WorldWideScience

Sample records for eletrodepositado como sensor

  1. Potencialidades do dióxido de chumbo eletrodepositado como sensor potenciométrico Potentialities of electrodeposited lead dioxide as a potentiometric sensor

    Directory of Open Access Journals (Sweden)

    Milton Duffles Capelato

    1998-07-01

    Full Text Available This paper proposes an experiment to be performed in both instrumental analysis and experimental physical-chemistry curricular disciplines in order to open options to develop challenging basic research activities. Thus the experimental procedures and the results obtained in the preparation of electrodeposited lead dioxide onto graphite and its evaluation as potentiometric sensor for H3O+ and Pb2+ ions, are presented. The data obtained in acid-base titrations were compared with those of the traditional combination glass electrode at the same conditions. Although a linear sub-Nernstian response to free hydrogen ions was observed for the electrodeposited PbO2 electrode, a good agreement was obtained between them. Working as lead(II sensing electrode, the PbO2 showed a linear sub-Nernstian behavior at total Pb2+ concentrations ranging from 3,5 x 10-4 to 3,0 x 10-2 mol/L in nitrate media. For the redox couple PbO2/Pb(II the operational slope converges to the theoretical one, as the acidity of the working solution increases.

  2. Caracterização de níquel eletrodepositado em substrato de cobre

    OpenAIRE

    Erik Luis Sardinha Cecconello

    2006-01-01

    As propriedades tribológicas de materiais de engenharia são melhoradas através do uso de revestimentos. Na indústria do aço, a aplicação de revestimentos de níquel em cobre tem propiciado um aumento na vida útil de moldes de lingotamento contínuo. O níquel eletrodepositado aumenta a resistência ao desgaste por abrasão e fricção entre o aço e o cobre utilizado nos moldes. O objetivo deste trabalho foi estudar a morfologia e determinar a porosidade do níquel eletrodepositado em cobre, utiliz...

  3. Receptores fluorogénicos como sensores para dicarboxilatos

    OpenAIRE

    Jiménez Jiménez, María Belén

    2011-01-01

    [ES]El desarrollo de receptores moleculares y quimiosensores para el reconocimiento de aniones es de gran importancia, debido al papel fundamental que desempeñan en muchos procesos químicos y biológicos así como en diagnósticos clínicos y análisis medioambientales. En este contexto, los aniones dicarboxilato resultan muy atractivos porque sus estructuras forman parte de algunas moléculas relevantes, participan en numerosos procesos metabólicos, como los ciclos del ácido cítrico y del glio...

  4. The silicon and their properties as sensor material; El silicio y sus propiedades como material sensor

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval-Ibarra, F. [Centro de Investigacion y de Estudios Avanzados-Unidad Guadalajara, Jalisco (Mexico)

    2001-04-01

    This paper focused on the design considerations of silicon based transducers. The reason for this is twofold. First of all, silicon is a suitable material for the development of fully integrated transducers, which can be manufactured with any IC fabrication process. The second reason is to describe the possibilities to design the so-called smart sensors. In this way, an overview has been created with the purpose to write a useful reference for the beginner and for the expert sensor designer. [Spanish] Este articulo describe las consideraciones de diseno de diversos transductores basados en silicio. El proposito es doble: 1) el silicio es un material semiconductor adecuado para el desarrollo de transductores completamente integrados, los cuales pueden ser fabricados con procesos de fabricacion estandar de circuitos integrados; 2) si el desarrollo de transductores es compatible con procesos de fabricacion estandar, entonces se describen las capacidades para el desarrollo de sensores integrantes. Por lo anterior, se realiza una revision bibliografica con la intencion de elaborar una referencia que sea util para el principiante y para el disenador de sensores de estado solido.

  5. Dióxido de estanho nanoestruturado como sensor de NOx Nanostructured tin dioxide as a NOx gas sensor

    Directory of Open Access Journals (Sweden)

    A. P. Maciel

    2003-09-01

    Full Text Available Neste trabalho, nanopartículas de SnO2 foram obtidas pelo método do precursor polimérico e caracterizadas por difração de raios X, isotermas de adsorção-dessorção, microscopia eletrônica de varredura e microscopia eletrônica de transmissão. Apenas a fase cassiterita (tetragonal foi observada. O material obtido apresenta com alta área superficial e porosidade. Estas características são pré-requisitos para um bom sensor de gás. A sensibilidade ao NOx para o SnO2 foi estudado na faixa de temperatura compreendida entre 200 e 500 ºC. Observou-se uma baixa sensibilidade entre 200 e 350 ºC, porém, a partir de 400 ºC ocorreu um aumento de três vezes na sensibilidade do sensor. A máxima sensibilidade ocorreu em 400 ºC, com um tempo de resposta de 730 s.In this work SnO2 nanoparticles were obtained by the polimeric precursor method and characterized by X-ray diffraction, gas adsorption and desorption isotherms, scanning electron microscopy and transmission electron microscopy. Only the cassiterite (tetragonal phase was observed. The obtained material presents a high surface area and high porosity. These characteristics are prerequisites for a good gas sensor. The NOx sensibility was studied in the temperature range between 200 and 500 °C. A low sensibility between 200 to 350 °C is also observed; however, starting from 400 °C, an increase of three times in the sensor sensibility occurs. The maximum sensibility was measured at 400 °C with a response time of 730 s.

  6. Estudo da origem do ferromagnetismo em filmes finos eletrodepositados de Céria Deficientes em Oxigênio

    OpenAIRE

    Fernandes, Vilmar

    2010-01-01

    Resumo: Neste trabalho é descrita a eletrodeposição de filmes finos de óxido de cério (CeO2) com espessuras entre 20 nm e 300 nm sobre substratos de silício. Os depósitos foram preparados usando o método potenciostático a partir de soluções aquosas contendo 800 mmol/L de CeCl3.7H2O com e sem a adição de peróxido de hidrogênio (H2O2) como agente oxidante. Análises de microscopia eletrônica de transmissão em modo de difração de área selecionada revelam que os depósitos possuem estrutura policri...

  7. Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, H. [PBI-Dansensor A/S (Denmark); Toft Soerensen, O. [Risoe National Lab., Materials Research Dept. (Denmark)

    1999-10-01

    A new type of ceramic oxygen sensors based on semiconducting oxides was developed in this project. The advantage of these sensors compared to standard ZrO{sub 2} sensors is that they do not require a reference gas and that they can be produced in small sizes. The sensor design and the techniques developed for production of these sensors are judged suitable by the participating industry for a niche production of a new generation of oxygen sensors. Materials research on new oxygen ion conducting conductors both for applications in oxygen sensors and in fuel was also performed in this project and finally a new process was developed for fabrication of ceramic tubes by dip-coating. (EHS)

  8. Sensors

    CERN Document Server

    Pigorsch, Enrico

    1997-01-01

    This is the 5th edition of the Metra Martech Directory "EUROPEAN CENTRES OF EXPERTISE - SENSORS." The entries represent a survey of European sensors development. The new edition contains 425 detailed profiles of companies and research institutions in 22 countries. This is reflected in the diversity of sensors development programmes described, from sensors for physical parameters to biosensors and intelligent sensor systems. We do not claim that all European organisations developing sensors are included, but this is a good cross section from an invited list of participants. If you see gaps or omissions, or would like your organisation to be included, please send details. The data base invites the formation of effective joint ventures by identifying and providing access to specific areas in which organisations offer collaboration. This issue is recognised to be of great importance and most entrants include details of collaboration offered and sought. We hope the directory on Sensors will help you to find the ri...

  9. Laser of optical fiber composed by two coupled cavities: application as optical fiber sensor; Laser de fibra optica compuesto por dos cavidades acopladas: aplicacion como sensor de fibra optica

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez S, R.A.; Kuzin, E.A.; Ibarra E, B. [Instituto Nacional de Astrofisica, Optica y Electronica (INAOE), A.P. 51 y 216, 72000 Puebla (Mexico); May A, M. [Universidad Autonoma del Carmen (UNACAR) Av. 56 No. 4 por Av. Concordia, Campeche (Mexico); Shlyagin, M.; Marquez B, I. [Centro de Investigacion Cientifica y de Ensenanza Superior de Ensenada (CICESE), 22860 Ensenada, Baja California (Mexico)]. e-mail: ravsa100@hotmail.com

    2004-07-01

    We show an optical fiber laser sensor which consist of two cavities coupled and three fiber Bragg gratings. We used one Bragg grating (called reference) and two Bragg gratings (called sensors), which have the lower reflection wavelength. The reference grating with the two sensors grating make two cavities: first one is the internal cavity which has 4230 m of length and the another one is the external cavity which has 4277 m of length. Measuring the laser beating frequency for a resonance cavity and moving the frequency peaks when the another cavity is put in resonance, we prove that the arrangement can be used as a two points sensor for determining the difference of temperature or stress between these two points. (Author)

  10. Modificação da fibra de coco com polianilina e o seu uso como sensor de pressão Coconut fibers modified with polyaniline nanoparticles are used in pressure sensor

    Directory of Open Access Journals (Sweden)

    Fernando G. de Souza Jr

    2011-01-01

    Full Text Available O presente trabalho teve por foco a modificação de fibras de coco, tornando-as materiais compósitos condutores de eletricidade. Para tanto, foi utilizada uma técnica de polimerização in situ, capaz de gerar nanopartículas de polianilina sobre a superfície de fibras tratadas. As fibras modificadas com polianilina foram caracterizadas por FTIR, UV-Vis, DRX e SAXS. Além disso, foram submetidas a ensaios eletromecânicos, com a finalidade de indicar quais condições de modificação são mais eficientes para a obtenção de um material sensível a esforços compressivos. Os resultados de sensibilidade a compressão sugerem que os materiais modificados com as menores quantidades de polianilina são os mais adequados para aplicações no campo de sensores de pressão de natureza resistiva, podendo ser utilizados no desenvolvimento de dispositivos inteligentes.Coconut fibers were covered with polyaniline in order to obtain electrically conductive composite materials. For this purpose aniline was polymerized in the presence of coconut fibers, leading to the formation of polyaniline nanoparticles over the surface of the fibers. The treated fibers were analyzed by FTIR, UV-Vis, DRX and SAXS, being also submitted to electromechanical assays, in order to find the best conditions for obtaining materials with optimal compressional sensitivity. The results suggest that materials obtained with smaller amounts of polyaniline are the most adequate for applications as resistive pressure sensors. This class of materials can be used in the development of intelligent devices.

  11. Polímeros luminescentes como sensores de radiação não ionizante: aplicação em fototerapia neonatal Luminescent polymers as sensor for non-ionizing radiation: neonatal phototherapy application

    Directory of Open Access Journals (Sweden)

    Cláudia K. B. de Vasconcelos

    2007-12-01

    Full Text Available Neste trabalho foram observadas mudanças nas propriedades de emissão e de absorção de soluções de poli[2-metoxi-5-(2’etil-hexiloxi-p-fenilenovinileno] - MEH-PPV com a exposição à radiação na região espectral do visível na faixa de 425 a 500 nm. Os resultados demonstram a possibilidade do uso de sistemas luminescentes como elemento ativo de detectores de radiação não ionizante, sobretudo na região empregada na profilaxia e no tratamento fototerápico da hiperbilirrubinemia neonatal.In this work, we observed changes in the emission and absorption properties of poly[(2-methoxy-5-hexyloxy-p-phenylenevinylene] - MEH-PPV solutions in the visible range from 425 to 500 nm. The main results demonstrated the possibility of using luminescent polymers as active material of non-ionizing radiation dosimeter, in such a way that MEH-PPV is promising for use in a management system to monitor radiation absorbed by newborns during phototherapy treatment of neonatal hyperbilirubinemia.

  12. Estágios iniciais da eletrodeposição de cobalto e níquel acompanhados por EC-STM e EC-AGFM

    OpenAIRE

    Carmem Rosane Isse Gomes

    2003-01-01

    Neste trabalho foram eletrodepositados filmes ultrafinos de cobalto e níquel sobre substrato de Au/mica. Os estágios iniciais da deposição foram acompanhados in-situ pelo uso das técnicas de EC-STM (microscopia de varredura por tunelamento – modo eletroquímico) e EC-AGFM (magnetome tria de força de gradiente de campo alternado – modo eletroquímico), que se constitui em uma nova técnica para avaliação de propriedades magnéticas de filmes ultrafinos eletrodepositados. Como resultado, foi obtido...

  13. TUBERCULOSIS COMO ENFERMEDAD OCUPACIONAL

    Science.gov (United States)

    Mendoza-Ticona, Alberto

    2014-01-01

    Existe evidencia suficiente para declarar a la tuberculosis como enfermedad ocupacional en diversos profesionales especialmente entre los trabajadores de salud. En el Perú están normados y reglamentados los derechos laborales inherentes a la tuberculosis como enfermedad ocupacional, como la cobertura por discapacidad temporal o permanente. Sin embargo, estos derechos aún no han sido suficientemente socializados. En este trabajo se presenta información sobre el riesgo de adquirir tuberculosis en el lugar de trabajo, se revisan las evidencias para declarar a la tuberculosis como enfermedad ocupacional en trabajadores de salud y se presenta la legislación peruana vigente al respecto. PMID:22858771

  14. Ambient Sensors

    NARCIS (Netherlands)

    Börner, Dirk; Specht, Marcus

    2014-01-01

    This software sketches comprise two custom-built ambient sensors, i.e. a noise and a movement sensor. Both sensors measure an ambient value and process the values to a color gradient (green > yellow > red). The sensors were built using the Processing 1.5.1 development environment. Available under

  15. El derecho como hecho o como norma

    Directory of Open Access Journals (Sweden)

    Roberto José Vernengo

    2015-10-01

    Full Text Available Para el historiador, antiguamente, y para el sociólogo, en nuestros días, el derecho es un fenómeno empírico. El derecho de una sociedad es un dato de su realidad: historiador o sociólogo tienen que buscar el derecho en alguna experiencia empírica accesible. Sin embargo, no es fácil toparse con el derecho de una sociedad, como, por caso, con el derecho argentino actual, pues no sabemos muy bien a qué datos de la realidad apuntar. Aquéllos que discernimos aparecen teñidos por alguna concepción previa que tengamos sobre qué haya de entenderse por derecho. (...

  16. A palavra como enigma

    Directory of Open Access Journals (Sweden)

    Yudith Rosenbaum

    2005-06-01

    Full Text Available Este estudo pretende analisar o conto “Famigerado”, de Guimarães Rosa, à luz das Formas Simples, de André Jolles, e da psicanálise. O texto é lido como uma adivinha às avessas, invertendo as posições do inquiridor e do questionado. Tendo como fundo a modernização do sertão nos anos 60, o embate entre o letrado e o jagunço revela tensões e ambigüidades, abordadas pela estilística e pela psicanálise.

  17. Development a solid state sensor based on SnO{sub 2} nanoparticles for underground coal mine methane detection using zeolites as filter; Desenvolvimento de sensor de estado solido com nanoparticulas de SnO{sub 2} para metano de mina de carvao subterranea utilizando zeolitas como filtro

    Energy Technology Data Exchange (ETDEWEB)

    Abruzzi, R.C.; Dedavid, B.A.; Pires, M.J.R.; Luvizon, N.S., E-mail: rafael.abruzzi@acad.pucrs.br [Pontificia Universidade Catolica do Rio Grande do Sul (PUCRS), Porto Alegre, RS (Brazil)

    2016-07-01

    Aiming the monitoring of methane (CH{sub 4}) in underground coal mines, the tin oxide (SnO{sub 2}) was synthesis and applied to the development of a MOS sensor (metal oxide semiconductor). Zeolite have been tested as a filter of carbon dioxide (CO{sub 2}) to ensure the selectivity in the detection of CH{sub 4}. Analysis of Transmission Electron Microscopy (TEM) and X-Ray Diffraction (XRD) indicated a synthesis of nanoscaled structures. The energy band gap showed characteristic values for a potential application of SnO{sub 2} in CH{sub 4} sensors. Analysis of surface area by BET isotherms showed high values for the zeolite 13X and Y, while adsorption tests indicated that the zeolite 13X presents greater adsorption efficiency of CO{sub 2}. The sputtering technique for deposition of the electrodes, as well as the method of drop coating for deposition of SnO{sub 2}, proved effective in developing the sensor. (author)

  18. Metamaterial Sensors

    Directory of Open Access Journals (Sweden)

    Jing Jing Yang

    2013-01-01

    Full Text Available Metamaterials have attracted a great deal of attention due to their intriguing properties, as well as the large potential applications for designing functional devices. In this paper, we review the current status of metamaterial sensors, with an emphasis on the evanescent wave amplification and the accompanying local field enhancement characteristics. Examples of the sensors are given to illustrate the principle and the performance of the metamaterial sensor. The paper concludes with an optimistic outlook regarding the future of metamaterial sensor.

  19. Sensor networks

    NARCIS (Netherlands)

    Chatterjea, Supriyo; Thurston, J.; Kininmonth, S.; Havinga, Paul J.M.

    2006-01-01

    This article describes the details of a sensor network that is currently being deployed at the Great Barrier Reef in Australia. The sensor network allows scientists to retrieve sensor data that has a high spatial and temporal resolution. We give an overview of the energy-efficient data aggregation

  20. Attention Sensor

    NARCIS (Netherlands)

    Börner, Dirk; Kalz, Marco; Specht, Marcus

    2014-01-01

    This software sketch was used in the context of an experiment for the PhD project “Ambient Learning Displays”. The sketch comprises a custom-built attention sensor. The sensor measured (during the experiment) whether a participant looked at and thus attended a public display. The sensor was built

  1. Los destinatarios como protagonistas

    Directory of Open Access Journals (Sweden)

    Sandra Massoni

    2015-01-01

    Full Text Available Trata sobre la comunicación como herramienta estratégica en el sistema agrícola del ámbito rural. La propuesta consiste en armar la estrategia de comunicación para defender y promover la solución de los problemas partir de cada uno de los sectores.

  2. Los destinatarios como protagonistas

    OpenAIRE

    Sandra Massoni

    2015-01-01

    Trata sobre la comunicación como herramienta estratégica en el sistema agrícola del ámbito rural. La propuesta consiste en armar la estrategia de comunicación para defender y promover la solución de los problemas partir de cada uno de los sectores.

  3. El libro como performance

    OpenAIRE

    Craig Epplin

    2015-01-01

    La comunidad poética Estación Pringles entabla un diálogo intrigante con el formato libro. Por una parte, su acercamiento teatral a la poesía parecería excluir la posibilidad de ver este medio como un modelo para el proyecto. Sin embargo, en su diálogo con la línea poética iniciada por Stéphane Mallarmé, esta iniciativa artística propone un concepto del libro como performance. Esta orientación es evidente, además, en la producción impresa de Estación Pringles. The poetry community Estación...

  4. Conducta social como intercambio

    Directory of Open Access Journals (Sweden)

    GERGE C. HOMANS

    1999-01-01

    Full Text Available En ¿Conducta Social como intercambio? : anotaciones a un texto clásico de un autor poco clásico (¿Social Behavior as Exchange? : Miguel Requena ofrece una introducción al español de la versión de Homans ?Social Behavior as Exchange? originariamente publicado en el American Journal of Sociology (1958, 63, May, 597-606.

  5. Y, croaba como rana

    OpenAIRE

    Diéguez Pinto, Marilyn

    2016-01-01

    Al término de los nueve meses de gestación, un día seis de un año seis, bajo el influjo de la luna llena, vino al mundo aquella criatura de andar endeble, piel rugosa en cuerpo grueso de bracitos cortos, con ojos saltones en cuencas anfibias. Cual fatal profecía, de un oráculo antiguo, el niño, al llorar, croaba como rana.

  6. O corpo como pulso

    Directory of Open Access Journals (Sweden)

    Flavia Liberman

    Full Text Available O corpo é foco de muitos estudos e intervenções. Alguns paradigmas o concebem apenas em seu aspecto sensório-motor, enquanto outros transitam prioritariamente por uma dimensão psicológica. Procurando contribuir para a formulação de outras perspectivas no campo, apresentam-se aspectos da concepção de corpo de Stanley Keleman em ressonância com os estudos de Regina Favre. A partir de cenas clínicas em grupos de seminários, podemos pensar o corpo como pulso, multimídia, multifacetado, que se (des constrói permanentemente nos encontros. Articulando experiências clínicas da autora como terapeuta ocupacional e docente da graduação e em grupos de estudos, essas concepções servem como guia para uma clínica pensada, construída e balizada pelo corpo mediante utilização de abordagens corporais para a promoção de encontros plasmados por afetos e acontecimentos, na tentativa de criar corpos que possam sustentar as intensidades vividas e permitam a observação de si, a aproximação com o outro e a produção de singularidades.

  7. O corpo como pulso

    Directory of Open Access Journals (Sweden)

    Flavia Liberman

    2010-06-01

    Full Text Available O corpo é foco de muitos estudos e intervenções. Alguns paradigmas o concebem apenas em seu aspecto sensório-motor, enquanto outros transitam prioritariamente por uma dimensão psicológica. Procurando contribuir para a formulação de outras perspectivas no campo, apresentam-se aspectos da concepção de corpo de Stanley Keleman em ressonância com os estudos de Regina Favre. A partir de cenas clínicas em grupos de seminários, podemos pensar o corpo como pulso, multimídia, multifacetado, que se (des constrói permanentemente nos encontros. Articulando experiências clínicas da autora como terapeuta ocupacional e docente da graduação e em grupos de estudos, essas concepções servem como guia para uma clínica pensada, construída e balizada pelo corpo mediante utilização de abordagens corporais para a promoção de encontros plasmados por afetos e acontecimentos, na tentativa de criar corpos que possam sustentar as intensidades vividas e permitam a observação de si, a aproximação com o outro e a produção de singularidades.

  8. Smart sensors

    Science.gov (United States)

    Corsi, Carlo

    2006-08-01

    The term "Smart Sensors" refer to sensors which contain both sensing and signal processing capabilities with objectives ranging from simple viewing to sophisticated remote sensing, surveillance, search/track, weapon guidance, robotics, perceptronics and intelligence applications. In a broad sense, they include any sensor systems covering the whole electromagnetic spectrum: this paper deals specifically with a new class of smart sensors in infrared spectral bands whose developments started some years ago, when it was recognized that the rapid advances of "very large scale integration" (VLSI) processor technology and mosaic infrared detector array technology could be combined to develop new generations of infrared smart sensor systems with much improved performance. So, sophisticated signal processing operations have been developed for these new systems by integrating microcomputers and other VLSI signal processors within or next to the sensor arrays on the same focal plane avoiding complex computing located far away from the sensors. Recently this approach is achieving higher goals by a new and revolutionary sensors concept which introduce inside the sensor some of the basic function of living eyes, such as dynamic stare, dishomogenity compensation, spatial and temporal filtering. New objectives and requirements of these new focal plane processors are presented for this type of new infrared smart sensor systems. This paper is concerned with the processing techniques for only the front end of the focal plane processing, namely, the enhancement of target-to-noise ratio by background clutter suppression and the improvement in target detection by "smart" and pattern correlation threshold.

  9. Study of the YBa{sub 2}Cu{sub 3}O-7{sub -{delta}} superconductor application as a low magnetic field sensor; Estudo da aplicacao do supercondutor YBa{sub 2}Cu{sub 3}O{sub 7-{delta}} como sensor de baixo campo magnetico

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, G.L; Shigue, C.Y.; Santos, C.A.M. dos; Machado, A.J. [Faculdade de Engenharia Quimica de Lorena (Faenquil), SP (Brazil). Dept. de Engenharia de Materiais

    2000-07-01

    It has been proposed in the literature a new regime for high critical temperature superconductors labeled as thermally activated flux flow (TAFF). This regime presents a state in which vortex dynamic exhibit a ohmic behavior. The resistivity in this regime is proportional to the applied magnetic field for small current densities. Materials showing this behavior have high disordering and present semiconductor behavior in normal state with broad transition temperature. In this work is presented a systematic study of the magnetoresistance as a function of the applied magnetic field for polycrystalline samples with several thickness. Results of X ray diffraction, resistivity as a function of the temperature, I-V characteristic curves and magnetoresistance are showed. Finally is proposed a calibration curve of the magnetoresistance as a function of the magnetic field, that show the possibility of its use as magnetic field sensor. (author)

  10. Gas Sensor

    KAUST Repository

    Luebke, Ryan

    2015-01-22

    A gas sensor using a metal organic framework material can be fully integrated with related circuitry on a single substrate. In an on-chip application, the gas sensor can result in an area-efficient fully integrated gas sensor solution. In one aspect, a gas sensor can include a first gas sensing region including a first pair of electrodes, and a first gas sensitive material proximate to the first pair of electrodes, wherein the first gas sensitive material includes a first metal organic framework material.

  11. COMO? PALETAS MEXICANAS BRASILEIRAS?

    Directory of Open Access Journals (Sweden)

    Daniela Maria Alves Chaud

    2016-03-01

    Full Text Available As informações sobre alimentação estão mais acessíveis e democráticas. As tendências alimentares são inspiradas por diversos fatores, mas sempre estão associados à moda, mídia e como forma de conjectura de um estilo de vida. Há pouco tempo, as grandes cidades brasileiras foram invadidas por uma nova mania: as paletas mexicanas, que, na verdade, não são “tão mexicanas”. Esses sorvetes apresentam qualidades organolépticas marcantes, em virtude, entre outros fatores, ao alto teor de açúcar e, em alguns casos, de gorduras. A concepção gourmetizada e natural dessa iguaria, seu custo e as propriedades nutricionais são peculiares e, aparentemente, um modismo. Esse trabalho teve como objetivo conhecer a composição desses produtos, a partir das informações nutricionais contidas nos sites das empresas produtoras, bem como as suas peculiaridades e concepções. Apesar da conotação natural e gastronômica, alto valor calórico, gorduras (especialmente na versão recheada sabor brigadeiro e elevadas quantidades de açúcares, foram encontrados, em média, por unidade: 207,2 Kcal; 38,4g de carboidratos; 3,9g de proteínas e 5,3g de gorduras. Uma rica ênfase na cultura mexicana, religiosidade e identidade visual marcante foram identificadas nos sites dos produtos pesquisados.

  12. COMO ANDAR SEM POESIA?

    Directory of Open Access Journals (Sweden)

    Angela Fronckowiak

    2008-11-01

    Full Text Available O artigo reflete sobre a fruição do gênero poético por crianças ainda não alfabetizadas a partir de momentos compartilhados com elas no cotidiano de escolas de Educação Infantil. Essa vivência, vinculada ao projeto de pesquisa Poesia e infância1, demonstrou a relevância de possibilitar às crianças um contato intenso com a poesia, texto singular que as capacita a expressar, na sua linguagem, o modo como interagem com o outro e com o mundo. Através de encontros semanais com crianças de 4 a 6 anos de duas escolas da região do Vale do Rio Pardo/RS, foi possível perceber uma extrema abertura da infância para os jogos vocabulares e sonoros. Na continuidade da pesquisa, pudemos estudar as características textuais mais valorizados pelas crianças na escuta de textos poéticos. Uma hipótese era a de que a audição regular de poemas potencializava a repercussão e a ressonância, aspectos apontados por Gaston Bachelard como intrínsecos ao devaneio poético, experiência oportunizada pela leitura/audição da poesia e que faculta ao leitor encontrar “um não-eu meu que me permite viver minha confiança de estar no mundo” (BACHELARD, 1988, p. 132. Ancorado nos resultados obtidos, este texto defende a rima e o discurso predominante do poema como fatores essenciais para os pequenos experimentarem a ressonância poética.

  13. Terroristas como actores internacionales

    OpenAIRE

    Caballero López, José Luis

    2016-01-01

    Este trabajo se fundamenta en la investigación sobre el "terrorismo y los terroristas como agentes internacionales" en un contexto amplio aunque principalmente focalizado en la actualidad. Los tiempos en los que nos encontramos hoy en día requieren estudiar con exactitud los rasgos de la política internacional referentes al terror. Destaca sobremanera el concepto "yihadismo" y todo lo que le rodea, pues la dictadura de terror que se vive contemporáneamente en Oriente Próximo se encuentra r...

  14. El mundo como proyecto

    OpenAIRE

    Sbarra, Alberto; Morano, Horacio; Cueto Rúa, Verónica

    2015-01-01

    Un profesor decía a sus alumnos: “…ahora ustedes comenzarán a mirar el mundo con ojos de arquitecto”1, recreando una visión totalizadora e integradora que incluye el pensamiento proyectual. Instalados en un determinado campo disciplinar, se tiene una nueva noción de la realidad, probablemente una nueva manera de mirar el mundo. Imaginar el mundo como proyecto2, lo hemos convertido en un desafío para la asignatura Teoría, en la creencia que el mundo es un proyecto inacabado, en donde la Arq...

  15. La independencia como problema

    OpenAIRE

    Lara Martínez, Rafael

    2009-01-01

    Este artículo examin la producción intelectual de una organización cultural salvadoreña: el Ateneo, instituido en diciembre de 1912. Sin establecer distinciones de género, estudia la manera en que poesía, narrativa y ensayo visualizan la independencia centroamericana y su corolario, la vida republicana durante las primeras décadas independientes. Los miembros fundadores del Ateneo describen la independencia como acontecimiento gratuito, sin voluntad popular ni determinación política seria. An...

  16. Aptamer Sensors

    OpenAIRE

    Marrazza, Giovanna

    2017-01-01

    In the last years, great progress has been accomplished in the development of aptamer sensors with different transducers. In order to improve the sensitivity of these biosensors, several methodologies have been employed. In this Special Issue, the state of art and the future trends in the field of aptamer sensors have been explored.

  17. Aprendizaje como reconfiguracion de agencia

    National Research Council Canada - National Science Library

    Larreamendy Joerns, Jorge

    2011-01-01

    En este articulo se ofrece una perspectiva sobre el aprendizaje como cambio en la identidad, tomando como punto de referencia la teoria de la participacion periferica legitima (PPL) de Lave y Wenger (1991...

  18. Soldier sensor

    Science.gov (United States)

    Kossives, Dean P.

    2010-04-01

    A new sensor system, whose functionality is not reliant on mass spectrometric or ionization methods, is combined with a substrate technology which allows for separately optimized control circuits and standardized advanced sensors in a simple packaging methodology to foster an entirely new generation of modular optical sensors. These sensors will be based on biologic and chromic compounds. The compounds will utilize reversible reaction chemistry to enable self cleaning. The detector's operation is based on simple changes in absorbance, reflectance, color, or other optical properties. The time to saturation of the sensor will determine the relative concentration in the air. A detection scheme based on these properties will function in high background levels and also be able to pick up low level concentrations as well.

  19. Pathogen Sensors

    Directory of Open Access Journals (Sweden)

    Joseph Irudayaraj

    2009-10-01

    Full Text Available The development of sensors for detecting foodborne pathogens has been motivated by the need to produce safe foods and to provide better healthcare. However, in the more recent times, these needs have been expanded to encompass issues relating to biosecurity, detection of plant and soil pathogens, microbial communities, and the environment. The range of technologies that currently flood the sensor market encompass PCR and microarray-based methods, an assortment of optical sensors (including bioluminescence and fluorescence, in addition to biosensor-based approaches that include piezoelectric, potentiometric, amperometric, and conductometric sensors to name a few. More recently, nanosensors have come into limelight, as a more sensitive and portable alternative, with some commercial success. However, key issues affecting the sensor community is the lack of standardization of the testing protocols and portability, among other desirable elements, which include timeliness, cost-effectiveness, user-friendliness, sensitivity and specificity. [...

  20. O ensaio como narrativa

    Directory of Open Access Journals (Sweden)

    Pedro Duarte

    2016-02-01

    Full Text Available O artigo tenta demonstrar que todos os textos, mesmo aqueles cuja natureza é teórica, têm alguma forma de narrativa. Nem sempre são personagens que os ocupam, podem ser ideias, mas mesmo assim há um enredo conceitual que se passa. Modernamente, a forma dessa narrativa foi sobretudo o sistema, com a pretensão totalizadora presente, por exemplo, na filosofia de Hegel. Contemporaneamente, porém, a forma do ensaio – surgida ainda na era moderna – ganha destaque por sua forma descontínua de narrar. O objetivo do artigo é apontar que, se o ensaio é uma forma, como explicitaram Lukács, Benjamin e Adorno, ele é também uma forma de narrar – ainda que de narrar conceitualmente objetos da cultura.

  1. COMO? PALETAS MEXICANAS BRASILEIRAS?

    OpenAIRE

    Daniela Maria Alves Chaud; Edeli Simioni Abreu; Andrea Carvalheiro Guerra Matias; Ana Carolina Oliveira

    2016-01-01

    As informações sobre alimentação estão mais acessíveis e democráticas. As tendências alimentares são inspiradas por diversos fatores, mas sempre estão associados à moda, mídia e como forma de conjectura de um estilo de vida. Há pouco tempo, as grandes cidades brasileiras foram invadidas por uma nova mania: as paletas mexicanas, que, na verdade, não são “tão mexicanas”. Esses sorvetes apresentam qualidades organolépticas marcantes, em virtude, entre outros fatores, ao alto teor de açúcar e, em...

  2. La identidad como performatividad

    Directory of Open Access Journals (Sweden)

    Andrés Felipe Castelar

    2008-12-01

    Full Text Available La presión social por constituir una forma indentitaria que sea acorde con el referente biológico es de origen histórico y se encuentra al servicio de prácticas de control y dominación social. Este artículo presenta una discusión sobre el lugar actual de la idea de identidad, especialmente en el plano de la sexualidad. Para esto recurre a la tesis de la filósofa Judith Butler, quien propone desde una visión deconstructivista y post-estructuralista una nueva definición de idenridad en términos de la iteración performativa. La identiclad es entendida entonces como una exigencia de inteligibiliclacl ante la sociedad, la cual limita las posibiliclades de expresión sexual.

  3. Como comunicar la Alegria

    Directory of Open Access Journals (Sweden)

    Pablo Portales

    2015-01-01

    Full Text Available Se ofrece un amplio análisis sobre la industria electoral, recordando que un candidato a presidente es "un producto para la venta". Se Desmenuzan las estrategias utilizadas en el plebiscito chileno,las elecciones norteamericanas con el NO a BUSH. El Mercadeo Social es una nueva metodología utilizada en proyectos de desarrollo a nivel de campo por ello se hace un esclarecimiento y clarifica el vínculo con la comunicación. Se agrega temas como: Los modelos de recepción de mensajes cuyos marcos conceptuales y metodologías aún no se han adaptado al potencial de esta línea de trabajo.Se analiza la agonía de las radios mineras en Bolivia en la que 42 años de historia y heroísmo se desmoronan.

  4. El inquisidor como profesor

    Directory of Open Access Journals (Sweden)

    Adriano PROSPERI

    2009-12-01

    Full Text Available Giovanni Botero, en una célebre página de su Ragion di stato, se detuvo sobre el tema de la fuerza de la religión en los gobiernos. Esta función de la religión cristiana —para Botero, católica— es garante del orden público y se presenta también como opuesta a la generadora de desorden de Lutero y Calvino, quienes siembran por todo cizañas y revoluciones de estados y ruinas de los reinos. Estamos en los orígenes del esquema historiografía de la periodización de la Edad Moderna que confió precisamente a la Reforma el papel de nodriza de las revoluciones que nacieron en Europa.

  5. La Justicia como virtud

    Directory of Open Access Journals (Sweden)

    Martínez-Sicluna y Sepúlveda, Consuelo

    2003-07-01

    Full Text Available El sentimiento de la justicia representa el hábito de conducta por el que nos vemos obligados, en cualquier relación, a dar a cada uno lo suyo. Ahora bien, esta disposición del espíritu se inscribe en las coordenadas que definen al hombre: verdad, libertad y bien. El hombre como ser racional y por tanto libre: el único ser que se determina a sí mismo y que alcanza en el bien el sentido de su proyección personal, esto es, la perfección. Dar a cada uno lo suyo es dar al sujeto el reconocimiento de este fundamento ontológico.

  6. Piezoceramic Sensors

    CERN Document Server

    Sharapov, Valeriy

    2011-01-01

    This book presents the latest and complete information about various types of piezosensors. A sensor is a converter of the measured physical size to an electric signal. Piezoelectric transducers and sensors are based on piezoelectric effects. They have proven to be versatile tools for the measurement of various processes. They are used for quality assurance, process control and for research and development in many different industries. In each area of application specific requirements to the parameters of transducers and sensors are developed. This book presents the fundamentals, technical des

  7. La persona como creatura

    Directory of Open Access Journals (Sweden)

    Emmanuel Housset

    2010-01-01

    Full Text Available El artículo de Emmanuel Housset implica un esfuerzo de rehabilitación del concepto «persona» para la filosofía contemporánea y la fenomenología. Para ello el autor busca mostrar cómo poco a poco «persona» tomó otra significación que la de «personaje» o sujeto de derecho. Es en autores como san Agustín y santo Tomás de Aquino que se halla un acceso diferente que pone el énfasis más bien en su carácter relacional y responsivo de la persona, antes que en su dimensión autónoma y autotélica. Tal dimensión aparece, según Housset, junto con la idea de persona como creatura y en oposición a la de individuo racional dueño de sí. La dimensión afectiva, la personalidad despertada por las diversas figuras de la alteridad son algunas de las dimensiones de la persona que examina el autor a partir del examen de la carne, las pasiones, la memoria, la historicidad y el amor alteridad.Emmanuel Housset's paper is an effort to revitalize the concept of 'person' for contemporary philosophy and phenomenology To this end the author looks to show how little by little the understanding of 'person' took on a different meaning to that of 'character' or "right bearing individual". It is in authors such as St. Augustine and St. Thomas Aquinas that a different approach is found, one that puts emphasis on the relational and responsive character of a person, rather than on the autonomous and auto telic dimension. According to Housset, such a dimension appears together with the idea of the person as a creation, and in opposition to the idea of the rational individual, that is his own master. The emotional dimension and the personality that is awoken by the many figures of alterity are some of the dimensions of the person that the author analyzes, based on examining the flesh, passions, memory historicity and love.

  8. El signo como emblema

    Directory of Open Access Journals (Sweden)

    Sáez, Carlos

    2003-06-01

    Full Text Available The aim of this article is to study the signs and symbols that appear in the hispanic medieval documents and manuscripts. These signs and symbols have usually been considered simply as mere elements to validate the charters. However, these alements were useful as a mean of visual communication between the high classes, able to generate charters, and the rest of medieval society—the majority illiterate— who received those charters. Because of their inability of understand an alphabetical code, they needed the graphic help to comprehend the message. Besides this, the article deals with non diplomatic signs and their function.

    Este artículo se centra en los signos o símbolos presentes en los documentos y manuscritos medievales hispanos, que habitualmente han sido tratados como meros elementos de validación de los diplomas. Pero estos elementos servían también de nexos de comunicación visual entre las clases poderosas, capaces de producir escritos, y los demás miembros de la sociedad medieval, receptores y destinatarios de tales escritos, en su mayoría analfabetos. Precisamente por esta razón, su incapacidad de descifrar un código alfabético, necesitan de auxilio gráfico para acercarse a la comprensión del mensaje. Asimismo, tratamos de los signos no diplomáticos y de su función.

  9. El riesgo como oportunidad

    Directory of Open Access Journals (Sweden)

    Daniela Gargantini

    2003-01-01

    Full Text Available Durante los últimos años el crecimiento mundial de catástrofes naturales ha ido en franco aumento. Sin embargo, desde un enfoque sistémico puede verificarse que la gran mayoría de los desastres se origina en los países en desarrollo (entre ellos los latinoamericanos, siendo las pérdidas en ellos significativamente más altas que en los países industrializados. Bajo esta postura los desastres no son sólo naturales sino socio- naturales, enfatizando la estrecha relación de causalidad entre modelos de desarrollo y urbanización y procesos de generación de riesgos, al incrementar la vulnerabilidad de los sectores más desprotegidos. El desastre pone en evidencia así una situación (la pobreza y segregación urbana ya existente, pero no considerada hasta el momento de la catástrofe. Frente a este panorama el desastre aparece como oportunidad que precipita tres catalizadores de políticas habitacionales: tierra, asistencia técnica y financiamiento, incrementando la celeridad y la creatividad de las respuestas. El interrogante que surge es por qué esperar el desastre para ponerlos en marcha, cuando ninguno de ellos es estrictamente dependiente de la situación de riesgo, sino sujeto de luchas de poder.

  10. Arte como espelho

    Directory of Open Access Journals (Sweden)

    Pedro Süssekind

    2016-12-01

    Full Text Available Este artigo tem como ponto de partida o exemplo da relação espelhada entre um livro e uma pintura de mesmo nome: o retrato que Lucian Freud fez do crítico de arte Martin Gayford e o diário que esse crítico escreveu sobre seu retratista, ambas as obras chamadas Homem com cachecol azul. A partir do exemplo, discuto a metáfora do espelho para caracterizar a arte, recorrendo para isso à teoria da representação artísticas elaborada pelo filósofo norte-americano Arthur Danto no artigo “O mundo da arte”, de 1964, e no primeiro capítulo do livro A transfiguração do lugar-comum, de 1981. Recorro, por fim, a dois exemplos artísticos de espelhamento na representação analisados por Danto em O abuso da beleza, de 2003, um quadro holandês do século dezessete e um poema de Rainer Maria Rilke.

  11. O analista como testemunha

    Directory of Open Access Journals (Sweden)

    Jô Gondar

    2016-04-01

    Full Text Available Resumo A proposta deste artigo é pensar o lugar da testemunha como um lugar terceiro que o analista, na clínica do traumático, é capaz de sustentar. Nos sonhos traumáticos, segundo Ferenczi, já existe a convocação de um terceiro. Não se trata da testemunha da esfera do Direito, tampouco do lugar do pai ou da Lei simbólica. Trata-se de um terceiro espaço que pode ser chamado de potencial, espaço intersticial, indeterminado e informe no qual circula - e aos poucos ganha forma -, algo que a princípio seria incomunicável. Esse espaço permite e suporta a literalidade da narrativa testemunhal, seus titubeios, paradoxos e silêncios. Mais do que uma teoria do trauma, a noção de espaço potencial seria a grande contribuição da psicanálise às pesquisas teóricas e clínicas com sobreviventes de campos de extermínio, de situações de tortura e de violência.

  12. Vibrissa Sensor

    Science.gov (United States)

    2016-09-30

    Docket No. 300119 1 of 11 VIBRISSA SENSOR STATEMENT OF GOVERNMENT INTEREST [0001] The invention described herein may be manufactured and used by...REFERENCE TO OTHER PATENT APPLICATIONS [0002] None. BACKGROUND OF THE INVENTION (1) Field of the Invention [0003] The present invention provides a...vibrissa in two dimensions. SUMMARY OF THE INVENTION [0010] Accordingly, it is an object of the present invention to provide a sensor capable of

  13. Ouabaina como Hormona

    Directory of Open Access Journals (Sweden)

    J. Hernando Ordoñez

    1996-04-01

    Full Text Available

    Comentario sobre su origen endógeno y sus aplicaciones terapéuticas

    Pocas drogas han sido más estudiadas que el grupo de los digitálicos, estrofantinas y ouabaina, cuyo estudio es objeto del presente trabajo.

    La ouabaina empezó a ser estudiada desde el siglo pasado. La primera referencia conocida corresponde a Pelikan, 1865 (1, como veneno que empleaban para las flechas en Gabón (Africa. (.

    (. Vinieron luego los trabajos de Fraser, 1869, (2, 3, 6, Polaillon, 1871 (4, Amaud, 1888 (5, Vaquez y Lutembacher, 1917 (7, Stoll, 1939 (8, Lapicque, 1929 (9, Wiggers, 1927 (10, Ytantos otros (11, 12, 13. En la obra de Kisch (14 aparecen más de 700 referencias bibliográficas sobre el particular.

    Ouabaina de origen endógeno. Purificación
    Durante muchos años se conoció la ouabaina como de origen vegetal, elaborada por las plantas Strophanthus Glaber(k-estrofantina,AcocantheraOuabaio(Ouabaina yStrophanthus Kombe (k-estrofantina y kestrofantósido. Una propiedad común a todos los digitálicos, estrofantina y ouabaina es que todos son inhibidores de la bomba de Na-K, encargada de regular la salida de Na y la entrada de K celular.

    Estudiando los inhibido res de esta bomba han encontrado en años recientes resultados extraordinarios en relación con el origen endógeno de algunos de estos inhibidores, entre ellos la ouabaina. Por considerarlos de extrema importancia y actualidad científica me permito citar algunos de ellos. Hamlyn y Manunta (15, 16, 17, 18, Y 19 hicieron estudios sobre el particular y lograron identificar en el plasma humano un compuesto igual a la ouabaina. Estos hallazgos fueron confirmados después por otros autores (20, 21, 22, 23 Y24.

    Ham bl yn (19 da varios argumentos que ponen en evidencia que el compuesto químico encontrado es ouabaina pura, y, lo que es más interesante, que tiene un origen endógeno. a Por espectroscopia de alta resoluci

  14. O direito como imperativo

    Directory of Open Access Journals (Sweden)

    Cloter Miglioriani

    1988-08-01

    Full Text Available We have examined one of the facets which Law presents to society, looking at the theme through a brief history of Law, in which Roman Law stands out, up to modem times, comparing current juridical systems such as the Continental System, Common Law, and Soviet Law. We have looked at Law from the viewpoint of society 's need to have basic mies for living together, with the juridical ruZe being one of the most important. We have highlighted the views of Hart and Kelsen on the foundations of the validity of Law. We have also considered the obligatoriness of Law; giving the point of view of tadbruch who, explaining his ''Theory of the Obligatoriness of Law ", concluded that the obligatoriness of Law can only be withdraw when there is a Clash between morals, law, use and social conventions. We have looked at the notion of the imperativeness of Law the central theme of the work -drawing on the views of Miguel Reale, for whom the juridical nonn cannot be reduced to a "command of a volitional nature", but rather the obligatory character of the juridical nonn arises from the pressure of social values. Del Vecchio, who is also quoted, recognized that imperativeness exists in the juridical norm, whether it is preceptive (a positive command or permissive. Also mentioned is the opinion of Tercio Sampaio Ferraz, for whom the juridical norm has imperativeness to the extent that the imposition of behaviour is unconditionally guaranteed. Foi feita a abordagem de uma das facetas com que o Direito se apresenta à sociedade, enfocando o tema a partir de um brevíssimo histórico do Direito, onde revela a fase romana, até os períodos modernos, com comparações dos sistemas jurídicos hodiernos, como o sistema continental, o da Commum Law e o soviético. Foi enfocado o Direito em face da necessidade sociedade em ter básicas de convivência, despontando a regra jurídica como das mais importantes. Foi dado destaque às posições de Hart e Kelsen, sobre os

  15. Acerca del sociologo como escritor

    National Research Council Canada - National Science Library

    Zurita, Carlos Virgilio

    2009-01-01

    ... empiricos y de metaforas verosimiles para ilustrar la vida social. Se mencionan diversos casos de utilizacion de materiales narrativos en el analisis sociologico, tanto tradicional como contemporaneo...

  16. Cobalt-rich alloys electrodeposited on silicon; Filmes de ligas ricas em cobalto eletrodepositado sobre silicio

    Energy Technology Data Exchange (ETDEWEB)

    Spada, E.R.; Dotto, M.E.R.; Sartorelli, M.L. [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Departamento de Fisica. Lab. de Sistemas Nanoestruturados; Paula, F.R. de, E-mail: depaula@dfq.feis.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Ilha Solteira, SP (Brazil). Departamento de Fisica e Quimica

    2014-07-01

    We report the electrodeposition (ED) of cobalt-rich alloy films on n-type Si (100) substrates in aqueous solution. A small amount of copper sulphate in the bath improved the quality of cobalt-rich films. The bath proved to be appropriate for the production of electrodeposited magnetic antidote structures prepared by nanosphere lithography technique. X-ray measurements indicate a mixture of hcp and fcc CoCu structures and strong texture in the (001) hcp and (111) fcc direction. Magnetic behavior was shown to be dependent on the thickness, which directly affects the domain wall pinning and the presence of superparamagnetism. (author)

  17. Optical fibre microwire sensors

    OpenAIRE

    Brambilla, G.; Belal, Mohammad; Jung, Y.; Song, Z.; Xu, F.; Newson, T.P.; Richardson, D.J.

    2011-01-01

    This paper reviews sensing applications of optical fibre microwires and nanowires. In addition to the usual benefits of sensors based on optical fibres, these sensors are extremely compact and have fast response speeds. In this review sensors will be grouped in three categories according to their morphology: linear sensors, resonant sensors and tip sensors. While linear and resonant sensors mainly exploit the fraction of power propagating outside the microwire physical boundary, tip sensors t...

  18. Corrosion sensor

    Science.gov (United States)

    Glass, Robert S.; Clarke, Jr., Willis L.; Ciarlo, Dino R.

    1994-01-01

    A corrosion sensor array incorporating individual elements for measuring various elements and ions, such as chloride, sulfide, copper, hydrogen (pH), etc. and elements for evaluating the instantaneous corrosion properties of structural materials. The exact combination and number of elements measured or monitored would depend upon the environmental conditions and materials used which are subject to corrosive effects. Such a corrosion monitoring system embedded in or mounted on a structure exposed to the environment would serve as an early warning system for the onset of severe corrosion problems for the structure, thus providing a safety factor as well as economic factors. The sensor array is accessed to an electronics/computational system, which provides a means for data collection and analysis.

  19. Pressure sensor

    Science.gov (United States)

    Mee, David K.; Ripley, Edward B.; Nienstedt, Zachary C.; Nienstedt, Alex W.; Howell, Jr., Layton N.

    2015-09-29

    Disclosed is a passive, in-situ pressure sensor. The sensor includes a sensing element having a ferromagnetic metal and a tension inducing mechanism coupled to the ferromagnetic metal. The tension inducing mechanism is operable to change a tensile stress upon the ferromagnetic metal based on a change in pressure in the sensing element. Changes in pressure are detected based on changes in the magnetic switching characteristics of the ferromagnetic metal when subjected to an alternating magnetic field caused by the change in the tensile stress. The sensing element is embeddable in a closed system for detecting pressure changes without the need for any penetrations of the system for power or data acquisition by detecting changes in the magnetic switching characteristics of the ferromagnetic metal caused by the tensile stress.

  20. Hydrogen sensor

    Science.gov (United States)

    Duan, Yixiang; Jia, Quanxi; Cao, Wenqing

    2010-11-23

    A hydrogen sensor for detecting/quantitating hydrogen and hydrogen isotopes includes a sampling line and a microplasma generator that excites hydrogen from a gas sample and produces light emission from excited hydrogen. A power supply provides power to the microplasma generator, and a spectrometer generates an emission spectrum from the light emission. A programmable computer is adapted for determining whether or not the gas sample includes hydrogen, and for quantitating the amount of hydrogen and/or hydrogen isotopes are present in the gas sample.

  1. El paisaje como estrategia proyectual

    OpenAIRE

    Mínguez Martínez, Enrique

    2014-01-01

    La presente comunicación tiene por objeto presentar los trabajos realizados por los alumnos de la asignatura de Urbanística III de la titulación Grado en Arquitectura de la Universidad Católica San Antonio de Murcia (UCAM). Mientras que en el Urbanismo funcionalista el objeto del proyecto son los edificios y el paisaje se entiende como un relleno verde, residual, identificado por Colin Rowe en Ciudad Collage (1978) como modelo Acrópolis, en los ejercicios realizados el análisis pormenorizado ...

  2. Montagem e Imagem como Paradigma

    Directory of Open Access Journals (Sweden)

    Cesar Huapaya

    2016-01-01

    Full Text Available O pensar como montagem e imagem tornou-se um método revelador nos processos de estudos práticos e teóricos do artista e dos pesquisadores nos séculos XX e XXI. Este artigo procura articular três formas de pensar por montagem: nas obras de Bertolt Brecht, Sergei Eisenstein e Georges DidiHuberman. O filósofo e historiador da arte Georges Didi-Huberman reinaugura o debate e o exercício de pensar a antropologia da imagem e a montagem como metalinguagem e forma de conhecimento.

  3. El cuadro como espejo luminoso

    OpenAIRE

    Gonzalo Carbó, Antoni

    2003-01-01

    En 'Algunos lugares de la pintura' María Zambrano, comentando el conocido cuadro de La tempestad de Giorgione, escribe: «Como si el cuadro estuviese visto a través de un cristal y no se le pudiera tocar [ ]». Nuestra autora parece hacer referencia aquí a una imagen de origen platónico que sin duda es recurrente en su obra: la transparencia del alma o del corazón, pues la «transcendencia es transparencia». María Zambrano concibe el plano del cuadro como una superficie vítrea, pulimentada, tran...

  4. La ciudad como ecosistema urbano

    OpenAIRE

    Higueras García, Esther

    2013-01-01

    LA CIUDAD COMO ECOSISTEMA URBANO .- La ecología y los ecosistemas .- El ecosistema urbano, definición, alcance y oportunidad .- El metabolismo urbano .- Los síntomas de la patología urbana .- Los objetivos del nuevo ecosistema urbano .- Las aportaciones de los ecobarrios

  5. Sensors for Entertainment.

    Science.gov (United States)

    Lamberti, Fabrizio; Sanna, Andrea; Rokne, Jon

    2016-07-15

    Sensors are becoming ubiquitous in all areas of science, technology, and society. In this Special Issue on "Sensors for Entertainment", developments in progress and the current state of application scenarios for sensors in the field of entertainment is explored.

  6. Wireless sensor platform

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, Pooran C.; Killough, Stephen M.; Kuruganti, Phani Teja

    2017-08-08

    A wireless sensor platform and methods of manufacture are provided. The platform involves providing a plurality of wireless sensors, where each of the sensors is fabricated on flexible substrates using printing techniques and low temperature curing. Each of the sensors can include planar sensor elements and planar antennas defined using the printing and curing. Further, each of the sensors can include a communications system configured to encode the data from the sensors into a spread spectrum code sequence that is transmitted to a central computer(s) for use in monitoring an area associated with the sensors.

  7. El singular como diferencia divina

    Directory of Open Access Journals (Sweden)

    Maria Jose Binetti

    2012-01-01

    Full Text Available Mucho se ha hablado sobre la posición de la diferencia como motor dialéctico de la existencia singular kierkegaardiana. El pecado, el otro o el Otro fisuran la subjetividad humana y la obligan a una identidad que guardará siempre la herida. El sujeto de la escisión es, en este sentido, el existente mismo, y tal debe ser el caso si la perspectiva se concentra en la individualidad. No obstante, y desde el punto de vista especulativo, creemos que los mismos principios utilizados por Kierkegaard para explicar el dinamismo de la existencia singular nos llevan más lejos, a saber, nos conducen al absoluto mismo como sujeto último de toda alteridad, respecto del cual el singular hace la diferencia.

  8. del museo como proyecto ilustrado

    Directory of Open Access Journals (Sweden)

    Adolfo Vásquez Rocca

    2008-01-01

    Full Text Available Se intenta aquí superar la tradicional antinomia entre arte y tecnología. En cambio, se propone una comprensión del arte posmoderno a partir de la inscripción del artista en el seno de una cultura de la información. Es así como asistimos a un cambio de paradigma en el estatuto del arte, a una revolución en la escena artística y de nuestros regímenes de visibilidad, de allí la necesidad de explorar el desarrollo de las estéticas de la virtualidad que nos instalan en nuevas lógicas de producción de verdad, emancipadas del museo como instancia última de legitimación artística.

  9. JORNALISMO COMO CAMPO DE PESQUISA

    Directory of Open Access Journals (Sweden)

    Muniz Sodré

    2011-02-01

    Full Text Available Trata-se de enfatizar como necessária a correlação da prática
    jornalística com a totalidade cultural em suas mutações por efeito
    das novas tecnologias da informação e da comunicação. Uma das
    preliminares epistemológicas é a crítica da concepção informacional, que concebe a comunicação como mera transferência de conteúdos de um polo a outro e que vem sustentando teoricamente a maior parte dos estudos de mídia. Midiatização, retórica e mercado. Narratividade e prática jornalística.

  10. Jornalismo como campo de pesquisa

    Directory of Open Access Journals (Sweden)

    Muniz Sodré

    2015-03-01

    Full Text Available Trata-se de enfatizar como necessária a correlação da prática jornalística com a totalidade cultural em suas mutações por efeito das novas tecnologias da informação e da comunicação. Uma das preliminares epistemológicas é a crítica da concepção informacional, que concebe a comunicação como mera transferência de conteúdos de um polo a outro e que vem sustentando teoricamente a maior parte dos estudos de mídia. Midiatização, retórica e mercado. Narratividade e prática jornalística.

  11. La identidad como problematica latinoamericana

    OpenAIRE

    Gómez de González, Blanca Inés; Profesora de Literatura en la Universidad Javeriana, Pedagógica Nacional y Sabana.

    2004-01-01

    La reflexión sobre el ser es un problema de la época moderna en América Latina y ha hilvanado la historia de América como un largo viaje hacia su propio encuentro. América se postula como el continente de la gran equivocación y el enfrentamiento del hombre a su realidad marca el derrotero de la creación americana. "El mundo recién descubierto no estaba localizado aún en el planeta ni tenía forma ninguna. Era una caprichosa ex­tensión de la tierra poblada de imágenes. Había nacido de un error ...

  12. Gas Sensors: A Review

    Directory of Open Access Journals (Sweden)

    Zainab Yunusa

    2014-04-01

    Full Text Available In this paper a review of different technologies for gas sensors is presented. The different types of gas sensors technologies including catalytic gas sensor, electrochemical gas sensors, thermal conductivity gas sensor, optical gas sensor and acoustic gas sensor are discussed together with their principle of operation. The Surface Acoustic Wave Gas Sensor technology is discussed in greater detail. The advantages and disadvantages of each sensor technology are also highlighted. All these technologies have been used for several decades for the development of highly sensitive and responsive gas sensors for the detection of flammable and hazardous gases. However, for improved sensitivity and selectivity for these sensors, future trends and outlook for researchers are suggested in the conclusion of this article.

  13. Jornalismo como campo de pesquisa

    Directory of Open Access Journals (Sweden)

    Muniz Sodré

    2010-12-01

    preliminares epistemológicas é a crítica da concepção informacional, que concebe a comunicação como mera transferência de conteúdos de um polo a outro e que vem sustentando teoricamente a maior parte dos estudos de mídia. Midiatização, retórica e mercado. Narratividade e prática jornalística.

  14. El movimiento como componente musical

    OpenAIRE

    Mesa, Paula; Gallo, Alejandro; Chlopecki, Oreste; Balderrabano, Sergio

    1999-01-01

    En las teorías contemporáneas de la música tonal, observamos que el concepto del movimiento sur-ge como consecuencia de la interacción entre el ritmo, el metro y las alturas. Desde este lugar, el movimiento musical es vinculado a cuestiones del orden de la notación, de lo mensurable, de lo cuantificable. Facultad de Bellas Artes

  15. Los ancianos como actores sociales

    Directory of Open Access Journals (Sweden)

    Mª PIA ARENYS

    1996-01-01

    Full Text Available En este artículo se recogen las discusiones de grupo que se realizaron durante cuatro meses en Barcelona como preparación del "II congreso de la gent gran" (II congreso de ancianos de esta ciudad, en noviembre de 1993. las discusiones se llevaron a cabo en las sedes de cada distrito, previa presentación de la ponencia por parte de un técnico. los componentes de los grupos son personas mayores sensibilizadas y comprometidas que forman parte del consejo de bienestar social del ayuntamiento de Barcelona. la metodología utilizada es cualitativa para el análisis del discurso, que se ha estructurado en los siguientes puntos: bajo el epígrafe "los ancianos como ciudadanos de derechos y obligaciones" se recogen los temas de valoración de la vejez, la familia, la jubilación, las implicaciones de los ancianos como ciudadanos de derechos y deberes y las funciones sociales de los ancianos.-- sobre estos temas, los mayores expresaron sus opiniones, que se vertieron, resumidamente, en la redacción final de la ponencia. aquí se recogen y se han analizado los materiales que ofrecen una versión de primera mano sobre lo que opinan los ancianos respecto al tema de "la valoración de la vejez".

  16. A literatura como antropologia especulativa

    Directory of Open Access Journals (Sweden)

    Alexandre Andre Nodari

    2015-11-01

    Full Text Available Se décadas atrás, Lyotard identificou a crise de legitimação política e do conhecimento de então como a crise dos grandes relatos, talvez se possa dizer que a crise atual é uma crise do grande Relator: a crise das humanidades seria, assim, parte mais geral da crise do Humano. Diante do Antropoceno, as ciências do homem (as antropologias têm como um dos seus desafios converterem-se em humanidades, isto é, especular sobre as definições de homem e mundo, descobrindo outras humanidades e mundos. Aqui, a literatura, entendida a partir de Juan José Saer como uma “antropologia especulativa”, pode revelar-se uma linha de fuga: diante do contingenciamento econômico das humanidades, ela apresenta a contingência ecológica desse modelo de mundo.     This work is licensed under a Creative Commons Attribution 3.0 License.

  17. A modular optical sensor

    Science.gov (United States)

    Conklin, John Albert

    This dissertation presents the design of a modular, fiber-optic sensor and the results obtained from testing the modular sensor. The modular fiber-optic sensor is constructed in such manner that the sensor diaphragm can be replaced with different configurations to detect numerous physical phenomena. Additionally, different fiber-optic detection systems can be attached to the sensor. Initially, the modular sensor was developed to be used by university of students to investigate realistic optical sensors and detection systems to prepare for advance studies of micro-optical mechanical systems (MOMS). The design accomplishes this by doing two things. First, the design significantly lowers the costs associated with studying optical sensors by modularizing the sensor design. Second, the sensor broadens the number of physical phenomena that students can apply optical sensing techniques to in a fiber optics sensor course. The dissertation is divided into seven chapters covering the historical development of fiber-optic sensors, a theoretical overview of fiber-optic sensors, the design, fabrication, and the testing of the modular sensor developed in the course of this work. Chapter 1 discusses, in detail, how this dissertation is organized and states the purpose of the dissertation. Chapter 2 presents an historical overview of the development of optical fibers, optical pressure sensors, and fibers, optical pressure sensors, and optical microphones. Chapter 3 reviews the theory of multi-fiber optic detection systems, optical microphones, and pressure sensors. Chapter 4 presents the design details of the modular, optical sensor. Chapter 5 delves into how the modular sensor is fabricated and how the detection systems are constructed. Chapter 6 presents the data collected from the microphone and pressure sensor configurations of the modular sensor. Finally, Chapter 7 discusses the data collected and draws conclusions about the design based on the data collected. Chapter 7 also

  18. EDITORIAL: Humidity sensors Humidity sensors

    Science.gov (United States)

    Regtien, Paul P. L.

    2012-01-01

    produced at relatively low cost. Therefore, they find wide use in lots of applications. However, the method requires a material that possesses some conflicting properties: stable and reproducible relations between air humidity, moisture uptake and a specific property (for instance the length of a hair, the electrical impedance of the material), fast absorption and desorption of the water vapour (to obtain a short response time), small hysteresis, wide range of relative humidity (RH) and temperature-independent output (only responsive to RH). For these reasons, much research is done and is still going on to find suitable materials that combine high performance and low price. In this special feature, three of the four papers report on absorption sensors, all with different focus. Aziz et al describe experiments with newly developed materials. The surface structure is extensively studied, in view of its ability to rapidly absorb water vapour and exhibit a reproducible change in the resistance and capacitance of the device. Sanchez et al employ optical fibres coated with a thin moisture-absorbing layer as a sensitive humidity sensor. They have studied various coating materials and investigated the possibility of using changes in optical properties of the fibre (here the lossy mode resonance) due to a change in humidity of the surrounding air. The third paper, by Weremczuk et al, focuses on a cheap fabrication method for absorption-based humidity sensors. The inkjet technology appears to be suitable for mass fabrication of such sensors, which is demonstrated by extensive measurements of the electrical properties (resistance and capacitance) of the absorbing layers. Moreover, they have developed a model that describes the relation between humidity and the electrical parameters of the moisture-sensitive layer. Despite intensive research, absorption sensors still do not meet the requirements for high accuracy applications. The dew-point temperature method is more appropriate

  19. Sensors in Smart Phone

    OpenAIRE

    Pei, Chunmei; Guo, Huiling; Yang, Xiuqing; Wang, Yangqiu; Zhang, Xiaojing; Ye, Hairong

    2010-01-01

    International audience; The technological innovation in electronics makes nowadays mobile phone more than a simple communication tool: it becomes a portable electronic device with integrated functions, such as listening to music, watching movies, taking photos, etc. To achieve these, many kinds of advanced sensor are used. In this paper, several applications of sensor in smart phone are introduced including Image Sensor, Fingerprint Identification Sensor, Photo-electric Sensor, Acceleration S...

  20. Internet como nuevo modelo educativo

    OpenAIRE

    Collazos, Cesar A.

    2000-01-01

    Se ha vuelto ineludible analizar las relaciones existentes entre las tecnologías informáticas y el campo educativo, con el objetivo de aprovechar el potencial de las primeras dentro del proceso de enseñanza-aprendizaje. Día a día se cuenta con mayores y mejores herramientas computacionales, que se colocan al servicio del hombre con el objetivo de facilitar sus actividades diarias tanto en el ámbito laboral como en el personal. El rol de muchos profesores está cambiando, del modelo tradi...

  1. La solidaridad como principio constitucional

    OpenAIRE

    Fernández Segado, Francisco

    2012-01-01

    El art. 2º de la Constitución establece el principio de solidaridad como un principio general de organización del Estado. Sin embargo, a la vista de otros preceptos constitucionales, hay que decir que el principio presenta un contenido esencialmente económico. Con todo, limitar el contenido del principio constitucional de solidaridad a lo estrictamente económico, esto es, a una equidistribución de la riqueza entre todas las regiones, sería una interpretación errónea. En efecto, el principio d...

  2. Del cuerpo como sensibilidad colonizada

    OpenAIRE

    Chervero, Joaquín; D'Hers, Victoria

    2012-01-01

    Retornamos al concepto cuerpos hacia la caracterización de las políticas de los cuerpos del capitalismo dependiente. Sobrevolados por una imposibilidad de dar cuenta de lo que puede un cuerpo -cuerpo como inasible-, nos mueve el desafío de un objeto que al tiempo que nos configura íntimamente, se nos escapa. Así, reflexionamos sobre el cuerpo en su ser sensible, en tanto un modo de existencia implica una forma específica de regulación. ¿En qué consiste el devenir de lo sensible? ¿Cuáles son s...

  3. Las franquicias como estrategia emprendedora

    OpenAIRE

    Paz, Gustavo Darío

    2017-01-01

    177 p. il. El tema de la presente investigación “Las franquicias como estrategia emprendedora” se introduce en el contexto del sistema de franchising. El objetivo principal es conocer por qué los emprendedores se inclinan por comercializar con franquicias ubicadas en la Ciudad de Salta, durante el año 2017. Este trabajo está enmarcado dentro de un enfoque cualitativo, de carácter descriptivo. El diseño que sustenta el desarrollo del presente trabajo se basa en la utilización de la encue...

  4. El dictado como tarea comunicativa

    Directory of Open Access Journals (Sweden)

    Daniel Cassany

    2004-01-01

    Full Text Available El artículo explora las utilidades didácticas del dictado (la práctica comunicativa de oralizar o leer en voz alta un escrito para el aprendizaje funcional de una lengua materna o extranjera, en los diversos niveles de enseñanza. Después de criticar el uso tradicional de este ejercicio lingüístico, presentamos once formas diferentes de desarrollar un dictado en clase, con sus particulares contenidos, objetivos y metodologías. También analizamos con detalle la técnica más tradicional del dictado magistral, en la que el docente dicta palabra por palabra un texto al alumnado, poniendo énfasis en la ortografía; ofrecemos algunas orientaciones para incrementar el componente comunicativo de esta propuesta. Las conclusiones finales proponen entender esta técnica como un recurso metodológico variado, rico y sugerente, adaptado a cada situación de aprendizaje —y no como una práctica obligatoria y fosilizada.

  5. Towards Sensor Database Systems

    DEFF Research Database (Denmark)

    Bonnet, Philippe; Gehrke, Johannes; Seshadri, Praveen

    2001-01-01

    . These systems lack flexibility because data is extracted in a predefined way; also, they do not scale to a large number of devices because large volumes of raw data are transferred regardless of the queries that are submitted. In our new concept of sensor database system, queries dictate which data is extracted...... from the sensors. In this paper, we define the concept of sensor databases mixing stored data represented as relations and sensor data represented as time series. Each long-running query formulated over a sensor database defines a persistent view, which is maintained during a given time interval. We...... also describe the design and implementation of the COUGAR sensor database system....

  6. Como Lo Hago Yo: Myelomeningocele

    Science.gov (United States)

    Lazareff, Jorge

    2014-01-01

    Fortificación con ádico fólico es efectiva, pero aún falta conciencia en los jóvenes. La legalidad del aborto aumenta la importancia de la consulta prenatal. Realizo la cirugía bajo microcoscopio por razones didácticas. Irrigación continua para reducir la temperatura del tejido. Trato a la plaqueta como tejido viable. No suturo la plaqueta. No cierro músculo. ATB por una semana después de cirugía. Hidrocefalia: Válvula en todos los casos de ventriculomegalia. Médula anclada: Desanclar una sola vez. Chiari II: Revisar la válvula. Incluir en el seguimiento rendimiento escolar, puede indicar obstrucción de la válvula o médula anclada. PMID:24791217

  7. Vivencias afectivas como discurso virtual

    Directory of Open Access Journals (Sweden)

    Mijaíl Málishev

    2011-01-01

    Full Text Available El discurso virtual expresa nuestras vivencias afectivas tanto en el futuro -esperanza- como en el pasado -culpa y venganza-. La esperanza es un estímulo que nos alienta a alcanzar nuestras metas. A diferencia del futuro, el pasado es irreversible y, sin embargo, el pluscuamperfecto es un "mago" que "transforma" lo irreparable en lo virtual. Nuestra conciencia nos hace sentir culpables, haciéndonos creer que lo indebido que hemos cometido, hubiéramos podido hacerlo de otra manera. El pluscuamperfecto expresa la venganza que nos hace "lavar la ofensa" causada por nuestro adversario, pero el discurso virtual en el pluscuamperfecto nos ayuda a sublimar nuestros rencores sin causar algún daño a nuestro adversario y a nuestra propia reputación.

  8. administra como anticonceptivo de emergencia

    Directory of Open Access Journals (Sweden)

    Horacio Croxatto

    2007-01-01

    Full Text Available La anticoncepción hormonal de emergencia (AHE es uno de los pocos recursos que la mujer puede usar para prevenir un embarazo no deseado después de haber tenido una relación sexual en la que no usó método anticonceptivo o el que usó presentó una falla. Actualmente, el método preferido para la AHE es la píldora que contiene solamente levonorgestrel (LNG. Según la OMS, puede prevenir embarazos si se usa hasta 120 horas después del acto sexual, pero su eficacia disminuye drásticamente desde 85% a 31% mientras más se posterga su administración. La introducción de la AHE ha generado controversia en muchos países latinoamericanos por la percepción errónea de que induce aborto y la oposición de los sectores más conservadores de la sociedad que temen que favorezca la promiscuidad. Con el propósito de dar a conocer la evidencia científica producida por las investigaciones diseñadas para dilucidar como el LNG previene el embarazo cuando se administra como AHE, y su correcta interpretación, este artículo analiza críticamente dichos estudios y explica además en que circunstancias este método no logra prevenir el embarazo. El conjunto de la evidencia indica que LNG previene el embarazo solamente cuando impide la fecundación y descarta que el prevenga el embarazo interfiriendo con la implantación del embrión, por lo que la creencia de que es abortivo no tiene sustento científico.

  9. Embedded sensor systems

    CERN Document Server

    Agrawal, Dharma Prakash

    2017-01-01

    This inspiring textbook provides an introduction to wireless technologies for sensors, explores potential use of sensors for numerous applications, and utilizes probability theory and mathematical methods as a means of embedding sensors in system design. It discusses the need for synchronization and underlying limitations, inter-relation between given coverage and connectivity to number of sensors needed, and the use of geometrical distance to determine location of the base station for data collection and explore use of anchor nodes for relative position determination of sensors. The book explores energy conservation, communication using TCP, the need for clustering and data aggregation, and residual energy determination and energy harvesting. It covers key topics of sensor communication like mobile base stations and relay nodes, delay-tolerant sensor networks, and remote sensing and possible applications. The book defines routing methods and do performance evaluation for random and regular sensor topology an...

  10. Air Sensor Toolbox

    Science.gov (United States)

    Air Sensor Toolbox provides information to citizen scientists, researchers and developers interested in learning more about new lower-cost compact air sensor technologies and tools for measuring air quality.

  11. Biomedical Sensors of Ionizing Radiation

    OpenAIRE

    Pani, S; Speller, R; Royle, G; Olivo, A

    2010-01-01

    Sensors Technology Series Editor-in-Chief's Preface vii Preface ix 1 Biomedical Sensors: Temperature Sensor ... G. Kim Prisk 4 Biomedical Sensors of Ionizing Radiation 129 Robert Speller, Alessandro Olivo, Silvia Pani, and Gary Royle 5 ...

  12. Digital Sensor Technology

    Energy Technology Data Exchange (ETDEWEB)

    Ted Quinn; Jerry Mauck; Richard Bockhorst; Ken Thomas

    2013-07-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy, reliability, availability, and maintainability. This report demonstrates these benefits in direct comparisons of digital and analog sensor applications. It also addresses the qualification issues that must be addressed in the application of digital sensor technology.

  13. Acoustic Humidity Sensor

    Science.gov (United States)

    Shakkottai, Parthasarathy; Kwack, Eug Y.; Venkateshan, Shakkottai

    1990-01-01

    Industrial humidity sensor measures volume fraction of water in air via its effect on speed of sound. Only portion of sensor exposed to sensed atmosphere is pair of stainless-steel tubes, one containing dry air and other containing moist air. Counters measure intervals between reflected pulses. Sensor rugged enough for use in harsh environments like those used to control drying of paper in paper mills, where most humidity sensors do not survive.

  14. Laser sensor system documentation.

    Science.gov (United States)

    2017-03-01

    Phase 1 of TxDOT Project 0-6873, True Road Surface Deflection Measuring Device, developed a : laser sensor system based on several sensors mounted on a rigid beam. : This sensor system remains with CTR currently, as the project is moving into Phase 2...

  15. Sensors for Entertainment

    Directory of Open Access Journals (Sweden)

    Fabrizio Lamberti

    2016-07-01

    Full Text Available Sensors are becoming ubiquitous in all areas of science, technology, and society. In this Special Issue on “Sensors for Entertainment”, developments in progress and the current state of application scenarios for sensors in the field of entertainment is explored.

  16. Sensors and actuators, Twente

    NARCIS (Netherlands)

    Bergveld, Piet

    1989-01-01

    This paper describes the organization and the research programme of the Sensor and Actuator (S&A) Research Unit of the University of Twente, Enschede, the Netherlands. It includes short descriptions of all present projects concerning: micromachined mechanical sensors and actuators, optical sensors,

  17. Thermal flow micro sensors

    NARCIS (Netherlands)

    Elwenspoek, Michael Curt

    1999-01-01

    A review is given on sensors fabricated by silicon micromachining technology using the thermal domain for the measurement of fluid flow. Attention is paid especially to performance and geometry of the sensors. Three basic types of thermal flow sensors are discussed: anemometers, calorimetric flow

  18. Automotive vehicle sensors

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S.H.; Raptis, A.C.; Moscynski, M.J.

    1995-09-01

    This report is an introduction to the field of automotive vehicle sensors. It contains a prototype data base for companies working in automotive vehicle sensors, as well as a prototype data base for automotive vehicle sensors. A market analysis is also included.

  19. Extra Sensor Perception

    Directory of Open Access Journals (Sweden)

    Javad MOKHBERY

    2007-01-01

    Full Text Available This article describes the importance of sensor verification. It also describes the benefits of a portable sensor verification system and how it can be an essential tool that compliments any program in which sensors are used for control manufacturing or during critical testing.

  20. Um estudo da adaptabilidade dos sistemas eletrônicos de controle de malha fechada pelo sensor de oxigênio de motores ciclo Otto à gasolina ao receber álcool etílico hidratado como combustível alternativo

    OpenAIRE

    Armando José Dal Bem

    2003-01-01

    Traz um histórico da utilização do álcool como combustível no Brasil, mostrando suas vantagens ambientais, sociais e econômicas. Apresenta as propriedades físico-químicas do álcool etílico anidro e hidratado e suas reações de combustão, enfatizando a razão ar/combustível e comparando-o com a gasolina pura e a gasolina comercial brasileira. Utiliza as teorias existentes sobre motores de combustão interna quatro tempos, para demonstrar a influência da adição progressiva de álcool etílico hidrat...

  1. Virtual Sensor Test Instrumentation

    Science.gov (United States)

    Wang, Roy

    2011-01-01

    Virtual Sensor Test Instrumentation is based on the concept of smart sensor technology for testing with intelligence needed to perform sell-diagnosis of health, and to participate in a hierarchy of health determination at sensor, process, and system levels. A virtual sensor test instrumentation consists of five elements: (1) a common sensor interface, (2) microprocessor, (3) wireless interface, (4) signal conditioning and ADC/DAC (analog-to-digital conversion/ digital-to-analog conversion), and (5) onboard EEPROM (electrically erasable programmable read-only memory) for metadata storage and executable software to create powerful, scalable, reconfigurable, and reliable embedded and distributed test instruments. In order to maximize the efficient data conversion through the smart sensor node, plug-and-play functionality is required to interface with traditional sensors to enhance their identity and capabilities for data processing and communications. Virtual sensor test instrumentation can be accessible wirelessly via a Network Capable Application Processor (NCAP) or a Smart Transducer Interlace Module (STIM) that may be managed under real-time rule engines for mission-critical applications. The transducer senses the physical quantity being measured and converts it into an electrical signal. The signal is fed to an A/D converter, and is ready for use by the processor to execute functional transformation based on the sensor characteristics stored in a Transducer Electronic Data Sheet (TEDS). Virtual sensor test instrumentation is built upon an open-system architecture with standardized protocol modules/stacks to interface with industry standards and commonly used software. One major benefit for deploying the virtual sensor test instrumentation is the ability, through a plug-and-play common interface, to convert raw sensor data in either analog or digital form, to an IEEE 1451 standard-based smart sensor, which has instructions to program sensors for a wide variety of

  2. Multifuctional integrated sensors (MFISES).

    Energy Technology Data Exchange (ETDEWEB)

    Homeijer, Brian D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Roozeboom, Clifton [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-10-01

    Many emerging IoT applications require sensing of multiple physical and environmental parameters for: completeness of information, measurement validation, unexpected demands, improved performance. For example, a typical outdoor weather station measures temperature, humidity, barometric pressure, light intensity, rainfall, wind speed and direction. Existing sensor technologies do not directly address the demand for cost, size, and power reduction in multi-paramater sensing applications. Industry sensor manufacturers have developed integrated sensor systems for inertial measurements that combine accelerometers, gyroscopes, and magnetometers, but do not address environmental sensing functionality. In existing research literature, a technology gap exists between the functionality of MEMS sensors and the real world applications of the sensors systems.

  3. ITA Sensor Fabric

    Science.gov (United States)

    Wright, Joel; Gibson, Christopher; Bergamaschi, Flavio; Marcus, Kelvin; Pham, Tien; Pressley, Ryan; Verma, Gunjan

    2009-05-01

    The diverse sensor types and networking technologies commonly used in fielded sensro networks provide a unique set of challenges [1] in the areas of sensor identification, interoperability, and sensor data consumability. The ITA Senor Fabric is a middleware infrastructure - developed as part of the International Technology Alliance (ITA)[2] in Network and Information Science - that addresses these challenges by providing unified access to, and management of, sensor networks. The Fabric spans the network from command and control, through forward operating bases, and out to mobile forces and fielded sensors, maximizing the availability and utility of intelligence information to users.

  4. Sensor mount assemblies and sensor assemblies

    Science.gov (United States)

    Miller, David H [Redondo Beach, CA

    2012-04-10

    Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

  5. Wireless Biological Electronic Sensors.

    Science.gov (United States)

    Cui, Yue

    2017-10-09

    The development of wireless biological electronic sensors could open up significant advances for both fundamental studies and practical applications in a variety of areas, including medical diagnosis, environmental monitoring, and defense applications. One of the major challenges in the development of wireless bioelectronic sensors is the successful integration of biosensing units and wireless signal transducers. In recent years, there are a few types of wireless communication systems that have been integrated with biosensing systems to construct wireless bioelectronic sensors. To successfully construct wireless biological electronic sensors, there are several interesting questions: What types of biosensing transducers can be used in wireless bioelectronic sensors? What types of wireless systems can be integrated with biosensing transducers to construct wireless bioelectronic sensors? How are the electrical sensing signals generated and transmitted? This review will highlight the early attempts to address these questions in the development of wireless biological electronic sensors.

  6. Sensor technology foresight

    DEFF Research Database (Denmark)

    Andersen, Per Dannemand; Jørgensen, Birte Holst; Rasmussen, Birgitte

    2001-01-01

    , robustness, dispensability, and the abilityto be self-calibrating. Future sensors are expected to be integrated systems with multiple applications. The market sectors most influenced by new sensor technology change from topic to topic. But a general conclusion is that health care is the marketsector most......The Sensor Technology Center A/S (STC) in co-operation with Risoe National Laboratory has carried out a sensor technology foresight in order to strengthen a strategic outlook on sensor technology. The technology foresight (with a timeframe of 2000 to2015) has been performed in the period October...... 2000 - September 2001. The conclusions of the sensor technology report are based on 1) a scanning of existing forward looking literature on sensor technology, 2) a number of workshops with Danish andinternational participants and 3) an international survey with 174 respondents. Half of the respondents...

  7. Silicon force sensor

    Energy Technology Data Exchange (ETDEWEB)

    Galambos, Paul C.; Crenshaw, Thomas B.; Nishida, Erik E.; Burnett, Damon J.; Lantz, Jeffrey W.

    2016-07-05

    The various technologies presented herein relate to a sensor for measurement of high forces and/or high load shock rate(s), whereby the sensor utilizes silicon as the sensing element. A plate of Si can have a thinned region formed therein on which can be formed a number of traces operating as a Wheatstone bridge. The brittle Si can be incorporated into a layered structure comprising ductile and/or compliant materials. The sensor can have a washer-like configuration which can be incorporated into a nut and bolt configuration, whereby tightening of the nut and bolt can facilitate application of a compressive preload upon the sensor. Upon application of an impact load on the bolt, the compressive load on the sensor can be reduced (e.g., moves towards zero-load), however the magnitude of the preload can be such that the load on the sensor does not translate to tensile stress being applied to the sensor.

  8. MEMS optical sensor

    DEFF Research Database (Denmark)

    2013-01-01

    The present invention relates to an all-optical sensor utilizing effective index modulation of a waveguide and detection of a wavelength shift of reflected light and a force sensing system accommodating said optical sensor. One embodiment of the invention relates to a sensor system comprising...... at least one multimode light source, one or more optical sensors comprising a multimode sensor optical waveguide accommodating a distributed Bragg reflector, at least one transmitting optical waveguide for guiding light from said at least one light source to said one or more multimode sensor optical...... waveguides, a detector for measuring light reflected from said Bragg reflector in said one or more multimode sensor optical waveguides, and a data processor adapted for analyzing variations in the Bragg wavelength of at least one higher order mode of the reflected light....

  9. Digital Sensor Technology

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, Ken D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Quinn, Edward L. [Technology Resources, Dana Point, CA (United States); Mauck, Jerry L. [Technology Resources, Dana Point, CA (United States); Bockhorst, Richard M. [Technology Resources, Dana Point, CA (United States)

    2015-02-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy and reliability. This paper, which refers to a final report issued in 2013, demonstrates these benefits in direct comparisons of digital and analog sensor applications. Improved accuracy results from the superior operating characteristics of digital sensors. These include improvements in sensor accuracy and drift and other related parameters which reduce total loop uncertainty and thereby increase safety and operating margins. An example instrument loop uncertainty calculation for a pressure sensor application is presented to illustrate these improvements. This is a side-by-side comparison of the instrument loop uncertainty for both an analog and a digital sensor in the same pressure measurement application. Similarly, improved sensor reliability is illustrated with a sample calculation for determining the probability of failure on demand, an industry standard reliability measure. This looks at equivalent analog and digital temperature sensors to draw the comparison. The results confirm substantial reliability improvement with the digital sensor, due in large part to ability to continuously monitor the health of a digital sensor such that problems can be immediately identified and corrected. This greatly reduces the likelihood of a latent failure condition of the sensor at the time of a design basis event. Notwithstanding the benefits of digital sensors, there are certain qualification issues that are inherent with digital technology and these are described in the report. One major qualification impediment for digital sensor implementation is software common cause failure (SCCF).

  10. El Derecho como argumentación

    OpenAIRE

    Atienza, Manuel

    1999-01-01

    Not available

    Frente a las concepciones del Derecho como norma, como hecho o como valor (que caracterizan, respectivamente, al norrnativismo, al realismo jurídico y al iusnaturalismo), se propone aquí un cuarto enfoque que consiste en ver el Derecho como argumentación (y que cohra especial relevancia en las sociedades democráticas). Sin embargo, no hay una única forma de entender la argumentación jurídica. Aunque conectadas entre sí, en el trabajo se distinguen tres concepc...

  11. Como responder ao momento presente?

    Directory of Open Access Journals (Sweden)

    Maria Filomena Molder

    2013-12-01

    Full Text Available http://dx.doi.org/10.5007/1984-784X.2013v13n19p13 Foi com esta pergunta — já um efeito de um primeiro encontro entre Irene Pimentel e eu própria — que decidimos desafiar colegas, estudantes e funci­onários da nossa Faculdade, FCSH (Faculdade de Ciências Sociais e Huma­nas, de outras Faculdades da Universidade Nova de Lisboa, de outras Uni­versidades e todos os interessados em con­siderar e discutir em comum aquilo que se passava em Portugal e que no anúncio da Jornada de 6 de De­zembro de 2012 se descrevia como um “processo de desmantela­mento social, económico e cultural sem precedentes — pese embora tantas compara­ções, baseadas na premissa da ‘eterna repetição’ — e cujas consequências não param de exceder as previsões dos responsáveis por esse desmantelamento”. Acedendo com todo o empenho e gratidão ao convite que me foi dirigido por Humberto Brito para fazer uma resenha da Jornada a publicar no primeiro número de Forma de Vida (saúdo a revista e o título, decidi-me, no entanto, a pôr de lado a resenha, que sob a forma de “Editorial” será em breve publi­cada no blogue Responder ao Momento Presente, entre­tanto criado, conjuntamente com os textos escritos pelos nossos convidados, com as parti­cipações de pessoas que corresponderam ao nosso apelo e ainda com contri­bui­ções que se alargaram para lá da Jornada; a que se juntará uma gravação em video, também disponível no Youtube.   Texto publicado originalmente em Forma de Vida, Lisboa, n.1, fev. 2013. Agrade­cemos à autora por permitir a republicação neste número do Boletim. [N.E.

  12. Como responder ao momento presente?

    Directory of Open Access Journals (Sweden)

    Maria Filomena Molder

    2013-06-01

    Full Text Available Foi com esta pergunta — já um efeito de um primeiro encontro entre Irene Pimentel e eu própria — que decidimos desafiar colegas, estudantes e funci­onários da nossa Faculdade, FCSH (Faculdade de Ciências Sociais e Huma­nas, de outras Faculdades da Universidade Nova de Lisboa, de outras Uni­versidades e todos os interessados em con­siderar e discutir em comum aquilo que se passava em Portugal e que no anúncio da Jornada de 6 de De­zembro de 2012 se descrevia como um “processo de desmantela­mento social, económico e cultural sem precedentes — pese embora tantas compara­ções, baseadas na premissa da ‘eterna repetição’ — e cujas consequências não param de exceder as previsões dos responsáveis por esse desmantelamento”. Acedendo com todo o empenho e gratidão ao convite que me foi dirigido por Humberto Brito para fazer uma resenha da Jornada a publicar no primeiro número de Forma de Vida (saúdo a revista e o título, decidi-me, no entanto, a pôr de lado a resenha, que sob a forma de “Editorial” será em breve publi­cada no blogue Responder ao Momento Presente, entre­tanto criado, conjuntamente com os textos escritos pelos nossos convidados, com as parti­cipações de pessoas que corresponderam ao nosso apelo e ainda com contri­bui­ções que se alargaram para lá da Jornada; a que se juntará uma gravação em video, também disponível no Youtube. Texto publicado originalmente em Forma de Vida, Lisboa, n.1, fev. 2013. Agrade­cemos à autora por permitir a republicação neste número do Boletim. [N.E.

  13. HEAT Sensor: Harsh Environment Adaptable Thermionic Sensor

    Energy Technology Data Exchange (ETDEWEB)

    Limb, Scott J. [Palo Alto Research Center, Palo Alto, CA (United States)

    2016-05-31

    This document is the final report for the “HARSH ENVIRONMENT ADAPTABLE THERMIONIC SENSOR” project under NETL’s Crosscutting contract DE-FE0013062. This report addresses sensors that can be made with thermionic thin films along with the required high temperature hermetic packaging process. These sensors can be placed in harsh high temperature environments and potentially be wireless and self-powered.

  14. Sensor for metal detection

    KAUST Repository

    Kodzius, Rimantas

    2014-06-26

    NOVELTY - The sensor has a microfluidic flow channel that is provided with an inlet port, an outlet port, and a detection chamber. The detection chamber is provided with a group of sensing electrodes (4) having a working electrode (8), a counter electrode (9), and a reference electrode (10). A flow sensor is configured to measure flow in the channel. A temperature sensor (6) is configured to measure temperature in the channel (3). An electrical connection is configured to connect the sensor to a sensing device. USE - Sensor for detecting metal such as toxic metal in sample such as clinical sample such as stool, saliva, sputum, bronchial lavage, urine, vaginal swab, nasal swab, biopsy, tissue, tears, breath, blood, serum, plasma, cerebrospinal fluid, peritoneal fluid, pleural fluid, pericardial fluid, joint fluid, and amniotic fluid, water sample, food sample, air sample, and soil sample (all claimed). ADVANTAGE - The sensor for use with the portable analytical instrument is configured for detection of metalsin samples. The sensor can provide the excellent solution for on-site metal detection, including heavy metal detection. The sensors can provide significant advantages in higher throughput, lower cost, at the same time being less labor intensive and less dependent on individual skills. The disposable design of the sensor, the enhanced reliability and repeatability of measurements can be obtained. The sensors can be widely applied in various industries. DETAILED DESCRIPTION - INDEPENDENT CLAIMS are included for the following: (1) a system for detecting metal in sample; and (2) a method for using sensor for detecting metal in sample. DESCRIPTION OF DRAWING(S) - The drawing shows a schematic view of the sensor prototype. Channel (3) Sensing electrodes (4) Temperature sensor (6) Working electrode (8) Counter electrode (9) Reference electrode (10)

  15. Estudio y pruebas de campo de WUSNs (Wireless Underground Sensor Networks)

    OpenAIRE

    Merino Garrido, Samuel

    2007-01-01

    Las redes de sensores son un campo de investigación muy activo. La gran variedad de aplicaciones que poseen en distintos campos induce a pensar que funcionarían correctamente para monitorizar entornos subterráneos. Por ejemplo, la agricultura utiliza los sensores subterráneos para supervisar condiciones del suelo tales como agua y contenido mineral. Los sensores también se utilizan con éxito para supervisar la integridad de las infraestructuras del subsuelo tales como tuber...

  16. MITRE sensor layer prototype

    Science.gov (United States)

    Duff, Francis; McGarry, Donald; Zasada, David; Foote, Scott

    2009-05-01

    The MITRE Sensor Layer Prototype is an initial design effort to enable every sensor to help create new capabilities through collaborative data sharing. By making both upstream (raw) and downstream (processed) sensor data visible, users can access the specific level, type, and quantities of data needed to create new data products that were never anticipated by the original designers of the individual sensors. The major characteristic that sets sensor data services apart from typical enterprise services is the volume (on the order of multiple terabytes) of raw data that can be generated by most sensors. Traditional tightly coupled processing approaches extract pre-determined information from the incoming raw sensor data, format it, and send it to predetermined users. The community is rapidly reaching the conclusion that tightly coupled sensor processing loses too much potentially critical information.1 Hence upstream (raw and partially processed) data must be extracted, rapidly archived, and advertised to the enterprise for unanticipated uses. The authors believe layered sensing net-centric integration can be achieved through a standardize-encapsulate-syndicateaggregate- manipulate-process paradigm. The Sensor Layer Prototype's technical approach focuses on implementing this proof of concept framework to make sensor data visible, accessible and useful to the enterprise. To achieve this, a "raw" data tap between physical transducers associated with sensor arrays and the embedded sensor signal processing hardware and software has been exploited. Second, we encapsulate and expose both raw and partially processed data to the enterprise within the context of a service-oriented architecture. Third, we advertise the presence of multiple types, and multiple layers of data through geographic-enabled Really Simple Syndication (GeoRSS) services. These GeoRSS feeds are aggregated, manipulated, and filtered by a feed aggregator. After filtering these feeds to bring just the type

  17. Development of electrochemical sensors based on nanostructured carbon materials for health-care applications

    OpenAIRE

    Abellán-Llobregat, Alejandra

    2017-01-01

    La presente Tesis Doctoral tiene como objetivo principal el desarrollo y funcionalización de diversos materiales carbonosos para su posterior aplicación como elemento transductor en sensores y biosensores electroquímicos. En este trabajo se ha evaluado el efecto de emplear diferentes materiales carbonosos como elementos transductores en sensores voltamétricos y cronoamperométricos para la cuantificación de ácido ascórbico y ácido úrico en fluidos fisiológicos humanos (e.g., orina, sudor, suer...

  18. Thin films for gas sensors

    Science.gov (United States)

    Pires, Jose Miguel Alves Correia

    Nos ultimos anos tem-se assistido a um aumento dos investimentos na investigacao de novos materiais para aplicacao em sensores. Apesar de ja existir um bom numero de dispositivos explorados comercialmente, muitas vezes, quer devido aos elevados custos de producao, quer devido a uma crescente exigencia do ponto de vista das caracteristicas de funcionamento, continua a ser necessario procurar novos materiais ou novas formas de producao que permitam baixar os custos e melhorar o desempenho dos dispositivos. No campo dos sensores de gases tem-se verificado continuos avancos nos ultimos anos. Continua todavia a ser necessario conhecer melhor, tanto os processos de producao dos materiais, como os mecanismos que regulam a sensibilidade dos dispositivos aos gases, de modo a orientar adequadamente a investigacao dos novos materiais, nomeadamente no que se refere a optimizacao dos parâmetros que nao satisfazem ainda os requisitos do mercado. Um dos materiais que tem mostrado melhores qualidades para aplicacao em sensores de gases de tipo resistivo e o dioxido de estanho. Este material tem sido produzido sob diversas formas e usando diferentes tecnicas, como sejam: sol-gel [1], pulverizacao catodica (sputtering) por magnetrao [2-4], sinterizacao de pos [5, 6], ablacao laser [7] ou RGTO [8]. Os resultados obtidos revelam que as caracteristicas dos dispositivos sao muito dependentes das tecnicas usadas na sua producao. A deposicao usando sputtering reactivo por magnetrao e uma tecnica que permite obter filmes finos de oxido de estanho com diferentes caracteristicas, quer do ponto de vista da estrutura, quer da composicao, e por isso, tambem, com diferentes sensibilidades aos gases. No âmbito deste trabalho, foram produzidos filmes de SnO2 usando sputtering DC reactivo com diferentes condicoes de deposicao. Os substratos usados foram lâminas de vidro e o alvo foi estanho com 99.9% de pureza. Foi estudada a influencia da atmosfera de deposicao, da pressao parcial do O2, da

  19. Sensor Network Motes:

    DEFF Research Database (Denmark)

    Leopold, Martin

    . In addition, we present our results from porting the highly popular sensor network operating system TinyOS to a new and emerging system on a chip based platform. Moving the sensor network field towards the use of system-on- a-chip devices has large potential in terms of price and performance. We claim to have......This dissertation describes our efforts to improve sensor network performance evaluation and portability, within the context of the sensor network project Hogthrob. In Hogthrob, we faced the challenge of building an sensor network architecture for sow monitoring. This application has hard...... requirements on price and performance, and shows great potential for using sensor networks. Throughout the project we let the application requirements guide our design choices, leading us to push the technologies further to meet the specific goal of the application. In this dissertation, we attack two key...

  20. Intelligent Sensors Security

    Directory of Open Access Journals (Sweden)

    Andrzej Bialas

    2010-01-01

    Full Text Available The paper is focused on the security issues of sensors provided with processors and software and used for high-risk applications. Common IT related threats may cause serious consequences for sensor system users. To improve their robustness, sensor systems should be developed in a restricted way that would provide them with assurance. One assurance creation methodology is Common Criteria (ISO/IEC 15408 used for IT products and systems. The paper begins with a primer on the Common Criteria, and then a general security model of the intelligent sensor as an IT product is discussed. The paper presents how the security problem of the intelligent sensor is defined and solved. The contribution of the paper is to provide Common Criteria (CC related security design patterns and to improve the effectiveness of the sensor development process.

  1. Clementine sensor suite

    Energy Technology Data Exchange (ETDEWEB)

    Ledebuhr, A.G. [Lawrence Livermore National Lab., CA (United States)

    1994-11-15

    LLNL designed and built the suite of six miniaturized light-weight space-qualified sensors utilized in the Clementine mission. A major goal of the Clementine program was to demonstrate technologies originally developed for Ballistic Missile Defense Organization Programs. These sensors were modified to gather data from the moon. This overview presents each of these sensors and some preliminary on-orbit performance estimates. The basic subsystems of these sensors include optical baffles to reject off-axis stray light, light-weight ruggedized optical systems, filter wheel assemblies, radiation tolerant focal plane arrays, radiation hardened control and readout electronics and low mass and power mechanical cryogenic coolers for the infrared sensors. Descriptions of each sensor type are given along with design specifications, photographs and on-orbit data collected.

  2. Working Group Report: Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Artuso, M.; et al.,

    2013-10-18

    Sensors play a key role in detecting both charged particles and photons for all three frontiers in Particle Physics. The signals from an individual sensor that can be used include ionization deposited, phonons created, or light emitted from excitations of the material. The individual sensors are then typically arrayed for detection of individual particles or groups of particles. Mounting of new, ever higher performance experiments, often depend on advances in sensors in a range of performance characteristics. These performance metrics can include position resolution for passing particles, time resolution on particles impacting the sensor, and overall rate capabilities. In addition the feasible detector area and cost frequently provides a limit to what can be built and therefore is often another area where improvements are important. Finally, radiation tolerance is becoming a requirement in a broad array of devices. We present a status report on a broad category of sensors, including challenges for the future and work in progress to solve those challenges.

  3. Capacitive chemical sensor

    Science.gov (United States)

    Manginell, Ronald P; Moorman, Matthew W; Wheeler, David R

    2014-05-27

    A microfabricated capacitive chemical sensor can be used as an autonomous chemical sensor or as an analyte-sensitive chemical preconcentrator in a larger microanalytical system. The capacitive chemical sensor detects changes in sensing film dielectric properties, such as the dielectric constant, conductivity, or dimensionality. These changes result from the interaction of a target analyte with the sensing film. This capability provides a low-power, self-heating chemical sensor suitable for remote and unattended sensing applications. The capacitive chemical sensor also enables a smart, analyte-sensitive chemical preconcentrator. After sorption of the sample by the sensing film, the film can be rapidly heated to release the sample for further analysis. Therefore, the capacitive chemical sensor can optimize the sample collection time prior to release to enable the rapid and accurate analysis of analytes by a microanalytical system.

  4. Flexible magnetoimpedance sensor

    KAUST Repository

    Li, Bodong

    2015-03-01

    Flexible magnetoimpedance (MI) sensors fabricated using a NiFe/Cu/NiFe tri-layer on Kapton substrate have been studied. A customized flexible microstrip transmission line was employed to investigate the MI sensors\\'s magnetic field and frequency responses and their dependence on the sensors\\'s deflection. For the first time, the impedance characteristic is obtained through reflection coefficient analysis over a wide range of frequencies from 0.1 MHz to 3 GHz and for deflections ranging from zero curvature to a radius of 7.2 cm. The sensor element maintains a high MI ratio of up to 90% and magnetic sensitivity of up to 9.2%/Oe over different bending curvatures. The relationship between the curvature and material composition is discussed based on the magnetostriction effect and stress simulations. The sensor\\'s large frequency range, simple fabrication process and high sensitivity provide a great potential for flexible electronics and wireless applications.

  5. Intelligent Sensors Security

    Science.gov (United States)

    Bialas, Andrzej

    2010-01-01

    The paper is focused on the security issues of sensors provided with processors and software and used for high-risk applications. Common IT related threats may cause serious consequences for sensor system users. To improve their robustness, sensor systems should be developed in a restricted way that would provide them with assurance. One assurance creation methodology is Common Criteria (ISO/IEC 15408) used for IT products and systems. The paper begins with a primer on the Common Criteria, and then a general security model of the intelligent sensor as an IT product is discussed. The paper presents how the security problem of the intelligent sensor is defined and solved. The contribution of the paper is to provide Common Criteria (CC) related security design patterns and to improve the effectiveness of the sensor development process. PMID:22315571

  6. The Ringcore Fluxgate Sensor

    DEFF Research Database (Denmark)

    Brauer, Peter

    1997-01-01

    A model describing the fundamental working principle of the "ringcore fluxgate sensor" is derived. The model is solely based on geometrical and measurable magnetic properties of the sensor and from this a number of fluxgate phenomenon can be described and estimated. The sensitivity of ringcore...... fluxgate sensors is measured for a large variety of geometries and is for all measurements found to fall between two limits obtained by the fluxgate model. The model is used to explain the zero field odd harmonic output of the fluxgate sensor, called the "feedthrough". By assuming a non ideal sensor...... with spatially distributed magnetization, the model predicts feedthrough signals which exactly reflects the measured signals. The non-linearities in a feedback compensated ringcore fluxgate sensors, called the "transverse field effect", can also be explained by the model. Measurements on stress annealed...

  7. Magnetic actuators and sensors

    CERN Document Server

    Brauer, John R

    2014-01-01

    An accessible, comprehensive guide on magnetic actuators and sensors, this fully updated second edition of Magnetic Actuators and Sensors includes the latest advances, numerous worked calculations, illustrations, and real-life applications. Covering magnetics, actuators, sensors, and systems, with updates of new technologies and techniques, this exemplary learning tool emphasizes computer-aided design techniques, especially magnetic finite element analysis, commonly used by today's engineers. Detailed calculations, numerous illustrations, and discussions of discrepancies make this text an inva

  8. Air Conditioning Overflow Sensor

    Science.gov (United States)

    1996-01-01

    The Technology Transfer Office at Stennis Space Center helped a local inventor develop a prototype of an attachment for central air conditioners and heat pumps that helps monitor water levels to prevent condensation overflow. The sensor will indicate a need for drain line maintenance and prevent possible damage caused by drain pan water spillover. An engineer in the Stennis Space Center prototype Development Laboratory used SSC sensor technology in the development of the sensor.

  9. Bioinspired Sensor Systems

    Directory of Open Access Journals (Sweden)

    Manel del Valle

    2011-10-01

    Full Text Available This editorial summarizes and classifies the contributions presented by different authors to the special issue of the journal Sensors dedicated to Bioinspired Sensor Systems. From the coupling of sensor arrays or networks, plus computer processing abilities, new applications to mimic or to complement human senses are arising in the context of ambient intelligence. Principles used, and illustrative study cases have been presented permitting readers to grasp the current status of the field.

  10. Contact stress sensor

    Science.gov (United States)

    Kotovsky, Jack

    2014-02-11

    A method for producing a contact stress sensor that includes one or more MEMS fabricated sensor elements, where each sensor element of includes a thin non-recessed portion, a recessed portion and a pressure sensitive element adjacent to the recessed portion. An electric circuit is connected to the pressure sensitive element. The circuit includes a pressure signal circuit element configured to provide a signal upon movement of the pressure sensitive element.

  11. Contact stress sensor

    Science.gov (United States)

    Kotovsky, Jack [Oakland, CA

    2012-02-07

    A contact stress sensor includes one or more MEMS fabricated sensor elements, where each sensor element of includes a thin non-recessed portion, a recessed portion and a pressure sensitive element adjacent to the recessed portion. An electric circuit is connected to the pressure sensitive element. The circuit includes a thermal compensator and a pressure signal circuit element configured to provide a signal upon movement of the pressure sensitive element.

  12. Transient multivariable sensor evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Vilim, Richard B.; Heifetz, Alexander

    2017-02-21

    A method and system for performing transient multivariable sensor evaluation. The method and system includes a computer system for identifying a model form, providing training measurement data, generating a basis vector, monitoring system data from sensor, loading the system data in a non-transient memory, performing an estimation to provide desired data and comparing the system data to the desired data and outputting an alarm for a defective sensor.

  13. Fiber optic temperature sensor

    Science.gov (United States)

    Sawatari, Takeo (Inventor); Gaubis, Philip A. (Inventor)

    2000-01-01

    A fiber optic temperature sensor uses a light source which transmits light through an optical fiber to a sensor head at the opposite end of the optical fiber from the light source. The sensor head has a housing coupled to the end of the optical fiber. A metallic reflective surface is coupled to the housing adjacent the end of the optical fiber to form a gap having a predetermined length between the reflective surface and the optical fiber. A detection system is also coupled to the optical fiber which determines the temperature at the sensor head from an interference pattern of light which is reflected from the reflective surface.

  14. Smart sensors and systems

    CERN Document Server

    Kyung, Chong-Min; Yasuura, Hiroto; Liu, Yongpan

    2015-01-01

     This book describes for readers technology used for effective sensing of our physical world and intelligent processing techniques for sensed information, which are essential to the success of Internet of Things (IoTs).  The authors provide a multidisciplinary view of sensor technology from MEMS, biological, chemical, and electrical domains and showcase smart sensor systems in real applications including smart home, transportation, medical, environmental, agricultural, etc.  Unlike earlier books on sensors, this book will provide a “global” view on smart sensors covering abstraction levels from device, circuit, systems, and algorithms.  .

  15. Improved Capacitive Liquid Sensor

    Science.gov (United States)

    Waldman, Francis A.

    1992-01-01

    Improved capacitive sensor used to detect presence and/or measure thickness of layer of liquid. Electrical impedance or admittance of sensor measured at prescribed frequency, and thickness of liquid inferred from predetermined theoretical or experimental relationship between impedance and thickness. Sensor is basically a three-terminal device. Features interdigitated driving and sensing electrodes and peripheral coplanar ground electrode that reduces parasitic effects. Patent-pending because first to utilize ground plane as "shunting" electrode. System less expensive than infrared, microwave, or refractive-index systems. Sensor successfully evaluated in commercial production plants to characterize emulsions, slurries, and solutions.

  16. Smart and Intelligent Sensors

    Science.gov (United States)

    Lansaw, John; Schmalzel, John; Figueroa, Jorge

    2009-01-01

    John C. Stennis Space Center (SSC) provides rocket engine propulsion testing for NASA's space programs. Since the development of the Space Shuttle, every Space Shuttle Main Engine (SSME) has undergone acceptance testing at SSC before going to Kennedy Space Center (KSC) for integration into the Space Shuttle. The SSME is a large cryogenic rocket engine that uses Liquid Hydrogen (LH2) as the fuel. As NASA moves to the new ARES V launch system, the main engines on the new vehicle, as well as the upper stage engine, are currently base lined to be cryogenic rocket engines that will also use LH2. The main rocket engines for the ARES V will be larger than the SSME, while the upper stage engine will be approximately half that size. As a result, significant quantities of hydrogen will be required during the development, testing, and operation of these rocket engines.Better approaches are needed to simplify sensor integration and help reduce life-cycle costs. 1.Smarter sensors. Sensor integration should be a matter of "plug-and-play" making sensors easier to add to a system. Sensors that implement new standards can help address this problem; for example, IEEE STD 1451.4 defines transducer electronic data sheet (TEDS) templates for commonly used sensors such as bridge elements and thermocouples. When a 1451.4 compliant smart sensor is connected to a system that can read the TEDS memory, all information needed to configure the data acquisition system can be uploaded. This reduces the amount of labor required and helps minimize configuration errors. 2.Intelligent sensors. Data received from a sensor be scaled, linearized; and converted to engineering units. Methods to reduce sensor processing overhead at the application node are needed. Smart sensors using low-cost microprocessors with integral data acquisition and communication support offer the means to add these capabilities. Once a processor is embedded, other features can be added; for example, intelligent sensors can make

  17. Test and fabrication of piezoresistive sensors for contact pressure measurement

    Directory of Open Access Journals (Sweden)

    Diego Andrés Valle-Lopera

    2017-01-01

    Full Text Available El uso de sensores de presión de contacto se ha popularizado en diferentes disciplinas de la ingeniería en los últimos años. Se utilizan en la caracterización de llantas para vehículos, rodamientos, túneles de viento, diseño de prótesis, análisis ergonómicos, entre otras áreas. Estos sensores, son diseñados con materiales que poseen ciertas propiedades tales como piezoelectricidad, piezorresistencia y capacitancia variable; sin embargo, la característica más usada es la piezorresistencia. En este artículo se describe la fabricación de tres sensores de presión diferentes usando materiales piezorresistivos. Adicionalmente, se realizó un estudio técnico comparativo incluyendo un sensor comercial usado como punto de referencia con el fin de seleccionar el material idóneo para medir presión por contacto. La repetibilidad y la histéresis de cada sensor fueron evaluadas en una prueba de respuesta a la carga realizada varias veces. También se llevó a cabo una prueba de desviación en el tiempo para evaluar estabilidad de la medición de un peso muerto. Los materiales como la tela o tinta piezoresistiva muestran ser adecuados para aplicaciones en las que haya deformación y se necesite de sensores flexibles, el Velostat es el menos preciso pero adecuado para aplicaciones básicas y en las cuales no se necesite de mucha resolución. Finalmente se presentan recomendaciones respecto al tipo de material que se debe utilizar en sensores de presión para diversas aplicaciones en ingeniería en general y en el campo biomédico en particular.

  18. Semantic Sensor Web

    Science.gov (United States)

    Sheth, A.; Henson, C.; Thirunarayan, K.

    2008-12-01

    Sensors are distributed across the globe leading to an avalanche of data about our environment. It is possible today to utilize networks of sensors to detect and identify a multitude of observations, from simple phenomena to complex events and situations. The lack of integration and communication between these networks, however, often isolates important data streams and intensifies the existing problem of too much data and not enough knowledge. With a view to addressing this problem, the Semantic Sensor Web (SSW) [1] proposes that sensor data be annotated with semantic metadata that will both increase interoperability and provide contextual information essential for situational knowledge. Kno.e.sis Center's approach to SSW is an evolutionary one. It adds semantic annotations to the existing standard sensor languages of the Sensor Web Enablement (SWE) defined by OGC. These annotations enhance primarily syntactic XML-based descriptions in OGC's SWE languages with microformats, and W3C's Semantic Web languages- RDF and OWL. In association with semantic annotation and semantic web capabilities including ontologies and rules, SSW supports interoperability, analysis and reasoning over heterogeneous multi-modal sensor data. In this presentation, we will also demonstrate a mashup with support for complex spatio-temporal-thematic queries [2] and semantic analysis that utilize semantic annotations, multiple ontologies and rules. It uses existing services (e.g., GoogleMap) and semantics enhanced SWE's Sensor Observation Service (SOS) over weather and road condition data from various sensors that are part of Ohio's transportation network. Our upcoming plans are to demonstrate end to end (heterogeneous sensor to application) semantics support and study scalability of SSW involving thousands of sensors to about a billion triples. Keywords: Semantic Sensor Web, Spatiotemporal thematic queries, Semantic Web Enablement, Sensor Observation Service [1] Amit Sheth, Cory Henson, Satya

  19. La sabidur?a como competencia gerencial

    OpenAIRE

    Pinzon-Barrios, Ana-Maria; Cort?s Zapata, Gabriela

    2012-01-01

    Aunque el concepto de sabidur?a ha sido ampliamente estudiado por expertos de ?reas como la filosof?a, la religi?n y la psicolog?a, a?n enfrenta limitaciones en cuanto a su definici?n y evaluaci?n. Por esto, el presente trabajo tiene como objetivo, formular una definici?n del concepto de sabidur?a que permita realizar una propuesta de evaluaci?n del concepto como competencia en los gerentes. Para esto, se realiz? un an?lisis documental de tipo cualitativo. De esta manera, se analizaron divers...

  20. Los ritmos como terapia para la impulsividad

    Directory of Open Access Journals (Sweden)

    Mónica Triviño

    2012-10-01

    Full Text Available Investigaciones recientes muestran que el uso de patrones rítmicos facilita la respuesta óptima en el tiempo, por lo que el entrenamiento mediante ritmos podría proponerse como terapia novedosa ante problemas como la impulsividad. Esto podría beneficiar a pacientes con daño prefrontal o personas con trastorno por déficit de atención e hiperactividad (TDAH, que suelen mostrar conductas impulsivas, así como dificultad para estimar el paso del tiempo.

  1. Nickel coating electroplated characterization with and without carbon nanotubes; Caracterizacao de niquel eletrodepositado na presenca de nanotubos de carbono

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, A.C.; Banczek, E.P.; Cunha, M.T.; Rodrigues, P.R.P. [Universidade Estadual do Centro-Oeste, Guarapuava, PR (Brazil). Dept. de Quimica; Costa, I. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Terada, M. [Universidade de Sao Paulo (EPUSP), SP (Brazil). Escola Politecnica. Dept. de Engenharia Metalurgica e de Materiais

    2010-07-01

    The metals have great application, but when their properties are not suitable they should be improved through treatments to increase corrosion resistance, mechanical and wear. The metals electrodeposition such as nickel is one of treatment options. This study aims the development a nickel coating with and without (CNT), obtained by electrodeposition on aluminum alloy AA6061. The nickel electrodeposition was performed with cyclic voltammetry and chronoamperometry. Open circuit potential and anodic polarization curves were carried out samples characterization. The microstructure and the chemical composition of the M{sub x}O{sub z} coating were studied using the scanning electron microscopy, energy dispersion spectroscopy and X-ray diffraction. The results indicated that the nickel coating improve the corrosion resistance of aluminum in the presence of CNT. (author)

  2. Potentiometric anion selective sensors

    NARCIS (Netherlands)

    Antonisse, M.M.G.; Reinhoudt, David

    1999-01-01

    In comparison with selective receptors (and sensors) for cationic species, work on the selective complexation and detection of anions is of more recent date. There are three important components for a sensor, a transducer element, a membrane material that separates the transducer element and the

  3. Sensors in Education

    NARCIS (Netherlands)

    Van Rosmalen, Peter; Schneider, Jan; Börner, Dirk

    2014-01-01

    Sensors rapidly become available both for personal as well as scientific use. A wide range of applications exists for personal use e.g. safety in and around the house, sport, fitness and health. In this workshop we will explore how sensors are (can be) used in education. We start with an

  4. Wireless Sensors Network (Sensornet)

    Science.gov (United States)

    Perotti, J.

    2003-01-01

    The Wireless Sensor Network System presented in this paper provides a flexible reconfigurable architecture that could be used in a broad range of applications. It also provides a sensor network with increased reliability; decreased maintainability costs, and assured data availability by autonomously and automatically reconfiguring to overcome communication interferences.

  5. Sensor Data Fusion

    DEFF Research Database (Denmark)

    Plascencia, Alfredo; Stepán, Petr

    2006-01-01

    The main contribution of this paper is to present a sensor fusion approach to scene environment mapping as part of a Sensor Data Fusion (SDF) architecture. This approach involves combined sonar array with stereo vision readings.  Sonar readings are interpreted using probability density functions...

  6. Stretch Sensor Device

    DEFF Research Database (Denmark)

    2013-01-01

    The invention relates to a method for determining stretch values and movement of body parts, e.g. a foot, by analysing stretch data from a stretch sensor. By analysing data from the stretch sensor it is possible to determine stretch samples which are associated with particular motion phases...

  7. 2-Sensor Problem

    Directory of Open Access Journals (Sweden)

    Michael Segal

    2004-11-01

    Full Text Available Abstract: Ad-hoc networks of sensor nodes are in general semi-permanently deployed. However, the topology of such networks continuously changes over time, due to the power of some sensors wearing out to new sensors being inserted into the network, or even due to designers moving sensors around during a network re-design phase (for example, in response to a change in the requirements of the network. In this paper, we address the problem of covering a given path by a limited number of sensors — in our case to two, and show its relation to the well-studied matrix multiplication problem.

  8. Fiber optic gas sensor

    Science.gov (United States)

    Chen, Peng (Inventor); Buric, Michael P. (Inventor); Swinehart, Philip R. (Inventor); Maklad, Mokhtar S. (Inventor)

    2010-01-01

    A gas sensor includes an in-fiber resonant wavelength device provided in a fiber core at a first location. The fiber propagates a sensing light and a power light. A layer of a material is attached to the fiber at the first location. The material is able to absorb the gas at a temperature dependent gas absorption rate. The power light is used to heat the material and increases the gas absorption rate, thereby increasing sensor performance, especially at low temperatures. Further, a method is described of flash heating the gas sensor to absorb more of the gas, allowing the sensor to cool, thereby locking in the gas content of the sensor material, and taking the difference between the starting and ending resonant wavelengths as an indication of the concentration of the gas in the ambient atmosphere.

  9. Reconocimiento de actividad mediante pulsera con sensores

    OpenAIRE

    Aguilera Calle, Iván; García Moreno, Daniel; Morante Pindado, Verónica; Pidal Gallego, Alejandro

    2017-01-01

    Desde hace unos años, con el desarrollo de los smartphones y actualmente con el auge del internet de las cosas, la tecnología ha invadido gran parte de nuestra vida como en campos de la salud, el deporte o el bienestar. Este trabajo se centra en los dos últimos aspectos con el fin de hacer una app para smartphone de reconocimiento de actividad mediante sensores, con el que se busca conseguir que las personas lleven un control de las actividades que hacen a lo largo del día, pudiendo tener un ...

  10. El videojuego como material educativo: La Odisea

    Directory of Open Access Journals (Sweden)

    Belén Mainer Blanco

    2012-04-01

    Full Text Available La investigación se basa en la función educativa que pueden cumplir los videojuegos, un campo que consideramos inexplorado por tres motivos principalmente: su reciente incorporación, su impopularidad educativa (el rechazo el videojuego como herramienta de aprendizaje y considerado, por el contrario, como una distracción, y la incompleta incorporación de las nuevas tecnologías de información y comunicación (TIC en el ámbito familiar y educativo. En una segunda parte, se ha realizado una aplicación práctica tomando como referencia la gran obra universal “La Odisea”, cuya intención es mostrar la utilidad del videojuego como complemento educativo.

  11. El rock como conformador de identidades juveniles

    National Research Council Canada - National Science Library

    Adrián de Garay

    1996-01-01

    El autor analiza la relación entre el rock y las identidades juveniles, a partir del abordaje de cinco "estilos" que se pueden identificar como constitutivos de éstas identidades. Ellos son: la jerga...

  12. El Derecho como argumentación

    Directory of Open Access Journals (Sweden)

    Atienza, Manuel

    1999-11-01

    Full Text Available Not available

    Frente a las concepciones del Derecho como norma, como hecho o como valor (que caracterizan, respectivamente, al norrnativismo, al realismo jurídico y al iusnaturalismo, se propone aquí un cuarto enfoque que consiste en ver el Derecho como argumentación (y que cohra especial relevancia en las sociedades democráticas. Sin embargo, no hay una única forma de entender la argumentación jurídica. Aunque conectadas entre sí, en el trabajo se distinguen tres concepciones: la formal, la material y la pragmática o dialéctica; muchas cuestiones que se plantean en el ámbito de la teoría de la argumentación jurídica pueden resolverse -o aclararse- teniendo en cuenta esa triple perspectiva.

  13. Underwater sensor nodes and networks

    National Research Council Canada - National Science Library

    Lloret, Jaime

    2013-01-01

    .... This special issue is focused on collecting recent advances on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments...

  14. Las leyendas regionales como intangibles territoriales

    Directory of Open Access Journals (Sweden)

    Eloy Martos Núñez

    2015-01-01

    Full Text Available El artículo examina el concepto de leyenda como intangible territorial en diversas escalas, desde la local a la regional o nacional, y su relación con la construcción de mitos étnicos y la emergencia de tradiciones translocales. Para ello, se revisan la metodología de los estudios corográficos y las nociones de ecotipo y de paisaje cultural, así como la etnografía de los territorios simbólicos a la luz de conceptos como el clásico «témenos» y modernos como el «mytho-moteur» (Abadal, 1958. Se aplican estudios de casos que evidencian cómo es el Imaginario, en interacción con factores geohistóricos del lugar, el que a menudo acota y perimetrea un territorio a través de cauces como la fabulación legendaria y los ritos paralitúgicos, como procesiones o peregrinaciones. La conclusión es que las leyendas y los arquetipos de origen étnico y genealógico reescriben tradiciones que crean identidades y se pueden proyectar en ámbitos diferentes de la vida política o recreativa, con perfiles igualmente diferentes.

  15. El humor como herramienta para lograr aprendizajes

    Directory of Open Access Journals (Sweden)

    Hilda Torres de Sánchez

    2003-09-01

    Full Text Available Una tendencia mundial se ha originado: el uso del humor como herramienta para lograr aprendizajes y mejorar el ambiente donde la persona se encuentre. En el área educativa hay pruebas que demuestran su utilidad y que efectivamente origina cambios positivos, medidos en las evaluaciones, tanto en los estudiantes como en participantes de sesiones de facilitación. El objetivo del experimento realizado fue: Determinar el comportamiento a través de la calificaciones en la primera prueba, del efecto del uso del humor en el dictado de clases utilizando diferentes herramientas como: chistes, anécdotas, analogías en los contenidos. A través de un estudio experimental con un grupo de control realizado en dos aulas de clases con 35 alumnos cada uno, al grupo experimental se le aplicó diferentes recursos humorísticos como herramientas de aprendizaje. Se analizaron las calificaciones en la primera prueba a través de porcentajes de aprobados y aplazados, observándose que el grupo experimental arrojó los mayores porcentajes de aprobados. Tales resultados confirman que el humor como herramienta, si induce a un desempeño excelente en alumnos, lo que lleva a implementar acciones de adiestramiento para los facilitadores, así como el surgimiento de investigaciones más profundas sobre el uso del humor en la educación.

  16. Roadmap on optical sensors

    Science.gov (United States)

    Ferreira, Mário F. S.; Castro-Camus, Enrique; Ottaway, David J.; López-Higuera, José Miguel; Feng, Xian; Jin, Wei; Jeong, Yoonchan; Picqué, Nathalie; Tong, Limin; Reinhard, Björn M.; Pellegrino, Paul M.; Méndez, Alexis; Diem, Max; Vollmer, Frank; Quan, Qimin

    2017-08-01

    Sensors are devices or systems able to detect, measure and convert magnitudes from any domain to an electrical one. Using light as a probe for optical sensing is one of the most efficient approaches for this purpose. The history of optical sensing using some methods based on absorbance, emissive and florescence properties date back to the 16th century. The field of optical sensors evolved during the following centuries, but it did not achieve maturity until the demonstration of the first laser in 1960. The unique properties of laser light become particularly important in the case of laser-based sensors, whose operation is entirely based upon the direct detection of laser light itself, without relying on any additional mediating device. However, compared with freely propagating light beams, artificially engineered optical fields are in increasing demand for probing samples with very small sizes and/or weak light-matter interaction. Optical fiber sensors constitute a subarea of optical sensors in which fiber technologies are employed. Different types of specialty and photonic crystal fibers provide improved performance and novel sensing concepts. Actually, structurization with wavelength or subwavelength feature size appears as the most efficient way to enhance sensor sensitivity and its detection limit. This leads to the area of micro- and nano-engineered optical sensors. It is expected that the combination of better fabrication techniques and new physical effects may open new and fascinating opportunities in this area. This roadmap on optical sensors addresses different technologies and application areas of the field. Fourteen contributions authored by experts from both industry and academia provide insights into the current state-of-the-art and the challenges faced by researchers currently. Two sections of this paper provide an overview of laser-based and frequency comb-based sensors. Three sections address the area of optical fiber sensors, encompassing both

  17. Roadmap on optical sensors.

    Science.gov (United States)

    Ferreira, Mário F S; Castro-Camus, Enrique; Ottaway, David J; López-Higuera, José Miguel; Feng, Xian; Jin, Wei; Jeong, Yoonchan; Picqué, Nathalie; Tong, Limin; Reinhard, Björn M; Pellegrino, Paul M; Méndez, Alexis; Diem, Max; Vollmer, Frank; Quan, Qimin

    2017-08-01

    Sensors are devices or systems able to detect, measure and convert magnitudes from any domain to an electrical one. Using light as a probe for optical sensing is one of the most efficient approaches for this purpose. The history of optical sensing using some methods based on absorbance, emissive and florescence properties date back to the 16th century. The field of optical sensors evolved during the following centuries, but it did not achieve maturity until the demonstration of the first laser in 1960. The unique properties of laser light become particularly important in the case of laser-based sensors, whose operation is entirely based upon the direct detection of laser light itself, without relying on any additional mediating device. However, compared with freely propagating light beams, artificially engineered optical fields are in increasing demand for probing samples with very small sizes and/or weak light-matter interaction. Optical fiber sensors constitute a subarea of optical sensors in which fiber technologies are employed. Different types of specialty and photonic crystal fibers provide improved performance and novel sensing concepts. Actually, structurization with wavelength or subwavelength feature size appears as the most efficient way to enhance sensor sensitivity and its detection limit. This leads to the area of micro- and nano-engineered optical sensors. It is expected that the combination of better fabrication techniques and new physical effects may open new and fascinating opportunities in this area. This roadmap on optical sensors addresses different technologies and application areas of the field. Fourteen contributions authored by experts from both industry and academia provide insights into the current state-of-the-art and the challenges faced by researchers currently. Two sections of this paper provide an overview of laser-based and frequency comb-based sensors. Three sections address the area of optical fiber sensors, encompassing both

  18. Use of NMR as an online sensor in industrial processes; Uso da RMN como um sensor online em processos industriais

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Fabiana Diuk de [Universidade de Sao Paulo (IQSC/USP), Sao Carlos, SP (Brazil). Inst. de Quimica; Colnago, Luiz Alberto, E-mail: colnago@cnpdia.embrapa.br [Embrapa Instrumentacao, Sao Carlos, SP (Brazil)

    2012-07-01

    Nuclear magnetic resonance (NMR) is one of the most versatile analytical techniques for chemical, biochemical and medical applications. Despite this great success, NMR is seldom used as a tool in industrial applications. The first application of NMR in flowing samples was published in 1951. However, only in the last ten years Flow NMR has gained momentum and new and potential applications have been proposed. In this review we present the historical evolution of flow or online NMR spectroscopy and imaging, and current developments for use in the automation of industrial processes. (author)

  19. Advanced Magnetoimpedance Sensors

    KAUST Repository

    Li, Bodong

    2015-02-01

    This thesis is concerned with the advanced topics of thin film magnetoimpedance (MI) sensors. The author proposes and develops novel MI sensors that target on the challenges arising from emerging applications such as flexible electronics, passive wireless sensing, etc. In the study of flexible MI sensor, the investigated sensors of NiFe/Cu/NiFe tri-layersare fabricated on three flexible substrates having different surface roughness: Kapton, standard and premiumphotopaper. Sensitivity versus substrate roughness analysis is carried out for the selection of optimal substrate material. The high magnetic sensing performance is achieved by using Kapton substrate. Stress simulation, incorporated with the theory of magnetostriction effect, reveals the material composition of Ni/Fe being as a key factor of the stress dependent MI effect for the flexible MI sensors. In the development of MI-SAW device for passive wireless magnetic field sensing, NiFe/Cu/NiFe tri-layersand interdigital transducers(IDT) are designed and fabricated on a single piece of LiNbO3substrate, providing a high degree of integration and the advantage of standard microfabrication. The double-electrodeIDT has been utilized and proven to have an optimal sensing performance in comparison to the bi-directional IDT design. The optimized high frequency performance of the thin film MI sensor results in a MI-SAW passive wireless magnetic sensor with high magnetic sensitivity comparing to the MI microwire approach. Benefiting from the high degree of integration of the MI thin film element, in the following study, two additional sensing elements are integrated to the SAW device to have a multifunctional passive wireless sensor with extended temperature and humidity sensing capabilities. Analytical models havebeen developed to eliminate the crossovers of different sensing signals through additional reference IDTs, resulting in a multifunctional passive wireless sensor with the capability of detecting all three

  20. Micro Coriolis mass flow sensor with integrated resistive pressure sensors

    NARCIS (Netherlands)

    Groenesteijn, Jarno; Alveringh, Dennis; Schut, Thomas; Wiegerink, Remco J.; Sparreboom, Wouter; Lötters, Joost Conrad

    2017-01-01

    We report on novel resistive pressure sensors, integrated on-chip at the inlet- and outlet-channels of a micro Coriolis mass flow sensor. The pressure sensors can be used to measure the pressure drop over the Coriolis sensor which can be used to compensate pressure-dependent behaviour that might

  1. Resistive pressure sensors integrated with a Coriolis mass flow sensor

    NARCIS (Netherlands)

    Alveringh, Dennis; Schut, Thomas; Wiegerink, Remco J.; Sparreboom, Wouter; Lötters, Joost Conrad

    2017-01-01

    We report on a novel resistive pressure sensor that is completely integrated with a Coriolis mass flow sensor on one chip, without the need for extra fabrication steps or different materials. Two pressure sensors are placed in-line with the Coriolis sensor without requiring any changes to the fluid

  2. Thermal Anemometry Grid Sensor

    Directory of Open Access Journals (Sweden)

    Martin Arlit

    2017-07-01

    Full Text Available A novel thermal anemometry grid sensor was developed for the simultaneous measurement of cross-sectional temperature and axial velocity distribution in a fluid flow. The sensor consists of a set of platinum resistors arranged in a regular grid. Each platinum resistor allows the simultaneous measurement of fluid temperature via electrical resistance and flow velocity via constant voltage thermal anemometry. Cross-sectional measurement was enabled by applying a special multiplexing-excitation scheme. In this paper, we present the design and characterization of a prototypical sensor for measurements in a range of very low velocities.

  3. Professional Android Sensor Programming

    CERN Document Server

    Milette, Greg

    2012-01-01

    Learn to build human-interactive Android apps, starting with device sensors This book shows Android developers how to exploit the rich set of device sensors—locational, physical (temperature, pressure, light, acceleration, etc.), cameras, microphones, and speech recognition—in order to build fully human-interactive Android applications. Whether providing hands-free directions or checking your blood pressure, Professional Android Sensor Programming shows how to turn possibility into reality. The authors provide techniques that bridge the gap between accessing sensors and putting the

  4. Thermal Anemometry Grid Sensor.

    Science.gov (United States)

    Arlit, Martin; Schleicher, Eckhard; Hampel, Uwe

    2017-07-19

    A novel thermal anemometry grid sensor was developed for the simultaneous measurement of cross-sectional temperature and axial velocity distribution in a fluid flow. The sensor consists of a set of platinum resistors arranged in a regular grid. Each platinum resistor allows the simultaneous measurement of fluid temperature via electrical resistance and flow velocity via constant voltage thermal anemometry. Cross-sectional measurement was enabled by applying a special multiplexing-excitation scheme. In this paper, we present the design and characterization of a prototypical sensor for measurements in a range of very low velocities.

  5. Characterization of Pixel Sensors

    CERN Document Server

    Oliveira, Felipe Ferraz

    2017-01-01

    It was commissioned at CERN ATLAS pixel group a fluorescence setup for characterization of pixel sensors. The idea is to measure the energies of different targets to calibrate your sensor. It was measured four matrices (80, 95, 98 and 106) of the Investigator1 sensor with different deep PW using copper, iron and titanium as target materials. The matrix 80 has a higher gain (0.065 ± 0.002) and matrix 106 has a better energy resolution (0.05 ± 0.04). The noise of the setup is around 3.6 mV .

  6. Flexible Plasmonic Sensors

    Science.gov (United States)

    Shir, Daniel; Ballard, Zachary S.; Ozcan, Aydogan

    2016-01-01

    Mechanical flexibility and the advent of scalable, low-cost, and high-throughput fabrication techniques have enabled numerous potential applications for plasmonic sensors. Sensitive and sophisticated biochemical measurements can now be performed through the use of flexible plasmonic sensors integrated into existing medical and industrial devices or sample collection units. More robust sensing schemes and practical techniques must be further investigated to fully realize the potentials of flexible plasmonics as a framework for designing low-cost, embedded and integrated sensors for medical, environmental, and industrial applications. PMID:27547023

  7. Sensor Suits for Human Motion Detection

    National Research Council Canada - National Science Library

    Feng, Maria Q

    2006-01-01

    ... shape, the stiffness and the density. This sensor suit is made of soft and elastic fabrics embedded with arrays of MEMS sensors such as muscle stiffness sensor, ultrasonic sensors, accelerometers and optical fiber sensors, to measure...

  8. Test and fabrication of piezoresistive sensors for contact pressure measurement

    OpenAIRE

    Diego Andrés Valle-Lopera; Andrés Felipe Castaño-Franco; Jonathan Gallego-Londoño; Alher Mauricio Hernández-Valdivieso

    2017-01-01

    El uso de sensores de presión de contacto se ha popularizado en diferentes disciplinas de la ingeniería en los últimos años. Se utilizan en la caracterización de llantas para vehículos, rodamientos, túneles de viento, diseño de prótesis, análisis ergonómicos, entre otras áreas. Estos sensores, son diseñados con materiales que poseen ciertas propiedades tales como piezoelectricidad, piezorresistencia y capacitancia variable; sin embargo, la característica más usada es la piezorresistencia. En ...

  9. Magnetic Nanocomposite Cilia Tactile Sensor

    KAUST Repository

    Alfadhel, Ahmed

    2015-10-21

    A multifunctional biomimetic nanocomposite tactile sensor is developed that can detect shear and vertical forces, feel texture, and measure flow with extremely low power consumption. The sensor\\'s high performance is maintained within a wide operating range that can be easily adjusted. The concept works on rigid and flexible substrates and the sensors can be used in air or water without any modifications.

  10. Sensor employing internal reference electrode

    DEFF Research Database (Denmark)

    2013-01-01

    The present invention concerns a novel internal reference electrode as well as a novel sensing electrode for an improved internal reference oxygen sensor and the sensor employing same.......The present invention concerns a novel internal reference electrode as well as a novel sensing electrode for an improved internal reference oxygen sensor and the sensor employing same....

  11. Multi-Sensor Architectures

    DEFF Research Database (Denmark)

    Hussain, Dil Muhammad Akbar; Ahmed, Zaki; Khan, M. Z.

    2012-01-01

    The use of multiple sensors typically requires the fusion of data from different type of sensors. The combined use of such a data has the potential to give an efficient, high quality and reliable estimation. Input data from different sensors allows the introduction of target attributes (target type......, size) into the association logic. This requires a more general association logic, in which both the physical position parameters and the target attributes can be used simultaneously. Although, the data fusion from a number of sensors could provide better and reliable estimation but abundance...... of information is to be handled. Therefore, more extensive computer resources are needed for such a system. The parallel processing technique could be an alternative for such a system. The main objective of this research is to provide a real time task allocation strategy for data processing using multiple...

  12. Magnetic Resonance Sensors

    Directory of Open Access Journals (Sweden)

    Robert H. Morris

    2014-11-01

    Full Text Available Magnetic Resonance finds countless applications, from spectroscopy to imaging, routinely in almost all research and medical institutions across the globe. It is also becoming more frequently used for specific applications in which the whole instrument and system is designed for a dedicated application. With beginnings in borehole logging for the petro-chemical industry Magnetic Resonance sensors have been applied to fields as varied as online process monitoring for food manufacture and medical point of care diagnostics. This great diversity is seeing exciting developments in magnetic resonance sensing technology published in application specific journals where they are often not seen by the wider sensor community. It is clear that there is enormous interest in magnetic resonance sensors which represents a significant growth area. The aim of this special edition of Sensors was to address the wide distribution of relevant articles by providing a forum to disseminate cutting edge research in this field in a single open source publication.[...

  13. Water Properties Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this Phase II project, Kaitech proposes to develop and demonstrate a Water Properties Sensor (WPS) sensing system to synchronously measure the spectral inherent...

  14. Reconfigurable Sensor Monitoring System

    Science.gov (United States)

    Alhorn, Dean C. (Inventor); Dutton, Kenneth R. (Inventor); Howard, David E. (Inventor); Smith, Dennis A. (Inventor)

    2017-01-01

    A reconfigurable sensor monitoring system includes software tunable filters, each of which is programmable to condition one type of analog signal. A processor coupled to the software tunable filters receives each type of analog signal so-conditioned.

  15. Graphene Chemical Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The sensor uses graphene based devices to sense the surface potential of a graphene channel exposed to an analyte. When analyte molecules adsorb onto the...

  16. Complex pendulum biomass sensor

    Science.gov (United States)

    Hoskinson, Reed L.; Kenney, Kevin L.; Perrenoud, Ben C.

    2007-12-25

    A complex pendulum system biomass sensor having a plurality of pendulums. The plurality of pendulums allow the system to detect a biomass height and density. Each pendulum has an angular deflection sensor and a deflector at a unique height. The pendulums are passed through the biomass and readings from the angular deflection sensors are fed into a control system. The control system determines whether adjustment of machine settings is appropriate and either displays an output to the operator, or adjusts automatically adjusts the machine settings, such as the speed, at which the pendulums are passed through the biomass. In an alternate embodiment, an entanglement sensor is also passed through the biomass to determine the amount of biomass entanglement. This measure of entanglement is also fed into the control system.

  17. Advanced laser sensors

    OpenAIRE

    Ebert, R.

    2010-01-01

    The paper presents the status of laser sensors based on direct and coherent detection technology. Potential and limitations of 3D- laser radar, laser vibrometer, and gated viewing systems will be described.

  18. Sensor Alignment by Tracks

    CERN Document Server

    Karimäki, V; Lampen, T; Lindén, T

    2003-01-01

    Good geometrical calibration is essential in the use of high resolution detectors. The individual sensors in the detector have to be calibrated with an accuracy better than the intrinsic resolution, which typically is of the order of 10 um. We present an effective method to perform fine calibration of sensor positions in a detector assembly consisting of a large number of pixel and strip sensors. Up to six geometric parameters, three for location and three for orientation, can be computed for each sensor on a basis of particle trajectories traversing the detector system. The performance of the method is demonstrated with both simulated tracks and tracks reconstructed from experimental data. We also present a brief review of other alignment methods reported in the literature.

  19. Dynamic Sensor Networks

    Directory of Open Access Journals (Sweden)

    Simone Gabriele

    2007-07-01

    Full Text Available The present paper discusses the possibility of using dynamic sensor networks for measurements over large areas. The main idea is to replace static networks, where the allocation of the sensors is pre defined, no matter how, and then the configuration is assumed and maintained, with a dynamic network whose configuration continuously changes in order to cover the whole measure area getting the different measures of the same point within a prefixed time interval. The main advantages are the reduced number of sensors required, a faster recover from damages, the possibility of changing dynamically the area or the subareas of interest, etc. The feasibility of such solution is shown by finding, in an optimal control problem formulation context, the trajectories of each sensor and the controls for such a motion. Simulation results are reported to highlight such results.

  20. EDL Sensor Suite Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Optical Air Data Systems (OADS) L.L.C. proposes a LIDAR based remote measurement sensor suite capable of satisfying a significant number of the desired sensing...

  1. Optical Sensors in Medicine

    Science.gov (United States)

    Baldini, Francesco

    Recent years have witnessed remarkable interest in the study of optical sensors applied in medicine, mainly for the detection of chemical and biochemical parameters. Health-care is surely the application field which seems to have the best future development perspectives for optical sensors, not only considering invasive applications (the high degree of miniaturization of optical fiber sensors, their considerable geometrical versatility, and extreme handiness make it possible to perform a continuous monitoring of numerous parameters, thus enabling performances which are often unique) but also taking into account the developments of optical multiarray biochips for the analysis of multiple parameters. The role of optical sensors in the European Integrated projects CLINICIP - Closed Loop Insulin Infusion in Critically Ill Patients - and CAREMAN - HealthCARE by Biosensor Measurements And Networking - is also described.

  2. Medical Sensor Network Infrastructures

    DEFF Research Database (Denmark)

    Andersen, Jacob

    is required, such as taking a blood sample, mailing it to a lab, where it is analysed and the result returned by mail. Due to the continuing size and cost reduction of electronic equipment, future medical sensors will be much smaller, cheaper and often disposable. Furthermore, integration of these sensors...... with the electronic health record (EHR) IT-systems will save a lot of work (and human errors), as the sensor readings will be directly recorded in the patient’s records by the sensors themselves, rather than by a transcription performed by a busy clinician. Although this development has been going on for at least...... a short while. This tension between simple use and security in a low-power clinical environment is the main theme of this dissertation. Un-secure medical equipment will never pass official certification by national health authorities, but on the other hand, experience shows that if using the equipment...

  3. Water Properties Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this Phase I project, Kaitech proposes to design a Water Properties Sensor (WPS) sensing system to synchronously measure the spectral inherent and apparent...

  4. Transient Microcavity Sensor

    CERN Document Server

    Shu, Fang-Jie; Özdemir, Şahin Kaya; Yang, Lan; Guo, Guang-Can

    2015-01-01

    A transient and high sensitivity sensor based on high-Q microcavity is proposed and studied theoretically. There are two ways to realize the transient sensor: monitor the spectrum by fast scanning of probe laser frequency or monitor the transmitted light with fixed laser frequency. For both methods, the non-equilibrium response not only tells the ultrafast environment variance, but also enable higher sensitivity. As examples of application, the transient sensor for nanoparticles adhering and passing by the microcavity is studied. It's demonstrated that the transient sensor can sense coupling region, external linear variation together with the speed and the size of a nanoparticle. We believe that our researches will open a door to the fast dynamic sensing by microcavity.

  5. Modular sensor network node

    Science.gov (United States)

    Davis, Jesse Harper Zehring [Berkeley, CA; Stark, Jr., Douglas Paul; Kershaw, Christopher Patrick [Hayward, CA; Kyker, Ronald Dean [Livermore, CA

    2008-06-10

    A distributed wireless sensor network node is disclosed. The wireless sensor network node includes a plurality of sensor modules coupled to a system bus and configured to sense a parameter. The parameter may be an object, an event or any other parameter. The node collects data representative of the parameter. The node also includes a communication module coupled to the system bus and configured to allow the node to communicate with other nodes. The node also includes a processing module coupled to the system bus and adapted to receive the data from the sensor module and operable to analyze the data. The node also includes a power module connected to the system bus and operable to generate a regulated voltage.

  6. Thermal microphotonic sensor and sensor array

    Science.gov (United States)

    Watts, Michael R [Albuquerque, NM; Shaw, Michael J [Tijeras, NM; Nielson, Gregory N [Albuquerque, NM; Lentine, Anthony L [Albuquerque, NM

    2010-02-23

    A thermal microphotonic sensor is disclosed for detecting infrared radiation using heat generated by the infrared radiation to shift the resonant frequency of an optical resonator (e.g. a ring resonator) to which the heat is coupled. The shift in the resonant frequency can be determined from light in an optical waveguide which is evanescently coupled to the optical resonator. An infrared absorber can be provided on the optical waveguide either as a coating or as a plate to aid in absorption of the infrared radiation. In some cases, a vertical resonant cavity can be formed about the infrared absorber to further increase the absorption of the infrared radiation. The sensor can be formed as a single device, or as an array for imaging the infrared radiation.

  7. Organic magnetic field sensor

    Science.gov (United States)

    McCamey, Dane; Boehme, Christoph

    2017-01-24

    An organic, spin-dependent magnetic field sensor (10) includes an active stack (12) having an organic material with a spin-dependence. The sensor (10) also includes a back electrical contact (14) electrically coupled to a back of the active stack (12) and a front electrical contact (16) electrically coupled to a front of the active stack (12). A magnetic field generator (18) is oriented so as to provide an oscillating magnetic field which penetrates the active stack (12).

  8. Thermal Anemometry Grid Sensor

    OpenAIRE

    Martin Arlit; Eckhard Schleicher; Uwe Hampel

    2017-01-01

    A novel thermal anemometry grid sensor was developed for the simultaneous measurement of cross-sectional temperature and axial velocity distribution in a fluid flow. The sensor consists of a set of platinum resistors arranged in a regular grid. Each platinum resistor allows the simultaneous measurement of fluid temperature via electrical resistance and flow velocity via constant voltage thermal anemometry. Cross-sectional measurement was enabled by applying a special multiplexing-excitation s...

  9. Fast Air Temperature Sensors

    DEFF Research Database (Denmark)

    Hendricks, Elbert

    1998-01-01

    The note documents briefly work done on a newly developed sensor for making fast temperature measurements on the air flow in the intake ports of an SI engine and in the EGR input line. The work reviewed has been carried out in close cooperation with Civ. Ing. Michael Føns, the author (IAU......) and Spencer C. Sorenson (ET). The theory which decribes in detail the overall dynamic chracteristics of the sensor was developed at IAU, DTU....

  10. Smart Sensors for Launch Vehicles

    Science.gov (United States)

    Ray, Sabooj; Mathews, Sheeja; Abraham, Sheena; Pradeep, N.; Vinod, P.

    2017-10-01

    Smart Sensors bring a paradigm shift in the data acquisition mechanism adopted for launch vehicle telemetry system. The sensors integrate signal conditioners, digitizers and communication systems to give digital output from the measurement location. Multiple sensors communicate with a centralized node over a common digital data bus. An in-built microcontroller gives the sensor embedded intelligence to carry out corrective action for sensor inaccuracies. A smart pressure sensor has been realized and flight-proven to increase the reliability as well as simplicity in integration so as to obtain improved data output. Miniaturization is achieved by innovative packaging. This work discusses the construction, working and flight performance of such a sensor.

  11. Smart Sensors for Launch Vehicles

    Science.gov (United States)

    Ray, Sabooj; Mathews, Sheeja; Abraham, Sheena; Pradeep, N.; Vinod, P.

    2017-12-01

    Smart Sensors bring a paradigm shift in the data acquisition mechanism adopted for launch vehicle telemetry system. The sensors integrate signal conditioners, digitizers and communication systems to give digital output from the measurement location. Multiple sensors communicate with a centralized node over a common digital data bus. An in-built microcontroller gives the sensor embedded intelligence to carry out corrective action for sensor inaccuracies. A smart pressure sensor has been realized and flight-proven to increase the reliability as well as simplicity in integration so as to obtain improved data output. Miniaturization is achieved by innovative packaging. This work discusses the construction, working and flight performance of such a sensor.

  12. Distributed sensor networks

    Science.gov (United States)

    Lacoss, R. T.

    1985-09-01

    The Distributed Sensor Networks (DSN) program is aimed at developing and extending target surveillance and tracking technology in systems that employ multiple spatially distributed sensors and processing resources. Such a system would be made up of sensors, data bases, and processors distributed throughout an area and interconnected by an appropriate digital data communication system. The detection, tracking, and classification of low flying aircraft has been selected to develop and evaluate DSN concepts in the light of a specific system problem. A DSN test bed has been developed and is being used to test and demonstrate DSN techniques and technology. The overall concept calls for a mix of sensor types. The initial test-bed sensors are small arrays of microphones at each node augmented by TV sensors at some nodes. This Semiannual Technical Summary (SATS) reports results for the period 1 October 1984 through 31 March 1985. Progress in the development of distributed tracking algorithms and their implementation in the DSN test-bed system is reviewed in Section II. Test-bed versions of distributed acoustic tracking algorithms now have been implemented and tested using simulated acoustic data. This required developing a solution to a basic distributed tracking problem: the information feedback problem. Target tracks received by one node from another node often implicitly include information that originally was obtained from the receiving node.

  13. INNOVATIVE HEAT FLUX SENSOR

    Directory of Open Access Journals (Sweden)

    G. N. Lukyanov

    2017-02-01

    Full Text Available Subject of Study.We present a method for heat flux measuring with the use of polarization properties of ferroelectric ceramics. Heat flux innovative sensor is developed on the basis of the proposed method. Its experimental verification is carried out. Method. The measurements are based on maintaining a balance between the processes caused by thermal energy and the energy of the electric field in the ferroelectric ceramics. Main Results. The testing of the proposed heat flux sensor has been organized in two stages. At the first stage the primary calibration has been performed by calibrated sensors ITP MG4.03/x(y “Potok”. At the second stage the testing of heat flux sensor has been carried out for calculating the quantity of heat. The comparison of the results to the readings of serial heat meters VKT-7 and STK-15 has been performed. Experiments have shown that the polarization properties of the ferroelectric ceramics can be used to measure the heat flow. Practical Relevance. The proposed sensor can be recommended as an apartment-level heat meter. The calibration of the proposed heat flux sensor with more accurate measurement tools gives the possibility to include it on the State Register of Measuring Instruments.

  14. La realidad como materia novelable: Alejo Carpentier

    Directory of Open Access Journals (Sweden)

    Raquel Arias Careaga

    2007-12-01

    Full Text Available Desde que en 1897 Benito Pérez Galdós defendiera como materia prima legítima de la literatura «la vida misma, de donde el artista saca las ficciones que nos instruyen y embelesan» (Pérez Galdós, 1990: 159, el realismo como instrumento de indagación y análisis de la sociedad no ha dejado de crecer y expandirse. Realismo crítico, como este de Galdós, que implica una ampliación del concepto chato de «realidad», incluyendo en ella «recuerdos, sueños, imaginación, locura, símbolos» para contribuir a la formación de un «realismo total» (Rodríguez Puértolas, 2000, II: 93, al que se une también la asimilación de enseñanzas esenciales como la que representa la narrativa de Cervantes: La novelística de Galdós hunde sus raíces en el mejor Cervantes, como puede verse en su peculiar sentido del humor y de la ironía, en la concepción perspectivista de la realidad y en tantas otras cosas, algunas de ellas en verdad fundamentales. Así el concepto de la Naturaleza y sus relaciones dialécticas con el ser humano; así el Amor como elemento vital y animador del orden cósmico, muy alejado del idealismo vulgar romántico (Ibid., 93.

  15. La fatiga como estado motivacional subjetivo

    OpenAIRE

    Cárdenas, D.; J. Conde-González; Perales, J C

    2017-01-01

    Actualmente no existe consenso sobre los factores que determinan la aparición de la fatiga. Hay factores que se derivan exclusivamente del esfuerzo físico, otros que dependen del esfuerzo mental que este lleva aparejado, y otros de los resultados de la tarea que se está realizando. Como consecuencia, se han desarrollado diferentes modelos explicativos que pretenden aunar las diferentes razones de su aparición. No obstante, la tendencia actual es entender la fatiga como un estado motivacion...

  16. Como si fuera posible recoger sentimientos

    OpenAIRE

    Vayreda Puigvert, Marian; Vallès Villanueva, Joan

    2011-01-01

    Se trata de una propuesta como resultado del trabajo conjunto entre la escuela de Arte Pigment y el ESPAI ZERO1 del Museu Comarcal de la Garrotxa, destinado exclusivamente a exposiciones temporales de creación contemporánea y como continuidad de propuestas anteriores de colaboración: REPLICA23 y SONESNAT JUNIOR. Com si fos possible recollir el sofriment es un proyecto de la artista Anna Manel.la, y se consideró una propuesta interesante y un reto para conversar, intercambiar y crear con los a...

  17. La norma penal como norma de conducta

    OpenAIRE

    Regis Prado, Luiz

    2011-01-01

    El artículo trata de la dicotomía entre norma de determinación y norma de valoración, para concluir que la norma penal es una norma jurídica de conducta, que prescribe un modo determinado de actuar. De esta forma, señala su estructura lógica y principales características, así como sus efectos en el campo de la antijuridicidad. SUMARIO: 1. Consideraciones generales; 2. Norma penal como norma de conducta. Norma de determinación o norma de valoración: distinción conceptual; 3. Nor...

  18. Los bienes culturales como patrimonio educativo

    OpenAIRE

    Panciroli, Chiara

    2016-01-01

    Resumen: El patrimonio y los lugares que lo acogen, conservan, y exponen (entendiendo el museo como una referencia particular), se convierten progresivamente en espacios que revisten un papel estratégico, sobre todo en términos formativos. Se trata de una función formativa que se ha construido y se sigue definiendo con la historia de los museos y la individuación de los diferentes sentidos del bien objeto. El museo, considerado como el escenario final para la transmisión y comunicación del co...

  19. A Imagem como Ruína

    Directory of Open Access Journals (Sweden)

    Míriam Volpe

    2001-12-01

    Full Text Available O dialogismo ente o filme Citizen Kane, de Orson Welles, e o poema “Kubla Khan”, de S.T. Coleridgé, é analisado, sendo evidenciados não só o tema em comum – o mito do Paraíso perdido – como também a similariedade na organização do disurso na justaposição das images, como fragmentos da memória a serem preservados.

  20. Sensors for quality control in welding Sensores para controle da qualidade em soldagem

    Directory of Open Access Journals (Sweden)

    Sadek Crisóstomo Absi Alfaro

    2012-09-01

    Full Text Available The classical inspection methods used for detecting and finding disturbances in welding process are based on direct measurement of its parameters as arc voltage, welding current, wire feed speed, etc. Using these inspection methods implies sensors insertion around the welding process and its presence could alter the metallic transference behavior and consequently an uneven quality as well as it can increase the production cost. For reducing these implications is necessary using a non intrusive inspection method. In this paper we will show nonintrusive methods to the weld quality inspection. These methods are based on sensor fusion, the extraction of global information coming from the interrelation data given by each sensor that, for example, sensing the spectroscopy radiation emission, the acoustic sensing of the electrical arc, the infrared emissions indicating the heat content of the weld. Finally, the fusion data will be applied to a statistical control for detecting and finding welding disturbances. The results will show that sensor fusion could be used as a tool to measure indirectly the weld quality in the GMAW process.Os métodos clássicos de inspeção utilizados para detectar e encontrar perturbações nos processos de soldagem são baseados comumente na medição direta de seus parâmetros como da tensão do arco, corrente de soldagem, velocidade de alimentação, etc. Usando esses métodos de inspeção implica inserção dos sensores em todo o processo de soldagem e sua presença poderia alterar o comportamento, por exemplo, da transferência metálica e, consequentemente, uma qualidade irregular da junta soldada, bem como provocaria o aumento do custo de produção. Para reduzir essas implicações é necessário usar um método de inspeção não intrusiva. Neste artigo mostrar-se métodos não intrusivos para a inspeção de qualidade de solda. Estes métodos baseiam-se na fusão de sensores, a extração da informação global

  1. Biodegradable Piezoelectric Force Sensor.

    Science.gov (United States)

    Curry, Eli J; Ke, Kai; Chorsi, Meysam T; Wrobel, Kinga S; Miller, Albert N; Patel, Avi; Kim, Insoo; Feng, Jianlin; Yue, Lixia; Wu, Qian; Kuo, Chia-Ling; Lo, Kevin W-H; Laurencin, Cato T; Ilies, Horea; Purohit, Prashant K; Nguyen, Thanh D

    2018-01-30

    Measuring vital physiological pressures is important for monitoring health status, preventing the buildup of dangerous internal forces in impaired organs, and enabling novel approaches of using mechanical stimulation for tissue regeneration. Pressure sensors are often required to be implanted and directly integrated with native soft biological systems. Therefore, the devices should be flexible and at the same time biodegradable to avoid invasive removal surgery that can damage directly interfaced tissues. Despite recent achievements in degradable electronic devices, there is still a tremendous need to develop a force sensor which only relies on safe medical materials and requires no complex fabrication process to provide accurate information on important biophysiological forces. Here, we present a strategy for material processing, electromechanical analysis, device fabrication, and assessment of a piezoelectric Poly-l-lactide (PLLA) polymer to create a biodegradable, biocompatible piezoelectric force sensor, which only employs medical materials used commonly in Food and Drug Administration-approved implants, for the monitoring of biological forces. We show the sensor can precisely measure pressures in a wide range of 0-18 kPa and sustain a reliable performance for a period of 4 d in an aqueous environment. We also demonstrate this PLLA piezoelectric sensor can be implanted inside the abdominal cavity of a mouse to monitor the pressure of diaphragmatic contraction. This piezoelectric sensor offers an appealing alternative to present biodegradable electronic devices for the monitoring of intraorgan pressures. The sensor can be integrated with tissues and organs, forming self-sensing bionic systems to enable many exciting applications in regenerative medicine, drug delivery, and medical devices.

  2. Engineering workstation: Sensor modeling

    Science.gov (United States)

    Pavel, M; Sweet, B.

    1993-01-01

    The purpose of the engineering workstation is to provide an environment for rapid prototyping and evaluation of fusion and image processing algorithms. Ideally, the algorithms are designed to optimize the extraction of information that is useful to a pilot for all phases of flight operations. Successful design of effective fusion algorithms depends on the ability to characterize both the information available from the sensors and the information useful to a pilot. The workstation is comprised of subsystems for simulation of sensor-generated images, image processing, image enhancement, and fusion algorithms. As such, the workstation can be used to implement and evaluate both short-term solutions and long-term solutions. The short-term solutions are being developed to enhance a pilot's situational awareness by providing information in addition to his direct vision. The long term solutions are aimed at the development of complete synthetic vision systems. One of the important functions of the engineering workstation is to simulate the images that would be generated by the sensors. The simulation system is designed to use the graphics modeling and rendering capabilities of various workstations manufactured by Silicon Graphics Inc. The workstation simulates various aspects of the sensor-generated images arising from phenomenology of the sensors. In addition, the workstation can be used to simulate a variety of impairments due to mechanical limitations of the sensor placement and due to the motion of the airplane. Although the simulation is currently not performed in real-time, sequences of individual frames can be processed, stored, and recorded in a video format. In that way, it is possible to examine the appearance of different dynamic sensor-generated and fused images.

  3. Condicionamiento clasico electrodermico aversivo y apetitivo utilizando imagenes como estimulos

    National Research Council Canada - National Science Library

    Redondo, Jaime; Mendez, Amavia

    2011-01-01

    El principal objetivo de este estudio consistio en comprobar si era posible obtener condicionamiento clasico electrodermico, tanto aversivo como apetitivo, utilizando imagenes como estimulos condicionados (ECs...

  4. El lenguaje como fundamento del derecho

    OpenAIRE

    Schweizer, Rainer J.

    2012-01-01

    En este artículo se rebate la concepción tradicional de la cultura jurídica según la cual el lenguaje es un simple instrumento de los juristas. Muestra como el Estado de Derecho y la democracia, fundan su legitimidad en el lenguaje, lo cual exige considerarlo en su significado más profundo.

  5. La biblioteca como editora de contenidos

    Directory of Open Access Journals (Sweden)

    Alonso-Arévalo, Julio

    2015-12-01

    Full Text Available Una de las características más innovadoras de la biblioteca del siglo 21 tiene que ver con la toma de una postura activa frente a la gestión y generación de contenidos. Con la llegada de la Web 2.0 las bibliotecas no sólo siguen salvaguardando y difundiendo información como han venido realizando a lo largo de su historia, también cada vez con más frecuencia crean nueva información con el objetivo de prestar los mejores servicios a sus ciudadanos, a través de recursos y servicios tales como la elaboración guías de investigación, boletines de alerta y novedades, recursos web, información a través de sus blogs, y como administradores de contenidos a través de repositorios y revistas de acceso abierto. Un paso más allá en esta dinámica tienen que ver con la biblioteca como editora y distribuidora de libros, especialmente en el ámbito local, siendo la impulsora, formadora, dinamizador y difusoras de las obras de los autores de su comunidad.

  6. APOSENTADORIA: como professores vivenciam este momento?

    Directory of Open Access Journals (Sweden)

    Cristiane Nervis Conrado Machado

    2017-05-01

    Full Text Available O presente artigo buscou compreender as implicações que a aposentadoria causa na vida de professores, levando em conta o significado que a aposentadoria representa à estes, considerando os pontos de maior mudança após a aposentadoria, bem como os aspectos positivos e negativos causados pela aposentadoria na percepção dos sujeitos da pesquisa. Para tanto, foi realizada uma pesquisa qualitativa caracterizada como exploratória e descritiva com professores aposentados por mais de dois anos, com idade entre 58 e 66 anos, através de entrevistas individuais, com roteiros semiestruturados. A análise dos dados foi por meio da análise de conteúdo de Bardin (2011. Entre os principais resultados, destaca-se o significado de “liberdade” que a aposentadoria representa, a rotina como maior mudança e flexibilidade de horários dentre os pontos positivos e a falta dos alunos como aspecto negativo, contudo, pode-se perceber que a aposentadoria possibilitou e contribuiu para que os professores pudessem desfrutar de momentos de lazer, dedicando cuidado à família e realizando seus anseios e vontades.

  7. EL PERIODISMO CIVICO COMO COMUNICACION POLITICA

    Directory of Open Access Journals (Sweden)

    Ana María Miralles C.

    1998-01-01

    Full Text Available La autora retoma el ejercicio del periodismo cívico como el espacio en el cual la formación de la opinión pública adquiere características de un proyecto político dinámico en el que el ciudadano es el ente fundamental.

  8. Como una luna en el agua [Score

    Directory of Open Access Journals (Sweden)

    Francisco del Pino

    2014-12-01

    Full Text Available The title of the solo piano piece Como una luna en el agua, composed between June and July of 2014, refers to the end of the seventh chapter of the novel Rayuela (Hopscotch by the Argentine writer Julio Cortázar, in which an allegorical description of a kiss takes the form of a prose poem.

  9. Underwater Sensor Nodes and Networks

    Directory of Open Access Journals (Sweden)

    Jaime Lloret

    2013-09-01

    Full Text Available Sensor technology has matured enough to be used in any type of environment. The appearance of new physical sensors has increased the range of environmental parameters for gathering data. Because of the huge amount of unexploited resources in the ocean environment, there is a need of new research in the field of sensors and sensor networks. This special issue is focused on collecting recent advances on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments. On the one hand, from the sensor node perspective, we will see works related with the deployment of physical sensors, development of sensor nodes and transceivers for sensor nodes, sensor measurement analysis and several issues such as layer 1 and 2 protocols for underwater communication and sensor localization and positioning systems. On the other hand, from the sensor network perspective, we will see several architectures and protocols for underwater environments and analysis concerning sensor network measurements. Both sides will provide us a complete view of last scientific advances in this research field.

  10. Underwater sensor nodes and networks.

    Science.gov (United States)

    Lloret, Jaime

    2013-09-05

    Sensor technology has matured enough to be used in any type of environment. The appearance of new physical sensors has increased the range of environmental parameters for gathering data. Because of the huge amount of unexploited resources in the ocean environment, there is a need of new research in the field of sensors and sensor networks. This special issue is focused on collecting recent advances on underwater sensors and underwater sensor networks in order to measure, monitor, surveillance of and control of underwater environments. On the one hand, from the sensor node perspective, we will see works related with the deployment of physical sensors, development of sensor nodes and transceivers for sensor nodes, sensor measurement analysis and several issues such as layer 1 and 2 protocols for underwater communication and sensor localization and positioning systems. On the other hand, from the sensor network perspective, we will see several architectures and protocols for underwater environments and analysis concerning sensor network measurements. Both sides will provide us a complete view of last scientific advances in this research field.

  11. Micromachined Fluid Inertial Sensors

    Directory of Open Access Journals (Sweden)

    Shiqiang Liu

    2017-02-01

    Full Text Available Micromachined fluid inertial sensors are an important class of inertial sensors, which mainly includes thermal accelerometers and fluid gyroscopes, which have now been developed since the end of the last century for about 20 years. Compared with conventional silicon or quartz inertial sensors, the fluid inertial sensors use a fluid instead of a solid proof mass as the moving and sensitive element, and thus offer advantages of simple structures, low cost, high shock resistance, and large measurement ranges while the sensitivity and bandwidth are not competitive. Many studies and various designs have been reported in the past two decades. This review firstly introduces the working principles of fluid inertial sensors, followed by the relevant research developments. The micromachined thermal accelerometers based on thermal convection have developed maturely and become commercialized. However, the micromachined fluid gyroscopes, which are based on jet flow or thermal flow, are less mature. The key issues and technologies of the thermal accelerometers, mainly including bandwidth, temperature compensation, monolithic integration of tri-axis accelerometers and strategies for high production yields are also summarized and discussed. For the micromachined fluid gyroscopes, improving integration and sensitivity, reducing thermal errors and cross coupling errors are the issues of most concern.

  12. Whispering gallery mode sensors.

    Science.gov (United States)

    Foreman, Matthew R; Swaim, Jon D; Vollmer, Frank

    2015-06-30

    We present a comprehensive overview of sensor technology exploiting optical whispering gallery mode (WGM) resonances. After a short introduction we begin by detailing the fundamental principles and theory of WGMs in optical microcavities and the transduction mechanisms frequently employed for sensing purposes. Key recent theoretical contributions to the modeling and analysis of WGM systems are highlighted. Subsequently we review the state of the art of WGM sensors by outlining efforts made to date to improve current detection limits. Proposals in this vein are numerous and range, for example, from plasmonic enhancements and active cavities to hybrid optomechanical sensors, which are already working in the shot noise limited regime. In parallel to furthering WGM sensitivity, efforts to improve the time resolution are beginning to emerge. We therefore summarize the techniques being pursued in this vein. Ultimately WGM sensors aim for real-world applications, such as measurements of force and temperature, or alternatively gas and biosensing. Each such application is thus reviewed in turn, and important achievements are discussed. Finally, we adopt a more forward-looking perspective and discuss the outlook of WGM sensors within both a physical and biological context and consider how they may yet push the detection envelope further.

  13. Sensor Characteristics Reference Guide

    Energy Technology Data Exchange (ETDEWEB)

    Cree, Johnathan V.; Dansu, A.; Fuhr, P.; Lanzisera, Steven M.; McIntyre, T.; Muehleisen, Ralph T.; Starke, M.; Banerjee, Pranab; Kuruganti, T.; Castello, C.

    2013-04-01

    The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information

  14. Micromachined Fluid Inertial Sensors

    Science.gov (United States)

    Liu, Shiqiang; Zhu, Rong

    2017-01-01

    Micromachined fluid inertial sensors are an important class of inertial sensors, which mainly includes thermal accelerometers and fluid gyroscopes, which have now been developed since the end of the last century for about 20 years. Compared with conventional silicon or quartz inertial sensors, the fluid inertial sensors use a fluid instead of a solid proof mass as the moving and sensitive element, and thus offer advantages of simple structures, low cost, high shock resistance, and large measurement ranges while the sensitivity and bandwidth are not competitive. Many studies and various designs have been reported in the past two decades. This review firstly introduces the working principles of fluid inertial sensors, followed by the relevant research developments. The micromachined thermal accelerometers based on thermal convection have developed maturely and become commercialized. However, the micromachined fluid gyroscopes, which are based on jet flow or thermal flow, are less mature. The key issues and technologies of the thermal accelerometers, mainly including bandwidth, temperature compensation, monolithic integration of tri-axis accelerometers and strategies for high production yields are also summarized and discussed. For the micromachined fluid gyroscopes, improving integration and sensitivity, reducing thermal errors and cross coupling errors are the issues of most concern. PMID:28216569

  15. Sensor array signal processing

    CERN Document Server

    Naidu, Prabhakar S

    2009-01-01

    Chapter One: An Overview of Wavefields 1.1 Types of Wavefields and the Governing Equations 1.2 Wavefield in open space 1.3 Wavefield in bounded space 1.4 Stochastic wavefield 1.5 Multipath propagation 1.6 Propagation through random medium 1.7 ExercisesChapter Two: Sensor Array Systems 2.1 Uniform linear array (ULA) 2.2 Planar array 2.3 Distributed sensor array 2.4 Broadband sensor array 2.5 Source and sensor arrays 2.6 Multi-component sensor array2.7 ExercisesChapter Three: Frequency Wavenumber Processing 3.1 Digital filters in the w-k domain 3.2 Mapping of 1D into 2D filters 3.3 Multichannel Wiener filters 3.4 Wiener filters for ULA and UCA 3.5 Predictive noise cancellation 3.6 Exercises Chapter Four: Source Localization: Frequency Wavenumber Spectrum4.1 Frequency wavenumber spectrum 4.2 Beamformation 4.3 Capon's w-k spectrum 4.4 Maximum entropy w-k spectrum 4.5 Doppler-Azimuth Processing4.6 ExercisesChapter Five: Source Localization: Subspace Methods 5.1 Subspace methods (Narrowband) 5.2 Subspace methods (B...

  16. Sensor technologies: healthcare, wellness, and environmental applications

    National Research Council Canada - National Science Library

    McGrath, Michael J., Ph.D; Ní Scanaill, Cliodhna

    Sensor Technologies: Healthcare, Wellness and Environmental Applications explores the key aspects of sensor technologies, covering wired, wireless, and discrete sensors for the specific application domains of healthcare...

  17. Capacitive proximity sensor

    Science.gov (United States)

    Kronberg, James W.

    1994-01-01

    A proximity sensor based on a closed field circuit. The circuit comprises a ring oscillator using a symmetrical array of plates that creates an oscillating displacement current. The displacement current varies as a function of the proximity of objects to the plate array. Preferably the plates are in the form of a group of three pair of symmetric plates having a common center, arranged in a hexagonal pattern with opposing plates linked as a pair. The sensor produces logic level pulses suitable for interfacing with a computer or process controller. The proximity sensor can be incorporated into a load cell, a differential pressure gauge, or a device for measuring the consistency of a characteristic of a material where a variation in the consistency causes the dielectric constant of the material to change.

  18. Modular chemiresistive sensor

    Energy Technology Data Exchange (ETDEWEB)

    Alam, Maksudul M.; Sampathkumaran, Uma

    2018-02-20

    The present invention relates to a modular chemiresistive sensor. In particular, a modular chemiresistive sensor for hypergolic fuel and oxidizer leak detection, carbon dioxide monitoring and detection of disease biomarkers. The sensor preferably has two gold or platinum electrodes mounted on a silicon substrate where the electrodes are connected to a power source and are separated by a gap of 0.5 to 4.0 .mu.M. A polymer nanowire or carbon nanotube spans the gap between the electrodes and connects the electrodes electrically. The electrodes are further connected to a circuit board having a processor and data storage, where the processor can measure current and voltage values between the electrodes and compare the current and voltage values with current and voltage values stored in the data storage and assigned to particular concentrations of a pre-determined substance such as those listed above or a variety of other substances.

  19. Laser Scanner Como Sistema de Detección de Entornos Viales

    Directory of Open Access Journals (Sweden)

    F. García

    2011-01-01

    Full Text Available Resumen: Los últimos avances en seguridad vial, con sistemas cada vez más complejos, requieren de los más modernos sistemas de adquisición de información. La naturaleza misma del problema requiere sensores capaces de proveer información fiable para tareas complejas y exigentes. Los escáneres láser (LIDAR han demostrado ser una familia de sensores altamente fiable, por lo que durante los últimos años los esfuerzos dedicados a investigar posibles aplicaciones viales han ido en aumento. De esta forma, es cada vez más frecuente observar sistemas de ayuda a la conducción (ADAS con este tipo de dispositivos que proveen de información del entorno necesaria para realizar tareas complejas como deteccián y prediccián de situaciones peligrosas. En el presente trabajo, dos sistemas LIDAR han sido probados para comprobar sus capacidades reales en entornos viales. En segundo término, se propone una aplicación que hace uso de las capacidades de dichos sensores para la detección y clasificación de obstaculos en entornos viarios. Palabras clave: sensores, procesamiento de senales, sistemas reales, vehiculos, algoritmos de deteccion

  20. Mechanoluminescent Contact Type Sensor

    Directory of Open Access Journals (Sweden)

    A. K. Yefremov

    2017-01-01

    Full Text Available Mechanoluminescent sensing elements convert mechanical stress into optical radiation. Advantages of such sensors are the ability to generate an optical signal, solid-state, simple structure, and resistance to electromagnetic interference. Mechanoluminescent sensor implementations can possess the concentrated and distributed sensitivity, thereby allowing us to detect the field of mechanical stresses distributed across the area and in volume. Most modern semiconductor photo-detectors can detect mechanoluminescent radiation, so there are no difficulties to provide its detection when designing the mechanoluminescent sensing devices. Mechanoluminescent substances have especial sensitivity to shock loads, and this effect can be used to create a fuse the structure of which includes a target contact type sensor with a photosensitive actuator. The paper briefly describes the theoretical basics of mechanoluminiscence: a light signal emerges from the interaction of crystalline phosphor luminescence centers with electrically charged dislocations, moving due to the deformation of the crystal. A mathematical model of the mechanoluminescent conversion is represented as a functional interaction between parameters of the mechanical shock excitation and the sensor light emission. Examples of computing the optical mechanoluminescent output signal depending on the duration and peak level of impulse load are given. It is shown that the luminous flux, generated by mechanoluminescent sensing element when there is an ammunition-target collision causes the current emerging in photo-detector (photodiode that is sufficient for a typical actuator of the fuse train to operate. The potential possibility to create a contact target type sensor based on the light-sensitive mechanoluminescent sensor was proved by the calculation and simulation results.

  1. Environmental exposure tracking sensor

    Science.gov (United States)

    Havens, Teresa; Everhart, Joel; McFerran, Jace

    2009-03-01

    Cornerstone Research Group Inc. (CRG) has developed environmental exposure tracking (EET) sensors using shape memory polymer (SMP) to monitor the degradation of perishable items, such as munitions, medicines or foods, by measuring the cumulative exposure to temperature and moisture. SMPs are polymers whose qualities have been altered to give them dynamic shape "memory" properties. Under thermal or moisture stimuli, SMP exhibits a radical change from a rigid thermoset to a highly flexible, elastic state. The dynamic response of the SMP can be tailored to match the degradation profile of the perishable item. SMP-based EET sensors require no digital memory or internal power supply and provide the capability of inexpensive, long-term life cycle monitoring thermal and moisture exposure over time. In a Phase I and II SBIR effort with the Navy, CRG demonstrated the feasibility of SMP-based EET sensor with two material systems. These material systems required different activation stimuli, heat or water vapor pressure. CRG developed the ability to tailor these materials to customize the dynamic response to match various degradation profiles of munitions. CRG optimized and characterized the SMP formulations and sensor design configuration to develop a suite of data from which any degradation profile can be met. CRG's EET sensors are capable of monitoring temperatures from -30 °C to 260 °C. The prototypes monitor cumulative thermal exposure and provide real-time information in a visually readable or a remotely interrogated version. CRG is currently scaling up the manufacture of the sensors for munitions reliability applications with the Navy.

  2. Wireless rechargeable sensor networks

    CERN Document Server

    Yang, Yuanyuan

    2015-01-01

    This SpringerBrief provides a concise guide to applying wireless energy transfer techniques in traditional battery-powered sensor networks. It examines the benefits and challenges of wireless power including efficiency and reliability. The authors build a wireless rechargeable sensor networks from scratch and aim to provide perpetual network operation. Chapters cover a wide range of topics from the collection of energy information and recharge scheduling to joint design with typical sensing applications such as data gathering. Problems are approached using a natural combination of probability

  3. Novel nanostructured oxygen sensor

    Science.gov (United States)

    Boardman, Alan James

    New government regulations and industry requirements for medical oxygen sensors require the development of alternate materials and process optimization of primary sensor components. Current oxygen sensors are not compliant with the Restriction of Hazardous Substances (RoHS) Directive. This work focused on two areas. First, was finding suitable readily available materials for the sensor anodes. Second was optimizing the processing of the sensor cathode membrane for reduced delamination. Oxygen sensors were made using tin (Sn) and bismuth (Bi) electrodes, potassium hydroxide (KOH) and acetic acid (CH3COOH) electrolytes with platinum (Pt) and gold (Au) reference electrodes. Bi electrodes were fabricated by casting and pressing processes. Electrochemical characterization of the Sn and Bi electrodes was performed by Cyclic Voltammetry (CV), Electrochemical Impedance Spectroscopy (EIS) and sensing characterization per BSEN ISO 21647:2009 at various oxygen percentages, 0%, 20.9% and 100% oxygen levels with an automated test apparatus. The Sn anode with both electrolyte solutions showed good oxygen sensing properties and performance in a sensor. This system shows promise for replacement of Pb electrodes as required by the RoHS Directive. The Bi anode with Au cathode in both KOH and CH3COOH electrolytes showed acceptable performance and oxygen sensing properties. The Bi anodes fabricated by separate manufacturing methods demonstrated effectiveness for use in medical oxygen sensors. Gold thin films were prepared by magnetron sputtering on Flouroethylene Polymer (FEP) films. The FEP substrate temperature ranged from -77°C to 50°C. X-Ray Diffraction (XRD) and 4-point resistivity characterized the effects of substrate temperature to Au thin film particle size. XRD peak broadening and resistivity measurements showed a strong correlation of particle size to FEP substrate temperature. Particle size at 50°C was 594A and the -77°C particle size was 2.4 x 103A. Substrate

  4. Magnetic nanocomposite sensor

    KAUST Repository

    Alfadhel, Ahmed

    2016-05-06

    A magnetic nanocomposite device is described herein for a wide range of sensing applications. The device utilizes the permanent magnetic behavior of the nanowires to allow operation without the application of an additional magnetic field to magnetize the nanowires, which simplifies miniaturization and integration into microsystems. In5 addition, the nanocomposite benefits from the high elasticity and easy patterning of the polymer-based material, leading to a corrosion-resistant, flexible material that can be used to realize extreme sensitivity. In combination with magnetic sensor elements patterned underneath the nanocomposite, the nanocomposite device realizes highly sensitive and power efficient flexible artificial cilia sensors for flow measurement or tactile sensing.

  5. Fluorescent temperature sensor

    Science.gov (United States)

    Baker, Gary A [Los Alamos, NM; Baker, Sheila N [Los Alamos, NM; McCleskey, T Mark [Los Alamos, NM

    2009-03-03

    The present invention is a fluorescent temperature sensor or optical thermometer. The sensor includes a solution of 1,3-bis(1-pyrenyl)propane within a 1-butyl-1-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide ionic liquid solvent. The 1,3-bis(1-pyrenyl)propane remains unassociated when in the ground state while in solution. When subjected to UV light, an excited state is produced that exists in equilibrium with an excimer. The position of the equilibrium between the two excited states is temperature dependent.

  6. Photoionization microplasma sensor

    Science.gov (United States)

    Mustafaev, A. S.; Rastvorova, I. V.; Podenko, S. S.; Tsyganov, A. B.

    2017-11-01

    New developments in the physics of plasma are presented, specifically, research of completely new method of atoms’ and molecules’ detection in gaseous phase – collisional electron spectroscopy. As a result, the microplasma sensor for quality and quantity analysis of the gaseous mixture was created. It works in the discharge afterglow mode using He as a buffer gas. In addition, the modification of the sensor using resonance photon photoionization was developed. This consideration gives the opportunity for wide practical appliance as an individual gas analyzer for industrial and medical purposes.

  7. Adaptive reconfigurable distributed sensor architecture

    Science.gov (United States)

    Akey, Mark L.

    1997-07-01

    The infancy of unattended ground based sensors is quickly coming to an end with the arrival of on-board GPS, networking, and multiple sensing capabilities. Unfortunately, their use is only first-order at best: GPS assists with sensor report registration; networks push sensor reports back to the warfighter and forwards control information to the sensors; multispectral sensing is a preset, pre-deployment consideration; and the scalability of large sensor networks is questionable. Current architectures provide little synergy among or within the sensors either before or after deployment, and do not map well to the tactical user's organizational structures and constraints. A new distributed sensor architecture is defined which moves well beyond single sensor, single task architectures. Advantages include: (1) automatic mapping of tactical direction to multiple sensors' tasks; (2) decentralized, distributed management of sensor resources and tasks; (3) software reconfiguration of deployed sensors; (4) network scalability and flexibility to meet the constraints of tactical deployments, and traditional combat organizations and hierarchies; and (5) adaptability to new battlefield communication paradigms such as BADD (Battlefield Analysis and Data Dissemination). The architecture is supported in two areas: a recursive, structural definition of resource configuration and management via loose associations; and a hybridization of intelligent software agents with tele- programming capabilities. The distributed sensor architecture is examined within the context of air-deployed ground sensors with acoustic, communication direction finding, and infra-red capabilities. Advantages and disadvantages of the architecture are examined. Consideration is given to extended sensor life (up to 6 months), post-deployment sensor reconfiguration, limited on- board sensor resources (processor and memory), and bandwidth. It is shown that technical tasking of the sensor suite can be automatically

  8. A Sensor web architecture for sharing oceanographic sensor data

    OpenAIRE

    Jirka, Simon; Toma, Daniel; Río Fernandez, Joaquín del; Delory, Eric

    2014-01-01

    This paper introduces the Sensor Web architecture of the NeXOS project as example how interoperable standards help, to facilitate the creation of an infrastructure for sharing oceanographic observation data and the integration of sensor data into applications. Important technological foundations of the NeXOS Sensor Web architecture are the concepts of spatial data infrastructures and the Sensor Web Enablement framework of the Open Geospatial Consortium. As a result an ...

  9. New Generation Sensor Web Enablement

    Directory of Open Access Journals (Sweden)

    Christoph Stasch

    2011-03-01

    Full Text Available Many sensor networks have been deployed to monitor Earth’s environment, and more will follow in the future. Environmental sensors have improved continuously by becoming smaller, cheaper, and more intelligent. Due to the large number of sensor manufacturers and differing accompanying protocols, integrating diverse sensors into observation systems is not straightforward. A coherent infrastructure is needed to treat sensors in an interoperable, platform-independent and uniform way. The concept of the Sensor Web reflects such a kind of infrastructure for sharing, finding, and accessing sensors and their data across different applications. It hides the heterogeneous sensor hardware and communication protocols from the applications built on top of it. The Sensor Web Enablement initiative of the Open Geospatial Consortium standardizes web service interfaces and data encodings which can be used as building blocks for a Sensor Web. This article illustrates and analyzes the recent developments of the new generation of the Sensor Web Enablement specification framework. Further, we relate the Sensor Web to other emerging concepts such as the Web of Things and point out challenges and resulting future work topics for research on Sensor Web Enablement.

  10. LA INVESTIGACION SOCIAL COMO POSICION DE SUBJETIVIDAD

    Directory of Open Access Journals (Sweden)

    Ernesto Hernández B.

    1995-01-01

    Full Text Available Este ensayo-comentario, resalta al poder y al deseo como fuerzas que al entrar en relación, hacen posible la resistencia entendida como el entre-dos, resistencia que produce subjetivación en la que la unidad del yo es rota, dejando entrever así el devenir o el sin-sentido. Al poner en evidencia la relación de fuerzas, el ensayo-comentario hace visibles ligazones de la investigación no solamente con los trabajos de Michel Foucault y Giles Deleuze, sino también con Gabriel Tarde y la micro-sociología, ligazones que pretenden romper con las concepciones tradicionales que han abordado el problema de la violencia, todas ellas causales o esencialistas, abriendo caminos alternos para pensar la subjetividad y con ella, la cultura.

  11. Aerospace Sensor Systems: From Sensor Development To Vehicle Application

    Science.gov (United States)

    Hunter, Gary W.

    2008-01-01

    This paper presents an overview of years of sensor system development and application for aerospace systems. The emphasis of this work is on developing advanced capabilities for measurement and control of aeropropulsion and crew vehicle systems as well as monitoring the safety of those systems. Specific areas of work include chemical species sensors, thin film thermocouples and strain gages, heat flux gages, fuel gages, SiC based electronic devices and sensors, space qualified electronics, and MicroElectroMechanical Systems (MEMS) as well as integrated and multifunctional sensor systems. Each sensor type has its own technical challenges related to integration and reliability in a given application. The general approach has been to develop base sensor technology using microfabrication techniques, integrate sensors with "smart" hardware and software, and demonstrate those systems in a range of aerospace applications. Descriptions of the sensor elements, their integration into sensors systems, and examples of sensor system applications will be discussed. Finally, suggestions related to the future of sensor technology will be given. It is concluded that smart micro/nano sensor technology can revolutionize aerospace applications, but significant challenges exist in maturing the technology and demonstrating its value in real-life applications.

  12. LAS COMUNICACIONES INTERPERSONALES COMO FACTOR DE APRENDIZAJE

    Directory of Open Access Journals (Sweden)

    Paco Cerezo Sánchez

    2010-01-01

    Full Text Available Durante la impartición de un curso en red aparecen múltiples comunicaciones, crecen como árboles que impiden ver el bosque, hasta que ese bosque de comunicaciones impide ver cada uno de los árboles. La formación en red funciona como un sistema complejo, donde las intervenciones de cada parte (alumno o docente influyen en todos los demás. Este documento aporta instrumentos que sirven al docente para ordenar ese bosque, para convertir ese bosque en un jardín a goce de todos, facilitando así los procesos de aprendizaje. El docente-formador, si actúa como facilitador de procesos, necesita comprender y manejar las comunicaciones y ese dominio es necesario tanto en el nivel semántico como en el nivel relacional de la comunicación. Este documento desarrolla las competencias de comunicación interpersonal del docente en su nivel relacional. Primero presenta un marco teórico para analizar las comunicaciones interpersonales que se dan en los grupos de aprendizaje en red, luego sugiere un gráfico en 2 coordenadas para situar dichas comunicaciones (y roles y propone un orden en la toma de decisiones sobre qué hacer con dichas comunicaciones. Los ejemplos aquí expuestos provienen de numerosos cursos de formación continua impartidos en red entre 2002 y 2008 a formadores y a técnicos adultos de la Unión Europea y de Latinoamérica.

  13. El rock como conformador de identidades juveniles

    OpenAIRE

    Adrián de Garay

    1996-01-01

    El autor analiza la relación entre el rock y las identidades juveniles, a partir del abordaje de cinco "estilos" que se pueden identificar como constitutivos de éstas identidades. Ellos son: la jerga, la estética, las producciones culturales, los no-lugares y el territorio. Finaliza el artículo señalando algunos hitos importantes de la cultura rockera en la ciudad de México.

  14. El rock como conformador de identidades juveniles

    Directory of Open Access Journals (Sweden)

    Adrián de Garay

    1996-04-01

    Full Text Available El autor analiza la relación entre el rock y las identidades juveniles, a partir del abordaje de cinco “estilos” que se pueden identificar como constitutivos de éstas identidades. Ellos son: la jerga, la estética, las producciones culturales, los no-lugares y el territorio. Finaliza el artículo señalando algunos hitos importantes de la culturarockera en la ciudad de México.

  15. El rock como conformador de identidades juveniles

    Directory of Open Access Journals (Sweden)

    Adrián de Garay

    1996-01-01

    Full Text Available El autor analiza la relación entre el rock y las identidades juveniles, a partir del abordaje de cinco "estilos" que se pueden identificar como constitutivos de éstas identidades. Ellos son: la jerga, la estética, las producciones culturales, los no-lugares y el territorio. Finaliza el artículo señalando algunos hitos importantes de la cultura rockera en la ciudad de México.

  16. La Realidad Aumentada como complemento motivacional

    Directory of Open Access Journals (Sweden)

    Gazcón, Nicolás Fernando

    2016-06-01

    Full Text Available El acelerado avance de la tecnología permite que las tecnologías emergentes sean accesibles por todos los usuarios. Ejemplos de estas tecnologías son la Realidad Aumentada y la Reconstrucción 3D, que gracias a dispositivos como tabletas o teléfonos inteligentes, pueden utilizarse de manera ubicua. Éstas tienen un enorme potencial en el campo de la educación, ya sea como recurso para entender conceptos complejos, como para motivar el aprendizaje de nuevos contenidos. El desafío de estas tecnologías es integrarlas para que sean accesibles y fáciles de utilizar por los docentes y los alumnos. En este trabajo presentamos una metodología para motivar el aprendizaje tanto en tareas de campo, mediante el uso de la Reconstrucción 3D, como en el ámbito escolar mediante libros aumentados. Por medio de un caso de estudio introducimos la Reconstrucción 3D de elementos fósiles de un sitio paleontológico bonaerense, para luego incorporar estos contenidos generados en un libro aumentado. A partir de la digitalización de huellas y fósiles de sitios paleontológicos, se obtuvieron modelos 3D que se integraron en un ambiente de aprendizaje inmersivo en el aula mediante los libros aumentados. Presentamos las opiniones de docentes de distintas disciplinas, que resaltan las posibilidades de esta metodología para su inclusión en el ámbito educacional regional.

  17. La escritura como dispositivo constituyente de sujeto

    Directory of Open Access Journals (Sweden)

    Francisco Antonio Arias Murillo

    2012-01-01

    Full Text Available Este artículo pretende demostrar el modo como la escritura se convierte en un “dispositivo transformador del hombre”, en la medida en que posibilita la creación de una nueva realidad. Esta es una actividad que le permite al hombre tomar distancia de su sí natural, trascender hasta saberse otro, repleto de alternativas, abierto y expuesto al cambio. Lo anterior le permite pensarse y tomar la existencia en sus manos, superar la dependencia y asumir su autonomía, como diría Foucault: “haciendo de su vida una obra de arte”. Además de lo anterior, el presente artículo expone cómo la escritura, particularmente académica, puede ser un referente válido e importante para visibilizar los modos como se constituye el sujeto, especialmente docente; o, por el contrario, cómo o de qué manera es constituido el sujeto docente por los discursos clásicos representacionales con los que se expresan y comunican las ciencias, las disciplinas y las profesiones actualmente.

  18. La reescritura como herramienta de respuesta literaria

    Directory of Open Access Journals (Sweden)

    Daniela Buksdorf

    2015-01-01

    Full Text Available En este artículo se presenta la reescritura como un ejercicio de respuesta y/o reivindicación, a partir del estudio y análisis de dos reescrituras - Una tempestad , de Aimé Césaire y Ancho mar de los Sargazos , de Jean Rhys- que tienen como hipotexto obras canónicas cuyo origen se encuentra en el Imperio Inglés. Césaire toma como texto de origen La tempestad de William Shakespeare, mientras que Rhys trabaja desde la novela victoriana Jane Eyre , de Charlotte Brontë. El objetivo de este artículo es identificar las respuestas a dichas obras canónicas, modificando el discurso presente en los escritos estudiados. Para esto, se revisarán los conceptos de canon y reescritura, se analizarán los textos reescritos desde su base canónica y se compararán ejes centrales de las novelas y tratamiento de personajes y contexto, para así detectar las cercanías y lejanías de las obras con los textos canónicos y poder identificar los discursos perseguidos por los autores de las reescrituras.

  19. EL CONFLICTO COMO CONSTRUCTOR DE CIUDAD

    Directory of Open Access Journals (Sweden)

    Twiggy Ortegón

    2012-04-01

    Full Text Available El planteamiento central de este articulo, es el de sugerir una análisis en torno a algunas de las condiciones o mecanismo necesarios para que el conflicto opere como un potenciador de la diferencia y creador de alternativas para la convivencia Se realiza una distinción del concepto, un análisis de contenidos interaccionales en dinámicas de conflicto y su relación con el contexto urbano de Bogotá, enfocándose en ámbitos escolares. En ciudades como Bogotá, las discusiones y acciones que diferentes estamentos han emprendido frente a la manera de concebir y gestionar el conflicto, desembocan en la creación de diferentes organismos como los centros de conciliación, la aplicación de fórmulas y técnicas para la solución de conflictos, el desarrollo de propuestas desde entes administrativos a nivel distrital y las nuevas disposiciones que plantea la Ley 115 sobre Gobierno Escolar y manuales de convivencia.

  20. OS MUSEUS COMO ESPAÇOS EDUCATIVOS

    Directory of Open Access Journals (Sweden)

    Maria da Graça J. Setton

    2017-09-01

    Full Text Available RESUMO: O objetivo deste artigo é fazer uma reflexão acerca dos espaços museológicos como prática educativa. Concebendo-os como um lazer diferenciado, tem-se uma falsa representação de que parte da população seria incapaz de usufruir de seus acervos. Partindo de uma perspectiva histórica acerca dos museus e da teoria de Pierre Bourdieu, procurou-se observar estruturas mentais que instauram barreiras culturais para algumas linguagens e práticas. Nesse sentido, como inspiração, visitaram-se alguns acervos no intuito de apreender as estratégias de aproximação e/ou afastamento de suas exposições. Para finalizar, problematizando o envolvimento com práticas de cultura responsáveis em grande parte pela formação de um capital cultural, provocou-se a reflexão sobre as diferentes formas de apreciar e de se sensibilizar com artefatos culturais diversos.

  1. LA VIOLENCIA COMO EFECTO DE SOCIALIZACION

    Directory of Open Access Journals (Sweden)

    Gisela Daza Navarrete

    1995-01-01

    Full Text Available El espacio teórico abierto por Winnicott con el concepto de Espacio Potencial es un terreno fecundo para pensar la socialización, constituye por tanto el punto de partida de las reflexiones que aquí se presentan. Punto de partida solamente en cuanto su desarrollo en términos de un espacio, requiere de una nueva conceptualización que determine su lógica independientemente de la relación de un «yo» con lo «no- yo». Un espacio independiente del sujeto en el que la experiencia del vivir y la experiencia cultural tienen lugar como creación de sentido de la que resulta el sujeto como efecto de esa creación. La producción de sentido cobra así una importancia capital en la conceptualización de la socialización, por ello, la realizacion del proceso de producción o su impedimento constituyen el eje en el que se instalan o no las disponibilidades para la violencia. La institución se plantea entonces como acción que agencia u obstruye la posibilidad del proceso.

  2. Modelo SPICE compacto para dispositivos e sensores a onda acústica de superfície

    OpenAIRE

    de Moraes Barbosa, Alberto

    2005-01-01

    O desenvolvimento atual em sensores tem como objetivo, uma maior integração entre o componente sensível e o circuito eletrônico para detecção, processamento e comunicação, de maneira que todos os componentes sejam fabricados no mesmo chip. Esse tipo de sensor é denominado genericamente de sensor inteligente integrado (integrated smart sensor). A sua simulação requer modelos que possam ser utilizados em simuladores de circuito. SPICE é um simulador de propósito geral e tem sua estrutura presen...

  3. Wireless Sensor Technologies and Applications

    Directory of Open Access Journals (Sweden)

    Feng Xia

    2009-11-01

    Full Text Available Recent years have witnessed tremendous advances in the design and applications of wirelessly networked and embedded sensors. Wireless sensor nodes are typically low-cost, low-power, small devices equipped with limited sensing, data processing and wireless communication capabilities, as well as power supplies. They leverage the concept of wireless sensor networks (WSNs, in which a large (possibly huge number of collaborative sensor nodes could be deployed. As an outcome of the convergence of micro-electro-mechanical systems (MEMS technology, wireless communications, and digital electronics, WSNs represent a significant improvement over traditional sensors. In fact, the rapid evolution of WSN technology has accelerated the development and deployment of various novel types of wireless sensors, e.g., multimedia sensors. Fulfilling Moore’s law, wireless sensors are becoming smaller and cheaper, and at the same time more powerful and ubiquitous. [...

  4. Optical wheel-rotation sensor

    Energy Technology Data Exchange (ETDEWEB)

    Veeser, L.; Rodriguez, P.; Forman, P. [Los Alamos National Lab., NM (United States); Deeter, M. [National Inst. of Standards and Technology, Boulder, CO (United States)

    1994-05-01

    We describe a fiber-optic rotation sensor based on diffraction of light in a magneto-optic crystal (BIG). Exploitation of this effect permits the construction of a sensor requiring no polarization elements or lenses.

  5. Gait analysis using wearable sensors.

    Science.gov (United States)

    Tao, Weijun; Liu, Tao; Zheng, Rencheng; Feng, Hutian

    2012-01-01

    Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications.

  6. Gait Analysis Using Wearable Sensors

    Directory of Open Access Journals (Sweden)

    Hutian Feng

    2012-02-01

    Full Text Available Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications.

  7. Optimization of biomimetic hair sensors

    NARCIS (Netherlands)

    Izadi, N.; Jaganatharaja, R.K.; Krijnen, Gijsbertus J.M.

    2007-01-01

    High density arrays of artificial hair sensors, biomimicking the extremely sensitive mechanoreceptive filiform hairs found on cerci of crickets have been fabricated. We assess the sensitivity of these artificial sensors and present a scheme for further optimization addressing the deteriorating

  8. Bragg gratings: Optical microchip sensors

    Science.gov (United States)

    Watts, Sam

    2010-07-01

    A direct UV writing technique that can create multiple Bragg gratings and waveguides in a planar silica-on-silicon chip is enabling sensing applications ranging from individual disposable sensors for biotechnology through to multiplexed sensor networks in pharmaceutical manufacturing.

  9. Polymer laser bio-sensors

    DEFF Research Database (Denmark)

    Kristensen, Anders; Vannahme, Christoph; Hermannsson, Pétur Gordon

    2014-01-01

    Organic dye based distributed feed-back lasers, featuring narrow linewidth and thus high quality spectral resolution, are used as highly sensitive refractive index sensors. The design, fabrication and application of the laser intra-cavity sensors are discussed....

  10. Gait Analysis Using Wearable Sensors

    Science.gov (United States)

    Tao, Weijun; Liu, Tao; Zheng, Rencheng; Feng, Hutian

    2012-01-01

    Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phases, the principles and features of wearable sensors used in gait analysis are provided. The gait analysis methods based on wearable sensors is divided into gait kinematics, gait kinetics, and electromyography. Studies on the current methods are reviewed, and applications in sports, rehabilitation, and clinical diagnosis are summarized separately. With the development of sensor technology and the analysis method, gait analysis using wearable sensors is expected to play an increasingly important role in clinical applications. PMID:22438763

  11. Sensor Validation using Bayesian Networks

    Data.gov (United States)

    National Aeronautics and Space Administration — One of NASA’s key mission requirements is robust state estimation. Sensing, using a wide range of sensors and sensor fusion approaches, plays a central role in...

  12. Capacitive Position Sensor For Accelerometer

    Science.gov (United States)

    Vanzandt, Thomas R.; Kaiser, William J.; Kenny, Thomas W.

    1995-01-01

    Capacitive position sensor measures displacement of proof mass in prototype accelerometer described in "Single-Crystal Springs for Accelerometers" (NPO-18795). Sensor is ultrasensitive, miniature device operating at ultra-high frequency and described in more detail in "Ultra-High-Frequency Capacitive Displacement Sensor," (NPO-18675). Advances in design and fabrication of prototype accelerometer also applicable to magnetometers and other sensors in which sensed quantities measured in terms of deflections of small springs.

  13. Fiber Sagnac interferometer temperature sensor

    Energy Technology Data Exchange (ETDEWEB)

    Starodumov, A.N.; Zenteno, L.A.; Monzon, D.; De La Rosa, E. [Centro de Investigaciones en Optica, 37150 Leon, Gto (Mexico)

    1997-01-01

    A modified Sagnac interferometer-based fiber temperature sensor is proposed. Polarization independent operation and high temperature sensitivity of this class of sensors make them cost effective instruments for temperature measurements. A comparison of the proposed sensor with Bragg grating and long-period grating fiber sensors is derived. A temperature-induced spectral displacement of 0.99 nm/K is demonstrated for an internal stress birefringent fiber-based Sagnac interferometer. {copyright} {ital 1997 American Institute of Physics.}

  14. Gait Analysis Using Wearable Sensors

    OpenAIRE

    Hutian Feng; Rencheng Zheng; Tao Liu; Weijun Tao

    2012-01-01

    Gait analysis using wearable sensors is an inexpensive, convenient, and efficient manner of providing useful information for multiple health-related applications. As a clinical tool applied in the rehabilitation and diagnosis of medical conditions and sport activities, gait analysis using wearable sensors shows great prospects. The current paper reviews available wearable sensors and ambulatory gait analysis methods based on the various wearable sensors. After an introduction of the gait phas...

  15. Sensor Network Data Fusion Methods

    Directory of Open Access Journals (Sweden)

    Martynas Vervečka

    2011-03-01

    Full Text Available Sensor network data fusion is widely used in warfare, in areas such as automatic target recognition, battlefield surveillance, automatic vehicle control, multiple target surveillance, etc. Non-military use example are: medical equipment status monitoring, intelligent home. The paper describes sensor networks topologies, sensor network advantages against the isolated sensors, most common network topologies, their advantages and disadvantages.Article in Lithuanian

  16. Wearable Optical Sensors

    KAUST Repository

    Ballard, Zachary S.

    2017-07-12

    The market for wearable sensors is predicted to grow to $5.5 billion by 2025, impacting global health in unprecedented ways. Optics and photonics will play a key role in the future of these wearable technologies, enabling highly sensitive measurements of otherwise invisible information and parameters about our health and surrounding environment. Through the implementation of optical wearable technologies, such as heart rate, blood pressure, and glucose monitors, among others, individuals are becoming more empowered to generate a wealth of rich, multifaceted physiological and environmental data, making personalized medicine a reality. Furthermore, these technologies can also be implemented in hospitals, clinics, point-of-care offices, assisted living facilities or even in patients’ homes for real-time, remote patient monitoring, creating more expeditious as well as resource-efficient systems. Several key optical technologies make such sensors possible, including e.g., optical fiber textiles, colorimetric, plasmonic, and fluorometric sensors, as well as Organic Light Emitting Diode (OLED) and Organic Photo-Diode (OPD) technologies. These emerging technologies and platforms show great promise as basic sensing elements in future wearable devices and will be reviewed in this chapter along-side currently existing fully integrated wearable optical sensors.

  17. Distributed sensor networks

    CERN Document Server

    Rubin, Donald B; Carlin, John B; Iyengar, S Sitharama; Brooks, Richard R; University, Clemson

    2014-01-01

    An Overview, S.S. Iyengar, Ankit Tandon, and R.R. BrooksMicrosensor Applications, David ShepherdA Taxonomy of Distributed Sensor Networks, Shivakumar Sastry and S.S. IyengarContrast with Traditional Systems, R.R. BrooksDigital Signal Processing Background, Yu Hen HuImage-Processing Background Lynne Grewe and Ben ShahshahaniObject Detection and Classification, Akbar M. SayeedParameter Estimation David FriedlanderTarget Tracking with Self-Organizing Distributed Sensors R.R. Brooks, C. Griffin, D.S. Friedlander, and J.D. KochCollaborative Signal and Information Processing: AnInformation-Directed Approach Feng Zhao, Jie Liu, Juan Liu, Leonidas Guibas, and James ReichEnvironmental Effects, David C. SwansonDetecting and Counteracting Atmospheric Effects Lynne L. GreweSignal Processing and Propagation for Aeroacoustic Sensor Networks, Richard J. Kozick, Brian M. Sadler, and D. Keith WilsonDistributed Multi-Target Detection in Sensor Networks Xiaoling Wang, Hairong Qi, and Steve BeckFoundations of Data Fusion f...

  18. Miniaturised optical displacement sensor

    Science.gov (United States)

    Gindele, Frank; Gaul, Frank; Kraus, Silvio; Sigloch, Susanne; Teubner, Ulrich

    2004-09-01

    The primary object presented in this contribution is the miniaturization of a displacement sensor system with the potential for high accuracy measurements and for cost-effective production in polymers. The measurement of linear displacements can be performed by different methods e.g. magnetoresistive, potentiometric, electromagnetic or inductive encoder systems. For movements in the millimeter range and above the most precise systems are based on optical methods. The displacement measurement of our sensor system uses the intensity modulation of two amplitude gratings, moving relative to each other and illuminated by a LED. To increase the system resolution and the signal quality the grating/detector combination is divided into four areas which are phase shifted to each other. The grating period is 25 μm with a geometrical accuracy below 1 μm. The amplitude gratings have been processed on a glass substrate lithographically. Applying electro-discharge machining a miniaturised optical bench for the passive alignment of the optical and the opto-electronic components has been realised. The sensor has an overall size of 6x4x3 mm3 and is designed for the future replication in one single polymer part. In combination with an electronic interpolation the sensor will be capable for a sub-micrometer accuracy.

  19. Flexible magnetoimpidence sensor

    KAUST Repository

    Kavaldzhiev, Mincho

    2015-05-01

    Recently, flexible electronic devices have attracted increasing interest, due to the opportunities they promise for new applications such as wearable devices, where the components are required to flex during normal use[1]. In this light, different magnetic sensors, like microcoil, spin valve, giant magnetoresistance (GMR), magnetoimpedance (MI), have been studied previously on flexible substrates.

  20. Supramolecular Based Membrane Sensors

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Pourjavid

    2006-08-01

    Full Text Available Supramolecular chemistry can be defined as a field of chemistry, which studiesthe complex multi-molecular species formed from molecular components that haverelatively simpler structures. This field has been subject to extensive research over the pastfour decades. This review discusses classification of supramolecules and their application indesign and construction of ion selective sensors.

  1. Composite sensor membrane

    Science.gov (United States)

    Majumdar, Arun [Orinda, CA; Satyanarayana, Srinath [Berkeley, CA; Yue, Min [Albany, CA

    2008-03-18

    A sensor may include a membrane to deflect in response to a change in surface stress, where a layer on the membrane is to couple one or more probe molecules with the membrane. The membrane may deflect when a target molecule reacts with one or more probe molecules.

  2. Ultrasonic corona sensor study

    Science.gov (United States)

    Harrold, R. T.

    1976-01-01

    The overall objective of this program is to determine the feasibility of using ultrasonic (above 20 kHz) corona detection techniques to detect low order (non-arcing) coronas in varying degrees of vacuum within large high vacuum test chambers, and to design, fabricate, and deliver a prototype ultrasonic corona sensor.

  3. Optimal Fusion of Sensors

    DEFF Research Database (Denmark)

    Larsen, Thomas Dall

    within some global frame of reference using a wide variety of sensors providing odometric, inertial and absolute data concerning the robot and its surroundings. Kalman filters have for a long time been widely used to solve this problem. However, when measurements are delayed or the mobile robot...

  4. ISFET based enzyme sensors

    NARCIS (Netherlands)

    van der Schoot, Bart H.; Bergveld, Piet

    1987-01-01

    This paper reviews the results that have been reported on ISFET based enzyme sensors. The most important improvement that results from the application of ISFETs instead of glass membrane electrodes is in the method of fabrication. Problems with regard to the pH dependence of the response and the

  5. Self Calibrating Interferometric Sensor

    DEFF Research Database (Denmark)

    Sørensen, Henrik Schiøtt

    This thesis deals with the development of an optical sensor based on micro interferometric backscatter detection (MIBD). A price effective, highly sensitive and ready for mass production platform is the goal of this project. The thesis covers three areas. The first part of the thesis deals...

  6. Fast Air Temperature Sensors

    DEFF Research Database (Denmark)

    Hendricks, Elbert

    1998-01-01

    The note documents briefly work done on a newly developed sensor for making fast temperature measurements on the air flow in the intake ports of an SI engine and in the EGR input line. The work reviewed has been carried out in close cooperation with Civ. Ing. Michael Føns, the author (IAU...

  7. Carbon dioxide sensor

    Science.gov (United States)

    Dutta, Prabir K [Worthington, OH; Lee, Inhee [Columbus, OH; Akbar, Sheikh A [Hilliard, OH

    2011-11-15

    The present invention generally relates to carbon dioxide (CO.sub.2) sensors. In one embodiment, the present invention relates to a carbon dioxide (CO.sub.2) sensor that incorporates lithium phosphate (Li.sub.3PO.sub.4) as an electrolyte and sensing electrode comprising a combination of lithium carbonate (Li.sub.2CO.sub.3) and barium carbonate (BaCO.sub.3). In another embodiment, the present invention relates to a carbon dioxide (CO.sub.2) sensor has a reduced sensitivity to humidity due to a sensing electrode with a layered structure of lithium carbonate and barium carbonate. In still another embodiment, the present invention relates to a method of producing carbon dioxide (CO.sub.2) sensors having lithium phosphate (Li.sub.3PO.sub.4) as an electrolyte and sensing electrode comprising a combination of lithium carbonate (Li.sub.2CO.sub.3) and barium carbonate (BaCO.sub.3).

  8. La Iglesia como espacio sagrado de encuentro

    Directory of Open Access Journals (Sweden)

    Rodrigo Polanco

    2003-01-01

    Full Text Available Este artículo, a la luz de LG 1, reflexiona sobre la Iglesia como espacio sagrado, es decir, como "lugar de encuentro" de los hombres con Dios y de los hombres entre sí. Espacio es precisamente lo que nos permite el encuentro, y la encarnación del Verbo es la entrada de Dios de manera definitiva y absoluta en el espacio humano. La Iglesia, como Cuerpo de Cristo y Templo del Espíritu es la presencia sacramental del Verbo en medio de la humanidad, y como tal, es lugar de encuentro con el mismo Verbo. Pero además, la Iglesia es Pueblo, es decir, esa presencia sacramental se realiza en personas y en una institucionalidad bien concreta que se transforma en instrumento de la gracia. De allí entonces que a partir de la resurrección de Cristo y de Pentecostés, el mismo Resucitado ha validado las formas institucionales concretas al hacerlas presencia y acciones de sí mismo y como tal, espacio de encuentro consigo mismo, de tal manera que la institucionalidad remita siempre más allá de sí misma, al Dios TrinoThis article, in the light of the LG1, reflects on the church as sacred space, that is a 'meeting place' between God and men, and of men with each other. The space is precisely what allows us to meet, and the Incarnation of the Verb is the definite and absolute coming of God into the human space. The Church, as the Body of Christ and Temple of the Holy Spirit, is the sacramental presence of the Verb amid humanity, and as such, the meeting place with Verb Himself. But the Church is also a people, so this sacramental presence is carried out by persons and in a concrete institutionality, which turns into an instrument of grace. Hence as from the Resurrection of Christ and Pentecost, the same Christ has validated the concrete institutional forms, making them presence and action of Himself, and as such, as space to meet Him, in such a way, that the institutionality always leads beyond Himself, i.e. the Trinity

  9. Integración Kalman de sensores inerciales INS con GPS en un UAV

    OpenAIRE

    Ferrer Mínguez, Gonzalo

    2009-01-01

    El objetivo es estimar la actitud y la posición del UAV (Unmanned Aerial Vehicle) utilizando sensores inerciales y otros sensores: un acelerómetro en 3 ejes, giroscopio en 3 ejes, magnetómetro en 3 ejes y las medidas de posición de un GPS. Todos estos sensores están instalados rígidamente sobre el fuselaje del avión. El objetivo principal del proyecto, es utilizar el avión como plataforma para un radar de apertura sintética (SAR). La principal ventaja respecto a otras plataform...

  10. Magnetic Nanocomposite Cilia Sensors

    KAUST Repository

    Alfadhel, Ahmed

    2016-07-19

    Recent progress in the development of artificial skin concepts is a result of the increased demand for providing environment perception such as touch and flow sensing to robots, prosthetics and surgical tools. Tactile sensors are the essential components of artificial skins and attracted considerable attention that led to the development of different technologies for mimicking the complex sense of touch in humans. This dissertation work is devoted to the development of a bioinspired tactile sensing technology that imitates the extremely sensitive hair-like cilia receptors found in nature. The artificial cilia are fabricated from permanent magnetic, biocompatible and highly elastic nanocomposite material, and integrated on a giant magneto-impedance magnetic sensor to measure the stray field. A force that bends the cilia changes the stray field and is therefore detected with the magnetic sensor, providing high performance in terms of sensitivity, power consumption and versatility. The nanocomposite is made of Fe nanowires (NWs) incorporated into polydimethylsiloxane (PDMS). Fe NWs have a high remanent magnetization, due the shape anisotropy; thus, they are acting as permanent nano-magnets. This allows remote device operation and avoids the need for a magnetic field to magnetize the NWs, benefiting miniaturization and the possible range of applications. The magnetic properties of the nanocomposite can be easily tuned by modifying the NWs concentration or by aligning the NWs to define a magnetic anisotropy. Tactile sensors are realized on flexible and rigid substrates that can detect flow, vertical and shear forces statically and dynamically, with a high resolution and wide operating range. The advantage to operate the sensors in liquids and air has been utilized to measure flows in different fluids in a microfluidic channel. Various dynamic studies were conducted with the tactile sensor demonstrating the detection of moving objects or the texture of objects. Overall

  11. Emissive sensors and devices incorporating these sensors

    Science.gov (United States)

    Swager, Timothy M; Zhang, Shi-Wei

    2013-02-05

    The present invention generally relates to luminescent and/or optically absorbing compositions and/or precursors to those compositions, including solid films incorporating these compositions/precursors, exhibiting increased luminescent lifetimes, quantum yields, enhanced stabilities and/or amplified emissions. The present invention also relates to sensors and methods for sensing analytes through luminescent and/or optically absorbing properties of these compositions and/or precursors. Examples of analytes detectable by the invention include electrophiles, alkylating agents, thionyl halides, and phosphate ester groups including phosphoryl halides, cyanides and thioates such as those found in certain chemical warfare agents. The present invention additionally relates to devices and methods for amplifying emissions, such as those produced using the above-described compositions and/or precursors, by incorporating the composition and/or precursor within a polymer having an energy migration pathway. In some cases, the compositions and/or precursors thereof include a compound capable of undergoing a cyclization reaction.

  12. Expansion of IFC model with structural sensors

    Directory of Open Access Journals (Sweden)

    Rio, J.

    2013-06-01

    Full Text Available The instrumentation and structural health monitoring, SHM, of buildings is a growing field in the construction industry. The goal of this research work is to explore ways of modeling SHM systems, and the resulting data collected from buildings, in standard information management system such as Building Information Models, BIM. These models need to be stored in digital databases with structures suitable for the specific building related information. In this work the Industry Foundation Classes, IFC, data model was used. A case study is presented to assess the applicability of the present IFC standard as a tool to build a three-dimensional digital model of a real instrumented building, as well as some of the structural sensors and their results. The interoperability of the digital model was verified by using different modeling, viewing and analysis software tools. Limitations of the current IFC model were explored and extensions to the sensor classes are proposed.La instrumentación y monitorización de la salud estructural de edificios, SHM, es un campo creciente en la industria de la construcción. El objetivo del presente trabajo es estudiar la modelación de sistemas SHM tomados de edificios en un modelo digital BIM e la sua integración de datos. Estos modelos deben almacenarse en bases de datos con una estructura apropiada para albergar información específica relacionada con la construcción. En este trabajo se utilizó el estándar Industry Foundation Classes, IFC. Se presenta un estudio de caso para evaluar la norma IFC como herramienta para modelar un edificio real instrumentado, así como algunos sensores estruturales e sus resultados. La inter-operatividad de lo modelo digital se ha comprobado mediante el uso de diferentes herramientas de software de modelación, visualización y análisis. Se exploran además limitaciones del modelo IFC y se proponen extensiones de las clases de sensores.

  13. Interfacing Sensors To Micro Controllers

    KAUST Repository

    Norain, Mohamed

    2018-01-15

    This lecture will cover the most common interface and interface techniques between sensors and microcontrollers. The presentation will introduce the pros and cons of each interface type including analogue, digital and serial output sensors. It will also cover the basic required electronics knowledge to help you in selecting and designing your next sensor to microcontroller interface.

  14. USGS VDP Infrasound Sensor Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Slad, George William [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Merchant, Bion J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-01

    Sandia National Laboratories has tested and evaluated two infrasound sensors, the model VDP100 and VDP250, built in-house at the USGS Cascades Volcano Observatory. The purpose of the infrasound sensor evaluation was to determine a measured sensitivity, self-noise, dynamic range and nominal transfer function. Notable features of the VDP sensors include novel and durable construction and compact size.

  15. Micromachined pressure/flow-sensor

    NARCIS (Netherlands)

    Oosterbroek, R.E.; Lammerink, Theodorus S.J.; Berenschot, Johan W.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt; van den Berg, Albert

    The micromechanical equivalent of a differential pressure flow-sensor, well known in macro mechanics, is discussed. Two separate pressure sensors are used for the device, enabling to measure both, pressure as well as volume flow-rate. An integrated sensor with capacitive read-out as well as a

  16. Low-Cost Humidity Sensor

    Science.gov (United States)

    Laue, E. G.

    1986-01-01

    Electronic humidity sensor is simple, inexpensive, and produces output readily used by indicator or control circuits. Sensor operates at safe, low voltage and is relatively invulnerable to electrolysis effects. Sensor used to measure humidity in atmosphere, in soil, and industrial gases, for example.

  17. A Survey of Sensor Network Security

    OpenAIRE

    Vaseashta, A.; S. VASEASHTA

    2008-01-01

    Sensor networks deploy sensor nodes to detect and monitor environmental events and interactions. Existing sensor networks focus on communication within the bounds of resource restrained sensor nodes at the expense of security. In this paper, a review of sensor network components, architectures, algorithms and protocols aims to increase awareness of sensor network limitations and resulting strategies to ensure information security within wireless sensor networks. Because sensor networks deploy...

  18. Activity Recognition Invariant to Sensor Orientation with Wearable Motion Sensors.

    Science.gov (United States)

    Yurtman, Aras; Barshan, Billur

    2017-08-09

    Most activity recognition studies that employ wearable sensors assume that the sensors are attached at pre-determined positions and orientations that do not change over time. Since this is not the case in practice, it is of interest to develop wearable systems that operate invariantly to sensor position and orientation. We focus on invariance to sensor orientation and develop two alternative transformations to remove the effect of absolute sensor orientation from the raw sensor data. We test the proposed methodology in activity recognition with four state-of-the-art classifiers using five publicly available datasets containing various types of human activities acquired by different sensor configurations. While the ordinary activity recognition system cannot handle incorrectly oriented sensors, the proposed transformations allow the sensors to be worn at any orientation at a given position on the body, and achieve nearly the same activity recognition performance as the ordinary system for which the sensor units are not rotatable. The proposed techniques can be applied to existing wearable systems without much effort, by simply transforming the time-domain sensor data at the pre-processing stage.

  19. Distributed estimation for adaptive sensor selection in wireless sensor networks

    Science.gov (United States)

    Mahmoud, Magdi S.; Hassan Hamid, Matasm M.

    2014-05-01

    Wireless sensor networks (WSNs) are usually deployed for monitoring systems with the distributed detection and estimation of sensors. Sensor selection in WSNs is considered for target tracking. A distributed estimation scenario is considered based on the extended information filter. A cost function using the geometrical dilution of precision measure is derived for active sensor selection. A consensus-based estimation method is proposed in this paper for heterogeneous WSNs with two types of sensors. The convergence properties of the proposed estimators are analyzed under time-varying inputs. Accordingly, a new adaptive sensor selection (ASS) algorithm is presented in which the number of active sensors is adaptively determined based on the absolute local innovations vector. Simulation results show that the tracking accuracy of the ASS is comparable to that of the other algorithms.

  20. A Survey of Visual Sensor Networks

    National Research Council Canada - National Science Library

    Soro, Stanislava; Heinzelman, Wendi

    2009-01-01

    ..., recent developments in sensor networking and distributed processing have encouraged the use of image sensors in these networks, which has resulted in a new ubiquitous paradigm--visual sensor networks. Visual sensor networks (VSNs) consist of tiny visual sensor nodes called camera nodes, which integrate the image sensor, embedded processor, and wireless tra...

  1. Open Standards for Sensor Information Processing

    Energy Technology Data Exchange (ETDEWEB)

    Pouchard, Line Catherine [ORNL; Poole, Stephen W [ORNL; Lothian, Josh [ORNL

    2009-07-01

    This document explores sensor standards, sensor data models, and computer sensor software in order to determine the specifications and data representation best suited for analyzing and monitoring computer system health using embedded sensor data. We review IEEE 1451, OGC Sensor Model Language and Transducer Model Language (TML), lm-sensors and Intelligent Platform Management Inititative (IPMI).

  2. Smart Home Wireless Sensor Nodes

    DEFF Research Database (Denmark)

    Lynggaard, Per

    Smart homes are further development of intelligent buildings and home automation, where context awareness and autonomous behaviour are added. They are based on a combination of the Internet and emerging technologies like wireless sensor nodes. These wireless sensor nodes are challenging because....... This paper introduces an approach that considerably lowers the wireless sensor node power consumption and the amount of transmitted sensor events. It uses smart objects that include artificial intelligence to efficiently process the sensor event on location and thereby saves the costly wireless...

  3. Las plazas de mercado como catalizadores urbanos

    OpenAIRE

    Baquero Duarte, Diana Lizeth

    2011-01-01

    Este trabajo final de diseño urbano, se propone desarrollar una guía de diseño urbano para apoyar la solución de conflictos de uso y configuración espacial existente entre las plazas de mercado con su entorno inmediato en la ciudad de Bogotá; con el propósito de generar una articulación entre estos equipamientos con su contexto inmediato y una respuesta adecuada al usuario, afianzando su función utilitaria y simbólica a partir de su potencial como generadores de centralidad basados en el enfo...

  4. El arte como forma de conocimiento

    OpenAIRE

    Camnitzer, Luis

    2016-01-01

    Quiero empezar esto con unas declaraciones que darán un contexto para precisar un poco lo que voy a decir. Lo primero es que soy un artista y nada más que un artista. Esto no significa que a veces caiga en temas y zonas a los que no pertenezco. Es algo que hago a cada rato y siempre ofrezco opiniones sobre cosas en las cuales soy un ignorante total. Pero eso solamente significa que no me doy cuenta cuando me meto en esos temas o qué tengo que considerarlos como temas distintos a los que conoz...

  5. Como Lo Hago Yo: Mielomeningocele En Bolivia

    OpenAIRE

    Dabdoub, Carlos F.; Dabdoub, Carlos B.; Villavicencio, Ramiro; Quevedo, Germán

    2014-01-01

    Introducción: Las malformaciones del tubo neural (MTN) representan la segunda causa más frecuente de anomalías congénitas, luego de las cardiopatías. En este grupo se destaca el mielomeningocele (MMC) por su mayor incidencia, y por ser la más incapacitante y la más compleja entre todas las demás malformaciones del sistema nervioso c`entral (SNC). En Bolivia, como en muchos países de Sudamérica, los bajos niveles socio-culturales y la debilidad en el sistema sanitario, hacen que su incidencia ...

  6. O consumismo como um novo iluminismo

    OpenAIRE

    Santos, Eduardo Alexandre Amaral dos

    2006-01-01

    Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia de Produção. O presente trabalho de pesquisa, com base em referências teóricas, investiga e identifica os mecanismos pelos quais o consumismo, amplamente amparado pelos meios de comunicação de massa, tornou-se um complexo significante do modo de vida na sociedade contemporânea. Para chegar a tais resultados foram mapeadas as raízes da cultura de consumo, bem como...

  7. La moral hobbesiana como equilibrio de mercado

    OpenAIRE

    Hernando Grueso Hurtado

    2013-01-01

    Este escrito constituye una lectura económica de la obra de Thomas Hobbes, dirigida a entender conductas morales como resultado de equilibrios de mercado. Partiendo de una economía de intercambio donde el precio de los bienes obedece a su costo de oportunidad, se muestra usando Teoría de Juegos el surgimiento de conductas morales en un escenario anterior a la formación del Estado. Cuando el Estado ha sido consolidado dejan de ser posibles los comportamientos estratégicos y surge la posibilida...

  8. Los cuentos motores como recurso interdisciplinar

    OpenAIRE

    Herrera Muñoz, María

    2017-01-01

    La finalidad de este Trabajo de Fin de Grado es comprobar la viabilidad y resultados de la puesta en práctica de un programa de educación motriz en Educación Infantil, que está basado fundamentalmente en el recurso de los “cuentos motores” desde un enfoque globalizador. El programa de motricidad globalizado está compuesto por siete sesiones, en las que se trabajaron tres cuentos motores en lengua española y dos en lengua inglesa. Los principales resultados son: como maestra, la importancia de...

  9. La Escuela como lugar de desencuentro intercultural

    Directory of Open Access Journals (Sweden)

    Luis Fernando Estrada Escobar

    2011-12-01

    Full Text Available El reconocimiento político de los derechos de las minorías étnicas implicó la emergencia de una multiplicidad de propuestas formativas para los y las docentes en estos contextos de mayoría afrodescendiente. La tesis de la escuela como lugar de desencuentro intercultural que desarrolla el artículo, surge a partir de las reflexiones que se dieron en una de estas propuestas de formación en Investigación Educativa con docentes de los municipios de Vigía del Fuerte y Murindó, en el Urabá antioqueño.

  10. La inteligencia emocional como estrategia educativa inclusiva

    OpenAIRE

    Fernández Rodicio, Clara Isabel

    2011-01-01

    La educación inclusiva es, sin duda, uno de los temas estrellas que ocupa las agendas de la política educativa. Temas como la atención a la diversidad, la intervención social, conlleva a que le sistema educativo defina las estrategias para el desarrollo integral de la persona, desde la concepción de la integración que implique la intervención fundamental de la familia, la escuela, la comunidad y las instituciones en general. En este contexto educativo, adquiere una especial signif...

  11. ESPACIOS RENATURALIZADOS COMO AMBIENTES DE APRENDIZAJE

    OpenAIRE

    Yenny Rosas; Helena Sepúlveda

    2015-01-01

    El presente escrito, es un informe parcial de aspectos conceptuales y técnicos, implicados en el marco del Convenio Interinstitucional 03258/2013, suscrito entre la Secretaría de Educación Distrital y el Jardín Botánico José Celestino Mutis, denominado: “Colegios verdes, mejores entornos de aprendizajes”; se toma como estudio de caso, la experiencia en la Institución Educativa Distrital Aguas Claras, ubicada en la cuenca Alta del Rio Fucha, en la localidad de San Cristóbal. Los espacios re...

  12. La entrevista como encuentro de subjetividades

    Directory of Open Access Journals (Sweden)

    Emma Ruiz Martín del Campo

    2003-01-01

    Full Text Available Se parte de la comprensión de la subjetividad como la expresión preñada de cultura de cada ser humano que se gesta en las relaciones interpersonales, primero entre el infante y las personas que le prodigan los cuidados tempranos, y después en la adolescencia y la edad adulta, con cada vez más representantes de la cultura de la socialización. En dicha interacción, la persona aprende a convivir con otros y a modelar sus impulsos, lo que le permite encontrar las formas más satisfactorias posibles de experimentarse a sí misma y tomar parte en las actividades de su entorno social. El equilibrio entre el individuo que busca satisfacer sus impulsos y necesidades y la cultura a la que pertenece es dinámico, por lo que la subjetividad se transforma a lo largo de toda la vida. Tras abundar sobre la subjetividad, se describen dos formas de orientar la entrevista a profundidad: la psicoanalítica y la etnopsicoanalítica. La entrevista psicoanalítica explora la subjetividad como tal y en ella el entrevistador actúa como un acompañante del sujeto en la progresiva comprensión de sí mismo y de su historia individual, desentrañando significados del comportamiento hasta entonces inconscientes para sí mismo, que se clarifican en la interacción. La entrevista etnopiscoanalítica busca explorar la experiencia cultural de las personas. Expertos en ciencias sociales entrenados a la vez en el descubrimiento del inconsciente se involucran en un medio cultural nuevo para ellos y a través de entrevistas y conversaciones con los integrantes de la comunidad que visitan van descubriendo formas de participación de estos en los espacios de vida social, así como las maneras que dan cuenta de símbolos y modos de reacción propios de su cultura. Cada una de estas dos formas de entrevista es ilustrada con un ejemplo que da muestra plásticamente del encuentro de las subjetividades

  13. Justicia juvenil restaurativa como respuesta alternativa

    OpenAIRE

    Mariño Rojas, Cielo

    2016-01-01

    El artículo explora las posibilidades de la justicia juvenil restaurativa como respuesta alternativa en los sistemas de justicia juvenil en la región. Si bien la justicia restaurativa no aparece explícitamente en los instrumentos internacionales sobre justicia penal juvenil, estos dan la oportunidad para que aquella se desarrolle dentro de los sistemas de justicia juvenil. Inicialmente se aborda su evolución histórica para establecer el origen de sus principales características. A continuació...

  14. Radio universitaria: trabajo en red como imperativo

    Directory of Open Access Journals (Sweden)

    Tiziana Cavallo

    2014-01-01

    Full Text Available Trabajo en red es un concepto clave en la radio universitaria, tanto desde el punto de vista individual como del colectivo. A través de dos estudios de caso, enfocados en la radio universitaria de Italia y de Colombia, este artículo muestra cómo el trabajo en red ha sido decisivo para el fortalecimiento de su función, la ampliación de su impacto, la conformación de su identidad y el crecimiento de su visibilidad en las sociedades en las cuales desarrollan su labor.

  15. La fatiga como estado motivacional subjetivo

    Directory of Open Access Journals (Sweden)

    D. Cárdenas

    2017-03-01

    No obstante, la tendencia actual es entender la fatiga como un estado motivacional complejo cuyo origen tiene lugar en numerosos procesos fisiológicos y psicológicos que sirven para regular el esfuerzo y proteger al organismo de daños graves. Los objetivos de la presente revisión narrativa son analizar los diferentes enfoques existentes para el estudio y la explicación de la fatiga, establecer el vínculo con el concepto de carga de entrenamiento y justificar la importancia de evaluar las repercusiones de la carga mental para conseguir una adecuada planificación y control del proceso de entrenamiento.

  16. Communications for unattended sensor networks

    Science.gov (United States)

    Nemeroff, Jay L.; Angelini, Paul; Orpilla, Mont; Garcia, Luis; DiPierro, Stefano

    2004-07-01

    The future model of the US Army's Future Combat Systems (FCS) and the Future Force reflects a combat force that utilizes lighter armor protection than the current standard. Survival on the future battlefield will be increased by the use of advanced situational awareness provided by unattended tactical and urban sensors that detect, identify, and track enemy targets and threats. Successful implementation of these critical sensor fields requires the development of advanced sensors, sensor and data-fusion processors, and a specialized communications network. To ensure warfighter and asset survivability, the communications must be capable of near real-time dissemination of the sensor data using robust, secure, stealthy, and jam resistant links so that the proper and decisive action can be taken. Communications will be provided to a wide-array of mission-specific sensors that are capable of processing data from acoustic, magnetic, seismic, and/or Chemical, Biological, Radiological, and Nuclear (CBRN) sensors. Other, more powerful, sensor node configurations will be capable of fusing sensor data and intelligently collect and process data images from infrared or visual imaging cameras. The radio waveform and networking protocols being developed under the Soldier Level Integrated Communications Environment (SLICE) Soldier Radio Waveform (SRW) and the Networked Sensors for the Future Force Advanced Technology Demonstration are part of an effort to develop a common waveform family which will operate across multiple tactical domains including dismounted soldiers, ground sensor, munitions, missiles and robotics. These waveform technologies will ultimately be transitioned to the JTRS library, specifically the Cluster 5 requirement.

  17. Advanced Wireless Sensor Nodes - MSFC

    Science.gov (United States)

    Varnavas, Kosta; Richeson, Jeff

    2017-01-01

    NASA field center Marshall Space Flight Center (Huntsville, AL), has invested in advanced wireless sensor technology development. Developments for a wireless microcontroller back-end were primarily focused on the commercial Synapse Wireless family of devices. These devices have many useful features for NASA applications, good characteristics and the ability to be programmed Over-The-Air (OTA). The effort has focused on two widely used sensor types, mechanical strain gauges and thermal sensors. Mechanical strain gauges are used extensively in NASA structural testing and even on vehicle instrumentation systems. Additionally, thermal monitoring with many types of sensors is extensively used. These thermal sensors include thermocouples of all types, resistive temperature devices (RTDs), diodes and other thermal sensor types. The wireless thermal board will accommodate all of these types of sensor inputs to an analog front end. The analog front end on each of the sensors interfaces to the Synapse wireless microcontroller, based on the Atmel Atmega128 device. Once the analog sensor output data is digitized by the onboard analog to digital converter (A/D), the data is available for analysis, computation or transmission. Various hardware features allow custom embedded software to manage battery power to enhance battery life. This technology development fits nicely into using numerous additional sensor front ends, including some of the low-cost printed circuit board capacitive moisture content sensors currently being developed at Auburn University.

  18. SERS sensors for DVD platform

    DEFF Research Database (Denmark)

    Brøgger, Anna Line

    This Ph.D. thesis explores the engineering of a portable sensor system for detection of rare and small molecules. The Ph.D. project is part of the research project 'Multi-Sensor DVD platform' (MUSE), aiming to integrate different sensors on a rotating disc. The sensors are chosen to complement each...... other, creating more reliable and stable results for the end user. The rotating disc comprises microfluidic channels, which can be utilized for handling and manipulating liquid samples such as blood or water. The focus of this Ph.D. thesis, is on the integration of one specific sensor on a rotating disc....... The sensor is based upon surface enhanced Raman spectroscopy (SERS), which detects molecular vibrations. The aim of this thesis is to cover the different aspects of the sensor system. SERS substrates, consisting of nanopillars with gold or silver caps on top, have been fabricated by standard micro and nano...

  19. Reputation-based secure sensor localization in wireless sensor networks.

    Science.gov (United States)

    He, Jingsha; Xu, Jing; Zhu, Xingye; Zhang, Yuqiang; Zhang, Ting; Fu, Wanqing

    2014-01-01

    Location information of sensor nodes in wireless sensor networks (WSNs) is very important, for it makes information that is collected and reported by the sensor nodes spatially meaningful for applications. Since most current sensor localization schemes rely on location information that is provided by beacon nodes for the regular sensor nodes to locate themselves, the accuracy of localization depends on the accuracy of location information from the beacon nodes. Therefore, the security and reliability of the beacon nodes become critical in the localization of regular sensor nodes. In this paper, we propose a reputation-based security scheme for sensor localization to improve the security and the accuracy of sensor localization in hostile or untrusted environments. In our proposed scheme, the reputation of each beacon node is evaluated based on a reputation evaluation model so that regular sensor nodes can get credible location information from highly reputable beacon nodes to accomplish localization. We also perform a set of simulation experiments to demonstrate the effectiveness of the proposed reputation-based security scheme. And our simulation results show that the proposed security scheme can enhance the security and, hence, improve the accuracy of sensor localization in hostile or untrusted environments.

  20. Rigid particulate matter sensor

    Science.gov (United States)

    Hall, Matthew [Austin, TX

    2011-02-22

    A sensor to detect particulate matter. The sensor includes a first rigid tube, a second rigid tube, a detection surface electrode, and a bias surface electrode. The second rigid tube is mounted substantially parallel to the first rigid tube. The detection surface electrode is disposed on an outer surface of the first rigid tube. The detection surface electrode is disposed to face the second rigid tube. The bias surface electrode is disposed on an outer surface of the second rigid tube. The bias surface electrode is disposed to face the detection surface electrode on the first rigid tube. An air gap exists between the detection surface electrode and the bias surface electrode to allow particulate matter within an exhaust stream to flow between the detection and bias surface electrodes.

  1. Biodegradable micromechanical sensors

    DEFF Research Database (Denmark)

    Keller, Stephan Sylvest; Greve, Anders; Schmid, Silvan

    The development of biopolymers for food packaging, medical engineering or drug delivery is a growing field of research [1]. At the same time, the interest in methods for detailed analysis of biopolymers is increasing. Micromechanical sensors are versatile tools for the characterization...... of biopolymers to microfabrication is challenging, as these polymers are affected by common processes such as photolithography or wet etching. Here, we present two methods for fabrication of biodegradable micromechanical sensors. First, we fabricated bulk biopolymer microcantilevers using nanoimprint lithography...... (NIL). Second, we used spray-coating to deposit thin biodegradable films on microcantilevers. Both approaches allowed the determination of the Young’s modulus of the biopolymer. Furthermore, biodegradation by enzymes was investigated....

  2. Single Nanoparticle Plasmonic Sensors

    Directory of Open Access Journals (Sweden)

    Manish Sriram

    2015-10-01

    Full Text Available The adoption of plasmonic nanomaterials in optical sensors, coupled with the advances in detection techniques, has opened the way for biosensing with single plasmonic particles. Single nanoparticle sensors offer the potential to analyse biochemical interactions at a single-molecule level, thereby allowing us to capture even more information than ensemble measurements. We introduce the concepts behind single nanoparticle sensing and how the localised surface plasmon resonances of these nanoparticles are dependent upon their materials, shape and size. Then we outline the different synthetic approaches, like citrate reduction, seed-mediated and seedless growth, that enable the synthesis of gold and silver nanospheres, nanorods, nanostars, nanoprisms and other nanostructures with tunable sizes. Further, we go into the aspects related to purification and functionalisation of nanoparticles, prior to the fabrication of sensing surfaces. Finally, the recent developments in single nanoparticle detection, spectroscopy and sensing applications are discussed.

  3. Thin film hydrogen sensor

    Science.gov (United States)

    Lauf, R.J.; Hoffheins, B.S.; Fleming, P.H.

    1994-11-22

    A hydrogen sensor element comprises an essentially inert, electrically-insulating substrate having a thin-film metallization deposited thereon which forms at least two resistors on the substrate. The metallization comprises a layer of Pd or a Pd alloy for sensing hydrogen and an underlying intermediate metal layer for providing enhanced adhesion of the metallization to the substrate. An essentially inert, electrically insulating, hydrogen impermeable passivation layer covers at least one of the resistors, and at least one of the resistors is left uncovered. The difference in electrical resistances of the covered resistor and the uncovered resistor is related to hydrogen concentration in a gas to which the sensor element is exposed. 6 figs.

  4. Tecnologia como fundamento do cuidar em Neonatologia

    Directory of Open Access Journals (Sweden)

    José Antonio de Sá Neto

    2010-01-01

    Full Text Available Se trata de un artículo sobre la evolución histórica de la tecnología en neonatología, resaltando aspectos conceptuales y reflexivos sobre el impacto tecnológico en el proceso de cuidar. A pesar de que en los últimos años, la tecnología ha contribuido para mejorar la supervivencia de prematuros extremos nacidos con muy bajo peso, algunas veces da lugar a una modalidad de atención mecánica e impersonal, que se contrapone a cuestiones de índole ética y humana. Se propone una discusión crítica y reflexiva acerca del uso de la tecnología en el cuidado neonatal, destacando sus implicaciones y adecuaciones a las necesidades del recién nacido. Se concluyó que lo que determina si una tecnología es buena o mala, si deshumaniza, despersonaliza o interpreta como objeto al sujeto a cuidar, es la manera como es utilizada, convirtiéndose en imprescindible el perfeccionamiento y la actualización de los profesionales de la salud. En este ejercicio análitico es necesario reflexionar acerca de nuevas maneras de brindar cuidados, utilizando el arte, la sensibilidad y la creatividad en la adaptación y humanización de las tecnologías.

  5. El arquitecto como educador de la sociedad

    Directory of Open Access Journals (Sweden)

    Maria Montoro

    2017-07-01

    Full Text Available El concurso para el monumento a Federico II fue convocado por primera vez el 25 de enero de 1787, en un momento marcado por la profunda crisis que a todos los niveles atravesaba el Sacro Imperio Romano Germánico. La necesidad de revertir la mala situación existente hizo que una parte importante de la intelectualidad alemana apuntase a la educación como único medio de regeneración posible. En este sentido, un buen número de propuestas escultóricas relacionaban al monarca con la figura del filósofo. Por su parte, los proyectos presentados por Hans Christian Genelli, Carl Gotthard Langhans, Heinrich Gentz y Friedrich Gilly, desarrollaban diversas estrategias utilizando la arquitectura como medio para producir una mejora en la vida del hombre, desde el mero embellecimiento estético planteado por Langhans, pasando por la capacidad de abstracción de la belleza reivindicada por Gentz, hasta el edificio educativo proyectado por Gilly quien, con su propuesta para el monumento, construye un mecanismo capaz de transformar al gobernante en filósofo.

  6. Conocimiento como diseño

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Garzón Gaitán

    1998-06-01

    Full Text Available El artículo es una síntesis de un trabajo experimental en curso que tiene un hilo conductor: la educación en ingeniería y la preocupación acerca de cómo mejorarla; específicamente se busca precisar qué papel desempeña el diseño en la creación de capacidades tecnológicas, especialmente de innovación, en nuestros ingenieros para poder incidir en el desarrollo nacional y como la mejor manera de aprender. Se mostrará que diseño y aprendizaje tienen estructuras paralelas y, por tanto, la formación de ingenieros e innovadores debe darse en un doble sentido: aprendiendo a diseñar y aprender diseñando; se argumentará, además, como los problemas débilmente estructurados contribuyen a la creación de las competencias deseadas en los ingenieros.

  7. Quitina y carboximetilquitosana como agentes desintegrantes

    Directory of Open Access Journals (Sweden)

    Sol A Fernández Monagas

    1998-08-01

    Full Text Available Se realizó un estudio comparativo de la quitina y la carboximetilquitosana como agentes desintegrantes, y se evaluó la influencia ejercida por el método empleado en la elaboración de las tabletas sobre la actividad desintegrante de ambos polímeros. La quitina presentó buenas características como agente desintegrante independientemente del método utilizado en la elaboración de las tabletas, mientras que la actividad desintegrante de la carboximetilquitosana fue afectada por el proceso de granulación.A comparative study of chitin and carboxymethylchitosan as disintegrating agents was wade made. The influence exerted bu tje method used in the preparation of the tablets on the disintegrating activity of both polymers was evaluated. Chitin proved to have good characteristics as a disintegrating agent independently of the method used to make tablets. The disintegrating activity of carboxymethylchitosan was affected by the granulation process.

  8. A Liberdade como tema: um debate italiano

    Directory of Open Access Journals (Sweden)

    Rego Walquiria D. Leão

    2002-01-01

    Full Text Available O presente trabalho rememora e analisa os termos e as categorias mobilizadas no debate teórico e político, sobre a questão da liberdade, realizado entre liberais-socialistas e comunistas italianos ocorrido nos anos vinte e trinta do século XX. De certo modo, a polêmica esteve presente na fundação mesma do Partido Comunista Italiano, através das reflexões teóricas e da colaboração estreita existente entre o liberal, Piero Gobetti e o marxista, Antonio Gramsci. O diálogo acompanhou a vida do PCI nos mais diversos momentos de sua história, tanto nos momentos de compartilhamento cívico, como o da luta antifascista e a organização da resistência, como nos tempos de reconstrução da Itália nos anos de 1950. Polemizaram assim, pelo lado liberal socialista, Norberto Bobbio, e pelo comunista, o então secretário geral do P.C.I., Palmiro Togliatti.

  9. como herramienta de educación

    Directory of Open Access Journals (Sweden)

    Adriana Kong Montoya

    2016-01-01

    Full Text Available El acceso a las Tecnologías de la Información y Comunicación (TIC es limitado por la brecha digital. Se genera una desigualdad de acceso a la información que influye en el desarrollo de la educación. Se habla también de una brecha cognitiva que interviene en diferentes manifestaciones y dinámicas sociales. Las herramientas de comunicación en la sociedad se ven limitadas a algunos segmentos reducidos de la población. La producción audiovisual se limita a algunos usuarios y esto genera productos que no reflejan a una comunidad en su totalidad. El cine comunitario posee las características que favorecen el desarrollo de la identidad, la visibilizarían de problemas y el acceso de las comunidades a herramientas de las TIC. Esta forma de producción surge como respuesta de una responsabilidad social y funciona como herramienta alternativa para combatir las sociedades marginadas por la brecha digital.

  10. Guatemala como alternativa de desarrollo local

    Directory of Open Access Journals (Sweden)

    Rosa Elba Hernandez Cruz

    2015-01-01

    Full Text Available El área aledaña a la Reserva de la biósfera del Volcán Tacaná, en Chiapas México destaca por la producción de café, además de una alta diversidad de flora y fauna; sin embargo las comunidades rurales que habitan estos espacios están en constante búsqueda de alternativas productivas para mejorar sus medios de vida y cuidar el ambiente el cual está sufriendo deterioro. Ante esta situación se planteó como objetivo la integración de una red de fincas agroecoturísticas en los municipios de Cacahoatán, Tuxtla Chico, Unión Juárez en Chiapas, México y una comunidad en Guatemala. Para construir la propuesta se utilizó la metodología de modos de vida, se realizaron talleres participativos, recorridos en campo y se identificaron los productos turísticos. Se concluye, a partir del análisis de los modos de vida, que la región presenta características y oportunidades para desarrollar la red de agroecoturismo como una alternativa económica.

  11. Las comunidades locales como estructuras meso.

    Directory of Open Access Journals (Sweden)

    Ferrand, Alexis

    2002-09-01

    Full Text Available Entre el nivel micro y el nivel macro: meso. Si el nivel macro está definido por la regulación nacional, estatal o del mercado y el nivel micro por la regulación interpersonal, una agencia de regulación intermediaria de mayor importancia ha sido definida como “comunidad local” (Wellman, Fischer. Aparte de las dimensiones organizacionales (organizaciones locales, clubes, tiendas... e institucionales (poder local, partidos... locales, es posible definir algunas propiedades estructurales pertinentes de los sistemas de relaciones interpersonales privadas: uno es el grado de “cerrado” (closure local (Barnes: redes locales vs. transversales, o la “dualidad” de estos sistemas. Apoyándose en la idea de que la eficiencia de los “puentes” reside en el tipo de cliques que conectan (Lin, es posible definir tipos variados de micro-estructuras, cuyas distribuciones en diferentes localidades son indicadores sucedáneos o aproximaciones de las diferentes meso estructuras de sistemas relacionales como combinaciones de redes “locales” y “no locales”.

  12. El lenguaje como instrumento de poder

    Directory of Open Access Journals (Sweden)

    MARÍA TERESA SUÁREZ GONZÁLEZ

    2009-01-01

    Full Text Available La investigación denominada 'El lenguaje como instrumento de poder' planteó dos interrogantes que permitieron, por un lado, evidenciar ¿cuáles estrategias discursivas permiten analizar la relación entre lenguaje y poder en el discurso de la segunda posesión del presidente Álvaro Uribe Vélez y, por otro, analizar las implicaciones que tienen las mencionadas estrategias en la construcción de sentido. Lo anterior con el fin de mirar cómo se ejerce poder mediante las prácticas discursivas, dado que quien emite un discurso busca, ante todo, convencer y cambiar la mentalidad de los receptores, a través de la comunicación de creencias, actitudes, valores y un sinnúmero de saberes tomados de su entorno y de la cultura, por medio de estrategias discusivas que son empleadas de manera consciente, de acuerdo con el fin que se persiga. Teniendo en cuenta lo anterior, esta ponencia presenta los resultados obtenidos en la investigación, desarrollada en la Maestría en Lingüística de la UPTC, los cuales muestran el discurso como una interacción a través de la cual se evidencian marcas de poder y se construyen los acontecimientos y las identidades de los sujetos, mediante la comunicación.

  13. El manual como texto Schoolbook as text

    Directory of Open Access Journals (Sweden)

    Agustín Escolano Benito

    2012-12-01

    Full Text Available Este trabajo aborda la cuestión de la identidad del libro escolar como un género textual específico en el contexto de la manualística clásica y moderna, contextualizando los análisis en el marco de la cultura de la escuela tradicional y en la era de la revolución digital y bajo una perspectiva historiográfica y teórica. También plantea el nacimiento y primeros desarrollos de la manualística como campo intelectual y académico y sus contribuciones a la definición de la identidad del libro escolar.This paper discusses the question of identifying a coursebook as a specific text genre in the context of the classical and modern manualistics, situating the analysis within the traditional school culture and the digital revolution era, under a historical and theoretical perspective. It also covers the birth and initial development of manualistics as an intelectual and academic field and its contributions to the definition of the schoolbook identity.

  14. Marañón como modelo

    Directory of Open Access Journals (Sweden)

    Gracia, Diego

    2013-02-01

    Full Text Available As a result of his consistent attitude as citizen and doctor and his “liberal spirit”, Marañón has gone down in the history of the twentieth century as an archetype. Marañón was, above all, a moralist in the Kantian sense, an autonomous person not governed by external criteria but by duty; a thinker convinced of the transforming role of the positive sciences, towards a happier and more just society through a deep intellectual reform. Marañón, like Fernando de los Rios, integrated Kraussism, neo-Kantianism and socialism and from this ideological platform sought the necessary moral change in the Spanish people.Marañón ha pasado a la historia del siglo XX como arquetipo, debido a su actitud coherente y a su “talante liberal”. Marañón fue, sobre todo, un moralista en el sentido kantiano. Una persona autónoma que no se rigió por criterios externos, sino por deber; un convencido del papel transformador de las ciencias positivas en pos de una sociedad más feliz y más justa gracias a una profunda reforma intelectual. Marañón, como Fernando de los Ríos, integró krausismo, neokantismo y socialismo y desde esa plataforma ideológica, propugnó el necesario cambio moral del pueblo español.

  15. Bloque de tierra comprimida como material constructivo

    Directory of Open Access Journals (Sweden)

    Óscar Javier Gutiérrez Junco

    2011-07-01

    Full Text Available La construcción con tierra es poco usada en la actualidad debido a la falta de difusión e investigación, y a que es relacionada con la pobreza; por ende, se desaprovechan muchas de sus ventajas, como la abundancia demateria prima, la localización, la disponibilidad, el reciclaje, la producción sin consumo de energía (calorífica, el bajo costo y la resistencia –con un adecuado estudio del material tierra, de la estructuración y del suelo de fundación–; otras de sus ventajas son el aislamiento térmico y acústico. Con el paso del tiempo se han mejorado las técnicas constructivas con tierra, realizando estabilizaciones e implementando el uso de maquinaria y herramienta mecánica para elaborar bloques de tierra comprimida, y así facilitar el trabajo y obtener mayor rendimiento. Este artículo presenta la tierra como material constructivo, las técnicas o sistemas constructivos, los bloques de tierra comprimida (BTC y algunos ensayos realizados a estos bloques.

  16. Magnetic Resonance Sensors

    OpenAIRE

    Morris, RH; Newton, MI

    2014-01-01

    Magnetic Resonance finds countless applications, from spectroscopy to imaging, routinely in almost all research and medical institutions across the globe. It is also becoming more frequently used for specific applications in which the whole instrument and system is designed for a dedicated application. With beginnings in borehole logging for the petro-chemical industry Magnetic Resonance sensors have been applied to fields as varied as online process monitoring for food manufacture and medica...

  17. Sensors in Smartphones

    OpenAIRE

    Hu, Mengchen

    2010-01-01

    With the booming development of scientific technology, the mobile phone is no longer a simple communication tool, but a portable electronic device with integrated functions. You can use the phone to listen to music, watch movies, take pictures and so on. Mobile phones have gradually entered into human’s daily life. In this case, the various sensors are emerged in smartphones. The requirements on smartphones are increasingly high. Telephone, SMS, multimedia, etc., are just basic applications,...

  18. Microfabricated Formaldehyde Gas Sensors

    OpenAIRE

    Cheung, Karen C.; Ko, Frank K.; Jonas Flueckiger

    2009-01-01

    Formaldehyde is a volatile organic compound that is widely used in textiles, paper, wood composites, and household materials. Formaldehyde will continuously outgas from manufactured wood products such as furniture, with adverse health effects resulting from prolonged low-level exposure. New, microfabricated sensors for formaldehyde have been developed to meet the need for portable, low-power gas detection. This paper reviews recent work including silicon microhotplates for metal oxide-based d...

  19. Image processing occupancy sensor

    Science.gov (United States)

    Brackney, Larry J.

    2016-09-27

    A system and method of detecting occupants in a building automation system environment using image based occupancy detection and position determinations. In one example, the system includes an image processing occupancy sensor that detects the number and position of occupants within a space that has controllable building elements such as lighting and ventilation diffusers. Based on the position and location of the occupants, the system can finely control the elements to optimize conditions for the occupants, optimize energy usage, among other advantages.

  20. Multicolor LED sensor

    Science.gov (United States)

    Lange, Volker; Ribeiro, Felipe; Tews, Walter; Kühlke, Dietrich

    2008-04-01

    We present a compact and cheap sensor device based on the combination of a standard RGB-LED with a luminescence material. The multicolor LED acts as the exciting light source, the luminescence light detector and simultaneously as an optical filter. As luminescence material various phosphor materials or crystals can be used, depending on the physical property to be sensed. Possible applications will be discussed.

  1. remote sensor network

    Science.gov (United States)

    von Unold, Georg; Junker, Astrid; Altmann, Thomas

    2016-04-01

    High-throughput (HT) plant phenotyping systems enable the quantitative analysis of a variety of plant features in a fully automated fashion. The comprehensive phenomics infrastructure at IPK comprises three LemnaTec conveyor belt-based (plant-to-sensor) systems for the simultaneous analysis of large numbers of individual plants of different sizes. For monitoring of environmental conditions within the plant growth area and soil conditions in individual pots, highly modular and flexible remote sensing devices are required. We present the architecture of a wireless sensor network implemented in the HT plant phenotyping systems at IPK in the frame of the German Plant Phenotyping Network (DPPN). This system comprises 350 soil monitoring modules, each measuring water content, water matrix potential, temperature and electric conductivity. Furthermore small and large sensor platforms enable the continuous monitoring of environmental parameters such as incident photosynthetic active radiation, total radiation balance, relative humidity and CO2 concentration and more. Finally we present an introduction into data management and maintenance."

  2. Piezoelectric cantilever sensors

    Science.gov (United States)

    Shih, Wan Y. (Inventor); Shih, Wei-Heng (Inventor); Shen, Zuyan (Inventor)

    2008-01-01

    A piezoelectric cantilever with a non-piezoelectric, or piezoelectric tip useful as mass and viscosity sensors. The change in the cantilever mass can be accurately quantified by monitoring a resonance frequency shift of the cantilever. For bio-detection, antibodies or other specific receptors of target antigens may be immobilized on the cantilever surface, preferably on the non-piezoelectric tip. For chemical detection, high surface-area selective absorbent materials are coated on the cantilever tip. Binding of the target antigens or analytes to the cantilever surface increases the cantilever mass. Detection of target antigens or analytes is achieved by monitoring the cantilever's resonance frequency and determining the resonance frequency shift that is due to the mass of the adsorbed target antigens on the cantilever surface. The use of a piezoelectric unimorph cantilever allows both electrical actuation and electrical sensing. Incorporating a non-piezoelectric tip (14) enhances the sensitivity of the sensor. In addition, the piezoelectric cantilever can withstand damping in highly viscous liquids and can be used as a viscosity sensor in wide viscosity range.

  3. Interferometric fiber optic sensors.

    Science.gov (United States)

    Lee, Byeong Ha; Kim, Young Ho; Park, Kwan Seob; Eom, Joo Beom; Kim, Myoung Jin; Rho, Byung Sup; Choi, Hae Young

    2012-01-01

    Fiber optic interferometers to sense various physical parameters including temperature, strain, pressure, and refractive index have been widely investigated. They can be categorized into four types: Fabry-Perot, Mach-Zehnder, Michelson, and Sagnac. In this paper, each type of interferometric sensor is reviewed in terms of operating principles, fabrication methods, and application fields. Some specific examples of recently reported interferometeric sensor technologies are presented in detail to show their large potential in practical applications. Some of the simple to fabricate but exceedingly effective Fabry-Perot interferometers, implemented in both extrinsic and intrinsic structures, are discussed. Also, a wide variety of Mach-Zehnder and Michelson interferometric sensors based on photonic crystal fibers are introduced along with their remarkable sensing performances. Finally, the simultaneous multi-parameter sensing capability of a pair of long period fiber grating (LPG) is presented in two types of structures; one is the Mach-Zehnder interferometer formed in a double cladding fiber and the other is the highly sensitive Sagnac interferometer cascaded with an LPG pair.

  4. Interferometric Fiber Optic Sensors

    Directory of Open Access Journals (Sweden)

    Hae Young Choi

    2012-02-01

    Full Text Available Fiber optic interferometers to sense various physical parameters including temperature, strain, pressure, and refractive index have been widely investigated. They can be categorized into four types: Fabry-Perot, Mach-Zehnder, Michelson, and Sagnac. In this paper, each type of interferometric sensor is reviewed in terms of operating principles, fabrication methods, and application fields. Some specific examples of recently reported interferometeric sensor technologies are presented in detail to show their large potential in practical applications. Some of the simple to fabricate but exceedingly effective Fabry-Perot interferometers, implemented in both extrinsic and intrinsic structures, are discussed. Also, a wide variety of Mach-Zehnder and Michelson interferometric sensors based on photonic crystal fibers are introduced along with their remarkable sensing performances. Finally, the simultaneous multi-parameter sensing capability of a pair of long period fiber grating (LPG is presented in two types of structures; one is the Mach-Zehnder interferometer formed in a double cladding fiber and the other is the highly sensitive Sagnac interferometer cascaded with an LPG pair.

  5. Sobre el error como acontecimiento y el hacking como aprovechamiento creativo del mismo

    OpenAIRE

    Aceros Gualdrón, Juan Carlos

    2004-01-01

    Desde una mirada renovada del poder, que empieza con los trabajos de Michel Foucault, esta ponencia es una reflexión sobre el componente ético-político del hacking.En este sentido se exponen como marco de referencia los conceptos de poder, libertad y técnicas de gobierno, para luego, desde allí, hacer un análisis de la manera como los hackers realizan una búsqueda del error, con el fin de aprovecharlo creativamente en la consecución de determinados objetivos (acceso no autorizado a cierta inf...

  6. Hydra Rendezvous and Docking Sensor

    Science.gov (United States)

    Roe, Fred; Carrington, Connie

    2007-01-01

    The U.S. technology to support a CEV AR&D activity is mature and was developed by NASA and supporting industry during an extensive research and development program conducted during the 1990's and early 2000 time frame at the Marshall Space Flight Center. Development and demonstration of a rendezvous/docking sensor was identified early in the AR&D Program as the critical enabling technology that allows automated proxinity operations and docking. A first generation rendezvous/docking sensor, the Video Guidance Sensor (VGS) was developed and successfully flown on STS 87 and again on STS 95, proving the concept of a video-based sensor. Advances in both video and signal processing technologies and the lessons learned from the two successful flight experiments provided a baseline for the development of a new generation of video based rendezvous/docking sensor. The Advanced Video Guidance Sensor (AVGS) has greatly increased performance and additional capability for longer-range operation. A Demonstration Automatic Rendezvous Technology (DART) flight experiment was flown in April 2005 using AVGS as the primary proximity operations sensor. Because of the absence of a docking mechanism on the target satellite, this mission did not demonstrate the ability of the sensor to coltrold ocking. Mission results indicate that the rendezvous sensor operated successfully in "spot mode" (2 km acquisition of the target, bearing data only) but was never commanded to "acquire and track" the docking target. Parts obsolescence issues prevent the construction of current design AVGS units to support the NASA Exploration initiative. This flight proven AR&D technology is being modularized and upgraded with additional capabilities through the Hydra project at the Marshall Space Flight Center. Hydra brings a unique engineering approach and sensor architecture to the table, to solve the continuing issues of parts obsolescence and multiple sensor integration. This paper presents an approach to

  7. Ripeness sensor development

    Energy Technology Data Exchange (ETDEWEB)

    1992-11-01

    About 20--25% of the total production of fruits and vegetables in the USA must be discarded after harvest About 25--30% of this loss is the result of over-ripening and this loss represents about 8.39 [times] 10[sup 12] BTU of invested energy every year. This invested energy could be saved by non-destructive ripeness sensing. Sweetness is an important indicator of fruit quality and highly correlated with ripeness in most fruits. Research to develop a non-destructive fruit ripeness sensor has been conducted in the Agricultural Engineering Department at Purdue University. It is based on [sup 1]H-MR (proton Magnetic Resonance). A first generation prototype of the ripeness sensor based on [sup 1]H-MR was built and tested with. Results show that the sensor can discriminate small fruit (0.75 in diameter or smaller) differing in sugar content by 6%. This prototype can separate the fruit into at least two groups: one ripe and the other not ripe. The estimated cost for such a ripeness sensor is around $4,000. The signal sensitivity of the prototype can be improved to enable it to differentiate between fruits varying in sugar content by only 1 or 2% by using water peak suppression techniques to recover relatively weak sugar resonance signals in intact fruits, modifying circuits to eliminate noise, leakage and distortion of input/output signals, improving the magnetic console to get a higher magnetic field and better homogeneity, and designing a probe to achieve a higher signal-to-noise (S/N) ratio. As research continues a second generation ripeness sensor will be developed which will incorporate many of the improvements and which will be suitable for commercial use. Additional research will allow application of the technique to a wider range of fruit sizes (from blueberries to watermelons). This report describes estimated energy savings, feasibility studies, development of the initial prototype, and preliminary evaluation of the first generation prototype.

  8. Hail Monitor Sensor

    Science.gov (United States)

    Younquist, Robert; Haskell, William; Immer, Christopher; Cox, Bobby; Lane, John

    2009-01-01

    An inexpensive and simple hail monitor design has been developed that has a single piezoelectric ceramic disc and uses a metal plate as a sounding board. The structure is durable and able to withstand the launch environment. This design has several advantages over a multi-ceramic sensor, including reduced cost and complexity, increased durability, and improvement in impact response uniformity over the active surface. However, the most important characteristic of this design is the potential to use frequency discrimination between the spectrum created from raindrop impact and a hailstone impact. The sound of hail hitting a metal plate is distinctly different from the sound of rain hitting the same plate. This fortuitous behavior of the pyramid sensor may lead to a signal processing strategy, which is inherently more reliable than one depending on amplitude processing only. The initial concept has been im proved by forming a shallow pyramid structure so that hail is encouraged to bounce away from the sensor so as not to be counted more than once. The sloped surface also discourages water from collecting. Additionally, the final prototype version includes a mounting box for the piezo-ceramic, which is offset from the pyramid apex, thus helping to reduce non-uniform response (see Figure 2). The frequency spectra from a single raindrop impact and a single ice ball impact have been compared. The most notable feature of the frequency resonant peaks is the ratio of the 5.2 kHz to 3.1 kHz components. In the case of a raindrop, this ratio is very small. But in the case of an ice ball, the ratio is roughly one third. This frequency signature of ice balls should provide a robust method for discriminating raindrops from hailstones. Considering that hail size distributions (HSDs) and fall rates are roughly 1 percent that of rainfall, hailstone sizes range from a few tenths of a centimeter to several centimeters. There may be considerable size overlap between large rain and small

  9. Garment-Integrated Bend Sensor

    Directory of Open Access Journals (Sweden)

    Guido Gioberto

    2014-09-01

    Full Text Available Garment-integrated sensors equip clothes with a smart sensing capability, while preserving the comfort of the user. However, this benefit can be to the detriment of sensing accuracy due to the unpredictability of garment movement (which affects sensor positioning and textile folds (which can affect sensor orientation. However, sensors integrated directly into garments or fabric structures can also be used to detect the movement of the garment during wearing. Specifically, a textile bend sensor could be used to sense folds in the garment. We tested a garment-integrated stitched sensor for five types of folds, stitched on five different weights of un-stretchable denim fabric and analyzed the effects of fold complexity and fabric stiffness, under un-insulated and insulated conditions. Results show that insulation improves the linearity and repeatability of the sensor response, particularly for higher fold complexity. Stiffer fabrics show greater sensitivity, but less linearity. Sensor response amplitude is larger for more complex fold geometries. The utility of a linear bending response (insulated and a binary shorting response (un-insulated is discussed. Overall, the sensor exhibits excellent repeatability and accuracy, particularly for a fiber-based, textile-integrated sensor.

  10. Sensor integration in radioactive environments

    Science.gov (United States)

    Harfensteller, Mark; Schilp, Michael; Eursch, Andreas; Zaeh, Michael F.

    2004-12-01

    Radioactive material of high activity levels has to be handled in a nuclear medicine environment. Until now most of these activities are done manually or by rudimentally automated processes. To increase radiation safety and process quality, smart automation strategies for these processes have to be developed. Especially long-term processes with radioactive materials have to be automated in early stages of development. This leads to a certain flexibility regarding requirements demanding an adjustable automation concept. The application of radiation hardened sensors is expensive but even these sensors will be destroyed by radiation effects. To allow therefore standard sensors to be used in radioactive environments, different strategies have been tested: In general, the sensors must be applied in a way to allow an easy access to sensors for replacement purposes. But this approach might not be sophisticated. An additional solution is the reduction of exposure of sensitive parts such as electronics. This means dividing the sensor in a measuring part which is placed in the radioactive environment and in a sensitive, shielded control part as it is realized by fibre optic sensors. The implementation of these approaches is demonstrated in sensor applications for radium handling systems e. g. contactless control of the needle clearance of a dispensing system via a fibre optic sensor. Further scenarios for sensor integration problems are presented in this paper.

  11. A microfabricated amperometric moisture sensor.

    Science.gov (United States)

    Su, Xiao-Li; Xingguo, Xiong; Dallas, Tim; Gangopadhyay, Shubhra; Temkin, Henryk; Wang, Xuejun; Walulu, Richard; Li, Jianzhong; Dasgupta, Purnendu K

    2002-02-11

    We describe a microfabricated moisture sensor with interdigitated Au or Pt electrodes on a silicon substrate. The sensor active area is covered with a spin-coated, baked-on layer of Nafion(R) perfluorosulfonate ionomer of submicron thickness. The sensor responds to moisture with a 10-90% rise time of 50-100 ms and a 90-10% fall time of 20-30 ms, faster than any other presently available sensor. The logarithm of the sensor current is related to the cube root of the moisture level at a given temperature. At 23 degrees C, the sensor easily measures relative humidities as low as 10%. The sensor response at a given absolute humidity level decreases exponentially with increasing temperature. The film is stable up to a temperature of 150 degrees C, permitting elevated temperature moisture measurement. Since sorbed water is actively decomposed electrolytically, the sensors exhibit negligible hysteresis. Response reproducibility of an individual sensor is <1%, that between identically made sensors is <5%, suggesting mass production techniques without individual calibration will be acceptable for all but the most demanding situation.

  12. La digitalizacion como ecologizacion y agilizacion de los procedimientos administrativos

    National Research Council Canada - National Science Library

    Hoyos Ramirez, Luis Miguel

    2011-01-01

    ...: primero, como una de las formas mas eficaces de hacer que el funcionamiento de la administracion sea mas ecologico y racional en el uso de los recursos naturales, y segundo, poner de relieve como...

  13. Las javieradas como caso de estudio

    Directory of Open Access Journals (Sweden)

    Mª Cruz Porcal Gonzalo

    2006-01-01

    Full Text Available A pesar de su todavía modesta participación en la economía y en el empleo regional, el turismo en Navarra ha mostrado durante los últimos años un significativo dinamismo tal y como, por ejemplo, lo testimonia el incremento del número de visitantes y de las empresas turísticas. Favorecido por una serie de circunstancias de índole variada, este desarrollo turístico se sustenta en una gran diversidad geográfica y cultural patente en los paisajes, el arte, las fiestas, la gastronomía, etc. Pero Navarra es, a su vez, una región que secularmente ha otorgado un gran peso a la tradición y a las creencias religiosas. En este contexto, algunas de las numerosas acciones emprendidas por la administración regional para dinamizar el sector turístico se han encaminado a revalorizar dos importantes legados culturales: el castillo de Javier y el Camino de Santiago. Se aprecia que ambos se hallan estrechamente relacionados con el turismo cultural, el turismo religioso y las peregrinaciones, unos fenómenos que hunden sus raíces en tiempos pasados pero que continúan teniendo en la actualidad una indudable relevancia a escala mundial. La intención primordial del presente trabajo es analizar el turismo de peregrinaciones en Navarra, más concretamente, el que tiene como destino del viaje la cuna de San Francisco Javier. Con dicho afán, se realiza una reflexión conceptual previa y un breve repaso de las fiestas y tradiciones religiosas que forman parte del patrimonio cultural intangible de Navarra, haciendo particular hincapié en las romerías y en el Camino de Santiago. Al hilo de ello, se afronta, a continuación, el estudio de la peregrinación más singular y populosa de Navarra: la Javierada. Su origen, sus principales rasgos, el perfil y las motivaciones de los peregrinos, los caracteres e hitos más importantes del recorrido, las peculiaridades del destino —entendido como lugar sagrado y espacio turístico— constituyen las principales

  14. Arquitectura como percepción

    Directory of Open Access Journals (Sweden)

    Mañana Borrazás, Patricia

    2003-12-01

    Full Text Available This text sets out to illustrate types of basic analysis in researching a question as intrinsically human as perception. In the analysis of a construction, the aspects relative to perception allow us to access interesting information as to how a construction functions and what is implied by its different spaces, information which is in direct relation to more human, living aspects of architecture. These analyses complement formal analyses, as while these allow us to describe a construction in time and space, analyses of perception seek to stress the existing relationship between the human being and the construction, understanding architecture as a physical element to be experienced and which has been constructed to create a favourable atmosphere for certain perceptions. The study first shows the most basic elements in perception analysis and how these support a methodology that attempts to understand a construction in all its aspects (formal, social, symbolic, giving as an example a Neolithic Galician burial mound.Este texto trata de ilustrar los tipos de análisis básicos para investigar una cuestión tan intrínsecamente humana como la percepción. En el análisis de una construcción, los aspectos relativos a la percepción nos permiten acceder a una interesante información de cómo una construcción funciona y qué implican sus distintos espacios, información en directa relación con los aspectos más humanos y vivenciales de la arquitectura. Son unos análisis complementarios a los análisis formales, ya que mientras estos nos permiten describir en el espacio y en el tiempo una construcción, los análisis de percepción tratan de incidir en la relación existente entre el ser humano y la construcción, entendiendo a la arquitectura también como elemento físico a experimentar y que ha sido construido para propiciar ciertas percepciones. Se exponen en primer lugar las claves más básicas de los análisis de percepción y cómo estos se

  15. REPENSANDO LA CRISIS COMO CONCRECIÓN CONCEPTUAL

    Directory of Open Access Journals (Sweden)

    Mario González Arencibia

    2006-07-01

    Full Text Available El ensayo pretende contribuir a la reflexión sobre la crisis como concreción conceptual desde el enfoque marxista. Desde el punto de vista metodológico, asume como aspecto central a la crisis como el resultado de múltiples manifestaciones, siendo un proceso de determinaciones, que contiene una relación de causa y efecto, que abarca esta como un todo único y de manera dialéctica.

  16. Como seria a Terra sem a lua?

    OpenAIRE

    Estevinho, Adriana Patrícia Gonçalves; Mesquita, Elisabete da Conceição Afonso; Minhoto, Paula Maria Lino Veigas

    2012-01-01

    A vida que existe na Terra resulta de um conjunto de circunstâncias muito particulares e raras nas quais se inclui a presença da Lua. A Lua é o satélite natural da Terra e os dois planetas influenciam-se mutuamente. Apesar de ser um pequeno planeta a Lua é responsável por vários fenómenos terrestres como as marés que afetam a velocidade de rotação da Terra. O seu afastamento, apesar de lento é constante e provocará alterações nas condições do planeta que permitem sustentar a vi...

  17. El fujiforismo como forma de gobierno

    Directory of Open Access Journals (Sweden)

    Heraclio Bonilla

    2000-01-01

    Full Text Available El Perú, una vez más, se ha convertido en las últimas semanas en el centro de la curiosidad internacional. Como en anteriores oportunidades, no precisamente por las mejores razones. Desde el pasado mes de junio, en efecto, ese país ha sido el escenario de una serie de peripecias que despiertan sentimientos mezclados de asombro y de bochorno. Los acontecimientos más saltantes de esa zaga fueron la convocatoria a elecciones generales, y en las cuales uno de los candidatos era el Ing. Alberto Fujimori, presidente en ejercicio del Perú y cuya discutible candidatura por tercera vez fue posible por una no menos discutible interpretación de la ley por parte de una mayoría adicta en el Congreso de la República.

  18. Hume: a teoria social como sistema

    Directory of Open Access Journals (Sweden)

    Rolf Kuntz

    2011-12-01

    Full Text Available Hume defende na Investigação sobre o Entendimento Humano a parcimônia no uso de princípios explicativos. Tenta-se mostrar, neste artigo, como ele procurou seguir essa diretriz em seus trabalhos sobre os sentimentos morais, a história, a política e a economia. Explora-se, ao mesmo tempo, o caráter sistemático do projeto enunciado no começo do Tratado da Natureza Humana.In his Enquiry on Human Understanding Hume proposes a rule of parcimony in the use of explanatory principles. This essay is an attempt to show how the philosopher managed to follow that rule in his writings on moral sentiments, history, politics and economics. At the same time, it explores the systematic character of the project described in the presentation of the Treatise on Human Nature.

  19. La cultura como verdad: pobreza latinoamericana

    Directory of Open Access Journals (Sweden)

    Ana María Rocchietti

    2000-04-01

    Full Text Available El artículo parte de un balance crítico de la obra Antropología de la Pobreza, del antropólogo Oscar Lewis para analizar el concepto de pobreza en América Latina. Se argumenta que la cultura de la pobreza ofrece la posibilidad de incluir a las formaciones simbólicas de las tradiciones vivientes y a las que emergen en la existencia comunitaria de los pobres como un factor de peso en la evolución de las relaciones de fuerza entre las clases subalternas y las clases dominantes; entre los sectores populares rurales y urbanos y los gobiernos; entre las formaciones sociales nacionales y el imperialismo.

  20. LA CULTURA COMO VERDAD: POBREZA LATINOAMERICANA

    Directory of Open Access Journals (Sweden)

    Ana María Rocchietti

    2000-01-01

    Full Text Available El artículo parte de un balance crítico de la obra Antropología de la Pobreza, del antropólogo Oscar Lewis para analizar el concepto de pobreza en América Latina. Se argumenta que la cultura de la pobreza ofrece la posibilidad de incluir a las formaciones simbólicas de las tradiciones vivientes y a las que emergen en la existencia comunitaria de los pobres como un factor de peso en la evolución de las relaciones de fuerza entre las clases subalternas y las clases dominantes; entre los sectores populares rurales y urbanos y los gobiernos; entre las formaciones sociales nacionales y el imperialismo.

  1. COMO FAZER A DANÇAPRÓPRIA?

    OpenAIRE

    Busaid, Ana Milena Navarro

    2012-01-01

    Este texto tem o fim de esboçar os temas abordados por André Lepecki na introdução do livro: “Agotar la danza: Performance y Politica del movimento” e, ao mesmo tempo, fazer cruzamentos com ideias que desenvolvo em minha pesquisa sobre processos de criação em dança. Analisarei temas relevantes para minha pesquisa, como a ontologia do movimento na dança e sua hegemonia, e os processos de subjetivação do sujeito no fazer artístico. O objetivo é apontar para a construção de uma dança pr...

  2. El "Clientelismo" politico como material novelable

    Directory of Open Access Journals (Sweden)

    Cesar de Vicente Hernando

    2002-12-01

    Full Text Available Lo que instituye el "realismo" en los aproximadamente cien años que median entre la "revolución" burguesa de 1868 ("la Gloriosa" y la ruptura estética de los años sesenta ya en el siglo XX es precisamente lo que definió (y subyace a su producción novelística Benito Peréz Galdós con el título de "La sociedad presente como materia novelable", discurso leído ante la Real Academia Española, con motivo de su recepción en 1897. Este texto es una justificación teórica de lo que viene a ser la inscripción en la literatura de las lunchas y transformaciones ideológicas que la burguesía establece.

  3. Como Perseu se defendeu de Medusa?

    Directory of Open Access Journals (Sweden)

    Rose Lumertz de Freitas

    2012-04-01

    Full Text Available Na psicanálise francesa, principalmente com Lacan, o conceito de falta passou a ser de grande importância. Ao que, então, perguntamos: o que é a falta? E quando esta falta? O que acontece? O que acontece quando o não especularizável não está excluído, se fazendo, assim, especular? Quando Perseu vai ao encontro de Medusa, guiando-se por sua imagem refletida em um espelho de bronze polido, segurado por Atena, como pôde este herói defender-se de Medusa? Qual foi a forma encontrada por ele para se defender da presença do objeto que introduz a dimensão do real nu?

  4. O humor como quebra da convencionalidade

    Directory of Open Access Journals (Sweden)

    Stella E. O. Tagnin

    2005-01-01

    Full Text Available Este artigo trata da relação entre a convencionalidade na língua e o humor. Para tanto, apresenta uma categorização de combinações consagradas, desde colocações a fórmulas discursivas, e discute como se prestam à criação do humor. Na qualidade de categorias convencionais, são combinações fixas ou semifixas "prontas para o uso" e decodificadas como um todo. O humor aqui apresentado é lingüístico e obtido pela manipulação/literalização dessas combinações, quebrando a expectativa do ouvinte/leitor. A estreita associação entre o domínio da convencionalidade e a fluência numa língua leva à não compreensão do humor pelo falante não fluente.This article discusses the relationship between conventionality in language and humor. It puts forward a categorization of ready-made combinations, from collocations to discourse formulas, highlighting the mechanisms in which they are used to create humor. As ready-made combinations, they are fixed or semi-fixed expressions decoded as a linguistic whole. Humor is achieved by manipulating these combinations so as to cause a breach in the listener's/reader's expectations. Because mastery of linguistic conventionality is closely associated with fluency, and humor relies highly on a breach of conventionality, it is claimed that lack of fluency prevents full comprehension of humor.

  5. O PRODUTO COMO CAUSADOR DE ACIDENTES

    Directory of Open Access Journals (Sweden)

    Widomar Carpes Jr

    2004-06-01

    Full Text Available Neste artigo analisa-se a contribuição dos produtos para a geração de acidentes, apresentando-se estatísticas de acidentes de trabalho, de trânsito e aeronáuticos. Além disso, para melhor ilustrar a relação entre produtos e a ocorrência de acidentes, alguns casos de acidentes ocorridos e divulgados pela mídia são comentados. As estatísticas e os casos comentados demonstram a importância do estudo dos acidentes envolvendo produtos, evidenciando que praticamente todos os acidentes estão relacionados com o uso de produtos industrializados. Então, se analisa histórica e criticamente as principais teorias de acidentes de trabalho, porque são as únicas teorias existentes em relação aos acidentes. Além delas, são analisados os diversos conceitos sobre o erro humano e sua ocorrência, pois estes são apontados como grandes causadores de acidentes. Nesta análise, se observa que os acidentes estão mais relacionados aos perigos ou às características perigosas dos produtos do que às atitudes e ao comportamento do usuário. Faz-se uma revisão dos conceitos associados aos acidentes, tais como perigo, risco, acidente e dano, a partir dos quais apresenta-se um fluxograma contendo os elementos necessários para a manifestação dos acidentes. Ao final, conclui-se que a participação dos produtos na ocorrência de acidentes é evidente e que o comportamento do usuário é dependente das características do produto e da situação na qual ele é utilizado.

  6. El desarrollo organizacional como facilitador del cambio

    Directory of Open Access Journals (Sweden)

    Henry Molina

    2000-01-01

    Full Text Available El Desarrollo Organizacional (DO ha surgido de las exigencias de un ambiente cambiante y del conocimiento originado por la evolución de las ciencias sociales aplicadas. Los cambios rápidos dentro del entorno organizacional han exigido procesos y estructuras organizacionales que sean mucho más flexibles y que brinden mayor capacidad de respuesta que las estructuras tradicionales. Se requieren nuevas capacidades individuales y organizacionales que puedan impulsar las iniciativas individuales y la disposición para asumir riesgos. Igualmente, debemos considerar que existen marcadas diferencias entre las características individuales de los gerentes, las características individuales de los profesionales del desarrollo organizacional, sus habilidades y conocimientos y los estilos de las intervenciones del desarrollo organizacional. Tbdas estas diferencias hacen que sea virtualmente imposible predecir con precisión el curso y los resultados de las intervenciones en las organizaciones cliente. En este documento presento un resumen de lecturas acerca del desarrollo organizacional como facilitador del cambio; y expongo un marco de referencia para la comprensión de los factores determinantes de la relación entre las intervenciones del DO y los cambios organizacionales con el fin de mejorar la predictabilidad y la efectividad de los esfuerzos de cambio de sus intervenciones. El propósito central de este documento es dotar a los agentes de cambio de conocimiento y herramientas para que comprendan las características del cambio, los métodos de aprendizaje tanto de las organizaciones como de la gente y de cómo los agentes de cambio deben diseñar sus intervenciones y posteriormente mejorar los resultados de las mismas

  7. Taxonomia como elemento estruturante em portais corporativos

    Directory of Open Access Journals (Sweden)

    Luciane Paula Vital

    2012-01-01

    Full Text Available Este trabalho busca discutir os objetivos e requisitos necessários a um portal corporativo e de que forma a construção de uma taxonomia possibilita atingi-los, configurando-se em um modelo de representação da informação e do conhecimento nesse contexto. Apresenta a evolução das intranets em direção aos portais, construindo um ponto de acesso comum as informações organizacionais. Apresenta uma revisão sobre as funcionalidades que um portal corporativo deve apresentar. Conceitua e caracteriza os diferentes tipos de taxonomia e a forma com que organiza e representa a informação. Por fim, apresenta a taxonomia como ferramenta para a determinação de categorias conceituais e de relacionamentos semânticos de uma área, assim como, da estrutura navegacional, permitindo qualificar o processo de recuperação da informação. Palavras-chave Taxonomia. Portais Corporativos. Representação da Informação. Organização da Informação. Abstract This article discusses the objectives and requirements necessary for a corporate portal and how to build a taxonomy allows for to reach them, becoming a model of representation information and knowledge in this context. Shows the evolution of intranets into the portal, building a common access point to information organizational. Presents an overview of the features that an enterprise portal should present. Conceptualizes and describes the different types of taxonomy and the way it organizes and represents information. Finally, the taxonomy as a tool for determining the conceptual categories and semantic relationships of an area, as well as the navigational structure, allowing the process to qualify for retrieval. Keywords Taxonomy. Enterprise Portal. Information Representation. Information Organization.

  8. Improvement of glassy sol-gel sensors for preventive conservation of historical materials against acidity

    Directory of Open Access Journals (Sweden)

    Carmona, N.

    2007-08-01

    Full Text Available Sensors based on sol-gel glassy coatings doped with 2[4-(dimethyl-amino phenylazo] benzoic acid are able to change their optical absorption when they are submitted to different concentration of H3O+ and OH-. The sensors behaviour in field tests was studied in Cracow (Poland, varying the normal procedure of operation to improve their response. Both the sensors optical parameters and the environmental conditions (temperature, humidity, pressure, SO2 and NOx concentrations were measured. The sensors response was analysed in terms of their visible absorbance changes, which are due to local neutralisation reactions in the sensors surface by the join effect of acid pollutants and humidity. Correlations between the main acid pollutant (SO2 concentration and the sensors response are established to provide a relation between the optical absorption and the environmental pH. The sensors are able to detect and monitorise environmental acidity, as well as to alert on the pollutant concentration that may damage most of the historical materials.

    Los sensores a base de recubrimientos vítreos sol-gel dopados con ácido 2[4-(dimetil-amino fenilazo] benzoico son capaces de cambiar su absorción óptica cuando se someten a distintas concentraciones de iones H3O+ y OH-. La respuesta de los sensores en ensayos de campo se estudió en Cracovia (Polonia variando el procedimiento normal de uso, con el fin de mejorar su respuesta. Se midieron tanto los parámetros ópticos de los sensores como las condiciones ambientales (temperatura, humedad, presión y concentraciones de SO2 y de NOx. La respuesta de los sensores se analizó en términos de los cambios de su absorción visible. Dichos cambios se deben a reacciones locales de neutralización que tienen lugar en la superficie de los sensores, debido al efecto conjunto de los contaminantes de carácter ácido y a la humedad ambiental. Se establecieron correlaciones entre la concentración del contaminante

  9. Piezocomposites metal-cerámica como elementos activos en acelerómetros

    Directory of Open Access Journals (Sweden)

    Ochoa, P.

    2002-02-01

    Full Text Available Piezoelectric ceramic materials have an important number of applications that is continuing increasing. One of these applications is as driving element in the design of an accelerometer. They may be used in monitoring vibration for the automobile and aeroespacial industries and robotic or civil engineering. The cymbal transducer is a good candidate for accelerometer applications due to its high effective piezoelectric charge coefficients. In this work it is shown that changes in the geometry and size of the caps improve the performance of the sensor. The sensitivity of the cymbal accelerometer increases with decreasing cap size. The mechanical vibration response of the cymbal is studied and different properties, like resonant frequency, electromechanical coupling coefficient, and fastest response time are compared.

    Los materiales cerámicos piezoeléctricos presentan un número importante y en continuo aumento de aplicaciones. Entre éstas su utilización como elementos activos en el diseño de acelerómetros posibilita el control de vibraciones en la industria del transporte, aerospacial, robótica e ingeniería civil entre otras. Entre los múltiples diseños como material compuesto destaca, gracias a sus elevados coeficientes de carga efectivos, el denominado tipo címbalo. En este trabajo se comprueba que modificando la geometría y el tamaño de las cápsulas se optimiza el comportamiento del sensor. Concretamente una disminución en el tamaño de las cápsulas se traduce en un aumento de la sensibilidad del acelerómetro. También se muestran los espectros de impedancia y se comparan distintas propiedades como son la frecuencia de resonancia, coeficiente de acoplo electromecánico y tiempo mínimo de respuesta.

  10. An ontology for sensor networks

    Science.gov (United States)

    Compton, Michael; Neuhaus, Holger; Bermudez, Luis; Cox, Simon

    2010-05-01

    Sensors and networks of sensors are important ways of monitoring and digitizing reality. As the number and size of sensor networks grows, so too does the amount of data collected. Users of such networks typically need to discover the sensors and data that fit their needs without necessarily understanding the complexities of the network itself. The burden on users is eased if the network and its data are expressed in terms of concepts familiar to the users and their job functions, rather than in terms of the network or how it was designed. Furthermore, the task of collecting and combining data from multiple sensor networks is made easier if metadata about the data and the networks is stored in a format and conceptual models that is amenable to machine reasoning and inference. While the OGC's (Open Geospatial Consortium) SWE (Sensor Web Enablement) standards provide for the description and access to data and metadata for sensors, they do not provide facilities for abstraction, categorization, and reasoning consistent with standard technologies. Once sensors and networks are described using rich semantics (that is, by using logic to describe the sensors, the domain of interest, and the measurements) then reasoning and classification can be used to analyse and categorise data, relate measurements with similar information content, and manage, query and task sensors. This will enable types of automated processing and logical assurance built on OGC standards. The W3C SSN-XG (Semantic Sensor Networks Incubator Group) is producing a generic ontology to describe sensors, their environment and the measurements they make. The ontology provides definitions for the structure of sensors and observations, leaving the details of the observed domain unspecified. This allows abstract representations of real world entities, which are not observed directly but through their observable qualities. Domain semantics, units of measurement, time and time series, and location and mobility

  11. A Piezoelectric Shear Stress Sensor

    Science.gov (United States)

    Kim, Taeyang; Saini, Aditya; Kim, Jinwook; Gopalarathnam, Ashok; Zhu, Yong; Palmieri, Frank L.; Wohl, Christopher J.; Jiang, Xiaoning

    2016-01-01

    In this paper, a piezoelectric sensor with a floating element was developed for shear stress measurement. The piezoelectric sensor was designed to detect the pure shear stress suppressing effects of normal stress generated from the vortex lift-up by applying opposite poling vectors to the: piezoelectric elements. The sensor was first calibrated in the lab by applying shear forces and it showed high sensitivity to shear stress (=91.3 +/- 2.1 pC/Pa) due to the high piezoelectric coefficients of PMN-33%PT (d31=-1330 pC/N). The sensor also showed almost no sensitivity to normal stress (less than 1.2 pC/Pa) because of the electromechanical symmetry of the device. The usable frequency range of the sensor is 0-800 Hz. Keywords: Piezoelectric sensor, shear stress, floating element, electromechanical symmetry

  12. Low-noise Magnetic Sensors

    KAUST Repository

    Kosel, Jurgen

    2014-03-27

    Magnetic sensors are disclosed, as well as methods for fabricating and using the same. In some embodiments, an EMR effect sensor includes a semiconductor layer. In some embodiments, the EMR effect sensor may include a conductive layer substantially coupled to the semiconductor layer. In some embodiments, the EMR effect sensor may include a voltage lead coupled to the conductive layer. In some embodiments, the voltage lead may be configured to provide a voltage for measurement by a voltage measurement circuit. In some embodiments, the EMR effect sensor may include a second voltage lead coupled to the semiconductor layer. In some embodiments, the second voltage lead may be configured to provide a voltage for measurement by a voltage measurement circuit. Embodiments of a Hall effect sensor having the same or similar structure are also disclosed.

  13. -Net Approach to Sensor -Coverage

    Directory of Open Access Journals (Sweden)

    Fusco Giordano

    2010-01-01

    Full Text Available Wireless sensors rely on battery power, and in many applications it is difficult or prohibitive to replace them. Hence, in order to prolongate the system's lifetime, some sensors can be kept inactive while others perform all the tasks. In this paper, we study the -coverage problem of activating the minimum number of sensors to ensure that every point in the area is covered by at least sensors. This ensures higher fault tolerance, robustness, and improves many operations, among which position detection and intrusion detection. The -coverage problem is trivially NP-complete, and hence we can only provide approximation algorithms. In this paper, we present an algorithm based on an extension of the classical -net technique. This method gives an -approximation, where is the number of sensors in an optimal solution. We do not make any particular assumption on the shape of the areas covered by each sensor, besides that they must be closed, connected, and without holes.

  14. Sensor Compendium - A Snowmass Whitepaper-

    Energy Technology Data Exchange (ETDEWEB)

    Artuso, M. [Syracuse Univ., NY (United States); Battaglia, M. [Univ. of California, Santa Cruz, CA (United States); Bolla, G. [Purdue Univ., West Lafayette, IN (United States); Bortoletto, D. [Purdue Univ., West Lafayette, IN (United States); Caberera, B. [Stanford Univ., CA (United States); Carlstrom, J E [Univ. of Chicago, IL (United States); Argonne National Lab. (ANL), Argonne, IL (United States); Chang, C. L. [Univ. of Chicago, IL (United States); Argonne National Lab. (ANL), Argonne, IL (United States); Cooper, W. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Da Via, C. [Univ. of Manchester (United Kingdom); Demarteau, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Fast, J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Frisch, H. [Univ. of Chicago, IL (United States), et al.

    2013-10-01

    Sensors play a key role in detecting both charged particles and photons for all three frontiers in Particle Physics. The signals from an individual sensor that can be used include ionization deposited, phonons created, or light emitted from excitations of the material. The individual sensors are then typically arrayed for detection of individual particles or groups of particles. Mounting of new, ever higher performance experiments, often depend on advances in sensors in a range of performance characteristics. These performance metrics can include position resolution for passing particles, time resolution on particles impacting the sensor, and overall rate capabilities. In addition the feasible detector area and cost frequently provides a limit to what can be built and therefore is often another area where improvements are important. Finally, radiation tolerance is becoming a requirement in a broad array of devices. We present a status report on a broad category of sensors, including challenges for the future and work in progress to solve those challenges.

  15. Engineering Genetically Encoded FRET Sensors

    Science.gov (United States)

    Lindenburg, Laurens; Merkx, Maarten

    2014-01-01

    Förster Resonance Energy Transfer (FRET) between two fluorescent proteins can be exploited to create fully genetically encoded and thus subcellularly targetable sensors. FRET sensors report changes in energy transfer between a donor and an acceptor fluorescent protein that occur when an attached sensor domain undergoes a change in conformation in response to ligand binding. The design of sensitive FRET sensors remains challenging as there are few generally applicable design rules and each sensor must be optimized anew. In this review we discuss various strategies that address this shortcoming, including rational design approaches that exploit self-associating fluorescent domains and the directed evolution of FRET sensors using high-throughput screening. PMID:24991940

  16. Micro-Mechanical Temperature Sensors

    DEFF Research Database (Denmark)

    Larsen, Tom

    Temperature is the most frequently measured physical quantity in the world. The field of thermometry is therefore constantly evolving towards better temperature sensors and better temperature measurements. The aim of this Ph.D. project was to improve an existing type of micro-mechanical temperature...... sensor or to develop a new one. Two types of micro-mechanical temperature sensors have been studied: Bilayer cantilevers and string-like beam resonators. Both sensor types utilize thermally generated stress. Bilayer cantilevers are frequently used as temperature sensors at the micro-scale, and the goal....... The reduced sensitivity was due to initial bending of the cantilevers and poor adhesion between the two cantilever materials. No further attempts were made to improve the sensitivity of bilayer cantilevers. The concept of using string-like resonators as temperature sensors has, for the first time, been...

  17. Metal-clad waveguide sensors

    DEFF Research Database (Denmark)

    Skivesen, Nina

    This work concerns planar optical waveguide sensors for biosensing applications, with the focus on deep-probe sensing for micron-scale biological objects like bacteria and whole cells. In the last two decades planar metal-clad waveguides have been brieflyintroduced in the literature applied...... for various biosensing applications, however a thorough study of the sensor configurations has not been presented, but is the main subject of this thesis. Optical sensors are generally well suited for bio-sensing asthey show high sensitivity and give an immediate response for minute changes in the refractive...... index of a sample, due to the high sensitivity of optical bio-sensors detection of non-labeled biological objects can be performed. The majority of opticalsensors presented in the literature and commercially available optical sensors are based on evanescent wave sensing, however most of these sensors...

  18. Airborne Sensor Thermal Management Solution

    Energy Technology Data Exchange (ETDEWEB)

    Ng, K. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-06-03

    The customer wants to outfit aircraft (de Havilland Twin Otter) with optical sensors. In previous product generations the sensor line-of-sight direction was fixed – the sensor’s direction relied on the orientation of the aircraft. The next generation sensor will be packaged in a rotatable turret so that the line-of-sight is reasonably independent of the aircraft’s orientation. This turret will be mounted on a boom protruding from the side of the aircraft. The customer wants to outfit aircraft (de Havilland Twin Otter) with optical sensors. In previous product generations the sensor line-of-sight direction was fixed – the sensor’s direction relied on the orientation of the aircraft. The next generation sensor will be packaged in a rotatable turret so that the line-of-sight is reasonably independent of the aircraft’s orientation. This turret will be mounted on a boom protruding from the side of the aircraft.

  19. Como reescribir funciones aleatorias multivariadas como univariadas para hacer cokrigeage. La teoría

    Directory of Open Access Journals (Sweden)

    Adrian Martínez-Vargas

    2010-03-01

    Full Text Available En el año 2005 Martínez-Vargas formuló un sistema de cokrigeage puro heterotópico para estimar una función aleatoria regionalizada (RF Z*(x definida como la combinación lineal de n RF's univariadas Zi(x, cuyos coeficientes 1i(x son indicatrices de un set disyuntivo de categorías i. Aparentemente este modelo se contradice pues asume que las covarianzas cruzadas existen en un mismo punto, a pesar de su carácter puramente heterotópico. Para evadir dicha contradicción se redefinió el set de RF Zi(x como una única RF Z(x,i, siendo los puntos (x,i y (x,j no coincidentes si i y j no son iguales. La heterotopía fue simplemente considerada como una omisión de la RF Z(x,. en los datos y en los puntos a estimar, no impuesta por el modelo; entonces el resultado es simplemente un caso particular del cokrigeage clásico. Con esta notación se reescribió el sistema de cokrigeage clásico como el sistema de krigeage de la RF univariada Z(x,i, asumiendo que esta posee un drift definido como m(x,i,j, donde los miembros fl(x,i,j de m(x,i,j pueden ser linealmente dependientes o independientes. Bajo esta notación el sistema de krigeage se reduce a un sistema univariado, la existencia de más de una variable o la presencia de heterotropía no impone la necesidad de manipulaciones extras para definir el sistema de ecuaciones de krigeage, incrementándose la eficiencia computacional.

  20. MEMS Bragg grating force sensor

    DEFF Research Database (Denmark)

    Reck, Kasper; Thomsen, Erik Vilain; Hansen, Ole

    2011-01-01

    We present modeling, design, fabrication and characterization of a new type of all-optical frequency modulated MEMS force sensor based on a mechanically amplified double clamped waveguide beam structure with integrated Bragg grating. The sensor is ideally suited for force measurements in harsh...... environments and for remote and distributed sensing and has a measured sensitivity of -14 nm/N, which is several times higher than what is obtained in conventional fiber Bragg grating force sensors. © 2011 Optical Society of America....

  1. Advances on Optical Fiber Sensors

    Directory of Open Access Journals (Sweden)

    Luciano Mescia

    2013-12-01

    Full Text Available In this review paper some recent advances on optical fiber sensors are reported. In particular, fiber Bragg grating (FBG, long period gratings (LPGs, evanescent field and hollow core optical fiber sensors are mentioned. Examples of recent optical fiber sensors for the measurement of strain, temperature, displacement, air flow, pressure, liquid-level, magnetic field, and the determination of methadone, hydrocarbons, ethanol, and sucrose are briefly described.

  2. Carbon Nanostructure-Based Sensors

    OpenAIRE

    Sarkar, Tapan

    2012-01-01

    One-dimensional (1-D) nanostructure-based sensors provide better sensitivity as compared to conventional thin film-based sensors due to their comparable dimensions with respect to Debye length. Single-walled carbon nanotubes (SWNTs) are 1-D nanostructures having high electrical mobility, high mechanical strength and high specific surface area that facilitate building of low-power, ultrahigh density sensors within limited space. However, pristine SWNTs posses limited sensitivity and selectivit...

  3. Generating three-parameter sensor

    Directory of Open Access Journals (Sweden)

    Filinyuk M. A.

    2014-08-01

    Full Text Available Generating sensors provide the possibility of getting remote information and its easy conversion into digital form. Typically, these are one-parameter sensors formed by combination of a primary transmitter (PT and a sine wave generator. Two-parameter sensors are not widely used as their implementation causes a problem with ambiguity output when measuring the PT. Nevertheless, the problem of creating miniature, thrifty multi-parameter RF sensors for different branches of science and industry remains relevant. Considering ways of designing RF sensors, we study the possibility of constructing a three-parameter microwave radio frequency range sensor, which is based on a two-stage three-parameter generalized immitance convertor (GIC. Resistive, inductive and capacitive PT are used as sensing elements. A mathematical model of the sensor, which describes the relation of the sensor parameters to the parameters of GIC and PT was developed. The basic parameters of the sensor, its transfer function and sensitivity were studied. It is shown that the maximum value of the power generated signal will be observed at a frequency of 175 MHz, and the frequency ranges depending on the parameters of the PT will be different. Research results and adequacy of the mathematical model were verified by the experiment. Error of the calculated dependences of the lasing frequency on PT parameters change, compared with the experimental data does not exceed 2 %. The relative sensitivity of the sensor based on two-stage GIC showed that for the resistive channel it is about 1.88, for the capacitive channel –1,54 and for the inductive channel –11,5. Thus, it becomes possible to increase the sensor sensitivity compared with the sensitivity of the PT almost 1,2—2 times, and by using the two stage GIC a multifunctional sensor is provided.

  4. Rare Earth Optical Temperature Sensor

    Science.gov (United States)

    Chubb, Donald L. (Inventor); Jenkins, Phillip (Inventor)

    2004-01-01

    A rare earth optical temperature sensor is disclosed for measuring high temperatures. Optical temperature sensors exist that channel emissions from a sensor to a detector using a light pipe. The invention uses a rare earth emitter to transform the sensed thermal energy into a narrow band width optical signal that travels to a detector using a light pipe. An optical bandpass filter at the detector removes any noise signal outside of the band width of the signal from the emitter.

  5. Cantilever-like micromechanical sensors

    DEFF Research Database (Denmark)

    Boisen, Anja; Dohn, Søren; Keller, Stephan Sylvest

    2011-01-01

    The field of cantilever-based sensing emerged in the mid-1990s and is today a well-known technology for label-free sensing which holds promise as a technique for cheap, portable, sensitive and highly parallel analysis systems. The research in sensor realization as well as sensor applications has...... on silicon-and polymer-based technologies. Examples of recent sensor applications are given covering such diverse fields as drug discovery, food diagnostics, material characterizations and explosives detection....

  6. Sensor networks for sustainable development

    CERN Document Server

    Ilyas, Mohammad; Alwakeel, Mohammed M; Aggoune, el-Hadi M

    2014-01-01

    ContentsPreface AcknowledgmentsEditorsContributorsAgricultureA Review of Applications of Sensor Networks in Smart AgricultureAhsan AbdullahWireless Sensor Networks with Dynamic Nodes for Water and Crop Health Managementel-Hadi M. Aggoune, Sami S. Alwakeel, Mohammed M. Alwakeel, and Mohammad Ammad-UddinEnvironmentScaling Smart EnvironmentsDiane J. CookLocalization of a Wireless Sensor Network for Environment Monitoring using Maximum Likelihood Estimation with Negative

  7. Wireless Sensor Portal Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recognizing the needs and challenges facing NASA Earth Science for data input, manipulation and distribution, Mobitrum is proposing a ? Wireless Sensor Portal...

  8. Fiber-Optic Sensor Facility

    Data.gov (United States)

    Federal Laboratory Consortium — FUNCTION: Constructs and evaluates fiber-optic sensors for a variety of measurands. These measurands include acoustic, pressure, magnetic, and electric field as well...

  9. An inexpensive sensor for noise.

    Science.gov (United States)

    Hallett, Laura; Tatum, Marcus; Thomas, Geb; Sousan, Sinan; Koehler, Kirsten; Peters, Thomas

    2018-02-08

    Noise is a pervasive workplace hazard that varies spatially and temporally. The cost of direct-reading instruments for noise hampers their use in a network. The objectives for this work were to (1) develop an inexpensive noise sensor (noise sensors for use in an inexpensive sensor network. The inexpensive noise sensor consists of an electret condenser microphone, an amplifier circuit, and a microcontroller with a small form factor (28 mm by 47 mm by 9 mm) than can be operated as a stand-alone unit. Laboratory tests were conducted to evaluate 50 of the new sensors at 5 sound levels: (1) ambient sound in a quiet office; (2) a pink noise test signal from 65 to 85 dBA in 10 dBA increments; and (3) 94 dBA using a SLM calibrator. Ninety-four percent of the noise sensors (n = 46) were within ± 2 dBA of the SLM for sound levels from 65 dBA to 94 dBA. As sound level increased, bias decreased, ranging from 18.3% in the quiet office to 0.48% at 94 dBA. Overall bias of the sensors was 0.83% across the 75 dBA to 94 dBA range. These sensors are available for a variety of uses and can be customized for many applications, including incorporation into a stationary sensor network for continuous monitoring of noise in manufacturing environments.

  10. Photon-counting image sensors

    CERN Document Server

    Teranishi, Nobukazu; Theuwissen, Albert; Stoppa, David; Charbon, Edoardo

    2017-01-01

    The field of photon-counting image sensors is advancing rapidly with the development of various solid-state image sensor technologies including single photon avalanche detectors (SPADs) and deep-sub-electron read noise CMOS image sensor pixels. This foundational platform technology will enable opportunities for new imaging modalities and instrumentation for science and industry, as well as new consumer applications. Papers discussing various photon-counting image sensor technologies and selected new applications are presented in this all-invited Special Issue.

  11. MEMS Skin Friction Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Interdisciplinary Consulting Corporation proposes a sensor that offers the unique capability to make non-intrusive, direct, simultaneous mean and fluctuating shear...

  12. JSC Wireless Sensor Network Update

    Science.gov (United States)

    Wagner, Robert

    2010-01-01

    Sensor nodes composed of three basic components... radio module: COTS radio module implementing standardized WSN protocol; treated as WSN modem by main board main board: contains application processor (TI MSP430 microcontroller), memory, power supply; responsible for sensor data acquisition, pre-processing, and task scheduling; re-used in every application with growing library of embedded C code sensor card: contains application-specific sensors, data conditioning hardware, and any advanced hardware not built into main board (DSPs, faster A/D, etc.); requires (re-) development for each application.

  13. High Resolution Flexible Tactile Sensors

    DEFF Research Database (Denmark)

    Drimus, Alin; Bilberg, Arne

    2011-01-01

    This paper describes the development of a tactile sensor for robotics inspired by the human sense of touch. It consists of two parts: a static tactile array sensor based on piezoresistive rubber and a dynamic sensor based on piezoelectric PVDF film. The combination of these two layers addresses...... both spatial distribution of pressure and dynamic events such as contact, release of contact and slip. Data acquisition and object recognition applications are described and it is proposed that such a sensor could be used in robotic grippers to improve object recognition, manipulation of objects...

  14. Micro technology based sun sensor

    DEFF Research Database (Denmark)

    Hales, Jan Harry; Pedersen, Martin; Fléron, René

    2003-01-01

    . This fact enables students to get hands-on experience with satellite systems design and project management. This paper describes the attitude control and determination system of a Danish student satellite (DTUsat), with main focus on the two-axis MOEMS sun sensor developed. On the magnetotorquer controlled...... DTUsat sun sensors are needed along with a magnetometer to obtain unambiguous attitude determination for the ACDS and the payloads - an electrodynamic tether and a camera. The accuracy needed was not obtainable by employing conventional attitude sensors. Hence a linear slit sensor was designed...

  15. Virtual Sensor Test Instrumentation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Smart sensor combining with embedded metadata and wireless technology presents real opportunities for significant improvements in reliability, cost-benefits, and...

  16. A Cryogenic Flow Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Technologies Group, Inc. proposes the development of a Cryogenic Flow Sensor (CFS) for determining mass flow of cryogens in spacecraft propellant...

  17. Robots and sensor clouds

    CERN Document Server

    Shakshuki, Elhadi

    2016-01-01

    This book comprises four chapters that address some of the latest research in clouds robotics and sensor clouds. The first part of the book includes two chapters on cloud robotics. The first chapter introduces a novel resource allocation framework for cloud robotics and proposes a Stackelberg game model and the corresponding task oriented pricing mechanism for resource allocation. In the second chapter, the authors apply Cloud Computing for building a Cloud-Based 3D Point Cloud extractor for stereo images. Their objective is to have a dynamically scalable and applicable to near real-time scenarios.  .

  18. Fluorescent sensor for mercury

    Science.gov (United States)

    Wang, Zidong [Urbana, IL; Lee, Jung Heon [Evanston, IL; Lu, Yi [Champaign, IL

    2011-11-22

    The present invention provides a sensor for detecting mercury, comprising: a first polynucleotide, comprising a first region, and a second region, a second polynucleotide, a third polynucleotide, a fluorophore, and a quencher, wherein the third polynucleotide is optionally linked to the second region; the fluorophore is linked to the first polynucleotide and the quencher is linked to the second polynucleotide, or the fluorophore is linked to the second polynucleotide and the quencher is linked to the first polynucleotide; the first region and the second region hybridize to the second polynucleotide; and the second region binds to the third polynucleotide in the presence of Hg.sup.2+ ions.

  19. Optical humidity sensor

    Science.gov (United States)

    Tarvin, Jeffrey A.

    1987-01-01

    An optical dielectric humidity sensor which includes a dielectric mirror having multiple alternating layers of two porous water-adsorbent dielectric materials with differing indices of refraction carried by a translucent substrate. A narrow-band polarized light source is positioned to direct light energy onto the mirror, and detectors are positioned to receive light energy transmitted through and reflected by the mirror. A ratiometer indicates humidity in the atmosphere which surrounds the dielectric mirror as a function of a ratio of light energies incident on the detectors.

  20. Thermocooling of GMR Sensors

    Science.gov (United States)

    Davis, Despina (Inventor); Bellamkonda, Ramya (Inventor); Mannam, Raja Sekharam (Inventor)

    2013-01-01

    A thermoelectrically cooled GMR sensor having a first thermoelectric layer with an array of nanowires, wherein the nanowires include a diameter of about 1 nanometer to about 1000 nanometers. A plurality of alternating layers of magnetic and nonmagnetic material are positioned over and extend the nanowires to form a GMR assembly. A second thermoelectric layer is positioned over the GMR assembly and extends the nanowires, such that the nanowires have a length of between about 100 nanometers and about 500 microns. Conductors are placed in contact with the first and second thermoelectric layers for connecting the thermoelectric layers to a voltage source.

  1. Extending lifetime of wireless sensor networks using multi-sensor ...

    Indian Academy of Sciences (India)

    SOUMITRA DAS

    LPG pipes laid in deep underwater, waste water monitoring, structural health monitoring and many more [1, 2]. The sensor devices of WSN are responsible for the transfer of information across the sensor network to the base station. (BS), using some techniques that enhance the lifetime of the network by saving a substantial ...

  2. Temperature Sensors Integrated into a CMOS Image Sensor

    NARCIS (Netherlands)

    Abarca Prouza, A.N.; Xie, S.; Markenhof, Jules; Theuwissen, A.J.P.

    2017-01-01

    In this work, a novel approach is presented for measuring relative temperature variations inside the pixel array of a CMOS image sensor itself. This approach can give important information when compensation for dark (current) fixed pattern noise (FPN) is needed. The test image sensor consists of

  3. A Semantic Registry Method Using Sensor Metadata Ontology to Manage Heterogeneous Sensor Information in the Geospatial Sensor Web

    Directory of Open Access Journals (Sweden)

    Changjiang Xiao

    2016-05-01

    Full Text Available Efficient information management and precise discovery of heterogeneous sensors in the Geospatial Sensor Web (GSW are a major challenge. Intelligent sensor management requires a registry service to store and process sensor information efficiently. In this paper, we propose a Sensor Metadata Ontology (SMO to achieve a unified semantic description for heterogeneous sensors that is used to express sensor semantics. Through mapping between the sensor registry information model and the SMO, the sensor metadata could be stored with semantic information for the registry. The framework of a Sensor Semantic Registry Service (SSRS has been successfully implemented for the registration and discovery of heterogeneous sensors. The results of GEOSENSOR-SSRS experiments show that the proposed semantic registry method can be used to enable sharing in an open distributed sensor network as well as to promote accuracy and efficiency of discovery.

  4. A AUTOESTIMA COMO ALIADA DO PROCESSO ENSINOAPRENDIZAGEM

    Directory of Open Access Journals (Sweden)

    Gonçalina dos Santos

    2013-06-01

    Full Text Available O presente trabalho caracteriza-se como um desdobramento de um projeto de pesquisa da Universidade Estadual do Norte Fluminense (UENF, sobre o estudo de um olhar sobre objetos de aprendizagem como metodologia no ensino da matemática à luz da teoria dos registros de representação semiótica. Nosso trabalho visa verificar a influência da aplicação desta metodologia de ensino na autoestima dos educandos. Essa pesquisa foi desenvolvida dentro do método qualitativo e quantitativo descritivo exploratório, tendo a natureza do objeto e dos objetivos propostos neste estudo. A pesquisa foi realizada no Colégio Maria de Nazaré na Cidade do Rio de Janeiro, onde os alunos responderam o questionário de autoestima de Rosenberg (1989. A pesquisa foi composta por dois grupos um de análise experimental e outro de controle. No Brasil a temática da autoestima é pouco abordada cientificamente. Palavra fácil na psicologização das relações humanas. Por auto-estima entende-se a avaliação que o indivíduo faz de si mesmo. Expressa uma atitude de aprovação ou de repulsa de si e engloba o auto-julgamento em relação à competência e valor Em relação às pequenas diferenças apresentadas nos resultados encontrados nos grupo experimental, há dificuldade em se afirmar categoricamente a questão. Ao avaliar a média do grupo de controle no inicio da pesquisa, encontrava-se em 49,28% de autoestima, no final este mesmo grupo apresenta uma redução para 48,23%de autoestima. Já ao avaliar a média do grupo experimental no inicio da pesquisa este encontrava-se com 47,5% de autoestima, obtendo um aumento para 49,5% após a inserção do objeto de aprendizagem nas aulas.

  5. Graphene Electronic Tattoo Sensors.

    Science.gov (United States)

    Kabiri Ameri, Shideh; Ho, Rebecca; Jang, Hongwoo; Tao, Li; Wang, Youhua; Wang, Liu; Schnyer, David M; Akinwande, Deji; Lu, Nanshu

    2017-08-22

    Tattoo-like epidermal sensors are an emerging class of truly wearable electronics, owing to their thinness and softness. While most of them are based on thin metal films, a silicon membrane, or nanoparticle-based printable inks, we report sub-micrometer thick, multimodal electronic tattoo sensors that are made of graphene. The graphene electronic tattoo (GET) is designed as filamentary serpentines and fabricated by a cost- and time-effective "wet transfer, dry patterning" method. It has a total thickness of 463 ± 30 nm, an optical transparency of ∼85%, and a stretchability of more than 40%. The GET can be directly laminated on human skin just like a temporary tattoo and can fully conform to the microscopic morphology of the surface of skin via just van der Waals forces. The open-mesh structure of the GET makes it breathable and its stiffness negligible. A bare GET is able to stay attached to skin for several hours without fracture or delamination. With liquid bandage coverage, a GET may stay functional on the skin for up to several days. As a dry electrode, GET-skin interface impedance is on par with medically used silver/silver-chloride (Ag/AgCl) gel electrodes, while offering superior comfort, mobility, and reliability. GET has been successfully applied to measure electrocardiogram (ECG), electromyogram (EMG), electroencephalogram (EEG), skin temperature, and skin hydration.

  6. Fiber Sensor Technology Today

    Science.gov (United States)

    Hotate, Kazuo

    2006-08-01

    Fiber sensor technologies are overviewed. Since the early 1970s, this field has been developed, on the basis of the same devices and photonic principles as fiber communication technologies. Besides simple configurations, in which the fiber acts only as a data transmission line, sophisticated configurations have also been developed, in which the fiber is used as a device to realize unique sensing mechanisms. The fiber optic gyroscope (FOG) is a good example, and has been developed as an absolute rotation sensor used, for example, for navigation and/or attitude control applications. Compared with traditional spinning-mass gyroscopes, the FOG has advantages, such as a short warming-up time, a light weight, and easy handling. A Japanese satellite, which was launched in August 2005 with a mission to observe the aurora, is controlled with a FOG. The FOG has also been used in consumer applications, such as the camera stabilizer, radio-controlled (RC) helicopter navigation, and the control of humanoid robots. Recently, distributed and multiplexed sensing schemes, in particular, have been studied and developed, in which a long fiber acts like a “nerve” for feeling the strain and/or the temperature distribution along the fiber. Performances of artificial nerve systems have markedly improved within the last couple of years, in spatial resolution and measurement speed. By embedding the “fiber-optic nerve system” in aircraft wings, bridges and tall buildings, these materials and structures can sense damage to prevent disasters.

  7. Infrared Fiber Optic Sensors

    Science.gov (United States)

    1997-01-01

    Successive years of Small Business Innovation Research (SBIR) contracts from Langley Research Center to Sensiv Inc., a joint venture between Foster-Miller Inc. and Isorad, Ltd., assisted in the creation of remote fiber optic sensing systems. NASA's SBIR interest in infrared, fiber optic sensor technology was geared to monitoring the curing cycles of advanced composite materials. These funds helped in the fabrication of an infrared, fiber optic sensor to track the molecular vibrational characteristics of a composite part while it is being cured. Foster-Miller ingenuity allowed infrared transmitting optical fibers to combine with Fourier Transform Infrared spectroscopy to enable remote sensing. Sensiv probes operate in the mid-infrared range of the spectrum, although modifications to the instrument also permits its use in the near-infrared region. The Sensiv needle-probe is built to be placed in a liquid or powder and analyze the chemicals in the mixture. Other applications of the probe system include food processing control; combustion control in furnaces; and maintenance problem solving.

  8. LISA Gravitational Reference Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Sun Kexun [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States); Johann, Ulrich [EADS Astrium GmbH, Immenstaad (Germany); DeBra, Dan B; Buchman, Sasha [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States); Byer, Robert L [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States)

    2007-03-15

    We review state of the art of the gravitational reference sensor (GRS) for the Laser Interferometer Space Antenna (LISA). LISA consists of three identical spacecraft placed at the corners of an equilateral triangle with a 5 million kilometer baseline. In the LISA baseline design, the spacecraft at each corner will have two optical assemblies subtending an angle of 60 degrees. A proof mass (PM) is housed in a GRS located at the center of each assembly. LISA measures the distance variation between PMs separated by 5 million kilometers to a precision of 40 pm/Hz{sup 1/2}. The GRS must shield the PM from external disturbances such as solar wind and functions as a drag-free sensor for spacecraft control. The GRS must minimize the back action and cross talk exerted by measurements themselves. Significant progress has been made in the design, fabrication and testing of the GRS. LISA Pathfinder will fly a test GRS system scheduled around 2009. In addition, there have also been new architectures proposed to simplify the LISA payloads by using a single PM and therefore only one GRS per spacecraft. Further a modular GRS (MGRS) structure is proposed to reduce complexity. Optical sensing and large gap size between the PM and the MGRS housing are proposed to lower the disturbance level. Many experimental, engineering design, and trade off studies are underway.

  9. Characterization of NCPA Infrasound Sensors

    Science.gov (United States)

    Hart, D. M.; Jones, K. R.; Sauter, A.

    2011-12-01

    By adding NCPA (National Center for Physical Acoustics) Infrasound sensors to the eastern-half of the Transportable Array, the scientific community has gained another powerful tool for studying natural processes. In an effort to characterize the sensors, including the effect of the wind filter and acoustical porting, researchers at Sandia National Labs (SNL) FACT Site and IRIS PASSCAL have performed a series of tests that resulted in good agreement with the NCPA-provided response (20mV/Pa +-10%, .007Hz high-pass corner frequency). Through independent testing and verification we have gained confidence in the sensor's linearity over the pressure range tested, a measure of power usage, and a measure of the dynamic range the sensors are capable of delivering, indicating the instruments can measure signals well below the Bowman (2005) Acoustic Low Noise Model up to 8Hz. Researchers at the SNL Fact site have the capabilities not only to test the NCPA sensor in an acoustic pressure chamber, but also to test the equivalent of the entire infrasound system used in the TA stations: NCPA sensor, tubing, and wind reduction design (a PVC filter buried in a bag of pumice stone). SNL tests with this fully-ported infrasound system characterize the full system response. We found that the tubing used to port the sensor to the external wind reduction device adds a measurable 15Hz resonance to the response and influences the high-frequency roll-off point. At PASSCAL, we have performed an acceptance test on more than 350 NCPA sensors, and in the process, have collected statistics on their relative gains. The standard deviation of the relative gain for all measured sensors is 5.32%. For 59 repeated tests of the two NCPA sensors used as references, the standard deviation is .15%, which suggests that acceptance testing can be used to constrain the gain of individual NCPA sensors much tighter than the population deviation.

  10. REVIEW ARTICLE: A taste sensor

    Science.gov (United States)

    Toko, Kiyoshi

    1998-12-01

    A multichannel taste sensor, namely an electronic tongue, with global selectivity is composed of several kinds of lipid/polymer membranes for transforming information about substances producing taste into electrical signals, which are input to a computer. The sensor output exhibits different patterns for chemical substances which have different taste qualities such as saltiness, sourness and bitterness, whereas it exhibits similar patterns for chemical substances with similar tastes. The sensor responds to the taste itself, as can be understood from the fact that taste interactions such as the suppression effect, which appears for mixtures of sweet and bitter substances, can be reproduced well. The suppression of the bitterness of quinine and a drug substance by sucrose can be quantified. Amino acids can be classified into several groups according to their own tastes on the basis of sensor outputs. The tastes of foodstuffs such as beer, coffee, mineral water, milk, sake, rice, soybean paste and vegetables can be discussed quantitatively using the taste sensor, which provides the objective scale for the human sensory expression. The flavour of a wine is also discriminated using the taste-odour sensory fusion conducted by combining the taste sensor and an odour-sensor array using conducting polymer elements. The taste sensor can also be applied to measurements of water pollution. Miniaturization of the taste sensor using FET produces the same characteristics as those of the above taste sensor by measuring the gate-source voltage. Use of the taste sensor will lead to a new era of food and environmental sciences.

  11. Sensors Applications, Volume 2, Sensors in Intelligent Buildings

    Science.gov (United States)

    Gassmann, Oliver; Meixner, Hans

    2001-06-01

    Taken as a whole, this series covers all major fields of application for commercial sensors, as well as their manufacturing techniques and major types. As such the series does not treat bulk sensors, but rather places strong emphasis on microsensors, microsystems and integrated electronic sensor packages. Each of the individual volumes is tailored to the needs and queries of readers from the relevant branch of industry. A comprehensive survey for engineers and scientists on the different sensor types for energy efficiency, security, maintenance management and smart house devices. As such, the text covers air conditioning, large premises control, service and installation monitoring as well as emergency control. It also discusses the strengths and weaknesses in each case, illustrating which sensor is used in which subsystem and why.

  12. Quando um primitivo é como um orbe? Quando um primitivo é como um orbe?

    Directory of Open Access Journals (Sweden)

    J. Hillis Miller

    2008-04-01

    Full Text Available Minhas estratégias de analise textual se tornarão mais ou menos evidentes na leitura que se segue. Sua proveniência deveriam tornar-se & cia. 0 ensaio foi inicialmente pensado come parte do livro The Linguistic Moment (Princeton: Princeton University Press, 1985. Aqui, como no livro, minha preocupação maior e com aqueles momentos em poemas em que a poesia como meio de comunicação constitui problema. Interessa-me particularmente a forma pela qual as fronteiras entre a linguagem conceitual e a figurative se tornam pouco visiveis no poema "A Primitive like an Orb", da última fase da poesia de Wallace Stevens.

  13. La moneda como ofrenda en los manantiales

    Directory of Open Access Journals (Sweden)

    Manuel Abad Varela

    1992-01-01

    Full Text Available A la vista de como se han producido la mayoría de los hallazgos analizados y según se desprende de las fuentes escritas, diríamos que en la península ibérica y sobre todo en la parte Occidental se realizaron en la Antigüedad ofrendas monetales a divinidades de las aguas y fundamentalmente, por las referencias que tenemos, a las divinidades de las fuentes termales. Únicamente nos queda la duda de si la fuente de Peña Cutral en Retortillo (Reinosa, Santander es termal o no, pues si no lo fuese sería el único hallazgo dentro de una fuente no termal. Se podría entender, con ciertos reparos en algún caso, que también se hicieron arrojándolas al curso de los ríos, depositándolas en la orilla y lanzándolas a las charcas o pantanos. Por otro lado, las monedas que se han encontrado en las fuentes, en contraposición con las recogidas en los ríos, suelen estar en muy mala conservación, hasta el punto de que muchas se desintegran en las manos al estar muy atacadas por los ácidos. A juzgar por algunos de los hallazgos, se podría creer que las ofrendas más valiosas se procuró depositarlas en lugares seguros o resguardados, como es el caso de la Hermida, de la Fuente de El Sarso, del Balneario de Fortuna y podríamos recordar también el hallazgo del conocido depósito de Oñate. De acuerdo con la cronología de las monedas y según sus resultados estadísticos, la costumbre o rito de depositar o arrojar «stips» a las aguas, principalmente termales, se practicó en la península Ibérica más intensamente entre los siglos i a. C. al ii d. C. Este período coincide con el momento que más estuvo en boga el uso de las aguas termales, a juzgar por lo que se trató el tema en las fuentes escritas. Al mismo tiempo que se percibe esta moda en la vida diaria, pues Suetonio nos dice que Augusto, a pesar de que por su naturaleza enfermiza no abusaba de los baños, sin embargo, cuando necesitaba templar los nervios tomaba baños de mar o las

  14. A CIDADE COMO NEGÓCIO

    Directory of Open Access Journals (Sweden)

    Inaiá de Carvalho

    2013-09-01

    Full Text Available As transformações atuais das grandes metrópoles vêm adquirindo um certo destaque na agenda da pesquisa urbana. Inserindo-se nesse debate, este artigo analisa o novo protagonismo do capital imobiliário no desenvolvimento dessas cidades, a partir de um estudo de caso sobre Salvador, a primeira capital e hoje a terceira maior cidade brasileira. Para tanto, o texto começa abordando a literatura sobre os impactos das transformações associadas à globalização sobre essas cidades. Destaca, entre as mesmas, o abandono por parte do Estado de boa parte de suas funções tradicionais de planejamento e gestão urbana, que vêm se transferindo para atores privados, levando a uma afirmação da lógica do capital imobiliário na produção e reprodução da cidade. Mostra, a seguir, como isto vem se dando no caso de Salvador, com impactos bastante adversos sobre a estrutura e a vida urbana.

  15. El arte como investigación

    Directory of Open Access Journals (Sweden)

    Jaime Cerón Silva

    2012-06-01

    Full Text Available “Si el placer de la interpretación modernista consisteen el efecto del reconocimiento que “educa y refina”el carácter inquietante de su objeto […] la meta deltratamiento posmodernista es separarlo de su carácterfamiliar”(Zizek, 1994, p. 8 Dentro del célebre libro Todo lo que usted siempre quiso saber sobre Lacan y nunca se atrevió a preguntarle a Hitchcock, Slavoj Zizek se pregunta acerca de las transformaciones que involucra la noción de interpretación en el paso del modernismo al posmodernismo. Si ambos periodos parten de concebir un objeto como inseparable de su interpretación, en el primer caso ésta nos llevará a una familiarización con el carácter inquietante de su objeto, mientras que en el segundo a una separación de cualquier posible familiaridad frente a él. Ante la más simple estructura, por digerible y banal que parezca, el posmodernismo siempre encontrará un hecho siniestro, que encierre algo inquietante, extraño o misterioso. Una especie de retorno de lo reprimido.

  16. Daimien Hirst : el artista como preparador

    Directory of Open Access Journals (Sweden)

    Nike Verena Fakiner

    2006-01-01

    Full Text Available El cuerpo más allá de su razón biológica, es un espacio de proyección donde se escenifican las normas y los valores socioculturales y científicos. La ciencia médica constituye un régimen escópico, en cuyo marco se construye un imaginario acerca del cuerpo, que modela y normaliza la percepción que el sujeto moderno establece con él. Hirst trabaja desde el cuerpo muerto, como medio y material de trabajo, para cuestionar el posicionamiento del cuerpo en el discurso de la medicina. Para ello se sirve de imágenes corporales situadas en la frontera entre Medicina y Arte.The body, beyond its biological meaning, is a space of projection of cultural and scientific norms and values. The medicine constitutes a scopic regime, where an imaginary of body is built up which normalizes its perception by the modern subject. Hirst works with the dead body as medium and material of work, in order to question body` s position in medicine discourse. Therefore, he works with body images placed on the border line between Medicine and Art.

  17. El budismo como una espiritualidad no religiosa

    Directory of Open Access Journals (Sweden)

    Marta Granés Bayona

    2014-09-01

    Full Text Available El budismo plantea acceder a una visión de la realidad desligada de creencias y supuestos de todo tipo. Para conseguirlo plantea una indagación libre en referencia al enclaustramiento de nuestro pensar y sentir al que nos somete el ego. El ego con sus necesidades y deseos genera un acceso a la realidad relativo a nosotros. Lo que se propone es una liberación de esta lectura para que la realidad pueda aparecer frente a nosotros de manera independiente de las imposiciones del ego, es decir, un acceso a ella ab-soluto (suelto de nosotros. El budismo es, pues, una propuesta de ‘espiritualidad no religiosa’, para la que el mismo término espiritualidad  resultaría inadecuado porque en él subyace la creencia en el ‘espíritu’. Vemos que por todo ello el mensaje budista resulta muy apropiado para las sociedades hoy presentes, bien para aquellas que están transitando de una sociedad agrícola a una industrial, que conlleva a debilitar las convicciones religiosas hasta disolverlas; bien para aquellas que están próximas o han entrado ya en las sociedades llamadas de conocimiento, innovación y cambio continuo cuya condición de movilidad impide  las creencias, porque son fijadoras, lo que arrastra como consecuencia la imposibilidad de tener religión ni espiritualidad. 

  18. ESPACIOS RENATURALIZADOS COMO AMBIENTES DE APRENDIZAJE

    Directory of Open Access Journals (Sweden)

    Yenny Rosas

    2015-12-01

    Los espacios renaturalizados, se consolidan como ambientes de aprendizaje para el ejercicio de la ciudadanía y la convivencia, a partir del desarrollo de metodologías participativas y haciendo uso de tecnologías apropiadas. Para ello se diseñaron e implementaron una serie de sesiones, con el fin de contribuir a la transformación del entorno y de permitir la conectividad ecológica presente en el ecosistema estratégico ubicado allí mismo, además de consolidar experiencias en el desarrollo de capacidades ciudadanas esenciales. Para la institución educativa se construyó, un jardín agroecológico y se sembraron árboles con fines productivos y ornamentales, permitiendo de esa manera la generación de identidad con respecto a los espacios renaturalizados, la estructura ecológica, además de reconocer las relaciones socio-ecológicas que alrededor de estos espacios se desarrollan. Entorno a la intervención, se construyeron conocimientos propios del currículo, además se identificaron las problemáticas ambientales propias de la zona, permitiendo de esa manera la armonización de la relación naturaleza-cultura y la adaptación ecosistémica al cambio climático, que requiere la ciudad de Bogotá.

  19. Ensinar cirurgia: como e para quem?

    Directory of Open Access Journals (Sweden)

    Lisieux Eyer de Jesus

    Full Text Available O autor discute a crise atual de formação de médicos e de cirurgiões fazendo uma revisão de dados de literatura atual, referentes ao quantitativo de médicos e discussão de referências éticas e filosóficas da profissão. Há uma diminuição crescente na formação de médicos e cirurgiões, com uma crescente participação de mulheres. Os médicos jovens buscam qualidade de vida e autonomia profissional como principais requisitos profissionais. As síndromes de burn-out são comuns entre os médicos em atividade, e a perda de autonomia profissional tem papel preponderante na determinação da doença. A crise que atinge a profissão médica e as especialidades cirúrgicas tem bases éticas, sociais e financeiras. É necessário e fundamental discutir novos paradigmas de educação e atuação profissional na sociedade moderna.

  20. Como obter vantagem competitiva utilizando business intelligence?

    Directory of Open Access Journals (Sweden)

    Avanilde Kemczinski

    2003-03-01

    Full Text Available Este artigo tem por objetivo definir Business Intelligence e identificar as tecnologias de informação e comunicação que dão suporte a este tipo de sistema de informação. Faz-se uma contextualização sobre o conceito e as tipologias de sistemas de informação (SI. Data Warehouse, Data Mart e Data Mining são os recursos tecnológicos denominados de Back-end system, utilizados para armazenar dados relevantes e extrair padrões de comportamento e tendências dos processos organizacionais. Os DSS (Decision Support Systems, EIS (Executive Information Systems e ferramentas de OLAP (On-Line Analytical Processing são caracterizados como Front-end systems para os sistemas de Business Intelligence, requerendo-se ampla funcionalidade, flexibilidade e usabilidade para que o usuário possa fazer a transformação das informações em conhecimento estratégico que apóie a tomada de decisão organizacional, objetivando a vantagem competitiva. Palavras-chave: Sistemas de Informação, Business Intelligence, Data Mining, Data Warehouse, OLAP.

  1. COMO MEDIR INFORMAÇÃO?

    Directory of Open Access Journals (Sweden)

    Herman do Lago Mendes

    2017-12-01

    Full Text Available Por meio de ilustrações e resoluções de problemas, objetiva explicar como se mede informação. Para tal, recorre à teoria matemática da comunicação de Shannon. Esta teoria foi inicialmente elaborada para explicar transmissões de informações através de sistemas de telecomunicações a fim de corrigir erros entre a origem e o destino da informação. Mostra que a quantificação de informação parte da elaboração de estratégias de escolha entre duas mensagens ou signos. Medir informação significa contar o número de escolhas entre dois signos. Quantificar informação parte de axiomas, equações, conceitos de probabilidade e de funções logarítmicas para reduzir a incerteza do sinal de qualquer canal (meio físico de comunicação.

  2. El lenguaje como instrumento de poder

    Directory of Open Access Journals (Sweden)

    LISBETH CAROLINA ROJAS BERMÚDEZ

    2008-01-01

    Full Text Available Las recientes investigaciones en lingüística dentro de las que se destacan las adelantadas por Meyer, Fairclough & Wodak y Van Dijk, han coincidido en que mediante las prácticas discursivas se ejerce poder, dado que, quien emite un discurso busca, ante todo, persuadir a los receptores, a través de creencias, actitudes, valores y un sinnúmero de saberes tomados de su entorno y la cultura. La relación discurso-poder está dada por el control "sutil" que se ejerce sobre las mentes de un grupo determinado, a partir del lenguaje. En palabras de Jäger, mediante los discursos es posible "inducir comportamientos y generar (otros discursos. De este modo, contribuyen a la estructuración de las relaciones de poder en una sociedad". Este artículo pretende explicar, a partir del ACD, cómo dicha relación se manifiesta a través de algunas estrategias discursivas, tales como el uso de determinadas estructuras semánticas sintácticas, marcadores discursivos y fenómenos de polifonía, entre otras, las cuales son utilizadas en los discursos políticos y ayudan a evidenciar marcas lingüísticas de poder.

  3. LA PIZARRA DIGITAL INTERACTIVA COMO RECURSO DOCENTE

    Directory of Open Access Journals (Sweden)

    Domingo J. Gallego

    2010-12-01

    Full Text Available La Pizarra Digital Interactiva (PDI es un recurso de grandes posibilidades educativas para los docentes. En este artículo se presentan los resultados de distintas investigaciones que han analizado el uso de la PDI a través de distintos programas de formación docente en distintos niveles educativos y áreas curriculares. A diferencia de otros recursos en los que el docente está en un «segundo plano», una de las ventajas del uso de la PDI es la cercanía al modelo tradicional de enseñanza en la que el profesor presenta los contenidos principales para pasar a las actividades de aprendizaje individuales y grupales. En la sociedad del conocimiento el docente debe adaptar su metodología aprovechando la riqueza de los recursos que ofrece la red y que están disponibles en el aula a través de la PDI, así como la creación de recursos propios integrando objetos multimedia disponibles.

  4. A cordialidade como mal-estar ou a violência como o recalcado

    Directory of Open Access Journals (Sweden)

    Mériti de Souza

    Full Text Available Neste estudo problematizamos a constituição da subjetividade orientada pelo discurso que adota o mito do brasileiro cordial como modelo identificatório. Utilizando do referencial psicanalítico, analisamos discursos presentes na história nacional que abordam essa questão, interrogando sobre o recalque da violência e suas conseqüências sobre a subjetividade. Avaliamos que o discurso da cordialidade funciona como forma de controle e de manutenção do status quo, ao gratificar e oferecer uma representação pretensamente valorizada do brasileiro. Ainda, esse discurso produz o recalque da violência e o seu retorno sob a forma de domínio, ou seja, de exercício do controle sobre o coro e o desejo do outro, manifesto nas práticas de dominação social e sexual. Os modelos identificatórios da cordialidade e do domínio, funcionam como extremos complementares, associados ao recalque da violência. Finalizando, perguntamos sobre as práticas psicoterápicas e psicanalíticas desenvolvidas no cenário nacional, a partir da inserção de psicoterapeutas e psicanalistas nesse contexto cultural.

  5. Josep Beuys : el arte como creencia y como salvación

    Directory of Open Access Journals (Sweden)

    María López Ruido

    1995-01-01

    Full Text Available Joseph Beuys, nacido en Cléveris (Renania del Norte-Westfalia en 1921 y faliecido en Dusseldorf en 1986, posee una obra madura casi desde un primer momento. Superficialmente podríamos verla como el canto a sí mismo de un gran narcisista, donde sus experiencias y su persona son los grandes protagonistas. En una lectura más profunda, estos hechos personales no son más que el medio para ir más allá del yo y dar lugar a una creación plástica de trascendencia social. Tras la 2- Guerra Mundial, en la que lucha como piloto de la Luftwaffe, estudia en la Academia de Bellas Artes de Dusseldorf. Será a partir de los años 60 cuando encontremos al auténtico Beuys, escultor objetual e instalador, el creador de la plástica social, y desde sus contactos con Fluxus en 1962, el Beuys accionista. En los 70, se nos presenta el artista más claramente politizado. La educación, la incidencia social del arte, el arte como «tercera vía o vía alternativa» entre socialismo y capitalismo, la ecología serán sus materiales de trabajo.

  6. Sensors, Volume 1, Fundamentals and General Aspects

    Science.gov (United States)

    Grandke, Thomas; Ko, Wen H.

    1996-12-01

    'Sensors' is the first self-contained series to deal with the whole area of sensors. It describes general aspects, technical and physical fundamentals, construction, function, applications and developments of the various types of sensors. This volume deals with the fundamentals and common principles of sensors and covers the wide areas of principles, technologies, signal processing, and applications. Contents include: Sensor Fundamentals, e.g. Sensor Parameters, Modeling, Design and Packaging; Basic Sensor Technologies, e.g. Thin and Thick Films, Integrated Magnetic Sensors, Optical Fibres and Intergrated Optics, Ceramics and Oxides; Sensor Interfaces, e.g. Signal Processing, Multisensor Signal Processing, Smart Sensors, Interface Systems; Sensor Applications, e.g. Automotive: On-board Sensors, Traffic Surveillance and Control, Home Appliances, Environmental Monitoring, etc. This volume is an indispensable reference work and text book for both specialits and newcomers, researchers and developers.

  7. Sensor Integration Using State Estimators

    Directory of Open Access Journals (Sweden)

    Jens G. Balchen

    1991-04-01

    Full Text Available Means for including very different types of sensors using one single unit are described. Accumulated data are represented using an updatable dynamic model, a Kalman filter. The scheme handles common phenomena such as skewed sampling, finite resolution measurements and information delays. Included is an example where 3D motion information is collected by one or more vision sensors.

  8. Lightweight, Wearable, Metal Rubber Sensor

    Science.gov (United States)

    Hill, Andrea

    2015-01-01

    For autonomous health monitoring. NanoSonic, Inc., has developed comfortable garments with multiple integrated sensors designed to monitor astronaut health throughout long-duration space missions. The combined high electrical conductivity, low mechanical modulus, and environmental robustness of the sensors make them an effective, lightweight, and comfortable alternative to conventional use of metal wiring and cabling.

  9. Non-intrusive refractometer sensor

    Indian Academy of Sciences (India)

    Abstract. An experimental realization of a simple non-intrusive refractometer sensor is demonstrated in this communication. The working principle of the sensor is based on intensity modulation of the back-reflected light when output light from an optical fibre end focusses onto air–medium interface. The change in the ...

  10. Electronically-Scanned Pressure Sensors

    Science.gov (United States)

    Coe, C. F.; Parra, G. T.; Kauffman, R. C.

    1984-01-01

    Sensors not pneumatically switched. Electronic pressure-transducer scanning system constructed in modular form. Pressure transducer modules and analog to digital converter module small enough to fit within cavities of average-sized wind-tunnel models. All switching done electronically. Temperature controlled environment maintained within sensor modules so accuracy maintained while ambient temperature varies.

  11. Monolithic fiber optic sensor assembly

    Science.gov (United States)

    Sanders, Scott

    2015-02-10

    A remote sensor element for spectrographic measurements employs a monolithic assembly of one or two fiber optics to two optical elements separated by a supporting structure to allow the flow of gases or particulates therebetween. In a preferred embodiment, the sensor element components are fused ceramic to resist high temperatures and failure from large temperature changes.

  12. Guides for flow sensors selection; Guias para la seleccion de sensores de flujo

    Energy Technology Data Exchange (ETDEWEB)

    Gomez Garcia, Gustavo; Guzman Flores, Roberto; Rodriguez Martinez, Arnulfo [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1995-12-31

    In this paper a system is presented that allows the selection and calculation on instruments for flow measurement, based on practical experiences, standards an taking into consideration the process operational characteristics such as fluid type, maximum flow rate, piping diameter, etc. The system is composed of a knowledge base and a software for the selection, calculation and de adequate recommendation of flow sensing elements for the different services needed in the power plants. [Espanol] En este trabajo se presenta un sistema que permite realizar la seleccion y calculo de instrumentos para la medicion de flujo con base en experiencias practicas, normas y tomando en cuenta las caracteristicas de operacion del proceso como el tipo de fluido, flujo maximo, diametro de tuberia, etcetera. El sistema esta compuesto por una base de conocimiento y un software para la seleccion, calculo y la recomendacion adecuada de elementos sensores de flujo para los diferentes servicios que se tienen en centrales generadoras.

  13. Color Changing Hydrogen Sensors

    Science.gov (United States)

    Roberson, Luke B.; Williams, Martha; Captain, Janine E.; Mohajeri, Nahid; Raissi, Ali

    2015-01-01

    During the Space Shuttle Program, one of the most hazardous operation that occurred was the loading of liquid hydrogen (LH2) during fueling operations of the spacecraft. Due to hydrogen's low explosive limit, any amount leaked could lead to catastrophic event. Hydrogen's chemical properties make it ideal as a rocket fuel; however, the fuel is deemed unsafe for most commercial use because of the inability to easily detect the gas leaking. The increased use of hydrogen over traditional fossil fuels would reduce greenhouse gases and America's dependency on foreign oil. Therefore a technology that would improve safety at NASA and in the commercial sector while creating a new economic sector would have a huge impact to NASA's mission. The Chemochromic Detector for sensing hydrogen gas leakage is a color-changing detector that is useful in any application where it is important to know not only the presence but also the location of the hydrogen gas leak. This technology utilizes a chemochromicpigment and polymer matrix that can be molded or spun into rigid or pliable shapes useable in variable temperature environments including atmospheres of inert gas, hydrogen gas, or mixtures of gases. A change in color of the detector material indicates where gaseous hydrogen leaks are occurring. The irreversible sensor has a dramatic color change from beige to dark grey and remains dark grey after exposure. A reversible pigment changes from white to blue in the presence of hydrogen and reverts back to white in the presence of oxygen. Both versions of the sensor's pigments were comprised of a mixture of a metal oxide substrate and a hydro-chromic compound (i.e., the compound that changed color in the presence of hydrogen) and immediately notified the operator of the presence of low levels of hydrogen. The detector can be used in a variety of formats including paint, tape, caulking, injection molded parts, textiles and fabrics, composites, and films. This technology brings numerous

  14. Novel concepts in Hall sensors

    Science.gov (United States)

    Mani, R. G.

    1996-03-01

    Hall effect devices are widely used as position sensors and contactless switches in applications ranging from electric motors to soft drink machines and automobiles. Such devices typically operate in an adverse environment where offset voltages originating from various physical effects limit the effective sensitivity of the sensor to the weak magnetic field (B device that automatically reduces such spurious offsets is desirable because improved 'signal to offset' would relax manufacturing tolerances and other constraints within the sensor system. Here, we examine some techniques and sensor configurations (R. G. Mani, K. von Klitzing, F. Jost, K. Marx, S. Lindenkreuz, and H. P. Trah, Appl. Phys. Lett. 67, 2223, 1995.) based on the so called 'anti Hall bar' geometry that promise the possibility of a Silicon based Hall sensor with a field equivalent offset well below 1 mT.

  15. Integrated Passive And Wireless Sensor

    KAUST Repository

    Li, Bodong

    2015-04-30

    A passive and wireless sensor is provided for sensing at least one of magnetic field, temperature or humidity. The sensor can provide only one of the sensing functions, individually or any combination of them simultaneously. It can be used for various applications where magnetic field changes, temperature and/or humidity need to be measured. In one or more embodiments, a surface acoustic wave (SAW) sensor is provided that can measure one or more of a magnetic field (or current that generates the magnetic field), temperature and humidity. In one or more embodiments, a magnetoimpedence (MI) sensor (for example a thin film giant magnetoimpedance (GMI) sensor), a thermally sensitive (for example a Lithium Niobite (LiNbO.sub.3)) substrate, and a humidity sensitive film (for example a hydrogel film) can be used as sensing elements.

  16. Hall Sensors for Extreme Temperatures

    Directory of Open Access Journals (Sweden)

    Maciej Oszwaldowski

    2011-01-01

    Full Text Available We report on the preparation of the first complete extreme temperature Hall sensor. This means that the extreme-temperature magnetic sensitive semiconductor structure is built-in an extreme-temperature package especially designed for that purpose. The working temperature range of the sensor extends from −270 °C to +300 °C. The extreme-temperature Hall-sensor active element is a heavily n-doped InSb layer epitaxially grown on GaAs. The magnetic sensitivity of the sensor is ca. 100 mV/T and its temperature coefficient is less than 0.04 %/K. This sensor may find applications in the car, aircraft, spacecraft, military and oil and gas industries.

  17. Energy efficient sensor network implementations

    Energy Technology Data Exchange (ETDEWEB)

    Frigo, Janette R [Los Alamos National Laboratory; Raby, Eric Y [Los Alamos National Laboratory; Brennan, Sean M [Los Alamos National Laboratory; Kulathumani, Vinod [WEST VIRGINIA UNIV.; Rosten, Ed [CAMBRIDGE UNIV.; Wolinski, Christophe [IRISA; Wagner, Charles [IRISA; Charot, Francois [IRISA

    2009-01-01

    In this paper, we discuss a low power embedded sensor node architecture we are developing for distributed sensor network systems deployed in a natural environment. In particular, we examine the sensor node for energy efficient processing-at-the-sensor. We analyze the following modes of operation; event detection, sleep(wake-up), data acquisition, data processing modes using low power, high performance embedded technology such as specialized embedded DSP processors and a low power FPGAs at the sensing node. We use compute intensive sensor node applications: an acoustic vehicle classifier (frequency domain analysis) and a video license plate identification application (learning algorithm) as a case study. We report performance and total energy usage for our system implementations and discuss the system architecture design trade offs.

  18. Fiber loop ringdown humidity sensor.

    Science.gov (United States)

    Alali, Haifa; Wang, Chuji

    2016-11-01

    An optical fiber relative humidity (RH) sensor based on the evanescent field-fiber loop ringdown (EF-FLRD) technique is demonstrated. The sensor was placed inside a chamber that provides a humidity reference and is monitored by a humidity meter. The presence of moisture in the chamber changes the refractive index of the medium; thus the ringdown time changes due to a change in the EF scattering loss induced in the sensor head. The sensor demonstrated a fast response (∼1  s), high sensitivity, and excellent reproducibility and reversibly. The EF-FLRD sensor can measure RH in a wide dynamic range of 4% to 100% at a constant temperature of 20±1°C.

  19. Optical Fiber Grating based Sensors

    DEFF Research Database (Denmark)

    Michelsen, Susanne

    2003-01-01

    In this thesis differenct optical fiber gratings are used for sensor purposes. If a fiber with a core concentricity error (CCE) is used, a directional dependent bend sensor can be produced. The CCE direction can be determined by means of diffraction. This makes it possible to produce long......-period gratings in a fiber with a CCE direction parallel or perpendicular to the writing direction. The maximal bending sensitivity is independent on the writing direction, but the detailed bending response is different in the two cases. A temperature and strain sensor, based on a long-period grating and two...... sampled gratings, was produced and investigated. It is based on the different temperature and strain response of these gratings. Both a transfer matrix method and an overlap calculation is performed to explain the sensor response. Another type of sensor is based on tuning and modulation of a laser...

  20. Flexible Temperature Sensors on Fibers

    Directory of Open Access Journals (Sweden)

    Marcin Sloma

    2010-08-01

    Full Text Available The aim of this paper is to present research dedicated to the elaboration of novel, miniaturized flexible temperature sensors for textronic applications. Examined sensors were manufactured on a single yarn, which ensures their high flexibility and good compatibility with textiles. Stable and linear characteristics were obtained by special technological process and applied temperature profiles. As a thermo-sensitive materials the innovative polymer compositions filled with multiwalled carbon nanotubes were used. Elaborated material was adapted to printing and dip-coating techniques to produce NTC composites. Nanotube sensors were free from tensometric effect typical for other carbon-polymer sensor, and demonstrated TCR of 0.13%/K. Obtained temperature sensors, compatible with textile structure, can be applied in rapidly developing smart textiles and be used for health and protections purposes.

  1. Sensores para evaluar la calidad de frutas y hortalizas.

    OpenAIRE

    Ruiz-Altisent, Margarita

    2012-01-01

    En la presente contribución se hace una revisión somera de los principales sensores, tanto de las tecnologías subyacentes como de los equipos utilizables, que sirven para evaluar la calidad de frutas y hortalizas de forma no-invasiva. Se distingue entre tecnologías asentadas, viables técnicamente, o con viabilidad comercial, y a continuación de introduce brevemente nuevas técnicas en desarrollo que pueden ser viables para en un plazo previsible. Se describe, desde una aproximación general de ...

  2. Sensores magnetorresistivos para aplicações de biomagnetismo

    OpenAIRE

    Fabiano Miranda da Silva

    2009-01-01

    O laboratório de biomagnetismo tem realizado com sucesso estudos da motilidade gastrointestinal medindo tempos de trânsito e de esvaziamento de diferentes segmentos do trato gastrointestinal. Nesse estudo tanto a magnetização remanente como a susceptibilidade magnética de diferentes regiões do trato gastrointestinal são medidas. Os sensores magnetoresistivos serão utilizados para estudo de marcadores ferromagnéticos ou pequenos imãs (aproximados por dipolos magnéticos) in vitro, que possibili...

  3. Modelado y desarrollo de microcantilevers resonantes para sensores

    OpenAIRE

    Narducci Marín, Margarita Sofía

    2011-01-01

    Descripció del recurs: el 13 setembre 2011 Esta tesis está enfocada en el diseño, simulación, fabricación y caracterización de sensores de masa basados en microcantilevers de silicio. Los cantilevers con forma de T son diseñados como estructuras formadas por 3 vigas unidas en su extremo por medio de una masa rectangular extra. Los cantilevers son excitados para alcanzar su resonancia mecánica, en modo flexión perpendicular al sustrato, con un piezoactuador PZT pegado en la parte posterior ...

  4. Como Lo Hago Yo: Mielomeningocele En Bolivia

    Science.gov (United States)

    Dabdoub, Carlos F.; Dabdoub, Carlos B.; Villavicencio, Ramiro; Quevedo, Germán

    2014-01-01

    Introducción: Las malformaciones del tubo neural (MTN) representan la segunda causa más frecuente de anomalías congénitas, luego de las cardiopatías. En este grupo se destaca el mielomeningocele (MMC) por su mayor incidencia, y por ser la más incapacitante y la más compleja entre todas las demás malformaciones del sistema nervioso c`entral (SNC). En Bolivia, como en muchos países de Sudamérica, los bajos niveles socio-culturales y la debilidad en el sistema sanitario, hacen que su incidencia y su morbilidad, sean mayores que en las naciones más desarrolladas. Material y Métodos: Se realizó un estudio retrospectivo y descriptivo de 70 casos de MMC, atendidos por un equipo multidisciplinario en el Hospital Universitario Japonés (HUJ) de Santa Cruz de la Sierra, entre 2008-2011. De ellos, 60 fueron intervenidos quirúrgicamente. Resultados: Se realizaron controles prenatales sólo en 27 mujeres (38.6%), diagnosticándose una disrafia espinal en apenas dos casos (7.4%). La edad de ingreso del MMC en su mayoría fue después de las 24 horas (65.6%), predominando su localización en la región lumbosacra (64.3%). De ellos, 67.2% eran abiertos, presentando un 32.9% un daño neurológico motor parcial mientras que 47.1% tenían paraplejia por debajo de la lesión. De los 70 casos, tres (4.3%) no fueron intervenidos, por presentar defectos congénitos severos o estado general grave. Las principales complicaciones posoperatorias inmediatas fueron: dehiscencia de sutura y/o infección de la herida (16.6%), fístula de líquido cefalorraquídeo (LCR) (10%) e infección del SNC (11.7%). La mortalidad general y postoperatoria fue de 7.1% y 3.3%, respectivamente. Al mes de vida presentaban hidrocefalia un 80% de los pacientes operados, colocándose una derivación ventriculoperitoneal (DVP) de presión media. De 9 pacientes que tuvieron un acompanamiento de dos o más años, seis presentaron una médula anclada, que fueron intervenidas quirúrgicamente. Conclusi

  5. La participacion ciudadana como fuente de democracia

    Directory of Open Access Journals (Sweden)

    Orlando José Cadrazco Salcedo

    2009-01-01

    Full Text Available Resumen:La Participación ciudadana es un órgano de deliberación donde confluyen todos los factores reales de poder paradecidir sobre aspectos como el plan de desarrollo, plan de ordenamiento territorial y presupuesto (atendiendo alente territorial donde se establezca , en sí este modelo es un verdadero desarrollo del concepto de democraciaparticipativa que consagra nuestra Carta Política, es un ejemplo de que la soberanía popular consagrada en elartículo tercero de la Carta va más allá del formalismo legalista y los intrincados vericuetos de la ley 134 de 1994que nunca han permitido que se ponga en marcha un verdadero desarrollo de la democracia participativa, y quepor fin salgamos de ese esquema retrogrado de la representatividad y por supuesto que a través de este modelolleguemos a un verdadero contrato social que provenga de las bases.Palabras claves:Democracia Participativa. Carta Politica, Sociedad, Participaciòn Ciudadana, Modelo Democrático, ConstituciónPolítica.Abstract:Citizen participation is a deliberative body where all the real power to decide on aspects such as the developmentplan, development plan and budget (according to the local authority where it is established, this model is itself atrue development the concept of participatory democracy enshrined in our Constitution, is an example of popularsovereignty enshrined in the third article of the Charter goes beyond the legal formalities and vericuetos the intricaciesof the law 134 of 1994 which have never been allowed to put ongoing development of a true participatorydemocracy, and they finally get out of this backward scheme of representation and of course that through this modelto create a real social contract comes from the grassroots.Keywords:Participatory Democracy. Charter Politics, Society, Politics, democratic, Constitution.

  6. Ion mobility sensor system

    Science.gov (United States)

    Xu, Jun; Watson, David B.; Whitten, William B.

    2013-01-22

    An ion mobility sensor system including an ion mobility spectrometer and a differential mobility spectrometer coupled to the ion mobility spectrometer. The ion mobility spectrometer has a first chamber having first end and a second end extending along a first direction, and a first electrode system that generates a constant electric field parallel to the first direction. The differential mobility spectrometer includes a second chamber having a third end and a fourth end configured such that a fluid may flow in a second direction from the third end to the fourth end, and a second electrode system that generates an asymmetric electric field within an interior of the second chamber. Additionally, the ion mobility spectrometer and the differential mobility spectrometer form an interface region. Also, the first end and the third end are positioned facing one another so that the constant electric field enters the third end and overlaps the fluid flowing in the second direction.

  7. Sensors for the Senses

    DEFF Research Database (Denmark)

    Brooks, Anthony Lewis

    2015-01-01

    -worn sensors (volumetric, linear and planar interface profiles). Mapping of sourced human data is to a variety of digital content including art-based (music making, digital painting, lighting effects), video games, Virtual Reality and robotic devices. System adaptability promotes participant profile matching e...... product and industry start-ups. At the core of the research is a rethinking in the way a human interacts with ICT. Current research explores a concept of dynamic air and alternative physical-virtual environments. Conclusions introduce a suggested need of increased researcher awareness of post......In his ACM Computers in Entertainment article, titled "Artist and Audience: Emerging the Nano-entertainment experience", the author posited on how Inhabited Information Spaces, created as core catalyst of research, may be questioned as a multisensory future virtual work of art. This themed Human...

  8. Miniature Biometric Sensor Project

    Science.gov (United States)

    Falker, John; Terrier, Douglas; Clayton, Ronald; Hanson, Andrea; Cooper, Tommy; Downs, Meghan; Flint, Stephanie; Reyna, Baraquiel; Simon, Cory; Wilt, Grier

    2015-01-01

    Heart rate monitoring (HRM) is a critical need during exploration missions. Unlike the four separate systems used on ISS today, the single HRM system should perform as a diagnostic tool, perform well during exercise or high level activity, and be suitable for use during EVA. Currently available HRM technologies are dependent on uninterrupted contact with the skin and are prone to data drop-out and motion artifact when worn in the spacesuit or during exercise. Here, we seek an alternative to the chest strap and electrode based sensors currently in use on ISS today. This project aims to develop a single, high performance, robust biosensor with focused efforts on improved heart rate data quality collection during high intensity activity such as exercise or EVA.

  9. Wireless SAW Interrogator and Sensor System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Wireless, passive, Surface Acoustic Wave (SAW), Orthogonal Frequency Coded (OFC) temperature sensors, operating in a multi-sensor environment, developed at the...

  10. Transonic Flight Smart Sensor Suite Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fiber optic sensors are rapidly emerging to replace conventional electrical-based sensor instrumentation in specific applications where small size, low mass,...

  11. Applications for wireless sensor networks : tracking with binary proximity sensors

    OpenAIRE

    Ruiz Fernández, Andoni

    2012-01-01

    El interés cada vez mayor por las redes de sensores inalámbricos pueden ser entendido simplemente pensando en lo que esencialmente son: un gran número de pequeños nodos sensores autoalimentados que recogen información o detectan eventos especiales y se comunican de manera inalámbrica, con el objetivo final de entregar sus datos procesados a una estación base. Los nodos sensores están densamente desplegados dentro del área de interés, se pueden desplegar al azar y tienen capacidad de cooper...

  12. EDITORIAL: Sensors and sensing systems

    Science.gov (United States)

    Dewhurst, Richard; Tian, Gui Yun

    2008-02-01

    Sensors are very important for measurement science and technology. They serve as a vital component in new measurement techniques and instrumentation systems. Key qualities of a good sensor system are high resolution, high reliability, low cost, appropriate output for a given input (good sensitivity), rapid response time, small random error in results, and small systematic error. Linearity is also useful, but with the advent of lookup tables and software, it is not as important as it used to be. In the last several years, considerable effort around the world has been devoted to a wide range of sensors from nanoscale sensors to sensor networks. Collectively, these vast and multidisciplinary efforts are developing important technological roadmaps to futuristic sensors with new modalities, significantly enhanced effectiveness and integrated functionality (data processing, computation, decision making and communications). When properly organized, they will have important relevance to life science and security applications, e.g. the sensing and monitoring of chemical, biological, radiological and explosive threats. A special feature in this issue takes a snapshot of some recent developments that were first presented at an international conference, the 2007 IEEE International Conference on Networking, Sensing and Control (ICNSC). The conference discussed recent developments, from which a few papers have since been brought together in this special feature. Gas sensing for environmental monitoring remains a topical subject, and two papers deal with this issue. One is concerned with the exploitation of nanostructured Au-doped cobalt oxyhydroxide-based carbon monoxide sensors for fire detection at its earlier stages (Zhuiykov and Dowling), whilst another examines the role of oxygen in high temperature hydrogen sulfide detection using MISiC sensors (Weng et al). Again for environmental monitoring, another paper deals with accurate sound source localization in a reverberant

  13. Applying Sensor Web Technology to Marine Sensor Data

    Science.gov (United States)

    Jirka, Simon; del Rio, Joaquin; Mihai Toma, Daniel; Nüst, Daniel; Stasch, Christoph; Delory, Eric

    2015-04-01

    In this contribution we present two activities illustrating how Sensor Web technology helps to enable a flexible and interoperable sharing of marine observation data based on standards. An important foundation is the Sensor Web Architecture developed by the European FP7 project NeXOS (Next generation Low-Cost Multifunctional Web Enabled Ocean Sensor Systems Empowering Marine, Maritime and Fisheries Management). This architecture relies on the Open Geospatial Consortium's (OGC) Sensor Web Enablement (SWE) framework. It is an exemplary solution for facilitating the interoperable exchange of marine observation data within and between (research) organisations. The architecture addresses a series of functional and non-functional requirements which are fulfilled through different types of OGC SWE components. The diverse functionalities offered by the NeXOS Sensor Web architecture are shown in the following overview: - Pull-based observation data download: This is achieved through the OGC Sensor Observation Service (SOS) 2.0 interface standard. - Push-based delivery of observation data to allow users the subscription to new measurements that are relevant for them: For this purpose there are currently several specification activities under evaluation (e.g. OGC Sensor Event Service, OGC Publish/Subscribe Standards Working Group). - (Web-based) visualisation of marine observation data: Implemented through SOS client applications. - Configuration and controlling of sensor devices: This is ensured through the OGC Sensor Planning Service 2.0 interface. - Bridging between sensors/data loggers and Sensor Web components: For this purpose several components such as the "Smart Electronic Interface for Sensor Interoperability" (SEISI) concept are developed; this is complemented by a more lightweight SOS extension (e.g. based on the W3C Efficient XML Interchange (EXI) format). To further advance this architecture, there is on-going work to develop dedicated profiles of selected OGC

  14. Aprendizagem como/na prática

    OpenAIRE

    Jean Lave

    2015-01-01

    ResumoEste artigo considera como o estudo da cultura e da aprendizagem pode ser de particular relevância para o campo da antropologia sociocultural em geral. O termo mais importante na expressão “cultura & aprendizagem” talvez seja o logograma “&” – ou seja, coloca-se a questão sobre o que conecta cultura e aprendizagem, perguntando-se como esses termos estão relacionados. Como devemos compreender cultura e aprendizagem como instâncias produtoras delas próprias, e uma da outra, na prática? Re...

  15. Vertically stacked nanocellulose tactile sensor.

    Science.gov (United States)

    Jung, Minhyun; Kim, Kyungkwan; Kim, Bumjin; Lee, Kwang-Jae; Kang, Jae-Wook; Jeon, Sanghun

    2017-11-16

    Paper-based electronic devices are attracting considerable attention, because the paper platform has unique attributes such as flexibility and eco-friendliness. Here we report on what is claimed to be the firstly fully integrated vertically-stacked nanocellulose-based tactile sensor, which is capable of simultaneously sensing temperature and pressure. The pressure and temperature sensors are operated using different principles and are stacked vertically, thereby minimizing the interference effect. For the pressure sensor, which utilizes the piezoresistance principle under pressure, the conducting electrode was inkjet printed on the TEMPO-oxidized-nanocellulose patterned with micro-sized pyramids, and the counter electrode was placed on the nanocellulose film. The pressure sensor has a high sensitivity over a wide range (500 Pa-3 kPa) and a high durability of 10(4) loading/unloading cycles. The temperature sensor combines various materials such as poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS), silver nanoparticles (AgNPs) and carbon nanotubes (CNTs) to form a thermocouple on the upper nanocellulose layer. The thermoelectric-based temperature sensors generate a thermoelectric voltage output of 1.7 mV for a temperature difference of 125 K. Our 5 × 5 tactile sensor arrays show a fast response, negligible interference, and durable sensing performance.

  16. Infrasound Sensor Models and Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    KROMER,RICHARD P.; MCDONALD,TIMOTHY S.

    2000-07-31

    Sandia National Laboratories has continued to evaluate the performance of infrasound sensors that are candidates for use by the International Monitoring System (IMS) for the Comprehensive Nuclear-Test-Ban Treaty Organization. The performance criteria against which these sensors are assessed are specified in ``Operational Manual for Infra-sound Monitoring and the International Exchange of Infrasound Data''. This presentation includes the results of efforts concerning two of these sensors: (1) Chaparral Physics Model 5; and (2) CEA MB2000. Sandia is working with Chaparral Physics in order to improve the capability of the Model 5 (a prototype sensor) to be calibrated and evaluated. With the assistance of the Scripps Institution of Oceanography, Sandia is also conducting tests to evaluate the performance of the CEA MB2000. Sensor models based on theoretical transfer functions and manufacturer specifications for these two devices have been developed. This presentation will feature the results of coherence-based data analysis of signals from a huddle test, utilizing several sensors of both types, in order to verify the sensor performance.

  17. Particle fallout/activity sensor

    Science.gov (United States)

    Curtis, Ihlefeld M. (Inventor); Youngquist, Robert C. (Inventor); Moerk, John S. (Inventor); Rose, Kenneth A., III (Inventor)

    1995-01-01

    A particle fallout/activity sensor measures relative amounts of dust or other particles which collect on a mirror in an area to be monitored. The sensor includes a sensor module and a data acquisition module, both of which can be operated independently of one another or in combination with one another. The sensor module includes a housing containing the mirror, an LED assembly for illuminating the mirror and an optical detector assembly for detecting light scattered off of the mirror by dust or other particles collected thereon. A microprocessor controls operation of the sensor module's components and displays results of a measurement on an LCD display mounted on the housing. A push button switch is also mounted on the housing which permits manual initiation of a measurement. The housing is constructed of light absorbing material, such as black delrin, which minimizes detection of light by the optical detector assembly other than that scattered by dust or particles on the mirror. The data acquisition module can be connected to the sensor module and includes its own microprocessor, a timekeeper and other digital circuitry for causing the sensor module to make a measurement periodically and send the measurement data to the data acquisition module for display and storage in memory for later retrieval and transfer to a separate computer. The time tagged measurement data can also be used to determine the relative level of activity in the monitored area since this level is directly related to the amount of dust or particle fallout in the area.

  18. Teste tuberculínico. Como optimizar?

    Directory of Open Access Journals (Sweden)

    Raquel Duarte

    2009-03-01

    Full Text Available Resumo: Os testes utilizados no diagnóstico de infecção latente pelo Mycobacterium tuberculosis, o teste tuberculínico e o doseamento do interferão gama (IGRA identificam a existência de uma resposta imunológica adaptativa de memória contra os antigénios micobacterianos. Considerando as limitações dos dois testes, a melhor solução passa por tirar proveito das melhores características de cada um. A maior parte dos autores concorda com a utilização dos dois testes, utilizando os IGRA sobretudo na confirmação da positividade do teste tuberculínico (tirando proveito da sua maior especificidade.As características operativas do teste tuberculínico dependem da prevalência da doença na comunidade e dos objectivos da sua realização (as suas características são superiores quando utilizada no âmbito de rastreio ou como teste diagnóstico. Para interpretar correctamente um teste tuberculínico, o clínico deve conhecer a epidemiologia da tuberculose na comunidade e definir correctamente as indicações para a sua realização. Abstract: The tests used in the diagnosis of tuberculosis latent infection, the tuberculin skin test (TST and the interferon-gamma assays (IGRA, identify the existence of an adaptive immune response towards mycobacterial antigens. Considering the limitations of the two tests, the best solution is to take advantage of the best characteristics of each one. Most of the authors agree to the use of the two tests, using the IGRAS in the confirmation of a positive TST (because of its higher specificity. The operative characteristics of TST depend on the prevalence of the illness in the community and the aim of its use (its operative characteristics are higher when used in the tracing scope or as a diagnostic test. To interpret correctly a TST, the physician must know the epidemiology of tuberculosis in the community and correctly define the indications for its use. Palavras-chave: Tuberculose, teste tubercul

  19. O direito como juízo

    Directory of Open Access Journals (Sweden)

    Denise Maria Weiss de Paula Machado

    1988-07-01

    Full Text Available This study presents a synthetic and personal view of the consequences arising from the notion of law as justice. For Kelsen, in this "Theory of pure law", human conduct produce facts, justly or injust1y, that become characterized as legal norms. Human behavior is determined by acts of reason, that are defined by a representative (a judge, and then are used as valid norms of justice. The conception of law is, therefore, represented by an ideal object, rational and only apprehensible through abstract processes, following the views of Kelsenians. Without any intent to criticize the "great master of Vienna", a search of the text demonstrates that a neutral ideology, concerning the comprehension and application of law, does not and can not exists law can not depart from empirical reality when following its purpose of promoting the liberty and development of society.O presente texto tem por finalidade apresentar uma visão sintética e pessoal das conseqüências decorrentes da noção do direito como juízo. Para KELSEN, em sua "Teoria pura do direito", a conduta humana produz fatos jurídicos ou injurídicos, conforme assim os caracterizam as normas jurídicas. A conduta humana é determinada por uma razão de agir, que é definida pela representação juízo que o homem tem da norma jurídica 'vigente. A concepção do direito é, pois, representada por um objeto ideal, racional e somente apreensível através de um processo de abstração, segundo a visão Kelseniana. Sem a mínima pretensão de formular críticas ao grande Mestre de Viena, procura o texto demonstrar que a neutralidade ideológica, para a compreensão e aplicação do direito, não existe e nem pode existir, eis que o direito não pode se afastar da realidade empírica, a fim de que possa alcançar sua finalidade de promover a libertação e a evolução da sociedade.

  20. Sensoriamento remoto como subsídio à modelagem do balanço energético superficial

    Directory of Open Access Journals (Sweden)

    Vassiliki Terezinha Galvão Boulomytis

    2010-09-01

    Full Text Available O balanço energético superficial interfere no funcionamento do sistema terrestre através da relação existente entre a água e a energia solar e do modo como ocorre o seu processo de partição. Para a sua estimativa, modelagens vêm sendo realizadas utilizando-se de um ou mais sensores com diferentes resoluções, a fim de se obter dados com resoluções temporal e espacial adequadas a uma escala local. Neste estudo serão apresentados modelos para estimar a evapotranspiração e outros parâmetros biofísicos através do balanço energético superficial com a utilização dos sensores MODIS e AMSR-E.

  1. RSS-based sensor localization in underwater acoustic sensor networks

    NARCIS (Netherlands)

    Xu, T.; Hu, Y.; Zhang, Bingbing; Leus, G.J.T.; Dong, Min; Zheng, Thomas Fang

    2016-01-01

    Since the global positioning system (GPS) is not applicable underwater, source localization using wireless sensor networks (WSNs) is gaining popularity in oceanographic applications. Unlike terrestrial WSNs (TWSNs) which uses electromagnetic signaling, underwater WSNs (UWSNs) require underwater

  2. Target Coverage in Wireless Sensor Networks with Probabilistic Sensors

    Science.gov (United States)

    Shan, Anxing; Xu, Xianghua; Cheng, Zongmao

    2016-01-01

    Sensing coverage is a fundamental problem in wireless sensor networks (WSNs), which has attracted considerable attention. Conventional research on this topic focuses on the 0/1 coverage model, which is only a coarse approximation to the practical sensing model. In this paper, we study the target coverage problem, where the objective is to find the least number of sensor nodes in randomly-deployed WSNs based on the probabilistic sensing model. We analyze the joint detection probability of target with multiple sensors. Based on the theoretical analysis of the detection probability, we formulate the minimum ϵ-detection coverage problem. We prove that the minimum ϵ-detection coverage problem is NP-hard and present an approximation algorithm called the Probabilistic Sensor Coverage Algorithm (PSCA) with provable approximation ratios. To evaluate our design, we analyze the performance of PSCA theoretically and also perform extensive simulations to demonstrate the effectiveness of our proposed algorithm. PMID:27618902

  3. New sensors and processing chain

    CERN Document Server

    Yaakoubi, Nourdin

    2014-01-01

    A vital tool for researchers, engineers, and students, New Sensors and Processing Chain focuses on the processing chain to set up in order to extract relevant information on various systems. Highlighting the design of new microsensors and various applications, the authors present recent progress in instrumentation and microsystem design, providing insight to the modification of the sensor itself as well as its environment. Various applications illustrate the presentations, which show how a processing chain is organized from the data acquired by a specific sensor.

  4. Biological and medical sensor technologies

    CERN Document Server

    Iniewski, Krzysztof

    2012-01-01

    Biological and Medical Sensor Technologies presents contributions from top experts who explore the development and implementation of sensors for various applications used in medicine and biology. Edited by a pioneer in the area of advanced semiconductor materials, the book is divided into two sections. The first part covers sensors for biological applications. Topics include: Advanced sensing and communication in the biological world DNA-derivative architectures for long-wavelength bio-sensing Label-free silicon photonics Quartz crystal microbalance-based biosensors Lab-on-chip technologies fo

  5. Photonic E-field sensor

    Directory of Open Access Journals (Sweden)

    A. A. Savchenkov

    2014-12-01

    Full Text Available We report on both theoretical and experimental studies of a photonic implementation of the electric (E- field sensor using a probe made with all-dielectric RF-transparent elements. The geometrical dimensions of the electric field probe can be smaller than the wavelength of the measured electromagnetic field in the material. Our theoretical calculations show that the sensor allows detecting electric fields in a broad frequency range (100 Hz-20 GHz with sensitivity better than 1 μV/[Hz1/2 m]. We demonstrate the sensor operating at X-band and validate the theoretical predictions.

  6. UAV sensor and survivability issues

    Energy Technology Data Exchange (ETDEWEB)

    Canavan, G.H.

    1996-07-01

    This report discusses the most significant tradeoffs between the operating altitude and the complexity and cost of UAVs and sensors. Low altitudes allow less complex, smaller sensors and platforms, but are vulnerable to ground fire. High altitudes require more numerous and capable sensors, but provide wider swaths for more rapid coverage and reduced vulnerability to ground fire. It is shown that for mission requirements and air defenses that higher is not necessarily better and that optimal flight altitudes exist that can be determined analytically.

  7. Recent Advances in Plasmonic Sensors

    Directory of Open Access Journals (Sweden)

    Lianming Tong

    2014-05-01

    Full Text Available Plasmonic sensing has been an important multidisciplinary research field and has been extensively used in detection of trace molecules in chemistry and biology. The sensing techniques are typically based on surface-enhanced spectroscopies and surface plasmon resonances (SPRs. This review article deals with some recent advances in surface-enhanced Raman scattering (SERS sensors and SPR sensors using either localized surface plasmon resonances (LSPRs or propagating surface plasmon polaritons (SPPs. The advances discussed herein present some improvements in SERS and SPR sensing, as well as a new type of nanowire-based SPP sensor.

  8. Electrodes for Semiconductor Gas Sensors

    Science.gov (United States)

    Lee, Sung Pil

    2017-01-01

    The electrodes of semiconductor gas sensors are important in characterizing sensors based on their sensitivity, selectivity, reversibility, response time, and long-term stability. The types and materials of electrodes used for semiconductor gas sensors are analyzed. In addition, the effect of interfacial zones and surface states of electrode–semiconductor interfaces on their characteristics is studied. This study describes that the gas interaction mechanism of the electrode–semiconductor interfaces should take into account the interfacial zone, surface states, image force, and tunneling effect. PMID:28346349

  9. Optical wheel-rotation sensor

    Science.gov (United States)

    Veeser, Lynn R.; Rodriguez, Patrick A.; Forman, Peter; Deeter, Merritt N.

    1994-09-01

    We describe a fiber-optic rotation sensor being developed for anti-lock braking systems. The basis of the sensor is the magneto-optic detection of the magnetic fields generated by a wheel of alternating magnetized magnets fixed to a wheel of the automobile. Highly sensitive iron garnet crystals serve as the magneto-optic sensing elements. For films with perpendicularly- magnetized domains, the domain structure produces diffraction which is magnetic-field dependent. Exploitation of this effect permits the construction of magneto-optic magnetic field sensors requiring no polarization elements or lenses.

  10. Embedded sensors in layered manufacturing

    Science.gov (United States)

    Li, Xiaochun

    Layered Manufacturing can be applied to build ``smart'' parts with sensors, integrated circuits, and actuators placed within the component. Embedded sensors can be used to gain data for validating or improving designs during the prototype stage or to obtain information on the performance and structural integrity of components in service. Techniques for embedding fiber optic sensors in metals, polymers, and ceramics have been investigated. Embedding optical fibers into metals is especially challenging because engineering alloys tend to exhibit high melting temperatures. In the present research an embedding sequence was developed capable of embedding fiber sensors into parts made of metal alloys with high melting temperatures. Fiber Bragg Grating (FBG) sensors were selected as the most promising sensor candidate. The embedded FBG sensors were characterized for temperature and strain measurements. The embedded FBG sensors in nickel and stainless steel provided high sensitivity, good accuracy, and high temperature capacity for temperature measurements. Temperature sensitivity approximately 100% higher than that of bare FBGs was demonstrated. For strain measurements, the sensors embedded in metal and polyurethane yielded high sensitivity, accuracy, and linearity. The sensitivity of the embedded FBGs was in good agreement with that of bare FBGs. Moreover, a decoupling technique for embedded FBG sensors was developed to separate temperature and strain effects. The embedded FBG sensors were used to monitor the accumulation of residual stresses during the laser- assisted Layered Manufacturing, to measure the strain field in layered materials, to measure pressure, and to monitor temperature and strain simultaneously. New techniques have been developed for temperature and strain measurements of rotating components with FBG sensors embedded or attached to the surface. Tunable laser diodes were incorporated into the sensing system for monitoring the Bragg grating wavelength

  11. Next generation sensors and systems

    CERN Document Server

    2016-01-01

    Written by experts in their area of research, this book has outlined the current status of the fundamentals and analytical concepts, modelling and design issues, technical details and practical applications of different types of sensors and discussed about the trends of next generation of sensors and systems happening in the area of Sensing technology. This book will be useful as a reference book for engineers and scientist especially the post-graduate students find will this book as reference book for their research on wearable sensors, devices and technologies.  .

  12. Electrochemical Sensors for Clinic Analysis

    Directory of Open Access Journals (Sweden)

    Guang Li

    2008-03-01

    Full Text Available Demanded by modern medical diagnosis, advances in microfabrication technology have led to the development of fast, sensitive and selective electrochemical sensors for clinic analysis. This review addresses the principles behind electrochemical sensor design and fabrication, and introduces recent progress in the application of electrochemical sensors to analysis of clinical chemicals such as blood gases, electrolytes, metabolites, DNA and antibodies, including basic and applied research. Miniaturized commercial electrochemical biosensors will form the basis of inexpensive and easy to use devices for acquiring chemical information to bring sophisticated analytical capabilities to the non-specialist and general public alike in the future.

  13. Organic semiconductors in sensor applications

    CERN Document Server

    Malliaras, George; Owens, Róisín

    2008-01-01

    Organic semiconductors offer unique characteristics such as tunability of electronic properties via chemical synthesis, compatibility with mechanically flexible substrates, low-cost manufacturing, and facile integration with chemical and biological functionalities. These characteristics have prompted the application of organic semiconductors and their devices in physical, chemical, and biological sensors. This book covers this rapidly emerging field by discussing both optical and electrical sensor concepts. Novel transducers based on organic light-emitting diodes and organic thin-film transistors, as well as systems-on-a-chip architectures are presented. Functionalization techniques to enhance specificity are outlined, and models for the sensor response are described.

  14. Perancangan Sistem Sensor Pemonitor Lingkungan Berbasis Jaringan Sensor Nirkabel

    Directory of Open Access Journals (Sweden)

    Nurhuda Maulana

    2016-04-01

    Full Text Available Air pollution is a problem that get a lot of people’s attention, especially at campus environment. It is evocate the stakeholder of campus to monitor the environmental conditions at the campus which themed a green campus. Advances in science and technology, especially in computer and embedded systems in principle can be applied to solve this problem. There are creating an application system that is equipped with sensor to monitor the air quality level wirelessly. The system supports several environmental monitoring sensors that are connected in a wireless sensor network. The objective of this research was to design and create a sensor system that can monitor environment condition quantity by providing the appropriate output value. Sensors that used to read the air quality parameters is TGS 2600 to read the gas concentration of carbon monoxide (CO, TGS 2201 for nitrogen dioxide (NO2, GP2Y1010AU0F for particulate matter, BH1750 for light ambient, and SHT11 for humidity and temperature. This sensor system using Arduino board that based on Atmega 2560 microcontroller. This system is equipped with RTC as a time and GPS as a coordinate where the sensor system is placed as a node. The result of this reseach is the system able to read parameters as air quality monitoring well. The error reading in this sensor system is 0.69 ppm CO gas, 2.8 lx on the intensity of light, 0.22 C in temperature reading, and 0.98% in humidity readings.

  15. Sensor anomaly detection in wireless sensor networks for healthcare.

    Science.gov (United States)

    Haque, Shah Ahsanul; Rahman, Mustafizur; Aziz, Syed Mahfuzul

    2015-04-15

    Wireless Sensor Networks (WSN) are vulnerable to various sensor faults and faulty measurements. This vulnerability hinders efficient and timely response in various WSN applications, such as healthcare. For example, faulty measurements can create false alarms which may require unnecessary intervention from healthcare personnel. Therefore, an approach to differentiate between real medical conditions and false alarms will improve remote patient monitoring systems and quality of healthcare service afforded by WSN. In this paper, a novel approach is proposed to detect sensor anomaly by analyzing collected physiological data from medical sensors. The objective of this method is to effectively distinguish false alarms from true alarms. It predicts a sensor value from historic values and compares it with the actual sensed value for a particular instance. The difference is compared against a threshold value, which is dynamically adjusted, to ascertain whether the sensor value is anomalous. The proposed approach has been applied to real healthcare datasets and compared with existing approaches. Experimental results demonstrate the effectiveness of the proposed system, providing high Detection Rate (DR) and low False Positive Rate (FPR).

  16. Wireless sensors and sensor networks for homeland security applications.

    Science.gov (United States)

    Potyrailo, Radislav A; Nagraj, Nandini; Surman, Cheryl; Boudries, Hacene; Lai, Hanh; Slocik, Joseph M; Kelley-Loughnane, Nancy; Naik, Rajesh R

    2012-11-01

    New sensor technologies for homeland security applications must meet the key requirements of sensitivity to detect agents below risk levels, selectivity to provide minimal false-alarm rates, and response speed to operate in high throughput environments, such as airports, sea ports, and other public places. Chemical detection using existing sensor systems is facing a major challenge of selectivity. In this review, we provide a brief summary of chemical threats of homeland security importance; focus in detail on modern concepts in chemical sensing; examine the origins of the most significant unmet needs in existing chemical sensors; and, analyze opportunities, specific requirements, and challenges for wireless chemical sensors and wireless sensor networks (WSNs). We further review a new approach for selective chemical sensing that involves the combination of a sensing material that has different response mechanisms to different species of interest, with a transducer that has a multi-variable signal-transduction ability. This new selective chemical-sensing approach was realized using an attractive ubiquitous platform of battery-free passive radio-frequency identification (RFID) tags adapted for chemical sensing. We illustrate the performance of RFID sensors developed in measurements of toxic industrial materials, humidity-independent detection of toxic vapors, and detection of chemical-agent simulants, explosives, and strong oxidizers.

  17. LA MUNDIALIZACIÓN DEL DARWINISMO COMO PROCESO Y COMO TEXTO

    Directory of Open Access Journals (Sweden)

    OLGA RESTREPO FORERO

    2009-01-01

    Full Text Available El fenómeno de la difusión del darwinismo ha sido ampliamente estudiado. No solo existe una “industria de Darwin” que se ha ocupado de investigar cómo se produjo la obra de Darwin, sino que también existe una “industria de la difusión del darwinismo”, que investiga los procesos de recepción del darwinismo en diversas partes del mundo. En el artículo se cuestiona la separación entre los estudios que examinan la producción del origen de las especies y los que tratan de su posterior difusión, considerados como procesos completamente independientes. Con base en unos pocos ejemplos, se muestra cómo Darwin fue produciendo y modificando su obra a partir de las contribuciones que fue recogiendo alrededor del mundo y a partir de las respuestas que fue recibiendo a medida que su obra era comentada y discutida. Finalmente se examina cómo, al estudiar la mundialización del darwinismo surge el problema de definir el fenómeno bajo estudio, si con una perspectiva normativa, que imponga un orden en la proliferación de sentidos que surge como consecuencia de la expansión, o con una perspectiva no esencialista que más bien sitúe al darwinismo en relación con sus diferentes usos y apropiaciones locales.

  18. El humanismo como paradigma de la enfermería como ciencia

    Directory of Open Access Journals (Sweden)

    Núñez Gómez Nicolás Arturo

    1999-12-01

    Full Text Available

    Humanism's philosophical conception is presented to development a paradigm of nursing science. The nursing from creation has been guided toward professional practice and category; of Care has been fundamental contribution. In this article our intends is to grow some fine general of reflection so that nurses contribute to development of a science called nursing and whose accent is man in their multiple dimensions.

    A partir del humanismo como concepción filosófica se presenta una propuesta para crear un paradigma de la enfermería como ciencia. Desde su creación, la enfermería se ha orientado hacia su práctica profesional y la categoría de cuidado ha sido su aporte fundamental. Este artículo se propone crear unas líneas generales de reflexión, para que las enfermeras aporten al desarrollo de una ciencia llamada enfermería y cuyo acento es el hombre en sus múltiples dimensiones.

  19. Redes de sensores inalámbricos : Trabajo Fin de Grado

    OpenAIRE

    Roca González, Francisco Javier

    2015-01-01

    [ES]Desarrolla el control de los parámetros fundamentales de una instalación fotovoltaica, un huerto urbano así como las características de las placas necesarias para poder conocer estado y rendimiento permitiendo la monitorización utilizando un sistema de National Instruments basado en la programación gráfica de LabView y CompactRio, sistema encargado de recoger la información de módulos WSN (Wireless Sensor Network) conectados directamente a termorresistencias, sensores de temperatura, hum...

  20. MEMS climate sensor for crops in greenhouses

    DEFF Research Database (Denmark)

    Birkelund, Karen; Jensen, Kim Degn; Højlund-Nielsen, Emil

    2010-01-01

    We have developed and fabricated a multi-sensor chip for greenhouse applications and demonstrated the functionality under controlled conditions. The sensor consists of a humidity sensor, temperature sensor and three photodiodes sensitive to blue, red and white light, respectively. The humidity se...

  1. Hybrid integrated electro-optic sensor platform

    NARCIS (Netherlands)

    Krijger, A.J.T. de; Benoist, K.W.; Bezooijen, J.A.G. van; Bekman, H.H.P.T.

    1998-01-01

    Optical sensors are an important class of sensors. They can offer high sensitivity, high electromagnetic immunity and compactness. An important sub-class is formed by the fiber-optic based sensors. They are used among others for smart structures, where the fiber is used in a distributed sensor

  2. Contactless EMG sensors embroidered into textile

    OpenAIRE

    Linz, Torsten; Gourmelon, L.; Langereis, G.

    2007-01-01

    To obtain maximum unobtrusiveness with sensors for monitoring health parameters on the human body, two technical solutions are combined. First we propose contactless sensors for capacitive electromyography measurements. Secondly, the sensors are integrated into textile, so complete fusion with a wearable garment is enabled. We are presenting the first successful measurements with such sensors.

  3. Synchronizing data from irregularly sampled sensors

    Science.gov (United States)

    Uluyol, Onder

    2017-07-11

    A system and method include receiving a set of sampled measurements for each of multiple sensors, wherein the sampled measurements are at irregular intervals or different rates, re-sampling the sampled measurements of each of the multiple sensors at a higher rate than one of the sensor's set of sampled measurements, and synchronizing the sampled measurements of each of the multiple sensors.

  4. Online digital compensation method for AMR sensors

    NARCIS (Netherlands)

    Zambrano Constantini, A.C.; Kerkhoff, Hans G.

    Anisotropic Magnetoresistance (AMR) sensors are magnetic sensors often used for angle measurements. The sensor outputs should be two perfect sinusoidal signals that depend on the angle to be measured. However due to non-ideal properties of the sensor, the actual outputs include undesired parameters

  5. Ammonia sensors and their applications - a review

    NARCIS (Netherlands)

    Timmer, B.H.; Olthuis, Wouter; van den Berg, Albert

    Many scientific papers have been written concerning gas sensors for different sensor applications using several sensing principles. This review focuses on sensors and sensor systems for gaseous ammonia. Apart from its natural origin, there are many sources of ammonia, like the chemical industry or

  6. Optimal sensor configuration for complex systems

    DEFF Research Database (Denmark)

    Sadegh, Payman; Spall, J. C.

    1998-01-01

    configuration is based on maximizing the overall sensor response while minimizing the correlation among the sensor outputs. The procedure for sensor configuration is based on simultaneous perturbation stochastic approximation (SPSA). SPSA avoids the need for detailed modeling of the sensor response by simply...

  7. Wearable Flexible Sensors: A Review

    KAUST Repository

    Nag, Anindya

    2017-05-18

    The paper provides a review on some of the significant research work done on wearable flexible sensors (WFS). Sensors fabricated with flexible materials have been attached to a person along with the embedded system to monitor a parameter and transfer the significant data to the monitoring unit for further analyses. The use of wearable sensors has played a quite important role to monitor physiological parameters of a person to minimize any malfunctioning happening in the body. The paper categorizes the work according to the materials used for designing the system, the network protocols and different types of activities that were being monitored. The challenges faced by the current sensing systems and future opportunities for the wearable flexible sensors regarding its market values are also briefly explained in the paper.

  8. Methane Liquid Level Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced Technologies Group, Inc. proposes the development of a Methane Liquid-Level Sensor, (MLS) for In-Space cryogenic storage capable of continuous monitoring of...

  9. Wireless Sensor Portal Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Mobitrum Corporation has demonstrated the feasibility in the Phase I of " A Wireless Sensor Portal Technology" and proposes a Phase II effort to develop a wireless...

  10. Cryogenic MEMS Pressure Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A directly immersible cryogenic MEMS pressure sensor will be developed. Each silicon die will contain a vacuum-reference and a tent-like membrane. Offsetting thermal...

  11. Chemical sensors for space applications

    Science.gov (United States)

    Bonting, Sjoerd L.

    1992-01-01

    The payload of the Space Station Freedom will include sensors for frequent monitoring of the water recycling process and for measuring the many biochemical parameters related to onboard experiments. This paper describes the sensor technologies and the types of transducers and selectors considered for these sensors. Particular attention is given to such aspects of monitoring of the water recycling process as the types of water use, the sources of water and their hazards, the sensor systems for monitoring, microbial monitoring, and monitoring toxic metals and organics. An approach for monitoring water recycling is suggested, which includes microbial testing with a potentiometric device (which should be in first line of tests), the use of an ion-selective electrode for inorganic ion determinations, and the use of optic fiber techniques for the determination of total organic carbon.

  12. Microfiber optical sensors: a review.

    Science.gov (United States)

    Lou, Jingyi; Wang, Yipei; Tong, Limin

    2014-03-25

    With diameter close to or below the wavelength of guided light and high index contrast between the fiber core and the surrounding, an optical microfiber shows a variety of interesting waveguiding properties, including widely tailorable optical confinement, evanescent fields and waveguide dispersion. Among various microfiber applications, optical sensing has been attracting increasing research interest due to its possibilities of realizing miniaturized fiber optic sensors with small footprint, high sensitivity, fast response, high flexibility and low optical power consumption. Here we review recent progress in microfiber optical sensors regarding their fabrication, waveguide properties and sensing applications. Typical microfiber-based sensing structures, including biconical tapers, optical gratings, circular cavities, Mach-Zehnder interferometers and functionally coated/doped microfibers, are summarized. Categorized by sensing structures, microfiber optical sensors for refractive index, concentration, temperature, humidity, strain and current measurement in gas or liquid environments are reviewed. Finally, we conclude with an outlook for challenges and opportunities of microfiber optical sensors.

  13. Microfiber Optical Sensors: A Review

    Directory of Open Access Journals (Sweden)

    Jingyi Lou

    2014-03-01

    Full Text Available With diameter close to or below the wavelength of guided light and high index contrast between the fiber core and the surrounding, an optical microfiber shows a variety of interesting waveguiding properties, including widely tailorable optical confinement, evanescent fields and waveguide dispersion. Among various microfiber applications, optical sensing has been attracting increasing research interest due to its possibilities of realizing miniaturized fiber optic sensors with small footprint, high sensitivity, fast response, high flexibility and low optical power consumption. Here we review recent progress in microfiber optical sensors regarding their fabrication, waveguide properties and sensing applications. Typical microfiber-based sensing structures, including biconical tapers, optical gratings, circular cavities, Mach-Zehnder interferometers and functionally coated/doped microfibers, are summarized. Categorized by sensing structures, microfiber optical sensors for refractive index, concentration, temperature, humidity, strain and current measurement in gas or liquid environments are reviewed. Finally, we conclude with an outlook for challenges and opportunities of microfiber optical sensors.

  14. Sensor technology for smart structures

    Science.gov (United States)

    Rogowski, R. S.; Heyman, J. S.; Holben, M. S., Jr.; Dehart, D. W.; Doederlein, T.

    1989-01-01

    Advanced aerospace structures are discussed that will very likely be fabricated with integral sensors, actuators, and microprocessors for monitoring and dynamic control of configuration. The concept of 'smart structures' integrates fiber-optic sensor technology with advanced composite materials, whereby the optical fibers are embedded in a composite material and provide internal sensing capability for monitoring parameters which are important for the safety, performance, and reliability of the material and the structure. Along with other research facilities, NASA has initiated a cooperative program to design, fabricate, and test composite trusses, tubes, and flat panels with embedded optical fibers for testing and developing prototype smart structures. It is shown that fiber-optic sensor technology can be combined with advanced material and structure concepts to produce a new class of materials with internal sensors for health monitoring of structures.

  15. Virtual Sensor Test Instrumentation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Mobitrum has started the development of virtual sensor test instrumentation in Phase I for characterization and measurement of ground testing of propulsion systems....

  16. Vehicle classification using mobile sensors.

    Science.gov (United States)

    2013-04-01

    In this research, the feasibility of using mobile traffic sensors for binary vehicle classification on arterial roads is investigated. Features (e.g. : speed related, acceleration/deceleration related, etc.) are extracted from vehicle traces (passeng...

  17. Miniature Airborne Methane Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — KalScott Engineering, and the subcontractor, Princeton University propose the development and demonstration of compact and robust methane sensor for small Unmanned...

  18. Effectiveness of passive alcohol sensors

    Science.gov (United States)

    1996-03-01

    Author's abstract: The purpose of this study was to evaluate the effectiveness of passive alcohol sensors for youth alcohol enforcement conducted as part of normal or typical police operations. Three municipal police departments of 100 or more sworn ...

  19. Analytical design of multispectral sensors

    Science.gov (United States)

    Wiersma, D. J.; Landgrebe, D. A.

    1980-01-01

    An optimal design based on the criterion of minimum mean square representation error using the Karhunen-Loeve expansion was developed to represent the spectral response functions from a stratum based upon a stochastic process scene model. From the overall pattern recognition system perspective, the effect of the representation accuracy on a typical performance criterion (the probability of correct classification) is investigated. The optimum sensor design provides a standard against which practical (suboptimum) operational sensors can be compared. An example design is provided and its performance is illustrated. Although developed primarily for the purpose of sensor design, the procedure has potential for making important contributions to scene understanding. Spectral channels which have narrow bandwidths relative to current sensor systems may be necessary to provide adequate spectral representation and improved classification performance.

  20. Universal Smart Sensor Interface Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Ground testing of propulsion systems requires highly accurate and precise sensor systems. Setting up such systems can be more time consuming than the test. The...

  1. A Cryogenic Flow Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Based on the success of the phase I effort, Advanced Technologies Group, Inc. proposes the development of a Cryogenic Flow Sensor (CFS) for determining mass flow of...

  2. Optical Landing Hazard Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Visidyne proposes to investigate an active optical 3D imaging LADAR as the sensor for an automated Landing Hazard Avoidance system for spacecraft landing on the Moon...

  3. Hydrocarbon Leak Detection Sensor Project

    Data.gov (United States)

    National Aeronautics and Space Administration — FTT is proposing the development of a sensor to detect the presence of hydrocarbons in turbopump Inter-Propellant Seals (IPS). The purpose of the IPS is to prevent...

  4. Introduction to wireless sensor networks

    CERN Document Server

    Forster, Anna

    2016-01-01

    Explores real-world wireless sensor network development, deployment, and applications. The book begins with an introduction to wireless sensor networks and their fundamental concepts. Hardware components, operating systems, protocols, and algorithms that make up the anatomy of a sensor node are described in chapter two. Properties of wireless communications, medium access protocols, wireless links, and link estimation protocols are described in chapter three and chapter four. Routing basics and metrics, clustering techniques, time synchronization and localization protocols, as well as sensing techniques are introduced in chapter five to nine. The concluding chapter summarizes the learnt methods and shows how to use them to deploy real-world sensor networks in a structured way.

  5. Unified broadcast in sensor networks

    DEFF Research Database (Denmark)

    Hansen, Morten Tranberg; Jurdak, Raja; Kusy, Branislav

    2011-01-01

    Complex sensor network applications include multiple services such as collection, dissemination, time synchronization, and failure detection protocols. Many of these protocols require local state maintenance through periodic broadcasts which leads to high control overhead. Recent attempts...

  6. Fiber optic hydrogen sensor

    Science.gov (United States)

    Buchanan, B.R.; Prather, W.S.

    1991-01-01

    Apparatus and method for detecting a chemical substance by exposing an optic fiber having a core and a cladding to the chemical substance so that the chemical substance can be adsorbed onto the surface of the cladding. The optic fiber is coiled inside a container having a pair of valves for controlling the entrance and exit of the substance. Light from a light source is received by one end of the optic fiber, preferably external to the container, and carried by the core of the fiber. Adsorbed substance changes the transmissivity of the fiber as measured by a spectrophotometer at the other end, also preferably external to the container. Hydrogen is detected by the absorption of infrared light carried by an optic fiber with a silica cladding. Since the adsorption is reversible, a sensor according to the present invention can be used repeatedly. Multiple positions in a process system can be monitored using a single container that can be connected to each location to be monitored so that a sample can be obtained for measurement, or, alternatively, containers can be placed near each position and the optic fibers carrying the partially-absorbed light can be multiplexed for rapid sequential reading, by a single spectrophotometer.

  7. Nanomaterials and Chemical Sensors

    Directory of Open Access Journals (Sweden)

    Sukumar BASU

    2011-11-01

    Full Text Available Nanomaterials and nanosensors are two most important iconic words of the modern science & Technology. Though nano technology is relatively a new area of research & development it will soon be included in the most modern electronic circuitry used for advanced computing systems. Since it will provide the potential link between the nanotechnology and the macroscopic world the development is primarily directed towards exploitation of nanotechnology to computer chip miniaturization and vast storage capacity. However, for implementation in the consumer products the present high cost of production must be overcome. There are different ways to make nanosensors e.g. top-down lithography, bottom-up assembly, and self molecular assembly. Consequently, nanomaterials & nanosensors have to be made compatible with the consumer technologies. The progress in detecting and sensing different chemical species with increased accuracy may transform the human society from uncertainty and inaccuracy to more precise and definite world of information. For example, extremely low concentrations of air pollutants or toxic materials in air & water around us can be accurately and economically detected in no time to save the human beings from the serious illnesses. Also, the medical sensors will help in diagnoses of the diseases, their treatment and in predicting the future profile of the individual so that the health insurance companies may exploit the opportunity to grant or to deny the health coverage. Other social issues like privacy invasion and security may be best monitored by the widespread use of the surveillance devices using nanosensors.

  8. La tolerancia como desvirtuación del reconocimiento

    OpenAIRE

    Carlos B. Gutiérrez

    2005-01-01

    El reconocimiento, tal como lo entrevió Hegel, es la dimensión social fundamentadora no sólo de la identidad de los seres humanos sino también de la formación de la conciencia y de la moral. Muchos ven hoy, sin embargo, a la tolerancia como la virtud libe

  9. La familia como campo de saber de las ciencias sociales

    Directory of Open Access Journals (Sweden)

    Yolanda López

    2003-01-01

    Full Text Available Como categoría socio-cultural y como campo de conflictos, la familia constituye un objeto de investigación e intervención de diferentes disciplinas. Si bien cada campo de saber define con respecto a la familia su objeto de estudio, la comprensión de la co

  10. El silencio como estrategia en la obra de Juan Rulfo

    OpenAIRE

    Gómez López-Quiñones, Loreto

    2013-01-01

    Juan Rulfo utiliza el silencio como un espacio para oír y decir mejor en el contexto del México postrevolucionario. Inspirándonos en la terminología de Spivak, pretendemos mostrar el silencio de Rulfo como una estrategia de resistencia ante la representación occidental del Otro.

  11. The ATLAS Silicon Pixel Sensors

    CERN Document Server

    Alam, M S; Einsweiler, K F; Emes, J; Gilchriese, M G D; Joshi, A; Kleinfelder, S A; Marchesini, R; McCormack, F; Milgrome, O; Palaio, N; Pengg, F; Richardson, J; Zizka, G; Ackers, M; Andreazza, A; Comes, G; Fischer, P; Keil, M; Klasen, V; Kühl, T; Meuser, S; Ockenfels, W; Raith, B; Treis, J; Wermes, N; Gössling, C; Hügging, F G; Wüstenfeld, J; Wunstorf, R; Barberis, D; Beccherle, R; Darbo, G; Gagliardi, G; Gemme, C; Morettini, P; Musico, P; Osculati, B; Parodi, F; Rossi, L; Blanquart, L; Breugnon, P; Calvet, D; Clemens, J-C; Delpierre, P A; Hallewell, G D; Laugier, D; Mouthuy, T; Rozanov, A; Valin, I; Aleppo, M; Caccia, M; Ragusa, F; Troncon, C; Lutz, Gerhard; Richter, R H; Rohe, T; Brandl, A; Gorfine, G; Hoeferkamp, M; Seidel, SC; Boyd, GR; Skubic, P L; Sícho, P; Tomasek, L; Vrba, V; Holder, M; Ziolkowski, M; D'Auria, S; del Papa, C; Charles, E; Fasching, D; Becks, K H; Lenzen, G; Linder, C

    2001-01-01

    Prototype sensors for the ATLAS silicon pixel detector have been developed. The design of the sensors is guided by the need to operate them in the severe LHC radiation environment at up to several hundred volts while maintaining a good signal-to-noise ratio, small cell size, and minimal multiple scattering. The ability to be operated under full bias for electrical characterization prior to the attachment of the readout integrated circuit electronics is also desired.

  12. Aircraft Cabin Environmental Quality Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Gundel, Lara; Kirchstetter, Thomas; Spears, Michael; Sullivan, Douglas

    2010-05-06

    The Indoor Environment Department at Lawrence Berkeley National Laboratory (LBNL) teamed with seven universities to participate in a Federal Aviation Administration (FAA) Center of Excellence (COE) for research on environmental quality in aircraft. This report describes research performed at LBNL on selecting and evaluating sensors for monitoring environmental quality in aircraft cabins, as part of Project 7 of the FAA's COE for Airliner Cabin Environmental Research (ACER)1 effort. This part of Project 7 links to the ozone, pesticide, and incident projects for data collection and monitoring and is a component of a broader research effort on sensors by ACER. Results from UCB and LBNL's concurrent research on ozone (ACER Project 1) are found in Weschler et al., 2007; Bhangar et al. 2008; Coleman et al., 2008 and Strom-Tejsen et al., 2008. LBNL's research on pesticides (ACER Project 2) in airliner cabins is described in Maddalena and McKone (2008). This report focused on the sensors needed for normal contaminants and conditions in aircraft. The results are intended to complement and coordinate with results from other ACER members who concentrated primarily on (a) sensors for chemical and biological pollutants that might be released intentionally in aircraft; (b) integration of sensor systems; and (c) optimal location of sensors within aircraft. The parameters and sensors were selected primarily to satisfy routine monitoring needs for contaminants and conditions that commonly occur in aircraft. However, such sensor systems can also be incorporated into research programs on environmental quality in aircraft cabins.

  13. PREFACE: Sensors & their Applications XIII

    Science.gov (United States)

    2005-01-01

    The thirteenth conference in the Sensors and their Applications series took place at the University of Greenwich at Medway, Chatham Maritime, Kent in the UK from 6-8 September 2005. The event was organised by the Instrument Science and Technology Group of the Institute of Physics. Previous conferences in the series were held in Manchester (1983 & 1993), Southampton (1985 & 1998), Cambridge (1987), Canterbury (1989), Edinburgh (1991), Dublin (1995), Glasgow (1997), Cardiff (1999), London (2001) and Limerick (2003). The event provided a forum for academic researchers and industrial engineers working in all areas of sensors, instrumentation and measurement to come together to review and update themselves on the latest technical developments and applications. The longevity of this conference series is testament to the enthusiasm and commitment from the research community working in sensors and related areas. Through presentation of oral papers, discussions at exhibited posters and informal exchanges of ideas, the conference continues to provide excellent knowledge transfer and networking opportunities. The high quality programme, headlined by notable contributions from invited speakers, included silicon microsystems, gas sensing, optical sensors, magnetic sensors, sensor networks and intelligent sensing, digital imaging and process tomography. As in previous years, this conference was particularly highlighted by a large number of sensor applications papers. We take this opportunity to thank all of those who have contributed to the event. Our thanks also go to our colleagues in the Instrument Science and Technology Group for their support and encouragement, particularly in the refereeing of papers. Special thanks go to Claire Pantlin and her team from the Conferences Department of the Institute of Physics who have expertly managed the planning and organising of this Conference. We hope that these conference proceedings will provide a technical insight into the

  14. Flexible Temperature Sensors on Fibers

    OpenAIRE

    Sibinski, Maciej; Jakubowska, Malgorzata; Sloma, Marcin

    2010-01-01

    The aim of this paper is to present research dedicated to the elaboration of novel, miniaturized flexible temperature sensors for textronic applications. Examined sensors were manufactured on a single yarn, which ensures their high flexibility and good compatibility with textiles. Stable and linear characteristics were obtained by special technological process and applied temperature profiles. As a thermo-sensitive materials the innovative polymer compositions filled with multiwalled carbon n...

  15. Hydrogen Leak Detection Sensor Database

    Science.gov (United States)

    Baker, Barton D.

    2010-01-01

    This slide presentation reviews the characteristics of the Hydrogen Sensor database. The database is the result of NASA's continuing interest in and improvement of its ability to detect and assess gas leaks in space applications. The database specifics and a snapshot of an entry in the database are reviewed. Attempts were made to determine the applicability of each of the 65 sensors for ground and/or vehicle use.

  16. Silicon Sensors for HEP Experiments

    CERN Document Server

    Dierlamm, Alexander Hermann

    2017-01-01

    With increasing luminosity of accelerators for experiments in High Energy Physics the demands on the detectors increase as well. Especially tracking and vertexing detectors made of silicon sensors close to the interaction point need to be equipped with more radiation hard devices. This article introduces the different types of silicon sensors, describes measures to increase radiation hardness and provides an overview of present upgrade choices of HEP experiments.

  17. Nanoplasmonic sensors for biointerfacial science.

    Science.gov (United States)

    Jackman, Joshua A; Rahim Ferhan, Abdul; Cho, Nam-Joon

    2017-06-19

    In recent years, nanoplasmonic sensors have become widely used for the label-free detection of biomolecules across medical, biotechnology, and environmental science applications. To date, many nanoplasmonic sensing strategies have been developed with outstanding measurement capabilities, enabling detection down to the single-molecule level. One of the most promising directions has been surface-based nanoplasmonic sensors, and the potential of such technologies is still emerging. Going beyond detection, surface-based nanoplasmonic sensors open the door to enhanced, quantitative measurement capabilities across the biointerfacial sciences by taking advantage of high surface sensitivity that pairs well with the size of medically important biomacromolecules and biological particulates such as viruses and exosomes. The goal of this review is to introduce the latest advances in nanoplasmonic sensors for the biointerfacial sciences, including ongoing development of nanoparticle and nanohole arrays for exploring different classes of biomacromolecules interacting at solid-liquid interfaces. The measurement principles for nanoplasmonic sensors based on utilizing the localized surface plasmon resonance (LSPR) and extraordinary optical transmission (EOT) phenomena are first introduced. The following sections are then categorized around different themes within the biointerfacial sciences, specifically protein binding and conformational changes, lipid membrane fabrication, membrane-protein interactions, exosome and virus detection and analysis, and probing nucleic acid conformations and binding interactions. Across these themes, we discuss the growing trend to utilize nanoplasmonic sensors for advanced measurement capabilities, including positional sensing, biomacromolecular conformation analysis, and real-time kinetic monitoring of complex biological interactions. Altogether, these advances highlight the rich potential of nanoplasmonic sensors and the future growth prospects of

  18. Dual Cryogenic Capacitive Density Sensor

    Science.gov (United States)

    Youngquist, Robert; Mata, Carlos; Vokrot, Peter; Cox, Robert

    2009-01-01

    A dual cryogenic capacitive density sensor has been developed. The device contains capacitive sensors that monitor two-phase cryogenic flow density to within 1% accuracy, which, if temperature were known, could be used to determine the ratio of liquid to gas in the line. Two of these density sensors, located a known distance apart, comprise the sensor, providing some information on the velocity of the flow. This sensor was constructed as a proposed mass flowmeter with high data acquisition rates. Without moving parts, this device is capable of detecting the density change within a two-phase cryogenic flow more than 100 times a second. Detection is enabled by a series of two sets of five parallel plates with stainless steel, cryogenically rated tubing. The parallel plates form the two capacitive sensors, which are measured by electrically isolated digital electronics. These capacitors monitor the dielectric of the flow essentially the density of the flow and can be used to determine (along with temperature) the ratio of cryogenic liquid to gas. Combining this information with the velocity of the flow can, with care, be used to approximate the total two-phase mass flow. The sensor can be operated at moderately high pressures and can be lowered into a cryogenic bath. The electronics have been substantially improved over the older sensors, incorporating a better microprocessor, elaborate ground loop protection and noise limiting circuitry, and reduced temperature sensitivity. At the time of this writing, this design has been bench tested at room temperature, but actual cryogenic tests are pending

  19. Measurement, instrumentation, and sensors handbook

    CERN Document Server

    Eren, Halit

    2014-01-01

    The Second Edition of the bestselling Measurement, Instrumentation, and Sensors Handbook brings together all aspects of the design and implementation of measurement, instrumentation, and sensors. Reflecting the current state of the art, it describes the use of instruments and techniques for performing practical measurements in engineering, physics, chemistry, and the life sciences and discusses processing systems, automatic data acquisition, reduction and analysis, operation characteristics, accuracy, errors, calibrations, and the incorporation of standards for control purposes. Organized acco

  20. Security in wireless sensor networks

    CERN Document Server

    Oreku, George S

    2016-01-01

    This monograph covers different aspects of sensor network security including new emerging technologies. The authors present a mathematical approach to the topic and give numerous practical examples as well as case studies to illustrate the theory. The target audience primarily comprises experts and practitioners in the field of sensor network security, but the book may also be beneficial for researchers in academia as well as for graduate students.