WorldWideScience

Sample records for energy deposition processes

  1. High energy high rate pulsed power processing of materials by powder consolidation and by railgun deposition

    Science.gov (United States)

    Persad, C.; Marcus, H. L.; Weldon, W. F.

    1987-03-01

    This exploratory research program was initiated to investigate the potential of using pulse power sources for powder consolidation, deposition and other High Energy High Rate Processing. The characteristics of the High Energy High Rate (1MJ/s) powder consolidation using megampere current pulses from a Homopolar Generator, have been defined. Molybdenum Alloy TZM, A Nickel based metallic glass, Copper graphite composites, and P/M Aluminum Alloy X7091 have been investigated. The powder consolidation process produced high densification rates. Density values of 80% to 99% could be obtained with sub second high temperature exposure. Specific energy input and applied pressure were controlling process parameters. Time Temperature Transformation (TTT) concepts underpin a fundamental understanding of pulsed power processing. Deposition experiments were conducted using an exploding foil device (EFD) providing an armature feed to railgun mounted in a vacuum chamber. The material to be deposited - in plasma, gas, liquid or solid state - was accelerated electromagnetically in the railgun and deposited on a substrate.

  2. Energy Deposition Processes in Titan's Upper Atmosphere and Its Induced Magnetosphere

    Science.gov (United States)

    Sittler, Edward C.; Hartle, R. E.; Bertucci, Cesar; Coates, Andrew; Cravens, Thomas; Dandouras, Iannis; Shemansky, Don

    Most of Titan's atmospheric organic and nitrogen chemistry, aerosol formation, and atmospheric loss are driven from external energy sources such as Solar UV, Saturn's magnetosphere, solar wind and galactic cosmic rays. The Solar UV tends to dominate the energy input at lower altitudes~1,200 km but which can extend down to ~400 km, while the plasma interaction from Saturn's magnetosphere, Saturn's magnetosheath or solar wind are more important at higher altitudes ~1,400 km, but the heavy ion plasma (O+) ~5 keV and energetic ions (H+) ~ 30 keV or higher from Saturn's magnetosphere can penetrate below 950 km. Cosmic rays with energies >1 GeV can penetrate much deeper into Titan's atmosphere with most of its energy deposited ~70 km altitude. Haze layers are observed in scattered solar photons starting at 510 km, but aerosols are broadly distributed and measured in extinction from 1,000 km downward, diffusively separated to 400 km. The induced magnetic field from Titan's interaction with the external plasma can be very complex and will tend to channel the flow of energy into Titan's upper atmosphere. Cassini observations combined with advanced hybrid simulations of the plasma interaction with Titan's upper atmosphere show significant changes in the character of the interaction with Saturn local time at Titan's orbit where the magnetosphere displays large and systematic changes with local time. The external solar wind can also drive sub-storms within the magnetosphere which can then modify the magnetospheric interaction with Titan. Another important parameter is solar zenith angle (SZA) with respect to the co-rotation direction of the magnetospheric flow which is referred to as the solar incidence-ram angle. Titan's interaction can contribute to atmospheric loss via pickup ion loss, scavenging of Titan's ionospheric plasma, loss of ionospheric plasma down its induced magnetotail via an ionospheric wind, and non-thermal loss of the atmosphere via heating and sputtering

  3. Physical Processes and Applications of the Monte Carlo Radiative Energy Deposition (MRED) Code

    Science.gov (United States)

    Reed, Robert A.; Weller, Robert A.; Mendenhall, Marcus H.; Fleetwood, Daniel M.; Warren, Kevin M.; Sierawski, Brian D.; King, Michael P.; Schrimpf, Ronald D.; Auden, Elizabeth C.

    2015-08-01

    MRED is a Python-language scriptable computer application that simulates radiation transport. It is the computational engine for the on-line tool CRÈME-MC. MRED is based on c++ code from Geant4 with additional Fortran components to simulate electron transport and nuclear reactions with high precision. We provide a detailed description of the structure of MRED and the implementation of the simulation of physical processes used to simulate radiation effects in electronic devices and circuits. Extensive discussion and references are provided that illustrate the validation of models used to implement specific simulations of relevant physical processes. Several applications of MRED are summarized that demonstrate its ability to predict and describe basic physical phenomena associated with irradiation of electronic circuits and devices. These include effects from single particle radiation (including both direct ionization and indirect ionization effects), dose enhancement effects, and displacement damage effects. MRED simulations have also helped to identify new single event upset mechanisms not previously observed by experiment, but since confirmed, including upsets due to muons and energetic electrons.

  4. High-energy high-rate pulsed-power processing of materials by powder consolidation and by railgun deposition. Technical report (Final), 10 April 1985-10 February 1987

    Energy Technology Data Exchange (ETDEWEB)

    Persad, C.; Marcus, H.L.; Weldon, W.F.

    1987-03-31

    This exploratory research program was initiated to investigate the potential of using pulse power sources for powder consolidation, deposition and other high-energy high-rate processing. The characteristics of the high-energy-high-rate (1MJ/s) powder consolidation using megampere current pulses from a homopolar generator, were defined. Molybdenum Alloy TZM, a nickel-based metallic glass, copper/graphite composites, and P/M aluminum alloy X7091 were investigated. The powder-consolidation process produced high densification rates. Density values of 80% to 99% could be obtained with subsecond high-temperature exposure. Specific energy input and applied pressure were controlling process parameters. Time temperature transformation (TTT) concepts underpin a fundamental understanding of pulsed power processing. Inherent control of energy input, and time-to-peak processing temperature developed to be held to short times. Deposition experiments were conducted using an exploding-foil device (EFD) providing an armature feed to railgun mounted in a vacuum chamber. The material to be deposited - in plasma, gas, liquid, or solid state - was accelerated electromagnetically in the railgun and deposited on a substrate. Deposits of a wide variety of single- and multi-specie materials were produced on several types of substrates. In a series of ancillary experiments, pulsed-skin-effect heating and self quenching of metallic conductors was discovered to be a new means of surface modification by high-energy high-rate-processing.

  5. Supersonic Flow Control Using Combined Energy Deposition

    Directory of Open Access Journals (Sweden)

    O. A. Azarova

    2015-03-01

    Full Text Available Drag force control via energy deposition in an oncoming flow is a wide area of interest in aerospace sciences. Recently, investigations on the effect of combining energy sources have been conducted. The possibility of coupling microwave (MW discharges or MW and laser energy deposition is discussed. In the present work, the flow details accompanying the interaction of a combined energy release and an aerodynamic body in a supersonic flow are considered numerically on the base of the Euler equations. Comparison with non-combined energy deposition is analyzed. The effect of introducing the internal part to the energy release on the drag force reduction is examined. The flows for blunt cylinder, hemisphere-cylinder and pointed body are considered for a wide class of the combined energy source characteristics. Freestream Mach number is varied from 1.89 to 3.45. Complicated unsteady vortex structures caused by the Richtmyer–Meshkov instabilities are shown to be the reason for the reduction in drag. The unsteady double vortex mechanism of the frontal drag force reduction and mechanism of the constantly acting vortices at the steady flow are described. Suppression of shear layer instability and large scaled flow pulsations as the result of the combined energy release effect is established. Complex conservative difference schemes are used in the simulations.

  6. GEANT4 simulation of electron energy deposition in extended media

    CERN Document Server

    Kadri, O; Gharbi, F; Trabelsi, A

    2007-01-01

    The present work demonstrates that GEANT4 yields a consistent description of electron transport processes in semi-infinite homogeneous and heterogeneous extended media. This comparison covers the e− energy deposition profiles in a range of elements from aluminum to tantalum through molybdenum at source energies from 0.3 to 1.0 MeV and at incident angles from 0° to 60°. The good agreement between simulation results and data confirms that the Monte Carlo used code is capable of accurate electron beam energy deposition calculation even under such conditions.

  7. An assessment of sediment-transport processes in the Lower Mekong River based on deposit grain sizes, the CM technique and flow-energy data

    Science.gov (United States)

    Bravard, Jean-Paul; Goichot, Marc; Tronchère, Hervé

    2014-02-01

    The Lower Mekong River has been an important research topic for at least 15 years, notably in the fields of hydrology, fluvial geomorphology, and the impact of dams. Recent papers refer mostly to the impact of the Lancang chain of hydroelectric dams constructed on the Chinese section of the river. Among the pending scientific questions are (1) the upstream-downstream variations in the concentration and yield of suspended sediment and (2) the relative importance of sand in the total yield. The general consensus among the scientific community is that the relative importance of sand in suspended load is not the main scientific concern despite its extensive presence in the Mekong River channel, as noted by geomorphologists, and despite its extreme importance for the stability of the delta shoreline in Viet Nam. This paper contradicts the general consensus. Its objective is to present new information on the processes of sand transport in the Lower Mekong channel. Imagery, field observations, sampling on the river banks, and grain size analysis of sand deposits have been carried out between Chiang Sean (downstream of the Chinese border) and the delta. The C-M image technique served to discriminate between the various transport processes (bedload and different types of suspension). This technique helps in understanding the changing processes responsible for downstream sediment transfer in river channels. The results of this study are the following.energy of floods. Energy helps to explain longitudinal variations in the relative importance of the different modes of transport and serves to distinguish between bedload

  8. Thermal energy storage in granular deposits

    Science.gov (United States)

    Ratuszny, Paweł

    2017-10-01

    Energy storage technology is crucial for the development of the use of renewable energy sources. This is a substantial constraint, however it can, to some extent, be solved by storing energy in its various forms: electrical, mechanical, chemical and thermal. This article presents the results of research in thermal properties of granular deposits. Correlation between temperature changes in the stores over a period of time and their physical properties has been studied. The results of the research have practical application in designing thermal stores based on bulk materials and ground deposits. Furthermore, the research results are significant for regeneration of the lower ground sources for heat pumps and provide data for designing ground heat exchangers for ventilation systems.

  9. Antidunes: new insights on processes and deposits

    Science.gov (United States)

    Leclair, Suzanne

    2014-05-01

    This talk presents :1) a brief review of the development of our understanding of antidune processes and deposits; 2) results from the author's current collaborative studies, and; 3) points out key issues to be addressed in future research on upper-regime bedforms and sedimentary structures. Antidunes deposits may be overlooked or incorrectly interpretated in the sedimentary record. In alongstream direction, their preserved sedimentary structures resemble dune trough-cross stratification while accros-stream sections show mostly planar beds. Antidune strata can be structureless, and hence similar to some chute-and-pool, or hydraulic-jumps deposits. Moreover, recognition of antidune stratification in nature may also be hampered by the spatial limitation of exposures compared to the scale of the formative bedforms. However, antidune signature presents internal distinctive stratal and textural features that were revealed by experimental investigation and observation in modern fluvial deposits. The main results come from the comparative image analysis of video records and photographs of sediment samples (sediment peels) from flume experiments with upper-stage, open-flow conditions. These results brough new insights on antidune migration processes and deposition /erosion sequences, allowing to revise the traditional model typically presented in texbooks. Differences do occur between deposition/erosion patterns of 'progresive' antidunes (not all antidunes break) and breaking antidunes, resulting in the (potential) preservation of spatially-limited strata with boundaries that define a sort of polygone within the overall deposits, and that can show 'clusters' of gravel (antidune signature may then be more apparent in sand-and-gravel sediment than in well-sorted sand). This specific sedimentary feature was obverved in modern deposits from a dryland river (where antidune can occur during flash floods). Otherwise, limited experimental data on submarine, super-critical , high

  10. Litigation in Perinatal Care: The Deposition Process.

    Science.gov (United States)

    Miller, Lisa A

    Litigation in perinatal nursing represents a disproportionate share of indemnity payouts and results in excessive psychological stress. Testimony at deposition or trial can be challenging for clinicians; little is taught in training or postgraduate education regarding litigation. Nurses, midwives, and physicians can effectively navigate the deposition process and prepare for trial testimony by understanding the plaintiff's goals, recognizing the role of documentation, and becoming familiar with various plaintiff's strategies including reptile theory. Knowledge of psychological concepts such as confirmation bias and cognitive dissonance may assist clinicians in responding to plaintiff's lines of questioning. Deposition preparation is crucial to the defense and requires active participation on the part of clinicians; it may include mock deposition or use of simulation laboratories. Common mistakes in deposition may be avoided with foresight and anticipatory planning by clinicians working closely with risk managers and defense attorneys. This article provides an overview of the deposition process, including the plaintiff's goals and common approaches, as well as the role of documentation and common errors of deponents.

  11. Optimization design of energy deposition on single expansion ramp nozzle

    Science.gov (United States)

    Ju, Shengjun; Yan, Chao; Wang, Xiaoyong; Qin, Yupei; Ye, Zhifei

    2017-11-01

    Optimization design has been widely used in the aerodynamic design process of scramjets. The single expansion ramp nozzle is an important component for scramjets to produces most of thrust force. A new concept of increasing the aerodynamics of the scramjet nozzle with energy deposition is presented. The essence of the method is to create a heated region in the inner flow field of the scramjet nozzle. In the current study, the two-dimensional coupled implicit compressible Reynolds Averaged Navier-Stokes and Menter's shear stress transport turbulence model have been applied to numerically simulate the flow fields of the single expansion ramp nozzle with and without energy deposition. The numerical results show that the proposal of energy deposition can be an effective method to increase force characteristics of the scramjet nozzle, the thrust coefficient CT increase by 6.94% and lift coefficient CN decrease by 26.89%. Further, the non-dominated sorting genetic algorithm coupled with the Radial Basis Function neural network surrogate model has been employed to determine optimum location and density of the energy deposition. The thrust coefficient CT and lift coefficient CN are selected as objective functions, and the sampling points are obtained numerically by using a Latin hypercube design method. The optimized thrust coefficient CT further increase by 1.94%, meanwhile, the optimized lift coefficient CN further decrease by 15.02% respectively. At the same time, the optimized performances are in good and reasonable agreement with the numerical predictions. The findings suggest that scramjet nozzle design and performance can benefit from the application of energy deposition.

  12. Energy deposition and K-shell ionization of supernovae

    Science.gov (United States)

    The, Lih-Sin; Bridgman, William T.; Clayton, Donald D.

    1994-01-01

    We present explicit evaluation of K-shell ionization caused by photoelectric absorption, by Compton scattering, and by electron collisions in supernovae envelopes. Each process derives from the radioactivity that dominates the bolometric luminosity of the model supernovae. We include the ionization by bremsstrahlung. We find that electron-collision ionization with decelerating Compton electrons is the dominant process of K-shell ionization for light elements (lighter than Si) whereas photoelectric K-shell absorption of Comptonized gammas is the dominant process of K-shell ionization for heavy elements (like Fe). The relative importance of the ionization processes also depends upon composition and upon time, as well as upon supernova type. For Type Ia all four ionization sources are of importance. We present fitting formulas for the deposition of radioactive power in each class of models studied. The energy deposition of all mechanisms decreases with time, including the rate of K-shell ionizations of all elements throughout the supernovae model evaluated herein. We compare the relative contributions to the energy deposition and confirm with greater numerical detail results already established.

  13. Imprint reduction in rotating heavy ions beam energy deposition

    Energy Technology Data Exchange (ETDEWEB)

    Bret, A., E-mail: antoineclaude.bret@uclm.es [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, MS-51, Cambridge, MA 02138 (United States); ETSI Industriales, Universidad Castilla-La Mancha, 13071 Ciudad Real (Spain); Instituto de Investigaciones Energéticas y Aplicaciones Industriales, Campus Universitario de Ciudad Real, 13071 Ciudad Real (Spain); Piriz, A.R., E-mail: Roberto.Piriz@uclm.es [ETSI Industriales, Universidad Castilla-La Mancha, 13071 Ciudad Real (Spain); Instituto de Investigaciones Energéticas y Aplicaciones Industriales, Campus Universitario de Ciudad Real, 13071 Ciudad Real (Spain); Tahir, N.A., E-mail: n.tahir@gsi.de [GSI Darmstadt, Plankstrasse 1, 64291 Darmstadt (Germany)

    2014-01-01

    The compression of a cylindrical target by a rotating heavy ions beam is contemplated in certain inertial fusion schemes or in heavy density matter experiments. Because the beam has its proper temporal profile, the energy deposition is asymmetric and leaves an imprint which can have important consequences for the rest of the process. In this paper, the Fourier components of the deposited ion density are computed exactly in terms of the beam temporal profile and its rotation frequency Ω. We show that for any beam profile of duration T, there exist an infinite number of values of ΩT canceling exactly any given harmonic. For the particular case of a parabolic profile, we find possible to cancel exactly the first harmonic and nearly cancel every other odd harmonics. In such case, the imprint amplitude is divided by 4 without any increase of Ω.

  14. Characteristics of deposition process of thin films by ion-beam evaporation

    Energy Technology Data Exchange (ETDEWEB)

    Kitayama, Shinji; Endo, Fumito; Suzuki, Tsuneo; Suematsu, Hisayuki; Jiang, Weihua; Yatsui, Kiyoshi [Nagoya Univ. of Technology, Extreme Energy-Density Research Inst., Nagaoka, Niigata (Japan)

    2002-06-01

    Intense pulsed ion-beam evaporation (IBE) has been proposed as one of the new techniques for the preparation of thin films. To understand the basic process of thin film deposition, the energy deposition on the substrate surface by ablation plasma was measured by using calorimetric technique. The characteristics of prepared thin films were studied with deposition energy. In addition, the substrate temperature was calculated, based on the experimental results, by using one-dimensional simulations only considering heat conduction. (author)

  15. Ionizing Energy Depositions After Fast Neutron Interactions in Silicon

    CERN Document Server

    Bergmann, Benedikt; Caicedo, Ivan; Kierstead, James; Takai, Helio; Frojdh, Erik

    2016-01-01

    In this study we present the ionizing energy depositions in a 300 μm thick silicon layer after fast neutron impact. With the Time-of-Flight (ToF) technique, the ionizing energy deposition spectra of recoil silicons and secondary charged particles were assigned to (quasi-)monoenergetic neutron energies in the range from 180 keV to hundreds of MeV. We show and interpret representative measured energy spectra. By separating the ionizing energy losses of the recoil silicon from energy depositions by products of nuclear reactions, the competition of ionizing (IEL) and non-ionizing energy losses (NIEL) of a recoil silicon within the silicon lattice was investigated. The data give supplementary information to the results of a previous measurement and are compared with different theoretical predictions.

  16. Ionizing Energy Depositions After Fast Neutron Interactions in Silicon

    Science.gov (United States)

    Bergmann, Benedikt; Pospisil, Stanislav; Caicedo, Ivan; Kierstead, James; Takai, Helio; Frojdh, Erik

    2016-08-01

    In this study we present the ionizing energy depositions in a 300 μm thick silicon layer after fast neutron impact. With the Time-of-Flight (ToF) technique, the ionizing energy deposition spectra of recoil silicons and secondary charged particles were assigned to (quasi-)monoenergetic neutron energies in the range from 180 keV to hundreds of MeV. We show and interpret representative measured energy spectra. By separating the ionizing energy losses of the recoil silicon from energy depositions by products of nuclear reactions, the competition of ionizing (IEL) and non-ionizing energy losses (NIEL) of a recoil silicon within the silicon lattice was investigated. The data give supplementary information to the results of a previous measurement and are compared with different theoretical predictions.

  17. Characteristics of Single-Track and Multi-track Depositions of Stellite by Micro-plasma Transferred Arc Powder Deposition Process

    Science.gov (United States)

    Sawant, Mayur S.; Jain, N. K.

    2017-08-01

    This paper describes the characteristics study of single-track and multi-track deposition of Stellite 6 on AISI 4130 steel substrate by indigenously developed micro-plasma transferred arc powder deposition (μ-PTAPD) process. Deposition height and width, dilution and microstructure have been used to characterize the single-track depositions by studying effects of micro-plasma power, travel speed of worktable and powder mass flow rate on energy consumption per unit traverse length and power consumption per unit powder mass flow rate. Micro-plasma power was found to be the most influential parameter that affects energy and deposition material consumption. Consequently, its influence on micro-hardness and abrasion resistance of multi-track deposition was studied. Results showed that increase in micro-plasma power decreases micro-hardness and scratch hardness number and increases mean value of friction coefficient. Comparison of microstructure and chemical composition of single-track and multi-track depositions revealed that single-track has finer dendritic microstructure than the multi-track deposition. The black colored matrix and white colored dendrites present in the multi-track deposition have higher wt.% of cobalt and less wt.% of chromium than the single-track deposition. Comparison of µ-PTAPD process capabilities with the existing processes for Stellite deposition establishes that it is an energy-efficient, cost-effective and good quality deposition yielding process.

  18. ENERGY EFFICIENT LAUNDRY PROCESS

    Energy Technology Data Exchange (ETDEWEB)

    Tim Richter

    2005-04-01

    With the rising cost of energy and increased concerns for pollution and greenhouse gas emissions from power generation, increased focus is being put on energy efficiency. This study looks at several approaches to reducing energy consumption in clothes care appliances by considering the appliances and laundry chemistry as a system, rather than individually.

  19. Ablation and deposition processes in carbon arc discharge for nanosynthesis

    Science.gov (United States)

    Raitses, Yevgeny; Ng, Jonathan; Nemchinsky, Valerian; Yeh, Yao-Wen; Gershman, Sophia; Vekselman, Vlad

    2015-09-01

    The anodic arc discharges with consumed anodes are used to produce various nanoparticles, including carbon nanotubes. Our experiments with the carbon arc at atmospheric pressure helium demonstrate the dependence of the anode ablation rate on the anode diameter, which cannot be explained by changes of the current density at the anode. In particular, the anode ablation rate for narrow graphite anodes is significantly enhanced resulting in high deposition rates of carbonaceous products on the copper cathode. The proposed model explains these results with interconnected steady-state models of the cathode and the anode processes. Results of experimental validation of this model are presented. This work was supported by U.S. Department of Energy, Office of Science, Basic Energy Sciences, Materials Sciences and Engineering Division.

  20. Energy deposition model for I-125 photon radiation in water

    Energy Technology Data Exchange (ETDEWEB)

    Fuss, M.C.; Garcia, G. [Instituto de Fisica Fundamental, Consejo Superior de Investigaciones Cientificas (CSIC), Madrid (Spain); Munoz, A.; Oller, J.C. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Madrid (Spain); Blanco, F. [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad Complutense de Madrid (Spain); Limao-Vieira, P. [Laboratorio de Colisoes Atomicas e Moleculares, Departamento de Fisica, CEFITEC, FCT-Universidade Nova de Lisboa, Caparica (Portugal); Williart, A.; Garcia, G. [Departamento de Fisica de los Materiales, Universidad Nacional de Educacion a Distancia, Madrid (Spain); Huerga, C.; Tellez, M. [Hospital Universitario La Paz, Madrid (Spain)

    2010-10-15

    In this study, an electron-tracking Monte Carlo algorithm developed by us is combined with established photon transport models in order to simulate all primary and secondary particle interactions in water for incident photon radiation. As input parameters for secondary electron interactions, electron scattering cross sections by water molecules and experimental energy loss spectra are used. With this simulation, the resulting energy deposition can be modelled at the molecular level, yielding detailed information about localization and type of single collision events. The experimental emission spectrum of I-125 seeds, as used for radiotherapy of different tumours, was used for studying the energy deposition in water when irradiating with this radionuclide. (authors)

  1. Microbiological processes in banded iron formation deposition

    DEFF Research Database (Denmark)

    Posth, Nicole R.; Konhauser, Kurt O.; Kappler, Andreas

    2013-01-01

    Banded iron formations have been studied for decades, particularly regarding their potential as archives of the Precambrian environment. In spite of this effort, the mechanism of their deposition and, specifically, the role that microbes played in the precipitation of banded iron formation minerals......, remains unresolved. Evidence of an anoxic Earth with only localized oxic areas until the Great Oxidation Event ca 2·45 to 2·32 Ga makes the investigation of O2-independent mechanisms for banded iron formation deposition relevant. Recent studies have explored the long-standing proposition that Archean...... banded iron formations may have been formed, and diagenetically modified, by anaerobic microbial metabolisms. These efforts encompass a wide array of approaches including isotope, ecophysiological and phylogeny studies, molecular and mineral marker analysis, and sedimentological reconstructions. Herein...

  2. influence of dietary energy concentration on protein deposition of ad ...

    African Journals Online (AJOL)

    This paper describes the rate and efficiency of protein deposition in pigs that were fed ad lib on diets with an adequate protein content, but with different energy con- centrations, using the Roux mathematical model (Roux,. 1976) to describe the data obtained from sequentially slaughtered pigs. Materials and Methods.

  3. Energy deposition from focused terawatt laser pulses in air

    CERN Document Server

    Point, Guillaume; Mysyrowicz, André; Houard, Aurélien

    2015-01-01

    Laser filamentation is responsible for the deposition of a significant part of the laser pulse energy in the propagation medium. We found that using terawatt laser pulses and relatively tight focusing conditions in air, resulting in a bundle of co-propagating multifilaments, more than 50 % of the pulses energy is transferred to the medium, eventually degrading into heat. This results in a strong hydrodynamic reaction of air with the generation of shock waves and associated underdense channels for each short-scale filament. In the focal zone, where filaments are close to each other, these discrete channels eventually merge to form a single cylindrical low-density tube over a $\\sim 1~ \\mu\\mathrm{s}$ timescale. We measured the maximum lineic deposited energy to be more than 1 J/m.

  4. Films deposited from reactive sputtering of aluminum acetylacetonate under low energy ion bombardment

    Energy Technology Data Exchange (ETDEWEB)

    Battaglin, Felipe Augusto Darriba; Prado, Eduardo Silva; Cruz, Nilson Cristino da; Rangel, Elidiane Cipriano, E-mail: elidiane@sorocaba.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Sorocaba, SP (Brazil). Lab. de Plasmas Tecnologicos; Caseli, Luciano [Universidade Federal de Sao Paulo (UNIFESP), Diadema, SP (Brazil). Instituto de Ciencias Ambientais, Quimicas e Farmaceuticas; Silva, Tiago Fiorini da; Tabacniks, Manfredo Harri [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

    2017-07-15

    Films were deposited from aluminum acetylacetonate (Al(acac)3 ) using a methodology involving reactive sputtering and low energy ion bombardment. The plasma was generated by the application of radiofrequency power to the powder containing electrode and simultaneously, negative pulses were supplied to the electrode where the substrates were attached. It was investigated the effect of the duty cycle of the pulses (Δ) on the properties of the coatings. Association of ion bombardment to the deposition process increased film thickness, structure reticulation and organic content. Ions from the deposition environment were implanted at the film-air interface or underneath it. Morphology and topography were altered depending on Δ. Considering the enhancement of Δ, it affected the flux of ions reaching the depositing interface and then the deposition rate, H content, crosslinking degree and surface microstructure. Alumina groups were detected in the infrared spectra, whereas the precipitation of amorphous alumina was confirmed by X-ray diffraction. (author)

  5. Energy and the laundry process

    Energy Technology Data Exchange (ETDEWEB)

    Levins, W.P.

    1980-04-01

    Energy usage in the residential laundry process is discussed. The various parts of the washing and drying cycles and areas where energy is being wasted or where its usage can be optimized are analyzed. The application of R and D to these areas will result in energy savings. The work was centered on standard and large-size automatic washers and dryers, as compact, portable, and manual models comprise a small part of the market. However, the principles discussed apply to them also. Data from many sources were used to compile this report. Most sources show very good general agreement so far as energy consumption and usage patterns are concerned. The results suggest that improved and/or integrated controls utilizing modern electronics can indeed help conserve energy. A better understanding by the consumer of the factors involved in the laundry process can also lead to the purchase and wise use of that laundry equipment which best suits the individual needs.

  6. Nanostructured Electrodes Via Electrostatic Spray Deposition for Energy Storage System

    KAUST Repository

    Chen, C.

    2014-10-02

    Energy storage systems such as Li-ion batteries and supercapacitors are extremely important in today’s society, and have been widely used as the energy and power sources for portable electronics, electrical vehicles and hybrid electrical vehicles. A lot of research has focused on improving their performance; however, many crucial challenges need to be addressed to obtain high performance electrode materials for further applications. Recently, the electrostatic spray deposition (ESD) technique has attracted great interest to satisfy the goals. Due to its many advantages, the ESD technique shows promising prospects compared to other conventional deposition techniques. In this paper, our recent research outcomes related to the ESD derived anodes for Li-ion batteries and other applications is summarized and discussed.

  7. Cold spray technology: future of coating deposition processes

    OpenAIRE

    S.B.S. Kalsi; Harminder Singh; Sidhu, T.S.

    2012-01-01

    Cold spray (CS) belongs to a wide family of thermal spray technology with the difference that it is a solid state process in which spray particles are deposited via supersonic velocity impact at a temperature much below the melting point of the spray material. This paper briefly describes the various aspects of this rapidly emerging technology, with almost all the important parameters which affect the deposition behavior along with advantages and limitations; applications and history of emerg...

  8. Micromorphology of modern tills in southwestern Spitsbergen – insights into depositional and post-depositional processes

    Directory of Open Access Journals (Sweden)

    Skolasińska Katarzyna

    2016-12-01

    Full Text Available Textural properties and microstructures are commonly used properties in the analysis of Pleistocene and older glacial deposits. However, contemporary glacial deposits are seldom studied, particularly in the context of post-depositional changes. This paper presents the results of a micromorphological study of recently deposited tills in the marginal zones of Hansbreen and Torellbreen, glaciers in southwestern Spitsbergen. The main objectives of this study were to compare modern tills deposited in subglacial and supraglacial conditions, as well as tills that were freshly released from ice with those laid down several decades ago. The investigated tills are primarily composed of large clasts of metamorphic rocks and represent coarse-grained, matrix-supported diamictons. The tills reveal several characteristic features for ductile (e.g. turbate structures and brittle (e.g. lineations, microshears deformations, which have been considered to be indicative of subglacial conditions. In supraglacial tills, the same structures are common as in the subglacial deposits, which points to the preservation of the primary features, though the sediment was transferred up to the glacier surface due to basal ice layer deformation and redeposited as slumps, or to formation of similar structures due to short-distance sediment re-deposition by mass flows. This study revealed that it might not be possible to distinguish subglacial and supraglacial tills on the basis of micromorphology if the latter are derived from a subglacial position. The only noted difference was the presence of iron oxide cementation zones and carbonate dissolution features in supraglacial tills. These features were found in tills that were deposited at least a few years ago and are interpreted to be induced by early post-depositional processes involving porewater/sediment interactions.

  9. Clean Fossil Energy Conversion Processes

    Science.gov (United States)

    Fan, L.-S.

    2007-03-01

    Absolute and per-capita energy consumption is bound to increase globally, leading to a projected increase in energy requirements of 50% by 2020. The primary source for providing a majority of the energy will continue to be fossil fuels. However, an array of enabling technologies needs to be proven for the realization of a zero emission power, fuel or chemical plants in the near future. Opportunities to develop new processes, driven by the regulatory requirements for the reduction or elimination of gaseous and particulate pollutant abound. This presentation describes the chemistry, reaction mechanisms, reactor design, system engineering, economics, and regulations that surround the utilization of clean coal energy. The presentation will cover the salient features of the fundamental and process aspects of the clean coal technologies in practice as well as in development. These technologies include those for the cleaning of SO2, H2S, NOx, and heavy metals, and separation of CO2 from the flue gas or the syngas. Further, new combustion and gasification processes based on the chemical looping concepts will be illustrated in the context of the looping particle design, process heat integration, energy conversion efficiency, and economics.

  10. Internal energy deposition into molecules upon positron-electron annihilation

    Energy Technology Data Exchange (ETDEWEB)

    Xu, J.; Hulett, L.D. Jr.; Lewis, T.A.; Donohue, D.L.; McLuckey, S.A.; Crawford, O.H. (Oak Ridge National Laboratory, P. O. Box 2008, Oak Ridge, Tennessee 37831 (United States))

    1994-05-01

    The dissociative ionization of organic molecules, induced by positrons having energies below the positronium threshold (0.5--3 eV), has been studied. Cross sections for the ionization-fragmentation processes increase as positron energies decrease. The data reveal that the energy required for dissociative ionization is supplied by the annihilation process, and that fragmentation occurs by breakage of C-C single bonds in preference to double and triple bonds.

  11. Recent Development of Advanced Electrode Materials by Atomic Layer Deposition for Electrochemical Energy Storage.

    Science.gov (United States)

    Guan, Cao; Wang, John

    2016-10-01

    Electrode materials play a decisive role in almost all electrochemical energy storage devices, determining their overall performance. Proper selection, design and fabrication of electrode materials have thus been regarded as one of the most critical steps in achieving high electrochemical energy storage performance. As an advanced nanotechnology for thin films and surfaces with conformal interfacial features and well controllable deposition thickness, atomic layer deposition (ALD) has been successfully developed for deposition and surface modification of electrode materials, where there are considerable issues of interfacial and surface chemistry at atomic and nanometer scale. In addition, ALD has shown great potential in construction of novel nanostructured active materials that otherwise can be hardly obtained by other processing techniques, such as those solution-based processing and chemical vapor deposition (CVD) techniques. This review focuses on the recent development of ALD for the design and delivery of advanced electrode materials in electrochemical energy storage devices, where typical examples will be highlighted and analyzed, and the merits and challenges of ALD for applications in energy storage will also be discussed.

  12. Ion - beam assisted process in the physical deposition of organic thin layers

    Energy Technology Data Exchange (ETDEWEB)

    Dimov, D; Spassova, E; Assa, J; Danev, G [Acad. J .Malinowski Central Laboratory of Photoprocesses, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl.109, 1113 Sofia (Bulgaria); Georgiev, A, E-mail: dean@clf.bas.b [University of Chemical Technology and Metallurgy, 8 Kl. Ohridski Blvd., 1756 Sofia (Bulgaria)

    2010-04-01

    A novel method was developed for physical deposition of thin polyimide layers by applying an argon plasma assisted process. The influence was investigated of the plasma on the combined molecular flux of the two thermally evaporated precursors - oxydianiline and pyromellitic dianhydride. The effects observed on the properties of the deposited films are explained with the increased energy of the precursor molecules resulting from the ion-molecular collisions. As could be expected, molecules with higher energy possess higher mobility and thus determine the modification of the films structure and their electrical properties.

  13. Energy bandgap variation in oblique angle-deposited indium tin oxide

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyurin; Kim, Hyunsoo; Cho, Jaehee, E-mail: jcho@chonbuk.ac.kr [School of Semiconductor and Chemical Engineering, Semiconductor Physics Research Center, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Park, Jun Hyuk; Kim, Jong Kyu [Department of Materials Science and Engineering, Pohang University of Science and Technology, Pohang 54896 (Korea, Republic of); Fred Schubert, E. [Future Chips Constellation, Department of Electrical, Computer, and Systems Engineering, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)

    2016-01-25

    Indium tin oxide (ITO) thin films deposited using the oblique angle deposition (OAD) technique exhibit a strong correlation between structural and optical properties, especially the optical bandgap energy. The microstructural properties of ITO thin films are strongly influenced by the tilt angle used during the OAD process. When changing the tilt angle, the refractive index, porosity, and optical bandgap energy of ITO films also change due to the existence of a preferential growth direction at the interface between ITO and the substrate. Experiments reveal that the ITO film's optical bandgap varies from 3.98 eV (at normal incident deposition) to 3.87 eV (at a 60° tilt angle)

  14. Monte Carlo Evaluation of Tritium Beta Spectrum Energy Deposition in Gallium Nitride (GaN) Direct Energy Conversion Devices

    Science.gov (United States)

    2014-09-01

    Monte Carlo Evaluation of Tritium Beta Spectrum Energy Deposition in Gallium Nitride (GaN) Direct Energy Conversion Devices by Marc Litz...MD 20783-1138 ARL-TR-7082 September 2014 Monte Carlo Evaluation of Tritium Beta Spectrum Energy Deposition in Gallium Nitride (GaN...Tritium Beta Spectrum Energy Deposition in Gallium Nitride (GaN) Direct Energy Conversion Devices 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM

  15. Energy deposition and charging in EUV lithography: Monte Carlo studies

    Science.gov (United States)

    Wiseheart, Liam; Narasimhan, Amrit; Grzeskowiak, Steven; Neisser, Mark; Ocola, Leonidas E.; Denbeaux, Greg; Brainard, Robert L.

    2016-03-01

    EUV photons expose photoresists by complex interactions including photoionization to create primary electrons (~80 eV), and subsequent ionization steps that create secondary electrons (10-60 eV). The mechanisms by which these electrons interact with resist components are key to optimizing the performance of EUV resists and EUV lithography as a whole. As these photoelectrons and secondary electrons are created, they deposit their energy within the resist, creating ionized atoms along the way. Because many photo- and secondary electrons can escape the resist through the surface, resists can become charged. Charging and energy deposition profiles within the resist may play a role in the sensitivity and line-edge roughness of EUV resists. In this paper, we present computational analysis of charging-influenced electron behavior in photoresists using LESiS (Low energy Electron Scattering in Solids), a software developed to understand and model electron-matter interactions. We discuss the implementation of charge and tracking and the model used to influence electron behavior. We also present the potential effects of charging on EUV and electron beam lithography by investigating secondary electron blur in charging and non-charging models.

  16. Cold spray technology: future of coating deposition processes

    Directory of Open Access Journals (Sweden)

    S.B.S. Kalsi

    2012-10-01

    Full Text Available Cold spray (CS belongs to a wide family of thermal spray technology with the difference that it is a solid state process in which spray particles are deposited via supersonic velocity impact at a temperature much below the melting point of the spray material. This paper briefly describes the various aspects of this rapidly emerging technology, with almost all the important parameters which affect the deposition behavior along with advantages and limitations; applications and history of emergence of this process is also reviewed. Though this technology emerges three decades ago but still it could not establish itself as viable practical industrial technology. Hence, the efforts, along with funding from public/private sources are required to commercialize this coating process. It is expected that next decade will saw the growth of cold spray as a viable coating process around the globe.

  17. Nuclear energy and process heating

    Energy Technology Data Exchange (ETDEWEB)

    Kozier, K.S

    1999-10-01

    Nuclear energy generated in fission reactors is a versatile commodity that can, in principle, satisfy any and all of mankind's energy needs through direct or indirect means. In addition to its dominant current use for electricity generation and, to a lesser degree, marine propulsion, nuclear energy can and has been used for process heat applications, such as space heating, industrial process heating and seawater desalination. Moreover, a wide variety of reactor designs has been employed to this end in a range of countries. From this spectrum of experience, two design approaches emerge for nuclear process heating (NPH): extracting a portion of the thermal energy from a nuclear power plant (NPP) (i.e., creating a combined heat and power, or CHP, plant) and transporting it to the user, or deploying dedicated nuclear heating plants (NHPs) in generally closer proximity to the thermal load. While the former approach is the basis for much of the current NPH experience, considerable recent interest exists for the latter, typically involving small, innovative reactor plants with enhanced and passive safety features. The high emphasis on inherent nuclear safety characteristics in these reactor designs reflects the need to avoid any requirement for evacuation of the public in the event of an accident, and the desire for sustained operation and investment protection at minimum cost. Since roughly 67% of mankind's primary energy usage is not in the form of electricity, a vast potential market for NPH systems exists, particularly at the low-to-moderate end-use temperatures required for residential space heating and several industrial applications. Although only About 0.5% of global nuclear energy production is presently used for NPH applications, an expanded role in the 21st century seems inevitable, in part, as a measure to reduce greenhouse gas emissions and improve air quality. While the technical aspects of many NPH applications are considered to be well proven, a

  18. A Modified Surface on Titanium Deposited by a Blasting Process

    Directory of Open Access Journals (Sweden)

    Caroline O’Sullivan

    2011-09-01

    Full Text Available Hydroxyapatite (HA coating of hard tissue implants is widely employed for its biocompatible and osteoconductive properties as well as its improved mechanical properties. Plasma technology is the principal deposition process for coating HA on bioactive metals for this application. However, thermal decomposition of HA can occur during the plasma deposition process, resulting in coating variability in terms of purity, uniformity and crystallinity, which can lead to implant failure caused by aseptic loosening. In this study, CoBlastTM, a novel blasting process has been used to successfully modify a titanium (V substrate with a HA treatment using a dopant/abrasive regime. The impact of a series of apatitic abrasives under the trade name MCD, was investigated to determine the effect of abrasive particle size on the surface properties of both microblast (abrasive only and CoBlast (HA/abrasive treatments. The resultant HA treated substrates were compared to substrates treated with abrasive only (microblasted and an untreated Ti. The HA powder, apatitic abrasives and the treated substrates were characterized for chemical composition, coating coverage, crystallinity and topography including surface roughness. The results show that the surface roughness of the HA blasted modification was affected by the particle size of the apatitic abrasives used. The CoBlast process did not alter the chemistry of the crystalline HA during deposition. Cell proliferation on the HA surface was also assessed, which demonstrated enhanced osteo-viability compared to the microblast and blank Ti. This study demonstrates the ability of the CoBlast process to deposit HA coatings with a range of surface properties onto Ti substrates. The ability of the CoBlast technology to offer diversity in modifying surface topography offers exciting new prospects in tailoring the properties of medical devices for applications ranging from dental to orthopedic settings.

  19. Additive Manufacturing of AlSi10Mg Alloy Using Direct Energy Deposition: Microstructure and Hardness Characterization

    Science.gov (United States)

    Javidani, M.; Arreguin-Zavala, J.; Danovitch, J.; Tian, Y.; Brochu, M.

    2017-04-01

    This paper aims to study the manufacturing of the AlSi10Mg alloy with direct energy deposition (DED) process. Following fabrication, the macro- and microstructural evolution of the as-processed specimens was initially investigated using optical microscopy and scanning electron microscopy. Columnar dendritic structure was the dominant solidification feature of the deposit; nevertheless, detailed microstructural analysis revealed cellular morphology near the substrate and equiaxed dendrites at the top end of the deposit. Moreover, the microstructural morphology in the melt pool boundary of the deposit differed from the one in the core of the layers. The remaining porosity of the deposit was evaluated by Archimedes' principle and by image analysis of the polished surface. Crystallographic texture in the deposit was also assessed using electron backscatter diffraction and x-ray diffraction analysis. The dendrites were unidirectionally oriented at an angle of 80° to the substrate. EPMA line scans were performed to evaluate the compositional variation and elemental segregation in different locations. Eventually, microhardness (HV) tests were conducted in order to study the hardness gradient in the as-DED-processed specimen along the deposition direction. The presented results, which exhibited a deposit with an almost defect free structure, indicate that the DED process can suitable for the deposition of Al-Si-based alloys with a highly consolidated structure.

  20. Photon beam convolution using polyenergetic energy deposition kernels.

    Science.gov (United States)

    Hoban, P W; Murray, D C; Round, W H

    1994-04-01

    In photon beam convolution calculations where polyenergetic energy deposition kernels (EDKS) are used, the primary photon energy spectrum should be correctly accounted for in Monte Carlo generation of EDKS. This requires the probability of interaction, determined by the linear attenuation coefficient, mu, to be taken into account when primary photon interactions are forced to occur at the EDK origin. The use of primary and scattered EDKS generated with a fixed photon spectrum can give rise to an error in the dose calculation due to neglecting the effects of beam hardening with depth. The proportion of primary photon energy that is transferred to secondary electrons increases with depth of interaction, due to the increase in the ratio mu ab/mu as the beam hardens. Convolution depth-dose curves calculated using polyenergetic EDKS generated for the primary photon spectra which exist at depths of 0, 20 and 40 cm in water, show a fall-off which is too steep when compared with EGS4 Monte Carlo results. A beam hardening correction factor applied to primary and scattered 0 cm EDKS, based on the ratio of kerma to terma at each depth, gives primary, scattered and total dose in good agreement with Monte Carlo results.

  1. Fluka Energy Deposition Studies for the HL LHC

    CERN Document Server

    Esposito, L S; Todesco, E

    2013-01-01

    The LHC upgrade, planned in about ten years from now, is envisaged to accumulate up to 3000 fb−1 integrated luminosity by running at a peak luminosity of 5×1034 cm−2 s−1 [1]. In order to reach such an ambitious goal, the high luminosity insertions need a major redesign implying a 150 mm aperture low-beta Inner Triplet (IT), a superconducting D1 and new quadrupoles in the Matching Section. Energy deposition studies show that degradation of the coil insulator represents the most challenging issue from the radiation impact point of view. We propose a suitable shielding consisting of a beam screen with several mm tungsten absorbers at mid-planes to guarantee not to exceed a few ten MGy. This will also allow a good margin with respect to the risk of radiation induced quenches.

  2. Energy deposition model based on electron scattering cross section data from water molecules

    Energy Technology Data Exchange (ETDEWEB)

    Munoz, A; Oiler, J C [Centra de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avenida Complutense 22, 28040 Madrid (Spain); Blanco, F [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad Complutense de Madrid, Avenida Complutense s.n., 28040 Madrid (Spain); Gorfinkiel, J D [Department of Physiscs and Astronomy, The Open University, Walton Hall, Milton Keynes MK7 6AA (United Kingdom); Limao-Vieira, P [Departamento de Fisica, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Maira-Vidal, A; Borge, M J G; Tengblad, O [Instituto de Estructura de la Materia, Consejo Superior de Investigaciones Cientificas (CSIC), Serrano 113-bis, 28006 Madrid, Spam (Spain); Huerga, C; Tellez, M [Hospital Universitario La Paz, paseo de la Castellana 261, 28046 Madrid (Spain); Garcia, G [Instituto de Matematicas y Fisica Fundamental, Consejo Superior de Investigaciones CientifIcas (CSIC), Serrano 113-bis, 28006 Madrid (Spain)], E-mail: g.garcia@imaff.cfmac.csic.es

    2008-10-01

    A complete set of electrons scattering cross sections by water molecules over a broad energy range, from the me V to the Me V ranges, is presented in this study. These data have been obtained by combining experiments and calculations and cover most relevant processes, both elastic and inelastic, which can take place in the considered energy range. A new Monte Carlo simulation programme has been developed using as input parameter these cross sectional data as well as experimental energy loss spectra. The simulation procedure has been applied to obtain electron tracks and energy deposition plots in water when irradiated by a Ru-106 plaque as those used for brachytherapy of ocular tumours. Finally, the low energy electron tracks provided by the present model have been compared with those obtained with other codes available in the literature.

  3. Energy deposition of heavy ions in the regime of strong beam-plasma correlations.

    Science.gov (United States)

    Gericke, D O; Schlanges, M

    2003-03-01

    The energy loss of highly charged ions in dense plasmas is investigated. The applied model includes strong beam-plasma correlation via a quantum T-matrix treatment of the cross sections. Dynamic screening effects are modeled by using a Debye-like potential with a velocity dependent screening length that guarantees the known low and high beam velocity limits. It is shown that this phenomenological model is in good agreement with simulation data up to very high beam-plasma coupling. An analysis of the stopping process shows considerably longer ranges and a less localized energy deposition if strong coupling is treated properly.

  4. Energy deposition study of low-energy cosmic radiation at sea level

    Science.gov (United States)

    Wijesinghe, Pushpa

    In this dissertation work, a computer simulation model based on the Geant4 simulation package has been designed and developed to study the energy deposition and track structures of cosmic muons and their secondary electrons in tissue-like materials. The particle interactions in a cubic water volume were first simulated. To analyze the energy deposition and tracks in small structures, with the intention of studying the energy localization in nanometric structures such as DNA, the chamber was sliced in three dimentions. Validation studies have been performed by comparing the results with experimental, theoretical, and other simulation results to test the accuracy of the simulation model. A human body phantom in sea-level muon environment was modeled to measure the yearly dose to a human from cosmic muons. The yearly dose in this phantom is about 22 millirems. This is close to the accepted value for the yearly dose from cosmic radiation at sea level. Shielding cosmic muons with a concrete slab from 0 to 2 meters increased the dose received by the body. This dissertation presents an extensive study on the interactions of secondary electrons created by muons in water. Index words. Radiation Dosimetry Simulation, Track Structures, Sea-Level muon Flux, Energy Deposition

  5. Ion mass and energy selective hyperthermal ion-beam assisted deposition setup

    Science.gov (United States)

    Gerlach, J. W.; Schumacher, P.; Mensing, M.; Rauschenbach, S.; Cermak, I.; Rauschenbach, B.

    2017-06-01

    For the synthesis of high-quality thin films, ion-beam assisted deposition (IBAD) is a frequently used technique providing precise control over several substantial film properties. IBAD typically relies on the use of a broad-beam ion source. Such ion sources suffer from the limitation that they deliver a blend of ions with different ion masses, each of them possessing a certain distribution of kinetic energy. In this paper, a compact experimental setup is presented that enables the separate control of ion mass and ion kinetic energy in the region of hyperthermal energies (few 1 eV - few 100 eV). This ion energy region is of increasing interest not only for ion-assisted film growth but also for the wide field of preparative mass spectrometry. The setup consists of a constricted glow-discharge plasma beam source and a tailor-made, compact quadrupole system equipped with entry and exit ion optics. It is demonstrated that the separation of monoatomic and polyatomic nitrogen ions (N+ and N2+) is accomplished. For both ion species, the kinetic energy is shown to be selectable in the region of hyperthermal energies. At the sample position, ion current densities are found to be in the order of 1 μA/cm2 and the full width at half maximum of the ion beam profile is in the order of 10 mm. Thus, the requirements for homogeneous deposition processes in sufficiently short periods of time are fulfilled. Finally, employing the described setup, for the first time in practice epitaxial GaN films were deposited. This opens up the opportunity to fundamentally study the influence of the simultaneous irradiation with hyperthermal ions on the thin film growth in IBAD processes and to increase the flexibility of the technique.

  6. A discrete element based simulation framework to investigate particulate spray deposition processes

    KAUST Repository

    Mukherjee, Debanjan

    2015-06-01

    © 2015 Elsevier Inc. This work presents a computer simulation framework based on discrete element method to analyze manufacturing processes that comprise a loosely flowing stream of particles in a carrier fluid being deposited on a target surface. The individual particulate dynamics under the combined action of particle collisions, fluid-particle interactions, particle-surface contact and adhesive interactions is simulated, and aggregated to obtain global system behavior. A model for deposition which incorporates the effect of surface energy, impact velocity and particle size, is developed. The fluid-particle interaction is modeled using appropriate spray nozzle gas velocity distributions and a one-way coupling between the phases. It is found that the particle response times and the release velocity distribution of particles have a combined effect on inter-particle collisions during the flow along the spray. It is also found that resolution of the particulate collisions close to the target surface plays an important role in characterizing the trends in the deposit pattern. Analysis of the deposit pattern using metrics defined from the particle distribution on the target surface is provided to characterize the deposition efficiency, deposit size, and scatter due to collisions.

  7. A Metallurgical Investigation of the Direct Energy Deposition Surface Repair of Ferrous Alloys

    Science.gov (United States)

    Marya, Manuel; Singh, Virendra; Hascoet, Jean-Yves; Marya, Surendar

    2018-01-01

    Among additive manufacturing (AM) processes, the direct energy deposition (DED) by laser is explored to establish its applicability for the repair of ferrous alloys such as UNS G41400 low-alloy steel, UNS S41000 martensitic stainless steel, UNS S17400 precipitation-strengthened martensitic stainless steel, and UNS S32750 super-duplex stainless steel. Unlike plating, thermal spray, and conventional cladding weld, DED laser powder deposition offers potential advantages, e.g., thin deposits, limited dilutions, narrow heat-affected zones (HAZ), potentially improved surface properties. In this investigation, all AM deposits were completed with an IREPA CLAD™ system using a powder feed of UNS N06625, an alloy largely selected for its outstanding corrosion resistance. This investigation first addresses topological aspects of AM deposits (including visual imperfections) before focusing on changes in microstructure, microhardness, chemical composition across AM deposits and base materials. It has been established that dense, uniform, hard ( 300 HVN), crack-free UNS N06625-compliant AM deposits of fine dendritic microstructures are reliably produced. However, except for the UNS S32750 steel, a significant martensitic hardening was observed in the HAZs of UNS G41400 ( 650 HVN), UNS S41000 ( 500 HVN), and UNS S17400 ( 370 HVN). In summary, this investigation demonstrates that the DED laser repair of ferrous parts with UNS N06625 may restore damaged surfaces, but it also calls for cautions and complementary investigations for alloys experiencing a high HAZ hardening, for which industry standard recommendations are exceeded and lead to an increased risk of delayed cracking in corrosive environments.

  8. Ion assisted deposition with low-energy ions for applications in modern optics

    CERN Document Server

    Kennedy, M

    1999-01-01

    realised by a process adaptation with UV-absorbing films. A further focal point are antireflective coatings on alkali halides optics for high-power CO sub 2 -lasers. Ion assisted deposition of NaF-films at extremely low ion energies (E sub i sub o sub n approx 5 eV) qualifies antireflective coatings with minimal absorption (alpha approx 1.5 cm sup - sup 1), high short-pulse damage threshold (50%-LIDT approx 60J/cm sup 2) and improved degradational stability. Main objective of this work is the development of ion assisted deposition processes without additional substrate heating for applications in precision and laser optics. New low-energy ion sources with ion energies below 100 eV were employed for the research work. Starting point of the process development are basic investigations on the ion assisted evaporation of fluoride and oxide thin film materials. The optimisation of the coating processes is primary done with the help of optical characterisation methods (spectral photometry, laser calorimetry, measur...

  9. Energy transfer processes in solar energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Fayer, M.D.

    1986-11-01

    By combining picosecond optical experiments and detailed statistical mechanics theory we continue to increase our understanding of the complex interplay of structure and dynamics in important energy transfer situations. A number of different types of problems will be focused on experimentally and theoretically. They are excitation transport among chromophores attached to finite size polymer coils; excitation transport among chromophores in monolayers, bilayers, and finite and infinite stacks of layers; excitation transport in large vesicle systems; and photoinduced electron transfer in glasses and liquids, focusing particularly on the back transfer of the electron from the photogenerated radical anion to the radical cation. 33 refs., 13 figs.

  10. Vapor-deposited porous films for energy conversion

    Science.gov (United States)

    Jankowski, Alan F.; Hayes, Jeffrey P.; Morse, Jeffrey D.

    2005-07-05

    Metallic films are grown with a "spongelike" morphology in the as-deposited condition using planar magnetron sputtering. The morphology of the deposit is characterized by metallic continuity in three dimensions with continuous and open porosity on the submicron scale. The stabilization of the spongelike morphology is found over a limited range of the sputter deposition parameters, that is, of working gas pressure and substrate temperature. This spongelike morphology is an extension of the features as generally represented in the classic zone models of growth for physical vapor deposits. Nickel coatings were deposited with working gas pressures up 4 Pa and for substrate temperatures up to 1000 K. The morphology of the deposits is examined in plan and in cross section views with scanning electron microscopy (SEM). The parametric range of gas pressure and substrate temperature (relative to absolute melt point) under which the spongelike metal deposits are produced appear universal for other metals including gold, silver, and aluminum.

  11. Processing Parameters Optimization for Material Deposition Efficiency in Laser Metal Deposited Titanium Alloy

    Science.gov (United States)

    Mahamood, Rasheedat M.; Akinlabi, Esther T.

    2016-03-01

    Ti6Al4V is an important Titanium alloy that is mostly used in many applications such as: aerospace, petrochemical and medicine. The excellent corrosion resistance property, the high strength to weight ratio and the retention of properties at high temperature makes them to be favoured in most applications. The high cost of Titanium and its alloys makes their use to be prohibitive in some applications. Ti6Al4V can be cladded on a less expensive material such as steel, thereby reducing cost and providing excellent properties. Laser Metal Deposition (LMD) process, an additive manufacturing process is capable of producing complex part directly from the 3-D CAD model of the part and it also has the capability of handling multiple materials. Processing parameters play an important role in LMD process and in order to achieve desired results at a minimum cost, then the processing parameters need to be properly controlled. This paper investigates the role of processing parameters: laser power, scanning speed, powder flow rate and gas flow rate, on the material utilization efficiency in laser metal deposited Ti6Al4V. A two-level full factorial design of experiment was used in this investigation, to be able to understand the processing parameters that are most significant as well as the interactions among these processing parameters. Four process parameters were used, each with upper and lower settings which results in a combination of sixteen experiments. The laser power settings used was 1.8 and 3 kW, the scanning speed was 0.05 and 0.1 m/s, the powder flow rate was 2 and 4 g/min and the gas flow rate was 2 and 4 l/min. The experiments were designed and analyzed using Design Expert 8 software. The software was used to generate the optimized process parameters which were found to be laser power of 3.2 kW, scanning speed of 0.06 m/s, powder flow rate of 2 g/min and gas flow rate of 3 l/min.

  12. Evaluation of Mineral Deposits Along the Little Wind River, Riverton, WY, Processing Site

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, Sam [Navarro Research and Engineering, Oak Ridge, TN (United States); Dam, Wiliam [US Department of Energy, Washington, DC (United States). Office of Legacy Management

    2014-12-01

    In 2012, the U.S.Department of Energy (DOE) began reassessing the former Riverton, Wyoming, Processing Site area for potential contaminant sources impacting groundwater. A flood in 2010 along the Little Wind River resulted in increases in groundwater contamination (DOE 2013).This investigation is a small part of continued efforts by DOE and other stakeholders to update human health and ecological risk assessments, to make a comprehensive examination of all exposure pathways to ensure that the site remains protective through established institutional controls. During field inspections at the Riverton Site in 2013, a white evaporitic mineral deposit was identified along the bank of the Little Wind River within the discharge zone of the groundwater contamination plume. In December 2013, Savannah River National Laboratory (SRNL) personnel collected a sample for analysis by X-ray fluorescence (Figure 1 shows the type of material sampled). The sample had a uranium concentration of approximately 64 to 73 parts per million. Although the uranium in this mineral deposit is within the expected range for evaporatic minerals in the western United States (SRNL 2014), DOE determined that additional assessment of the mineral deposit was warranted. In response to the initial collection and analysis of a sample of the mineral deposit, DOE developed a work plan (Work Plan to Sample Mineral Deposits Along the Little Wind River, Riverton, Wyoming, Processing Site [DOE 2014]) to further define the extent of these mineral deposits and the concentration of the associated contaminants (Appendix A). The work plan addressed field reconnaissance, mapping, sampling, and the assessment of risk associated with the mineral deposits adjacent to the Little Wind River.

  13. High Throughput Atomic Layer Deposition Processes: High Pressure Operations, New Reactor Designs, and Novel Metal Processing

    Science.gov (United States)

    Mousa, MoatazBellah Mahmoud

    Atomic Layer Deposition (ALD) is a vapor phase nano-coating process that deposits very uniform and conformal thin film materials with sub-angstrom level thickness control on various substrates. These unique properties made ALD a platform technology for numerous products and applications. However, most of these applications are limited to the lab scale due to the low process throughput relative to the other deposition techniques, which hinders its industrial adoption. In addition to the low throughput, the process development for certain applications usually faces other obstacles, such as: a required new processing mode (e.g., batch vs continuous) or process conditions (e.g., low temperature), absence of an appropriate reactor design for a specific substrate and sometimes the lack of a suitable chemistry. This dissertation studies different aspects of ALD process development for prospect applications in the semiconductor, textiles, and battery industries, as well as novel organic-inorganic hybrid materials. The investigation of a high pressure, low temperature ALD process for metal oxides deposition using multiple process chemistry revealed the vital importance of the gas velocity over the substrate to achieve fast depositions at these challenging processing conditions. Also in this work, two unique high throughput ALD reactor designs are reported. The first is a continuous roll-to-roll ALD reactor for ultra-fast coatings on porous, flexible substrates with very high surface area. While the second reactor is an ALD delivery head that allows for in loco ALD coatings that can be executed under ambient conditions (even outdoors) on large surfaces while still maintaining very high deposition rates. As a proof of concept, part of a parked automobile window was coated using the ALD delivery head. Another process development shown herein is the improvement achieved in the selective synthesis of organic-inorganic materials using an ALD based process called sequential vapor

  14. Sensing for directed energy deposition and powder bed fusion additive manufacturing at Penn State University

    Science.gov (United States)

    Nassar, Abdalla R.; Reutzel, Edward W.; Brown, Stephen W.; Morgan, John P.; Morgan, Jacob P.; Natale, Donald J.; Tutwiler, Rick L.; Feck, David P.; Banks, Jeffery C.

    2016-04-01

    Additive manufacturing of metal components through directed energy deposition or powder bed fusion is a complex undertaking, often involving hundreds or thousands of individual laser deposits. During processing, conditions may fluctuate, e.g. material feed rate, beam power, surrounding gas composition, local and global temperature, build geometry, etc., leading to unintended variations in final part geometry, microstructure and properties. To assess or control as-deposited quality, researchers have used a variety of methods, including those based on sensing of melt pool and plume emission characteristics, characteristics of powder application, and layer-wise imaging. Here, a summary of ongoing process monitoring activities at Penn State is provided, along with a discussion of recent advancements in the area of layer-wise image acquisition and analysis during powder bed fusion processing. Specifically, methods that enable direct comparisons of CAD model, build images, and 3D micro-tomographic scan data will be covered, along with thoughts on how such analyses can be related to overall process quality.

  15. Thermal energy management process experiment

    Science.gov (United States)

    Ollendorf, S.

    1984-01-01

    The thermal energy management processes experiment (TEMP) will demonstrate that through the use of two-phase flow technology, thermal systems can be significantly enhanced by increasing heat transport capabilities at reduced power consumption while operating within narrow temperature limits. It has been noted that such phenomena as excess fluid puddling, priming, stratification, and surface tension effects all tend to mask the performance of two-phase flow systems in a 1-g field. The flight experiment approach would be to attack the experiment to an appropriate mounting surface with a 15 to 20 meter effective length and provide a heat input and output station in the form of heaters and a radiator. Using environmental data, the size, location, and orientation of the experiment can be optimized. The approach would be to provide a self-contained panel and mount it to the STEP through a frame. A small electronics package would be developed to interface with the STEP avionics for command and data handling. During the flight, heaters on the evaporator will be exercised to determine performance. Flight data will be evaluated against the ground tests to determine any anomalous behavior.

  16. Research on Glass Frit Deposition Based on the Electrospray Process

    Directory of Open Access Journals (Sweden)

    Yifang Liu

    2016-04-01

    Full Text Available In this paper, the electrospray technology is used to easily deposit the glass frit into patterns at a micro-scale level. First, far-field electrospray process was carried out with a mixture of glass frit in the presence of ethanol. A uniform, smooth, and dense glass frit film was obtained, verifying that the electrospray technology was feasible. Then, the distance between the nozzle and the substrate was reduced to 2 mm to carry out near-field electrospray. The experimental process was improved by setting the range of the feed rate of the substrate to match both the concentration and the flow rate of the solution. Spray diameter could be less at the voltage of 2 kV, in which the glass frit film was expected to reach the minimum line width. A uniform glass frit film with a line width within the range of 400–500 μm was prepared when the speed of the substrate was 25 mm/s. It indicates that electrospray is an efficient technique for the patterned deposition of glass frit in wafer-level hermetic encapsulation.

  17. Deposits on heat exchanging surfaces, causes in the bleaching process and countermeasures; Belaeggningar paa vaermevaexlare, orsaker i blekprocessen och aatgaerder

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Staahl, Charlotte; Widell, Lars [AaF-Celpap AB, Stockholm (Sweden)

    2003-06-01

    Energy conservation in process industry implies to a large extent recovery of heat (or cold) from a process stream and its utilization for another process stream. The savings of energy that can be achieved depend on the process streams, but also on the efficiency of the heat exchange. A small driving temperature difference is a condition for an extensive recovery and a satisfactory preservation of its quality, i.e. its temperature. As process streams contain compounds or components that can precipitate and form deposits on heat exchanging surfaces, the recovery of heat is degraded. In the pulp and paper industry, two trends combine to increase the extent of fouling: a larger degree of closure for the process and a change in pH-profile caused by a switch to elementary chlorine free bleaching. In this study, the occurrence of deposits has been investigated for the mills that produce mechanical pulp and for the fiber line in mills producing chemical pulp. Deposits on the evaporator surfaces are treated in a parallel study. Except for some plants, deposits are not an important problem today. That does not mean that there has not been any problem or that problems will not occur. The origin of deposits lies in the chemistry of the process, but deposits have consequences for the thermal energy management. A list of possible actions in order to avoid deposits or to mitigate their consequences has been dressed in this report. They should be considered with the following order of priority: avoiding that the compounds that may form deposits enter at all the process, section 6.1; avoiding that these compounds form a deposit once they have entered the process, section 6.2; cleaning if nothing else helps or costs too much, section 6.3. Some of these methods are well known or are conventional changes in the processes. Some of these methods are less well proven or less well documented. In a longer time perspective, the kidney technology that is being developed could contribute to

  18. Measuring the extent and width of internal energy deposition in ion activation using nanocalorimetry.

    Science.gov (United States)

    Donald, William A; Williams, Evan R

    2010-04-01

    The recombination energies resulting from electron capture by a positive ion can be accurately measured using hydrated ion nanocalorimetry in which the internal energy deposition is obtained from the number of water molecules lost from the reduced cluster. The width of the product ion distribution in these experiments is predominantly attributable to the distribution of energy that partitions into the translational and rotational modes of the water molecules that are lost. These results are consistent with a singular value for the recombination energy. For large clusters, the width of the energy distribution is consistent with rapid energy partitioning into internal vibrational modes. For some smaller clusters with high recombination energies, the measured product ion distribution is narrower than that calculated with a statistical model. These results indicate that initial water molecule loss occurs on the time scale of, or faster than energy randomization. This could be due to inherently slow internal conversion or it could be due to a multi-step process, such as initial ion-electron pair formation followed by reduction of the ion in the cluster. These results provide additional evidence for the accuracy with which condensed phase thermochemical values can be deduced from gaseous nanocalorimetry experiments. 2010 American Society for Mass Spectrometry. Published by Elsevier Inc. All rights reserved.

  19. Time-specific measurements of energy deposition from radiation fields in simulated sub-micron tissue volumes

    Energy Technology Data Exchange (ETDEWEB)

    Famiano, M.A.

    1997-07-07

    A tissue-equivalent spherical proportional counter is used with a modified amplifier system to measure specific energy deposited from a uniform radiation field for short periods of time ({approximately}1 {micro}s to seconds) in order to extrapolate to dose in sub-micron tissue volumes. The energy deposited during these time intervals is compared to biological repair processes occurring within the same intervals after the initial energy deposition. The signal is integrated over a variable collection time which is adjusted with a square-wave pulse. Charge from particle passages is collected on the anode during the period in which the integrator is triggered, and the signal decays quickly to zero after the integrator feedback switch resets; the process repeats for every triggering pulse. Measurements of energy deposited from x rays, {sup 137}Cs gamma rays, and electrons from a {sup 90}Sr/{sup 90}Y source for various time intervals are taken. Spectral characteristics as a function of charge collection time are observed and frequency plots of specific energy and collection time-interval are presented. In addition, a threshold energy flux is selected for each radiation type at which the formation of radicals (based on current measurements) in mammalian cells equals the rate at which radicals are repaired.

  20. Erosion and deposition processes in surface granular flows

    Science.gov (United States)

    Trinh, T.; Boltenhagen, P.; Delannay, R.; Valance, A.

    2017-10-01

    We report on experiments aiming at characterizing erosion and deposition processes on a tilted granular bed. We investigate the existence of the neutral angle, that is, the critical angle at which erosion exactly balances accretion after the passage of a granular avalanche of a finite mass. Experiments show in particular that the neutral angle depends on both avalanche mass and shape but is rather insensitive to the bed length. This result strongly suggests that the effective friction between the static and mobile granular phases cannot be taken as an intrinsic property that is only material dependent but should be considered a flow-dependent property. Interestingly, for a given avalanche mass, the net erosion rate increases linearly with the angular deviation from the neutral angle. We also compare our data with the predictions of the erosion-deposition model introduced by Bouchaud, Cates, Ravi Prakash, and Edwards (BCRE) [J. Phys. I 4, 1283 (1994), 10.1051/jp1:1994195]. We show that the predictions drawn from the modified version of the BCRE model proposed by Boutreux and de Gennes, in which the local erosion rate between the static and mobile phases is independent of the flow thickness, are in remarkable agreement with the experimental results.

  1. Effects of Energy Deposition Characteristics on Localised Forced Ignition of Homogeneous Mixtures

    Directory of Open Access Journals (Sweden)

    Dipal Patel

    2015-06-01

    Full Text Available The effects of the characteristic width of the energy deposition profile and the duration of energy deposition by the ignitor on localised forced ignition of stoichiometric and fuel-lean homogeneous mixtures have been analysed using simplified chemistry three-dimensional compressible Direct Numerical Simulation (DNS for different values of root-mean-square turbulent velocity fluctuation. The localised forced ignition is modelled using a source term in the energy transport equation, which deposits energy in a Gaussian manner from the centre of the ignitor over a stipulated period of time. It has been shown that the width of ignition energy deposition and the duration over which ignition energy is deposited have significant influences on the success of ignition and subsequent flame propagation. An increase in the width of ignition energy deposition (duration of energy deposition for a given amount of ignition energy has been found to have a detrimental effect on the ignition event, which may ultimately lead to misfire. Moreover, an increase in u′ gives rise to augmented heat transfer rate from the hot gas kernel, which in turn leads to a reduction in the extent of overall burning for both stoichiometric and fuel-lean homogeneous mixtures but the detrimental effects of high values of u′ on localised ignition are particularly prevalent for fuel-lean mixtures.

  2. Processing Research on Chemically Vapor Deposited Silicon Nitride.

    Science.gov (United States)

    1979-12-01

    34 sea urchins ") predominated, suggesting that formation was primarily from the vapor phase with little of the nodular growths seen at only slightly...deposition parameters on crystallite size, morphology and deposition rate. Geometries include a cold-wall, flat plate reactor (CW) and 4-inch and 1-inch...typical crossections of banded deposits and deposits which showed transitions from amorphous to crystalline morphologies , respectively. Figure 2-5

  3. Particle dry deposition to water surfaces: Processes and consequences

    DEFF Research Database (Denmark)

    Pryor, S.C.; Barthelmie, R.J.

    2000-01-01

    Algal blooms (increased abundance of phytoplankton) are an increasingly common phenomenon which has been causally linked to increased fluxes of nutrient (particularly nitrogenous) compounds to aquatic ecosystems. These blooms have implications for water quality and human health in addition...... flux to coastal waters, atmosphere-surface exchange represents a significant component of the total flux and may be particularly critical during the summertime when both the riverine input and ambient nutrient concentrations are often at a minimum. In this chapter, we present an overview...... of the physical and chemical processes which dictate the quantity (and direction) of atmosphere-surface fluxes of trace chemicals to (and above) water surfaces with particular emphasis on the role of particles. Dry deposition (transfer to the surface in the absence of precipitation) of particles is determined...

  4. Deposition Mechanisms and Oxidation Behaviors of Ti-Ni Coatings Deposited in Low-Temperature HVOF Spraying Process

    Science.gov (United States)

    Lin, Q. S.; Zhou, K. S.; Deng, C. M.; Liu, M.; Xu, L. P.; Deng, C. G.

    2014-08-01

    Three kinds of Ti-Ni powders were deposited on 316L stainless steel by low-temperature high-velocity oxygen fuel (LT-HVOF) spraying process, respectively. Deposition mechanisms and oxidation behaviors of the coatings were researched in this paper. The coating deposited from TiNi intermetallic powder had obvious laminar structure and the oxygen content was the highest among the three kinds of coatings. The oxygen content of the coating deposited from small-sized Ni-clad Ti powder was still high due to the melting of parts of particles. However, most of the coarse Ni-clad Ti powder was deposited in solid states without changes of chemical compositions and phase compositions. The oxygen content of the coating deposited from coarse Ni-clad Ti powder was the lowest among the three kinds of coatings. It indicated that the deposition behavior of the coating could effectively preserve the inner titanium from oxidation. The results of the present research demonstrated that it is entirely feasible to deposit active metal materials such as titanium and titanium alloy through the optimizing selection of powder in the LT-HVOF process.

  5. Enhancement of surface integrity of titanium alloy with copper by means of laser metal deposition process

    CSIR Research Space (South Africa)

    Erinosho, MF

    2016-04-01

    Full Text Available The laser metal deposition process possesses the combination of metallic powder and laser beam respectively. However, these combinations create an adhesive bonding that permanently solidifies the laser-enhanced-deposited powders. Titanium alloys (Ti...

  6. Macro controlling of copper oxide deposition processes and spray mode by using home-made fully computerized spray pyrolysis system

    Science.gov (United States)

    Essa, Mohammed Sh.; Chiad, Bahaa T.; Shafeeq, Omer Sh.

    2017-09-01

    Thin Films of Copper Oxide (CuO) absorption layer have been deposited using home-made Fully Computerized Spray Pyrolysis Deposition system FCSPD on glass substrates, at the nozzle to substrate distance equal to 20,35 cm, and computerized spray mode (continues spray, macro-control spray). The substrate temperature has been kept at 450 °c with the optional user can enter temperature tolerance values ± 5 °C. Also that fixed molar concentration of 0.1 M, and 2D platform speed or deposition platform speed of 4mm/s. more than 1000 instruction program code, and specific design of graphical user interface GUI to fully control the deposition process and real-time monitoring and controlling the deposition temperature at every 200 ms. The changing in the temperature has been recorded during deposition processes, in addition to all deposition parameters. The films have been characterized to evaluate the thermal distribution over the X, Y movable hot plate, the structure and optical energy gap, thermal and temperature distribution exhibited a good and uniform distribution over 20 cm2 hot plate area, X-ray diffraction (XRD) measurement revealed that the films are polycrystalline in nature and can be assigned to monoclinic CuO structure. Optical band gap varies from 1.5-1.66 eV depending on deposition parameter.

  7. Electrode surface engineering by atomic layer deposition: A promising pathway toward better energy storage

    KAUST Repository

    Ahmed, Bilal

    2016-04-29

    Research on electrochemical energy storage devices including Li ion batteries (LIBs), Na ion batteries (NIBs) and supercapacitors (SCs) has accelerated in recent years, in part because developments in nanomaterials are making it possible to achieve high capacities and energy and power densities. These developments can extend battery life in portable devices, and open new markets such as electric vehicles and large-scale grid energy storage. It is well known that surface reactions largely determine the performance and stability of electrochemical energy storage devices. Despite showing impressive capacities and high energy and power densities, many of the new nanostructured electrode materials suffer from limited lifetime due to severe electrode interaction with electrolytes or due to large volume changes. Hence control of the surface of the electrode material is essential for both increasing capacity and improving cyclic stability of the energy storage devices.Atomic layer deposition (ALD) which has become a pervasive synthesis method in the microelectronics industry, has recently emerged as a promising process for electrochemical energy storage. ALD boasts excellent conformality, atomic scale thickness control, and uniformity over large areas. Since ALD is based on self-limiting surface reactions, complex shapes and nanostructures can be coated with excellent uniformity, and most processes can be done below 200. °C. In this article, we review recent studies on the use of ALD coatings to improve the performance of electrochemical energy storage devices, with particular emphasis on the studies that have provided mechanistic insight into the role of ALD in improving device performance. © 2016 Elsevier Ltd.

  8. Dual-energy CT (DECT) imaging of tophi and monosodium urate deposits in a patient with longstanding anorexia nervosa

    DEFF Research Database (Denmark)

    Weihe, Johan Petur; Birger Morillon, Melanie; Lambrechtsen, Jess

    Dual-energy CT (DECT) imaging of tophi and monosodium urate deposits in a patient with longstanding anorexia nervosa......Dual-energy CT (DECT) imaging of tophi and monosodium urate deposits in a patient with longstanding anorexia nervosa...

  9. Biomass conversion processes for energy and fuels

    Science.gov (United States)

    Sofer, S. S.; Zaborsky, O. R.

    The book treats biomass sources, promising processes for the conversion of biomass into energy and fuels, and the technical and economic considerations in biomass conversion. Sources of biomass examined include crop residues and municipal, animal and industrial wastes, agricultural and forestry residues, aquatic biomass, marine biomass and silvicultural energy farms. Processes for biomass energy and fuel conversion by direct combustion (the Andco-Torrax system), thermochemical conversion (flash pyrolysis, carboxylolysis, pyrolysis, Purox process, gasification and syngas recycling) and biochemical conversion (anaerobic digestion, methanogenesis and ethanol fermentation) are discussed, and mass and energy balances are presented for each system.

  10. Diplog analysis of paleocurrent and depositional energy of Miocene ...

    African Journals Online (AJOL)

    The interaction of these nearshore influences and the resulting pattern of sedimentation of the reservoir sands reinforce the conclusions drawn from studies conducted on Quaternary sediments along the Nigerian southwest coast and on Cretaceous sediments in the adjoining Anambra Basin. The levels of depositional ...

  11. Energy scenarios for Colombia: process and content

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Ricardo A. [National Univ. of Colombia, Escuela de Geosciencias y Medio Ambiente, Medellin (Colombia); Vesga, Daniel R.A. [Unidad de Planeacion Minero Energetica, Bogota (Colombia); Cadena, Angela I. [Los Andes Univ., School of Engineering, Bogota (Colombia); Boman, Ulf [Kairos Future AB, Stockholm (Sweden); Larsen, Erik [Cass Business School, London (United Kingdom); Dyner, Isaac [Universidad Nacional de Colombia, Energy Inst., Medellin (Colombia)

    2005-02-01

    This paper presents the approach undertaken, and the four energy scenarios that have been developed, to support long term energy policy in Colombia. The scenarios were constructed with emphasis on maximum interaction between stakeholders in the Colombian energy sector. The process directly involved over 120 people. The scenarios were developed as strategic support tools for the Energy and Mining Planning Unit (UPME), which is the Colombian institution in charge of developing the country's energy strategies and National Energy Policy. The methodology employed is presented, followed by a detailed description of each of the four scenarios. (Author)

  12. Understanding processes affecting mineral deposits in humid environments

    Science.gov (United States)

    Seal, Robert R.; Ayuso, Robert A.

    2011-01-01

    Recent interdisciplinary studies by the U.S. Geological Survey have resulted in substantial progress toward understanding the influence that climate and hydrology have on the geochemical signatures of mineral deposits and the resulting mine wastes in the eastern United States. Specific areas of focus include the release, transport, and fate of acid, metals, and associated elements from inactive mines in temperate coastal areas and of metals from unmined mineral deposits in tropical to subtropical areas; the influence of climate, geology, and hydrology on remediation options for abandoned mines; and the application of radiogenic isotopes to uniquely apportion source contributions that distinguish natural from mining sources and extent of metal transport. The environmental effects of abandoned mines and unmined mineral deposits result from a complex interaction of a variety of chemical and physical factors. These include the geology of the mineral deposit, the hydrologic setting of the mineral deposit and associated mine wastes, the chemistry of waters interacting with the deposit and associated waste material, the engineering of a mine as it relates to the reactivity of mine wastes, and climate, which affects such factors as temperature and the amounts of precipitation and evapotranspiration; these factors, in turn, influence the environmental behavior of mineral deposits. The role of climate is becoming increasingly important in environmental investigations of mineral deposits because of the growing concerns about climate change.

  13. Local Measurement of Fuel Energy Deposition and Heat Transfer Environment During Fuel Lifetime Using Controlled Calorimetry

    Energy Technology Data Exchange (ETDEWEB)

    Don W. Miller; Andrew Kauffmann; Eric Kreidler; Dongxu Li; Hanying Liu; Daniel Mills; Thomas D. Radcliff; Joseph Talnagi

    2001-12-31

    A comprehensive description of the accomplishments of the DOE grant titled, ''Local Measurement of Fuel Energy Deposition and Heat Transfer Environment During Fuel Lifetime using Controlled Calorimetry''.

  14. Nanostructure of PDMS–TEOS–PrZr hybrids prepared by direct deposition of gamma radiation energy

    Energy Technology Data Exchange (ETDEWEB)

    Lancastre, Joana J.H., E-mail: jlancastre@ctn.ist.utl.pt [C2TN, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 (km 139.7), 2695-066 Bobadela, LRS (Portugal); Falcão, António N. [C2TN, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 (km 139.7), 2695-066 Bobadela, LRS (Portugal); Margaça, Fernanda M.A., E-mail: fmargaca@ctn.ist.utl.pt [C2TN, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 (km 139.7), 2695-066 Bobadela, LRS (Portugal); Ferreira, Luís M. [C2TN, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10 (km 139.7), 2695-066 Bobadela, LRS (Portugal); Miranda Salvado, Isabel M. [CICECO & Departamento de Engenharia de Materiais e Cerâmica, Universidade de Aveiro, Campus de Santiago, 3810-193 Aveiro (Portugal); Almásy, László [Wigner Research Centre for Physics, Institute for Solid State Physics and Optics, PO Box 49, 1525 Budapest (Hungary); Casimiro, Maria H. [REQUIMTE/CQFB, Departamento de Química, Faculdade de Ciências e Tecnologia, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Meiszterics, Anikó [Gedeon Richter Ltd., PO Box 27, H-1475 Budapest (Hungary)

    2015-10-15

    Highlights: • Hybrid materials were prepared by direct energy deposition. • The influence of the catalyst content (PrZr) was investigated. • The developed oxide network was found to be strongly dependent on the PrZr content. • A model is proposed for the development of the oxide network in these materials. - Abstract: Organic–inorganic materials have been the object of intense research due to their wide range of properties and therefore innumerous applications. We prepared organic–inorganic hybrid materials by direct energy deposition on a mixture of polydimethylsiloxane silanol terminated (33 wt% fixed content), tetraethylorthosilicate and a minor content of zirconium propoxide that varied from 1 to 5 wt% using gamma radiation from a Co-60 source. The samples, dried in air at room temperature, are bulk, flexible and transparent. Their nanostructure was investigated by small angle neutron scattering. It was found that the inorganic oxide network has fractal structure, which becomes denser as the zirconium propoxide content decreases. The results suggest that oxide nanosized regions grow from the OH terminal group of PDMS which are the condensation seeds. Their number and position remains unaltered with the variation of zirconium propoxide content that only affects their microstructure. A model is proposed for the nanostructure of the oxide network that develops in the irradiation processed hybrid materials.

  15. Solar energy engineering processes and systems

    CERN Document Server

    Kalogirou, Soteris A

    2009-01-01

    As perhaps the most promising of all the renewable energy sources available today, solar energy is becoming increasingly important in the drive to achieve energy independence and climate balance. This new book is the masterwork from world-renowned expert Dr. Soteris Kalogirou, who has championed solar energy for decades. The book includes all areas of solar energy engineering, from the fundamentals to the highest level of current research. The author includes pivotal subjects such as solar collectors, solar water heating, solar space heating and cooling, industrial process heat, solar desalina

  16. Solar energy engineering processes and systems

    CERN Document Server

    Kalogirou, Soteris A

    2013-01-01

    As perhaps the most promising of all the renewable energy sources available today, solar energy is becoming increasingly important in the drive to achieve energy independence and climate balance. This new book is the masterwork from world-renowned expert Dr. Soteris Kalogirou, who has championed solar energy for decades. The book includes all areas of solar energy engineering, from the fundamentals to the highest level of current research. The author includes pivotal subjects such as solar collectors, solar water heating, solar space heating and cooling, industrial process heat, solar desalina

  17. Integration of Electrodeposited Ni-Fe in MEMS with Low-Temperature Deposition and Etch Processes

    National Research Council Canada - National Science Library

    Giuseppe Schiavone; Jeremy Murray; Richard Perry; Andrew R Mount; Marc P Y Desmulliez; Anthony J Walton

    2017-01-01

    .... In addition, a low temperature deposition and surface micromachining process is presented in which silicon dioxide and silicon nitride are used, respectively, as sacrificial material and structural dielectric...

  18. Analysis of Fiber deposition using Automatic Image Processing Method

    Science.gov (United States)

    Belka, M.; Lizal, F.; Jedelsky, J.; Jicha, M.

    2013-04-01

    Fibers are permanent threat for a human health. They have an ability to penetrate deeper in the human lung, deposit there and cause health hazards, e.glung cancer. An experiment was carried out to gain more data about deposition of fibers. Monodisperse glass fibers were delivered into a realistic model of human airways with an inspiratory flow rate of 30 l/min. Replica included human airways from oral cavity up to seventh generation of branching. Deposited fibers were rinsed from the model and placed on nitrocellulose filters after the delivery. A new novel method was established for deposition data acquisition. The method is based on a principle of image analysis. The images were captured by high definition camera attached to a phase contrast microscope. Results of new method were compared with standard PCM method, which follows methodology NIOSH 7400, and a good match was found. The new method was found applicable for evaluation of fibers and deposition fraction and deposition efficiency were calculated afterwards.

  19. Hypersonic wave drag reduction performance of cylinders with repetitive laser energy depositions

    Energy Technology Data Exchange (ETDEWEB)

    Fang, J; Hong, Y J; Li, Q; Huang, H, E-mail: fangjuan314@163.com [Academy of Equipment Command and Technology, Post Box 3380-86, Huairou Dis. Beijing 101416 (China)

    2011-02-01

    It has been widely research that wave drag reduction on hypersonic vehicle by laser energy depositions. Using laser energy to reduce wave drag can improve vehicle performance. A second order accurate scheme based on finite-difference method and domain decomposition of structural grid is used to compute the drag performance of cylinders in a hypersonic flow of Mach number 2 at altitude of 15km with repetitive energy depositions. The effects of frequency on drag reduction are studied. The calculated results show: the recirculation zone is generated due to the interaction between bow shock over the cylinder and blast wave produced by energy deposition, and a virtual spike which is supported by an axis-symmetric recirculation, is formed in front of the cylinder. By increasing the repetitive frequency, the drag is reduced and the oscillation of the drag is decreased; however, the energy efficiency decreases by increasing the frequency.

  20. Laser-induced multi-energy processing in diamond growth

    Science.gov (United States)

    Xie, Zhiqiang

    Laser-induced multi-energy processing (MEP) introduces resonant vibrational excitations of precursor molecules to conventional chemical vapor deposition methods for material synthesis. In this study, efforts were extended to explore the capability of resonant vibrational excitations for promotion of energy efficiency in chemical reactions, for enhancement of diamond deposition, and for control of chemical reactions. The research project mainly focused on resonant vibrational excitations of precursor molecules using lasers in combustion flame deposition of diamond, which led to: 1) promotion of chemical reactions; 2) enhancement of diamond growth with higher growth rate and better crystallizations; 3) steering of chemical reactions which lead to preferential growth of {100}-oriented diamond films and crystals; and 4) mode-selective excitations of precursor molecules toward bond-selective control of chemical reactions. Diamond films and crystals were deposited in open air by combustion flame deposition through resonant vibrational excitations of precursor molecules, including ethylene (C2H4) and propylene (C3H 6). A kilowatt wavelength-tunable CO2 laser with spectral range from 9.2 to 10.9 microm was tuned to match vibrational modes of the precursor molecules. Resonant vibrational excitations of these molecules were achieved with high energy efficiency as compared with excitations using a common CO2 laser (fixed wavelength at 10.591microm). With resonant vibrational excitations, the diamond growth rate was increased; diamond quality was promoted; diamond crystals with lengths up to 5 mm were deposited in open air; preferential growth of {100}-oriented diamond films and single crystals was achieved; mode-selective excitations of precursor molecules were investigated toward control of chemical reactions. Optical emission spectroscopy (OES), mass spectrometry (MS), and molecular dynamic simulations were conducted to obtain an in-depth understanding of the resonant

  1. Nitrogen deposition to the United States: distribution, sources, and processes

    Directory of Open Access Journals (Sweden)

    L. Zhang

    2012-05-01

    Full Text Available We simulate nitrogen deposition over the US in 2006–2008 by using the GEOS-Chem global chemical transport model at 1/2°×2/3° horizontal resolution over North America and adjacent oceans. US emissions of NOx and NH3 in the model are 6.7 and 2.9 Tg N a−1 respectively, including a 20% natural contribution for each. Ammonia emissions are a factor of 3 lower in winter than summer, providing a good match to US network observations of NHx (≡NH3 gas + ammonium aerosol and ammonium wet deposition fluxes. Model comparisons to observed deposition fluxes and surface air concentrations of oxidized nitrogen species (NOy show overall good agreement but excessive wintertime HNO3 production over the US Midwest and Northeast. This suggests a model overestimate N2O5 hydrolysis in aerosols, and a possible factor is inhibition by aerosol nitrate. Model results indicate a total nitrogen deposition flux of 6.5 Tg N a−1 over the contiguous US, including 4.2 as NOy and 2.3 as NHx. Domestic anthropogenic, foreign anthropogenic, and natural sources contribute respectively 78%, 6%, and 16% of total nitrogen deposition over the contiguous US in the model. The domestic anthropogenic contribution generally exceeds 70% in the east and in populated areas of the west, and is typically 50–70% in remote areas of the west. Total nitrogen deposition in the model exceeds 10 kg N ha−1 a−1 over 35% of the contiguous US.

  2. The adsorptive-kinetic model of in-situ phosphorus doped film polysilicon deposition process

    Directory of Open Access Journals (Sweden)

    Nalivaiko O. Yu.

    2009-11-01

    Full Text Available The investigation of deposition kinetics of in-situ phosphorus doped polysilicon films has been performed. The adsorptive-kinetic model of in-situ phosphorus doped polysilicon deposition has been developed. The values of heterogeneous reaction constants and constants, which describe the desorption process for monosilane and phosphine, have been defined. The optimal process conditions, which provide the acceptable deposition rate, thickness uniformity, high doping level and conformal step coverage, have been founded.

  3. Investigation on the correlation between energy deposition and clustered DNA damage induced by low-energy electrons.

    Science.gov (United States)

    Liu, Wei; Tan, Zhenyu; Zhang, Liming; Champion, Christophe

    2018-01-15

    This study presents the correlation between energy deposition and clustered DNA damage, based on a Monte Carlo simulation of the spectrum of direct DNA damage induced by low-energy electrons including the dissociative electron attachment. Clustered DNA damage is classified as simple and complex in terms of the combination of single-strand breaks (SSBs) or double-strand breaks (DSBs) and adjacent base damage (BD). The results show that the energy depositions associated with about 90% of total clustered DNA damage are below 150 eV. The simple clustered DNA damage, which is constituted of the combination of SSBs and adjacent BD, is dominant, accounting for 90% of all clustered DNA damage, and the spectra of the energy depositions correlating with them are similar for different primary energies. One type of simple clustered DNA damage is the combination of a SSB and 1-5 BD, which is denoted as SSB + BD. The average contribution of SSB + BD to total simple clustered DNA damage reaches up to about 84% for the considered primary energies. In all forms of SSB + BD, the SSB + BD including only one base damage is dominant (above 80%). In addition, for the considered primary energies, there is no obvious difference between the average energy depositions for a fixed complexity of SSB + BD determined by the number of base damage, but average energy depositions increase with the complexity of SSB + BD. In the complex clustered DNA damage constituted by the combination of DSBs and BD around them, a relatively simple type is a DSB combining adjacent BD, marked as DSB + BD, and it is of substantial contribution (on average up to about 82%). The spectrum of DSB + BD is given mainly by the DSB in combination with different numbers of base damage, from 1 to 5. For the considered primary energies, the DSB combined with only one base damage contributes about 83% of total DSB + BD, and the average energy deposition is about 106 eV. However, the

  4. Experiment of Flow Control Using Laser Energy Deposition Around High Speed Propulsion System

    Science.gov (United States)

    Lee, HyoungJin; Jeung, InSeuck; Lee, SangHun; Kim, Seihwan

    2011-11-01

    An experimental investigation was conducted to examine the effect of a pulsed Nd:YAG laser energy deposition on the shock structures in supersonic/hypersonic flow and quiescent air. The effect of the laser energy and pressure in the blast wave generation were also investigated. As a result, the strength of plasma and blast wave becomes stronger as pressure or laser energy increase. And the breakdown threshold of air by laser energy deposition is 0.015 bar at 508 mJ laser energy, the blast wave threshold generation in air by laser energy deposition is 0.100 bar at same laser energy. As qualitative analysis, schlieren images are also obtained. After the series of experiments, the effect of laser energy deposition (LED) on high speed flow around the shock—shock interaction created by a wedge and blunt body. By LED, the structure of shock—shock interaction was collapsed momentary and the pressure of the stagnation point was fluctuated while interference of wave.

  5. Electrochemically Deposited Nickel Membranes; Process-Microstructure-Property Relationships

    DEFF Research Database (Denmark)

    Jensen, Jens Dahl; Pantleon, Karen; Somers, Marcel A.J.

    2003-01-01

    -type foils during thin film tensile testing, due to microstructural defects caused by sodium saccharin during deposition. Tensile strengths in the order of 700-1000 MPa were observed - highest for the more ductile 0-type foils. A hardness in the order of 6 GPa (590 HV) was found by nanoindentation. Keywords...

  6. Energy balance in solid state fermentation processes

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, L.J.A.; Torres, A.; Echevarria, J.; Saura, G. (Instituto Cubano de Investigaciones de los Derivados de la Cana de Azucar (ICIDCA), La Habana (Cuba))

    1991-01-01

    It was applied a macroscopic energy balance to a solid state fermentation process and an electron balance in order to estimate the temperature and the heat evolved in the process. There were employed several equations that describe the development of the system and offer the possibility to design or control such fermentations. (orig.).

  7. The fate of SOC during the processes of water erosion and subsequent deposition: a field study.

    Science.gov (United States)

    van Hemelryck, H.; Govers, G.; van Oost, K.; Merckx, R.

    2009-04-01

    Globally soils are the largest terrestrial pool of carbon (C). A relatively small increase or decrease in soil carbon content due to changes in land use or management practices could therefore result in a significant net exchange of C between the soil C reservoir and the atmosphere. As such, the geomorphic processes of water and tillage erosion have been identified to significantly impact on this large pool of soil organic carbon (SOC). Soil erosion, transport and deposition not only result in redistribution of sediments and associated carbon within a landscape, but also affect the exchange of C between the pedosphere and the atmosphere. The direction and magnitude of an erosion-induced change in the global C balance is however a topic of much debate as opposing processes interact: i) At eroding sites a net uptake of C could be the result of reduced respiration rates and continued inputs of newly produced carbon. ii) Colluvial deposition of eroded sediment and SOC leads to the burial of the original topsoil and this may constrain the decomposition of its containing SOC. iii) Eroded sediment could be transported to distal depositional environments or fluvial systems where it will either be conserved or become rapidly mineralized. iv) Increased emission of CO2 due to erosion may result from the disruptive energy of erosive forces causing the breakdown of aggregates and exposing previously protected SOC to microbial decomposition. The above-mentioned processes show a large spatial and temporal variability and assessing their impact requires an integrated modeling approach. However uncertainties about the basic processes that accompany SOC displacement are still large. This study focuses on one of these large information gaps: the fate of eroded and subsequently deposited SOC. A preceding experimental study (Van Hemelryck et al., 2008) was used to identify controlling factors (erosional intensity, changes in soil structure,…). However this experimental research

  8. Deposition of luminescent thin films for solar energy applications

    NARCIS (Netherlands)

    De Jong, M.

    2015-01-01

    Photovoltaic devices are a widely available, long lasting means of generating sustainable energy. Unfortunately, the integration of such devices into society is to date still limited. This is in part due to the much less than optimal efficiency of conversion of sunlight to electricity, but also by

  9. Geothermal energy market potential in industrial processing

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, R.J.; Hanny, J.A.; Knuth, W.H.

    1978-11-01

    Geothermal energy is currently being used for a number of industrial processes in countries throughout the world. Its application in the United States is mainly limited to space heating even though the temperature of the geothermal fluid is sufficient for process uses, and could be sold at attractive prices while maintaining a high return on investment. The temperature span for industrial use ranges from 40 to 275/sup 0/C, thus encompassing both the abundant low temperature and the less available high temperature resources. Hydrothermal fluids can be used either directly or indirectly dependent upon fluid quality and process needs. The barriers facing hydrothermal industrial process development are (a) the development infrastructure does not exist, (b) energy users are not aware of hydrothermal energy and its advantages, (c) federal incentives are limited, (d) resources are not fully defined.

  10. Detailed Kinetic Modeling of Processes Relevant To Fusion Energy

    Science.gov (United States)

    Mehl, Marco; Armstrong, Michael; Zaug, Joseph; Crowhurst, Jonathan; Radousky, Harry; Stavrou, Elissaios

    2016-10-01

    Carbon based materials have been proposed as candidates for the fabrication of plasma-facing components in the design of fusion energy devices. Although these components are not supposed to be in direct contact with the core fusion plasma, plasma instabilities and the harsh environment they are exposed to can cause the degradation of plasma-exposed components and the transfer of contaminants into the plasma followed by deposition of byproducts. In order to investigate the chemistry involved in these processes and to assist the development of models suitable to understand the long term consequences of the carbon ablation/deposition cycle, an inductively coupled plasma flow reactor (ICPFR) has been developed. The ICPFR allows the atomization of carbon containing precursors to high temperatures (in the order of 10000K) and the characterization of the gas and solid species formed downsteam from the plasma source through spectroscopic techniques. In parallel to the experimental analysis a comprehensive set of fluid dynamic and detailed kinetic simulations are used to analyze the data. The combination of these two approaches resulted in a validated and comprehensive chemical model for the formation of carbon deposits in carbon contaminated cooling plasmas. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

  11. Study of Key Non-dimensional Parameters for Wave Drag Reduction with High-Frequency Repetitive Laser Pulse Energy Depositions

    Directory of Open Access Journals (Sweden)

    Qing Zexu

    2016-01-01

    Full Text Available The problem of wave drag reduction with high-frequency repetitive laser pulse energy depositions is multivariable. Three key non-dimensional parameters, non-dimensional energy, non-dimensional depositing position and Mach number, were constructed from a number of original variables by using Buckingham pi theorem. Influences of these non-dimensional parameters on energy deposition performance, namely drag reduction and energy deposition efficiency, were investigated numerically by solving three-dimensional Navier-Stokes equations with an upwind scheme. Optimizing method of non-dimensional energy and non-dimensional depositing position is proposed. Drag reduction and energy deposition efficiency have exponential relationships with non-dimensional energy; Drag reduction and energy deposition efficiency have quadratic relationships with non-dimensional depositing position. Drag reduction has exponential relationship with freestream Mach number and energy deposition efficiency has quadratic relationship with Mach number. Non-dimensional laser energy and non-dimensional depositing position should be optimized synthetically for a given freestream.

  12. Research on chemical vapor deposition processes for advanced ceramic coatings

    Science.gov (United States)

    Rosner, Daniel E.

    1993-01-01

    Our interdisciplinary background and fundamentally-oriented studies of the laws governing multi-component chemical vapor deposition (VD), particle deposition (PD), and their interactions, put the Yale University HTCRE Laboratory in a unique position to significantly advance the 'state-of-the-art' of chemical vapor deposition (CVD) R&D. With NASA-Lewis RC financial support, we initiated a program in March of 1988 that has led to the advances described in this report (Section 2) in predicting chemical vapor transport in high temperature systems relevant to the fabrication of refractory ceramic coatings for turbine engine components. This Final Report covers our principal results and activities for the total NASA grant of $190,000. over the 4.67 year period: 1 March 1988-1 November 1992. Since our methods and the technical details are contained in the publications listed (9 Abstracts are given as Appendices) our emphasis here is on broad conclusions/implications and administrative data, including personnel, talks, interactions with industry, and some known applications of our work.

  13. In Situ Studies of Energy Deposition by Ion Beams.

    Science.gov (United States)

    1985-06-14

    M. Choi , J. Groeger, F. A. Otter, Y. Bruynseraede and M. Clapp. 1984. Modifications in the unit cell geometry of sputtered niobium films caused by...Budnick, M. Choi , J. Groeger, F. A. Otter, Y. Bruynseraede and M. Clapp. 1984. Modifications in the unit cell geometry of sputtered niobium films caused by...helw.V beam off 3. Experimental Results b Z 18 L iNhO 0 4C Exposure of the LiNbO 3 to an Ar+ ion beam of pairticle energy 100 key and current density

  14. Membranes for environmentally friendly energy processes.

    Science.gov (United States)

    He, Xuezhong; Hägg, May-Britt

    2012-10-18

    Membrane separation systems require no or very little chemicals compared to standard unit operations. They are also easy to scale up, energy efficient, and already widely used in various gas and liquid separation processes. Different types of membranes such as common polymers, microporous organic polymers, fixed-site-carrier membranes, mixed matrix membranes, carbon membranes as well as inorganic membranes have been investigated for CO2 capture/removal and other energy processes in the last two decades. The aim of this work is to review the membrane systems applied in different energy processes, such as post-combustion, pre-combustion, oxyfuel combustion, natural gas sweetening, biogas upgrading, hydrogen production, volatile organic compounds (VOC) recovery and pressure retarded osmosis for power generation. Although different membranes could probably be used in a specific separation process, choosing a suitable membrane material will mainly depend on the membrane permeance and selectivity, process conditions (e.g., operating pressure, temperature) and the impurities in a gas stream (such as SO2, NOx, H2S, etc.). Moreover, process design and the challenges relevant to a membrane system are also being discussed to illustrate the membrane process feasibility for a specific application based on process simulation and economic cost estimation.

  15. Membranes for Environmentally Friendly Energy Processes

    Directory of Open Access Journals (Sweden)

    Xuezhong He

    2012-10-01

    Full Text Available Membrane separation systems require no or very little chemicals compared to standard unit operations. They are also easy to scale up, energy efficient, and already widely used in various gas and liquid separation processes. Different types of membranes such as common polymers, microporous organic polymers, fixed-site-carrier membranes, mixed matrix membranes, carbon membranes as well as inorganic membranes have been investigated for CO2 capture/removal and other energy processes in the last two decades. The aim of this work is to review the membrane systems applied in different energy processes, such as post-combustion, pre-combustion, oxyfuel combustion, natural gas sweetening, biogas upgrading, hydrogen production, volatile organic compounds (VOC recovery and pressure retarded osmosis for power generation. Although different membranes could probably be used in a specific separation process, choosing a suitable membrane material will mainly depend on the membrane permeance and selectivity, process conditions (e.g., operating pressure, temperature and the impurities in a gas stream (such as SO2, NOx, H2S, etc.. Moreover, process design and the challenges relevant to a membrane system are also being discussed to illustrate the membrane process feasibility for a specific application based on process simulation and economic cost estimation.

  16. Membranes for Environmentally Friendly Energy Processes

    Science.gov (United States)

    He, Xuezhong; Hägg, May-Britt

    2012-01-01

    Membrane separation systems require no or very little chemicals compared to standard unit operations. They are also easy to scale up, energy efficient, and already widely used in various gas and liquid separation processes. Different types of membranes such as common polymers, microporous organic polymers, fixed-site-carrier membranes, mixed matrix membranes, carbon membranes as well as inorganic membranes have been investigated for CO2 capture/removal and other energy processes in the last two decades. The aim of this work is to review the membrane systems applied in different energy processes, such as post-combustion, pre-combustion, oxyfuel combustion, natural gas sweetening, biogas upgrading, hydrogen production, volatile organic compounds (VOC) recovery and pressure retarded osmosis for power generation. Although different membranes could probably be used in a specific separation process, choosing a suitable membrane material will mainly depend on the membrane permeance and selectivity, process conditions (e.g., operating pressure, temperature) and the impurities in a gas stream (such as SO2, NOx, H2S, etc.). Moreover, process design and the challenges relevant to a membrane system are also being discussed to illustrate the membrane process feasibility for a specific application based on process simulation and economic cost estimation. PMID:24958426

  17. Energy conversion processes in the outer planets

    Science.gov (United States)

    Gierasch, P. J.; Conrath, B. J.

    1985-01-01

    Energy conversion processes which are potentially important in the outer planets at pressures greater than obut 0.1 bar are reviewed. Generation of buoyancy contrasts by condensation of various constituents is discussed with emphasis on the possible significance of phase changes in substances such as Si and Mg compounds at deep levels. It is demonstrated that, in the absence of nonequilibrium thermodynamic processes, strong kinetic energy generation must accompany the transport of heat out of the high temperature planetary interiors. The possibly dominant role of lagged parahydrogen conversion in the convective transport of heat at levels where T is less than 300 K is discussed. Measurements which may ultimately contribute to a better understanding of energy conversion processes are summarized.

  18. Energy deposition by heavy ions: Additivity of kinetic and potential energy contributions in hillock formation on CaF2

    Science.gov (United States)

    Wang, Y. Y.; Grygiel, C.; Dufour, C.; Sun, J. R.; Wang, Z. G.; Zhao, Y. T.; Xiao, G. Q.; Cheng, R.; Zhou, X. M.; Ren, J. R.; Liu, S. D.; Lei, Y.; Sun, Y. B.; Ritter, R.; Gruber, E.; Cassimi, A.; Monnet, I.; Bouffard, S.; Aumayr, F.; Toulemonde, M.

    2014-01-01

    Modification of surface and bulk properties of solids by irradiation with ion beams is a widely used technique with many applications in material science. In this study, we show that nano-hillocks on CaF2 crystal surfaces can be formed by individual impact of medium energy (3 and 5 MeV) highly charged ions (Xe22+ to Xe30+) as well as swift (kinetic energies between 12 and 58 MeV) heavy xenon ions. For very slow highly charged ions the appearance of hillocks is known to be linked to a threshold in potential energy (Ep) while for swift heavy ions a minimum electronic energy loss per unit length (Se) is necessary. With our results we bridge the gap between these two extreme cases and demonstrate, that with increasing energy deposition via Se the Ep-threshold for hillock production can be lowered substantially. Surprisingly, both mechanisms of energy deposition in the target surface seem to contribute in an additive way, which can be visualized in a phase diagram. We show that the inelastic thermal spike model, originally developed to describe such material modifications for swift heavy ions, can be extended to the case where both kinetic and potential energies are deposited into the surface. PMID:25034006

  19. Energy deposition by heavy ions: additivity of kinetic and potential energy contributions in hillock formation on CaF2.

    Science.gov (United States)

    Wang, Y Y; Grygiel, C; Dufour, C; Sun, J R; Wang, Z G; Zhao, Y T; Xiao, G Q; Cheng, R; Zhou, X M; Ren, J R; Liu, S D; Lei, Y; Sun, Y B; Ritter, R; Gruber, E; Cassimi, A; Monnet, I; Bouffard, S; Aumayr, F; Toulemonde, M

    2014-07-18

    Modification of surface and bulk properties of solids by irradiation with ion beams is a widely used technique with many applications in material science. In this study, we show that nano-hillocks on CaF2 crystal surfaces can be formed by individual impact of medium energy (3 and 5 MeV) highly charged ions (Xe(22+) to Xe(30+)) as well as swift (kinetic energies between 12 and 58 MeV) heavy xenon ions. For very slow highly charged ions the appearance of hillocks is known to be linked to a threshold in potential energy (Ep) while for swift heavy ions a minimum electronic energy loss per unit length (Se) is necessary. With our results we bridge the gap between these two extreme cases and demonstrate, that with increasing energy deposition via Se the Ep-threshold for hillock production can be lowered substantially. Surprisingly, both mechanisms of energy deposition in the target surface seem to contribute in an additive way, which can be visualized in a phase diagram. We show that the inelastic thermal spike model, originally developed to describe such material modifications for swift heavy ions, can be extended to the case where both kinetic and potential energies are deposited into the surface.

  20. Particle production and energy deposition studies for the neutrino factory target station

    Directory of Open Access Journals (Sweden)

    John J. Back

    2013-02-01

    Full Text Available We present FLUKA and MARS simulation studies of the pion production and energy deposition in the Neutrino Factory baseline target station, which consists of a 4 MW proton beam interacting with a liquid mercury jet target within a 20 T solenoidal magnetic field. We show that a substantial increase in the shielding is needed to protect the superconducting coils from too much energy deposition. Investigations reveal that it is possible to reduce the magnetic field in the solenoid capture system without adversely affecting the pion production efficiency. We show estimates of the amount of concrete shielding that will be required to protect the environment from the high radiation doses generated by the target station facility. We also present yield and energy deposition results for alternative targets: gallium liquid jet, tungsten powder jet, and solid tungsten bars.

  1. Closed-Loop Process Control for Electron Beam Freeform Fabrication and Deposition Processes

    Science.gov (United States)

    Taminger, Karen M. (Inventor); Hafley, Robert A. (Inventor); Martin, Richard E. (Inventor); Hofmeister, William H. (Inventor)

    2013-01-01

    A closed-loop control method for an electron beam freeform fabrication (EBF(sup 3)) process includes detecting a feature of interest during the process using a sensor(s), continuously evaluating the feature of interest to determine, in real time, a change occurring therein, and automatically modifying control parameters to control the EBF(sup 3) process. An apparatus provides closed-loop control method of the process, and includes an electron gun for generating an electron beam, a wire feeder for feeding a wire toward a substrate, wherein the wire is melted and progressively deposited in layers onto the substrate, a sensor(s), and a host machine. The sensor(s) measure the feature of interest during the process, and the host machine continuously evaluates the feature of interest to determine, in real time, a change occurring therein. The host machine automatically modifies control parameters to the EBF(sup 3) apparatus to control the EBF(sup 3) process in a closed-loop manner.

  2. Nanostructured Thin Film Synthesis by Aerosol Chemical Vapor Deposition for Energy Storage Applications

    Science.gov (United States)

    Chadha, Tandeep S.

    Renewable energy sources offer a viable solution to the growing energy demand while mitigating concerns for greenhouse gas emissions and climate change. This has led to a tremendous momentum towards solar and wind-based energy harvesting technologies driving efficiencies higher and costs lower. However, the intermittent nature of these energy sources necessitates energy storage technologies, which remain the Achilles heel in meeting the renewable energy goals. This dissertation focusses on two approaches for addressing the needs of energy storage: first, targeting direct solar to fuel conversion via photoelectrochemical water-splitting and second, improving the performance of current rechargeable batteries by developing new electrode architectures and synthesis processes. The aerosol chemical vapor deposition (ACVD) process has emerged as a promising single-step approach for nanostructured thin film synthesis directly on substrates. The relationship between the morphology and the operating parameters in the process is complex. In this work, a simulation based approach has been developed to understand the relationship and acquire the ability of predicting the morphology. These controlled nanostructured morphologies of TiO2 , compounded with gold nanoparticles of various shapes, are used for solar water-splitting applications. Tuning of light absorption in the visible-light range along with reduced electron-hole recombination in the composite structures has been demonstrated. The ACVD process is further extended to a novel single-step synthesis of nanostructured TiO2 electrodes directly on the current collector for applications as anodes in lithium-ion batteries, mainly for electric vehicles and hybrid electric vehicles. The effect of morphology of the nanostructures has been investigated via experimental studies and electrochemical transport modelling. Results demonstrate the exceptional performance of the single crystal one-dimensional nanostructures over granular

  3. Corrosion And Thermal Processing In Cold Gas Dynamic Spray Deposited Austenitic Stainless Steel Coatings

    Science.gov (United States)

    2016-06-01

    REPORT TYPE AND DATES COVERED Master’s thesis 4. TITLE AND SUBTITLE CORROSION AND THERMAL PROCESSING IN COLD GAS DYNAMIC SPRAY DEPOSITED AUSTENITIC...THERMAL PROCESSING IN COLD GAS DYNAMIC SPRAY DEPOSITED AUSTENITIC STAINLESS STEEL COATINGS by John A Luhn June 2016 Thesis Advisor: Sarath...precipitate. The resolution of the EDS process may not have been sufficient to show very small precipitates however. SEM imaging at higher

  4. Incident energy and charge deposition dependences of electron transmission through a microsized tapered glass capillary

    Energy Technology Data Exchange (ETDEWEB)

    Wickramarachchi, S.J. [Department of Physics, Western Michigan University, Kalamazoo, MI 49008 (United States); Ikeda, T. [RIKEN Nishina Center for Accelerator Based Science, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Dassanayake, B.S. [Department of Physics, Faculty of Science, University of Peradeniya (Sri Lanka); Keerthisinghe, D.; Tanis, J.A. [Department of Physics, Western Michigan University, Kalamazoo, MI 49008 (United States)

    2016-09-01

    An experimental study of electron transmission and guiding through a tapered glass capillary has been performed. Electrons were transmitted for tilt angles up to ∼6.5° and ∼9.5° (laboratory angles) for incident energies of 500 and 1000 eV, respectively. It is found that elastic and inelastic contributions give rise to distinguishable peaks in the transmitted profile. For 500 eV elastic transmission dominates the profile, while for 1000 eV both elastic and inelastic contributions are present. The transmission for both energies was studied as a function of the charge (time) deposition and found to be strongly dependent. Results suggest fundamental differences between 500 and 1000 eV incident electrons. For 500 eV the transmission slowly increases suggesting charge up of the capillary wall, reaching relative stability with infrequent breakdowns for all angles investigated. For 1000 eV for tilt angles near zero degrees the time dependent profile shows oscillations in the transmission, which never reached a stable condition, while for the larger angle investigated the transmission reached near equilibrium. Inelastic processes dominated the transmission for 1000 eV even at very small tilt angles, but was generally elastic (due to Coulomb deflection) for 500 eV even for the largest tilt angle measured.

  5. High-throughput processes for industrially scalable deposition of zinc oxide at atmospheric pressure

    NARCIS (Netherlands)

    Illiberi, A.; Grob, F.; Kniknie, B.; Frijters, C.; Deelen, J. van; Poodt, P.; Beckers, E.H.A.; Bolt, P.J.

    2014-01-01

    ZnO films have been grown on a moving glass substrate by high temperature (480 0C) chemical vapour deposition (CVD) and low temperature (200 0C) plasma enhanced CVD (PE-CVD) process at atmospheric pressure. Deposition rates above 7 nm/s have been achieved for substrate speeds from 20 to 500 mm/min.

  6. Inductive-Dynamic Simulation on Locations of Energy Input to and Deposition in the Ionosphere-Thermospher

    Science.gov (United States)

    Tu, J.

    2015-12-01

    Recent observations of the net Poynting flux deposition to the ionosphere showed that the strongest energy input from the magnetosphere is in the polar cap where the plasma flow speed is high and not where the flow reverses, implying that the field-aligned current is not the primary agent of the energy transfer and that other physical progresses are at play. In this study we assess locations of the energy transfer and deposition by a simulation conducted with a self-consistent inductive-dynamic (including self-consistent solutions of Faraday's law and retaining inertia terms in the plasma momentum equations) ionosphere-thermosphere model. In a 2-D global geometry (dawn-dusk meridian plane), we solve the multifluid-collisional-Hall MHD equations including photochemistry. The preliminary simulation results demonstrate propagation and evolution of the field-aligned currents and the dynamic processes of the formation of the ionospheric Pedersen currents. By comparing locations of the field-aligned currents and ionosphere/thermosphere heating driven by the magnetospheric convection we show that the energy input to the IT system and the energy dissipation occurs in the polar cap instead of regions where the field-aligned currents reside. The implication of these results is that the field-aligned currents are not the primary agent of the energy transfer from the magnetosphere to the IT system.

  7. Energy conservation by reducing process variability

    Energy Technology Data Exchange (ETDEWEB)

    Wising, Ulrika; Lafourcade, Sebastien [Pepite S.A., Liege (Belgium); Mack, Philippe [Pepite Technologies Inc., Montreal (Canada)

    2011-12-21

    Energy conservation is becoming an increasingly important instrument to stay competitive in today is increasingly global market. Important investments have been made in infrastructure and personnel in order to improve the management of energy such as increased metering, energy dashboards, energy managers, etc. Despite these investments, the results have not materialized and there is still a significant potential to further reduce energy consumption. In this paper a new methodology will be presented that helps industry better operate existing assets in order to reduce energy consumption, without having to make capital investments. The methodology uses a combination of advanced data analysis tools and a specific implementation scheme that has lead to significant savings in industry. The advanced data analysis tools are used to analyze the variability of the process in order to assess when the plant has been operated well or not so well in the past. By finding the root causes of these variations and the key variables that can explain them, improved operating guidelines and models can be developed and implemented. The specific implementation scheme is an important part of the methodology as it involves the people operating the plant. Several user cases will be presented showing an energy conservation of between 10%-20% without capital investments necessary. (author)

  8. Performance characterization of Ni60-WC coating on steel processed with supersonic laser deposition

    Directory of Open Access Journals (Sweden)

    Fang Luo

    2015-03-01

    Full Text Available Ni60-WC particles are used to improve the wear resistance of hard-facing steel due to their high hardness. An emerging technology that combines laser with cold spraying to deposit the hard-facing coatings is known as supersonic laser deposition. In this study, Ni60-WC is deposited on low-carbon steel using SLD. The microstructure and performance of the coatings are investigated through SEM, optical microscopy, EDS, XRD, microhardness and pin-on-disc wear tests. The experimental results of the coating processed with the optimal parameters are compared to those of the coating deposited using laser cladding.

  9. Lightweight, high-opacity paper : process costs and energy use reduction

    Science.gov (United States)

    John H. Klungness; Fabienne. Pianta; Mathew L. Stroika; Marguerite. Sykes; Freya. Tan; Said. AbuBakr

    1999-01-01

    Fiber loading is an environmentally friendly, energy efficient, and economical method for depositing precipitated calcium carbonate (PCC) partly within pulp fibers. Fiber loading can easily be done within the existing pulp processing system. This paper is a review of the process development from bench-scale to industrial-scale demonstrations, with additional...

  10. Experimental investigation on the energy deposition and expansion rate under the electrical explosion of aluminum wire in vacuum

    Science.gov (United States)

    Shi, Zongqian; Wang, Kun; Shi, Yuanjie; Wu, Jian; Han, Ruoyu

    2015-12-01

    Experimental investigations on the electrical explosion of aluminum wire using negative polarity current in vacuum are presented. Current pulses with rise rates of 40 A/ns, 80 A/ns, and 120 A/ns are generated for investigating the influence of current rise rate on energy deposition. Experimental results show a significant increase of energy deposition into the wire before the voltage breakdown with the increase of current rise rate. The influence of wire dimension on energy deposition is investigated as well. Decreasing the wire length allows more energy to be deposited into the wire. The energy deposition of a 0.5 cm-long wire explosion is ˜2.5 times higher than the energy deposition of a 2 cm-long wire explosion. The dependence of the energy deposition on wire diameter demonstrates a maximum energy deposition of 2.7 eV/atom with a diameter of ˜18 μm. Substantial increase in energy deposition is observed in the electrical explosion of aluminum wire with polyimide coating. A laser probe is applied to construct the shadowgraphy, schlieren, and interferometry diagnostics. The morphology and expansion trajectory of exploding products are analyzed based on the shadowgram. The interference phase shift is reconstructed from the interferogram. Parallel dual wires are exploded to estimate the expansion velocity of the plasma shell.

  11. Scaling behavior and morphological properties of the interfaces obtained by the multilayer deposition process

    Energy Technology Data Exchange (ETDEWEB)

    Achik, I. [Laboratoire de Physique de la Matière Condensée, Université Hassan II-Mohammedia, Faculté des sciences Ben M' sik, Casablanca (Morocco); Boughaleb, Y., E-mail: yboughaleb@yahoo.fr [Laboratoire de Physique de la Matière Condensée, Université Hassan II-Mohammedia, Faculté des sciences Ben M' sik, Casablanca (Morocco); Université Chouaib Doukkali, Faculté des sciences, El Jadida (Morocco); Hassan II Academy of Science and Technology, Rabat (Morocco); Hader, A. [Laboratoire de Physique de la Matière Condensée, Université Hassan II-Mohammedia, Faculté des sciences Ben M' sik, Casablanca (Morocco); CRMEF Settat (Morocco); Sbiaai, K. [Université Chouaib Doukkali, Faculté des sciences, El Jadida (Morocco); Hajjaji, A. [Université Chouaib Doukkali, Ecole nationale des sciences appliquées, El Jadida (Morocco)

    2013-10-31

    The aim of the present work was to study numerically the scaling behavior and the morphological properties of the interfaces generated by the multilayer deposition process. We have noticed that, in the case where the ratio of the surface diffusion coefficient to the deposition rate reaches high values D/F > > 1, the interface consists of mound structures. By using the dynamic scaling, we have shown that the height–height correlation function scales with time t and length l as G(l,t) ∼ l{sup α}f(t/l{sup α/β}) with β = 0.25 ± 0.05 and α = 0.51 ± 0.02. These exponent values are equal to the ones predicted by the Edwards–Wilkinson approach. Besides, our results are in agreement with the growth system of Cu/Cu(100) at 300 K which has been characterized in more detail by a combined scanning tunneling microscopy and spot profile analysis — low energy electronic diffusion study. Moreover, by considering two different methods, we have examined the fractal aspect of the obtained interfaces. - Highlights: • The adlayer interfaces present mound morphologies. • The adlayer interfaces scale with the Family–Vicsek law. • The critical exponents (α, β) are in agreement with those of Edwards–Wilkinson approach.

  12. Fermi energy shift in deposited metallic nanotubes: A Raman scattering study

    Science.gov (United States)

    Hatting, Benjamin; Heeg, Sebastian; Ataka, Kenichi; Heberle, Joachim; Hennrich, Frank; Kappes, Manfred M.; Krupke, Ralph; Reich, Stephanie

    2013-04-01

    The longitudinal optical phonon of metallic nanotubes shifts by 23 cm-1 to higher energies when the nanotubes are deposited onto a substrate. The linewidth narrows by 13 cm-1. The changes are explained in terms of shifts in the Fermi energy that influence the Kohn anomaly in the longitudinal optical phonon branch in metallic nanotubes. Using in situ electrochemical Raman measurements we show that the Fermi energy is 0.16 eV below its intrinsic value in metallic nanotubes in solution. Our results impact the application of Raman spectroscopy to distinguish between metallic and semiconducting tubes by examining the high-energy mode line shape.

  13. Reactive Ar ion beam sputter deposition of TiO{sub 2} films: Influence of process parameters on film properties

    Energy Technology Data Exchange (ETDEWEB)

    Bundesmann, C., E-mail: carsten.bundesmann@iom-leipzig.de [Leibniz-Institut für Oberflächenmodifizierung e.V., Permoserstrasse 15, 04318 Leipzig (Germany); Lautenschläger, T.; Thelander, E. [Leibniz-Institut für Oberflächenmodifizierung e.V., Permoserstrasse 15, 04318 Leipzig (Germany); Spemann, D. [Leibniz-Institut für Oberflächenmodifizierung e.V., Permoserstrasse 15, 04318 Leipzig (Germany); Universität Leipzig, Fakultät für Physik und Geowissenschaften, Institut für Experimentelle Physik II, Linnéstrasse 5, 04103 Leipzig (Germany)

    2017-03-15

    Highlights: • Ion beam sputter deposition under systematic variation of process parameters. • Thickness, growth rate, structure, mass density, composition, optical properties. • All TiO{sub 2} films are amorphous with systematic variations in mass density. • Considerable amount of inert process gas correlated with scattering angle. • Correlation of mass density and index of refraction. - Abstract: Several sets of TiO{sub 2} films were grown by Ar ion beam sputter deposition under systematic variation of ion energy and geometrical parameters (ion incidence angle and polar emission angle). The films were characterized concerning thickness, growth rate, structural properties, composition, mass density, and optical properties. The film thicknesses show a cosine-like angular distribution, and the growth rates were found to increase with increasing ion incidence angle and ion energy. All films are amorphous and stoichiometric, but can contain a considerable amount of backscattered primary particles. The atomic fraction of Ar particles decreases systematically with increasing scattering angle, independent from ion energy and ion incidence angle. Mass density and index of refraction show similar systematic variations with ion energy and geometrical parameters. The film properties are mainly influenced by the scattering geometry, and only slightly by ion energy and ion incidence angle. The variations in the film properties are tentatively assigned to changes in the angular and energy distribution of the sputtered target particles and back-scattered primary particles.

  14. The Research and Development of the External Magnetic Field Acting on Electro-Deposition Process

    Directory of Open Access Journals (Sweden)

    Wu Menghua

    2016-01-01

    Full Text Available The research and development status of the electro-deposition technology under the action of external magnetic field are introduced. The basic characteristics and applied manners of external magnetic field in electro-deposition process are summarized. The acting principle of external magnetic field, the effects of magnetic hydrodynamics (MHD caused by the Lorentz force, and the acting of magnetic force on the metal ions and particles are described. The main actions of external magnetic field include MHD effect, magnetizing force, affecting the physical and chemical properties of the bath, affecting the disperse ability and coverage capacity of bath, affecting the mass transfer process of electro-deposition, affecting the chemical reaction process and current distribution of electrode surface. Some examples of electro-depositing single metal coatings, alloy coatings and composite coatings under action of magnetic field are explained. During the electro-depositing process, the external magnetic field has different degrees of impact on solution properties, mass transfer, charge transfer, content of composited nanoparticles, crystal growth and crystal orientation etc. The specific impact of magnetic field during the electro-depositing is also classified and summarized. The problems that existed in electro-deposition process while applying magnetic field and the next development trend were summarized.

  15. Balancing Energy Processes in Turbine Engines

    Directory of Open Access Journals (Sweden)

    Balicki Włodzimierz

    2015-01-01

    Full Text Available The article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and marine propulsion systems with the aim to analyse and evaluate basic operating parameters. The first part presents the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect of flow parameters and constructional properties of the engines on their performance and real efficiency are evaluated. The second part of the article, devoted to marine applications of turbine engines, presents the energy balance of the kinetic system of torque transmission from main engine turbines to screw propellers in the combined system of COGAG type. The physical model of energy conversion processes executed in this system is presented, along with the physical model of gasodynamic processes taking place in a separate driving turbine of a reversing engine. These models have made the basis for formulating balance equations, which then were used for analysing static and dynamic properties of the analysed type of propulsion, in particular in the aspect of mechanical loss evaluation in its kinematic system.

  16. Energy deposition characteristics of nanosecond dielectric barrier discharge plasma actuators : Influence of dielectric material

    NARCIS (Netherlands)

    Correale, G.; Winkel, R.; Kotsonis, M.

    2015-01-01

    An experimental study aimed at the characterization of energy deposition of nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuators was carried out. Special attention was given on the effect of the thickness and material used for dielectric barrier. The selected materials for this study

  17. Impact of parametric uncertainty on estimation of the energy deposition into an irradiated brain tumor

    Science.gov (United States)

    Taverniers, Søren; Tartakovsky, Daniel M.

    2017-11-01

    Predictions of the total energy deposited into a brain tumor through X-ray irradiation are notoriously error-prone. We investigate how this predictive uncertainty is affected by uncertainty in both the location of the region occupied by a dose-enhancing iodinated contrast agent and the agent's concentration. This is done within the probabilistic framework in which these uncertain parameters are modeled as random variables. We employ the stochastic collocation (SC) method to estimate statistical moments of the deposited energy in terms of statistical moments of the random inputs, and the global sensitivity analysis (GSA) to quantify the relative importance of uncertainty in these parameters on the overall predictive uncertainty. A nonlinear radiation-diffusion equation dramatically magnifies the coefficient of variation of the uncertain parameters, yielding a large coefficient of variation for the predicted energy deposition. This demonstrates that accurate prediction of the energy deposition requires a proper treatment of even small parametric uncertainty. Our analysis also reveals that SC outperforms standard Monte Carlo, but its relative efficiency decreases as the number of uncertain parameters increases from one to three. A robust GSA ameliorates this problem by reducing this number.

  18. A General Relativistic Ray-tracing Method for Estimating the Energy and Momentum Deposition by Neutrino Pair Annihilation in Collapsars

    Science.gov (United States)

    Harikae, Seiji; Kotake, Kei; Takiwaki, Tomoya; Sekiguchi, Yu-ichiro

    2010-09-01

    Bearing in mind the application to the collapsar models of gamma-ray bursts (GRBs), we develop a numerical scheme and code for estimating the deposition of energy and momentum due to the neutrino pair annihilation (ν + {\\bar{ν}} → e^{-} + e^{+}) in the vicinity of an accretion tori around a Kerr black hole. Our code is designed to solve the general relativistic (GR) neutrino transfer by a ray-tracing method. To solve the collisional Boltzmann equation in curved spacetime, we numerically integrate the so-called rendering equation along the null geodesics. We employ the Fehlberg (4,5) adaptive integrator in the Runge-Kutta method to perform the numerical integration accurately. For the neutrino opacity, the charged-current β-processes, which are dominant in the vicinity of the accretion tori, are taken into account. The numerical accuracy of the developed code is certified by several tests in which we show comparisons with the corresponding analytical solutions. In order to solve the energy-dependent ray-tracing transport, we propose that an adaptive-mesh-refinement approach, which we take for the two radiation angles (θ, phi) and the neutrino energy, is useful in reducing the computational cost significantly. Based on the hydrodynamical data in our collapsar simulation, we estimate the annihilation rates in a post-processing manner. Increasing the Kerr parameter from 0 to 1, it is found that the GR effect can increase the local energy deposition rate by about one order of magnitude, and the net energy deposition rate by several tens of percent. After the accretion disk settles into a stationary state (typically later than ~9 s from the onset of gravitational collapse), we point out that the neutrino-heating timescale in the vicinity of the polar funnel region can be shorter than the dynamical timescale. Our results suggest that the neutrino pair annihilation is potentially as important as the conventional magnetohydrodynamic mechanism for igniting the GRB

  19. On the determination of energy fluxes at plasma-surface processes

    Energy Technology Data Exchange (ETDEWEB)

    Kersten, H.; Rohde, D.; Steffen, H.; Deutsch, H.; Hippler, R. [Greifswald Univ. (Germany). Inst. fuer Physik; Swinkels, G.H.P.M.; Kroesen, G.M.W. [Technische Univ. Eindhoven (Netherlands). Dept. of Physics

    2001-05-01

    A summary is given of different methods for the determination of the energy influx and its influence on the thermal balance and energetic conditions of substrate surfaces during plasma processing. The discussed mechanisms include heat radiation and kinetic and potential energy of charged particles and sputtered neutrals. For a few examples such as magnetron sputtering of a-C:H films, sputter deposition of aluminum on microparticles, and titanium deposition in a hollow-cathode arc evaporation device the energetic balance of substrates during plasma processing is presented. (orig.)

  20. Energy optimization of integrated process plants

    Energy Technology Data Exchange (ETDEWEB)

    Sandvig Nielsen, J.

    1996-10-01

    A general approach for viewing the process synthesis as an evolutionary process is proposed. Each step is taken according to the present level of information and knowledge. This is formulated in a Process Synthesis Cycle. Initially the synthesis is conducted at a high abstraction level maximizing use of heuristics (prior experience, rules of thumbs etc). When further knowledge and information are available, heuristics will gradually be replaced by exact problem formulations. The principles in the Process Synthesis Cycle, is used to develop a general procedure for energy synthesis, based on available tools. The procedure is based on efficient use of process simulators with integrated Pinch capabilities (energy targeting). The proposed general procedure is tailored to three specific problems (Humid Air Turbine power plant synthesis, Nitric Acid process synthesis and Sulphuric Acid synthesis). Using the procedure reduces the problem dimension considerable and thus allows for faster evaluation of more alternatives. At more detailed level a new framework for the Heat Exchanger Network synthesis problem is proposed. The new framework is object oriented based on a general functional description of all elements potentially present in the heat exchanger network (streams, exchangers, pumps, furnaces etc.). (LN) 116 refs.

  1. Energy Dissipation Processes in Solar Wind Turbulence

    Science.gov (United States)

    Wang, Y.; Wei, F. S.; Feng, X. S.; Xu, X. J.; Zhang, J.; Sun, T. R.; Zuo, P. B.

    2015-12-01

    Turbulence is a chaotic flow regime filled by irregular flows. The dissipation of turbulence is a fundamental problem in the realm of physics. Theoretically, dissipation ultimately cannot be achieved without collisions, and so how turbulent kinetic energy is dissipated in the nearly collisionless solar wind is a challenging problem. Wave particle interactions and magnetic reconnection (MR) are two possible dissipation mechanisms, but which mechanism dominates is still a controversial topic. Here we analyze the dissipation region scaling around a solar wind MR region. We find that the MR region shows unique multifractal scaling in the dissipation range, while the ambient solar wind turbulence reveals a monofractal dissipation process for most of the time. These results provide the first observational evidences for intermittent multifractal dissipation region scaling around a MR site, and they also have significant implications for the fundamental energy dissipation process.

  2. ENERGY DISSIPATION PROCESSES IN SOLAR WIND TURBULENCE

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Y.; Wei, F. S.; Feng, X. S.; Sun, T. R.; Zuo, P. B. [SIGMA Weather Group, State Key Laboratory for Space Weather, National Space Science Center, Chinese Academy of Sciences, Beijing 100190 (China); Xu, X. J. [Space Science Institute, Macau University of Science and Technology, Macao (China); Zhang, J., E-mail: yw@spaceweather.ac.cn [School of Physics, Astronomy and Computational Sciences, George Mason University, 4400 University Drive, MSN 3F3, Fairfax, Virginia 22030 (United States)

    2015-12-15

    Turbulence is a chaotic flow regime filled by irregular flows. The dissipation of turbulence is a fundamental problem in the realm of physics. Theoretically, dissipation ultimately cannot be achieved without collisions, and so how turbulent kinetic energy is dissipated in the nearly collisionless solar wind is a challenging problem. Wave particle interactions and magnetic reconnection (MR) are two possible dissipation mechanisms, but which mechanism dominates is still a controversial topic. Here we analyze the dissipation region scaling around a solar wind MR region. We find that the MR region shows unique multifractal scaling in the dissipation range, while the ambient solar wind turbulence reveals a monofractal dissipation process for most of the time. These results provide the first observational evidences for intermittent multifractal dissipation region scaling around a MR site, and they also have significant implications for the fundamental energy dissipation process.

  3. Investigation of various energy deposition kernel refinements for the convolution/superposition method

    Science.gov (United States)

    Huang, Jessie Y.; Eklund, David; Childress, Nathan L.; Howell, Rebecca M.; Mirkovic, Dragan; Followill, David S.; Kry, Stephen F.

    2013-01-01

    found that depth was the most dominant factor affecting the pattern of energy deposition; however, the effects of field size and off-axis distance were not negligible. For the material-specific kernels, we found that as the density of the material increased, more energy was deposited laterally by charged particles, as opposed to in the forward direction. Thus, density scaling of water kernels becomes a worse approximation as the density and the effective atomic number of the material differ more from water. Implementation of spatially variant, polyenergetic kernels increased the percent depth dose value at 25 cm depth by 2.1%–5.8% depending on the field size, while implementation of titanium kernels gave 4.9% higher dose upstream of the metal cavity (i.e., higher backscatter dose) and 8.2% lower dose downstream of the cavity. Conclusions: Of the various kernel refinements investigated, inclusion of depth-dependent and metal-specific kernels into the C/S method has the greatest potential to improve dose calculation accuracy. Implementation of spatially variant polyenergetic kernels resulted in a harder depth dose curve and thus has the potential to affect beam modeling parameters obtained in the commissioning process. For metal implants, the C/S algorithms generally underestimate the dose upstream and overestimate the dose downstream of the implant. Implementation of a metal-specific kernel mitigated both of these errors. PMID:24320507

  4. Film Growth Rates and Activation Energies for Core-Shell Nanoparticles Derived from a CVD Based Aerosol Process

    OpenAIRE

    Frederik Weis; Martin Seipenbusch; Gerhard Kasper

    2015-01-01

    Silica core-shell nanoparticles of about 60–120 nm with a closed outer layer of bismuth or molybdenum oxide of 1–10 nm were synthesized by an integrated chemical vapor synthesis/chemical vapor deposition process at atmospheric pressure. Film growth rates and activation energies were derived from transmission electron microscopy (TEM) images for a deposition process based on molybdenum hexacarbonyl and triphenyl bismuth as respective coating precursors. Respective activation energies of 123 ±...

  5. Image processing to optimize wave energy converters

    Science.gov (United States)

    Bailey, Kyle Marc-Anthony

    The world is turning to renewable energies as a means of ensuring the planet's future and well-being. There have been a few attempts in the past to utilize wave power as a means of generating electricity through the use of Wave Energy Converters (WEC), but only recently are they becoming a focal point in the renewable energy field. Over the past few years there has been a global drive to advance the efficiency of WEC. Placing a mechanical device either onshore or offshore that captures the energy within ocean surface waves to drive a mechanical device is how wave power is produced. This paper seeks to provide a novel and innovative way to estimate ocean wave frequency through the use of image processing. This will be achieved by applying a complex modulated lapped orthogonal transform filter bank to satellite images of ocean waves. The complex modulated lapped orthogonal transform filterbank provides an equal subband decomposition of the Nyquist bounded discrete time Fourier Transform spectrum. The maximum energy of the 2D complex modulated lapped transform subband is used to determine the horizontal and vertical frequency, which subsequently can be used to determine the wave frequency in the direction of the WEC by a simple trigonometric scaling. The robustness of the proposed method is provided by the applications to simulated and real satellite images where the frequency is known.

  6. A sub-atmospheric chemical vapor deposition process for deposition of oxide liner in high aspect ratio through silicon vias.

    Science.gov (United States)

    Lisker, Marco; Marschmeyer, Steffen; Kaynak, Mehmet; Tekin, Ibrahim

    2011-09-01

    The formation of a Through Silicon Via (TSV) includes a deep Si trench etching and the formation of an insulating layer along the high-aspect-ratio trench and the filling of a conductive material into the via hole. The isolation of the filling conductor from the silicon substrate becomes more important for higher frequencies due to the high coupling of the signal to the silicon. The importance of the oxide thickness on the via wall isolation can be verified using electromagnetic field simulators. To satisfy the needs on the Silicon dioxide deposition, a sub-atmospheric chemical vapor deposition (SA-CVD) process has been developed to deposit an isolation oxide to the walls of deep silicon trenches. The technique provides excellent step coverage of the 100 microm depth silicon trenches with the high aspect ratio of 20 and more. The developed technique allows covering the deep silicon trenches by oxide and makes the high isolation of TSVs from silicon substrate feasible which is the key factor for the performance of TSVs for mm-wave 3D packaging.

  7. Hydrochemical processes in mine waste deposits and drainage water - Heavy metal speciation, sorption and sedimentation processes

    Energy Technology Data Exchange (ETDEWEB)

    Loevgren, L.; Sjoeberg, S. [Umeaa Univ. (Sweden). Dept. of Inorganic Chemistry

    1997-12-31

    The aim of the present project has been to quantitatively describe hydrochemical processes relevant for the retention and mobility of heavy metals in mine waste deposits. The activities have been focused on the solubility and speciation of Pb(II), Cd(II), Cu(II), Zn(II), CR(VI) and As(III,V). Main attention has been paid to adsorption processes at the surfaces of iron (hydr)oxides (goethite, et-FeOOH). The main experimental methods for studying the adsorption reactions have been potentiometric titrations and batch adsorption experiments. Experimental data have been evaluated in terms of models for surface complexation equilibria, which can be used in hydrogeochemical model calculations of processes within the deposits as well as in the recipients of drainage water. Furthermore, in several cases the surface complexes formed have been characterized structurally by means of Fourier Transform-Infrared spectroscopy. In order to test the validity of the equilibrium models obtained at millimolar concentrations of both sorbate and sorbent a new method utilizing Anodic Stripping Voltammetry as an in situ probe in titrations has been developed within the project. A particular interest has been given to the influence of complexing inorganic and organic anions on the adsorption of the heavy metal ions. The presence of sulfate ions resulted in a moderate increased adsorption of Cu(II) and Pb(II) under acidic conditions, while the adsorption of Zn(II) remained uninfluenced. The increased adsorption could be explained by reduced electrostatic repulsion between positively charged surfaces and metal ions, and by formation of ternary surface complexes. Similar mechanisms could explain the data in the goethite-Me(II)- carboxylate systems. The organic acids study are: phthalic acid, trimellitic acid and pyromellitic acid, which are aromatic acids with two, three and four carboxylate groups, respectively. Before the experimental data in the organic containing systems could be

  8. Study of Energy Deposition and Activation for the LINAC4 Dump

    CERN Document Server

    Cerutti, F; Mauro, E; Mereghetti, A; Silari, M; CERN. Geneva. AB Department

    2008-01-01

    This document provides estimates of energy deposition and activation for the dump of the future LINAC4 accelerator. Detailed maps of power density deposited in the dump are given, allowing to perform further thermo mechanical studies. Residual dose rates at a few cooling times for different irradiation scenarios have been calculated. Moreover, the air activation has been evaluated and doses to the reference population group and to a worker intervening in the cave at the shutdown have been predicted. Calculations were performed with the Monte Carlo particle transport and interaction code FLUKA.

  9. Lime-mud layers in high-energy tidal channels: A record of hurricane deposition

    Science.gov (United States)

    Shinn, E.A.; Steinen, R.P.; Dill, R.F.; Major, R.

    1993-01-01

    During or immediately following the transit of Hurricane Andrew (August 23-24, 1992) across the northern part of the Great Bahama Bank, thin laminated beds of carbonate mud were deposited in high-energy subtidal channels (4 m depth) through the ooid shoals of south Cat Cay and Joulters Cays. Thicker, more cohesive (and therefore older) mud beds and angular mud fragments associated with ooids from Joulters Cays have similar characteristics but lack fresh plant fragments. We infer that these older beds were similarly deposited and thus record the passage of previous hurricanes or tropical storms. -from Authors

  10. The erosion performance of cold spray deposited metal matrix composite coatings with subsequent friction stir processing

    Science.gov (United States)

    Peat, Tom; Galloway, Alexander; Toumpis, Athanasios; McNutt, Philip; Iqbal, Naveed

    2017-02-01

    This study forms an initial investigation into the development of SprayStir, an innovative processing technique for generating erosion resistant surface layers on a chosen substrate material. Tungsten carbide - cobalt chromium, chromium carbide - nickel chromium and aluminium oxide coatings were successfully cold spray deposited on AA5083 grade aluminium. In order to improve the deposition efficiency of the cold spray process, coatings were co-deposited with powdered AA5083 using a twin powder feed system that resulted in thick (>300 μm) composite coatings. The deposited coatings were subsequently friction stir processed to embed the particles in the substrate in order to generate a metal matrix composite (MMC) surface layer. The primary aim of this investigation was to examine the erosion performance of the SprayStirred surfaces and demonstrate the benefits of this novel process as a surface engineering technique. Volumetric analysis of the SprayStirred surfaces highlighted a drop of approx. 40% in the level of material loss when compared with the cold spray deposited coating prior to friction stir processing. Micro-hardness testing revealed that in the case of WC-CoCr reinforced coating, the hardness of the SprayStirred material exhibits an increase of approx. 540% over the unaltered substrate and 120% over the as-deposited composite coating. Microstructural examination demonstrated that the increase in the hardness of the MMC aligns with the improved dispersion of reinforcing particles throughout the aluminium matrix.

  11. In-situ observation of particles deposition process on a ferromagnetic filter during high-gradient magnetic separation process

    Energy Technology Data Exchange (ETDEWEB)

    Hirota, Noriyuki, E-mail: hirota.noriyuki@nims.go.jp [Fine Particle Engineering Group, National Institute for Materials Science, 3-13 Sakura, Tsukuba (Japan); Ando, Tsutomu; Takano, Tadamitsu [Department of Mechanical Engineering, Nihon University, 1-2-1 Izumicho, Narashino 275-8575 (Japan); Okada, Hidehiko [Fine Particle Engineering Group, National Institute for Materials Science, 3-13 Sakura, Tsukuba (Japan)

    2017-04-01

    Abstracts: In-situ observations of particles deposition process on a ferromagnetic filter in high gradient magnetic separation were carried out under high magnetic fields to obtain information for the optimization of separation condition. The spike-like deposition structure was observed on the upper stream of the magnetic filter, different from the conventional deposition image obtained for paramagnetic particles. The length of the spike structure tends to be long with lower flow velocity and lower applied magnetic field. It was also observed that the chain structure or the bundle of such chaines were formed on the way to the filter under the condition of the low applied magnetic field and low flow rates. Results obtained here indicate that the effect of deposited particles on the spatial distribution of the magnetic field and the hydrodynamics, they are often ignored in the simulation so far, should be considered appropriately. - Highlights: • In-situ observation of particles deposition process on a ferromagnetic filter in HGMS. • The spike-like deposition structure was observed on the upper stream. • Longer spike structure formed under lower magnetic fields and lower flow rates. • Effect of the magnetization of deposited particles should be considered appropriately.

  12. Adhesion promoting polymerinterlayers for Ag layers deposited in OLED processing

    OpenAIRE

    Vicca P.; Steudel S.; Genoe J.; Heremans P.

    2010-01-01

    One of the main drivers for organic electronic research are the backplanes for flexible active-matrix displays using organic light-emitting diodes (AM-OLEDs). In our work, we processed organic thin-film transistors (OTFTs) at low temperatures (

  13. Particle fluxes and energy deposition in infinite homogeneous air due to protons of energy 1-, 5-, 10-, and 20-GeV

    Energy Technology Data Exchange (ETDEWEB)

    Gabriel, T. A.; Bishop, B. L.; Amburgey, J. D.; Barish, J.

    1977-12-01

    Calculations have been carried out to determine the spatial dependence of the energy deposition and the spatial and energy dependence of particle fluxes in infinite homogeneous air without hydrogen due to protons of energy 5-, 10-, and 20-GeV. The fluxes are broken down into nine particle types. The energy deposition is divided among seven categories. The spatial dependence of the energy deposition is also presented for 1- and 10-GeV protons incident on infinite homogeneous air with hydrogen. The spatially integrated production of various residual nuclei is included.

  14. Evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Sang Keun; Kim, Wook; Park, Yong Sung; Kang, Joo Hyun; Lee, Yong Jin [Korea Institute of Radiological and Medical Sciences, KIRAMS, Seoul (Korea, Republic of); Cho, Doo Wan; Lee, Hong Soo; Han, Su Cheol [Jeonbuk Department of Inhalation Research, Korea Institute of toxicology, KRICT, Jeongeup (Korea, Republic of)

    2016-12-15

    These absorbed dose can calculated using the Monte Carlo transport code MCNP (Monte Carlo N-particle transport code). Internal radiotherapy absorbed dose was calculated using conventional software, such as OLINDA/EXM or Monte Carlo simulation. However, the OLINDA/EXM does not calculate individual absorbed dose and non-standard organ, such as tumor. While the Monte Carlo simulation can calculated non-standard organ and specific absorbed dose using individual CT image. External radiotherapy, absorbed dose can calculated by specific absorbed energy in specific organs using Monte Carlo simulation. The specific absorbed energy in each organ was difference between species or even if the same species. Since they have difference organ sizes, position, and density of organs. The aim of this study was to individually evaluated cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. We evaluation of cobalt-60 energy deposit in mouse and monkey using Monte Carlo simulation. The absorbed energy in each organ compared with mouse heart was 54.6 fold higher than monkey absorbed energy in heart. Likewise lung was 88.4, liver was 16.0, urinary bladder was 29.4 fold higher than monkey. It means that the distance of each organs and organ mass was effects of the absorbed energy. This result may help to can calculated absorbed dose and more accuracy plan for external radiation beam therapy and internal radiotherapy.

  15. Improving dryer energy efficiency and controllability simultaneously by process modification

    NARCIS (Netherlands)

    Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

    2013-01-01

    This work establishes a relationship between dryer energy performance and controllability using energy balances and process resiliency analysis. It is shown that using the process gain matrix, the dryer energy efficiency can be reliably calculated with conditions for simultaneous controllability

  16. Investigation of various energy deposition kernel refinements for the convolution∕superposition method.

    Science.gov (United States)

    Huang, Jessie Y; Eklund, David; Childress, Nathan L; Howell, Rebecca M; Mirkovic, Dragan; Followill, David S; Kry, Stephen F

    2013-12-01

    negligible. For the material-specific kernels, we found that as the density of the material increased, more energy was deposited laterally by charged particles, as opposed to in the forward direction. Thus, density scaling of water kernels becomes a worse approximation as the density and the effective atomic number of the material differ more from water. Implementation of spatially variant, polyenergetic kernels increased the percent depth dose value at 25 cm depth by 2.1%-5.8% depending on the field size, while implementation of titanium kernels gave 4.9% higher dose upstream of the metal cavity (i.e., higher backscatter dose) and 8.2% lower dose downstream of the cavity. Of the various kernel refinements investigated, inclusion of depth-dependent and metal-specific kernels into the C∕S method has the greatest potential to improve dose calculation accuracy. Implementation of spatially variant polyenergetic kernels resulted in a harder depth dose curve and thus has the potential to affect beam modeling parameters obtained in the commissioning process. For metal implants, the C∕S algorithms generally underestimate the dose upstream and overestimate the dose downstream of the implant. Implementation of a metal-specific kernel mitigated both of these errors.

  17. Deposition and post-processing techniques for transparent conductive films

    Energy Technology Data Exchange (ETDEWEB)

    Christoforo, Mark Greyson; Mehra, Saahil; Salleo, Alberto; Peumans, Peter

    2017-07-04

    In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

  18. Deposition and post-processing techniques for transparent conductive films

    Energy Technology Data Exchange (ETDEWEB)

    Christoforo, Mark Greyson; Mehra, Saahil; Salleo, Alberto; Peumans, Peter

    2015-01-13

    In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

  19. Deposition conditions for the growth of textured ZnO thin films by aerosol CVD process

    OpenAIRE

    Deschanvres, J.-L.; Bochu, B.; Joubert, J.-C.

    1993-01-01

    The crystalline orientation of ZnO thin films deposited by an aerosol CVD process is studied with regard to the experimental conditions. The quality of the C-axis oriented growth depended on the substrate temperature, on the deposition rate and also on the hygrometric degree of the carrier gas. The quality of the gold sublayer influenced also the quality of the ZnO textured growth. Under a dry gas mixture N2-O2 at 495°C and with a deposition rate of 35Å/mn, the texture ratio was less than -3....

  20. Comparison of deposited surface area of airborne ultrafine particles generated from two welding processes.

    Science.gov (United States)

    Gomes, J F; Albuquerque, P C; Miranda, Rosa M; Santos, Telmo G; Vieira, M T

    2012-09-01

    This article describes work performed on the assessment of the levels of airborne ultrafine particles emitted in two welding processes metal-active gas (MAG) of carbon steel and friction-stir welding (FSW) of aluminium in terms of deposited area in alveolar tract of the lung using a nanoparticle surface area monitor analyser. The obtained results showed the dependence from process parameters on emitted ultrafine particles and clearly demonstrated the presence of ultrafine particles, when compared with background levels. The obtained results showed that the process that results on the lower levels of alveolar-deposited surface area is FSW, unlike MAG. Nevertheless, all the tested processes resulted in important doses of ultrafine particles that are to be deposited in the human lung of exposed workers.

  1. Deposition of polysilicon as an example of a pyrolytic CVD process

    Science.gov (United States)

    Korec, Jacek

    1980-07-01

    A model of a CVD process based on a pyrolytic reaction is presented. Various types of growth rate control by different elementary physical processes occuring during the deposition of the layer are discussed. The experimental data published for the deposition of polysilicon on amorphous SiO 2 by pyrolysis of SiH 4 in N 2 serves as an experimental verification of the theory. A formula describing the growth rate dependence on process parameters and conclusion concerning the definition of the diffusive region given by the model are in good agreement with the experiment.

  2. Effect of Source, Surfactant, and Deposition Process on Electronic Properties of Nanotube Arrays

    Directory of Open Access Journals (Sweden)

    Dheeraj Jain

    2011-01-01

    Full Text Available The electronic properties of arrays of carbon nanotubes from several different sources differing in the manufacturing process used with a variety of average properties such as length, diameter, and chirality are studied. We used several common surfactants to disperse each of these nanotubes and then deposited them on Si wafers from their aqueous solutions using dielectrophoresis. Transport measurements were performed to compare and determine the effect of different surfactants, deposition processes, and synthesis processes on nanotubes synthesized using CVD, CoMoCAT, laser ablation, and HiPCO.

  3. The Dark Energy Survey Image Processing Pipeline

    Energy Technology Data Exchange (ETDEWEB)

    Morganson, E.; et al.

    2018-01-09

    The Dark Energy Survey (DES) is a five-year optical imaging campaign with the goal of understanding the origin of cosmic acceleration. DES performs a 5000 square degree survey of the southern sky in five optical bands (g,r,i,z,Y) to a depth of ~24th magnitude. Contemporaneously, DES performs a deep, time-domain survey in four optical bands (g,r,i,z) over 27 square degrees. DES exposures are processed nightly with an evolving data reduction pipeline and evaluated for image quality to determine if they need to be retaken. Difference imaging and transient source detection are also performed in the time domain component nightly. On a bi-annual basis, DES exposures are reprocessed with a refined pipeline and coadded to maximize imaging depth. Here we describe the DES image processing pipeline in support of DES science, as a reference for users of archival DES data, and as a guide for future astronomical surveys.

  4. Sedimentary processes and depositional environments of the Horn River Shale in British Columbia, Canada

    Science.gov (United States)

    Yoon, Seok-Hoon; Koh, Chang-Seong; Joe, Young-Jin; Woo, Ju-Hwan; Lee, Hyun-Suk

    2017-04-01

    The Horn River Basin in the northeastern British Columbia, Canada, is one of the largest unconventional gas accumulations in North America. It consists mainly of Devonian shales (Horn River Formation) and is stratigraphically divided into three members, the Muskwa, Otterpark and Evie in descending order. This study focuses on sedimentary processes and depositional environments of the Horn River shale based on sedimentary facies analysis aided by well-log mineralogy (ECS) and total organic carbon (TOC) data. The shale formation consists dominantly of siliceous minerals (quartz, feldspar and mica) and subordinate clay mineral and carbonate materials, and TOC ranging from 1.0 to 7.6%. Based on sedimentary structures and micro texture, three sedimentary facies were classified: homogeneous mudstone (HM), indistinctly laminated mudstone (ILM), and planar laminated mudstone (PLM). Integrated interpretation of the sedimentary facies, lithology and TOC suggests that depositional environment of the Horn River shale was an anoxic quiescent basin plain and base-of-slope off carbonate platform or reef. In this deeper marine setting, organic-rich facies HM and ILM, dominant in the Muskwa (the upper part of the Horn River Formation) and Evie (the lower part of the Horn River Formation) members, may have been emplaced by pelagic to hemipelagic sedimentation on the anoxic sea floor with infrequent effects of low-density gravity flows (turbidity currents or nepheloid flows). In the other hand, facies PLM typifying the Otterpark Member (the middle part of the Horn River Formation) suggests more frequent inflow of bottom-hugging turbidity currents punctuating the hemipelagic settling of the background sedimentation process. The stratigraphic change of sedimentary facies and TOC content in the Horn River Formation is most appropriately interpreted to have been caused by the relative sea-level change, that is, lower TOC and frequent signal of turbidity current during the sea

  5. Energy harvesting based on piezoelectric AlN and AlScN thin films deposited by high rate sputtering

    Science.gov (United States)

    Frach, Peter; Barth, Stephan; Bartzsch, Hagen; Gloess, Daniel

    2017-05-01

    Aluminum nitride (AlN) is a piezoelectric material often used as thin film in SAW/BAW devices. Furthermore, there is an increasing interest in its use for energy harvesting applications. Despite it has a relatively low piezoelectric coefficient, it is a suitable choice for energy harvesting applications and due to its low dielectric constant and good mechanical properties. In addition, it is a lead-free material. The films were deposited by reactive pulsed magnetron sputtering using the Double Ring Magnetron DRM 400. This sputter source together with suitable powering and process control allows depositing piezoelectric AlN very homogeneously on 8" substrates with deposition rates of up to 200 nm/min. With the developed technology, film thicknesses of several ten microns are technically and economically feasible. Moreover, by adjusting process parameters accordingly, it is possible to tune properties, like film stress, to application specific requirements. Additionally, it is known that the doping of AlN with Scandium results in a significantly increased piezoelectric coefficient. The influence of process parameters and Sc concentration on film properties were determined by piezometer, pulse echo, SEM, XRD, EDS and nanoindentation measurements. Energy harvesting measurements were done using an electromechanical shaker system for the excitation of defined vibrations and a laservibrometer for determination of the displacement of the samples. The generated power was measured as function of electric load at resonance. An rms power of up to 140μW using AlN films and of 350μW using AlScN films was generated on Si test pieces of 8x80mm2. Furthermore, energy harvesting measurements using manually bended steel strips of 75x25mm2 coated with AlScN were carried out as well. When using only a single actuation, energy of up to 8μJ could be measured. By letting the system vibrate freely, the damped vibration at resonance 50Hz resulted in a measured energy of 420μJ.

  6. Enthalpy restoration in geothermal energy processing system

    Science.gov (United States)

    Matthews, Hugh B.

    1983-01-01

    A geothermal deep well energy extraction system is provided of the general type in which solute-bearing hot water is pumped to the earth's surface from a relatively low temperature geothermal source by transferring thermal energy from the hot water to a working fluid for driving a primary turbine-motor and a primary electrical generator at the earth's surface. The superheated expanded exhaust from the primary turbine motor is conducted to a bubble tank where it bubbles through a layer of sub-cooled working fluid that has been condensed. The superheat and latent heat from the expanded exhaust of the turbine transfers thermal energy to the sub-cooled condensate. The desuperheated exhaust is then conducted to the condenser where it is condensed and sub-cooled, whereupon it is conducted back to the bubble tank via a barometric storage tank. The novel condensing process of this invention makes it possible to exploit geothermal sources which might otherwise be non-exploitable.

  7. Process sedimentology of submarine fan deposits - new perspectives

    Science.gov (United States)

    Postma, George

    2017-04-01

    To link submarine fan process sedimentology with sand distribution, sand body architecture, texture and fabric, the field geologist studies sedimentary facies, facies associations (fan elements) and stratigraphy. Facies analysis resides on factual knowledge of modern fan morphodynamics and physical modelling of en-masse sediment transport. Where do we stand after 55 years of submarine research, i.e. the date when the first submarine fan model was launched by Arnold Bouma in 1962? Since that date students of submarine fans have worked on a number of important, recurring questions concerned with facies analysis of submarine successions in outcrop and core: 1. What type of sediment transport produced the beds? 2. What facies can be related to initial flow conditions? 3. What is the significance of grain size jumps and bounding surface hierarchy in beds consisting of crude and spaced stratification (traction carpets)? Do these point to multi flow events or to flow pulsations by one and the same event? 4. What facies associations relate to the basic elements of submarine fans? 5. What are the autogenic and allogenic signatures in submarine fans? Particularly in the last decade, the enormous technical advancement helped to obtain high-quality data from observations of density flows in modern canyons, deep basins and deep-water delta slopes (refs 1,2,3). In combination with both physical (refs 4,5) and numerical modelling (ref 6) these studies broke new ground into our understanding of density flow processes in various submarine environments and have led to new concepts of submarine fan building by super- and subcritical high-density flow (ref 7). Do these new concepts provide better answers to our recurrent questions related to the morphodynamics of submarine fans and prediction of sand body architecture? In discussing this open question, I shall 1. apply the new concepts to a modern and ancient example of a channel-lobe-transition-zone (ref 8); 2. raise the problem of

  8. Modelling and optimization of film thickness variation for plasma enhanced chemical vapour deposition processes

    Science.gov (United States)

    Waddell, Ewan; Gibson, Des; Lin, Li; Fu, Xiuhua

    2011-09-01

    This paper describes a method for modelling film thickness variation across the deposition area within plasma enhanced chemical vapour deposition (PECVD) processes. The model enables identification and optimization of film thickness uniformity sensitivities to electrode configuration, temperature, deposition system design and gas flow distribution. PECVD deposition utilizes a co-planar 300mm diameter electrodes with separate RF power matching to each electrode. The system has capability to adjust electrode separation and electrode temperature as parameters to optimize uniformity. Vacuum is achieved using dry pumping with real time control of butterfly valve position for active pressure control. Comparison between theory and experiment is provided for PECVD of diamond-like-carbon (DLC) deposition onto flat and curved substrate geometries. The process utilizes butane reactive feedstock with an argon carrier gas. Radiofrequency plasma is used. Deposited film thickness sensitivities to electrode geometry, plasma power density, pressure and gas flow distribution are demonstrated. Use of modelling to optimise film thickness uniformity is demonstrated. Results show DLC uniformity of 0.30% over a 200 mm flat zone diameter within overall electrode diameter of 300mm. Thickness uniformity of 0.75% is demonstrated over a 200mm diameter for a non-conformal substrate geometry. Use of the modelling method for PECVD using metal-organic chemical vapour deposition (MOCVD) feedstock is demonstrated, specifically for deposition of silica films using metal-organic tetraethoxy-silane. Excellent agreement between experimental and theory is demonstrated for conformal and non-conformal geometries. The model is used to explore scalability of PECVD processes and trade-off against film thickness uniformity. Application to MEMS, optical coatings and thin film photovoltaics is discussed.

  9. Genetic Algorithm-based Optimization to Match Asteroid Energy Deposition Curves

    Science.gov (United States)

    Tarano, Ana Maria; Mathias, Donovan; Wheeler, Lorien; Close, Sigrid

    2017-10-01

    An asteroid entering Earth’s atmosphere deposits energy along its path due to thermal ablation and dissipative forces that can be measured by ground-based and space-borne instruments. Inference of pre-entry asteroid properties and characterization of the atmospheric breakup is facilitated by using an analytic fragment-cloud model (FCM) in conjunction with a Genetic Algorithm (GA). This optimization technique is used to inversely solve for the asteroid’s entry properties, such as diameter, density, strength, velocity, entry angle, ablation coefficient, and strength scaling, from simulations using FCM. The previous parameters’ fitness evaluation involves minimizing residuals and comparing the incremental energy deposited to ascertain the best match between the physics-based calculated energy deposition and the observed meteors. This steady-state GA provided sets of solutions agreeing with literature, such as the meteor from Chelyabinsk, Russia in 2013 and Tagish Lake, Canada in 2000, which were used as case studies in order to validate the optimization routine. The assisted exploration and exploitation of this multi-dimensional search space enables inference and uncertainty analysis that can inform studies of near-Earth asteroids and consequently improve risk assessment.

  10. Simulation of diesel engine energy conversion processes

    Directory of Open Access Journals (Sweden)

    А. С. Афанасьев

    2016-12-01

    Full Text Available In order to keep diesel engines in good working order the troubleshooting methods shall be improved. For their further improvement by parameters of associated processes a need has arisen to develop a diesel engine troubleshooting method based on time parameters of operating cycle. For such method to be developed a computational experiment involving simulation of diesel engine energy conversion processes has been carried out. The simulation was based on the basic mathematical model of reciprocating internal combustion engines, representing a closed system of equations and relationships. The said model has been supplemented with the engine torque dynamics taking into account the current values of in-cylinder processes with different amounts of fuel injected, including zero feed.The torque values obtained by the in-cylinder pressure conversion does not account for mechanical losses, which is why the base simulation program has been supplemented with calculations for the friction and pumping forces. In order to determine the indicator diagram of idle cylinder a transition to zero fuel feed mode and exclusion of the combustion process from calculation have been provisioned.

  11. Monte Carlo calculations of energy deposition distributions of electrons below 20 keV in protein.

    Science.gov (United States)

    Tan, Zhenyu; Liu, Wei

    2014-05-01

    The distributions of energy depositions of electrons in semi-infinite bulk protein and the radial dose distributions of point-isotropic mono-energetic electron sources [i.e., the so-called dose point kernel (DPK)] in protein have been systematically calculated in the energy range below 20 keV, based on Monte Carlo methods. The ranges of electrons have been evaluated by extrapolating two calculated distributions, respectively, and the evaluated ranges of electrons are compared with the electron mean path length in protein which has been calculated by using electron inelastic cross sections described in this work in the continuous-slowing-down approximation. It has been found that for a given energy, the electron mean path length is smaller than the electron range evaluated from DPK, but it is large compared to the electron range obtained from the energy deposition distributions of electrons in semi-infinite bulk protein. The energy dependences of the extrapolated electron ranges based on the two investigated distributions are given, respectively, in a power-law form. In addition, the DPK in protein has also been compared with that in liquid water. An evident difference between the two DPKs is observed. The calculations presented in this work may be useful in studies of radiation effects on proteins.

  12. Sustainability, overall and process efficiency of energy crops

    OpenAIRE

    Schäfer, Winfried

    2008-01-01

    A method to calculate efficiency of energy crop production including sun energy, direct and indirect energy for cultivation, processing, and conversion into fuel is demonstrated using rape and derived fuels as an example. Every production and conversion step is a process and calculated separately. The overall efficiency includes energy input and output of all processes. The process efficiency of rape cultivation reaches in Finland up to 1100 %. However, the overall energy effic...

  13. Integration of Electrodeposited Ni-Fe in MEMS with Low-Temperature Deposition and Etch Processes.

    Science.gov (United States)

    Schiavone, Giuseppe; Murray, Jeremy; Perry, Richard; Mount, Andrew R; Desmulliez, Marc P Y; Walton, Anthony J

    2017-03-22

    This article presents a set of low-temperature deposition and etching processes for the integration of electrochemically deposited Ni-Fe alloys in complex magnetic microelectromechanical systems, as Ni-Fe is known to suffer from detrimental stress development when subjected to excessive thermal loads. A selective etch process is reported which enables the copper seed layer used for electrodeposition to be removed while preserving the integrity of Ni-Fe. In addition, a low temperature deposition and surface micromachining process is presented in which silicon dioxide and silicon nitride are used, respectively, as sacrificial material and structural dielectric. The sacrificial layer can be patterned and removed by wet buffered oxide etch or vapour HF etching. The reported methods limit the thermal budget and minimise the stress development in Ni-Fe. This combination of techniques represents an advance towards the reliable integration of Ni-Fe components in complex surface micromachined magnetic MEMS.

  14. Study of the deposition process of vinpocetine on the surface of porous silicon

    Directory of Open Access Journals (Sweden)

    A.S. Lenshin

    Full Text Available Currently the most prospective way in pharmacotherapy is the obtaining of nanoparticles involving pharmaceutical substances. Application of porous inorganic materials on the basis of silicon is among the main features in solving of this problem. The present work is concerned with the problem of the deposition of pharmaceutical drug with nootropic activity – vinpocetine – into porous silicon. Silicon nanoparticles were obtained by electrochemical anodic etching of Si plates. The process of vinpocetine deposition was studied in dependence of the deposition time. As a result of the investigations it was found that infrared transmission spectra of porous silicon with the deposited vinpocetine revealed the absorption bands characteristic of vinpocetine substance. Keywords: Nanoparticles, Porous silicon, Vinpocetine

  15. Electrophoretic Deposition as a New Bioactive Glass Coating Process for Orthodontic Stainless Steel

    Directory of Open Access Journals (Sweden)

    Kyotaro Kawaguchi

    2017-11-01

    Full Text Available This study investigated the surface modification of orthodontic stainless steel using electrophoretic deposition (EPD of bioactive glass (BG. The BG coatings were characterized by spectrophotometry, scanning electron microscopy with energy dispersive X-ray spectrometry, and X-ray diffraction. The frictional properties were investigated using a progressive load scratch test. The remineralization ability of the etched dental enamel was studied according to the time-dependent mechanical properties of the enamel using a nano-indentation test. The EPD process using alternating current produced higher values in both reflectance and lightness. Additionally, the BG coating was thinner than that prepared using direct current, and was completely amorphous. All of the BG coatings displayed good interfacial adhesion, and Si and O were the major components. Most BG-coated specimens produced slightly higher frictional forces compared with non-coated specimens. The hardness and elastic modulus of etched enamel specimens immersed with most BG-coated specimens recovered significantly with increasing immersion time compared with the non-coated specimen, and significant acid-neutralization was observed for the BG-coated specimens. The surface modification technique using EPD and BG coating on orthodontic stainless steel may assist the development of new non-cytotoxic orthodontic metallic appliances having satisfactory appearance and remineralization ability.

  16. Volcanogenic Uranium Deposits: Geology, Geochemical Processes, and Criteria for Resource Assessment

    Science.gov (United States)

    Nash, J. Thomas

    2010-01-01

    Felsic volcanic rocks have long been considered a primary source of uranium for many kinds of uranium deposits, but volcanogenic uranium deposits themselves have generally not been important resources. Until the past few years, resource summaries for the United States or the world generally include volcanogenic in the broad category of 'other deposits' because they comprised less than 0.5 percent of past production or estimated resources. Exploration in the United States from the 1940s through 1982 discovered hundreds of prospects in volcanic rocks, of which fewer than 20 had some recorded production. Intensive exploration in the late 1970s found some large deposits, but low grades (less than about 0.10 percent U3O8) discouraged economic development. A few deposits in the world, drilled in the 1980s and 1990s, are now known to contain large resources (>20,000 tonnes U3O8). However, research on ore-forming processes and exploration for volcanogenic deposits has lagged behind other kinds of uranium deposits and has not utilized advances in understanding of geology, geochemistry, and paleohydrology of ore deposits in general and epithermal deposits in particular. This review outlines new ways to explore and assess for volcanogenic deposits, using new concepts of convection, fluid mixing, and high heat flow to mobilize uranium from volcanic source rocks and form deposits that are postulated to be large. Much can also be learned from studies of epithermal metal deposits, such as the important roles of extensional tectonics, bimodal volcanism, and fracture-flow systems related to resurgent calderas. Regional resource assessment is helped by genetic concepts, but hampered by limited information on frontier areas and undiscovered districts. Diagnostic data used to define ore deposit genesis, such as stable isotopic data, are rarely available for frontier areas. A volcanic environment classification, with three classes (proximal, distal, and pre-volcanic structures

  17. Selective deposition for ''chamber clean-free'' processes using tailored voltage waveform plasmas

    Science.gov (United States)

    Wang, Junkang; v. Johnson, Erik

    2016-09-01

    Tailored Voltage Waveforms (TVWs) have been proven capable of creating plasma asymmetries in otherwise symmetric CCP reactors. Particularly, sawtooth TVWs (described as having strong slope-asymmetry due to different voltage rise/fall slope) can lead to different sheath dynamics, thus generating strongly asymmetric ionization near each electrode. To date, research concerning the slope-asymmetry has only focused on single-gas plasmas. Herein, we present a study looking at SiF4/H2/Ar mixtures to investigate silicon thin film deposition. The resulting surface process depends strongly on multiple precursors, and the deposition requires a specific balance between surface arrival rates of SiFx and H. For a certain gas flow ratio, we can obtain a deposition rate of 0.82Å/s on one electrode and an etching rate of 1.2Å/s on the other. Moreover, the deposition/etching balance can be controlled by H2 flow and waveform amplitude. This is uniquely possible due to the mixed-gas nature of the process and localized ionization generated by sawtooth TVWs. This encourages the prospect that one could choose process conditions to achieve a variety of desired depositions on one electrode, while leaving the other pristine.

  18. Modeling Transport and Processing of Light Absorbing Aerosols Deposited on the Greenland Ice Sheet in 2013

    Science.gov (United States)

    Polashenski, C.; Thomas, J. L.; Soja, A. J.; Dibb, J. E.; Choi, H. D.; Flanner, M.; Bergin, M.; Casey, K.; Chen, J.; Courville, Z.; Raut, J. C.; Shafer, M. M.; Ward, J. L.; Wiedinmyer, C.

    2016-12-01

    The processes that result in aerosol deposition within the Arctic are important for understanding how mid-latitude pollution impacts and modifies the natural Arctic environment. Aerosol deposition is a dominant source of light-absorbing impurities, including black carbon, found in Arctic ice and snow. Trace amounts of light absorbing impurities in snow are important because they are used to interpret past pollution trends (e.g. fire frequency) using ice cores and because they have important climate impacts (warming) due to their modification of snow and ice albedo. Here, we focus on the role of biomass burning in controlling the amount of black carbon deposited on the Greenland ice sheet. Biomass burning is known to modify the Arctic aerosol burden, but large uncertainties remain with respect to the specific processes and impacts. In this presentation, a specific case of light absorbing aerosol deposition to the Greenland ice sheet is studied by combining extensive snow pit measurements with simulations using the regional model WRF-Chem. Light absorbing impurities were measured in snow pits (in 2014) and snow accumulation rates (2013-2014) were monitored at several remote sites on the Greenland ice sheet as part of the SAGE project. The largest black carbon deposition quantity measured was traced to a snow accumulation event that occurred in early August 2013, which included snow deposition having 2-4 cm water equivalent with BC concentrations of up to 40ng/g . In order to understand the origin and identify the processes controlling the observed deposition event, the regional model WRF-Chem is used (run from 17 July - 5 August 2013). The model simulation includes anthropogenic and fire emissions in North America as well as transport and chemical/physical transport processes for both trace gases and aerosols. Model results show that the observed deposition event can be traced to fires burning in northern Canada in late July 2013. The processes controlling aerosol

  19. Energy deposition around swift proton tracks in polymethylmethacrylate: How much and how far

    Science.gov (United States)

    Dapor, Maurizio; Abril, Isabel; de Vera, Pablo; Garcia-Molina, Rafael

    2017-08-01

    The use of proton beams in several modern technologies to probe or modify the properties of materials, such as proton beam lithography or ion beam cancer therapy, requires us to accurately know the extent to which the energy lost by the swift projectiles in the medium is redistributed radially around their tracks, since this determines several endpoints, such as the resolution of imaging or manufacturing techniques, or even the biological outcomes of radiotherapy. In this paper, the radial distribution of the energy deposited around swift-proton tracks in polymethylmethacrylate (PMMA) by the transport of secondary electrons is obtained by means of a detailed Monte Carlo simulation. The initial energy and angular distributions of the secondary electrons generated by proton impact, as well as the electronic cross sections for the ejection of these electrons, are reliably calculated in the framework of the dielectric formalism, where a realistic electronic excitation spectrum of PMMA is accounted for. The cascade of all secondary electrons generated in PMMA is simulated taking into account the main interactions that occur between these electrons and the condensed phase target. After analyzing the influence that several angular distributions of the electrons generated by the proton beam have on the resulting radial profiles of deposited energy, we conclude that the widely used Rudd and Kim formula should be replaced by the simpler isotropic angular distribution, which leads to radial energy distributions comparable to the ones obtained from more realistic angular distributions. By studying the dependence of the radial dose on the proton energy we recommend lower proton energies than previously published for reducing proximity effects around a proton track. The obtained results are of relevance for assessing the resolution limits of proton beam based imaging and manufacturing techniques.

  20. Decay Time Measurement for Different Energy Depositions of Plastic Scintillator Fabricated by High Temperature Polymerization Reaction

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Cheol Ho; Son, Jaebum; Lee, Sangmin; Kim, Tae Hoon; Kim, Yong-Kyun [Hanyang University, Seoul (Korea, Republic of)

    2016-10-15

    Plastic scintillators are based on organic fluorite. They have many advantages such as fast rise and decay time, high optical transmission, ease of manufacturing, low cost, and large available size. For these reasons they are widely used for particle identification. Also, protection of people against a variety of threats (such as nuclear, radiological, and explosive) represents a true challenge along with the continuing development of science and technology. The plastic scintillator is widely used in various devise, which serves for nuclear, photonics, quantum, and high-energy physics. The plastic scintillator is probably the most widely used organic detector, and polystyrene is one of the most widely used materials in the making of the plastic scintillator detector. Thus, a styrene monomer as a solvent was used to fabricate the plastic scintillator by using high temperature polymerization reaction, and then the emission wavelength and the decay times for different energy depositions were measured by using the fabricated plastic scintillator. A plastic scintillator was fabricated to measure decay time for different energy depositions using the high temperature polymerization. Emission wavelength was measured of 426.05 nm to confirm a scintillator property using the spectrophotometer. Four gamma-ray sources (Cs-137, Co-60, Na-22, and Ba-133) were used to evaluate effect for decay time of different energy depositions. The average decay time of the fabricated plastic scintillator was measured to approximately 4.72 ns slightly higher more than commercial plastic scintillator. In future, light output and linearity will be measured to evaluate other property compared with the commercial scintillator.

  1. The erosion performance of cold spray deposited metal matrix composite coatings with subsequent friction stir processing

    Energy Technology Data Exchange (ETDEWEB)

    Peat, Tom, E-mail: tompeat12@gmail.com [Department of Mechanical & Aerospace Engineering, University of Strathclyde, James Weir Building, 75 Montrose Street, Glasgow G1 1XJ (United Kingdom); Galloway, Alexander; Toumpis, Athanasios [Department of Mechanical & Aerospace Engineering, University of Strathclyde, James Weir Building, 75 Montrose Street, Glasgow G1 1XJ (United Kingdom); McNutt, Philip [TWI Ltd., Granta Park, Cambridge CB21 6AL (United Kingdom); Iqbal, Naveed [TWI Technology Centre, Wallis Way, Catcliff, Rotherham, S60 5TZ (United Kingdom)

    2017-02-28

    Highlights: • WC-CoCr, Cr{sub 3}C{sub 2}-NiCr and Al{sub 2}O{sub 3} coatings were cold spray deposited on AA5083 and friction stir processed. • The SprayStirred WC-CoCr demonstrated a hardness increase of 100% over the cold sprayed coating. • As-deposited and SprayStirred coatings were examined under slurry erosion test conditions. • Mass and volume loss was measured following 20-min exposure to the slurry. • The WC-CoCr and Al2O3 demonstrated a reduction in volume loss of approx. 40% over the cold sprayed coating. - Abstract: This study forms an initial investigation into the development of SprayStir, an innovative processing technique for generating erosion resistant surface layers on a chosen substrate material. Tungsten carbide – cobalt chromium, chromium carbide – nickel chromium and aluminium oxide coatings were successfully cold spray deposited on AA5083 grade aluminium. In order to improve the deposition efficiency of the cold spray process, coatings were co-deposited with powdered AA5083 using a twin powder feed system that resulted in thick (>300 μm) composite coatings. The deposited coatings were subsequently friction stir processed to embed the particles in the substrate in order to generate a metal matrix composite (MMC) surface layer. The primary aim of this investigation was to examine the erosion performance of the SprayStirred surfaces and demonstrate the benefits of this novel process as a surface engineering technique. Volumetric analysis of the SprayStirred surfaces highlighted a drop of approx. 40% in the level of material loss when compared with the cold spray deposited coating prior to friction stir processing. Micro-hardness testing revealed that in the case of WC-CoCr reinforced coating, the hardness of the SprayStirred material exhibits an increase of approx. 540% over the unaltered substrate and 120% over the as-deposited composite coating. Microstructural examination demonstrated that the increase in the hardness of the

  2. A hybrid model of laser energy deposition for multi-dimensional simulations of plasmas and metals

    Science.gov (United States)

    Basko, Mikhail M.; Tsygvintsev, Ilia P.

    2017-05-01

    The hybrid model of laser energy deposition is a combination of the geometrical-optics ray-tracing method with the one-dimensional (1D) solution of the Helmholtz wave equation in regions where the geometrical optics becomes inapplicable. We propose an improved version of this model, where a new physically consistent criterion for transition to the 1D wave optics is derived, and a special rescaling procedure of the wave-optics deposition profile is introduced. The model is intended for applications in large-scale two- and three-dimensional hydrodynamic codes. Comparison with exact 1D solutions demonstrates that it can fairly accurately reproduce the absorption fraction in both the s- and p-polarizations on arbitrarily steep density gradients, provided that a sufficiently accurate algorithm for gradient evaluation is used. The accuracy of the model becomes questionable for long laser pulses simulated on too fine grids, where the hydrodynamic self-focusing instability strongly manifests itself.

  3. Composite manufacturing process for wind energy turbines

    Energy Technology Data Exchange (ETDEWEB)

    Rekret, A. [Mastercore System Ltd., Mississauga, ON (Canada)

    2008-07-01

    This paper described a unibody design for vertical axis wind turbines developed by the Mastercore Group of companies (Mastercore). The company's thermoplastic composites are among the strongest, lightest, and highest efficiency wind or water blades available in the market. The unibody design requires neither an external frame, nor an internal strut. This paper described the aerodynamic principle loads; lade shape and turbine design; and the manufacturing system. Mastercore's engineered product addresses the problem of turbulence that is caused by a smooth blade. A smooth blade causes noise, instability and can result in a loss of energy. Mastercore produces a broad range of accurately controllable impregnation levels, saving on the cost of resin and providing uniform mechanical properties. Their processes focus on the efficient impregnation of tows to manufacture in-line fabrics, tapes and other substrates based on carbon, glass, aramid or any other type of reinforcements. The process is environmentally sound, eliminates the emission of volatile organic compounds (VOCs), reduces wastes and meets stringent regulations. 7 figs.

  4. Polychlorinated biphenyls in glaciers. 2. Model results of deposition and incorporation processes.

    Science.gov (United States)

    Steinlin, Christine; Bogdal, Christian; Scheringer, Martin; Pavlova, Pavlina A; Schwikowski, Margit; Schmid, Peter; Hungerbühler, Konrad

    2014-07-15

    In previous work, Alpine glaciers have been identified as a secondary source of persistent organic pollutants (POPs). However, detailed understanding of the processes organic chemicals undergo in a glacial system was missing. Here, we present results from a chemical fate model describing deposition and incorporation of polychlorinated biphenyls (PCBs) into an Alpine glacier (Fiescherhorn, Switzerland) and an Arctic glacier (Lomonosovfonna, Norway). To understand PCB fate and dynamics, we investigate the interaction of deposition, sorption to ice and particles in the atmosphere and within the glacier, revolatilization, diffusion and degradation, and discuss the effects of these processes on the fate of individual PCB congeners. The model is able to reproduce measured absolute concentrations in the two glaciers for most PCB congeners. While the model generally predicts concentration profiles peaking in the 1970s, in the measurements, this behavior can only be seen for higher-chlorinated PCB congeners on Fiescherhorn glacier. We suspect seasonal melt processes are disturbing the concentration profiles of the lower-chlorinated PCB congeners. While a lower-chlorinated PCB congener is mainly deposited by dry deposition and almost completely revolatilized after deposition, a higher-chlorinated PCB congener is predominantly transferred to the glacier surface by wet deposition and then is incorporated into the glacier ice. The incorporated amounts of PCBs are higher on the Alpine glacier than on the Arctic glacier due to the higher precipitation rate and aerosol particle concentration on the former. Future studies should include the effects of seasonal melt processes, calculate the quantities of PCBs incorporated into the entire glacier surface, and estimate the quantity of chemicals released from glaciers to determine the importance of glaciers as a secondary source of organic chemicals to remote aquatic ecosystems.

  5. Transmission of electrons through insulating PET foils: Dependence on charge deposition, tilt angle and incident energy

    Energy Technology Data Exchange (ETDEWEB)

    Keerthisinghe, D., E-mail: darshika.keerthisinghe@wmich.edu [Department of Physics, Western Michigan University, Kalamazoo, MI 49008 (United States); Dassanayake, B.S. [Department of Physics, University of Peradeniya, Peradeniya (Sri Lanka); Wickramarachchi, S.J. [Department of Physics, Western Michigan University, Kalamazoo, MI 49008 (United States); Stolterfoht, N. [Helmholtz-Zentrum Berlin für Materialien und Energie, D-14109 Berlin (Germany); Tanis, J.A. [Department of Physics, Western Michigan University, Kalamazoo, MI 49008 (United States)

    2016-09-01

    Transmission of electrons through insulating polyethylene terephthalate (PET) nanocapillaries was observed as a function of charge deposition, angular and energy dependence. Two samples with capillary diameters 100 and 200 nm and pore densities 5 × 10{sup 8}/cm{sup 2} and 5 × 10{sup 7}/cm{sup 2}, respectively, were studied for incident electron energies of 300, 500 and 800 eV. Transmission and steady state of the electrons were attained after a time delay during which only a few electron counts were observed. The transmission through the capillaries depended on the tilt angle with both elastic and inelastic electrons going through. The guiding ability of electrons was found to increase with the incident energy in contrast to previous measurements in our laboratory for a similar PET foil.

  6. Microwave plasma assisted process for cleaning and deposition in future semiconductor technology

    Science.gov (United States)

    Altmannshofer, S.; Boudaden, J.; Wieland, R.; Eisele, I.; Kutter, C.

    2017-06-01

    The epitaxial growth of silicon layers is an important step in the fabrication of semiconductor devices. For conventional silicon epitaxy, high temperatures, up to 900 °C are necessary. However, in future, semiconductor technology epitaxy processes at lower temperatures are required to increase the integration density. The goal of this study was to investigate microwave plasma assisted processes for the selective removing of thin silicon oxide, the cleaning of silicon surfaces and the depositing of high quality silicon films. The main focus was to apply these processes for low temperature epitaxy. All processes, such as oxide removal, cleaning and deposition, were done in one chamber and with microwave plasma assistance. In order to remove silicon dioxide, the etching behavior of hydrogen, fluorine, and hydrogen/fluorine plasma was studied. It was shown, that with hydrogen/fluorine plasma, the best selectivity of oxide to silicon was reached. The deposition process of silicon was studied by growing μc-Si films. The process was characterized and optimized by spectral ellipsometry. After a successful characterization of all process steps, silicon epitaxy layers have been grown with in-situ removal of native oxide and in-situ surface cleaning. The temperature for all process steps was reduced below 450 °C.

  7. Solution processed deposition of electron transport layers on perovskite crystal surface—A modeling based study

    Energy Technology Data Exchange (ETDEWEB)

    Mortuza, S.M.; Taufique, M.F.N.; Banerjee, Soumik, E-mail: soumik.banerjee@wsu.edu

    2017-02-01

    Highlights: • The model determined the surface coverage of solution-processed film on perovskite. • Calculated surface density map provides insight into morphology of the monolayer. • Carbonyl oxygen atom of PCBM strongly attaches to the (110) surface of perovskite. • Uniform distribution of clusters on perovskite surface at lower PCBM concentration. • Deposition rate of PCBM on the surface is very high at initial stage of film growth. - Abstract: The power conversion efficiency (PCE) of planar perovskite solar cells (PSCs) has reached up to ∼20%. However, structural and chemicals defects that lead to hysteresis in the perovskite based thin film pose challenges. Recent work has shown that thin films of [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) deposited on the photo absorption layer, using solution processing techniques, minimize surface pin holes and defects thereby increasing the PCE. We developed and employed a multiscale model based on molecular dynamics (MD) and kinetic Monte Carlo (kMC) to establish a relationship between deposition rate and surface coverage on perovskite surface. The MD simulations of PCBMs dispersed in chlorobenzene, sandwiched between (110) perovskite substrates, indicate that PCBMs are deposited through anchoring of the oxygen atom of carbonyl group to the exposed lead (Pb) atom of (110) perovskite surface. Based on rates of distinct deposition events calculated from MD, kMC simulations were run to determine surface coverage at much larger time and length scales than accessible by MD alone. Based on the model, a generic relationship is established between deposition rate of PCBMs and surface coverage on perovskite crystal. The study also provides detailed insights into the morphology of the deposited film.

  8. Ti film deposition process of a plasma focus: Study by an experimental design

    Directory of Open Access Journals (Sweden)

    M. J. Inestrosa-Izurieta

    2017-10-01

    Full Text Available The plasma generated by plasma focus (PF devices have substantially different physical characteristics from another plasma, energetic ions and electrons, compared with conventional plasma devices used for plasma nanofabrication, offering new and unique opportunities in the processing and synthesis of Nanomaterials. This article presents the use of a plasma focus of tens of joules, PF-50J, for the deposition of materials sprayed from the anode by the plasma dynamics in the axial direction. This work focuses on the determination of the most significant effects of the technological parameters of the system on the obtained depositions through the use of a statistical experimental design. The results allow us to give a qualitative understanding of the Ti film deposition process in our PF device depending on four different events provoked by the plasma dynamics: i an electric erosion of the outer material of the anode; ii substrate ablation generating an interlayer; iii electron beam deposition of material from the center of the anode; iv heat load provoking clustering or even melting of the deposition surface.

  9. Functional nickel-based deposits synthesized by focused beam induced processing

    Science.gov (United States)

    Córdoba, R.; Barcones, B.; Roelfsema, E.; Verheijen, M. A.; Mulders, J. J. L.; Trompenaars, P. H. F.; Koopmans, B.

    2016-02-01

    Functional nanostructures fabricated by focused electron/ion beam induced processing (FEBIP/FIBIP) open a promising route for applications in nanoelectronics. Such developments rely on the exploration of new advanced materials. We report here the successful fabrication of nickel-based deposits by FEBIP/FIBIP using bis(methyl cyclopentadienyl)nickel as a precursor. In particular, binary compounds such as nickel oxide (NiO) are synthesized by using an in situ two-step process at room temperature. By this method, as-grown Ni deposits transform into homogeneous NiO deposits using focused electron beam irradiation under O2 flux. This procedure is effective in producing highly pure NiO deposits with resistivity of 2000 Ωcm and a polycrystalline structure with face-centred cubic lattice and grains of 5 nm. We demonstrate that systems based on NiO deposits displaying resistance switching and an exchange-bias effect could be grown by FEBIP using optimized parameters. Our results provide a breakthrough towards using these techniques for the fabrication of functional nanodevices.

  10. Influence of Oxygen Partial Pressure during Processing on the Thermoelectric Properties of Aerosol-Deposited CuFeO2

    Science.gov (United States)

    Stöcker, Thomas; Exner, Jörg; Schubert, Michael; Streibl, Maximilian; Moos, Ralf

    2016-01-01

    In the field of thermoelectric energy conversion, oxide materials show promising potential due to their good stability in oxidizing environments. Hence, the influence of oxygen partial pressure during synthesis on the thermoelectric properties of Cu-Delafossites at high temperatures was investigated in this study. For these purposes, CuFeO2 powders were synthetized using a conventional mixed-oxide technique. X-ray diffraction (XRD) studies were conducted to determine the crystal structures of the delafossites associated with the oxygen content during the synthesis. Out of these powders, films with a thickness of about 25 µm were prepared by the relatively new aerosol-deposition (AD) coating technique. It is based on a room temperature impact consolidation process (RTIC) to deposit dense solid films of ceramic materials on various substrates without using a high-temperature step during the coating process. On these dense CuFeO2 films deposited on alumina substrates with electrode structures, the Seebeck coefficient and the electrical conductivity were measured as a function of temperature and oxygen partial pressure. We compared the thermoelectric properties of both standard processed and aerosol deposited CuFeO2 up to 900 °C and investigated the influence of oxygen partial pressure on the electrical conductivity, on the Seebeck coefficient and on the high temperature stability of CuFeO2. These studies may not only help to improve the thermoelectric material in the high-temperature case, but may also serve as an initial basis to establish a defect chemical model. PMID:28773351

  11. Unconfined alluvial flow processes: Recognition and interpretation of their deposits, and the significance for palaeogeographic reconstruction

    Science.gov (United States)

    North, Colin P.; Davidson, Stephanie K.

    2012-02-01

    Palaeogeographic interpretation of the sedimentary rock record depends on correct recognition from the preserved evidence of the processes responsible for transporting and depositing the sediment. This in turn depends on robust knowledge transfer from previous workers, and the successful exchange of ideas between workers requires consistent use of a well-defined vocabulary. We have identified serious breakdowns in all these interpretation steps in the case of terrestrial unconfined flow and its deposits, and these failures are leading to unreliable environmental and climatic interpretation. This is significant because such alluvial deposits commonly form a majority of the rock record of continental environments. Working from the basic principles of geomorphology and fluid dynamics, we have undertaken a wide-ranging analysis of the nature of out-of-channel flow and from this make predictions about the characteristics of its deposits. We identify the range of possible locations and conditions that lead to the development of unconfined flow, review the processes operating in each case, and examine the range of lithological features that can be produced by these processes. This allows us to evaluate the reliability of the criteria claimed for identification of out-of-channel flow deposits, and examine how our new insights might alter palaeoclimatic and palaeogeographic reconstructions published previously by others. The sedimentary record of unconfined flows is much more diverse and complex than usually portrayed. The received wisdom that the record of unconfined flow consists solely of upwards-fining thin beds produced from shallow waning flows is shown to be flawed. A wide range of lithofacies are possible, and the variation in both flow steadiness and uniformity needs to be taken into account. The previously published criteria for recognition of flows of this type are not diagnostic of process or location; unconfined flow deposits cannot reliably be identified from

  12. Self-catalytic growth of tin oxide nanowires by chemical vapor deposition process

    CSIR Research Space (South Africa)

    Thabethe, BS

    2013-01-01

    Full Text Available The authors report on the synthesis of tin oxide (SnO(sub2)) nanowires by a chemical vapor deposition (CVD) process. Commercially bought SnO nanopowders were vaporized at 1050°C for 30 minutes with argon gas continuously passing through the system...

  13. Optimization of Nano-Process Deposition Parameters Based on Gravitational Search Algorithm

    Directory of Open Access Journals (Sweden)

    Norlina Mohd Sabri

    2016-06-01

    Full Text Available This research is focusing on the radio frequency (RF magnetron sputtering process, a physical vapor deposition technique which is widely used in thin film production. This process requires the optimized combination of deposition parameters in order to obtain the desirable thin film. The conventional method in the optimization of the deposition parameters had been reported to be costly and time consuming due to its trial and error nature. Thus, gravitational search algorithm (GSA technique had been proposed to solve this nano-process parameters optimization problem. In this research, the optimized parameter combination was expected to produce the desirable electrical and optical properties of the thin film. The performance of GSA in this research was compared with that of Particle Swarm Optimization (PSO, Genetic Algorithm (GA, Artificial Immune System (AIS and Ant Colony Optimization (ACO. Based on the overall results, the GSA optimized parameter combination had generated the best electrical and an acceptable optical properties of thin film compared to the others. This computational experiment is expected to overcome the problem of having to conduct repetitive laboratory experiments in obtaining the most optimized parameter combination. Based on this initial experiment, the adaptation of GSA into this problem could offer a more efficient and productive way of depositing quality thin film in the fabrication process.

  14. Alpha-Energy-Deposition-Profiling of Radioisotope p-i-n Diodes for Power Generation

    Science.gov (United States)

    Cress, Cory; Raffaelle, Ryne

    2006-03-01

    The high energy density and long half-life of certain alpha-emitting radioisotopes enables viable and long-lived power supplies to be fabricated on the micro-scale. A design incorporating an InGaP p-i-n photovoltaic (PV) device that directly converts the kinetic energy of the alpha-particles into electricity represents both a scalable and efficient microsystem design. To better understand the relationship between the alpha-energy-deposition-profile (ADEP) and the maximum power conversion efficiency for this device structure, we have performed two systematic studies. In these studies, I-V characteristics for the InGaP PV device under alpha-flux are measured as a function of alpha source distance, and as function of aluminum film thickness (10 nm to 10 μm) which is deposited onto the surface of the PV device. Both techniques will alter the ADEP in relation to the active region of the PV device. These experimental results are compared to a theoretical model which utilizes Monte Carlo simulations and numerical calculations to determine the ADEP for the same device configuration. The understanding gained from this analysis has direct implications towards the fabrication of radioisotope microbatteries with structural characteristics that enable optimal power conversion efficiencies to be achieved.

  15. Molecular dynamics study of structural changes versus deposited energy dose in a sodium borosilicate glass

    Energy Technology Data Exchange (ETDEWEB)

    Bureau, G.; Delaye, J.M.; Peuget, S. [DEN/DTCD/SECM, CEA Marcoule, BP 17171, Bagnols-sur-Ceze cedex, 30207 (France); Calas, G. [IMPMC, 140 rue de Lourmel, Paris, 75015 (France)

    2008-07-01

    Assessing the long-term behavior of nuclear glass implies evaluating the impact of cumulative alpha decay induced by the minor actinides it contains. When subjected to alpha decay ({sup 244}Cm-doped glass specimens) or to external ion irradiation, some macroscopic properties vary appreciably with the dose. Above a given dose level, the properties do not evolve any more. To improve our understanding of these modifications, studies are carried out on simplified glass compositions (three oxides SiO{sub 2}, B{sub 2}O{sub 3}, Na{sub 2}O), modeled by molecular dynamics in which irradiation effects are simulated by accelerating uranium projectiles. Accumulation of displacements cascades have been performed up to 4.5*10{sup 20} keV/cm{sup 3} nuclear energy deposited in the glass. The density variations observed in actinide-doped materials is qualitatively reproduced. At high doses, the swelling tends to stabilize. Marples model is used to fit the glass swelling versus the deposited energy dose, giving the volume damaged per projectile. This volume approximates the cascade core volume, suggesting that the underlying mechanisms of volume expansion are contained in the cascade core and are thus related to the highest energy events: atom ejection and thermal quenching. On the contrary, the volumetric parameter of the Marples model applied to the other structural properties is related to a volume corresponding to the core + periphery of the cascades. (authors)

  16. Slope processes in weathered volcaniclastic deposits within the city of Naples: The Camaldoli Hill case

    Science.gov (United States)

    Calcaterra, D.; Coppin, D.; de Vita, S.; Di Vito, M. A.; Orsi, G.; Palma, B.; Parise, M.

    2007-06-01

    We describe the slope processes acting on Camaldoli Hill, the main volcanic feature of the Neapolitan area whose geological evolution and setting have been reconstructed. The backbone of the hill includes the remnants of two partially superposed tuff cones, lying between the Campanian Ignimbrite (CI) and the Neapolitan Yellow Tuff (NYT). This sequence is mantled by pyroclastic, anthropogenic and epiclastic deposits, with abrupt thickness and facies variations. The structural setting of the hill mainly results from several phases of reactivation of the CI caldera faults which were active until about 9.5 ka. Deformation younger than 15 ka is evidenced by landslide deposits, caused by slope instability from volcano-tectonism, and by a high-angle erosional unconformity, formed in response to a base-level lowering. A stratigraphic analysis of the reworked deposits at the foot of the slopes allowed us to define both depositional mechanisms and sedimentation rates. The results of combined volcanological, geomorphological and engineering-geological studies permitted us to constrain and quantify past geological processes and hypothesis about the future evolution of the hill. Present-day slope processes on Camaldoli Hill are largely controlled by the presence of weathered and reworked deposits, whose nature and thickness have been analysed and mapped in detail. Four main kinds of slope processes have been recognized: falls and toppling failures from NYT; small-scale slides in the weathered and pedogenized loose cover; mixed events, represented by slides evolving to hyperconcentrated flows, mud flows and debris flows; and areal and linear erosion. Consequently, a high number of mass movements not previously documented have been mapped. At the same time, an insight into the sedimentation rate due to the overall slope processes, covering a time-span of about 5 ka, was given. Some final considerations regarding landslide hazard are presented in the context of the most suitable

  17. PIV analysis of the homogeneity of energy deposition during development of a plasma actuator channel

    Science.gov (United States)

    Glazyrin, F. N.; Znamenskaya, I. A.; Mursenkova, I. V.; Naumov, D. S.; Sysoev, N. N.

    2016-01-01

    Nonstationary velocity fields that arise during the development of flows behind shock (blast) waves initiated by pulsed surface sliding discharge in air at a pressure of (2-4) × 104 Pa have been experimentally studied by the particle image velocimetry (PIV) technique. Plasma sheets (nanosecond discharges slipping over a dielectric surface) were initiated on walls of a rectangular chamber. Spatial analysis of the shape of shock-wave fronts and the distribution of flow velocities behind these waves showed that the pulsed energy deposition is homogeneous along discharge channels of a plasma sheet, while the integral visible plasma glow intensity decreases in the direction of channel propagation.

  18. FCC-hh final-focus for flat-beams: parameters and energy deposition studies

    CERN Document Server

    AUTHOR|(CDS)2081283; Cruz Alaniz, Emilia; Seryi, Andrei; Van Riesen-Haupt, Leon; Besana, Maria Ilaria

    2017-01-01

    The international Future Circular Collider (FCC) study comprises the study of a new scientific structure in a tunnel of 100 km. This will allow the installation of two accelerators, a 45.6–175 GeV lepton collider and a 100-TeV hadron collider. An optimized design of a final-focus system for the hadron collider is presented here. The new design is more compact and enables unequal ${\\beta}$$^{∗}$ in both planes, whose choice is justified here. This is followed by energy deposition studies, where the total dose in the magnets as a consequence of the collision debris is evaluated.

  19. Compensation of decreased ion energy by increased hydrogen dilution in plasma deposition of thin film silicon solar cells at low substrate temperatures

    NARCIS (Netherlands)

    Verkerk, A.D.; de Jong, M.M.; Rath, J.K.; Brinza, M.; Schropp, R.E.I.; Goedheer, W.J.; Krzhizhanovskaya, V.V.; Gorbachev, Y.E.; Orlov, K.E.; Khilkevitch, E.M.; Smirnov, A.S.

    2009-01-01

    In order to deposit thin film silicon solar cells on plastics and papers, the deposition process needs to be adapted for low deposition temperatures. In a very high frequency plasma-enhanced chemical vapor deposition (VHF PECVD) process, both the gas phase and the surface processes are affected by

  20. Method of Biomaterials Processing into Energy Carrier

    Energy Technology Data Exchange (ETDEWEB)

    Nikoghosyan, S. [Surentechnology, St. Ancona, AP (Italy)

    2006-07-15

    The progressive method of biomass processing into energy carrier as briquettes (Pellets) is described in the present work. It is based on institution of polymer Naralex into the milled biomass in proportion 100:2. Naralex is a light yellow powder with dispersity from 20 to 200 mkm. The nature (type) of biomass does not effect the quality of final product-briquette. The mixture is activated when reaching the temperature 180 deg C, whereas the humidity of the primary product-biomass should not exceed 20%. The machine is elaborated in accordance with the technology. It has got several design solutions on productivity, is equipped with automatic control of parameters. Operating mode is perpetual - 24 hours. The final product has got advanced physical-mechanical properties: solidity, water-, moisture resistance, heat emission up to 8000 kcal/h, burns without a smoke and smell. The product is ecologically pure, certified according to all parameters provided in standards. The ready briquette is durable, does not get out of order even if kept for a long time in the conditions of high humidity. It has a low cost.

  1. Modeling of atmospheric iron processing carried by mineral dust and its deposition to ocean

    Science.gov (United States)

    Nickovic, Slobodan; Vukovic, Ana; Vujadinovic, Mirjam

    2014-05-01

    Relatively insoluble iron in dust originating from desert soils increases its solubility after Fe carried by mineral dust is chemically processed by the atmosphere. After dust is deposited deposition to the ocean, soluble Fe as a nutrient could enhance the marine primary production. The atmospheric dust cycle is driven by the atmospheric processes often of smaller, meso-scales. The soil mineralogy of dust emitted from sources determines also how much Fe in the aerosol will be finding. Once Fe is exposed to the atmospheric processes, the atmospheric radiation, clouds and polluted air will chemically affect the iron in dust. Global dust-iron models, having typical horizontal resolutions of 100-300 km which are mostly used to numerically simulate the fate of iron in the atmosphere can provide rather global picture of the dust and iron transport, but not details. Such models often introduce simplistic approximation on the Fe content in dust-productive soils. To simulate the Fe processing we instead implemented a high resolution regional atmospheric dust-iron model with detailed 1km global map for the geographic distribution of Fe content in soil. We also introduced a parameterization of the Fe processing caused by dust mineralogy, cloud processes and solar radiation. We will present results from simulation experiments in order to explore the model capability to reproduce major observed patterns of deposited Fe into the Atlantic cruises.

  2. Experimentally Investigating the Effect of Temperature Differences in the Particle Deposition Process on Solar Photovoltaic (PV Modules

    Directory of Open Access Journals (Sweden)

    Yu Jiang

    2016-10-01

    Full Text Available This paper reports an experimental investigation of the dust particle deposition process on solar photovoltaic (PV modules with different surface temperatures by a heating plate to illustrate the effect of the temperature difference (thermophoresis between the module surface and the surrounding air on the dust accumulation process under different operating temperatures. In general, if the temperature of PV modules is increased, the energy conversion efficiency of the modules is decreased. However, in this study, it is firstly found that higher PV module surface temperature differences result in a higher energy output compared with those modules with lower temperature differences because of a reduced accumulation of dust particles. The measured deposition densities of dust particles were found to range from 0.54 g/m2 to 0.85 g/m2 under the range of experimental conditions and the output power ratios were found to increase from 0.861 to 0.965 with the increase in the temperature difference from 0 to 50 °C. The PV module with a higher temperature difference experiences a lower dust density because of the effect of the thermophoresis force arising from the temperature gradient between the module surface and its surrounding air. In addition, dust particles have a significant impact on the short circuit current, as well as the output power. However, the influence of particles on open circuit voltage can be negligible.

  3. Multi-Energy Processing for Novel Coating Technologies

    Science.gov (United States)

    2014-12-18

    on thermal heating , are inefficient energy coupling routes to drive gas reactions. As an intensive, coherent and monochromatic light, lasers are...thermal heating , are inefficient energy coupling routes to drive gas reactions. As an intensive, coherent and monochromatic light, lasers are ideal...concentration were deposited using an ammonia-added oxyacetylene flame assisted by IR-laser vibrational excitations of the NH-wagging mode of NH3

  4. Sequential microcontroller-based control for a chemical vapor deposition process

    Directory of Open Access Journals (Sweden)

    Edgar Serrano Pérez

    2017-12-01

    Full Text Available A cost-effective direct liquid injection system is developed for a chemical vapor deposition process using a microcontroller. The precursor gas phase is controlled by the precise sequential injection of a liquid precursor solution to a vaporizing chamber prior deposition. The electronic control system allows the human–machine interface through a LCD display and a keypad matrix. The core of the electronic system is based on an electro mechanical injector operated in time and frequency as a sequential control system by a popular PIC16F877A chip. The software has been developed in the BASIC language and it can be easily modified through an ICSP programmer for different sequential automatized routines. The injection calibration test has proven the linearity of the injection control system for different operation parameters. The results reported the sequential injection MOCVD deposition of alumina thin film.

  5. Numerical solution of moving boundary problem for deposition process in solid fuel gas generator

    Science.gov (United States)

    Volokhov, V. M.; Dorofeenko, S. O.; Sharov, M. S.; Toktaliev, P. D.

    2016-11-01

    Moving boundary problem in application to process of depositions formation in gas generator are considered. Gas generator, as a part of fuel preparation system of high-speed vehicle, convert solid fuel into multicomponent multiphase mixture, which further burned down in combustion chamber. Mathematical model of two-phase “gas-solid particles” flow, including Navier-Stokes equations for turbulent flow in gas generator and mass, impulse conservations laws for elementary depositions layer are proposed. Verification of proposed mathematical model for depositions mass in gas generator conditions is done. Further possible improvements of proposed model, based on more detail accounting of particle-wall interaction and wall's surface adhesion properties are analyzed.

  6. Pulsed laser deposition of the lysozyme protein: an unexpected “Inverse MAPLE” process

    DEFF Research Database (Denmark)

    Schou, Jørgen; Matei, Andreea; Constantinescu, Catalin

    2012-01-01

    Films of organic materials are commonly deposited by laser assisted methods, such as MAPLE (matrix-assisted pulsed laser evaporation), where a few percent of the film material in the target is protected by a light-absorbing volatile matrix. Another possibility is to irradiate the dry organic...... material directly for film production, as in PLD (pulsed laser deposition), where the film molecules may undergo strong fragmentation. In this presentation we report an alternative surprising mechanism for film deposition of the protein lysozyme in vacuum, when a small amount of residual water drives...... which is used in food processing and is also an important constituent of human secretions such as sweat and saliva. It has a well-defined mass (14307 u) and can easily be detected by mass spectrometric methods such as MALDI (Matrix-assisted laser desorption ionization) in contrast to many other organic...

  7. Effect of Processing Parameters on Performance of Spray-Deposited Organic Thin-Film Transistors

    Directory of Open Access Journals (Sweden)

    Jack W. Owen

    2011-01-01

    Full Text Available The performance of organic thin-film transistors (OTFTs is often strongly dependent on the fabrication procedure. In this study, we fabricate OTFTs of soluble small-molecule organic semiconductors by spray-deposition and explore the effect of processing parameters on film morphology and device mobility. In particular, we report on the effect of the nature of solvent, the pressure of the carrier gas used in deposition, and the spraying distance. We investigate the surface morphology using scanning force microscopy and show that the molecules pack along the π-stacking direction, which is the preferred charge transport direction. Our results demonstrate that we can tune the field-effect mobility of spray-deposited devices two orders of magnitude, from 10−3 cm2/Vs to 10−1 cm2/Vs, by controlling fabrication parameters.

  8. Investigating oceanic tidal energy dissipation on deep time scales using short tidal deposit sequences

    Science.gov (United States)

    Coughenour, C.

    2012-12-01

    One of the enduring problems in physical oceanography has been that of tidal dynamics and the effective tidal torque that serves to slow Earth's axial rotation. In the late 20th century, with the aid of satellite altimetry and other technologies, a suite of reliable estimates was finally placed on the magnitude of this torque and other, related parameters in the current epoch. Tidal drag accounts for a 20 microsecond/year increase in mean day length, a 3.5 terawatt dissipation of energy in the oceans (Kantha et al., 1998), and a lunar retreat rate of 3.82 cm/yr (Dickey et al., 1994). Despite these significant advances, however, the problem of tidal dissipation in the geologic past remains largely unresolved. This is due, in part, to difficulties in numerical modeling of past tidal regimes that stem from uncertainties in ocean basin configurations and lunar distances. Tidal deposits can record, to high resolution, the primary astronomical periodicities responsible for the generation of the tidal currents under which transport and deposition occur. With reliable lunar orbital period data obtained from tidal deposits, the past Earth-Moon distance and length of day can be calculated. This task requires careful spectral analysis and consideration of sedimentological factors that may add noise and/or discontinuities to the signal. For deposits representing less than one year of deposition, the necessary assumptions are that Earth's moment of inertia has not changed significantly over the time interval of interest and that the solar component of tidal dissipation can be well-approximated. With consideration of the total angular momentum of the Earth-Moon couplet, we derive a method to calculate lunar distance and length of day. The efficacy of this method and its assumptions is tested via the multi-year sequence of data obtained from the late Precambrian Elatina Formation of Australia and comparing results obtained from the full suite of data by Williams (2000). We go on

  9. Study of Straggling and Extreme Cases of Energy Deposition in Micron Scale Silicon Volumes using the DEPFET Detector

    CERN Document Server

    AUTHOR|(CDS)2094499; Schwenker, Benjamin

    The Depleted P-channel Field-Effect Transistor detector is a pixel detector type currently under development. In high energy physics, pixel detectors measure space points along the trajectory of charged particles. They determine the spatial position by measuring the charges created as a result of interactions with the passing particle. Thus the detector’s signals can be used to determine the energy deposited by the particle in single pixels of a pixel matrix. The development of a new detector raises the question whether our simulation models can accurately describe the physical processes – like ionisation and scattering – taking place during operation. The thesis aims to validate one of the current Monte-Carlo simulations (based on the Geant4 simulation package) of high energy straggling processes using experimental data of a test beam run of DEPFET modules. This is done by calculating the spatial distribution of the electron/hole pairs created in extreme cases of ionisation and using this distribution ...

  10. Beam-induced energy deposition issues in the Very Large Hadron Collider

    CERN Document Server

    Mokhov, N V; Foster, G W

    2001-01-01

    Energy deposition issues are extremely important in the Very Large Hadron Collider (VLHC) with huge energy stored in its 20 TeV (Stage-1) and 87.5 TeV (Stage-2) beams. The status of the VLHC design on these topics, and possible solutions of the problems are discussed. Protective measures are determined based on the operational and accidental beam loss limits for the prompt radiation dose at the surface, residual radiation dose, ground water activation, accelerator components radiation damage and quench stability. The beam abort and beam collimation systems are designed to protect accelerator from accidental and operational beam losses, IP region quadrupoles from irradiation by the products of beam-beam collisions, and to reduce the accelerator-induced backgrounds in the detectors. (7 refs).

  11. 15 CFR 923.13 - Energy facility planning process.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 3 2010-01-01 2010-01-01 false Energy facility planning process. 923... facility planning process. The management program must contain a planning process for energy facilities... affected public and private parties will be involved in the planning process. ...

  12. Comparison of Energy Deposition in the Auroral Oval and Cap Regions for Cases Where Transpolar Structures Exist

    Science.gov (United States)

    Spann, J. F., Jr.; Germany, G. A.; Parks, G. K.; Brittnacher, M. J.

    1998-01-01

    For several cases where the full auroral zone is imaged and transpolar structures exist, we compare the total energy input to the auroral oval with the total energy input in the polar cap. This comparison is made for cases where auroral intensification near local midnight is and is not observed. Temporal evolution of the energy balance between the energy deposited in the oval and polar cap can be used to understand the mechanism that triggers substorms.

  13. Dependence of optical properties and hardness on carbon content in silicon carbonitride films deposited by plasma ion immersion processing technique

    Energy Technology Data Exchange (ETDEWEB)

    Afanasyev-Charkin, I.V.; Nastasi, M. E-mail: nasty@lanl.gov

    2003-05-01

    Materials with Si-C-N composition are of great interest due to their remarkable properties such as high hardness and oxidation resistance. In this study amorphous silicon nitride and silicon carbonitride films were deposited on glass, fused silica, and carbon substrates by the plasma immersion ion processing technique. Gas pressure during the deposition was kept around 0.13 Pa (1 mTorr) and SiH{sub 4}, N{sub 2}, Ar and C{sub 2}H{sub 2} gas mixtures were used. Film hardness, composition and UV-visible optical absorption were characterized using nanoindentation, ion beam analysis techniques, and UV-visible spectroscopy, respectively. The films exhibit high transparency in the visible and near UV regions. Addition of the carbon to the films causes decrease in the density of the films, as well as decrease in hardness and transparency. These results suggest that in the low energy regime of PIIP the deposition of hard carbon composites with nitrogen and silicon does not take place.

  14. Initial studies of Bremsstrahlung energy deposition in small-bore superconducting undulator structures in linac environments

    Energy Technology Data Exchange (ETDEWEB)

    Cremer, T.; Tatchyn, R. [Stanford Univ., CA (United States)

    1995-12-31

    One of the more promising technologies for developing minimal-length insertion devices for linac-driven, single-pass Free Electron Lasers (FELs) operating in the x-ray range is based on the use of superconducting (SC) materials. In recent FEL simulations, for example, a bifilar helical SC device with a 2 cm period and 1.8 T field was found to require a 30 m saturation length for operation at 1.5{Angstrom} on a 15 GeV linac, more than 40% shorter than an alternative hybrid/permanent magnet (hybrid/PM) undulator. AT the same time, however, SC technology is known to present characteristic difficulties for insertion device design, both in engineering detail and in operation. Perhaps the most critical problem, as observed, e.g., by Madey and co-workers in their initial FEL experiments, was the frequent quenching induced by scattered electrons upstream of their (bifilar) device. Postulating that this quenching was precipitated by directly-scattered or bremsstrahlung-induced particle energy deposited into the SC material or into material contiguous with it, the importance of numerical and experimental characterizations of this phenomenon for linac-based, user-facility SC undulator design becomes evident. In this paper we discuss selected prior experimental results and report on initial EGS4 code studies of scattered and bremsstrahlung induced particle energy deposition into SC structures with geometries comparable to a small-bore bifilar helical undulator.

  15. Studies on high electronic energy deposition in transparent conducting indium tin oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Deshpande, N G [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Gudage, Y G [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Ghosh, A [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India); Vyas, J C [Technical and Prototype Engineering Division, Bhabha Atomic Research Center, Trombay, Mumbai (MS) (India); Singh, F [Inter-University Accelerator Center, Aruna Asaf Ali Marg, Post Box 10502, New Delhi 110067 (India); Tripathi, A [Inter-University Accelerator Center, Aruna Asaf Ali Marg, Post Box 10502, New Delhi 110067 (India); Sharma, Ramphal [Thin Film and Nanotechnology Laboratory, Department of Physics, Dr Babasaheb Ambedkar Marathwada University, Aurangabad-431004 (MS) (India)

    2008-02-07

    We have examined the effect of swift heavy ions using 100 MeV Au{sup 8+} ions on the electrical properties of transparent, conducting indium tin oxide polycrystalline films with resistivity of 0.58 x 10{sup -4} {omega} cm and optical transmission greater than 78% (pristine). We report on the modifications occurring after high electronic energy deposition. With the increase in fluency, x-ray line intensity of the peaks corresponding to the planes (1 1 0), (4 0 0), (4 4 1) increased, while (3 3 1) remained constant. Surface morphological studies showed a pomegranate structure of pristine samples, which was highly disturbed with a high dose of irradiation. For the high dose, there was a formation of small spherical domes uniformly distributed over the entire surface. The transmittance was seen to be decreasing with the increase in ion fluency. At higher doses, the resistivity and photoluminescence intensity was seen to be decreased. In addition, the carrier concentration was seen to be increased, which was in accordance with the decrease in resistivity. The observed modifications after high electronic energy deposition in these films may lead to fruitful device applications.

  16. The use of hollow cathodes in deposition processes: A critical review

    Energy Technology Data Exchange (ETDEWEB)

    Muhl, Stephen, E-mail: muhl@unam.mx; Pérez, Argelia

    2015-03-31

    of electrons (we will call this a hollow cathode arc or HCA). The accepted explanation for the HCD phenomenon involves the existence of high-energy “pendulum” electrons, which are reflected from the sheaths on either side of the cathode; the long trajectory of this electron is understood to produce a large number of secondary electrons, with this resulting in the high plasma density and plasma current. We describe the structure of a parallel-plate discharge, particularly the gas phase and cathode surface excitation and ionization collision processes. Using this description, we discuss some of the problems associated with the conventional hollow cathode model and we propose a new explanation that has important implications for the physics and applications of hollow cathodes. In the last section of this review, we describe how hollow cathodes have and can be used to deposit thin films and nanostructured coatings. We provide an extensive and approximately chronological listing of how hollow cathodes have been successfully used to deposit materials, mainly by sputtering and plasma enhanced chemical vapour deposition based techniques. - Highlights: • We describe the discrepancies of the pendulum model of the hollow cathode plasma. • We present a model of the hollow cathode discharge based on doubly-charged ions. • The secondary electron yield of Ar{sup ++} from the cathode is about 4 times that of Ar{sup +}. • Plasma generation of Ar{sup ++} and the secondary electron emission are quasi-resonant. • A very high density hollow cathode discharge in pure hydrogen is not possible.

  17. Review of recent progresses on flexible oxide semiconductor thin film transistors based on atomic layer deposition processes

    Science.gov (United States)

    Sheng, Jiazhen; Han, Ki-Lim; Hong, TaeHyun; Choi, Wan-Ho; Park, Jin-Seong

    2018-01-01

    The current article is a review of recent progress and major trends in the field of flexible oxide thin film transistors (TFTs), fabricating with atomic layer deposition (ALD) processes. The ALD process offers accurate controlling of film thickness and composition as well as ability of achieving excellent uniformity over large areas at relatively low temperatures. First, an introduction is provided on what is the definition of ALD, the difference among other vacuum deposition techniques, and the brief key factors of ALD on flexible devices. Second, considering functional layers in flexible oxide TFT, the ALD process on polymer substrates may improve device performances such as mobility and stability, adopting as buffer layers over the polymer substrate, gate insulators, and active layers. Third, this review consists of the evaluation methods of flexible oxide TFTs under various mechanical stress conditions. The bending radius and repetition cycles are mostly considering for conventional flexible devices. It summarizes how the device has been degraded/changed under various stress types (directions). The last part of this review suggests a potential of each ALD film, including the releasing stress, the optimization of TFT structure, and the enhancement of device performance. Thus, the functional ALD layers in flexible oxide TFTs offer great possibilities regarding anti-mechanical stress films, along with flexible display and information storage application fields. Project supported by the National Research Foundation of Korea (NRF) (No. NRF-2017R1D1A1B03034035), the Ministry of Trade, Industry & Energy (No. #10051403), and the Korea Semiconductor Research Consortium.

  18. A new highly automated sputter equipment for in situ investigation of deposition processes with synchrotron radiation

    Energy Technology Data Exchange (ETDEWEB)

    Doehrmann, Ralph; Botta, Stephan; Buffet, Adeline; Santoro, Gonzalo; Schlage, Kai; Schwartzkopf, Matthias; Risch, Johannes F. H.; Mannweiler, Roman; Roth, Stephan V. [DESY, Deutsches Elektronen-Synchrotron, Notkestrasse 85, D-22607 Hamburg (Germany); Bommel, Sebastian [DESY, Deutsches Elektronen-Synchrotron, Notkestrasse 85, D-22607 Hamburg (Germany); Institut fuer Physik, Humboldt-Universitaet zu Berlin, Newtonstr. 15, D-12489 Berlin (Germany); Brunner, Simon; Metwalli, Ezzeldin; Mueller-Buschbaum, Peter [Lehrstuhl fuer Funktionelle Materialien, Physik-Department, Technische Universitaet Muenchen, James-Franck-Str. 1, D-85748 Garching (Germany)

    2013-04-15

    HASE (Highly Automated Sputter Equipment) is a new mobile setup developed to investigate deposition processes with synchrotron radiation. HASE is based on an ultra-high vacuum sputter deposition chamber equipped with an in-vacuum sample pick-and-place robot. This enables a fast and reliable sample change without breaking the vacuum conditions and helps to save valuable measurement time, which is required for experiments at synchrotron sources like PETRA III at DESY. An advantageous arrangement of several sputter guns, mounted on a rotative flange, gives the possibility to sputter under different deposition angles or to sputter different materials on the same substrate. The chamber is also equipped with a modular sample stage, which allows for the integration of different sample environments, such as a sample heating and cooling device. The design of HASE is unique in the flexibility. The combination of several different sputtering methods like standard deposition, glancing angle deposition, and high pressure sputter deposition combined with heating and cooling possibil-ities of the sample, the large exit windows, and the degree of automation facilitate many different grazing incidence X-ray scattering experiments, such as grazing incidence small and wide angle X-ray scattering, in one setup. In this paper we describe in detail the design and the performance of the new equipment and present the installation of the HASE apparatus at the Micro and Nano focus X-ray Scattering beamline (MiNaXS) at PETRA III. Furthermore, we describe the measurement options and present some selected results. The HASE setup has been successfully commissioned and is now available for users.

  19. A new highly automated sputter equipment for in situ investigation of deposition processes with synchrotron radiation

    Science.gov (United States)

    Döhrmann, Ralph; Botta, Stephan; Buffet, Adeline; Santoro, Gonzalo; Schlage, Kai; Schwartzkopf, Matthias; Bommel, Sebastian; Risch, Johannes F. H.; Mannweiler, Roman; Brunner, Simon; Metwalli, Ezzeldin; Müller-Buschbaum, Peter; Roth, Stephan V.

    2013-04-01

    HASE (Highly Automated Sputter Equipment) is a new mobile setup developed to investigate deposition processes with synchrotron radiation. HASE is based on an ultra-high vacuum sputter deposition chamber equipped with an in-vacuum sample pick-and-place robot. This enables a fast and reliable sample change without breaking the vacuum conditions and helps to save valuable measurement time, which is required for experiments at synchrotron sources like PETRA III at DESY. An advantageous arrangement of several sputter guns, mounted on a rotative flange, gives the possibility to sputter under different deposition angles or to sputter different materials on the same substrate. The chamber is also equipped with a modular sample stage, which allows for the integration of different sample environments, such as a sample heating and cooling device. The design of HASE is unique in the flexibility. The combination of several different sputtering methods like standard deposition, glancing angle deposition, and high pressure sputter deposition combined with heating and cooling possibil-ities of the sample, the large exit windows, and the degree of automation facilitate many different grazing incidence X-ray scattering experiments, such as grazing incidence small and wide angle X-ray scattering, in one setup. In this paper we describe in detail the design and the performance of the new equipment and present the installation of the HASE apparatus at the Micro and Nano focus X-ray Scattering beamline (MiNaXS) at PETRA III. Furthermore, we describe the measurement options and present some selected results. The HASE setup has been successfully commissioned and is now available for users.

  20. Technique for the estimation of surface temperatures from embedded temperature sensing for rapid, high energy surface deposition.

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, Tyson R.; Schunk, Peter Randall; Roberts, Scott Alan

    2014-07-01

    Temperature histories on the surface of a body that has been subjected to a rapid, highenergy surface deposition process can be di cult to determine, especially if it is impossible to directly observe the surface or attach a temperature sensor to it. In this report, we explore two methods for estimating the temperature history of the surface through the use of a sensor embedded within the body very near to the surface. First, the maximum sensor temperature is directly correlated with the peak surface temperature. However, it is observed that the sensor data is both delayed in time and greatly attenuated in magnitude, making this approach unfeasible. Secondly, we propose an algorithm that involves tting the solution to a one-dimensional instantaneous energy solution problem to both the sensor data and to the results of a one-dimensional CVFEM code. This algorithm is shown to be able to estimate the surface temperature 20 C.

  1. Physical deposition of thin polyimide layers by applying an argon plasma assisted process

    Energy Technology Data Exchange (ETDEWEB)

    Dimov, D; Georgiev, A; Spassova, E; Assa, J; Dineff, P; Danev, G, E-mail: dean@clf.bas.b

    2010-11-01

    A novel method for physical deposition of thin polyimide layers by applying an argon plasma assisted process has been developed. The influence of the plasma on the combined molecular flux of the two thermally evaporated precursors - 4,4'- oxydianiline and pyromellitic dianhydride was investigated. The process parameters were changed in the limlts 0,4 - 2 A for the anode current and 80 - 170 V for the anode voltage. Their influence was studied using FTIR spectroscopy and electron microscopy techniques. It was proposed that the plasma flux crossing the molecular flows of the polyimide precursors enhances the imidization process by partly activating the precursor molecules in the gas phase.

  2. Influence of Energy and Temperature in Cluster Coalescence Induced by Deposition

    Directory of Open Access Journals (Sweden)

    J. C. Jiménez-Sáez

    2012-01-01

    Full Text Available Coalescence induced by deposition of different Cu clusters on an epitaxial Co cluster supported on a Cu(001 substrate is studied by constant-temperature molecular dynamics simulations. The degree of epitaxy of the final system increases with increasing separation between the centres of mass of the projectile and target clusters during the collision. Structure, roughness, and epitaxial order of the supported cluster also influence the degree of epitaxy. The effect of energy and temperature is determinant on the epitaxial condition of the coalesced cluster, especially both factors modify the generation, growth and interaction among grains. A higher temperature favours the epitaxial growth for low impact parameters. A higher energy contributes to the epitaxial coalescence for any initial separation between the projectile and target clusters. The influence of projectile energy is notably greater than the influence of temperature since higher energies allow greater and instantaneous atomic reorganizations, so that the number of arisen grains just after the collision becomes smaller. The appearance of grain boundary dislocations is, therefore, a decisive factor in the epitaxial growth of the coalesced cluster.

  3. SU-G-TeP3-13: The Role of Nanoscale Energy Deposition in the Development of Gold Nanoparticle-Enhanced Radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Kirkby, C [Jack Ady Cancer Centre, Lethbridge, AB (Canada); The University of Calgary, Calgary, AB (Canada); Koger, B [The University of Calgary, Calgary, AB (Canada); Suchowerska, N [Chris O’Brien Lifehouse Camperdown, NSW (Australia); McKenzie, D [University of Sydney, Sydney, NSW (Australia)

    2016-06-15

    Purpose: Gold nanoparticles (GNPs) can enhance radiotherapy effects. The high photoelectric cross section of gold relative to tissue, particularly at lower energies, leads to localized dose enhancement. However in a clinical context, photon energies must also be sufficient to reach a target volume at a given depth. These properties must be balanced to optimize such a therapy. Given that nanoscale energy deposition patterns around GNPs play a role in determining biological outcomes, in this work we seek to establish their role in this optimization process. Methods: The PENELOPE Monte Carlo code was used to generate spherical dose deposition kernels in 1000 nm diameter spheres around 50 nm diameter GNPs in response to monoenergetic photons incident on the GNP. Induced “lesions” were estimated by either a local effect model (LEM) or a mean dose model (MDM). The ratio of these estimates was examined for a range of photon energies (10 keV to 2 MeV), for three sets of linear-quadratic parameters. Results: The models produce distinct differences in expected lesion values, the lower the alpha-beta ratio, the greater the difference. The ratio of expected lesion values remained constant within 5% for energies of 40 keV and above across all parameter sets and rose to a difference of 35% for lower energies only for the lowest alpha-beta ratio. Conclusion: Consistent with other work, these calculations suggest nanoscale energy deposition patterns matter in predicting biological response to GNP-enhanced radiotherapy. However the ratio of expected lesions between the different models is largely independent of energy, indicating that GNP-enhanced radiotherapy scenarios can be optimized in photon energy without consideration of the nanoscale patterns. Special attention may be warranted for energies of 20 keV or below and low alpha-beta ratios.

  4. THE ROLE OF CRYOGENIC PROCESSES IN THE FORMATION OF LOESS DEPOSITS

    Directory of Open Access Journals (Sweden)

    Vyacheslav N. Konishchev

    2015-01-01

    Full Text Available The paper describes a new approach to the analysis of the genetic nature of mineral substances in loess deposits. In permafrost under the influence of multiple alternate freezing and thawing in dispersed deposits, quartz particles accumulate the 0.05-0.01 mm fraction, while feldspars are crushed to a coarse fraction of 0.1-0.05 mm. In dispersed sediments formed in temperate and warm climatic zones, the granulometric spectrum of quartz and feldspar has the opposite pattern. The proposed methodology is based on a differential analysis of the distribution of these minerals by the granulometric spectrum. We have proposed two criteria - the coefficient of cryogenic contrast (CCC and the coefficient of distribution of heavy minerals, which allow determination of the degree of participation of cryogenic processes in the formation of loess sediments and processes of aeolian or water sedimentation.

  5. Lightning driven inner radiation belt energy deposition into the atmosphere: regional and global estimates

    Directory of Open Access Journals (Sweden)

    C. J. Rodger

    2005-12-01

    Full Text Available In this study we examine energetic electron precipitation fluxes driven by lightning, in order to determine the global distribution of energy deposited into the middle atmosphere. Previous studies using lightning-driven precipitation burst rates have estimated losses from the inner radiation belts. In order to confirm the reliability of those rates and the validity of the conclusions drawn from those studies, we have analyzed New Zealand data to test our global understanding of troposphere to magnetosphere coupling. We examine about 10000h of AbsPAL recordings made from 17 April 2003 through to 26 June 2004, and analyze subionospheric very-low frequency (VLF perturbations observed on transmissions from VLF transmitters in Hawaii (NPM and western Australia (NWC. These observations are compared with those previously reported from the Antarctic Peninsula. The perturbation rates observed in the New Zealand data are consistent with those predicted from the global distribution of the lightning sources, once the different experimental configurations are taken into account. Using lightning current distributions rather than VLF perturbation observations we revise previous estimates of typical precipitation bursts at L~2.3 to a mean precipitation energy flux of ~1×10-3 ergs cm-2s-1. The precipitation of energetic electrons by these bursts in the range L=1.9-3.5 will lead to a mean rate of energy deposited into the atmosphere of 3×10-4 ergs cm-2min-1, spatially varying from a low of zero above some ocean regions to highs of ~3-6×10-3 ergs cm-2min-1 above North America and its conjugate region.

  6. Lightning driven inner radiation belt energy deposition into the atmosphere: regional and global estimates

    Directory of Open Access Journals (Sweden)

    C. J. Rodger

    2005-12-01

    Full Text Available In this study we examine energetic electron precipitation fluxes driven by lightning, in order to determine the global distribution of energy deposited into the middle atmosphere. Previous studies using lightning-driven precipitation burst rates have estimated losses from the inner radiation belts. In order to confirm the reliability of those rates and the validity of the conclusions drawn from those studies, we have analyzed New Zealand data to test our global understanding of troposphere to magnetosphere coupling. We examine about 10000h of AbsPAL recordings made from 17 April 2003 through to 26 June 2004, and analyze subionospheric very-low frequency (VLF perturbations observed on transmissions from VLF transmitters in Hawaii (NPM and western Australia (NWC. These observations are compared with those previously reported from the Antarctic Peninsula. The perturbation rates observed in the New Zealand data are consistent with those predicted from the global distribution of the lightning sources, once the different experimental configurations are taken into account. Using lightning current distributions rather than VLF perturbation observations we revise previous estimates of typical precipitation bursts at L~2.3 to a mean precipitation energy flux of ~1×10-3 ergs cm-2s-1. The precipitation of energetic electrons by these bursts in the range L=1.9-3.5 will lead to a mean rate of energy deposited into the atmosphere of 3×10-4 ergs cm-2min-1, spatially varying from a low of zero above some ocean regions to highs of ~3-6×10-3 ergs cm-2min-1 above North America and its conjugate region.

  7. Use of supercritical fluid solution expansion processes for drug delivery, particle synthesis, and thin film deposition

    Energy Technology Data Exchange (ETDEWEB)

    Hybertson, B.M.

    1992-01-01

    Properties of the gases and aerosols resulting from the expansion of supercritical fluid solutions were studied. Film deposition, particle formation, and drug delivery processes using supercritical fluids were developed. Thin films of palladium, copper, aluminum, silver, and silicon dioxide were deposited by a method called supercritical fluid transport-chemical deposition (SFT-CD). In each case, a precursor compound was dissolved in a supercritical fluid and the solution was allowed to expand through a restrictor nozzle into a reaction chamber at subcritical pressure, resulting in the formation of aerosol particles of the precursor. A chemical reaction was induced to occur at the surface of a substrate, resulting in deposition of a thin film. Micron-sized particles of aluminum fluoride and copper oxide were synthesized by a method called supercritical fluid transport-chemical formation of particles (SFT-CFP). The process was similar to that in SFT-CD, but the chemical reactions were induced to occur in the gas phase instead of at a substrate surface, resulting in the formation of fine particles. A new method of pulmonary drug delivery called supercritical fluid drug delivery (SFDD) was conceived and demonstrated. In SFDD a drug compound is dissolved in a supercritical fluid, and the solution is allowed to expand through a restrictor nozzle. The resultant aerosol is directly inhaled by a human or animal subject and the fine drug particles are deposited in the lungs. Menthol, vanillin, camphor, cholesterol, Sudan III, and Oil Blue N were used as model drug compounds for SFDD. Delivery of [alpha]-tocopherol to rat lung tissue was demonstrated, with observed increases of 80-290% above background levels.

  8. Electric energy consumption in the cotton textile processing stages

    Energy Technology Data Exchange (ETDEWEB)

    Palamutcu, S. [Textile Engineering Department, Pamukkale University, Engineering Faculty, 20070 Kinikli, Denizli (Turkey)

    2010-07-15

    Electric energy is one of the primary energy sources consumpted in cotton textile processing. Current energy cost rate is reported about 8-10% in the total production cost of an ordinary textile product manufactured in Turkey. Significantly important share of this energy cost is electric energy. The aim of this paper was to investigate unit electric energy consumption of cotton textile processing stages using real-time measurements method. Actual and estimated Specific Energy Consumption (SEC) values for electric energy was calculated in the cotton textile processing stages of spinning, warping-sizing, weaving, wet processing and clothing manufacturing. Actual electric energy consumption data are gathered from monthly records of the involved plant managements. Estimated electric energy consumption data is gathered through on-site measurement. Actual and estimated electric energy consumption data and monthly production quantities of the corresponding months are used to facilitate specific electric energy consumption of the plants. It is found that actual electric energy consumption amount per unit textile product is higher than the estimated electric energy consumption amount per unit textile product of each involved textile processing stages. (author)

  9. Energy Performance of Verandas in the Building Retrofit Process

    National Research Council Canada - National Science Library

    Rossano Albatici; Francesco Passerini; Jens Pfafferott

    2016-01-01

      Passive solar elements for both direct and indirect gains, are systems used to maintain a comfortable living environment while saving energy, especially in the building energy retrofit and adaptation process...

  10. Reactor and process design in sustainable energy technology

    CERN Document Server

    Shi, Fan

    2014-01-01

    Reactor Process Design in Sustainable Energy Technology compiles and explains current developments in reactor and process design in sustainable energy technologies, including optimization and scale-up methodologies and numerical methods. Sustainable energy technologies that require more efficient means of converting and utilizing energy can help provide for burgeoning global energy demand while reducing anthropogenic carbon dioxide emissions associated with energy production. The book, contributed by an international team of academic and industry experts in the field, brings numerous reactor design cases to readers based on their valuable experience from lab R&D scale to industry levels. It is the first to emphasize reactor engineering in sustainable energy technology discussing design. It provides comprehensive tools and information to help engineers and energy professionals learn, design, and specify chemical reactors and processes confidently. Emphasis on reactor engineering in sustainable energy techn...

  11. An Investigation of the CSC-MIG Welding Process for Deposition of Conventional, Ultrafine and Nanostructured MMC Coatings

    Science.gov (United States)

    Vespa, Patrick

    Welding based coating deposition techniques allow high rates of material deposition and form a permanent metallurgical bond between the coating and the substrate material. Welding based methods can also provide an economic alternative over other industrial coating deposition processes where high initial capital investment and running costs can be restrictive. As with all technological sectors, the need for new and improved machinery and processes to meet industrial needs provides a drive for continued research. The controlled short-circuit MIG (CSC-MIG) welding system is a newly developed welding apparatus built to overcome several shortcomings associated with traditional MIG welding. It allows for greater control of many welding parameters and has reduced heat input during deposition when compared with conventional MIG welding systems. This project was conducted to understand the CSC-MIG welding system as a process and as a hardfacing deposition technique through examination of the microstructural features and transformations of Ni/WC coatings. Several coatings deposited with a Ni/WC electrode wire, with heat input ranging between 10 J/mm and 110 J/mm, were examined. It was found that the detrimental decarburization reactions acting on the WC particles, as seen in thermal spray systems, do not occur when welding with the CSC-MIG. Although the energy input during welding with the CSC-MIG system is significantly lower than for traditional MIG, dissolution of the reinforcing phase is an issue to be contended with and must be minimized through proper selection of welding parameters. Precipitation of a reaction layer around the WC/W2C reinforcing phase was identified as WC; the average thickness of which increased from 3.8 mum to 7.2 mum for the low and high heat input condition, respectively. Precipitation of newly formed WC particles was also observed; their size distribution increased from D50 = 2.4 mum in the low heat input weldment to D50 = 6.75 mum in the high

  12. Depositional processes of alluvial fans along the Hilina Pali fault scarp, Island of Hawaii

    Science.gov (United States)

    Morgan, Alexander M.; Craddock, Robert A.

    2017-11-01

    A series of previously unstudied alluvial fans are actively forming along the Hilina Pali escarpment on the south flank of Kīlauea volcano on the Island of Hawaii. These fans are characterized by their steep slopes, coarse grain sizes, and lobate surface morphology. Fans are fed by bedrock channels that drain from the Ka'ū Desert, but sediment is mostly sourced from deeply eroded alcoves carved into the Hilina Pali. Examination of recent deposits indicates that the fans are dominantly constructed from gravel and larger sized sediment. Flow discharges calculated using field measurements of channel geometries and the Manning equation indicate that events inducing sediment transport are of high magnitude and occur during high intensity precipitation events, including Kona storms. The fans along the Hilina Pali appear to be a rare example of fans formed predominately from sieve lobe deposition owing to the area's high slopes, high discharge, coarse bedload, and limited supply of fine-grained sediment. Given such conditions, sieve lobe deposition can form large lobes consisting of boulder-sized material, which may have implications for the identification of depositional processes when interpreting the stratigraphic record.

  13. Ellipsometry study of process deposition of amorphous Indium Gallium Zinc Oxide sputtered thin films

    Energy Technology Data Exchange (ETDEWEB)

    Talagrand, C., E-mail: talagrand@emse.fr [Ecole des Mines de Saint-Etienne CMP-GC, Dept PS2, Gardanne, 880 route de Mimet (France); Boddaert, X. [Ecole des Mines de Saint-Etienne CMP-GC, Dept PS2, Gardanne, 880 route de Mimet (France); Selmeczi, D.G.; Defranoux, C. [Semilab Semiconductor Physics Laboratory Co. Ltd., Budapest, 1117 (Hungary); Collot, P. [Ecole Nationale Supérieure d' Arts et Métiers ParisTech, Aix-en-Provence, 2 cours des Arts et Métiers (France)

    2015-09-01

    This paper reports on an InGaZnO optical study by spectrometric ellipsometry. First of all, the fitting results of different models and different structures are analysed to choose the most appropriate model. The Tauc–Lorentz model is suitable for thickness measurements but a more complex model allows the refractive index and extinction coefficient to be extracted more accurately. Secondly, different InGaZnO process depositions are carried out in order to investigate stability, influence of deposition time and uniformity. Films present satisfactory optical stability over time. InGaZnO optical property evolution as a function of deposition time is related to an increase in temperature. To understand the behaviour of uniformity, mapping measurements are correlated to thin film resistivity. Results show that temperature and resputtering are the two phenomena that affect IGZO uniformity. - Highlights: • Model and structure are investigated to fit IGZO ellipsometric angles. • Maximum refractive index rises with substrate temperature and thus deposition time. • Resputtering leads to inhomogeneity in IGZO electrical and optical properties.

  14. Instrumentation and control for fossil-energy processes

    Energy Technology Data Exchange (ETDEWEB)

    1982-09-01

    The 1982 symposium on instrumentation and control for fossil energy processes was held June 7 through 9, 1982, at Adam's Mark Hotel, Houston, Texas. It was sponsored by the US Department of Energy, Office of Fossil Energy; Argonne National Laboratory; and the Society for Control and Instrumentation of Energy Processes. Fifty-two papers have been entered individually into EDB and ERA; eleven papers had been entered previously from other sources. (LTN)

  15. Refractories for Industrial Processing. Opportunities for Improved Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hayden, H. Wayne [Metals Manufacture Process and Controls Technology, Inc., Oak Ridge, TN (United States); Angelini, Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moore, Robert E. [R.E. Moore Associates, Maricopa, AZ (United States); Headrick, William L. [R.E. Moore Associates, Maricopa, AZ (United States)

    2005-01-01

    Refractories are a class of materials of critical importance to manufacturing industries with high-temperature unit processes. This study describes industrial refractory applications and identifies refractory performance barriers to energy efficiency for processing. The report provides recommendations for R&D pathways leading to improved refractories for energy-efficient manufacturing and processing.

  16. Partition of metabolizable energy, and prediction of growth performance and lipid deposition in broiler chickens.

    Science.gov (United States)

    Carré, B; Juin, H

    2015-06-01

    The study presented here consisted of the calculation of cross relationships between growth performance parameters, body growth composition, and feed characteristics, using data from an experiment reported in 2 previous publications. In the previous experiment, 30 pelleted diets were given to broiler chickens (8/diet) (21 to 35 d) for in vivo measurement and prediction of AMEn and net energy (NE) values of diets, using 3 trials with 10 diets/trial. In the course of NE determination, individual values for growth, feed intake, and deposition of lipid and protein were measured. Average energy deposited as lipid and protein represented 25.4 and 19.1% AME intake, respectively. Using a multiple regression predicting AME intake, the partial efficiencies of AME for energy deposition as lipid and protein were calculated to be 91.6 and 67.3%, respectively, and the daily amount of AME required for maintenance was evaluated at 0.683 MJ/kg BW0.7. The mean diet NE/AMEn ratios were predicted by an equation combining the lipid content of body growth (positive coefficient) and the apparent digestible protein (ADP) to AMEn ratio (ADP/AMEn), with a quadratic expression for the latter variable. This quadratic response expressed a positive asymptotic relationship, with a plateau for ADP/AMEn values above 1.45 [%/(MJ/kg)]. The equations predicting growth always included either the dietary percentage of water-insoluble cell wall or the AMEn value. The other major parameters predicting growth were either the lipid content of body growth or the CP/AMEn ratio. In many cases, quadratic responses were observed in growth prediction equations. Regressions predicting feed efficiency showed only linear responses. Feed efficiency was predicted precisely by multiple linear regressions based only on AMEn and a dietary protein parameter. According to these regressions, 1% CP was equivalent to 0.247 MJ/kg AMEn in terms of feed efficiency. The most efficient regression predicting the individual lipid

  17. Phosphor Deposits of β-Sialon:Eu2+ Mixed with SnO2 Nanoparticles Fabricated by the Electrophoretic Deposition (EPD) Process

    Science.gov (United States)

    Zhang, Chenning; Uchikoshi, Tetsuo; Liu, Lihong; Sakka, Yoshio; Hirosaki, Naoto

    2014-01-01

    The phosphor deposits of the β-sialon:Eu2+ mixed with various amounts (0–1 g) of the SnO2 nanoparticles were fabricated by the electrophoretic deposition (EPD) process. The mixed SnO2 nanoparticles was observed to cover onto the particle surfaces of the β-sialon:Eu2+ as well as fill in the voids among the phosphor particles. The external and internal quantum efficiencies (QEs) of the prepared deposits were found to be dependent on the mixing amount of the SnO2: by comparing with the deposit without any mixing (48% internal and 38% external QEs), after mixing the SnO2 nanoparticles, the both QEs were improved to 55% internal and 43% external QEs at small mixing amount (0.05 g); whereas, with increasing the mixing amount to 0.1 and 1 g, they were reduced to 36% and 29% for the 0.1 g addition and 15% and 12% l QEs for the 1 g addition. More interestingly, tunable color appearances of the deposits prepared by the EPD process were achieved, from yellow green to blue, by varying the addition amount of the SnO2, enabling it as an alternative technique instead of altering the voltage and depositing time for the color appearance controllability. PMID:28788639

  18. Phosphor Deposits of β-Sialon:Eu2+ Mixed with SnO₂ Nanoparticles Fabricated by the Electrophoretic Deposition (EPD) Process.

    Science.gov (United States)

    Zhang, Chenning; Uchikoshi, Tetsuo; Liu, Lihong; Sakka, Yoshio; Hirosaki, Naoto

    2014-05-06

    The phosphor deposits of the β-sialon:Eu2+ mixed with various amounts (0-1 g) of the SnO₂ nanoparticles were fabricated by the electrophoretic deposition (EPD) process. The mixed SnO₂ nanoparticles was observed to cover onto the particle surfaces of the β-sialon:Eu2+ as well as fill in the voids among the phosphor particles. The external and internal quantum efficiencies (QEs) of the prepared deposits were found to be dependent on the mixing amount of the SnO₂: by comparing with the deposit without any mixing (48% internal and 38% external QEs), after mixing the SnO₂ nanoparticles, the both QEs were improved to 55% internal and 43% external QEs at small mixing amount (0.05 g); whereas, with increasing the mixing amount to 0.1 and 1 g, they were reduced to 36% and 29% for the 0.1 g addition and 15% and 12% l QEs for the 1 g addition. More interestingly, tunable color appearances of the deposits prepared by the EPD process were achieved, from yellow green to blue, by varying the addition amount of the SnO₂, enabling it as an alternative technique instead of altering the voltage and depositing time for the color appearance controllability.

  19. Advanced Materials Enabled by Atomic Layer Deposition for High Energy Density Rechargeable Batteries

    Science.gov (United States)

    Chen, Lin

    In order to meet the ever increasing energy needs of society and realize the US Department of Energy (DOE)'s target for energy storage, acquiring a fundamental understanding of the chemical mechanisms in batteries for direct guidance and searching novel advanced materials with high energy density are critical. To realize rechargeable batteries with superior energy density, great cathodes and excellent anodes are required. LiMn2O4 (LMO) has been considered as a simpler surrogate for high energy cathode materials like NMC. Previous studies demonstrated that Al2O3 coatings prepared by atomic layer deposition (ALD) improved the capacity of LMO cathodes. This improvement was attributed to a reduction in surface area and diminished Mn dissolution. However, here we propose a different mechanism for ALD Al 2O3 on LMO based on in-situ and ex-situ investigations coupled with density functional theory calculations. We discovered that Al2O 3 not only coats the LMO, but also dopes the LMO surface with Al leading to changes in the Mn oxidation state. Different thicknesses of Al2O 3 were deposited on nonstoichiometric LiMn2O4 for electrochemical measurements. The LMO treated with one cycle of ALD Al2O3 (1xAl 2O3 LMO) to produce a sub-monolayer coating yielded a remarkable initial capacity, 16.4% higher than its uncoated LMO counterpart in full cells. The stability of 1xAl2O3 LMO is also much better as a result of stabilized defects with Al species. Furthermore, 4xAl 2O3 LMO demonstrates remarkable capacity retention. Stoichiometric LiMn2O4 was also evaluated with similar improved performance achieved. All superior results, accomplished by great stability and reduced Mn dissolution, is thanks to the synergetic effects of Al-doping and ALD Al2O 3 coating. Turning our attention to the anode, we again utilized aluminum oxide ALD to form conformal films on lithium. We elaborately designed and studied, for the first time, the growth mechanism during Al2O3 ALD on lithium metal in

  20. Fast electron transport and spatial energy deposition in imploded fast ignition cone-in-shell targets

    Science.gov (United States)

    Jarrott, Leonard

    2014-10-01

    We report on the first experimental observation and model validation of the spatial energy deposition of fast electrons into the imploded, high-density core of integrated cone-in-shell fast ignition experiments on OMEGA. Spatial energy deposition was characterized via fast electron produced K α fluorescence from a Cu tracer added to the CD shell. 2-D images of the Cu K α fluorescence were obtained using a spherically bent Bragg crystal imager. 54 of the 60 OMEGA beams (18 kJ) were used for fuel assembly, and the high intensity EP beam (10 ps, 0.5--1.5 kJ, Ip >1019 W/cm2) , was focused onto the inner cone tip to produce fast electrons. Cu K α emission from a 300 μm region surrounding the cone tip correlated well with the predicted core size from radiation-hydrodynamic simulations of the shell implosion. The emission also emanated from as far back as 100 μm from the cone tip, indicative of an electron source position with a large standoff distance from the cone tip, consistent with the presence of an extended pre-plasma from the EP pre-pulse. We observed a simultaneous increase in both K α yield (up to 70%) and thermal neutron number (up to 2×) with increasing EP beam energy. K α yield data also show an improved energy coupling using the high contrast EP pulse. Comprehensive simulations of the electron production within the cone and subsequent transport into the imploded core have been performed using the implicit PIC code LSP and the hybrid-PIC code ZUMA. These simulations explain the observed K α shape and yield trends and identify parameters that constrain energy coupling into the compressed core. This work was performed under the auspices of U.S. DOE under Contracts DE-FC02-04ER54789 (FSC), DE-FG02-05ER54834 (ACE) and DE-NA0000854 (NLUF).

  1. REE concentration processes in ion adsorption deposits: Evidence from Madagascar and China.

    Science.gov (United States)

    Smith, Martin; Estrade, Guillaume; Marquis, Eva; Goodenough, Kathryn; Nasun, Peter; Cheng, Xu; Kynicky, Jindrich

    2017-04-01

    Lateritic clay deposits, where the rare earth elements (REE) occur adsorbed to clay mineral surfaces, are the world's dominant supply of heavy REE (Gd-Lu). These deposits are currently only mined in China where there is a reported heavy REE enrichment, but other deposits are currently under exploration in Brazil, the Philippines and Madagascar. Concentration of REE within IADs has been proposed to be a dominantly supergene process, where easily degradable REE-minerals (e.g. REE-fluorcarbonates) break down and release REE that are then adsorbed to clay minerals resulting in HREE enrichment. Here we present data from the Ambohimirahavavy Complex, Madagascar, and compare them to data from mineralised profiles in China, with the aim of further constraining the formation and REE enrichment processes in ion adsorption deposits. Bulk rock total REE contents from Madagascar vary from 400-5000ppm, with the HREE varying from 10 to 20% of the TREE. Ammonium Sulphate leaches (designed to remove clay-adsorbed REE) of laterite show leachable TREE from 130-500ppm, with no preferential HREE adsorption. Within the sequential extraction procedure the reducible fraction (hydroxylammonium chloride leach) showed the highest REE, but this is largely attributable to Ce4+ in oxide layers. Analysis of laterite profiles show that the REE distribution is heterogeneous, with control from both bedrock heterogeneity, and the hydrological variation between pedolith and saprolith. Similar patterns are seen in Chinese profiles from Jiangxi province. X-ray diffraction shows the clay fraction in all sites is dominated by kaolinite and halloysite. These data are consistent with experimental data which show that kaolinite is only HREE selective in high ionic strength solutions (Coppin et al., 2002), and suggest that HREE enrichment in lateritic deposits may be a function of exceptional bed rock conditions. Petrographic investigation of the Zhaibei granite, immediately underlying HREE enriched

  2. Efficiency of manufacturing processes energy and ecological perspectives

    CERN Document Server

    Li, Wen

    2015-01-01

     This monograph presents a reliable methodology for characterising the energy and eco-efficiency of unit manufacturing processes. The Specific Energy Consumption, SEC, will be identified as the key indicator for the energy efficiency of unit processes.  An empirical approach will be validated on different machine tools and manufacturing processes to depict the relationship between process parameters and energy consumptions. Statistical results and additional validation runs will corroborate the high level of accuracy in predicting the energy consumption. In relation to the eco-efficiency, the value and the associated environmental impacts of  manufacturing processes will also be discussed. The interrelationship between process parameters, process value and the associated environmental impact will be integrated in the evaluation of eco-efficiency. The book concludes with a further investigation of the results in order to develop strategies for further efficiency improvement. The target audience primarily co...

  3. Energy deposition profile for modification proposal of ISOLDE’s HRS Beam Dump, from FLUKA simulations

    CERN Document Server

    Vlachoudis, V

    2014-01-01

    The current ISOLDE HRS beam dump has been found to be unsuitable on previous simulations, due to thermomechanical stresses. In this paper a proposal for modifying HRS dump is studied using FLUKA. The energy deposited in this modified beam dump and the amount of neutrons streaming to the tunnel area are scored and compared with the simulation of current dump. Two versions of the modification have been assessed, determining which of them is more desirable in terms of influence of radiation on ISOLDE’s tunnel. Finally, a rough estimate of temperature raise in the modified dump is shown. Further conclusions on the adequacy of these modifications need to include the thermomechanical calculations’ results, based on those presented here.

  4. Energy and nutrient deposition and excretion in the reproducing sow: model development and evaluation

    DEFF Research Database (Denmark)

    Hansen, A V; Strathe, A B; Theil, Peter Kappel

    2014-01-01

    emission, manure carbon excretion, and manure production. The model was evaluated using independent data sets from the literature using root mean square prediction error (RMSPE) and concordance correlation coefficients. The gestation module predicted body fat gain better than body protein gain, which...... excretion and composition and methane emissions on a daily basis. The model was structured to contain gestation and lactation modules, which can be run separately or sequentially, with outputs from the gestation module used as inputs to the lactation module. In the gestating module, energy and protein...... production, and maternal growth with body tissue losses constrained within biological limits. Global sensitivity analysis showed that nonlinearity in the parameters was small. The model outputs considered were the total protein and fat deposition, average urinary and fecal N excretion, average methane...

  5. Energy deposition in selected-mammalian cell for several-MeV single-proton beam

    Energy Technology Data Exchange (ETDEWEB)

    Ding, K. [Beijing Jiaotong Univ., Institute of Biological Science and Technology, P.R. (China); Yu, Z. [Chinese Academy of Science, The Key Lab. of Ion-Beam Bioengineering, P.R. (China)

    2007-05-15

    The phenomena resulting from interaction between ion beam and mammalian cell pose important problems for biological applications. Classic Bethe-Bloch theory utilizing attached V79 mammalian cell has been conducted in order to establish the stopping powers of the mammalian cell for several-MeV single-proton microbeam. Based on the biological structure of the mammalian cell, a physical model is proposed which presumes that the attached cell is a simple MWM model. According to this model and Monte Carlo simulation, we studied the energy deposition and its ratio on the selected attached mammalian cell for MeV proton implantation. We found that the Bragg peak region of several-MeV energetic proton is beyond the thickness of the selected attached mammalian cell.

  6. Model Property Based Material Balance and Energy Conservation Analysis for Process Industry Energy Transfer Systems

    OpenAIRE

    Fumin Ma; Gregory M. P. O’Hare; Tengfei Zhang; Michael J. O’Grady

    2015-01-01

    Conventional historical data based material and energy balance analyses are static and isolated computations. Such methods cannot embody the cross-coupling effect of energy flow, material flow and information flow in the process industry; furthermore, they cannot easily realize the effective evaluation and comparison of different energy transfer processes by alternating the model module. In this paper, a novel method for material balance and energy conservation analysis of process industry en...

  7. Bioactive glass-ceramic coatings prepared by pulsed laser deposition from RKKP targets (sol-gel vs melt-processing route)

    Energy Technology Data Exchange (ETDEWEB)

    Rau, J.V., E-mail: giulietta.rau@ism.cnr.it [Istituto di Struttura della Materia, Consiglio Nazionale delle Ricerche, Via del Fosso del Cavaliere, 100-00133 Rome (Italy); Teghil, R. [Universita della Basilicata, Dipartimento di Chimica ' A.M. Tamburro' , Via dell' Ateneo Lucano, 10-85100 Potenza (Italy); CNR-IMIP U.O.S. di Potenza, Zona Industriale di Tito scalo (PZ) (Italy); Fosca, M. [Istituto di Struttura della Materia, Consiglio Nazionale delle Ricerche, Via del Fosso del Cavaliere, 100-00133 Rome (Italy); Universita di Roma ' La Sapienza' , Dipartimento di Chimica, Piazzale Aldo Moro, 5-00185 Rome (Italy); De Bonis, A. [Universita della Basilicata, Dipartimento di Chimica ' A.M. Tamburro' , Via dell' Ateneo Lucano, 10-85100 Potenza (Italy); CNR-IMIP U.O.S. di Potenza, Zona Industriale di Tito scalo (PZ) (Italy); Cacciotti, I.; Bianco, A. [Universita di Roma ' Tor Vergata' , Dipartimento di Ingegneria Industriale, UR INSTM ' Roma Tor Vergata' , Via del Politecnico, 1-00133 Rome (Italy); Albertini, V. Rossi [Istituto di Struttura della Materia, Consiglio Nazionale delle Ricerche, Via del Fosso del Cavaliere, 100-00133 Rome (Italy); Caminiti, R. [Universita di Roma ' La Sapienza' , Dipartimento di Chimica, Piazzale Aldo Moro, 5-00185 Rome (Italy); Ravaglioli, A. [Parco Torricelli delle Arti e delle Scienze, Via Granarolo, 64-48018 Faenza (Ra) (Italy)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Bioactive glass-ceramic coatings for bone tissue repair and regeneration. Black-Right-Pointing-Pointer Pulsed Lased Deposition allowed congruent transfer of target composition to coating. Black-Right-Pointing-Pointer Target was prepared by sol-gel process suitable for compositional tailoring. Black-Right-Pointing-Pointer Titanium, widely used for orthopaedics and dental implants, was used as substrate. Black-Right-Pointing-Pointer The physico-chemical properties of the prepared coatings are reported. -- Abstract: The deposition of innovative glass-ceramic composition (i.e. RKKP) coatings by Pulsed Lased Deposition (PLD) technique is reported. RKKP was synthesised following two methodologies: melt-processing and sol-gel, the latter being particularly suitable to tailor the compositional range. The PLD advantage with respect to other deposition techniques is the congruent transfer of the target composition to the coating. The physico-chemical properties of films were investigated by Scanning Electron and Atomic Force Microscopies, Fourier Transform Infrared Spectroscopy, Angular and Energy Dispersive X-ray Diffraction, and Vickers microhardness. The deposition performed at 12 J/cm{sup 2} and 500 Degree-Sign C allows to prepare crystalline films with the composition that replicates rather well that of the initial targets. The 0.6 {mu}m thin melt-processing RKKP films, possessing the hardness of 25 GPa, and the 4.3 {mu}m thick sol-gel films with the hardness of 17 GPa were obtained.

  8. Gaseous material capacity of open plasma jet in plasma spray-physical vapor deposition process

    Science.gov (United States)

    Liu, Mei-Jun; Zhang, Meng; Zhang, Qiang; Yang, Guan-Jun; Li, Cheng-Xin; Li, Chang-Jiu

    2018-01-01

    Plasma spray-physical vapor deposition (PS-PVD) process, emerging as a highly efficient hybrid approach, is based on two powerful technologies of both plasma spray and physical vapor deposition. The maximum production rate is affected by the material feed rate apparently, but it is determined by the material vapor capacity of transporting plasma actually and essentially. In order to realize high production rate, the gaseous material capacity of plasma jet must be fundamentally understood. In this study, the thermal characteristics of plasma were measured by optical emission spectrometry. The results show that the open plasma jet is in the local thermal equilibrium due to a typical electron number density from 2.1 × 1015 to 3.1 × 1015 cm-3. In this condition, the temperature of gaseous zirconia can be equal to the plasma temperature. A model was developed to obtain the vapor pressure of gaseous ZrO2 molecules as a two dimensional map of jet axis and radial position corresponding to different average plasma temperatures. The overall gaseous material capacity of open plasma jet, take zirconia for example, was further established. This approach on evaluating material capacity in plasma jet would shed light on the process optimization towards both depositing columnar coating and a high production rate of PS-PVD.

  9. Bio-mineralization and potential biogeochemical processes in bauxite deposits: genetic and ore quality significance

    Science.gov (United States)

    Laskou, Magdalini; Economou-Eliopoulos, Maria

    2013-08-01

    The Parnassos-Ghiona bauxite deposit in Greece of karst type is the 11th largest bauxite producer in the world. The mineralogical, major and trace-element contents and δ18O, δ12C, δ34S isotopic compositions of bauxite ores from this deposit and associated limestone provide valuable evidence for their origin and biogeochemical processes resulting in the beneficiation of low grade bauxite ores. The organic matter as thin coal layers, overlying the bauxite deposits, within limestone itself (negative δ12C isotopic values) and the negative δ34S values in sulfides within bauxite ores point to the existence of the appropriate circumstances for Fe bio-leaching and bio-mineralization. Furthermore, a consortium of microorganisms of varying morphological forms (filament-like and spherical to lenticular at an average size of 2 μm), either as fossils or presently living and producing enzymes, is a powerful factor to catalyze the redox reactions, expedite the rates of metal extraction and provide alternative pathways for metal leaching processes resulting in the beneficiation of bauxite ore.

  10. New urate depositions on dual-energy computed tomography in gouty arthritis during urate-lowering therapy.

    Science.gov (United States)

    Zhang, Zhuojun; Zhang, Xiaojie; Sun, Ying; Chen, Huiyong; Kong, Xiufang; Zhou, Jianjun; Zhou, Yi; Ma, Lili; Jiang, Lindi

    2017-08-01

    Reduction of urate depositions in the joints, on dual-energy computed tomography (DECT), in patients with gout during urate-lowering therapy (ULT) was demonstrated in previous studies. The aim of this study was to further investigate the changes in distribution of urate deposits during ULT. This randomized controlled trial enrolled 46 patients diagnosed with gout from Zhongshan Hospital, China, between October 2013 and June 2014. Epidemiological data, serum uric acid level, and arthritis attacks were recorded at monthly follow-up visits. DECT of bilateral feet and ankles was performed at baseline and after 6 months of ULT. Overall, 163 areas of urate deposition were found in the 46 patients; of these, 133/163 (81.6%) areas were associated with former arthritis attacks. On DECT at 6 months, the number of urate deposits decreased to 126, with 68 areas disappearing and 31 new deposits areas. The mean volume of urate deposits at baseline was 1.3 ± 3.8 cm 3 , decreasing to 0.6 ± 2.1 cm 3 at the end of 6 months (P = 0.01), with 3/46 (6.5%) patients showing complete disappearance of urate deposits. New urate depositions were found in 21/46 (45.7%) patients, while urate depositions in some joints disappeared in some joints in 31/46 (67.4%) patients. High-sensitivity C-reactive protein was significantly lower in patients with new deposits (4.6 ± 9.3 vs. 7.1 ± 7.6 mg/dL; P = 0.01). There is dynamic redistribution of urate depositions in gout patients receiving ULT.

  11. Data on nearshore wave process and surficial beach deposits, central Tamil Nadu coast, India

    Directory of Open Access Journals (Sweden)

    V. Joevivek

    2017-08-01

    Full Text Available The chronicles of nearshore morphology and surficial beach deposits provide valuable information about the nature of the beach condition and the depositional environment. It imparts an understanding about the spatial and temporal relationship of nearshore waves and its influence over the distribution of beach sediments. This article contains data about wave and sediment dynamics of the ten sandy beaches along the central Tamil Nadu coast, India. This present dataset comprises nearshore wave parameters, breaker wave type, beach morphodynamic state, grain size distribution and weight percentage of heavy and light mineral distribution. The dataset will figure out the beach morphology and hydrodynamic condition with respect to the different monsoonal season. This will act as a field reference to realize the coastal dynamics in an open sea condition. The nearshore entities were obtained from the intensive field survey between January 2011 and December 2011, while characteristics of beach sediments are examined by the chemical process in the laboratory environment.

  12. Effect of Post-Deposition Processing on ZnO Thin Films and Devices

    Science.gov (United States)

    Yen, Tingfang; Haungs, Alan; Kim, Sung Jin; Cartwright, Alexander; Anderson, Wayne A.

    2010-05-01

    Post-deposition processing was conducted on ZnO thin films deposited by radio frequency (RF) magnetron sputtering. Rapid thermal annealing (RTA) and ion implantation followed by RTA gave increased conductivity and the latter increased Hall-effect mobility from 1.7 cm2 V-1 s-1 to 9.5 cm2 V-1 s-1 Metal-semiconductor-metal photodetectors (MSM-PDs) had a low dark current, a high ratio of photo to dark current, and a high responsivity of 2.1 A/W. Current transport mechanisms of MSM-PDs with post-annealing exhibited two primary space-charge-limited mechanisms, m > 2 and m film gave one mechanism with m rise and fall times in the range of 12 ns to 29 ns.

  13. Building a Better Capacitor with Thin-Film Atomic Layer Deposition Processing

    Energy Technology Data Exchange (ETDEWEB)

    Pike, Christopher [North Seattle College, WA (United States)

    2015-08-28

    The goal of this research is to determine procedures for creating ultra-high capacity supercapacitors by using nanofabrication techniques and high k-value dielectrics. One way to potentially solve the problem of climate change is to switch the source of energy to a source that doesn’t release many tons of greenhouse gases, gases which cause global warming, into the Earth’s atmosphere. These trap in more heat from the Sun’s solar energy and cause global temperatures to rise. Atomic layer deposition will be used to create a uniform thin-film of dielectric to greatly enhance the abilities of our capacitors and will build them on the nanoscale.

  14. Monte Carlo simulations used to calculate the energy deposited in the coronary artery lumen as a function of iodine concentration and photon energy.

    Science.gov (United States)

    Hocine, Nora; Meignan, Michel; Masset, Hélène

    2018-02-27

    To better understand the risks of cumulative medical X-ray investigations and the possible causal role of contrast agent on the coronary artery wall, the correlation between iodinated contrast media and the increase of energy deposited in the coronary artery lumen as a function of iodine concentration and photon energy is investigated. The calculations of energy deposition have been performed using Monte Carlo (MC) simulation codes, namely PENetration and Energy LOss of Positrons and Electrons (PENELOPE) and Monte Carlo N-Particle eXtended (MCNPX). Exposure of a cylinder phantom, artery and a metal stent (AISI 316L) to several X-ray photon beams were simulated. For the energies used in cardiac imaging the energy deposited in the coronary artery lumen increases with the quantity of iodine. Monte Carlo calculations indicate a strong dependence of the energy enhancement factor (EEF) on photon energy and iodine concentration. The maximum value of EEF is equal to 25; this factor is showed for 83 keV and for 400 mg Iodine/mL. No significant impact of the stent is observed on the absorbed dose in the artery for incident X-ray beams with mean energies of 44, 48, 52 and 55 keV. A strong correlation was shown between the increase in the concentration of iodine and the energy deposited in the coronary artery lumen for the energies used in cardiac imaging and over the energy range between 44 and 55 keV. The data provided by this study could be useful for creating new medical imaging protocols to obtain better diagnostic information with a lower level of radiation exposure.

  15. ERDA programs and objectives: energy conservation in food processing

    Energy Technology Data Exchange (ETDEWEB)

    Towne, E A [ed.

    1977-07-01

    A workshop on energy conservation in the agriculture processing industry sponsored by ERDA in March 1976 resulted in 87 conservation research recommendations to ERDA. These recommendations and their incorporation into ongoing and planned ERDA research and development programs are discussed. Information is included on using food processing wastes, energy conservation in hot processes and waste heat recovery, ERDA responses to specific workshop recommendations on the processing of chemical fertilizers, dairy products, fruits, meats, vegetables, grain, and textiles.

  16. Ionic liquid-based green processes for energy production.

    Science.gov (United States)

    Zhang, Suojiang; Sun, Jian; Zhang, Xiaochun; Xin, Jiayu; Miao, Qingqing; Wang, Jianji

    2014-11-21

    To mitigate the growing pressure on resource depletion and environment degradation, the development of green processes for the production of renewable energy is highly required. As a class of novel and promising media, ionic liquids (ILs) have shown infusive potential applications in energy production. Aiming to offer a critical overview regarding the new challenges and opportunities of ILs for developing green processes of renewable energy, this article emphasises the role of ILs as catalysts, solvents, or electrolytes in three broadly interesting energy production processes from renewable resources, such as CO2 conversion to fuels and fuel additives, biomass pretreatment and conversion to biofuels, as well as solar energy and energy storage. It is expected that this article will stimulate a generation of new ideas and new technologies in IL-based renewable energy production.

  17. Sedimentological characteristics and depositional processes of sediment gravity flows in rift basins: The Palaeogene Dongying and Shahejie formations, Bohai Bay Basin, China

    Science.gov (United States)

    Liu, Lei; Chen, Hongde; Zhong, Yijiang; Wang, Jun; Xu, Changgui; Chen, Anqing; Du, Xiaofeng

    2017-10-01

    Sediment gravity flow deposits are common, particularly in sandy formations, but their origin has been a matter of debate and there is no consensus about the classification of such deposits. However, sediment gravity flow sandstones are economically important and have the potential to meet a growing demand in oil and gas exploration, so there is a drive to better understand them. This study focuses on sediment gravity flow deposits identified from well cores in Palaeogene deposits from the Liaodong Bay Depression in Bohai Bay Basin, China. We classify the sediment gravity flow deposits into eight lithofacies using lithological characteristics, grain size, and sedimentary structures, and interpret the associated depositional processes. Based on the scale, spatial distribution, and contact relationships of sediment gravity flow deposits, we defined six types of lithofacies associations (LAs) that reflect transformation processes and depositional morphology: LA1 (unconfined proximal breccia deposits), LA2 (confined channel deposits), LA3 (braided-channel lobe deposits), LA4 (unconfined lobe deposits), LA5 (distal sheet deposits), and LA6 (non-channelized sheet deposits). Finally, we established three depositional models that reflect the sedimentological characteristics and depositional processes of sediment gravity flow deposits: (1) slope-apron gravel-rich depositional model, which involves cohesive debris flows deposited as LA1 and dilute turbidity currents deposited as LA5; (2) non-channelized surge-like turbidity current depositional model, which mainly comprises sandy slumping, suspended load dominated turbidity currents, and dilute turbidity currents deposited as LA5 and LA6; and (3) channelized subaqueous-fan depositional model, which consists of non-cohesive bedload dominated turbidity currents, suspended load dominated turbidity currents, and dilute turbidity currents deposited as LA2-LA5, originating from sustained extrabasinal turbidity currents

  18. Energy conservation and cost benefits in the dairy processing industry

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-01-01

    Guidance is given on measuring energy consumption in the plant and pinpointing areas where energy-conservation activities can return the most favorable economics. General energy-conservation techniques applicable to most or all segments of the dairy processing industry, including the fluid milk segment, are emphasized. These general techniques include waste heat recovery, improvements in electric motor efficiency, added insulation, refrigeration improvements, upgrading of evaporators, and increases in boiler efficiency. Specific examples are given in which these techniques are applied to dairy processing plants. The potential for energy savings by cogeneration of process steam and electricity in the dairy industry is also discussed. Process changes primarily applicable to specific milk products which have resulted in significant energy cost savings at some facilities or which promise significant contributions in the future are examined. A summary checklist of plant housekeeping measures for energy conservation and guidelines for economic evaluation of conservation alternatives are provided. (MHR)

  19. Nano crystalline high energy milled 5083 Al powder deposited using cold spray

    Energy Technology Data Exchange (ETDEWEB)

    Rokni, M.R., E-mail: mohammadreza.rokni@mines.sdsmt.edu [Department of Materials and Metallurgical Engineering, Advanced Materials Processing Center, South Dakota School of Mines and Technology (SDSM and T), SD (United States); Widener, C.A. [Department of Materials and Metallurgical Engineering, Advanced Materials Processing Center, South Dakota School of Mines and Technology (SDSM and T), SD (United States); Nardi, A.T. [United Technologies Research Center, East Hartford, CT (United States); Champagne, V.K. [U.S. Army Research Laboratory, Weapons and Materials Research Directorate, Aberdeen Proving Ground, MD (United States)

    2014-06-01

    Electron microscopy and nanoindentation are used to investigate the relationship between microstructure and nanohardness of a non-cryomilled, nanocrystalline 5083 Al alloy powder before and after being deposited by cold spray. Microstructural investigations observed the presence of nano grains in the powder microstructure, ranging from 20 to 80 nm and with a typical grain size of 40–50 nm. It was also revealed that the nanocrystalline structure of the powder is retained after cold spraying. As a result, almost no change in nanohardness was indicated between the powder and the particles interior in the cold sprayed layer. However, hardness was substantially higher in some regions in the cold sprayed layer, which was attributed to the particle–particle interfaces or other areas with very small nano grain size. The presence of some un-joined particle remnant lines was also found in the deposition and explained through Critical Velocity Ratio (CVR) of powder particles. Although cold spray is a high deformation process, there is little evidence of dislocations within the nanograins of the cold sprayed layer. The latter observation is rationalized through intragranular dislocation slip and recovery mechanisms.

  20. Biogenic nanomagnetite in the Lebedinskii deposit: Evidence of biochemical processes in the origin of banded iron formation of KMA

    Science.gov (United States)

    Bortnikov, N. S.; Novikov, V. M.; Boeva, N. M.; Zhukhlistov, A. P.; Zhegallo, E. A.; Soboleva, S. V.

    2017-11-01

    For the first time, biogenic nanomagnetite has been detected in banded iron formation of the Lebedinskii deposit of the KMA and has been demonstrated to be a primary mineral. This finding may imply a key role of metabolic processes in primary deposition of divalent iron with formation of trivalent iron minerals, the precursors of banded iron formation of the KMA.

  1. Low energy production processes in manufacturing of silicon solar cells

    Science.gov (United States)

    Kirkpatrick, A. R.

    1976-01-01

    Ion implantation and pulsed energy techniques are being combined for fabrication of silicon solar cells totally under vacuum and at room temperature. Simplified sequences allow very short processing times with small process energy consumption. Economic projections for fully automated production are excellent.

  2. Point-by-point near-field optical energy deposition around plasmonic nanospheres in absorbing media.

    Science.gov (United States)

    Harrison, R K; Ben-Yakar, Adela

    2015-08-01

    Here we investigate the effects of absorbing media on plasmon-enhanced near-field optical energy deposition. We find that increasing absorption by the medium results in increased particle scattering at the expense of particle absorption, and that much of this increased particle scattering is absorbed by the medium close to the particle surface. We present an analytical method for evaluating the spatial distribution of near-field enhanced absorption surrounding plasmonic metal nanospheres in absorbing media using a new point-by-point method. We propose criteria to define relevant near-field boundaries and calculate the properties of the local absorption enhancement, which redistributes absorption to the near-field and decays asymptotically as a function of the distance from the particle to background levels. Using this method, we performed a large-scale parametric study to understand the effect of particle size and wavelength on the near-field absorption for gold nanoparticles in aqueous media and silicon, and identified conditions that are relevant to enhanced local infrared absorption in silicon. The presented approach provides insight into the local energy transfer around plasmonic nanoparticles for predicting near-field effects for advanced concepts in optical sensing, thin-film solar cells, nonlinear imaging, and photochemical applications.

  3. Transport and spatial energy deposition of relativistic electrons in copper-doped fast ignition plasmas

    Science.gov (United States)

    Jarrott, L. C.; McGuffey, C.; Beg, F. N.; Solodov, A. A.; Theobald, W.; Qiao, B.; Stoeckl, C.; Betti, R.; Chen, H.; Delettrez, J.; Döppner, T.; Giraldez, E. M.; Glebov, V. Y.; Habara, H.; Iwawaki, T.; Key, M. H.; Luo, R. W.; Marshall, F. J.; McLean, H. S.; Mileham, C.; Patel, P. K.; Santos, J. J.; Sawada, H.; Stephens, R. B.; Yabuuchi, T.; Wei, M. S.

    2017-10-01

    Fast electron transport and spatial energy deposition are investigated in integrated cone-guided Fast Ignition experiments by measuring fast electron induced copper K-shell emission using a copper tracer added to deuterated plastic shells with a geometrically reentrant gold cone. Experiments were carried out at the Laboratory for Laser Energetics on the OMEGA/OMEGA-EP Laser where the plastic shells were imploded using 54 of the 60 OMEGA60 beams (3ω, 20 kJ), while the high intensity OMEGA-EP (BL2) beam (1 ω, 10 ps, 500 J, Ipeak > 1019 W/cm2) was focused onto the inner cone tip. A retrograde analysis using the hybrid-PIC electron transport code, ZUMA, is performed to examine the sensitivity of the copper Kα spatial profile on the laser-produced fast electrons, facilitating the optimization of new target point designs and laser configurations to improve the compressed core areal density by a factor of 4 and the fast electron energy coupling by a factor of 3.5.

  4. Reconstructing the energy band electronic structure of pulsed laser deposited CZTS thin films intended for solar cell absorber applications

    Energy Technology Data Exchange (ETDEWEB)

    Pandiyan, Rajesh [Institut National de la Recherche Scientifique, Centre-Énergie, Matériaux et Télécommunications, 1650 Blvd. Lionel–Boulet, C.P. 1020, Varennes, QC J3X-1S2 (Canada); Oulad Elhmaidi, Zakaria [Institut National de la Recherche Scientifique, Centre-Énergie, Matériaux et Télécommunications, 1650 Blvd. Lionel–Boulet, C.P. 1020, Varennes, QC J3X-1S2 (Canada); University of Mohammed V, Faculty of Sciences, Materials Physics Laboratory, B.P. 1014 Rabat (Morocco); Sekkat, Zouheir [Optics & Photonics Center, Moroccan Foundation for Advanced Science, Innovation and Research, Rabat (Morocco); Abd-lefdil, Mohammed [University of Mohammed V, Faculty of Sciences, Materials Physics Laboratory, B.P. 1014 Rabat (Morocco); El Khakani, My Ali, E-mail: elkhakani@emt.inrs.ca [Institut National de la Recherche Scientifique, Centre-Énergie, Matériaux et Télécommunications, 1650 Blvd. Lionel–Boulet, C.P. 1020, Varennes, QC J3X-1S2 (Canada)

    2017-02-28

    Highlights: • High quality CZTS thin films grown by means of PLD technique without resorting to any post sulfurization process. • Effect of thermal annealing treatments (in the 200–500 °C range) on the structural, morphological and optoelectronic properties of PLD-CZTS films. • Experimental determination of key optoelectronic parameters (i.e.; E{sub g}, VBM, ϕ, I{sub p}, and χ) enabling the reconstruction of energy band electronic structure of the PLD-CZTS films. • Investigation on the energy band alignments of the heterojunction interface formed between CZTS and both CdS and ZnS buffer layer materials. - Abstract: We report here on the use of pulsed KrF-laser deposition (PLD) technique for the growth of high-quality Cu{sub 2}ZnSnS{sub 4} (CZTS) thin films onto Si, and glass substrates without resorting to any post sulfurization process. The PLD-CZTS films were deposited at room temperature (RT) and then subjected to post annealing at different temperatures ranging from 200 to 500 °C in Argon atmosphere. The X-ray diffraction and Raman spectroscopy confirmed that the PLD films crystallize in the characteristic kesterite CZTS structure regardless of their annealing temperature (T{sub a}), but their crystallinity is much improved for T{sub a} ≥ 400 °C. The PLD-CZTS films were found to exhibit a relatively dense morphology with a surface roughness (RMS) that increases with T{sub a} (from ∼14 nm at RT to 70 nm at T{sub a} = 500 °C with a value around 40 nm for T{sub a} = 300–400 °C). The optical bandgap of the PLD-CZTS films, was derived from UV–vis transmission spectra analysis, and found to decrease from 1.73 eV for non-annealed films to ∼1.58 eV for those annealed at T{sub a} = 300 °C. These band gap values are very close to the optimum value needed for an ideal solar cell absorber. In order to achieve a complete reconstruction of the one-dimensional energy band structure of these PLD-CZTS absorbers, we have combined both XPS and UPS

  5. Evaluation of energy deposition and secondary particle production in proton therapy of brain using a slab head phantom.

    Science.gov (United States)

    Jia, Sayyed Bijan; Hadizadeh, Mohammad Hadi; Mowlavi, Ali Asghar; Loushab, Mahdy Ebrahimi

    2014-11-01

    Evaluation of energy deposition of protons in human brain and calculation of the secondary neutrons and photons produced by protons in proton therapy. Radiation therapy is one of the main methods of treating localized cancer tumors. The use of high energy proton beam in radiotherapy was proposed almost 60 years ago. In recent years, there has been a revival of interest in this subject in the context of radiation therapy. High energy protons suffer little angular deflection and have a well-defined penetration range, with a sharp increase in the energy loss at the end of their trajectories, namely the Bragg peak. A slab head phantom was used for the purpose of simulating proton therapy in brain tissue. In this study simulation was carried out using the Monte Carlo MCNPX code. By using mono energetic proton pencil beams, energy depositions in tissues, especially inside the brain, as well as estimating the neutron and photon production as a result of proton interactions in the body, together with their energy spectra, were calculated or obtained. The amount of energy escaped from the head by secondary neutrons and photons was determined. It was found that for high energy proton beams the amount of escaped energy by neutrons is almost 10 times larger than that by photons. We estimated that at 110 MeV beam energy, the overall proton energy "leaked" from the head by secondary photons and neutrons to be around 1%.

  6. Half-sandwich cobalt complexes in the metal-organic chemical vapor deposition process

    Energy Technology Data Exchange (ETDEWEB)

    Georgi, Colin [Technische Universität Chemnitz, Faculty of Natural Science, Institute of Chemistry, Inorganic Chemistry, Chemnitz 09107 (Germany); Hapke, Marko; Thiel, Indre [Leibniz-Institut für Katalyse e.V. an der Universität Rostock (LIKAT), Albert-Einstein-Straße 29a, Rostock 18059 (Germany); Hildebrandt, Alexander [Technische Universität Chemnitz, Faculty of Natural Science, Institute of Chemistry, Inorganic Chemistry, Chemnitz 09107 (Germany); Waechtler, Thomas; Schulz, Stefan E. [Fraunhofer Institute of Electronic Nano Systems (ENAS), Technologie-Campus 3, Chemnitz 09126 (Germany); Technische Universität Chemnitz, Center for Microtechnologies (ZfM), Chemnitz 09107 (Germany); Lang, Heinrich, E-mail: heinrich.lang@chemie.tu-chemnitz.de [Technische Universität Chemnitz, Faculty of Natural Science, Institute of Chemistry, Inorganic Chemistry, Chemnitz 09107 (Germany)

    2015-03-02

    A series of cobalt half-sandwich complexes of type [Co(η{sup 5}-C{sub 5}H{sub 5})(L)(L′)] (1: L, L′ = 1,5-hexadiene; 2: L = P(OEt){sub 3}, L′ = H{sub 2}C=CHSiMe{sub 3}; 3: L = L′ = P(OEt){sub 3}) has been studied regarding their physical properties such as the vapor pressure, decomposition temperature and applicability within the metal-organic chemical vapor deposition (MOCVD) process, with a focus of the influence of the phosphite ligands. It could be shown that an increasing number of P(OEt){sub 3} ligands increases the vapor pressure and thermal stability of the respective organometallic compound. Complex 3 appeared to be a promising MOCVD precursor with a high vapor pressure and hence was deposited onto Si/SiO{sub 2} (100 nm) substrates. The resulting reflective layer is closed, dense and homogeneous, with a slightly granulated surface morphology. X-ray photoelectron spectroscopy (XPS) studies demonstrated the formation of metallic cobalt, cobalt phosphate, cobalt oxide and cobalt carbide. - Highlights: • Thermal studies and vapor pressure measurements of cobalt half-sandwich complexes was carried out. • Chemical vapor deposition with cobalt half-sandwich complexes is reported. • The use of Co-phosphites results in significant phosphorous-doped metallic layers.

  7. Reconstructing depositional processes and history from reservoir stratigraphy: Englebright Lake, Yuba River, northern California

    Science.gov (United States)

    Snyder, Noah P.; Wright, Scott A.; Alpers, Charles N.; Flint, Lorraine E.; Holmes, Charles W.; Rubin, David M.

    2006-12-01

    Reservoirs provide the opportunity to link watershed history with its stratigraphic record. We analyze sediment cores from a northern California reservoir in the context of hydrologic history, watershed management, and depositional processes. Observations of recent depositional patterns, sediment-transport calculations, and 137Cs geochronology support a conceptual model in which the reservoir delta progrades during floods of short duration (days) and is modified during prolonged (weeks to months) drawdowns that rework topset beds and transport sand from topsets to foresets. Sediment coarser than 0.25-0.5 mm deposits in foresets and topsets, and finer material falls out of suspension as bottomset beds. Simple hydraulic calculations indicate that fine sand (0.063-0.5 mm) is transported into the distal bottomset area only during floods. The overall stratigraphy suggests that two phases of delta building occurred in the reservoir. The first, from dam construction in 1940 to 1970, was heavily influenced by annual, prolonged >20 m drawdowns of the water level. The second, built on top of the first, reflects sedimentation from 1970 to 2002 when the influence of drawdowns was less. Sedimentation rates in the central part of the reservoir have declined ˜25% since 1970, likely reflecting a combination of fewer large floods, changes in watershed management, and winnowing of stored hydraulic mining sediment.

  8. Transport phenomena in the close-spaced sublimation deposition process for manufacture of large-area cadmium telluride photovoltaic panels: Modeling and optimization

    Science.gov (United States)

    Malhotra, C. P.

    With increasing national and global demand for energy and concerns about the effect of fossil fuels on global climate change, there is an increasing emphasis on the development and use of renewable sources of energy. Solar cells or photovoltaics constitute an important renewable energy technology but the major impediment to their widespread adoption has been their high initial cost. Although thin-film photovoltaic semiconductors such as cadmium sulfide-cadmium telluride (CdS/CdTe) can potentially be inexpensively manufactured using large area deposition techniques such as close-spaced sublimation (CSS), their low stability has prevented them from becoming an alternative to traditional polycrystalline silicon solar cells. A key factor affecting the stability of CdS/CdTe cells is the uniformity of deposition of the thin films. Currently no models exist that can relate the processing parameters in a CSS setup with the film deposition uniformity. Central to the development of these models is a fundamental understanding of the complex transport phenomena which constitute the deposition process which include coupled conduction and radiation as well as transition regime rarefied gas flow. This thesis is aimed at filling these knowledge gaps and thereby leading to the development of the relevant models. The specific process under consideration is the CSS setup developed by the Materials Engineering Group at the Colorado State University (CSU). Initially, a 3-D radiation-conduction model of a single processing station was developed using the commercial finite-element software ABAQUS and validated against data from steady-state experiments carried out at CSU. A simplified model was then optimized for maximizing the steady-state thermal uniformity within the substrate. It was inferred that contrary to traditional top and bottom infrared lamp heating, a lamp configuration that directs heat from the periphery of the sources towards the center results in the minimum temperature

  9. Characterization of hydroxyapatite coating by pulse laser deposition technique on stainless steel 316 L by varying laser energy

    Energy Technology Data Exchange (ETDEWEB)

    Khandelwal, Himanshu, E-mail: khandelwal_iit@yahoo.com [IIT Bombay, Mumbai, Maharashtra (India); Singh, Gurbhinder, E-mail: gurbinder@yahoo.com [Bhai Maha Singh College of Engineering, Muktsar, Panjab (India); Agrawal, Khelendra [Apex Institute of Engineering, Jaipur (India); Prakash, Satya; Agarwal, R.D. [IIT Roorkee (India)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Hydroxyapatite coating was successfully deposited on stainless steel substrate by pulse laser deposition at different energy levels (i.e. 300 mJ and 500 mJ, respectively). Black-Right-Pointing-Pointer Variation in laser energy affects the surface characteristic of hydroxyapatite coating (particle size, surface roughness, uniformity, Ca/P ratio). Black-Right-Pointing-Pointer Laser energy between 300 mJ and 500 mJ is the optimal choice for obtaining ideal Ca/P ratio. - Abstract: Hydroxyapatite is an attractive biomaterial mainly used in bone and tooth implants because it closely resembles human tooth and bone mineral and has proven to be biologically compatible with these tissues. In spite of this advantage of hydroxyapatite it has also certain limitation like inferior mechanical properties which do not make it suitable for long term load bearing applications; hence a lot of research is going on in the development of hydroxyapatite coating over various metallic implants. These metallic implants have good biocompatibility and mechanical properties. The aim of the present work is to deposit hydroxyapatite coating over stainless steel grade 316 L by pulse laser deposition technique by varying laser energy. To know the effect of this variation, the coatings were than characterized in detail by X-ray diffraction, finite emission-scanning electron microscope, atomic force microscope and energy dispersive X-ray spectroscopy.

  10. Energy-Intensive Processes Portfolio: Addressing Key Energy Challenges Across U.S. Industry

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-03-07

    AMO is developing advanced technologies that cut energy use and carbon emissions in some of the most energy-intensive processes within U.S. manufacturing. The brochure describes the AMO R&D projects that address these challenges.

  11. Impact of hydrotalcite deposition on biogeochemical processes in a shallow tropical bay.

    Science.gov (United States)

    Alongi, Daniel M; McKinnon, A David

    2011-03-01

    The biogeochemistry of a tropical shoal bay (Melville Bay, Australia) impacted by the effluent release, precipitation, and deposition of hydrotalcite from an alumina refinery was studied in both wet and dry seasons. Within the deposition zone, sulfate reduction dominated benthic carbon cycling accounting for ≈100% of total microbial activity, with rates greater than those measured in most other marine sediments. These rapid rates of anoxic metabolism resulted in high rates of sulfide and ammonium production and low C:S ratios, implying significant preservation of S in stable sulfide minerals. Rates of total microbial activity were significantly less in control sediments of equivalent grain size, where sulfate reduction accounted for ≈50% of total benthic metabolism. Rates of planktonic carbon cycling overlying the deposition zone were also greater than those measured in the control areas of southern Melville Bay. At the sediment surface, productive algal and cyanobacterial mats helped stabilize the sediment surface and oxidize sulfide to sulfate to maintain a fully oxygenated water-column overlying the impacted zone. The mats utilized a significant fraction of dissolved inorganic N and P released from the sea bed; some nutrients escaped to the water-column such that benthic regeneration of NH₄+ and PO₄³⁻ accounted for 100% and 42% of phytoplankton requirements for N and P, respectively. These percentages are high compared to other tropical coastal environments and indicate that benthic nutrient recycling may be a significant factor driving water-column production overlying the deposition zone. With regard to remediation, it is recommended that the sea bed not be disturbed as attempts at removal may result in further environmental problems and would require specific assessment of the proposed removal process. Copyright © 2010 Elsevier Ltd. All rights reserved.

  12. Mechanistic modeling study on process optimization and precursor utilization with atmospheric spatial atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Deng, Zhang; He, Wenjie; Duan, Chenlong [State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Chen, Rong, E-mail: rongchen@mail.hust.edu.cn [State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China); Shan, Bin [State Key Laboratory of Material Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan, Hubei 430074 (China)

    2016-01-15

    Spatial atomic layer deposition (SALD) is a promising technology with the aim of combining the advantages of excellent uniformity and conformity of temporal atomic layer deposition (ALD), and an industrial scalable and continuous process. In this manuscript, an experimental and numerical combined model of atmospheric SALD system is presented. To establish the connection between the process parameters and the growth efficiency, a quantitative model on reactant isolation, throughput, and precursor utilization is performed based on the separation gas flow rate, carrier gas flow rate, and precursor mass fraction. The simulation results based on this model show an inverse relation between the precursor usage and the carrier gas flow rate. With the constant carrier gas flow, the relationship of precursor usage and precursor mass fraction follows monotonic function. The precursor concentration, regardless of gas velocity, is the determinant factor of the minimal residual time. The narrow gap between precursor injecting heads and the substrate surface in general SALD system leads to a low Péclet number. In this situation, the gas diffusion act as a leading role in the precursor transport in the small gap rather than the convection. Fluid kinetics from the numerical model is independent of the specific structure, which is instructive for the SALD geometry design as well as its process optimization.

  13. A Complete Reporting of MCNP6 Validation Results for Electron Energy Deposition in Single-Layer Extended Media for Source Energies <= 1-MeV

    Energy Technology Data Exchange (ETDEWEB)

    Dixon, David A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hughes, Henry Grady [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-04

    In this paper, we expand on previous validation work by Dixon and Hughes. That is, we present a more complete suite of validation results with respect to to the well-known Lockwood energy deposition experiment. Lockwood et al. measured energy deposition in materials including beryllium, carbon, aluminum, iron, copper, molybdenum, tantalum, and uranium, for both single- and multi-layer 1-D geometries. Source configurations included mono-energetic, mono-directional electron beams with energies of 0.05-MeV, 0.1-MeV, 0.3- MeV, 0.5-MeV, and 1-MeV, in both normal and off-normal angles of incidence. These experiments are particularly valuable for validating electron transport codes, because they are closely represented by simulating pencil beams incident on 1-D semi-infinite slabs with and without material interfaces. Herein, we include total energy deposition and energy deposition profiles for the single-layer experiments reported by Lockwood et al. (a more complete multi-layer validation will follow in another report).

  14. Cell to Cell Variability of Radiation-Induced Foci: Relation between Observed Damage and Energy Deposition.

    Directory of Open Access Journals (Sweden)

    Gaëtan Gruel

    Full Text Available Most studies that aim to understand the interactions between different types of photon radiation and cellular DNA assume homogeneous cell irradiation, with all cells receiving the same amount of energy. The level of DNA damage is therefore generally determined by averaging it over the entire population of exposed cells. However, evaluating the molecular consequences of a stochastic phenomenon such as energy deposition of ionizing radiation by measuring only an average effect may not be sufficient for understanding some aspects of the cellular response to this radiation. The variance among the cells associated with this average effect may also be important for the behaviour of irradiated tissue. In this study, we accurately estimated the distribution of the number of radiation-induced γH2AX foci (RIF per cell nucleus in a large population of endothelial cells exposed to 3 macroscopic doses of gamma rays from 60Co. The number of RIF varied significantly and reproducibly from cell to cell, with its relative standard deviation ranging from 36% to 18% depending on the macroscopic dose delivered. Interestingly, this relative cell-to-cell variability increased as the dose decreased, contrary to the mean RIF count per cell. This result shows that the dose effect, in terms of the number of DNA lesions indicated by RIF is not as simple as a purely proportional relation in which relative SD is constant with dose. To analyse the origins of this observed variability, we calculated the spread of the specific energy distribution for the different target volumes and subvolumes in which RIF can be generated. Variances, standard deviations and relative standard deviations all changed similarly from dose to dose for biological and calculated microdosimetric values. This similarity is an important argument that supports the hypothesis of the conservation of the association between the number of RIF per nucleus and the specific energy per DNA molecule. This

  15. Energy deposition of multi-MeV protons in compressed targets of fast-ignition inertial confinement fusion.

    Science.gov (United States)

    Mahdavi, M; Koohrokhi, T

    2012-01-01

    The energy loss and penetration of multi-megelectronvolt protons into a uniform deuterium-tritium (DT) plasma has been calculated. The effects of nuclear elastic scattering and Coulomb interactions are treated from a unified point of view. In general, multiple scattering enhances the proton linear-energy transfer along the initial proton direction, thus the energy deposition increases near the end of its range. The net effect of multiple scattering is to reduce the penetration from 1.20 to 1.02 g cm-2 for 12 MeV protons in a ρ=500 g cm-3 plasma at T=5 keV. These results should have relevance to proton fast ignition, specifically to energy deposition calculations that critically assess quantitative ignition requirements.

  16. Particle engineering in pharmaceutical solids processing: surface energy considerations.

    Science.gov (United States)

    Williams, Daryl R

    2015-01-01

    During the past 10 years particle engineering in the pharmaceutical industry has become a topic of increasing importance. Engineers and pharmacists need to understand and control a range of key unit manufacturing operations such as milling, granulation, crystallisation, powder mixing and dry powder inhaled drugs which can be very challenging. It has now become very clear that in many of these particle processing operations, the surface energy of the starting, intermediate or final products is a key factor in understanding the processing operation and or the final product performance. This review will consider the surface energy and surface energy heterogeneity of crystalline solids, methods for the measurement of surface energy, effects of milling on powder surface energy, adhesion and cohesion on powder mixtures, crystal habits and surface energy, surface energy and powder granulation processes, performance of DPI systems and finally crystallisation conditions and surface energy. This review will conclude that the importance of surface energy as a significant factor in understanding the performance of many particulate pharmaceutical products and processes has now been clearly established. It is still nevertheless, work in progress both in terms of development of methods and establishing the limits for when surface energy is the key variable of relevance.

  17. Dynamic Modelling of Erosion and Deposition Processes in Debris Flows With Application to Real Debris Flow Events in Switzerland

    Science.gov (United States)

    Deubelbeiss, Y.; McArdell, B. W.; Graf, C.

    2011-12-01

    The dynamics of a debris flow can be significantly influenced by erosion and deposition processes during an event because volume changes have a strong influence on flow properties such as flow velocity, flow heights and runout distances. It is therefore worth exploring how to include these processes in numerical models, which are used for hazard assessment and mitigation measure planning. However, it is still under debate, what mechanism drives the erosion of material at the base of a debris flow. There are different processes attributed to erosion: it has been proposed that erosion correlates with the stresses due to granular interactions at the front, which in turn strongly depend on particle size or it may be related to basal shear forces. Because it is expected that larger flow heights result in larger stresses one can additionally hypothesize that there is a correlation between erosion rate and flow height. To test different erosion laws in a numerical model and its influence on the flow behavior we implement different relationships and compare simulation results with field data. Herefore, we use the numerical model, RAMMS (Christen et al., 2010), employing the Voellmy-fluid friction law. While it has already been shown that a correlation of erosion with velocity does not lead to a satisfying result (too high entrainment in the tail) a correlation with flow height combined with velocity (momentum) has been successfully applied to ice-avalanches. Currently, we are testing the momentum-driven and for comparison we reconsider the simple velocity-driven erosion rate. However, these laws do not consider processes on a smaller scale such as particle fluctuations resulting in energy production, which might play an important role. Therefore, we additionally consider an erosion model that has potential to draw new insights on the erosion process in debris flows. The model is based on an extended Voellmy model, which additionally employs an equation, which is a measure

  18. Spin structure in high energy processes

    Science.gov (United States)

    Deporcel, L.; Dunwoodie, C.

    1994-12-01

    This report contains papers of the following topics: Spin, Mass, and Symmetry; physics with polarized Z(sup 0)s; spin and precision electroweak physics; polarized electron sources; polarization phenomena in quantum chromodynamics; polarized lepton-nucleon scattering; polarized targets in high energy physics; spin dynamics in storage rings and linear accelerators; spin formalism and applications to new physics searches; precision electroweak physics at LEP; recent results on heavy flavor physics from LEP experiments using 1990--1992 data; precise measurement of the left-right cross section asymmetry in Z boson production by electron-positron collisions; preliminary results on heavy flavor physics at SLD; QCD tests with SLD and polarized beams; recent results from TRISTAN at KEK; recent B physics results from CLEO; searching for the H dibaryon at Brookhaven; recent results from the compton observatory; the spin structure of the deuteron; spin structure of the neutron ((sup 3)HE) and the Bjoerken sum rule; a consumer's guide to lattice QCD results; top ten models constrained by b yields sy; a review of the Fermilab fixed target program; results from the D0 experiment; results from CDF at FNAL; quantum-mechanical suppression of bremsstrahlung; report from the ZEUS collaboration at HERA; physics from the first year of H1 at HERA, and hard diffraction. These papers have been cataloged separately elsewhere.

  19. Spin structure in high energy processes: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    DePorcel, L.; Dunwoodie, C. [eds.

    1994-12-01

    This report contains papers as the following topics: Spin, Mass, and Symmetry; physics with polarized Z{sup 0}s; spin and precision electroweak physics; polarized electron sources; polarization phenomena in quantum chromodynamics; polarized lepton-nucleon scattering; polarized targets in high energy physics; spin dynamics in storage rings and linear accelerators; spin formalism and applications to new physics searches; precision electroweak physics at LEP; recent results on heavy flavor physics from LEP experiments using 1990--1992 data; precise measurement of the left-right cross section asymmetry in Z boson production by electron-positron collisions; preliminary results on heavy flavor physics at SLD; QCD tests with SLD and polarized beams; recent results from TRISTAN at KEK; recent B physics results from CLEO; searching for the H dibaryon at Brookhaven; recent results from the compton observatory; the spin structure of the deuteron; spin structure of the neutron ({sup 3}HE) and the Bjoerken sum rule; a consumer`s guide to lattice QCD results; top ten models constrained by b {yields} sy; a review of the Fermilab fixed target program; results from the D0 experiment; results from CDF at FNAL; quantum-mechanical suppression of bremsstrahlung; report from the ZEUS collaboration at HERA; physics from the first year of H1 at HERA, and hard diffraction. These papers have been cataloged separately elsewhere.

  20. Electromagnetic sensors for monitoring of scour and deposition processes at bridges and offshore wind turbines

    Science.gov (United States)

    Michalis, Panagiotis; Tarantino, Alessandro; Judd, Martin

    2014-05-01

    Recent increases in precipitation have resulted in severe and frequent flooding incidents. This has put hydraulic structures at high risk of failure due to scour, with severe consequences to public safety and significant economic losses. Foundation scour is the leading cause of bridge failures and one of the main climate change impacts to highway and railway infrastructure. Scour action is also being considered as a major risk for offshore wind farm developments as it leads to excessive excavation of the surrounding seabed. Bed level conditions at underwater foundations are very difficult to evaluate, considering that scour holes are often re-filled by deposited loose material which is easily eroded during smaller scale events. An ability to gather information concerning the evolution of scouring will enable the validation of models derived from laboratory-based studies and the assessment of different engineering designs. Several efforts have focused on the development of instrumentation techniques to measure scour processes at foundations. However, they are not being used routinely due to numerous technical and cost issues; therefore, scour continues to be inspected visually. This research project presents a new sensing technique, designed to measure scour depth variation and sediment deposition around the foundations of bridges and offshore wind turbines, and to provide an early warning of an impending structural failure. The monitoring system consists of a probe with integrated electromagnetic sensors, designed to detect the change in the surrounding medium around the foundation structure. The probe is linked to a wireless network to enable remote data acquisition. A developed prototype and a commercial sensor were evaluated to quantify their capabilities to detect scour and sediment deposition processes. Finite element modelling was performed to define the optimum geometric characteristics of the prototype scour sensor based on models with various permittivity

  1. Nanostructured bioactive glass-ceramic coatings deposited by the liquid precursor plasma spraying process

    Energy Technology Data Exchange (ETDEWEB)

    Xiao Yanfeng; Song Lei; Liu Xiaoguang; Huang Yi; Huang Tao; Wu Yao; Chen Jiyong [National Engineering Research Center for Biomaterials, Sichuan University, 29 Wangjiang Road Chengdu, Sichuan 610064 (China); Wu Fang, E-mail: fwu@scu.edu.cn [National Engineering Research Center for Biomaterials, Sichuan University, 29 Wangjiang Road Chengdu, Sichuan 610064 (China)

    2011-01-01

    Bioactive glass-ceramic coatings have great potential in dental and orthopedic medical implant applications, due to its excellent bioactivity, biocompatibility and osteoinductivity. However, most of the coating preparation techniques either produce only thin thickness coatings or require tedious preparation steps. In this study, a new attempt was made to deposit bioactive glass-ceramic coatings on titanium substrates by the liquid precursor plasma spraying (LPPS) process. Tetraethyl orthosilicate, triethyl phosphate, calcium nitrate and sodium nitrate solutions were mixed together to form a suspension after hydrolysis, and the liquid suspension was used as the feedstock for plasma spraying of P{sub 2}O{sub 5}-Na{sub 2}O-CaO-SiO{sub 2} bioactive glass-ceramic coatings. The in vitro bioactivities of the as-deposited coatings were evaluated by soaking the samples in simulated body fluid (SBF) for 4 h, 1, 2, 4, 7, 14, and 21 days, respectively. The as-deposited coating and its microstructure evolution behavior under SBF soaking were systematically analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma (ICP), and Fourier transform infrared (FTIR) spectroscopy. The results showed that P{sub 2}O{sub 5}-Na{sub 2}O-CaO-SiO{sub 2} bioactive glass-ceramic coatings with nanostructure had been successfully synthesized by the LPPS technique and the synthesized coatings showed quick formation of a nanostructured HCA layer after being soaked in SBF. Overall, our results indicate that the LPPS process is an effective and simple method to synthesize nanostructured bioactive glass-ceramic coatings with good in vitro bioactivity.

  2. NMR metabolomics to study the regulation of energy metabolism on chicken lines divergent for low or high abdominal fat deposition

    OpenAIRE

    Lalande, Julie,; Gondret, Florence; Louveau, Isabelle; Tea, Illa,; Duclos, Michel; Baeza, Elisabeth

    2013-01-01

    NMR metabolomics is suitable for studying the regulation of energy metabolism on chicken lines divergent for low or high abdominal fat deposition. It is shown that plasma metabolic profiles are different in chickens fed with high and low fat diets. New information are thus obtained on circulating nutrients, which may help in elucidating key regulators associated to variations in body fat content.

  3. Design and Operation of an Optically-Accessible Modular Reactor for Diagnostics of Thermal Thin Film Deposition Processes.

    Science.gov (United States)

    Kimes, W A; Sperling, B A; Maslars, J E

    2015-01-01

    The design and operation of a simple, optically-accessible modular reactor for probing thermal thin film deposition processes, such as atomic layer deposition processes (ALD) and chemical vapor deposition (CVD), is described. This reactor has a nominal footprint of 225 cm(2) and a mass of approximately 6.6 kg, making it small enough to conveniently function as a modular component of an optical train. The design is simple, making fabrication straightforward and relatively inexpensive. Reactor operation is characterized using two infrared absorption measurements to determine exhaust times for tetrakis(dimethylamino)titanium and water, proto-typical ALD precursors, in a pressure and flow regime commonly used for ALD.

  4. Modeling and optimization of atomic layer deposition processes on vertically aligned carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Nuri Yazdani

    2014-03-01

    Full Text Available Many energy conversion and storage devices exploit structured ceramics with large interfacial surface areas. Vertically aligned carbon nanotube (VACNT arrays have emerged as possible scaffolds to support large surface area ceramic layers. However, obtaining conformal and uniform coatings of ceramics on structures with high aspect ratio morphologies is non-trivial, even with atomic layer deposition (ALD. Here we implement a diffusion model to investigate the effect of the ALD parameters on coating kinetics and use it to develop a guideline for achieving conformal and uniform thickness coatings throughout the depth of ultra-high aspect ratio structures. We validate the model predictions with experimental data from ALD coatings of VACNT arrays. However, the approach can be applied to predict film conformality as a function of depth for any porous topology, including nanopores and nanowire arrays.

  5. Solar Energy Supported Desalination Processes for Desalting of Sea Water

    OpenAIRE

    , M.E. Argun

    2010-01-01

    This study is a review of solar energy supported desalination processes. Although the sun light captured by earth excessively meets of world’s need, we can use a few amount of this source. Solar energy supported desalination is one of the method developed for desalination. Solar energy usage will also decrease CO2 emission which is responsible of global warming. A lot of studies to improve the efficiency of solar energy systems have been carried out during last years. Solar energy can be used...

  6. Complex processing of rubber waste through energy recovery

    Directory of Open Access Journals (Sweden)

    Roman Smelík

    2015-12-01

    Full Text Available This article deals with the applied energy recovery solutions for complex processing of rubber waste for energy recovery. It deals specifically with the solution that could maximize possible use of all rubber waste and does not create no additional waste that disposal would be expensive and dangerous for the environment. The project is economically viable and energy self-sufficient. The outputs of the process could replace natural gas and crude oil products. The other part of the process is also the separation of metals, which can be returned to the metallurgical secondary production.

  7. Transformation of cadmium hydroxide to cadmium oxide thin films synthesized by SILAR deposition process: Role of varying deposition cycles

    Directory of Open Access Journals (Sweden)

    A.C. Nwanya

    2016-06-01

    Full Text Available Successive Ionic Layer Adsorption and Reaction (SILAR was used to deposit nanocrystalline cadmium oxide (CdO thin films on microscopic glass substrates for various cycles (40–120. This is based on alternate dipping of the substrate in CdCl2 solution made alkaline (pH ∼12 with NaOH, rinsing with distilled water, followed by air treatment with air dryer and annealing at 300 °C for 1 h in air. The prepared films were characterized by X-ray diffraction (XRD, UV–Visible Spectrophotomer (UV–Vis and Scanning Electron Microscopy (SEM. The 80th cycle was observed to be the saturation stage for this reaction. The XRD results confirmed the films to be CdO with some Cd(OH2 phase at higher deposition cycles. The films were polycrystalline in nature having high orientation along (111 and (200 planes. As the number of cycles increases the calculated average crystallite sizes increase gradually up till the 80th cycle after which a gradual decrease in the crystallite size was observed with increasing number of cycles. The films’ transmittance in the visible and near infrared region decreased as the number of cycles increased and ranged between 25 and 80%. This work shows the feasibility of using simple SILAR method at room temperature to obtain Cd(OH2 films which are transformed to CdO thin films after annealing.

  8. Use of beam deflection to control an electron beam wire deposition process

    Science.gov (United States)

    Taminger, Karen M. (Inventor); Hofmeister, William H. (Inventor); Hafley, Robert A. (Inventor)

    2013-01-01

    A method for controlling an electron beam process wherein a wire is melted and deposited on a substrate as a molten pool comprises generating the electron beam with a complex raster pattern, and directing the beam onto an outer surface of the wire to thereby control a location of the wire with respect to the molten pool. Directing the beam selectively heats the outer surface of the wire and maintains the position of the wire with respect to the molten pool. An apparatus for controlling an electron beam process includes a beam gun adapted for generating the electron beam, and a controller adapted for providing the electron beam with a complex raster pattern and for directing the electron beam onto an outer surface of the wire to control a location of the wire with respect to the molten pool.

  9. Electro-deposition painting process improvement of cab truck by Six Sigma concept

    Science.gov (United States)

    Kawitu, Kitiya; Chutima, Parames

    2017-06-01

    The case study company is a manufacturer of trucks and currently facing a high rework cost due to the thickness of the electro-deposited paint (EDP) of the truck cab is lower than standard. In addition, the process capability is very low. The Six Sigma concept consisting of 5 phases (DMAIC) is applied to determine new parameter settings for each significant controllable factor. After the improvement, EDP thickness of the truck cab increases from 17.88μ to 20μ (i.e. standard = 20 ± 3μ). Moreover, the process capability indexes (Cp and Cpk) are increased from 0.9 to 1.43, and from 0.27 to 1.43, respectively. This improvement could save the rework cost about 1.6M THB per year.

  10. Characterisation of TiC layers deposited using an electrical discharge coating process

    Science.gov (United States)

    Algodi, S. J.; Murray, J. W.; Clare, A. T.; Brown, P. D.

    2015-10-01

    Electrical discharge machining (EDM) is a non-conventional, high-accuracy machining process for the manufacture of complex shapes, regardless of hardness of the workpiece. There is interest to develop the EDM technique for coating or surface modification by using a powder metallurgy (PM) tool electrode and/or added powder suspended within the dielectric fluid. We report on the EDM deposition of TiC coatings onto stainless steel, using either Cu or TiC electrodes, with and without Ti powder in the working oil. EDM processed layers exhibited hardness values ∼ 3-4 times higher than the substrate, emphasising the ability of EDM to impart improved mechanical performance to the surface of austenitic stainless steel.

  11. Silicon Chemical Vapor Deposition Process Using a Half-Inch Silicon Wafer for Minimal Manufacturing System

    Science.gov (United States)

    Li, Ning; Habuka, Hitoshi; Ikeda, Shin-ichi; Hara, Shiro

    A chemical vapor deposition reactor for producing thin silicon films was designed and developed for achieving a new electronic device production system, the Minimal Manufacturing, using a half-inch wafer. This system requires a rapid process by a small footprint reactor. This was designed and verified by employing the technical issues, such as (i) vertical gas flow, (ii) thermal operation using a highly concentrated infrared flux, and (iii) reactor cleaning by chlorine trifluoride gas. The combination of (i) and (ii) could achieve a low heating power and a fast cooling designed by the heat balance of the small wafer placed at a position outside of the reflector. The cleaning process could be rapid by (iii). The heating step could be skipped because chlorine trifluoride gas was reactive at any temperature higher than room temperature.

  12. A Study on the LEED Energy Simulation Process Using BIM

    Directory of Open Access Journals (Sweden)

    Han-Soo Ryu

    2016-02-01

    Full Text Available In the domestic and international environmentally friendly certification system, energy-related credit occupies a high ratio in the total distribution of certification score Leadership in the Energy and Environmental Design (LEED system is a certification system developed by the US Green Building Council (USGBC in order to assess the environmental friendliness of buildings. The energy-related credit is approximately 30% of the total and also the energy simulation ratio specifically is the highest among the single credits as it is 20%. In this research, the energy simulation process using Building Information Modeling (BIM based on the energy simulation case performed at the A-Tower, LEED certification was proposed. It places an emphasis on the verification process which was short in the previous research. The architectural geometry modeled through the BIM tool is converted to the gbXML, and in this process the geometry is verified through the interference check functions, the gbXML Viewer and the FZKViewer. The energy simulation is performed after the verification procedure. The geometry verification process in the A-Tower project is presented throughout this paper. In conclusion, an improved process is proposed for the productivity and reliability of energy simulation.

  13. Effect of Processing Methods on the Proximate and Energy ...

    African Journals Online (AJOL)

    Four methods of processing were assessed to investigate the effect of processing methods on the digestibility, proximate and energy composition of Lablab purpureus (Rongai) beans. The processing methods were boiling (in water), fermentation, toasting and fermentation plus toasting. Some of The beans were boiled for 0, ...

  14. Excitation energy transfer processes in condensed matter theory and applications

    CERN Document Server

    Singh, Jai

    1994-01-01

    Applying a unified quantum approach, contributors offer fresh insights into the theoretical developments in the excitation energy transfer processes in condensed matter This comprehensive volume examines Frenkel and Wannier excitonic processes; rates of excitonic processes; theory of laser sputter and polymer ablation; and polarons, excitonic polarons and self-trapping

  15. SU-E-I-106: Description of Energy Dose Deposition Kernel for the Diagnostic Beam.

    Science.gov (United States)

    Kareem, R; Liebmann, M; Chofor, N; Luellau, T; Poppe, B; von Ossietzky, Carl

    2012-06-01

    Over the recent years, the employment of kV x-rays as a diagnostic tool into clinical routine has resulted in a significant increase in the patient's exposure to ionizing radiation. The accurate determination of the absorbed dose to patients during diagnosis is therefore necessary to avoid unnecessary exposure to the patient. This study presents an analytical model of the energy deposition kernel for the monoenergetic and polyenergetic kV beams for the fast calculation of dose in radiography. The analytical model is based on the pencil beam kernels derived from Monte Carlo simulations. DOSXYZnrc code from the EGSnrc family was employed to simulate the pencil beam of 0.1 cm width for 80, 100 and 120 keV mono-energetic and polyenergetic beams. The lateral dose profiles were calculated at different depths within a homogenous water phantom of size 50×50×50 cm3 . The evaluated dose profiles showed a high amplitude primary component at the central axis and a long range low amplitude scatter component spanning a considerable distance from the central axis. The profiles were fitted analytically with a triple exponential decay function with an offset. All coefficients of the exponential function were further fitted with appropriate analytical functions to represent their behavior relative to depth and photon energy. The accuracy of the obtained kernel was checked by the convolution of a rectangular fluence profile and comparing the calculated dose distribution with the Monte Carlo simulated dose profiles for 2×2 cm2 field size. In a homogeneous phantom, the comparisons of the convolution method and Monte Carlo simulations showed sufficient agreement except for largest depths (deviation approx. 15%). Future developments will focus on an implementation of the method for dose calculation in the patient. © 2012 American Association of Physicists in Medicine.

  16. Energy deposition studies for the high-luminosity Large Hadron Collider inner triplet magnets

    Directory of Open Access Journals (Sweden)

    N. V. Mokhov

    2015-05-01

    Full Text Available A detailed model of the high-luminosity LHC inner triplet region with new large-aperture Nb_{3}Sn magnets, field maps, corrector packages, and segmented tungsten inner absorbers was built and implemented into the fluka and mars15 codes. Detailed simulations have been performed coherently with the codes on the impact of particle debris from the 14-TeV center-of-mass pp-collisions on the short- and long-term stability of the inner triplet magnets. After optimizing the absorber configuration, the peak power density averaged over the magnet inner cable width is found to be safely below the quench limit at the luminosity of 5×10^{34}  cm^{−2} s^{−1}. For the anticipated lifetime integrated luminosity of 3000  fb^{−1}, the peak dose calculated for the innermost magnet insulator ranges from 20 to 35 MGy, a figure close to the commonly accepted limit. Dynamic heat loads to the triplet magnet cold mass are calculated to evaluate the cryogenic capability. fluka and mars results on energy deposition are in very good agreement.

  17. Monitoring Approach to Evaluate the Performances of a New Deposition Nozzle Solution for DED Systems

    National Research Council Canada - National Science Library

    Federico Mazzucato; Simona Tusacciu; Manuel Lai; Sara Biamino; Mariangela Lombardi; Anna Valente

    2017-01-01

    In order to improve the process efficiency of a direct energy deposition (DED) system, closed loop control systems can be considered for monitoring the deposition and melting processes and adjusting the process parameters in real-time...

  18. Mapping process and age of Quaternary deposits on Santa Rosa Island, Channel Islands National Park, California

    Science.gov (United States)

    Schmidt, K. M.; Minor, S. A.; Bedford, D.

    2016-12-01

    Employing a geomorphic process-age classification scheme, we mapped the Quaternary surficial geology of Santa Rosa (SRI) within the Channel Islands National Park. This detailed (1:12,000 scale) map represents upland erosional transport processes and alluvial, fluvial, eolian, beach, marine terrace, mass wasting, and mixed depositional processes. Mapping was motivated through an agreement with the National Park Service and is intended to aid natural resource assessments, including post-grazing disturbance recovery and identification of mass wasting and tectonic hazards. We obtained numerous detailed geologic field observations, fossils for faunal identification as age control, and materials for numeric dating. This GPS-located field information provides ground truth for delineating map units and faults using GIS-based datasets- high-resolution (sub-meter) aerial imagery, LiDAR-based DEMs and derivative raster products. Mapped geologic units denote surface processes and Quaternary faults constrain deformation kinematics and rates, which inform models of landscape change. Significant findings include: 1) Flights of older Pleistocene (>120 ka) and possibly Pliocene marine terraces were identified beneath younger alluvial and eolian deposits at elevations as much as 275 m above modern sea level. Such elevated terraces suggest that SRI was a smaller, more submerged island in the late Neogene and (or) early Pleistocene prior to tectonic uplift. 2) Structural and geomorphic observations made along the potentially seismogenic SRI fault indicate a protracted slip history during the late Neogene and Quaternary involving early normal slip, later strike slip, and recent reverse slip. These changes in slip mode explain a marked contrast in island physiography across the fault. 3) Many of the steeper slopes are dramatically stripped of regolith, with exposed bedrock and deeply incised gullies, presumably due effects related to past grazing practices. 4) Surface water presence is

  19. Model Property Based Material Balance and Energy Conservation Analysis for Process Industry Energy Transfer Systems

    Directory of Open Access Journals (Sweden)

    Fumin Ma

    2015-10-01

    Full Text Available Conventional historical data based material and energy balance analyses are static and isolated computations. Such methods cannot embody the cross-coupling effect of energy flow, material flow and information flow in the process industry; furthermore, they cannot easily realize the effective evaluation and comparison of different energy transfer processes by alternating the model module. In this paper, a novel method for material balance and energy conservation analysis of process industry energy transfer system is developed based on model property. Firstly, a reconfigurable energy transfer process model, which is independent of energy types and energy-consuming equipment, is presented from the viewpoint of the cross-coupling effect of energy flow, material flow and information flow. Thereafter the material balance determination is proposed based on both a dynamic incidence matrix and dynamic balance quantity. Moreover, the model-weighted conservation determination theorem is proved, and the energy efficiency analysis method is also discussed. Results confirmed the efficacy of the proposed methods, confirming its potential for use by process industry in energy efficiency analyses.

  20. Microstructural Effects and Properties of Non-line-of-Sight Coating Processing via Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Harder, Bryan J.; Zhu, Dongming; Schmitt, Michael P.; Wolfe, Douglas E.

    2017-08-01

    Plasma spray-physical vapor deposition (PS-PVD) is a unique processing method that bridges the gap between conventional thermal spray and vapor phase methods, and enables highly tailorable coatings composed of a variety of materials in thin, dense layers or columnar microstructures with modification of the processing conditions. The strengths of this processing technique are material and microstructural flexibility, deposition speed, and potential for non-line-of-sight (NLOS) capability by vaporization of the feedstock material. The NLOS capability of PS-PVD is investigated here using yttria-stabilized zirconia and gadolinium zirconate, which are materials of interest for turbine engine applications. PS-PVD coatings were applied to static cylindrical substrates approximately 6-19 mm in diameter to study the coating morphology as a function of angle. In addition, coatings were deposited on flat substrates under various impingement configurations. Impingement angle had significant effects on the deposition mode, and microscopy of coatings indicated that there was a shift in the deposition mode at approximately 90° from incidence on the cylindrical samples, which may indicate the onset of more turbulent flow and PVD-like growth. Coatings deposited at non-perpendicular angles exhibited a higher density and nearly a 2× improvement in erosion performance when compared to coatings deposited with the torch normal to the surface.

  1. Characterization and Optimization of Mechanical Properties of ABS Parts Manufactured by the Fused Deposition Modelling Process

    Directory of Open Access Journals (Sweden)

    Godfrey C. Onwubolu

    2014-01-01

    Full Text Available While fused deposition modelling (FDM is one of the most used additive manufacturing (AM techniques today due to its ability to manufacture very complex geometries, the major research issues have been to balance ability to produce aesthetically appealing looking products with functionality. In this study, five important process parameters such as layer thickness, part orientation, raster angle, raster width, and air gap have been considered to study their effects on tensile strength of test specimen, using design of experiment (DOE. Using group method of data handling (GMDH, mathematical models relating the response with the process parameters have been developed. Using differential evolution (DE, optimal process parameters have been found to achieve good strength simultaneously for the response. The optimization of the mathematical model realized results in maximized tensile strength. Consequently, the additive manufacturing part produced is improved by optimizing the process parameters. The predicted models obtained show good correlation with the measured values and can be used to generalize prediction for process conditions outside the current study. Results obtained are very promising and hence the approach presented in this paper has practical applications for design and manufacture of parts using additive manufacturing technologies.

  2. High-energy wave deposits at the eastern shore of Bonaire (Netherlands Antilles)

    Science.gov (United States)

    Engel, M.; Willershäuser, T.; Bolten, A.; Brückner, H.; Daut, G.; Wennrich, V.; Kelletat, D.; Scheffers, A.; Scheffers, S. R.; Schäbitz, F.

    2009-04-01

    The island of Bonaire is part of the Leeward Netherlands Antilles and lies 90 km off the Venezuelan coast. It mainly consists of two upper cretaceous cores of basalt, andesite, and dacite, fringed by a sequence of Quaternary marine limestone terraces. These well-defined platforms formed by in-situ growth of coral reefs and deposition of coral debris during high stands of sea level and subsequent exposure due to slow tectonic uplift. Bonaire has a semi-arid climate with an average annual precipitation of less than 500 mm, though large year-to-year variation occurs. Due to its peripheral position within the Caribbean hurricane belt the island rarely experiences severe storm events. Nevertheless, along the eastern windward coast several high-energy wave impacts of mid- to late Holocene age have created a well-diversified sedimentary record. Broad ramparts of imbricated coral rubble north of Lac Bai are 4 m high, proceed up to 400 m inland, and follow the shore over a distance of 12 km. Reef communities of the island's eastern sublittoral obviously never regenerated after their destruction during extreme wave events. Furthermore, massive boulders of up to 260 tons are distributed over the broad elevated Pleistocene reef platform deriving from the foreshore zone (Scheffers et al., 2008). The windward nearshore morphological depressions provide excellent conditions for preserving sedimentary inputs of exceptionally large wave impacts. We carried out numerous vibracorings and gravity corings inside shallow sinkholes on the Pleistocene terrace north of Lac Bai and the landward floodplain of the Lagun embayment at Washikemba. Several vibracorings of up to 5 m below surface at Lagun show multiple interruptions of continuous sedimentation patterns by poorly-sorted shell hash within a carbonate-rich matrix of marine origin. The lowermost bioclastic unit dates back before 6000 BP. Within a superimposed layer of pure mangrove peat another cluster of shells, partly broken, is

  3. Instrumentation and Control for Fossil-Energy Processes

    Science.gov (United States)

    Mark, A., Jr.

    1984-01-01

    Instrumentation and control requirements for fossil-energy processes discussed in working document. Published to foster advancement of instrumentation and control technology by making equipment suppliers and others aware of specifications, needs, and potential markets.

  4. Energy Performance Indicators in the Swedish Building Procurement Process

    Directory of Open Access Journals (Sweden)

    Ingrid Allard

    2017-10-01

    Full Text Available In Sweden, all new buildings need to comply with the National Board of Housing, Building and Planning’s requirement on specific purchased energy (kWh/m2. Accordingly, this indicator is often used to set design criteria in the building procurement process. However, when energy use is measured in finished buildings, the measurements often deviate significantly from the design calculations. The measured specific purchased energy does not necessarily reflect the responsibility of the building contractor, as it is influenced by the building operation, user behavior and climate. Therefore, Swedish building practitioners may prefer other indicators for setting design criteria in the building procurement process. The aim of this study was twofold: (i to understand the Swedish building practitioners’ perspectives and opinions on seven building energy performance indicators (envelope air leakage, U-values for different building parts, average U-value, specific heat loss, heat loss coefficient, specific net energy, and specific purchased energy; and (ii to understand the consequences for the energy performance of multi-family buildings of using the studied indicators to set criteria in the procurement process. The study involved a Delphi approach and simulations of a multi-family case study building. The studied indicators were discussed in terms of how they may meet the needs of the building practitioners when used to set building energy performance criteria in the procurement process.

  5. Energy enhancer for mask based laser materials processing

    DEFF Research Database (Denmark)

    Bastue, Jens; Olsen, Flemmming Ove

    1996-01-01

    A device capable of drastically improving the energy efficiency of present mask based laser materials processing systems is presented. Good accordance between experiments and simulations for a TEA-CO2 laser system designed for laser marking has been demonstrated. The energy efficiency may...

  6. Wind Energy Deployment Process and Siting Tools (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Tegen, S.

    2015-02-01

    Regardless of cost and performance, some wind projects cannot proceed to completion as a result of competing multiple uses or siting considerations. Wind energy siting issues must be better understood and quantified. DOE tasked NREL researchers with depicting the wind energy deployment process and researching development considerations. This presentation provides an overview of these findings and wind siting tools.

  7. Evolution of Texture from a Single Crystal Ti-6Al-4V Substrate During Electron Beam Directed Energy Deposition

    Science.gov (United States)

    Butler, Todd M.; Brice, Craig A.; Tayon, Wesley A.; Semiatin, S. Lee; Pilchak, Adam L.

    2017-10-01

    Additive manufacturing of Ti-6Al-4V commonly produces 〈001〉 β -fiber textures aligned with the build direction. We have performed wire-feed electron beam directed energy deposition on the {112} β plane of a single prior β-grain. The build initially grew epitaxially from the substrate with the preferred 〈001〉 growth direction significantly angled away from the build direction. However, continued layer deposition drove the formation of a 〈001〉 β -fiber texture aligned with the build direction and the direction of the strongest thermal gradient.

  8. Correlation of process parameters and properties of TiO2 films grown by ion beam sputter deposition from a ceramic target

    Science.gov (United States)

    Bundesmann, Carsten; Lautenschläge, Thomas; Spemann, Daniel; Finzel, Annemarie; Mensing, Michael; Frost, Frank

    2017-10-01

    The correlation between process parameters and properties of TiO2 films grown by ion beam sputter deposition from a ceramic target was investigated. TiO2 films were grown under systematic variation of ion beam parameters (ion species, ion energy) and geometrical parameters (ion incidence angle, polar emission angle) and characterized with respect to film thickness, growth rate, structural properties, surface topography, composition, optical properties, and mass density. Systematic variations of film properties with the scattering geometry, namely the scattering angle, have been revealed. There are also considerable differences in film properties when changing the process gas from Ar to Xe. Similar systematics were reported for TiO2 films grown by reactive ion beam sputter deposition from a metal target [C. Bundesmann et al., Appl. Surf. Sci. 421, 331 (2017)]. However, there are some deviations from the previously reported data, for instance, in growth rate, mass density and optical properties.

  9. Effect of voltage on the characteristics of magnesium-lanthanum deposits synthesized by an electrodeposition process

    Energy Technology Data Exchange (ETDEWEB)

    Sahli, M. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Chetehouna, K.; Gascoin, N. [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France); Bellel, N. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Tadini, P., E-mail: tadini.pietro@gmail.com [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France)

    2017-04-15

    This work deals with the characterization of magnesium-lanthanum powders deposits produced with an electrodeposition technique using an aqueous solution based on magnesium chloride and lanthanum(III) nitrate. In recent years, the interest for magnesium-based alloys is growing due to their potential use as solid state systems for hydrogen storage. This work is a preliminary study on the synthesis of magnesium-lanthanum powders oriented to their later evaluation in systems for hydrogen storage. Magnesium and Lanthanum are deposited on a copper plate used as a cathode. Chemical composition, structure and morphology are investigated by EDS, XRD, FTIR and SEM. The effect of voltage on powders characteristics is studied considering three values (3, 3.5 and 4 V). EDS analysis shows the presence of three major elements (Mg, La and O) with a little amount of Cl. The weight percentages of Mg and O increase whereas the one of La decreases with the growth of voltage. Morphological characterization reveals that heterogeneous chemical structures are formed on the surface of the electrode and the size of aggregates decreases with the increase of voltage. From the results of X-ray analysis the deposits reveal the significant presence of two phases: Mg(OH){sub 2} and La(OH){sub 3}. The peaks originating from the Mg(OH){sub 2} phase has a non-monotonic behavior and those of La(OH){sub 3} phase increase with the increase of voltage. FTIR analysis confirms the presence of the two phases identified in XRD diffractograms and exhibits that their corresponding transmittance values increase for higher voltage values. - Highlights: • Synthesis of magnesium-lanthanum deposits by an electrodeposition process. • Voltage effect is investigated using different physicochemical analysis techniques (EDS, XRD, FTIR and SEM). • The EDS analysis shows the presence of three major elements (Mg, La and O) and a little amount of Cl. • Two phases, namely Mg(OH){sub 2} and La(OH){sub 3} are

  10. Effects of deposition methods and processing techniques on band gap, interband electronic transitions, and optical absorption in perovskite CH3NH3PbI3 films

    Science.gov (United States)

    Li, Wenwu; Sha, Tingting; Wang, Yan; Yu, Wenlei; Jiang, Kai; Zhou, Hang; Liu, Chuan; Hu, Zhigao; Chu, Junhao

    2017-07-01

    Despite intensive studies on the improvements of conversion efficiencies in solar cells, many questions regarding the effects of deposition techniques on optical properties and electronic band structures of CH3NH3PbI3 (MAPbI3) remain unresolved. Here, perovskite MAPbI3 films were prepared using different deposition methods and processing techniques. The effects of deposition and processing parameters on dielectric functions and optical absorption were investigated by fitting the reflectance spectra in the photon energy range of 0.5-5.16 eV. It is found that the bandgap (Eg) of the films deposited by two-step spinning (1.591 eV) is larger than that prepared by evaporations (1.514 eV), due to different Pb-I orbital hybridization and spin-orbit coupling. Moreover, the Eg value of the films increases from 1.543 eV to 1.591 eV after toluene solution dripping. Five interband electronic transitions ( Ep 1, Ep 2, Ep 3, Ep 4 , and Ep 5 ) are observed, and the origins of Ep 2, Ep 3 , and Ep 4 are assigned to the direct transitions between the highest valence band and the lowest lying conduction band at the R, M, and X symmetry points. Further, the transition energies of the films deposited by evaporation are less than those prepared by two-step spinning. The present results shed light on preparing more reliable and reproducible high performance MAPbI3-based solar cells.

  11. Evaluating the signatures of fluvial, wave, and tidal processes on deltaic deposits in the Cretaceous Western Interior Seaway

    Science.gov (United States)

    Hajek, E. A.; Trampush, S. M.

    2014-12-01

    Characteristic differences in delta morphology suggest different balances of wave, tidal, and fluvial processes on different coastlines. These insights have been used to interpret stratigraphic deposits and reconstruct paleogeography of ancient fluvial-deltaic environments. This work is often accomplished through combined efforts to map the architecture of ancient delta deposits and document the abundance and distribution of sedimentary structures that indicate sediment transport by uni- or bi-directional currents or waves. Statistical tools for quantifying sedimentation patterns in ancient deposits provide an opportunity to directly compare architectural patterns among ancient delta deposits. In order to evaluate the degree to which interpreted influence of waves or tides is manifested as a change in delta architecture, we compare detailed stratigraphic measurements from ancient deposits. Well-studied Cretaceous deltaic deposits in the Western Interior Seaway (USA), including the Ferron and Sego formations, have been interpreted as reflecting wave- and tide-influenced conditions, respectively. Using measurements made in the field and from terrestrial lidar outcrop scans, we compare the compensation index and paleohydraulic reconstructions from distributary channel deposits in order to quantify sedimentary architecture in each unit. Preliminary results suggest that the scaling and architecture of topset, foreset, and prodelta deposits in each of these units may have been broadly similar, despite distinct differences in the abundance of wave- and tidal-indicators present within each unit. This indicates that the presence of traditionally diagnostic deposits, particularly sedimentary structures indicative of fluvial, tidal, or wave processes, may not accurately reflect the balance of these processes acting on paleo-shorelines.

  12. Thermal analysis of fused deposition modeling process using infrared thermography imaging and finite element modeling

    Science.gov (United States)

    Zhou, Xunfei; Hsieh, Sheng-Jen

    2017-05-01

    After years of development, Fused Deposition Modeling (FDM) has become the most popular technique in commercial 3D printing due to its cost effectiveness and easy-to-operate fabrication process. Mechanical strength and dimensional accuracy are two of the most important factors for reliability of FDM products. However, the solid-liquid-solid state changes of material in the FDM process make it difficult to monitor and model. In this paper, an experimental model was developed to apply cost-effective infrared thermography imaging method to acquire temperature history of filaments at the interface and their corresponding cooling mechanism. A three-dimensional finite element model was constructed to simulate the same process using element "birth and death" feature and validated with the thermal response from the experimental model. In 6 of 9 experimental conditions, a maximum of 13% difference existed between the experimental and numerical models. This work suggests that numerical modeling of FDM process is reliable and can facilitate better understanding of bead spreading and road-to-road bonding mechanics during fabrication.

  13. Endogenous magnetic reconnection and associated high energy plasma processes

    Science.gov (United States)

    Coppi, B.; Basu, B.

    2018-02-01

    An endogenous reconnection process involves a driving factor that lays inside the layer where a drastic change of magnetic field topology occurs. A process of this kind is shown to take place when an electron temperature gradient is present in a magnetically confined plasma and the evolving electron temperature fluctuations are anisotropic. The width of the reconnecting layer remains significant even when large macroscopic distances are considered. In view of the fact that there are plasmas in the Universe with considerable electron thermal energy contents this feature can be relied upon in order to produce generation or conversion of magnetic energy, high energy particle populations and momentum and angular momentum transport.

  14. Atmospheric pressure chemical vapor deposition of ZnO: Process modeling and experiments

    NARCIS (Netherlands)

    Deelen, J. van; Illiberi, A.; Kniknie, B.; Beckers, E.H.A.; Simons, P.J.P.M.; Lankhorst, A.

    2014-01-01

    The deposition of zinc oxide has been performed by atmospheric pressure chemical vapor deposition and trends in growth rates are compared with the literature. Diethylzinc and tertiary butanol were used as the primary reactants and deposition rates above 800 nm/min were obtained. The reaction

  15. Atmospheric pressure chemical vapor deposition of ZnO: Process modeling and experiments

    NARCIS (Netherlands)

    Deelen, J. van; Illiberi, A.; Kniknie, B.; Beckers, E.H.A.; Simons, P.J.P.M.; Lankhorst, A.

    2013-01-01

    The deposition of zinc oxide has been performed by atmospheric pressure chemical vapor deposition and trends in growth rates are compared with the literature. Diethylzinc and tertiary butanol were used as the primary reactants and deposition rates above 800 nm/minwere obtained. The reaction

  16. Manufacturing processes of cellular metals. Part II. Solid route, metals deposition, other processes; Procesos de fabricacion de metales celulares. Parte II: Via solida, deposicion de metales otros procesos

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, P.; Cruz, L. J.; Coleto, J.

    2009-07-01

    At the first part of this paper review a description about cellular metal processes by liquid route, was made. In this second part, solid processes and metals deposition are described. In similar way, the different kind of processes in each case are reviewed; making a short description about the main parameters involved and the advantages and drawbacks in each of them. (Author) 147 refs.

  17. Food and drink processing: Introducing energy saving opportunities for business

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-04-15

    The food and drink processing industry is the fourth highest industrial energy user in the UK. In 2000, it consumed nearly 70TWh (enough energy to power one million homes for nearly 15 years) and emitted around 13 million tonnes of carbon dioxide into the atmosphere. Energy consumption in the sector could be considerably reduced by implementing simple and effective energy saving measures, reducing carbon emissions and cutting the costs for businesses. This publication is aimed at managers in the industry working in all sub-sectors. Focusing on the low and no-cost measures and actions which will have the quickest payback, this overview demonstrates the best energy saving opportunities in the sector. The industry is very diverse with many sub-sectors. Each sub-sector employs a range of industrial processes. This guide concentrates on technologies and management techniques that offer the greatest potential for energy saving and that are common to the widest range of sub-sectors. These are: Refrigeration; Process measurement and control; Compressed air; Motors and drives; Boilers and heat distribution; Cooking; Distillation, drying and evaporation; Energy management. The relative importance of each area will also depend on the sub-sector. For example, refrigeration cost will make up a large proportion of energy bills in the frozen and chilled foods sub-sector. Equally, for a business that produces confectionery, boilers and heat distribution systems will make the largest contribution. (GB)

  18. Characterization of ultra-short pulsed discharge plasma for CVD processing. [Chemical Vapor Deposition

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, Akira (Toyohashi Univ. of Technology (Japan). Dept. of Ecological Engineering); Okazaki, Ken (Tokyo Inst. of Technology (Japan). Research Center for Carbon Recycling and Utilization); Takekoshi, Takashi (Mitsubishi Kasei Co., Okayama (Japan). Mizushima Works); Tobe, Ryoki (Anelva Corp., Tokyo (Japan). Research Development Center)

    Characteristics of pulsed discharge plasma of methane-hydrogen gas mixture and Ar gas have been studied for active control of plasma chemical vapor deposition (CVD) processing. Voltage-current characteristics, time-lag of the current pulse, and the photon emission intensity profile have been investigated using high-voltage pulses of 50-1000 ns duration. In such a pulse discharge, voltages much higher than those in a dc glow discharge can be applied without any plasma nonuniformity or arcing because voltage amplitude falls to zero before glow to arc transition. A current value of more than 10[sup 3] times those in a glow discharge can be established. Very high photon emission intensity from CH radicals and H ions have been observed near the anode in a pulsed plasma. This is different in dc plasma, where the negative glow region near the cathode is the brightest.

  19. Height Control and Deposition Measurement for the Electron Beam Free Form Fabrication (EBF3) Process

    Science.gov (United States)

    Seufzer, William J. (Inventor); Hafley, Robert A. (Inventor)

    2017-01-01

    A method of controlling a height of an electron beam gun and wire feeder during an electron freeform fabrication process includes utilizing a camera to generate an image of the molten pool of material. The image generated by the camera is utilized to determine a measured height of the electron beam gun relative to the surface of the molten pool. The method further includes ensuring that the measured height is within the range of acceptable heights of the electron beam gun relative to the surface of the molten pool. The present invention also provides for measuring a height of a solid metal deposit formed upon cooling of a molten pool. The height of a single point can be measured, or a plurality of points can be measured to provide 2D or 3D surface height measurements.

  20. Dynamic through-silicon-via filling process using copper electrochemical deposition at different current densities

    Science.gov (United States)

    Wang, Fuliang; Zhao, Zhipeng; Nie, Nantian; Wang, Feng; Zhu, Wenhui

    2017-01-01

    This work demonstrates the dynamic through-silicon-via (TSV) filling process through staged electrodeposition experiments at different current densities. Different morphologies corresponding to TSV filling results can be obtained by controlling the applied current density. Specifically, a low current density (4 mA/cm2) induces seam defect filling, a medium current density (7 mA/cm2) induces defect-free filling, and a high current density (10 mA/cm2) induces void defect filling. Analysis of the filling coefficient indicates that the effect of current density on the TSV filling models is triggered by the coupling effect of consumption and diffusion of additives and copper ions. Further, the morphological evolution of plating reveals that the local deposition rate is affected by the geometrical characteristics of the plating. PMID:28422170

  1. Realization of tellurium-based all dielectric optical metamaterials using a multi-cycle deposition-etch process

    Science.gov (United States)

    Liu, Sheng; Ihlefeld, Jon F.; Dominguez, Jason; Gonzales, Edward F.; Eric Bower, John; Bruce Burckel, D.; Sinclair, Michael B.; Brener, Igal

    2013-04-01

    Tellurium (Te) dielectric resonator metamaterials for thermal infrared applications were fabricated using a multi-cycle deposition-etch process that circumvents pinch-off issues during deposition. Deposition and etching of Te were studied in detail. Metamaterial samples with varying resonator dimensions were fabricated using this technique. All the samples showed two transmission minima corresponding to magnetic and electric dipole resonances. Longer resonant wavelengths were observed as the resonator dimension was increased. Observation of spectral overlap between magnetic and electric resonances gives us the potential opportunity to realize a negative refractive index material.

  2. Studies in graphene growth and processing using atmospheric pressure chemical vapor deposition

    Science.gov (United States)

    Merrell, Andrew Nephi

    This dissertation focuses on graphene, a promising two-dimensional, carbon material with many favorable electronic properties. The prospect of implementing graphene into a wide variety of potential device applications is enticing, but many factors stand in the way before this goal is realized. Atmospheric pressure chemical vapor deposition (APCVD) is a graphene production method that may be compatible with large-scale growth. Motivated by the need to more fully understand APCVD growth of graphene, a system is constructed, and several studies are carried out. Specifically, a detailed study is presented which involves the effects of hydrogen and contaminant oxygen in APCVD-grown graphene. The research shows that hydrogen is an important factor to control during the cooling stage of APCVD, as it has a direct effect on the formation of oxides on the copper foil (copper is used as the catalyst for graphene growth in APCVD). It is also determined that hydrogen, as well as the reaction chamber, play an important role in the formation of SiO2 nanoparticles, which accumulate on the copper surface during graphene growth. Methods for patterning and processing graphene are also explored in this dissertation, as such methods are crucial in the realization of graphene-based devices. The method of e-beam assisted metal deposition used in conjunction with masked-CVD growth is proposed as an effective alternative to conventional processing methods such as photolithography and electron-beam lithography. The proposed methods have several advantages, which pave the way for lowering graphene/metal contact resistance, and preserving the intrinsic properties of graphene during device fabrication.

  3. Study of Z scaling of runaway electron plateau final loss energy deposition into wall of DIII-D

    Science.gov (United States)

    Hollmann, E. M.; Commaux, N.; Eidietis, N. W.; Lasnier, C. J.; Rudakov, D. L.; Shiraki, D.; Cooper, C.; Martin-Solis, J. R.; Parks, P. B.; Paz-Soldan, C.

    2017-06-01

    Controlled runaway electron (RE) plateau-wall strikes with different initial impurity levels are used to study the effect of background plasma ion charge Z (resistivity) on RE-wall loss dynamics. It is found that Joule heating (magnetic to kinetic energy conversion) during the final loss does not go up monotonically with increasing Z but peaks at intermediate Z ˜ 6. Joule heating and overall time scales of the RE final loss are found to be reasonably well-described by a basic 0D coupled-circuit model, with only the loss time as a free parameter. This loss time is found to be fairly well correlated with the avalanche time, possibly suggesting that the RE final loss rate is limited by the avalanche rate. First attempts at measuring total energy deposition to the vessel walls by REs during the final loss are made. At higher plasma impurity levels Z > 5, energy deposition to the wall appears to be consistent with modeling, at least within the large uncertainties of the measurement. At low impurity levels Z deposition appears around 5-20× less than expected, suggesting that the RE energy dissipation at low Z is not fully understood.

  4. Reconstruction of Axial Energy Deposition in Magnetic Liner Inertial Fusion Based on PECOS Shadowgraph Unfolds Using the AMR Code FLASH

    Science.gov (United States)

    Adams, Marissa; Jennings, Christopher; Slutz, Stephen; Peterson, Kyle; Gourdain, Pierre; U. Rochester-Sandia Collaboration

    2017-10-01

    Magnetic Liner Inertial Fusion (MagLIF) experiments incorporate a laser to preheat a deuterium filled capsule before compression via a magnetically imploding liner. In this work, we focus on the blast wave formed in the fuel during the laser preheat component of MagLIF, where approximately 1kJ of energy is deposited in 3ns into the capsule axially before implosion. To model blast waves directly relevant to experiments such as MagLIF, we inferred deposited energy from shadowgraphy of laser-only experiments preformed at the PECOS target chamber using the Z-Beamlet laser. These energy profiles were used to initialize 2-dimensional simulations using by the adaptive mesh refinement code FLASH. Gradients or asymmetries in the energy deposition may seed instabilities that alter the fuel's distribution, or promote mix, as the blast wave interacts with the liner wall. The AMR capabilities of FLASH allow us to study the development and dynamics of these instabilities within the fuel and their effect on the liner before implosion. Sandia Natl Labs is managed by NTES of Sandia, LLC., a subsidiary of Honeywell International, Inc, for the U.S. DOEs NNSA under contract DE-NA0003525.

  5. Influence of electronic energy deposition on the structural modification of swift heavy-ion-irradiated amorphous germanium layers

    Science.gov (United States)

    Steinbach, T.; Schnohr, C. S.; Kluth, P.; Giulian, R.; Araujo, L. L.; Sprouster, D. J.; Ridgway, M. C.; Wesch, W.

    2011-02-01

    Swift heavy-ion (SHI) irradiation of amorphous germanium (a-Ge) layers leads to a strong volume expansion accompanied by a nonsaturating irreversible plastic deformation (ion hammering), which are consequences of the high local electronic energy deposition within the region of the a-Ge layer. We present a detailed study of the influence of SHI irradiation parameters on the effect of plastic deformation and structural modification. Specially prepared a-Ge layers were irradiated using two SHI energies and different angles of incidence, thus resulting in a variation of the electronic energy deposition per depth ɛe between 14.0 and 38.6 keV nm-1. For all irradiation parameters used a strong swelling of the irradiated material was observed, which is caused by the formation and growth of randomly distributed voids, leading to a gradual transformation of the amorphous layer into a sponge-like porous structure as established by cross-section scanning electron microscopy investigations. The swelling depends linearly on the ion fluence and on the value of ɛe, thus clearly demonstrating that the structural changes are determined solely by the electronic energy deposited within the amorphous layer. Plastic deformation shows a superlinear dependence on the ion fluence due to the simultaneous volume expansion. This influence of structural modification on plastic deformation is described by a simple approach, thus allowing estimation of the deformation yield. With these results the threshold values of the electronic energy deposition for the onset of both structural modification and plastic deformation due to SHI irradiation are determined. Furthermore, based on these results, the longstanding question concerning the reason for the structural modification observed in SHI-irradiated crystalline Ge is answered.

  6. ACCELERATING THE ADOPTION PROCESS OF RENEWABLE ENERGY SOURCES AMONG SMES

    Directory of Open Access Journals (Sweden)

    Mirjam Leloux

    2015-07-01

    solar panel installation, heat pumps and wind energy, generating electricity. We have a two-track approach: development of a tool to support SMEs in their decision making process about suitable and appropriate technologies and solutions, and research to understand the barriers and obstacles that hinder adoption and implementation of sustainable energy solutions. In this paper we introduce a tool which aims to support SMEs in their decision making process on renewable energy applications in the expectation that this will accelerate that process.

  7. High-energy, high-rate materials processing

    Science.gov (United States)

    Marcus, H. L.; Bourell, D. L.; Eliezer, Z.; Persad, C.; Weldon, W.

    1987-12-01

    The increasingly available range of pulsed-power, high energy kinetic storage devices, such as low-inductance pulse-forming networks, compulsators, and homopolar generators, is presently considered as a basis for industrial high energy/high rate (HEHR) processing to accomplish shock hardening, drilling, rapid surface alloying and melting, welding and cutting, transformation hardening, and cladding and surface melting in metallic materials. Time-temperature-transformation concepts furnish the basis for a fundamental understanding of the potential advantages of this direct pulsed power processing. Attention is given to the HEHR processing of a refractory molybdenum alloy, a nickel-base metallic glass, tungsten, titanium aluminides, and metal-matrix composites.

  8. SU-E-T-510: Calculation of High Resolution and Material-Specific Photon Energy Deposition Kernels.

    Science.gov (United States)

    Huang, J; Childress, N; Kry, S

    2012-06-01

    To calculate photon energy deposition kernels (EDKs) used for convolution/superposition dose calculation at a higher resolution than the original Mackie et al. 1988 kernels and to calculate material-specific kernels that describe how energy is transported and deposited by secondary particles when the incident photon interacts in a material other than water. The high resolution EDKs for various incident photon energies were generated using the EGSnrc user-code EDKnrc, which forces incident photons to interact at the center of a 60 cm radius sphere of water. The simulation geometry is essentially the same as the original Mackie calculation but with a greater number of scoring voxels (48 radial, 144 angular bins). For the material-specific EDKs, incident photons were forced to interact at the center of a 1 mm radius sphere of material (lung, cortical bone, silver, or titanium) surrounded by a 60 cm radius water sphere, using the original scoring voxel geometry implemented by Mackie et al. 1988 (24 radial, 48 angular bins). Our Monte Carlo-calculated high resolution EDKs showed excellent agreement with the Mackie kernels, with our kernels providing more information about energy deposition close to the interaction site. Furthermore, our EDKs resulted in smoother dose deposition functions due to the finer resolution and greater number of simulation histories. The material-specific EDK results show that the angular distribution of energy deposition is different for incident photons interacting in different materials. Calculated from the angular dose distribution for 300 keV incident photons, the expected polar angle for dose deposition () is 28.6° for water, 33.3° for lung, 36.0° for cortical bone, 44.6° for titanium, and 58.1° for silver, showing a dependence on the material in which the primary photon interacts. These high resolution and material-specific EDKs have implications for convolution/superposition dose calculations in heterogeneous patient geometries

  9. Evolution and preservation potential of fluvial and transgressive deposits on the Louisiana inner shelf: Understanding depositional processes to support coastal management

    Science.gov (United States)

    Flocks, J.; Miner, M.D.; Twichell, D.C.; Lavoie, D.L.; Kindinger, J.

    2009-01-01

    The barrier-island systems of the Mississippi River Delta plain are currently undergoing some of the highest rates of shoreline retreat in North America (???20 m/year). Effective management of this coastal area requires an understanding of the processes involved in shoreline erosion and measures that can be enacted to reduce loss. The dominant stratigraphy of the delta plain is fluvial mud (silts and clays), delivered in suspension via a series of shallow-water delta lobes that prograded across the shelf throughout the Holocene. Abandonment of a delta lobe through avulsion leads to rapid land subsidence through compaction within the muddy framework. As the deltaic headland subsides below sea level, the marine environment transgresses the bays and wetlands, reworking the available sands into transgressive barrier shorelines. This natural process is further complicated by numerous factors: (1) global sea-level rise; (2) reduced sediment load within the Mississippi River; (3) diversion of the sediment load away from the barrier shorelines to the deep shelf; (4) storm-induced erosion; and (5) human alteration of the littoral process through the construction of hardened shorelines, canals, and other activities. This suite of factors has led to the deterioration of the barrier-island systems that protect interior wetlands and human infrastructure from normal wave activity and periodic storm impact. Interior wetland loss results in an increased tidal prism and inlet cross-sectional areas, and expanding ebb-tidal deltas, which removes sand from the littoral processes through diversion and sequestration. Shoreface erosion of the deltaic headlands does not provide sufficient sand to balance the loss, resulting in thinning and dislocation of the islands. Abatement measures include replenishing lost sediment with similar material, excavated from discrete sandy deposits within the muddy delta plain. These sand bodies were deposited by the same cyclical processes that formed the

  10. Energy aspects and potential energy savings of the new DASI process for milk sterilization

    Energy Technology Data Exchange (ETDEWEB)

    Frey, B.C. (Univ. of Maryland, College Park); Stewart, L.E.; Chandarana, D.; Wolfson, R.P.

    1981-01-01

    An experimental study was conducted to determine the difference in total processing energy required by the DASI ultra-high temperature (UHT) system and a conventional high temperature short time (HTST) fluid milk system. Data available in the literature were used to develop an energy use profile for the current US fluid milk system from processor to consumer. The energy data measured and the profile developed were used to estimate the potential energy savings resulting from the introduction of sterile milk in the US fluid milk market. Savings of energy resulting from the introduction of sterile milk were estimated to be 12 million barrels of oil annually.

  11. Managing the energy efficiency of a process sensor network

    Energy Technology Data Exchange (ETDEWEB)

    Karjalainen, S.; Karjalainen, T. (Univ. of Oulu, Measurement and Sensor Lab., Kajaani (Finland)). email: seppo.karjalainen@oulu.fi

    2009-07-01

    A wireless data transfer is nowadays quite easy and affordable to implement in most cases. If the wireless sensor network (Wsrn) is deployed in a very difficult environment or requires great data transfer speeds, as in many industrial and process environments, this might not always be the case. The main reason slowing the deployment of WSNs is the difficulty of supplying enough energy to the sensor nodes. In most cases all of the energy the node consumes must be stored or produced at the node. The difficulty of supplying enough energy for the nodes can shorten the maintenance interval of the nodes to an unpractical level. In this research project we study the possibilities of managing the energy efficiency (saving energy, producing energy) of a wireless process measurement system. The main focus areas of the project are saving and producing energy at the network nodes. Energy consumption is the main limitation while designing WSNs. To extend each sensor node's lifetime it is necessary to reduce power dissipation as much as possible. A sensor node is a complex device comprising of various parts, each of which must be carefully selected and utilized in order to reach the lowest possible energy consumption. The level of energy efficiency of a sensor network is greatly affected by the way we balance the goal of low energy consumption with the other requirements placed on the network. The requirements for a deployed WSN depend on the application and the operating environment. Hence, the generalization of the requirements in detail is not practical. Nonetheless sensor network applications possess several characteristics, based on which general requirements for the node platforms, protocols and applications can be defined. The relative importance of each requirement depends heavily on the application area. In this project we produce a report covering all the various aspects of managing the energy efficiency in a wireless sensor network. The physical components and

  12. Thermal Characteristic Of Waste-Derived Hydroxyapatite (HA) Reinforced Ultra High Molecular Weight Polyethylene (UHMWPE) Composites For Fused Deposition Modeling (FDM) Process

    Science.gov (United States)

    Ansari, Mohamad Helmi Bin Md; Ibrahim, Mohd Halim Irwan Bin

    2017-01-01

    The present study provides a hydrothermal synthesis to obtain Hydroxyapatite (HA) powder from waste eggshells. This waste-derived HA has been characterized by X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy analysis. Waste-derived HA will be reinforced the Ultra-High Molecular Weight Polyethylene (UHMWPE) to develop a material composite for biomedical applications because of impressive mechanical properties owned by UHMWPE. Main challenger is UHMWPE has an ultra-high viscosity that renders continuous melt- state processes including one of the additive manufacturing processes which is Fused Deposition Modeling (FDM). To develop this material as feedstock in FDM process, it has been overcome by blending UHMWPE with waste-derived HA as filler. It exhibit the inclusion of 50wt% HA has reduced the degradation temperature in TGA and DSC thus enhances the processability in FDM process.

  13. On the Deposition Equilibrium of Carbon Nanotubes or Graphite in the Reforming Processes of Lower Hydrocarbon Fuels

    Directory of Open Access Journals (Sweden)

    Zdzisław Jaworski

    2017-11-01

    Full Text Available The modeling of carbon deposition from C-H-O reformates has usually employed thermodynamic data for graphite, but has rarely employed such data for impure filamentous carbon. Therefore, electrochemical data for the literature on the chemical potential of two types of purified carbon nanotubes (CNTs are included in the study. Parameter values determining the thermodynamic equilibrium of the deposition of either graphite or CNTs are computed for dry and wet reformates from natural gas and liquefied petroleum gas. The calculation results are presented as the atomic oxygen-to-carbon ratio (O/C against temperature (200 to 100 °C for various pressures (1 to 30 bar. Areas of O/C for either carbon deposition or deposition-free are computed, and indicate the critical O/C values below which the deposition can occur. Only three types of deposited carbon were found in the studied equilibrium conditions: Graphite, multi-walled CNTs, and single-walled CNTs in bundles. The temperature regions of the appearance of the thermodynamically stable forms of solid carbon are numerically determined as being independent of pressure and the analyzed reactants. The modeling indicates a significant increase in the critical O/C for the deposition of CNTs against that for graphite. The highest rise in the critical O/C, of up to 290% at 30 bar, was found for the wet reforming process.

  14. Prevention of the ash deposits by means of process conditions in biomass gasification; Biomassapolttoaineiden tuhkan kuonaantumiskaeyttaeytymisen estaeminen prosessiolosuhteiden avulla

    Energy Technology Data Exchange (ETDEWEB)

    Moilanen, A.; Laatikainen-Luntama, J.; Nieminen, M.; Kurkela, E.; Korhonen, J. [VTT Energy, Espoo (Finland)

    1997-10-01

    In fluidised-bed gasification, various types of deposits and agglomerates may be formed by biomass ash in the bed, in upper zones of the reactor, for instance in cyclones. These may decisively hamper the operation of the process. The aim of the project was to obtain data on the detrimental fouling behaviour of the ash of different types of biomass in fluidised-bed gasification, and on the basis of these data to determine the process conditions and ways of preventing this kind of behaviour. Different types of biomass fuel relevant to energy production such as straw, wood residue were be used as samples. The project consisted of laboratory studies and fluidised-bed reactor tests including ash behaviour studied both in the bed and freeboard. In laboratory tests, the sample material was characterised as a function of different process parameters. In fluid-bed reactors, the most harmful biomasses were tested using process variables such as temperature, bed material and the gasification agents. Bubbling fluidised-bed gasification tests with wheat straw showed that agglomerates with different sizes and structures formed in the bed depending on the temperature, the feed gas composition and bed material. Agglomerates consisted of molten ash which sintered with bed material and other solids. In all BFB tests, freeboard walls were slicked by ash agglomerates (different amounts) which, however, were easily removable. The results of this project and the earlier pilot-scale gasification experience obtained with the same feedstocks showed that useful characteristic data about ash behaviour can be obtained using laboratory tests and small scale reactors. (orig.)

  15. Ozone deposition in a mixed forest ecosystem - temporal variation and removal processes

    Science.gov (United States)

    Pokorska, Olga; Gruening, Carsten; Goded, Ignacio

    2016-04-01

    Forests are a major sink for tropospheric ozone, however the fate of ozone within the forest canopy is still not well understood. In this study we will present results of 3 years ozone flux measurements at eddy covariance flux tower in Ispra (Northern Italy) over mixed forest ecosystem. The main tree species in this ecosystem are Quercus robur (80%), Alnus glutinosa (10%), Populus alba (5%) and Carpinus betulus (3%). The measurements were carried out continuously from January 2013 till December 2015. Flux measurements at the canopy level with the eddy covariance technique were complemented with measurements of meteorological parameters and measurements of VOCs (Volatile Organic Compounds) using PTR-MS (Proton Transfer Reaction - Mass Spectrometry) during an intensive observation period. Continuous measurements produced a big dataset which allowed us to investigate the controls on ozone fluxes and to do multiyear comparisons. Patterns of ozone concentration, ozone fluxes and ozone deposition velocity over forest canopy will be presented in relation to physiological activity of the trees and time of the year. Current research is mainly aimed at better understanding of the contribution of destruction processes within the canopy. Therefore, the collected data were used to calculate the partitioning of total ozone fluxes between stomatal and non-stomatal sinks. We found that the stomatal uptake contributed less that non-stomatal uptake to the total ozone flux during the growing seasons. In particular, non-stomatal ozone removal by reactions with isoprene and other VOCs will be discussed. We will present contribution and change of individual ozone deposition sinks over the years in response to environmental parameters.

  16. Improving energy audit process and report outcomes through planning initiatives

    Science.gov (United States)

    Sprau Coulter, Tabitha L.

    Energy audits and energy models are an important aspect of the retrofit design process, as they provide project teams with an opportunity to evaluate a facilities current building systems' and energy performance. The information collected during an energy audit is typically used to develop an energy model and an energy audit report that are both used to assist in making decisions about the design and implementation of energy conservation measures in a facility. The current lack of energy auditing standards results in a high degree of variability in energy audit outcomes depending on the individual performing the audit. The research presented is based on the conviction that performing an energy audit and producing a value adding energy model for retrofit buildings can benefit from a revised approach. The research was divided into four phases, with the initial three phases consisting of: 1.) process mapping activity - aimed at reducing variability in the energy auditing and energy modeling process. 2.) survey analysis -- To examine the misalignment between how industry members use the top energy modeling tools compared to their intended use as defined by software representatives. 3.) sensitivity analysis -- analysis of the affect key energy modeling inputs are having on energy modeling analysis results. The initial three phases helped define the need for an improved energy audit approach that better aligns data collection with facility owners' needs and priorities. The initial three phases also assisted in the development of a multi-criteria decision support tool that incorporates a House of Quality approach to guide a pre-audit planning activity. For the fourth and final research phase explored the impacts and evaluation methods of a pre-audit planning activity using two comparative energy audits as case studies. In each case, an energy audit professionals was asked to complete an audit using their traditional methods along with an audit which involved them first

  17. Energy and process substitution in the frozen-food industry: geothermal energy and the retortable pouch

    Energy Technology Data Exchange (ETDEWEB)

    Stern, M.W.; Hanemann, W.M.; Eckhouse, K.

    1981-12-01

    An assessment is made of the possibilities of using geothermal energy and an aseptic retortable pouch in the food processing industry. The focus of the study is on the production of frozen broccoli in the Imperial Valley, California. Background information on the current status of the frozen food industry, the nature of geothermal energy as a potential substitute for conventional fossil fuels, and the engineering details of the retortable pouch process are covered. The analytical methodology by which the energy and process substitution were evaluated is described. A four-way comparison of the economics of the frozen product versus the pouched product and conventional fossil fuels versus geothermal energy was performed. A sensitivity analysis for the energy substitution was made and results are given. Results are summarized. (MCW)

  18. Representing Global Reactive Potential Energy Surfaces Using Gaussian Processes.

    Science.gov (United States)

    Kolb, Brian; Marshall, Paul; Zhao, Bin; Jiang, Bin; Guo, Hua

    2017-04-06

    Representation of multidimensional global potential energy surfaces suitable for spectral and dynamical calculations from high-level ab initio calculations remains a challenge. Here, we present a detailed study on constructing potential energy surfaces using a machine learning method, namely, Gaussian process regression. Tests for the 3A″ state of SH2, which facilitates the SH + H ↔ S(3P) + H2 abstraction reaction and the SH + H' ↔ SH' + H exchange reaction, suggest that the Gaussian process is capable of providing a reasonable potential energy surface with a small number (∼1 × 102) of ab initio points, but it needs substantially more points (∼1 × 103) to converge reaction probabilities. The implications of these observations for construction of potential energy surfaces are discussed.

  19. Most critical collimator-mask-magnet sequence in the SPS-to-LHC transfer lines: energy deposition study.

    CERN Document Server

    Marzo, Matteo; Lechner, Anton; Vlachoudis, Vasilis

    2017-01-01

    This technical note refers to a study on the relation between the impact conditions of the SPS 450GeV proton beam and the energy deposited downstream the Target Collimator Dump In- jection Long (TCDIL) collimators [1], in the SPS-to-LHC transfer lines TI2 and TI8. Such an analysis is relevant in order to simulate the worst scenario of failure, in case the beam impacts on the TCDIL collimator’s jaw, in the frame of the LHC Injectors Upgrade (LIU), in view of the High Luminosity LHC (HL-LHC) phase. Previous studies already showed the dependency of the energy deposited in the downstream masks on the collimators-masks distance [2]. In absence of a (realistic) impact parameter, we perform now a study to select the most pessimistic one, trying to understand the origin of the various components responsible for the energy deposition on the downstream mask and magnet. The set up of the Monte Carlo FLUKA [3] [4] simulations and the most relevant results will be presented in this document. A sensitivity analysis was a...

  20. Statistical comparison of the ionospheric energy deposition before and after sudden enhancements in solar wind dynamic pressure using AMIE output

    Science.gov (United States)

    Boudouridis, A.; Kim, H.; Lyons, L. R.; Zesta, E.; Ridley, A. J.; Weygand, J. M.

    2011-12-01

    The solar wind dynamic pressure, both through its steady state value and through its variations, plays an important role in the determination of the state of the terrestrial magnetosphere and ionosphere, its effects being only secondary to those of the Interplanetary Magnetic Field (IMF). The solar wind dynamic pressure value is routinely included in various magnetospheric and ionospheric models as input. Recent studies have demonstrated the significant effect solar wind dynamic pressure enhancements have on the aurora, the field-aligned currents, the size of the polar cap, and the ionospheric convection and the transpolar potential. We present statistical studies of the ionospheric energy deposition during steady solar wind pressure conditions, and before and after sudden enhancements in solar wind pressure. We use five years of output from the Assimilative Mapping of Ionospheric Electrodynamics (AMIE) technique. The AMIE output consists of 1-min resolution values of the transpolar potential, the Hemispheric Power (a measure of auroral precipitation strength), and the ionospheric Joule heating. We find that the ionospheric energy deposition has the expected dependence on solar wind pressure and the IMF during steady conditions, increasing with increasing pressure and southward magnitude of the IMF. However, after solar wind pressure fronts there is additional enhancement of all AMIE parameters, indicating increased energy deposition on the terrestrial ionosphere. The increased ionospheric input lasts for 1-2 hours and then slowly dissipates, even though the solar wind pressure remains high, suggesting that the increased response of the ionosphere is transient in nature.

  1. Computer simulation of energy use, greenhouse gas emissions, and process economics of the fluid milk process.

    Science.gov (United States)

    Tomasula, P M; Yee, W C F; McAloon, A J; Nutter, D W; Bonnaillie, L M

    2013-05-01

    Energy-savings measures have been implemented in fluid milk plants to lower energy costs and the energy-related carbon dioxide (CO2) emissions. Although these measures have resulted in reductions in steam, electricity, compressed air, and refrigeration use of up to 30%, a benchmarking framework is necessary to examine the implementation of process-specific measures that would lower energy use, costs, and CO2 emissions even further. In this study, using information provided by the dairy industry and equipment vendors, a customizable model of the fluid milk process was developed for use in process design software to benchmark the electrical and fuel energy consumption and CO2 emissions of current processes. It may also be used to test the feasibility of new processing concepts to lower energy and CO2 emissions with calculation of new capital and operating costs. The accuracy of the model in predicting total energy usage of the entire fluid milk process and the pasteurization step was validated using available literature and industry energy data. Computer simulation of small (40.0 million L/yr), medium (113.6 million L/yr), and large (227.1 million L/yr) processing plants predicted the carbon footprint of milk, defined as grams of CO2 equivalents (CO2e) per kilogram of packaged milk, to within 5% of the value of 96 g of CO 2e/kg of packaged milk obtained in an industry-conducted life cycle assessment and also showed, in agreement with the same study, that plant size had no effect on the carbon footprint of milk but that larger plants were more cost effective in producing milk. Analysis of the pasteurization step showed that increasing the percentage regeneration of the pasteurizer from 90 to 96% would lower its thermal energy use by almost 60% and that implementation of partial homogenization would lower electrical energy use and CO2e emissions of homogenization by 82 and 5.4%, respectively. It was also demonstrated that implementation of steps to lower non-process

  2. Radial transport processes as a precursor to particle deposition in drinking water distribution systems.

    Science.gov (United States)

    van Thienen, P; Vreeburg, J H G; Blokker, E J M

    2011-02-01

    Various particle transport mechanisms play a role in the build-up of discoloration potential in drinking water distribution networks. In order to enhance our understanding of and ability to predict this build-up, it is essential to recognize and understand their role. Gravitational settling with drag has primarily been considered in this context. However, since flow in water distribution pipes is nearly always in the turbulent regime, turbulent processes should be considered also. In addition to these, single particle effects and forces may affect radial particle transport. In this work, we present an application of a previously published turbulent particle deposition theory to conditions relevant for drinking water distribution systems. We predict quantitatively under which conditions turbophoresis, including the virtual mass effect, the Saffman lift force, and the Magnus force may contribute significantly to sediment transport in radial direction and compare these results to experimental observations. The contribution of turbophoresis is mostly limited to large particles (>50 μm) in transport mains, and not expected to play a major role in distribution mains. The Saffman lift force may enhance this process to some degree. The Magnus force is not expected to play any significant role in drinking water distribution systems. © 2010 Elsevier Ltd. All rights reserved.

  3. In-situ monitoring of plasma ion assisted deposition (PIAD) processes

    Science.gov (United States)

    Harhausen, Jens; Foest, Rüdiger; Loffhagen, Detlef

    2015-09-01

    Present photonics applications depend on accurate production techniques. Plasma based processes might be termed the backbone of multilayer optical coatings which are the key components of dielectric mirrors, filters or antireflectives. However, the sector strongly relies on process recipies based on empirical optimization of thin film properties. Limitations in quality, repeatability and yield are faced. In this contribution results of efforts on plasma characterization of a beam source employed for PIAD are presented. Data on electron and ion kinetics as well as optical emission facilitated a comprehensive understanding of underlying physics of ion beam generation and propagation in an industrial type batch coater. In order to promote the development of next generation production plants, concepts for in-situ diagnostics are investigated. Results from monitoring of optical radiance of the plasma plume near the source and electron density near the substrates are discussed. The novel concept of the multipole resonance probe is applied during deposition in order to trace variations not only in magnitude of plasma density, but also its spatial distribution. Coating materials comprise TiO2, Ta2O5, Al2O3 and SiO2. Funded by the German Federal Ministry of Education and Research (BMBF) under Grant 13N13213).

  4. Simultaneous Counter-Ion Co-Deposition a Technique Enabling Matrix Isolation Spectroscopy Studies Using Low-Energy Beams of Mass-Selected Ions

    Science.gov (United States)

    Ludwig, Ryan M.; Moore, David T.

    2014-06-01

    Matrix isolation spectroscopy was first developed in Pimentel's group during the 1950's to facilitate spectroscopic studies of transient species. Cryogenic matrices of condensed rare gases provide an inert chemical environment with facile energy dissipation and are transparent at all wavelengths longer than vacuum UV, making them ideal for studying labile and reactive species such as radicals, weakly bound complexes, and ions. Since frozen rare gases are poor electrolytes, studies of ions require near-equal populations of anions and cations in order to stabilize the number densities required for spectroscopic experiments. Many techniques for generation of ions for using in matrix isolation studies satisfy this criterion intrinsically, however when ion beams generated in external sources are deposited, the counter-ions typically arise via secondary processes that are at best loosely controlled. It has long been recognized that it would be desirable to stabilize deposition of mass-selected ions generated in an external source using simultaneous co-deposition of a beam of counter-ions, however previous attempts to achieve this have been reported as unsuccessful. The Moore group at Lehigh has demonstrated successful experiments of this type, using mass-selected anions generated from a metal cluster source, co-deposited with a balanced current of cations generated in a separate electron ionization source. This talk will focus on the details of the technique, and present some results from proof-of-concept studies on anionic copper carbonyl complexes formed in argon matrices following co-deposition of Cu- with Ar+ or Kr+. Funding support from NSF CAREER Award CHE-0955637 is gratefully acknowledged. Whittle et al., J. Chem. Phys. 22, p.1943 (1954); Becker et al., J. Chem. Phys. 25, p.224 (1956). Godbout et al., J. Chem. Phys. 96, p.2892 (1996). Sabo et al., Appl. Spectrosc. 45, p. 535 (1991).

  5. Biological Effects of Particles with Very High Energy Deposition on Mammalian Cells Utilizing the Brookhaven Tandem Van de Graaff Accelerator

    Science.gov (United States)

    Saha, Janapriya; Cucinotta, Francis A.; Wang, Minli

    2013-01-01

    High LET radiation from GCR (Galactic Cosmic Rays) consisting mainly of high charge and energy (HZE) nuclei and secondary protons and neutrons, and secondaries from protons in SPE (Solar Particle Event) pose a major health risk to astronauts due to induction of DNA damage and oxidative stress. Experiments with high energy particles mimicking the space environment for estimation of radiation risk are being performed at NASA Space Radiation Laboratory at BNL. Experiments with low energy particles comparing to high energy particles of similar LET are of interest for investigation of the role of track structure on biological effects. For this purpose, we report results utilizing the Tandem Van de Graaff accelerator at BNL. The primary objective of our studies is to elucidate the influence of high vs low energy deposition on track structure, delta ray contribution and resulting biological responses. These low energy ions are of special relevance as these energies may occur following absorption through the spacecraft and shielding materials in human tissues and nuclear fragments produced in tissues by high energy protons and neutrons. This study will help to verify the efficiency of these low energy particles and better understand how various cell types respond to them.

  6. A NOVEL OPTIMIZED ENERGY-SAVING EXTRACTION PROCESS ON COFFEE

    Directory of Open Access Journals (Sweden)

    Cheng-Chi Wang

    2011-01-01

    Full Text Available In this paper, Taguchi method is applied to optimize ultrasound thermal process for extracting caffeine and flavor from coffee. The use of ultrasound can abridge experiments in cost, energy loss and time; the different operating conditions for extraction experiments are executed and the results are also compared. The results show that the best design factors for caffeine are 95℃ of extraction temperature, 28 kHz of operating frequency and 30 s of extraction time. The proposed optimized extraction method is efficient and energy-saving compared with the general process for making coffee.

  7. Effect of deposition speed on the flatness and cylindricity of parts produced by three dimensional printing process

    Science.gov (United States)

    Fahad, Muhammad; Khalid, Mahmood; Nauman, Muhammad; Khan, Maqsood Ahmed

    2017-08-01

    The idea of layer-by-layer deposition of materials to obtain three dimensional shapes, known as three dimensional printing, has gained much popularity during the last decade. Investigations related to understanding the effect of process parameters on the output of the accuracy of parts produced by three dimensional printing processes have been performed by various researchers. This study is also aimed at investigating the effect of deposition speed on the accuracy in terms of geometric dimensions and tolerancing such as flatness and cylindricity of the parts produced by open source three dimensional printers. The repeatability of the parts printed were also investigated.

  8. Different types of nitrogen deposition show variable effects on the soil carbon cycle process of temperate forests.

    Science.gov (United States)

    Du, Yuhan; Guo, Peng; Liu, Jianqiu; Wang, Chunyu; Yang, Ning; Jiao, Zhenxia

    2014-10-01

    Nitrogen (N) deposition significantly affects the soil carbon (C) cycle process of forests. However, the influence of different types of N on it still remained unclear. In this work, ammonium nitrate was selected as an inorganic N (IN) source, while urea and glycine were chosen as organic N (ON) sources. Different ratios of IN to ON (1 : 4, 2 : 3, 3 : 2, 4 : 1, and 5 : 0) were mixed with equal total amounts and then used to fertilize temperate forest soils for 2 years. Results showed that IN deposition inhibited soil C cycle processes, such as soil respiration, soil organic C decomposition, and enzymatic activities, and induced the accumulation of recalcitrant organic C. By contrast, ON deposition promoted these processes. Addition of ON also resulted in accelerated transformation of recalcitrant compounds into labile compounds and increased CO2 efflux. Meanwhile, greater ON deposition may convert C sequestration in forest soils into C source. These results indicated the importance of the IN to ON ratio in controlling the soil C cycle, which can consequently change the ecological effect of N deposition. © 2014 John Wiley & Sons Ltd.

  9. Processing of CuInSe2-Based Solar Cells: Characterization of Deposition Processes in Terms of Chemical Reaction Analyses. Final Report, 6 May 1995 - 31 December 1998

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, T.J.; Stanbery, B.J.

    2001-07-16

    This project describes a novel rotating-disc reactor has been designed and built to enable modulated flux deposition of CuInSe2 and its related binary compounds. The reactor incorporates both a thermally activated source and a novel plasma-activated source of selenium vapor, which have been used for the growth of epitaxial and polycrystalline thin-film layers of CuInSe2. A comparison of the different selenium reactant sources has shown evidence of increases in its incorporation when using the plasma source, but no measurable change when the thermally activated source was used. We concluded that the chemical reactivity of selenium vapor from the plasma source is significantly greater than that provided by the other sources studied. Epitaxially grown CuInSe2 layers on GaAs, ZnTe, and SrF2 demonstrate the importance of nucleation effects on the morphology and crystallographic structure of the resulting materials. These studies have resulted in the first reported growth of the CuAu type-I crystallographic polytype of CuInSe2, and the first reported epitaxial growth of CuInSe2 on ZnTe. Polycrystalline binary (Cu,Se) and (In,Se) thin films have been grown, and the molar flux ratio of selenium to metals was varied. It is shown that all of the reported binary compounds in each of the corresponding binary phase fields can be synthesized by the modulated flux deposition technique implemented in the reactor by controlling this ratio and the substrate temperature. These results were employed to deposit bilayer thin films of specific (Cu,Se) and (In,Se) compounds with low melting-point temperature, which were used to verify the feasibility of synthesizing CuInSe2 by subsequent rapid-thermal processing. The studies of the influence of sodium during the initial stages of epitaxy have led to a new model to explain its influences based on the hypothesis that it behaves as a surfactant in the Cu-In-Se material system. This represents the first unified theory on the role of sodium

  10. Oxidation of ZnO thin films during pulsed laser deposition process

    Indian Academy of Sciences (India)

    1CICATA-Instituto Politécnico Nacional, Altamira 89600, México. 2INESC Porto, Rua do Campo Alegre, 687, 4169-007 Porto, Portugal. 3School of Physics, Trinity College, Dublin 2, Ireland. MS received 1 March 2012. Abstract. Pulsed laser deposition of ZnO thin films, using KrF laser, is analysed. The films were deposited ...

  11. Biogeometallurgical pre-mining characterization of ore deposits: an approach to increase sustainability in the mining process.

    Science.gov (United States)

    Dold, Bernhard; Weibel, Leyla

    2013-11-01

    Based on the knowledge obtained from acid mine drainage formation in mine waste environments (tailings impoundments and waste rock dumps), a new methodology is applied to characterize new ore deposits before exploitation starts. This gives the opportunity to design optimized processes for metal recovery of the different mineral assemblages in an ore deposit and at the same time to minimize the environmental impact and costs downstream for mine waste management. Additionally, the whole economic potential is evaluated including strategic elements. The methodology integrates high-resolution geochemistry by sequential extractions and quantitative mineralogy in combination with kinetic bioleach tests. The produced data set allows to define biogeometallurgical units in the ore deposit and to predict the behavior of each element, economically or environmentally relevant, along the mining process.

  12. The SiNx films process research by plasma-enhanced chemical vapor deposition in crystalline silicon solar cells

    Science.gov (United States)

    Chen, Bitao; Zhang, Yingke; Ouyang, Qiuping; Chen, Fei; Zhan, Xinghua; Gao, Wei

    2017-07-01

    SiNx thin film has been widely used in crystalline silicon solar cell production because of the good anti-reflection and passivation effect. We can effectively optimize the cells performance by plasma-enhanced chemical vapor deposition (PECVD) method to change deposition conditions such as temperature, gas flow ratio, etc. In this paper, we deposit a new layer of SiNx thin film on the basis of double-layers process. By changing the process parameters, the compactness of thin films is improved effectively. The NH3 passivation technology is augmented in a creative way, which improves the minority carrier lifetime. In sight of this, a significant increase is generated in the photoelectric performance of crystalline silicon solar cell.

  13. Design and Operation of an Optically-Accessible Modular Reactor for Diagnostics of Thermal Thin Film Deposition Processes

    Science.gov (United States)

    Kimes, W. A.; Sperling, B. A.; Maslars, J. E.

    2015-01-01

    The design and operation of a simple, optically-accessible modular reactor for probing thermal thin film deposition processes, such as atomic layer deposition processes (ALD) and chemical vapor deposition (CVD), is described. This reactor has a nominal footprint of 225 cm2 and a mass of approximately 6.6 kg, making it small enough to conveniently function as a modular component of an optical train. The design is simple, making fabrication straightforward and relatively inexpensive. Reactor operation is characterized using two infrared absorption measurements to determine exhaust times for tetrakis(dimethylamino)titanium and water, proto-typical ALD precursors, in a pressure and flow regime commonly used for ALD. PMID:26958438

  14. Development of electrostatic supercapacitors by atomic layer deposition on nanoporous anodic aluminium oxides for energy harvesting applications

    Directory of Open Access Journals (Sweden)

    Lucia eIglesias

    2015-03-01

    Full Text Available Nanomaterials can provide innovative solutions for solving the usual energy harvesting and storage drawbacks that take place in conventional energy storage devices based on batteries or electrolytic capacitors, because they are not fully capable for attending the fast energy demands and high power densities required in many of present applications. Here, we report on the development and characterization of novel electrostatic supercapacitors made by conformal Atomic Layer Deposition on the high open surface of nanoporous anodic alumina membranes employed as templates. The structure of the designed electrostatic supercapacitor prototype consists of successive layers of Aluminium doped Zinc Oxide, as the bottom and top electrodes, together Al2O3 as the intermediate dielectric layer. The conformality of the deposited conductive and dielectric layers, together with their composition and crystalline structure have been checked by XRD and electron microscopy techniques. Impedance measurements performed for the optimized electrostatic supercapacitor device give a high capacitance value of 200 µF/cm2 at the frequency of 40 Hz, which confirms the theoretical estimations for such kind of prototypes, and the leakage current reaches values around of 1.8 mA/cm2 at 1 V. The high capacitance value achieved by the supercapacitor prototype together its small size turns these devices in outstanding candidates for using in energy harvesting and storage applications.

  15. Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

    Science.gov (United States)

    Yan, Ning; Qin, Lijun; Hao, Haixia; Hui, Longfei; Zhao, Fengqi; Feng, Hao

    2017-06-01

    Nanocomposites consisting of iron oxide (Fe2O3) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe2O3 was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe2O3 energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe2O3 composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe2O3 nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe2O3 nanoparticles. The enhanced energy release of rGO/Al@Fe2O3 is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe2O3 composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

  16. Simulation of Powder Layer Deposition in Additive Manufacturing Processes Using the Discrete Element Method

    Energy Technology Data Exchange (ETDEWEB)

    Herbold, E. B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Walton, O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Homel, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-10-26

    This document serves as a final report to a small effort where several improvements were added to a LLNL code GEODYN-­L to develop Discrete Element Method (DEM) algorithms coupled to Lagrangian Finite Element (FE) solvers to investigate powder-­bed formation problems for additive manufacturing. The results from these simulations will be assessed for inclusion as the initial conditions for Direct Metal Laser Sintering (DMLS) simulations performed with ALE3D. The algorithms were written and performed on parallel computing platforms at LLNL. The total funding level was 3-­4 weeks of an FTE split amongst two staff scientists and one post-­doc. The DEM simulations emulated, as much as was feasible, the physical process of depositing a new layer of powder over a bed of existing powder. The DEM simulations utilized truncated size distributions spanning realistic size ranges with a size distribution profile consistent with realistic sample set. A minimum simulation sample size on the order of 40-­particles square by 10-­particles deep was utilized in these scoping studies in order to evaluate the potential effects of size segregation variation with distance displaced in front of a screed blade. A reasonable method for evaluating the problem was developed and validated. Several simulations were performed to show the viability of the approach. Future investigations will focus on running various simulations investigating powder particle sizing and screen geometries.

  17. Impact of the Fused Deposition (FDM Printing Process on Polylactic Acid (PLA Chemistry and Structure

    Directory of Open Access Journals (Sweden)

    Michael Arthur Cuiffo

    2017-06-01

    Full Text Available Polylactic acid (PLA is an organic polymer commonly used in fused deposition (FDM printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier transform infrared (FTIR spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning electron microscopy (SEM and differential scanning calorimetry (DSC were used to characterize morphology, cold crystallinity, and the glass transition and melting temperatures following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro- and submicron-scale roughness that will also impact potential applications.

  18. A study of color modulation of porous alumina processed by physical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xulongqi; Zhang Haijun; Zhang Dongxian, E-mail: zhangdx@zju.edu.cn [State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou, 310027 (China)

    2011-02-01

    With the development of the porous alumina (PA) fabrication technology, more and more scholars plough into the research of its properties, especially optical properties. Recently, we observed an interesting phenomenon that the PA templates processed by Physical Vapor Deposition (PVD) show color differences related to light path difference. Our work attempts to make the principle clear and to find an effective method to modulate the color of PA samples. This article describes the details of our experimental and theoretical results. We successfully prepared some PA templates with different pore-depth by controlling the time of anodization in oxalic acid solution. In order to enhance the reflectivity of air-PA interface, a layer of TiO{sub 2} film of 18 nm is coated with PVD technique, which makes PA templates display quite distinct colors with different hole-depth. By modelling and analyzing PA samples, we make the interpretation of this optical property by taking the PA sample with 150 nm pore-depth as an example, and then put forward a way to simulate sample's color within its hole-depth and material refraction-index. The results are in good agreement with our theoretical analysis, which proves the feasibility of our simulation mode.

  19. Environmental sensing with optical fiber sensors processed with focused ion beam and atomic layer deposition

    Science.gov (United States)

    Flores, Raquel; Janeiro, Ricardo; Dahlem, Marcus; Viegas, Jaime

    2015-03-01

    We report an optical fiber chemical sensor based on a focused ion beam processed optical fiber. The demonstrated sensor is based on a cavity formed onto a standard 1550 nm single-mode fiber by either chemical etching, focused ion beam milling (FIB) or femtosecond laser ablation, on which side channels are drilled by either ion beam milling or femtosecond laser irradiation. The encapsulation of the cavity is achieved by optimized fusion splicing onto a standard single or multimode fiber. The empty cavity can be used as semi-curved Fabry-Pérot resonator for gas or liquid sensing. Increased reflectivity of the formed cavity mirrors can be achieved with atomic layer deposition (ALD) of alternating metal oxides. For chemical selective optical sensors, we demonstrate the same FIB-formed cavity concept, but filled with different materials, such as polydimethylsiloxane (PDMS), poly(methyl methacrylate) (PMMA) which show selective swelling when immersed in different solvents. Finally, a reducing agent sensor based on a FIB formed cavity partially sealed by fusion splicing and coated with a thin ZnO layer by ALD is presented and the results discussed. Sensor interrogation is achieved with spectral or multi-channel intensity measurements.

  20. Holographic Read-Only Memory Fabricated by Deposition of Reflector after Writing Process with Aromatic Photopolymer Recording Layer

    Science.gov (United States)

    Ando, Toshio; Masaki, Kazuyoshi; Shimizu, Takehiro

    2010-08-01

    The deposition of reflector after writing (DRAW) process has been proposed for the fabrication of reflective-type holographic read-only memories. In the DRAW process, a reflector is deposited on a recording medium after signal writing, resulting in the reduction of noise holograms written by reflected beams from a reflector in the write process. Significant improvements are experimentally confirmed in read and write (R/W) performances in DRAW-processed holographic media. The combination of the DRAW process and an aromatic photopolymer recording material realizes low noise, high signal-to-noise ratio, and low symbol error rate characteristics at large multiplexing numbers up to 1020. In conventional reflective-type holographic media, ghost noise is superimposed on the readout signal, causing deterioration in R/W characteristics. The wave vector analyses clarify the mechanism by which the noise holograms are written and ghost noise is superimposed on the signal beam in the conventional media.

  1. Energy and environmental analysis of a rapeseed biorefinery conversion process

    DEFF Research Database (Denmark)

    Boldrin, Alessio; Balzan, Alberto; Astrup, Thomas Fruergaard

    2013-01-01

    positive effects on the greenhouse gases (GHG) footprint of the biorefinery system, with improvements in the range of 9 % to 29 %, depending on the considered alternative. The mass and energy balances showed the potential for improvement of straw treatment processes (hydrothermal pre-treatment and dark...

  2. Strategic investment of embodied energy during the architectural planning process

    NARCIS (Netherlands)

    Hildebrand, L.

    2014-01-01

    It is an interesting time in the building industry; for more than one decade sustainability is a planning parameter that essentially impacts construction related processes. Reduction of operational energy was initiated after the oil crisis and changed the type of construction by including heat

  3. Advanced Photonic Processes for Photovoltaic and Energy Storage Systems.

    Science.gov (United States)

    Sygletou, Maria; Petridis, Constantinos; Kymakis, Emmanuel; Stratakis, Emmanuel

    2017-10-01

    Solar-energy harvesting through photovoltaic (PV) conversion is the most promising technology for long-term renewable energy production. At the same time, significant progress has been made in the development of energy-storage (ES) systems, which are essential components within the cycle of energy generation, transmission, and usage. Toward commercial applications, the enhancement of the performance and competitiveness of PV and ES systems requires the adoption of precise, but simple and low-cost manufacturing solutions, compatible with large-scale and high-throughput production lines. Photonic processes enable cost-efficient, noncontact, highly precise, and selective engineering of materials via photothermal, photochemical, or photophysical routes. Laser-based processes, in particular, provide access to a plethora of processing parameters that can be tuned with a remarkably high degree of precision to enable innovative processing routes that cannot be attained by conventional approaches. The focus here is on the application of advanced light-driven approaches for the fabrication, as well as the synthesis, of materials and components relevant to PV and ES systems. Besides presenting recent advances on recent achievements, the existing limitations are outlined and future possibilities and emerging prospects discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Energy transfer process of anisothermal wall-bounded flows

    Energy Technology Data Exchange (ETDEWEB)

    Aulery, Frédéric, E-mail: frederic.aulery@gmail.com [PROMES CNRS – UPR 8521, Rambla de la Thermodynamique, Tecnosud, Perpignan (France); Toutant, Adrien [PROMES CNRS – UPR 8521, Rambla de la Thermodynamique, Tecnosud, Perpignan (France); Université de Perpignan Via Domitia, 52 avenue Paul Alduy, 66860 Perpignan Cedex 9 (France); Bataille, Françoise [PROMES CNRS – UPR 8521, Rambla de la Thermodynamique, Tecnosud, Perpignan (France); Florida State University, Department of Mathematics, Tallahassee, FL (United States); Zhou, Ye, E-mail: zhou3@llnl.gov [Lawrence Livermore National Laboratory, Livermore, CA (United States)

    2015-07-31

    Strong temperature gradients introduce a major external agency into the wall-bounded turbulent flows. In these flows, the temperature field and the turbulent velocity field are highly correlated. In fact, standard RANS turbulent models are not able to accurately reproduce these flows. In order to improve the performance of the models, we need to understand how the energy is produced, transferred, and dissipated in a strong anisothermal wall-bounded flow. This letter presents a first detailed investigation on the roles played by each contributor in the energy transfer equation. - Highlights: • Turbulent flows subject to high temperature gradients are considered. • The influence of the “temperature gradients” on the energy transfer process is determined. • Inverse energy cascade in an anisotropic flow is observed.

  5. Effects of substrate preheating during direct energy deposition on microstructure, hardness, tensile strength, and notch toughness

    Science.gov (United States)

    Baek, Gyeong Yun; Lee, Ki Yong; Park, Sang Hu; Shim, Do Sik

    2017-11-01

    This study examined the effects of substrate preheating for the hardfacing of cold-press dies using the high-speed tool steel AISI M4. The preheating of the substrate is a widely used technique for reducing the degree of thermal deformation and preventing crack formation. We investigated the changes in the metallurgical and mechanical properties of the high-speed tool steel M4 deposited on an AISI D2 substrate with changes in the substrate preheating temperature. Five preheating temperatures (100-500 °C; interval of 100 °C) were selected, and the changes in the temperature of the substrate during deposition were observed. As the preheating temperature of the substrate was increased, the temperature gradient between the melting layer and the substrate decreased; this prevented the formation of internal cracks, owing to thermal stress relief. Field-emission scanning electron microscopy showed that a dendritic structure was formed at the interface between the deposited layer and the substrate while a cellular microstructure was formed in the deposited layer. As the preheating temperature was increased, the sizes of the cells and precipitated carbides also increased. Furthermore, the hardness increased slightly while the strength and toughness decreased. Moreover, the tensile and impact properties deteriorated rapidly at excessively high preheating temperatures (greater than 500 °C). The results of this study can be used as preheating criteria for achieving the desired mechanical properties during the hardfacing of dies and molds.

  6. Effects of substrate preheating during direct energy deposition on microstructure, hardness, tensile strength, and notch toughness

    Science.gov (United States)

    Baek, Gyeong Yun; Lee, Ki Yong; Park, Sang Hu; Shim, Do Sik

    2017-10-01

    This study examined the effects of substrate preheating for the hardfacing of cold-press dies using the high-speed tool steel AISI M4. The preheating of the substrate is a widely used technique for reducing the degree of thermal deformation and preventing crack formation. We investigated the changes in the metallurgical and mechanical properties of the high-speed tool steel M4 deposited on an AISI D2 substrate with changes in the substrate preheating temperature. Five preheating temperatures (100-500 °C; interval of 100 °C) were selected, and the changes in the temperature of the substrate during deposition were observed. As the preheating temperature of the substrate was increased, the temperature gradient between the melting layer and the substrate decreased; this prevented the formation of internal cracks, owing to thermal stress relief. Field-emission scanning electron microscopy showed that a dendritic structure was formed at the interface between the deposited layer and the substrate while a cellular microstructure was formed in the deposited layer. As the preheating temperature was increased, the sizes of the cells and precipitated carbides also increased. Furthermore, the hardness increased slightly while the strength and toughness decreased. Moreover, the tensile and impact properties deteriorated rapidly at excessively high preheating temperatures (greater than 500 °C). The results of this study can be used as preheating criteria for achieving the desired mechanical properties during the hardfacing of dies and molds.

  7. The Impact of Process Scaling on Scratchpad Memory Energy Savings

    Directory of Open Access Journals (Sweden)

    Bennion Redd

    2014-09-01

    Full Text Available Scratchpad memories have been shown to reduce power consumption, but the different characteristics of nanometer scale processes, such as increased leakage power, motivate an examination of how the benefits of these memories change with process scaling. Process and application characteristics affect the amount of energy saved by a scratchpad memory. Increases in leakage as a percentage of total power particularly impact applications that rarely access memory. This study examines how the benefits of scratchpad memories have changed in newer processes, based on the measured performance of the WIMS (Wireless Integrated MicroSystems microcontroller implemented in 180- and 65-nm processes and upon simulations of this microcontroller implemented in a 32-nm process. The results demonstrate that scratchpad memories will continue to improve the power dissipation of many applications, given the leakage anticipated in the foreseeable future.

  8. Method for evaluating the potential of geothermal energy in industrial process heat applications

    Energy Technology Data Exchange (ETDEWEB)

    Packer, M.B.; Mikic, B.B.; Meal, H.C., Guillamon-Duch, H.

    1980-05-01

    A method is presented for evaluating the technical and economic potential of geothermal energy for industrial process heat applications. The core of the method is a computer program which can be operated either as a design analysis tool to match energy supplies and demands, or as an economic analysis tool if a particular design for the facility has already been selected. Two examples are given to illustrate the functioning of the model and to demonstrate that results reached by use of the model closely parallel those that have been determined by more traditional techniques. Other features of interest in the model include: (1) use of decision analysis techniques as well as classical methods to deal with questions relating optimization; (2) a tax analysis of current regulations governing percentage depletion for geothermal deposits; and (3) development of simplified correlations for the thermodynamic properties of salt solutions in water.

  9. Analytical model of ionization and energy deposition by proton beams in subcellular compartments

    Science.gov (United States)

    de Vera, Pablo; Surdutovich, Eugene; Abril, Isabel; Garcia-Molina, Rafael; Solov'yov, Andrey V.

    2014-04-01

    We present an analytical model to evaluate in a fast, simple and effective manner the energy delivered by proton beams moving through a cell model made of nucleus and cytoplasm, taking into account the energy carried by the secondary electrons generated along the proton tracks. The electronic excitation spectra of these subcellular compartments have been modelled by means of an empirical parameterization of their dielectric properties. The energy loss rate and target ionization probability induced by swift protons are evaluated by means of the dielectric formalism. With the present model we have quantified the energy delivered, the specific energy, and the number of ionizations produced per incoming ion in a typical human cell by a typical hadrontherapy proton beam having energies usually reached around the Bragg peak (below 20 MeV). We find that the specific energy per incoming ion delivered in the nucleus and in the cytoplasm are rather similar for all the proton energy range analyzed.

  10. Biorefineries to integrate fuel, energy and chemical production processes

    Directory of Open Access Journals (Sweden)

    Enrica Bargiacchi

    2007-12-01

    Full Text Available The world of renewable energies is in fast evolution and arouses political and public interests, especially as an opportunity to boost environmental sustainability by mitigation of greenhouse gas emissions. This work aims at examining the possibilities related to the development of biorefineries, where biomass conversion processes to produce biofuels, electricity and biochemicals are integrated. Particular interest is given to the production processes of biodiesel, bioethanol and biogas, for which present world situation, problems, and perspectives are drawn. Potential areas for agronomic and biotech researches are also discussed. Producing biomass for biorefinery processing will eventually lead to maximize yields, in the non food agriculture.

  11. Processing and characterization of multilayers for energy device fabrication (invited)

    DEFF Research Database (Denmark)

    Kaiser, Andreas; Kiebach, Wolff-Ragnar; Gurauskis, Jonas

    SOFC and tubular OTM, we present selected challenges in ceramic processing such asymmetric multilayer structures. By optimizing different steps in the ceramic processing, we improved the mechanical properties and gas permeability of porous supports and the (electrochemical) performance of electrodes/catalytic...... allows the minimization of sintering stresses, thereby avoiding the formation of defects, such as camber, delamination or crack formation. We briefly highlight recent activities at DTU Energy with advanced processing techniques, such as using electrospinning and 3D printing in fabrication of multilayers....

  12. Surface Energy and Setting Process of Contacting Surfaces

    Directory of Open Access Journals (Sweden)

    M. V. Musokhranov

    2014-01-01

    Full Text Available The paper deals with a challenge in terms of ensuring an accuracy of the relative position of the conjugated surfaces that is to determine a coefficient of friction. To solve it, there is a proposal to use the surface energy, as a tool that influences the contacting parts nature. Presently, energy of the surface layers at best is only stated, but not used in practice.Analysis of the conditions of interaction between two contacting surfaces, such as seizing and setting cannot be explained only from the position of the roughness parameters. It is found that these phenomena are explained by the appearing gripe (setting bridges, which result from the energy of interaction between two or more adjacent surfaces. The emerging phenomenon such as micro welding, i.e. occurring bonds, is caused by the overflow of energy, according to the theory of physics, from the surface with a high level of energy to the surface with the smaller one to balance the system as a whole.The paper shows that through the use of process, controlling the depth of the surface layer and creating a certain structure, the energy level of the material as a whole can be specified. And this will allow us to provide the necessary performance and mechanical properties. It means to create as many gripe bridges as possible to ensure continuous positioning i.e. a fixed connection of the contacting surfaces.It was determined that to increase a value of the friction coefficient, the physical and mechanical properties of the surface layer of the parts material must be taken into account, namely, in the part body accumulate the energy to be consumed for forming the surface.The paper gives recommendations for including the parts of the surface energy in the qualitative indicators of characteristics. This will make a technologist, when routing a process, to choose such operations and modes to provide the designer-specified parameters not only of the accuracy and surface finish, but also of the

  13. The inorganic route to the low temperature chemical vapor deposition of TiN for ultra large scale integration technologies: Process and material development and characterization

    Science.gov (United States)

    Faltermeier, Cheryl Gail

    1997-11-01

    The demand for computers with more functionality, more memory, and higher speed are the major factors affecting the design of computer chips. This demand for increased capacity is expected to continue for the foreseeable future. In order to meet these demands, new material processes must be developed for computer chip fabrication. This thesis focuses on the identification, development, and optimization of a novel approach to a low temperature ({process for the deposition of TiN diffusion barrier liners for ULSI applications using the inorganic halide tetraiodotitanium, TiIsb4, as the source precursor. Correspondingly, Chapter 2 concentrated on establishing a fundamental understanding of precursor decomposition pathways and associated film nucleation and growth kinetics. As part of the study, key process parameters were varied systematically in order to establish functionality curves for film purity, growth rate, structure, and morphology. In the identified optimum process window, the TiN films were nitrogen-rich, with iodine concentrations below 2 at%, displayed resistivities in the range 100-150 muOmega-cm depending on thickness, and exhibited excellent step coverage-with better than 90% conformality in both nominal 0.45 mum, 3:1 aspect ratio and 0.25 mum, 4:1 aspect ratio contact structures. Chapter 3 describes and discusses mechanistic studies which used the profile emulator Stanford Profile Emulator for Etching and Deposition in IC Engineering (SPEEDIE) in combination with specialized cantilever structures. The purpose was to determine the underlying mechanisms (direct deposition, re-emission, and surface diffusion) which control the deposition profiles of TiN in steps, trenches, and via holes. Corresponding sticking coefficients were subsequently established for different process windows, and optimum processing conditions were identified for conformal step coverage in sub-quarter-micron device structures. In Chapter 4, the performance of TiN as diffusion

  14. Combined Energy Supply System for Meat Processing Plants

    Directory of Open Access Journals (Sweden)

    Sit M.

    2015-04-01

    Full Text Available The purpose of this study is the development of technological schemes of energy production for this industry in terms of energy efficiency. Technical solution that can reduce cost of the final production of meat production plant has been presented. The main idea of the tehnical solution is the use of turboexpander, which must be installed on gas reduction station near meat processing plant in the packet with the „air-water” gas – driven heat pump, which gas cooler serves as gas heating unit for the first stage of turboexpander. The thermal exit of gas engine serves as gas heating unit for the second stage of turboexpander and as heat energy generator for the plant and source of the heat for one of the evaporators of heat pump, as well. The second evaporator of heat pump is connected with the cold consuming equipment of the plant. The electric energy, which is produced by gas engine is consumed by heat pump compressor and electric equipment of the plant. Electric energy, which is produced by turbo expander is transmitted to the electric grid. The proposed technical solution can be used to reduce natural gas consumption on meat processing plants and the cost of production of electricity, heat and cold.

  15. Tolerance of Three-Stage CIGS Deposition to Variations Imposed by Roll-to-Roll Processing: Phase II Annual Report, May 2003--May 2004

    Energy Technology Data Exchange (ETDEWEB)

    Beck, M. E.; Repins, I. L.

    2004-07-01

    Global Solar Energy, Inc. (GSE) and lower-tier subcontractor ITN Energy Systems, Inc. (ITN) are addressing process tolerance issues in this program. The definition and resolution of process tolerance issues satisfy many of the goals of the Thin Film Photovoltaics Partnerships Program (TFPPP). First, the investigation is likely to identify acceptable ranges for critical deposition parameters. This will have the benefit of providing upper and lower control limits for in-situ process monitoring components, thus increasing average efficiency as well as yield of product. Second, the exploration may uncover insensitivities to some processing procedures, allowing manufacture of modules at increased throughput and decreased cost. The exploration allows a quantitative evaluation of the trade-offs between performance, throughput, and costs. Third, the proposed program also satisfies the TFPPP goal of establishing a wider research and development base for higher-efficiency processing. Four th, the acquisition of data defining sensitivity to processing has important implications for the required accuracy of process sensors and control. Finally, the program helps the photovoltaic community advance toward a better understanding of CIGS growth, a longer-term goal of the TFPPP.

  16. Tolerance of Three-Stage CIGS Deposition to Variations Imposed by Roll-to-Roll Processing: Phase I Annual Report, May 2002--May 2003

    Energy Technology Data Exchange (ETDEWEB)

    Beck, M. E.; Repins, I. L.

    2003-06-01

    Global Solar Energy, Inc. (GSE) and subcontractor ITN Energy Systems, Inc. (ITN) are addressing process tolerance issues in this program. The definition and resolution of process tolerance issues satisfy many of the goals of the Thin Film Photovoltaics Partnership Program (TFPPP). First, the investigation is likely to identify acceptable ranges for critical deposition parameters. This will have the benefit of providing upper and lower control limits for in-situ process-monitoring components, thus increasing average efficiency, as well as yield of product. Second, the exploration may uncover insensitivities to some processing procedures, allowing manufacture of modules at increased throughput and decreased cost. The exploration allows a quantitative evaluation of the trade-offs between performance, throughput, and costs. Third, the proposed program also satifies the TFPPP goal of establishing a wider research and development base for higher-efficiency processing. Fourth, the acquisition of data defining sensitivity to processing has important implications for the required accuracy of process sensors and control. Finally, the program helps the photovoltaic community advance toward a better understanding of CIGS growth, which is a longer-term goal of the TFPPP.

  17. Impact of residual by-products from tungsten film deposition on process integration due to nonuniformity of the tungsten film

    CERN Document Server

    Sidhwa, A; Gandy, T; Melosky, S; Brown, W; Ang, S; Naseem, H; Ulrich, R

    2002-01-01

    The effects of residual by products from a tungsten film deposition process and their impact on process integration due to the nonuniformity of the tungsten film were investigated in this work. The tungsten film deposition process involves three steps: nucleation, stabilization, and tungsten bulk fill. Six experiments were conducted in search for a solution to the problem. The resulting data suggest that excess nitrogen left in the chamber following the tungsten nucleation step, along with residual by products, causes a shift in the tungsten film uniformity during the tungsten bulk fill process. Data reveal that, due to the residual by products, an abnormal grain growth occurs causing a variation in the tungsten thickness across the wafer during the bulk fill step. Although several possible solutions were revealed by the experiments, potential integration problems limited the acceptable solutions to one. The solution chosen was the introduction of a 10 s pumpdown immediately following the nucleation step. Thi...

  18. Low temperature sputter-deposited ZnO films with enhanced Hall mobility using excimer laser post-processing

    Science.gov (United States)

    Tsakonas, C.; Kuznetsov, V. L.; Cranton, W. M.; Kalfagiannis, N.; Abusabee, K. M.; Koutsogeorgis, D. C.; Abeywickrama, N.; Edwards, P. P.

    2017-12-01

    We report the low temperature (T  ZnO thin films (~140 nm) with Hall mobility of up to 17.3 cm2 V‑1 s‑1 making them suitable for thin film transistor (TFT) applications. The films were deposited by rf magnetron sputtering at T  V‑1 s‑1 at a carrier density of 2.3  ×  1018 cm‑3 was measured from a 1 GΩ as deposited and aged film after the laser treatment. We suggest that the aging of non-processed films reduces structural defects mainly at grain boundaries by air species chemisorption, with concomitant increase in thermal conductivity so that laser processing can have an enhancing effect. Such a processing combination can act synergistically and produce suitable active layers for TFT applications with low temperature processing requirements.

  19. Nanocrystalline ZnO thin film deposition on flexible substrate by low-temperature sputtering process for plastic displays.

    Science.gov (United States)

    Banerjee, Arghya Narayan; Joo, Sang Woo; Min, Bong-Ki

    2014-10-01

    A low temperature sputter deposition process is adopted to fabricate nanocrystalline ZnO thin films on plastic (polyethylene terepthalate) substrate. Very good crystalline films are synthesized at a substrate temperature around 120 degrees C. Structural and microstructural analyses confirm the proper phase formation of the nanomaterial with an average nanoparticle size around 5-10 nm. Optical transmission analysis of the film deposited on plastic substrate depicts nearly 90% visible transmittance with a direct bandgap around 3.56 eV. This cost-effective, low-temperature fabrication of nanocrystalline thin film with very good structural and optical properties will find important applications in plastic display technology. Also the process is a vacuum-based clean process, which is compatible to CMOS-IC fabrication techniques and therefore, can easily be integrated with modern solid state device fabrication processes for diverse device applications.

  20. Handbook of thin film deposition processes and techniques principles, methods, equipment and applications

    CERN Document Server

    Seshan, Krishna

    2002-01-01

    New second edition of the popular book on deposition (first edition by Klaus Schruegraf) for engineers, technicians, and plant personnel in the semiconductor and related industries. This book traces the technology behind the spectacular growth in the silicon semiconductor industry and the continued trend in miniaturization over the last 20 years. This growth has been fueled in large part by improved thin film deposition techniques and the development of highly specialized equipment to enable this deposition. The book includes much cutting-edge material. Entirely new chapters on contamination and contamination control describe the basics and the issues-as feature sizes shrink to sub-micron dimensions, cleanliness and particle elimination has to keep pace. A new chapter on metrology explains the growth of sophisticated, automatic tools capable of measuring thickness and spacing of sub-micron dimensions. The book also covers PVD, laser and e-beam assisted deposition, MBE, and ion beam methods to bring together a...

  1. Processing and Deposition of Nanocrystalline Oxide Composites for Thermal Barrier Coatings

    National Research Council Canada - National Science Library

    Ying, Jackie

    2000-01-01

    .... Electrophoretic deposition was used to coat the nanocomposite powders onto nickel substrates. The effect of alumina content, powder calcination temperature, and film thickness on the thermal stability of zirconia-based coatings was examined...

  2. Energy deposition by a {sup 106}Ru/{sup 106}Rh eye applicator simulated using LEPTS, a low-energy particle track simulation

    Energy Technology Data Exchange (ETDEWEB)

    Fuss, M.C. [Instituto de Fisica Fundamental, Consejo Superior de Investigaciones Cientificas (CSIC), Serrano 113-bis, 28006 Madrid (Spain); Munoz, A.; Oller, J.C. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avenida Complutense 22, 28040 Madrid (Spain); Blanco, F. [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad Complutense de Madrid, Avenida Complutense, 28040 Madrid (Spain); Williart, A. [Departamento de Fisica de los Materiales, Universidad Nacional de Educacion a Distancia, Senda del Rey 9, 28040 Madrid (Spain); Limao-Vieira, P. [Laboratorio de Colisoes Atomicas e Moleculares, Departamento de Fisica, CEFITEC, FCT-Universidade Nova de Lisboa, Quinta da Torre, 2829-516 Caparica (Portugal); Borge, M.J.G.; Tengblad, O. [Instituto de Estructura de la Materia, Consejo Superior de Investigaciones Cientificas (CSIC), Serrano 113-bis, 28006 Madrid (Spain); Huerga, C.; Tellez, M. [Hospital Universitario La Paz, Paseo de la Castellana 261, 28046 Madrid (Spain); Garcia, G., E-mail: g.garcia@iff.csic.es [Instituto de Fisica Fundamental, Consejo Superior de Investigaciones Cientificas (CSIC), Serrano 113-bis, 28006 Madrid (Spain); Departamento de Fisica de los Materiales, Universidad Nacional de Educacion a Distancia, Senda del Rey 9, 28040 Madrid (Spain)

    2011-09-15

    The present study introduces LEPTS, an event-by-event Monte Carlo programme, for simulating an ophthalmic {sup 106}Ru/{sup 106}Rh applicator relevant in brachytherapy of ocular tumours. The distinctive characteristics of this code are the underlying radiation-matter interaction models that distinguish elastic and several kinds of inelastic collisions, as well as the use of mostly experimental input data. Special emphasis is placed on the treatment of low-energy electrons for generally being responsible for the deposition of a large portion of the total energy imparted to matter. - Highlights: > We present the Monte Carlo code LEPTS, a low-energy particle track simulation. > Carefully selected input data from 10 keV to 1 eV. > Application to an electron emitting Ru-106/Rh-106 plaque used in brachytherapy.

  3. Electromagnetic energy deposition rate in the polar upper thermosphere derived from the EISCAT Svalbard radar and CUTLASS Finland radar observations

    Directory of Open Access Journals (Sweden)

    H. Fujiwara

    2007-11-01

    Full Text Available From simultaneous observations of the European incoherent scatter Svalbard radar (ESR and the Cooperative UK Twin Located Auroral Sounding System (CUTLASS Finland radar on 9 March 1999, we have derived the height distributions of the thermospheric heating rate at the F region height in association with electromagnetic energy inputs into the dayside polar cap/cusp region. The ESR and CUTLASS radar observations provide the ionospheric parameters with fine time-resolutions of a few minutes. Although the geomagnetic activity was rather moderate (Kp=3+~4, the electric field obtained from the ESR data sometimes shows values exceeding 40 mV/m. The estimated passive energy deposition rates are also larger than 150 W/kg in the upper thermosphere over the ESR site during the period of the enhanced electric field. In addition, enhancements of the Pedersen conductivity also contribute to heating the upper thermosphere, while there is only a small contribution for thermospheric heating from the direct particle heating due to soft particle precipitation in the dayside polar cap/cusp region. In the same period, the CUTLASS observations of the ion drift show the signature of poleward moving pulsed ionospheric flows with a recurrence rate of about 10–20 min. The estimated electromagnetic energy deposition rate shows the existence of the strong heat source in the dayside polar cap/cusp region of the upper thermosphere in association with the dayside magnetospheric phenomena of reconnections and flux transfer events.

  4. Plantwide Energy Assessment of a Sugarcane Farming and Processing Facility

    Energy Technology Data Exchange (ETDEWEB)

    Jakeway, L.A.; Turn, S.Q.; Keffer, V.I.; Kinoshita, C.M.

    2006-02-27

    A plantwide energy assessment was performed at Hawaiian Commercial & Sugar Co., an integrated sugarcane farming and processing facility on the island of Maui in the State of Hawaii. There were four main tasks performed for the plantwide energy assessment: 1) pump energy assessment in both field and factory operations, 2) steam generation assessment in the power production operations, 3) steam distribution assessment in the sugar manufacturing operation, and 4) electric power distribution assessment of the company system grid. The energy savings identified in each of these tasks were summarized in terms of fuel savings, electricity savings, or opportunity revenue that potentially exists mostly from increased electric power sales to the local electric utility. The results of this investigation revealed eight energy saving projects that can be implemented at HC&S. These eight projects were determined to have potential for $1.5 million in annual fuel savings or 22,337 MWh equivalent annual electricity savings. Most of the savings were derived from pump efficiency improvements and steam efficiency improvements both in generation and distribution. If all the energy saving projects were implemented and the energy savings were realized as less fuel consumed, there would be corresponding reductions in regulated air pollutants and carbon dioxide emissions from supplemental coal fuel. As HC&S is already a significant user of renewable biomass fuel for its operations, the projected reductions in air pollutants and emissions will not be as great compared to using only coal fuel for example. A classification of implementation priority into operations was performed for the identified energy saving projects based on payback period and ease of implementation.

  5. The energy saving research of the flat tire vulcanization process

    Science.gov (United States)

    Tang, X.; He, J.-Y.; Zhang, J. Y.; An, Y.; Yang, W.-M.; Tan, J.

    2015-07-01

    Vulcanization was an important step in tire production process, directly determining the mechanical properties of the tire which was the most energy-intensive link. The traditional vulcanization process of a flat tire did not consider the post curing effect, which may result in a waste of energy. Early finite element simulation showed that the traditional process caused excessive vulcanization. In order to find ways to improve the curing process, in the paper effect of process parameters on the flat tire vulcanization had been studied. Curing parameters included heating temperature, curing time and preheating temperature. Corresponding to these three factors, the three-dimensional model was established by ABAQUS finite element software to carry out three groups of simulation. Result showed that heat source temperature on the maximum temperature was the largest, effect of preheating temperature was the lowest; heat source temperature on the curing degree was the largest, effect of the curing time was lowest. According to the data analysis the optimal process parameters had been raised.

  6. Iron oxide/aluminum/graphene energetic nanocomposites synthesized by atomic layer deposition: Enhanced energy release and reduced electrostatic ignition hazard

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Ning; Qin, Lijun [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hao, Haixia [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Hui, Longfei [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Zhao, Fengqi [Science and Technology on Combustion and Explosion Laboratory, Xi’an Modern Chemistry Research Institute, Shaanxi (China); Feng, Hao, E-mail: fenghao98@hotmail.com [Laboratory of Material Surface Engineering and Nanofabrication, Xi’an Modern Chemistry Research Institute, Shaanxi (China); State Key Laboratory of Fluorine and Nitrogen Chemicals, Xi’an Modern Chemistry Research Institute, Shaanxi (China)

    2017-06-30

    Highlights: • Energetic rGO/Al@Fe{sub 2}O{sub 3}nanocompositeswerefabricatedbyatomiclayerdepositionapproach. • A novel Al@Fe{sub 2}O{sub 3} unit featuring core-shell structure was decorated on the graphene nanosheet. • RGO/Al@Fe{sub 2}O{sub 3} nanocomposite exhibits superior energy release and reduced electrostatic ignition hazard. - Abstract: Nanocomposites consisting of iron oxide (Fe{sub 2}O{sub 3}) and nano-sized aluminum (Al), possessing outstanding exothermic redox reaction characteristics, are highly promising nanothermite materials. However, the reactant diffusion inhibited in the solid state system makes the fast and complete energy release very challenging. In this work, Al nanoparticles anchored on graphene oxide (GO/Al) was initially prepared by a solution assembly approach. Fe{sub 2}O{sub 3} was deposited on GO/Al substrates by atomic layer deposition (ALD). Simultaneously thermal reduction of GO occurs, resulting in rGO/Al@Fe{sub 2}O{sub 3} energetic composites. Differential scanning calorimetry (DSC) analysis reveals that rGO/Al@Fe{sub 2}O{sub 3} composite containing 4.8 wt% of rGO exhibits a 50% increase of the energy release compared to the Al@Fe{sub 2}O{sub 3} nanothermite synthesized by ALD, and an increase of about 130% compared to a random mixture of rGO/Al/Fe{sub 2}O{sub 3} nanoparticles. The enhanced energy release of rGO/Al@Fe{sub 2}O{sub 3} is attributed to the improved spatial distribution as well as the increased interfacial intimacy between the oxidizer and the fuel. Moreover, the rGO/Al@Fe{sub 2}O{sub 3} composite with an rGO content of 9.6 wt% exhibits significantly reduced electrostatic discharge sensitivity. These findings may inspire potential pathways for engineering energetic nanocomposites with enhanced energy release and improved safety characteristics.

  7. Process evaluation of the Regional Biomass Energy Program

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, C.R.; Brown, M.A.; Perlack, R.D.

    1994-03-01

    The U.S. Department of Energy (DOE) established the Regional Biomass Energy Program (RBEP) in 1983 to increase the production and use of biomass energy resources. Through the creation of five regional program (the Great Lakes, Northeast, Pacific Northwest, Southeast, and West), the RBEP focuses on regionally specific needs and opportunities. In 1992, Oak Ridge National (ORNL) conducted a process evaluation of the RBEP Program designed to document and explain the development of the goals and strategies of the five regional programs; describe the economic and market context surrounding commercialization of bioenergy systems; assess the criteria used to select projects; describe experiences with cost sharing; identify program accomplishments in the transfer of information and technology; and offer recommendations for program improvement.

  8. Urbanization Process and Variation of Energy Budget of Land Surfaces

    Directory of Open Access Journals (Sweden)

    Ciro Gardi

    Full Text Available Urban areas are increasing at a rate much higher than human population growth in many part of the world; actually more than 73 towns in the world are larger than 1000 km2. The European Environmental Agency indicates an urban area average growth rate, over the last 20 years, of 20%. The urbanization process, and the consequent soil sealing, determines not only the losses of the ecological functions of the soil, but also a variation of the energy budget of land surfaces, that affect the microclimatic conditions (heat islands. The alteration of the energy budget are determined by the variations of albedo and roughness of surfaces, but especially by the net losses of evapotranspirating areas. In the present research we have assessed the variation of Parma territory energy budget, induced by the change in land use over the last 122 years. The urban area increase between 1881 and 2003 was 535%.

  9. Energy landscape exploration of the folding processes of biological molecules

    Science.gov (United States)

    Engel, Megan Clare

    For decades, scientists from every discipline have struggled to understand the mechanism of biological self-assembly, which allows proteins and nucleic acids to fold reliably into functional three-dimensional structures. Such an understanding may hold the key to eliminating diseases such as Alzheimer's and Parkinson's and to effective protein engineering. The current best framework for describing biological folding processes is that of statistical mechanical energy landscape theory, and one of the most promising experimental techniques for exploring molecular energy landscapes is single molecule force spectroscopy (SMFS), in which molecules are mechanically denatured. Theoretical advances have enabled the extraction of complete energy landscape profiles from SMFS data. Here, SMFS experiments performed using laser optical tweezers are analyzed to yield the first ever full landscape profile for an RNA pseudoknot. Further, a promising novel landscape reconstruction technique is validated for the first time using experimental data from a DNA hairpin.

  10. Studies on Effect of Fused Deposition Modelling Process Parameters on Ultimate Tensile Strength and Dimensional Accuracy of Nylon

    Science.gov (United States)

    Basavaraj, C. K.; Vishwas, M.

    2016-09-01

    This paper discusses the process parameters for fused deposition modelling (FDM). Layer thickness, Orientation angle and shell thickness are the process variables considered for studies. Ultimate tensile strength, dimensional accuracy and manufacturing time are the response parameters. For number of experimental runs the taguchi's L9 orthogonal array is used. Taguchis S/N ratio was used to identify a set of process parameters which give good results for respective response characteristics. Effectiveness of each parameter is investigated by using analysis of variance. The material used for the studies of process parameter is Nylon.

  11. Simulation of Energy Savings in Automotive Coatings Processes

    Science.gov (United States)

    Gerini Romagnoli, Marco

    Recently, the automakers have become more and more aware of the environmental and economic impact of their manufacturing processes. The paint shop is the largest energy user in a vehicle manufacturing plant, and one way to reduce costs and energy usage is the optimization of this area. This project aims at providing a tool to model and simulate a paint shop, in order to run and analyze some scenarios and case studies, helping to take strategic decisions. Analytical computations and real data were merged to build a tool that can be used by FCA for their Sterling Heights plant. Convection and conduction heat losses were modeled for the dip processes and the ovens. Thermal balances were used to compute the consumptions of booths, decks and ovens, while pump and fan energy consumptions were modeled for each sub-process. The user acts on a calendar, scheduling a year of production, and the model predicts the energy consumption of the paint shop. Five scenarios were run to test different conditions and the influence of scheduling on the energy consumption. Two different sets of production schedules have been evaluated, the first one fulfilling the production requirement in one shift of 10 hours, at high rate, the second one using two 7-hour-long shifts at medium production rate. It was found that the unit cost was minimized in the warmest months of spring and fall, and system shutdown was a crucial factor to reduce energy consumption. A fifth hypothetical scenario was run, with a 4 month continuous production and an 8 month total shutdown, which reduced the energy consumption to a half of the best realistic scenario. When the plant was run in a two-shifts configuration, the cost to coat a vehicle was found to be 29 with weekend shutdown, and 39 without. In the one-shift configuration, the cost was slightly higher, but the difference was less than 5%. While the fifth scenario showed a consistent reduction of the unit cost, inventory and logistic expenses deriving from the

  12. An automatic system using mobile-agent software to model the calculation process of a chemical vapor deposition film deposition simulator.

    Science.gov (United States)

    Takahashi, Takahiro; Fukui, Noriyuki; Arakawa, Masamoto; Funatsu, Kimito; Ema, Yoshinori

    2011-09-01

    We have developed an automatic modeling system for calculation processes of the simulator to reproduce experimental results of chemical vapor deposition (CVD), in order to decrease the calculation cost of the simulator. Replacing the simulator by the mathematical models proposed by the system will contribute towards decreasing the calculation costs for predicting the experimental results. The system consists of a mobile agent and two software resources in computer networks, that is, generalized modeling software and a simulator reproducing cross-sections of the deposited films on the substrates with the micrometer- or nanometer-sized trenches. The mobile agent autonomously creates appropriate models by moving to and then operating the software resources. The models are calculated by partial least squares regression (PLS), quadratic PLS (QPLS) and error back propagation (BP) methods using artificial neural networks (ANN) and expresses by mathematical formulas to reproduce the calculated results of the simulator. The models show good reproducibility and predictability both for uniformity and filling properties of the films calculated by the simulator. The models using the BP method yield the best performance. The filling property data are more suitable to modeling than film uniformity.

  13. Nanostructured TaxC interlayer synthesized via double glow plasma surface alloying process for diamond deposition on cemented carbide

    Science.gov (United States)

    Rong, Wolong; Hei, Hongjun; Zhong, Qiang; Shen, Yanyan; Liu, Xiaoping; Wang, Xin; Zhou, Bing; He, Zhiyong; Yu, Shengwang

    2015-12-01

    The aim in this work was to improve the adhesion of diamond coating with pre-deposition of a TaxC interlayer on cemented carbide (WC-Co) substrate by double glow plasma surface alloying technique. The following deposition of diamond coating on the interlayer was performed in a microwave plasma chemical vapor deposition (MPCVD) reactor. TaxC interlayer with an inner diffusion layer and an outer deposition layer was composed of Ta2C and TaC nanocrystalline, and it exhibited a special compact surface morphology formed of flower-shaped pits. As the gradual element distributions existed in the diffusion layer, the interlayer displayed a superior adherence to the substrate with significantly enhanced surface microhardness to the original substrate. After CVD process, the preferred orientation of TaC changed from (2 2 2) to (2 0 0) plane, and a uniform and tense diamond coating with adhesion referred to class HF 2 at least (Verein Deutscher Ingenieure 3198 norm) was obtained on the interlayered substrate. It indicated that the diffusion of Co was effectively inhibited by the formation of TaxC diffusion-deposition interlayer. The TaxC interlayer is most likely to improve the performance of diamond coatings used in cutting tools.

  14. Radiation processing of liquid with low energy electron accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2003-02-01

    Radiation induced emulsion polymerization, radiation vulcanization of NR latex (RVNRL) and radiation degradation of natural polymers were selected and reviewed as the radiation processing of liquid. The characteristic of high dose rate emulsion polymerization is the occurrence of cationic polymerization. Thus, it can be used for the production of new materials that cannot be obtained by radical polymerization. A potential application will be production of polymer emulsion that can be used as water-borne UV/EB curing resins. The technology of RVNRL by {gamma}-ray has been commercialized. RVNRL with low energy electron accelerator is under development for further vulcanization cost reduction. Vessel type irradiator will be favorable for industrial application. Radiation degradation of polysaccharides is an emerging and promising area of radiation processing. However, strict cost comparison between liquid irradiation with low energy EB and state irradiation with {gamma}-ray should be carried out. (author)

  15. Energy-Driven Image Interpolation Using Gaussian Process Regression

    Directory of Open Access Journals (Sweden)

    Lingling Zi

    2012-01-01

    Full Text Available Image interpolation, as a method of obtaining a high-resolution image from the corresponding low-resolution image, is a classical problem in image processing. In this paper, we propose a novel energy-driven interpolation algorithm employing Gaussian process regression. In our algorithm, each interpolated pixel is predicted by a combination of two information sources: first is a statistical model adopted to mine underlying information, and second is an energy computation technique used to acquire information on pixel properties. We further demonstrate that our algorithm can not only achieve image interpolation, but also reduce noise in the original image. Our experiments show that the proposed algorithm can achieve encouraging performance in terms of image visualization and quantitative measures.

  16. Isotopic evidence for the occurrence of biological nitrification and nitrogen deposition processing in forest canopies.

    Science.gov (United States)

    Guerrieri, Rossella; Vanguelova, Elena I; Michalski, Greg; Heaton, Timothy H E; Mencuccini, Maurizio

    2015-12-01

    This study examines the role of tree canopies in processing atmospheric nitrogen (Ndep ) for four forests in the United Kingdom subjected to different Ndep : Scots pine and beech stands under high Ndep (HN, 13-19 kg N ha(-1)  yr(-1) ), compared to Scots pine and beech stands under low Ndep (LN, 9 kg N ha(-1)  yr(-1) ). Changes of NO3 -N and NH4 -N concentrations in rainfall (RF) and throughfall (TF) together with a quadruple isotope approach, which combines δ(18) O, Δ(17) O and δ(15) N in NO3 (-) and δ(15) N in NH4 (+) , were used to assess N transformations by the canopies. Generally, HN sites showed higher NH4 -N and NO3 -N concentrations in RF compared to the LN sites. Similar values of δ(15) N-NO3 (-) and δ(18) O in RF suggested similar source of atmospheric NO3 (-) (i.e. local traffic), while more positive values for δ(15) N-NH4 (+) at HN compared to LN likely reflected the contribution of dry NHx deposition from intensive local farming. The isotopic signatures of the N-forms changed after interacting with tree canopies. Indeed, (15) N-enriched NH4 (+) in TF compared to RF at all sites suggested that canopies played an important role in buffering dry Ndep also at the low Ndep site. Using two independent methods, based on δ(18) O and Δ(17) O, we quantified for the first time the proportion of NO3 (-) in TF, which derived from nitrification occurring in tree canopies at the HN site. Specifically, for Scots pine, all the considered isotope approaches detected biological nitrification. By contrast for the beech, only using the mixing model with Δ(17) O, we were able to depict the occurrence of nitrification within canopies. Our study suggests that tree canopies play an active role in the N cycling within forest ecosystems. Processing of Ndep within canopies should not be neglected and needs further exploration, with the combination of multiple isotope tracers, with particular reference to Δ(17) O. © 2015 John Wiley & Sons Ltd.

  17. High Energy Description of Processes with Multiple Hard Jets

    CERN Document Server

    Andersen, Jeppe R

    2010-01-01

    High Energy Jets (HEJ) is a new framework for approximating the all-order perturbative corrections to multi-jet processes, with a focus on the hard, wide-angle QCD emissions, which underpins the perturbative description of hard jets. In this contribution we review the basic concepts of HEJ, and present some new predictions for observables in dijet-production, and for W-boson production in association with at least 3 jets.

  18. High Energy Description of Processes with Multiple Hard Jets

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, Jeppe R. [Theory Division, Physics Department, CERN, CH-1211 Geneva 23 (Switzerland); Smillie, Jennifer M. [Department of Physics, UCL, Gower Street, WC1E 6BT (United Kingdom)

    2010-08-15

    High Energy Jets (HEJ) is a new framework for approximating the all-order perturbative corrections to multi-jet processes, with a focus on the hard, wide-angle QCD emissions, which underpins the perturbative description of hard jets. In this contribution we review the basic concepts of HEJ, and present some new predictions for observables in dijet-production, and for W-boson production in association with at least 3 jets.

  19. Energy efficient solvent regeneration process for carbon dioxide capture

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Shaojun; Meyer, Howard S.; Li, Shiguang

    2018-02-27

    A process for removing carbon dioxide from a carbon dioxide-loaded solvent uses two stages of flash apparatus. Carbon dioxide is flashed from the solvent at a higher temperature and pressure in the first stage, and a lower temperature and pressure in the second stage, and is fed to a multi-stage compression train for high pressure liquefaction. Because some of the carbon dioxide fed to the compression train is already under pressure, less energy is required to further compress the carbon dioxide to a liquid state, compared to conventional processes.

  20. Solar energy in food processing-a critical appraisal.

    Science.gov (United States)

    Eswara, Amruta R; Ramakrishnarao, M

    2013-04-01

    Increasing population and high cost of fuels have created opportunities for using alternate energies for post-harvest processing of foods. Solar food processing is an emerging technology that provides good quality foods at low or no additional fuel costs. A number of solar dryers, collectors and concentrators are currently being used for various steps in food processing and value addition. Society for Energy, Environment and Development (SEED) developed Solar Cabinet Dryer with forced circulation which has been used for dehydration and development of value added products from locally grown fruits, vegetables, leafy greens and forest produce. Drying under simulated shade conditions using UV-reducing Blue filter helps retain nutrients better. Its simple design and ease of handling makes SEED Solar Dryer an ideal choice for application of food processing in rural settings, closer to where the harvest is produced, eliminating the need for expensive transportation or storage of fresh produce. It also creates employment opportunities among the rural population, especially women. Other gadgets based on solar collectors and concentrators currently being used at various steps of food processing are reviewed.

  1. Towards energy neutrality of wastewater treatment plants via deammonification process

    Directory of Open Access Journals (Sweden)

    Janiak Kamil

    2017-01-01

    Full Text Available Energy neutrality of wastewater treatment plants is possible with constant and consistent optimization and implementation of new technologies. In recent years new process called deammonification has been discovered and implemented in treatment of side streams rich in nitrogen. With its implementation on wastewater treatment plants it is possible to remove nearly all nitrogen from side stream (even 30% of overall nitrogen load in less energy consuming way. Additionally, thanks to lower nitrogen load to main stream reactors it is possible to optimize them to further lower energy consumption. This article presents simulation studies of deammonification implementation and main stream reactor optimization in case of medium Polish WWTP (115 000 p.e.. With removal of 20% of nitrogen in side stream via deammonification and subsequent main line optimization it is possible to save 5000 euro/year by lowering sludge retention time, oxygen concentration in main stream reactors. When additional COD is precipitated in primary clarifiers with iron coagulants, 55 000 euro/year can be saved in case of energy costs which states for most of the energy costs. However, when coagulant and disposal costs are included savings are on the level of 25 000 euro/year.

  2. Towards energy neutrality of wastewater treatment plants via deammonification process

    Science.gov (United States)

    Janiak, Kamil; Łojek, Andrzej; Muszyński-Huhajło, Mateusz

    2017-11-01

    Energy neutrality of wastewater treatment plants is possible with constant and consistent optimization and implementation of new technologies. In recent years new process called deammonification has been discovered and implemented in treatment of side streams rich in nitrogen. With its implementation on wastewater treatment plants it is possible to remove nearly all nitrogen from side stream (even 30% of overall nitrogen load) in less energy consuming way. Additionally, thanks to lower nitrogen load to main stream reactors it is possible to optimize them to further lower energy consumption. This article presents simulation studies of deammonification implementation and main stream reactor optimization in case of medium Polish WWTP (115 000 p.e.). With removal of 20% of nitrogen in side stream via deammonification and subsequent main line optimization it is possible to save 5000 euro/year by lowering sludge retention time, oxygen concentration in main stream reactors. When additional COD is precipitated in primary clarifiers with iron coagulants, 55 000 euro/year can be saved in case of energy costs which states for most of the energy costs. However, when coagulant and disposal costs are included savings are on the level of 25 000 euro/year.

  3. Development of coatings for ultrasonic additive manufacturing sonotrode using laser direct metal deposition process

    Energy Technology Data Exchange (ETDEWEB)

    Niyanth S, Niyanth [ORNL; Dehoff, Ryan R [ORNL; Jordan, Brian H [ORNL; Babu, Sudarsanam Suresh [ORNL

    2016-10-01

    ORNL partnered with Fabrisonic, LLC to develop galling resistant hard facing coatings on sonotrodes used to fabricate 3D printed materials using ultrasonic additive manufacturing. The development and deployment of a coated sonotrode is expected to push the existing state of the art to facilitate the solidstate additive manufacturing of hard steels and titanium alloys. To this effect a structurally amorphous stainless steel material and cobalt chrome material were deposited on the sonotrode material. Both the deposits showed good adhesion to the substrate. The coatings made using the structurally amorphous steel materials showed cracking during the initial trials and cracking was eliminated by deposition on a preheated substrate. Both the coatings show hardness in excess of 600 HVN. Thus the phase 1 of this project has been used to identify suitable materials to use to coat the sonotrode. Despite the fact that successful deposits were obtained, the coatings need to be evaluated by performing detailed galling tests at various temperatures. In addition field tests are also necessary to test the stability of these coatings in a high cycle ultrasonic vibration mode. If awarded, phase 2 of the project would be used to optimize the composition of the deposit material to maximize galling resistance. The industrial partner would then use the coated sonotrode to fabricate builds made of austenitic stainless steel to test the viability of using a coated sonotrode.

  4. Plasma-enhanced deposition and processing of transition metals and transition metal silicides for VLSI

    Science.gov (United States)

    Hess, D. W.

    1986-05-01

    Radiofrequency (rf) discharges have been used to deposit films of tungsten, molybdenum and titanium silicide. As-deposited tungsten films, from tungsten hexafluoride and hydrogen source gases, were metastable (beta W), with significant (>1 atomic percent) fluorine incorporation. Film resistivities were 40-55 micro ohm - cm due to the beta W, but dropped to about 8 micro ohm cm after a short heat treatment at 700 C which resulted in a phase transition to alpha W (bcc form). The high resistivity (>10,000 micro ohm) associated with molybdenum films deposited from molybdenum hexafluoride and hydrogen appeared to be a result of the formation of molybdenum trifluoride in the deposited material. Titanium silicide films formed from a discharge of titanium tetrachloride, silane, and hydrogen, displayed resistivities of about 150 micro ohm cm, due to small amounts of oxygen and chlorine incorporated during deposition. Plasma etching studies of tungsten films with fluorine containing gases suggest that the etchant species for tungsten in these discharges are fluorine atoms.

  5. Correlation between energy deposition and molecular damage from Auger electrons: A case study of ultra-low energy (5-18 eV) electron interactions with DNA.

    Science.gov (United States)

    Rezaee, Mohammad; Hunting, Darel J; Sanche, Léon

    2014-07-01

    The present study introduces a new method to establish a direct correlation between biologically related physical parameters (i.e., stopping and damaging cross sections, respectively) for an Auger-electron emitting radionuclide decaying within a target molecule (e.g., DNA), so as to evaluate the efficacy of the radionuclide at the molecular level. These parameters can be applied to the dosimetry of Auger electrons and the quantification of their biological effects, which are the main criteria to assess the therapeutic efficacy of Auger-electron emitting radionuclides. Absorbed dose and stopping cross section for the Auger electrons of 5-18 eV emitted by(125)I within DNA were determined by developing a nanodosimetric model. The molecular damages induced by these Auger electrons were investigated by measuring damaging cross section, including that for the formation of DNA single- and double-strand breaks. Nanoscale films of pure plasmid DNA were prepared via the freeze-drying technique and subsequently irradiated with low-energy electrons at various fluences. The damaging cross sections were determined by employing a molecular survival model to the measured exposure-response curves for induction of DNA strand breaks. For a single decay of(125)I within DNA, the Auger electrons of 5-18 eV deposit the energies of 12.1 and 9.1 eV within a 4.2-nm(3) volume of a hydrated or dry DNA, which results in the absorbed doses of 270 and 210 kGy, respectively. DNA bases have a major contribution to the deposited energies. Ten-electronvolt and high linear energy transfer 100-eV electrons have a similar cross section for the formation of DNA double-strand break, while 100-eV electrons are twice as efficient as 10 eV in the induction of single-strand break. Ultra-low-energy electrons (electron emitting radionuclides; hence, they should be considered in the dosimetry calculation of such radionuclides. Moreover, absorbed dose is not an appropriate physical parameter for nanodosimetry

  6. Correlation between energy deposition and molecular damage from Auger electrons: A case study of ultra-low energy (5–18 eV) electron interactions with DNA

    Science.gov (United States)

    Rezaee, Mohammad; Hunting, Darel J.; Sanche, Léon

    2015-01-01

    Purpose The present study introduces a new method to establish a direct correlation between biologically related physical parameters (i.e., stopping and damaging cross sections, respectively) for an Auger-electron emitting radionuclide decaying within a target molecule (e.g., DNA), so as to evaluate the efficacy of the radionuclide at the molecular level. These parameters can be applied to the dosimetry of Auger electrons and the quantification of their biological effects, which are the main criteria to assess the therapeutic efficacy of Auger-electron emitting radionuclides. Methods Absorbed dose and stopping cross section for the Auger electrons of 5–18 eV emitted by 125I within DNA were determined by developing a nanodosimetric model. The molecular damages induced by these Auger electrons were investigated by measuring damaging cross section, including that for the formation of DNA single- and double-strand breaks. Nanoscale films of pure plasmid DNA were prepared via the freeze-drying technique and subsequently irradiated with low-energy electrons at various fluences. The damaging cross sections were determined by employing a molecular survival model to the measured exposure–response curves for induction of DNA strand breaks. Results For a single decay of 125I within DNA, the Auger electrons of 5–18 eV deposit the energies of 12.1 and 9.1 eV within a 4.2-nm3 volume of a hydrated or dry DNA, which results in the absorbed doses of 270 and 210 kGy, respectively. DNA bases have a major contribution to the deposited energies. Ten-electronvolt and high linear energy transfer 100-eV electrons have a similar cross section for the formation of DNA double-strand break, while 100-eV electrons are twice as efficient as 10 eV in the induction of single-strand break. Conclusions Ultra-low-energy electrons (electron emitting radionuclides; hence, they should be considered in the dosimetry calculation of such radionuclides. Moreover, absorbed dose is not an appropriate

  7. Comparison Between Modern and Fossil Examples, a Key to Understand Mass-Transport Deposits and Processes

    Science.gov (United States)

    Pini, G.; Ogata, K.; Camerlenghi, A.; Codegone, G.; Festa, A.; Lucente, C.

    2011-12-01

    investigating methods and the increasing work of comparison between mélanges in the circum-Mediterranean chains, mass-transport is gaining more and more attention as one of the leading mechanism of chaoticization. Several MTCs have been, therefore, recognized as a consistent part of mélanges, even if strongly deformed by post-depositional, tectonic and/or mud-diapiric processes. The presence of these bodies might help in explaining the discrepancies pointed out before. Moreover, the structural-sedimentological study of fossil sedimentary mélanges/MTCs has enabled the distinction of three different kind of bodies/complexes, in which the movements are enabled by 1) shear-dominated viscous flows within a muddy matrix, 2) mud-silt-sandy matrix sustained by fluid overpressure, 3) concentrated shear zones/surfaces with advection of grains and fluid (overpressured basal carpets). These MTC types may represent end-members of a continuum of products and correspond to different kinematics of transport and emplacement and to different relationship with the substratum.

  8. Photocatalytic evaluation of self-assembled porous network structure of ferric oxide film fabricated by dry deposition process

    Energy Technology Data Exchange (ETDEWEB)

    Park, Yunchan; Kim, Hyungsub; Lee, Geon-Yong; Pawar, Rajendra C.; Lee, Jai-Sung; Lee, Caroline Sunyong, E-mail: sunyonglee@hanyang.ac.kr

    2016-09-15

    Ferric oxide powder in the alpha phase (α-Fe{sub 2}O{sub 3}) was deposited on an aluminum oxide (Al{sub 2}O{sub 3}) substrate by a nanoparticle deposition system using the dry deposition method. X-ray diffraction (XRD) images confirmed that the phase of the deposited α-Fe{sub 2}O{sub 3} did not change. The deposited α-Fe{sub 2}O{sub 3} was characterized in terms of its microstructure using scanning electron microscopy (SEM). A porous network microstructure formed when small agglomerates of Fe{sub 2}O{sub 3} (SAF) were deposited. The deposition and formation mechanism of the microstructure were investigated using SEM and three-dimensional (3D) profile analysis. First, a dense coating layer formed when the film was thinner than the particle size. After that, as the film thickness increased to over 5 μm, the porous network structure formed by excavating the surface of the coating layer as it was bombarded by particles. Rhodamine B (RhB) was degraded after 6 h of exposure to the Fe{sub 2}O{sub 3} coating layer with SAF, which has good photocatalytic activity and a high porous network structure. The kinetic rate constants of the SAF and large agglomerates of Fe{sub 2}O{sub 3} (LAF) were calculated to be 0.197(h{sup −1}) and 0.128(h{sup −1}), respectively, based on the absorbance results. Using linear sweep voltammetry, we confirmed that the photoelectric effect occurred in the coating layer by measuring the resulting current under illuminated and dark conditions. - Graphical abstract: Self-assembled porous photocatalytic film fabricated by dry deposition method for water purification. - Highlights: • Different sizes of Fe{sub 2}O{sub 3} agglomerates were used to form porous network structure. • Fe{sub 2}O{sub 3} agglomerate particles were deposited using solvent-free process. • Self-assembled porous network microstructure formed better with small agglomerates of Fe{sub 2}O{sub 3}. • Fabricated porous network structure showed its potential to be used

  9. Thin and flexible Ni-P based current collectors developed by electroless deposition for energy storage devices

    Science.gov (United States)

    Wu, Haoran; Susanto, Amelia; Lian, Keryn

    2017-02-01

    A PET film metalized by electroless nickel deposition was demonstrated as thin and flexible current collector for energy storage devices. The resultant nickel-on-PET film (Ni-PET) can be used both as current collector for electrochemical capacitors and as electrode for thin film batteries. The composition of Ni-PET was characterized by EDX and XPS. The electrochemical performance of the Ni-PET current collector was similar to Ni foil but with less hydrogen evolution at low potential. The Ni-PET film exhibited better flexibility than a metallic Ni foil. Carbon nanotubes were coated on a Ni-PET substrate to form an electrochemical capacitor electrode which exhibited high chemical stability in both liquid and solid electrolytes, showing strong promise for solid energy storage devices.

  10. A Humidity Sensor Based on Silver Nanoparticles Thin Film Prepared by Electrostatic Spray Deposition Process

    Directory of Open Access Journals (Sweden)

    Thutiyaporn Thiwawong

    2013-01-01

    Full Text Available In this work, thin film of silver nanoparticles for humidity sensor application was deposited by electrostatic spray deposition technique. The influence of the deposition times on properties of films was studied. The crystal structures of sample films, their surface morphology, and optical properties have been investigated by X-ray diffraction (XRD, field emission scanning electron microscopy (FE-SEM, and UV-VIS spectrophotometer, respectively. The crystalline structure of silver nanoparticles thin film was found in the orientation of (100 and (200 planes of cubic structure at diffraction angles 2θ  =  38.2° and 44.3°, respectively. Moreover, the silver nanoparticles thin films humidity sensor was fabricated onto the interdigitated electrodes. The sensor exhibited the humidity adsorption and desorption properties. The sensing mechanisms of the device were also elucidated by complex impedance analysis.

  11. Process and Economic Optimisation of a Milk Processing Plant with Solar Thermal Energy

    DEFF Research Database (Denmark)

    Bühler, Fabian; Nguyen, Tuong-Van; Elmegaard, Brian

    2016-01-01

    . Based on the case study of a dairy factory, where first a heat integration is performed to optimise the system, a model for solar thermal process integration is developed. The detailed model is based on annual hourly global direct and diffuse solar radiation, from which the radiation on a defined...... surface is calculated. Based on hourly process stream data from the dairy factory, the optimal streams for solar thermal process integration are found, with an optimal thermal storagetank volume. The last step consists of an economic optimisation of the problem to determine the optimal size......This work investigates the integration of solar thermal systems for process energy use. A shift from fossil fuels to renewable energy could be beneficial both from environmental and economic perspectives, after the process itself has been optimised and efficiency measures have been implemented...

  12. Process Parameters for Successful Synthesis of Carbon Nanotubes by Chemical Vapor Deposition: Implications for Chemical Mechanisms and Life-cycle Assessment

    Science.gov (United States)

    Xue, Ke

    Manufacturing of carbon nanotubes (CNTs) via chemical vapor deposition (CVD) calls for thermal treatment associated with gas-phase rearrangement and catalyst deposition to achieve high cost efficiency and limited influence on environmental impact. Taking advantage of higher degree of structure control and economical efficiency, catalytic chemical vapor deposition (CCVD) has currently become the most prevailing synthesis approach for the synthesis of large-scale pure CNTs in past years. Because the synthesis process of CNTs dominates the potential ecotoxic impacts, materials consumption, energy consumption and greenhouse gas emissions should be further limited to efficiently reduce life cycle ecotoxicity of carbon naotubes. However, efforts to reduce energy and material requirements in synthesis of CNTs by CCVD are hindered by a lack of mechanistic understanding. In this thesis, the effect of operating parameters, especially the temperature, carbon source concentration, and residence time on the synthesis were studied to improve the production efficiency in a different angle. Thus, implications on the choice of operating parameters could be provided to help the synthesis of carbon nanotubes. Here, we investigated the typical operating parameters in conditions that have yielded successful CNT production in the published academic literature of over seventy articles. The data were filtered by quality of the resultant product and deemed either "successful" or "unsuccessful" according to the authors. Furthermore, growth rate data were tabulated and used as performance metric for the process whenever possible. The data provided us an opportunity to prompt possible and common methods for practioners in the synthesis of CNTs and motivate routes to achieve energy and material minimization. The statistical analysis revealed that methane and ethylene often rely on thermal conversion process to form direct carbon precursor; further, methane and ethylene could not be the direct

  13. Developement and characterization of environmentally friendly gold and nickel electrolytes based on ionic liquids for the electroless metal deposition in the ENIG process

    OpenAIRE

    Krüger, Frank-Marc

    2014-01-01

    In the present work two different metal deposition processes for the electroless nickel immersion gold (ENIG) surface plating are characterized in “Deep Eutectic Solvents” (DES). It is shown for the first time that the immersion nickel deposition on copper substrates in a DES based electrolyte can be realized despite the fact that in aqueous solutions the redox potentials would not allow the displacement deposition. For the immersion gold process an electrolyte is developed whi...

  14. Formation of Cusub(x)S thin films through a chemical bath deposition process

    Energy Technology Data Exchange (ETDEWEB)

    Fatas, E.; Garcia, T.; Montemayor, C.; Medina, A.; Garcia Camarero, E.; Arjona, F.

    1985-02-01

    A method for the preparation of Cusub(x)S thin films through chemical bath deposition is described. The films have been formed on a glass substrate from a bath containing a triethanolamine complex of copper ions, ammonia and thiourea. The stoichiometry and optical characteristics of the films have been determined. This method has been used to form a solar cell through deposition of Cusub(x)S on a CdS substrate. The I-V characteristics of the cell are reported.

  15. Experimental investigation on the energy deposition and morphology of the electrical explosion of copper wire in vacuum

    Science.gov (United States)

    Shi, Zongqian; Shi, Yuanjie; Wang, Kun; Jia, Shenli

    2016-03-01

    This paper presents the experimental results of the electrical explosion of copper wires in vacuum using negative nanosecond-pulsed current with magnitude of 1-2 kA. The 20 μm-diameter copper wires with different lengths are exploded with three different current rates. A laser probe is applied to construct the shadowgraphy and interferometry diagnostics to investigate the distribution and morphology of the exploding product. The interference phase shift is reconstructed from the interferogram, by which the atomic density distribution is calculated. Experimental results show that there exist two voltage breakdown modes depending on the amount of the specific energy deposition. For the strong-shunting mode, shunting breakdown occurs, leading to the short-circuit-like current waveform. For the weak-shunting mode with less specific energy deposition, the plasma generated during the voltage breakdown is not enough to form a conductive plasma channel, resulting in overdamped declining current waveform. The influence of the wire length and current rate on the characteristics of the exploding wires is also analyzed.

  16. City and Energy Infrastructures between Economic Processes and Urban Planning

    Directory of Open Access Journals (Sweden)

    Giuseppe Mazzeo

    2013-11-01

    Full Text Available The paper deals with the issues related to the relationship between city, energy, economic factors and city planning. These issues are analyzed from a theoretical point of view and are placed in a logical path based on three assumptions. The first considers the city as an intelligent system constantly evolving. The second considers the city as a system where economic processes come out at their highest level affecting other aspects of social and urban structure. The third considers the planning as the weak link in the process of urban development, one of the most exposed to economic and social pressures.Energy production has experienced a great progress since steam and electricity were discovered. Each stage of this evolution has affected city and territory introducing significant physical signs, changing the ways of carrying out functions and creating new needs and new activities. The energy revolution, based on sustainable sources and on skillful management of the networks, will strongly affect the city and the way of organizing the activities, their location, dimension, and the shape of the spaces.The paper explores some of the issues related to the relationship between urban system and energy.The first section analyzes the meaning of the intelligent city as an entity that is constantly changing and constantly adapting. The second section analyzes the role of the energy systems in the evolution of the activities and of the city’s image. The last section investigates the role of the economic factors in the evolution of the shape and meaning of city, pointing out that the way towards smart and green urban systems will largely depend on their economic advantage. 

  17. Energy-efficient Spin-polarized Multilevel Information Processing

    Science.gov (United States)

    Hong, Jeong; Berkeley Team

    Magnetic memory and logic devices have advantages of non-volatility, radiation hardness, scalability down to the sub-5-nm range, straightforward three-dimensional (3D) integration and data-intensive multi-level capability. Despite these unique advantages, development of practical nonmagnetic 3D devices for new information processing applications faces many challenges. A major stumbling block is the relatively high energy required to switch information states in the new nano devices. Specifically, using a separate recording transducer to directly apply an external magnetic field to switch magnetic states in a nanomagnetic information bit is extremely energy inefficient. The spin =transfer torque (STT) method has been introduced to overcome this issue by using a spin-polarized electric current instead of an external field. However, the switching current density on the order of 1 MA/cm^2 in state-of-the-art STT magnetic tunneling junctions under exploration still remains high for many information processing applications. In this talk, we present a case study in which two junctions are placed in series to enable ternary and higher multilevel information processing in a very small nonmagnetic structure. The system can be transitioned between three states through application of certain voltage values. Other cases will be discussed in the presentation. This type of nonmagnetic junction with multilevel signal processing could be used for a building block for future 3D electronics.

  18. Energy-Deposition to Reduce Skin Friction in Supersonic Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA has drawn attention to an impending need to improve energy-efficiency in low supersonic (M<~3) platforms. Aerodynamic efficiency is the foundation of...

  19. Investigation of the surface free energy of the ITO thin films deposited under different working pressure

    Energy Technology Data Exchange (ETDEWEB)

    Özen, Soner, E-mail: osoner@ogu.edu.tr; Pat, Suat; Korkmaz, Şadan [Eskişehir Osmangazi University, Physics Department, 26480 (Turkey); Şenay, Volkan [Eskişehir Osmangazi University, Physics Department, 26480 (Turkey); Bayburt University, Primary Science Education Department, 69000 (Turkey)

    2016-03-25

    This study discusses the influence of working pressure on the surface energy of the ITO thin films produced by radio frequency magnetron sputtering method. Optical tensiometer (Attension Theta Lite) is used for evaluating wetting behavior of the water droplet on the film surface and Equation of State method was selected to determine surface free energy for this study. Equation of state method does not divide the surface tension into different components such as polar, dispersive, acid-base. It is calculated the surfaces’ free energy measuring the contact angle with a single liquid. The surface free energy value was in the range of 15-31 mN/m. Also, the transmittances were determined in the wavelength range between 200 and 1000 nm using the UNICO 4802 UV-Vis double beam spectrophotometer. Transmittances of the produced ITO thin films are greater than %70 in the visible range.

  20. Detectors and signal processing for high-energy physics

    Energy Technology Data Exchange (ETDEWEB)

    Rehak, P.

    1981-01-01

    Basic principles of the particle detection and signal processing for high-energy physics experiments are presented. It is shown that the optimum performance of a properly designed detector system is not limited by incidental imperfections, but solely by more fundamental limitations imposed by the quantum nature and statistical behavior of matter. The noise sources connected with the detection and signal processing are studied. The concepts of optimal filtering and optimal detector/amplifying device matching are introduced. Signal processing for a liquid argon calorimeter is analyzed in some detail. The position detection in gas counters is studied. Resolution in drift chambers for the drift coordinate measurement as well as the second coordinate measurement is discussed.

  1. Impact of acid atmospheric deposition on soils : quantification of chemical and hydrologic processes

    NARCIS (Netherlands)

    Grinsven, van J.J.M.

    1988-01-01

    Atmospheric deposition of SO x , NOx and NHx will cause major changes in the chemical composition of solutions in acid soils, which may affect the biological functions of the soil. This thesis deals with quantification of soil acidification by means of chemical

  2. Growth Process Conditions of Tungsten Oxide Thin Films Using Hot-Wire Chemical Vapor Deposition

    NARCIS (Netherlands)

    Houweling, Z.S.|info:eu-repo/dai/nl/251874486; Geus, J.W.; de Jong, M.; Harks, P.P.R.M.L.; van der Werf, C.H.M.; Schropp, R.E.I.|info:eu-repo/dai/nl/072502584

    2011-01-01

    We report the growth conditions of nanostructured tungsten oxide (WO3−x) thin films using hot-wire chemical vapor deposition (HWCVD). Two tungsten filaments were resistively heated to various temperatures and exposed to an air flow at various subatmospheric pressures. The oxygen partial pressure was

  3. One-step electrodeposition process of CuInSe2: Deposition time effect

    Indian Academy of Sciences (India)

    Administrator

    Electrodeposition; CuInSe2; deposition time; thin films. 1. Introduction. Chalcopyrite, CuInSe2, is considered one of the most im- portant semiconductors that can be used to make low-cost photovoltaic devices. It has high absorption coefficient. (> 105 cm–1) (Kavcar et al 1992; Huang et al 2004), rea- sonable work function ...

  4. Modeling of thermal processes during vapor deposition of material on curvilinear surface

    Science.gov (United States)

    Savel’eva, I. Yu; Zhuravskii, A. V.

    2017-11-01

    A mathematical model has been constructed that describes the deposition of material on a curvilinear surface. This model considers convective heat transfer, heat transfer by radiation, and heat and mass transfer during the attachment of the substance to the surface. For the model numerical algorithm is constructed to find the temperature profile in a curvilinear plate; results of calculations for different materials are given.

  5. Energy conversion processes for the use of geothermal heat

    Energy Technology Data Exchange (ETDEWEB)

    Minder, R. [Minder Energy Consulting, Oberlunkhofen (Switzerland); Koedel, J.; Schaedle, K.-H.; Ramsel, K. [Gruneko AG, Basel (Switzerland); Girardin, L.; Marechal, F. [Swiss Federal Institute of Technology (EPFL), Laboratory for industrial energy systems (LENI), Lausanne (Switzerland)

    2007-03-15

    This comprehensive final report for the Swiss Federal Office of Energy (SFOE) presents the results of a study made on energy conversion processes that can be used when geothermal heat is to be used. The study deals with both theoretical and practical aspects of the conversion of geothermal heat to electricity. The report is divided into several parts and covers general study, practical experience, planning and operation of geothermal power plants as well as methodology for the optimal integration of energy conversion systems in geothermal power plants. In the first part, the specific properties and characteristics of geothermal resources are discussed. Also, a general survey of conversion processes is presented with special emphasis on thermo-electric conversion. The second part deals with practical aspects related to planning, construction and operation of geothermal power plant. Technical basics, such as relevant site-specific conditions, drilling techniques, thermal water or brine quality and materials requirements. Further, planning procedures are discussed. Also, operation and maintenance aspects are examined and some basic information on costs is presented. The third part of the report presents the methodology and results for the optimal valorisation of the thermodynamic potential of deep geothermal systems.

  6. A less energy intensive process for dehydrating onion.

    Science.gov (United States)

    Grewal, Manpreet Kaur; Jha, S N; Patil, R T; Dhatt, A S; Kaur, Amandeep; Jaiswal, P

    2015-02-01

    Onion powder has an extensive demand and wide application worldwide as flavour additive in convenience foods and medicinal products. Conventionally onion powder is prepared by hot air drying of onion slices followed by grinding. Convective air drying when used alone demands longer drying time and thus has a high expense of energy. As bulk of onion is water (82-87 %), removal of moisture prior to drying can reduce moisture loading on dryer and hence the energy consumption. Keeping this in view, onions were partially dewatered using centrifugal force before convective drying. The effect of partial mechanical dewatering and drying air temperature was studied on drying time, specific energy consumption and onion powder quality (colour and flavour). The combination process was also optimized to achieve increased drying rate and product quality comparable to products obtained using convective drying alone. Onions subjected to 60 % partial mechanical dewatering and hot air drying at 70 °C exhibited significantly (p ≤ 0.5) shortened drying time, decreased energy consumption and maintained colour and flavour of the dried product.

  7. Trimethyl(phenylsilane — a precursor for gas phase processes of SiCx:H film deposition: Synthesis and characterization

    Directory of Open Access Journals (Sweden)

    Evgeniya N. Ermakova

    2015-12-01

    Full Text Available The technique of synthesis and purification of trimethyl(phenylsilane PhSiMe3, allowing to obtain the product with high yield. Individuality of the product was confirmed by elemental analysis for C, H, Si was developed. IR, UV and 1H NMR-spectroscopic studies were used to define its spectral characteristics. Complex thermal analysis and thermogravimetry defined thermoanalytical behavior of PhSiMe3 in an inert atmosphere. Tensimetric studies have shown that the compound has sufficient volatility and thermal stability for use as a precursor in the process of chemical vapor deposition (CVD. The composition and temperature limits of the possible crystalline phase complexes in equilibrium with the gas phase of different composition has been determined by method of thermodynamic modeling. Calculated CVD diagrams allow us to select the optimal conditions of film deposition. The possibility of using trimethyl(phenylsilane in CVD processes for producing dielectric films of hydrogenated silicon carbide has been demonstrated.

  8. Microwaves energy in curing process of water glass molding sands

    Directory of Open Access Journals (Sweden)

    Granat K.

    2007-01-01

    Full Text Available This work presents the results of investigation of microwave heating on hardening process of water glass molding sands. Essential influence of this heating process on basic properties such as: compression, bending and tensile strength as well as permeability and abrasion resistance has been found. It has been proved, that all investigated sorts of sodium water glass with a module between 2.0 and 3.3 can be used as a binder of molding sands in microwave curing process. It has been found during analysis of research results of sands with 2.5 % water glass addition that they are practically the same as in case of identical molding sands dried for 120 minutes at the temperature of 110°C, used for comparative purposes. Application of microwave curing of molding sands with water glass, however, guarantees reduction of hardening time (from 120 to 4 minutes as well as significant reduction of energy consumption. Attempts of two stage hardening of the investigated water glass molding sands have also been carried out, that is after an initial hardening during a classical CO2 process (identical sands have also been tested for comparison after CO2 blowing process and additional microwave heating. It has been found that application of this kind of treatment for curing sands with 2.5 % sodium water glass content and module from 2.0 up to 3.3 results in the improvement of properties in comparison to classical CO2 process.

  9. Aerosol deposition process for synthesizing optically active nano-scale materials

    Science.gov (United States)

    Chivas, Robert Douglas

    2007-12-01

    The field of optically active polycrystalline materials has two major thrusts: high-power solid-state laser hosts and scintillators. Until recently, the primary focus has been on creating high-power solid-state laser hosts for active ions. An example is Nd:Y2O3, which has the potential to outperform the Nd:YAG solid state laser. More recently, efforts have been directed to scintillating materials. Scintillators emit a visible light photon when excited by x-ray radiation. Applications of this technology range from medical imaging to bomb detection in port security. Lu2O3, YAP, and YAG are oxide scintillators. Criteria for synthesizing optimized particles for use as polycrystalline precursors exist from previous work in the field. These particles should be whole, spherical, solid, unagglomerated and sub-micrometer in size. Prior investigation into transparent oxides has established that such particles must possess cubic crystallinity, or other isometric rotational symmetry (i.e. garnet). In this work we produce particles ideal for use as precursors in polycrystalline transparent oxides. We have synthesized nano-particles for both laser hosts and scintillators, and demonstrate photoluminescence of Nd:Y 2O3. Scintillation of Eu:Lu2O 3 and Ce:YAP has been demonstrated. The primary focus of our work has been to establish and optimize an aerosol synthesis process capable of synthesizing such particles. We believe the process is transferable to any oxide material where liquid precursors exist. Extensions of this method to other materials have also been demonstrated. As an example, we have synthesized nano-scale pure germanium that possesses interesting and possibly unique optical properties. We have demonstrated photoluminescence in two energy bands with distinct lifetimes, indicating they are a result of two separate processes. Investigation of this material is in progress. Over the course of this work, we realized one of our methods preferentially created shell

  10. Mangrove forests submitted to depositional processes and salinity variation investigated using satellite images and vegetation structure surveys

    OpenAIRE

    Cunha-Lignon, M.; Kampel, M.; Menghini, R.P.; Schaeffer-Novelli, Y.; Cintrón, G.; Dahdouh-Guebas, F

    2011-01-01

    The current paper examines the growth and spatio-temporal variation of mangrove forests in response to depositional processes and different salinity conditions. Data from mangrove vegetation structure collected at permanent plots and satellite images were used. In the northern sector important environmental changes occurred due to an artificial channel producing modifications in salinity. The southern sector is considered the best conserved mangrove area along the coast of São Paulo State, Br...

  11. 75 FR 70224 - New York Tidal Energy Company; Notice Concluding Pre-Filing Process and Approving Process Plan...

    Science.gov (United States)

    2010-11-17

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission New York Tidal Energy Company; Notice Concluding Pre-Filing Process and..., 2009. ] d. Submitted By: New York Tidal Energy Company. e. Name of Project: East River Tidal Energy...

  12. Advanced Reactors Thermal Energy Transport for Process Industries

    Energy Technology Data Exchange (ETDEWEB)

    P. Sabharwall; S.J. Yoon; M.G. McKellar; C. Stoots; George Griffith

    2014-07-01

    The operation temperature of advanced nuclear reactors is generally higher than commercial light water reactors and thermal energy from advanced nuclear reactor can be used for various purposes such as liquid fuel production, district heating, desalination, hydrogen production, and other process heat applications, etc. Some of the major technology challenges that must be overcome before the advanced reactors could be licensed on the reactor side are qualification of next generation of nuclear fuel, materials that can withstand higher temperature, improvement in power cycle thermal efficiency by going to combined cycles, SCO2 cycles, successful demonstration of advanced compact heat exchangers in the prototypical conditions, and from the process side application the challenge is to transport the thermal energy from the reactor to the process plant with maximum efficiency (i.e., with minimum temperature drop). The main focus of this study is on doing a parametric study of efficient heat transport system, with different coolants (mainly, water, He, and molten salts) to determine maximum possible distance that can be achieved.

  13. Relationship between the Ca/P ratio of hydroxyapatite thin films and the spatial energy distribution of the ablation laser in pulsed laser deposition

    NARCIS (Netherlands)

    Nishikawa, H.; Hasegawa, T; Miyake, A.; Tashiro, Y.; Hashimoto, Y.; Blank, David H.A.; Rijnders, Augustinus J.H.M.

    2016-01-01

    Variation of the Ca/P ratio in hydroxyapatite (Ca10(PO4)6(OH)2) thin films was studied in relation to the spot size of the ablation laser for two different spatial energy distributions in pulsed laser deposition. One energy distribution is the defocus method with a raw distribution and the other is

  14. Mass and energy deposition effects of implanted ions on solid sodium formate

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xiangqin E-mail: clshao@mail.ipp.ac.cn; Shao Chunlin; Yao Jianming; Yu Zengliang

    2000-07-01

    Solid sodium formate was implanted by low energy N{sup +}, H{sup +}, and Ar{sup +} ions. Measured with electron paramagnetic resonance (EPR) and Fourier-transform infrared (FT-IR), it was observed that new -CH{sub 2}-, -CH{sub 3}- groups and COO{sup -} radical ion were produced in the implanted sodium formate. Analyzing with the highly sensitive ninhydrin reaction, it was found that a new -NH{sub 2} functional group was formed upon N{sup +} ion implantation, and its yield increased along with implantation dose but decreased with the ion's energy.

  15. A study of the energy deposition profile of proton beams in materials of hadron therapeutic interest.

    Science.gov (United States)

    Garcia-Molina, Rafael; Abril, Isabel; de Vera, Pablo; Kyriakou, Ioanna; Emfietzoglou, Dimitris

    2014-01-01

    The energy delivered by a swift proton beam in materials of interest to hadron therapy (liquid water, polymethylmethacrylate or polystyrene) is investigated. An explicit condensed-state description of the target excitation spectrum based on the dielectric formalism is used to calculate the energy-loss rate of the beam in the irradiated materials. This magnitude is the main input in the simulation code SEICS (Simulation of Energetic Ions and Clusters through Solids) used to evaluate the dose as a function of the penetration depth and radial distance from the beam axis. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Film Growth Rates and Activation Energies for Core-Shell Nanoparticles Derived from a CVD Based Aerosol Process.

    Science.gov (United States)

    Weis, Frederik; Seipenbusch, Martin; Kasper, Gerhard

    2015-03-06

    Silica core-shell nanoparticles of about 60-120 nm with a closed outer layer of bismuth or molybdenum oxide of 1-10 nm were synthesized by an integrated chemical vapor synthesis/chemical vapor deposition process at atmospheric pressure. Film growth rates and activation energies were derived from transmission electron microscopy (TEM) images for a deposition process based on molybdenum hexacarbonyl and triphenyl bismuth as respective coating precursors. Respective activation energies of 123 ± 10 and 155 ± 10 kJ/mol are in good agreement with the literature and support a deposition mechanism based on surface-induced removal of the precursor ligands. Clean substrate surfaces are thus prerequisite for conformal coatings. Integrated aerosol processes are solvent-free and intrinsically clean. In contrast, commercial silica substrate particles were found to suffer from organic residues which hinder shell formation, and require an additional calcination step to clean the surface prior to coating. Dual layer core-shell structures with molybdenum oxide on bismuth oxide were synthesized with two coating reactors in series and showed similar film growth rates.

  17. Film Growth Rates and Activation Energies for Core-Shell Nanoparticles Derived from a CVD Based Aerosol Process

    Directory of Open Access Journals (Sweden)

    Frederik Weis

    2015-03-01

    Full Text Available Silica core-shell nanoparticles of about 60–120 nm with a closed outer layer of bismuth or molybdenum oxide of 1–10 nm were synthesized by an integrated chemical vapor synthesis/chemical vapor deposition process at atmospheric pressure. Film growth rates and activation energies were derived from transmission electron microscopy (TEM images for a deposition process based on molybdenum hexacarbonyl and triphenyl bismuth as respective coating precursors. Respective activation energies of 123 ± 10 and 155 ± 10 kJ/mol are in good agreement with the literature and support a deposition mechanism based on surface-induced removal of the precursor ligands. Clean substrate surfaces are thus prerequisite for conformal coatings. Integrated aerosol processes are solvent-free and intrinsically clean. In contrast, commercial silica substrate particles were found to suffer from organic residues which hinder shell formation, and require an additional calcination step to clean the surface prior to coating. Dual layer core-shell structures with molybdenum oxide on bismuth oxide were synthesized with two coating reactors in series and showed similar film growth rates.

  18. Bayesian networks applied to process diagnostics. Applications in energy industry

    Energy Technology Data Exchange (ETDEWEB)

    Widarsson, Bjoern (ed.); Karlsson, Christer; Dahlquist, Erik [Maelardalen Univ., Vaesteraas (Sweden); Nielsen, Thomas D.; Jensen, Finn V. [Aalborg Univ. (Denmark)

    2004-10-01

    Uncertainty in process operation occurs frequently in heat and power industry. This makes it hard to find the occurrence of an abnormal process state from a number of process signals (measurements) or find the correct cause to an abnormality. Among several other methods, Bayesian Networks (BN) is a method to build a model which can handle uncertainty in both process signals and the process itself. The purpose of this project is to investigate the possibilities to use BN for fault detection and diagnostics in combined heat and power industries through execution of two different applications. Participants from Aalborg University represent the knowledge of BN and participants from Maelardalen University have the experience from modelling heat and power applications. The co-operation also includes two energy companies; Elsam A/S (Nordjyllandsverket) and Maelarenergi AB (Vaesteraas CHP-plant), where the two applications are made with support from the plant personnel. The project ended out in two quite different applications. At Nordjyllandsverket, an application based (due to the lack of process knowledge) on pure operation data is build with capability to detect an abnormal process state in a coal mill. Detection is made through a conflict analysis when entering process signals into a model built by analysing the operation database. The application at Maelarenergi is built with a combination of process knowledge and operation data and can detect various faults caused by the fuel. The process knowledge is used to build a causal network structure and the structure is then trained by data from the operation database. Both applications are made as off-online applications, but they are ready for being run on-line. The performance of fault detection and diagnostics are good, but a lack of abnormal process states with known cause reduces the evaluation possibilities. Advantages with combining expert knowledge of the process with operation data are the possibility to represent

  19. Leaching of polycyclic aromatic hydrocarbons from oil shale processing waste deposit: a long-term field study.

    Science.gov (United States)

    Jefimova, Jekaterina; Irha, Natalya; Reinik, Janek; Kirso, Uuve; Steinnes, Eiliv

    2014-05-15

    The leaching behavior of selected polycyclic aromatic hydrocarbons (PAHs) from an oil shale processing waste deposit was monitored during 2005-2009. Samples were collected from the deposit using a special device for leachate sampling at field conditions without disturbance of the upper layers. Contents of 16 priority PAHs in leachate samples collected from aged and fresh parts of the deposit were determined by GC-MS. The sum of the detected PAHs in leachates varied significantly throughout the study period: 19-315 μg/l from aged spent shale, and 36-151 μg/l from fresh spent shale. Among the studied PAHs the low-molecular weight compounds phenanthrene, naphthalene, acenaphthylene, and anthracene predominated. Among the high-molecular weight PAHs benzo[a]anthracene and pyrene leached in the highest concentrations. A spent shale deposit is a source of PAHs that could infiltrate into the surrounding environment for a long period of time. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Fluorine and boron co-doped diamond-like carbon films deposited by pulsed glow discharge plasma immersion ion processing

    CERN Document Server

    He, X M; Peters, A M; Taylor, B; Nastasi, M

    2002-01-01

    Fluorine (F) and boron (B) co-doped diamond-like carbon (FB-DLC) films were prepared on different substrates by the plasma immersion ion processing (PIIP) technique. A pulse glow discharge plasma was used for the PIIP deposition and was produced at a pressure of 1.33 Pa from acetylene (C sub 2 H sub 2), diborane (B sub 2 H sub 6), and hexafluoroethane (C sub 2 F sub 6) gas. Films of FB-DLC were deposited with different chemical compositions by varying the flow ratios of the C sub 2 H sub 2 , B sub 2 H sub 6 , and C sub 2 F sub 6 source gases. The incorporation of B sub 2 H sub 6 and C sub 2 F sub 6 into PIIP deposited DLC resulted in the formation of F-C and B-C hybridized bonding structures. The levels of the F and B concentrations effected the chemical bonding and the physical properties as was evident from the changes observed in density, hardness, stress, friction coefficient, and contact angle of water on films. Compared to B-doped or F-doped DLC films, the F and B co-doping of DLC during PIIP deposition...

  1. A Monte Carlo study of energy deposition at the sub-cellular level for application to targeted radionuclide therapy with low-energy electron emitters

    Science.gov (United States)

    Emfietzoglou, D.; Bousis, C.; Hindorf, C.; Fotopoulos, A.; Pathak, A.; Kostarelos, K.

    2007-03-01

    Optimizing targeted radionuclide therapy for patients with circulating malignant cells (e.g. blood-related cancers) or a micrometastatic spread requires quantification of various dosimetric parameters at the single-cell level. We present results on the energy deposition of monoenergetic electrons of initial energy from 100 eV to 20 keV - relevant to Auger emitting radionuclides - distributed either uniformly or at the surface of spherical volumes of radii from 10 nm to 1 μm which correspond to critical sub-cellular targets. Calculations have been carried out by our detailed-history Monte Carlo (MC) code which simulates event-by-event the complete slowing down (to 1 Ry) of both the primary and all subsequent generations of electrons, as well as, by the continuous-slowing-down-approximation (CSDA) using analytic range-energy relationships. The latter method has been adopted by the MIRD committee of the Society of Nuclear Medicine for dosimetry at the cellular level (>1 μm). Differences between the MC and CSDA results are up to ∼50% and are expected to be even larger at higher energies and/or smaller volumes. They are attributed to the deficiencies of the CSDA method associated with the neglect of straggling and δ-ray transport. The results are particularly relevant to targeted radiotherapy at the genome level by Auger emitters.

  2. Energy and Process Assessment Protocol for Industrial Buildings

    Science.gov (United States)

    2007-05-01

    operation and maintenance procedures pertaining to building energy efficiency . _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _______________________________________________________ ERDC

  3. Urate crystal deposition and bone erosion in gout: 'inside-out' or 'outside-in'? A dual-energy computed tomography study.

    Science.gov (United States)

    Towiwat, Patapong; Doyle, Anthony J; Gamble, Gregory D; Tan, Paul; Aati, Opetaia; Horne, Anne; Stamp, Lisa K; Dalbeth, Nicola

    2016-09-15

    It is currently unknown whether bone erosion in gout occurs through an 'inside-out' mechanism due to direct intra-osseous crystal deposition or through an 'outside-in' mechanism from the surface of bone. The aim of this study was to examine the mechanism ('outside-in' vs. 'inside-out') of monosodium urate (MSU) crystal deposition in bone erosion in gout. Specifically, we used three-dimensional dual-energy computed tomography (DECT) to analyse the positional relationship between bone and MSU crystal deposition in tophaceous gout, and to determine whether intra-osseous crystal deposition occurs in the absence of erosion. One hundred forty-four participants with gout and at least one palpable tophus had a DECT scan of both feet. Two readers independently scored all metatarsal heads (1433 bones available for scoring). For bones in contact with urate, the bone was scored for whether urate was present within an erosion, on the surface of bone or within bone only (true intra-osseous deposit). Data were analysed using generalised estimating equations. Urate in contact with bone was present in 370 (54.3 %) of 681 joints with urate deposition. For those bones in contact with urate, deposition was present on the surface of bone in 143 (38.6 %) of 370 joints and within erosion in 227 (61.4 %) of 370. True intra-osseous urate deposition was not observed at any site (p < 0.0001). For all bones with apparent intra-osseous deposition in one plane, examination in other planes revealed urate deposition within an en face erosion. In tophaceous gout, MSU crystal deposition is present within the joint, on the bone surface and within bone erosion, but it is not observed within bone in the absence of a cortical break. These data support the concept that MSU crystals deposit outside bone and contribute to bone erosion through an 'outside-in' mechanism.

  4. Material deposition and migration processes with resonant magnetic perturbation fields at TEXTOR

    Science.gov (United States)

    Laengner, Ruth; Schmitz, O.; Brezinsek, S.; Coenen, J. W.; Eich, T.; Freisinger, M.; Kirschner, A.; Kreter, A.; Möller, S.; Laengner, M.; Philipps, V.; Pospieszczyk, A.; Reimer, H.; Samm, U.; Wienhold, P.; Textor Team

    2013-07-01

    Resonant Magnetic Perturbations (RMPs) are applied with the Dynamic Ergodic Divertor (DED) at TEXTOR to control the plasma edge transport and the plasma surface interaction. This leads to the formation of a three-dimensional (3D) topology of the scrape-off layer (SOL). To quantify the erosion/deposition balance and the material migration in this 3D boundary, spherical test limiters were exposed to plasmas with and without RMP fields applied. Methane doped with 13C as tracer element was injected through a gas inlet in the test limiter. The local gas source was monitored by spatially resolving spectroscopy and the resulting deposition patterns on the limiters were analysed with colourimetry and nuclear reaction analysis. These measurements were compared to simulations of the magnetic field topology simulations. The data provide evidence of a particle migration dominated by an ExB drift within stochastic zones of the 3D plasma boundary.

  5. Cadmium cathodic deposition on polycrystalline p-selenium: Dark and photoelectrochemical processes

    Energy Technology Data Exchange (ETDEWEB)

    Ragoisha, G.A., E-mail: ragoishag@bsu.b [Research Institute for Physical Chemical Problems, Belarusian State University, Leningradskaya 14, Minsk 220030 (Belarus); Streltsov, E.A.; Rabchynski, S.M.; Ivanou, D.K. [Chemistry Department, Belarusian State University, Minsk 220030 (Belarus)

    2011-04-01

    Cathodic reduction of Cd{sup 2+} on p-Se proceeds at low overpotential in the dark and results in bulk Cd, while the underpotential deposition is kinetically inhibited. Cadmium adlayer is photoelectrochemically deposited on illuminated electrode 0.7 V above E(Cd{sup 2+}/Cd). The adlayer cathodic deposition under illumination proceeds with simultaneous formation of CdSe nanoparticles. Potentiodynamic electrochemical impedance spectroscopy has discriminated the two products of the photoelectrochemical reaction both by their potentials of anodic oxidation and by characteristic dependences of impedance on potential. Anodic oxidation of CdSe nanoparticles gives a sharp peak of real impedance in low frequencies close to the corresponding anodic current peak in cyclic voltammogram. The impedance peak appears below a threshold frequency f{sub t}. The latter separates two modes of diffusion in anodic dissolution of CdSe nanoparticles. The diffusion proceeds independently at different particles above f{sub t} and turns to cooperative mode below the threshold frequency. Due to this effect, information on spatial distribution of growing nuclei on electrode surface in early stages of electrodeposition can be obtained from potentiodynamic impedance spectra.

  6. Tailoring Si(100) substrate surfaces for GaP growth by Ga deposition: A low-energy electron microscopy study

    Energy Technology Data Exchange (ETDEWEB)

    Rienäcker, Michael; Borkenhagen, Benjamin, E-mail: b.borkenhagen@pe.tu-clausthal.de; Lilienkamp, Gerhard; Daum, Winfried [TU Clausthal, Institut für Energieforschung und Physikalische Technologien, Leibnizstraße 4, D-38678 Clausthal-Zellerfeld (Germany)

    2015-08-07

    For GaP-on-Si(100) heteroepitaxy, currently considered as a model system for monolithic integration of III–V semiconductors on Si(100), the surface steps of Si(100) have a major impact on the quality of the GaP film. Monoatomic steps cause antiphase domains in GaP with detrimental electronic properties. A viable route is to grow the III–V epilayer on single-domain Si(100) with biatomic steps, but preferably not at the expense of reduced terrace widths introduced by miscut substrates. We have performed in situ investigations of the influence of Ga deposition on the kinetics of surface steps and terraces of Si(100) at substrate temperatures above 600 °C by low-energy electron microscopy. Starting from nearly equally distributed T{sub A} and T{sub B} terraces of a two-domain Si(100) surface, submonolayer deposition of Ga results in a transformation into a surface dominated by T{sub A} terraces and biatomic D{sub A} steps. This transformation is reversible, and Si(100) with monoatomic steps is recovered upon termination of the Ga flux. Under conditions of higher coverages (but still below 0.25 monolayer), we observe restructuring into a surface with T{sub B} dominance, similar to the findings of Hara et al. [J. Appl. Phys. 98, 083515 (2005)]. The occurrence and mutual transformations of surface structures with different terrace and step structures in a narrow range of temperatures and Ga deposition rates is discussed.

  7. Low-energy ion beam-based deposition of gallium nitride.

    Science.gov (United States)

    Vasquez, M R; Wada, M

    2016-02-01

    An ion source with a remote plasma chamber excited by a 13.56 MHz radio frequency power was used for low-energy broad ion beam extraction. Optical emission spectral analyses showed the sputtering and postionization of a liquid gallium (Ga) target placed in a chamber separated from the source bombarded by argon (Ar) plasma guided by a bent magnetic field. In addition, an E × B probe successfully showed the extraction of low-energy Ga and Ar ion beams using a dual-electrode extractor configuration. By introducing dilute amounts of nitrogen gas into the system, formation of thin Ga-based films on a silicon substrate was demonstrated as determined from X-ray diffraction and X-ray reflectivity studies.

  8. Pulsed laser deposition of cluster-assembled films for catalysis and the photocatalysis relevant to energy and the environment

    Science.gov (United States)

    Miotello, A.; Patel, N.

    2013-08-01

    Nanoparticles (NPs) catalysts are under intense investigation in the catalysis community due to their exceptional activity and selective nature in catalytic processes as compared to the corresponding bulk counterpart, especially because of their large surface-to-volume atomic ratio, size- and shape-dependent properties, and high concentration of low-coordinated active surface sites. However, there is no general strategy to synthesize NPs of various materials with narrow size distribution, tailored properties, and desired morphologies. The development of a technique able to prepare NPs is thus a goal of great importance to avoid present trial and error approaches. Here we report on selected examples where pulsed laser deposition (PLD) technique greatly contributes toward NPs synthesis. Co NPs embedded in B matrix films have been synthesized by PLD technique by taking advantage of the phase explosion process of superheated liquid where a mixture of vapor and liquid droplets leave the irradiated target surface and get deposited on the substrate. The deposited NPs exhibit catalytic properties comparable to that of precious metals in hydrogen production by hydrolysis of NaBH4 and NH3BH3. These NPs, when supported on rough carbon film prepared by PLD, show about 30% increase in catalytic activity for H2 production as compared to unsupported NPs. Co3O4 NPs assembled coating has been produced by reactive PLD in oxygen atmosphere at various substrate temperatures from room temperature to 250 °C. It was proved that the Co3O4 NPs can be obtained in a single step at low temperatures with mixed disordered-nanocrystalline phase that is a relevant feature for catalysis. The Co3O4 NPs assembled thin coating, employed in degradation of methylene blue solution, in water, via photo Fenton reaction in presence of H2O2, exhibits significantly higher activity as compared to the corresponding homogeneous catalyst.

  9. Structure and properties of polyaniline nanocomposite coatings containing gold nanoparticles formed by low-energy electron beam deposition

    Science.gov (United States)

    Wang, Surui; Rogachev, A. A.; Yarmolenko, M. A.; Rogachev, A. V.; Xiaohong, Jiang; Gaur, M. S.; Luchnikov, P. A.; Galtseva, O. V.; Chizhik, S. A.

    2018-01-01

    Highly ordered conductive polyaniline (PANI) coatings containing gold nanoparticles were prepared by low-energy electron beam deposition method, with emeraldine base and chloroauric acid used as target materials. The molecular and chemical structure of the layers was studied by Fourier transform infrared, Raman, UV-vis and X-ray photoelectron spectroscopy. The morphology of the coatings was investigated by atomic force and transmission electron microscopy. Conductive properties were obtained by impedance spectroscopy method and scanning spreading resistance microscopy mode at the micro- and nanoscale. It was found that the emeraldine base layers formed from the products of electron-beam dispersion have extended, non-conductive polymer chains with partially reduced structure, with the ratio of imine and amine groups equal to 0.54. In case of electron-beam dispersion of the emeraldine base and chloroauric acid, a protoemeraldine structure is formed with conductivity 0.1 S/cm. The doping of this structure was carried out due to hydrochloric acid vapor and gold nanoparticles formed by decomposition of chloroauric acid, which have a narrow size distribution, with the most probable diameter about 40 nm. These gold nanoparticles improve the conductivity of the thin layers of PANI + Au composite, promoting intra- and intermolecular charge transfer of the PANI macromolecules aligned along the coating surface both at direct and alternating voltage. The proposed deposition method of highly oriented, conductive nanocomposite PANI-based coatings may be used in the direct formation of functional layers on conductive and non-conductive substrates.

  10. Nonperturbative QCD and elastic processes at CEBAF energies

    Energy Technology Data Exchange (ETDEWEB)

    Radyushkin, A.V. [Old Dominion Univ., Norfolk, VA (United States)]|[Continuous Electron Beam Accelerator Facility, Newport News, VA (United States)

    1994-04-01

    The author outlines how one can approach nonperturbative aspects of the QCD dynamics studying elastic processes at energies accessible at upgraded CEBAF. The author`s point is that, in the absence of a complete theory of the nonperturbative effects, a possible way out is based on a systematic use of the QCD factorization procedure which separates theoretically understood ({open_quotes}known{close_quotes}) short-distance effects and nonperturbative ({open_quotes}unknown{close_quotes}) long-distance ones. The latter include hadronic distribution amplitudes, soft components of hadronic form factors etc. Incorporating the QCD sum rule version of the QCD factorization approach, one can relate these nonperturbative functions to more fundamental objects, vacuum condensates, which accumulate information about the nonperturbative structure of the QCD vacuum. The emerging QCD sum rule picture of hadronic form factors is characterized by a dominant role of essentially nonperturbative effects in the few GeV region, with perturbative mechanisms starting to show up for momentum transfers Q{sup 2} closer to 10 GeV{sup 2} and higher. Thus, increasing CEBAF energy provides a unique opportunity for a precision study of interplay between the perturbative and nonperturbative phenomena in the QCD description of elastic processes.

  11. Thermoelectric energy harvesting for a solid waste processing toilet

    Science.gov (United States)

    Stokes, C. David; Baldasaro, Nicholas G.; Bulman, Gary E.; Stoner, Brian R.

    2014-06-01

    Over 2.5 billion people do not have access to safe and effective sanitation. Without a sanitary sewer infrastructure, self-contained modular systems can provide solutions for these people in the developing world and remote areas. Our team is building a better toilet that processes human waste into burnable fuel and disinfects the liquid waste. The toilet employs energy harvesting to produce electricity and does not require external electrical power or consumable materials. RTI has partnered with Colorado State University, Duke University, and Roca Sanitario under a Bill and Melinda Gates Foundation Reinvent the Toilet Challenge (RTTC) grant to develop an advanced stand-alone, self-sufficient toilet to effectively process solid and liquid waste. The system operates through the following steps: 1) Solid-liquid separation, 2) Solid waste drying and sizing, 3) Solid waste combustion, and 4) Liquid waste disinfection. Thermoelectric energy harvesting is a key component to the system and provides the electric power for autonomous operation. A portion of the exhaust heat is captured through finned heat-sinks and converted to electricity by thermoelectric (TE) devices to provide power for the electrochemical treatment of the liquid waste, pumps, blowers, combustion ignition, and controls.

  12. Corrosion Resistance of Ni-Based WC/Co Coatings Deposited by Spray and Fuse Process Varying the Oxygen Flow

    Science.gov (United States)

    Jiménez, H.; Olaya, J. J.; Alfonso, J. E.; Mtshali, C. B.; Pineda-Vargas, C. A.

    2017-10-01

    In this work, the effect of oxygen flow variation in the corrosion behavior of Ni-based WC/Co coatings deposited by spray and fuse process was investigated. The coatings were deposited on gray cast iron substrates using a Superjet Eutalloy thermal spraying gun. The morphology of the coatings was analyzed using scanning electron microscopy. The crystallographic phases were registered by x-ray diffraction (XRD), the diffraction patterns show the crystalline phases of the powder components with principal reflections for Ni and WC, the increase in flame temperature, due to the oxygen flow variation, generated amorphization in the nickel and an important crystallization of the planes (111) and (222) of WC as well as the decarburization of WC in W2C and W metallic. The corrosion behavior was investigated at room temperature in a 3.5% w/w aqueous solution of NaCl via potentiodynamic polarization. Electrochemical corrosion test showed that the coatings deposited under neutral flame conditions with an oxygen flow of 12.88 SCFH evidenced higher corrosion resistance. The chemical composition of the coatings and corrosion areas were analyzed by particle-induced x-ray emission, this technique permitting the corroboration of the decarburization process of WC determined by XRD and the formation of Cl structures.

  13. Low energy electron beam processing of YBCO thin films

    Energy Technology Data Exchange (ETDEWEB)

    Chromik, Š., E-mail: stefan.chromik@savba.sk [Institute of Electrical Engineering, SAS, Dúbravská cesta 9, 841 04 Bratislava (Slovakia); Camerlingo, C. [CNR-SPIN, Istituto Superconduttori, Materiali Innovativi e Dispositivi, via Campi Flegrei 34, 80078 Pozzuoli (Italy); Sojková, M.; Štrbík, V.; Talacko, M. [Institute of Electrical Engineering, SAS, Dúbravská cesta 9, 841 04 Bratislava (Slovakia); Malka, I.; Bar, I.; Bareli, G. [Department of Physics, Ben Gurion University of the Negev, P.O.B. 653, 84105 Beer Sheva (Israel); Jung, G. [Department of Physics, Ben Gurion University of the Negev, P.O.B. 653, 84105 Beer Sheva (Israel); Institute of Physics, Polish Academy of Sciences, Al. Lotników 32/46, 02-668 Warsaw (Poland)

    2017-02-15

    Highlights: • Improvement of superconducting properties of irradiated bridges under certain conditions. • 30 keV irradiation influence CuO{sub 2} planes as well as oxygen chains. • Direct confirmation of changes in oxygen chains using micro-Raman spectroscopy. • Possibility of electron writing. - Abstract: Effects of low energy 30 keV electron irradiation of superconducting YBa{sub 2}Cu{sub 3}O{sub 7−δ} thin films have been investigated by means of transport and micro-Raman spectroscopy measurements. The critical temperature and the critical current of 200 nm thick films initially increase with increasing fluency of the electron irradiation, reach the maximum at fluency 3 − 4 × 10{sup 20} electrons/cm{sup 2}, and then decrease with further fluency increase. In much thinner films (75 nm), the critical temperature increases while the critical current decreases after low energy electron irradiation with fluencies below 10{sup 20} electrons/cm{sup 2}. The Raman investigations suggest that critical temperature increase in irradiated films is due to healing of broken Cu−O chains that results in increased carrier’s concentration in superconducting CuO{sub 2} planes. Changes in the critical current are controlled by changes in the density of oxygen vacancies acting as effective pinning centers for flux vortices. The effects of low energy electron irradiation of YBCO turned out to result from a subtle balance of many processes involving oxygen removal, both by thermal activation and kick-off processes, and ordering of chains environment by incident electrons.

  14. Investigation of Boron Thermal Diffusion from Atmospheric Pressure Chemical Vapor Deposited Boron Silicate Glass for N-Type Solar Cell Process Application

    OpenAIRE

    Ikuo Kurachi; Kentaro Yoshioka

    2016-01-01

    An atmospheric pressure chemical vapor deposition (AP-CVD) system has been newly developed for boron silicate glass (BSG) film deposition dedicating to solar cell manufacturing. Using the system, thermal boron diffusion from the BSG film is investigated and confirmed in terms of process stability for surface property before BSG deposition and BSG thickness. No degradation in carrier lifetime is also confirmed. A boron diffusion simulator has been newly developed and demonstrated for optimizat...

  15. The effect of orientation difference in fused deposition modeling of ABS polymer on the processing time, dimension accuracy, and strength

    Science.gov (United States)

    Tanoto, Yopi Y.; Anggono, Juliana; Siahaan, Ian H.; Budiman, Wesley

    2017-01-01

    There are several parameters that must be set before manufacturing a product using 3D printing. These parameters include the orientation deposition of that product, type of material, form fill, fill density, and other parameters. The finished product of 3D printing has some responses that can be observed, measured, and tested. Some of those responses are the processing time, the dimensions of the end product, its surface roughness and the mechanical properties, i.e. its yield strength, ultimate tensile strength, and impact resistance. This research was conducted to study the relationship between process parameters of 3D printing machine using a technology of fused deposition modeling (FDM) and the generated responses. The material used was ABS plastic that was commonly used in the industry. Understanding the relationship between the parameters and the responses thus the resulting product can be manufactured to meet the user needs. Three different orientations in depositing the ABS polymer named XY(first orientation), YX (second orientation), and ZX (third orientation) were studied. Processing time, dimensional accuracy, and the product strength were the responses that were measured and tested. The study reports that the printing process with third orientation was the fastest printing process with the processing time 2432 seconds followed by orientation 1 and 2 with a processing time of 2688 and 2780 seconds respectively. Dimension accuracy was also measured from the width and the length of gauge area of tensile test specimens printed in comparison with the dimensions required by ASTM 638-02. It was found that the smallest difference was in thickness dimension, i.e. 0.1 mm thicker in printed sample using second orientation than as required by the standard. The smallest thickness deviation from the standard was measured in width dimension of a sample printed using first orientation (0.13 mm). As with the length dimension, the closest dimension to the standard was

  16. A novel Ag catalyzation process using swelling impregnation method for electroless Ni deposition on Kevlar® fiber

    Science.gov (United States)

    Pang, Hongwei; Bai, Ruicheng; Shao, Qinsi; Gao, Yufang; Li, Aijun; Tang, Zhiyong

    2015-12-01

    A novel Ag catalyzation process using swelling impregnation pretreatment method was developed for electroless nickel (EN) deposition on Kevlar fiber. Firstly, the fiber was immersed into an aqueous dimethylsulfoxide (DMSO) solution of silver nitrate to impart silver nitrate into the inner part of the fiber near the surface. Subsequently silver nitrate was reduced to metal silver nanoparticles on the fiber surface by treatment with aqueous solution of sodium borohydride. After electroless plating, a dense and homogeneous nickel coating was obtained on the fiber surface. The silver nanoparticles formed at the fiber surface functioned as a catalyst for electroless deposition as well as an anchor for the plated layer. The study also revealed that the incorporation of surfactant sodium dodecyl sulfate (SDS) in electroless nickel plating bath can enhance the adhesion strength of EN layer with the fiber surface and minimize the surface roughness of the EN coating. The Ni plated Kevlar fiber possessed excellent corrosion resistance and high tensile strength.

  17. A modular reactor design for in situ synchrotron x-ray investigation of atomic layer deposition processes

    Science.gov (United States)

    Klug, Jeffrey A.; Weimer, Matthew S.; Emery, Jonathan D.; Yanguas-Gil, Angel; Seifert, Sönke; Schlepütz, Christian M.; Martinson, Alex B. F.; Elam, Jeffrey W.; Hock, Adam S.; Proslier, Thomas

    2015-11-01

    Synchrotron characterization techniques provide some of the most powerful tools for the study of film structure and chemistry. The brilliance and tunability of the Advanced Photon Source allow access to scattering and spectroscopic techniques unavailable with in-house laboratory setups and provide the opportunity to probe various atomic layer deposition (ALD) processes in situ starting at the very first deposition cycle. Here, we present the design and implementation of a portable ALD instrument which possesses a modular reactor scheme that enables simple experimental switchover between various beamlines and characterization techniques. As first examples, we present in situ results for (1) X-ray surface scattering and reflectivity measurements of epitaxial ZnO ALD on sapphire, (2) grazing-incidence small angle scattering of MnO nucleation on silicon, and (3) grazing-incidence X-ray absorption spectroscopy of nucleation-regime Er2O3 ALD on amorphous ALD alumina and single crystalline sapphire.

  18. Optical evidence for reactive processes when embedding Cu nanoparticles in Al(2)O(3) by pulsed laser deposition.

    Science.gov (United States)

    Serna, R; Suárez-García, A; Afonso, C N; Babonneau, D

    2006-09-28

    The optical response of nanocomposite thin films formed by Cu nanoparticles (NPs) embedded in amorphous aluminium oxide (Al(2)O(3)) prepared by pulsed laser deposition (PLD) in vacuum is studied in order to investigate the possible existence of reactive processes on the Cu NPs during their covering with Al(2)O(3). The study is performed as a function of the laser fluence on the Al(2)O(3) target (0.6-4.6 J cm(-2)), while the laser fluence for Cu ablation is kept constant (1.8 J cm(-2)). The structural analysis of the films shows that they are formed by a high density of NPs with average dimensions in the 4.9-5.9 nm range. The optical response of the films has been followed in situ by real-time reflectivity measurements at 633 nm and after deposition by transmission measurements as a function of wavelength around the surface plasmon resonance (SPR). For low laser fluences on the Al(2)O(3) target, the absorption spectrum is dominated by a well-defined SPR absorption band at 1.9 eV. As the laser fluence is increased, the intensity of the absorption band associated with the SPR decreases and shifts to 2.1 eV. The films deposited at low fluences contain metallic Cu NPs and, as the laser fluence increases sputtering of Cu from the NPs and mixing of the species from the Al(2)O(3) deposition with the Cu from the NPs surface takes place. The latter process leads to the formation of an Al-Cu oxide cover on the Cu NPs. The present results provide evidence for mixing of species from the host and Cu at the surface of the NPs, and it is shown how the degree of mixing depends on the laser fluence used to ablate the Al(2)O(3) host target.

  19. Efficiency evaluation of oxygen enrichment in energy conversion processes

    Energy Technology Data Exchange (ETDEWEB)

    Bomelburg, H.J.

    1983-12-01

    The extent to which energy conversion efficiencies can be increased by using oxygen or oxygen-enriched air for combustion was studied. Combustion of most fuels with oxygen instead of air was found to have five advantages: increases combustion temperature and efficiency, improves heat transfer at high temperatures, reduces nitrous oxide emissions, permits a high ration of exhaust gas recirculation and allows combustion of certain materials not combustible in air. The same advantages, although to a lesser degree, are apparent with oxygen-enriched air. The cost-effectiveness of the process must necessarily be improved by about 10% when using oxygen instead of air before such use could become justifiable on purely economic terms. Although such a modest increase appears to be attainable in real situations, this study ascertained that it is not possible to generally assess the economic gains. Rather, each case requires its own evaluation. For certain processes industry has already proven that the use of oxygen leads to more efficient plant operation. Several ideas for essentially new applications are described. Specifically, when oxygen is used with exhaust gas recirculation in external or internal combustion engines. It appears also that the advantages of pulse combustion can be amplified further if oxygen is used. When burning wet fuels with oxygen, direct steam generation becomes possible. Oxygen combustion could also improve processes for in situ gasification of coals, oil shales, peats, and other wet fuels. Enhanced oil recovery by fire flooding methods might also become more effective if oxygen is used. The cold energy contained in liquid oxygen can be substantially recovered in the low end of certain thermodynamic cycles. Further efforts to develop certain schemes for using oxygen for combustion appear to be justified from both the technical and economic viewpoints.

  20. Optimisation of logistics processes of energy grass collection

    Science.gov (United States)

    Bányai, Tamás.

    2010-05-01

    The collection of energy grass is a logistics-intensive process [1]. The optimal design and control of transportation and collection subprocesses is a critical point of the supply chain. To avoid irresponsible decisions by right of experience and intuition, the optimisation and analysis of collection processes based on mathematical models and methods is the scientific suggestible way. Within the frame of this work, the author focuses on the optimisation possibilities of the collection processes, especially from the point of view transportation and related warehousing operations. However the developed optimisation methods in the literature [2] take into account the harvesting processes, county-specific yields, transportation distances, erosion constraints, machinery specifications, and other key variables, but the possibility of more collection points and the multi-level collection were not taken into consideration. The possible areas of using energy grass is very wide (energetically use, biogas and bio alcohol production, paper and textile industry, industrial fibre material, foddering purposes, biological soil protection [3], etc.), so not only a single level but also a multi-level collection system with more collection and production facilities has to be taken into consideration. The input parameters of the optimisation problem are the followings: total amount of energy grass to be harvested in each region; specific facility costs of collection, warehousing and production units; specific costs of transportation resources; pre-scheduling of harvesting process; specific transportation and warehousing costs; pre-scheduling of processing of energy grass at each facility (exclusive warehousing). The model take into consideration the following assumptions: (1) cooperative relation among processing and production facilties, (2) capacity constraints are not ignored, (3) the cost function of transportation is non-linear, (4) the drivers conditions are ignored. The

  1. Causal knowledge extraction by natural language processing in material science: a case study in chemical vapor deposition

    Directory of Open Access Journals (Sweden)

    Yuya Kajikawa

    2006-11-01

    Full Text Available Scientific publications written in natural language still play a central role as our knowledge source. However, due to the flood of publications, the literature survey process has become a highly time-consuming and tangled process, especially for novices of the discipline. Therefore, tools supporting the literature-survey process may help the individual scientist to explore new useful domains. Natural language processing (NLP is expected as one of the promising techniques to retrieve, abstract, and extract knowledge. In this contribution, NLP is firstly applied to the literature of chemical vapor deposition (CVD, which is a sub-discipline of materials science and is a complex and interdisciplinary field of research involving chemists, physicists, engineers, and materials scientists. Causal knowledge extraction from the literature is demonstrated using NLP.

  2. Tailoring out-of-plane magnetic properties of pulsed laser deposited FePt thin films by changing laser energy fluence

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ying; Tan, T.L.; Tan, K.S.; Lee, P. [NSSE, NIE, Nanyang Technological University, 1 Nanyang Walk, Singapore 637616 (Singapore); Liu, Hai; Yadian, Boluo; Hu, Ge; Huang, Yizhong; Ramanujan, R.V. [School of Material Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore 639798 (Singapore); Rawat, R.S., E-mail: rajdeep.rawat@nie.edu.sg [NSSE, NIE, Nanyang Technological University, 1 Nanyang Walk, Singapore 637616 (Singapore)

    2014-10-01

    Highlights: • Laser energy fluence (LEF) effect on composition, microstructure and magnetism. • Enhancing out-of-plane magnetic properties by tailoring LEF on target surface. • Higher LEF results in more energetic plasma species causing vacancy defects. • Formation of vacancy defect in FePt thin films leads to improved magnetic properties. • Best out-of-plane magnetic properties are achieved with medium LEF. - Abstract: Magnetic properties of pulsed laser deposited (PLD) FePt thin films are investigated at three different laser energy fluences of 51, 136 and 182 J/cm{sup 2}. Deposition at lower laser energy fluence (51 J/cm{sup 2}) yields softer out-of-plane coercivity (≤0.4 kG), whereas deposition at higher laser energy fluence (136 and 182 J/cm{sup 2}) results in harder out-of-plane coercivity (≥5.0 kG). The improved coercivity is found to be attributed to the formation of vacancy defects in thin films, which is indicated by stress change from tensile to compressive form with increasing laser energy fluence. Maximum out-of-plane saturated magnetization of 615 emu/cm{sup 3} and remanent squareness ratio of 0.88 are achieved for 16 nm thick FePt thin films deposited at moderate laser energy fluence of 136 J/cm{sup 2}, making them suitable for high density perpendicular data storage applications.

  3. Strategic investment of embodied energy during the architectural planning process

    Directory of Open Access Journals (Sweden)

    Linda Hildebrand

    2014-05-01

    Full Text Available Background and motivation Building industry impacts natural cycles and has potential for optimization. While impairment on nature reached a new dimension already some three centuries ago the building industry started to realize the dependency in the second half of the 20th century. With LCA method all life cycle phases can be monitored and the environmental impact of each can be quantified. The energy consuming and emission generating components in the building context can be distinguished in the groups transport, operation and material. An architect deals with the operational energy and the building substance. With nearly zero (not renewable energy for operation an ecological building is defined by the building substance. Evaluation of the building substance While the building structure accounts for the highest share of embodied energy and GWP, the facade offers high potential for optimisation. This potential is even higher when considering a long (50-100 years usage life span; the building structure remains while the (non load-bearing facade is object to exchange cycles. Findings and their integration into the architectural planning process The city is a depot for resources and we (it involves a variety of professions need to learn how to organize it. Modularity, light construction, the use of renewable materials and mono materials are also interesting fields which are looked at from a different point of view. They are relevant for all building elements. Although they are not initially invented to reduce the ecological impact of the built environment, they show potential to do so. The facade is the essential parameter for the resource-efficiency of a building as it is exchanged and binds relevant amounts of material. Impact can be made within this element due to its high variation in construction and materialization. The material cycles need to become smaller and the gaps – landfill or downcycling need to be closed. The use of resources will

  4. On-Demand Spare Parts for the Marine Industry with Directed Energy Deposition : Propeller Use Case

    NARCIS (Netherlands)

    Ya, Wei; Hamilton, Kelvin; Meboldt, Mirko; Klahn, Christoph

    2017-01-01

    As additive manufacturing (AM) gains greater industrial exposure, there is a drive towards defining practical, high-value processes and products. Defining viable business cases is critical to ensure successful technology adoption. Given the marine industry’s slow uptake of AM, the potential of Wire

  5. Dietary energy source affecting fat deposition mechanism, muscle fiber metabolic and overall meat quality

    Directory of Open Access Journals (Sweden)

    M. Al-Hijazeen

    2017-03-01

    Full Text Available A study was conducted to investigate the effect of two dietary energy sources, soy bean oil, and sucrose on regulatory mechanisms of meat preservation. Twenty one day-old Hubbard commercial broilers were randomly allocated into two dietary treatment groups with six replicates per treatment, and four broilers per replicate. All birds were coded for the influence of energy source: fat based diet (FD, and sugar based diet (SD. Formulated grower diets were isonitrogenous and isocaloric. The chickens were slaughtered and then boneless, skinless ground chicken tight meat was prepared. Both raw and cooked meats were analyzed for lipid and protein oxidation, and sensory panel evaluation. In addition, meat from the small muscles of the raw thigh was used to evaluate other meat quality characteristics. Proximate analyses showed no significant differences between both dietary treatments on protein, ash and moisture percentage values. Meat samples of the group that was fed FD showed higher significant values of both TBARS and total carbonyl at day 7 of storage time. However, samples of the second group (Fed SD showed lower values of both ultimate pH and water separation % using raw thigh meat. The effect of FD treatment on the meat composition appeared clearly especially on fat percentage content. In addition, meat samples obtained from chickens fed SD showed better significant values of the overall acceptability attribute. According to the current findings, sucrose could be an excellent alternative to oil in dietary broilers which improved the meat preservation bio-system, and post-mortem storage stability.

  6. 4{pi} studies of the 1.8-4.8 GeV {sup 3}He+{sup nat}Ag, {sup 197}Au reactions. I. Energy deposition

    Energy Technology Data Exchange (ETDEWEB)

    Morley, K.B.; Kwiatkowski, K.; Bracken, D.S.; Renshaw Foxford, E. [Indiana Univ., Bloomington, IN (United States). Dept. of Chemistry; Legrain, R.; Pollacco, E.C.; Volant, C. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. d`Astrophysique, de la Physique des Particules, de la Physique Nucleaire et de l`Instrumentation Associee; Korteling, R.G. [Simon Fraser Univ., Burnaby, BC (Canada). Dept. of Chemistry; Breuer, H. [Maryland Univ., College Park, MD (United States). Dept. of Physics; Brzychczyk, J. [Jagellonian Univ., Krakow (Poland). Inst. of Physics

    1996-01-01

    The 4{pi} detector ISiS has been used to measure light-charged particles and intermediate-mass-fragments emitted in the 1.8-4.8 GeV {sup 3}He+{sup nat}Ag, {sup 197}Au reactions. Ejectile multiplicity and total event kinetic energy distribution scale systematically with projectile energy and target mass, except for the {sup nat}Ag target at 3.6 and 4.8 GeV. For this system, a saturation in deposition energy is indicated by the data, suggesting the upper projectile energy for stopping has been reached. Maximum deposition energies of {approx}950 MeV for the {sup nat}Ag target and {approx}1600 MeV for the {sup 197}Au target are inferred from the data. Comparison of the experimental distributions with intranuclear cascade predictions shows qualitative agreement. (author). Submitted to Physical Review, C (US); 46 refs.

  7. Process of optimization of district heat production by utilizing waste energy from metallurgical processes

    Science.gov (United States)

    Konovšek, Damjan; Fužir, Miran; Slatinek, Matic; Šepul, Tanja; Plesnik, Kristijan; Lečnik, Samo

    2017-07-01

    In a consortium with SIJ (Slovenian Steel Group), Metal Ravne, the local community of Ravne na Koro\\vskem and the public research Institut Jožef Stefan, with its registered office in Slovenia, Petrol Energetika, d.o.o. set up a technical and technological platform of an innovative energy case for a transition of steel industry into circular economy with a complete energy solution called »Utilization of Waste Heat from Metallurgical Processes for District Heating of Ravne na Koro\\vskem. This is the first such project designed for a useful utilization of waste heat in steel industry which uses modern technology and innovative system solutions for an integration of a smart, efficient and sustainable heating and cooling system and which shows a growth potential. This will allow the industry and cities to make energy savings, to improve the quality of air and to increase the benefits for the society we live in. On the basis of circular economy, we designed a target-oriented co-operation of economy, local community and public research institute to produce new business models where end consumers are put into the centre. This innovation opens the door for steel industry and local community to a joint aim that is a transition into efficient low-carbon energy systems which are based on involvement of natural local conditions, renewable energy sources, the use of waste heat and with respect for the principles of sustainable development.

  8. Practical aspects of plasma processes in thermionic energy converters

    Science.gov (United States)

    Rasor, N. S.; Hansen, L. K.; Fitzpatrick, G. O.; Britt, E. J.

    1975-01-01

    Over a decade of cesium vapor thermionic converter research has yielded sufficient understanding of the basic plasma processes to permit application of this understanding to improvement of converter performance. A performance index is defined which relates such converter improvements directly to increases in system performance. A prime practical objective of current research is to reduce or eliminate the arc potential drop presently required to sustain the plasma in the ignited cesium diode. This will substantially increase the energy conversion efficiency, and will permit operation at substantially lower emitter temperatures without requiring lower collector (heat rejection) temperature. Present work is concentrating on evaluating and reducing to practice the several methods employing auxiliary ion sources to eliminate the arc drop which were demonstrated over a decade ago: i.e., various ignited and unignited triode concepts, and the pulse-enhanced diode and triode. These methods are reviewed in light of present understanding and recent experimental data.

  9. The High Energy Asymptotics of Scattering Processes in QCD

    Energy Technology Data Exchange (ETDEWEB)

    Enberg, Rikard; Golec-Biernat, K.; Munier, S.

    2005-05-12

    High energy scattering in the QCD parton model was recently shown to be a reaction-diffusion process, and thus to lie in the universality class of the stochastic Fisher-Kolmogorov-Petrovsky-Piscounov equation. We recall that the latter appears naturally in the context of the parton model. We provide a thorough numerical analysis of the mean field approximation, given in QCD by the Balitsky-Kovchegov equation. In the framework of a simple stochastic toy model that captures the relevant features of QCD, we discuss and illustrate the universal properties of such stochastic models. We investigate in particular the validity of the mean field approximation and how it is broken by fluctuations. We find that the mean field approximation is a good approximation in the initial stages of the evolution in rapidity.

  10. Energy Efficient Pump Control for an Offshore Oil Processing System

    DEFF Research Database (Denmark)

    Yang, Zhenyu; Soleiman, Kian; Løhndorf, Bo

    2012-01-01

    The energy efficient control of a pump system for an offshore oil processing system is investigated. The seawater is lifted up by a pump system which consists of three identical centrifugal pumps in parallel, and the lifted seawater is used to cool down the crude oil flowing out of a threephase...... separator on one of the Danish north-sea platform. A hierarchical pump-speed control strategy is developed for the considered system by minimizing the pump power consumption subject to keeping a satisfactory system performance. The proposed control strategy consists of online estimation of some system...... operating parameters, optimization of pump configurations, and a real-time feedback control. Comparing with the current control strategy at the considered system, where the pump system is on/off controlled, and the seawater flows are controlled by a number of control valves, the proposed control strategy...

  11. Energy Performance of Verandas in the Building Retrofit Process

    Directory of Open Access Journals (Sweden)

    Rossano Albatici

    2016-05-01

    Full Text Available Passive solar elements for both direct and indirect gains, are systems used to maintain a comfortable living environment while saving energy, especially in the building energy retrofit and adaptation process. Sunspaces, thermal mass and glazing area and orientation have been often used in the past to guarantee adequate indoor conditions when mechanical devices were not available. After a period of neglect, nowadays they are again considered as appropriate systems to help face environmental issues in the building sector, and both international and national legislation takes into consideration the possibility of including them in the building planning tools, also providing economic incentives. Their proper design needs dynamic simulation, often difficult to perform and time consuming. Moreover, results generally suffer from several uncertainties, so quasi steady-state procedures are often used in everyday practice with good results, but some corrections are still needed. In this paper, a comparative analysis of different solutions for the construction of verandas in an existing building is presented, following the procedure provided by the slightly modified and improved Standard EN ISO 13790:2008. Advantages and disadvantages of different configurations considering thermal insulation, windows typology and mechanical ventilation systems are discussed and a general intervention strategy is proposed. The aim is to highlight the possibility of using sunspaces in order to increase the efficiency of the existing building stock, considering ease of construction and economic viability.

  12. Thin and flexible Ni-P based current collectors developed by electroless deposition for energy storage devices

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Haoran, E-mail: haoran.wu@mail.utoronto.ca; Susanto, Amelia; Lian, Keryn

    2017-02-01

    Highlights: • A PET metallized by electroless nickel was developed as flexible current collector. • The Ni-PET current collector showed good conductivity and chemical stability. • The flexible nanocarbon electrodes with Ni-PET exhibited capacitive behavior. • The Ni-PET enabled electrodes performed nicely in liquid and solid supercapacitors. - Abstract: A PET film metalized by electroless nickel deposition was demonstrated as thin and flexible current collector for energy storage devices. The resultant nickel-on-PET film (Ni-PET) can be used both as current collector for electrochemical capacitors and as electrode for thin film batteries. The composition of Ni-PET was characterized by EDX and XPS. The electrochemical performance of the Ni-PET current collector was similar to Ni foil but with less hydrogen evolution at low potential. The Ni-PET film exhibited better flexibility than a metallic Ni foil. Carbon nanotubes were coated on a Ni-PET substrate to form an electrochemical capacitor electrode which exhibited high chemical stability in both liquid and solid electrolytes, showing strong promise for solid energy storage devices.

  13. Crevasse splay processes and deposits in an ancient distributive fluvial system: The lower Beaufort Group, South Africa

    Science.gov (United States)

    Gulliford, Alice R.; Flint, Stephen S.; Hodgson, David M.

    2017-08-01

    Up to 12% of the mud-prone, ephemeral distributive fluvial system stratigraphy in the Permo-Triassic lower Beaufort Group, South Africa, comprises tabular fine-grained sandstone to coarse-grained siltstone bodies, which are interpreted as proximal to distal crevasse splay deposits. Crevasse splay sandstones predominantly exhibit ripple to climbing ripple cross-lamination, with some structureless and planar laminated beds. A hierarchical architectural scheme is adopted, in which 1 m thick crevasse splay elements extend for tens to several hundreds of meters laterally, and stack with other splay elements to form crevasse splay sets up to 4 m thick and several kilometers in width and length. Paleosols and nodular horizons developed during periods, or in areas, of reduced overbank flooding are used to subdivide the stratigraphy, separating crevasse splay sets. Deposits from crevasse splays differ from frontal splays as their proximal deposits are much thinner and narrower, with paleocurrents oblique to the main paleochannel. In order for crevasse splay sets to develop, the parent channel belt and the location where crevasse splays form must stay relatively fixed during a period of multiple flood events. Beaufort Group splays have similar geometries to those of contemporary perennial rivers but exhibit more lateral variability in facies, which is interpreted to be the result of more extreme fluctuations in discharge regime. Sharp-based crevasse splay packages are associated with channel avulsion, but most are characterized by a gradual coarsening upward, interpreted to represent progradation. The dominance of progradational splays beneath channel belt deposits may be more characteristic of progradational stratigraphy in a distributive fluvial system rather than dominated by avulsion processes in a trunk river system. This stratigraphic motif may therefore be an additional criterion for recognition of distributive fluvial systems in the ancient record.

  14. Linking Transformational Materials and Processing for an Energy-Efficient and Low-Carbon Economy, 2010

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, Warren H. [Minerals, Metals, and Materials Society (TMS), Warrendale, PA (United States); Brindle, Ross [Nexight Group, LLC, Silver Spring, MD (United States); James, Mallory [Energetics Inc., Columbia, MD (United States); Justiniano, Mauricio [Energetics Inc., Columbia, MD (United States); Sabouni, Ridah [Energetics Inc., Columbia, MD (United States); Seader, Melanie [Energetics Inc., Columbia, MD (United States); Ruch, Jennifer [Energetics Inc., Columbia, MD (United States); Andres, Howard [Energetics Inc., Columbia, MD (United States); Zafar, Muhammad [Energetics Inc., Columbia, MD (United States)

    2010-06-01

    The Energy Materials Blue Ribbon Panel, representing experts from industry, academia, and government, identifies new materials and processing breakthroughs that could lead to transformational advances in energy efficiency, energy security, and carbon reduction.

  15. Analysis of the Influence of the Use of Cutting Fluid in Hybrid Processes of Machining and Laser Metal Deposition (LMD

    Directory of Open Access Journals (Sweden)

    Magdalena Cortina

    2018-02-01

    Full Text Available Hybrid manufacturing processes that combine additive and machining operations are gaining relevance in modern industry thanks to the capability of building complex parts with minimal material and, many times, with process time reduction. Besides, as the additive and subtractive operations are carried out in the same machine, without moving the part, dead times are reduced and higher accuracies are achieved. However, it is not clear whether the direct material deposition after the machining operation is possible or intermediate cleaning stages are required because of the possible presence of residual cutting fluids. Therefore, different Laser Metal Deposition (LMD tests are performed on a part impregnated with cutting fluid, both directly and after the removal of the coolant by techniques such as laser vaporizing and air blasting. The present work studies the influence of the cutting fluid in the LMD process and the quality of the resulting part. Resulting porosity is evaluated and it is concluded that if the part surface is not properly clean after the machining operation, deficient clad quality can be obtained in the subsequent laser additive operation.

  16. Numerical Investigation of Simultaneously Deposition and Re-Entrainment Fouling Processes in Corrugated Tubes by Coupling CFD and DEM

    DEFF Research Database (Denmark)

    Hærvig, Jakob; Condra, Thomas Joseph; Sørensen, Kim

    to fouling deposit than others, detailed fouling considerations have to be taken into account in the initial design process of new heat exchangers. This study presents initial simulations of particulate fouling in the corrugated tube heat exchanger type. Using a mechanistic Euler-Lagrange approach, where...... Computational Fluid Dynamics (CFD) software OpenFOAM is coupled to the Discrete Element Method (DEM) software LIGGGHTS using the coupling software CFDEM. A four-way coupling is used to model fluid-particle and particle-particle interactions and thereby allowing for a particle fouling layer to build up along...

  17. Energy recovery from waste processing; La recuperation de l'energie issue du traitement des dechets

    Energy Technology Data Exchange (ETDEWEB)

    Prevot, H.

    2000-07-15

    This report discusses the feasibility of energy production by waste reprocessing. After an analysis of the situation, the different steps of the methane and gas production, are detailed. Many scenari of energy efficiency are compared. The report proposes also solutions to enhance the treatment units of energy production. Propositions are discussed around five main axis: the energy improvement and the product improvement, the safety and the public health, the compensation by economical tools of the greenhouse effect impacts, the competition equilibrium between energy produced by the wastes and other energy forms and the decrease of the processing cost of wastes producing energy. (A.L.B.)

  18. Development Status of a CVD System to Deposit Tungsten onto UO2 Powder via the WCI6 Process

    Science.gov (United States)

    Mireles, O. R.; Kimberlin, A.; Broadway, J.; Hickman, R.

    2014-01-01

    Nuclear Thermal Propulsion (NTP) is under development for deep space exploration. NTP's high specific impulse (> 850 second) enables a large range of destinations, shorter trip durations, and improved reliability. W-60vol%UO2 CERMET fuel development efforts emphasize fabrication, performance testing and process optimization to meet service life requirements. Fuel elements must be able to survive operation in excess of 2850 K, exposure to flowing hydrogen (H2), vibration, acoustic, and radiation conditions. CTE mismatch between W and UO2 result in high thermal stresses and lead to mechanical failure as a result UO2 reduction by hot hydrogen (H2) [1]. Improved powder metallurgy fabrication process control and mitigated fuel loss can be attained by coating UO2 starting powders within a layer of high density tungsten [2]. This paper discusses the advances of a fluidized bed chemical vapor deposition (CVD) system that utilizes the H2-WCl6 reduction process.

  19. Deposition SnO(2)/nitrogen-doped graphene nanocomposites on the separator: a new type of flexible electrode for energy storage devices.

    Science.gov (United States)

    Liang, Junfei; Cai, Zhi; Tian, Yu; Li, Lidong; Geng, Jianxin; Guo, Lin

    2013-11-27

    It is currently very urgent to develop flexible energy storage devices because of the growing academic interest in and strong technical demand of flexible electronics. Exploration of high-performance electrode materials and a corresponding assembly method for fabrication of flexible energy storage devices plays a critical role in fulfilling this demand. Here, we have developed a facile, economic, and green hydrothermal process to synthesize ultrasmall SnO2 nanocrystallites/nitrogen-doped graphene nanocomposites (USNGs) as a high-performance electrode material for Li-ion batteries (LIBs). Furthermore, using the glass microfiber filters (GMFs) as supporting substrate, the novel flexible USNG-GMF bilayered films have been prepared by depositing the as-prepared USNG on GMF through a simple vacuum filtration. Significantly, for the first time, the flexible USNG-GMF bilayered films have directly been used for assembling LIBs, where the GMF further functions as a separator. The obtained highly robust, binder-free, conducting agent-free, and current collector-free new type of flexible electrodes show excellent LIB performance.

  20. Effective motion design applied to energy-efficient handling processes

    Energy Technology Data Exchange (ETDEWEB)

    Brett, Tobias

    2013-10-01

    Industrial robots are available in a large variety of mechanical alternatives regarding size, motor power, link length ratio or payload. The four major types of serial kinematics dominating the market are complemented by various parallel kinematics for special purpose. In contrast, few other path planning alternatives are applied in industrial robotics which are based on similar analytic solution principles. The objective of this thesis is to develop a systematic design method for artifacts in motion, to integrate motion design and mechanical design to enable new processes for production. For each design, a theoretical benchmark is developed, which cannot be attained by conventional robots in principle. A key performance indicator enables to measure the degree of goal achievement towards the benchmark during all design phases. Motion behaviors are identified on a local level by dynamic systems modeling and are integrated into new global behavior featuring a new quality, suitable for exceeding the design benchmark in industrial processes. Two exemplary handling robot designs are presented. The first concept enables motion behavior to consume less electrical power than kinetic energy transferred to and from its payload during motion. The second concept enables motion with four degrees of freedom by single motor stimulation, reducing idle power consumption on factor 4 towards conventional robots.

  1. Estimation of energy efficiency of the process of osmotic dehydration of pork meat

    OpenAIRE

    Filipović, Vladimir; Ćurčić, Biljana; Nićetin, Milica; Knežević, Violeta; Lević, Ljubinko; Pezo, Lato

    2014-01-01

    Osmotic dehydration is a low-energy process since water removal from the raw material is without phase change. The goal of this research is to estimate energy efficiency of the process of osmotic dehydration of pork meat at three different process temperatures, in three different osmotic solutions and in co- and counter-current processes. In order to calculate energy efficiency of the process of osmotic dehydration, convective drying was used as a base process for comparison. Levels of the sa...

  2. Bismuth mineral inclusions in gold-bearing magnetite from the giant Beiya gold deposit, SW China: insights into mineralization process

    Science.gov (United States)

    Zhou, Haoyang; Sun, Xiaoming

    2017-04-01

    Bismuth minerals are commonly found in a wide range of gold deposits and could offer valuable information on the process of gold mineralization. This is because Bi minerals always show immediate association with gold and are sensitive to chemical-physical variations (Afifi et al., 1988). Specifically, native bismuth has a melting point of 271°C and could melt at lower temperatures when gold is added (Okamoto et al,, 1983). It has been verified that Bi melt could efficiently scavenge gold from hydrothermal fluids (Tooth et al., 2008, 2011). The Beiya deposit, situated in the Sanjiang Tethyan tectonic domain in the southwestern China, is one of the largest gold deposits in China 10.4 Moz Au @ 2.47g/t). Located along the contacts between a 36 Ma quartz syenite porphyry and the Triassic limestones, the deposit contains abundant massive Au-bearing magnetite ores, which are considered as a product of skarn mineralization. However, the pivotal processes accounting for the huge accumulation of gold resource at Beiya area are poorly constrained. In the massive magnetite ores, abundant native gold was observed to be present as submicron-scale inclusions hosted by magnetite (Zhou et al., 2017). We also noted that abundant Bi minerals occur within these ores (Zhou et al., 2016), which provide critical clues to reveal the processes of gold mineralization. An assemblage of Bi minerals, composed of native bismuth, maldonite and bismuthinite, is present as tiny inclusions in these Au-bearing magnetite grains. Mineralogical study illustrates the encapsulation of native bismuth and maldonite as melts during magnetite growth, which is also supported by the ore-forming temperatures over 300°C derived from previous fluid inclusions study (He et al., 2016). Our thermodynamic modeling demonstrates that Bi melts scavenged gold from hydrothermal fluids. Subsequently, sulfidation of Bi melts resulted in precipitation of gold, which was captured by growing magnetite. We thus propose that

  3. Low-temperature atomic layer deposition of TiO{sub 2} thin layers for the processing of memristive devices

    Energy Technology Data Exchange (ETDEWEB)

    Porro, Samuele, E-mail: samuele.porro@polito.it; Conti, Daniele; Guastella, Salvatore; Ricciardi, Carlo [Applied Science and Technology Department, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy); Jasmin, Alladin; Pirri, Candido F. [Applied Science and Technology Department, Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino, Italy and Center for Space Human Robotics@PoliTo, Istituto Italiano di Tecnologia, C.so Trento 21, 10129 Torino (Italy); Bejtka, Katarzyna; Perrone, Denis; Chiolerio, Alessandro [Center for Space Human Robotics@PoliTo, Istituto Italiano di Tecnologia, C.so Trento 21, 10129 Torino (Italy)

    2016-01-15

    Atomic layer deposition (ALD) represents one of the most fundamental techniques capable of satisfying the strict technological requirements imposed by the rapidly evolving electronic components industry. The actual scaling trend is rapidly leading to the fabrication of nanoscaled devices able to overcome limits of the present microelectronic technology, of which the memristor is one of the principal candidates. Since their development in 2008, TiO{sub 2} thin film memristors have been identified as the future technology for resistive random access memories because of their numerous advantages in producing dense, low power-consuming, three-dimensional memory stacks. The typical features of ALD, such as self-limiting and conformal deposition without line-of-sight requirements, are strong assets for fabricating these nanosized devices. This work focuses on the realization of memristors based on low-temperature ALD TiO{sub 2} thin films. In this process, the oxide layer was directly grown on a polymeric photoresist, thus simplifying the fabrication procedure with a direct liftoff patterning instead of a complex dry etching process. The TiO{sub 2} thin films deposited in a temperature range of 120–230 °C were characterized via Raman spectroscopy and x-ray photoelectron spectroscopy, and electrical current–voltage measurements taken in voltage sweep mode were employed to confirm the existence of resistive switching behaviors typical of memristors. These measurements showed that these low-temperature devices exhibit an ON/OFF ratio comparable to that of a high-temperature memristor, thus exhibiting similar performances with respect to memory applications.

  4. Studying the Adsorption Process of Riboflavin on Silver-Deposited Fe3O4 Nanoparticles

    Directory of Open Access Journals (Sweden)

    Morteza Akhond

    2016-12-01

    Full Text Available The adsorption characteristics of riboflavin onto silver-deposited iron oxide magnetic nanoparticles (Ag/Fe3O4 have been described. Characterization of the synthesized Ag/Fe3O4 nanoparticles was achieved by FTIR spectra, TEM image and XRD pattern. The influence of several experimental parameters such as nanoparticles dosage, pH of the sample solution, different orientations of the riboflavin molecules toward Ag/Fe3O4 surface, riboflavin concentration, contact time of the reagents, temperature, ionic strength and presence of halide anions were studied. Experimental data indicated that Ag/Fe3O4 nanoparticles adsorb more than 90% of riboflavin under the optimum experimental conditions of the adsorbent dosage of 4.0 mg, a pH of 6.0, and a contact time of 2.0 min, when an initial riboflavin concentration of 0.02 mM is used. The results revealed that the presence of halide anions lower the adsorption of riboflavin on the surface of nanoparticles due to dissolution of the silver layer of the nanoparticles. It was found that the adsorption isotherm is best fitted to Dubinin-Radushkevich and Freundlich models and kinetic model followed a pseudo-second-order adsorption rate.

  5. Growth process optimization of ZnO thin film using atomic layer deposition

    Science.gov (United States)

    Weng, Binbin; Wang, Jingyu; Larson, Preston; Liu, Yingtao

    2016-12-01

    The work reports experimental studies of ZnO thin films grown on Si(100) wafers using a customized thermal atomic layer deposition. The impact of growth parameters including H2O/DiethylZinc (DEZn) dose ratio, background pressure, and temperature are investigated. The imaging results of scanning electron microscopy and atomic force microscopy reveal that the dose ratio is critical to the surface morphology. To achieve high uniformity, the H2O dose amount needs to be at least twice that of DEZn per each cycle. If the background pressure drops below 400 mTorr, a large amount of nanoflower-like ZnO grains would emerge and increase surface roughness significantly. In addition, the growth temperature range between 200 °C and 250 °C is found to be the optimal growth window. And the crystal structures and orientations are also strongly correlated to the temperature as proved by electron back-scattering diffraction and x-ray diffraction results.

  6. Mimicry of sputtered i-ZnO thin films using chemical bath deposition for solution-processed solar cells.

    Science.gov (United States)

    Della Gaspera, Enrico; van Embden, Joel; Chesman, Anthony S R; Duffy, Noel W; Jasieniak, Jacek J

    2014-12-24

    Solution processing provides a versatile and inexpensive means to prepare functional materials with specifically designed properties. The current challenge is to mimic the structural, optical, and/or chemical properties of thin films fabricated by vacuum-based techniques using solution-based approaches. In this work we focus on ZnO to show that thin films grown using a simple, aqueous-based, chemical bath deposition (CBD) method can mimic the properties of sputtered coatings, provided that the kinetic and thermodynamic reaction parameters are carefully tuned. The role of these parameters toward growing highly oriented and dense ZnO thin films is fully elucidated through detailed microscopic and spectroscopic investigations. The prepared samples exhibit bulk-like optical properties, are intrinsic in their electronic characteristics, and possess negligible organic contaminants, especially when compared to ZnO layers deposited by sol-gel or from nanocrystal inks. The efficacy of our CBD-grown ZnO thin films is demonstrated through the effective replacement of sputtered ZnO buffer layers within high efficiency solution processed Cu2ZnSnS4xSe4(1-x) solar cells.

  7. Low temperature deposition of ZnO semiconductor thin films on a PEN substrate by a solution process

    Science.gov (United States)

    Tsay, Chien-Yie; Wu, Pei-Wen

    2013-07-01

    Low-temperature processed ZnO semiconductor films were deposited onto polyethylene naphthalate (PEN) plastic substrates by a spin coating technique using ZnO nanoparticle (NP) dispersion. The ZnO nanoparticles (NPs) were synthesized by the hydrothermal method, and solution processable dispersion was used to disperse the ZnO NPs in a mixed aqueous solution with a polyvinylpyrrolidone (PVP) dispersant agent. The effects of annealing temperature (from 150°C to 250°C) on the electrical properties of glass/ZnO film samples are reported. The optimized annealing condition (200°C) was applied for ZnO film deposited on a PEN substrate. Comparative electrical properties of the PEN/ZnO film samples before and after bending tests are also presented. Experimental results show that the electrical resistivity of the PEN/ZnO film sample was 1.91 × 104 Ω cm with a Hall mobility of 45.9 cm2/Vs. After bending tests, the electrical resistivity was raised to 1.26 × 105 Ω cm and the Hall mobility was reduced to 31.0 cm2/Vs.

  8. Ion energy effects on the intrinsic stress in B sub x N sub y layers deposited by ion-beam-assisted evaporation

    Energy Technology Data Exchange (ETDEWEB)

    Stambouli, V.; Burat, O.; Bouchier, D.; Gautherin, G. (Inst. d' Electronique Fondamentale, Univ. Paris-Sud, 91 - Orsay (France))

    1990-12-05

    The intrinsic stress {sigma} of boron nitride (B{sub x}N{sub y}) films deposited at room temperature by ion-beam-assisted deposition has been investigated as a function of the atomic flux ratio and film composition for different N{sub 2}{sup +} energy values ranging from 0.25 to 2 keV. The value of {sigma} was evaluated by an interferometric Newton's rings method. The stress reverses and becomes compressive for an atomic flux ratio N:B less than 0.3 which is the lowest value we have examined. Two domains of composition can be emphasized following the stress behaviour as a function of the ion energy. The first domain is that of nitrogen-poor films where the absolute value of the stress decreases (from -2.4 to -0.45 GPa) when the energy is increased. The creation of vacancies in the deposit depth or an ''ion annealing'' effect is proposed to explain the corresponding stress behaviour which is correlated with density measurements. The second domain is that of nitrogen-rich films in which the compressive stress increases drastically to -4.8 GPa with the ion energy. In this domain, according to the ion peening model proposed by Windischmann, the stress varies in proportion to the nuclear stopping power of the deposited material. (orig.).

  9. Example process hazard analysis of a Department of Energy water chlorination process

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    On February 24, 1992, the Occupational Safety and Health Administration (OSHA) released a revised version of Section 29 Code of Federal Regulations CFR Part 1910 that added Section 1910.119, entitled ``Process Safety Management of Highly Hazardous Chemicals`` (the PSM Rule). Because US Department of Energy (DOE) Orders 5480.4 and 5483.1A prescribe OSHA 29 CFR 1910 as a standard in DOE, the PSM Rule is mandatory in the DOE complex. A major element in the PSM Rule is the process hazard analysis (PrHA), which is required for all chemical processes covered by the PSM Rule. The PrHA element of the PSM Rule requires the selection and application of appropriate hazard analysis methods to systematically identify hazards and potential accident scenarios associated with processes involving highly hazardous chemicals (HHCs). The analysis in this report is an example PrHA performed to meet the requirements of the PSM Rule. The PrHA method used in this example is the hazard and operability (HAZOP) study, and the process studied is the new Hanford 300-Area Water Treatment Facility chlorination process, which is currently in the design stage. The HAZOP study was conducted on May 18--21, 1993, by a team from the Westinghouse Hanford Company (WHC), Battelle-Columbus, the DOE, and Pacific Northwest Laboratory (PNL). The chlorination process was chosen as the example process because it is common to many DOE sites, and because quantities of chlorine at those sites generally exceed the OSHA threshold quantities (TQs).

  10. Sustainable chemical processing and energy-carbon dioxide management: review of challenges and opportunities

    DEFF Research Database (Denmark)

    Frauzem, Rebecca; Vooradi, Ramsagar; Bertran, Maria-Ona

    2017-01-01

    of sustainable chemical processing in the utilization of biomass-based energy-chemicals production, carbon-capture and utilization with zero or negative CO2-emission to produce value added chemicals as well as retrofit design of energy intensive chemical processes with significant reduction of energy consumption...... are presented. These examples highlight issues of energy sustainable design, energy-CO2 neutral design, energy-retrofit design,and energy-process intensification. Finally, some perspectives on the status and future directions of carbon dioxide management are given....

  11. Process-based, morphodynamic hindcast of decadal deposition patterns in San Pablo Bay, California, 1856-1887

    Science.gov (United States)

    van der Wegen, M.; Jaffe, B.E.; Roelvink, J.A.

    2011-01-01

    This study investigates the possibility of hindcasting-observed decadal-scale morphologic change in San Pablo Bay, a subembayment of the San Francisco Estuary, California, USA, by means of a 3-D numerical model (Delft3D). The hindcast period, 1856-1887, is characterized by upstream hydraulic mining that resulted in a high sediment input to the estuary. The model includes wind waves, salt water and fresh water interactions, and graded sediment transport, among others. Simplified initial conditions and hydrodynamic forcing were necessary because detailed historic descriptions were lacking. Model results show significant skill. The river discharge and sediment concentration have a strong positive influence on deposition volumes. Waves decrease deposition rates and have, together with tidal movement, the greatest effect on sediment distribution within San Pablo Bay. The applied process-based (or reductionist) modeling approach is valuable once reasonable values for model parameters and hydrodynamic forcing are obtained. Sensitivity analysis reveals the dominant forcing of the system and suggests that the model planform plays a dominant role in the morphodynamic development. A detailed physical explanation of the model outcomes is difficult because of the high nonlinearity of the processes. Process formulation refinement, a more detailed description of the forcing, or further model parameter variations may lead to an enhanced model performance, albeit to a limited extent. The approach potentially provides a sound basis for prediction of future developments. Parallel use of highly schematized box models and a process-based approach as described in the present work is probably the most valuable method to assess decadal morphodynamic development. Copyright ?? 2011 by the American Geophysical Union.

  12. Atmospheric deposition process for enhanced hybrid organic-inorganic multilayer barrier thin films for surface protection

    Science.gov (United States)

    Rehman, Mohammad Mutee ur; Kim, Kwang Tae; Na, Kyoung Hoan; Choi, Kyung Hyun

    2017-11-01

    In this study, organic polymer poly-vinyl acetate (PVA) and inorganic aluminum oxide (Al2O3) have been used together to fabricate a hybrid barrier thin film for the protection of PET substrate. The organic thin films of PVA were developed through roll to roll electrohydrodynamic atomization (R2R-EHDA) whereas the inorganic thin films of Al2O3 were grown by roll to roll spatial atmospheric atomic layer deposition (R2R-SAALD) for mass production. The use of these two technologies together to develop a multilayer hybrid organic-inorganic barrier thin films under atmospheric conditions is reported for the first time. These multilayer hybrid barrier thin films are fabricated on flexible PET substrate. Each layer of Al2O3 and PVA in barrier thin film exhibited excellent morphological, chemical and optical properties. Extremely uniform and atomically thin films of Al2O3 with average arithmetic roughness (Ra) of 1.64 nm and 1.94 nm respectively concealed the non-uniformity and irregularities in PVA thin films with Ra of 2.9 nm and 3.6 nm respectively. The optical transmittance of each layer was ∼ 80-90% while the water vapor transmission rate (WVTR) of hybrid barrier was in the range of ∼ 2.3 × 10-2 g m-2 day-1 with a total film thickness of ∼ 200 nm. Development of such hybrid barrier thin films with mass production and low cost will allow various flexible electronic devices to operate in atmospheric conditions without degradation of their properties.

  13. A PROCESS FOR DEPOSITING METAL CONTACTS ON A BURIED GRID SOLAR CELL AND A SOLAR CELL OBTAINED BY THE PROCESS

    DEFF Research Database (Denmark)

    2002-01-01

    A buried grid solar cell is manufactured by a process for metallising one or more metal contacts of a buried grid solar cell having a body of doped semiconductor material, wherein the electrical contact(s) is/are provided by conducting material being arranged in a pattern of one or more grooves...... conducting contact forming material by electrolytic plating using a conventional electrolytic bath further comprising a levelling additive and a suppressing additive and using substantially constant cell voltage....

  14. Deposit model for volcanogenic uranium deposits

    Science.gov (United States)

    Breit, George N.; Hall, Susan M.

    2011-01-01

    Volcanism is a major contributor to the formation of important uranium deposits both close to centers of eruption and more distal as a result of deposition of ash with leachable uranium. Hydrothermal fluids that are driven by magmatic heat proximal to some volcanic centers directly form some deposits. These fluids leach uranium from U-bearing silicic volcanic rocks and concentrate it at sites of deposition within veins, stockworks, breccias, volcaniclastic rocks, and lacustrine caldera sediments. The volcanogenic uranium deposit model presented here summarizes attributes of those deposits and follows the focus of the International Atomic Energy Agency caldera-hosted uranium deposit model. Although inferred by some to have a volcanic component to their origin, iron oxide-copper-gold deposits with economically recoverable uranium contents are not considered in this model.

  15. Lightning-driven inner radiation belt energy deposition into the atmosphere: implications for ionisation-levels and neutral chemistry

    Directory of Open Access Journals (Sweden)

    C. J. Rodger

    2007-08-01

    Full Text Available Lightning-generated whistlers lead to coupling between the troposphere, the Van Allen radiation belts and the lower-ionosphere through Whistler-induced electron precipitation (WEP. Lightning produced whistlers interact with cyclotron resonant radiation belt electrons, leading to pitch-angle scattering into the bounce loss cone and precipitation into the atmosphere. Here we consider the relative significance of WEP to the lower ionosphere and atmosphere by contrasting WEP produced ionisation rate changes with those from Galactic Cosmic Radiation (GCR and solar photoionisation. During the day, WEP is never a significant source of ionisation in the lower ionosphere for any location or altitude. At nighttime, GCR is more significant than WEP at altitudes <68 km for all locations, above which WEP starts to dominate in North America and Central Europe. Between 75 and 80 km altitude WEP becomes more significant than GCR for the majority of spatial locations at which WEP deposits energy. The size of the regions in which WEP is the most important nighttime ionisation source peaks at ~80 km, depending on the relative contributions of WEP and nighttime solar Lyman-α. We also used the Sodankylä Ion Chemistry (SIC model to consider the atmospheric consequences of WEP, focusing on a case-study period. Previous studies have also shown that energetic particle precipitation can lead to large-scale changes in the chemical makeup of the neutral atmosphere by enhancing minor chemical species that play a key role in the ozone balance of the middle atmosphere. However, SIC modelling indicates that the neutral atmospheric changes driven by WEP are insignificant due to the short timescale of the WEP bursts. Overall we find that WEP is a significant energy input into some parts of the lower ionosphere, depending on the latitude/longitude and altitude, but does not play a significant role in the neutral chemistry of the mesosphere.

  16. Investigation on primary and secondary processes in Nasirabad manganese deposit, south of Neyriz: using mineralogy and Pb isotope geochemistry

    Directory of Open Access Journals (Sweden)

    Ali Reza Zarasvandi

    2013-04-01

    Full Text Available The Nasirabad manganese deposit is located 5 km south of Nasirabad, 8 km SW of Neyriz in the Fars province. Structurally, the area is placed in the southeastern part of Zagros thrust belt. In this area, the manganese mineralization occurred as ore layers and nodules, interlayered with Pichakun radiolarite chert deposits. In this study, mineralogy and geochemistry of uranium, thorium and lead isotopes were used to investigate the primary and secondary processes. In this way, in addition to petrographic and XRD studies, ICP-MS analysis was carried out in order to measure the U, Th and Pb isotopes. The strong fractionation of Fe and Mn phases and also the absence of Fe-bearing minerals in the XRD results, presence of syngenetic todorokite and quartz crystals, high U/Th ratios in some samples and Th versus U diagrams, all indicate entrance of Mn-bearing hydrothermal fluids into the sedimentary basin of the Nasirabad manganese deposit. The pyrolusites in radiolarites tests as replacement textures, host rock space filling and fracture filling pyrolusites, indicates the influence of secondary exogenic processes on primary hydrothermal mineralization. Non-homogenous 206Pb/Pb204, 207Pb/Pb204 and 208Pb/Pb204 values show non-steady hydrothermal processes in the sedimentary basin and indicate mixing of hydrothermal lead isotopes with another secondary source. Strong positive correlation between absolute values of radiogenic lead isotopes and insoluble High Field Strength Elements (HFSE such as 207Pb vs Nb (r=0.81, 207Pb vs TiO2 (r=0.93, 207Pb vs Th (r=0.79 and strong correlation between these elements and some mafic components like 208Pb vs Fe2O3 (r=0.94 and Th vs MgO (r=0.86 represent entrance of radiogenic lead with mafic detrital materials into the sedimentary basin. Similar linear trend among 206Pb/Pb204 vs 208Pb/Pb204 and 207Pb/Pb204 ratios in nodules and manganese layers show the same geochemical condition in Mn-nodules and layers formation and

  17. Energy Demand Modeling Methodology of Key State Transitions of Turning Processes

    Directory of Open Access Journals (Sweden)

    Shun Jia

    2017-04-01

    Full Text Available Energy demand modeling of machining processes is the foundation of energy optimization. Energy demand of machining state transition is integral to the energy requirements of the machining process. However, research focus on energy modeling of state transition is scarce. To fill this gap, an energy demand modeling methodology of key state transitions of the turning process is proposed. The establishment of an energy demand model of state transition could improve the accuracy of the energy model of the machining process, which also provides an accurate model and reliable data for energy optimization of the machining process. Finally, case studies were conducted on a CK6153i CNC lathe, the results demonstrating that predictive accuracy with the proposed method is generally above 90% for the state transition cases.

  18. Energy Deposition and DPA in the Superconducting Links for the HILUMI LHC Project at the LHC Interaction Points

    CERN Document Server

    AUTHOR|(CDS)2092158; Broggi, Francesco; Santini, C; Ballarino, Amalia; Cerutti, Francesco; Esposito, Luigi Salvatore

    2015-01-01

    In the framework of the upgrade of the LHC machine, the powering of the LHC magnets foresees the removal of the power converters and distribution feedboxes from the tunnel and its location at the surface[1]. The Magnesium Diboride (MgB2) connecting lines in the tunnel will be exposed to the debris from 7+7 TeV p-p interaction. The Superconducting (SC) Links will arrive from the surface to the tunnel near the separation dipole, at about 80 m from the Interaction Point at IP1 and IP5. The Connection Box (where the cables of the SC Links are connected to the NbTi bus bar) will be close to the beam pipe. The debris and its effect on the MgB2 SC links in the connection box (energy deposition and displacement per atom) are presented. The effect of thermal neutrons on the Boron consumption and the contribution of the lithium nucleus and the alpha particle on the DPA are evaluated. The results are normalized to an integrated luminosity of 3000 fb-1, value that represents the LHC High Luminosity lifetime. The dose de...

  19. Value of Dual Energy Computed Tomography for detection of myocardial iron deposition in Thalassaemia patients: Initial experience

    Energy Technology Data Exchange (ETDEWEB)

    Hazirolan, Tuncay; Akpinar, Burcu [Hacettepe University Medical School, Department of Radiology, Ankara (Turkey); Unal, Sule; Guemruek, Fatma [Hacettepe University Medical School, Department of Pediatrics, Ankara (Turkey); Haliloglu, Mithat [Hacettepe University Medical School, Department of Radiology, Ankara (Turkey); Alibek, Sedat [Hacettepe University Medical School, Department of Radiology, Ankara (Turkey); Radiology Institute, University of Erlangen/Nurnberg, 91054 Erlangen (Germany)], E-mail: sedat.alibek@uk-erlangen.de

    2008-12-15

    Purpose: The aim of our study was to compare the value of cardiac DECT (cDECT) for detection of myocardial iron deposition to T2*w cardiac MRI (cMRI). Material and methods: Nineteen patients with clinical history of Thalassaemia underwent T2*-weighted cardiac MRI (cMRI) with a 1.5 T MR scanner (MAGNETOM Symphony, Siemens Medical Solutions, Erlangen, Germany) and cardiac dual energy CT (cDECT) with a DSCT scanner (SOMATOM Definition, Siemens Medical Solutions, Erlangen, Germany) on the same day. HU values obtained from cDECT scans and T2*-values from cMRI were statistically correlated to calculate significance levels. Table times were measured for both cDECT and cMRI and compared. Patients were asked to grade their subjective comfort during the examination. Results: In all patients cDECT scans were successfully acquired. HU values of septal muscle correlated strongly with T2*-values, whereas no correlation was found for paraspinal muscle. Table time was significantly shorter for cDECT compared to cMRI (mean: 3.7 min vs. 11.2 min) and subjective patient comfort was rated comfortable for cDECT and average to poor for cMRI. Mean radiation dose was 0.71 mSv. Conclusion: cDECT scans seem to be possible for evaluation of myocardial iron load in pediatric Thalassaemia patients.

  20. The distribution of urate deposition within the extremities in gout: a review of 148 dual-energy CT cases

    Energy Technology Data Exchange (ETDEWEB)

    Mallinson, Paul I. [Vancouver General Hospital, Radiology Department, Vancouver (Canada); Vancouver General Hospital, Clinical Fellow in Musculoskeletal Radiology, Vancouver, BC (Canada); Reagan, Adrian C.; Munk, Peter L.; Ouellette, Hugue; Nicolaou, Savvas [Vancouver General Hospital, Radiology Department, Vancouver (Canada); Coupal, Tyler [McMaster University, De Groote School of Medicine, Hamilton, Ontario (Canada)

    2014-03-15

    Clinical detection of gout can be difficult due to co-existent and mimicking arthropathies and asymptomatic disease. Understanding of the distribution of urate within the body can aid clinical diagnosis and further understanding of the resulting pathology. Our aim was to determine this distribution of urate within the extremities in patients with gout. All patients who underwent a four-limb dual-energy computed tomography (DECT) scan for suspected gout over a 2-year period were identified (n = 148, 121 male, 27 female, age range, 16-92 years, mean = 61.3 years, median = 63 years). The reports of the positive cases were retrospectively analyzed and the locations of all urate deposition recorded and classified by anatomical location. A total of 241 cases met the inclusion criteria, of which 148 cases were positive. Of these, 101 (68.2 %) patients had gout in the foot, 81 (56.1 %) in the knee, 79 (53.4 %) in the ankle, 41 (27.7 %) in the elbow, 25 (16.9 %) in the hand, and 25 (16.9 %) in the wrist. The distribution was further subcategorized for each body part into specific bone and soft tissue structures. In this observational study, we provide for the first time a detailed analysis of extremity urate distribution in gout, which both supports and augments to the current understanding based on clinical and microscopic findings. (orig.)

  1. "Plasma charging damage induced by a power ramp down step in the end of plasma enhanced chemical vapour deposition (PECVD) process

    NARCIS (Netherlands)

    Wang, Zhichun; Ackaert, Jan; Salm, Cora; Kuper, F.G.; Bessemans, Klara; de Backer, Eddy

    2003-01-01

    Plasma Enhanced Chemical Vapour Deposition (PECVD) is one of the main plasma processes which induce charging damage to gate oxides during the VLSI processes. All the previous studies, however, describe the charging phenomena only at the beginning of PECVD process, when a very thin oxide layer covers

  2. Energy Efficiency Improvement and Cost Saving Opportunities for the Dairy Processing Industry: An ENERGY STAR? Guide for Energy and Plant Managers

    Energy Technology Data Exchange (ETDEWEB)

    Brush, Adrian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Masanet, Eric [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Worrell, Ernst [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2011-10-01

    The U.S. dairy processing industry—defined in this Energy Guide as facilities engaged in the conversion of raw milk to consumable dairy products—consumes around $1.5 billion worth of purchased fuels and electricity per year. Energy efficiency improvement is an important way to reduce these costs and to increase predictable earnings, especially in times of high energy price volatility. There are a variety of opportunities available at individual plants in the U.S. dairy processing industry to reduce energy consumption and greenhouse gas emissions in a cost-effective manner. This Energy Guide discusses energy efficiency practices and energy-efficient technologies that can be implemented at the component, process, facility, and organizational levels. A discussion of the trends, structure, and energy consumption characteristics of the U.S. dairy processing industry is provided along with a description of the major process technologies used within the industry. Next, a wide variety of energy efficiency measures applicable to dairy processing plants are described. Many measure descriptions include expected savings in energy and energy-related costs, based on case study data from real-world applications in dairy processing facilities and related industries worldwide. Typical measure payback periods and references to further information in the technical literature are also provided, when available. Given the importance of water in dairy processing, a summary of basic, proven measures for improving water efficiency are also provided. The information in this Energy Guide is intended to help energy and plant managers in the U.S. dairy processing industry reduce energy and water consumption in a cost-effective manner while maintaining the quality of products manufactured. Further research on the economics of all measures—as well as on their applicability to different production practices—is needed to assess their cost effectiveness at individual plants.

  3. Energy Efficiency Improvement and Cost Saving Opportunities for the Fruit and Vegetable Processing Industry. An ENERGY STAR Guide for Energy and Plant Managers

    Energy Technology Data Exchange (ETDEWEB)

    Masanet, Eric; Masanet, Eric; Worrell, Ernst; Graus, Wina; Galitsky, Christina

    2008-01-01

    The U.S. fruit and vegetable processing industry--defined in this Energy Guide as facilities engaged in the canning, freezing, and drying or dehydrating of fruits and vegetables--consumes over $800 million worth of purchased fuels and electricity per year. Energy efficiency improvem