WorldWideScience

Sample records for energi reaktor temperatur

  1. ANALISIS INVENTORI REAKTOR DAYA EKSPERIMENTAL JENIS REAKTOR GAS TEMPERATUR TINGGI

    Directory of Open Access Journals (Sweden)

    Sri Kuntjoro

    2016-06-01

    kelompok Cs sebesar 2,20E+16 Bq, 2,40E+16 Bq dan 2,60E+16 Bq. Inventori teras selanjutnya akan digunakan untuk menghitung suku sumber dari reaktor yang akan digunakan sebagai dasar untuk perhitungan sebaran radionuklida ke lingkungan. Kata kunci: Inventori, RDE, daya 10 MWt, daya 20 MWt, daya 30 MWt. ABSTRACT THE ANALYSIS FOR INVENTORY OF EXPERIMENTAL REACTOR HIGH TEMPERATURE GAS REACTOR TYPE. Relating to the plan of the National Nuclear Energy Agency (BATAN to operate an experimental reactor of High Temperature Gas Reactors type (RGTT, it is necessary to reactor safety analysis, especially with regard to environmental issues. Analysis of the distribution of radionuclides from the reactor into the environment in normal or abnormal operating conditions starting with the estimated reactor inventory based on the type, power, and operation of the reactor. The purpose of research is to analyze inventory terrace for Experimental Power Reactor design (RDE high temperature gas reactor type power 10 MWt, 20 MWt and 30 MWt. Analyses were performed using ORIGEN2 computer code with high temperatures cross-section library. Calculation begins with making modifications to some parameter of cross-section library based on the core average temperature of 570 °C and continued with calculations of reactor inventory due to RDE 10 MWt reactor power. The main parameters of the reactor 10 MWt RDE used in the calculation of the main parameters of the reactor similar to the HTR-10 reactor. After the reactor inventory 10 MWt RDE obtained, a comparison with the results of previous researchers. Based upon the suitability of the results, it make the design for the reactor RDE 20MWEt and 30 MWt to obtain the main parameters of the reactor in the form of the amount of fuel in the pebble bed reactor core, height and diameter of the terrace. Based on the main parameter or reactor obtained perform of calculation to get reactor inventory for RDE 20 MWT and 30 MWT with the same methods as the

  2. Studi Fleksibilitas dan Posibilitas Daur Bahan Bakar Reaktor Temperatur Tinggi (HTR

    Directory of Open Access Journals (Sweden)

    Hery Adrial

    2017-03-01

    Full Text Available Dewasa ini sejumlah institusi riset di dunia sedang mengembangkan teknologi reaktor temperatur tinggi (HTR melalui berbagai program seperti PUMA, RAPHAEL, ANTARES, dll. Tujuan dari program ini adalah untuk mengembangkan HTR versi demontrasi dan komersial. HTR merupakan reaktor berpendingin gas temperatur tinggi, bermoderator grafit dengan spektrum neutron termal dan temperatur outlet teras hingga 1.000oC. Fasilitas energi ini dapat mencapai efisiensi termodinamika yang cukup tinggi (~80% dengan kapabilitas generasi listrik dan produksi hidrogen. Makalah ini membahas fleksibilitas dan posibilitas daur bahan bakar HTR yang meliputi serangkaian daur bahan bakar komprehensif. Dikategorikan ke dalam 4 kelompok, yaitu daur bahan bakar uranium pengkayaan rendah (LEU, daur bahan bakar MOX, daur bahan bakar hanya plutonium dan daur bahan bakar berbasis thorium, daur bahan bakar HTR dievaluasi secara sistematis. Makalah ini juga mendiskusikan pertimbangan pemilihan daur bahan bakar untuk sejumlah HTR yang telah dioperasikan seperti AVR dan THTR Jerman, Peach Bottom dan Fort Saint Vrain USA, DRAGON Inggris, dll., dan yang sedang dalam proses desain seperti HTR AREVA Perancis, PBMR Afrika Selatan, dll. Hasil diskusi menyimpulkan bahwa daur LEU layak dipilih sebagai daur referensi untuk proyek HTR masa kini dan masa yang akan datang.

  3. Modifikasi Panel Monitor Reaktor Triga 2000

    OpenAIRE

    P, Margono; M, Pardi; M, Muhaimin

    2003-01-01

    MODIFIKASI PANEL MONITOR REAKTOR TRIGA 2000. Sebagai bagian dan modifikasi sistem kendali reaktor TRIGA 2000 telah dibuat sistem pengamatan parameter-parameter yang diperlukan dalam operasi reaktor seperti daya reaktor, temperatur air, temperatur bahan bakar dan lain sebagainya. Pengamatan tersebut diambil dan sistem pengukuran yang sudah ada dan ditampilkan dalam bentuk digital panel meter. Pengukuran diambil dalam berbagai mode luaran sebagai arus dan tegangan. Sistem pengamatan ini merupak...

  4. OPTIMASI GEOMETRI TERAS REAKTOR DAN KOMPOSISI BAHAN BAKAR BERBENTUK BOLA PADA DESAIN HIGH TEMPERATURE FAST REACTOR (HTFR

    Directory of Open Access Journals (Sweden)

    Agustina Mega

    2015-04-01

    Full Text Available Telah dilakukan desain High Temperature Fast Reactor (HTFR tipe pebble dengan bahan bakar uranium plutonium nitrida berpendingin Pb-Bi. Parameter yang dianalisis adalah kritikalitas teras, koefisien reaktivitas temperatur bahan bakar, koefisien reaktivitas void pendingin dan kemampuan breeding reaktor. Perhitungan dilakukan dengan paket program SRAC2K3. Dari penelitian ini diharapkan diperoleh desain teras berumur lama dan memiliki fitur keselamatan melekat. Dari penelitian ini diperoleh desain reaktor dengan diameter 520 cm dan tinggi 480 cm. Bahan bakar berbentuk pebble dengan 63 % UN-37 % PuN pada zona core dan 95,5 % UN-4,5 % PuN pada zona blanket. Reaktor tidak kritis setelah kurang lebih 800 hari dan keff pada BoL 1,078223 dan keff setelah 800 hari adalah 0,986379. Dari penelitian ini diperoleh koefisien reaktivitas temperatur bahan bakar sebesar -2,190014E-05 pada saat BoL dan -1,390773E-05 setelah 800 hari serta koefisien reaktivitas void pendingin sebesar -2,160402E-04/% void pada saat BoL dan setelah 800 hari sebesar -2,942364E-03/% void. Reaktor merupakan jenis fast breeder ditandai dengan naiknya densitas plutonium 239. Kata kunci : desain, teras, HTFR, keselamatan, umur, koefisien reaktivitas.   Design of pebble bed type High Temperature Fast Reactor (HTFR with uranium plutonium nitride fuel and Pb-Bi cooled has been done. The parameters being analyzed were core criticality, fuel temperature coefficient, void coefficient and reactor breeding ability. Calculation was done by using SRAC2K3 computer code. This research is expected to obtaine the design with long life core and inherent safety features. This research obtained core design with a diameter of 520 cm and 480 cm core high. Shaped pebble fuel bed with the 63 % UN-37 % PUN on core zone and 95.5 % UN-4.5 % Pu on blanket zone and keff value is 1.078223 with approximately 800 day of core life. The fuel temperature coefficient is -2.190014E-05 at BOL and is 1.390773E-05 at EOL and

  5. ANALISIS KECELAKAAN REAKTOR AKIBAT KEGAGALAN SISTEM PEMBUANG PANAS PADA REAKTOR NUKLIR GENERASI IV

    Directory of Open Access Journals (Sweden)

    A. G. Abdullah

    2012-01-01

    Full Text Available Salah satu aspek terpenting dalam proses desain reaktor nuklir adalah aspek keselamatan reaktor. Sebelum membangun reaktor secara fisik, terlebih dahulu dibuat perencaaan perhitungan yang matang termasuk melakukan simulasi kinerja keselamatannya dalam menghadapi kemungkinan kecelakaan. Penelitian ini bertujuan untuk mengembangkan model simulasi kecelakaan Pembangkit Listrik Tenaga Nuklir (PLTN yang disebabkan  gagalnya sistem pembuang panas. Kecelakaan akibat gagalnya sistem pembuang panas dipicu oleh hilangnya kemampuan pendinginan dari pembangkit uap. Urutan kecelakaan ini diawali dengan hilangnya kemampuan reaktor untuk membuang panas dari loop pendingin sekunder. Selama kecelakaan, laju pembuangan panas mengalami penurunan sedangkan temperatur masukan pendingin mengalami peningkatan. Hasil simulasi memberikan gambaran bahwa reaktor dapat bertahan dari kecelakaan. Hasil analisis kecelakaan menunjukkan bahwa temperatur maksimum bahan bakar, selongsong dan pendingin memiliki batas keselamatan yang sangat besar.One of the most important aspects in nuclear reactor design process is the safety aspect. Advanced and accurate safety simulation must be performed before it can be built.  This research aims to develop a simulation model of Nuclear Power Plant (NPP accidents due to the loss of  heat sink system. Loss of heat sink accident was triggered by the loss of cooling capability of steam generators.  This  accident  sequence  began with the loss of the reactor’s ability to remove heat from the secondary cooling loop. During the accident, the heat dissipation rate decreased whereas the coolant inlet temperatures increased till a new equilibrium level. The analysis results of the accident showed that there are large safety margin to the maximum temperature of the fuel, cladding, and coolant.

  6. Desain Pengembangan Model Alat Uji Reaktor Nuklir Tipe Small Modular Reactor (Smr) Menggunakan Nanofluida Sebagai Fluida Pendingin

    OpenAIRE

    Dermawan, Erwin; Rasma, Rasma; Diniardi, Ery; Ramadhan, Anwar Ilmar

    2014-01-01

    Perkembangan dan penggunaan energi nuklir saat ini berkembang sangat pesat, untuk mencapaiteknologi yang semakin maju, baik dari segi desain, faktor ekonomi dan juga faktorkeselamatannya. Dari aspek termofluida reaktor nuklir harus dilakukan dengan perhitungan dankondisi yang mendekati sempurna. Termasuk saat ini mulai dikembangkannya reaktor nuklirdengan daya rendah dibawah 300 MW, atau biasa disebut dengan Small Modular Reactor (SMR).Salah satuny...

  7. INVESTIGASI KARAKTERISTIK TERMOHIDROLIKA TERAS REAKTOR DAYA KECIL DENGAN PENDINGINAN SIRKULASI ALAM MENGGUNAKAN RELAP5

    Directory of Open Access Journals (Sweden)

    Susyadi Susyadi

    2016-02-01

    Full Text Available ABSTRAK INVESTIGASI KARAKTERISTIK TERMOHIDROLIKA TERAS REAKTOR DAYA KECIL DENGAN PENDINGINAN SIRKULASI ALAM MENGGUNAKAN RELAP5. Reaktor modular daya-kecil (small modular reactor, SMR memiliki prospek tinggi untuk dibangun di Indonesia. Keluaran dayanya yang relatif kecil dan disainnya yang kompak serta dapat dikonstruksi secara modular memberikan keunggulan fleksibilitas pembangunan yang lebih baik dibanding reaktor konvensional berdaya besar. Disain sistem reaktor kategori ini sangat bervariasi, salah satu diantaranya adalah jenis reaktor air tekan (pressurized water reactor, PWR yang menerapkan sirkulasi alamiah pada sistem pendingin primernya. Selain itu reaktor ini juga memiliki teras (core lebih pendek dibanding PWR konvensional. Dari kedua perbedaan tersebut maka terdapat kemungkinan perbedaan pola perpindahan panas yang dapat berimplikasi terhadap keselamatan secara keseluruhan. Oleh karena itu, pada penelitian ini dilakukan investigasi terhadap karakteristik termohidrolika teras reaktor tersebut khususnya karakteristik temperatur fluida dan bahan bakar serta laju alir fluidanya. Tujuannya adalah untuk mengetahui perbedaan marjin keselamatan temperatur teras reaktor bila dibanding dengan PWR konvensional. Investigasi dilakukan dengan menggunakan program RELAP5, dimana secara parsial teras reaktor dimodelkan menggunakan model-model generik yang ada pada program dan dilakukan beberapa perhitungan kondisi tunak. Hasil perhitungan menunjukkan bahwa saat beroperasi pada daya nominalnya, reaktor modular ini memiliki margin temperatur pendidihan sebesar 2K lebih baik dibanding reaktor konvensional. Selain itu, keunggulan marjin keselamatan reaktor modular daya-kecil ini juga ditunjukkan dari naiknya laju alir mengikuti kenaikan dayanya yang berarti memiliki sifat keselamatan yang melekat (inherent safety. Kata kunci: reaktor modular daya-kecil, PWR, sirkulasi alam, RELAP5, termohidrolika   ABSTRACT INVESTIGATION ON CORE THERMAL HYDRAULIC

  8. PEROLEHAN SUHU AIR PENDINGIN PRIMER REAKTOR TRIGA 2000 KETIKA PENAMBAHAN CEROBONG DAN PELAT PENUKAR PANAS

    Directory of Open Access Journals (Sweden)

    Reinaldy Nazar

    2015-03-01

    Full Text Available Kesinambungan operasi reaktor TRIGA 2000 di antaranya ditentukan oleh suhu bahan bakar dan suhu air pendingin primer. Sebagai contoh pengoperasian reaktor TRIGA 2000 saat ini sulit mencapai daya 2000 kW, karena suhu di pusat elemen bahan bakar di dalam teras reaktor mencapai 675 oC, suhu pendingin primer yang masuk ke teras reaktor mencapai 41,3 oC, suhu pendingin primer yang ke luar dari tangki reaktor mencapai 48,2 oC. Tingginya suhu elemen bahan bakar dan suhu pendingin primer di dalam teras telah meningkatkan pendidihan dan menambah pembentukan gelembung uap di dalam teras reaktor, sehingga menurunkan moderasi neutron oleh pendingin primer di dalam teras dan reaktor tidak mampu mencapai daya 2000 KW. Beberapa kegiatan yang dapat dilakukan untuk menurunkan suhu bahan bakar dan air pendingin primer di dalam teras reaktor TRIGA 2000, di antaranya dengan menempatkan cerobong di atas teras reaktor dan menambah pelat penukar panas. Mengingat studi kasus ini tidak memungkinkan untuk dilakukan secara eksperimen, maka analisis dilakukan melalui kajian teoritik menggunakan program komputer CFD. Berdasarkan hasil kajian yang telah dilakukan diketahui bahwa dengan menambah tinggi cerobong menjadi 2 m, pelat penukar panas menjadi 384 lembar, laju alir pendingin primer 950 gpm, dan laju alir pendingin sekunder menjadi 1200 gpm, mampu menurunkan suhu pendingin primer yang ke luar dari penukar panas atau suhu pendingin primer yang masuk ke teras reaktor menjadi 30,48 oC. Jika kondisi ini digunakan tentunya akan menurunkan suhu maksimum kelongsong bahan bakar, dan suhu pendingin primer di dalam teras, sehingga akan mengurangi pendidihan di dalam teras reaktor, meskipun hal ini akan menaikkan konsentrasi N-16 di permukaan tangki reaktor menjadi 49,41%. Kata kunci: cerobong, pelat penukar panas, suhu bahan bakar, suhu pendingin primer.   Continuation of the TRIGA 2000 reactor operation is determined by the fuel and primary cooling water temperature. For

  9. ANALISIS DESAIN PROSES SISTEM PENDINGIN PADA REAKTOR RISET INOVATIF 50 MW

    Directory of Open Access Journals (Sweden)

    Sukmanto Dibyo

    2015-03-01

    Full Text Available Reaktor Riset Inovatif (RRI merupakan jenis MTR (Material Testing Reactor yang dipersiapkan ke depan sebagai desain reaktor baru. Daya RRI telah ditetapkan dari perhitungan neutronik dan termohidrolika teras yaitu 50 MW termal. Reaktor bertekanan 8 kgf/cm2 dan laju aliran massa pendingin primer 900 kg/s. Tantangan yang penting dalam menindak lanjuti desain reaktor ini adalah analisis desain pada sistem pendingin. Makalah ini bertujuan untuk menganalisis desain proses sistem pendingin utama reaktor RRI daya 50 MW (RRI-50 dengan menggunakan program Chemcad 6.1.4. Dalam analisis ini dilakukan perhitungan neraca massa dan energi (mass/energy balances pada sistem pendingin primer dan sekunder sebagai pendingin utama. Masing-masing sistem pendingin tersebut terdiri dari 2 jalur beroperasi secara paralel dan 1 jalur redundansi. Disamping itu untuk desain termal unit komponen telah dianalisis dengan program RELAP5, frenchcreek dan Metoda Analitik. Hasil analisis yang diperoleh adalah desain diagram sistem pendingin yang mencakup data parameter entalpi, temperatur, tekanan dan laju aliran massa pendingin untuk masing-masing jalur. Adapun hasil desain unit komponen utama pada RRI-50 adalah tangki tunda dengan volume 51,5 m3, 2 unit pompa sentrifugal dan 1 unit pompa cadangan pada pendingin primer daya 141 kW/pompa dan pendingin sekunder daya 206 kW/pompa, 2 unit penukar panas tipe shell-tube dengan koefisien termal overall 1377 W/m2.oC dan 4 unit menara pendingin yang mampu melepaskan panas ke udara dengan desain temperatur approach 5,0 oC dan temperatur range 9,0 oC. Desain sistem pendingin reaktor RRI-50 ini telah menetapkan parameter operasi sistem pendingin yaitu temperatur, tekanan dan laju aliran massa pendingin dengan mempertimbangkan tuntutan aspek keselamatan teras reaktor sehingga desain temperatur maksimum pendingin masuk ke teras 44,5 oC. Kata kunci : RRI 50 MW, desain sistem pendingin, program Chemcad 6.1.4   Innovative Research Reactor RRI

  10. SAMPAH UNTUK ENERGI: KELAYAKAN PEMANFAATAN LIMBAH ORGANIK DARI KANTIN DI LINGKUNGAN UNDIP BAGI PRODUKSI ENERGI DENGAN MENGGUNAKAN REAKTOR BIOGAS SKALA RUMAH TANGGA

    Directory of Open Access Journals (Sweden)

    Irawan Wisnu Wardana

    2012-09-01

    Full Text Available Harga minyak yang melonjak mempengaruhi aktifitas perekonomian dunia termasuk Indonesia, hal tersebut mendorong pemerintah untuk mengembangkan energi terbarukan termasuk diantaranya biogas. Limbah-limbah kantin memiliki potensi untuk menjadi sumber energi terbarukan, yaitu biogas.Limbah sisa makanan dan aktifitas dapur dalam jumlah yang cukup dari kantin di lingkungan fakultas teknik dikumpulkan, dilakukan perlakuan seperti penghalusan dan homogenisasi, lalu tahap memasukkan substrat beserta ekstrak rumen sapi sebagai sumber bakteri anaerob kedalam batch reactor dengan penambahan air sebagai variasi. Dari hasil penelitian diperoleh kesimpulan, bahwa penambahan air mempengaruhi jumlah gas yang dihasilkan. Diketahui bahwa limbah yang ditambahkan air sebanyak 64 ml, mampu menghasilkan volume gas lebih banyak dibanding yang lainnya. Umur produksi gas mampu menghasilkan gas hingga hari ke 19. Dalam penelitian didapatkan adanya penurunan dan peningkatan produksi gas. Hal ini disebabkan adanya tahap pembentukan gas yang terjadi, mulai dari tahap hidrolisis, acidogenesis, asetogenesis, dan metanogenesis

  11. PENINGKATAN KINERJA SISTEM KESELAMATAN PASIF PADA REAKTOR NUKLIR DENGAN PENAMBAHAN KOMPONEN RVACS

    Directory of Open Access Journals (Sweden)

    A. G. Abdullah

    2014-07-01

    Full Text Available Kelengkapan sistem keselamatan pasif dan inheren pada reaktor lanjut merupakan prasyarat utama. Makalah ini mengeksplorasi hasil desain konseptual sistem pembuang sisa panas pada pusat listrik tenaga nuklir berjenis Very High-Temperature Reactor. Tujuan riset ini untuk merancang sistem pembuang sisa panas pusat listrik tenaga nuklir yang terdapat pada dinding reaktor. Studi kinerja Reactor Vessel Auxliary Cooling System (RVACS dilakukan pada dua jenis pendingin yaitu Timbal-Bismut dan Liquid Salt. Panas dari dinding reaktor dihapus melalui sirkulasi alamiah pada keadaan tunak. Analisis melibatkan sistem perpindahan panas secara radiasi, konduksi dan konveksi alami. Perhitungan perpindahan panas dilakukan pada elemen reaktor vessel, dinding luar guard vessel, dan pelat pemisah. Hasil analisis kecelakaan menunjukkan kedua jenis sistem pendingin reaktor dan sistem pasif sisa pembuangan panas cukup menghapus sisa panas hasil peluruhan dengan sirkulasi alami.ABSTRACTCompleteness of passive safety systems and inherent in advanced reactors is a major prerequisite. This paper explores the results of a conceptual design of the heat removal system at the nuclear power plant (NPP type Very High-Temperature Reactor. The purpose of this research was to design the reactor vessel auxiliary cooling system (RVACS of NPP located within the reactor walls. The RVACS performance study was conducted on two types of coolant: Lead-Bismuth and Liquid Salt. Heat was removed from the reactor vessel through the natural circulation in the steady state. Analyses of heat transfer systems involved radiation, conduction and natural convection. Heat transfer calculations were performed on the reactor vessel, guard vessel, and perforated plate. The results from the accident analysis showed that both types, the reactor coolant system and the passive residual heat removal system, adequately remove remaining heat of the decay by a natural circulation.

  12. DESAIN KONSEPTUAL PERISAI RADIASI REAKTOR RRI-50

    Directory of Open Access Journals (Sweden)

    Amir Hamzah

    2015-06-01

    Full Text Available ABSTRAK DESAIN KONSEPTUAL PERISAI RADIASI REAKTOR RRI-50. Salah satu parameter yang harus dipenuhi dalam mendesain reaktor nuklir adalah desain perisai radiasi yang dapat menjamin keamanan dan keselamatan radiasi bagi pekerja dan masyarakat sekitar. Pada penelitian ini dilakukan desain perisai radiasi RRI-50 dengan elemen bakar berjenis U9Mo-Al berkerapatan tinggi dengan tipe pelat sebanyak 21 buah dan berdimensi seperti elemen bakar RSG-GAS tapi panjang aktifnya 70 cm. Konfigurasi teras terdiri dari 16 elemen bakar dan 4 elemen kendali serta 5 posisi iradiasi sehingga membentuk matriks 5 x 5. Tujuan dari penelitian ini adalah mendesain perisai radiasi dan menentukan distribusi laju dosis di daerah kerja dan di lingkungan reaktor RRI-50. Tahapan awal penelitian adalah perhitungan kuat sumber dan inventori bahan radioaktif teras reaktor dengan mensimulasikan operasi 50 MW selama 20 hari tiap siklus menggunakan program ORGEN2.1. Berdasarkan kuat sumber tersebut dan model yang dibuat menggunakan program VisEd, maka dilakukan analisis penentuan parameter perisai radiasi secara iteratif menggunakan program MCNPX. Pada tahap akhir, dilakukan analisis distribusi laju dosis di seluruh ruang di dalam dan di luar gedung reaktor juga menggunakan program MCNPX. Hasil yang diperoleh menunjukkan bahwa ketinggian permukaan air adalah 1000 cm dan kombinasi 90 cm beton berat dan 60 cm beton biasa dapat digunakan sebagai perisai biologi. Desain perisai tersebut mereduksi laju dosis menjadi 0,05 µSv/jam di Balai Operasi sementara di Balai Eksperimen dan di luar gedung reaktor menjadi 4,2 µSv/jam dan 0,03 µSv/jam pada saat reaktor beroperasi. Hasil penelitian juga menunjukkan pemasagan perisai tambahan setebal 280 cm berjarak 300 cm di depan tabung berkas neutron radial yang terbuka mereduksi laju dosis gamma dan neutron menjadi 3,3 µSv/jam dan 3,1x10-11 µSv/jam. Hasil-hasil penelitian ini menunjukkan bahwa desain perisai radiasi yang dibuat membuat reaktor

  13. PERHITUNGAN SUHU ELEMEN BAKAR REAKTOR TRIGA 2000 DALAM TABUNG SIPPING TEST MENGGUNAKAN CFD

    Directory of Open Access Journals (Sweden)

    K.A. Sudjatmi

    2015-03-01

    Full Text Available Telah dihitung suhu elemen bakar pada perangkat sipping test reaktor TRIGA 2000 Bandung. Perhitungan perlu dilakukan untuk memastikan bahwa suhu elemen bakar masih dibawah atau pada batas suhu elemen bakar yang diizinkan pada saat reaktor beroperasi, sehingga dapat dipastikan bahwa pada pelaksanaan pengujian dengan menggunakan perangkat ini, suhu masih dalam batas keselamatan. Perhitungan dilakukan dengan membuat model tabung sipping test berisi elemen bakar yang dikelilingi oleh 9 buah elemen bakar, sesuai dengan posisi tabung sipping test di teras reaktor, dengan menggunakan GAMBIT. Dimensi model disesuaikan dengan dimensi tabung dan elemen bakar dalam teras reaktor TRIGA 2000 Bandung. Pengoperasian sipping test untuk tiap elemen bakar dilakukan selama 30 menit pada daya 300 kW. Perhitungan dilakukan dengan menggunakan perangkat lunak Computational Fluid Dynamics (CFD dan sebagai inputan disesuaikan dengan parameter reaktor TRIGA 2000. Simulasi dilakukan pada pengoperasian dari 30, 60, 90, 120 150, 180 sampai 210 menit. Hasil perhitungan menunjukan bahwa suhu pusat bahan bakar dalam tabung sipping test sebesar 236,06 oC, sedangkan suhu dinding elemen bakar adalah sebesar 87,58 oC. Suhu maksimum pusat bahan bakar reaktor TRIGA 2000 pada operasi normal adalah 650 oC, dan tidak diizinkan terjadinya pendidihan di dalam teras reaktor. Jadi dapat disimpulkan bahwa pengoperasian perangkat sipping test masih sangat aman karena suhu bahan bakar berada dibawah batasan suhu bahan bakar yang diizinkan pada kondisi operasi normal demikian juga suhu dinding elemen bakar masih dibawah suhu didih air. Kata kunci: sipping test, TRIGA, elemen bakar, CFD   It has been calculated the fuel element temperature in the sipping test of Bandung TRIGA 2000 reactor. The calculation needs to be done to ascertain that the fuel element temperatures are below or at the limit of the allowable temperature fuel elements during reactor operation, ensuring that the

  14. STUDI KARAKTERISTIK PEMBENTUKAN UAP DALAM PEMBANGKIT UAP HELIKAL PADA REAKTOR MODULAR DAYA KECIL

    Directory of Open Access Journals (Sweden)

    Susyadi Susyadi

    2015-06-01

    Full Text Available Reaktor modular daya kecil (SMR sangat cocok untuk  dibangun Indonesia, terutama pada lokasi-lokasi dengan kapasitas jaringan listrik yang rendah sehingga investigasi lebih jauh tentang reaktor ini sangat diperlukan. Umumnya SMR memiliki bentuk pembangkit uap yang kompak dan terintegrasi di dalam bejana tekan. Disain tersebut menyebabkan perbedaan pendekatan dalam memproduksi uap dibandingkan reaktor nuklir konvensional yang menggunakan pembangkit uap tabung-u terbalik. Oleh karena itu tujuan dari penelitian ini adalah untuk mengetahui karakteristik uap dan pola pembentukkannya di dalam pembangkit uap tipe helikal yang banyak digunakan oleh SMR. Metoda yang dipakai adalah dengan melakukan pemodelan dan perhitungan numerik menggunakan program RELAP5. Dalam pemodelan, aliran air umpan  bertekanan dan temperatur rendah dimasukkan ke dalam tabung helikal sementara aliran fluida bertekanan dan temperatur tinggi, yang mewakili pendingin sistem primer reaktor, berada di sisi luar tabung. Hasil perhitungan menunjukkan bahwa uap yang dihasilkan oleh pembangkit uap helikal bersifat lewat jenuh yakni sekitar 25 K di atas titik jenuhnya. Hal ini memberikan keunggulan komparatif dari segi disain dan operasional pada SMR dibanding reaktor konvensional karena uap lewat jenuh yang dihasilkan dapat mengurangi kerugian turbin dan sekaligus meningkatkan efisiensi termodinamika. Kata kunci: pembangkit uap helikal, SMR, PWR, uap lewat jenuh, RELAP5   Small modular reactor (SMR is very suitable to be deployed in Indonesia especially for locations having low electrical grid capacity, so  further investigation on the characteritic of this reactor is needed. In general SMR has a compact and integrated-to-vessel steam generator design. This design implies different approach in producing steam as compared to conventional nuclear power plant  having inverted u-tube steam generator. For that reason, this research is intended to investigate the steam characteristic and

  15. Karakterisasi Unjuk Kerja Pompa Sistem Pendingin Primer Reaktor Triga 2000

    OpenAIRE

    Soekodijat, B

    2002-01-01

    KARAKTERISASI UNJUK KERJA POMPA SISTEM PENDINGIN PRIMER REAKTOR TRIGA 2000. Pompa sistem pendingin primer adalah salah satu komponen utama pada sistem pendingin Reaktor TRIGA 2000. Karakteristik unjuk kerja pompa sangat penting diketahui agar pompa dapat dioperasikan dengan baik dan aman. Penelitian dilakukan dengan cara memverifikasi kurva kinerja pompa yang diberikan oleh pabrik. Proses verifikasi dilakukan dengan mengubah-ubah laju alir pompa (dengan cara mengatur besar kecilnya pembukaan ...

  16. REAKTOR INNOVATIVE MOLTEN SALT (IMSR DENGAN SISTEM KESELAMATAN PASIF MENYELURUH

    Directory of Open Access Journals (Sweden)

    Andang Widiharto

    2015-04-01

    Full Text Available Pengembangan Teknologi Reaktor Nuklir pada masa mendatang mengarah pada peningkatan aspek keselamatan, peningkatan pendayagunaan bahan bakar, reduksi limbah radioaktif, ketahanan terhadap proliferasi bahan-bakar nuklir dan peningkatan aspek ekonomi. reaktor Innovative Molten Salt (IMSR adalah reaktor nuklir yang menggunakan bahan bakar cair berupa garam lebur fluoride (7LiF-ThF4-UF4-MaFx. Reaktor IMSR didesain sebagai reaktor pembiak termal, yaitu membiakkan U-233 dari Th-232. Hal ini untuk menjawab permasalahan sustainabilitas ketersedian sumber daya bahan bakar nuklir dan reduksi limbah radioaktif. Dalam aspek keselamatan, desain reaktor IMSR memiliki sifat inherent safe, yaitu koefisien umpan balik daya yang negatif serta memiliki fitur-fitur keselamatan pasif. Fitur-fitur keselamatan pasif terdiri dari sistem shutdown pasif, sistem pendinginan pasif pasca shutdown serta sistem pendinginan pasif untuk produk fisi. Kecelakaan yang berpotensi terjadi pada IMSR, yaitu kecelakaan kehilangan aliran bahan bakar, kecelakaan kehilangan aliran pendingin, kecelakaan kehilangan kemampuan pengambilan kalor serta kecelakaan kerusakan integritas sistem reaktor, dapat ditangani sepenuhnya secara pasif hingga mencapai kondisi shutdown selamat. Kata kunci: keselamatan pasif, inherent safe, IMSR   The next Nuclear Reactor Technology developments are directed to the increasing of the aspects of safety, fuel utility, radioactive waste reduction, proliferation retention and economy. Innovative Molten Salt Reactor (IMSR is a nuclear reactor design that uses fluoride molten salt (7LiF-ThF4-UF4-MaFx. IMSR is designed as a thermal breeder reactor, i.e. to produce U-233 from Th-232. This is the answer of natural nuclear fuel sustainability and radioactive waste problems. In term of safety aspect, IMSR design has inherent safe characteristics, i.e. negative power feedback coefficient, and passive safety features. The passive safety features are passive shutdown

  17. ANALISIS KONVEKSI ALAM TERAS REAKTOR TRIGA BERBAHAN BAKAR TIPE PELAT MENGGUNAKAN COOLOD-N2

    Directory of Open Access Journals (Sweden)

    Sudjatmi K A

    2015-06-01

    Full Text Available ABSTRAK Analisis Konveksi Alam Teras Reaktor Triga Berbahan Bakar Tipe Pelat MENGGUNAKAN COOLOD-N2. Rencana penghentian produksi elemen bakar jenis TRIGA oleh produsen elemen bakar reaktor TRIGA, sudah seharusnya diantisipasi oleh badan pengoperasi reaktor TRIGA untuk menggantikan elemen bakar tipe silinder tersebut dengan tipe pelat yang tersedia di pasaran. Pada penelitian ini dilakukan perhitungan untuk model teras reaktor dengan spesifikasi utama menggunakan bahan bakar U3Si2Al dengan pengayaan uranium  sebesar 19,75% dan tingkat muat 2,96 gU/cm3. Analisis dilakukan menggunakan program COOLOD-N2 yang tervalidasi pada konfigurasi teras TRIGA konversi berbahan bakar tipe pelat, yang tersusun atas 16 elemen bakar, 4 elemen kendali dan 1 fasilitas iradiasi yang terletak tepat di tengah teras. Hasil analisis menunjukkan bahwa dengan temperatur pendingin masuk ke teras sebesar 37oC, dan rasio faktor puncak daya radial ≤ 1,92 maka daya maksimum yang dapat dioperasikan pada moda operasi konveksi bebas adalah 600 kW. Karakteristik termohidrolika yang diperoleh antara lain adalah temperatur pendingin di sisi outlet, kelongsong dan meat masing-masing sebesar 82,39oC, 108,88oC, dan 109,02oC, pada ΔTONB (Temperature Onset of Nucleate Boiling =7,18oC dan nilai OFIR (Onset of flow instability ratio =1,03 Hasil yang diperoleh dari perhitungan ini diharapkan dapat dijadikan acuan untuk menentukan tingkat daya reaktor TRIGA berbahan bakar pelat. Kata kunci: TRIGA Konversi, COOLOD-N2, karakteristik termohidrolika, konveksi alam, elemen bakar tipe pelat.   ABSTRACT ANALYSIS OF NATURAL CONVECTION IN TRIGA REACTOR CORE PLATE TYPES FUELED USING COOLOD-N2. Any pretensions to stop the production of TRIGA fuel elements by TRIGA reactor fuel elements manufacturer should be anticipated by the operating agency of TRIGA reactor to replace the cylinder type fuel element with plate type fuel element that available on the market. In this study, the calculation of U3Si2

  18. ANALISIS PENGENDALIAN DAYA REAKTOR PCMSR DENGAN LAJU ALIR PENDINGIN

    Directory of Open Access Journals (Sweden)

    Iqbal Syafin Noha

    2015-03-01

    Full Text Available Passive Compact Molten Salt Reactor (PCMSR merupakan pengembangan dari Molten Salt Reactor (MSR yang memiliki karakter berbeda dengan lima reaktor generasi IV lainnya, yaitu menggunakan bahan bakar leburan garam. Pada reaktor MSR, garam lebur tidak digunakan sebagai pendingin tetapi digunakan sebagai medium pembawa bahan bakar. Dengan fase bahan bakar yang berupa garam lebur LiF-BeF2-ThF4-UF4, maka dapat dilakukan pengendalian daya dengan mengatur laju aliran bahan bakar dan pendingin. Tujuan penelitian ini adalah untuk mengetahui pengaruh perubahan laju alir pendingin terhadap daya reaktor PCMSR. Analisis dilakukan dengan empat jenis masukan untuk perubahan laju alir pendingin, yaitu masukan step, ramp, eksponensial, dan sinusoidal. Untuk masukan step, laju alir pendingin dibuat berubah secara mendadak. Selanjutnya untuk masukan ramp dan eksponensal, perubahan laju alir masing-masing dibuat perlahan secara linear dan mengikuti fungsi eksponensial. Kemudian untuk masukan sinusoidal, laju alir berubah naik turun secara periodik dengan memvariasikan frekuensi dari perubahan laju alir tersebut. Hasil penelitian menunjukkan bahwa penurunan laju alir pendingin sebesar 50% dari laju pendingin sebelumnya, menyebabkan daya pada reaktor PCMSR turun sebesar 63% dari daya sebelumnya. Jika terjadi fluktuasi laju aliran pendingin, maka semakin cepat perubahan tersebut, maka respon daya yang diberikan semakin kecil. Pada frekuensi yang sangat cepat, daya reaktor menjadi konstan dan cenderung tidak memiliki respon terhadap laju aliran. Hal ini merupakan salah satu aspek keselamatan reaktor, karena reaktor tidak merespon perubahan yang terlalu cepat. Kemampuan reaktor mengatur daya menyesuaikan laju aliran pendingin merupakan aspek keselamatan lainnya. Kata kunci : PCMSR, pengendalian daya, laju alir pendingin, uji respon   Passive Compact Molten Salt Reactor (PCMSR is the development of Molten Salt Reactor (MSR which has different character from other five

  19. STUDI DESAIN DOWN SCALE TERAS REAKTOR DAN BAHAN BAKAR PLTN JENIS PEBBLE BED MODULAR REACTOR – HTR 100 MWe

    Directory of Open Access Journals (Sweden)

    Slamet Parmanto

    2015-04-01

    Full Text Available Telah dilakukan penelitian terhadap teras reaktor Pebble Bed Modular Reactor (PBMR dengan daya 100 Mwe berbahan bakar UO2. Reaktor ini menggunakan moderator grafit dan helium sebagai pendingin. Studi down scale dilakukan tanpa mengubah geometri teras maupun geometri bahan bakar. Parameter yang dianalisis adalah kritikalitas teras, reaktivitas lebih, koefisien reaktivitas temperatur bahan bakar, moderator dan pendingin serta nilai ekonomis bahan bakar. Dari penelitian ini diharapkan diperoleh desain bahan bakar yang bernilai ekonomis dan memiliki fitur keselamatan melekat. Penelitian dilakukan dengan menggunakan program SRAC 2003. Hasil yang diperoleh adalah desain bahan bakar UO2 berbentuk pebble dengan pengkayaan 10% U235 dan 90 ppm racun dapat bakar Gd2O3. Nilai faktor multipilkasi effektif keff pada beginning of life (BOL adalah 1,01115 dan menjadi 1,00588 setelah 2658 hari operasi reaktor (EOL. Koefisien reaktivitas temperatur total diperoleh sebesar - 3,25900E-05 ∆k/k/K saat BOL dan -1,10615E-04 ∆k/k/K saat end of life (EOL. Reaktor ini memenuhi karakteristik keselamatan melekat ditandai dengan nilai koefisien reaktivitas temperatur yang negatif. Kata kunci: PBMR, desain bahan bakar, faktor multipilkasi effektif, reaktivitas lebih, koefisien reaktivitas temperatur.   Research of Pebble Bed Modular Reactor (PBMR 100 MWe which used UO2 fuel has been done. This reactor uses graphite as moderator and helium as coolant. Down scale studies performed without changing the core and fuel geometry. The parameter being analyzed were core criticality, excess reactivity, fuel, moderator, coolant temperature reactivity coefficient, and fuel economy. This research is expected to obtain the design that has fuel economy and inherent safety features. In this research, we have employed SRAC 2003 code. The calculation show that the UO2 pebble fuel design with 10% enrichment of U235 and 90 ppm burnable poison of Gd2O3 results in the effective multiplication

  20. ANALISIS PARAMETER KINETIK DAN TRANSIEN TERAS KOMPAK REAKTOR RSG-GAS

    Directory of Open Access Journals (Sweden)

    Iman Kuntoro

    2015-04-01

    Full Text Available Dalam rangka meningkatkan efisiensi penggunaan bahan bakar reaktor RSG-GAS telah dilakukan studi penentuan teras kompak. Hasil perhitungan parameter neutronik menunjukkan bahwa teras kompak dengan menutup empat fasilitas iradiasi (IP dengan elemen bakar dapat meningkatkan siklus operasi 23,6 %. Selanjutnya perlu dilakukan penentuan parameter kinetik dan analisis transien teras kompak untuk mengetahui keselamatan operasi reaktor. Perhitungan dilakukan dengan menggunakan program WIMS/D4 untuk generasi konstanta difusi sel elemen bakar dan MTRDYN untuk menentukan parameter kinetik dan analisis transien. Hasil perhitungan menunjukkan bahwa harga fraksi neutron kasip total teras kompak naik 2 % dan umur neutron serempak turun 8,3 % dibandingkan dengan teras setimbang. Temperatur maksimum bahan bakar saat transien pada daya awal 1 W adalah 71,64 0C dan pada daya 1 MW adalah 129,60 0C. Hasil ini menunjukkan bahwa teras kompak RSG-GAS aman digunakan sebagai teras alternatif. Kata kunci: parameter kinetik, transien, reaktor   For increasing the efficiency of fuel element of the RSG-GAS reactor, some alternative configuration has been searched to obtain a compact core configuration. Calculation result of the neutronics parameters that the compact core with insertion fuel element to all irradiation facility (IP can increase operation cycle length to about 23.6 %. Then, it is necessary to calculate the kinetic parameters and transient analysis of the compact core to verify the reactor operation safety. Calculations were performed by means of WIMS/D4 and MTRDYN code for generation of cell diffusion constants and for kinetic parameters and transient analysis respectively. The result showed that the total delayed neutron fraction of compact core increases by 2 % and the prompt neutron lifetime decreases 8.3 % compared to the equilibrium core. Maximum temperature of the fuel element at transient at initial power of 1 W is 71.64 0C and at the power 1 MW is 126

  1. Isotopic composition of precipitation at the station Ljubljana (Reaktor, Slovenia – period 2007–2010

    Directory of Open Access Journals (Sweden)

    Polona Vreča

    2014-12-01

    Full Text Available The stable isotopic composition of hydrogen and oxygen (δ2H and δ18O and the tritium activity (A were monitored in monthly collected precipitation at Ljubljana (Reaktor during the period 2007–2010. Monthly and yearly isotope variations are discussed and compared with those observed over the period 1981–2006 and with the basic meteorological parameters for Ljubljana (Bežigrad and Ljubljana (Hrastje stations for the period 2007−2010. The mean values for δ2H and δ18O, weighted by precipitation amount at Ljubljana (Reaktor, are –59.4 ‰ and –8.71 ‰. The reduced major axis local meteoric water line (LMWLRMA is δ2H = (8.19 ± 0.22×δ18O + (11.52 ± 1.97, while the precipitation weighted least square regression results in LMWLPWLSR-Re δ2H = (7.94 ± 0.21×δ18O + (9.76 ± 1.93. The lack of significant difference in the LMWL slopes indicates a relatively homogeneous distribution of monthly precipitation as well as the small number of low-amount monthly precipitation events with low deuterium excess. The deuterium excess weighted mean value is 10.3 ‰ which indicates the prevailing influence of the Atlantic air masses. The temperature coefficient of δ18O is 0.30 ‰/°C. Tritium activity in monthly precipitation shows typical seasonal variations, with a weighted mean tritium activity in this period of 8.5 TU. No decrease of mean annual activity is observed.

  2. Disain Sistem Pemantauan Lingkungan Untuk Evaluasi Lepasan Radionuklida dari Subsistem pada Kecelakaan Reaktor Daya PWR

    Directory of Open Access Journals (Sweden)

    Sri Kuntjoro

    2013-03-01

    Full Text Available PLTN. (Pembangkit Listrik Tenaga Nuklir sebagai sumber energi baru dipilih sebagai alternatif, karena memiliki berbagai kelebihan yaitu ramah lingkungan, pasokan bahan bakar yang tidak bergantung musim, serta harganya yang dapat bersaing dengan pembangkit listrik yang lain. Namun demikian, adanya keraguan sebagian masyarakat tentang keselamatan radiasi PLTN, maka pemerintah harus bisa meyakinkan tentang operasi PLTN yang aman dan selamat. Penelitian tentang disain sistem pemantauan lingkungan untuk evaluasi lepasan radionuklida dari subsistem reaktor dan lingkungan akibat terjadinya kecelakaan pada reaktor daya telah dilakukan. Penelitian dilakukan dengan melakukan perhitungan sebaran radionuklida ke subsistem dan lingkungan serta membuat sistim monitoring radiasi di lingkungan. Sistem monitoring lingkungan terdiri dari system pencacah radiasi, sistem peringatan dini, sistem pengukuran meteorologi, sistem GPS dan system GIS. Sistem pencacah radiasi digunakan untuk mencatat data radiasi, sistem pengukuran meteorologi digunakan untuk mencatat data arah dan kecepatan angin, sedangkan sistem GPS digunakan untuk menentukan data posisi pengukuran. Data tersebut kemudian dikirimkan ke system akuisisi data untuk ditransmisikan ke pusat kendali. Pengumpulan dan pengiriman data dilakukan melalui SMS menggunakan perangkat modem yang ditempatkan di ruang kendali. Ruang kendali menerima data dari berbagai tempat pengukuran. Dalam hal ini ruang kendali memiliki fungsi sebagai SMS gateway. Sistem ini dapat memvisualisasi untuk lokasi pengukuran yang berbeda. Selanjutnya, data posisi dan data radiasi diintegrasikan dengan peta digital. Integrasi sistem tersebut kemudian divisualisasikan dalam personal komputer. Untuk posisi pengukuran terlihat langsung di peta dan untuk data radiasi ditampilkan di monitor dengan tanda lingkaran merah atau hijau yang digunakan sebagai pemonitor batas aman radiasi. Bila tanda lingkaran berwarna merah maka akan menyalakan alarm di

  3. PENGARUH DAYA DAN DURASI OPERASI REAKTOR TERHADAP KONSENTRASI 3H DAN 14C DI AIR SISTEM PENDINGIN PRIMER REAKTOR RSG-GAS

    Directory of Open Access Journals (Sweden)

    Pande Made Udiyani

    2015-03-01

    Full Text Available Telah dilakukan penelitian terhadap pengaruh daya dan durasi operasi reaktor terhadap konsentrasi 3H dan 14C dalam air sistem pendingin primer reaktor RSG-GAS. Keberadaan nuklida 3H dan 14C di dalam air sistem pendingin primer reaktor RSG-GAS merupakan hasil produk fisi dan aktivasi. Nuklida radioaktif ini mempunyai potensi bahaya radiasi interna dan eksterna, karena mempunyai umur paro yang panjang yaitu 12,26 tahun untuk 3H dan 5568 tahun untuk 14C, sehingga mempunyai dampak radiologis yang sangat berarti. Analisis dan pengukuran contoh cuplikan air pendingin primer dilakukan dengan menggunakan alat LSC (Liquid Scintillation Counter. Tujuan dari penelitian ini adalah mengetahui pengaruh daya dan durasi operasi reaktor terhadap konsentrasi nuklida 3H dan 14C dalam air sistem pendingin primer, korelasi konsentrasi kedua nuklida dengan komponen sistem reaktor yang berkaitan dengan penuaan komponen, dan estimasi penerimaan radiasi terhadap pekerja radiasi di reaktor RSG-GAS dalam kaitan dengan keselamatan daerah kerja dan keselamatan personil. Hasil penelitian menunjukkan bahwa besarnya konsentrasi 3H dan 14C di air sistem pendingin primer reaktor RSG-GAS sebanding dengan daya yang dibangkitkan dan durasi operasi reaktor. Pertambahan konsentrasi 3H dan 14C di kolam reaktor RSG-GAS yang pesat setelah lima tahun pertama operasi reaktor diperkirakan karena intensitas pengoperasian reaktor yang tinggi, dan adanya proses akumulasi nuklida yang mempunyai umur paro yang panjang. Hasil penelitian ini dapat dimanfaatkan untuk mengkaji keselamatan operasi reaktor, keselamatan personil, keselamatan kerja, dan proses penuaan reaktor. Kata kunci : air pendingin primer, 3H, 14C, reaktor RSG-GAS   The influence of reactor power and operation duration on concentration of 3H and 14C in primary coolant water system RSG-GAS reactor has been studied. The existence of nuclides 3H and 14C in primary coolant system RSG-GAS reactor is a result of fission product and

  4. PEMBUATAN SERBUK U-6Zr DENGAN PENGKAYAAN URANIUM 19,75 % UNTUK BAHAN BAKAR REAKTOR RISET

    Directory of Open Access Journals (Sweden)

    Masrukan Masrukan

    2016-03-01

    Full Text Available ABSTRAK PEMBUATAN SERBUK PADUAN U-6Zr DENGAN PENGKAYAAN URANIUM 19,75 % UNTUK BAHAN BAKAR REAKTOR RISET. Telah dilakukan pembuatan serbuk paduan U-6Zr dengan pengkayaan 19,75 % untuk bahan bakar reaktor riset. Pembuatan bahan bakar U-6Zr ini dalam rangka mencari bahan bakar baru yang mempunyai densitas tinggi untuk mengganti bahan bakar yang sudah ada U3Si2-Al. Tujuan dari percobaan ini untuk mengetahui sifat-sifat serbuk paduan U- 6Zr yang diperoleh dari proses hydriding-dehydriding sebagai kandidat bahan bakar reaktor riset. Serbuk yang diperoleh dari proses hydriding-dehydriding dikenai pengujian, diantaranya pungujian komposisi kimia, densitas, kandungan hidrogen, fasa dan sifat termal. Hasil pengujian komposisi kimia menunjukkan beberapa unsur seperti Al, Ca, Cu, dan Ni melebihi batas yang diijinkan dimana masing-masing unsur terdapat sebesar 202,21 ppm; 214,05 ppm; 61,25 ppm dan 134,53 ppm. Pada pengujian diperolah densitas serbuk U-6Zr sebesar 13,58 g/cm3 dan pada pengujian kandungan hidrogen sisa diperoleh kandungan hidrogen sebesar 0,16 %. Untuk pengujian fasa, diperoleh fasa αU dan δU, sedangkan pada pengujian sifat termal yakni transformasi temperatur terdapat dua puncak yakni puncak pertama terjadi pada temperatur 274 hingga 311 oC dan puncak kedua terjadi pada temperatur 493 hingga 527oC. Puncak pertama terjadi reaksi endotermik dengan menyerap panas sebesar ∆H = 6,23 cal/g tetapi tidak terbentuk fasa baru, sedangkan puncak kedua terjadi reaksi eksotermik dengan mengeluarkan panas sebesar ∆H = -9.34 cal/g dan terbentuk fasa αZr. Sementara itu, dari pengujian kapasitas panas pada temperatur 34 hingga 75 oC, terjadinya penurunan nilai kapasitas panas yang disertai dengan penyerapan panas. Pada temperatur yang lebih tinggi hingga temperatur 437oC nilai kapasitas panas menjadi lebih kecil disertai pengeluaran panas. Reaksi termokimia antara Zr dengan hidrogen sisa menunjukkan terbentuknya fasa αZr yang diindikasikan oleh reaksi

  5. Fire modeling of the Heiss Dampf Reaktor containment

    Energy Technology Data Exchange (ETDEWEB)

    Nicolette, V.F. [Sandia National Labs., Albuquerque, NM (United States); Yang, K.T. [Notre Dame Univ., IN (United States)

    1995-09-01

    This report summarizes Sandia National Laboratories` participation in the fire modeling activities for the German Heiss Dampf Reaktor (HDR) containment building, under the sponsorship of the United States Nuclear Regulatory Commission. The purpose of this report is twofold: (1) to summarize Sandia`s participation in the HDR fire modeling efforts and (2) to summarize the results of the international fire modeling community involved in modeling the HDR fire tests. Additional comments, on the state of fire modeling and trends in the international fire modeling community are also included. It is noted that, although the trend internationally in fire modeling is toward the development of the more complex fire field models, each type of fire model has something to contribute to the understanding of fires in nuclear power plants.

  6. Karakterisasi Densitas Grafit Sebagai Kandidat Bahan Reaktor Temperatur Tinggi

    OpenAIRE

    Heri Hardiyanti; Slamet Pribadi; Dadang; Jan Setiawan

    2016-01-01

    -Characterization on graphite density has been done. The characterizations were done by analyzed X-ray diffraction pattern using Rietveld method compared to the density measurement according to ASTM C373 and ASTM C559. Microstructure observation by optical microscope was done to prove the density characteristic of graphite electrode. The results showed the graphite electrode was 2H graphite allotrope with hexagonal crystal system and its space group is P 63 m c. Rietveld analysis for lattic...

  7. OPTIMASI DESAIN TERMOHIDROLIKA TERAS DAN SISTEM PENDINGIN REAKTOR RISET INOVATIF DAYA TINGGI

    Directory of Open Access Journals (Sweden)

    Endiah Puji Hastuti

    2015-10-01

    Full Text Available ABSTRAK OPTIMASI DESAIN TERMOHIDROLIKA TERAS DAN SISTEM PENDINGIN REAKTOR RISET INOVATIF DAYA TINGGI. Implementasi reaktor inovasi telah diterapkan pada berbagai reaktor riset baru yang saat ini sedang dibangun.  Pada saat ini BATAN sedang merancang desain konseptual reaktor riset daya tinggi yang telah masuk pada tahap optimasi desain. Spesifikasi desain konseptual reaktor riset inovatif adalah reaktor tipe kolam berpendingin air dan reflektor D2O. Teras reaktor memiliki kisi 5x5 dengan 16 bahan bakar dan 4 batang kendali. Teras reaktor berada di dalam tabung berisi D2O yang berfungsi sebagai posisi iradiasi. Daya reaktor 50 MW didesain untuk membangkitkan fluks neutron termal sebesar 5x1014 n/cm2s. Teras reaktor berbentuk kompak dan menggunakan bahan bakar U9Mo-Al dengan tingkat muat uranium 7-9 gU/cm3. Desain termohidrolika yang mencakup pemodelan, perhitungan dan analisis kecukupan pendingin dibuat sinergi dengan desain fisika teras agar keselamatan reaktor terjamin. Makalah ini bertujuan menyampaikan hasil analisis perhitungan termohidrolika teras dan sistem reaktor riset inovatif pada kondisi tunak. Analisis dilakukan menggunakan program perhitungan yang telah tervalidasi, masing-masing adalah Caudvap, PARET-ANL, Fluent dan ChemCad 6.4.1. Hasil perhitungan menunjukkan bahwa pembangkitan panas yang tinggi dapat dipindahkan tanpa menyebabkan pendidihan dengan menerapkan desain teras reaktor bertekanan, di samping itu desain awal komponen utama sistem pembuangan panas yang terintegrasi telah dilakukan, sehingga konseptual desain termohidrolika RRI-50 dapat diselesaikan. Kata kunci : reaktor riset inovatif, Caudvap, PARET-ANL, Fluent, ChemCad 6.4.1.   ABSTRACT THERMALHYDRAULIC DESIGN AND COOLING SYSTEM OPTIMIZATION OF THE HIGH POWER INOVATIVE RESEARCH REACTOR. Reactor innovation has been implemented in a variety of new research reactors that currently are being built. At this time BATAN is designing a conceptual design of the high power

  8. High temperature thermoelectric energy conversion

    Science.gov (United States)

    Wood, Charles

    1987-01-01

    The theory and current status of materials research for high-temperature thermoelectric energy conversion are reviewed. Semiconductors are shown to be the preferred class of materials for this application. Optimization of the figure of merit of both broadband and narrow-band semiconductors is discussed as a function of temperature. Phonon scattering mechanisms are discussed, and basic material guidelines are given for reduction of thermal conductivity. Two general classes of materials show promise for high temperature figure of merit (Z) values, namely the rare earth chalcogenides and the boron-rich borides. The electronic transport properties of the rare earth chalcogenides are explicable on the basis of degenerate or partially degenerate n-type semiconductors. Boron and boron-rich borides exhibit p-type hopping conductivity, with detailed explanations proposed for the transport differing from compound to compound. Some discussion is presented on the reasons for the low thermal conductivities in these materials. Also, ZTs greater than one appear to have been realized at high temperature in many of these compounds.

  9. PENGARUH KONSENTRASI ZrO2 TERHADAP KORELASI PERPINDAHAN PANAS NANOFLUIDA AIR-ZrO2 UNTUK PENDINGIN REAKTOR

    OpenAIRE

    K.A. Sudjatmi; K. Kamajaya; Efrizon Umar

    2015-01-01

    Sejalan dengan perkembangan konsep keselamatan pasif pada sistem keselamatan PLTN, maka sistem perpindahan panas konveksi alam memegang peranan penting. Pemakaian nanofluid sebagai fluida pendingin pada sistem keselamatan nuklir dapat digunakan pada Sistem Pendingin Teras Darurat dan Sistem Pendingin Pengungkung Luar Reaktor. Beberapa peneliti telah melakukan studi desain konseptual aplikasi nanofluid untuk meningkatkan keselamatan AP1000 dan sistem pendingin teras darurat pada reaktor daya e...

  10. DESAIN KONSEPTUAL TERAS REAKTOR RISET INOVATIF BERBAHAN BAKAR URANIUM MOLIBDENUM DARI ASPEK NEUTRONIK

    Directory of Open Access Journals (Sweden)

    Tukiran Surbakti

    2015-03-01

    Full Text Available Manfaat yang luas dari penggunaan reaktor riset membuat banyak negara membangun reaktor riset baru. Kecenderungan saat ini adalah reaktor tipe reaktor serbaguna (MPR dengan teras yang kompak untuk mendapatkan fluks neutron yang tinggi dengan daya yang relatif sedang atau rendah. Reaktor riset yang ada di Indonesia yang paling muda usianya sudah berumur 25 tahun. Oleh karena itu diperlukan desain reaktor riset baru sebagai alternatif, disebut reaktor riset inovatif (RRI, kelak pengganti reaktor riset yang sudah ada. Tujuan dari riset ini mendapatkan konfigurasi teras setimbang reaktor riset yang optimal dengan kriteria memiliki fluks neutron termal minimum sebesar 2,5x1014 n/cm2 s pada daya 20 MW (minimum, memiliki panjang operasi satu siklus lebih dari 40 hari dan penggunaan bahan bakar yang paling efisien. Desain neutronik dilakukan untuk bahan bakar baru U-9Mo-Al dengan kerapatan bervariasi dan jenis reflektor yang bervariasi. Desain dilakukan dengan paket program WIMSD-5B dan BATAN-FUEL. Hasil desain konseptual menyajikan 4 konfigurasi teras yaitu 5×5, 5×7, 6×5 dan 6×6. Hasil optimasi menunjukkan bahwa teras setimbang reaktor RRI dengan konfigurasi 5×5, tingkat muat 235U sebesar 450 g, reflektor berilium, fluks neutron termal maksimum di daerah reflektor sebesar 3,33×1014 neutron cm-2s-1 dan panjang siklus 57 hari merupakan desain teras reaktor riset inovatif yang paling optimal. Kata kunci: desain konseptual, bahan bakar uranium-molibdenum,berilium, D2O, WIMS, BATAN-FUEL   The multipurpose of research reactor utilization make many countries build the new research reactor. Trend of this reactor for this moment is multipurpose reactor type with a compact core to get high neutron flux at the low or medium level of power. The research newest reactor in Indonesia right now is already 25 year old. Therefore, it is needed to design a new research reactor, called innovative research reactor (IRR and then as an alternative to replace the old

  11. PENGARUH GRID PEJARAK DAN NOZZLE TERHADAP PARAMETER TERMOHIDROLIKA PERANGKAT BAHAN BAKAR REAKTOR AP1000

    Directory of Open Access Journals (Sweden)

    Muh. Darwis Isnaini

    2015-03-01

    Full Text Available Grid pejarak berfungsi secara mekanik untuk menambah kekuatan perangkat bahan bakar nuklir (BBN dari getaran yang ditimbulkan oleh aliran pendingin yang mengalir melalui celah subkanal di dalam perangkat BBN. Oleh sebab itu perlu dilakukan analisis termohidrolika reaktor AP1000 pada kondisi tunak untuk mengetahui pengaruh dipasangnya grid pejarak pada perangkat BBN. Metodologi yang dilakukan melakukan perhitungan penurunan tekanan teras, fluks massa dan koefisien hantaran kalor pada perangkat BBN tanpa grid pejarak dan variasi jumlah grid. Pada analisis subkanal terpanas (SKP ditekankan pada perbandingan termohidrolika reaktor AP1000 pada kondisi tunak antara SKP tanpa grid pejarak dan SKP dengan 8/2 grid-nozzle, dengan menggunakan kode COBRA-EN. Dibandingkan SKP tanpa grid pejarak, maka pemasangan 8/2 grid-nozzle menyebabkan penurunan tekanan teras meningkat 3,74 kali lipat dari 73,99 kPa menjadi 276,88 kPa, fluks massa pendingin dan koefisien hantaran kalor berfluktuasi pada daerah sekitar grid pejarak, menghasilkan proses pengambilan panas oleh pendingin menjadi lebih efektif. Penurunan tekanan yang semakin besar juga akan berakibat pada nilai fluks kalor kritis (CHF bertambah besar. Karena daya reaktor tidak berubah, maka fluks kalor cenderung berubah kecuali pada daerah grid, oleh sebab itu nilai DNBR menjadi bertambah besar yang berarti marjin keselamatannya juga bertambah besar. Perhitungan untuk SKP dengan 8/2 grid-nozzle dibandingkan dengan desain diperoleh hasil penurunan tekanan teras sebesar 276,88 kPa (perbedaan 0,68%, temperatur outlet pendingin sebesar 325,54oC (perbedaan 0,21%, fluks kalor maksimum sebesar 1635,16 kW/m2 (perbedaan 0,03% dan MDNBR sebesar 2,48 (lebih besar 14,06% dari batas minimum korelasi W-3. Penambahan 8/2 grid-nozzle memberikan angka keselamatan yang lebih tinggi. Kata kunci: Pengaruh grid pejarak dan nozzle, analisis termohidrolika, AP1000, COBRA-EN.   One of the spacer grids function was to increase the

  12. Pengembangan Reaktor Fotokatalitik Rotating Drum untuk Pengolahan Air Limbah Industri Tekstil

    Directory of Open Access Journals (Sweden)

    Cholid Syahroni

    2015-11-01

    Full Text Available Reaksi oksidasi fotokatalitik memiliki potensi untuk mendegradasi senyawa organik hingga tingkat mineralisasi, sehingga tidak meninggalkan residu (sludge. Penelitian ini bertujuan membuat reaktor fotokatalitik rotating drum dan mengaplikasikan pada industri tekstil. Langkah percobaan meliputi pembuatan katalis TiO2 secara anodizing serta karakterisasi dengan XRD dan SEM, pembuatan reaktor fotokatalitik  rotating drum dan uji coba degradasi air limbah industri tekstil. Proses anodizing dilakukan dengan bias potensial sebesar 40 volt selama 2 jam menggunakan elektrolit etilen glikol yang mengandung amonium fluorida dan air. Uji karakterisasi secara XRD dan SEM menunjukkan bahwa struktur kristal TiO2 adalah anatase dengan ukuran kristalit 8–19 nm. Bentuk kristal nanotube, dengan diameter 30–110 nm. Hasil uji coba menunjukkan bahwa  degradasi secara fotokatalitik dengan penambahan H2O2 0,15% terhadap air limbah bisa menurunkan COD 72,12% dalam waktu 2 jam. 

  13. PENGARUH PROSES PENGINTEGRASIAN PANAS TERHADAP KONVERSI AMONIAK PADA INTERCOOLER REAKTOR AMONIAK DENGAN ANALISIS EKSERGI DAN PINCH

    Directory of Open Access Journals (Sweden)

    Muhammad Djoni Bustan

    2012-02-01

    Full Text Available Amoniak merupakan salah satu senyawa penting yang banyak digunakan dalam industri kimia sebagai bahan baku dan produk. Salah satu unit pabrik amoniak yang dikaji membutuhkan gas alam sebesar 13.627 MMBTU sebagai bahan bakar (fuel dan 24.570 MMBTU sebagai bahan baku untuk memproduksi 1 ton amoniak cair. Belum optimalnya sistim pendinginan antar unggun (bed dan belum maksimalnya pemanfaatan panas hasil reaksi di reaktor amoniak menyebabkan konversi reaksi masih rendah. Analisis eksergi yang merupakan kombinasi antara Hukum Termodinamika I dan II,  digunakan untuk mengetahui titik- titik kehilangan panas yang paling tinggi, yaitu pada bed 1, bed 2, dan bed 3. Analisis pinch yang diterapkan pada reaktor tersebut dapat dibuat suatu sistem jaringan alat penukar panas yang baru pada ammonia converter, sehingga diperoleh konversi yang lebih baik.

  14. ANALISIS POLA MANAJEMEN BAHAN BAKAR DESAIN TERAS REAKTOR RISET TIPE MTR

    Directory of Open Access Journals (Sweden)

    Lily Suparlina

    2015-03-01

    Full Text Available Parameter neutronik dibutuhkan dalam mendesain teras reaktor riset. Reaktor riset jenis MTR (Material Testing Reactor sangat diminati karena dapat digunakan baik untuk riset dan juga produksi radio isotop. Reaktor riset yang ada saat ini sudah tua sehingga dibutuhkan desain reaktor yang mempunyai teras kompak. Desain teras reaktor riset yang sudah ada saat ini belum cukup memadai untuk memenuhi persyaratan di dalam UCD yang telah ditetapkan yaitu fluks neutron termal di teras 1x1015 n/cm2s, oleh karena itu perlu dibuat desain teras reaktor baru sebagai alternatif yang kompak dan dapat menghasilkan fluks neutron tinggi. Telah dilakukan perhitungan dan analisis terhadap manajemen bahan bakar desain teras kompak dengan konfigurasi teras 5x5, berbahan bakar U9Mo-Al dan tinggi teras aktif 70 cm. Tujuan dari riset ini untuk memperoleh fluks neutron di teras memenuhi kebutuhan seperti yang telah ditetapkan di UCD dengan panjang siklus operasi minimum 20 hari pada daya 50 MW. Perhitungan dilakukan dengan menggunakan paket program komputer WIMSD-5B untuk menggenerasi tampang lintang makroskopik bahan bakar dan Batan-FUEL untuk memperoleh nilai parameter neutronik serta Batan-3DIFF untuk perhitungan nilai reaktivitas batang kendali. Perhitungan parameter neutronik teras reaktor riset ini dilakukan untuk bahan bakar U-9Mo-Al dengan tingkat muat bervariasi dan 2 macam pola pergantian bahan bakar yaitu teras segar dan teras setimbang. Hasil analisis menunjukkan bahwa pada teras segar, tingkat muat 235U sebesar 360 gram, 390 gram dan 450 gram memenuhi kriteria keselamatan dan kriteria penerimaan di UCD dengan nilai fluks neutron termal di teras lebih dari 1x1015 n/cm2s dan panjang siklus >20 hari, sedangkan pada teras setimbang panjang siklus dapat terpenuhi hanya untuk tingkat muat 450 gram. Kata kunci: desain teras reaktor, bahan bakar UMo, pola bahan bakar, WIMS, BATAN-FUEL   Research reactor core design needs neutronics parameter calculation use computer

  15. KARAKTERISASI RADIONUKLIDA PADA TIAP SUB-SISTEM KESELAMATAN REAKTOR DAYA BERBAHAN BAKAR MOX

    Directory of Open Access Journals (Sweden)

    Pande Made Udiyani

    2015-04-01

    Full Text Available Pengganti Bahan bakar UO2, yang tergolong uranium pengkayaan rendah, adalah bahan bakar MOX yang mempunyai pengkayaan yang lebih tinggi. Bahan bakar MOX mempunyai kandungan plutonium dan nuklida dari golongan aktinida yang lebih tinggi dibandingkan bahan bakar UO2, yang akan menghasilkan karakteristik radionuklida yang berbeda untuk setiap sub-sistem reaktor daya. Analisis radionuklida untuk setiap sub-sistem keselamatan pada reaktor daya berbahan bakar MOX dilakukan untuk mengetahui karakteristik radionuklida khususnya plutonium dan aktinida yang akan menimbulkan dampak radiasi dari lepasan radionuklida tersebut. Analisis dilakukan dengan cara menghitung dan mengamati radionuklida untuk setiap sub-sistem keselamatan pada operasi normal dan kecelakaan (small LOCA, large LOCA, severe accident untuk reaktor PWR berkapasitas 1000 MWe. Disimpulkan bahwa penggunaan bahan bakar MOX dapat menambah konsekuensi radiologis ke lingkungan dan masyarakat, terutama karena inventori yang lebih besar termasuk dari radionuklida transuranic dan dari golongan aktinida, antara lain: Pu-239, Am-241, Cm-242, Pu-240, Pu-241 dan Pu-242. Kata kunci: karakteristik nuklida, reaktor daya, bahan bakar, MOX   Substitute UO2 fuel that low enrichment of uranium is that MOX fuel has a higher enrichment. MOX fuel has a content of plutonium and actinide nuclides a higher than UO2 fuel, which will produce different characteristics of radionuclides for each sub-system of power reactors. Analyzis of radionuclide for each safety sub-system at MOX power reactor aims to determine the characteristics of radionuclides, especially plutonium and actinides consequences. Analyzis has done by calculating and observing the radionuclide for each safety sub-system in normal operation and accident (small LOCA, large LOCA, and severe accident on PWR-1000 reactors. It can concluded that the use of MOX fuel can add to the radiological consequences to the environment and public, mainly because a

  16. Low temperature thermal-energy storage

    Energy Technology Data Exchange (ETDEWEB)

    Segaser, C.S.; Christian, J.E.

    1979-03-01

    This report evaluates currently available techniques and estimated costs of low temperature thermal energy storage (TES) devices applicable to Integrated Community Energy Systems (ICES) installations serving communities ranging in size from approximately 3000 (characterized by an electrical load requirement of 2 MWe) to about 100,000 population (characterized by an electrical load requirement of 100 MWe). Thermal energy in the form of either hotness or coldness can be stored in a variety of media as sensible heat by virtue of a change in temperature of the material, or as latent heat of fusion in which the material changes from the liquid phase to the solid phase at essentially a constant temperature. Both types of material are considered for TES in ICES applications.

  17. Energy storage via high temperature superconductivity (SMES)

    Energy Technology Data Exchange (ETDEWEB)

    Mikkonen, R. [Tampere Univ. of Technology (Finland)

    1998-10-01

    The technology concerning high temperature superconductors (HTS) is matured to enabling different kind of prototype applications including SMES. Nowadays when speaking about HTS systems, attention is focused on the operating temperature of 20-30 K, where the critical current and flux density are fairly close to 4.2 K values. In addition by defining the ratio of the energy content of a novel HTS magnetic system and the required power to keep the system at the desired temperature, the optimum settles to the above mentioned temperature range. In the frame of these viewpoints a 5 kJ HTS SMES system has been designed and tested at Tampere University of Technology with a coil manufactured by American Superconductor (AMSC). The HTS magnet has inside and outside diameters of 252 mm and 317 mm, respectively and axial length of 66 mm. It operates at 160 A and carries a total of 160 kA-turns to store the required amount of energy. The effective magnetic inductance is 0.4 H and the peak axial field is 1.7 T. The magnet is cooled to the operating temperature of 20 K with a two stage Gifford-McMahon type cryocooler with a cooling power of 60 W at 77 K and 8 W at 20 K. The magnetic system has been demonstrated to compensate a short term loss of power of a sensitive consumer

  18. Solar energy control system. [temperature measurement

    Science.gov (United States)

    Currie, J. R. (Inventor)

    1981-01-01

    A solar energy control system for a hot air type solar energy heating system wherein thermocouples are arranged to sense the temperature of a solar collector, a space to be heated, and a top and bottom of a heat storage unit is disclosed. Pertinent thermocouples are differentially connected together, and these are employed to effect the operation of dampers, a fan, and an auxiliary heat source. In accomplishing this, the differential outputs from the thermocouples are amplified by a single amplifier by multiplexing techniques. Additionally, the amplifier is corrected as to offset by including as one multiplex channel a common reference signal.

  19. High-Temperature Thermoelectric Energy Conversion

    Science.gov (United States)

    Wood, C.

    1987-01-01

    Theory of thermoelectric energy conversion at high temperatures and status of research on conversion materials reviewed in report. Shows highest values of thermoelectric figure of merit, Z, found in semiconductor materials. Semiconductors keep wide choice of elements and compounds. Electrical properties tailored to particular application by impurity doping and control of stoichiometry. Report develops definition of Z useful for comparing materials and uses it to evaluate potentials of different classes of materialsmetals, semiconductors, and insulators.

  20. Analisis Dimensional Reaktor Berpengaduk Statis untuk Produksi Biodiesel

    Directory of Open Access Journals (Sweden)

    Akhmad Irfan

    2016-10-01

    Full Text Available Biodiesel production can be done using static mixing reactor (SMR. The production by this method requires less energy than blade agitator. However, the use of elements in the helix-shaped stirrer reactors causing large pressure drop. The other factors that affect the flow in the SMR can be determined using dimensional analysis. Dimensional analysis can be used to eliminate the variables that are not required so that can be done to optimize the energy used in the SMR design. The variables that influence the pressure drop (ΔP in the SMR can be formulated into mathematical equation as: Total irreversibility due to the use of a static mixer in the SMR tested is 0.237 W.

  1. PENGARUH GEMPA PATAHAN LEMBANG TERHADAP FLEKSIBILITAS PIPA DAN KEGAGALAN NOZEL PERALATAN SISTEM PENDINGIN PRIMER REAKTOR TRIGA 2000 BANDUNG

    Directory of Open Access Journals (Sweden)

    H.P. Raharjo

    2012-02-01

    Full Text Available Gempa bumi di suatu instalasi nuklir dapat menyebabkan terjadinya kerusakan sistem peralatan karena adanya perubahan fleksibilitas pipa akibat beban berlebih pada sistem perpipaannya. Beban dari sistem perpipaan dapat membebani nozel peralatan seperti pompa, penukar panas, dll. Apabila beban tersebut terlalu besar dan melebihi beban yang diizinkan akan mengakibatkan kegagalan nozel peralatan. Penelitian ini menganalisis besarnya beban-beban yang terjadi di semua nozel  sistem pendingin primer Reaktor TRIGA 2000 Bandung. Analisis dilakukan dengan bantuan perangkat lunak Caesar II yang berbasis metode elemen hingga (finite element method. Acuan analisis yang digunakan adalah code ASME B31.1 yang mengatur tentang perancangan sistem perpipaan untuk sistem pembangkit daya (Power Piping. Hasil analisis menunjukkan bahwa gaya yang terjadi pada nozel masukan pompa arah aksial (FZ melebihi batas yang diijinkan. Oleh karena itu perlu dilakukan modifikasi terhadap jalur perpipaan sistem pendingin tersebut agar nozel tidak menerima gaya yang berlebih. Penyangga pipa titik(node 22 di jalur PriOut dilepas dan/atau dipindahkan pada nozel masukkan pompa. Perpipaan sistem pendingin primer reaktor TRIGA 2000 Bandung akan aman beroperasi jika terjadi gempa.yang berasal dari patahan Lembang Kata kunci : gempa bumi, patahan, perpipaan, reaktor, sistem pendingin

  2. PEMODELAN KOLIMATOR DI RADIAL BEAM PORT REAKTOR KARTINI UNTUK BORON NEUTRON CAPTURE THERAPY

    Directory of Open Access Journals (Sweden)

    Bemby Yulio Vallenry

    2015-03-01

    Full Text Available Salah satu metode terapi kanker adalah Boron Neutron Capture Therapy (BNCT. BNCT memanfaatkan tangkapan neutron oleh 10B yang terendapkan pada sel kanker. Keunggulan BNCT dibandingkan dengan terapi radiasi lainnya adalah tingkat selektivitas yang tinggi karena tingkatannya adalah sel. Pada penelitian ini dilakukan pemodelan kolimator di radial beamport reaktor Kartini sebagai dasar pemilihan material dan manufature kolimator sebagai sumber neutron untuk BNCT. Pemodelan ini dilakukan dengan simulasi menggunakan perangkat lunak Monte Carlo N-Particle versi 5 (MCNP 5. MCNP 5 adalah suatu paket program untuk memodelkan sekaligus menghitung masalah transpor partikel dengan mengikuti sejarah hidup neutron semenjak lahir, bertranspor pada bahan hingga akhirnya hilang karena mengalami reaksi penyerapan atau keluar dari sistem. Pemodelan ini menggunakan variasi material dan ukurannya agar menghasilkan nilai dari tiap parameter-parameter yang sesuai dengan rekomendasi I International Atomic Energy Agency (IAEA untuk BNCT, yaitu fluks neutron epitermal (Фepi > 9 n.cm-2.s-1, rasio antara laju dosis neutron cepat dan fluks neutron epitermal (Ḋf/Фepi 0,7. Berdasarkan hasil optimasi dari pemodelan ini, material dan ukuran penyusun kolimator yang didapatkan yaitu 0,75 cm Ni sebagai dinding kolimator, 22 cm Al sebagai moderator dan 4,5 cm Bi sebagai perisai gamma. Keluaran berkas radiasi yang dihasilkan dari pemodelan kolimator radial beamport yaitu Фepi = 5,25 x 106 n.cm-2s-1, Ḋf/Фepi =1,17 x 10-13 Gy.cm2.n-1, Ḋγ/Фepi = 1,70 x 10-12 Gy.cm2.n-1, Фth/Фepi = 1,51 dan J/Фepi = 0,731. Berdasarkan penelitian ini, hasil optimasi 5 parameter sebagai persyaratan kolimator untuk BNCT yang keluar dari radial beam port tidak sepenuhnya memenuhi kriteria yang direkomendasikan oleh IAEA sehingga perlu dilakukan penelitian lebih lanjut agar tercapainya persyaratan IAEA. Kata kunci: BNCT, radial beamport, MCNP 5, kolimator   One of the cancer therapy methods is

  3. PENGEMBANGAN MODEL UNTUK SIMULASI KESELAMATAN REAKTOR PWR 1000 MWe GENERASI III+ MENGGUNAKAN PROGRAM KOMPUTER RELAP5

    Directory of Open Access Journals (Sweden)

    Andi Sofrany Ekariansyah

    2015-04-01

    Full Text Available Reaktor daya PWR AP1000 yang didesain oleh Westinghouse adalah reaktor Generasi III+ pertama yang telah menerima persetujuan desain dari U.S. Nuclear Regulatory Commission (NRC. Saat ini utilitas China telah memulai pembangunan beberapa unit AP1000 di dua tapak terpilih untuk rencana operasi pada 2013-2015. AP1000 sebagai desain PWR berdasarkan teknologi teruji dari desain PWR lainnya yang dibuat oleh Westinghouse dengan penguatan pada sistem keselamatan pasif dengan demikian dapat dipertimbangkan untuk dibangun di Indonesia bila mengacu pada persyaratan pada PP 43/2006 mengenai Perijinan Reaktor Nuklir. Namun demikian, desain tersebut perlu diverifikasi oleh Technical Support Organization (TSO independen sebelum dapat dibangun di Indonesia. Verifikasi dapat dilakukan menggunakan paket program RELAP5 dalam bentuk analisis kecelakaan. Selama ini analisis kecelakaan PLTN dilakukan untuk tipe PWR 1000 MWe dari generasi II atau tipe konvensional. Mengingat saat ini referensi yang menggambarkan teknologi AP1000 yang menyertakan teknologi keselamatan pasif sudah tersedia maka dilakukan kegiatan pemodelan yang nantinya dapat digunakan untuk melakukan analisis kecelakaan. Metode pengembangan model mengacu pada pedoman IAEA yang terdiri dari pengumpulan data instalasi, pengembangan engineering data dan penyusunan input deck, verifikasi dan validasi data input. Model yang berhasil dikembangkan secara umum telah mewakili sistem AP1000 secara keseluruhan dan dianggap sebagai model dasar. Model tersebut telah diverifikasi dan divalidasi dengan data desain yang terdapat pada referensi dimana respon parameter termohidraulika menunjukkan perbedaan hasil ± 3% selain untuk parameter penurunan tekanan teras yang lebih rendah 13%. Sebagai model dasar, input deck yang diperoleh dapat dikembangkan lebih lanjut dengan mengintegrasikan pemodelan sistem keselamatan, sistem proteksi, dan sistem kendali yang spesifik AP1000 untuk keperluan simulasi keselamatan yang lebih

  4. Perancangan dan Simulasi MRAC untui Proses Pengendalian Temperatur pada Continuous Stirred Tank Reactor (CSTR

    Directory of Open Access Journals (Sweden)

    Amelia Sylvia

    2014-03-01

    Full Text Available Temperatur merupakan salah satu variabel proses dasar yang dikendalikan untuk menjaga suhu cairan di dalam reaktor. Model Reference Adaptive Controller (MRAC dengan MIT rule dipilih untuk mencapai spesifikasi respon yang diinginkan pada CSTR. Beban yang bervariasi berupa debit aliran likuid yang masuk ke dalam reaktor dapat menyebabkan perubahan parameter yang mempengaruhi perubahan temperatur output produk pada CSTR. Sebuah simulasi dilakukan dengan menggunakan MATLAB dan hasilnya dianalisa. Respon plant dapat melakukan adaptasi parameter – parameter kontrolernya cukup baik pada nilai gain adaptasi dengan rentang 0.00000010000 sampai 0.00000000001. Waktu yang dibutuhkan untuk mengatasi beban yang bervariasi berupa debit aliran yang masuk ke dalam reaktor dengan nilai yang maksimal (1.5 m^3/min menghasilkan respon plant lebih cepat 42 detik dari pada debit aliran masuk dengan nilai yang nominal (1 m^3/min 63 detik dan minimal (0.5 m^3/min 75 detik.

  5. Daily temperature integration: a simulation study to quantify energy consumption

    Energy Technology Data Exchange (ETDEWEB)

    Koerner, O. [The Royal Veterinary and Agricultural University, Taastrup (Denmark). Department of Agricultural Sciences, Section Horticulture; Bakker, M.J.; Heuvelink, E. [Wageningen University (Netherlands). Department of Plant Sciences, Horticultural Production Chains Group

    2004-03-01

    A combined greenhouse climate and control model was used to study energy consumption in year-round cut chrysanthemum. Temperature was either controlled for energy saving with temperature integration within 24 h using the margin between heating and ventilation temperature b as control (TI) or the temperature integration regime was restricted within 24 h by a set point for negative temperature difference between average day and average night temperature T{sub DIF} to attain a temperature regime for stem length control (TI{sub DIF}). Energy consumption was reduced by both regimes compared to a standard regime according to commercial practice when heating in winter was shifted to nighttime using a screen. With increasing weather fluctuations in spring and autumn, weekly energy consumption could decrease by more than 60% for TI with {+-}6{sup o}C temperature bandwidth. With TI{sub DIF} in the same period, only 37 or 17% (T{sub DIF} of -6 and -12{sup o}C, respectively) less energy was used than with a standard recommended climate regime (TP). In general, TI{sub DIF} reduced energy demand compared to TP, but energy saving was higher with TI. In deciding whether to apply either TI or TI{sub DIF}, the actual cultivation period is the most important criterion. Controlling stem length with a negative temperature difference in spring and autumn has the highest additional costs, control with almost no negative day to night temperature difference is possible in summer; during winter, both temperature control regimes result in an almost similar greenhouse climate. (author)

  6. VERIFIKASI PAKET PROGRAM MVP-II DAN SRAC2006 PADA KASUS TERAS REAKTOR VERA BENCHMARK.

    Directory of Open Access Journals (Sweden)

    Jati Susilo

    2015-03-01

    Full Text Available Dalam penelitian ini dilakukan verifikasi perhitungan benchmark VERA pada kasus Zero Power Physical Test (ZPPT teras reaktor Watts Bar 1. Reaktor tersebut merupakan jenis PWR kelas 1000 MWe yang didesain oleh Westinghouse, tersusun dari 193 perangkat bahan bakar 17×17 dengan 3 jenis pengkayaan UO2 yaitu 2,1wt%, 2,619wt% dan 3,1wt%. Perhitungan nilai k-eff dan distribusi faktor daya dilakukan pada siklus operasi pertama teras dengan kondisi beginning of cycle (BOC dan hot zero power (HZP. Posisi batang kendali dibedakan menjadi uncontrolled (semua batang kendali berada di luar teras, dan controlled (batang kendali Bank D didalam teras. Paket program komputer yang digunakan dalam perhitungan adalah MVP-II dan SRAC2006 modul CITATION dengan data pustaka tampang lintang ENDF/B-VII.0. Hasil perhitungan menunjukkan bahwa perbedaan nilai k-eff teras pada kondisi controlled dan uncontrolled antara referensi dengan MVP-II (-0,07% dan -0,014% dan SRAC2006 (0,92% dan 0,99% sangat kecil atau masih dibawah 1%. Perbedaan faktor daya maksimum teras pada kondisi controlled dan uncontrolled dengan referensi dengan MVP-II adalah 0,38% dan 1,53%, sedangkan dengan SRAC2006 adalah 1,13% dan -2,45%. Dapat dikatakan bahwa kedua paket program komputer menunjukkan hasil perhitungan yang sesuai dengan nilai referensi. Dalam hal penentuan kekritisan teras, maka hasil perhitungan MVP-II lebih konservatif dibandingkan dengan SRAC2006. Kata kunci : MVP-II, SRAC2006, PWR, VERA   In this research, verification calculation for VERA core physics benchmark on the Zero Power Physical Test (ZPPT of the nuclear reactor Watts Bar 1. The reactor is a 1000 MWe class of PWR designed by Westinghouse, arranged from 193 unit of 17×17 fuel assembly consisting 3 type enrichment of UO2 that are 2.1wt%, 2.619wt% and 3.1wt%. Core power factor distribution and k-eff calculation has been done for the first cycle operation of the core at beginning of cycle (BOC and hot zero power (HZP. In this

  7. using energy efficient using energy efficient temperature sensor

    African Journals Online (AJOL)

    eobe

    the world economy and in daily experience this is why automatic systems are being preferred over manual system [1] .... for Analog to Digital Conversion (ADC) the resolution will be poor as the input voltage will only drive up to ... Therefore temperature (C) = Vin/0.01 = Digital. Reading x 0.4883 [7]. 3.3 Design Analysis of the ...

  8. Lithium-ion Energy Storage at Very Low Temperatures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Li-ion batteries with specific energy >180 Wh/kg, calendar life (>15years), and a wide operating temperature range (-60oC to 60oC) are crucial for the...

  9. High-Temperature Coatings Offer Energy Savings

    Science.gov (United States)

    2012-01-01

    The U.S. X-Plane Program included the first-of-its-kind research in aerodynamics and astronautics with experimental vehicles, including the first aircraft to break the sound barrier; the first aircraft to fly in excess of 100,000, then 200,000, and then 300,000 feet; and the first aircraft to fly at three, four, five, and then six times the speed of sound. During the 1990s, NASA started developing a new thermal protection material to test on the X-33 and X-34 supersonic aircraft. The X-33 was intended to demonstrate the technologies needed for a new reusable launch vehicle and was projected to reach an altitude of approximately 50 miles and speeds of more than Mach 11. The X-34, a small, reusable technology demonstrator for a launch vehicle, was intended to reach an altitude of 250,000 feet and fly at speeds of Mach 8. As a result of its research and development efforts, NASA s Ames Research Center invented the Protective Ceramic Coating Material (PCCM). Applied to a surface, the thin, lightweight coating could protect the material underneath from extreme temperatures. The capability of the technology came from its emissivity, which radiated heat away from the surface it covered, thereby decreasing the amount of heat transferred to the underlying material. PCCM not only increased the capability of materials to withstand higher temperatures, it also exhibited impressive thermal shock, vibration, and acoustic performance. In addition, it proved to be resistant to abrasion and mechanical damage and was also environmentally safe, due to it being water-based and containing no solvents. Even though funding for the X-33 and X-34 ended in 2001, PCCM continued on a path of innovation.

  10. Junction Temperature Aware Energy Efficient Router Design on FPGA

    DEFF Research Database (Denmark)

    Thind, Vandana; Sharma, Shivani; Minwer, M H

    2015-01-01

    Energy, Power and efficiency are very much related to each other. To make any system efficient, Power consumed by it must be minimized or we can say that power dissipation should be less. In our research we tried to make a energy efficient router design on FPGA by varying junction temperature...

  11. Energy and exergy analysis of low temperature district heating network

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2012-01-01

    Low temperature district heating with reduced network supply and return temperature provides better match of the low quality building heating demand and the low quality heating supply from waste heat or renewable energy. In this paper, a hypothetical low temperature district heating network...... is designed to supply heating for 30 low energy detached residential houses. The network operational supply/return temperature is set as 55 °C/25 °C, which is in line with a pilot project carried out in Denmark. Two types of in-house substations are analyzed to supply the consumer domestic hot water demand...... optimization procedure and the network simultaneous factor. Through the simulation, the overall system energy and exergy efficiencies are calculated and the exergy losses for the major district heating system components are identified. Based on the results, suggestions are given to further reduce the system...

  12. Low Temperature District Heating for Future Energy Systems

    DEFF Research Database (Denmark)

    Schmidt, Dietrich; Kallert, Anna; Blesl, Markus

    2017-01-01

    of the building stock. Low temperature district heating (LTDH) can contribute significantly to a more efficient use of energy resources as well as better integration of renewable energy (e.g. geothermal or solar heat), and surplus heat (e.g. industrial waste heat) into the heating sector. LTDH offers prospects......The building sector is responsible for more than one third of the final energy consumption of societies and produces the largest amount of greenhouse gas emissions of all sectors. This is due to the utilisation of combustion processes of mainly fossil fuels to satisfy the heating demand...... for both the demand side (community building structure) and the supply side (network properties or energy sources). Especially in connection with buildings that demand only low temperatures for space heating. The utilisation of lower temperatures reduces losses in pipelines and can increase the overall...

  13. A Wind Energy Powered Wireless Temperature Sensor Node

    Directory of Open Access Journals (Sweden)

    Chuang Zhang

    2015-02-01

    Full Text Available A wireless temperature sensor node composed of a piezoelectric wind energy harvester, a temperature sensor, a microcontroller, a power management circuit and a wireless transmitting module was developed. The wind-induced vibration energy harvester with a cuboid chamber of 62 mm × 19.6 mm × 10 mm converts ambient wind energy into electrical energy to power the sensor node. A TMP102 temperature sensor and the MSP430 microcontroller are used to measure the temperature. The power management module consists of LTC3588-1 and LT3009 units. The measured temperature is transmitted by the nRF24l01 transceiver. Experimental results show that the critical wind speed of the harvester was about 5.4 m/s and the output power of the harvester was about 1.59 mW for the electrical load of 20 kΩ at wind speed of 11.2 m/s, which was sufficient to power the wireless sensor node to measure and transmit the temperature every 13 s. When the wind speed increased from 6 m/s to 11.5 m/s, the self-powered wireless sensor node worked normally.

  14. A wind energy powered wireless temperature sensor node.

    Science.gov (United States)

    Zhang, Chuang; He, Xue-Feng; Li, Si-Yu; Cheng, Yao-Qing; Rao, Yang

    2015-02-27

    A wireless temperature sensor node composed of a piezoelectric wind energy harvester, a temperature sensor, a microcontroller, a power management circuit and a wireless transmitting module was developed. The wind-induced vibration energy harvester with a cuboid chamber of 62 mm × 19.6 mm × 10 mm converts ambient wind energy into electrical energy to power the sensor node. A TMP102 temperature sensor and the MSP430 microcontroller are used to measure the temperature. The power management module consists of LTC3588-1 and LT3009 units. The measured temperature is transmitted by the nRF24l01 transceiver. Experimental results show that the critical wind speed of the harvester was about 5.4 m/s and the output power of the harvester was about 1.59 mW for the electrical load of 20 kΩ at wind speed of 11.2 m/s, which was sufficient to power the wireless sensor node to measure and transmit the temperature every 13 s. When the wind speed increased from 6 m/s to 11.5 m/s, the self-powered wireless sensor node worked normally.

  15. Isotopic Temperatures and Symmetry Energy in Spectator Fragmentation

    Science.gov (United States)

    de Napoli, M.; Sfienti, C.; Bianchin, S.; Le Fèvre, A.; Łukasik, J.; Trautmann, W.; Adrich, P.; Aumann, T.; Bacri, C. O.; Barczyk, T.; Bassini, R.; Boiano, C.; Botvina, A. S.; Boudard, A.; Brzychczyk, J.; Chbihi, A.; Cibor, J.; Czech, B.; Ducret, J.-E.; Emling, H.; Frankland, J.; Hellström, M.; Henzlova, D.; Kezzar, K.; Immé, G.; Iori, I.; Johansson, H.; Lafriakh, A.; Le Gentil, E.; Leifels, Y.; Lynch, W. G.; Lühning, J.; Lynen, U.; Majka, Z.; Mocko, M.; Müller, W. F. J.; Mykulyak, A.; Orth, H.; Otte, A. N.; Palit, R.; Pawłowski, P.; Pullia, A.; Raciti, G.; Rapisarda, E.; Sann, H.; Schwarz, C.; Simon, H.; Sümmerer, K.; Tsang, M. B.; Volant, C.; Wallace, M.; Weick, H.; Wiechula, J.; Wieloch, A.; Zwieglinski, B.

    2008-04-01

    The influence of the isotopic composition in the breakup of projectile spectators at relativists energies has been studied at the GSI laboratory with the ALADiN spectrometer. Besides a primary beam of 124Sn, also secondary beams of 124La and 107Sn produced at the FRS fragment separator have been used in order to extend the range of isotopic compositions. The breakup temperatures obtained from the double ratios of isotopic yields have been extracted and compared with the limiting-temperature expectation. Moreover, from isoscaling analysis an apparent symmetry-energy term of the EOS has been extracted.

  16. Measuring information-based energy and temperature of literary texts

    Science.gov (United States)

    Chang, Mei-Chu; Yang, Albert C.-C.; Eugene Stanley, H.; Peng, C.-K.

    2017-02-01

    We apply a statistical method, information-based energy, to quantify informative symbolic sequences. To apply this method to literary texts, it is assumed that different words with different occurrence frequencies are at different energy levels, and that the energy-occurrence frequency distribution obeys a Boltzmann distribution. The temperature within the Boltzmann distribution can be an indicator for the author's writing capacity as the repertory of thoughts. The relative temperature of a text is obtained by comparing the energy-occurrence frequency distributions of words collected from one text versus from all texts of the same author. Combining the relative temperature with the Shannon entropy as the text complexity, the information-based energy of the text is defined and can be viewed as a quantitative evaluation of an author's writing performance. We demonstrate the method by analyzing two authors, Shakespeare in English and Jin Yong in Chinese, and find that their well-known works are associated with higher information-based energies. This method can be used to measure the creativity level of a writer's work in linguistics, and can also quantify symbolic sequences in different systems.

  17. Articulated Multimedia Physics, Lesson 13, Internal Energy, Heat, and Temperature.

    Science.gov (United States)

    New York Inst. of Tech., Old Westbury.

    As the thirteenth lesson of the Articulated Multimedia Physics Course, instructional materials are presented in this study guide with relation to internal energy, heat, and temperature. The topics are concerned with collisions, thermometers, friction forces, degrees Centigrade and Fahrenheit, calories, Brownian motion, and state changes. The…

  18. PENENTUAN KADAR RADIONUKLIDA PADA LIMBAH CAIR PABRIK GALVANIS DENGAN METODE ANALISIS AKTIVASI NEUTRON THERMAL REAKTOR KARTINI

    Directory of Open Access Journals (Sweden)

    P. Dwijananti

    2016-09-01

    Full Text Available Kadar unsur-unsur pada limbah cair pabrik galvanis perlu diketahui, hal ini penting dilakukan sebelum limbah cair pabrik galvanisdibuang ke lingkungan. MetodeAnalisis Aktivasi Neutron (AAN digunakan untuk analisis kualitatif dan kuantitatif. Metode kualitatifdapat mengetahui unsur yang terkandung, sedangkan analisis kuantitatif untuk mengetahui kadar unsurnya. Sampel limbah cairdiaktivasi menggunakan sumber neutron dari Reaktor Kartini, kemudian dicacah menggunakan spektrometri- , setelah itudianalisis secara kualitatif dan kuantitatif. Hasil analisis kualitatif teridentifikasi 7 unsur pada limbah cair pabrik galvanis. Unsurtersebut adalah Mangan (Mn, Zirkon (Zr, Chlorine (Cl, Seng(Zn, Bromine (Br, Natrium (Na, dan Besi (Fe. Analisis kuantitatifmenunjukkan kadar unsur tersebut yaitu : Mn (1,89 - 1,92.10-9gram/l, Zr (5,65 - 5,66.10-4gram/l, Cl (4,39 - 4,50.10-8 gram/l, Zn(6,47 - 6,65.10-5 gram/l, Br (1,32 -1,35.10-3gram/l, Na (4,18 - 4,19.10-4 gram/l, dan Fe (5,65.10-5 gram/l. Berdasarkanperhitungan dan setelah dibandingkan dengan baku mutu limbah dan baku mutu air, maka limbah cair pabrik galvanis dalam batasaman. The content of elements in liquid waste of galvanise factory are recommeded to be determined first before the waste is expelled intoenvironment. The Neutron Activation Analysis was used to have qualitative and quantitative analysis. The qualitative method wasused to identify the element contained,while the quantitative one was used to measure the decay rate of the element.Tified, thosewere Mangan (Mn, Zirkon (Zr, Chlorine (Cl, Zink (Zn, Bromine (Br, Sodium (Na and Ferrum (Fe. The quantitative analysisshows the content of each elements as follows. Mn (1.89 – 1.92 x 10-9 g/l; Zr (5.65 – 5.66 x 10-4 g/l; Cl (4.39 – 4.50 x 10-8 g/l; Zn(6.47 – 6.65 x 10-5 g/l, Br (1.32 – 1.35 x 10-3 g/l; Na (4.18 – 4.19 x 10-4 g/l, and Fe (5.65 x 10-5 g/l. Based on the calculation andafter comparing it to the

  19. Investigation of lithium sulphate for high temperature thermal energy storage

    Science.gov (United States)

    Bayon, Alicia; Liu, Ming; Bruno, Frank; Hinkley, Jim

    2017-06-01

    Lithium sulphate (Li2SO4) was evaluated as a solid-solid PCM material to be coupled with concentrated solar power (CSP) technologies. The energy is stored in a cubic crystalline phase that is formed at temperatures above 576°C and can potentially be discharged at temperatures as low as 150°C, providing both sensible and latent thermal energy storage in a hybrid sensible-latent system. These operational conditions are appropriate for current CSP technologies based on subcritical steam Rankine power cycles. Results from thermal cycling experiments in air showed no change in energy storage capacity after 15 cycles. There was up to a 5% reduction in latent thermal capacity and 0.95% in total thermal capacity after 150 cycles in air. In our paper, we evaluate a hybrid sensible-latent thermal energy storage system based on lithium sulphate from an economic and technical performance point of view, demonstrating its potential as a high temperature thermal energy storage material.

  20. Optical Fiber High Temperature Sensor Instrumentation for Energy Intensive Industries

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, Kristie L.; Wang, Anbo; Pickrell, Gary R.

    2006-11-14

    This report summarizes technical progress during the program “Optical Fiber High Temperature Sensor Instrumentation for Energy Intensive Industries”, performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. The objective of this program was to use technology recently invented at Virginia Tech to develop and demonstrate the application of self-calibrating optical fiber temperature and pressure sensors to several key energy-intensive industries where conventional, commercially available sensors exhibit greatly abbreviated lifetimes due primarily to environmental degradation. A number of significant technologies were developed under this program, including • a laser bonded silica high temperature fiber sensor with a high temperature capability up to 700°C and a frequency response up to 150 kHz, • the world’s smallest fiber Fabry-Perot high temperature pressure sensor (125 x 20 μm) with 700°C capability, • UV-induced intrinsic Fabry-Perot interferometric sensors for distributed measurement, • a single crystal sapphire fiber-based sensor with a temperature capability up to 1600°C. These technologies have been well demonstrated and laboratory tested. Our work plan included conducting major field tests of these technologies at EPRI, Corning, Pratt & Whitney, and Global Energy; field validation of the technology is critical to ensuring its usefulness to U.S. industries. Unfortunately, due to budget cuts, DOE was unable to follow through with its funding commitment to support Energy Efficiency Science Initiative projects and this final phase was eliminated.

  1. Activation energy for oxygen chemisorption on carbon at low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Teng, H.; Hsieh, C.T. [National Cheng Kung Univ., Tainan (Taiwan, Province of China). Dept. of Chemical Engineering

    1999-01-01

    The kinetics of oxygen chemisorption on resin chars were investigated in this study. The Elovich equation was employed to facilitate the interpretation of the chemisorption process. It was found that the activation energy for chemisorption is not constant and varies with surface coverage. This observation can be explained by a distributed kinetic parameter model, here implemented as a distributed activation energy model. The energy distribution model reveals that the amount of mass uptake obtained in a typical chemisorption study does not involve full coverage of all of the active sites on carbon. It is concluded that the information on active sites obtained from low-temperature chemisorption cannot be directly applied to gasification at higher temperatures.

  2. Effects of environmental temperature and dietary energy on energy partitioning coefficients of female broiler breeders.

    Science.gov (United States)

    Pishnamazi, A; Renema, R A; Paul, D C; Wenger, I I; Zuidhof, M J

    2015-10-01

    With increasing disparity between broiler breeder target weights and broiler growth potential, maintenance energy requirements have become a larger proportion of total broiler breeder energy intake. Because energy is partitioned to growth and egg production at a lower priority than maintenance, accurate prediction of maintenance energy requirements is important for practical broiler breeder feed allocation decisions. Environmental temperature affects the maintenance energy requirement by changing rate of heat loss to the environment. In the ME system, heat production (energy lost) is part of the maintenance requirement (ME). In the current study, a nonlinear mixed model was derived to predict ME partitioning of broiler breeder hens under varied temperature conditions. At 21 wk of age, 192 Ross 708 hens were individually caged within 6 controlled environmental chambers. From 25 to 41 wk, 4 temperature treatments (15°C, 19°C, 23°C, and 27°C) were randomly assigned to the chambers for 2-week periods. Half of the birds in each chamber were fed a high-energy (HE; 2,912 kcal/kg) diet, and half were fed a low-energy (LE; 2,790 kcal/kg) diet. The nonlinear mixed regression model included a normally distributed random term representing individual hen maintenance, a quadratic response to environmental temperature, and linear ADG and egg mass (EM) coefficients. The model assumed that energy requirements for BW gain and egg production were not influenced by environmental temperature because hens were homeothermic, and the cellular processes for associated biochemical processes occurred within a controlled narrow core body temperature range. Residual feed intake (RFI) and residual ME (RME) were used to estimate efficiency. A quadratic effect of environmental temperature on broiler breeder MEm was predicted ( broiler breeders fed the HE diet.

  3. Size-dependent cohesive energy, melting temperature, and Debye temperature of spherical metallic nanoparticles

    Science.gov (United States)

    Qu, Y. D.; Liang, X. L.; Kong, X. Q.; Zhang, W. J.

    2017-06-01

    It is necessary to theoretically evaluate the thermodynamic properties of metallic nanoparticles due to the lack of experimental data. Considering the surface effects and crystal structures, a simple theoretical model is developed to study the size dependence of thermodynamic properties of spherical metallic nanoparticles. Based on the model, we have considered Co and Cu nanoparticles for the study of size dependence of cohesive energy, Au and Cu nanoparticles for size dependence of melting temperature, and Cu, Co and Au nanoparticles for size dependence of Debye temperature, respectively. The results show that the size effects on melting temperature, cohesive energy and Debye temperature of the spherical metallic nanoparticles are predominant in the sizes ranging from about 3 nm to 20 nm. The present theoretical predictions are in agreement with available corresponding experimental and computer simulation results for the spherical metallic nanoparticles. The model could be used to determine the thermodynamic properties of other metallic nanoparticles to some extent.

  4. Temperature compensation in piezoelectric energy harvesters using shape memory alloys

    Science.gov (United States)

    Rhimi, Mohamed; Lajnef, Nizar

    2011-04-01

    Harvested vibration energy is typically considered as an alternative power source for sensors' networks for health and usage monitoring in civil and mechanical structures. The longevity, and hence the efficacy, of these sensors is severely limited by the levels of generated power. Piezoelectric vibration harvesters have been widely used given their energy conversion ability and relatively high mechanical to electrical coupling properties. Several techniques can be applied to improve these properties and to cancel external environmental effects such as temperature variations. In this paper, the temperature compensation of the response characteristics of a bimorph cantilever Lead zirconate titanate (PZT) piezoelectric beam, through a combination with shape memory alloys, is studied. A mathematical model, based on onedimensional linear piezoelectricity equations and one dimensional constitutive behavior of shape memory alloys, is derived. The model describes the effect of temperature deviations on the theoretical harvestable energy levels as well as the compensation methodology. Proof of concept experimental results are also presented. The voltage response transfer functions are measured at different temperatures to show the induced effect by shape memory alloys.

  5. Towards Energy Efficiency: Forecasting Indoor Temperature via Multivariate Analysis

    Directory of Open Access Journals (Sweden)

    Juan Pardo

    2013-09-01

    Full Text Available The small medium large system (SMLsystem is a house built at the Universidad CEU Cardenal Herrera (CEU-UCH for participation in the Solar Decathlon 2013 competition. Several technologies have been integrated to reduce power consumption. One of these is a forecasting system based on artificial neural networks (ANNs, which is able to predict indoor temperature in the near future using captured data by a complex monitoring system as the input. A study of the impact on forecasting performance of different covariate combinations is presented in this paper. Additionally, a comparison of ANNs with the standard statistical forecasting methods is shown. The research in this paper has been focused on forecasting the indoor temperature of a house, as it is directly related to HVAC—heating, ventilation and air conditioning—system consumption. HVAC systems at the SMLsystem house represent 53:89% of the overall power consumption. The energy used to maintain temperature was measured to be 30%–38:9% of the energy needed to lower it. Hence, these forecasting measures allow the house to adapt itself to future temperature conditions by using home automation in an energy-efficient manner. Experimental results show a high forecasting accuracy and therefore, they might be used to efficiently control an HVAC system.

  6. Pyroelectric Ceramics as Temperature Sensors for Energy System Applications

    Science.gov (United States)

    Silva, Jorge Luis

    Temperature is continuously monitored in energy systems to ensure safe operation temperatures, increase efficiency and avoid high emissions. Most of energy systems operate at high temperature and harsh environments to achieve higher efficiencies, therefore temperature sensing devices that can operate under these conditions are highly desired. The interest has increased in temperature sensors capable to operate and in harsh environments and temperature sensors capable to transmit thermal information wirelessly. One of the solutions for developing harsh environment sensors is to use ceramic materials, especially functional ceramics such as pyroelectrics. Pyroelectric ceramics could be used to develop active sensors for both temperature and pressure due to their capabilities in coupling energy among mechanical, thermal, and electrical domains. In this study, two different pyroelectric materials were used to develop two different temperature sensors systems. First, a high temperature sensor was developed using a lithium niobate (LiNbO3) pyroelectric ceramic. With its Curie temperature of 1210 °C, lithium niobate is capable to maintain its pyroelectric properties at high temperature making it ideal for temperature sensing at high temperature applications. Lithium niobate has been studied previously in the attempt to use its pyroelectric current as the sensing mechanism to measure temperatures up to 500 °C. Pyroelectric coefficient of lithium niobate is a function of temperature as reported in a previous study, therefore a dynamic technique is utilized to measure the pyroelectric coefficient of the lithium niobate used in this study. The pyroelectric coefficient was successfully measured up to 500 °C with coefficients ranging from -8.5 x 10 -5 C/m2 °C at room temperature to -23.70 x 10 -5 C/m2 °C at 500 °C. The lithium niobate sensor was then tested at higher temperatures: 220 °C, 280 °C, 410 °C and 500 °C with 4.31 %, 2.1 %, 0.4 % and 0.6 % deviation

  7. Combining pressure and temperature control in dynamics on energy landscapes

    Science.gov (United States)

    Hoffmann, Karl Heinz; Christian Schön, J.

    2017-05-01

    Complex systems from science, technology or mathematics usually appear to be very different in their specific dynamical evolution. However, the concept of an energy landscape with its basins corresponding to locally ergodic regions separated by energy barriers provides a unifying approach to the description of complex systems dynamics. In such systems one is often confronted with the task to control the dynamics such that a certain basin is reached with the highest possible probability. Typically one aims for the global minimum, e.g. when dealing with global optimization problems, but frequently other local minima such as the metastable compounds in materials science are of primary interest. Here we show how this task can be solved by applying control theory using magnesium fluoride as an example system, where different modifications of MgF2 are considered as targets. In particular, we generalize previous work restricted to temperature controls only and present controls which simultaneously adjust temperature and pressure in an optimal fashion.

  8. Relation between Debye temperature and energy band gap of semiconductors

    Science.gov (United States)

    Ullrich, Bruno; Bhowmick, Mithun; Xi, Haowen

    2017-04-01

    The work addresses an unresolved topic in solid-state physics, i.e., the dependence of the Debye temperature (TD) on the energy band gap (Eg) of semiconducting materials. The systematic calculation of TD by using the ratio of sound velocity and lattice constant from the literature resulted in the relation TD∝exp(Eg). The exponential relationship is confirmed by a theoretical model based on the microscopic analysis of the electrical conductivity in metals and semiconductors.

  9. Air temperature and energy consumption feedbacks within urbanized areas

    Science.gov (United States)

    Ginzburg, A. S.; Demchenko, P. F.

    2017-09-01

    In the 21st century, the climate of expanding megacities and urbanized areas is increasingly forming and changing under the influence of the growing power consumption of the urban economy. To understand the urban climate dynamic and estimate the energy needs of cities in the 21st century, it is necessary to consider not only global and regional climatic factors, but also the presence of feedback between temperature and energy consumption in urbanized areas. This feedback can be both negative and positive, and their significance depends essentially on the climate and landform of the region, system of electricity and heat supply of a city, and some other factors. This article describes the main factors of formation and development of temperature and energy-consumption feedback within urbanized areas in cold and warm seasons when indoor heating or air conditioning is being used. The role of advection in strengthening and weakening of this feedback is studied. The estimates of the parameter and coefficient of feedback strengthening with the influence of anthropogenic heat fluxes and advection on the urban air temperature are presented.

  10. A low cost high temperature sun tracking solar energy collector

    Science.gov (United States)

    Perkins, G. S.

    1977-01-01

    The design and economic evaluation of a low cost high temperature two axis sun tracking solar energy collector are described. The collector design is specifically intended for solar energy use with the freedom of motion about its two control axes being limited only to the amplitude required to track the sun. An examination of the performance criteria required in order to track the sun and perform the desired solar energy conversion is used as the starting point and guide to the design. This factor, along with its general configuration and structural aspect ratios, is the significant contributor to achieving low cost. The unique mechanical design allows the control system to counter wide tolerances that will be specified for the fabrication of the azimuth frame and perform within a small tracking error.

  11. Pengaruh Laju Alir Inlet Reaktor MSL terhadap Reduksi BOD, COD, TSS, dan Minyak/Lemak Limbah Cair Industri Minyak Goreng

    Directory of Open Access Journals (Sweden)

    Salmariza Sy

    2017-06-01

    Full Text Available This research was conducted by treating edible oil industry wastewater used Multi Soil Layering (MSL method. The MSL reactor was built from a 200x120x200 cm concrete basin. Andisol soil was mixed with sawdust and fine charcoal at each ratio 5:1:1 based on dry weight as an impermeable layer. The flow rate variations were 250, 500, 1000, and 1500 L/m2.day. The observed pollutant parameters were BOD, COD, TSS, oil/fat, and pH. The results showed that MSL reactor was effective to decrease the pollutant content of edible oil industry wastewater. The reactor could reduce concentration of effluent parameters below standard except for oil/fat parameters at high flow rates. In the effluent was found BOD 0.66-14.22 mg/L, COD 5-69 mg/L, TSS 9-26 mg/L, and oil/fat 2-9 mg/L. The flow rate had an effect on reduction efficiency of BOD, COD, TSS, and oil/fat but did not effect pH as all flow rate could raise pH 6.37-6.95 became pH 6.99-7.24. The lower the flow rate the higher the reduction efficiency. The reduction efficiency at flow rates 250 and 1500 L/m2 days for BOD were 99% and 86%, COD were 96% and 71%, TSS were 88% and 77%, and oil/fat were 80% and 60%.ABSTRAK  Penelitian ini dilakukan dengan mengolah air limbah industri minyak goreng menggunakan metoda Multi Soil Layering (MSL. Reaktor MSL dibuat dari beton berbentuk bak ukuran 200x120x200 cm. Tanah andisol dicampur dengan serbuk gergaji dan arang halus pada rasio masing-masing 5:1:1 berdasarkan berat kering sebagai penyusun lapisan impermeable. Variasi laju alir yaitu 250, 500, 1000, dan 1500 L/m2.hari. Parameter pencemar yang dianalisis meliputi BOD, COD, TSS, minyak/lemak, dan pH. Hasil penelitian menunjukkan bahwa reaktor MSL sangat efektif untuk menurunkan kandungan zat pencemar limbah cair industri minyak goreng. Reaktor dapat mereduksi konsentrasi parameter outlet sampai dibawah baku mutu yang distandarkan kecuali untuk parameter miyak/lemak pada perlakuan laju alir tinggi. Pada effluen

  12. The importance of temperature dependent energy gap in the understanding of high temperature thermoelectric properties

    Science.gov (United States)

    Singh, Saurabh; Pandey, Sudhir K.

    2016-10-01

    In this work, we show the importance of temperature dependent energy band gap, E g (T), in understanding the high temperature thermoelectric (TE) properties of material by considering LaCoO3 (LCO) and ZnV2O4 (ZVO) compounds as a case study. For the fix value of band gap, E g , deviation in the values of α has been observed above 360 K and 400 K for LCO and ZVO compounds, respectively. These deviation can be overcomed by consideration of temperature dependent band gap. The change in used value of E g with respect to temperature is ∼4 times larger than that of In As. This large temperature dependence variation in E g can be attributed to decrement in the effective on-site Coulomb interaction due to lattice expansion. At 600 K, the value of ZT for n and p-doped, LCO is ∼0.35 which suggest that it can be used as a potential material for TE device. This work clearly suggest that one should consider the temperature dependent band gap in predicting the high temperature TE properties of insulating materials.

  13. Advanced materials for high-temperature thermoelectric energy conversion

    Science.gov (United States)

    Vining, Cronin B.; Vandersande, Jan W.; Wood, Charles

    1992-01-01

    A number of refractory semiconductors are under study at the Jet Propulsion Laboratory for application in thermal to electric energy conversion for space power. The main thrust of the program is to improve or develop materials of high figure of merit and, therefore, high conversion efficiencies over a broad temperature range. Materials currently under investigation are represented by silicon-germanium alloys, lanthanum telluride, and boron carbide. The thermoelectric properties of each of these materials, and prospects for their further improvements, are discussed. Continued progress in thermoelectric materials technology can be expected to yield reliable space power systems with double to triple the efficiency of current state of the art systems.

  14. Thermoelectric energy harvesting from small ambient temperature transients

    Energy Technology Data Exchange (ETDEWEB)

    Moser, Andre

    2012-07-01

    Wireless sensor networks (WSNs) represent a key technology, used, for instance, in structural health monitoring, building automation systems, or traffic surveillance. Supplying power to a network of spatially distributed sensor nodes, especially at remote locations, is a large challenge: power grids are reliable but costly to install, whereas batteries provide a high flexibility in the installation but have a limited lifetime. This dilemma can be overcome by micro energy harvesting which offers both: reliability and flexibility. Micro energy harvesters are able to convert low grade ambient energy into useful electrical energy and thus provide power for wireless sensor networks or other electronic devices - in-situ, off-grid, and with an almost unlimited lifetime. Thermal energy is an omnipresent source of ambient energy: The day-night-cycle of the sun causes a temperature variation in the ambient air as well as arbitrary solids (soil, building walls, etc.). Unlike the air, solids have a large thermal inertia which dampens the temperature variation. This physical process leads to a temperature difference {Delta}T = T{sub air} - T{sub solid} between air and solid that can be converted directly into electrical energy by a thermoelectric generator (TEG). Thermal and electrical interfaces are necessary to connect the TEG to the thermal energy source (T{sub air}, T{sub solid}) and the electrical load (WSN). Reliable operation of the WSN may only be ensured if the harvester provides sufficient electrical energy, i.e. operates at its maximum power point. The goal of this thesis is to study, design, and test thermoelectric harvesters generating electrical energy from small ambient temperature transients in order to self-sufficiently power a WSN. Current research into thermoelectric energy harvesting, especially analytical modeling and application in the field are treated insufficiently. Therefore, a time-dependent analytical model of the harvester's output power is set

  15. Experimental temperature measurements for the energy amplifier test

    Energy Technology Data Exchange (ETDEWEB)

    Calero, J. [Centro de Estudios y Experimentacion de Obras Publicas (CEDEX), Madrid (Spain); Cennini, P. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland); Gallego, E. [Universidad Politecnica de Madrid (UPM), E-28040 Madrid (Spain); Galvez, J. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland)]|[Universidad Autonoma de Madrid (UAM), E-28049 Madrid (Spain); Garcia Tabares, L. [Centro de Estudios y Experimentacion de Obras Publicas (CEDEX), Madrid (Spain); Gonzalez, E. [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas (CIEMAT), E-28040 Madrid (Spain); Jaren, J. [Universidad Autonoma de Madrid (UAM), E-28049 Madrid (Spain); Lopez, C. [Universidad Autonoma de Madrid (UAM), E-28049 Madrid (Spain); Lorente, A. [Universidad Politecnica de Madrid (UPM), E-28040 Madrid (Spain); Martinez Val, J.M. [Universidad Politecnica de Madrid (UPM), E-28040 Madrid (Spain); Oropesa, J. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland); Rubbia, C. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland); Rubio, J.A. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland)]|[Centro de Investigaciones Energeticas Medioambientales y Tecnologicas (CIEMAT), E-28040 Madrid (Spain); Saldana, F. [European Laboratory for Particle Physics, CH-1211 Geneva 23 (Switzerland); Tamarit, J. [Centro de Estudios y Experimentacion de Obras Publicas (CEDEX), Madrid (Spain); Vieira, S. [Universidad Autonoma de Madrid (UAM), E-28049 Madrid (Spain)

    1996-06-21

    A uranium thermometer has been designed and built in order to make local power measurements in the first energy amplifier test (FEAT). Due to the experimental conditions power measurements of tens to hundreds of nW were required, implying a sensitivity in the temperature change measurements of the order of 1 mK. A uranium thermometer accurate enough to match that sensitivity has been built. The thermometer is able to determine the absolute energetic gain obtained in a tiny subcritical uranium assembly exposed to a proton beam of kinetic energies between 600 MeV and 2.75 GeV. In addition, the thermometer measurements have provided information about the spatial power distribution and the shape of the neutron spallation cascade. (orig.).

  16. Refractory materials for high-temperature thermoelectric energy conversion

    Science.gov (United States)

    Wood, C.; Emin, D.

    1984-01-01

    Theoretical work of two decades ago adequately explained the transport behavior and effectively guided the development of thermoelectric materials of high conversion efficiencies of conventional semiconductors (e.g., SiGe alloys). The more significant contributions involved the estimaiation of optimum doping concentrations, the reduction of thermal conductivity by solid solution doping and the development of a variety of materials with ZT approx. 1 in the temperature range 300 K to 1200 K. ZT approx. 1 is not a theoretical limitation although, experimentally, values in excess of one were not achieved. Work has continued with emphasis on higher temperature energy conversion. A number of promising materials have been discovered in which it appears that ZT 1 is realizable. These materials are divided into two classes: (1) the rare-earth chalcogenides which behave as itinerant highly-degenerate n-type semiconductors at room-temperature, and (2) the boron-rich borides, which exhibit p-type small-polaronic hopping conductivity.

  17. Refractory materials for high-temperature thermoelectric energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Wood, C.; Emin, D.

    1983-01-01

    Theoretical work of two decades ago adequately explained the transport behavior and effectively guided the development of thermoelectric materials of high conversion efficiencies of conventional semiconductors (e.g., SiGe alloys). The more significant contributions involved the estimation of optimum doping concentrations, the reduction of thermal conductivity by solid solution doping and the development of a variety of materials with ZT approx. 1 in the temperature range 300 K to 1200 K. It was also shown that ZT approx. 1 is not a theoretical limitation although, experimentally, values in excess of one were not achieved. Work has continued with emphasis on higher temperature energy conversion. A number of promising materials have been discovered in which it appears that ZT > 1 is realizable. These materials can be divided into two classes: (i) the rare-earth chalcogenides, which behave as itinerant highly-degenerate n-type semiconductors at room-temperature, and (ii) the boron-rich borides, which exhibit p-type small-polaronic hopping conductivity.

  18. The Temperature Condition of the Plate with Temperature-Dependent Thermal Conductivity and Energy Release

    Directory of Open Access Journals (Sweden)

    V. S. Zarubin

    2016-01-01

    Full Text Available The temperature state of a solid body, in addition to the conditions of its heat exchange with the environment, can greatly depend on the heat release (or heat absorption processes within the body volume. Among the possible causes of these processes should be noted such as a power release in the fuel elements of nuclear reactors, exothermic or endothermic chemical reactions in the solid body material, which respectively involve heat release or absorbtion, heat transfer of a part of the electric power in the current-carrying conductors (so-called Joule’s heat or the energy radiation penetrating into the body of a semitransparent material, etc. The volume power release characterizes an intensity of these processes.The extensive list of references to the theory of heat conductivity of solids offers solutions to problems to determine a stationary (steady over time and non-stationary temperature state of the solids (as a rule, of the canonical form, which act as the sources of volume power release. Thus, in general case, a possibility for changing power release according to the body volume and in solving the nonstationary problems also a possible dependence of this value on the time are taken into consideration.However, in real conditions the volume power release often also depends on the local temperature, and such dependence can be nonlinear. For example, with chemical reactions the intensity of heat release or absorption is in proportion to their rate, which, in turn, is sensitive to the temperature value, and a dependence on the temperature is exponential. A further factor that in such cases makes the analysis of the solid temperature state complicated, is dependence on the temperature and the thermal conductivity of this body material, especially when temperature distribution therein  is significantly non-uniform. Taking into account the influence of these factors requires the mathematical modeling methods, which allow us to build an adequate

  19. Lowering the cost of large-scale energy storage: High temperature adiabatic compressed air energy storage

    Directory of Open Access Journals (Sweden)

    B. Cárdenas

    2017-06-01

    Full Text Available Compressed air energy storage is an energy storage technology with strong potential to play a significant role in balancing energy on transmission networks, owing to its use of mature technologies and low cost per unit of storage capacity. Adiabatic compressed air energy storage (A-CAES systems typically compress air from ambient temperature in the charge phase and expand the air back to ambient temperature in the discharge phase. This papers explores the use of an innovative operating scheme for an A-CAES system aimed at lowering the total cost of the system for a given exergy storage capacity. The configuration proposed considers preheating of the air before compression which increases the fraction of the total exergy that is stored in the form of high-grade heat in comparison to existing designs in which the main exergy storage medium is the compressed air itself. Storing a high fraction of the total exergy as heat allows reducing the capacity of costly pressure stores in the system and replacing it with cheaper thermal energy stores. Additionally, a configuration that integrates a system based on the aforementioned concept with solar thermal power or low-medium grade waste heat is introduced and thoroughly discussed.

  20. Integration of body temperature into the analysis of energy expenditure in the mouse

    OpenAIRE

    Abreu-Vieira, Gustavo; Xiao, Cuiying; Gavrilova, Oksana; Reitman, Marc L.

    2015-01-01

    Objectives: We quantified the effect of environmental temperature on mouse energy homeostasis and body temperature. Methods: The effect of environmental temperature (4–33 °C) on body temperature, energy expenditure, physical activity, and food intake in various mice (chow diet, high-fat diet, Brs3-/y, lipodystrophic) was measured using continuous monitoring. Results: Body temperature depended most on circadian phase and physical activity, but also on environmental temperature. The amoun...

  1. PENGARUH KONSENTRASI ZrO2 TERHADAP KORELASI PERPINDAHAN PANAS NANOFLUIDA AIR-ZrO2 UNTUK PENDINGIN REAKTOR

    Directory of Open Access Journals (Sweden)

    K.A. Sudjatmi

    2015-03-01

    Full Text Available Sejalan dengan perkembangan konsep keselamatan pasif pada sistem keselamatan PLTN, maka sistem perpindahan panas konveksi alam memegang peranan penting. Pemakaian nanofluid sebagai fluida pendingin pada sistem keselamatan nuklir dapat digunakan pada Sistem Pendingin Teras Darurat dan Sistem Pendingin Pengungkung Luar Reaktor. Beberapa peneliti telah melakukan studi desain konseptual aplikasi nanofluid untuk meningkatkan keselamatan AP1000 dan sistem pendingin teras darurat pada reaktor daya eksperimen. Penerapan nanofluida juga mulai dikembangkan melalui hasil penelitian perpindahan panas konveksi alamiah pada sub-buluh dengan nanofluida sebagai fluida kerjanya sangat dibutuhkan. Penelitian ini bertujuan untuk menentukan pengaruh perubahan konsentrasi ZrO2 terhadap korelasi perpindahan panas konveksi alamiah dengan pendekatan eksperimental. Data eksperimental yang diperoleh digunakan untuk mengembangkan korelasi umum empirik perpindahan panas konveksi alamiah. Metode penelitian dengan menggunakan alat uji sub-buluh vertikal dengan geometri segitiga dan segiempat menggunakan air dan nanofluida air-ZrO2 sebagai fluida kerjanya. Konsentrasi nanopartikel dalam larutan yang digunakan sebesar 0,05 %, 0,10% dan 0,15 % dalam persen berat. Hasil penelitian menunjukan bahwa untuk bilangan Rayleigh yang sama, kemampuan pemindahan kalor oleh nanofluida air-ZrO2 lebih baik dari pada pemindahan kalor oleh air. Namun peningkatan konsentrasi nanofluida tidak selalu mendapatkan kemampuan pemindahan kalor yang lebih baik. Kata kunci: nanofluida air-ZrO2, konveksi alamiah, sub-buluh segitiga, sub-buluh segi segiempat   In line with the development of the passive safety concept for the safety systems of nuclear power plants, the natural convection heat transfer system plays an important role. The nanofluid as coolant fluid on nuclear safety system can be used in Emergency core cooling system and in reactor coolant system confinement. Several researchers have

  2. High incubation temperatures enhance mitochondrial energy metabolism in reptile embryos.

    Science.gov (United States)

    Sun, Bao-Jun; Li, Teng; Gao, Jing; Ma, Liang; Du, Wei-Guo

    2015-03-09

    Developmental rate increases exponentially with increasing temperature in ectothermic animals, but the biochemical basis underlying this thermal dependence is largely unexplored. We measured mitochondrial respiration and metabolic enzyme activities of turtle embryos (Pelodiscus sinensis) incubated at different temperatures to identify the metabolic basis of the rapid development occurring at high temperatures in reptile embryos. Developmental rate increased with increasing incubation temperatures in the embryos of P. sinensis. Correspondingly, in addition to the thermal dependence of mitochondrial respiration and metabolic enzyme activities, high-temperature incubation further enhanced mitochondrial respiration and COX activities in the embryos. This suggests that embryos may adjust mitochondrial respiration and metabolic enzyme activities in response to developmental temperature to achieve high developmental rates at high temperatures. Our study highlights the importance of biochemical investigations in understanding the proximate mechanisms by which temperature affects embryonic development.

  3. UNJUK KERJA REAKTOR PLASMA DIELECTRIC BARRIER DISCHARGE UNTUK PRODUKSI BIODIESEL DARI MINYAK KELAPA SAWIT

    Directory of Open Access Journals (Sweden)

    Ardian Dwi Yudhistira

    2013-10-01

    Full Text Available Biodiesel is one of alternative renewable energy source to substitute diesel fuel. Various biodiesel productionprocesses through transesterification reaction with a variety of catalysts have been developed by previousresearcher. This process still has the disadvantage of a long reaction time, and high energy need. DielectricBarrier Discharge (DBD plasma electro-catalysis may become a solution to overcome the drawbacks in theconventional transesterification process. This process only needs a short time reaction and low energy process.The purpose of this study was to assess the performance of DBD plasma rector in making biodiesel such as: theeffect of high voltage electric value, electrodes gap, mole ratio of methanol / oil, and reaction time. TheResearch method was using GC-MS (Gas Cromatography-Mass Spectrofotometry and FTIR (FourierTransform Infrared Spectrofotometry and then it will be analysed the change of chemical bond betweenreactant and product. So, the reaction mechanism can be predicted. Biodiesel is produced using methanol andpalm oil as reactants and DBD plasma used as reactor in batch system. Then, reactants contacted by highvoltage electric. From the results of this research can be concluded that the reaction mechanism occurs in theprocess is the reaction mechanism of cracking, the higher of electric voltage and the longer of reaction time leadto increasing of product yield. The more of mole ratio of methanol / oil and widening the gap between theelectrodes lead to decreased product yield. From this research, product yield maksimum is 89,8% in the variableof rasio mol metanol/palm oil 3:1, voltage 10 kV, electrode gap 1,5 cm, and reaction time 30 seconds.

  4. PENJERAPAN GAS CO HASIL PEMBAKARAN SAMPAH MENGGUNAKAN SORBENT TERMODIFIKASI DALAM REAKTOR FIXED BED

    Directory of Open Access Journals (Sweden)

    Mariana Mariana

    2013-11-01

    Full Text Available ADSORPTION OF CO FROM WASTE COMBUSTION USING MODIFIED SORBENT IN A FIXED BED REACTOR. Gases produced by garbage burning consist of dangerous gases such as CO, SO2 and other gases. Technology for reducing dangerous gases from incinerator outlet can be done by using a dry or wet process. The dry process is more economical process because of simple process, easy maintenance and no liquid waste as product. However, the weakness of the dry process is low absorption conversion and low gas removal efficiency. One way to overcome these problems is to use sorbent which has high reactivity. An inexpensive sorbent that commonly used is Ca(OH2. The aim of this research was to increase the reactivity of Ca(OH2 sorbent by using diatomaceous earth and compost as a source of silica and biosorbent, respectively. Diatomaceous earth contains CaO, SiO2 and Al2O3 and compost contains bacteria as a biosorbent that can convert CO to CO2 and CH4. The reaction between SiO2 and Ca(OH2 would form calcium silicate hydrate (CaO.SiO2.2H2O that has a high porosity and reactivity. The results showed that the reactivity of Ca(OH2 sorbent increased by addition of diatomaceous earth and compost. The results also showed that the sorption of CO gas increases with increasing of height of sorbent bed and temperature. The highest CO gas sorption was obtained at temperature of 150oC and sorbent bed height of 6 cm using the modified sorbent with Ca(OH2/DE/compost ratio of 3:1:1. Gas hasil pembakaran sampah terdiri dari gas-gas yang berbahaya seperti CO, SO2 dan lain sebagainya. Teknologi penghilangan gas-gas tersebut dapat dilakukan dengan menggunakan proses kering maupun proses basah. Penghilangan dengan proses kering lebih ekonomis karena sederhana, mudah pemeliharaan dan tidak menghasilkan limbah cair. Namun demikian, kelemahan proses kering adalah konversi absorpsi rendah dan efisiensi penyisihan  gas relatif kecil. Salah satu cara mengatasi masalah tersebut di atas adalah dengan

  5. Comparison of Low-temperature District Heating Concepts in a Long-Term Energy System Perspective

    DEFF Research Database (Denmark)

    Lund, Rasmus Søgaard; Østergaard, Dorte Skaarup; Yang, Xiaochen

    2017-01-01

    renewable energy systems. This study compares three alternative concepts for DH temperature level: Low temperature (55/25 °C), Ultra-low temperature with electric boosting (45/25 °C), and Ultra-low temperature with heat pump boosting (35/20 °C) taking into account the grid losses, production efficiencies...... and building requirements. The scenarios are modelled and analysed in the analysis tool EnergyPLAN and compared on primary energy supply and socioeconomic costs. The results show that the low temperature solution (55/25°C) has the lowest costs, reducing the total costs by about 100 M€/year in 2050....

  6. Wave energy transmission apparatus for high-temperature environments

    Science.gov (United States)

    Buckley, John D. (Inventor); Edwards, William C. (Inventor); Kelliher, Warren C. (Inventor); Carlberg, Ingrid A. (Inventor)

    2010-01-01

    A wave energy transmission apparatus has a conduit made from a refractory oxide. A transparent, refractory ceramic window is coupled to the conduit. Wave energy passing through the window enters the conduit.

  7. Thermodynamics of the living organisms. Allometric relationship between the total metabolic energy, chemical energy and body temperature in mammals

    Science.gov (United States)

    Atanasov, Atanas Todorov

    2017-11-01

    The study present relationship between the total metabolic energy (ETME(c), J) derived as a function of body chemical energy (Gchem, J) and absolute temperature (Tb, K) in mammals: ETME(c) =Gchem (Tb/Tn). In formula the temperature Tn =2.73K appears normalization temperature. The calculated total metabolic energy ETME(c) differs negligible from the total metabolic energy ETME(J), received as a product between the basal metabolic rate (Pm, J/s) and the lifespan (Tls, s) of mammals: ETME = Pm×Tls. The physical nature and biological mean of the normalization temperature (Tn, K) is unclear. It is made the hypothesis that the kTn energy (where k= 1.3806×10-23 J/K -Boltzmann constant) presents energy of excitation states (modes) in biomolecules and body structures that could be in equilibrium with chemical energy accumulated in body. This means that the accumulated chemical energy allows trough all body molecules and structures to propagate excitations states with kTn energy with wavelength in the rage of width of biological membranes. The accumulated in biomolecules chemical energy maintains spread of the excited states through biomolecules without loss of energy.

  8. Life Cycle Assessment of High Temperature Geothermal Energy Systems

    OpenAIRE

    Marchand, Mathilde; Blanc, Isabelle; Marquand, Aline; Beylot, Antoine; Bezelgues-Courtade, Sophie; Traineau, Hervé

    2015-01-01

    International audience; European and French regulations state that 50% of the energy mix in the French Caribbean should be sourced from renewable energies by 2020. Because of the volcanic conditions of the French Caribbean islands, geothermal energy would seem to be a very favorable solution to reach this ambitious objective, as, unlike other renewable sources, it is continuous and weather independent. According to the Intergovernmental Panel on Climate Change (IPCC), geothermal energy source...

  9. South Africa's geothermal energy hotspots inferred from subsurface temperature and geology

    OpenAIRE

    Taufeeq Dhansay; Chiedza Musekiwa; Thakane Ntholi; Luc Chevallier; Doug I.Cole; de Wit, Maarten J.

    2017-01-01

    South Africa intends to mitigate its carbon emissions by developing renewable energy from solar, wind and hydro, and investigating alternative energy sources such as natural gas and nuclear. Low-enthalpy geothermal energy is becoming increasingly popular around the world, largely as a result of technological advances that have enabled energy to be harnessed from relatively low temperature sources. However, geothermal energy does not form part of South Africa’s future renewable energy scenario...

  10. KARAKTERISTIK BIODIESEL DARI MINYAK BIJI RANDU (CEIBA PENTANDRA PADA REAKTOR BATCH BERPENGADUK BERTEKANAN MENGGUNAKAN KATALIS KOH

    Directory of Open Access Journals (Sweden)

    Nove Kartika Erliyanti

    2016-08-01

    Full Text Available Biodiesel is fuel from plant oils that has been converted into methyil ester with transesterification process. The research was aimed at investigating the influence of KOH concentration and reaction time on the characteristics (density and viscosity biodiesel at a pressure of 4 bar. The process of making biodiesel in a stirred batch reactor is pressurized, purged nitrogen, and the temperature operation of 60°C. The kapok seed oil used as raw material was 1000, methanol, and KOH (concentration of 0.5; 1.0; 1.5; and 2% oil by weight were mixed and put into a reactor with a reaction time of 0.25; 0.50; 1.00; and 1.50 hours. Products were analyzed according to ASTM standard. KOH concentration and reaction time has a significantly affected with respect to the density and viscosity of biodiesel. Biodiesel produced in compliance with the ASTM standard. The highest density and viscosity resulting in 0.5% KOH concentration and reaction time of 0.25 hours is equal to 0.8918 g / cm3 and 4.989 cSt.

  11. Synchronous temperature rate control for refrigeration with reduced energy consumption

    Science.gov (United States)

    Gomes, Alberto Regio; Keres, Stephen L.; Kuehl, Steven J.; Litch, Andrew D.; Richmond, Peter J.; Wu, Guolian

    2015-09-22

    Methods of operation for refrigerator appliance configurations with a controller, a condenser, at least one evaporator, a compressor, and two refrigeration compartments. The configuration may be equipped with a variable-speed or variable-capacity compressor, variable speed evaporator or compartment fans, a damper, and/or a dual-temperature evaporator with a valve system to control flow of refrigerant through one or more pressure reduction devices. The methods may include synchronizing alternating cycles of cooling each compartment to a temperature approximately equal to the compartment set point temperature by operation of the compressor, fans, damper and/or valve system. The methods may also include controlling the cooling rate in one or both compartments. Refrigeration compartment cooling may begin at an interval before or after when the freezer compartment reaches its lower threshold temperature. Freezer compartment cooling may begin at an interval before or after when the freezer compartment reaches its upper threshold temperature.

  12. Synchronous temperature rate control for refrigeration with reduced energy consumption

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, Alberto Regio; Keres, Stephen L.; Kuehl, Steven J.; Litch, Andrew D.; Richmond, Peter J.; Wu, Guolian

    2017-11-07

    Methods of operation for refrigerator appliance configurations with a controller, a condenser, at least one evaporator, a compressor, and two refrigeration compartments. The configuration may be equipped with a variable-speed or variable-capacity compressor, variable speed evaporator or compartment fans, a damper, and/or a dual-temperature evaporator with a valve system to control flow of refrigerant through one or more pressure reduction devices. The methods may include synchronizing alternating cycles of cooling each compartment to a temperature approximately equal to the compartment set point temperature by operation of the compressor, fans, damper and/or valve system. The methods may also include controlling the cooling rate in one or both compartments. Refrigeration compartment cooling may begin at an interval before or after when the freezer compartment reaches its lower threshold temperature. Freezer compartment cooling may begin at an interval before or after when the freezer compartment reaches its upper threshold temperature.

  13. A novel theoretical model for the temperature dependence of band gap energy in semiconductors

    Science.gov (United States)

    Geng, Peiji; Li, Weiguo; Zhang, Xianhe; Zhang, Xuyao; Deng, Yong; Kou, Haibo

    2017-10-01

    We report a novel theoretical model without any fitting parameters for the temperature dependence of band gap energy in semiconductors. This model relates the band gap energy at the elevated temperature to that at the arbitrary reference temperature. As examples, the band gap energies of Si, Ge, AlN, GaN, InP, InAs, ZnO, ZnS, ZnSe and GaAs at temperatures below 400 K are calculated and are in good agreement with the experimental results. Meanwhile, the band gap energies at high temperatures (T  >  400 K) are predicted, which are greater than the experimental results, and the reasonable analysis is carried out as well. Under low temperatures, the effect of lattice expansion on the band gap energy is very small, but it has much influence on the band gap energy at high temperatures. Therefore, it is necessary to consider the effect of lattice expansion at high temperatures, and the method considering the effect of lattice expansion has also been given. The model has distinct advantages compared with the widely quoted Varshni’s semi-empirical equation from the aspect of modeling, physical meaning and application. The study provides a convenient method to determine the band gap energy under different temperatures.

  14. Technique for the estimation of surface temperatures from embedded temperature sensing for rapid, high energy surface deposition.

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, Tyson R.; Schunk, Peter Randall; Roberts, Scott Alan

    2014-07-01

    Temperature histories on the surface of a body that has been subjected to a rapid, highenergy surface deposition process can be di cult to determine, especially if it is impossible to directly observe the surface or attach a temperature sensor to it. In this report, we explore two methods for estimating the temperature history of the surface through the use of a sensor embedded within the body very near to the surface. First, the maximum sensor temperature is directly correlated with the peak surface temperature. However, it is observed that the sensor data is both delayed in time and greatly attenuated in magnitude, making this approach unfeasible. Secondly, we propose an algorithm that involves tting the solution to a one-dimensional instantaneous energy solution problem to both the sensor data and to the results of a one-dimensional CVFEM code. This algorithm is shown to be able to estimate the surface temperature 20 C.

  15. A new method to determine the energy saving night temperature for vegetative growth of Phalaenopsis

    NARCIS (Netherlands)

    Pollet, B.; Kromwijk, J.A.M.; Vanhaecke, L.; Dambre, P.; Labeke, M.C.; Marcelis, L.F.M.; Steppe, K.

    2011-01-01

    Knowledge of the energy saving night temperature (i.e. a relatively cool night temperature without affecting photosynthetic activity and physiology) and a better understanding of low night temperature effects on the photosynthetic physiology of Phalaenopsis would improve their production in terms of

  16. Energy Efficiency of Low-Temperature Deaeration of Makeup Water for a District Heating System

    Energy Technology Data Exchange (ETDEWEB)

    Sharapov, V. I., E-mail: vlad-sharapov2008@yandex.ru; Kudryavtseva, E. V. [Ulyanovsk State Technical University (Russian Federation)

    2016-07-15

    It is shown that the temperature of makeup water in district heating systems has a strong effect on the energy efficiency of turbines of thermal power plants. A low-temperature deaeration process that considerably improves the energy efficiency of thermal power plants is developed. The desorbing agent is the gas supplied to the burners of the boiler. The energy efficiency of the process for a typical unit of thermal power plant is assessed.

  17. Wide Temperature Range Hybrid Energy Storage Device Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal concerns the fabrication of a hybrid battery capacitor (HBC) using Eltron's knowledge gained in battery and capacitor research. Energy storage systems...

  18. High temperature corrosion issues in energy-related systems

    Directory of Open Access Journals (Sweden)

    Stringer John

    2004-01-01

    Full Text Available The large majority of electric power that is generated world-wide involves heat engines of one kind or another. The significant exceptions are hydroelectric generation; wind; and photovoltaics. The thermal sources for the heat engines include: fossil fuels, nuclear fission, biomass, geothermal sources, and solar radiation. There has been a progressive move to higher overall cycle efficiencies for at least one hundred years, and in the case of fossil fuels this has accelerated recently in part because of concerns about greenhouse gas emissions, notably CO2. For a heat engine, the overall efficiency is closely related to the difference between the highest temperature in the cycle and the lowest temperature. In most cases, this has resulted in an increase in the high temperature, and this in turn has led to increasing demands on the materials of construction used in the high temperature end of the systems. One of the issues is the chemical degradation because of reactions between the materials of construction and the environments to which they are exposed: this is high temperature corrosion. This paper will describe the issues for a range of current heat engines.

  19. APLIKASI TEKNIK AAN DI REAKTOR RSG-GAS PADA PENENTUAN UNSUR ESENSIAL DAN TOKSIK DI DALAM IKAN DAN PAKAN IKAN

    Directory of Open Access Journals (Sweden)

    Saeful Yusuf

    2015-03-01

    Full Text Available Pada makalah ini diuraikan tentang aplikasi teknik AAN (Analisis Aktivasi Neutron dalam penentuan konsentrasi unsur-unsur esensial dan cemaran yang terkandung di dalam beberapa spesies ikan dan pakan ikan. Unsur-unsur esensial yang terkandung dalam pakan ikan buatan juga dianalisis untuk mengetahui pengaruhnya terhadap ikan. Penentuan unsur menggunakan teknik AAN dengan metode perbandingan dan metode k0-AAN. Sampel diiradiasi di reaktor RSG-GAS yang memiliki fluks neutron thermal 5 x 1013 n.cm-2.s-1 pada daya 15 MW. Hasil penelitian menunjukkan bahwa 12 unsur di dalam 11 spesies ikan air laut dan air tawar telah ditentukan yaitu As, Br, Cr, Co, Cs, Fe, Hg, K, Na, Rb, Se and Zn. Konsentrasi cemaran As didalam ikan laut sudah melampaui batas maksimum 1 mg/kg, sedangkan konsentrasi cemaran Hg masih dibawah batas maksimum 0,5 mg/kg, baik untuk ikan laut maupun ikan air tawar. Unsur K dan Na merupakan unsur makroesensial sedangkan unsur Cr, Co, Fe, Se and Zn adalah termasuk unsur mikroesensial. Secara umum ditunjukkan bahwa kandungan mineral didalam ikan laut lebih tinggi konsentrasinya dibandingkan ikan air tawar. Br, Cs dan Rb merupakan unsur-unsur non esensial yang teridentifikasi dalam semua ikan yang dianalisis. Penelitian terhadap pakan ikan air tawar menunjukkan bahwa semua unsur yang teridentifikasi juga terdapat di dalam ikan laut dan ikan air tawar. Hal ini menunjukkan bahwa pakan ikan berkontribusi terhadap konsentrasi unsur di dalam ikan air tawar. Kata kunci : Analisis aktivasi neutron, unsur esensial, unsur cemaran, ikan, pakan ikan   This paper reported on the application of NAA (Neutron Activation Analysis Technique in the determination of the concentration of the essential and toxic elements in some species of fish and fish feed. Determination of elements using instrumental NAA technique with comparison and k0-INAA methods. Samples were irradiated in the RSG-GAS which has a thermal neutron flux  5.0E +13 ncm-2s-1. The results

  20. Performance of low-temperature district heating for low-energy houses

    DEFF Research Database (Denmark)

    Brand, Marek; Dalla Rosa, Alessandro; Svendsen, Svend

    2010-01-01

    houses, which was previously developed and reported in the project “Development and demonstration of low-energy district heating for low energy housing” [EFP, 2007]. Two different concepts of low energy district heating substations are tested, and measurements of their performance aim to document......A Low Energy District Heating (LEDH) network supplying district heating water with temperature 50°C was built in Lærkehaven-Lystrup, Denmark, as a part of the ongoing “Energy Technology Development and Demonstration Programme” [EUDP, 2008] focused on “CO2-reduction in low energy buildings...... and communities by implementation of low temperature district heating systems”. The network supplies 40 detached Low Energy Houses built in accordance with the requirements of the Danish low energy class 1. The project aims to test and evaluate in real conditions the concept of LEDH for the supply of low energy...

  1. Temperature Effects on Information Capacity and Energy Efficiency of Hodgkin-Huxley Neuron

    CERN Document Server

    Wang, Long-Fei; Liu, Xiao-Zhi; Song, Ya-lei; Yu, Lian-Chun

    2015-01-01

    Recent experimental and theoretical studies show that energy efficiency, which measures the amount of information processed by a neuron with per unit of energy consumption, plays an important role in the evolution of neural systems. Here, we calculated the information rates and energy efficiencies of the Hodgkin-Huxley (HH) neuron model at different temperatures in a noisy environment. We found that both the information rate and energy efficiency are maximized by certain temperatures. Though the information rate and energy efficiency cannot be maximized simultaneously, the neuron holds a high information processing capacity at the temperature corresponding to maximal energy efficiency. Our results support the idea that the energy efficiency is a selective pressure that influences the evolution of nervous systems.

  2. Integration of body temperature into the analysis of energy expenditure in the mouse.

    Science.gov (United States)

    Abreu-Vieira, Gustavo; Xiao, Cuiying; Gavrilova, Oksana; Reitman, Marc L

    2015-06-01

    We quantified the effect of environmental temperature on mouse energy homeostasis and body temperature. The effect of environmental temperature (4-33 °C) on body temperature, energy expenditure, physical activity, and food intake in various mice (chow diet, high-fat diet, Brs3 (-/y) , lipodystrophic) was measured using continuous monitoring. Body temperature depended most on circadian phase and physical activity, but also on environmental temperature. The amounts of energy expenditure due to basal metabolic rate (calculated via a novel method), thermic effect of food, physical activity, and cold-induced thermogenesis were determined as a function of environmental temperature. The measured resting defended body temperature matched that calculated from the energy expenditure using Fourier's law of heat conduction. Mice defended a higher body temperature during physical activity. The cost of the warmer body temperature during the active phase is 4-16% of total daily energy expenditure. Parameters measured in diet-induced obese and Brs3 (-/y) mice were similar to controls. The high post-mortem heat conductance demonstrates that most insulation in mice is via physiological mechanisms. At 22 °C, cold-induced thermogenesis is ∼120% of basal metabolic rate. The higher body temperature during physical activity is due to a higher set point, not simply increased heat generation during exercise. Most insulation in mice is via physiological mechanisms, with little from fur or fat. Our analysis suggests that the definition of the upper limit of the thermoneutral zone should be re-considered. Measuring body temperature informs interpretation of energy expenditure data and improves the predictiveness and utility of the mouse to model human energy homeostasis.

  3. Advanced energy analysis of high temperature fuel cell systems

    NARCIS (Netherlands)

    Kouffeld, R.W.J.; Veringa, H.J.; De Groot, A.

    In this thesis the performance of high temperature fuel cell systems is studied using a new method of exergy analysis. The thesis consists of three parts: ⢠In the first part a new analysis method is developed, which not only considers the total exergy losses in a unit operation, but which

  4. Advanced energy analysis of high temperature fuel cell systems

    NARCIS (Netherlands)

    De Groot, A.

    2004-01-01

    In this thesis the performance of high temperature fuel cell systems is studied using a new method of exergy analysis. The thesis consists of three parts: ⢠In the first part a new analysis method is developed, which not only considers the total exergy losses in a unit operation, but which

  5. Granular temperature measured experimentally in a shear flow by acoustic energy

    Science.gov (United States)

    Taylor, Stephanie; Brodsky, Emily E.

    2017-09-01

    Granular temperature may control high-speed granular flows, yet it is difficult to measure in laboratory experiments. Here we utilize acoustic energy to measure granular temperature in dense shear flows. We show that acoustic energy captures the anticipated behavior of granular temperature as a function of grain size in quartz sand shear flows. We also find that granular temperature (through its proxy acoustic energy) is nearly linearly proportional to inertial number, and dilation is proportional to acoustic energy raised to the power 0.6 ±0.2 . This demonstrates the existence of a relationship between granular temperature and dilation. It is also consistent with previous results on dilation due to externally imposed vibration, thus showing that internally and externally induced vibrations have identical results on granular shear flows.

  6. Corrosion behavior of low energy, high temperature nitrogen ion ...

    Indian Academy of Sciences (India)

    Plasma Physics Research Center, Science and Research Campus of Islamic Azad University, P.O. Box 14665-678, Tehran, Iran; Center of Nuclear Agriculture and Medicine Research, Atomic Energy organization, Karj; Department of Physics, Sharif University, Tehran, Iran; Department of Physics University of Tehran, ...

  7. Ion temperature and hydrodynamic-energy measurements in a Z-pinch plasma at stagnation.

    Science.gov (United States)

    Kroupp, E; Osin, D; Starobinets, A; Fisher, V; Bernshtam, V; Weingarten, L; Maron, Y; Uschmann, I; Förster, E; Fisher, A; Cuneo, M E; Deeney, C; Giuliani, J L

    2011-09-02

    The time history of the local ion kinetic energy in a stagnating plasma was determined from Doppler-dominated line shapes. Using independent determination of the plasma properties for the same plasma region, the data allowed for inferring the time-dependent ion temperature, and for discriminating the temperature from the total ion kinetic energy. It is found that throughout most of the stagnation period the ion thermal energy constitutes a small fraction of the total ion kinetic energy; the latter is dominated by hydrodynamic motion. Both the ion hydrodynamic and thermal energies are observed to decrease to the electron thermal energy by the end of the stagnation period. It is confirmed that the total ion kinetic energy available at the stagnating plasma and the total radiation emitted are in balance, as obtained in our previous experiment. The dissipation time of the hydrodynamic energy thus appears to determine the duration (and power) of the K emission.

  8. Size, shape and temperature dependent surface energy of binary alloy nanoparticles

    Science.gov (United States)

    Jabbareh, Mohammad Amin

    2017-12-01

    Surface energy has an important role in determining the properties of nanoparticles. Even though, extensive research has been done on the surface energy of pure nanoparticles, the surface energy of alloy nanoparticles has not been considered enough. In this work, based on the liquid drop model for surface energy of pure nanoparticles and Butler's equation, a model for size dependent surface energy of alloy nanoparticles has been developed. In addition to size and concentration, the model can describe the effects of shape and temperature on surface energy of alloy nanoparticles. Cu - Ag and Cu - Au systems have been studied as two examples and the results have been compared with other theoretical models and available simulated data. Reasonable agreements between the results were observed. The results show that the decreasing particle size decreases surface energy of alloy nanoparticles but decreasing temperature and shape factor increases the value of surface energy.

  9. CFD Analysis of Energy Separation in Ranque-Hilsch Vortex Tube at Cryogenic Temperature

    Directory of Open Access Journals (Sweden)

    T. Dutta

    2013-01-01

    Full Text Available Study of the energy separation phenomenon in vortex tube (VT at cryogenic temperature (temperature range below 123 K has become important because of the potential application of VT as in-flight air separator in air breathing propulsion. In the present study, a CFD model is used to simulate the energy separation phenomenon in VT with gaseous air at cryogenic temperature as working fluid. Energy separation at cryogenic temperature is found to be considerably less than that obtained at normal atmospheric temperature due to lower values of inlet enthalpy and velocity. Transfer of tangential shear work from inner to outer fluid layers is found to be the cause of energy separation. A parametric sensitivity analysis is carried out in order to optimize the energy separation at cryogenic temperature. Also, rates of energy transfer in the form of sensible heat and shear work in radial and axial directions are calculated to investigate the possible explanation of the variation of the hot and cold outlet temperatures with respect to various geometric and physical input parameters.

  10. HIGH-TEMPERATURE ELECTROLYSIS FOR HYDROGEN PRODUCTION FROM NUCLEAR ENERGY

    Energy Technology Data Exchange (ETDEWEB)

    James E. O& #39; Brien; Carl M. Stoots; J. Stephen Herring; Joseph J. Hartvigsen

    2005-10-01

    An experimental study is under way to assess the performance of solid-oxide cells operating in the steam electrolysis mode for hydrogen production over a temperature range of 800 to 900ºC. Results presented in this paper were obtained from a ten-cell planar electrolysis stack, with an active area of 64 cm2 per cell. The electrolysis cells are electrolyte-supported, with scandia-stabilized zirconia electrolytes (~140 µm thick), nickel-cermet steam/hydrogen electrodes, and manganite air-side electrodes. The metallic interconnect plates are fabricated from ferritic stainless steel. The experiments were performed over a range of steam inlet mole fractions (0.1 - 0.6), gas flow rates (1000 - 4000 sccm), and current densities (0 to 0.38 A/cm2). Steam consumption rates associated with electrolysis were measured directly using inlet and outlet dewpoint instrumentation. Cell operating potentials and cell current were varied using a programmable power supply. Hydrogen production rates up to 90 Normal liters per hour were demonstrated. Values of area-specific resistance and stack internal temperatures are presented as a function of current density. Stack performance is shown to be dependent on inlet steam flow rate.

  11. High Temperature Energy Storage for In Situ Planetary Atmospheric Measurement Technologies Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Development of energy storage capable of operational temperatures of 380:C and 486oC with a specific capacity 200 Wh/kg for use as a power source on the Venusian...

  12. Experimental study of energy performance in low-temperature hydronic heating systems

    DEFF Research Database (Denmark)

    Hesaraki, Arefeh; Bourdakis, Eleftherios; Ploskić, Adnan

    2015-01-01

    Energy consumption, thermal environment and environmental impacts were analytically and experimentally studied for different types of heat emitters. The heat emitters studied were conventional radiator, ventilation radiator, and floor heating with medium-, low-, and very-low-temperature supply, r...

  13. Effect of Two Temperatures on Reflection Coefficient in Micropolar Thermoelastic with and without Energy Dissipation Media

    Directory of Open Access Journals (Sweden)

    Rajneesh Kumar

    2014-01-01

    Full Text Available The reflection of plane waves at the free surface of thermally conducting micropolar elastic medium with two temperatures is studied. The theory of thermoelasticity with and without energy dissipation is used to investigate the problem. The expressions for amplitudes ratios of reflected waves at different angles of incident wave are obtained. Dissipation of energy and two-temperature effects on these amplitude ratios with angle of incidence are depicted graphically. Some special and particular cases are also deduced.

  14. The analysis of energy efficiency in water electrolysis under high temperature and high pressure

    Science.gov (United States)

    Hourng, L. W.; Tsai, T. T.; Lin, M. Y.

    2017-11-01

    This paper aims to analyze the energy efficiency of water electrolysis under high pressure and high temperature conditions. The effects of temperature and pressure on four different kinds of reaction mechanisms, namely, reversible voltage, activation polarization, ohmic polarization, and concentration polarization, are investigated in details. Results show that the ohmic and concentration over-potentials are increased as temperature is increased, however, the reversible and activation over-potentials are decreased as temperature is increased. Therefore, the net efficiency is enhanced as temperature is increased. The efficiency of water electrolysis at 350°C/100 bars is increased about 17%, compared with that at 80°C/1bar.

  15. Occupant responses and energy use in buildings with moderately drifting temperatures

    DEFF Research Database (Denmark)

    Toftum, Jørn; Olesen, Bjarne W.; Kolarik, Jakub

    research was initiated in 2005 knowledge was lacking on how the intensity of building related symptoms, the perception of air quality and the performance of office work were affected by exposure to non-steady-state temperatures. ASHRAE Standard 55 (2004) provides recommendations for maximum rates...... of temperature change to avoid discomfort, but these recommendations are based mostly on engineering judgment and to some extent on results of earlier thermal comfort research. New approaches to reducing the consumption of energy for climate conditioning in buildings are often associated with indoor temperatures...... of the recommendations on non-steady-state temperatures as stated in Standard 55 and to evaluate how Sick Building Syndrome symptoms, perceived air quality and performance are affected by such changing temperatures. In addition, the feasibility of non-steady-state temperatures as a means of energy savings and reduction...

  16. Refractory semiconductors for high temperature thermoelectric energy conversion

    Science.gov (United States)

    Wood, Charles

    Thermoelectric energy conversion utilizing nuclear heat sources has been employed for several decades to generate power for deep space probes. In the past, lead telluride and, more recently, silicon-germanium alloys have been the prime choices as thermoelectric materials for this application. Currently, a number of refractory semiconductors are under investigation at the Jet Propulsion Laboratory in order to produce power sources of higher conversion efficiency and, thus, lower mass per unit of power output. Included among these materials are improved Si-Ge alloys, rare earth compounds and boron-rich borides. The criteria used to select thermoelectric materials, in general, and the above materials, in particular, will be discussed. The current state of the art and the accomplishments to date in thermoelectric materials research will be reviewed.

  17. Analysis of the Potential of Low-Temperature Heat Pump Energy Sources

    Directory of Open Access Journals (Sweden)

    Pavel Neuberger

    2017-11-01

    Full Text Available The paper deals with an analysis of temperatures of ground masses in the proximities of linear and slinky-type HGHE (horizontal ground heat exchanger. It evaluates and compares the potentials of HGHEs and ambient air. The reason and aim of the verification was to gain knowledge of the temperature course of the monitored low-temperature heat pump energy sources during heating periods and periods of stagnation and to analyse the knowledge in terms of the potential to use those sources for heat pumps. The study was conducted in the years 2012–2015 during three heating periods and three periods of HGHEs stagnation. The results revealed that linear HGHE had the highest temperature potential of the observed low-temperature heat pump energy sources. The average daily temperatures of the ground mass surrounding the linear HGHE were the highest ranging from 7.08 °C to 9.20 °C during the heating periods, and having the lowest temperature variation range of 12.62–15.14 K, the relative frequency of the average daily temperatures of the ground mass being the highest at 22.64% in the temperature range containing the mode of all monitored temperatures in a recorded interval of [4.10, 6.00] °C. Ambient air had lower temperature potential than the monitored HGHEs.

  18. Comparison of Low-temperature District Heating Concepts in a Long-Term Energy System Perspective

    DEFF Research Database (Denmark)

    Lund, Rasmus Søgaard; Østergaard, Dorte Skaarup; Yang, Xiaochen

    2017-01-01

    into account the grid losses, production efficiencies and building requirements. The scenarios are modelled and analysed in the analysis tool EnergyPLAN and compared on primary energy supply and socioeconomic costs. The results show that the low temperature solution (55/25 oC) has the lowest costs, reducing...... the total costs by about 100 M€/year in 2050....

  19. The Temperature Condition of the Plate with Temperature-Dependent Thermal Conductivity and Energy Release

    OpenAIRE

    V. S. Zarubin; A. V. Kotovich; G. N. Kuvyrkin

    2016-01-01

    The temperature state of a solid body, in addition to the conditions of its heat exchange with the environment, can greatly depend on the heat release (or heat absorption) processes within the body volume. Among the possible causes of these processes should be noted such as a power release in the fuel elements of nuclear reactors, exothermic or endothermic chemical reactions in the solid body material, which respectively involve heat release or absorbtion, heat transfer of a part of the elect...

  20. An energy balance perspective on regional CO2-induced temperature changes in CMIP5 models

    OpenAIRE

    Räisänen, Jouni

    2017-01-01

    An energy balance decomposition of temperature changes is conducted for idealized transient CO2-only simulations in the fifth phase of the Coupled Model Intercomparison Project. The multimodel global mean warming is dominated by enhanced clear-sky greenhouse effect due to increased CO2 and water vapour, but other components of the energy balance substantially modify the geographical and seasonal patterns of the change. Changes in the net surface energy flux are important over the oceans, bein...

  1. Trends and Implications of Stream Temperature for Energy and Fish Production

    Science.gov (United States)

    Zhang, X.; Li, H. Y.; Liu, L.; Hejazi, M. I.; Leung, L. R.

    2015-12-01

    Stream temperature plays an important role in closing the energy balance at local, regional and global scales, and has significant impacts on fishery and energy production. It is therefore a critical parameter in the water-food-energy nexus. The stream temperature is affected by both climatic conditions and human activities such as reservoir and power plant operations. This study adopts a physically based stream temperature model within the Community Earth System Model (CESM) framework. The Model for Scale Adaptive River Transport (MOSART) has been developed to represent riverine water dynamics and incorporated into CESM by coupling with the Community Land Model (CLM). Here we build upon CLM-MOSART to represent the riverine transport of heat along with water flux and the energy exchanges between river water and the atmosphere. The impacts of reservoir and power plant operations are also explicitly incorporated with this stream temperature model. Scenarios of climate change effects as well as climate change combined with human activities are simulated. Trend in stream temperature, especially summer stream, will be systematically analyzed. Discussions of how future stream temperature affects energy production and food security will be presented.

  2. Encapsulation of High Temperature Phase Change Materials for Thermal Energy Storage

    Science.gov (United States)

    Nath, Rupa

    Thermal energy storage is a major contributor to bridge the gap between energy demand (consumption) and energy production (supply) by concentrating solar power. The utilization of high latent heat storage capability of phase change materials is one of the keys to an efficient way to store thermal energy. However, some of the limitations of the existing technology are the high volumetric expansion and low thermal conductivity of phase change materials (PCMs), low energy density, low operation temperatures and high cost. The present work deals with encapsulated PCM system, which operates at temperatures above 500°C and takes advantage of the heat transfer modes at such high temperatures to overcome the aforementioned limitations of PCMs. Encapsulation with sodium silicate coating on preformed PCM pellets were investigated. A low cost, high temperature metal, carbon steel has been used as a capsule for PCMs with a melting point above 500° C. Sodium silicate and high temperature paints were used for oxidation protection of steel at high temperatures. The emissivity of the coatings to enhance heat transfer was investigated.

  3. Mass and energy balance of the carbonization of babassu nutshell as affected by temperature

    Directory of Open Access Journals (Sweden)

    Thiago de Paula Protásio

    2014-03-01

    Full Text Available The objective of this work was to evaluate the carbonization yield of babassu nutshell as affected by final temperature, as well as the energy losses involved in the process. Three layers constituting the babassu nut, that is, the epicarp, mesocarp and endocarp, were used together. The material was carbonized, considering the following final temperatures: 450, 550, 650, 750, and 850ºC. The following were evaluated: energy and charcoal yields, pyroligneous liquid, non-condensable gases, and fixed carbon. The use of babassu nutshell can be highly feasible for charcoal production. The yield of charcoal from babassu nutshell carbonization was higher than that reported in the literature for Eucalyptus wood carbonization, considering the final temperature of 450ºC. Charcoal and energy yields decreased more sharply at lower temperatures, with a tendency to stabilize at higher temperatures. The energy yields obtained can be considered satisfactory, with losses between 45 and 52% (based on higher heating value and between 43 and 49% (based on lower heating value at temperatures ranging from 450 to 850ºC, respectively. Yields in fixed carbon and pyroligneous liquid are not affected by the final carbonization temperature.

  4. Analysis of temperature difference on the total of energy expenditure during static bicycle exercise

    Science.gov (United States)

    Sugiono

    2016-04-01

    How to manage energy expenditure for cyclist is very crucial part to achieve a good performance. As the tropical situation, the differences of temperature level might be contributed in energy expenditure and durability. The aim of the paper is to estimate and to analysis the configuration of energy expenditure for static cycling activity based on heart rate value in room with air conditioning (AC)/no AC treatment. The research is started with study literatures of climate factors, temperature impact on human body, and definition of energy expenditure. The next step is design the experiment for 5 participants in 2 difference models for 26.80C - 74% relative humidity (room no AC) and 23,80C - 54.8% relative humidity (room with AC). The participants’ heart rate and blood pressure are measured in rest condition and in cycling condition to know the impact of difference temperature in energy expenditure profile. According to the experiment results, the reducing of the temperature has significantly impact on the decreasing of energy expenditure at average 0.3 Kcal/minute for all 5 performers. Finally, the research shows that climate condition (temperature and relative humidity) are very important factors to manage and to reach a higher performance of cycling sport.

  5. Effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interface temperature and surface energy

    Directory of Open Access Journals (Sweden)

    Tong Wen

    Full Text Available The microwave-assisted leaching was a new approach to intensify the copper recovery from chalcopyrite by hydrometallurgy. In this work, the effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interfacial reaction temperature and surface energy were investigated. The activation energy of chalcopyrite leaching was affected indistinctively by the microwave-assisted heating (39.1 kJ/mol compared with the conventional heating (43.9 kJ/mol. However, the boiling point of the leaching system increased through microwave-assisted heating. Because of the improved boiling point and the selective heating of microwave, the interfacial reaction temperature increased significantly, which gave rise to the increase of the leaching recovery of copper. Moreover, the surface energy of the chalcopyrite through microwave-assisted heating was also enhanced, which was beneficial to strengthen the leaching of chalcopyrite. Keywords: Microwave-assisted heating, Chalcopyrite, Leaching kinetics, Interface temperature, Surface energy

  6. Effect of temperature on skeletal muscle energy turnover during dynamic knee-extensor exercise in humans

    DEFF Research Database (Denmark)

    Ferguson, R.A.; Krustrup, Peter; Kjær, Michael

    2006-01-01

    . Total ATP production (aerobic + anaerobic) was the same between each temperature condition [505.0 mmol/kg (SD 107.2) vs. 527.1 mmol/kg (SD 117.6); C and HT, respectively]. In conclusion, within the range of temperatures studied, passively increasing muscle temperature before exercise has no effect......The present study examined the effect of elevated temperature on muscle energy turnover during dynamic exercise. Nine male subjects performed 10 min of dynamic knee-extensor exercise at an intensity of 43 W (SD 10) and a frequency of 60 contractions per minute. Exercise was performed under normal...... (C) and elevated muscle temperature (HT) through passive heating. Thigh oxygen uptake (V(O2)) was determined from measurements of thigh blood flow and femoral arterial-venous differences for oxygen content. Anaerobic energy turnover was estimated from measurements of lactate release as well as muscle...

  7. Consequences of complex environments: Temperature and energy intake interact to influence growth and metabolic rate.

    Science.gov (United States)

    Stahlschmidt, Zachary R; Jodrey, Alicia D; Luoma, Rachel L

    2015-09-01

    The field of comparative physiology has a rich history of elegantly examining the effects of individual environmental factors on performance traits linked to fitness (e.g., thermal performance curves for locomotion). However, animals live in complex environments wherein multiple environmental factors co-vary. Thus, we investigated the independent and interactive effects of temperature and energy intake on the growth and metabolic rate of juvenile corn snakes (Pantherophis guttatus) in the context of shifts in complex environments. Unlike previous studies that imposed constant or fluctuating temperature regimes, we manipulated the availability of preferred thermal microclimates (control vs. relatively warm regimes) for eight weeks and allowed snakes to behaviorally thermoregulate among microclimates. By also controlling for energy intake, we demonstrate an interactive effect of temperature and energy on growth-relevant temperature shifts had no effect on snakes' growth when energy intake was low and a positive effect on growth when energy intake was high. Thus, acclimation to relatively warm thermal options can result in increased rates of growth when food is abundant in a taxon in which body size confers fitness advantages. Temperature and energy also interactively influenced metabolic rate-snakes in the warmer temperature regime exhibited reduced metabolic rate (O2 consumption rate at 25 °C and 30 °C) if they had relatively high energy intake. Although we advocate for continued investigation into the effects of complex environments on other traits, our results indicate that warming may actually benefit important life history traits in some taxa and that metabolic shifts may underlie thermal acclimation. Copyright © 2015 Elsevier Inc. All rights reserved.

  8. Temperature-Dependent Ellipsometry Measurements of Partial Coulomb Energy in Superconducting Cuprates

    Science.gov (United States)

    Levallois, J.; Tran, M. K.; Pouliot, D.; Presura, C. N.; Greene, L. H.; Eckstein, J. N.; Uccelli, J.; Giannini, E.; Gu, G. D.; Leggett, A. J.; van der Marel, D.

    2016-07-01

    We performed an experimental study of the temperature and doping dependence of the energy-loss function of the bilayer and trilayer bismuth cuprates family. The primary aim is to obtain information on the energy stored in the Coulomb interaction between the conduction electrons, on the temperature dependence thereof, and on the change of Coulomb interaction when Cooper pairs are formed. We performed temperature-dependent ellipsometry measurements on several Bi2 Sr2 CaCu2 O8 -x single crystals: underdoped with Tc=60 , 70, and 83 K; optimally doped with Tc=91 K ; overdoped with Tc=84 , 81, 70, and 58 K; as well as optimally doped Bi2 Sr2 Ca2 Cu3 O10 +x with Tc=110 K . Our first observation is that, as the temperature drops through Tc, the loss function in the range up to 2 eV displays a change of temperature dependence as compared to the temperature dependence in the normal state. This effect at—or close to—Tc depends strongly on doping, with a sign change for weak overdoping. The size of the observed change in Coulomb energy, using an extrapolation with reasonable assumptions about its q dependence, is about the same size as the condensation energy that has been measured in these compounds. Our results therefore lend support to the notion that the Coulomb energy is an important factor for stabilizing the superconducting phase. Because of the restriction to small momentum, our observations do not exclude a possible significant contribution to the condensation energy of the Coulomb energy associated with the region of q around (π ,π ).

  9. Temperature-Dependent Ellipsometry Measurements of Partial Coulomb Energy in Superconducting Cuprates

    Directory of Open Access Journals (Sweden)

    J. Levallois

    2016-08-01

    Full Text Available We performed an experimental study of the temperature and doping dependence of the energy-loss function of the bilayer and trilayer bismuth cuprates family. The primary aim is to obtain information on the energy stored in the Coulomb interaction between the conduction electrons, on the temperature dependence thereof, and on the change of Coulomb interaction when Cooper pairs are formed. We performed temperature-dependent ellipsometry measurements on several Bi_{2}Sr_{2}CaCu_{2}O_{8-x} single crystals: underdoped with T_{c}=60, 70, and 83 K; optimally doped with T_{c}=91  K; overdoped with T_{c}=84, 81, 70, and 58 K; as well as optimally doped Bi_{2}Sr_{2}Ca_{2}Cu_{3}O_{10+x} with T_{c}=110  K. Our first observation is that, as the temperature drops through T_{c}, the loss function in the range up to 2 eV displays a change of temperature dependence as compared to the temperature dependence in the normal state. This effect at—or close to—T_{c} depends strongly on doping, with a sign change for weak overdoping. The size of the observed change in Coulomb energy, using an extrapolation with reasonable assumptions about its q dependence, is about the same size as the condensation energy that has been measured in these compounds. Our results therefore lend support to the notion that the Coulomb energy is an important factor for stabilizing the superconducting phase. Because of the restriction to small momentum, our observations do not exclude a possible significant contribution to the condensation energy of the Coulomb energy associated with the region of q around (π,π.

  10. Efficient energy transfer in light-harvesting systems, I: optimal temperature, reorganization energy and spatial-temporal correlations

    Energy Technology Data Exchange (ETDEWEB)

    Wu Jianlan; Liu Fan; Shen Young; Cao Jianshu; Silbey, Robert J, E-mail: jianshu@mit.ed, E-mail: silbey@mit.ed [Department of Chemistry, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States)

    2010-10-15

    Understanding the mechanisms of efficient and robust energy transfer in light-harvesting systems provides new insights for the optimal design of artificial systems. In this paper, we use the Fenna-Matthews-Olson (FMO) protein complex and phycocyanin 645 (PC 645) to explore the general dependence on physical parameters that help maximize the efficiency and maintain its stability. With the Haken-Strobl model, the maximal energy transfer efficiency (ETE) is achieved under an intermediate optimal value of dephasing rate. To avoid the infinite temperature assumption in the Haken-Strobl model and the failure of the Redfield equation in predicting the Forster rate behavior, we use the generalized Bloch-Redfield (GBR) equation approach to correctly describe dissipative exciton dynamics, and we find that maximal ETE can be achieved under various physical conditions, including temperature, reorganization energy and spatial-temporal correlations in noise. We also identify regimes of reorganization energy where the ETE changes monotonically with temperature or spatial correlation and therefore cannot be optimized with respect to these two variables.

  11. An energy balance perspective on regional CO2-induced temperature changes in CMIP5 models

    Science.gov (United States)

    Räisänen, Jouni

    2017-05-01

    An energy balance decomposition of temperature changes is conducted for idealized transient CO2-only simulations in the fifth phase of the Coupled Model Intercomparison Project. The multimodel global mean warming is dominated by enhanced clear-sky greenhouse effect due to increased CO2 and water vapour, but other components of the energy balance substantially modify the geographical and seasonal patterns of the change. Changes in the net surface energy flux are important over the oceans, being especially crucial for the muted warming over the northern North Atlantic and for the seasonal cycle of warming over the Arctic Ocean. Changes in atmospheric energy flux convergence tend to smooth the gradients of temperature change and reduce its land-sea contrast, but they also amplify the seasonal cycle of warming in northern North America and Eurasia. The three most important terms for intermodel differences in warming are the changes in the clear-sky greenhouse effect, clouds, and the net surface energy flux, making the largest contribution to the standard deviation of annual mean temperature change in 34, 29 and 20 % of the world, respectively. Changes in atmospheric energy flux convergence mostly damp intermodel variations of temperature change especially over the oceans. However, the opposite is true for example in Greenland and Antarctica, where the warming appears to be substantially controlled by heat transport from the surrounding sea areas.

  12. Estimating the Surface Air Temperature by Remote Sensing in Northwest China Using an Improved Advection-Energy Balance for Air Temperature Model

    OpenAIRE

    Suhua Liu; Hongbo Su; Renhua Zhang; Jing Tian; Weizhen Wang

    2016-01-01

    To estimate the surface air temperature by remote sensing, the advection-energy balance for the surface air temperature (ADEBAT) model is developed which assumes the surface air temperature is driven by the local driving force and the advective driving force. The local driving force produces a local surface air temperature whereas the advective driving force changes it by adding an exotic air temperature. An advection factor f is defined to measure the quantity of the exotic air brought by th...

  13. Enhancing Low-Grade Thermal Energy Recovery in a Thermally Regenerative Ammonia Battery Using Elevated Temperatures

    KAUST Repository

    Zhang, Fang

    2015-02-13

    © 2015 WILEY-VCH Verlag GmbH & Co. KGaA. A thermally regenerative ammonia battery (TRAB) is a new approach for converting low-grade thermal energy into electricity by using an ammonia electrolyte and copper electrodes. TRAB operation at 72°C produced a power density of 236±8 Wm-2, with a linear decrease in power to 95±5 Wm-2 at 23°C. The improved power at higher temperatures was due to reduced electrode overpotentials and more favorable thermodynamics for the anode reaction (copper oxidation). The energy density varied with temperature and discharge rates, with a maximum of 650 Whm-3 at a discharge energy efficiency of 54% and a temperature of 37°C. The energy efficiency calculated with chemical process simulation software indicated a Carnot-based efficiency of up to 13% and an overall thermal energy recovery of 0.5%. It should be possible to substantially improve these energy recoveries through optimization of electrolyte concentrations and by using improved ion-selective membranes and energy recovery systems such as heat exchangers.

  14. Investigation of the stochastic nature of temperature and humidity for energy management

    Science.gov (United States)

    Hadjimitsis, Evanthis; Demetriou, Evangelos; Sakellari, Katerina; Tyralis, Hristos; Iliopoulou, Theano; Koutsoyiannis, Demetris

    2017-04-01

    Atmospheric temperature and dew point, in addition to their role in atmospheric processes, influence the management of energy systems since they highly affect the energy demand and production. Both temperature and humidity depend on the climate conditions and geographical location. In this context, we analyze numerous of observations around the globe and we investigate the long-term behaviour and periodicities of the temperature and humidity processes. Also, we present and apply a parsimonious stochastic double-cyclostationary model for these processes to an island in the Aegean Sea and investigate their link to energy management. Acknowledgement: This research is conducted within the frame of the undergraduate course "Stochastic Methods in Water Resources" of the National Technical University of Athens (NTUA). The School of Civil Engineering of NTUA provided moral support for the participation of the students in the Assembly.

  15. Temperature-Responsive Luminescent Solar Concentrators: Tuning Energy Transfer in a Liquid Crystalline Matrix.

    Science.gov (United States)

    Sol, Jeroen A H P; Dehm, Volker; Hecht, Reinhard; Würthner, Frank; Schenning, Albertus P H J; Debije, Michael G

    2018-01-22

    Temperature-responsive luminescent solar concentrators (LSCs) have been fabricated in which the Förster resonance energy transfer (FRET) between a donor-acceptor pair in a liquid crystalline solvent can be tuned. At room temperatures, the perylene bisimide (PBI) acceptor is aggregated and FRET is inactive; while after heating to a temperature above the isotropic phase of the liquid crystal solvent, the acceptor PBI completely dissolves and FRET is activated. This unusual temperature control over FRET was used to design a color-tunable LSC. The device has been shown to be highly stable towards consecutive heating and cooling cycles, making it an appealing device for harvesting otherwise unused solar energy. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

  16. Study on the optimum PCM melting temperature for energy savings in residential buildings worldwide

    Science.gov (United States)

    Saffari, M.; de Gracia, A.; Fernández, C.; Zsembinszki, G.; Cabeza, L. F.

    2017-10-01

    To maintain comfort conditions in residential buildings along a full year period, the use of active systems is generally required to either supply heating or cooling. The heating and cooling demands strongly depend on the climatic conditions, type of building and occupants’ behaviour. The overall annual energy consumption of the building can be reduced by the use of renewable energy sources and/or passive systems. The use of phase change materials (PCM) as passive systems in buildings enhances the thermal mass of the envelope, and reduces the indoor temperature fluctuations. As a consequence, the overall energy consumption of the building is generally lower as compared to the case when no PCM systems are used. The selection of the PCM melting temperature is a key issue to reduce the energy consumption of the buildings. The main focus of this study is to determine the optimum PCM melting temperature for passive heating and cooling according to different weather conditions. To achieve that, numerical simulations were carried out using EnergyPlus v8.4 coupled with GenOpt® v3.1.1 (a generic optimization software). A multi-family residential apartment was selected from ASHRAE Standard 90.1- 2013 prototype building model, and different climate conditions were considered to determine the optimum melting temperature (in the range from 20ºC to 26ºC) of the PCM contained in gypsum panels. The results confirm that the optimum melting temperature of the PCM strongly depends on the climatic conditions. In general, in cooling dominant climates the optimum PCM temperature is around 26ºC, while in heating dominant climates it is around 20ºC. Furthermore, the results show that an adequate selection of the PCM as passive system in building envelope can provide important energy savings for both heating dominant and cooling dominant regions.

  17. An insertion to eliminate horizontal temperature of high energy electron beam

    Energy Technology Data Exchange (ETDEWEB)

    Burov, A.V. [AN SSSR, Novosibirsk (Russian Federation). Inst. Yadernoj Fiziki; Danilov, V.V. [AN SSSR, Novosibirsk (Russian Federation). Inst. Yadernoj Fiziki

    1998-03-16

    High energy electron cooling with a circulated electron bunch could significantly increase the luminosity of hadron colliders. One of the significant obstacles is high horizontal temperature of electron bunches, suppressing dramatically calculated cooling rates. Recently, a transformation of betatron coordinates and angles for elimination of the radial temperature was found. In our paper, we present a simple scheme to make up this transformation by thin quadruples, drifts and a solenoid.

  18. Integration of body temperature into the analysis of energy expenditure in the mouse

    Directory of Open Access Journals (Sweden)

    Gustavo Abreu-Vieira

    2015-06-01

    Conclusions: At 22 °C, cold-induced thermogenesis is ∼120% of basal metabolic rate. The higher body temperature during physical activity is due to a higher set point, not simply increased heat generation during exercise. Most insulation in mice is via physiological mechanisms, with little from fur or fat. Our analysis suggests that the definition of the upper limit of the thermoneutral zone should be re-considered. Measuring body temperature informs interpretation of energy expenditure data and improves the predictiveness and utility of the mouse to model human energy homeostasis.

  19. Debye temperature for binary alloys and its relationship with cohesive energy

    Science.gov (United States)

    Tang, Kewei; Wang, Tianran; Qi, Weihong; Li, Yejun

    2018-02-01

    The cohesive energy, formation enthalpies, and elastic constants of AgAl, AuAg, AuPd, AuPt, CuNi, CuPt, NiPb, NiPd, NiPt, and PtPd alloys are calculated by molecular dynamics simulation and first-principle calculation. It is found that the calculated formation enthalpies generally agree with the availible experimental data. The Debye temperatures of these alloys with different compositions are computed from the obtained elastic constants. An empirical relationship between Debye temperature and cohesive energy is developed, which is confirmed by both the simulation and calculation.

  20. High Temperature Fusion Reactor Cooling Using Brayton Cycle Based Partial Energy Conversion

    Science.gov (United States)

    Juhasz, Albert J.; Sawicki, Jerzy T.

    2003-01-01

    For some future space power systems using high temperature nuclear heat sources most of the output energy will be used in other than electrical form, and only a fraction of the total thermal energy generated will need to be converted to electrical work. The paper describes the conceptual design of such a partial energy conversion system, consisting of a high temperature fusion reactor operating in series with a high temperature radiator and in parallel with dual closed cycle gas turbine (CCGT) power systems, also referred to as closed Brayton cycle (CBC) systems, which are supplied with a fraction of the reactor thermal energy for conversion to electric power. Most of the fusion reactor's output is in the form of charged plasma which is expanded through a magnetic nozzle of the interplanetary propulsion system. Reactor heat energy is ducted to the high temperature series radiator utilizing the electric power generated to drive a helium gas circulation fan. In addition to discussing the thermodynamic aspects of the system design the authors include a brief overview of the gas turbine and fan rotor-dynamics and proposed bearing support technology along with performance characteristics of the three phase AC electric power generator and fan drive motor.

  1. Use of Low-Temperature Geothermal Energy for Desalination in the Western United States

    Energy Technology Data Exchange (ETDEWEB)

    Turchi, Craig S. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Akar, Sertac [National Renewable Energy Lab. (NREL), Golden, CO (United States); Cath, Tzahi [Colorado School of Mines, Golden, CO (United States); Vanneste, Johan [Colorado School of Mines, Golden, CO (United States); Geza, Mengistu [Colorado School of Mines, Golden, CO (United States)

    2015-11-01

    This joint project between the National Renewable Energy Laboratory and the Colorado School of Mines has examined the potential of using low-temperature geothermal resources for desalination. The temperature range in question is not well suited for electricity generation, but can be used for direct heating. Accordingly, the best integration approaches use thermal desalination technologies such as multi-effect distillation (MED) or membrane distillation (MD), rather than electric-driven technologies such as reverse osmosis (RO). The examination of different desalination technologies led to the selection of MD for pairing with geothermal energy. MD operates at near-ambient pressure and temperatures less than 100°C with hydrophobic membranes. The technology is modular like RO, but the equipment costs are lower. The thermal energy demands of MD are higher than MED, but this is offset by an ability to run at lower temperatures and a low capital cost. Consequently, a geothermal-MD system could offer a low capital cost and, if paired with low-cost geothermal energy, a low operating cost. The target product water cost is $1.0 to $1.5 per cubic meter depending on system capacity and the cost of thermal energy.

  2. The power processor of a high temperature superconducting energy storage system

    Energy Technology Data Exchange (ETDEWEB)

    Ollila, J. [Power Electronics, Tampere University of Technology, Tampere (Finland)

    1997-12-31

    This report introduces the structure and properties of a power processor unit for a high temperature superconducting magnetic energy storage system which is bused in an UPS demonstration application. The operation is first demonstrated using simulations. The software based operating and control system utilising combined Delta-Sigma and Sliding-Mode control is described shortly. Preliminary test results using a conventional NbTi superconducting energy y storage magnet operating at 4.2 K is shown. (orig.)

  3. Electromagnetic properties of terbium gallium garnet at millikelvin temperatures and low photon energy

    Science.gov (United States)

    Kostylev, Nikita; Goryachev, Maxim; Bushev, Pavel; Tobar, Michael E.

    2017-07-01

    Electromagnetic properties of single crystal terbium gallium garnet are characterised from room down to millikelvin temperatures using the whispering gallery mode method. Microwave spectroscopy is performed at low powers equivalent to a few photons in energy and conducted as functions of the magnetic field and temperature. A phase transition is detected close to the temperature of 3.5 K. This is observed for multiple whispering gallery modes causing an abrupt negative frequency shift and a change in transmission due to extra losses in the new phase caused by a change in complex magnetic susceptibility.

  4. Energy consumption and temperature correlations for 4 Greek Ionian Sea islands

    Science.gov (United States)

    Psiloglou, B.; Giannakopoulos, C.; Dagoumas, A.; Skourtis, K.

    2012-04-01

    Energy consumption, especially for space heating and cooling, is linked to several weather variables, mainly air temperature. This study investigates the relationship between residential energy consumption load demand and daily mean air temperature for 4 Greek islands in the Ionian Sea for the period 2005-2011.These islands are Zante, Cephallonia, Corfu and Lefkada and were selected due to their data availability as they are interconnected to the mainland power distribution system. We present the time series of diurnal, daily, monthly and yearly variations of energy consumption for each of the selected sites and subsequently identify correlations with mean daily air temperature. Several effects such as weekly and holiday effects, unrelated to weather conditions, can be detected. Daily and monthly seasonal effects have been studied separately to isolate the weather influence on energy consumption. The most important finding, however, is the outstanding increase in consumption during the tourism season. Depending on the island, increased levels of consumption are present for 4,5 or more months per year, related to tourists arrivals on the island. This effect combined with energy consumption peaks on the hot days of the year should be taken into account during energy conservation planning.

  5. Effective Energy Transfer via Plasmon-Activated High-Energy Water Promotes Its Fundamental Activities of Solubility, Ionic Conductivity, and Extraction at Room Temperature

    National Research Council Canada - National Science Library

    Yang, Chih-Ping; Chen, Hsiao-Chien; Wang, Ching-Chiung; Tsai, Po-Wei; Ho, Chia-Wen; Liu, Yu-Chuan

    2015-01-01

    ... conductivity, and extraction at room temperature. High-energy water with reduced HBs was created by utilizing hot electrons with energies from the decay of surface plasmon excited at gold (Au) nanoparticles (NPs...

  6. Quantifying energy and mass transfer in crop canopies: sensors for measurement of temperature and air velocity

    Science.gov (United States)

    Bugbee, B.; Monje, O.; Tanner, B.

    1996-01-01

    Here we report on the in situ performance of inexpensive, miniature sensors that have increased our ability to measure mass and energy fluxes from plant canopies in controlled environments: 1. Surface temperature. Canopy temperature measurements indicate changes in stomatal aperture and thus latent and sensible heat fluxes. Infrared transducers from two manufacturers (Exergen Corporation, Newton, MA; and Everest Interscience, Tucson, AZ, USA) have recently become available. Transducer accuracy matched that of a more expensive hand-held infrared thermometer. 2. Air velocity varies above and within plant canopies and is an important component in mass and energy transfer models. We tested commercially-available needle, heat-transfer anemometers (1 x 50 mm cylinder) that consist of a fine-wire thermocouple and a heater inside a hypodermic needle. The needle is heated and wind speed determined from the temperature rise above ambient. These sensors are particularly useful in measuring the low wind speeds found within plant canopies. 3. Accurate measurements of air temperature adjacent to plant leaves facilitates transport phenomena modeling. We quantified the effect of radiation and air velocity on temperature rise in thermocouples from 10 to 500 micrometers. At high radiation loads and low wind speeds, temperature errors were as large as 7 degrees C above air temperature.

  7. The Significance of Temperature Based Approach Over the Energy Based Approaches in the Buildings Thermal Assessment

    Science.gov (United States)

    Albatayneh, Aiman; Alterman, Dariusz; Page, Adrian; Moghtaderi, Behdad

    2017-05-01

    The design of low energy buildings requires accurate thermal simulation software to assess the heating and cooling loads. Such designs should sustain thermal comfort for occupants and promote less energy usage over the life time of any building. One of the house energy rating used in Australia is AccuRate, star rating tool to assess and compare the thermal performance of various buildings where the heating and cooling loads are calculated based on fixed operational temperatures between 20 °C to 25 °C to sustain thermal comfort for the occupants. However, these fixed settings for the time and temperatures considerably increase the heating and cooling loads. On the other hand the adaptive thermal model applies a broader range of weather conditions, interacts with the occupants and promotes low energy solutions to maintain thermal comfort. This can be achieved by natural ventilation (opening window/doors), suitable clothes, shading and low energy heating/cooling solutions for the occupied spaces (rooms). These activities will save significant amount of operating energy what can to be taken into account to predict energy consumption for a building. Most of the buildings thermal assessment tools depend on energy-based approaches to predict the thermal performance of any building e.g. AccuRate in Australia. This approach encourages the use of energy to maintain thermal comfort. This paper describes the advantages of a temperature-based approach to assess the building's thermal performance (using an adaptive thermal comfort model) over energy based approach (AccuRate Software used in Australia). The temperature-based approach was validated and compared with the energy-based approach using four full scale housing test modules located in Newcastle, Australia (Cavity Brick (CB), Insulated Cavity Brick (InsCB), Insulated Brick Veneer (InsBV) and Insulated Reverse Brick Veneer (InsRBV)) subjected to a range of seasonal conditions in a moderate climate. The time required for

  8. High temperature solid oxide regenerative fuel cell for solar photovoltaic energy storage

    Science.gov (United States)

    Bents, David J.

    1987-01-01

    A hydrogen-oxygen regenerative fuel cell energy storage system based on high temperature solid oxide fuel cell technology is discussed which has application to darkside energy storage for solar photovoltaics. The forward and reverse operating cycles are described, and heat flow, mass, and energy balance data are presented to characterize the system's performance and the variation of performance with changing reactant storage pressure. The present system weighs less than nickel hydrogen battery systems after 0.7 darkside operation, and it maintains a specific weight advantage over radioisotope generators for discharge periods up to 72 hours.

  9. Reconstruction of soil surface temperature via Fourier analysis to quantify surface energy fluxes

    Science.gov (United States)

    Schenk, Gabriele; Wollschläger, Ute; Roth, Kurt

    2010-05-01

    Quantifying the surface energy and water balance is a prerequisite for understanding the complex interplay between the atmospheric and terrestrial part of the earth. Therefore, it is necessary to estimate the partitioning of the incoming solar energy into ground heat flux, latent and sensible heat. The amount of evaporating water can be measured by the expensive and elaborated eddy-covariance method, but in general measurements of surface fluxes are difficult to obtain. This is why they are often determined from more theoretical approaches based on energy budget calculations at the soil surface. To compute, e.g., the latent heat portion, this indirect methods, like Penman-Monteith, make use of various atmospheric quantities, but usually lack information about the temperature right at the soil surface which therefore needs to be approximated. We investigate synthetic and field measured soil temperature data via Fourier analysis to extract the frequency information of temperature readings in different depths. This allows us to determine the apparent thermal soil diffusivity and to project back all frequency components from within the soil profile towards the surface. This yields a reconstruction of the temperature at the upper soil boundary which can directly be used to calculate the energy balance at the interface to the atmosphere. We will present the performance of the projection for synthetic data for which the method could be validated very well. Assumptions and approximations made will be discussed. Furthermore, we will demonstrate its application to field-measured data from our test site next to Heidelberg, Germany.

  10. An Examination of Cross Sectional Change in Student's Metaphorical Perceptions towards Heat, Temperature and Energy Concepts

    Science.gov (United States)

    Celik, Harun

    2016-01-01

    In science teaching, metaphors are important tools for understanding meaningful learning and conceptual formation by the help of daily life language. This study aims to evaluate how the concepts of heat, temperature and energy are perceived by students in secondary school science classes and how the perceptions of these concepts vary in terms of…

  11. Similarity between turbulent kinetic energy and temperature spectra in the near-wall region

    Science.gov (United States)

    Antonia, R. A.; Kim, J.

    1991-01-01

    The similarity between turbulent kinetic energy and temperature spectra, previously confirmed using experimental data in various turbulent shear flows, is validated in the near-wall region using direct numerical simulation data in a fully developed turbulent channel flow. The dependence of this similarity on the molecular Prandtl number is also examined.

  12. Ambient Temperature Based Thermal Aware Energy Efficient ROM Design on FPGA

    DEFF Research Database (Denmark)

    Saini, Rishita; Bansal, Neha; Bansal, Meenakshi

    2015-01-01

    Thermal aware design is currently gaining importance in VLSI research domain. In this work, we are going to design thermal aware energy efficient ROM on Virtex-5 FPGA. Ambient Temperature, airflow, and heat sink profile play a significant role in thermal aware hardware design life cycle. Ambient...

  13. Transient energy growth modulation by temperature dependent transport properties in a stratified plane Poiseuille flow

    NARCIS (Netherlands)

    Rinaldi, E.; Boersma, B.J.; Pecnik, R.

    2015-01-01

    We investigate the effect of temperature dependent thermal conductivity ? and isobaric specific heat c_P on the transient amplification of perturbations in a thermally stratified laminar plane Poiseuille flow. It is shown that for decreasing thermal conductivity the maximum transient energy growth

  14. A Simple Method to Calculate the Temperature Dependence of the Gibbs Energy and Chemical Equilibrium Constants

    Science.gov (United States)

    Vargas, Francisco M.

    2014-01-01

    The temperature dependence of the Gibbs energy and important quantities such as Henry's law constants, activity coefficients, and chemical equilibrium constants is usually calculated by using the Gibbs-Helmholtz equation. Although, this is a well-known approach and traditionally covered as part of any physical chemistry course, the required…

  15. Influence of Energy and Temperature in Cluster Coalescence Induced by Deposition

    Directory of Open Access Journals (Sweden)

    J. C. Jiménez-Sáez

    2012-01-01

    Full Text Available Coalescence induced by deposition of different Cu clusters on an epitaxial Co cluster supported on a Cu(001 substrate is studied by constant-temperature molecular dynamics simulations. The degree of epitaxy of the final system increases with increasing separation between the centres of mass of the projectile and target clusters during the collision. Structure, roughness, and epitaxial order of the supported cluster also influence the degree of epitaxy. The effect of energy and temperature is determinant on the epitaxial condition of the coalesced cluster, especially both factors modify the generation, growth and interaction among grains. A higher temperature favours the epitaxial growth for low impact parameters. A higher energy contributes to the epitaxial coalescence for any initial separation between the projectile and target clusters. The influence of projectile energy is notably greater than the influence of temperature since higher energies allow greater and instantaneous atomic reorganizations, so that the number of arisen grains just after the collision becomes smaller. The appearance of grain boundary dislocations is, therefore, a decisive factor in the epitaxial growth of the coalesced cluster.

  16. Is there a temperature? conceptual challenges at high energy, acceleration and complexity

    CERN Document Server

    Sándor Biró, Tamás

    2011-01-01

    Physical bodies can be hot or cold, moving or standing,simple or complex. In all such cases one assumes that their respective temperature is a well defined attribute.  What if, however, the ordinary measurement of temperature by direct body contact is not possible?  One conjectures its value, and yes, its very existence, by reasoning based on basic principles of thermodynamics. Is There a Temperature?  Conceptual Challenges at High Energy, Acceleration and Complexity, by Dr. Tamás Sándor Bíró, begins by asking the questions “Do we understand and can we explain in a unified framework the temperature of distant radiation sources, including event horizons, and that of the quark matter produced in high energy accelerator experiments? Or the astounding fluctuations on financial markets?” The book reviews the concept of temperature from its beginnings through the evolution of classical thermodynamics and atomic statistical physics through contemporary models of high energy particle matter.  Based on the...

  17. Aspects of Energy Metabolism in Mangalitsa Pigs Exposed at Thermic Neutral Temperature

    Directory of Open Access Journals (Sweden)

    Monica Pârvu

    2011-10-01

    Full Text Available The studies aimed the energy metabolism determination in Mangalitsa pigs exposed at thermic neutral temperature, compared to Large White pigs. The experimental period was between 80 and 100 kg liveweight. The animals had free access to standard, isoprotein and isocalory diets, with 13.5% crude protein (CP and 3100 kcal/kg metabolizable energy. Feed intake was measured on a daily basis. The energy-protein balance was calculated on the basis of comparative slaughter made at the beginning and end of the experiment. The metabolizable energy (MEc was estimated by chemical analysis (feed and excreta using mathematical modelling and the Whittemore’s formula. The metabolizable energy utilization efficiency was 0.61 at Large White and 0.53 at Mangalitsa.

  18. Raman distributed temperature measurement at CERN high energy accelerator mixed field radiation test facility (CHARM)

    Science.gov (United States)

    Toccafondo, Iacopo; Nannipieri, Tiziano; Signorini, Alessandro; Guillermain, Elisa; Kuhnhenn, Jochen; Brugger, Markus; Di Pasquale, Fabrizio

    2015-09-01

    In this paper we present a validation of distributed Raman temperature sensing (RDTS) at the CERN high energy accelerator mixed field radiation test facility (CHARM), newly developed in order to qualify electronics for the challenging radiation environment of accelerators and connected high energy physics experiments. By investigating the effect of wavelength dependent radiation induced absorption (RIA) on the Raman Stokes and anti-Stokes light components in radiation tolerant Ge-doped multi-mode (MM) graded-index optical fibers, we demonstrate that Raman DTS used in loop configuration is robust to harsh environments in which the fiber is exposed to a mixed radiation field. The temperature profiles measured on commercial Ge-doped optical fibers is fully reliable and therefore, can be used to correct the RIA temperature dependence in distributed radiation sensing systems based on P-doped optical fibers.

  19. Temperature-dependent resonance energy transfer from semiconductor quantum wells to graphene.

    Science.gov (United States)

    Yu, Young-Jun; Kim, Keun Soo; Nam, Jungtae; Kwon, Se Ra; Byun, Hyeryoung; Lee, Kwanjae; Ryou, Jae-Hyun; Dupuis, Russell D; Kim, Jeomoh; Ahn, Gwanghyun; Ryu, Sunmin; Ryu, Mee-Yi; Kim, Jin Soo

    2015-02-11

    Resonance energy transfer (RET) has been employed for interpreting the energy interaction of graphene combined with semiconductor materials such as nanoparticles and quantum-well (QW) heterostructures. Especially, for the application of graphene as a transparent electrode for semiconductor light emitting diodes, the mechanism of exciton recombination processes such as RET in graphene-semiconductor QW heterojunctions should be understood clearly. Here, we characterized the temperature-dependent RET behaviors in graphene/semiconductor QW heterostructures. We then observed the tuning of the RET efficiency from 5% to 30% in graphene/QW heterostructures with ∼60 nm dipole-dipole coupled distance at temperatures of 300 to 10 K. This survey allows us to identify the roles of localized and free excitons in the RET process from the QWs to graphene as a function of temperature.

  20. Effects of boosting the supply temperature on pipe dimensions of low-energy district heating networks

    DEFF Research Database (Denmark)

    Tol, Hakan; Svendsen, Svend

    2015-01-01

    This paper presents a method for the dimensioning of the low-energy District Heating (DH) piping networks operating with a control philosophy of supplying heat in low-temperature such as 55 °C in supply and 25°C in return regularly while the supply temperature levels are being boosted in cold...... winter periods. The performance of the existing radiators that were formerly sized with over-dimensions was analyzed, its results being used as input data for the performance evaluation of the piping network of the low-energy DH system operating with the control philosophy in question. The optimization...... from the DH network. Sensitivity analysis was carried out in order to evaluate the area of applicability of the proposed method. Hence varied values of the original capacity and the current capacity of the existing radiators were evaluated with the design temperature values that were defined by two...

  1. Reducing interior temperature resulting from solar energy using three-dimensional surface patterns

    Directory of Open Access Journals (Sweden)

    Shiang-Jiun Lin

    2015-05-01

    Full Text Available Excessive solar energy can significantly increase interior temperatures and yield great energy demands for air conditioning. Whereas reducing energy consumptions is very crucial today, this article employs patterned glass technology which incorporates linear patterns throughout the exterior surface of glass to attenuate the solar effect on the interior thermal field based on theoretical and experimental studies. By periodically imposing linearly three-dimensional patterns over the outer surface of window glass, the analytical results indicate that the interior solar heat is able to be reduced, as the surface patterns increase the incident angle and/or decrease the solar energy loading on the patterned glass material. Moreover, the interior solar heat can be strongly affected by the pattern design. According to thermally measured results, the trapezoidal patterned glass having 3-mm-top-edged patterned members yields lower temperature on the interior surface of glass comparing with that for the trapezoidal patterns having 6-mm-top edges. Therefore, making the least non-sloped feature or flat plane appearing on the patterned glass helps decrease the interior temperature resulting from solar energy.

  2. Absorbed Energy Distribution of Ductile Ni-resist Alloyed Iron Under Instrumented Impact Load at Low Temperatures

    National Research Council Canada - National Science Library

    Ke, Jiang; Yingdong, Qu; Junhua, You; Rongde, Li

    2016-01-01

    In this study, in order to investigate the absorbed energy distribution on the low-temperature impact fracture process of ductile Ni-resist alloyed iron, the low-temperature impact tests of ductile Ni...

  3. Technologies for decreasing the tap temperature to save energy in steel foundries

    Science.gov (United States)

    Biswas, Siddhartha

    Steel foundries are one of the most energy intensive industries. The increasing concerns over volatile energy cost and carbon dioxide emission have pushed foundries to improve efficiency and hence decrease electrical energy consumption. Statistical analysis of industrial survey data was combined with computational fluid dynamics (CFD) modeling to investigate the best industrial practices and opportunities to improve energy efficiency. Reducing tap temperature was identified as one of the important ways of reducing energy consumption. Steel foundries typically tap at 1650-1800°C (3000-3300°F) which is 100-250°C (150-450°F) higher than the pouring temperature. The steel temperature is elevated to compensate for the temperature loss associated with tapping, holding and transporting the liquid steel from the furnace to the pouring floor. Based on experimental investigations and CFD modeling of heat losses during holding in the ladle for different foundry practices, a spreadsheet calculator has been developed to calculate the optimum tap temperature for the specific foundry practices which will eliminate unnecessary superheating. The calculated results were compared and validated with industrial measurements. Improving the lining refractory is one significant way of reducing heat losses during holding of the steel in ladle. Silica sand linings are being used in steel foundries as an inexpensive and convenient material for short holding times and small volumes. The possibilities of improvements of silica sand linings by the addition of lower density cenospheres (hollow spheres), a byproduct of coal fired power plants, was studied through property measurements and laboratory trials.

  4. Transported Low-Temperature Geothermal Energy for Thermal End Uses Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Zhiyao [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Xiaobing [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gluesenkamp, Kyle R [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mehdizadeh Momen, Ayyoub [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Li, Jan-Mou [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-10-01

    The use of geothermal energy is an emerging area for improving the nation’s energy resiliency. Conventionally, geothermal energy applications have focused on power generation using high temperature hydrothermal resources or enhanced geothermal systems. However, many low temperature (below 150°C/300°F) geothermal resources are also available but have not been fully utilized. For example, it is estimated that 25 billion barrels of geothermal fluid (mostly water and some dissolved solids) at 176°F to 302°F (80°C to 150°C) is coproduced annually at oil and gas wells in the United States (DOE 2015). The heat contained in coproduced geothermal fluid (also referred as “coproduced water”) is typically wasted because the fluid is reinjected back into the ground without extracting the heat.

  5. Effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interface temperature and surface energy

    Science.gov (United States)

    Wen, Tong; Zhao, Yunliang; Xiao, Qihang; Ma, Qiulin; Kang, Shichang; Li, Hongqiang; Song, Shaoxian

    The microwave-assisted leaching was a new approach to intensify the copper recovery from chalcopyrite by hydrometallurgy. In this work, the effect of microwave-assisted heating on chalcopyrite leaching of kinetics, interfacial reaction temperature and surface energy were investigated. The activation energy of chalcopyrite leaching was affected indistinctively by the microwave-assisted heating (39.1 kJ/mol) compared with the conventional heating (43.9 kJ/mol). However, the boiling point of the leaching system increased through microwave-assisted heating. Because of the improved boiling point and the selective heating of microwave, the interfacial reaction temperature increased significantly, which gave rise to the increase of the leaching recovery of copper. Moreover, the surface energy of the chalcopyrite through microwave-assisted heating was also enhanced, which was beneficial to strengthen the leaching of chalcopyrite.

  6. Potential decline in geothermal energy generation due to rising temperatures under climate change scenarios

    Science.gov (United States)

    Angel, E.; Ortega, S.; Gonzalez-Duque, D.; Ruiz-Carrascal, D.

    2016-12-01

    Geothermal energy production depends on the difference between air temperature and the geothermal fluid temperature. The latter remains approximately constant over time, so the power generation varies according to local atmospheric conditions. Projected changes in near-surface air temperatures in the upper levels of the tropical belt are likely to exceed the projected temperature anomalies across many other latitudes, which implies that geothermal plants located in these regions may be affected, reducing their energy output. This study focuses on a hypothetical geothermal power plant, located in the headwaters of the Claro River watershed, a key high-altitude basin in Los Nevados Natural Park, on the El Ruiz-Tolima volcanic massif, in the Colombian Central Andes, a region with a known geothermal potential. Four different Atmospheric General Circulation Models where used to project temperature anomalies for the 2040-2069 prospective period. Their simulation outputs were merged in a differentially-weighted multi-model ensemble, whose weighting factors were defined according to the capability of individual models to reproduce ground truth data from a set of digital data-loggers installed in the basin since 2008 and from weather stations gathering climatic variables since the early 50s. Projected anomalies were computed for each of the Representative Concentration Pathways defined by the IPCC Fifth Assessment Report in the studied region. These climate change projections indicate that air temperatures will likely reach positive anomalies in the range +1.27 ºC to +3.47 ºC, with a mean value of +2.18 ºC. Under these conditions, the annual energy output declines roughly 1% per each degree of increase in near-surface temperature. These results must be taken into account in geothermal project evaluations in the region.

  7. Energy audit of three energy-conserving devices in a steel industry demonstration program. Task III. GTE high temperature recuperation

    Energy Technology Data Exchange (ETDEWEB)

    Holden, F.C.; Hoffman, A.O.; Lownie, H.W.

    1983-06-01

    The Office of Industrial Programs of the Department of Energy has undertaken a program to demonstrate to industry the benefits of installing various energy-conserving devices and equipment. This report presents results on one of those systems, a high-temperature ceramic recuperator designed and manufactured by Sylvania Chemical and Metallurgical Division, GTE Products Corporation of Towanda, Pennsylvania. The ceramic cross-flow recuperator unit recovers waste heat from the hot combustion gases and delivers preheated air to high-temperature burners of various manufacture. Of the 38 host site installations included in the program, sufficient operating data were obtained from 28 sites to evaluate the benefits in terms of energy and economic savings that can be achieved. Performance and cost data are analyzed and presented for those 28 installations, which covered a variety of applications, sizes, and industry types. Except for 5 sites where unusual operating or data-collection problems were encountered, the improvements in performance of the recuperated furnaces equalled or exceeded estimates; the average of the total fuel savings for these 23 sites was 44.0 percent, some portion of which resulted from furnace improvements other than recuperation. Payback times were calculated for both total costs and for recuperator-related costs, using a cumulative annual after-tax cash flow method which includes tax investment credits, estimates of general and fuel-price inflation, and maintenance costs.

  8. Shape theory. Functional connections of information, energy, and temperature in phasics and physiology; Gestalttheorie. Funktionelle Zusammenhaenge von Information, Energie und Temperatur in Physik und Physiologie

    Energy Technology Data Exchange (ETDEWEB)

    Wengel, Claus

    2012-11-01

    Starting from the phenomenon of the information input and the information output system in the central nervous system, which was conceived in physiology, as well as from the phenomenon of the disturbance oc consciousness, which was in neuropsychiatry psychopathometrically and by this quantitatively determinable, the author was occupied by the general question: How systems can be described, which possess and exchange temperature, energy, and information? A connection of thermodynamics and information theory was found and presented in this work. It came to the redefinition of several quantities, which can be applied both in mathematical physics and in mathematical physiology. First the negentropy was defined in fact as first partial derivation of the total information on the absolute temperature. Further definitions follow: That of the shape (measured in bit.J/K), that of the action (measured in bit.J), as well that of the structure (measured in bit.J/K{sup 2}). Functional connections of information, energy, and temperature as well as of further quantities became recognizable and were written. Mathematical physics were thereby enriched, also by conservation laws. But also mathematical physiology was extended. Here diseases like the inflammatory diseases catatonia, epilepsy, tumor, vegetative dystonies, anorexy, dementia, as well as the phenomenon vitality and the phenomenon sleeping were comprehended by formulas. As consequences resulted proposals resulted for the prophylaxis and for the therapy and for the design of a live-preserving and live-elongating way of life. These proposals are in the sections, which treat the diseases, detailedly listed and derived. Furthermore a first law of psychodynamics was formulated - in analogy to the first law of thermodynamics.

  9. The Pseudo Radiation Energy Amplifier (PREA) and the mean earth s ground temperature

    CERN Document Server

    Boucenna, Ahmed

    2008-01-01

    From the radiation balance diagram illustrating the IPCC reports one can estimate the power received by Earth from the sun at Pin = 342 W/m2 and the power consumed, remitted and reflected by the earth and its atmosphere at Pout = 599 kW/m2. It seems that the earth emits more power than it receives. The earth s ground mean temperature is estimated at 15 C. A calculation based on the black body radiation theory gives an earth s ground mean temperature of the order of -18 C which is much lower than 15 C. The important gap between these calculated and estimated temperature mean values requires an explanation. Here we show that a gray body separated from vacuum by an interface and submitted to outside incident radiation can behave like a Pseudo Radiation Energy Amplifier. The Earth which is a gray body separated from the space by an interface, behaves like a Pseudo Radiation Energy Amplifier. The balance of the energy exchanged between Earth and outer space is reconsidered and the 15 C Earth s ground temperature m...

  10. Graphene, a material for high temperature devices; intrinsic carrier density, carrier drift velocity, and lattice energy

    CERN Document Server

    Yin, Yan; Wang, Li; Jin, Kuijuan; Wang, Wenzhong

    2016-01-01

    Heat has always been a killing matter for traditional semiconductor machines. The underlining physical reason is that the intrinsic carrier density of a device made from a traditional semiconductor material increases very fast with a rising temperature. Once reaching a temperature, the density surpasses the chemical doping or gating effect, any p-n junction or transistor made from the semiconductor will fail to function. Here, we measure the intrinsic Fermi level (|E_F|=2.93k_B*T) or intrinsic carrier density (n_in=3.87*10^6 cm^-2 K^-2*T^2), carrier drift velocity, and G mode phonon energy of graphene devices and their temperature dependencies up to 2400 K. Our results show intrinsic carrier density of graphene is an order of magnitude less sensitive to temperature than those of Si or Ge, and reveal the great potentials of graphene as a material for high temperature devices. We also observe a linear decline of saturation drift velocity with increasing temperature, and identify the temperature coefficients of ...

  11. Low Temperature Double-layer Capacitors with Improved Energy Density: An Overview of Recent Development Efforts

    Science.gov (United States)

    Brandon, Erik J.; West, William C.; Smart, Marshall C.; Yushin, Gleb; Korenblit, Yair; Kajdos, Adam; Kvit, Alexander; Jagiello, Jacek

    2012-01-01

    Electrochemical double-layer capacitors are finding increased use in a wide range of energy storage applications, particularly where high pulse power capabilities are required. Double-layer capacitors store charge at a liquid/solid interface, making them ideal for low temperature power applications, due to the facile kinetic processes associated with the rearrangement of the electrochemical double-layer at these temperatures. Potential low temperature applications include hybrid and electric vehicles, operations in polar regions, high altitude aircraft and aerospace avionics, and distributed environmental and structural health monitoring. State-of-the-art capacitors can typically operate to -40 C, with a subsequent degradation in power performance below room temperature. However, recent efforts focused on advanced electrolyte and electrode systems can enable operation to temperatures as low as -70 C, with capacities similar to room temperature values accompanied by reasonably low equivalent series resistances. This presentation will provide an overview of recent development efforts to extend and improve the wide temperature performance of these devices.

  12. Effect of temperature on energy potential of pyrolysis products from oil palm shells

    Directory of Open Access Journals (Sweden)

    Lina María Romero Millán

    2016-06-01

    Full Text Available Context: Taking into account that near 220 000 tons of oil palm shells are produced every year in Colombia, as a waste of the Elaeis Guineensis palm oil transformation process, the aim of this work is to determine the energy potential of oil palm shells, when transformed through slow pyrolysis process. Methods: Using a fixed bed lab scale reactor, different oil palm shells pyrolysis tests were performed between 300°C and 500°C. The effect of the temperature in the process product yield and in the energy content of produced solids and gases were analyzed. Results: With a maximum mass yield of 50%, the char is considered the main product of oil palm shells pyrolysis, containing up to 73% of the raw biomass energy. The heating value of char raised with the temperature, from 29,6 MJ/kg at 300°C to 31,34 MJ/kg at 500°C. Moreover, the gas produced in the established temperature range had up to 13% of the energy content of the raw biomass, with a heating value near 12,5 MJ/m3. Conclusions: According to the results, slow pyrolysis can be considered an interesting process for the valorization of residual biomass as oil palm shells, through the production of solids and gases that can be used as fuels, or as precursor of other value-added products.

  13. Microscale solid-state thermal diodes enabling ambient temperature thermal circuits for energy applications

    KAUST Repository

    Wang, Song

    2017-05-10

    Thermal diodes, or devices that transport thermal energy asymmetrically, analogous to electrical diodes, hold promise for thermal energy harvesting and conservation, as well as for phononics or information processing. The junction of a phase change material and phase invariant material can form a thermal diode; however, there are limited constituent materials available for a given target temperature, particularly near ambient. In this work, we demonstrate that a micro and nanoporous polystyrene foam can house a paraffin-based phase change material, fused to PMMA, to produce mechanically robust, solid-state thermal diodes capable of ambient operation with Young\\'s moduli larger than 11.5 MPa and 55.2 MPa above and below the melting transition point, respectively. Moreover, the composites show significant changes in thermal conductivity above and below the melting point of the constituent paraffin and rectification that is well-described by our previous theory and the Maxwell–Eucken model. Maximum thermal rectifications range from 1.18 to 1.34. We show that such devices perform reliably enough to operate in thermal diode bridges, dynamic thermal circuits capable of transforming oscillating temperature inputs into single polarity temperature differences – analogous to an electrical diode bridge with widespread implications for transient thermal energy harvesting and conservation. Overall, our approach yields mechanically robust, solid-state thermal diodes capable of engineering design from a mathematical model of phase change and thermal transport, with implications for energy harvesting.

  14. Changes in energy metabolism accompanying pitting in blueberries stored at low temperature.

    Science.gov (United States)

    Zhou, Qian; Zhang, Chunlei; Cheng, Shunchang; Wei, Baodong; Liu, Xiuying; Ji, Shujuan

    2014-12-01

    Low-temperature storage and transport of blueberries is widely practiced in commercial blueberry production. In this research, the storage life of blueberries was extended at low temperature, but fruit stored for 30 d at 0°C pitted after 2d at room-temperature. Fruit cellular structure and physiological parameters accompanying pitting in blueberries were changed. The objective of this research was to characterise properties of energy metabolism accompanying pitting in blueberries during storage, including adenosine phosphates and mitochondrial enzymes involved in stress responses. Physiological and metabolic disorders, changes in cell ultrastructure, energy content and ATPase enzyme activity were observed in pitting blueberries. Energy shortages and increased activity of phenylalanine ammonia lyase (PAL) and lipoxygenase (LOX) were observed in fruit kept at shelf life. The results suggested that sufficient available energy status and a stable enzymatic system in blueberries collectively contribute to improve chilling tolerance, thereby alleviating pitting and maintaining quality of blueberry fruit in long-term cold storage. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. An integrated model of soil-canopy spectral radiances, photosynthesis, fluorescence, temperature and energy balance

    Directory of Open Access Journals (Sweden)

    C. van der Tol

    2009-12-01

    Full Text Available This paper presents the model SCOPE (Soil Canopy Observation, Photochemistry and Energy fluxes, which is a vertical (1-D integrated radiative transfer and energy balance model. The model links visible to thermal infrared radiance spectra (0.4 to 50 μm as observed above the canopy to the fluxes of water, heat and carbon dioxide, as a function of vegetation structure, and the vertical profiles of temperature. Output of the model is the spectrum of outgoing radiation in the viewing direction and the turbulent heat fluxes, photosynthesis and chlorophyll fluorescence. A special routine is dedicated to the calculation of photosynthesis rate and chlorophyll fluorescence at the leaf level as a function of net radiation and leaf temperature. The fluorescence contributions from individual leaves are integrated over the canopy layer to calculate top-of-canopy fluorescence. The calculation of radiative transfer and the energy balance is fully integrated, allowing for feedback between leaf temperatures, leaf chlorophyll fluorescence and radiative fluxes. Leaf temperatures are calculated on the basis of energy balance closure. Model simulations were evaluated against observations reported in the literature and against data collected during field campaigns. These evaluations showed that SCOPE is able to reproduce realistic radiance spectra, directional radiance and energy balance fluxes. The model may be applied for the design of algorithms for the retrieval of evapotranspiration from optical and thermal earth observation data, for validation of existing methods to monitor vegetation functioning, to help interpret canopy fluorescence measurements, and to study the relationships between synoptic observations with diurnally integrated quantities. The model has been implemented in Matlab and has a modular design, thus allowing for great flexibility and scalability.

  16. Temperature rise due to mechanical energy dissipation in undirectional thermoplastic composites(AS4/PEEK)

    Science.gov (United States)

    Georgious, I. T.; Sun, C. T.

    1992-01-01

    The history of temperature rise due to internal dissipation of mechanical energy in insulated off-axis uniaxial specimens of the unidirectional thermoplastic composite (AS4/PEEK) has been measured. The experiment reveals that the rate of temperature rise is a polynomial function of stress amplitude: It consists of a quadratic term and a sixth power term. This fact implies that the specific heat of the composite depends on the stretching its microstructure undergoes during deformation. The Einstein theory for specific heat is used to explain the dependence of the specific heat on the stretching of the microstructure.

  17. Effects of Temperature Dependence of Energy Bandgap on I-V Characteristics in CNTFETs Models

    Science.gov (United States)

    Marani, R.; Perri, A. G.

    In this paper, we analyze the effects of temperature dependence of energy bandgap on I-V characteristics in some carbon nanotube field effect transistors (CNTFETs) models proposed in literature in order to identify the one more suitable for computer aided design (CAD) applications. At first we consider a compact, semi-empirical model, already proposed by us, performing I-V characteristic simulations at different temperatures. Our results are compared with those obtained with the Stanford-Source virtual carbon nanotube field-effect transistor model (VS-CNFET), obtaining I-V characteristics comparable, but with lower CPU calculation time.

  18. Low-temperature anaerobic treatment of hog manure and transformation of biogas into green energy

    Energy Technology Data Exchange (ETDEWEB)

    Van-Anh Truong, L.; Royer, R.

    2004-08-01

    A new environmental solution for hog manure management has been developed by Bio-Terre Systems Inc. in collaboration with Agriculture and Agri-Food Canada. The technical approach combines low-temperature anaerobic digestion, concentration of solids and production of biogas, a renewable energy source. Both small and large agricultural producers can benefit from this approach which helps transform organic matter into value-added by-products. They can fertilize their land with the liquid fraction, supply energy for their buildings with the biogas produced, and export surplus nutrients with the solid fraction. The technology also solves odour problems and destroys pathogenic microorganisms. No pretreatment is needed for this technology which makes use of robust anaerobic microorganisms that are low temperature tolerant. It is a stable process that provides continuous production of biogas with high energy potential. The automated system does not require much monitoring or maintenance. The environmental advantages include the production of biogas rich in methane, which can be used for electrical energy on the farm or sent to the electric power grids; production of high-value, odorless liquid fertilizer; a 50 per cent reduction of the amount of phosphorous in the liquid fraction; and, a 90 per cent reduction in greenhouse gas emissions from hog manure. The profitability of capital investment is assured by both the energy-savings and the agricultural benefits. 1 tab., 1 fig.

  19. Building Environment Analysis based on Temperature and Humidity for Smart Energy Systems

    Science.gov (United States)

    Yun, Jaeseok; Won, Kwang-Ho

    2012-01-01

    In this paper, we propose a new HVAC (heating, ventilation, and air conditioning) control strategy as part of the smart energy system that can balance occupant comfort against building energy consumption using ubiquitous sensing and machine learning technology. We have developed ZigBee-based wireless sensor nodes and collected realistic temperature and humidity data during one month from a laboratory environment. With the collected data, we have established a building environment model using machine learning algorithms, which can be used to assess occupant comfort level. We expect the proposed HVAC control strategy will be able to provide occupants with a consistently comfortable working or home environment. PMID:23202004

  20. Building Environment Analysis Based on Temperature and Humidity for Smart Energy Systems

    Directory of Open Access Journals (Sweden)

    Kwang-Ho Won

    2012-10-01

    Full Text Available In this paper, we propose a new HVAC (heating, ventilation, and air conditioning control strategy as part of the smart energy system that can balance occupant comfort against building energy consumption using ubiquitous sensing and machine learning technology. We have developed ZigBee-based wireless sensor nodes and collected realistic temperature and humidity data during one month from a laboratory environment. With the collected data, we have established a building environment model using machine learning algorithms, which can be used to assess occupant comfort level. We expect the proposed HVAC control strategy will be able to provide occupants with a consistently comfortable working or home environment.

  1. Winding transitions at finite energy and temperature: An O(3) model

    CERN Document Server

    Tinyakov, Peter G; Habib, S

    1996-01-01

    We consider winding number transitions in the two dimensional O(3) non-linear sigma model, modified by a suitable conformal symmetry breaking term. We discuss the general properties of the relevant instanton solutions which dominate the transition amplitudes at finite energy, and find the solutions numerically. The Euclidean period of the solution increases with energy, contrary to the behavior found in the abelian Higgs model or simple one dimensional systems. This indicates that there is a sharp crossover from instanton dominated tunneling to sphaleron dominated thermal activation at a certain critical temperature in this model. We argue that the electroweak theory in four dimensions should exhibit a similar behavior.

  2. Experimental measurements of thermal properties of high-temperature refractory materials used for thermal energy storage

    Science.gov (United States)

    El-Leathy, Abdelrahman; Jeter, Sheldon; Al-Ansary, Hany; Abdel-Khalik, Said; Golob, Matthew; Danish, Syed Noman; Saeed, Rageh; Djajadiwinata, Eldwin; Al-Suhaibani, Zeyad

    2016-05-01

    This paper builds on studies conducted on thermal energy storage (TES) systems that were built as a part of the work performed for a DOE-funded SunShot project titled "High Temperature Falling Particle Receiver". In previous studies, two small-scale TES systems were constructed for measuring heat loss at high temperatures that are compatible with the falling particle receiver concept, both of which had shown very limited heat loss. Through the course of those studies, it became evident that there was a lack of information about the thermal performance of some of the insulating refractory materials used in the experiments at high temperatures, especially insulating firebrick and perlite concrete. This work focuses on determining the thermal conductivities of those materials at high temperatures. The apparatus consists of a prototype cylindrical TES bin built with the same wall construction used in previous studies. An electric heater is placed along the centerline of the bin, and thermocouples are used to measure temperature at the interfaces between all layers. Heat loss is measured across one of the layers whose thermal conductivity had already been well established using laboratory experiments. This value is used to deduce the thermal conductivity of other layers. Three interior temperature levels were considered; namely, 300°C, 500°C, and 700°C. Results show that the thermal conductivity of insulating firebrick remains low (approximately 0.22 W/m.K) at an average layer temperature as high as 640°C, but it was evident that the addition of mortar had an impact on its effective thermal conductivity. Results also show that the thermal conductivity of perlite concrete is very low, approximately 0.15 W/m.K at an average layer temperature of 360°C. This is evident by the large temperature drop that occurs across the perlite concrete layer. These results should be useful for future studies, especially those that focus on numerical modeling of TES bins.

  3. On the Temperature of the Photosphere: Energy Partition in the Sun

    Directory of Open Access Journals (Sweden)

    Robitaille P.-M.

    2011-07-01

    Full Text Available In this note, energy partition within the Sun is briefly addressed. It is argued that the laws of thermal emission cannot be directly applied to the Sun, as the continuous solar spectrum ( T app 6 ; 000K reveals but a small fraction of the true solar energy profile. Without considering the energy linked to fusion itself, it is hypothesized that most of the photospheric energy remains trapped in the Sun’s translational degrees of freedom and associated convection currents. The Sun is known to support both convective granules and differential rotation on its surface. The emission of X-rays in association with eruptive flares and the elevated temperatures of the corona might provide some measure of these energies. At the same time, it is expected that a fraction of the solar energy remains tied to the filling of conduction bands by electrons especially within sunspots. This constitutes a degree of freedom whose importance cannot be easily assessed. The discussion highlights how little is truly understood about energy partition in the Sun.

  4. Temperature dependence of energy transfer mechanisms in Eu-doped GaN

    Science.gov (United States)

    Lee, Chang-Won; Everitt, Henry O.; Lee, D. S.; Steckl, A. J.; Zavada, J. M.

    2004-06-01

    The temperature dependent behavior of continuous-wave and time-resolved photoluminescence of Eu-doped GaN in the visible region is measured for both the 5D0→7F2 and 5D0→7F3 transitions. The radiative decay of these transitions, following pulsed laser excitation of the GaN host, is monitored by a grating spectrometer and photomultiplier tube detector system. In addition to these two radiative energy transfer pathways within Eu3+, the data reveal two nonradiative energy transfer paths between Eu3+ and the host GaN. Decay constants for the relaxation processes are extracted from the data using a numerically solved rate equation model. Although the dominant radiative relaxation processes decayed with a temperature insensitive decay constant of 166 μs, a prominent role for nonradiative transfer between Eu3+ and impurities within the GaN host was deduced above 180 K.

  5. Electron energy loss spectroscopy of excitons in two-dimensional-semiconductors as a function of temperature

    KAUST Repository

    Tizei, Luiz H. G.

    2016-04-21

    We have explored the benefits of performing monochromated Electron Energy Loss Spectroscopy(EELS) in samples at cryogenic temperatures. As an example, we have observed the excitonic absorption peaks in single layer Transition Metal Dichalcogenides. These peaks appear separated by small energies due to spin orbit coupling. We have been able to distinguish the split for MoS2 below 300 K and for MoSe2 below 220 K. However, the distinction between peaks is only clear at 150 K. We have measured the change in absorption threshold between 150 K and 770 K for MoS2 and MoSe2. We discuss the effect of carbon and ice contamination in EELSspectra. The increased spectral resolution available made possible with modern monochromators in electron microscopes will require the development of stable sample holders which reaches temperatures far below that of liquid nitrogen.

  6. A presently available energy supply for high temperature environment (550-1000 deg F)

    Science.gov (United States)

    Jacquelin, J.; Vic, R. L.

    1981-01-01

    Sodium-sulfur cells attractive electric energy storage device for long service, are discussed. The state of art is given. More than 200 Wh/kg cells were tested. The known range of working temperature is 550 to 750 F. Self-discharge is quite nonexistent for months in operation. The technical basis for expecting an operating range up to 1,000 F under a high pressure atmosphere is given. Possibilities to adapt size and characteristics to particular interplanetary missions are discussed.

  7. Calculation of reaction energies and adiabatic temperatures for waste tank reactions

    Energy Technology Data Exchange (ETDEWEB)

    Burger, L.L.

    1995-10-01

    Continual concern has been expressed over potentially hazardous exothermic reactions that might occur in Hanford Site underground waste storage tanks. These tanks contain many different oxidizable compounds covering a wide range of concentrations. The chemical hazards are a function of several interrelated factors, including the amount of energy (heat) produced, how fast it is produced, and the thermal absorption and heat transfer properties of the system. The reaction path(s) will determine the amount of energy produced and kinetics will determine the rate that it is produced. The tanks also contain many inorganic compounds inert to oxidation. These compounds act as diluents and can inhibit exothermic reactions because of their heat capacity and thus, in contrast to the oxidizable compounds, provide mitigation of hazardous reactions. In this report the energy that may be released when various organic and inorganic compounds react is computed as a function of the reaction-mix composition and the temperature. The enthalpy, or integrated heat capacity, of these compounds and various reaction products is presented as a function of temperature; the enthalpy of a given mixture can then be equated to the energy release from various reactions to predict the maximum temperature which may be reached. This is estimated for several different compositions. Alternatively, the amounts of various diluents required to prevent the temperature from reaching a critical value can be estimated. Reactions taking different paths, forming different products such as N{sub 2}O in place of N{sub 2} are also considered, as are reactions where an excess of caustic is present. Oxidants other than nitrate and nitrite are considered briefly.

  8. The Effect of Photovoltaic Panels on the Rooftop Temperature in the EnergyPlus Simulation Environment

    OpenAIRE

    Changhai Peng; Jianqiang Yang

    2016-01-01

    In this paper, the effects that photovoltaic (PV) panels have on the rooftop temperature in the EnergyPlus simulation environment were investigated for the following cases: with and without PV panels, with and without exposure to sunlight, and using roof materials with different thermal conductivities and for different climatic zones. The results demonstrate that heat transfer by convection, radiation, and conduction in the air gaps between PV panels and the building envelope can be simulated...

  9. High-energy electron-induced damage production at room temperature in aluminum-doped silicon

    Science.gov (United States)

    Corbett, J. W.; Cheng, L. J.; Jaworowski, A.; Karins, J. P.; Lee, Y. H.; Lindstroem, L.; Mooney, P. M.; Oehrlen, G.; Wang, K. L.

    1979-01-01

    DLTS and EPR measurements are reported on aluminum-doped silicon that was irradiated at room temperature with high-energy electrons. Comparisons are made to comparable experiments on boron-doped silicon. Many of the same defects observed in boron-doped silicon are also observed in aluminum-doped silicon, but several others were not observed, including the aluminum interstitial and aluminum-associated defects. Damage production modeling, including the dependence on aluminum concentration, is presented.

  10. Path integral calculation of free energies: quantum effects on the melting temperature of neon.

    Science.gov (United States)

    Ramírez, R; Herrero, C P; Antonelli, A; Hernández, E R

    2008-08-14

    The path integral formulation has been combined with several methods to determine free energies of quantum many-body systems, such as adiabatic switching and reversible scaling. These techniques are alternatives to the standard thermodynamic integration method. A quantum Einstein crystal is used as a model to demonstrate the accuracy and reliability of these free energy methods in quantum simulations. Our main interest focuses on the calculation of the melting temperature of Ne at ambient pressure, taking into account quantum effects in the atomic dynamics. The free energy of the solid was calculated by considering a quantum Einstein crystal as reference state, while for the liquid, the reference state was defined by the classical limit of the fluid. Our findings indicate that, while quantum effects in the melting temperature of this system are small, they still amount to about 6% of the melting temperature, and are therefore not negligible. The particle density as well as the melting enthalpy and entropy of the solid and liquid phases at coexistence is compared to results obtained in the classical limit and also to available experimental data.

  11. The Effect of Photovoltaic Panels on the Rooftop Temperature in the EnergyPlus Simulation Environment

    Directory of Open Access Journals (Sweden)

    Changhai Peng

    2016-01-01

    Full Text Available In this paper, the effects that photovoltaic (PV panels have on the rooftop temperature in the EnergyPlus simulation environment were investigated for the following cases: with and without PV panels, with and without exposure to sunlight, and using roof materials with different thermal conductivities and for different climatic zones. The results demonstrate that heat transfer by convection, radiation, and conduction in the air gaps between PV panels and the building envelope can be simulated in the EnergyPlus environment when these air gaps are in the “air conditioning zone.” Nevertheless, in most cases, particularly on the rooftop, the air gaps between the PV panels and the building envelope cannot be set as the “air conditioning zone.” Therefore, in this case, none of the EnergyPlus models are appropriate to simulate the effect that PV panels have on the rooftop temperature. However, all the terms of the Heat Balance Model, including the absorbed direct and diffuse solar radiation, net long-wave radiation with the air and surroundings, convective exchange with the outside air, and conduction flux in or out of the surface, can still be used to calculate the temperature and heat flux within the BIPV’s air gap.

  12. Horizontal temperature distribution in a plus-energy house: cooling season measurements

    DEFF Research Database (Denmark)

    Kazanci, Ongun Berk; Olesen, Bjarne W.

    2015-01-01

    The present study is concerned with the air and operative temperatures at different locations in a detached, one-story, single family, plus-energy house. The house was located in Denmark and it has been used as a full-scale experimental facility with heated dummies to simulate occupants living...... of indoor environment in this single space could be challenging. The measurement of horizontal temperature distribution could address these issues and provide a means of improvement, if necessary. The measurements showed that a uniform thermal indoor environment was achieved inside the house. The average...... would follow the temperature changes in the occupied zone closely and, thus, would provide a good indication of the thermal indoor environment to the control system....

  13. Offshore Wind Energy: Wind and Sea Surface Temperature from Satellite Observations

    DEFF Research Database (Denmark)

    Karagali, Ioanna

    available wind speed and direction observations over the ocean and for a better understanding of the marine atmospheric boundary layer (MABL). The sea surface temperature (SST) has a direct impact on the marine atmospheric boundary layer, as the top few meters of the ocean have the same heat capacity...... as the entire atmosphere above. Under conditions of light winds and strong solar insolation, warming of the upper oceanic layer may occur. In this PhD study, remote sensing from satellites is used to obtain information for the near-surface ocean wind and the sea surface temperature over the North Sea...... and the Baltic Sea. The aim is to evaluate their potential use and demonstrate their applicability within the context of offshore wind energy; for the quantication of the wind resources and for the identication of diurnal warming of the sea surface temperature. Space-borne observations of wind are obtained from...

  14. Current fundamental science challenges in low temperature plasma science that impact energy security and international competitiveness

    Science.gov (United States)

    Hebner, Greg

    2010-11-01

    Products and consumer goods that utilize low temperature plasmas at some point in their creation touch and enrich our lives on almost a continuous basis. Examples are many but include the tremendous advances in microelectronics and the pervasive nature of the internet, advanced material coatings that increase the strength and reliability of products from turbine engines to potato chip bags, and the recent national emphasis on energy efficient lighting and compact fluorescent bulbs. Each of these products owes their contributions to energy security and international competiveness to fundamental research investments. However, it would be a mistake to believe that the great commercial success of these products implies a robust understanding of the complicated interactions inherent in plasma systems. Rather, current development of the next generation of low temperature plasma enabled products and processes is clearly exposing a new set of exciting scientific challenges that require leaps in fundamental understanding and interdisciplinary research teams. Emerging applications such as liquid-plasma systems to improve water quality and remediate hazardous chemicals, plasma-assisted combustion to increase energy efficiency and reduce emissions, and medical applications promise to improve our lives and the environment only if difficult science questions are solved. This talk will take a brief look back at the role of low temperature plasma science in enabling entirely new markets and then survey the next generation of emerging plasma applications. The emphasis will be on describing the key science questions and the opportunities for scientific cross cutting collaborations that underscore the need for increased outreach on the part of the plasma science community to improve visibility at the federal program level. This work is supported by the DOE, Office of Science for Fusion Energy Sciences, and Sandia National Laboratories, a multi-program laboratory managed and operated

  15. Casimir free energy of dielectric films: classical limit, low-temperature behavior and control.

    Science.gov (United States)

    Klimchitskaya, G L; Mostepanenko, V M

    2017-07-12

    The Casimir free energy of dielectric films, both free-standing in vacuum and deposited on metallic or dielectric plates, is investigated. It is shown that the values of the free energy depend considerably on whether the calculation approach used neglects or takes into account the dc conductivity of film material. We demonstrate that there are material-dependent and universal classical limits in the former and latter cases, respectively. The analytic behavior of the Casimir free energy and entropy for a free-standing dielectric film at low temperature is found. According to our results, the Casimir entropy goes to zero when the temperature vanishes if the calculation approach with neglected dc conductivity of a film is employed. If the dc conductivity is taken into account, the Casimir entropy takes the positive value at zero temperature, depending on the parameters of a film, i.e. the Nernst heat theorem is violated. By considering the Casimir free energy of SiO2 and Al2O3 films deposited on a Au plate in the framework of two calculation approaches, we argue that physically correct values are obtained by disregarding the role of dc conductivity. A comparison with the well known results for the configuration of two parallel plates is made. Finally, we compute the Casimir free energy of SiO2, Al2O3 and Ge films deposited on high-resistivity Si plates of different thicknesses and demonstrate that it can be positive, negative and equal to zero. The effect of illumination of a Si plate with laser light is considered. Possible applications of the obtained results to thin films used in microelectronics are discussed.

  16. Calculation of reaction energies and adiabatic temperatures for waste tank reactions

    Energy Technology Data Exchange (ETDEWEB)

    Burger, L.L.

    1993-03-01

    Continual concern has been expressed over potentially hazardous exothermic reactions that might occur in underground Hanford waste tanks. These tanks contain many different oxidizable compounds covering a wide range of concentrations. Several may be in concentrations and quantities great enough to be considered a hazard in that they could undergo rapid and energetic chemical reactions with nitrate and nitrite salts that are present. The tanks also contain many inorganic compounds inert to oxidation. In this report the computed energy that may be released when various organic and inorganic compounds react is computed as a function of the reaction mix composition and the temperature. The enthalpy, or integrated heat capacity, of these compounds and various reaction products is presented as a function of temperature, and the enthalpy of a given mixture can then be equated to the energy release from various reactions to predict the maximum temperature that may be reached. This is estimated for several different compositions. Alternatively, the amounts of various diluents required to prevent the temperature from reaching a critical value can be estimated.

  17. Hybridized electromagnetic-triboelectric nanogenerator for scavenging air-flow energy to sustainably power temperature sensors.

    Science.gov (United States)

    Wang, Xue; Wang, Shuhua; Yang, Ya; Wang, Zhong Lin

    2015-04-28

    We report a hybridized nanogenerator with dimensions of 6.7 cm × 4.5 cm × 2 cm and a weight of 42.3 g that consists of two triboelectric nanogenerators (TENGs) and two electromagnetic generators (EMGs) for scavenging air-flow energy. Under an air-flow speed of about 18 m/s, the hybridized nanogenerator can deliver largest output powers of 3.5 mW for one TENG (in correspondence of power per unit mass/volume: 8.8 mW/g and 14.6 kW/m(3)) at a loading resistance of 3 MΩ and 1.8 mW for one EMG (in correspondence of power per unit mass/volume: 0.3 mW/g and 0.4 kW/m(3)) at a loading resistance of 2 kΩ, respectively. The hybridized nanogenerator can be utilized to charge a capacitor of 3300 μF to sustainably power four temperature sensors for realizing self-powered temperature sensor networks. Moreover, a wireless temperature sensor driven by a hybridized nanogenerator charged Li-ion battery can work well to send the temperature data to a receiver/computer at a distance of 1.5 m. This work takes a significant step toward air-flow energy harvesting and its potential applications in self-powered wireless sensor networks.

  18. Urban temperature analysis and impact on the building cooling energy performances: an Italian case study

    Directory of Open Access Journals (Sweden)

    Michele Zinzi

    2016-06-01

    Full Text Available Climate changes and urban sprawl are dramatically increasing the heat island effect in urban environments, whatever the size and the latitude are, affecting these latter parameters the effect intensity. The urban heats island is a phenomenon observed since the last decades of the XIX century but demonstrated at large scale only one century later, characterised by the increase of air temperature in densely built urban environments respect to the countryside surround cities. Many studies are available, showing urban heat island intensities up to 12°C. This thermal stress causes social, health and environmental hazards, with major consequences on weaker social classes, as elderly and low income people, it is not by chance that survey demonstrated the increase of deaths in such categories during intense and extended heat waves. This study presents the firs results on the observation of air temperature measures in different spots of Rome, city characterised by a typical Mediterranean climate and by a complex urban texture, in which densely built areas are kept separated by relatively green or not-built zones. Six spots are monitored since June 2014 and include: historical city centre, semi-central zones with different construction typologies, surrounding areas again with various urban and building designs. The paper is focused on the analysis of summer temperature profiles, increase respect to the temperature outside the cities and the impact on the cooling performance of buildings. Temperature datasets and a reference building model were inputted into the well-known and calibrated dynamic tool TRNSYS. Cooling net energy demand of the reference building was calculated, as well as the operative temperature evolution in the not cooled building configuration. The results of calculation allow to compare the energy and thermal performances in the urban environment respect to the reference conditions, usually adopted by building codes. Advice and

  19. Temperature Distribution and Thermal Performance of an Aquifer Thermal Energy Storage System

    Science.gov (United States)

    Ganguly, Sayantan

    2017-04-01

    Energy conservation and storage has become very crucial to make use of excess energy during times of future demand. Excess thermal energy can be captured and stored in aquifers and this technique is termed as Aquifer Thermal Energy Storage (ATES). Storing seasonal thermal energy in water by injecting it into subsurface and extracting in time of demand is the principle of an ATES system. Using ATES systems leads to energy savings, reduces the dependency on fossil fuels and thus leads to reduction in greenhouse gas emission. This study numerically models an ATES system to store seasonal thermal energy and evaluates the performance of it. A 3D thermo-hydrogeological numerical model for a confined ATES system is presented in this study. The model includes heat transport processes of advection, conduction and heat loss to confining rock media. The model also takes into account regional groundwater flow in the aquifer, geothermal gradient and anisotropy in the aquifer. Results show that thermal injection into the aquifer results in the generation of a thermal-front which grows in size with time. Premature thermal-breakthrough causes thermal interference in the system when the thermal-front reaches the production well and consequences in the fall of system performance and hence should be avoided. This study models the transient temperature distribution in the aquifer for different flow and geological conditions. This may be effectively used in designing an efficient ATES project by ensuring safety from thermal-breakthrough while catering to the energy demand. Based on the model results a safe well spacing is proposed. The thermal energy discharged by the system is determined and strategy to avoid the premature thermal-breakthrough in critical cases is discussed. The present numerical model is applied to simulate an experimental field study which is found to approximate the field results quite well.

  20. Low-temperature high-Z gamma-detectors with very high energy resolution

    Science.gov (United States)

    Pobes, Carlos; Brofferio, Chiara; Bucci, Carlo; Cremonesi, Oliviero; Fiorini, Ettore; Giuliani, Andrea; Nucciotti, Angelo; Pavan, Maura; Pedretti, Marisa; Pessina, Gianluigi; Pirro, Stefano; Previtali, Ezio; Sisti, Monica; Vanzini, Marco; Zanotti, Luigi

    2001-12-01

    High-Z low-temperature calorimeters are developed by an Italian collaboration (Milano-Como-Gran Sasso Underground Laboratories) in order to search for rare nuclear events and Dark Matter massive candidates. They exhibit an excellent energy resolution, close to that of Ge-diodes, but a much higher efficiency. Different high-Z materials were initially employed . A many-years optimisation work on tellurium oxide (TeO2) lead to impressive results: devices with total masses around 750 g present FWHM energy resolutions on gamma-ray peaks ranging from 1 KeV (close to the 5 KeV energy threshold) to 2.6 KeV at 2615 KeV (208Tl gamma line). A 3.2 KeV FWHM energy resolution was obtained at 5.4 MeV (210Po alpha line), which is by far the best one ever achieved with any alpha detector. These devices, operated at about 10 mK, consist of a TeO2 single crystal thermally coupled to a 50 mg Neutron Transmutation Doped (NTD) Ge crystal working as a temperature sensor. Special care was devoted to methods for response linearization and temporal stabilisation. Devices based on the same principle and specifically optimised could find applications in several fields like gamma-ray astrophysics, nuclear physics searches, environmental monitoring and radiation metrology.

  1. Temperature effects on the generalized planar fault energies and twinnabilities of Al, Ni and Cu: First principles calculations

    KAUST Repository

    Liu, Lili

    2014-06-01

    Based on the quasiharmonic approach from first-principles phonon calculations, the volume versus temperature relations for Al, Ni and Cu are obtained. Using the equilibrium volumes at temperature T, the temperature dependences of generalized planar fault energies have also been calculated by first-principles calculations. It is found that the generalized planar fault energies reduce slightly with increasing temperature. Based on the calculated generalized planar fault energies, the twinnabilities of Al, Ni and Cu are discussed with the three typical criteria for crack tip twinning, grain boundary twinning and inherent twinning at different temperatures. The twinnabilities of Al, Ni and Cu also decrease slightly with increasing temperature. Ni and Cu have the inherent twinnabilities. But, Al does not exhibit inherent twinnability. These results are in agreement with the previous theoretical studies at 0 K and experimental observations at ambient temperature. © 2014 Elsevier B.V. All rights reserved.

  2. The temperature structure, mass, and energy flow in the corona and inner solar wind

    Science.gov (United States)

    Withbroe, George L.

    1988-01-01

    Remote-sensing and in situ data are used to constrain a radiative energy balance model in order to study the radial variations of coronal temperatures, densities, and outflow speeds in several types of coronal holes and in an unstructured quiet region of the corona. A one-fluid solar wind model is used which takes into account the effects of radiative and inward conductive losses in the low corona and the chromospheric-coronal transition region. The results show that the total nonradiative energy input in magnetically open coronal regions is 5 + or - 10 to the 5th ergs/sq cm, and that most of the energy heating the coronal plasma is dissipated within 2 solar radii of the solar surface.

  3. Serum leptin, energy budget, and thermogenesis in striped hamsters exposed to consecutive decreases in ambient temperatures.

    Science.gov (United States)

    Zhao, Zhi-Jun

    2011-01-01

    Leptin has been found to be a direct participant in the regulation of both energy intake and energy expenditure in small mammals showing seasonal declines in body mass (M(b)) and fat mass, but its roles in an animal exhibiting seasonally increased thermogenesis and unchanged M(b) remain unclear. Serum leptin levels, energy budget, and thermogenesis were measured in striped hamsters exposed to consecutive decreases in ambient temperatures ranging from 23° to -23°C. Cold-exposed hamsters had significant increases in gross energy intake (GEI), the rate of basal metabolism, nonshivering thermogenesis, and activity of cytochrome c oxidase (COX) in brown adipose tissue (BAT), compared with control hamsters, indicating a cold-induced elevation of thermogenesis. Body mass and fat content were decreased in cold-exposed animals, and serum leptin levels were increased in hamsters exposed to temperatures of -8°C and below in inverse proportion to body fat content. Serum leptin levels were positively correlated with GEI and BAT COX activity in cold-exposed hamsters, but no such relationships were observed in control animals. These findings suggest that cold-exposed hamsters increase food consumption to meet the energy requirements for increased BAT thermogenesis. The increases in serum leptin levels are likely involved in increased thermogenesis in hamsters under cold stress. Cold-exposed hamsters may become leptin resistant, which is associated with impaired regulation of food intake. This new natural model of leptin resistance may also provide insight into the dynamic long-term control of energy homeostasis for animals that do not exhibit seasonal decline in M(b).

  4. Effect of temperature on the single-particle ground-state energy of a polar quantum dot with Gaussian confinement

    Energy Technology Data Exchange (ETDEWEB)

    Jahan, Luhluh K., E-mail: luhluhjahan@gmail.com; Chatterjee, Ashok [School of Physics, University of Hyderabad, Gachibowli, Telangana India 500046 (India)

    2016-05-23

    The temperature and size dependence of the ground-state energy of a polaron in a Gaussian quantum dot have been investigated by using a variational technique. It is found that the ground-state energy increases with increasing temperature and decreases with the size of the quantum dot. Also, it is found that the ground-state energy is larger for a three-dimensional quantum dot as compared to a two-dimensional dot.

  5. Temperature, Humidity and Energy Consumption Forecasting in the Poultry Hall Using Artificial Neural Networknetwork

    Directory of Open Access Journals (Sweden)

    N Gholamrezaei

    2017-10-01

    Full Text Available Introduction Energy consumption management is one of the most important issues in poultry halls management. Considering the situation of poultry as one of the largest and most developed industries, it is needed to control growing condition based on world standards. The neural networks as one of the intelligent methods are applied in a lot of fields such as classification, pattern recognition, prediction and modeling of processes. To detect and classify several agricultural crops, a research was conducted based on texture and color feature. The highest classification accuracy for vegetables, grains and fruits with using artificial neural network were 80%, 86% and 70%. In this research, the ability to Multilayer Perceptron (MLP Neural Network in predicting energy consumption, temperature and humidity in different coordinate placement of electronic control unit sensors in the poultry house environment was examined. Materials and Methods The experiments were conducted in a poultry unit (3000 pieces that is located in Fars province, Marvdasht city, Ramjerd town, with dimensions of 32 meters long, 7 meters wide and 2.2 meters height. To determine the appropriate placement of the sensor, 60 different points in terms of length, width and height in poultry were selected. Initially, the data was divided into two datasets. 80 percent of total data as a training set and 20 percent of total data as a test set. From180 observations, 144 data were used to train network and 36 data were used to test the process. There are several criteria for evaluating predictive models that they are mainly based according to the difference between the predicted outputs and actual outputs. To evaluate the performance of the model, two statistical indexes, mean squared error (MSE and the coefficient of determination (R² were used. Results and Discussions In this study, to train artificial neural network for predicting the temperature, humidity and energy consumption, the

  6. Energy Storage and Generation for Extreme Temperature and Pressure and Directional Measurement While Drilling Applications

    Energy Technology Data Exchange (ETDEWEB)

    Signorelli, Riccardo [FastCAP Systems Corporation, Boston, MA (United States); Cooley, John [FastCAP Systems Corporation, Boston, MA (United States)

    2015-10-14

    FastCAP Systems Corporation has successfully completed all milestones defined by the award DE-EE0005503. Under this program, FastCAP developed three critical subassemblies to TRL3 demonstrating proof of concept of a geothermal MWD power source. This power source includes an energy harvester, electronics and a novel high temperature ultracapacitor (“ultracap”) rechargeable energy storage device suitable for geothermal exploration applications. FastCAP’s ruggedized ultracapacitor (ultracap) technology has been proven and commercialized in oil and gas exploration operating to rated temperatures of 150°C. Characteristics of this technology are that it is rechargeable and relatively high power. This technology was the basis for the advancements in rechargeable energy storage under this project. The ultracap performs reliably at 250°C and beyond and operates over a wide operating temperature range: -5°C to 250°C. The ultracap has significantly higher power density than lithium thionyl chloride batteries, a non-rechargeable incumbent used in oil and gas drilling today. Several hermetically sealed, prototype devices were tested in our laboratories at constant temperatures of 250°C showing no significant degradation over 2000 hours of operation. Other prototypes were tested at Sandia National Lab in the month of April, 2015 for a third party performance validation. These devices showed outstanding performance over 1000 hours of operation at three rated temperatures, 200°C, 225°C and 250°C, with negligible capacitance degradation and minimal equivalent series resistance (ESR) increase. Similarly, FastCAP’s ruggedized electronics have been proven and commercialized in oil and gas exploration operating to rated temperatures of 150°C. This technology was the basis for the advancements in downhole electronics under this project. Principal contributions here focused on design for manufacture innovations that have reduced the prototype build cycle time by a factor

  7. Scale dependent controls of stream water temperatures - interaction of advective and diffusive energy fluxes

    Science.gov (United States)

    Schuetz, Tobias; Weiler, Markus

    2017-04-01

    Diurnal stream water temperature amplitudes (WTA) have a large impact on local ecohydrological conditions, e.g. aquatic habitat quality or biogeochemical cycling. Depending on discharge, streambed geomorphology, connectivity to the groundwater, hyporheic exchange flow and other local factors such as shading and climate conditions observable WTAs vary strongly from up- to downstream and can locally even exceed seasonal temperature variations. The main process which is responsible for the local expression of WTA is the energy balance which can be either dominated by advective energy fluxes (e. g. discharge and upwelling groundwater) or by diffusive energy fluxes (e. g. radiation, latent and sensible heat fluxes, heat exchange with the streambed). In recent years research has mainly focused on improving our knowledge how groundwater-surface water interaction, hyporheic exchange and shading processes influence locally observable WTA in smaller streams, while for larger streams or rivers WTA might even be non-observable throughout the year. Within this study we analyze the scaling behavior of advective and diffusive energy fluxes from small to large streams to better understand on which scales and under which conditions WTA might be dominated either by advective or diffusive energy fluxes and how groundwater - surface water interaction influences this relationship. For this purpose, we carried out a synthetic model study. Using published hydraulic geometry relations for different types of rivers, we apply a conceptual energy balance- and mixing model, which includes GW-SW interaction, discharges from 100 l/s up to 50 m3/s on length scales from 100 m up to 50 km. Simulated boundary conditions were constant discharges at the upstream boundary and constant and uniformly distributed exchange fluxes to the groundwater. Upstream water temperatures were 15 °C (WTA of 5 °C), while groundwater temperature was assumed to be cooler than the stream with 9°C. Net diffusive energy

  8. High temperature latent heat thermal energy storage to augment solar thermal propulsion for microsatellites

    Science.gov (United States)

    Gilpin, Matthew R.

    Solar thermal propulsion (STP) offers an unique combination of thrust and efficiency, providing greater total DeltaV capability than chemical propulsion systems without the order of magnitude increase in total mission duration associated with electric propulsion. Despite an over 50 year development history, no STP spacecraft has flown to-date as both perceived and actual complexity have overshadowed the potential performance benefit in relation to conventional technologies. The trend in solar thermal research over the past two decades has been towards simplification and miniaturization to overcome this complexity barrier in an effort finally mount an in-flight test. A review of micro-propulsion technologies recently conducted by the Air Force Research Laboratory (AFRL) has identified solar thermal propulsion as a promising configuration for microsatellite missions requiring a substantial Delta V and recommended further study. A STP system provides performance which cannot be matched by conventional propulsion technologies in the context of the proposed microsatellite ''inspector" requiring rapid delivery of greater than 1500 m/s DeltaV. With this mission profile as the target, the development of an effective STP architecture goes beyond incremental improvements and enables a new class of microsatellite missions. Here, it is proposed that a bi-modal solar thermal propulsion system on a microsatellite platform can provide a greater than 50% increase in Delta V vs. chemical systems while maintaining delivery times measured in days. The realization of a microsatellite scale bi-modal STP system requires the integration of multiple new technologies, and with the exception of high performance thermal energy storage, the long history of STP development has provided "ready" solutions. For the target bi-modal STP microsatellite, sensible heat thermal energy storage is insufficient and the development of high temperature latent heat thermal energy storage is an enabling

  9. High Energy Density and High Temperature Multilayer Capacitor Films for Electric Vehicle Applications

    Science.gov (United States)

    Treufeld, Imre; Song, Michelle; Zhu, Lei; Baer, Eric; Snyder, Joe; Langhe, Deepak

    2015-03-01

    Multilayer films (MLFs) with high energy density and high temperature capability (>120 °C) have been developed at Case Western Reserve University. Such films offer a potential solution for electric car DC-link capacitors, where high ripple currents and high temperature tolerance are required. The current state-of-the-art capacitors used in electric cars for converting DC to AC use biaxially oriented polypropylene (BOPP), which can only operate at temperatures up to 85 °C requiring an external cooling system. The polycarbonate (PC)/poly(vinylidene fluoride) (PVDF) MLFs have a higher permittivity compared to that of BOPP (2.3), leading to higher energy density. They have good mechanical stability and reasonably low dielectric losses at 120 °C. Nonetheless, our preliminary dielectric measurements show that the MLFs exhibit appreciable dielectric losses (20%) at 120 °C, which would, despite all the other advantages, make them not suitable for practical applications. Our preliminary data showed that dielectric losses of the MLFs at 120 °C up to 400 MV/m and 1000 Hz originate mostly from impurity ionic conduction. This work is supported by the NSF PFI/BIC Program (IIP-1237708).

  10. Thermal energy harvesting near-infrared radiation and accessing low temperatures with plasmonic sensors.

    Science.gov (United States)

    Karker, Nicholas A; Dharmalingam, Gnanaprakash; Carpenter, Michael A

    2015-11-14

    Near-infrared (NIR) thermal energy harvesting has been demonstrated for gold nanorods (AuNRs), allowing concentration dependent, ppm-level, gas detection of H2, CO, and NO2 at 500 °C without using a white light source. Part-per-million detection capabilities of the gold nanorods are demonstrated with a factor of 11 reduction in collection times in the NIR as compared to measurements made in the visible light region. Decreased collection times are enabled by an increase in S : N ratio, which allowed a demonstration of selectivity through the use of both full spectral and a reduced spectral-based principal component analysis. Furthermore, low temperature thermal imaging spectra have been obtained at sample temperatures ranging from 275-500 °C, showing the possibility of energy harvested gas sensing at lower temperatures. These findings are promising in the area of miniaturizing plasmonic gas sensing technology and integration in areas such as gas turbines.

  11. Biological and Biomimetic Low-Temperature Routes to Materials for Energy Applications

    Energy Technology Data Exchange (ETDEWEB)

    Morse, Daniel E. [Univ. of California, Santa Barbara, CA (United States). Inst. for Collaborative Biotechnologies

    2016-08-29

    New materials are needed to significantly improve the efficiencies of energy harnessing, transduction and storage, yet the synthesis of advanced composites and multi-metallic semiconductors with nanostructures optimized for these functions remains poorly understood and even less well controlled. To help address this need, we proposed three goals: (1) to further investigate the hierarchical structure of the biologically synthesized silica comprising the skeletal spicules of sponges that we discovered, to better resolve the role and mechanism of templating by the hierarchically assembled silicatein protein filament; (2) to extend our molecular and genetic analyses and engineering of silicatein, the self-assembling, structure-directing, silica-synthesizing enzyme we discovered and characterized, to better understand and manipulate the catalysis and templating of semiconductor synthesis,; and (3) to further investigate, scale up and harness the biologically inspired, low-temperature, kinetically controlled catalytic synthesis method we developed (based on the mechanism we discovered in silicatein) to investigate the kinetic control of the structure-function relationships in magnetic materials, and develop new materials for energy applications. The bio-inspired catalytic synthesis method we have developed is low-cost, low temperature, and operates without the use of polluting chemicals. In addition to direct applications for improvement of batteries and fuel cells, the broader impact of this research includes a deeper fundamental understanding of the factors governing kinetically controlled synthesis and its control of the emergent nanostructure and performance of a wide range of nanomaterials for energy applications.

  12. Determining water use of sorghum from two-source energy balance and radiometric temperatures

    Directory of Open Access Journals (Sweden)

    J. M. Sánchez

    2011-10-01

    Full Text Available Estimates of surface actual evapotranspiration (ET can assist in predicting crop water requirements. An alternative to the traditional crop-coefficient methods are the energy balance models. The objective of this research was to show how surface temperature observations can be used, together with a two-source energy balance model, to determine crop water use throughout the different phenological stages of a crop grown. Radiometric temperatures were collected in a sorghum (Sorghum bicolor field as part of an experimental campaign carried out in Barrax, Spain, during the 2010 summer growing season. Performance of the Simplified Two-Source Energy Balance (STSEB model was evaluated by comparison of estimated ET with values measured on a weighing lysimeter. Errors of ±0.14 mm h−1 and ±1.0 mm d−1 were obtained at hourly and daily scales, respectively. Total accumulated crop water use during the campaign was underestimated by 5%. It is then shown that thermal radiometry can provide precise crop water necessities and is a promising tool for irrigation management.

  13. Low temperature thermal energy storage: a state-of-the-art survey

    Energy Technology Data Exchange (ETDEWEB)

    Baylin, F.

    1979-07-01

    The preliminary version of an analysis of activities in research, development, and demonstration of low temperature thermal energy storage (TES) technologies having applications in renewable energy systems is presented. Three major categories of thermal storage devices are considered: sensible heat; phase change materials (PCM); and reversible thermochemical reactions. Both short-term and annual thermal energy storage technologies based on prinicples of sensible heat are discussed. Storage media considered are water, earth, and rocks. Annual storage technologies include solar ponds, aquifers, and large tanks or beds of water, earth, or rocks. PCM storage devices considered employ salt hydrates and organic compounds. The sole application of reversible chemical reactions outlined is for the chemical heat pump. All program processes from basic research through commercialization efforts are investigated. Nongovernment-funded industrial programs and foreign efforts are outlined as well. Data describing low temperature TES activities are presented also as project descriptions. Projects for all these programs are grouped into seven categories: short-term sensible heat storage; annual sensible heat storage; PCM storage; heat transfer and exchange; industrial waste heat recovery and storage; reversible chemical reaction storage; and models, economic analyses, and support studies. Summary information about yearly funding and brief descriptions of project goals and accomplishments are included.

  14. Development of Front Surface, Spectral Control Filters with Greater Temperature Stability for Thermophotovoltaic Energy Conversion

    Energy Technology Data Exchange (ETDEWEB)

    TD Rahmlow, Jr.; DM DePoy; PM Fourspring; H Ehsani; JE Lazo-Wasem; EJ Gratiix

    2006-10-02

    Spectral control is an important consideration in achieving high conversion efficiency with thermophotovoltaic (TPV) energy conversion systems. TPV modules using front surface filters as the primary spectral control device have demonstrated conversion efficiencies in excess of 20% with power densities in excess of 0.4 W/cm{sup 2}. The front surface filter we are developing is a short pass, long wavelength reflection filter consisting of an interference filter deposited on a plasma filter. The materials used in the interference filter must exhibit high broad band transmission and good film quality and sufficient temperature stability at the operating temperature of the TPV cells and over any potential temperature excursions that may occur. Three high refractive index materials that offer good potential for use in TPV spectral control filters are antimony selenide (Sb{sub 2}Se{sub 3}), antimony sulfide (Sb{sub 2}S{sub 3}), and gallium telluride (GaTe). The highest spectral efficiency has been demonstrated using Sb{sub 2}Se{sub 3}; however this material develops significant near infrared (NIR, 0.72-2.5 {micro}m) absorption at temperatures in excess of 90 C. The other two materials are being developed as high temperature alternatives to Sb{sub 2}Se{sub 3}. TPV filters using GaTe and Sb{sub 2}S{sub 3} have been designed and fabricated, and initial results indicate that GaTe based filters are capable of operation at temperatures of 150 C or greater. Measured performance of TPV filters containing Sb{sub 2}Se{sub 3}, GaTe and Sb{sub 2}S{sub 3} are presented, along with the impact that these have on TPV module performance.

  15. Borehole temperatures reveal a changed energy budget at Mill Island, East Antarctica, over recent decades

    Directory of Open Access Journals (Sweden)

    J. L. Roberts

    2013-02-01

    Full Text Available A borehole temperature record from the Mill Island (East Antarctica icecap reveals a large surface warming signal manifested as a 0.75 K temperature difference over the approximate 100 m depth in the zone of zero annual amplitude below the seasonally varying zone. The temperature profile shows a break in gradient around 49 m depth, which we model with inverse numerical simulations, indicating that surface warming started around the austral summer of 1980/81 AD ±5 yr. This warming of approximately 0.37 K per decade is consistent with trends seen in both instrumental and other reconstructions for Antarctica and, therefore, suggests that regional- rather than local-scale processes are largely responsible. Alteration of the surface energy budget arising from changes in radiation balances due to local cloud, the amount of liquid deposition and local air temperatures associated with altered air/sea exchanges also potentially plays a role at this location due to the proximity of the Shackleton Ice Shelf and sea-ice zone.

  16. Improvement of Surface skin temperature simulation over the Tibetan Plateau from an energy balance perspective

    Science.gov (United States)

    Zhuo, Haifeng

    2015-04-01

    There has a big cold bias of temperature about reanalysis and simulations over Tibetan Plateau comparing with observations. In order to solve this problem, for the land -- atmosphere interaction in arid and semi-arid region is mainly dominated by heat transfer process, a latest revision of surface sensible heat parameterization introduced by Zeng et al is then used for bare soil in WRFV3 (CLM4) model. Results show that the annual surface skin temperature has approximately up to 2.0 degree improvement on average over Tibetan Plateau. Firstly, the revised scheme changes the energy balance over and around Tibetan Plateau. It significantly reduces the overestimate of surface sensible heat and improves the surface skin temperature simulation, which tends more close to the observation. Secondly, the revised scheme weakens the sensible heat air pump effect of Tibetan Plateau. The diabatic heating reduce and the updraft airflow weaken especially over the southern slope of plateau, meanwhile the clouds thin, the incident solar radiation increases, eventually led to the increase of surface skin temperature in North India in dry season.

  17. Temperature dependence of the kinetic energy in the Zr40Be60 amorphous alloy

    Science.gov (United States)

    Syrykh, G. F.; Stolyarov, A. A.; Krzystyniak, M.; Romanelli, G.; Sadykov, R. A.

    2017-05-01

    The average kinetic energy of the atomic nucleus for each element of the amorphous alloy Zr40Be60 in the temperature range 10-300 K has been measured for the first time using VESUVIO spectrometer (ISIS). The experimental values of have been compared to the partial ZrBe spectra refined by a recursion method based on the data obtained with thermal neutron scattering. The satisfactory agreement has been reached with the calculations using partial spectra based on thermal neutron spectra obtained with recursion method. In addition, the experimental data have been compared to the Debye model. The measurements at different temperatures (10, 200, and 300 K) will provide an opportunity to evaluate the significance of anharmonicity in the dynamics of metallic glasses.

  18. Thermal measurement of root surface temperatures during application of intracanal laser energy in vitro

    Science.gov (United States)

    Goodis, Harold E.; White, Joel M.; Neev, Joseph

    1993-07-01

    The use of laser energy to clean, shape, and sterilize a root canal system space involves the generation of heat due to the thermal effect of the laser on the organic tissue contents and dentin walls of that space. If heat generation is above physiologic levels, irreparable damage may occur to the periodontal ligament and surrounding bone. This study measured temperature rise on the outer root surfaces of extracted teeth during intracanal laser exposure. Thirty single rooted, recently extracted teeth free of caries and restorations were accessed pulps extirpated and divided into three groups. Each root canal system was treated with a 1.06 micrometers pulsed Nd:YAG laser with quartz contact probes. Temperatures were recorded for all surfaces (mesial distal, buccal, lingual, apical) with infrared thermography utilizing a detector response time of 1 (mu) sec, sensitivity range (infrared) of 8 to 12 micrometers and a scan rate of 30 frames/sec.

  19. Temperature and energy consumption for clothing dryer; Temperatura e consumo de energia em secadora de vestuario

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Jefferson Almeida; Magalhaes Filho, Paulo [UNESP, Guaratingueta, SP (Brazil). Faculdade de Engenharia. Dept. de Energia]. E-mail: pfilho@feg.unesp.br

    2000-07-01

    The cloth dehumidification is done by hot air circulation through it in dryers. The air circulation is done by a fan, run by an electrical motor, and the air temperature raise, which goes through the cloths aiming their moisture dragging, is gotten by the heat dissipation from electrical resistance. This work shows the results of an experimental modeling, examining the behavior of several kinds of cloth in a vertical suspense-type dryer, such as: polyester, cotton-spandex, flannel, blue-jeans and viscose rayon. It was analyzed the behavior of the moisture content in these cloths related to controlled-temperature-air flows, determining the needed heat to reach the required drying standards. The drying device fans were tested for the determination of their flow rate and energy consumption, establishing a flow rate versus consumption relationship. Comparative results among the various kinds of cloths are presented. (author)

  20. Application of high temperature phase change materials for improved efficiency in waste-to-energy plants.

    Science.gov (United States)

    Dal Magro, Fabio; Xu, Haoxin; Nardin, Gioacchino; Romagnoli, Alessandro

    2018-03-01

    This study reports the thermal analysis of a novel thermal energy storage based on high temperature phase change material (PCM) used to improve efficiency in waste-to-energy plants. Current waste-to-energy plants efficiency is limited by the steam generation cycle which is carried out with boilers composed by water-walls (i.e. radiant evaporators), evaporators, economizers and superheaters. Although being well established, this technology is subjected to limitations related with high temperature corrosion and fluctuation in steam production due to the non-homogenous composition of solid waste; this leads to increased maintenance costs and limited plants availability and electrical efficiency. The proposed solution in this paper consists of replacing the typical refractory brick installed in the combustion chamber with a PCM-based refractory brick capable of storing a variable heat flux and to release it on demand as a steady heat flux. By means of this technology it is possible to mitigate steam production fluctuation, to increase temperature of superheated steam over current corrosion limits (450°C) without using coated superheaters and to increase the electrical efficiency beyond 34%. In the current paper a detailed thermo-mechanical analysis has been carried out in order to compare the performance of the PCM-based refractory brick against the traditional alumina refractory bricks. The PCM considered in this paper is aluminium (and its alloys) whereas its container consists of high density ceramics (such as Al 2 O 3 , AlN and Si 3 N 4 ); the different coefficient of linear thermal expansion for the different materials requires a detailed thermo-mechanical analysis to be carried out to ascertain the feasibility of the proposed technology. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Mechanical properties of composites as functions of the syringe storage temperature and energy dose.

    Science.gov (United States)

    Chaves, Fernanda Oliveira; Farias, Natália Coelho de; Medeiros, Luciano Marcelo de Mello; Alonso, Roberta Caroline Bruschi; Di Hipólito, Vinicius; D'Alpino, Paulo Henrique Perlatti

    2015-01-01

    To investigate the mechanical properties of different classifications of composites indicated for posterior application as functions of the storage condition and of the energy dose. Specimens (8 x 2 x 2 mm) were obtained according to the factors: I) Composites (3M ESPE): Filtek P60, Filtek Z350XT, and Filtek Silorane; II) Syringe storage conditions: room temperature, aged, oven, refrigerator, and freezer; and III) Energy dose: 24 J/cm(2) and 48 J/cm(2). After photoactivation, the specimens were stored at 37 ºC for 24 h. After storage, a three-point bending test was carried out in a universal testing machine at 0.5 mm/min. Flexural strength (S) and flexural modulus (E) were calculated. Data were analyzed by three-way ANOVA and Tukey's test (α = 0.05). Different storage conditions significantly affected the silorane composite for S; conversely, no effects were noted in terms of E. The accelerated aging protocol significantly increased the S of Filtek P60 and Filtek Silorane, whereas storage in the oven significantly decreased the S for all of the composites tested. Filtek P60 was the only composite not affected by the lower storage temperatures tested for S, whereas for the silorane this parameter was impacted at the same conditions. The factor "dose" was not statistically significant. The syringe storage at different temperature conditions proved to influence mostly the flexural strength, a clinically important characteristic considering the posterior indication of the materials tested. The silorane composite should not be stored at lower temperatures.

  2. Mechanical properties of composites as functions of the syringe storage temperature and energy dose

    Directory of Open Access Journals (Sweden)

    Fernanda Oliveira CHAVES

    2015-04-01

    Full Text Available Objective: To investigate the mechanical properties of different classifications of composites indicated for posterior application as functions of the storage condition and of the energy dose. Material and Methods: Specimens (8x2x2 mm were obtained according to the factors: I Composites (3M ESPE: Filtek P60, Filtek Z350XT, and Filtek Silorane; II Syringe storage conditions: room temperature, aged, oven, refrigerator, and freezer; and III Energy dose: 24 J/cm2 and 48 J/cm2. After photoactivation, the specimens were stored at 37ºC for 24 h. After storage, a three-point bending test was carried out in a universal testing machine at 0.5 mm/min. Flexural strength (S and flexural modulus (E were calculated. Data were analyzed by three-way ANOVA and Tukey's test (α=0.05. Results: Different storage conditions significantly affected the silorane composite for S; conversely, no effects were noted in terms of E. The accelerated aging protocol significantly increased the S of Filtek P60 and Filtek Silorane, whereas storage in the oven significantly decreased the S for all of the composites tested. Filtek P60 was the only composite not affected by the lower storage temperatures tested for S, whereas for the silorane this parameter was impacted at the same conditions. The factor "dose" was not statistically significant. Conclusions: The syringe storage at different temperature conditions proved to influence mostly the flexural strength, a clinically important characteristic considering the posterior indication of the materials tested. The silorane composite should not be stored at lower temperatures.

  3. Direct-contact high-temperature thermal energy storage heat exchanger

    Science.gov (United States)

    Alario, J. P.; Brown, R.

    1983-09-01

    A 10 kWh scale model high temperature direct contact latent heat exchange thermal energy storage system was fabricated. A research program was structured in three separate phases: (1) the inspection and evaluation of the original hardware, which suffered extensive corrosion and damage in a previous experimental program; (2) redesign and fabrication of a modified system, and (3) detailed test evaluation. In phase 1, the design was modified to eliminate previous deficiencies. Phase 2 entailed component procurement and fabrication, system assembly, and instrumentation. The results for the design and fabrication phases of the program are presented.

  4. 3WCC Temperature Integration in a Gasoline-HEV Optimal Energy Management Strategy

    Directory of Open Access Journals (Sweden)

    Pierre Michel

    2014-02-01

    Full Text Available For a gasoline-hybrid electric vehicle (HEV, the energy management strategy (EMS is the computation of the distribution between electric and gasoline propulsion. Until recently, the EMS objective was to minimize fuel consumption. However, decreasing fuel consumption does not directly minimize the pollutant emissions, and the 3-way catalytic converter (3WCC must be taken into account. This paper proposes to consider the pollutant emissions in the EMS, by minimizing, with the Pontryagin minimum principle, a tradeoff between pollution and fuel consumption. The integration of the 3WCC temperature in the EMS is discussed and finally a simplification is proposed.

  5. Lowering district heating temperatures – Impact to system performance in current and future Danish energy scenarios

    DEFF Research Database (Denmark)

    Ommen, Torben; Markussen, Wiebke Brix; Elmegaard, Brian

    2016-01-01

    , the changed distribution of generation technologies may suggest a reconsideration of optimum for DH network temperatures, in order to achieve low cost and minimize carbon emissions. A mixed integer linear optimisation model was used to investigate the changed operation based on changed network characteristics......CHP (Combined heat and power) production in connection with DH (district heating) systems has previously demonstrated a significant reduction in primary energy consumption. With extended installation of intermittent sustainable sources, such as eg. wind turbines rather than thermal units...

  6. Summer declines in activity and body temperature offer polar bears limited energy savings

    Science.gov (United States)

    Whiteman, J.P.; Harlow, H.J.; Durner, George M.; Anderson-Sprecher, R.; Albeke, Shannon E.; Regehr, Eric V.; Amstrup, Steven C.; Ben-David, M.

    2015-01-01

    Polar bears (Ursus maritimus) summer on the sea ice or, where it melts, on shore. Although the physiology of “ice” bears in summer is unknown, “shore” bears purportedly minimize energy losses by entering a hibernation-like state when deprived of food. Such a strategy could partially compensate for the loss of on-ice foraging opportunities caused by climate change. However, here we report gradual, moderate declines in activity and body temperature of both shore and ice bears in summer, resembling energy expenditures typical of fasting, nonhibernating mammals. Also, we found that to avoid unsustainable heat loss while swimming, bears employed unusual heterothermy of the body core. Thus, although well adapted to seasonal ice melt, polar bears appear susceptible to deleterious declines in body condition during the lengthening period of summer food deprivation.

  7. GIS to support cost-effective decisions on renewable sources applications for low temperature geothermal energy

    CERN Document Server

    Gemelli, Alberto; Diamantini, Claudia; Longhi, Sauro

    2013-01-01

    Through the results of a developed case study of information system for low temperature geothermal energy, GIS to Support Cost-effective Decisions on Renewable Sources addresses the issue of the use of Geographic Information Systems (GIS) in evaluating cost-effectiveness of renewable resource exploitation regional scale. Focusing on the design of a Decision Support System, a process is presented aimed to transform geographic data into knowledge useful for analysis and decision-making on the economic exploitation of geothermal energy. This detailed description includes a literature review and technical issues related to data collection, data mining, decision analysis for the informative system developed for the case study. A multi-disciplinary approach to GIS design is presented which is also an innovative example of fusion of georeferenced data acquired from multiple sources including remote sensing, networks of sensors and socio-economic censuses. GIS to Support Cost-effective Decisions on Renewable Sources ...

  8. Economic study of low temperature geothermal energy in Lassen and Modoc Counties, California

    Energy Technology Data Exchange (ETDEWEB)

    1977-04-01

    The feasibility of using low cost, low temperature geothermal energy in job-producing industries to increase employment and encourage economic development was investigated. The study, encompassing all of Lassen and Modoc Counties, was to be site-specific, referencing candidate geothermal applications to known hot wells and springs as previously determined, or to new wells with specific characteristics as defined in the Scope of Work. The emphasis was to be placed on economically practical and readily achievable applications from known resources. Although both positive and negative findings were found in specific areas of investigation, it is felt that the overall long term prognosis for geothermal energy stimulus to industry in the area is excellent. The applications studied were; greenhouse heating, kiln drying, onion dehydration, feedlots, and aquaculture.

  9. Animal physiology. Summer declines in activity and body temperature offer polar bears limited energy savings.

    Science.gov (United States)

    Whiteman, J P; Harlow, H J; Durner, G M; Anderson-Sprecher, R; Albeke, S E; Regehr, E V; Amstrup, S C; Ben-David, M

    2015-07-17

    Polar bears (Ursus maritimus) summer on the sea ice or, where it melts, on shore. Although the physiology of "ice" bears in summer is unknown, "shore" bears purportedly minimize energy losses by entering a hibernation-like state when deprived of food. Such a strategy could partially compensate for the loss of on-ice foraging opportunities caused by climate change. However, here we report gradual, moderate declines in activity and body temperature of both shore and ice bears in summer, resembling energy expenditures typical of fasting, nonhibernating mammals. Also, we found that to avoid unsustainable heat loss while swimming, bears employed unusual heterothermy of the body core. Thus, although well adapted to seasonal ice melt, polar bears appear susceptible to deleterious declines in body condition during the lengthening period of summer food deprivation. Copyright © 2015, American Association for the Advancement of Science.

  10. Decay Time Measurement for Different Energy Depositions of Plastic Scintillator Fabricated by High Temperature Polymerization Reaction

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Cheol Ho; Son, Jaebum; Lee, Sangmin; Kim, Tae Hoon; Kim, Yong-Kyun [Hanyang University, Seoul (Korea, Republic of)

    2016-10-15

    Plastic scintillators are based on organic fluorite. They have many advantages such as fast rise and decay time, high optical transmission, ease of manufacturing, low cost, and large available size. For these reasons they are widely used for particle identification. Also, protection of people against a variety of threats (such as nuclear, radiological, and explosive) represents a true challenge along with the continuing development of science and technology. The plastic scintillator is widely used in various devise, which serves for nuclear, photonics, quantum, and high-energy physics. The plastic scintillator is probably the most widely used organic detector, and polystyrene is one of the most widely used materials in the making of the plastic scintillator detector. Thus, a styrene monomer as a solvent was used to fabricate the plastic scintillator by using high temperature polymerization reaction, and then the emission wavelength and the decay times for different energy depositions were measured by using the fabricated plastic scintillator. A plastic scintillator was fabricated to measure decay time for different energy depositions using the high temperature polymerization. Emission wavelength was measured of 426.05 nm to confirm a scintillator property using the spectrophotometer. Four gamma-ray sources (Cs-137, Co-60, Na-22, and Ba-133) were used to evaluate effect for decay time of different energy depositions. The average decay time of the fabricated plastic scintillator was measured to approximately 4.72 ns slightly higher more than commercial plastic scintillator. In future, light output and linearity will be measured to evaluate other property compared with the commercial scintillator.

  11. Male weasels decrease activity and energy expenditure in response to high ambient temperatures.

    Directory of Open Access Journals (Sweden)

    Karol Zub

    Full Text Available The heat dissipation limit (HDL hypothesis suggests that the capacity of endotherms to dissipate body heat may impose constraints on their energy expenditure. Specifically, this hypothesis predicts that endotherms should avoid the detrimental consequences of hyperthermia by lowering their energy expenditure and reducing their activity in response to high ambient temperatures (T(a. We used an extensive data set on the daily energy expenditure (DEE, n = 27 and the daily activity time (AT, n = 48 of male weasels (Mustela nivalis during the spring and summer breeding season to test these predictions. We found that T(a was related in a "hump-shaped" (i.e. convex manner to AT, DEE, resting metabolic rate (RMR and metabolic scope (the ratio of DEE to RMR. These results support the HDL hypothesis because in response to warm Tas male weasels reduced their AT, DEE, and RMR. Although the activity and energy expenditure of large endotherms are most likely to be constrained in response to warm Tas because they are less able to dissipate heat, our results suggest that small endotherms may also experience constraints consistent with the HDL hypothesis.

  12. Generation of high-temperature steam from unused thermal energy by a novel adsorption heat pump

    Science.gov (United States)

    Nakaso, Koichi; Eshima, Shotaro; Fukai, Jun

    2017-01-01

    For the effective utilization of unused thermal energy, the novel adsorption heat pump system for generating high-temperature steam is proposed. This system adopts a direct heat exchange method to the adsorption heat pump to increase heat transfer rate between adsorbent and heat transfer fluid. The heat pump system consists of two processes: steam generation process and regeneration process. In the steam generation process, water is directly introduced to the adsorbent. In the regeneration process, dry gas is introduced to the adsorbent. In this study, the performance of the system is numerically evaluated. The efficiency of the heat pump system is calculated by the ratio of enthalpy of product steam to input energy. To calculate the enthalpy of steam, mass of steam generated is estimated based on the progress of the regeneration process. Input energy of the heat pump system consists of the blower power to introduce dry gas and the thermal energy to heat dry gas. The effect of the operating condition on the performance of the steam generation process is studied. It is found there is the appropriate regeneration time to maximize the efficiency of the heat pump system.

  13. Combinatorial Phase Separation of Polymer Blends: Surface Energy, Temperature and Film Confinement Effects

    Science.gov (United States)

    Karim, Alamgir

    2003-03-01

    Control of pattern scale of ultrathin film polymeric surfaces has many potential applications such as anti-reflection coatings, optical sieves, controlled tissue growth or adhesion control. We combinatorially investigate the influence of surface energy E, film thickness H, and temperature T, on the late stage surface morphology of phase separating polymer blend films of polystyrene-polyvinylmethylether. A simple gradient UV approach was used to create stable substrates with a range of surface energies. Confinement between air and substrate interfaces and preferential wetting of components at the walls determines the aspect ratio of the phase separated structures. A non-monotonic change in the lateral scale of phase separation, L and surface roughness with surface energy is observed along with the systematic increase with thickness. We describe the L dependence on E by the empirical relationship, L ˜ A exp[-(E-E*)/S^2] for fixed H, where the pre-factor A is film thickness dependent and S characterizes the peak width about an inversion surface energy E*. Application to studies of a biocompatible blend of poly(e-caprolactone) and poly(D-L Lactic Acid) to assay cellular response to topographical scales as well as millifluidic approaches to the problem will be discussed.

  14. Study of Creep of Alumina-Forming Austenitic Stainless Steel for High-Temperature Energy Applications

    Science.gov (United States)

    Afonina, Natalie Petrovna

    To withstand the high temperature (>700°C) and pressure demands of steam turbines and boilers used for energy applications, metal alloys must be economically viable and have the necessary material properties, such as high-temperature creep strength, oxidation and corrosion resistance, to withstand such conditions. One promising class of alloys potentially capable of withstanding the rigors of aggressive environments, are alumina-forming austenitic stainless steels (AFAs) alloyed with aluminum to improve corrosion and oxidation resistance. The effect of aging on the microstructure, high temperature constant-stress creep behavior and mechanical properties of the AFA-type alloy Fe-20Cr-30Ni-2Nb-5Al (at.%) were investigated in this study. The alloy's microstructural evolution with increased aging time was observed prior to creep testing. As aging time increased, the alloy exhibited increasing quantities of fine Fe2Nb Laves phase dispersions, with a precipitate-free zone appearing in samples with higher aging times. The presence of the L1 2 phase gamma'-Ni3Al precipitate was detected in the alloy's matrix at 760°C. A constant-stress creep rig was designed, built and its operation validated. Constant-stress creep tests were performed at 760°C and 35MPa, and the effects of different aging conditions on creep rate were investigated. Specimens aged for 240 h exhibited the highest creep rate by a factor of 5, with the homogenized sample having the second highest rate. Samples aged for 2.4 h and 24 h exhibited similar low secondary creep rates. Creep tests conducted at 700oC exhibited a significantly lower creep rate compared to those at 760oC. Microstructural analysis was performed on crept samples to explore high temperature straining properties. The quantity and size of Fe2Nb Laves phase and NiAl particles increased in the matrix and on grain boundaries with longer aging time. High temperature tensile tests were performed and compared to room temperature results. The

  15. Using Graphs of Gibbs Energy versus Temperature in General Chemistry Discussions of Phase Changes and Colligative Properties

    Science.gov (United States)

    Hanson, Robert M.; Riley, Patrick; Schwinefus, Jeff; Fischer, Paul J.

    2008-01-01

    The use of qualitative graphs of Gibbs energy versus temperature is described in the context of chemical demonstrations involving phase changes and colligative properties at the general chemistry level. (Contains 5 figures and 1 note.)

  16. Temperature dependence of first lattice corrections to the free-energy of kink compacton-bearing systems

    Energy Technology Data Exchange (ETDEWEB)

    Yemele, David [Departement de Physique, Faculte des Sciences, Universite de Dschang, BP 067 Dschang (Cameroon); Kofane, Timoleon C [Laboratoire de Mecanique, Faculte des Sciences, Universite de Yaounde I, BP 812 Yaounde (Cameroon)

    2005-03-16

    The free-energy of discrete nonlinear Klein-Gordon (NKG) systems with anharmonic interparticle interactions is derived by means of the transfer integral operator method, with the first lattice corrections and kink-kink interactions taken into account. Two particular substrate potentials are considered: the {phi}-four and the sine-Gordon (sG). We show that, in the general case where the system exhibits the kink soliton like excitations, the correction factors, due to the lattice discreteness, appearing in the free-energy and in the lattice corrected static kink soliton energy, depend on the temperature through a coupling of the interparticle anharmonicity strength to the temperature. Similarly, in the purely anharmonic NKG systems, characterized by the absence of the linear dispersion, where thermodynamic properties are sensitive to kink compactons, we find also that the correction factors are temperature dependent. In both cases, they decrease with increasing temperatures, although the correction factors verify different temperature laws.

  17. Basking hamsters reduce resting metabolism, body temperature and energy costs during rewarming from torpor.

    Science.gov (United States)

    Geiser, Fritz; Gasch, Kristina; Bieber, Claudia; Stalder, Gabrielle L; Gerritsmann, Hanno; Ruf, Thomas

    2016-07-15

    Basking can substantially reduce thermoregulatory energy expenditure of mammals. We tested the hypothesis that the largely white winter fur of hamsters (Phodopus sungorus), originating from Asian steppes, may be related to camouflage to permit sun basking on or near snow. Winter-acclimated hamsters in our study were largely white and had a high proclivity to bask when resting and torpid. Resting hamsters reduced metabolic rate (MR) significantly (>30%) when basking at ambient temperatures (Ta) of ∼15 and 0°C. Interestingly, body temperature (Tb) also was significantly reduced from 34.7±0.6°C (Ta 15°C, not basking) to 30.4±2.0°C (Ta 0°C, basking), which resulted in an extremely low (50%) during radiant heat-assisted rewarming; however, radiant heat per se without an endogenous contribution by animals did not strongly affect metabolism and Tb during torpor. Our data show that basking substantially modifies thermal energetics in hamsters, with a drop of resting Tb and MR not previously observed and a reduction of rewarming costs. The energy savings afforded by basking in hamsters suggest that this behaviour is of energetic significance not only for mammals living in deserts, where basking is common, but also for P. sungorus and probably other cold-climate mammals. © 2016. Published by The Company of Biologists Ltd.

  18. Anderson acceleration and application to the three-temperature energy equations

    Science.gov (United States)

    An, Hengbin; Jia, Xiaowei; Walker, Homer F.

    2017-10-01

    The Anderson acceleration method is an algorithm for accelerating the convergence of fixed-point iterations, including the Picard method. Anderson acceleration was first proposed in 1965 and, for some years, has been used successfully to accelerate the convergence of self-consistent field iterations in electronic-structure computations. Recently, the method has attracted growing attention in other application areas and among numerical analysts. Compared with a Newton-like method, an advantage of Anderson acceleration is that there is no need to form the Jacobian matrix. Thus the method is easy to implement. In this paper, an Anderson-accelerated Picard method is employed to solve the three-temperature energy equations, which are a type of strong nonlinear radiation-diffusion equations. Two strategies are used to improve the robustness of the Anderson acceleration method. One strategy is to adjust the iterates when necessary to satisfy the physical constraint. Another strategy is to monitor and, if necessary, reduce the matrix condition number of the least-squares problem in the Anderson-acceleration implementation so that numerical stability can be guaranteed. Numerical results show that the Anderson-accelerated Picard method can solve the three-temperature energy equations efficiently. Compared with the Picard method without acceleration, Anderson acceleration can reduce the number of iterations by at least half. A comparison between a Jacobian-free Newton-Krylov method, the Picard method, and the Anderson-accelerated Picard method is conducted in this paper.

  19. Microencapsulation of metal-based phase change material for high-temperature thermal energy storage.

    Science.gov (United States)

    Nomura, Takahiro; Zhu, Chunyu; Sheng, Nan; Saito, Genki; Akiyama, Tomohiro

    2015-03-13

    Latent heat storage using alloys as phase change materials (PCMs) is an attractive option for high-temperature thermal energy storage. Encapsulation of these PCMs is essential for their successful use. However, so far, technology for producing microencapsulated PCMs (MEPCMs) that can be used above 500°C has not been established. Therefore, in this study, we developed Al-Si alloy microsphere MEPCMs covered by α-Al2O3 shells. The MEPCM was prepared in two steps: (1) the formation of an AlOOH shell on the PCM particles using a boehmite treatment, and (2) heat-oxidation treatment in an O2 atmosphere to form a stable α-Al2O3 shell. The MEPCM presented a melting point of 573°C and latent heat of 247 J g(-1). The cycling performance showed good durability. These results indicated the possibility of using MEPCM at high temperatures. The MEPCM developed in this study has great promise in future energy and chemical processes, such as exergy recuperation and process intensification.

  20. Optical solar energy adaptations and radiative temperature control of green leaves and tree barks

    Energy Technology Data Exchange (ETDEWEB)

    Henrion, Wolfgang; Tributsch, Helmut [Department of Si-Photovoltaik and Solare Energetik, Hahn-Meitner-Institut Berlin, 14109 Berlin (Germany)

    2009-01-15

    Trees have adapted to keep leaves and barks cool in sunshine and can serve as interesting bionic model systems for radiative cooling. Silicon solar cells, on the other hand, loose up to one third of their energy efficiency due to heating in intensive sunshine. It is shown that green leaves minimize absorption of useful radiation and allow efficient infrared thermal emission. Since elevated temperatures are detrimental for tensile water flow in the Xylem tissue below barks, the optical properties of barks should also have evolved so as to avoid excessive heating. This was tested by performing optical studies with tree bark samples from representative trees. It was found that tree barks have optimized their reflection of incoming sunlight between 0.7 and 2 {mu}m. This is approximately the optical window in which solar light is transmitted and reflected by green vegetation. Simultaneously, the tree bark is highly absorbing and thus radiation emitting between 6 and 10 {mu}m. These two properties, mainly provided by tannins, create optimal conditions for radiative temperature control. In addition, tannins seem to have adopted a function as mediators for excitation energy towards photo-antioxidative activity for control of radiation damage. The results obtained are used to discuss challenges for future solar cell optimization. (author)

  1. Impacts of convection on high-temperature aquifer thermal energy storage

    Science.gov (United States)

    Beyer, Christof; Hintze, Meike; Bauer, Sebastian

    2016-04-01

    Seasonal subsurface heat storage is increasingly used in order to overcome the temporal disparities between heat production from renewable sources like solar thermal installations or from industrial surplus heat and the heat demand for building climatisation or hot water supply. In this context, high-temperature aquifer thermal energy storage (ATES) is a technology to efficiently store and retrieve large amounts of heat using groundwater wells in an aquifer to inject or withdraw hot or cold water. Depending on the local hydrogeology and temperature amplitudes during high-temperature ATES, density differences between the injected hot water and the ambient groundwater may induce significant convective flow components in the groundwater flow field. As a consequence, stored heat may accumulate at the top of the storage aquifer which reduces the heat recovery efficiency of the ATES system. Also, an accumulation of heat at the aquifer top will induce increased emissions of heat to overlying formations with potential impacts on groundwater quality outside of the storage. This work investigates the impacts of convective heat transport on the storage efficiency of a hypothetical high-temperature ATES system for seasonal heat storage as well as heat emissions to neighboring formations by numerical scenario simulations. The coupled groundwater flow and heat transport code OpenGeoSys is used to simulate a medium scale ATES system operating in a sandy aquifer of 20 m thickness with an average groundwater temperature of 10°C and confining aquicludes at top and bottom. Seasonal heat storage by a well doublet (i.e. one fully screened "hot" and "cold" well, respectively) is simulated over a period of 10 years with biannual injection / withdrawal cycles at pumping rates of 15 m³/h and for different scenarios of the temperature of the injected water (20, 35, 60 and 90 °C). Simulation results show, that for the simulated system significant convective heat transport sets in when

  2. Energy

    CERN Document Server

    Robertson, William C

    2002-01-01

    Confounded by kinetic energy? Suspect that teaching about simple machines isn t really so simple? Exasperated by electricity? If you fear the study of energy is beyond you, this entertaining book will do more than introduce you to the topic. It will help you actually understand it. At the book s heart are easy-to-grasp explanations of energy basics work, kinetic energy, potential energy, and the transformation of energy and energy as it relates to simple machines, heat energy, temperature, and heat transfer. Irreverent author Bill Robertson suggests activities that bring the basic concepts of energy to life with common household objects. Each chapter ends with a summary and an applications section that uses practical examples such as roller coasters and home heating systems to explain energy transformations and convection cells. The final chapter brings together key concepts in an easy-to-grasp explanation of how electricity is generated. Energy is the second book in the Stop Faking It! series published by NS...

  3. The Temperature Dependence on Intermolecular Potential Energy in the Design of a Supercritical Stirling Cycle Heat Engine

    OpenAIRE

    Marko, Matthew David

    2017-01-01

    The Stirling thermodynamic heat engine cycle is modified, where instead of an ideal gas, a real, supercritical, monatomic working fluid subjected to intermolecular attractive forces is used. The potential energy of real gases is redefined to show it decreasing with temperature as a result of the attractive Keesom forces, which are temperature dependent. This new definition of potential energy is used to thermodynamically design a Stirling cycle heat engine with supercritical xenon gas, and an...

  4. Effect of finite energy of intravalley acoustic phonons on the temperature of non-equilibrium electrons in a quantum surface

    Energy Technology Data Exchange (ETDEWEB)

    Nag, S. [Department of Physics, Jadavpur University, Kolkata 700032 (India); Bhattacharya, D.P., E-mail: d_p_bhattacharya@rediffmail.co [Department of Physics, Jadavpur University, Kolkata 700032 (India)

    2009-11-15

    The effect of finite energy of intravalley acoustic phonons on the electric field dependence of the temperature of the non-equilibrium carriers in a quantum surface has been studied here. The calculations have been made, for a rather pure material, at low lattice temperature. Numerical results are obtained for GaAs and Si. The results are interesting being significantly different from what one obtains by neglecting the phonon energy.

  5. Theoretical analytical model of vacancy formation energy with simultaneous dependence on surface orientation, temperature, and material size

    Science.gov (United States)

    Zhang, Xuyao; Li, Weiguo; Deng, Yong; Shao, Jiaxing; Kou, Haibo; Ma, Jianzuo; Zhang, Xianhe; Li, Ying

    2018-02-01

    From the perspectives of bond energy theory, the bond–order–length–strength correlation mechanism, and the core–surface configuration for nanomaterials, a physics-based model, free of any adjustable parameters and simultaneously considering the coupling effects of surface orientation, temperature, and size on the vacancy formation energy of metal materials is developed. To confirm our present model, the temperature-dependent vacancy formation energies of six face-centered cubic metals and the size-dependent vacancy formation energies of gold particles are predicted, which are in reasonable agreement with the simulation results. In particular, the model can provide a convenient method to predict the temperature-dependent vacancy formation energy of nanomaterials with different surface orientations, and also can provide a new method to study the structural relaxation. The study shows that the size effect on the vacancy formation energy depends on the stronger bond energy in the surface layers compared with those in the core interior, and the temperature-dependent vacancy formation energy arises from cohesive energy weakening, with the opposite trend to that induced by size reduction.

  6. Maximum Potential of the Car Cabin Temperature in the Outdoor Parking Conditions as a Source of Energy in Thermoelectric Generator

    Science.gov (United States)

    Sunawar, A.; Garniwa, I.

    2017-03-01

    Cars using the principle of converting heat energy into mechanical energy, but a lot of wasted heat energy not entirely transformed into mechanical energy, studies have been conducted that converts the heat energy into electrical energy using the principle thermoelectrically. However, there are many other energies that can be harnessed from the car, such as when the car is parked in the sun or driving in the heat of the sun, the temperature in the cabin can reach 80 degrees Celsius. The heat can be harmful to humans and the children immediately into the vehicle, as well as for the goods stored in the cabin if it contains toxins can evaporate because of the heat and dangerous. The danger can be prevented by reducing the heat in the cabin and transform into other forms of energy such as electricity. By providing a temperature difference of 40 degrees on the cold side of the module can be acquired electricity thermoelectrically up to 0.17W for one of its module, if it is made a module block the energy produced is enough to lower the temperature and charge batteries for further cooling. This study will use experiment method to get the maximum drop in temperature in the car cabin

  7. High-temperature diode laser pumps for directed energy fiber lasers (Conference Presentation)

    Science.gov (United States)

    Kanskar, Manoj; Bao, Ling; Chen, Zhigang; DeVito, Mark; Dong, Weimin; Grimshaw, Mike P.; Guan, Xinguo; Hemenway, David M.; Martinsen, Robert; Zhang, Jim; Zhang, Shiguo

    2017-05-01

    Kilowatt-class fiber lasers and amplifiers are becoming increasingly important building blocks for power-scaling laser systems in various different architectures for directed energy applications. Currently, state-of-the-art Yb-doped fiber lasers operating near 1060 nm operate with optical-to-optical power-conversion efficiency of about 66%. State-of-the-art fiber-coupled pump diodes near 975 nm operate with about 50% electrical-to-fiber-coupled optical power conversion efficiency at 25C heatsink temperature. Therefore, the total system electrical-to-optical power conversion efficiency is about 33%. As a result, a 50-kW fiber laser will generate 75 kW of heat at the pump module and 25 kW at the fiber laser module with a total waste heat of 100 kW. It is evident that three times as much waste heat is generated at the pump module. While improving the efficiency of the diodes primarily reduces the input power requirement, increasing the operating temperature primarily reduces the size and weight for thermal management systems. We will discuss improvement in diode laser design, thermal resistance of the package as well as improvement in fiber-coupled optical-to-optical efficiency to achieve high efficiency at higher operating temperature. All of these factors have a far-reaching implication in terms of significantly improving the overall SWAP requirements thus enabling DEW-class fiber lasers on airborne and other platforms.

  8. Effects of ventilation-heating control strategies for early weaning pig barns on energy consumption and 3-D temperature distributions

    Energy Technology Data Exchange (ETDEWEB)

    Choiniere, Y. [Les Consultants Yves Choiniere, St-Cesaire, PQ (Canada); Laberge, B. [Thevco Electronique Inc., St-Hubert, PQ (Canada)

    1995-07-01

    A ventilation control chamber was built for a modern livestock barn at Alfred College to measure temperature distribution, humidity, and propane and electricity consumption. Performance of the control systems on ambient temperature distribution and energy consumption was analyzed. Tests were conducted with and without recirculation ducts. Results showed that the use of recirculation ducts reduced the floor to ceiling temperature gradients. Propane consumption was reduced by 20 per cent with the use of the recirculation duct. 3 tabs., 11 figs.

  9. Low-Temperature Thermal Energy Storage Program. Annual progress report, October 1977--September 1978

    Energy Technology Data Exchange (ETDEWEB)

    Brunton, G.D.; Eissenberg, D.M.; Kedl, R.J.

    1979-05-01

    The Low-Temperature Thermal Energy Storage (LTTES) Program is part of a national effort to develop means for reducing United States dependence on oil and natural gas as primary energy sources. To this end, LTTES addresses the development of advanced sensible and latent heat storage technologies that permit substitution by solar or off-peak electrical energies or permit conservation by recovery and reuse of waste heat. Emphasis is on applying these technologies to heating and cooling of buildings. As the LTTES program continued to mature, a number of technologies were identified for development emphasis, including (1) seasonal storage of hot and cold water from waste or natural sources in aquifers, (2) short-term or daily storage of heat or coolness from solar or off-peak electrical sources in phase-change materials, and (3) recovery and reuse of rejected industrial heat through thermal storage. These areas have been further divided into three major and four minor activities; significant accomplishments are reported for each.

  10. Energy consumption and control response evaluations of AODV routing in WSANs for building-temperature control.

    Science.gov (United States)

    Booranawong, Apidet; Teerapabkajorndet, Wiklom; Limsakul, Chusak

    2013-06-27

    The main objective of this paper is to investigate the effects of routing protocols on wireless sensor and actuator networks (WSANs), focusing on the control system response and the energy consumption of nodes in a network. We demonstrate that routing algorithms designed without considering the relationship between communication and control cannot be appropriately used in wireless networked control applications. For this purpose, an ad-hoc on-demand distance vector (AODV) routing, an IEEE 802.15.4, and a building-temperature control system are employed for this exploration. The findings from our scenarios show that the AODV routing can select a path with a high traffic load for data transmission. It takes a long time before deciding to change a new route although it experiences the unsuccessful transmission of packets. As a result, the desirable control target cannot be achieved in time, and nodes consume more energy due to frequent packet collisions and retransmissions. Consequently, we propose a simple routing solution to alleviate these research problems by modifying the original AODV routing protocol. The delay-threshold is considered to avoid any congested connection during routing procedures. The simulation results demonstrate that our solution can be appropriately applied in WSANs. Both the energy consumption and the control system response are improved.

  11. Energy Consumption and Control Response Evaluations of AODV Routing in WSANs for Building-Temperature Control

    Directory of Open Access Journals (Sweden)

    Chusak Limsakul

    2013-06-01

    Full Text Available The main objective of this paper is to investigate the effects of routing protocols on wireless sensor and actuator networks (WSANs, focusing on the control system response and the energy consumption of nodes in a network. We demonstrate that routing algorithms designed without considering the relationship between communication and control cannot be appropriately used in wireless networked control applications. For this purpose, an ad-hoc on-demand distance vector (AODV routing, an IEEE 802.15.4, and a building-temperature control system are employed for this exploration. The findings from our scenarios show that the AODV routing can select a path with a high traffic load for data transmission. It takes a long time before deciding to change a new route although it experiences the unsuccessful transmission of packets. As a result, the desirable control target cannot be achieved in time, and nodes consume more energy due to frequent packet collisions and retransmissions. Consequently, we propose a simple routing solution to alleviate these research problems by modifying the original AODV routing protocol. The delay-threshold is considered to avoid any congested connection during routing procedures. The simulation results demonstrate that our solution can be appropriately applied in WSANs. Both the energy consumption and the control system response are improved.

  12. Impact of the temperature dependency of fiberglass insulation R-value on cooling energy use in buildings

    Energy Technology Data Exchange (ETDEWEB)

    Levinson, R.; Akbari, H.; Gartland, L.

    1996-08-01

    Building energy models usually employ a constant, room-temperature-measured value for the thermal resistance of fiberglass roof insulation. In summer, however, the mean temperature of roof insulation can rise significantly above room temperature, lowering the insulation`s thermal resistance by 10% to 20%. Though the temperature dependence of the thermal resistance of porous materials like fiberglass has been extensively studied, it is difficult to theoretically predict the variation with temperature of a particular fiberglass blanket, from first principles. Heat transfer within fiberglass is complicated by the presence of three significant mechanisms - conduction through air, conduction through the glass matrix, and radiative exchange within the matrix - and a complex, unknown internal geometry. Purely theoretical models of fiberglass heat transfer assume highly simplified matrix structures and require typically-unavailable information about the fiberglass, such as its optical properties. There is also a dearth of useful experimental data. While the thermal resistances of many individual fiberglass samples have been measured, there is only one practical published table of thermal resistance vs. both temperature and density. Data from this table was incorporated in the DOE-2 building energy model. DOE-2 was used to simulate the roof surface temperature, roof heat flux, and cooling energy consumption of a school bungalow whose temperature and energy use had been monitored in 1992. The DOE-2 predictions made with and without temperature variation of thermal conductivity were compared to measured values. Simulations were also run for a typical office building. Annual cooling energy loads and annual peak hourly cooling powers were calculated for the office building using both fixed and variable thermal conductivities, and using five different climates. The decrease in the R-value of the office building`s roof led to a 2% to 4% increase in annual cooling energy load.

  13. The Effects of Mean Radiant Temperature on Thermal Comfort, Energy Consumption and Control – A Critical Overview

    NARCIS (Netherlands)

    V. Soebarto; J. van Hoof; E. Halawa

    2014-01-01

    Halawa, E., van Hoof, J., Soebarto, V. (2014) The Effects of Mean Radiant Temperature on Thermal Comfort, Energy Consumption and Control – A Critical Overview. Renewable & Sustainable Energy Review 37:907-918 doi: 10.1016/j.rser.2014.05.040

  14. Accuracy of the Temperature-Vegetation Dryness Index using MODIS under water-limited vs. energy-limited evapotranspiration conditions

    DEFF Research Database (Denmark)

    Garcia, Monica; Fernández, N.; Villagarcía, L.

    2014-01-01

    Water deficit indices based on the spatial relationship between surface temperature (Ts) and NDVI, known as triangle approaches, are widely used for drought monitoring. However, their application has been recently questioned when the main factor limiting evapotranspiration is energy. Even though...... water is the main control in dryland ecosystems, these can also undergo periods of energy and temperature limitation. In this paper we aimed to: (i) evaluate the TVDI (Temperature-Vegetation Dryness Index) to estimate water deficits (e.g. ratio between actual and potential evapotranspiration), and heat...

  15. Development and Performance Evaluation of High Temperature Concrete for Thermal Energy Storage for Solar Power Generation

    Energy Technology Data Exchange (ETDEWEB)

    Selvam, R. Panneer; Hale, Micah; Strasser, Matt

    2013-03-31

    Thermal energy can be stored by the mechanism of sensible or latent heat or heat from chemical reactions. Sensible heat is the means of storing energy by increasing the temperature of the solid or liquid. Since the concrete as media cost per kWhthermal is $1, this seems to be a very economical material to be used as a TES. This research is focused on extending the concrete TES system for higher temperatures (500 °C to 600 °C) and increasing the heat transfer performance using novel construction techniques. To store heat at high temperature special concretes are developed and tested for its performance. The storage capacity costs of the developed concrete is in the range of $0.91-$3.02/kWhthermal. Two different storage methods are investigated. In the first one heat is transported using molten slat through a stainless steel tube and heat is transported into concrete block through diffusion. The cost of the system is higher than the targeted DOE goal of $15/kWhthermal. The increase in cost of the system is due to stainless steel tube to transfer the heat from molten salt to the concrete blocks.The other method is a one-tank thermocline system in which both the hot and cold fluid occupy the same tank resulting in reduced storage tank volume. In this model, heated molten salt enters the top of the tank which contains a packed bed of quartzite rock and silica sand as the thermal energy storage (TES) medium. The single-tank storage system uses about half the salt that is required by the two-tank system for a required storage capacity. This amounts to a significant reduction in the cost of the storage system. The single tank alternative has also been proven to be cheaper than the option which uses large concrete modules with embedded heat exchangers. Using computer models optimum dimensions are determined to have an round trip efficiency of 84%. Additionally, the cost of the structured concrete thermocline configuration provides the TES

  16. Estimating morning changes in land surface temperature from MODIS day/night land surface temperature: Applications for surface energy balance modeling

    Science.gov (United States)

    Observations of land surface temperature (LST) are crucial for the monitoring of surface energy fluxes from satellite. Methods that require high temporal resolution LST observations (e.g., from geostationary orbit) can be difficult to apply globally because several geostationary sensors are required...

  17. Energy-Based Tetrahedron Sensor for High-Temperature, High-Pressure Environments

    Science.gov (United States)

    Gee, Kent L.; Sommerfeldt, Scott D.; Blotter, Jonathan D.

    2012-01-01

    An acoustic energy-based probe has been developed that incorporates multiple acoustic sensing elements in order to obtain the acoustic pressure and three-dimensional acoustic particle velocity. With these quantities, the user can obtain various energy-based quantities, including acoustic energy density, acoustic intensity, and acoustic impedance. In this specific development, the probe has been designed to operate in an environment characterized by high temperatures and high pressures as is found in the close vicinity of rocket plumes. Given these capabilities, the probe is designed to be used to investigate the acoustic conditions within the plume of a rocket engine or jet engine to facilitate greater understanding of the noise generation mechanisms in those plumes. The probe features sensors mounted inside a solid sphere. The associated electronics for the probe are contained within the sphere and the associated handle for the probe. More importantly, the design of the probe has desirable properties that reduce the bias errors associated with determining the acoustic pressure and velocity using finite sum and difference techniques. The diameter of the probe dictates the lower and upper operating frequencies for the probe, where accurate measurements can be acquired. The current probe design implements a sphere diameter of 1 in. (2.5 cm), which limits the upper operating frequency to about 4.5 kHz. The sensors are operational up to much higher frequencies, and could be used to acquire pressure data at higher frequencies, but the energy-based measurements are limited to that upper frequency. Larger or smaller spherical probes could be designed to go to lower or higher frequency range

  18. Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

    Directory of Open Access Journals (Sweden)

    Li Benkai

    2016-08-01

    Full Text Available Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL. This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that (1 castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient; (2 palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient; (3 MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil; (4 viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils; (5 although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature; (6 saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and (7 a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy

  19. Crossed, Small-Deflection Energy Analyzer for Wind/Temperature Spectrometer

    Science.gov (United States)

    Herrero, Federico A.; Finne, Theodore T.

    2010-01-01

    Determination of neutral winds and ion drifts in low-Earth-orbit missions requires measurements of the angular and energy distributions of the flux of neutrals and ions entering the satellite from the ram direction. The magnitude and direction of the neutral-wind (or ion-drift) determine the location of the maximum in the angular distribution of the flux. Knowledge of the angle of maximum flux with respect to satellite coordinates (pointing) is essential to determine the wind (or ion-drift) vector. The crossed Small-Deflection Energy Analyzer (SDEA) spectrometer (see Figure 1) occupies minimal volume and consumes minimal power. Designed for upper atmosphere/ionosphere investigations at Earth altitudes above 100 km, the spectrometer operates by detecting the angular and energy distributions of neutral atoms/molecules and ions in two mutually perpendicular planes. In this configuration, the two detection planes actually cross at the spectrometer center. It is possible to merge two SDEAs so they share a common optical axis and alternate measurements between two perpendicular planes, and reduce the number of ion sources from two to one. This minimizes the volume and footprint significantly and reduces the ion source power by a factor of two. The area of the entrance aperture affects the number of ions detected/second and also determines the energy resolution. Thermionic emitters require heater power of about 100 mW to produce 1 mA of electron beam current. Typically, electron energy is about 100 eV and requires a 100-V supply for electron acceleration to supply an additional 100 mW of power. Thus, ion source power is at most 200 mW. If two ion sources were to be used, the ion source power would be, at most, 400 mW. Detector power, deflection voltage power, and microcontroller and other functions require less than 150 mW. A WTS (wind/ temperature spectrometer) with two separate optical axes would consume about 650 mW, while the crossed SDEA described here consumes about

  20. Field test analysis of concentrator photovoltaic system focusing on average photon energy and temperature

    Science.gov (United States)

    Husna, Husyira Al; Ota, Yasuyuki; Minemoto, Takashi; Nishioka, Kensuke

    2015-08-01

    The concentrator photovoltaic (CPV) system is unique and different from the common flat-plate PV system. It uses a multi-junction solar cell and a Fresnel lens to concentrate direct solar radiation onto the cell while tracking the sun throughout the day. The cell efficiency could reach over 40% under high concentration ratio. In this study, we analyzed a one year set of environmental condition data of the University of Miyazaki, Japan, where the CPV system was installed. Performance ratio (PR) was discussed to describe the system’s performance. Meanwhile, the average photon energy (APE) was used to describe the spectrum distribution at the site where the CPV system was installed. A circuit simulator network was used to simulate the CPV system electrical characteristics under various environmental conditions. As for the result, we found that the PR of the CPV systems depends on the APE level rather than the cell temperature.

  1. Low-temperature aluminum reduction of graphene oxide, electrical properties, surface wettability, and energy storage applications.

    Science.gov (United States)

    Wan, Dongyun; Yang, Chongyin; Lin, Tianquan; Tang, Yufeng; Zhou, Mi; Zhong, Yajuan; Huang, Fuqiang; Lin, Jianhua

    2012-10-23

    Low-temperature aluminum (Al) reduction is first introduced to reduce graphene oxide (GO) at 100-200 °C in a two-zone furnace. The melted Al metal exhibits an excellent deoxygen ability to produce well-crystallized reduced graphene oxide (RGO) papers with a low O/C ratio of 0.058 (Al-RGO), compared with 0.201 in the thermally reduced one (T-RGO). The Al-RGO papers possess outstanding mechanical flexibility and extremely high electrical conductivities (sheet resistance R(s) ~ 1.75 Ω/sq), compared with 20.12 Ω/sq of T-RGO. More interestingly, very nice hydrophobic nature (90.5°) was observed, significantly superior to the reported chemically or thermally reduced papers. These enhanced properties are attributed to the low oxygen content in the RGO papers. During the aluminum reduction, highly active H atoms from H(2)O reacted with melted Al promise an efficient oxygen removal. This method was also applicable to reduce graphene oxide foams, which were used in the GO/SA (stearic acid) composite as a highly thermally conductive reservoir to hold the phase change material for thermal energy storage. The Al-reduced RGO/SnS(2) composites were further used in an anode material of lithium ion batteries possessing a higher specific capacity. Overall, low-temperature Al reduction is an effective method to prepare highly conductive RGO papers and related composites for flexible energy conversion and storage device applications.

  2. Quasiharmonic analysis of protein energy landscapes from pressure-temperature molecular dynamics simulations

    Science.gov (United States)

    Rodgers, Jocelyn M.; Hemley, Russell J.; Ichiye, Toshiko

    2017-09-01

    Positional fluctuations of an atom in a protein can be described as motion in an effective local energy minimum created by the surrounding protein atoms. The dependence of atomic fluctuations on both temperature (T) and pressure (P) has been used to probe the nature of these minima, which are generally described as harmonic in experiments such as x-ray crystallography and neutron scattering. Here, a quasiharmonic analysis method is presented in which the P-T dependence of atomic fluctuations is in terms of an intrinsic isobaric thermal expansivity αP and an intrinsic isothermal compressibility κT. The method is tested on previously reported mean-square displacements from P-T molecular dynamics simulations of lysozyme, which were interpreted to have a pressure-independent dynamical transition Tg near 200 K and a change in the pressure dependence near 480 MPa. Our quasiharmonic analysis of the same data shows that the P-T dependence can be described in terms of αP and κT where below Tg, the temperature dependence is frozen at the Tg value. In addition, the purported transition at 480 MPa is reinterpreted as a consequence of the pressure dependence of Tg and the quasiharmonic frequencies. The former also indicates that barrier heights between substates are pressure dependent in these data. Furthermore, the insights gained from this quasiharmonic analysis, which was of the energy landscape near the native state of a protein, suggest that similar analyses of other simulations may be useful in understanding such phenomena as pressure-induced protein unfolding.

  3. Thermal behavior of latent thermal energy storage unit using two phase change materials: Effects of HTF inlet temperature

    Directory of Open Access Journals (Sweden)

    Fouzi Benmoussa

    2017-09-01

    Full Text Available This work presents a numerical study of the thermal behavior of shell-and-tube latent thermal energy storage (LTES unit using two phase change materials (PCMs. The heat transfer fluid (HTF flow through the inner tube and transfer the heat to PCMs. First, a mathematical model is developed based on the enthalpy formulation and solved through the governing equations. Second, the effects of HTF inlet temperature on the unsteady temperature evolution of PCMs, the total energy stored evolution as well as the total melting time is studied. Numerical results show that for all HTF inlet temperature, melting rate of PCM1 is the fastest and that of PCM2 is the slowest; increasing the HTF inlet temperature considerably increases the temperature evolution of PCMs. The maximum energy stored is observed in PCM2 with high melting temperature and high specific heat; heat storage capacity is large for high HTF inlet temperature. When the HTF inlet temperature increases from 338 K to 353 K, decreasing degree of melting time of PCM2 is the biggest from 1870 s to 490 s, which reduces about 73.8%; decreasing degree of melting time of PCM1 is the smallest from 530 s to 270 s, which reduces about 49.1%.

  4. Evaluation of annual efficiencies of high temperature central receiver concentrated solar power plants with thermal energy storage.

    Energy Technology Data Exchange (ETDEWEB)

    Ehrhart, Brian David; Gill, David Dennis

    2013-07-01

    The current study has examined four cases of a central receiver concentrated solar power plant with thermal energy storage using the DELSOL and SOLERGY computer codes. The current state-of-the-art base case was compared with a theoretical high temperature case which was based on the scaling of some input parameters and the estimation of other parameters based on performance targets from the Department of Energy SunShot Initiative. This comparison was done for both current and high temperature cases in two configurations: a surround field with an external cylindrical receiver and a north field with a single cavity receiver. There is a fairly dramatic difference between the design point and annual average performance, especially in the solar field and receiver subsystems, and also in energy losses due to the thermal energy storage being full to capacity. Additionally, there are relatively small differences (<2%) in annual average efficiencies between the Base and High Temperature cases, despite an increase in thermal to electric conversion efficiency of over 8%. This is due the increased thermal losses at higher temperature and operational losses due to subsystem start-up and shut-down. Thermal energy storage can mitigate some of these losses by utilizing larger thermal energy storage to ensure that the electric power production system does not need to stop and re-start as often, but solar energy is inherently transient. Economic and cost considerations were not considered here, but will have a significant impact on solar thermal electric power production strategy and sizing.

  5. Trace species detection: Spectroscopy and molecular energy transfer at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Gray, J.A. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    Monitoring the concentration of trace species such as atomic and molecular free radicals is essential in forming predictive models of combustion processes. LIF-based techniques have the necessary sensitivity for concentration and temperature measurements but have limited accuracy due to collisional quenching in combustion applications. The goal of this program is to use spectroscopic and kinetic measurements to quantify nonradiative and collisional effects on LIF signals and to develop new background-free alternatives to LIF. The authors have measured the natural linewidth of several OH A-X (3,0) rotational transitions to determine predissociation lifetimes in the upper state, which were presumed to be short compared to quenching lifetimes, and as a result, quantitative predictions about the applicability of predissociation fluorescence methods at high pressures are made. The authors are investigating collisional energy transfer in the A-state of NO. Quenching rates which enable direct corrections to NO LIF quantum yields at high temperature were calculations. These quenching rates are now being used in studies of turbulence/chemistry interactions. The authors have measured the electric dipole moment {mu} of excited-state NO using Stark quantum-beat spectroscopy. {mu} is an essential input to a harpoon model which predicts quenching efficiencies for NO (A) by a variety of combustion-related species. The authors are developing new coherent multiphoton techniques for measurements of atomic hydrogen concentration in laboratory flames to avoid the quenching problems associated with previous multiphoton LIF schemes.

  6. Accurate potential energy curve for helium dimer retrieved from viscosity coefficient data at very low temperatures

    Science.gov (United States)

    Costa, Éderson D.'M.; Lemes, Nelson H. T.; Braga, João P.

    2017-12-01

    The long range potential of helium-helium interaction, which requires accurate ab initio calculation, due to the small value of the potential depth, approximately 11 K (9 . 5 × 10-4 eV = 0 . 091 kJ / mol) at 2.96 Å, will be obtained in this study by an alternative technique. This work presents a robust and consistent procedure that provides the long range potential directly from experimental data. However, it is difficult to obtain experimental data containing information regarding such a small potential depth. Thereby, sensitivity analysis will be used to circumvent this difficulty, from which viscosity data at lower temperatures (< 5 K) were chosen as appropriate data to be used to retrieve the potential function between 3 and 4 Å. The linear relationship between the potential energy function and the viscosity coefficient will be established under quantum assumptions and the Bose-Einstein statistics. The use of quantum theory is essential, since the temperatures are below 5 K. The potential obtained in this study describes the viscosity with an average error of 1.7% that is less than the experimental error (5%), with the results being similar to those obtained for recent ab initio potentials.

  7. Phase changing nanocomposites for low temperature thermal energy storage and release

    Directory of Open Access Journals (Sweden)

    A. Dorigato

    2017-09-01

    Full Text Available The aim of this paper is to develop new elastomeric phase change materials (PCM for the thermal energy storage/release below room temperature. In particular, poly(cyclooctene (PCO/paraffin blends filled with various concentrations of carbon nanotubes (CNTs, were prepared by a melt compounding process. The microstructural, thermo-mechanical and electrical properties of the resulting materials were investigated. The microstructure of these materials was characterized by the presence of paraffin domains inside the PCO, and CNTs were located only inside the paraffin domains in forms of aggregated clusters. DSC tests evidenced the existence of two distinct crystallization peaks at –10 and at 6 °C, respectively associated to the paraffin and the PCO phases, indicating that both the polymeric constituents are thermally active below room temperature. Moreover, CNT addition did not substantially alter the melting/crystallization properties of the material. Noticeable improvements of the mechanical properties and of the electrical conductivity with respect to the neat PCO/paraffin blend could be obtained upon CNT addition, and also thermal conductivity/diffusivity values were considerably enhanced above the percolation threshold. Finite element modeling demonstrated the efficacy of the prepared nanocomposites for applications in the thermal range from –30 to 6 °C.

  8. Development of Energy-Efficient Cryogenic Leads with High Temperature Superconducting Films on Ceramic Substrates

    Science.gov (United States)

    Pan, A. V.; Fedoseev, S. A.; Shcherbakova, O. V.; Golovchanskiy, I. A.; Zhou, S.; Dou, S. X.; Webber, R. J.; Mukhanov, O. A.; Yamashita, T.; Taylor, R.

    High temperature superconductor (HTS) material can be used for the implementation of high-speed low-heat conduction data links to transport digital data from 4 K superconductor integrated circuits to higher-temperature parts of computing systems. In this work, we present a conceptual design of energy efficient interface and results in fabricating such HTS leads. Initial calculations have shown that the microstrip line cable geometry for typical materials employed in production of HTS thin films can be a two-layered film for which the two layers of about 10 cm long are separated by an insulation layer with as low permittivity as possible. With this architecture in mind, the pulsed laser deposition process has been designed in a 45 cm diameter vacuum chamber to incorporate an oscillating sample holder with homogeneous substrate heating up to 900°C, while the laser plume is fixed. This design has allowed us to produce 200 nm to 500 nm thick, 7 cm to 10 cm long YBa2Cu3O7 thin films with the homogeneous critical temperature (Tc) of about 90 K. The critical current density (Jc) of the short samples obtained from the long sample is of (2 ± 1) × 1010 A/m2. Lines of 3-100 μm wide have been successfully patterned along the length of the samples in order to directly measure the Tc and Jc values over the entire length of the samples, as well as to attempt the structuring of multichannel data lead prototype.

  9. Economic study of low temperature geothermal energy in Lassen and Modoc counties, California

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-04-01

    The purpose of this study was to investigate the feasibility of using low cost, low temperature geothermal energy in job-producing industries to increase employment and encourage economic development. The study, encompassing all of Lassen and modoc Counties, was to be site-specific, referencing candidate geothermal applications to known hot wells and springs as previously determined, or to new wells with specific characteristics as defined in the Scope of Work. The emphasis was to be placed on economically practical and readily achievable applications from known resources, thus complimenting the recently completed ERDA-Susanville Study where a designated community was used as a ''laboratory'' in which land-use planning, institutional aspects, geological assessments, technical modeling and socioeconomic impacts were all examined in overview. During the course of the study, monthly progress reports were prepared and reviewed with the Commission so that emphasis on particular features of study could be changed as necessary to reflect updated findings and to redirect efforts into additional areas of potential promise as they became apparent. In this manner, a degree of flexibility was maintained which allowed a more comprehensive study than would have been otherwise possible. Although the report generates both positive and negative findings in specific areas of investigation, it is felt that the overall long term prognosis for geothermal energy stimulus to industry in the area is excellent.

  10. High Temperature Electrolysis for Hydrogen Production from Nuclear Energy – TechnologySummary

    Energy Technology Data Exchange (ETDEWEB)

    J. E. O' Brien; C. M. Stoots; J. S. Herring; M. G. McKellar; E. A. Harvego; M. S. Sohal; K. G. Condie

    2010-02-01

    The Department of Energy, Office of Nuclear Energy, has requested that a Hydrogen Technology Down-Selection be performed to identify the hydrogen production technology that has the best potential for timely commercial demonstration and for ultimate deployment with the Next Generation Nuclear Plant (NGNP). An Independent Review Team has been assembled to execute the down-selection. This report has been prepared to provide the members of the Independent Review Team with detailed background information on the High Temperature Electrolysis (HTE) process, hardware, and state of the art. The Idaho National Laboratory has been serving as the lead lab for HTE research and development under the Nuclear Hydrogen Initiative. The INL HTE program has included small-scale experiments, detailed computational modeling, system modeling, and technology demonstration. Aspects of all of these activities are included in this report. In terms of technology demonstration, the INL successfully completed a 1000-hour test of the HTE Integrated Laboratory Scale (ILS) technology demonstration experiment during the fall of 2008. The HTE ILS achieved a hydrogen production rate in excess of 5.7 Nm3/hr, with a power consumption of 18 kW. This hydrogen production rate is far larger than has been demonstrated by any of the thermochemical or hybrid processes to date.

  11. Hydrogen from biomass gas steam reforming for low temperature fuel cell: energy and exergy analysis

    Directory of Open Access Journals (Sweden)

    A. Sordi

    2009-03-01

    Full Text Available This work presents a method to analyze hydrogen production by biomass gasification, as well as electric power generation in small scale fuel cells. The proposed methodology is the thermodynamic modeling of a reaction system for the conversion of methane and carbon monoxide (steam reforming, as well as the energy balance of gaseous flow purification in PSA (Pressure Swing Adsorption is used with eight types of gasification gases in this study. The electric power is generated by electrochemical hydrogen conversion in fuel cell type PEMFC (Proton Exchange Membrane Fuel Cell. Energy and exergy analyses are applied to evaluate the performance of the system model. The simulation demonstrates that hydrogen production varies with the operation temperature of the reforming reactor and with the composition of the gas mixture. The maximum H2 mole fraction (0.6-0.64 mol.mol-1 and exergetic efficiency of 91- 92.5% for the reforming reactor are achieved when gas mixtures of higher quality such as: GGAS2, GGAS4 and GGAS5 are used. The use of those gas mixtures for electric power generation results in lower irreversibility and higher exergetic efficiency of 30-30.5%.

  12. Creep Behavior of High Temperature Alloys for Generation IV Nuclear Energy Systems

    Science.gov (United States)

    Wen, Xingshuo

    The Very High Temperature Reactor (VHTR) is one of the leading concepts of the Generation IV nuclear reactor development, which is the core component of Next Generation Nuclear Plant (NGNP). The major challenge in the research and development of NGNP is the performance and reliability of structure materials at high temperature. Alloy 617, with an exceptional combination of high temperature strength and oxidation resistance, has been selected as a primary candidate material for structural use, particularly in Intermediate Heat Exchanger (IHX) which has an outlet temperature in the range of 850 to 950°C and an inner pressure from 5 to 20MPa. In order to qualify the material to be used at the operation condition for a designed service life of 60 years, a comprehensive scientific understanding of creep behavior at high temperature and low stress regime is necessary. In addition, the creep mechanism and the impact factors such as precipitates, grain size, and grain boundary characters need to be evaluated for the purpose of alloy design and development. In this study, thermomechanically processed specimens of alloy 617 with different grain sizes were fabricated, and creep tests with a systematic test matrix covering the temperatures of 850 to 1050°C and stress levels from 5 to 100MPa were conducted. Creep data was analyzed, and the creep curves were found to be unconventional without a well-defined steady-state creep. Very good linear relationships were determined for minimum creep rate versus stress levels with the stress exponents determined around 3-5 depending on the grain size and test condition. Activation energies were also calculated for different stress levels, and the values are close to 400kJ/mol, which is higher than that for self-diffusion in nickel. Power law dislocation climb-glide mechanism was proposed as the dominant creep mechanism in the test condition regime. Dynamic recrystallization happening at high strain range enhanced dislocation climb and

  13. Potential of energy harvesting in barium titanate based laminates from room temperature to cryogenic/high temperatures: measurements and linking phase field and finite element simulations

    Science.gov (United States)

    Narita, Fumio; Fox, Marina; Mori, Kotaro; Takeuchi, Hiroki; Kobayashi, Takuya; Omote, Kenji

    2017-11-01

    This paper studies the energy harvesting characteristics of piezoelectric laminates consisting of barium titanate (BaTiO3) and copper (Cu) from room temperature to cryogenic/high temperatures both experimentally and numerically. First, the output voltages of the piezoelectric BaTiO3/Cu laminates were measured from room temperature to a cryogenic temperature (77 K). The output power was evaluated for various values of load resistance. The results showed that the maximum output power density is approximately 2240 nW cm‑3. The output voltages of the BaTiO3/Cu laminates were also measured from room temperature to a higher temperature (333 K). To discuss the output voltages of the BaTiO3/Cu laminates due to temperature changes, phase field and finite element simulations were combined. A phase field model for grain growth was used to generate grain structures. The phase field model was then employed for BaTiO3 polycrystals, coupled with the time-dependent Ginzburg–Landau theory and the oxygen vacancies diffusion, to calculate the temperature-dependent piezoelectric coefficient and permittivity. Using these properties, the output voltages of the BaTiO3/Cu laminates from room temperature to both 77 K and 333 K were analyzed by three dimensional finite element methods, and the results are presented for several grain sizes and oxygen vacancy densities. It was found that electricity in the BaTiO3 ceramic layer is generated not only through the piezoelectric effect caused by a thermally induced bending stress but also by the temperature dependence of the BaTiO3 piezoelectric coefficient and permittivity.

  14. High energy storage density over a broad temperature range in sodium bismuth titanate-based lead-free ceramics.

    Science.gov (United States)

    Yang, Haibo; Yan, Fei; Lin, Ying; Wang, Tong; Wang, Fen

    2017-08-18

    A series of (1-x)Bi0.48La0.02Na0.48Li0.02Ti0.98Zr0.02O3-xNa0.73Bi0.09NbO3 ((1-x)LLBNTZ-xNBN) (x = 0-0.14) ceramics were designed and fabricated using the conventional solid-state sintering method. The phase structure, microstructure, dielectric, ferroelectric and energy storage properties of the ceramics were systematically investigated. The results indicate that the addition of Na0.73Bi0.09NbO3 (NBN) could decrease the remnant polarization (P r ) and improve the temperature stability of dielectric constant obviously. The working temperature range satisfying TCC 150 °C ≤±15% of this work spans over 400 °C with the compositions of x ≥ 0.06. The maximum energy storage density can be obtained for the sample with x = 0.10 at room temperature, with an energy storage density of 2.04 J/cm(3) at 178 kV/cm. In addition, the (1-x)LLBNTZ-xNBN ceramics exhibit excellent energy storage properties over a wide temperature range from room temperature to 90 °C. The values of energy storage density and energy storage efficiency is 0.91 J/cm(3) and 79.51%, respectively, for the 0.90LLBNTZ-0.10NBN ceramic at the condition of 100 kV/cm and 90 °C. It can be concluded that the (1-x)LLBNTZ-xNBN ceramics are promising lead-free candidate materials for energy storage devices over a broad temperature range.

  15. An improved potential energy surface and multi-temperature quasiclassical trajectory calculations of N2 + N2 dissociation reactions.

    Science.gov (United States)

    Bender, Jason D; Valentini, Paolo; Nompelis, Ioannis; Paukku, Yuliya; Varga, Zoltan; Truhlar, Donald G; Schwartzentruber, Thomas; Candler, Graham V

    2015-08-07

    Accurate modeling of high-temperature hypersonic flows in the atmosphere requires consideration of collision-induced dissociation of molecular species and energy transfer between the translational and internal modes of the gas molecules. Here, we describe a study of the N2 + N2⟶N2 + 2N and N2 + N2⟶4N nitrogen dissociation reactions using the quasiclassical trajectory (QCT) method. The simulations used a new potential energy surface for the N4 system; the surface is an improved version of one that was presented previously. In the QCT calculations, initial conditions were determined based on a two-temperature model that approximately separates the translational-rotational temperature from the vibrational temperature of the N2 diatoms. Five values from 8000 K to 30,000 K were considered for each of the two temperatures. Over 2.4 × 10(9) trajectories were calculated. We present results for ensemble-averaged dissociation rate constants as functions of the translational-rotational temperature T and the vibrational temperature T(v). The rate constant depends more strongly on T when T(v) is low, and it depends more strongly on T(v) when T is low. Quasibound reactant states contribute significantly to the rate constants, as do exchange processes at higher temperatures. We discuss two sets of runs in detail: an equilibrium test set in which T = T(v) and a nonequilibrium test set in which T(v) energy and a minor loss of rotational energy. In the nonequilibrium test set, as T(v) decreases while T is fixed, higher-j molecules contribute more significantly to the dissociation rate, dissociating trajectories tend to result in a greater rotational energy loss, and the dissociation probability's dependence on v weakens. In this way, as T(v) decreases, rotational energy appears to compensate for the decline in average vibrational energy in promoting dissociation. In both the equilibrium and nonequilibrium test sets, in every case, the average total internal energy loss in the

  16. Effective Energy Transfer via Plasmon-Activated High-Energy Water Promotes Its Fundamental Activities of Solubility, Ionic Conductivity, and Extraction at Room Temperature

    Science.gov (United States)

    Yang, Chih-Ping; Chen, Hsiao-Chien; Wang, Ching-Chiung; Tsai, Po-Wei; Ho, Chia-Wen; Liu, Yu-Chuan

    2015-12-01

    Water is a ubiquitous solvent in biological, physical, and chemical processes. Unique properties of water result from water’s tetrahedral hydrogen-bonded (HB) network (THBN). The original THBN is destroyed when water is confined in a nanosized environment or localized at interfaces, resulting in corresponding changes in HB-dependent properties. In this work, we present an innovative idea to validate the reserve energy of high-energy water and applications of high-energy water to promote water’s fundamental activities of solubility, ionic conductivity, and extraction at room temperature. High-energy water with reduced HBs was created by utilizing hot electrons with energies from the decay of surface plasmon excited at gold (Au) nanoparticles (NPs). Compared to conventional deionized (DI) water, solubilities of alkali metal-chloride salts in high-energy water were significantly increased, especially for salts that release heat when dissolved. The ionic conductivity of NaCl in high-energy water was also markedly higher, especially when the electrolyte’s concentration was extremely low. In addition, antioxidative components, such as polyphenols and 2,3,5,4’-tetrahydroxystilbene-2-O-beta-d-glucoside (THSG) from teas, and Polygonum multiflorum (PM), could more effectively be extracted using high-energy water. These results demonstrate that high-energy water has emerged as a promising innovative solvent for promoting water’s fundamental activities via effective energy transfer.

  17. HIDROKONVERSI KATALITIK RESIDU MINYAK BUMI: PENGARUH TEMPERATUR DAN WAKTU REAKSI

    Directory of Open Access Journals (Sweden)

    Hartiniati Hartiniati

    2012-02-01

    Full Text Available Uji terhadap proses hidro-konversi katalitik residu petroleum dari unit refinery Plaju, Palembang dilakukan dengan menggunakan reaktor-batch berpengaduk (autoclave 1 liter pada kondisi standar: tekanan awal hidrogen 12 MPa dan rasio sulfur terhadap besi = 2.0. Studi dilakukan untuk melihat pengaruh perubahan temperatur dari 430, 450, dan 470oC serta waktu reaksi 30, 60, 90 menit terhadap distribusi produk dan jumlah konsumsi hidrogen. Hasil studi menunjukkan bahwa produk minyak, CO, CO2 dan hidrokarbon naik secara signifikan dengan naiknya temperatur dan waktu reaksi, namun sebaliknya produk cair bawah (liquid bottom cenderung turun. Pada kajian ini juga ditemukan bahwa konsumsi hidrogen naik dengan bertambahnya produk minyak, sehingga penggunaan hidrogen lebih efisien. Dengan demikian disimpulkan bahwa proses hidro-konversi katalitik dapat diterapkan pada residue petroleum untuk meningkatkan nilai tambah/kualitasnya. 

  18. A review on potential use of low-temperature water in the urban environment as a thermal-energy source

    Science.gov (United States)

    Laanearu, J.; Borodinecs, A.; Rimeika, M.; Palm, B.

    2017-10-01

    The thermal-energy potential of urban water sources is largely unused to accomplish the up-to-date requirements of the buildings energy demands in the cities of Baltic Sea Region. A reason is that the natural and excess-heat water sources have a low temperature and heat that should be upgraded before usage. The demand for space cooling should increase in near future with thermal insulation of buildings. There are a number of options to recover heat also from wastewater. It is proposed that a network of heat extraction and insertion including the thermal-energy recovery schemes has potential to be broadly implemented in the region with seasonally alternating temperature. The mapping of local conditions is essential in finding the suitable regions (hot spots) for future application of a heat recovery schemes by combining information about demands with information about available sources. The low-temperature water in the urban environment is viewed as a potential thermal-energy source. To recover thermal energy efficiently, it is also essential to ensure that it is used locally, and adverse effects on environment and industrial processes are avoided. Some characteristics reflecting the energy usage are discussed in respect of possible improvements of energy efficiency.

  19. The effects of pressure and temperature on the exchange energy of a parabolic quantum dot under a magnetic field

    Directory of Open Access Journals (Sweden)

    Faten Bzour

    2017-11-01

    Full Text Available The combined effects of pressure and temperature on the energy levels of a parabolic GaAs quantum dot under a magnetic field have been studied. The exact diagonalization method was used to solve the two-electron quantum dot Hamiltonian and to obtain the eigenenergies. In addition, we investigated the effects of pressure and temperature on the singlet-triplet exchange energy (J=ET−Es of the quantum dot as a function of a magnetic field. The magnetic field-parabolic confinement (ωc−ω0 phase diagram of the quantum dot was calculated. The comparisons show that our results are in very good agreement with the previously published works. Keywords: Quantum dot, Exact diagonalization method, Pressure, Temperature, Exchange energy

  20. Frequency, moisture content, and temperature dependent dielectric properties of potato starch related to drying with radio-frequency/microwave energy.

    Science.gov (United States)

    Zhu, Zhuozhuo; Guo, Wenchuan

    2017-08-24

    To develop advanced drying methods using radio-frequency (RF) or microwave (MW) energy, dielectric properties of potato starch were determined using an open-ended coaxial-line probe and network analyzer at frequencies between 20 and 4,500 MHz, moisture contents between 15.1% and 43.1% wet basis (w.b.), and temperatures between 25 and 75 °C. The results showed that both dielectric constant (ε') and loss factor (ε″) were dependent on frequency, moisture content, and temperature. ε' decreased with increasing frequency at a given moisture content or temperature. At low moisture contents (≤25.4% w.b.) or low temperatures (≤45 °C), ε″ increased with increasing frequency. However, ε″ changed from decrease to increase with increasing frequency at high moisture contents or temperatures. At low temperatures (25-35 °C), both ε' and ε″ increased with increasing moisture content. At low moisture contents (15.1-19.5% w.b.), they increased with increasing temperature. The change trends of ε' and ε″ were different and dependent on temperature and moisture content at their high levels. The penetration depth (d p ) decreased with increasing frequency. RF treatments may provide potential large-scale industrial drying application for potato starch. This research offers useful information on dielectric properties of potato starch related to drying with electromagnetic energy.

  1. The role of coupling on the statistical properties of the energy fluxes between stochastic systems at different temperatures

    Science.gov (United States)

    Bérut, A.; Imparato, A.; Petrosyan, A.; Ciliberto, S.

    2016-05-01

    We experimentally study the statistical properties of the energy fluxes in two systems whose components are kept at different temperatures. The first system under consideration is an electric circuit which is composed by two resistances, kept at different temperatures and connected by a capacitance (conservative coupling) which couples the thermal noise of the two resistances. The other system is composed by two Brownian particles, trapped with optical tweezers, interacting through a dissipative hydrodynamic coupling. The particles are subjected to an effective temperature difference obtained by random forcing the position of one trap. In these two systems we measure the properties of the energy flowing between the two reservoirs. The role on these properties of the coupling and of the method used to produce the highest temperature is analyzed.

  2. Influence of fermentation temperature on the content of fatty acids in low energy milk-based kombucha products

    OpenAIRE

    Malbaša, Radomir V.; Vitas, Jasmina S.; Lončar, Eva S.; Kravić, Snežana Ž.

    2011-01-01

    The aim of this study was to investigate the influence of fermentation temperature on the fatty acids content in low energy milk-based products obtained by kombucha inoculums with herbal teas. In this investigation low energy milk-based kombucha products were produced from milk with 0.8% milk fat using 10% (v/v) kombucha inoculums cultivated on winter savory, peppermint, stinging nettle and wild thyme. The process of fermentation was conducted at two temperatures: 40°C and 43°C. Ferment...

  3. Room temperature phosphorimetric determination of bromate in flour based on energy transfer.

    Science.gov (United States)

    Menendez-Miranda, Mario; Fernandez-Argüelles, Maria T; Costa-Fernandez, Jose M; Pereiro, Rosario; Sanz-Medel, Alfredo

    2013-11-15

    Determination of bromate ions in contaminated flour samples by using a room temperature phosphorescence (RTP) optosensor is described. The optosensor is based on the non-radiative energy transfer from α-bromonaphthalene (a phosphorescent molecule insensitive to the presence of the analyte) acting as donor, to an energy acceptor bromate-sensitive molecule (trifluoperazine hydrochloride). The RTP emission of the selected donor greatly overlaps with the absorption spectrum of the acceptor, resulting in a decrease of the measured signal as the concentration of bromate ions increases. A simple and general procedure is proposed to carry out the incorporation of both the donor and acceptor molecules in an appropriate solid material (sensing phase) through the co-immobilization of the species in a sol-gel inorganic matrix. The optimum amounts of the sol-gel precursors, including silica precursors, type of catalysis, and concentrations of donor and acceptor molecules, have been evaluated in order to obtain the best analytical features of the proposed optosensor for bromate determination. The highly stable developed sensing phase shows a selective and reversible response towards bromate even in presence of dissolved oxygen (a well-known quencher of the RTP). The calibration graphs were linear up to 200 mg L(-1), with a detection limit for bromate dissolved in aqueous medium of 0.2 mg L(-1). Sample throughput of the proposed optosensor was about 18 measurements h(-1). Application of the developed sensing phase was successfully proved for the detection of bromate ions in commercial flours, obtaining good recoveries. © 2013 Elsevier B.V. All rights reserved.

  4. Temperature dependence of exciton peak energies in ZnS, ZnSe, and ZnTe epitaxial films

    Science.gov (United States)

    Pässler, R.; Griebl, E.; Riepl, H.; Lautner, G.; Bauer, S.; Preis, H.; Gebhardt, W.; Buda, B.; As, D. J.; Schikora, D.; Lischka, K.; Papagelis, K.; Ves, S.

    1999-10-01

    High-quality ZnS, ZnSe, and ZnTe epitaxial films were grown on (001)-GaAs-substrates by molecular beam epitaxy. The 1s-exciton peak energy positions have been determined by absorption measurements from 2 K up to about room temperature. For ZnS and ZnSe additional high-temperature 1s-exciton energy data were obtained by reflectance measurements performed from 300 up to about 550 K. These complete E1s(T) data sets are fitted using a recently developed analytical model. The high-temperature slopes of the individual E1s(T) curves and the effective phonon temperatures of ZnS, ZnSe, and ZnTe are found to scale almost linearly with the corresponding zero-temperature energy gaps and the Debye temperatures, respectively. Various ad hoc formulas of Varshni type, which have been invoked in recent articles for numerical simulations of restricted E1s(T) data sets for cubic ZnS, are discussed.

  5. Impact of different temperatures on survival and energy metabolism in the Asian citrus psyllid, Diaphorina citri Kuwayama.

    Science.gov (United States)

    El-Shesheny, Ibrahim; Hijaz, Faraj; El-Hawary, Ibrahim; Mesbah, Ibrahim; Killiny, Nabil

    2016-02-01

    Temperature influences the life history and metabolic parameters of insects. Asian citrus psyllid (ACP), Diaphorina citri is a tropical and subtropical pest. ACP invaded new regions around the world and threatened the citrus industry as a vector for Huanglongbing (HLB) disease. ACP is widely distributed and can survive high (up to 45 °C) and low temperatures (as low as -6 °C). The precise mechanism of temperature tolerance in ACP is poorly understood. We investigated adult survival, cellular energy balance, gene expression, and nucleotide and sugar-nucleotide changes under the effect of different temperature regimes (0 °C to 45 °C with 5 °C intervals). The optimum temperatures for survival were 20 and 25 °C. Low temperatures of 0 °C and 5 °C caused 50% mortality after 2 and 4 days respectively, while one day at high temperature (40 °C and 45 °C) caused more than 95% mortality. The lowest quantity of ATP (3.69 ± 1.6 ng/insect) and the maximum ATPase enzyme activities (57.43 ± 7.6 μU/insect) were observed at 25 °C. Correlation between ATP quantities and ATPase activity was negative. Gene expression of hsp 70, V-type proton ATPase catalytic subunit A and ATP synthase α subunit matched these results. Twenty-four nucleotides and sugar-nucleotides were quantified using HPLC in ACP adults maintained at low, high, and optimum temperatures. The nucleotide profiles were different among treatments. The ratios between AMP:ATP and ADP:ATP were significantly decreased and positively correlated to adults survival, whereas the adenylate energy charge was increased in response to low and high temperatures. Exploring energy metabolic regulation in relation with adult survival might help in understanding the physiological basis of how ACP tolerates newly invaded regions. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Energy budget during lactation in striped hamsters at different ambient temperatures.

    Science.gov (United States)

    Zhao, Zhi-Jun

    2011-03-15

    The combination of two stressors, lactation and cold, is suggested to be an excellent model for testing the factors limiting sustained energy intake (SusEI). Limits to SusEI during peak lactation may be imposed peripherally by the capacity of mammary glands to produce milk or may be driven by the ability of animals to dissipate body heat. To distinguish between the two mechanisms, body mass change, food intake, reproductive output (using litter size and mass) and serum prolactin (PRL) levels were measured in striped hamsters lactating at 23, 30 and 5°C. Resting metabolic rate (RMR) during late lactation was also measured. Female hamsters lactating at 5°C showed significantly lower change in body mass, but had higher food intake and RMR than females at 23 and 30°C. Asymptotic food intake averaged 14.6±0.4, 14.5±0.7 and 16.2±0.5 g d(-1) for females at 23, 30 and 5°C, respectively. The females at 5°C had 11.4% higher asymptotic food intake than females at 23 and 30°C (F(2,51)=3.3, P<0.05, Tukey's HSD, P<0.05). No significant differences in litter size and PRL levels were observed between the three groups; however, litter mass at 5°C was lower by 19.7 and 19.8% than litter mass at 23 and 30°C on day 19 of lactation (F(2,51)=3.5, P<0.05, Tukey's HSD, P<0.05). Differences in the above parameters between 23 and 30°C were not significant. Litter mass was positively correlated with asymptotic food intake (23°C, r=0.60, P<0.05; 30°C, r=0.94, P<0.01; 5°C, r=0.77, P<0.01). These data suggested that females lactating at cold temperatures increased food intake to compensate for additional energy demands for thermogenesis, but they might not be capable of exporting more energy as milk to the pups, indicating a possible consistency with the peripheral hypothesis. However, the present results do not considerably distinguish the peripheral limitation hypothesis from the heat dissipation limits hypothesis.

  7. Gradient corrections to the kinetic energy density functional of a two-dimensional Fermi gas at finite temperature

    Science.gov (United States)

    van Zyl, B. P.; Berkane, K.; Bencheikh, K.; Farrell, A.

    2011-05-01

    We examine the leading-order semiclassical gradient corrections to the noninteracting kinetic-energy density functional of a two-dimensional Fermi gas by applying the extended Thomas-Fermi theory at finite temperature. We find a nonzero von Weizsäcker-like gradient correction, which in the high-temperature limit goes over to the functional form (ℏ2/24m)(∇ρ)2/ρ. Our work provides a theoretical justification for the inclusion of gradient corrections in applications of density-functional theory to inhomogeneous two-dimensional Fermi systems at any finite temperature.

  8. METHOD OF CALCULATION OF THE NON-STATIONARY TEMPERATURE FIELD INSIDE OF THERMAL PACKED BED ENERGY STORAGE

    Directory of Open Access Journals (Sweden)

    Ermuratschii V.V.

    2014-04-01

    Full Text Available e paper presents a method of the approximate calculation of the non-stationary temperature field inside of thermal packed bed energy storages with feasible and latent heat. Applying thermoelectric models and computational methods in electrical engineering, the task of computing non-stationary heat transfer is resolved with respect to third type boundary conditions without applying differential equations of the heat transfer. For sub-volumes of the energy storage the method is executed iteratively in spatiotemporal domain. Single-body heating is modeled for each sub-volume, and modeling conditions are assumed to be identical for remained bod-ies, located in the same sub-volume. For each iteration step the boundary conditions will be represented by re-sults at the previous step. The fulfillment of the first law of thermodynamics for system “energy storage - body” is obtained by the iterative search of the mean temperature of the energy storage. Under variable boundary con-ditions the proposed method maybe applied to calculating temperature field inside of energy storages with packed beds consisted of solid material, liquid and phase-change material. The method may also be employed to compute transient, power and performance characteristics of packed bed energy storages.

  9. Recovery of energy and nutrient resources from cattle paunch waste using temperature phased anaerobic digestion.

    Science.gov (United States)

    Jensen, Paul D; Mehta, Chirag M; Carney, Chris; Batstone, D J

    2016-05-01

    Cattle paunch is comprised of partially digested cattle feed, containing mainly grass and grain and is a major waste produced at cattle slaughterhouses contributing 20-30% of organic matter and 40-50% of P waste produced on-site. In this work, Temperature Phased Anaerobic Digestion (TPAD) and struvite crystallization processes were developed at pilot-scale to recover methane energy and nutrients from paunch solid waste. The TPAD plant achieved a maximum sustainable organic loading rate of 1-1.5kgCODm(-3)day(-1) using a feed solids concentration of approximately 3%; this loading rate was limited by plant engineering and not the biology of the process. Organic solids destruction (60%) and methane production (230LCH4kg(-1) VSfed) achieved in the plant were similar to levels predicted from laboratory biochemical methane potential (BMP) testing. Model based analysis identified no significant difference in batch laboratory parameters vs pilot-scale continuous parameters, and no change in speed or extent of degradation. However the TPAD process did result in a degree of process intensification with a high level of solids destruction at an average treatment time of 21days. Results from the pilot plant show that an integrated process enabled resource recovery at 7.8GJ/dry tonne paunch, 1.8kgP/dry tonne paunch and 1.0kgN/dry tonne paunch. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Direct-contact high-temperature thermal energy storage heat exchanger. Final subcontract report

    Energy Technology Data Exchange (ETDEWEB)

    Alario, J.; Brown, R.

    1983-09-01

    A 10-kWh scale model high-temperature direct-contact latent-heat-exchange thermal energy storage system was designed and fabricated. A research program was structured in three separate phases to permit: Phase I - the inspection and evaluation of the origin al hardware, which suffered extensive corrosion and damage in a previous experimental program; Phase II - redesign and fabrication of a modified system; and Phase III - detailed test evaluation. On the basis of the findings in Phase I, the design was modified to eliminate previous deficiencies. A test plan was also prepared that contained detailed information concerning instrumentation (type and location), measured parameters, and equipment operating procedures. Phase II entailed component procurement and fabrication, system assembly, and instrumentation. At the end of Phase II, the system was in a ready-for-test condition but the program was terminated before the start of the Phase III test evaluation. Since testing was never implemented, this report presents only the results for the design and fabrication phases of the program.

  11. Temperature phase transitions associated with local minima of energy in continous unbounded spins

    CERN Document Server

    Dobrovolny, B

    2004-01-01

    {\\footnotesize In this work we develop an alternative version of the theory of contour models adapted to continuous spins, $\\omega_{x}\\in {\\large{\\bf {R}}}$, located in sites, $x$ of a $d\\geq 2$ dimensional lattice ${\\large{\\bf Z^{d}}}$. \\\\ The spins interacting via nearest neighbors ferromagnetic interactions are embedded in a single spin potential $V$ similar to that, already, introduced by Dobrushin and Shlosman.\\\\ The potential $V$, has an ordered sequence $\\left( \\omega_{1}m_{q^{^{\\prime }}}$, $q< q^{^{\\prime }}$. \\item The distance between two successive minima is sufficiently great and the they are separated by a sufficiently heigh energy barrier. \\end{itemize} For all finite reciprocal temperature $\\beta$, satisfying $1\\leq \\beta <\\infty$, and for the mass $m_{n}$ ( corresponding to the $n^{th}$ minimum) large enough, we prove the Peierls condition, and we derive the phase diagram by proving that there exist sequences ($\\beta_{1},... ,\\beta_{N(n)}$) , $N(n)

  12. Temperature-dependent activation energy of electromigration in Cu/porous low-k interconnects

    Science.gov (United States)

    Zheng, Hui; Yin, Binfeng; Zhou, Ke; Chen, Leigang; Kuo, Chinte

    2017-08-01

    In this paper, it was reported that the Time-to-Failure (TTF) of electromigration (EM) in Cu/porous low-k interconnects deviated from the classical Black's Equation at 250-350 °C due to moisture invasion. The EM activation energy (Ea) was 1.003 eV at above 300 °C, whereas the apparent value reduced to be negative below 300 °C, being accompanied by significantly narrowed TTF distribution. The corresponding change in the failure mode was distinctly revealed, which indicated that the oxidation of Ta-based liner due to moisture invasion through the porous low-k contributed significantly and modestly to the EM failure below and above 300 °C. The mechanism of the liner oxidation was interpreted with the theory of field-assisted cation migration, which suggested the steep slowdown of the oxidation from 275 to 300 °C could be ascribed to the substantial decrease in the moisture concentration at the low-k/Ta oxide interface, most probably owing to significant suppression of adsorption and surface diffusion of chemisorbed moisture in the nanoporous low-k. The inconsistent EM behaviors at the lower and higher temperatures were thus interpreted by the competition of intrinsic and extrinsic EM controlled separately by Cu diffusion along the Cu/SiN-based cap layer interface and the moisture-damaged Cu/Ta interface.

  13. Transition Metal Coatings for Energy Conversion and Storage; Electrochemical and High Temperature Applications

    Science.gov (United States)

    Falola, Bamidele Daniel

    Energy storage provides sustainability when coupled with renewable but intermittent energy sources such as solar, wave and wind power, and electrochemical supercapacitors represent a new storage technology with high power and energy density. For inclusion in supercapacitors, transition metal oxide and sulfide electrodes such as RuO2, IrO2, TiS2, and MoS2 exhibit rapid faradaic electron-transfer reactions combined with low resistance. The pseudocapacitance of RuO2 is about 720 F/g, and is 100 times greater than double-layer capacitance of activated carbon electrodes. Due to the two-dimensional layered structure of MoS2, it has proven to be an excellent electrode material for electrochemical supercapacitors. Cathodic electrodeposition of MoS2 onto glassy carbon electrodes is obtained from electrolytes containing (NH4)2MoS 4 and KCl. Annealing the as-deposited Mo sulfide deposit improves the capacitance by a factor of 40x, with a maximum value of 360 F/g for 50 nm thick MoS2 films. The effects of different annealing conditions were investigated by XRD, AFM and charge storage measurements. The specific capacitance measured by cyclic voltammetry is highest for MoS2 thin films annealed at 500°C for 3h and much lower for films annealed at 700°C for 1 h. Inclusion of copper as a dopant element into electrodeposited MoS2 thin films for reducing iR drop during film charge/discharge is also studied. Thin films of Cu-doped MoS2 are deposited from aqueous electrolytes containing SCN-, which acts as a complexing agent to shift the cathodic Cu deposition potential, which is much more anodic than that of MoS2. Annealed, Cu-doped MoS2 films exhibit enhanced charge storage capability about 5x higher than undoped MoS2 films. Coal combustion is currently the largest single anthropogenic source of CO2 emissions, and due to the growing concerns about climate change, several new technologies have been developed to mitigate the problem, including oxyfuel coal combustion, which makes CO2

  14. Dual direction blower system powered by solar energy to reduce car cabin temperature in open parking condition

    Science.gov (United States)

    Hamdan, N. S.; Radzi, M. F. M.; Damanhuri, A. A. M.; Mokhtar, S. N.

    2017-10-01

    El-nino phenomenon that strikes Malaysia with temperature recorded more than 35°C can lead to extreme temperature rise in car cabin up to 80°C. Various problems will arise due to this extreme rising of temperature such as the occupant are vulnerable to heat stroke, emission of benzene gas that can cause cancer due to reaction of high temperature with interior compartments, and damage of compartments in the car. The current solution available to reduce car cabin temperature including tinted of window and portable heat rejection device that are available in the market. As an alternative to reduce car cabin temperature, this project modifies the car’s air conditioning blower motor into dual direction powered by solar energy and identifies its influence to temperature inside the car, parked under scorching sun. By reducing the car cabin temperature up to 10°C which equal to 14% of reduction in the car cabin temperature, this simple proposed system aims to provide comfort to users due to its capability in improving the quality of air and moisture in the car cabin.

  15. Excitation energy transfer in individual light-harvesting chlorosome from green photosynthetic bacterium Chloroflexus aurantiacus at cryogenic temperature

    Science.gov (United States)

    Saga, Yoshitaka; Tamiaki, Hitoshi; Shibata, Yutaka; Itoh, Shigeru

    2005-06-01

    The excitation energy transfer from bacteriochlorophyll(BChl)- c self-aggregates to energy-accepting BChl- a in proteins (baseplates) in an individual photosynthetic light-harvesting complex (chlorosome) of a green filamentous photosynthetic bacterium Chloroflexus aurantiacus was successfully observed at cryogenic temperature. The ratio of intensity of the fluorescence peak of BChl- a to that of BChl- c self-aggregates in individual chlorosomes, which demonstrated relative efficiency of the excitation energy transfer, was heterogeneous between 0.09 and 0.72. This suggests that excitonic interaction between BChl- c self-aggregates and BChl- a in baseplates was heterogeneous among individual chlorosomes.

  16. Using radiometric surface temperature for surface energy flux estimation in Mediterranean drylands from a two-source perspective

    Science.gov (United States)

    The recent paper by Morillas et al. [Morillas, L. et al. Using radiometric surface temperature for surface energy flux estimation in Mediterranean drylands from a two-source perspective, Remote Sens. Environ. 136, 234-246, 2013] evaluates the two-source model (TSM) of Norman et al. (1995) with revi...

  17. Electron energy distribution function, effective electron temperature, and dust charge in the temporal afterglow of a plasma

    Energy Technology Data Exchange (ETDEWEB)

    Denysenko, I. B.; Azarenkov, N. A. [School of Physics and Technology, V. N. Karazin Kharkiv National University, Svobody sq. 4, 61022 Kharkiv (Ukraine); Kersten, H. [Institut für Experimentelle und Angewandte Physik, Leibnizstr. 19, Kiel D-24098 (Germany)

    2016-05-15

    Analytical expressions describing the variation of electron energy distribution function (EEDF) in an afterglow of a plasma are obtained. Especially, the case when the electron energy loss is mainly due to momentum-transfer electron-neutral collisions is considered. The study is carried out for different EEDFs in the steady state, including Maxwellian and Druyvesteyn distributions. The analytical results are not only obtained for the case when the rate for momentum-transfer electron-neutral collisions is independent on electron energy but also for the case when the collisions are a power function of electron energy. Using analytical expressions for the EEDF, the effective electron temperature and charge of the dust particles, which are assumed to be present in plasma, are calculated for different afterglow durations. An analytical expression for the rate describing collection of electrons by dust particles for the case when the rate for momentum-transfer electron-neutral collisions is independent on electron energy is also derived. The EEDF profile and, as a result, the effective electron temperature and dust charge are sufficiently different in the cases when the rate for momentum-transfer electron-neutral collisions is independent on electron energy and when the rate is a power function of electron energy.

  18. Simultaneous application of microwave energy and hot air to whole drying process of apple slices: drying kinetics, modeling, temperature profile and energy aspect

    Science.gov (United States)

    Horuz, Erhan; Bozkurt, Hüseyin; Karataş, Haluk; Maskan, Medeni

    2017-09-01

    Drying kinetics, modeling, temperature profile and energy indices were investigated in apple slices during drying by a specially designed microwave-hot air domestic hybrid oven at the following conditions: 120, 150 and 180 W microwave powers coupled with 50, 60 and 70 °C air temperatures. Both sources of energy were applied simultaneously during the whole drying processes. The drying process continued until the moisture content of apple slices reached to 20% from 86.3% (wet basis, w.b). Drying times ranged from 330 to 800 min and decreased with increasing microwave power and air temperatures. The constant rate period was only observed at low microwave powers and air temperatures. Two falling rate periods were observed. Temperature of apple slices sharply increased within the first 60 min, then reached equilibrium with drying medium and finally increased at the end of the drying process. In order to describe drying behavior of apple slices nine empirical models were applied. The Modified Logistic Model fitted the best our experimental data (R 2 = 0.9955-0.9998; χ 2 = 3.46 × 10-5-7.85 × 10-4 and RMSE = 0.0052-0.0221). The effective moisture and thermal diffusivities were calculated by Fick's second law and ranged from 1.42 × 10-9 to 3.31 × 10-9 m2/s and 7.70 × 10-9 to 12.54 × 10-9 m2/s, respectively. The activation energy (Ea) values were calculated from effective moisture diffusivity (Deff), thermal diffusivity (α) and the rate constant of the best model (k). The Ea values found from these three terms were similar and varied from 13.04 to 33.52 kJ/mol. Energy consumption and specific energy requirement of the hybrid drying of apple slices decreased and energy efficiency of the drying system increased with increasing microwave power and air temperature. Apples can be dried rapidly and effectively by use of the hybrid technique.

  19. Suppression of Temperature Fluctuations and Energy Barrier Generation by Velocity Shear

    Science.gov (United States)

    Boedo, J. A.; Terry, P. W.; Gray, D.; Ivanov, R. S.; Conn, R. W.; Jachmich, S.; van Oost, G.; Textor Team

    2000-03-01

    First measurements of temperature fluctuations in a region of high velocity shear show that absolute and normalized fluctuation levels are reduced across the shear layer, a result that is consistent with weak parallel electron thermal conduction in the electron temperature dynamics. The concomitant reduction of temperature, density, and electric field fluctuations reduces the anomalous conducted and convected heat fluxes.

  20. Lowering district heating temperatures – Impact to system performance in current and future Danish energy scenarios

    DEFF Research Database (Denmark)

    Ommen, Torben; Markussen, Wiebke Brix; Elmegaard, Brian

    2016-01-01

    that primary fuel consumption is reduced approximately 5e7% at DH design temperatures of 60e70 C. Further reduction in DH temperatures resulted in opposing tendencies, as hot tap water requires electricity to reach the required temperatures. The results are network-specific, as they represent the given network...

  1. Temperature Dependence in Heterogeneous Nucleation with Application to the Direct Determination of Cluster Energy on Nearly Molecular Scale.

    Science.gov (United States)

    McGraw, Robert L; Winkler, Paul M; Wagner, Paul E

    2017-12-04

    A re-examination of measurements of heterogeneous nucleation of water vapor on silver nanoparticles is presented here using a model-free framework that derives the energy of critical cluster formation directly from measurements of nucleation probability. Temperature dependence is correlated with cluster stabilization by the nanoparticle seed and previously found cases of unusual increasing nucleation onset saturation ratio with increasing temperature are explained. A necessary condition for the unusual positive temperature dependence is identified, namely that the critical cluster be more stable, on a per molecule basis, than the bulk liquid to exhibit the effect. Temperature dependence is next examined in the classical Fletcher model, modified here to make the energy of cluster formation explicit in the model.  The contact angle used in the Fletcher model is identified as the microscopic contact angle, which can be directly obtained from heterogeneous nucleation experimental data by a recently developed analysis method. Here an equivalent condition, increasing contact angle with temperature, is found necessary for occurrence of unusual temperature dependence. Our findings have immediate applications to atmospheric particle formation and nanoparticle detection in condensation particle counters (CPCs).

  2. Molecular dynamics simulation of temperature effects on low energy near-surface cascades and surface damage in Cu

    Science.gov (United States)

    Zhu, Guo; Sun, Jiangping; Guo, Xiongxiong; Zou, Xixi; Zhang, Libin; Gan, Zhiyin

    2017-06-01

    The temperature effects on near-surface cascades and surface damage in Cu(0 0 1) surface under 500 eV argon ion bombardment were studied using molecular dynamics (MD) method. In present MD model, substrate system was fully relaxed for 1 ns and a read-restart scheme was introduced to save total computation time. The temperature dependence of damage production was calculated. The evolution of near-surface cascades and spatial distribution of adatoms at varying temperature were analyzed and compared. It was found that near-surface vacancies increased with temperature, which was mainly due to the fact that more atoms initially located in top two layers became adatoms with the decrease of surface binding energy. Moreover, with the increase of temperature, displacement cascades altered from channeling-like structure to branching structure, and the length of collision sequence decreased gradually, because a larger portion of energy of primary knock-on atom (PKA) was scattered out of focused chain. Furthermore, increasing temperature reduced the anisotropy of distribution of adatoms, which can be ascribed to that regular registry of surface lattice atoms was changed with the increase of thermal vibration amplitude of surface atoms.

  3. Land surface temperature representativeness in a heterogeneous area through a distributed energy-water balance model and remote sensing data

    Directory of Open Access Journals (Sweden)

    C. Corbari

    2010-10-01

    Full Text Available Land surface temperature is the link between soil-vegetation-atmosphere fluxes and soil water content through the energy water balance. This paper analyses the representativeness of land surface temperature (LST for a distributed hydrological water balance model (FEST-EWB using LST from AHS (airborne hyperspectral scanner, with a spatial resolution between 2–4 m, LST from MODIS, with a spatial resolution of 1000 m, and thermal infrared radiometric ground measurements that are compared with the representative equilibrium temperature that closes the energy balance equation in the distributed hydrological model.

    Diurnal and nocturnal images are analyzed due to the non stable behaviour of the thermodynamic temperature and to the non linear effects induced by spatial heterogeneity.

    Spatial autocorrelation and scale of fluctuation of land surface temperature from FEST-EWB and AHS are analysed at different aggregation areas to better understand the scale of representativeness of land surface temperature in a hydrological process.

    The study site is the agricultural area of Barrax (Spain that is a heterogeneous area with a patchwork of irrigated and non irrigated vegetated fields and bare soil. The used data set was collected during a field campaign from 10 to 15 July 2005 in the framework of the SEN2FLEX project.

  4. Molecular dynamics simulation of temperature effects on low energy near-surface cascades and surface damage in Cu

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Guo; Sun, Jiangping; Guo, Xiongxiong; Zou, Xixi; Zhang, Libin; Gan, Zhiyin, E-mail: ganzhiyin@126.com

    2017-06-15

    The temperature effects on near-surface cascades and surface damage in Cu(0 0 1) surface under 500 eV argon ion bombardment were studied using molecular dynamics (MD) method. In present MD model, substrate system was fully relaxed for 1 ns and a read-restart scheme was introduced to save total computation time. The temperature dependence of damage production was calculated. The evolution of near-surface cascades and spatial distribution of adatoms at varying temperature were analyzed and compared. It was found that near-surface vacancies increased with temperature, which was mainly due to the fact that more atoms initially located in top two layers became adatoms with the decrease of surface binding energy. Moreover, with the increase of temperature, displacement cascades altered from channeling-like structure to branching structure, and the length of collision sequence decreased gradually, because a larger portion of energy of primary knock-on atom (PKA) was scattered out of focused chain. Furthermore, increasing temperature reduced the anisotropy of distribution of adatoms, which can be ascribed to that regular registry of surface lattice atoms was changed with the increase of thermal vibration amplitude of surface atoms.

  5. Temperature and energy effects on secondary electron emission from SiC ceramics induced by Xe17+ions.

    Science.gov (United States)

    Zeng, Lixia; Zhou, Xianming; Cheng, Rui; Wang, Xing; Ren, Jieru; Lei, Yu; Ma, Lidong; Zhao, Yongtao; Zhang, Xiaoan; Xu, Zhongfeng

    2017-07-25

    Secondary electron emission yield from the surface of SiC ceramics induced by Xe 17+ ions has been measured as a function of target temperature and incident energy. In the temperature range of 463-659 K, the total yield gradually decreases with increasing target temperature. The decrease is about 57% for 3.2 MeV Xe 17+ impact, and about 62% for 4.0 MeV Xe 17+ impact, which is much larger than the decrease observed previously for ion impact at low charged states. The yield dependence on the temperature is discussed in terms of work function, because both kinetic electron emission and potential electron emission are influenced by work function. In addition, our experimental data show that the total electron yield gradually increases with the kinetic energy of projectile, when the target is at a constant temperature higher than room temperature. This result can be explained by electronic stopping power which plays an important role in kinetic electron emission.

  6. Core-ion temperature measurement of the ADITYA tokamak using passive charge exchange neutral particle energy analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Pandya, Santosh P.; Ajay, Kumar; Mishra, Priyanka; Dhingra, Rajani D.; Govindarajan, J. [Institute for Plasma Research, Bhat, Gandhinagar 382 428, Gujarat (India)

    2013-02-15

    Core-ion temperature measurements have been carried out by the energy analysis of passive charge exchange (CX) neutrals escaping out of the ADITYA tokamak plasma (minor radius, a= 25 cm and major radius, R= 75 cm) using a 45 Degree-Sign parallel plate electrostatic energy analyzer. The neutral particle analyzer (NPA) uses a gas cell configuration for re-ionizing the CX-neutrals and channel electron multipliers (CEMs) as detectors. Energy calibration of the NPA has been carried out using ion-source and {Delta}E/E of high-energy channel has been found to be {approx}10%. Low signal to noise ratio (SNR) due to VUV reflections on the CEMs was identified during the operation of the NPA with ADITYA plasma discharges. This problem was rectified by upgrading the system by incorporating the additional components and arrangements to suppress VUV radiations and improve its VUV rejection capabilities. The noise rejection capability of the NPA was experimentally confirmed using a standard UV-source and also during the plasma discharges to get an adequate SNR (>30) at the energy channels. Core-ion temperature T{sub i}(0) during flattop of the plasma current has been measured to be up to 150 eV during ohmically heated plasma discharges which is nearly 40% of the average core-electron temperature (typically T{sub e}(0) {approx} 400 eV). The present paper describes the principle of tokamak ion temperature measurement, NPA's design, development, and calibration along with the modifications carried out for minimizing the interference of plasma radiations in the CX-spectrum. Performance of the NPA during plasma discharges and experimental results on the measurement of ion-temperature have also been reported here.

  7. A renewable energy scenario for Aalborg Municipality based on low-temperature geothermal heat, wind power and biomass

    DEFF Research Database (Denmark)

    Østergaard, Poul Alberg; Mathiesen, Brian Vad; Möller, Bernd

    2010-01-01

    Aalborg Municipality, Denmark, wishes to investigate the possibilities of becoming independent of fossil fuels. This article describes a scenario for supplying Aalborg Municipality’s energy needs through a combination of low-temperature geothermal heat, wind power and biomass. Of particular focus...... in the scenario is how low-temperature geothermal heat may be utilised in district heating (DH) systems. The analyses show that it is possible to cover Aalborg Municipality’s energy needs through the use of locally available sources in combination with significant electricity savings, heat savings, reductions...... in industrial fuel use and savings and fuel-substitutions in the transport sector. With biomass resources being finite, the two marginal energy resources in Aalborg are geothermal heat and wind power. If geothermal heat is utilised more, wind power may be limited and vice versa. The system still relies...

  8. Effect of Temperature and Pressure on Correlation Energy in a Triplet State of a Two Electron Spherical Quantum Dot

    Directory of Open Access Journals (Sweden)

    A. Rejo Jeice

    2013-09-01

    Full Text Available The combined effect of hydrostatic pressure and temperature on correlation energy in a triplet state of two electron spherical quantum dot with square well potential is computed. The result is presented taking GaAs dot as an example. Our result shows the correlation energies are inegative in the triplet state contrast to the singlet state ii it increases with increase in pressure  iiifurther decreases due to the application  of temperature iv it approaches zero as dot size approaches infinity and v it contribute 10% decrement in total confined energy to the narrow dots. All the calculations have been carried out with finite models and the results are compared with existing literature.

  9. Burning rate characteristics of energetic CMDB propellants (III). Effect of initial propellant temperature; Ko energy CMDB suishinyaku no nensho sokudo tokusei (III). Suishinyaku shoki ondo no koka

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, I. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1998-01-01

    In case of double-base properants, the temperature sensitivity of burning rate for this type of propellants having higher energy becomes smaller than that of propellants having lower energy. When the energy contained in propellants increases, or initial propellant temperatures increase, the burning surface temperature of propellant increases, therefore, the reaction in fizz zone is accelerated, the dark zone temperature increases, and the temperature gradient in fizz zone increases. This increase of temperature gradient increases the burning rate of propellant. In case of HMX-CMDB propellants, when the energy contained in propellants increases, or initial propellant temperatures decrease, the burning surface temperature of propellant decreases, therefore, the reaction in fizz zone is decelerated, the dark zone temperature decreases, and the temperature gradient in fizz zone decreases. This decrease of temperature gradient decreases the burning rate of propellant. As a result, it was clarified that the temperatures as common physical properties which had an effect of initial propellant temperatures on the burning rates were the burning surface temperature and the dark zone temperature. 22 refs., 12 figs., 2 tabs.

  10. Effects of Varroa destructor on temperature and humidity conditions and expression of energy metabolism genes in infested honeybee colonies.

    Science.gov (United States)

    Hou, C S; Li, B B; Deng, S; Diao, Q Y

    2016-09-23

    Varroa destructor mites pose an increasing global threat to the apicultural industry and agricultural ecology; however, the issue of whether certain environmental factors reflect the level of mite infection is far from resolved. Here, a wireless sensor network (WSN) system was used to examine how V. destructor, which has vital impacts on honeybee (Apis mellifera) health and survival, affects the temperature and humidity of honeybee hives in a field experiment. This approach may facilitate early identification of V. destructor in hives, and thus enable timely remedial action. Using quantitative PCR, we also evaluated the expression of two genes, adipokinetic hormone (AKH) and adipokinetic hormone receptor (AKHR).The results showed that temperature in highly infested broods was higher than that in broods with low infestation. Moreover, mite infection in honeybee colonies was positively correlated with temperature but negatively correlated with humidity (P Varroa infection not only causes changes in temperature inside honeybee colonies, but also affects the expression of honeybee energy metabolism genes.

  11. House Owners’ Interests and Actions in Relation to Indoor Temperature, Air Quality and Energy Use

    DEFF Research Database (Denmark)

    Knudsen, Henrik Nellemose; Andersen, Rune Korsholm; Hansen, Anders Rhiger

    2016-01-01

    in saving energy for the sake of the environment and for their own economy, and quite a lot of households indicate that they know their own energy consumption, though only few follow it closely. Thus being concerned about energy is not necessarily related to an interest in detailed feedback on one’s own...

  12. House Owners’ Interests and Actions in Relation to Indoor Temperature, Air Quality and Energy Consumption

    DEFF Research Database (Denmark)

    Knudsen, Henrik Nellemose; Andersen, Rune K.; Hansen, Anders Rhiger

    2016-01-01

    in saving energy for the sake of the environment and for their own economy, and quite a lot of households indicate that they know their own energy consumption, though only few follow it closely. Thus being concerned about energy is not necessarily related to an interest in detailed feedback on one’s own...

  13. Next-Generation Electrochemical Energy Materials for Intermediate Temperature Molten Oxide Fuel Cells and Ion Transport Molten Oxide Membranes.

    Science.gov (United States)

    Belousov, Valery V

    2017-02-21

    High temperature electrochemical devices such as solid oxide fuel cells (SOFCs) and oxygen separators based on ceramic materials are used for efficient energy conversion. These devices generally operate in the temperature range of 800-1000 °C. The high operating temperatures lead to accelerated degradation of the SOFC and oxygen separator materials. To solve this problem, the operating temperatures of these electrochemical devices must be lowered. However, lowering the temperature is accompanied by decreasing the ionic conductivity of fuel cell electrolyte and oxygen separator membrane. Therefore, there is a need to search for alternative electrolyte and membrane materials that have high ionic conductivity at lower temperatures. A great many opportunities exist for molten oxides as electrochemical energy materials. Because of their unique electrochemical properties, the molten oxide innovations can offer significant benefits for improving energy efficiency. In particular, the newly developed electrochemical molten oxide materials show high ionic conductivities at intermediate temperatures (600-800 °C) and could be used in molten oxide fuel cells (MOFCs) and molten oxide membranes (MOMs). The molten oxide materials containing both solid grains and liquid channels at the grain boundaries have advantages compared to the ceramic materials. For example, the molten oxide materials are ductile, which solves a problem of thermal incompatibility (difference in coefficient of thermal expansion, CTE). Besides, the outstanding oxygen selectivity of MOM materials allows us to separate ultrahigh purity oxygen from air. For their part, the MOFC electrolytes show the highest ionic conductivity at intermediate temperatures. To evaluate the potential of molten oxide materials for technological applications, the relationship between the microstructure of these materials and their transport and mechanical properties must be revealed. This Account summarizes the latest results on

  14. Temperature effect on first excited state energy and transition frequency of a strong-coupling polaron in a symmetry RbCl quantum dot

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Yong; Ding, Zhao-Hua; Xiao, Jing-Lin, E-mail: xiaojlin@126.com

    2014-07-01

    The first excited state energy, excitation energy and transition frequency of a strong-coupling polaron in a symmetric RbCl quantum dot (SRQD) are obtained by employing the linear combination operator and unitary transformation methods. Effects of temperature and confinement strength are taken into account. It is found that the first excited state energy, excitation energy and transition frequency are increasing functions of temperature and confinement strength.

  15. Temperature effect on first excited state energy and transition frequency of a strong-coupling polaron in a symmetry RbCl quantum dot

    Science.gov (United States)

    Sun, Yong; Ding, Zhao-Hua; Xiao, Jing-Lin

    The first excited state energy, excitation energy and transition frequency of a strong-coupling polaron in a symmetric RbCl quantum dot (SRQD) are obtained by employing the linear combination operator and unitary transformation methods. Effects of temperature and confinement strength are taken into account. It is found that the first excited state energy, excitation energy and transition frequency are increasing functions of temperature and confinement strength.

  16. The Role of Soya Oil Ester in Water-Based PCM for Low Temperature Cool Energy Storage

    Directory of Open Access Journals (Sweden)

    I. M. Rasta

    2016-01-01

    Full Text Available This study focuses on the preparation of the water-based phase change material (PCM with very small soya oil solution for low temperature latent heat thermal energy storage (LHTES. Soya oil ester is soluble very well in water and acts as nucleating agent for a novel solid-liquid PCM candidate that is suitable for low temperature cool storage in the range between −9°C and −6°C. Thermal energy storage properties of the water with very small soya oil ester solution were measured by T-history method. The experimental results show that very small amount of soya oil ester in water can lower the freezing point and trigger ice nucleation for elimination of the supercooling degree. The phase transition temperatures of the water-based PCMs with soya oil as nucleate agent were lower than those of individual water. The thermal properties make it potential PCM for LHTES systems used in low temperature cool energy storage applications.

  17. Constraints from the CMB temperature and other common observational data sets on variable dark energy density models

    Science.gov (United States)

    Jetzer, Philippe; Tortora, Crescenzo

    2011-08-01

    The thermodynamic and dynamical properties of a variable dark energy model with density scaling as ρx∝(1+z)m, z being the redshift, are discussed following the outline of Jetzer et al. [P. Jetzer, D. Puy, M. Signore, and C. Tortora, Gen. Relativ. Gravit. 43, 1083 (2011).GRGVA80001-770110.1007/s10714-010-1091-4]. These kinds of models are proven to lead to the creation/disruption of matter and radiation, which affect the cosmic evolution of both matter and radiation components in the Universe. In particular, we have concentrated on the temperature-redshift relation of radiation, which has been constrained using a very recent collection of cosmic microwave background (CMB) temperature measurements up to z˜3. For the first time, we have combined this observational probe with a set of independent measurements (Supernovae Ia distance moduli, CMB anisotropy, large-scale structure and observational data for the Hubble parameter), which are commonly adopted to constrain dark energy models. We find that, within the uncertainties, the model is indistinguishable from a cosmological constant which does not exchange any particles with other components. Anyway, while temperature measurements and Supernovae Ia tend to predict slightly decaying models, the contrary happens if CMB data are included. Future observations, in particular, measurements of CMB temperature at large redshift, will allow to give firmer bounds on the effective equation of state parameter weff of this kind of dark energy model.

  18. Effects of strain rate and elevated temperature on compressive flow stress and absorbed energy of polyimide foam

    Directory of Open Access Journals (Sweden)

    Horikawa K.

    2012-08-01

    Full Text Available In this study, at first, the effect of strain rate on the strength and the absorbed energy of polyimide foam was experimentally examined by carrying out a series of compression tests at various strain rates, from 10−3 to 103 s−1. This polyimide foam has open cell structure with small cell size of 0.3 ∼ 0.6 mm. In the measurement of impact load, a special load cell with a small part for sensing load was adopted. For the measurement of the displacement, a high-speed camera was used. It was found that the flow stress of polyimide foam and the absorbed energy up to a strain of 0.4 increased with the increase of the strain rates. Secondly, the effect of ambient temperature on the strength and absorbed energy of polyimide foam was also investigated by using a sprit Hopkinson pressure bar apparatus and testing at elevated temperatures of 100 and 200 ∘C. With the increase of temperature, the strength and absorbed energy decreased and the effect is smaller in dynamic tests than static tests.

  19. Combined influence of hydrostatic pressure and temperature on interband emission energy of impurity doped quantum dots in presence of noise

    Science.gov (United States)

    Bera, Aindrila; Ghosh, Manas

    2016-11-01

    We explore the profiles of interband emission energy (IEE) of impurity doped quantum dots (QDs) under the simultaneous influence of hydrostatic pressure (HP) and temperature (T) and in presence and absence of Gaussian white noise. Noise has been incorporated to the system additively and multiplicatively. In this regard, modulation of IEE by the variation of several other relevant quantities such as electric field, magnetic field, confinement potential, dopant location, dopant potential and aluminium concentration has also been investigated. Gradual alteration of HP and T affects IEE discernibly. Inclusion of noise has been found to enhance or deplete the IEE depending upon its mode of application. Moreover, under given conditions of temperature and pressure, the difference between the impurity-free ground state energy and the binding energy appears to be crucial in determining whether or not the profiles of IEE would resemble that of binding energy. The findings reveal fascinating role played by noise in tailoring the IEE of doped QD system under conspicuous presence of hydrostatic pressure and temperature.

  20. Reconnoitering the effect of shallow groundwater on land surface temperature and surface energy balance using MODIS and SEBS

    Directory of Open Access Journals (Sweden)

    F. Alkhaier

    2012-07-01

    Full Text Available The possibility of observing shallow groundwater depth and areal extent using satellite measurements can support groundwater models and vast irrigation systems management. Moreover, these measurements can help to include the effect of shallow groundwater on surface energy balance within land surface models and climate studies, which broadens the methods that yield more reliable and informative results. To examine the capacity of MODIS in detecting the effect of shallow groundwater on land surface temperature and the surface energy balance in an area within Al-Balikh River basin in northern Syria, we studied the interrelationship between in-situ measured water table depths and land surface temperatures measured by MODIS. We, also, used the Surface Energy Balance System (SEBS to calculate surface energy fluxes, evaporative fraction and daily evaporation, and inspected their relationships with water table depths. We found out that the daytime temperature increased while the nighttime temperature decreased when the depth of the water table increased. And, when the water table depth increased, net radiation, latent and ground heat fluxes, evaporative fraction and daily evaporation decreased, while sensible heat flux increased. This concords with the findings of a companion paper (Alkhaier et al., 2012. The observed clear relationships were the result of meeting both conditions that were concluded in the companion paper, i.e. high potential evaporation and big contrast in day-night temperature. Moreover, the prevailing conditions in this study area helped SEBS to yield accurate estimates. Under bare soil conditions and under the prevailing weather conditions, we conclude that MODIS is suitable for detecting the effect of shallow groundwater because it has proper imaging times and adequate sensor accuracy; nevertheless, its coarse spatial resolution is disadvantageous.

  1. Exploring connections between statistical mechanics and Green's functions for realistic systems. Temperature dependent entropy and internal energy from a self-consistent second-order Green's function

    CERN Document Server

    Welden, Alicia Rae; Zgid, Dominika

    2016-01-01

    Including finite-temperature effects into electronic structure calculations of semiconductors and metals is frequently necessary, but can become cumbersome using zero-temperature methods, which require an explicit evaluation of excited states to extend the approach to finite-temperature. Using a Matsubara Green's function formalism, it is easy to include the effects of temperature and to connect dynamic quantities such as the self-energy with static thermodynamic quantities such as the Helmholtz energy, entropy, and internal energy. We evaluate the thermodynamic quantities with a self-consistent Green's function where the self-energy is approximated to second-order (GF2). To validate our method, we benchmark it against finite temperature full configuration interaction (FCI) calculations for a hydrogen fluoride (HF) molecule and find excellent agreement at high temperatures and very good agreement at low temperatures. Then, we proceed to evaluate thermodynamic quantities for a one-dimension hydrogen solid at v...

  2. Electron attachment to POCl3: Measurement and theoretical analysis of rate constants and branching ratios as a function of gas pressure and temperature, electron temperature, and electron energy

    Science.gov (United States)

    Van Doren, Jane M.; Friedman, Jeffery F.; Miller, Thomas M.; Viggiano, A. A.; Denifl, S.; Scheier, P.; Märk, T. D.; Troe, J.

    2006-03-01

    Two experimental techniques, electron swarm and electron beam, have been applied to the problem of electron attachment to POCl3, with results indicating that there is a competition between dissociation of the resonant POCl3-* state and collisional stabilization of the parent anion. In the electron beam experiment at zero electron energy, the fragment ion POCl2- is the dominant ion product of attachment (96%), under single-collision conditions. Small amounts (˜2% each) of POCl3- and Cl - were observed. POCl3- and POCl2- ion products were observed only at zero electron energy, but higher-energy resonances were recorded for POCl-, Cl-, and Cl2- ion products. In the electron swarm experiment, which was carried out in 0.4-7Torr of He buffer gas, the parent anion branching ratio increased significantly with pressure and decreased with temperature. The electron attachment rate constant at 297K was measured to be (2.5±0.6)×10-7cm3s-1, with ion products POCl2- (71%) and POCl3- (29%) in 1Torr of He gas. The rate constant decreased as the electron temperature was increased above 1500K. Theory is developed for (a) the unimolecular dissociation of the nascent POCl3-* and (b) a stepladder collisional stabilization mechanism using the average energy transferred per collision as a parameter. These ideas were then used to model the experimental data. The modeling showed that D0o(Cl -POCl2-) and EA(POCl3) must be the same within ±0.03eV.

  3. High-Temperature Annealing Induced He Bubble Evolution in Low Energy He Ion Implanted 6H-SiC

    Science.gov (United States)

    Liu, Yu-Zhu; Li, Bing-Sheng; Zhang, Li

    2017-05-01

    Bubble evolution in low energy and high dose He-implanted 6H-SiC upon thermal annealing is studied. The -oriented 6H-SiC wafers are implanted with 15 keV helium ions at a dose of 1 × 10 17 cm -2 at room temperature. The samples with post-implantation are annealed at temperatures of 1073, 1173, 1273, and 1473 K for 30 min. He bubbles in the wafers are examined via cross-sectional transmission electron microscopy (XTEM) analysis. The results present that nanoscale bubbles are almost homogeneously distributed in the damaged layer of the as-implanted sample, and no significant change is observed in the He-implanted sample after 1073 K annealing. Upon 1193 K annealing, almost full recrystallization of He-implantation-induced amorphization in 6H-SiC is observed. In addition, the diameters of He bubbles increase obviously. With continually increasing temperatures to 1273 K and 1473 K, the diameters of He bubbles increase and the number density of lattice defects decreases. The growth of He bubbles after high temperature annealing abides by the Ostwald ripening mechanism. The mean diameter of He bubbles located at depths of 120-135 nm as a function of annealing temperature is fitted in terms of a thermal activated process which yields an activation energy of 1.914+0.236 eV. Supported by the National Natural Science Foundation of China under Grant No 11475229.

  4. The energy budget, thermogenic capacity and behavior in Swiss mice exposed to a consecutive decrease in temperatures.

    Science.gov (United States)

    Zhao, Zhi-Jun; Chi, Qing-Sheng; Cao, Jing; Han, Ying-Dong

    2010-12-01

    The limitation on sustainable energy intake (SusEI) is important because it establishes the upper energetic limit on the ability of animals to disperse, survive and reproduce. However, there are still arguments about what factors impose that limitation. Thermoregulation in cold environments imposes great energy demands on small mammals. A cold-exposed animal has been suggested to be a model suitable for testing these factors. Here, we examined the changes in food intake and digestible energy intake (DEI) as measures of SusEI, thermogenic capacity and behavioral patterns in Swiss mice exposed to consecutively lower ambient temperatures from 23 to -15°C. Cold-exposed mice showed significant decreases in body mass, fat content of the carcass and body temperature, and increases in DEI compared with controls. The time spent on feeding significantly increased with decreasing temperatures, and time spent on general activity decreased following cold exposure. Resting metabolic rate, nonshivering thermogenesis and serum tri-iodothyronine levels significantly increased in mice exposed to lower temperatures in comparison with controls, whereas these thermogenic variables were not significantly different between 0 and -15°C. It might suggest that SusEI in cold exposed Swiss mice was constrained peripherally by the capacity to produce heat and also by the ability to dissipate body heat, but to a different extent. Moderate cold exposure might result in a relaxation of the heat dissipation limit (HDL), allowing the animals to increase food intake to meet cold stress. When animals are exposed to severe cold, the thermogenenic capacity might reach a ceiling, failing to compensate for the heat loss and which would finally result in lower body temperature and considerable weight loss. This might indicate that the HDL was set at a higher level than peripheral limits for Swiss mice exposed to a consecutive decrease in ambient temperatures.

  5. Quantum mechanical free energy profiles with post-quantization restraints: Binding free energy of the water dimer over a broad range of temperatures

    Science.gov (United States)

    Bishop, Kevin P.; Roy, Pierre-Nicholas

    2018-03-01

    Free energy calculations are a crucial part of understanding chemical systems but are often computationally expensive for all but the simplest of systems. Various enhanced sampling techniques have been developed to improve the efficiency of these calculations in numerical simulations. However, the majority of these approaches have been applied using classical molecular dynamics. There are many situations where nuclear quantum effects impact the system of interest and a classical description fails to capture these details. In this work, path integral molecular dynamics has been used in conjunction with umbrella sampling, and it has been observed that correct results are only obtained when the umbrella sampling potential is applied to a single path integral bead post quantization. This method has been validated against a Lennard-Jones benchmark system before being applied to the more complicated water dimer system over a broad range of temperatures. Free energy profiles are obtained, and these are utilized in the calculation of the second virial coefficient as well as the change in free energy from the separated water monomers to the dimer. Comparisons to experimental and ground state calculation values from the literature are made for the second virial coefficient at higher temperature and the dissociation energy of the dimer in the ground state.

  6. Temperature measurements of micro-droplets using pulsed 2-color laser-induced fluorescence with MDR-enhanced energy transfer

    Science.gov (United States)

    Palmer, Johannes; Reddemann, Manuel A.; Kirsch, Valeri; Kneer, Reinhold

    2016-12-01

    In this work, a new measurement system is presented for studying temperature of micro-droplets by pulsed 2-color laser-induced fluorescence. Pulsed fluorescence excitation allows motion blur suppression and thus simultaneous measurements of droplet size, velocity and temperature. However, high excitation intensities of pulsed lasers lead to morphology-dependent resonances inside micro-droplets, which are accompanied by disruptive stimulated emission. Investigations showed that stimulated emission can be avoided by enhanced energy transfer via an additional dye. The suitability and accuracy of the new pulsed method are verified on the basis of a spectroscopic analysis and comparison to continuously excited 2-color laser-induced fluorescence.

  7. Development of High-Temperature Ferritic Alloys and Performance Prediction Methods for Advanced Fission Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    G. RObert Odette; Takuya Yamamoto

    2009-08-14

    Reports the results of a comprehensive development and analysis of a database on irradiation hardening and embrittlement of tempered martensitic steels (TMS). Alloy specific quantitative semi-empirical models were derived for the dpa dose, irradiation temperature (ti) and test (Tt) temperature of yield stress hardening (or softening) .

  8. Electrolytes for Use in High Energy Lithium-ion Batteries with Wide Operating Temperature Range

    Science.gov (United States)

    Smart, Marshall C.; Ratnakumar, B. V.; West, W. C.; Whitcanack, L. D.; Huang, C.; Soler, J.; Krause, F. C.

    2012-01-01

    Met programmatic milestones for program. Demonstrated improved performance with wide operating temperature electrolytes containing ester co-solvents (i.e., methyl butyrate) containing electrolyte additives in A123 prototype cells: Previously demonstrated excellent low temperature performance, including 11C rates at -30 C and the ability to perform well down to -60 C. Excellent cycle life at room temperature has been displayed, with over 5,000 cycles being demonstrated. Good high temperature cycle life performance has also been achieved. Demonstrated improved performance with methyl propionate-containing electrolytes in large capacity prototype cells: Demonstrated the wide operating temperature range capability in large cells (12 Ah), successfully scaling up technology from 0.25 Ah size cells. Demonstrated improved performance at low temperature and good cycle life at 40 C with methyl propionate-based electrolyte containing increasing FEC content and the use of LiBOB as an additive. Utilized three-electrode cells to investigate the electrochemical characteristics of high voltage systems coupled with wide operating temperature range electrolytes: From Tafel polarization measurements on each electrode, it is evident the NMC-based cathode displays poor lithium kinetics (being the limiting electrode). The MB-based formulations containing LiBOB delivered the best rate capability at low temperature, which is attributed to improved cathode kinetics. Whereas, the use of lithium oxalate as an additive lead to the highest reversible capacity and lower irreversible losses.

  9. Shallow groundwater effect on land surface temperature and surface energy balance under bare soil conditions: modeling and description

    Directory of Open Access Journals (Sweden)

    F. Alkhaier

    2012-07-01

    Full Text Available Understanding when and how groundwater affects surface temperature and energy fluxes is significant for utilizing remote sensing in groundwater studies and for integrating aquifers within land surface models. To investigate the shallow groundwater effect under bare soil conditions, we numerically exposed two soil profiles to identical metrological forcing. One of the profiles had shallow groundwater. The different responses that the two profiles manifested were inspected regarding soil moisture, temperature and energy balance at the land surface. The findings showed that the two profiles differed in three aspects: the absorbed and emitted amounts of energy, the portioning out of the available energy and the heat fluency in the soil. We concluded that due to their lower albedo, shallow groundwater areas reflect less shortwave radiation and consequently get a higher magnitude of net radiation. When potential evaporation demand is sufficiently high, a large portion of the energy received by these areas is consumed for evaporation. This increases the latent heat flux and reduces the energy that could have heated the soil. Consequently, lower magnitudes of both sensible and ground heat fluxes are caused to occur. The higher soil thermal conductivity in shallow groundwater areas facilitates heat transfer between the top soil and the subsurface, i.e. soil subsurface is more thermally connected to the atmosphere. For the reliability of remote sensors in detecting shallow groundwater effect, it was concluded that this effect can be sufficiently clear to be detected if at least one of the following conditions occurs: high potential evaporation and high contrast between day and night temperatures. Under these conditions, most day and night hours are suitable for shallow groundwater depth detection.

  10. State of the art on high temperature thermal energy storage for power generation. Part 1. Concepts, materials and modellization

    Energy Technology Data Exchange (ETDEWEB)

    Gil, Antoni; Medrano, Marc; Martorell, Ingrid; Cabeza, Luisa F. [GREA Innovacio Concurrent, Universitat de Lleida, Pere de Cabrera s/n, 25001-Lleida (Spain); Lazaro, Ana; Dolado, Pablo; Zalba, Belen [Instituto de Investigacion en Ingenieria de Aragon, I3A, Grupo de Ingenieria Termica y Sistemas Energeticos (GITSE), Dpto. Ingenieria Mecanica, Area de Maquinas y Motores Termicos, Universidad de Zaragoza, Campus Politecnico Rio Ebro, Edificio ' Agustin de Betancourt' , Maria de Luna s/n, 50018 Zaragoza (Spain)

    2010-01-15

    Concentrated solar thermal power generation is becoming a very attractive renewable energy production system among all the different renewable options, as it has have a better potential for dispatchability. This dispatchability is inevitably linked with an efficient and cost-effective thermal storage system. Thus, of all components, thermal storage is a key one. However, it is also one of the less developed. Only a few plants in the world have tested high temperature thermal energy storage systems. In this paper, the different storage concepts are reviewed and classified. All materials considered in literature or plants are listed. And finally, modellization of such systems is reviewed. (author)

  11. Development and characterization of high temperature, high energy density dielectric materials to establish routes towards power electronics capacitive devices

    Science.gov (United States)

    Shay, Dennis P.

    The maximum electrostatic energy density of a capacitor is a function of the relative permittivity (epsilonr) and the square of the dielectric breakdown strength (Eb). Currently, state-of-the art high temperature (>200 °C), SiC-based power electronics utilize CaZrO3-rich NP0/C0G-type capacitors, which have low relative permittivities of epsilonr ˜ 30-40, high breakdown strengths (> 1.0 MV/cm), and are chosen for their minimal change in energy storage with temperature. However, with operating temperatures exceeding the rated temperatures for such capacitors, there is an opportunity to develop new dielectric ceramics having higher energy densities and volumetric efficiencies at high temperatures (>200 °C) by utilizing higher permittivity dielectrics while maintaining high breakdown strengths via doping. The solid solution behavior of was characterized in order to determine the optimal composition for balancing permittivity and dielectric breakdown strength to obtain high energy densities at elevated temperatures. Characterization by X-ray diffraction (XRD) showed Vegard's law behavior across the solid solution with minimal 2nd phases. To determine a Ca(TixZr1-x)O3 composition that will also minimize electronic or band conduction, the optical properties of the Ca(TixZr1-x)O3 solid solution were investigated to identify a composition on the CaTiO3 - rich end of the solid solution with a large band gap. Both ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis) and spectroscopic ellipsometry were utilized to determine the Ca(TixZr1-x)O3 band gaps and optical properties. The resistivity at 250 °C scaled with the band gap energy across the solid solution. Comparing the current-voltage (I--V) behavior at 250 °C for Ca(Tix-yMnyZr0.2)O3 (CTZ + Mn) where x = 0.7, 0.8, 0.9, and y = 0.005, it was found that the Ca(Ti 0.795Mn0.005Zr0.2)O3 composition showed the lowest current density and a decrease in current density of 5 orders of magnitude compared to the un

  12. Low-Temperature Projects of the Department of Energy's Geothermal Technologies Program: Evaluation and Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Tom; Snyder, Neil; Gosnold, Will

    2016-10-23

    This paper discusses opportunities and challenges related to the technical and economic feasibility of developing power generation from geothermal resources at temperatures of 150 degrees C and lower. Insights from projects funded by the U.S. Department of Energy (DOE), Geothermal Technologies Office inform these discussions and provide the basis for some lessons learned to help guide decisions by DOE and the industry in further developing this resource. The technical basis for low-temperature geothermal energy is well established and the systems can be economic today in certain situations. However, these applications are far from a 'plug and play' product; successful development today requires a good knowledge of geothermal system design and operation.

  13. Low-Temperature Projects of the Department of Energy's Geothermal Technologies Program: Evaluation and Lessons Learned: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Williams, Tom; Snyder, Neil; Gosnold, Will

    2016-12-01

    This paper discusses opportunities and challenges related to the technical and economic feasibility of developing power generation from geothermal resources at temperatures of 150 degrees C and lower. Insights from projects funded by the U.S. Department of Energy (DOE), Geothermal Technologies Office inform these discussions and provide the basis for some lessons learned to help guide decisions by DOE and the industry in further developing this resource. The technical basis for low-temperature geothermal energy is well established and the systems can be economic today in certain situations. However, these applications are far from a 'plug and play' product; successful development today requires a good knowledge of geothermal system design and operation.

  14. A method for estimating the temperature in high energy density free electron laser experiments

    Energy Technology Data Exchange (ETDEWEB)

    Principi, Emiliano, E-mail: emiliano.principi@unicam.i [CNISM, Dipartimento di Fisica, Universita degli Studi di Camerino via Madonna delle Carceri, I-62032 Camerino (Italy); Ferrante, Carino; Filipponi, Adriano [Dipartimento di Fisica, Universita degli Studi dell' Aquila, Via Vetoio, I-67100 L' Aquila (Italy); Bencivenga, Filippo; D' Amico, Francesco; Masciovecchio, Claudio [Synchrotron ELETTRA, Strada Statale 14-I-34149 Basovizza, Trieste (Italy); Di Cicco, Andrea [CNISM, Dipartimento di Fisica, Universita degli Studi di Camerino via Madonna delle Carceri, I-62032 Camerino (Italy); IMPMC, Universite Paris 6, CNRS, 140 rue de Lourmel, 75015 Paris (France)

    2010-09-21

    Present and forthcoming free electron laser (FEL) large scale facilities deliver high fluence ultrafast soft and hard X-ray pulses able to create and probe warm dense matter (WDM). Proper diagnostic for basic physical quantities, like temperature and density, is necessary, but the short lifetime of the WDM state (few ps) makes their measurements a challenging task. In this work we propose a method to estimate the WDM temperature using the experimental information from a slow temperature pyrometric probe exploiting the properties of the heat diffusion equation. Numerical simulations show that for typical thin foil samples, a temperature measurement with 1-10{mu}s temporal resolution at the distance of about 300-500{mu}m from the beam center contains sufficient information to retrieve the initial spatial temperature distribution with sufficient accuracy providing information on the temperature reached in the WDM regime. The inversion of the experimental information is obtained by means of a Bayesian approach exploiting a Metropolis Monte Carlo numerical procedure. The model and calculations presented in this work provide the theoretical background for the development of a device for temperature diagnostics of the TIMEX end-station at the Fermi-Elettra FEL facility.

  15. Novel Methods of Tritium Sequestration: High Temperature Gettering and Separation Membrane Materials Discovery for Nuclear Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Franglin [Univ. of South Carolina, Columbia, SC (United States); Sholl, David [Georgia Inst. of Technology, Atlanta, GA (United States); Brinkman, Kyle [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Lyer, Ratnasabapathy [Claflin Univ., Orangeburg, SC (United States); Iyer, Ratnasabapathy [Claflin Univ., Orangeburg, SC (United States); Reifsnider, Kenneth [Univ. of South Carolina, Columbia, SC (United States)

    2015-01-22

    This project is aimed at addressing critical issues related to tritium sequestration in next generation nuclear energy systems. A technical hurdle to the use of high temperature heat from the exhaust produced in the next generation nuclear processes in commercial applications such as nuclear hydrogen production is the trace level of tritium present in the exhaust gas streams. This presents a significant challenge since the removal of tritium from the high temperature gas stream must be accomplished at elevated temperatures in order to subsequently make use of this heat in downstream processing. One aspect of the current project is to extend the techniques and knowledge base for metal hydride materials being developed for the ''hydrogen economy'' based on low temperature absorption/desorption of hydrogen to develop materials with adequate thermal stability and an affinity for hydrogen at elevated temperatures. The second focus area of this project is to evaluate high temperature proton conducting materials as hydrogen isotope separation membranes. Both computational and experimental approaches will be applied to enhance the knowledge base of hydrogen interactions with metal and metal oxide materials. The common theme between both branches of research is the emphasis on both composition and microstructure influence on the performance of sequestration materials.

  16. Prediction of the temperature dependency of Henry's law constant using poly-parameter linear free energy relationships.

    Science.gov (United States)

    Goss, Kai-Uwe

    2006-08-01

    The ability to predict the temperature dependence of air/water partitioning is important for the environmental fate modeling of organic pollutants. Here, literature data for the temperature dependence of air/water partitioning of some 200 compounds have been used to derive poly-parameter linear free energy relationships (pp-LFER) for predicting air/water partition coefficients at temperatures between 0 and 45 degrees C. The compounds used for calibrating the pp-LFERs span a range of almost 10 orders of magnitude in the partition constants and they cover a large variety of functional groups. Very good fits (r(2)>0.99) were obtained at all temperatures. Hence, these pp-LFERs should serve as a valuable tool for integrating the temperature dependence of air/water partitioning into fate modeling of organic compounds. In the environment one will quite often encounter a situation where water and air do not have the same temperatures. This situation is shortly discussed in the appendix.

  17. An Approach for the Visualization of Temperature Distribution in Tissues According to Changes in Ultrasonic Backscattered Energy

    Directory of Open Access Journals (Sweden)

    Jingjing Xia

    2013-01-01

    Full Text Available Previous studies developed ultrasound temperature-imaging methods based on changes in backscattered energy (CBE to monitor variations in temperature during hyperthermia. In conventional CBE imaging, tracking and compensation of the echo shift due to temperature increase need to be done. Moreover, the CBE image does not enable visualization of the temperature distribution in tissues during nonuniform heating, which limits its clinical application in guidance of tissue ablation treatment. In this study, we investigated a CBE imaging method based on the sliding window technique and the polynomial approximation of the integrated CBE (ICBEpa image to overcome the difficulties of conventional CBE imaging. We conducted experiments with tissue samples of pork tenderloin ablated by microwave irradiation to validate the feasibility of the proposed method. During ablation, the raw backscattered signals were acquired using an ultrasound scanner for B-mode and ICBEpa imaging. The experimental results showed that the proposed ICBEpa image can visualize the temperature distribution in a tissue with a very good contrast. Moreover, tracking and compensation of the echo shift were not necessary when using the ICBEpa image to visualize the temperature profile. The experimental findings suggested that the ICBEpa image, a new CBE imaging method, has a great potential in CBE-based imaging of hyperthermia and other thermal therapies.

  18. The influence of temperature induced phase transition on the energy storage density of anti-ferroelectric ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Yi, Jinqiao; Zhang, Ling; Xie, Bing; Jiang, Shenglin, E-mail: nanx1013@163.com [School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2015-09-28

    Anti-ferroelectric (AFE) composite ceramics of (Pb{sub 0.858}Ba{sub 0.1}La{sub 0.02}Y{sub 0.008})(Zr{sub 0.65}Sn{sub 0.3}Ti{sub 0.05})O{sub 3}-(Pb{sub 0.97}La{sub 0.02})(Zr{sub 0.9}Sn{sub 0.05} Ti{sub 0.05})O{sub 3} (PBLYZST-PLZST) were fabricated by the conventional solid-state sintering process (CS), the glass-aided sintering (GAS), and the spark plasma sintering (SPS), respectively. The influence of the temperature induced phase transition on the phase structure, hysteresis loops, and energy storage properties of the composite ceramics were investigated in detail. The measured results of X-ray diffraction demonstrate that the composite ceramics exhibit the perovskite phases and small amounts of non-functional pyrochlore phases. Compared with the CS process, the GAS and SPS processes are proven more helpful to suppress the diffusion behaviors between the PBLYZST and PLZST phases according to the field emission scanning electron microscopy, thereby being able to improve the contribution of PBLYZST phase to the temperature stability of the orthogonal AFE phase. When the ambient temperature rises from 25 °C to 125 °C, CS and GAS samples have undergone a phase transition from orthorhombic AFE phase to tetragonal AFE phase, which results in a sharp decline in the energy storage density. However, the phase transition temperature of SPS samples is higher than 125 °C, and the energy storage density only slightly decreases due to the disorder of material microstructure caused by the high temperature. As a result, the SPS composite ceramics obtain a recoverable high energy storage density of 6.46 J/cm{sup 3} and the excellent temperature stability of the energy storage density of 1.16 × 10{sup −2} J/°C·cm{sup 3}, which is 1.29 × 10{sup −2} J/°C·cm{sup 3} lower than that of CS samples and about 0.43 times as that of GAS samples.

  19. Latent Heat Flux Estimate Through an Energy Water Balance Model and Land Surface Temperature from Remote Sensing

    Science.gov (United States)

    Corbari, Chiara; Sobrino, Jose A.; Mancini, Marco; Hidalgo, Victoria

    2011-01-01

    Soil moisture plays a key role in the terrestrial water cycle and is responsible for the partitioning of precipitation between runoff and infiltration. Moreover, surface soil moisture controls the redistribution of the incoming solar radiation on land surface into sensible and latent heat fluxes. Recent developments have been made to improve soil moisture dynamics predictions with hydrologic land surface models (LSMs) that compute water and energy balances between the land surface and the low atmosphere. However, most of the time soil moisture is confined to an internal numerical model variable mainly due to its intrinsic space and time variability and to the well known difficulties in assessing its value from remote sensing as from in situ measurements. In order to exploit the synergy between hydrological distributed models and thermal remote sensed data, FEST-EWB, a land surface model that solves the energy balance equation, was developed. In this hydrological model, the energy budget is solved looking for the representative thermodynamic equilibrium temperature (RET) defined as the land surface temperature that closes the energy balance equation. So using this approach, soil moisture is linked to the latent heat flux and then to LST. In this work the relationship between land surface temperature and soil moisture is analysed using LST from AHS (airborne hyperspectral scanner), with a spatial resolution of 2-4 m, LST from MODIS, with a spatial resolution of 1000 m, and thermal infrared radiometric ground measurements that are compared with the thermodynamic equilibrium temperature from the energy water balance model. Moreover soil moisture measurements were carried out during the airborne overpasses and then compared with SM from the hydrological model. An improvement of this well known inverse relationship between soil moisture and land surface temperature is obtained when the thermodynamic approach is used. The analysis of the scale effects of the different

  20. Synchronous temperature rate control and apparatus for refrigeration with reduced energy consumption

    Science.gov (United States)

    Gomes, Alberto Regio; Keres, Stephen L.; Kuehl, Steven J.; Litch, Andrew D.; Richmond, Peter J.; Wu, Guolian

    2015-09-22

    A refrigerator appliance configuration, and associated methods of operation, for an appliance with a controller, a condenser, at least one evaporator, a compressor, and two refrigeration compartments. The configuration may be equipped with a variable-speed or variable-capacity compressor, variable speed evaporator or compartment fans, a damper, and/or a dual-temperature evaporator with a valve system to control flow of refrigerant through one or more pressure reduction devices. The controller, by operation of the compressor, fans, damper and/or valve system, depending on the appliance configuration, synchronizes alternating cycles of cooling each compartment to a temperature approximately equal to the compartment set point temperature.

  1. Analysis of Thermal and Chemical Effets on Negative Valve Overlap Period Energy Recovery for Low-Temperature Gasoline Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Ekoto, Dr Isaac [Sandia National Laboratories (SNL); Peterson, Dr. Brian [University of Edinburgh; Szybist, James P [ORNL; Northrop, Dr. William [University of Minnesota

    2015-01-01

    A central challenge for efficient auto-ignition controlled low-temperature gasoline combustion (LTGC) engines has been achieving the combustion phasing needed to reach stable performance over a wide operating regime. The negative valve overlap (NVO) strategy has been explored as a way to improve combustion stability through a combination of charge heating and altered reactivity via a recompression stroke with a pilot fuel injection. The study objective was to analyze the thermal and chemical effects on NVO-period energy recovery. The analysis leveraged experimental gas sampling results obtained from a single-cylinder LTGC engine along with cylinder pressure measurements and custom data reduction methods used to estimate period thermodynamic properties. The engine was fueled by either iso-octane or ethanol, and operated under sweeps of NVO-period oxygen concentration, injection timing, and fueling rate. Gas sampling at the end of the NVO period was performed via a custom dump-valve apparatus, with detailed sample speciation by in-house gas chromatography. The balance of NVO-period input and output energy flows was calculated in terms of fuel energy, work, heat loss, and change in sensible energy. Experiment results were complemented by detailed chemistry single-zone reactor simulations performed at relevant mixing and thermodynamic conditions, with results used to evaluate ignition behavior and expected energy recovery yields. For the intermediate bulk-gas temperatures present during the NVO period (900-1100 K), weak negative temperature coefficient behavior with iso-octane fueling significantly lengthened ignition delays relative to similar ethanol fueled conditions. Faster ethanol ignition chemistry led to lower recovered fuel intermediate yields relative to similar iso-octane fueled conditions due to more complete fuel oxidation. From the energy analysis it was found that increased NVO-period global equivalence ratio, either from lower NVOperiod oxygen

  2. Experimental investigations of the minimum ignition energy and the minimum ignition temperature of inert and combustible dust cloud mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Addai, Emmanuel Kwasi, E-mail: emmanueladdai41@yahoo.com; Gabel, Dieter; Krause, Ulrich

    2016-04-15

    Highlights: • Ignition sensitivity of a highly flammable dust decreases upon addition of inert dust. • Minimum ignition temperature of a highly flammable dust increases when inert concentration increase. • Minimum ignition energy of a highly flammable dust increases when inert concentration increase. • The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%. - Abstract: The risks associated with dust explosions still exist in industries that either process or handle combustible dust. This explosion risk could be prevented or mitigated by applying the principle of inherent safety (moderation). This is achieved by adding an inert material to a highly combustible material in order to decrease the ignition sensitivity of the combustible dust. The presented paper deals with the experimental investigation of the influence of adding an inert dust on the minimum ignition energy and the minimum ignition temperature of the combustible/inert dust mixtures. The experimental investigation was done in two laboratory scale equipment: the Hartmann apparatus and the Godbert-Greenwald furnace for the minimum ignition energy and the minimum ignition temperature test respectively. This was achieved by mixing various amounts of three inert materials (magnesium oxide, ammonium sulphate and sand) and six combustible dusts (brown coal, lycopodium, toner, niacin, corn starch and high density polyethylene). Generally, increasing the inert materials concentration increases the minimum ignition energy as well as the minimum ignition temperatures until a threshold is reached where no ignition was obtained. The permissible range for the inert mixture to minimize the ignition risk lies between 60 to 80%.

  3. Kinetic modeling of ultrasound-assisted extraction of phenolic compounds from grape marc: influence of acoustic energy density and temperature.

    Science.gov (United States)

    Tao, Yang; Zhang, Zhihang; Sun, Da-Wen

    2014-07-01

    The effects of acoustic energy density (6.8-47.4 W/L) and temperature (20-50 °C) on the extraction yields of total phenolics and tartaric esters during ultrasound-assisted extraction from grape marc were investigated in this study. The ultrasound treatment was performed in a 25-kHz ultrasound bath system and the 50% aqueous ethanol was used as the solvent. The initial extraction rate and final extraction yield increased with the increase of acoustic energy density and temperature. The two site kinetic model was used to simulate the kinetics of extraction process and the diffusion model based on the Fick's second law was employed to determine the effective diffusion coefficient of phenolics in grape marc. Both models gave satisfactory quality of data fit. The diffusion process was divided into one fast stage and one slow stage and the diffusion coefficients in both stages were calculated. Within the current experimental range, the diffusion coefficients of total phenolics and tartaric esters for both diffusion stages increased with acoustic energy density. Meanwhile, the rise of temperature also resulted in the increase of diffusion coefficients of phenolics except the diffusion coefficient of total phenolics in the fast stage, the value of which being the highest at 40 °C. Moreover, an empirical equation was suggested to correlate the effective diffusion coefficient of phenolics in grape marc with acoustic energy density and temperature. In addition, the performance comparison of ultrasound-assisted extraction and convention methods demonstrates that ultrasound is an effective and promising technology to extract bioactive substances from grape marc. Copyright © 2014 Elsevier B.V. All rights reserved.

  4. High Temperature Superconducting Levitation Energy Storage Flywheel having Stable Levitation without Control and Its Vibration Control Electromagnetic Damper

    OpenAIRE

    福室, 允央; 大関, 健一郎; 斎藤, 正人; 葛, 徳梁; 村上, 岩範; 長屋, 幸助

    2004-01-01

    A simple and stable energy-storage flywheel system with high temperature superconducting levitation is presented. In order to have stable levitation, a superconductor and a permanent magnet are used, and 3 permanent magnets support the top of the shaft. In the part of drive system, 8-poles permanent magnet and 8 coils are used to cancel electromagnetic forces in the radial direction. An electromagnetic damper consisting of permanent magnet for levitation and 4 coils is presented which lies at...

  5. Preliminary Performance Evaluation of MEMS-based Piezoelectric Energy Harvesters in Extended Temperature Range

    DEFF Research Database (Denmark)

    Xu, R.; Borregaard, L.M.; Lei, A.

    2012-01-01

    In this work a batch of MEMS-based vibration energy harvesters consisting of a silicon/PZT thick film ntilever with integrated proof mass is characterized. The purpose of a vibration energy harvester is to convert low grade vibrations to useful electrical power. Optimally, the natural frequency o...

  6. An integrated model of soil-canopy spectral radiances, photosynthesis, fluorescence, temperature and energy balance

    NARCIS (Netherlands)

    Tol, van der C.; Verhoef, W.; Timmermans, J.; Verhoef, A.; Su, Z.

    2009-01-01

    This paper presents the model SCOPE (Soil Canopy Observation, Photochemistry and Energy fluxes), which is a vertical (1-D) integrated radiative transfer and energy balance model. The model links visible to thermal infrared radiance spectra (0.4 to 50 µm) as observed above the canopy to the fluxes of

  7. Temperature-time dependent transmittance, sheet resistance and bonding energy of reduced graphene oxide on soda lime glass

    Science.gov (United States)

    Kumar, Raj; Kumar, R. Manoj; Bera, Parthasarathi; Ariharan, S.; Lahiri, Debrupa; Lahiri, Indranil

    2017-12-01

    Reduced graphene oxide coated soda lime glass can act as an alternative transparent/conducting electrode for many opto-electronic applications. However, bonding between the deposited reduced graphene oxide film and the glass substrate is important for achieving better stability of the coating and an extended device lifetime. In the present study, delamination energy of reduced graphene oxide on soda lime glass was quantified by using nanoscratch technique. Graphene oxide was deposited on soda lime glass by dip coating technique and was thermally reduced at different temperatures (100 °C, 200 °C, 300 °C, 400 °C and 500 °C) and treatment time (2 h, 3 h, 4 h, 5 h and 10 h) in Ar (95%) with H2 (5%) atmosphere. An inverse behavior of delamination energy with temperature and treatment time was observed, which could be correlated with the removal of oxygen functional groups. Sheet resistance of the film demonstrated a steady decay with increasing temperature and treatment time. Functional groups attached to the graphene planes have more influence on conductivity than groups attached to the edges. Removal of functional groups could also be related to optical transmittance of the samples. Knowledge generated in this study with respect to delamination energy, sheet resistance and optical transmittance could be extensively used for various opto-electronic applications.

  8. Novel Modified Optical Fibers for High Temperature In-Situ Miniaturized Gas Sensors in Advanced Fossil Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Pickrell, Gary [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States); Scott, Brian [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States)

    2014-06-30

    This report covers the technical progress on the program “Novel Modified Optical Fibers for High Temperature In-Situ Miniaturized Gas Sensors in Advanced Fossil Energy Systems”, funded by the National Energy Technology Laboratory of the U.S. Department of Energy, and performed by the Materials Science & Engineering and Electrical & Computer Engineering Departments at Virginia Tech, and summarizes technical progress from July 1st, 2005 –June 30th, 2014. The objective of this program was to develop novel fiber materials for high temperature gas sensors based on evanescent wave absorption in optical fibers. This project focused on two primary areas: the study of a sapphire photonic crystal fiber (SPCF) for operation at high temperature and long wavelengths, and a porous glass based fiber optic sensor for gas detection. The sapphire component of the project focused on the development of a sapphire photonic crystal fiber, modeling of the new structures, fabrication of the optimal structure, development of a long wavelength interrogation system, testing of the optical properties, and gas and temperature testing of the final sensor. The fabrication of the 6 rod SPCF gap bundle (diameter of 70μm) with a hollow core was successfully constructed with lead-in and lead-out 50μm diameter fiber along with transmission and gas detection testing. Testing of the sapphire photonic crystal fiber sensor capabilities with the developed long wavelength optical system showed the ability to detect CO2 at or below 1000ppm at temperatures up to 1000°C. Work on the porous glass sensor focused on the development of a porous clad solid core optical fiber, a hollow core waveguide, gas detection capabilities at room and high temperature, simultaneous gas species detection, suitable joining technologies for the lead-in and lead-out fibers and the porous sensor, sensor system sensitivity improvement, signal processing improvement, relationship between pore structure and fiber

  9. The Quaternary groundwater as the low temperature energy source for heat pumps in Małopolska Province

    Science.gov (United States)

    Kmiecik, Ewa; Tomaszewska, Barbara; Mazurkiewicz, Justyna

    2017-11-01

    The paper presents the assessment of using Quaternary groundwater as the low-temperature energy source for heat pumps in the Małopolska Province. The analysis demonstrates that the Małopolska region has potential to use Quaternary groundwater in low-temperature systems both in terms of potential well flow rates and water temperature. Water as a heat source must also meet the relevant requirements in terms of the physical and chemical parameters indicated by manufacturers of heat pumps as important for the proper operation of installations. The data for this study were obtained from the Polish Hydrogeological Survey (the PHS is carried out by the Polish Geological Institute — National Research Institute). In some cases, physical and chemical properties of water do not meet the requirements indicated by heat pump manufacturers. These requirements may be met by using recycled water or another medium whose parameters do not affect the life of the installation.

  10. Ground Thermal Diffusivity Calculation by Direct Soil Temperature Measurement. Application to very Low Enthalpy Geothermal Energy Systems.

    Science.gov (United States)

    Andújar Márquez, José Manuel; Martínez Bohórquez, Miguel Ángel; Gómez Melgar, Sergio

    2016-02-29

    This paper presents a methodology and instrumentation system for the indirect measurement of the thermal diffusivity of a soil at a given depth from measuring its temperature at that depth. The development has been carried out considering its application to the design and sizing of very low enthalpy geothermal energy (VLEGE) systems, but it can has many other applications, for example in construction, agriculture or biology. The methodology is simple and inexpensive because it can take advantage of the prescriptive geotechnical drilling prior to the construction of a house or building, to take at the same time temperature measurements that will allow get the actual temperature and ground thermal diffusivity to the depth of interest. The methodology and developed system have been tested and used in the design of a VLEGE facility for a chalet with basement at the outskirts of Huelva (a city in the southwest of Spain). Experimental results validate the proposed approach.

  11. Ground Thermal Diffusivity Calculation by Direct Soil Temperature Measurement. Application to very Low Enthalpy Geothermal Energy Systems

    Directory of Open Access Journals (Sweden)

    José Manuel Andújar Márquez

    2016-02-01

    Full Text Available This paper presents a methodology and instrumentation system for the indirect measurement of the thermal diffusivity of a soil at a given depth from measuring its temperature at that depth. The development has been carried out considering its application to the design and sizing of very low enthalpy geothermal energy (VLEGE systems, but it can has many other applications, for example in construction, agriculture or biology. The methodology is simple and inexpensive because it can take advantage of the prescriptive geotechnical drilling prior to the construction of a house or building, to take at the same time temperature measurements that will allow get the actual temperature and ground thermal diffusivity to the depth of interest. The methodology and developed system have been tested and used in the design of a VLEGE facility for a chalet with basement at the outskirts of Huelva (a city in the southwest of Spain. Experimental results validate the proposed approach.

  12. Influence of fermentation temperature on the content of fatty acids in low energy milk-based kombucha products

    Directory of Open Access Journals (Sweden)

    Malbaša Radomir V.

    2011-01-01

    Full Text Available The aim of this study was to investigate the influence of fermentation temperature on the fatty acids content in low energy milk-based products obtained by kombucha inoculums with herbal teas. In this investigation low energy milk-based kombucha products were produced from milk with 0.8% milk fat using 10% (v/v kombucha inoculums cultivated on winter savory, peppermint, stinging nettle and wild thyme. The process of fermentation was conducted at two temperatures: 40°C and 43°C. Fermentation was stopped after the pH value of 4.5 was reached. Duration of the fermentation process was shorter by applying higher fermentation temperature. Fatty acids content was determined by gas chromatography-mass spectrometry. Predominant fatty acids in all obtained products were saturated fatty acids, first of all the monounsaturated ones. The higher temperature resulted in the formation of lower amount of saturated fatty acids in the obtained milk-based kombucha products.

  13. Accurate electronic free energies of the 3 d ,4 d , and 5 d transition metals at high temperatures

    Science.gov (United States)

    Zhang, Xi; Grabowski, Blazej; Körmann, Fritz; Freysoldt, Christoph; Neugebauer, Jörg

    2017-04-01

    Free energies of bulk materials are nowadays routinely computed by density functional theory. In particular for metals, electronic excitations can significantly contribute to the free energy. For an ideal static lattice, this contribution can be obtained at low computational cost, e.g., from the electronic density of states derived at T =0 K or by utilizing the Sommerfeld approximation. The error introduced by these approximations at elevated temperatures is rarely known. The error arising from the ideal lattice approximation is likewise unexplored but computationally much more challenging to overcome. In order to shed light on these issues we have computed the electronic free energies for all 3 d ,4 d , and 5 d transition elements on the ideal lattices of the bcc, fcc, and hcp structures using finite-temperature density-functional theory. For a subset of elements we have explored the impact of explicit thermal vibrations on the electronic free energies by using ab initio molecular dynamics simulations. We provide an analysis of the observed chemical trends in terms of the electronic density of states and the canonical d band model and quantify the errors in the approximate methods. The electronic contribution to the heat capacities and the corresponding errors due to the different approximations are studied as well.

  14. Limits to sustained energy intake XXIV: impact of suckling behaviour on the body temperatures of lactating female mice

    Science.gov (United States)

    Gamo, Y.; Bernard, A.; Troup, C.; Munro, F.; Derrer, K.; Jeannesson, N.; Campbell, A.; Gray, H.; Miller, J.; Dixon, J.; Mitchell, S. E.; Hambly, C.; Vaanholt, L. M.; Speakman, J. R.

    2016-01-01

    The objective of this study was to investigate the potential causes of high body temperature (Tb) during lactation in mice as a putative limit on energy intake. In particular we explored whether or not offspring contributed to heat retention in mothers while suckling. Tb and physical activity were monitored in 26 female MF1 mice using intraperitoneally implanted transmitters. In addition, maternal behaviour was scored each minute for 8 h d−1 throughout lactation. Mothers that raised larger litters tended to have higher Tb while nursing inside nests (P lactation was correlated with daily increases in energy intake. Chronic hyperthermia during lactation was not caused by increased heat retention due to surrounding offspring. Other factors, like metabolic heat produced as a by-product of milk production or energy intake may be more important factors. Heat dissipation limits are probably not a phenomenon restricted to lactation. PMID:27157478

  15. LARGE-SCALE HYDROGEN PRODUCTION FROM NUCLEAR ENERGY USING HIGH TEMPERATURE ELECTROLYSIS

    Energy Technology Data Exchange (ETDEWEB)

    James E. O' Brien

    2010-08-01

    Hydrogen can be produced from water splitting with relatively high efficiency using high-temperature electrolysis. This technology makes use of solid-oxide cells, running in the electrolysis mode to produce hydrogen from steam, while consuming electricity and high-temperature process heat. When coupled to an advanced high temperature nuclear reactor, the overall thermal-to-hydrogen efficiency for high-temperature electrolysis can be as high as 50%, which is about double the overall efficiency of conventional low-temperature electrolysis. Current large-scale hydrogen production is based almost exclusively on steam reforming of methane, a method that consumes a precious fossil fuel while emitting carbon dioxide to the atmosphere. Demand for hydrogen is increasing rapidly for refining of increasingly low-grade petroleum resources, such as the Athabasca oil sands and for ammonia-based fertilizer production. Large quantities of hydrogen are also required for carbon-efficient conversion of biomass to liquid fuels. With supplemental nuclear hydrogen, almost all of the carbon in the biomass can be converted to liquid fuels in a nearly carbon-neutral fashion. Ultimately, hydrogen may be employed as a direct transportation fuel in a “hydrogen economy.” The large quantity of hydrogen that would be required for this concept should be produced without consuming fossil fuels or emitting greenhouse gases. An overview of the high-temperature electrolysis technology will be presented, including basic theory, modeling, and experimental activities. Modeling activities include both computational fluid dynamics and large-scale systems analysis. We have also demonstrated high-temperature electrolysis in our laboratory at the 15 kW scale, achieving a hydrogen production rate in excess of 5500 L/hr.

  16. High Energy Density Li-ion Batteries Designed for Low Temperature Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NEI Corporation proposes to develop a mixed metal oxide nanocomposite cathode that is designed for delivering high energy density with good rate performance at low...

  17. High Energy Density Li-Ion Batteries Designed for Low Temperature Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The state-of-the-art Li-ion batteries do not fully meet the energy density, power density and safety requirements specified by NASA for future exploration missions....

  18. Vibrational energy relaxation of a diatomic molecule in a room-temperature ionic liquid.

    Science.gov (United States)

    Shim, Youngseon; Kim, Hyung J

    2006-07-14

    Vibrational energy relaxation (VER) dynamics of a diatomic solute in ionic liquid 1-ethyl-3-methylimidazolium hexafluorophosphate (EMI(+)PF(6) (-)) are studied via equilibrium and nonequilibrium molecular dynamics simulations. The time scale for VER is found to decrease markedly with the increasing solute dipole moment, consonant with many previous studies in polar solvents. A detailed analysis of nonequilibrium results shows that for a dipolar solute, dissipation of an excess solute vibrational energy occurs almost exclusively via the Lennard-Jones interactions between the solute and solvent, while an oscillatory energy exchange between the two is mainly controlled by their electrostatic interactions. Regardless of the anharmonicity of the solute vibrational potential, VER becomes accelerated as the initial vibrational energy increases. This is attributed primarily to the enhancement in variations of the solvent force on the solute bond, induced by large-amplitude solute vibrations. One interesting finding is that if a time variable scaled with the initial excitation energy is employed, dissipation dynamics of the excess vibrational energy of the dipolar solute tend to show a universal behavior irrespective of its initial vibrational state. Comparison with water and acetonitrile shows that overall characteristics of VER in EMI(+)PF(6) (-) are similar to those in acetonitrile, while relaxation in water is much faster than the two. It is also found that the Landau-Teller theory predictions for VER time scale obtained via equilibrium simulations of the solvent force autocorrelation function are in reasonable agreement with the nonequilibrium results.

  19. ALD grown nanostructured ZnO thin films: Effect of substrate temperature on thickness and energy band gap

    Directory of Open Access Journals (Sweden)

    Javed Iqbal

    2016-10-01

    Full Text Available Nanostructured ZnO thin films with high transparency have been grown on glass substrate by atomic layer deposition at various temperatures ranging from 100 °C to 300 °C. Efforts have been made to observe the effect of substrate temperature on the thickness of the deposited thin films and its consequences on the energy band gap. A remarkably high growth rate of 0.56 nm per cycle at a substrate temperature of 200 °C for ZnO thin films have been achieved. This is the maximum growth rate for ALD deposited ZnO thin films ever reported so far to the best of our knowledge. The studies of field emission scanning electron microscopy and X-ray diffractometry patterns confirm the deposition of uniform and high quality nanosturtured ZnO thin films which have a polycrystalline nature with preferential orientation along (100 plane. The thickness of the films deposited at different substrate temperatures was measured by ellipsometry and surface profiling system while the UV–visible and photoluminescence spectroscopy studies have been used to evaluate the optical properties of the respective thin films. It has been observed that the thickness of the thin film depends on the substrate temperatures which ultimately affect the optical and structural parameters of the thin films.

  20. Analytical Investigation of the Significance of Turbine-Inlet Temperature in High-Energy Rocket Turbodrive Applications

    Science.gov (United States)

    Rohlik, Harold E.

    1959-01-01

    The effect of turbine-inlet temperature on rocket gross weight was investigated for three high-energy long-range rockets in order to explore the desirability of turbine cooling in rocket turbodrive applications. Temperatures above and below the maximum that is permissible in uncooled turbines were included. Turbine bleed rate and stage number were considered as independent variables. The gross weight of the hydrogen-reactor system was more sensitive to changes in turbine-inlet temperature than either the hydrogen-oxygen or the hydrogen-fluorine systems. Gross weight of the hydrogen-reactor system could be reduced by 2.6 percent by the use of cooling and a turbine-inlet temperature of 3000 R. The reductions in the first stages of the hydrogen-oxygen and hydrogen-fluorine systems were 0.7 and 0.2 percent, respectively. The effect of turbine-inlet temperature on rocket gross weight was small because the resulting turbine weight and bleed rate variations were small. Since these small gains must be balanced against considerations of greater cost, weight, and complexity as well as lessened reliability with a system utilizing a cooled turbine, none of the systems investigated showed gains warranting the use of turbine cooling.

  1. Flexible Dielectric Nanocomposites with Ultrawide Zero-Temperature Coefficient Windows for Electrical Energy Storage and Conversion under Extreme Conditions.

    Science.gov (United States)

    Shehzad, Khurram; Xu, Yang; Gao, Chao; Li, Hanying; Dang, Zhi-Min; Hasan, Tawfique; Luo, Jack; Duan, Xiangfeng

    2017-03-01

    Polymer dielectrics offer key advantages over their ceramic counterparts such as flexibility, scalability, low cost, and high breakdown voltages. However, a major drawback that limits more widespread application of polymer dielectrics is their temperature-dependent dielectric properties. Achieving dielectric constants with low/zero-temperature coefficient (L/0TC) over a broad temperature range is essential for applications in diverse technologies. Here, we report a hybrid filler strategy to produce polymer composites with an ultrawide L/0TC window of dielectric constant, as well as a significantly enhanced dielectric value, maximum energy storage density, thermal conductivity, and stability. By creating a series of percolative polymer composites, we demonstrated hybrid carbon filler based composites can exhibit a zero-temperature coefficient window of 200 °C (from -50 to 150 °C), the widest 0TC window for all polymer composite dielectrics reported to date. We further show the electric and dielectric temperature coefficient of the composites is highly stable against stretching and bending, even under AC electric field with frequency up to 1 MHz. We envision that our method will push the functional limits of polymer dielectrics for flexible electronics in extreme conditions such as in hybrid vehicles, aerospace, power electronics, and oil/gas exploration.

  2. High-Temperature Motor Windings for Downhole Pumps Used in Geothermal Energy Production

    Energy Technology Data Exchange (ETDEWEB)

    Hooker, Matthew; Hazelton, Craig; Kano, Kimi

    2010-12-31

    The development of highly reliable downhole equipment is an essential element in enabling the widespread utilization of Enhanced Geothermal Systems (EGS). The downhole equipment used in these systems will be required to operate at high voltages and temperatures on the order of 200 to 250°C (and eventually to 300°C). These conditions exceed the practical operating ranges of currently available thermoplastic wire insulations, and thus limit the operating lifetime of tools such as Electric Submersible Pumps (ESPs). In this work, high-temperature insulations based on composite materials were developed and demonstrated. The products of this work were found to exhibit electrical resistivities and dielectric breakdown strengths that PEEK at temperatures above 250C. In addition, sub-scale motor windings were fabricated and tested to validate the performance of this technology

  3. Evolution of snow and ice temperature, thickness and energy balance in Lake Orajärvi, northern Finland

    Directory of Open Access Journals (Sweden)

    Bin Cheng

    2014-05-01

    Full Text Available The seasonal evolution of snow and ice on Lake Orajärvi, northern Finland, was investigated for three consecutive winter seasons. Material consisting of numerical weather prediction model (HIRLAM output, weather station observations, manual snow and ice observations, high spatial resolution snow and ice temperatures from ice mass balance buoys (SIMB, and Moderate Resolution Imaging Spectroradiometer (MODIS lake ice surface temperature observations was gathered. A snow/ice model (HIGHTSI was applied to simulate the evolution of the snow and ice surface energy balance, temperature profiles and thickness. The weather conditions in early winter were found critical in determining the seasonal evolution of the thickness of lake ice and snow. During the winter season (Nov.–Apr., precipitation, longwave radiative flux and air temperature showed large inter-annual variations. The uncertainty in snow/ice model simulations originating from precipitation was investigated. The contribution of snow to ice transformation was vital for the total lake ice thickness. At the seasonal time scale, the ice bottom growth was 50–70% of the total ice growth. The SIMB is suitable for monitoring snow and ice temperatures and thicknesses. The Mean Bias Error (MBE between the SIMB and borehole measurements was −0.7 cm for snow thicknesses and 1.7 cm for ice thickness. The temporal evolution of MODIS surface temperature (three seasons agrees well with SIMB and HIGHTSI results (correlation coefficient, R=0.81. The HIGHTSI surface temperatures were, however, higher (2.8°C≤MBE≤3.9°C than the MODIS observations. The development of HIRLAM by increasing its horizontal and vertical resolution and including a lake parameterisation scheme improved the atmospheric forcing for HIGHTSI, especially the relative humidity and solar radiation. Challenges remain in accurate simulation of snowfall events and total precipitation.

  4. A simple temperature domain two-source model for estimating agricultural field surface energy fluxes from Landsat images

    Science.gov (United States)

    Yao, Yunjun; Liang, Shunlin; Yu, Jian; Chen, Jiquan; Liu, Shaomin; Lin, Yi; Fisher, Joshua B.; McVicar, Tim R.; Cheng, Jie; Jia, Kun; Zhang, Xiaotong; Xie, Xianhong; Jiang, Bo; Sun, Liang

    2017-05-01

    A simple and robust satellite-based method for estimating agricultural field to regional surface energy fluxes at a high spatial resolution is important for many applications. We developed a simple temperature domain two-source energy balance (TD-TSEB) model within a hybrid two-source model scheme by coupling "layer" and "patch" models to estimate surface heat fluxes from Landsat thematic mapper/Enhanced Thematic Mapper Plus (TM/ETM+) imagery. For estimating latent heat flux (LE) of full soil, we proposed a temperature domain residual of the energy balance equation based on a simplified framework of total aerodynamic resistances, which provides a key link between thermal satellite temperature and subsurface moisture status. Additionally, we used a modified Priestley-Taylor model for estimating LE of full vegetation. The proposed method was applied to TM/ETM+ imagery and was validated using the ground-measured data at five crop eddy-covariance tower sites in China. The results show that TD-TSEB yielded root-mean-square-error values between 24.9 (8.9) and 78.2 (21.4) W/m2 and squared correlation coefficient (R2) values between 0.60 (0.51) and 0.97 (0.90), for the estimated instantaneous (daily) surface net radiation, soil, latent, and sensible heat fluxes at all five sites. The TD-TSEB model shows good accuracy for partitioning LE into soil (LEsoil) and canopy (LEcanopy) components with an average bias of 11.1% for the estimated LEsoil/LE ratio at the Daman site. Importantly, the TD-TSEB model produced comparable accuracy but requires fewer forcing data (i.e., no wind speed and roughness length are needed) when compared with two other widely used surface energy balance models. Sensitivity analyses demonstrated that this accurate operational model provides an alternative method for mapping field surface heat fluxes with satisfactory performance.

  5. Workpiece temperature distribution for deep penetration welding with high energy focused beams

    Science.gov (United States)

    Peretz, R.

    1986-01-01

    A solution for the two-dimensional temperature field in a workpiece at welding by laser or electron beams, which takes into consideration the solid-to-liquid phase change of the material, is presented. This leads to more precise process parameter correlations.

  6. Development of Three-Tier Heat, Temperature and Internal Energy Diagnostic Test

    Science.gov (United States)

    Gurcay, Deniz; Gulbas, Etna

    2015-01-01

    Background: Misconceptions are major obstacles to learning physics, and the concepts of heat and temperature are some of the common misconceptions that are encountered in daily life. Therefore, it is important to develop valid and reliable tools to determine students' misconceptions about basic thermodynamics concepts. Three-tier tests are…

  7. Optimisation of CO2 and Temperature in Terms of Crop Growth and Energy Use

    NARCIS (Netherlands)

    Dieleman, J.A.; Meinen, E.; Marcelis, L.F.M.; Zwart, de H.F.; Henten, van E.J.

    2005-01-01

    In current greenhouse climate control, temperature set points follow a pre-set trajectory based on absolute or solar time parameters, adapted only to instantaneous and daily radiation. CO2 is supplied during a well defined period of the day until a maximum concentration is reached. However, the rate

  8. Determination of temperature and residual laser energy on film fiber-optic thermal converter for diode laser surgery.

    Science.gov (United States)

    Liu, Weichao; Kong, Yaqun; Shi, Xiafei; Dong, Xiaoxi; Wang, Hong; Zhao, Jizhi; Li, Yingxin

    2017-12-01

    The diode laser was utilized in soft tissue incision of oral surgery based on the photothermic effect. The contradiction between the ablation efficiency and the thermal damage has always been in diode laser surgery, due to low absorption of its radiation in the near infrared region by biological tissues. Fiber-optic thermal converters (FOTCs) were used to improve efficiency for diode laser surgery. The purpose of this study was to determine the photothermic effect by the temperature and residual laser energy on film FOTCs. The film FOTC was made by a distal end of optical fiber impacting on paper. The external surface of the converter is covered by a film contained amorphous carbon. The diode laser with 810 nm worked at the different rated power of 1.0 W, 1.5 W, 2.0 W, 3.0 W, 4.0 W, 5.0 W, 6.0 W, 7.0 W, 8.0 W in continuous wave (CW)and pulse mode. The temperature of the distal end of optical fiber was recorded and the power of the residual laser energy from the film FOTC was measured synchronously. The temperature, residual power and the output power were analyzed by linear or exponential regression model and Pearson correlations analysis. The residual power has good linearity versus output power in CW and pulse modes (R2 = 0.963, P < 0.01 for both). The temperature on film FOTCs increases exponentially with adjusted R2 = 0.959 in continuous wave mode, while in pulsed mode with adjusted R2 = 0.934. The temperature was elevated up to about 210 °C and eventually to be a stable state. Film FOTCs centralized approximately 50% of laser energy on the fiber tip both in CW and pulsed mode while limiting the ability of the laser light to interact directly with target tissue. Film FOTCs can concentrate part of laser energy transferred to heat on distal end of optical fiber, which have the feasibility of improving efficiency and reducing thermal damage of deep tissue.

  9. Effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain.

    Science.gov (United States)

    Li, Kai Chun; Waddell, J Neil; Prior, David J; Ting, Stephanie; Girvan, Liz; van Vuuren, Ludwig Jansen; Swain, Michael V

    2013-11-01

    To investigate the effect of autoclave induced low-temperature degradation on the adhesion energy between yttria-stabilized zirconia veneered with porcelain. The strain energy release rate using a four-point bending stable fracture test was evaluated for two different porcelains [leucite containing (VM9) and glass (Zirox) porcelain] veneered to zirconia. Prior to veneering the zirconia had been subjected to 0 (control), 1, 5, 10 and 20 autoclave cycles. The specimens were manufactured to a total bi-layer dimension of 30 mm × 8 mm × 3 mm. Subsequent scanning electron microscopy/energy dispersive spectrometry, electron backscatter diffraction and X-ray diffraction analysis were performed to identify the phase transformation and fracture behavior. The strain energy release rate for debonding of the VM9 specimens were significantly higher (pautoclave cycles lowered the strain energy release rate significantly (pautoclave cycles between 5 and 20. The monoclinic phase reverted back to tetragonal phase after undergoing conventional porcelain firing cycles. EBSD data showed significant changes of the grain size distribution between the control and autoclaved specimen (cycle 20). Increasing autoclave cycles only significantly decreased the adhesion of the VM9 layered specimens. In addition, a conventional porcelain firing schedule completely reverted the monoclinic phase back to tetragonal. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  10. Exposure to elevated temperature and Pco(2) reduces respiration rate and energy status in the periwinkle Littorina littorea.

    Science.gov (United States)

    Melatunan, Sedercor; Calosi, Piero; Rundle, Simon D; Moody, A John; Widdicombe, Stephen

    2011-01-01

    In the future, marine organisms will face the challenge of coping with multiple environmental changes associated with increased levels of atmospheric Pco(2), such as ocean warming and acidification. To predict how organisms may or may not meet these challenges, an in-depth understanding of the physiological and biochemical mechanisms underpinning organismal responses to climate change is needed. Here, we investigate the effects of elevated Pco(2) and temperature on the whole-organism and cellular physiology of the periwinkle Littorina littorea. Metabolic rates (measured as respiration rates), adenylate energy nucleotide concentrations and indexes, and end-product metabolite concentrations were measured. Compared with values for control conditions, snails decreased their respiration rate by 31% in response to elevated Pco(2) and by 15% in response to a combination of increased Pco(2) and temperature. Decreased respiration rates were associated with metabolic reduction and an increase in end-product metabolites in acidified treatments, indicating an increased reliance on anaerobic metabolism. There was also an interactive effect of elevated Pco(2) and temperature on total adenylate nucleotides, which was apparently compensated for by the maintenance of adenylate energy charge via AMP deaminase activity. Our findings suggest that marine intertidal organisms are likely to exhibit complex physiological responses to future environmental drivers, with likely negative effects on growth, population dynamics, and, ultimately, ecosystem processes.

  11. Correlation functions of the energy-momentum tensor in SU(2) gauge theory at finite temperature

    DEFF Research Database (Denmark)

    Huebner, K.; Karsch, F.; Pica, Claudio

    2008-01-01

    We calculate correlation functions of the energy-momentum tensor in the vicinity of the deconfinement phase transition of (3+1)-dimensional SU(2) gauge theory and discuss their critical behavior in the vicinity of the second order deconfinement transition. We show that correlation functions...... of the trace of the energy momentum tensor diverge uniformly at the critical point in proportion to the specific heat singularity. Correlation functions of the pressure, on the other hand, stay finite at the critical point. We discuss the consequences of these findings for the analysis of transport...

  12. Comparison of electron temperature fluctuations with gyrokinetic sumulations across the ohmic energy confinement transition in Alcator C-Mod

    Science.gov (United States)

    Sung, C.; White, A.; Howard, N.; Mikkelsen, D.; Rice, J.; Reinke, M.; Gao, C.; Ennever, P.; Porkolab, M.; Churchill, R.; Theiler, C.; Hubbard, A.; Greenwald, M.

    2013-10-01

    Long wavelength electron temperature fluctuations (kyρs < 0 . 3) near the edge (r / a ~ 0 . 85) are reduced across the ohmic confinement transition from Linear Ohmic Confinement(LOC) regime to Saturated Ohmic Confinement(SOC) regime in Alcator C-Mod. Linear stability analysis shows that the dominant mode of long wavelength turbulence near the edge is changed from Trapped Electron Mode(TEM) to Ion Temperature Gradient(ITG) mode while the dominant mode is not changed deeper in the core (r / a ~ 0 . 5). This indicates that local turbulence changes near the edge might be responsible for the change of global energy confinement in ohmic plasmas. Further study using nonlinear gyrokinetic simulations is being performed to clarify the relation between the change of local turbulence and global ohmic energy confinement. Through nonlinear gyrokinetic simulation (GYRO), we will investigate the change of fluctuating quantities (T~ , ñ , ϕ~) and their phase relations across ohmic confinement transitions, and relate them to the change of energy transport. A synthetic CECE diagnostic for C-Mod has been developed, and it will be used to validate the gyrokinetic simulations. Research supported by USDoE awards DE-SC0006419, DE-FC02-99ER54512.

  13. Energy

    CERN Document Server

    Graybill, George

    2007-01-01

    Unlock the mysteries of energy! Energy is more than ""the ability to do work""; we present these concepts in a way that makes them more accessible to students and easier to understand. The best way to understand energy is to first look at all the different kinds of energy including: What Is Energy, Mechanical Energy, Thermal, Sound Energy and Waves, as well as Light Energy.

  14. Potential energy savings using dynamically optimizing control in refrigeration systems under daily variations in ambient temperature

    DEFF Research Database (Denmark)

    Larsen, Lars Finn Sloth; Thybo, Claus; Wisniewski, Rafal

    2007-01-01

    The objective of this study is to investigate the energy saving potential for refrigeration systems by refrigeration more at the colder night time than at the warmer day time. The potential is evaluated using an optimal control policy and illustrated on a simulation example. The results show...

  15. Numerical investigation of temperature distribution and thermal performance while charging-discharging thermal energy in aquifer

    NARCIS (Netherlands)

    Ganguly, S.; Mohan Kumar, M.S.; Date, Abhijit; Akbarzadeh, Aliakbar

    2017-01-01

    A three-dimensional (3D) coupled thermo-hydrogeological numerical model for a confined aquifer thermal energy storage (ATES) system underlain and overlain by rock media has been presented in this paper. The ATES system operates in cyclic mode. The model takes into account heat transport processes of

  16. Synchronous compartment temperature control and apparatus for refrigeration with reduced energy consumption

    Science.gov (United States)

    Gomes, Alberto Regio; Keres, Stephen L.; Kuehl, Stephen J.; Litch, Andrew D.; Richmond, Peter J.; Wu, Guolian

    2015-09-22

    A refrigerator appliance configuration, and associated methods of operation, for an appliance with a controller, a condenser, at least one evaporator, a compressor, and two refrigeration compartments. The configuration may be equipped with a variable-speed or variable-capacity compressor, variable speed evaporator or compartment fans, a damper and/or a dual-temperature evaporator with a valve system to control flow of refrigerant through one or more pressure reduction devices. The controller, by operation of the compressor, fans, damper and/or valve system, depending on the appliance configuration, controls the cooling rate in one or both compartments to synchronize, alternating cycles of cooling the compartments to their set point temperatures.

  17. Efficiency of tandem solar cell systems as function of temperature and solar energy concentration ratio

    Science.gov (United States)

    Gokcen, N. A.; Loferski, J. J.

    1979-01-01

    The results of a comprehensive theoretical analysis of tandem photovoltaic solar cells as a function of temperature and solar concentration ratio are presented. The overall efficiencies of tandem cell stacks consisting of as many as 24 cells having gaps in the 0.7 to 3.6 eV range were calculated for temperatures of 200, 300, 400, and 500 K and for illumination by an AMO solar spectrum having concentration ratios of 1, 100, 500, and 1000 suns. For ideal diodes (A = B = 1), the calculations show that the optimized overall efficiency has a limiting value eta sub opt of approximately 70 percent for T = 200 K and C = 1000; for T = 300 K and C = 1000, this limiting efficiency approaches 60 percent.

  18. Low-Energy, Low-Cost Production of Ethylene by Low- Temperature Oxidative Coupling of Methane

    Energy Technology Data Exchange (ETDEWEB)

    Radaelli, Guido [Siluria Technologies, Inc., San Francisco, CA (United States); Chachra, Gaurav [Siluria Technologies, Inc., San Francisco, CA (United States); Jonnavittula, Divya [Siluria Technologies, Inc., San Francisco, CA (United States)

    2017-12-30

    In this project, we develop a catalytic process technology for distributed small-scale production of ethylene by oxidative coupling of methane at low temperatures using an advanced catalyst. The Low Temperature Oxidative Coupling of Methane (LT-OCM) catalyst system is enabled by a novel chemical catalyst and process pioneered by Siluria, at private expense, over the last six years. Herein, we develop the LT-OCM catalyst system for distributed small-scale production of ethylene by identifying and addressing necessary process schemes, unit operations and process parameters that limit the economic viability and mass penetration of this technology to manufacture ethylene at small-scales. The output of this program is process concepts for small-scale LT-OCM catalyst based ethylene production, lab-scale verification of the novel unit operations adopted in the proposed concept, and an analysis to validate the feasibility of the proposed concepts.

  19. Multi-Functional Current Multiplier by High Temperature Superconducting Magnet Energy Storage

    Science.gov (United States)

    Yamada, S.; Hishinuma, Y.; Aso, Y.

    We had been developing a current multiplier by inductive storage (CMIS). The prototype of CMIS consists of 12 storage copper coil with switching units. Coils and feeders are cooled by the liquid nitrogen to reduce the resistivity. Output current pulse with 480 A could be generated, by charging the coils to 40 A. The continuous current pulses of 666 pulses per minute were obtained owing to the fast switching of coil currents by using IGBTs. Two types of the multi-functional CMIS were designed conceptually; one is for mega ampere and the other is for long pulse. The system consists of the superconducting (SC) magnet section with a temperature of 20 K and the IGBT control switch section with a temperature of 77 K. The SC coil is cooled down from 77 to 20 K by a G-M refrigerator. The IGBT control switches are soaked in liquid nitrogen to reduce the total resistance from CMIS coils to the load.

  20. Development of heat exchanger for high temperature energy storage with bulk materials

    Science.gov (United States)

    Boura, Cristiano Teixeira; Niederwestberg, Stefan; McLeod, Jacqueline; Herrmann, Ulf; Hoffschmidt, Bernhard

    2016-05-01

    This paper gives a general overview of the concept of a high temperature gas-to-particle heat exchanger, the corresponding test facilities and the results of laboratory tests. A description of the optimal bulk material and separator properties and their influences on the operating conditions is also given. The three phenomena pinning, blistering and blocking could be observed during the tests and were analysed in more detail using simulation software.

  1. Elastocaloric effect on natural rubber and terpolymer : Temperature variation mechanism, morphology and energy balance during deformation

    OpenAIRE

    Yoshida 1988-...., Yukihiro

    2016-01-01

    Caloric effects (CEs), which are the phenomena that temperature variation is caused by entropy change, have been investigated for the novel system which might be able to replace conventional vapor compression refrigeration system. In the present thesis, the elastocaloric effect (ElCE) of natural rubber (NR) and terpolymer, poly(vinylidene fluoride-trifluoroethylene-chlorotrifluoroethylene) (P(VDF-TrFE-CTFE)), was focused. First of all, NR, which is an excellent candidate material for ElCE, wa...

  2. Coronal temperatures, heating, and energy flow in a polar region of the sun at solar maximum

    Science.gov (United States)

    Withbroe, G. L.; Kohl, J. L.; Weiser, H.; Munro, R. H.

    1985-01-01

    The profiles of resonantly scattered Lyman-alpha coronal radiation have been used to determine the hydrogen kinetic temperature from 1.5 to 4 solar radius from the center of the polar region of the corona observed in 1980 at solar maximum. Hydrogen temperatures derived from the line profiles were found to decrease with height from 1.2 million K at r = 1.5 solar radii to 600,000 K at r = 4 solar radius. Comparison of the measured kinetic temperatures with predictions from a semiempirical two-fluid model showed evidence of a small amount of heating or a nonthermal contribution to the motions of coronal protons between 1.5 and 4 solar radius. The widths of the profiles confirmed an upper limit of 110 + or - 15 km/s on the rms magnitude of the line-of-sight component of velocities between 1.5 and 4 solar radius. Density measurements obtained in situ in the solar wind in the ecliptic were used to locate the sources of low speed and high-speed winds in the polar region. An eclipse photograph of the corona at solar maximum is provided.

  3. Refined energy-conserving dissipative particle dynamics model with temperature-dependent properties and its application in solidification problem

    Science.gov (United States)

    Ng, K. C.; Sheu, T. W. H.

    2017-10-01

    It has been observed previously that the physical behaviors of Schmidt number (Sc) and Prandtl number (Pr) of an energy-conserving dissipative particle dynamics (eDPD) fluid can be reproduced by the temperature-dependent weight function appearing in the dissipative force term. In this paper, we proposed a simple and systematic method to develop the temperature-dependent weight function in order to better reproduce the physical fluid properties. The method was then used to study a variety of phase-change problems involving solidification. The concept of the "mushy" eDPD particle was introduced in order to better capture the temperature profile in the vicinity of the solid-liquid interface, particularly for the case involving high thermal conductivity ratio. Meanwhile, a way to implement the constant temperature boundary condition at the wall was presented. The numerical solutions of one- and two-dimensional solidification problems were then compared with the analytical solutions and/or experimental results and the agreements were promising.

  4. Changes in core electron temperature fluctuations across the ohmic energy confinement transition in Alcator C-Mod plasmas

    Science.gov (United States)

    Sung, C.; White, A. E.; Howard, N. T.; Oi, C. Y.; Rice, J. E.; Gao, C.; Ennever, P.; Porkolab, M.; Parra, F.; Mikkelsen, D.; Ernst, D.; Walk, J.; Hughes, J. W.; Irby, J.; Kasten, C.; Hubbard, A. E.; Greenwald, M. J.; the Alcator C-Mod Team

    2013-08-01

    The first measurements of long wavelength (kyρs < 0.3) electron temperature fluctuations in Alcator C-Mod made with a new correlation electron cyclotron emission diagnostic support a long-standing hypothesis regarding the confinement transition from linear ohmic confinement (LOC) to saturated ohmic confinement (SOC). Electron temperature fluctuations decrease significantly (∼40%) crossing from LOC to SOC, consistent with a change from trapped electron mode (TEM) turbulence domination to ion temperature gradient (ITG) turbulence as the density is increased. Linear stability analysis performed with the GYRO code (Candy and Waltz 2003 J. Comput. Phys. 186 545) shows that TEMs are dominant for long wavelength turbulence in the LOC regime and ITG modes are dominant in the SOC regime at the radial location (ρ ∼ 0.8) where the changes in electron temperature fluctuations are measured. In contrast, deeper in the core (ρ < 0.8), linear stability analysis indicates that ITG modes remain dominant across the LOC/SOC transition. This radial variation suggests that the robust global changes in confinement of energy and momentum occurring across the LOC/SOC transition are correlated to local changes in the dominant turbulent mode near the edge.

  5. Electron-Phonon Coupling and Energy Flow in a Simple Metal beyond the Two-Temperature Approximation

    Directory of Open Access Journals (Sweden)

    Lutz Waldecker

    2016-04-01

    Full Text Available The electron-phonon coupling and the corresponding energy exchange are investigated experimentally and by ab initio theory in nonequilibrium states of the free-electron metal aluminium. The temporal evolution of the atomic mean-squared displacement in laser-excited thin freestanding films is monitored by femtosecond electron diffraction. The electron-phonon coupling strength is obtained for a range of electronic and lattice temperatures from density functional theory molecular dynamics simulations. The electron-phonon coupling parameter extracted from the experimental data in the framework of a two-temperature model (TTM deviates significantly from the ab initio values. We introduce a nonthermal lattice model (NLM for describing nonthermal phonon distributions as a sum of thermal distributions of the three phonon branches. The contributions of individual phonon branches to the electron-phonon coupling are considered independently and found to be dominated by longitudinal acoustic phonons. Using all material parameters from first-principles calculations except the phonon-phonon coupling strength, the prediction of the energy transfer from electrons to phonons by the NLM is in excellent agreement with time-resolved diffraction data. Our results suggest that the TTM is insufficient for describing the microscopic energy flow even for simple metals like aluminium and that the determination of the electron-phonon coupling constant from time-resolved experiments by means of the TTM leads to incorrect values. In contrast, the NLM describing transient phonon populations by three parameters appears to be a sufficient model for quantitatively describing electron-lattice equilibration in aluminium. We discuss the general applicability of the NLM and provide a criterion for the suitability of the two-temperature approximation for other metals.

  6. Effects of the sintering temperature on the flux-pinning mechanism and the activation energy of malic-acid doped MgB2

    Directory of Open Access Journals (Sweden)

    J Peleckis

    2012-12-01

    Full Text Available   The flux-pinning mechanism and activation energy of 10 wt % malic acid-doped MgB2 were investigated by measuring of the critical current density and resistivity as a function of magnetic field and temperature. A crossover field, Bsb, was observed from the single vortex to the small vortex bundle pinning regime. For the sintered sample, the temperature dependence of Bsb(T at low temperature is in good agreement with the δℓ pinning mechanism, i.e., pinning associated with charge-carrier mean free path fluctuation. The activation energy was decreased by increasing the magnetic field and increased by increasing sintering temperature.

  7. Ambient temperature modulates the effects of the Prader-Willi syndrome candidate gene Snord116 on energy homeostasis.

    Science.gov (United States)

    Qi, Y; Purtell, L; Fu, M; Sengmany, K; Loh, K; Zhang, L; Zolotukhin, S; Sainsbury, A; Campbell, L; Herzog, H

    2017-02-01

    Germline deletion of the Prader-Willi syndrome (PWS) candidate gene Snord116 in mice leads to some classical symptoms of human PWS, notably reductions in body weight, linear growth and bone mass. However, Snord116 deficient mice (Snord116-/-) do not develop an obese phenotype despite their increased food intake and the underlying mechanism for that is unknown. We tested the phenotypes of germline Snord116-/- as well as neuropeptide Y (NPY) neuron specific Snord116lox/lox/NPYcre/+ mice at 30°C, the thermoneutral temperature of mice, and compared these to previous reports studies conducted at normal room temperature. Snord116-/- mice at 30°C still weighed less than wild type but had increased body weight gain. Importantly, food intake and energy expenditure were no longer different at 30°C, and the reduced bone mass and nasal-anal length observed in Snord116-/- mice at room temperature were also normalized. Mechanistically, the thermoneutral condition led to the correction of the mRNA expression of NPY and pro-opiomelanocortin (POMC), which were both previously observed to be significantly up-regulated at room temperature. Importantly, almost identical phenotypes and NPY/POMC mRNA expression alterations were also observed in Snord116lox/lox/NPYcre/+ mice, which lack the Snord116 gene only in NPY neurons. These data illustrate that mild cold stress is a critical factor preventing the development of obesity in Snord116-/- mice via the NPY system. Our study highlights that the function of Snord116 in the hypothalamus may be to enhance energy expenditure, likely via the NPY system, and also indicates that Snord116 function in mice is strongly dependent on environmental conditions such as cold exposure. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Effect of temperature on a free energy and equilibrium constants during dry flue gas desulphurisation chemical reactions

    Directory of Open Access Journals (Sweden)

    Kuburović Miloš

    2002-01-01

    Full Text Available During dry flue gas desulphurisation (FGD dry particles of reagents are inserted (injected in the stream of flue gas, where they bond SO2. As reagents, the most often are used compounds of calcium (CaCO3, CaO or Ca(OH2. Knowledge of free energy and equilibrium constants of chemical reactions during dry FGD is necessary for understanding of influence of flue gas temperature to course of these chemical reactions as well as to SO2 bonding from flue gases.

  9. Measurement of solid-liquid interfacial energy in the In-Bi eutectic alloy at low melting temperature

    Energy Technology Data Exchange (ETDEWEB)

    Marasli, N [Department of Physics, Faculty of Arts and Sciences, Erciyes University, 38039 Kayseri (Turkey); Akbulut, S [Institute of Science and Technology, Department of Physics, Erciyes University, 38039 Kayseri (Turkey); Ocak, Y [Department of Physics, Faculty of Arts and Sciences, Erciyes University, 38039 Kayseri (Turkey); Keslioglu, K [Department of Physics, Faculty of Arts and Sciences, Erciyes University, 38039 Kayseri (Turkey); Boeyuek, U [Institute of Science and Technology, Department of Physics, Erciyes University, 38039 Kayseri (Turkey); Kaya, H [Department of Science Education, Education Faculty, Erciyes University, 38039 Kayseri (Turkey); Cadirli, E [Department of Physics, Faculty of Arts and Sciences, Nigde University, Nigde (Turkey)

    2007-12-19

    The Gibbs-Thomson coefficient and solid-liquid interfacial energy of the solid In solution in equilibrium with In Bi eutectic liquid have been determined to be (1.46 {+-} 0.07) x 10{sup -7} K m and (40.4 {+-} 4.0) x 10{sup -3} J m{sup -2} by observing the equilibrated grain boundary groove shapes. The grain boundary energy of the solid In solution phase has been calculated to be (79.0 {+-} 8.7) x 10{sup -3} J m{sup -2} by considering force balance at the grain boundary grooves. The thermal conductivities of the In-12.4 at.% Bi eutectic liquid phase and the solid In solution phase and their ratio at the eutectic melting temperature (72 deg. C) have also been measured with radial heat flow apparatus and Bridgman-type growth apparatus.

  10. LMR core temperature calculation based on implicit formulation of the ENERGY model and a Krylov subspace method

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Won Sik [Chosun University, Department of Nuclear Engineering, Kwangju (Korea, Republic of); Joo, Han Gyu [Korea Atomic Energy Research Institute, Yusong, Taejon (Korea, Republic of)

    1999-05-01

    A computational method was developed for predicting the steady-state temperature field in an LMR core based on the simplified energy equation mixing model and the subchannel analysis method. The {theta}-method was employed for discretizing the energy equation in the axial direction, and the interassembly coupling was achieved by interassembly gap flow. For an implicit scheme, a Krylov subspace method based on the BiCGSTAB algorithm and the MILU preconditioning was employed to solve the resulting linear system at each axial level. Numerical test results suggest that at least an order of magnitude reduction in the computing time can be achieved with the implicit solution scheme employing the Krylov subspace method when compared to the explicit scheme.

  11. Determination of the electron energy distribution function of a low temperature plasma from optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Dodt, Dirk Hilar

    2009-01-05

    The experimental determination of the electron energy distribution of a low pressure glow discharge in neon from emission spectroscopic data has been demonstrated. The spectral data were obtained with a simple overview spectrometer and analyzed using a strict probabilistic, Bayesian data analysis. It is this Integrated Data Analysis (IDA) approach, which allows the significant extraction of non-thermal properties of the electron energy distribution function (EEDF). The results bear potential as a non-invasive alternative to probe measurements. This allows the investigation of spatially inhomogeneous plasmas (gradient length smaller than typical probe sheath dimensions) and plasmas with reactive constituents. The diagnostic of reactive plasmas is an important practical application, needed e.g. for the monitoring and control of process plasmas. Moreover, the experimental validation of probe theories for magnetized plasmas as a long-standing topic in plasma diagnostics could be addressed by the spectroscopic method. (orig.)

  12. High Temperature Latent Heat Thermal Energy Storage to Augment Solar Thermal Propulsion for Microsatellites

    Science.gov (United States)

    2015-08-30

    heat of fusion . In this work, boron is considered a long-term high performance solution and silicon is presented as a near term development target with... conceptual studies. However, there have been no thorough investigations due to the absence of existing research in addition to cost and schedule constraints...driven by a nuclear thermal energy source. Zubrin et al. proposed a “bi-modal” approach which modified an existing 40 kWe nuclear-thermionic reactor

  13. Radiation damage in He implanted silicon at high temperature using multi-energies

    CERN Document Server

    David, M L; Oliviero, E; Denanot, M F; Beaufort, M F; Declemy, A; Blanchard, C; Gerasimenko, N N; Barbot, J F

    2002-01-01

    He sup + ions were implanted at 800 deg. C into (1 0 0) silicon with multiple energies and selected fluences to get a number of displacement per atom constant in a large plateau. The ion-related defects have been mainly studied by transmission electron microscopy. Both the amount and the microstructure of defects have been found to be strongly dependent on the order of implants. Faceted cavities are only observed where damage overlapping occurs. The first implant provides thus nucleation sites for cavities. The generation of these sites is less efficient when using increasing energies because of damage recovery; fewer cavities are observed. Concurrently interstitial-type defects, left brace 1 1 3 right brace agglomerates, are formed. The observed state of growth of these left brace 1 1 3 right brace defects (rod-like and ribbon-like defects) is dependent on the implantation energy order but in any cases, no dislocation loops are observed even in the deepest damage region.

  14. Selection of high temperature thermal energy storage materials for advanced solar dynamic space power systems

    Science.gov (United States)

    Lacy, Dovie E.; Coles-Hamilton, Carolyn; Juhasz, Albert

    1987-01-01

    Under the direction of NASA's Office of Aeronautics and Technology (OAST), the NASA Lewis Research Center has initiated an in-house thermal energy storage program to identify combinations of phase change thermal energy storage media for use with a Brayton and Stirling Advanced Solar Dynamic (ASD) space power system operating between 1070 and 1400 K. A study has been initiated to determine suitable combinations of thermal energy storage (TES) phase change materials (PCM) that result in the smallest and lightest weight ASD power system possible. To date the heats of fusion of several fluoride salt mixtures with melting points greater than 1025 K have been verified experimentally. The study has indicated that these salt systems produce large ASD systems because of their inherent low thermal conductivity and low density. It is desirable to have PCMs with high densities and high thermal conductivities. Therefore, alternate phase change materials based on metallic alloy systems are also being considered as possible TES candidates for future ASD space power systems.

  15. Molecular anion formation in 9,10-anthraquinone: Dependence of the electron detachment rate on temperature and incident electron energy

    Science.gov (United States)

    Pshenichnyuk, Stanislav A.; Vorob'ev, Alexander S.; Asfandiarov, Nail L.; Modelli, Alberto

    2010-06-01

    Attachment of low-energy electrons to gas phase 9,10-anthraquinone (AQ) was observed with electron transmission (ET) spectroscopy, and interpreted with the support of quantum chemical calculations. The ET spectrum displays three shape resonances at 0.45, 0.7, and 2.2 eV, associated with temporary electron capture into empty π∗ molecular orbitals of AQ, the first two anion states being stable. According to TD-B3LYP calculations, the first π-π ∗ core-excited resonance lies at about 1.8 eV, although no experimental evidence for this anion state was found. The long-lived parent molecular anion [AQ]- was observed by means of Electron Attachment Spectroscopy (EAS) using two different mass spectrometers and also by measuring the total anion current at the collision chamber walls. The molecular anion current shows maxima at zero energy, around 0.6 eV and at 1.8 eV. Association of these maxima with the corresponding resonant anion states is discussed. The experimentally measured electron detachment times from [AQ]- as a function of the incident electron energy and the temperature of the target molecule show a pronounced change of slope around 1.5 eV, regardless of the temperature. This unexpected behavior can be qualitatively reproduced within the framework of a multiexponential approach which describes the electron detachment event in terms of a redistribution of the anion excess energy, regardless of the initial mechanism of temporary anion formation.

  16. Research and development program in fiber optic sensors and distributed sensing for high temperature harsh environment energy applications (Conference Presentation)

    Science.gov (United States)

    Romanosky, Robert R.

    2017-05-01

    he National Energy Technology Laboratory (NETL) under the Department of Energy (DOE) Fossil Energy (FE) Program is leading the effort to not only develop near zero emission power generation systems, but to increaser the efficiency and availability of current power systems. The overarching goal of the program is to provide clean affordable power using domestic resources. Highly efficient, low emission power systems can have extreme conditions of high temperatures up to 1600 oC, high pressures up to 600 psi, high particulate loadings, and corrosive atmospheres that require monitoring. Sensing in these harsh environments can provide key information that directly impacts process control and system reliability. The lack of suitable measurement technology serves as a driver for the innovations in harsh environment sensor development. Advancements in sensing using optical fibers are key efforts within NETL's sensor development program as these approaches offer the potential to survive and provide critical information about these processes. An overview of the sensor development supported by the National Energy Technology Laboratory (NETL) will be given, including research in the areas of sensor materials, designs, and measurement types. New approaches to intelligent sensing, sensor placement and process control using networked sensors will be discussed as will novel approaches to fiber device design concurrent with materials development research and development in modified and coated silica and sapphire fiber based sensors. The use of these sensors for both single point and distributed measurements of temperature, pressure, strain, and a select suite of gases will be addressed. Additional areas of research includes novel control architecture and communication frameworks, device integration for distributed sensing, and imaging and other novel approaches to monitoring and controlling advanced processes. The close coupling of the sensor program with process modeling and

  17. Mechanisms Governing the Creep Behavior of High Temperature Alloys for Generation IV Nuclear Energy Systems

    Energy Technology Data Exchange (ETDEWEB)

    Vasudevan, Vijay [Univ. of Cincinnati, OH (United States); Carroll, Laura [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-04-06

    This research project, which includes collaborators from INL and ORNL, focuses on the study of alloy 617 and alloy 800H that are candidates for applications as intermediate heat exchangers in GEN IV nuclear reactors, with an emphasis on the effects of grain size, grain boundaries and second phases on the creep properties; the mechanisms of dislocation creep, diffusional creep and cavitation; the onset of tertiary creep; and theoretical modeling for long-term predictions of materials behavior and for high temperature alloy design.

  18. Determining the ion temperature and energy distribution in a lithium-plasma interaction test stand with a retarding field energy analyzer

    Science.gov (United States)

    Christenson, M.; Stemmley, S.; Jung, S.; Mettler, J.; Sang, X.; Martin, D.; Kalathiparambil, K.; Ruzic, D. N.

    2017-08-01

    The ThermoElectric-driven Liquid-metal plasma-facing Structures (TELS) experiment at the University of Illinois is a gas-puff driven, theta-pinch plasma source that is used as a test stand for off-normal plasma events incident on materials in the edge and divertor regions of a tokamak. The ion temperatures and resulting energy distributions are crucial for understanding how well a TELS pulse can simulate an extreme event in a larger, magnetic confinement device. A retarding field energy analyzer (RFEA) has been constructed for use with such a transient plasma due to its inexpensive and robust nature. The innovation surrounding the use of a control analyzer in conjunction with an actively sampling analyzer is presented and the conditions of RFEA operation are discussed, with results presented demonstrating successful performance under extreme conditions. Such extreme conditions are defined by heat fluxes on the order of 0.8 GW m-2 and on time scales of nearly 200 μs. Measurements from the RFEA indicate two primary features for a typical TELS discharge, following closely with the pre-ionizing coaxial gun discharge characteristics. For the case using the pre-ionization pulse (PiP) and the theta pinch, the measured ion signal showed an ion temperature of 23.3 ± 6.6 eV for the first peak and 17.6 ± 1.9 eV for the second peak. For the case using only the PiP, the measured signal showed an ion temperature of 7.9 ± 1.1 eV for the first peak and 6.6 ± 0.8 eV for the second peak. These differences illustrate the effectiveness of the theta pinch for imparting energy on the ions. This information also highlights the importance of TELS as being one of the few linear pulsed plasma sources whereby moderately energetic ions will strike targets without the need for sample biasing.

  19. Mechanisms of importance for the formation of granules in an UASB reactors; Mekanismer af betydning for dannelse af granula i UASB-reaktorer

    Energy Technology Data Exchange (ETDEWEB)

    Winther-Nielsen, M.

    1991-12-31

    Thermophilic granules exhibiting good stabilities were successfully developed on glucose, acetate, and a mixture of acetate, propionate, and butyrate. The only genus of aceticlastic methanogens identified in the granules were Methanosarcina spp. An examination of the influence of temperature proved that the conversion of propionate was greatly effected by temperature variations, contrary to the conversions of acetate and butyrate. By operating a 5 litre UASB reactor with a great axial temperature gradient in the sludge bed of the reactor, an establishment of a propionate converting population in the granular sludge was disturbed. Following a reduction of the temperature variation by an increase of the temperature of the influent, the conversion of propionate was enhanced and the granule size was increased significantly. The effects of phosphate concentration between 0 and 10 mM on acetate-grown granules were investigated at 55 deg. C. No significant effect on the size of granules and apprently no essential influence on the specific acetate consumption rates in the reactors were found after 5 mounths of operation. Phosphate accumulation was observed in the reactors and was dependent on the phosphate concentration in the influent. These indicate that phosphate removal from waste waters may be performed in anaerobic systems. The influence of the superficial liquid flow rate on the formation of granules was studied in two thermophilic UASB reactors on glucose. Granules were observed earlier in the reactor which had the highest flow rate and the size of granules was still significantly larger in this reactor during steady-state condition. (author) 157 refs.

  20. Low energy dislocation structures due to unidirectional deformation at low temperatures

    DEFF Research Database (Denmark)

    Hansen, Niels; Kuhlmann-Wilsdorf, D.

    1986-01-01

    , correspondingly leaving the major fraction of the volume free of dislocations. The value of R decreases in the following order: pile-ups to dipolar mats, Taylor lattices, tilt and dipolar walls to dislocation cell structures. This is the same order in which dislocation structures tend to develop with increasing......” cell structure; (iii) suggestions are made to account for microband formation on the basis of energy minimization. Finally, the relationship between surface markings and the underlying dislocation structure is discussed and related to slip processes taking place during uniaxial deformation....

  1. Temperature Effect of Hydrogen-Like Impurity on the Ground State Energy of Strong Coupling Polaron in a RbCl Quantum Pseudodot

    Science.gov (United States)

    Xiao, Jing-Lin

    2016-11-01

    We study the ground state energy and the mean number of LO phonons of the strong-coupling polaron in a RbCl quantum pseudodot (QPD) with hydrogen-like impurity at the center. The variations of the ground state energy and the mean number of LO phonons with the temperature and the strength of the Coulombic impurity potential are obtained by employing the variational method of Pekar type and the quantum statistical theory (VMPTQST). Our numerical results have displayed that [InlineMediaObject not available: see fulltext.] the absolute value of the ground state energy increases (decreases) when the temperature increases at lower (higher) temperature regime, [InlineMediaObject not available: see fulltext.] the mean number of the LO phonons increases with increasing temperature, [InlineMediaObject not available: see fulltext.] the absolute value of ground state energy and the mean number of LO phonons are increasing functions of the strength of the Coulombic impurity potential.

  2. Rechargeable Lithium Sulfur (Li-S) Battery with Specific Energy 400 Wh/kg and Operating Temperature Range -60?C to 60?C Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Sion Power is developing a rechargeable lithium sulfur (Li-S) battery with a demonstrated specific energy exceeding 350 Wh/kg and the range of operating temperatures...

  3. Embedding of $^{163}$Ho and $^{166m}$ Ho in the energy absorbers of low temperature metallic magnetic calorimeters

    CERN Multimedia

    The calorimetric measurement of the $^{163}$Ho electron capture spectrum is a promising tool to investigate the electron neutrino mass. A suitable method to embed the source in the detectors is the ion-implantation. This process has already been used to embed $^{163}$Ho ions in micro-fabricated low temperature metallic magnetic prototypes. The $^{163}$Ho electron capture spectrum obtained with these first prototypes is presently the most precise with an energy resolution of $\\Delta$$\\textit{E}$$_{FWHM}$ = 7.6 eV. In order to test the performance of the new generation of low temperature metallic magnetic calorimeters, we propose to perform a $^{163}$Ho ion-implantation on the new chip having two arrays consisting of 32 pixels each. An activity of about 1 Bq per pixel is required. With this new detector array we will be able to achieve a better energy resolution and to acquire a higher statistics which allows for studying the $^{163}$Ho spectral shape. We propose also to perform an ion-implantation of $^{166m}$...

  4. Capital cost expenditure of high temperature latent and sensible thermal energy storage systems

    Science.gov (United States)

    Jacob, Rhys; Saman, Wasim; Bruno, Frank

    2017-06-01

    In the following study cost estimates have been undertaken for an encapsulated phase change material (EPCM) packed bed, a packed bed thermocline and a traditional two-tank molten salt system. The effect of various heat transfer fluids (air and molten salt), system configuration (cascade vs one PCM, and direct vs indirect) and temperature difference (ΔT = 100-500 °C) on the cost estimate of the system was also investigated. Lastly, the storage system boundary was expanded to include heat exchangers, pumps and fans, and heat tracing so that a thorough cost comparison could be undertaken. The results presented in this paper provide a methodology to quickly compare various systems and configurations while providing design limits for the studied technologies.

  5. Optimal thermionic energy conversion with established electrodes for high-temperature topping and process heating. [coal combustion product environments

    Science.gov (United States)

    Morris, J. F.

    1980-01-01

    Applied research-and-technology (ART) work reveals that optimal thermionic energy conversion (TEC) with approximately 1000 K to approximately 1100 K collectors is possible using well established tungsten electrodes. Such TEC with 1800 K emitters could approach 26.6% efficiency at 27.4 W/sq cm with approximately 1000 K collectors and 21.7% at 22.6 W/sq cm with approximately 1100 K collectors. These performances require 1.5 and 1.7 eV collector work functions (not the 1 eV ultimate) with nearly negligible interelectrode losses. Such collectors correspond to tungsten electrode systems in approximately 0.9 to approximately 6 torr cesium pressures with 1600 K to 1900 K emitters. Because higher heat-rejection temperatures for TEC allow greater collector work functions, interelectrode loss reduction becomes an increasingly important target for applications aimed at elevated temperatures. Studies of intragap modifications and new electrodes that will allow better electron emission and collection with lower cesium pressures are among the TEC-ART approaches to reduced interelectrode losses. These solutions will provide very effective TEC to serve directly in coal-combustion products for high-temperature topping and process heating. In turn this will help to use coal and to use it well.

  6. A New Equation Relating the Viscosity Arrhenius Temperature and the Activation Energy for Some Newtonian Classical Solvents

    Directory of Open Access Journals (Sweden)

    Aymen Messaâdi

    2015-01-01

    Full Text Available In transport phenomena, precise knowledge or estimation of fluids properties is necessary, for mass flow and heat transfer computations. Viscosity is one of the important properties which are affected by pressure and temperature. In the present work, based on statistical techniques for nonlinear regression analysis and correlation tests, we propose a novel equation modeling the relationship between the two parameters of viscosity Arrhenius-type equation, such as the energy (Ea and the preexponential factor (As. Then, we introduce a third parameter, the Arrhenius temperature (TA, to enrich the model and the discussion. Empirical validations using 75 data sets of viscosity of pure solvents studied at different temperature ranges are provided from previous works in the literature and give excellent statistical correlations, thus allowing us to rewrite the Arrhenius equation using a single parameter instead of two. In addition, the suggested model is very beneficial for engineering data since it would permit estimating the missing parameter value, if a well-established estimate of the other parameter is readily available.

  7. Analysis for fin efficiency with temperature-dependent thermal conductivity of fractional order energy balance equation using HPST Method

    Directory of Open Access Journals (Sweden)

    A. Patra

    2016-03-01

    Full Text Available Radiating extended surfaces are usually utilized to enhance the heat transfer between primary surface and the environment. In this paper, temperature distribution, fin efficiency, efficacy of convective straight fins with constant and temperature-dependent thermal conductivity are solved by implementing homotopy perturbation sumudu transform method (HPSTM. The proposed method is very useful and practical for solving the fractional order nonlinear diffusion equation, which is associated with variable thermal conductivity condition. A dimensionless analytical expression has been developed for fin effectiveness. The fin efficiency and the fin effectiveness have been attained as a function of thermo-geometric fin parameter. It can be noticed that the thermal conductivity parameter has a strong influence over the fin efficiency. The analytical solutions acquired by the present method illustrate the approach is easy to implement and computationally very interesting. The obtained results are compared with previously found classical order results using variational iteration method (VIM, Adomian decomposition method, and the results from Galerkin method in order to show the competence of this present method. HPSTM is a simple and effective method for rapid assessment of physical systems although the fractional order energy balance equations comprise with strong nonlinear terms. The subsequent correlation equations can benefit thermal design engineers for designing of innovative straight fins with both constant and temperature-dependent thermal conductivity.

  8. 2D Temperature Analysis of Energy and Exergy Characteristics of Laminar Steady Flow across a Square Cylinder under Strong Blockage

    Directory of Open Access Journals (Sweden)

    M. Ozgun Korukcu

    2015-05-01

    Full Text Available Energy and exergy characteristics of a square cylinder (SC in confined flow are investigated computationally by numerically handling the steady-state continuity, Navier-Stokes and energy equations in the Reynolds number range of Re = 10–50, where the blockage ratio (β = B/H is kept constant at the high level of β = 0.8. Computations indicated for the upstream region that, the mean non-dimensional streamwise (u/Uo and spanwise (v/Uo velocities attain the values of u/Uo = 0.840®0.879 and v/Uo = 0.236®0.386 (Re = 10®50 on the front-surface of the SC, implying that Reynolds number and blockage have stronger impact on the spanwise momentum activity. It is determined that flows with high Reynolds number interact with the front-surface of the SC developing thinner thermal boundary layers and greater temperature gradients, which promotes the thermal entropy generation values as well. The strict guidance of the throat, not only resulted in the fully developed flow character, but also imposed additional cooling; such that the analysis pointed out the drop of duct wall (y = 0.025 m non-dimensional temperature values (ζ from ζ = 0.387®0.926 (Re = 10®50 at xth = 0 mm to ζ = 0.002®0.266 at xth = 40 mm. In the downstream region, spanwise thermal disturbances are evaluated to be most inspectable in the vortex driven region, where the temperature values show decrease trends in the spanwise direction. In the corresponding domain, exergy destruction is determined to grow with Reynolds number and decrease in the streamwise direction (xds = 0®10 mm. Besides, asymmetric entropy distributions as well were recorded due to the comprehensive mixing caused by the vortex system.

  9. Entropy, temperature and internal energy of trapped gravitons and corrections to the Black Hole entropy

    Science.gov (United States)

    Viaggiu, Stefano

    2017-12-01

    In this paper we study the proposal present in Viaggiu (2017) concerning the statistical description of trapped gravitons and applied to derive the semi-classical black hole (BH) entropy SBH. We study the possible configurations depending on physically reasonable expressions for the internal energy U. In particular, we show that expressions for U ∼Rk , k ≥ 1, with R the radius of the confining spherical box, can have a semi-classical description, while behaviors with k physically motivated expression for U(R) , we obtain the well known logarithmic corrections to the BH entropy, with the usual behaviors present in the literature of BH entropy. Moreover, a phase transition emerges with a positive specific heat C at Planckian lengths instead of the usual negative one at non-Planckian scales, in agreement with results present in the literature. Finally, we show that evaporation stops at a radius R of the order of the Planck length.

  10. Feasibility study of underground energy storage using high-pressure, high-temperature water. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Dooley, J.L.; Frost, G.P.; Gore, L.A.; Hammond, R.P.; Rawson, D.L.; Ridgway, S.L.

    1977-01-01

    A technical, operational and economic feasibility study on the storage of energy as heated high pressure water in underground cavities that utilize the rock overburden for containment is presented. Handling peak load requirements of electric utility power networks is examined in some detail. The cavity is charged by heating water with surplus steaming capacity during periods of low power requirement. Later this hot water supplies steam to peaking turbines when high load demands must be met. This system can be applied to either new or existing power plants of nuclear or fossil fuel type. The round trip efficiency (into storage and back) is higher than any other system - over 90%. Capital costs are competitive and the environmental impact is quite benign. Detailed installation and design problems are studied and costs are estimated. The continental United States is examined for the most applicable geology. Formations favorable for these large cavities exist in widespread areas.

  11. Temperature Dependence of Energy Gap in the Superconducting State in URu2Si2

    Science.gov (United States)

    Bourdarot, Frederic; Hassinger, Elena; Raymond, Stephane; Aoki, Dai; Taufour, Valentin; Flouquet, Jacques

    2010-09-01

    The excitation spectrum of URu2Si2 in the superconducting state has been investigated by a precise neutron-scattering experiment. A weak but clear positive energy shift of ˜40 μeV has been detected in the superconducting phase (at T=400 mK) for the resonance at Q0 = (1,0,0). For the resonance at Q1 = (0.6,0,0), a two times smaller shift is observed but with an incertitude of the same order than this shift. This result is in agreement with our previous results indicating that the wave-vector Q0 is connected with the order parameters of the hidden order and of superconductivity.

  12. Use and Storage of Test and Operations Data from the High Temperature Test Reactor Acquired by the US Government from the Japan Atomic Energy Agency

    Energy Technology Data Exchange (ETDEWEB)

    Hans Gougar

    2010-02-01

    This document describes the use and storage of data from the High Temperature Test Reactor (HTTR) acquired from the Japan Atomic Energy Agency (JAEA) by the U.S. Government for high temperature reactor research under the Next Generation Nuclear Plant (NGNP) Project.

  13. Wheel-running activity and energy metabolism in relation to ambient temperature in mice selected for high wheel-running activity

    NARCIS (Netherlands)

    Vaanholt, Lobke M.; Garland, Theodore; Daan, Serge; Visser, G. Henk; Garland Jr., Theodore; Heldmaier, G.

    Interrelationships between ambient temperature, activity, and energy metabolism were explored in mice that had been selectively bred for high spontaneous wheel-running activity and their random-bred controls. Animals were exposed to three different ambient temperatures (10, 20 and 30 degrees C) and

  14. Rancang Bangun Model Alat Uji Teras Reaktor Nuklir Small Modular Reactor (SMR) Dengan Fluida Pendingin H2O Untuk Kondisi Konveksi Paksa

    OpenAIRE

    Ramadhan, Anwar Ilmar; Dermawan, Erwin; Diniardi, Ery; Arifangga, Muhammad

    2015-01-01

    Heat transfer performance poor will have a negative impact on the reactor system which in turn could affect the release of radioactive substances into the surrounding environment so as to endanger the safety of the environment and living things that exist around the reactor. The purpose of this research is to create or design a testing tool wake models in a nuclear reactor core in a laboratory scale assuming cylindrical heat derived from the electrical energy that does not harm the environmen...

  15. Low Temperature Plasma Science: Not Only the Fourth State of Matter but All of Them. Report of the Department of Energy Office of Fusion Energy Sciences Workshop on Low Temperature Plasmas, March 25-57, 2008

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-09-01

    Low temperature plasma science (LTPS) is a field on the verge of an intellectual revolution. Partially ionized plasmas (often referred to as gas discharges) are used for an enormous range of practical applications, from light sources and lasers to surgery and making computer chips, among many others. The commercial and technical value of low temperature plasmas (LTPs) is well established. Modern society would simply be less advanced in the absence of LTPs. Much of this benefit has resulted from empirical development. As the technology becomes more complex and addresses new fields, such as energy and biotechnology, empiricism rapidly becomes inadequate to advance the state of the art. The focus of this report is that which is less well understood about LTPs - namely, that LTPS is a field rich in intellectually exciting scientific challenges and that addressing these challenges will result in even greater societal benefit by placing the development of plasma technologies on a solid science foundation. LTPs are unique environments in many ways. Their nonequilibrium and chemically active behavior deviate strongly from fully ionized plasmas, such as those found in magnetically confined fusion or high energy density plasmas. LTPs are strongly affected by the presence of neutral species-chemistry adds enormous complexity to the plasma environment. A weakly to partially ionized gas is often characterized by strong nonequilibrium in the velocity and energy distributions of its neutral and charged constituents. In nonequilibrium LTP, electrons are generally hot (many to tens of electron volts), whereas ions and neutrals are cool to warm (room temperature to a few tenths of an electron volt). Ions and neutrals in thermal LTP can approach or exceed an electron volt in temperature. At the same time, ions may be accelerated across thin sheath boundary layers to impact surfaces, with impact energies ranging up to thousands of electron volts. These moderately energetic electrons

  16. EPB standard EN ISO 52016: calculation of the building’s energy needs for heating and cooling, internal temperatures and heating and cooling load

    NARCIS (Netherlands)

    Dijk, H.A.L. van; Spiekman, M.E.; Hoes-van Oeffelen, E.C.M.

    2016-01-01

    EN ISO 52016-1 presents a coherent set of calculation methods at different levels of detail, for the (sensible) energy needs for the space heating and cooling and (latent) energy needs (de)humidification of a building and/or internal temperatures and heating and/or cooling loads, including the

  17. In-situ experimental characterization of the clamping pressure effects on low temperature polymer electrolyte membrane electrolysis International Journal of Hydrogen Energy

    DEFF Research Database (Denmark)

    Al Shakhshir, Saher; Cui, Xiaoti; Frensch, Steffen Henrik

    2017-01-01

    The recent acceleration in hydrogen production’s R&D will lead the energy transition. Low temperature polymer electrolyte membrane electrolysis (LT-PEME) is one of the most promising candidate technologies to produce hydrogen from renewable energy sources, and for synthetic fuel production. LT-PE...

  18. ANALISIS KUAT SUMBER NEUTRON DAN PERHITUNGAN LAJU DOSIS NEUTRON TERAS AWAL RDE

    Directory of Open Access Journals (Sweden)

    Suwoto Suwoto

    2017-02-01

    Full Text Available Teras reaktor RDE (Reaktor Daya Eksperimental berbentuk silinder non anular, mengadopsi teknologi HTGR (High Temperature Gas-cooled Reactor berbahan bakar kernel partikel berlapis TRISO dalam bentuk bola (pebble dan berpendingin gas helium. Desain teras reaktor RDE ini mengadopsi teknologi reaktor temperatur tinggi HTGR dengan keselamatan inherent pasif yang sangat aman. Temperatur keluaran panas gas helium teras reaktor RDE dirancang pada kisaran 700°C dengan temperatur masukan sekitar 250°C. Di samping menghasilkan listrik, reaktor RDE didisain menghasilkan panas temperatur tinggi yang dapat digunakan untuk keperluan kogenerasi lainnya (penelitian panas proses lainnya. Bahan bakar pada RDE berbentuk bola yang berisikan kernel partikel berlapis TRISO yang berupa uranium oksida (UO2 berpengkayaan 17%. Lapisan TRISO terdiri 4 lapisan yaitu lapisan karbon penyangga berpori, lapisan karbon pirolitik bagian dalam (IPyC, Inner Pyrolitic Carbon, lapisan Silikon Karbida (SiC dan lapisan pirolitik karbon bagian luar (OPyC, OuterPyrolitic Carbon. Analisis kuat sumber dan perhitungan awal laju dosis neutron pada teras RDE dilakukan menggunakan program Monte Carlo MCNP5v1.2. Pemodelan heterogenitas ganda pada bahan bakar kernel partikel berlapis TRISO dan pada bahan bakar bola pada teras RDE. Dengan memanfaatkan program EGS99304, jumlah struktur group energi yaitu 640 (SAND-II group structure digunakan dalam perhitungan spektrum neutron pada reaktor RDE. Teras reaktor RDE dibagi dalam 100 zona (10 arah radial dan 10 arah aksial. Analisis hasil perhitungan menunjukkan bahwa kuat sumber neutron reaktor RDE sebesar 8,47027X1017 neutron/sekon. Distribusi laju dosis neutron ditentukan menggunakan faktor konversi fluks ke dosis neurton dari International Commission on Radiological Protection, ICRP dan NCRP. Hasil perhitungan awal laju dosis neutron dengan faktor konversi ICRP-21 dan NCRP-38 untuk pekerja radiasi pada arah radial di perisai biologis sudah

  19. New graphite/salt materials for high temperature energy storage. Phase change properties study; Nouveaux materiaux graphite/sel pour le stockage d'energie a haute temperature. Etude des proprietes de changement de phase

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, J

    2007-07-15

    This work is a contribution to the study of new graphite/salt composites dedicated to high temperature energy storage ({>=}200 C). The aim is to analyse and to understand the influence of both graphite and composite microstructure on the phase change properties of salts. This PhD is carried out within the framework of two projects: DISTOR (European) and HTPSTOCK (French). The major contributions of this work are threefold: 1) An important database (solid-liquid phase change properties) is provided from the DSC analysis of six salts and the corresponding composites. 2) Rigorous modeling of salts melting in confined media in several geometries are proposed to understand why, during the first melting of the compression elaborated composites, problems of salt leakage are observed. These models show that the materials morphology is responsible for these phenomena: the graphite matrix restrains the volume expansion due to salt melting: salt melts under pressure, which leads to a melting on a large temperature range and to a loss of energy density. Sensitivity analysis of parameters (geometric and physic) shows that matrix rigidity modulus is the parameter on which it is necessary to act during the composites elaboration to blur this phenomenon. 3) Finally, this work proposes a thermodynamic formulation of both surface/interface phenomena and the presence of dissolved impurities being able to explain a melting point lowering. It seems that the melting point lowering observed ({approx} 5 C) are mainly due to the presence of dissolved impurities (brought by graphite) in the liquid, along with an additional Gibbs-Thomson effect ({approx} 1 C, related to the size of the clusters crystals). (author)

  20. Distributed Optical Fiber Radiation and Temperature Sensing at High Energy Accelerators and Experiments

    CERN Document Server

    AUTHOR|(CDS)2090137; Brugger, Markus

    The aim of this Thesis is to investigate the feasibility of a distributed optical fiber radiation sensing system to be used at high energy physics accelerators and experiments where complex mixed-field environments are present. In particular, after having characterized the response of a selection of radiation sensitive optical fibers to ionizing radiation coming from a 60Co source, the results of distributed optical fiber radiation measurements in a mixed-field environment are presented along with the method to actually estimate the dose variation. This study demonstrates that distributed optical fiber dosimetry in the above mentioned mixed-field radiation environment is feasible, allowing to detect dose variations of about 10-15 Gy with a 1 m spatial resolution. The proof of principle has fully succeeded and we can now tackle the challenge of an industrial installation taking into account that some optimizations need to be done both on the control unit of the system as well as on the choice of the sensing f...

  1. Energy

    CERN Document Server

    Foland, Andrew Dean

    2007-01-01

    Energy is the central concept of physics. Unable to be created or destroyed but transformable from one form to another, energy ultimately determines what is and isn''t possible in our universe. This book gives readers an appreciation for the limits of energy and the quantities of energy in the world around them. This fascinating book explores the major forms of energy: kinetic, potential, electrical, chemical, thermal, and nuclear.

  2. A High Temperature Electrochemical Energy Storage System Based on Sodium Beta-Alumina Solid Electrolyte (Base)

    Energy Technology Data Exchange (ETDEWEB)

    Anil Virkar

    2008-03-31

    AlO{sub 2} is never formed. Conversion occurs by a coupled transport of Na{sup +} through BASE formed and of O{sup 2-} through YSZ to the reaction front. Transport to the reaction front is described in terms of a chemical diffusion coefficient of Na{sub 2}O. The conversion kinetics as a function of microstructure is under investigation. The mechanism of conversion is described in this report. A number of discs and tubes of BASE have been fabricated by the vapor phase process. The material was investigated by X-ray diffraction (XRD), optical microscopy and scanning electron microscopy (SEM), before and after conversion. Conductivity (which is almost exclusively due to sodium ion transport at the temperatures of interest) was measured. Conductivity was measured using sodium-sodium tests as well as by impedance spectroscopy. Various types of both planar and tubular electrochemical cells were assembled and tested. In some cases the objective was to determine if there was any interaction between the salt and BASE. The interaction of interest was mainly ion exchange (possible replacement of sodium ion by the salt cation). It was noted that Zn{sup 2+} did not replace Na+ over the conditions of interest. For this reason much of the work was conducted with ZnCl{sub 2} as the cathode salt. In the case of Sn-based, Sn{sup 2+} did ion exchange, but Sn{sup 4+} did not. This suggests that Sn{sup 4+} salts are viable candidates. These results and implications are discussed in the report. Cells made with Na as the anode and ZnCl{sub 2} as the cathode were successfully charged/discharged numerous times. The key advantages of the batteries under investigation here over the Na-S batteries are: (1) Steel wool can be used in the cathode compartment unlike Na-S batteries which require expensive graphite. (2) Planar cells can be constructed in addition to tubular, allowing for greater design flexibility and integration with other devices such as planar SOFC. (3) Comparable or higher open circuit

  3. Neuro-fuzzy dynamic model with Kalman filter to forecast irradiance and temperature for solar energy systems

    Energy Technology Data Exchange (ETDEWEB)

    Chaabene, Maher; Ben Ammar, Mohsen [The High Institute of Technological Studies (ISET), Sfax (Tunisia); Unite de commande de machines et energies renouvelables CMER, ENIS (Tunisia)

    2008-07-15

    This paper introduces a dynamic forecasting of irradiance and ambient temperature. The medium term forecasting (MTF) gives a daily meteorological behaviour. It consists of a neuro-fuzzy estimator based on meteorological parameters' behaviours during the days before, and on time distribution models. As for the short term forecasting (STF), it estimates, for a 5 min time step ahead, the meteorological parameters evolution. It is ensured by the Auto-Regressive Moving Average (ARMA) model of the MTF associated to a Kalman filter. STF uses instantaneous measured data, delivered by a data acquisition system, so as to accomplish the forecast. Herein we describe our method and we present forecasting results. Validation is based on measurements taken at the Energy and Thermal Research Centre (CRTEn) in the north of Tunisia. Since our work delivers accurate meteorological parameters forecasting, the obtained results can be easily adapted to forecast any solar conversion system output. (author)

  4. Estimating morning change in land surface temperature from MODIS day/night observations: Applications for surface energy balance modeling

    Science.gov (United States)

    Hain, Christopher R.; Anderson, Martha C.

    2017-10-01

    Observations of land surface temperature (LST) are crucial for the monitoring of surface energy fluxes from satellite. Methods that require high temporal resolution LST observations (e.g., from geostationary orbit) can be difficult to apply globally because several geostationary sensors are required to attain near-global coverage (60°N to 60°S). While these LST observations are available from polar-orbiting sensors, providing global coverage at higher spatial resolutions, the temporal sampling (twice daily observations) can pose significant limitations. For example, the Atmosphere Land Exchange Inverse (ALEXI) surface energy balance model, used for monitoring evapotranspiration and drought, requires an observation of the morning change in LST—a quantity not directly observable from polar-orbiting sensors. Therefore, we have developed and evaluated a data-mining approach to estimate the midmorning rise in LST from a single sensor (two observations per day) of LST from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensor on the Aqua platform. In general, the data-mining approach produced estimates with low relative error (5 to 10%) and statistically significant correlations when compared against geostationary observations. This approach will facilitate global, near-real-time applications of ALEXI at higher spatial and temporal coverage from a single sensor than currently achievable with current geostationary data sets.

  5. The Application of Thermal Solar Energy to High Temperature Processes: Case Study of the Synthesis of Alumina from Boehmite

    Directory of Open Access Journals (Sweden)

    Isabel Padilla

    2014-01-01

    Full Text Available The aim of this paper is to evaluate the feasibility of obtaining alumina from boehmite using a free, clean, and unlimited power source as the solar energy. Boehmite was obtained by hydrothermal treatment of a hazardous waste coming from aluminum slag milling. The waste is considered as a hazardous substance because of it releasing toxic gases (hydrogen, ammonia, methane, and hydrogen sulfide in the presence of water. The as-obtained boehmite was transformed into alumina, in air atmosphere, using a solar energy concentrator (Fresnel lens. The solar installation provides a power density of 260 W·cm−2 which allows reaching temperatures upper than 1000°C at few minutes of exposure. Tests were performed at different periods of time that ranged between 5 and 90 min. The percentage of transformation of boehmite into alumina was followed by the water content of samples after solar radiation exposure. Samples were characterized by X-ray diffraction, infrared spectroscopy, and thermogravimetry. Metastable aluminas started to appear at 5 min and the crystalline and stable phase corundum at 10 min of solar radiation exposure.

  6. Novel low temperature, low energy and high efficiency pretreatment technology for large wood chips with a redox couple catalyst.

    Science.gov (United States)

    Gogoi, Parikshit; Zhang, Zhe; Geng, Zhishuai; Liu, Wei; Hu, Weize; Deng, Yulin

    2018-01-23

    Pretreatment of lignocellulosic biomass plays a vital role in the conversion of cellulosic biomass to bioethanol, specially for softwoods and hardwoods. Although many pretreatment technologies have been reported so far, but barely a few pretreatment methods can handle large sized wood chips directly. To improve the efficiency of this pretreatment all the existing technologies need to grind wood into small particles, which is an extreme energy consuming process. Herein, for the first time, we report a simple, effective and low temperature (~100 oC) process for pretreatment of hardwood (HW) and softwood (SW) chips directly by using a catalytic system of FeCl3/NaNO3 redox couple (FCSNRC). The pretreatment experiments were systematically conducted and a conversion of 71.53% and 70.66% of cellulose to sugar could be obtained even large sized hard and softwood chips being directly used. The novel method reported here overcame one of the critical barriers in biomass to biofuel conversion and both grinding and thermal energies can be significantly reduced. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. The Development of an INL Capability for High Temperature Flow, Heat Transfer, and Thermal Energy Storage with Applications in Advanced Small Modular Reactors, High Temperature Heat Exchangers, Hybrid Energy Systems, and Dynamic Grid Energy Storage C

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Xiaodong [The Ohio State Univ., Columbus, OH (United States); Zhang, Xiaoqin [The Ohio State Univ., Columbus, OH (United States); Kim, Inhun [The Ohio State Univ., Columbus, OH (United States); O' Brien, James [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-10-01

    The overall goal of this project is to support Idaho National Laboratory in developing a new advanced high temperature multi fluid multi loop test facility that is aimed at investigating fluid flow and heat transfer, material corrosion, heat exchanger characteristics and instrumentation performance, among others, for nuclear applications. Specifically, preliminary research has been performed at The Ohio State University in the following areas: 1. A review of fluoride molten salts’ characteristics in thermal, corrosive, and compatibility performances. A recommendation for a salt selection is provided. Material candidates for both molten salt and helium flow loop have been identified. 2. A conceptual facility design that satisfies the multi loop (two coolant loops [i.e., fluoride molten salts and helium]) multi purpose (two operation modes [i.e., forced and natural circulation]) requirements. Schematic models are presented. The thermal hydraulic performances in a preliminary printed circuit heat exchanger (PCHE) design have been estimated. 3. An introduction of computational methods and models for pipe heat loss analysis and cases studies. Recommendations on insulation material selection have been provided. 4. An analysis of pipe pressure rating and sizing. Preliminary recommendations on pipe size selection have been provided. 5. A review of molten fluoride salt preparation and chemistry control. An introduction to the experience from the Molten Salt Reactor Experiment at Oak Ridge National Laboratory has been provided. 6. A review of some instruments and components to be used in the facility. Flowmeters and Grayloc connectors have been included. This report primarily presents the conclusions drawn from the extensive review of literatures in material selections and the facility design progress at the current stage. It provides some useful guidelines in insulation material and pipe size selection, as well as an introductory review of facility process and components.

  8. Geological exploration for a high-temperature aquifer thermal energy storage (HT-ATES) system: a case study from Oman

    Science.gov (United States)

    Winterleitner, Gerd; Schütz, Felina; Huenges, Ernst

    2017-04-01

    A collaborative research programme between the German Research Centre for Geoscience, Potsdam (GFZ) and The Research Council of Oman (TRC) is underway, which aims to develop and implement an innovative concept of a sustainable thermally driven cooling system in combination with a HT-ATES in northern Oman. The system will use an absorption chiller for cold supply, which nominally requires water of around 100°C as energy source. Solar collectors will provide this thermal energy and energy surpluses during daytimes will be stored to ensure a continuous operation of the cooling system. An integral part of this project is, therefore, the development of an efficient HT-ATES (100°C), which is based on temporary storage and recovery of thermal energy through hot water injection in subsurface aquifer horizons. Thus, an accurate thermal and fluid flow characterisation of potential reservoir horizons is essential to ensure optimal efficiency of the cooling system. The study area is located in the Al Khwad area, approximately 40 km to the west of Muscat. The area is characterised by a thick Cenozoic mixed carbonate-siliciclastic sedimentary succession, containing at least 3 aquifer horizons. We use a multidisciplinary approach for the initial ATES exploration and development phase, including traditional geological fieldwork dovetailed with virtual outcrop geology, thin-section analyses, geological modelling and reservoir fluid flow forecasting analyses. Our first results indicate two potential storage horizons: (1) a Miocene-aged clastic-dominated alluvial fan system and (2) an Eocene carbonate-dominated sequence. The alluvial fan system is characterised by a more than 300 m thick, coarse-clastic succession of coalesced individual fans. Thermal and hydraulic parameters are favourable for gravel and sandstone intervals but reservoir architecture is complex due to multiple generations of interconnecting fans with highly heterogeneous facies distributions. The Eocene carbonates

  9. Relationship between wind energy production and temperature over the November 2010-February 2011 period; Relation entre production eolienne et temperature sur la periode de Novembre 2010 a Fevrier 2011

    Energy Technology Data Exchange (ETDEWEB)

    Flocard, H.

    2011-07-01

    As consumption peaks occur during the coldest periods between November and February, the author used some data published by RTE to assess the wind energy share during these periods. The author comments the wind energy daily production data with respect to daily average temperatures measured on a given site. As there is no wind when the weather is very cold, it appears that this renewable energy will not help France to face the challenge of future winter peaks. On the other hand, wind energy production is higher when electricity demand is lower. Therefore, he concludes that the management of the production-consumption balance will become more difficult as the installed wind energy power will increase

  10. Minimum daily core body temperature in western grey kangaroos decreases as summer advances: a seasonal pattern, or a direct response to water, heat or energy supply?

    Science.gov (United States)

    Maloney, Shane K; Fuller, Andrea; Meyer, Leith C R; Kamerman, Peter R; Mitchell, Graham; Mitchell, Duncan

    2011-06-01

    Using implanted temperature loggers, we measured core body temperature in nine western grey kangaroos every 5 min for 24 to 98 days in spring and summer. Body temperature was highest at night and decreased rapidly early in the morning, reaching a nadir at 10:00 h, after ambient temperature and solar radiation had begun to increase. On hotter days, the minimum morning body temperature was lower than on cooler days, decreasing from a mean of 36.2°C in the spring to 34.0°C in the summer. This effect correlated better with the time of the year than with proximate thermal stressors, suggesting that either season itself or some factor correlated with season, such as food availability, caused the change. Water saving has been proposed as a selective advantage of heterothermy in other large mammals, but in kangaroos the water savings would have been small and not required in a reserve with permanent standing water. We calculate that the lower core temperature could provide energy savings of nearly 7%. It is likely that the heterothermy that we observed on hot days results either from decreased energy intake during the dry season or from a seasonal pattern entrained in the kangaroos that presumably has been selected for because of decreased energy availability during the dry season.

  11. Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash, Cow Manure, and Microalgae: A Simulation Study.

    Science.gov (United States)

    Hanif, Muhammad Usman; Capareda, Sergio C; Iqbal, Hamid; Arazo, Renato Ortiz; Baig, Muhammad Anwar

    2016-01-01

    The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata]) through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%), 600°C for syngas (22 wt%), and 551°C for bio-oil (48 wt%). Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products.

  12. Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash, Cow Manure, and Microalgae: A Simulation Study

    Science.gov (United States)

    Hanif, Muhammad Usman; Capareda, Sergio C.; Iqbal, Hamid; Arazo, Renato Ortiz; Baig, Muhammad Anwar

    2016-01-01

    The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata]) through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%), 600°C for syngas (22 wt%), and 551°C for bio-oil (48 wt%). Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products. PMID:27043929

  13. Effects of Pyrolysis Temperature on Product Yields and Energy Recovery from Co-Feeding of Cotton Gin Trash, Cow Manure, and Microalgae: A Simulation Study.

    Directory of Open Access Journals (Sweden)

    Muhammad Usman Hanif

    Full Text Available The intensive search of new and cleaner energy catches interest in recent years due to huge consumption of fossil fuels coupled with the challenge of energy and environmental sustainability. Production of renewable and environmentally benign energy from locally available raw materials is coming in the frontline. In this work, conversion of the combined biomass (cotton gin trash, cow manure, and Microalgae [Nannochloropsis oculata] through batch pyrolysis has been investigated. The effect of temperature to the production of energy fuels such as bio-oil, char, and biogas have been simulated considering the yield and energy content as responses. Result of the investigation generally revealed that the proportions of the different biomass did not significantly affect the product yield and energy recovery. Significant effect of temperature is evident in the simulation result of energy recovery whereby maximum conversion was achieved at 400°C for char (91 wt%, 600°C for syngas (22 wt%, and 551°C for bio-oil (48 wt%. Overall energy conversion efficiency of 75.5% was obtained at 589°C in which 15.6 MJ/kg of mixed biomass will be elevated to pyrolysis products.

  14. Energy and Cost Saving of a Photovoltaic-Phase Change Materials (PV-PCM System through Temperature Regulation and Performance Enhancement of Photovoltaics

    Directory of Open Access Journals (Sweden)

    Ahmad Hasan

    2014-03-01

    Full Text Available The current research seeks to maintain high photovoltaic (PV efficiency and increased operating PV life by maintaining them at a lower temperature. Solid-liquid phase change materials (PCM are integrated into PV panels to absorb excess heat by latent heat absorption mechanism and regulate PV temperature. Electrical and thermal energy efficiency analysis of PV-PCM systems is conducted to evaluate their effectiveness in two different climates. Finally costs incurred due to inclusion of PCM into PV system and the resulting benefits are discussed in this paper. The results show that such systems are financially viable in higher temperature and higher solar radiation environment.

  15. Experiment and analysis for a small-sized flywheel energy storage system with a high-temperature superconductor bearing

    Science.gov (United States)

    Kim, Bongsu; Ko, Junseok; Jeong, Sangkwon; Lee, Seung S.

    2006-02-01

    This paper presents a small-sized flywheel energy storage system that uses a high-temperature superconductor (HTS) bearing characterized by a non-contacting bearing with no active control. The small-sized flywheel is made up several magnets for a motor/generator as well as an HTS bearing, and they are fitted into a 34 mm diameter, 3 mm thick aluminium disc. For simplicity and miniaturization of the whole system, the small-sized flywheel takes torque directly from a planar stator, which consists of an axial flux-type brushless DC motor/generator. The small-sized flywheel successfully rotated up to 38 000 rpm in a vacuum while levitated above the stator with a gap of about 1 mm. However, there are some eddy current losses in the stator and non-axisymmetry in the magnetic field causing large drag torque. In order to solve these problems, an improved magnet array in the flywheel, including magnetic screening, is proposed and 3D electromagnetic simulations have been conducted.

  16. Fluoride salts as phase change materials for thermal energy storage in the temperature range 1000-1400 K

    Science.gov (United States)

    Misra, Ajay K.

    1988-01-01

    Eutectic compositions and congruently melting intermediate compounds in binary and ternary fluoride salt systems were characterized for potential use as latent heat of fusion phase change materials to store thermal energy in the temperature range 1000-1400 K. The melting points and eutectic compositions for many systems with published phase diagrams were experimentally verified and new eutectic compositions having melting points between 1000 and 1400 K were identified. Heats of fusion of several binary and ternary eutectics and congruently melting compounds were experimentally measured by differential scanning calorimetry. For a few systems in which heats of mixing in the melts have been measured, heats of fusion of the eutectics were calculated from thermodynamic considerations and good agreement was obtained between the measured and calculated values. Several combinations of salts with high heats of fusion per unit mass (greater than 0.7 kJ/g) have been identified for possible use as phase change materials in advanced solar dynamic space power applications.

  17. Temperature-dependent dielectric and energy-storage properties of Pb(Zr,Sn,Ti)O{sub 3} antiferroelectric bulk ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xuefeng; Liu, Zhen; Xu, Chenhong; Cao, Fei; Wang, Genshui; Dong, Xianlin, E-mail: xldong@mail.sic.ac.cn [Key laboratory of Inorganic Functional Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 200050, Shanghai (China)

    2016-05-15

    The dielectric and energy-storage properties of Pb{sub 0.99}Nb{sub 0.02}[(Zr{sub 0.60}Sn{sub 0.40}){sub 0.95}Ti{sub 0.05}]{sub 0.98}O{sub 3} (PNZST) bulk ceramics near the antiferroelectric (AFE)-ferroelectric (FE) phase boundary are investigated as a function of temperature. Three characteristic temperatures T{sub 0}, T{sub C}, T{sub 2} are obtained from the dielectric temperature spectrum. At different temperature regions (below T{sub 0}, between T{sub 0} and T{sub C}, and above T{sub C}), three types of hysteresis loops are observed as square double loop, slim loop and linear loop, respectively. The switching fields and recoverable energy density all first increase and then decrease with increasing temperature, and reach their peak values at ∼T{sub 0}. These results provide a convenient method to optimize the working temperature of antiferroelectric electronic devices through testing the temperature dependent dielectric properties of antiferroelectric ceramics.

  18. Rotational temperature of N2+ (0,2 ions from spectrographic measurements used to infer the energy of precipitation in different auroral forms and compared with radar measurements

    Directory of Open Access Journals (Sweden)

    D. Lummerzheim

    2008-05-01

    Full Text Available High resolution spectral data are used to estimate neutral temperatures at auroral heights. The data are from the High Throughput Imaging Echelle Spectrograph (HiTIES which forms part of the Spectrographic Imaging Facility (SIF, located at Longyearbyen, Svalbard in Norway. The platform also contains photometers and a narrow angle auroral imager. Quantum molecular spectroscopy is used for modelling N2+ 1NG (0,2, which serves as a diagnostic tool for neutral temperature and emission height variations. The theoretical spectra are convolved with the instrument function and fitted to measured rotational transition lines as a function of temperature. Measurements were made in the magnetic zenith, and along a meridian slit centred on the magnetic zenith. In the results described, the high spectral resolution of the data (0.08 nm allows an error analysis to be performed more thoroughly than previous findings, with particular attention paid to the correct subtraction of background, and to precise wavelength calibration. Supporting measurements were made with the Svalbard Eiscat Radar (ESR. Estimates were made from both optical and radar observations of the average energy of precipitating electrons in different types of aurora. These provide confirmation that the spectral results are in agreement with the variations observed in radar profiles. In rayed aurora the neutral temperature was highest (800 K and the energy lowest (1 keV. In a bright curling arc, the temperature at the lower border was about 550 K, corresponding to energies of 2 keV. The radar and modelling results confirm that these average values are a lower limit for an estimation of the characteristic energy. In each event the energy distribution is clearly made up of more than one spectral shape. This work emphasises the need for high time resolution as well as high spectral resolution. The present work is the first to provide rotational temperatures using a method which pays particular

  19. Electron Attachment to POCl3: Measurement and Theoretical Analysis of Rate Constants and Branching Ratios as a Function of Gas Pressure and Temperature, Electron Temperature, and Electron Energy

    National Research Council Canada - National Science Library

    Van Doren, Jane M; Friedman, Jeffrey F; Miller, Thomas M; Viggiano, A. A; Denifl, S; Scheier, P; Mark, T. D; Troe, J

    2006-01-01

    ... of the resonant POCl3 state and collisional stabilization of the parent anion. In the electron beam experiment at zero electron energy, the fragment ion POCl2- is the dominant ion product of attachment (96...

  20. High Temperature and High Energy Density Dipolar GlassPolymers Based on Sulfonyl Poly(2,6-Dimethyl-1,4-Phenylene (Preprint)

    Science.gov (United States)

    2017-12-06

    AFRL-RX-WP-JA-2017-0520 HIGH TEMPERATURE AND HIGH ENERGY DENSITY DIPOLAR GLASSPOLYMERS BASED ON SULFONYL POLY(2,6-DIMETHYL-1,4... ENERGY DENSITY DIPOLAR GLASSPOLYMERS BASED ON SULFONYL POLY(2,6-DIMETHYL-1,4-PHENYLENE (PREPRINT) 5a. CONTRACT NUMBER FA8650-15-D-5405-0002 5b... energy density reached as high as 22 J·cm-3 at the breakdown field. Due to the high Tg, the SO2-PPO25 sample also exhibited low dielectric losses. For

  1. Energy from Biomass - Comparision of biogas production at ambient temperature and at mesophilic temperature in semicontenous anaerobic digester using vegetable market waste

    Directory of Open Access Journals (Sweden)

    Dhanalakshmi Sridevi V.

    2014-03-01

    Full Text Available Studies are conducted in semicontinuous anaerobic reactors of 2 L Capacity with effective volume of 1.5 L. Experiments were carried out in the mesophilic temperature range maintained at 35°C in a thermostat, and parallel experiments were performed at ambient temperature on biogas production from the month of Februray to August. The reactors were operated with an organic loading rate of 0.5 gVS/L/d with 25 days HRT. The feed stock used for the study was vegetable market waste obtained from Koyambedu vegetable market. The specific biogas production was found to be 0.530 L gVS add-1 for the reactor operated at mesophilic temperature and in the range of 0.431 to 0.732 L gVSadd -1 for the reactor operated in the ambient temperature condition from the month of February to August. The daily biogas production was found to be similar (approximately 350 mL/d when reactors were operated at mesophilic and ambient temperature except for the period of May and June wherein higher amount of daily biogas production (472 and 529 mL/d was observed in the reactor operated at ambient temperature. The ratio of total VFA and alkalinity and propionic acid to acetic acid (PA/AA was found to be in the range of 0.25 – 0.4 and 0.34 - 1.38 during the operation of the reactor for the entire period, which was within the range reported for digester stability.

  2. Energy, economy and exergy evaluations of the solutions for supplying domestic hot water from low-temperature district heating in Denmark

    DEFF Research Database (Denmark)

    Yang, Xiaochen; Li, Hongwei; Svendsen, Svend

    2016-01-01

    . Evaluation models were built to investigate the energy, economy and exergy performances of the proposed domestic hot water systems in various configurations. The configurations of the devised domestic hot water substations were optimised to fit well with both low and ultra-low-temperature district heating...

  3. Impact of aerodynamic resistance formulations used in two-source modeling of energy exchange from the soil and vegetation using land surface temperature

    Science.gov (United States)

    Application of the Two-Source Energy Balance (TSEB) Model using land surface temperature (LST) requires aerodynamic resistance parameterizations for the flux exchange above the canopy layer, within the canopy air space and at the soil/substrate surface. There are a number of aerodynamic resistance f...

  4. The energy release and temperature field in the ultracold neutron source of the WWR-M reactor at the Petersburg Nuclear Physics Institute

    Energy Technology Data Exchange (ETDEWEB)

    Serebrov, A. P., E-mail: serebrov@pnpi.spb.ru; Kislitsin, B. V.; Onegin, M. S.; Lyamkin, V. A.; Prudnikov, D. V.; Ilatovskiy, V. A.; Orlov, S. P.; Kirsanov, G. A.; Fomin, A. K.; Filchenkova, D. V. [National Research Center Kurchatov Institute, Petersburg Nuclear Physics Institute (Russian Federation)

    2016-12-15

    Results of calculations of energy releases and temperature fields in the ultracold neutron source under design at the WWR-M reactor are presented. It is shown that, with the reactor power of 18 MW, the power of energy release in the 40-L volume of the source with superfluid helium will amount to 28.5 W, while 356 W will be released in a liquid-deuterium premoderator. The lead shield between the reactor core and the source reduces the radiative heat release by an order of magnitude. A thermal power of 22 kW is released in it, which is removed by passage of water. The distribution of temperatures in all components of the vacuum structure is presented, and the temperature does not exceed 100°C at full reactor power. The calculations performed make it possible to go to design of the source.

  5. Exploring connections between statistical mechanics and Green's functions for realistic systems: Temperature dependent electronic entropy and internal energy from a self-consistent second-order Green's function

    Science.gov (United States)

    Welden, Alicia Rae; Rusakov, Alexander A.; Zgid, Dominika

    2016-11-01

    Including finite-temperature effects from the electronic degrees of freedom in electronic structure calculations of semiconductors and metals is desired; however, in practice it remains exceedingly difficult when using zero-temperature methods, since these methods require an explicit evaluation of multiple excited states in order to account for any finite-temperature effects. Using a Matsubara Green's function formalism remains a viable alternative, since in this formalism it is easier to include thermal effects and to connect the dynamic quantities such as the self-energy with static thermodynamic quantities such as the Helmholtz energy, entropy, and internal energy. However, despite the promising properties of this formalism, little is known about the multiple solutions of the non-linear equations present in the self-consistent Matsubara formalism and only a few cases involving a full Coulomb Hamiltonian were investigated in the past. Here, to shed some light onto the iterative nature of the Green's function solutions, we self-consistently evaluate the thermodynamic quantities for a one-dimensional (1D) hydrogen solid at various interatomic separations and temperatures using the self-energy approximated to second-order (GF2). At many points in the phase diagram of this system, multiple phases such as a metal and an insulator exist, and we are able to determine the most stable phase from the analysis of Helmholtz energies. Additionally, we show the evolution of the spectrum of 1D boron nitride to demonstrate that GF2 is capable of qualitatively describing the temperature effects influencing the size of the band gap.

  6. 18F-FDG uptake in the colon is modulated by metformin but not associated with core body temperature and energy expenditure.

    Science.gov (United States)

    Bahler, Lonneke; Holleman, Frits; Chan, Man-Wai; Booij, Jan; Hoekstra, Joost B; Verberne, Hein J

    2017-01-01

    Physiological colonic 18F-fluorodeoxyglucose (18F-FDG) uptake is a frequent finding on 18F-FDG positron emission tomography computed tomography (PET-CT). Interestingly, metformin, a glucose lowering drug associated with moderate weight loss, is also associated with an increased colonic 18F-FDG uptake. Consequently, increased colonic glucose use might partly explain the weight losing effect of metformin when this results in an increased energy expenditure and/or core body temperature. Therefore, we aimed to determine whether metformin modifies the metabolic activity of the colon by increasing glucose uptake. In this open label, non-randomized, prospective mechanistic study, we included eight lean and eight overweight males. We measured colonic 18F-FDG uptake on PET-CT, energy expenditure and core body temperature before and after the use of metformin. The maximal colonic 18F-FDG uptake was measured in 5 separate segments (caecum, colon ascendens,-transversum,-descendens and sigmoid). The maximal colonic 18F-FDG uptake increased significantly in all separate segments after the use of metformin. There was no significant difference in energy expenditure or core body temperature after the use of metformin. There was no correlation between maximal colonic 18F-FDG uptake and energy expenditure or core body temperature. Metformin significantly increases colonic 18F-FDG uptake, but this increased uptake is not associated with an increase in energy expenditure or core body temperature. Although the colon might be an important site of the glucose plasma lowering actions of metformin, this mechanism of action does not explain directly any associated weight loss.

  7. 18F-FDG uptake in the colon is modulated by metformin but not associated with core body temperature and energy expenditure.

    Directory of Open Access Journals (Sweden)

    Lonneke Bahler

    Full Text Available Physiological colonic 18F-fluorodeoxyglucose (18F-FDG uptake is a frequent finding on 18F-FDG positron emission tomography computed tomography (PET-CT. Interestingly, metformin, a glucose lowering drug associated with moderate weight loss, is also associated with an increased colonic 18F-FDG uptake. Consequently, increased colonic glucose use might partly explain the weight losing effect of metformin when this results in an increased energy expenditure and/or core body temperature. Therefore, we aimed to determine whether metformin modifies the metabolic activity of the colon by increasing glucose uptake.In this open label, non-randomized, prospective mechanistic study, we included eight lean and eight overweight males. We measured colonic 18F-FDG uptake on PET-CT, energy expenditure and core body temperature before and after the use of metformin. The maximal colonic 18F-FDG uptake was measured in 5 separate segments (caecum, colon ascendens,-transversum,-descendens and sigmoid.The maximal colonic 18F-FDG uptake increased significantly in all separate segments after the use of metformin. There was no significant difference in energy expenditure or core body temperature after the use of metformin. There was no correlation between maximal colonic 18F-FDG uptake and energy expenditure or core body temperature.Metformin significantly increases colonic 18F-FDG uptake, but this increased uptake is not associated with an increase in energy expenditure or core body temperature. Although the colon might be an important site of the glucose plasma lowering actions of metformin, this mechanism of action does not explain directly any associated weight loss.

  8. Exploring connections between statistical mechanics and Green's functions for realistic systems: Temperature dependent electronic entropy and internal energy from a self-consistent second-order Green's function.

    Science.gov (United States)

    Welden, Alicia Rae; Rusakov, Alexander A; Zgid, Dominika

    2016-11-28

    Including finite-temperature effects from the electronic degrees of freedom in electronic structure calculations of semiconductors and metals is desired; however, in practice it remains exceedingly difficult when using zero-temperature methods, since these methods require an explicit evaluation of multiple excited states in order to account for any finite-temperature effects. Using a Matsubara Green's function formalism remains a viable alternative, since in this formalism it is easier to include thermal effects and to connect the dynamic quantities such as the self-energy with static thermodynamic quantities such as the Helmholtz energy, entropy, and internal energy. However, despite the promising properties of this formalism, little is known about the multiple solutions of the non-linear equations present in the self-consistent Matsubara formalism and only a few cases involving a full Coulomb Hamiltonian were investigated in the past. Here, to shed some light onto the iterative nature of the Green's function solutions, we self-consistently evaluate the thermodynamic quantities for a one-dimensional (1D) hydrogen solid at various interatomic separations and temperatures using the self-energy approximated to second-order (GF2). At many points in the phase diagram of this system, multiple phases such as a metal and an insulator exist, and we are able to determine the most stable phase from the analysis of Helmholtz energies. Additionally, we show the evolution of the spectrum of 1D boron nitride to demonstrate that GF2 is capable of qualitatively describing the temperature effects influencing the size of the band gap.

  9. Gibbs free energy of reactions involving SiC, Si3N4, H2, and H2O as a function of temperature and pressure

    Science.gov (United States)

    Isham, M. A.

    1992-01-01

    Silicon carbide and silicon nitride are considered for application as structural materials and coating in advanced propulsion systems including nuclear thermal. Three-dimensional Gibbs free energy were constructed for reactions involving these materials in H2 and H2/H2O. Free energy plots are functions of temperature and pressure. Calculations used the definition of Gibbs free energy where the spontaneity of reactions is calculated as a function of temperature and pressure. Silicon carbide decomposes to Si and CH4 in pure H2 and forms a SiO2 scale in a wet atmosphere. Silicon nitride remains stable under all conditions. There was no apparent difference in reaction thermodynamics between ideal and Van der Waals treatment of gaseous species.

  10. Advanced FeCrAl ODS steels for high-temperature structural applications in energy generation systems

    Directory of Open Access Journals (Sweden)

    Pimentel, G.

    2012-08-01

    Full Text Available Technologies and means for developing biomass plant with higher energy conversion efficiencies are essential in order to implement the commitment to renewable biomass energy generation. Advanced, indirect Combined Cycle Gas Turbine (CCGT systems offer overall biomass energy conversion efficiencies of 45 % and above, compared with the 35 % efficiency of conventional biomass steam plant. However to attain this efficiency in CCGT operation it will be necessary to develop a heat exchanger capable of gas operating temperatures and pressures of around 1100 °C and 15-30 bar, respectively, for entry heating the gas turbine working fluid. ODS ferritic steels is the kind of advance material to deal with this challenge, however work to optimize the coarse grain microstructure to improve creep hoop strength needs to be done. In this sense, this paper reports the recrystallisation behaviour of PM 2000 oxide dispersion strengthened ferritic alloy which was cold deformed after hot-rolling and extrusion. The results can be interpreted if it is assumed that anything which makes the microstructure heterogeneous, stimulates recrystallisation. In this sense, larger strain gradients lead to more refined and more isotropic grain structures. The combination of these results with finite element modeling are used to interpret the role of residual shear stresses on the development of recrystallized grain structure.

    Las tecnologías y medios para desarrollar plantas de biomasa con alta eficiencia en la conversión de energía son esenciales para asentar la biomasa como una fuente de energía renovable. Los sistemas de turbinas de gas de ciclo combinado (CCGT permiten elevar la eficiencia de las plantas de biomasa del 35 % actual al 45 %. Sin embargo, para conseguir estos niveles de eficiencia en la conversión de energía, el intercambiador de calor de la caldera debe trabajar en condiciones extremas de temperatura (por encima de 1100 °C y presión (en torno a 15

  11. Free Energy Minimization Calculation of Complex Chemical Equilibria. Reduction of Silicon Dioxide with Carbon at High Temperature.

    Science.gov (United States)

    Wai, C. M.; Hutchinson, S. G.

    1989-01-01

    Discusses the calculation of free energy in reactions between silicon dioxide and carbon. Describes several computer programs for calculating the free energy minimization and their uses in chemistry classrooms. Lists 16 references. (YP)

  12. Differential calorimeter and temperature controller for stored energy measurements in irradiated alkali halides; Calorimetro diferencial y controlador de temperatura para medidas de energia almacenada en haluros alcalinos irradiados

    Energy Technology Data Exchange (ETDEWEB)

    Delgado Martinez, L.

    1977-07-01

    The design and performance of a simple temperature-controlled differential calorimeter are presented. This system allows to measure radiation-induced stored energy in insulators, above room temperature with a differential thermal analysis method. With platelets of KC1 single crystals, the base lines obtained for T{sub 2} T{sub 1} (with T{sub 2}: irradiated sample temperature and T{sub 1}: reference sample temperature) show a smooth drift less of 0,2 degree centigree in the interval from 25 to 400 degree centigree. The discrepancy between two consecutive base lines is less than {+-} 0,02 degree centigree which implies a calorimeter sensitivity of about {+-}0,004 cal/g. This sensitivity allows to measure stored energy release in samples with a color center concentration low enough to be directly measured with a spectrophotometer so that a search for correlations among the features of the stored energy spectrum and the color center annealing can be made. (Author) 13 refs.

  13. Tissue temperatures attained in indocyanine-green infiltrated and noninfiltrated bovine eyelids using diode laser (805-nm) energy at 3, 5, and 7 watts

    Science.gov (United States)

    Kirkpatrick, John G.; Bartels, Kenneth E.; Dickey, D. Thomas; Powell, Ronald; Schafer, Steven A.; Zhou, Jin Fu; Wicksted, James P.

    1998-07-01

    Normal non-pigmented bovine eyelids in two Hereford cows under general anesthesia were treated with diode laser (805 nm) in a power range of 3 - 6.5 watts. Tissue temperatures were measured in areas infiltrated with 0.25% indocyanine green (ICG) solution and in non-infiltrated areas. Targeted tissue was laser treated at post-injection time intervals of 1 to 60 minutes. Temperatures were measured with a computerized temperature sensing program using hypodermic needle thermistors. Trial objectives were to establish power/chromophore concentration/time parameters to create tumor and peri-tumor tissue temperatures of 50 degrees Celsius without causing epidermal vaporization. Tissue temperature of 50 degrees Celsius has been established as the temperature producing coagulative necrosis of squamous cell carcinoma tumor tissue in 30 seconds. This temperature was produced in chromophore-enhanced tissue bit without repeatable confidence. Bovine ocular squamous cell carcinoma (BOSCC)-affected eyes and eyelids have been successfully treated with carbon dioxide focused and defocused laser with and without chromophore enhanced diode laser (805 nm) energy. The need for tumor staging and procedure standardization requires further investigation to determine laser power/chromophore concentration, and issue exposure times.

  14. Development of Fast and Reliable Free-Energy Density Functional Methods for Simulations of Dense Plasmas from Cold- to Hot-Temperature Regimes

    Science.gov (United States)

    Karasiev, V. V.

    2017-10-01

    Free-energy density functional theory (DFT) is one of the standard tools in high-energy-density physics used to determine the fundamental properties of dense plasmas, especially in cold and warm regimes when quantum effects are essential. DFT is usually implemented via the orbital-dependent Kohn-Sham (KS) procedure. There are two challenges of conventional implementation: (1) KS computational cost becomes prohibitively expensive at high temperatures; and (2) ground-state exchange-correlation (XC) functionals do not take into account the XC thermal effects. This talk will address both challenges and report details of the formal development of new generalized gradient approximation (GGA) XC free-energy functional which bridges low-temperature (ground state) and high-temperature (plasma) limits. Recent progress on development of functionals for orbital-free DFT as a way to address the second challenge will also be discussed. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

  15. Ex Vivo Liver Experiment of Hydrochloric Acid-Infused and Saline-Infused Monopolar Radiofrequency Ablation: Better Outcomes in Temperature, Energy, and Coagulation.

    Science.gov (United States)

    Jiang, Xiong-ying; Gu, Yang-kui; Huang, Jin-hua; Gao, Fei; Zou, Ru-hai; Zhang, Tian-qi

    2016-04-01

    To compare temperature, energy, and coagulation between hydrochloric acid-infused radiofrequency ablation (HAIRFA) and normal saline-infused radiofrequency ablation (NSIRFA) in ex vivo porcine liver model. 30 fresh porcine livers were excised in 60 lesions, 30 with HAIRFA and the other 30 with NSIRFA. Both modalities used monopolar perfusion electrode connected to a RF generator set at 103 °C and 30 W. In each group, ablation time was set at 10, 20, or 30 min (10 lesions from each group at each time). We compared tissue temperatures (at 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 cm away from the electrode tip), average power, deposited energy, deposited energy per coagulation volume (DEV), coagulation diameters, coagulative volume, and spherical ratio between the two groups. Temperature-time curves showed that HAIRFA provided progressively greater heating than that of NSIRFA. At 30 min, mean average power, deposited energy, coagulation volumes (113.67 vs. 12.28 cm(3)) and diameters, and increasing in tissue temperature were much greater with HAIRFA (P < 0.001 for all), except DEV was lower (456 vs. 1396 J/cm(3), P < 0.001). The spherical ratio was closer to 1 with HAIRFA (1.23 vs. 1.46). Coagulation diameters, volume, and average power of HAIRFA increased significantly with longer ablation times. While with NSIRFA, these characteristics were stable till later 20 min, except the power decreased with longer ablation times. HAIRFA creates much larger and more spherical lesions by increasing overall energy deposition, modulating thermal conductivity, and transferring heat during ablation.

  16. Temperature and chain length dependence of ultrafast vibrational dynamics of thiocyanate in alkylimidazolium ionic liquids: A random walk on a rugged energy landscape

    Science.gov (United States)

    Brinzer, Thomas; Garrett-Roe, Sean

    2017-11-01

    Ultrafast two-dimensional infrared spectroscopy of a thiocyanate vibrational probe (SCN-) was used to investigate local dynamics in alkylimidazolium bis-[trifluoromethylsulfonyl]imide ionic liquids ([Imn,1][Tf2N], n = 2, 4, 6) at temperatures from 5 to 80 °C. The rate of frequency fluctuations reported by SCN- increases with increasing temperature and decreasing alkyl chain length. Temperature-dependent correlation times scale proportionally to temperature-dependent bulk viscosities of each ionic liquid studied. A multimode Brownian oscillator model demonstrates that very low frequency (modes primarily drive the observed spectral diffusion and that these modes broaden and blue shift on average with increasing temperature. An Arrhenius analysis shows activation barriers for local motions around the probe between 5.5 and 6.5 kcal/mol that are very similar to those for translational diffusion of ions. [Im6,1][Tf2N] shows an unexpected decrease in activation energy compared to [Im4,1][Tf2N] that may be related to mesoscopically ordered polar and nonpolar domains. A model of dynamics on a rugged potential energy landscape provides a unifying description of the observed Arrhenius behavior and the Brownian oscillator model of the low frequency modes.

  17. Standardization of the temperature of the drier of agricultural products using biomass energy; Padronizacao da temperatura de um secador de produtos agropecuarios utilizando energia de biomassa

    Energy Technology Data Exchange (ETDEWEB)

    Bernardino, Cassiano Augusto Rolim; Valenca, David da Cunha [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Seropedica, RJ (Brazil); Amorim, Elizete [Universidade Federal Rural do Rio de Janeiro (UFRRJ), Seropedica, RJ (Brazil). Curso de Ciencia e Tecnologia de Alimentos; Barbosa Junior, Jose Lucena; Silva, Pedro Paulo de Oliveira [Universidade Federal Rural do Rio de Janeiro (DTA/IT/UFRRJ), Seropedica, RJ (Brazil). Inst. de Tecnologia. Dept. de Tecnologia de Alimentos

    2010-07-01

    The aim of this work was to study the influence of the mass and dimensions of wood (length and diameter) on the temperature variation in a drying system for agricultural products which use energy from the combustion of wood. In this system, the heat generated from burning wood is transferred by heat exchangers to a certain amount of water in a closed circuit, which returns the heat to the drying air (0,074 m{sup 3}.s{sup -1}). It was found that the addition to each hour of two pieces of 4,5 cm in diameter, 35 cm in length and the total weight of 1066 g, provided temperatures from 40,6 to 48,3 deg C in different positions of the dryer. When using three pieces of the same dimensions and mass of 1720 g, the temperature range obtained was from 77,6 to 80,2 deg C. The averages over all experiments had coefficients of variation below 5%, ensuring a drying system with controlled temperature from the energy obtained from combustion of biomass. The results showed the existence of a relationship between the amount of wood added and the temperature in the drier ant that the equipment can be used to obtain standardized dried products on small farms. (author)

  18. Effects of Temperature on First-Excited-State Energy of the Strong Coupling Magnetopolaron in 2D RbCl Parabolic Quantum Dots

    Science.gov (United States)

    Cai, Chun-Yu; Zhao, Cui-Lan; Xiao, Jing-Lin

    2015-02-01

    We study the effects of external fields that are present in nanostructures and can trap particles and manipulate their quantum states. To obtain the effects of temperature on the strong coupling magnetopolaron's first-excited-state energy (FESE) and transition frequency (TF), we use the Lee-Low-Pines unitary transformation (LLPUT) and linear combination operation (LCO) methods. Numerical results, performed in the 2D RbCl parabolic quantum dot (QD), show that the magnetopolaron's FESE and TF (MFESETF) increase with increasing the effective confinement strength and cyclotron frequency (CF) of the magnetic field and temperature.

  19. Estimation of the relationship between growth, consumption, and energy allocation in juvenile pacific cod (Gadus macrocephalus) as a function of temperature and ration

    Science.gov (United States)

    Sreenivasan, Ashwin; Heintz, Ron

    2016-10-01

    Pacific cod (Gadus macrocephalus) are generalist predators in the Gulf of Alaska (GOA), and are an important predator on other commercially important species. Efficient management of this species can benefit by knowing how these fish adapt to changing environmental conditions, with a focus on how growth and condition are affected by changes in temperature and diet. We conducted a feeding study to understand the relationship between growth, ration, and temperature, and how these factors interact to affect energy allocation strategies. Since growth and condition of juveniles can determine recruitment into the population, this study focused on growth and consumption of age 1+Pacific cod held over 4 temperature treatments (4 °C, 8 °C, 12 °C, and 16 °C) and 3 ration levels (unlimited ration, medium ration, and low ration). We also compared cellular nucleic acid (RNA/DNA) ratios, an instantaneous growth index, total-body lipid, and proximate composition between fish. At 4 °C, 8 °C, and 12 °C, fish at medium and low rations had higher growth rates relative to fish at high rations. Higher food consumption appears to negatively affect digestive ability, assimilation efficiency, and nutrient utilization. RNA/DNA was clearly correlated with growth rates at 4 °C and 8 °C, but this relationship did not hold at higher temperatures. A secondary growth study was conducted to test the reliability of the growth/consumption models derived from the main growth study. Temperature influenced energy reserves (lipid) while tissue growth (protein) was influenced by ration level. Average lipid values were higher at 4 °C than at 8 °C or 12 °C, suggesting a predisposition to heightened lipid synthesis at colder temperatures. Longer durations of warmer water temperature in the GOA could consequently affect energy allocation strategies, with dietary changes in the field potentially amplifying this effect in cold and warm years. This energy allocation strategy could be detrimental

  20. Energy conservation in high-rise buildings: changes in air conditioning load induced by vertical temperature and humidity profile in Delhi

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, S. [Institute of Social Forestry and Eco-rehabilitation, ICFRE, Allahabad (India); Kumar, Sanjay [Indian Inst. of Technology, Centre for Atmospheric Sciences, New Delhi (India); Kumar, N. [MIT, Civil Engineering Dept., Bihar (India)

    1998-12-31

    Temperature and humidity profiles in the upper atmosphere are different from those observed by ground level meteorological stations and used to design HVAC systems for high-rise buildings. There exist correlations among solar energy, atmospheric turbidity and pollutants in urban areas, affecting the temperature and humidity profiles with variation in height. In the present study, a theoretical model is developed considering these parameters, and the HVAC load is calculated. The results are compared with the HVAC load calculated from data obtained from the meteorological station, and the comparison showed that the results differ significantly (20%) for a hypothetical 200 m high office building. (Author)

  1. Polarization dependence of the electroabsorption in low-temperature grown GaAs for above band-gap energies

    DEFF Research Database (Denmark)

    Ruff, M.; Streb, D.; Dankowski, S. U.

    1996-01-01

    We have measured the electroabsorption in low-temperature grown GaAs by performing room-temperature transmission experiments in the spectral range from 1.3 to 1.9 eV for different electric fields induced by a voltage applied to a metal-semiconductor-metal structure. The devices were separated fro...

  2. Thermal annealing of high dose radiation induced damage at room temperature in alkaline. Stored energy, thermoluminescence and coloration; Aniquilacion termica de dano inducido por irradiacion a altas dosis en haluros alcalinos a 300 k. energia almacenda. Termoluminiscencia y coloracion

    Energy Technology Data Exchange (ETDEWEB)

    Delgado, L.

    1980-07-01

    The possible relation between stored energy, thermoluminescence and colour centre annealing in gamma and electron irradiated alkali halides is studied. Thermoluminescence occurs at temperature higher than the temperature at which the main stored energy peak appears. No stored energy release is detected in additively coloured KC1 samples. Plastic deformation and doping with Ca and Sr induce a stored energy spectrum different from the spectrum observed in pure and as cleaved samples, but the amount of stored energy does not change for a given irradiation dose.Capacity of alkali halides to store energy by irradiation increases as the cation size decreases. (Author) 51 refs.

  3. Effect of holding equine oocytes in meiosis inhibitor-free medium before in vitro maturation and of holding temperature on meiotic suppression and mitochondrial energy/redox potential.

    Science.gov (United States)

    Martino, Nicola A; Dell'Aquila, Maria E; Filioli Uranio, Manuel; Rutigliano, Lucia; Nicassio, Michele; Lacalandra, Giovanni M; Hinrichs, Katrin

    2014-10-11

    Evaluation of mitochondrial function offers an alternative to evaluate embryo development for assessment of oocyte viability, but little information is available on the relationship between mitochondrial and chromatin status in equine oocytes. We evaluated these parameters in immature equine oocytes either fixed immediately (IMM) or held overnight in an Earle's/Hank's' M199-based medium in the absence of meiotic inhibitors (EH treatment), and in mature oocytes. We hypothesized that EH holding may affect mitochondrial function and that holding temperature may affect the efficiency of meiotic suppression. Experiment 1 - Equine oocytes processed immediately or held in EH at uncontrolled temperature (22 to 27°C) were evaluated for initial chromatin configuration, in vitro maturation (IVM) rates and mitochondrial energy/redox potential. Experiment 2 - We then investigated the effect of holding temperature (25°C, 30°C, 38°C) on initial chromatin status of held oocytes, and subsequently repeated mitochondrial energy/redox assessment of oocytes held at 25°C vs. immediately-evaluated controls. EH holding at uncontrolled temperature was associated with advancement of germinal vesicle (GV) chromatin condensation and with meiotic resumption, as well as a lower maturation rate after IVM. Holding did not have a significant effect on mitochondrial distribution within chromatin configurations. Independent of treatment, oocytes having condensed chromatin had a significantly higher proportion of perinuclear/pericortical mitochondrial distribution than did other GV configurations. Holding did not detrimentally affect oocyte energy/redox parameters in viable GV-stage oocytes. There were no significant differences in chromatin configuration between oocytes held at 25°C and controls, whereas holding at higher temperature was associated with meiosis resumption and loss of oocytes having the condensed chromatin GV configuration. Holding at 25°C was not associated with progression

  4. Mechanical energy losses in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Zelada, Griselda I. [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Lambri, Osvaldo Agustin [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Instituto de Fisica Rosario - CONICET, Member of the CONICET& #x27; s Research Staff, Avda. Pellegrini 250, 2000 Rosario (Argentina); Bozzano, Patricia B. [Laboratorio de Microscopia Electronica, Unidad de Actividad Materiales, Centro Atomico Constituyentes, Comision Nacional de Energia Atomica, Avda. Gral. Paz 1499, 1650 San Martin (Argentina); Garcia, Jose Angel [Departamento de Fisica Aplicada II, Facultad de Ciencias y Tecnologia, Universidad del Pais Vasco, Apdo. 644, 48080 Bilbao, Pais Vasco (Spain)

    2012-10-15

    Mechanical spectroscopy (MS) and transmission electron microscopy (TEM) studies have been performed in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum, oriented for single slip, in order to study the dislocation dynamics in the temperature range within one third of the melting temperature. A damping peak related to the interaction of dislocation lines with both prismatic loops and tangles of dislocations was found. The peak temperature ranges between 900 and 1050 K, for an oscillating frequency of about 1 Hz. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. System analysis of central receiver concepts with high temperature thermal energy storages: Receiver technologies and storage cycles

    Science.gov (United States)

    Steiner, Peter; Schwaiger, Karl; Haider, Markus; Walter, Heimo

    2017-06-01

    Reducing the levelized cost of electricity for solar thermal electricity (STE) plants is the most important challenge of this technology. A bottleneck at state of the art STE plants is the heat storage medium (HSM) with its temperature limits. To replace the commonly used molten salt, particles like quartz sand or corundum, enabling temperatures up to 1000 °C, are proposed as new HSM. The temperature raise leads to economical challenges, which have to be analyzed more in detail. In this work two STE plant concepts based on particles as HSM are introduced and discussed to outline advantages and issues concerning this technology.

  6. Impact of long-term moderate hypercapnia and elevated temperature on the energy budget of isolated gills of Atlantic cod (Gadus morhua).

    Science.gov (United States)

    Kreiss, Cornelia M; Michael, Katharina; Bock, Christian; Lucassen, Magnus; Pörtner, Hans-O

    2015-04-01

    Effects of severe hypercapnia have been extensively studied in marine fishes, while knowledge on the impacts of moderately elevated CO2 levels and their combination with warming is scarce. Here we investigate ion regulation mechanisms and energy budget in gills from Atlantic cod acclimated long-term to elevated PCO2 levels (2500 μatm) and temperature (18°C). Isolated perfused gill preparations were established to determine gill thermal plasticity during acute exposures (10-22°C) and in vivo costs of Na(+)/K(+)-ATPase activity, protein and RNA synthesis. Maximum enzyme capacities of F1Fo-ATPase, H(+)-ATPase and Na(+)/K(+)-ATPase were measured in vitro in crude gill homogenates. After whole animal acclimation to elevated PCO2 and/or warming, branchial oxygen consumption responded more strongly to acute temperature change. The fractions of gill respiration allocated to protein and RNA synthesis remained unchanged. In gills of fish CO2-exposed at both temperatures, energy turnover associated with Na(+)/K(+)-ATPase activity was reduced by 30% below rates of control fish. This contrasted in vitro capacities of Na(+)/K(+)-ATPase, which remained unchanged under elevated CO2 at 10°C, and earlier studies which had found a strong upregulation under severe hypercapnia. F1Fo-ATPase capacities increased in hypercapnic gills at both temperatures, whereas Na(+)/K(+)ATPase and H(+)-ATPase capacities only increased in response to elevated CO2 and warming indicating the absence of thermal compensation under CO2. We conclude that in vivo ion regulatory energy demand is lowered under moderately elevated CO2 levels despite the stronger thermal response of total gill respiration and the upregulation of F1Fo-ATPase. This effect is maintained at elevated temperature. Copyright © 2014 Elsevier Inc. All rights reserved.

  7. Temperature dependence of internal motions of protein side-chain NH3(+) groups: insight into energy barriers for transient breakage of hydrogen bonds.

    Science.gov (United States)

    Zandarashvili, Levani; Iwahara, Junji

    2015-01-20

    Although charged side chains play important roles in protein function, their dynamic properties are not well understood. Nuclear magnetic resonance methods for investigating the dynamics of lysine side-chain NH3(+) groups were established recently. Using this methodology, we have studied the temperature dependence of the internal motions of the lysine side-chain NH3(+) groups that form ion pairs with DNA phosphate groups in the HoxD9 homeodomain-DNA complex. For these NH3(+) groups, we determined order parameters and correlation times for bond rotations and reorientations at 15, 22, 28, and 35 °C. The order parameters were found to be virtually constant in this temperature range. In contrast, the bond-rotation correlation times of the NH3(+) groups were found to depend strongly on temperature. On the basis of transition state theory, the energy barriers for NH3(+) rotations were analyzed and compared to those for CH3 rotations. Enthalpies of activation for NH3(+) rotations were found to be significantly higher than those for CH3 rotations, which can be attributed to the requirement of hydrogen bond breakage. However, entropies of activation substantially reduce the overall free energies of activation for NH3(+) rotations to a level comparable to those for CH3 rotations. This entropic reduction in energy barriers may accelerate molecular processes requiring hydrogen bond breakage and play a kinetically important role in protein function.

  8. Temperature dependence of the optical energy gap in CdS sub x Se sub 1 sub - sub x quantum dots

    CERN Document Server

    Kunets, V P; Kunets, V P; Lisitsa, M P; Malysh, N I

    2002-01-01

    The temperature dependence of the optical energy gap E sub g (T) in CdS sub x Se sub 1 sub - sub x quantum dots synthesized in a borosilicate glass matrix has been investigated in the range of 4.2-500 K. A dependence similar to that for bulk crystals is observed for dots with r-bar > a sub B (r-bar being an average radius of the dot and a sub B the Bohr exciton radius in the bulk), which is described by Varshni formula within the whole temperature range. Deviations from the Varshni dependence in the range 4.2-100 K and smaller band-gap temperature coefficient are observed for dots with r-bar < a sub B. These results are explained in terms of the decrease of the macroscopic electron-phonon interaction potential and the modification of the vibration spectrum peculiar to the dot volume shrinkage

  9. Energy-Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Elevated Temperature Aluminum Metal Matrix Composite (MMC) Alloy and Its Processing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, David C. [Eck Industreis, Inc.; Gegal, Gerald A.

    2014-04-15

    The objective of this project was to provide a production capable cast aluminum metal matrix composite (MMC) alloy with an operating temperature capability of 250-300°C. Important industrial sectors as well as the military now seek lightweight aluminum alloy castings that can operate in temperature ranges of 250-300°C. Current needs in this temperature range are being satisfied by the use of titanium alloy castings. These have the desired strength properties but the end components are heavier and significantly more costly. Also, the energy requirements for production of titanium alloy castings are significantly higher than those required for production of aluminum alloys and aluminum alloy castings.

  10. Effects of High Energy Electron Irradiation on a Yttrium Barium(2) Copper(3) Oxygen(7-delta) High Temperature Superconductor

    Science.gov (United States)

    1991-09-01

    expulsion of magnetic fields from the interior of a superconductor such that B = 0 and is the phenome- non that explains magnetic levitation . From Ohm’s Law...2Cu 30 7 - HIGH TEMPERATURE SUPERCONDUCTOR by Sean Mark Connors September 1991 Thesis Advisor: X. K. Maruyama Approved for public release...if necessary and identify by btock numbe,) FiE GP<P ,€ 5 pCOO HIGH TEMPERATURE SUPERCONDUCTORS , IRRADIATION EFFECTS, ELECTRON IRRADIATION

  11. Temperature, but not available energy, affects the expression of a sexually selected ultraviolet (UV colour trait in male European green lizards.

    Directory of Open Access Journals (Sweden)

    Katalin Bajer

    Full Text Available BACKGROUND: Colour signals are widely used in intraspecific communication and often linked to individual fitness. The development of some pigment-based (e.g. carotenoids colours is often environment-dependent and costly for the signaller, however, for structural colours (e.g. ultraviolet [UV] this topic is poorly understood, especially in terrestrial ectothermic vertebrates. METHODOLOGY/PRINCIPAL FINDINGS: In a factorial experiment, we studied how available energy and time at elevated body temperature affects the annual expression of the nuptial throat colour patch in male European green lizards (Lacerta viridis after hibernation and before mating season. In this species, there is a female preference for males with high throat UV reflectance, and males with high UV reflectance are more likely to win fights. We found that (i while food shortage decreased lizards' body condition, it did not affect colour development, and (ii the available time for maintaining high body temperature affected the development of UV colour without affecting body condition or other colour traits. CONCLUSIONS/SIGNIFICANCE: Our results demonstrate that the expression of a sexually selected structural colour signal depends on the time at elevated body temperature affecting physiological performance but not on available energy gained from food per se in an ectothermic vertebrate. We suggest that the effect of high ambient temperature on UV colour in male L. viridis makes it an honest signal, because success in acquiring thermally favourable territories and/or effective behavioural thermoregulation can both be linked to individual quality.

  12. Temperature, but not available energy, affects the expression of a sexually selected ultraviolet (UV) colour trait in male European green lizards.

    Science.gov (United States)

    Bajer, Katalin; Molnár, Orsolya; Török, János; Herczeg, Gábor

    2012-01-01

    Colour signals are widely used in intraspecific communication and often linked to individual fitness. The development of some pigment-based (e.g. carotenoids) colours is often environment-dependent and costly for the signaller, however, for structural colours (e.g. ultraviolet [UV]) this topic is poorly understood, especially in terrestrial ectothermic vertebrates. In a factorial experiment, we studied how available energy and time at elevated body temperature affects the annual expression of the nuptial throat colour patch in male European green lizards (Lacerta viridis) after hibernation and before mating season. In this species, there is a female preference for males with high throat UV reflectance, and males with high UV reflectance are more likely to win fights. We found that (i) while food shortage decreased lizards' body condition, it did not affect colour development, and (ii) the available time for maintaining high body temperature affected the development of UV colour without affecting body condition or other colour traits. Our results demonstrate that the expression of a sexually selected structural colour signal depends on the time at elevated body temperature affecting physiological performance but not on available energy gained from food per se in an ectothermic vertebrate. We suggest that the effect of high ambient temperature on UV colour in male L. viridis makes it an honest signal, because success in acquiring thermally favourable territories and/or effective behavioural thermoregulation can both be linked to individual quality.

  13. Temperature-induced impacts on groundwater quality and arsenic mobility in anoxic aquifer sediments used for both drinking water and shallow geothermal energy production.

    Science.gov (United States)

    Bonte, Matthijs; van Breukelen, Boris M; Stuyfzand, Pieter J

    2013-09-15

    Aquifers used for the production of drinking water are increasingly being used for the generation of shallow geothermal energy. This causes temperature perturbations far beyond the natural variations in aquifers and the effects of these temperature variations on groundwater quality, in particular trace elements, have not been investigated. Here, we report the results of column experiments to assess the impacts of temperature variations (5°C, 11°C, 25°C and 60°C) on groundwater quality in anoxic reactive unconsolidated sandy sediments derived from an aquifer system widely used for drinking water production in the Netherlands. Our results showed that at 5 °C no effects on water quality were observed compared to the reference of 11°C (in situ temperature). At 25°C, As concentrations were significantly increased and at 60 °C, significant increases were observed pH and DOC, P, K, Si, As, Mo, V, B, and F concentrations. These elements should therefore be considered for water quality monitoring programs of shallow geothermal energy projects. No consistent temperature effects were observed on Na, Ca, Mg, Sr, Fe, Mn, Al, Ba, Co, Cu, Ni, Pb, Zn, Eu, Ho, Sb, Sc, Yb, Ga, La, and Th concentrations, all of which were present in the sediment. The temperature-induced chemical effects were probably caused by (incongruent) dissolution of silicate minerals (K and Si), desorption from, and potentially reductive dissolution of, iron oxides (As, B, Mo, V, and possibly P and DOC), and mineralisation of sedimentary organic matter (DOC and P). Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. WHATCH'EM: A Weather-Driven Energy Balance Model for Determining Water Height and Temperature in Container Habitats for Aedes aegypti.

    Science.gov (United States)

    Steinhoff, Daniel F; Monaghan, Andrew J; Eisen, Lars; Barlage, Michael J; Hopson, Thomas M; Tarakidzwa, Isaac; Ortiz-Rosario, Karielys; Lozano-Fuentes, Saul; Hayden, Mary H; Bieringer, Paul E; Welsh Rodríguez, Carlos M

    2016-12-01

    The mosquito virus vector Aedes (Ae.) aegypti exploits a wide range of containers as sites for egg laying and development of the immature life stages, yet the approaches for modeling meteorologically sensitive container water dynamics have been limited. This study introduces the Water Height and Temperature in Container Habitats Energy Model (WHATCH'EM), a state-of-the-science, physically based energy balance model of water height and temperature in containers that may serve as development sites for mosquitoes. The authors employ WHATCH'EM to model container water dynamics in three cities along a climatic gradient in México ranging from sea level, where Ae. aegypti is highly abundant, to ~2100 m, where Ae. aegypti is rarely found. When compared with measurements from a 1-month field experiment in two of these cities during summer 2013, WHATCH'EM realistically simulates the daily mean and range of water temperature for a variety of containers. To examine container dynamics for an entire season, WHATCH'EM is also driven with field-derived meteorological data from May to September 2011 and evaluated for three commonly encountered container types. WHATCH'EM simulates the highly nonlinear manner in which air temperature, humidity, rainfall, clouds, and container characteristics (shape, size, and color) determine water temperature and height. Sunlight exposure, modulated by clouds and shading from nearby objects, plays a first-order role. In general, simulated water temperatures are higher for containers that are larger, darker, and receive more sunlight. WHATCH'EM simulations will be helpful in understanding the limiting meteorological and container-related factors for proliferation of Ae. aegypti and may be useful for informing weather-driven early warning systems for viruses transmitted by Ae. aegypti.

  15. Effect of the surface temperature on surface morphology, deuterium retention and erosion of EUROFER steel exposed to low-energy, high-flux deuterium plasma

    Directory of Open Access Journals (Sweden)

    M. Balden

    2017-08-01

    Full Text Available Samples of EUFROFER, a reduced activation ferritic martensitic steel, were exposed in the linear plasma device Pilot-PSI to a deuterium (D plasma with incident ion energy of ∼40eV and incident D flux of 2–6×1023D/m2s to fluences up to 1027D/m2 at surface temperatures ranging from 400K to 950K. The main focus of the study lays on the surface morphology changes dependent on the surface temperature and the surface composition evolution, e.g., the enrichment in tungsten; but also the erosion and the D retention are studied. The created surface morphology varies strongly with surface temperature from needle-like to corral-like structures. The visible lateral length scale of the formed structures is in the range of tens of nanometres to above 1µm and exhibits two thermal activated regimes below and above ∼770K with activation energies of 0.2eV and 1.3eV, respectively. The lateral variation of the enrichment of heavy elements on the surface is correlated to this surface morphology at least in the high temperature regime, independent of the origin of the enrichment (intrinsic from the sample or deposited by the plasma. Also the erosion exhibits temperature dependence at least above ∼770K as well as a fluence dependence. The amount of deuterium retained in the top 500nm is almost independent of the exposure temperature and is of the order of 1018D/m2, which would correspond to a sub-monolayer D coverage on the surface. The retained D in the volume summing up over the complete samples exceeds the D retained close to the surface by one order of magnitude.

  16. Quantum state-resolved molecular scattering of NO (2Π1/2 at the gas-[Cnmim][Tf2N] room temperature ionic liquid interface: Dependence on alkyl chain length, collision energy, and temperature

    Directory of Open Access Journals (Sweden)

    Amelia Zutz

    2016-10-01

    Full Text Available Room temperature ionic liquids (RTILs represent a promising class of chemically tunable, low vapor pressure solvents with myriad kinetic applications that depend sensitively on the nature of gas-molecule interactions at the liquid surface. This paper reports on rovibronically inelastic dynamics at the gas-RTIL interface, colliding supersonically cooled hyperthermal molecular beams of NO (Π1/22, N = 0 from 1-alkyl-3-methylimidazolium bis(trifluoromethylsulfonylimide (or [Cnmim][Tf2N] and probing the scattered NO molecules via laser induced fluorescence (LIF from the A(2Σ state. Specifically, inelastic energy transfer into NO rovibrational and electronic degrees of freedom is explored as a function of RTIL alkyl chain length (n, incident collision energy (Einc and surface temperature (Ts. At low collision energies (Einc = 2.7(9 kcal/mol, the scattered NO molecules exhibit a rotational temperature (Trot systematically colder than Ts for all chain lengths, which signals the presence of non-equilibrium dynamics in the desorption channel. At high collision energies (Einc = 20(2 kcal/mol, microscopic branching into trapping/desorption (TD and impulsive scattering (IS pathways is clearly evident, with the TD fraction (α exhibiting a step-like increase between short (n = 2, 4 and long (n = 8, 12, 16 alkyl chains consistent with theoretical predictions. For all hydrocarbon chain lengths and RTIL temperature conditions, NO rotational excitation in the IS channel yields hyperthermal albeit Boltzmann-like distributions well described by a “temperature” (TIS = 900 -1200 K that decreases systematically with increasing n. Non-adiabatic, collision induced hopping between ground and excited spin-orbit states is found to be independent of RTIL alkyl chain length and yet increase with collision energy. The scattering data confirm previous experimental reports of an enhanced presence of the alkyl tail at the gas-RTIL interface with increasing n, as well as

  17. The interaction of C60 on Si(111 7x7 studied by Supersonic Molecular Beams: interplay between precursor kinetic energy and substrate temperature in surface activated processes.

    Directory of Open Access Journals (Sweden)

    Lucrezia eAversa

    2015-06-01

    Full Text Available Buckminsterfullerene (C60 is a molecule fully formed of carbon that can be used, owing to its electronic and mechanical properties, as clean precursor for the growth of carbon-based materials, ranging from -conjugated systems (graphenes to synthesized species, e.g. carbides such as silicon carbide (SiC. To this goal, C60 cage rupture is the main physical process that triggers material growth. Cage breaking can be obtained either thermally by heating up the substrate to high temperatures (630°C, after C60 physisorption, or kinetically by using Supersonic Molecular Beam Epitaxy (SuMBE techniques. In this work, aiming at demonstrating the growth of SiC thin films by C60 supersonic beams, we present the experimental investigation of C60 impacts on Si(111 7x7 kept at 500°C for translational kinetic energies ranging from 18 to 30 eV. The attained kinetically activated synthesis of SiC submonolayer films is probed by in-situ surface electron spectroscopies (XPS and UPS. Furthermore, in these experimental conditions the C60-Si(111 7×7 collision has been studied by computer simulations based on a tight-binding approximation to Density Functional Theory, DFT. Our theoretical and experimental findings point towards a kinetically driven growth of SiC on Si, where C60 precursor kinetic energy plays a crucial role, while temperature is relevant only after cage rupture to enhance Si and carbon reactivity. In particular, we observe a counterintuitive effect in which for low kinetic energy (below 22 eV, C60 bounces back without breaking more effectively at high temperature due to energy transfer from excited phonons. At higher kinetic energy (22 < K < 30 eV, for which cage rupture occurs, temperature enhances reactivity without playing a major role in the cage break. These results are in good agreement with ab-initio molecular dynamics simulations. SuMBE is thus a technique able to drive materials growth at low temperature regime.

  18. X-ray response of CdZnTe detectors grown by the vertical Bridgman technique: Energy, temperature and high flux effects

    Science.gov (United States)

    Abbene, L.; Gerardi, G.; Turturici, A. A.; Raso, G.; Benassi, G.; Bettelli, M.; Zambelli, N.; Zappettini, A.; Principato, F.

    2016-11-01

    Nowadays, CdZnTe (CZT) is one of the key materials for the development of room temperature X-ray and gamma ray detectors and great efforts have been made on both the device and the crystal growth technologies. In this work, we present the results of spectroscopic investigations on new boron oxide encapsulated vertical Bridgman (B-VB) grown CZT detectors, recently developed at IMEM-CNR Parma, Italy. Several detectors, with the same electrode layout (gold electroless contacts) and different thicknesses (1 and 2.5 mm), were realized: the cathode is a planar electrode covering the detector surface (4.1×4.1 mm2), while the anode is a central electrode (2×2 mm2) surrounded by a guard-ring electrode. The detectors are characterized by electron mobility-lifetime product (μeτe) values ranging between 0.6 and 1·10-3 cm2/V and by low leakage currents at room temperature and at high bias voltages (38 nA/cm2 at 10000 V/cm). The spectroscopic response of the detectors to monochromatic X-ray and gamma ray sources (109Cd, 241Am and 57Co), at different temperatures and fluxes (up to 1 Mcps), was measured taking into account the mitigation of the effects of incomplete charge collection, pile-up and high flux radiation induced polarization phenomena. A custom-designed digital readout electronics, developed at DiFC of University of Palermo (Italy), able to perform a fine pulse shape and height analysis even at high fluxes, was used. At low rates (200 cps) and at room temperature (T=25 °C), the detectors exhibit an energy resolution FWHM around 4% at 59.5 keV, for comparison an energy resolution of 3% was measured with Al/CdTe/Pt detectors by using the same electronics (A250F/NF charge sensitive preamplifier, Amptek, USA; nominal ENC of 100 electrons RMS). At high rates (750 kcps), energy resolution values of 7% and 9% were measured, with throughputs of 2% and 60% respectively. No radiation polarization phenomena were observed at room temperature up to 1 Mcps (241Am source, 60 ke

  19. Energy-effective method for low-temperature deaeration of make-up water on the heating supply system of heat power plants

    Science.gov (United States)

    Sharapov, V. I.; Pazushkina, O. V.; Kudryavtseva, E. V.

    2016-01-01

    The technology for low-temperature deaeration of make-up water of heating supply systems is developed that makes it possible to substantially enhance the energy efficiency of heat power plants (HPPs). As a desorbing agent for deaeration of make-up water of heating supply systems, it is proposed to use not steam or superheated water but a gas supplied to boiler burners. Natural gas supplied to steam boilers of HPPs has very low or often negative temperature after reducing devices. At the same time, it is virtually corrosive gas-free (oxygen and carbon dioxide) and, therefore, can be successfully used as the desorbing agent for water deaeration. These factors make it possible to perform deaeration of make-up water of heating supply systems at relatively low temperatures (10-30°C). Mixing of the cold deaerated make-up water with the return delivery water results in a significant decrease in the temperature the return delivery water before a lower delivery heater of a dual-purpose turbine plant, increase in the power output with the heat consumption, and, consequently, enhancement in the operation efficiency of the HPP. The article presents the calculation of the consumption of gas theoretically required for deaeration and reveals the evaluation of the energy efficiency of the technology for a typical energy unit of thermal power station. The mass transfer efficiency of the deaeration of the make-up water of heating supply systems is estimated for the case of using natural gas as the desorbing agent for which the specific gas consumption required theoretically for deaeration is calculated. It is shown that the consumption of natural gas used as fuel in boilers of HPPs is sufficient for the deaeration of any volumes of the make-up water of heating supply systems. The energy efficiency of the developed technology is evaluated for a typical heat power-generating unit of the HPP with a T-100-12.8 turbine. The calculation showed that the application of the new technology

  20. Simulation of energy use, human thermal comfort and office work performance in buildings with moderately drifting operative temperatures

    DEFF Research Database (Denmark)

    Kolarik, Jakub; Toftum, Jørn; Olesen, Bjarne W.

    2011-01-01

    ) supplemented with CAV ventilation. Simulations comprised moderate, hot–dry and hot–humid climate. Heavy and light wall construction and two orientations of the building (east–west and north–south) were considered. Besides the energy use, also capability of examined systems to keep a certain level of thermal......Annual primary energy use in a central module of an office building consisting of two offices separated with a corridor was estimated by means of dynamic computer simulations. The simulations were conducted for conventional all-air VAV ventilation system and thermo active building system (TABS...... comfort was examined. The results showed that with the moderate climate, the TABS decreased the primary energy use by about 16% as compared with the VAV. With hot–humid climate, the portion of the primary energy saved by TABS was ca. 50% even with the supply air dehumidification taken into account...

  1. Low temperature geothermal energy applications in the Albuquerque area. Final report, July 1, 1978-August 18, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Kauffman, D.; Houghton, A.V.

    1979-01-01

    A study was made of the engineering and economic feasibility of hot water geothermal energy applications in the Albuquerque area. A generalized system design was developed and used as the basis for a series of economic case studies. Reservoir and user siting considerations were studied in light of the economic findings. Several specific potential applications were identified, including university campuses, industrial and commercial facilities, and residential buildings. Specific key technical problems relating to Albuquerque area applications were studied. These included environmental impacts, corrosion, scaling, heat losses in wells and transmission lines, heat exchangers, control systems, and system utilization and reliability. It is concluded that geothermal energy could be competitive with other energy sources for space heating and limited industrial use for moderate to large (10 million Btu/hr or more) energy using systems.

  2. Solar Energy.

    Science.gov (United States)

    Eaton, William W.

    Presented is the utilization of solar radiation as an energy resource principally for the production of electricity. Included are discussions of solar thermal conversion, photovoltic conversion, wind energy, and energy from ocean temperature differences. Future solar energy plans, the role of solar energy in plant and fossil fuel production, and…

  3. Energy loss and surface temperature effects in ab initio molecular dynamics simulations: N adsorption on Ag(111) as a case study

    Science.gov (United States)

    Novko, Dino; Lončarić, Ivor; Blanco-Rey, María; Juaristi, J. Iñaki; Alducin, Maite

    2017-08-01

    We study surface temperature effects on the adsorption and relaxation of N atoms on Ag(111). To this aim, we perform ab initio molecular dynamics simulations with electronic friction, in which the surface is coupled to a thermostat that fixes the desired surface temperature. Simulations performed at 80 and 700 K show that the surface temperature has minor effects on magnitudes such as the initial adsorption probability, the relaxation rate of the adsorbing N, and the energy lost in electronic excitations. Slight differences are identified in the adsorption paths with the appearance of subsurface absorption events at 700 K that are not observed at 80 K. Furthermore, we perform additional simulations without a thermostat in order to examine the validity of commonly used ab initio molecular dynamics simulations in which no heat dissipation from the simulation cell is allowed. Our results show that such a methodology may not suffice to simulate the low-temperature regime since the surface becomes unphysically heated within a few picoseconds upon adsorption of the N atom. However, neither in this unfavorable case are the magnitudes defining the dynamics of the adsorbates at the same time scale significantly modified from those obtained at constant surface temperature.

  4. Energy conservation in forcing bulb flowers by means of temperature integration; Energiebesparing bij de broeierij van bolbloemen door temperatuurintegratie

    Energy Technology Data Exchange (ETDEWEB)

    Gude, H.; Dijkema, M.H.G.E.

    2006-03-15

    The options of Temperature Integration (TI) have been described for application in heating tulips, hyacinths and daffodils. The tolerance levels of the crops for increasing the day temperature and lowering the night temperature has been examined. In the first year, tests were conducted under fully conditioned circumstances in climate cabinets; in the second year tests were done in cabinets and greenhouses; in the third year only in the greenhouse. The tests are described in chronological order per crop [Dutch] De mogelijkheden van Temperatuur Integratie (TI) zijn beschreven voor toepassing in de broeierij van tulp, hyacint en narcis. De tolerantie van de gewassen voor verhogingen van de dagtemperatuur en verlagingen van de nachttemperatuur is vastgesteld. In het eerste jaar zijn de proeven onder volledig geconditioneerde omstandigheden in klimaatkasten uitgevoerd, in het tweede jaar in klimaatkasten en kas en in het derde jaar alleen in de kas. De proeven worden chronologisch per gewas beschreven.

  5. Embedded fiber Bragg grating sensors for true temperature monitoring in Nb$_3$Sn superconducting magnets for high energy physics

    CERN Document Server

    Chiuchiolo, A; Bajko, M; Consales, M; Giordano, M; Perez, J C; Cusano, A

    2016-01-01

    The luminosity upgrade of the Large Hadron Collider (HL-LHC) planned at the European Organization for Nuclear Research (CERN) requires the development of a new generation of superconducting magnets based on Nb3Sn technology. The instrumentation required for the racetrack coils needs the development of reliable sensing systems able to monitor the magnet thermo-mechanical behavior during its service life, from the coil fabrication to the magnet operation. With this purpose, Fiber Bragg Grating (FBG) sensors have been embedded in the coils of the Short Model Coil (SMC) magnet fabricated at CERN. The FBG sensitivity to both temperature and strain required the development of a solution able to separate mechanical and temperature effects. This work presents for the first time a feasibility study devoted to the implementation of an embedded FBG sensor for the measurement of the "true" temperature in the impregnated Nb3Sn coil during the fabrication process. © (2016) COPYRIGHT Society of Photo-Optical Instrumentatio...

  6. Prediction of weld data using process control based on surface temperature measurement for high-power energy flow processes

    Science.gov (United States)

    Brueggemann, Gunnar; Benziger, Thomas

    1996-09-01

    The main aim of this article is to obtain the correlation between the thermal cycle and the mechanical properties in the weld seam and the heat-affected zone of mild and stainless steels. Key targeted process is welding using electron beam, laser and plasma. Since these processes are characterized by high heating and cooling rates, wide temperature range, small heat affected zones, they are difficult to control and automize. As a consequence, the quality of the product varies over a large range. Because either temperature measurement on one spot or quasi steady- state surface temperature distribution in a large area are generally unsuitable, temperature gradients need to be controlled directly on-line with a high accuracy. This requires the use of a two dimensional temperature control. An infrared camera systems can be used in order to investigate the cooling process in the weld seam area as well as in the heat affected zone. On the one hand the aim of the experiments is the estimation of the microstructure, especially of the hardness distribution using welding-time- temperature-conversion-diagrams and equations of regression. On the other hand the observation of the cooling cycle allows trends of mechanical diagrams and equations of regression. On the other hand the observation of the cooing cycle allows trends of mechanical properties like stretch limit, tensile strength, breaking elongation to be predicted. Simultaneously it is possible to recognize and to localize pores, voids and bonding defects, losses in penetration, problems with gap and height, appearing during the cooling of the weld.

  7. Energy harvesting through gas dynamics in the free molecular flow regime between structured surfaces at different temperatures

    DEFF Research Database (Denmark)

    Baier, Tobias; Dölger, Julia; Hardt, Steffen

    2014-01-01

    For a gas confined between surfaces held at different temperatures the velocity distribution shows a significant deviation from the Maxwell distribution when the mean free path of the molecules is comparable to or larger than the channel dimensions. If one of the surfaces is suitably structured......, this nonequilibrium distribution can be exploited for momentum transfer in a tangential direction between the two surfaces. This opens up the possibility to extract work from the system which operates as a heat engine. Since both surfaces are held at constant temperatures, the mode of momentum transfer is different...

  8. An energy stable evolution method for simulating two-phase equilibria of multi-component fluids at constant moles, volume and temperature

    KAUST Repository

    Kou, Jisheng

    2016-02-25

    In this paper, we propose an energy-stable evolution method for the calculation of the phase equilibria under given volume, temperature, and moles (VT-flash). An evolution model for describing the dynamics of two-phase fluid system is based on Fick’s law of diffusion for multi-component fluids and the Peng-Robinson equation of state. The mobility is obtained from diffusion coefficients by relating the gradient of chemical potential to the gradient of molar density. The evolution equation for moles of each component is derived using the discretization of diffusion equations, while the volume evolution equation is constructed based on the mechanical mechanism and the Peng-Robinson equation of state. It is proven that the proposed evolution system can well model the VT-flash problem, and moreover, it possesses the property of total energy decay. By using the Euler time scheme to discretize this evolution system, we develop an energy stable algorithm with an adaptive choice strategy of time steps, which allows us to calculate the suitable time step size to guarantee the physical properties of moles and volumes, including positivity, maximum limits, and correct definition of the Helmhotz free energy function. The proposed evolution method is also proven to be energy-stable under the proposed time step choice. Numerical examples are tested to demonstrate efficiency and robustness of the proposed method.

  9. Thermodynamic description of the Al-Mg-Si system using a new formulation for the temperature dependence