Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

International Nuclear Information System (INIS)

Pietrucha, K.; Pekala, W.; Kroh, J.

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with 60 Co γ-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed. (author)

Radiation induced graft copolymerization of methyl methacrylate onto chrome-tanned pig skins

Energy Technology Data Exchange (ETDEWEB)

Pietrucha, K.; Pekala, W.; Kroh, J. (Lodz Univ. (Poland))

1981-01-01

Graft copolymerization of methyl methacrylate (MMA) onto chrome-tanned pig skins was carried out by irradiation with /sup 60/Co ..gamma..-rays. The grafted polymethyl methacrylate (PMMA) chains were isolated by acid hydrolysis of the collagen backbone in order to characterize the graft copolymers. Proof of grafting was obtained through the detection of amino acid endgroups in the isolated grafts by reaction with ninhydrin. The grafting yield of MMA in aqueous emulsion was found to be higher than that for pure MMA and MMA in acetone. The degree of grafting increases with increasing monomer concentration in emulsion and reaches maximum at radiation dose ca 15 kGy. The yield of grafting is very high. The present paper reports the physical properties of chrome-tanned pig skins after graft polymerization with MMA in emulsion. Modified leathers are more resistant against water absorption and abrasion in comparison with unmodified ones. They have more uniform structure over the whole surface, greater thickness and stiffness. The mechanism of some of the processes occurring during radiation grafting of MMA in water emulsion on tanned leathers has been also suggested and discussed.

Monodispersepoly[BMA-co-(COPS-I)] Particles by Soap-Free Emulsion Copolymerization and Its Optical Properties as Photonic Crystals.

Science.gov (United States)

Lee, Ki Chang; Choo, Hun Seung

2015-10-01

In order to study the surfactant-free emulsion copolymerization of benzyl methacrylate (BMA) with sodium 1-allyloxy-2-hydroxypropane sulfonate (COPS-I) and the resulting optical properties, a series of experiments was carried out at various reaction conditions such as the changes of BMA concentration, COPS-I concentration, BMA concentration under a fixed COPS-I amount, initiator and divinyl benzene (DVB) concentration. All the latices showed highly monodispersed spherical particles in the size range of 144~435 nm and the respective shiny structural colors from their colloidal photonic crystals. It is found that the changes in such polymerization factors greatly affect the number of particles and particle diameter, polymerization rate, molecular weight, zeta-potential, and refractive indices. The increase of number of particles led to the increased rate of polymerization and zeta-potential of the latices, on the other hand, to the decreased molecular weight. Refractive indices and the reflectivity increased with COPS-I concentration, on the other hand, and decreased with DVB concentration. Especially, refractive indices of the resulting poly[BMA-co-(COPS-I)] colloidal photonic crystals showed much higher values of 1.65~2.21 than that of polystyrene, due to the formation of core-shell shaped morphology. Monodisperse and high refractive index of poly[BMA-co-(COPS-I)] particles prepared in this work could be used for the study in photonic crystals and electrophoretic display.

The influence of emulsion structure on the Maillard reaction of ghee.

Science.gov (United States)

Newton, Angela E; Fairbanks, Antony J; Golding, Matt; Andrewes, Paul; Gerrard, Juliet A

2015-04-15

Food systems, such as cream and butter, have an emulsion or emulsion-like structure. When these food emulsions are heated to high temperatures to make products such as ghee, the Maillard reaction forms a range of volatile flavour compounds. The objective of this paper was to unravel the specific influence of emulsion structure on the Maillard reaction pathways that occur during the cooking of ghee using model systems. Switching the dispersed phase from oil to water provided a means of altering the ratios of volatile compounds produced in the cooked samples. The oil-in-water emulsion generated a volatile compound profile similar to that of the fat containing two phase model matrix, whereas the water-in-oil emulsion produced a different ratio of these compounds. The ability to generate different volatile compound profiles through the use of inverted emulsion structures could point to a new avenue for control of the Maillard reaction in high temperature food systems. Copyright © 2014 Elsevier Ltd. All rights reserved.

Kinetics of waterborne fluoropolymers prepared by one-step semi-continuous emulsion polymerization of chlorotrifluoroethylene, vinyl acetate, butyl acrylate and Veova 10

Science.gov (United States)

Liu, H. Z.; Wang, M. H.; Wang, Z. F.; Bian, J. M.

2018-01-01

Due to using gaseous fluorine monomer with toxicity, waterborne fluoropolymers are synthesized by semi-continuous high-pressure emulsion polymerization method which differs from free-pressure emulsion polymerization. To dates, the research on preparing process and kinetics for high-pressure emulsion polymerization is reported relatively less, which hinders researchers from understanding of mechanisms for monomer-fluorinated emulsion polymerization. The paper also provides a new method by element auxiliary analysis to calculate kinetics parameters of high-pressure emulsion polymerization. Based on aforementioned consideration, waterborne fluoropolymers were prepared by copolymerization of chlorotrifluoroethylene (CTFE), vinyl acetate (VAc), butyl acrylate (BA) and vinyl ester of versatic acid (Veova 10) using potassium persulfate as initiator and mixed surfactants. The kinetics of emulsion polymerization of waterborne fluoropolymers was then investigated. Effects of emulsifier concentration, initiator concentration, and polymerization temperature on polymerization rate (Rp) were evaluated, and relationship was described as Rp∝[I]0.10 and Rp∝[E]0.12. The apparent activation energy was determined to be 33.61 kJ·mol-1. Moreover, the relative conversion rate of CTFE with the other monomers was observed, and results indicated that CTFE monomer more uniformly copolymerized with the other monomers. The resulting emulsion properties and pressure change in an autoclave were evaluated at different stirring rates. The initial reaction time, defined as the beginning time of dropwise addition, was determined by the change in solid content and particle size of emulsion.

Mathematical Simulation of High-Conversion Binary Copolymerization

Institute of Scientific and Technical Information of China (English)

JiangWei; QinJiguang

2005-01-01

A new model for mathematical simulation of high-conversion binary copolymerization was established by combination of the concept of the three stage polymerization model (TSPM) proposed by Qin et al. for bulk free radical homopolymerization with the North equation to describe high-conversion copolymerization reaction exhibiting a strong gel effect, and the mathematical expressions of this new model were derived. Like TSPM, the new model also assmnes that the whole course of binary copolymerization can be divided into three different stages: low conversion, gel effect and glass effect stages. In addition, the reaction rate constants and the initiator efficiency at each copolymerization stage do not vary with conversion. Based on the expressions derived, a plot method for determining the overall rate constants and critical conversions was proposed. The literature data on conversion history for styrene (St)-methyl methacrylate (MMA) and ethylene glycol dimethacrylate (EGDMA)-MMA copolymerizations were treated to examine the model, which shows that the model is satisfactory.

Rheological Behavior of Reaction Mixtures during the Graft Copolymerization of Cassava Starch with Acrylic Acid

NARCIS (Netherlands)

Witono, J.R.; Noordergraaf, Inge; Heeres, Hero; Janssen, L.P.B.M.

2017-01-01

Literature data on the rheological behavior of a reaction mixture during the graft copolymerization of acrylic acid onto gelatinized starch are scarce. Yet, such information is important for process design. In this work, continuous torque recording was found to be a suitable method to monitor the

Heavy ion and hadron reactions in emulsion

International Nuclear Information System (INIS)

Otterlund, I.

1979-04-01

Recent results from heavy ion and hadron reactions in emulsion are reviewed. General properties of hadron-reaction multiplicities and their correlation to the production of recoiling protons are given. Properties of pseudo-rapidity distributions of shower-particles especially the particle production in the central region of pseudo-rapidity will be discussed. Non-peripheral heavy ion reactions are compared to recent participant-spectator model calculations. Very energetic cosmic ray events will be examined in the light of recent results from hadron-nucleus reactions. (author)

Radiation-induced emulsion copolymerization of tetrafluoroethylene with propylene in flow system, 8

International Nuclear Information System (INIS)

Watanabe, Hiromasa; Ito, Masayuki; Machi, Sueo; Okamoto, Jiro.

1982-02-01

Seeded copolymerization of tetrafluoroethylene with propylene by radiation was carried out in a flow apparatus with pipe reactor at a pressure of 30 kg/cm 2 , a temperature of 40 0 C, a propylene fraction in monomer gas of 0.1, and at various dose rates. Amounts of dissolved monomer in latex increases in proportion to the polymer concentration, however, it becomes lower than that in equilibrium as polymerization proceeds. Propylene fraction in the dissolved monomer decreases with reaction time. Polymer concentration in latex increases accelerately with reaction time, and polymerization rate increases and tends to level off when the polymer concentration exceeds 100 g/l-H 2 O at higher dose rate. Polymerization rate is proportional to the 0.6 power of the dose rate at the polymer concentration of 50 g/l-H 2 O, and the power factor decreases from 0.46 to 0.39 with increasing the concentration from 100 to 150 g/l-H 2 O. Molecular weight of the polymer is proportional to the -0.17 power of the dose rate. The dose rate effects are explained by considering both first-order termination by degradative chain transfer to propylene and second-order termination by recombination. (author)

Radiation crosslinking of poly(butyl acrylate) during polymerization and grafted copolymerization with Cr(III) crosslinked collagen

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1984-01-01

Enhanced crosslinking of synthetic polymer simultaneous with grafting and homopolymerization processes have been observed in irradiated leather tanned with Cr(III) and embedded with aqueous emulsions of butyl acrylate. Extent of poly(butyl acrylate) crosslinking during copolymerization was found to be approximately one order higher than in the case of radiation polymerization of butyl acrylate in emulsion. New method for isolation of grafted copolymer based on degradation of collagen has been developed. The extent of crosslinking was calculated from the swelling data. (author)

Radiation crosslinking of poly(butyl acrylate) during polymerization and grafted copolymerization with Cr(III) crosslinked collagen

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1986-01-01

Enhanced crosslinking of synthetic polymer simultaneously with grafting and homopolymerization processes has been observed in irradiated leather tanned with Cr(III) and embedded with aqueous emulsions of butyl acrylate. The extent of poly(butyl acrylate) crosslinking during copolymerization was found to be approximately one order higher than in the case of radiation polymerization of butyl acrylate in emulsion. A new method for isolation of grafted copolymer based on degradation of collagen has been developed. The extent of crosslinking was calculated from the swelling data. (author)

Selective absorption of water from different oil–water emulsions with ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 30; Issue 4. Selective absorption of water from different oil–water emulsions with Psy-cl-poly(AAm) synthesized using irradiation copolymerization method. B S Kaith Kiran Kumar. Polymers Volume 30 Issue 4 August 2007 pp 387-391 ...

Pickering interfacial catalysis for biphasic systems: from emulsion design to green reactions.

Science.gov (United States)

Pera-Titus, Marc; Leclercq, Loïc; Clacens, Jean-Marc; De Campo, Floryan; Nardello-Rataj, Véronique

2015-02-09

Pickering emulsions are surfactant-free dispersions of two immiscible fluids that are kinetically stabilized by colloidal particles. For ecological reasons, these systems have undergone a resurgence of interest to mitigate the use of synthetic surfactants and solvents. Moreover, the use of colloidal particles as stabilizers provides emulsions with original properties compared to surfactant-stabilized emulsions, microemulsions, and micellar systems. Despite these specific advantages, the application of Pickering emulsions to catalysis has been rarely explored. This Minireview describes very recent examples of hybrid and composite amphiphilic materials for the design of interfacial catalysts in Pickering emulsions with special emphasis on their assets and challenges for industrially relevant biphasic reactions in fine chemistry, biofuel upgrading, and depollution. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Improvement in Wood Bonding Strength of Poly (Vinyl Acetate-Butyl Acrylate Emulsion by Controlling the Amount of Redox Initiator

Directory of Open Access Journals (Sweden)

Yun Zhang

2018-01-01

Full Text Available Polyvinyl acetate emulsion adhesive has been widely used due to its good bonding performance and environmentally friendly properties. Indeed, the bonding performance can be further improved by copolymerizing with other monomers. In this study, the effect of the adjunction of redox initiator (hydrogen peroxide–tartaric acid, H2O2–TA on the properties of the poly (vinyl acetate-butyl acrylate (P (VAc–BA emulsion adhesive was investigated. With increasing dosage, the reaction became more complete and the obtained film was more compact, as identified via SEM. The core-shell structure of the emulsion particles was confirmed via TEM. Results indicate that while the initiator content increased from 0.5 to 1.0%, a clearer core-shell structure was obtained and the bonding strength of the plywood improved from 2.34 to 2.97 MPa. With the further incorporation of H2O2–TA (i.e., 1.5%, the bonding performance deteriorated. The optimum wood bonding strength (2.97 MPa of the prepared P (VAc-BA emulsion adhesive was even better than that (2.55 MPa of a commercial PVAc emulsion adhesive, suggesting its potential application for the wood industry.

Radiation copolymerization of tributyltin methacrylate and methylmathacrylate

International Nuclear Information System (INIS)

Zhao Binxi; Zhu Xiaohong; Murat; Han Zhewen

1987-01-01

The copolymer of tributytin methacrylate and methylmethacrylate is a useful self-polishing antifouling paints materials. It was synthesized by radiation polymerization using 60 Co γ ray at room temperature. The copolymerization kinetics of the pair of monomers was studied. The relationship between the reaction rate and the dose rate was found to be R p = K p ·I -053 and the reactivity ratios were measured to be less than 1. The overall activition energy was 1.29 x 10 4 J/mol. It was supposed that the copolymerization was of radical machanism

Monitoring emulsion homopolymerization reactions using FT-Raman spectroscopy

Directory of Open Access Journals (Sweden)

M. M. Reis

2005-03-01

Full Text Available The present work describes a methodology for estimation of monomer concentration during homopolymerization reactions by Raman spectroscopy. The estimation is done using linear models based on two different approaches: a univariate approach and a multivariate approach (with principal component regression, PCR, or partial least squares regression, PLS. The linear models are fitted with data from spectra collected from synthetic samples, i.e., samples prepared by dispersing a known concentration of monomer in polymer emulsions. Homopolymerizations of butyl acrylate and of vinyl acetate were monitored by collecting samples from the reactor, and results show that the methodology is efficient for the model fitting and that Raman spectroscopy is a promising technique for on-line monitoring of the emulsion polymerization process.

EFFECTS OF ω-ACRYLOYL POLY(ETHYLENE OXIDE) MACROMONOMER ON EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE AND n-BUTYL ACRYLATE

Institute of Scientific and Technical Information of China (English)

无

1998-01-01

Well-defined nonionic hydrophilic ω-acryloyl poly(ethylene oxide) macromonomer (PEO-A) has been prepared by living anionic polymerization of ethylene oxide with diphenyl methyl potassium as the initiator and acryloyl chloride as the reaction terminating agent. The polymer was characterized by FTIR and SEC. The emulsifier-free emulsion polymerization of methyl methacrylate (MMA) and n-butyl acrylate (BA) containing various concentrations of PEO-A was studied. In all cases stable emulsion coplymerizations of MMA and BA were obtained. The stabilizing effect was found to be dependent on the molecular weight and the feed amount of the macromonomer.

Enhancing both the mechanical and chemical properties of paper sheet by graft co-polymerization with acrylonitrile/methyl methacrylate

Directory of Open Access Journals (Sweden)

H.M. Abd El Salam

2014-09-01

Full Text Available The chemical graft copolymerization reaction of acrylonitrile (AN and methyl methacrylate (MMA binary mixture onto paper sheet was performed. The effect of initiator concentration, monomer concentration and temperature on the reaction rate was studied. The reaction rate equation of the graft copolymerization reaction is found to be RP = K2 [Initiator]0.795[Monomer]2.007. The apparent activation energy (Ea of the copolymerization reaction is found to be 75.01 kJ/mol. The infrared characteristic absorption bands for cellulosic paper structure and the paper gr-AN-MMA are investigated. Tensile break load, porosity and burst strength were measured for the grafted and pure paper sheet. It was found that the mechanical properties are improved by grafting copolymerization. The chemical resistance of the graft product against a strong acid a strong alkali, polar and nonpolar solvents was investigated. It was found that the resistance to these chemicals is enhanced by grafting.

Copolymerization of Carbon–carbon Double-bond Monomer (Styrene with Cyclic Monomer (Tetrahydrofuran

Directory of Open Access Journals (Sweden)

Sari Fouad

2012-12-01

Full Text Available We reported in this work that the cationic copolymerization in one step takes place between carbon–carbon double-bond monomer styrene with cyclic monomer tetrahydrofuran. The comonomers studied belong to different families: vinylic and cyclic ether. The reaction is initiated with maghnite-H+ an acid exchanged montmorillonite as acid solid ecocatalyst. Maghnite-H+ is already used as catalyst for polymerization of many vinylic and heterocyclic monomers. The oxonium ion of tetrahydrofuran and carbonium ion of styrene propagated the reaction of copolymerization. The acetic anhydride is essential for the maintenance of the ring opening of tetrahydrofuran and the entry in copolymerization. The temperature was kept constant at 40°C in oil bath heating for 6 hours. A typical reaction product was analyzed by 1H-NMR, 13C-NMR and IR and the formation of the copolymer was confirmed. The reaction was proved by matched with analysis. The maghnite-H+ allowed us to obtain extremely pure copolymer in good yield by following a simples operational conditions. Copyright © 2012 by BCREC UNDIP. All rights reservedReceived: 29th October 2012; Revised: 29th November 2012; Accepted: 29th November 2012[How to Cite: S. Fouad, M.I. Ferrahi, M. Belbachir. (2012. Copolymerization of Carbon–carbon Double-bond Monomer (Styrene with Cyclic Monomer (Tetrahydrofuran. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 165-171. (doi:10.9767/bcrec.7.2.4074.165-171][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.4074.165-171 ] | View in 

The Free-Radical Copolymerization of Difurylmethane with Maleic

African Journals Online (AJOL)

Prof. Jo Michael

Reaction feeds containing 85 mol % and higher of difurylmethane ... Keywords: difurylmethane; maleic anhydride; copolymerization; thermodecomposition ... delivery apparatus set at 500 psi for a flow rate of 1 cm3 min-1; a Waters model U6K.

Graft-copolymerization of styrene on polypropylene in the solid phase

NARCIS (Netherlands)

Beenen, W.; VanderWal, D.; Janssen, L.P.B.M.; Buijtenhuijs, A.; Hogt, A.H.; Wal, Douwe J. v.d.

The graft-copolymerization of styrene on PP in the solid phase has been studied under various reaction conditions using a radical initiator. Polymerization kinetics were investigated by DSC experiments and reactions in glass ampoules. The conversion rate and grafting efficiency of styrene appeared

Radiation-induced emulsion copolymerization of tetrafluoroethylene with propylene in flow system, (9)

International Nuclear Information System (INIS)

Watanabe, Hiromasa; Ito, Masayuki; Okamoto, Jiro; Machi, Sueo.

1982-02-01

Seeded copolymerization of tetrafluoroethylene with propylene by radiation was carried out in a flow apparatus with pipe reactor at a pressure of 30 kg/cm 2 , a temperature of 40 0 C, a dose rate of 4.9 x 10 5 rad/h, and at various monomer compositions. Polymer concentration in latex increases linearly at propylene fraction of 0.25 and accelerately at the fraction below 0.1 with reaction time. The polymerization rates are 36, 60, 57, and 46 g/h.l-H 2 O at propylene fractions of 0.01, 0.05, 0.1, and 0.25, respectively. Fluorine content of the polymer obtained at the end of polymerization is 53.8 wt% at propylene fractions of 0.25 and 0.1, and is 56.5 wt% at the fraction of 0.01. For the insoluble polymer in tetrahydrofuran produced at the fraction of 0.01, the fluorine content is 61.3 wt%. This indicates that monomer unit ratio of tetrafluoroethylene and propylene is 1.8/l. In the polymerization at a region of high tetrafluoroethylene content in monomer gas, it was elucidated that alternative arrangement of copolymer being characteristic in this system is broken down to produce tetrafluoroethylene rich polymer, and polymerization rate is reduced. This is explained by that addition of propylene monomer to tetrafluoroethylene polymer radical becomes rate-determining step due to the extremely poor propylene concentration in polymer particles. (author)

Co-polymerization of methyl methacrylate and styrene via surfactant-free emulsion polymerization, as a potential material for photonic crystal application

Science.gov (United States)

Kassim, Syara; Zahari, Siti Balqis; Tahrin, Rabiatul Addawiyah Azwa; Harun, Noor Aniza

2017-09-01

Photonic crystals are being the great interest of researcher to studies due to a variety of potential application for the interaction of light including the solar cells, optical sensors and paints. In order to evaluate the fabrication of photonic crystals thin film, a free-emulsifier emulsion copolymerization of styrene and methyl methacrylate was carried out. By using the self -assembly approach, this method offers the opportunity to produce crystalline polymer sphere in more ease operation, low cost and environmental friendly. The influences of the mixing ratio of monomer and amount of initiators were studied. In advance, the presence of styrene as co-monomer had improved the thermal degradation of polymer methyl methacrylate. While in changing the mixing ratio of styrene and methyl methacrylate resulted in particle size of the sphere. The size of polymer particles slightly increased on increasing volume of styrene monomer ratio. This occurred because the properties of styrene in water where it sparingly soluble and lead to coagulation of particles. This simple, yet effective method for preparing functional complex 3D structures has the potential to be used generically to fabricate a variety of functional porous 3D structures that could find application not only in new or improved photonic crystal (PC) devices but also in areas such as catalysis, solar cell, separation, fuel cells technology, microelectronics and optoelectronics.

Emulsion Polymerization of Tung Oil-Based Latexes with Asolectin as a Biorenewable Surfactant

Directory of Open Access Journals (Sweden)

Ashley Johns

2016-11-01

Full Text Available Bio-based vesicles, with potential application in drug delivery and/or catalyst encapsulation, have been prepared by the free radical emulsion co-polymerization of tung oil, divinylbenzene (DVB, n-butyl methacrylate (BMA, and asolectin in a xylene/water mixture. The free radical polymerization was initiated by di-tert-butyl peroxide (DTBP at 100 °C in a convection oven. Molecular weights of approximately 11,000 Da were measured by Matrix-assisted Laser Desorption/Ionization-Time of Flight (Maldi-TOF for tung oil-asolectin copolymers, verifying that significant polymerization occurs under the cure conditions employed. The cure of the co-monomer mixture employed in this work was monitored by Dielectric Analysis (DEA, while changes in the Raman spectrum of all co-monomers before and after the cure, along with differential scanning calorimetry (DSC analysis, have been used to verify the need of a post-cure step and completion of the polymerization reaction. Scanning Transmission Electron Microscopy (STEM images of the emulsion after polymerization indicate that vesicles were formed, and vesicle size distribution of samples prepared with different amounts of tung oil were determined using a Zetasizer.

Preparation and Properties of Triethoxyvinylsilane-Modified Styrene - Butyl Acrylate Emulsion Copolymers

OpenAIRE

NAGHASH, Hamid Javaherian; KARIMZADEH, Akram; MOMENI, Ahmad Reza; MASSAH, Ahmad Reza; ALIAN, Hamid

2014-01-01

The copolymers of triethoxyvinylsilane (TEVS) with styrene (St), butyl acrylate (BA), and methacrylic acid (MAA) were prepared by emulsion polymerization. The copolymerization was carried out by using auxiliary agents at 90 °C in the presence of potassium peroxodisulfate (KPS) as the initiator. Nonylphenol ethylene oxide -- 40 units (NP-40) and sodium lauryl sulfoacetate (SLSA) were used as nonionic and anionic emulsifiers, respectively. The resulting copolymers were characterized b...

Influences of Electrolytes on the Soap-free Emulsion Copolymerization of St-MMA-AA

Institute of Scientific and Technical Information of China (English)

Rong Long LI; Cheng You KAN; Yi DU; Ze Ping LI

2006-01-01

Monodisperse functional polymer microspheres with different particle size and with clean surface were prepared by batch soap-free emulsion polymerization of styrene, methyl methacrylate and acrylic acid in the presence of salts, and the influences of type and amount of electrolytes on polymerization process and particle morphology were investigated. Results showed that there was a critical concentration for different electrolyte to make polymerization process and the resultant emulsion stable, and the particle size increased with the increase of electrolyte concentration. The effect of metal ions was Ca2+＞＞K+＞Na+＞Li+, and the effect of haloids was Br-＞Cl-＞F-.

Vinyl Chloride Emulsion Polymerization Reaction: Effect of Various Formulations

Directory of Open Access Journals (Sweden)

Seyed Mehrdad Jalilian

2013-01-01

Full Text Available A mixture  of  sodium  lauryl  sulfate  (SLS  as  ionic  emulsifer  and  stearyl alcohol as non-ionic emulsifer was employed in a vinyl chloride emulsion polymerization  reaction  to  study  the  infuence  of  various  interactive parameters involved in the reaction system. It was found that the particle size was dependent on the amount and type of emulsifer. The average particle size of polyvinyl chloride was dropped by higher amount of emulsifying agents.  At the gel point, more heat was generated by higher amount of vinyl chloride fed into the reaction system. The molecular weight of the polymer was decreased by increases in reaction temperature while,  it  increased by augmenting  the amount of emulsifer. According to the 13C NMR and FTIR spectroscopic data no defect was detected in the chain structure of synthetic polyvinylchloride product. An optimization of polymerization reaction condition was reached based on ultimate particle size desired for its favorable distribution in plastisols.

Olefin copolymerization via controlled radical polymerization : copolymerization of methyl methacrylate and 1-octene

NARCIS (Netherlands)

Venkatesh, R.; Klumperman, B.

2004-01-01

The atom transfer radical (co)polymerization (ATRP) of methyl methacrylate (MMA) with 1-octene was investigated. Well controlled homopolymer of MMA was obtained with 2,2,2-trichoroethanol (TCE) and p-toluenesulfonyl chloride (pTsCl), although, uncontrolled copolymerization occurred when pTsCl was

A RARE CASE OF AZEOTROPIC COPOLYMERIZATION

NARCIS (Netherlands)

JONGSMA, T; KIMKES, P; CHALLA, G

1991-01-01

Copolymerizations with both reactivity ratios equal to one are rare. Therefore, we report here on the radical copolymerization of styrene and p-tert-butoxy-carbonyl-oxy-styrene in toluene with AIBN as initiator. We found it to be an azeotropic copolymerization for all compositions, i.e. f1 = F1 and

Chain-growth cycloaddition polymerization via a catalytic alkyne [2 + 2 + 2] cyclotrimerization reaction and its application to one-shot spontaneous block copolymerization.

Science.gov (United States)

Sugiyama, Yu-ki; Kato, Rei; Sakurada, Tetsuya; Okamoto, Sentaro

2011-06-29

A cobalt-catalyzed alkyne [2 + 2 + 2] cycloaddition reaction has been applied to polymerizations yielding linear polymers via selective cross-cyclotrimerization of yne-diyne monomers, which occurs in a chain-growth manner. Additionally, through control of the alkyne reactivity of the two monomers, this method was efficiently applied to the spontaneous block copolymerization of their mixture. Here we present the proposed mechanism of the catalyst transfer process of this cycloaddition polymerization.

Copolymerization parameters of N-Methacryloyloxy tetrabromophthalimide with different vinyl monomers

International Nuclear Information System (INIS)

Mahmoud, A.A.

2005-01-01

N-Methacryloyloxytetrabromophthalimide (NMTP) was synthesized by the reaction of N-hydroxytetrabromophthalimide with either methacryloyl chloride or methacrylic acid in the presence of triethylamine or N, Ndicyclohexylcarbodiimide respectively. Binary copolymerization reactions of the prepared monomer with ethyl acrylate (EA), n-butyl methacrylate (n.BMA), tertiary butylacrylate (t.BA) and vinyl acetate (VA) were performed in methylene chloride at 65 degree C using 1 mol % azobisisobutylronitrile (AIBN) as initiator. The structure of the prepared monomer was investigated by IR and 1H NMR spectroscopy. The copolymer compositions were determined from bromine analysis. Copolymerization parameters for each system were calculated by the Fineman-Ross and Kelen-Tudos methods. The monomer reactivity ratios for the systems NMTP-EA, NMTP-n.BMA, NMTP-t.BA and NMTP-VA were found to be r1 0.180, r2 = 0.893, r1 = 0.025, r2 = 0.680, r1 0.014, r2 0.956 and r1 1.002, r2 1.004 respectively

UV-initiated template copolymerization of AM and MAPTAC: Microblock structure, copolymerization mechanism, and flocculation performance.

Science.gov (United States)

Li, Xiang; Zheng, Huaili; Gao, Baoyu; Sun, Yongjun; Liu, Bingzhi; Zhao, Chuanliang

2017-01-01

Flocculation as the core technology of sludge pretreatment can improve the dewatering performance of sludge that enables to reduce the cost of sludge transportation and the subsequent disposal costs. Therefore, synthesis of high-efficiency and economic flocculant is remarkably desired in this field. This study presents a cationic polyacrylamide (CPAM) flocculant with microblock structure synthesized through ultraviolet (UV)-initiated template copolymerization by using acrylamide (AM) and methacrylamido propyl trimethyl ammonium chloride (MAPTAC) as monomers, sodium polyacrylate (PAAS) as template, and 2,2'-azobis [2-(2-imidazolin-2-yl) propane] dihydrochloride (VA-044) as photoinitiator. The microblock structure of the CPAM was observed through nuclear magnetic resonance ( 1 H NMR and 13 C NMR) spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM) analyses. Furthermore, thermogravimetric/differential scanning calorimetry (TG/DSC) analysis was used to evaluate its thermal decomposition property. The copolymerization mechanism was investigated through the determination of the binding constant M K and study on polymerization kinetics. Results showed that the copolymerization was conducted in accordance with the I (ZIP) template polymerization mechanism, and revealed the coexistence of bimolecular termination free-radical reaction and mono-radical termination in the polymerization process. Results of sludge dewatering tests indicated the superior flocculation performance of microblock flocculant than random distributed CPAM. The residual turbidity, filter cake moisture content, and specific resistance to filtration reached 9.37 NTU, 68.01%, and 6.24 (10 12  m kg -1 ), respectively, at 40 mg L -1 of template poly(AM-MAPTAC) and pH 6.0. Furthermore, all flocculant except commercial CPAM showed a wide scope of pH application. Copyright © 2016 Elsevier Ltd. All rights reserved.

Modeling of continuous free-radical butadiene-styrene copolymerization process by the Monte Carlo method

Directory of Open Access Journals (Sweden)

T. A. Mikhailova

2016-01-01

Full Text Available In the paper the algorithm of modeling of continuous low-temperature free-radical butadiene-styrene copolymerization process in emulsion based on the Monte-Carlo method is offered. This process is the cornerstone of industrial production butadiene – styrene synthetic rubber which is the most widespread large-capacity rubber of general purpose. Imitation of growth of each macromolecule of the formed copolymer and tracking of the processes happening to it is the basis of algorithm of modeling. Modeling is carried out taking into account residence-time distribution of particles in system that gives the chance to research the process proceeding in the battery of consistently connected polymerization reactors. At the same time each polymerization reactor represents the continuous stirred tank reactor. Since the process is continuous, it is considered continuous addition of portions to the reaction mixture in the first reactor of battery. The constructed model allows to research molecular-weight and viscous characteristics of the formed copolymerization product, to predict the mass content of butadiene and styrene in copolymer, to carry out calculation of molecular-weight distribution of the received product at any moment of conducting process. According to the results of computational experiments analyzed the influence of mode of the process of the regulator introduced during the maintaining on change of characteristics of the formed butadiene-styrene copolymer. As the considered process takes place with participation of monomers of two types, besides listed the model allows to research compositional heterogeneity of the received product that is to carry out calculation of composite distribution and distribution of macromolecules for the size and structure. On the basis of the proposed algorithm created the software tool that allows you to keep track of changes in the characteristics of the resulting product in the dynamics.

Immobilization of glucose oxidase on sepharose by UV-initiated graft copolymerization

International Nuclear Information System (INIS)

D'Angiuro, L.; Cremonesi, P.

1982-01-01

The performance of a new method of enzyme immobilization based on photochemically initiated direct graft copolymerization was recently investigated. The immobilization reaction can be carried out in a simple way and by carefully selecting the reaction conditions, the enzyme-graft copolymer can be obtained as the main reaction product. Coupling efficiency of glucose oxidase has been found to depend only on the amount of photocatalyst (FeCl 3 ) fixed on Sepharose used as polysaccharide support. Small quantities of glycidylmethacrylate (GMA) (0.25 g/g dry Sepharose) are sufficient but necessary to achieve the best enzyme coupling efficiency (20-40%). Enzyme immobilization occurs very rapidly and the entire reaction occurs within 60 min. Reaction patterns and physicochemical characteristics of the obtained enzyme-graft copolymers exclude the glucose oxidase entrapment: therefore a covalent attachment mechanism may be proposed. The kinetic parameters of immobilized glucose oxidase (K/sub m/' = 2.0 x 10 -2 M) are quite similar to those of free enzyme (K/sub m/ = 1.93 x 10 -2 M), and no diffusion limitation phenomena are evidenced in samples having different enzyme or polymer content. Lyophilization, thermostability, and long-term continuous operation also have been investigated. The advantages of this method over that using vinylenzyme copolymerization are discussed

Copolymerization of ε-caprolactone with Epichlorohydrin by a Green Catalyst, Maghnite

Directory of Open Access Journals (Sweden)

Abdelghani Bouchama

2012-06-01

Full Text Available Most of the cationic initiators used in the synthesis of copolymers are expensive. They may be poisoned by products of the reaction or impurities present in the monomer feed, and contain heavy metals, such as chromium, mercury, antimony, etc., that presents environmental disposal problems for the user. Maghnite is a montmorillonite sheet silicate clay that is exchanged with protons to produce Maghnite-H+ (Mag-H+. This non-toxic and cheaper cationic catalyst was used for the copolymerization of ε-caprolactone (CL with epichlorohydrin (ECH. The effects of the amounts of Mag-H+ and the temperature on the synthesis of poly (ε-caprolactone-co-epichlorohydrin were studied. Increasing Maghnite-H+ proportion and temperature produced the increase in copolymerization yield. The copolymer obtained was characterized by 1H-NMR and IR spectroscopy. Copyright © 2012 BCREC UNDIP. All rights reserved.Received: 24th September 2011, Revised: 12nd December 2011; Accepted: 9th January 2012[How to Cite: A. Bouchama, M.I. Ferrahi, and M. Belbachir. (2012. Copolymerization of ε-caprolactone with Epichlorohydrin by a Green Catalyst, Maghnite. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (1: 43-48.  doi:10.9767/bcrec.7.1.1211.43-48][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.1.1211.43-48 ] | View in 

Predominant 1,2-insertion of styrene in the Pd-catalyzed alternating copolymerization with carbon monoxide.

Science.gov (United States)

Nozaki, K; Komaki, H; Kawashima, Y; Hiyama, T; Matsubara, T

2001-01-31

The regioselectivity of styrene insertion to an acyl-Pd bond was studied by NMR in (i) a stoichiomeric reaction and (ii) a copolymerization with CO. In the stoichiometric reaction of styrene with [(CH(3)CO)Pd(CH(3)CN)[(R,S)-BINAPHOS

Food enrichment with marine phospholipid emulsions

DEFF Research Database (Denmark)

Lu, Henna Fung Sieng; Nielsen, Nina Skall; Baron, Caroline P.

marine PL emulsions with and without addition of fish oil. The oxidative stability of marine PL emulsions was significantly influenced by the chemical composition of marine PL used for emulsions preparation. For instance, emulsions with good oxidative stability could be obtained when using raw materials...... with high purity, low fish oil content and high PL, cholesterol and α-tocopherol content. In addition, non-enzymatic browning reactions may also affect the oxidative stability of the marine PL emulsion. These reactions included Strecker degradation and pyrrolization, and their occurrence were due......Many studies have shown that marine phospholipids (PL) provide more advantages than fish oil. They seem to have better bioavailability, better resistance towards oxidation and higher content of eicosapentaenoic acids and docosahexaenoic acids than fish oil, which essentially contains triglycerides...

Basic and engineering studies of radiation induced reactions in the liquid phase. Final technical report, June 1, 1970-May 31, 1974

International Nuclear Information System (INIS)

1978-06-01

Laboratory studies reported on are ionic polymerization under superdry conditions, emulsion polymerization, and vinyl chloride polymerization. Engineering studies include the effect of moisture level on radiation-induced solution polymerization, effect of dose rate on radiation-induced emulsion polymerization of styrene, the effect of soap exchange in styrene emulsion polymerization, pilot plant studies of radiation induced emulsion polymerization of vinyl chloride, pilot plant studies of radiation-induced emulsion copolymerization of vinyl chloride with vinyl acetate, pilot plant study of radiation-induced graft emulsion polymerization of styrene onto polyvinyl chloride and poly(vinyl chloride-vinyl acetate), and radiation-induced precipitation polymerization of vinyl chloride in a flow reactor

Kinetic investigations of emulsion- and solvent-mediated radiation induced graft copolymerization of glycidyl methacrylate onto nylon-6 fibres

International Nuclear Information System (INIS)

Teo Ming Ting; Paveswari Sithambaranathan

2017-01-01

Kinetic behaviour of graft copolymerisation of glycidyl methacrylate onto nylon-6 fibres in solvent- and emulsion- media was investigated. The order for the dependence of the initial rate of grafting on the monomer concentration for solvent and emulsion grafting systems were found to be 1.65 and 1.57, respectively. The order of dependence of the initial rate of grafting on the absorbed dose was found to be 1.55 for solvent and 0.62 emulsion grafting systems. The results showed that grafting in both systems is controlled by diffusion mechanism and the degree of grafting can be effectively tuned by variation of the grafting parameters. (author)

Cobaltoporphyrin-Catalyzed CO 2 /Epoxide Copolymerization: Selectivity Control by Molecular Design

KAUST Repository

Anderson, Carly E.; Vagin, Sergei I.; Xia, Wei; Jin, Hanpeng; Rieger, Bernhard

2012-01-01

A series of cobalt(III) chloride porphyrin complexes of the general formula 5,10,15,20-tetra(p-alkoxy)phenylporphyrin cobalt chloride (4b-e) and the related 5,10,15,20-tetra(p-nitro)phenylporphyrin cobalt chloride (4f) are presented and their reactivity toward propylene oxide (PO)/CO 2 coupling/copolymerization is explored. While the nitro-substituted complex (4f), in conjunction with an onium salt, shows moderate activity toward cyclization, the 4b-e/onium systems show superior copolymerization activity in comparison to tetraphenylporphyrin Co(III) chloride (4a) with high selectivity and conversion to poly(propylene carbonate) (PPC). A comprehensive copolymerization behavior study of the alkoxy-substituted porphyrin complexes 4b-e in terms of reaction temperature and CO 2 pressure is presented. Complexes bearing longer alkoxy-substituents demonstrate the highest polymerization activity and molecular weights, however all substituted catalyst systems display a reduced tolerance to increased temperature with respect to PPC formation. Studies of the resulting polymer microstructures show excellent head-to-tail epoxide incorporation and near perfectly alternating poly(carbonate) character at lower polymerization temperatures. © 2012 American Chemical Society.

Cobaltoporphyrin-Catalyzed CO 2 /Epoxide Copolymerization: Selectivity Control by Molecular Design

KAUST Repository

Anderson, Carly E.

2012-09-11

A series of cobalt(III) chloride porphyrin complexes of the general formula 5,10,15,20-tetra(p-alkoxy)phenylporphyrin cobalt chloride (4b-e) and the related 5,10,15,20-tetra(p-nitro)phenylporphyrin cobalt chloride (4f) are presented and their reactivity toward propylene oxide (PO)/CO 2 coupling/copolymerization is explored. While the nitro-substituted complex (4f), in conjunction with an onium salt, shows moderate activity toward cyclization, the 4b-e/onium systems show superior copolymerization activity in comparison to tetraphenylporphyrin Co(III) chloride (4a) with high selectivity and conversion to poly(propylene carbonate) (PPC). A comprehensive copolymerization behavior study of the alkoxy-substituted porphyrin complexes 4b-e in terms of reaction temperature and CO 2 pressure is presented. Complexes bearing longer alkoxy-substituents demonstrate the highest polymerization activity and molecular weights, however all substituted catalyst systems display a reduced tolerance to increased temperature with respect to PPC formation. Studies of the resulting polymer microstructures show excellent head-to-tail epoxide incorporation and near perfectly alternating poly(carbonate) character at lower polymerization temperatures. © 2012 American Chemical Society.

Progression of radical reactions on microscopic scale in food emulsions

DEFF Research Database (Denmark)

Raudsepp, Piret

Understanding the progression of lipid oxidation in oil-in-water emulsions from the aspect of the food quality and safety, consumer satisfaction and cleaner food label is of importance, because most of the food emulsions are oil-in-water emulsions. There is an increasing tendency in the food...... industry to incorporate unsaturated oils into food products, but that results in shortened shelf-life. Therefore, studying the factors and consequences of the oxidative instability provides beneficial insight into prolonging the antioxidative stage and inhibiting undergoing oxidation processes to improve...... the food quality and increase the shelflife of the food products. In the present work, lipid oxidation in oil-in-water emulsions was studied via conventional analytical and via novel state-of-the-art techniques. For the first time, the effect of mixing emulsions made of saturated medium-chain triglyceride...

Kinetic advantages of using microwaves in the emulsion polymerization of MMA

Energy Technology Data Exchange (ETDEWEB)

Costa, C. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil); Santos, A.F.; Fortuny, M. [Programa de Mestrado em Engenharia de Processos, Universidade Tiradentes, Instituto de Tecnologia e Pesquisa, Av. Murilo Dantas, 300, CEP: 49032-490, Aracaju, SE (Brazil); Araujo, P.H.H. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil); Sayer, C. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil)], E-mail: csayer@enq.ufsc.br

2009-03-01

Microwave irradiation has been an interesting alternative for heating systems and several chemical reactions. In polymerization processes, microwaves can enhance reaction rates or improve specific characteristics of the formed polymer. In this work, the use of microwave irradiation in emulsion polymerization reactions has been studied, using a commercial microwave reactor, which is able to perform syntheses under controlled conditions of temperature and power. Methyl methacrylate emulsion polymerization reactions were faster, resulting in smaller polymer particles, in comparison to the conventional heating method (reactions in a jacketed reactor). Different effects were observed in the emulsion polymerization of butyl acrylate. To study the effect of high power microwave irradiation upon the emulsion polymerization, a pulsed irradiation strategy was developed, in which the samples were repeatedly heated within short intervals of time (about 27 s) at the maximum microwave power. A significant reduction of the total time of irradiation was observed in reactions carried out under the pulsed scheme, showing the kinetic advantages of using microwaves in emulsion polymerization processes.

Radiation induced graft copolymerization of acrylamide onto poly (3-hydroxybutyrate)

International Nuclear Information System (INIS)

Gonzalez Torres, Maykel; Rapado Paneque, Manuel; Paredes Zaldivar, Mayte; Altanes Valentin, Sonia; Barrera Gonzalez, Gisela

2008-01-01

The graft copolymer poly (3-hydroxybutyrate)-g- polyacrylamide [P (HB-g-AAm)] was synthesized by radiation induced graft copolymerization of acrylamide onto poly (3-hydroxybutyrate). The study was conducted by the simultaneous irradiation method. The structure of [P (HB-g-AAm)] was identified by Fourier Transform Infrared (FTIR) spectroscopy. Thermal behavior of the graft copolymer was also studied by Thermal Gravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC). From the results it was found that FTIR studies showed new signals (stretching -N-H) as strong evidence of grafting. The grafting degree was found to be 10 % and the thermodynamic parameter obtained from the DSC thermogram of plain PHB and the graft copolymer varied showing decrease in the material crystallinity and increase in the glass transition temperature. These results demonstrate that the radiation induced graft copolymerization reaction of acrylamide onto PHB was successively achieved. (Author)

Copper mediated controlled radical copolymerization of styrene and2-ethylhexyl acrylate and determination of their reactivity ratios.

Directory of Open Access Journals (Sweden)

Bishnu Prasad Koiry

2014-10-01

Full Text Available Copolymerization is an important synthetic tool to prepare polymers with desirable combination of properties which are difficult to achieve from the different homopolymers concerned. This investigation reports the copolymerization of 2-ethylhexyl acrylate (EHA and styrene using copper bromide (CuBr as catalyst in combination with N,N,N’,N,N- pentamethyldiethylenetriamine (PMDETA as ligand and 1-phenylethyl bromide (PEBr as initiator. Linear kinetic plot and linear increase in molecular weights versus conversion indicate that copolymerization reactions were controlled. The copolymer composition was calculated using 1H NMR studies. The reactivity ratio of styrene and EHA (r1 and r2 were determined using the Finemann-Ross (FR, inverted Finemann-Ross (FR and Kelen-Tudos (KT methods. Thermal properties of the copolymers were also studied by using TGA and DSC analysis.

Extraction of palm tree cellulose and its functionalization via graft copolymerization.

Science.gov (United States)

Al-Hoqbani, Abdulmajeed A; Abdel-Halim, E S; Al-Deyab, Salem S

2014-09-01

The work in this paper was planned with the aim of extracting the cellulosic component of palm tree waste and functionalizing this cellulose through graft copolymerization with acrylic acid. The cellulose extraction included hot alkali treatment with aqueous sodium hydroxide to remove the non-cellulosic binding materials. The alkali treatment was followed by an oxidative bleaching using peracid/hydrogen peroxide mixture with the aim of removing the rest of non-cellulosic materials to improve the fiber hydrophilicity and accessibility towards further grafting reaction. Optimum conditions for cellulose extraction are boiling in 5% (W/V) NaOH in a material to liquor ratio of 1:20 for 1 h then bleaching with 60 ml/l bleaching mixture at initial pH value of 6.5 for 30 min. The pH of the bleaching medium is turned to the alkaline range 11 and bleaching continues for extra 30 min. Graft copolymerization reaction was initiated by potassium bromate/thiourea dioxide redox system. Optimum conditions for grafting are 30 mmol of potassium bromate, 30 mmol of thiourea dioxide and 150 g of acrylic acid (each per 100 g of cellulose). The polymerization reaction was carried out for 120 min at 50°C using a material to liquor ratio of 1:20. Copyright © 2014 Elsevier B.V. All rights reserved.

Thermal stability and mechanism of decomposition of emulsion explosives in the presence of pyrite

International Nuclear Information System (INIS)

Xu, Zhi-Xiang; Wang, Qian; Fu, Xiao-Qi

2015-01-01

Highlights: • An exothermic reaction occurs at about 200 °C between pyrite and ammonium nitrate (emulsion explosives). • The essence of reaction between emulsion explosives and pyrite is reaction between ammonium nitrate and pyrite. • The excellent thermal stability of emulsion explosives does not mean it was also showed when pyrite was added. • A new overall reaction has been proposed as: • 14FeS_2(s) + 91NH_4NO_3(s) → 52NO(g) + 26SO_2(g) + 6Fe_2O_3(s) + 78NH_3(g) + 26N_2O(g) + 2FeSO_4(s) + 65H_2O(g). - Abstract: The reaction of emulsion explosives (ammonium nitrate) with pyrite was studied using techniques of TG-DTG-DTA. TG–DSC–MS was also used to analyze samples thermal decomposition process. When a mixture of pyrite and emulsion explosives was heated at a constant heating rate of 10 K/min from room temperature to 350 °C, exothermic reactions occurred at about 200 °C. The essence of reaction between emulsion explosives and pyrite is the reaction between ammonium nitrate and pyrite. Emulsion explosives have excellent thermal stability but it does not mean it showed the same excellent thermal stability when pyrite was added. Package emulsion explosives were more suitable to use in pyrite shale than bulk emulsion explosives. The exothermic reaction was considered to take place between ammonium nitrate and pyrite where NO, NO_2, NH_3, SO_2 and N_2O gases were produced. Based on the analysis of the gaseous, a new overall reaction was proposed, which was thermodynamically favorable. The results have significant implication in the understanding of stability of emulsion explosives in reactive mining grounds containing pyrite minerals.

Thermal stability and mechanism of decomposition of emulsion explosives in the presence of pyrite

Energy Technology Data Exchange (ETDEWEB)

Xu, Zhi-Xiang; Wang, Qian [School of Energy and Power Engineering, Jiangsu University, Zhenjiang 212013 (China); Fu, Xiao-Qi, E-mail: xzx19820708@163.com [School of Chemistry and Chemical Engineering, Jiangsu University Zhenjiang 212013 (China)

2015-12-30

Highlights: • An exothermic reaction occurs at about 200 °C between pyrite and ammonium nitrate (emulsion explosives). • The essence of reaction between emulsion explosives and pyrite is reaction between ammonium nitrate and pyrite. • The excellent thermal stability of emulsion explosives does not mean it was also showed when pyrite was added. • A new overall reaction has been proposed as: • 14FeS{sub 2}(s) + 91NH{sub 4}NO{sub 3}(s) → 52NO(g) + 26SO{sub 2}(g) + 6Fe{sub 2}O{sub 3}(s) + 78NH{sub 3}(g) + 26N{sub 2}O(g) + 2FeSO{sub 4}(s) + 65H{sub 2}O(g). - Abstract: The reaction of emulsion explosives (ammonium nitrate) with pyrite was studied using techniques of TG-DTG-DTA. TG–DSC–MS was also used to analyze samples thermal decomposition process. When a mixture of pyrite and emulsion explosives was heated at a constant heating rate of 10 K/min from room temperature to 350 °C, exothermic reactions occurred at about 200 °C. The essence of reaction between emulsion explosives and pyrite is the reaction between ammonium nitrate and pyrite. Emulsion explosives have excellent thermal stability but it does not mean it showed the same excellent thermal stability when pyrite was added. Package emulsion explosives were more suitable to use in pyrite shale than bulk emulsion explosives. The exothermic reaction was considered to take place between ammonium nitrate and pyrite where NO, NO{sub 2}, NH{sub 3}, SO{sub 2} and N{sub 2}O gases were produced. Based on the analysis of the gaseous, a new overall reaction was proposed, which was thermodynamically favorable. The results have significant implication in the understanding of stability of emulsion explosives in reactive mining grounds containing pyrite minerals.

Mechanism of alternating copolymerization of methyl methacrylate with styrene in the presence of diethylaluminum chloride

International Nuclear Information System (INIS)

Zubov, V.P.; Lachinov, M.B.; Ignatova, E.V.; Georgiev, G.S.; Golubev, V.B.; Kabanov, V.A.

1982-01-01

A kinetic study of the propagation mechanism of the alternating copolymerization of styrene (St) with methyl methacrylate (MMA) in the presence of a complexing agent (diethylaluminum chloride, DEAC) in bulk and in tetrachloroethylene solutions at a molar ratio DEAC/MMA = 0.5 has been carried out. It has been shown that the copolymerization is a chain radical process characterized by a short active-center lifetime, bimolecular termination, and high rate of chain transfer to the complexed MMA. A kinetic scheme has been proposed for the propagation mechanism of alternating copolymerization in the presence of a complexing agent not requiring independent measurements of the equilibrium constant of complexation. It has been found that spontaneous and uv-initiated copolymerizations in the system have different mechanisms of initiation and a common mechanism of propagation. The propagation proceeds by addition of single monomers as well as donor-acceptor complexes of the comonomers to the propagation radicals, with the first mechanism being predominant. Inclusion of the monomers in the complex leads to an increase of the St reactivity and to a decrease of the MMA reactivity in propagation to the corresponding macroradicals in comparison with the reactivity of the free monomers. A number of kinetic and statistical parameters of the propagation reaction have been calculated

Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

International Nuclear Information System (INIS)

Sundardi, F.; Kadariah, S.

1986-01-01

A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

Chemoselective alternating copolymerization of limonene dioxide and carbon dioxide : a new highly functional aliphatic epoxy polycarbonate

NARCIS (Netherlands)

Li, C.; Sablong, R.J.; Koning, C.E.

The alternating copolymerization of biorenewable limonene dioxide with carbon dioxide (CO2) catalyzed by a zinc β-diiminate complex is reported. The chemoselective reaction results in linear amorphous polycarbonates that carry pendent methyloxiranes and exhibit glass transition temperatures (Tg) up

Synthesis of Terpolymers with Homogeneous Composition by Free Radical Copolymerization of Maleic Anhydride, Perfluorooctyl and Butyl or Dodecyl Methacrylates: Application of the Continuous Flow Monomer Addition Technique

Directory of Open Access Journals (Sweden)

Marian Szkudlarek

2017-11-01

Full Text Available Terpolymers of homogeneous composition were prepared by free radical copolymerization of butyl or dodecyl methacrylate, 1H,1H,2H,2H-perfluorodecyl methacrylate and maleic anhydride using the continuous monomer addition technique. The copolymerization reactions were performed at 65 °C in the presence of azobisisobutyronitrile as an initiator in a mixture of methyl ethyl ketone and 1,3-bis (trifluoromethylbenzene. The monomers and initiator are added to the reaction mixture with the same rate they are consumed in 5- and 10-fold excess compared to the initial monomer stock. The obtained terpolymers with molecular weights Mn = 50,000–70,000 are of uniform composition, close to the composition determined in low conversion experiments, proving the principle of the chosen concept. The kinetic data necessary for the design of the continuous addition experiment were obtained from binary copolymerization experiments at low monomer conversion (to avoid compositional drift. In addition, the so-called terpolymerization parameter was determined from ternary copolymerization experiments.

Electrochemical copolymerization of thiophene derivatives; a precursor to photovoltaic devices

International Nuclear Information System (INIS)

Kumar, Prajwal; Ranjith, K.; Gupta, Satyajit; Ramamurthy, Praveen C.

2011-01-01

Highlights: → This work presents an electrochemical technique for the polymerization and copolymerization of thiophene derivatives. → Copolymerization of thiophene based monomers like 7,9-dithiophene-2yl-8H-cyclopenta[a]acenaphthalene-8-one and 3-hexylthiophene are synthesized. → Study of the structural, optical, thermal, conductivity, morphological, band gap and impedance measurements of the copolymer indicates a suitable material for photovoltaic applications. - Abstract: This work presents an electrochemical technique for the polymerization and copolymerization of thiophene derivatives like 7,9-dithiophene-2yl-8H-cyclopenta[a]acenaphthalene-8-one and 3-hexylthiophene. The structural characterization of chemically synthesized monomers and electrochemically synthesized polymers was carried out by nuclear magnetic resonance and Fourier transform infrared spectroscopy. Thermal characterizations indicate that copolymer has increased thermal stability than that of homopolymer. Morphological studies of the polymerized films carried out by scanning electron microscopy shows network structure of copolymer. Optical properties of the homopolymers and copolymer were studied by UV-visible spectrometer and it was observed that band gap of copolymer is less than the homopolymers. HOMO and LUMO levels, band gap values of the respective polymers were also calculated from the cyclic voltammetry technique with various scan rates. By the peak current obtained from various scan rates shows that all polymerization reactions are diffusion controlled process. Charge transfer resistances of polymers were determined using Nyquist plots. Conductivity of synthesized polymers shows higher conductivity for copolymer than homopolymers.

Thermal stability and mechanism of decomposition of emulsion explosives in the presence of pyrite.

Science.gov (United States)

Xu, Zhi-Xiang; Wang, Qian; Fu, Xiao-Qi

2015-12-30

The reaction of emulsion explosives (ammonium nitrate) with pyrite was studied using techniques of TG-DTG-DTA. TG-DSC-MS was also used to analyze samples thermal decomposition process. When a mixture of pyrite and emulsion explosives was heated at a constant heating rate of 10K/min from room temperature to 350°C, exothermic reactions occurred at about 200°C. The essence of reaction between emulsion explosives and pyrite is the reaction between ammonium nitrate and pyrite. Emulsion explosives have excellent thermal stability but it does not mean it showed the same excellent thermal stability when pyrite was added. Package emulsion explosives were more suitable to use in pyrite shale than bulk emulsion explosives. The exothermic reaction was considered to take place between ammonium nitrate and pyrite where NO, NO2, NH3, SO2 and N2O gases were produced. Based on the analysis of the gaseous, a new overall reaction was proposed, which was thermodynamically favorable. The results have significant implication in the understanding of stability of emulsion explosives in reactive mining grounds containing pyrite minerals. Copyright © 2015 Elsevier B.V. All rights reserved.

Palladium/IzQO-Catalyzed Coordination-Insertion Copolymerization of Ethylene and 1,1-Disubstituted Ethylenes Bearing a Polar Functional Group.

Science.gov (United States)

Yasuda, Hina; Nakano, Ryo; Ito, Shingo; Nozaki, Kyoko

2018-02-07

Coordination-insertion copolymerization of ethylene with 1,1-disubstituted ethylenes bearing a polar functional group, such as methyl methacrylate (MMA), is a long-standing challenge in catalytic polymerization. The major obstacle for this process is the huge difference in reactivity of ethylene versus 1,1-disubstituted ethylenes toward both coordination and insertion. Herein we report the copolymerization of ethylene and 1,1-disubstituted ethylenes by using an imidazo[1,5-a]quinolin-9-olate-1-ylidene-supported palladium catalyst. Various types of 1,1-disubstituted ethylenes were successfully incorporated into the polyethylene chain. In-depth characterization of the obtained copolymers and mechanistic inferences drawn from stoichiometric reactions of alkylpalladium complexes with methyl methacrylate and ethylene indicate that the copolymerization proceeds by the same coordination-insertion mechanism that has been postulated for ethylene.

Kinetic investigations of graft copolymerization of sodium styrene sulfonate onto electron beam irradiated poly(vinylidene fluoride) films

Energy Technology Data Exchange (ETDEWEB)

Mahmoud Nasef, Mohamed, E-mail: mahmoudeithar@fkkksa.utm.m [Institute of Hydrogen Economy, International City Campus, Universiti Teknologi Malaysia, Jalan Semarak, 54100 Kuala Lumpur (Malaysia); Chemical Engineering Department, Faculty of Chemical and Natural Resources Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Saidi, Hamdani [Institute of Hydrogen Economy, International City Campus, Universiti Teknologi Malaysia, Jalan Semarak, 54100 Kuala Lumpur (Malaysia); Chemical Engineering Department, Faculty of Chemical and Natural Resources Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Mohd Dahlan, Khairul Zaman [Radiation Processing Technology Division, Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

2011-01-15

Graft copolymerization of sodium styrene sulfonate (SSS) onto electron beam (EB) irradiated poly(vinylidene fluoride) (PVDF) films was investigated to find out a simple preparation process for sulfonic acid proton exchange membranes with respect to monomer concentration, absorbed dose, temperature, film thickness and storage time. The reaction order of the monomer concentration and absorbed dose of grafting was found to be 2.84 and 1.20, respectively. The overall activation energy for graft copolymerization reaction was calculated to be 11.36 kJ/mol. The initial rate of grafting was found to decrease with an increase in the film thickness. The trapped radicals in the irradiated PVDF films remained effective in initiating the reaction without considerable loss in grafting level up to 180 days, when stored under -60 {sup o}C. The presence and distribution of polystyrene sulfonate grafts in the obtained membranes were observed by Fourier transform infrared (FTIR) spectroscopic analysis, scanning optical microscope and scanning transmission electron microscopy (STEM) coupled with X-ray energy dispersive (EDX), respectively.

Radiation-induced copolymerization of hexafluoroacetone with α-olefins

International Nuclear Information System (INIS)

Matsuda, O.; Watanabe, S.; Okamoto, J.; Machi, S.; Tabata, Y.

1977-01-01

The copolymerization of hexafluoroacetone with higher α-olefins above butene, such as 1-pentene (I), 1-hexene (II), 1-octene (III), 2-methyl-1-butene (IV), 2-methyl-1-pentene (V), 3-methyl-1-butene (VI), and 4-methyl-1-pentene (VII) was studied at relatively low temperatures by γ-ray irradiation. Copolymerization of II, IV, V, and VII with hexafluoroacetone was found to scarcely take place at -78 0 C in bulk, but the addition of trichlorotrifluoroethane in amounts to yield equimolar mixtures resulted in conversion of 15.7 percent for IV and of 2.1 to 4.0 percent for the other α-olefins. Higher conversion of V at -78 0 C than at 0 0 C suggest that copolymerization may take place via an ionic mechanism. The effects of various additives on the copolymerization are reported. Infrared spectral studies indicated that the double bond of the α-olefins is opened to form a polymer. The C--O double bond of the hexafluoroacetone and the α-olefin double bond are opened to form the copolymer

High-pressure copolymerization of C 2H 4 and CO

Science.gov (United States)

Buback, M.; Tups, H.

1986-05-01

Kinetics of the free radical high-pressure copolymerization of ethylene and carbon monoxide using thermal, chemical, and laser-photochemical initiation have been investigated via quantitative infrared and near infrared spectroscopy up to 2300 bar and 513 K. The slow thermal copolymerization is influenced by the formation of metal carbonyls inside the stainless steel cell. With chemical initiation, using 120 ppm oxygen, ethylene and CO polymerize to polyketone without any indication of additional products. The photo-copolymerization induced by an exciplex laser working on the KrF line at 248 nm, has been studied between 486 K and 513 K up to 2300 bar and for CO mole fractions up to 3 percent. Overall quantum yields of about 2000 copolymerizing molecules per one absorbed laser photon are observed.

Concerning the Deactivation of Cobalt(III)-Based Porphyrin and Salen Catalysts in Epoxide/CO 2 Copolymerization

KAUST Repository

Xia, Wei

2015-02-05

© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Functioning as active catalysts for propylene oxide (PO) and carbon dioxide copolymerization, cobalt(III)-based salen and porphyrin complexes have drawn great attention owing to their readily modifiable nature and promising catalytic behavior, such as high selectivity for the copolymer formation and good regioselectivity with respect to the polymer microstructure. Both cobalt(III)-salen and porphyrin catalysts have been found to undergo reduction reactions to their corresponding catalytically inactive cobalt(II) species in the presence of propylene oxide, as evidenced by UV/Vis and NMR spectroscopies and X-ray crystallography (for cobalt(II)-salen). Further investigations on a TPPCoCl (TPP=tetraphenylporphyrin) and NaOMe system reveal that such a catalyst reduction is attributed to the presence of alkoxide anions. Kinetic studies of the redox reaction of TPPCoCl with NaOMe suggests a pseudo-first order in cobalt(III)-porphyrin. The addition of a co-catalyst, namely bis(triphenylphosphine)iminium chloride (PPNCl), into the reaction system of cobalt(III)-salen/porphyrin and PO shows no direct stabilizing effect. However, the results of PO/CO2 copolymerization by cobalt(III)-salen/porphyrin with PPNCl suggest a suppressed catalyst reduction. This phenomenon is explained by a rapid transformation of the alkoxide into the carbonate chain end in the course of the polymer formation, greatly shortening the lifetime of the autoreducible PO-ring-opening intermediates, cobalt(III)-salen/porphyrin alkoxides. CO2 saves: The deactivation of cobalt(III)-porphyrin and salen catalysts in propylene oxide/carbon dioxide copolymerization is systematically investigated, revealing a proposed mechanism for the catalyst reduction (see scheme).

Concerning the Deactivation of Cobalt(III)-Based Porphyrin and Salen Catalysts in Epoxide/CO 2 Copolymerization

KAUST Repository

Xia, Wei; Salmeia, Khalifah A.; Vagin, Sergei I.; Rieger, Bernhard

2015-01-01

© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Functioning as active catalysts for propylene oxide (PO) and carbon dioxide copolymerization, cobalt(III)-based salen and porphyrin complexes have drawn great attention owing to their readily modifiable nature and promising catalytic behavior, such as high selectivity for the copolymer formation and good regioselectivity with respect to the polymer microstructure. Both cobalt(III)-salen and porphyrin catalysts have been found to undergo reduction reactions to their corresponding catalytically inactive cobalt(II) species in the presence of propylene oxide, as evidenced by UV/Vis and NMR spectroscopies and X-ray crystallography (for cobalt(II)-salen). Further investigations on a TPPCoCl (TPP=tetraphenylporphyrin) and NaOMe system reveal that such a catalyst reduction is attributed to the presence of alkoxide anions. Kinetic studies of the redox reaction of TPPCoCl with NaOMe suggests a pseudo-first order in cobalt(III)-porphyrin. The addition of a co-catalyst, namely bis(triphenylphosphine)iminium chloride (PPNCl), into the reaction system of cobalt(III)-salen/porphyrin and PO shows no direct stabilizing effect. However, the results of PO/CO2 copolymerization by cobalt(III)-salen/porphyrin with PPNCl suggest a suppressed catalyst reduction. This phenomenon is explained by a rapid transformation of the alkoxide into the carbonate chain end in the course of the polymer formation, greatly shortening the lifetime of the autoreducible PO-ring-opening intermediates, cobalt(III)-salen/porphyrin alkoxides. CO2 saves: The deactivation of cobalt(III)-porphyrin and salen catalysts in propylene oxide/carbon dioxide copolymerization is systematically investigated, revealing a proposed mechanism for the catalyst reduction (see scheme).

Radiation-induced copolymerization of α,β,β-trifluoroacrylonitrile with α-olefin

International Nuclear Information System (INIS)

Matsuda, O.; Kostov, G.K.; Tabata, Y.; Machi, S.

1979-01-01

Homopolymerization and copolymerization of α,β,β-trifluoroacrylonitrile (FAN) with α-olefins were carried out in bulk by γ-ray irradiation at 25 0 C. FAN gives very small quantities of brown and greasy low molecular weight polymer. Cyano groups in FAN polymer were found to be readily hydrolyzed to acid amide groups in the atmosphere. FAN was found to copolymerize with ethylene, propylene, and isobutylene via a radical mechanism to form equimolar copolymers in a wide range of monomer compositions. The polymerization rate increases linearly with FAN fraction in the monomer mixture. These copolymers are also hydrolyzed in the atmosphere, and the hydrolysis proceeds with more difficulty for the copolymer with higher α-olefin. The reactivity ratios r 1 (FAN) and r 2 (α-olefin) were determined to be 0.01 and 0.12 for the FAN/ethylene copolymerization and 0.01 and 0.07 for the FAN/propylene copolymerization. These results confirm that an alternating copolymerization takes place in the FAN/α-olefin system

Wettability modification of rock cores by fluorinated copolymer emulsion for the enhancement of gas and oil recovery

Energy Technology Data Exchange (ETDEWEB)

Feng Chunyan [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Kong Ying, E-mail: yingkong1967@yahoo.com.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Jiang Guancheng [MOE Key Laboratory of Petroleum Engineering, China University of Petroleum, Beijing 102249 (China); Yang Jinrong; Pu Chunsheng [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266555 (China); Zhang Yuzhong [Key Lab of Hollow Fibre Membrane Materials and Membrane Process, Tianjin Polytechnic University, Tianjin 300160 (China)

2012-07-01

The fluorine-containing acrylate copolymer emulsion was prepared with butyl acrylate, methacrylic acid and 1H, 1H, 2H, 2H-perfluorooctyl acrylate as monomers. Moreover, the structure of the copolymer was verified by Fourier transform infrared (FTIR), nuclear magnetic resonance ({sup 1}H NMR and {sup 19}F NMR) and X-ray photoelectron spectroscopy (XPS) analyses. The results showed that all the monomers had been copolymerized and the presence of fluorine moieties. The contact angle (CA) analyses, capillary rise and imbibition spontaneous tests were used to estimate the influence of the copolymer emulsion on the wettability of gas reservoirs. It was observed that the rock surface was of large contact angles of water, oilfield sewage, hexadecane and crude oil after treatment with the emulsion. The capillary rise results indicated that the contact angles of water/air and oil/air systems increased from 60 Degree-Sign and 32 Degree-Sign to 121 Degree-Sign and 80 Degree-Sign , respectively, due to the emulsion treatment. Similarly, because of wettability alteration by the fluoropolymer, the imbibition of water and oil in rock core decreased significantly. Experimental results demonstrated that the copolymer emulsion can alter the wettability of porous media from strong liquid-wetting to gas-wetting. This work provides a cost-effective method to prepare the fluoropolymer which can increase gas deliverability by altering the wettability of gas-condensate reservoirs and mitigating the water block effect.

To Model Chemical Reactivity in Heterogeneous Emulsions, Think Homogeneous Microemulsions.

Science.gov (United States)

Bravo-Díaz, Carlos; Romsted, Laurence Stuart; Liu, Changyao; Losada-Barreiro, Sonia; Pastoriza-Gallego, Maria José; Gao, Xiang; Gu, Qing; Krishnan, Gunaseelan; Sánchez-Paz, Verónica; Zhang, Yongliang; Dar, Aijaz Ahmad

2015-08-25

Two important and unsolved problems in the food industry and also fundamental questions in colloid chemistry are how to measure molecular distributions, especially antioxidants (AOs), and how to model chemical reactivity, including AO efficiency in opaque emulsions. The key to understanding reactivity in organized surfactant media is that reaction mechanisms are consistent with a discrete structures-separate continuous regions duality. Aggregate structures in emulsions are determined by highly cooperative but weak organizing forces that allow reactants to diffuse at rates approaching their diffusion-controlled limit. Reactant distributions for slow thermal bimolecular reactions are in dynamic equilibrium, and their distributions are proportional to their relative solubilities in the oil, interfacial, and aqueous regions. Our chemical kinetic method is grounded in thermodynamics and combines a pseudophase model with methods for monitoring the reactions of AOs with a hydrophobic arenediazonium ion probe in opaque emulsions. We introduce (a) the logic and basic assumptions of the pseudophase model used to define the distributions of AOs among the oil, interfacial, and aqueous regions in microemulsions and emulsions and (b) the dye derivatization and linear sweep voltammetry methods for monitoring the rates of reaction in opaque emulsions. Our results show that this approach provides a unique, versatile, and robust method for obtaining quantitative estimates of AO partition coefficients or partition constants and distributions and interfacial rate constants in emulsions. The examples provided illustrate the effects of various emulsion properties on AO distributions such as oil hydrophobicity, emulsifier structure and HLB, temperature, droplet size, surfactant charge, and acidity on reactant distributions. Finally, we show that the chemical kinetic method provides a natural explanation for the cut-off effect, a maximum followed by a sharp reduction in AO efficiency with

Complex-radical copolymerization of vinyl monomers on organoelemental initiators

International Nuclear Information System (INIS)

Grishin, D.F.

1993-01-01

Data on regularities of the initiation and growth of the (co)polymerization of polar vinyl series monomers on organo-elemental initiator, organo-boron in particular, are generalized. The effect of organo-metallic compounds and some phenol type inhibitors on the rate of acrylate (co)polymerization is analyzed from view of the change of electroacceptor properties (electrophilicity) of macroradicals

Copolymerization of propene and styrene using a zirconocene - methylaluminoxane initiator system

International Nuclear Information System (INIS)

Rabagliati, F.M.; Rodriguez, F.J.; Quijada, R.; Galland, G.B.

2009-01-01

The copolymerization of propene with styrene has been tested using the rac-Et(Ind) 2 ZrCl 2 -methylaluminoxane initiator system. The various proportion of styrene in initial feed showed an important effect on the polymerization activity. Low contents of styrene in the reaction produced a considerable fall in the activity. Respect to thermal behavior, it is noted that obtained propene/styrene copolymers showed Tm values slightly lower than the corresponding polypropene one. NMR spectroscopy allowed to confirm that the copolymer composition includes a very low incorporation of styrene in polypropylene chains. (author)

Radical Copolymerization Kinetics of Bio-Renewable Butyrolactone Monomer in Aqueous Solution

Directory of Open Access Journals (Sweden)

Sharmaine B. Luk

2017-10-01

Full Text Available The radical copolymerization kinetics of acrylamide (AM and the water-soluble monomer sodium 4-hydroxy-4-methyl-2-methylene butanoate (SHMeMB, formed by saponification of the bio-sourced monomer γ-methyl-α-methylene-γ-butyrolactone (MeMBL, are investigated to explain the previously reported slow rates of reaction during synthesis of superabsorbent hydrogels. Limiting conversions were observed to decrease with increased temperature during SHMeMB homopolymerization, suggesting that polymerization rate is limited by depropagation. Comonomer composition drift also increased with temperature, with more AM incorporated into the copolymer due to SHMeMB depropagation. Using previous estimates for the SHMeMB propagation rate coefficient, the conversion profiles were used to estimate rate coefficients for depropagation and termination (kt. The estimate for kt,SHMeMB was found to be of the same order of magnitude as that recently reported for sodium methacrylate, with the averaged copolymerization termination rate coefficient dominated by the presence of SHMeMB in the system. In addition, it was found that depropagation still controlled the SHMeMB polymerization rate at elevated temperatures in the presence of added salt.

Aqueous polymer emulsions by chemical modifications of thermosetting alternating polyketones

NARCIS (Netherlands)

Zhang, Youchun; Broekhuis, A. A.; Picchioni, F.

2007-01-01

Aqueous polymer emulsions were prepared by chemical modifications of thermosetting alternating polyketones in a one-pot reaction. Polymeric amines derived from the polyketones can act as polymeric surfactants for the self-emulsification of polyketones. The stability and structure of the emulsions

Integrated, Continuous Emulsion Creamer.

Science.gov (United States)

Cochrane, Wesley G; Hackler, Amber L; Cavett, Valerie J; Price, Alexander K; Paegel, Brian M

2017-12-19

Automated and reproducible sample handling is a key requirement for high-throughput compound screening and currently demands heavy reliance on expensive robotics in screening centers. Integrated droplet microfluidic screening processors are poised to replace robotic automation by miniaturizing biochemical reactions to the droplet scale. These processors must generate, incubate, and sort droplets for continuous droplet screening, passively handling millions of droplets with complete uniformity, especially during the key step of sample incubation. Here, we disclose an integrated microfluidic emulsion creamer that packs ("creams") assay droplets by draining away excess oil through microfabricated drain channels. The drained oil coflows with creamed emulsion and then reintroduces the oil to disperse the droplets at the circuit terminus for analysis. Creamed emulsion assay incubation time dispersion was 1.7%, 3-fold less than other reported incubators. The integrated, continuous emulsion creamer (ICEcreamer) was used to miniaturize and optimize measurements of various enzymatic activities (phosphodiesterase, kinase, bacterial translation) under multiple- and single-turnover conditions. Combining the ICEcreamer with current integrated microfluidic DNA-encoded library bead processors eliminates potentially cumbersome instrumentation engineering challenges and is compatible with assays of diverse target class activities commonly investigated in drug discovery.

Y-shaped Folic Acid-Conjugated PEG-PCL Copolymeric Micelles for Delivery of Curcumin.

Science.gov (United States)

Feng, Runliang; Zhu, Wenxia; Chu, Wei; Teng, Fangfang; Meng, Ning; Deng, Peizong; Song, Zhimei

2017-01-01

Curcumin is a natural hydrophobic product showing anticancer activity. Many studies show its potential use in the field of cancer treatment due to its safety and efficiency. However, its application is limited due to its low water-solubility and poor selective delivery to cancer. A Y-shaped folic acid-modified poly (ethylene glycol)-b-poly (ε-caprolactone)2 copolymer was prepared to improve curcumin solubility and realize its selective delivery to cancer. The copolymer was synthesized through selective acylation reaction of folic acid with α- monoamino poly(ethylene glycol)-b-poly(ε-caprolactone)2. Curcumin was encapsulated into the copolymeric micelles with 93.71% of encapsulation efficiency and 11.94 % of loading capacity. The results from confocal microscopy and cellular uptake tests showed that folic acid-modified copolymeric micelles could improve cellular uptake of curcumin in Hela and HepG2 cells compared with folic acid-unmodified micelles. In vitro cytotoxicity assay showed that folic acid-modified micelles improved anticancer activity against Hela and HepG2 cells in comparison to folic acidunmodified micelles. Meanwhile, both drug-loaded micelles demonstrated higher activity against Hela cell lines than HepG2. The research results suggested that the folic acid-modified Y-shaped copolymeric micelles should be used to enhance hydrophobic anticancer drugs' solubility and their specific delivery to folic acid receptors-overexpressed cancer. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Stabilitas emulsi kopolimer S-GMA (stirena – glisidil metakrilat

Directory of Open Access Journals (Sweden)

Isananto Winursito

1992-08-01

Full Text Available Epoxy groups in glycidyl methacrylate (GMA units have been available for the reaction with amine of proteins or other biological active substrates to prepare biomaterials and hybrid devices. Soap-soap copolymerization of GMA with styrene (S result the formation of stable latex. Hydrolysis of epoxy groups in copolymer particles increased emulsion stability. The effect of pH, temperature and reaction time in the hydrolysis of S-GMA copolymer have been investigated.

Graft-copolymerization onto carbon black

International Nuclear Information System (INIS)

Nakase, Yoshiaki; Nishii, Masanobu; Kijima, Toshiyuki; Kato, Hiroshi.

1988-07-01

Radiation-induced graft copolymerization of vinyl monomer onto carbon black was performed. During the γ-ray- and electron beam-induced polymerization (In-source), or the electron beam post-polymerization, the graft-copolymerization behavior was affected by the kinds of both carbon blacks and monomers, i.e. the smaller the size of carbon black particles, the higher the apparent grafted fraction. Homopolymer in the grafted carbon black samples was washed out by the solvent of the polymer, and the extracted polymer seemed to be dimer or trimer of the used monomer. In the case of the post-polymerization with the pre-irradiation doses of 50 Mrad, homopolymer was hardly observed. The polymer sheets of plastics or rubbers with grafted carbon black had an electrical conductivity unalterable considerably by the heating cycles. The particles of grafted carbon black in the sheet might be kept much more at the surface layer within 100 nm depth than at the inner layer. (author)

Construction and optimization of an efficient breathing-based isothermal emulsion amplification method

Energy Technology Data Exchange (ETDEWEB)

Shen, Yanting, E-mail: shenyanting798@126.com [Research Center for Learning Science, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); State Key Laboratory of Bioelectronics, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Tian, Fei, E-mail: 642807827@qq.com [Research Center for Learning Science, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Tu, Jing, E-mail: jtu@seu.edu.cn [State Key Laboratory of Bioelectronics, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Li, Rui, E-mail: lirui901113@163.com [Research Center for Learning Science, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Chen, Zhenzhu, E-mail: zzchen_seu@163.com [Research Center for Learning Science, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Bai, Yunfei, E-mail: whitecf@seu.edu.cn [State Key Laboratory of Bioelectronics, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Ge, Qinyu, E-mail: geqinyu@seu.edu.cn [State Key Laboratory of Bioelectronics, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China); Lu, Zuhong, E-mail: zhlu@seu.edu.cn [State Key Laboratory of Bioelectronics, Southeast University, Sipailou Road no. 2, Nanjing, Jiangsu Province 210096 (China)

2017-06-22

The reaction temperature is one of the main factors that affect the stability of emulsion PCR (emPCR). Focusing on this point, we applied the “DNA breathing” mechanism in BEAMing (Bead, Emulsion, Amplification, and Magnetic) and proposed a more stable emulsion amplification method. Compared to the conventional emPCR, this method provided excellent results. Firstly, more stable emulsion system resulted in higher percentage of single-molecular amplifications (73.17%). Secondly, an ordinary temperature-controlling device was enough. Our outcome showed that the reaction temperature of this method was not strict so that the ordinary temperature-controlling device was enough for it (the heat block sets vs. the PCR instrument: 13.140 ± 0.110 vs. 13.008 ± 0.039, P = 0.120). Thirdly, the single-biotinylated emP{sub 1} coated streptavidin beads were stable enough to be used for this method (the control temperature vs. the reaction temperature: 2967.91 ± 409.045 vs. 3026.22 ± 442.129, P = 0.334), which could replace the double-biotinylated emP{sub 1} coated beads and was benefit for saving cost. In conclusion, the method presented here with stable emulsion system, simplified temperature-controlling device, and decreased investment would be a highly streamlined and inexpensive option for future single-molecular amplification based researches. - Highlights: • A breathing-based isothermal emulsion amplification (BIEA) method was developed. • BIEA showed excellent properties compared with conventional amplification method. • Terminal breathing of DNA duplex was firstly used in emulsion amplification.

Structural and behavioral characteristics of radiolytically synthesized polyacrylic acid–polyacrylonitrile copolymeric hydrogels

International Nuclear Information System (INIS)

Bera, Anuradha; Misra, R.K.; Singh, Shailendra K.

2013-01-01

Copolymeric hydrogels of polyacrylic acid (PAA) – polyacrylonitrile (PAN) was radiolytically synthesized from their respective monomers with trimethyloltrimethacrylate (TMPTMA) as the crosslinker wherein both polymerization and crosslinking could be achieved in a single step reaction using 60 Co γ-radiation under varying doses and dose rates. The formation of the hydrogels was confirmed by their FT-IR analysis, while their thermal degradation patterns were investigated through thermogravimetric analysis in both the dry and swelled state. The water sorption studies showed rapid swelling behavior of these hydrogels, where swelling (%EWC) was found to be strongly dependent on the ratio of the two monomers in the hydrogels and the swelling kinetics dependent on the dose rates of hydrogel synthesis. These radiolytically synthesized hydrogels responded to electrical stimulus both in terms of the bending speed as well as bending angle under an applied voltage. The nature of the deformation was reversible and can be controlled through switching the voltage on and off. - Highlights: • Polyacrylic acid – polyacrilonitrile copolymeric hydrogel has been radiolytically synthesized. • Trimethyloltrimethacrylate (TMPTMA) used as crosslinker. • Hydrogel has been characterized and tested for electroresponsive character. • Bending angles and bending speed were found dependent upon applied voltage

Recent advances in photoinduced donor/acceptor copolymerization

International Nuclear Information System (INIS)

Joensson, S.; Viswanathan, K.; Hoyle, C.E.; Clark, S.C.; Miller, C.; Morel, F.; Decker, C.

1999-01-01

Photoinitiated free radical polymerization of donor (D)/acceptor (A) type monomers has gained considerable interest due to the possibility to efficiently photopolymerize non-acrylate based systems. Furthermore, this photoinduced alternating copolymerization can be accomplished without the presence of a conventional free radical generating photoinitiator. In the past, we have shown that the structural influences in the direct photolysis of N-Alkyl and N-Arylmaleimides as well as their corresponding ground state charge transfer complexes (CTC) with suitable donors have carefully been investigated. For certain combinations of A and D type monomers, a direct photolysis of the ground state complex or the excitation of the acceptor, followed by the formation of an exciplex, has been shown to initiate the copolymerization. Herein, we show that the main route of initiation is based on inter or intra molecular H-abstraction from an excited state maleimide, whereby no exciplex formation takes place. H-abstraction will predominantly take place in systems where easily abstractable hydrogens are present. Our laser flash photolysis investigation, ESR (A. Hiroshi, I. Takasi, T. Nosi, Macromol. Chem. 190 (1989) 2821) and phosphorescence emissions (K.S. Chen, T. Foster, J.K.S. Wan, J. Phys. Chem. 84 (1980) 2473; C.J. Seliskar, S.P. McGlynn, J. Chem. Phys. 55 (1971) 4337) studies show that triplet excited states of N-alkyl substituted maleimides (RMI), which are well known strong precursors for direct H-abstractions from aliphatic ethers and secondary alcohols, are formed upon excitation. Rates of copolymerization and degrees of conversion for copolymerization of maleimide/vinyl ether pairs in air and nitrogen have been measured as a function of hydrogen abstractability of the excited triplet state MI as well as the influence of concentration and hydrogen donating effect of the hydrogen donor

Lithium aluminate spheroids prepared by emulsion procedure

International Nuclear Information System (INIS)

Mateos, A.G.; DiBello, P.M.; Zaleski, A.B.

1991-01-01

Lithium aluminate powders were prepared by emulsion evaporation method. The procedure involved preparation of water-in-oil emulsion, with the aqueous phase being a solution of Li and Al nitrates. The mixed salts precursor crystallized to gamma-LiAlO 2 at 700C. Single phase LiAlO 2 occurred as μm spherical particles with average crystallite size of 81 angstrom and surface area of 14 M 2 /g. After prolonged heating at 900C, the aluminate powder crystallite size grew by 5 times with a reduction in particle porosity. The emulsion technique promotes close control of particle size and shape of product and the technique facilitates chemical reaction of constituents and sinterability of resulting product

Modeling of emulsion copolymer microstructure

NARCIS (Netherlands)

van Doremaele, G.H.J.; Herk, van A.M.; German, A.L.

1992-01-01

A model is developed to describe stages II and III of batch emulsion copolymn., and its predictive capabilities are investigated by application to the system styrene-Me acrylate. The main reaction site is the monomer-swollen polymer particle. Copolymn. rate and copolymer microstructure (molar

Copolymerization of carbon monoxide and styrene catalyzed by resin-supported palladium polymer

Directory of Open Access Journals (Sweden)

2007-02-01

Full Text Available Polyketone was prepared by the copolymerization of carbon monoxide (CO and styrene (ST catalyzed by o-phenylenediamine resin-supported palladium acetate. Effects of each catalytic system component such as 2,2’-bipyridine, 1,4-quinone and p-toluene-sulphonate on the copolymerization were investigated. The resin-supported catalyst and the copolymerization product were characterized by infrared spectroscopy (IR, differential scanning calorimetry (DSC, thermogravimetry (TG, X-ray photoelectron spectroscopy (XPS, Scanning Electron Microscopy (SEM. Results indicated that the resin-supported catalyst has excellent catalytic property. Furthermore, partial catalytic activity was maintained after the catalyst was used for five times.

Chain chemical reactions during matrix devitrification

International Nuclear Information System (INIS)

Barkalov, I.M.

1980-01-01

Investigation results of chain reaction mechanisms, proceeding at devitrification of glass-like matrices under the effect of γ-irradiation are summarized. Peculiarities of kinetics and mechanism of chain reactions proceeding at devitrification are considered: hydrocarbon chlorination, polymerization of vinyl monomers, copolymerization and graft polymerization. Possible application aspects of the chain reaction conducting during matrix devitrification are also considered

GRAFT COPOLYMERIZATION OF OLYGOESTERACRYLATES WITH LIQUID RUBBER AND COPOLYMER’S CHARACTERISTICS

Directory of Open Access Journals (Sweden)

Y. A. Anisimov

2015-02-01

Full Text Available The kinetic of graft copolymerization of threeethyleneglicoldimethacrylate and di threeethyleneglicolftalatedimethacrylate with liquid buthadiene rubber have been studied as a function of the olygomers composition. The experimental constants of copolymerization rate and efficiency olygoesteracrylates graft to liquid rubber were determined. The ihfluence of olygoesteracrylates’ nature on the grafting efficiency to olygomer rubber is determined and the strength characteristics are found.

Thermosensitive copolymeric hydrogels with the regulated temperature of a phase transition

International Nuclear Information System (INIS)

Samchenko, Yu.M.; Konovalova, V.V.; Korotich, E.I.; Poltoratskaya, T.P.; Pobegaj, A.A.; Burban, A.F.; Ul'berg, Z.R.; Samchenko, Yu.M.; Konovalova, V.V.; Korotich, E.I.; Poltoratskaya, T.P.; Pobegaj, A.A.; Burban, A.F.; Ul'berg, Z.R.

2011-01-01

The work is devoted to the methods of obtaining the thermosensitive copolymeric hydrogels based on the NIPAAm with acrylic acid and its derivatives such as acrylamide, acrylonitrile, and methylacrylate. The mechanisms of thermoinitiated phase transitions in hydrogel matrices and the regularities of the thermoinitiated release of model compounds and drugs (aniline, novocaine, and sodium diclofenac) from copolymeric hydrogel are investigated.

Synthesis of copolymerized porous organic frameworks with high gas storage capabilities at both high and low pressures

KAUST Repository

Pei, Cuiying

2014-01-01

A series of copolymerized porous organic frameworks (C-POFs) were synthesized with monomers of tetrakis(4-bromophenyl)methane and tris(4-bromophenyl)amine in different ratios by a Yamamoto-type Ullmann cross-coupling reaction. These C-POFs exhibit high physicochemical stability, large surface areas and excellent H2, CH4 and CO 2 adsorption properties both at low and high pressures. This journal is © the Partner Organisations 2014.

Investigation of lipid oxidation and non-enzymatic browning reactions in marine PL emulsions

DEFF Research Database (Denmark)

Lu, Henna Fung Sieng; Nielsen, Nina Skall; Baron, Caroline P.

Marine phospholipids (PL) have received much attention recently due to their numerous advantages. One of these advantages is their better resistance towards oxidation as compared to fish oil. In addition to the antioxidative properties of α-tocopherol and phospholipids, the better oxidative...... stability of marine PL might be attributed to antioxidative properties of pyrroles formed between oxidised lipids with amine groups from phosphatidylethanolamine (PE) or residues amino acids that are present in marine PL. The main objective of this study was to investigate if the presence of amine group...... of amino acids (leucine, methionine and lysine) from 2 authentic standards (PC and PE) and 2 purified marine PL (LC and MPL) through sonication method. Emulsions were incubated at 60 ºC for 0, 2, 4 and 6 days. Non-enzymatic browning reactions were investigated through measurement of i) Strecker aldehydes...

Kinetics of vinyl acetate emulsion polymerization in a pulsed tubular reactor: comparison between experimental and simulation results

Directory of Open Access Journals (Sweden)

Sayer C.

2002-01-01

Full Text Available A new reactor, the pulsed sieve plate column (PSPC, was developed to perform continuous emulsion polymerization reactions. This reactor combines the enhanced flexibility of tubular reactors with the mixing behavior provided by sieved plates and by the introduction of pulses that is important to prevent emulsion destabilization. The main objective of this work is to study the kinetics of vinyl acetate (VA emulsion polymerization reactions performed in this PSPC. Therefore, both experimental studies and reaction simulations were performed. Results showed that it is possible to obtain high conversions with rather low residence times in the PSPC.

Study on radiation grafting reaction of MMA onto hydroxyapatite

International Nuclear Information System (INIS)

Jiang Bo

1996-01-01

The grafting reaction of MMA onto hydroxyapatite has been studied with the pre-irradiation method in air. The effects of radiation dose, monomer concentration, reaction temperature and inorganic acid on the system are observed. The grafting copolymerization is found to be controlled by the kinetics. If proper kinetic conditions are selected, a better grafting yield can be obtained. Employing weight method, burning method as well as SeM and IR analysis, it has been proved that MMA is definitely grafted onto hydroxyapatite by chemical bonds, which shows that it is possible to improve the interface of inorganic-organic composite materials and to make bioactive ceramics by using radiation induced-grafting copolymerization

Radiation induced graft copolymerization of jute fibre

International Nuclear Information System (INIS)

Al-Siddique, F.R.; Khan, A.U.; Sheikh, R.A.

1983-01-01

Graft copolymerized jute fibres (GCJF) were prepared by γ-ray induced graft copolymerization of various monomers onto bleached and de-waxed jute samples. The effect of γ-ray dose on the tendency of various monomers to form graft co-polymer was studied. It was found that the tendency decreases as follows: methylmethacrylate (MMA)>acrylonitrile (AN)>styrene (STY)>vinylacetate (VA). When the effect of monomer concentration on the formation of graft co-polymer was studied, it was found that a mixture of AN and STY gave a higher amount of grafting than what was observed for STY or AN alone, when used at a comparable concentration. A study on the effect of concentration of methyl alcohol (a swelling agent for jute) on the tendency of the monomers to form graft co-polymer showed that although there is no effect when only AN is used, an appreciable effect is observed if AN is mixed with STY. In the later case the tendency of graft co-polymerization increases with the increase of CH 3 OH concentration. It was further observed that the increase of CH 3 OH also has a positive influence on MMA to form graft co-polymer in the range of 40-90% CH 3 OH. The affinity of GCJF towards moisture has been found to decrease with the increase of polymer loading onto jute. The presence of swelling agents during graft copolymer formation was also found to decrease the affinity of GCJF towards moisture. (author)

Preparation of poly(BMA-co-MMA) particles by soap-free emulsion polymerization and its optical properties as photonic crystals.

Science.gov (United States)

Lee, Ki-Chang; Choo, Hun-Seung

2014-11-01

Narrowly dispersed poly(BMA-co-MMA) and PBMA latices with particle diameters ranging within 216-435 nm were synthesized successfully by surfactant-free emulsion polymerization with KPS and AIBA. The average particle diameter and particle size distribution, average molecular weight and its distribution, glass transition temperature, reflectance spectra in visible wavelength, and refractive indices for the respective poly(BMA-co-MMA) latices and their photonic crystals were systematically investigated in terms of BMA/MMA ratio, BMA content, polymerization temperature, and DVB effect. The rate of polymerization increased with increasing MMA concentration in BMA/MMA ratio. The particle diameter increased with BMA concentration in BMA/MMA ratio. The molecular weight increased with BMA concentration in BMA/MMA ratio and monomer concentration. The drying of the latices offered self-assembled shiny colloidal crystal films showing the characteristic structural colors in visible wavelength. All the poly(BMA-co-MMA) latices prepared in the study were fallen within the range of photonic grade microspheres. The reflectance measurement on the colloidal photonic crystals having different particle diameters clearly exhibited narrow stopbands. The reflection maxima (λ(max)) measured in this study were well close to the λ(max) calculated, derived from the Bragg's equation. The refractive indices of poly(BMA-co-MMA) photonic crystals were found to be almost same as the theoretical values and increased proportionally from 1.50 to 1.57 with BMA content in BMA/MMA ratios. It was, thus, found that the optical reflectance properties of the poly(BMA-co-MMA) colloidal photonic crystals can be controlled easily by adjusting the reaction conditions and BMA/MMA ratio in soap-free emulsion copolymerization of BMA and MMA.

Precise synthesis of thermoreversible block copolymers containing reactive furfuryl groups via living anionic polymerization: the countercation effect on block copolymerization behavior

Energy Technology Data Exchange (ETDEWEB)

Kang, Beom-Goo [ORNL; Pramanik, Nabendu [Indian Institute of Technology, Kharagpur; Singha, Nikhil K [ORNL; Lee, Jae-Suk [ORNL; Mays, Jimmy [University of Tennessee, Knoxville (UTK)

2015-08-07

The anionic block copolymerization of 4,4' -vinylphenyl-N,N-bis(4-tert-butylphenyl)benzenamine (A) with furfuryl isocyanate (B) was carried out using potassium naphthalenide (K-Naph) in tetrahydrofuran at -78 and -98 °C to prepare well-defined block copolymers containing furan groups for the formation of thermoreversible networks via a Diels Alder (DA) reaction. While no block copolymerization was observed in the absence of sodium tetraphenylborate (NaBPh₄) due to side reactions, well-defined poly-(B-b-A-b-B) (PBAB) copolymers with controlled molecular weights (M_n = 18 700 19 500 g mol ^-1) and narrow molecular weight distributions (M_w/M_n = 1.08 -1.17) were successfully synthesized in the presence of excess NaBPh₄. We prevented the occurrence of the undesirable side reactions during polymerization of B of NaBPh₄, which results in the change in the countercation from K⁺ to Na⁺ for further polymerization of B. Moreover, the cross-linking via the DA reaction between the furan groups of PBAB and bismaleimide was proved by FT-IR and differential scanning calorimetry (DSC), and the thermoreversible properties of the cross-linked polymer were subsequently investigated using DSC and solubility testing.

Electronically Stabilized Copoly(Styrene-Acrylic Acid Submicrocapsules Prepared by Miniemulsion Copolymerization

Directory of Open Access Journals (Sweden)

Minkwan Kim

2017-07-01

Full Text Available This work reports the preparation and characterization of poly(styrene-acrylic acid (St/AA submicrocapsules by using the miniemulsion copolymerization method. AA was introduced to miniemulsion polymerization of St to increase the zeta potential and the resulting electrostatic stability of St/AA submicrocapsules. Phytoncide oil was adopted as the core model material. Miniemulsion copolymerization of St and AA was conducted at a fixed monomer concentration (0.172 mol with a varying monomer feed ratio [AA]/[St] (0.2, 0.25, 0.33, 0.5, and 1.0. Concentrations of initiator (azobisisobutyronitrile; 1.0 × 10−3, 2.0 × 10−3, 3.0 × 10−3, and 4.0 × 10−3 mol/mol of monomer and surfactant (sodium dodecyl sulfate; 0.6 × 10−3, 1.0 × 10−3, and 1.4 × 10−3 mol were also controlled to optimize the miniemulsion copolymerization of St and AA. Dynamic light scattering and microscopic analyses confirmed the optimum condition of miniemulsion copolymerization of St and AA. Long-term colloidal stability of aqueous St/AA submicrocapsule suspension was evaluated by using TurbiscanTM Lab. In this work, the optimum condition for miniemulsion copolymerization of St and AA was determined ([AA]/[St] = 0.33; [SDS] = 1.0 × 10−3 mol; [AIBN] = 2.0 × 10−3 mol/mol of monomer. St/AA submicrocapsules prepared at the optimum condition (392.6 nm and −55.2 mV of mean particle size and zeta potential, respectively showed almost no variations in backscattering intensity (stable colloids without aggregation.

Development of High Sensitivity Nuclear Emulsion and Fine Grained Emulsion

Science.gov (United States)

Kawahara, H.; Asada, T.; Naka, T.; Naganawa, N.; Kuwabara, K.; Nakamura, M.

2014-08-01

Nuclear emulsion is a particle detector having high spacial resolution and angular resolution. It became useful for large statistics experiment thanks to the development of automatic scanning system. In 2010, a facility for emulsion production was introduced and R&D of nuclear emulsion began at Nagoya university. In this paper, we present results of development of the high sensitivity emulsion and fine grained emulsion for dark matter search experiment. Improvement of sensitivity is achieved by raising density of silver halide crystals and doping well-adjusted amount of chemicals. Production of fine grained emulsion was difficult because of unexpected crystal condensation. By mixing polyvinyl alcohol (PVA) to gelatin as a binder, we succeeded in making a stable fine grained emulsion.

Whey protein isolate modified by transglutaminase aggregation and emulsion gel properties

Science.gov (United States)

Qi, Weiwei; Chen, Chong; Liu, Mujun; Yu, Guoping; Cai, Xinghang; Guo, Peipei; Yao, Yuxiu; Mei, Sijie

2015-07-01

Whey protein isolate and commercial soybean salad oil were used to produce the WPI emulsion dispersions. The properties of TG-catalyzed emulsion gelation produced from WPI emulsion dispersions were investigated by the amount of TG, temperature, pH and reaction time. Specifically, the texture properties (hardness and springiness), water-holding capacity and rheological properties (G' and G") were assessed. The result of Orthogonal tests showed WPI emulsion can form better hardness and springiness gel when the ratio of TG and WPI was 20U/g, pH 7.5, treatment temperature and time were 50°C and 3 h, respectively. The microstructure of TG emulsion gels was more compact, gel pore is smaller, distribution more uniform, the oil droplets size smaller compared with untreated emulsion gels. Compared to the control of rheological properties, G' and G" were significantly increased and G' > G", results showed that the gel was solid state, and TG speeded up the process of gelation.

Kinetics and thermodynamics of first-order Markov chain copolymerization

Energy Technology Data Exchange (ETDEWEB)

Gaspard, P.; Andrieux, D. [Center for Nonlinear Phenomena and Complex Systems, Université Libre de Bruxelles, Code Postal 231, Campus Plaine, B-1050 Brussels (Belgium)

2014-07-28

We report a theoretical study of stochastic processes modeling the growth of first-order Markov copolymers, as well as the reversed reaction of depolymerization. These processes are ruled by kinetic equations describing both the attachment and detachment of monomers. Exact solutions are obtained for these kinetic equations in the steady regimes of multicomponent copolymerization and depolymerization. Thermodynamic equilibrium is identified as the state at which the growth velocity is vanishing on average and where detailed balance is satisfied. Away from equilibrium, the analytical expression of the thermodynamic entropy production is deduced in terms of the Shannon disorder per monomer in the copolymer sequence. The Mayo-Lewis equation is recovered in the fully irreversible growth regime. The theory also applies to Bernoullian chains in the case where the attachment and detachment rates only depend on the reacting monomer.

Effects of NOx-inhibitor agent on fuel properties of three-phase biodiesel emulsions

International Nuclear Information System (INIS)

Lin, Cherng-Yuan; Lin, Hsiu-An

2008-01-01

Biodiesel is one of the more promising alternative clean fuels to fossil fuel, which can reduce the emissions of fossil fuel burning, and possibly resolve the energy crisis caused by the exhaustion of petroleum resources in the near future. The burning of biodiesel emits much less gaseous emissions and particulate matter primarily because of its dominant combustion efficiency. However, the high oxygen content in biodiesel not only promotes the burning process but also enhances NO x formation when biodiesel is used as fuel. Biodiesel emulsion and the additive of NO x -inhibitor agent are considered to reduce levels of NO x emissions in this experimental study. The biodiesel was produced by transesterification reaction accompanied with peroxidation process. A three-phase biodiesel emulsion of oil-in water drops-in oil (O/W/O) and an O/W/O biodiesel emulsion containing aqueous ammonia were prepared afterwards. The effect of the existence of NO x -inhibitor agent on the fuel properties and the emulsion characteristics of the O/W/O biodiesel emulsions were investigated. The experimental results show that the burning of the O/W/O biodiesel emulsion and the O/W/O biodiesel emulsion containing aqueous ammonia had larger fraction of fuel burnt and thus larger heat release than the neat biodiesel if water content is not considered for the calculation of heating value. The addition of aqueous ammonia within the dispersed phase of the O/W/O biodiesel emulsion appeared to deteriorate the emulsification characteristics. A smaller quantity of emulsion and greater kinematic viscosity were formed while a larger carbon residue and actual reaction-heat release also appeared for this O/W/O biodiesel emulsion. Aqueous ammonia in the O/W/O biodiesel emulsion produces a higher pH value as well. In addition, the number as well as the volumetric fraction of the dispersed water droplets is reduced for the O/W/O biodiesel emulsion that contains aqueous ammonia. (author)

Development of High Sensitivity Nuclear Emulsion and Fine Grained Emulsion

International Nuclear Information System (INIS)

Kawahara, H.; Asada, T.; Naka, T.; Naganawa, N.; Kuwabara, K.; Nakamura, M.

2014-01-01

Nuclear emulsion is a particle detector having high spacial resolution and angular resolution. It became useful for large statistics experiment thanks to the development of automatic scanning system. In 2010, a facility for emulsion production was introduced and R and D of nuclear emulsion began at Nagoya university. In this paper, we present results of development of the high sensitivity emulsion and fine grained emulsion for dark matter search experiment. Improvement of sensitivity is achieved by raising density of silver halide crystals and doping well-adjusted amount of chemicals. Production of fine grained emulsion was difficult because of unexpected crystal condensation. By mixing polyvinyl alcohol (PVA) to gelatin as a binder, we succeeded in making a stable fine grained emulsion

Synthesis and characterization of high molecular weight hydrophobically modified polyacrylamide nanolatexes using novel nonionic polymerizable surfactants

Directory of Open Access Journals (Sweden)

A.M. Al-Sabagh

2013-12-01

Full Text Available In this article, nine hydrophobically modified polyacrylamides (HM-PAM nanolatexes, were synthesized by copolymerizing the acrylamide monomer and novel polymerizable surfactants (surfmers. The reaction was carried out by inverse microemulsion copolymerization technique. The copolymerization was initiated by redox initiators composed of potassium peroxodisulphate and sodium bisulfite. The emulsion was stabilized using mixed tween 85 and span 80 as nonionic emulsifiers. The prepared HM-PAMs were classified into three groups according to the surfmers used in the copolymerization. The chemical structures of the prepared HM-PAMs were confirmed by FT-IR, 1H NMR and 13C NMR. The thermal properties were estimated with the thermal gravimetric analysis (TGA. The size and morphology of the prepared latexes were investigated by the dynamic light scattering (DLS and the High Resolution Transmission Electron Microscope (HRTEM. Finally, the molecular weights of the prepared copolymers were determined by the GPC and the viscosity average molecular weight method. They were situated between 1.58 × 106 and 0.89 × 106.

Radiation-induced copolymerization of methyl trifluoroacrylate with α-olefins

International Nuclear Information System (INIS)

Matsuda, O.; Watanabe, T.; Tabata, Y.; Machi, S.

1978-01-01

Paper describes the radiation-induced bulk copolymerization of methyl trifluoroacrylate with various α olefins; propylene, 1-butene, 1-pentene, 1-hexene, 1-octene, and isobutylene. MTFA (purity above 98%) was synthesized by method described in literature. Reagent grade α-olefins were used. An equimolar mixture of MTFA and α-olefin was charged into the reactor. Trace amounts of oxygen were purged by the freeze-thaw technique. Irradiation was carried out with gamma rays from a 60 Co source under vapor pressure of the monomers at 25 0 C. The product was precipitated and washed with methanol to remove unreacted monomers, and dried under vacuum at 60 0 C. Infrared spectra of the copolymers were measured; compositions were determined from elemental analysis. Reactivity of the α-olefins appears to be related to the electron density at the double bond. All copolymers were found to have almost equimolar compositions and were soluble in polar solvents such as tetrahydrofuran and acetone. Copolymerization was inhibited completely by the addition of 1,1-diphenyl-2-picrihydrazil, but not by water, indicating that the copolymerization proceeds via a radical mechanism. 1 table; 2 figures

Irradiation and development of the nuclear emulsions exposed to intense fluxes of thermal neutrons with {gamma} rays; Irradiation et developpement des emulsions nucleaires exposees a des flux intenses de neutrons thermiques, accompagnes de rayons {gamma}

Energy Technology Data Exchange (ETDEWEB)

Faraggi, H; Bonnet, A; Cohen, J [Commissariat a l' Energie Atomique, Lab. du Fort de Chatillon, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1952-07-01

The thermal neutron fluxes provided by nuclear reactors permit the survey of relatively rare phenomenons, and dosage of very weak quantities of some elements. One of the most favorable detection technique are constituted by the use of the nuclear emulsions. one can mention: - the dosage of uranium by counting in the emulsion the number of traces due to fission fragments after irradiation. - The dosage of the lithium and the boron as trace amounts with the help of nuclear reactions (n, {alpha}) and thermal neutrons. - The research of reactions (n, {alpha}) or (n, p) of very weak cross section for middle or heavy elements. These different applications require however important neutrons fluxes. It had therefore obliged us to search for the most favorable irradiation and development of the emulsions conditions, to get the best visibility of the trajectories and decrease the phenomena of fog on the emulsion, which prevents any observation. (M.B.) [French] Les flux de neutrons thermiques fournis par les reacteurs nucleaires permettent l'etude de phenomenes relativement rares, et le dosage de tres faibles quantites de certains elements. Un des moyens de detection les plus favorables est constitue par l'utilisation des emulsions nucleaires. on peut citer: - le dosage de l'uranium par comptage dans l'emulsion du nombre de traces dues aux fragments de fission apres irradiation. - Le dosage du lithium et du bore a l'etat de traces a l'aide des reactions (n, {alpha}) sous l'action des neutrons thermiques. - La recherche de reactions (n,{alpha}) ou (n,p) de tres faible section efficace pour des elements moyens ou lourds. Ces differentes applications necessite cependant des flux de neutrons important. On a donc ete amene a rechercher les conditions les plus favorables d'irradiation et de developpement des emulsions, de maniere a obtenir la meilleure visibilite des trajectoires et diminuer les phenomenes de voile de l'emulsion, qui empeche toute observation. (M.B.)

Irradiation and development of the nuclear emulsions exposed to intense fluxes of thermal neutrons with {gamma} rays; Irradiation et developpement des emulsions nucleaires exposees a des flux intenses de neutrons thermiques, accompagnes de rayons {gamma}

Energy Technology Data Exchange (ETDEWEB)

Faraggi, H.; Bonnet, A.; Cohen, J. [Commissariat a l' Energie Atomique, Lab. du Fort de Chatillon, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1952-07-01

The thermal neutron fluxes provided by nuclear reactors permit the survey of relatively rare phenomenons, and dosage of very weak quantities of some elements. One of the most favorable detection technique are constituted by the use of the nuclear emulsions. one can mention: - the dosage of uranium by counting in the emulsion the number of traces due to fission fragments after irradiation. - The dosage of the lithium and the boron as trace amounts with the help of nuclear reactions (n, {alpha}) and thermal neutrons. - The research of reactions (n, {alpha}) or (n, p) of very weak cross section for middle or heavy elements. These different applications require however important neutrons fluxes. It had therefore obliged us to search for the most favorable irradiation and development of the emulsions conditions, to get the best visibility of the trajectories and decrease the phenomena of fog on the emulsion, which prevents any observation. (M.B.) [French] Les flux de neutrons thermiques fournis par les reacteurs nucleaires permettent l'etude de phenomenes relativement rares, et le dosage de tres faibles quantites de certains elements. Un des moyens de detection les plus favorables est constitue par l'utilisation des emulsions nucleaires. on peut citer: - le dosage de l'uranium par comptage dans l'emulsion du nombre de traces dues aux fragments de fission apres irradiation. - Le dosage du lithium et du bore a l'etat de traces a l'aide des reactions (n, {alpha}) sous l'action des neutrons thermiques. - La recherche de reactions (n,{alpha}) ou (n,p) de tres faible section efficace pour des elements moyens ou lourds. Ces differentes applications necessite cependant des flux de neutrons important. On a donc ete amene a rechercher les conditions les plus favorables d'irradiation et de developpement des emulsions, de maniere a obtenir la meilleure visibilite des trajectoires et diminuer les phenomenes de voile de l'emulsion, qui

On-line monitoring and composition control of the emulsion copolymerization of VeoVA 9 and butyl acrylate by Raman spectroscopy

NARCIS (Netherlands)

van den Brink, H.J.T.; Pepers, M.L.H.; Herk, van A.M.; German, A.L.

2001-01-01

The batch and semi-continuous emulsion copolymn. of Bu acrylate and vinyl neononanoate (VeoVA 9) were monitored by remote online Raman spectroscopy. Monomer concns. were calcd. in real-time by a classical least squares (CLS) approach using the vinyl regions of the Raman spectra. During the batch

Cation-exchanger fabric prepared by electron beam - induced graft copolymerization of binary monomer mixture

International Nuclear Information System (INIS)

Bondar, Yu.V.; Kim, H.J.; Lim, Y.J.; Perelygin, V.P.

2004-01-01

Applying the electron-beam preirradiation method in air the sorption-active polypropylene fiber, containing sulfonic acid (R-SO 3 H) groups, was prepared by simultaneous graft copolymerization of sodium styrenesulfonate with acrylic acid in water solution. The effect of reaction conditions on the grafting yield and reaction mechanism was examined. It was found that the received CEF contains groups of strong acid (R-SO 3 H) and weak acid (R-COOH) in almost equal proportion. The ion-exchange properties of the CEF towards Cu(II) and Co(II) ions were investigated depending on the form of the CEF and a pH of the solution. It was shown that the utilization of the CEF in Na- form allows to make the best use of its ion-exchange capacity. (author)

X-ray structure determination of new monomers to establish their polymerizability: copolymerization of two tetrasubstituted electrophilic olefins with electron-rich styrenes giving polymers with an average 1.25 functional groups per chain carbon atom

International Nuclear Information System (INIS)

Hall, H.K. Jr.; Reineke, K.E.; Ried, J.H.; Sentman, R.C.; Miller, D.

1982-01-01

X-ray crystal structure determination for two tetrasubstituted electrophilic olefins, tetramethyl ethylenetetracarboxylate TMET and dimethyl dicyanofumarate DDCF, revealed two fundamentally different molecular structures. TMET is a nonplanar molecule that possesses two opposite ester groups planar and the others above and below the molecular plane. In contrast, DDCF is a molecule for which both ester groups lie in the plane of the double bond and nitrile groups. DDCF underwent thermal spontaneous copolymerization with electron-rich styrenes to give 1:1 alternating copolymers in moderate yields and molecular weights. These copolymers, which result from the first copolymerization of a tetrasubstituted olefin, possess an average functionality of 1.25 per chain carbon atom. Polymerization is made possible by low steric hindrance and the high delocalization in the propagating radical. The yields were limited by competing cycloaddition reaction. The corresponding diethyl ester also copolymerized, but not so well. Neither electrophilic olefin homopolymerized under γ-irradiation. TMET did not copolymerize at all when treated under identical conditions

Determination of Monomers Reactivity Ratios in Ethyl Acrylate-Methacrylic Acid Copolymerization by Off-Line 1H NMR

Directory of Open Access Journals (Sweden)

Samaneh Ashenagar

2017-03-01

Full Text Available The physical, chemical and mechanical properties of polymer systems depend on the micro-structural characteristics of their macromolecular chains. Along with the most characteristic kinetic parameters in copolymerization reactions are the reactivity ratios, which give a clear idea of the average composition and the monomer sequence distribution in copolymer systems. This research studies the solution radical copolymerization of methacrylic acid (MAA-ethyl acrylate (EA system at low conversion with 2,2'-azobisisobutyronitrile (AIBN as thermal initiator at 60°C in deuterated dimethyl sulfoxide (DMSO-d6 as a reaction solvent. In this case, the monomer reactivity ratios were determined using linear off-line 1H nuclear magnetic resonance spectroscopy (1H NMR methods such as Mayo-Louis, Finemann-Ross, Inverted Finemann-Ross , Ezrielev-Brokhina-Roskin, Joshi-Joshi, Kelen-Tudos, extended Kelen- Tudos, Mao-Huglin at low and high conversions. The next estimation process in off-line 1H NMR methods were performed by applying techniques based on ordinary least square (OLS and generalized least square (GLS. The results showed that the GLS approach compared to the OLS increased regression coefficients (R2 and the order of magnitude of parameter variances obtained from GLS was many times lower than that obtained from OLS. In addition, the monomer reactivity ratios obtained by the Mao-Huglin method and the GLS approach showed the best linear estimation.

Alternating copolymerization of propylene oxide with biorenewable terpene-based cyclic anhydrides: a sustainable route to aliphatic polyesters with high glass transition temperatures.

Science.gov (United States)

Van Zee, Nathan J; Coates, Geoffrey W

2015-02-23

The alternating copolymerization of propylene oxide with terpene-based cyclic anhydrides catalyzed by chromium, cobalt, and aluminum salen complexes is reported. The use of the Diels-Alder adduct of α-terpinene and maleic anhydride as the cyclic anhydride comonomer results in amorphous polyesters that exhibit glass transition temperatures (Tg ) of up to 109 °C. The polymerization conditions and choice of catalyst have a dramatic impact on the molecular weight distribution, the relative stereochemistry of the diester units along the polymer chain, and ultimately the Tg of the resulting polymer. The aluminum salen complex exhibits exceptional selectivity for copolymerization without transesterification or epimerization side reactions. The resulting polyesters are highly alternating and have high molecular weights and narrow polydispersities. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bis(formylphenolatocobalt(II-Mediated Alternating Radical Copolymerization of tert-Butyl 2-Trifluoromethylacrylate with Vinyl Acetate

Directory of Open Access Journals (Sweden)

Sanjib Banerjee

2017-12-01

Full Text Available The organometallic-mediated radical polymerization (OMRP of vinyl acetate (VAc and its OMR copolymerization (OMRcoP with tert-butyl 2-trifluoromethylacrylate (MAF-TBE mediated by Co(SAL2 (SAL = 2-formylphenolato or deprotonated salicylaldehyde produced relatively well-defined PVAc and poly(VAc-alt-MAF-TBE copolymers at moderate temperature (<40 °C in bulk. The resulting alternating copolymer was characterized by 1H-, 13C- and 19F-nuclear magnetic resonance (NMR spectroscopies, and by size exclusion chromatography. The linear first-order kinetic plot, the linear evolutions of the molar mass with total monomer conversion, and the relatively low dispersity (Đ~1.55 of the resulting copolymers suggest that this cobalt complex provides some degree of control over the copolymerization of VAc and MAF-TBE. Compared to the previously investigated cobalt complex OMRP mediators having a fully oxygen-based first coordination sphere, this study emphasizes a few peculiarities of Co(SAL2: a lower ability to trap radical chains as compared to Co(acac2 and the absence of catalytic chain transfer reactions, which dominates polymerizations carried in the presence of 9-oxyphenalenone cobalt derivative.

Preparation and Application of Water-in-Oil Emulsions Stabilized by Modified Graphene Oxide

Directory of Open Access Journals (Sweden)

Xiaoma Fei

2016-08-01

Full Text Available A series of alkyl chain modified graphene oxides (AmGO with different alkyl chain length and content was fabricated using a reducing reaction between graphene oxide (GO and alkyl amine. Then AmGO was used as a graphene-based particle emulsifier to stabilize Pickering emulsion. Compared with the emulsion stabilized by GO, which was oil-in-water type, all the emulsions stabilized by AmGO were water-in-oil type. The effects of alkyl chain length and alkyl chain content on the emulsion properties of AmGO were investigated. The emulsions stabilized by AmGO showed good stability within a wide range of pH (from pH = 1 to pH = 13 and salt concentrations (from 0.1 to 1000 mM. In addition, the application of water-in-oil emulsions stabilized by AmGO was investigated. AmGO/polyaniline nanocomposite (AmGO/PANi was prepared through an emulsion approach, and its supercapacitor performance was investigated. This research broadens the application of AmGO as a water-in-oil type emulsion stabilizer and in preparing graphene-based functional materials.

Transglutaminase catalyzed cross-linking of sodium caseinate improves oxidative stability of flaxseed oil emulsion.

Science.gov (United States)

Ma, Hairan; Forssell, Pirkko; Kylli, Petri; Lampi, Anna-Maija; Buchert, Johanna; Boer, Harry; Partanen, Riitta

2012-06-20

Sodium caseinate was modified by transglutaminase catalyzed cross-linking reaction prior to the emulsification process in order to study the effect of cross-linking on the oxidative stability of protein stabilized emulsions. The extent of the cross-linking catalyzed by different dosages of transglutaminase was investigated by following the ammonia production during the reaction and using SDS-PAGE gel. O/W emulsions prepared with the cross-linked and non-cross-linked sodium caseinates were stored for 30 days under the same conditions. Peroxide value measurement, oxygen consumption measurement, and headspace gas chromatography analysis were used to study the oxidative stability of the emulsions. The emulsion made of the cross-linked sodium caseinate showed an improved oxidative stability with reduced formation of fatty acid hydroperoxides and volatiles and a longer period of low rate oxygen consumption. The improving effect of transglutaminase catalyzed cross-linking could be most likely attributed to the enhanced physical stability of the interfacial protein layer against competitive adsorption by oil oxidation products.

Influence of Steam Injection and Water-in-Oil Emulsions on Diesel Fuel Combustion Performance

Science.gov (United States)

Sung, Meagan

Water injection can be an effective strategy for reducing NOx because water's high specific heat allows it to absorb heat and lower system temperatures. Introducing water as an emulsion can potentially be more effective at reducing emissions than steam injection due to physical properties (such as microexplosions) that can improve atomization and increase mixing. Unfortunately, the immiscibility of emulsions makes them difficult to work with so they must be mixed properly. In this effort, a method for adequately mixing surfactant-free emulsions was established and verified using high speed cinematography. As the water to fuel mass ratio (W/F) increased, emulsion atomization tests showed little change in droplet size and spray angle, but a shorter overall breakup point. Dual-wavelength planar laser induced fluorescence (D-PLIF) patternation showed an increase in water near the center of the spray. Steam injection flames saw little change in reaction stability, but emulsion flames experienced significant losses in stability that limited reaction operability at higher W/F. Emulsions were more effective at reducing NOx than steam injection, likely because of liquid water's latent heat of vaporization and the strategic injection of water into the flame core. OH* chemiluminescence showed a decrease in heat release for both methods, though the decrease was greater for emulsions. Both methods saw decreases in flame length for W/F 0.15. Lastly, flame imaging showed a shift towards a redder appearance with the addition or more water, as well as a reduction in flame flares.

Acquisition of Co metal from spent lithium-ion battery using emulsion liquid membrane technology and emulsion stability test

Science.gov (United States)

Yuliusman; Wulandari, P. T.; Amiliana, R. A.; Huda, M.; Kusumadewi, F. A.

2018-03-01

Lithium-ion batteries are the most common type to be used as energy source in mobile phone. The amount of lithium-ion battery wastes is approximated by 200 – 500 ton/year. In one lithium-ion battery, there are 5 – 20% of cobalt metal, depend on the manufacturer. One of the way to recover a valuable metal from waste is leaching process then continued with extraction, which is the aim of this study. Spent lithium-ion batteries will be characterized with EDX and AAS, the result will show the amount of cobalt metal with form of LiCoO2 in the cathode. Hydrochloric acid concentration used is 4 M, temperature 80°C, and reaction time 1 hour. This study will discuss the emulsion stability test on emulsion liquid membrane. The purpose of emulsion stability test in this study was to determine optimum concentration of surfactant and extractant to produce a stable emulsion. Surfactant and extractant used were SPAN 80 and Cyanex 272 respectively with both concentrations varied. Membrane and feed phase ratios used in this experiment was 1 : 2. The optimum results of this study were SPAN 80 concentrations of 10% w/v and Cyanex 272 0.7 M.

TUNG OIL BASED MONOMER FOR THERMOSETTING POLYMERS: SYNTHESIS, CHARACTERIZATION AND COPOLYMERIZATION WITH STYRENE

Directory of Open Access Journals (Sweden)

Chengguo Liu,

2011-11-01

Full Text Available A tung oil (TO based monomer for rigid thermosetting polymer was synthesized, characterized, and copolymerized with styrene in this study. Tung oil was alcoholyzed with pentaerythritol (PER to get tung oil pentaerythritol alcoholysis products (TOPER, and the optimized conditions were explored according to the yields of TOPER analyzed by gas chromatography-mass spectrometry (GC-MS. The resulting alcoholysis products were maleinated to form tung oil maleate half ester (TOPERMA, and the reaction conditions were determined by monitoring the reaction extents of TOPER and maleic anhydride (MA with 1HNMR spectroscopy. The TO alcoholysis and maleinization reaction products were characterized by IR, 1HNMR, and electrospray ionization-mass spectrometry (ESI-MS techniques. At last, the TOPERMA mixture was cured with styrene (St, and the initiator tert-butyl peroxy benzoate (TPB. Differential scanning calorimetry (DSC was employed to characterize the curing process. Mechanical properties of the cured TOPERMA/St resin further confirmed the best procedure for the maleinization reaction. The loading of TO reached about 30% weight of the resulting thermosetting polymer. This promising material from renewable resources can be a potential substitution for petroleum products when used as sheet molding compounds.

Mechanistic aspects of the metal catalyzed alternating copolymerization of epoxides and carbon monoxide.

Science.gov (United States)

Allmendinger, Markus; Molnar, Ferenc; Zintl, Manuela; Luinstra, Gerrit A; Preishuber-Pflügl, Peter; Rieger, Bernhard

2005-09-05

The cobalt-catalyzed alternating copolymerization of epoxides and CO is a novel, direct approach to aliphatic polyesters, such as poly(hydroxybutyrate) (PHB). This reaction was found to be catalyzed by Ph3Si[Co(CO)4] (4) and pyridine affording in a first step the stable mono-insertion product Ph3Si-O-CH(CH3)-CH2-CO-Co(CO)4 (5). However, a profound mechanistic understanding, especially of the role of pyridine as the key component for the polymerization reaction was missing. ATR-IR online monitoring under catalytic conditions and DFT calculations were used to show that an acylpyridinium cation is formed by cleavage of the cobalt-acyl bond of 5 in the presence of pyridine. The Lewis acid thus generated activates the next incoming epoxide monomer for ring opening through [Co(CO)4]-. The catalytic cycle is completed by a subsequent CO insertion in the new cobalt-alkyl bond. The calculations are used to explore the energetic hypersurface of the polymerization reaction and are complemented by extended experimental investigations that also support the mechanistic hypotheses.

Recent Emulsion Technologies

International Nuclear Information System (INIS)

Ariga, A.

2011-01-01

Emulsion technologies are very much developed in the last decade and still developing in both the emulsion gel and the data taking. Emulsion detectors are suitable for the neutrino experiments because they can distinguish all 3 flavors of neutrino. The OPERA experiment, a recent pillar in the emulsion experiments aiming at the first observation of the neutrino oscillation in CNGS beam in appearance mode, is running, showing the good capability to separate 3 flavor neutrino interactions. In this poster, the recent developments and prospects of the emulsions for the next generation experiments are reported.

Nuclear emulsion experiments on particle production at high energies

International Nuclear Information System (INIS)

Otterlund, I.

1976-08-01

Various experimental results, including multiplicities of shower-particles and heavy prong particles, correlations between them and single particle distributions, from proton-emulsion nucleus reactions in the energy range 200-400 GeV are presented. (Auth.)

Constrained Geometry Organotitanium Catalysts Supported on Nanosized Silica for Ethylene (co)Polymerization.

Science.gov (United States)

Li, Kuo-Tseng; Wu, Ling-Huey

2017-05-05

Supported olefin polymerization catalysts can prevent reactor-fouling problems and produce uniform polymer particles. Constrained geometry complexes (CGCs) have less sterically hindered active sites than bis-cyclopentadienyl metallocene catalysts. In the literature, micrometer-sized silica particles were used for supporting CGC catalysts, which might have strong mass transfer limitations. This study aims to improve the activity of supported CGC catalysts by using nanometer-sized silica. Ti[(C₅Me₄)SiMe₂(N t Bu)]Cl₂, a "constrained-geometry" titanium catalyst, was supported on MAO-treated silicas (nano-sized and micro-sized) by an impregnation method. Ethylene homo-polymerization and co-polymerization with 1-octene were carried out in a temperature range of 80-120 °C using toluene as the solvent. Catalysts prepared and polymers produced were characterized. For both catalysts and for both reactions, the maximum activities occurred at 100 °C, which is significantly higher than that (60 °C) reported before for supported bis-cyclopentadienyl metallocene catalysts containing zirconium, and is lower than that (≥140 °C) used for unsupported Ti[(C₅Me₄)SiMe₂(N t Bu)]Me₂ catalyst. Activities of nano-sized catalyst were 2.6 and 1.6 times those of micro-sized catalyst for homopolymerization and copolymerization, respectively. The former produced polymers with higher crystallinity and melting point than the latter. In addition, copolymer produced with nanosized catalyst contained more 1-octene than that produced with microsized catalyst.

Stabilization of oil-in-water emulsions by enzyme catalyzed oxidative gelation of sugar beet pectin

DEFF Research Database (Denmark)

Abang Zaidel, Dayang Norulfairuz; Chronakis, Ioannis S.; Meyer, Anne S.

2013-01-01

Enzyme catalyzed oxidative cross-linking of feruloyl groups can promote gelation of sugar beet pectin (SBP). It is uncertain how the enzyme kinetics of this cross-linking reaction are affected in emulsion systems and whether the gelation affects emulsion stability. In this study, SBP (2.5% w...... larger average particle sizes than the emulsions in which the SBP was homogenized into the emulsion system during emulsion preparation (referred as Mix B). Mix B type emulsions were stable. Enzyme catalyzed oxidative gelation of SBP helped stabilize the emulsions in Mix A. The kinetics of the enzyme...... catalyzed oxidative gelation of SBP was evaluated by small angle oscillatory measurements for horseradish peroxidase (HRP) (EC 1.11.1.7) and laccase (EC 1.10.3.2) catalysis, respectively. HRP catalyzed gelation rates, determined from the slopes of the increase of elastic modulus (G0) with time, were higher...

Relativistic alpha-particles emitted in Fe-emulsion interactions at 1.7 A GeV

International Nuclear Information System (INIS)

Bhalla, K.B.; Chaudhry, M.; Lokanathan, S.; Grover, R.K.; Daftari, I.K.; Mangotra, L.L.; Rao, N.K.; Garpman, S.; Otterlund, I.

1981-02-01

Relativistic α-particles have been studied in 423 Fe-emulsion interactions at 1.7 A Gev. Comparisons of the observed angular distribution with that from 16 O-emulsion reactions at 2.1 A GeV reveal that more α particles are observed at large angles in the Fe-emulsion reactions. The α particles with large angles connot be explained by fragmentation from a clean cut spectator. Comparison of the experimental data with moving relativistic Boltzmann distributions shows that a single Boltzmann distribution cannot fit the fragmentation peak and the tail simultaneously. A thermal source (fireball) explaining the tail part of the distribution need to be formed by a mechanism other than simple clean cut participant-spectator picture. A large transverse momentum transfer to spectator before fragmentation may explain the tail. (author)

Continuous emulsion copolymerisation of styrene and methyl acrylate

NARCIS (Netherlands)

Boomen, van den F.H.A.M.; Meuldijk, J.; Thoenes, D.

1996-01-01

For emulsion polymerisation the reactor type has a strong influence on the final product properties, for example the particle size (distribution) and the polymer composition. A batch copolymerisation of styrene and methyl acrylate shows strong composition drift. The course of the batch reaction has

Efeitos da temperatura e do tipo de iniciador na redução do teor de monômero residual durante reações de copolimerização em emulsão Effects of temperature and type of initiators on the reduction of residual monomer content in emulsion copolymerization reactions

Directory of Open Access Journals (Sweden)

Wilson H. Hirota

2004-03-01

Full Text Available Reduzir o teor de monômero residual é uma preocupação de qualquer produtor de polímeros, pois produtos sem, ou com teores muito baixos de monômero residual, apresentam um apelo comercial diferenciado. Neste trabalho são apresentadas e testadas experimentalmente diversas estratégias para reduzir o teor de monômero residual de copolímeros estireno/acrilato de butila produzidos em reações semicontínuas de polimerização em emulsão, que são amplamente utilizados nas indústrias de papel e tintas. Estas estratégias envolvem a adição contínua de iniciador e/ou o aumento da temperatura do reator durante a última etapa da reação, além da adição de um agente redutor e/ou de um iniciador solúvel na fase orgânica. Verificou-se que a combinação adequada de diferentes técnicas pode levar a uma redução significativa no teor residual de monômeros no látex.Reducing the residual monomer content is a major concern of every polymer producer, as products with no, or very low levels of residual monomer have a marked commercial appeal. Styrene / butyl acrylate copolymers produced in emulsion polymerization reactions are widely applied in paper and paint industries. In this work, several strategies to reduce the residual monomer content of styrene and butyl acrylate copolymers produced in semicontinuous emulsion polymerization reactions are presented and tested. These strategies involve the continuous addition of initiator, increasing the reaction temperature during the last stage of the reaction, and adding a reducing agent or an initiator that is soluble in the organic phase at this last stage. The adequate combination of some of these techniques may result in a significant reduction of the residual monomer content in the final latex.

Synthetic Polymers at Interfaces: Monodisperse Emulsions Multiple Emulsions and Liquid Marbles

Science.gov (United States)

Sun, Guanqing

The adsorption of polymeric materials at interfaces is an energetically favorable process which is investigated in much diversified fields, such as emulsions, bubbles, foams, liquid marbles. Pickering emulsion, which is emulsion stabilized by solid particles has been investigated for over one century and preparation of Pickering emulsion with narrow size distribution is crucial for both the theoretical study of the stabilization mechanism and practical application, such as templated fabrication of colloidosomes. The precise control over the size and functionality of polymer latices allows the preparation of monodisperse Pickering emulsions with desired sizes through SPG membrane emulsification at rather rapid rate compared to microfludic production. Double or multiple emulsions have long been investigated but its rapid destabilization has always been a major obstacle in applying them into practical applications. The modern living polymerization techniques allow us to prepare polymers with designed structure of block copolymers which makes it possible to prepare ultra-stable multiple emulsions. The precise tuning of the ratio of hydrophobic part over the hydrophilic can unveil the stabilization mechanism. Liquid marble is a new type of materials of which liquid droplets are coated by dry particles. The coating of an outer layer of dry particles renders the liquid droplets non-sticky at solid surface which is useful in transportation of small amount of liquid without leakage at extreme low friction force. The property of liquid marbles relies largely on the stabilizers and the drying condition of polymeric latices is shown to have great influence on the property of liquid marbles. Firstly, an introduction to the interfacial and colloidal science with special attention to topics on emulsions, multiple emulsion and liquid marbles is given in Chapter 1. The unique features of an interface and a discussion on the definition of colloids are introduced prior to the

Formation of hyperbranched polymers in atom transfer radical copolymerization of MMA and DVB

Institute of Scientific and Technical Information of China (English)

无

2010-01-01

Hyperbranched poly(methyl methacrylate)s (HPMMAs) have been successfully prepared by atom transfer radical copolymerization of MMA and divinylbenzene (DVB).Kinetic study shows complete consumption of the initiator in 0.5 h,and relatively low polymerization rate when DVB content in the feed was high.By analyzing MALDI-TOF spectra of the resulting copolymers,the linear A n B (n=0,1,2,3) oligomers were formed in 0.5 h of polymerization,and then the oligomers reacted each other to form dimers,further reactions produced HPMMA.The SEC and NMR spectroscopies were used to trace the polymerization,and the results demonstrate that small amount of the branching reactions occur in the initial polymerization,and the branched polymers are significantly generated past a certain conversion depending upon the feed ratios.Raising the content of DVB in the monomer mixture can increase the pendent vinyl groups of the linear oligo-inimers,leading to gelation at low MMA conversion.

Analysis of Multiallelic CNVs by Emulsion Haplotype Fusion PCR.

Science.gov (United States)

Tyson, Jess; Armour, John A L

2017-01-01

Emulsion-fusion PCR recovers long-range sequence information by combining products in cis from individual genomic DNA molecules. Emulsion droplets act as very numerous small reaction chambers in which different PCR products from a single genomic DNA molecule are condensed into short joint products, to unite sequences in cis from widely separated genomic sites. These products can therefore provide information about the arrangement of sequences and variants at a larger scale than established long-read sequencing methods. The method has been useful in defining the phase of variants in haplotypes, the typing of inversions, and determining the configuration of sequence variants in multiallelic CNVs. In this description we outline the rationale for the application of emulsion-fusion PCR methods to the analysis of multiallelic CNVs, and give practical details for our own implementation of the method in that context.

Optimization of process parameter for graft copolymerization of glycidyl methacrylate onto delignified banana fibers

International Nuclear Information System (INIS)

Selambakkannu, S.; Nor Azillah Fatimah Othman; Siti Fatahiyah Mohamad

2016-01-01

This paper focused on pre-treated banana fibers as a trunk polymer for optimization of radiation-induced graft copolymerization process parameters. Pre-treated banana fiber was grafted with glycidyl methacrylate (GMA) via electron beam irradiation. Optimization of grafting parameters in term of grafting yield was analyzed at numerous radiation dose, monomer concentration and reaction time. Grafting yield had been calculated gravimetrically against all the process parameters. The grafting yield at 40 kGy had increases from 14 % to 22.5 % at 1 h and 24 h of reaction time respectively. Grafting yield at 1 % of GMA was about 58 % and it increases to 187 % at 3 % GMA. The grafting of GMA onto pre-treated banana fibers confirmed with the characterization using FTIR, SEM and TGA. Grafting of GMA onto pre-treated fibers was successfully carried out and it was confirmed by the results obtained via the characterization. (author)

Use of olive oil-in-water gelled emulsions in model turkey breast emulsions

Science.gov (United States)

Serdaroğlu, M.; Öztürk, B.

2017-09-01

Today, gelled emulsion systems offer a novel possibility in lipid modification of meat products. In this study, we aimed to investigate the quality characteristics of model turkey emulsions that were prepared with olive oil-in-water gelled emulsion (GE) as partial or total beef fat replacer. The results indicated that while most of the GE treatments showed equivalent emulsion characteristics in terms of emulsion stability, water-holding capacity and cook yield, utilization of 100% GE as the lipid source could increase total expressible fluid of the model turkey emulsion and thus negatively affect the quality. Utilization of GE was effective in total fat reduction, as the model turkey emulsions formulated with more than 50% GE had significantly lower fat content compared to full-beef fat control model emulsion. However, beef fat replacement with GE produced considerable changes in colour parameters. Finally, it was concluded that utilization of GE as a partial beef fat replacer has good potential to enhance stability and reduce total fat in turkey meat emulsion products.

Rheology of attractive emulsions.

Science.gov (United States)

Datta, Sujit S; Gerrard, Dustin D; Rhodes, Travers S; Mason, Thomas G; Weitz, David A

2011-10-01

We show how attractive interactions dramatically influence emulsion rheology. Unlike the repulsive case, attractive emulsions below random close packing, φ(RCP), can form soft gel-like elastic solids. However, above φ(RCP), attractive and repulsive emulsions have similar elasticities. Such compressed attractive emulsions undergo an additional shear-driven relaxation process during yielding. Our results suggest that attractive emulsions begin to yield at weak points through the breakage of bonds, and, above φ(RCP), also undergo droplet configurational rearrangements.

PENGARUH WAKTU REAKSI ETANOLISIS PADA SUHU RUANG TERHADAP RENDEMEN DAN STABILITAS EMULSI PRODUK ETANOLISIS Palm Kernel Oil (PKO [The Effect of Ethanolisis Reaction Time at Room Temperature on Yield and Emulsion Stability Ofproduct of Ethanolisis Palm Kernel Oil (PKO

Directory of Open Access Journals (Sweden)

Jessica Yunggo

2016-09-01

Full Text Available PKO (palm kernel oil is made from palm kernel of Elaesis gueneensis Jacq, which is a mixture of triglycerides. Triglycerides can be converted into a number of derivative products such as mono-diglycerides (MG-DG. MG-DG can be formed by ethanolisis reaction. In this study ethanolisis reaction of PKO was done by adding 96% of technical ethanol containing NaOH 1% (w/w PKO on PKO solution at a room temperature and a shorter time than the another PKO ethanolisis before. This study was aimed to find the best PKO ethanolisis reaction time in providing products of ethanolisis PKO with yield and high emulsion stability. The experiment was a nonfactorial  and arranged in a complete randomized block design (CRBD with four replications.  The single factor studied was 7 levels of  the reaction time in which  were 1, 3, 5, 7, 9, 11 and 13 minutes.  The data  were analysed using ANOVA and  further by Orthogonal polynomial on the significant level of 1% and 5%. The results showed that the reaction time ethanolisis had no effect on the yield and stability of the emulsion of fresh coconut milk. The yield of the resulting range between 17.32% - 18.07% and the stability of emulsion ranged between 88.88% - 92.50% during one day and 85.23% - 89.50% during two days. The sensory observation indicated that PKO ethanolisis product can preserve coconut milk for 3 days of storage time with color and scent of fresh coconut milk, and  more stable compared to control. Keywords: emulsion stability, ethanolisis, PKO, time, yield

Radiation-induced graft copolymerization of methyl acrylate and acrylic acid onto rubber wood fiber

International Nuclear Information System (INIS)

Saliza Jam; Mansor Ahmad; Wan Md Zin Wan Yunus; Khairul Zaman Mohd Dahlan

2001-01-01

Graft copolymerization of methyl acrylate and acrylic acid monomers onto rubber wood fiber (RWF) was carried out by simultaneous radiation-induced technique. The parameters affecting the grafting reaction were investigated and the optimum conditions for both monomers obtained are as follows: impregnation time = 16 hours, total dose = 30 kGy, methanol : water ratio, 3:1, monomers concentration = 40 v/v % and sulphuric acid concentration = 0.1 mol/L. Fourier Transform Infrared (FTIR), thermogravimetry analysis (TGA), and scanning electron microscope (SEM) analyses used to characterize graft copolymers. The structural investigation by x-ray diffraction (XRD) shows the degree of crystallinity of rubber wood fiber decreased with the incorporation of poly(methyl acrylate) and poly(acrylic acid) grafts. (Author)

Cut-off effect of radical TEMPO derivatives in olive oil-in-water emulsions.

Science.gov (United States)

Lopez de Arbina, Amaia; Rezende, Marcos Caroli; Aliaga, Carolina

2017-06-01

Three oil-in-water emulsions were prepared from mixtures of olive oil and Tween 20 in water. The effectiveness of a series of radical 2,2,6,6-tetramethylpiperidinoxyl (TEMPO) derivatives of variable lipophilicity in reactions with antioxidant Trolox, and as pyrene-fluorescence quenchers, was compared in the three emulsions. A "cut-off" effect was observed for the pyrene quenching by the probes, but not for their reaction with Trolox. The results were rationalized in terms of the amphiphobic nature of the probes, and the different locations of probe, pyrene and Trolox in the three-phase microheterogeneous systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Alternating copolymerization of fluoroalkenes with carbon monoxide.

Science.gov (United States)

Fujita, Tomoyuki; Nakano, Koji; Yamashita, Makoto; Nozaki, Kyoko

2006-02-15

The palladium-catalyzed alternating copolymerization of fluoroalkenes, represented as CH(2)=CH-CH(2)-C(n)F(2n+1), with CO was performed using (R,S)-BINAPHOS (2e) as a ligand. The CH(2)-C(n)F(2n+1) group is the most electronegative substituent ever reported for the copolymerization (Taft's sigma value of 0.90 for CH(2)CF(3)). The copolymer obtained from CH(2)=CH-CH(2)-C(8)F(17) (1a) existed as a mixture of polyspiroketal and polyketone, while that from CH(2)=CH-CH(2)-C(4)F(9) (1b) was a pure polyspiroketal, as was revealed by infrared and (13)C-CP/MAS NMR spectroscopies. The terminal structure of the polymer from 1b was confirmed by MALDI-TOF MS spectrometry. Detailed NMR studies suggested that the much higher reactivity with (R,S)-BINAPHOS (2e) than that with the conventional ligand DPPP (2a) can be attributed to the unique 1,2-insertion of the fluoroalkene into acylpalladium species. The existence of an electronegative substituent on the alpha-carbon of the palladium center is successfully avoided in the 1,2-insertion mechanism.

Study of the angular distribution of the secondary particles of anti pAg/Br reactions at 1. 4 GeV/c incident momentum observed in photographic emulsion

Energy Technology Data Exchange (ETDEWEB)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O. (Oslo Univ. (Norway). Fysisk Inst.)

1983-09-01

Some features of anti pAg/Br reactions at 1.4 GeV/c incident momentum are studied by means of the emulsion technique. The distribution of the number of charged particles/event are presented. The angular distributions indicate some anisotropic process in the nuclear matter, possibly shock-waves, and some back-to-back emission.

In situ NMR and modeling studies of nitroxide mediated copolymerization of styrene and n-butyl acrylate

NARCIS (Netherlands)

Hlalele, L.; Klumperman, L.

2011-01-01

The combination of in situ1H NMR and in situ31P NMR was used to study the nitroxide mediated copolymerization of styrene and n-butyl acrylate. The alkoxyamine MAMA-DEPN was employed to initiate and mediate the copolymerization. The nature of the ultimate/terminal monomer units of dormant polymer

Enzymatically interesterified fats based on mutton tallow and walnut oil suitable for cosmetic emulsions.

Science.gov (United States)

Kowalska, M; Mendrycka, M; Zbikowska, A; Stawarz, S

2015-02-01

Formation of emulsion systems based on interesterified fats was the objective of the study. Enzymatic interesterification was carried out between enzymatic mutton tallow and walnut oil in the proportions 2 : 3 (w/w) to produce fats not available in nature. At the beginning of the interesterification process, the balance between the interesterification and fat hydrolysis was intentionally disturbed by adding more water to the catalyst (Lipozyme IR MR) of the reaction to produce more of the polar fraction monoacylglycerols [MAGs] and diacylglycerols [DAGs]. To obtain a greater quantity of MAGs and DAGs in the reaction environment via hydrolysis, water was added (11, 13, 14, 16 w-%) to the enzymatic preparation. The obtained fats were used to form emulsions. The emulsions were evaluated with respect to sensory and skin moisturizing properties by 83 respondents. Determination of emulsion stability using temperature and centrifugal tests was carried out. Morphology and the type of emulsions were determined. The respondents described the skin to which the emulsions in testing were applied as smooth, pleasant to touch and adequately moisturized. The work has demonstrated that interesterification of a mutton tallow and walnut oil blend resulted in new fats with very interesting characteristics of triacylglycerols that are not present in the environment. The results of the present work indicate the possibility of application of fats with the largest quantity of MAGs and DAGs as a fat base of emulsions in the cosmetic industries. The hypothesis assumed in this work of producing additional quantities of MAGs and DAGs (in the process of enzymatic interesterification) responsible for the stability of the system was confirmed. It should be pointed out that the emulsions based on interesterified fats exhibited a greater level of moisturization of the skin than the emulsions containing non-interesterified fat. Also, in the respondents' opinion, the emulsion containing fat, which

Alternating copolymerization of epoxides with anhydrides initiated by organic bases

Czech Academy of Sciences Publication Activity Database

Hošťálek, Z.; Trhlíková, Olga; Walterová, Zuzana; Martinez, T.; Peruch, F.; Cramail, H.; Merna, J.

2017-01-01

Roč. 88, March (2017), s. 433-447 ISSN 0014-3057 Institutional support: RVO:61389013 Keywords : copolymerization * epoxides * anhydrides Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer science Impact factor: 3.531, year: 2016

Creating nanoscale emulsions using condensation.

Science.gov (United States)

Guha, Ingrid F; Anand, Sushant; Varanasi, Kripa K

2017-11-08

Nanoscale emulsions are essential components in numerous products, ranging from processed foods to novel drug delivery systems. Existing emulsification methods rely either on the breakup of larger droplets or solvent exchange/inversion. Here we report a simple, scalable method of creating nanoscale water-in-oil emulsions by condensing water vapor onto a subcooled oil-surfactant solution. Our technique enables a bottom-up approach to forming small-scale emulsions. Nanoscale water droplets nucleate at the oil/air interface and spontaneously disperse within the oil, due to the spreading dynamics of oil on water. Oil-soluble surfactants stabilize the resulting emulsions. We find that the oil-surfactant concentration controls the spreading behavior of oil on water, as well as the peak size, polydispersity, and stability of the resulting emulsions. Using condensation, we form emulsions with peak radii around 100 nm and polydispersities around 10%. This emulsion formation technique may open different routes to creating emulsions, colloidal systems, and emulsion-based materials.

A study of the angular distribution of the secondary particles of anti pAg/Br reactions at 1.4 GeV/c incident momentum observed in photographic emulsion

International Nuclear Information System (INIS)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1983-04-01

Some features of anti pAg/Br reactions at 1.4 GeV/c incident momentum are studied by means of the emulsion technique. The distributions of the number of charged particles/event are presented. The angular distributions indicate som anisotropic process in the nuclear matter, possibly shock waves, and some back-to-back emission

Theoretical analysis of factors controlling the nonalternating CO/C(2)H(4) copolymerization.

Science.gov (United States)

Haras, Alicja; Michalak, Artur; Rieger, Bernhard; Ziegler, Tom

2005-06-22

A [P-O]Pd catalyst based on o-alkoxy derivatives of diphenylphosphinobenzene sulfonic acid (I) has recently been shown by Drent et al. to perform nonalternating CO/C(2)H(4) copolymerization with subsequent incorporation of ethylene units into the polyketone chain. The origin of the nonalternation is investigated in a theoretical study of I, where calculated activation barriers and reaction heats of all involved elementary steps are used to generate a complete kinetic model. The kinetic model is able to account for the observed productivity and degree of nonalternation as a function of temperature. Consistent with the energy changes obtained for the real catalyst model, the selectivity toward a nonalternating distribution of both comonomers appears to be mainly a result of a strong destabilization of the Pd-acyl complex.

The radiation-induced copolymerization of vinyl acetate with dibutyl maleate

International Nuclear Information System (INIS)

Du Plessis, T.A.; Lustig, A.

1975-01-01

The radiation-induced copolymerization of vinyl acetate with dibutyl maleate was investigated in the temperature range from -50 0 to 90 0 . A copolymer of the unsaturated ester with vinyl acetate was obtained in which the comonomers alternate with regularity along the polymer chain over the entire range of comonomer compositions and temperature range investigated. Both the rate of copolymerization and the molecular weight of the resulting copolymer were found to depend strongly on the comonomer composition. The monomer reactivity ratios were found to be practically zero. The apparent activation energy was found to change at 5 0 with an increase in temperature from a value of 1,6 kcal/mole to a value of 4,4kcal/mole. Scavenger studies indicate that a free radical mechanism prevails over the entire temperature range investigated. (Author) [af

A study of the angular distribution of the secondary particles of anti pAg/Br reactions at 1.4 GeV/c incident momentum observed in photographic emulsion

International Nuclear Information System (INIS)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1983-01-01

Some features of anti pAg/Br reactions at 1.4 GeV/c incident momentum are studied by means of the emulsion technique. The distribution of the number of charged particles/event are present. The angular distributions indicate some anisotropic process in the nuclear matter, possibly shock-waves, and some back-to-back emission. (Auth.)

How emulsions composition and structure affect sensory perception of low-viscosity model emulsions

NARCIS (Netherlands)

Vingerhoeds, M.H.; Wijk, de R.A.; Zoet, F.D.; Nixdorf, R.R.; Aken, van G.A.

2008-01-01

The oral residence time of low-viscosity emulsions, like milk, is relatively short. Despite this short residence time, people can easily perceive differences between these emulsions. Our research is dedicated to unravel the oral behaviour of emulsions in relation to sensory perception. The aim of

Ruthenium phosphine complexes as catalysts for alternating co-polymerization of ethylene and CO

International Nuclear Information System (INIS)

Gusev, O.V.; Kal'sin, A.M.; Peganov, T.A.; Petrovskij, P.V.; Belov, G.P.; Novikova, E.V.

2000-01-01

Ruthenium (2) complexes, [Ru(dppe) 2 (OTs) 2 ] and [Ru(PhP(CH 2 CH 2 CH 2 PPh 2 ) 2 )(OTs) 2 ], where dppe (diphenylphosphino)ethane; OTs = tosylate, were synthesized with the yield of 67 and 76%, respectively, and characterized by 31 P NMR. The properties of the above complexes as catalysts of alternating co-polymerization of ethylene and carbon monoxide were studied. A considerable increase in catalytic activity of the complexes was established in the presence of trifluoroacetic acid and 1,4-benzoquinone. These compounds are the first example of ruthenium complexes that catalyse co-polymerization of ethylene and CO [ru

Rheology of unstable mineral emulsions

Directory of Open Access Journals (Sweden)

Sokolović Dunja S.

2013-01-01

Full Text Available In this paper, the rheology of mineral oils and their unstable water emulsion were investigated. The oil samples were domestic crude oil UA, its fractions UA1, UA4 and blend semi-product UP1, while the concentration of oil in water emulsions was in the range from 1 up to 30%. The results were analyzed based on shear stress. The oil samples UA, UA1 and UP1 are Newtonian fluids, while UA4 is pseudoplastic fluid. The samples UA and UA4 show higher value of shear stress (83.75 Pa, 297 Pa, then other two samples UA1 and UP1 (18.41 Pa, 17.52 Pa. Rheology of investigated oils due to its complex chemical composition should be analyzed as a simultaneous effect of all their components. Therefore, structural composition of the oils was determined, namely content of paraffins, naphthenes, aromatics and asphaltenes. All samples contain paraffins, naphthenes and aromatics but only oils UA and UA4 contain asphaltenes as well. All investigated emulsions except 30% EUA4 are Newtonian fluids. The EUA4 30% emulsion shows pseudoplastic behaviour, and it is the only 30% emulsion among investigated ones that achieves lower shear stress then its oil. The characteristics of oil samples that could have an influence on their properties and their emulsion rheology, were determined. These characteristics are: neutralization number, interfacial tension, dielectric constant, and emulsivity. Oil samples UA and UA4 have significantly higher values of neutralization number, dielectric constants, and emulsivity. The sample UA has the lowest value of interface tension and the greatest emulsivity, indicating that this oil, among all investigated, has the highest preference for building emulsion. This could be the reason why 20% and 30% emulsions of the oil UA achieve the highest shear stress among all investigated emulsions.

Radiation-chemical copolymerization of oligoalkylene- maleinants of alicyclic structure

International Nuclear Information System (INIS)

Bondarenko, P.A.; Videnina, N.G.; Omel'chenko, S.I.

1982-01-01

Effect of glycol used in synthesis on the properties of oligoalkylenemaleinates and their copolymers is considered. It is shown that oligoesters during copolymerization with sterol have enough high sensitivity to the effect of gamma radiation and electrons of high energy. The copolymers have a good mechanical-and-physical properties at low absorbed doses

Cheese powder as an ingredient in emulsion sausages

DEFF Research Database (Denmark)

Chen, Xiang; Ruiz Carrascal, Jorge; Petersen, Mikael Agerlin

2017-01-01

Different types of cheese powder were added to meat emulsion sausages in order to address its influence on chemical composition, volatile compounds profile and sensory properties, and its potential to reduce salt content through boosting saltiness. Addition of cheese powder to emulsion sausages...... modified their profile of volatile compounds. Blue cheese increased some ketones, alcohols, and esters, while brown cheese brought typical Maillard reaction compounds. Overall, addition of cheese powders to sausages enhanced the intensity of flavour traits. A mixture of hard and blue cheese powder showed...... the highest effect on boosting saltiness, while brown cheese powder showed the strongest umami and meat flavour boosting effect, and sausages with added blue cheese powder showed a more intense aftertaste. Hardness significantly increased due to the addition of blue cheese powder. Addition of cheese powder...

STYRENE/STYRENE-DERIVATIVE COPOLYMERIZATION BY PH2Zn-METALLOCENE-MAO SYSTEMS: HOMO- AND COPOLYMERIZATION OF á-METHYLSTYRENE WITH STYRENE

OpenAIRE

RABAGLIATI, FRANCO M; MUÑOZ, HÉCTOR E; MARDONES, GABRIELA V

2010-01-01

The copolymerization of styrene with á-methylstyrene has been tested using combined metallocene-MAO initiator systems with and without diphenylzinc. The metallocenes used were biscyclopentadienyltitanium dichloride, Cp2TiCl2, bis(n-butylcyclopentadienyl)titanium dichloride, (n-BuCp)2TiCl2, and the half-sandwich metallocene indenyltitanium trichloride, IndTiCl3. The results indicate that both binary metallocene-MAO, and ternary Ph2Zn-metallocene-MAO systems are capable of polymerizing á-methyl...

Polytetrafluorethylene (PTFE) copolymerization with N-N'- dimethyl acrylamide (DMAA) using gamma radiation

International Nuclear Information System (INIS)

Queiroz, A.A. de; Higa, O.Z.

1990-01-01

The copolymerization of N-N'-dimethylacrylamide monomer with polytetrafluorethylene was made using an insert technique by gamma irradiation. The polimeric surface was characterized by electron microscopy. (author) [pt

Parallel 3-D image processing for nuclear emulsion

International Nuclear Information System (INIS)

Nakano, Toshiyuki

2001-01-01

The history of nuclear plate was explained. The first nuclear plate was named as pellicles covered with 600 μm of emulsion in Europe. In Japan Emulsion Cloud Chamber (ECC) using thin emulsion (50 μm) type nuclear plate was developed in 1960. Then, the semi-automatic analyzer (1971) and automatic analyzer (1980), Track Selector (TS) with memory stored 16 layer images in 512 x 512 x 16 pixel were developed. Moreover, NTS (New Track Selector), speeding up analyzer, was produced for analysis of results of CHORUS experiment in 1996. Simultaneous readout of 16 layer images had been carried out, but UTS (Ultra Track Selector) made possible to progressive treatment of 16 layers of some data and determination of traces in all angles. Direct detection of tau neutrino (VT) was studied by DONUT (FNAL E872) using UTS and nuclear plate. Neutrino beam was produced by 800 GeV proton beam hitting the fixed target. About 1100 phenomena of neutrino reactions were observed during six months of irradiation. 203 phenomena were detected. 4 examples were shown in this paper. OPERA experiment by SK is explained. (S.Y.)

Bulk-loaded emulsion explosives technology

Energy Technology Data Exchange (ETDEWEB)

Borg, D.G. [Blasting Analysis International, Inc., Allentown, PA (United States)

1995-01-01

The largest use of emulsion explosives and emulsion-Anfo blends is in surface mining operations. An emulsion explosive is a two-phase system: the inner phase is madeup of an oxidizer solution; the outer phase is made up of oils or an oil/wax blend. Emulsion Anfo blends have been used to expand drill patterns, increase fragmentation, and provide extra energy for blast casting. 3 tabs.

Emulsion Science Basic Principles

CERN Document Server

Leal-Calderon, Fernando; Schmitt, Véronique

2007-01-01

Emulsions are generally made out of two immiscible fluids like oil and water, one being dispersed in the second in the presence of surface-active compounds.They are used as intermediate or end products in a huge range of areas including the food, chemical, cosmetic, pharmaceutical, paint, and coating industries. Besides the broad domain of technological interest, emulsions are raising a variety of fundamental questions at the frontier between physics and chemistry. This book aims to give an overview of the most recent advances in emulsion science. The basic principles, covering aspects of emulsions from their preparation to their destruction, are presented in close relation to both the fundamental physics and the applications of these materials. The book is intended to help scientists and engineers in formulating new materials by giving them the basics of emulsion science.

On-line measurement with automatic emulsion analysis system and off-line data processing (E531 neutrino experiment)

International Nuclear Information System (INIS)

Miyanishi, Motoaki

1984-01-01

The automatic emulsion analysis system developed by Nagoya cosmic ray observation group was practically used for the experiment (FNAL-E531) on determining the lifetime of charm particles for the first time in the world, and achieved a great successful result. The system consists of four large precise coordinate-measuring stages capable of conducting simultaneous measurement and multiple (currently four) DOMS (digitized on-line microscope), supported with one mini-computer (ECLIPS S/130). The purpose of E531 experiment was the determination of charm particle lifetime. The experiment was carried out at FNAL, USA, and by the irradiation of wide band ν sub(μ) beam equivalent to 7 x 10 18 of 350 GeV/c protons. The detector was a hybrid system of emulsions and a counter spectrometer. The scan of neutrino reaction, the scan of charm particles, and charm event measurement were analyzed in emulsions, and the on-line programs for-respective analyses were created. Nagoya group has found 726 neutrino reactions in the first run, obtained 37 charm particle candidates, and found 1442 neutrino reactions in the second run, and obtained 56 charm particle candidates. The capability of the automatic emulsion analysis system in terms of the time equired for analysis is in total 3.5 hours per event; 15 minutes for C.S. scan, 15 minutes for coupling to module, 20 minutes for tracing to vertex, 1 hour for neutrino reaction measurement, 10 minutes for offline data processing and 1.5 hours for charm particle scanning. (Wakatsuki, Y.)

Spectroscopic study of monitoring the kinetics of radical copolymerization of di(ethylene glycol) bis(allylcarbonate) and 2-naphthylmethacrylate

Science.gov (United States)

Barashkov, N. N.; Novikova, T. S.; Sakhno, T. V.; Bulgakova, L. M.

1996-03-01

The results of fluorescence monitoring in the radical copolymerization of di(ethylene glycol) bis(allylcarbonate) and 2-naphthylmethacrylate are discussed. Our studies suggest that data based on measurement of the intensity of the fluorescence band at 345 nm during copolymerization are in good agreement with the data obtained by the traditional dilatometric method.

Some features of the angular distribution of the grey tracks observed in anti pAg/Br reactions at 1.4 GeV/c in photographic emulsions

International Nuclear Information System (INIS)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1984-01-01

We study the angular distributions of the non-relativistic fast charged particles in anti pAg/Br reactions at 1.4 GeV/c incident momentum in photographic emulsions. For some events with three such particles, two of them are emitted in almost opposite directions, or ''back-to-back''. Some of these particles have been identified as protons. Possibly has a multinucleon cluster or ''hot-spot'' in the target nucleus decayed. (orig.)

Salphen-Co(III) complexes catalyzed copolymerization of epoxides with CO2

Czech Academy of Sciences Publication Activity Database

Hošťálek, Z.; Mundil, R.; Císařová, I.; Trhlíková, Olga; Grau, E.; Peruch, F.; Cramail, H.; Merna, J.

2015-01-01

Roč. 63, 20 April (2015), s. 52-61 ISSN 0032-3861 Institutional support: RVO:61389013 Keywords : cobalt salphen catalyst * CO2 epoxide copolymerization * MALDI-TOF Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.586, year: 2015

LPV model development and control of a solution copolymerization reactor

NARCIS (Netherlands)

Rahme, S.; Abbas, H.M.S.; Meskin, N.; Tóth, R.; Mohammadpour, J.

2016-01-01

In this paper, linear parameter-varying (LPV) control is considered for a solution copolymerization reactor, which takes into account the time-varying nature of the parameters of the process. The nonlinear model of the process is first converted to an exact LPV model representation in the

Emulsion characteristics, chemical and textural properties of meat systems produced with double emulsions as beef fat replacers.

Science.gov (United States)

Serdaroğlu, Meltem; Öztürk, Burcu; Urgu, Müge

2016-07-01

In recent years, double emulsions are stated to have a promising potential in low-fat food production, however, there are very few studies on their possible applications in meat matrices. We aimed to investigate the quality of beef emulsion systems in which beef fat was totally replaced by double emulsions (W1/O/W2) prepared with olive oil and sodium caseinate (SC) by two-step emulsification procedure. Incorporation of W1/O/W2 emulsion resulted in reduced lipid, increased protein content, and modified fatty acid composition. W1/O/W2 emulsion treatments had lower jelly and fat separation, higher water-holding capacity and higher emulsion stability than control samples with beef fat. Increased concentrations of W1/O/W2 emulsions resulted in significant changes in texture parameters. TBA values were lower in W1/O/W2 emulsion treatments than control treatment after 60days of storage. In conclusion, our study confirms that double emulsions had promising impacts on modifying fatty acid composition and developing both technologically and oxidatively stable beef emulsion systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

Asphalt emulsion; Asphalt nyuzai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Suzuki, T. [Toa Doro Kogyo Co. Ltd., Tokyo (Japan)

1994-12-28

The emulsification, manufacture, type, applications, etc. of asphalt emulsion were introduced. The emulsification of asphalt is obtained by mixing heated asphalt into an emulsification liquid where emulsifier is added to water and then agitating it. The emulsifier has both hydrophilic and lipophilic parts in the same molecule, prevents collision between asphalt particles after being arranged properly on the surface of asphalt particles, and prevent separation into water and asphalt. The emulsion is available for penetration and for mixing depending on applications and can be classified into cation emulsion, anion emulsion, and nonionic emulsion according to the property. The emulsion is mainly applied to road pavement, reaching approximately 90 % of the total manufactured emulsion. It is also used for other areas such as the filler of a slab race of each bullet train of Sanyo, Tohoku, and Jyoetsu and is also applied to the formation of a water-proof layer by spraying a high-concentration emulsion with rubber, agricultural water channels using asphalt emulsion and nonwoven cloth, etc. in civil engineering and agricultural fields. 2 refs., 13 figs., 8 tabs.

Development of automatic nuclear emulsion plate analysis system and its application to elementary particle reactions, 2

International Nuclear Information System (INIS)

Ushida, Noriyuki; Otani, Masashi; Kumazaki, Noriyasu

1984-01-01

This system is composed of precise coordinate measuring apparatuses, a stage controller and various peripherals, employing NOVA 4/C as the host computer. The analyzed results are given as the output to a printer or an XY plotter. The data required for experiment, sent from Nagoya University and others, are received by the host computer through an acoustic coupler, and stored in floppy disks. This paper contains simple explanation on the monitor for the events which occur immediately after the on-line measurement ''MTF 1'', the XY plotter and the acoustic coupler, which hold important position in the system in spite of low cost, due to the development of useful program, as those were not described in the previous paper. The three-dimensional reconstruction of tracks and various errors, corrective processing and analytical processing after corrective processing as off-line processing are also described. In addition, the application of the system was made to the E-531 neutrino experiment in Fermi National Accelerator Laboratory, which attempted to measure the life of the charm particles generated in neutrino reaction with a composite equipment composed of nuclear plates and various counters. First, the outline of the equipment, next, the location of neutrino reaction and the surveillance of charm particle decay using MTF program as the analyzing method at the target, and thirdly, the emulsion-counter data fitting are explained, respectively. (Wakatsuki, Y.)

Comparison of Polymer Networks Synthesized by Conventional Free Radical and RAFT Copolymerization Processes in Supercritical Carbon Dioxide

OpenAIRE

Patricia Pérez-Salinas; Gabriel Jaramillo-Soto; Alberto Rosas-Aburto; Humberto Vázquez-Torres; María Josefa Bernad-Bernad; Ángel Licea-Claverie; Eduardo Vivaldo-Lima

2017-01-01

There is a debate in the literature on whether or not polymer networks synthesized by reversible deactivation radical polymerization (RDRP) processes, such as reversible addition-fragmentation radical transfer (RAFT) copolymerization of vinyl/divinyl monomers, are less heterogeneous than those synthesized by conventional free radical copolymerization (FRP). In this contribution, the syntheses by FRP and RAFT of hydrogels based on 2-hydroxyethylene methacrylate (HEMA) and ethylene glycol dimet...

In-situ radiation dosimetry based on Radio-Fluorogenic Co-Polymerization

NARCIS (Netherlands)

Warman, J.M.; Luthjens, L.H.; De Haas, M.P.

2009-01-01

A fluorimetric method of radiation dosimetry is presented for which the intensity of the fluorescence of a (tissue equivalent) medium is linearly dependent on accumulated dose from a few Gray up to kiloGrays. The method is based on radio-fluorogenic co-polymerization (RFCP) in which a normally very

Investigation of the production of slow particles in 60 A GeV 16O induced nuclear emulsion reaction

International Nuclear Information System (INIS)

Zhang Donghai

2001-01-01

The multiplicity distributions and correlations of grey track producing particles (N g ), black track producing particles (N b ) and heavy track producing particles (N h ) have been studied in 60 A GeV 16 O induced nuclear emulsion reaction. The multiplicity distributions of grey particles, black particles and heavy track producing particles can be reproduced by FRITIOF (version 1.7) taking cascade mechanism in to account and DTUNUC2.0 with an incident energy of 200 A GeV. The mean multiplicity of black particles (N b ) increases with the number of grey particle N g up to 10 and then exhibits a saturation for peripheral, central and mini-bias events; the average values of grey particles g > (heavy track producing particles h > increase with increasing values of black particle N b (grey particle N g )

Some features of the angular distribution of the grey tracks observed in anti pAg/Br reactions at 1. 4 GeV/c in photographic emulsions

Energy Technology Data Exchange (ETDEWEB)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O. (Oslo Univ. (Norway). Fysisk Inst.)

1984-12-01

We study the angular distributions of the non-relativistic fast charged particles in anti pAg/Br reactions at 1.4 GeV/c incident momentum in photographic emulsions. For some events with three such particles, two of them are emitted in almost opposite directions, or ''back-to-back''. Some of these particles have been identified as protons. Possibly has a multinucleon cluster or ''hot-spot'' in the target nucleus decayed.

Novel star-type methoxy-poly(ethylene glycol) (PEG)-poly({epsilon}-caprolactone) (PCL) copolymeric nanoparticles for controlled release of curcumin

Energy Technology Data Exchange (ETDEWEB)

Feng Runliang; Zhu Wenxia; Song Zhimei, E-mail: zhimei_song@126.com [University of Jinan, Shandong Academy of Medical Science, Department of Pharmaceutical Engineering, School of Medicine and Life Sciences (China); Zhao Liyan [Hebei North University, Department of Pharmacy (China); Zhai Guangxi [Shandong University, Department of Pharmaceutics, College of Pharmacy (China)

2013-06-15

To improve curcumin's (CURs) water solubility and release property, a novel star methoxy poly(ethylene glycol)-poly({epsilon}-caprolactone) (MPEG-PCL) copolymer was synthesized through O-alkylation, basic hydrolysis and ring-opening polymerization reaction with MPEG, epichlorohydrin, and {epsilon}-caprolactone as raw materials. The structure of the novel copolymer was characterized by {sup 1}H NMR, FT-IR, and GPC. The results of FT-IR and differential scanning calorimeter of CUR-loaded nanoparticles (NPs) prepared by dialysis method showed that CUR was successfully encapsulated into the SMP12 copolymeric NPs with 98.2 % of entrapment efficiency, 10.91 % of drug loading, and 88.4 {+-} 11.2 nm of mean particle diameter in amorphous forms. The dissolubility of nanoparticulate CUR was increased by 1.38 Multiplication-Sign 10{sup 5} times over CUR in water. The obtained blank copolymer showed no hemolysis. A sustained CUR release to a total of approximately 56.13 % was discovered from CUR-NPs in 40 % of ethanol saline solution within 72 h on the use of dialysis method. The release behavior fitted the ambiexponent and biphasic kinetics equation. In conclusion, the copolymeric NPs loading CUR might serve as a potential nanocarrier to improve the solubility and release property of CUR.

Novel star-type methoxy-poly(ethylene glycol) (PEG)-poly(ɛ-caprolactone) (PCL) copolymeric nanoparticles for controlled release of curcumin

Science.gov (United States)

Feng, Runliang; Zhu, Wenxia; Song, Zhimei; Zhao, Liyan; Zhai, Guangxi

2013-06-01

To improve curcumin's (CURs) water solubility and release property, a novel star methoxy poly(ethylene glycol)-poly(ɛ-caprolactone) (MPEG-PCL) copolymer was synthesized through O-alkylation, basic hydrolysis and ring-opening polymerization reaction with MPEG, epichlorohydrin, and ɛ-caprolactone as raw materials. The structure of the novel copolymer was characterized by 1H NMR, FT-IR, and GPC. The results of FT-IR and differential scanning calorimeter of CUR-loaded nanoparticles (NPs) prepared by dialysis method showed that CUR was successfully encapsulated into the SMP12 copolymeric NPs with 98.2 % of entrapment efficiency, 10.91 % of drug loading, and 88.4 ± 11.2 nm of mean particle diameter in amorphous forms. The dissolubility of nanoparticulate CUR was increased by 1.38 × 105 times over CUR in water. The obtained blank copolymer showed no hemolysis. A sustained CUR release to a total of approximately 56.13 % was discovered from CUR-NPs in 40 % of ethanol saline solution within 72 h on the use of dialysis method. The release behavior fitted the ambiexponent and biphasic kinetics equation. In conclusion, the copolymeric NPs loading CUR might serve as a potential nanocarrier to improve the solubility and release property of CUR.

Catalytic copolymerization of CO and ethylene with a charge neutral palladium(II) zwitterion.

Science.gov (United States)

Lu, Connie C; Peters, Jonas C

2002-05-15

The synthesis of a zwitterionic Pd(II) complex supported by an anionic bis(phosphino)borate ligand, Ph(2)B(CH(2)PPh(2))(2) (abbreviated as [Ph(2)BP(2)]), is reported. The new complex, [Ph(2)BP(2)]PdMe(THF), is active for CO and ethylene copolymerization. The copolymerization activity and polyketone molecular weight for the neutral, zwitterionic system are compared with those for the cationic systems [R(2)E(CH(2)PPh(2))(2)PdMe(THF)][B(C(6)F(5))(4)] where ER(2) = SiPh(2) and CH(2). Surprisingly, the more electron rich zwitterionic system is a catalyst of activity comparable to that of the more conventional cationic systems.

Molecular weight control in emulsion polymerization by catalytic chain transfer : a reaction engineering approach

NARCIS (Netherlands)

Smeets, N.M.B.; Meda, U.S.; Heuts, J.P.A.; Keurentjes, J.T.F.; Herk, van A.M.; Meuldijk, J.

2007-01-01

For the application of catalytic chain transfer in (mini)emulsion polymerization, catalyst partitioning and deactivation are key parameters that govern the actual catalyst concentration at the locus of polymerization and consequently the final molecular weight distribution. A global model, based on

A Scalable Method toward Superhydrophilic and Underwater Superoleophobic PVDF Membranes for Effective Oil/Water Emulsion Separation.

Science.gov (United States)

Yuan, Tao; Meng, Jianqiang; Hao, Tingyu; Wang, Zihong; Zhang, Yufeng

2015-07-15

A superhydrophilic and underwater superoleophobic PVDF membrane (PVDFAH) has been prepared by surface-coating of a hydrogel onto the membrane surface, and its superior performance for oil/water emulsion separation has been demonstrated. The coated hydrogel was constructed by an interfacial polymerization based on the thiol-epoxy reaction of pentaerythritol tetrakis (3-mercaptopropionate) (PETMP) with diethylene glycol diglycidyl ether (PEGDGE) and simultaneously tethered on an alkaline-treated commercial PVDF membrane surface via the thio-ene reaction. The PVDFAH membranes can be fabricated in a few minutes under mild conditions and show superhydrophilic and underwater superoleophobic properties for a series of organic solvents. Energy dispersive X-ray (EDX) analysis shows that the hydrogel coating was efficient throughout the pore lumen. The membrane shows superior oil/water emulsion separation performance, including high water permeation, quantitative oil rejection, and robust antifouling performance in a series oil/water emulsions, including that prepared from crude oil. In addition, a 24 h Soxhlet-extraction experiment with ethanol/water solution (50:50, v/v) was conducted to test the tethered hydrogel stability. We see that the membrane maintained the water contact angle below 5°, indicating the covalent tethering stability. This technique shows great promise for scalable fabrication of membrane materials for handling practical oil emulsion purification.

Characterization of flaxseed oil emulsions.

Science.gov (United States)

Lee, Pei-En; Choo, Wee-Sim

2015-07-01

The emulsifying capacity of surfactants (polysorbate 20, polysorbate 80 and soy lecithin) and proteins (soy protein isolate and whey protein isolate) in flaxseed oil was measured based on 1 % (w/w) of emulsifier. Surfactants showed significantly higher emulsifying capacity compared to the proteins (soy protein isolate and whey protein isolate) in flaxseed oil. The emulsion stability of the flaxseed oil emulsions with whey protein isolate (10 % w/w) prepared using a mixer was ranked in the following order: 1,000 rpm (58 min) ≈ 1,000 rpm (29 min) ≈ 2,000 rpm (35 min) >2,000 rpm (17.5 min). The emulsion stability of the flaxseed oil emulsions with whey protein isolate (10 % w/w) prepared using a homogenizer (Ultra Turrax) was independent of the speed and mixing time. The mean particle size of the flaxseed oil emulsions prepared using the two mixing devices ranged from 23.99 ± 1.34 μm to 47.22 ± 1.99 μm where else the particle size distribution and microstructure of the flaxseed oil emulsions demonstrated using microscopic imaging were quite similar. The flaxseed oil emulsions had a similar apparent viscosity and exhibited shear thinning (pseudoplastic) behavior. The flaxseed oil emulsions had L* value above 70 and was in the red-yellow color region (positive a* and b* values).

Selective enhancement of boron accumulation with boron-entrapped water-in-oil-water emulsion in VX-2 rabbit hepatic cancer model for BNCT

International Nuclear Information System (INIS)

Yanagie, Hironobu; Higashi, Shushi; Ikushima, Ichiro

2006-01-01

Tumor cell destruction in boron neutron-capture therapy (BNCT) is due to the nuclear reaction between 10 B and thermal neutrons. It is necessary for effective BNCT therapy to accumulate 10 B atoms in the tumor cells without affecting adjacent healthy cells. Water-in-oil-water (WOW) emulsion was used as the carrier of anti-cancer agents on arterial injections in clinical cancer treatment. In this study, we prepared 10 BSH entrapped WOW emulsion for selective arterial infusion for the treatment of hepatocellular carcinoma. WOW emulsion was administrated by arterial injections via proper hepatic artery. The anti-tumor activity of the emulsion was compared with 10 BSH-Lipiodol mix emulsion or 10 BSH solutions on VX-2 rabbit hepatic tumor models. The 10 B concentrations in VX-2 tumor on delivery with WOW emulsion was superior to those by conventional lipiodol mix emulsion. Electro-microscopic figures of WOW emulsion delineated the accumulation of fat droplets of WOW emulsion in the tumor site, but there was no accumulation of fat droplets in lipiodol emulsion. These results indicate that 10 B entrapped WOW emulsion is most useful carrier for arterial delivery of boron agents on BNCT to cancer. (author)

Optimal Design for Reactivity Ratio Estimation: A Comparison of Techniques for AMPS/Acrylamide and AMPS/Acrylic Acid Copolymerizations

Directory of Open Access Journals (Sweden)

Alison J. Scott

2015-11-01

Full Text Available Water-soluble polymers of acrylamide (AAm and acrylic acid (AAc have significant potential in enhanced oil recovery, as well as in other specialty applications. To improve the shear strength of the polymer, a third comonomer, 2-acrylamido-2-methylpropane sulfonic acid (AMPS, can be added to the pre-polymerization mixture. Copolymerization kinetics of AAm/AAc are well studied, but little is known about the other comonomer pairs (AMPS/AAm and AMPS/AAc. Hence, reactivity ratios for AMPS/AAm and AMPS/AAc copolymerization must be established first. A key aspect in the estimation of reliable reactivity ratios is design of experiments, which minimizes the number of experiments and provides increased information content (resulting in more precise parameter estimates. However, design of experiments is hardly ever used during copolymerization parameter estimation schemes. In the current work, copolymerization experiments for both AMPS/AAm and AMPS/AAc are designed using two optimal techniques (Tidwell-Mortimer and the error-in-variables-model (EVM. From these optimally designed experiments, accurate reactivity ratio estimates are determined for AMPS/AAm (rAMPS = 0.18, rAAm = 0.85 and AMPS/AAc (rAMPS = 0.19, rAAc = 0.86.

Metal-Free Alternating Copolymerization of CO2with Epoxides: Fulfilling “Green” Synthesis and Activity

KAUST Repository

Zhang, Dongyue

2016-08-16

Polycarbonates were successfully synthesized for the first time through the anionic copolymerization of epoxides with CO2, under metal-free conditions. Using an approach based on the activation of epoxides by Lewis acids and of CO, by appropriate cations, well-defined alternating copolymers made of CO, and propylene oxide (PO) or cyclohexene oxide (CHO) were indeed obtained. Triethyl borane was the Lewis acid chosen to activate the epoxides, and onium halides or onium alkoxides involving either ammonium, phosphonium, or phosphazenium cations were selected to initiate the copolymerization. In the case of PO, the carbonate content of the poly(propylene carbonate) formed was in the range of 92-99% and turnover numbers (TON) were close to 500; in the case of CHO perfectly alternating poly(cyclohexene carbonate) were obtained and TON values were close to 4000. The advantages of such a copolymerization system are manifold: (i) no need for multistep catalyst/ligand synthesis as in previous works; (ii) no transition metal involved in the copolymer synthesis and therefore no coloration of the samples isolated; and (iii) no necessity for postsynthesis purification.

Surface modification of poly(tetrafluoroethylene) films by low energy Ar+ ion-beam activation and UV-induced graft copolymerization

International Nuclear Information System (INIS)

Zhang Yan; Huan, A.C.H.; Tan, K.L.; Kang, E.T.

2000-01-01

Surface modification of poly(tetrafluoroethylene) (PTFE) films by Ar + ion-beam irradiation with varying ion energy and ion dose was carried out. The changes in surface composition of the irradiated PTFE films were characterized, both in situ and after exposure to air, by X-ray photoelectron spectroscopy (XPS). The possible mechanisms of chemical reaction induced by the incident ion beam on the surface of PTFE film included defluorination, chain scission and cross-linking, as indicated by the presence of the characteristic peak components associated with the - - -CF 3 , - - -CF, and C(CF 2 ) 4 species in the C 1s core-level spectra, the decrease in surface [F]/[C] ratio, and the increase in surface micro-hardness of the Ar + ion-beam-treated PTFE films. Furthermore, the free radicals generated by the ion-beam could react with oxygen in the air to give rise to oxidized carbon species, such as the peroxides, on the PTFE surface. Thus, after exposure to air, the Ar + ion-beam-pretreated PTFE films were susceptible to further surface modification by UV-induced graft copolymerization with a vinyl monomer, such as acrylamide (AAm). The graft concentrations were deduced from the XPS-derived surface stoichiometries. The Ar + ion energy and the ion dose affected not only the surface composition of the treated films but also the graft copolymerization efficiency of the corresponding pretreated films

Pickering emulsion stabilized by cashew gum- poly-l-lactide copolymer nanoparticles: Synthesis, characterization and amphotericin B encapsulation.

Science.gov (United States)

Richter, A R; Feitosa, J P A; Paula, H C B; Goycoolea, F M; de Paula, R C M

2018-04-01

In this work, we provide proof-of-concept of formation, physical characteristics and potential use as a drug delivery formulation of Pickering emulsions (PE) obtained by a novel method that combines nanoprecipitation with subsequent spontaneous emulsification process. To this end, pre-formed ultra-small (d.∼10 nm) nanoprecipitated nanoparticles of hydrophobic derivatives of cashew tree gum grafted with polylactide (CGPLAP), were conceived to stabilize Pickering emulsions obtained by spontaneous emulsification. These were also loaded with Amphotericin B (AmB), a drug of low oral bioavailability used in the therapy of neglected diseases such as leishmaniasis. The graft reaction was performed in two CG/PLA molar ratio conditions (1:1 and 1:10). Emulsions were prepared by adding the organic phase (Miglyol 812 ® ) in the aqueous phase (nanoprecipitated CGPLAP), resulting the immediate emulsion formation. The isolation by centrifugation does not destabilize or separate the nanoparticles from oil droplets of the PE emulsion. Emulsions with CGPLAP 1:1 presented unimodal distributions at different CGPLA concentration, lower values in size and PDI and the best stability over time. The AmB was incorporated in the emulsions with a process efficiency of 21-47%, as determined by UV-vis. AmB in CGPLAP emulsions is in less aggregated state than observed in commercial AmB formulation. Copyright © 2018 Elsevier B.V. All rights reserved.

Novel star-type methoxy-poly(ethylene glycol) (PEG)–poly(ε-caprolactone) (PCL) copolymeric nanoparticles for controlled release of curcumin

International Nuclear Information System (INIS)

Feng Runliang; Zhu Wenxia; Song Zhimei; Zhao Liyan; Zhai Guangxi

2013-01-01

To improve curcumin’s (CURs) water solubility and release property, a novel star methoxy poly(ethylene glycol)–poly(ε-caprolactone) (MPEG–PCL) copolymer was synthesized through O-alkylation, basic hydrolysis and ring-opening polymerization reaction with MPEG, epichlorohydrin, and ε-caprolactone as raw materials. The structure of the novel copolymer was characterized by 1 H NMR, FT-IR, and GPC. The results of FT-IR and differential scanning calorimeter of CUR-loaded nanoparticles (NPs) prepared by dialysis method showed that CUR was successfully encapsulated into the SMP12 copolymeric NPs with 98.2 % of entrapment efficiency, 10.91 % of drug loading, and 88.4 ± 11.2 nm of mean particle diameter in amorphous forms. The dissolubility of nanoparticulate CUR was increased by 1.38 × 10 5 times over CUR in water. The obtained blank copolymer showed no hemolysis. A sustained CUR release to a total of approximately 56.13 % was discovered from CUR-NPs in 40 % of ethanol saline solution within 72 h on the use of dialysis method. The release behavior fitted the ambiexponent and biphasic kinetics equation. In conclusion, the copolymeric NPs loading CUR might serve as a potential nanocarrier to improve the solubility and release property of CUR.

Mathematical Modeling for the Extraction of Uranium and Molybdenum with Emulsion Liquid Membrane, Including Industrial Application and Cost Evaluation of the Uranium Recovery

International Nuclear Information System (INIS)

Kris Tri Basuki

2008-01-01

Emulsion liquid membrane systems are double emulsion drops. Two immiscible phases are separated by a third phase which is immiscible with the other two phases. The liquid membrane systems were classified into two types: (1) carrier mediated mass transfer, (2) mass transfer without any reaction involved. Uranium extraction, molybdenum extraction and solvent extraction were used as purposed elements for each type of the membrane systems in the derivation of their mathematical models. Mass transfer in emulsion liquid membrane (ELM) systems has been modeled by several differential and algebraic equations. The models take into account the following : mass transfer of the solute from the bulk external phase to the external phase-membrane interface; an equilibrium reaction between the solute and the carrier to form the solute-carrier complex at the interface; mass transfer by diffusion of the solute-carrier complex in the membrane phase to the membrane-internal phase interface; another equilibrium reaction of the solute-carrier complex to release the solute at the membrane-internal phase interface into the internal phase. Models with or without the consideration of film resistances were developed and compared. The models developed in this study can predict the extraction rate through emulsion liquid membranes theoretically. All parameters required in the models can be determined before an experimental extraction run. Experimental data from literature (uranium extraction) and (molybdenum extraction and solvent extraction) were used to test the models. The agreements between the theoretical predictions and the experimental data were very good. The advantages of emulsion liquid membrane systems over traditional methods were discussed. The models developed in this research can be used directly for the design of emulsion liquid membrane systems. The results of this study represent a very significant step toward the practical applications of the emulsion liquid membrane

A Comparative Study of the Physicochemical Properties of a Virgin Coconut Oil Emulsion and Commercial Food Supplement Emulsions

Directory of Open Access Journals (Sweden)

Yih Phing Khor

2014-07-01

Full Text Available Food manufacturers are interested in developing emulsion-based products into nutritional foods by using beneficial oils, such as fish oil and virgin coconut oil (VCO. In this study, the physicochemical properties of a VCO oil-in-water emulsion was investigated and compared to other commercial oil-in-water emulsion products (C1, C2, C3, and C4. C3 exhibited the smallest droplet size of 3.25 µm. The pH for the emulsion samples ranged from 2.52 to 4.38 and thus were categorised as acidic. In a texture analysis, C2 was described as the most firm, very adhesive and cohesive, as well as having high compressibility properties. From a rheological viewpoint, all the emulsion samples exhibited non-Newtonian behaviour, which manifested as a shear-thinning property. The G'G'' crossover illustrated by the VCO emulsion in the amplitude sweep graph but not the other commercial samples illustrated that the VCO emulsion had a better mouthfeel. In this context, the VCO emulsion yielded the highest zeta potential (64.86 mV, which was attributed to its strong repulsive forces, leading to a good dispersion system. C2 comprised the highest percentage of fat among all emulsion samples, followed by the VCO emulsion, with 18.44% and 6.59%, respectively.

Emulsions from Aerosol Sprays

Science.gov (United States)

Hengelmolen; Vincent; Hassall

1997-12-01

An electrostatic emulsification apparatus has been designed for the purpose of studying diffusion from oil droplets which have a mean size in the range of approximately 1.5-3.5 &mgr;m, with standard deviations of 40-50%. The emulsification technique involves the collection of a spray of electrically charged oil droplets onto a rotating water film which is sustained from a reservoir. In this way, emulsions with volume fractions of approximately 10(-3) are produced within several minutes at oil flow rates of around 10(-2) ml min-1. Phase-Doppler anemometry (PDA) was used to assess droplet size distributions for the sprays and emulsions. Results show that the mean emulsion droplet size was smaller than the mean spray droplet size by several orders of magnitude. At flow rates around 10(-2) ml min-1, the spray droplet size distribution was little affected by the applied potential between about -4.20 and -4.65 kV (mean droplet size between approximately 7.6 and 7.8 &mgr;m, with standard deviations of approximately 20%), whereas the mean droplet size of the corresponding emulsion decreased more rapidly with applied potential. Above an applied potential of approximately -4.30 kV, which corresponded to an emulsion droplet size below approximately 2 &mgr;m, the measured volume fraction of the emulsion decreased with respect to the volume fraction as calculated on the basis of total amount of injected oil. Copyright 1997 Academic Press. Copyright 1997Academic Press

Kinetics of Crystallization in Polydisperse Emulsions.

Science.gov (United States)

Kashchiev; Kaneko; Sato

1998-12-01

The kinetics of isothermal crystallization of the droplets in polydisperse emulsions are analyzed under the condition that each emulsion droplet gives birth to one nucleus only. Expressions are derived for the time dependences of the number of crystallized droplets and the fraction of crystallized droplet volume in the cases of either volume or surface nucleation of the crystals in the droplets. The time for half-crystallization is determined as a function of the emulsion polydispersity, and it is found that the more polydisperse the emulsion, the shorter this time in comparison with that for the corresponding monodisperse emulsion. Formulae are also obtained for the change of the velocity Kv of propagation of ultrasound through polydisperse emulsions during the time t of isothermal crystallization of the droplets in them. Good agreement is found between theory and experiment in an analysis of available Kv(t) data for crystallization in polydisperse palm oil-in-water and n-hexadecane-in-water emulsions. The results obtained are directly applicable to devitrification and polymorphic transformation of disperse solid phases. Copyright 1998 Academic Press.

Steroidal Compounds in Commercial Parenteral Lipid Emulsions

Science.gov (United States)

Xu, Zhidong; Harvey, Kevin A.; Pavlina, Thomas; Dutot, Guy; Hise, Mary; Zaloga, Gary P.; Siddiqui, Rafat A.

2012-01-01

Parenteral nutrition lipid emulsions made from various plant oils contain steroidal compounds, called phytosterols. During parenteral administration of lipid emulsions, phytosterols can reach levels in the blood that are many fold higher than during enteral administration. The elevated phytosterol levels have been associated with the development of liver dysfunction and the rare development of liver failure. There is limited information available in the literature related to phytosterol concentrations in lipid emulsions. The objective of the current study was to validate an assay for steroidal compounds found in lipid emulsions and to compare their concentrations in the most commonly used parenteral nutrition lipid emulsions: Liposyn® II, Liposyn® III, Lipofundin® MCT, Lipofundin® N, Structolipid®, Intralipid®, Ivelip® and ClinOleic®. Our data demonstrates that concentrations of the various steroidal compounds varied greatly between the eight lipid emulsions, with the olive oil-based lipid emulsion containing the lowest levels of phytosterols and cholesterol, and the highest concentration of squalene. The clinical impression of greater incidences of liver dysfunction with soybean versus MCT/LCT and olive/soy lipid emulsions may be reflective of the levels of phytosterols in these emulsions. This information may help guide future studies and clinical care of patients with lipid emulsion-associated liver dysfunction. PMID:23016123

Steroidal compounds in commercial parenteral lipid emulsions.

Science.gov (United States)

Xu, Zhidong; Harvey, Kevin A; Pavlina, Thomas; Dutot, Guy; Hise, Mary; Zaloga, Gary P; Siddiqui, Rafat A

2012-08-01

Parenteral nutrition lipid emulsions made from various plant oils contain steroidal compounds, called phytosterols. During parenteral administration of lipid emulsions, phytosterols can reach levels in the blood that are many fold higher than during enteral administration. The elevated phytosterol levels have been associated with the development of liver dysfunction and the rare development of liver failure. There is limited information available in the literature related to phytosterol concentrations in lipid emulsions. The objective of the current study was to validate an assay for steroidal compounds found in lipid emulsions and to compare their concentrations in the most commonly used parenteral nutrition lipid emulsions: Liposyn(®) II, Liposyn(®) III, Lipofundin(®) MCT, Lipofundin(®) N, Structolipid(®), Intralipid(®), Ivelip(®) and ClinOleic(®). Our data demonstrates that concentrations of the various steroidal compounds varied greatly between the eight lipid emulsions, with the olive oil-based lipid emulsion containing the lowest levels of phytosterols and cholesterol, and the highest concentration of squalene. The clinical impression of greater incidences of liver dysfunction with soybean versus MCT/LCT and olive/soy lipid emulsions may be reflective of the levels of phytosterols in these emulsions. This information may help guide future studies and clinical care of patients with lipid emulsion-associated liver dysfunction.

Electrochemically driven emulsion inversion

Science.gov (United States)

Johans, Christoffer; Kontturi, Kyösti

2007-09-01

It is shown that emulsions stabilized by ionic surfactants can be inverted by controlling the electrical potential across the oil-water interface. The potential dependent partitioning of sodium dodecyl sulfate (SDS) was studied by cyclic voltammetry at the 1,2-dichlorobenzene|water interface. In the emulsion the potential control was achieved by using a potential-determining salt. The inversion of a 1,2-dichlorobenzene-in-water (O/W) emulsion stabilized by SDS was followed by conductometry as a function of added tetrapropylammonium chloride. A sudden drop in conductivity was observed, indicating the change of the continuous phase from water to 1,2-dichlorobenzene, i.e. a water-in-1,2-dichlorobenzene emulsion was formed. The inversion potential is well in accordance with that predicted by the hydrophilic-lipophilic deviation if the interfacial potential is appropriately accounted for.

Stable and pH-responsive core-shell nanoparticles based on HEC and PMAA networks via template copolymerization

Science.gov (United States)

Zhang, Y.; Jin, Q.; Chen, Y.; Zhao, J.

2011-10-01

Taking advantage of the specific hydrogen bonding interactions, stable and pH-responsive core-shell nanoparticles based on hydroxyethyl cellulose (HEC) and polymethacrylic acid (PMAA) networks, with a size ranging from 190 to 250 nm, can be efficiently prepared via facile one-step co-polymerization of methacrylic acid (MAA) and N, N'-methylenebisacrylamide (MBA) on HEC template in water. Using dynamic light scattering, electrophoretic light scattering, fluorescence spectrometry, thermo-gravimetric analysis, TEM, and AFM observations, the influence of crosslinker MBA as well as the reaction parameters were studied. The results show that after the introduction of crosslinker MBA, the nanoparticles became less compact; their size exhibited a smaller pH sensitivity, and their stability against pH value was improved greatly. Furthermore, the size, structure, and pH response of the nanoparticles can be adjusted via varying the reaction parameters: nanoparticles of smaller size, more compact structure, and higher swelling capacity were produced as pH value of the reaction medium increased or the HEC/MAA ratio decreased; while nanoparticles of smaller size, less compact structure and smaller swelling capacity were produced as the total feeding concentration increased.

On the production of shower particles from light (Cno) and heavy (Ag Br) emulsion nuclei at Dubna energy

International Nuclear Information System (INIS)

EI-Nagdy, M.S.; Abdel-Waged, Kh; Abdel-Halim, S.M.; Khalil, E.I.

2000-01-01

The reaction cross sections for p, d, He, C, Mg and S beams with different chemical components of emulsion nuclei at 4.5 A GeV/c have been studied with high statistics, and were compared with the calculations according to Glauber model. The multiplicity distributions of shower produced particles from these interactions with light and heavy emulsion nuclei are analyzed in terms of the negative binomial and Poisson distribution laws

Polyfunctional monomers as additives for enhancing the radiation copolymerization of styrene with polyethylene, polypropylene, and PVC

International Nuclear Information System (INIS)

Ang, C.H.; Garnett, J.L.; Levot, R.; Long, M.A.

1982-01-01

Additives which can increase the yield in the radiation grafting of monomers to polymers are useful. The use of polyfunctional monomers as additives (approx. = 1% v/v) are shown to enhance significantly the copolymerization yields of styrene in methanol to films of polyethylene and polypropylene under certain radiation conditions. The results obtained when the polyolefins are replaced by PVC as backbone polymer in these accelerated grafting reactions are reported. Divinylbenzene (DVB) and trimethylolpropane triacrylate (TMPTA) were used as representative polyfunctional monomers for the enhancement effect. When polypropylene was used as backbone polymer, the inclusion of DVB significantly enhanced the radiation grafting of styrene in methanol at all monomer concentrations studied above 35%. At certain monomer concentrations (50% , 60%), the yield of graft copolymer was almost doubled by the addition of DVB. 3 tables. (DP)

Study of the diffusion of some emulsions in the human skin by pulsed photoacoustic spectroscopy

International Nuclear Information System (INIS)

Lahjomri, F; Benamar, N; Chatri, E; Leblanc, R M

2003-01-01

We previously used pulsed photoacoustic spectroscopy (PPAS) to quantify sunscreen diffusion into human skin, and suggested a methodology to evaluate the time and the depth diffusion profile. These results were obtained by the analysis of the photoacoustic maximum response signal P max decrease, the time delay t max and the Fourier transform representation of the photoacoustic signal. In this study we present the results obtained for diffusion of four typical emulsions used in sunscreen compositions that show, for the first time, a particular behaviour for one of these emulsions due to a chemical reaction inside the skin during the diffusion process. This result provides a particularly interesting technique through the PPAS, to evaluate in situ the eventual chemical reactions that can occur during drug diffusion into human skin

Anisotropic and correlated emissions of short range charged particles in anti pAg/Br reactions at 1. 4 GeV/c incident momentum observed in photographic emulsions

Energy Technology Data Exchange (ETDEWEB)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1984-07-01

Anti pAg/Br reactions at 1.4 GeV/c incident momentum are studied by means of the emulsion technique. A group of short range charged particles is observed. For the events with one short track, a backward and transversal emission is seen, which probably is due to some very fast process. For the events with two short tracks, a back-to-back emission is seen, indicating some two-body decay, where the target nucleus possibly behaves spectator-like.

Anisotropic and correlated emissions of short range charged particles in anti pAg/Br reactions at 1.4 GeV/c incident momentum observed in photographic emulsions

International Nuclear Information System (INIS)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1984-01-01

Anti pAg/Br reactions at 1.4 GeV/c incident momentum are studied by means of the emulsion technique. A group of short range charged particles is observed. For the events with one short track, a backward and transversal emission is seen, which probably is due to some very fast process. For the events with two short tracks, a back-to-back emission is seen, indicating some two-body decay, where the target nucleus possibly behaves spectator-like. (Auth.)

Study on some characteristics of nuclear emulsions

Energy Technology Data Exchange (ETDEWEB)

Yonglian, Liu; Jinqin, Han; Huichang, Liu [Academia Sinica, Beijing, BJ (China). Inst. of Atomic Energy

1993-11-01

The authors describe the variation of some characteristics of the nuclear emulsion such as sensitivity, fog density and latent image stability influenced by adding ascorbic acid into the finished emulsion N-4. A comparative study of latent image stability is made between Fuji ET-7B nuclear emulsion and authors' under different temperature and relative humidity. The result indicates that the addition of ascorbic acid obviously improves the latent image stability of the emulsion N-4. The Fuji ET-7B emulsion and the emulsion N-4 containing ascorbic acid have similar latent image fading quality at lower temperature while the Japanese sample does have better quality at room temperature.

Bioreactor droplets from liposome-stabilized all-aqueous emulsions

Science.gov (United States)

Dewey, Daniel C.; Strulson, Christopher A.; Cacace, David N.; Bevilacqua, Philip C.; Keating, Christine D.

2014-08-01

Artificial bioreactors are desirable for in vitro biochemical studies and as protocells. A key challenge is maintaining a favourable internal environment while allowing substrate entry and product departure. We show that semipermeable, size-controlled bioreactors with aqueous, macromolecularly crowded interiors can be assembled by liposome stabilization of an all-aqueous emulsion. Dextran-rich aqueous droplets are dispersed in a continuous polyethylene glycol (PEG)-rich aqueous phase, with coalescence inhibited by adsorbed ~130-nm diameter liposomes. Fluorescence recovery after photobleaching and dynamic light scattering data indicate that the liposomes, which are PEGylated and negatively charged, remain intact at the interface for extended time. Inter-droplet repulsion provides electrostatic stabilization of the emulsion, with droplet coalescence prevented even for submonolayer interfacial coatings. RNA and DNA can enter and exit aqueous droplets by diffusion, with final concentrations dictated by partitioning. The capacity to serve as microscale bioreactors is established by demonstrating a ribozyme cleavage reaction within the liposome-coated droplets.

Steroidal Compounds in Commercial Parenteral Lipid Emulsions

Directory of Open Access Journals (Sweden)

Rafat A. Siddiqui

2012-08-01

Full Text Available Parenteral nutrition lipid emulsions made from various plant oils contain steroidal compounds, called phytosterols. During parenteral administration of lipid emulsions, phytosterols can reach levels in the blood that are many fold higher than during enteral administration. The elevated phytosterol levels have been associated with the development of liver dysfunction and the rare development of liver failure. There is limited information available in the literature related to phytosterol concentrations in lipid emulsions. The objective of the current study was to validate an assay for steroidal compounds found in lipid emulsions and to compare their concentrations in the most commonly used parenteral nutrition lipid emulsions: Liposyn^® II, Liposyn^® III, Lipofundin^® MCT, Lipofundin^® N, Structolipid^®, Intralipid^®, Ivelip^® and ClinOleic^®. Our data demonstrates that concentrations of the various steroidal compounds varied greatly between the eight lipid emulsions, with the olive oil-based lipid emulsion containing the lowest levels of phytosterols and cholesterol, and the highest concentration of squalene. The clinical impression of greater incidences of liver dysfunction with soybean versus MCT/LCT and olive/soy lipid emulsions may be reflective of the levels of phytosterols in these emulsions. This information may help guide future studies and clinical care of patients with lipid emulsion-associated liver dysfunction.

Characterisation of Microbial Cellulose Modified by Graft Copolymerization Technique

International Nuclear Information System (INIS)

Tita Puspitasari; Cynthia Linaya Radiman

2008-01-01

Chemical and phisycal modifications of polymer can be carried out by radiation induced graft copolymerization. This research was carried out to study the morphology and crystallinity of microbial cellulose copolymer grafted by acrylic acid (MC-g-AAC). The SEM microstructural analysis proved that the acrylic acid could diffuse into the microbial celullose and resulted a dense structure. Crystallinity measurement showded that the crystalinity of microbial cellulose increase from 50 % to 53 % after modification. (author)

Synthesis of Covalently Cross-Linked Colloidosomes from Peroxidized Pickering Emulsions

Directory of Open Access Journals (Sweden)

Nadiya Popadyuk

2016-10-01

Full Text Available A new approach to the formation of cross-linked colloidosomes was developed on the basis of Pickering emulsions that were stabilized exclusively by peroxidized colloidal particles. Free radical polymerization and a soft template technique were used to convert droplets of a Pickering emulsion into colloidosomes. The peroxidized latex particles were synthesized in the emulsion polymerization process using amphiphilic polyperoxide copolymers poly(2-tert-butylperoxy-2-methyl-5-hexen-3-ine-co-maleic acid (PM-1-MAc or poly[N-(tert-butylperoxymethylacrylamide]-co-maleic acid (PM-2-MAc, which were applied as both initiators and surfactants (inisurfs. The polymerization in the presence of the inisurfs results in latexes with a controllable amount of peroxide and carboxyl groups at the particle surface. Peroxidized polystyrene latex particles with a covalently grafted layer of inisurf PM-1-MAc or PM-2-MAc were used as Pickering stabilizers to form Pickering emulsions. A mixture of styrene and/or butyl acrylate with divinylbenzene and hexadecane was applied as a template for the synthesis of colloidosomes. Peroxidized latex particles located at the interface are involved in the radical reactions of colloidosomes formation. As a result, covalently cross-linked colloidosomes were obtained. It was demonstrated that the structure of the synthesized (using peroxidized latex particles colloidosomes depends on the amount of functional groups and pH during the synthesis. Therefore, the size and morphology of colloidosomes can be controlled by latex particle surface properties.

Modulation of Cyclodextrin Particle Amphiphilic Properties to Stabilize Pickering Emulsion.

Science.gov (United States)

Xi, Yongkang; Luo, Zhigang; Lu, Xuanxuan; Peng, Xichun

2018-01-10

Cyclodextrins have been proven to form complexes with linear oil molecules and stabilize emulsions. Amphiphilic properties of cyclodextrin particles were modulated through esterification reaction between β-cyclodextrin (β-CD) and octadecenyl succinic anhydride (ODSA) under alkaline conditions. ODS-β-CD particles with degree of substitution (DS) of 0.003, 0.011, and 0.019 were obtained. The introduced hydrophobic long chain that was linked within β-CD cavity led to the change of ODS-β-CD in terms of morphological structure, surface charge density, size, and contact angle, upon which the properties and stability of the emulsions stabilized by ODS-β-CD were highly dependent. The average diameter of ODS-β-CD particles ranged from 449 to 1484 nm. With the DS increased from 0.003 to 0.019, the contact angle and absolute zeta potential value of these ODS-β-CD particles improved from 25.7° to 47.3° and 48.1 to 62.8 mV, respectively. The cage structure of β-CD crystals was transformed to channel structure, then further to amorphous structure after introduction of the octadecenyl succinylation chain. ODS-β-CD particles exhibited higher emulsifying ability compared to β-CD. The resulting Pickering emulsions formed by ODS-β-CD particles were more stable during storage. This study investigates the ability of these ODS-β-CD particles to stabilize oil-in-water emulsions with respect to their amphiphilic character and structural properties.

[Are there pseudophototropic reactions in biology? Part 4: On the reversibility of biologic/synthetic polymere systems (author's transl)].

Science.gov (United States)

Patschorke, J

1979-01-01

In further research on pseudophototropic behaviour in cellular membranes of halobacteria the reversibility of vinylmethylethermaleic anhydride-copolymeres with biological liquids is tested and the basic principles of different colour generating reactions are studied.

Optimal control of batch emulsion polymerization of vinyl chloride

Energy Technology Data Exchange (ETDEWEB)

Damslora, Andre Johan

1998-12-31

The highly exothermic polymerization of vinyl chloride (VC) is carried out in large vessels where the heat removal represents a major limitation of the production rate. Many emulsion polymerization reactors are operated in such a way that a substantial part of the heat transfer capacity is left unused for a significant part of the total batch time. To increase the reaction rate so that it matches the heat removal capacity during the course of the reaction, this thesis proposes the use of a sufficiently flexible initiator system to obtain a reaction rate which is high throughout the reaction and real-time optimization to compute the addition policy for the initiator. This optimization based approach provides a basis for an interplay between design and control and between production and research. A simple model is developed for predicting the polymerization rate. The model is highly nonlinear and open-loop unstable and may serve as an interesting case for comparison of nonlinear control strategies. The model is fitted to data obtained in a laboratory scale reactor. Finally, the thesis discusses optimal control of the emulsion polymerization reactor. Reduction of the batch cycle time is of major economic importance, as long as the quality parameters are within their specifications. The control parameterization had a major influence on the performance. A differentiable spline parameterization was applied and the optimization is illustrated in a number of cases. The best performance is obtained when the reactor temperature is obtained when the optimization is combined with some form of closed-loop control of the reactor temperature. 112 refs., 48 figs., 4 tabs.

Development of novel zein-sodium caseinate nanoparticle (ZP)-stabilized emulsion films for improved water barrier properties via emulsion/solvent evaporation.

Science.gov (United States)

Wang, Li-Juan; Yin, Ye-Chong; Yin, Shou-Wei; Yang, Xiao-Quan; Shi, Wei-Jian; Tang, Chuan-He; Wang, Jin-Mei

2013-11-20

This work attempted to develop novel high barrier zein/SC nanoparticle (ZP)-stabilized emulsion films through microfluidic emulsification (ZPE films) or in combination with solvent (ethyl acetate) evaporation techniques (ZPE-EA films). Some physical properties, including tensile and optical properties, water vapor permeability (WVP), and surface hydrophobicity, as well as the microstructure of ZP-stabilized emulsion films were evaluated and compared with SC emulsion (SCE) films. The emulsion/solvent evaporation approach reduced lipid droplets of ZP-stabilized emulsions, and lipid droplets of ZP-stabilized emulsions were similar to or slightly lower than that of SC emulsions. However, ZP- and SC-stabilized emulsion films exhibited a completely different microstructure, nanoscalar lipid droplets were homogeneously distributed in the ZPE film matrix and interpenetrating protein-oil complex networks occurred within ZPE-EA films, whereas SCE films presented a heterogeneous microstructure. The different stabilization mechanisms against creaming or coalescence during film formation accounted for the preceding discrepancy of the microstructures between ZP-and SC-stabilized emulsion films. Interestingly, ZP-stabilized emulsion films exhibited a better water barrier efficiency, and the WVP values were only 40-50% of SCE films. A schematic representation for the formation of ZP-stabilized emulsion films was proposed to relate the physical performance of the films with their microstructure and to elucidate the possible forming mechanism of the films.

Microfluidic methods to study emulsion formation

NARCIS (Netherlands)

Muijlwijk, Kelly

2017-01-01

Emulsions are dispersions of one liquid in another that are commonly used in various products, and methods such as high-pressure homogenisers and colloid mills are used to form emulsions. The size and size distribution of emulsion droplets are important for the final product properties and thus

Emprego de catalisadores à base de níquel para homo- e copolimerização de estireno The use of nickel-based catalysts for homo-and copolymerization of styrene

Directory of Open Access Journals (Sweden)

Luis Carlos Ferreira Jr.

2004-12-01

Full Text Available This review deals with the homo- and copolymerization of styrene with nickel catalysts. The catalytic activity, polymer stereoregularity, polymer molecular weight and polydispersity are dependent upon nickel ligands and reaction parameters. Catalysts supported on silica, treated with methylaluminoxane (MAO, have shown higher stereospecificity and activity compared to homogeneous ones. The influence of these parameters is discussed focusing on the elucidation of some aspects of the polymerization mechanism.

Graft copolymerization of styrene onto poly(vinyl alcohol) initiated by potassium diperiodatocuprate (III)

International Nuclear Information System (INIS)

Bai, L.; Wang, Ch.; Jin, J.; Liu, Y.

2009-01-01

The graft copolymerization of styrene onto poly(vinyl alcohol) is studied by using a novel redox system of potassium diperiodatocuprate-poly(vinyl alcohol) (Cu(III)poly(vinyl alcohol) in alkaline medium. Cu(III)-poly(vinyl alcohol) redox pair is an efficient initiator for this graft copolymerization which is proved by high graft efficiency (>97%) and high percentage of graft (>300%). Reaction conditions (monomer-to-poly(vinyl alcohol) weight ratio, initiator concentration, p H, time and temperature) affect the graft parameters which have been investigated systematically. The optimum reaction conditions are found as St/poly(vinyl alcohol) = 5.4; [Cu(III)] = 1*10 -2 M; p H = 12.7; temperature = 50 d eg C ; time = 3.5 h. Further, the equation of the overall polymerization rate can be written as follows: R p = k C 1.9 (St) C 1.7 (Cu(III)). The overall activation energy was calculated to be 42.0 kJ/mol based on the experimental data of the relations between R p and C(St); R p and C(Cu(III)); and R p and temperature. A mechanism is proposed to explain the formation of radicals and the initiation. The structure of the graft copolymers is confirmed by Fourier transfer infrared spectroscopy. Some peaks were compared with poly(vinyl alcohol) at 3080.34-3001.79 cm -1 (=C-H stretching in the phenyl ring), 1600.34-1450.95 cm -1 (C=C stretching in the phenyl ring), 755.17 cm -1 and 698.64 cm -1 (=C-H out-off-plane bending in phenyl ring) which are considered to belong to the characteristic absorption bands of phenyl group of polystyrene. Therefore it proves that the graft copolymer is composed of poly(vinyl alcohol) and polystyrene. thermal gravimetric analysis thermo grams of poly(vinyl alcohol) and poly(vinyl alcohol)-graft-polystyrene are investigated as well. As it is shown the initial decomposition temperature of poly(vinyl alcohol)-g-polystyrene(377.3 d eg C ) is much higher than that of poly(vinyl alcohol) (241.8 d eg C ), which indicates that the thermal stability of the

Modelling of Emulsion Flow in Porous Media

Energy Technology Data Exchange (ETDEWEB)

Abou-Kassem, J.H. [UAE University (United Arab Emirates); Farouq Ali, S.M. [UAE University (United Arab Emirates)

1995-06-01

Oil recovery methods predominantly involve emulsion formation. Oil recovery simulation requires the incorporation of emulsion characteristics and flow in porous media, in order to optimize oil recovery from petroleum reservoirs. This paper explored the nature and rheology of emulsions, and evaluated several models of flow of Newtonian and non-Newtonian fluids in porous media. It also summarized in situ emulsion formation in porous media. A model for both Newtonian and non-Newtonian emulsion fluid flow was proposed, with special emphasis on pore size, and tortuosity in the porous media.

Nanocellulose-stabilized Pickering emulsions and their applications.

Science.gov (United States)

Fujisawa, Shuji; Togawa, Eiji; Kuroda, Katsushi

2017-01-01

Pickering emulsion, which is an emulsion stabilized by solid particles, offers a wide range of potential applications because it generally provides a more stable system than surfactant-stabilized emulsion. Among various solid stabilizers, nanocellulose may open up new opportunities for future Pickering emulsions owing to its unique nanosizes, amphiphilicity, and other favorable properties (e.g. chemical stability, biodegradability, biocompatibility, and renewability). In this review, the preparation and properties of nanocellulose-stabilized Pickering emulsions are summarized. We also provide future perspectives on their applications, such as drug delivery, food, and composite materials.

Polyacrylates with High Biomass Contents for Pressure-Sensitive Adhesives Prepared via Mini-emulsion Polymerization

Science.gov (United States)

Gang Pu; Matthew R. Dubay; Jiguang Zhang; Steven J. Severtson; Carl J. Houtman

2012-01-01

n-Butyl acrylate and other acrylic monomers were copolymerized with an acrylated macromonomer to produce polymers for pressure-sensitive adhesive (PSA) applications. Macromonomers were generated through the ring-opening copolymerization of L-lactide and ε-caprolactone with 2-hydroxyethyl...

Heterogeneous Pd catalysts as emulsifiers in Pickering emulsions for integrated multistep synthesis in flow chemistry.

Science.gov (United States)

Hiebler, Katharina; Lichtenegger, Georg J; Maier, Manuel C; Park, Eun Sung; Gonzales-Groom, Renie; Binks, Bernard P; Gruber-Woelfler, Heidrun

2018-01-01

Within the "compartmentalised smart factory" approach of the ONE-FLOW project the implementation of different catalysts in "compartments" provided by Pickering emulsions and their application in continuous flow is targeted. We present here the development of heterogeneous Pd catalysts that are ready to be used in combination with biocatalysts for catalytic cascade synthesis of active pharmaceutical ingredients (APIs). In particular, we focus on the application of the catalytic systems for Suzuki-Miyaura cross-coupling reactions, which is the key step in the synthesis of the targeted APIs valsartan and sacubitril. An immobilised enzyme will accomplish the final product formation via hydrolysis. In order to create a large interfacial area for the catalytic reactions and to keep the reagents separated until required, the catalyst particles are used to stabilise Pickering emulsions of oil and water. A set of Ce-Sn-Pd oxides with the molecular formula Ce 0.99- x Sn x Pd 0.01 O 2-δ ( x = 0-0.99) has been prepared utilising a simple single-step solution combustion method. The high applicability of the catalysts for different functional groups and their minimal leaching behaviour is demonstrated with various Suzuki-Miyaura cross-coupling reactions in batch as well as in continuous flow employing the so-called "plug & play reactor". Finally, we demonstrate the use of these particles as the sole emulsifier of oil-water emulsions for a range of oils.

Studies of water-in-oil emulsions : testing of emulsion formation in OHMSETT

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.

2001-01-01

A study was conducted to determine the stability of water-in-oil emulsions in the OHMSETT tank facility. The results were then compared with previous laboratory studies which suggested that the stability of emulsions can be grouped into four categories, stable, unstable, meso-stable and entrained. It has been determined that entrained emulsions can retain oil by viscous forces long enough for interfacial agents, resins and asphaltenes to stabilize the droplets. This paper also described the difference in viscosity between the 4 categories of emulsion stability. The OHMSETT tests were conducted in two series of one week each. The first series of tests were conducted in July and involved 12 experiments on 2 different types of oils which were placed at varying thicknesses on the water. The second set of tests were conducted in November and involved 12 experiments on 6 oils. The rheological properties of the oils were measured and compared to the same oils undergoing emulsification in the laboratory. The oils and water-in-oil states produced were found to have analogous properties between the laboratory and the first set of tests at the OHMSETT facility. All the oils tested produced entrained water-in-oil states in both the laboratory and the test tank. The energy in the two test conditions was found to be similar, with the OHMSETT emulsions similar to one produced in the laboratory at high energies. The second series of tests at OHMSETT did not result in the expected water in-oil- states. This unexpected result was most likely due to the residual surfactant from an earlier dispersant experiment. The study showed that the conditions for emulsion formation are analogous in the OHMSETT tank and in the laboratory tests. The level of energy is considered to be the major variant. It was concluded that the energy levels between the laboratory mixing experiments and the OHMSETT is similar. It was shown that surfactants left over from dispersant testing inhibited the formation

Synthesis, Cyclopolymerization and Cyclo-Copolymerization of 9-(2-Diallylaminoethyladenine and Its Hydrochloride Salt

Directory of Open Access Journals (Sweden)

Karyn Usher

2012-11-01

Full Text Available We report herein the synthesis and characterization of 9-(2-diallylaminoethyl adenine. We evaluated two different synthetic routes starting with adenine where the optimal route was achieved through coupling of 9-(2-chloroethyladenine with diallylamine. The cyclopolymerization and cyclo-copolymerization of 9-(2-diallylaminoethyladenine hydrochloride salt resulted in low molecular weight oligomers in low yields. In contrast, 9-(2-diallylaminoethyladenine failed to cyclopolymerize, however, it formed a copolymer with SO2 in relatively good yields. The molecular weights of the cyclopolymers were around 1,700–6,000 g/mol, as estimated by SEC. The cyclo-copolymer was stable up to 226 °C. To the best of our knowledge, this is the first example of a free-radical cyclo-copolymerization of a neutral alkyldiallylamine derivative with SO2. These polymers represent a novel class of carbocyclic polynucleotides.

From water-in-oil to oil-in-water emulsions to optimize the production of fatty acids using ionic liquids in micellar systems.

Science.gov (United States)

Santos, Luísa D F; Coutinho, João A P; Ventura, Sónia P M

2015-01-01

Biocatalysis is nowadays considered as one of the most important tools in green chemistry. The elimination of multiple steps involved in some of the most complex chemical synthesis, reducing the amounts of wastes and hazards, thus increasing the reaction yields and decreasing the intrinsic costs, are the major advantages of biocatalysis. This work aims at improving the enzymatic hydrolysis of olive oil to produce valuable fatty acids through emulsion systems formed by long alkyl chain ionic liquids (ILs). The optimization of the emulsion and the best conditions to maximize the production of fatty acids were investigated. The stability of the emulsion was characterized considering the effect of several parameters, namely, the IL and its concentration and different water/olive oil volumetric ratios. ILs from the imidazolium and phosphonium families were evaluated. The results suggest that the ILs effect on the hydrolysis performance varies with the water concentration and the emulsion system formed, that is, water-in-oil or oil-in-water emulsion. Although at low water concentrations, the presence of ILs does not present any advantages for the hydrolysis reaction, at high water contents (in oil-in-water emulsions), the imidazolium-based IL acts as an enhancer of the lipase catalytic capacity, super-activating 1.8 times the enzyme, and consequently promoting the complete hydrolysis of the olive oil for the highest water contents [85% (v/v)]. © 2015 American Institute of Chemical Engineers.

Synthesis and optimization of EA-MMA copolymer emulsion%EA-MMA共聚乳液合成工艺及优化

Institute of Scientific and Technical Information of China (English)

张成芬; 武玉民

2011-01-01

以丙烯酸乙酯(EA)和甲基丙烯酸甲酯(MMA)为共聚单体、过硫酸钾(KPS)为引发剂、十二烷基硫酸钠(SDS)和壬基酚聚氧乙烯醚(OP-10)为复合乳化剂,采用乳液聚合法合成出一种稳定的EA-MMA乳液.通过单因素试验法考察了乳化剂浓度、引发剂浓度、反应温度和反应时间等因素对乳液平均粒径和单体转化率的影响,并采用正交试验法进一步优选出制备EA-MMA乳液的最佳工艺条件.结果表明:当w(乳化剂)=2.0%、w(引发剂)=0.60%、反应时间为4 h和反应温度为80℃时,制成的EA-MMA乳液较稳定,并且单体转化率相对最高.%With ethyl acrylate(EA) and methyl methacrylate( MMA) as comonomers ,potassium persulfate(KPS)as initiator,and sodium dodecyl sulfate(SDS) and nonylphenol ethoxylates(OP-10) as composite emulsifier,a stable EA-MMA emulsion was synthesized by emulsion polymerization. The influences of some factor(such as emulsifier concentration,initiator concentration,reaction temperature and reaction time) on average particle size of emulsion and monomer conversion rate were investigated by single factor experiment method,then the optimal process conditions of preparing EA-MMA emulsion were preferred by orthogonal experiment method. The results showed that the EA-MMA emulsion had better stability and relatively highest monomer conversion rate when the mass fractions of emulsifier and initiator were 2.0％ and 0.60％ respectively,the reaction time and reaction temperature were 4 h and 80 ℃ respectively.

Swelling and drug release behavior of poly(2-hydroxyethyl methacrylate/itaconic acid) copolymeric hydrogels obtained by gamma irradiation

International Nuclear Information System (INIS)

Tomic, S.Lj.; Micic, M.M.; Filipovic, J.M.; Suljovrujic, E.H.

2007-01-01

The new copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) were prepared by gamma irradiation, in order to examine the potential use of these hydrogels in controlled drug release systems. The influence of IA content in the gel on the swelling characteristics and the releasing behavior of hydrogels, and the effect of different drugs, theophylline (TPH) and fenethylline hydrochloride (FE), on the releasing behavior of P(HEMA/IA) matrix were investigated in vitro. The diffusion exponents for swelling and drug release indicate that the mechanisms of buffer uptake and drug release are governed by Fickian diffusion. The swelling kinetics and, therefore, the release rate depends on the matrix swelling degree. The drug release was faster for copolymeric hydrogels with a higher content of itaconic acid. Furthermore, the drug release for TPH as model drug was faster due to a smaller molecular size and a weaker interaction of the TPH molecules with(in) the P(HEMA/IA) copolymeric networks

Comparison of Polymer Networks Synthesized by Conventional Free Radical and RAFT Copolymerization Processes in Supercritical Carbon Dioxide

Directory of Open Access Journals (Sweden)

Patricia Pérez-Salinas

2017-05-01

Full Text Available There is a debate in the literature on whether or not polymer networks synthesized by reversible deactivation radical polymerization (RDRP processes, such as reversible addition-fragmentation radical transfer (RAFT copolymerization of vinyl/divinyl monomers, are less heterogeneous than those synthesized by conventional free radical copolymerization (FRP. In this contribution, the syntheses by FRP and RAFT of hydrogels based on 2-hydroxyethylene methacrylate (HEMA and ethylene glycol dimethacrylate (EGDMA in supercritical carbon dioxide (scCO2, using Krytox 157 FSL as the dispersing agent, and the properties of the materials produced, are compared. The materials were characterized by differential scanning calorimetry (DSC, swelling index (SI, infrared spectroscopy (FTIR and scanning electron microscopy (SEM. Studies on ciprofloxacin loading and release rate from hydrogels were also carried out. The combined results show that the hydrogels synthesized by FRP and RAFT are significantly different, with apparently less heterogeneity present in the materials synthesized by RAFT copolymerization. A ratio of experimental (Mcexp to theoretical (Mctheo molecular weight between crosslinks was established as a quantitative tool to assess the degree of heterogeneity of a polymer network.

Response of nuclear emulsions to ionizing radiations

International Nuclear Information System (INIS)

Katz, R.; Pinkerton, F.E.

1975-01-01

Heavy ion tracks in Ilford K-2 emulsion are simulated with a computer program which makes use of the delta-ray theory of track structure, and the special assumption that the response of this emulsion to gamma-rays is 8-or-more hit. The Ilford K-series of nuclear emulsions is produced from a parent stock called K.0 emulsion, sensitized to become K.1 to K.5, and desensitized to become K-1 to K-3. Our simulations demonstrate that the emulsions K.5 through K.0 to K-1 are 1-or-more hit detectors, while K-2 is an 8-or-more hit detector. We have no data for K-3 emulsion. It would appear that emulsions of intermediate hittedness might be produced by an intermediate desensitization, to mimic or match the RBE-LET variations of biological cells, perhaps to produce a ''rem-dosimeter''. In the K-2 emulsion no developable gains are produced by stopping H, He, and Li ions. The emulsion has ''threshold-like'' properties, resembling etchable track detectors. It should prove useful in the measurement of high LET dose in a strong low LET background, as for pions or neutrons. Since it can be expected to accumulate and repair ''sub-lethal damage'', to display the ion-kill and gamma-kill inactivation modes, the grain-count and track width regimes, it may serve to model biological effects. (auth)

Structured triglyceride emulsions in parenteral nutrition.

Science.gov (United States)

Chambrier, C; Lauverjat, M; Bouletreau, P

2006-08-01

Over the past 3 decades, various concepts for IV fat emulsions (IVFE) have been developed. A randomized, structured-lipid emulsion based on an old technology has recently become available. This structured-lipid emulsion is produced by mixing medium-chain triglycerides and long-chain triglycerides, then allowing hydrolysis to form free fatty acids, followed by random transesterification of the fatty acids into mixed triglyceride molecules. Studies in animals have shown an improvement in nitrogen balance with the use of these lipid emulsions. Only 8 human clinical studies with these products have been performed. The results of these human clinical studies have been less promising than the animal studies; however, an improvement in nitrogen balance and lipid metabolism exceeds results associated with infusion of long-chain triglycerides (LCT) or a physical mixture of long-chain triglycerides and medium-chain triglycerides (LCT-MCT). Structured-lipid emulsion seems to induce less elevation in serum liver function values compared with standard IVFEs. In addition, structured-lipid emulsions have no detrimental effect on the reticuloendothelial system. Further studies are necessary in order to recommend the use of structured-lipid emulsions. The clinical community hopes that chemically defined structured triglycerides will make it possible to determine the distribution of specific fatty acids on a specific position on the glycerol core and therefore obtain specific activity for a specific clinical situation.

Anisotropic and correlated emissions of short range charged particles in anti pAg/Br reactions of 1.4 GeV/c incident momentum observed in photographic emulsions

International Nuclear Information System (INIS)

Breivik, F.O.; Jacobsen, T.; Soerensen, S.O.

1983-12-01

Anti pAg/Br reactions at 1.4 GeV/c incident momentum were studied by means of the emulsion technique. A group of short range charged particles was observed. For the events with one short track, a backward and transversal emission was seen, probably due to some very fast process. For the events with two short tracks, a back-to-back emission was seen, indicating some two-body decay where the target nucleus possibly behaves spectator-like. The rates and forward collimations suggest that the same physical process causes the different multiplicities

Reaction of CO2 with propylene oxide and styrene oxide catalyzed by a chromium(III) amine-bis(phenolate) complex.

Science.gov (United States)

Dean, Rebecca K; Devaine-Pressing, Katalin; Dawe, Louise N; Kozak, Christopher M

2013-07-07

A diamine-bis(phenolate) chromium(III) complex, {CrCl[O2NN'](BuBu)}2 catalyzes the copolymerization of propylene oxide with carbon dioxide. The synthesis of this metal complex is straightforward and it can be obtained in high yields. This catalyst incorporates a tripodal amine-bis(phenolate) ligand, which differs from the salen or salan ligands typically used with Cr and Co complexes that have been employed as catalysts for the synthesis of such polycarbonates. The catalyst reported herein yields low molecular weight polymers with narrow polydispersities when the reaction is performed at room temperature. Performing the reaction at elevated temperatures causes the selective synthesis of propylene carbonate. The copolymerization activity for propylene oxide and carbon dioxide, as well as the coupling of carbon dioxide and styrene oxide to give styrene carbonate are presented.

Antioxidant activity and emulsion-stabilizing effect of pectic enzyme treated pectin in soy protein isolate-stabilized oil/water emulsion.

Science.gov (United States)

Huang, Ping-Hsiu; Lu, Hao-Te; Wang, Yuh-Tai; Wu, Ming-Chang

2011-09-14

The antioxidant activity of pectic enzyme treated pectin (PET-pectin) prepared from citrus pectin by enzymatic hydrolysis and its potential use as a stabilizer and an antioxidant for soy protein isolate (SPI)-stabilized oil in water (O/W) emulsion were investigated. Trolox equivalent antioxidant capacity (TEAC) was found to be positively associated with molecular weight (M(w)) of PET-pectin and negatively associated with degree of esterification (DE) of PET-pectin. PET-pectin (1 kDa and 11.6% DE) prepared from citrus pectin after 24 h of hydrolysis by commercial pectic enzyme produced by Aspergillus niger expressed higher α,α-diphenyl-β-picrylhydrazyl (DPPH) radical scavenging activity, TEAC, and reducing power than untreated citrus pectin (353 kDa and 60% DE). The addition of PET-pectin could increase both emulsifying activity (EA) and emulsion stability (ES) of SPI-stabilized O/W emulsion. When the SPI-stabilized lipid droplet was coated with the mixture of PET-pectin and pectin, the EA and ES of the emulsion were improved more than they were when the lipid droplet was coated with either pectin or PET-pectin alone. The amount of secondary oxidation products (thiobarbituric acid reactive substances) produced in the emulsion prepared with the mixture of SPI and PET-pectin was less than the amount produced in the emulsion prepared with either SPI or SPI/pectin. These results suggest that PET-pectin has an emulsion-stabilizing effect and lipid oxidation inhibition ability on SPI-stabilized emulsion. Therefore, PET-pectin can be used as a stabilizer as well as an antioxidant in plant origin in SPI-stabilized O/W emulsion and thus prolong the shelf life of food emulsion.

Preparation of Photoresponsive Functionalized Acrylic Nanoparticles Cantaining Carbazole Groups for Smart Cellulosic Papers

Directory of Open Access Journals (Sweden)

Jaber Keyvan Rad

2017-11-01

Full Text Available Photoresponsive functionalized polymer nanoparticles were prepared as useful materials for preparation of smart papers. Such polymer nanoparticles have wide applications in several fields including papers, sensors, bioimaging and biomedicine. First, carbazole as a photosensitive compound was modified with 2-bromoethanol through substitution nucleation reaction to its hydroxyl derivative (N-(2-hydroxyethyl carbazole, CzEtOH. The synthesis of 2-N-carbazolylethyl acrylate (CzEtA monomer was carried out by modification reaction of CzEtOH with acryloyl chloride and the chemical structures of the products were characterized. Next, CzEtA, methyl methacrylate (MMA and butyl acrylate were copolymerized to prepare photoresponsive functionalized polymer nanoparticles through mini-emulsion polymerization in order to form a hydrophobic core. This was followed by copolymerization of MMA and glycidyl methacrylate by seeded emulsion polymerization to give a functionalized outer layer on the latex particles. Absorption characteristics, size, size distribution (narrow size distribution and morphology of the nanoparticles were studied by ultraviolet-visible (UV-Vis spectroscopy, dynamic laser light scattering (DLS analysis and scanning electron microscopy (SEM micrographs, respectively. Finally, due to the importance of photoresponsive smart papers and their wide applications, cellulosic fibers were reacted with the prepared functionalized latex particles for preparation of smart papers. Morphology of the fibers was investigated with respect to the surface-immobilized polymers on the cellulosic paper and their smart behavior was evaluated by UV irradiation at 254 nm. The results revealed fast color changes and the obtained cellulosic papers became violet upon irradiation. This work shows some promising feature of these materials for preparation of anti-counterfeiting papers, where the safety becomes a major concern.

Selective Release of anti–TB Drugs Complex from Smart Copolymeric Bioactive nano–carriers

Directory of Open Access Journals (Sweden)

Alejandro Arredondo–Peñaranda

2014-07-01

Full Text Available Smart nano–copolymeric matrices have been employed to load and release anti tuberculosis (anti – TB drugs combinated complexes of Ethambutol (EMB, Isoniazid (INH, Rifampicin (RMP and Pyrazinamide (PZA. Copolymeric nanocarriers were synthesized using a microemulsion polymerization method previously reported. These nanocarriers can show selective swelling–collapse response under changes in local environments such a temperature, pH, solvent composition and electrical stimuli. The employ of these kinds of systems permits a controlled and selective delivery and release on specific human tissues. High Performance Liquid Chromatography technique was used to allow the detection of combinated mixtures of different active principles of anti–TB drugs using an acetonitrile mobile phase at 0.5 mL/min of flow rate whit a Spherisorb ODS2, C18 column. The results obtained suggest that the employ of smart nanohydrogels is a novel method in several tuberculosis therapies.

Effect of W/O Emulsion Fuel Properties on Spray Combustion

Science.gov (United States)

Ida, Tamio; Fuchihata, Manabu; Takeda, Shuuco

This study proposes a realizable technology for an emulsion combustion method that can reduce environmental loading. This paper discusses the effect on spray combustion for W/O emulsion fuel properties with an added agent, and the ratio between water and emulsifier added to a liquid fuel. The addition of water or emulsifier to a liquid fuel affected the spray combustion by causing micro-explosions in the flame due to geometric changes in the sprayed flame and changes to the temperature distribution. Experimental results revealed that the flame length shortened by almost 40% upon the addition of the water. Furthermore, it was found that water was effective in enhancing combustion due to its promoting micro-explosions. Results also showed that when the emulsifier was added to the spray flame, the additive burned in the flame's wake, producing a bright red flame. The flame length was observed to be long as a result. The micro-explosion phenomenon, caused by emulsifier dosage differences, was observed using time-dependent images at a generated frequency and an explosion scale with a high-speed photography method. Results indicated that the micro-explosion phenomenon in the W/O emulsion combustion method effectively promoted the combustion reaction and suppressed soot formation.

A novel headspace gas chromatographic method for in situ monitoring of monomer conversion during polymerization in an emulsion environment.

Science.gov (United States)

Chai, Xin-Sheng; Zhong, Jin-Feng; Hu, Hui-Chao

2012-05-18

This paper describes a novel multiple-headspace extraction/gas chromatographic (MHE-GC) technique for monitoring monomer conversion during a polymerization reaction in a water-based emulsion environment. The polymerization reaction of methyl methacrylate (MMA) in an aqueous emulsion is used as an example. The reaction was performed in a closed headspace sample vial (as a mini-reactor), with pentane as a tracer. In situ monitoring of the vapor concentration of the tracer, employing a multiple headspace extraction (sampling) scheme, coupled to a GC, makes it possible to quantitatively follow the conversion of MMA during the early stages of polymerization. Data on the integrated amount of the tracer vapor released from the monomer droplet phase during the polymerization is described by a mathematic equation from which the monomer conversion can be calculated. The present method is simple, automated and economical, and provides an efficient tool in the investigation of the reaction kinetics and effects of the reaction conditions on the early stage of polymerization. Copyright © 2012 Elsevier B.V. All rights reserved.

Enhancing saltiness in emulsion based foods

Directory of Open Access Journals (Sweden)

Lad Mita

2012-07-01

Full Text Available Abstract Background The concept of enhancing saltiness perception in emulsions and a liquid food formulated with the emulsions (ambient vegetable soup through increasing salt concentration in the continuous phase while retaining the fat content of the (aqueous continuous product was evaluated. This was accomplished by increasing the droplet phase volume using duplex emulsion technology. Viscosity and droplet size distribution was measured. Saltiness evaluation was based on simple paired comparison testing (2-Alternate Forced Choice tests, BS ISO 5495:2007. Results Single and duplex emulsions and emulsion-based products had comparable mean oil droplet diameters (25 to 30 μm; however, viscosity of the duplex emulsion systems was considerably higher. Sensory assessment of saltiness of emulsion pairs (2AFC indicated duplex technology enhanced saltiness perception compared to a single emulsion product at the same salt content (6.3 g/100 g in both simple emulsions and the formulated food product (P = 0.0596 and 0.0004 respectively although assessors noted the increased viscosity of the duplex systems. The formulated food product also contained pea starch particles which may have aided product mixing with saliva and thus accelerated tastant transport to the taste buds. Lowering salt content in the duplex systems (to levels of aqueous phase salt concentration similar to the level in the single systems resulted in duplex systems being perceived as less salty than the single system. It appears that the higher viscosity of the duplex systems could not be “overruled” by enhanced mixing through increased droplet phase volume at lowered salt content. Conclusions The results showed that salt reduction may be possible despite the added technology of duplex systems increasing the overall measured viscosity of the product. The changes in viscosity behavior impact mouthfeel, which may be exploitable in addition to the contribution towards salt

Emulsion properties of sunflower (Helianthus annuus) proteins

NARCIS (Netherlands)

Gonzalez-Perez, S.; Koningsveld, van G.A.; Vereijken, J.M.; Merck, K.B.; Gruppen, H.; Voragen, A.G.J.

2005-01-01

Emulsions were made with sunflower protein isolate (SI), helianthinin, and sunflower albumins (SFAs). Emulsion formation and stabilization were studied as a function of pH and ionic strength and after heat treatment of the proteins. The emulsions were characterized with respect to average droplet

Tuning Amphiphilicity of Particles for Controllable Pickering Emulsion

Directory of Open Access Journals (Sweden)

Zhen Wang

2016-11-01

Full Text Available Pickering emulsions with the use of particles as emulsifiers have been extensively used in scientific research and industrial production due to their edge in biocompatibility and stability compared with traditional emulsions. The control over Pickering emulsion stability and type plays a significant role in these applications. Among the present methods to build controllable Pickering emulsions, tuning the amphiphilicity of particles is comparatively effective and has attracted enormous attention. In this review, we highlight some recent advances in tuning the amphiphilicity of particles for controlling the stability and type of Pickering emulsions. The amphiphilicity of three types of particles including rigid particles, soft particles, and Janus particles are tailored by means of different mechanisms and discussed here in detail. The stabilization-destabilization interconversion and phase inversion of Pickering emulsions have been successfully achieved by changing the surface properties of these particles. This article provides a comprehensive review of controllable Pickering emulsions, which is expected to stimulate inspiration for designing and preparing novel Pickering emulsions, and ultimately directing the preparation of functional materials.

Destabilization of emulsions by natural minerals.

Science.gov (United States)

Yuan, Songhu; Tong, Man; Wu, Gaoming

2011-09-15

This study developed a novel method to destabilize emulsions and recycle oils, particularly for emulsified wastewater treatment. Natural minerals were used as demulsifying agents, two kinds of emulsions collected from medical and steel industry were treated. The addition of natural minerals, including artificial zeolite, natural zeolite, diatomite, bentonite and natural soil, could effectively destabilize both emulsions at pH 1 and 60 °C. Over 90% of chemical oxygen demand (COD) can be removed after treatment. Medical emulsion can be even destabilized by artificial zeolite at ambient temperature. The mechanism for emulsion destabilization by minerals was suggested as the decreased electrostatic repulsion at low pH, the enhanced gathering of oil microdroplets at elevated temperature, and the further decreased surface potential by the addition of minerals. Both flocculation and coalescence were enhanced by the addition of minerals at low pH and elevated temperature. Copyright © 2011 Elsevier B.V. All rights reserved.

Catalytic Copolymerization of Ethene and Carbon Monoxide on Nickel Complexes.

Science.gov (United States)

Domhöver, Bernd; Kläui, Wolfgang; Kremer-Aach, Andreas; Bell, Ralf; Mootz, Dietrich

1998-11-16

Can palladium be replaced by nickel? For the industrial copolymerization of carbon monoxide and ethene a palladium catalyst is used which cannot be recovered-a cheaper procedure would be desirable. The presented complex 1 is the first structurally characterized nickel compound which does not polymerize ethene but a mixture from carbon monoxide and ethene unter mild conditions to give a perfectly alternating polyketone. © 1998 WILEY-VCH Verlag GmbH, Weinheim, Fed. Rep. of Germany.

Microemulsion systems applied to breakdown petroleum emulsions

Energy Technology Data Exchange (ETDEWEB)

Neuma de Castro Dantas, Tereza; Avelino Dantas Neto, Afonso; Ferreira Moura, Everlane [Deptos de Quimica e Eng. Quimica, Universidade Federal do Rio Grande do Norte, Campus Universitario s/n, 59072.970, Natal/RN Campinas (Brazil)

2001-12-29

Microemulsion systems obtained using commercial surfactants with demulsifier and emulsion prevention properties have been employed to break down Brazilian crude water-in-oil (W/O) emulsions. These crude oils were supplied by the Brazilian oil company-PETROBRAS-and were characterized by the different Balance sheet of Sediment and Water (BSW) values of 48%, 36%, and 32%. The microemulsion systems formed in this study were composed of an aqueous phase (HCl 5.2% solution); an oil phase (toluene); a cosurfactant/surfactant (C/S) phase (isopropyl alcohol (C)/surfactants (S) with a ratio C/S of 9.0). The microemulsion efficiency to break down oil emulsions was evaluated by a direct contact method between the microemulsions and crude (W/O) emulsions. The Scheffe net statistical planning for mixtures was used to relate the component mass fractions to the relative breakdown of petroleum emulsions. The best composition of the microemulsion system for the complete breakdown of oil emulsions with high BSW values had the lowest C/S phase percentage.

Characteristics of Nano-emulsion for Cold Thermal Storage

Science.gov (United States)

Fumoto, Koji; Kawaji, Masahiro; Kawanami, Tsuyoshi

Phase change emulsion (PCE) is novel kind of heat storage and heat transfer fluids. It has characteristics as follows; greater apparent specific heat and higher heat transfer abilities in the phase change temperature range than conventional single phase heat transfer fluid. In this paper, a phase change emulsion, which has droplet diameter distribution of nanometer, were prepared. The Nano-emulsion was formed by low energy emulsification methods, as known the phase inversion temperature (PIT) method. Physical properties, such as viscosity, diameter and its distribution of emulsion were investigated. Especially, the relationships between preparation method and the concentration of surfactant have been discussed in detail. The results show that the viscosity of the Nano-emulsion is lower than the micro-emulsion, which was made by same mixing ratio of surfactant and concentration of phase change material. In addition, the Nano-emulsion clarified that stability was higher than microemulsions.

Effect of layer-by-layer coatings and localization of antioxidant on oxidative stability of a model encapsulated bioactive compound in oil-in-water emulsions.

Science.gov (United States)

Pan, Yuanjie; Nitin, N

2015-11-01

Oxidation of encapsulated bioactives in emulsions is one of the key challenges that limit shelf-life of many emulsion containing products. This study seeks to quantify the role of layer-by-layer coatings and localization of antioxidant molecules at the emulsion interface in influencing oxidation of the encapsulated bioactives. Oxidative barrier properties of the emulsions were simulated by measuring the rate of reaction of peroxyl radicals generated in the aqueous phase with the encapsulated radical sensitive dye in the lipid core of the emulsions. The results of peroxyl radical permeation were compared to the stability of encapsulated retinol (model bioactive) in emulsions. To evaluate the role of layer-by-layer coatings in influencing oxidative barrier properties, radical permeation rates and retinol stability were evaluated in emulsion formulations of SDS emulsion and SDS emulsion with one or two layers of polymers (ϵ-polylysine and dextran sulfate) coated at the interface. To localize antioxidant molecules to the interface, gallic acid (GA) was chemically conjugated with ϵ-polylysine and subsequently deposited on SDS emulsion based on electrostatic interactions. Emulsion formulations with localized GA molecules at the interface were compared with SDS emulsion with GA molecules in the bulk aqueous phase. The results of this study demonstrate the advantage of localization of antioxidant at the interface and the limited impact of short chain polymer coatings at the interface of emulsions in reducing permeation of radicals and oxidation of a model encapsulated bioactive in oil-in-water emulsions. Copyright © 2015 Elsevier B.V. All rights reserved.

Dynamic Model of Basic Oxygen Steelmaking Process Based on Multizone Reaction Kinetics: Modeling of Decarburization

Science.gov (United States)

Rout, Bapin Kumar; Brooks, Geoffrey; Akbar Rhamdhani, M.; Li, Zushu; Schrama, Frank N. H.; Overbosch, Aart

2018-03-01

In a previous study by the authors (Rout et al. in Metall Mater Trans B 49:537-557, 2018), a dynamic model for the BOF, employing the concept of multizone kinetics was developed. In the current study, the kinetics of decarburization reaction is investigated. The jet impact and slag-metal emulsion zones were identified to be primary zones for carbon oxidation. The dynamic parameters in the rate equation of decarburization such as residence time of metal drops in the emulsion, interfacial area evolution, initial size, and the effects of surface-active oxides have been included in the kinetic rate equation of the metal droplet. A modified mass-transfer coefficient based on the ideal Langmuir adsorption equilibrium has been proposed to take into account the surface blockage effects of SiO2 and P2O5 in slag on the decarburization kinetics of a metal droplet in the emulsion. Further, a size distribution function has been included in the rate equation to evaluate the effect of droplet size on reaction kinetics. The mathematical simulation indicates that decarburization of the droplet in the emulsion is a strong function of the initial size and residence time. A modified droplet generation rate proposed previously by the authors has been used to estimate the total decarburization rate by slag-metal emulsion. The model's prediction shows that about 76 pct of total carbon is removed by reactions in the emulsion, and the remaining is removed by reactions at the jet impact zone. The predicted bath carbon by the model has been found to be in good agreement with the industrially measured data.

Dynamic Model of Basic Oxygen Steelmaking Process Based on Multizone Reaction Kinetics: Modeling of Decarburization

Science.gov (United States)

Rout, Bapin Kumar; Brooks, Geoffrey; Akbar Rhamdhani, M.; Li, Zushu; Schrama, Frank N. H.; Overbosch, Aart

2018-06-01

In a previous study by the authors (Rout et al. in Metall Mater Trans B 49:537-557, 2018), a dynamic model for the BOF, employing the concept of multizone kinetics was developed. In the current study, the kinetics of decarburization reaction is investigated. The jet impact and slag-metal emulsion zones were identified to be primary zones for carbon oxidation. The dynamic parameters in the rate equation of decarburization such as residence time of metal drops in the emulsion, interfacial area evolution, initial size, and the effects of surface-active oxides have been included in the kinetic rate equation of the metal droplet. A modified mass-transfer coefficient based on the ideal Langmuir adsorption equilibrium has been proposed to take into account the surface blockage effects of SiO2 and P2O5 in slag on the decarburization kinetics of a metal droplet in the emulsion. Further, a size distribution function has been included in the rate equation to evaluate the effect of droplet size on reaction kinetics. The mathematical simulation indicates that decarburization of the droplet in the emulsion is a strong function of the initial size and residence time. A modified droplet generation rate proposed previously by the authors has been used to estimate the total decarburization rate by slag-metal emulsion. The model's prediction shows that about 76 pct of total carbon is removed by reactions in the emulsion, and the remaining is removed by reactions at the jet impact zone. The predicted bath carbon by the model has been found to be in good agreement with the industrially measured data.

Extending temporary storage capacity with emulsion breakers

International Nuclear Information System (INIS)

Buist, I.; Guarino, A.; DeVitis, D.; Nolan, K.; Lewis, A.; Smith, B.; Lane, J.

2002-01-01

The use of emulsion breakers injected into an oil spill recovery system was examined in both laboratory testing and at the OHMSETT test facility. The tests were designed to assess the injection/mixing/settling regimes needed for optimum water-removal performance from a meso-stable water-in-oil emulsion with an oil spill demulsifier. Different types of injection locations and mixing technologies were examined, including skimmer heads, cargo lines, tank inlets, as well as static in-line and mechanical technologies. During laboratory testing, water-in-oil emulsions and free water was pumped through various lengths of piping loops, an in-line mixer and 8 settling tanks. Following the injection of a demulsifier, the fluid was decanted to observe the emulsion breaking. At the OHMSETT test facility, a Desmi Terminator skimmer recovered the same emulsion from a polluted water surface. Different slick thicknesses, wave heights and recovery rates were used. A demulsifier was also injected into the recovered fluid which was allowed to separate in recovery tanks. The demulsifier efficiency was then measured. It was determined that the demulsifier significantly reduced the volume of water in the recovery tanks and the water content of the remaining emulsion. If free water content was greater than 60 per cent, then the effect of the surfactant was greatly reduced. If no free water was present, the level of turbulence was insufficient to promote emulsion breaking. More than 33 per cent free water content is needed to reduce the bulk viscosity of the fluid and to promote emulsion breaking. The degree of emulsion breaking also increased with increasing mixing energy. 10 refs., 5 tabs., 8 figs

Deep eutectic solvents as performance additives in biphasic reactions

NARCIS (Netherlands)

Lan, Dongming; Wang, Xuping; Zhou, Pengfei; Hollmann, F.; Wang, Yonghua

2017-01-01

Deep eutectic solvents act as surfactants in biphasic (hydrophobic/aqueous) reaction mixtures enabling higher interfacial surface areas at lower mechanical stress as compared to simple emulsions. Exploiting this effect the rate of a chemoenzymatic epoxidation reaction was increased more than

Radiation induced graft copolymerization for preparation of cation exchange membranes: a review

International Nuclear Information System (INIS)

Mohamed Mahmoud Nasef; Hamdani Saidi; Hussin Mohd Nor

1999-01-01

Cation exchange membranes are regarded as the ideal solid polymer electrolyte materials for the development of various electrochemical energy conversion applications where significant improvements in the current density are required. Such membranes require special polymers and preparation techniques to maintain high chemical , mechanical and thermal stability in addition to high ionic conductivity and low resistance. A lot of different techniques have been proposed in the past to prepare such membranes. Radiation-induced graft copolymerization provides an attractive ft method for modification of chemical and physical properties of polymeric materials and is of particular interest in achieving specially desired cation exchange membranes as well as excellent membrane properties. This is due to the ability to control the membrane compositions as well as properties by proper selection of grafting conditions. Therefore numerous parameters have to be investigated to properly select the right polymeric materials, radiation grafting technique and the grafting conditions to be employed. In this paper a state-of-the-art of radiation-induced graft copolymerization for preparation of cation exchange membranes and their applications are briefly reviewed. (Author)

Green tea extract impairs meat emulsion properties by disturbing protein disulfide cross-linking.

Science.gov (United States)

Jongberg, Sisse; Terkelsen, Linda de S; Miklos, Rikke; Lund, Marianne N

2015-02-01

The dose-dependent effects of green tea extract (100, 500, or 1500ppm) on the textural and oxidative stability of meat emulsions were investigated, and compared to a control meat emulsion without extract. All levels of green tea extract inhibited formation of TBARS as a measure for lipid oxidation. Overall protein thiol oxidation and myosin heavy chain (MHC) cross-linking were inhibited by 100ppm green tea extract without jeopardizing the textural stability, while increasing concentrations of extract resulted in reduced thiol concentration and elevated levels of non-reducible protein modifications. Addition of 1500ppm green tea extract was found to modify MHC as evaluated by SDS-PAGE combining both protein staining and specific thiol staining, indicating that protein modifications generated through reactions of green tea phenolic compounds with protein thiols, disrupted the meat emulsion properties leading to reduced water holding capacity and textural stability. Hence, a low dose of green tea extract preserves both the textural and the oxidative stability of the meat proteins. Copyright © 2014 Elsevier Ltd. All rights reserved.

Cleaning fluid emulsions

Energy Technology Data Exchange (ETDEWEB)

Prikryl, J; Kotyza, R; Krulikovsky, J; Mjartan, V; Valisova, I

1981-09-15

Composition of cleaning fluid emulsion are presented for drilling small diameter wells in clay soils, at high drill bit rotation velocity. The emulsions have lubricating properties and the abilty to improve stability of the drilled soil. The given fluids have a high fatty acid content with 12-24 carbon atoms in a single molecule, with a predominance of resinous acids 1-5% in mass, and having been emulsified in water or clay suspension without additives, or in a clay suspension with high-molecular polymer additives (glycobate cellulose compounds and/or polysaccharides, and/or their derivatives) in an amount of 0.1-3% per mass; thinning agents - huminite or lignite compounds in the amount of 0.01 to 0.5% in mass; weighting material - barite or lime 0.01 to 50% per mass; medium stabilizers - organic poly-electrolyte with polyacrylate in the amount of 0.05 to 2% in mass, or alkaline chloride/alkaline-ground metals 1-10% per mass. A cleaning emulsion fluid was prepared in the laboratory according to the given method. Add 3 kg tall oil to a solution of 1 kg K/sub 2/CO/sub 3/ per 100 l of water. Dynamic viscosity was equal to 1.4 x 10-/sup 3/ Pa/s. When drilling in compacted clay soils, when the emulsions require improved stability, it is necessary to add the maximum amount of tall oil whose molecules are absorbed by the clay soil and increase its durability.

Photocrosslinkable Star Polymers via RAFT-Copolymerizations with N-Ethylacrylate-3,4-dimethylmaleimide

Directory of Open Access Journals (Sweden)

Philipp Vana

2013-06-01

Full Text Available This paper describes the Z-RAFT-star copolymerization of n-butyl acrylate (BA and N-isopropyl acrylamide (NIPAm, respectively, with N-ethylacrylate-3,4-dimethylmaleimide (1.1, a monomer carrying a UV-reactive unit that undergoes photocrosslinking. Addition of 1.1 slows down the polymerization rate both for BA and for NIPAm polymerization. Double star formation due to radical attack to the 3,4-dimethylmaleimide moiety was found in the case of BA. Dead polymer formation, presumably due to aminolysis as side-reaction, was pronounced in the NIPAm system. These two effects broadened the molar mass distributions, but did not impede the formation of functional star polymers. The composition of the copolymers as well as the reactivity ratios for the applied comonomers were determined via NMR spectroscopy (BA-co-1.1 r1.1 = 2.24 rBA = 0.95; NIPAm-co-1.1 r1.1 = 0.96 rNIPAm = 0.05. In both cases, the comonomer is consumed preferably in the beginning of the polymerization, thus forming gradient copolymer stars with the UV-reactive units being located in the outer sphere.

Laboratory effectiveness testing of water-in-oil emulsion breakers

International Nuclear Information System (INIS)

Fingas, M.F.; Fieldhouse, B.; Bier, I.; Conrod, D.; Tennyson, E.

1995-01-01

The physics and chemistry of water-in-oil emulsions dominate the development of effectiveness tests. Emulsions are variable in stability--this variability is largely dependent on oil type and degree of weathering. These factors complicate the development of a test. Emulsions which have low stability will apparently break easily with chemical emulsion breakers. Broken emulsions will form a foam-like material, called rag, which retains water which is not part of the stable emulsions. Analytical methods used to determine the final stability of the broken or unbroken emulsion were evaluated. Measurements of water content and viscosity measurements show correlation to emulsion stability. Viscosity provides a more reliable measure of emulsion stability but water content measurements are more convenient and are largely used in this study. Twelve tests were developed in the past. Two testing methods have been developed to a usable stage. These tests are described and data using them provided. The effects of mixing time, agent amount, settling time and mixing energy on effectiveness results are presented

Boundary lubrication of stainless steel and CoCrMo alloy based on phosphorous and boron compounds in oil-in-water emulsion

International Nuclear Information System (INIS)

Yan, Jincan; Zeng, Xiangqiong; Ren, Tianhui; Heide, Emile van der

2014-01-01

Highlights: • The boundary lubrication behaviour of three O/W emulsions was investigated. • The interactions between O/W emulsions and CoCrMo surfaces were studied. • Three different additives containing P and B were added in the emulsions. • The tribologcial performance of oil lubricant and emulsion was compared. • The friction profile of emulsion shows three stages due to spreading and plate-out. - Abstract: Emulsion lubrication is widely used in metal forming operations and has potential applications in the biomedical field, yet the emulsion lubrication mechanism is not well understood. This work explores the possibilities of three different oil-in-water (O/W) emulsions containing dibutyl octadecylphosphoramidate (DBOP), 6-octadecyl-1,3,6,2-dioxazaborocan-2-ol calcium salt (ODOC) and 2-(4-dodecylphenoxy)-6-octadecyl-1,3,6,2-dioxazaborocane (DOB) to generate boundary films on stainless steel AISI 316 and CoCrMo alloy surfaces. Experimental results show lower friction values for the emulsions in combination with CoCrMo compared to AISI 316. The different performance of the additives is related to the composition of the adsorption and reaction film on the interacting surfaces, which was shown to be dependent on the active elements and molecular structure of the additives. The friction profile of the emulsions indicates that the emulsion appears to be broken during the rubbing process, then the additives adsorb onto the metal surface to form protecting boundary layers. The XPS analysis shows that for boundary lubrication conditions, the additive molecules in the emulsion first adsorb on the metal surface after the droplet is broken, and then decompose and react with the metal surface during the rubbing process to form stable lubricating films on the rubbed surfaces

Boundary lubrication of stainless steel and CoCrMo alloy based on phosphorous and boron compounds in oil-in-water emulsion

Energy Technology Data Exchange (ETDEWEB)

Yan, Jincan [Laboratory for Surface Technology and Tribology, University of Twente (Netherlands); School of Chemistry and Chemical Engineering, Key Laboratory for Thin Film and Microfabrication, Shanghai Jiao Tong University (China); Zeng, Xiangqiong, E-mail: X.Zeng@utwente.nl [Laboratory for Surface Technology and Tribology, University of Twente (Netherlands); School of Chemistry and Chemical Engineering, Key Laboratory for Thin Film and Microfabrication, Shanghai Jiao Tong University (China); Ren, Tianhui [School of Chemistry and Chemical Engineering, Key Laboratory for Thin Film and Microfabrication, Shanghai Jiao Tong University (China); Heide, Emile van der [Laboratory for Surface Technology and Tribology, University of Twente (Netherlands); TNO (Netherlands)

2014-10-01

Highlights: • The boundary lubrication behaviour of three O/W emulsions was investigated. • The interactions between O/W emulsions and CoCrMo surfaces were studied. • Three different additives containing P and B were added in the emulsions. • The tribologcial performance of oil lubricant and emulsion was compared. • The friction profile of emulsion shows three stages due to spreading and plate-out. - Abstract: Emulsion lubrication is widely used in metal forming operations and has potential applications in the biomedical field, yet the emulsion lubrication mechanism is not well understood. This work explores the possibilities of three different oil-in-water (O/W) emulsions containing dibutyl octadecylphosphoramidate (DBOP), 6-octadecyl-1,3,6,2-dioxazaborocan-2-ol calcium salt (ODOC) and 2-(4-dodecylphenoxy)-6-octadecyl-1,3,6,2-dioxazaborocane (DOB) to generate boundary films on stainless steel AISI 316 and CoCrMo alloy surfaces. Experimental results show lower friction values for the emulsions in combination with CoCrMo compared to AISI 316. The different performance of the additives is related to the composition of the adsorption and reaction film on the interacting surfaces, which was shown to be dependent on the active elements and molecular structure of the additives. The friction profile of the emulsions indicates that the emulsion appears to be broken during the rubbing process, then the additives adsorb onto the metal surface to form protecting boundary layers. The XPS analysis shows that for boundary lubrication conditions, the additive molecules in the emulsion first adsorb on the metal surface after the droplet is broken, and then decompose and react with the metal surface during the rubbing process to form stable lubricating films on the rubbed surfaces.

Mixing Time, Inversion and Multiple Emulsion Formation in a Limonene and Water Pickering Emulsion

Directory of Open Access Journals (Sweden)

Laura Sawiak

2018-05-01

Full Text Available It has previously been demonstrated that particle-stabilized emulsions comprised of limonene, water and fumed silica particles exhibit complex emulsification behavior as a function of composition and the duration of the emulsification step. Most notably the system can invert from being oil-continuous to being water-continuous under prolonged mixing. Here we investigate this phenomenon experimentally for the regime where water is the majority liquid. We prepare samples using a range of different emulsification times and we examine the final properties in bulk and via confocal microscopy. We use the images to quantitatively track the sizes of droplets and clusters of particles. We find that a dense emulsion of water droplets forms initially which is transformed, in time, into a water-in-oil-in-water multiple emulsion with concomitant changes in droplet and cluster sizes. In parallel we carry out rheological studies of water-in-limonene emulsions using different concentrations of fumed silica particles. We unite our observations to propose a mechanism for inversion based on the changes in flow properties and the availability of particles during emulsification.

Microfluidic methods to study emulsion formation

OpenAIRE

Muijlwijk, Kelly

2017-01-01

Emulsions are dispersions of one liquid in another that are commonly used in various products, and methods such as high-pressure homogenisers and colloid mills are used to form emulsions. The size and size distribution of emulsion droplets are important for the final product properties and thus need to be controlled. Rapid coalescence of droplets during emulsification increases droplet size and widens the size distribution, and therefore needs to be prevented. To increase stability of emulsio...

RAFT Polymerization of Styrene and Maleimide in the Presence of Fluoroalcohol: Hydrogen Bonding Effects with Classical Alternating Copolymerization as Reference

Directory of Open Access Journals (Sweden)

Fangjun Yao

2017-03-01

Full Text Available The impacts of hydrogen bonding on polymerization behavior has been of interest for a long time; however, universality and in-depth understanding are still lacking. For the first time, the effect of hydrogen bonding on the classical alternating-type copolymerization of styrene and maleimide was explored. N-phenylmaleimide (N-PMI/styrene was chosen as a model monomer pair in the presence of hydrogen bonding donor solvent 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP, which interacted with N-PMI via hydrogen bonding. Reversible addition-fragmentation chain transfer polymerization (RAFT technique was used to guarantee the “living” polymerization and thus the homogeneity of chain compositions. In comparison with the polymerization in nonhydrogen bonding donor solvent (toluene, the copolymerization in HFIP exhibited a high rate and a slight deviation from alternating copolymerization tendency. The reactivity ratios of N-PMI and St were revealed to be 0.078 and 0.068, respectively, while the reactivity ratios in toluene were 0.026 and 0.050. These interesting results were reasonably explained by using computer simulations, wherein the steric repulsion and electron induction by the hydrogen bonding between HFIP and NPMI were revealed. This work first elucidated the hydrogen bonding interaction in the classical alternating-type copolymerization, which will enrich the research on hydrogen bonding-induced polymerizations.

Graft copolymerization of N-vinyl-2-pyrrolidone onto pre-irradiated poly(vinylidene fluoride) powder

International Nuclear Information System (INIS)

Xu Chenqi; Huang Wei; Zhou Yongfeng; Yan Deyue; Chen Shutao; Huang Hua

2012-01-01

Graft copolymerization of N-vinyl-2-pyrrolidone (NVP) onto 60 Co γ-ray pre-irradiated poly (vinylidene fluoride) (PVDF) powder was investigated to find out the relationship between the degree of grafting (DG) and various factors, including monomer concentration, irradiation dose, reaction time, catalyst and so on. The DG can be calculated by comparing the amount of nitrogen element in the resulting copolymer (PVDF-g-PVP) powder with that in PVP on the basis of element analysis. The presence of PVP in the resulting PVDF powder was confirmed by the comparative studies of pristine PVDF and grafted PVDF powder through Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR), X-ray photoelectron spectroscopy (XPS), thermo gravimetric analyzer (TGA) and differential scanning calorimetry (DSC), respectively. When the reaction was performed at the monomer concentration of 20% (vol.) and the absorbed dose of 40 kGy for 3 h in water, the max. DG of 17.7% was obtained. - Highlights: ► We modify pristine PVDF powders with NVP by the pre-irradiated graft polymerization. ► The various factors influencing the degree of grafting are investigated in detail. ► The optimal condition of graft polymerization is obtained. ► The polymerization is processed at 20% (vol.) of NVP and 40kGy for 3 hours in water. ► The maximum degree of grafting is 17.7 % at such a condition.

Effect of acid additives on graft copolymerization and water absorption of graft copolymers of cassava starch and acrylamide/acrylic acid

International Nuclear Information System (INIS)

Kiatkamjornwong, Suda; Mongkolsawat, Kanlaya; Sonsuk, Manit

2003-01-01

Gelatinized cassava starch was radiation graft copolymerized with acrylamide or acrylic acid in the presence of sulfuric acid, nitric acid or maleic acid at a specific dose rate to a fixed total dose. Homopolymer or free copolymer was extracted by water to obtain the pure graft copolymer, which was subsequently saponified with 5% potassium hydroxide solution at room temperature for 90 min. The saponified graft copolymer was investigated for the effect of acid additives and water absorption. The addition of 2% maleic acid into the grafting reaction containing acrylamide-to-starch ratio of 2.5:1 can produce the superabsorbent copolymer having water absorption as high as 2,256 ± 25 g g -1 . The effect of acid additive was explained. (author)

Food emulsions as delivery systems for flavor compounds: A review.

Science.gov (United States)

Mao, Like; Roos, Yrjö H; Biliaderis, Costas G; Miao, Song

2017-10-13

Food flavor is an important attribute of quality food, and it largely determines consumer food preference. Many food products exist as emulsions or experience emulsification during processing, and therefore, a good understanding of flavor release from emulsions is essential to design food with desirable flavor characteristics. Emulsions are biphasic systems, where flavor compounds are partitioning into different phases, and the releases can be modulated through different ways. Emulsion ingredients, such as oils, emulsifiers, thickening agents, can interact with flavor compounds, thus modifying the thermodynamic behavior of flavor compounds. Emulsion structures, including droplet size and size distribution, viscosity, interface thickness, etc., can influence flavor component partition and their diffusion in the emulsions, resulting in different release kinetics. When emulsions are consumed in the mouth, both emulsion ingredients and structures undergo significant changes, resulting in different flavor perception. Special design of emulsion structures in the water phase, oil phase, and interface provides emulsions with great potential as delivery systems to control flavor release in wider applications. This review provides an overview of the current understanding of flavor release from emulsions, and how emulsions can behave as delivery systems for flavor compounds to better design novel food products with enhanced sensorial and nutritional attributes.

Radiation initiated copolymerization of allyl alcohol with acrylonitrile

International Nuclear Information System (INIS)

Solpan, Dilek; Guven, Olgun

1996-01-01

Copolymerization of allyl alcohol (AA) with acrylonitrile (AN) initiated by γ-rays has been investigated to determine the respective reactivity ratios. Three different experimental techniques, namely Fourier Transform Infrared (FTIR), Ultraviolet (UV/vis) and elemental analysis (EA) have been used for the determination of copolymer compositions. Fineman-Ross (FR), Kelen-Tudos (KT), Non-Linear Least Square (NLLS) Analysis and Q-e methods have been applied to the three sets of experimental data. It has been concluded that data obtained from elemental analysis as applied to the Non-Linear Least Square approach gave the most reliable reactivity ratios as 2.09 and 0.40 for acrylonitrile and allyl alcohol, respectively. (Author)

Mathematical Approach in Rheological Characterizing of Asphalt Emulsion Residues

Directory of Open Access Journals (Sweden)

Seong Hwan Cho

2015-01-01

Full Text Available Three different emulsion residues, such as SS1HP, HFE90, and SS-1VH (trackless, and a base asphalt binder (PG 64-22 are compared to characterize rheological properties by using DSR test. In order to capture the emulsion properties, different frequencies (from 1 to 100 rad/sec at a 10% constant shear rate and temperatures (from −45°C to 75°C with 15°C increments were applied. Then, a master curve for shear modulus was plotted for each emulsion. The transition of the HFE90 emulsion from viscous to elastic behavior occurs at lower temperatures, compared to the other materials. This emulsion is known for performing in a wider temperature range as shown in the results. The trackless emulsion presents an elastic behavior at intermediate temperatures. This product is known as having very fast setting and high resistance to shear stresses. The trackless emulsion presents the highest viscous and elastic modulus, followed by the PG 64-22 binder, SS1HP, and HFE90 emulsion. Shear strength test results show a behavior between trackless emulsion and SS1HP similar to the frequency sweep test results performed by DSR.

Cold in-place recycling using solventless emulsion - phase IV (emulsion qualification and long-term field performance).

Science.gov (United States)

2016-05-01

This report looks into how a successful Cold In-Place solventless emulsion behaves and how the emulsion : break test developed in Phase III of this project demonstrates that behavior. Modifications to the test have been : made to improve the consiste...

Abaca/polyester nonwoven fabric functionalization for metal ion adsorbent synthesis via electron beam-induced emulsion grafting

International Nuclear Information System (INIS)

Madrid, Jordan F.; Ueki, Yuji; Seko, Noriaki

2013-01-01

A metal ion adsorbent was developed from a nonwoven fabric trunk material composed of both natural and synthetic polymers. A pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca/polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on absorbed dose, reaction time and monomer concentration were evaluated. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3 h reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 °C, a grafted APNWF with a Dg greater than 150% was obtained. The GMA-grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 °C to introduce amine functional groups. After a 3 h reaction with 50% EDA, an amine group density of 2.7 mmole/gram adsorbent was achieved based from elemental analysis. Batch adsorption experiments were performed using Cu 2+ and Ni 2+ ions in aqueous solutions with initial pH of 5 at 30 °C. Results show that the adsorption capacity of the grafted adsorbent for Cu 2+ is four times higher than Ni 2+ ions. - Highlights: • An amine type adsorbent from abaca/polyester nonwoven fabric was synthesized. • Pre-irradiation method was used in grafting glycidyl methacrylate on nonwoven fabric. • Radiation-induced grafting was performed with monomer in emulsion state. • The calculated adsorption capacity for Cu 2+ is four times higher than Ni 2+ ions. • Grafted adsorbent can remove Cu 2+ faster than a chemically similar commercial resin

Storage stability of marine phospholipids emulsions

DEFF Research Database (Denmark)

Lu, Henna Fung Sieng; Nielsen, Nina Skall; Baron, Caroline Pascale

Marine phospholipids (MPL) are believed to provide more advantages than fish oil from the same source. They are considered to have a better bioavailability, a better resistance towards oxidation and a higher content of polyunsaturated fatty acids such as eicosapentaenoic (EPA) and docosahexaenoic...... acids (DHA) than oily triglycerides (fish oil). Therefore, the objective of this study is to explore the feasibility of using marine phospholipids emulsions as delivery system through investigation of the physical, oxidative and hydrolytic stability of MPL emulsions with or without addition of fish oil....... The effect of initial Peroxide Value, total lipids, phospholipids and antioxidants content on stability of MPL emulsions were studied. The physical stability was investigated through measurement of particle size distribution and creaming stability, which involve measurement of changes (%) in emulsion volume...

Reactivity of vinyl ethers and vinyl ribosides in UV-initiated free radical copolymerization with acceptor monomers.

Science.gov (United States)

Pichavant, Loic; Guillermain, Céline; Coqueret, Xavier

2010-09-13

The reactivity of various vinyl ethers and vinyloxy derivatives of ribose in the presence of diethyl fumarate or diethyl maleate was investigated for evaluating the potential of donor-acceptor-type copolymerization applied to unsaturated monomers derived from renewable feedstock. The photochemically induced polymerization of model monomer blends in the bulk state was monitored by infrared spectroscopy. The method allowed us to examine the influence of monomer pair structure on the kinetic profiles. The simultaneous consumption of both monomers was observed, supporting an alternating copolymerization mechanism. A lower reactivity of the blends containing maleates compared with fumarates was confirmed. The obtained kinetic data revealed a general correlation between the initial polymerization rate and the Hansen parameter δ(H) associated with the H-bonding aptitude of the donor monomer.

Optimizing the bulk copolymerization of D,L-lactide and glycolide by response surface methodology

Directory of Open Access Journals (Sweden)

J. F. Rodriguez

2013-11-01

Full Text Available Poly(D,L-lactide-co-glycolide, PLGA, is a biodegradable polyester with high interest in medical industry, especially when zinc (II 2-ethylhexanoate (ZnOct2 is used as catalyst substitute in polymerization processes as a substitute of the toxic tin (II 2-ethylhexanoate (SnOct2 together an initiator such as methanol to improve the reaction rate. This article shows the optimization of the bulk copolymerization method by using a factorial design approach on three experimental parameters: temperature (T, molar ratio monomers/catalyst (MC ratio and molar ratio initiator/catalyst (IC ratio. Their influence on mass conversion (X and number-average molecular weight (Mn was also discussed. Also it provides a useful tool to select in a fast way the proper experimental conditions for the obtaining of this polymer as a previous stage in the synthesis and impregnation of biodegradable scaffolds. This analysis revealed that the most relevant variable in the process is the temperature, being desirable to use the high value (160ºC in order to obtain high values of conversion and molecular weight.

Emulsifier development for high-concentrated reverse emulsions

Directory of Open Access Journals (Sweden)

I.L. Kovalenko

2016-05-01

Full Text Available The reverse emulsions have found broad application in ore mining industry as matrixes of emulsion explosive substances and boring washing waters. The defining characteristic of reverse emulsions of industrial explosive substances is the high stability and immunity to crystallization. Aim: The aim of this work is to assess the mechanism of emulsifiers effect like SMO and some PIBSA-derivatives, that are most abundantly used in world practice, and also to develop an effective domestic emulsifier of reverse emulsions. Materials and methods: Using the semi-dynamic method with use of the reverse stalagmometer it was determined the decreasing in interfacial tension on “water / diesel fuel” border in the presence of 0.5 wt % sorbitan monooleate of various producers. Emulsions with use of the chosen emulsifiers using the dynamic mixer on the basis of monosolution of ammonium nitrate and diesel fuel have been produced. The emulsions have the following composition, wt %: ammonium nitrate – 76.8; water – 15.6; diesel fuel – 6.0; emulsifier – 1.6. Results: By the researches results of the interfacial tension “surfactant water / solution in diesel fuel”, the stability of emulsions using monosolution of ammonium nitrate and the IR spectrums of SMO of various producers it is established that presence in product of impurity of oleic acid, di- and trioleates leads to decreasing in interphase activity, increasing of emulsifier oil solubility and decreasing the resistance of emulsions to crystallization. On the basis of the spectral data analysis it is suggested about possibility of specific interaction on the mechanism of “spectral resonance” between emulsifiers of the PIBSA-MEA, LZX type and crystals nucleus of NH4NO3 ammonium nitrate in dispersed phase of emulsion. Amidation of vegetable oils by monoethanol amine is implemented at the reduced temperatures (90…100 °C. It was proved the availability mainly of fatty acids amides in product

Abaca/polyester nonwoven fabric functionalization for metal ion adsorbent synthesis via electron beam-induced emulsion grafting

Science.gov (United States)

Madrid, Jordan F.; Ueki, Yuji; Seko, Noriaki

2013-09-01

A metal ion adsorbent was developed from a nonwoven fabric trunk material composed of both natural and synthetic polymers. A pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca/polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on absorbed dose, reaction time and monomer concentration were evaluated. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3 h reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 °C, a grafted APNWF with a Dg greater than 150% was obtained. The GMA-grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 °C to introduce amine functional groups. After a 3 h reaction with 50% EDA, an amine group density of 2.7 mmole/gram adsorbent was achieved based from elemental analysis. Batch adsorption experiments were performed using Cu2+ and Ni2+ ions in aqueous solutions with initial pH of 5 at 30 °C. Results show that the adsorption capacity of the grafted adsorbent for Cu2+ is four times higher than Ni2+ ions.

Experimental investigation of a new iodinated lipid emulsion for computed tomography of the liver

International Nuclear Information System (INIS)

Ivancev, K.; Lunderquist, A.; McCuskey, R.; McCuskey, P.; Wretlind, A.; Arizona Univ., Tucson, AZ; Veterans Administration Medical Center, Tucson, AZ

1989-01-01

We have tested a new iodinated lipid emulsion, Intraiodol. The size and surface properties of the particles of this emulsion are similar to those of Intralipid which in turn closely resemble the naturally occurring chylomicrons. Using computed tomography (CT) of the rabbit liver as well as vital microscopy and electron microscopy of the rat liver we found that Intraiodol has low efficiency as a liver-specific contrast medium because its particles are predominantly taken up by the hepatocytes and to a less extent by the Kupffer cells, as is Intralipid. The low efficiency of Intraiodol could be fully compensated by an increase in dosage without any significant effect on sinusoidal blood flow. This in turn suggests that the likelihood of release of toxic mediators (and thereby related adverse reactions from activated macrophages) is reduced. We believe that this new way of delivering iodinated lipid particles to the liver represents an important advance in the search for a non-toxic lipid emulsion for CT of the liver. (orig./MG)

Chemistry and technology of emulsion polymerisation

NARCIS (Netherlands)

Herk, van A.M.

2005-01-01

Emulsion polymerisation produces high value polymers in a low cost, environmentally friendly process. The drive to develop environmentally benign production methods for polymers has resulted in widespread development and implementation of the emulsion polymerisation technique. In addition, when

Pre-irradiation induced emulsion graft polymerization of acrylonitrile onto polyethylene nonwoven fabric

International Nuclear Information System (INIS)

Liu Hanzhou; Yu Ming; Deng Bo; Li Linfan; Jiang Haiqing; Li Jingye

2012-01-01

Acrylonitrile has been widely used in the modification of polymers by graft polymerization. In the present work, pre-irradiation induced emulsion graft polymerization method is used to introduce acrylonitrile onto PE nonwoven fabric instead of the traditional reaction in organic solvents system. The degree of grafting (DG) is measured by gravimetric method and the kinetics of the graft polymerization is studied. The existence of the graft chains is proven by Fourier transform infrared spectroscopy (FT-IR) analysis. Thermal stability of the grafted polymer is measured by Thermogravimetric analysis (TGA). - Highlights: → Acrylonitrile is grafted onto pre-irradiated polyethylene (PE) nonwoven fabrics. → Emulsion system is applied, for the graft polymerization avoids organic solvent. → Kinetic of the pre-irradiation induced graft polymerization is studied. → Optimal condition is determined at the temperature below the b.p. of acrylonitrile.

Egg white powder-stabilised multiple (water-in-olive oil-in-water) emulsions as beef fat replacers in model system meat emulsions.

Science.gov (United States)

Öztürk, Burcu; Urgu, Müge; Serdaroğlu, Meltem

2017-05-01

Today, multiple emulsions are believed to have a considerable application potential in food industry. We aimed to investigate physical, chemical and textural quality characteristics of model system meat emulsions (MSME) in which beef fat (C) was totally replaced by 10% (E-10), 20% (E-20) or 30% (E-30) multiple emulsions (W 1 /O/W 2 ) prepared with olive oil and egg white powder (EWP). Incorporation of W 1 /O/W 2 emulsion resulted in reduced fat (from 11.54% to 4.01%), increased protein content (from 13.66% to 14.74%), and modified fatty acid composition, significantly increasing mono- and polyunsaturated fatty acid content and decreasing saturated fatty acid content. E-20 and E-30 samples had lower jelly and fat separation (5.77% and 5.25%) compared to C and E-10 (9.67% and 8.55%). W 1 /O/W 2 emulsion treatments had higher water-holding capacity (93.96-94.35%) than C samples (91.84%), and also showed the desired storage stability over time. Emulsion stability results showed that E-20 and E-30 samples had lower total expressible fluid (14.05% and 14.53%) and lower total expressible fat (5.06% and 5.33%) compared to C samples (19.13% and 6.09%). Increased concentrations of W 1 /O/W 2 emulsions led to alterations in colour and texture parameters. TBA values of samples were lower in W 1 /O/W 2 emulsion treatments than control treatment during 60 days of storage. Our results indicated that multiple emulsions prepared with olive oil and EWP had promising impacts on reducing fat, modifying the lipid composition and developing both technologically and oxidatively stable meat systems. These are the first findings concerning beef matrix fat replacement with multiple emulsions stabilised by EWP. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Formation of network during radiation three-dimentional copolymerization of α, ω-dibutyl-bis-maleatetriethylene glycol with styrene

International Nuclear Information System (INIS)

Bol'bit, N.M.; Bol'shakova, T.A.; Fajzi, N.Kh.; Chikin, Yu.A.

1983-01-01

The radiation-induced copolymerization of α,ω-dibutyl-bis-maleatetriethylene glycol (dimaleate) with styrene in bulk has been studied for the ratio of initial molar concentrations of styrene to dimaleate being equal to 1.9. Initiation has been carried out using 60 Co gamma radiation with intensity 650 rad/s. Radiation doses are 3.5-16 Mrad. Up to approximately 18% conversion only soluble copolymer is formed. Per approximately 3.5 units of styrene in this copolymer 1 unit of dimaleate with one unreacted double bond is detected. Then in the narrow range of conversion the transformation of the main part soluble copolymer into macrogel proceeds. This fact is apparently the result of the change of physical state of the system alike the microphase separation resulting in essential increase of the probability of reaction between propagating radicals of neigh-- boring molecules and maleate bonds

Graft copolymerization of N-maleoyl-N-phthaloyl-chitosan (MAPHCS) and acrylic acid via γ-ray irradiation

International Nuclear Information System (INIS)

Mu Qing; Fang Yue'e

2006-01-01

Chitosan is a well-known abundant natural polymer with good biodegradability, biocompatibility and bioactivity. But its insolubility in common organic solvents of chitosan have hindered its utilization and basic research. N-maleoyl-N-phthaloyl-chitosan (MAPHCS), soluble in DMF or DMSO, was synthesized and characterized by Fourier transform infrared spectra analysis (FT-IR) and 1 H-NMR. The graft copolymerization of acrylic acid onto chitosan was carried out with N-maleoyl-N-phthaloyl-chitosan as intermediate in homogeneous system and initiated by γ-irradiation. The double bond of MAPHCS may be the grafting site because the grafting field was much higher than that of the graft copolymerization of acrylic acid and phthaloylchitosan via γ-ray irradiation. The chemical structure of the graft copolymer was characterized by FT-IR and 1 H-NMR. As indicated in FTIR spectra, the evidence of the stronger absorbance at 2800-3000 cm -1 for C-H and at 1720 cm -1 for carboxyl group implied significantly the successful introduction of the poly (acrylic acid) on the chitosan chain. Differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) were also used to characterize the copolymer. Effects of synthesis variables on the graft copolymerization were studied in light of the grafting percentage. The grafting percentage increased with the dose at lower doses, and then decreased. The maximum grafting percentage was up to 132%. (authors)

Long-term characteristics of nuclear emulsion

International Nuclear Information System (INIS)

Naganawa, N; Kuwabara, K

2010-01-01

Long-term characteristics of the nuclear emulsion so called 'OPERA film' used in the neutrino oscillation experiment, OPERA, has been studied for 8 years since its production or refreshing after it. In the results, it turned out to be excellent in sensitivity, amount of random noise, and refreshing characteristics. The retention capacity of latent image of tracks was also studied. The result will open the way to the recycling of 7,000,000 emulsion films which will remain not developed after 5 years of OPERA's run, and other long-term experiments with emulsion.

Long-term characteristics of nuclear emulsion

Science.gov (United States)

Naganawa, N.; Kuwabara, K.

2010-02-01

Long-term characteristics of the nuclear emulsion so called ``OPERA film'' used in the neutrino oscillation experiment, OPERA, has been studied for 8 years since its production or refreshing after it. In the results, it turned out to be excellent in sensitivity, amount of random noise, and refreshing characteristics. The retention capacity of latent image of tracks was also studied. The result will open the way to the recycling of 7,000,000 emulsion films which will remain not developed after 5 years of OPERA's run, and other long-term experiments with emulsion.

Copolymerization of Styrene and Methacrylates in the presence of Catalytic Chain Transfer Agents (Cacti's)

International Nuclear Information System (INIS)

Hussain, M.Sakhawat; Khan, M.A.; Ahmad, Shafique

2005-01-01

The present paper focuses on the use of a Co (II) complex, [Co(afdo-H)] as a catalytic chain transfer agent (CCTA) for controlling molecular weight in copolymerization of styrene (STY) with butyl methacrylate (BMA) and methylmethacrylate (MMA). The catalyst is structurally similar to [co(dmg-H) (BF)] patented by Du Pont as a CCTA. Average catalytic chain transfer constant, C8 of [co(afdo-H) (BF)] for coplymerization of STY with BMA and MMA determined from Maya plot, was found to be in the range of 10-10.This value is lower than the value reported for the [Co(dmg-H)(BF)). In the case of STY-BMA or STY-MMA copolymerization, a considerable reduction in the viscosity average molecular weights (Mv) was observed in the copolymers. The average molecular weight of poly (MMA-BMA) was reduced by a factor of ten compared to the reduction in poly (STY-MMA) and poly (STY-BMA) for the same concentration of the CCTA. (author)

Pulse seed germination improves antioxidative activity of phenolic compounds in stripped soybean oil-in-water emulsions.

Science.gov (United States)

Xu, Minwei; Jin, Zhao; Peckrul, Allen; Chen, Bingcan

2018-06-01

The purpose of this study was to investigate antioxidative activity of phenolic compounds extracted from germinated pulse seed including chickpeas, lentils and yellow peas. Phenolic compounds were extracted at different germination time and total phenolic content was examined by Folin Ciocalteu's reaction. Antioxidative activity of extracts was characterized by in vitro assay including 2, 2-diphenyl-1-picrylhydrazyl radical scavenging capacity (DPPH), oxygen radical absorbance capacity (ORAC), iron-binding assay, and in stripped soybean oil-in-water emulsions. The results suggested that germination time is critical for phenolic compounds production. The form variation of phenolic compounds influenced the antioxidative activity of phenolic compounds both in vitro assay and in emulsion systems. Soluble bound phenolic compounds showed higher antioxidative ability in emulsion system with the order of chickpea > yellow pea > lentil. On the basis of these results, soluble bound phenolic compounds may be considered as a promising natural antioxidant to prevent lipid oxidation in foods. Copyright © 2018 Elsevier Ltd. All rights reserved.

Nuclear emulsion and high-energy physics

International Nuclear Information System (INIS)

Sun Hancheng; Zhang Donghai

2008-01-01

The history of the development of nuclear emulsion and its applications in high-energy physics, from the discovery of pion to the discovery of tau neutrino, are briefly reviewed in this paper. A new stage of development of nuclear-emulsion technique is discussed

Charm studies in emulsion

CERN Document Server

Kalinin, Sergey

Neutrino-nucleon scattering is an effective way to investigate the inner structure of the nucleon, to extract the Standard Model parameters and to explore heavy quarks production dynamics. In the last decades, several experiments have been constructed to study weak interactions of neutrinos with nucleons. One of them was CERN-WA95 experiment operated by the CHORUS collaboration. It is based on a hybrid detector with nuclear emulsion as a target followed by electronic devices. Nuclear emulsion provides three dimensional spatial information with an outstanding resolution of the order of one micron. Therefore, it is ideal to detect short-lived particles. A special technique has been developed to reconstruct events in the emulsion which allows to perform a detailed investigation of events such as charmed hadrons production by neutrinos. As a result, the backround in the selected charm sample is up to six times lower compared to similar experiments. Such a method also permits to make direct measurements of some qu...

Innovative precipitation in emulsion process: toward a non-nuclear industrial application

International Nuclear Information System (INIS)

Ollivier, M.; Borda, G.; Charton, S.; Flouret, J.

2016-01-01

A precipitation in emulsion process has been proposed by Borda et al. in 2008 for the continuous precipitation of lanthanides or actinides as oxalate, in order to either increase the production capacity or allow the precipitation of long-life radioactive elements under optimum safety conditions. During research/development tests, a strong correlation between the emulsion's properties and those of the particles produced have been evidenced, thus enabling the size and morphology of the powder to be tuned by varying the droplets properties, the latter being controlled by the column operating conditions. This process thus appears as an attractive alternative to conventional processes for the synthesis of high-value precipitates; as it offers interesting intensification capabilities. In this context, the feasibility of the precipitation of bismuth subnitrate (BSN), for which the emulsion route for precipitation seems to be particularly attractive, has been studied. Indeed, the division of the reacting volume into droplets may allow efficient temperature regulation of the exothermic reaction. In addition, an improvement of the product appearance is expected. This first phase of the feasibility study focused on the choice of the organic phase and the sensitivity of the droplets and solid particles properties to the operating conditions. Following the encouraging results observed in stirred-tank reactor, we successfully tested the implementation in a pulsed column, at lab-scale. (authors)

Innovative precipitation in emulsion process: toward a non-nuclear industrial application

Energy Technology Data Exchange (ETDEWEB)

Ollivier, M.; Borda, G.; Charton, S. [CEA, Centre de Marcoule, DEN,DTEC,SGCS, F-30207 Bagnols-sur-Ceze (France); Flouret, J. [OCM, ZI Quai Jean Jaures, 197 Avenue Marie Curie, 07800 La Voulte-sur-Rhone (France)

2016-07-01

A precipitation in emulsion process has been proposed by Borda et al. in 2008 for the continuous precipitation of lanthanides or actinides as oxalate, in order to either increase the production capacity or allow the precipitation of long-life radioactive elements under optimum safety conditions. During research/development tests, a strong correlation between the emulsion's properties and those of the particles produced have been evidenced, thus enabling the size and morphology of the powder to be tuned by varying the droplets properties, the latter being controlled by the column operating conditions. This process thus appears as an attractive alternative to conventional processes for the synthesis of high-value precipitates; as it offers interesting intensification capabilities. In this context, the feasibility of the precipitation of bismuth subnitrate (BSN), for which the emulsion route for precipitation seems to be particularly attractive, has been studied. Indeed, the division of the reacting volume into droplets may allow efficient temperature regulation of the exothermic reaction. In addition, an improvement of the product appearance is expected. This first phase of the feasibility study focused on the choice of the organic phase and the sensitivity of the droplets and solid particles properties to the operating conditions. Following the encouraging results observed in stirred-tank reactor, we successfully tested the implementation in a pulsed column, at lab-scale. (authors)

Development of soy lecithin based novel self-assembled emulsion hydrogels.

Science.gov (United States)

Singh, Vinay K; Pandey, Preeti M; Agarwal, Tarun; Kumar, Dilip; Banerjee, Indranil; Anis, Arfat; Pal, Kunal

2015-03-01

The current study reports the development and characterization of soy lecithin based novel self-assembled emulsion hydrogels. Sesame oil was used as the representative oil phase. Emulsion gels were formed when the concentration of soy lecithin was >40% w/w. Metronidazole was used as the model drug for the drug release and the antimicrobial tests. Microscopic study showed the apolar dispersed phase in an aqueous continuum phase, suggesting the formation of emulsion hydrogels. FTIR study indicated the formation of intermolecular hydrogen bonding, whereas, the XRD study indicated predominantly amorphous nature of the emulsion gels. Composition dependent mechanical and drug release properties of the emulsion gels were observed. In-depth analyses of the mechanical studies were done using Ostwald-de Waele power-law, Kohlrausch and Weichert models, whereas, the drug release profiles were modeled using Korsmeyer-Peppas and Peppas-Sahlin models. The mechanical analyses indicated viscoelastic nature of the emulsion gels. The release of the drug from the emulsion gels was diffusion mediated. The drug loaded emulsion gels showed good antimicrobial activity. The biocompatibility test using HaCaT cells (human keratinocytes) suggested biocompatibility of the emulsion gels. Copyright © 2015 Elsevier Ltd. All rights reserved.

Field testing of asphalt-emulsion radon-barrier system

International Nuclear Information System (INIS)

Hartley, J.N.; Freeman, H.D.; Baker, E.G.; Elmore, M.R.; Nelson, D.A.; Voss, C.F.; Koehmstedt, P.L.

1981-09-01

Three years of laboratory and field testing have demonstrated that asphalt emulsion seals are effective radon diffusion barriers. Both laboratory and field tests in 1979, 1980 and 1981 have shown that an asphalt emulsion seal can reduce radon fluxes by greater than 99.9%. The effective diffusion coefficient for the various asphalt emulsion admix seals averages about 10 -6 cm 2 /s. The 1981 joint field test is a culmination of all the technology developed to date for asphalt emulsion radon barrier systems. Preliminary results of this field test and the results of the 1980 field test are presented. 18 figures, 6 tables

Study on short-lived particles with emulsion techniques

International Nuclear Information System (INIS)

Prentis, D.D.

1984-01-01

Experiments on measuring the lifetimes are reviewed and the decay mechanisms for c-, b-quark, tau-lepton and charmed hadron are disclosed by means of emulsion chambers and hybride techniques (HT) of the emulsion-spectrometer type. The dominant development of hybride emulsion technique is traced beginning with the early experiments on measuring the lifetime of particles with emulsion (approximately 10 -13 s) and emulsion chambers. The layouts of arrangement of emulsions, counters and chambers are presented. Experiments on neutrino beams in the Fermilab and CERN using a foot bubble chamber and the Big European Bubble Chamber (BEBC) are briefly described. HT experiments with a muon beam and neutrino beams in the Fermilab, with a photon beam in CERN with the use of the modified Omega are considered in detail. The results on measuring the lifetimes of the particles investigated are presented. The lengths of decay tracks, hypothetical decays, fitted masses, leVels of permissible limit of kinematic analysis, pulses of charmed baryons and intrinsic lifetimes of candidates for decay Λsub(c)sup(+), D +- , D 0 , F + - mesons are tabulated. The maximum likelihood method has been applied to determine the lifetimes from complete data on decays. It is noted that new developments in the field of semiconductor detectors and automation of emulsion measurements can extend possibilities of HT for investigation of both charmed

Copolymerization and terpolymerization of carbon dioxide/propylene oxide/phthalic anhydride using a (salenCo(III complex tethering four quaternary ammonium salts

Directory of Open Access Journals (Sweden)

Jong Yeob Jeon

2014-08-01

Full Text Available The (salenCo(III complex 1 tethering four quaternary ammonium salts, which is a highly active catalyst in CO2/epoxide copolymerizations, shows high activity for propylene oxide/phthalic anhydride (PO/PA copolymerizations and PO/CO2/PA terpolymerizations. In the PO/PA copolymerizations, full conversion of PA was achieved within 5 h, and strictly alternating copolymers of poly(1,2-propylene phthalates were afforded without any formation of ether linkages. In the PO/CO2/PA terpolymerizations, full conversion of PA was also achieved within 4 h. The resulting polymers were gradient poly(1,2-propylene carbonate-co-phthalates because of the drift in the PA concentration during the terpolymerization. Both polymerizations showed immortal polymerization character; therefore, the molecular weights were determined by the activity (g/mol-1 and the number of chain-growing sites per 1 [anions in 1 (5 + water (present as impurity + ethanol (deliberately fed], and the molecular weight distributions were narrow (Mw/Mn, 1.05–1.5. Because of the extremely high activity of 1, high-molecular-weight polymers were generated (Mn up to 170,000 and 350,000 for the PO/PA copolymerization and PO/CO2/PA terpolymerization, respectively. The terpolymers bearing a substantial number of PA units (fPA, 0.23 showed a higher glass-transition temperature (48 °C than the CO2/PO alternating copolymer (40 °C.

Preparation of poly (methyl methacrylate)/nanometer calcium carbonate composite by in-situ emulsion polymerization

Institute of Scientific and Technical Information of China (English)

史建明; 包永忠; 黄志明; 翁志学

2004-01-01

Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate (nano-CaCO3) surface modified with (-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl methacrylate) (PMMA)/nano-CaCO3 composite. The reaction between nano-CaCO3 and MPTMS, and the grafting of PMMA onto nano-CaCO3 were confirmed by infrared spectrum. The grafting ratio and grafting efficiency of PMMA on nano-CaCO3 modified with MPTMS were much higher than that on nano-CaCO3 modified with stearic acid. The grafting ratio of PMMA increased as the weight ratio between MMA and nano-CaCO3 increased, while the grafting efficiency of PMMA decreased. Transmission electron micrograph showed that nano-CaCO3 covered with PMMA was formed by in-situ emulsion polymerization.

Binding of long-lasting local anesthetics to lipid emulsions.

Science.gov (United States)

Mazoit, Jean-Xavier; Le Guen, Régine; Beloeil, Hélène; Benhamou, Dan

2009-02-01

Rapid infusion of lipid emulsion has been proposed to treat local anesthetic toxicity. The authors wanted to test the buffering properties of two commercially available emulsions made of long- and of long- and medium-chain triglycerides. Using the shake-flask method, the authors measured the solubility and binding of racemic bupivacaine, levobupivacaine, and ropivacaine to diluted Intralipid (Fresenius Kabi, Paris, France) and Medialipide (B-Braun, Boulogne, France). The apparent distribution coefficient expressed as the ratio of mole fraction was 823 +/- 198 and 320 +/- 65 for racemic bupivacaine and levobupivacaine, and ropivacaine, respectively, at 500 mg in the Medialipide/buffer emulsion; and 1,870 +/- 92 and 1,240 +/- 14 for racemic bupivacaine and levobupivacaine, and ropivacaine, respectively, in the Intralipid/buffer emulsion. Decreasing the pH from 7.40 to 7.00 of the Medialipide/buffer emulsion led to a decrease in ratio of molar concentration from 121 +/- 3.8 to 46 +/- 2.8 for bupivacaine, and to a lesser extent from 51 +/- 4.0 to 31 +/- 1.6 for ropivacaine. The capacity of the 1% emulsions was 871 and 2,200 microM for the 1% Medialipide and Intralipid emulsions, respectively. The dissociation constant was 818 and 2,120 microM for racemic bupivacaine and levobupivacaine, and ropivacaine, respectively. Increasing the temperature from 20 to 37 degrees C led to a greater increase in affinity for ropivacaine (55%) than for bupivacaine (27%). When the pH of the buffer was decreased from 7.40 to 7.00, the affinity was decreased by a factor of 1.68, similar for both anesthetics. The solubility of long-acting local anesthetics in lipid emulsions and the high capacity of binding of these emulsions most probably explain their clinical efficacy in case of toxicity. The long-chain triglyceride emulsion Intralipid appears to be about 2.5 times more efficacious than the 50/50 medium-chain/long-chain Medialipide emulsion. Also, because of their higher hydrophobicity

Aging properties of Kodak type 101 emulsions

Science.gov (United States)

Dohne, B.; Feldman, U.; Neupert, W.

1984-01-01

Aging tests for several batches of Kodak type 101 emulsion show that storage conditions significantly influence how well the film will maintain its sensitometric properties, with sensitivity and density increasing to a maximum during this period. Any further aging may result in higher fog levels and sensitivity loss. It is noted that storage in an environment free of photographically active compounds allows film property optimization, and that film batches with different sensitivities age differently. Emulsions with maximum 1700-A sensitivity are 2.5 times faster than those at the low end of the sensitivity scale. These sensitive emulsions exhibit significantly accelerated changes in aging properties. Their use in space applications requires careful consideration of time and temperature profiles, encouraging the use of less sensitive emulsions when the controllability of these factors is limited.

Sardine Fish Oil By Sentrifugation and Adsorbent for Emulsion

Directory of Open Access Journals (Sweden)

Kristina Haryati

2017-04-01

Full Text Available Sardine fish meal by-product contain eicosapentaenoic acid (EPA and docosahexaenoic (DHA and it can be made as emulsion. The purpose of this study were to determine the best fish oil emulsion by mixingthe oil phase (lecithin 3% and oil and water phase (carboxymethyl cellulose/CMC 2% and fruit juice and then stored until creaming, and the emulsion is analyzed their viscosity, pH, percent of stability and longseparation. Sardine oil is separated from the emulsion and tested oxidation parameters. The best emulsion was fish oil emulsion after refined without citric acid (RTS with viscosity (2470.31 cP, pH (5.64, percent of stability (56.14% and long separation (14 days. Primary and secondary oxidation parameters of RTS  were FFA (14.87%, PV (14.43 meq/kg, AV (32.57 meq KOH/g, AnV (17.3 meq/kg, and Totox (46.16 meq/kg.

Oil-in-oil emulsions stabilised solely by solid particles.

Science.gov (United States)

Binks, Bernard P; Tyowua, Andrew T

2016-01-21

A brief review of the stabilisation of emulsions of two immiscible oils is given. We then describe the use of fumed silica particles coated with either hydrocarbon or fluorocarbon groups in acting as sole stabilisers of emulsions of various vegetable oils with linear silicone oils (PDMS) of different viscosity. Transitional phase inversion of emulsions, containing equal volumes of the two oils, from silicone-in-vegetable (S/V) to vegetable-in-silicone (V/S) occurs upon increasing the hydrophobicity of the particles. Close to inversion, emulsions are stable to coalescence and gravity-induced separation for at least one year. Increasing the viscosity of the silicone oil enables stable S/V emulsions to be prepared even with relatively hydrophilic particles. Predictions of emulsion type from calculated contact angles of a silica particle at the oil-oil interface are in agreement with experiment provided a small polar contribution to the surface energy of the oils is included. We also show that stable multiple emulsions of V/S/V can be prepared in a two-step procedure using two particle types of different hydrophobicity. At fixed particle concentration, catastrophic phase inversion of emulsions from V/S to S/V can be effected by increasing the volume fraction of vegetable oil. Finally, in the case of sunflower oil + 20 cS PDMS, the study is extended to particles other than silica which differ in chemical type, particle size and particle shape. Consistent with the above findings, we find that only sufficiently hydrophobic particles (clay, zinc oxide, silicone, calcium carbonate) can act as efficient V/S emulsion stabilisers.

The role of electrostatics in saliva-induced emulsion flocculation

NARCIS (Netherlands)

Silletti, Erika; Vingerhoeds, Monique H.; Norde, Willem; Van Aken, George A.

Upon consumption food emulsions undergo different processes, including mixing with saliva. It has been shown that whole saliva induces emulsion flocculation [van Aken, G. A., Vingerhoeds, M. H., & de Hoog, E. H. A. (2005). Colloidal behaviour of food emulsions under oral conditions. In E. Dickinson

A Recyclable Nanoparticle-Supported Rhodium Catalyst for Hydrogenation Reactions

Directory of Open Access Journals (Sweden)

Maria Michela Dell’Anna

2010-05-01

Full Text Available Catalytic hydrogenation under mild conditions of olefins, unsaturated aldeydes and ketones, nitriles and nitroarenes was investigated, using a supported rhodium complex obtained by copolymerization of Rh(cod(aaema [cod: 1,5-cyclooctadiene, aaema–: deprotonated form of 2-(acetoacetoxyethyl methacrylate] with acrylamides. In particular, the hydrogenation reaction of halonitroarenes was carried out under 20 bar hydrogen pressure with ethanol as solvent at room temperature, in order to minimize hydro-dehalogenation. The yields in haloanilines ranged from 85% (bromoaniline to 98% (chloroaniline.

Analytical advantages of copolymeric microspheres for fluorimetric sensing - tuneable sensitivity sensors and titration agents.

Science.gov (United States)

Stelmach, Emilia; Maksymiuk, Krzysztof; Michalska, Agata

2017-01-15

Analytical benefits related to application of copolymeric microspheres containing different number of carboxylic acid mers have been studied on example of acrylate copolymers. These structures can be used as a reagent in heterogeneous pH titration, benefiting from different number of reactive groups - i.e. different concentration of a titrant - within the series of copolymers. Thus introducing the same amount of different microspheres from a series to the sample, different amount of the titrant is introduced. Copolymeric microspheres also can be used as optical sensors - in this respect the increasing number of reactive groups in the series is useful to improve the analytical performance of microprobes - sensitivity of determination or/and response range. The increase in ion-permeability of the spheres with increasing number of reactive mers is advantageous. It is shown that for pH sensitive microspheres containing higher number of carboxyl groups the higher sensitivity for alkaline pH samples is observed for an indicator present in the beads. The significant increase of optical responses is related to enhanced ion transport within the microspheres. For zinc or potassium ions model sensors tested it was shown that by choice of pH conditions and type of microspheres from the series, the optical responses can be tuned - to enhance sensitivity for analyte concentration change as well as to change the response pattern from sigmoidal (higher sensitivity, narrow range) to linear (broader response range). For classical optode systems (e.g. microspheres containing an optical transducer - pH sensitive dye and optically silent ionophore - receptor) copolymeric microspheres containing carboxylic acid mers in their structure allow application of the sensor in alkaline pH range, which is usually inaccessible for applied optical transducer. Copyright © 2016 Elsevier B.V. All rights reserved.

Radiation-induced copolymerizations of perfluorovinyl acetic acid and its methyl ester with α-olefin

International Nuclear Information System (INIS)

Kawaguchi, M.; Watanabe, T.; Matsuda, O.; Tabata, Y.; Machi, S.

1981-01-01

Homopolymerizations and copolymerizations of perfluorovinyl acetic acid (FVA) and its methyl ester (MFVA) were carried out by γ radiation at a temperature of 25 0 C, a dose rate of 1 x 10 6 rad/hr, and FVA/α-olefin and MFVA/α-olefin ratios of 10/90-90/10 in the monomer mixture. FVA and MFVA gave small quantities of brown and greasy low-molecular-weight homopolymers. The polymerization rates of both FVA and MFVA were extremely small, as shown by the maximum G value of monomer consumption of 12. FVA and MFVA reacted with α-olefin to form waxlike copolymers. The copolymerization rates of both FVA and MFVA with α-olefin were remarkably larger than those of the homopolymerizations, particularly with ethylene. The polymer compositions of FVA/ethylene or MFVA/ethylene were nearly 1/2 over a wide range of the monomer compositions. The Mayo-Lewis method gave negative r 1 (FVA) and r 1 (MFVA). The polymer composition curves could be well interpreted by introducing the penultimate model

CMS emulsion pictures during LS1

CERN Multimedia

Di Ferdinando, Donato

2013-01-01

These images were taken at the CMS experimental cavern during Long Shutdown 1, installing pinhole cameras at different points of the cavern and exposing them for days. The development of the film was done by Donato di Ferdinando from INFN Bologna. A pinhole camera is a light-tight box where a small hole is made (diameter of the order of microns); a light-sensitive material is set in the back of the hole. As sensitive material a nuclear emulsion film from the OPERA experiment was used. It is a special photographic emulsion optimized (silver grains enriched) for the detection of charged particles. A very large amount of nuclear emulsions where used in Opera experiment, at the Gran Sasso Underground Labs; nuclear emulsions must detect the charged tau-leptons emerging from the interaction between the "oscillated" tau-neutrino coming from the pure muon-neutrino beam produced at CERN (the CNGS beam). The oscillations theory of neutrino expects that muon neutrinos oscillate to tau-neutrinos and due to this behavior ...

Development of lamivudine containing multiple emulsions stabilized by gum odina

Directory of Open Access Journals (Sweden)

Aditya Kumar Jena

2018-06-01

Full Text Available In the current study, a multiple emulsion (W/O/W of lamivudine was developed using a new biopolymer, gum odina (GOd to increase bioavailability and patient compliances. GOd was employed to stabilize both the interfaces of liquid membrane in both the external and internal aqueous phases. The developed W/O/W multiple emulsion of lamivudine was characterized by analyzing droplet size, zeta potential, polydispersity index (PDI, sedimentation, viscosity, rheological properties, drug entrapment efficiency, in-vitro drug release and stability at various storage conditions. The results obtained were also compared with W/O/W multiple emulsion of lamivudine prepared using Tween 80 (a standard emulsion stabilizer. The drug entrapment efficiency of W/O/W multiple emulsion stabilized using GOd was measured as 91.60 ± 3.66% with sustained lamivudine release over a period of 6 h. Rheological and microscopic examinations indicated long term stability of the developed emulsion prepared using GOd. The results of the current study provide a promising scope to attain sustained drug release through the W/O/W multiple emulsions stabilized by GOd in antiviral therapies. Keywords: Gum odina, Lamivudine, Multiple emulsions

Studies with a safflower oil emulsion in total parenteral nutrition.

Science.gov (United States)

Wong, K. H.; Deitel, M.

1981-01-01

The prevention of essential fatty acid deficiency and the provision of adequate amounts of energy are two major concerns in total parenteral nutrition. Since earlier preparations of fat emulsion used to supplement the usual regimen of hypertonic glucose and amino acids have widely varying clinical acceptability, a new product, a safflower oil emulsion available in two concentrations (Liposyn), was evaluated. In four clinical trials the emulsion was used as a supplement to total parenteral nutrition. In five surgical patients 500 ml of the 10% emulsion infused every third day prevented or corrected essential fatty acid deficiency; however, in some cases in infusion every other day may be necessary. In 40 patients in severe catabolic states the emulsion provided 30% to 50% of the energy required daily: 10 patients received the 10% emulsion for 14 to 42 days, 9 patients received each emulsion in turn for 7 days, and 21 patient received the 20% emulsion for 14 to 28 days. All the patients survived and tolerated the lipid well; no adverse clinical effects were attributable to the lipid infusions. Transient mild, apparently clinically insignificant abnormalities in the results of one or more liver function tests and eosinophilia were observed in some patients. Thus, the safflower oil emulsion, at both concentrations, was safe and effective as a source of 30% to 50% of the energy required daily by seriously ill patients. PMID:6799182

Bioequivalence and tolerability assessment of a novel intravenous ciclosporin lipid emulsion compared to branded ciclosporin in Cremophor ® EL

DEFF Research Database (Denmark)

Ehinger, Karl Henrik Johannes; Hansson, Magnus Joakim; Sjövall, Fredrik

2013-01-01

as emulsifying excipient. Cremophor(®) EL is known to cause hypersensitivity reactions in some patients, ranging from skin reactions to potentially fatal anaphylactic shock. OBJECTIVES: The primary objective was to assess if CicloMulsion(®), a Cremophor(®) EL-free lipid emulsion of ciclosporin for intravenous...... to current guidelines were performed. RESULTS: The geometric mean ratios for CicloMulsion(®)/Sandimmune(®) (90 % confidence interval [CI]) were 0.90 (0.88, 0.92) for AUC(0-last) (area under the blood concentration-time curve from time zero to time of last measurable concentration) and 0.95 (0.92, 0.97) for C...... adverse events were recorded after treatment with CicloMulsion(®). CONCLUSION: We have assessed the pharmacokinetics and tolerability of a new Cremophor(®) EL-free lipid emulsion of ciclosporin, CicloMulsion(®), compared to Sandimmune(®). The proportion of adverse events was significantly higher...

Gas Phase Homo- and Co-polymerization of Ethylene over Mg(O Et){sub 2}/T HF/Si Cl{sub 4}/Ti Cl{sub 4}/ Catalysts

Energy Technology Data Exchange (ETDEWEB)

Min-Chul, Chung [Korea Advanced Institute of Science and Techology., Taejeon (Korea, Republic of); Il, Kim [Univ. of Ulsan., Ulsan (Korea, Republic of); Jae-Ha, Kim [Korea Petrochemial Ind., Kyungnam (Korea, Republic of); Hong-Ki Choi [Korea Advanced Institute of Science and Technology., Taejeon (Korea, Republic of); Seung-Ihl, Woo

1994-08-01

Homo- and co-polymerization of ethylene were carried out in both gas and slurry phases over Mg(O Et)2/T HF/Si Cl{sub 4}/Ti Cl{sub 4}-Al Et{sub 3} catalysts in the range of temperature 20-70{sup o} C and pressure 2-10 psig. In gas phase polymerization, maximum activity was measured at the Al/Ti mole ratio of 377, and reaction rate dependence on Al Et{sub 3} concentration could be explained with the Langmuir-Hinshelwood adsorption model. Even though maximum activities were obtained at the same temperature, 60{sup o} C in both gas and slurry phases, overall activation energy was higher for the slurry phase(13 kCal/mol) than for the gas phase(4.7 kCal/mol) polymerization. The molecular weight behavior has been examined by measuring intrinsic viscosity. The molecular weight was increased as the ethylene pressure increased, and as the temperature and the concentration of Al Et{sub 3} and hydrogen decreased. Using two different co monomers(propylene and butene-1), the copolymerization of ethylene was carried out. The intrinsic viscosity and the melt index were decreased as co monomer concentration increased, and the maximum activity was observed when the concentration of comonomer is about 20 mol%. (author). 28 refs. 6 tabs. 13 figs.

Preparation of supramolecular polymers by copolymerization of monomers containing quadruple hydrogen bonding units with regular monomers

NARCIS (Netherlands)

2004-01-01

The invention relates to the synthesis of polymers containing self-complementary quadruple hydrogen groups by copolymerizing monomers containing a quadruple hydrogen bonding group with one or more monomers of choice. The resulting polymers show unique new characteristics due to the presence of

Track theory and nuclear photographic emulsions for Dark Matter searches

International Nuclear Information System (INIS)

Ditlov, V.A.

2013-01-01

This work is devoted to the analysis of possibilities of nuclear emulsions for Dark Matter search, particles of which can produce slow recoil-nuclei. Tracks of such recoil-nuclei in developed nuclear emulsion consist from several emulsion grains. The analysis was carried out with Monte-Carlo calculations made on the basis of the Track Theory and the various factors influencing Dark Matter particles registration efficiency were investigated. Problems, which should be solved for optimal utilization of nuclear emulsions in Dark Matter search, were formulated. B ody - Highlights: ► Specific features of Dark Matter Search in nuclear photographic emulsions. ► Track theory for WIMP search in nuclear emulsions. ► Primary efficiency for single WIMP registration. ► Properties of primary WIMP registration efficiency. ► Primary registration efficiency of WIMP flow

Use of Synthetic Polymers in Nuclear Emulsions for Fast-Neutron Dosimetry

International Nuclear Information System (INIS)

Bradna, F.

1967-01-01

The paper describes the results of tests on the properties of hydrogen-enriched nuclear-track emulsions for detecting fast neutrons, which were prepared in the Radiological Dosimetry Laboratory of the Czechoslovak Academy of Sciences Nuclear Research Institute. It also compares the dosimetric characteristics of these new emulsions with those of the gelatin emulsions used up to the present. The most promising of the series of polymers synthesized in the laboratory were: (1) Polyvinylacetal of 2,4-disulphonic acid benzaldehyde (polymer No. 1); (2) The co-polymer of a-acetylaminoacrylic acid and N-vinylpyrrolidone (polymer No. 2). The author also studied the possibility of using polyvinyl alcohol solutions with a higher hydrogen content than the above polymers for saturating polymer-gelatin emulsions and for preparing from them films for use as proton radiators. Polymers No. 1 and No. 2 were tested beforehand in an ammonia emulsion. It was established that polymer No. 1 has no marked effect on the photochemical properties of the emulsions, whereas the physical and mechanical.properties of the polymer-gelatin emulsions are considerably better than those of normal gelatin emulsions. The polymers have good protective properties, and polymer No. 2; can be used even during physical ageing, since it retards this process only to a small extent. The photochemical properties of the polymer-gelatin emulsions remain practically unchanged during natural ageing, and their mechanical strength is still further increased. After these preliminary tests, polymers No.-1 and No. 2 were used as fillers for a nuclear-track emulsion, in quantities ranging from 50 to 70% of the total amount of protective colloid, the silver content of the emulsion remaining unchanged. To increase their efficiency further, the polymer-gelatin emulsions were saturated with hydrogen, which was passed through the liquid emulsion for a short period of time. When prepared, the emulsions were poured on a tri

In-situ radiation dosimetry based on radio-fluorogenic co-polymerization

International Nuclear Information System (INIS)

Warman, John M; Luthjens, Leonard H; Haas, Matthijs P de

2009-01-01

A fluorimetric method of radiation dosimetry is presented for which the intensity of the fluorescence of a (tissue equivalent) medium is linearly dependent on accumulated dose from a few Gray up to kiloGrays. The method is based on radio-fluorogenic co-polymerization (RFCP) in which a normally very weakly fluorescent molecule becomes highly fluorescent when incorporated into a (radiation-initiated) growing polymer chain. The method is illustrated with results of in-situ measurements within the chamber of a cobalt-60 irradiator. It is proposed that RFCP could form the basis for fluorimetric multi-dimensional dose imaging.

Submicron Emulsions and Their Applications in Oral Delivery.

Science.gov (United States)

Mundada, Veenu; Patel, Mitali; Sawant, Krutika

2016-01-01

A "submicron emulsion" is an isotropic mixture of drug, lipids, and surfactants, usually with hydrophilic cosolvents and with droplet diameters ranging from 10 to 500 nm. Submicron emulsions are of increasing interest in medicine due to their kinetic stability, high solubilizing capacity, and tiny globule size. Because of these properties, they have been applied in various fields, such as personal care, cosmetics, health care, pharmaceuticals, and agrochemicals. Submicron emulsions are by far the most advanced nanoparticulate systems for the systemic delivery of biologically active agents for controlled drug delivery and targeting. They are designed mainly for pharmaceutical formulations suitable for various routes of administration like parenteral, ocular, transdermal, and oral. This review article describes the marked potential of submicron emulsions for oral drug delivery owing to their numerous advantages like reduced first pass metabolism, inhibition of P-glycoprotein efflux system, and enhanced absorption via intestinal lymphatic pathway. To overcome the limitations of liquid dosage forms, submicron emulsions can be formulated into solid dosage forms such as solid self-emulsifying systems. This article covers various types of submicron emulsions like microemulsion, nanoemulsion, and self-emulsifying drug delivery system (SEDDS), and their potential pharmaceutical applications in oral delivery with emphasis on their advantages, limitations, and advancements.

Immunomodulatory and Physical Effects of Oil Composition in Vaccine Adjuvant Emulsions

Science.gov (United States)

Fox, Christopher B.; Baldwin, Susan L.; Duthie, Malcolm S.; Reed, Steven G.; Vedvick, Thomas S.

2011-01-01

Squalene-based oil-in-water emulsions have been used for years in some seasonal and pandemic influenza vaccines. However, concerns have been expressed regarding squalene source and potential biological activities. Little information is available regarding the immunomodulatory activity of squalene in comparison with other metabolizable oils in the context of oil-in-water emulsions formulated with vaccines. The present work describes the manufacture and physical characterization of emulsions composed of different classes of oils, including squalene, long chain triglycerides, a medium chain triglyceride, and a perfluorocarbon, all emulsified with egg phosphatidylcholine. Some differences were apparent among the non-squalene oils in terms of emulsion stability, including higher size polydispersity in the perfluorocarbon emulsion, more rapid visual instability at 60 °C for the long-chain triglyceride and perfluorocarbon emulsions, and an increased creaming rate in the medium-chain triglyceride emulsion at 60 °C as detected by laser scattering optical profiling. The biological activity of each of these emulsions was compared when formulated with either a recombinant malaria antigen or a split-virus inactivated influenza vaccine. Overall, vaccines containing the squalene emulsion elicited higher antibody titers and more abundant long-lived plasma cells than vaccines containing emulsions based on other oils. Since squalene-based emulsions show higher adjuvant potency compared to the other oils tested, non-squalene oils may be more suitable as carriers of amphiphilic or hydrophobic immunostimulatory molecules (such as TLR agonists) rather than as stand-alone adjuvants. PMID:21906648

Centrifugal Pump Effect on Average Particle Diameter of Oil-Water Emulsion

Science.gov (United States)

Morozova, A.; Eskin, A.

2017-11-01

In this paper we review the process of oil-water emulsion particles fragmentation in a turbulent flow created by a centrifugal pump. We examined the influence of time necessary for oil-water emulsion preparation on the particle size of oil products and the dependence of a centrifugal pump emulsifying capacity on the initial emulsion dispersion. The investigated emulsion contained the brand fuel oil M-100 and tap water; it was sprayed with a nozzle in a gas-water flare. After preparation of the emulsion, the centrifugal pump was turned on and the emulsion samples were taken before and after the pump passing in 15, 30 and 45 minutes of spraying. To determine the effect the centrifugal pump has on the dispersion of the oil-water emulsion, the mean particle diameter of the emulsion particles was determined by the optical and microscopic method before and after the pump passing. A dispersion analysis of the particles contained in the emulsion was carried out by a laser diffraction analyzer. By analyzing the pictures of the emulsion samples, it was determined that after the centrifugal pump operation a particle size of oil products decreases. This result is also confirmed by the distribution of the obtained analyzer where the content of fine particles with a diameter less than 10 μm increased from 12% to 23%. In case of increasing emulsion preparation time, a particle size of petroleum products also decreases.

Experimental study of viscosity properties of emulsion system with SiO2 nanoparticles.

Directory of Open Access Journals (Sweden)

ZEIGMAN Yury Veniaminovich,

2017-04-01

emulsion systems showed stability of the systems under 80о C. In addition, the modified emulsion systems kept the ability to decrease significantly viscosity in the reaction with hydrocarbons, i.e. the emulsion systems with SiO2 nanoparticles are selective compositions for the water-inflows restriction.

Minimum pressure for sustained combustion in AN-based emulsions

Energy Technology Data Exchange (ETDEWEB)

Goldthorp, S.; Turcotte, R.; Badeen, C.M. [Natural Resources Canada, Ottawa, ON (Canada). Canadian Explosives Research Laboratory; Chan, S.K. [Orica Canada Inc., Brownsburg-Chatham, PQ (Canada)

2008-04-15

AN-based emulsions have been involved in a relatively high number of accidental explosions related to pumping operations during their manufacture, transfer and handling. The minimum burning pressure (MBP) of emulsions is used to estimate safe operating pressures for pumping and mixing equipment. This study examined testing protocols conducted to measure MBP values. Factors contributing to uncertainties in MBP data were examined, and a measurement methodology designed to incorporate the uncertainties was presented. MBP measurements obtained for 5 different AN-based emulsions in high pressure vessels were also provided, and the impact of various ingredients on MBP values was discussed. Bench-scale experiments and time current pulse tests were conducted to examine thermal ignition behaviour. The emulsions exhibited MBP values that ranged from 580 to 6510 kPa. Results of the study suggested that ingredients play a significant role on MBP values. A relatively high energy flux was required to induce stable combustion fronts in the emulsions. Large air voids containing flammable atmospheres were able to provide sufficient energy to ignite the emulsions. It was concluded that a knowledge of the MBP of emulsions is needed to ensure that corresponding pumping operations are conducted at pressures below the MBP. 11 refs., 2 tabs., 8 figs.

Nonionic emulsion-mediated synthesis of zeolite beta

Indian Academy of Sciences (India)

Zeolite beta synthesis was first carried out in a newly developed emulsion system containing nonionic polyoxyethylated alkylphenol surfactant, which showed interesting non-conventional features. Compared to the conventional hydrothermal synthesis of zeolite beta, the reported nonionic emulsion system showed a faster ...

Development of water-borne thermosetting paint by radiation-induced emulsion polymerization

International Nuclear Information System (INIS)

Makuuchi, K.; Katakai, A.; Nakayama, H.

1981-01-01

In previous papers the features of γ-ray induced emulsion polymerization were studied to use the emulsion as vehicles for water-borne paint. In this paper, the physical properties of thermosetting paints made with emulsions containing N-(n-butoxymethyl)acrylamide (NBM) and hydroxyl and carboxyl functionality were investigated. Since NBM moieties can react with amide, hydroxyl, and carboxyl groups, NBM copolymer emulsions prepared in this study have the self-crosslinking capability. As far as it was investigated, it was difficult to prepare a stable emulsion containing 10% of NBM by the conventional emulsion polymerization by using a water soluble radical initiator such as persulfate. In addition to 1-liter reactor, a pilot-scale plant of 70 liters reactor was used for γ-ray induced emulsion polymerization. Experimental details are given, and results are discussed. (author)

Evaluation of microcomputer assisted system for nuclear emulsion measurement, 2

International Nuclear Information System (INIS)

Sato, Yoshihiro; Tezuka, Ikuo; Izawa, Kazuo.

1983-01-01

In the reaction of hardrons of several hundreds GeV/c, charm particles with from 10 -12 to 10 -13 second lifetime and beauty particles of shorter lifetime are generated. For directly observing these particles, the experiment using a system which combines nuclear emulsion and an electronic counter is carried out. The authors have engaged in the development of a nuclear emulsion analyzing system since several years ago, and recently developed a program for that system, and made measurement using the program, as one of the works to participate in the NA-19 hybrid experiment of this type, which is a high energy experiment implemented with the CERN accelerator using 350 GeV/c π - beam. In this report, first the outline of NA-19 experiment, next the corresponding of counter coordinates to nuclear emulsions, and the search for candidate events, in which two or more muons exist, that passed iron and tungsten dampers, are described. Further, the measuring programs XPRED 5 and CRS 34 and the relationship between these programs and measuring procedure and the evaluation for them are described at the end. The present program allows the measurement of generated secondary particles without any trouble up to the distance of 5 mm downstream from the collision point. It was also found that the program was applicable to the measurement of the decay phenomena and kink of the particles expected in the measurement of short-life particles. The system capability of estimating the position of target particles within 10 μm greatly contributes to this. (Wakatsuki, Y.)

Nuclear interactions of 400 GeV protons in emulsion

International Nuclear Information System (INIS)

Otterlund, I.; Stenlund, E.; Andersson, B.

1978-04-01

We report on 400 GeV proton-emulsion nucleus reactions and compare the results to hadron-nucleus reactions at smaller energies. In particular we present results on the emission of fast target protons (essentially grey track particles) and on their correlation with the number of collisions inside the nucleus, ν, with the number of charged evaporated particles (essentially black particles) and with the number of pions produced (essentially shower particles). We observe that the main features of the 200-400 GeV data are very similar. However, we find that the mean shower-particle multiplicity at 400 GeV is essentially higher than expected from the simple independent particle model prediction = [1 + 0.5 ( - 1)]. The shower particle multiplicities do not seem to follow a target mass dependence of the form = A sup(α) with α = 0.19 as has been suggested in the literature. The pseudo-rapidity distribution shows limiting target and projectile fragmentation. The shower particle multiplicity in the ''central region'' increases linearily with but faster than 0.5 times the corresponding multiplicity in pp-reactions. (author)

Nuclear interactions of 400 GeV protons in emulsion

International Nuclear Information System (INIS)

Otterlund, I.; Stenlund, E.; Andersson, B.

1978-04-01

We report on 400 GeV proton-emulsion nucleus reactions and compare the results to hadron-nucleus reactions at smaller energies. In particular we present results on the emission of fast target protons (essentially grey track particles) and on their correlation with the number of collisions inside the nucleus, ν, with the number of charged evaporated particles (essentially black track particles) and with the number of pions produced (essentially shower particles). We observe that the main features of the 200-400 GeV data are very similar. However, we find that the mean shower-particle multiplicity at 400 GeV is essentially higher than expected from the simple independent particle model prediction = [1 + 0.5 ( - 1)]. The shower particle multiplicities do not seem to follow a target mass dependence of the form = Asup(α) with α = 0.14 or α = 0.19 as has been suggested in the literature. The pseudo-rapidity distribution shows limiting target and projectile fragmentation. The shower particle multiplicity in the ''central region'' increases linearily with but faster than 0.5 times the corresponding multiplicity in pp-reactions. (author)

Copolymerization of 4-Acetylphenyl Methacrylate with Ethyl Methacrylate: Synthesis, Characterization, Monomer Reactivity Ratios, and Thermal Properties

Directory of Open Access Journals (Sweden)

Gamze Barim

2014-01-01

Full Text Available Methacrylates have high glass transition temperature (Tg values and high thermal stability. A new methacrylate copolymer, poly(4-acetylphenyl methacrylate-co-ethyl methacrylate (APMA-co-EMA, was synthesized. The thermal behaviors of copolymers were investigated by differential scanning calorimetry and thermogravimetric analysis. They behaved as new single polymers with single Tg’s and the thermal stability of the copolymers increased with increasing 4-acetylphenyl methacrylate (APMA fraction, leading to the manufacture of copolymers with desired Tg values. Structure and composition of copolymers for a wide range of monomer feed ratios were determined by Fourier transform infrared (FT-IR and 1H-nuclear magnetic resonance (1H-NMR spectroscopic techniques. Copolymerization reactions were continued up to 40% conversions. The monomer reactivity ratios for copolymer system were determined by the Kelen-Tüdös (ra(APMA=0.81; rb(EMA=0.61 and extended Kelen-Tüdös (ra=0.77; rb=0.54 methods and a nonlinear least squares (ra=0.74; rb=0.49 method.

Polymerization of aniline in an organic peroxide system by the inverted emulsion process

OpenAIRE

Rao, Palle Swapna; Sathyanarayana, DN; Palaniappan, S

2002-01-01

An inverted emulsion process for the synthesis of the emeraldine salt of polyaniline using a novel oxidizing agent, namely benzoyl peroxide, is described. The polymerization is carried out in a nonpolar solvent in the presence of a functionalized protonic acid (sulfosalicylic acid) as the dopant and an emulsifier (sodium lauryl sulfate). The influence of synthesis conditions such as the duration of the reaction, temperature, concentration of the reactants, etc., on the properties of polyanili...

Antibacterial Modification of Microcrystalline Cellulose by Grafting Copolymerization

Directory of Open Access Journals (Sweden)

Ying Liu

2015-11-01

Full Text Available Microcrystalline cellulose (MCC has the advantage of a high specific surface area as compared to that of conventional cellulose fibers. In this study the monomer methacrylamide (MAM was used to treat MCC by grafting copolymerization. SEM, FTIR, and solid 13C NMR were used to characterize the morphology and composition of MAM-g-MCC. After the chlorination of MAM-g-MCC with 10% sodium hypochlorite solution, the grafted MCC exhibited antibacterial activity as a result of the formation of N-Cl bonds. The thermal stability, antibacterial ability, and storage stability of chlorinated MAM-g-MCC were also studied. The results showed that the chlorinated MAM-g-MCC had excellent storage stability and could inactivate all S. aureus and E. coli O157:H7 within 10 min.

Formulation and characterization of a multiple emulsion containing 1 ...

African Journals Online (AJOL)

The purpose of the study was to prepare a stable multiple emulsion containing a skin anti-aging agent and using paraffin oil. Vitamin C, was incorporated into the inner aqueous phase of water-in-oil-in-water (w/o/w) multiple emulsion at a concentration of 1%. Multiple emulsion was prepared by two step method. Stability ...

Ultrasonic Studies of Emulsion Stability in the Presence of Magnetic Nanoparticles

Directory of Open Access Journals (Sweden)

A. Józefczak

2015-01-01

Full Text Available Pickering emulsions are made of solid particle-stabilized droplets suspended in an immiscible continuous liquid phase. A magnetic emulsion can be obtained using magnetic particles. Solid magnetic nanoparticles are adsorbed strongly at the oil-water interface and are able to stabilize emulsions of oil and water. In this work emulsions stabilized by magnetite nanoparticles were obtained using high-energy ultrasound waves and a cavitation mechanism and, next, their stability in time was tested by means of acoustic waves with a low energy, without affecting the structure. An acoustic study showed high stability in time of magnetic emulsions stabilized by magnetite particles. The study also showed a strong influence of an external magnetic field, which can lead to changes of the emulsion properties. It is possible to control Pickering emulsion stability with the help of an external stimulus—a magnetic field.

Hydration process for calcium-aluminate cement within EVA emulsion by SPring-8 synchrotron radiation x-ray diffraction method

International Nuclear Information System (INIS)

Kotera, Masaru; Matsuda, Ikuyo; Miyashita, Keiko; Adachi, Nobuyuki; Tamura, Hisayuki

2005-01-01

Polymer-modified mortars which consist of a polymer emulsion and cement materials have been widely developed in the construction materials fields. Forming process of the polymer-modified cement membrane simultaneously involves evaporation of water within the polymer emulsion and hydration of cement. It is important for the polymer-modified cement paste that the hydrate crystal of cement is generating by the hydration during the setting process under existence of the polymer emulsion. In this study, hydration process for calcium-aluminate cement under existence of poly (ethylene-vinyl acetate) (EVA) emulsion (polymer-cement ratio=100%) was investigated by X-ray diffraction method using synchrotron radiation (SPring-8). The diffraction peaks of calcium aluminate (CA) disappeared after the hardening, on the other hand, the peaks of hydrate crystals of calcium-aluminate cement (C 2 AH 8 and C 3 AH 6 ) could be observed. This polymer-modified cement paste hydrated using the water within the polymer emulsion. The hydration of C 2 AH 8 from CA started at around 300 min, and then C 3 AH 6 hydrate crystal increased after 700 min at ambient temperature. This implies that the conversion from C 2 AH 8 to C 3 AH 6 occurred to be more stable phase. The setting temperature affected the reaction rate. In case of hydration at 35degC, the start time of the hydration for calcium-aluminate cement was quicker than that in the ambient temperature four or more times. (author)

Increasing of registering capacity of nuclear emulsion for autoradiography

International Nuclear Information System (INIS)

Romanovskaya, K.M.; Savvateeva, J.P.; Tolkacheva, E.N.

1977-01-01

The ways of increasing detecting power of the type M nuclear emulsion gel have been investigated in these studies. There have been found conditions under which type M emulsion sensitivity increased by 15 to 20% without increasing fog grain background. The stability of photographic sensitivity during emulsion gel storage increased by two times. The prevention of latent image fading (by means of layer moisture content) decreased to 1.2% and increasing the detecting power of the emulsion (by means of exposure temperature) by up to 37 0 C. The exposure time of tritium labelled autographs has been decreased to about 20%. (author)

Copolymerization preparation of cationic cyclodextrin chiral stationary phases for drug enantioseparation in chromatography

OpenAIRE

sprotocols

2015-01-01

Authors: Ren-Qi Wang, Teng-Teng Ong, Ke Huang, Weihua Tang & Siu-Choon Ng ### Abstract We described a facile and effective protocol wherein radical copolymerization is employed to covalently bond cationic β-cyclodextrin (β-CD) onto silica particles with extended linkage, resulting in a chiral stationary phase (IMPCSP) that can be used for the enantioseparation of racemic drugs in both high-performance liquid chromatography (HPLC) and supercritical fluid chromatography (SFC). Starting ...

Interactions between Parenteral Lipid Emulsions and Container Surfaces.

Science.gov (United States)

Gonyon, Thomas; Tomaso, Anthony E; Kotha, Priyanka; Owen, Heather; Patel, Dipa; Carter, Phillip W; Cronin, Jim; Green, John-Bruce D

2013-01-01

To evaluate the relationship between changes in emulsion globule size distributions and container uptake of lipid emulsions in total nutrient admixtures. A total nutrient admixture was prepared from a commercial lipid emulsion, 20% ClinOleic®, separated into glass (borosilicate) and ethylene vinyl acetate (EVA) plastic containers, and then stored at ambient conditions for approximately 24 h. The large globule size distribution was monitored continuously for both containers, and the quantity of triglycerides associated with both containers was measured by liquid chromatography. The changes in mass of the EVA containers were also measured gravimetrically. The volume percent of globules greater than 5 microns in diameter (PFAT5) levels for an emulsion admixture in EVA containers showed a 75% reduction compared to a marginal decrease of PFAT5 when in the glass container. Extraction of the containers showed that the quantity of triglycerides associated with the EVA surfaces steadily increased with emulsion exposure time, while the glass showed a significantly lower triglyceride content compared to the EVA. Gravimetric measurements confirmed that the EVA containers gained significant mass during exposure to the emulsion admixture. A time-dependent decrease in PFAT5 values for an emulsion admixture was associated with container triglyceride absorption where EVA containers had a greater uptake than glass containers. The larger globules appear to absorb preferentially, and the admixture globule size distribution fraction represented by PFAT5 accounts for 15-20% of the total triglyceride adsorption to the container. The goal of this work is to evaluate how emulsions in total nutrition admixtures are affected by the containers within which they are stored. Specifically, the study examines how the emulsion globule size distribution in different containers is related to adsorption or absorption of the lipids onto or into the container. The admixtures were prepared from a

KINETICS OF SUSPENDED EMULSION POLYMERIZATION OF METHYL METHACRYLATE

Institute of Scientific and Technical Information of China (English)

Yong-zhong Bao; Cheng-xi Wang; Zhi-ming Huang; Zhi-xue Weng

2004-01-01

The kinetics of suspended emulsion polymerization of methyl methacrylate (MMA), in which water acted as the dispersed phase and the mixture of MMA and cyclohexane as the continuous phase, was investigated. It showed that the initial polymerization rate (Rp0) and steady-state polymerization rate (Rp) were proportional to the mass ratio between water and oil phase, and increased as the polymerization temperature, the potassium persulphate concentration ([I]) and the Tween20 emulsifier concentration ([S]) increased. The relationships between the polymerization rate and [I] and [S] were obtained as follows: Rp0 ∝ [I]0.73[S]0.32 and Rp ∝ [I]0.71[S]0.23. The above exponents were close to those obtained from normal MMA emulsion polymerization. It also showed that the average molecular weight of the resulting poly(methyl methacrylate) decreased as the polymerization temperature, [I] and [S] increased. Thus, MMA suspended emulsion polymerization could be considered as a combination of many miniature emulsion polymerizations proceeding in water drops and obeyed the classical kinetics of MMA emulsion polymerization.

An update on safety and immunogenicity of vaccines containing emulsion-based adjuvants.

Science.gov (United States)

Fox, Christopher B; Haensler, Jean

2013-07-01

With the exception of alum, emulsion-based vaccine adjuvants have been administered to far more people than any other adjuvant, especially since the 2009 H1N1 influenza pandemic. The number of clinical safety and immunogenicity evaluations of vaccines containing emulsion adjuvants has correspondingly mushroomed. In this review, the authors introduce emulsion adjuvant composition and history before detailing the most recent findings from clinical and postmarketing data regarding the effects of emulsion adjuvants on vaccine immunogenicity and safety, with emphasis on the most widely distributed emulsion adjuvants, MF59® and AS03. The authors also present a summary of other emulsion adjuvants in clinical development and indicate promising avenues for future emulsion-based adjuvant development. Overall, emulsion adjuvants have demonstrated potent adjuvant activity across a number of disease indications along with acceptable safety profiles.

Nano-emulsions of fluorinated trityl radicals as sensors for EPR oximetry

Science.gov (United States)

Charlier, N.; Driesschaert, B.; Wauthoz, N.; Beghein, N.; Préat, V.; Amighi, K.; Marchand-Brynaert, J.; Gallez, B.

2009-04-01

This article reports the development and evaluation of two nano-emulsions (F45T-03/HFB and F15T-03/PFOB) containing fluorinated trityl radicals dissolved in perfluorocarbons. Preparation with a high-pressure homogenizer conferred sub-micronic size to both nano-emulsions. In vitro and in vivo EPR spectroscopy showed that the nano-emulsions had much greater oxygen sensitivity than the hydrophilic trityl, CT-03. In vivo experiments in rodents confirmed the ability of the nano-emulsions to follow the changes in oxygen concentration after induced ischemia. Histological evaluation of the tissue injected with the nano-emulsions revealed some acute toxicity for the F45T-03/HFB nano-emulsion but none for the F15T-03/PFOB nano-emulsion. These new formulations should be considered for further EPR oximetry experiments in pathophysiological situations where subtle changes in tissue oxygenation are expected.

Emulsions inside Gargamelle

CERN Multimedia

1978-01-01

A feasibility test was made with a 2.5 litre emulsion stack installed within the chamber. The stack was contained in a thermally insulated aluminium alloy pressure vessel (photo). See Annual Report 1978 p. 79 Fig. 5.

Instant polysaccharide-based emulsions: impact of microstructure on lipolysis.

Science.gov (United States)

Torcello-Gómez, Amelia; Foster, Timothy J

2017-06-21

The development of emulsion-based products through optimisation of ingredients, reduction in energy-input during manufacture, while fulfilling healthy attributes, are major objectives within the food industry. Instant emulsions can meet these features, but comprehensive studies are necessary to investigate the effect of the initial formulation on the final microstructure and, in turn, on the in vitro lipolysis, comprising the double aim of this work. The instant emulsion is formed within 1.5-3 min after pouring the aqueous phase into the oil phase which contains a mixture of emulsifier (Tween 20), swelling particles (Sephadex) and thickeners (hydroxypropylmethylcellulose, HPMC, and guar gum, GG) under mild shearing (180 rpm). The creation of oil-in-water emulsions is monitored in situ by viscosity analysis, the final microstructure visualised by microscopy and the release of free fatty acids under simulated intestinal conditions quantified by titration. Increasing the concentration and molecular weight (M w ) of GG leads to smaller emulsion droplets due to increased bulk viscosity upon shearing. This droplet size reduction is magnified when increasing the M w of HPMC or swelling capacity of viscosifying particles. In addition, in the absence of the emulsifier Tween 20, the sole use of high-Mw HPMC is effective in emulsification due to combined increased bulk viscosity and interfacial activity. Hence, optimisation of the ingredient choice and usage level is possible when designing microstructures. Finally, emulsions with larger droplet size (>20 μm) display a slower rate and lower extent of lipolysis, while finer emulsions (droplet size ≤20 μm) exhibit maximum rate and extent profiles. This correlates with the extent of emulsion destabilisation observed under intestinal conditions.

Logarithmic Exchange Kinetics in Monodisperse Copolymeric Micelles

Science.gov (United States)

García Daza, Fabián A.; Bonet Avalos, Josep; Mackie, Allan D.

2017-06-01

Experimental measurements of the relaxation kinetics of copolymeric surfactant exchange for micellar systems unexpectedly show a peculiar logarithmic decay. Several authors use polydispersity as an explanation for this behavior. However, in coarse-grained simulations that preserve microscopic details of the surfactants, we find evidence of the same logarithmic behavior. Since we use a strictly monodisperse distribution of chain lengths such a relaxation process cannot be attributed to polydispersity, but has to be caused by an inherent physical process characteristic of this type of system. This is supported by the fact that the decay is specifically logarithmic and not a power law with an exponent inherited from the particular polydispersity distribution of the sample. We suggest that the degeneracy of the energy states of the hydrophobic block in the core, which is broken on leaving the micelle, can qualitatively explain the broad distribution of energy barriers, which gives rise to the observed nonexponential relaxation.

Kinetics and thermodynamics of living copolymerization processes.

Science.gov (United States)

Gaspard, Pierre

2016-11-13

Theoretical advances are reported on the kinetics and thermodynamics of free and template-directed living copolymerizations. Until recently, the kinetic theory of these processes had only been established in the fully irreversible regime, in which the attachment rates are only considered. However, the entropy production is infinite in this regime and the approach to thermodynamic equilibrium cannot be investigated. For this purpose, the detachment rates should also be included. Inspite of this complication, the kinetics can be exactly solved in the regimes of steady growth and depolymerization. In this way, analytical expressions are obtained for the mean growth velocity, the statistical properties of the copolymer sequences, as well as the thermodynamic entropy production. The results apply to DNA replication, transcription and translation, allowing us to understand important aspects of molecular evolution.This article is part of the themed issue 'Multiscale modelling at the physics-chemistry-biology interface'. © 2016 The Author(s).

Structure- and oil type-based efficacy of emulsion adjuvants.

Science.gov (United States)

Jansen, Theo; Hofmans, Marij P M; Theelen, Marc J G; Manders, Frans; Schijns, Virgil E J C

2006-06-29

Oil-based emulsions are well-known immunopotentiators for inactivated, "killed" vaccines. We addressed the relationship between emulsion structure and levels of in vivo antibody formation to inactivated New Castle Disease virus (NDV) and Infectious Bronchitis virus (IBV) as antigens in 3-week-old chickens. The use of a polymeric emulsifier allowed for direct comparison of three types of emulsions, water-in-oil (W/O), oil-in-water (O/W) and W/O-in-water (W/O/W), while maintaining an identical content of components for each vehicle. They were prepared with either non-metabolizable, mineral oil or metabolizable, Miglyol 840. In addition, we assessed the inherent release capacity of each emulsion variant in vitro. Remarkably, we noted that W/O-type emulsions induced the best immune responses, while they released no antigen during 3 weeks. In general, mineral oil vaccines showed superior efficacy compared to Miglyol 840-based vaccines.

Rheological behavior of water-in-oil emulsions stabilized by hydrophobic bentonite particles.

Science.gov (United States)

Binks, Bernard P; Clint, John H; Whitby, Catherine P

2005-06-07

A study of the rheological behavior of water-in-oil emulsions stabilized by hydrophobic bentonite particles is described. Concentrated emulsions were prepared and diluted at constant particle concentration to investigate the effect of drop volume fraction on the viscosity and viscoelastic response of the emulsions. The influence of the structure of the hydrophobic clay particles in the oil has also been studied by using oils in which the clay swells to very different extents. Emulsions prepared from isopropyl myristate, in which the particles do not swell, are increasingly flocculated as the drop volume fraction increases and the viscosity of the emulsions increases accordingly. The concentrated emulsions are viscoelastic and the elastic storage and viscous loss moduli also increase with increasing drop volume fraction. Emulsions prepared from toluene, in which the clay particles swell to form tactoids, are highly structured due to the formation of an integrated network of clay tactoids and drops, and the moduli of the emulsions are significantly larger than those of the emulsions prepared from isopropyl myristate.

Natural Oil-Based Emulsion Containing Allantoin Versus Aqueous Cream for Managing Radiation-Induced Skin Reactions in Patients With Cancer: A Phase 3, Double-Blind, Randomized, Controlled Trial

International Nuclear Information System (INIS)

Chan, Raymond Javan; Mann, Jennifer; Tripcony, Lee; Keller, Jacqui; Cheuk, Robyn; Blades, Rae; Keogh, Samantha; Poole, Christopher; Walsh, Christopher

2014-01-01

Purpose: To investigate the effects of a natural oil-based emulsion containing allantoin versus aqueous cream for preventing and managing radiation-induced skin reactions. Methods and Materials: A total of 174 patients were randomized and participated in the study. Patients received either cream 1 (the natural oil-based emulsion containing allantoin) or cream 2 (aqueous cream). Skin toxicity, pain, itching, and skin-related quality of life scores were collected for up to 4 weeks after radiation treatment. Results: Patients who received cream 1 had a significantly lower average level of Common Terminology Criteria for Adverse Events at week 3 (P<.05) but had statistically higher average levels of skin toxicity at weeks 7, 8, and 9 (all P<.001). Similar results were observed when skin toxicity was analyzed by grades. With regards to pain, patients in the cream 2 group had a significantly higher average level of worst pain (P<.05) and itching (P=.046) compared with the cream 1 group at week 3; however, these differences were not observed at other weeks. In addition, there was a strong trend for cream 2 to reduce the incidence of grade 2 or more skin toxicity in comparison with cream 1 (P=.056). Overall, more participants in the cream 1 group were required to use another topical treatment at weeks 8 (P=.049) and 9 (P=.01). Conclusion: The natural oil-based emulsion containing allantoin seems to have similar effects for managing skin toxicity compared with aqueous cream up to week 5; however, it becomes significantly less effective at later weeks into the radiation treatment and beyond treatment completion (week 6 and beyond). There were no major differences in pain, itching, and skin-related quality of life. In light of these results, clinicians and patients can base their decision on costs and preferences. Overall, aqueous cream seems to be a more preferred option

Natural Oil-Based Emulsion Containing Allantoin Versus Aqueous Cream for Managing Radiation-Induced Skin Reactions in Patients With Cancer: A Phase 3, Double-Blind, Randomized, Controlled Trial

Energy Technology Data Exchange (ETDEWEB)

Chan, Raymond Javan, E-mail: email.rchan@gmail.com [Cancer Care Services, Royal Brisbane and Women' s Hospital, Herston, Queensland (Australia); School of Nursing, Queensland University of Technology, Kelvin Grove (Australia); Institute of Health and Biomedical Innovation, Queensland University of Technology, Kelvin Grove (Australia); Mann, Jennifer; Tripcony, Lee; Keller, Jacqui; Cheuk, Robyn; Blades, Rae [Cancer Care Services, Royal Brisbane and Women' s Hospital, Herston, Queensland (Australia); Keogh, Samantha [National Health and Medical Research Council Centre for Research Excellence in Nursing, Centre for Health Practice Innovation–Griffith Health Institute, Griffith University, Nathan (Australia); Poole, Christopher [Cancer Care Services, Royal Brisbane and Women' s Hospital, Herston, Queensland (Australia); Science and Engineering Faculty, Queensland University of Technology, Brisbane (Australia); Walsh, Christopher [Cancer Care Services, Royal Brisbane and Women' s Hospital, Herston, Queensland (Australia)

2014-11-15

Purpose: To investigate the effects of a natural oil-based emulsion containing allantoin versus aqueous cream for preventing and managing radiation-induced skin reactions. Methods and Materials: A total of 174 patients were randomized and participated in the study. Patients received either cream 1 (the natural oil-based emulsion containing allantoin) or cream 2 (aqueous cream). Skin toxicity, pain, itching, and skin-related quality of life scores were collected for up to 4 weeks after radiation treatment. Results: Patients who received cream 1 had a significantly lower average level of Common Terminology Criteria for Adverse Events at week 3 (P<.05) but had statistically higher average levels of skin toxicity at weeks 7, 8, and 9 (all P<.001). Similar results were observed when skin toxicity was analyzed by grades. With regards to pain, patients in the cream 2 group had a significantly higher average level of worst pain (P<.05) and itching (P=.046) compared with the cream 1 group at week 3; however, these differences were not observed at other weeks. In addition, there was a strong trend for cream 2 to reduce the incidence of grade 2 or more skin toxicity in comparison with cream 1 (P=.056). Overall, more participants in the cream 1 group were required to use another topical treatment at weeks 8 (P=.049) and 9 (P=.01). Conclusion: The natural oil-based emulsion containing allantoin seems to have similar effects for managing skin toxicity compared with aqueous cream up to week 5; however, it becomes significantly less effective at later weeks into the radiation treatment and beyond treatment completion (week 6 and beyond). There were no major differences in pain, itching, and skin-related quality of life. In light of these results, clinicians and patients can base their decision on costs and preferences. Overall, aqueous cream seems to be a more preferred option.

Vinyl Acetate/butyl acrylate/acrylate Research of Ternary Soap-free Emulsion Polymerization

Directory of Open Access Journals (Sweden)

Xiao Li-guang

2016-01-01

Full Text Available Through the vinyl acetate/butyl acrylate/acrylic acrylic emulsion preparation without soap vinegar, with solid content, gel, emulsion stability and film forming properties and tensile strength as the main index to study the effect of raw materials on the properties of emulsion. Through the infrared spectrometer soap-free emulsion for microscopic analysis research. Study of the ternary soap-free vinegar acrylic emulsion with good performance.

Investigation of factors affecting slurry copolymerization of acrylo nitrite-vinylacetate for preparation of acrylic fibers

International Nuclear Information System (INIS)

Hajian, M.; Tavakoli, T.; Azarnasab, M.; Hossepian, M.

2001-01-01

Since 1978, acrylic fibers have been prepared by slurry polymerization comprising of about 94% acrylonitrile (A N) and 6% methyl methacrylate (M A) as a comonomer to a make bulky polymer and improve the dye ability of acrylic fibers in a continuous process by redox initiator (potassium persulfate and ammonium, ferrous sulfate). The slurry polymer obtained after neutralization, washing and drying are converted to polymer powder. The polymer is dissolved in dimethyl formamide (Dmf) and converted to acrylic fibers. Since 1998, it has been suggested that M A may be replaced by vinylacetate (V Ac), because V Ac has properties like M A and is a monomer produced by Arak Petrochemical CO. Therefore, in this project A N and V Ac were polymerized under the same conditions of A N and M A copolymerization process. Many tests have been carried out on the resulted polymer such as IR, viscosity, particle size, Whiteness of polymer powder and similar results were obtained as in the for former copolymer. In this work some important factors such as concentration of V Ac, time and temperature of polymerization reaction and also speed of agitator have been optimized

Rheological Behaviour of Water-in-Light Crude Oil Emulsion

Science.gov (United States)

Husin, H.; Taju Ariffin, T. S.; Yahya, E.

2018-05-01

Basically, emulsions consist of two immiscible liquids which have different density. In petroleum industry, emulsions are undesirable due to their various costly problems in term of transportation difficulties and production loss. A study of the rheological behaviour of light crude oil and its mixture from Terengganu were carried out using Antoon Paar MCR 301 rheometer operated at pressure of 2.5 bar at temperature C. Water in oil emulsions were prepared by mixing light crude oil with different water volume fractions (20%, 30% and 40%). The objectives of present paper are to study the rheological behaviour of emulsion as a fuction of shear rate and model analysis that fitted with the experimental data. The rheological models of Ostwald-De-Waele and Herschel-Bulkley were fitted to the experimental results. All models represented well the rheological data, with high values for the correlation coefficients. The result indicated that variation of water content influenced shear rate-shear stress rheogram of the prepared emulsions. In the case of 100% light crude oil, the study demonstrated non-Newtonian shear thickening behavior. However, for emulsion with different volume water ratios, the rheological behaviour could be well described by Herschel-Bulkley models due to the present of yield stress parameter (R2 = 0.99807). As a conclusion, rheological studies showed that volume water ratio have a great impact on the shear stress and viscosity of water in oil emulsion and it is important to understand these factors to avoid various costly problems.

Preparation of poly （methyl methacrylate）／nanometer calcium carbonate composite by in-situ emulsion polymerization

Institute of Scientific and Technical Information of China (English)

史建明; 包永忠; 黄志明; 翁志学

2004-01-01

Methyl methacrylate (MMA) emulsion polymerization in the presence of nanometer calcium carbonate(nano-CaCO3) surface modified with γ-methacryloxypropyltrimethoxysilane (MPTMS) was carried out to prepare poly (methyl methacrylate) (PMMA)/nano-CaCO3 composite. The reaction between nano-CaCO3 and MPTMS, and the grafting of PMMA onto nano-CaCO3 were confirmed by infrared spectrum. The grafting ratio and grafting efficiency of PMMA on nano-CaCO3 modified with MPTMS were much higher than that on nano-CaCO3 modified with stearic acid. The grafting ratio of PMMA increased as the weight ratio between MMA and nano-CaCO3 increased, while the grafting efficiency of PMMA decreased. Transmission electron micrograph showed that nano-CaCO3 covered with PMMA was formed by in-situ emulsion polymerization.

Emulsion design for the delivery of β-carotene in complex food systems.

Science.gov (United States)

Mao, Like; Wang, Di; Liu, Fuguo; Gao, Yanxiang

2018-03-24

β-Carotene has been widely investigated both in the industry and academia, due to its unique bioactive attributes as an antioxidant and pro-vitamin A. Many attempts were made to design delivery systems for β-carotene to improve its dispersant state and chemical stability, and finally to enhance the functionality. Different types of oil-in-water emulsions were proved to be effective delivery systems for lipophilic bioactive ingredients, and intensive studies were performed on β-carotene emulsions in the last decade. Emulsions are thermodynamically unstable, and emulsions with intact structures are preferable in delivering β-carotene during processing and storage. β-Carotene in emulsions with smaller particle size has poor stability, and protein-type emulsifiers and additional antioxidants are effective in protecting β-carotene from degradation. Recent development in the design of protein-polyphenol conjugates has provided a novel approach to improve the stability of β-carotene emulsions. When β-carotene is consumed, its bioaccessibility is highly influenced by the digestion of lipids, and β-carotene in smaller oil droplets containing long-chain fatty acids has a higher bioaccessibility. In order to better deliver β-carotene in complex food products, some novel emulsions with tailor-made structures have been developed, e.g., multilayer emulsions, solid lipid particles, Pickering emulsions. This review summarizes the updated understanding of emulsion-based delivery systems for β-carotene, and how emulsions can be better designed to fulfill the benefits of β-carotene in functional foods.

Evaporation of Particle-Stabilized Emulsion Sunscreen Films.

Science.gov (United States)

Binks, Bernard P; Fletcher, Paul D I; Johnson, Andrew J; Marinopoulos, Ioannis; Crowther, Jonathan M; Thompson, Michael A

2016-08-24

We recently showed (Binks et al., ACS Appl. Mater. Interfaces, 2016, DOI: 10.1021/acsami.6b02696) how evaporation of sunscreen films consisting of solutions of molecular UV filters leads to loss of UV light absorption and derived sun protection factor (SPF). In the present work, we investigate evaporation-induced effects for sunscreen films consisting of particle-stabilized emulsions containing a dissolved UV filter. The emulsions contained either droplets of propylene glycol (PG) in squalane (SQ), droplets of SQ in PG or droplets of decane in PG. In these different emulsion types, the SQ is involatile and shows no evaporation, the PG is volatile and evaporates relatively slowly, whereas the decane is relatively very volatile and evaporates quickly. We have measured the film mass and area, optical micrographs of the film structure, and the UV absorbance spectra during evaporation. For emulsion films containing the involatile SQ, evaporation of the PG causes collapse of the emulsion structure with some loss of specular UV absorbance due to light scattering. However, for these emulsions with droplets much larger than the wavelength of light, the light is scattered only at small forward angles so does not contribute to the diffuse absorbance and the film SPF. The UV filter remains soluble throughout the evaporation and thus the UV absorption by the filter and the SPF remain approximately constant. Both PG-in-SQ and SQ-in-PG films behave similarly and do not show area shrinkage by dewetting. In contrast, the decane-in-PG film shows rapid evaporative loss of the decane, followed by slower loss of the PG resulting in precipitation of the UV filter and film area shrinkage by dewetting which cause the UV absorbance and derived SPF to decrease. Measured UV spectra during evaporation are in reasonable agreement with spectra calculated using models discussed here.

The choice of homogenisation equipment affects lipid oxidation in emulsions

DEFF Research Database (Denmark)

Horn, Anna Frisenfeldt; Nielsen, Nina Skall; Jensen, Louise Helene Søgaard

2012-01-01

in emulsions has been shown to be affected by the emulsification conditions. The objective of this study was to investigate the influence of homogenisation equipment (microfluidizer vs. two-stage valve homogeniser) on lipid oxidation in 10% fish oil-in-water emulsions prepared with two different milk proteins....... Emulsions were prepared at pH 7 with similar droplet sizes. Results showed that the oxidative stability of emulsions prepared with sodium caseinate was not influenced by the type of homogeniser used. In contrast, the type of homogenisation equipment significantly influenced lipid oxidation when whey protein...

Physical stability of R-(+)-Limonene emulsions stabilized by Ulva fasciata algae polysaccharide.

Science.gov (United States)

Shao, Ping; Ma, Huiling; Qiu, Qiang; Jing, Weiping

2016-11-01

The physical stability of R-(+)-Limonene emulsions stabilized by Ulva fasciata polysaccharide (UFP) was investigated in this study. Emulsion physical stability was evaluated under different polysaccharide concentrations (1%-5%, wt/wt) and pH values (3.0-11.0). The stability of R-(+)-Limonene emulsions was demonstrated by droplet size distribution, rheological properties, zeta potential and visual phase separation. R-(+)-Limonene emulsions displayed monomodal droplet size distributions, high absolute values of zeta potential and good storage stability when 3% (wt/wt) UFP was used. The rheological properties and stability of R-(+)-Limonene emulsions appeared to be dependent on polysaccharide concentration. The emulsion stability was impacted by pH. Higher zeta potential (-52.6mV) and smaller mean droplet diameter (2.45μm) were achieved in neutral liquid environment (pH 7.0). Extreme acidity caused the flocculation of emulsions, which was manifested as phase separation, while emulsions were quite stable in an alkaline environment. Through comparing the stabilities of emulsions stabilized by different emulsifiers (i.e. UFP, GA and Gelatin), the result suggested that UFP was the best emulsifying agent among them. Copyright © 2016 Elsevier B.V. All rights reserved.

Tweens demulsification effects on heavy crude oil/water emulsion

Directory of Open Access Journals (Sweden)

Nastaran Hayati Roodbari

2016-09-01

Full Text Available The demulsification role of Tweens (nonionic polymers was determined in the separation of water from heavy crude oil emulsion. According to the previous researches, these nonionic polymers, having hydrophilic and lipophilic groups, are appropriate for making oil in water emulsion. In this research their effects in certain concentrations on demulsifying of water in crude oil emulsion were proved. High molecular weight, alkenes’ chains and groups of ketone and ester in these polymers can improve their performance for the demulsification of water in crude oil emulsion. Their efficiencies are improved with electronegative groups such as oxygen. They leave no corrosion effect because they are neutral and do not leave counter ions.

Fine grained nuclear emulsion for higher resolution tracking detector

Energy Technology Data Exchange (ETDEWEB)

Naka, T., E-mail: naka@flab.phys.nagoya-u.ac.jp [Institute of Advanced Research, Nagoya University, Nagoya (Japan); Asada, T.; Katsuragawa, T.; Hakamata, K.; Yoshimoto, M.; Kuwabara, K.; Nakamura, M.; Sato, O.; Nakano, T. [Graduated School of Science, Nagoya University, Nagoya (Japan); Tawara, Y. [Division of Energy Science, EcoTopia Science Institute, Nagoya University, Nagoya (Japan); De Lellis, G. [INFN Sezione di Napoli, Napoli (Italy); Sirignano, C. [INFN Sezione di Padova, Padova (Italy); D' Ambrossio, N. [INFN, Laboratori Nazionali del Gran Sasso, Assergi (L' Aquila) (Italy)

2013-08-01

Fine grained nuclear emulsion with several 10 nm silver halide crystals can detect submicron tracks. This detector is expected to be worked as dark matter detector with directional sensitive. Now, nuclear emulsion became possible to be produced at Nagoya University, and extreme fine grained nuclear emulsion with 20 nm diameter was produced. Using this emulsion and new reading out technique with expansion technique, for optical selection and X-ray microscopy, recoiled tracks induced by dark matter can be detected automatically. Then, readout efficiency is larger than 80% at 120 nm, and angular resolution for final confirmation with X-ray microscopy is 20°. In addition, we started to construct the R and D underground facility in Gran Sasso.

Water-Resistant Material from Recovered Fibers and Acrylic Emulsion Terpolymer

Directory of Open Access Journals (Sweden)

Fushan Chen

2014-01-01

Full Text Available Styrene (SM, methyl methacrylate (MMA, and butyl acrylate (BA were used to synthesize a polyacrylic emulsion by core-shell emulsion polymerization. The solid content of the emulsion reached 40% using reasonable reactive emulsifier contents and feeding modes. Then, the emulsion and a fiber were dispersed, coated, and dried together. Finally, fiber-based water-resistant material was successfully fabricated. The experimental results showed that under the conditions of a monomer mass ratio of 1:1:1 and a mass ratio of polyacrylic emulsion to fiber of 2:1, the Cobb value of the material reached 5.0 g/m2. The tensile strength, elongation, and breaking length were 7.4225 kN/m, 1.0%, and 11.706 km, respectively. Using scanning electron microscopy (SEM to analyze the surface morphology and internal structure of products, the reasons for the high water resistance of fiber-based material was due to the bonding and filling effects of the polyacrylic emulsion on the fibers. For tightly bound fibers, the porous structures formed in fiber-based boards were reduced. On the other hand, the polyacrylic emulsion filled the gaps between fibers. This filling effect led to a continuous structure, and the water resistance of the material was further enhanced.

Method validation and stability study of quercetin in topical emulsions

Directory of Open Access Journals (Sweden)

Rúbia Casagrande

2009-01-01

Full Text Available This study validated a high performance liquid chromatography (HPLC method for the quantitative evaluation of quercetin in topical emulsions. The method was linear within 0.05 - 200 μg/mL range with a correlation coefficient of 0.9997, and without interference in the quercetin peak. The detection and quantitation limits were 18 and 29 ng/mL, respectively. The intra- and inter-assay precisions presented R.S.D. values lower than 2%. An average of 93% and 94% of quercetin was recovered for non-ionic and anionic emulsions, respectively. The raw material and anionic emulsion, but not non-ionic emulsion, were stable in all storage conditions for one year. The method reported is a fast and reliable HPLC technique useful for quercetin determination in topical emulsions.

Formulation, Characterization and Properties of Hemp Seed Oil and Its Emulsions

Directory of Open Access Journals (Sweden)

Veronika Mikulcová

2017-04-01

Full Text Available The formulation, characterization, and anticipated antibacterial properties of hemp seed oil and its emulsions were investigated. The oil obtained from the seeds of Cannabis sativa L. in refined and unrefined form was characterized using iodine, saponification, acid values, and gas chromatography, and was employed for the preparation of stable oil-in-water emulsions. The emulsions were prepared using pairs of non-ionic surfactants (Tween, Span. The effects of the emulsification method (spontaneous emulsification vs. high-intensity stirring, hydrophilic lipophilic balance (HLB, type and concentration of surfactant, and oil type on the size and distribution of the emulsion particles were investigated. It was found that the ability to form stable emulsions with small, initial particle sizes is primarily dependent on the given method of preparation and the HLB value. The most efficient method of emulsification that afforded the best emulsions with the smallest particles (151 ± 1 nm comprised the high-energy method, and emulsions stable over the long-term were observed at HBL 9 with 10 wt % concentration of surfactants. Under high-intensity emulsification, refined and unrefined oils performed similarly. The oils as well as their emulsions were tested against the growth of selected bacteria using the disk diffusion and broth microdilution methods. The antibacterial effect of hemp seed oil was documented against Micrococcus luteus and Staphylococcus aureus subsp. aureus. The formulated emulsions did not exhibit the antibacterial activity that had been anticipated.

Phase behaviour and microstructure of the micro-emulsions composed of cholinium-based ionic liquid, Triton X-100 and water

International Nuclear Information System (INIS)

Pei, Yuanchao; Huang, Yanjie; Li, Lin; Wang, Jianji

2014-01-01

Highlights: • The microemulsions composed of cholinium-based ionic liquid, Triton X-100 and water have been prepared and characterised. • Ternary phase diagrams of the microemulsions have been established at T = 298.15 K. • The microemulsions exhibit IL-in-water, bicontinuous and water-in-IL microstructures. • Droplets with the size smaller than 20 nm are formed in these IL-based microemulsions. - Abstract: In this paper, micro-emulsions composed of cholinium-based ionic liquids (ILs), octylphenol ethoxylate (Triton X-100) and water were prepared. These ternary systems were found to be stable over 12 months at room temperature. Their phase behaviour was investigated by using cloud titrations, and their microstructures were characterised by means of cyclic voltammetry and electrical conductance measurements at T = 298.15 K. It was shown that the micro-emulsions exhibited IL-in-water, bi-continuous and water-in-IL microstructures. Dynamic light scattering data suggest that Triton X-100 forms micelles in water, which were swelled by the ILs added. Droplets with the size about 20 nm were formed in these IL-based micro-emulsions, and the droplet size increased with the increase of the IL concentrations. These IL-based micro-emulsions may have potential in drug delivery, chemical reactions and nanomaterial preparation as a new type of nanoreactors

Effects of Partial Beef Fat Replacement with Gelled Emulsion on Functional and Quality Properties of Model System Meat Emulsions.

Science.gov (United States)

Serdaroğlu, Meltem; Nacak, Berker; Karabıyıkoğlu, Merve; Keser, Gökçen

2016-01-01

The objective of this study was to investigate the effects of partial beef fat replacement (0, 30, 50, 100%) with gelled emulsion (GE) prepared with olive oil on functional and quality properties of model system meat emulsion (MSME). GE consisted of inulin and gelatin as gelling agent and characteristics of gelled and model system meat emulsions were investigated. GE showed good initial stability against centrifugation forces and thermal stability at different temperatures. GE addition decreased the pH with respect to increase in GE concentration. Addition of GE increased lightness and yellowness but reduced redness compared to control samples. The results of the study showed that partial replacement of beef fat with GE could be used for improving cooking yield without negative effects on water holding capacity and emulsion stability compared to C samples when replacement level is up to 50%. The presence of GE significantly affected textural behaviors of samples ( p <0.05). In conclusion, our study showed that GE have promising impacts on developing healthier meat product formulations besides improving technological characteristics.

Preparation of Lipid Nano emulsions Incorporating Curcumin for Cancer Therapy

International Nuclear Information System (INIS)

Anuchapreeda, S.; Anuchapreeda, S.; Fukumori, Y.; Ichikawa, H.; Okonogi, S.

2012-01-01

The aim of this study was to develop a new formulation of a curcumin lipid nano emulsion having the smallest particle size, the highest loading, and a good physical stability for cancer chemotherapy. Curcumin lipid nano emulsions were prepared by a modified thin-film hydration method followed by sonication. Soybean oil, hydrogenated L-α-phosphatidylcholine from egg yolk, and co surfactants were used to formulate the emulsions. The resultant nano emulsions showed mean particle diameter of 47-55 nm, could incorporate 23-28 mg curcumin per 30 mL, and were stable in particle size for 60 days at 4 degree C. The cytotoxicity studies of curucumin solution and curcumin-loaded nano emulsion using B16F10 and leukemic cell lines showed IC 50 values ranging from 3.5 to 30.1 and 22.2 to 53.7μM, respectively. These results demonstrated the successful incorporation of curcumin into lipid nano emulsion particles with small particle size, high loading capacity, good physical stability, and preserved cytotoxicity

Multi-responsive ionic liquid emulsions stabilized by microgels

NARCIS (Netherlands)

Monteillet, H.; Workamp, M.; Li, X.; Schuur, Boelo; Kleijn, J.M.; Leermakers, F.; Sprakel, J.

2014-01-01

We present a complete toolbox to use responsive ionic liquid (IL) emulsions for extraction purposes. IL emulsions stabilized by responsive microgels are shown to allow rapid extraction and reversible breaking and re-emulsification. Moreover, by using a paramagnetic ionic liquid, droplets can be

Microfluidic production of multiple emulsions and functional microcapsules

NARCIS (Netherlands)

Lee, Tae Yong; Choi, Tae Min; Shim, Tae Soup; Frijns, Raoul A.M.; Kim, Shin Hyun

2016-01-01

Recent advances in microfluidics have enabled the controlled production of multiple-emulsion drops with onion-like topology. The multiple-emulsion drops possess an intrinsic core-shell geometry, which makes them useful as templates to create microcapsules with a solid membrane. High flexibility

Nuclear interactions of 400 GeV protons in emulsion

International Nuclear Information System (INIS)

Otterlund, I.; Stenlund, E.; Andersson, B.; Nilsson, G.; Adamovic, O.; Juric, M.; Areti, H.; Hebert, C.J.D.; Hebert, J.; Baumann, G.; Devienne, R.; Bolta, J.M.; Sanchis, M.A.; Bravo, L.; Niembro, R.; Ruiz, A.; Villar, E.

1978-01-01

The authors report on 400 GeV proton-emulsion nuclei reactions and compare the results to hadron-nucleus reactions at smaller energies. In particular they present results on the emission of fast target protons (essentially grey track particles) and on their correlation with the number of collisions inside the nucleus, γ, with the number of charged evaporated particles (essentially black track particles) and with the number of pions produced (essentially shower particles). It is observed that the main features of the 200-400 GeV data are very similar. However, it is found that the mean shower-particle multiplicity at 400 GeV is essentially higher than expected from the simple independent particle model prediction = [1+0.5( )-1)]. The shower particle multiplicities do not seem to follow a target mass dependence of the form =nsub(ch)>Asup(α) with α=0.14 or α=0.19 as has been suggested in the literature. The pseudo-rapidity distribution shows limiting target and projectile fragmentation. The shower-particle multiplicity in the 'central region' increases linearly with but faster than 0.5(γ) times the corresponding multiplicity in pp reactions. (Auth.)

Oxidative Stability and Shelf Life of Food Emulsions

DEFF Research Database (Denmark)

Jacobsen, Charlotte

2016-01-01

Lipid oxidation and antioxidant effects in food emulsions are influenced by many different factors, such as the composition of the aqueous phase and interface, the partitioning of the antioxidants between the different phases of the emulsion system, the antioxidant properties, and others. This ch...

Functional copolymer/organo-MMT nanoarchitectures. VI. Synthesis and characterization of novel nanocomposites by interlamellar controlled/living radical copolymerization via preintercalated RAFT-agent/organoclay complexes.

Science.gov (United States)

Rzayev, Zakir M O; Söylemez, A Ernur

2011-04-01

We have developed a new approach for the synthesis of polymer nanocomposites using a bifunctional reversible addition-fragmentation chain transfer (RAFT) agent, two types of organo-montmorillonites, such as a non-reactive dimethyldodecyl ammonium (DMDA)-MMT and a reactive octadecylamine (ODA)-MMT organoclays, and a radical initiator. The method includes the following stages: (1) synthesis of RAFT intercalated O-MMTs by a physical or chemical interaction of the RAFT agent having two pendant carboxylic groups [S,S-bis(alpha,alpha'-dimethyl-alpha"-acetic acid)trithiocarbonate] with surface alkyl amines of O-MMT containing tertiary ammonium cation or primary amine groups through strong H-bonding and complexing/amidization reactions, respectively, and (2) utilization of these well-dispersed and intercalated RAFT ... O-MMT complexes and their amide derivatives as new modified RAFT agents in radical-initiated interlamellar controlled/living copolymerization of itaconic acid (IA)-n-butylmethacrylate (BMA) monomer pair. The structure and compositions of the synthesized RAFT ... O-MMT complexes and functional copolymer/O-MMT hybrids were confirmed by FTIR, XRD, thermal (DSC-TGA), SEM and TEM morphology analyses. It was demonstrated that the degree of interaction/exfoliation, morphology and thermal behavior of nanocomposites significantly depended on the type of organoclay and in situ interaction, as well as on the content of flexible butyl-ester linkages as a internal plasticizer. The results of the comparative analysis of the nanocomposites structure-composition-property relations show that the functional copolymer-organoclay hybrids prepared with reactive RAFT ... ODA-MMT complex and containing a combination of partially intercalated and predominantly exfoliated nano-structures exhibit relatively higher thermal stability and fine dispersed morphology. These effects were explained by in situ interfacial chemical reactions through amidization of RAFT with surface alkyl amine

Superhydrophobic cellulose-based bionanocomposite films from Pickering emulsions

Science.gov (United States)

Bayer, Ilker S.; Steele, Adam; Martorana, Philip J.; Loth, Eric; Miller, Lance

2009-04-01

Inherently superhydrophobic and flexible cellulose-based bionanocomposites were fabricated from solid stabilized (Pickering) emulsions. Emulsions were formed by dispersing cyclosiloxanes in water stabilized by layered silicate particles and were subsequently modified by blending into a zinc oxide nanofluid. The polymer matrix was a blend of cellulose nitrate and fluoroacrylic polymer (Zonyl 8740) precompatibilized in solution. Coatings were spray cast onto aluminum substrates from polymer blends dispersed in modified Pickering emulsions. No postsurface treatment was required to induce superhydrophobicity. Effect of antiseptic additives on bionanocomposite superhydrophobicity is also discussed. Replacing cellulose nitrate with commercial liquid bandage solutions produced identical superhydrophobic coatings.

Ultra-High Pressure Homogenization enhances physicochemical properties of soy protein isolate-stabilized emulsions.

Science.gov (United States)

Fernández-Ávila, C; Escriu, R; Trujillo, A J

2015-09-01

The effect of Ultra-High Pressure Homogenization (UHPH, 100-300MPa) on the physicochemical properties of oil-in-water emulsions prepared with 4.0% (w/v) of soy protein isolate (SPI) and soybean oil (10 and 20%, v/v) was studied and compared to emulsions treated by conventional homogenization (CH, 15MPa). CH emulsions were prepared with non-heated and heated (95°C for 15min) SPI dispersions. Emulsions were characterized by particle size determination with laser diffraction, rheological properties using a rotational rheometer by applying measurements of flow curve and by transmission electron microscopy. The variation on particle size and creaming was assessed by Turbiscan® analysis, and visual observation of the emulsions was also carried out. UHPH emulsions showed much smaller d 3.2 values and greater physical stability than CH emulsions. The thermal treatment of SPI prior CH process did not improve physical stability properties. In addition, emulsions containing 20% of oil exhibited greater physical stability compared to emulsions containing 10% of oil. Particularly, UHPH emulsions treated at 100 and 200MPa with 20% of oil were the most stable due to low particle size values (d 3.2 and Span), greater viscosity and partial protein denaturation. These results address the physical stability improvement of protein isolate-stabilized emulsions by using the emerging UHPH technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

Synthesis of metallic nanoshells on porphyrin-stabilized emulsions

Science.gov (United States)

Wang, Haorong [Albuquerque, NM; Song, Yujiang [Albuquerque, NM; Shelnutt, John A [Tijeras, NM; Medforth, Craig J [Winters, CA

2011-12-13

Metal nanostructures formed by photocatalytic interfacial synthesis using a porphyrin-stabilized emulsion template and the method for making the nanostructures. Catalyst-seeded emulsion droplets are employed as templates for hollow-nanoshell growth. The hollow metal nanospheres may be formed with or without inclusions of other materials.

Preparation of spherical fine particulate pigments within water-in-oil emulsions and their properties. (II). ; Formation mechanism and characteristic of spherical fine particulate pigment of tartrazine. W/O emulsion wo mochiita kyujo biryushi ganryo no chosei to seishitsu(dai 2 ho). ; Kiiro 4 go kyujo biryushi ganryo no seisei kiko to tokusei

Energy Technology Data Exchange (ETDEWEB)

Imai, T.; Iwano, K.; Hotta, H.; Takano, S.; Tsutsumi, H. (Kao Corporation, Tokyo (Japan))

1991-12-20

The previous report explained that an excellent spherical particulate pigment with a grain size of 0.5 mm or less can be obtained by preparing multinuclear aluminum lakes from acidic dyes and multinuclear aluminum salt using water droplets in a W/O emulsion as reaction fields. This paper describes preparing pigments varying the charging concentrations of the pigments in a W/O emulsion and the droplet particle size to discuss the mechanism of forming the pigments. As a result, it was found that the particle sizes in the produced pigments have a clear correlation with the charging concentrations of the pigments and the droplet particle sizes in the W/O emulsion. A pigment produced in the W/O emulsion forms only in its own droplets, and reflects its particle sizes. Films dispersed with pigments having different particle sizes were prepared to discuss their tinting abilities, whereas it was clarified that the smaller the particle size, the higher the tinting ability and the higher saturation in colored paint films. 6 refs., 9 figs., 3 tabs.

Fabrication, Rheology and Antioxidant Activity of Palm Esters-based Emulsions Loaded with Tocotrienol

Directory of Open Access Journals (Sweden)

S.H NG

2014-06-01

The yield stress of the emulsions increased with increasing acoustic amplitudes. The viscoelasticity of the emulsions were enhanced by the increase in the oil and surfactant concentrations. The emulsions with higher oil phase concentration [30% (w/w] showed greater elasticity which implied strong dynamic rigidity of the emulsions. The cohesive energy increased significantly with surfactant concentration especially for the emulsions with 30% (w/w oil phase concentration. The palm oil esters emulsions containing tocotrienol gave higher Trolox equivalent antioxidant capacity values which implied higher antioxidant capability. The tocotrienol in emulsion with 30% (w/w dispersed phase showed that they were the most stable with longest shelf life and exhibited greater inhibitory effects on the ABTS".

Use of micro-emulsion technology for the directed evolution of antibodies.

Science.gov (United States)

Buhr, Diane L; Acca, Felicity E; Holland, Erika G; Johnson, Katie; Maksymiuk, Gail M; Vaill, Ada; Kay, Brian K; Weitz, David A; Weiner, Michael P; Kiss, Margaret M

2012-09-01

Affinity reagents, such as antibodies, are needed to study protein expression patterns, sub-cellular localization, and post-translational modifications in complex mixtures and tissues. Phage Emulsion, Secretion, and Capture (ESCape) is a novel micro-emulsion technology that utilizes water-in-oil (W/O) emulsions for the identification and isolation of cells secreting phage particles that display desirable antibodies. Using this method, a large library of antibody-displaying phage will bind to beads in individual compartments. Rather than using biopanning on a large mixed population, phage micro-emulsion technology allows us to individually query clonal populations of amplified phage against the antigen. The use of emulsions to generate microdroplets has the promise of accelerating phage selection experiments by permitting fine discrimination of kinetic parameters for binding to targets. In this study, we demonstrate the ability of phage micro-emulsion technology to distinguish two scFvs with a 300-fold difference in binding affinities (100nM and 300pM, respectively). In addition, we describe the application of phage micro-emulsion technology for the selection of scFvs that are resistant to elevated temperatures. Copyright © 2012. Published by Elsevier Inc.

Impact of Protein Gel Porosity on the Digestion of Lipid Emulsions.

Science.gov (United States)

Sarkar, Anwesha; Juan, Jean-Marc; Kolodziejczyk, Eric; Acquistapace, Simone; Donato-Capel, Laurence; Wooster, Tim J

2015-10-14

The present study sought to understand how the microstructure of protein gels impacts lipolysis of gelled emulsions. The selected system consisted of an oil-in-water (o/w) emulsion embedded within gelatin gels. The gelatin-gelled emulsions consisted of a discontinuous network of aggregated emulsion droplets (mesoscale), dispersed within a continuous network of gelatin (microscale). The viscoelastic properties of the gelled emulsions were dominated by the rheological behavior of the gelatin, suggesting a gelatin continuous microstructure rather than a bicontinuous gel. A direct relationship between the speed of fat digestion and gel average mesh size was found, indicating that the digestion of fat within gelatin-gelled emulsions is controlled by the ability of the gel's microstructure to slow lipase diffusion to the interface of fat droplets. Digestion of fat was facilitated by gradual breakdown of the gelatin network, which mainly occurred via surface erosion catalyzed by proteases. Overall, this work has demonstrated that the lipolysis kinetics of gelled emulsions is driven by the microstructure of protein gels; this knowledge is key for the future development of microstructures to control fat digestion and/or the delivery of nutrients to different parts of the gastrointestinal tract.

Swelling and thermodynamic studies of temperature responsive 2-hydroxyethyl methacrylate/itaconic acid copolymeric hydrogels prepared via gamma radiation

International Nuclear Information System (INIS)

Tomic, Simonida L.J.; Micic, Maja M.; Filipovic, Jovanka M.; Suljovrujic, Edin H.

2007-01-01

The copolymeric hydrogels based on 2-hydroxyethyl methacrylate (HEMA) and itaconic acid (IA) were synthesized by gamma radiation induced radical polymerization. Swelling and thermodynamic properties of PHEMA and copolymeric P(HEMA/IA) hydrogels with different IA contents (2, 3.5 and 5 mol%) were studied in a wide pH and temperature range. Initial studies of so-prepared hydrogels show interesting pH and temperature sensitivity in swelling and drug release behavior. Special attention was devoted to temperature investigations around physiological temperature (37 deg. C), where small changes in temperature significantly influence swelling and drug release of these hydrogels. Due to maximum swelling of hydrogels around 40 deg. C, the P(HEMA/IA) hydrogel containing 5 mol% of IA without and with drug-antibiotic (gentamicin) were investigated at pH 7.40 and in the temperature range 25-42 deg. C, in order to evaluate their potential for medical applications

Encapsulation of Polymethoxyflavones in Citrus Oil Emulsion-Based Delivery Systems.

Science.gov (United States)

Yang, Ying; Zhao, Chengying; Chen, Jingjing; Tian, Guifang; McClements, David Julian; Xiao, Hang; Zheng, Jinkai

2017-03-01

The purpose of this work was to elucidate the effects of citrus oil type on polymethoxyflavone (PMF) solubility and on the physicochemical properties of PMF-loaded emulsion-based delivery systems. Citrus oils were extracted from mandarin, orange, sweet orange, and bergamot. The major constituents were determined by GC/MS: sweet orange oil (97.4% d-limonene); mandarin oil (72.4% d-limonene); orange oil (67.2% d-limonene); and bergamot oil (34.6% linalyl acetate and 25.3% d-limonene). PMF-loaded emulsions were fabricated using 10% oil phase (containing 0.1% w/v nobiletin or tangeretin) and 90% aqueous phase (containing 1% w/v Tween 80) using high-pressure homogenization. Delivery systems prepared using mandarin oil had the largest mean droplet diameters (386 or 400 nm), followed by orange oil (338 or 390 nm), bergamot oil (129 or 133 nm), and sweet orange oil (122 or 126 nm) for nobiletin- or tangeretin-loaded emulsions, respectively. The optical clarity of the emulsions increased with decreasing droplet size due to reduced light scattering. The viscosities of the emulsions (with or without PMFs) were similar (1.3 to 1.4 mPa·s), despite appreciable differences in oil phase viscosity. The loading capacity and encapsulation efficiency of the emulsions depended on carrier oil type, with bergamot oil giving the highest loading capacity. In summary, differences in the composition and physical characteristics of citrus oils led to PMF-loaded emulsions with different encapsulation and physicochemical characteristics. These results will facilitate the rational design of emulsion-based delivery systems for encapsulation of PMFs and other nutraceuticals in functional foods and beverages.

Potassium diperiodatocuprate-mediated preparation of poly(methyl methacrylate/organo-montmorillonite composites via in situ grafting copolymerization

Directory of Open Access Journals (Sweden)

2008-09-01

Full Text Available In this study, potassium diperiodatocuprate (Cu3+ was selected as an initiator to prepare poly(methyl methacrylate/organo-montmorillonite composites (OMMT-g-PMMA by in situ graft copolymerization. Three synthetic parameters were systematically evaluated as a function of the temperature, the concentration of initiator, pH and the ratio of MMA to OMMT. It was found that Cu3+ was a highly efficient initiator for the preparation of OMMT-g-PMMA i.e., monomer conversion and grafting efficiency were as higher as 95%. The X-ray diffraction measurement showed the intercalation of PMMA chains into OMMT layers on base of an increasing basal spacing after polymerization. FTIR analysis also suggested that the PMMA chains were effectively grafted onto OMMT substrate. The enhanced thermal stabilities of OMMT-g-PMMA composites were confirmed by the thermal gravimetric analysis (TGA. Finally, a single-electron-transfer mechanism was proposed to illustrate the formation of radicals and the preparation process of OMMT-g-PMMA composites. Cu3+ can be used as an effective and practical initiator in preparing the organic/inorganic composite due to its high grafting efficiency and the milder reaction condition.

Concanavalin-A conjugated fine-multiple emulsion loaded with 6-mercaptopurine.

Science.gov (United States)

Khopade, A J; Jain, N K

2000-01-01

Fine-multiple (water-in-oil-in-water) emulsions were prepared by two-step emulsification using sonication. They were coated with concanavalin-A (Con-A) by three methods. The one involving covalent coupling of Con-A to the multiple emulsion incorporated anchor was better compared with lipid derivatized Con-A anchoring or the glutaraldehyde-based cross-linking method, as shown by the faster rate of dextran-induced aggregation. The selected multiple emulsions were characterized by physical properties such as droplet size, encapsulation efficiency, and zeta potential. Stability parameters such as droplet size, creaming, leakage, and aggregation as a function of relative turbidity were monitored over a 1-month period, which revealed good stability of the formulations. The release profile of 6-mercaptopurine followed zero-order kinetics. Pharmacokinetic studies showed an increase in half-life and bioavailability from multiple emulsion formulations administered intravenously. There was prolonged retention of drug in various tissues of rats when treated with Con-A-coated multiple emulsion as compared with uncoated one. Our study demonstrates the suitability of fine-multiple emulsion for intravenous administration and the potential for prolonged retention of drugs and targeting in biological systems.

Oil-in-water emulsions flow through constricted micro-capillarities

Energy Technology Data Exchange (ETDEWEB)

Castillo, Oswaldo Robles; Carvalho, Marcio da Silveira [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil). Dept. of Mechanical Engineering

2010-07-01

The effect of the oil concentration and the drop size distribution on the characteristics of the flow of an emulsion through a constricted capillary was experimentally analyzed and quantified by the ratio of the pressure drop of the continuous phase flow to the pressure drop of the emulsion flow, at the same flow rate. The results confirm that the ratio between the capillary constriction diameter and the oil drop size is one of the most important parameters for this flow. For large oil drop size emulsions, the deformation of the drop as it flows through the constriction leads to a high extra pressure drop at low capillary numbers. For small oil drop size emulsions, the extra pressure drop is a function of the viscosity ratio and the disperse phase concentration. (author)

21 CFR 524.802 - Enrofloxacin, silver sulfadiazine emulsion.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Enrofloxacin, silver sulfadiazine emulsion. 524... ANIMAL DRUGS § 524.802 Enrofloxacin, silver sulfadiazine emulsion. (a) Specifications. Each milliliter contains 5 milligrams (mg) enrofloxacin and 10 mg silver sulfadiazine. (b) Sponsor. See No. 000859 in § 510...

Efficiency of emulsifier-free emulsions and emulsions containing rapeseed lecithin as delivery systems for vectorization and release of coenzyme Q10: physico-chemical properties and in vitro evaluation.

Science.gov (United States)

Kaci, M; Arab-Tehrany, E; Dostert, G; Desjardins, I; Velot, E; Desobry, S

2016-11-01

To improve the encapsulation and release of coenzyme Q10 (CoQ10), emulsifier-free-emulsions were developed with a new emulsification process using high-frequency ultrasound (HFU) at 1.7MHz. Nano-emulsions containing CoQ10 were prepared with or without rapeseed lecithin as an emulsifier. The emulsions prepared with HFU were compared with an emulsion of CoQ10 containing emulsifier prepared with the same emulsification technique as well as with emulsions prepared with low-frequency ultrasound coupled with high-pressure homogenization (LFU+HPH). The physico-chemical properties of the emulsions were determined by average droplet size measurement with nano-droplet tracking analysis, droplet surface charge with ζ potential measurement, surface tension and rheological behaviour. Emulsions made by LFU+HPH with an emulsifier showed lower droplet sizes due to cavitation generated by the HFU process. Surface tension results showed that there was no significant difference between emulsions containing lecithin emulsifier regardless of the preparation process or the inclusion of CoQ10. In vitro biocompatibility tests were performed on human mesenchymal stem cells in order to show the cytotoxicity of various formulations and the efficiency of CoQ10-loaded emulsions. In vitro tests proved that the vectors were not toxic. Furthermore, CoQ10 facilitated a high rate of cell proliferation and metabolic activity especially when in an emulsifier-free formulation. Copyright © 2016 Elsevier B.V. All rights reserved.

A novel automatic film changer for high-speed analysis of nuclear emulsions

International Nuclear Information System (INIS)

Borer, K.; Damet, J.; Hess, M.; Kreslo, I.; Moser, U.; Pretzl, K.; Savvinov, N.; Schuetz, H.-U.; Waelchli, T.; Weber, M.

2006-01-01

This paper describes the recent development of a novel automatic computer-controlled manipulator for emulsion sheet placement and removal at the microscope object table (also called stage). The manipulator is designed for mass scanning of emulsions for the OPERA neutrino oscillation experiment and provides emulsion changing time shorter than 30s with an emulsion sheet positioning accuracy as good as 20μm RMS

Spreading of oil from protein stabilised emulsions at air/water interfaces

NARCIS (Netherlands)

Schokker, E.P.; Bos, M.A.; Kuijpers, A.J.; Wijnen, M.E.; Walstra, P.

2002-01-01

Spreading of a drop of an emulsion made with milk proteins on air/water interfaces was studied. From an unheated emulsion, all oil molecules could spread onto the air/water interface, indicating that the protein layers around the oil globules in the emulsion droplet were not coherent enough to

STUDY REGARDING THE DESTABILIZATION OF STABLE EMULSIONS FROM SUPLAC AREA

Directory of Open Access Journals (Sweden)

IULIANA VERONICA GHEŢIU

2016-12-01

Full Text Available Emulsions from the wells in the Suplac area create great difficulties in removing water due to their specifications. A complex study was conducted in order to eliminate water from emulsions using alkaline-surfactants. The choice of surfactant was made after the chromatographic SARA analysis of emulsions and the determination of their physical properties: density, viscosity, organic acidity. The samples were taken from two wells in the Suplac area. In the case of samples from A well the variation of density is 907 - 955 kg·m-3 for crude oil and 928 - 970 kg·m-3 for emulsion, while the rheological behavior of the emulsion varies between 0.680 to 0.995 Pa·s at a temperature of 25 °C and between 0.049 to 0.328 Pa·s at a temperature of 80 °C. For samples from B well the variation of density is 855 - 905 kg·m-3 for crude oil and 939 - 970 kg·m-3 for emulsion, while the rheological behavior of the emulsion varies between 0.149 to 0.797 Pa·s at a temperature of 25 °C and between 0.014 to 0.397 Pa·s at a temperature of 80 °C. The justification for choosing R - DP surfactant like reagent was based on laboratory tests which showed a maximum efficiency at 80 °C (95.69 for B and 98.75 % for A.

Organic Based Glutinous Corn (Zea maize Supplemented With Seaweeds Emulsion

Directory of Open Access Journals (Sweden)

Jayrome S. Butay

2017-11-01

Full Text Available The study was therefore design to generate scientific information that are vital for organic farming advocates as it uses natural organic farm inputs in the production of corn. It was conducted because of the insurmountable rising cost of inorganic fertilizers perspective the farmers have to look for alternative measures to sustain the profitability of their farming business by evaluating the efficacy of seaweeds emulsion (Carrageenan as nutrient supplement to organic fertilizer on glutinous corn production, a study was conducted at the Cagayan State University – Lal-lo, Cagayan from July 17 to September 25, 2016with the following treatments: T1- Control, T2 – 3 tons Organic Fertilizer, T3 - 1.5 liters Seaweeds Emulsion ha-1 , T4 - 3 liters Seaweeds Emulsion ha-1 , T5 - 4.5 liters Seaweeds Emulsion ha-1 and T6 - 6 liters Seaweeds Emulsion ha-1 arranged in Randomized Complete Block Design with three replications. The treatments have no significant effect on plant height. Application of seaweed emulsion affected the grain development as manifested by longer and heavier corn ear. Higher rates (3-6 li ha-1 proved to more efficient as indicated by the bigger ear, highest yield and ROI of 909.62 percent. The study revealed that 3 tons Organic Fertilizer with liters of seaweed emulsion improved glutinous corn production. Further study is recommended to validate the result and come up with a more reliable conclusion.

Modified montmorillonite clay microparticles for stable oil-in-seawater emulsions.

Science.gov (United States)

Dong, Jiannan; Worthen, Andrew J; Foster, Lynn M; Chen, Yunshen; Cornell, Kevin A; Bryant, Steven L; Truskett, Thomas M; Bielawski, Christopher W; Johnston, Keith P

2014-07-23

Environmentally benign clay particles are of great interest for the stabilization of Pickering emulsions. Dodecane-in-synthetic seawater (SSW) emulsions formed with montmorillonite (MMT) clay microparticles modified with bis(2-hydroxyethyl)oleylamine were stable against coalescence, even at clay concentrations down to 0.1% w/v. Remarkably, as little as 0.001% w/v surfactant lowered the hydrophilicity of the clay to a sufficient level for stabilization of oil-in-SSW emulsions. The favorable effect of SSW on droplet size reduction and emulsion stability enhancement is hypothesized to be due to reduced electrostatic repulsion between adsorbed clay particles and a consequent increase in the continuous phase (an aqueous clay suspension) viscosity. Water/oil (W/O) emulsions were inverted to O/W either by decreasing the mass ratio of surfactant-to-clay (transitional inversion) or by increasing the water volume fraction (catastrophic inversion). For both types of emulsions, coalescence was minimal and the sedimentation or creaming was highly correlated with the droplet size. For catastrophic inversions, the droplet size of the emulsions was smaller in the case of the preferred curvature. Suspensions of concentrated clay in oil dispersions in the presence of surfactant were stable against settling. The mass transfer pathways during emulsification of oil containing the clay particles were analyzed on the droplet size/stability phase diagrams to provide insight for the design of dispersant systems for remediating surface and subsurface oceanic oil spills.

Separation kinetics of an oil-in-water emulsion under enhanced gravity

NARCIS (Netherlands)

Krebs, T.; Schroën, C.G.P.H.; Boom, R.M.

2012-01-01

The breakup of crude oil emulsions to produce clean oil and water phases is an important task in crude oil processing. We have investigated the demulsification kinetics of a model oil-in-water emulsion in a centrifugal field to mimic the forces acting on emulsion droplets in oil/water separators

Synthesis and purification of oxide nanoparticle dispersions by modified emulsion precipitation.

Science.gov (United States)

Shi, Jingyu; Verweij, Henk

2005-06-07

ZrO2 and Fe2O3 precursor nanoparticles are synthesized, well-dispersed in decane, via a modified emulsion precipitation (MEP) method. This method starts with preparing two thermostable water-in-oil (w/o) emulsions with nonylphenol tetra(ethylene glycol) ether (Arkopal-40) as the main surfactant, didodecyldimethylammonium bromide (DiDAB) as the cosurfactant, decane as the continuous oil phase, and either a metal salt solution or a hexamethylenetetramine (HMTA) precipitation agent solution as the dispersed water phase. After mixing of the two emulsions, individual precursor particles are formed by precipitation in the confinement of the aqueous solution droplets. Excess water is removed by azeotropic distillation, and steric stabilization of the particles in the remaining oil medium is achieved with poly(octadecyl methacrylate) (PODMA), initially present dissolved in the oil phase. A purification process is conducted to remove the precipitation reaction byproduct and excess surfactants from the nanoparticle dispersions. Transmission electron microscopy (TEM) characterization shows that the ZrO2 and Fe2O3 precursor nanoparticles are both non-agglomerated, spherical, and have a narrow particle size distribution, centered at 4 nm in diameter. The precipitation from the dispersion of byproduct NH4Cl after water removal, and insoluble surfactant DiDAB after dilution with pure decane, is confirmed by X-ray diffraction (XRD). NMR results show that most of the oil-soluble surfactant Arkopal-40 can be removed from the dispersion by a 3x repeated dead-end pressure filtration process. It is shown that, after purification, the nanoparticle dispersions can be used for the preparation of homogeneous nanostructured coatings. The purification procedure as discussed provides guidelines for up-scaling the process and reuse of emulsifiers.

Antioxidant Behavior of Olive Phenolics in Oil-in-Water Emulsions.

Science.gov (United States)

Paradiso, Vito Michele; Di Mattia, Carla; Giarnetti, Mariagrazia; Chiarini, Marco; Andrich, Lucia; Caponio, Francesco

2016-07-27

The effect of the surrounding molecular environment (β-lactoglobulin as an emulsion stabilizer and maltodextrin as a viscosity modifier) on the antioxidant activity of three olive oil phenolic compounds (PCs) in olive oil-in-water emulsions was investigated. Oxidation potential, phenolic partitioning, and radical quenching capacity were assessed in solution and in emulsion for oleuropein, hydroxytyrosol, and tyrosol; the influence of β-lactoglobulin and maltodextrin concentration was also evaluated. Finally, the observed properties were related to the oxidative stability of the emulsions containing the PCs to explain their behavior. The order hydroxytyrosol > oleuropein > tyrosol was observed among the antioxidants for both oxidation potential and radical quenching activity. Radical quenching capacity in emulsion and anodic potential were complementary indices of antioxidant effectiveness. As the intrinsic susceptibility of an antioxidant to oxidation expressed by its anodic potential decreased, the environmental conditions (molecular interactions and changes in continuous phase viscosity) played a major role in the antioxidant effectiveness in preventing hydroperoxide decomposition.

Influence of processing parameters on morphology of polymethoxyflavone in emulsions.

Science.gov (United States)

Ting, Yuwen; Li, Colin C; Wang, Yin; Ho, Chi-Tang; Huang, Qingrong

2015-01-21

Polymethoxyflavones (PMFs) are groups of compounds isolated from citrus peels that have been documented with wide arrays of health-promoting bioactivities. Because of their hydrophobic structure and high melting point, crystallized PMFs usually have poor systemic bioavailability when consumed orally. To improve the oral efficiency of PMFs, a viscoelastic emulsion system was formulated. Because of the crystalline nature, the inclusion of PMFs into the emulsion system faces great challenges in having sufficient loading capacity and stabilities. In this study, the process of optimizing the quality of emulsion-based formulation intended for PMF oral delivery was systematically studied. With alteration of the PMF loading concentration, processing temperature, and pressure, the emulsion with the desired droplet and crystal size can be effectively fabricated. Moreover, storage temperatures significantly influenced the stability of the crystal-containing emulsion system. The results from this study are a good illustration of system optimization and serve as a great reference for future formulation design of other hydrophobic crystalline compounds.

Dual function of tributyrin emulsion: solubilization and enhancement of anticancer effect of celecoxib.

Science.gov (United States)

Kang, Sung Nam; Hong, Soon-Seok; Lee, Mi-Kyung; Lim, Soo-Jeong

2012-05-30

Tributyrin, a triglyceride analogue of butyrate, can act as a prodrug of an anticancer agent butyrate after being cleaved by intracellular enzymes. We recently demonstrated that the emulsion containing tributyrin as an inner oil phase possesses a potent anticancer activity. Herein we sought to develop tributyrin emulsion as a carrier of celecoxib, a poorly-water soluble drug with anticancer activity. Combined treatment of human HCT116 colon cancer cells with free celecoxib plus tributyrin emulsion inhibited the cellular proliferation more effectively than that of each drug alone, suggesting the possibility of tributyrin emulsion as a potential celecoxib carrier. The mean droplet size of emulsions tended to increase as the tributyrin content in emulsion increases and the concentration of celecoxib loaded in emulsions was affected by tributyrin content and the initial amount of celecoxib, but not by the total amount of surfactant mixture. The concentration of celecoxib required to inhibit the growth of HCT116 and B16-F10 cancer cells by 50% was 2.6- and 3.1-fold lowered by loading celecoxib in tributyrin emulsions, compared with free celecoxib. These data suggest that the anticancer activity of celecoxib was enhanced by loading in tributyrin emulsions, probably due to the solubilization capacity and anticancer activity of tributyrin emulsion. Copyright © 2012 Elsevier B.V. All rights reserved.

Generation of colloidal granules and capsules from double emulsion drops

Science.gov (United States)

Hess, Kathryn S.

Assemblies of colloidal particles are extensively used in ceramic processing, pharmaceuticals, inks and coatings. In this project, the aim was to develop a new technique to fabricate monodispersed colloidal assemblies. The use of microfluidic devices and emulsion processing allows for the fabrication of complex materials that can be used in a variety of applications. A microfluidic device is used to create monodispersed water/oil/water (w/o/w) double emulsions with interior droplets of colloidal silica suspension ranging in size from tens to hundreds of microns. By tailoring the osmotic pressure using glycerol as a solute in the continuous and inner phases of the emulsion, we can control the final volume size of the monodispersed silica colloidal crystals that form in the inner droplets of the double emulsion. Modifying the ionic strength in the colloidal dispersion can be used to affect the particle-particle interactions and crystal formation of the final colloidal particle. This w/o/w technique has been used with other systems of metal oxide colloids and cellulose nanocrystals. Encapsulation of the colloidal suspension in a polymer shell for the generation of ceramic-polymer core-shell particles has also been developed. These core-shell particles have spawned new research in the field of locally resonant acoustic metamaterials. Systems and chemistries for creating cellulose hydrogels within the double emulsions have also been researched. Water in oil single emulsions and double emulsions have been used to create cellulose hydrogel spheres in the sub-100 micron diameter range. Oil/water/oil double emulsions allow us to create stable cellulose capsules. The addition of a second hydrogel polymer, such as acrylate or alginate, further strengthens the cellulose gel network and can also be processed into capsules and particles using the microfluidic device. This work could have promising applications in acoustic metamaterials, personal care products, pharmaceuticals

Water-in-oil emulsions results of formation studies and applicability to oil spill modelling

International Nuclear Information System (INIS)

Fingas, Merv; Fieldhouse, Ben; Mullin, Joe

1999-01-01

This paper summarises studies of water-in-oil emulsions, their stability, and modelling of their formation. Studies show that water-in-oil emulsions might be characterised into three categories (stable, mesostable and unstable). These categories were established by visual appearance, elasticity and viscosity difference. It was also shown that water content was not an important factor. A fourth category of water-in-oil exists, that of water entrainment, which is not an emulsion. Water-in-oil emulsions made from crude oils have different classes of stabilities as a result of the asphaltene and resin contents. The differences in the emulsion types are readily distinguished both by their rheological properties, and simply by appearance. The apparent viscosity of a stable emulsion at a shear rate of one reciprocal second, is at least three orders-of-magnitude greater than the starting oil. An unstable emulsion usually has a viscosity no more than one order-of-magnitude greater than that of the starting oil. A stable emulsion has a significant elasticity, whereas an unstable emulsion does not. Stable emulsions have sufficient asphaltenes (>∼7%) to establish films of these compounds around water droplets. Mesostable emulsions have insufficient asphaltenes to render them completely stable. Stability is achieved by visco-elastic retention of water and secondarily by the presence of asphaltene or resin films. Mesostable emulsions display apparent viscosities of about 80-600 times that of the starting oil and true viscosities of 20-200 times that of the starting oil. Mesostable emulsions have an asphaltene and resin content greater than 3%. Entrained water occurs when a viscous oil retains larger water droplets, but conditions are not suitable for the formation of an emulsion. Entrained water may have a viscosity that is similar or slightly greater (∼ 2-10 times) than the starting oil. It was found that emulsion formation occurs at a threshold energy, however this energy

Endocytosis of Corn Oil-Caseinate Emulsions In Vitro: Impacts of Droplet Sizes

Science.gov (United States)

Fan, Yuting; Yokoyama, Wally; Yi, Jiang

2017-01-01

The relative uptake and mechanisms of lipid-based emulsions of three different particle diameters by Caco-2 cells were studied. The corn oil-sodium caseinate emulsions showed little or no cytotoxicity even at 2 mg/mL protein concentration for any of the three droplet size emulsions. Confocal laser scanning microscopy (CLSM) of Nile red containing emulsions showed that the lipid-based emulsions were absorbed by Caco-2 cells. A negative correlation between the mean droplet size and cellular uptake was observed. There was a time-dependent and energy-dependent uptake as shown by incubation at different times and treatment with sodium azide a general inhibitor of active transport. The endocytosis of lipid-based emulsions was size-dependent. The internalization of nanoemulsion droplets into Caco-2 cells mainly occurred through clathrin- and caveolae/lipid raft-related pathways, while macropinocytosis route played the most important role for 556 nm emulsion endocytosis as shown by the use of specific pathway inhibitors. Permeability of the emulsion through the apical or basal routes also suggested that active transport may be the main route for lipid-based nanoemulsions. The results may assist in the design and application of lipid-based nanoemulsions in nutraceuticals and pharmaceuticals delivery. PMID:29072633

Endocytosis of Corn Oil-Caseinate Emulsions In Vitro: Impacts of Droplet Sizes

Directory of Open Access Journals (Sweden)

Yuting Fan

2017-10-01

Full Text Available The relative uptake and mechanisms of lipid-based emulsions of three different particle diameters by Caco-2 cells were studied. The corn oil-sodium caseinate emulsions showed little or no cytotoxicity even at 2 mg/mL protein concentration for any of the three droplet size emulsions. Confocal laser scanning microscopy (CLSM of Nile red containing emulsions showed that the lipid-based emulsions were absorbed by Caco-2 cells. A negative correlation between the mean droplet size and cellular uptake was observed. There was a time-dependent and energy-dependent uptake as shown by incubation at different times and treatment with sodium azide a general inhibitor of active transport. The endocytosis of lipid-based emulsions was size-dependent. The internalization of nanoemulsion droplets into Caco-2 cells mainly occurred through clathrin- and caveolae/lipid raft-related pathways, while macropinocytosis route played the most important role for 556 nm emulsion endocytosis as shown by the use of specific pathway inhibitors. Permeability of the emulsion through the apical or basal routes also suggested that active transport may be the main route for lipid-based nanoemulsions. The results may assist in the design and application of lipid-based nanoemulsions in nutraceuticals and pharmaceuticals delivery.

In Vitro and In Vivo Characterization of Biodegradable Reactive Isocyanate-Terminated Three-Armed- and Hyperbranched Block Copolymeric Tissue Adhesives

NARCIS (Netherlands)

Bochynska, Agnieszka I.; Hannink, Gerjon; Rongen, Jan J.; Grijpma, Dirk W.; Buma, Pieter

2017-01-01

Tissue adhesives are an attractive class of biomaterials, which can serve as a treatment for meniscus tears. In this study, physicochemical and adhesive properties of novel biodegradable three-armed- and hyperbranched block copolymeric adhesives are evaluated. Additionally, their degradation in

Cosmetic emulsion from virgin olive oil: Formulation and bio ...

African Journals Online (AJOL)

Cosmetic emulsion from virgin olive oil: Formulation and bio-physical ... virgin olive oil was developed by entrapping it in the oily phase of oil-in-water (o/w) emulsion. ... The evaluation parameters consisted of color, smell, phase separation, ...

High-Speed Automatic Microscopy for Real Time Tracks Reconstruction in Nuclear Emulsion

Science.gov (United States)

D'Ambrosio, N.

2006-06-01

The Oscillation Project with Emulsion-tRacking Apparatus (OPERA) experiment will use a massive nuclear emulsion detector to search for /spl nu//sub /spl mu///spl rarr//spl nu//sub /spl tau// oscillation by identifying /spl tau/ leptons through the direct detection of their decay topology. The feasibility of experiments using a large mass emulsion detector is linked to the impressive progress under way in the development of automatic emulsion analysis. A new generation of scanning systems requires the development of fast automatic microscopes for emulsion scanning and image analysis to reconstruct tracks of elementary particles. The paper presents the European Scanning System (ESS) developed in the framework of OPERA collaboration.

Development of an amine-type adsorbent by electron beam-induced emulsion grafting of glycidyl methacrylate onto a nonwoven fabric

International Nuclear Information System (INIS)

Madrid, Jordan; Ueki, Yuji; Seko, Noriaki

2013-01-01

In the recent years, radiation-induced graft polymerization of various monomers onto different types of trunk polymers have been extensively used for researchers on adsorbents for cations, anions and different compounds, battery separators, antibacterial bandages, protein separators, and fuel cell applications. Some of these technologies were transferred to end-users and eventually commercialized. In most of these studies, a post-grafting reaction is performed to introduced chemical groups that impart functionality to the grafted material. In this paper, pre-irradiation technique was used for emulsion grafting of glycidyl methacrylate (GMA) onto an electron beam irradiated abaca-polyester nonwoven fabric (APNWF). The dependence of degree of grafting (Dg), calculated from the weight of APNWF before and after grafting, on irradiation dose, reaction time and monomer concentration were studies. After 50 kGy irradiation with 2 MeV electron beam and subsequent 3-hour reaction with an emulsion consisting of 5% GMA and 0.5% polyoxyethylene sorbitan monolaurate (Tween 20) surfactant in deionized water at 40 degree centegrade, a grafted APNWF with a Dg greater than 150% was obtained. The GMA grafted APNWF was further modified by reaction with ethylenediamine (EDA) in isopropyl alcohol at 60 degree centegrade to introduce amine functional groups. A 3-hour reaction with 50% EDA resulted to an amine group density of 2.7 mmole/gram-adsorbent. Preliminary batch adsorption experiments using Cu 2+ and Ni 2+ ions in aqueous solutions show that the adsorption capacity of the grafted adsorbent is four times greater for Cu 2+ ions compared to Ni 2+ ions. (author)

Beeswax–chitosan emulsion coated paper with enhanced water vapor barrier efficiency

International Nuclear Information System (INIS)

Zhang, Weiwei; Xiao, Huining; Qian, Liying

2014-01-01

Graphical abstract: - Highlights: • The water vapor barrier efficiency of paper was enhanced via green-based emulsion coating. • Extremely high lipid content in the emulsion coating layer was firstly utilized to reduce WVTR in emulsion-based film. • A controlled WVTR of beeswax–chitosan emulsion coating could be obtained by dying at specific temperature. - Abstract: For lipid–hydrocolloid emulsion based film, the increase of lipid amount would improve its water vapor barrier property, but also reduce the mechanical strength of the film in the meantime thus leading to a compromised lipid content in the film. However, when the emulsion is coated on paper surface, more lipid could be used for emulsion preparation to enhance the moisture resistance without considering the weakened strength of the film induced by lipid, because the mechanical properties of emulsion coated paper is mainly governed by the strength of base paper instead of the coating layer. In this study, beeswax–chitosan emulsion was first prepared and then coated on paper surface to improve paper's water vapor barrier and water resistance properties. The range and variance analysis of orthogonal test design showed that the order of priorities of the factors accordingly was beeswax solid content, drying temperature and chitosan concentration. The effect of drying temperature on water vapor transmission rate (WVTR) and water contact angle of coated paper was further investigated using 1.2 wt% chitosan and 96% beeswax solid content in the coating layer. The results indicated that water vapor barrier property was in accordance with the density of the coating layer. Atomic force microscope (AFM) was also used to characterize the surface morphology and explain the hydrophobicity of beeswax–chitosan coated paper. It was found that surface beeswax particles melted to wrinkle at high drying temperatures, while roughness values maintained at micro-scale over the temperature range investigated

New insights about flocculation process in sodium caseinate-stabilized emulsions.

Science.gov (United States)

Huck-Iriart, Cristián; Montes-de-Oca-Ávalos, Juan; Herrera, María Lidia; Candal, Roberto Jorge; Pinto-de-Oliveira, Cristiano Luis; Linares-Torriani, Iris

2016-11-01

Flocculation process was studied in emulsions formulated with 10wt.% sunflower oil, 2, 5 or 7.5wt.% NaCas, and with or without addition of sucrose (0, 5, 10, 15, 20 or 30wt.%). Two different processing conditions were used to prepare emulsions: ultraturrax homogenization or further homogenization by ultrasound. Emulsions with droplets with diameters above (coarse) or below (fine) 1μm were obtained. Emulsions were analyzed for droplet size distribution by static light scattering (SLS), stability by Turbiscan, and structure by confocal laser scanning microscopy (CLSM) and small angle X-ray scattering (SAXS). SAXS data were fitted by a theoretical model that considered a system composed of poly dispersed spheres with repulsive interaction and presence of aggregates. Flocculation behavior was caused by the self-assembly properties of NaCas, but the process was more closely related to interfacial protein content than micelles concentration in the aqueous phase. The results indicated that casein aggregation was strongly affected by disaccharide addition, hydrophobic interaction of the emulsion droplets, and interactions among interfacial protein molecules. The structural changes detected in the protein micelles in different environments allowed understanding the macroscopic physical behavior observed in concentrated NaCas emulsions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Oxygen carrying perfluorochemical emulsion as an adjuvant to radiation therapy

International Nuclear Information System (INIS)

Teicher, B.A.; Rose, C.M.

1984-01-01

The potential of a perfluorochemical emulsion which as an excellent carrying capacity for oxygen to enhance the ability of radiation therapy to delay the growth of Lewis lung tumor was examined. There was a highly significant effect produced by the addition of perfluorochemical emulsion and carbogen breathing in combination with irradiation. With single dose x-ray treatment the dose of perfluorochemical emulsion was varied from 0.05-0.6 ml addition to the blood volume of the animals. The dose response effect was very broad peaking at 0.3-0.4 ml which gave a dose modifying effect of 2.8 +- 0.6 with 1000 rad of x-rays. The addition of 0.3 ml of perfluorochemical free annex solution with carbogen breathing produced a small enhancement in tumor growth delay addition of the same volume of the complete emulsion increased the tumor growth delay time about 3-fold compared to the annex solution. When the perfluorochemical emulsion was added to a fractionated course of radiation therapy a dose modifying effect of 1.8 +- 0.3 was obtained. Oxygen carrying perfluorochemical emulsions may provide a nontoxic clinically useful means of increasing the effectiveness of radiation therapy and of certain chemotherapeutic agents

Dairy-Based Emulsions: Viscosity Affects Fat Difference Thresholds and Sweetness Perception.

Science.gov (United States)

Zahn, Susann; Hoppert, Karin; Ullrich, Franziska; Rohm, Harald

2013-11-27

In complex emulsions, viscosity or viscosity-associated sensory attributes such as creaminess are important for quality assessment and product differentiation. Two sets of emulsions with fat or locust bean gum content being varied at seven levels were developed; the two emulsions at each level had similar apparent viscosity. Additionally, sugar concentration was kept constant either with respect to total emulsion, or with respect to the aqueous phase. Series of two-alternative forced choice tests were performed with one constant stimulus, and just noticeable differences were calculated using probability regression. The results show that, when viscosity was not compensated, it was easy for the subjects to (a) distinguish emulsions with different fat content when the fat content was addressed in the question, and to (b) distinguish emulsions with different fat or locust bean gum content when creaminess was addressed. For the latter descriptor, it is of minor importance whether viscosity is altered by fat content or a thickener. Weber fractions that were calculated for viscosity were approximately 0.20. The quantitative effects of viscosity on sweetness, however, depend on how product rheology was modified.

An Overview of Food Emulsions: Description, Classification and Recent Potential Applications

Directory of Open Access Journals (Sweden)

Meltem Serdaroğlu

2015-03-01

Full Text Available Emulsions take place partially or completely in the structures of many natural and processed foods or some foods are already emulsified in certain stages of production. In general “emulsion” is described as a structure created through the dispersion of one of two immiscible liquids within the other one in form of little droplets. Many terms are available to describe different emulsion types and it is very important to define and clarify these terms like “macro emulsion”, “nanoemulsion” and “multiple emulsion”. Nanoemulsions become increasingly important in food industry as an innovative approach in carrying functional agents. Application potential of multiple emulsions (W/O/W is also stated to be very high in food industry. The two main strategic purposes of utilization of multiple emulsions in food applications are to encapsulate various aromas, bioactive compounds or sensitive food compounds and to allow the production of the low-fat products. This review provides an overview to the general terms of emulsion types, the role of various emulsifying agents, and the application potential of emulsions in food industry.

Pickering Emulsions for Food Applications: Background, Trends, and Challenges

NARCIS (Netherlands)

Berton-Carabin, C.C.; Schroën, C.G.P.H.

2015-01-01

Particle-stabilized emulsions, also referred to as Pickering emulsions, have garnered exponentially increasing interest in recent years. This has also led to the first food applications, although the number of related publications is still rather low. The involved stabilization mechanisms are

Determination of the distribution of graft yields following a radiation-induced graft copolymerization

International Nuclear Information System (INIS)

Schipschack, K.; Wagner, H.; Sawtschenko, L.

1976-01-01

In the radiation-induced graft copolymerization on solid initial polymers a distribution of graft yields takes place along the cross-sections of samples. Methods for determining this distribution, which are described in the literature, are reviewed. In our own investigations boards made of ethylene-vinyl acetate copolymers and grafted with vinyl chloride were used. Distributions of the grafted component obtained by infrared analysis of microtome cuts parallel to the surface are partly rather inhomogeneous, and are interpreted as dependent on the experimental parameters. (author)

Radiation graft copolymerization of styrene with m/e and styrene with acrylic acid at highthyl methacryl dose rate

International Nuclear Information System (INIS)

Aliev, R.Eh.; Kabanov, B.Ya.

1984-01-01

Comparative investigation of radiation graft copolymerization of styrene with methyl methacrylate (MMA) and styrene with acrylic acid (AA) is carried out at considerably differing radiation dose rates. The monomer mixture was grafted to PE low density films at dose rates of 0.16, 0.25 Gy/s (1 MeV electron acceleration). The value of graft was 3-6 and 5-10%, respectively, for the styrene-MMA and styrene-AA systems. An essential difference in the dependences of the formed copolymer composition on initial monomer mixture composition is noticed. Difference in composition of graft polymers prepared at different dose rates is less for the systems with AA, than for systems with MMA. It is shown that at high dose rates in difference with low ones not only radical graft copolymerization of the styrene mixture with AA takes place, but a contribution of the graft styrene polymerization according to cation mechanism as well

Treatment of acute radiodermatitis with an oil-in-water emulsion following radiation therapy for breast cancer. A controlled, randomized trial

International Nuclear Information System (INIS)

Jensen, Jens-Michael; Gau, Tanja; Foelster-Holst, Regina; Proksch, Ehrhardt; May, Theodor

2011-01-01

A side effect of radiotherapy for breast cancer is acute radiodermatitis. It is a common practice to keep irradiated skin dry on account of data from the 1950s that suggested this regimen limits dermatitis. However, severe dryness of the skin induced by irradiation results in itching and discomfort. Dry skin is characterized by scaliness, epidermal barrier dysfunction, and reduced stratum corneum hydration, and these signs and symptoms are reduced by treatment with an emulsion. We performed a randomized, controlled, open-label study with 66 patients (ITT population), treating the irradiated skin in one group (n = 34) with an oil-in-water emulsion (WO1932), while leaving the other group untreated (n = 32). Clinical scoring (ONS radiation skin reaction scoring, pruritus) and biophysical measurements (stratum corneum hydration and transepidermal water loss (TEWL), as a marker of skin barrier function) were determined at day 1 (directly after termination of the radiation therapy), day 8, and day 47 (± 7). Irradiation increased the ONS score and pruritus, whereas skin hydration and TEWL were reduced. The primary hypothesis that the increase in skin hydration was significantly greater in the emulsion-treated compared to the untreated group as early as after 8 days of treatment could not be confirmed. At the end of the study (day 47 ± 7), however, normalization of stratum corneum hydration was more advanced in the treatment group compared to the untreated group and nearly reached the values of the contralateral healthy breast skin. ONS score and pruritus also revealed an advantage for the emulsion-treated group. TEWL did not show significant changes during emulsion treatment. No adverse events were caused by the treatment regimens. Treatment of radiodermatitis with an oil-in-water emulsion was well tolerated, enhanced stratum corneum hydration, improved clinical indicators, and provided relief from itching. (orig.)

Studies on the runaway reaction of ABS polymerization process

International Nuclear Information System (INIS)

Hu, K.-H.; Kao, C.-S.; Duh, Y.-S.

2008-01-01

Taiwan has the largest acrylonitrile-butadiene-styrene (ABS) copolymer production in the world. Preventing on unexpected exothermic reactions and related emergency relief hazard is essential in the safety control of ABS emulsion polymerization. A VSP2 (Vent Sizing Package 2) apparatus is capable of studying both normal and abnormal conditions (e.g., cooling failure, mischarge, etc.) of industrial process. In this study, the scenarios were verified from the following abnormal conditions: loss of cooling, double charge of initiator, overcharge of monomer, without charge of solvent, and external fire. An external fire with constant heating will promote higher self-heat rate and this is recommended as the worst case scenario of emulsion polymerization on butadiene. Cooling failure coupled with bulk system of reactant was determined to be the credible worst case in ABS emulsion polymerization. Finally, the emergency vent sizing based on thermokinetics from VSP associated with DIERS methodology were used for evaluating the vent sizing and compared to that of the industrial plants

Showing Emulsion Properties with Common Dairy Foods

Science.gov (United States)

Bravo-Diaz, Carlos; Gonzalez-Romero, Elisa

1996-09-01

Foods are mixtures of different chemical compounds, and the quality we sense (taste, texture, color, etc.) are all manifestations of its chemical properties. Some of them can be visualized with the aid of simple, safe and inexpensive experiments using dairy products that can be found in any kitchen and using almost exclusively kitchen utensils. In this paper we propose some of them related with food emulsions. Food emulsions cover an extremely wide area of daily-life applications such as milk, sauces, dressings and beverages. Experimentation with some culinary recipes to prepare them and the analyisis of the observed results is close to ideal subject for the introduction of chemical principles, allowing to discuss about the nature and composition of foods, the effects of additives, etc. At the same time it allows to get insights into the scientific reasons that underlie on the recipes (something that it is not usually found in most cookbooks). For example, when making an emulsion like mayonnaise, why the egg yolks and water are the first materials in the bowl , and the oil is added to them rather than in the other way around? How you can "rescue" separate emulsions (mayonnaise)? Which parameters affect emulsion stability? Since safety, in its broad sense, is the first requisite for any food, concerns about food exist throughout the world and the more we are aware of our everyday life, the more likely we will be to deal productively with the consequences. On the other hand, understanding what foods are and how cooking works destroys no delightful mystery of the art of cuisine, instead the mystery expands.

Preparation of LDPE/LNR Blend Via Emulsion Dispersion

International Nuclear Information System (INIS)

Rusli Daik; Yee Lee Ching

2007-01-01

Low density polyethylene (LDPE)/ liquid natural rubber (LNR) blends with the composition of 100LDPE/ 0LNR, 70LDPE/ 30LNR, 60LDPE/ 40LNR and 40LDPE/ 60LNR were prepared via dispersion of LDPE and LNR emulsion. LNR was obtained via photochemical sensitization of natural rubber (NR). Emulsion of LNR was prepared by using sodium dodecyl sulfate (SDS) and 1-hexanol as the emulsifier and co- emulsifier respectively. Emulsion of LDPE was prepared in the same way by using LDPE solution in carbon tetrachloride, SDS and 1-hexanol. LDPE/ LNR blends were prepared via mixing of LNR and LDPE emulsions. Mechanical properties of the blends were analyzed by tensile, hardness and impact test. Optimum mechanical properties were observed for composite with composition of 60LDPE/ 40LNR that showed the maximum value of stress and strain. The glass transition temperature, T g , of the blends as obtained from differential scanning calorimetric (DSC) showed that the blends were homogeneous. Morphology study by using scanning electron microscopy (SEM) also indicates the homogeneity of LDPE/ LNR blends produced. (author)

Perfluorocarbon (PFC) emulsions as potential drug carriers

International Nuclear Information System (INIS)

Yuhas, J.M.; Goodman, R.L.; Moore, R.E.

1984-01-01

PFC emulsions have excellent oxygen transporting properties and have been reported to enhance the response of murine tumors to both radiation and BCNU. While the presently available emulsions are far too toxic to the immune system to be used in cancer therapy, they can be used to investigate the overall potential of this approach. As an example, the authors have found that these emulsions can alter drug availability. The lipophilicity of both the PFC and the drug in question determine the partitioning of the drug between the organic and aqueous phases of an emulsion. In vitro, this can reduce drug effectiveness by reducing the amount of drug available to the cells. In vivo, however, this partitioning may produce sustained drug exposure, which could be of benefit in cancer therapy and other applications. In brief, as the drug is absorbed from the circulating aqueous phase, additional drug would leach from the PFC, thereby providing a sustained drug exposure similar to that obtained with liposomes. While a great deal more work will be required to evaluate the practicality of this approach, the existence of this phenomenon must be taken into account in both the design and interpretation of efficacy studies in which anesthetics, chemotherapeutics, etc are employed

Microfluidic emulsion separation-simultaneous separation and sensing by multilayer nanofilm structures

Energy Technology Data Exchange (ETDEWEB)

Uhlmann, P; Truman, P; Stamm, M [Leibniz-Institut fuer Polymerforschung Dresden e V, Hohe Strasse 6, 01069 Dresden (Germany); Varnik, F; Zikos, G [Ruhr Universitaet Bochum, Stiepeler Strasse 129, 44801 Bochum (Germany); Moulin, J-F; Mueller-Buschbaum, P, E-mail: uhlmannp@ipfdd.de [Technische Universitaet Muenchen, Physik-Department, LS E13, James-Franck-Strasse 1, 85748 Garching (Germany)

2011-05-11

Emulsion separation is of high relevance for filtration applications, liquid-liquid-partitioning of biomolecules like proteins and recovery of products from droplet microreactors. Selective interaction of various components of an emulsion with substrates is used to design microfluidic flow chambers for efficient separation of emulsions into their individual components. Our lab-on-a-chip device consists of an emulsion separation cell with an integrated silicon sensor chip, the latter allowing the detection of liquid motion via the field-effect signal. Thus, within our lab-on-a-chip device, emulsions can be separated while the separation process is monitored simultaneously. For emulsion separation a surface energy step gradient, namely a sharp interface between the hydrophobic and hydrophilic parts of the separation chamber, is used. The key component of the lab-on-a-chip system is a multilayer and multifunctional nanofilm structure which not only provides the surface energy step gradient for emulsion separation but also constitutes the functional parts of the field-effect transistors. The proof-of-principle was performed using a model emulsion consisting of immiscible aqueous and organic solvent components. Droplet coalescence was identified as a key aspect influencing the separation process, with quite different effects during separation on open surfaces as compared to slit geometry. For a detailed description of this observation, an analytical model was derived and lattice Boltzmann computer simulations were performed. By use of grazing incidence small angle x-ray scattering (GISAXS) interfacial nanostructures during gold nanoparticle deposition in a flow field were probed to demonstrate the potential of GISAXS for in situ investigations during flow.

Study of Some Technical Problems in Nuclear Emulsions

International Nuclear Information System (INIS)

Tarrega Tornero, M. P.

1967-01-01

A methodological study of various technical aspects of photographic emulsions is presented. This study enables the emulsion method to be used in certain physical problems, and can be summarized under the following headings. 1) Variation of different ionization indices with the degree of development. A measure of the degree of development is introduced. This measure called the α -mark, is based on the average width of tracks due to α-particles. Using the α-mack the influence of several factors such as the duration, temperature and concentration of the developing liquid are investigated. A comparative study of the sensitivity of llford C 2 and K 2 emulsions is given. (Author) 9 refs

Application of pork fat diacylglycerols in meat emulsions

DEFF Research Database (Denmark)

Miklos, Rikke; Xu, Xuebing; Lametsch, Rene

2011-01-01

The properties of fat are of major importance when meat products are produced. By enzymatic modification triacylglycerols (TAGs) can be converted to diacylglycerols (DAGs) resulting in changes of the physical and chemical properties of the fat. In this study the texture as well as the hydration...... and binding properties were investigated in meat emulsions prepared with lard substituted with different amounts of DAGs derived from the lard. In emulsions prepared with DAGs the percentage of total expressible fluid decreased from 28.2% in products prepared with lard to 11.8% in emulsions prepared with 100....... The results suggest future opportunities for the application of DAGs to improve the quality of meat products....

Study on curing reaction of 4-aminophenoxyphthalonitrile/bisphthalonitrile

Institute of Scientific and Technical Information of China (English)

Xiao

2010-01-01

A series of phthalonitrile blending resins were prepared from 4-aminophenoxyphthalonitrile (APN) and 4,4'-bis (3,4-dicyanophenoxy)biphenyl (BPH) by directly powder-mixing and copolymerization. Differential scanning calorimeter (DSC) and dynamic rheology were used to study the curing reaction behaviors of APN/BPH blends, and the results indicated that the introduction of APN accelerated the curing rate of BPH, and the existence of BPH decreased the curing temperature of APN/BPH systems. The thermal stability of postcured APN/BPH resins was investigated by thermogravimetric analysis (TGA), and the TGA results indicated that the crosslinked polymers of APN/BPH systems possessed good thermal stability.

Volatile release from self-assembly structured emulsions: effect of monoglyceride content, oil content, and oil type.

Science.gov (United States)

Mao, Like; Roos, Yrjö H; Miao, Song

2013-02-20

Monoglycerides (MGs) can form self-assembled structures in emulsions, which can be used to control volatile release. In this study, initial headspace concentrations (C(initial)), maximum headspace concentrations (C(max)), release rates, and partition coefficients of propanol, diacetyl, hexanal, and limonene were determined in MG structured oil-in-water emulsions using dynamic and static headspace analyses. For all of the volatile compounds, C(initial) values above structured emulsions were significantly lower than those above unstructured emulsions and decreased with increasing MG contents (p triglyceride emulsions than in soybean oil emulsions (p structured emulsions than in unstructured emulsions (p structured emulsions can be potentially used as delivery systems to modulate volatile release.

Dietary protein and fat emulsions, processed by ultrasound and pulsed magnetic field

Directory of Open Access Journals (Sweden)

E. I. Verboloz

2017-01-01

Full Text Available For the baking of baked goods in order to save fats, different types of endorsement and protein-fatty emulsions which are used as ingredients in goods and for the protection of metal moulds from burning. Usually emulsion is prepared on bakery enterprises by National State Standard Р 51785–2001, involving mechanical beating up of ingredients. The authors suggested and studied the way of manufacturing of more stable food protein-fatty emulsions using ultrasonic transmitter with rigid neodymium magnets on its thickener. As ingredients, there were applied curd whey diluted with water, unpurified sunflower oil and sunflower phosphatides. Ratio of whey and water is 1:7. Physical effects of ultrasound and field of magnets in contact layer of liquid ingredients being dispersed have increased the viscosity and dispersion of protein-fatty emulsions. Hypothesis of increase of stability and sterility of protein-fatty emulsion by the selection of parameters of magnetic field and power of ultrasound transmitter is confirmed experimentally. Microscopic analysis shows high degree of homogeneity of emulsion under the time of processing 3-4 minutes and intensity of ultrasound 2 W/cm2, that is energetically profitable. There was revealed synergism of influence of physical effects of ultrasound and magnetic field on the durability and steadiness of emulsion to mechanical and temperature effect and also cidal effect, prolonging terms of product using. Manufacture of emulsions by the declared way using the ultrasound and magnetic field of constant neodymium magnets decreases number of injected elements-emulsifiers by 3-4 times or excludes their use at all. Existing piezoelectric ultrasound units as well as neodymium magnets have small sizes and low energy consumption, easily built into the line of continuous manufacture of emulsion for the bread production. Such emulsions are less demanding to the storage and transportation.

Special photographic emulsions for high LET dosimetry

International Nuclear Information System (INIS)

Katz, R.

1978-12-01

The purpose of these investigations into photographic emulsion dosimetry is to attempt to use the photographic emulsion to mimic the response of human tissues to high LET radiations. The program therefore requires that a systematic understanding of the response of mammalian cells to ionizing radiations be achieved. We have been concerned with differences in RBE and in radiation response to both high and LET radiations, and in the interrelationship between observations with these different radiations

Radiation induced copolymerization of N-vinyl-2-pyrrolidone with vinyl acetate [Paper No. RD-3

International Nuclear Information System (INIS)

Ramakrishna, M.S.; Dhal, P.K.; Deshpande, D.D.; Babu, G.N.

1982-01-01

Copolymerization of N-vinyl-2-pyrrolidone (NVP) with vinyl acetate (VAC) was carried out using gamma-ray radiation. The compositions of the copolymers were determined from elemental analysis and the monomer reactivity ratios have been calculated using YBR method. The glass transition temperature and the intrinsic viscosities of the copolymers have been determined. All the experimental results were discussed in terms of the nature of the monomers. (author)

RAFT copolymerization of itaconic anhydride and 2-methoxyethyl acrylate: a multifunctional scaffold for preparation of “clickable” gold nanoparticles

DEFF Research Database (Denmark)

Javakhishvili, Irakli; Kasama, Takeshi; Jankova, Katja Atanasova

2013-01-01

RAFT copolymerization of 2-methoxyethyl acrylate and itaconic anhydride – a monomer derived from renewable resources – is carried out in a controlled fashion. The copolymer allows preparation of gold nanoparticles with abundant surficial carboxyl and alkyne functional groups that are dendronized...

Monomers capable of forming four hydrogen bridges and supramolecular polymers formed by copolymerization of these monomers with regular monomers

NARCIS (Netherlands)

2004-01-01

The invention relates to the synthesis of polymers containing self-complementary quadruple hydrogen groups by copolymerizing monomers containing a quadruple hydrogen bonding group with one or more monomers of choice. The resulting polymers show unique new characteristics due to the presence of

Reduced Fat Food Emulsions: Physicochemical, Sensory, and Biological Aspects.

Science.gov (United States)

Chung, Cheryl; Smith, Gordon; Degner, Brian; McClements, David Julian

2016-01-01

Fat plays multiple important roles in imparting desirable sensory attributes to emulsion-based food products, such as sauces, dressings, soups, beverages, and desserts. However, there is concern that over consumption of fats leads to increased incidences of chronic diseases, such as obesity, coronary heart disease, and diabetes. Consequently, there is a need to develop reduced fat products with desirable sensory profiles that match those of their full-fat counterparts. The successful design of high quality reduced-fat products requires an understanding of the many roles that fat plays in determining the sensory attributes of food emulsions, and of appropriate strategies to replace some or all of these attributes. This paper reviews our current understanding of the influence of fat on the physicochemical and physiological attributes of food emulsions, and highlights some of the main approaches that can be used to create high quality emulsion-based food products with reduced fat contents.

Oil-in-water emulsions stabilised by cellulose ethers: stability, structure and in vitro digestion.

Science.gov (United States)

Borreani, Jennifer; Espert, María; Salvador, Ana; Sanz, Teresa; Quiles, Amparo; Hernando, Isabel

2017-04-19

The effect of cellulose ethers in oil-in-water emulsions on stability during storage and on texture, microstructure and lipid digestibility during in vitro gastrointestinal digestion was investigated. All the cellulose ether emulsions showed good physical and oxidative stability during storage. In particular, the methylcellulose with high methoxyl substituents (HMC) made it possible to obtain emulsions with high consistency which remained almost unchanged during gastric digestion, and thus could enhance fullness and satiety perceptions at gastric level. Moreover, the HMC emulsion slowed down lipid digestion to a greater extent than a conventional protein emulsion or the emulsions stabilised by the other cellulose ethers. Therefore, HMC emulsions could be used in weight management to increase satiation capacity and decrease lipid digestion.

Synthesis and Study of Shape-Memory Polymers Selectively Induced by Near-Infrared Lights via In Situ Copolymerization

Directory of Open Access Journals (Sweden)

Tianyu Fang

2017-05-01

Full Text Available Shape-memory polymers (SMPs selectively induced by near-infrared lights of 980 or 808 nm were synthesized via free radical copolymerization. Methyl methacrylate (MMA monomer, ethylene glycol dimethylacrylate (EGDMA as a cross-linker, and organic complexes of Yb(TTA2AAPhen or Nd(TTA2AAPhen containing a reactive ligand of acrylic acid (AA were copolymerized in situ. The dispersion of the organic complexes in the copolymer matrix was highly improved, while the transparency of the copolymers was negligibly influenced in comparison with the pristine cross-linked PMMA. In addition, the thermal resistance of the copolymers was enhanced with the complex loading, while their glass transition temperature, cross-linking level, and mechanical properties were to some extent reduced. Yb(TTA2AAPhen and Nd(TTA2AAPhen provided the prepared copolymers with selective photothermal effects and shape-memory functions for 980 and 808 nm NIR lights, respectively. Finally, smart optical devices which exhibited localized transparency or diffraction evolution procedures were demonstrated based on the prepared copolymers, owing to the combination of good transparency and selective light wavelength responsivity.

Stability and in vitro digestibility of emulsions containing lecithin and whey proteins.

Science.gov (United States)

Mantovani, Raphaela Araujo; Cavallieri, Ângelo Luiz Fazani; Netto, Flavia Maria; Cunha, Rosiane Lopes

2013-09-01

The effect of pH and high-pressure homogenization on the properties of oil-in-water (O/W) emulsions stabilized by lecithin and/or whey proteins (WPI) was evaluated. For this purpose, emulsions were characterized by visual analysis, droplet size distribution, zeta potential, electrophoresis, rheological measurements and their response to in vitro digestion. Lecithin emulsions were stable even after 7 days of storage and WPI emulsions were unstable only at pH values close to the isoelectric point (pI) of proteins. Systems containing the mixture of lecithin and WPI showed high kinetic instability at pH 3, which was attributed to the electrostatic interaction between the emulsifiers oppositely charged at this pH value. At pH 5.5 and 7, the mixture led to reduction of the droplet size with enhanced emulsion stability compared to the systems with WPI or lecithin. The stability of WPI emulsions after the addition of lecithin, especially at pH 5.5, was associated with the increase of droplet surface charge density. The in vitro digestion evaluation showed that WPI emulsion was more stable against gastrointestinal conditions.

Destabilization of Oil-in-Water Emulsions Formed Using Highly Hydrolyzed Whey Proteins.

Science.gov (United States)

Agboola; Singh; Munro; Dalgleish; Singh

1998-01-19

Oil-in-water emulsions (4 wt % soy oil) were prepared with 0.5-5 wt % whey protein hydrolysate (WPH) (27% degree of hydrolysis), in a two-stage homogenizer using various first-stage pressures of 10.3, 20.6, and 34.3 MPa and a constant second-stage pressure of 3.4 MPa. Destabilization studies on the emulsions were carried out for up to 24 h, using both laser light scattering and confocal laser microscopy. It was found that emulsions formed with oiling off and coalescence at all homogenization pressures. Emulsions formed with 2, 3, and 4% WPH showed coalescence and creaming only, while slight flocculation but no creaming occurred in emulsions formed with 5% WPH. Furthermore, the apparent rate of coalescence increased with homogenization pressure but decreased with WPH concentration. In contrast, the surface concentration of WPH increased with the WPH concentration in the emulsions but decreased with homogenization pressure. Analysis of WPH by high-performance liquid chromatography showed an increase in the concentration of high molecular weight peptides at the droplet surface compared to the WPH solution. This was considered very important for the stability of these oil-in-water emulsions.

Graft copolymerization of polystyrene onto chitosan congress as an adsorbent for the removal of heavy metal ions

International Nuclear Information System (INIS)

Dela Mines, Remedel D.; Muncal, Danilet Vi A.

2013-01-01

Chitosan is primarily composed of glucosamine, 2-amino-2-deoxy-β-D-glucose. Chitosan has different types of reactive functional groups. Both hydroxyl and amino groups are possible sites for the reaction to incorporate new and desired functional groups. By modification of these groups various materials for different field of application can be achieved. Chitosan has been used as adsorbent for the removal of heavy metal ions from aqueous solution through adsorption process. Properties of chitosan, such as solubility, mechanical stability and adsorption compatibility, are enhanced by grafting. In this study, chitosan was graft copolymerized with polystyrene for wastewater treatment and evaluated its effectiveness in removing toxic heavy metals by adsorption. Chitosan-graft-polystyrene was characterized by FTIR spectroscopy, and SEM. Adsorption study of the copolymer is carried out as a function of adsorbent dose, pH, and contact time. Residual concentration was measured by Atomic Absorption Spectroscopy. To get an insight of the rate of adsorption and the rate limiting step of the transport mechanism, kinetic analysis was utilized. Langmuir equation/isotherm was used for proper quantification of the sorption equilibrium in the bio sorption process (author)

Oil-in-Water Emulsions Stabilized by Saponified Epoxidized Soybean Oil-Grafted Hydroxyethyl Cellulose.

Science.gov (United States)

Huang, Xujuan; Li, Qiaoguang; Liu, He; Shang, Shibin; Shen, Minggui; Song, Jie

2017-05-03

An oil-in-water emulsion stabilized by saponified epoxidized soybean oil-grafted hydroxyethyl cellulose (H-ESO-HEC) was investigated. By using an ultrasonic method, oil-in-water emulsions were prepared by blending 50 wt % soybean oil and 50 wt % H-ESO-HEC aqueous suspensions. The influence of H-ESO-HEC concentrations on the properties of oil-in-water emulsions was examined. The H-ESO-HEC concentrations in the aqueous phase varied from 0.02 to 0.40 wt %. When the H-ESO-HEC concentration was 0.4 wt %, the emulsion remained stable for >80 days. The mean droplet sizes of the emulsions decreased by increasing the H-ESO-HEC concentration and extending the ultrasonic time. The adsorption amounts of H-ESO-HEC at the oil-water interface increased when the H-ESO-HEC concentrations in the aqueous phase increased. The rheological property revealed that the apparent viscosity of the H-ESO-HEC-stabilized oil-in-water emulsions increased when the H-ESO-HEC concentrations increased. Steady flow curves indicated an interfacial film formation in the emulsions. The evolution of G', G″, and tan η indicated the predominantly elastic behaviors of all the emulsions.

Stabilization of heavy oil-water emulsions using a bio/chemical emulsifier mixture

Energy Technology Data Exchange (ETDEWEB)

Farahbakhsh, A.; Taghizadeh, M.; Movagharnejad, K. [Chemical Engineering Department, Babol University of Technology, Babol (Iran, Islamic Republic of); Yakhchali, B. [National Institute of Genetic Engineering and Biotechnology, Tehran (Iran, Islamic Republic of)

2011-11-15

In this study, the viscosity reduction of heavy oil has been investigated through the formation of oil-water emulsion using a bio/chemical emulsifier mixture. Four bioemulsifiers from indigenous Rhodococcus ergthropolis and Bacillus licheniformis strains were used to stabilize a highly-viscous oil-in-water emulsion. The Taguchi method with an L{sub 9} orthogonal array design was used to investigate the effect of various control factors on the formation of the oil/water emulsions. An emulsion with lowest viscosity was formed using ACO4 strain. The substantial stability of the oil-in-water emulsion allows the heavy oil to be transported practically over long distances or remain stationary for a considerable period of time prior to utilization. As the result of Taguchi analysis, the temperature and concentration of the emulsifier had a significant influence on viscosity reduction of the emulsion. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Phosphine-Thiophenolate Half-Titanocene Chlorides: Synthesis, Structure, and Their Application in Ethylene (Co-Polymerization

Directory of Open Access Journals (Sweden)

Yue-Sheng Li

2013-03-01

Full Text Available A series of novel half-titanocene complexes CpTiCl2[S-2-R-6-(PPh2C6H3] (Cp = C5H5, 2a, R = H; 2b, R = Ph; 2c, R = SiMe3 have been synthesized by treating CpTiCl3 with the sodium of the ligands, 2-R-6-(PPh2C6H3SNa, which were prepared by the corresponding ligands and NaH. These complexes have been characterized by 1H, 13C and 31P NMR as well as elemental analyses. Structures for 2a–b were further confirmed by X-ray crystallography. Complexes 2a–b adopt five-coordinate, distorted square-pyramid geometry around the titanium center, in which the equatorial positions are occupied by sulfur and phosphorus atoms of the chelating phosphine-thiophenolate and two chlorine atoms, and the cyclopentadienyl ring is coordinated on the axial position. The complexes 2a–c were investigated as the catalysts for ethylene polymerization and copolymerization of ethylene with norbornene in the presence of MMAO or Ph3CB(C6F54/iBu3Al as the cocatalyst. All complexes exhibited low to moderate activities towards homopolymerization of ethylene. However, they displayed moderate to high activities towards copolymerization of ethylene with norbornene.

Graft copolymerization of a series of alkyl acrylates and alkyl methacrylates onto polyethylene

International Nuclear Information System (INIS)

Zurakowska-Orszagh, J.; Soerjosoeharto, K.; Busz, W.; Oldziejewski, J.

1977-01-01

Graft copolymerization of a series of alkyl acrylates and alkyl methacrylates into polyethylene of Polish production was investigated, using benzoyl peroxide as the initiator as well as preirradiation technique, namely ionizing radiation from a 60 Co γ-source. The effect of α-carbon methyl substituent of methacrylates as well as the influence of the length of alkyl chains in the ester groups of both series of monomers into the grafting process was observed. The ungrafted and some of the grafted polyethylene film obtained was studied by infrared spectrophotometry. (author)

Dairy-Based Emulsions: Viscosity Affects Fat Difference Thresholds and Sweetness Perception

Directory of Open Access Journals (Sweden)

Susann Zahn

2013-11-01

Full Text Available In complex emulsions, viscosity or viscosity-associated sensory attributes such as creaminess are important for quality assessment and product differentiation. Two sets of emulsions with fat or locust bean gum content being varied at seven levels were developed; the two emulsions at each level had similar apparent viscosity. Additionally, sugar concentration was kept constant either with respect to total emulsion, or with respect to the aqueous phase. Series of two-alternative forced choice tests were performed with one constant stimulus, and just noticeable differences were calculated using probability regression. The results show that, when viscosity was not compensated, it was easy for the subjects to (a distinguish emulsions with different fat content when the fat content was addressed in the question, and to (b distinguish emulsions with different fat or locust bean gum content when creaminess was addressed. For the latter descriptor, it is of minor importance whether viscosity is altered by fat content or a thickener. Weber fractions that were calculated for viscosity were approximately 0.20. The quantitative effects of viscosity on sweetness, however, depend on how product rheology was modified.

Strippable core-shell polymer emulsion for decontamination of radioactive surface contamination

International Nuclear Information System (INIS)

Hwang, Ho-Sang; Seo, Bum-Kyoung; Lee, Kune-Woo

2011-01-01

In this study, the core-shell composite polymer for decontamination from the surface contamination was synthesized by the method of emulsion polymerization and blends of polymers. The strippable polymer emulsion is composed of the poly(styrene-ethyl acrylate) [poly(St-EA)] composite polymer, poly(vinyl alcohol) (PVA) and polyvinylpyrrolidone (PVP). The morphology of the poly(St-EA) composite emulsion particle was core-shell structure, with polystyrene (PS) as the core and poly(ethyl acrylate) (PEA) as the shell. Core-shell polymers of styrene (St)/ethyl acrylate (EA) pair were prepared by sequential emulsion polymerization in the presence of sodium dodecyl sulfate (SDS) as an emulsifier using ammonium persulfate (APS) as an initiator. Related tests and analysis confirmed the success in synthesis of composite polymer. The products are characterized by FT-IR spectroscopy, TGA that were used, respectively, to show the structure, the thermal stability of the prepared polymer. Two-phase particles with a core-shell structure were obtained in experiments where the estimated glass transition temperature and the morphologies of emulsion particles. Decontamination factors of the strippable polymeric emulsion were evaluated with the polymer blend contents. (author)

Supralinearity and particle discrimination in nuclear emulsion

International Nuclear Information System (INIS)

Katz, R.; Larsson, L.; Pinkerton, F.E.; Benton, E.V.

1977-01-01

Nuclear emulsions may be desensitized in manufacture and/or may be so processed as to discriminate against small latent image sites; to yield supralinear sensitometric response after x-irradiation; and to discriminate against lightly ionizing radiations in favor of heavily ionizing particles. In a circumstance where one electron passing through an emulsion grain is unlikely to generate a latent image sufficiently large to yield a visible grain after development, some larger number of electrons is required, resulting in 'many-hit' statistics, supralinearity, and particle discrimination: for lightly ionizing particles are not likely to generate more than one delta-ray (secondary electron) in their passage through or near a grain. Since these properties are analogous to the response of many biological cells to ionizing radiations, such emulsion-developer combinations have the potential to mimic the response of biological systems to particulate radiations of different charge and speed. (author)

Interstitial administration of perfluorochemical emulsions for reoxygenation of hypoxic tumor cells

International Nuclear Information System (INIS)

Woo, D.V.; Seegenschmiedt, H.; Schweighardt, F.K.; Emrich, J.; McGarvey, K.; Caridi, M.; Brady, L.W.

1987-01-01

Microparticulate perfluorochemical (PFC) emulsions have the capacity to solubilize significant quantities of oxygen compared to water. Although systemic administration of such emulsions may enhance oxygen delivery to some tissues, hypoxic tumor cells have marginal vascular supplies. The authors report studies which directly attempt to oxygenate hypoxic tumor cells by interstitial administration of oxygenated PFC emulsions followed by radiation therapy. Fortner MMI malignant melanomas (21 day old) grown in Syrian Golden hamsters were injected directly with either oxygenated PFC emulsions or Ringers solution. The volume of test substance administered was equal to 50% of the tumor volume. The tumors were immediately irradiated with 25 Gy of 10 MeV photons (Clinac 18). The tumor dimensions were measured daily post irradiation and the tumor doubling time determined. The results suggest that interstitial administration of oxygenated PFC emulsions directly into tumors followed by radiation therapy may increase the likelihood of killing hypoxic tumor cells

Active Ester Containing Surfmer for One-Stage Polymer Nanoparticle Surface Functionalization in Mini-Emulsion Polymerization

Directory of Open Access Journals (Sweden)

Vanessa L. Albernaz

2018-04-01

Full Text Available Functional surface active monomers (surfmers are molecules that combine the functionalities of surface activity, polymerizability, and reactive groups. This study presents an improved pathway for the synthesis of the active ester containing surfmer p-(11-acrylamidoundecanoyloxyphenyl dimethylsulfonium methyl sulfate (AUPDS. Further, the preparation of poly(methyl methacrylate and polystyrene nanoparticles (NPs by mini-emulsion polymerization using AUPDS is investigated, leading to NPs with active ester groups on their surface. By systematically varying reaction parameters and reagent concentrations, it was found that AUPDS feed concentrations between 2–4 mol% yielded narrowly distributed and stable spherical particles with average sizes between 83 and 134 nm for non-cross-linked NPs, and up to 163 nm for cross-linked NPs. By basic hydrolysis of the active ester groups in aqueous dispersion, the positive ζ-potential (ZP was converted into a negative ZP and charge quantities determined by polyelectrolyte titrations before and after hydrolysis were in the same range, indicating that the active ester groups were indeed accessible in aqueous suspension. Increasing cross-linker amounts over 10 mol% also led to a decrease of ZP of NPs, probably due to internalization of the AUPDS during polymerization. In conclusion, by using optimized reaction conditions, it is possible to prepare active ester functionalized NPs in one stage using AUPDS as a surfmer in mini-emulsion polymerization.

DMC-grafted cellulose as green-based flocculants for agglomerating fine kaolin particles

Directory of Open Access Journals (Sweden)

Meng Li

2018-04-01

Full Text Available Novel cellulose based flocculants C-g-P (DMC with various chain architectures are synthesized through a situ graft copolymerization. The cationic ammonium chloride group (DMC is grafted onto cellulose by two separate inverse emulsion polymerization with γ-methacryloxypropyl trimethoxy silane (KH-570 and double bond addition reactions, which is a new and simple method to employ KH-570 as a bridge for the connection of cellulose matrix and DMC group. The effects of pH, flocculant dose, standing time on turbidity of kaolin suspensions and particle sizes have been studied systematically. In addition, the response surface methodology (RSM study confirms that PAC and C-g-P (DMC have synergy in turbidity removal with a higher removal efficiency of 98.32%. Moreover, C-g-P (DMC 1 has higher removal efficiency with 96.5% at a low dosage of 0.6 mg L−1 and better floc properties than C-g-P (DMC 2 and C-g-P (DMC 3, suggesting that the length and quantity of cationic branch chains play a crucial role in Kaolin flocculation due to their dramatically enhanced bridging effects. Keywords: Cellulose, Cationic flocculant, Inverse emulsion polymerization, Kaolin suspension

Excretion and organic distribution of 57Co-bleomycin emulsions

International Nuclear Information System (INIS)

Lathan, B.

1982-01-01

Excretion and organic distributions of 57 Co-bleomycin were studied in normal and tumour-bearing mice with the objective of obtaining high 57 Co-bleomycin concentrations in the tumour and the regional lymph nodes. Aqueous 57 Co-bleomycin and various 57 Co-bleomycin emulsions were used for the studies and applied either locally or systemically. Excretion of 57 Co-bleomycin was slowest after local administration of 57 Co-bleomycin oil-in-water emulsion and fastest after systemic application of aqueous 57 Co-bleomycin. Organic distribution studies showed the highest values in the tumour and the regional lymph nodes after local injection of 57 Co-bleomycin oil-in-water emulsion while the lowest values were measured after systemic application of aqueous 57 Co-bleomycin. These kinetic studies suggest that intratumoral treatment with oil-in-water emulsions of bleomycin may be a new approach in the therapy of epithelial tumours with lymphogenic metastases. (orig.) [de

Computational Investigation of the Competition between the Concerted Diels-Alder Reaction and Formation of Diradicals in Reactions of Acrylonitrile with Non-Polar Dienes

Science.gov (United States)

James, Natalie C.; Um, Joann M.; Padias, Anne B.; Hall, H. K.; Houk, K. N.

2013-01-01

The energetics of the Diels-Alder cycloaddition reactions of several 1,3-dienes with acrylonitrile, and the energetics of formation of diradicals, were investigated with density functional theory (B3LYP and M06-2X) and compared to experimental data. For the reaction of 2,3-dimethyl-1,3-butadiene with acrylonitrile, the concerted reaction is favored over the diradical pathway by 2.5 kcal/mol using B3LYP/6-31G(d); experimentally this reaction gives both cycloadduct and copolymer. The concerted cycloaddition of cyclopentadiene with acrylonitrile is preferred computationally over the stepwise pathway by 5.9 kcal/mol; experimentally, only the Diels-Alder adduct is formed. For the reactions of (E)-1,3-pentadiene and acrylonitrile, both cycloaddition and copolymerization were observed experimentally; these trends were mimicked by the computational results, which showed only a 1.2 kcal/mol preference for the concerted pathway. For the reactions of (Z)-1,3-pentadiene and acrylonitrile, the stepwise pathway is preferred by 3.9 kcal/mol, in agreement with previous experimental findings that only polymerization occurs. M06-2X is known to give more accurate activation and reaction energetics but the energies of diradicals are too high. PMID:23758325

Oxidative enzymatic gelation of sugar beet pectin for emulsion stabilization

DEFF Research Database (Denmark)

Abang Zaidel, Dayang Norulfairuz; Meyer, Anne S.

2013-01-01

Pectin from sugar beet is derived from the sugar beet pulp residue which results when sugar beets are processed for sucrose extraction. The sugar beet pectin has poor gelationability by the classic divalentcation molecular mechanism because of a relatively high acetylation degree and short...... polygalacturonate backbone chain length. However, due to the feruloyl-substitutions on the side chains, the sugar beet pectic polysaccharides can be cross-linked via enzyme catalyzed oxidation. The enzyme kinetics and functionality of such oxidativelycross-linked sugar beet pectin, in relation to stabilizing...... emulsions has recently been investigated in model food emulsions. This paper reviews the pectin chemistry, enzymatic oxidative gelation mechanisms, interaction mechanisms of the sugar beet pectin with the emulsion droplets and explores how the gelation affects the rheology and stability of emulsion systems...

Radiation dosimetry and spectrometry with superheated emulsions

International Nuclear Information System (INIS)

D'Errico, Francesco

2001-01-01

Detectors based on emulsions of overexpanded halocarbon droplets in tissue equivalent aqueous gels or soft polymers, known as 'superheated drop detectors' or 'bubble (damage) detectors', have been used in radiation detection, dosimetry and spectrometry for over two decades. Recent technological advances have led to the introduction of several instruments for individual and area monitoring: passive integrating meters based on the optical or volumetric registration of the bubbles, and active counters detecting bubble nucleations acoustically. These advances in the instrumentation have been matched by the progress made in the production of stable and well-specified emulsions of superheated droplets. A variety of halocarbons are employed in the formulation of the detectors, and this permits a wide range of applications. In particular, halocarbons with a moderate degree of superheat, i.e. a relatively small difference between their operating temperature and boiling point, can be used in neutron dosimetry and spectrometry since they are only nucleated by energetic heavy ions such as those produced by fast neutrons. More recently, halocarbons with an elevated degree of superheat have been utilised to produce emulsions that nucleate with much smaller energy deposition and detect low linear energy transfer radiations, such as photons and electrons. This paper reviews the detector physics of superheated emulsions and their applications in radiation measurements, particularly in neutron dosimetry and spectrometry

Interplay between Colloids and Interfaces : Emulsions, Foams and Microtubes

NARCIS (Netherlands)

de Folter, J.W.J.

2013-01-01

The central theme of this thesis is the interplay between colloids and interfaces. The adsorption of colloids at fluid-fluid interfaces is the main topic and covers Chapters 2-6. Pickering emulsions where colloidal particles act as emulsion stabilizers in the absence of surfactants are studied in a

Evaluation of short-term and long-term stability of emulsions by centrifugation and NMR

International Nuclear Information System (INIS)

Tcholakova, S.; Denkov, N.; Ivanov, I.; Marinov, R.

2004-01-01

The effect of storage time on the coalescence stability and drop size distribution of egg yolk and whey protein concentrate stabilized emulsions is studied. The emulsion stability is evaluated by centrifugation, whereas the drop size distribution is measured by means of NMR and optical microscopy. The experimental results show that there is no general relation between the emulsion stability and the changes in the mean drop diameter upon shelf-storage of protein emulsions. On the other hand, it is shown that the higher short-term stability, measured by centrifugation immediately after emulsion preparation, corresponds to higher long-term stability (after their self-storage up to 60 days) for emulsions stabilized by the same type of emulsifier. In this way, we are able to obtain information for the long-term stability of emulsions in a relatively short period of time.(authors)

A Robust Oil-in-Oil Emulsion for the Nonaqueous Encapsulation of Hydrophilic Payloads.

Science.gov (United States)

Lu, Xiaocun; Katz, Joshua S; Schmitt, Adam K; Moore, Jeffrey S

2018-03-14

Compartmentalized structures widely exist in cellular systems (organelles) and perform essential functions in smart composite materials (microcapsules, vasculatures, and micelles) to provide localized functionality and enhance materials' compatibility. An entirely water-free compartmentalization system is of significant value to the materials community as nonaqueous conditions are critical to packaging microcapsules with water-free hydrophilic payloads while avoiding energy-intensive drying steps. Few nonaqueous encapsulation techniques are known, especially when considering just the scalable processes that operate in batch mode. Herein, we report a robust oil-in-oil Pickering emulsion system that is compatible with nonaqueous interfacial reactions as required for encapsulation of hydrophilic payloads. A major conceptual advance of this work is the notion of the partitioning inhibitor-a chemical agent that greatly reduces the payload's distribution between the emulsion's two phases, thus providing appropriate conditions for emulsion-templated interfacial polymerization. As a specific example, an immiscible hydrocarbon-amine pair of liquids is emulsified by the incorporation of guanidinium chloride (GuHCl) as a partitioning inhibitor into the dispersed phase. Polyisobutylene (PIB) is added into the continuous phase as a viscosity modifier for suitable modification of interfacial polymerization kinetics. The combination of GuHCl and PIB is necessary to yield a robust emulsion with stable morphology for 3 weeks. Shell wall formation was accomplished by interfacial polymerization of isocyanates delivered through the continuous phase and polyamines from the droplet core. Diethylenetriamine (DETA)-loaded microcapsules were isolated in good yield, exhibiting high thermal and chemical stabilities with extended shelf-lives even when dispersed into a reactive epoxy resin. The polyamine phase is compatible with a variety of basic and hydrophilic actives, suggesting that this

Effects of a fish oil-based emulsion on rat hepatoma cell invasion in culture.

Science.gov (United States)

Hagi, Akifumi; Nakayama, Mitsuo; Miura, Yutaka; Yagasaki, Kazumi

2007-01-01

Total parenteral nutrition containing a lipid emulsion is often employed after surgical tumor resection. This study investigated the effects of a fish oil-based infusion on rat hepatoma cell invasion. Rat ascites hepatoma cell line AH109A was precultured with a fish oil-based or safflower oil-based emulsion for 48 h. Changes in membranous fatty acid composition were evaluated by gas chromatography. The invasiveness of hepatoma cells was assessed by coculturing with mesentery-derived mesothelial cells. To examine ex vivo effects of the fish oil-based infusion on hepatoma invasion, sera were prepared from rats infused with fish oil- or safflower oil-based emulsion and the effects of these sera were assessed. To clarify the mechanism of inhibition of invasion by the fish oil-based emulsion, the effects of prostaglandin (PG) E(2) and PGE(3) on invasion were examined. Pretreatment with the fish oil-based emulsion reduced invasiveness without affecting growth compared with the safflower oil-based emulsion. Pretreatment with the sera from rats infused with the fish oil-based emulsion also reduced invasiveness compared with the sera from rats infused with the safflower oil-based emulsion. The addition of PGE(2) eliminated the inhibitory effect of the fish oil-based emulsion, and the addition of PGE(3) reduced the invasiveness of hepatoma cells pretreated with the safflower oil-based emulsion. These results suggest that the fish oil-based emulsion may have anti-invasive effects. Changes in the membranous fatty acid composition and consequent changes in the prostaglandins produced may be involved in this inhibitory effect.

Recovery and treatment of uranium from uranium-containing solution by liquid membrane emulsion technology

International Nuclear Information System (INIS)

Xia Liangshu; Zhou Yantong; Xiao Yiqun; Peng Anguo; Xiao Jingshui; Chen Wei

2014-01-01

The recovery and treatment of uranium from uranium-containing solution using liquid membrane emulsion (LME) technology were studied in this paper, which contained the best volume ratio of membrane materials, stirring speed during emulsion process, the conditions of extracting, such as temperature, pH, initial concentration of uranium. Moreover, the mechanism for extracting uranium was also discussed. The best experimental conditions of emulsifying were acquired. The volume fractions of P 204 and liquid paraffin are 0.1 and 0.05, the volume ratios of Span80 and sulphonated kerosene to P 204 are 0.06 and 0.79 respectively, stirring speed is controlled in 2 000 r/min, and the concentration of inner phase is 4 mol/L. The recovery rate of uranium is up to 99% through the LME extracted uranium for 0.5 h at pH 2.5 and room temperature when the initial concentration is less than 400 mg/L and the volume ratio is 5 between the uranium-containing waste water and LME. The calculation results of Gibbs free energy show that the reaction process is spontaneous. (authors)

Use of micro-emulsions in liquid-liquid extraction

International Nuclear Information System (INIS)

Komornicki, Jacques

1982-01-01

As liquid-liquid extraction of metallic cations is an important method of separation and concentration of metals present in diluted aqueous solutions, and as the extraction rate is limited by one or several steps of matter transfer at the liquid-liquid interface, the extraction kinetics can be improved by creating a wide surface interface and by allowing an increased reactivity between species. In this research thesis, the author aims at determining to which extent systems of interface with a wide surface obtained by using for example amphiphile molecules to create micro-emulsions, can be used as reaction media for physical-chemical processes of liquid-liquid extraction. He also aims at identifying their applicability limitations and problems which might arise with their application. The author notably focuses of the liquid-liquid extraction of metallic cations exhibiting particularly slow extraction kinetics

Stability of bisphenol A (BPA) in oil-in water emulsions under riboflavin photosensitization.

Science.gov (United States)

Jang, Eun Yeong; Park, Chan Uk; Kim, Mi-Ja; Lee, JaeHwan

2012-08-01

Effects of riboflavin photosensitization on the degradation of bisphenol A (BPA) were determined in oil-in-water (O/W) emulsions containing ethylenediaminetetraacetic acid (EDTA) or sodium azide, which are a metal chelator or a singlet oxygen quencher, respectively. Also, the distribution of BPA between the continuous and dispersed phases in O/W emulsions was analyzed by high-performance liquid chromatography (HPLC). The concentration of BPA in O/W emulsions significantly decreased by 38.6% after 2 h under visible light irradiation and in the presence of riboflavin (P riboflavin photosensitization (P riboflavin photodegradation in O/W emulsions. Concentration of BPA, an endocrine disrupting chemical, was decreased significantly in oil-in-water emulsions under riboflavin and visible light irradiation. BPA in continuous aqueous phase was major target of riboflavin photosensitization. However, BPA was distributed more densely in lipid phase and more protected from riboflavin photosensitized O/W emulsions. This study can help to decrease the level of BPA in foods made of O/W emulsions containing riboflavin, which could be displayed under visible light irradiation. © 2012 Institute of Food Technologists®

Solvent-free formation of hydroxyapatite coated biodegradable particles via nanoparticle-stabilized emulsion route

International Nuclear Information System (INIS)

Okada, Masahiro; Fujii, Syuji; Nishimura, Taiki; Nakamura, Yoshinobu; Takeda, Shoji; Furuzono, Tsutomu

2012-01-01

Highlights: ► Hydroxyapatite (HAp) nanoparticles stabilized polymer melt-in-water emulsions without any molecular surfactants. ► Interaction between polymer and HAp played a crucial role. ► HAp-coated polymer particles were obtained from the emulsions without any organic solvents. - Abstract: Hydroxyapatite (HAp) nanoparticle-coated biodegradable polymer particles were fabricated from a nanoparticle-stabilized emulsion in the absence of any molecular surfactants or organic solvents. First, a polymer melt-in-water emulsion was prepared by mixing a water phase containing nanosized HAp particles as a particulate emulsifier and an oil phase consisting of poly(ε-caprolactone) (PCL) or poly(L-lactide-co-ε-caprolactone) (P(LLA-CL)) above its melting point. It was clarified that the interaction between ester/carboxyl groups of the polymers and the HAp nanoparticles at the polymer–water interface played a crucial role to prepare the nanoparticle-stabilized emulsion. The HAp nanoparticle-coated biodegradable polymer particle (a polymer solid-in-water emulsion) was fabricated by cooling the emulsion. The particle morphology and particle size were evaluated using scanning electron microscope.

Demulsification based on the thermal treatment (cooling and heating of W/O emulsions

Directory of Open Access Journals (Sweden)

Rajaković Vladana N.

2004-01-01

Full Text Available An important step in waste water treatment is the removal of oil from an O/W emulsion and the separation of oil and water into two phases, a process usually called demulsification. Modern methods of oil removal from waste water were described in the present study. Typical demulsification techniques include thermal, electrical, chemical, acoustic, or mechanical methods of emulsion treatment. The freeze/thaw process was found to be very effective for demulsification. In the freeze/thaw process, water removal from the W/O emulsion depends on the initial oil content, freezing temperature, freezing time, thawing rate and temperature. The described method is a non-destructive and physical method of emulsion treatment and because there is no addition of chemical agents there is no problem of further waste water treatment, which usually exists when chemicals are applied for demulsification. Different methods for oil content determination in the O/W emulsion were also applied and compared in this study (gravimetric, volumetric, measurement of oxygen consumption and emulsion pH, IR analysis of the emulsion, electro analytical measurement.

Pickering emulsions stabilized by whey protein nanoparticles prepared by thermal cross-linking

NARCIS (Netherlands)

Wu, Jiande; Shi, Mengxuan; Li, Wei; Zhao, Luhai; Wang, Ze; Yan, Xinzhong; Norde, Willem; Li, Yuan

2015-01-01

A Pickering (o/w) emulsion was formed and stabilized by whey protein isolate nanoparticles (WPI NPs). Those WPI NPs were prepared by thermal cross-linking of denatured WPI proteins within w/o emulsion droplets at 80. °C for 15. min. During heating of w/o emulsions containing 10% (w/v) WPI

British patent 580,504 and Ilford nuclear emulsions

International Nuclear Information System (INIS)

Waller, C.

1988-01-01

By a new technique disclosed in British Patent 580,504, gelatin with silver halide is precipitated from emulsion by adding a surface active agent. This technique was used from 1945 to produce emulsions with about eight times the normal ratio of silver halide to gelatin. The technique also facilitated the combined use of production and laboratory resources for their reliable manufacture on a fairly large scale. (author)

Time stamp technique using a nuclear emulsion multi-stage shifter for gamma-ray telescope

International Nuclear Information System (INIS)

Takahashi, Satoru; Aoki, Shigeki; Rokujo, Hiroki; Hamada, Kaname; Komatsu, Masahiro; Morishima, Kunihiro; Nakamura, Mitsuhiro; Nakano, Toshiyuki; Niwa, Kimio; Sato, Osamu; Yoshioka, Teppei; Kodama, Koichi

2010-01-01

Nuclear emulsion has a potential use as a gamma-ray telescope with high angular resolution. For this application it is necessary to know the time when each track was recorded in the emulsion. In previous experiments using nuclear emulsion, various efforts were used to associate time to nuclear emulsion tracks and to improve the time resolution. Using a high speed readout system for nuclear emulsion together with a clock-based multi-stage emulsion shifter, we invented a technique to give a time-stamp to emulsion tracks and greatly improve the time resolution. A test experiment with a 2-stage shifter was used to demonstrate the principle of multi-stage shifting, and we achieved a time resolution 1.5 s for 12.1 h (about 1 part in 29 000) with the time stamp reliability 97% and the time stamp efficiency 98%. This multi-stage shifter can achieve the time resolution required for a gamma-ray telescope and can also be applied to another cosmic ray observations and accelerator experiments using nuclear emulsion.

pH-induced inversion of water-in-oil emulsions to oil-in-water high internal phase emulsions (HIPEs) using core cross-linked star (CCS) polymer as interfacial stabilizer.

Science.gov (United States)

Chen, Qijing; Deng, Xiaoyong; An, Zesheng

2014-06-01

A pH-responsive core cross-linked star (CCS) polymer containing poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA) arms was used as an interfacial stabilizer for emulsions containing toluene (80 v%) and water (20 v%). In the pH range of 12.1-9.3, ordinary water-in-oil emulsions were formed. Intermediate multiple emulsions of oil-in-water-in-oil and water-in-oil-in-water were formed at pH 8.6 and 7.5, respectively. Further lowering the pH resulted in the formation of gelled high internal phase emulsions of oil-in-water type in the pH range of 6.4-0.6. The emulsion behavior was correlated with interfacial tension, conductivity and configuration of the CCS polymer at different pH. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The development of polyurethane modified bitumen emulsions for cold mix applications

OpenAIRE

Carrera Páez, Virginia; Cuadri Vega, Antonio Abad; García Morales, Moisés; Partal López, Pedro

2015-01-01

Bitumen emulsions stand for an alternative paving practice to the traditional hot-mix asphalts. In addition, modified bitumen emulsions show a better performance than unmodified ones. This work studies the feasibility of obtaining polyurethane modified bitumen emulsions, in which an isocyanate-functionalized polyol constitutes the bitumen modifier (in varying concentration from 1 to 4 wt.%). Storage stability and high in-service performance are evaluated by means of evolution of droplet size ...

Synthesis of nanocrystalline CeO2 particles by different emulsion methods

International Nuclear Information System (INIS)

Supakanapitak, Sunisa; Boonamnuayvitaya, Virote; Jarudilokkul, Somnuk

2012-01-01

Cerium oxide nanoparticles were synthesized using three different methods of emulsion: (1) reversed micelle (RM); (2) emulsion liquid membrane (ELM); and (3) colloidal emulsion aphrons (CEAs). Ammonium cerium nitrate and polyoxyethylene-4-lauryl ether (PE4LE) were used as cerium and surfactant sources in this study. The powder was calcined at 500 °C to obtain CeO 2 . The effect of the preparation procedure on the particle size, surface area, and the morphology of the prepared powders were investigated. The obtained powders are highly crystalline, and nearly spherical in shape. The average particle size and the specific surface area of the powders from the three methods were in the range of 4–10 nm and 5.32–145.73 m 2 /g, respectively. The CeO 2 powders synthesized by the CEAs are the smallest average particle size, and the highest surface area. Finally, the CeO 2 prepared by the CEAs using different cerium sources and surfactant types were studied. It was found that the surface tensions of cerium solution and the type of surfactant affect the particle size of CeO 2 . - Graphical Abstract: The emulsion droplet size distribution and the TEM images of CeO 2 prepared by different methods: reversed micelle (RM), emulsion liquid membrane (ELM) and colloidal emulsion aphrons (CEAs). Highlights: ► Nano-sized CeO 2 was successfully prepared by three different emulsion methods. ► The colloidal emulsion aphrons method producing CeO 2 with the highest surface area. ► The surface tensions of a cerium solution have slightly effect on the particle size. ► The size control could be interpreted in terms of the adsorption of the surfactant.

Zero-Valent Metal Emulsion for Reductive Dehalogenation of DNAPLs

Science.gov (United States)

Reinhart, Debra R. (Inventor); Clausen, Christian (Inventor); Gelger, Cherie L. (Inventor); Quinn, Jacqueline (Inventor); Brooks, Kathleen (Inventor)

2006-01-01

A zero-valent metal emulsion is used to dehalogenate solvents, such as pooled dense non-aqueous phase liquids (DNAPLs), including trichloroethylene (TCE). The zero-valent metal emulsion contains zero-valent metal particles, a surfactant, oil and water, The preferred zero-valent metal particles are nanoscale and microscale zero-valent iron particles.

An alkyl polyglucoside-mixed emulsifier as stabilizer of emulsion systems: the influence of colloidal structure on emulsions skin hydration potential.

Science.gov (United States)

Savic, Snezana; Lukic, Milica; Jaksic, Ivana; Reichl, Stephan; Tamburic, Slobodanka; Müller-Goymann, Christel

2011-06-01

To be considered as a suitable vehicle for drugs/cosmetic actives, an emulsion system should have a number of desirable properties mainly dependent on surfactant used for its stabilization. In the current study, C(12-14) alkyl polyglucoside (APG)-mixed emulsifier of natural origin has been investigated in a series of binary (emulsifier concentration 10-25% (w/w)) and ternary systems with fixed emulsifier content (15% (w/w)) with or without glycerol. To elucidate the systems' colloidal structure the following physicochemical techniques were employed: polarization and transmission electron microscopy, X-ray diffraction (WAXD and SAXD), thermal analysis (DSC and TGA), complex rheological, pH, and conductivity measurements. Additionally, the emulsion vehicles' skin hydration potential was tested in vivo, on human skin under occlusion. In a series of binary systems with fixed emulsifier/water ratios ranging from 10/90 to 25/75 the predominance of a lamellar mesophase was found, changing its character from a liquid crystalline to a gel crystalline type. The same was observed in gel emulsions containing equal amounts of emulsifier and oil (15% (w/w)), but varying in glycerol content (0-25%). Different emulsion samples exhibited different water distribution modes in the structure, reflecting their rheological behavior and also their skin hydration capacity. Copyright © 2011 Elsevier Inc. All rights reserved.

Evaluation of Soybean–Navy Bean Emulsions Using Different Processing Technologies

Directory of Open Access Journals (Sweden)

Sean X. Liu

2017-05-01

Full Text Available In this study, an innovative emulsion made from soybean and navy bean blends of different proportionalities was developed. In addition, two processing methods were used: traditional cooking and jet-cooking. The physical attributes and storage stability were measured and compared. This study found that the high content of starch and fiber in navy bean flour contributes to the increase in viscosity of the emulsions, at both room and refrigeration temperatures, as the proportion of navy bean flour in the blends increased. The steam jet-cooked emulsions with higher soybean content has better shelf life stability, smaller particle size, higher fat, lower starch, and lower viscosity, whereas the traditional kettle cooking method is better in reducing anti-nutritional components. No significant difference was found between the two cooking methods in terms of nutritional contents in the emulsions, such as protein, crude fat, and total starch. The traditional kettle cooking, with its longer cooking time, seems to reduce more trypsin inhibitor in the emulsions than those prepared with the steam jet-cooking. This exploratory study is the first to report soybean–navy bean beverage prototypes having desirable nutritional value and the potential for functional beverage market.

Emulsion Inks for 3D Printing of High Porosity Materials.

Science.gov (United States)

Sears, Nicholas A; Dhavalikar, Prachi S; Cosgriff-Hernandez, Elizabeth M

2016-08-01

Photocurable emulsion inks for use with solid freeform fabrication (SFF) to generate constructs with hierarchical porosity are presented. A high internal phase emulsion (HIPE) templating technique was utilized to prepare water-in-oil emulsions from a hydrophobic photopolymer, surfactant, and water. These HIPEs displayed strong shear thinning behavior that permitted layer-by-layer deposition into complex shapes and adequately high viscosity at low shear for shape retention after extrusion. Each layer was actively polymerized with an ultraviolet cure-on-dispense (CoD) technique and compositions with sufficient viscosity were able to produce tall, complex scaffolds with an internal lattice structure and microscale porosity. Evaluation of the rheological and cure properties indicated that the viscosity and cure rate both played an important role in print fidelity. These 3D printed polyHIPE constructs benefit from the tunable pore structure of emulsion templated material and the designed architecture of 3D printing. As such, these emulsion inks can be used to create ultra high porosity constructs with complex geometries and internal lattice structures not possible with traditional manufacturing techniques. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Demulsification of crude oil-in-water emulsions by means of fungal spores.

Directory of Open Access Journals (Sweden)

Alba Adriana Vallejo-Cardona

Full Text Available The present feature describes for the first time the application of spores from Aspergillus sp. IMPMS7 to break out crude oil-in-water emulsions (O/W. The fungal spores were isolated from marine sediments polluted with petroleum hydrocarbons. The spores exhibited the ability to destabilize different O/W emulsions prepared with medium, heavy or extra-heavy Mexican crude oils with specific gravities between 10.1 and 21.2°API. The isolated fungal spores showed a high hydrophobic power of 89.3 ± 1.9% and with 2 g of spores per liter of emulsion, the half-life for emulsion destabilization was roughly 3.5 and 0.7 h for extra-heavy and medium crude oil, respectively. Then, the kinetics of water separation and the breaking of the O/W emulsion prepared with heavy oil through a spectrofluorometric technique were studied. A decrease in the fluorescence ratio at 339 and 326 nm (I339/I326 was observed in emulsions treated with spores, which is similar to previously reported results using chemical demulsifiers.

Metallocene-catalyzed ethylene−α-olefin isomeric copolymerization: A perspective from hydrodynamic boundary layer mass transfer and design of MAO anion

KAUST Repository

Adamu, Sagir; Atiqullah, Muhammad; Malaibari, Zuhair O.; Al-Harthi, Mamdouh A.; Emwas, Abdul-Hamid M.; Ul-Hamid, Anwar

2015-01-01

-catalyzed ethylene polymerization. This approach was illustrated by conducting homo- and isomeric copolymerization of ethylene with 1-hexene and 4-methyl-1-pentene in the presence of bis(n-butylcyclopentadienyl) zirconium dichloride (nBuCp)2ZrCl2, using (i) MAO anion

Further study of helium production at large impact parameters in 6.4 TeV 32S emulsion reactions

International Nuclear Information System (INIS)

Kamel, S.

1999-01-01

Further study of helium production in electromagnetic and inelastic peripheral interactions of 32 S nuclei at 200 AGeV in nuclear emulsion is presented. The multiplicities, transverse momentum distributions of relativistic He fragments, and their parameters in both interactions are measured. The effect of the multiple helium production on the present obtained evidence of two different temperatures is investigated. The main characteristics of transverse momentum distributions show a certain dependence on the peripherality degree of the interactions

Characteristics of W/O emulsions containing polymeric emulsifier PEG 30-dipolyhydroxystearate

Directory of Open Access Journals (Sweden)

Milinković Jelena R.

2016-01-01

Full Text Available Water-in-oil (W/O emulsions are dispersed systems which are often used in the pharmaceutical, cosmetic and food industries as products, or as carriers of active substances. It is well known that they are very unstable, so that selection of the emulsifier and properties of the oil and water phase are main factors affecting their stability. The aim of this paper was to examine the possibility of application of a lipophilic, polymeric emulsifier, PEG 30-dipolyhydroxystearate (CithrolTM DPHS, for stabilization of W/O emulsions. Behaviour of the emulsifier at W/O interfaces was determined by means of tensiometry. A series of emulsions were prepared with 20% (w/w of water and different types of oil. Droplet size, droplet size distribution, viscosity, and sedimentation stability during 30 days of storage at room temperature of the emulsions prepared with paraffin oil, olive oil, grape seed oil, and medium-chain triglycerides, stabilized with 1% CithrolTM DPHS, were determined. All investigated emulsions were stable for 30 days, except the one prepared with paraffin oil. The results of this study confirmed that PEG 30-dipolyhydroxylstearate is a good emulsifier and stabilizer of W/O emulsions which contain different types of oil. [Projekat Ministarstva nauke Republike Srbije, br. III46010

Pickering emulsions for skin decontamination.

Science.gov (United States)

Salerno, Alicia; Bolzinger, Marie-Alexandrine; Rolland, Pauline; Chevalier, Yves; Josse, Denis; Briançon, Stéphanie

2016-08-01

This study aimed at developing innovative systems for skin decontamination. Pickering emulsions, i.e. solid-stabilized emulsions, containing silica (S-PE) or Fuller's earth (FE-PE) were formulated. Their efficiency for skin decontamination was evaluated, in vitro, 45min after an exposure to VX, one of the most highly toxic chemical warfare agents. Pickering emulsions were compared to FE (FE-W) and silica (S-W) aqueous suspensions. PE containing an oil with a similar hydrophobicity to VX should promote its extraction. All the formulations reduced significantly the amount of VX quantified on and into the skin compared to the control. Wiping the skin surface with a pad already allowed removing more than half of VX. FE-W was the less efficient (85% of VX removed). The other formulations (FE-PE, S-PE and S-W) resulted in more than 90% of the quantity of VX removed. The charge of particles was the most influential factor. The low pH of formulations containing silica favored electrostatic interactions of VX with particles explaining the better elimination from the skin surface. Formulations containing FE had basic pH, and weak interactions with VX did not improve the skin decontamination. However, these low interactions between VX and FE promote the transfer of VX into the oil droplets in the FE-PE. Copyright © 2016 Elsevier B.V. All rights reserved.

Performance, emissions and lubricant oil analysis of diesel engine running on emulsion fuel

International Nuclear Information System (INIS)

Hasannuddin, A.K.; Wira, J.Y.; Sarah, S.; Wan Syaidatul Aqma, W.M.N.; Abdul Hadi, A.R.; Hirofumi, N.; Aizam, S.A.; Aiman, M.A.B.; Watanabe, S.; Ahmad, M.I.; Azrin, M.A.

2016-01-01

Highlights: • The rate of NO x and PM reduction was lower than the rate of CO increase when using emulsion fuel. • The lubricant oil viscosity variation did not exceed the limits during the engine operation. • Emulsion fuel offers beneficial properties in terms of lower wear and friction. • Average depletions of lubricant oil additives were found at the lowest level for emulsion fuel in compared with D2. - Abstract: Emulsion fuel is one of the alternative fuels for diesel engines which are well-known for simultaneous reduction of Particulate Matter (PM) and Nitrogen Oxides (NO x ) emissions. However lack of studies have been conducted to investigate the effect of emulsion fuel usage for long run. Therefore, this study aims to investigate the effect of lubricant oil in diesel engine that operated using emulsion fuels for 200 h in comparison with Malaysian conventional diesel fuel (D2). Two emulsion fuels were used in the experiment comprising of water, low grade diesel fuel and surfactant; with ratio of 10:89:1 v/v% (E10) and 20:79:1 v/v% (E20). Engine tests were focused on fuel consumption, NO x , PM, Carbon Monoxide (CO), Carbon Dioxide (CO 2 ), Oxygen (O 2 ) and exhaust temperature. Parameters for the lubricant oil analysis measured were included kinematic viscosity, Total Acid Number (TAN), ash, water content, flash point, soot, wear metals and additive elements. The findings showed the fuel consumption were up to 33.33% (including water) and lower 9.57% (without water) using emulsion. The NO x and PM were reduced by 51% and 14% respectively by using emulsion fuel. Kinematic viscosity, TAN, ash, water content, flash point and soot for emulsion fuel were observed to be better or no changes in comparison to D2. The emulsion fuel did not cause any excessive amount of metals or degraded the additive. The average percentage of wear debris concentration reduction by emulsion fuel were 8.2%, 9.1%, 16.3% and 21.0% for Iron (Fe) Aluminum (Al), Copper (Cu) and

Effect of reaction conditions on film morphology of polyaniline composite membranes for gas separation

KAUST Repository

Blinova, Natalia V.; Stejskal, Jaroslav; Frechet, Jean; Švec, František

2012-01-01

precipitation, dispersion, or emulsion polymerization of aniline with simultaneous deposition on top of the porous polypropylene support, which was immersed in the reaction mixture. Variables such as temperature, concentration of reagents, presence of steric

Variation Of The Effects Of Adopol EVS-9279X On The Emulsion ...

African Journals Online (AJOL)

The effects of Adopol EVS-9279X on the emulsion and film properties of emulsion paint using 5%-10% w/w sample formulations have been examined. Variation of these effects with time was investigated in this study using the same 5%-10% w/w sample formulations. The emulsion and film properties were measured at four ...

High-conversion emulsion polymerization

NARCIS (Netherlands)

Maxwell, I.A.; Verdurmen, E.M.F.J.; German, A.L.

1992-01-01

The four important factors that det. the rate of emulsion polymn. are the propagation rate coeff., the latex-particle concn., the monomer concn. in the latex particles, and the free-radical concn. in the latex particles. Both theor. considerations and exptl. evidence suggested that the important

Tannin-based monoliths from emulsion-templating

International Nuclear Information System (INIS)

Szczurek, A.; Martinez de Yuso, A.; Fierro, V.; Pizzi, A.; Celzard, A.

2015-01-01

Highlights: • Efficient preparation procedures are presented for new and “green” tannin-based organic polyHIPEs. • Highest homogeneity and strength are obtained at an oil fraction near the close-packing value. • Structural and mechanical properties abruptly change above such critical value. - Abstract: Highly porous monoliths prepared by emulsion-templating, frequently called polymerised High Internal Phase Emulsions (polyHIPEs) in the literature, were prepared from “green” precursors such as Mimosa bark extract, sunflower oil and ethoxylated castor oil. Various oil fractions, ranging from 43 to 80 vol.%, were used and shown to have a dramatic impact on the resultant porous structure. A critical oil fraction around 70 vol.% was found to exist, close to the theoretical values of 64% and 74% for random and compact sphere packing, respectively, at which the properties of both emulsions and derived porous monoliths changed. Such change of behaviour was observed by many different techniques such as viscosity, electron microscopy, mercury intrusion, and mechanical studies. We show and explain why this critical oil fraction is the one leading to the strongest and most homogeneous porous monoliths

Parameters Effect on Productivity

Directory of Open Access Journals (Sweden)

S. Ahmadjo

2010-12-01

Full Text Available Bis(indenylzirconium dichloride as a catalyst was synthesized using a modified method at the room temperature. Polymerization of ethylene and copolymerization of ethylene and propylene were carried out by this metallocene catalyst. Ethylene propylene (P/E feed ratios of 0.25, 0.5, 1, and 2 were employed into the copolymerization systems. Copolymerization conditions like cocatalyst/catalyst ratio, copolymerization temperature, feed ratio and the viscosity average molecular weight (Mv changing with copolymerization temperature were investigated. Higher ratio of [Al]/[Zr]=750:1 increased the activity of the catalyst. However, higher concentration of the cocatalyst slightly reduced the activity. Viscosity-average molecular weight of polymer decreased with high ratio of [Al]/[Zr]. The highest activity was obtained at 60oC. Increases in copolymerization temperature decreased the viscosity-average molecular weight and ethylene content of the polymeric products. Increases in propylene content of the feed ratio producedamorphous polymers with products of increased glass transition temperatures.Kinetic reaction displayed a decay type of reaction.

Separation Properties of Wastewater Containing O/W Emulsion Using Ceramic Microfiltration/Ultrafiltration (MF/UF Membranes

Directory of Open Access Journals (Sweden)

Kanji Matsumoto

2013-06-01

Full Text Available Washing systems using water soluble detergent are used in electrical and mechanical industries and the wastewater containing O/W emulsion are discharged from these systems. Membrane filtration has large potential for the efficient separation of O/W emulsion for reuses of treated water and detergent. The separation properties of O/W emulsions by cross-flow microfiltration and ultrafiltration were studied with ceramic MF and UF membranes. The effects of pore size; applied pressure; cross-flow velocity; and detergent concentration on rejection of O/W emulsion and flux were systematically studied. At the condition achieving complete separation of O/W emulsion the pressure-independent flux was observed and this flux behavior was explained by gel-polarization model. The O/W emulsion tended to permeate through the membrane at the conditions of larger pore size; higher emulsion concentration; and higher pressure. The O/W emulsion could permeate the membrane pore structure by destruction or deformation. These results imply the stability of O/W emulsion in the gel-layer formed on membrane surface play an important role in the separation properties. The O/W emulsion was concentrated by batch cross-flow concentration filtration and the flux decline during the concentration filtration was explained by the gel- polarization model.

Separation Properties of Wastewater Containing O/W Emulsion Using Ceramic Microfiltration/Ultrafiltration (MF/UF) Membranes

Science.gov (United States)

Nakamura, Kazuho; Matsumoto, Kanji

2013-01-01

Washing systems using water soluble detergent are used in electrical and mechanical industries and the wastewater containing O/W emulsion are discharged from these systems. Membrane filtration has large potential for the efficient separation of O/W emulsion for reuses of treated water and detergent. The separation properties of O/W emulsions by cross-flow microfiltration and ultrafiltration were studied with ceramic MF and UF membranes. The effects of pore size; applied pressure; cross-flow velocity; and detergent concentration on rejection of O/W emulsion and flux were systematically studied. At the condition achieving complete separation of O/W emulsion the pressure-independent flux was observed and this flux behavior was explained by gel-polarization model. The O/W emulsion tended to permeate through the membrane at the conditions of larger pore size; higher emulsion concentration; and higher pressure. The O/W emulsion could permeate the membrane pore structure by destruction or deformation. These results imply the stability of O/W emulsion in the gel-layer formed on membrane surface play an important role in the separation properties. The O/W emulsion was concentrated by batch cross-flow concentration filtration and the flux decline during the concentration filtration was explained by the gel- polarization model. PMID:24958621

Radiation induced emulsion polymerization

International Nuclear Information System (INIS)

Stannett, V.T.; Stahel, E.P.

1990-01-01

High energy radiation is particularly favored for the initiation of emulsion polymerization. The yield of free radicals, for example, from the radiolysis of the aqueous phase, is high; G(radical) values of 5-7. In addition, the rather special kinetics associated with emulsion polymerization lead, in general, to very large kinetic chain lengths, even with 'non-ideal' monomers such as vinyl acetate. Together, high polymerization rates at low doses become possible. There are some important advantages of radiation polymerization compared with chemical initiators, such as potassium persulfate. Perhaps the most important among them is the temperature independence of the initiation step. This makes low temperature polymerization very accessible. With monomers such as vinyl acetate, where chain termination to monomer is predominant, low temperatures lead to often highly desirable higher molecular weights. With styrene, the classical ideally behaved monomer, there are the advantages such as, for example, the feasibility of using cationic monomers. These and some attendant disadvantages are discussed in detail, including pilot plant studies

Heavy Hyperfragments produced by 800 MeV/c k in Nuclear Emulsions

International Nuclear Information System (INIS)

Marcial, P.

1967-01-01

A statistical and phenomenological survey of nearly 1200 heavy hyperfragments produced by interaction of 800 MeV/c K with the heavy nuclei of llford K 5 emulsion is presented. The emulsion was exposed A statistical and phenomenological survey of nearly 1200 heavy hyperfragments produced by interaction of 800 MeV/c K tilde with the heavy nuclei of llford K5 emulsion is presented. The emulsion was exposed in Berkeley. The variation of long list of parameters dealing with both the production and desintegration of the hyperfragments, with the size of the primary interaction is given. (Author)

High-Surface-Area, Emulsion-Templated Carbon Foams by Activation of polyHIPEs Derived from Pickering Emulsions

Directory of Open Access Journals (Sweden)

Robert T. Woodward

2016-09-01

Full Text Available Carbon foams displaying hierarchical porosity and excellent surface areas of >1400 m2/g can be produced by the activation of macroporous poly(divinylbenzene. Poly(divinylbenzene was synthesized from the polymerization of the continuous, but minority, phase of a simple high internal phase Pickering emulsion. By the addition of KOH, chemical activation of the materials is induced during carbonization, producing Pickering-emulsion-templated carbon foams, or carboHIPEs, with tailorable macropore diameters and surface areas almost triple that of those previously reported. The retention of the customizable, macroporous open-cell structure of the poly(divinylbenzene precursor and the production of a large degree of microporosity during activation leads to tailorable carboHIPEs with excellent surface areas.

Tailoring Copolymer Properties by Gradual Changes in the Distribution of the Chains Composition Using Semicontinuous Emulsion Polymerization

Directory of Open Access Journals (Sweden)

Carlos Federico Jasso-Gastinel

2017-02-01

Full Text Available To design the properties of a copolymer using free radical polymerization, a semicontinuous process can be applied to vary the instantaneous copolymer composition along the conversion searching for a specific composition spectrum of copolymer chains, which can be termed as weight composition distribution (WCD of copolymer chains. Here, the styrene-n-butyl acrylate (S/BA system was polymerized by means of a semicontinuous emulsion process, varying the composition of the comonomer feed to obtain forced composition copolymers (FCCs. Five different feeding profiles were used, searching for a scheme to obtain chains rich in S (looking for considerable modulus, and chains rich in BA (looking for large deformation as a technique to achieve synergy in copolymer properties; the mechanostatic and dynamic characterization discloses the correspondence between WCD and the bulk properties. 1H-nuclear magnetic resonance (1H-NMR analysis enabled the determination of the cumulative copolymer composition characterization, required to estimate the WCD. The static test (stress-strain and dynamic mechanical analysis (DMA were performed following normed procedures. This is the first report that shows very diverse mechanostatic performances of copolymers obtained using the same chemical system and global comonomer composition, forming a comprehensive failure envelope, even though the tests were carried out at the same temperature and cross head speed. The principles for synergic performance can be applied to controlled radical copolymerization, designing the composition variation in individual molecules along the conversion.

Regulating Molecular Aggregations of Polymers via Ternary Copolymerization Strategy for Efficient Solar Cells.

Science.gov (United States)

Wang, Qian; Wang, Yingying; Zheng, Wei; Shahid, Bilal; Qiu, Meng; Wang, Di; Zhu, Dangqiang; Yang, Renqiang

2017-09-20

For many high-performance photovoltaic materials in polymer solar cells (PSCs), the active layers usually need to be spin-coated at high temperature due to the strong intermolecular aggregation of donor polymers, which is unfavorable in device repeatability and large-scale PSC printing. In this work, we adopted a ternary copolymerization strategy to regulate polymer solubility and molecular aggregation. A series of D-A 1 -D-A 2 random polymers based on different acceptors, strong electron-withdrawing unit ester substituted thieno[3,4-b]thiophene (TT-E), and highly planar dithiazole linked TT-E (DTzTT) were constructed to realize the regulation of molecular aggregation and simplification of device fabrication. The results showed that as the relative proportion of TT-E segment in the backbone increased, the absorption evidently red-shifted with a gradually decreased aggregation in solution, eventually leading to the active layers that can be fabricated at low temperature. Furthermore, due to the excellent phase separation and low recombination, the optimized solar cells based on the terpolymer P1 containing 30% of TT-E segment exhibit high power conversion efficiency (PCE) of 9.09% with a significantly enhanced fill factor up to 72.86%. Encouragingly, the photovoltaic performance is insensitive to the fabrication temperature of the active layer, and it still could maintain high PCE of 8.82%, even at room temperature. This work not only develops the highly efficient photovoltaic materials for low temperature processed PSCs through ternary copolymerization strategy but also preliminarily constructs the relationship between aggregation and photovoltaic performance.

Performance of single cylinder, direct injection Diesel engine using water fuel emulsions

International Nuclear Information System (INIS)

Abu-Zaid, M.

2004-01-01

A single cylinder Diesel engine study of water-in-Diesel emulsions was conducted to investigate the effect of water emulsification on the engine performance and gases exhaust temperature. Emulsified Diesel fuels of 0, 5, 10, 15 and 20 water/Diesel ratios by volume, were used in a single cylinder, direct injection Diesel engine, operating at 1200-3300 rpm. The results indicate that the addition of water in the form of emulsion improves combustion efficiency. The engine torque, power and brake thermal efficiency increase as the water percentage in the emulsion increases. The average increase in the brake thermal efficiency for 20% water emulsion is approximately 3.5% over the use of Diesel for the engine speed range studied. The proper brake specific fuel consumption and gases exhaust temperature decrease as the percentage of water in the emulsion increases

Effect of citronella essential oil fractions as oil phase on emulsion stability

Science.gov (United States)

Septiyanti, Melati; Meliana, Yenny; Agustian, Egi

2017-11-01

The emulsion system consists of water, oil and surfactant. In order to create stable emulsion system, the composition and formulation between water phase, surfactant and oil phase are very important. Essential oil such as citronella oil has been known as active ingredient which has ability as insect repellent. This research studied the effect of citronella oil and its fraction as oil phase on emulsion stability. The cycle stability test was conducted to check the emulsion stability and it was monitored by pH, density, viscosity, particle size, refractive index, zeta potential, physical appearance and FTIR for 4 weeks. Citronellal fraction has better stability compared to citronella oil and rhodinol fraction with slight change of physical and chemical properties before and after the cycle stability test. However, it is need further study to enhance the stability of the emulsion stability for this formulation.