resolved ARPES (tr-ARPES) show how population dynamics measured using tr-ARPES can be used to separate electron-boson interactions from electron-electron interactions. We demonstrate a quantitative analysis of a well-defined electron-boson interaction in the unoccupied spectrum of the cuprate Bi 2 Sr 2 CaCu 2 O 8+x characterized by an excited population decay time that maps directly to a discrete component of the equilibrium self-energy not readily isolated by static ARPES experiments.
Computational model for noncontact atomic force microscopy: energy dissipation of cantilever.
Senda, Yasuhiro; Blomqvist, Janne; Nieminen, Risto M
2016-09-21
We propose a computational model for noncontact atomic force microscopy (AFM) in which the atomic force between the cantilever tip and the surface is calculated using a molecular dynamics method, and the macroscopic motion of the cantilever is modeled by an oscillating spring. The movement of atoms in the tip and surface is connected with the oscillating spring using a recently developed coupling method. In this computational model, the oscillation energy is dissipated, as observed in AFM experiments. We attribute this dissipation to the hysteresis and nonconservative properties of the interatomic force that acts between the atoms in the tip and sample surface. The dissipation rate strongly depends on the parameters used in the computational model.
Energy dissipation in non-isothermal molecular dynamics simulations of confined liquids under shear.
Berro, Hassan; Fillot, Nicolas; Vergne, Philippe; Tokumasu, Takashi; Ohara, Taku; Kikugawa, Gota
2011-10-07
Energy is commonly dissipated in molecular dynamics simulations by using a thermostat. In non-isothermal shear simulations of confined liquids, the choice of the thermostat is very delicate. We show in this paper that under certain conditions, the use of classical thermostats can lead to an erroneous description of the dynamics in the confined system. This occurs when a critical shear rate is surpassed as the thermo-viscous effects become prominent. In this high-shear-high-dissipation regime, advanced dissipation methods including a novel one are introduced and compared. The MD results show that the physical modeling of both the accommodation of the surface temperature to liquid heating and the heat conduction through the confining solids is essential. The novel method offers several advantages on existing ones including computational efficiency and easiness of application for complex systems. © 2011 American Institute of Physics
Idarraga Alarcon, G.A.; Burgelman, N.D.M.; Meza Meza, J.; Toro, A.; Li, Z.
2015-01-01
This work investigates the energy dissipation in a wheel/rail system through friction work modeling. In order to identify the effect of the friction coefficient on the energy dissipation in the wheel/rail contact, several simulations were performed using a 3D multibody model of a railway vehicle
Pulsatile blood flow, shear force, energy dissipation and Murray's Law
Directory of Open Access Journals (Sweden)
Bengtsson Hans-Uno
2006-08-01
Full Text Available Abstract Background Murray's Law states that, when a parent blood vessel branches into daughter vessels, the cube of the radius of the parent vessel is equal to the sum of the cubes of the radii of daughter blood vessels. Murray derived this law by defining a cost function that is the sum of the energy cost of the blood in a vessel and the energy cost of pumping blood through the vessel. The cost is minimized when vessel radii are consistent with Murray's Law. This law has also been derived from the hypothesis that the shear force of moving blood on the inner walls of vessels is constant throughout the vascular system. However, this derivation, like Murray's earlier derivation, is based on the assumption of constant blood flow. Methods To determine the implications of the constant shear force hypothesis and to extend Murray's energy cost minimization to the pulsatile arterial system, a model of pulsatile flow in an elastic tube is analyzed. A new and exact solution for flow velocity, blood flow rate and shear force is derived. Results For medium and small arteries with pulsatile flow, Murray's energy minimization leads to Murray's Law. Furthermore, the hypothesis that the maximum shear force during the cycle of pulsatile flow is constant throughout the arterial system implies that Murray's Law is approximately true. The approximation is good for all but the largest vessels (aorta and its major branches of the arterial system. Conclusion A cellular mechanism that senses shear force at the inner wall of a blood vessel and triggers remodeling that increases the circumference of the wall when a shear force threshold is exceeded would result in the observed scaling of vessel radii described by Murray's Law.
Photoprotection in an ecological context: the remarkable complexity of thermal energy dissipation.
Demmig-Adams, Barbara; Adams, William W
2006-01-01
This review places photoprotection into the context of ecology and species diversity. The focus is on photoprotection via the safe removal - as thermal energy - of excess solar energy absorbed by the light collecting system, which counteracts the formation of reactive oxygen species. An update on the surprisingly complex, multiple variations of thermal energy dissipation is presented, placing these different forms into ecological and genetic contexts. Zeaxanthin-facilitated, flexible thermal dissipation associated with the PsbS protein and controlled by the trans-thylakoid pH gradient apparently occurs ubiquitously in plants, and can become sustained (and thus less flexible) at low temperatures. Long-lived, slow-growing plants with low intrinsic capacities for photosynthesis have greater capacities for this flexible dissipation than short-lived, fast-growing species. Furthermore, potent, but inflexible (zeaxanthin-facilitated) thermal dissipation, prominent in evergreen species under prolonged environmental stress, is characterized with respect to the involvement of photosystem II core rearrangement and/or degradation as well as the absence of control by trans-thylakoid pH and, possibly, PsbS. A role of PsbS-related proteins in photoprotection is discussed.
Energy dissipation and fluctuations in a driven liquid.
Del Junco, Clara; Tociu, Laura; Vaikuntanathan, Suriyanarayanan
2018-03-16
Minimal models of active and driven particles have recently been used to elucidate many properties of nonequilibrium systems. However, the relation between energy consumption and changes in the structure and transport properties of these nonequilibrium materials remains to be explored. We explore this relation in a minimal model of a driven liquid that settles into a time periodic steady state. Using concepts from stochastic thermodynamics and liquid state theories, we show how the work performed on the system by various nonconservative, time-dependent forces-this quantifies a violation of time reversal symmetry-modifies the structural, transport, and phase transition properties of the driven liquid.
Energy method for multi-dimensional balance laws with non-local dissipation
Duan, Renjun
2010-06-01
In this paper, we are concerned with a class of multi-dimensional balance laws with a non-local dissipative source which arise as simplified models for the hydrodynamics of radiating gases. At first we introduce the energy method in the setting of smooth perturbations and study the stability of constants states. Precisely, we use Fourier space analysis to quantify the energy dissipation rate and recover the optimal time-decay estimates for perturbed solutions via an interpolation inequality in Fourier space. As application, the developed energy method is used to prove stability of smooth planar waves in all dimensions n2, and also to show existence and stability of time-periodic solutions in the presence of the time-periodic source. Optimal rates of convergence of solutions towards the planar waves or time-periodic states are also shown provided initially L1-perturbations. © 2009 Elsevier Masson SAS.
Local Turbulent Energy Dissipation Rate in a Vessel Agitated by a Rushton Turbine
Directory of Open Access Journals (Sweden)
Šulc Radek
2015-06-01
Full Text Available The scaling of turbulence characteristics such as turbulent fluctuation velocity, turbulent kinetic energy and turbulent energy dissipation rate was investigated in a mechanically agitated vessel 300 mm in inner diameter stirred by a Rushton turbine at high Reynolds numbers in the range 50 000 < Re < 100 000. The hydrodynamics and flow field was measured using 2-D TR PIV. The convective velocity formulas proposed by Antonia et al. (1980 and Van Doorn (1981 were tested. The turbulent energy dissipation rate estimated independently in both radial and axial directions using the one-dimensional approach was not found to be the same in each direction. Using the proposed correction, the values in both directions were found to be close to each other. The relation ε/(N3·D2 ∞ const. was not conclusively confirmed.
Sap flow is Underestimated by Thermal Dissipation Sensors due to Alterations of Wood Anatomy
Marañón-Jiménez, S.; Wiedemann, A.; van den Bulcke, J.; Cuntz, M.; Rebmann, C.; Steppe, K.
2014-12-01
The thermal dissipation technique (TD) is one of the most commonly adopted methods for sap flow measurements. However, underestimations of up to 60% of the tree transpiration have been reported with this technique, although the causes are not certainly known. The insertion of TD sensors within the stems causes damage of the wood tissue and subsequent healing reactions, changing wood anatomy and likely the sap flow path. However, the anatomical changes in response to the insertion of sap flow sensors and the effects on the measured flow have not been assessed yet. In this study, we investigate the alteration of vessel anatomy on wounds formed around TD sensors. Our main objectives were to elucidate the anatomical causes of sap flow underestimation for ring-porous and diffuse-porous species, and relate these changes to sap flow underestimations. Successive sets of TD probes were installed in early, mid and end of the growing season in Fagus sylvatica (diffuse-porous) and Quercus petraea (ring-porous) trees. They were logged after the growing season and additional sets of sensors were installed in the logged stems with presumably no healing reaction. The wood tissue surrounding each sensor was then excised and analysed by X-ray computed microtomography (X-ray micro CT). This technique allowed the quantification of vessel anatomical characteristics and the reconstruction of the 3-D internal microstructure of the xylem vessels so that extension and shape of the altered area could be determined. Gels and tyloses clogged the conductive vessels around the sensors in both beech and oak. The extension of the affected area was larger for beech although these anatomical changes led to similar sap flow underestimations in both species. The higher vessel size in oak may explain this result and, therefore, larger sap flow underestimation per area of affected conductive tissue. The wound healing reaction likely occurred within the first weeks after sensor installation, which
Heber, Ulrich; Soni, Vineet; Strasser, Reto J
2011-05-01
During desiccation, fluorescence emission and stable light-dependent charge separation in the reaction centers (RCs) of photosystem II (PSII) declined strongly in three different lichens: in Parmelia sulcata with an alga as the photobiont, in Peltigera neckeri with a cyanobacterium and in the tripartite lichen Lobaria pulmonaria. Most of the decline of fluorescence was caused by a decrease in the quantum efficiency of fluorescence emission. It indicated the activation of photoprotective thermal energy dissipation. Photochemical activity of the RCs was retained even after complete desiccation. It led to light-dependent absorption changes and found expression in reversible increases in fluorescence or in fluorescence quenching. Lowering the temperature changed the direction of fluorescence responses in P. sulcata. The observations are interpreted to show that reversible light-induced increases in fluorescence emission in desiccated lichens indicate the functionality of the RCs of PSII. Photoprotection is achieved by the drainage of light energy to dissipating centers outside the RCs before stable charge separation can take place. Reversible quenching of fluorescence by strong illumination is suggested to indicate the conversion of the RCs from energy conserving to energy dissipating units. This permits them to avoid photoinactivation. On hydration, re-conversion occurs to energy-conserving RCs. Copyright © Physiologia Plantarum 2010.
Adams, W W; Demmig-Adams, B; Rosenstiel, T N; Ebbert, V
2001-01-01
Two very distinctive responses of photosynthesis to winter conditions have been identified. Mesophytic species that continue to exhibit growth during the winter typically exhibit higher maximal rates of photosynthesis during the winter or when grown at lower temperatures compared to individuals examined during the summer or when grown at warmer temperatures. In contrast, sclerophytic evergreen species growing in sun-exposed sites typically exhibit lower maximal rates of photosynthesis in the winter compared to the summer. On the other hand, shaded individuals of those same sclerophytic evergreen species exhibit similar or higher maximal rates of photosynthesis in the winter compared to the summer. Employment of the xanthophyll cycle in photoprotective energy dissipation exhibits similar characteristics in the two groups of plants (mesophytes and shade leaves of sclerophytic evergreens) that exhibit upregulation of photosynthesis during the winter. In both, zeaxanthin + antheraxanthin (Z + A) are retained and PS II remains primed for energy dissipation only on nights with subfreezing temperatures, and this becomes rapidly reversed upon exposure to increased temperatures. In contrast, Z + A are retained and PS II remains primed for energy dissipation over prolonged periods during the winter in sun leaves of sclerophytic evergreen species, and requires days of warming to become fully reversed. The rapid disengagement of this energy dissipation process in the mesophytes and shade sclerophytes apparently permits a rapid return to efficient photosynthesis and increased activity on warmer days during the winter. This may be associated with a decreasing opportunity for photosynthesis in source leaves relative to the demand for photosynthesis in the plant's sinks. In contrast, the sun-exposed sclerophytes - with a relatively high source to sink ratio - maintain PS II in a state primed for high levels of energy dissipation activity throughout much of the winter. Independent
A new permanent magnetic friction damper device for passive energy dissipation
International Nuclear Information System (INIS)
Dai, Hongzhe; Wang, Wei; Huang, Zuojian
2014-01-01
This paper summarizes the development of a new permanent magnetic friction damper (PMFD) device designed to protect structures during earthquakes. The device is based on the concept that when two permanent magnetic strips are osculated, magnetic attraction is produced and the magnitude can be adjusted and predicted by changing the area of the contact surface of the strips. Thus, the controlling force of the PMFD device varies continuously with the response of the structure and thereby overcomes the drawbacks of conventional friction dampers, the force models for which are invariable. We performed shaking table tests and numerical studies for a five-story steel frame structure fitted with PMFD devices; the results demonstrate that the new device effectively reduces the seismic response of a structure due to its excellent energy dissipation capacity. Moreover, the controlling force supplied by the new PMFD device can be adaptively adjusted according to the magnitude of the excitations. Therefore, the new PMFD device presents a viable alternative to conventional friction-based earthquake-resistant designs both for new construction and for upgrading existing structures. (paper)
Kuzminov, Fedor I; Gorbunov, Maxim Y
2016-02-01
To prevent photooxidative damage under supraoptimal light, photosynthetic organisms evolved mechanisms to thermally dissipate excess absorbed energy, known as non-photochemical quenching (NPQ). Here we quantify NPQ-induced alterations in light-harvesting processes and photochemical reactions in Photosystem 2 (PS2) in the pennate diatom Phaeodactylum tricornutum. Using a combination of picosecond lifetime analysis and variable fluorescence technique, we examined the dynamics of NPQ activation upon transition from dark to high light. Our analysis revealed that NPQ activation starts with a 2-3-fold increase in the rate constant of non-radiative charge recombination in the reaction center (RC); however, this increase is compensated with a proportional increase in the rate constant of back reactions. The resulting alterations in photochemical processes in PS2 RC do not contribute directly to quenching of antenna excitons by the RC, but favor non-radiative dissipation pathways within the RC, reducing the yields of spin conversion of the RC chlorophyll to the triplet state. The NPQ-induced changes in the RC are followed by a gradual ~ 2.5-fold increase in the yields of thermal dissipation in light-harvesting complexes. Our data suggest that thermal dissipation in light-harvesting complexes is the major sink for NPQ; RCs are not directly involved in the NPQ process, but could contribute to photoprotection via reduction in the probability of (3)Chl formation.
Energy dissipation by whistler turbulence: Three-dimensional particle-in-cell simulations
Energy Technology Data Exchange (ETDEWEB)
Chang, Ouliang, E-mail: ouliang@usc.edu [Oracle Corporation, Redwood City, California 94065 (United States); Peter Gary, S., E-mail: pgary@lanl.gov [Space Science Institute, Boulder, Colorado (United States); Wang, Joseph, E-mail: josephjw@usc.edu [University of Southern California, Los Angeles, California (United States)
2014-05-15
Three-dimensional particle-in-cell simulations of whistler turbulence are carried out on a collisionless, homogeneous, magnetized plasma model. The simulations use an initial ensemble of relatively long wavelength whistler modes and follow the temporal evolution of the fluctuations as they cascade into a broadband, anisotropic, turbulent spectrum at shorter wavelengths. For relatively small levels of the initial fluctuation energy ϵ{sub e}, linear collisionless damping provides most of the dissipation of the turbulence. But as ϵ{sub e} and the total dissipation increase, linear damping becomes less important and, especially at β{sub e} ≪ 1, nonlinear processes become stronger. The PDFs and kurtoses of the magnetic field increments in the simulations suggest that intermittency in whistler turbulence generally increases with increasing ϵ{sub e} and β{sub e}. Correlation coefficient calculations imply that the current structure dissipation also increases with increasing ϵ{sub e} and β{sub e}, and that the nonlinear dissipation processes in these simulations are primarily associated with regions of localized current structures.
Energy dissipation by whistler turbulence: Three-dimensional particle-in-cell simulations
International Nuclear Information System (INIS)
Chang, Ouliang; Peter Gary, S.; Wang, Joseph
2014-01-01
Three-dimensional particle-in-cell simulations of whistler turbulence are carried out on a collisionless, homogeneous, magnetized plasma model. The simulations use an initial ensemble of relatively long wavelength whistler modes and follow the temporal evolution of the fluctuations as they cascade into a broadband, anisotropic, turbulent spectrum at shorter wavelengths. For relatively small levels of the initial fluctuation energy ϵ e , linear collisionless damping provides most of the dissipation of the turbulence. But as ϵ e and the total dissipation increase, linear damping becomes less important and, especially at β e ≪ 1, nonlinear processes become stronger. The PDFs and kurtoses of the magnetic field increments in the simulations suggest that intermittency in whistler turbulence generally increases with increasing ϵ e and β e . Correlation coefficient calculations imply that the current structure dissipation also increases with increasing ϵ e and β e , and that the nonlinear dissipation processes in these simulations are primarily associated with regions of localized current structures
International Nuclear Information System (INIS)
Gritsenko, I.A.; Klokol, K.A.; Sokolov, S.S.; Sheshin, G.A.
2016-01-01
An experimental study is made of the drag coefficient, which is the characteristics of energy dissipation during oscillations of the tuning forks, immersed in liquid helium. The experiments were performed in the temperature range from 0.1 to 3.5 K covering both the range of a hydrodynamic flow, and the ballistic regime of transfer of thermal excitations of superfluid helium below 0.6 K. It is found that there is the frequency dependence of the drag coefficient in the hydrodynamic limit, when the main dissipation mechanism is the viscous friction of the fluid against the walls of the oscillating body at temperatures above 0.7 K. In this case, the drag coefficient is proportional to the square root of the frequency of oscillation, and its temperature dependence in He II is determined by the respective dependence of the normal component density of the normal component and the viscosity of the fluid. At lower temperatures, the dependence of drag coefficient on the frequency is not available, and the magnitude of the dissipative losses is determined only by the temperature dependence of the density of the normal component. At the same time in the entire range of temperatures value of dissipative losses depends on the geometry of the oscillating body.
International Nuclear Information System (INIS)
Sernelius, Bo E
2008-01-01
The energy spectrum of electromagnetic normal modes plays a central role in the theory of the van der Waals and Casimir interaction. Here we study the modes in connection with the van der Waals interaction between two metal half spaces. Neglecting dissipation leads to distinct normal modes with real-valued frequencies. Including dissipation seems to have the effect that these distinct modes move away from the real axis into the complex frequency plane. The summation of the zero-point energies of these modes render a complex-valued result. Using the contour integration, resulting from the use of the generalized argument principle, gives a real-valued and different result. We resolve this contradiction and show that the spectrum of true normal modes forms a continuum with real frequencies
Hydraulics, Air Entrainment, and Energy Dissipation on a Gabion Stepped Weir
Wüthrich, Davide; Chanson, Hubert
2014-01-01
In the last decades the design of stepped spillways regained some interest because of their suitability with new construction methods including gabions. The hydraulic performances of gabion stepped weirs were investigated experimentally in terms of the flow patterns, air-water flow properties, and energy dissipation. A laboratory study was conducted in a 26.6 degrees slope (1V: 2H) and 0.10-m step height facility, with both smooth impervious and gabion steps. The visual observations highlight...
International Nuclear Information System (INIS)
Agre, M.Ya.
1996-01-01
A compact expression for the cross section of light scattering by aligned atomic systems is derived. It is shown that in above-threshold or resonant scattering, when the channel of luminous energy dissipation is open, circular dichroism effects can be observed in the angular distribution and the degree of polarization of the scattered light. In such cases circular polarization of the scattered light is also induced when the incident light has no circular polarization
Directory of Open Access Journals (Sweden)
T. Kubina
2013-07-01
Full Text Available Energy dissipation and areas of process instability were investigated in two alloys. The first one was brass, the second one was the steel 9 Cr (P91. The tests were performed on torsion plastometer Setaram and on compression plastometer Gleeble. In the case of the steel 9 Cr identical heat was tested on both plastometers. The resulting 2D or 3D process maps indicate suitable areas of forming temperatures, magnitudes of deformation and strain rates.
Molecular scale energy dissipation in oligothiophene monolayers measured by dynamic force microscopy
Energy Technology Data Exchange (ETDEWEB)
Martinez, Nicolas F; Gomez, Carlos J; Garcia, Ricardo [CSIC-Instituto de Microelectronica de Madrid (IMM), Isaac Newton 8, E-28760 Tres Cantos, Madrid (Spain); Kaminski, Wojciech [Institute of Experimental Physics, University of Wroclaw, plac Maksa Borna 9, PL-50-204 Wroclaw (Poland); Albonetti, Cristiano; Biscarini, Fabio [CNR-Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Via P Gobetti 101, I-40129 Bologna (Italy); Perez, Ruben, E-mail: ruben.perez@uam.e, E-mail: rgarcia@imm.cnm.csic.e [Departamento de Fisica Teorica de la Materia Condensada, Universidad Autonoma de Madrid, E-28049 Madrid (Spain)
2009-10-28
We perform a combined experimental and theoretical approach to establish the atomistic origin of energy dissipation occurring while imaging a molecular surface with an amplitude modulation atomic force microscope. We show that the energy transferred by a single nano-asperity to a sexithiophene monolayer is about 0.15 eV/cycle. The configuration space sampled by the tip depends on whether it approaches or withdraws from the surface. The asymmetry arises because of the presence of energy barriers among different deformations of the molecular geometry. This is the source of the material contrast provided by the phase-shift images.
Li, Ling; Ortiz, Christine
2014-05-01
Hierarchical composite materials design in biological exoskeletons achieves penetration resistance through a variety of energy-dissipating mechanisms while simultaneously balancing the need for damage localization to avoid compromising the mechanical integrity of the entire structure and to maintain multi-hit capability. Here, we show that the shell of the bivalve Placuna placenta (~99 wt% calcite), which possesses the unique optical property of ~80% total transmission of visible light, simultaneously achieves penetration resistance and deformation localization via increasing energy dissipation density (0.290 ± 0.072 nJ μm-3) by approximately an order of magnitude relative to single-crystal geological calcite (0.034 ± 0.013 nJ μm-3). P. placenta, which is composed of a layered assembly of elongated diamond-shaped calcite crystals, undergoes pervasive nanoscale deformation twinning (width ~50 nm) surrounding the penetration zone, which catalyses a series of additional inelastic energy dissipating mechanisms such as interfacial and intracrystalline nanocracking, viscoplastic stretching of interfacial organic material, and nanograin formation and reorientation.
Zhou, Fulin; Tan, Ping
2018-01-01
China is a country where 100% of the territory is located in a seismic zone. Most of the strong earthquakes are over prediction. Most fatalities are caused by structural collapse. Earthquakes not only cause severe damage to structures, but can also damage non-structural elements on and inside of facilities. This can halt city life, and disrupt hospitals, airports, bridges, power plants, and other infrastructure. Designers need to use new techniques to protect structures and facilities inside. Isolation, energy dissipation and, control systems are more and more widely used in recent years in China. Currently, there are nearly 6,500 structures with isolation and about 3,000 structures with passive energy dissipation or hybrid control in China. The mitigation techniques are applied to structures like residential buildings, large or complex structures, bridges, underwater tunnels, historical or cultural relic sites, and industrial facilities, and are used for retrofitting of existed structures. This paper introduces design rules and some new and innovative devices for seismic isolation, energy dissipation and hybrid control for civil and industrial structures. This paper also discusses the development trends for seismic resistance, seismic isolation, passive and active control techniques for the future in China and in the world.
Observations of Thin Current Sheets in the Solar Wind and Their Role in Magnetic Energy Dissipation
Perri, S.; Goldstein, M. L.; Dorelli, J.; Sahraoui, F.; Gurgiolo, C. A.; Karimabadi, H.; Mozer, F.; Wendel, D. E.; TenBarge, J.; Roytershteyn, V.
2013-12-01
A recent analysis of 450 vec/s resolution data from the STAFF search-coil magnetometer on board Cluster has revealed, for the first time, the presence of thin current sheets and discontinuities from the proton Larmor scale down to the electron Larmor scale in the solar wind. This is in the range of scales where a cascade of energy consistent with highly oblique kinetic Alfvénic fluctuations (KAW), eventually dissipated by electron Landau damping, has been detected. The current sheets have been found to have a size between 20-200 km, indicating that they are very localized. We will compare the observations with results coming from 2D Hall MHD, Gyrokinetic, and full Particle-in-Cell turbulence simulations. Preliminary work has highlighted promising qualitative agreement between the properties of the structures observed in the Cluster data and the current sheets generated in the simulations. With the aim of investigating the role played by those structures in dissipating the magnetic energy in the solar wind, E●J has been computed within each magnetic discontinuity. This has been made possible via a combined analysis of both STAFF-SC magnetic field data and the electric field data from the Electric Fields and Wave instrument (EFW). We describe procedures used to reduce the noise in the EFW data. The results obtained represent an effort to clarify the processes involved in the dissipation of magnetic energy in the solar wind.
Heber, Ulrich
2012-09-01
Conservation of light energy in photosynthesis is possible only in hydrated photoautotrophs. It requires complex biochemistry and is limited in capacity. Charge separation in reaction centres of photosystem II initiates energy conservation but opens also the path to photooxidative damage. A main mechanism of photoprotection active in hydrated photoautotrophs is controlled by light. This is achieved by coupling light flux to the protonation of a special thylakoid protein which activates thermal energy dissipation. This mechanism facilitates the simultaneous occurrence of energy conservation and energy dissipation but cannot completely prevent damage by light. Continuous metabolic repair is required to compensate damage. More efficient photoprotection is needed by desiccation-tolerant photoautotrophs. Loss of water during desiccation activates ultra-fast energy dissipation in mosses and lichens. Desiccation-induced energy dissipation neither requires a protonation reaction nor light but photoprotection often increases when light is present during desiccation. Two different mechanisms contribute to photoprotection of desiccated photoautotrophs. One facilitates energy dissipation in the antenna of photosystem II which is faster than energy capture by functional reaction centres. When this is insufficient for full photoprotection, the other one permits energy dissipation in the reaction centres themselves.
Energy Technology Data Exchange (ETDEWEB)
Yoon, Hong Min [Department of Mechanical Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Kondaraju, Sasidhar [Department of Mechanical Science, Indian Institute of Technology Bhubaneswar, Bhubaneswar, Odisha 751013 (India); Lee, Jung Shin [Department of Mechanical Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Suh, Youngho; Lee, Joonho H. [Samsung Electronics, Mechatronics R& D Center, Hwaseong-si, Gyeonggi-do 445-330 (Korea, Republic of); Lee, Joon Sang, E-mail: joonlee@yonsei.ac.kr [Department of Mechanical Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)
2017-07-01
Highlights: • Contact line forces, including friction and spreading forces are directly calculated. • Overall trends of variations in contact line forces during droplet spreading process show characteristics of contact line forces. • Detail relations of contact line forces and atomic kinetics in the contact line provide a clear evidence of the possible energy dissipation mechanism in droplet spreading process. - Abstract: Recent studies have revealed that contact line forces play an important role in the droplet spreading process. Despite their significance, the physics related to them has been studied only indirectly and the effect of contact line forces is still being disputed. We performed a molecular dynamics simulation and mimicked the droplet spreading process at the nanoscale. Based on the results of the simulation, the contact line forces were directly calculated. We found that the forces acting on the bulk and the contact line region showed different trends. Distinct positive and negative forces, contact line spreading, and friction forces were observed near the contact line. We also observed a strong dependency of the atomic kinetics in the contact line region on the variations in the contact line forces. The atoms of the liquid in the contact line region lost their kinetic energy due to the contact line friction force and became partially immobile on the solid surface. The results of the current study will be useful for understanding the role of the contact line forces on the kinetic energy dissipation in the contact line region.
Energy dissipation in the process of ternary fission in heavy nuclear reaction
International Nuclear Information System (INIS)
Li Xian; Wang Chengqian; Yan Shiwei
2015-01-01
We studied the evolution of the collective motion, interaction potential, the total kinetic and excitation energies in ternary fissions of 197 Au + 197 Au system at 15 MeV/u, and discussed energy dissipation of this reaction. Through the comparison with energy-angle correlation data in binary fissions, we preliminarily concluded that the rst fission of ternary fission was an extreme deep-inelastic process. We further analyzed the correlation of the total kinetic energy with impact parameters in both binary and ternary reactions, and found that the total energy of binary reactions systems was lost about 150 MeV more than ternary fission with small impact parameters, and with larger impact parameters the total energy of ternary reactions were lost 300 MeV more than binary reactions. (authors)
Free energy dissipation of the spontaneous gating of a single voltage-gated potassium channel
Wang, Jia-Zeng; Wang, Rui-Zhen
2018-02-01
Potassium channels mainly contribute to the resting potential and re-polarizations, with the potassium electrochemical gradient being maintained by the pump Na+/K+-ATPase. In this paper, we construct a stochastic model mimicking the kinetics of a potassium channel, which integrates temporal evolving of the membrane voltage and the spontaneous gating of the channel. Its stationary probability density functions (PDFs) are found to be singular at the boundaries, which result from the fact that the evolving rates of voltage are greater than the gating rates of the channel. We apply PDFs to calculate the power dissipations of the potassium current, the leakage, and the gating currents. On a physical perspective, the essential role of the system is the K+-battery charging the leakage (L-)battery. A part of power will inevitably be dissipated among the process. So, the efficiency of energy transference is calculated.
Evaluating a flash size and energy dissipation relationship through various modeling techniques
Salinas, V.; Brothers, M.; Bruning, E. C.; Mansell, E.
2017-12-01
Many studies have investigated the influence of the electrostatic and kinematic environments of thunderstorms on lightning flash size. Recent work has demonstrated a coupling of turbulent kinematic properties to flash size distribution in different regions of a storm. Additional work has also theorized a relationship of flash size and energy to the TKE spectrum. However, the physical basis for using flash size alone in these estimates remains absent. This study used the National Severe Storms Laboratory's Collaborative Model for Multiscale Atmospheric Simulation model (N-COMMAS) to simulate an observed multicellular thunderstorm to investigate the relationship between flash size and energy. Model output included the total energy dissipated for each flash, and the charge, electric potential, electric field where it propagated. These flashes were then modeled in two simplified ways. First, each flash was assumed to be convex hull volumes of charge. A 3D Poisson solver was then used on each charge volume for charge density retrieval and computation of the electric potential, using a theoretical electric field breakeven threshold and charge conservation. Second, a capacitor model was used to estimate the energy dissipated using flash area, charge, and plate spacing obtained from the COMMAS model. These two calculations of flash energy were compared to the COMMAS energy. The results suggested that flash size alone was insufficient in characterizing the energetic properties.
Czech Academy of Sciences Publication Activity Database
Kopecký, Jiří; Azarkovich, M.; Schuvalov, V. A.; Heber, U.
2005-01-01
Roč. 7, - (2005), s. 1-13 ISSN 1435-8603 Institutional research plan: CEZ:AV0Z50200510 Keywords : chlorophyll fluorescence * energy dissipation * lichens Subject RIV: EE - Microbiology, Virology Impact factor: 1.910, year: 2005
Hao, Xiang; Chen, Liang; Sang, Wei
2018-01-01
Abstract Living systems can experience time‐dependent dynamic self‐assembly for periodic, adaptive behavior via energy dissipation pathway. Creating in vitro mimics is a daunting mission. Here a “living” giant vesicle system that can perform a periodic pulsating motion using adenosine‐5'‐triphosphate (ATP)‐fuelled dissipative self‐assembly is described. This dynamic system is built on transient supramolecular interactions between the polymer and cellular energy currency ATP. The vesicles capturing ATPs will deviate away from equilibrium, leading to an energy ascent that drives a continuous vesicular expansion, until a competitive ATP hydrolysis predominates to break the ATP–polymer interactions and deplete the energy stored in the vesicles, leading to an opposing vesicular contraction. The input of ATP energy can sustain that these vesicles run periodically along this reciprocating expansile–contractile process, resembling a “pulsating” behavior. ATP level can orchestrate the rhythm, amplitude, and lifetime of this biomimetic pulsation. By pre‐programming the ATP stimulation protocol, this kind of adaptive microcapsules can function as high‐performance microseparators to perform size‐selective sieving of different nanoparticles through ATP‐mediated transmembrane traffic. This man‐made system offers a primitive model of time‐dependent dynamic self‐assembly and may offer new ways to build life‐like materials with biomimetic functions.
Samolov, Ana; Popovic, Svetozar; Vuskovic, Leposava; Basovic, Milos; Cuckov, Filip; Raitses, Yevgeny; Kaganovich, Igor
2013-09-01
Electron-induced Secondary Electron Emission (SEE) is important in many gas discharge applications such as Hall thrusters, surface and multipactor discharges. Often they present the inhibiting phenomena in designing and operating of these systems, examples being the Superconducting Radio Frequency (SRF) accelerator cavities. The multipactor discharges depend on the resonant field configuration and on the SEE from the cavity surface. SEE is proportional to the energy dissipated by the primary electrons near the surface. Our analysis of energy spectra of secondary electrons indicates that the fraction of dissipated energy of primary electrons in solid reaches the maximum at the primary energies that produce the maximum yield. The better understanding of this mechanism is crucial for successful modeling of the multipactor discharge and design of vacuum electronic devices. We have developed an experimental set up to measure energy distribution of SEE from Nb coupons under different incident angles, since Nb is used for manufacturing of SRF accelerating cavities. Samples are placed in carousel target manifolds which are manipulated by robotic arm providing multiple degrees of freedom of a whole target system. Work supported by JSA/DOE contract No. DE-AC05-06OR23177.
Fantz, U.; Friedl, R.; Briefi, S.
2015-05-01
The visual properties of a large plasmoid rising from a water container into the air for up to 450 ms are brought into correlation with the total energy dissipated into the system, and, in particular, with the energy used for plasma generation. The latter parameters are deduced from the time-resolved discharge current and voltage of the capacitor bank which is used as energy supply. By varying the experimental parameters, the energy dissipated to the system varies between 5 kJ and 30 kJ from which 10% to 30% is transferred to the plasma. Clear correlations are obtained for the size of the plasmoid changing from 15 cm to 35 cm in width, the ascent velocity ranging from 1 m/s to 2 m/s, and the rising height for which up to 85 cm is measured. For the relation of the autonomous phase with the energy transferred to the plasma, two trends are observed: 450 ms duration is achieved in maximum with the present setup being almost independent on the electrode gap, the voltage-on time, the water conductivity, or the type of salt dissolved in the water. On the other hand, an almost linear dependence is obtained by changing the capacitance.
Energy dissipation on ion-accelerator grids during high-voltage breakdown
International Nuclear Information System (INIS)
Menon, M.M.; Ponte, N.S.
1981-01-01
The effects of stored energy in the system capacitance across the accelerator grids during high voltage vacuum breakdown are examined. Measurements were made of the current flow and the energy deposition on the grids during breakdown. It is shown that only a portion (less than or equal to 40 J) of the total stored energy (congruent to 100 J) is actually dissipated on the grids. Most of the energy is released during the formation phase of the vacuum arc and is deposited primarily on the most positive grid. Certain abnormal situations led to energy depositions of about 200 J on the grid, but the ion accelerator endured them without exhibiting any deterioration in performance
Frictional systems under periodic loads — History-dependence, non-uniqueness and energy dissipation
International Nuclear Information System (INIS)
Barber, J R
2012-01-01
Nominally static contacts such as bolted or shrink-fit joints typically experience regions of microslip when subjected to oscillatory loading. This results in energy dissipation, reflected as apparent hysteretic damping of the system, and also may cause the initiation of fretting fatigue cracks. Early theoretical studies of the Hertzian contact problem by Cattaneo and Mindlin were confirmed experimentally by Johnson, who identified signs of fretting damage in the slip annulus predicted by the theory. For many years, tribologists assumed that Melan's theorem in plasticity could be extended to frictional systems — i.e. that if there exists a state of residual stress associated with frictional slip that is sufficient to prevent periodic slip in the steady state, then the system will shake down, regardless of the initial condition. However, we now know that this is true only if there is no coupling between the normal and tangential loading problems, as will be the case notably when contact occurs on a symmetry plane. For all other cases, periodic loading scenarios can be devised such that shakedown occurs for some initial conditions and not for others. The initial condition here might be determined by the assembly protocol — e.g. the order in which a set of bolts is tightened — or by the exact loading path before the steady cycle is attained. This non-uniqueness of the steady state persists at load amplitudes above the shakedown limit, in which case there is always some dissipation, but the dissipation per cycle (and hence both the effective damping and the susceptibility to fretting damage) depends on the initial conditions. This implies that fretting fatigue experiments need to follow a well-defined assembly protocol if reproducible results are to be obtained. We shall also present results showing that when both normal and tangential forces vary in time, the energy dissipation is very sensitive to the relative phase of the oscillatory components, being greatest
Solar transformities for the tidal energy received by the earth and the tidal energy dissipated globally can be calculated because both solar energy and the gravitational attraction of the sun and moon drive independent processes that produce an annual flux of geopotential energy...
Directory of Open Access Journals (Sweden)
Heng Shao
2016-01-01
Full Text Available This study aimed to investigate energy dissipation in train collisions. A 1/8 scaled train model, about one-dimensional in longitudinal direction, was used to carry out a scaled train collision test. Corresponding multibody dynamic simulations were conducted using traditional and improved method model (IMM in ADAMS. In IMM, the connection between two adjacent cars was expressed by a nonlinear spring and energy absorbing structures were equivalently represented by separate forces, instead of one force. IMM was able to simulate the motion of each car and displayed the deformation of structures at both ends of the cars. IMM showed larger deformations and energy absorption of structures in moving cars than those in stationary cars. Moreover, the asymmetry in deformation proportion in main energy absorbing structures decreased with increasing collision speed. The asymmetry decreased from 11.69% to 3.60% when the collision speed increased from 10 km/h to 36 km/h.
Towards development of lignin reinforced elastomeric compounds with reduced energy dissipation
Bahl, Kushal
This research deals with development of lignin as reinforcing filler for elastomeric compounds. Lignins are naturally abundant and cost competitive wood derivatives possessing strong mechanical properties and offering reactive functional groups on their surfaces. The presence of the functional groups imparts polarity to the lignin molecules and makes them incompatible with non-polar elastomers. Also, the large particle size of lignin does not produce desired mechanical reinforcement. The present study deals with solving the outstanding issues associated with the use of lignin as fillers for polymeric compounds. In addition, the work specifically focuses on producing rubber compounds with reduced energy dissipation via partial replacement of carbon black with lignin. The first part of this study is devoted to suppression of the polarity of lignin and achievement of compatibility with rubber matrix via modification of lignosulfonates (LS) with cyclohexylamine (CA). CA reduces the polarity of lignin via interactions originating from proton transfer and hydrogen bonding. X-ray Photoelectron Spectroscopy (XPS) confirms the attachment of CA on the surfaces of lignin. The mechanical properties of rubber compounds increase substantially along with improvement in cure properties and increase in crosslink density in the presence of LS particles modified with CA. The tensile strength and storage modulus show an increase by 45% and 41% respectively. The values of the 100% modulus and elongation at break also improve by 35% and 60% respectively. The second part of this study exploits the non-covalent interactions between lignin and carbon black (CB) for the design of novel hybrid filler particles exhibiting lower energy loss in rubber compounds. The hybrid fillers offer unique morphology consisting of coating layers of lignin on carbon black particle aggregates. It is found that such coating layers are formed due to pi-pi interactions between lignin and carbon black. Raman
Effects of railway track design on the expected degradation: Parametric study on energy dissipation
Sadri, Mehran; Steenbergen, Michaël
2018-04-01
This paper studies the effect of railway track design parameters on the expected long-term degradation of track geometry. The study assumes a geometrically perfect and straight track along with spatial invariability, except for the presence of discrete sleepers. A frequency-domain two-layer model is used of a discretely supported rail coupled with a moving unsprung mass. The susceptibility of the track to degradation is objectively quantified by calculating the mechanical energy dissipated in the substructure under a moving train axle for variations of different track parameters. Results show that, apart from the operational train speed, the ballast/substructure stiffness is the most significant parameter influencing energy dissipation. Generally, the degradation increases with the train speed and with softer substructures. However, stiff subgrades appear more sensitive to particular train velocities, in a regime which is mostly relevant for conventional trains (100-200 km/h) and less for high-speed operation, where a stiff subgrade is always favorable and can reduce the sensitivity to degradation substantially, with roughly a factor up to 7. Also railpad stiffness, sleeper distance and rail cross-sectional properties are found to have considerable effect, with higher expected degradation rates for increasing railpad stiffness, increasing sleeper distance and decreasing rail profile bending stiffness. Unsprung vehicle mass and sleeper mass have no significant influence, however, only against the background of the assumption of an idealized (invariant and straight) track. Apart from dissipated mechanical energy, the suitability of the dynamic track stiffness is explored as an engineering parameter to assess the sensitivity to degradation. It is found that this quantity is inappropriate to assess the design of an idealized track.
Pushover analysis method for asymmetric structure with passive energy dissipation devices
Li, Gang; Li, Hong-nan
2009-03-01
This paper presents a simplified method to calculate pushover curves for an asymmetric structure with displacement-dependent passive energy dissipation devices (DDPEDDs). The deformations of a symmetric structure are analyzed in translation and torsion, respectively. These results are then combined in order to calculate the pushover curve for an asymmetric structure with DDPEDDs. The numerical results obtained by using the simplified analytical method are then compared to those obtained from the analysis of the models using the software SAP2000. The results show that the simplified analytical method can be an effective tool for engineering analysis of an asymmetric structure.
Energy dissipation within the wave run-up at stepped revetments
Kerpen, Nils B.; Bung, Daniel B.; Valero, Daniel; Schlurmann, Torsten
2017-08-01
To understand the processes and energy dissipation performance caused by turbulence during the wave run-up over a stepped revetment, hydraulic model tests with steady flow conditions are conducted and correlated with unsteady flow conditions of the wave run-up within a short time frame. Under irregular waves, the run-up reduction over a stepped revetment is dependent on the Iribarren number and decreases for decreasing Iribarren numbers. Velocity gradients are found to be similar in a steady and unsteady flow regime near the pseudo-bottom.
Periodicities in energy dissipation rates in the auroral mesosphere/lower thermosphere
Directory of Open Access Journals (Sweden)
C. M. Hall
2003-03-01
Full Text Available It is possible for medium-frequency (MF radar systems to estimate kinetic energy dissipation rates by measuring signal fading times. Here, we present approximately 5 years of such results from Tromsø (69° N, 19° E and in particular, investigate the periodicities present at different altitudes in the regime 80 to 100 km. We detect the known annual variation in the mesosphere and the semiannual variation on the lower thermosphere. In addition, other features are observed including terannual and ~ 27-day components in the lower thermosphere.Key words. Meteorology and atmospheric dynamics (climatology; middle atmosphere dynamics; turbulence
Geometrical Dependence of Electrical Energy dissipated for Intra-Cloud Flashes using LMA Data
Salinas, V.; Bruning, E. C.
2015-12-01
Lightning Mapping Array (LMA) data were used to estimate total electrical energy dissipation for 73 intra-cloud flashes from a Mesoscale Convective System (MCS) that occurred near Lubbock, TX on June 6th, 2013. Charge volumes and spacing were estimated from the convex hull of VHF sources emitted by positive and negative breakdown. Energy was obtained by solving for the electric field and potential in two ways. For reference, a three-dimensional Poisson solver was used with the observed convex hull geometry. Analytical estimates were then made by applying the same charge volumes to simplified geometries: charged spheres, cylinders, and plane parallel discs. Charge density was retrieved by applying constraints of charge conservation and the presence of a breakeven electric field. The analytic geometries were compared to the convex hull method in order to quantify and evaluate the geometric dependence of the total energy dissipated. Preliminary results showed the cylindrical geometry produced values within the range of other values reported in the literature, and in close agreement with solutions for the convex-hull geometry.
Zehe, Erwin; Blume, Theresa; Blöschl, Günter
2010-05-12
Preferential flow in biological soil structures is of key importance for infiltration and soil water flow at a range of scales. In the present study, we treat soil water flow as a dissipative process in an open non-equilibrium thermodynamic system, to better understand this key process. We define the chemical potential and Helmholtz free energy based on soil physical quantities, parametrize a physically based hydrological model based on field data and simulate the evolution of Helmholtz free energy in a cohesive soil with different populations of worm burrows for a range of rainfall scenarios. The simulations suggest that flow in connected worm burrows allows a more efficient redistribution of water within the soil, which implies a more efficient dissipation of free energy/higher production of entropy. There is additional evidence that the spatial pattern of worm burrow density at the hillslope scale is a major control of energy dissipation. The pattern typically found in the study is more efficient in dissipating energy/producing entropy than other patterns. This is because upslope run-off accumulates and infiltrates via the worm burrows into the dry soil in the lower part of the hillslope, which results in an overall more efficient dissipation of free energy.
Ge, Hao; Qian, Hong
2013-06-01
Nonequilibrium thermodynamics of a system situated in a sustained environment with influx and efflux is usually treated as a subsystem in a larger, closed "universe." A question remains with regard to what the minimally required description for the surrounding of such an open driven system is so that its nonequilibrium thermodynamics can be established solely based on the internal stochastic kinetics. We provide a solution to this problem using insights from studies of molecular motors in a chemical nonequilibrium steady state (NESS) with sustained external drive through a regenerating system or in a quasisteady state (QSS) with an excess amount of adenosine triphosphate (ATP), adenosine diphosphate (ADP), and inorganic phosphate (Pi). We introduce the key notion of minimal work that is needed, W(min), for the external regenerating system to sustain a NESS (e.g., maintaining constant concentrations of ATP, ADP and Pi for a molecular motor). Using a Markov (master-equation) description of a motor protein, we illustrate that the NESS and QSS have identical kinetics as well as the second law in terms of the same positive entropy production rate. The heat dissipation of a NESS without mechanical output is exactly the W(min). This provides a justification for introducing an ideal external regenerating system and yields a free-energy balance equation between the net free-energy input F(in) and total dissipation F(dis) in an NESS: F(in) consists of chemical input minus mechanical output; F(dis) consists of dissipative heat, i.e. the amount of useful energy becoming heat, which also equals the NESS entropy production. Furthermore, we show that for nonstationary systems, the F(dis) and F(in) correspond to the entropy production rate and housekeeping heat in stochastic thermodynamics and identify a relative entropy H as a generalized free energy. We reach a new formulation of Markovian nonequilibrium thermodynamics based on only the internal kinetic equation without further
Viscous dissipation of energy at the stage of accumulation of the Earth
Yurie Khachay, Professor; Olga Hachay, Professor; Antipin, Alexandr
2017-04-01
In the papers [1,2] it is published the differentiation model of the proto planet cloud during the accumulation of the Earth's group planets. In [2] it was shown that the energy released during the decay of short-lived radioactive elements in the small size more than 50 km, it is enough that the temperature inside of the protoplanet becomes larger than the temperature of iron melting. It provides a realization of the matter differentiation process and convection development inside the inner envelopes. With increasing of the Earth, the forming region of the outer core remains in a molten state, although the power and viscosity of the layer changed. In [3] it is shown that during the sequence of growth changes of accumulated protoplanets, the main contribution of heat is provided first by radioactive sources, and then heated from above by converting the kinetic energy during the growing impact inside the Earth, and finally heated from below. That provides three types of driving mechanisms of convection: internal heat sources; heated top; heated from bottom and chemical-thermal convection. At all stages of proto Earth's development the convective heat-mass transfer becomes a most significant factor in the dynamics of the planet. However, the heat release due to friction in the viscous liquid of the outer core up to now was not still considered, or it was considered only for the formed planetary envelopes with a constant radius. In this paper we present the first results of thermal evolution numerical modeling of 3D spherical segment for a protoplanet with increasing radius and accounting random falling of bodies and particles. To describe the planetary accumulation Safronov equation is used [4]. For the quantitative account of the released heat by viscous friction a system of hydro dynamic equations for a viscous liquid is used. The obtained results show that the heat input due to viscous friction heat release at the early stage of planetary accumulation was very
Energy input and dissipation in a temperate lake during the spring transition
Woolway, R. Iestyn; Simpson, John H.
2017-08-01
ADCP and temperature chain measurements have been used to estimate the rate of energy input by wind stress to the water surface in the south basin of Windermere. The energy input from the atmosphere was found to increase markedly as the lake stratified in spring. The efficiency of energy transfer ( Eff), defined as the ratio of the rate of working in near-surface waters ( RW) to that above the lake surface ( P 10), increased from ˜0.0013 in vertically homogenous conditions to ˜0.0064 in the first 40 days of the stratified regime. A maximum value of Eff˜0.01 was observed when, with increasing stratification, the first mode internal seiche period decreased to match the diurnal wind period of 24 h. The increase in energy input, following the onset of stratification was reflected in enhancement of the mean depth-varying kinetic energy without a corresponding increase in wind forcing. Parallel estimates of energy dissipation in the bottom boundary layer, based on determination of the structure function show that it accounts for ˜15% of RW in stratified conditions. The evolution of stratification in the lake conforms to a heating stirring model which indicates that mixing accounts for ˜21% of RW. Taken together, these estimates of key energetic parameters point the way to the development of full energy budgets for lakes and shallow seas.
Tkatchenko, Alexandre; Ambrosetti, Alberto; DiStasio, Robert A.
2013-02-01
Interatomic pairwise methods are currently among the most popular and accurate ways to include dispersion energy in density functional theory calculations. However, when applied to more than two atoms, these methods are still frequently perceived to be based on ad hoc assumptions, rather than a rigorous derivation from quantum mechanics. Starting from the adiabatic connection fluctuation-dissipation (ACFD) theorem, an exact expression for the electronic exchange-correlation energy, we demonstrate that the pairwise interatomic dispersion energy for an arbitrary collection of isotropic polarizable dipoles emerges from the second-order expansion of the ACFD formula upon invoking the random-phase approximation (RPA) or the full-potential approximation. Moreover, for a system of quantum harmonic oscillators coupled through a dipole-dipole potential, we prove the equivalence between the full interaction energy obtained from the Hamiltonian diagonalization and the ACFD-RPA correlation energy. This property makes the Hamiltonian diagonalization an efficient method for the calculation of the many-body dispersion energy. In addition, we show that the switching function used to damp the dispersion interaction at short distances arises from a short-range screened Coulomb potential, whose role is to account for the spatial spread of the individual atomic dipole moments. By using the ACFD formula, we gain a deeper understanding of the approximations made in the interatomic pairwise approaches, providing a powerful formalism for further development of accurate and efficient methods for the calculation of the dispersion energy.
Comparative study of passive and semi-active energy dissipation devices intended for overhead cranes
International Nuclear Information System (INIS)
Guihot, P.; Revaud, D.
1996-04-01
This paper deals with the results of a bibliographic survey of energy dissipation devices which could be adapted for overhead cranes. The principle of passive devices using friction, yielding steel systems of viscous and viscoelastic systems are remembered. An active control system, which needs a minimum of external control energy is also presented. The application to overhead cranes which have a strong non linear behaviour under strong seismic motion (sliding between rails and wheels, local yielding and damage) is further discussed. The first results of a numerical study in progress are likewise purposed. The criterion of selection of the devices turn on the performance, the robustness and the reliability. The behaviour in the presence of non linearities, the sensitivity to the variations of the vibratory characteristics, and lastly the sensitivity to the response delay of the active controller are taken into account. (authors). 14 refs., 4 figs
Xiong, Liping; Lan, Ganhui
2015-01-01
Sustained molecular oscillations are ubiquitous in biology. The obtained oscillatory patterns provide vital functions as timekeepers, pacemakers and spacemarkers. Models based on control theory have been introduced to explain how specific oscillatory behaviors stem from protein interaction feedbacks, whereas the energy dissipation through the oscillating processes and its role in the regulatory function remain unexplored. Here we developed a general framework to assess an oscillator’s regulation performance at different dissipation levels. Using the Escherichia coli MinCDE oscillator as a model system, we showed that a sufficient amount of energy dissipation is needed to switch on the oscillation, which is tightly coupled to the system’s regulatory performance. Once the dissipation level is beyond this threshold, unlike stationary regulators’ monotonic performance-to-cost relation, excess dissipation at certain steps in the oscillating process damages the oscillator’s regulatory performance. We further discovered that the chemical free energy from ATP hydrolysis has to be strategically assigned to the MinE-aided MinD release and the MinD immobilization steps for optimal performance, and a higher energy budget improves the robustness of the oscillator. These results unfold a novel mode by which living systems trade energy for regulatory function. PMID:26317492
Laser energy-pooling processes in an optically thick Cs vapor near a dissipative surface
International Nuclear Information System (INIS)
Gagne, Jean-Marie; Le Bris, Karine; Gagne, Marie-Claude
2002-01-01
We characterize, for the first time to our knowledge, the laser-induced backward fluorescence (retrofluorescence) spectra that result from energy-pooling collisions between Cs atoms near a dissipative thin Cs layer on a glass substrate. We resolve, experimentally and theoretically, the laser spectroscopic problem of energy-pooling processes related to the nature of the glass-metallic vapor interface. Our study focused on the integrated laser-induced retrofluorescence spectra for the 455.5-nm (7 2 P 3/2 -6 2 S 1/2 ) and 852.2-nm (6 2 P 3/2 -6 2 S 1/2 ) lines as a function of laser scanning through pumping resonance at the 852.2-nm line. We experimentally investigate the retrofluorescence from 420 to 930 nm, induced by a diode laser tuned either in the wings or in the center of the pumping resonance line. We present a detailed theoretical model of the retrofluorescence signal based on the radiative transfer equation, taking into account the evanescent wave of the excited atomic dipole strongly coupled with a dissipative surface. Based on theoretical and experimental results, we evaluate the effective nonradiative transfer rate A(bar sign) 6 2 P 3/2 →6 2 S 1/2s f for atoms in the excited 6 2 P 3/2 level located in the near-field region of the surface of the cell. Values extracted from the energy-pooling process analysis are equivalent to those found directly from the 852.2-nm resonance retrofluorescence line. We show that the effective energy-pooling coefficients k-tilde 7 2 P 3/2 and k-tilde 7 2 P 1/2 are approximately equal. The agreement between theory and experiment is remarkably good, considering the simplicity of the model
Energy dissipation/transfer and stable attitude of spatial on-orbit tethered system
Hu, Weipeng; Song, Mingzhe; Deng, Zichen
2018-01-01
For the Tethered Satellite System, the coupling between the platform system and the solar panel is a challenge in the dynamic analysis. In this paper, the coupling dynamic behaviors of the Tethered Satellite System that is idealized as a planar flexible damping beam-spring-mass composite system are investigated via a structure-preserving method. Considering the coupling between the plane motion of the system, the oscillation of the spring and the transverse vibration of the beam, the dynamic model of the composite system is established based on the Hamiltonian variational principle. A symplectic dimensionality reduction method is proposed to decouple the dynamic system into two subsystems approximately. Employing the complex structure-preserving approach presented in our previous work, numerical iterations are performed between the two subsystems with weak damping to study the energy dissipation/transfer in the composite system, the effect of the spring stiffness on the energy distribution and the effect of the particle mass on the stability of the composite system. The numerical results show that: the energy transfer approach is uniquely determined by the initial attitude angle, while the energy dissipation speed is mainly depending on the initial attitude angle and the spring stiffness besides the weak damping. In addition, the mass ratio between the platform system and the solar panel determines the stable state as well as the time needed to reach the stable state of the composite system. The numerical approach presented in this paper provides a new way to deal with the coupling dynamic system and the conclusions obtained give some useful advices on the overall design of the Tethered Satellite System.
Do inertial wave interactions control the rate of energy dissipation of rotating turbulence?
Cortet, Pierre-Philippe; Campagne, Antoine; Machicoane, Nathanael; Gallet, Basile; Moisy, Frederic
2015-11-01
The scaling law of the energy dissipation rate, ɛ ~U3 / L (with U and L the characteristic velocity and lengthscale), is one of the most robust features of fully developed turbulence. How this scaling is affected by a background rotation is still a controversial issue with importance for geo and astrophysical flows. At asymptotically small Rossby numbers Ro = U / ΩL , i.e. in the weakly nonlinear limit, wave-turbulence arguments suggest that ɛ should be reduced by a factor Ro . Such scaling has however never been evidenced directly, neither experimentally nor numerically. We report here direct measurements of the injected power, and therefore of ɛ, in an experiment where a propeller is rotating at a constant rate in a large volume of fluid rotating at Ω. In co-rotation, we find a transition between the wave-turbulence scaling at small Ro and the classical Kolmogorov law at large Ro . The transition between these two regimes is characterized from experiments varying the propeller and tank dimensions. In counter-rotation, the scenario is much richer with the observation of an additional peak of dissipation, similar to the one found in Taylor-Couette experiments.
Seiffert, Betsy R.; Ducrozet, Guillaume
2018-01-01
We examine the implementation of a wave-breaking mechanism into a nonlinear potential flow solver. The success of the mechanism will be studied by implementing it into the numerical model HOS-NWT, which is a computationally efficient, open source code that solves for the free surface in a numerical wave tank using the high-order spectral (HOS) method. Once the breaking mechanism is validated, it can be implemented into other nonlinear potential flow models. To solve for wave-breaking, first a wave-breaking onset parameter is identified, and then a method for computing wave-breaking associated energy loss is determined. Wave-breaking onset is calculated using a breaking criteria introduced by Barthelemy et al. (J Fluid Mech https://arxiv.org/pdf/1508.06002.pdf, submitted) and validated with the experiments of Saket et al. (J Fluid Mech 811:642-658, 2017). Wave-breaking energy dissipation is calculated by adding a viscous diffusion term computed using an eddy viscosity parameter introduced by Tian et al. (Phys Fluids 20(6): 066,604, 2008, Phys Fluids 24(3), 2012), which is estimated based on the pre-breaking wave geometry. A set of two-dimensional experiments is conducted to validate the implemented wave breaking mechanism at a large scale. Breaking waves are generated by using traditional methods of evolution of focused waves and modulational instability, as well as irregular breaking waves with a range of primary frequencies, providing a wide range of breaking conditions to validate the solver. Furthermore, adjustments are made to the method of application and coefficient of the viscous diffusion term with negligible difference, supporting the robustness of the eddy viscosity parameter. The model is able to accurately predict surface elevation and corresponding frequency/amplitude spectrum, as well as energy dissipation when compared with the experimental measurements. This suggests the model is capable of calculating wave-breaking onset and energy dissipation
Turbulent energy dissipation rate in a tilting flume with a highly rough bed
Coscarella, F.; Servidio, S.; Ferraro, D.; Carbone, V.; Gaudio, R.
2017-08-01
Turbulent flows on highly rough beds, such as those occurring in natural watercourses, represent a longstanding and fascinating problem of hydraulics, motivating in the past few decades huge research on new models of turbulence. In this work, laboratory experiments are presented on a stream flowing on a heterogeneous pebble bed with varying slope. The analysis of the flow speed puts in evidence a clear inertial range, where the Kolmogorov 4/5-law for the streamwise velocity spatial increments holds. The law is used for a systematic estimation of the turbulent kinetic energy dissipation rate 𝜖 , here measured for three different bed slopes and hence for three different shear Reynolds numbers. The experiments presented here suggest that small scale turbulence has properties similar to the classical picture of homogeneous universal turbulence invoked by the Kolmogorov theory.
DEFF Research Database (Denmark)
Liu, Chao; Thormann, Esben; Tyrode, Eric
2015-01-01
, but not the friction coefficient. This suggests that the main energy dissipation mechanism arises from processes occurring within the hydrogel layer, rather than at the silica/hydrogel interface, and we suggest that it is related to stretching of polymer chains between the cross-linking points. We also find...... that an increased cross-linking density, from 40% to 100%, in the hydrogel reduces the friction coefficient....... the concentration of counterions within the hydrogel to keep the interior close to uncharged, which is similar to what has been observed for polyelectrolyte brushes. Changes in pH and ionic strength affect the adhesion force and the friction force between the silica surface and the hydrogel layer...
Non-linear dynamics in biological microtubules: solitons and dissipation-free energy transfer
Mavromatos, Nick E.
2017-08-01
I review some recent developments concerning soliton solutions in biological microtubules and their significance in transferring energy without dissipation. I discuss various types of soliton solutions, as well as ‘spikes’, of the associated non-linear Lagrange equations describing the dynamics of a ‘pseudo-spin non-linear σ-model’ that models the dynamics of a microtubule system with dipole-dipole interactions. These results will hopefully contribute to a better understanding of the functional properties of microtubules, including the motor protein dynamics and the information transfer processes. With regards to the latter we also speculate on the use of microtubules as ‘logical’ gates. Our considerations are classical, but the soliton solutions may have a microscopic quantum origin, which we briefly touch upon.
Directory of Open Access Journals (Sweden)
Andrew S. Blasetti
2012-06-01
Full Text Available A key element in the seismic load resisting system of a wood framed structure is the shear wall which is typically sheathed on one side with plywood or oriented strand board (OSB and gypsum on the other. The shear capacity of gypsum sheathed shear walls is typically neglected in high seismic areas due to the susceptibility of conventional drywall screw connections to damage caused by earthquakes. The earthquake resistance of an innovative viscoelastic (VE gypsum shearwall is evaluated and compared to conventional structural and non-structural walls. Ten 8 ft × 8 ft wood framed wall specimens of three configurations [nailed-OSB, screw-gypsum, and VE polymer-gypsum] were subjected to a cyclic test protocol. The energy dissipation, stiffness, and damage characteristics of all shearwalls are reported herein. Testing results indicate the VE-gypsum walls can dissipate more energy than the OSB structural panels and 500% more energy that the conventional gypsum sheathed walls and contains a constant source of energy dissipation not seen in the structural and non-structural walls. The wall stiffness of the OSB wall degrades at a far greater rate that the VE gypsum wall and at continued cycling degrades below the VE wall stiffness. Unlike both of the conventional wall types, the VE wall showed no visible or audible signs of damage when subjected to shear displacements up to 1.
Arai, Toyoko; Inamura, Ryo; Kura, Daiki; Tomitori, Masahiko
2018-03-01
The kinetic energy of the oscillating cantilever of noncontact atomic force microscopy (nc-AFM) at room temperature was considerably dissipated over regions between a Si adatom and its neighboring rest atom for Si(111 )-(7 ×7 ) in close proximity to a Si tip on the cantilever. However, nc-AFM topographic images showed no atomic features over those regions, which were the hollow sites of the (7 ×7 ). This energy dissipation likely originated from displacement of Si adatoms with respect to the tip over the hollow sites, leading to a lateral shift of the adatoms toward the rest atom. This interaction led to hysteresis over each cantilever oscillation cycle; when the tip was retracted, the Si adatom likely returned to its original position. To confirm the atomic processes involved in the force interactions through Si dangling bonds, the Si(111 )-(7 ×7 ) surface was partly terminated with atomic hydrogen (H) and examined by nc-AFM. When the Si adatoms and/or the rest atoms were terminated with H, the hollow sites were not bright (less dissipation) in images of the energy dissipation channels by nc-AFM. The hollow sites acted as metastable sites for Si adatoms in surface diffusion and atom manipulation; thus, the dissipation energy which is saturated on the tip likely corresponds to the difference in the potential energy between the hollow site and the Si adatom site. In this study, we demonstrated the ability of dissipation channels of nc-AFM to enable visualization of the dynamics of atoms and molecules on surfaces, which cannot be revealed by nc-AFM topographic images alone.
Energy dissipation in the blade tip region of an axial fan
Bizjan, B.; Milavec, M.; Širok, B.; Trenc, F.; Hočevar, M.
2016-11-01
A study of velocity and pressure fluctuations in the tip clearance flow of an axial fan is presented in this paper. Two different rotor blade tip designs were investigated: the standard one with straight blade tips and the modified one with swept-back tip winglets. Comparison of integral sound parameters indicates a significant noise level reduction for the modified blade tip design. To study the underlying mechanisms of the energy conversion and noise generation, a novel experimental method based on simultaneous measurements of local flow velocity and pressure has also been developed and is presented here. The method is based on the phase space analysis by the use of attractors, which enable more accurate identification and determination of the local flow structures and turbulent flow properties. Specific gap flow energy derived from the pressure and velocity time series was introduced as an additional attractor parameter to assess the flow energy distribution and dissipation within the phase space, and thus determines characteristic sources of the fan acoustic emission. The attractors reveal a more efficient conversion of the pressure to kinetic flow energy in the case of the modified (tip winglet) fan blade design, and also a reduction in emitted noise levels. The findings of the attractor analysis are in a good agreement with integral fan characteristics (efficiency and noise level), while offering a much more accurate and detailed representation of gap flow phenomena.
Reassessing the Plastic Hinge Model for Energy Dissipation of Axially Loaded Columns
Directory of Open Access Journals (Sweden)
R. M. Korol
2014-01-01
Full Text Available This paper investigates the energy dissipation potential of axially loaded columns and evaluates the use of a plastic hinge model for analysis of hi-rise building column collapse under extreme loading conditions. The experimental program considered seven axially loaded H-shaped extruded aluminum structural section columns having slenderness ratios that would be typical of floor-to-ceiling heights in buildings. All seven test specimens initially experienced minor-axis overall buckling followed by formation of a plastic hinge at the mid-height region, leading to local buckling of the flanges on the compression side of the plastic hinge, and eventual folding of the compression flanges. The experimental energy absorption, based on load-displacement relations, was compared to the energy estimates based on section plastic moment resistance based on measured yield stress and based on measured hinge rotations. It was found that the theoretical plastic hinge model underestimates a column’s actual ability to absorb energy by a factor in the range of 3 to 4 below that obtained from tests. It was also noted that the realizable hinge rotation is less than 180°. The above observations are based, of course, on actual columns being able to sustain high tensile strains at hinge locations without fracturing.
Daane, Abigail R.; McKagan, Sarah B.; Vokos, Stamatis; Scherr, Rachel E.
2015-01-01
Research has demonstrated that many students and some teachers do not consistently apply the conservation of energy principle when analyzing mechanical scenarios. In observing elementary and secondary teachers engaged in learning activities that require tracking and conserving energy, we find that challenges to energy conservation often arise in…
Kokorian, Jaap; Merlijn van Spengen, W.
2017-11-01
In this paper we demonstrate a new method for analyzing and visualizing friction force measurements of meso-scale stick-slip motion, and introduce a method for extracting two separate dissipative energy components. Using a microelectromechanical system tribometer, we execute 2 million reciprocating sliding cycles, during which we measure the static friction force with a resolution of \
Garate, Hernan; Bianchi, Micaela; Pietrasanta, Lía I; Goyanes, Silvia; D'Accorso, Norma B
2017-01-11
Hierarchical assembly of hard/soft nanoparticles holds great potential as reinforcements for polymer nanocomposites with tailored properties. Here, we present a facile strategy to integrate polystyrene-grafted carbon nanotubes (PSgCNT) (0.05-0.3 wt %) and poly(styrene-b-[isoprene-ran-epoxyisoprene]-b-styrene) block copolymer (10 wt %) into epoxy coatings using an ultrasound-assisted noncovalent functionalization process. The method leads to cured nanocomposites with core-shell block copolymer (BCP) nanodomains which are associated with carbon nanotubes (CNT) giving rise to CNT-BCP hybrid structures. Nanocomposite energy dissipation and reduced Young's Modulus (E*) is determined from force-distance curves by atomic force microscopy operating in the PeakForce QNM imaging mode and compared to thermosets modified with BCP and purified carbon nanotubes (pCNT). Remarkably, nanocomposites bearing PSgCNT-BCP conjugates display an increase in energy dissipation of up to 7.1-fold with respect to neat epoxy and 53% more than materials prepared with pCNT and BCP at the same CNT load (0.3 wt %), while reduced Young's Modulus shows no significant change with CNT type and increases up to 25% compared to neat epoxy E* at a CNT load of 0.3 wt %. The energy dissipation performance of nanocomposites is also reflected by the lower wear coefficients of materials with PSgCNT and BCP compared to those with pCNT and BCP, as determined by abrasion tests. Furthermore, scanning electron microscopy (SEM) images taken on wear surfaces show that materials incorporating PSgCNT and BCP exhibit much more surface deformation under shear forces in agreement with their higher ability to dissipate more energy before particle release. We propose that the synergistic effect observed in energy dissipation arises from hierarchical assembly of PSgCNT and BCP within the epoxy matrix and provides clues that the CNT-BCP interface has a significant role in the mechanisms of energy dissipation of epoxy coating
Energy Technology Data Exchange (ETDEWEB)
Simmendinger, Julian; Pracht, Uwe S.; Daschke, Lena; Proslier, Thomas; Klug, Jeffrey A.; Dressel, Martin; Scheffler, Marc
2016-08-01
We report investigations of molybdenum nitride (MoN) thin films with different thickness and disorder and with superconducting transition temperature 9.89K >= T-c >= 2.78 K. Using terahertz frequency-domain spectroscopy we explore the normal and superconducting charge carrier dynamics for frequencies covering the range from 3 to 38 cm(-1) (0.1 to 1.1 THz). The superconducting energy scales, i.e., the critical temperature T-c, the pairing energy Delta, and the superfluid stiffness J, and the superfluid density n(s) can be well described within the Bardeen-Cooper-Schrieffer theory for conventional superconductors. At the same time, we find an anomalously large dissipative conductivity, which cannot be explained by thermally excited quasiparticles, but rather by a temperature-dependent normal-conducting fraction, persisting deep into the superconducting state. Our results on this disordered system constrain the regime, where discernible effects stemming from the disorder-induced superconductor-insulator transition possibly become relevant, to MoN films with a transition temperature lower than at least 2.78 K.
Parashar, T.; Yang, Y.; Chasapis, A.; Matthaeus, W. H.
2017-12-01
High resolution Magnetospheric Multiscale (MMS) plasma and magnetic field data obtained in the inhomogeneous turbulent magnetosheath directly reveals the exchanges of energy between electromagnetic, flow and random kinetic energy. The parameters that quantify these exchanges are based on standard manipulations of the collisionless Vlasov model of plasma dynamics [1], without appeal to viscous or other closures. No analysis of heat transport or heat conduction is carried out. Several intervals of burst mode data in the magnetosheath are considered. Time series of the work done by the electromagnetic field, and the pressure-stress interaction enable description of the pathways to dissipation in this low collisionality plasma. Using these examples we demonstrate that the pressure-stress interaction provides important information not readily revealed in other diagnostics concerning the physical processes that are observed. This method does not require any specific mechanism for its application such as reconnection or a selected mode, although with increased experience it will be useful in distinguishing among proposed possibilities. [1] Y. Yang et al, Phys. Plasmas 24, 072306 (2017); doi: 10.1063/1.4990421.
Energy Technology Data Exchange (ETDEWEB)
Zenkour, Ashraf M., E-mail: zenkour@hotmail.com [Department of Mathematics, Faculty of Science, King Abdulaziz University, Jeddah 21589 (Saudi Arabia); Department of Mathematics, Faculty of Science, Kafrelsheikh University, Kafr El-Sheikh 33516 (Egypt); Abbas, Ibrahim A. [Department of Mathematics, Faculty of Science and Arts-Khulais, King Abdulaziz University, Jeddah (Saudi Arabia); Department of Mathematics, Faculty of Science, Sohag University, Sohag (Egypt)
2015-12-01
The electro-magneto-thermo-elastic analysis problem of an infinite functionally graded (FG) hollow cylinder is studied in the context of Green–Naghdi's (G–N) generalized thermoelasticity theory (without energy dissipation). Material properties are assumed to be graded in the radial direction according to a novel power-law distribution in terms of the volume fractions of the metal and ceramic constituents. The inner surface of the FG cylinder is pure metal whereas the outer surface is pure ceramic. The equations of motion and the heat-conduction equation are used to derive the governing second-order differential equations. A finite element scheme is presented for the numerical purpose. The system of differential equations is solved numerically and some plots for displacement, radial and electromagnetic stresses, and temperature are presented. The radial displacement, mechanical stresses and temperature as well as the electromagnetic stress are all investigated along the radial direction of the infinite cylinder. - Highlights: • The electro-magneto-thermo-elastic analysis problem of a FG cylinder is studied. • A finite element scheme is presented for the numerical purpose. • The results are investigated along the radial direction of the infinite cylinder. • It provides interesting information for all researchers working on this subject.
International Nuclear Information System (INIS)
Zenkour, Ashraf M.; Abbas, Ibrahim A.
2015-01-01
The electro-magneto-thermo-elastic analysis problem of an infinite functionally graded (FG) hollow cylinder is studied in the context of Green–Naghdi's (G–N) generalized thermoelasticity theory (without energy dissipation). Material properties are assumed to be graded in the radial direction according to a novel power-law distribution in terms of the volume fractions of the metal and ceramic constituents. The inner surface of the FG cylinder is pure metal whereas the outer surface is pure ceramic. The equations of motion and the heat-conduction equation are used to derive the governing second-order differential equations. A finite element scheme is presented for the numerical purpose. The system of differential equations is solved numerically and some plots for displacement, radial and electromagnetic stresses, and temperature are presented. The radial displacement, mechanical stresses and temperature as well as the electromagnetic stress are all investigated along the radial direction of the infinite cylinder. - Highlights: • The electro-magneto-thermo-elastic analysis problem of a FG cylinder is studied. • A finite element scheme is presented for the numerical purpose. • The results are investigated along the radial direction of the infinite cylinder. • It provides interesting information for all researchers working on this subject
Troncoso, Omar P.; Gigos, Florian; Torres, Fernando G.
2017-11-01
Arapaima gigas scales are natural laminated composite materials made of individual layers with different degrees of mineralization, accompanied of varying mechanical properties. This natural design provides scales with hardness and flexibility, and can serve as a source of inspiration for the development of new layered composites with a hard surface and flexible base. In this paper, we have carried out cyclic micro-indentation tests on both; the internal and the highly mineralized external surface of air dried and wet scales, in order to assess the variation of their local micromechanical properties with regard to the mineral and water content. The load-penetration (P-h) curves showed that creep takes place throughout the application of a constant force during the micro-indentation tests, confirming the time dependent response of A. gigas scales. A model that accounted for the elastic, plastic and viscous responses of the samples was used to fit the experimental results. The penetration depth during loading and creep, as well as the energy dissipated are dependent on the water content. The used model suggests that the viscous response of the internal layer increases with the water content.
Directory of Open Access Journals (Sweden)
Cheng-Wei Ma
Full Text Available A novel approach to reveal intramolecular signal transduction network is proposed in this work. To this end, a new algorithm of network construction is developed, which is based on a new protein dynamics model of energy dissipation. A key feature of this approach is that direction information is specified after inferring protein residue-residue interaction network involved in the process of signal transduction. This enables fundamental analysis of the regulation hierarchy and identification of regulation hubs of the signaling network. A well-studied allosteric enzyme, E. coli aspartokinase III, is used as a model system to demonstrate the new method. Comparison with experimental results shows that the new approach is able to predict all the sites that have been experimentally proved to desensitize allosteric regulation of the enzyme. In addition, the signal transduction network shows a clear preference for specific structural regions, secondary structural types and residue conservation. Occurrence of super-hubs in the network indicates that allosteric regulation tends to gather residues with high connection ability to collectively facilitate the signaling process. Furthermore, a new parameter of propagation coefficient is defined to determine the propagation capability of residues within a signal transduction network. In conclusion, the new approach is useful for fundamental understanding of the process of intramolecular signal transduction and thus has significant impact on rational design of novel allosteric proteins.
Directory of Open Access Journals (Sweden)
Romit Maulik
2017-04-01
Full Text Available Solving two-dimensional compressible turbulence problems up to a resolution of 16, 384^2, this paper investigates the characteristics of two promising computational approaches: (i an implicit or numerical large eddy simulation (ILES framework using an upwind-biased fifth-order weighted essentially non-oscillatory (WENO reconstruction algorithm equipped with several Riemann solvers, and (ii a central sixth-order reconstruction framework combined with various linear and nonlinear explicit low-pass spatial filtering processes. Our primary aim is to quantify the dissipative behavior, resolution characteristics, shock capturing ability and computational expenditure for each approach utilizing a systematic analysis with respect to its modeling parameters or parameterizations. The relative advantages and disadvantages of both approaches are addressed for solving a stratified Kelvin-Helmholtz instability shear layer problem as well as a canonical Riemann problem with the interaction of four shocks. The comparisons are both qualitative and quantitative, using visualizations of the spatial structure of the flow and energy spectra, respectively. We observe that the central scheme, with relaxation filtering, offers a competitive approach to ILES and is much more computationally efficient than WENO-based schemes.
Lee, Harry; Wen, Baole; Doering, Charles
2017-11-01
The rate of viscous energy dissipation ɛ in incompressible Newtonian planar Couette flow (a horizontal shear layer) imposed with uniform boundary injection and suction is studied numerically. Specifically, fluid is steadily injected through the top plate with a constant rate at a constant angle of injection, and the same amount of fluid is sucked out vertically through the bottom plate at the same rate. This set-up leads to two control parameters, namely the angle of injection, θ, and the Reynolds number of the horizontal shear flow, Re . We numerically implement the `background field' variational problem formulated by Constantin and Doering with a one-dimensional unidirectional background field ϕ(z) , where z aligns with the distance between the plates. Computation is carried out at various levels of Re with θ = 0 , 0 .1° ,1° and 2°, respectively. The computed upper bounds on ɛ scale like Re0 as Re > 20 , 000 for each fixed θ, this agrees with Kolmogorov's hypothesis on isotropic turbulence. The outcome provides new upper bounds to ɛ among any solution to the underlying Navier-Stokes equations, and they are sharper than the analytical bounds presented in Doering et al. (2000). This research was partially supported by the NSF Award DMS-1515161, and the University of Michigan's Rackham Graduate Student Research Grant.
Energy decay for wave equations of phi-Laplacian type with weakly nonlinear dissipation
Directory of Open Access Journals (Sweden)
Aissa Guesmia
2008-08-01
Full Text Available In this paper, first we prove the existence of global solutions in Sobolev spaces for the initial boundary value problem of the wave equation of $phi$-Laplacian with a general dissipation of the form $$ (|u'|^{l-2}u''-Delta_{phi}u+sigma(t g(u'=0 quadext{in } Omegaimes mathbb{R}_+ , $$ where $Delta_{phi}=sum_{i=1}^n partial_{x_i}igl(phi (|partial_{x_i}|^2partial_{x_i}igr$. Then we prove general stability estimates using multiplier method and general weighted integral inequalities proved by the second author in [18]. Without imposing any growth condition at the origin on $g$ and $phi$, we show that the energy of the system is bounded above by a quantity, depending on $phi$, $sigma$ and $g$, which tends to zero (as time approaches infinity. These estimates allows us to consider large class of functions $g$ and $phi$ with general growth at the origin. We give some examples to illustrate how to derive from our general estimates the polynomial, exponential or logarithmic decay. The results of this paper improve and generalize many existing results in the literature, and generate some interesting open problems.
Energy Technology Data Exchange (ETDEWEB)
Kost, D.
2006-07-01
Motivated by the incomplete scientific description of the relaxation of highly charged ions in front of solid surfaces and their energy balance, this thesis describes an advanced complementary study of determining deposited fractions and re-emitted fractions of the potential energy of highly charged ions. On one side, a calorimetric measurement setup is used to determine the retained potential energy and on the other side, energy resolved electron spectroscopy is used for measuring the reemitted energy due to secondary electron emission. In order to study the mechanism of energy retention in detail, materials with different electronic structures are investigated: Cu, n-Si, p-Si and SiO{sub 2}. In the case of calorimetry, a linear relationship between the deposited potential energy and the inner potential energy of the ions was determined. The total potential energy which stays in the solid remains almost constant at about (80 {+-} 10) %. Comparing the results of the Cu, n-Si and p-Si targets, no significant difference could be shown. Therefore we conclude that the difference in energy deposition between copper, n-doped Si and p-doped Si is below 10 %, which is significantly lower than using SiO{sub 2} targets. For this purpose, electron spectroscopy provides a complementary result. For Cu and Si surfaces, an almost linear increase of the re-emitted energy with increasing potential energy of the ion up to Ar{sup 7+} was also observed. The ratio of the re-emitted energy is about (10 {+-} 5) % of the total potential energy of the incoming ion, almost independent of the ion charge state. In contrast, an almost vanishing electron emission was observed for SiO{sub 2} and for charge states below q=7. For Ar{sup 8+} and Ar{sup 9+}, the electron emission increased due to the contribution of the projectile LMM Auger electrons and the re-emitted energy amounts up to 20 % for Cu and Si and around 10 % for SiO{sub 2}. These results are in good agreement with the calorimetric
Twisting a β-Carotene, an Adaptive Trick from Nature for Dissipating Energy during Photoprotection.
Llansola-Portoles, Manuel J; Sobotka, Roman; Kish, Elizabeth; Shukla, Mahendra Kumar; Pascal, Andrew A; Polívka, Tomáš; Robert, Bruno
2017-01-27
Cyanobacteria possess a family of one-helix high light-inducible proteins (Hlips) that are homologous to light-harvesting antenna of plants and algae. An Hlip protein, high light-inducible protein D (HliD) purified as a small complex with the Ycf39 protein is evaluated using resonance Raman spectroscopy. We show that the HliD binds two different β-carotenes, each present in two non-equivalent binding pockets with different conformations, having their (0,0) absorption maxima at 489 and 522 nm, respectively. Both populations of β-carotene molecules were in all-trans configuration and the absorption position of the farthest blue-shifted β-carotene was attributed entirely to the polarizability of the environment in its binding pocket. In contrast, the absorption maximum of the red-shifted β-carotene was attributed to two different factors: the polarizability of the environment in its binding pocket and, more importantly, to the conformation of its β-rings. This second β-carotene has highly twisted β-rings adopting a flat conformation, which implies that the effective conjugation length N is extended up to 10.5 modifying the energetic levels. This increase in N will also result in a lower S 1 energy state, which may provide a permanent energy dissipation channel. Analysis of the carbonyl stretching region for chlorophyll a excitations indicates that the HliD binds six chlorophyll a molecules in five non-equivalent binding sites, with at least one chlorophyll a presenting a slight distortion to its macrocycle. The binding modes and conformations of HliD-bound pigments are discussed with respect to the known structures of LHCII and CP29. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.
International Nuclear Information System (INIS)
Guerreau, D.; Doubre, H.; Galin, J.; Pouthas, J.; Jahnke, U.; Jiang, D.X.; Lott, B.; Jacquet, D.
1988-01-01
A 4 π detector measuring the neutron multiplicities has been used to investigate the energy dissipation during peripheral collisions in Ar induced reactions around the Fermi Energy. Besides the persistance of direct transfer reactions for the most peripheral collisions, there are strong evidences for the occurrence of quite large energy dissipation, a clear signature for the one body friction to still play a major role at these intermediate energies
Pinnola, Alberta; Cazzaniga, Stefano; Alboresi, Alessandro; Nevo, Reinat; Levin-Zaidman, Smadar; Reich, Ziv; Bassi, Roberto
2015-11-01
Two LHC-like proteins, Photosystem II Subunit S (PSBS) and Light-Harvesting Complex Stress-Related (LHCSR), are essential for triggering excess energy dissipation in chloroplasts of vascular plants and green algae, respectively. The mechanism of quenching was studied in Physcomitrella patens, an early divergent streptophyta (including green algae and land plants) in which both proteins are active. PSBS was localized in grana together with photosystem II (PSII), but LHCSR was located mainly in stroma-exposed membranes together with photosystem I (PSI), and its distribution did not change upon high-light treatment. The quenched conformation can be preserved by rapidly freezing the high-light-treated tissues in liquid nitrogen. When using green fluorescent protein as an internal standard, 77K fluorescence emission spectra on isolated chloroplasts allowed for independent assessment of PSI and PSII fluorescence yield. Results showed that both photosystems underwent quenching upon high-light treatment in the wild type in contrast to mutants depleted of LHCSR, which lacked PSI quenching. Due to the contribution of LHCII, P. patens had a PSI antenna size twice as large with respect to higher plants. Thus, LHCII, which is highly abundant in stroma membranes, appears to be the target of quenching by LHCSR. © 2015 American Society of Plant Biologists. All rights reserved.
Bian, Yushu; Gao, Zhihui
2013-01-01
Due to the presence of system flexibility, impact can excite severe large amplitude vibration responses of the flexible robotic manipulator. This impact vibration exhibits characteristics of remarkable nonlinearity and strong energy. The main goal of this study is to put forward an energy-based control method to absorb and attenuate large amplitude impact vibration of the flexible robotic manipulator. The method takes advantage of internal resonance and is implemented through a vibration abso...
Hackerott, João A.; Bakhoday Paskyabi, Mostafa; Reuder, Joachim; de Oliveira, Amauri P.; Kral, Stephan T.; Marques Filho, Edson P.; Mesquita, Michel dos Santos; de Camargo, Ricardo
2017-11-01
We discuss scalar similarities and dissimilarities based on analysis of the dissipation terms in the variance budget equations, considering the turbulent kinetic energy and the variances of temperature, specific humidity and specific CO_2 content. For this purpose, 124 high-frequency sampled segments are selected from the Boundary Layer Late Afternoon and Sunset Turbulence experiment. The consequences of dissipation similarity in the variance transport are also discussed and quantified. The results show that, for the convective atmospheric surface layer, the non-dimensional dissipation terms can be expressed in the framework of Monin-Obukhov similarity theory and are independent of whether the variable is temperature or moisture. The scalar similarity in the dissipation term implies that the characteristic scales of the atmospheric surface layer can be estimated from the respective rate of variance dissipation, the characteristic scale of temperature, and the dissipation rate of temperature variance.
Noise and dissipation in magnetoelectronic nanostructures
Foros, Jørn
2008-01-01
This thesis adresses electric and magnetic noise and dissipation in magnetoelectronic nanostructures. Charge and spin current fluctuations are studied in various nanosized metallic structures consisting of both ferromagnetic and non-magnetic elements. The interplay between current and magnetization fluctuations, and the relation of these fluctuations to the electric and magnetic dissipation of energy, are considered. Special focus is on the enhancement of magnetization damping due to so-calle...
International Nuclear Information System (INIS)
Gung, C.Y.
1993-01-01
Energy dissipation, which is also called AC loss, of a composite multifilamentary superconducting wire is one of the most fundamental concerns in building a stable superconducting magnet. Characterization and reduction of AC losses are especially important in designing a superconducting magnet for generating transient magnetic fields. The goal of this thesis is to improve the understanding of AC-loss properties of superconducting wires developed for high-current ramp-field magnet applications. The major tasks include: (1) building an advanced AC-loss measurement system, (2) measuring AC losses of superconducting wires under simulated pulse magnet operations, (3) developing an analytical model for explaining the new AC-loss properties found in the experiment, and (4) developing a computational methodology for comparing AC losses of a superconducting wire with those of a cable for a superconducting pulse magnet. A new experimental system using an isothermal calorimetric method was designed and constructed to measure the absolute AC losses in a composite superconductor. This unique experimental setup is capable of measuring AC losses of a brittle Nb 3 Sn wire carrying high AC current in-phase with a large-amplitude pulse magnetic field. Improvements of the accuracy and the efficiency of this method are discussed. Three different types of composite wire have been measured: a Nb 3 Sn modified jelly-roll (MJR) internal-tin wire used in a prototype ohmic heating coil, a Nb 3 Sn internal-tin wire developed for a fusion reactor ohmic heating coil, and a NbTi wire developed for the magnets in a particle accelerator. The cross sectional constructions of these wires represent typical commercial wires manufactured for pulse magnet applications
DEFF Research Database (Denmark)
Liu, Wei; Nannarelli, Alberto
2008-01-01
A few classes of algorithms to implement division in hardware have been used over the years: division by digit-recurrence, by reciprocal approximation by iterative methods and by polynomial approximation. Due to the differences in the algorithms, a comparison among their implementation in terms o...... of performance and precision is sometimes hard to make. In this work, we use power dissipation and energy consumption as metrics to compare among those different classes of algorithms. There are no previous works in the literature presenting such a comparison....
Matthaeus, W. H.; Yang, Y.; Servidio, S.; Parashar, T.; Chasapis, A.; Roytershteyn, V.
2017-12-01
Turbulence cascade transfers energy from large scale to small scale but what happens once kinetic scales are reached? In a collisional medium, viscosity and resistivity remove fluctuation energy in favor of heat. In the weakly collisional solar wind, (or corona, m-sheath, etc.), the sequence of events must be different. Heating occurs, but through what mechanisms? In standard approaches, dissipation occurs though linear wave modes or instabilities and one seeks to identify them. A complementary view is that cascade leads to several channels of energy conversion, interchange and spatial rearrangement that collectively leads to production of internal energy. Channels may be described using compressible MHD & multispecies Vlasov Maxwell formulations. Key steps are: Conservative rearrangement of energy in space; Parallel incompressible and compressible cascades - conservative rearrangment in scale; electromagnetic work on particles that drives flows, both macroscopic and microscopic; and pressure-stress interactions, both compressive and shear-like, that produces internal energy. Examples given from MHD, PIC simulations and MMS observations. A more subtle issue is how entropy is related to this degeneration (or, "dissipation") of macroscopic, fluid-scale fluctuations. We discuss this in terms of Boltzmann and thermodynamic entropies, and velocity space effects of collisions.
Dissipation effects in mechanics and thermodynamics
Güémez, J.; Fiolhais, M.
2016-07-01
With the discussion of three examples, we aim at clarifying the concept of energy transfer associated with dissipation in mechanics and in thermodynamics. The dissipation effects due to dissipative forces, such as the friction force between solids or the drag force in motions in fluids, lead to an internal energy increase of the system and/or to heat transfer to the surroundings. This heat flow is consistent with the second law, which states that the entropy of the universe should increase when those forces are present because of the irreversibility always associated with their actions. As far as mechanics is concerned, the effects of the dissipative forces are included in Newton’s equations as impulses and pseudo-works.
Vibration and Energy Dissipation of Nanocomposite Laminates for Below Ballistic Impact Loading
Directory of Open Access Journals (Sweden)
G. Balaganesan
Full Text Available Abstract Composite laminates are made of glass woven roving mats of 610gsm, epoxy resin and nano clay which are subjected to projectile impact. Nano clay dispersion is varied from 1% to 5%. Impact tests are conducted in a gas gun setup with a spherical nose cylindrical projectile of diameter 9.5 mm of mass 7.6 g. The energy absorbed by the laminates when subjected to impact loading is studied, the velocity range is below ballistic limit. The effect of nano clay on energy absorption in vibration, delamination and matrix crack is studied for different weight % of nano clay and for different thickness values of the laminates. The natural frequencies and damping factors are obtained for the laminates during impact and the effect of nano clay is studied. The results show considerable improvement in energy absorption due to the presence of nano clay
Kim, Daehee; Kim, Hanul; Yun, Wan Soo; Watanabe, Kenji; Taniguchi, Takashi; Rho, Heesuk; Bae, Myung-Ho
2018-04-01
Understanding the energy transport by charge carriers and phonons in two-dimensional (2D) van der Waals heterostructures is essential for the development of future energy-efficient 2D nanoelectronics. Here, we performed in situ spatially resolved Raman thermometry on an electrically biased graphene channel and its hBN substrate to study the energy dissipation mechanism in graphene/hBN heterostructures. By comparing the temperature profile along the biased graphene channel with that along the hBN substrate, we found that the thermal boundary resistance between the graphene and hBN was in the range of (1-2) ~ × 10-7 m2 K W-1 from ~100 °C to the onset of graphene break-down at ~600 °C in air. Consideration of an electro-thermal transport model together with the Raman thermometry conducted in air showed that a doping effect occurred under a strong electric field played a crucial role in the energy dissipation of the graphene/hBN device up to T ~ 600 °C.
Energy flux due to electromagnetic fluctuations during guide field magnetic reconnection
International Nuclear Information System (INIS)
Kuwahata, Akihiro; Inomoto, Michiaki; Ono, Yasushi; Yanai, Ryoma
2016-01-01
Large electromagnetic fluctuations inside the current sheet and large reconnection electric fields are observed during fast magnetic reconnection in the presence of a guide field. The fluctuations transport 2.5% of the dissipated magnetic energy from the reconnection region. Although the energy gains of the ions and electrons are approximately 60% and 12%, respectively, of the dissipated magnetic energy after the fast reconnection, the energy of fluctuations is not comparable to their energy gains. The fluctuations do not directly contribute to the energy conversion but might cause the fast reconnection leading to the rapid release of magnetic energy. (author)
Lu, Guangtao; Feng, Qian; Li, Yourong; Wang, Hao; Song, Gangbing
2017-12-04
During the propagation of ultrasonic waves in structures, there is usually energy loss due to ultrasound energy diffusion and dissipation. The aim of this research is to characterize the ultrasound energy diffusion that occurs due to small-size damage on an aluminum plate using piezoceramic transducers, for the future purpose of developing a damage detection algorithm. The ultrasonic energy diffusion coefficient is related to the damage distributed in the medium. Meanwhile, the ultrasonic energy dissipation coefficient is related to the inhomogeneity of the medium. Both are usually employed to describe the characteristics of ultrasound energy diffusion. The existence of multimodes of Lamb waves in metallic plate structures results in the asynchronous energy transport of different modes. The mode of Lamb waves has a great influence on ultrasound energy diffusion as a result, and thus has to be chosen appropriately. In order to study the characteristics of ultrasound energy diffusion in metallic plate structures, an experimental setup of an aluminum plate with a through-hole, whose diameter varies from 0.6 mm to 1.2 mm, is used as the test specimen with the help of piezoceramic transducers. The experimental results of two categories of damages at different locations reveal that the existence of damage changes the energy transport between the actuator and the sensor. Also, when there is only one dominate mode of Lamb wave excited in the structure, the ultrasound energy diffusion coefficient decreases approximately linearly with the diameter of the simulated damage. Meanwhile, the ultrasonic energy dissipation coefficient increases approximately linearly with the diameter of the simulated damage. However, when two or more modes of Lamb waves are excited, due to the existence of different group velocities between the different modes, the energy transport of the different modes is asynchronous, and the ultrasonic energy diffusion is not strictly linear with the size of
Directory of Open Access Journals (Sweden)
Guangtao Lu
2017-12-01
Full Text Available During the propagation of ultrasonic waves in structures, there is usually energy loss due to ultrasound energy diffusion and dissipation. The aim of this research is to characterize the ultrasound energy diffusion that occurs due to small-size damage on an aluminum plate using piezoceramic transducers, for the future purpose of developing a damage detection algorithm. The ultrasonic energy diffusion coefficient is related to the damage distributed in the medium. Meanwhile, the ultrasonic energy dissipation coefficient is related to the inhomogeneity of the medium. Both are usually employed to describe the characteristics of ultrasound energy diffusion. The existence of multimodes of Lamb waves in metallic plate structures results in the asynchronous energy transport of different modes. The mode of Lamb waves has a great influence on ultrasound energy diffusion as a result, and thus has to be chosen appropriately. In order to study the characteristics of ultrasound energy diffusion in metallic plate structures, an experimental setup of an aluminum plate with a through-hole, whose diameter varies from 0.6 mm to 1.2 mm, is used as the test specimen with the help of piezoceramic transducers. The experimental results of two categories of damages at different locations reveal that the existence of damage changes the energy transport between the actuator and the sensor. Also, when there is only one dominate mode of Lamb wave excited in the structure, the ultrasound energy diffusion coefficient decreases approximately linearly with the diameter of the simulated damage. Meanwhile, the ultrasonic energy dissipation coefficient increases approximately linearly with the diameter of the simulated damage. However, when two or more modes of Lamb waves are excited, due to the existence of different group velocities between the different modes, the energy transport of the different modes is asynchronous, and the ultrasonic energy diffusion is not strictly
Chakraborty, S.
2017-12-01
The theory of generalized thermoelasticity in the context of the Green-Naghdi model -II (thermoelasticity without energy dissipation) is studied for an infinite circular cylindrical cavity subjected to two different cases of thermoelastic interactions when the radial stress is zero for (a) maintaining constant temperature and (b) temperature is varying exponentially with time. The Laplace transform from time variable is used to the governing equations to formulate a vector matrix differential equation which is then solved by the eigen value approach. Numerical computations for the displacement component, temperature distribution and components of thermal stress have been made and presented graphically.
Energy Technology Data Exchange (ETDEWEB)
Back, B.B.; Blumenthal, D.J.; Davids, C.N. [and others
1995-08-01
The fission hindrance of hot nuclei was deduced recently from an enhanced emission of GDR {gamma} rays, neutrons and charged particles prior to scission of heavy nuclei. In the most recent experiments addressing this topic, namely new measurements of the pre-scission {gamma} rays and evaporation residues from the {sup 32}S + {sup 184}W reaction, a rather sharp transition from negligible to full one-body dissipation occurs over the excitation energy region E{sub exc} = 60-100 MeV. However, the cross section does not appear to level out or start to decline again at the upper end of the energy range as expected in this interpretation. It is therefore clearly desirable to extend the excitation energy range to look for such an effect in order to either corroborate or refute this interpretation.
Energy Technology Data Exchange (ETDEWEB)
Guihot, P.; Revaud, D.
1996-04-01
This paper deals with the results of a bibliographic survey of energy dissipation devices which could be adapted for overhead cranes. The principle of passive devices using friction, yielding steel systems of viscous and viscoelastic systems are remembered. An active control system, which needs a minimum of external control energy is also presented. The application to overhead cranes which have a strong non linear behaviour under strong seismic motion (sliding between rails and wheels, local yielding and damage) is further discussed. The first results of a numerical study in progress are likewise purposed. The criterion of selection of the devices turn on the performance, the robustness and the reliability. The behaviour in the presence of non linearities, the sensitivity to the variations of the vibratory characteristics, and lastly the sensitivity to the response delay of the active controller are taken into account. (authors). 14 refs., 4 figs.
Directory of Open Access Journals (Sweden)
G. Meneghetti
2016-01-01
Full Text Available Fatigue crack initiation and propagation involve plastic strains that require some work to be done on the material. Most of this irreversible energy is dissipated as heat and consequently the material temperature increases. The heat being an indicator of the intense plastic strains occurring at the tip of a propagating fatigue crack, when combined with the Neuber’s structural volume concept, it might be used as an experimentally measurable parameter to assess the fatigue damage accumulation rate of cracked components. On the basis of a theoretical model published previously, in this work the heat energy dissipated in a volume surrounding the crack tip is estimated experimentally on the basis of the radial temperature profiles measured by means of an infrared camera. The definition of the structural volume in a fatigue sense is beyond the scope of the present paper. The experimental crack propagation tests were carried out on hot-rolled, 6-mm-thick AISI 304L stainless steel specimens subject to completely reversed axial fatigue loading.
Madami, Marco; Gubbiotti, Gianluca; Tacchi, Silvia; Carlotti, Giovanni
2017-11-01
Single- or multi-layered planar magnetic dots, with lateral dimensions ranging from tens to hundreds of nanometers, are used as elemental switches in current and forthcoming devices for information and communication technology (ICT), including magnetic memories, spin-torque oscillators and nano-magnetic logic gates. In this review article, we will first discuss energy dissipation during irreversible switching protocols of dots of different dimensions, ranging from a few tens of nanometers to the micrometric range. Then we will focus on the fundamental energy limits of adiabatic (slow) erasure and reversal of a magnetic nanodot, showing that dissipationless operation is achievable, provided that both dynamic reversibility (arbitrarily slow application of external fields) and entropic reversibility (no free entropy increase) are insured. However, recent theoretical and experimental tests of magnetic-dot erasure reveal that intrinsic defects related to materials imperfections such as roughness or polycrystallinity, may cause an excess of dissipation if compared to the minimum theoretical limit. We will conclude providing an outlook on the most promising strategies to achieve a new generation of power-saving nanomagnetic logic devices based on clusters of interacting dots and on straintronics.
Kosugi, Makiko; Miyake, Hirohisa; Yamakawa, Hisanori; Shibata, Yutaka; Miyazawa, Atsuo; Sugimura, Takashi; Satoh, Kazuhiko; Itoh, Shigeru; Kashino, Yasuhiro
2013-08-01
Lichens are drought-resistant symbiotic organisms of mycobiont fungi and photobiont green algae or cyanobacteria, and have an efficient mechanism to dissipate excess captured light energy into heat in a picosecond time range to avoid photoinhibition. This mechanism can be assessed as drought-induced non-photochemical quenching (d-NPQ) using time-resolved fluorescence spectroscopy. A green alga Trebouxia sp., which lives within a lichen Ramalina yasudae, is one of the most common green algal photobionts. This alga showed very efficient d-NPQ under desiccation within the lichen thallus, whereas it lost d-NPQ ability when isolated from R. yasudae, indicating the importance of the interaction with the mycobiont for d-NPQ ability. We analyzed the water extracts from lichen thalli that enhanced d-NPQ in Trebouxia. Of several sugar compounds identified in the water extracts by nuclear magnetic resonance (NMR), mass spectrometry (MS) and gas chromatography (GC) analyses, only d-arabitol recovered d-NPQ in isolated Trebouxia to a level similar to that detected for R. yasudae thallus. Other sugar compounds did not help the expression of d-NPQ at the same concentrations. Thus, arabitol is essential for the expression of d-NPQ to dissipate excess captured light energy into heat, protecting the photobiont from photoinhibition. The relationship between mycobionts and photobionts is, therefore, not commensalism, but mutualism with each other, as shown by d-NPQ expression.
Energy Technology Data Exchange (ETDEWEB)
Vlaykov, Dimitar G., E-mail: Dimitar.Vlaykov@ds.mpg.de [Institut für Astrophysik, Universität Göttingen, Friedrich-Hund-Platz 1, D-37077 Göttingen (Germany); Max-Planck-Institut für Dynamik und Selbstorganisation, Am Faßberg 17, D-37077 Göttingen (Germany); Grete, Philipp [Institut für Astrophysik, Universität Göttingen, Friedrich-Hund-Platz 1, D-37077 Göttingen (Germany); Max-Planck-Institut für Sonnensystemforschung, Justus-von-Liebig-Weg 3, D-37077 Göttingen (Germany); Schmidt, Wolfram [Hamburger Sternwarte, Universität Hamburg, Gojenbergsweg 112, D-21029 Hamburg (Germany); Schleicher, Dominik R. G. [Departamento de Astronomía, Facultad Ciencias Físicas y Matemáticas, Universidad de Concepción, Av. Esteban Iturra s/n Barrio Universitario, Casilla 160-C (Chile)
2016-06-15
Compressible magnetohydrodynamic (MHD) turbulence is ubiquitous in astrophysical phenomena ranging from the intergalactic to the stellar scales. In studying them, numerical simulations are nearly inescapable, due to the large degree of nonlinearity involved. However, the dynamical ranges of these phenomena are much larger than what is computationally accessible. In large eddy simulations (LESs), the resulting limited resolution effects are addressed explicitly by introducing to the equations of motion additional terms associated with the unresolved, subgrid-scale dynamics. This renders the system unclosed. We derive a set of nonlinear structural closures for the ideal MHD LES equations with particular emphasis on the effects of compressibility. The closures are based on a gradient expansion of the finite-resolution operator [W. K. Yeo (CUP, 1993)] and require no assumptions about the nature of the flow or magnetic field. Thus, the scope of their applicability ranges from the sub- to the hyper-sonic and -Alfvénic regimes. The closures support spectral energy cascades both up and down-scale, as well as direct transfer between kinetic and magnetic resolved and unresolved energy budgets. They implicitly take into account the local geometry, and in particular, the anisotropy of the flow. Their properties are a priori validated in Paper II [P. Grete et al., Phys. Plasmas 23, 062317 (2016)] against alternative closures available in the literature with respect to a wide range of simulation data of homogeneous and isotropic turbulence.
Valente, Pedro C.; da Silva, Carlos B.; Pinho, Fernando T.
2013-11-01
We report a numerical study of statistically steady and decaying turbulence of FENE-P fluids for varying polymer relaxation times ranging from the Kolmogorov dissipation time-scale to the eddy turnover time. The total turbulent kinetic energy dissipation is shown to increase with the polymer relaxation time in both steady and decaying turbulence, implying a ``drag increase.'' If the total power input in the statistically steady case is kept equal in the Newtonian and the viscoelastic simulations the increase in the turbulence-polymer energy transfer naturally lead to the previously reported depletion of the Newtonian, but not the overall, kinetic energy dissipation. The modifications to the nonlinear energy cascade with varying Deborah/Weissenberg numbers are quantified and their origins investigated. The authors acknowledge the financial support from Fundação para a Ciência e a Tecnologia under grant PTDC/EME-MFE/113589/2009.
Ishida, Satoshi; Morita, Ken-ichi; Kishine, Masahiro; Takabayashi, Atsushi; Murakami, Reiko; Takeda, Satomi; Shimamoto, Ko; Sato, Fumihiko; Endo, Tsuyoshi
2011-10-01
The thermal dissipation (TD) of absorbed light energy in PSII is considered to be an important photoprotection process in photosynthesis. A major portion of TD has been visualized through the analysis of Chl fluorescence as energy quenching (qE) which depends on the presence of the PsbS subunit. Although the physiological importance of qE-associated TD (qE-TD) has been widely accepted, it is not yet clear how much of the absorbed light energy is dissipated through a qE-associated mechanism. In this study, the fates of absorbed light energy in PSII with regard to different TD processes, including qE-TD, were quantitatively estimated by the typical energy allocation models using transgenic rice in which psbS genes were silenced by RNA interference (RNAi). The silencing of psbS genes resulted in a decrease in the light-inducible portion of TD, whereas the allocation of energy to electron transport did not change over a wide range of light intensities. The allocation models indicate that the energy allocated to qE-TD under saturating light is 30-50%. We also showed that a large portion of absorbed light energy is thermally dissipated in manners that are independent of qE. The nature of such dissipations is discussed.
Huarancca Reyes, Thais; Scartazza, Andrea; Lu, Yu; Yamaguchi, Junji; Guglielminetti, Lorenzo
2016-08-01
Carbon (C) and nitrogen (N) nutrient sources are essential elements for metabolism, and their availability must be tightly coordinated for the optimal growth and development in plants. Plants are able to sense and respond to different C/N conditions via specific partitioning of C and N sources and the regulation of a complex cellular metabolic activity. We studied how the interaction between C and N signaling could affect carbohydrate metabolism, soluble sugar levels, photochemical efficiency of photosystem II (PSII) and the ability to drive the excess energy in Arabidopsis seedlings under moderated and disrupted C/N-nutrient conditions. Invertase and sucrose synthase activities were markedly affected by C/N-nutrient status depending on the phosphorylation status, suggesting that these enzymes may necessarily be modulated by their direct phosphorylation or phosphorylation of proteins that form complex with them in response to C/N stress. In addition, the enzymatic activity of these enzymes was also correlated with the amount of sugars, which not only act as substrate but also as signaling compounds. Analysis of chlorophyll fluorescence in plants under disrupted C/N condition suggested a reduction of electron transport rate at PSII level associated with a higher capacity for non-radiative energy dissipation in comparison with plants under moderated C/N condition. In conclusion, the tight coordination between C and N not only affects the carbohydrates metabolism and their concentration within plant tissues, but also the partitioning of the excitation energy at PSII level between radiative (electron transport) and non-radiative (heat) dissipation pathways. Copyright © 2016 Elsevier Masson SAS. All rights reserved.
Impact of Energy Losses Due to Failures on Photovoltaic Plant Energy Balance
Isidoro Lillo-Bravo; Pablo González-Martínez; Miguel Larrañeta; José Guasumba-Codena
2018-01-01
Photovoltaic (PV) plant failures have a significant influence on PV plant security, reliability, and energy balance. Energy losses produced by a PV plant are due to two large causes: failures and inefficiencies. Knowing the relative influence of energy losses due to failures and energy losses due to inefficiencies on the PV plant energy balance contribute to the optimization of its design, commissioning, and maintenance tasks. This paper estimates the failure rates, grouped by components, and...
Blanchard, Antoine; Bergman, Lawrence A.; Vakakis, Alexander F.
2017-07-01
We computationally investigate the dynamics of a linearly-sprung circular cylinder immersed in an incompressible flow and undergoing transverse vortex-induced vibration (VIV), to which is attached a rotational nonlinear energy sink (NES) consisting of a mass that freely rotates at constant radius about the cylinder axis, and whose motion is restrained by a rotational linear viscous damper. The inertial coupling between the rotational motion of the attached mass and the rectilinear motion of the cylinder is ;essentially nonlinear;, which, in conjunction with dissipation, allows for one-way, nearly irreversible targeted energy transfer (TET) from the oscillating cylinder to the nonlinear dissipative attachment. At the intermediate Reynolds number Re = 100, the NES-equipped sprung cylinder undergoes repetitive cycles of slowly decaying oscillations punctuated by intervals of chaotic instabilities. During the slowly decaying portion of each cycle, the dynamics of the cylinder is regular and, for large enough values of the ratio ε of the NES mass to the total mass (i.e., NES mass plus cylinder mass), can lead to significant vortex street elongation with partial stabilization of the wake. As ε approaches zero, no such vortex elongation is observed and the wake patterns appear similar to that for a sprung cylinder with no NES. We apply proper orthogonal decomposition (POD) to the velocity flow field during a slowly decaying portion of the solution and show that, in situations where vortex elongation occurs, the NES, though not in direct contact with the surrounding fluid, has a drastic effect on the underlying flow structures, imparting significant and continuous passive redistribution of energy among POD modes. We construct a POD-based reduced-order model for the lift coefficient to characterize energy transactions between the fluid and the cylinder throughout the slowly decaying cycle. We introduce a quantitative signed measure of the work done by the fluid on the
Adams, J; Fantner, G E; Fisher, L W; Hansma, P K
2008-01-01
The fracture resistance of biomineralized tissues such as bone, dentin, and abalone is greatly enhanced through the nanoscale interactions of stiff inorganic mineral components with soft organic adhesive components. A proper understanding of the interactions that occur within the organic component, and between the organic and inorganic components, is therefore critical for a complete understanding of the mechanics of these tissues. In this paper, we use Atomic Force Microscope (AFM) force spectroscopy and dynamic force spectroscopy to explore the effect of ionic interactions within a nanoscale system consisting of networks of Dentin Matrix Protein 1 (DMP1) (a component of both bone and dentin organic matrix), a mica surface, and an AFM tip. We find that DMP1 is capable of dissipating large amounts of energy through an ion-mediated mechanism, and that the effectiveness increases with increasing ion valence. PMID:18843380
Energy Technology Data Exchange (ETDEWEB)
Adams, J; Fantner, G E; Hansma, P K [Department of Physics, Broida Hall, University of California, Santa Barbara, CA 93106 (United States); Fisher, L W [Craniofacial and Skeletal Diseases Branch, NIDCR, NIH, DHHS, Bethesda, MD 20892 (United States)], E-mail: adams@physics.ucsb.edu, E-mail: fantner@physics.ucsb.edu, E-mail: lfisher@dir.nidcr.nih.gov, E-mail: prasant@physics.ucsb.edu
2008-09-24
The fracture resistance of biomineralized tissues such as bone, dentin, and abalone is greatly enhanced through the nanoscale interactions of stiff inorganic mineral components with soft organic adhesive components. A proper understanding of the interactions that occur within the organic component, and between the organic and inorganic components, is therefore critical for a complete understanding of the mechanics of these tissues. In this paper, we use atomic force microscope (AFM) force spectroscopy and dynamic force spectroscopy to explore the effect of ionic interactions within a nanoscale system consisting of networks of dentin matrix protein 1 (DMP1) (a component of both bone and dentin organic matrix), a mica surface and an AFM tip. We find that DMP1 is capable of dissipating large amounts of energy through an ion-mediated mechanism, and that the effectiveness increases with increasing ion valence.
Chen, Zhihao; Schellart, Wouter P.; Duarte, João C.
2015-01-01
In a subduction system the force and the energy required to deform the overriding plate are generally thought to come from the negative buoyancy of the subducted slab and its potential energy, respectively. Such deformation might involve extension and back-arc basin formation or shortening and
Characteristic energy range of electron scattering due to plasmaspheric hiss
Ma, Q.; Li, W.; Thorne, R. M.; Bortnik, J.; Reeves, G. D.; Kletzing, C. A.; Kurth, W. S.; Hospodarsky, G. B.; Spence, H. E.; Baker, D. N.; Blake, J. B.; Fennell, J. F.; Claudepierre, S. G.; Angelopoulos, V.
2016-12-01
We investigate the characteristic energy range of electron flux decay due to the interaction with plasmaspheric hiss in the Earth's inner magnetosphere. The Van Allen Probes have measured the energetic electron flux decay profiles in the Earth's outer radiation belt during a quiet period following the geomagnetic storm that occurred on 7 November 2015. The observed energy of significant electron decay increases with decreasing L shell and is well correlated with the energy band corresponding to the first adiabatic invariant μ = 4-200 MeV/G. The electron diffusion coefficients due to hiss scattering are calculated at L = 2-6, and the modeled energy band of effective pitch angle scattering is also well correlated with the constant μ lines and is consistent with the observed energy range of electron decay. Using the previously developed statistical plasmaspheric hiss model during modestly disturbed periods, we perform a 2-D Fokker-Planck simulation of the electron phase space density evolution at L = 3.5 and demonstrate that plasmaspheric hiss causes the significant decay of 100 keV-1 MeV electrons with the largest decay rate occurring at around 340 keV, forming anisotropic pitch angle distributions at lower energies and more flattened distributions at higher energies. Our study provides reasonable estimates of the electron populations that can be most significantly affected by plasmaspheric hiss and the consequent electron decay profiles.
Energy Loss in Pulse Detonation Engine due to Fuel Viscosity
Directory of Open Access Journals (Sweden)
Weipeng Hu
2014-01-01
Full Text Available Fluid viscosity is a significant factor resulting in the energy loss in most fluid dynamical systems. To analyze the energy loss in the pulse detonation engine (PDE due to the viscosity of the fuel, the energy loss in the Burgers model excited by periodic impulses is investigated based on the generalized multisymplectic method in this paper. Firstly, the single detonation energy is simplified as an impulse; thus the complex detonation process is simplified. And then, the symmetry of the Burgers model excited by periodic impulses is studied in the generalized multisymplectic framework and the energy loss expression is obtained. Finally, the energy loss in the Burgers model is investigated numerically. The results in this paper can be used to explain the difference between the theoretical performance and the experimental performance of the PDE partly. In addition, the analytical approach of this paper can be extended to the analysis of the energy loss in other fluid dynamic systems due to the fluid viscosity.
Aucique-Pérez, Carlos Eduardo; de Menezes Silva, Paulo Eduardo; Moreira, Wiler Ribas; DaMatta, Fábio Murilo; Rodrigues, Fabrício Ávila
2017-12-01
Considering the effect of silicon (Si) in reducing the blast symptoms on wheat in a scenario where the losses in the photosynthetic capacity of the infected plants is lowered, this study investigated the ability of using the incident light, the chloroplastidic pigments (chlorophylls and carotenoids) alterations and the possible role of carotenoids on the process of light dissipation on wheat plants non-supplied (-Si) or supplied (+Si) with Si and inoculated or not with Pyricularia oryzae. For + Si plants, blast severity was reduced compared to -Si plants. Reductions in the concentration of photosynthetic pigments (total chlorophyll, violanxanthin + antheraxanthin + zeaxanthin, β-carotene and lutein) were greater for inoculated -Si plants than for inoculated + Si ones. The α-carotene concentration increased for inoculated -Si and +Si plants in comparison to non-inoculated plants limiting, therefore, lutein production. Higher functional damage to the photosystem II (PSII) was noticed for inoculated -Si plants with reductions in the values of maximum quantum quenching, photochemical yield of PSII and electron transport rate, but higher values for quenching non-photochemical. This finding also contributed to reductions in the values of light saturated rate photosynthesis and light saturation point for -Si plants which was attenuated for inoculated + Si plants. Increase in dark respiration values occurred for inoculated plants than for non-inoculated ones. The Si supply to wheat plants, besides reducing blast severity, contributed to their better photosynthetic performance. Moreover, inoculated + Si plants coped with drastic losses of light energy dissipation processes (fluorescence and heat) by increasing the concentration of carotenoids which helped to maintain the structural and functional viability of the photosynthetic machinery minimizing, therefore, lipid peroxidation and the production of reactive oxygen species. Copyright © 2017 Elsevier Masson
Hao, Guang-You; Wang, Ai-Ying; Liu, Zhi-Hui; Franco, Augusto C; Goldstein, Guillermo; Cao, Kun-Fang
2011-06-01
Hemiepiphytic Ficus species (Hs) possess traits of more conservative water use compared with non-hemiepiphytic Ficus species (NHs) even during their terrestrial growth phase, which may result in significant differences in photosynthetic light use between these two growth forms. Stem hydraulic conductivity, leaf gas exchange and chlorophyll fluorescence were compared in adult trees of five Hs and five NHs grown in a common garden. Hs had significantly lower stem hydraulic conductivity, lower stomatal conductance and higher water use efficiency than NHs. Photorespiration played an important role in avoiding photoinhibition at high irradiance in both Hs and NHs. Under saturating irradiance levels, Hs tended to dissipate a higher proportion of excessive light energy through thermal processes than NHs, while NHs dissipated a larger proportion of electron flow than Hs through the alternative electron sinks. No significant difference in maximum net CO2 assimilation rate was found between Hs and NHs. Stem xylem hydraulic conductivity was positively correlated with maximum electron transport rate and negatively correlated with the quantum yield of non-photochemical quenching across the 10 studied Ficus species. These findings indicate that a canopy growth habit during early life stages in Hs of Ficus resulted in substantial adaptive differences from congeneric NHs not only in water relations but also in photosynthetic light use and carbon economy. The evolution of epiphytic growth habit, even for only part of their life cycle, involved profound changes in a suite of inter-correlated ecophysiological traits that persist to a large extent even during the later terrestrial growth phase.
Esters, L. T.; Ward, B.; Sutherland, G.; Ten Doeschate, A.; Landwehr, S.; Bell, T. G.; Christensen, K. H.
2016-02-01
The air-sea exchange of heat, gas and momentum plays an important role for the Earth's weather and global climate. The exchange processes between ocean and atmosphere are influenced by the prevailing surface ocean dynamics. This surface ocean is a highly turbulent region where there is enhanced production of turbulent kinetic energy (TKE). The dissipation rate of TKE (ɛ) in the surface ocean is an important process for governing the depth of both the mixing and mixed layers, which are important length-scales for many aspects of ocean research. However, there exist very limited observations of ɛ under open ocean conditions and consequently our understanding of how to model the dissipation profile is very limited. The approaches to model profiles of ɛ that exist, differ by orders of magnitude depending on their underlying theoretical assumption and included physical processes. Therefore, scaling ɛ is not straight forward and requires open ocean measurements of ɛ to validate the respective scaling laws. This validated scaling of ɛ, is for example required to produce accurate mixed layer depths in global climate models. Errors in the depth of the ocean surface boundary layer can lead to biases in sea surface temperature. Here, we present open ocean measurements of ɛ from the Air-Sea Interaction Profiler (ASIP) collected during several cruises in different ocean basins. ASIP is an autonomous upwardly rising microstructure profiler allowing undisturbed profiling up to the ocean surface. These direct measurements of ɛ under various types of atmospheric and oceanic conditions along with measurements of atmospheric fluxes and wave conditions allow us to make a unique assessment of several scaling approaches based on wind, wave and buoyancy forcing. This will allow us to best assess the most appropriate ɛ-based parameterisation for air-sea exchange.
Dissipative relativistic hydrodynamics
International Nuclear Information System (INIS)
Imshennik, V.S.; Morozov, Yu.I.
1989-01-01
Using the comoving reference frame in the general non-inertial case, the relativistic hydrodynamics equations are derived with an account for dissipative effects in the matter. From the entropy production equation, the exact from for the dissipative tensor components is obtained. As a result, the closed system of equations of dissipative relativistic hydrodynamics is obtained in the comoving reference frame as a relativistic generalization of the known Navier-Stokes equations for Lagrange coordinates. Equations of relativistic hydrodynamics with account for dissipative effects in the matter are derived using the assocoated reference system in general non-inertial case. True form of the dissipative tensor components is obtained from entropy production equation. Closed system of equations for dissipative relativistic hydrodynamics is obtained as a result in the assocoated reference system (ARS) - relativistic generalization of well-known Navier-Stokes equations for Lagrange coordinates. Equation system, obtained in this paper for ARS, may be effectively used in numerical models of explosive processes with 10 51 erg energy releases which are characteristic for flashes of supernovae, if white dwarf type compact target suggested as presupernova
Driever, S.M.; Baker, N.R.
2011-01-01
Electron flux from water via photosystem II (PSII) and PSI to oxygen (water–water cycle) may provide a mechanism for dissipation of excess excitation energy in leaves when CO2 assimilation is restricted. Mass spectrometry was used to measure O2 uptake and evolution together with CO2 uptake in leaves
International Nuclear Information System (INIS)
Chernousenko, V.M.; Kuklin, V.M.; Panachenko, I.P.; Vorob'yov, V.M.
1990-01-01
This paper reports on a wide spectrum of oscillations that is excited due to the evolution instabilities, being in a weak above-threshold state, in the inequilibrium media with decaying spectrum. In this case the pumping, whose part is played by an intensive wave or occupation inversion in the active medium, synchronized the phases of excited modes and, thus, forms the space dissipative structure of the field. In dissipative nonlinear media with nondecaying spectrum the space structures, formed due to the development of instability, experience small-scale hexagonal modulation
Interphasial energy transfer and particle dissipation in particle-laden wall turbulence
Zhao, L.; Andersson, H.I.; Gillissen, J.J.J.
2013-01-01
Transfer of mechanical energy between solid spherical particles and a Newtonian carrier fluid has been explored in two-way coupled direct numerical simulations of turbulent channel flow. The inertial particles have been treated as individual point particles in a Lagrangian framework and their
The fusion of membranes and vesicles: pathway and energy barriers from Dissipative Particle Dynamics
DEFF Research Database (Denmark)
Shillcock, Julian C.
2009-01-01
are simulated using the optimized parameter set. In the observed fusion pathway, configurations of individual lipids play an important role. Fusion starts with individual lipids assuming a splayed tail configuration with one tail inserted in each membrane. To determine the corresponding energy barrier, we...
Marini, John J
2018-02-01
To describe and put into context recent conceptual advances regarding the relationship of energy load and power to ventilator-induced lung injury (VILI). Investigative emphasis regarding VILI has almost exclusively centered on the static characteristics of the individual tidal cycle - tidal volume, plateau pressure, positive end-expiratory pressure, and driving pressure. Although those static characteristics of the tidal cycle are undeniably important, the 'dynamic' characteristics of ventilation must not be ignored. To inflict the nonrupturing damage we identify as VILI, work must be performed and energy expended by high stress cycles applied at rates that exceed the capacity of endogenous repair. Machine power, the pace at which the work performing energy load is applied by the ventilator, has received increasing scrutiny as a candidate for the proximate and integrative cause of VILI. Although the unmodified values of machine-delivered energy or power (which are based on airway pressures and tidal volumes) cannot serve unconditionally as a rigid and quantitative guide to ventilator adjustment for lung protection, bedside consideration of the dynamics of ventilation and potential for ergotrauma represents a clear conceptual advance that complements the static parameters of the individual tidal cycle that with few exceptions have held our scientific attention.
Attractors of dissipative structure in three dissipative fluids
International Nuclear Information System (INIS)
Kondoh, Yoshiomi
1993-10-01
A general theory with use of auto-correlations for distributions is presented to derive that realization of coherent structures in general dissipative dynamic systems is equivalent to that of self-organized states with the minimum dissipation rate for instantaneously contained energy. Attractors of dissipative structure are shown to be given by eigenfunctions for dissipative dynamic operators of the dynamic system and to constitute the self-organized and self-similar decay phase. Three typical examples applied to incompressible viscous fluids, to incompressible viscous and resistive magnetohydrodynamic (MHD) fluids and to compressible resistive MHD plasmas are presented to lead to attractors in the three dissipative fluids and to describe a common physical picture of self-organization and bifurcation of the dissipative structure. (author)
Impact and Energy Dissipation Characteristics of Squeeze and Die Cast Magnesium Alloy AM60
DiCecco, Sante; Hu, Henry; Altenhof, William
High-pressure die cast (HPDC) magnesium alloy AM60 is recognized for its versatility in the manufacturing of weight sensitive components of relatively thin cross section. To further expand practical applications of the alloy, squeeze casting has been proposed to allow for thicker castings. In this study, AM60 alloy specimens of 10mm thickness were squeeze cast using a hydraulic press with an applied pressure of 60 MPa. Fracture energies, following a Charpy Impact Testing protocol, of the squeeze cast specimens were characterized in comparison with the HPDC counterparts using both experimental and numerical techniques. The experimental results show the squeeze cast alloy absorbing approximately 46.2% more energy during impact than its HPDC counterpart. Scanning electron microscopy fractography reveals the favourable quasi-cleavage fracture mode of the squeeze cast alloy AM60, relative to the decohesive rupture fracture mode present in the die cast alloy.
Peguero-Pina, José Javier; Gil-Pelegrín, Eustaquio; Morales, Fermín
2013-04-01
Under excess light, the efficient PSII light-harvesting antenna is switched into a photoprotected state in which potentially harmful absorbed energy is thermally dissipated. Changes occur rapidly and reversibly, enhanced by de-epoxidation of violaxanthin (V) to zeaxanthin (Z). This process is usually measured as non-photochemical quenching (NPQ) of chlorophyll (Chl) fluorescence. Using instrumentation for instantaneous leaf freezing, NPQ, spectral reflectance, and interconversions within the xanthophyll cycle with time resolution of seconds were recorded from Quercus coccifera leaves during low light (LL) to high light (HL) transitions, followed by relaxation at LL. During the first 30 s of both the LL to HL and HL to LL transitions, no activity of the xanthophyll cycle was detected, whereas 70-75% of the NPQ was formed and relaxed, respectively, by that time, the latter being traits of a rapidly reversible photoprotective energy dissipation. Three different Z pools were identified, which play different roles in energy dissipation and photoprotection. In conclusion, ΔpH was crucial to NPQ formation and relaxation in Q. coccifera during light transitions. Only a minor fraction of Z was associated to quenching, whereas the largest Z pool was not related to thermal dissipation. The latter is proposed to participate in photoprotection acting as antioxidant.
International Nuclear Information System (INIS)
Virk, K; Marsh, M; Monti, A; Trehard, T; Hazra, K; Boba, K; Remillat, C D L; Scarpa, F; Farrow, I R
2013-01-01
The work describes the manufacturing, testing and parametric analysis of cellular structures exhibiting zero Poisson’s ratio-type behaviour, together with zero and negative stiffness effects. The cellular structures are produced in flat panels and curved configurations, using a combination of rapid prototyping techniques and Kirigami (Origami and cutting) procedures for PEEK (Polyether Ether Ketone) thermoplastic composites. The curved cellular configurations show remarkable large deformation behaviours, with zero and negative stiffness regimes depending also on the strain rate applied. These unusual stiffness characteristics lead to a large increase of energy absorption during cyclic tests. (paper)
Tidal dissipation in the subsurface ocean of Enceladus
Matsuyama, I.; Hay, H.; Nimmo, F.; Kamata, S.
2017-12-01
Icy satellites of the outer solar system have emerged as potential habitable worlds due to the presence of subsurface oceans. As a long-term energy source, tidal heating in these oceans can influence the survivability of subsurface oceans, and the thermal, rotational, and orbital evolution of these satellites. Additionally, the spatial and temporal variation of tidal heating has implications for the interior structure and spacecraft observations. Previous models for dissipation in thin oceans are not generally applicable to icy satellites because either they ignore the presence of an overlying solid shell or use a thin shell membrane approximation. We present a new theoretical treatment for tidal dissipation in thin oceans with overlying shells of arbitrary thickness and apply it to Enceladus. The shell's resistance to ocean tides increases with shell thickness, reducing tidal dissipation as expected. Both the magnitude of energy dissipation and the resonant ocean thicknesses decrease as the overlying shell thickness increases, as previously shown using a membrane approximation. In contrast to previous work based on the traditional definition of the tidal quality factor, Q, our new definition is consistent with higher energy dissipation for smaller Q, and introduces a lower limit on Q. The dissipated power and tides are not in phase with the forcing tidal potential due to the delayed ocean response. The phase lag depends on the Rayleigh friction coefficient and ocean and shell thicknesses, which implies that phase lag observations can be used to constrain these parameters. Eccentricity heating produces higher dissipation near the poles, while obliquity heating produces higher dissipation near the equator, in contrast to the dissipation patterns in the shell. The time-averaged surface distribution of tidal heating can generate lateral shell thickness variations, providing an additional constraint on the Rayleigh friction coefficient. Explaining the endogenic power
Kim, Eunchul; Akimoto, Seiji; Tokutsu, Ryutaro; Yokono, Makio; Minagawa, Jun
2017-11-17
In green algae, light-harvesting complex stress-related 3 (LHCSR3) is responsible for the pH-dependent dissipation of absorbed light energy, a function vital for survival under high-light conditions. LHCSR3 binds the photosystem II and light-harvesting complex II (PSII-LHCII) supercomplex and transforms it into an energy-dissipative form under acidic conditions, but the molecular mechanism remains unclear. Here we show that in the green alga Chlamydomonas reinhardtii , LHCSR3 modulates the excitation energy flow and dissipates the excitation energy within the light-harvesting complexes of the PSII supercomplex. Using fluorescence decay-associated spectra analysis, we found that, when the PSII supercomplex is associated with LHCSR3 under high-light conditions, excitation energy transfer from light-harvesting complexes to chlorophyll-binding protein CP43 is selectively inhibited compared with that to CP47, preventing excess excitation energy from overloading the reaction center. By analyzing femtosecond up-conversion fluorescence kinetics, we further found that pH- and LHCSR3-dependent quenching of the PSII-LHCII-LHCSR3 supercomplex is accompanied by a fluorescence emission centered at 684 nm, with a decay time constant of 18.6 ps, which is equivalent to the rise time constant of the lutein radical cation generated within a chlorophyll-lutein heterodimer. These results suggest a mechanism in which LHCSR3 transforms the PSII supercomplex into an energy-dissipative state and provide critical insight into the molecular events and characteristics in LHCSR3-dependent energy quenching. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.
Atmospheric considerations regarding the impact of heat dissipation from a nuclear energy center
International Nuclear Information System (INIS)
Rotty, R.M.; Bauman, H.; Bennett, L.L.
1976-05-01
Potential changes in climate resulting from a large nuclear energy center are discussed. On a global scale, no noticeable changes are likely, but on both a regional and a local scale, changes can be expected. Depending on the cooling system employed, the amount of fog may increase, the amount and distribution of precipitation will change, and the frequency or location of severe storms may change. Very large heat releases over small surface areas can result in greater atmospheric instability; a large number of closely spaced natural-draft cooling towers have this disadvantage. On the other hand, employment of natural-draft towers makes an increase in the occurrence of ground fog unlikely. The analysis suggests that the cooling towers for a large nuclear energy center should be located in clusters of four with at least 2.5-mile spacing between the clusters. This is equivalent to the requirement of one acre of land surface per each two megawatts of heat being rejected
A new placement optimization method for viscoelastic dampers: Energy dissipation method
Qu, Ji-Ting
2012-09-01
A new mathematic model of location optimization for viscoelastic dampers is established through energy analysis based on force analogy method. Three working conditions (three lower limits of the new location index) as well as four ground motions are considered in this study, using MATLAB and SAP2000 in programming and verifying. This paper deals with the optimal placement of viscoelastic dampers and step-by-step time history analyses are carried out. Numerical analysis is illustrated to verify the effectiveness and feasibility of the new mathematic model for structural control. In addition, not only the optimal placement method using force analogy method can confirm dampers' locations all at once and be accurate to each span, but also it is without circular calculating. At last, a few helpful conclusions on viscoelastic dampers' optimal placement are made.
Elastic energy dissipation oxygen mobility and structural stability in YBa2Cu3O7-x
International Nuclear Information System (INIS)
Bonetti, E.; Campari, E.G.; Luprano, V.; Mantovani, S.; Casagrande, S.; Cammarota, P.
1993-01-01
Internal friction and dynamic Youngs modulus measurements have been performed by the vibrating reed technique in the 10 2 -10 4 Hz and at lower frequencies 1-30 Hz by an inverted torsional pendulum, on polycristalline YBa 2 Cu 3 O 7-x samples in the temperature range 300-900 K. Two relaxation damping peaks with 1.3±0.2 and 1.55±0.09 eV activation energies have been found. The relaxation strength depends on temperature and on the oxygen stoichiometry. A strong modulus softening indicative of a phase transition, is experienced for x=0.55 both in isothermal modulus measurements and during test at constant heating rate, when DTG measurements show correspondingly a maximum in the oxygen desorption rate. On the basis of the experimental results a model for the oxygen short range mobility, twinned interface mobility and oxygen out diffusion is presented and discussed. (orig.)
Radiant energy dissipation during final storage of high-level radioactive waste in rock salt
International Nuclear Information System (INIS)
Ramthun, H.
1981-08-01
A final disposal concept is assumed where the high-active waste from 1400 t of uranium, remaining after conditioning, is solidified in borosilicate glass and distributed in 1.760 waste casks. These containers 1.2 m in height and 0.3 m in diameter are to be buried 10 years after the fuel is removed from the reactor in the 300 m deep boreholes of a salt dome. For this design the mean absorbed dose rates are calculated in the glass die (3.9 Gy/s), the steel mantle (0.26 Gy/s) and in the salt rock (0.12 Gy/s at a distance of 1 cm and 0.034 Gy/s at a distance of 9 cm from the container surface) valid at the beginning of disposal. The risk involved with these amounts of stored lattice energy is shortly discussed. (orig.) [de
Directory of Open Access Journals (Sweden)
Silvia Meniconi
2018-02-01
Full Text Available In the last decades several reliable technologies have been proposed for fault detection in water distribution networks (DNs, whereas there are some limitations for transmission mains (TMs. For TM inspection, the most common fault detection technologies are of inline types—with sensors inserted into the pipelines—and then more expensive with respect to those used in DNs. An alternative to in-line sensors is given by transient test-based techniques (TTBTs, where pressure waves are injected in pipes “to explore” them. On the basis of the results of some tests, this paper analyses the relevance of the system configuration, energy dissipation phenomena, and pipe material characteristics in the transient behavior of a real TM. With this aim, a numerical model has been progressively refined not only in terms of the governing equations but also by including a more and more realistic representation of the system layout and taking into account the actual functioning conditions. As a result, the unexpected role of the minor branches—i.e., pipes with a length smaller than the 1% of the length of the main pipe—is pointed out and a preliminary criterion for the system skeletonization is offered. Moreover, the importance of both unsteady friction and viscoelasticity is evaluated as well as the remarkable effects of small defects is highlighted.
The effects of LT-SN on energy dissipation and lifetime in wireless sensor networks
Directory of Open Access Journals (Sweden)
Zeydin Pala
2016-11-01
Full Text Available Wireless sensor networks (WSNs still attract the attention of researchers, users and the private sector despite their low power and low range tendency for malfunction. This attraction towards WSNs results from their low cost structure and the solutions they offer for many prevalent problems. Many conditions, which remain unforeseen or unexpected during the design of the system, may arise after the initialization of the system. Similarly, many situations where security vulnerabilities take place may emerge in time in WSNs operating normally. In this study, we called nodes which enter sleeping mode without any further waking up and causing a sparser number of nodes in the network without any function in data transmission as Long-Term Sleep Nodes (LT-SN; and considered energy spaces caused by such nodes as a problem; and established two Linear Programming (LP models based on the efficiency of the present nodes. We offered two different models which present the effect of sensor nodes, which were initially operating in wireless sensor network environment and did not wake up following sleep mode, on network lifetime. The results of the present study report that as the number of LT-SN increases, the lifetime of the network decreases.
Directory of Open Access Journals (Sweden)
Surajit Chattopadhyay
2016-01-01
Full Text Available This paper reports a study on the truncated Israel-Stewart formalism for bulk viscosity using the extended holographic Ricci dark energy (EHRDE. Under the consideration that the universe is dominated by EHRDE, the evolution equation for the bulk viscous pressure Π in the framework of the truncated Israel-Stewart theory has been taken as τΠ˙+Π=-3ξH, where τ is the relaxation time and ξ is the bulk viscosity coefficient. Considering effective pressure as a sum of thermodynamic pressure of EHRDE and bulk viscous pressure, it has been observed that under the influence of bulk viscosity the EoS parameter wDE is behaving like phantom, that is, wDE≤-1. It has been observed that the magnitude of the effective pressure peff=p+Π is decaying with time. We also investigated the case for a specific choice of scale factor; namely, a(t=(t-t0β/(1-α. For this choice we have observed that a transition from quintessence to phantom is possible for the equation of state parameter. However, the ΛCDM phase is not attainable by the state-finder trajectories for this choice. Finally it has been observed that in both of the cases the generalized second law of thermodynamics is valid for the viscous EHRDE dominated universe enveloped by the apparent horizon.
Directory of Open Access Journals (Sweden)
Wilfried B. Krätzig
2014-01-01
Full Text Available This paper applies recent research on structural damage description to earthquake-resistant design concepts. Based on the primary design aim of life safety, this work adopts the necessity of additional protection aims for property, installation, and equipment. This requires the definition of damage indicators, which are able to quantify the arising structural damage. As in present design, it applies nonlinear quasistatic (pushover concepts due to code provisions as simplified dynamic design tools. Substituting so nonlinear time-history analyses, seismic low-cycle fatigue of RC structures is approximated in similar manner. The treatment will be embedded into a finite element environment, and the tangential stiffness matrix KT in tangential subspaces then is identified as the most general entry for structural damage information. Its spectra of eigenvalues λi or natural frequencies ωi of the structure serve to derive damage indicators Di, applicable to quasistatic evaluation of seismic damage. Because det KT=0 denotes structural failure, such damage indicators range from virgin situation Di=0 to failure Di=1 and thus correspond with Fema proposals on performance-based seismic design. Finally, the developed concept is checked by reanalyses of two experimentally investigated RC frames.
Directory of Open Access Journals (Sweden)
Vadim Ravara Viviani
2016-05-01
Full Text Available During photosynthesis, the photochemical electron transfer process is easily demonstrated by the Hill reaction, where artificial electron acceptors are reduced by active chloroplasts suspensions in the presence of light. However, the destiny of luminous energy absorbed by chlorophyll molecules in uncoupled or damaged photosystems is not usually demonstrated. Here we provide an adaptation of the classical Hill reaction using intact spinach chloroplasts, which includes the visualization of energy dissipation by fluorescence in lysed chloroplasts, and a dose/effect response in photosystems inhibited by the herbicide DCMU. This laboratory lesson, which is aimed to biochemistry and biophysics for undergraduate courses of Chemistry, Biological, Environmental and Agricultural Sciences, provides the basic photochemical principles using the classical Hill reaction, and photophysical principles through the visualization of energy dissipation by chlorophyll fluorescence, improving the understanding of the photosynthetic process, and introducing the concept of fluorescence and its applications as bioanalytical tool to monitor photosynthesis in plants and vegetal ecosystems.
Impact of Energy Losses Due to Failures on Photovoltaic Plant Energy Balance
Directory of Open Access Journals (Sweden)
Isidoro Lillo-Bravo
2018-02-01
Full Text Available Photovoltaic (PV plant failures have a significant influence on PV plant security, reliability, and energy balance. Energy losses produced by a PV plant are due to two large causes: failures and inefficiencies. Knowing the relative influence of energy losses due to failures and energy losses due to inefficiencies on the PV plant energy balance contribute to the optimization of its design, commissioning, and maintenance tasks. This paper estimates the failure rates, grouped by components, and the relative impact of the failures on the PV plant energy balance through real operation and maintenance follow-up data of 15 PV plants in Spain and Italy for 15 months. Results show that the influence of failures in energy losses of all analysed PV plants is low, reaching a maximum value of 0.96% of the net energy yield. Solar field energy losses only represent 4.26% of all failure energy losses. On the other hand, energy losses due to inefficiencies have represented between 22.34% and 27.58% of the net energy yield.
The super-excess energy dissipation in diatom algae: comparative analysis with higher plants.
Ruban, Alexander; Lavaud, Johann; Rousseau, Bernard; Guglielmi, Gerard; Horton, Peter; Etienne, Anne-Lise
2004-01-01
When grown at intermittent light regime, diatom alga Phaeodactylum tricornutum is able to form photoprotective non-photochemical chlorophyll fluorescence quenching (NPQ) three to five times larger than that observed in the higher plants. This quenching is sustained in the dark for 5 to 10 min, reverses completely within approximately 1 h and seems to be very tightly related to the presence of the zeaxanthin analogue, diatoxanthin. Addition of the uncoupler NH4Cl before illumination can completely abolish formation of NPQ, revealing the DeltapH-dependency of the xanthophyll cycle activity. Once established, NPQ can also be almost completely reversed by the uncoupler. However, the higher NPQ is formed the more time is required for its reversal. At the point when the fluorescence was approximately 90% recovered the level of illumination-induced diatoxanthin was found to be only partially reduced. This indicates that the proton gradient is a key triggering factor of NPQ. It was also noticed that NPQ in Phaeodactylum cells was absent even when majority of reaction centers were closed and the plastoquinone pool was significantly reduced. The absence of NPQ at these conditions could be due to very low levels of DeltapH. It is likely that in diatoms alternative sources of protons such as the PS I cyclic electron transfer and/or chlororespiration are important in generating the proton gradient sufficient to trigger NPQ. Absorption changes associated with the xanthophyll cycle activity were found to be larger than those for higher plants. The position of the positive maximum in the difference spectrum illuminated-minus-dark was 512-514 nm in comparison to the 505-508 nm for leaves. The 535 nm band associated with NPQ in plants is absent in Phaeodactylum. An uncoupler-sensitive absorption change at 522 nm was discovered. Kinetics of NPQ showed linear correlation with the 522 nm absorption change.
Cating, Emma E M; Pinion, Christopher W; Van Goethem, Erika M; Gabriel, Michelle M; Cahoon, James F; Papanikolas, John M
2016-01-13
Thermal management is an important consideration for most nanoelectronic devices, and an understanding of the thermal conductivity of individual device components is critical for the design of thermally efficient systems. However, it can be difficult to directly probe local changes in thermal conductivity within a nanoscale system. Here, we utilize the time-resolved and diffraction-limited imaging capabilities of ultrafast pump-probe microscopy to determine, in a contact-free configuration, the local thermal conductivity in individual Si nanowires (NWs). By suspending single NWs across microfabricated trenches in a quartz substrate, the properties of the same NW both on and off the substrate are directly compared. We find the substrate has no effect on the recombination lifetime or diffusion length of photogenerated charge carriers; however, it significantly impacts the thermal relaxation properties of the NW. In substrate-supported regions, thermal energy deposited into the lattice by the ultrafast laser pulse dissipates within ∼10 ns through thermal diffusion and coupling to the substrate. In suspended regions, the thermal energy persists for over 100 ns, and we directly image the time-resolved spatial motion of the thermal signal. Quantitative analysis of the transient images permits direct determination of the NW's local thermal conductivity, which we find to be a factor of ∼4 smaller than in bulk Si. Our results point to the strong potential of pump-probe microscopy to be used as an all-optical method to quantify the effects of localized environment and morphology on the thermal transport characteristics of individual nanostructured components.
Directory of Open Access Journals (Sweden)
Yi-Ning Zhang
2017-02-01
Full Text Available Response Surface Methodology (RSM is introduced to optimize the control rod positions in a pressurized water reactor (PWR core. The widely used 3D-IAEA benchmark problem is selected as the typical PWR core and the neutron flux field is solved. Besides, some additional thermal parameters are assumed to obtain the temperature distribution. Then the total and local entropy production is calculated to evaluate the energy dissipation. Using RSM, three directions of optimization are taken, which aim to determine the minimum of power peak factor Pmax, peak temperature Tmax and total entropy production Stot. These parameters reflect the safety and energy dissipation in the core. Finally, an optimization scheme was obtained, which reduced Pmax, Tmax and Stot by 23%, 8.7% and 16%, respectively. The optimization results are satisfactory.
Ruban, Alexander V; Belgio, Erica
2014-04-19
The principle of quantifying the efficiency of protection of photosystem II (PSII) reaction centres against photoinhibition by non-photochemical energy dissipation (NPQ) has been recently introduced by Ruban & Murchie (2012 Biochim. Biophys. Acta 1817, 977-982 (doi:10.1016/j.bbabio.2012.03.026)). This is based upon the assessment of two key parameters: (i) the relationship between the PSII yield and NPQ, and (ii) the fraction of intact PSII reaction centres in the dark after illumination. In this paper, we have quantified the relationship between the amplitude of NPQ and the light intensity at which all PSII reaction centres remain intact for plants with different levels of PsbS protein, known to play a key role in the process. It was found that the same, nearly linear, relationship exists between the levels of the protective NPQ component (pNPQ) and the tolerated light intensity in all types of studied plants. This approach allowed for the quantification of the maximum tolerated light intensity, the light intensity at which all plant leaves become photoinhibited, the fraction of (most likely) unnecessary or 'wasteful' NPQ, and the fraction of photoinhibited PSII reaction centres under conditions of prolonged illumination by full sunlight. It was concluded that the governing factors in the photoprotection of PSII are the level and rate of protective pNPQ formation, which are often in discord with the amplitude of the conventional measure of photoprotection, the quickly reversible NPQ component, qE. Hence, we recommend pNPQ as a more informative and less ambiguous parameter than qE, as it reflects the effectiveness and limitations of the major photoprotective process of the photosynthetic membrane.
Directory of Open Access Journals (Sweden)
Q Joyce Han
Full Text Available Right ventricular (RV function has increasingly being recognized as an important predictor for morbidity and mortality in patients with pulmonary arterial hypertension (PAH. The increased RV after-load increase RV work in PAH. We used time-resolved 3D phase contrast MRI (4D flow MRI to derive RV kinetic energy (KE work density and energy loss in the pulmonary artery (PA to better characterize RV work in PAH patients.4D flow and standard cardiac cine images were obtained in ten functional class I/II patients with PAH and nine healthy subjects. For each individual, we calculated the RV KE work density and the amount of viscous dissipation in the PA.PAH patients had alterations in flow patterns in both the RV and the PA compared to healthy subjects. PAH subjects had significantly higher RV KE work density than healthy subjects (94.7±33.7 mJ/mL vs. 61.7±14.8 mJ/mL, p = 0.007 as well as a much greater percent PA energy loss (21.1±6.4% vs. 2.2±1.3%, p = 0.0001 throughout the cardiac cycle. RV KE work density and percent PA energy loss had mild and moderate correlations with RV ejection fraction.This study has quantified two kinetic energy metrics to assess RV function using 4D flow. RV KE work density and PA viscous energy loss not only distinguished healthy subjects from patients, but also provided distinction amongst PAH patients. These metrics hold promise as imaging markers for RV function.
Han, Q Joyce; Witschey, Walter R T; Fang-Yen, Christopher M; Arkles, Jeffrey S; Barker, Alex J; Forfia, Paul R; Han, Yuchi
2015-01-01
Right ventricular (RV) function has increasingly being recognized as an important predictor for morbidity and mortality in patients with pulmonary arterial hypertension (PAH). The increased RV after-load increase RV work in PAH. We used time-resolved 3D phase contrast MRI (4D flow MRI) to derive RV kinetic energy (KE) work density and energy loss in the pulmonary artery (PA) to better characterize RV work in PAH patients. 4D flow and standard cardiac cine images were obtained in ten functional class I/II patients with PAH and nine healthy subjects. For each individual, we calculated the RV KE work density and the amount of viscous dissipation in the PA. PAH patients had alterations in flow patterns in both the RV and the PA compared to healthy subjects. PAH subjects had significantly higher RV KE work density than healthy subjects (94.7±33.7 mJ/mL vs. 61.7±14.8 mJ/mL, p = 0.007) as well as a much greater percent PA energy loss (21.1±6.4% vs. 2.2±1.3%, p = 0.0001) throughout the cardiac cycle. RV KE work density and percent PA energy loss had mild and moderate correlations with RV ejection fraction. This study has quantified two kinetic energy metrics to assess RV function using 4D flow. RV KE work density and PA viscous energy loss not only distinguished healthy subjects from patients, but also provided distinction amongst PAH patients. These metrics hold promise as imaging markers for RV function.
Shon, Sudeok; Yoo, Mina; Lee, Seungjae
2017-03-06
The steel frame reinforced with steel shear wall is a lateral load resisting system and has higher strength and shear performance than the concrete shear wall system. Especially, using corrugated steel plates in these shear wall systems improves out-of-plane stiffness and flexibility in the deformation along the corrugation. In this paper, a cyclic loading test of this steel frame reinforced with trapezoidal-corrugated steel plate was performed to evaluate the structural performance. The hysteresis behavior and the energy dissipation capacity of the steel frame were also compared according to the corrugated direction of the plate. For the test, one simple frame model without the wall and two frame models reinforced with the plate are considered and designed. The test results showed that the model reinforced with the corrugated steel plate had a greater accumulated energy dissipation capacity than the experimental result of the non-reinforced model. Furthermore, the energy dissipation curves of two reinforced frame models, which have different corrugated directions, produced similar results.
Dissipation regimes for short wind waves
Caulliez, Guillemette
2013-02-01
The dissipation processes affecting short wind waves of centimeter and decimeter scales are investigated experimentally in laboratory. The processes include damping due to molecular viscosity, generation of capillary waves, microbreaking, and breaking. The observations were made in a large wind wave tank for a wide range of fetches and winds, using a laser sheet and a high-resolution video camera. The work aims at constructing a comprehensive picture of dissipative processes in the short wind wave field, to find for which scales particular dissipative mechanism may become important. Four distinct regimes have been identified. For capillary-gravity wave fields, i.e., for dominant waves with scales below 4 cm, viscous damping is found to be the main dissipation mechanism. The gravity-capillary wave fields with dominant wavelength less than 10 cm usually exhibit a train of capillary ripples at the crest wavefront, but no wave breaking. For such waves, the main dissipation process is molecular viscosity occurring through nonlinear energy cascade toward high-frequency motions. Microscale breaking takes place for waves longer than 10 cm and manifests itself in a very localized surface disruption on the forward face of the crest. Such events generate turbulent motions in water and thus enhance wave dissipation. Plunging breaking, characterized by formation of a crest bulge, a microjet hitting the water surface and a splash-up, occurs for short gravity waves of wavelength exceeding 20 cm. Macroscale spilling breaking is also observed for longer waves at high winds. In both cases, the direct momentum transfer from breaking waves to the water flow contributes significantly to wave damping.
Demmig, B; Winter, K; Krüger, A; Czygan, F C
1988-05-01
Upon termination of watering of plants of Nerium oleander exposed to high light, photochemical efficiency became reduced as leaf water content decreased. Evidence is presented that this type of photoinhibition reflects to a substantial degree radiationless dissipation of excitation energy, probably mediated by the carotenoid zeaxanthin. During the imposition of water stress, the zeaxanthin content of leaves increased at the expense of violaxanthin and beta-carotene as a water deficit developed over a period of several days. The increase in zeaxanthin content was linearly related to an increase in the rate of radiationless energy dissipation in the antenna chlorophyll as calculated from the characteristics of chlorophyll a fluorescence measured with a pulse amplitude modulated fluorometer at room temperature. The increase in the rate of radiationless dissipation was also linearly related to a decrease in PSII photochemical efficiency as indicated by the ratio of variable to maximum fluorescence. Leaves of well-watered shade plants of N. oleander exposed to strong light showed a similar increase in zeaxanthin content as sun leaves of the same species subjected to drought in strong light. Shade leaves possessed the same capacity as sun leaves to form zeaxanthin at the expense of both violaxanthin and beta-carotene. The resistance of this species to the destructive effects of excess light appears to be related to interconversions between beta-carotene and the three carotenoids of the xanthophyll cycle.
Nanoscale thermal imaging of dissipation in quantum systems.
Halbertal, D; Cuppens, J; Shalom, M Ben; Embon, L; Shadmi, N; Anahory, Y; Naren, H R; Sarkar, J; Uri, A; Ronen, Y; Myasoedov, Y; Levitov, L S; Joselevich, E; Geim, A K; Zeldov, E
2016-11-17
Energy dissipation is a fundamental process governing the dynamics of physical, chemical and biological systems. It is also one of the main characteristics that distinguish quantum from classical phenomena. In particular, in condensed matter physics, scattering mechanisms, loss of quantum information or breakdown of topological protection are deeply rooted in the intricate details of how and where the dissipation occurs. Yet the microscopic behaviour of a system is usually not formulated in terms of dissipation because energy dissipation is not a readily measurable quantity on the micrometre scale. Although nanoscale thermometry has gained much recent interest, existing thermal imaging methods are not sensitive enough for the study of quantum systems and are also unsuitable for the low-temperature operation that is required. Here we report a nano-thermometer based on a superconducting quantum interference device with a diameter of less than 50 nanometres that resides at the apex of a sharp pipette: it provides scanning cryogenic thermal sensing that is four orders of magnitude more sensitive than previous devices-below 1 μK Hz -1/2 . This non-contact, non-invasive thermometry allows thermal imaging of very low intensity, nanoscale energy dissipation down to the fundamental Landauer limit of 40 femtowatts for continuous readout of a single qubit at one gigahertz at 4.2 kelvin. These advances enable the observation of changes in dissipation due to single-electron charging of individual quantum dots in carbon nanotubes. They also reveal a dissipation mechanism attributable to resonant localized states in graphene encapsulated within hexagonal boron nitride, opening the door to direct thermal imaging of nanoscale dissipation processes in quantum matter.
Early dissipation and viscosity
Bozek, Piotr
2008-01-01
We consider dissipative phenomena due to the relaxation of an initial anisotropic local pressure in the fireball created in relativistic heavy-ion collisions, both for the Bjorken boost-invariant case and for the azimuthally symmetric radial expansion with boost-invariance. The resulting increase of the entropy can be counterbalanced by a suitable retuning of the initial temperature. An increase of the transverse collective flow is observed. The influence of the shear viscosity on the longitu...
Johnson, Matthew P.; Ruban, Alexander V.
2009-01-01
Non-photochemical quenching (NPQ), a mechanism of energy dissipation in higher plants protects photosystem II (PSII) reaction centers from damage by excess light. NPQ involves a reduction in the chlorophyll excited state lifetime in the PSII harvesting antenna (LHCII) by a quencher. Yet, little is known about the effect of the quencher on chlorophyll excited state energy and dynamics. Application of picosecond time-resolved fluorescence spectroscopy demonstrated that NPQ involves a red-shift (60 ± 5 cm−1) and slight enhancement of the vibronic satellite of the main PSII lifetime component present in intact chloroplasts. Whereas this fluorescence red-shift was enhanced by the presence of zeaxanthin, it was not dependent upon it. The red-shifted fluorescence of intact chloroplasts in the NPQ state was accompanied by red-shifted chlorophyll a absorption. Nearly identical absorption and fluorescence changes were observed in isolated LHCII complexes quenched in a low detergent media, suggesting that the mechanism of quenching is the same in both systems. In both cases, the extent of the fluorescence red-shift was shown to correlate with the lifetime of a component. The alteration in the energy of the emitting chlorophyll(s) in intact chloroplasts and isolated LHCII was also accompanied by changes in lutein 1 observed in their 77K fluorescence excitation spectra. We suggest that the characteristic red-shifted fluorescence emission reflects an altered environment of the emitting chlorophyll(s) in LHCII brought about by their closer interaction with lutein 1 in the quenching locus. PMID:19567871
Avery, Katherine R.
Isothermal low cycle fatigue (LCF) and anisothermal thermomechanical fatigue (TMF) tests were conducted on a high silicon molybdenum (HiSiMo) cast iron for temperatures up to 1073K. LCF and out-of-phase (OP) TMF lives were significantly reduced when the temperature was near 673K due to an embrittlement phenomenon which decreases the ductility of HiSiMo at this temperature. In this case, intergranular fracture was predominant, and magnesium was observed at the fracture surface. When the thermal cycle did not include 673K, the failure mode was predominantly transgranular, and magnesium was not present on the fracture surface. The in-phase (IP) TMF lives were unaffected when the thermal cycle included 673K, and the predominant failure mode was found to be transgranular fracture, regardless of the temperature. No magnesium was present on the IP TMF fracture surfaces. Thus, the embrittlement phenomenon was found to contribute to fatigue damage only when the temperature was near 673K and a tensile stress was present. To account for the temperature- and stress-dependence of the embrittlement phenomenon on the TMF life of HiSiMo cast iron, an original model based on the cyclic inelastic energy dissipation is proposed which accounts for temperature-dependent differences in the rate of fatigue damage accumulation in tension and compression. The proposed model has few empirical parameters. Despite the simplicity of the model, the predicted fatigue life shows good agreement with more than 130 uniaxial low cycle and thermomechanical fatigue tests, cyclic creep tests, and tests conducted at slow strain rates and with hold times. The proposed model was implemented in a multiaxial formulation and applied to the fatigue life prediction of an exhaust manifold subjected to severe thermal cycles. The simulation results show good agreement with the failure locations and number of cycles to failure observed in a component-level experiment.
Energy Technology Data Exchange (ETDEWEB)
Logan, B.A.; Combs, A.; Kent, R.; Stanley, L. [Bowdoin College, Brunswick, ME (United States). Dept. of Biology; Myers, K. [Texas Tech Univ., Lubbock, TX (United States). Dept. of Biological Sciences; Tissue, D.T. [Texas Tech Univ., Lubbock, TX (United States). Dept. of Biological Sciences; Western Sydney Univ., Richmond, NSW (Australia). Centre for Plant and Food Science
2009-06-15
This study investigated the biological adaptation of loblolly pine following long-term seasonal exposure to elevated carbon dioxide (CO{sub 2}) partial pressures (pCO{sub 2}). Exposure to elevated atmospheric CO{sub 2} (pCO{sub 2}) usually results in significant stimulation in light-saturated rates of photosynthetic CO{sub 2} assimilation. Plants are protected against photoinhibition by biochemical processes known as photoprotection, including energy dissipation, which converts excess absorbed light energy into heat. This study was conducted in the eighth year of exposure to elevated pCO{sub 2} at the Duke FACE site. The effect of elevated pCO{sub 2} on electron transport and energy dissipation in the pine trees was examined by coupling the analyses of the capacity for photosynthetic oxygen (O{sub 2}) evolution, chlorophyll fluorescence emission and photosynthetic pigment composition with measurements of net photosynthetic CO{sub 2} assimilation (Asat). During the summer growing season, Asat was 50 per cent higher in current-year needles and 24 per cent higher in year-old needles in elevated pCO{sub 2} in comparison with needles of the same age cohort in ambient pCO{sub 2}. Thus, older needles exhibited greater photosynthetic down-regulation than younger needles in elevated pCO{sub 2}. In the winter, Asat was not significantly affected by growth pCO{sub 2}. Asat was lower in winter than in summer. Growth at elevated pCO{sub 2} had no significant effect on the capacity for photosynthetic oxygen evolution, photosystem 2 efficiencies, chlorophyll content or the size and conversion state of the xanthophyll cycle, regardless of season or needle age. There was no evidence that photosynthetic electron transport or photoprotective energy dissipation responded to compensate for the effects of elevated pCO{sub 2} on Calvin cycle activity. 73 refs., 4 figs.
International Nuclear Information System (INIS)
Logan, B.A.; Combs, A.; Kent, R.; Stanley, L.; Myers, K.; Tissue, D.T.; Western Sydney Univ., Richmond, NSW
2009-01-01
This study investigated the biological adaptation of loblolly pine following long-term seasonal exposure to elevated carbon dioxide (CO 2 ) partial pressures (pCO 2 ). Exposure to elevated atmospheric CO 2 (pCO 2 ) usually results in significant stimulation in light-saturated rates of photosynthetic CO 2 assimilation. Plants are protected against photoinhibition by biochemical processes known as photoprotection, including energy dissipation, which converts excess absorbed light energy into heat. This study was conducted in the eighth year of exposure to elevated pCO 2 at the Duke FACE site. The effect of elevated pCO 2 on electron transport and energy dissipation in the pine trees was examined by coupling the analyses of the capacity for photosynthetic oxygen (O 2 ) evolution, chlorophyll fluorescence emission and photosynthetic pigment composition with measurements of net photosynthetic CO 2 assimilation (Asat). During the summer growing season, Asat was 50 per cent higher in current-year needles and 24 per cent higher in year-old needles in elevated pCO 2 in comparison with needles of the same age cohort in ambient pCO 2 . Thus, older needles exhibited greater photosynthetic down-regulation than younger needles in elevated pCO 2 . In the winter, Asat was not significantly affected by growth pCO 2 . Asat was lower in winter than in summer. Growth at elevated pCO 2 had no significant effect on the capacity for photosynthetic oxygen evolution, photosystem 2 efficiencies, chlorophyll content or the size and conversion state of the xanthophyll cycle, regardless of season or needle age. There was no evidence that photosynthetic electron transport or photoprotective energy dissipation responded to compensate for the effects of elevated pCO 2 on Calvin cycle activity. 73 refs., 4 figs
Systems with small dissipation
Braginsky, V B; Panov, V I
1985-01-01
Introduction ; mechanical oscillators with small dissipation ; electromagnetic resonators with small dissipation ; high-quality electromagnetic resonators in physical experiments ; mechanical oscillators in physical experiments
Energy Technology Data Exchange (ETDEWEB)
Metivier, V. [Caen Univ., 14 (France). Lab. de Physique Corpusculaire
1995-04-01
This work is about the first experimental results obtained with the INDRA multidetector. First, the characterization of reaction mechanisms is performed. For complete events, global description of the collision is performed and compared with theoretical calculations. Dissipative binary mechanisms represent the largest part of the cross section for violent collisions whatever the bombarding energy (from 25 to 74 MeV/u) for the studied systems (Ar + KCl and Xe + Sn). The two outgoing products decay takes place through light charged particle and fragment emission. The reconstruction of the two primary sources is achieved, allowing thus the study of the evolution of the energy dissipation. Excitation energies exceeding 10 MeV/u are reached. The decay of the primary outgoing partners can be understood in a statistical model approach and the role of collective modes like expansion energy seems to be negligible. The study of the angular distributions points out angular momentum effects, `proximity effect` and a dynamical ternary process corresponding to the emission of a light fragment in between the two heavier products. For the most violent collisions, events can also be interpreted in terms of the multifragmentation of a single source, at least for the Xe + Sn system at 50 MeV/u (80 m barn). For the lower incident energies, fusion residues associated to the largest dissipations are recognized, but the cross sections is small (35 m barn for the Ar + KCl system at 32 MeV/u). (author) 91 refs.
Directory of Open Access Journals (Sweden)
Mahmoud Bayat
Full Text Available The behavior of braced steel frame structures is of special importance due to its extensive use. Also the application of active and semi-active control systems, regarding to their benefits in obtaining better seismic performance has increased significantly. The majority of the works on steel structures and steel connections has been done under far field records, and the behavior of steel frame structures equipped with yielding dampers under these circumstances has not yet been fully analyzed. The main purpose of this paper is to determine the behavior of structures equipped with yielding dampers, located in near field based on energy concepts. In order to optimize their seismic behavior, the codes and solutions are also presented.The selected system is a braced steel frame system which is equipped with yielding dampers and the analysis is performed using the "Perform 3D V.4" software and the conclusions are drawn upon energy criterion. The effect of PGA variation and height of the frames are also considered in the study .Finally, using the above mentioned results, a proper solution is presented for typical systems in order to increase the energy damping ability and reduce the destructive effects in structures on an earthquake event, so that a great amount of induced energy is damped and destruction of the structure is prevented as much as possible.
Dissipative structures in magnetorotational turbulence
Ross, Johnathan; Latter, Henrik N.
2018-03-01
Via the process of accretion, magnetorotational turbulence removes energy from a disk's orbital motion and transforms it into heat. Turbulent heating is far from uniform and is usually concentrated in small regions of intense dissipation, characterised by abrupt magnetic reconnection and higher temperatures. These regions are of interest because they might generate non-thermal emission, in the form of flares and energetic particles, or thermally process solids in protoplanetary disks. Moreover, the nature of the dissipation bears on the fundamental dynamics of the magnetorotational instability (MRI) itself: local simulations indicate that the large-scale properties of the turbulence (e.g. saturation levels, the stress-pressure relationship) depend on the short dissipative scales. In this paper we undertake a numerical study of how the MRI dissipates and the small-scale dissipative structures it employs to do so. We use the Godunov code RAMSES and unstratified compressible shearing boxes. Our simulations reveal that dissipation is concentrated in ribbons of strong magnetic reconnection that are significantly elongated in azimuth, up to a scale height. Dissipative structures are hence meso-scale objects, and potentially provide a route by which large scales and small scales interact. We go on to show how these ribbons evolve over time — forming, merging, breaking apart, and disappearing. Finally, we reveal important couplings between the large-scale density waves generated by the MRI and the small-scale structures, which may illuminate the stress-pressure relationship in MRI turbulence.
Wang, Furui; Huo, Linsheng; Song, Gangbing
2018-01-01
Monitoring of bolt looseness is essential for ensuring the safety and reliability of equipment and structures with bolted connections. It is well known that tangential damping has an important influence on energy dissipation during wave propagation across the bolted joints, which require different levels of preload. In this paper, the energy dissipation generated by tangential damping of the bolted joints under different bolt preloads was modeled analytically based on fractal contact theory, which took the imperfect interface into account. A saturation value exists with the increase of the bolt preload, and the center frequency of emitted signal is demonstrated to affect the received energy significantly. Compared with previous similar studies based on experimental techniques and numerical method, the investigation presented in this paper explains the phenomenon from the inherent mechanism, and achieves the accurate quantitative monitoring of bolt looseness directly, rather than an indirect failure index. Finally, the validity of the proposed method in this paper was demonstrated with an experimental study of a bolted joint with different preload levels.
Lian, Jijian; Wang, Xiaoqun; Zhang, Wenjiao; Ma, Bin; Liu, Dongming
2017-11-30
As excess water is discharged from a high dam, low frequency noise (air pulsation lower than 10 Hz, LFN) is generated and propagated in the surrounding areas, causing environmental hazards such as the vibration of windows and doors and the discomfort of local residents. To study the generation mechanisms and key influencing factors of LFN induced by flood discharge and energy dissipation from a high dam with a ski-jump type spillway, detailed prototype observations and analyses of LFN are carried out. The discharge flow field is simulated and analyzed using a gas-liquid turbulent flow model. The acoustic response characteristics of the air cavity, which is formed between the discharge nappe and dam body, are analyzed using an acoustic numerical model. The multi-sources generation mechanisms are first proposed basing on the prototype observation results, vortex sound model, turbulent flow model and acoustic numerical model. Two kinds of sources of LFN are studied. One comes from the energy dissipation of submerged jets in the plunge pool, the other comes from nappe-cavity coupled vibration. The results of the analyses reveal that the submerged jets in the plunge pool only contribute to an on-site LFN energy of 0-1.0 Hz, and the strong shear layers around the high-velocity submerged jets and wall jet development areas are the main acoustic source regions of LFN in the plunge pool. In addition, the nappe-cavity coupled vibration, which is induced when the discharge nappe vibrates with close frequency to the model frequency of the cavity, can induce on-site LFN energy with wider frequency spectrum energy within 0-4.0 Hz. By contrast, the contribution degrees to LFN energy from two acoustic sources are almost same, while the contribution degree from nappe-cavity coupled vibration is slightly higher.
Tobaruela, Almudena; Rojo, Francisco Javier; García Paez, José María; Bourges, Jean Yves; Herrero, Eduardo Jorge; Millán, Isabel; Alvarez, Lourdes; Cordon, Ángeles; Guinea, Gustavo V
2016-08-01
The aim of this study was to evaluate the variation of hardness with fatigue in calf pericardium, a biomaterial commonly used in bioprosthetic heart valves, and its relationship with the energy dissipated during the first fatigue cycle that has been shown to be a predictor of fatigue-life (García Páez et al., 2006, 2007; Rojo et al., 2010). Fatigue tests were performed in vitro on 24 pericardium specimens cut in a root-to-apex direction. The specimens were subjected to a maximum stress of 1MPa in blocks of 10, 25, 50, 100, 250, 500, 1000 and 1500 cycles. By means of a modified Shore A hardness test procedure, the hardness of the specimen was measured before and after fatigue tests. Results showed a significant correlation of such hardness with fatigue performance and with the energy dissipated in the first cycle of fatigue, a predictor of pericardium durability. The study showed indentation hardness as a simple and reliable indicator of mechanical performance, one which could be easily implemented in improving tissue selection. Copyright © 2016 Elsevier Ltd. All rights reserved.
International Nuclear Information System (INIS)
Thielen, M; Schmitt, C N Z; Eckert, S; Speck, T; Seidel, R
2013-01-01
The mechanical properties of artificial foams are mainly determined by the choice of bulk materials and relative density. In natural foams, in contrast, variation to optimize properties is achieved by structural optimization rather than by conscious substitution of bulk materials. Pomelos (Citrus maxima) have a thick foam-like peel which is capable of dissipating considerable amounts of kinetic energy and thus this fruit represents an ideal role model for the development of biomimetic impact damping structures. This paper focuses on the analysis of the biomechanics of the pomelo peel and on its structure–function relationship. It deals with the determination of the onset strain of densification of this foam-like tissue and on how this property is influenced by the arrangement of vascular bundles. It was found here that the vascular bundles branch in a very regular manner—every 16.5% of the radial peel thickness—and that the surrounding peel tissue (pericarp) attains its exceptional thickness mainly by the expansion of existing interconnected cells causing an increasing volume of the intercellular space, rather than by cell division. These findings lead to the discussion of the pomelo peel as an inspiration for fibre-reinforced cast metallic foams with the capacity for excellent energy dissipation. (paper)
Lombardo, S.; Wu, E. Y.; Stathis, J. H.
2017-08-01
We report the data and a model showing that the energy loss experienced by the carriers flowing through breakdown spots is the primary cause of progressive breakdown spot growth. The experiments are performed in gate dielectrics of metal-oxide-semiconductor (MOS) devices subjected to accelerated high electric field constant voltage stress under inversion conditions. The model is analytical and contains few free parameters of clear physical meaning. This is compared to a large set of data on breakdown transients at various oxide thicknesses, stress voltages, and temperatures, both in cases of n-channel and p-channel transistors and polycrystalline Si/oxynitride/Si and metal gate/high k dielectric/Si gate stacks. The basic idea is that the breakdown transient is due to the growth of one or more filaments in the dielectric promoted by electromigration driven by the energy lost by the electrons traveling through the breakdown spots. Both cases of polycrystalline Si/oxynitride/Si and metal gate/high-k dielectric/Si MOS structures are investigated. The best fit values of the model to the data, reported and discussed in the paper, consistently describe a large set of data. The case of simultaneous growth of multiple progressive breakdown spots in the same device is also discussed in detail.
Energy and Economic Losses Due to Constant Power Outages in ...
African Journals Online (AJOL)
This study assesses the economic implication of electricity self-generation in Nigeria. In this regard, energy and exergetic utilization efficiencies of 19 representative generators and gas turbines from Afam power station were assessed based on real data obtained through survey of companies, oral interview, individuals and ...
Generation of zonal flow in the Earth's dissipative ionospheric F-layer
International Nuclear Information System (INIS)
Kaladze, T.D.; Shad, M.; Tsamalashvili, L.V.
2011-01-01
Generation of zonal flow in the Earth's dissipative ionospheric F-layer is considered. Dissipation arises due to Pedersen conductivity acting as an inductive (magnetic) inhibition. It is shown that in contrast to previous investigations the zonal flow growth rate does not depend on small wave vector component of zonal flow mode, needs no instability condition and the spectral energy transferring (inverse cascade) process unconditionally takes place. -- Highlights: → Generation of zonal flow in the Earth's dissipative ionospheric F-layer is considered. → Dissipation arises due to Pedersen conductivity acting as inductive (magnetic) inhibition. → It is shown that such generation doesn't need any instability condition. → Energy transferring (inverse cascade) process takes place even for the small values of pumping intensity.
Storage functions for dissipative linear systems are quadratic state functions
Trentelman, Harry L.; Willems, Jan C.
1997-01-01
This paper deals with dissipative dynamical systems. Dissipative dynamical systems can be used as models for physical phenomena in which energy exchange with their environment plays a role. In a dissipative dynamical system, the book-keeping of energy is done via the supply rate and a storage
Quantum dissipation, scattering and tunneling
International Nuclear Information System (INIS)
Eleuterio, S.M.; Vilela Mendes, R.
1984-01-01
A quantization technique for dissipative systems is used to discuss one dimensional problems including tunneling with dissipation, capture in dissipative potential wells and quantum coherence. (orig.)
Quantum dissipation of a simple conservative system
International Nuclear Information System (INIS)
Ibeh, G. J.; Mshelia, E. D.
2014-01-01
A model of quantum dissipative system is presented. Here dissipation of energy is demonstrated as based on the coupling of a free translational motion of a centre of mass to a harmonic oscillator. The two-dimensional arrangement of two coupled particles of different masses is considered.
Dissipative Solitons that Cannot be Trapped
International Nuclear Information System (INIS)
Pardo, Rosa; Perez-Garcia, Victor M.
2006-01-01
We show that dissipative solitons in systems with high-order nonlinear dissipation cannot survive in the presence of trapping potentials of the rigid wall or asymptotically increasing type. Solitons in such systems can survive in the presence of a weak potential but only with energies out of the interval of existence of linear quantum mechanical stationary states
Chen, Xuemei; Fried, Eliot
2008-10-01
Lundgren's vortex model for the intermittent fine structure of high-Reynolds-number turbulence is applied to the Navier-Stokes alphabeta equations and specialized to the Navier-Stokes alpha equations. The Navier-Stokes alphabeta equations involve dispersive and dissipative length scales alpha and beta, respectively. Setting beta equal to alpha reduces the Navier-Stokes alphabeta equations to the Navier-Stokes alpha equations. For the Navier-Stokes alpha equations, the energy spectrum is found to obey Kolmogorov's -5/3 law in a range of wave numbers identical to that determined by Lundgren for the Navier-Stokes equations. For the Navier-Stokes alphabeta equations, Kolmogorov's -5/3 law is also recovered. However, granted that beta Navier-Stokes alphabeta equations may have the potential to resolve features smaller than those obtainable using the Navier-Stokes alpha equations.
Logan, Barry A; Combs, Andrew; Myers, Kalisa; Kent, Rose; Stanley, Lela; Tissue, David T
2009-06-01
To determine the effect of growth under elevated CO(2) partial pressures (pCO(2)) on photosynthetic electron transport and photoprotective energy dissipation, we examined light-saturated net photosynthetic CO(2) assimilation (A(sat)), the capacity for photosynthetic O(2) evolution, chlorophyll fluorescence emission and the pigment composition of upper-canopy loblolly pine needles in the eighth year of exposure to elevated pCO(2) (20 Pa above ambient) at the free-air CO(2) enrichment facility in the Duke Forest. During the summer growing season, A(sat) was 50% higher in current-year needles and 24% higher in year-old needles in elevated pCO(2) in comparison with needles of the same age cohort in ambient pCO(2). Thus, photosynthetic down-regulation at elevated pCO(2) was observed in the summer in year-old needles. In the winter, A(sat) was not significantly affected by growth pCO(2). Reductions in A(sat), the capacity for photosynthetic O(2) evolution and photosystem II (PSII) efficiency in the light-acclimated and fully-oxidized states were observed in the winter when compared to summer. Growth at elevated pCO(2) had no significant effect on the capacity for photosynthetic O(2) evolution, PSII efficiencies in the light-acclimated and fully-oxidized states, chlorophyll content or the size and conversion state of the xanthophyll cycle, regardless of season or needle age cohort. Therefore, we observed no evidence that photosynthetic electron transport or photoprotective energy dissipation responded to compensate for the effects of elevated pCO(2) on Calvin cycle activity.
Grabelnych, O I; Borovik, O A; Tauson, E L; Pobezhimova, T P; Katyshev, A I; Pavlovskaya, N S; Koroleva, N A; Lyubushkina, I V; Bashmakov, V Yu; Popov, V N; Borovskii, G B; Voinikov, V K
2014-06-01
Gene expression, protein synthesis, and activities of alternative oxidase (AOX), uncoupling proteins (UCP), adenine nucleotide translocator (ANT), and non-coupled NAD(P)H dehydrogenases (NDex, NDPex, and NDin) were studied in shoots of etiolated winter wheat (Triticum aestivum L.) seedlings after exposure to hardening low positive (2°C for 7 days) and freezing (-2°C for 2 days) temperatures. The cold hardening efficiently increased frost-resistance of the seedlings and decreased the generation of reactive oxygen species (ROS) during further cold shock. Functioning of mitochondrial energy-dissipating systems can represent a mechanism responsible for the decrease in ROS under these conditions. These systems are different in their response to the action of the hardening low positive and freezing temperatures. The functioning of the first system causes induction of AOX and UCP synthesis associated with an increase in electron transfer via AOX in the mitochondrial respiratory chain and also with an increase in the sensitivity of mitochondrial non-phosphorylating respiration to linoleic and palmitic acids. The increase in electron transfer via AOX upon exposure of seedlings to hardening freezing temperature is associated with retention of a high activity of NDex. It seems that NDex but not the NDPex and NDin can play an important role in maintaining the functional state of mitochondria in heterotrophic tissues of plants under the influence of freezing temperatures. The involvement of the mitochondrial energy-dissipating systems and their possible physiological role in the adaptation of winter crops to cold and frost are discussed.
Optimal bounds on dissipation in stress driven flow
Tang, W.; Caulfield, C. P.; Young, W. R.
2003-11-01
We calculate the optimal upper and lower bounds, subject to the assumption of streamwise invariance, on the long-time-averaged mechanical energy dissipation rate ɛ within the flow of an incompressible viscous fluid of constant kinematic viscosity ν and depth h that is driven by a constant stress τ, defining an appropriate Grashof number G=τ h^2/ν^2. We show that ɛ ≤ τ^2/ν, i.e. the dissipation is bounded above by the dissipation associated with the laminar solution u=τ z hat ^x/ν. By using the the variational background method, (due to Constantin, Doering, and Hopf) and numerical continuation, we also generate the best possible rigorous lower bounds on the dissipation for arbitrary Grashof numbers. As G arrow ∞, we show that the dissipation is bounded below by ɛm = O(τ^3/2/h), with a numerical coefficient that we identify explicitly. The associated bounding solution has thin boundary layers at the top and bottom of the fluid layer with a deep intermediate region of weak shear.
2014-05-01
Currently, transportation and energy sectors are developed, managed, and operated independently of : one another. Due to the non-renewable nature of fossil fuels, energy security has evolved into a : strategic goal for the United States. The transpor...
Energy Technology Data Exchange (ETDEWEB)
Back, B.B.; Blumenthal, D.J.; Davids, C.N. [and others
1995-08-01
In this experiment we tried to measure the evaporation residue cross section over a wide range of beam energies for the {sup 100}Mo + {sup 116}Cd reaction using the FMA. However, because of longer-than-estimated runs needed at each beam energy, and the difficulty of bending evaporation residues at the higher energies in the FMA, data were taken only at beam energies of E{sub beam} = 460, 490, and 521 MeV, which correspond to excitation energies of E{sub exc} = 62, 78, and 95 MeV, respectively. By comparing to results for the {sup 32}S + {sup 184}W reactions measured recently, we expect to demonstrate a strong entrance channel effect related to the hindrance of complete fusion in near-symmetric heavy systems (a fusion hindrance factor of the order 7-10 is expected on the basis of the Extra-Push Model). The data are being analyzed.
Shpigel, Netanel; Levi, Mikhael D; Sigalov, Sergey; Daikhin, Leonid; Aurbach, Doron
2018-01-16
Quartz crystal microbalance with dissipation monitoring (QCM-D) generates surface-acoustic waves in quartz crystal plates that can effectively probe the structure of films, particulate composite electrodes of complex geometry rigidly attached to quartz crystal surface on one side and contacting a gas or liquid phase on the other side. The output QCM-D characteristics consist of the resonance frequency (MHz frequency range) and resonance bandwidth measured with extra-ordinary precision of a few tenths of Hz. Depending on the electrodes stiffness/softness, QCM-D operates either as a gravimetric or complex mechanical probe of their intrinsic structure. For at least 20 years, QCM-D has been successfully used in biochemical and environmental science and technology for its ability to probe the structure of soft solvated interfaces. Practical battery and supercapacitor electrodes appear frequently as porous solids with their stiffness changing due to interactions with electrolyte solutions or as a result of ion intercalation/adsorption and long-term electrode cycling. Unfortunately, most QCM measurements with electrochemical systems are carried out based on a single (fundamental) frequency and, as such, provided that the resonance bandwidth remains constant, are suitable for only gravimetric sensing. The multiharmonic measurements have been carried out mainly on conducting/redox polymer films rather than on typical composite battery/supercapacitor electrodes. Here, we summarize the most recent publications devoted to the development of electrochemical QCM-D (EQCM-D)-based methodology for systematic characterization of mechanical properties of operating battery/supercapacitor electrodes. By varying the electrodes' composition and structure (thin/thick layers, small/large particles, binders with different mechanical properties, etc.), nature of the electrolyte solutions and charging/cycling conditions, the method is shown to be operated in different application modes. A
Minimum dissipative relaxed states in toroidal plasmas
Indian Academy of Sciences (India)
organised equi- librium in RFP and tokamak by a deterministic approach to incompressible dissipative magnetohydrodynamics. In an earlier work Kondoh [8] formulated an energy principle including the edge plasma effects for a slightly resistive MHD ...
A heat dissipating model for water cooling garments
Directory of Open Access Journals (Sweden)
Yang Kai
2013-01-01
Full Text Available A water cooling garment is a functional clothing used to dissipate human body’s redundant energy in extravehicular environment or other hot environment. Its heat dissipating property greatly affects body’s heat balance. In this paper, a heat dissipating model for the water cooling garment is established and verified experimentally using the experimental thermal-manikin.
A heat dissipating model for water cooling garments
Yang Kai; Jiao Ming-Li; Liu Zhe; Zhang Wei-Yuan
2013-01-01
A water cooling garment is a functional clothing used to dissipate human body’s redundant energy in extravehicular environment or other hot environment. Its heat dissipating property greatly affects body’s heat balance. In this paper, a heat dissipating model for the water cooling garment is established and verified experimentally using the experimental thermal-manikin.
Energy loss mechanism for suspended micro- and nanoresonators due to the Casimir force
Gusso, André
2011-01-01
A so far not considered energy loss mechanism in suspended micro- and nanoresonators due to noncontact acoustical energy loss is investigated theoretically. The mechanism consists on the conversion of the mechanical energy from the vibratory motion of the resonator into acoustic waves on large nearby structures, such as the substrate, due to the coupling between the resonator and those structures resulting from the Casimir force acting over the separation gaps. Analytical expressions for the ...
Directory of Open Access Journals (Sweden)
David Sabater
2016-08-01
Full Text Available Background. A “cafeteria” diet is a self-selected high-fat diet, providing an excess of energy, which can induce obesity. Excess of lipids in the diet hampers glucose utilization eliciting insulin resistance, which, further limits amino acid oxidation for energy. Methods. Male Wistar rats were exposed for a month to “cafeteria” diet. Rats were cannulated and fluorescent microspheres were used to determine blood flow. Results. Exposure to the cafeteria diet did not change cardiac output, but there was a marked shift in organ irrigation. Skin blood flow decreased to compensate increases in lungs and heart. Blood flow through adipose tissue tended to increase in relation to controls, but was considerably increased in brown adipose tissue (on a weight basis. Discussion. The results suggest that the cafeteria diet-induced changes were related to heat transfer and disposal.
Hazell, P. J.; Appleby-Thomas, G. J.
2009-01-01
The threat of fragmenting munitions from MANPADS to civilian and military aircraft has, in recent years, become an ever increasing worry. One of the ways to enhance the protection of CFRP-based composites is to add lightweight materials that can provide increased ballistic protection. In this study, several hybrid CFRP laminates of different material and geometrical configurations have been subjected to impact by a high velocity steel sphere with an impact energy of c.a. 440...
Energy Technology Data Exchange (ETDEWEB)
Funaki, T.; Hayashi, S. [Osaka University, Osaka (Japan). Faculty of engineering
1996-12-31
It is known in estimating vibration characteristics of a ship that fluid range affects largely a structure. In order to analyze the compound vibration therein, a method was proposed, which estimates vibration levels without using the finite element method. However, the problem of mode decay ratio has not been solved. Therefore, this paper first describes a method to introduce an equivalent linear decay matrix. The paper then mentions difference in the decay effects due to fluid viscosity in a shallow and deep water regions. Furthermore, vibration levels in the deep water region were estimated in a model experiment to verify the estimation result. Under a hypothesis that two-node vibration in a rotating ellipse has displacement distributions in the deep and shallow water regions equivalent, and when a case of vibration in a layer flow condition is calculated, dissipation energy in the shallow region is larger than that in the deep region by about 26%. About 5% of the total dissipation energy is consumed at bottom of the sea. According to a frequency response calculation, estimated values for the response levels still differ from experimental values, although the trend that the vibration levels change can be reproduced. 6 refs., 15 figs., 2 tabs.
Third sound dissipation at a point contact
International Nuclear Information System (INIS)
Ellis, F M; Eddinger, J D
2009-01-01
Third sound on a planar geometry at low temperatures is characterized by a rapidly diminishing thermal dissipation. Direct mechanical dissipation is limited to that associated with defects in the system. This includes interaction with pinned vortices, critical flow at surface defect sites, and unintentional acoustic coupling. Dissipation of this latter type is possible in the parallel plate geometry of capacitively detected third sound. We calculate the coupling of a third sound wave across a contacting bridge to a parallel plane, and investigate the energy transfer out of the wave and flow properties of the film in the vicinity of the contact. The presence of various mirror waves on the contacting plane is also considered. Experimental dissipation is observed in both geometries and it is shown that a single contact is capable of accounting for the dissipation as well as an unusually low observed critical velocity.
Dynamics of charged viscous dissipative cylindrical collapse with full causal approach
Energy Technology Data Exchange (ETDEWEB)
Shah, S.M.; Abbas, G. [The Islamia University of Bahawalpur, Department of Mathematics, Bahawalpur (Pakistan)
2017-11-15
The aim of this paper is to investigate the dynamical aspects of a charged viscous cylindrical source by using the Misner approach. To this end, we have considered the more general charged dissipative fluid enclosed by the cylindrical symmetric spacetime. The dissipative nature of the source is due to the presence of dissipative variables in the stress-energy tensor. The dynamical equations resulting from such charged cylindrical dissipative source have been coupled with the causal transport equations for heat flux, shear and bulk viscosity, in the context of the Israel-Steward theory. In this case, we have the considered Israel-Steward transportation equations without excluding the thermodynamics viscous/heat coupling coefficients. The results are compared with the previous works in which such coefficients were excluded and viscosity variables do not satisfy the casual transportation equations. (orig.)
Magnetic topology, nonequilibrium, and dissipation
International Nuclear Information System (INIS)
Parker, E.N.
1985-01-01
Static equilibrium of a magnetic field throughout a large volume of highly conducting fluid requires a degree of topological symmetry that is generally lacking in nature. The dynamical nonequilibrium of the magnetic topologies in the real world forms current sheets across which there is active reconnection of the field, dissipating the energy of the magnetic strains and reducing the fields toward simpler forms. The magnetic fields in astronomical settings are generally subject to continual straining by the convection within their parent body. The work done on the field by the convection appears in the energy of the small-scale strains, and is soon dissipated by the reconnection. The intense heating of the tenuous outer atmosphere of stars by this mechanism appears to be responsible for most of the X-ray emission of ordinary stars
Collisionless dissipation of Langmuir turbulence
International Nuclear Information System (INIS)
Erofeev, V.I.
2002-01-01
An analysis of two experimental observations of Langmuir wave collapse is performed. The corresponding experimental data are shown to give evidence against the collapse. The physical reason for preventing the collapses is found to be the nonresonant electron diffusion in momentums. In this process, plasma thermal electrons are efficiently heated at the expense of wave energy, and intense collisionless wave dissipation takes place. The basic reason of underestimation of this phenomenon in traditional theory is shown to be the substitution of real plasma by a plasma probabilistic ensemble. A theory of nonresonant electron diffusion in a single collisionless plasma is developed. It is shown that corresponding collisionless wave dissipation may arrest spectral energy transfer towards small wave numbers
Hussain, M Iftikhar; Reigosa, Manuel J
2011-11-01
This study investigated the effects of cinnamic acid (CA) on growth, biochemical and physiological responses of Lactuca sativa L. CA (0.1, 0.5, 1.0 and 1.5 mM) treatments decreased plant height, root length, leaf and root fresh weight, but it did not affect the leaf water status. CA treatment (1.5 mM) significantly reduced F(v), F(m), photochemical efficiency of PSII (F(v)/F(m)) and quantum yield of PSII (ΦPSII) photochemistry in L. sativa. The photochemical fluorescence quenching (qP) and non-photochemical quenching (NPQ) were reduced after treatment with 1.5 mM CA. Fraction of photon energy absorbed by PS II antennae trapped by "open" PS II reaction centers (P) was reduced by CA (1.5 mM) while, portion of absorbed photon energy thermally dissipated (D) and photon energy absorbed by PSII antennae and trapped by "closed" PSII reaction centers (E) was increased. Carbon isotope composition ratios (δ(13)C) was less negative (-27.10) in CA (1.5 mM) treated plants as compared to control (-27.61). Carbon isotope discrimination (Δ(13)C) and ratio of intercellular CO(2) concentration (ci/ca) from leaf to air were also less in CA treated plants. CA (1.5 mM) also decreased the leaf protein contents of L. sativa as compared to control. Copyright © 2011 Elsevier Masson SAS. All rights reserved.
Directory of Open Access Journals (Sweden)
Haoxiang He
2016-01-01
Full Text Available In view of the disadvantages such as higher yield stress and inadequate adjustability, a combined low yield point steel plate damper involving low yield point steel plates and common steel plates is proposed. Three types of combined plate dampers with new hollow shapes are proposed, and the specific forms include interior hollow, boundary hollow, and ellipse hollow. The “maximum stiffness” and “full stress state” are used as the optimization objectives, and the topology optimization of different hollow forms by alternating optimization method is to obtain the optimal shape. Various combined steel plate dampers are calculated by finite element simulation, the results indicate that the initial stiffness of the boundary optimized damper and interior optimized damper is lager, the hysteresis curves are full, and there is no stress concentration. These two types of optimization models made in different materials rations are studied by numerical simulation, and the adjustability of yield stress of these combined dampers is verified. The nonlinear dynamic responses, seismic capacity, and damping effect of steel frame structures with different combined dampers are analyzed. The results show that the boundary optimized damper has better energy-dissipation capacity and is suitable for engineering application.
Directory of Open Access Journals (Sweden)
N. Engler
2005-06-01
Full Text Available During the MIDAS/MaCWAVE campaign in summer 2002 we have observed turbulence using Doppler beam steering measurements obtained from the ALWIN VHF radar at Andøya/Northern Norway. This radar was operated in the Doppler beam steering mode for turbulence investigations during the campaign, as well as in spaced antenna mode, for continuously measuring the background wind field. The real-time data analysis of the Doppler radar backscattering provided the launch conditions for the sounding rockets. The spectral width data observed during the occurrence of PMSE were corrected for beam and shear broadening caused by the background wind field to obtain the turbulent part of the spectral width. The turbulent energy dissipation rates determined from the turbulent spectral width vary between 5 and 100mW kg^{-1} in the altitude range of 80-92km and increase with altitude. These estimations agree well with the in-situ measurements using the CONE sensor which was launched on 3 sounding rockets during the campaign.
Directory of Open Access Journals (Sweden)
N. Engler
2005-06-01
Full Text Available During the MIDAS/MaCWAVE campaign in summer 2002 we have observed turbulence using Doppler beam steering measurements obtained from the ALWIN VHF radar at Andøya/Northern Norway. This radar was operated in the Doppler beam steering mode for turbulence investigations during the campaign, as well as in spaced antenna mode, for continuously measuring the background wind field. The real-time data analysis of the Doppler radar backscattering provided the launch conditions for the sounding rockets. The spectral width data observed during the occurrence of PMSE were corrected for beam and shear broadening caused by the background wind field to obtain the turbulent part of the spectral width. The turbulent energy dissipation rates determined from the turbulent spectral width vary between 5 and 100mW kg-1 in the altitude range of 80-92km and increase with altitude. These estimations agree well with the in-situ measurements using the CONE sensor which was launched on 3 sounding rockets during the campaign.
Renewable Energy Potentials along the Bay of Bengal due to Tidal Water Level Variation
Directory of Open Access Journals (Sweden)
Ahmad Myisha
2018-01-01
Full Text Available The projected increase in energy demand coupled with concerns regarding present reliance on fossil fuel and associated environmental concerns had led to increased interest in exploiting renewable energy sources. Among different renewable energy sources, tidal energy is unique and most suitable because of its predictable nature and capability to ensure supply security. Tide consists of both kinetic and potential energy which can be converted to electricity using well-proven technology. The potential energy of tides - the principal focus of the study, is stored due to rise and fall of the sea level. Head difference created due to tidal variation between basin side and sea side of a barrage stores potential energy which is converted into fast-moving water that rotates turbine and generates electricity. Bangladesh with its long coastline has promising prospects of tidal energy resource development. The study focuses on tidal energy resource exploration and exploitation along several competent locations of the Bengal coastline. Tidal records of flood and ebb tide of these locations are analyzed to calculate the potential energy. Finally, available potential techniques of energy extraction are evaluated for annually generated energy estimation. This study investigates the prospect and utilization of tidal energy concept and reviews the possibilities and opportunities of employment of the technology for sustainable development and climate change mitigation in context of Bangladesh.
Directory of Open Access Journals (Sweden)
Lu-Ning Liu
Full Text Available BACKGROUND: Photosynthetic organisms have developed multiple protective mechanisms to prevent photodamage in vivo under high-light conditions. Cyanobacteria and red algae use phycobilisomes (PBsomes as their major light-harvesting antennae complexes. The orange carotenoid protein in some cyanobacteria has been demonstrated to play roles in the photoprotective mechanism. The PBsome-itself-related energy dissipation mechanism is still unclear. METHODOLOGY/PRINCIPAL FINDINGS: Here, single-molecule spectroscopy is applied for the first time on the PBsomes of red alga Porphyridium cruentum, to detect the fluorescence emissions of phycoerythrins (PE and PBsome core complex simultaneously, and the real-time detection could greatly characterize the fluorescence dynamics of individual PBsomes in response to intense light. CONCLUSIONS/SIGNIFICANCE: Our data revealed that strong green-light can induce the fluorescence decrease of PBsome, as well as the fluorescence increase of PE at the first stage of photobleaching. It strongly indicated an energetic decoupling occurring between PE and its neighbor. The fluorescence of PE was subsequently observed to be decreased, showing that PE was photobleached when energy transfer in the PBsomes was disrupted. In contrast, the energetic decoupling was not observed in either the PBsomes fixed with glutaraldehyde, or the mutant PBsomes lacking B-PE and remaining b-PE. It was concluded that the energetic decoupling of the PBsomes occurs at the specific association between B-PE and b-PE within the PBsome rod. Assuming that the same process occurs also at the much lower physiological light intensities, such a decoupling process is proposed to be a strategy corresponding to PBsomes to prevent photodamage of the photosynthetic reaction centers. Finally, a novel photoprotective role of gamma-subunit-containing PE in red algae was discussed.
The influence of an estimated energy saving due to natural ventilation on the Mexican energy system
DEFF Research Database (Denmark)
Oropeza-Perez, Ivan; Østergaard, Poul Alberg
2014-01-01
This article shows the impacts of the extensive use of NV (natural ventilation) in the Mexican residential sector on the Mexican energy system. By integrating a thermal-airflow simulation programme with an energy systems analysis model, the impact on the Mexican energy system of replacing air...... conditioning, in particular, with natural ventilation to cool residential buildings is determined. It is shown that when, as in Mexico, there is a relatively simple connection between supply and electricity demand, NV creates savings which could be used to reduce either the fossil-fuel-based generation...
Uncontrollable dissipative systems: observability and embeddability
Karikalan, Selvaraj; Belur, Madhu N.; Athalye, Chirayu D.; Razak, Rihab Abdul
2014-01-01
The theory of dissipativity is well developed for controllable systems. A more appropriate definition of dissipativity in the context of uncontrollable systems is in terms of the existence of a storage function, namely a function such that, along every system trajectory, its rate of change at each time instant is at most the power supplied to the system at that time. However, even when the supplied power is expressible in terms of just the external variables, the dissipativity property for uncontrollable systems crucially hinges on whether or not the storage function depends on variables unobservable/hidden from the external variables: this paper investigates the key aspects of both cases, and also proposes another intuitive definition of dissipativity. These three definitions are compared: we show that drawbacks of one definition are addressed by another. Dealing first with observable storage functions, under the conditions that no two uncontrollable poles add to zero and that dissipativity is strict as frequency tends to infinity, we prove that the dissipativities of a system and its controllable part are equivalent. We use the behavioural approach for formalising key notions: a system behaviour is the set of all system trajectories. We prove that storage functions have to be unobservable for 'lossless' uncontrollable systems. It is known, however, that unobservable storage functions result in certain 'fallacious' examples of lossless systems. We propose an intuitive definition of dissipativity: a system/behaviour is called dissipative if it can be embedded in a controllable dissipative superbehaviour. We prove embeddability results and use them to resolve the fallacy in the example termed 'lossless' due to unobservable storage functions. We next show that, quite unreasonably, the embeddability definition admits behaviours that are both strictly dissipative and strictly antidissipative. Drawbacks of the embeddability definition in the context of RLC circuits are
Kudinov, V. A.; Eremin, A. V.; Kudinov, I. V.
2017-11-01
The differential equation of heat transfer with allowance for energy dissipation and spatial and temporal nonlocality has been derived by the relaxation of heat flux and temperature gradient in the Fourier law formula for the heat flux at the use of the heat balance equation. An investigation of the numerical solution of the heat-transfer problem at a laminar fluid flow in a plane duct has shown the impossibility of an instantaneous acceptance of the boundary condition of the first kind — the process of its settling at small values of relaxation coefficients takes a finite time interval the duration of which is determined by the thermophysical and relaxation properties of the fluid. At large values of relaxation coefficients, the use of the boundary condition of the first kind is possible only at Fo → ∞. The friction heat consideration leads to the alteration of temperature profiles, which is due to the rise of the intervals of elevated temperatures in the zone of the maximal velocity gradients. With increasing relaxation coefficients, the smoothing of temperature profiles occurs, and at their certain high values, the fluid cooling occurs at a gradientless temperature variation along the transverse spatial variable and, consequently, the temperature proves to be dependent only on time and on longitudinal coordinate.
International Nuclear Information System (INIS)
Toktogulova, D.; Maksimkin, O.; Gusev, M.; Garner, F.
2007-01-01
Full text of publication follows: Much attention is currently being paid in the fusion materials community to modeling of radiation damage and its consequences in structural alloys on mechanical properties. Such activities are best guided with experimental data on the fundamental microstructural and thermodynamic processes involved. This report addresses such fundamental concerns. During plastic deformation of metals some fraction of the externally-applied mechanical energy is converted into heat and is partially accumulated in the form of crystal lattice defects. The thermal release arises from gliding dislocations, their various interactions, their annihilation etc. With respect to irradiated material, one might expect additional heat release caused by interactions of dislocation and radiation-induced defects. To explore this possibility flat mini-tensile specimens of Armco-iron and 12Cr18Ni10Ti stainless steel, both in the annealed condition, were irradiated in the range 2x10 18 to 1.3x10 20 n/cm 2 (E>0.1 MeV) in the WWR-K reactor at T≤350 K. Mechanical tests of both irradiated and non-irradiated specimens were conducted at room temperature in a facility that was a combination of a Calvet calorimeter and a micro-tensile device. This allows simultaneous measurement of mechanical properties and thermodynamic parameters such as deformation work, dissipated heat and latent energy during deformation. The authors derived the kinetics of changes in thermodynamic characteristics versus the deformation level. As the neutron fluence rises, the material's capability to accumulate energy appears to be declining. For example, 12Cr18Ni10Ti irradiated to 1.3x10 20 n/cm 2 did not show any energy accumulation under deformation. In Armco-iron at 1.4x10 19 n/cm 2 the heat release considerably exceeded the deformation work value. The authors assume that such effects might be related with annihilation of point defects and their complexes introduced during irradiation. To test this
Nuclear Dissipation from Fission Time
International Nuclear Information System (INIS)
Gontchar, I.; Morjean, M.; Basnary, S.
2000-01-01
Fission times, pre-scission neutron multiplicities and GDR pre-scission γ-ray multiplicities measured for uranium or thorium nuclei formed with temperatures T ∼ 1.8 MeV have been compared with calculations performed with CDSM2, a two-dimensional dynamical model combined with a statistical one. Among the three experimental approaches considered, fission times give access to the most precise pieces of information on nuclear dissipation at high excitation energy. For the temperature range under consideration, an agreement between the model and data is achieved if one-body dissipation is used with a strength factor k red ∼ 0.45 ± 0.10 applied to the wall term for the mononuclear configuration. (authors)
Notari, Alessio
2016-12-22
We analyze in detail the background cosmological evolution of a scalar field coupled to a massless abelian gauge field through an axial term $\\frac{\\phi}{f_\\gamma} F \\tilde{F}$, such as in the case of an axion. Gauge fields in this case are known to experience tachyonic growth and therefore can backreact on the background as an effective dissipation into radiation energy density $\\rho_R$, which which can lead to inflation without the need of a flat potential. We analyze the system, for momenta $k$ smaller than the cutoff $f_\\gamma$, including numerically the backreaction. We consider the evolution from a given static initial condition and explicitly show that, if $f_\\gamma$ is smaller than the field excursion $\\phi_0$ by about a factor of at least ${\\cal O} (20)$, there is a friction effect which turns on before that the field can fall down and which can then lead to a very long stage of inflation with a generic potential. In addition we find superimposed oscillations, which would get imprinted on any kind of...
Electromagnetic Energy Absorption due to Wireless Energy Transfer: A Brief Review
Directory of Open Access Journals (Sweden)
Syafiq A.
2016-01-01
Full Text Available This paper reviews an implementation of evaluating compliance of wireless power transfer systems with respect to human electromagnetic exposure limits. Methods for both numerical analysis and measurements are discussed. The objective is to evaluate the rate of which energy is absorbed by the human body when exposed to a wireless energy transfer, although it can be referred to the absorption of other forms of energy by tissue. An exposure assessment of a representative wireless power transfer system, under a limited set of operating conditions, is provided in order to estimate the maximum SAR levels. The aim of this review is to conclude the possible side effect to the human body when utilizing wireless charging in daily life so that an early severe action can be taken when using wireless transfer.
Monitoring and modeling shoreline response due to shoreface nourishment on a high-energy coast
Barnard, P. L.; Erikson, Li H.; Hansen, J. E.
2009-01-01
Shoreface nourishment can be an efficient technique to feed sediment into the littoral zone without the order of magnitude cost increase incurred by directly nourishing the beach. An erosion hot spot at Ocean Beach in San Francisco, California, USA, threatens valuable public infrastructure as well as safe recreational use of the beach. In an effort to reduce the erosion at this location, a new beneficial reuse plan was implemented in May 2005 for the sediment dredged annually from the main shipping channel at the mouth of San Francisco Bay. From 2005 to 2007, approximately 230,000 m of sand was placed annually at depths between 9 and 14 m, in a location where strong tidal currents and open-ocean waves could potentially feed sediment onto the section of beach experiencing critical erosion. The evolution of the disposal mound and adjacent beach were monitored with 12 multibeam bathymetric surveys, and over 40 high-resolution beach topographic surveys. In addition, sediment transport processes were investigated using sediment grab samples, acoustic Doppler profilers, and two separate models: a cross-shore profile model (UNIBEST-TC) and a coastal area model (Delft3D). The results of the monitoring and modeling demonstrate that the disposal mound may be effective in dissipating wave energy striking this vulnerable stretch of coast with negligible shadowing effects, but a positive shoreline response can only be achieved by placing the sediment in water depths less than 5 m.
Dissipative soliton acceleration in nonlinear optical lattices.
Kominis, Yannis; Papagiannis, Panagiotis; Droulias, Sotiris
2012-07-30
An effective mechanism for dissipative soliton acceleration in nonlinear optical lattices under the presence of linear gain and nonlinear loss is presented. The key idea for soliton acceleration consists of the dynamical reduction of the amplitude of the effective potential experienced by the soliton so that its kinetic energy eventually increases. This is possible through the dependence of the effective potential amplitude on the soliton mass, which can be varied due to the presence of gain and loss mechanisms. In contrast to the case where either the linear or the nonlinear refractive index is spatially modulated, we show that when both indices are modulated with the same period we can have soliton acceleration and mass increasing as well as stable soliton propagation with constant non-oscillating velocity. The acceleration mechanism is shown to be very robust for a wide range of configurations.
International Nuclear Information System (INIS)
Mahlia, T.M.I.
2004-01-01
There are many papers that have been published on energy efficiency standards and labels. However, a very limited number of articles on the subject have discussed the transformation of appliance energy efficiency in the market after the programs are implemented. This paper is an attempt to investigate the market transformation due to implementation of minimum energy efficiency standards and energy labels. Even though the paper only investigates room air conditioners as a case study, the method is also applicable for predicting market transformation for other household electrical appliances
International Nuclear Information System (INIS)
Agodi, C.; Alba, R.; Anzalone, A.; Coniglione, R.; Zoppo, A. del; Finocchiaro, P.; Maiolino, C.; Papa, M.; Piattelli, P.; Sapienza, P.; Wang, Q.; DeRosa, A.; Fioretto, E.; Inglima, G.; Romoli, M.; Sandoli, M.
1991-01-01
Photons emitted in the 28 Si+ 64 Ni and 32 S+ 64 Ni reactions at 143 MeV and 156 MeV incident energy respectively, have been detected in coincidence with the ejected charged fragments. An array of 48 BaF 2 γ-rays detector and 6 solid state silicon detector telescopes have been used. Photon energy spectra measured in the energy range from 2 to 20 MeV in coincidence with ejectiles coming from deep inelastic reactions, are consistent with statistical emission from the reaction products. (orig.)
Energy Technology Data Exchange (ETDEWEB)
Agodi, C.; Alba, R.; Anzalone, A.; Coniglione, R.; Zoppo, A. del; Finocchiaro, P.; Maiolino, C.; Papa, M.; Piattelli, P.; Sapienza, P.; Wang, Q. (Istituto Nazionale di Fisica Nucleare, Catania (Italy). Lab. Nazionale del Sud); Bellia, G.; Cavallaro, S.; Migneco, E.; Pappalardo, G.; Rizzo, F.; Russo, G. (Catania Univ. (Italy). Dipt. di Fisica Istituto Nazionale di Fisica Nucleare, Catania (Italy). Lab. Nazionale del Sud); Cardella, G.; Wang, G.S. (Istituto Nazionale di Fisica Nucleare, Catania (Italy)); DeRosa, A.; Fioretto, E.; Inglima, G.; Romoli, M.; Sandoli, M. (Naples-2 Univ. (Italy). Dipt. di Scienze Fisiche Istituto Nazionale di Fisica Nucleare, Naples (Italy))
1991-11-01
Photons emitted in the {sup 28}Si+{sup 64}Ni and {sup 32}S+{sup 64}Ni reactions at 143 MeV and 156 MeV incident energy respectively, have been detected in coincidence with the ejected charged fragments. An array of 48 BaF{sub 2} {gamma}-rays detector and 6 solid state silicon detector telescopes have been used. Photon energy spectra measured in the energy range from 2 to 20 MeV in coincidence with ejectiles coming from deep inelastic reactions, are consistent with statistical emission from the reaction products. (orig.).
Sudden viscous dissipation in compressing plasma turbulence
Davidovits, Seth; Fisch, Nathaniel
2015-11-01
Compression of a turbulent plasma or fluid can cause amplification of the turbulent kinetic energy, if the compression is fast compared to the turnover and viscous dissipation times of the turbulent eddies. The consideration of compressing turbulent flows in inviscid fluids has been motivated by the suggestion that amplification of turbulent kinetic energy occurred on experiments at the Weizmann Institute of Science Z-Pinch. We demonstrate a sudden viscous dissipation mechanism whereby this amplified turbulent kinetic energy is rapidly converted into thermal energy, which further increases the temperature, feeding back to further enhance the dissipation. Application of this mechanism in compression experiments may be advantageous, if the plasma can be kept comparatively cold during much of the compression, reducing radiation and conduction losses, until the plasma suddenly becomes hot. This work was supported by DOE through contract 67350-9960 (Prime # DOE DE-NA0001836) and by the DTRA.
Phenomenological approaches of dissipative heavy ion collisions
International Nuclear Information System (INIS)
Ngo, C.
1983-09-01
These lectures describe the properties of dissipative heavy ion collisions observed in low bombarding energy heavy ion reactions. These dissipative collisions are of two different types: fusion and deep inelastic reactions. Their main experimental properties are described on selected examples. It is shown how it is possible to give a simple interpretation to the data. A large number of phenomenological models have been developped to understand dissipative heavy ion collisions. The most important are those describing the collision by classical mechanics and friction forces, the diffusion models, and transport theories which merge both preceding approaches. A special emphasis has been done on two phenomena observed in dissipative heavy ion collisions: charge equilibratium for which we can show the existence of quantum fluctuations, and fast fission which appears as an intermediate mechanism between deep inelastic reactions and compound nucleus formation [fr
Field observations of turbulent dissipation rate profiles immediately below the air-water interface
Wang, Binbin; Liao, Qian
2016-06-01
Near surface profiles of turbulence immediately below the air-water interface were measured with a free-floating Particle Image Velocimetry (PIV) system on Lake Michigan. The surface-following configuration allowed the system to measure the statistics of the aqueous-side turbulence in the topmost layer immediately below the water surface (z≈0˜15 cm, z points downward with 0 at the interface). Profiles of turbulent dissipation rate (ɛ) were investigated under a variety of wind and wave conditions. Various methods were applied to estimate the dissipation rate. Results suggest that these methods yield consistent dissipation rate profiles with reasonable scattering. In general, the dissipation rate decreases from the water surface following a power law relation in the top layer, ɛ˜z-0.7, i.e., the slope of the decrease was lower than that predicted by the wall turbulence theory, and the dissipation was considerably higher in the top layer for cases with higher wave ages. The measured dissipation rate profiles collapse when they were normalized with the wave speed, wave height, water-side friction velocity, and the wave age. This scaling suggests that the enhanced turbulence may be attributed to the additional source of turbulent kinetic energy (TKE) at the "skin layer" (likely due to micro-breaking), and its downward transport in the water column.
Neutrino Energy Loss Rates due to 54,55,56Fe in Stellar Environment
International Nuclear Information System (INIS)
Nabi, Jameel-Un
2010-01-01
Neutrino energy loss rates are required as a key nuclear physics input parameter in the simulation codes of core-collapse supernovae of massive stars. The weak interaction rates due to isotopes of iron, 54,55,56 Fe, are considered to play an important role during the presupernova evolution of massive stars. Proton-neutron quasi-particle random phase approximation (pn-QRPA) theory has recently being used for a microscopic calculation of stellar weak interaction rates of iron isotopes with success. The calculation of neutrino energy loss rates due to 54,55,56 Fe is presented along with a comparison with large scale shell model results.
Fujisawa, Jun-ichi
2015-05-14
Interfacial charge-transfer (ICT) transitions are expected to be a novel charge-separation mechanism for efficient photovoltaic conversion featuring one-step charge separation without energy loss. Photovoltaic conversion due to ICT transitions has been investigated using several TiO2-organic hybrid materials that show organic-to-inorganic ICT transitions in the visible region. In applications of ICT transitions to photovoltaic conversion, there is a significant problem that rapid carrier recombination is caused by organic-inorganic electronic coupling that is necessary for the ICT transitions. In order to solve this problem, in this work, I have theoretically studied light-to-current conversions due to the ICT transitions on the basis of the Marcus theory with density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations. An apparent correlation between the reported incident photon-to-current conversion efficiencies (IPCE) and calculated reorganization energies was clearly found, in which the IPCE increases with decreasing the reorganization energy consistent with the Marcus theory in the inverted region. This activation-energy dependence was systematically explained by the equation formulated by the Marcus theory based on a simple excited-state kinetic scheme. This result indicates that the reduction of the reorganization energy can suppress the carrier recombination and enhance the IPCE. The reorganization energy is predominantly governed by the structural change in the chemical-adsorption moiety between the ground and ICT excited states. This work provides crucial knowledge for efficient photovoltaic conversion due to ICT transitions.
Dissipative Continuous Spontaneous Localization (CSL) model.
Smirne, Andrea; Bassi, Angelo
2015-08-05
Collapse models explain the absence of quantum superpositions at the macroscopic scale, while giving practically the same predictions as quantum mechanics for microscopic systems. The Continuous Spontaneous Localization (CSL) model is the most refined and studied among collapse models. A well-known problem of this model, and of similar ones, is the steady and unlimited increase of the energy induced by the collapse noise. Here we present the dissipative version of the CSL model, which guarantees a finite energy during the entire system's evolution, thus making a crucial step toward a realistic energy-conserving collapse model. This is achieved by introducing a non-linear stochastic modification of the Schrödinger equation, which represents the action of a dissipative finite-temperature collapse noise. The possibility to introduce dissipation within collapse models in a consistent way will have relevant impact on the experimental investigations of the CSL model, and therefore also on the testability of the quantum superposition principle.
Designing Biomimetic, Dissipative Material Systems
Energy Technology Data Exchange (ETDEWEB)
Balazs, Anna C. [Univ. of Pittsburgh, PA (United States). Chemical Engineering Dept.; Whitesides, George M. [Harvard Univ., Cambridge, MA (United States). Dept. of Chemistry and Chemical Biology; Brinker, C. Jeffrey [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Chemical and Nuclear Engineering. Dept. of Chemistry. Dept. of Molecular Genetics and Microbiology. Center for Micro-Engineered Materials; Aranson, Igor S. [UChicago, LLC., Argonne, IL (United States); Chaikin, Paul [New York Univ. (NYU), NY (United States). Dept. of Physics; Dogic, Zvonimir [Brandeis Univ., Waltham, MA (United States). Dept. of Physics; Glotzer, Sharon [Univ. of Michigan, Ann Arbor, MI (United States). Dept. of Chemical Engineering. Dept. of Materials Science and Engineering. Dept. of Macromolecular Science and Engineering Physics; Hammer, Daniel [Univ. of Pennsylvania, Philadelphia, PA (United States). School of Engineering and Applied Science; Irvine, Darrell [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States). Dept. of Materials Science and Engineering and Biological Engineering; Little, Steven R. [Univ. of Pittsburgh, PA (United States). Chemical Engineering Dept.; Olvera de la Cruz, Monica [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering; Parikh, Atul N. [Univ. of California, Davis, CA (United States). Dept. of Biomedical Engineering. Dept. of Chemical Engineering and Materials Science; Stupp, Samuel [Northwestern Univ., Evanston, IL (United States). Dept. of Materials Science and Engineering. Dept. of Chemistry. Dept. of Medicine. Dept. of Biomedical Engineering; Szostak, Jack [Harvard Univ., Cambridge, MA (United States). Dept. of Chemistry and Chemical Biology
2016-01-21
Throughout human history, new materials have been the foundation of transformative technologies: from bronze, paper, and ceramics to steel, silicon, and polymers, each material has enabled far-reaching advances. Today, another new class of materials is emerging—one with both the potential to provide radically new functions and to challenge our notion of what constitutes a “material”. These materials would harvest, transduce, or dissipate energy to perform autonomous, dynamic functions that mimic the behaviors of living organisms. Herein, we discuss the challenges and benefits of creating “dissipative” materials that can potentially blur the boundaries between living and non-living matter.
Chemical absorption of acoustic energy due to an eddy in the western Bay of Bengal
Digital Repository Service at National Institute of Oceanography (India)
PrasannaKumar, S.; Navelkar, G.S.; Murty, T.V.R.; Somayajulu, Y.K.; Murty, C
Acoustic energy losses due to chemical absorption, within the western Bay of Bengal, in the presence of a subsurface meso-scale cold core eddy has been analysed. These estimates, for two different frequencies - 400 Hz and 10 kHz, find applications...
Scartazza, Andrea; Di Baccio, Daniela; Bertolotto, Pierangelo; Gavrichkova, Olga; Matteucci, Giorgio
2016-09-01
Forest functionality and productivity are directly related to canopy light interception and can be affected by potential damage from high irradiance. However, the mechanisms by which leaves adapt to the variable light environments along the multilayer canopy profile are still poorly known. We explored the leaf morphophysiological and metabolic responses to the natural light gradient in a pure European beech (Fagus sylvatica L.) forest at three different canopy heights (top, middle and bottom). Structural adjustment through light-dependent modifications in leaf mass per area was the reason for most of the variations in photosynthetic capacity. The different leaf morphology along the canopy influenced nitrogen (N) partitioning, water- and photosynthetic N-use efficiency, chlorophyll (Chl) fluorescence and quali-quantitative contents of photosynthetic pigments. The Chl a to Chl b ratio and the pool of xanthophyll-cycle pigments (VAZ) increased at the highest irradiance, as well as lutein and β-carotene. The total pool of ascorbate and phenols was higher in leaves of the top and middle canopy layers when compared with the bottom layer, where the ascorbate peroxidase was relatively more activated. The non-photochemical quenching was strongly and positively related to the VAZ/(Chl a + b) ratio, while Chl a/Chl b was related to the photochemical efficiency of photosystem II. Along the multilayer canopy profile, the high energy dissipation capacity of leaves was correlated to an elevated redox potential of antioxidants. The middle layer gave the most relevant contribution to leaf area index and carboxylation capacity of the canopy. In conclusion, a complex interplay among structural, physiological and biochemical traits drives the dynamic leaf acclimation to the natural gradients of variable light environments along the tree canopy profile. The relevant differences observed in leaf traits within the canopy positions of the beech forest should be considered for
Wang, Chi; Hsiue, Ting-Ting
2017-09-11
Through single-tube electrospinning, the biodegradable core-shell fibers of poly(3-hydroxybutyrate) (PHB) and poly(d,l-lactic acid) (PDLLA) were obtained from blend solutions with different compositions at a total polymer concentration of 7 wt %. Regardless whether PHB is the major or minor component (PHB/PDLLA = 90/10, 75/25, 50/50, and 25/75 wt. ratio), these phase-separated solutions all yielded core-shell fibers with PHB as core and PDLLA as shell. A new scenario of core-shell fiber formation was proposed on the basis of the relative magnitude of the intrinsic relaxation rate of fluids and external extension rate during electrospinning. The effects of blend compositions on the morphologies of the Taylor cone, whipping jet, and as-spun fibers were investigated. The diameters of core-shell fibers can be tailored by simply varying the PHB/PDLLA ratios. Two scaling laws describing the apparent viscosity (η o ) dependence of the outer fiber diameter (d fo ) and core fiber diameter (d fc ) were derived. That is, d fo ∼ η o 0.38 and d fc ∼ η o 0.86 . The microstructures of the as-spun fibers were determined by differential scanning calorimetry, Fourier transform infrared spectroscopy, and synchrotron wide-angle and small-angle X-ray scatterings. Results showed that the PDLLA component was in the amorphous state, and the crystallizability of PHB component remained unchanged, except the amorphous 10/90 fibers electrospun from a miscible solution state. The synergistic mechanical properties of the core-shell fibers were obtained, along with the ductile PDLLA shell enclosing the brittle PHB core. The enhanced toughness was attributed to the fragmentation of the brittle PHB core and necking fracture of the ductile PDLLA shell, which served as an effective route for energy dissipation. Compared with the neat PHB fiber, the 90/10 and 75/25 core-shell fibers possessed larger elastic moduli, which was attributed to the high PHB crystal orientation in their core sections
Graphene heat dissipating structure
Washburn, Cody M.; Lambert, Timothy N.; Wheeler, David R.; Rodenbeck, Christopher T.; Railkar, Tarak A.
2017-08-01
Various technologies presented herein relate to forming one or more heat dissipating structures (e.g., heat spreaders and/or heat sinks) on a substrate, wherein the substrate forms part of an electronic component. The heat dissipating structures are formed from graphene, with advantage being taken of the high thermal conductivity of graphene. The graphene (e.g., in flake form) is attached to a diazonium molecule, and further, the diazonium molecule is utilized to attach the graphene to material forming the substrate. A surface of the substrate is treated to comprise oxide-containing regions and also oxide-free regions having underlying silicon exposed. The diazonium molecule attaches to the oxide-free regions, wherein the diazonium molecule bonds (e.g., covalently) to the exposed silicon. Attachment of the diazonium plus graphene molecule is optionally repeated to enable formation of a heat dissipating structure of a required height.
Stable low-dissipation schemes for turbulent compressible flows
Subbareddy, Pramod Kumar V.
Shock capturing schemes, which are commonly used in compressible flow simulations, introduce excessive amounts of numerical viscosity which smears out small scale flow features. A few low-dissipation methods have been proposed in the recent literature. They are more selective in the sense that they explicitly identify the portion of the numerical flux that is diffusive and damp its effect in 'smooth' regions of the flow. This work employs flux vector splitting methods; the dissipative portions of the Steger-Warming schemes are explicitly identified and various shock detection switches are explored. For high Reynolds number flows, especially when the energetic scales are close to the Nyquist limits of the grids used, aliasing errors become noticeable. These high frequency oscillations that arise due to the nonlinear nature of the Navier-Stokes equations cause solutions to become unstable. When dissipative methods are used, these errors are suppressed; however when using low-dissipation schemes, they can be prominent and need to be addressed by some other means. In this thesis, we focus on methods that enhance stability by enforcing 'secondary conservation' - the fluxes are constrained in such a way that a conservation law for a secondary, positive quantity is also satisified. In particular, we focus on kinetic energy, and a fully discrete (in time and space) 'kinetic energy consistent' scheme is derived and tested. Hybrid RAMS-LES methods such as Detached Eddy Simulations are necessary in order to make simulations of high speed flows with attached boundary layers affordable. A popular DES model is based on the Spalart-Allmaras RANS equation; a minor modification to the length scale makes the model behave in a hybrid manner. The S-A model itself was constructed using mostly empirical arguments by the authors. This model is analyzed and its connection to other turbulence models, in particular, the ksgs equation, is explored. A dynamic version of the model is proposed
Directory of Open Access Journals (Sweden)
Xiuli Wu
2018-03-01
Full Text Available Renewable energy is an alternative to non-renewable energy to reduce the carbon footprint of manufacturing systems. Finding out how to make an alternative energy-efficient scheduling solution when renewable and non-renewable energy drives production is of great importance. In this paper, a multi-objective flexible flow shop scheduling problem that considers variable processing time due to renewable energy (MFFSP-VPTRE is studied. First, the optimization model of the MFFSP-VPTRE is formulated considering the periodicity of renewable energy and the limitations of energy storage capacity. Then, a hybrid non-dominated sorting genetic algorithm with variable local search (HNSGA-II is proposed to solve the MFFSP-VPTRE. An operation and machine-based encoding method is employed. A low-carbon scheduling algorithm is presented. Besides the crossover and mutation, a variable local search is used to improve the offspring’s Pareto set. The offspring and the parents are combined and those that dominate more are selected to continue evolving. Finally, two groups of experiments are carried out. The results show that the low-carbon scheduling algorithm can effectively reduce the carbon footprint under the premise of makespan optimization and the HNSGA-II outperforms the traditional NSGA-II and can solve the MFFSP-VPTRE effectively and efficiently.
Optimizing the microstructure of dissipative materials
DEFF Research Database (Denmark)
Andreassen, Erik; Lazarov, Boyan Stefanov; Jensen, Jakob Søndergaard
the material’s loss factor, however, only for large wave lengths (small wave numbers) and constant material parameters (Andreasen et al., 2012). An alternative way to determine the material’s loss factor is to consider the material’s band diagram (Sigalas and Economou, 1992), from which the loss factor can...... from experimental results in (Schaedler, 2011), where a highly energy absorbing material, constructed from structural elements with a small cross sectional area but large area moment of inertia, is presented. Furthermore, the applicability of multiscale finite element methods (Efendiev, 2009......The aim of this work is to present a method to design material microstructures with high dissipation using topology optimization. In order to compute the macroscopic energy dissipation in periodic structures, we focus both on capturing the physical dissipation mechanism and to find the effective...
Microscopic theory of one-body dissipation
International Nuclear Information System (INIS)
Koonin, S.E.; Randrup, J.; Hatch, R.; Kolomietz, V.
1977-01-01
A microscopic theory is developed for nuclear collective motion in the limit of a long nuclear mean-free path. Linear response techniques are applied to an independent particle model and expressions for the collective kinetic energy and rate of energy dissipation are obtained. For leptodermous systems, these quantities are characterized by mass and dissipation kernels coupling the velocities at different points on the nuclear surface. In a classical treatment, the kernels are given in terms of nucleon trajectories within the nuclear shape. In a quantal treatment, the dissipation kernel is related to the nuclear Green function. The spatial and thermal properties of the kernels are investigated. Corrections for the diffuseness of the potential and shell effects are also discussed. (Auth.)
O'Connor, Ewan J.; Illingworth, Anthony J.; Brooks, Ian M.; Westbrook, Christopher D.; Hogan, Robin J.; Davies, Fay; Brooks, Barbara J.
2010-01-01
A method of estimating dissipation rates from a vertically pointing Doppler lidar with high temporal and spatial resolution has been evaluated by comparison with independent measurements derived from a balloon-borne sonic anemometer. This method utilizes the variance of the mean Doppler velocity from a number of sequential samples and requires an estimate of the horizontal wind speed. The noise contribution to the variance can be estimated from the observed signal-to-noise ratio and removed w...
Energy deposition in the earth's atmosphere due to impact of solar activity-generated disturbances
Wu, S. T.; Kan, L. C.; Tandberg-Hanssen, E.; Dryer, M.
1979-01-01
Energy deposition in and dynamic responses of the terrestrial atmosphere to solar flare-generated shocks and other physical processes - such as particle precipitation and local heating - are investigated self-consistently in the context of hydrodynamics, the problem being treated as an initial boundary-value problem. It is extremely difficult to construct a general model for the line solar activity-magnetosphere-atmosphere; however, a limited model for this link is possible. The paper describes such a model, and presents some results on energy deposition into the earth's atmosphere due to solar activity-generated disturbances. Results from the present calculations are presented and discussed.
Study in mutation of alfalfa genome DNA due to low energy N+ implantation using RAPD
International Nuclear Information System (INIS)
Chen Roulei; Song Daojun; Yu Zengliang; Li Yufeng; Liang Yunzhang
2001-01-01
After implanted by various dosage N + beams, germination rate of alfalfa seeds appears to be saddle line with dosage increasing. The authors have studied in mutation of genome DNA due to low energy N + implantation, and concluded that 30 differential DNA fragments have been amplified by 8 primers (S 41 , S 42 , S 45 , S 46 , S 50 , S 52 , S 56 , S 58 ) in 100 primers, moreover, number of differential DNA fragments between CK and treatments increases with dosage. Consequently, low energy ion implantation can cause mutation of alfalfa genome DNA. The more dosage it is, the more mutation alfalfa will be
Dissipative distributed systems
Willems, JC; Djaferis, TE; Schick, IC
2000-01-01
A controllable distributed dynamical system described by a system of linear constant-coefficient partial differential equations is said to be conservative if for compact support trajectories the integral of the supply rate is zero. It is said to be dissipative if this integral is non-negative. The
Collective variables and dissipation
International Nuclear Information System (INIS)
Balian, R.
1984-09-01
This is an introduction to some basic concepts of non-equilibrium statistical mechanics. We emphasize in particular the relevant entropy relative to a given set of collective variables, the meaning of the projection method in the Liouville space, its use to establish the generalized transport equations for these variables, and the interpretation of dissipation in the framework of information theory
Energy Technology Data Exchange (ETDEWEB)
Piacentino, Antonio; Cardona, Fabio [DREAM - Department of Energy and Environmental Researches, University of Palermo, Viale delle Scienze, 90128 Palermo (Italy)
2010-03-15
The authors of the main thermoeconomic methodologies developed in the last two decades have recently focused their efforts on the analysis of dissipative devices, i.e. those components whose productive purpose is neither intuitive nor easy to define. Coherent and unanimously accepted cost structures have been identified for dissipative components, while ambiguities still exist as concerns the cost allocation principles to be adopted. Being this aspect evidently cost-influencing, accurate analyses focused on the subjectivity of results are needed. This paper is structured in two parts. In the Part I an in-depth study of some critical issues arising from the thermoeconomic analysis of a 1.5 MW{sub c} industrial chiller is presented. The attention is focused on the role of the condenser and the throttling valve (considered as a limit condition for an expander with very low isentropic efficiency); marginal analyses performed on the condensation pressure and the isentropic efficiency of the expander provided elements to assess the rational of the cost allocation principles. Attempting to refugee any cost allocation criterion based on postulates, the concept of Scope is identified as a possible non-arbitrary basis for cost allocation in dissipative devices; consequently, a new topology is defined, abandoning the conventional classification between dissipative and productive units, toward a new distinction between Product Makers and Product Takers functions. The proposed approach is applied to the cost accounting of the examined chiller, revealing inadequate and less explicative than the conventional thermoeconomic approaches due to its ''intrinsically differential'' nature. In the Part II of this paper the proposed approach will be applied to an Optimization problem, revealing very flexible and insightful. (author)
Calculating the X-Ray Fluorescence from the Planet Mercury Due to High-Energy Electrons
Burbine, T. H.; Trombka, J. I.; Bergstrom, P. M., Jr.; Christon, S. P.
2005-01-01
The least-studied terrestrial planet is Mercury due to its proximity to the Sun, which makes telescopic observations and spacecraft encounters difficult. Our lack of knowledge about Mercury should change in the near future due to the recent launching of MESSENGER, a Mercury orbiter. Another mission (BepiColombo) is currently being planned. The x-ray spectrometer on MESSENGER (and planned for BepiColombo) can characterize the elemental composition of a planetary surface by measuring emitted fluorescent x-rays. If electrons are ejected from an atom s inner shell by interaction with energetic particles such as photons, electrons, or ions, electrons from an outer shell can transfer to the inner shell. Characteristic x-rays are then emitted with energies that are the difference between the binding energy of the ion in its excited state and that of the ion in its ground state. Because each element has a unique set of energy levels, each element emits x-rays at a unique set of energies. Electrons and ions usually do not have the needed flux at high energies to cause significant x-ray fluorescence on most planetary bodies. This is not the case for Mercury where high-energy particles were detected during the Mariner 10 flybys. Mercury has an intrinsic magnetic field that deflects the solar wind, resulting in a bow shock in the solar wind and a magnetospheric cavity. Electrons and ions accelerated in the magnetosphere tend to follow its magnetic field lines and can impact the surface on Mercury s dark side Modeling has been done to determine if x-ray fluorescence resulting from the impact of high-energy electrons accelerated in Mercury's magnetosphere can be detected by MESSENGER. Our goal is to understand how much bulk chemical information can be obtained from x-ray fluorescence measurements on the dark side of Mercury.
Transformation of energy and momentum due to Landau damping in time
International Nuclear Information System (INIS)
Lacina, J.
1992-01-01
The physical mechanism of the Landau damping is discussed and the general expressions for the transformation of energy and momentum due to Landau damping in time are derived. The presented theory is not limited to a small decrement to the wave frequency ratio and it removes some artificial assumptions and discrepancies involved in older theoretical models. The perturbation of particle velocities, caused by self-consistent electric fields, is shown to be formed by a superposition of free and forced coherent oscillations propagating in space. Thus, the transformation of energy and momentum may be treated as a process of phase interference between these two types of oscillations, in which the evolution of the forced oscillations is governed by the energy and momentum balance equations. (J.U.) 13 refs
Kambly, Kiran; Bradley, Thomas H.
2015-02-01
Electric vehicles (EVs) are vehicles that are propelled by electric motors powered by rechargeable battery. They are generally asserted to have GHG emissions, driveability and life cycle cost benefits over conventional vehicles. Despite this, EVs face significant challenges due to their limited on-board energy storage capacity. In addition to providing energy for traction, the energy storage device operates HVAC systems for cabin conditioning. This results in reduced driving range. The factors such as local ambient temperature, local solar radiation, local humidity, duration and thermal soak have been identified to affect the cabin conditions. In this paper, the development of a detailed system-level approach to HVAC energy consumption in EVs as a function of transient environmental parameters is described. The resulting vehicle thermal comfort model is used to address several questions such as 1) How does day to day environmental conditions affect EV range? 2) How does frequency of EV range change geographically? 3) How does trip start time affect EV range? 4) Under what conditions does cabin preconditioning assist in increasing the EV range? 5) What percentage increase in EV range can be expected due to cabin preconditioning at a given location?
Alhamdi, Sabah F. H.; Bailey, Sean C. C.
2017-11-01
Measurements of the small-scale dissipation statistics of turbulent boundary layer flows with and without free-stream turbulence are reported for Reτ ≈ 1000 (Reθ ≈ 2000). The scaling of the dissipation scale distribution is examined in these two boundary conditions. Results demonstrated that the local large-scale Reynolds number based on the measured longitudinal integral length scale fails to properly normalize the dissipation scale distribution near the wall in these two free-stream conditions due to the imperfect characterization of the upper bound of the inertial cascade by the integral length scale. A surrogate found from turbulent kinetic energy and mean dissipation rate only moderately improved the scaling of the dissipation scales, relative to the measured integral length scale. When a length scale based on the distance from the wall [as suggested by Bailey and Witte, "On the universality of local dissipation scales in turbulent channel flow," J. Fluid Mech. 786, 234-252 (2015)] was utilized to scale the dissipation scale distribution, in the region near the wall, there was a noticeable improvement in the collapse of the normalized distribution of dissipation scales. In addition, unlike in channel flows, in the outer layer of the turbulent boundary layer, the normalized distributions of the local dissipation scales were observed to be dependent on the wall-normal position. This was found to be attributable to the presence of external intermittency in the outer layer as the presence of free-stream turbulence was found to restore the scaling behavior by replacing the intermittent laminar flow with turbulent flow.
Estimating Half-Lives for Pesticide Dissipation from Plants
DEFF Research Database (Denmark)
Fantke, Peter; Gillespie, Brenda W.; Juraske, Ronnie
2014-01-01
Pesticide risk and impact assessment models critically rely on and are sensitive to information describing dissipation from plants. Despite recent progress, experimental data are not available for all relevant pesticide−plant combinations, and currently no model predicting plant dissipation...... accounts for the influence of substance properties, plant characteristics, temperature, and study conditions. In this study, we propose models to estimate half-lives for pesticide dissipation from plants and provide recommendations for how to use our results. On the basis of fitting experimental...... dissipation data with reported average air temperatures, we estimated a reaction activation energy of 14.25 kJ/mol and a temperature coefficient Q10 of 1.22 to correct dissipation from plants for the influence of temperature. We calculated a set of dissipation half-lives for 333 substances applied at 20 °C...
Morphing of the Dissipative Reaction Mechanism
International Nuclear Information System (INIS)
Schroeder, W.U.; Toke, J.; Gawlikowicz, W.; Houck, M.A.; Lu, J.; Pienkowski, L.
2003-01-01
Important trends in the evolution of heavy-ion reaction mechanisms with bombarding energy and impact parameter are reviewed. Essential features of dissipative reactions appear preserved at E/A = 50-62 MeV, such as dissipative orbiting and multi-nucleon exchange. The relaxation of the A/Z asymmetry with impact parameter is slow. Non-equilibrium emission of light particles and clusters is an important process accompanying the evolution of the mechanism. Evidence is presented for a new mechanism of statistical cluster emission from hot, metastable primary reaction products, driven by surface entropy. These results suggest a plausible reinterpretation of multi-fragmentation. (authors)
Foucault Dissipation in a Rolling Cylinder: A Webcam Quantitative Study
Bonanno, A.; Bozzo, G.; Camarca, M.; Sapia, P.
2011-01-01
In this paper we present an experimental strategy to measure the micro power dissipation due to Foucault "eddy" currents in a copper cylinder rolling on two parallel conductive rails in the presence of a magnetic field. Foucault power dissipation is obtained from kinematical measurements carried out by using a common PC webcam and video analysis…
Transient chaotic transport in dissipative drift motion
Energy Technology Data Exchange (ETDEWEB)
Oyarzabal, R.S. [Pós-Graduação em Ciências/Física, Universidade Estadual de Ponta Grossa, 84030-900, Ponta Grossa, PR (Brazil); Szezech, J.D. [Departamento de Matemática e Estatística, Universidade Estadual de Ponta Grossa, 84030-900, Ponta Grossa, PR (Brazil); Batista, A.M., E-mail: antoniomarcosbatista@gmail.com [Departamento de Matemática e Estatística, Universidade Estadual de Ponta Grossa, 84030-900, Ponta Grossa, PR (Brazil); Souza, S.L.T. de [Departamento de Física e Matemática, Universidade Federal de São João del Rei, 36420-000, Ouro Branco, MG (Brazil); Caldas, I.L. [Instituto de Física, Universidade de São Paulo, 05315-970, São Paulo, SP (Brazil); Viana, R.L. [Departamento de Física, Universidade Federal do Paraná, 81531-990, Curitiba, PR (Brazil); Sanjuán, M.A.F. [Departamento de Física, Universidad Rey Juan Carlos, Tulipán s/n, 28933 Móstoles, Madrid (Spain)
2016-04-22
Highlights: • We consider a situation for which a chaotic transient is present in the dynamics of the two-wave model with damping. • The damping in plasma models can be a way for study a realistic behavior of confinement due the collisional effect. • The escape time as a function of the damping obey a power-law scaling. • We have made a qualitative transport analysis with a simple model that can be useful for more complete models. • We have shown that the pattern of the basin of attraction depends on the damping parameter. - Abstract: We investigate chaotic particle transport in magnetised plasmas with two electrostatic drift waves. Considering dissipation in the drift motion, we verify that the removed KAM surfaces originate periodic attractors with their corresponding basins of attraction. We show that the properties of the basins depend on the dissipation and the space-averaged escape time decays exponentially when the dissipation increases. We find positive finite time Lyapunov exponents in dissipative drift motion, consequently the trajectories exhibit transient chaotic transport. These features indicate how the transient plasma transport depends on the dissipation.
Analysis of Transient Phenomena Due to a Direct Lightning Strike on a Wind Energy System
Directory of Open Access Journals (Sweden)
João P. S. Catalão
2012-07-01
Full Text Available This paper is concerned with the protection of wind energy systems against the direct effects of lightning. As wind power generation undergoes rapid growth, lightning damages involving wind turbines have come to be regarded as a serious problem. Nevertheless, very few studies exist yet in Portugal regarding lightning protection of wind energy systems using numerical codes. A new case study is presented in this paper, based on a wind turbine with an interconnecting transformer, for the analysis of transient phenomena due to a direct lightning strike to the blade. Comprehensive simulation results are provided by using models of the Restructured Version of the Electro-Magnetic Transients Program (EMTP, and conclusions are duly drawn.
Large energy density in three-plate nanocapacitors due to Coulomb blockade
Hubler, A.; Foreman, S.; Liu, J.; Wortsmann, L.
2018-03-01
The maximum energy density of a capacitor is comparatively small due to large leak currents that thermally degrade the system. We study a three-plate system with nanometer gaps between the plates. Two negatively charged plates (cathodes) sandwich a thin, positively charged inner plate (anode). The dynamics of the electrons, in gaps of such a capacitor, are quantized, even at room temperature, because the dimensions are so small. Under strong fields, eigenstates between the electrodes fill and reduce the leak current between the anode and cathode. We show that the self-discharge time for a three-plate nanocapacitor can be significantly longer than a comparable two-plate nanocapacitor, thus increasing maximum energy density of such a nanocapacitor.
Damage evaluation in metal structures subjected to high energy deposition due to particle beams
Peroni, L; Dallocchio, A
2011-01-01
The unprecedented energy intensities of modern hadron accelerators yield special problems with the materials that are placed close to or into the high intensity beams. The energy stored in a single beam of LHC particle accelerator is equivalent to about 80 kg of TNT explosive, stored in a transverse beam area with a typical value of 0.2 mm×0.2 mm. The materials placed close to the beam are used at, or even beyond, their damage limits. However, it is very difficult to predict structural efficiency and robustness accurately: beam-induced damage for high energy and high intensity occurs in a regime where practical experience does not exist. The interaction between high energy particle beams and metals induces a sudden non uniform temperature increase. This provokes a dynamic response of the structure entailing thermal stress waves and thermally induced vibrations or even the failure of the component. This study is performed in order to estimate the damage on a copper component due to the impact with a 7 TeV pro...
Pineda, Evan, J.; Bednarcyk, Brett, A.; Arnold, Steven, M.
2012-01-01
A mesh objective crack band model is implemented in the generalized method of cells (GMC) micromechanics model to predict failure of a composite repeating unit cell (RUC). The micromechanics calculations are achieved using the MAC/GMC core engine within the ImMAC suite of micromechanics codes, developed at the NASA Glenn Research Center. The microscale RUC is linked to a macroscale Abaqus/Standard finite element model using the FEAMAC multiscale framework (included in the ImMAC suite). The effects of the relationship between the characteristic length of the finite element and the size of the microscale RUC on the total energy dissipation of the multiscale model are investigated. A simple 2-D composite square subjected to uniaxial tension is used to demonstrate the effects of scaling the dimensions of the RUC such that the length of the sides of the RUC are equal to the characteristic length of the finite element. These results are compared to simulations where the size of the RUC is fixed, independent of the element size. Simulations are carried out for a variety of mesh densities and element shapes, including square and triangular. Results indicate that a consistent size and shape must be used to yield preserve energy dissipation across the scales.
CO2 emissions due to energy combustion in the World in 2011
International Nuclear Information System (INIS)
Wong, Florine
2014-01-01
This publication presents and comments data, graphs and tables which illustrate the evolution of CO 2 emissions in the world (data are given for different countries and regions of the World), and more particularly those due to energy combustion. These emissions increased in 2011. It also discusses the evolution of CO 2 emission intensity with respect to GDP (1 pc decrease in 2011). When studying emission data with respect to the number of inhabitants, it appears that USA are emitting 20 times more CO 2 per inhabitant than Africa
Allometry and dissipation of ecological flow networks.
Directory of Open Access Journals (Sweden)
Jiang Zhang
Full Text Available BACKGROUND: An ecological flow network is a weighted directed graph in which the nodes are species, the edges are "who eats whom" relationships and the weights are rates of energy or nutrient transferred between species. Allometric scaling is a ubiquitous feature for flow systems such as river basins, vascular networks and food webs. METHODOLOGY: The "ecological network analysis" can serve to reveal hidden allometries, the power law relationship between the throughflux and the indirect impact of node [Formula: see text], directly from the original flow networks without any need to cut edges in the network. The dissipation law, which is another significant scaling relationship between the energy dissipation (respiration and the throughflow of any species, is also obtained from an analysis of the empirical flow networks. Interestingly, the exponents of the allometric law ([Formula: see text] and the dissipation law ([Formula: see text] show a strong relationship for both empirical and simulated flow networks. The dissipation law exponent [Formula: see text], rather than the topology of the network, is the most important factors that affect the allometric exponent [Formula: see text]. CONCLUSIONS: The exponent [Formula: see text] can be interpreted as the degree of centralization of the network, i.e., the concentration of impacts (direct and indirect influences on the entire network along all energy flow pathways on hubs (the nodes with large throughflows. As a result, we find that as [Formula: see text] increases, the relative energy loss of large nodes increases, [Formula: see text] decreases, i.e., the relative importance of large species decreases. Moreover, the entire flow network is more decentralized. Therefore, network flow structure (allometry and thermodynamic constraints (dissipation are linked.
SCALING OF THE ELECTRON DISSIPATION RANGE OF SOLAR WIND TURBULENCE
International Nuclear Information System (INIS)
Sahraoui, F.; Belmont, G.; Rétino, A.; Robert, P.; De Patoul, J.; Huang, S. Y.; Goldstein, M. L.
2013-01-01
Electron scale solar wind (SW) turbulence has attracted great interest in recent years. Considerable evidence exists that the turbulence is not fully dissipated near the proton scale, but continues cascading down to electron scales. However, the scaling of the magnetic energy spectra as well as the nature of the plasma modes involved at those small scales are still not fully determined. Here we survey 10 yr of the Cluster STAFF search-coil magnetometer waveforms measured in the SW and perform a statistical study of the magnetic energy spectra in the frequency range [1, 180] Hz. We found that 75% of the analyzed spectra exhibit breakpoints near the electron gyroscale ρ e , followed by steeper power-law-like spectra. We show that the scaling below the electron breakpoint cannot be determined unambiguously due to instrumental limitations that we discuss in detail. We compare our results to those reported in other studies and discuss their implications for the physical mechanisms involved and for theoretical modeling of energy dissipation in the SW
A Reconnection Switch to Trigger gamma-Ray Burst Jet Dissipation
Energy Technology Data Exchange (ETDEWEB)
McKinney, Jonathan C.; Uzdensky, Dmitri A.
2012-03-14
Prompt gamma-ray burst (GRB) emission requires some mechanism to dissipate an ultrarelativistic jet. Internal shocks or some form of electromagnetic dissipation are candidate mechanisms. Any mechanism needs to answer basic questions, such as what is the origin of variability, what radius does dissipation occur at, and how does efficient prompt emission occur. These mechanisms also need to be consistent with how ultrarelativistic jets form and stay baryon pure despite turbulence and electromagnetic reconnection near the compact object and despite stellar entrainment within the collapsar model. We use the latest magnetohydrodynamical models of ultrarelativistic jets to explore some of these questions in the context of electromagnetic dissipation due to the slow collisional and fast collisionless reconnection mechanisms, as often associated with Sweet-Parker and Petschek reconnection, respectively. For a highly magnetized ultrarelativistic jet and typical collapsar parameters, we find that significant electromagnetic dissipation may be avoided until it proceeds catastrophically near the jet photosphere at large radii (r {approx} 10{sup 13}-10{sup 14}cm), by which the jet obtains a high Lorentz factor ({gamma} {approx} 100-1000), has a luminosity of L{sub j} {approx} 10{sup 50}-10{sup 51} erg s{sup -1}, has observer variability timescales of order 1s (ranging from 0.001-10s), achieves {gamma}{theta}{sub j} {approx} 10-20 (for opening half-angle {theta}{sub j}) and so is able to produce jet breaks, and has comparable energy available for both prompt and afterglow emission. A range of model parameters are investigated and simplified scaling laws are derived. This reconnection switch mechanism allows for highly efficient conversion of electromagnetic energy into prompt emission and associates the observed prompt GRB pulse temporal structure with dissipation timescales of some number of reconnecting current sheets embedded in the jet. We hope this work helps motivate the
Non-dissipative shapable sheet
Oppenheimer, Naomi; Witten, Thomas
2014-03-01
A sheet of paper that has been crumpled and flattened retains some amount of shapability that a bare, uncrumpled, sheet does not have: when deformed by external forces, it retains the deformed shape after the forces are removed. Using a frustrated two dimensional lattice of springs, we show that such shapability can be attained in a non-dissipative system. Numerical investigations suggest an extensive number of bistable energy minima using several variants of this scheme. The numerical sheet can be bent into a nearly-closed cylinder that holds its shape. We verify that the deformed shape is locally stable and compare its bending modulus in the deformed state with that in the initial flat state. We investigate the threshold for non-elastic deformation using various kinds of forcing.
The energy demand in the world in 2004: very strong rise of energy consumptions, mainly due to China
International Nuclear Information System (INIS)
Chateau, Bertrand
2005-01-01
2004, the highest energy growth since 1987: Very strong rise of energy consumptions, strongest annual growth since 1987, due to a favorable economic situation, China is the motor of this evolution. Total energy in the world in 2004: 11,1 Gtep. Asia represents almost one third of the world energy consumption, China's weight (14%) continues to increase by one point every year since 2000. China accounts for 42% of the world energy consumption growth, Asia for 62%. The European consumption growth represents less than 10% of China's growth, and 40% only of USA's growth. Since 2000, coal's market share has increased by 2 points, the oil market share has receded by 1 point. The relative weight of gas remains stable, with 21%. Coal accounts for 37% of the world energy consumption increase in 2004. The oil consumption increase has been more than twice higher than gas increase. Recovery of hydraulic and nuclear power. 78% of coal consumption growth is due to China, 99% from the whole Asia. Since 2000, the strongest growths are in Asia: China, Taiwan, Korea, Japan, India. 50% of the consumption growth is due to the power sector. The oil demand growth accelerates in 2004, driven by China (+14%) and the developing countries. Two giants of the oil demand growth: China and USA (+59 Mt, 58% of total 2004 growth). In the OECD, only North America increases significantly in 2004. Except China, the world growth is relatively steady since 1990, with 1.1%/ year. Oil demand is concentrated on captive usages. 55% of the world demand of oil products is concentrated on transport and petro-chemical sectors (67% in Europe (+ 9 points since 1990) and 81% in North America. Transport and petro-chemical sectors represent 2/3 of the world oil demand growth in 2004. The Middle-East has supplied half of the oil demand increase between 2003 and 2004. Except the Middle-East, only the CIS, Latin America and Africa regions have increased their production in 2004. Despite soaring
Bark beetle-induced tree mortality alters stand energy budgets due to water budget changes
Reed, David E.; Ewers, Brent E.; Pendall, Elise; Frank, John; Kelly, Robert
2018-01-01
Insect outbreaks are major disturbances that affect a land area similar to that of forest fires across North America. The recent mountain pine bark beetle ( D endroctonus ponderosae) outbreak and its associated blue stain fungi ( Grosmannia clavigera) are impacting water partitioning processes of forests in the Rocky Mountain region as the spatially heterogeneous disturbance spreads across the landscape. Water cycling may dramatically change due to increasing spatial heterogeneity from uneven mortality. Water and energy storage within trees and soils may also decrease, due to hydraulic failure and mortality caused by blue stain fungi followed by shifts in the water budget. This forest disturbance was unique in comparison to fire or timber harvesting because water fluxes were altered before significant structural change occurred to the canopy. We investigated the impacts of bark beetles on lodgepole pine ( Pinus contorta) stand and ecosystem level hydrologic processes and the resulting vertical and horizontal spatial variability in energy storage. Bark beetle-impacted stands had on average 57 % higher soil moisture, 1.5 °C higher soil temperature, and 0.8 °C higher tree bole temperature over four growing seasons compared to unimpacted stands. Seasonal latent heat flux was highly correlated with soil moisture. Thus, high mortality levels led to an increase in ecosystem level Bowen ratio as sensible heat fluxes increased yearly and latent heat fluxes varied with soil moisture levels. Decline in canopy biomass (leaf, stem, and branch) was not seen, but ground-to-atmosphere longwave radiation flux increased, as the ground surface was a larger component of the longwave radiation. Variability in soil, latent, and sensible heat flux and radiation measurements increased during the disturbance. Accounting for stand level variability in water and energy fluxes will provide a method to quantify potential drivers of ecosystem processes and services as well as lead to greater
Impact of warmer weather on electricity sector emissions due to building energy use
Meier, Paul; Holloway, Tracey; Patz, Jonathan; Harkey, Monica; Ahl, Doug; Abel, David; Schuetter, Scott; Hackel, Scott
2017-06-01
Most US energy consumption occurs in buildings, with cooling demands anticipated to increase net building electricity use under warmer conditions. The electricity generation units that respond to this demand are major contributors to sulfur dioxide (SO2) and nitrogen oxides (NOx), both of which have direct impacts on public health, and contribute to the formation of secondary pollutants including ozone and fine particulate matter. This study quantifies temperature-driven changes in power plant emissions due to increased use of building air conditioning. We compare an ambient temperature baseline for the Eastern US to a model-calculated mid-century scenario with summer-average temperature increases ranging from 1 C to 5 C across the domain. We find a 7% increase in summer electricity demand and a 32% increase in non-coincident peak demand. Power sector modeling, assuming only limited changes to current generation resources, calculated a 16% increase in emissions of NOx and an 18% increase in emissions of SO2. There is a high level of regional variance in the response of building energy use to climate, and the response of emissions to associated demand. The East North Central census region exhibited the greatest sensitivity of energy demand and associated emissions to climate.
Wave equations with time-dependent dissipation II. Effective dissipation
Wirth, Jens
This article is intended to present a construction of structural representations of solutions to the Cauchy problem for wave equations with time-dependent dissipation above scaling. These representations are used to give estimates of the solution and its derivatives based on L(R), q⩾2. The article represents the second part within a series. In [Jens Wirth, Wave equations with time-dependent dissipation I. Non-effective dissipation, J. Differential Equations 222 (2) (2006) 487-514] weak dissipations below scaling were discussed.
Quantum dynamics in nanoscale magnets in dissipative environments
Miyashita, S; Saito, K; Kobayashi, H.; de Raedt, H.A.
2000-01-01
In discrete energy structure of nanoscale magnets, nonadiabatic transitions at avoided level crossings lead to fundamental processes of dynamics of magnetizations. The thermal environment causes dissipative effects on these processes. In this paper we review the features of the nonadiabatic
Enhancement of Resonant Energy Transfer Due to an Evanescent Wave from the Metal
Energy Technology Data Exchange (ETDEWEB)
Poudel, Amrit [Department; Chen, Xin [Center of Nanomaterials; Ratner, Mark A. [Department
2016-02-29
The high density of evanescent modes in the vicinity of a metal leads to enhancement of the near-field Förster resonant energy transfer (FRET) rate. We present a classical approach to calculate the FRET rate based on the dyadic Green’s function of an arbitrary dielectric environment and consider the nonlocal limit of material permittivity in the case of the metallic half-space and thin film. In a dimer system, we find that the FRET rate is enhanced due to shared evanescent photon modes bridging a donor and an acceptor. Furthermore, a general expression for the FRET rate for multimer systems is derived. The presence of a dielectric environment and the path interference effect enhance the transfer rate, depending on the combination of distance and geometry.
CO2 emissions due to energy combustion in the World in 2008
International Nuclear Information System (INIS)
2010-12-01
This brief document presents and comments tables and figures of statistics about CO 2 emissions due to energy combustion in the World, as these emissions represent more than 95% of the whole CO 2 emissions. Data and statistics are given for different countries, notably the main Western and Asian countries. These emissions are considered globally, but they are also related to the GDP or to the population. If a slight increase (1,5%) of the global emissions has been noticed in 2008, they have decreased when they are related to the GDP (-2%). When emissions are related to the number of inhabitants, it appears that an African emits 20 times less than an inhabitant of the United States of America
CO2 emissions due to energy combustion in the world in 2012
International Nuclear Information System (INIS)
Wong, Florine
2015-01-01
Illustrated by tables and graphs of data, this publication addresses and discusses the evolution of greenhouse gas emissions due to fossil energy combustion and consumption in the world (in the different continents, and in the main regions and countries). It outlines that these CO 2 emissions have increase of 1.2 per cent in 2012 (data are compared on the 1970-2012 period). The evolution of CO 2 emission intensity with respect to GDP is also presented and commented: a 2.1 per cent decrease has been noticed for 2012. The comparison between main geographic and economic areas indicates a 1 to 20 ratio between Africa and the USA for the emission level per capita
Energy loss due to eddy current in linear transformer driver cores
Directory of Open Access Journals (Sweden)
A. A. Kim
2010-07-01
Full Text Available In linear transformer drivers [Phys. Rev. ST Accel. Beams 12, 050402 (2009PRABFM1098-440210.1103/PhysRevSTAB.12.050402; Phys. Rev. ST Accel. Beams 12, 050401 (2009PRABFM1098-440210.1103/PhysRevSTAB.12.050401] as well as any other linear induction accelerator cavities, ferromagnetic cores are used to prevent the current from flowing along the induction cavity walls which are in parallel with the load. But if the core is made of conductive material, the applied voltage pulse generates the eddy current in the core itself which heats the core and therefore also reduces the overall linear transformer driver (LTD efficiency. The energy loss due to generation of the eddy current in the cores depends on the specific resistivity of the core material, the design of the core, as well as on the distribution of the eddy current in the core tape during the remagnetizing process. In this paper we investigate how the eddy current is distributed in a core tape with an arbitrary shape hysteresis loop. Our model is based on the textbook knowledge related to the eddy current generation in ferromagnetics with rectangular hysteresis loop, and in usual conductors. For the reader’s convenience, we reproduce some most important details of this knowledge in our paper. The model predicts that the same core would behave differently depending on how fast the applied voltage pulse is: in the high frequency limit, the equivalent resistance of the core reduces during the pulse whereas in the low frequency limit it is constant. An important inference is that the energy loss due to the eddy current generation can be reduced by increasing the cross section of the core over the minimum value which is required to avoid its saturation. The conclusions of the model are confirmed with experimental observations presented at the end of the paper.
Beta particle energy spectra shift due to self-attenuation effects in environmental sources
Directory of Open Access Journals (Sweden)
Thomas Theakston Alton
2017-10-01
Full Text Available In order to predict and control the environmental and health impacts of ionizing radiation in environmental sources such as groundwater, it is necessary to identify the radionuclides present. Beta-emitting radionuclides are frequently identified by measuring their characteristic energy spectra. The present work shows that self-attenuation effects from volume sources result in a geometry-dependent shift in the characteristic spectra, which needs to be taken into account in order to correctly identify the radionuclides present. These effects are shown to be compounded due to the subsequent shift in the photon spectra produced by the detector, in this case an inorganic solid scintillator (CaF2:Eu monitored using a silicon photomultiplier. Using tritiated water as an environmentally relevant, and notoriously difficult to monitor case study, analytical predictions for the shift in the energy spectra as a function of depth of source have been derived. These predictions have been validated using Geant4 simulations and experimental results measured using bespoke instrumentation.
Parallel magnetic field suppresses dissipation in superconducting nanostrips
Energy Technology Data Exchange (ETDEWEB)
Wang, Yong-Lei; Glatz, Andreas; Kimmel, Gregory J.; Aranson, Igor S.; Thoutam, Laxman R.; Xiao, Zhi-Li; Berdiyorov, Golibjon R.; Peeters, François M.; Crabtree, George W.; Kwok, Wai-Kwong
2017-11-13
The motion of Abrikosov vortices in type-II superconductors results in a finite resistance in the presence of an applied electric current. Elimination or reduction of the resistance via immobilization of vortices is the "holy grail" of superconductivity research. Common wisdom dictates that an increase in the magnetic field escalates the loss of energy since the number of vortices increases. Here we show that this is no longer true if the magnetic field and the current are applied parallel to each other. Our experimental studies on the resistive behavior of a superconducting Mo0.79Ge0.21 nanostrip reveal the emergence of a dissipative state with increasing magnetic field, followed by a pronounced resistance drop, signifying a reentrance to the superconducting state. Large-scale simulations of the 3D time-dependent Ginzburg-Landau model indicate that the intermediate resistive state is due to an unwinding of twisted vortices. When the magnetic field increases, this instability is suppressed due to a better accommodation of the vortex lattice to the pinning configuration. Our findings show that magnetic field and geometrical confinement can suppress the dissipation induced by vortex motion and thus radically improve the performance of superconducting materials.
Parallel magnetic field suppresses dissipation in superconducting nanostrips.
Wang, Yong-Lei; Glatz, Andreas; Kimmel, Gregory J; Aranson, Igor S; Thoutam, Laxman R; Xiao, Zhi-Li; Berdiyorov, Golibjon R; Peeters, François M; Crabtree, George W; Kwok, Wai-Kwong
2017-11-28
The motion of Abrikosov vortices in type-II superconductors results in a finite resistance in the presence of an applied electric current. Elimination or reduction of the resistance via immobilization of vortices is the "holy grail" of superconductivity research. Common wisdom dictates that an increase in the magnetic field escalates the loss of energy since the number of vortices increases. Here we show that this is no longer true if the magnetic field and the current are applied parallel to each other. Our experimental studies on the resistive behavior of a superconducting Mo 0.79 Ge 0.21 nanostrip reveal the emergence of a dissipative state with increasing magnetic field, followed by a pronounced resistance drop, signifying a reentrance to the superconducting state. Large-scale simulations of the 3D time-dependent Ginzburg-Landau model indicate that the intermediate resistive state is due to an unwinding of twisted vortices. When the magnetic field increases, this instability is suppressed due to a better accommodation of the vortex lattice to the pinning configuration. Our findings show that magnetic field and geometrical confinement can suppress the dissipation induced by vortex motion and thus radically improve the performance of superconducting materials.
Estimating half-lives for pesticide dissipation from plants.
Fantke, Peter; Gillespie, Brenda W; Juraske, Ronnie; Jolliet, Olivier
2014-01-01
Pesticide risk and impact assessment models critically rely on and are sensitive to information describing dissipation from plants. Despite recent progress, experimental data are not available for all relevant pesticide-plant combinations, and currently no model predicting plant dissipation accounts for the influence of substance properties, plant characteristics, temperature, and study conditions. In this study, we propose models to estimate half-lives for pesticide dissipation from plants and provide recommendations for how to use our results. On the basis of fitting experimental dissipation data with reported average air temperatures, we estimated a reaction activation energy of 14.25 kJ/mol and a temperature coefficient Q10 of 1.22 to correct dissipation from plants for the influence of temperature. We calculated a set of dissipation half-lives for 333 substances applied at 20 °C under field conditions. Half-lives range from 0.2 days for pyrethrins to 31 days for dalapon. Parameter estimates are provided to correct for specific plant species, temperatures, and study conditions. Finally, we propose a predictive regression model for pesticides without available measured dissipation data to estimate half-lives based on substance properties at the level of chemical substance class. Estimated half-lives from our study are designed to be applied in risk and impact assessment models to either directly describe dissipation or as first proxy for describing degradation.
Directory of Open Access Journals (Sweden)
Xingtuan Yang
2015-01-01
Full Text Available This study investigates the anisotropic characteristics of turbulent energy dissipation rate in a rotating jet flow via direct numerical simulation. The turbulent energy dissipation tensor, including its eigenvalues in the swirling flows with different rotating velocities, is analyzed to investigate the anisotropic characteristics of turbulence and dissipation. In addition, the probability density function of the eigenvalues of turbulence dissipation tensor is presented. The isotropic subrange of PDF always exists in swirling flows relevant to small-scale vortex structure. Thus, with remarkable large-scale vortex breakdown, the isotropic subrange of PDF is reduced in strongly swirling flows, and anisotropic energy dissipation is proven to exist in the core region of the vortex breakdown. More specifically, strong anisotropic turbulence dissipation occurs concentratively in the vortex breakdown region, whereas nearly isotropic turbulence dissipation occurs dispersively in the peripheral region of the strong swirling flows.
Particle exchange as the dissipative mechanism in nucleus-nucleus collisions
International Nuclear Information System (INIS)
Feldmeier, H.; Spangenberger, H.
1984-05-01
We discuss a model where the colliding nuclei are treated as two Germi gases which exchange particles, momentum and entropy through a window in the mean single particle potential. Even at zero temperature transfer of particles is possible because phase space which is not Pauli blocked is available due to unequal Fermi distributions on either side of the window. The difference comes about by a possible mismatch of the mean velocities, of the chemical potentials and of the temperatures. Based on this picture we discuss in a unified manner a variety of dissipative phenomena like mass drift, thermal feed back on the mass drift, partition of excitation energy, energy and angular momentum dissipation, and fluctuations in the relative momentum and mass number. (orig.)
Dissipative processes in light heavy ion collisions
Pop, A.; Andronic, A.; Berceanu, I.; Duma, M.; Moisâ, D.; Petrovici, M.; Simion, V.; Immé, G.; Lanzanò, G.; Pagano, A.; Raciti, G.; Coniglione, R.; Del Zoppo, A.; Piatelli, P.; Sapienza, P.; Colonna, N.; D'Erasmo, G.; Pantaleo, A.
1999-09-01
The characteristics of the dissipative processes in the collisions of light heavy ion systems at incident energies below 10 MeV/nucleon have been studied. The correlations between different experimental observables show similar trends as those known at much heavier systems and semiempirical relationships are established starting from assumptions on the nature of the micro-scopic mechanisms. The charge equilibration process in light systems is also studied.
Dissipative processes in light heavy ion collisions
International Nuclear Information System (INIS)
Pop, A.; Andronic, A.; Berceanu, I.; Duma, M.; Moisa, D.; Petrovici, M.; Simion, V.; Imme, G.; Lanzano, G.; Pagano, A.; Raciti, G.; Coniglione, R.; Del Zoppo, A.; Piatelli, P.; Sapienza, P.; Colonna, N.; D'Erasmo, G.; Pantaleo, A.
1999-01-01
The characteristics of the dissipative processes in the collisions of light heavy ion systems at incident energies below 10 MeV/nucleon have been studied. The correlations between different experimental observables show similar trends as those known at much heavier systems and semiempirical relationships are established starting from assumptions on the nature of the microscopic mechanisms. The charge equilibration process in light systems is also studied. (author)
Spatial Variation of Surface Energy Fluxes Due to Land Use Changes across China
Directory of Open Access Journals (Sweden)
Enjun Ma
2014-04-01
Full Text Available We estimate the heat flux changes caused by the projected land transformation over the next 40 years across China to improve the understanding of the impacts of land dynamics on regional climate. We use the Weather Research and Forecasting (WRF model to investigate these impacts in four representative land transformation zones, where reclamation, overgrazing, afforestation, and urbanization dominates the land use and land cover changes in each zone respectively. As indicated by the significant variance of albedo due to different land use and cover changes, different surface properties cause great spatial variance of the surface flux. From the simulation results, latent heat flux increases by 2 and 21 W/m2 in the reclamation and afforestation regions respectively. On the contrary, overgrazing and urban expansion results in decrease of latent heat flux by 5 and 36 W/m2 correspondingly. Urban expansion leads to an average increase of 40 W/m2 of sensible heat flux in the future 40 years, while reclamation, afforestation, as well as overgrazing result in the decrease of sensible heat flux. Results also show that reclamation and overgrazing lead to net radiation decrease by approximately 4 and 7 W/m2 respectively, however, afforestation and urbanization lead to net radiation increase by 6 and 3 W/m2 respectively. The simulated impacts of projected HLCCs on surface energy fluxes will inform sustainable land management and climate change mitigation.
Bounds on dissipation in stress-driven flow
Tang, W.; Caulfield, C. P.; Young, W. R.
2004-07-01
We calculate the optimal upper and lower bounds, subject to the assumption of streamwise invariance, on the long-time-averaged mechanical energy dissipation rate varepsilon within the flow of an incompressible viscous fluid of constant kinematic viscosity nu and depth h driven by a constant surface stress tau=rho u(2_star) , where u_star is the friction velocity. We show that varepsilon ≤ varepsilon_{max}=tau(2/(rho^2nu)) , i.e. the dissipation is bounded above by the dissipation associated with the laminar solution bu=tau(z+h)/(rhonu) xvec, where xvec is the unit vector in the streamwise x-direction.
Piattelli, P.; Santonocito, D.; Blumenfeld, Y.; Suomijärvi, T.; Agodi, C.; Alamanos, N.; Alba, R.; Auger, F.; Bellia, G.; Chomaz, Ph.; Colonna, M.; Coniglione, R.; del Zoppo, A.; Finocchiaro, P.; Frascaria, N.; Gillibert, A.; Le Faou, J. H.; Loukachine, K.; Maiolino, C.; Migneco, E.; Roynette, J. C.; Sapienza, P.; Scarpaci, J. A.
1998-12-01
High energy -rays ( MeV) have been measured in coincidence with heavy residues emitted in reactions induced by a 37 MeV/u Ar beam on a Mo target.The -ray yield increases strongly with increasing linear momentum transfer indicating the importance of two-body collisions in the transfer mechanism. The high energy -ray multiplicity has been used to correlate the linear momentum transfer to the impact parameter. This correlation is compared to dynamical BNV simulations to show the essential role of two body nucleon-nucleon collisions at these bombarding energies.
Elbelt, Ulf; Schuetz, Tatjana; Knoll, Nina; Burkert, Silke
2015-01-01
Reduced physical activity and almost unlimited availability of food are major contributors to the development of obesity. With the decline of strenuous work, energy expenditure due to spontaneous physical activity has attracted increasing attention. Our aim was to assess changes in energy expenditure, physical activity patterns and nutritional habits in obese subjects aiming at self-directed weight loss. Methods: Energy expenditure and physical activity patterns were measured with a portable ...
Transport theory of dissipative heavy-ion collisions
International Nuclear Information System (INIS)
Norenberg, W.
1979-01-01
The lectures present the formulation of a transport theory, the derivation of a practicable transport equation (Fokker-Planck equation) and the evaluation of transport coefficients for dissipative (or deeply inelastic) heavy-ion collisions. The applicability of the theoretical concept is tested with remarkable success in the analyses of various experimental information (mass transfer, angular-momentum dissipation and energy loss). Some critical remarks on the present situation of transport theories are added. Future developments are outlined. (author)
Nanoscale thermal imaging of dissipation in quantum systems
Halbertal, Dorri; Cuppens, Jo; Shalom, Moshe Ben; Embon, Lior; Shadmi, Nitzan; Anahory, Yonathan; Naren, HR; Sarkar, Jayanta; Uri, Aviram; Ronen, Yuval; Myasoedov, Yury; Levitov, Leonid; Joselevich, Ernesto; Geim, Andre Konstantin; Zeldov, Eli
2016-01-01
Energy dissipation is a fundamental process governing the dynamics of physical, chemical and biological systems. It is also one of the main characteristics that distinguish quantum from classical phenomena. In particular, in condensed matter physics, scattering mechanisms, loss of quantum information or breakdown of topological protection are deeply rooted in the intricate details of how and where the dissipation occurs. Yet the microscopic behaviour of a system is usually not formulated in t...
Relativistic electrodynamics of dissipative elastic media
International Nuclear Information System (INIS)
Kranys, M.
1980-01-01
A phenomenological general relativistic electrodynamics is proposed for a dissipative elastic solid which is polarizable and magnetizable and whose governing equations form a hyperbolic system. Non-stationary transport equations are proposed for dissipative fluxes (and constitutive equations of electrodynamics) containing new cross-effect terms, as required for compatibility with an entropy principle expressed by a new balance equation (including a new Gibbs equation). The dynamic equations are deduced from the unified Minkowski-Abraham-Eckart energy-momentum tensor. The theory, formed by a set of 29 (reducible to 23) partial differential equations (in special relativity) governing the material behaviour of the system characterized by generalizing the constitutive equations of quasineutral media, together with Maxwell's equations, may be referred to as the electrodynamics of dissipative elastic media (or fluid). The proposed transport laws for polarization and magnetization generalize the well-known Debye law for relaxation and show the influence of shear and bulk viscosity on polarization and magentization. Besides the form of the entropy function, the free energy function in the non-stationary regime is also formulated. (auth)
Directory of Open Access Journals (Sweden)
Miroslav Golub
2007-12-01
Full Text Available According to European Strategy for sustainable, competitive and secure energy, which guidelines are described in two documents: ‘’Green Paper: a European Strategy for Sustainable, Competitive and Secure Energy’’ and ‘’White Paper: Energy for the Future: Renewable Sources of Energy’’, it is predicted that share of renewable energy resources in total energy balance will raise from present 6% up to 15% until 2015. Croatia, as candidate country for EU admittance, with growing dependency upon imported energy because of continuous depletion of own energy resources, prior oil and gas, needs to follow EU strategic aims to achieve diversification of energy sources and implement and promote renewable energy resources. This paper presents strategy of geothermal resources development in Republic of Croatia for the period of 2007-2030 in cascade and cogeneration principle of energy utilization. These projections of geothermal energy development are part of comprehensive Strategy of Mineral Resources Development which is made by Faculty of Mining, Geology and Petroleum Engineering for Ministry of Economy, Labour and Entrepreneurship.
Diurnal modulation signal from dissipative hidden sector dark matter
Directory of Open Access Journals (Sweden)
R. Foot
2015-09-01
Full Text Available We consider a simple generic dissipative dark matter model: a hidden sector featuring two dark matter particles charged under an unbroken U(1′ interaction. Previous work has shown that such a model has the potential to explain dark matter phenomena on both large and small scales. In this framework, the dark matter halo in spiral galaxies features nontrivial dynamics, with the halo energy loss due to dissipative interactions balanced by a heat source. Ordinary supernovae can potentially supply this heat provided kinetic mixing interaction exists with strength ϵ∼10−9. This type of kinetically mixed dark matter can be probed in direct detection experiments. Importantly, this self-interacting dark matter can be captured within the Earth and shield a dark matter detector from the halo wind, giving rise to a diurnal modulation effect. We estimate the size of this effect for detectors located in the Southern hemisphere, and find that the modulation is large (≳10% for a wide range of parameters.
Cascades and Dissipative Anomalies in Compressible Fluid Turbulence
Eyink, Gregory L.; Drivas, Theodore D.
2018-02-01
We investigate dissipative anomalies in a turbulent fluid governed by the compressible Navier-Stokes equation. We follow an exact approach pioneered by Onsager, which we explain as a nonperturbative application of the principle of renormalization-group invariance. In the limit of high Reynolds and Péclet numbers, the flow realizations are found to be described as distributional or "coarse-grained" solutions of the compressible Euler equations, with standard conservation laws broken by turbulent anomalies. The anomalous dissipation of kinetic energy is shown to be due not only to local cascade but also to a distinct mechanism called pressure-work defect. Irreversible heating in stationary, planar shocks with an ideal-gas equation of state exemplifies the second mechanism. Entropy conservation anomalies are also found to occur via two mechanisms: an anomalous input of negative entropy (negentropy) by pressure work and a cascade of negentropy to small scales. We derive "4 /5 th-law"-type expressions for the anomalies, which allow us to characterize the singularities (structure-function scaling exponents) required to sustain the cascades. We compare our approach with alternative theories and empirical evidence. It is argued that the "Big Power Law in the Sky" observed in electron density scintillations in the interstellar medium is a manifestation of a forward negentropy cascade or an inverse cascade of usual thermodynamic entropy.
Cascades and Dissipative Anomalies in Compressible Fluid Turbulence
Directory of Open Access Journals (Sweden)
Gregory L. Eyink
2018-02-01
Full Text Available We investigate dissipative anomalies in a turbulent fluid governed by the compressible Navier-Stokes equation. We follow an exact approach pioneered by Onsager, which we explain as a nonperturbative application of the principle of renormalization-group invariance. In the limit of high Reynolds and Péclet numbers, the flow realizations are found to be described as distributional or “coarse-grained” solutions of the compressible Euler equations, with standard conservation laws broken by turbulent anomalies. The anomalous dissipation of kinetic energy is shown to be due not only to local cascade but also to a distinct mechanism called pressure-work defect. Irreversible heating in stationary, planar shocks with an ideal-gas equation of state exemplifies the second mechanism. Entropy conservation anomalies are also found to occur via two mechanisms: an anomalous input of negative entropy (negentropy by pressure work and a cascade of negentropy to small scales. We derive “4/5th-law”-type expressions for the anomalies, which allow us to characterize the singularities (structure-function scaling exponents required to sustain the cascades. We compare our approach with alternative theories and empirical evidence. It is argued that the “Big Power Law in the Sky” observed in electron density scintillations in the interstellar medium is a manifestation of a forward negentropy cascade or an inverse cascade of usual thermodynamic entropy.
Non-dissipative effects in nonequilibrium systems
Maes, Christian
2018-01-01
This book introduces and discusses both the fundamental aspects and the measurability of applications of time-symmetric kinetic quantities, outlining the features that constitute the non-dissipative branch of non-equilibrium physics. These specific features of non-equilibrium dynamics have largely been ignored in standard statistical mechanics texts. This introductory-level book offers novel material that does not take the traditional line of extending standard thermodynamics to the irreversible domain. It shows that although stationary dissipation is essentially equivalent with steady non-equilibrium and ubiquitous in complex phenomena, non-equilibrium is not determined solely by the time-antisymmetric sector of energy-entropy considerations. While this should not be very surprising, this book provides timely, simple reminders of the role of time-symmetric and kinetic aspects in the construction of non-equilibrium statistical mechanics.
Mode-locking via dissipative Faraday instability.
Tarasov, Nikita; Perego, Auro M; Churkin, Dmitry V; Staliunas, Kestutis; Turitsyn, Sergei K
2016-08-09
Emergence of coherent structures and patterns at the nonlinear stage of modulation instability of a uniform state is an inherent feature of many biological, physical and engineering systems. There are several well-studied classical modulation instabilities, such as Benjamin-Feir, Turing and Faraday instability, which play a critical role in the self-organization of energy and matter in non-equilibrium physical, chemical and biological systems. Here we experimentally demonstrate the dissipative Faraday instability induced by spatially periodic zig-zag modulation of a dissipative parameter of the system-spectrally dependent losses-achieving generation of temporal patterns and high-harmonic mode-locking in a fibre laser. We demonstrate features of this instability that distinguish it from both the Benjamin-Feir and the purely dispersive Faraday instability. Our results open the possibilities for new designs of mode-locked lasers and can be extended to other fields of physics and engineering.
On the Lagrangian description of dissipative systems
Martínez-Pérez, N. E.; Ramírez, C.
2018-03-01
We consider the Lagrangian formulation with duplicated variables of dissipative mechanical systems. The application of Noether theorem leads to physical observable quantities which are not conserved, like energy and angular momentum, and conserved quantities, like the Hamiltonian, that generate symmetry transformations and do not correspond to observables. We show that there are simple relations among the equations satisfied by these two types of quantities. In the case of the damped harmonic oscillator, from the quantities obtained by the Noether theorem follows the algebra of Feshbach and Tikochinsky. Furthermore, if we consider the whole dynamics, the degrees of freedom separate into a physical and an unphysical sector. We analyze several cases, with linear and nonlinear dissipative forces; the physical consistency of the solutions is ensured, observing that the unphysical sector has always the trivial solution.
González, Wilma; Altieri, Pablo I; Alvarado, Enrique; Banchs, Héctor L; Colón, Edgar; Escobales, Nelson; Crespo, María
2015-01-01
Higher doses and consumption of energy drinks leads to cardiovascular effects and potential consequences. Principal components found in energy drinks such as caffeine, guarana and taurine has been related to dilatation, aneurysm formation, dissection and ruptures. There is no evidence showing an integration of these components and its effects in endothelium and aortic walls due to higher levels of pressure during exercises. We report a case of a 44 years male with celiac trunk and branches dissection due to long-term consumption of energy drinks and intense exercise routine. Our proposition relates cell and vessel walls alterations including elasticity in endothelial wall due to higher blood pressure, resistance by intense exercise routine and long-term consumption of energy drinks.
Dissipative Effect and Tunneling Time
Directory of Open Access Journals (Sweden)
Samyadeb Bhattacharya
2011-01-01
Full Text Available The quantum Langevin equation has been studied for dissipative system using the approach of Ford et al. Here, we have considered the inverted harmonic oscillator potential and calculated the effect of dissipation on tunneling time, group delay, and the self-interference term. A critical value of the friction coefficient has been determined for which the self-interference term vanishes. This approach sheds new light on understanding the ion transport at nanoscale.
Dissipative Strong-Field Electrodynamics
Gruzinov, Andrei
2007-01-01
A dissipative Lorentz-covariant Ohm's law which uses only the electromagnetic degrees of freedom is proposed. For large conductivity, Maxwell equations equipped with this Ohm's law reduce to the equations of Force-Free Electrodynamics (FFE) with small dissipative corrections, but only in the regions where the ideal FFE 4-current is space-like. This might indicate that the pulsar emission comes primarily from the magnetic separartrix.
Log-Normal Turbulence Dissipation in Global Ocean Models
Pearson, Brodie; Fox-Kemper, Baylor
2018-03-01
Data from turbulent numerical simulations of the global ocean demonstrate that the dissipation of kinetic energy obeys a nearly log-normal distribution even at large horizontal scales O (10 km ) . As the horizontal scales of resolved turbulence are larger than the ocean is deep, the Kolmogorov-Yaglom theory for intermittency in 3D homogeneous, isotropic turbulence cannot apply; instead, the down-scale potential enstrophy cascade of quasigeostrophic turbulence should. Yet, energy dissipation obeys approximate log-normality—robustly across depths, seasons, regions, and subgrid schemes. The distribution parameters, skewness and kurtosis, show small systematic departures from log-normality with depth and subgrid friction schemes. Log-normality suggests that a few high-dissipation locations dominate the integrated energy and enstrophy budgets, which should be taken into account when making inferences from simplified models and inferring global energy budgets from sparse observations.
Fast northward energy transfer in the Atlantic due to Agulhas Rings
van Sebille, Erik; van Leeuwen, P.J.
2007-01-01
The adiabatic transit time of wave energy radiated by an Agulhas ring released in the South Atlantic Ocean to the North Atlantic Ocean is investigated in a two-layer ocean model. Of particular interest is the arrival time of baroclinic energy in the northern part of the Atlantic, because it is
Financial stability at risk due to investing rapidly in renewable energy
Safarzyńska, Karolina; van den Bergh, Jeroen C.J.M.
2017-01-01
We present novel insights about effective energy policies using an agent-based model. The model describes relevant feedback mechanisms between technological evolution, the interbank market and the electricity sector. Analysis with it shows that energy policies affect interbank connectivity and hence
Transport of energy and momentum due to spatial Landau damping and growth of electrostatic waves
International Nuclear Information System (INIS)
Lacina, J.
1994-01-01
It is shown that Landau damping in space (LDS), occuring for time-periodic electrostatic waves, does not lead to any deposition of energy in plasmas. A steady-state balance and a steady-state transport of energy, momentum and particles take place both for damped and growing waves. Because of the phase interference of coherent free and forced particle oscillations, the oscillatory energy of particles increases in the direction of wave propagation; the time-averaged flow of plasma kinetic energy being constant in space for these waves, the LDS must take place for a Maxwellian plasma in order to compensate for the growth of the particle oscillatory energy in space. (Author)
Energy and linear-momentum dissipation in the fusion reaction of 165Ho + 20Ne at 30 MeV/nucleon
Hilscher, D.; Rossner, H.; Gamp, A.; Jahnke, U.; Cheynis, B.; Chambon, B.; Drain, D.; Pastor, C.; Giorni, A.; Morand, C.; Dauchy, A.; Stassi, P.; Petitt, G.
1987-07-01
Neutron energy spectra were measured at angles between 14° and 159° in coincidence with evaporation residues as a function of linear-momentum transfer in reactions of 165Ho with 600 MeV 20Ne. In addition, angular distributions and absolute cross sections for elastic scattering, fission, and evaporation residues have been measured. The preequilibrium component of the neutron spectra has been parametrized with a hot-moving-source fit. For the highest linear-momentum transfer the forward-to-backward anisotropy in the angular distribution is smallest and the quality of the fit is best. From the temperature and multiplicity of evaporated neutrons the level density parameter of nuclei with A~=180 has been determined to be a=A/(10.5+/-1) MeV-1 at excitation energies of 300 to 400 MeV.
Dissipation range turbulent cascades in plasmas
International Nuclear Information System (INIS)
Terry, P. W.; Almagri, A. F.; Forest, C. B.; Nornberg, M. D.; Rahbarnia, K.; Sarff, J. S.; Fiksel, G.; Hatch, D. R.; Jenko, F.; Prager, S. C.; Ren, Y.
2012-01-01
Dissipation range cascades in plasma turbulence are described and spectra are formulated from the scaled attenuation in wavenumber space of the spectral energy transfer rate. This yields spectra characterized by the product of a power law and exponential fall-off, applicable to all scales. Spectral indices of the power law and exponential fall-off depend on the scaling of the dissipation, the strength of the nonlinearity, and nonlocal effects when dissipation rates of multiple fluctuation fields are different. The theory is used to derive spectra for MHD turbulence with magnetic Prandtl number greater than unity, extending previous work. The theory is also applied to generic plasma turbulence by considering the spectrum from damping with arbitrary wavenumber scaling. The latter is relevant to ion temperature gradient turbulence modeled by gyrokinetics. The spectrum in this case has an exponential component that becomes weaker at small scale, giving a power law asymptotically. Results from the theory are compared to three very different types of turbulence. These include the magnetic plasma turbulence of the Madison Symmetric Torus, the MHD turbulence of liquid metal in the Madison Dynamo Experiment, and gyrokinetic simulation of ion temperature gradient turbulence.
Energy Technology Data Exchange (ETDEWEB)
Pleszkun, A.R.
1979-05-01
Previous work on the energy and labor impacts of energy-consumption policies has included the effect of respending of money saved, but not the capital implications of this respending. Here the capital effects are fully accounted for, and turn out to be negligible for a specified conservation scenario and a specified capital expansion model (..delta..C = kC). The robustness of this conclusion is discussed. The implication is that inclusion of only the respending effect is adequate for calculating energy and labor impacts and provides an accuracy to within +- 1% of the total impacts. Operationally, this result obviates the requirement for detailed and expensive calculations.
Quantum Correlation in Circuit QED Under Various Dissipative Modes
Ying-Hua, Ji; Yong-Mei, Liu
2017-02-01
Dynamical evolutions of quantum correlations in circuit quantum electrodynamics (circuit-QED) are investigated under various dissipative modes. The influences of photon number, coupling strength, detuning and relative phase angle on quantum entanglement and quantum discord are compared as well. The results show that quantum discord may be less robust to decoherence than quantum entanglement since the death and revival also appears. Under certain dissipative mode, the decoherence subspace can be formed in circuit-QED due to the cooperative action of vacuum field. Whether a decoherence subspace can be formed not only depends on the form of quantum system but also relates closely to the dissipative mode of environment. One can manipulate decoherence through manipulating the correlation between environments, but the effect depends on the choice of initial quantum states and dissipative modes. Furthermore, we find that proper relative phase of initial quantum state provides one means of suppressing decoherence.
Analysis of Transient Phenomena Due to a Direct Lightning Strike on a Wind Energy System
Rafael B. Rodrigues; Victor M. F. Mendes; João P. S. Catalão
2012-01-01
This paper is concerned with the protection of wind energy systems against the direct effects of lightning. As wind power generation undergoes rapid growth, lightning damages involving wind turbines have come to be regarded as a serious problem. Nevertheless, very few studies exist yet in Portugal regarding lightning protection of wind energy systems using numerical codes. A new case study is presented in this paper, based on a wind turbine with an interconnecting transformer, for the analysi...
ENERGY-EFFICIENT PASSIVE ANTENNA CODE PULSE MODULATION DUE TO THE REFLECTION OF MICROWAVE SIGNAL
Directory of Open Access Journals (Sweden)
T. A. Ismailov
2015-01-01
Full Text Available The article describes an antenna in a corner reflector with a p-i-n-diodes, integrated with the housing transceiver, which allows not only to provide bidirectional communication with the base station as a result of multipath radio three times, but with minimal energy consumption to provide digitally transmit information on the reflected wave flow of any complexity, which allow to eliminate energy in the transmit path and extend the life of the device.
Dividing by four CO2 releases due to energy: the Negatep scenario
International Nuclear Information System (INIS)
Acket, C.; Bacher, P.
2011-01-01
The Negatep scenario aims at dividing CO 2 releases by 4, which means, more or less, dividing the consumption of fossil energies by the same factor, in order to comply with the French 2005 energy act. After a description of the situation in 2006, of trends, and a recall of the objectives defined by the 'Grenelle de l'Environnement' regarding energy savings and renewable energies, the authors show that reaching such a reduction requires to: decrease to nearly zero oil and gas in the residential and tertiary sectors, reduce significantly the use of oil in the transport sector, reduce significantly the use of fossil fuels in industry, increase massively the share of electricity in the energy mix, maintain the share of nuclear in the electricity generation and, as long as the storage of electricity is not developed, limit the share of intermittent energies to a level compatible with that of gas turbines. The study shows that the proposed measures can fulfill the objectives for 2020 proposed by the 'Grenelle de l'Environnement'
Coronal heating by Alfven waves dissipation in compressible nonuniform media
International Nuclear Information System (INIS)
Malara, Francesco; Primavera, Leonardo; Veltri, Pierluigi
1996-01-01
The possibility to produce small scales and then to efficiently dissipate energy has been studied by Malara et al. [1992b] in the case of MHD disturbances propagating in an weakly dissipative incompressible and inhomogeneous medium, for a strictly 2D geometry. We extend this work to include both compressibility and the third component for vector quantities. Numerical simulations show that, when an Alfven wave propagates in a compressible nonuniform medium, the two dynamical effects responsible for the small scales formation in the incompressible case are still at work: energy pinching and phase-mixing. These effects give rise to the formation of compressible perturbations (fast and slow waves or a static entropy wave). Some of these compressive fluctuations are subject to the steepening of the wave front and become shock waves, which are extremely efficient in dissipating their energy, their dissipation being independent of the Reynolds number. Rough estimates of the typical times the various dynamical processes take to produce small scales show that these times are consistent with those required to dissipate inside the solar corona the energy of Alfven waves of photospheric origin
Directory of Open Access Journals (Sweden)
Weber Gregor
2015-06-01
Full Text Available This article is part of a first year doctoral research regarding the current state of knowledge in environmental sustainability, energy economics and their impact on European enterprises. As the current changes and modifications of the German energy economics system are observed by people all around the globe, the current paper analyzes what has been said until now in the scientific literature on character of the new strategy for energy consumption and production in Germany and its impact on environmental and social sustainability. With the help of two questionnaire-based surveys conducted in 2013 and 2014 through the German DIHK1, German enterprises were surveyed in order to: identify potential differences and similarities between the two periods, identify the effects of the energy transition on companies’ profitability, and analyze these effects and compare the results in terms of potential trend developments. The research findings confirmed that changes in the energy system affect not only the environmental sustainability only, but also the economy, in some cases even independent of the stage in which the changing system of the economy presently is.
Decarbonization of the German energy system due to falling or rising power consumption?
International Nuclear Information System (INIS)
Guminski, Andrej; Roon, Serafin von
2016-01-01
Since the publication of the draft ''Climate Protection Plan 2050'' and the ''Green Paper on Energy Efficiency'', it is clear that the Federal Government is focusing on the electrification of the heat and transport sector in order to increase the share of renewable energies in these sectors. This step is not uncontroversial, and represents a paradigm shift in science and politics, because the reduction of the cross electricity consumption move into the background. It is now necessary to clearly distinguish between the conventional power consumption, which must continue to be tested for energy savings and efficiency potential, and the new power consumption, here referred to as the coupling current, which is accepted in order to achieve the objectives of the energy transition. Since the consideration of the energy transition as a purely national project is too short, possible positive and negative effects of the European Union Emission Trading System (EU ETS) deserve particular attention with regard to this reorientation. [de
Analysis of savings due to multiple energy retrofits in a large office building
Energy Technology Data Exchange (ETDEWEB)
McLain, H.A.; Leigh, S.B.; MacDonald, J.M.
1994-05-01
The objective of this analysis was to characterize the benefits of the individual energy conservation measures that were applied to an existing large office building. The measures included those for lighting; those for the heating, ventilation, and air conditioning (HVAC) systems; and an energy management and control system (EMCS). The purpose was to improve our understanding of the impacts of the individual measures in contrast to the entire group of measures that were installed during a building improvement project. The scope of the study was primarily analytical; it used an hourly building simulation model to estimate the benefits. Input parameters for this model were adjusted so that the calculated results matched closely with the available monthly electrical billing data. Supplemental building energy use data were collected and used to improve the adjustment of these parameters. The benefits of the individual measures were then calculated using the matched model.
Dissipative motion perturbation theory and exact solutions
International Nuclear Information System (INIS)
Lodder, J.J.
1976-06-01
Dissipative motion of classical and quantum systems is described. In particular, attention is paid to systems coupled to the radiation field. A dissipative equation of motion for a particle in an arbitrary potential coupled to the radiation field is derived by means of perturbation theory. The usual divrgencies associated with the radiation field are eliminated by the application of a theory of generalized functions. This theory is developed as a subject in its own right and is presented independently. The introduction of classical zero-point energy makes the classical equa tion of motion for the phase density formally the same as its quantum counterpart. In particular, it is shown that the classical zero-point energy prevents the collapse of a classical H-atom and gives rise to a classical ground state. For systems with a quadratic Hamiltoian, the equation of motion can be solved exactly, even in the continuum limit for the radiation field, by means of the new generalized functions. Classically, the Fokker-Planck equation is found without any approximations, and quantum mechanically, the only approximation is the neglect of the change in the ground state caused by the interaction. The derivation is valid even for strong damping and arbitrarily short times. There is no transient time. For harmonic oscillators complete equivalence is shown to exist between quantum mechanics and classical mechanics with zero-point energy. A discussion of the derivation of the Pauli equation is given and perturbation theory is compared with the exact derivation. The exactly solvable models are used to calculate the Langevin force of the radiation field. The result is that the classical Langevin force is exactly delta-correlated, while the quantum Langevin force is not delta-correlated at all. The fluctuation-dissipation theorem is shown to be an exact consequence of the solution to the equations of motion
Energy Technology Data Exchange (ETDEWEB)
Castro Felix, Jaime
2004-02-15
With the aid of the theory behind seismically isolated structures and the bi-linear behavior of an isolated system of Multiple Degrees of Freedom (MDOF), the information obtained on the spectral analysis is complemented with the purpose of simulating one itself for the design of a dissipator of seismic energy. The seismicity in the world is briefly explained, (in Mexico in special for the Geothermal Field of Cerro Prieto), the types of earthquakes, etc., to give way to a documentation of the state-of-the-art in advanced seismic resistant systems and to a procedure to establish the level of seismic qualification of electrical equipment from the level of seismic performance for the Mexican Republic. [Spanish] Con la ayuda de la teoria detras de estructuras aisladas sismicamente y el comportamiento bilineal de un sistema de aislamiento de Multiples Grados de Libertad (MDOF), se complementa la informacion recabada sobre el analisis espectral con el fin de simular uno propio para el diseno de un disipador de energia sismica. Se explica brevemente la sismicidad en el mundo, en Mexico, en especial el Campo Geotermico de Cerro Prieto, los tipos de sismos, etc., para dar paso a una documentacion del estado del arte en sistemas sismorresistentes avanzados y a un procedimiento para establecer el nivel de calificacion sismica de equipos electricos a partir del Nivel de desempeno sismico para la Republica Mexicana.
Dissipative systems in a non-dissipative framework
Das, Umapada; Saha, Aparna; Ghosh, Subrata; Talukdar, Benoy
2013-06-01
Dissipative systems do not have a natural space in the variational formulation of mechanics. We introduce a change of variables such that in the transformed frame the dissipative Newtonian equations mimic those for conservative systems. We present solutions of (a) a linearly damped harmonic oscillator, (b) the corresponding quadratically damped system, (c) a modified Emden-type equation and (d) a generalized Emden equation using their first integrals and deal with the corresponding inverse variational problem to derive Lagrangian and Hamiltonian representations. We confirm that, as opposed to the original damped equations, the reduced equations can be solved by the use of Hamilton-Jacobi theory.
energy and economic losses due to constant power outages in nigeria
African Journals Online (AJOL)
2012-07-02
Jul 2, 2012 ... of Nigeria (PHCN) formerly called National Electric. Power Authority (NEPA) has been incapable of pro- ... amount of electric energy output in kWh. This is commonly called a heat rate in Btu/kWh. Heat rate therefore, is .... Hence, to drive home the point, in order to obtain the useful information and data re-.
Dosimetry in thyroid follicles due to low-energy electrons of iodine using the Monte Carlo method
Energy Technology Data Exchange (ETDEWEB)
Campos, Laelia; Silva, Frank da [Universidade Federal Rural de Pernambuco (UFRPE), Recife, PE (Brazil). Dept. of Statistics and Information Technology]. E-mail: lpbcampos@gmail.com; l.campos@deinfo.ufrpe.br
2008-11-15
Objective: To evaluate the absorbed dose in thyroid follicles due to low-energy electrons such as Auger and internal conversion electrons, besides beta particles, for iodine radioisotopes ({sup 131}I, {sup 132}I, {sup 13}'3I, {sup 134}I and {sup 135}I) utilizing the Monte Carlo method. Materials And Methods: The dose calculation was performed at follicular level, simulating Auger, internal conversion electrons and beta particles, with the MCNP4C code. The follicles (colloid and follicular cells) were modeled as spheres with colloid diameter ranging from 30 to 500 {mu}m, and with the same density of water (1.0 g.cm{sup -3}). Results: Considering low-energy particles, the contribution of {sup 131}I for total absorbed dose to the colloid is about 25%, while the contribution due to short-lived isotopes is 75%. For follicular cells, this contribution is still higher achieving 87% due to short-lived iodine and 13% due to {sup 131}I. Conclusion: The results of the present study demonstrate the importance of considering low energy particles in the contribution for the total absorbed dose at follicular level (colloid and follicular cells) due to iodine radioisotopes ({sup 13}'1I, {sup 13}'2I, {sup 1}'3'3I, {sup 1}'3{sup 4}I and {sup 135}I). (author)
Energy efficient measures to reduce PM2,5 emissions due to cooking
Jacobs, P.; Cornelissen, H.J.M.; Borsboom, W.A.
2016-01-01
Laboratory tests with heating olive oil in kitchens suggest that the current building regulation in the Netherlands for kitchen exhaust is inadequate to directly address cooking fumes. Due to building traditions, for motor less cooker hoods often only 50% of the available capacity of the mechanical
Dissipative Properties of EHD Lubricant Film
Fedorov, S. V.
2018-01-01
For the case of the failure of the lubricant film at hydrodynamic lubrication a common thermodynamic theory of strength is considered. According to this theory the failure occurs when the internal energy density (potential and thermal components) in the volume of material reaches a constant for a given material. A special case of this theory is considered when only the density of heat (kinetic) component of internal energy is taken into account. Temperature condition determines the limit state for liquid lubricants - mineral oils. When analyzing the regularities of friction at EHD lubrication the state and properties of the oil film at the condition of irregular and hydrostatic compression. The original structural model of oil film at EHD lubrication in the form of the rotary oscillating cells with elastic interactions to each other is proposed. It is similar to the Rayleigh-Benard cells and corresponds to the cellular hypothesis of J. Gibbs for the case of equilibrium and reversible process. It is quite possible that the size of the cells have an order of about nano level. The oil film dissipates energy in the direction of relative motion of bodies. This oil film has the highest dissipative properties.
The TKE dissipation rate in the northern South China Sea
Lozovatsky, Iossif; Liu, Zhiyu; Fernando, Harindra Joseph S.; Hu, Jianyu; Wei, Hao
2013-12-01
The microstructure measurements taken during the summer seasons of 2009 and 2010 in the northern South China Sea (between 18°N and 22.5°N, and from the Luzon Strait to the eastern shelf of China) were used to estimate the averaged dissipation rate in the upper pycnocline of the deep basin and on the shelf. Linear correlation between and the estimates of available potential energy of internal waves, which was found for this data set, indicates an impact of energetic internal waves on spatial structure and temporal variability of . On the shelf stations, the bottom boundary layer depth-integrated dissipation reaches 17-19 mW/m2, dominating the dissipation in the water column below the surface layer. In the pycnocline, the integrated dissipation was mostly ˜10-30 % of . A weak dependence of bin-averaged dissipation on the Richardson number was noted, according to , where ɛ 0 + ɛ m is the background value of for weak stratification and Ri cr = 0.25, pointing to the combined effects of shear instability of small-scale motions and the influence of larger-scale low frequency internal waves. The latter broadly agrees with the MacKinnon-Gregg scaling for internal-wave-induced turbulence dissipation.
Fluctuation-dissipation relation in accelerated frames
Adhikari, Ananya; Bhattacharya, Krishnakanta; Chowdhury, Chandramouli; Majhi, Bibhas Ranjan
2018-02-01
A uniformly accelerated (Rindler) observer will detect particles in the Minkowski vacuum, known as the Unruh effect. The spectrum is thermal and the temperature is given by that of the Killing horizon, which is proportional to the acceleration. Considering that these particles are kept in a thermal bath with this temperature, we find that the correlation function of the random force due to radiation acting on the particles, as measured by the accelerated frame, shows the fluctuation-dissipation relation. It is observed that the correlations, in both (1 +1 ) spacetime and (1 +3 ) dimensional spacetimes, are of the Brownian type. We discuss the implications of this new observation.
Reaction time in the 19F+93Nb dissipative collision
International Nuclear Information System (INIS)
Tian Wendong; Wang Qi; Li Songlin; Dong Yuchuan; Guo Zhongyan; Zhan Wenlong; Xiao Guoqing
2002-01-01
The angular distribution and excitation function of the dissipative products have been measured in the reaction 19 F + 93 Nb. The reaction time of the dissipative products is extracted from the angular distribution and compared with that extracted from their energy auto-correlation function. A great difference exists between the reaction times extracted from these two methods. The results obtained from analyzing these two methods in different symmetrical reaction systems show that the reaction time extracted in the more symmetrical system by analyzing the slope of the angular distribution demonstrates the characteristic times of both direct and dissipative products, while the reaction times extracted in the more asymmetrical system only reflects the character of the direct products. But the method of the energy auto-correlation function can give the the characteristic time for dissipative products in both symmetrical and asymmetrical system. In addition, the damping rotation feature of the dinuclear system formed in the dissipative reaction can be described by analyzing the energy auto-correlation function
Power injected in dissipative systems and the fluctuation theorem
Aumaître, S.; Fauve, S.; McNamara, S.; Poggi, P.
We consider three examples of dissipative dynamical systems involving many degrees of freedom, driven far from equilibrium by a constant or time dependent forcing. We study the statistical properties of the injected and dissipated power as well as the fluctuations of the total energy of these systems. The three systems under consideration are: a shell model of turbulence, a gas of hard spheres colliding inelastically and excited by a vibrating piston, and a Burridge-Knopoff spring-block model. Although they involve different types of forcing and dissipation, we show that the statistics of the injected power obey the ``fluctuation theorem" demonstrated in the case of time reversible dissipative systems maintained at constant total energy, or in the case of some stochastic processes. Although this may be only a consequence of the theory of large deviations, this allows a possible definition of ``temperature" for a dissipative system out of equilibrium. We consider how this ``temperature" scales with the energy and the number of degrees of freedom in the different systems under consideration.
Strong tidal dissipation in Io and Jupiter from astrometric observations.
Lainey, Valéry; Arlot, Jean-Eudes; Karatekin, Ozgür; Van Hoolst, Tim
2009-06-18
Io is the volcanically most active body in the Solar System and has a large surface heat flux. The geological activity is thought to be the result of tides raised by Jupiter, but it is not known whether the current tidal heat production is sufficiently high to generate the observed surface heat flow. Io's tidal heat comes from the orbital energy of the Io-Jupiter system (resulting in orbital acceleration), whereas dissipation of energy in Jupiter causes Io's orbital motion to decelerate. Here we report a determination of the tidal dissipation in Io and Jupiter through its effect on the orbital motions of the Galilean moons. Our results show that the rate of internal energy dissipation in Io (k(2)/Q = 0.015 +/- 0.003, where k(2) is the Love number and Q is the quality factor) is in good agreement with the observed surface heat flow, and suggest that Io is close to thermal equilibrium. Dissipation in Jupiter (k(2)/Q = (1.102 +/- 0.203) x 10(-5)) is close to the upper bound of its average value expected from the long-term evolution of the system, and dissipation in extrasolar planets may be higher than presently assumed. The measured secular accelerations indicate that Io is evolving inwards, towards Jupiter, and that the three innermost Galilean moons (Io, Europa and Ganymede) are evolving out of the exact Laplace resonance.
2007 CO2 emissions due to energy combustion in the world
International Nuclear Information System (INIS)
2010-01-01
Worldwide energy combustion contributes to more than 95% of the global CO 2 emissions. According to the last International Energy Agency (IEA) results, these emissions have raised by 3.3% with respect to 2006 and by 38% with respect to 1990 with a total of about 29 Gt of CO 2 . After a new 8% boom in 2007, China's emissions have tripled since 1990 with a total exceeding 6 Gt of CO 2 . China has become the first CO 2 emitter in front of the USA. When compared to the number of inhabitants, China's emissions are comparable to the world average (4.4 t CO 2 /hab) but remain four times lower than the ones of the USA. (J.S.)
Wang, Shaobin; Luo, Kunli
2018-01-01
The relation between life expectancy and energy utilization is of particular concern. Different viewpoints concerned the health impacts of heating policy in China. However, it is still obscure that what kind of heating energy or what pattern of heating methods is the most related with the difference of life expectancies in China. The aim of this paper is to comprehensively investigate the spatial relations between life expectancy at birth (LEB) and different heating energy utilization in China by using spatial autocorrelation models including global spatial autocorrelation, local spatial autocorrelation and hot spot analysis. The results showed that: (1) Most of heating energy exhibit a distinct north-south difference, such as central heating supply, stalks and domestic coal. Whereas spatial distribution of domestic natural gas and electricity exhibited west-east differences. (2) Consumption of central heating, stalks and domestic coal show obvious spatial dependence. Whereas firewood, natural gas and electricity did not show significant spatial autocorrelation. It exhibited an extinct south-north difference of heat supply, stalks and domestic coal which were identified to show significant positive spatial autocorrelation. (3) Central heating, residential boilers and natural gas did not show any significant correlations with LEB. While, the utilization of domestic coal and biomass showed significant negative correlations with LEB, and household electricity shows positive correlations. The utilization of domestic coal in China showed a negative effect on LEB, rather than central heating. To improve the solid fuel stoves and control consumption of domestic coal consumption and other low quality solid fuel is imperative to improve the public health level in China in the future. Copyright © 2017 Elsevier B.V. All rights reserved.
Cowgill, E.; Gold, R. D.; Arrowsmith, R.; Friedrich, A. M.
2015-12-01
In elastic rebound theory, hazard increases as interseismic strain rebuilds after rupture. This model is challenged by the temporal variation in the pacing of major earthquakes that is both predicted by mechanical models and suggested by some long paleoseismic records (e.g., 1-3). However, the extent of such behavior remains unclear due to a lack of long (5-25 ky) records of fault slip. Using Monte Carlo analysis of 11 offset landforms, we determined a 16-ky record of fault slip for the active, left-lateral Altyn Tagh fault, which bounds the NW margin of the Tibetan Plateau. This history reveals a pulse of accelerated slip between 6.4 and 6.0 ka, during which the fault slipped 9 +14/-2 m at a rate of 23 +35/-5 mm/y, or ~3x the 16 ky average of 8.1 +1.2/-0.9mm/y. These two modes of earthquake behavior suggest temporal variation in the rates of stress storage and release. The simplest explanation for the pulse is a cluster of 2-8 Mw > 7.5 earthquakes. Such supercyclicity has been reported for the Sunda (4) and Cascadia (3) megathrusts, but contrasts with steady slip along the strike-slip Alpine fault (5), for example. A second possibility is that the pulse reflects a single, unusually large rupture. However, this Black Swan event is unlikely: empirical scaling relationships require a Mw 8.2 rupture of the entire 1200-km-long ATF to produce 7 m of average slip. Likewise, Coulomb stress change from rupture on the adjacent North Altyn fault is of modest magnitude and overlap with the ATF. Poor temporal correlation between precipitation and the slip pulse argues against climatically modulated changes in surface loading (lakes/ice) or pore-fluid pressure. "Paleoslip" studies such as this sacrifice the single-event resolution of paleoseismology in exchange for long records that quantify both the timing and magnitude of fault slip averaged over multiple ruptures, and are essential for documenting temporal variations in fault slip as we begin to use calibrated physical
Workshop on induced Seismicity due to fluid injection/production from Energy-Related Applications
Energy Technology Data Exchange (ETDEWEB)
Majer, E.L.; Asanuma, Hiroshi; Rueter, Horst; Stump, Brian; Segall, Paul; Zoback, Mark; Nelson, Jim; Frohlich, Cliff; Rutledge, Jim; Gritto, Roland; Baria, Roy; Hickman, Steve; McGarr, Art; Ellsworth, Bill; Lockner, Dave; Oppenheimer, David; Henning, Peter; Rosca, Anca; Hornby, Brian; Wang, Herb; Beeler, Nick; Ghassemi, Ahmad; Walters, Mark; Robertson-Tait, Ann; Dracos, Peter; Fehler, Mike; Abou-Sayed, Ahmed; Ake, Jon; Vorobiev, Oleg; Julian, Bruce
2011-04-01
Geothermal energy, carbon sequestration, and enhanced oil and gas recovery have a clear role in U.S. energy policy, both in securing cost-effective energy and reducing atmospheric CO{sub 2} accumulations. Recent publicity surrounding induced seismicity at several geothermal and oil and gas sites points out the need to develop improved standards and practices to avoid issues that may unduly inhibit or stop the above technologies from fulfilling their full potential. It is critical that policy makers and the general community be assured that EGS, CO{sub 2} sequestration, enhanced oil/gas recovery, and other technologies relying on fluid injections, will be designed to reduce induced seismicity to an acceptable level, and be developed in a safe and cost-effective manner. Induced seismicity is not new - it has occurred as part of many different energy and industrial applications (reservoir impoundment, mining, oil recovery, construction, waste disposal, conventional geothermal). With proper study/research and engineering controls, induced seismicity should eventually allow safe and cost-effective implementation of any of these technologies. In addition, microseismicity is now being used as a remote sensing tool for understanding and measuring the success of injecting fluid into the subsurface in a variety of applications, including the enhancement of formation permeability through fracture creation/reactivation, tracking fluid migration and storage, and physics associated with stress redistribution. This potential problem was envisaged in 2004 following observed seismicity at several EGS sites, a study was implemented by DOE to produce a white paper and a protocol (Majer et al 2008) to help potential investors. Recently, however, there have been a significant number of adverse comments by the press regarding induced seismicity which could adversely affect the development of the energy sector in the USA. Therefore, in order to identify critical technology and research
Increased energy in stable dry-band arcs due to length compression
Zhang, X.; Rowland, S. M.; Terzija, V.
2010-01-01
The occurrence of dry-band arcs on outdoor composite insulators can degrade the polymeric materials' surface and ultimately may lead to insulator failure. The degradation processes are generally considered as aging effects occurring over long periods of time, from years to decades. In this paper, it is shown that if a stable dryband arc is physically compressed in length by external forces, such as electrolyte deformation due to wind or gravity, the arcing activities will become more severe. ...
Tritium in the environment due to the peaceful use of nuclear energy
International Nuclear Information System (INIS)
Mattern, F.C.M.; Regt, H.J.B. de; Aurand, K.; Ruehle, H.
1975-12-01
With values of several μrem/a and more, the present tritium exposure due to nuclear power stations and nuclear research centres in the FRG and the Netherlands is still very low. A theoretical estimation of the radiation exposure due to 100 hypothetical nuclear power stations along the Rhine - each with a power of 1,000 MWe - would give an additional radiation exposure of only about 0.15 mrem if the surface water were used as drinking water. Estimations of the tritium emission for the year 2000 show that the global environmental pollution is also low, having a mean value of about 0.1 mrem/a. The highest future environmental pollution due to tritium is expected from reprocessing plants. To keep tritium emissions with the waste water from reprocessing plants as low as possible, it should be found out whether waste water may, e.g. be pumped into deeper strata of the earth or into the deep sea. (orig.) [de
Huang, Z.; Xu, C.
2014-12-01
In laboratory tests of oscillating-water-column (OWC) devices for extracting wave energy from ocean waves, an orifice is often used as the power-takeoff mechanism. Calculations of the energy loss due to vortex shedding and the pneumatic extraction efficiency of the OWC chamber are two challenging issues. Direct measurement of the energy loss due to vortex shedding is difficult. The pneumatic extraction efficiency is often calculated by using a one-point measurement method, in which one pressure senor is used to measure the air pressure variation and one wave gauge is used to measure the instantaneous surface displacement inside the OWC chamber. This method is simple, but a systematic error may be introduced, especially for shorter waves. Based on our recent laboratory and theoretical studies of a pile-supported OWC device, we present a method for estimating the energy loss due to vortex shedding and improving the accuracy in the calculation of pneumatic extraction efficiency using one-point method. The method in this study is designed for an OWC device whose chamber has a circular cross section, but can be extended to other cases where development of an analytical theory is possible.
Radiation effects and damage formation in semiconductors due to high-energy ion irradiation
Energy Technology Data Exchange (ETDEWEB)
Kamarou, A.
2006-11-07
The object of this thesis was the study of ion-beam induced damage formation and annealing in crystalline and conventionally predamaged Ge, GaAs, and InP. The samples were irradiated either at {approx}80 K or at room temperature with Kr, Xe, or Au ions with specific energy of about 0.3 MeV/u to 3 MeV/u. Thereafter the samples were studied by means of Rutherford backscattering spectroscopy and/or transmission electron microscopy.
Ding, Si-Jing; Li, Xiaoguang; Nan, Fan; Zhong, Yu-Ting; Zhou, Li; Xiao, Xudong; Wang, Qu-Quan; Zhang, Zhenyu
2017-10-01
Recent intense effort has been devoted to exploring different manifestations of resonant excitations of strongly coupled plasmons and excitons, but so far such studies have been limited to situations where the Fano- or Rabi-type spectra are largely symmetric at zero detuning. Using a newly developed full quantum mechanical model, here we reveal the existence of a highly asymmetric spectroscopic regime for both the Rabi splitting and transparency dip. The asymmetric nature is inherently tied to the non-negligible exciton absorbance and is caused by substantial interference-induced energy repartitioning of the resonance peaks. This theoretical framework can be exploited to reveal the quantum behaviors of the two excitation entities with varying mutual coupling strengths in both linear and nonlinear regimes. We also use prototypical systems of rhodamine molecules strongly coupled with AuAg alloyed nanoparticles and well-devised control experiments to demonstrate the validity and tunability of the energy repartitioning and correlated electronic state occupations, as captured by the variations in the asymmetric spectroscopy and corresponding nonlinear absorption coefficient as a function of the Au:Ag ratio. The present study helps to substantially enrich our microscopic understanding of strongly coupled plasmon-exciton systems.
Investigation of reasons for small changes in energy of UCN due to their interaction with surface
Lychagin, E V; Nekhaev, G V; Strelkov, A V; Kartashov, D G; Nesvizhevsky, V V
2002-01-01
The nature of the phenomenon of small changes in energy of ultracold neutrons (UCN) has been investigated. This phenomenon occurs during collisions of UCN with a surface, which increase the UCN energy by approx 10 sup - sup 7 eV with a probability of 10 sup - sup 8 -10 sup - sup 5 per collision. Such neutrons are named VUCN. It was observed that the preliminary warming up of samples at 500-600 K leads to an increase of the small heating probability P sub V sub U sub C sub N by at least a factor of 100 for a surface of stainless steel and by a factor of 10 for a copper surface. Extremely intensive UCN small heating by a diamond nanopowder has been observed for the first time. The spectrum of these VUCN and the temperature dependence of their heating probability P sub V sub U sub C sub N are similar to those measured earlier for stainless steel, beryllium, and copper. It is not observed small UCN heating, nor nanoparticles on a monocrystalline sapphire surface. That leads to the conclusion that VUCN are produce...
Mechanical dissipation at elevated temperatures in tetrahedral amorphous carbon.
Energy Technology Data Exchange (ETDEWEB)
Sullivan, John P.; Friedmann, Thomas Aquinas; Czaplewski, David A.; Wendt, Joel Robert
2005-05-01
We have measured the temperature dependence of mechanical dissipation in tetrahedral amorphous carbon flexural and torsional resonators over the temperature range from 300 to 1023 K. The mechanical dissipation was found to be controlled by defects within the material, and the magnitude and temperature dependence of the dissipation were found to depend on whether flexural or torsional vibrational modes were excited. The defects that were active under flexural stresses have a relatively flat concentration from 0.4 to 0.7 eV with an ever increasing defect concentration up to 1.9 eV. Under shear stresses (torsion), the defect activation energies increase immediately beginning at 0.4 eV, with increasing defect concentration at higher energies.
Memory effects in dissipative nucleus-nucleus collision
Yadav, H L
2002-01-01
A macroscopic dynamical model within the framework of a multidimensional Fokker-Planck equation is employed for a theoretical description of low-energy dissipative collisions between two heavy nuclei. The effect of two-body collisions leading to intrinsic equilibrium has been treated phenomenologically using the basic concepts of dissipative diabatic dynamics. The heavy-ion reaction sup 8 sup 6 Kr(8.18 MeV/u) + sup 1 sup 6 sup 6 Er has been as a prototype to study and demonstrate the memory effects for dissipation and diffusion processes. Our calculated results for the deflection angle, angular distributions d sigma/d theta sub c sub m , energy distributions d sigma/d DELTA EPSILON, and element distributions d sigma/d ZETA illustrate a remarkable dependence on the memory effects and are consistent with the experimental data
Dissipative effects in Multilevel Systems
Energy Technology Data Exchange (ETDEWEB)
Solomon, A I [Department of Physics and Astronomy, Open University, Milton Keynes MK7 6AA (United Kingdom); Schirmer, S G [Department of Applied Maths and Theoretical Physics, University of Cambridge, Cambridge, CB3 0WA (United Kingdom)
2007-11-15
Dissipation is sometimes regarded as an inevitable and regrettable presence in the real evolution of a quantum system. However, the effects may not always be malign, although often non-intuitive and may even be beneficial. In this note we we display some of these effects for N-level systems, where N = 2,3,4. We start with an elementary introduction to dissipative effects on the Bloch Sphere, and its interior, the Bloch Ball, for a two-level system. We describe explicitly the hamiltonian evolution as well as the purely dissipative dynamics, in the latter case giving the t {yields} {infinity} limits of the motion. This discussion enables us to provide an intuitive feeling for the measures of control-reachable states. For the three-level case we discuss the impossibility of isolating a two-level (qubit) subsystem; this is a Bohm-Aharonov type consequence of dissipation. We finally exemplify the four-level case by giving constraints on the decay of two-qubit entanglement.
Yu, Biying; Wei, Yi-Ming; Kei, Gomi; Matsuoka, Yuzuru
2018-02-01
Population dynamics has been acknowledged as a key concern for projecting future emissions, partly because of the huge uncertainties related to human behaviour. However, the heterogeneous shifts of human behaviour in the process of demographic transition are not well explored when scrutinizing the impacts of population dynamics on carbon emissions. Here, we expand the existing population-economy-environment analytical structure to address the above limitations by representing the trend of demographic transitions to small-family and ageing society. We specifically accommodate for inter- and intra-life-stage variations in time allocation and consumption in the population rather than assuming a representative household, and take a less developed province, Sichuan, in China as the empirical context. Our results show that the demographic shift to small and ageing households will boost energy consumption and carbon emissions, driven by the joint variations in time-use and consumption patterns. Furthermore, biased pictures of changing emissions will emerge if the time effect is disregarded.
International Nuclear Information System (INIS)
Gardner, John; Skumatz, Lisa A.
2005-01-01
This paper summarizes recent work using statistical methods to examine the portions of the apparent price differences for a variety of appliances that are attributable to efficiency labels or components of efficient measures. The work stems from research examining progress in market transformation. The goal was to monitor market progress in the premium associated with efficient equipment compared to standard equipment - and potentially track these changes (hopefully, according to logic, declining) over time. However, the incremental cost metric is always confounded by the fact that the 'feature bundle' on appliances and lighting is not consistent ( i.e. , many efficient products are loaded up with other, high-end features). Based on work conducted by the authors some years ago, we adapted statistical models to decompose the price differentials for efficient and standard refrigerators, clothes washers, and dish washers. The authors used site visits and web searches to gather data on appliance prices and features for a set of efficient and standard models. The authors first examined apparent (raw) price differentials between efficient and standard models. Then, using regression techniques to control for differences in features on the measures, the differences attributable to various features - and in particular to energy efficient features and logos - were estimated. The results showed that while the apparent (gross) price differences for efficient measures are high, the percentage and dollar differences decrease dramatically when the price differences statistically attributable to other features of the measure are accounted for. The work illustrates a promising approach for three important applications in program planning and evaluation: tracking market progress within and between states or service territories, using a proxy variable that is less expensive and complicated to measure than direct indicators of sales or market share, identifying appropriate levels for
Energy dissipation and clustering in granular streams
Waitukaitis, Scott; Royer, John; Gruetjen, Helge; Jaeger, Heinrich
2009-11-01
The presence of weak cohesive forces between macroscopic grains can lead to the break up of a free falling granular stream, similar to the surface-tension-driven break up of a liquid streamfootnotetext Royer, J. R. et al. Nature 459 1110 - 1113 (2009).. This sensitivity to minute forces suggests that these free falling streams could serve as a tool to probe the interactions between grains. In order to investigate the connection between the stream dynamics and the grain-grain interactions, we perform molecular dynamics simulations of a granular stream freely falling out of a hopper varying the cohesion and inelasticity of the grains. We find that in the absence of cohesive forces the stream breaks apart into isolated grains, in contrast to the clustering observed in simulations of inelastic granular gases. For sufficiently high cohesive forces we reproduce the break up of stream into droplets, while with lower cohesive forces the stream breaks up into smaller clusters consisting of only a few grains. Measuring the change in contact number and decay of velocity fluctuations with depth, we characterize the different regions of the force-inelasticity phase space.
Tidal dissipation in rotating fluid bodies: the presence of a magnetic field
Lin, Yufeng; Ogilvie, Gordon I.
2018-02-01
We investigate effects of the presence of a magnetic field on tidal dissipation in rotating fluid bodies. We consider a simplified model consisting of a rigid core and a fluid envelope, permeated by a background magnetic field (either a dipolar field or a uniform axial field). The wave-like tidal responses in the fluid layer are in the form of magnetic Coriolis waves, which are restored by both the Coriolis force and the Lorentz force. Energy dissipation occurs through viscous damping and Ohmic damping of these waves. Our numerical results show that the tidal dissipation can be dominated by Ohmic damping even with a weak magnetic field. The presence of a magnetic field smooths out the complicated frequency dependence of the dissipation rate, and broadens the frequency spectrum of the dissipation rate, depending on the strength of the background magnetic field. However, the frequency-averaged dissipation is independent of the strength and structure of the magnetic field, and of the dissipative parameters in the approximation that the wave-like response is driven only by the Coriolis force acting on the non-wavelike tidal flow. Indeed, the frequency-averaged dissipation quantity is in good agreement with previous analytical results in the absence of magnetic fields. Our results suggest that the frequency-averaged tidal dissipation of the wave-like perturbations is insensitive to detailed damping mechanisms and dissipative properties.
Compaction shock dissipation in low density granular explosive
Energy Technology Data Exchange (ETDEWEB)
Rao, Pratap T.; Gonthier, Keith A., E-mail: gonthier@me.lsu.edu; Chakravarthy, Sunada [Mechanical and Industrial Engineering Department, Louisiana State University, Baton Rouge, Louisiana 70803 (United States)
2016-06-14
The microstructure of granular explosives can affect dissipative heating within compaction shocks that can trigger combustion and initiate detonation. Because initiation occurs over distances that are much larger than the mean particle size, homogenized (macroscale) theories are often used to describe local thermodynamic states within and behind shocks that are regarded as the average manifestation of thermodynamic fields at the particle scale. In this paper, mesoscale modeling and simulation are used to examine how the initial packing density of granular HMX (C{sub 4}H{sub 8}N{sub 8}O{sub 8}) C{sub 4}H{sub 8}N{sub 8}O{sub 8} having a narrow particle size distribution influences dissipation within resolved, planar compaction shocks. The model tracks the evolution of thermomechanical fields within large ensembles of particles due to pore collapse. Effective shock profiles, obtained by averaging mesoscale fields over space and time, are compared with those given by an independent macroscale compaction theory that predicts the variation in effective thermomechanical fields within shocks due to an imbalance between the solid pressure and a configurational stress. Reducing packing density is shown to reduce the dissipation rate within shocks but increase the integrated dissipated work over shock rise times, which is indicative of enhanced sensitivity. In all cases, dissipated work is related to shock pressure by a density-dependent power law, and shock rise time is related to pressure by a power law having an exponent of negative one.
Compaction shock dissipation in low density granular explosive
Rao, Pratap T.; Gonthier, Keith A.; Chakravarthy, Sunada
2016-06-01
The microstructure of granular explosives can affect dissipative heating within compaction shocks that can trigger combustion and initiate detonation. Because initiation occurs over distances that are much larger than the mean particle size, homogenized (macroscale) theories are often used to describe local thermodynamic states within and behind shocks that are regarded as the average manifestation of thermodynamic fields at the particle scale. In this paper, mesoscale modeling and simulation are used to examine how the initial packing density of granular HMX (C4H8N8O8) C4H8N8O8 having a narrow particle size distribution influences dissipation within resolved, planar compaction shocks. The model tracks the evolution of thermomechanical fields within large ensembles of particles due to pore collapse. Effective shock profiles, obtained by averaging mesoscale fields over space and time, are compared with those given by an independent macroscale compaction theory that predicts the variation in effective thermomechanical fields within shocks due to an imbalance between the solid pressure and a configurational stress. Reducing packing density is shown to reduce the dissipation rate within shocks but increase the integrated dissipated work over shock rise times, which is indicative of enhanced sensitivity. In all cases, dissipated work is related to shock pressure by a density-dependent power law, and shock rise time is related to pressure by a power law having an exponent of negative one.
Observation-based input and dissipation version of WAVEWATCH III
Zieger, Stefan; Babanin, Alexander; Rogers, Erick; Young, Ian
2013-04-01
Measurements collected at Lake George, Australia, resulted in new insights on the processes of wind wave interaction and white-capping dissipation and consequently new parameterisations of these source terms. The new nonlinear wind input source term accounts for dependence of the growth increment on wave steepness, for airflow separation which leads to a relative reduction of the growth under extreme wind conditions, and for negative growth rate under adverse winds. The new wave breaking and whitecapping dissipation source function features two separate terms: the inherent breaking term and a cumulative dissipation term due to influences of longer waves on wave breaking of shorter waves. Another novel feature of this dissipation is the threshold in terms of spectral density: below this threshold breaking stops and whitecapping becomes zero. In such conditions dissipation due to wave interaction with water turbulence takes over, which regime is particularly relevant for decaying seas and for swell. This paper describes these source terms implemented in WAVEWATCH III and evaluates the performance against existing source terms in duration-limited simulations and against buoy measurements for windsea-dominated conditions. Results show agreement by means of growth curves and integral parameters in the simulations and hindcast. The paper also introduces wave breaking probability as model output, along with standard wind-wave metrics.
Contaminant-State Broadening Mechanism in a Driven Dissipative Rydberg System
Porto, J. V.
2017-04-01
The strong interactions in Rydberg atoms make them an ideal system for the study of correlated many-body physics, both in the presence and absence of dissipation. Using such highly excited atomic states requires addressing challenges posed by the dense spectrum of Rydberg levels, the detrimental effects of spontaneous emission, and strong interactions. A full understanding of the scope and limitations of many Rydberg-based proposals requires simultaneously including these effects, which typically cannot be described by a mean-field treatment due to correlations in the quantum coherent and dissipative processes. We study a driven, dissipative system of Rydberg atoms in a 3D optical lattice, and observe substantial deviation from single-particle excitation rates, both on and off resonance. The observed broadened spectra cannot be explained by van der Waals interactions or a mean-field treatment of the system. Based on the magnitude of the broadening and the scaling with density and two-photon Rabi frequency, we attribute these effects to unavoidable blackbody-induced transitions to nearby Rydberg states of opposite parity, which have large, resonant dipole-dipole interactions with the state of interest. Even at low densities of Rydberg atoms, uncontrolled production of atoms in other states significantly modifies the energy levels of the remaining atoms. These off-diagonal exchange interactions result in complex many-body states of the system and have implications for off-resonant Rydberg dressing proposals. This work was partially supported by the ARL-CDQI program.
de Carvalho, Alberito Rodrigo; Andrade, Alexandro; Peyré-Tartaruga, Leonardo Alexandre
2015-01-01
One goal of the locomotion is to move the body in the space at the most economical way possible. However, little is known about the mechanical and energetic aspects of locomotion that are affected by low back pain. And in case of occurring some damage, little is known about how the mechanical and energetic characteristics of the locomotion are manifested in functional activities, especially with respect to the energy-minimizer mechanisms during locomotion. This study aimed: a) to describe the main energy-minimizer mechanisms of locomotion; b) to check if there are signs of damage on the mechanical and energetic characteristics of the locomotion due to chronic low back pain (CLBP) which may endanger the energy-minimizer mechanisms. This study is characterized as a narrative literature review. The main theory that explains the minimization of energy expenditure during the locomotion is the inverted pendulum mechanism, by which the energy-minimizer mechanism converts kinetic energy into potential energy of the center of mass and vice-versa during the step. This mechanism is strongly influenced by spatio-temporal gait (locomotion) parameters such as step length and preferred walking speed, which, in turn, may be severely altered in patients with chronic low back pain. However, much remains to be understood about the effects of chronic low back pain on the individual's ability to practice an economic locomotion, because functional impairment may compromise the mechanical and energetic characteristics of this type of gait, making it more costly. Thus, there are indications that such changes may compromise the functional energy-minimizer mechanisms. Copyright © 2014 Elsevier Editora Ltda. All rights reserved.
Temperature dependent surface modification of molybdenum due to low energy He+ ion irradiation
International Nuclear Information System (INIS)
Tripathi, J.K.; Novakowski, T.J.; Joseph, G.; Linke, J.; Hassanein, A.
2015-01-01
In this paper, we report on the temperature dependent surface modifications in molybdenum (Mo) samples due to 100 eV He + ion irradiation in extreme conditions as a potential candidate to plasma-facing components in fusion devices alternative to tungsten. The Mo samples were irradiated at normal incidence, using an ion fluence of 2.6 × 10 24 ions m −2 (with a flux of 7.2 × 10 20 ions m −2 s −1 ). Surface modifications have been studied using high-resolution field emission scanning electron-(SEM) and atomic force (AFM) microscopy. At 773 K target temperature homogeneous evolution of molybdenum nanograins on the entire Mo surface were observed. However, at 823 K target temperature appearance of nano-pores and pin-holes nearby the grain boundaries, and Mo fuzz in patches were observed. The fuzz density increases significantly with target temperatures and continued until 973 K. However, at target temperatures beyond 973 K, counterintuitively, a sequential reduction in the fuzz density has been seen till 1073 K temperatures. At 1173 K and above temperatures, only molybdenum nano structures were observed. Our temperature dependent studies confirm a clear temperature widow, 823–1073 K, for Mo fuzz formation. Ex-situ high resolution X-ray photoelectron spectroscopy studies on Mo fuzzy samples show the evidence of MoO 3 3d doublets. This elucidates that almost all the Mo fuzz were oxidized during open air exposure and are thick enough as well. Likewise the microscopy studies, the optical reflectivity measurements also show a sequential reduction in the reflectivity values (i.e., enhancement in the fuzz density) up to 973 K and after then a sequential enhancement in the reflectivity values (i.e., reduction in the fuzz density) with target temperatures. This is in well agreement with microscopy studies where we observed clear temperature window for Mo fuzz growth
Alvarado-Barrientos, M. S.; Holwerda, F.; Salazar-Martinez, D.
2014-12-01
Although land use change (LUC) is an important driver of changes in climate, very limited field observations of atmosphere-landscape interactions exist in tropical montane zones to examine the extent to which LUCs affect climate locally and regionally. The lack of ground observations hampers the evaluation of satellite-derived datasets of land surface parameters as well as the validation of regional climate models. The first results of an ongoing study of the climate effects of a LUC trajectory in the lower montane region (1200 m a.s.l.) of central Veracruz, Mexico, are presented. The radiation balance, turbulent fluxes and soil heat flux were measured in order to obtain field-derived land surface parameters (albedo and Bowen ratio) of two contrasting land uses: shaded coffee (CO) and sugarcane (SU) plantations. Measurements were conducted on days representing different seasons and crop stages during 2014: cold-dry (January), warm-dry (March) and warm-wet (July). Average noon-time albedo was higher for SU than for CO (0.14 vs. 0.11). Soil heat flux was on average 13% and 12% of net radiation for SU and CO, respectively. Preliminary turbulent flux calculations indicate that noon-time Bowen ratio was higher for sugar cane (range: 1.0-1.5) compared to shaded coffee (range: 0.5-1.0). Seasonal (and crop-stage) changes affected the surface parameters of SU mostly. For example, the SU Bowen ratio increased with decreasing soil moisture, indicating soil moisture limitation for transpiration reducing latent heat flux. In contrast, the shaded coffee Bowen ratio remained relatively constant across measuring periods. The energy balance closure was 80% (pending complete eddy covariance data corrections). These results indicate that the conversion of shaded coffee to sugarcane result in a drier and hotter lower atmosphere. Next steps include examining the implications of these local changes for regional climate, with special attention to cloud formation, using a regional model
Analysis of phononic bandgap structures with dissipation
DEFF Research Database (Denmark)
Andreassen, Erik; Jensen, Jakob Søndergaard
2013-01-01
We study wave propagation in periodic materials with dissipation using two different formulations. An ω(k)-formulation yields complex frequency solutions for nonvanishing dissipation whereas a k(ω)-formulation leads to complex wave numbers. For small (realistic) levels of material dissipation and...
Dynamics of dissipative systems and computational physics
International Nuclear Information System (INIS)
Adam, Gh.; Scutaru, H.; Ixaru, L.; Adam, S.; Rizea, M.; Stefanescu, E.; Mihalache, D.; Mazilu, D.; Crasovan, L.
2002-01-01
During the first year of research activity in the frame of this project there have been investigated two main topics: I. Dynamics of systems of fermions in complex dissipative media; II. Solitons with topologic charge in dissipative systems. An essential problem of the quantum information systems is the controllability and observability of the quantum states, generally described by Lindblad's master equation with phenomenological coefficients. In its usual form, this equation describes a decay of the mean-values, but not necessarily the expected decaying transitions. The basic and very difficult problem of a dissipative quantum theory is to project the evolution of the total system (the system of interest + the environment) on the space of the system of interest. In this case, one obtains a quantum master equation where the system evolution is described by two terms: 1) a Hamiltonian term for the processes with energy conservation, and 2) a non-Hamiltonian term with coefficients depending on the dissipative coupling. That means that a master equation is based on some approximations enabling the replacement of the operators of the dissipative environment with average value coefficients. It is often assumed that the evolution operators of the dissipative system define a semigroup, not a group as in the case of an isolated system. In this framework, Lindblad obtained a quantum master equation in agreement with all the quantum-mechanical principles. However, the Lindblad master equation was unable to secure a correct description of the decaying states. To do that, one has to take into account the transition operators between the system eigenstates with appropriate coefficients. Within this investigation, we have obtained an equation obeying to this requirement, giving the ρ(t) time derivative in terms of creation-annihilation operators of the single-particle states |i>, and λ ij , representing the dissipative coefficients, the microscopic expressions of which are
Fluctuation-dissipation relation for nonlinear Langevin equations.
Kumaran, V
2011-04-01
It is shown that the fluctuation-dissipation theorem is satisfied by the solutions of a general set of nonlinear Langevin equations with a quadratic free-energy functional (constant susceptibility) and field-dependent kinetic coefficients, provided the kinetic coefficients satisfy the Onsager reciprocal relations for the irreversible terms and the antisymmetry relations for the reversible terms. The analysis employs a perturbation expansion of the nonlinear terms, and a functional integral calculation of the correlation and response functions, and it is shown that the fluctuation-dissipation relation is satisfied at each order in the expansion. ©2011 American Physical Society
Elbelt, Ulf; Schuetz, Tatjana; Knoll, Nina; Burkert, Silke
2015-07-16
Reduced physical activity and almost unlimited availability of food are major contributors to the development of obesity. With the decline of strenuous work, energy expenditure due to spontaneous physical activity has attracted increasing attention. Our aim was to assess changes in energy expenditure, physical activity patterns and nutritional habits in obese subjects aiming at self-directed weight loss. Energy expenditure and physical activity patterns were measured with a portable armband device. Nutritional habits were assessed with a food frequency questionnaire. Data on weight development, energy expenditure, physical activity patterns and nutritional habits were obtained for 105 patients over a six-month period from an initial cohort of 160 outpatients aiming at weight loss. Mean weight loss was -1.5 ± 7.0 kg (p = 0.028). Patients with weight maintenance (n = 75), with substantial weight loss (>5% body weight, n = 20) and with substantial weight gain (>5% body weight, n = 10) did not differ in regard to changes of body weight adjusted energy expenditure components (total energy expenditure: -0.2 kcal/kg/day; non-exercise activity thermogenesis: -0.3 kcal/kg/day; exercise-related activity thermogenesis (EAT): -0.2 kcal/kg/day) or patterns of physical activity (duration of EAT: -2 min/day; steps/day: -156; metabolic equivalent unchanged) measured objectively with a portable armband device. Self-reported consumption frequency of unfavorable food decreased significantly (p = 0.019) over the six-month period. An increase in energy expenditure or changes of physical activity patterns (objectively assessed with a portable armband device) are not employed by obese subjects to achieve self-directed weight loss. However, modified nutritional habits could be detected with the use of a food frequency questionnaire.
Directory of Open Access Journals (Sweden)
Ulf Elbelt
2015-07-01
Full Text Available Reduced physical activity and almost unlimited availability of food are major contributors to the development of obesity. With the decline of strenuous work, energy expenditure due to spontaneous physical activity has attracted increasing attention. Our aim was to assess changes in energy expenditure, physical activity patterns and nutritional habits in obese subjects aiming at self-directed weight loss. Methods: Energy expenditure and physical activity patterns were measured with a portable armband device. Nutritional habits were assessed with a food frequency questionnaire. Results: Data on weight development, energy expenditure, physical activity patterns and nutritional habits were obtained for 105 patients over a six-month period from an initial cohort of 160 outpatients aiming at weight loss. Mean weight loss was −1.5 ± 7.0 kg (p = 0.028. Patients with weight maintenance (n = 75, with substantial weight loss (>5% body weight, n = 20 and with substantial weight gain (>5% body weight, n = 10 did not differ in regard to changes of body weight adjusted energy expenditure components (total energy expenditure: −0.2 kcal/kg/day; non-exercise activity thermogenesis: −0.3 kcal/kg/day; exercise-related activity thermogenesis (EAT: −0.2 kcal/kg/day or patterns of physical activity (duration of EAT: −2 min/day; steps/day: −156; metabolic equivalent unchanged measured objectively with a portable armband device. Self-reported consumption frequency of unfavorable food decreased significantly (p = 0.019 over the six-month period. Conclusions: An increase in energy expenditure or changes of physical activity patterns (objectively assessed with a portable armband device are not employed by obese subjects to achieve self-directed weight loss. However, modified nutritional habits could be detected with the use of a food frequency questionnaire.
International Nuclear Information System (INIS)
Åberg, M.; Henning, D.
2011-01-01
The development towards more energy efficient buildings, as well as the expansion of district heating (DH) networks, is generally considered to reduce environmental impact. But the combined effect of these two progressions is more controversial. A reduced heat demand (HD) due to higher energy efficiency in buildings might hamper co-production of electricity and DH. In Sweden, co-produced electricity is normally considered to displace electricity from less efficient European condensing power plants. In this study, a potential HD reduction due to energy efficiency measures in the existing building stock in the Swedish city Linköping is calculated. The impact of HD reduction on heat and electricity production in the Linköping DH system is investigated by using the energy system optimisation model MODEST. Energy efficiency measures in buildings reduce seasonal HD variations. Model results show that HD reductions primarily decrease heat-only production. The electricity-to-heat output ratio for the system is increased for HD reductions up to 30%. Local and global CO 2 emissions are reduced. If co-produced electricity replaces electricity from coal-fired condensing power plants, a 20% HD reduction is optimal for decreasing global CO 2 emissions in the analysed DH system. - Highlights: ► A MODEST optimisation model of the Linköping district heating system is used. ► The impact of heat demand reduction on heat and electricity production is examined. ► Model results show that heat demand reductions decrease heat-only production. ► Local and global CO 2 emissions are reduced. ► The system electricity-to-heat output increases for reduced heat demand up to 30%.
Kinetic approach to relativistic dissipation
Gabbana, A.; Mendoza, M.; Succi, S.; Tripiccione, R.
2017-08-01
Despite a long record of intense effort, the basic mechanisms by which dissipation emerges from the microscopic dynamics of a relativistic fluid still elude complete understanding. In particular, several details must still be finalized in the pathway from kinetic theory to hydrodynamics mainly in the derivation of the values of the transport coefficients. In this paper, we approach the problem by matching data from lattice-kinetic simulations with analytical predictions. Our numerical results provide neat evidence in favor of the Chapman-Enskog [The Mathematical Theory of Non-Uniform Gases, 3rd ed. (Cambridge University Press, Cambridge, U.K., 1970)] procedure as suggested by recent theoretical analyses along with qualitative hints at the basic reasons why the Chapman-Enskog expansion might be better suited than Grad's method [Commun. Pure Appl. Math. 2, 331 (1949), 10.1002/cpa.3160020403] to capture the emergence of dissipative effects in relativistic fluids.
Anisotropy dissipation in quantum cosmology
International Nuclear Information System (INIS)
Calzetta, E.; Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon I, 1428 Buenos Aires, Argentina)
1991-01-01
We study the issue of decoherence and dissipation in the wave function of the Universe for a Bianchi type-I universe with classical and quantum matter. We obtain a coarse-grained description by tracing over the matter degrees of freedom. Provided that for small universes the wave function of the universe is concentrated on a neighborhood of the isotropic configuration, then the coarse-grained density matrix of the universe will show an even more marked peak around isotropy for large universes. In this sense we can say that, while decoherence makes the reduced density matrix of the universe diagonal, dissipation causes the universe to be isotropic with a high probability for large radii
A model for turbulent dissipation rate in a constant pressure ...
Indian Academy of Sciences (India)
J Dey
flow quantities. Comparable agreement between the estimated Taylor microscale and Kolmogorov length scale with other data ... experimentally. Keywords. Boundary layers; dissipation rate; Kolmogorov length scale; Taylor microscale. 1. ... practice due to complexity involved in estimating these quantities. Segalini et al [2] ...
Mathematical homogenization of inelastic dissipative materials: a survey and recent progress
Charalambakis, Nicolas; Chatzigeorgiou, George; Chemisky, Yves; Meraghni, Fodil
2018-01-01
In this paper, a review of papers on mathematical homogenization of dissipative composites under small strains and on the interplay between homogenization procedure and dissipation due to mechanical work is presented. Moreover, a critical survey on the links between mathematical homogenization and computational homogenization is attempted.
Prasetyo, R Heru; Hestianah, Eka Pramyrtha
2017-06-01
This study was to evaluate effect of honey in repairing damage of liver tissue due to energy protein malnutrition and in mobilization of endogenous stem cells. Male mice model of degenerative liver was obtained through food fasting but still have drinking water for 5 days. It caused energy protein malnutrition and damage of liver tissue. The administration of 50% (v/v) honey was performed for 10 consecutive days, while the positive control group was fasted and not given honey and the negative control not fasted and without honey. Observations of regeneration the liver tissue based on histologically examination, observation of Hsp70 expression, and homing signal based on vascular endothelial growth factor-1 (VEGF-1) expression using immunohistochemistry technique. Observation on expression of CD34 and CD45 as the marker of auto mobilization of hematopoietic stem cells using flow cytometry technique. There is regeneration of the liver tissue due to protein energy malnutrition, decrease of Hsp70 expression, increase of VEGF-1 expression, and high expression of CD34 and CD45. Honey can improve the liver tissue based on: (1) Mobilization of endogenous stem cells (CD34 and CD45); (2) Hsp70 and VEGF-1 expressions as regeneration marker of improvement, and (3) regeneration histologically of liver tissue.
Anisotropic dissipation in lattice metamaterials
Directory of Open Access Journals (Sweden)
Dimitri Krattiger
2016-12-01
Full Text Available Plane wave propagation in an elastic lattice material follows regular patterns as dictated by the nature of the lattice symmetry and the mechanical configuration of the unit cell. A unique feature pertains to the loss of elastodynamic isotropy at frequencies where the wavelength is on the order of the lattice spacing or shorter. Anisotropy may also be realized at lower frequencies with the inclusion of local resonators, especially when designed to exhibit directionally non-uniform connectivity and/or cross-sectional geometry. In this paper, we consider free and driven waves within a plate-like lattice−with and without local resonators−and examine the effects of damping on the isofrequency dispersion curves. We also examine, for free waves, the effects of damping on the frequency-dependent anisotropy of dissipation. Furthermore, we investigate the possibility of engineering the dissipation anisotropy by tuning the directional properties of the prescribed damping. The results demonstrate that uniformly applied damping tends to reduce the intensity of anisotropy in the isofrequency dispersion curves. On the other hand, lattice crystals and metamaterials are shown to provide an excellent platform for direction-dependent dissipation engineering which may be realized by simple changes in the spatial distribution of the damping elements.
Dynamics of dissipative self-assembly of particles interacting through oscillatory forces.
Tagliazucchi, M; Szleifer, I
2016-01-01
Dissipative self-assembly is the formation of ordered structures far from equilibrium, which continuously uptake energy and dissipate it into the environment. Due to its dynamical nature, dissipative self-assembly can lead to new phenomena and possibilities of self-organization that are unavailable to equilibrium systems. Understanding the dynamics of dissipative self-assembly is required in order to direct the assembly to structures of interest. In the present work, Brownian dynamics simulations and analytical theory were used to study the dynamics of self-assembly of a mixture of particles coated with weak acids and bases under continuous oscillations of the pH. The pH of the system modulates the charge of the particles and, therefore, the interparticle forces oscillate in time. This system produces a variety of self-assembled structures, including colloidal molecules, fibers and different types of crystalline lattices. The most important conclusions of our study are: (i) in the limit of fast oscillations, the whole dynamics (and not only those at the non-equilibrium steady state) of a system of particles interacting through time-oscillating interparticle forces can be described by an effective potential that is the time average of the time-dependent potential over one oscillation period; (ii) the oscillation period is critical to determine the order of the system. In some cases the order is favored by very fast oscillations while in others small oscillation frequencies increase the order. In the latter case, it is shown that slow oscillations remove kinetic traps and, thus, allow the system to evolve towards the most stable non-equilibrium steady state.
Confronting GRB prompt emission with a model for subphotospheric dissipation
Ahlgren, Björn; Larsson, Josefin; Nymark, Tanja; Ryde, Felix; Pe'er, Asaf
2015-11-01
The origin of the prompt emission in gamma-ray bursts (GRBs) is still an unsolved problem and several different mechanisms have been suggested. Here, we fit Fermi GRB data with a photospheric emission model which includes dissipation of the jet kinetic energy below the photosphere. The resulting spectra are dominated by Comptonization and contain no significant contribution from synchrotron radiation. In order to fit to the data, we span a physically motivated part of the model's parameter space and create DREAM (Dissipation with Radiative Emission as A table Model), a table model for XSPEC. We show that this model can describe different kinds of GRB spectra, including GRB 090618, representing a typical Band function spectrum, and GRB 100724B, illustrating a double peaked spectrum, previously fitted with a Band+blackbody model, suggesting they originate from a similar scenario. We suggest that the main difference between these two types of bursts is the optical depth at the dissipation site.
Dissipative dark matter halos: The steady state solution
Foot, R.
2018-02-01
Dissipative dark matter, where dark matter particle properties closely resemble familiar baryonic matter, is considered. Mirror dark matter, which arises from an isomorphic hidden sector, is a specific and theoretically constrained scenario. Other possibilities include models with more generic hidden sectors that contain massless dark photons [unbroken U (1 ) gauge interactions]. Such dark matter not only features dissipative cooling processes but also is assumed to have nontrivial heating sourced by ordinary supernovae (facilitated by the kinetic mixing interaction). The dynamics of dissipative dark matter halos around rotationally supported galaxies, influenced by heating as well as cooling processes, can be modeled by fluid equations. For a sufficiently isolated galaxy with a stable star formation rate, the dissipative dark matter halos are expected to evolve to a steady state configuration which is in hydrostatic equilibrium and where heating and cooling rates locally balance. Here, we take into account the major cooling and heating processes, and numerically solve for the steady state solution under the assumptions of spherical symmetry, negligible dark magnetic fields, and that supernova sourced energy is transported to the halo via dark radiation. For the parameters considered, and assumptions made, we were unable to find a physically realistic solution for the constrained case of mirror dark matter halos. Halo cooling generally exceeds heating at realistic halo mass densities. This problem can be rectified in more generic dissipative dark matter models, and we discuss a specific example in some detail.
Dissipative control for singular impulsive dynamical systems
Directory of Open Access Journals (Sweden)
Li Yang
2012-04-01
Full Text Available The aim of this work is to study the dissipative control problem for singular impulsive dynamical systems. We start by introducing the impulse to the singular systems, and give the definition of the dissipation for singular impulsive dynamical systems. Then we discuss the dissipation of singular impulsive dynamical systems, we obtain some sufficient and necessary conditions for dissipation of these systems by solving some linear matrix inequalities (LMIs. By using this method, we design a state feedback controller to make the closed-loop system dissipative. At last, we testify the feasibility of the method by a numerical example.
Non-Dissipative Structural Evolutions in Granular Materials
Directory of Open Access Journals (Sweden)
Pouragha Mehdi
2017-01-01
Full Text Available The structure of the contact network in granular assemblies can evolve due to either dissipative mechanisms such as sliding at contact points, or non-dissipative mechanisms through the phenomenon of contact gain and loss. Being associated with negligible deformations, non-dissipative mechanisms is actually active even in the small strain range of ~ 10−3, especially in the case of densely packed assemblies. Hence, from a constitutive modelling point of view, it is crucial to be able to estimate such non-dissipative evolutions since both elastic and plastic properties of granular assemblies highly depend on contact network characteristics. The current study proposes an analytical scheme that allows us to estimate the non-dissipative contact gain/loss regime in terms of directional changes in the average contact force. The probability distribution of contact forces is used to compute the number of lost contact for each direction. Similarly, the number of newly formed contacts is estimated by considering the probability distribution of the gap between neighbouring particles. Based on the directional contact gain/loss computed, the changes in coordination number and fabric anisotropy can be found which, together with statistical treatments of Love-Weber stress expression, form a complete system of equations describing the evolution of other controlling microvariables. Finally, the results of the calculations have been compared with DEM simulations which verify the accuracy of the proposed scheme.
Evaluation of turbulent dissipation rate retrievals from Doppler Cloud Radar
Directory of Open Access Journals (Sweden)
M. D. Shupe
2012-06-01
Full Text Available Turbulent dissipation rate retrievals from cloud radar Doppler velocity measurements are evaluated using independent, in situ observations in Arctic stratocumulus clouds. In situ validation data sets of dissipation rate are derived using sonic anemometer measurements from a tethered balloon and high frequency pressure variation observations from a research aircraft, both flown in proximity to stationary, ground-based radars. Modest biases are found among the data sets in particularly low- or high-turbulence regimes, but in general the radar-retrieved values correspond well with the in situ measurements. Root mean square differences are typically a factor of 4–6 relative to any given magnitude of dissipation rate. These differences are no larger than those found when comparing dissipation rates computed from tethered-balloon and meteorological tower-mounted sonic anemometer measurements made at spatial distances of a few hundred meters. Temporal lag analyses suggest that approximately half of the observed differences are due to spatial sampling considerations, such that the anticipated radar-based retrieval uncertainty is on the order of a factor of 2–3. Moreover, radar retrievals are clearly able to capture the vertical dissipation rate structure observed by the in situ sensors, while offering substantially more information on the time variability of turbulence profiles. Together these evaluations indicate that radar-based retrievals can, at a minimum, be used to determine the vertical structure of turbulence in Arctic stratocumulus clouds.
Non-Dissipative Structural Evolutions in Granular Materials
Pouragha, Mehdi; Wan, Richard
2017-06-01
The structure of the contact network in granular assemblies can evolve due to either dissipative mechanisms such as sliding at contact points, or non-dissipative mechanisms through the phenomenon of contact gain and loss. Being associated with negligible deformations, non-dissipative mechanisms is actually active even in the small strain range of 10-3, especially in the case of densely packed assemblies. Hence, from a constitutive modelling point of view, it is crucial to be able to estimate such non-dissipative evolutions since both elastic and plastic properties of granular assemblies highly depend on contact network characteristics. The current study proposes an analytical scheme that allows us to estimate the non-dissipative contact gain/loss regime in terms of directional changes in the average contact force. The probability distribution of contact forces is used to compute the number of lost contact for each direction. Similarly, the number of newly formed contacts is estimated by considering the probability distribution of the gap between neighbouring particles. Based on the directional contact gain/loss computed, the changes in coordination number and fabric anisotropy can be found which, together with statistical treatments of Love-Weber stress expression, form a complete system of equations describing the evolution of other controlling microvariables. Finally, the results of the calculations have been compared with DEM simulations which verify the accuracy of the proposed scheme.
Hong, Seung Hwan; Bok, Jin Mo; Zhang, Wentao; He, Junfeng; Zhou, X J; Varma, C M; Choi, Han-Yong
2014-08-01
There is an enormous interest in the renormalization of the quasiparticle (qp) dispersion relation of cuprate superconductors both below and above the critical temperature T_{c} because it enables the determination of the fluctuation spectrum to which the qp's are coupled. A remarkable discovery by angle-resolved photoemission spectroscopy (ARPES) is a sharp low-energy feature (LEF) in qp spectra well below the superconducting energy gap but with its energy increasing in proportion to T_{c} and its intensity increasing sharply below T_{c}. This unexpected feature needs to be reconciled with d-wave superconductivity. Here, we present a quantitative analysis of ARPES data from Bi_{2}Sr_{2}CaCu_{2}O_{8+δ} (Bi2212) using Eliashberg equations to show that the qp scattering rate due to the forward scattering impurities far from the Cu-O planes is modified by the energy gap below T_{c} and shows up as the LEF. This is also a necessary step to analyze ARPES data to reveal the spectrum of fluctuations promoting superconductivity.
Neural network training as a dissipative process.
Gori, Marco; Maggini, Marco; Rossi, Alessandro
2016-09-01
This paper analyzes the practical issues and reports some results on a theory in which learning is modeled as a continuous temporal process driven by laws describing the interactions of intelligent agents with their own environment. The classic regularization framework is paired with the idea of temporal manifolds by introducing the principle of least cognitive action, which is inspired by the related principle of mechanics. The introduction of the counterparts of the kinetic and potential energy leads to an interpretation of learning as a dissipative process. As an example, we apply the theory to supervised learning in neural networks and show that the corresponding Euler-Lagrange differential equations can be connected to the classic gradient descent algorithm on the supervised pairs. We give preliminary experiments to confirm the soundness of the theory. Copyright © 2016 Elsevier Ltd. All rights reserved.
Quantum thermodynamics for driven dissipative bosonic systems
Ochoa, Maicol A.; Zimbovskaya, Natalya; Nitzan, Abraham
2018-02-01
We investigate two prototypical dissipative bosonic systems under slow driving and arbitrary system-bath coupling strength, recovering their dynamic evolution as well as the heat and work rates, and we verify that thermodynamic laws are respected. Specifically, we look at the damped harmonic oscillator and the damped two-level system. For the former, we study independently the slow time-dependent perturbation in the oscillator frequency and in the coupling strength. For the latter, we concentrate on the slow modulation of the energy gap between the two levels. Importantly, we are able to find the entropy production rates for each case without explicitly defining nonequilibrium extensions for the entropy functional. This analysis also permits the definition of phenomenological friction coefficients in terms of structural properties of the system-bath composite.
Mishev, A. L.; Velinov, P. I. Y.
2018-01-01
The influence of high energy particles, specifically cosmic rays, on atmospheric physics and chemistry is highly discussed. In most of the proposed models the role of ionization in the atmosphere due to cosmic rays is not negligible. Moreover, effect(s) on minor constituents and aerosols are recently observed, specifically over the polar regions during strong solar particle events. According to the recent findings for such effects it is necessary an essential increase of ion production, specifically during the winter period. The galactic cosmic rays are the main source of ionization in the Earth's stratosphere and troposphere. Occasionally, the atmospheric ionization is significantly enhanced during strong solar energetic particles events, specifically over the polar caps. During the solar cycle 23 several strong ground level enhancements were observed. One of the strongest was the Bastille day event occurred on 14 July 2000. Using a full Monte Carlo 3-D model, we compute the atmospheric ionization, considering explicitly the contribution of cosmic rays with galactic and solar origin, focusing on high energy particles. The model is based on atmospheric cascade simulation with the PLANETOCOSMICS code. The ion production rate is computed as a function of the altitude above the sea level. The ion production rate is computed on a step ranging from 10 to 30 min throughout the event, considering explicitly the spectral and angular characteristics of the high energy part of solar protons as well as their time evolution. The corresponding event averaged ionization effect relative to the average due to galactic cosmic rays is computed in lower stratosphere and upper troposphere at various altitudes, namely 20 km, 15 km, 12 km and 8 km above the sea level in a sub-polar and polar regions. The 24h and the weekly ionization effects are also computed in the troposphere and low stratosphere. Several applications are discussed.
Chen, Xiankai
2017-04-21
In the most efficient solar cells based on blends of a conjugated polymer (electron donor) and a fullerene derivative (electron acceptor),ultrafast formation of charge-transfer (CT) electronic states at the donor-acceptor interfaces and efficient separation of these CT states into free charges, lead to internal quantum efficiencies near 100%. However, there occur substantial energy losses due to the non-radiative recombinations of the charges, mediated by the loweset-energy (singlet and triplet) CT states; for example, such recombinations can lead to the formation of triplet excited electronic states on the polymer chains, which do not generate free charges. This issue remains a major factor limiting the power conversion efficiencies (PCE) of these devices. The recombination rates are, however, difficult to quantify experimentally. To shed light on these issues, here, an integrated multi-scale theoretical approach that combines molecular dynamics simulations with quantum chemistry calculations is employed in order to establish the relationships among chemical structures, molecular packing, and non-radiative recombination losses mediated by the lowest-energy charge-transfer states.
Energy Technology Data Exchange (ETDEWEB)
Raynolds, J.E. [Lockheed Martin Corp., Schenectady, NY (United States)
1998-10-01
Theoretical studies have demonstrated that the energy transfer between a hot and cold body at close spacing (on the order of the radiation wavelength) can greatly exceed the limit for black body radiation (ie, Power = {sigma}T{sup 4}). This effect, due to the coupling of evanescent fields, presents an attractive option for thermo-photovoltaic (TPV) applications (assuming the considerable technical challenges can be overcome). The magnitude of the enhanced energy transfer depends on the optical properties of the hot and cold bodies as characterized by the dielectric functions of the respective materials. The present study considers five different situations as specified by the materials choices for the hot/cold sides: metal/metal, metal/insulator, metal/semiconductor, insulator/insulator, and semiconductor/semiconductor. For each situation, the dielectric functions are specified by typical models. An increase in energy transfer (relative to the black body law) is found for all situations considered, for separations less than one micron, assuming a temperature difference of 1,000 C. The metal/metal situation has the highest increase vs. separation while the semiconductor/semiconductor has the lowest. Factor-of-ten increases are obtained at roughly 0.1 microns for the metal/metal and roughly 0.02 microns for the metal/semiconductor. These studies are helping to increase the understanding of the close-spaced effect in the context of a radiator/TPV context.
International Nuclear Information System (INIS)
Yasuda, Yohei; Kato, Hiroyuki; Sasaki, Kazuaki
2012-01-01
Superelasticity in Ni–Ti polycrystal is examined in terms of the second law of thermodynamics. As a consequence of the law, both the phase equilibrium and the dissipation of mechanical energy during the stress-induced martensitic transformation have been formulated simultaneously by means of the Clausius–Duhem inequality. The flow stress of superelasticity has been derived as the function of temperature. The energy dissipated in the shape memory effect is briefly discussed.
Comparison of calculated energy flux of internal tides with microstructure measurements
Directory of Open Access Journals (Sweden)
Saeed Falahat
2014-10-01
Full Text Available Vertical mixing caused by breaking of internal tides plays a major role in maintaining the deep-ocean stratification. This study compares observations of dissipation from microstructure measurements to calculations of the vertical energy flux from barotropic to internal tides, taking into account the temporal variation due to the spring-neap tidal cycle. The dissipation data originate from two surveys in the Brazil Basin Tracer Release Experiment (BBTRE, and one over the LArval Dispersal along the Deep East Pacific Rise (LADDER3, supplemented with a few stations above the North-Atlantic Ridge (GRAVILUCK and in the western Pacific (IZU. A good correlation is found between logarithmic values of energy flux and local dissipation in BBTRE, suggesting that the theory is able to predict energy fluxes. For the LADDER3, the local dissipation is much smaller than the calculated energy flux, which is very likely due to the different topographic features of BBTRE and LADDER3. The East Pacific Rise consists of a few isolated seamounts, so that most of the internal wave energy can radiate away from the generation site, whereas the Brazil Basin is characterised by extended rough bathymetry, leading to a more local dissipation. The results from all four field surveys support the general conclusion that the fraction of the internal-tide energy flux that is dissipated locally is very different in different regions.
Sopori, Bhushan L.
1995-01-01
A method and apparatus for improving the accuracy of the simulation of sunlight reaching the earth's surface includes a relatively small heated chamber having an optical inlet and an optical outlet, the chamber having a cavity that can be filled with a heated stream of CO.sub.2 and water vapor. A simulated beam comprising infrared and near infrared light can be directed through the chamber cavity containing the CO.sub.2 and water vapor, whereby the spectral characteristics of the beam are altered so that the output beam from the chamber contains wavelength bands that accurately replicate atmospheric absorption of solar energy due to atmospheric CO.sub.2 and moisture.
Sopori, B.L.
1995-06-20
A method and apparatus for improving the accuracy of the simulation of sunlight reaching the earth`s surface includes a relatively small heated chamber having an optical inlet and an optical outlet, the chamber having a cavity that can be filled with a heated stream of CO{sub 2} and water vapor. A simulated beam comprising infrared and near infrared light can be directed through the chamber cavity containing the CO{sub 2} and water vapor, whereby the spectral characteristics of the beam are altered so that the output beam from the chamber contains wavelength bands that accurately replicate atmospheric absorption of solar energy due to atmospheric CO{sub 2} and moisture. 8 figs.
Directory of Open Access Journals (Sweden)
Aurang Zaib
2016-01-01
Full Text Available The two-dimensional boundary layer flow of a non-Newtonian Casson fluid and heat transfer due to an exponentially permeable shrinking sheet with viscous dissipation is investigated. Using similarity transformations, the governing momentum and energy equations are transformed to self-similar nonlinear ODEs and then those are solved numerically by very efficient shooting method. The analysis explores many important aspects of flow and heat transfer of the aforesaid non-Newtonian fluid flow dynamics. For the steady flow of non-Newtonian Casson fluid, more amount of wall mass suction through the porous sheet is required in comparison to that of Newtonian fluid flow. Dual similarity solutions are obtained for velocity and temperature. The viscous dissipation effect has major impact on the heat transfer characteristic. In fact, heat absorption at the surface occurs and it increases due to viscous dissipation. For higher Prandtl number, the temperature inside the boundary layer reduces, but with larger Eckert number (viscous dissipation it is enhanced.
International Nuclear Information System (INIS)
Gloaguen, Olivier; Alberola, Emilie
2013-01-01
Among the publications of CDC Climat Research, 'Climate Briefs' presents, in a few pages, hot topics in climate change policy. This issue addresses the following points: - CO 2 emissions generated by installations covered by the EU ETS decreased by 12.3 % since 2005, i.e a decline by 2.6% per year during Phase 2 of the EU ETS while the emission cap increased by 1% per year. - The EU ETS ended Phase 2 with a surplus of 1,742 million of allowances. All sectors recorded an overall net surplus, except for the power generation and co-generation sectors. - Based on a 'business-as-usual' scenario, we estimate that around 1.1 GtCO 2 were avoided between 2005 and 2011: around 30% of the reduction was the result of a fall in manufacturing output, while around 60% of the reduction was caused by the development of renewable energy and the improvement of the energy intensity
Arriga, Nicola; Fratini, Gerardo; Forgione, Antonio; Tomassucci, Michele; Papale, Dario
2010-05-01
Eddy covariance is a well established and widely used methodology for the measurement of turbulent fluxes of mass and energy in the atmospheric boundary layer, in particular to estimate CO2/H2O and heat exchange above ecologically relevant surfaces (Aubinet 2000, Baldocchi 2003). Despite its long term application and theoretical studies, many issues are still open about the effect of different experimental set-up on final flux estimates. Open issues are the evaluation of the performances of different kind of sensors (e.g. open path vs closed path infra-red gas analysers, vertical vs horizontal mounting ultrasonic anemometers), the quantification of the impact of corresponding physical corrections to be applied to get robust flux estimates taking in account all processes concurring to the measurement (e.g. the so-called WPL term, signal attenuation due to air sampling system for closed path analyser, relative position of analyser and anemometer) and the differences between several data transmission protocols used (analogue, digital RS-232, SDM). A field experiment was designed to study these issues using several instruments among those most used within the Fluxnet community and to compare their performances under conditions supposed to be critical: rainy and cold weather conditions for open-path analysers (Burba 2008), water transport and absorption at high air relative humidity conditions for closed-path systems (Ibrom, 2007), frequency sampling limits and recorded data robustness due to different transmission protocols (RS232, SDM, USB, Ethernet) and finally the effect of the displacement between anemometer and analyser using at least two identical analysers placed at different horizontal and vertical distances from the anemometer. Aim of this experiment is to quantify the effect of several technical solutions on the final estimates of fluxes measured at a point in the space and if they represent a significant source of uncertainty for mass and energy cycle
Werth, D. W.
2016-12-01
The state of South Carolina, home to the Department of Energy's (DOE) Savannah River Site (SRS), has been identified as facing an `above average' risk due to extreme heat, and the threat due to wildfire is expected to nearly double by 2050. To comply with DOE requirements that each of its sites prepares for climate change, the Savannah River National Laboratory (SRNL) is involved in an ongoing process to evaluate the site vulnerability and establish policies to mitigate those effects. This requires close cooperation between the managers of various site facilities and on-site climate researchers. The Atmospheric Technologies Group at SRNL currently provides short-term weather forecasts to support outdoor activities on site, but is also now working with site decision-makers to achieve DOE's goals of climate change mitigation and adaptation. We will discuss the results of our climate vulnerability assessment, which includes the effects of climate change on the energy requirements for mission critical infrastructure, the health, safety and productivity of the outdoor workforce, the danger of fire in the SRS forest, and the levels of surface water impoundments. (The latter of which must be maintained to avoid the release of radioactive contaminants sequestered beneath them). For each of these, existing climate change projections were carefully studied and `translated' into numerical indices relevant to facility personnel at SRS, along with a vulnerability rating (also based on conversations with site workers) to estimate the most endangered `assets'. We will also explain the process we have developed to facilitate effective communication between researchers and managers - involving them both in the development of the climate vulnerability assessment and the next steps toward planning, resource allocation, actions to mitigate rising costs, and safety considerations as well as helping the site remain sustainable throughout the future of its missions.
Amphetamine enhances endurance by increasing heat dissipation.
Morozova, Ekaterina; Yoo, Yeonjoo; Behrouzvaziri, Abolhassan; Zaretskaia, Maria; Rusyniak, Daniel; Zaretsky, Dmitry; Molkov, Yaroslav
2016-09-01
Athletes use amphetamines to improve their performance through largely unknown mechanisms. Considering that body temperature is one of the major determinants of exhaustion during exercise, we investigated the influence of amphetamine on the thermoregulation. To explore this, we measured core body temperature and oxygen consumption of control and amphetamine-trea ted rats running on a treadmill with an incrementally increasing load (both speed and incline). Experimental results showed that rats treated with amphetamine (2 mg/kg) were able to run significantly longer than control rats. Due to a progressively increasing workload, which was matched by oxygen consumption, the control group exhibited a steady increase in the body temperature. The administration of amphetamine slowed down the temperature rise (thus decreasing core body temperature) in the beginning of the run without affecting oxygen consumption. In contrast, a lower dose of amphetamine (1 mg/kg) had no effect on measured parameters. Using a mathematical model describing temperature dynamics in two compartments (the core and the muscles), we were able to infer what physiological parameters were affected by amphetamine. Modeling revealed that amphetamine administration increases heat dissipation in the core. Furthermore, the model predicted that the muscle temperature at the end of the run in the amphetamine-treated group was significantly higher than in the control group. Therefore, we conclude that amphetamine may mask or delay fatigue by slowing down exercise-induced core body temperature growth by increasing heat dissipation. However, this affects the integrity of thermoregulatory system and may result in potentially dangerous overheating of the muscles. © 2016 The Authors. Physiological Reports published by Wiley Periodicals, Inc. on behalf of the American Physiological Society and The Physiological Society.
Gao, Bo; Ma, Chunyang; Huo, Jiayu; Guo, Yubin; Sun, Tiegang; Wu, Ge
2018-03-01
We investigate the influence of gain fiber on dissipative soliton pairs in passively mode-locked (PML) fiber laser based on black phosphorus (BP) as a saturable absorber. Numerical simulations show that we can generate the dissipative soliton pairs in PML fiber laser when the gain fiber parameters (gain saturation energy and gain bandwidth) are in an appropriate dynamic range, and the dissipative soliton pairs become unstable once the range is exceeded. Then we analyze the dynamic evolution of the dissipative soliton pairs and the influence of gain fiber on the pulse separation, peak power, and single-pulse energy of the dissipative solitons pairs.
The greenhouse effect: A new source of energy
International Nuclear Information System (INIS)
Meunier, Francis
2007-01-01
Climate change induced by global warming is a result of an excess of energy at the earth's surface due to the greenhouse effect. But a new energy management can reverse the situation taking advantage of the greenhouse effect to produce renewable energy. In fact, both the renewable energy and the energy consumed which are not dissipated into heat are subtracted from the excess of energy produced by the greenhouse effect and contribute to mitigate climate change. This opens perspectives to harness the greenhouse effect [F. Meunier, Domestiquer l'effet de serre, Dunod, 2005]. Should all the primary energy be renewable energy and should part of the energy production not dissipated into heat, the present earth's energy imbalance should be beneficial and should serve to produce renewable energy
Nondestructive evaluation of dissipative behavior of reinforced concrete structure
International Nuclear Information System (INIS)
Luong, M.P.
2001-01-01
Current technological developments tend toward increased exploitation of materials strengths and toward tackling extreme loads and environmental actions such as offshore structures subject to wind and wave loading, or buildings in seismic area. Concrete is widely used as a construction material because of its high strength-cost ratio in many applications. Experience of earthquakes and laboratory tests has shown that well designed and detailed reinforced concrete is suitable for earthquake resistant structures. The most severe likely earthquake can be survived if the members are sufficiently ductile to absorb and dissipate seismic energy by inelastic deformation. This requires a designer to assess realistically the acceptable levels of strength and to ensure adequate dissipation. This paper proposes the use of infrared thermography as a nondestructive, noncontact and real-time technique to examine diverse mechanisms of dissipation and to illustrate the onset of damage process, stress concentration and heat dissipation localization in loaded zone. In addition, this technique can be used as a nondestructive method for evaluating the fatigue limit of concrete structure subject to repeated loading
Irreversibility and dissipation in finite-state automata
International Nuclear Information System (INIS)
Ganesh, Natesh; Anderson, Neal G.
2013-01-01
Irreversibility and dissipation in finite-state automata (FSA) are considered from a physical-information-theoretic perspective. A quantitative measure for the computational irreversibility of finite automata is introduced, and a fundamental lower bound on the average energy dissipated per state transition is obtained and expressed in terms of FSA irreversibility. The irreversibility measure and energy bound are germane to any realization of a deterministic automaton that faithfully registers abstract FSA states in distinguishable states of a physical system coupled to a thermal environment, and that evolves via a sequence of interactions with an external system holding a physical instantiation of a random input string. The central result, which is shown to follow from quantum dynamics and entropic inequalities alone, can be regarded as a generalization of Landauer's Principle applicable to FSAs and tailorable to specified automata. Application to a simple FSA is illustrated.
Observed eddy dissipation in the Agulhas Current
CSIR Research Space (South Africa)
Braby, L
2016-08-01
Full Text Available Channel and south of Madagascar dissipate as they approach the Agulhas Current. By tracking the offshore position of the current core and its velocity at 30°S in relation to eddies, it is demonstrated that eddy dissipation occurs through a transfer...
Low moduli elastomers with low viscous dissipation
DEFF Research Database (Denmark)
Bejenariu, Anca Gabriela; Yu, Liyun; Skov, Anne Ladegaard
2012-01-01
A controlled reaction schema for addition curing silicones leads to both significantly lower elastic modulus and lower viscous dissipation than for the chemically identical network prepared by the traditional reaction schema.......A controlled reaction schema for addition curing silicones leads to both significantly lower elastic modulus and lower viscous dissipation than for the chemically identical network prepared by the traditional reaction schema....
Robust dissipativity for uncertain impulsive dynamical systems
Directory of Open Access Journals (Sweden)
Liu Bin
2003-01-01
Full Text Available We discuss the robust dissipativity with respect to the quadratic supply rate for uncertain impulsive dynamical systems. By employing the Hamilton-Jacobi inequality approach, some sufficient conditions of robust dissipativity for this kind of system are established. Finally, we specialize the obtained results to the case of uncertain linear impulsive dynamical systems.
Constructal entransy dissipation minimization for 'volume-point' heat conduction
International Nuclear Information System (INIS)
Chen Lingen; Wei Shuhuan; Sun Fengrui
2008-01-01
The 'volume to point' heat conduction problem, which can be described as to how to determine the optimal distribution of high conductivity material through the given volume such that the heat generated at every point is transferred most effectively to its boundary, has became the focus of attention in the current constructal theory literature. In general, the minimization of the maximum temperature difference in the volume is taken as the optimization objective. A new physical quantity, entransy, has been identified as a basis for optimizing heat transfer processes in terms of the analogy between heat and electrical conduction recently. Heat transfer analyses show that the entransy of an object describes its heat transfer ability, just as the electrical energy in a capacitor describes its charge transfer ability. Entransy dissipation occurs during heat transfer processes, as a measure of the heat transfer irreversibility with the dissipation related thermal resistance. By taking equivalent thermal resistance (it corresponds to the mean temperature difference), which reflects the average heat conduction effect and is defined based on entransy dissipation, as an optimization objective, the 'volume to point' constructal problem is re-analysed and re-optimized in this paper. The constructal shape of the control volume with the best average heat conduction effect is deduced. For the elemental area and the first order construct assembly, when the thermal current density in the high conductive link is linear with the length, the optimized shapes of assembly based on the minimization of entransy dissipation are the same as those based on minimization of the maximum temperature difference, and the mean temperature difference is 2/3 of the maximum temperature difference. For the second and higher order construct assemblies, the thermal current densities in the high conductive link are not linear with the length, and the optimized shapes of the assembly based on the
A REVIEW ON HEAT DISSIPATING PASSIVE COOLING TECHNIQUES FOR RESIDENTIAL BUILDINGS AT TROPICAL REGION
Directory of Open Access Journals (Sweden)
D. PRAKASH
2017-08-01
Full Text Available Thermal comfort is very essential for the occupants in a residential building without air-conditioning system especially in tropical region. Passive cooling is the only solution to achieve the required thermal comfort without sacrificing occupant’s health with zero energy consumption. All passive cooling techniques are broadly categorized under (i solar and heat protection, (ii heat modulation and (iii heat dissipation techniques. This paper reviews various techniques and advancements in passive cooling of buildings through heat dissipation approach. In the heat dissipation approach, the heat generated from various sources are reduced by natural ventilation and natural cooling.
Bounds on dissipation in stress-driven flow in a rotating frame
Tang, W.; Caulfield, C. P.; Young, W. R.
2005-09-01
We calculate a rigorous dual bound on the long-time-averaged mechanical energy dissipation rate varepsilon within a channel of an incompressible viscous fluid of constant kinematic viscosity nu, depth h and rotation rate f, driven by a constant surface stress {bmtau} {=} rho u(2_starxvec) , where u_star is the friction velocity. It is well known that varepsilon {≤} varepsilon_Stokes {=} u(4_star/nu) , i.e. the dissipation is bounded above by the dissipation associated with the Stokes flow.
Nuclear dissipation effects on fission and evaporation in systems of intermediate fissility
Directory of Open Access Journals (Sweden)
Gelli N.
2010-03-01
Full Text Available The systems of intermediate fissility 132Ce and 158Er have been studied experimentally and theoretically in order to investigate the dissipation properties of nuclear matter. Cross sections of fusion-fission and evaporation residues channels together with charged particles multiplicities in both channels, their spectra, angular correlations and mass-energy distribution of fission fragments have been measured. Theoretical analysis has been performed using multi-dimensional stochastic approach with realistic treatment of particle evaporation. The results of analysis show that full one-body or unusually strong two-body dissipation allows to reproduce experimental data. No temperature dependent dissipation was needed.
Magnetic Field Fluctuations Due to Diel Vertical Migrations of Zooplankton
Dean, C.; Soloviev, A.
2016-12-01
Dean et al. (2016) have indicated that at high zooplankton concentrations, diel vertical migrations (DVM) cause velocity fluctuations and a respective increase of the dissipation rate of turbulent kinetic energy (TKE). In this work, we used a 3D non-hydrostatic computational fluid dynamics model with Lagrangian particle injections (a proxy for migrating organisms) via a discrete phase model to simulate the effect of turbulence generation by DVM. We tested a range of organism concentrations from 1000 to 10,000 organisms/m3. The simulation at an extreme concentration of zooplankton showed an increase in dissipation rate of TKE by two to three orders of magnitude during DVM over background turbulence, 10-8 W kg-1. At lower concentrations (Frank, J. Wood, 2016: Biomixing due to diel vertical migrations of zooplankton. Ocean Modelling 98, 51-64.
Realization of a Tunable Dissipation Scale in a Turbulent Cascade using a Quantum Gas
Navon, Nir; Eigen, Christoph; Zhang, Jinyi; Lopes, Raphael; Smith, Robert; Hadzibabic, Zoran
2017-04-01
Many turbulent flows form so-called cascades, where excitations injected at large length scales, are transported to gradually smaller scales until they reach a dissipation scale. We initiate a turbulent cascade in a dilute Bose fluid by pumping energy at the container scale of an optical box trap using an oscillating magnetic force. In contrast to classical fluids where the dissipation scale is set by the viscosity of the fluid, the turbulent cascade of our quantum gas finishes when the particles kinetic energy exceeds the laser-trap depth. This mechanism thus allows us to effectively tune the dissipation scale where particles (and energy) are lost, and measure the particle flux in the cascade at the dissipation scale. We observe a unit power-law decay of the particle-dissipation rate with trap depth, which confirms the surprising prediction that in a wave-turbulent direct energy cascade, the particle flux vanishes in the ideal limit where the dissipation length scale tends to zero.
Dissipation enhanced vibrational sensing in an olfactory molecular switch
International Nuclear Information System (INIS)
Chęcińska, Agata; Heaney, Libby; Pollock, Felix A.; Nazir, Ahsan
2015-01-01
Motivated by a proposed olfactory mechanism based on a vibrationally activated molecular switch, we study electron transport within a donor-acceptor pair that is coupled to a vibrational mode and embedded in a surrounding environment. We derive a polaron master equation with which we study the dynamics of both the electronic and vibrational degrees of freedom beyond previously employed semiclassical (Marcus-Jortner) rate analyses. We show (i) that in the absence of explicit dissipation of the vibrational mode, the semiclassical approach is generally unable to capture the dynamics predicted by our master equation due to both its assumption of one-way (exponential) electron transfer from donor to acceptor and its neglect of the spectral details of the environment; (ii) that by additionally allowing strong dissipation to act on the odorant vibrational mode, we can recover exponential electron transfer, though typically at a rate that differs from that given by the Marcus-Jortner expression; (iii) that the ability of the molecular switch to discriminate between the presence and absence of the odorant, and its sensitivity to the odorant vibrational frequency, is enhanced significantly in this strong dissipation regime, when compared to the case without mode dissipation; and (iv) that details of the environment absent from previous Marcus-Jortner analyses can also dramatically alter the sensitivity of the molecular switch, in particular, allowing its frequency resolution to be improved. Our results thus demonstrate the constructive role dissipation can play in facilitating sensitive and selective operation in molecular switch devices, as well as the inadequacy of semiclassical rate equations in analysing such behaviour over a wide range of parameters
Energy Technology Data Exchange (ETDEWEB)
Pardo-Gomez, Rafael [Centro de Investigaciones Hidraulicas (Cuba)
2008-04-15
Ski-jump energy dissipators are widely used in hydraulic engineering because of their well-known effectiveness. Nevertheless, some uncertainty exits associated with the dimensions of the scour hole appearing downstream of the structure. This paper presents a new method for solving this problem. This method includes spillway stability checking as part of the design process and also stability checking of any other construction near the energy dissipation zone. [Spanish] Los disipadores de energia tipo trampolin tienen amplia utilizacion en la practica de la ingenieria hidraulica por su probada eficacia; sin embargo, su diseno esta sujeto a cierto grado de incertidumbre en cuanto a la prediccion de las dimensiones del cono de socavacion que habra de producirse aguas abajo de la estructura. En el presente trabajo se muestra un metodo novedoso, mediante el cual el autor soluciona el aspecto antes referido, toda vez que se incluye como parte del proceso de diseno la comprobacion de la estabilidad del propio aliviadero o de cualquier otra obra cercana a la zona de disipacion de energia.
Directory of Open Access Journals (Sweden)
Harold Díaz
2017-12-01
Full Text Available A method for obtaining two dimensional fields of wave breaking energy dissipation in the surfzone is presented. The method relies on acquiring geometrical parameters of the wave roller from remote sensing data. These parameters are then coupled with a dissipation model to obtain time averaged two dimensional maps, but also the wave breaking energy dissipation on a wave-by-wave basis. Comparison of dissipation maps as obtained from the present technique and a results from a numerical model, show very good correlation in both structure and magnitude. The location of a rip current can also be observed from the field data. Though in the present work a combination of optical and microwave data is used, the underlying method is independent of the remote sensor platform. Therefore, it offers the possibility to acquire high quality and synoptic estimates that could contribute to the understanding of the surfzone hydrodynamics.
Directory of Open Access Journals (Sweden)
H. Dupuis
Full Text Available Heat flux estimates obtained using the inertial dissipation method, and the profile method applied to radiosonde soundings, are assessed with emphasis on the parameterization of the roughness lengths for temperature and specific humidity. Results from the inertial dissipation method show a decrease of the temperature and humidity roughness lengths for increasing neutral wind speed, in agreement with previous studies. The sensible heat flux estimates were obtained using the temperature estimated from the speed of sound determined by a sonic anemometer. This method seems very attractive for estimating heat fluxes over the ocean. However allowance must be made in the inertial dissipation method for non-neutral stratification. The SOFIA/ASTEX and SEMAPHORE results show that, in unstable stratification, a term due to the transport terms in the turbulent kinetic energy budget, has to be included in order to determine the friction velocity with better accuracy. Using the profile method with radiosonde data, the roughness length values showed large scatter. A reliable estimate of the temperature roughness length could not be obtained. The humidity roughness length values were compatible with those found using the inertial dissipation method.
Properties of two-temperature dissipative accretion flow around black holes
Dihingia, Indu K.; Das, Santabrata; Mandal, Samir
2018-04-01
We study the properties of two-temperature accretion flow around a non-rotating black hole in presence of various dissipative processes where pseudo-Newtonian potential is adopted to mimic the effect of general relativity. The flow encounters energy loss by means of radiative processes acted on the electrons and at the same time, flow heats up as a consequence of viscous heating effective on ions. We assumed that the flow is exposed with the stochastic magnetic fields that leads to Synchrotron emission of electrons and these emissions are further strengthen by Compton scattering. We obtain the two-temperature global accretion solutions in terms of dissipation parameters, namely, viscosity (α) and accretion rate ({\\dot{m}}), and find for the first time in the literature that such solutions may contain standing shock waves. Solutions of this kind are multitransonic in nature, as they simultaneously pass through both inner critical point (xin) and outer critical point (xout) before crossing the black hole horizon. We calculate the properties of shock-induced global accretion solutions in terms of the flow parameters. We further show that two-temperature shocked accretion flow is not a discrete solution, instead such solution exists for wide range of flow parameters. We identify the effective domain of the parameter space for standing shock and observe that parameter space shrinks as the dissipation is increased. Since the post-shock region is hotter due to the effect of shock compression, it naturally emits hard X-rays, and therefore, the two-temperature shocked accretion solution has the potential to explain the spectral properties of the black hole sources.
Energy Technology Data Exchange (ETDEWEB)
Mancas, Stefan C. [Department of Mathematics, Embry–Riddle Aeronautical University, Daytona Beach, FL 32114-3900 (United States); Rosu, Haret C., E-mail: hcr@ipicyt.edu.mx [IPICYT, Instituto Potosino de Investigacion Cientifica y Tecnologica, Apdo Postal 3-74 Tangamanga, 78231 San Luis Potosí, SLP (Mexico)
2013-09-02
We emphasize two connections, one well known and another less known, between the dissipative nonlinear second order differential equations and the Abel equations which in their first-kind form have only cubic and quadratic terms. Then, employing an old integrability criterion due to Chiellini, we introduce the corresponding integrable dissipative equations. For illustration, we present the cases of some integrable dissipative Fisher, nonlinear pendulum, and Burgers–Huxley type equations which are obtained in this way and can be of interest in applications. We also show how to obtain Abel solutions directly from the factorization of second order nonlinear equations.
Observation of Coexisting Dissipative Solitons in a Mode-Locked Fiber Laser.
Bao, Chengying; Chang, Wonkeun; Yang, Changxi; Akhmediev, Nail; Cundiff, Steven T
2015-12-18
We show, experimentally and numerically, that a mode-locked fiber laser can operate in a regime where two dissipative soliton solutions coexist and the laser will periodically switch between the solutions. The two dissipative solitons differ in their pulse energy and spectrum. The switching can be controlled by an external perturbation and triggered even when switching does not occur spontaneously. Numerical simulations unveil the importance of the double-minima loss spectrum and nonlinear gain to the switching dynamics.
Research on the Heat Dissipation Characteristics of Lithium Battery Spatial Layout in an AUV
Zhaoyong Mao; Shaokun Yan
2016-01-01
To meet the power demand requirements of autonomous underwater vehicles (AUVs), the power supply is generally composed of a large number of high-energy lithium battery groups. The lithium battery heat dissipation properties not only affect the underwater vehicle performance but also bring some security risks. Based on the widespread application of lithium batteries, lithium batteries in an AUV are taken as an example to investigate the heat dissipation characteristics of the lithium battery s...
Enhanced Dissipation, Hypoellipticity, and Anomalous Small Noise Inviscid Limits in Shear Flows
Bedrossian, Jacob; Coti Zelati, Michele
2017-06-01
We analyze the decay and instant regularization properties of the evolution semigroups generated by two-dimensional drift-diffusion equations in which the scalar is advected by a shear flow and dissipated by full or partial diffusion. We consider both the space-periodic T^2 setting and the case of a bounded channel T × [0,1] with no-flux boundary conditions. In the infinite Péclet number limit (diffusivity {ν\\to 0}), our work quantifies the enhanced dissipation effect due to the shear. We also obtain hypoelliptic regularization, showing that solutions are instantly Gevrey regular even with only partial diffusion. The proofs rely on localized spectral gap inequalities and ideas from hypocoercivity with an augmented energy functional with weights replaced by pseudo-differential operators (of a rather simple form). As an application, we study small noise inviscid limits of invariant measures of stochastic perturbations of passive scalars, and show that the classical Freidlin scaling between noise and diffusion can be modified. In particular, although statistically stationary solutions blow up in {H^1} in the limit {ν \\to 0}, we show that viscous invariant measures still converge to a unique inviscid measure.
Current flow instability and nonlinear structures in dissipative two-fluid plasmas
Koshkarov, O.; Smolyakov, A. I.; Romadanov, I. V.; Chapurin, O.; Umansky, M. V.; Raitses, Y.; Kaganovich, I. D.
2018-01-01
The current flow in two-fluid plasma is inherently unstable if plasma components (e.g., electrons and ions) are in different collisionality regimes. A typical example is a partially magnetized E ×B plasma discharge supported by the energy released from the dissipation of the current in the direction of the applied electric field (perpendicular to the magnetic field). Ions are not magnetized so they respond to the fluctuations of the electric field ballistically on the inertial time scale. In contrast, the electron current in the direction of the applied electric field is dissipatively supported either by classical collisions or anomalous processes. The instability occurs due to a positive feedback between the electron and ion current coupled by the quasi-neutrality condition. The theory of this instability is further developed taking into account the electron inertia, finite Larmor radius and nonlinear effects. It is shown that this instability results in highly nonlinear quasi-coherent structures resembling breathing mode oscillations in Hall thrusters.
Parameter-free dissipation in simulated sliding friction
Benassi, A.; Vanossi, A.; Santoro, G. E.; Tosatti, E.
2010-08-01
Nonequilibrium molecular-dynamics simulations, of crucial importance in sliding friction, are hampered by arbitrariness and uncertainties in the way Joule heat is removed. We implement in a realistic frictional simulation a parameter-free, non-Markovian, stochastic dynamics, which, as expected from theory, absorbs Joule heat precisely as a semi-infinite harmonic substrate would. Simulating stick-slip friction of a slider over a two-dimensional Lennard-Jones solid, we compare our virtually exact frictional results with approximate ones from commonly adopted empirical dissipation schemes. While the latter are generally in serious error, we show that the exact results can be closely reproduced by a viscous Langevin dissipation at the boundary layer, once the backreflected frictional energy is variationally optimized.
Magnetic field dissipation and fractal model of current sheets
International Nuclear Information System (INIS)
Yankov, V.V.
1997-01-01
A model of magnetic field dissipation is suggested, which possesses features of both the Kolmogorov model of turbulence of ideal fluid and the Sweet endash Parker model of magnetic reconnection. It is suggested that current sheets are smooth along the magnetic lines but have fractal structure in the transverse dimension. The fractal dimension d=2.5 of the current sheet was found instead of d=3 in Kolmogorov-like models and d=2 in the Sweet endash Parker model. The reconnection time is the geometrical mean of the Alfvacute en time and the Sweet endash Parker time. The magnetic energy dissipation time can be even shorter, up to the Alfvacute en time. copyright 1997 American Institute of Physics
Lee, M. A.
1980-01-01
A recent paper by Wentzel, which claims to calculate a plasma heating rate due to dissipation of surface waves in an ideal magnetohydrodynamic (MHD) fluid, is found to be in error in interpretation. A well-established general theorem pertaining to the conservative ideal MHD fluid requires that the normal mode calculated by Wentzel be oscillatory in time. Within ideal MHD, dissipation and plasma heating are therefore impossible.