WorldWideScience

Sample records for elements bohrschaechte als

  1. Elemental separation in nanocrystalline Cu-Al alloys

    Science.gov (United States)

    Wang, Y. B.; Liao, X. Z.; Zhao, Y. H.; Cooley, J. C.; Horita, Z.; Zhu, Y. T.

    2013-06-01

    Nanocrystallization by high-energy severe plastic deformation has been reported to increase the solubility of alloy systems and even to mix immiscible elements to form non-equilibrium solid solutions. In this letter, we report an opposite phenomenon—nanocrystallization of a Cu-Al single-phase solid solution by high-pressure torsion separated Al from the Cu matrix when the grain sizes are refined to tens of nanometers. The Al phase was found to form at the grain boundaries of nanocrystalline Cu. The level of the separation increases with decreasing grain size, which suggests that the elemental separation was caused by the grain size effect.

  2. Ductility of Ni3Al doped with substitutional elements

    International Nuclear Information System (INIS)

    Hanada, S.; Chiba, A.; Guo, H.Z.; Watanabe, S.

    1993-01-01

    This paper reports on ductility of B-free Ni 3 Al alloys. Recrystallized Ni 3 Al binary alloys with Ni-rich compositions show appreciable ductility when an environmental effect is eliminated, while the alloys with stoichiometric and Al-rich compositions remain brittle. The ductility in the Ni-rich Ni 3 Al alloys is associated with low ordering energy. The additions of ternary elements, which are classified as γ formers, ductilize ternary Ni 3 Al alloys(Ni-23 at% Al-2 at% X, X = Pd, Pt, Cu and Co), whereas the additions of γ' formers embrittle ternary Ni 3 Al alloys(Ni-23 at% Al-2 at% X, X = Ta, Mo, Nb, Zr, Hf, V, Ti and Si). The additions of small amounts (less than 1 at%) of γ' formers such as Zr and Hf also ductilize as-cast ternary Ni 3 Al alloys. Ductility of Ni 3 Al alloys doped with substitutional elements is discussed in terms of ordering energy and microstructure

  3. Empirical Coulomb matrix elements and the mass of 22Al

    International Nuclear Information System (INIS)

    Whitehead, R.R.; Watt, A.; Kelvin, D.; Rutherford, H.J.

    1976-01-01

    An attempt has been made to obtain a set of Coulomb matrix elements which fit the known Coulomb energy shifts in the nuclei of mass 18 to 22. The interaction obtained fits the data well with only a few exceptions, one of these being the Coulomb shift of the notorious third 0 + state in 18 Ne. These Coulomb matrix elements are used together with the Chung-Wildenthal interaction to obtain a new prediction for the mass excess of 22 Al. The results indicate that 22 Al should be bound against proton emission. (Auth.)

  4. New trace element determinations in the fingernails of ALS patients

    Energy Technology Data Exchange (ETDEWEB)

    Van Dalsem, D.J.; Robinson, L. [Oak Ridge National Lab., TN (United States); Ehmann, W.D. [Kentucky Univ., Lexington, KY (United States). Dept. of Chemistry

    1996-02-01

    ORNL`s High Flux Isotope Reactor was used in a neutron activation analysis experiment to determine selected elemental composition of fingernails from patients afflicted with amyotrophic lateral sclerosis (AL). While no statistical difference were found in aluminium a suggestive difference was observed for copper concentrations.

  5. New trace element determinations in the fingernails of ALS patients

    International Nuclear Information System (INIS)

    Van Dalsem, D.J.; Robinson, L.; Ehmann, W.D.

    1996-01-01

    ORNL's High Flux Isotope Reactor was used in a neutron activation analysis experiment to determine selected elemental composition of fingernails from patients afflicted with amyotrophic lateral sclerosis (AL). While no statistical difference were found in aluminium a suggestive difference was observed for copper concentrations

  6. New trace element determinations in the fingernails of ALS patients

    Energy Technology Data Exchange (ETDEWEB)

    Van Dalsem, D.J.; Ehmann, W.D. [Univ. of Kentucky, Lexington, KY (United States); Robinson, L. [Oak Ridge National Laboratory, TN (United States)

    1996-12-31

    Amyotrophic lateral sclerosis (ALS) afflicts 2 of every 100,000 people in the United States each year. A well-known example of ALS today is Stephen Hawking. He is a theoretical physicist, the author of A Brief History of Time, and is virtually immobilized by ALS. Diseases that cause progressive paralysis because of motor neuron degeneration in the central nervous system are termed motor neuron disorders (MND). Amyotrophic lateral sclerosis is a common form of MND. Pain-free, progressive muscular weakness is the most common clinical symptom. There is chronic weakness with atrophy of the affected muscles by the time the disease is diagnosed. Atrophy eventually results in wheelchair confinement and then only bed without the ability to speak or swallow. Death often occurs as a result of respiratory problems. Unlike other neurodegenerative diseases, in ALS the patient`s bladder and bowel control, eye movement, and mental faculties are preserved. The question today is whether or not certain trace elements are involved in the etiology or pathogenesis of ALS. A collaborative study was undertaken by the University of Kentucky and Oak Ridge National Laboratory (ORNL) using neutron activation analysis (NAA) to study trace element concentrations in ALS patients fingernails to determine if there existed statistically significant imbalances.

  7. Elemental analysis of the Al-Fe intermetallic prepared by fast solidification; Analisis elemental del intermetalico Al-Fe preparado por solidificacion rapida

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval J, R.A.; Lopez M, J.; Ramirez T, J.J.; Aspiazu F, J.; Villasenor S, P. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2003-07-01

    Applying the PIXE technique samples of the Al-Fe intermetallic prepared by fast solidification, obtained starting from Al recycled were analyzed. The concentrations of the found elements are given. (Author)

  8. Elemental analysis of the Al-Fe intermetallic prepared by fast solidification

    International Nuclear Information System (INIS)

    Sandoval J, R.A.; Lopez M, J.; Ramirez T, J.J.; Aspiazu F, J.; Villasenor S, P.

    2003-01-01

    Applying the PIXE technique samples of the Al-Fe intermetallic prepared by fast solidification, obtained starting from Al recycled were analyzed. The concentrations of the found elements are given. (Author)

  9. Properties of U3Si2-Al dispersion fuel element and its application

    International Nuclear Information System (INIS)

    Yin Changgeng

    2001-01-01

    The properties of U 3 Si 2 fuel and U 3 Si 2 -Al dispersion fuel element are introduced, which include U-loading; the banding quality, U-homogeneity and 'dog-bone' phenomenon, the minimum thickness of cladding and the corrosion performances. The fabrication technique of fuel elements, NDT for fuel plates, assemble technique of fuel elements and the application of U 3 Si 2 -Al dispersion fuel elements in the world are introduced

  10. Evolution of Mg-5Al-0.4Mn microstructure after rare earth elements addition

    Directory of Open Access Journals (Sweden)

    A. Żydek

    2011-04-01

    Full Text Available Mg-5Al-0.4Mn-xRE (x = 0, 1, 2, 3 wt.% magnesium alloys were prepared successfully by casting method. The microstructure wasinvestigated by light microscopy. The influence of rare earth (RE elements on the area fraction of eutectic was analysed. The obtainedresults revealed that the as-cast Mg-5Al-0.4Mn alloy consist of α - Mg matrix and eutectic α + γ (where γ is Mg17Al12. However, whilerare earth elements were added to the Mg-Al type alloy, Al11RE3 precipitates were formed. The amount of the Al11RE3 precipitatesincreased with increasing addition of RE, but the amount of γ - Mg17Al12 decreased.

  11. Strength and ductility of Ni3Al alloyed with boron and substitutional elements

    International Nuclear Information System (INIS)

    Ishikawa, K.; Aoki, K.; Masumoto, T.

    1995-01-01

    The effect of simultaneous alloying of boron (B) and the substitutional elements M on mechanical properties of Ni 3 Al was investigated by the tensile test at room temperature. The yield strength of Ni 3 Al+B increases by alloying with M except for Fe and Ga. In particular, it increases by alloying with Hf, Nb, W, Ta, Pd and Si. The fracture strength of Ni 3 Al+B increases by alloying with Pd, Ga, Si and Hf, but decreases with the other elements. Elongation of Ni 3 Al+B increases by alloying with Ga, Fe and Pd, but decreases with other elements. Hf and Pd is the effective element for the increase of the yield strength and the fracture strength of Ni 3 Al+B, respectively. Alloying with Hf leads to the increases of the yield strength and the fracture strength of Ni 3 Al+B, but to the lowering of elongation. On the other hand, alloying with Pd improves all mechanical properties, i.e. the yield strength, the fracture strength and elongation. On the contrary, alloying with Ti, V and Co leads to the lowering of mechanical properties of Ni 3 Al+B. The reason why ductility of Ni 3 Al+B is reduced by alloying with some elements M is discussed

  12. Rare earth elements as a by-catch of sedimentary deposits. Exploration program of rare earth elements; Selten Erd Elemente als Beifang sedimentaerer Lagerstaetten. Erkundungsprogramm Selten Erd Elemente

    Energy Technology Data Exchange (ETDEWEB)

    Linhardt, E.; Gebhardt, A. (comps.)

    2014-02-15

    The increasing demand for rare earth elements (REE) in the field of ''green technologies'' on the one hand and the shortage of raw materials on the world markets on the other hand confronted also Bavaria as an industrial location with growing supply problems in these ''high tech raw materials''. The aim of exploration was the clarification of the feedstock REE potential of heavy mineral concentrates which are obtained in the industrial extraction and processing of sand and kaolin in existing extraction operations in northern Bavaria as by catch and are potentially winnable or marketable. The in-depth investigation enabled the potential of found rare earth elements and other high-tech metal oxides that can be classified as very likely find it in terms of an economic recovery. [German] Der zunehmende Bedarf an Selten Erd Elementen (SEE) im Bereich der ''Gruenen Technologien'' zum Einen sowie die Rohstoffverknappung auf den Weltmaerkten zum Anderen konfrontiert auch Bayern als Industriestandort mit wachsenden Versorgungsproblemen bei diesen ''high tech-Grundstoffen''. Ziel der Erkundung war die Klaerung des rohstofflichen SEE-Potenzials von Schwermineralkonzentraten, die bei der grosstechnischen Gewinnung und Aufbereitung von Sand und Kaolin in vorhandenen Gewinnungsbetrieben Nordbayerns als Beifang anfallen und potenziell gewinn- bzw. vermarktbar sind. Im Zuge der Untersuchung konnten nutzbare Potenziale von Selten Erd Elementen und anderen high-tech - Metalloxiden gefunden werden, die sehr wahrscheinlich als fuendig im Hinblick auf eine wirtschaftliche Gewinnung eingestuft werden koennen.

  13. Electronic Structure and Chemical Bond of Ti3SiC2 and Adding Al Element

    Institute of Scientific and Technical Information of China (English)

    MIN Xinmin; LU Ning; MEI Bingchu

    2006-01-01

    The relation among electronic structure, chemical bond and property of Ti3SiC2 and Al-doped was studied by density function and discrete variation (DFT-DVM) method. When Al element is added into Ti3SiC2, there is a less difference of ionic bond, which does not play a leading role to influent the properties. After adding Al, the covalent bond of Al and the near Ti becomes somewhat weaker, but the covalent bond of Al and the Si in the same layer is obviously stronger than that of Si and Si before adding. Therefore, in preparation of Ti3SiC2, adding a proper quantity of Al can promote the formation of Ti3SiC2. The density of state shows that there is a mixed conductor character in both of Ti3SiC2 and adding Al element. Ti3SiC2 is with more tendencies to form a semiconductor. The total density of state near Fermi lever after adding Al is larger than that before adding, so the electric conductivity may increase after adding Al.

  14. Effect of alloying elements on martensitic transformation in the binary NiAl(β) phase alloys

    International Nuclear Information System (INIS)

    Kainuma, R.; Ohtani, H.; Ishida, K.

    1996-01-01

    The characteristics of the B2(β) to L1 0 (β') martensitic transformation in NiAl base alloys containing a small amount of third elements have been investigated by differential scanning calorimetry (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM). It is found that in addition to the normal L1 0 (3R) martensite, the 7R martensite is also present in the ternary alloys containing Ti, Mo, Ag, Ta, or Zr. While the addition of third elements X (X: Ti, V, Cr, Mn, Fe, Zr, Nb, Mo, Ta, W, and Si) to the binary Ni 64 Al 36 alloy stabilizes the parent β phase, thereby lowering the M s temperature, addition of third elements such as Co, Cu, or Ag destabilizes the β phase, increasing the M s temperature. The occurrence of the 7R martensite structure is attributed to solid solution hardening arising from the difference in atomic size between Ni and Al and the third elements added. The variation in M s temperature with third element additions is primarily ascribed to the difference in lattice stabilities of the bcc and fcc phases of the alloying elements

  15. Preferential site occupancy of alloying elements in TiAl-based phases

    Energy Technology Data Exchange (ETDEWEB)

    Holec, David, E-mail: david.holec@unileoben.ac.at; Reddy, Rajeev K.; Klein, Thomas; Clemens, Helmut [Department of Physical Metallurgy and Materials Testing, Montanuniversität Leoben, Franz-Josef-Strasse 18, A-8700 Leoben (Austria)

    2016-05-28

    First principles calculations are used to study the preferential occupation of ternary alloying additions into the binary Ti-Al phases, namely, γ-TiAl, α{sub 2}-Ti{sub 3}Al, β{sub o}-TiAl, and B19-TiAl. While the early transition metals (TMs, group IVB, VB, and VIB elements) prefer to substitute for Ti atoms in the γ-, α{sub 2}-, and B19-phases, they preferentially occupy Al sites in the β{sub o}-TiAl. Si is, in this context, an anomaly, as it prefers to sit on the Al sublattice for all four phases. B and C are shown to prefer octahedral Ti-rich interstitial positions instead of substitutional incorporation. The site preference energy is linked with the alloying-induced changes of energy of formation, hence alloying-related (de)stabilisation of the phases. We further show that the phase-stabilisation effect of early TMs on β{sub o}-phase has a different origin depending on their valency. Finally, an extensive comparison of our predictions with available theoretical and experimental data (which is, however, limited mostly to the γ-phase) shows a consistent picture.

  16. Finite element simulation of texture evolution and Swift effect in NiAl under torsion

    Science.gov (United States)

    Böhlke, Thomas; Glüge, Rainer; Klöden, Burghardt; Skrotzki, Werner; Bertram, Albrecht

    2007-09-01

    The texture evolution and the Swift effect in NiAl under torsion at 727 °C are studied by finite element simulations for two different initial textures. The material behaviour is modelled by an elastic-viscoplastic Taylor model. In order to overcome the well-known shortcomings of Taylor's approach, the texture evolution is also investigated by a representative volume element (RVE) with periodic boundary conditions and a compatible microstructure at the opposite faces of the RVE. Such a representative volume element takes into account the grain morphology and the grain interaction. The numerical results are compared with experimental data. It is shown that the modelling of a finite element based RVE leads to a better prediction of the final textures. However, the texture evolution path is not accounted for correctly. The simulated Swift effect depends much more on the initial orientation distribution than observed in experiment. Deviations between simulation and experiment may be due to continuous dynamic recrystallization.

  17. Investigation of Product Performance of Al-Metal Matrix Composites Brake Disc using Finite Element Analysis

    International Nuclear Information System (INIS)

    Fatchurrohman, N; Marini, C D; Suraya, S; Iqbal, AKM Asif

    2016-01-01

    The increasing demand of fuel efficiency and light weight components in automobile sectors have led to the development of advanced material parts with improved performance. A specific class of MMCs which has gained a lot of attention due to its potential is aluminium metal matrix composites (Al-MMCs). Product performance investigation of Al- MMCs is presented in this article, where an Al-MMCs brake disc is analyzed using finite element analysis. The objective is to identify the potentiality of replacing the conventional iron brake disc with Al-MMCs brake disc. The simulation results suggested that the MMCs brake disc provided better thermal and mechanical performance as compared to the conventional cast iron brake disc. Although, the Al-MMCs brake disc dissipated higher maximum temperature compared to cast iron brake disc's maximum temperature. The Al-MMCs brake disc showed a well distributed temperature than the cast iron brake disc. The high temperature developed at the ring of the disc and heat was dissipated in circumferential direction. Moreover, better thermal dissipation and conduction at brake disc rotor surface played a major influence on the stress. As a comparison, the maximum stress and strain of Al-MMCs brake disc was lower than that induced on the cast iron brake disc. (paper)

  18. Effect of alloying elements on the shape memory properties of ductile Cu-Al-Mn alloys

    International Nuclear Information System (INIS)

    Sutou, Y.; Kainuma, R.; Ishida, K.

    1999-01-01

    The effect of alloying elements on the M s temperature, ductility and the shape memory properties of Cu-Al-Mn ductile shape memory (SM) alloys was investigated by differential scanning calorimetry, cold-rolling and tensile test techniques. It was found that the addition of Au, Si and Zn to the Cu 73 -Al 17 -Mn 10 alloy stabilized the martensite (6M) phase increasing the M s temperature, while the addition of Ag, Co, Cr, Fe, Ni, Sn and Ti decreased the stability of the martensite phase, decreasing the M s temperature. The SM properties were improved by the addition of Co, Ni, Cr and Ti. (orig.)

  19. Analysis of heavy alloying elements segregation in gravity cast experimental Mg-Al-Zn-RE alloy

    Directory of Open Access Journals (Sweden)

    A. Żydek

    2010-01-01

    Full Text Available Microstructure of experimental AZ91 alloy with an addition of rare earth elements (RE at a level of 4 wt.% was examined by means of light microscopy. The investigated AZ91 + 4 wt.% RE alloy was fabricated by adding cerium rich mish metal to molten commercial AZ91 alloy. In the microstructure of the resulting alloy, besides α solid solution, α + γ eutectic and discontinuous precipitates of γ phase, also the Al11RE3 phase with needle-like morphology and the polygonal Al10RE2Mn7 phase were revealed. No segregation of rare earth elements was found in the investigated gravity cast alloy, which was confirmed by statistical analysis of cerium concentrations in selected parts of the cast. Similar results were obtained for manganese. Ce and Mn concentrations were determined by a spectrophotometric method.

  20. Repetitive element transcripts are elevated in the brain of C9orf72 ALS/FTLD patients.

    Science.gov (United States)

    Prudencio, Mercedes; Gonzales, Patrick K; Cook, Casey N; Gendron, Tania F; Daughrity, Lillian M; Song, Yuping; Ebbert, Mark T W; van Blitterswijk, Marka; Zhang, Yong-Jie; Jansen-West, Karen; Baker, Matthew C; DeTure, Michael; Rademakers, Rosa; Boylan, Kevin B; Dickson, Dennis W; Petrucelli, Leonard; Link, Christopher D

    2017-09-01

    Significant transcriptome alterations are detected in the brain of patients with amyotrophic lateral sclerosis (ALS), including carriers of the C9orf72 repeat expansion and C9orf72-negative sporadic cases. Recently, the expression of repetitive element transcripts has been associated with toxicity and, while increased repetitive element expression has been observed in several neurodegenerative diseases, little is known about their contribution to ALS. To assess whether aberrant expression of repetitive element sequences are observed in ALS, we analysed RNA sequencing data from C9orf72-positive and sporadic ALS cases, as well as healthy controls. Transcripts from multiple classes and subclasses of repetitive elements (LINEs, endogenous retroviruses, DNA transposons, simple repeats, etc.) were significantly increased in the frontal cortex of C9orf72 ALS patients. A large collection of patient samples, representing both C9orf72 positive and negative ALS, ALS/FTLD, and FTLD cases, was used to validate the levels of several repetitive element transcripts. These analyses confirmed that repetitive element expression was significantly increased in C9orf72-positive compared to C9orf72-negative or control cases. While previous studies suggest an important link between TDP-43 and repetitive element biology, our data indicate that TDP-43 pathology alone is insufficient to account for the observed changes in repetitive elements in ALS/FTLD. Instead, we found that repetitive element expression positively correlated with RNA polymerase II activity in postmortem brain, and pharmacologic modulation of RNA polymerase II activity altered repetitive element expression in vitro. We conclude that increased RNA polymerase II activity in ALS/FTLD may lead to increased repetitive element transcript expression, a novel pathological feature of ALS/FTLD. © The Author 2017. Published by Oxford University Press.

  1. Production of Al-Ti-C grain refiners with the addition of elemental carbon

    International Nuclear Information System (INIS)

    Gezer, Berke Turgay; Toptan, Fatih; Daglilar, Sibel; Kerti, Isil

    2010-01-01

    Grain refining process used in aluminium alloys, has an important role for preventing columnar, coarse grains and encouraging fine, equiaxed grain formation. Al-Ti-B grain refiners are widely used as aluminium grain refiners despite the problems in application Al-Ti-C refiners have an increasing demand in recent years. In the present work, Al-Ti-C grain refiners with different Ti:C ratios were produced by insitu method with the addition of elemental carbon. Microstructures were characterised by optic microscope and scanning electron microscope equipped with energy dispersive spectroscopy. The effects of temperature, holding time and Ti:C ratio on the grain refinement process were investigated and optimum conditions were determined.

  2. Ordering and site occupancy of ternary elements in Fe{sub 3}Al

    Energy Technology Data Exchange (ETDEWEB)

    Rademacher, Thomas; Al-Kassab, Talaat; Kirchheim, Reiner [Institut fuer Materialphysik, Universitaet Goettingen (Germany)

    2009-07-01

    Ordered iron aluminides exhibit a number of advantageous properties, such as high-temperature strength, corrosion resistance and low cost. Therefore, iron aluminum based alloys are considered to replace in some cases high alloyed ferritic stainless steels, especially DO{sub 3} - ordered Fe{sub 3}Al. The mechanical properties and high-temperature stability can be optimized when ternary elements are added. In this study the site occupancy of ternary elements (4at.%V, 5at.%Cr, 5at.%Mn) has been investigated by means of Atom Probe Tomography (APT). A special analysis algorithm allows resolving the atom layers for different measurement directions which enables determining site preferences. Additionally, comparing the succession of layers with simulations the binding energies of the participating elements can be estimated.

  3. Influences of alloying elements and oxygen on the stability and elastic properties of Mg17Al12

    International Nuclear Information System (INIS)

    Dai, Jianhong; Song, Yan; Yang, Rui

    2014-01-01

    Highlights: • Most alloying elements stabilize Mg 17 Al 12 with negative occupation energy. • The alloying element and oxygen co-existed Mg 17 Al 12 are stable. • Strong bonding interactions existed between alloying element and host atoms. - Abstract: Influence of alloying elements (Ca, Mn, Ni, Cu, Zn, Zr, Sn, and La) and oxygen on stability and elastic properties of Mg 17 Al 12 has been studied by first principles total energy calculations. The occupation preferences of oxygen and alloying elements in Mg 17 Al 12 are identified. Ca, Zr, and La tend to substitute for Mg atoms, Zn, Cu, and Ni prefer to occupy Al site, and Mn and Sn show positive occupation energy for substituting both Mg and Al atoms. The impurity oxygen prefers to occupy interstitial sites surrounded by four Mg atoms regardless the presence of alloying elements in this system. Elastic constants were estimated to evaluate the mechanical stability of alloyed systems. The results show that alloys which own negative occupation energy also satisfy the mechanical stability criteria. Electronic structures were analyzed to clarify the intrinsic mechanisms of how alloying elements and oxygen influence the stability of Mg 17 Al 12 . The stabilization effect of alloying elements and oxygen was found to originate from the strong bonding interaction with the matrix

  4. Microstructural evolution during hot pressing of the blended elemental Ti-6%Al-7%Nb alloy

    International Nuclear Information System (INIS)

    Henriques, V.A.R.; Sandim, H.R.Z.; Coelho, G.C.; Silva, C.R.M. da

    2003-01-01

    The Ti-6%Al-7%Nb (wt.%) α-β alloy was developed aiming the replacement of the traditional Ti-6%Al-4%V alloy in surgical implants owing to its larger biocompatibility. Samples of this alloy were obtained using the blended elemental (BE) technique. The isochronal hot pressing of the compacts was carried out in the range 700-1500 deg. C with a compaction pressure of 20 MPa and a heating rate of 20 deg. C min -1 . In this work, the behavior of the elementary powders during the hot pressing and the corresponding microstructural evolution were investigated. The alloy was characterized by means of scanning electron microscopy (SEM) in the backscattered mode (BSE), X-ray diffraction (XRD), and density measurements. The results indicate that the homogenization of the alloy is diffusion-controlled and Ti.Al intermediary compounds (TiAl and Ti 3 Al) are formed at lower temperatures. With increasing temperature, homogenization of the alloy takes place and a coarse plate-like α+intergranular β structure is found throughout the microstructure in temperatures above 1300 deg. C. The process variables were defined aiming to minimize interstitial pick-up (C, O, and N) and avoiding intensive grain growth

  5. Essential trace elements in amyotrophic lateral sclerosis (ALS): Results in a population of a risk area of Italy.

    Science.gov (United States)

    Forte, Giovanni; Bocca, Beatrice; Oggiano, Riccardo; Clemente, Simonetta; Asara, Yolande; Sotgiu, Maria Alessandra; Farace, Cristiano; Montella, Andrea; Fois, Alessandro Giuseppe; Malaguarnera, Michele; Pirina, Pietro; Madeddu, Roberto

    2017-09-01

    Sardinian (Italy) island population has a uniquely high incidence of amyotrophic lateral sclerosis (ALS). Essential trace element levels in blood, hair, and urine of ALS Sardinian patients were investigated in search of valid biomarkers to recognize and predict ALS. Six elements (Ca, Cu, Fe, Mg, Se, and Zn) were measured in 34 patients compared to 30 age- and sex-matched healthy controls by a validated method. Levels of Ca and Cu in blood and of Se and Zn in hair were significantly higher in ALS than in controls, while urinary excretion of Mg and Se was significantly decreased. The selected cut-off concentrations for these biomarkers may distinguish patients with or without ALS with sufficient sensitivity and specificity. Many positive (as Se-Cu and Se-Zn) and negative associations (as Ca-Mg and Ca-Zn) between elements suggested that multiple metals involved in multiple mechanisms have a role in the ALS degeneration.

  6. High-Uranium-Loaded U3O8-Al fuel element development program. Part 1

    International Nuclear Information System (INIS)

    Martin, M.M.

    1993-01-01

    The High-Uranium-Loaded U 3 O 8 -Al Fuel Element Development Program supports Argonne National Laboratory efforts to develop high-uranium-density research and test reactor fuel to accommodate use of low-uranium enrichment. The goal is to fuel most research and test reactors with uranium of less than 20% enrichment for the purpose of lowering the potential for diversion of highly-enriched material for nonpeaceful usages. The specific objective of the program is to develop the technological and engineering data base for U 3 O 8 -Al plate-type fuel elements of maximal uranium content to the point of vendor qualification for full scale fabrication on a production basis. A program and management plan that details the organization, supporting objectives, schedule, and budget is in place and preparation for fuel and irradiation studies is under way. The current programming envisions a program of about four years duration for an estimated cost of about two million dollars. During the decades of the fifties and sixties, developments at Oak Ridge National Laboratory led to the use of U 3 O 8 -Al plate-type fuel elements in the High Flux Isotope Reactor, Oak Ridge Research Reactor, Puerto Rico Nuclear Center Reactor, and the High Flux Beam Reactor. Most of the developmental information however applies only up to a uranium concentration of about 55 wt % (about 35 vol % U 3 O 8 ). The technical issues that must be addressed to further increase the uranium loading beyond 55 wt % U involve plate fabrication phenomena of voids and dogboning, fuel behavior under long irradiation, and potential for the thermite reaction between U 3 O 8 and aluminum

  7. Trace elements in ALS patients and their relationships with clinical severity.

    Science.gov (United States)

    Oggiano, Riccardo; Solinas, Giuliana; Forte, Giovanni; Bocca, Beatrice; Farace, Cristiano; Pisano, Andrea; Sotgiu, Maria Alessandra; Clemente, Simonetta; Malaguarnera, Michele; Fois, Alessandro Giuseppe; Pirina, Pietro; Montella, Andrea; Madeddu, Roberto

    2018-04-01

    An exploratory study of trace elements in ALS and their relationships with clinical severity was detected. Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disorder that causes irreversible damage in humans, with the consequent loss of function of motoneurons (MNs), with a prognosis up to 5 years after diagnosis. Except to genetic rare cases it is not known the etiology of the disorder. Aim of our research is to investigate the possible role of heavy metals in the severity of the disease. In this study, by the use of plasma mass (ICP-MS), we have analyzed the content of essential and heavy metals such: Pb, Cd, Al, Hg, Mn, Fe, Cu, Zn, Se, Mg, and Ca, in blood, urine and hair of ALS patients and controls; moreover we divided the patients in two groups for disease severity and analyzed the difference among the groups, in order to study a possible involvement of metals in the severity of the damage. Our results suggest a protective role of Selenium, involved in protective antioxidant mechanisms, and a risk factor in the case of presence of Lead in blood. The levels of the other metals are not easy to interpret, because these may be due to life style and for essential metals a consequence of the disease condition, not a cause. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. Effects of Al addition and minor elements on oxidation behaviour of FeCr alloys

    International Nuclear Information System (INIS)

    Herbelin, J.M.; Mantel, M.

    1995-01-01

    It is shown that the addition of aluminium is very effective for the high temperature oxidation resistance of FeCr alloys. 1% aluminium produces a continuous protective Al 2 O 3 oxide for FeCr alloy that contains more than 13% of chromium. However this aluminium content is not enough for the high temperature resistance of thin foils and a 5% aluminium content is needed since the substrate plays the role of an aluminium reserve susceptible to oxidation. Impurity elements such as sulphur are detrimental and give rise to scaling of the oxide layer. Active elements such as Y, Ce, La, Zr are therefore necessary to tie up sulphur and increase the life of the alloys. (orig.)

  9. High performance Ti-6Al-4V + TiC alloy by blended elemental powder metallurgy

    International Nuclear Information System (INIS)

    Fujii, H.; Yamazaki, T.; Horiya, T.; Takahashi, K.

    1993-01-01

    The blended elemental powder metallurgy (BE) of titanium alloys is one of the most cost saving technologies, in which the blending of titanium powder and alloying element powders (or master alloy powders), precise compaction at room temperature, and consolidation are conducted in turn. In addition to some economical and material saving advantages, the BE has a noteworthy feature, that is, the synthesis of special alloy systems which are difficult to be produced by the ingot metallurgy. A particle or fiber reinforced metal matrix composite (MMC) is one of the examples, and the addition of TiC particles to the extensively used Ti-6Al 4V has succeeded in obtaining higher tensile strength, Young's modulus, and elevated temperature properties. However, the raising up of some properties sometimes deteriorates other ones in MMC, and it often prevents the practical use. In this research work, the improvement of tensile ductility and fatigue properties of Ti-6Al-4V+TiC alloys without lowering other mechanical properties is aimed through the microstructural control

  10. Effect of Alloy Elements on Microstructures and Mechanical Properties in Al-Mg-Si Alloys

    Science.gov (United States)

    Kato, Yoshikazu; Hisayuki, Koji; Sakaguchi, Masashi; Higashi, Kenji

    Microstructures and mechanical properties in the modified Al-Mg-Si alloys with variation in the alloy elements and their contents were investigated to enhance higher strength and ductility. Optimizing both the alloy element design and the industrial processes including heat-treatments and extrusion technology was carried out along the recent suggestion from the first principles calculation. The investigation concluded that the addition of Fe and/or Cu could recovery their lost ductility, furthermore increase their tensile strength up to 420 MPa at high elongation of 24 % after T6 condition for Al-0.8mass%Mg-1.0mass%Si-0.8mass%Cu-0.5mass%Fe alloy with excess Si content. The excellent combination between strength and ductility could be obtained by improvement to the grain boundary embitterment caused by grain boundary segregation of Si as a result from the interaction of Si with Cu or Fe with optimizing the amount of Cu and Fe contents.

  11. First Principles Study of Adsorption of Hydrogen on Typical Alloying Elements and Inclusions in Molten 2219 Al Alloy

    Directory of Open Access Journals (Sweden)

    Yu Liu

    2017-07-01

    Full Text Available To better understand the effect of the components of molten 2219 Al alloy on the hydrogen content dissolved in it, the H adsorption on various positions of alloying element clusters of Cu, Mn and Al, as well as the inclusion of Al2O3, MgO and Al4C3, were investigated by means of first principles calculation, and the thermodynamic stability of H adsorbed on each possible site was also studied on the basis of formation energy. Results show that the interaction between Al, MgO, Al4C3 and H atoms is mainly repulsive and energetically unfavorable; a favorable interaction between Cu, Mn, Al2O3 and H atoms was determined, with H being more likely to be adsorbed on the top of the third atomic layer of Cu(111, the second atomic layer of Mn(111, and the O atom in the third atomic layer of Al2O3, compared with other sites. It was found that alloying elements Cu and Mn and including Al2O3 may increase the hydrogen adsorption in the molten 2219 Al alloy with Al2O3 being the most sensitive component in this regard.

  12. Determination of chemical state of Al doping element in ZnO layer

    International Nuclear Information System (INIS)

    Csik, A.; Toth, J.; Lovics, R.; Takats, V.; Hakl, J.; Vad, K.

    2011-01-01

    Complete text of publication follows. Transparent and conducting oxides (TCO) thin films are very important from the scientific and technological point of view. The coexistence of electrical conductivity and optical transparency in these materials makes it possible to use them in modern technologies: transparent electrodes for flat panel displays and photovoltaic cells, low emissivity windows, transparent thin films transistors, light emitting diodes. One of the important TCO semiconductors is the impurity-doped zinc-oxide (ZnO) layer, for example aluminium doped zinc-oxide layer (AZO), due to its unique physical and chemical properties. It has wide band gap (3.44 eV) and large exciton binding energy (60 meV). ZnO thin layers have a great interest for potential applications in optical and optoelectronic devices. Furthermore, high quality single crystal ZnO wafers has already been available as a result of new developments in ZnO growth technologies with the capability to scale up wafer size, which is an important factor for increasing efficiency of solar cells. Nonetheless, in order to enable the use of ZnO layers with enhanced electrical properties, higher conductivities can be obtained by doping with donor elements such as aluminium, gallium, indium, boron or fluorine. Investigation of p-type doping possibilities, diffusion processes and thermal stability of these layers are in the focus of interest in the interpretation of their optical and electrical properties, and the prediction of their lifetime. In our SNMS/SIMS-XPS laboratory, experiments on TCO layered structures were carried on. Depth profile and chemical state analyses of ZnO/AlO/ZnO layered structures were performed by Secondary Neutral Mass Spectrometry (SNMS) and X-ray photoelectron spectroscopy (XPS). The samples were produced by atomic layer deposition technique with the following layered structure: between a few hundred atomic layers of ZnO was an AlO atomic layer. The SNMS was used for depth

  13. Examination of U3Si2-Al fuel elements from the Oak Ridge Research Reactor

    International Nuclear Information System (INIS)

    Copeland, G.L.; Snelgrove, J.L.; Hofman, G.L.

    1986-01-01

    The results of postirradiation examination of low-enriched U 3 Si 2 fuel elements from the Oak Ridge Research Reactor are presented. The elements replaced standard high-enriched elements and were handled routinely except that the burnup of half the elements was extended beyond normal limits up to about 98% peak. The elements were manufactured by commercial fuel suppliers. The performance was completely satisfactory for all the elements

  14. The reactive element effect of yttrium and yttrium silicon on high temperature oxidation of NiCrAl coating

    Science.gov (United States)

    Ramandhany, S.; Sugiarti, E.; Desiati, R. D.; Martides, E.; Junianto, E.; Prawara, B.; Sukarto, A.; Tjahjono, A.

    2018-03-01

    The microstructure formed on the bond coat affects the oxidation resistance, particularly the formation of a protective oxide layer. The adhesion of bond coat and TGO increased significantly by addition of reactive element. In the present work, the effect of yttrium and yttrium silicon as reactive element (RE) on NiCrAl coating was investigated. The NiCrAl (without RE) and NiCrAlX (X:Y or YSi) bond coating were deposited on Hastelloy C-276 substrate by High Velocity Oxygen Fuel (HVOF) method. Isothermal oxidation was carried out at 1000 °C for 100 hours. The results showed that the addition of RE could prevent the breakaway oxidation. Therefore, the coating with reactive element were more protective against high temperature oxidation. Furthermore, the oxidation rate of NiCrAlY coating was lower than NiCrAlYSi coating with the total mass change was ±2.394 mg/cm2 after 100 hours of oxidation. The thickness of oxide scale was approximately 1.18 μm consisting of duplex oxide scale of spinel NiCr2O4 in outer scale and protective α-Al2O3 in inner scale.

  15. Postirradiation examination of a low enriched U3Si2-Al fuel element manufactured and irradiated at Batan, Indonesia

    International Nuclear Information System (INIS)

    Suripto, A.; Sugondo, S.; Nasution, H.

    1994-01-01

    The first low-enriched U 3 Si 2 -Al dispersion plate-type fuel element produced at the Nuclear Fuel Element Center, BATAN, Indonesia, was irradiated to a peak 235 U burnup of 62%. Postirradiation examinations performed to data shows the irradiation behavior of this element to be similar to that of U 3 Si 2 -Al plate-type fuel produced and tested at other institutions. The main effect of irradiation on the fuel plates is a thickness increase of 30--40 μm (2.5-3.0%). This thickness increase is almost entirely due to the formation of a corrosion layer (Boehmite). The contribution of fuel swelling to the thickness increase is rather small (less than 10 μm) commensurate with the burnup of the fuel and the relatively moderate as-fabricated fuel volume fraction of 27% in the fuel meat

  16. Synthesis and elastic properties of V2AlC thin films by magnetron sputtering from elemental targets

    International Nuclear Information System (INIS)

    Sigumonrong, Darwin P; Music, Denis; Schneider, Jochen M; Zhang Jie; Zhou Yanchun

    2009-01-01

    The influence of deposition temperature on phase formation of V 2 AlC is studied by magnetron sputtering from elemental targets. At substrate temperatures below 750 0 C, we observed the formation of Al x V y and V 2 C using x-ray diffraction (XRD) analysis. At 750 0 C, a phase pure polycrystalline V 2 AlC film on a ∼12 nm thick transition layer has been observed using XRD and transmission electron microscopy. Selected area electron diffraction indicates that the film grown on the transition layer consists of phase pure V 2 AlC. As the substrate temperature is increased to 850 0 C, the formation of V 2 C in addition to the V 2 AlC phase is observed. This may be due to desorption of aluminium causing the decomposition of V 2 AlC into vanadium carbides and aluminium. The V 2 AlC film is fully dense and polycrystalline and the elastic modulus based on nanoindentation is within the expected error margin consistent with previously reported theoretical calculations and the diamond anvil cell measurement of bulk V 2 AlC samples.

  17. Synthesis and elastic properties of V{sub 2}AlC thin films by magnetron sputtering from elemental targets

    Energy Technology Data Exchange (ETDEWEB)

    Sigumonrong, Darwin P; Music, Denis; Schneider, Jochen M [Materials Chemistry, RWTH Aachen University, Mies-van-der-Rohe-Str. 10, 52074 Aachen (Germany); Zhang Jie; Zhou Yanchun [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

    2009-09-21

    The influence of deposition temperature on phase formation of V{sub 2}AlC is studied by magnetron sputtering from elemental targets. At substrate temperatures below 750 {sup 0}C, we observed the formation of Al{sub x}V{sub y} and V{sub 2}C using x-ray diffraction (XRD) analysis. At 750 {sup 0}C, a phase pure polycrystalline V{sub 2}AlC film on a {approx}12 nm thick transition layer has been observed using XRD and transmission electron microscopy. Selected area electron diffraction indicates that the film grown on the transition layer consists of phase pure V{sub 2}AlC. As the substrate temperature is increased to 850 {sup 0}C, the formation of V{sub 2}C in addition to the V{sub 2}AlC phase is observed. This may be due to desorption of aluminium causing the decomposition of V{sub 2}AlC into vanadium carbides and aluminium. The V{sub 2}AlC film is fully dense and polycrystalline and the elastic modulus based on nanoindentation is within the expected error margin consistent with previously reported theoretical calculations and the diamond anvil cell measurement of bulk V{sub 2}AlC samples.

  18. Finite element analysis of Al 2024/Cu-Al-Ni shape memory alloy composites with defects/cracks

    Science.gov (United States)

    Kotresh, M.; Benal, M. M., Dr; Siddalinga Swamy, N. H., Dr

    2018-02-01

    In this work, a numerical approach to predict the stress field behaviour of defect/crack in shape memory alloy (SMA) particles reinforced composite known as the adaptive composite is presented. Simulation is based on the finite element method. The critical stress field approach was used to determine the stresses around defect/crack. Thereby stress amplification issue is being resolved. In this paper, the effect volume % of shape memory alloy and shape memory effect of reinforcement for as-cast and SME trained composites are examined and discussed. Shape memory effect known as training is achieved by pre-straining of reinforcement particles by equivalent changes in their expansion coefficients.

  19. Effect of RE elements on the microstructural evolution of as cast and SIMA processed Mg-4Al alloy

    International Nuclear Information System (INIS)

    Nayyeri, Mohammad Javad; Khomamizadeh, Farzad

    2011-01-01

    Research highlights: → In this article, we examined the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process. → Our investigations contained metallographic observation, scanning electron microscope and quantitative metallographic methods. → Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the amount of RE elements increased from 0 through 4 percent. → Also we studied the effect of RE elements on the quality and quantityof intragranular liquid droplets as well as kinetic of microstructural changes. → Moreover, the effect of REs on the other parameters such as fraction of liquid, shape factor and particle size was studied.In this article, we examined the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process. Our investigations contained metallographic observation, scanning electron microscope and quantitative metallographic methods. Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the amount of RE elements increased from 0 through 4 percent. Also we studied the effect of RE elements on the quality and quantityof intragranular liquid droplets as well as kinetic of microstructural changes. Moreover, the effect of REs on the other parameters such as fraction of liquid, shape factor and particle size was studied. - Abstract: In the present article, the effect of Rare Earth elements on the microstructural development of as cast and semisolid Mg-4Al alloy produced by SIMA process is studied. Investigation conducted by metallographic observation, scanning electron microscope and quantitative metallographic methods. Results showed that alloy's dendrites turn into larger fully dendritic shape with sharp and narrow arms from equiaxed rosette type as the

  20. Effect of Rare Earth Element on Microstructure and Properties of in situ Synthesized TiB2/Al Composites

    Directory of Open Access Journals (Sweden)

    QU Min

    2018-03-01

    Full Text Available The effect of rare earth element Ce, Sc and Er on TiB2 particles and matrix alloy micros-tructure of TiB2/Al composites was studied with in situ synthesis method. It shows that the addition of rare earth element improves the microstructure and properties of TiB2/Al composites notably. The particles of TiB2 are relatively homogenously distributed as adding 0.3% (mass fraction rare earth element Sc and Er, moreover, it is Er that refines the microstructure of matrix alloy most significantly, then is Sc. Similarly, it is demonstrated that the addition of Sc and Er results in better tensile strength, which is enhanced by 32% and 31%, respectively; the addition of Er also leads to the best ductility by 85% with optimal tensile property. Meanwhile, fracture morphology analysis reveals that the fracture of the composites is microporous gathered ductile fracture when adding Sc and Er. Finally, it is verified that the mechanism of rare earth element on composites lies in two aspects:one is that the addition of rare earth element improves the wettability of the composites and suppresses the agglomeration of TiB2 particles; the other is that the addition of rare earth element refines the microstructure of matrix alloy and then improves the tensile strength of the composites.

  1. Elemental investigation of (Al-Cu) alloys and some geological samples using neutron activation and XRF analysis techniques

    International Nuclear Information System (INIS)

    Hammad, E.A.M.

    2012-01-01

    Neutron activation analysis (NAA) using k 0 - standardization (k 0 -NAA) is well known method for multi-elemental analysis. The method is used to analyze different samples belonging to different fields. In addition, X- ray fluorescence (XRF) is also used for multi-elemental analysis. XRF complements NAA methods. Both methods were used for investigation of some iron ores and aluminum- cupper alloy (Al-Cu) samples. Elemental concentration of Iron ores and Al-Cu alloy samples were determined by k 0 - NAA and XRF methods. The iron ore samples were collected from Wadi Kareim and Umm Nar sites (the Eastern desert of Egypt). Six and two samples representing the ores of Wadi Kareim and Umm Nar, respectively altogether with the standard samples consisting of Fe, Au , Zr and W and the certified reference sample IAEA Soil-7 were irradiated in one of the irradiated boxes at the Second Egyptian Research Reactor (ETRR- 2). The induced activities were counted using an efficiency calibrated HPGe detector systems. The neutron spectrum parameters α and f characterizing the neutron irradiation position that are needed in applying k 0 -NAA method were determined using the activation product of Zr , Au, Fe and W and found α≅ - 0.048 ±0.002 and f ≅ 38± k 0 -NAA method was applied to determine the elemental concentrations in the two iron ore samples. The concentrations determined were found to vary erratically form one sample to another. The results were discussed and compared with similar results in literature. The accuracy of the k 0 - NAA method was checked by determining the elemental concentration in the IAEA-Soil 7 reference sample. The obtained results are compared with the recommended values. Good agreements were found within 10 %. Short time neutron activation analysis (STNAA) was carried out to determine concentration of major elements in Al-Cu alloy samples. Three (Al-Cu) alloys samples with different concentrations of Cu (2, 3.5 and 5 %) altogether. Au standard sample

  2. Stability and migration of vacancy in V–4Cr–4Ti alloy: Effects of Al, Si, Y trace elements

    International Nuclear Information System (INIS)

    Zhang, Chong; Zhang, Pengbo; Li, Ruihuan; Zhao, Jijun; Dong, Chuang

    2013-01-01

    Addition of trace amounts of Al, Si and Y into V–4Cr–4Ti alloy is beneficial for the mechanical properties under irradiation. It is thus important to investigate the influence of solute/trace elements on stabilities, energetics and diffusion behaviors of vacancy defects. We performed first-principles calculations to evaluate vacancy–solute/trace interaction inside dilute V–X (X = Ti, Cr, Al, Si, Y) and V–4Cr–4Ti–(Al, Si, Y) alloys. With addition of Si and Y, vacancy-based complexes tend to form near Ti–Si and Ti–Y pairs, while the effect of Al is negligible. Moreover, diffusion coefficients of solute/trace element in vanadium were derived using nine-frequency model. With high binding energy and low diffusion coefficient, Si atom is strongly attractive to vacancy in vanadium matrix. Our theoretical results suggest that the interactions between vacancy and solute/trace elements play some role in the evolution of microstructures inside vanadium alloys

  3. A study on the formation of iron aluminide (FeAl) from elemental powders

    Energy Technology Data Exchange (ETDEWEB)

    Sina, H.; Corneliusson, J.; Turba, K.; Iyengar, S.

    2015-07-05

    Highlights: • Fe–40 at.% Al discs with coarse iron powder showed precombustion and combustion peaks. • Loose powder mixtures and discs with fine iron powder showed only combustion peaks. • Slower heating rate and fine aluminum particles promote precombustion. • The major product formed during both the reactions was Fe{sub 2}Al{sub 5}. • Heating the samples to 1000 °C yielded a stable FeAl phase as the final product. - Abstract: The formation of iron aluminide (FeAl) during the heating of Fe–40 at.% Al powder mixture has been studied using a differential scanning calorimeter. The effect of particle size of the reactants, compaction of the powder mixtures as well as the heating rate on combustion behavior has been investigated. On heating compacted discs containing relatively coarser iron powder, DSC data show two consecutive exothermic peaks corresponding to precombustion and combustion reactions. The product formed during both these reactions is Fe{sub 2}Al{sub 5} and there is a volume expansion in the sample. The precombustion reaction could be improved by a slower heating rate as well as a better surface coverage of iron particles using relatively finer aluminum powder. The combustion reaction was observed to be weaker after a strong precombustion stage. Heating the samples to 1000 °C resulted in the formation of a single and stable FeAl phase through the diffusional reaction between Fe{sub 2}Al{sub 5} and residual iron. DSC results for compacted discs containing relatively finer iron powder and for the non-compacted samples showed a single combustion exotherm during heating, with Fe{sub 2}Al{sub 5} as the product and traces of FeAl. X-ray diffraction and EDS data confirmed the formation of FeAl as the final product after heating these samples to 1000 °C.

  4. Low Z elements (Mg, Al, and Si) K-edge X-ray absorption spectroscopy in minerals and disordered systems

    International Nuclear Information System (INIS)

    Ildefonse, P.; Calas, G.; Flank, A.M.; Lagarde, P.

    1995-01-01

    Soft X-ray absorption near edge spectroscopy (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopy have been performed at the Mg-, Al- and Si-K edges in order to establish the ability of this spectroscopy to derive structural information in disordered solids such as glasses and gels. Mg- and Al-K XANES are good structural probes to determine the coordination state of these elements in important minerals, glasses and gels. In a CaO-MgO-2SiO 2 glass Mg XANES spectra differ from that found in the crystalline equivalent, with a significant shift of the edge maxima to lower energy, consistent with a CN lower than 6. Mg-EXAFS on the same sample are in agreement and indicate the presence of 5-coordinated Mg with Mg-O distances of 2.01 A. In aluminosilicate gels, Al-K XANES has been used to investigate the [4]Al/Al total ratios. These ratios increase as the Al/Si ratios decrease. Aluminosilicate and ferric-silicate gels were studied by using Si-K edge XANES. XANES spectra differ significantly among the samples studied. Aluminosilicate gels with Al/Si=1 present a different Al and Si local environment from that known in clay minerals with the same Al/Si ratio. The gel-to-mineral transformation thus implies a dissolution-recrystallization mechanism. On the contrary, ferric-silicate gel presents a Si local environment close to that found in nontronite which may be formed by a long range ordering of the initial gels. (orig.)

  5. The technique for determination of surface contamination by uranium on U3Si2-Al plate-type fuel elements

    International Nuclear Information System (INIS)

    Li Shulan; He Fengqi; Wang Qingheng; Han Jingquan

    1993-04-01

    The NDT method for determining the surface contamination by uranium on U 3 Si 2 -Al plate-type fuel elements, the process of standard specimen preparation and the graduation curve are described. The measurement results of U 3 Si 2 -Al plate-type fuel elements show that the alpha counting method to measure the surface contamination by uranium on fuel plate is more reliable. The UB-1 type surface contamination meter, which was recently developed, has many advantages such as high sensitivity to determine the uranium pollution, short time in measuring, convenience for operation, and the minimum detectable amount of uranium is 5 x 10 -10 g/cm 2 . The measuring device is controlled by a microcomputer. Besides data acquisition and processing, it has functions of statistics, output data on terminal or to printer and alarm. The procedures of measurement are fully automatic. All of these will meet the measuring needs in batch process

  6. Influence of Fuel Meat Porosity on Heat Capacities of Fuel Element Plate U3Si2-Al

    International Nuclear Information System (INIS)

    Ginting, Aslina Br.; Supardjo; Sutri Indaryati

    2007-01-01

    Analyze of heat capacities of Al powder, AIMg 2 cladding, U 3 Si 2 powder and PEB U 3 Si 2 -Al with the meat porosity of 4.9; 5.53 ; 6.25 ; 6.95 %; 7.90; 8.66% have been done. Analysis was conducted by using Differential Scanning Calorimeter (DSC) at temperature 30℃ to 450℃ with heating rate 1℃ /minute in Argon gas media. The purpose of analyze is to know the influence of increasing of fuel meat porosity on heat capacities because increasing of percentage of meat porosity will cause degradation the of heat capacities of PEB U 3 Si 2 -Al. Result of analysis showed that the heat capacities of Al powder, AIMg 2 cladding increase by temperature, while heat capacities of U 3 Si 2 powder was stable with increasing of temperature up to 450℃. Analysis of heat capacities toward PEB U 3 Si 2 -Al indicate that increasing of fuel meat porosity of caused degradation of the heat capacities of PEB U 3 Si 2 -Al. Data obtained were expected to serve the purpose of input to fabricator of research reactor fuel in for design of fuel element type silicide with high loading. (author)

  7. Validation and uncertainty estimation of fast neutron activation analysis method for Cu, Fe, Al, Si elements in sediment samples

    International Nuclear Information System (INIS)

    Sunardi; Samin Prihatin

    2010-01-01

    Validation and uncertainty estimation of Fast Neutron Activation Analysis (FNAA) method for Cu, Fe, Al, Si elements in sediment samples has been conduced. The aim of the research is to confirm whether FNAA method is still matches to ISO/lEC 17025-2005 standard. The research covered the verification, performance, validation of FNM and uncertainty estimation. Standard of SRM 8704 and sediments were weighted for certain weight and irradiated with 14 MeV fast neutron and then counted using gamma spectrometry. The result of validation method for Cu, Fe, Al, Si element showed that the accuracy were in the range of 95.89-98.68 %, while the precision were in the range 1.13-2.29 %. The result of uncertainty estimation for Cu, Fe, Al, and Si were 2.67, 1.46, 1.71 and 1.20 % respectively. From this data, it can be concluded that the FNM method is still reliable and valid for element contents analysis in samples, because the accuracy is up to 95 % and the precision is under 5 %, while the uncertainty are relatively small and suitable for the range 95 % level of confidence where the uncertainty maximum is 5 %. (author)

  8. Investigations on thermal properties, stress and deformation of Al/SiC metal matrix composite based on finite element method

    Directory of Open Access Journals (Sweden)

    K. A. Ramesh Kumar

    2014-09-01

    Full Text Available AlSiC is a metal matrix composite which comprises of aluminium matrix with silicon carbide particles. It is characterized by high thermal conductivity (180-200 W/m K, and its thermal expansion are attuned to match other important materials that finds enormous demand in industrial sectors. Although its application is very common, the physics behind the Al-SiC formation, functionality and behaviors are intricate owing to the temperature gradient of hundreds of degrees, over the volume, occurring on a time scale of a few seconds, involving multiple phases. In this study, various physical, metallurgical and numerical aspects such as equation of continuum for thermal, stress and deformation using finite element (FE matrix formulation, temperature dependent material properties, are analyzed. Modelling and simulation studies of Al/SiC composites are a preliminary attempt to view this research work from computational point of view.

  9. Hardening mechanisms of spray formed Al-Zn-Mg-Cu alloys with scandium and other elemental additions

    International Nuclear Information System (INIS)

    Sharma, M.M.; Amateau, M.F.; Eden, T.J.

    2006-01-01

    The hardening mechanisms in spray formed Al-Zn-Mg-Cu alloys with additions of chromium, zinc and scandium were studied. The microstructure of the spray formed alloys was analyzed by transmission electron microscopy. A range of tensile strengths were achieved, and varied based on elemental additions, and second phase particle strengthening. To explain the significantly higher strength in one alloy with scandium, theoretical results due to the yield stress of Al-Zn-Mg-Cu alloys as a function of volume fraction and precipitate particle size, were compared to experimental data. Both the possibilities of coherency and order strengthening are examined. The significant additional hardening achieved in the alloy with scandium is attributed to small ordered particles of Al 3 Sc, which precipitated during aging

  10. Consolidation effects on tensile properties of an elemental Al matrix composite

    Energy Technology Data Exchange (ETDEWEB)

    Tang, F. [Building 4515, MS 6064, Metals and Ceramics Division, Oak Ridge National Lab, Oak Ridge, TN 37831 (United States)]. E-mail: tangf@ornl.gov; Meeks, H. [Ceracon Inc., 5150 Fairoaks Blvd. 01-330, Carmichael, CA 95628 (United States); Spowart, J.E. [UES Incorporated, AFRL/MLLM Building 655, 2230 Tenth St. Suite 1, Wright-Patterson AFB, OH 45433 (United States); Gnaeupel-Herold, T. [NIST Center for Neutron Research, 100 Bureau Dr. Stop 8562, Gaithersburg, MD 20899-8562 (United States); Prask, H. [NIST Center for Neutron Research, 100 Bureau Dr. Stop 8562, Gaithersburg, MD 20899-8562 (United States); Anderson, I.E. [Materials and Engineering Physics Program, Ames Laboratory, Iowa State University, Ames, IA 50011 (United States)

    2004-11-25

    In a simplified composite design, an unalloyed Al matrix was reinforced by spherical Al-Cu-Fe alloy particles (30 vol.%), using either commercial purity (99.7%) or high purity (99.99%) fine powders (diameter < 10 {mu}m). This composite material was consolidated by either vacuum hot pressing (VHP) or quasi-isostatic forging. The spatial distribution of reinforcement particles in both VHP and forged samples was shown to be almost the same by quantitative characterization with a multi-scale area fraction analysis technique. The tensile properties of all composite samples were tested and the forged materials showed significantly higher strength, while the elastic modulus values of all composite materials were close to the upper bound of theoretical predictions. Neutron diffraction measurements showed that there were high compressive residual stresses in the Al matrix of the forged samples and relatively low Al matrix residual stresses (predominantly compressive) in the VHP samples. By tensile tests and neutron diffraction measurements of the forged samples after annealing, it was shown that the high compressive residual stresses in the Al matrix were relieved and that tensile strength was also reduced to almost the same level as that of the VHP samples. Therefore, it was deduced that increased compressive residual stresses and enhanced dislocation densities in the forged composites raised the tensile strength to higher values than those of the VHP composites.

  11. Compressive Strength Evaluation in Brazed ZrO2/Ti6Al4V Joints Using Finite Element Analysis

    Science.gov (United States)

    Sharma, Ashutosh; Kee, Se Ho; Jung, Flora; Heo, Yongku; Jung, Jae Pil

    2016-05-01

    This study aims to synthesize and evaluate the compressive strength of the ZrO2/Ti-6Al-4V joint brazed using an active metal filler Ag-Cu-Sn-Ti, and its application to dental implants assuring its reliability to resist the compressive failure in the actual oral environment. The brazing was performed at a temperature of 750 °C for 30 min in a vacuum furnace under 5 × 10-6 Torr atmosphere. The microstructure of the brazed joint showed the presence of an Ag-rich matrix and a Cu-rich phase, and Cu-Ti intermetallic compounds were observed along the Ti-6Al-4V bonded interface. The compressive strength of the brazed ZrO2/Ti-6Al-4V joint was measured by EN ISO 14801 standard test method. The measured compressive strength of the joint was ~1477 MPa—a value almost five times that of existing dental cements. Finite element analysis also confirmed the high von Mises stress values. The compressive strains in the samples were found concentrated near the Ti-6Al-4V position, matching with the position of the real fractured sample. These results suggest extremely significant compressive strength in ZrO2/Ti-6Al-4V joints using the Ag-Cu-Sn-Ti filler. It is believed that a highly reliable dental implant can be processed and designed using the results of this study.

  12. Emission spectra from AlN and GaN doped with rare earth elements

    International Nuclear Information System (INIS)

    Choi, Sung Woo; Emura, Shuichi; Kimura, Shigeya; Kim, Moo Seong; Zhou Yikai; Teraguchi, Nobuaki; Suzuki, Akira; Yanase, Akira; Asahi, Hajime

    2006-01-01

    Luminescent properties of GaN and AlN based semiconductors containing rare earth metals of Gd and Dy are studied. Cathodoluminescent spectra from AlGdN show a clear and sharp peak at 318 nm following LO phonon satellites. Photoluminescence spectra from GaDyN by the above-gap excitation also show several peaks in addition to the broad luminescence band emission. For GaGdN, the sharp PL peaks are also observed at 650 and 670 nm, and they are assigned to the intra-f orbital transitions by their time decay measurements. The broad band at around 365 nm for AlGdN, 505 nm for GaGdN and GaDyN are commonly observed. The origin of these broad bands is discussed

  13. Low Z elements (Mg, Al, and Si) K-edge X-ray absorption spectroscopy in minerals and disordered systems

    Science.gov (United States)

    Ildefonse, Ph.; Calas, G.; Flank, A. M.; Lagarde, P.

    1995-05-01

    Soft X-ray absorption near edge spectroscopy (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopy have been performed at the Mg-, Al- and Si-K edges in order to establish the ability of this spectroscopy to derive structural information in disordered solids such as glasses and gels. Mg- and Al-K XANES are good structural probes to determine the coordination state of these elements in important minerals, glasses and gels. In a CaOsbnd MgOsbnd 2SiO2 glass Mg XANES spectra differ from that found in the crystalline equivalent, with a significant shift of the edge maxima to lower energy, consistent with a CN lower than 6. Mg-EXAFS on the same sample are in agreement and indicate the presence of 5-coordinated Mg with Mgsbnd O distances of 2.01Å. In aluminosilicate gels, Alsbnd K XANES has been used to investigate the [4]Al/Altotal ratios. These ratios increase as the Al/Si ratios decrease. Aluminosilicate and ferric-silicate gels were studied by using Sisbnd K edge XANES. XANES spectra differ significantly among the samples studied. Aluminosilicate gels with Al/Si= 1 present a different Al and Si local environment from that known in clay minerals with the same Al/Si ratio. The gel-to-mineral transformation thus implies a dissolution-recrystallization mechanism. On the contrary, ferric-silicate gel presents a Si local environment close to that found in nontronite which may be formed by a long range ordering of the initial gels.

  14. Study of chemical and electrochemical properties of some elements in molten NaAlCl

    International Nuclear Information System (INIS)

    Bermond, Alain

    1976-01-01

    We describe a study of the electrochemical and chemical properties in molten mixtures of Aluminium Chloride-Sodium chloride, at 210 deg. C and the concept of acidity, related to chloride activity, is previously summarized. In a first part, the study of Mercury and Cadmium by means of electro-analytical techniques, states the Hg 2+ 2 , Hg 2+ , Cd 2+ 2 and Cd 2+ ions and their acid properties. Some diagrams Equilibrium potential vs acidity are the synthesis of these results. In a second part, it is shown that a nickel electrode is an indicator of the presence of oxide ions; from interpretation of electrochemical results, O 2 appears to behave, in terms of the chloro-acido-basicity concept, as a strong di-base, giving the solvated form AlOCl - 2 , or a strong tri-base giving AlOCl. A saturation effect by Al 2 O 3 appears when the oxide concentration is increased; the solubility of Al 2 O 3 versus acidity is determined from the electrochemical results. In a third part, results for the Ni/Ni(II) or HCl/H 2 O systems are related to dissolved oxide ion presence in chloroaluminate melts; elimination of oxide ions, through H 2 O formation, by reaction with HCl is noteworthy. (author) [fr

  15. Effect of the Zr elements with thermal properties changes of U-7Mo-xZr/Al dispersion fuel

    International Nuclear Information System (INIS)

    Supardjo; Agoeng Kadarjono; Boybul; Aslina Br Ginting

    2016-01-01

    Thermal properties data of nuclear fuel is required as input data to predict material properties change phenomenon during the fabrication process and irradiated in a nuclear reactor. Study the influence of Zr element in the U-7Mo-xZr/Al (x = 1%, 2% and 3%) fuel dispersion to changes in the thermal properties at various temperatures have been stiffened. Thermal analysis includes determining the melting temperature, enthalpy, and phase changes made using Differential Thermal Analysis (DTA) in the temperature range between 30 °C up to 1400 °C, while the heat capacity of U-7Mo-xZr alloy and U-7Mo-xZr/Al dispersion fuel using Differential Scanning Calorimeter (DSC) at room temperature up to 450 °C. Thermal analyst data DTA shows that Zr levels of all three compositions showed a similar phenomenon. At temperatures between 565.60 °C - 584.98 °C change becomes α + δ to α + γ phase and at 649.22 °C – 650.13 °C happen smelting Al matrix Occur followed by a reaction between Al matrix with U-7Mo-xZr on 670.38 °C - 673.38 °C form U (Al, Mo)x Zr. Furthermore a phase change α + β becomes β + γ Occurs at temperatures 762.08 °C - 776.33 °C and diffusion between the matrix by U-7Mo-xZr/Al on 853.55 °C - 875.20 °C. Every phenomenon that Occurs, enthalpy posed a relative stable. Consolidation of uranium Occur in 1052.42 °C - 1104.99 °C and decomposition reaction of U (Al, Mo)x and U (Al, Zr)_x becomes (UAl_4, UAl_3, UAl_2), U-Mo, and UZr on 1328,34 °C - 1332,06 °C , The existence of Zr in U-Mo alloy increases the heat capacity of the U-7Mo-xZr/Al, dispersion fuel and the higher heat capacity of Zr levels increased due to interactions between the atoms of Zr with Al matrix so that the heat absorbed by the fuel increase. (author)

  16. High-uranium-loaded U3O8--Al fuel element development program

    International Nuclear Information System (INIS)

    Martin, M.M.

    1978-01-01

    The High-Uranium-Loaded U 3 O 8 --Al Fuel Development Program supports Argonne National Laboratory efforts to develop high-uranium-density research and test reactor fuel to accommodate use of low-uranium enrichment. The goal is to fuel most research and test reactors with uranium of less than 20% enrichment for the purpose of lowering the potential for diversion of highly-enriched material for nonpeaceful usages

  17. The modification of some properties of Al-2%Mg alloy by Ti &Li alloying elements

    Directory of Open Access Journals (Sweden)

    Talib Abdulameer Jasim

    2017-11-01

    Full Text Available Aluminium-Magnisium alloys are light, high strength with resistance to corrosion and good weldability. When the content of magnesium  exceeds 3% there is a tendency to stress corrosion . This work is an attempt is to prepare low density alloy with up to approximately 2.54 g / cm3 by adding different contents of Ti, and lithium to aluminum-2%Magnisium alloy. The lithium is added in two aspects, lithium chloride and pure metal. The casting performed using conventional casting method. Moreover, solution heat treatment (SHT at 520 ºC for 4 hrs, quenching in cold water, and aging at 50ºC for 4 days were done to get better mechanical properties of all samples. Microstructure was inspected by light optical microscope before and after SHT. Alloy3 which contains 1.5%Ti was tested by SEM and EDS spectrometer to exhibit the shape and micro chemical analysis of Al3Ti phase. Hardness, ultimate tensile strength, and modulus of elasticity were tested for all alloys. The results indicated that Al3Ti phase precipitates in alloys contain 0.5%T, 1%Ti, And 1.5%Ti.  The phases Al3Li as well as Al3Ti were precipitated in alloy4 which contains 2%Ti, and 2.24%Li. Mechanical properties test results also showed that the alloy4 has achieved good results, the modulus of elasticity chanced from 310.65GPa before SHT to 521.672GPa, after SHT and aging, the ultimate tensile strength was changed from 365MPa before SHT to 469MPa, after SHT and aging,  and hardness was increased from 128 to 220HV.

  18. Irradiation behavior of U 6Mn-Al dispersion fuel elements

    Science.gov (United States)

    Meyer, M. K.; Wiencek, T. C.; Hayes, S. L.; Hofman, G. L.

    2000-02-01

    Irradiation testing of U 6Mn-Al dispersion fuel miniplates was conducted in the Oak Ridge Research Reactor (ORR). Post-irradiation examination showed that U 6Mn in an unrestrained plate configuration performs similarly to U 6Fe under irradiation, forming extensive and interlinked fission gas bubbles at a fission density of approximately 3×10 27 m-3. Fuel plate failure occurs by fission gas pressure driven `pillowing' on continued irradiation.

  19. High-uranium-loaded U3O8-Al fuel element development program [contributed by N.M. Martin, ORNL

    International Nuclear Information System (INIS)

    Martin, M.M.

    1993-01-01

    The High-Uranium-Loaded U 3 O 8 -Al Fuel Element Development Program supports Argonne National Laboratory efforts to develop high-uranium-density research and test reactor fuel to accommodate use of low-uranium enrichment. The goal is to fuel most research and test reactors with uranium of less than 20% enrichment for the purpose of lowering the potential for diversion of highly-enriched material for nonpeaceful usages. The specific objective of the program is to develop the technological and engineering data base for U 3 O 8 -Al plate-type fuel elements of maximal uranium content to the point of vendor qualification for full scale fabrication on a production basis. A program and management plan that details the organization, supporting objectives, schedule, and budget is in place and preparation for fuel and irradiation studies is under way. The current programming envisions a program of about four years duration for an estimated cost of about two million dollars. During the decades of the fifties and sixties, developments at Oak Ridge National Laboratory led to the use of U 3 O 8 -Al plate-type fuel elements in the High Flux Isotope Reactor, Oak Ridge Research Reactor, Puerto Rico Nuclear Center Reactor, and the High Flux Beam Reactor. Most of the developmental information however applies only up to a uranium concentration of about 55 wt % (about 35 vol % U 3 O 8 ). The technical issues that must be addressed to further increase the uranium loading beyond 55 wt % involve plate fabrication phenomena of voids and dogboning, fuel behavior under long irradiation, and potential for the thermite reaction between U 3 O 8 and aluminum. (author)

  20. Bimetal cup hydroforming of Al/St and Cu/St composites: Adaptive finite element analysis and experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Hashemi, Abbas; Gollo, Mohammad Hoseinpour [Shahid Rajaee Teacher Training University, Tehran (Iran, Islamic Republic of); Seyedkashi, S. M. [University of Birjand, Birjand (Iran, Islamic Republic of)

    2016-05-15

    An adaptive Finite element analysis (FEA) was proposed in this paper for the industrial design of bimetal conical-cylindrical cup hydroforming. Forming circumstances for the perfect and imperfect parts were concluded through adaptive FEA using the ANSYS parametric design language. Effective parameters, including pressure loading path, layer placement order, and thickness ratio, were investigated for hydroforming of Al/St and Cu/St composite sheets. Experimental tests were implemented to validate adaptive finite element results. Rupture failure upon the pressure path occurred on the contact area between the blank and punch tip radius at low pressures and on the transition area of the conical-cylindrical portion at high pressures. The proposed method is applicable for any cylindrical, conical, or cylindrical/conical shapes with different materials and dimensions. Therefore, this method is beneficial as a practical design tool for engineers and researchers working in the process design of hydroformed shell products.

  1. Irradiation behavior of low-enriched U/sub 6/Fe-Al dispersion fuel elements

    Energy Technology Data Exchange (ETDEWEB)

    Hofman, G.L.; Domagala, R.F.; Copeland, G.L.

    1987-10-01

    An irradiation test of miniature fuel plates containing low-enriched (20% /sup 235/U)U/sub 6/Fe dispersed and clad in Al was performed. The postirradiation examination shows U/sub 6/Fe to form extensive fission gas bubbles at burnups of only approx. = 20% of the original 20% fuel enrichment. Plate failure by fission gas-driven pillowing occurred at approx. = 40% burnup. This places U/sub 6/FE at the lowest burnup capability among low enriched dispersion fuels that have been tested for use in research and test reactors

  2. Irradiation behavior of U{sub 6}Mn-Al dispersion fuel elements

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, M.K. E-mail: mitchell.meyer@anl.gov; Wiencek, T.C.; Hayes, S.L.; Hofman, G.L

    2000-04-01

    Irradiation testing of U{sub 6}Mn-Al dispersion fuel miniplates was conducted in the Oak Ridge Research Reactor (ORR). Post-irradiation examination showed that U{sub 6}Mn in an unrestrained plate configuration performs similarly to U{sub 6}Fe under irradiation, forming extensive and interlinked fission gas bubbles at a fission density of approximately 3x10{sup 27} m{sup -3}. Fuel plate failure occurs by fission gas pressure driven 'pillowing' on continued irradiation.

  3. Effects of Alloying Elements on Room and High Temperature Tensile Properties of Al-Si Cu-Mg Base Alloys =

    Science.gov (United States)

    Alyaldin, Loay

    In recent years, aluminum and aluminum alloys have been widely used in automotive and aerospace industries. Among the most commonly used cast aluminum alloys are those belonging to the Al-Si system. Due to their mechanical properties, light weight, excellent castability and corrosion resistance, these alloys are primarily used in engineering and in automotive applications. The more aluminum is used in the production of a vehicle, the less the weight of the vehicle, and the less fuel it consumes, thereby reducing the amount of harmful emissions into the atmosphere. The principal alloying elements in Al-Si alloys, in addition to silicon, are magnesium and copper which, through the formation of Al2Cu and Mg2Si precipitates, improve the alloy strength via precipitation hardening following heat treatment. However, most Al-Si alloys are not suitable for high temperature applications because their tensile and fatigue strengths are not as high as desired in the temperature range 230-350°C, which are the temperatures that are often attained in automotive engine components under actual service conditions. The main challenge lies in the fact that the strength of heat-treatable cast aluminum alloys decreases at temperatures above 200°C. The strength of alloys under high temperature conditions is improved by obtaining a microstructure containing thermally stable and coarsening-resistant intermetallics, which may be achieved with the addition of Ni. Zr and Sc. Nickel leads to the formation of nickel aluminide Al3Ni and Al 9FeNi in the presence of iron, while zirconium forms Al3Zr. These intermetallics improve the high temperature strength of Al-Si alloys. Some interesting improvements have been achieved by modifying the composition of the base alloy with additions of Mn, resulting in an increase in strength and ductility at both room and high temperatures. Al-Si-Cu-Mg alloys such as the 354 (Al-9wt%Si-1.8wt%Cu-0.5wt%Mg) alloys show a greater response to heat treatment as a

  4. Investigation of Element Effect on High-Temperature Oxidation of HVOF NiCoCrAlX Coatings

    Directory of Open Access Journals (Sweden)

    Pimin Zhang

    2018-04-01

    Full Text Available MCrAlX (M: Ni or Co or both, X: minor elements coatings have been used widely to protect hot components in gas turbines against oxidation and heat corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behavior is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y + Ru and Ce, respectively, were deposited on an Inconel-792 substrate using high velocity oxygen fuel (HVOF. The samples were subjected to isothermal oxidation tests in laboratory air at 900, 1000, and 1100 °C and a cyclic oxidation test between 100 and 1100 °C with a 1-h dwell time at 1100 °C. It was observed that the coating with Ce showed a much higher oxidation rate than the coating with Y + Ru under both isothermal and cyclic oxidation tests. In addition, the Y + Ru-doped coating showed significantly lower β phase depletion due to interdiffusion between the coating and the substrate, resulting from the addition of Ru. Simulation results using a moving phase boundary model and an established oxidation-diffusion model showed that Ru stabilized β grains, which reduced β-depletion of the coating due to substrate interdiffusion. This paper, combining experiment and simulation results, presents a comprehensive study of the influence of Ce and Ru on oxidation behavior, including an investigation of the microstructure evolution in the coating surface and the coating-substrate interface influenced by oxidation time.

  5. Segregation of solute elements at grain boundaries in an ultrafine grained Al-Zn-Mg-Cu alloy

    International Nuclear Information System (INIS)

    Sha, Gang; Yao, Lan; Liao, Xiaozhou; Ringer, Simon P.; Chao Duan, Zhi; Langdon, Terence G.

    2011-01-01

    The solute segregation at grain boundaries (GBs) of an ultrafine grained (UFG) Al-Zn-Mg-Cu alloy processed by equal-channel angular pressing (ECAP) at 200 o C was characterised using three-dimensional atom probe. Mg and Cu segregate strongly to the grain boundaries. In contrast, Zn does not always show clear segregation and may even show depletion near the grain boundaries. Trace element Si selectively segregates at some GBs. An increase in the number of ECAP passes leads to a decrease in the grain size but an increase in solute segregation at the boundaries. The significant segregation of alloying elements at the boundaries of ultrafine-grained alloys implies that less solutes will be available in the matrix for precipitation with a decrease in the average grain size. -- Research Highlights: → Atom probe tomography has been employed successfully to reveal unique segregation of solutes at ultrafine grained material. → Mg and Cu elements segregated strongly at the grain boundary of an ultrafine grained Al-Zn-Mg-Cu alloy processed by 4-pass and 8-pass ECAP at 200 o C. Zn frequently depleted at GBs with a Zn depletion region of 7-15 nm in width on one or both sides of the GBs. Only a small fraction (3/13) of GBs were observed with a low level of Zn segregation where the combined Mg and Cu excess is over 3.1 atom/nm 2 . Si appeared selectively segregated at some of the GBs. → The increase in number of ECAP passes from 4 to 8 correlated with the increase in mean level segregation of Mg and Cu for both solute excess and peak concentration. → The change of plane normal of a grain boundary within 30 o only leads to a slight change in the solute segregation level.

  6. Postirradiation Examination Of U3O8-AL Plate Type Dispersion Fuel Element

    International Nuclear Information System (INIS)

    Nasution-Hasbullah; Sugondo; Amin, D.L.; Siti-Amini

    1996-01-01

    Postirradiation examination of plate type spent fuel element RIE-01 has been carried out in order to observer its physical changes and performance under irradiation in the reactor. The irradiation has been time more than two years with a declared burnup of 51.04 %. The examination included visual and dimensional measurement, measurement of burn-up distribution, wipe test and metallographic analysis. The results showed that all fuel plates retained their integrity. The colour changes were occurred on most of the plates significant suggesting that it was generated from the oxide layer formation. From gamma-scanning examination it could be deducted that the highest burn-up distribution of the plate was at position of 30 cm from the bottom. A more homogeneous distribution was found in the middle plate of the bundle. The increased plate thickness, as revealed by dimensional measurements as in agreement with the burn-up distribution pattern. Despite the changes observed in could be concluded that all changes occurred were still within the allowable limits and therefore it can recommended that an increase of the burn-up level above 51,04 % is still quite possible

  7. A first-principles study of B2 NiAl alloyed with rare earth elements Pr, Pm, Sm, and Eu

    Institute of Scientific and Technical Information of China (English)

    He Jun-Qi; Wang You; Yan Mu-Fu; Pan Zhao-Yi; Guo Li-Xin

    2013-01-01

    The structural,elastic,and electronic properties of NiAl alloyed with rare earth elements Pr,Pm,Sm,and Eu are investigated by using density functional theory (DFT).The study suggests that Pr,Pm,Sm,and Eu all tend to be substituted for an Al site.Ni8Al7Pm possesses the largest ductility.Only the hardness and ductility of Ni8Al7Eu are enhanced simultaneously.The covalency strength of the Ni-Al bond in Ni8Al7Pm is higher than that in Ni8Al7Eu.The covalency strength of an Al-Al bond and that of a Ni-Ni bond in Ni8Al7Eu are higher than that in Ni8Al7Pm.The Ni-Pm bond and the Ni-Eu bond are covalent,and the covalency strength of the Ni-Pm bond is greater.The Al-Pm bond and the Al-Eu bond show great covalency strength and ionicity,respectively.

  8. Hierarchical finite element modeling of SiCp/Al2124 T4 composites with dislocation plasticity and size dependent failure

    International Nuclear Information System (INIS)

    Suh, Yeong Sung; Kim, Yong Bae

    2012-01-01

    The strength of particle reinforced metal matrix composites is, in general, known to be increased by the geometrically necessary dislocations punched around a particle that form during cooling after consolidation because of coefficient of thermal expansion (CTE) mismatch between the particle and the matrix. An additional strength increase may also be observed, since another type of geometrically necessary dislocation can be formed during extensive deformation as a result of the strain gradient plasticity due to the elastic plastic mismatch between the particle and the matrix. In this paper, the magnitudes of these two types of dislocations are calculated based on the dislocation plasticity. The dislocations are then converted to the respective strengths and allocated hierarchically to the matrix around the particle in the axisymmetric finite element unit cell model. the proposed method is shown to be very effective by performing finite element strength analysis of SiC p /Al2124 T4 composites that included ductile in the matrix and particle matrix decohesion. The predicted results for different particle sizes and volume fractions show that the length scale effect of the particle size obviously affects the strength and failure behavior of the particle reinforced metal matrix composites

  9. Post-irradiation examination of U3SIX-AL fuel element manufactured and irradiated in Argentina

    International Nuclear Information System (INIS)

    Ruggirello, Gabriel; Calabroni, Hector; Sanchez, Miguel; Hofman, Gerard

    2002-01-01

    As a part of CNEA's qualification program as a supplier of low enriched Al-U 3 Si 2 dispersion fuel elements for research reactors, a post irradiation examination (PIE) of the first prototype of this kind, called P-04, manufactured and irradiated in Argentina, was carried out. The main purpose of this work was to set up various standard PIE techniques in the hot cell, looking forward to the next steps of the qualification program, as well as to acquire experience on the behaviour of this nuclear material and on the control of the manufacturing process. After an appropriate cooling period, on May 2000 the P-04 was transported to the hot cell in Ezeiza Atomic Centre. Non destructive and destructive tests were performed following the PIE procedures developed in Argonne National Laboratory (ANL), this mainly included dimensional measurement, microstructural observations and chemical burn-up analyses. The methodology and results of which are outlined in this report. The results obtained show a behaviour consistent with that of other fuel elements of the same kind, tested previously. On the other hand the results of this PIE, specially those concerning burn-up analysis and stability and corrosion behaviour of the fuel plates, will be of use for the IAEA Regional Program on the characterization of MTR spent fuel. (author)

  10. Metallographic analysis of irradiated U3Si2/Al fuel element plate of 2.96 gU/cm3 density

    International Nuclear Information System (INIS)

    Maman Kartaman Ajiriyanto; Aslina Br Ginting; Junaedi

    2018-01-01

    Metallographic analysis of U 3 Si 2 /Al fuel element plate has been performed in hot cell. The purpose of metallographic analysis is to study changes in PEB U 3 Si 2 /Al microstructure and AlMg 2 cladding thickness after irradiation in reactor until burn up of 56 %. The fuel element plate of irradiated U 3 Si 2 /Al was cut in top, middle and bottom positions with each size around 5 x 5 x 1.37 mm. Metallographic preparation starts from sample cutting using cutting machine with low speed and sample mounting, grinding and polishing in hot cell 104–105. Sample mounting was done by using resin for more than 10 hours followed by grinding with sand papers up to grit size of 2400 and polishing with diamond paste of size 3 to 1 micron at a rotational speed of 150 rpm for 5 minutes. Microstructure observation was performed with optical microscope in hot cell 107 at 200 times magnification. Microstructure examination reveals U 3 Si 2 particles with inverse forms and sizes, Al matrix and AlMg 2 cladding were spread along the U 3 Si 2 /Al side. Microstructure observation of irradiated U 3 Si 2 /Al has not shown good result because only topography observation of U 3 Si 2 /Al meat, Al matrix and AlMg 2 cladding can be done due to limited capability of the optical microscope in hot cell, where maximum magnification can be attained only at 200 times so that the phenomenon of interaction layer and small gas bubble can not be observed. However, U 3 Si 2 /Al microstructure of 56 % burnup, if compared to the microstructure of U 3 Si 2 /Al fuel element plate of 60 % burnup from previous researcher, shows interaction between U 3 Si 2 meat with Al matrix and the existence of layers with a thickness about 5 up to 20 microns. Meanwhile, the observed thickness of AlMg 2 cladding is greater than 0.25 mm, which indicates that irradiation does not significantly change the thickness of AlMg 2 cladding so that the overall irradiated U 3 Si 2 -Al still has good integrity and stability. (author)

  11. Driving forces of redistribution of elements during quasicrystalline phase formation under heating of mechanically alloyed Al65Cu23Fe12 powder

    Science.gov (United States)

    Tcherdyntsev, V. V.; Kaloshkin, S. D.; Shelekhov, E. V.; Principi, G.; Rodin, A. O.

    2008-02-01

    Al65Cu23Fe12 alloys were prepared by ball milling of the elemental powders mixture. Phase and structural transformations at heating of as-milled powders were investigated by X-ray diffraction analysis. Precision analysis of Mössbauer spectra was performed to check the adequacy of the fitting of X-ray diffraction patterns. The results were compared with the data of differential scanning and solution calorimetry, as well as with the thermodynamic literature data, in order to estimate the driving forces of redistribution of elements that preceded the formation of single-phase quasicrystalline structure. The heat of elements mixing, which is positive for Cu-Fe system and negative for Al-Fe and Al-Cu systems, was supposed to be a decisive factor for phase transformations during heating of the alloy. The correlation between sequence of phase transformations during heating and the thermodynamic data was discussed and the scheme describing phase transformations observed was proposed.

  12. DETERMINATION OF LIMIT DETECTION OF THE ELEMENTS N, P, K, Si, Al, Fe, Cu, Cd, WITH FAST NEUTRON ACTIVATION USING NEUTRON GENERATOR

    OpenAIRE

    Sunardi, Sunardi; Muryono, Muryono

    2010-01-01

    Determination of limit detection of the elements N, P, K, Si, Al, Fe, Cu, Cd, with fast neutron activation using neutron generator has been done.  Samples prepared from SRM 2704, N, P, K elements from MERCK, Cu, Cd, Al from activation foil made in San Carlos, weighted and packed for certain weight then iradiated during 30 minutes with 14 MeV fast neutron using the neutron generator and then counted with gamma spectrometry (accuspec).  At this research condition of neutron generator was set at...

  13. Effects of Alloying Elements on the Formation of Core-Shell-Structured Reinforcing Particles during Heating of Al-Ti Powder Compacts.

    Science.gov (United States)

    Chen, Tijun; Gao, Min; Tong, Yunqi

    2018-01-15

    To prepare core-shell-structured Ti@compound particle (Ti@compound p ) reinforced Al matrix composite via powder thixoforming, the effects of alloying elements, such as Si, Cu, Mg, and Zn, on the reaction between Ti powders and Al melt, and the microstructure of the resulting reinforcements were investigated during heating of powder compacts at 993 K (720 °C). Simultaneously, the situations of the reinforcing particles in the corresponding semisolid compacts were also studied. Both thermodynamic analysis and experiment results all indicate that Si participated in the reaction and promoted the formation of Al-Ti-Si ternary compounds, while Cu, Mg, and Zn did not take part in the reaction and facilitated Al₃Ti phase to form to different degrees. The first-formed Al-Ti-Si ternary compound was τ1 phase, and then it gradually transformed into (Al,Si)₃Ti phase. The proportion and existing time of τ1 phase all increased as the Si content increased. In contrast, Mg had the largest, Cu had the least, and Si and Zn had an equivalent middle effect on accelerating the reaction. The thicker the reaction shell was, the larger the stress generated in the shell was, and thus the looser the shell microstructure was. The stress generated in (Al,Si)₃Ti phase was larger than that in τ1 phase, but smaller than that in Al₃Ti phase. So, the shells in the Al-Ti-Si system were more compact than those in the other systems, and Si element was beneficial to obtain thick and compact compound shells. Most of the above results were consistent to those in the semisolid state ones except the product phase constituents in the Al-Ti-Mg system and the reaction rate in the Al-Ti-Zn system. More importantly, the desirable core-shell structured Ti@compound p was only achieved in the semisolid Al-Ti-Si system.

  14. Measuring the Extent of the Environmental Pollution in the Waters of the Al-Diwani River by Certain Trace Elements Resulting from Al-Diwani Textile Factory Using Spectroscopic Methods

    Directory of Open Access Journals (Sweden)

    Al-Rufaie Mohauman Mahammad

    2016-04-01

    Full Text Available The textile industry is a key source of pollution in fresh water. The concentration of key heavy metal pollutants (cobalt, nickel, lead, mercury, cadmium, copper, and iron as well as pH value and conductivity were measured in water samples taken from the input and output (waste water of Al-Diwani textile factory on the Al-Diwani River, Iraq. These samples were measured using two methods, flame atomic absorption spectrophotometry and spectrometry. This paper considers the relative effectiveness of each method for measuring the concentrations of the elements, and discusses which method is best for which element. It was found that the first method is more accurate for measuring the concentrations for all elements except iron.

  15. Investigations into the corrosion resistance of copper aluminium alloys. Effect of phosphorus as corrosion resistant third alloying element in the ternary system CuAl20P1

    International Nuclear Information System (INIS)

    Allwardt, A.

    1997-01-01

    The effect of phosphorus on the corrosion resistance of Al-bronzes is studied in detail in this work. A literature review showed that there are a lot of things known about the microstructure and the mechanical properties of Al-bronzes. In spite of their corrosion resistance the corrosion properties and the structure of the protective oxide films of Al-bronzes were seldom a matter of interest. Systematic studies of the influence of different alloying elements on the oxide film and the corrosion properties are rare. Therefore, it is not possible to predict the corrosion resistance of Al-bronzes, made by alloying particular elements. The high corrosion resistance of the new alloy CuAl 20 P 1 was the reason to investigate the influence of phosphorus on the corrosion properties of Al-bronzes in more detail. A systematic study of the microstructure and the corrosion properties of Cu, CuP x , CuAl 20 and CuAl 20 P x offers an insight into the effect of aluminium and phosphorus on the formation of the oxide film on Al-bronzes. It was found that there exists a critical amount of 1 at.-% of phosphorus. Above and below this amount the corrosion resistance becomes worse. This behaviour could be explained by XPS-and electrochemical measurements. Although there are still some questions about the influence of phosphorus on the corrosion resistance of Al-bronzes, this work has produced some important results, which in the future may be helpful to develop new high corrosion resistant Al-bronzes more efficiently: - on clean surface Al-bronze, the oxidation of Al and Cu takes place simultaneously, - Al promotes the formation of Cu 2 O but impedes the formation of Cu(II)-oxide/-hydride in neutral solutions, - P impedes the formation of Cu 2 O and as a consequence promotes the formation of aluminium oxide. This results in a higher amount of Al in the oxide film on the surface of the alloy, which leads to a better corrosion resistance. (author) figs., tabs., 106 refs

  16. Anomalous decrease in X-ray diffraction intensities of Cu-Ni-Al-Co-Cr-Fe-Si alloy systems with multi-principal elements

    International Nuclear Information System (INIS)

    Yeh, J.-W.; Chang, S.-Y.; Hong, Y.-D.; Chen, S.-K.; Lin, S.-J.

    2007-01-01

    With an aim to understand the great reduction in the X-ray diffraction (XRD) intensities of high-entropy alloys, a series of Cu-Ni-Al-Co-Cr-Fe-Si alloys with systematic addition of principal elements from pure element to seven elements was investigated for quantitative analysis of XRD intensities. The variation of XRD peak intensities of the alloy system is similar to that caused by thermal effect, but the intensities further drop beyond the thermal effect with increasing number of incorporated principal elements. An intrinsic lattice distortion effect caused by the addition of multi-principal elements with different atomic sizes is expected for the anomalous decrease in XRD intensities. The mathematical factor of this distortion effect for the modification of XRD structure factor is formulated analogue to that of thermal effect

  17. Application of the TXRT method for the elemental analysis of the cerebrospinal fluid (CSF) and serum in amyotrophic lateral sclerosis (ALS)

    International Nuclear Information System (INIS)

    Ostachowicz, B.; Lankosz, M.; Tomik, B.; Adamek, D.; Wobrauschek, P.; Streli, C.; Kregsamer, P.

    2005-01-01

    Specific analysis of the chemical constituents of body fluids can be useful as a diagnostic procedure for some neurological diseases. With respect to neurodegenerative processes it is important to know if abnormalities of selected elements are observed in body fluids. In the present study the Total Reflection X-Ray Fluorescence (TXRF) spectrometry was applied for elemental analysis of cerebrospinal fluid (CSF) and serum as a part of the investigation on the role of the elements in Amyotrophic Lateral Sclerosis (ALS). The pathogenesis of this neurodegenerative disorder is still not well understood. Some imbalance in the concentrations of elemental composition of the body fluids can indicates some pathological processes in the human body. For that reason analysis of the elements, especially metallic ones should be performed. TXRF method is a multielement technique with significantly improved detection limits compared to conventional EDXRF. Therefore, this method can be applied for direct elemental analyses of CSF and serum. For the measurements the EXTRA II spectrometer (Atomic Institute in Vienna) and multifunctional X-ray system, both equipped with Mo-anode diffraction X-ray tube were used. The light elements - Na and Mg were measured in Atomic Institute in Vienna with Cr-X-ray tube in vacuum chamber and ultrathin window detector. The samples from the ALS and control group obtained previously for the routine diagnostic procedures and kept in deep freezer in sterile, chemically inert containers, were used for the investigations. The following elements were determined in serum and CSF: Na, Mg, CI, K, Ca, Cu, Zn, Br. The accuracy of the method was checked using Certified Reference Material, A-13 (freeze-dried animal blood) and Serum SRM MIO 181. The detection limits were calculated for both applied spectrometers. The results of both body fluids were analysed with the t-test to check the differences between ALS and control groups. (author)

  18. Phase transformation and magnetic properties of MnAl powders prepared by elemental-doping and salt-assisted ball milling

    Science.gov (United States)

    Qian, Hui-Dong; Si, Ping-Zhan; Choi, Chul-Jin; Park, Jihoon; Cho, Kyung Mox

    2018-05-01

    The effects of elemental doping of Si and Fe on the ɛ→τ phase transformation and the magnetic properties of MnAl were studied. The magnetic powders of Si- and Fe-doped MnAl were prepared by using induction melting followed by water-quenching, annealing, and salt-assisted ball-milling. The Fe-doped MnAl powders are mainly composed of the L10-structured τ-phase, while the Si-doped MnAl are composed of τ-phase and a small fraction of γ2- and β-phases. A unique thin leaves-like morphology with thickness of several tens of nanometers and diameter size up to 500 nm were observed in the Si-doped MnAl powders. The Fe-doped MnAl powders show irregular shape with much larger dimensions in the range from several to 10 μm. The morphology difference of the samples was ascribed to the variation of the mechanical properties affected by different doping elements. The phase transformation temperatures of the ɛ-phase of the samples were measured. The doping of Fe decreases the onset temperature of the massive phase transformation in MnAl, while the Si-doping increases the massive phase transformation temperature. Both Fe and Si increase the Curie temperature of MnAl. A substantially enhanced coercivity up to 0.45 T and 0.42 T were observed in the ball-milled MnAl powders doped with Si and Fe, respectively.

  19. Study on the fabrication of Al matrix composites strengthened by combined in-situ alumina particle and in-situ alloying elements

    International Nuclear Information System (INIS)

    Huang Zanjun; Yang Bin; Cui Hua; Zhang Jishan

    2003-01-01

    A new idea to fabricate aluminum matrix composites strengthened by combined in-situ particle strengthening and in-situ alloying has been proposed. Following the concept of in-situ alloying and in-situ particle strengthening, aluminum matrix composites reinforced by Cu and α-Al 2 O 3 particulate (material I) and the same matrix reinforced by Cu, Si alloying elements and α-Al 2 O 3 particulate (material II) have been obtained. SEM observation, EDS and XRD analysis show that the alloy elements Cu and Si exist in the two materials, respectively. In-situ Al 2 O 3 particulates are generally spherical and their mean size is less than 0.5 μm. TEM observation shows that the in-situ α-Al 2 O 3 particulates have a good cohesion with the matrix. The reaction mechanism of the Al 2 O 3 particulate obtained by this method was studied. Thermodynamic considerations are given to the in-situ reactions and the distribution characteristic of in-situ the α-Al 2 O 3 particulate in the process of solidification is also discussed

  20. The impact of major alloying elements and refiner on the SDAS of Al-Si-Cu alloy; Der Einfluss von Hauptlegierungselementen und Kornfeinern auf den sekundaeren Dendritenarmabstand der Al-Si-Cu-Legierung

    Energy Technology Data Exchange (ETDEWEB)

    Djurdjevic, Mile; Byczynski, Glenn [Nemak Europe GmbH, Frankfurt am Main (Germany). Frankfurt Airport Center 1; Pavlovic, Jelena [Magdeburg Univ. (Germany). Inst. fuer Fertigungstechnik und Qualitaetssicherung

    2009-02-15

    This paper investigates the effect of some major alloying elements (silicon and copper) and the effect of grain refiner (titanium boride) on the size of the secondary dendrite arm spacing (SDAS) in series of Al-Si-Cu alloys. It has been shown that both silicon and copper have significant influence on this solidification parameter. The addition of grain refining master alloys to aluminium alloys is common practice in many commercial foundries aiming to reduce the grain size of Al-Si alloys. However, it was shown in the present paper that master alloy based on TiB had an unexpected impact on the SDAS, decreasing the size of SDAS. In addition, there is a minimum of SDAS corresponding to the presence of 0.12 wt% of titanium in Al-Si alloy. Such findings could have important implications for Al-Si alloys in particular, due to their wide spread applications in the automotive industry. (orig.)

  1. Research on Zr50Al15-xNi10Cu25Yx amorphous alloys prepared by mechanical alloying with commercial pure element powders

    International Nuclear Information System (INIS)

    Long Woyun; Ouyang Xueqiong; Luo Zhiwei; Li Jing; Lu Anxian

    2011-01-01

    Amorphous Zr 50 Al 15-x Ni 10 Cu 25 Y x alloy powders were fabricated by mechanical alloying at low vacuum with commercial pure element powders. The effects on glass forming ability of Al partial substituted by Y in Zr 50 Al 15 Ni 10 Cu 25 and thermal stability of Si 3 N 4 powders addition were investigated. The as-milled powders were characterized by X-ray diffraction, scanning electron microscopy and differential scanning calorimeter. The results show that partial substitution of Al can improve the glass forming ability of Zr 50 Al 15 Ni 10 Cu 25 alloy. Minor Si 3 N 4 additions raise the crystallization activation energy of the amorphous phase and thus improve its thermal stability. -- Research Highlights: → ZrAlNiCu amorphous alloys can be synthesized by MA in low cost. → Appropriate amount of Al substituted by Y in ZrAlNiCu alloy can improve its glass forming ability. → A second phase particle addition helps to improve the thermal stability of the amorphous matrix.

  2. Imaging of glial cell morphology, SOD1 distribution and elemental composition in the brainstem and hippocampus of the ALS hSOD1G93A rat.

    Science.gov (United States)

    Stamenković, Stefan; Dučić, Tanja; Stamenković, Vera; Kranz, Alexander; Andjus, Pavle R

    2017-08-15

    Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disorder affecting motor and cognitive domains of the CNS. Mutations in the Cu,Zn-superoxide dismutase (SOD1) cause 20% of familial ALS and provoke formation of intracellular aggregates and copper and zinc unbinding, leading to glial activation and neurodegeneration. Therefore, we investigated glial cell morphology, intracellular SOD1 distribution, and elemental composition in the brainstem and hippocampus of the hSOD1 G93A transgenic rat model of ALS. Immunostaining for astrocytes, microglia and SOD1 revealed glial proliferation and progressive tissue accumulation of SOD1 in both brain regions of ALS rats starting already at the presymptomatic stage. Glial cell morphology analysis in the brainstem of ALS rats revealed astrocyte activation occurring before disease symptoms onset, followed by activation of microglia. Hippocampal ALS astrocytes exhibited an identical reactive profile, while microglial morphology was unchanged. Additionally, ALS brainstem astrocytes demonstrated progressive SOD1 accumulation in the cell body and processes, while microglial SOD1 levels were reduced and its distribution limited to distal cell processes. In the hippocampus both glial cell types exhibited SOD1 accumulation in the cell body. X-ray fluorescence imaging revealed decreased P and increased Ca, Cl, K, Ni, Cu and Zn in the brainstem, and higher levels of Cl, Ni and Cu, but lower levels of Zn in the hippocampus of symptomatic ALS rats. These results bring new insights into the glial response during disease development and progression in motor as well as in non-motor CNS structures, and indicate disturbed tissue elemental homeostasis as a prominent hallmark of disease pathology. Copyright © 2017 IBRO. Published by Elsevier Ltd. All rights reserved.

  3. DETERMINATION OF LIMIT DETECTION OF THE ELEMENTS N, P, K, Si, Al, Fe, Cu, Cd, WITH FAST NEUTRON ACTIVATION USING NEUTRON GENERATOR

    Directory of Open Access Journals (Sweden)

    Sunardi Sunardi

    2010-06-01

    Full Text Available Determination of limit detection of the elements N, P, K, Si, Al, Fe, Cu, Cd, with fast neutron activation using neutron generator has been done.  Samples prepared from SRM 2704, N, P, K elements from MERCK, Cu, Cd, Al from activation foil made in San Carlos, weighted and packed for certain weight then iradiated during 30 minutes with 14 MeV fast neutron using the neutron generator and then counted with gamma spectrometry (accuspec.  At this research condition of neutron generator was set at current 1 mA that produced neutron flux about 5,47.107 n/cm2.s and  experimental result shown that the limit detection for the elements N, P, K, Si, Al, Fe, Cu, Cd are  2,44 ppm, 1,88 ppm, 2,15 ppm, 1,44 ppm, 1,26 ppm, 1,35 ppm, 1,05 ppm, 2,99 ppm, respectively.  The data  indicate that the limit detection or sensitivity of appliance of neutron generator to analyze the element is very good, which is feasible to get accreditation AANC laboratory using neutron generator.   Keywords: limit detection, AANC, neutron generator

  4. Use of environmental isotope techniques in studying surface and groundwaters in the Damascus basin (Al-Ghotta): A case study of geochemical modeling of elements and pollutants transport

    International Nuclear Information System (INIS)

    Kattan, Z.

    2004-09-01

    This work discuses in details the hydrochemical and isotopic characteristics of surface and groundwaters in the Damascus Ghotta basin. In addition, it deals with the chemical and isotopic compositions of rainfall of some surrounding stations (Damascus, Bloudan, Arneh, Al-Kounietra, Izraa, Al-Souweida, Homs and Tartous). The objective of this research was to make new assessment of the available water resources in this basin, together with conducting essays to model geochemically the elements and pollutants transport in the groundwater, by the use of PHREEQM code.(author)

  5. Survey of trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) in retail samples of flavoured and bottled waters.

    Science.gov (United States)

    Barroso, M F; Ramos, S; Oliva-Teles, M T; Delerue-Matos, C; Sales, M G F; Oliveira, M B P P

    2009-01-01

    Concentrations of eleven trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) were measured in 39 (natural and flavoured) water samples. Determinations were performed using graphite furnace electrothermetry for almost all elements (Al, As, Cd, Cr, Co, Mn, Ni, Pb, and Si). For Se determination hydride generation was used, and cold vapour generation for Hg. These techniques were coupled to atomic absorption spectrophotometry. The trace element content of still or sparkling natural waters changed from brand to brand. Significant differences between natural still and natural sparkling waters (p element was compared with the presence of flavours, preservatives, acidifying agents, fruit juice and/or sweeteners, according to the labelled composition. It was shown that flavoured waters generally increase the trace element content. The addition of preservatives and acidifying regulators had a significant influence on Mn, Co, As and Si contents (p < 0.05). Fruit juice can also be correlated to the increase of Co and As. Sweeteners did not provide any significant difference in Mn, Co, Se and Si content.

  6. The effect of major alloying elements on the size of the secondary dendrite arm spacing in the as-cast Al-Si-Cu alloys

    Directory of Open Access Journals (Sweden)

    M. B. Djurdjevič

    2012-01-01

    Full Text Available A comprehensive understanding of melt quality is of paramount importance for the control and prediction of actual casting characteristics. Among many phenomenons that occur during the solidification of castings, there are four that control structure and consequently mechanical properties: chemical composition, liquid metal treatment, cooling rate and temperature gradient. The cooling rate and alloy composition are among them most important. This paper investigates the effect of some major alloying elements (silicon and copper of Al-Si-Cu alloys on the size of the secondary dendrite arm spacing. It has been shown that both alloying elements have reasonable influence on the refinement of this solidification parameter.

  7. Uncertainty evaluation in correlated quantities: application to elemental analysis of atmospheric aerosols;Evaluacion de la incertidumbre en cantidades correlacionadas: aplicacion al analisis elemental de aerosoles atmosfericos

    Energy Technology Data Exchange (ETDEWEB)

    Espinosa, A.; Miranda, J.; Pineda, J. C., E-mail: miranda@fisica.unam.m [UNAM, Instituto de Fisica, Circuito de la Investigacion Cientifica s/n, Ciudad Universitaria, 04510 Mexico D. F. (Mexico)

    2010-07-01

    One of the aspects that are frequently overlooked in the evaluation of uncertainty in experimental data is the possibility that the involved quantities are correlated among them, due to different causes. An example in the elemental analysis of atmospheric aerosols using techniques like X-ray Fluorescence (X RF) or Particle Induced X-ray Emission (PIXE). In these cases, the measured elemental concentrations are highly correlated, and then are used to obtain information about other variables, such as the contribution from emitting sources related to soil, sulfate, non-soil potassium or organic matter. This work describes, as an example, the method required to evaluate the uncertainty in variables determined from correlated quantities from a set of atmospheric aerosol samples collected in the Metropolitan Area of the Mexico Valley and analyzed with PIXE. The work is based on the recommendations of the Guide for the Evaluation of Uncertainty published by the International Organization for Standardization. (Author)

  8. Status report on the irradiation testing and post-irradiation examination of low-enriched U3O8-Al and UAlsub(x)-Al fuel element by the Netherlands Energy Research Foundation (ECN)

    International Nuclear Information System (INIS)

    Pruimboom, H.; Lijbrink, E.; Otterdijk, K. von; Swanenburg de Veye, R.J.

    1984-01-01

    Within the framework of the RERTR-programme four low-enriched (20%) MTR-type fuel elements have been irradiated in the High Flux Reactor at Petten (The Netherlands) and are presently subjected to postirradiation examination. Two of the elements contain UAlsub(x)-Al and two contain U 3 O 8 -Al fuel. The test irradiation has been completed up to the target burn-up values of 50% and 75% respectively. An extensive surveillance programme carried out during the test period has confirmed the excellent in-reactor behaviour of both types. Post-irradiation examination of the 50% burn-up test elements, comprising of dimensional measurements, burn-up determination, fuel metallography and blister testing, has sofar confirmed the irradiation experiences. Good agreement between calculated and measured power and burn-up characteristics has been found. A survey of the test element characteristics, their irradiation history, the irradiation tests and the preliminary PIE results is given in the paper. (author)

  9. Simulation of thermal stresses in SiC-Al2O3 composite tritium penetration barrier by finite-element analysis

    International Nuclear Information System (INIS)

    Liu, Hongbing; Tao, Jie; Gautreau, Yoann; Zhang, Pingze; Xu, Jiang

    2009-01-01

    Tritium penetration barrier (TPB) composed of Al 2 O 3 and SiC on 316L stainless steel was proposed to improve the tritium penetration resistance of the substrate in this work. At the same time, the concept of functionally graded materials (FGM) was applied to manage to decrease residual stresses between Al 2 O 3 and 316L stainless steel substrate due to the mismatch of their thermal expansion coefficients. The effects of system architecture on the residual stresses developed in the composite coatings were investigated numerically by means of finite-element analysis (FEA). Modeling results showed that the presence of the graded properties and the compositions within the coating did reduce the stress discontinuity at the interfaces between the coating and the substrate. Also, the magnitudes of the residual stresses on the coating surface and at the coating/substrate interface were dependent on the Al 2 O 3 and SiC coating thickness.

  10. Navigation and offshore wind turbine arrays in the North Sea. Construction of deformable protective elements; Schifffahrt und Offshore-Windenergieanlagen in der Nordsee. Vorgelagerte Elemente als Knautschzone

    Energy Technology Data Exchange (ETDEWEB)

    Otte, Erhard

    2010-11-29

    With the construction of many new offshore wind turbines, the risk of collisions in the German part of the North Sea will increase considerably. While the collision risk can be reduced by specifying priority and safety zones, it cannot be reduced to nil. It is therefore necessary to take measures to reduce the consequences of potential collisions. The author proposes the construction of deformable elements around wind turbines which may also serve as wave energy plants. This will not only reduce the collision shock but may also make the system more profitable and give it political, economic and ecological advantages. (orig.)

  11. Carbone_et_al_2016_ambient_data - Sea surface temperature variation linked to elemental mercury concentrationsmeasured on Mauna Loa

    Data.gov (United States)

    U.S. Environmental Protection Agency — This data set has two sets of gaseous elemental mercury data. The first column contains all Hg related data some of which may have been affected by the upslope...

  12. A comparative study on the sintering and casting of a blended elemental Ti-6Al-4V alloy

    CSIR Research Space (South Africa)

    Masikane, M

    2015-07-01

    Full Text Available Over the past years, the blended elemental powder metallurgy (PM) approach has been identified as one of the most promising strategies to reduce the cost of titanium-based components. However, oxygen pick-up, inhomogeneity of the microstructure...

  13. Coordination behaviour of some f-block elements with o-vanillin and its derivatives (Paper No. AL-09)

    International Nuclear Information System (INIS)

    Agarwala, B.V.; Shukla, M.K.; Hingorani, S.

    1990-02-01

    Five new complexes of La(III), Ce(III) and UO 2 have been prepared with o-vanillin and its derivatives. Their coordination behaviour and structural elucidation have been described by elemental, magnetic moments, IR, electronic spectral and thermal studies. (author). 1 tab

  14. Growth and radioluminescence of metal elements doped LiCaAlF.sub.6./sub. single crystals for neutron scintillator

    Czech Academy of Sciences Publication Activity Database

    Tanaka, Ch.; Yokota, Y.; Kurosawa, S.; Yamaji, A.; Jarý, Vítězslav; Babin, Vladimir; Pejchal, Jan; Ohashi, Y.; Kamada, K.; Nikl, Martin; Yoshikawa, A.

    2016-01-01

    Roč. 90, Jul (2016), s. 170-173 ISSN 1350-4487. [International Conference on Luminescent Detectors and Transformers of Ionizing Radiation (LUMDETR). Tartu (Estonsko), 20.09.2015-25.09.2015] R&D Projects: GA MŠk(CZ) LH14266 Institutional support: RVO:68378271 Keywords : neutron scintillator * LiCaAlF 6 * Pb2+ * single crystal Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.442, year: 2016

  15. Effects of alloying elements (Mn, Co, Al, W, Sn, B, C and S) on biodegradability and in vitro biocompatibility of pure iron.

    Science.gov (United States)

    Liu, B; Zheng, Y F

    2011-03-01

    Pure iron was determined to be a valid candidate material for biodegradable metallic stents in recent animal tests; however, a much faster degradation rate in physiological environments was desired. C, Mn, Si, P, S, B, Cr, Ni, Pb, Mo, Al, Ti, Cu, Co, V and W are common alloying elements in industrial steels, with Cr, Ni, Mo, Cu, Ti, V and Si being acknowledged as beneficial in enhancing the corrosion resistance of iron. The purpose of the present work (using Fe-X binary alloy models) is to explore the effect of the remaining alloying elements (Mn, Co, Al, W, B, C and S) and one detrimental impurity element Sn on the biodegradability and biocompatibility of pure iron by scanning electron microscopy, X-ray diffraction, metallographic observation, tensile testing, microhardness testing, electrochemical testing, static (for 6 months) and dynamic (for 1 month with various dissolved oxygen concentrations) immersion testing, cytotoxicity testing, hemolysis and platelet adhesion testing. The results showed that the addition of all alloying elements except for Sn improved the mechanical properties of iron after rolling. Localized corrosion of Fe-X binary alloys was observed in both static and dynamic immersion tests. Except for the Fe-Mn alloy, which showed a significant decrease in corrosion rate, the other Fe-X binary alloy corrosion rates were close to that of pure iron. It was found that compared with pure iron all Fe-X binary alloys decreased the viability of the L929 cell line, none of experimental alloying elements significantly reduced the viability of vascular smooth muscle cells and all the elements except for Mn increased the viability of the ECV304 cell line. The hemolysis percentage of all Fe-X binary alloy models were less than 5%, and no sign of thrombogenicity was observed. In vitro corrosion and the biological behavior of these Fe-X binary alloys are discussed and a corresponding mechanism of corrosion of Fe-X binary alloys in Hank's solution proposed. As a

  16. Mechanical properties of Al2 O3 Zr O2 layered ceramic composite and finite element application

    International Nuclear Information System (INIS)

    Ahmed, Kh.; Meriani, S.

    1997-01-01

    A three-layered structure has been fabricated using colloidal techniques combined with sequential centrifuging of the slurries to consolidate the layers. The outer layers are of alumina containing various amounts of zirconia while the inner layer contains mainly zirconia with small amount of alumina. The same technique could be also used in the coating of the spherical fuel of the high temperature gas cooled reactor (HTR). Periodic parallel cracks in the inner layer, orthogonal to the layer interface have been observed in the specimens after cooling from 1550 degree C. The finite element method (FEM) have been used to analyze this phenomenon which could be established as a result of the thermal expansion mismatch between the three layers. The general finite element package ALGOR have been used in the analysis. 5 figs., 1 tab

  17. First-principles study of new quaternary Heusler compounds without 3d transition metal elements: ZrRhHfZ (Z = Al, Ga, In)

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaotian [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China); Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Cheng, Zhenxiang, E-mail: cheng@uow.edu.au [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Guo, Ruikang [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China); Wang, Jianli [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Rozale, Habib [Condensed Matter and Sustainable Development Laboratory, Physics Department, University of Sidi-Bel-Abbès, 22000 Sidi-Bel-Abbès (Algeria); Wang, Liying [Department of Physics, Tianjin University, Tianjin 300350 (China); Yu, Zheyin [Institute for Superconducting & Electronic Materials (ISEM), University of Wollongong, Wollongong 2500 (Australia); Liu, Guodong, E-mail: gdliu1978@126.com [School of Material Sciences and Engineering, Hebei University of Technology, Tianjin 300130 (China)

    2017-06-01

    Plane-wave pseudo-potential methods based on density functional theory are employed to investigate the electronic structures, and the magnetic and half-metallic properties of the newly designed quaternary Heusler compounds ZrRhHfZ (Z = Al, Ga, In) without 3d transition metal elements. The calculated results show that ZrRhHfZ (Z = Al, Ga, In) compounds are half-metallic, with 100% spin polarization around the Fermi level. The structural stability of these compounds has been tested from the aspects of their cohesion energy and formation. The spin-flip/half-metallic gaps of ZrRhHfZ (Z = Al, Ga, In) compounds are quite large, with values of 0.2548 eV, 0.3483 eV, and 0.2866 eV, respectively. These compounds show Slater-Pauling behavior, and the total spin magnetic moment per unit cell (M{sub t}) scales with the total number of valence electrons (Z{sub t}) following the rule: M{sub t} = Z{sub t} - 18. The magnetization of ZrRhHfZ (Z = Al, Ga, In) compounds mainly comes from the 4d electrons of the Zr atoms and the 5d electrons of the Hf atoms. Furthermore, the effects of uniform strain and tetragonal deformation on the half metallicity has been investigated in detail, which is important for practical application. Finally, we reveal that the half-metallicity can be maintained when the Coulomb interactions are considered. - Highlights: • New quaternary compounds without 3d transition metal elements have been designed. • The electronic structures and magnetism of the ZrRhHfZ compounds have been studied. • The effect of strain on the half-metallic behavior has been tested. • The effect of the Coulomb interactions on the half-metallicity has been investigated.

  18. A study on the influence of trace elements (C, S, B, Al, N) on the hot ductility of the high purity austenitic alloy Fe-Ni 36% (INVAR)

    Energy Technology Data Exchange (ETDEWEB)

    Simonetta-Perrot, M T

    1994-11-01

    In order to study the damage mechanisms leading to the ductility decrease of the Invar alloy at 600 C, a high-purity Fe-Ni 36% sample has been doped with trace elements with the purpose of identifying the role of sulfur, sulfur with Al N or B N precipitates and sulfur with boron, on the ductility, the failure modes, the intergranular damage and the plastic deformation mechanisms prior to failure. A new AES segregation quantification method has been used to study the kinetics and thermodynamics of intergranular and surface segregations and determine the relation between sulfur segregation and grain joint fragility. refs., figs., tabs.

  19. The effect of Ca and RE elements on the precipitation kinetics of Mg17Al12 phase during artificial aging of magnesium alloy AZ91

    International Nuclear Information System (INIS)

    Amir Esgandari, B.; Mehrjoo, H.; Nami, B.; Miresmaeili, S.M.

    2011-01-01

    Highlights: → Ca and RE elements decrease the precipitation rate during aging of AZ91 alloy. → Precipitation kinetics and mechanism during aging of the alloys were studied. → Effect of Ca and RE on creep properties of age hardened AZ91 alloy was studied. - Abstract: The effect of simultaneous alloying with Ca and rare earth (RE) elements on the age hardening kinetics of AZ91 was studied through the fitting of the Johnson-Mehl-Avrami (JMA) equation. The results showed that the addition of both Ca and RE elements not only suppress discontinuous precipitation of the Mg 17 Al 12 phase during the age hardening process, but also decrease the alloy hardness. Fitting the JMA equation to the experimental data indicated that the phase transformation during age hardening of an alloy variant containing both Ca and RE (at 170 deg. C and 190 deg. C) and standard AZ91 (at 170 deg. C) takes place by the nucleation of precipitates on dislocations. In contrast, the precipitation during age hardening of AZ91 at 190 deg. C occurs via nucleation at grain boundaries. Although it was observed that the creep strength of age hardened specimens are lower than that of the as cast specimens, but age hardening treatment has lower deleterious influence on the creep resistance of the alloy containing Ca and RE in comparison with conventional AZ91. This may be ascribed to the decreased precipitation rate resulting from the addition of both Ca and RE elements.

  20. SEM in situ MiniCantilever Beam Bending of U-10Mo/Zr/Al Fuel Elements

    Energy Technology Data Exchange (ETDEWEB)

    Mook, William [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Baldwin, Jon K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Ricardo M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mara, Nathan A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-06-16

    In this work, the fracture behavior of Al/Zr and Zr/dU-10Mo interfaces was measured via the minicantilever bend technique. The energy dissipation rates were found to be approximately 3.7-5 mj/mm2 and 5.9 mj/mm2 for each interface, respectively. It was found that in order to test the Zr/U-10Mo interface, location of the hinge of the cantilever was a key parameter. While this test could be adapted to hot cell use through careful alignment fixturing and measurement of crack lengths with an optical microscope (as opposed to SEM, which was used here out of convenience), machining of the cantilevers via MiniMill in such a way as to locate the interfaces at the cantilever hinge, as well as proper placement of a femtosecond laser notch will continue to be key challenges in a hot cell environment.

  1. Geochemical and radiometric surveys of Sabkhet Al-Jaboul area by investigating trace elements, radon measurements and gamma spectrometry

    International Nuclear Information System (INIS)

    Jubeli, Y.; Aissa, M.; Al-Hilal, M.

    1999-08-01

    Radiometric and geochemical surveys were carried out over various geological formations in Sabkhet Al-Jaboul and its surrounding environment for evaluating the levels of radioactivity in the area. Therefore, a number of exploration techniques were used in this study such as gamma ray spectrometry, geochemical exploration and soil radon measurements. Although the results of this survey indicate some slight variations of which might be useful to distinguish between various lithological units, most of the obtained data do not reveal any significant radiometric values that could be considered important from the exploration point of view. However, these data were successfully handled to estimate the natural background of radioactivity throughout the geological units of the region. The results also showed the importance of the sedimentary transition contact zone where the continental fresh and salt favourable geochemical environment for uranium precipitation when other fundamental geological requirements for developing such concentrations are available. (author)

  2. High Temperature Oxidation Behavior of gamma-Ni+gamma'-Ni3Al Alloys and Coatings Modified with Pt and Reactive Elements

    Energy Technology Data Exchange (ETDEWEB)

    Mu, Nan [Iowa State Univ., Ames, IA (United States)

    2007-12-01

    Materials for high-pressure turbine blades must be able to operate in the high-temperature gases (above 1000 C) emerging from the combustion chamber. Accordingly, the development of nickel-based superalloys has been constantly motivated by the need to have improved engine efficiency, reliability and service lifetime under the harsh conditions imposed by the turbine environment. However, the melting point of nickel (1455 C) provides a natural ceiling for the temperature capability of nickel-based superalloys. Thus, surface-engineered turbine components with modified diffusion coatings and overlay coatings are used. Theses coatings are capable of forming a compact and adherent oxide scale, which greatly impedes the further transport of reactants between the high-temperature gases and the underlying metal and thus reducing attack by the atmosphere. Typically, these coatings contain β-NiAl as a principal constituent phase in order to have sufficient aluminum content to form an Al2O3 scale at elevated temperatures. The drawbacks to the currently-used {beta}-based coatings, such as phase instabilities, associated stresses induced by such phase instabilities, and extensive coating/substrate interdiffusion, are major motivations in this study to seek next-generation coatings. The high-temperature oxidation resistance of novel Pt + Hf-modified γ-Ni + γ-Ni3Al-based alloys and coatings were investigated in this study. Both early-stage and 4-days isothermal oxidation behavior of single-phase γ-Ni and γ'-Ni3Al alloys were assessed by examining the weight changes, oxide-scale structures, and elemental concentration profiles through the scales and subsurface alloy regions. It was found that Pt promotes Al2O3 formation by suppressing the NiO growth on both γ-Ni and γ'Ni3Al single-phase alloys. This effect increases with increasing Pt content. Moreover, Pt exhibits this effect even at

  3. 3D Finite Element Modelling of Drilling Process of Al2024-T3 Alloy with solid tooling and Experimental Validation

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Tosello, Guido

    2017-01-01

    Drilling is an indispensable process for many manufacturing industries due to the importance of the process for assembling components. This study presents a 3D finite element modeling (3D FEM) approach for drilling process of aluminum 2024-T3. The 3D model of tool for two facet HSSCo and four facet...... area were determined numerically. The results confirm the ability and advantage of 3D FE model of the drilling process....... HSS were generated base on the details geometry. The simulations were carried out for both drills in different cutting conditions. The numerically obtained thrust forces were compared against experimental results. The tool stress distribution, chip formation and temperature distribution in the chip...

  4. Orientation-dependent crystal instability of gamma-TiAl in nanoindentation investigated by a multiscale interatomic potential finite-element model

    International Nuclear Information System (INIS)

    Xiong, Kai; Liu, Xiaohui; Gu, Jianfeng

    2014-01-01

    The anisotropic mechanical behavior of γ-TiAl alloys has been observed and repeatedly reported, but the effect of crystallographic orientations on the crystal instability of γ-TiAl is still unclear. In this paper, the orientation-dependent crystal instability of γ-TiAl single crystals was investigated by performing nanoindentation on different crystal surfaces. All the nanoindentations are simulated using an interatomic potential finite-element model (IPFEM). Simulation results show that the load–displacement curves, critical indentation depth and critical load for crystal instability as well as indentation modulus, are all associated with surface orientations. The active slip systems and the location of crystal instability in five typical nanoindentations are analyzed in detail, i.e. the (0 0 1), (1 0 0), (1 0 1), (1 1 0) and (1 1 1) crystal surfaces. The predicted crystal instability sites and the activated slipping systems in the IPFEM simulations are in good agreement with the dislocation nucleation in molecular dynamics simulations. (paper)

  5. Effects of Al2O3 and/or CaO on properties of yttria stabilized zirconia electrolyte doped with multi-elements

    International Nuclear Information System (INIS)

    Lv Zhengang; Guo Ruisong; Yao Pei; Dai Fengying

    2007-01-01

    Yttria stabilized zirconia (YSZ) has a high oxide ion conductivity at high temperatures. Some rare earth elements (e.g., Yb, Sc, Dy) with similar cation radii to Zr 4+ can dissolve into ZrO 2 , increasing its vacancy concentration and crystal lattice distortion, and therefore enhancing its conductivity and lowering the activation energy. It is expected this material could be used as intermediate temperature electrolyte. In the present work, YSZ electrolyte materials doped by multi-elements (Sc 2 O 3 or Dy 2 O 3 and Yb 2 O 3 ) were prepared by high temperature solid-state method. The high temperature conductivity was improved obviously, reaching 0.18 S/cm at 1000 deg. C, but the density and mechanical properties of sintered materials were not sufficiently high. It is found that sinterability and mechanical properties could be improved by inclusion of a small amount of Al 2 O 3 and/or CaO into the multi-elements doped YSZ materials and our results proved it. The results showed density and bending strength of sintered bodies were enhanced by Al 2 O 3 addition by 4.6% and 30%, respectively, while the conductivity did not degrade remarkably. But the degradation in bending strength and conductivity resulting from the CaO addition happened due to the second phase formed at the grain boundary. XRD patterns showed that all samples had cubic fluorite structure and crystalline lattice parameter was increased. SEM photographs obviously revealed the grain growth for the samples with CaO inclusion

  6. Interaction between uranium oxide alloyed with Al2O3·SiO2 and pyrocarbon coating during irradiation of micro fuel elements

    International Nuclear Information System (INIS)

    Chernikov, A.S.; Khromov, Y.F.; Svistunov, D.E.; Chuiko, E.E.

    1989-01-01

    The thermodynamics of the interaction between uranium oxide and carbon was previously studied in the presence of Al 2 O 3 ·SiO 2 , SiC, and UC 1.86 ; in this case, the quantity of the reacting substances does not have any effect on the attainment of the equilibrium state. Based on the obtained results, it is interesting to study the characteristic features of the interaction between the alloyed UO x cores (kernels) with the PyC-coating under the conditions involving irradiation of the micro fuel elements with thermal neutrons and the formation of solid fission products. The data concerning the characteristics of a micro fuel element (the weight of the core, its composition, etc.) are useful for carrying out a quantitative evaluation of the additives required for fixing the alkali-earth fission products by obtaining stable compounds of aluminosilicates with Ba, Sr, Rb, and Cs at different levels of depletion (burnup) of the oxide fuel. An analysis of the interaction processes in such a complex system as the irradiated alloyed uranium oxide fuel located in a micro fuel element is carried out by comparing the chemical potential of oxygen (RT ln P O 2 ) for the competing constituents of the system

  7. Programación lineal aplicada al cálculo plástico elemental de estructuras lineales

    Directory of Open Access Journals (Sweden)

    Antón Corrales, J. M.

    1970-06-01

    Full Text Available A method is described for elementary calculations of linear structures, under non elastic conditions, and subjected to point loads. The method involves the use of Simplex programs, which are already available for any scientific computer. The result gives either a factor of safety for a structure that has already been designed, or else an optimum design for given conditions. The calculation is very short for one loading system, and less so, if several loading conditions are assumed. The method can be further improved, thus rendering its use even more simple.Expone este artículo un método para hacer los cálculos plásticos elementales de estructuras lineales con cargas puntuales por medio de programas Simplex, ya disponibles en cualquier ordenador científico, dando como resultado, sea un coeficiente de seguridad de una estructura ya dimensionada, sea una optimización de la misma. El cálculo es muy corto con un caso de cargas, y menos con varios casos de cargas. El método admite perfeccionamientos, que pueden hacer todavía más elemental su introducción en computador.

  8. Factors that Influence the Price of Al, Cd, Co, Cu, Fe, Ni, Pb, Rare Earth Elements, and Zn

    Science.gov (United States)

    Papp, John F.; Bray, E. Lee; Edelstein, Daniel L.; Fenton, Michael D.; Guberman, David E.; Hedrick, James B.; Jorgenson, John D.; Kuck, Peter H.; Shedd, Kim B.; Tolcin, Amy C.

    2008-01-01

    This report is based on a presentation delivered at The 12th International Battery Materials Recycling Seminar, March 17-20, 2008, Fort Lauderdale, Fla., about the factors that influence prices for aluminum, cadmium, cobalt, copper, iron, lead, nickel, rare earth elements, and zinc. These are a diverse group of metals that are of interest to the battery recycling industry. Because the U.S. Geological Survey (USGS) closely monitors, yet neither buys nor sells, metal commodities, it is an unbiased source of metal price information and analysis. The authors used information about these and other metals collected and published by the USGS (U.S. production, trade, stocks, and prices and world production) and internationally (consumption and stocks by country) from industry organizations, because metal markets are influenced by activities and events over the entire globe. Long-term prices in this report, represented by unit values, were adjusted to 1998 constant dollars to remove the effects of inflation. A previous USGS study in this subject area was 'Economic Drivers of Mineral Supply' by Lorie A. Wagner, Daniel E. Sullivan, and John L. Sznopek (USGS Open File Report 02-335). By seeking a common cause for common behavior of prices among the various metal commodities, the authors found that major factors that influence prices of metal commodities were international events such as wars and recessions, and national events such as the dissolution of the Soviet Union in 1991 and economic growth in China, which started its open door policy in the 1970s but did not have significant market impact until the 1990s. Metal commodity prices also responded to commodity-specific events such as tariff or usage changes or mine strikes. It is shown that the prices of aluminum, cadmium, copper, iron, lead, nickel, and zinc are at historic highs, that world stocks are at (or near) historic lows, and that China's consumption of these metals had increased substantially, making it the world

  9. Geochemical dispersion of Si, Al, Fe, Mn, Na, K, Cu and Zn elements in soils and their use for characterization areas geochemically homogeneous

    International Nuclear Information System (INIS)

    Silva, W.R.L. da.

    1982-01-01

    Variations in the chemical composition of soils are used to characterize sub-areas geochemically - homogenous. The application of this methodology in a tropical humid region of accentuated topography constitute the principal objective of the present research. Samples of red latosols (Horizon B) developed over granite, sandstone and basalt occurring in the Central Granite Region of the Serra dos Carajas, Para State, Brazil were analized for the elements Si, Al, Fe, Mn, Na, K, Cu e Zn, by atomic absorption spectrophotometry. Based on the criterion of similarity in the chemical composition (Cluster Analysis, Factor Analysis) the soils were separeted in to different groups. The geographical distribution of the different groups permit the establishment of a close relationship between the different parent lithologies and their corresponding soils. (author)

  10. Spectrographic determination of impurities in ammonium bifluoride. III. Study of the processes of vaporization, transport and excitation of the elements Al, B, Cu and Cr

    International Nuclear Information System (INIS)

    Alduan, F. A.; Roca, M.; Capdevila, C.

    1979-01-01

    The influences of the processes of vaporization, transport and excitation on the shape of the volatilization-excitation curves and on the values of the spectral-line intensities have been investigated in a method for the spectrographic determination of Al, B, Cu and Cr In ammonium bifluoride samples by direct current are excitation in Scribner type electrodes, with addition of different matrices (graphite, 63203, GeO 2 , MgO and Zn0). The reaction products in the electrode cavity have been identified by X-ray powder diffraction analysis and the percentages of vaporized and diffused element evaluated through analysis by total-burning spectrographic methods. In addition, the values of both the number of particles entering the discharge column and the transport efficiencies have been calculated. Thus, the origin of most observed differences has been explained. (Author) 11 refs

  11. Universal Elements in Saudi Novel: A Study of Al-Gosaibi’s “Freedom Apartment” and Alem’s “The Dove’s Necklace”

    Directory of Open Access Journals (Sweden)

    Ahmed Mohamed Aboud

    2015-01-01

    Full Text Available In spite of the short history of the Saudi fiction, compared with the genre of poetry and with the rise of novel in other Arab countries like Egypt, Lebanon and Iraqi, Saudi novelists start to occupy a remarkable part of the space of Arab narration. Although Saudi novelists face the challenge of a restrictive cultural milieu, they seek to go beyond the local and regional levels and maintain a real significant universal presence. This study is a critical reaction to an outstanding attitude that colors the reception of Saudi fictional works. In reading of Saudi narrative texts readers, critics and scholars obviously focus on the local and regional aspects, and consciously or unconsciously ignore the universal perspectives that characterize their thematic and technical concerns. The study, accordingly, explores the world of Saudi fiction, concentrating on the question of universality, a concern which has been and will remain a core issue of critical and scholarly controversy. With reference to selected works, the study is an attempt to shed light on the universal aspects in Saudi novel. The basic and core premise of the study, then, is that the production of some Saudi novelists is rich in universal elements.  The study concentrates on Gazi Al-Gosaibi (1940 – 2010 and Rajaa Alem  (1956 – present as writers representing the search for universality in Saudi novel. Al-Gosaibi’s Freedom Apartment (1994 and Alem’s The Doves’ Necklace (2010 are works rich in persistent universal narrative themes and images. The main objective of the study is to show how these two texts, like many others, incarnate and present both Saudi culture and universal human values. With reference to these two novels, the researchers seek to prove the reliability of the main premise of the study. Keywords: Challenge Saudi novel, Universal elements of novel, Human values, Culture, Comparative literature

  12. Effect of Sn and Sb element on the magnetism and functional properties of Ni–Mn–Al ferromagnetic shape memory alloys

    Energy Technology Data Exchange (ETDEWEB)

    Agarwal, Sandeep, E-mail: sandeepxag@yahoo.co.in [LCMP, Department of Condensed Matter Physics and Material Sciences, SN Bose National Centre for Basic Sciences, JD Block, Salt Lake, Kolkata 700098 (India); Mukhopadhyay, P.K. [LCMP, Department of Condensed Matter Physics and Material Sciences, SN Bose National Centre for Basic Sciences, JD Block, Salt Lake, Kolkata 700098 (India)

    2016-03-15

    We have replaced Al partially with Sb and Sn in Ni–Mn–Al systems and investigated its effect on magnetism, entropy change and magnetoresistance in the vicinity of martensitic transformation. Both the samples had identical lattice parameters and Mn contents, which are mostly responsible for magnetism in these systems, yet there were marked changes in magnetic and functional properties of these systems. It was found that the magnetization increased in Sb alloy, while entropy change and magnetoresistance decreased as compared to Sn alloy. These changes are attributed to the change in antiferromagnetic interaction as a result of variation in the Ni d–Mn d hybridization arising due to presence of different sp elements. - Highlights: • Sn and Sb system has same Mn and Ni content and lattice parameter. • Both systems has disparity in magnetism, entropy change and magnetoresistance. • Difference was due to change in the Ni 3d–Mn 3d hybridization. • Sb based alloys are more suitable for mechanical devices. • Sn based alloys are more suitable for magnetocaloric effect and magnetoresistance.

  13. Three dimensional (3D) microstructure-based finite element modeling of Al-SiC nanolaminates using focused ion beam (FIB) tomography

    Energy Technology Data Exchange (ETDEWEB)

    Mayer, Carl R. [Materials Science and Engineering, Arizona State University, Tempe, AZ 85287-6106 (United States); Molina-Aladareguia, Jon [IMDEA Materials Institute, c/Eric Kandel 2, Getafe, Madrid 28906 (Spain); Chawla, Nikhilesh, E-mail: nchawla@asu.edu [Materials Science and Engineering, Arizona State University, Tempe, AZ 85287-6106 (United States)

    2016-10-15

    Al-SiC nanolaminate composites show promise as high performance coating materials due to their combination of strength and toughness. Although a significant amount of modeling effort has been focused on materials with an idealized flat nanostructure, experimentally these materials exhibit complex undulating layer geometries. This work utilizes FIB tomography to characterize this nanostructure in 3D and finite element modeling to determine the effect that this complex structure has on the mechanical behavior of these materials. A sufficiently large volume was characterized such that a 1 × 2 μm micropillar could be generated from the dataset and compared directly to experimental results. The mechanical response from this nanostructure was then compared to pillar models using simplified structures with perfectly flat layers, layers with sinusoidal waviness, and layers with arc segment waviness. The arc segment based layer geometry showed the best agreement with the experimentally determined structure, indicating it would be the most appropriate geometry for future modeling efforts. - Highlights: •FIB tomography was used to determine the structure of an Al-SiC nanolaminate in 3D. •FEM was used to compare the deformation of the nanostructure to experimental results. •Idealized structures from literature were compared to the FIB determined structure. •Arc segment based structures approximated the FIB determined structure most closely.

  14. The role of Al, Ba, and Cd dopant elements in tailoring the properties of c-axis oriented ZnO thin films

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Dilawar [Department of Physics GC University, Lahore 54000 (Pakistan); Center for Advanced Studies in Physics, GC University Lahore, Lahore 54000 (Pakistan); Butt, M.Z., E-mail: mzakriabutt@gmail.com [Center for Advanced Studies in Physics, GC University Lahore, Lahore 54000 (Pakistan); Arif, Bilal [Department of Physics, Faculty of Arts and Sciences, Firat University, 23169 Elazig (Turkey); Al-Ghamdi, Ahmed A. [Department of Physics, Faculty of Sciences, King Abdul Aziz University, Jeddah (Saudi Arabia); Yakuphanoglu, Fahrettin [Department of Physics, Faculty of Arts and Sciences, Firat University, 23169 Elazig (Turkey); Department of Physics, Faculty of Sciences, King Abdul Aziz University, Jeddah (Saudi Arabia)

    2017-02-01

    Highly c-axis oriented un-doped ZnO and Al-, Ba-, and Cd-doped ZnO thin films were successfully deposited on glass substrate employing sol-gel spin coating method. XRD analysis showed that all thin films possess hexagonal wurtzite structure with preferred orientation along c-axis. Field emission scanning electron microscope (FESEM) was used to study the morphology of thin films. The morphology consists of spherical and non-spherical shape grains. EDX analysis confirms the presence of O, Zn, Al, Ba, and Cd in the relevant thin films. The optical properties of thin films were studied using UV–Vis spectrometer. All thin films possess more than 85% optical transmittance in the visible region. Blue shift in optical band gap E{sub g} has been observed on doping with Al, whereas doping with Ba and Cd resulted in red shift of E{sub g}. Urbach energy E{sub u} of all doped ZnO thin films was found to have excellent correlation with their band gap energy E{sub g}. Moreover, E{sub g} increases while E{sub u} decreases on the increase in crystallite size D. Optical parameters E{sub g} and E{sub u} as well as structural parameters lattice strain and stacking fault probability also show excellent correlation with the B-factor or the mean-square amplitude of atomic vibrations of the dopant elements. Electrical conductivity measurement of the thin films was carried out using two-point probe method. The electrical conductivity was found to increase with the increase in crystallite orientation along c-axis.

  15. Estrategia de Aprendizaje Basado en Problemas (ABP) para explorar las concepciones alternativas relacionadas al tema estados de agregacion de la materia en estudiantes de nivel elemental =

    Science.gov (United States)

    Rosado Olivieri, Wilda Y.

    Gran parte de la investigacion acerca de la ensenanza de las ciencias se dedica a estudiar la forma o manera en que los estudiantes visualizan los conceptos cientificos. Para Driver (1983) esas ideas o concepciones se conocen como concepciones alternativas; las cuales pueden ocasionar dificultad para comprender los conceptos de las diferentes areas del conocimiento. El proposito de este estudio fue: (a) indagar como las distintas etapas del ABP permiten explorar las concepciones alternativas que poseen los estudiantes de nivel elemental acerca de los estados de agregacion de la materia y, (b) explorar en que medida el ABP permite identificar e incorporar las concepciones alternativas que poseen los estudiantes de nivel elemental con relacion al concepto de estados de agregacion de la materia para facilitar su aprendizaje. Con el fin de explorar las concepciones alternativas en el tema de los estados agregados de la materia se implanto la estrategia de Aprendizaje Basado en Problemas (ABP) con estudiantes de quinto grado de nivel elemental. Se utilizo la metodologia mixta con varias estrategias de recopilacion de datos, como una pre y pos prueba para elucidar el conocimiento previo y al mismo tiempo las concepciones alternativas sobre el tema bajo estudio y luego verificar el aprendizaje en los estudiantes. Asimismo, el uso de mapas conceptuales para determinar la profundidad del tema estudiado y el entrelazamiento de los conceptos Una tercera estrategia fue el grupo focal para tomar en cuenta la impresion de los estudiantes acerca del proyecto ABP. El aspecto colaborativo y cooperativo fue un factor fundamental, ya que el aprendizaje ocurrio en ese contexto educativo. Para los hallazgos de esta investigacion fue tan importante el conocimiento previo como los procesos que se generaban para que la adquisicion del mismo fuera de forma significativa y funcional (Escribano & Del Valle, 2010). La estrategia de ABP constituyo en este estudio una forma para indagar las

  16. Effects of alloying elements on the Snoek-type relaxation in Ti–Nb–X–O alloys (X = Al, Sn, Cr, and Mn)

    International Nuclear Information System (INIS)

    Lu, H.; Li, C.X.; Yin, F.X.; Fang, Q.F.; Umezawa, O.

    2012-01-01

    Highlights: ► The O Snoek-type relaxation in the Ti–Nb–X–O alloys was investigated. ► The dipole shape factor (δλ) and critical temperature T c were deduced from the peak. ► The δλ and T c were analyzed in terms of the d-orbital energy level (Md). ► With decreasing Md, the δλ increases and saturates at last while the T c decreases. ► The Md can be taken as a key parameter in designing high damping β-Ti alloys. - Abstract: The effect of alloying elements on the oxygen Snoek-type relaxation in the Ti–24Nb–X–1.7O alloys (X = 1Al, 2Al, 1Sn, 2Sn, 2Cr, 2Mn) was investigated in order to develop high damping materials based on point defect relaxation process. The relaxation strength of the Ti–Nb–Al–O and Ti–Nb–Sn–O alloys is the highest while that of the Ti–Nb–Mn–O and Ti–Nb–Cr–O alloys is the lowest. The dipole shape factor (δλ) and critical temperature T c , which are intrinsic to the Snoek-type relaxation, were figured out and analyzed in terms of the d-orbital energy level (Md) for each alloy based on the measured damping peak. With the decreasing Md, the δλ increases and saturates at last when the Md decreases to a certain value (about 2.435 eV), while the critical temperature T c decreases linearly. The parameter Md can be taken as a key parameter in designing high damping β-Ti alloys, that is, to design an intermediate value of Md at which the values of both δλ and T c are as high as possible.

  17. Effects of build orientation and element partitioning on microstructure and mechanical properties of biomedical Ti-6Al-4V alloy produced by laser sintering.

    Science.gov (United States)

    Mengucci, P; Gatto, A; Bassoli, E; Denti, L; Fiori, F; Girardin, E; Bastianoni, P; Rutkowski, B; Czyrska-Filemonowicz, A; Barucca, G

    2017-07-01

    Direct Metal Laser Sintering (DMLS) technology was used to produce tensile and flexural samples based on the Ti-6Al-4V biomedical composition. Tensile samples were produced in three different orientations in order to investigate the effect of building direction on the mechanical behavior. On the other hand, flexural samples were submitted to thermal treatments to simulate the firing cycle commonly used to veneer metallic devices with ceramics in dental applications. Roughness and hardness measurements as well as tensile and flexural mechanical tests were performed to study the mechanical response of the alloy while X-ray diffraction (XRD), electron microscopy (SEM, TEM, STEM) techniques and microanalysis (EDX) were used to investigate sample microstructure. Results evidenced a difference in the mechanical response of tensile samples built in orthogonal directions. In terms of microstructure, samples not submitted to the firing cycle show a single phase acicular α' (hcp) structure typical of metal parts subject to high cooling rates. After the firing cycle, samples show a reduction of hardness and strength due to the formation of laths of the β (bcc) phase at the boundaries of the primary formed α' plates as well as to lattice parameters variation of the hcp phase. Element partitioning during the firing cycle gives rise to high concentration of V atoms (up to 20wt%) at the plate boundaries where the β phase preferentially forms. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Binding energy, phonon spectra and thermodynamic properties of elements with type structures A1 (Al, Cu), A2 (V, Ti2), A3 (Mg, Tiβ), A4 (Si, Sn)

    International Nuclear Information System (INIS)

    Sirota, N.N.; Soshnina, T.M.; Sirota, I.M.; Sokolovskij, T.D.

    2001-01-01

    One calculated dependences of binding energy on spacing between the nearest atoms of Al and Cu elements with A 1 type structure, of V and Ti α elements with A 2 type structure, of Mg and Ti β elements with A 3 type structure, Si and Sn elements with A 4 type structure. To calculate one applied the methods based on the Thomas-Fermi statistic theory of atom. The derived dependences were approximated using the expression in the form of the Mie-Grueneisen potential. On the basis of the Born-von-Karman model of solid body one calculated the phonon spectra using which one determined temperature dependences of specific heat, free and internal energy of the investigated elements. The calculated values of energy of atomization, equilibrium closest interatomic spacing and temperature dependences of specific heat are in compliance with the experimental data [ru

  19. Study of deuterons induced nuclear reactions on light elements (N, Al and Si): Application to containment materials of radioactive wastes; Etude des reactions nucleaires induites par des deuterons sur des elements legers (N, Al, Si): application aux materiaux de confinement des dechets radioactifs

    Energy Technology Data Exchange (ETDEWEB)

    Pellegrino, St

    2004-03-01

    Nuclear reaction analysis is well adapted to the quantification of light element. Profiles of concentration in order to follow elements migration into materials can be undertaken. This technique is used to study the behavior of the future matrices for nuclear waste containment. This technique is isotopic, characterized by a good signal-to-background ratio and a very low detection limit. The probability of a nuclear reaction is linked to a parameter called 'cross section' we have to know in order to carry out quantitative analysis. We have determined excitation curves for nitrogen, aluminium and silicon. These experiments were done with deuterons from 0.5 to 2 MeV. Two methods for the cross section characterization are presented and are in agreement with each other. The second one reduces uncertainty. Data are incorporated in the simulation software SIMNRA. We have compared the results obtained on different samples when we use data in literature or data of the study. We have noticed a great fit improvement with the data of this study. The new cross sections of this work will be integrated in the general data base SIGMABASE. Applications on materials such as Si{sub 3}N{sub 4}, nano-metric powders, WCN and nuclear glass YLaMgSiAlON studied for radioactive waste containment are also presented. (author)

  20. Application of a powder sintering-extrusion process to the fabrication of U-Al and UO{sub 2}-stainless steel dispersed fuel elements; Application de frittage-filage de poudres a la fabrication d'elements combustibles disperses U-Al et UO{sub 2} inox

    Energy Technology Data Exchange (ETDEWEB)

    Meny, L.; Buffet, J.; Sauve, Ch.

    1962-07-01

    Within the scope of an investigation of dispersion-type fuel elements, the fabrication by extrusion and sintering of cladded bars and tubes with core of either uranium-aluminum or uranium oxide-stainless steel fuel was investigated. The powder mixtures are first pre-densified in a 'pot', whereupon the sheathed compact is degassed and sealed in a vacuum by electron-beam welding. The subsequent co-extrusion is performed at low temperature and with slow pressure application in the case of U-Al dispersions; and at high temperature with rapid pressure application, using the Ugine-Sejournet process, in the case of UO{sub 2}-stainless steel dispersions. The procedure permits the production of practically fully dense bars and tubes more than 1 m. in length and 10-30 mm in diameter, the wall thickness of the tubes ranging from 2-5 mm. The physical and mechanical characteristics of the dispersion, as well as the mechanical characteristics of the cladded elements, were investigated as a function of the uranium content and the temperature. (authors) [French] Dans le cadre de l'etude des elements combustibles disperses, nous avons etudie la fabrication par frittage-filage de barreaux et de tubes gaines renfermant un noyau combustible soit en uranium-aluminium, soit en UO{sub 2}-inox. Les melanges de poudres sont comprimes dans un 'pot'. La billette composite ainsi obtenue est degazee, fermee et soudee sous vide par bombardement electronique. Le cofilage est ensuite effectue, a basse temperature et sur presse lente pour les disperses U-Al, a haute temperature et sur presse rapide par le procede Ugine-Sejournet pour les disperses UO{sub 2}-inox. Nous avons ainsi obtenu des barres et des tubes de porosite pratiquement nulle de plus de 1 metre de longueur et de 10 a 30 mm de diametre; les epaisseurs des tubes sont comprises entre 2 et 5 mm. Les proprietes physiques et mecaniques des disperses ainsi que les proprietes mecaniques des ensembles gaines, ont ete etudiees en fonction de

  1. An Overview of the Effects of Alloying Elements on the Properties of Lightweight Fe-(15-35) Mn-(5-12) Al-(0.3-1.2) C Steel

    Science.gov (United States)

    Xing, Jia; Wei, Yinghui; Hou, Lifeng

    2018-04-01

    In this review, the influences of alloying elements on the phase constitution, density, and stacking fault energy of Fe-(15-35) Mn-(5-12) Al-(0.3-1.2) C lightweight steel are discussed. The mechanical properties of austenite single-phase and austenite-ferrite dual-phase Fe-Mn-Al-C steels processed by different procedures are also statistically analyzed. The austenite single-phase steel was found to possess superior strength and plasticity. Three reasonable explanations for the mechanism of plastic deformation are presented, namely, shear band-induced plasticity, microband-induced plasticity, and slip band refinement-induced plasticity.

  2. REAuAl{sub 4}Ge{sub 2} and REAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (RE=rare earth element): Quaternary intermetallics grown in liquid aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Xiuni, Wu [Department of Chemistry, Michigan State University, East Lansing, Michigan 48824 (United States); Kanatzidis, Mercouri G [Department of Chemistry, Michigan State University, East Lansing, Michigan 48824 (United States)

    2005-11-15

    The two families of intermetallic phases REAuAl{sub 4}Ge{sub 2} (1) (RE=Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Er, Tm and Yb) and REAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (2) (x=0.4) (RE=Ce and Eu) were obtained by the reactive combination of RE, Au and Ge in liquid aluminum. The structure of (1) adopts the space group R-3m (CeAuAl{sub 4}Ge{sub 2}, a=4.2384(7)A, c=31.613(7)A; NdAuAl{sub 4}Ge{sub 2}, a=4.2258(4)A, c=31.359(5)A; GdAuAl{sub 4}Ge{sub 2}, a=4.2123(6)A, c=30.994(6)A; ErAuAl{sub 4}Ge{sub 2}, a=4.2074(4)A, c=30.717(5)A). The structure of (2) adopts the tetragonal space group P4/mmm with lattice parameters: a=4.3134(8)A, c=8.371(3)A for EuAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4). Both structure types present slabs of ''AuAl{sub 4}Ge{sub 2}'' or ''AuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2}'' stacking along the c-axis with layers of RE atoms in between. Magnetic susceptibility measurements indicate that the RE atoms (except for Ce and Eu) possess magnetic moments consistent with +3 species. The Ce atoms in CeAuAl{sub 4}Ge{sub 2} and CeAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4) appear to be in a mixed +3/+4 valence state; DyAuAl{sub 4}Ge{sub 2} undergoes an antiferromagnetic transition at 11K and below this temperature exhibits metamagnetic behavior. The Eu atoms in EuAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4) appear to be in a 2+ oxidation state.

  3. Understanding corrosion via corrosion product characterization: II. Role of alloying elements in improving the corrosion resistance of Zn-Al-Mg coatings on steel

    International Nuclear Information System (INIS)

    Volovitch, P.; Vu, T.N.; Allely, C.; Abdel Aal, A.; Ogle, K.

    2011-01-01

    Highlights: → Origins of better corrosion resistance of ZnAlMg coatings than galvanized steel. → Comparative study of corrosion products formed on ZnAlMg, ZnMg and Zn coatings. → Modeling of dissolution and precipitation stages of corrosion. → At early stages Mg stabilizes protective zinc basic salts during dry-wet cycling. → At later stages Al dissolves at high pH forming protective layered double hydroxides. - Abstract: Corrosion products are identified on Zn, ZnMg and ZnAlMg coatings in cyclic corrosion tests with NaCl or Na 2 SO 4 containing atmospheres. For Mg-containing alloys the improved corrosion resistance is achieved by stabilization of protective simonkolleite and zinc hydroxysulfate. At later stages, the formation of layered double hydroxides (LDH) is observed for ZnAlMg. According to thermodynamic modeling, Mg 2+ ions bind the excess of carbonate or sulfate anions preventing the formation of soluble or less-protective products. A preferential dissolution of Zn and Mg at initial stages of corrosion is confirmed by in situ dissolution measurement. The physicochemical properties of different corrosion products are compared.

  4. Monitoring of Al3+-induced changes in growth, 14Co2 fixation of maize seedlings and some elements estimation by spectroscopic method

    International Nuclear Information System (INIS)

    Mostafa, I.Y.; Kamel, H.A.; Abd-ElAal, M.S.

    2004-01-01

    This experiment was carried out to study the effect of aluminum on the corn seedlings. Corn grains were divided to 9 groups. In the 1 st , 2 nd , 3 rd and 4 th groups, corn grains were soaked in 0.1, 1, 10 and 100 mM of Al solutions, respectively for 6 hours and sown in 15-cm pots. In the 5 th , 6 th . 7 th and 8 th groups, corn grains were sown in pots containing soil treated with 0.1, 1, 10 and 100 mM of Al solutions, respectively. The 9 th group used as control (neither grains nor soil treated with Al). After 10 days from cultivation lengths and weights of the seedlings, chlorophyll 'a' and 'b contents', 14 Co 2 fixation and some mineral ions were measured. The lower concentration 0.1 mM the soil treatments caused a significant increase in the shoot length/plant and insignificant increase in the root length when compared with the control, while all other concentrations in the two treatments caused a significant decrease in both the shoot and lengths. Shoot and fresh and dry weights/plant were significantly reduced by the different AI 3+ concentrations in both treatments except 0.1 mM of soil treatment. The ratio of dry weight/fresh weight of root was only increased in case of soil treatments. Chlorophyll 'a' and b content significantly increased by 0.1 mM Al in case of soaking and by 0.1 and 1 mM in case of soil treatments. 14 Co 2 fixation was significantly reduced due to soaking treatments, while it significantly increased by 0.1 mM Al 3+ - in case of soil treatments. Determination of Al, Fe, Mn, Ca, Mg, K and Na was carried out by flame atomic absorption spectrometry (F-AAS) with a good analytical speed out without noticeable interference

  5. Educaţia muzicală ca element definitoriu al formării spiritual-artistice în pedagogia Waldorf / Musical education as a defining element of artistic spiritual education in Waldorf's pedagogy

    OpenAIRE

    Surdu, Violeta; Gagim, Ion

    2017-01-01

    Abstract: Musical education consists a defining element of artistic spiritual education in Waldorf’s pedagogy. There is a spiritual sciece about the man in the centre of education’s process througn muzic that was founded by Rudolf Steiner. The process of the facilitations are centred according the necessity as a result of forming the musical culture of the pupils as a component part to their spiritual culture.

  6. Tunable optical properties of some rare earth elements-doped mayenite Ca12Al14O33 nanopowders elaborated by oxalate precursor route

    Science.gov (United States)

    Rashad, Mohamed M.; Mostafa, Ahmed G.; Mwakikunga, Bonex W.; Rayan, Diaa A.

    2017-01-01

    Rare earth (RE) ions-doped mayenite Ca12Al14- x RE x O33 nanopowders (where RE = La and Gd and x = 0-1.0) were synthesized using the oxalate precursor technique. The as-prepared precursors were calcined at 800 °C for 2 h. Obviously, all RE-doped Ca12Al14- x RE x O33 possessed a well-crystalline cubic mayenite phase till RE content of 0.8. The crystallo-chemical aspects including crystallite size, lattice parameters, theoretical X-ray density and bulk density were robustly on RE nature and ratio. The microstructure and the average grain size were significantly influenced by the RE kind and content. The high transparency of Ca12Al14- x RE x O33 over 80% was found to be evinced in the visible wavelength range of 400-800 nm. Besides, the incorporation of RE cation minimized the direct band gap energy from 4.42 eV for pure mayenite to 3.85 and 3.59 eV with x value 1.0 of La3+ and Gd3+ ions. The photoluminescence spectra of pure mayenite nanoparticles showed that the band edge emission ( λ exc = 248 nm) with an intense visible emission band at 360 nm was detected. Otherwise, the band edge emission showed a slight shift toward short wavelength due to the substitution Al3+ by RE3+ ions. Such results open a new avenue for application of mayenite as a good candidate for transparent low-temperature electron conductor for optoelectronics applications.

  7. A finite element analysis of the morphology of the twinned-to-detwinned interface observed in microstructure of the Cu-Al-Ni shape memory alloy

    Czech Academy of Sciences Publication Activity Database

    Seiner, Hanuš; Glatz, O.; Landa, Michal

    2011-01-01

    Roč. 48, č. 13 (2011), s. 2005-2014 ISSN 0020-7683 R&D Projects: GA ČR(CZ) GP202/09/P164; GA MŠk(CZ) 1M06031 Institutional research plan: CEZ:AV0Z20760514 Keywords : shape- memory alloys * finite element method * microstructure * energy minimization Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.857, year: 2011 http://www.sciencedirect.com/science/article/pii/S002076831100103X

  8. Effect of impurity elements Al, Mn, and N2 on the corrosion resistance of zircaloy-2 in high temperature water and steam

    International Nuclear Information System (INIS)

    Gadiyar, H.S.

    1978-01-01

    Although the impurity limits are specified in standard zircaloy-2, it is possible that during its manufacture some of the impurities may exceed by a few ppm than the normally set values. It is necessary to understand the corrosion behaviour of such zircaloy-2 which contain a small amount of excessive impurities. This report summarizes some such data of the impurities aluminium, manganese and nitrogen. It is seen that the common impurities which can affect the corrosion of zircaloy-2 significantly are Al and N 2 and to a lesser extent Mn. (author)

  9. Element-specific observation of the ferromagnetic ordering process in UCoAl via soft x-ray magnetic circular dichroism

    Science.gov (United States)

    Takeda, Yukiharu; Saitoh, Yuji; Okane, Tetsuo; Yamagami, Hiroshi; Matsuda, Tatsuma D.; Yamamoto, Etsuji; Haga, Yoshinori; Ōnuki, Yoshichika

    2018-05-01

    We have performed soft x-ray magnetic circular dichroism (XMCD) experiments on the itinerant-electron metamagnet UCoAl at the U 4 d -5 f (N4 ,5) and Co 2 p -3 d (L2 ,3) absorption edges in order to investigate the magnetic properties of the U 5 f and Co 3 d electrons separately. From the line shape of the XMCD spectrum, it is deduced that the orbital magnetic moment of the Co 3 d electrons is unusually large. Through the systematic temperature (T )- and magnetic field (H )-dependent XMCD measurements, we have obtained two types of the magnetization curve as a function of H and T (M-H curve and M-T curve, respectively). The metamagnetic transition from a paramagnetic state to a field-induced ferromagnetic state was clearly observed under 15 K at HM. The value of the HM and its T dependence agree well between the U and Co sites, and the bulk magnetization. Whereas, we have discovered the remarkable differences in the M-H and M-T curves between the U and Co sites. The present findings clearly show that the role of the Co 3 d electrons should be considered more carefully in order to understand the origin of the magnetic ordering in UCoAl.

  10. Microstructural Evolution during Pressureless Sintering of Blended Elemental Ti-Al-V-Fe Titanium Alloys from Fine Hydrogenated-Dehydrogenated Titanium Powder

    Directory of Open Access Journals (Sweden)

    Changzhou Yu

    2017-07-01

    Full Text Available A comprehensive study was conducted on microstructural evolution of sintered Ti-Al-V-Fe titanium alloys utilizing very fine hydrogenation-dehydrogenation (HDH titanium powder with a median particle size of 8.84 μm. Both micropores (5–15 μm and macropores (50–200 μm were identified in sintered titanium alloys. Spherical micropores were observed in Ti-6Al-4V sintered with fine Ti at the lowest temperature of 1150 °C. The addition of iron can help reduce microporosity and improve microstructural and compositional homogenization. A theoretical calculation of evaporation based on the Miedema model and Langmuir equation indicates that the evaporation of aluminum could be responsible for the formation of the macropores. Although reasonable densification was achieved at low sintering temperatures (93–96% relative density the samples had poor mechanical properties due mainly to the presence of the macroporosity and the high inherent oxygen content in the as-received fine powders.

  11. MAX phase – Alumina composites via elemental and exchange reactions in the Ti{sub n+1}AC{sub n} systems (A=Al, Si, Ga, Ge, In and Sn)

    Energy Technology Data Exchange (ETDEWEB)

    Cuskelly, Dylan, E-mail: dylan.cuskelly@uon.edu.au; Richards, Erin; Kisi, Erich, E-mail: Erich.Kisi@newcastle.edu.au

    2016-05-15

    Extension of the aluminothermal exchange reaction synthesis of M{sub n+1}AX{sub n} phases to systems where the element ‘A’ is not the reducing agent was investigated in systems TiO{sub 2}–A–Al–C for A=Al, Si, Ga, Ge, In and Sn as well as Cr{sub 2}O{sub 3}–Ga–Al–C. MAX phase-Al{sub 2}O{sub 3} composites were made in all systems except those with A=Ga or In. The effectiveness of conversion to MAX phases was generally in the range 63–96% without optimisation of starting ratios. Optimisation in the Ti–Si–C system gave a MAX phase component with >98% Ti{sub 3}SiC{sub 2}. - Graphical abstract: A range of Ti{sub n+1}AX{sub n} phases with different A elements were synthesised directly from the M oxide via exchange reactions. The process has now been shown to be general in all the systems marked in green in the table. - Highlights: • Ti{sub n+1}AC{sub n} phases were produced via a single step exchange reaction. • 3 MAX phase systems were successful via this method for the first time. • Cr{sub 2}GeC was also able to be produced via an exchange reaction. • The interconversion reaction in MAX phases is more general than previously thought.

  12. Structure data of elements and intermetallic phases. SubVol. B. Sulfides, selenides, tellurides. Pt. 1. Ag-Al-Cd-S. Cu-Te-Yb

    Energy Technology Data Exchange (ETDEWEB)

    Hellwege, K H; Hellwege, A M [eds.; Eisenmann, B; Schaefer, H

    1986-01-01

    Volume III/14 'Structure data of elements and intermetallic phases' is a supplement to and extension of Volume III/6. Since the publication of III/6 in 1971 (considering original papers up to 1967), the amount of new information for these substances has increased rapidly. Therefore the data had to be divided into several parts. The first part, III/14b1, is presented herewith. In Volume III/6, simple sulfides, selenides and tellurides were treated together with the intermetallic phases. The data are compiled in the same way as in III/6: for each substance the space group, lattice constants, their dependence on temperature and pressure, and other information is listed in the tables. In several cases, mostly for solid solutions, diagrams are given which are added in a separate chapter. Original papers containing a complete structure analysis are referred to in the tables. (orig./GSCH).

  13. Towards the development of new phosphors with reduced content of rare earth elements: Structural and optical characterization of Ce:Tb: Al{sub 2}SiO{sub 5}

    Energy Technology Data Exchange (ETDEWEB)

    Chiriu, D.; Stagi, L.; Carbonaro, C.M.; Corpino, R. [Dipartimento di Fisica, Università degli Studi di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy); Casula, M.F. [Dipartimento di Scienze Chimiche e Geologiche and INSTM, Università di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy); Ricci, P.C., E-mail: carlo.ricci@dsf.unica.it [Dipartimento di Fisica, Università degli Studi di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy)

    2016-05-15

    Highlights: • A new promising inert matrix as host of luminescent ions is proposed. • Al2SiO5 matrix is free from Rare earths (critical raw materials). • Doping the matrix with Ce and Tb we obtain an efficient green emitter. • Cerium acts as sensitizer for Terbium emission. - Abstract: A new promising inert matrix as host of luminescent ions is proposed. Al2SiO5 samples, doped with rare earths (Ce, Tb single doped and co-doped) are proposed as good prospect for the development of new UV–vis converter with reduced content of rare earths elements. Structural characterization by Raman, XRD spectroscopy and TEM imaging reveals the sillimanite phase and nano sized dimension of the investigated powders. Optical characterization by steady time and time resolved emission spectroscopy for the single doped and co-doped samples allows to identify an efficient energy transfer from Ce to Tb ions under near UV excitation wavelength. The intense green emission observed in the Ce:Tb co-doped Al2SiO5 system suggests its potential application as efficient blue pumped green emitter phosphor to be exploited for white LED: to this purpose we tested the compound in combination with a red emitting doping ion recording for Ce:Tb:Cr:ASO system a correlated color temperature of 6720 K.

  14. New procedure of quantitative mapping of Ti and Al released from dental implant and Mg, Ca, Fe, Zn, Cu, Mn as physiological elements in oral mucosa by LA-ICP-MS.

    Science.gov (United States)

    Sajnóg, Adam; Hanć, Anetta; Koczorowski, Ryszard; Barałkiewicz, Danuta

    2017-12-01

    A new procedure for determination of elements derived from titanium implants and physiological elements in soft tissues by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) is presented. The analytical procedure was developed which involved preparation of in-house matrix matched solid standards with analyte addition based on certified reference material (CRM) MODAS-4 Cormorant Tissue. Addition of gelatin, serving as a binding agent, essentially improved physical properties of standards. Performance of the analytical method was assayed and validated by calculating parameters like precision, detection limits, trueness and recovery of analyte addition using additional CRM - ERM-BB184 Bovine Muscle. Analyte addition was additionally confirmed by microwave digestion of solid standards and analysis by solution nebulization ICP-MS. The detection limits are in range 1.8μgg -1 to 450μgg -1 for Mn and Ca respectively. The precision values range from 7.3% to 42% for Al and Zn respectively. The estimated recoveries of analyte addition line within scope of 83%-153% for Mn and Cu respectively. Oral mucosa samples taken from patients treated with titanium dental implants were examined using developed analytical method. Standards and tissue samples were cryocut into 30µm thin sections. LA-ICP-MS allowed to obtain two-dimensional maps of distribution of elements in tested samples which revealed high content of Ti and Al derived from implants. Photographs from optical microscope displayed numerous particles with µm size in oral mucosa samples which suggests that they are residues from implantation procedure. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Quantitative research on microscopic deformation behavior of Ti-6Al-4V two-phase titanium alloy based on finite element method

    Science.gov (United States)

    Peng, Yan; Chen, Guoxing; Sun, Jianliang; Shi, Baodong

    2018-04-01

    The microscopic deformation of Ti-6Al-4V titanium alloy shows great inhomogeneity due to its duplex-microstructure that consists of two phases. In order to study the deformation behaviors of the constituent phases, the 2D FE model based on the realistic microstructure is established by MSC.Marc nonlinear FE software, and the tensile simulation is carried out. The simulated global stress-strain response is confirmed by the tensile testing result. Then the strain and stress distribution in the constituent phases and their evolution with the increase of the global strain are analyzed. The results show that the strain and stress partitioning between the two phases are considerable, most of the strain is concentrated in soft primary α phase, while hard transformed β matrix undertakes most of the stress. Under the global strain of 0.05, the deformation bands in the direction of 45° to the stretch direction and the local stress in primary α phase near to the interface between the two phases are observed, and they become more significant when the global strain increases to 0.1. The strain and stress concentration factors of the two phases are obviously different at different macroscopic deformation stages, but they almost tend to be stable finally.

  16. A benchmark report on MVA Berlin, the key element of waste management in Berlin; MVA Berlin als Herzstueck der Berliner Entsorgung im Vergleich mit der Wettbewerbs-Benchmark

    Energy Technology Data Exchange (ETDEWEB)

    Kempin, T. [Berliner Stadtreinigungsbetrieb, Berlin (Germany)

    2004-07-01

    The MVA Ruhleben incinerator has state-of-the-art technology, volume-dependent prime costs of 100-130 EUR/t, an acceptance payment of 63.70 EUR/t, employees covered by collective agreement system, disposal capacities of 500,000 tpa of residues, ecological sustainability, and customer-friendliness. Its importance will increase in the future as more than half of the expected waste volume of 983,000 tpa will be processed from 2005. (orig.) [German] Die MVA Ruhleben gewaehrleistet derzeit den Stand der Technik, mengenabhaengige Selbstkosten zwischen 100 EUR/t und 130 EUR/t, ein Annahmeentgelt von 63,70 EUR/t, soziale tarifgebundene Arbeitsplaetze, Entsorgungssicherheit, derzeit fuer 500.000 Tonnen Abfall pro Jahr, oekologische Nachhaltigkeit, Kundenfreundlichkeit. Die MVA Ruhleben wird zukuenftig fuer die Abfallentsorgung in Berlin eine noch groessere Bedeutung haben. Mit etwa 520.000 t/a Abfallentsorgungskapazitaet wird sie mehr als die Haelfte des erwarteten ueberlassungspflichtigen Restabfallaufkommens von 983.000 t/a ab 2005 verarbeiten. (orig.)

  17. Determination of Specific Forces and Tool Deflections in Micro-milling of Ti-6Al-4V alloy using Finite Element Simulations and Analysis

    International Nuclear Information System (INIS)

    Farina, Simone; Ceretti, Elisabetta; Thepsonti, Thanongsak; Oezel, Tugrul

    2011-01-01

    Titanium alloys offer superb properties in strength, corrosion resistance and biocompatibility and are commonly utilized in medical devices and implants. Micro-end milling process is a direct and rapid fabrication method for manufacturing medical devices and implants in titanium alloys. Process performance and quality depend upon an understanding of the relationship between cutting parameters and forces and resultant tool deflections to avoid tool breakage. For this purpose, FE simulations of chip formation during micro-end milling of Ti-6Al-4V alloy with an ultra-fine grain solid carbide two-flute micro-end mill are investigated using DEFORM software.At first, specific forces in tangential and radial directions of cutting during micro-end milling for varying feed advance and rotational speeds have been determined using designed FE simulations for chip formation process. Later, these forces are applied to the micro-end mill geometry along the axial depth of cut in 3D analysis of ABAQUS. Consequently, 3D distributions for tool deflections and von Misses stress are determined. These analyses will yield in establishing integrated multi-physics process models for high performance micro-end milling and a leap-forward to process improvements.

  18. Microstructural and elasto-plastic material parameters identification by inverse finite elements method of Ti{sub (1−x)}Al{sub x}N (0 < x < 1) sputtered thin films from Berkovich nano-indentation experiments

    Energy Technology Data Exchange (ETDEWEB)

    Pac, M.-J.; Giljean, S. [LPMT, Département MMPF (EA CNRS 4365), Université de Haute Alsace, 61 rue Albert Camus, 68093 Mulhouse (France); Rousselot, C. [FEMTO-ST, Département MN2S (UMR CNRS 6174), Université de Franche-Comté, 4 place Tharradin, 25211 Montbéliard (France); Richard, F. [FEMTO-ST, Département DMA (UMR CNRS 6174), Université de Franche-Comté, 24 chemin de l' Epitaphe, 25000 Besançon (France); Delobelle, P., E-mail: patrick.delobelle@univ-fcomte.fr [FEMTO-ST, Département DMA (UMR CNRS 6174), Université de Franche-Comté, 24 chemin de l' Epitaphe, 25000 Besançon (France)

    2014-10-31

    The mechanical properties of Ti{sub (1−x)}Al{sub x}N (0 < x < 1) films of different thicknesses deposited by r.f. reactive magnetron sputtering on Si < 100 > and high speed steel substrates have been investigated. The as-deposited coatings have been characterized by X-ray diffraction, atomic force microscopy, four-probe electric resistivity method, mechanical deflection of cantilever beams and Berkovich nano-indentation tests associated with inverse finite elements analysis. The coatings with x < 0.58–0.59 present a cubic structure whereas for x > 0.7 a hexagonal structure is observed. Between these two compositions cubic and hexagonal structures coexist. The roughness depends on the film thickness and on the Al content and a minimum associated to a very fine microstructure is clearly observed in the two-phase coatings. The electric resistivity sharply increases as soon as the hcp structure appears (x ∼ 0.6). The mean residual stresses are compressive, except for the AlN coating, and present a minimum at the neighborhood of x ∼ 0.64 where a mixed structure is observed. The indentation modulus M{sub } and the Berkovich hardness H{sub B} greatly depend on the Al content and a progressive decreasing has been observed for 0.58 < x < 0.7. For the M{sub } evolution, a simple model taking into account the stiffness coefficients of TiN and AlN structures, the mean residual stress level and the variations of the lattice parameters in the two structure domains is proposed. Knowing the elastic properties of these films, inverse finite elements analysis of the indentation curves considering a simple isotropic linear elasto-plastic behavior allows, as a function of the composition, the yield stress σ{sub Y} and the linear hardening coefficient H{sub p}{sup ⁎} to be estimated. σ{sub Y} and H{sub p}{sup ⁎} are in the ranges 4.2 to 6.8 GPa and 60 to 400 GPa, respectively. The maximum value of H{sub p}{sup ⁎}/σ{sub Y} which characterizes the ability

  19. /Cu-Al System

    Science.gov (United States)

    Kish, Orel; Froumin, Natalya; Aizenshtein, Michael; Frage, Nachum

    2014-05-01

    Wettability and interfacial interaction of the Ta2O5/Cu-Al system were studied. Pure Cu does not wet the Ta2O5 substrate, and improved spreading is achieved when relatively a high fraction of the active element (~40 at.% Al) was added. The Al2O3 and AlTaO4 phases were observed at the Ta2O5/Cu-Al interface. A thermodynamic evaluation allowed us to suggest that the lack of wetting bellow 40 at.% Al is due to the presence of a native oxide, which covers the drop. The conditions of the native oxide decomposition and the formation of the volatile Al2O suboxide strongly depend on the vacuum level during sessile drop experiments and the composition of the Cu-Al alloy. In our case, Al contents greater than 40% provides thermodynamic conditions for the formation of Al2O (as a result of Al reaction with Al2O3) and the drop spreading. It was suggested that the final contact angle in the Ta2O5/Cu-Al system (50°) is determined by Ta adsorption on the newly formed alumina interlayer.

  20. ALS Association

    Science.gov (United States)

    ... toward a world without ALS! Walk to Defeat ALS® Walk to Defeat ALS® draws people of all ... We need your help. I Will Advocate National ALS Registry The National ALS Registry is a congressionally ...

  1. Familial ALS

    Science.gov (United States)

    Boylan, Kevin

    2015-01-01

    Synopsis Genes linked to ALS susceptibility are being identified at an increasing rate owing to advances in molecular genetic technology. Genetic mechanisms in ALS pathogenesis appear to exert major effects in ~10% of patients, but genetic factors at some level may be important components of disease risk in most ALS patients. Identification of gene variants associated with ALS has informed concepts of the pathogenesis of ALS, aided the identification of therapeutic targets, facilitated research to develop new ALS biomarkers, and supported the establishment of clinical diagnostic tests for ALS-linked genes. Translation of this knowledge to ALS therapy development is ongoing. PMID:26515623

  2. Effect of trace elements (ZnSO/sub 4/, MnSO/sub 4//sub /and Al/sub 2/(SO/sub 4/)/sub 3/) on soil Ph, Zinc and manganese concentrations in case of mature teat bushes

    International Nuclear Information System (INIS)

    Nosheen, M.; Riaz, A.K.

    2005-01-01

    A field experiment was conducted to study the effect of trace elements on growth and yield of mature tea bushes, at National Tea Research Inst., Shinkiari, Mansehra, Pakistan, during 2003. The treatments included control (no fertilizer), recommended dose of NPK (432:111:74 kg ha/sup -1/ alone and NPK in combination with either two doses of (5.5 and 11 kg ha/sup -1/) ZnSO/sub 4/ or (2.0 and 4.0 kg ha/sup -1/)MnSO/sub 4/ or (0.225 and 0.45 kg ha/sup -1/) Al/sub 2/(SO/sub 4/)/sub 3/ to soil and one dose of each (11 kg ha/sup -1/) ZnSO/sub 4/, (4.0 kg ha/sup -1) MnSO/sub 4/ and (0.45 kg ha/sup -1/) Al/sub 2/(SO/sub 4/)/sub 3/ applied as spray solution. Treatments including soil application of NPK alone and NPK + either ZnSO/sub 4/, MnSO/sub 4/ or Al/sub 2/(SO/sub 4/)/sub 3/ significantly (P < 0.001) increased tea yield (fresh weight of three leaves + bud), shoot height and tissue Zn and Mn concentrations with significant interactions (T x t) on tissue Zn and Mn levels. As compared to control the yield increased by 7.0,30,.37,42,37 and 34% with NPK alone, NPK + 5.5, + 11.0 ZnSO/sub 4/, + 2.0, + 4.0 MnSO/sub 4/, + 0.225, + 0.45 kg ha/sup -1/ Al/sub 2/(SO/sub 4/)/sub 3/, respectively during fist three months while the yield of six months plucking showed similar response to treatments but was significantly lower than the first three months. Soil pH, Zn and Mn concentrations were significantly affected by treatments, time of sampling, and depth of sampling. Except ZnSO/sub 4/, lower doses of MnSO/sub 4/ (2.0 kg ha-l) and Al/sub 2/(SO/sub 4/)/sub 3/ (0.225 kg ha/sup -1/), were more effective as compared to their higher doses when applied to soil, regarding tea yield and shoot height. Foliar application of 11 kg ha-l ZnSO/sub 4/ significantly increased yield as compared to its both levels when applied to soil. It is concluded that MnSO/sub 4/ and Al/sub 2/(SO/sub 4/)/sub 3/ should be applied at the rate of 2.0 and 0.225 kg ha/sup -l/. (author)

  3. Spectrographic determination of impurities in ammonium bifluoride. III. Study of the processes of vaporization, transport and excitation of the elements Al, B, Cu and Cr; Determinacion espectrografico de impurezas en bifluoruro amonico. III. Estudio de los procesos de volatilizacion, transporte y excitacion de los elementos Al, B, Cu, Cr

    Energy Technology Data Exchange (ETDEWEB)

    Alduan, F A; Roca, M; Capdevila, C

    1979-07-01

    The influences of the processes of vaporization, transport and excitation on the shape of the volatilization-excitation curves and on the values of the spectral-line intensities have been investigated in a method for the spectrographic determination of Al, B, Cu and Cr In ammonium bifluoride samples by direct current are excitation in Scribner type electrodes, with addition of different matrices (graphite, 63203, GeO{sub 2}, MgO and Zn0). The reaction products in the electrode cavity have been identified by X-ray powder diffraction analysis and the percentages of vaporized and diffused element evaluated through analysis by total-burning spectrographic methods. In addition, the values of both the number of particles entering the discharge column and the transport efficiencies have been calculated. Thus, the origin of most observed differences has been explained. (Author) 11 refs.

  4. Standard elements; Elements standards

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Following his own experience the author recalls the various advantages, especially in the laboratory, of having pre-fabricated vacuum-line components at his disposal. (author) [French] A la suite de sa propre experience, l'auteur veut rappeler les divers avantages que presente, tout particulierement en laboratoire, le fait d'avoir a sa disposition des elements pre-fabriques de canalisations a vide. (auteur)

  5. Galvanic element. Galvanisches Element

    Energy Technology Data Exchange (ETDEWEB)

    Sprengel, D.; Haelbig, H.

    1980-01-03

    The invention concerns a gas-tight sealed accumulator with positive and negative electrode plates and an auxillary electrode electroconductively bound to the latter for suppressing oxygen pressure. The auxillary electrode is an intermediate film electrode. The film catalysing oxygen reduction is hydrophilic in character and the other film is hydrophobic. A double coated foil has proved to be advantageous, the hydrophilic film being formed from polymer-bound activated carbon and the hydrophrobic film from porous polytetrafluoroethylene. A metallic network of silver or nickel is rolled into the outer side of the activated carbon film. This auxillary electrode can be used to advantage in all galvanic elements. Even primary cells fall within the scope of application for auxillary electrodes because many of these contain a highly oxidized electrodic material which tends to give off oxygen.

  6. Limitless Analytic Elements

    Science.gov (United States)

    Strack, O. D. L.

    2018-02-01

    We present equations for new limitless analytic line elements. These elements possess a virtually unlimited number of degrees of freedom. We apply these new limitless analytic elements to head-specified boundaries and to problems with inhomogeneities in hydraulic conductivity. Applications of these new analytic elements to practical problems involving head-specified boundaries require the solution of a very large number of equations. To make the new elements useful in practice, an efficient iterative scheme is required. We present an improved version of the scheme presented by Bandilla et al. (2007), based on the application of Cauchy integrals. The limitless analytic elements are useful when modeling strings of elements, rivers for example, where local conditions are difficult to model, e.g., when a well is close to a river. The solution of such problems is facilitated by increasing the order of the elements to obtain a good solution. This makes it unnecessary to resort to dividing the element in question into many smaller elements to obtain a satisfactory solution.

  7. Modeling and Finite Element Analysis for the Dynamic Recrystallization Behavior of Ti-5Al-5Mo-5V-3Cr-1Zr Near β Titanium Alloy During Hot Deformation

    Science.gov (United States)

    Lv, Ya-ping; Li, Shao-jun; Zhang, Xiao-yong; Li, Zhi-you; Zhou, Ke-chao

    2018-04-01

    Evolution for the dynamic recrystallization (DRX) volume fraction of Ti-5Al-5Mo-5V-3Cr-1Zr near β titanium alloy during hot deformation was characterized by using the Johnson-Mehl-Avrami-Kolmogorov (JMAK) equation. To determine the equation parameters, a series of thermal simulation experiments at the temperature of 1023-1098 K and strain rate of 0.001-1 s‒1 to the true strain of 0.7 were conducted to obtain the essential data about stress σ and strain ɛ. By further transforming the relationship of σ versus ɛ into the relationship of strain hardening rate dσ/dɛ versus σ, two characteristic strains at the beginning of DRX (critical strain ɛc) and at the peak stress (peak strain ɛp) were identified from the dσ/dɛ-σ curves. Sequentially, the parameters in the JMAK equation were determined from the linear fitting of the different relationships among critical strain ɛc, peak strain ɛp and deformation conditions (including temperature T, strain rate \\dot ɛ and strain ɛ). The as-obtained JMAK equation was expressed as XDRX=1-exp[-0.0053((ɛ-ɛc)/ɛc)2.1], where ɛc=0.6053ɛp and ɛp=0.0031 \\dot ɛ .0081exp(28,781/RT). Finally, the JMAK equation was implanted into finite element program to simulate the hot compression of thermal simulation experiments. The simulation predictions and experimental results about the DRX volume fraction distribution showed a good consistency.

  8. Newly developed active braze powders based on commercial nickel brazes using zirconium as active element for joining ceramic to metal; Entwicklung von neuen Aktivlotpulvern auf Basis kommerzieller Nickellote mit Zirkon als aktivelement zum Fuegen von Keramik-Metall-Verbunden

    Energy Technology Data Exchange (ETDEWEB)

    Bobzin, K.; Schlaefer, T.; Kopp, N.; Schlegel, A. [Institut fuer Oberflaechentechnik der RWTH Aachen (Germany)

    2010-06-15

    von 500 C zu entwickeln, die sich zudem beim Einsatz in kohlenwasserstoffhaltigen Umgebungen bestaendiger gegen korrosive Angriffe zeigen als Aktivlote auf Silber/Kupfer-, Kupfer-, und Silberbasis. Ausgehend von den Nickelbasisloten NI 102, NI 105 und NI 107 wurden Experimentallote mit Zirkon als grenzflaechenaktivem Element hergestellt. Die Modifizierung der Basislote erfolgte zum einen pulvermetallurgisch unter der Verwendung von Zirkonhydrid durch Mischen oder mechanisches Legieren mit einer Hochenergiekugelmuehle. Zum anderen wurden die Basislote schmelzmetallurgisch mit Zirkon legiert. Der Aktivmetallgehalt variierte zwischen 2 Gew.-% und 10 Gew.-%. Zur Charakterisierung diente die thermoanalytische Vermessung der Schmelzbereiche aller Experimentallote und die pulvermorphologische sowie roentgendiffraktometrische Analyse der pulvermetallurgisch hergestellten. Die Eignung der Experimentallote fuer das Aktivloeten wurde in Benetzungstests auf Aluminiumoxid in Hochvakuumloetversuchen experimentell untersucht und metallographisch bewertet.

  9. Ti, Al

    Indian Academy of Sciences (India)

    In the present study, authors report on the effect that substrate bias voltage has on the microstructure and mechanical properties of (Ti, Al)N hard coatings deposited with cathodic arc evaporation (CAE) technique. The coatings were deposited from a Ti0.5Al0.5 powder metallurgical target in a reactive nitrogen atmosphere at ...

  10. Transplutonium elements

    Energy Technology Data Exchange (ETDEWEB)

    Sivaramakrishnan, C. K.; Jadhav, A. V.; Reghuraman, K.; Mathew, K. A.; Nair, P. S.; Ramaniah, M. V.

    1973-07-01

    Research progress is reported on studies of the transplutonium elements including recovery and purification of americium, preparation of /sup 238/Pu, extraction studies using diethylhexyl phosphate. (DHM)

  11. The effect of H2O gas on volatilities of planet-forming major elements. I - Experimental determination of thermodynamic properties of Ca-, Al-, and Si-hydroxide gas molecules and its application to the solar nebula

    Science.gov (United States)

    Hashimoto, Akihiko

    1992-01-01

    The vapor pressures of Ca(OH)2(g), Al(OH)3(g), and Si(OH)4(g) molecules in equilibrium with solid calcium-, aluminum, and silicon-oxides, respectively, were determined, and were used to derive the heats of formation and entropies of these species, which are expected to be abundant under the currently postulated physical conditions in the primordial solar nebula. These data, in conjunction with thermodynamic data from literature, were used to calculate the relative abundances of M, MO(x), and M(OH)n gas species and relative volatilities of Fe, Mg, Si, Ca, and Al for ranges of temperature, total pressure, and H/O abundance ratio corresponding to the plausible ranges of physical conditions in the solar nebula. The results are used to explain how Ca and Al could have evaporated from Ca,Al-rich inclusions in carbonaceous chondrites, while Si, Mg, and Fe condensed onto them during the preaccretion alteration of CAIs.

  12. Intrinsic origin of interface states and band offset profiling of nanostructured LaAlO3/SrTiO3 heterojunctions probed by element-specific resonant spectroscopies

    NARCIS (Netherlands)

    Drera, G.; Salvinelli, G.; Bondino, F.; Magnano, E.; Huijben, Mark; Brinkman, Alexander; Sangaletti, L.

    2014-01-01

    The origin of electronic states at the basis of the 2DEG found in conducting LaAlO 3 /SrTiO 3 interfaces (5 u.c. LaAlO 3 ) is investigated by resonant photoemission experiments at the Ti L 2,3 and La M 4,5 edges. As shown by the resonant enhancement at the Ti L 2,3 edge, electronic states at E F

  13. Toxic Elements

    DEFF Research Database (Denmark)

    Hajeb, Parvaneh; Shakibazadeh, Shahram; Sloth, Jens Jørgen

    2016-01-01

    Food is considered the main source of toxic element (arsenic, cadmium, lead, and mercury) exposure to humans, and they can cause major public health effects. In this chapter, we discuss the most important sources for toxic element in food and the foodstuffs which are significant contributors to h...

  14. The effect of substitutional elements (Al, Co) in LaNi4.5M0.5 on the lattice defect formation in the initial hydrogenation and dehydrogenation

    International Nuclear Information System (INIS)

    Sakaki, Kouji; Akiba, Etsuo; Mizuno, Masataka; Araki, Hideki; Shirai, Yasuharu

    2009-01-01

    The formation of the vacancy and dislocation by the initial hydrogenation and dehydrogenation in LaNi 4.5 M 0.5 (M = Al, Co, and Ni) was observed by means of the positron lifetime technique. The concentrations of vacancy introduced by these processes were 0.25, 0.13 and 0.01 at.% for LaNi 5 , LaNi 4.5 Co 0.5 and LaNi 4.5 Al 0.5 , respectively. Al substitution into LaNi 5 significantly prevented from vacancy formation, compared with LaNi 5 and LaNi 4.5 Co 0.5 . In LaNi 4.5 Al 0.5 , the increase of the hardness and the enhancement of the pulverization, i.e. enhancement of the formation of micro cracks compared with LaNi 5 were observed while the Co substitution had little effect on pulverization and hardness as well as vacancy formation. These results show that the formation of micro cracks became more active process by Al substitution than the formation of the lattice defects to release the strain energy generated by the hydride formation because of the higher formation energy of the lattice defects in LaNi 4.5 Al 0.5 , although both the formation of micro cracks and lattice defects were still observed in all alloys we studied

  15. Fuel element

    International Nuclear Information System (INIS)

    Armijo, J.S.

    1976-01-01

    A fuel element for nuclear reactors is proposed which has a higher corrosion resisting quality in reactor operations. The zirconium alloy coating around the fuel element (uranium or plutonium compound) has on its inside a protection layer of metal which is metallurgically bound to the substance of the coating. As materials are namned: Alluminium, copper, niobium, stainless steel, and iron. This protective metallic layer has another inner layer, also metallurgically bound to its surface, which consists usually of a zirconium alloy. (UWI) [de

  16. Friction stir processing of an aluminum-magnesium alloy with pre-placing elemental titanium powder: In-situ formation of an Al{sub 3}Ti-reinforced nanocomposite and materials characterization

    Energy Technology Data Exchange (ETDEWEB)

    Khodabakhshi, F., E-mail: farzadkhodabakhshi83@gmail.com [Department of Materials Science and Engineering, School of Engineering, Shiraz University, Zand Boulevard, Shiraz (Iran, Islamic Republic of); Simchi, A. [Department of Materials Science and Engineering, Sharif University of Technology, P.O. Box 11365-9466, Azadi Avenue, 14588 Tehran (Iran, Islamic Republic of); Institute for Nanoscience and Nanotechnology, Sharif University of Technology, P.O. Box 11365-9466, Azadi Avenue, 14588 Tehran (Iran, Islamic Republic of); Kokabi, A.H. [Department of Materials Science and Engineering, Sharif University of Technology, P.O. Box 11365-9466, Azadi Avenue, 14588 Tehran (Iran, Islamic Republic of); Gerlich, A.P. [Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, ON (Canada)

    2015-10-15

    A fine-grained Al–Mg/Al{sub 3}Ti nanocomposite was fabricated by friction stir processing (FSP) of an aluminum-magnesium (AA5052) alloy with pre-placed titanium powder in the stirred zone. Microstructural evolutions and formation of intermetallic phases were analyzed by optical and electron microscopic techniques across the thickness section of the processed sheets. The microstructure of the nanocomposite consisted of a fine-grained aluminum matrix (1.5 µm), un-reacted titanium particles (<40 µm) and reinforcement particles of Al{sub 3}Ti (<100 nm) and Mg{sub 2}Si (<100 nm). Detailed microstructural analysis indicated solid-state interfacial reactions between the aluminum matrix and micro-sized titanium particles to form Al{sub 3}Ti intermetallic phase. The hard inclusions were then fractured and re-distributed in the metal matrix by the severe thermo-mechanical conditions imposed by FSP. Evaluation of mechanical properties by hardness measurement and uniaxial tensile test determined significant enhancement in the mechanical strength (by 2.5 order of magnetite) with a high ductility (~22%). Based on a dislocation-based model analysis, it was suggested that the strength enhancement was governed by grain refinement and the presence of hard inclusions (4 vol%) in the metal matrix. Fractographic studies also showed a ductile-brittle fracture mode for the nanocomposite compared with fully ductile rupture of the annealed alloy as well as the FSPed specimen without pre-placing titanium particles. - Highlights: • FSP was employed to fabricate in situ nanocomposite. • The AA5052 Al alloy with pre-placed micro-sized Ti particles were utilized. • The structural analysis was revealed that the in situ formation of Al{sub 3}Ti nanophase. • The SZ grain structure was refined by PSN and ZHP mechanisms during DRX. • Hardness and tensile strength were improved up to ~2.5 times with a good ductility.

  17. AL Amyloidosis

    Directory of Open Access Journals (Sweden)

    Desport Estelle

    2012-08-01

    Full Text Available Abstract Definition of the disease AL amyloidosis results from extra-cellular deposition of fibril-forming monoclonal immunoglobulin (Ig light chains (LC (most commonly of lambda isotype usually secreted by a small plasma cell clone. Most patients have evidence of isolated monoclonal gammopathy or smoldering myeloma, and the occurrence of AL amyloidosis in patients with symptomatic multiple myeloma or other B-cell lymphoproliferative disorders is unusual. The key event in the development of AL amyloidosis is the change in the secondary or tertiary structure of an abnormal monoclonal LC, which results in instable conformation. This conformational change is responsible for abnormal folding of the LC, rich in β leaves, which assemble into monomers that stack together to form amyloid fibrils. Epidemiology AL amyloidosis is the most common type of systemic amyloidois in developed countries with an estimated incidence of 9 cases/million inhabitant/year. The average age of diagnosed patients is 65 years and less than 10% of patients are under 50. Clinical description The clinical presentation is protean, because of the wide number of tissues or organs that may be affected. The most common presenting symptoms are asthenia and dyspnoea, which are poorly specific and may account for delayed diagnosis. Renal manifestations are the most frequent, affecting two thirds of patients at presentation. They are characterized by heavy proteinuria, with nephrotic syndrome and impaired renal function in half of the patients. Heart involvement, which is present at diagnosis in more than 50% of patients, leading to restrictive cardiopathy, is the most serious complication and engages prognosis. Diagnostic methods The diagnosis relies on pathological examination of an involved site showing Congo red-positive amyloid deposits, with typical apple-green birefringence under polarized light, that stain positive with an anti-LC antibody by immunohistochemistry and

  18. PELTIER ELEMENTS

    CERN Document Server

    Tani, Laurits

    2015-01-01

    To control Peltier elements, temperature controller was used. I used TEC-1091 that was manufactured my Meerstetter Engineering. To gain control with the temperature controller, software had to be intalled on a controlling PC. There were different modes to control the Peltier: Tempererature controller to control temperature, Static current/voltage to control voltage and current and LIVE ON/OFF to auto-tune the controller respectively to the system. Also, since near the collision pipe there is much radiation, radiation-proof Peltier elements have to be used. To gain the best results, I had to find the most efficient Peltier elements and try to get their cold side to -40 degrees Celsius.

  19. Fuel element

    International Nuclear Information System (INIS)

    Kennedy, S.T.

    1982-01-01

    A nuclear reactor fuel element wherein a stack of nuclear fuel is prevented from displacement within its sheath by a retainer comprising a tube member which is radially expanded into frictional contact with the sheath by means of a captive ball within a tapered bore. (author)

  20. Transactinide elements

    International Nuclear Information System (INIS)

    Hemingway, J.D.

    1975-01-01

    The review is covered in sections, entitled: predicted nuclear properties - including closed shells, decay characteristics; predicted chemical properties - including electronic structure and calculated properties, X-radiation, extrapolated chemical properties, separation chemistry; methods of synthesis; the natural occurrence of superheavy elements. (U.K.)

  1. K-shell x-ray production cross sections of selected elements Al to Ni for 4.0 to 38.0 MeV 10B ions

    International Nuclear Information System (INIS)

    Monigold, G.; McDaniel, F.D.; Duggan, J.L.; Mehta, R.; Rice, R.; Miller, P.D.

    1976-01-01

    K-Shell x-ray production cross sections for the target elements Sc, Ti, V, Mn, Fe, Co, and Ni were measured for incident 10 B ions over the energy range 4.0 to 38.0 MeV. The cross section data were compared to the theoretical predictions of the binary encounter approximation (BEA); the plane wave born approximation (PWBA); and the PWBA modified to include corrections for increased binding energy (B), Coulomb deflection of the incident ion (C), orbital perturbation due to polarization (P), and relativistic effects (R). In addition, fluorescence yield variations (W/sub K/) and contributions to the cross sections from electron capture (EC) were included. It was found that the predictions of the fully modified PWBA with contributions from electron capture and fluorescence yield variations included provided the best fit to the experimental data over the entire energy range for each target element. The Kβ/Kα x-ray intensity ratios were compared to theoretical values that assume single hole ionization, and the x-ray energy shifts presented as a function of the energy of the incident ion. These two measurements provided confirmation of the occurrence of multiple ionization for 10 B bombardment of target elements in the range 21 less than or equal to Z 2 less than or equal to 28

  2. Ucla, escuela elemental

    Directory of Open Access Journals (Sweden)

    Neutra, Richard J.

    1962-03-01

    Full Text Available La Escuela Elemental de Preparación de la Universidad de California, en Los Angeles, está dedicada a la educación e investigación y preparación del profesorado de la infancia. Se ha construido en un paraje maravilloso, de frondosa vegetación, frente a un terreno bastante quebrado, circunstancia que presta mayor encanto al conjunto, construido con gran pericia y adaptación al paisaje a base de una dominante horizontalidad, con materiales sencillos (ladrillos, hierro y madera y gran comunicación con la naturaleza mediante grandes cristaleras correderas que ensanchan las clases y las suplementan hacia el jardín de acuerdo con las nuevas normas y prácticas docentes.

  3. High Temperature AL-Nanocrystal Alloy Synthesis

    National Research Council Canada - National Science Library

    Perepezko, J

    2001-01-01

    Aluminum-rich metallic glasses containing transition metals and rare earth elements have been found to yield finely mixed microstructures of Al nanocrystals embedded in an amorphous matrix and exhibit...

  4. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Kawada, Toshiyuki; Hirayama, Satoshi; Yoneya, Katsutoshi.

    1980-01-01

    Purpose: To enable load-depending operation as well as moderation for the restriction of operation conditions in the present nuclear reactors, by specifying the essential ingredients and the total weight of the additives to UO 2 fuel substances. Constitution: Two or more additives selected from Al 2 O 3 , B 2 O, CaO, MgO, SiO 2 , Na 2 O and P 2 O 5 are added by the total weight of 2 - 5% to fuel substances consisting of UO 2 or a mixture of UO 2 and PuO 2 . When the mixture is sintered, the strength of the fuel elements is decreased and the fuel-cladding interactions due to the difference in the heat expansion coefficients between the ceramic fuel elements and the metal claddings are decreased to a substantially harmless degree. (Horiuchi, T.)

  5. New elements

    International Nuclear Information System (INIS)

    Flerov, G.

    1976-01-01

    The history is briefly described of the investigation of superheavy elements at the Joint Institute for Nuclear Research at Dubna. The significance of the investigation is assessed from the point of view of the nuclear structure study and major problems encountered in experimental efforts are indicated. Current experimental methods aiming at the discovery or the production of superheavy nuclei with Z approximately 114 are listed. (I.W.)

  6. Exploration of R2XM2 (R=Sc, Y, Ti, Zr, Hf, rare earth; X=main group element; M=transition metal, Si, Ge): Structural Motifs, the novel Compound Gd2AlGe2 and Analysis of the U3Si2 and Zr3Al2 Structure Types

    Energy Technology Data Exchange (ETDEWEB)

    McWhorter, Sean William [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    In the process of exploring and understanding the influence of crystal structure on the system of compounds with the composition Gd5(SixGe1-x)4 several new compounds were synthesized with different crystal structures, but similar structural features. In Gd5(SixGe1-x)4, the main feature of interest is the magnetocaloric effect (MCE), which allows the material to be useful in magnetic refrigeration applications. The MCE is based on the magnetic interactions of the Gd atoms in the crystal structure, which varies with x (the amount of Si in the compound). The crystal structure of Gd5(SixGe1-x)4 can be thought of as being formed from two 32434 nets of Gd atoms, with additional Gd atoms in the cubic voids and Si/Ge atoms in the trigonal prismatic voids. Attempts were made to substitute nonmagnetic atoms for magnetic Gd using In, Mg and Al. Gd2MgGe2 and Gd2InGe2 both possess the same 32434 nets of Gd atoms as Gd5(SixGe1-x)4, but these nets are connected differently, forming the Mo2FeB2 crystal structure. A search of the literature revealed that compounds with the composition R2XM2 (R=Sc, Y, Ti, Zr, Hf, rare earth; X=main group element; M=transition metal, Si, Ge) crystallize in one of four crystal structures: the Mo2FeB2, Zr3Al2, Mn2AlB2 and W2CoB2 crystal structures. These crystal structures are described, and the relationships between them are highlighted. Gd2AlGe2 forms an entirely new crystal structure, and the details of its synthesis and characterization are given. Electronic structure calculations are performed to understand the nature of bonding in this compound and how

  7. The effect of the addition of the elements Ni, Zn and Co in a composite AlTiO2 obtained by high-energy milling and sintering process

    International Nuclear Information System (INIS)

    Carvalho, C.O. de; Coelho, R.E.; Conrado, L.C.; Nascimento, C.S.; Teixeira, C.A.; Mendonca, E.S.

    2016-01-01

    The present work use aluminum scrap with addition of TiO 2 , Ni, Zn or Co to preparation and characterization of nanocomposites. The aluminum were cut and subjected to high energy milling for 2 hours at 1200rpm. The obtained powder was added to TiO 2 , Ni, Zn or Co in a nominal composition 97Al-2TiO 2 -1X (X = Ni, Zn or Co) (weight %) and again, the mixture was subjected to milling for 1 hour at 1000rpm. Grinding powders were hot pressed in the closed die and then removed; the compressed were sintered at 950°C in a tubular furnace N 2 passing atmosphere. The samples obtained were characterized by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD). The results of SEM images showed a very refined microstructure and an aluminum matrix without porosity. (author)

  8. Radiographic element

    International Nuclear Information System (INIS)

    Abbott, T.I.; Jones, C.G.

    1984-01-01

    Radiographic elements are disclosed comprised of first and second silver halide emulsion layers separated by an interposed support capable of transmitting radiation to which the second image portion is responsive. At least the first imaging portion contains a silver halide emulsion in which thin tubular silver halide grains of intermediate aspect ratios (from 5:1 to 8:1) are present. Spectral sensitizing dye is adsorbed to the surface of the tubular grains. Increased photographic speeds can be realized at comparable levels of crossover. (author)

  9. Superheavy elements

    CERN Document Server

    Hofmann, S

    1999-01-01

    The outstanding aim of experimental investigations of heavy nuclei is the exploration of spherical 'SuperHeavy Elements' (SHEs). On the basis of the nuclear shell model, the next double magic shell-closure beyond sup 2 sup 0 sup 8 Pb is predicted at proton numbers between Z=114 and 126 and at neutron number N=184. All experimental efforts aiming at identifying SHEs (Z>=114) were negative so far. A highly sensitive search experiment was performed in November-December 1995 at SHIP. The isotope sup 2 sup 9 sup 0 116 produced by 'radiative capture' was searched for in the course of a 33 days irradiation of a sup 2 sup 0 sup 8 Pb target with sup 8 sup 2 Se projectiles, however, only cross-section limits were measured. Positive results were obtained in experiments searching for elements from 110 to 112 using cold fusion and the 1n evaporation channel. The produced isotopes were unambiguously identified by means of alpha-alpha correlations. Not fission, but alpha emission is the dominant decay mode. The measurement ...

  10. Fuel element

    International Nuclear Information System (INIS)

    Hirose, Yasuo.

    1982-01-01

    Purpose: To increase the plenum space in a fuel element used for a liquid metal cooled reactor. Constitution: A fuel pellet is secured at one end with an end plug and at the other with a coil spring in a tubular container. A mechanism for fixing the coil spring composed of a tubular unit is mounted by friction with the inner surface of the tubular container. Accordingly, the recoiling force of the coil spring can be retained by fixing mechanism with a small volume, and since a large amount of plenum space can be obtained, the internal pressure rise in the cladding tube can be suppressed even if large quantities of fission products are discharged. (Kamimura, M.)

  11. Nanoporous Al sandwich foils using size effect of Al layer thickness during Cu/Al/Cu laminate rolling

    Science.gov (United States)

    Yu, Hailiang; Lu, Cheng; Tieu, A. Kiet; Li, Huijun; Godbole, Ajit; Kong, Charlie

    2018-06-01

    The roll bonding technique is one of the most widely used methods to produce metal laminate sheets. Such sheets offer interesting research opportunities for both scientists and engineers. In this paper, we report on an experimental investigation of the 'thickness effect' during laminate rolling for the first time. Using a four-high multifunction rolling mill, Cu/Al/Cu laminate sheets were fabricated with a range of thicknesses (16, 40, 70 and 130 μm) of the Al layer. The thickness of the Cu sheets was a constant 300 μm. After rolling, TEM images show good bonding quality between the Cu and Al layers. However, there are many nanoscale pores in the Al layer. The fraction of nanoscale pores in the Al layer increases with a reduction in the Al layer thickness. The finite element method was used to simulate the Cu/Al/Cu rolling process. The simulation results reveal the effect of the Al layer thickness on the deformation characteristics of the Cu/Al/Cu laminate. Finally, we propose that the size effect of the Al layer thickness during Cu/Al/Cu laminate rolling may offer a method to fabricate 'nanoporous' Al sandwich laminate foils. Such foils can be used in electromagnetic shielding of electrical devices and noisy shielding of building.

  12. The effect of the addition of the elements Ni, Zn and Co in a composite AlTiO{sub 2} obtained by high-energy milling and sintering process; Efeito da adicao dos elementos Ni, Zn ou Co no composito AlTiO{sub 2} obtido por moagem de alta energia e sinterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, C.O. de; Coelho, R.E.; Conrado, L.C.; Nascimento, C.S.; Teixeira, C.A.; Mendonca, E.S., E-mail: cristiane.olv.carvalho@hotmail.com [Instituto Federal de Educacao, Ciencia e Tecnologia da Bahia (IFBA), BA (Brazil)

    2016-07-01

    The present work use aluminum scrap with addition of TiO{sub 2}, Ni, Zn or Co to preparation and characterization of nanocomposites. The aluminum were cut and subjected to high energy milling for 2 hours at 1200rpm. The obtained powder was added to TiO{sub 2}, Ni, Zn or Co in a nominal composition 97Al-2TiO{sub 2}-1X (X = Ni, Zn or Co) (weight %) and again, the mixture was subjected to milling for 1 hour at 1000rpm. Grinding powders were hot pressed in the closed die and then removed; the compressed were sintered at 950°C in a tubular furnace N{sub 2} passing atmosphere. The samples obtained were characterized by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD). The results of SEM images showed a very refined microstructure and an aluminum matrix without porosity. (author)

  13. Studies on SiC(p) reinforced Al-Al sub 3 Ni eutectic matrix composites

    International Nuclear Information System (INIS)

    Masrom, A.K.; Foo, L.C.; Ismail, A.B.

    1996-01-01

    An investigation on processing of Al-5.69wt% Ni eutectic with SiC particulate composites is reported. The intermetallic composites are prepared by elemental powder metallurgy route and sintered at two different temperatures, i.e., 600 degree C and 620 degree C. Results show that the metal matrix was Al-Al sub 3 Ni eutectic. The phase analysis by XRD identified the presence of Al sub 3 Ni and Al as dominant phases together with silicon and Al sub 4 C sub 3 phase as minor phases. The Al sub 4 C sub 3 and Si phases are formed during sintering due to SiC-Al interface reaction. SEM micrographs also reveal the formation of microvoid surrounding the SiC particle

  14. أواصر العناصر الكونية من منظور الأستاذ النورسي - Dr. ‘Uthman Muhammad Gharib: The Bonds of the Universal Elements from the Viewpoint of Bedi‘uzzaman al-Nursi

    OpenAIRE

    غريب, د. عثمان محمد

    2015-01-01

    أواصر العناصر الكونية من منظور ا أواصر العناصر الكونيةمن منظور الأستاذ بديع الزمان النورسي -ABSTRACT- The Bonds of the Universal Elements from the Viewpoint of Bedi'uzzaman al-Nursi Dr. 'Uthman Muhammad Gharib The researcher indicates the bonds of the elements of the universe as reflected in the "Nur Letters", which is a vision that elucidates the comprehensive identity of man. That identity is connected to the manifestations of existence and elements in the universe and i...

  15. All About ALS

    Science.gov (United States)

    ... Subscribe August 2015 Print this issue All About ALS Understanding a Devastating Disorder En español Send us ... Sports Concussions Wise Choices How Can I Help ALS Research? If you have ALS, join the National ...

  16. 合金元素对电弧熔炼TiC/Ti-6Al-4V复合材料中TiC生长形态的影响%Effects of Alloying Elements on Growth and Morphology of TiC in Arc-Melted TiC/Ti-6Al-4V Composites

    Institute of Scientific and Technical Information of China (English)

    曹磊; 王宏伟; 邹鹑鸣; 魏尊杰

    2010-01-01

    采用非自耗电弧熔炼制备含不同微合金元素的10vol%TiC/Ti-6Al-4V复合材料,研究不同的微量合金元素对复合材料中TiC形态的影响.结果表明,原始铸态复合材料中TiC形态主要是粗大且发达的枝晶状.而基体中加入0.3%(质量分数,下同)的Sn元素后,TiC生长被抑制,TiC形态变为细小分散的颗粒状;0.3%的Ni被加入后,增大了TiC的结晶区间,使TiC枝晶生长变得更加发达;而0.3%的Nb元素的加入,则减小了TiC的结晶区间,从而减少了初晶TiC数量,促进了共晶TiC的形成.

  17. Phase relations in the pseudobinary systems RAO3-R2Ti2O7 (R: rare earth element and Y, A: Fe, Ga, Al, Cr and Mn) and syntheses of new compounds R(A1-xTix)O3+x/2 (2/3≤x≤3/4) at elevated temperatures in air

    Science.gov (United States)

    Brown, Francisco; Jacobo-Herrera, Ivan; Alvarez-Montaño, Victor; Kimizuka, Noboru; Kurashina, Keiji; Michiue, Yuichi; Matsuo, Yoji; Mori, Shigeo; Ikeda, Naoshi; Medrano, Felipe

    2017-07-01

    Phase relations in the pseudo-binary systems RFeO3-R2Ti2O7 (R: Lu, Ho and Dy), RGaO3-R2Ti2O7 (R: Lu and Er), LuAlO3-Lu2Ti2O7 and RAO3-R2Ti2O7 (R: Lu and Yb. A: Cr and Mn) at elevated temperatures in air were determined by means of a classic quenching method. There exist Lu(Fe1-xTix)O3+x/2, R(Ga1-xTix)O3+x/2 (R: Lu and Er) and Lu(Al1-xTix)O3+x/2 (2/3≤ x≤3/4) having the Yb(Fe1-xTix)O3+x/2-type of crystal structure (x=0.72, space group: R3m, a(Å)=17.9773 and c(Å)=16.978 as a hexagonal setting) in these pseudo binary systems. Eighteen compounds R(A1-xTix)O3+x/2 (R: Lu-Sm and Y, A: Fe, Ga and Al) were newly synthesized and their lattice constants as a hexagonal setting were measured by means of the X-ray powder diffraction method. The R occupies the octahedral site and both A and Ti does the trigonalbipyramidal one in these compounds. Relation between lattice constants for the rhombic R(A1-xTix)O3+x/2 and the monoclinic In(A1-xTix)O3+x/2 are as follows, ah≈5 x bm, ch≈3 x cm x sin β and am=31/2 x bm, where ah and ch are the lattice constants as a hexagonal setting for R(A1-xTix)O3+x/2 and am, bm, cm and β are those of the monoclinic In(A1-xTix)O3+x/2. Crystal structural relationships among α-InGaO3 (hexagonal, high pressure form, space group: P63/mmc), InGaO3 (rhombic, hypothetical), (RAO3)n(BO)m and RAO3(ZnO)m (R: Lu-Ho, Y and In, A: Fe, Ga, and Al, B: divalent cation element, m, n: natural number), the orthorhombic-and monoclinic In(A1-xTix)O3+x/2 (A: Fe, Ga, Al, Cr and Mn) and the hexagonal-and rhombic R(A1-xTix)O3+x/2 (R: Lu-Sm and Y, A: Fe, Ga and Al) are schematically presented. We concluded that the crystal structures of both the α-InGaO3 (high pressure form, hexagonal, space group: P63/mmc) and the hypothetical InGaO3 (rhombic) are the key structures for constructing the crystal structures of these compounds having the cations with CN=5.

  18. Instability of TiC and TiAl3 compounds in Al-10Mg and Al-5Cu alloys by addition of Al-Ti-C master alloy

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The performance of Al-Ti-C master alloy in refining Al-10Mg and A1-5Cu alloys was studied by using electron probe micro-analyzer (EPMA) and X-ray diffractometer (XRD) analysis.The results indicate that there are obvious fading phenomena in both Al-10Mg and Al-5Cu alloys with the addition of Al-5Ti-0.4C refiner which contains TiC and TiAl3 compounds.Mg element has no influence on the stability of TiC and TiAl3, while TiC particles in Al-10Mg alloy react with Al to form Al4C3 particles, resulting in the refinement fading.However, TiC particles are relatively stable in Al-5Cu alloy, while TiAl3 phase reacts with Al2Cu to produce a new phase Ti(Al, Cu)2, which is responsible for the refinement fading in Al-5Cu alloy.These indicate that the refinement fading will not occur only when both the TiC particles and TiAl3 compound of Al-Ti-C refiner are stable in Al alloys.

  19. De la geoquimica al paisaje: composicion elemental de los suelos

    NARCIS (Netherlands)

    Martinez-Cortizas, A.; Costa-Casais, M.; Kaal, J.; Ferro-Vazquez, C.; Pontevedra-Pombal, X.; Viveen, W.

    2013-01-01

    El objeto de este libro es el estudio del arte rupestre en la Edad de Bronce hasta la Edad del Hierro en Campo Lameiro (Pontevedra, Galicia), en el que se ha combinado la metodología arqueológica, histórica, etnográfica y paleoambitental, para completar el contexto arqueológico de los petroglifos

  20. Al-Si/Al2O3 in situ composite prepared by displacement reaction of CuO/Al system

    Directory of Open Access Journals (Sweden)

    Zhang Jing

    2010-02-01

    Full Text Available Al2O3 particle-reinforced ZL109 composite was prepared by in situ reaction between CuO and Al. The microstructure was observed by means of OM, SEM and TEM. The Al2O3 particles in sub-micron sizes distribute uniformly in the matrix, and the Cu displaced from the in situ reaction forms net-like alloy phases with other alloy elements. The hardness and the tensile strength of the composites at room temperature have a slight increase as compared to that of the matrix. However, the tensile strength at 350 ℃ has reached 90.23 MPa, or 16.92 MPa higher than that of the matrix. The mechanism of the reaction in the CuO/Al system was studied by using of differential scanning calorimetry(DSC and thermodynamic calculation. The reaction between CuO and Al involves two steps. First, CuO reacts with Al to form Cu2O and Al2O3 at the melting temperature of the matrix alloy, and second, Cu2O reacts with Al to form Cu and Al2O3 at a higher temperature. At ZL109 casting temperature of 750–780 ℃, the second step can also take place because of the effect of exothermic reaction of the first step.

  1. Comparison of irradiation behavior of different uranium silicide dispersion fuel element designs

    International Nuclear Information System (INIS)

    Hofman, G.L.; Rest, J.; Snelgrove, J.L.

    1995-01-01

    Calculations of fuel swelling of U 3 SiAl-Al and U 3 Si 2 were performed for various dispersion fuel element designs. Breakaway swelling criteria in the form of critical fuel volume fractions were derived with data obtained from U 3 SiAl-Al plate irradiations. The results of the analysis show that rod-type elements remain well below the pillowing threshold. However, tubular fuel elements, which behave essentially like plates, will likely develop pillows or blisters at around 90% 235 U burnup. The U 3 Si 2 -Al compounds demonstrate stable swelling behavior throughout the entire burnup range for all fuel element designs

  2. Molecular clusters of the main group elements

    CERN Document Server

    Driess, Matthias

    2008-01-01

    ""To summarize, Molecular Clusters of the Main Group Elements is certainly not a popular science book, nor is it a textbook; it is a very good, up-to-date collection of articles for the specialist. Als Fazit bleibt: Molecular Clusters of the Main Group Elements ist sicher kein populissenschaftliches Werk, auch kein Lehrbuch, aber eine gelungene, hoch aktuelle Zusammenstellung fen interessierten Fachmann."" -Michael Ruck, TU Dresden, Angewandte Chemie, 2004 - 116/36 + International Edition 2004 - 43/36

  3. preliminary phytochemical screening, proximate and elemental

    African Journals Online (AJOL)

    DR. AMINU

    1*Kawo, A.H., 1Abdullahi, B.A., 2Gaiya, Z.A. 3Halilu, A., 4Dabai, M. and 5Dakare, M.A. ... mineral elements in the seed powder were: Al (144 ± 4 ppm), Ca (602 ± 122 ppm), K (732 ± 164 .... elements as Sr (69 ± 3.0), Rb (122 ± 0.0) and Zr (11.

  4. Trace elements determination in human hair

    International Nuclear Information System (INIS)

    Carrion, Jose

    1995-01-01

    Concentrations of Cu, Zn, Pb, Mg, Ca, Na, K, Mn, Cr, Ni, Co, V, Cd and Al, in human hair sampled from 23 young men during 24 months were determined by atomic absorption spectroscopy. Additional determination of mercury and volatile elements were made by using accessory MHS-10. Statistical treatment of data is presented for each person and element. The pre-treatment of hair carried out with an organic solvent to remove the superficial pollutants is explained. (The author)

  5. Characteristics of mechanical alloying of Zn-Al-based alloys

    International Nuclear Information System (INIS)

    Zhu, Y.H.; Hong Kong Polytechnic; Perez Hernandez, A.; Lee, W.B.

    2001-01-01

    Three pure elemental powder mixtures of Zn-22%Al-18%Cu, Zn-5%Al-11%Cu, and Zn-27%Al-3%Cu (in wt.%) were mechanically alloyed by steel-ball milling processing. The mechanical alloying characteristics were investigated using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy techniques. It was explored that mechanical alloying started with the formation of phases from pure elemental powders, and this was followed by mechanical milling-induced phase transformation. During mechanical alloying, phases stable at the higher temperatures formed at the near room temperature of milling. Nano-structure Zn-Al-based alloys were produced by mechanical alloying. (orig.)

  6. AL(0) in municipal waste incinerator ash

    Science.gov (United States)

    Stipp, S. L.; Ronsbo, J. G.; Zunic, T. B.; Christensen, T. H.

    2003-04-01

    Disposal of municipal waste is a challenge to society. Waste volume is substantially decreased by incineration but residual ash usually contains a number of toxic components which must be immobilised to insure environmental protection. One element, chromium, is mobile and toxic in its oxidised state as Cr(VI) but it can be reduced to Cr(III) and immobilised. Reduction can be promoted by ash treatment with Fe(0) or Fe(II), but recent evidence shows that at least some Cr(VI) is reduced spontaneously in the ash. Aspects of ash behaviour suggest metallic aluminium as the reducing agent, but no direct evidence of Al(0) has been found until now. We examined filter ash from an energy-producing, municipal-waste incinerator (Vest-forbrænding) near Copenhagen. X-ray diffraction (XRD) identified expected salts of Na, K and Ca such as halite, sylvite, calcite, anhydrite and gypsum as well as quartz, feldspar and some hematite. Wave-dispersive electron microprobe produced elemen-tal maps of the ash; Al-rich areas were analysed quantitatively by comparison with standards. We identified metallic Al particles, averaging 50 to 100 micrometers in di-ameter, often with a fractured, glassy border of aluminum oxide. The particles were porous, explaining fast Cr(VI) reduction and they contained thin exsolution lamellae of Al-alloys of Pb and Cu or Mn, Fe and Ag, which provide clues of the Al(0) origin in the waste. Sometimes Al(0) occurred inside glassy globes of Al2O3. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) and X-ray photoelectron spectroscopy (XPS) proved that surface Al concentrations on ash particles were below detection, confirming reactivity of the Al(0) bulk. The persistence of reduced Al through the highly oxidising combustion procedure comes as a surprise and is a benefit in the immobilisation of Cr(VI) from municipal-waste incineration residues.

  7. Towards an elastic model of wurtzite AlN nanowires

    International Nuclear Information System (INIS)

    Mitrushchenkov, A; Chambaud, G; Yvonnet, J; He, Q-C

    2010-01-01

    Starting with ab initio calculations of AlN wurtzite [0001] nanowires with diameters up to 4 nm, a finite element method is developed to deal with larger nanostructures/nanoparticles. The ab initio calculations show that the structure of the nanowires can be well represented by an internal part with AlN bulk elastic properties, and one atomic surface layer with its own elastic behavior. The proposed finite element method includes surface elements with their own elastic properties using surface elastic coefficients deduced from the ab initio calculations. The elastic properties obtained with the finite element model compare very well with those obtained with the full ab initio calculations.

  8. Discrete Element Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Morris, J; Johnson, S

    2007-12-03

    The Distinct Element Method (also frequently referred to as the Discrete Element Method) (DEM) is a Lagrangian numerical technique where the computational domain consists of discrete solid elements which interact via compliant contacts. This can be contrasted with Finite Element Methods where the computational domain is assumed to represent a continuum (although many modern implementations of the FEM can accommodate some Distinct Element capabilities). Often the terms Discrete Element Method and Distinct Element Method are used interchangeably in the literature, although Cundall and Hart (1992) suggested that Discrete Element Methods should be a more inclusive term covering Distinct Element Methods, Displacement Discontinuity Analysis and Modal Methods. In this work, DEM specifically refers to the Distinct Element Method, where the discrete elements interact via compliant contacts, in contrast with Displacement Discontinuity Analysis where the contacts are rigid and all compliance is taken up by the adjacent intact material.

  9. EXPERIMENT AL AND THEORETICAL STUDY OF PRECAST ...

    African Journals Online (AJOL)

    EXPERIMENT AL AND THEORETICAL STUDY OF PRECAST BEAM-SLAB. CONSTRUCTION. Girma Zerayohannes and Adil Zekaria. Department of Civil Engineering. Addis Ababa University. ABSTRACT. The use of partially precast beam elements ivith shear connectors in slab construction relieves the requirement of ...

  10. Idaaratu al Wahdah al Namthiyah li at Tathwiri al Tarbiyah al Islamiyah

    Directory of Open Access Journals (Sweden)

    Ahmad Danusiri

    2016-04-01

    Full Text Available Islam, through the Quran, proclaims that its mission includes the teachings to the whole universe, Everything in the universe is maintained by Islam, and none of the symptoms are ignored. The revelations also include the traditions of the Prophet that are authentic (shahih and good (hasan in quality. Both the Quran and maqbulah hadiths are accepted by Muslims on the basis of faith. When some experts of UIN Walisongo from various disciplines try to understand the sacred words of these two resources, their understanding continues, reaching the paradigm of the unity of science which essentially unites the normative, social, and natural sciences. The effect of this paradigm has brought up an issue for the author. Is there any hadiths or Prophetic traditions that can be used as a grand theory in the management disciplines of Islamic education.To address this issue, the authors conducted a literature research with the title Development of Islamic Education Management Module. Sources of data were focused on nine books of Hadiths : Sahih al-Bukhari, Sahih al-Muslim, Sunan Abu Dawud, Sunan at-Turmudzi, Sunan an-Nasai, Sunan Ibn Majah, Sunan ad-Darimi, Muwatta Malik, and Musnad Imam Ahmad bin Hanbal in the form of digital data Lidwa Reader Software Book 9 Imam Hadith. The findings of the study stated that the meaning of the word Rabb includes: creating, nurturing, maintaining, teaching, educating, and organizing. Thus, in an academic term, the word Rabb implies a manager or leader. Meanwhile, in the concept of comprehensive manager it contains at least 14 nomenclature denotations: planning, responsibility, organization, coordination, system of employee payroll, learning, resources, humanity, principle of making it easier for the manager to the employee, motivated to achieve optimal performance, preventing unproductivity, education participation, institutional costs, monitoring, and evaluation system. Each nomenclature has numerous hadiths that could serve

  11. Bankole et al (2)

    African Journals Online (AJOL)

    DELL

    Relationships of Clay-filled Channels on the Delta Flanks (Modified after Doust and Omatsola, 1990 and Lawrence et al., 2002). ... and in the Indo-Malaysian area (Germeraad et al.,. 1968). The genus ..... Upper Cretaceous of British Guiana.

  12. Lou Gehrig's Disease (ALS)

    Science.gov (United States)

    ... disease. Who Gets ALS? Although this disease can strike anyone, ALS is extremely rare in kids. According ... home to provide care that the family cannot handle alone. Living With Lou Gehrig's Disease Living with ...

  13. Aussprache als motorische Fertigkeit

    DEFF Research Database (Denmark)

    Bonner, Maria

    2013-01-01

    Authentische Aussprache gilt im Fremdsprachenunterricht als schwer erreichbares Ziel, fremdsprachlicher Akzent wird als nahezu unvermeidbar gesehen. Weder die Hypothese einer kritischen Periode für den Erwerb einer authentischen Aussprache noch das Konzept der Fossilierung im Sprachlernprozess...

  14. Amyotrophic lateral sclerosis (ALS)

    Science.gov (United States)

    Lou Gehrig disease; ALS; Upper and lower motor neuron disease; Motor neuron disease ... One out of 10 cases of ALS is due to a genetic defect. The cause is unknown in most other cases. In ALS, motor nerve cells (neurons) waste away ...

  15. Nuclear responses in INTOR plasma stabilization elements

    International Nuclear Information System (INIS)

    Gohar, Y.; Gilligan, J.; Jung, J.; Mattas, R.F.; Miley, G.H.; Wiffen, F.W.; Yang, S.

    1985-01-01

    Nuclear responses in the plasma stabilization elements were studied in a parametric fashion as a part of the transient electromagnetics critical issue C of ETR/INTOR activity. The main responses are neutron fluence and radiation dose in the insulator material, induced resistivity and atomic displacement in the conductor material, nuclear heating and life analysis for the elements. Copper and aluminum conductors with either MgAl 2 O 4 or MgO insulating material were investigated. Radiation damage and life analysis for these elements were also discussed

  16. andoh et al

    African Journals Online (AJOL)

    PUBLICATIONS1

    CYLINDRICAL ELEMENT AND A DEFORMABLE FLAT. SURFACE ... order to position the sensing elements into the roll body. An experiment was ... The mechanics of friction are complex, and the ..... and Practice, Elsevier Science Ltd., New.

  17. Chemistry of the elements

    International Nuclear Information System (INIS)

    Greenwood, N.N.; Earnshaw, A.

    1984-01-01

    This textbook presents an account of the chemistry of the elements for both undergraduate and postgraduate students. It covers not only the 'inorganic' chemistry of the elements, but also analytical, theoretical, industrial, organometallic;, bio-inorganic and other areas of chemistry which apply. The following elements of special nuclear interest are included: Rb, Cs, Fr, Sr, Ba, Ra, Po, At, Rn, Sc, Y, Zr, Hf, V, Nb, Ta, Mo, Tc, Ru, the Lanthanide Elements, the Actinide Elements. (U.K.)

  18. Concentration of stable elements in food products

    International Nuclear Information System (INIS)

    Montford, M.A.; Shank, K.E.; Hendricks, C.; Oakes, T.W.

    1980-01-01

    Food samples were taken from commercial markets and analyzed for stable element content. The concentrations of most stable elements (Ag, Al, As, Au, Ba, Br, Ca, Ce, Cl, Co, Cr, Cs, Cu, Fe, Hf, I, K, La, Mg, Mn, Mo, Na, Rb, Sb, Sc, Se, Sr, Ta, Th, Ti, V, Zn, Zr) were determined using multiple-element neutron activation analysis, while the concentrations of other elements (Cd, Hg, Ni, Pb) were determined using atomic absorption. The relevance of the concentrations found are noted in relation to other literature values. An earlier study was extended to include the determination of the concentration of stable elements in home-grown products in the vicinity of the Oak Ridge National Laboratory. Comparisons between the commercial and local food-stuff values are discussed

  19. ILM AL LUGHAH AL IJTIMAI WA TALIM AL LUGHAH AL ARABIYYAH LI AL NATHIQINA BI GHAIRIHA

    Directory of Open Access Journals (Sweden)

    Ahmad Ubaedillah Fathuddin

    2017-03-01

    Full Text Available Language learning cannot work without integrating other fields of knowledge such as psychology, anthropology, sociolinguistics, etc. Sociolinguistics is a branch of linguistics which discusses about language due to social factors. It has an important role in language learning especially in making it easily understandable for the language learners by understanding the language use of the native speakers. The contribution of sociolinguistics in Arabic language learning for foreign language learners can be seen from the relationship between language and social environment. In this case, it does not only learn about the elements or internal systems of Arabic language such as phonology, syntax, and morphology, but also the social context such as speech community, social class, language use and culture. It means sociolinguistics gives information about the definition and use of Arabic language based on the social context.

  20. 143 - 148_Makeri et al.

    African Journals Online (AJOL)

    USER

    2015-06-01

    Jun 1, 2015 ... Yuan et al., 2003), antimicrobial activity (Sundarrao et al., 1993; Betancur-Galvis et al., 1999; Takashi et al., 2006), anti-parasitic, anti-malarial activities (Alali et al., 1998; Jaramillo et al., 2000; Luna et al.,. 2005). This study evaluates the antibacterial activity of extract of stem –bark and leaf extracts of Annona.

  1. Attempt to produce silicide fuel elements in Indonesia

    International Nuclear Information System (INIS)

    Soentono, S.; Suripto, A.

    1991-01-01

    After the successful experiment to produce U 3 Si 2 powder and U 3 Si 2 -Al fuel plates using depleted U and Si of semiconductor quality, silicide fuel was synthesized using x -Al available at the Fuel Element Production Installation (FEPI) at Serpong, Indonesia. Two full-size U 3 Si 2 -Al fuel elements, having similar specifications to the ones of U 3 O 8 -Al for the RSG-GAS (formerly known as MPR-30), have been produced at the FEPI. All quality controls required have been imposed to the feeds, intermediate, as well as final products throughout the production processes of the two fuel elements. The current results show that these fuel elements are qualified from fabrication point of view, therefore it is expected that they will be permitted to be tested in the RSG-GAS, sometime by the end of 1989, for normal (∝50%) and above normal burn-up. (orig.)

  2. Platinum group elements geochemistry of ultramafic and associated ...

    Indian Academy of Sciences (India)

    group element (PGE) and associated gold mineralization in these ultramafic rocks. A mineral ... Paleoproterozoic age, mostly emplaced into the .... tified reference materials (CRM) from the US Geo- ..... Classification diagram (Barnes et al.

  3. Abu al-Layth al-Libi

    Science.gov (United States)

    2015-02-01

    success. As an Arab participant acknowledged very early on, “the situation was really harsh. All the brothers were tired,” as they lacked food and... glorious battles that occurred during the early Islamic period.133 He stressed the importance of the battlefield as the path to achieve honor and dignity...diaspora in Waziristan. In the words of Walid Othmani, a French jihadi trained by al-Qa`ida in Waziristan in 2008, “[Al-Libi] was someone well-known and

  4. A study of ion damage in Al, Al/Cu and Al/Ag

    International Nuclear Information System (INIS)

    Marikar, P.

    1979-06-01

    Specimens of pure aluminium, aluminium-copper and aluminium-silver have been irradiated with 20 keV helium ions and/or 100 keV aluminium ions and the nature of the damage assessed using transmission electron microscopy. Irradiation with 20 keV helium ions to a dose of 2.7 x 10 15 ions cm -2 results in the formation of interstitial loops and helium gas bubbles. The helium bubbles were detectable only after annealing at a high temperature following irradiation. When the helium preinjected aluminium specimens were irradiated with 100 keV Al + ions to a dose of 84 dpa at temperatures above 150 0 C, voids were observed to form. At a lower dose of 64 dpa, only a high density of dislocation loops was observed. Al-1 wt% Cu alloy containing partially coherent theta' precipitates resists void formation to a considerable extent, and Al-10 wt% Ag alloy containing coherent G.P. zones offers complete resistance to both dislocation loop nucleation and void formation. The experimental results are discussed in the light of the current theories of irradiation induced damage in metals. The importance of the dislocation-sink efficiency for point defects, the gaseous impurity and the alloying elements in determining void formation is highlighted. (author)

  5. Effect of a three-month football training program on trace element ...

    African Journals Online (AJOL)

    Yomi

    2012-01-03

    Jan 3, 2012 ... physical exercise and trace element metabolism (Marrella et al., 1993; McDonald ..... induced stress and immune function. Exerc Immunol Rev. ... aerobic exercise upon the trace element levels in blood. Neuro. Endocrinol.

  6. AlGaN nanocolumns and AlGaN/GaN/AlGaN nanostructures grown by molecular beam epitaxy

    Energy Technology Data Exchange (ETDEWEB)

    Ristic, J.; Sanchez-Garcia, M.A.; Ulloa, J.M.; Calleja, E. [Departamento de Ingenieria Electronica, ETSI Telecomunicacion, Universidad Politecnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Sanchez-Paramo, J.; Calleja, J.M. [Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Jahn, U.; Trampert, A.; Ploog, K.H. [Paul-Drude-Institut fuer Festkoerperelektronik, Hausvogteiplatz 5-7, 10117 Berlin (Germany)

    2002-12-01

    This work reports on the characterization of hexagonal, single crystal AlGaN nanocolumns with diameters in the range of 30 to 100 nm grown by molecular beam epitaxy on Si(111) substrates. The change of the flux ratio between the Al and the total III-element controls the alloy composition. The Al composition trend versus the Al flux is consistent both with the E{sub 2} phonon energy values measured by inelastic light scattering and the luminescence emission peaks position. High quality low dimensional AlGaN/GaN/AlGaN heterostructures with five GaN quantum discs, 2 and 4 nm thick, embedded into the AlGaN columns, were designed in order to study the quantum confinement effects. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

  7. Pornographie als Metapher

    Directory of Open Access Journals (Sweden)

    Caroline Schubarth

    2010-02-01

    Full Text Available In diesem Artikel werden unterschiedliche metaphorische Verwendungen des Pornografiebegriffs und deren Implikationen untersucht. Während die Existenz von Pornografie der feministischen Anti-Porno-Bewegung als Erklärung für die anhaltende Diskriminierung von Frauen in westlichen Gesellschaften dient, nutzen rechtskonservative Kräfte den Pornografievorwurf als Rechtfertigung für die Zensur von als deviant empfundenen Identitäten und sexuellen Praktiken.

  8. Predicting glass-forming compositions in the Al-La and Al-La-Ni systems

    International Nuclear Information System (INIS)

    Gargarella, P.; de Oliveira, M.F.; Kiminami, C.S.; Pauly, S.; Kuehn, U.; Bolfarini, C.; Botta, W.J.; Eckert, J.

    2011-01-01

    Research highlights: → The glass-forming ability of the Al-La and Al-La-Ni systems was studied using the λ* and the λ.Δe criteria. → Both criteria predicted with just 1% at. of error the best glass-former verified so far in the Al-La system. → Four new glass-former compositions could be predicted in the Al-La-Ni system using the λ.Δe criterion. → The best glass-former reported so far in the Al-La-Ni system was found. - Abstract: In this work, a criterion considering the topological instability (λ) and the differences in the electronegativity of the constituent elements (Δe) was applied to the Al-La and Al-Ni-La systems in order to predict the best glass-forming compositions. The results were compared with literature data and with our own experimental data for the Al-La-Ni system. The alloy described in the literature as the best glass former in the Al-La system is located near the point with local maximum for the λ.Δe criterion. A good agreement was found between the predictions of the λ.Δe criterion and literature data in the Al-La-Ni system, with the region of the best glass-forming ability (GFA) and largest supercooled liquid region (ΔT x ) coinciding with the best compositional region for amorphization indicated by the λ.Δe criterion. Four new glassy compositions were found in the Al-La-Ni system, with the best predicted composition presenting the best glass-forming ability observed so far for this system. Although the λ.Δe criterion needs further refinements for completely describe the glass-forming ability in the Al-La and Al-La-Ni systems, the results demonstrated that this criterion is a good tool to predict new glass-forming compositions.

  9. Al2O3 adherence on CoCrAl alloys

    International Nuclear Information System (INIS)

    Kingsley, L.M.

    1980-04-01

    Adherence of protective oxides on NiCrAl and CoCrAl superalloys has been promoted by a dispersion of a highly oxygen reactive element or its oxide being produced within the protection system. Two aspects of this subject are investigated here: the use of Al 2 O 3 as both the dispersion and protective oxide; and the production of an HfO 2 dispersion while simultaneously aluminizing the alloy. It was found that an Al 2 O 3 dispersion will act to promote the adherence of an external scale of Al 2 O 3 to a degree comparable to previously tested dispersions and an HfO 2 dispersion comparable to that produced by a Rhines pack treatment is produced during aluminization

  10. Data Element Registry Services

    Data.gov (United States)

    U.S. Environmental Protection Agency — Data Element Registry Services (DERS) is a resource for information about value lists (aka code sets / pick lists), data dictionaries, data elements, and EPA data...

  11. Basic Finite Element Method

    International Nuclear Information System (INIS)

    Lee, Byeong Hae

    1992-02-01

    This book gives descriptions of basic finite element method, which includes basic finite element method and data, black box, writing of data, definition of VECTOR, definition of matrix, matrix and multiplication of matrix, addition of matrix, and unit matrix, conception of hardness matrix like spring power and displacement, governed equation of an elastic body, finite element method, Fortran method and programming such as composition of computer, order of programming and data card and Fortran card, finite element program and application of nonelastic problem.

  12. Rupture of Al matrix in U-Mo/Al dispersion fuel by fission induced creep

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Gwan Yoon; Sohn, Dong Seong [UNIST, Daejeon (Korea, Republic of); Kim, Yeon Soo [Argonne National Laboratory, Argonnge (United States); Lee, Kyu Hong [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    This phenomenon was found specifically in the dispersion fuel plate with Si addition in the Al matrix to suppress interaction layer (IL) formation between UMo and Al. It is known that the stresses induced by fission induced swelling in U-Mo fuel particles are relieved by creep deformation of the IL, surrounding the fuel particles, that has a much higher creep rate than the Al matrix. Thus, when IL growth is suppressed, the stress is instead exerted on the Al matrix. The observed rupture in the Al matrix is believed to be caused when the stress exceeded the rupture strength of the Al matrix. In this study, the possibility of creep rupture of the Al matrix between the neighboring U-Mo fuel particles was examined using the ABAQUS finite element analysis (FEA) tool. The predicted rupture time for a plate was much shorter than its irradiation life indicating a rupture during the irradiation. The higher stress leads Al matrix to early creep rupture in this plate for which the Al matrix with lower creep strain rate does not effectively relieve the stress caused by the swelling of the U-Mo fuel particles. For the other plate, no rupture was predicted for the given irradiation condition. The effect of creeping of the continuous phase on the state of stress is significant.

  13. Radiolabelled cellular blood elements

    International Nuclear Information System (INIS)

    Sinzinger, H.

    1990-01-01

    This book reports on radiolabelled cellular blood elements, covering new advances made during the past several years, in particular the use of Tc-99 as a tracer for blood elements. Coverage extends to several radiolabelled monoclonal antibodies that are specific for blood components and may label blood elements in vivo

  14. Alles is al uitgevonden

    NARCIS (Netherlands)

    J.G.M. van Marrewijk (Charles)

    1996-01-01

    textabstractDe voordelen van vrijhandel zijn zeer beperkt, al-thans als we de empirische schattingen van vooraanstaande economen en internationale organisaties mogen geloven. Zo worden de voordelen van liberalisatie voor de Europese Unie geraamd op ongeveer 0,5% van het bnp 1. De door het IMF

  15. Lukman et al. (5)

    African Journals Online (AJOL)

    DELL

    1 Civil Engineering Department, Obafemi Awolowo University, Ile-Ife- Nigeria and Corresponding author. 2Department of Water Resources and Environmental Engineering, Ahmadu Bello University, Samaru, Zaria- Nigeria s Department of Civil Engineering, University of Hafr Al-Batin, Hafr Al-Batin, Saudi Arabia.

  16. Rare (Earth Elements [score

    Directory of Open Access Journals (Sweden)

    Camilo Méndez

    2014-12-01

    Full Text Available Rare (Earth Elements is a cycle of works for solo piano. The cycle was inspired by James Dillon’s Book of Elements (Vol. I-V. The complete cycle will consist of 14 pieces; one for each selected rare (earth element. The chosen elements are Neodymium, Erbium, Tellurium, Hafnium, Tantalum, Technetium, Indium, Dysprosium, Lanthanium, Cerium, Europium, Terbium, Yttrium and Darmstadtium. These elements were selected due to their special atomic properties that in many cases make them extremely valuable for the development of new technologies, and also because of their scarcity. To date, only 4 works have been completed Yttrium, Technetium, Indium and Tellurium.

  17. Generalized finite elements

    International Nuclear Information System (INIS)

    Wachspress, E.

    2009-01-01

    Triangles and rectangles are the ubiquitous elements in finite element studies. Only these elements admit polynomial basis functions. Rational functions provide a basis for elements having any number of straight and curved sides. Numerical complexities initially associated with rational bases precluded extensive use. Recent analysis has reduced these difficulties and programs have been written to illustrate effectiveness. Although incorporation in major finite element software requires considerable effort, there are advantages in some applications which warrant implementation. An outline of the basic theory and of recent innovations is presented here. (authors)

  18. Assessment of elemental contamination in road dust using EDXRF

    International Nuclear Information System (INIS)

    Saradhi, I.V.; Sandeep, P.; Pandit, G.G.

    2014-01-01

    Road dust samples were collected in different locations of heavy traffic, medium traffic, express way and industrial areas of Mumbai. The concentrations of various elements (Mg, Al, K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn and Pb) in road dust samples were analyzed using EDXRF. The average elemental profile of road dust in Mumbai was comparable with studies carried out in other countries with slight variations. The estimated geo accumulation indices and enrichment factors indicated moderate elemental contamination and enrichment of anthropogenic elements in road dust samples. Factor analysis of elemental data resolved four sources namely crustal, tyre wear, vehicular/industrial emissions and break wear. (author)

  19. Macro-Elements and Trace Elements in Cereal Grains Cultivated in Latvia

    Directory of Open Access Journals (Sweden)

    Jākobsone Ida

    2015-09-01

    Full Text Available Cereal-based foods have great importance in the compensation of micro- and trace element deficiency, because 50% of the foods produced worldwide are made up of cereal grains. The aim of the research was to determine the concentration of macro-elements and trace elements in different cereals cultivated in Latvia. Various cereals were used in the research: rye (n = 45, barley (n = 54, spring wheat (n = 27, winter wheat (n = 53, triticale (n = 45 and oats (n = 42. Thirteen macro- and trace elements (Cd, Pb, Ni, Cr, Al, Cu, K, Na, Mn, Fe, Zn, Mg, Ca were determined in cereal grain samples (n = 266. Macro-elements and trace elements varied significantly (p < 0.01 or p < 0.001. The highest concentrations of macro- and trace elements were found in oats and the lowest in rye. The obtained data will expand the opportunity for food and nutrition scientists to evaluate content of the examined elements in grain products, and dietary consumption (bioavailability of the examined macro-elements and trace elements.

  20. Elements beyond uranium

    International Nuclear Information System (INIS)

    Seaborg, G.T.; Loveland, W.D.

    1990-01-01

    This book is the 12th volume in a series on transuranium elements. Varied techniques for production of these elements, the methods used in the identification, and the exquisitely refined microchemical techniques required to deal wth samples sometimes involving only a few atoms are described in detail. The chapter on synthesis of the new elements is liberally laced with reminiscences of the proud progenitors as well as the criteria for the discovery of a new chemical element. The authors lament that the superheavy elements (elements in the region of atomic number 114) still elude detection even though their creation should be possible, and some, at least, should survive long enough to be detected. One chapter in the book is devoted to practical applictions of uranium, and the transuranic elements

  1. Interview als Text vs. Interview als Interaktion

    Directory of Open Access Journals (Sweden)

    Arnulf Deppermann

    2013-09-01

    Full Text Available Das Interview ist nach wie vor das beliebteste sozialwissenschaftliche Verfahren des Datengewinns. Ökonomie der Erhebung, Vergleichbarkeit und die Möglichkeit, Einsicht in Praxisbereiche und historisch-biografische Dimensionen zu erhalten, die der direkten Beobachtung kaum zugänglich sind, machen seine Attraktivität aus. Zugleich mehren sich Kritiken, die seine Leistungsfähigkeit problematisieren, indem sie auf die begrenzte Reichweite der Explikationsfähigkeiten der Befragten, die Reaktivität der Erhebung oder die Differenz zwischen Handeln und dem Bericht über Handeln verweisen. Im Beitrag wird zwischen Ansätzen, die das Interview als Text, und solchen, die es als Interaktion verstehen, unterschieden. Nach dem Text-Verständnis werden Interviews unter inhaltlichen Gesichtspunkten analysiert und als Zugang zu einer vorgängigen sozialen oder psychischen Wirklichkeit angesehen. Das Interaktions-Verständnis versteht Interviews dagegen als situierte Praxis, in welcher im Hier und Jetzt von InterviewerInnen und Befragten gemeinsam soziale Sinnstrukturen hergestellt werden. Anhand ubiquitärer Phänomene der Interviewinteraktion – Fragen, Antworten und die Selbstpositionierung von InterviewerInnen und Befragten – werden Praktiken des interaktiv-performativen Handelns im Interview dargestellt. Ihre Relevanz für die Interviewkonstitution und ihre Erkenntnispotenziale für die Interviewauswertung werden aufgezeigt. Es wird dafür plädiert, die interaktive Konstitutionsweise von Interviews empirisch zu erforschen und methodisch konsequent zu berücksichtigen. URN: http://nbn-resolving.de/urn:nbn:de:0114-fqs1303131

  2. Elemental analysis with external-beam PIXE

    Science.gov (United States)

    Lin, E. K.; Wang, C. W.; Teng, P. K.; Huang, Y. M.; Chen, C. Y.

    1992-05-01

    A beamline system and experimental setup has been established for elemental analysis using PIXE with an external beam. Experiments for the study of the elemental composition of ancient Chinese potsherds (the Min and Ching ages) were performed. Continuum X-ray spectra from the samples bombarded by 3 MeV protons have been measured with a Si(Li) detector. From the analysis of PIXE data, the concentration of the main elements (Al, Si, K, and Ca) and of more than ten trace elements in the matrices and glazed surfaces were determined. Results for two different potsherds are presented, and those obtained from the glaze colorants are compared with the results of measurements on a Ching blue-and-white porcelain vase.

  3. Universitat popular al Cabanyal

    OpenAIRE

    Ribés Granell, Juan Miguel

    2012-01-01

    La intención es dotar al barrio de un gran espacio verde y de un edificio de interés para los vecinos que enriquezca al Cabanyal, ya que actualmente se encuentra en proceso de degradación. Se pretende desarrollar un proyecto que signifique una mejora en la predisposición del visitante, cubriendo sus necesidades. Al mismo tiempo, se busca crear un espacio arquitectónico que mejore la relación entre las actividades que incluye y su entorno. El proyecto está condicionado por cuatro aspectos fund...

  4. The solar element

    DEFF Research Database (Denmark)

    Kragh, Helge

    2009-01-01

    of the nineteenth century. In the modest form of a yellow spectral line known as D3, 'helium' was sometimes supposed to exist in the Sun's atmosphere, an idea which is traditionally ascribed to J. Norman Lockyer. Did Lockyer discover helium as a solar element? How was the suggestion received by chemists, physicists...... and astronomers in the period until the spring of 1895, when William Ramsay serendipitously found the gas in uranium minerals? The hypothetical element helium was fairly well known, yet Ramsay's discovery owed little or nothing to Lockyer's solar element. Indeed, for a brief while it was thought that the two...... elements might be different. The complex story of how helium became established as both a solar and terrestrial element involves precise observations as well as airy speculations. It is a story that is unique among the discovery histories of the chemical elements....

  5. The synthetic elements

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.C.

    1990-05-01

    Prior to 1940, the heaviest element known was uranium, discovered in 1789. Since that time the elements 93 through 109 have been synthesized and identified and the elements 43, 61, 85, and 87 which were missing form the periodic tables of the 1930's have been discovered. The techniques and problems involved in these discoveries and the placement of the transuranium elements in the periodic table will be discussed. The production and positive identification of elements heavier than Md (Z=101), which have very short half-lives and can only be produced an atom-at-a-time, are very difficult and there have been controversies concerning their discovery. Some of the new methods which have been developed and used in these studies will be described. The prospects for production of still heavier elements will be considered.

  6. The synthetic elements

    International Nuclear Information System (INIS)

    Hoffman, D.C.

    1990-05-01

    Prior to 1940, the heaviest element known was uranium, discovered in 1789. Since that time the elements 93 through 109 have been synthesized and identified and the elements 43, 61, 85, and 87 which were missing form the periodic tables of the 1930's have been discovered. The techniques and problems involved in these discoveries and the placement of the transuranium elements in the periodic table will be discussed. The production and positive identification of elements heavier than Md (Z=101), which have very short half-lives and can only be produced an atom-at-a-time, are very difficult and there have been controversies concerning their discovery. Some of the new methods which have been developed and used in these studies will be described. The prospects for production of still heavier elements will be considered

  7. Multi Elemental Study Using Prompt Gamma Technique

    International Nuclear Information System (INIS)

    Normanshah Dahing; Muhamad Samudi Yasir; Normanshah Dahing; Hanafi Ithnin; Mohd Fitri Abdul Rahman; Hearie Hassan

    2016-01-01

    In this study, principle of prompt gamma neutron activation analysis has been used as a technique to determine the elements in the sample. The system consists of collimated isotopic neutron source, Cf-252 with HPGe detector and Multichannel Analysis (MCA). Concrete with size of 10x10x10 cm 3 and 15x15x15 cm 3 were analysed as sample. When neutrons enter and interact with elements in the concrete, the neutron capture reaction will occur and produce characteristic prompt gamma ray of the elements. The preliminary result of this study demonstrate the major element in the concrete was determined such as Si, Mg, Ca, Al, Fe and H as well as others element, such as Cl by analysis the gamma ray lines respectively. The results obtained were compared with computer simulation, NAA and XRF as a part of reference and validation. The potential and the capability of neutron induced prompt gamma as tool for multi elemental analysis qualitatively to identify the elements present in the concrete sample discussed. (author)

  8. Fuel element loading system

    International Nuclear Information System (INIS)

    Arya, S.P; s.

    1978-01-01

    A nuclear fuel element loading system is described which conveys a plurality of fuel rods to longitudinal passages in fuel elements. Conveyor means successively position the fuel rods above the longitudinal passages in axial alignment therewith and adapter means guide the fuel rods from the conveyor means into the longitudinal passages. The fuel elements are vibrated to cause the fuel rods to fall into the longitudinal passages through the adapter means

  9. Elements in biological AMS

    International Nuclear Information System (INIS)

    Vogel, J.S.; McAninch, J.; Freeman, S.

    1996-08-01

    AMS (Accelerator Mass Spectrometry) provides high detection sensitivity for isotopes whose half-lives are between 10 years and 100 million years. 14 C is the most developed of such isotopes and is used in tracing natural and anthropogenic organic compounds in the Earth's biosphere. Thirty-three elements in the main periodic table and 17 lanthanides or actinides have long lived isotopes, providing potential tracers for research in elemental biochemistry. Overlap of biologically interesting heavy elements and possible AMS tracers is discussed

  10. Advanced Light Source (ALS)

    Data.gov (United States)

    Federal Laboratory Consortium — The Advanced Light Source (ALS), a world leader in soft x-ray science, generates light in the wavelengths needed for examining the atomic and electronic structure of...

  11. Taiwo et al (15)

    African Journals Online (AJOL)

    Timothy Ademakinwa

    geometric rise in preference for commercial aquaculture .... content, malondialdehyde level and lipid content of the muscle of the .... other researchers on the gilthead sea bream (Mnari et al., 2007), the .... 23, Orlando, Florida, USA, pp. 18–28.

  12. Okusanya et al (5)

    African Journals Online (AJOL)

    DELL

    rainfall and number of days with rain per month were obtained from Meteorological Institute, Oshodi, Lagos- ... Central and South America, Australia, West. Indies, Africa, (Orwa et al., 2009) and in Florida .... dominant forest tree species. In this ...

  13. Initial Symptoms of ALS

    Science.gov (United States)

    ... have trouble grasping a pen or lifting a coffee cup, while another person may experience a change ... Start your own fundraising event & help create a world without ALS Start an Event Site Map | Press ...

  14. ALS (Amyotrophic Lateral Sclerosis)

    Science.gov (United States)

    ... FDA) has approved the drugs riluzole (Rilutek) and edaravone (Radicava) to treat ALS. Riluzole is believed to ... reverse the damage already done to motor neurons. Edaravone has been shown to slow the decline in ...

  15. Amyotrophic Lateral Sclerosis (ALS)

    Science.gov (United States)

    ... found for ALS. However, the drugs riluzole and edaravone have approved by the Food and Drug Administration ( ... 2-3 months but does not relieve symptoms. Edaravone can slow the clinical decline in daily functioning ...

  16. Obuotor et al (16)

    African Journals Online (AJOL)

    DELL

    fractions and essential oils from the leaves of Eugenia uniflora were investigated on some multidrug resistant pathogens. ... et al., 1987), a reduction in blood pressure measured ..... from E. uniflora suggests high efficacy against this bacterium.

  17. Fakinle et al (11)

    African Journals Online (AJOL)

    DELL

    management issues; there is however a concern about air emissions from the ... poses risks to humans and animals through ... Nigeria have focused on cement industries. (Adejumo et al. ... based MCA which controls the sample holder and.

  18. Ogunyemi et al (17)

    African Journals Online (AJOL)

    DELL

    The results of physicochemical analysis revealed that the concentrations of ... scientific basis for regulating the discharge of potentially ... method for genotocity evaluation using Allium cepaand it ..... al., 2013). National agency for food and drug.

  19. Omotayo et al (4)

    African Journals Online (AJOL)

    DELL

    using biochemical technique and API 20E identification system. The isolates were .... sulphate, phosphate, ammonia and appearance. Heavy metals ... technique as described by Collee et al. (1989) was ..... enzymatic methods. Water Res. 36,.

  20. David et al (12)

    African Journals Online (AJOL)

    DELL

    larger mesophyll cells, xylem tissues, vascular bundles and bundle sheaths than other cultivars. Thus, larger ... mechanism to cope with drought stress. There was an ... where solar radiation is intense (Løe et al., 2007). Most ecological studies ...

  1. Cartas al editor

    Directory of Open Access Journals (Sweden)

    Facultad de Medicina Revista

    1995-10-01

    Full Text Available Con respecto al ensayo "Evaluación del aprendizaje en la educación superior" de la Dra. Análida Pinilla / Ciencia y conciencia en la medicina colombiana / Farmacovigilancia: Una necesidad urgente

  2. Analogs for transuranic elements

    International Nuclear Information System (INIS)

    Weimer, W.C.; Laul, J.C.; Kutt, J.C.

    1981-01-01

    A combined theoretical and experimental approach is being used to estimate the long-term environmental and biogeochemical behaviors of selected transuranic elements. The objective of this research is to estimate the effect that long-term (hundreds of years) environmental weathering has on the behavior of the transuranic elements americium and curium. This is achieved by investigating the actual behavior of naturally occurring rare earth elements, especially neodymium, that serve as transuranic analogs. Determination of the analog element behavior provides data that can be used to estimate the ultimate availability to man of transuranic materials released into the environment

  3. Chemistry of superheavy elements

    International Nuclear Information System (INIS)

    Schaedel, M.

    2012-01-01

    The chemistry of superheavy elements - or transactinides from their position in the Periodic Table - is summarized. After giving an overview over historical developments, nuclear aspects about synthesis of neutron-rich isotopes of these elements, produced in hot-fusion reactions, and their nuclear decay properties are briefly mentioned. Specific requirements to cope with the one-atom-at-a-time situation in automated chemical separations and recent developments in aqueous-phase and gas-phase chemistry are presented. Exciting, current developments, first applications, and future prospects of chemical separations behind physical recoil separators ('pre-separator') are discussed in detail. The status of our current knowledge about the chemistry of rutherfordium (Rf, element 104), dubnium (Db, element 105), seaborgium (Sg, element 106), bohrium (Bh, element 107), hassium (Hs, element 108), copernicium (Cn, element 112), and element 114 is discussed from an experimental point of view. Recent results are emphasized and compared with empirical extrapolations and with fully-relativistic theoretical calculations, especially also under the aspect of the architecture of the Periodic Table. (orig.)

  4. Kulturmorphologie als Zivilisationskritik

    DEFF Research Database (Denmark)

    Peters, Rikke Alberg

    2010-01-01

    Der Untergang des Abendlandes wird oft als dasjenige Werk betrachtet, das am tiefsten die national gefärbte Gegenüberstellung von Kultur und Zivilisation in der Zwischenkriegszeit geprägt und propagiert hat. Wie auch bei anderen Autoren der Konservativen Revolution, vor allem bei Thomas Mann und...... Arthur Moeller van den Bruck, tritt der Begriff ‚Kultur’ bei Spengler als normativer Wertbegriff auf, der im Kontrast zu einer degenerierten und seelenlosen Zivilisation steht....

  5. A influência do posicionamento ântero-posterior da alça T segmentada durante o movimento de retração inicial: uma avaliação pelo método dos elementos finitos The influence of the segmented T-loop anteroposterior position on the initial retraction movement: an evaluation by means of the finite element method

    Directory of Open Access Journals (Sweden)

    Raquel Silva Lotti

    2006-06-01

    Full Text Available OBJETIVO: avaliar por meio do MEF (Método dos elementos Finitos a influência do posicionamento no espaço inter-braquetes de uma alça T segmentada em aço inoxidável para retração do canino. METODOLOGIA: em cada posição da alça foi observado o tipo de movimento realizado pelas unidades de ancoragem e analisada a tensão no osso alveolar gerada pela mecânica. A alça foi confeccionada passiva, sem dobras de pré-ativação. O segmento posterior do lado esquerdo de uma mandíbula foi modelado, em conjunto com o canino, segundo pré-molar e primeiro molar permanente. Alterou-se o posicionamento da alça, obtendo um modelo em que esta se encontrou mais próxima ao canino, centralizada entre canino e molar e mais próxima ao molar. Apenas o deslocamento inicial destes dentes foi avaliado e as diferenças relativas entre o movimento destes foram comparadas em termos qualitativos. RESULTADOS E CONCLUSÕES: observou-se que o elemento dentário mais próximo à alça se deslocou em menor magnitude e com menor grau de inclinação. Em todos os modelos um componente de força extrusiva se fez presente, entretanto a magnitude deste foi menor para o dente mais afastado da alça. Relativa rotação foi encontrada resultando em deslocamentos para vestibular e lingual da coroa dos dentes e quanto mais afastado o dente se encontrou da alça, maior foi a tendência à rotação. O deslocamento relativo do canino foi maior que o do molar em todos os modelos. A análise da tensão em Von Mises no osso alveolar, demonstrou que esta se apresenta maior ao redor do canino e no modelo com a alça próxima ao molar.AIM: this study evaluated the effect produced by segmented stainless steel T-loop in different positions between a canine and a first lower molar on the force system by the FEM (Finite Element Method. METHODS: the type of movement of each anchorage units and the stress found in the alveolar bone were assessed in each T-loop positions. The loop was

  6. IBA analysis and corrosion resistance of TiAlPtN/TiAlN/TiAl multilayer films deposited over a CoCrMo using magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Canto, C.E., E-mail: carloscanto2012@yahoo.com.mx [Instituto de Física, Universidad Nacional Autónoma de México, Apartado Postal 20-364, 01000 México D.F. (Mexico); Andrade, E.; Lucio, O. de; Cruz, J.; Solís, C. [Instituto de Física, Universidad Nacional Autónoma de México, Apartado Postal 20-364, 01000 México D.F. (Mexico); Rocha, M.F. [ESIME-Z, IPN, U.P. ALM, Gustavo A. Madero, C.P. 07738 México D.F. (Mexico); Alemón, B. [Departamento de Ingeniería de Proyectos, CUCEI, Universidad de Guadalajara, J. Guadalupe Zuno 48, Los Belenes, Zapopan, Jalisco 45101 (Mexico); Tecnológico de Monterrey, Av. General Ramón Corona 2514, Col. Nuevo México, Zapopan, Jalisco 45201 (Mexico); Flores, M. [Departamento de Ingeniería de Proyectos, CUCEI, Universidad de Guadalajara, J. Guadalupe Zuno 48, Los Belenes, Zapopan, Jalisco 45101 (Mexico); Huegel, J.C. [Tecnológico de Monterrey, Av. General Ramón Corona 2514, Col. Nuevo México, Zapopan, Jalisco 45201 (Mexico)

    2016-03-15

    The corrosion resistance and the elemental profile of multilayer coatings of TiAlPtN/TiAlN/TiAl synthesized by Physical Vapor Deposition (PVD) reactive magnetron sputtering over a CoCrMo alloy substrate in 10 periods of 30 min each were analyzed and compared to those of the substrate alone and to that of a TiAlPtN single layer coating of the same thickness. The objective of the present work was to create multilayers with different amounts of Pt to enhance the corrosion resistance of a biomedical alloy of CoCrMo. Corrosion tests were performed using Simulated Body Fluid (SBF) using potentiodynamic polarization tests at typical body temperature. The elemental composition and thickness of the coatings were evaluated with the combination of two ion beam analysis (IBA) techniques: a Rutherford Backscattering Spectroscopy (RBS) with alpha beam and a Nuclear Reaction Analysis with a deuteron beam.

  7. IBA analysis and corrosion resistance of TiAlPtN/TiAlN/TiAl multilayer films deposited over a CoCrMo using magnetron sputtering

    International Nuclear Information System (INIS)

    Canto, C.E.; Andrade, E.; Lucio, O. de; Cruz, J.; Solís, C.; Rocha, M.F.; Alemón, B.; Flores, M.; Huegel, J.C.

    2016-01-01

    The corrosion resistance and the elemental profile of multilayer coatings of TiAlPtN/TiAlN/TiAl synthesized by Physical Vapor Deposition (PVD) reactive magnetron sputtering over a CoCrMo alloy substrate in 10 periods of 30 min each were analyzed and compared to those of the substrate alone and to that of a TiAlPtN single layer coating of the same thickness. The objective of the present work was to create multilayers with different amounts of Pt to enhance the corrosion resistance of a biomedical alloy of CoCrMo. Corrosion tests were performed using Simulated Body Fluid (SBF) using potentiodynamic polarization tests at typical body temperature. The elemental composition and thickness of the coatings were evaluated with the combination of two ion beam analysis (IBA) techniques: a Rutherford Backscattering Spectroscopy (RBS) with alpha beam and a Nuclear Reaction Analysis with a deuteron beam.

  8. The major and trace element chemistry of fish and lake water within ...

    African Journals Online (AJOL)

    2016-01-01

    Jan 1, 2016 ... and Abanoz (2011), De La Calle et al. (2012) and Sannac et al. (2012) of the same reference material. Dilution factors were cho- sen to include both major and trace elements in the same analy- ses, which implies that the method was not sensitive enough to analyse some elements at ultra-trace levels.

  9. Amadi et al (22)

    African Journals Online (AJOL)

    DELL

    that the soil is seriously polluted with mercury, cadmium and lead, moderately polluted ... interaction between soil and as well as water and ... essential to determine state of pollution in our ..... elements are contained in the minerals that make.

  10. Ogunbayo et al (18)

    African Journals Online (AJOL)

    DELL

    radioactive and other toxic elements like Pb from. 2+ the body. ... applications. Cisplatin ... solid-state properties that make them notable examples of adaptable functional organic materials. ... architecture on the process have been reported.

  11. Seagrass leaf element content

    NARCIS (Netherlands)

    Vonk, J.A.; Smulders, Fee O.H.; Christianen, Marjolijn J.A.; Govers, Laura L.

    2017-01-01

    Knowledge on the role of seagrass leaf elements and in particular micronutrients and their ranges is limited. We present a global database, consisting of 1126 unique leaf values for ten elements, obtained from literature and unpublished data, spanning 25 different seagrass species from 28 countries.

  12. Berkeley new element program

    International Nuclear Information System (INIS)

    Ghiorso, A.

    1975-09-01

    The work done with element 106 is reviewed, and a new experiment which bears on the properties of the isotope of mass 260 with atomic number 104 is discussed. It is noted that in the case of element 106 a link is demonstrated to the granddaughter as well as the daughter

  13. Elemental Food for Thought

    Science.gov (United States)

    Cady, Susan

    2005-01-01

    One of the first tasks students learn in chemistry is to pronounce and spell the names of elements and learn their corresponding chemical symbols. Repetitive oral recitation is commonly used to learn this information, but games and puzzles can make this task creative, variable, and fun. Elemental Food for Thought is a puzzlelike activity that…

  14. Nuclear fuel element

    International Nuclear Information System (INIS)

    Mogard, J.H.

    1977-01-01

    A nuclear fuel element is disclosed for use in power producing nuclear reactors, comprising a plurality of axially aligned ceramic cylindrical fuel bodies of the sintered type, and a cladding tube of metal or metal alloys, wherein said cladding tube on its cylindrical inner surface is provided with a plurality of slightly protruding spacing elements distributed over said inner surface

  15. Proceedings of transuranium elements

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The identification of the first synthetic elements was established by chemical evidence. Conclusive proof of the synthesis of the first artificial element, technetium, was published in 1937 by Perrier and Segre. An essential aspect of their achievement was the prediction of the chemical properties of element 43, which had been missing from the periodic table and which was expected to have properties similar to those of manganese and rhenium. The discovery of other artificial elements, astatine and francium, was facilitated in 1939-1940 by the prediction of their chemical properties. A little more than 50 years ago, in the spring of 1940, Edwin McMillan and Philip Abelson synthesized element 93, neptunium, and confirmed its uniqueness by chemical means. On August 30, 1940, Glenn Seaborg, Arthur Wahl, and the late Joseph Kennedy began their neutron irradiations of uranium nitrate hexahydrate. A few months later they synthesized element 94, later named plutonium, by observing the alpha particles emitted from uranium oxide targets that had been bombarded with deuterons. Shortly thereafter they proved that is was the second transuranium element by establishing its unique oxidation-reduction behavior. The symposium honored the scientists and engineers whose vision and dedication led to the discovery of the transuranium elements and to the understanding of the influence of 5f electrons on their electronic structure and bonding. This volume represents a record of papers presented at the symposium

  16. Reproduction of the RA reactor fuel element fabrication

    International Nuclear Information System (INIS)

    Novakovic, M.

    1961-12-01

    This document includes the following nine reports: Final report on task 08/12 - testing the Ra reactor fuel element; design concept for fabrication of RA reactor fuel element; investigation of the microstructure of the Ra reactor fuel element; Final report on task 08/13 producing binary alloys with Al, Mo, Zr, Nb and B additions; fabrication of U-Al alloy; final report on tasks 08/14 and 08/16; final report on task 08/32 diffusion bond between the fuel and the cladding of the Ra reactor fuel element; Final report on task 08/33, fabrication of the RA reactor fuel element cladding; and final report on task 08/36, diffusion of solid state metals [sr

  17. The assessment of essential elements in moringa oleifera

    International Nuclear Information System (INIS)

    Gyamfi, E.T.

    2010-01-01

    Moringa is known to contain elements that are essential to life. Major roles played by elements include enzyme activation, nerve impulse conduction, oxygen transport, immune functions. The two major groups of elements are major and minor elements (trace elements). Major elements such as Na, Ca, K, Mg and trace elements such as Fe, V, Zn, Cr, Cu, Cd, Co, Mn, Pb, Al, Br were determined using both NAA and AAS. The results revealed the presence of the following elements and anions: Al, Br, Ca, Cu, Cr, Fe, K, Mg, Mn, Na, V, Zn, PO 4 3- , NO 3 - . The elements Cd, Pb and Co were below the detection limits of the analytical technique. Risk assessment was performed to determine the risk of exposure to people who consume Moringa. Hazard Quotient (HQ) and Hazard Index (HI) were calculated to assess the risks associated with Moringa consumption. Since all the HQ and Hi values were less than one, it was concluded that no chronic risks was likely to occur from Moringa consumption. A significant test was performed to give a good interpretation of data. Further research is required to carry out the effectiveness of Moringa preparations in reducing the risks associated with diseases such as diabetes, hypertension. Air drying could be the preferred method for drying Moringa because it is hygienic, cheaper and has less effect on the elemental concentrations. (au)

  18. Mobilisation of toxic elements in the human respiratory system

    International Nuclear Information System (INIS)

    Pinheiro, T.; Alves, L.C.; Palhano, M.J.; Bugalho de Almeida, A.

    2001-01-01

    The fate of respired particles in the respiratory system is inferred through the chemical characterisation of individual particles at the tracheal and bronchial mucosas, and the accumulation of toxic elements in lung alveoli and lymph nodes. The particles and tissue elemental distributions were identified and characterised using micro-PIXE elemental mapping of thin frozen sections using the ITN Nuclear Microprobe facility. Significant particle deposits are found at the distal respiratory tract. Al, Si, Ti, V, Cr, Fe, Ni, Cu and Zn are elements detected at these accumulation areas. The elemental distributions in the different cellular environments of lymph nodes vary. The major compartments for Al, Si, Ti, Fe and Cr are the phagocytic cells and capsule of lymph nodes, while V and Ni are in the cortex and paracortex medullar areas which retain more than 70% of these two elements, suggesting high solubility of the latter in the cellular milieu. The elemental mobilisation from particles or deposits to surrounding tissues at the respiratory ducts evidences patterns of diffusion and removal that are different than those for elements in the respiratory tract. Mobilisation of elements such as V, Cr and Ni is more relevant at alveoli areas where gaseous exchange takes place. The apparent high solubility of V and Ni in the respiratory tract tissue points towards a deviation of the lymphatic system filtering efficiency for these elements when compared to others

  19. Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun, E-mail: forsjun@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); He, Xiaoman; Chen, Min; Hu, Huimin [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Zhang, Qiwu, E-mail: zhangqw@whut.edu.cn [School of Resources and Environmental Engineering, Wuhan University of Technology, Luoshi Road 122, Wuhan, Hubei 430070 (China); Liu, Xinzhong [College of Ecological Environment and Urban Construction, Fujian University of Technology, Fuzhou 350118 China (China)

    2017-04-15

    In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu{sub 2}(OH){sub 2}CO{sub 3}) and aluminum hydroxide (Al(OH){sub 3}) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

  20. Mechanochemical synthesis of Cu-Al and methyl orange intercalated Cu-Al layered double hydroxides

    International Nuclear Information System (INIS)

    Qu, Jun; He, Xiaoman; Chen, Min; Hu, Huimin; Zhang, Qiwu; Liu, Xinzhong

    2017-01-01

    In this study, a mechanochemical route to synthesize a Cu-Al layered double hydroxide (LDH) and a methyl orange (MO) intercalated one (MO-LDH) was introduced, in which basic cupric carbonate (Cu_2(OH)_2CO_3) and aluminum hydroxide (Al(OH)_3) with Cu/Al molar ratio at 2/1 was first dry ground for 2 h and then agitated in water or methyl orange solution for another 4 h to obtain the LDH and MO-LDH products without any heating operation. The prepared samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), Thermogravimetry (TG), Differential scanning calorimetry (DSC) and Scanning electron microscopy (SEM). The products showed high crystallinity phase of Cu-Al and MO intercalated Cu-Al LDH with no evident impurities, proving that the craft introduced here was facile and effective. The new idea can be applied in other fields to produce organic-inorganic composites. - Highlights: • A facile mechanochemical route to synthesize Cu-Al and MO intercalated Cu-Al LDH. • The products possesses high crystalline of LDH phase with no impure phases. • The dry milling process induces the element substitution between the raw materials. • The agitation operation helps the grain growth of LDH.

  1. Superstructure formation in PrNi_2Al_3 and ErPd_2Al_3

    International Nuclear Information System (INIS)

    Eustermann, Fabian; Hoffmann, Rolf-Dieter; Janka, Oliver; Oldenburg Univ.

    2017-01-01

    The intermetallic phase ErPd_2Al_3 was obtained by arc-melting of the elements and subsequent annealing for crystal growth. The sample was studied by X-ray diffraction on powders and single crystals. The structure of ErPd_2Al_3 was refined from X-ray diffraction data and revealed a superstructure of PrNi_2Al_3 - a CaCu_5 derivative (P6/m, a=1414.3(1), c=418.87(3) pm wR=0.0820, 1060 F"2 values, 48 variables). The same superstructure was subsequently found for PrNi_2Al_3 (P6/m, a=1407.87(4), c=406.19(2) pm, wR=0.0499, 904 F"2 values, 47 variables). In the crystal structure, the aluminium and transition metal atoms form a polyanionic network according to [T_2Al_3]"δ"-, while rare earth atoms fill cavities within the networks. They are coordinated by six transition metal and twelve aluminum atoms. In contrast to the PrNi_2Al_3 type structure reported so far, two crystallographic independent rare-earth sites are found of which one (1b) is shifted by 1/2 z, causing a distortion in the structure along with a recoloring of the T and Al atoms in the network.

  2. Coupled growth of Al-Al2Cu eutectics in Al-Cu-Ag alloys

    International Nuclear Information System (INIS)

    Hecht, U; Witusiewicz, V; Drevermann, A

    2012-01-01

    Coupled eutectic growth of Al and Al 2 Cu was investigated in univariant Al-Cu-Ag alloys during solidification with planar and cellular morphology. Experiments reveal the dynamic selection of small spacings, below the minimum undercooling spacing and show that distinct morphological features pertain to nearly isotropic or anisotropic Al-Al 2 Cu interfaces.

  3. Phase equilibria of the Mo-Al-Ho ternary system

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yitai; Chen, Xiaoxian; Liu, Hao [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Zhan, Yongzhong [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Laboratory of Processing for Non-ferrous Metal and Featured Materials; Guangxi Univ., Nanning (China). Center of Ecological Collaborative Innovation for Aluminum Industry

    2017-08-15

    Investigation into the reactions and phase equilibria of transition metal elements (i.e. Mo, Zr, Cr, V and Ti), Al and rare earths is academically and industrially important for the development of both refractory alloys and lightweight high-temperature materials. In this work, the equilibria of the Mo-Al-Ho ternary system at 773 K have been determined by using X-ray powder diffraction and scanning electron microscopy equipped with energy dispersive X-ray analysis. A new ternary phase Al{sub 4}Mo{sub 2}Ho has been found and the other ternary phase Al{sub 43}Mo{sub 4}Ho{sub 6} is observed. Ten binary phases in the Al-Mo and Al-Ho systems, including Al{sub 17}Mo{sub 4} rather than Al{sub 4}Mo, have been determined to exist at 773 K. The homogeneity ranges of AlMo{sub 3} and Al{sub 8}Mo{sub 3} phase are 7.5 at.% and 1 at.%, respectively. According to the phase-disappearing method, the maximum solubility of Al in Mo is about 16 at.%.

  4. Variation in ebmental quantification by X-ray fluorescence analysis in crystalline materials when applying pressure in sample preparation; Variacion de la cuantificacion elemental en el analisis por Fluorescencia de rayos X en materiales cristalinos al aplicar presion en la preparacion de muestras

    Energy Technology Data Exchange (ETDEWEB)

    Macias B, L.R.; Garcia C, R.M.; De Ita de la Torre, A.; Chavez R, A. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2000-07-01

    In this work making use of the diffraction and fluorescence techniques its were determined the presence of elements in a known compound ZrSiO{sub 4} under different pressure conditions. At preparing the samples it were applied different pressures from 1600 until 350 k N/m{sup 2} and it is detected the apparent variations in concentration in the Zr and Si elements. (Author)

  5. Pornographie als Metapher

    Directory of Open Access Journals (Sweden)

    Caroline Schubarth

    2010-03-01

    Full Text Available In diesem Artikel werden unterschiedliche metaphorische Verwendungen des Pornografiebegriffs und deren Implikationen untersucht. Während die Existenz von Pornografie der feministischen Anti-Porno-Bewegung als Erklärung für die anhaltende Diskriminierung von Frauen in westlichen Gesellschaften dient, nutzen rechtskonservative Kräfte den Pornografievorwurf als Rechtfertigung für die Zensur von als deviant empfundenen Identitäten und sexuellen Praktiken.This article examines different metaphorical uses of the term pornography and the resulting implications. While the existence of pornography for the feminist anti-porno movement serves as factor in the continuing discrimination of women in western societies, conservative powers on the right use the allegation of pornography as a justification for censorship of those identities and sexual practices deemed deviant.

  6. Mechanism of serrated flow in binary Al-Li alloys

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, S.; Pink, E. [Austrian Academy of Sciences, Leoben (Austria). Erich-Schmid-Inst. of Solid State Physics; Krol, J. [Polish Academy of Sciences, Krakow (Poland). Alexander-Krupkowski-Inst. of Metallurgy and Materials Science

    1996-09-15

    The work on serrated flow in Al-Li alloys has given rise to a controversy--whether serrations in these alloys are caused by lithium atoms in solid solution or by {delta}{prime}(Al{sub 3}Li)-precipitates. This controversy calls for further work to clarify the mechanism of serrated flow in the Al-Li alloys. Kumar and McShane have shown that in an Al-2.5Li-2Mg-0.14Zr alloy, non-shearable {delta}{prime}-precipitates, which are obtained in the under-aged and peak-aged conditions, might directly initiate serrated flow. However, the latter result was ambiguous because of the presence of other alloying elements, and the need to work on a binary Al-Li alloy was emphasized. The present work discusses the results from the binary Al-Li alloys.

  7. Bioaccumulation of trace elements by Avicennia marina

    Directory of Open Access Journals (Sweden)

    Kandasamy Kathiresan

    2014-11-01

    Full Text Available Objective: To analyze the concentrations of 12 micro-nutrients (Al, B, Cd, Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, and Zn in different plant parts of Avicennia marina and its rhizosphere soil of the south east coast of India. Methods: The samples were acid digested, then analyzed by using inductively coupled plasma system (ICP-Optical Emission Spectrophotometer. Results: Levels of metals were found in the decreasing order: Cd>Co>Ni>Pb>B >Cr>Zn>Mg>Mn>Cu>Fe>Al. The soil held more levels of metals than plant parts, but within the permissible limits of concentration. Bark and root accumulated higher levels of trace elements in a magnitude of 10-80 folds than other plant parts. The overall bioaccumulation factor in the sampling sites of Vellar, Pichavaram and Cuddalore was 2.88, 1.42 0.47 respectively. Essential elements accumulate high in mature mangroves forest while non-essential elements accumulate high in the industrially polluted mangroves. Conclusions: The ratio between essential and non-essential elements was found higher in young mangrove forest than that in mature mangrove forest and polluted mangrove areas. Thus, the ratio of accumulation can be used as an index of the growth and pollution status of mangroves.

  8. Instrumental trace element analysis of California market milk

    International Nuclear Information System (INIS)

    Ragaini, R.C.; Langhorst, A.L.; Ralston, H.R.; Heft, R.

    1975-01-01

    Trace element analysis for 15 elements (Zn, Na, Br, Rb, Sr, Mg, Al, Ca, Cl, I, K, Fe, Co, Se, Cs) was carried out on 32 samples of California market milk and 6 samples of Colorado milk in a pilot study of toxic and nutrient trace elements in the soil-forage-cow-milk food chain. The techniques of instrumental neutron activation analysis and x-ray fluorescence analysis are described. Sample collection, preparation, analysis, and data reduction procedures are discussed. The mean values and variations of trace element concentrations in milk are compared to data from other studies. (U.S.)

  9. Status of U3Si2-Al fuel development in China

    International Nuclear Information System (INIS)

    Sun Rongxian; Huang Dechen; Yin Changgeng; Zhang Qindi; He Fengqi; Li Shuhua; Xiang Xingbi; Zhang Zhiyi; Wang Zhaoyue

    1995-01-01

    On the basis of the research and development work, a production line of U 3 Si 2 -Al dispersion fuel elements has been established and tens of the fuel elements have been produced. A lot of technical improvements and reliable inspection system ensure that all technical performance of the fuel elements meet International standards. (author)

  10. Discovery of element 112

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, S. [GSI, Darmstadt (Germany)

    1996-12-31

    The new elements 110, 111, and 112 were synthesized and unambiguously identified in experiments at SHIP. Due to strong shell effects the dominant decay mode is not fission, but emission of alpha particles. Theoretical investigations predict that maximum shell effects should exist in nuclei near proton number 114 and neutron number 184. Measurements give hope that isotopes of element 114 close to the island of spherical Superheavy Elements could be produced by fusion reactions using {sup 118}Pb as target. systematic studies of the reaction cross-sections indicate that transfer of nucleons is the important process to initiate the fusion.

  11. Nuclear fuel element

    International Nuclear Information System (INIS)

    Grossman, L.N.; Levin, H.A.

    1975-01-01

    A nuclear fuel element has disposed therein an alloy having the essential components of nickel, titanium and zirconium, and the alloy reacts with water, water vapor and reactive gases at reactor ambient temperatures. The alloy is disposed in the plenum of the fuel element in the form of particles in a hollow gas permeable container having a multiplicity of openings of size smallr than the size of the particles. The container is preferably held in the spring in the plenum of the fuel element. (E.C.B.)

  12. Elemental diffusion in stars

    International Nuclear Information System (INIS)

    Michaud, Georges; Montmerle, Thierry

    1977-01-01

    This paper is dealing with the origin of the elements in the universe. The scheme of nucleosynthesis is kept to explain the stellar generation of helium, carbon, etc... from the initial hydrogen; but a nonlinear theory is then elaborated to account for the anomalous abundances which were observed. The chemical elements would diffuse throughout the outer layers of a star under the action of the opposite forces of gravitation and radiation. This theory, with completing the nucleosynthesis, would contribute to give a consistent scheme of the elemental origin and abundances [fr

  13. MOSQUE ARCHITECTURE AS A SUSTAINABLE BUILDING IN URBAN (Case Study: Al Markas Al Islamic Mosque Makassar

    Directory of Open Access Journals (Sweden)

    Imriyanti Imriyanti

    2014-02-01

    Full Text Available Abstract Mosque Architecture is a part of Islamic architecture. Mosque should be fused with elements of nature because its function as a place to pray to God who created the universe. Al Markas Al Islamic Makassar mosque is used as a center of Islamic aspirations of the people and the government to accommodate all the activities of moslems in Makassar. Through this function, the provision of Al Markas Al Islamic mosque began from the desire of Islamic societies in Makassar, which wants the Islamic center to be equipped with facilities and infrastructure as well as architectural, monumental buildings and structures that can be last for hundreds of years (continuous, blend with the environment, and also can be used by the public. Having regard to the function of a mosque especially at the Al Markas Al Islamic Makassar mosque, then the problem that arise is how the Al Markas Al Islamic mosque can be survived/sustainable  in order  to function  as a place  of worship  and  as a center  of Islam.  This research  is a descriptive qualitative research that is trying to generate data in the form of systematic and accurate picture of the object of study. The sustaiprophetlity  of Al Markas AL Islamic mosque can be known through the concept of Islam  in accordance with the view of Islam as well as the sustaiprophetlity of the buildings that seen in the spatial pattern of the mosque, appearance, natural lighting, natural ventilation, and user behavior of the mosque. Keywords: mosque architecture, sustaiprophetlity, view of Islam     Abstrak Arsitektur masjid merupakan bagian dari arsitektur Islam. Bangunan masjid sebaiknya dapat menyatu dengan unsur alam karena masjid difungsikan sebagai wadah dalam bersujud/sembahyang  kepada Allah SWT yang menciptakan alam semesta ini. Masjid Al Markas Al Islamic Makassar merupakan kompleks kegiatan Islam yang digunakan sebagai pusat aspirasi masyarakat  dan pemerintahan  yang dapat menampung

  14. Bridge element deterioration rates.

    Science.gov (United States)

    2008-10-01

    This report describes the development of bridge element deterioration rates using the NYSDOT : bridge inspection database using Markov chains and Weibull-based approaches. It is observed : that Weibull-based approach is more reliable for developing b...

  15. 2. Transuranic elements

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    Methods of sample collection, sample storage, sample procedures and radioanalytical procedures for transuranic elements in marine environment are reviewed and recommended. Alpha spectrometry and scintillation techniques are used for measurement of isotopic content. Separation processes for samples are described

  16. Heavy element research

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    Heavy element research activities in metallurgy and ceramics during 1976 at Lawrence Berkeley Laboratory are reviewed. Topics include: microstructure, properties and alloy design; ceramic alloy program; high resolution and high voltage electron microscopy; and powder metallurgy

  17. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E.D.

    1981-01-01

    An array of rods comprising zirconium alloy sheathed nuclear fuel pellets assembled to form a fuel element for a pressurised water reactor is claimed. The helium gas pressure within each rod differs substantially from that of its closest neighbours

  18. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E.D.

    1984-01-01

    The fuel elements for a pressurised water reactor comprise arrays of rods of zirconium alloy sheathed nuclear fuel pellets. The helium gas pressure within each rod differs substantially from that of its closest neighbours

  19. Transposable elements in cancer.

    Science.gov (United States)

    Burns, Kathleen H

    2017-07-01

    Transposable elements give rise to interspersed repeats, sequences that comprise most of our genomes. These mobile DNAs have been historically underappreciated - both because they have been presumed to be unimportant, and because their high copy number and variability pose unique technical challenges. Neither impediment now seems steadfast. Interest in the human mobilome has never been greater, and methods enabling its study are maturing at a fast pace. This Review describes the activity of transposable elements in human cancers, particularly long interspersed element-1 (LINE-1). LINE-1 sequences are self-propagating, protein-coding retrotransposons, and their activity results in somatically acquired insertions in cancer genomes. Altered expression of transposable elements and animation of genomic LINE-1 sequences appear to be hallmarks of cancer, and can be responsible for driving mutations in tumorigenesis.

  20. Divergent picornavirus IRES elements

    DEFF Research Database (Denmark)

    Belsham, Graham

    2009-01-01

    Internal ribosome entry site (IRES) elements were first identified about 20 years ago within the 5' untranslated region of picornavirus RNAs. They direct a cap-independent mechanism of translation initiation on the viral RNA. Within the picornavirus family it is now known that there are four...... classes of IRES element which vary in size (450-270nt), they also have different, complex, secondary structures and distinct requirements for cellular proteins to allow them to function. This review describes the features of each class of picornavirus IRES element but focuses on the characteristics...... of the most recently described group, initially identified within the porcine teschovirus-1 RNA, which has strong similarities to the IRES elements from within the genomes of hepatitis C virus and the pestiviruses which are members of the flavivirus family. The selection of the initiation codon...

  1. BERKELEY: ALS ring

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1993-06-15

    Everybody at Lawrence Berkeley Laboratory's Center for Beam Physics is pleased with the rapid progress in commissioning LBL's Advanced Light Source (ALS) electron storage ring, the foundation for this third-generation synchrotron radiation facility. Designed for a maximum current of 400 mA, the ALS storage ring reached 407 mA just 24 days after storing the first beam on 16 March. ALS construction as a US Department of Energy (DOE) national user facility to provide high-brightness vacuum ultra-violet and soft x-ray radiation began in October 1987. One technical requirement marking project completion was to accumulate a 50-mA current in the storage ring. The ALS passed this milestone on 24 March, a week ahead of the official deadline. Once injected, the electron beam decays quasi-exponentially primarily because of interactions with residual gas molecules in the storage-ring vacuum chamber. Eventually, when the pressure in the vacuum chamber with beam decreases toward the expected operating level of 1 nano Torr, it will only be necessary to refill the storage ring at intervals of four to eight hours. At present the vacuum is improving rapidly as surfaces are irradiated (scrubbed) by the synchrotron radiation itself. At 100 mA, beam lifetime was about one hour (9 April)

  2. Alimba et al (5)

    African Journals Online (AJOL)

    USER

    There was significant (p<0.05) increase in erythrocytes, haemoglobin ... for its anti-hemorrhoid and anti-inflammatory properties (Afolabi et al., 2008), ... genome instability which may lead to genetic related diseases ... membrane, behavioral pattern, morbidity and mortality. ..... extracts of Phyllanthus amarus in mice and rats.

  3. Taiwo et al (8)

    African Journals Online (AJOL)

    DELL

    Ife Journal of Science. (2016) vol. 18, no. 4. SPATIAL ... Ogun State. On the contrary, published work in some parts of Nigeria had ..... Prevalence among. Age Group (%). Cause of Infection. (%). Adeoye et al.,. 2007. Lagos. Kato-Katz. A. lumbricoides =29.7. Hookworm = 0.7. T. Trichiura = 18.4. S. stercoralis =0.3. Total =49.1.

  4. Rossie et al

    African Journals Online (AJOL)

    PUBLICATIONS1

    ing onto the torso for bike riders (Blocken et al., 2013) or it might ... designing new vehicles as well as for drawing up specific training ... These models were chosen because they repre- ..... muscles is relevant since the bio-mechanical workload ...

  5. aboagye et al.2

    African Journals Online (AJOL)

    PUBLICATIONS1

    14 Aboagye et al. wide variety of birds, including chickens, by piercing the quills of feathers and gnawing the epidermis. In doing so, they can spread disease and lower .... evolution. Oikos, 97: 223-228. Nordenfors, H. and Chirico, J. (2001). Evalua- tion of a sampling trap for Dermanyssus gal- linae (Acari: Dermanyssidae).

  6. Fadimu et al

    African Journals Online (AJOL)

    coconut water has the potential to increase growth and nutritional value of S. mombin(Linn.) so that S. mombin ... of plant growth and development, including seed maturation and ... et al., 2000). Auxins are primary regulators of plant form while ...

  7. Bello et al (9)

    African Journals Online (AJOL)

    Timade VENTURE

    family Solanaceae and it is one of the largest and ... al.,2004). The taxonomy of this important genus is of ... importance of numerical taxonomic method in ..... SME. SAE. SAM. SNI. SER. SWR. SMA. SGI. -6.4. -4.8. -3.2. -1.6. 0. 1.6. 3.2. 4.8.

  8. Iraq and Al Qaeda

    National Research Council Canada - National Science Library

    Katzman, Kenneth

    2008-01-01

    .... The Administration assertions were derived from U.S. intelligence showing a pattern of contacts with Al Qaeda when its key founder, Osama bin Laden, was based in Sudan in the early to mid-1990s and continuing after he relocated to Afghanistan in 1996...

  9. Iraq and Al Qaeda

    National Research Council Canada - National Science Library

    Katzman, Kenneth

    2007-01-01

    .... The Administration's assertions were derived from U.S. intelligence showing a pattern of contacts with Al Qaeda when its founder, Osama bin Laden, was based in Sudan in the early to mid-1990s and continuing after he relocated to Afghanistan in 1996...

  10. Ojo et al (2)

    African Journals Online (AJOL)

    DELL

    network geometry hence control how the samples' ... generate different permeability curves from wire- ... occupy in the reservoir pore system (McPhee et. ..... Fig.3. Poroperm cross-plot for a homogenous reservoir. Ojo et al.: Rock Type Based ...

  11. Agwu et al (6)

    African Journals Online (AJOL)

    DELL

    Enterobacteriaceae, the bacteria Escherichia coli is regarded as non-halophilic, and cannot tolerate high salt concentrations (Abdulkarim et al., 2009). Nevertheless, some strains of E. coli are halo- tolerant and survive in high salt concentrations. The ability to demonstrate such high osmotic pressure is possibly due to the ...

  12. Dichtung als Erfahrungsmetaphysik

    DEFF Research Database (Denmark)

    Magnusson, Gisli

    Rilkeforskning. Fordi Rilke ikke – uden at gøre vold mod hans værk – kan fortolkes ud fra et traditionelt religiøst verdensbillede, har man fortolket ham som en antimetafysisk mo­dernist. Afhandlingen Dichtung als Erfahrungsmetaphysik. Esoterische und okkultistische Modernität bei R. M. Rilke argumenterer for...

  13. Nucleosynthesis of 26Al

    International Nuclear Information System (INIS)

    Casse, M.

    1986-07-01

    A burst of interest has followed the discovery in the galactic plane of the 1.8 MeV gamma line attached to the decay of 26 Al. We discuss the relative merits of supernovae, novae, massive and supermassive mass-losing stars as potential sources of this expressive isotope

  14. Njukeng et al. + DOI

    African Journals Online (AJOL)

    confo

    3 Institute of Agricultural Research and Development (IRAD), Bambui, North West Province, Cameroon. ... Potato (Solanum tuberosum L.) is an important cash-food crop, which is widely ... production in Africa nearly tripled over the past 35 years ... Njukeng et al, Prevalence of Viruses in Potato Seed Tubers in the North West ...

  15. Comentarios al Salto Social

    Directory of Open Access Journals (Sweden)

    Facultad de Ciencias Económicas

    1995-06-01

    Full Text Available 1. El Plan considera que la política social es un componente central de la estrategia macroeconómica. A diferencia de la administración Gaviria, lo social ha dejado de ser un asunto marginal, es consustancial al desarrollo y, por tanto, se le confiere una dimensión cualitativamente diferente.

  16. Hamid et al (24)

    African Journals Online (AJOL)

    USER

    acne, and eye problems (Diaz-Bolio, 1975). Cnidoscolus aconitifolius roots and leaves have been taken as a laxative, diuretic, circulation stimulant, to increase digestion, stimulant for lactation, and to harden the fingernails (Rowe, 1994; Kuti, and. Torres, 1996). Oyagbemi et al., (2011) reported the proximate analysis and ...

  17. Esuuman et al (17)

    African Journals Online (AJOL)

    big timmy

    ether (Sathe et al., 2002). Various extraction conditions such as pH, solvent types (NaOH, NaCl or Ethanol), solvent concentration, extraction time, solvent/flour ratio, may affect the final properties of the extracted protein. When many factors and interactions affect desired responses in a certain process design, Response.

  18. BERKELEY: ALS ring

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Everybody at Lawrence Berkeley Laboratory's Center for Beam Physics is pleased with the rapid progress in commissioning LBL's Advanced Light Source (ALS) electron storage ring, the foundation for this third-generation synchrotron radiation facility. Designed for a maximum current of 400 mA, the ALS storage ring reached 407 mA just 24 days after storing the first beam on 16 March. ALS construction as a US Department of Energy (DOE) national user facility to provide high-brightness vacuum ultra-violet and soft x-ray radiation began in October 1987. One technical requirement marking project completion was to accumulate a 50-mA current in the storage ring. The ALS passed this milestone on 24 March, a week ahead of the official deadline. Once injected, the electron beam decays quasi-exponentially primarily because of interactions with residual gas molecules in the storage-ring vacuum chamber. Eventually, when the pressure in the vacuum chamber with beam decreases toward the expected operating level of 1 nano Torr, it will only be necessary to refill the storage ring at intervals of four to eight hours. At present the vacuum is improving rapidly as surfaces are irradiated (scrubbed) by the synchrotron radiation itself. At 100 mA, beam lifetime was about one hour (9 April)

  19. Proton irradiation studies on Al and Al5083 alloy

    Science.gov (United States)

    Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

    2017-10-01

    The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

  20. Novel porcine repetitive elements

    Directory of Open Access Journals (Sweden)

    Nonneman Dan J

    2006-12-01

    Full Text Available Abstract Background Repetitive elements comprise ~45% of mammalian genomes and are increasingly known to impact genomic function by contributing to the genomic architecture, by direct regulation of gene expression and by affecting genomic size, diversity and evolution. The ubiquity and increasingly understood importance of repetitive elements contribute to the need to identify and annotate them. We set out to identify previously uncharacterized repetitive DNA in the porcine genome. Once found, we characterized the prevalence of these repeats in other mammals. Results We discovered 27 repetitive elements in 220 BACs covering 1% of the porcine genome (Comparative Vertebrate Sequencing Initiative; CVSI. These repeats varied in length from 55 to 1059 nucleotides. To estimate copy numbers, we went to an independent source of data, the BAC-end sequences (Wellcome Trust Sanger Institute, covering approximately 15% of the porcine genome. Copy numbers in BAC-ends were less than one hundred for 6 repeat elements, between 100 and 1000 for 16 and between 1,000 and 10,000 for 5. Several of the repeat elements were found in the bovine genome and we have identified two with orthologous sites, indicating that these elements were present in their common ancestor. None of the repeat elements were found in primate, rodent or dog genomes. We were unable to identify any of the replication machinery common to active transposable elements in these newly identified repeats. Conclusion The presence of both orthologous and non-orthologous sites indicates that some sites existed prior to speciation and some were generated later. The identification of low to moderate copy number repetitive DNA that is specific to artiodactyls will be critical in the assembly of livestock genomes and studies of comparative genomics.

  1. Fuel element store

    International Nuclear Information System (INIS)

    Wieser, R.

    1987-01-01

    The spherical fuel elements are stored dry in cans. The cans themselves are stacked in parallel storage shafts, which are combined into a rectangular storage space. The storage space is made earthquake-proof by surrounding it with concrete. It consists of a ceiling assembled from several steel parts, which is connected to the floor by support elements. A cooling air ventilation station supplies the individual storage shaft and therefore the cans with cooling air via incoming and outgoing pipes. (DG) [de

  2. Intrusion detection system elements

    International Nuclear Information System (INIS)

    Eaton, M.J.; Mangan, D.L.

    1980-09-01

    This report highlights elements required for an intrusion detection system and discusses problems which can be encountered in attempting to make the elements effective. Topics discussed include: sensors, both for exterior detection and interior detection; alarm assessment systems, with the discussion focused on video assessment; and alarm reporting systems, including alarm communication systems and dislay/console considerations. Guidance on careful planning and design of a new or to-be-improved system is presented

  3. Structural elements design manual

    CERN Document Server

    Draycott, Trevor

    2012-01-01

    Gives clear explanations of the logical design sequence for structural elements. The Structural Engineer says: `The book explains, in simple terms, and with many examples, Code of Practice methods for sizing structural sections in timber, concrete,masonry and steel. It is the combination into one book of section sizing methods in each of these materials that makes this text so useful....Students will find this an essential support text to the Codes of Practice in their study of element sizing'.

  4. Atoms, molecules & elements

    CERN Document Server

    Graybill, George

    2007-01-01

    Young scientists will be thrilled to explore the invisible world of atoms, molecules and elements. Our resource provides ready-to-use information and activities for remedial students using simplified language and vocabulary. Students will label each part of the atom, learn what compounds are, and explore the patterns in the periodic table of elements to find calcium (Ca), chlorine (Cl), and helium (He) through hands-on activities.

  5. Nuclear fuel element

    International Nuclear Information System (INIS)

    Penrose, R.T.; Thompson, J.R.

    1976-01-01

    A method of protecting the cladding of a nuclear fuel element from internal attack and a nuclear fuel element for use in the core of a nuclear reactor are disclosed. The nuclear fuel element has disposed therein an additive of a barium-containing material and the barium-containing material collects reactive gases through chemical reaction or adsorption at temperatures ranging from room temperature up to fuel element plenum temperatures. The additive is located in the plenum of the fuel element and preferably in the form of particles in a hollow container having a multiplicity of gas permeable openings in one portion of the container with the openings being of a size smaller than the size of the particles. The openings permit gases and liquids entering the plenum to contact the particles. The additive is comprised of elemental barium or a barium alloy containing one or more metals in addition to barium such as aluminum, zirconium, nickel, titanium and combinations thereof. 6 claims, 3 drawing figures

  6. Trace elements record complex histories in diogenites

    Science.gov (United States)

    Balta, J. B.; Beck, A. W.; McSween, H. Y.

    2012-12-01

    Diogenite meteorites are cumulate rocks composed mostly of orthopyroxene and chemically linked to eucrites (basaltic) and howardites (brecciated mixtures of diogenites and eucrites). Together, they represent the largest single family of achondrite meteorites delivered to Earth, and have been spectrally linked to the asteroid 4 Vesta, the largest remaining basaltic protoplanet. However, this spectral link is non-unique as many basaltic asteroids likely formed and were destroyed in the early solar system. Recent work suggested that Vesta may be an unlikely parent body for the diogenites based on correlations between trace elements and short-lived isotope decay products, which would be unlikely to survive on a body as large as Vesta due to its long cooling history [1]. Recent analyses of terrestrial and martian olivines have demonstrated that trace element spatial distributions can preserve evidence of their crystallization history even when major elements have been homogenized [2]. We have mapped minor elements including Cr, Al, and Ti in seemingly homogeneous diogenite orthopyroxenes and found a variety of previously unobserved textures. The pyroxenes in one sample (GRA 98108) are seemingly large grains of variable shapes and sizes, but the trace elements reveal internal grain boundaries between roughly-equal sized original subgrains, with equilibrated metamorphic triple junctions between them and trace element depletions at the boundaries. These trends suggest extraction of trace elements by a magma along those relict grain boundaries during a reheating event. Two other samples show evidence of fracturing and annealing, with trace element mobility within grains. One sample appears to have remained a closed system during annealing (MET 01084), while the other has interacted with a fluid or magma to move elements along annealed cracks (LEW 88679). These relict features establish that the history of diogenite pyroxenes is more complex than their homogeneous major

  7. Major and trace elements in coal bottom ash at different oxy coal combustion conditions

    CSIR Research Space (South Africa)

    Oboirien, BO

    2014-09-01

    Full Text Available This paper presents a detailed study on the effect of temperature on the concentration of 27 major and trace elements in bottom ash generated from oxy fuel-combustion. The major elements are Na, Mg, Al, K, Ca and Fe and the minor and trace elements...

  8. Synthesis of Ti3AlC2 by spark plasma sintering of mechanically milled 3Ti/xAl/2C powder mixtures

    International Nuclear Information System (INIS)

    Yang Chen; Jin Songzhe; Liang Baoyan; Liu Guojun; Duan Lianfeng; Jia Shusheng

    2009-01-01

    Elemental powders of Ti, Al and C were mechanically milled as starting materials for the fabrication of ternary carbide Ti 3 AlC 2 by spark plasma sintering (SPS) technique. The effect of Al content in the starting materials on the Ti 3 AlC 2 synthesis was investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to determine the phase identification and observe the microstructure of the synthesized samples. With increasing proper Al content, it was found that the purity of Ti 3 AlC 2 increased and the sintering temperature reduced. The dense and high-purity Ti 3 AlC 2 could be successfully fabricated from 3Ti/1.2Al/2C powders at a lower sintering temperature of 1050 deg. C, holding for 10 min. In addition, the reaction path for the formation of Ti 3 AlC 2 in the present study was proposed

  9. Adebayo et al (6)

    African Journals Online (AJOL)

    Timade VENTURE

    The least nitrogen solubility of defatted kariya flour occurred at pH 4, hence the iso-electric pH ... Until recently, soy protein has been the main .... digestion, and F = protein content of DKKF after digestion. .... macro and micro mineral elements.

  10. Neutron activation analysis of trace metallic elements eluted from molecular sieves in the dehydration process of safflower oil

    Energy Technology Data Exchange (ETDEWEB)

    Takasago, Masahisa; Kobayashi, Koichi; Taru, Yasunori; Takaoka, Kyo (Musashi Inst. of Tech., Tokyo (Japan))

    1992-11-01

    Dissolved water in safflower oil affects the autoxidation of this oil significantly. Molecular sieves were used to remove the dissolved water from the oil. This method is much simpler than that of distillation, and dissolved water can be removed to the same extent as that by distillation. But, due to the elution of many kinds of trace metallic elements in the oil dehydrated with molecular sieves, these elements were analyzed by neutron activation analysis. For a data comparison trace amounts of metallic elements in the oil dehydrated by distillation were also analyzed. Since the intensity of the [gamma] ray-photoelectric peak of nuclide [sup 28]Al was largest among the detected elements, this element was analyzed quantitatively and the other elements qualitatively. In safflower oil dehydrated with molecular sieves, 14 kinds of the elements (I, Br, Al, Mg, Si, V, Cl, Nd, Ta, Cr, Sb, Cs, Co, Na) were detected. Also, I, Br, Cl, Cr, Ta, Sb, and Al elements were detected in the oil dehydrated by distillation. The intensity of the photoelectric peak of nuclide except [sup 28]Al was essentially the same as that in the oil dehydrated by distillation, but the intensity of [sup 28]Al in the oil with molecular sieves was about 28 times stronger than that in distillation oil. In the molecular sieves, 19 impure elements in addition to the original constituents (Na, K, Al, si, O) were detected. It was Al, Na, Si, Nd, Cs, and Co along with impure elements may possibly have been eluted in the oil. Al element in safflower oil dehydrated with molecular sieves was analyzed quantitatively. 0.91 ppm of Al was detected in safflower oil. The eluted amount of Al in safflower oil dehydrated by distillation was 0.032 ppm. A larger amount of Al element was thus eluted into the oil dehydrated with molecular sieves than by distillation. (author).

  11. Neutron activation analysis of trace metallic elements eluted from molecular sieves in the dehydration process of safflower oil

    International Nuclear Information System (INIS)

    Takasago, Masahisa; Kobayashi, Koichi; Taru, Yasunori; Takaoka, Kyo

    1992-01-01

    Dissolved water in safflower oil affects the autoxidation of this oil significantly. Molecular sieves were used to remove the dissolved water from the oil. This method is much simpler than that of distillation, and dissolved water can be removed to the same extent as that by distillation. But, due to the elution of many kinds of trace metallic elements in the oil dehydrated with molecular sieves, these elements were analyzed by neutron activation analysis. For a data comparison trace amounts of metallic elements in the oil dehydrated by distillation were also analyzed. Since the intensity of the γ ray-photoelectric peak of nuclide 28 Al was largest among the detected elements, this element was analyzed quantitatively and the other elements qualitatively. In safflower oil dehydrated with molecular sieves, 14 kinds of the elements (I, Br, Al, Mg, Si, V, Cl, Nd, Ta, Cr, Sb, Cs, Co, Na) were detected. Also, I, Br, Cl, Cr, Ta, Sb, and Al elements were detected in the oil dehydrated by distillation. The intensity of the photoelectric peak of nuclide except 28 Al was essentially the same as that in the oil dehydrated by distillation, but the intensity of 28 Al in the oil with molecular sieves was about 28 times stronger than that in distillation oil. In the molecular sieves, 19 impure elements in addition to the original constituents (Na, K, Al, si, O) were detected. It was Al, Na, Si, Nd, Cs, and Co along with impure elements may possibly have been eluted in the oil. Al element in safflower oil dehydrated with molecular sieves was analyzed quantitatively. 0.91 ppm of Al was detected in safflower oil. The eluted amount of Al in safflower oil dehydrated by distillation was 0.032 ppm. A larger amount of Al element was thus eluted into the oil dehydrated with molecular sieves than by distillation. (author)

  12. Determination of Fe and Al contamination by NAA at preparation of traditional Mexican food

    International Nuclear Information System (INIS)

    Arriola, S.H.; Cruz, M.M.

    2007-01-01

    A study was carried out using NAA to measure the concentration of Al and Fe leached from kitchen ware into some popular Mexican sauces and juices. These elements were measured in red and green hot sauces cooked in Fe, Al and clay pans compared to a stainless steel pan. Similarly Al was measured in orange and grapefruit juices obtained using an Al extractor compared to a plastic one. (author)

  13. Nanoindentation studies of ex situ AlN/Al metal matrix nanocomposites

    International Nuclear Information System (INIS)

    Fale, Sandeep; Likhite, Ajay; Bhatt, Jatin

    2014-01-01

    Highlights: • Formation of in-situ phases nucleated on AlN particles strengthens the matrix. • Formation of in-situ phases increases with AlN content in nanocomposites. • Stronger in-situ phases results in increased hardness and modulus of elasticity. - Abstract: Nanocrystalline Aluminium nitride (AlN) powder is dispersed in different weight ratio in Aluminum matrix to fabricate metal matrix nanocomposite (MMNC) using ex situ melt metallurgy process. The synthesized Al–AlN nanocomposites are studied for phase analysis using high resolution scanning electron microscopy (FEG-SEM) and for hardness behavior using microindentation and nanoindentation tests. Quantitative analysis of the oxide phases is calculated from thermodynamic data and mass balance equation using elemental data obtained from energy dispersive spectroscopy (EDS) results. Role of oxide phases in association with AlN particles is investigated to understand the mechanical behavior of composites using nanoindentation tester. Load–displacement profile obtained from nanoindentation test reveals distribution of oxide phases along with AlN particle and their effect on indent penetration

  14. Factores asociados al bajo peso al nacer

    Directory of Open Access Journals (Sweden)

    Georgina J Peraza Roque

    2001-10-01

    Full Text Available El bajo peso al nacer (BPN ha constituido un enigma en la ciencia a través de los tiempos. Múltiples son las investigaciones realizadas acerca de las causas que lo producen y las consecuencias que provoca. Su importancia no solo radica en lo que significa en la morbilidad y la mortalidad infantil, sino que estos niños tienen habitualmente múltiples problemas posteriores. El Programa para la Reducción del BPN señala que los niños nacidos con un peso inferior a los 2 500 g presentan riesgo de mortalidad 14 veces mayor durante el primer año de vida, en comparación con los niños que nacen con un peso normal a término. Dentro de los factores de riesgo del BPN se han encontrado con mayor frecuencia en estudios realizados por diferentes autores, los siguientes: el embarazo en la adolescencia, la desnutrición en la madre, el hábito de fumar, la hipertensión arterial durante el embarazo, la sepsis cervicovaginal, la anemia y los embarazos gemelares, entre otros. Es innegable la influencia que el BPN tiene sobre las futuras generaciones, por lo que debe constituir la diana de los esfuerzos que el médico y la enfermera deben desarrollar en su prevención, sobre todo en la comunidadLow birth weight has been an enigma for Science through times. A lot of research works have been carried out about its causes and consequences. The importance of LBW not only lies in its meaning for infant mortality and morbidity but also in the many problems that low birth weight children regularly face in the future. The program for the reduction of LBW points out that newborns weighing under 2500g have during his/her first year of life a mortality risk 14 times higher than newborns with a normal weight at term. Among the low birth weight risk factors, a number of studies by various authors have frequently found the following; pregnancy at adolescence; undernourishment in mothers, smoking, blood hypertension during pregnancy, cervix-vaginal sepsis; anemia, twin

  15. Microstructure and mechanical properties of Mg-6Al magnesium alloy with yttrium and neodymium

    Directory of Open Access Journals (Sweden)

    Chen Jun

    2009-05-01

    Full Text Available The effects of rare earth (RE elements Y and Nd on the microstructure and mechanical properties of Mg-6Al magnesium alloy were investigated. The results show that a proper level of RE elements can obviously refi ne the microstructure of Mg-6Al magnesium alloys, reduce the quantity of β-Mg17Al12 phase and form Al2Y and Al2Nd phases. The combined addition of Y and Nd dramatically enhances the tensile strength of the alloys in the temperature range of 20-175℃. When the content of RE elements is up to 1.8%, the values of tensile strength at room temperature and at 150℃ simultaneously reach their maximum of 253 MPa and 196 MPa, respectively. The main mechanisms of enhancement in the mechanical properties of Mg-6Al alloy with Y and Nd are the grain refi ning strengthening and the dispersion strengthening.

  16. De GPS al mapa

    Directory of Open Access Journals (Sweden)

    Esteban Dörries

    2016-03-01

    Full Text Available Las coordenadas Lambert obtenidas a partir de mediciones con equipos GPS de mano, llamados a veces navegadores, en ciertos casos confunden al usuario, por diferir claramente de su posición real al ser graficadas en un mapa del Instituto Geográfico Nacional (IGN: Esto puede resolverse con suficiente exactitud mediante una transformación de Molodensky, seguida de la correspondiente proyección cartográfica. Sin embargo, los tres parámetros necesarios para la transformación, supuestamente válidos para Costa Rica, se encuentran en muchas variantes y producen obviamente resultados diferentes. En este trabajo se analizan los fundamentos del problema y sus posibles soluciones, culminando con un estudio comparativo de ocho casos, que permite seleccionar los valores más adecuados para los parámetros.

  17. ALS insertion devices

    International Nuclear Information System (INIS)

    Hoyer, E.; Chin, J.; Halbach, K.; Hassenzahl, W.V.; Humphries, D.; Kincaid, B.; Lancaster, H.; Plate, D.

    1990-11-01

    The Advanced Light Source (ALS), the first US third generation synchrotron radiation source, is currently under construction at the Lawrence Berkeley Laboratory. The low-emittance, 1.5 GeV electron storage ring and the insertion devices are specifically designed to produce high brightness beams in the UV to soft X-Ray range. The planned initial complement of insertion devices includes four 4.6 m long undulators, with period lengths of 3.9 cm, 5.0 cm (2) and 8.0 cm, and a 2.9 m long wiggler of 16 cm period length. Undulator design is well advanced and fabrication has begun on the 5.0 cm and 8.0 cm period length undulators. This paper discusses ALS insertion device requirements; general design philosophy; and design of the magnetic structure, support structure/drive systems, control system and vacuum system. 18 refs., 9 figs., 5 tabs

  18. Adekola et al (7)

    African Journals Online (AJOL)

    Timothy Ademakinwa

    the South Atlantic between Latitudes 31° and 33.5 ... South Atlantic Ocean in the Early Cretaceous, around 136 Ma (Brown et al., 1996; Reeves and de. Wit, 2000 ..... 3244. 3246.70. L o w e r C re ta c e o u s. P e rio d. /E p o c h. 3244. 3246.70. B a ..... moderate counts of forest species such as ... The other, near shore is rich.

  19. Influence of electric current on microstructure evolution in Ti/Al and Ti/TiAl{sub 3} during spark plasma sintering

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Y. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Haley, J. [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Kulkarni, K. [Department of Materials Science and Engineering, Indian Institute of Technology, Kanpur 208016, UP (India); Aindow, M. [Department of Materials Science and Engineering, Institute of Materials Science, University of Connecticut, Storrs, CT 06269-3136 (United States); Lavernia, E.J., E-mail: lavernia@ucdavis.edu [Department of Chemical Engineering and Materials Science, University of California, Davis, CA 95616-5294 (United States); Department of Chemical Engineering and Materials Science, University of California, Irvine, CA 92697-2575 (United States)

    2015-11-05

    The synthesis of γ-TiAl from elemental metals via solid-state reactive diffusion processing routes involves multiple reaction steps with the formation of various intermediate intermetallic compounds, starting with TiAl{sub 3} because this phase is favored kinetically. To understand the processes by which the TiAl{sub 3} intermediate is eliminated during synthesis of γ-TiAl alloy via spark plasma sintering (SPS), the reaction between Ti and TiAl{sub 3} during SPS was studied with emphasis on the effects of the applied electric current and starting TiAl{sub 3} microstructure on the reaction kinetics and the underlying diffusion mechanisms. The intermediate intermetallic phases Ti{sub 3}Al, TiAl and TiAl{sub 2} were formed between the Ti and TiAl{sub 3} upon SPS processing at 900 °C. The applied electric current did not alter the character of the phases formation in the Ti/TiAl{sub 3} system, but thermodynamic calculations suggest that the activation energy for the nucleation of TiAl{sub 2} is reduced significantly with an electric current flowing. Moreover, the kinetics of the reactions between Ti and TiAl{sub 3} were enhanced when the starting TiAl{sub 3} microstructure was refined. The electric field also had a more significant influence on the grain growth kinetics for TiAl{sub 2} and TiAl in powder blend compacts with refined microstructures. - Highlights: • Reaction between Ti and TiAl{sub 3} during spark plasma sintering was studied. • Refined starting TiAl{sub 3} microstructure enhanced the reactions kinetics. • The nucleation barrier of TiAl{sub 2} was reduced by the applied electric field. • The applied electric field restrained the grain growth of TiAl and TiAl{sub 2}.

  20. The evolution of ultraconserved elements with different phylogenetic origins

    KAUST Repository

    Ryu, Tae Woo

    2012-12-05

    Background: Ultraconserved elements of DNA have been identified in vertebrate and invertebrate genomes. These elements have been found to have diverse functions, including enhancer activities in developmental processes. The evolutionary origins and functional roles of these elements in cellular systems, however, have not yet been determined. Results: Here, we identified a wide range of ultraconserved elements common to distant species, from primitive aquatic organisms to terrestrial species with complicated body systems, including some novel elements conserved in fruit fly and human. In addition to a well-known association with developmental genes, these DNA elements have a strong association with genes implicated in essential cell functions, such as epigenetic regulation, apoptosis, detoxification, innate immunity, and sensory reception. Interestingly, we observed that ultraconserved elements clustered by sequence similarity. Furthermore, species composition and flanking genes of clusters showed lineage-specific patterns. Ultraconserved elements are highly enriched with binding sites to developmental transcription factors regardless of how they cluster. Conclusion: We identified large numbers of ultraconserved elements across distant species. Specific classes of these conserved elements seem to have been generated before the divergence of taxa and fixed during the process of evolution. Our findings indicate that these ultraconserved elements are not the exclusive property of higher modern eukaryotes, but rather transmitted from their metazoan ancestors. 2012 Ryu et al.; licensee BioMed Central Ltd.

  1. Cast AlSi9Cu4 alloy with hybride strenghtened by Fe{sub x}Al{sub y}-Al{sub 2}O{sub 3} composite powder

    Energy Technology Data Exchange (ETDEWEB)

    Piatkowski, J [Department of Materials Technology, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice (Poland); Formanek, B, E-mail: jaroslaw.piatkowski@polsl.pl, E-mail: boleslaw.formanek@polsl.pl [Department of Materials Science, Silesian University of Technology, Krasinskiego 8, 40-019 Katowice (Poland)

    2011-05-15

    The main objective of the study was to develop a technology of dispersion strenghtened hypoeutectic Al-Si alloy. The article presented the materials and technology conception for producing aluminium matrix composite AlSi9Cu4Fe alloy with hybride reinforcement of Al{sub x}Fe{sub y} intermetallic and aluminium oxide powders. Composite powder obtained in mechanical agllomerisation mixture of elemental powders. Changes in the structure were confirmed by TA and ATD thermal analyses plotting the solidification curves, which showed a decrease in temperature T{sub liq} compared to the unmodified alloy and an exothermic effect originating from the crystallisation of eutectics with alloying elements. The examinations carried out by SEM and BSE as well as the determination of local chemical composition by EDX technique have characterised the structure of the alloy as containing some binary Al-Si-Al-Cu and Al-Fe eutectics and multicomponent eutectics.

  2. Sipping test on a failed MTR fuel element

    International Nuclear Information System (INIS)

    Terremoto, Luis Antonio Albiac; Zeituni, Carlos Alberto; Silva, Antonio Teixeira e; Perrotta, Jose Augusto; Silva, Jose Eduardo Rosa da

    2002-01-01

    This work describes sipping tests performed on MTR fuel elements of the IEA-R1 research reactor, in order to determinate which one failed in the core during a routine operation of the reactor. radioactive iodine isotopes 131 I and 133 I, employed as failure indicators, were detected in samples corresponding to the fuel element IEA-156. The specific activity of each sample, as well as the average leaking rate, were measured for 137 Cs. The nuclear fuels U 3 O 8 - Al dispersion and U - Al alloy were compared concerning their measured average leaking rates of 137 Cs. (author)

  3. Synthesis, microstructure and mechanical properties of (Ti1−x,Nbx)2AlC/Al2O3 solid solution composites

    International Nuclear Information System (INIS)

    Zhu, Jianfeng; Han, Na; Wang, Anning

    2012-01-01

    (Ti,Nb) 2 AlC/Al 2 O 3 in-situ solid solution composites were successfully synthesized from the elemental powder mixtures of Nb 2 O 5 , Ti, Al and carbon black using hot-press-aided reaction synthesis. The reaction path was investigated by differential scanning calorimetry (DSC) and X-ray diffractometry (XRD), and a possible reaction mechanism was proposed to explain the formation of (Ti,Nb) 2 AlC/Al 2 O 3 composites in which the thermite reaction between Al and Nb 2 O 5 formed Al 2 O 3 and Nb, and the latter together with TiAl and TiC reacted to form (Ti,Nb) 2 AlC. The synthesized composites show plate-like grains packed in a laminated structure typical of Ti 2 AlC, and the fine Al 2 O 3 particles formed in-situ tend to disperse on the matrix grain boundaries. Compared with the monolithic Ti 2 AlC synthesized using an identical process, the Vickers hardness, maximum compressive stress, flexural strength and fracture toughness of (Ti 0.96 ,Nb 0.04 ) 2 AlC/5 wt% Al 2 O 3 were enhanced by 33.8%, 12.1%, 118.4% and 111.8%, respectively. The mechanisms by which Al 2 O 3 increases the strength and toughness of the material were also discussed.

  4. Fuel element transport container

    International Nuclear Information System (INIS)

    Benna, P.; Neuenfeldt, W.

    1979-01-01

    The reprocessing system includes a large number of waterfilled ponds next to each other for the intermediate storage of fuel elements from LWR's. The fuel element transport device is allocated to a middle pond. The individual ponds are separated from each other by walls, and are only accessible from the middle pond via narrow passages. The transport device includes a telescopic running rail for a trolley with a grab device for the fuel element. The running rail is supported in turn by a second trolley, which can be moved by wheels on rails. Part of the drive of the first trolley is arranged on the second one. Using this transport device, adjacent ponds can be served through the passage openings. (DG) [de

  5. Nuclear fuel element

    International Nuclear Information System (INIS)

    Hirayama, Satoshi; Kawada, Toshiyuki; Matsuzaki, Masayoshi.

    1980-01-01

    Purpose: To provide a fuel element for reducing the mechanical interactions between a fuel-cladding tube and the fuel element and for alleviating the limits of the operating conditions of a reactor. Constitution: A fuel element having mainly uranium dioxide consists of a cylindrical outer pellet and cylindrical inner pellet inserted into the outer pellet. The outer pellet contains two or more additives selected from aluminium oxide, beryllium oxide, magnesium oxide, silicon oxide, sodium oxide, phosphorus oxide, calcium oxide and iron oxide, and the inner pellet contains nuclear fuel substance solely or one additive selected from calcium oxide, silicon oxide, aluminium oxide, magnesium oxide, zirconium oxide and iron oxide. The outer pellet of the fuel thus constituted is reduced in mechanical strength and also in the mechanical interactions with the cladding tube, and the plastic fluidity of the entire pellet is prevented by the inner pellet increased in the mechanical strength. (Kamimura, M.)

  6. Creativity Management Key Elements

    Directory of Open Access Journals (Sweden)

    Rosa María Fuchs Ángeles

    2015-09-01

    Full Text Available Organizations are constantly looking towards innovation. In order to reach it they must foment creativity. This paper analyzes a series of elements considered in the organizational creativity management and proposes a model with the indispensable factors that organizations should consider to reach it. These elements are: culture and organizational environment, strategy, structure, communication, relation with customers, human resources (recruiting, training, job design, compensation, promotion, and performance evaluation, long term orientation and the organizational life cycle. Having the analysis of those elements as a basis, the indispensable pillars on management creativity are identified. The proposed model is based on 5 pillars: the alignment between strategic, culture and organizational structure, called by the authors 'Holy Trinity'; intern publicity; customer’s voice; recognition and a look towards future. Finally, the case of an innovative Peruvian enterprise is presented from the model’s perspective and the study conclusions.

  7. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  8. Uses of a Myth: al-Andalus

    Directory of Open Access Journals (Sweden)

    Serafín Fanjul

    2009-06-01

    Full Text Available In the last two decades, the Spanish press treatment of the Muslim world reflects a change of tone from unsympathetic to enthusiastic, although the information is still marred by confusion and ignorance. This change of attitude has occurred in other Western countries as well, and it is due in part to immigration trends, control over oil resources, and the relativism of official discourses towards the Third World. In the case of Spain, however, there is an additional internal element at play: the mass-media reinvention of a mythical al-Andalus as a tolerant and pluralistic society. This idealized interpretation of seven centuries of Muslim presence in the Iberian Peninsula is fraught with ignorance and distortion of the historical record but is not new. The mystification of al-Andalus has its precedent in romantic accounts that saw in “Muslim Spain” a differential fact that reinforced the exotic image of the country. It can be attributed also to the strategy to “hispanicize” al-Andalus employed by Arabists and historians to make the subject matter appealing to unsympathetic Spanish audiences conditioned by the myth of the Reconquest. Intended or not, the manipulation of the myth of al-Andalus as a historical fact has ideological and political implications that demand an objective and balanced consideration.

  9. Elements of social security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security is a comparative study of important elements of the social security systems in Denmark (DK), Sweden (S), Finland (FIN), Austria (A), Germany (D), the Netherlands (NL), Great Britain (GB) and Canada (CAN). It should be emphasized that Germany is the former West Germany...... (Alte Länder). This is the 9th and last edition of the publication,covering income levels and rules for social security and personal taxation for 1999. Basis for the projections to 1999 income levels is the 1998 data (in some cases 1999 data)for OECD's Taxing Wages as reported by national experts....

  10. Elements of linear space

    CERN Document Server

    Amir-Moez, A R; Sneddon, I N

    1962-01-01

    Elements of Linear Space is a detailed treatment of the elements of linear spaces, including real spaces with no more than three dimensions and complex n-dimensional spaces. The geometry of conic sections and quadric surfaces is considered, along with algebraic structures, especially vector spaces and transformations. Problems drawn from various branches of geometry are given.Comprised of 12 chapters, this volume begins with an introduction to real Euclidean space, followed by a discussion on linear transformations and matrices. The addition and multiplication of transformations and matrices a

  11. Bibliography on transuranium elements

    International Nuclear Information System (INIS)

    Sood, D.D.

    1991-01-01

    A selective bibliography of prominent publications on transuranium elements is compiled. Heading papers, symposia proceedings and the textbooks are included in the bibliography. The bibliography is arranged under the headings: (1)Books, Symposia Proceedings, Reviews etc., (2)Discovery, (3)Weighable Isolation, (4)Metal Preparation, (5)Nuclear Properties, (6)Plutonium as Reactor Fuel, (7)Fuel Reprocessing, (8)Solid State Chemistry, Thermochemistry and Spectroscopy, (9)Radiation Safety, (10)Applications, and (11)Some Typical Indian Papers. Total number of references cited are 298. The bibliography, though selective, will serve as a starting point for comprehensive literature search on transuranium elements. (author)

  12. Finite elements and approximation

    CERN Document Server

    Zienkiewicz, O C

    2006-01-01

    A powerful tool for the approximate solution of differential equations, the finite element is extensively used in industry and research. This book offers students of engineering and physics a comprehensive view of the principles involved, with numerous illustrative examples and exercises.Starting with continuum boundary value problems and the need for numerical discretization, the text examines finite difference methods, weighted residual methods in the context of continuous trial functions, and piecewise defined trial functions and the finite element method. Additional topics include higher o

  13. Elemental Spatiotemporal Variations of Total Suspended Particles in Jeddah City

    OpenAIRE

    Kadi, Mohammad W.

    2014-01-01

    Elements associated with total suspended particulate matter (TSP) in Jeddah city were determined. Using high-volume samplers, TSP samples were simultaneously collected over a one-year period from seven sampling sites. Samples were analyzed for Al, Ba, Ca, Cu, Mg, Fe, Mn, Zn, Ti, V, Cr, Co, Ni, As, and Sr. Results revealed great dependence of element contents on spatial and temporal variations. Two sites characterized by busy roads, workshops, heavy population, and heavy trucking have high lev...

  14. Direct calculation of off-diagonal matrix elements

    International Nuclear Information System (INIS)

    Killingbeck, J P; Jolicard, G

    2011-01-01

    Gauss elimination is used in a sequence of calculations which give the squares of the off-diagonal matrix elements of x between quartic oscillator eigenstates, in a modification of the original sum rule approach of Tipping et al to the problem. New and more flexible methods are then devised and tested and are shown to permit the isolation and calculation of individual squared matrix elements of x and x 2 .

  15. K-AR AGES, MINERALOGY, MAJOR AND TRACE ELEMENT ...

    African Journals Online (AJOL)

    The mafic rocks are characterised by high Fe2O3, TiO2, MgO, CaO and variable enrichment in compatible trace elements (Cr, Ni, Co) all of which abruptly decrease with increase in fractionation. Na2O, K2O and Al2O3 and the LILE increase with magma differentiation. Normalised incompatible trace elements show marked ...

  16. Reactive synthesis of NbAl3 matrix composites

    International Nuclear Information System (INIS)

    Lu, L.; Kim, Y.S.; Gokhale, A.B.; Abbaschian, R.

    1990-01-01

    NbAl 3 matrix composites were synthesized in-situ via reactive hot compaction (RHC) of elemental powders. It was found that the simultaneous application of pressure during synthesis was effective in attaining a near-theoretical density matrix at relatively low temperatures and pressures. Using this technique, two types of composites were produced: matrices containing a uniform dispersion of second phase particles (either Nb 3 Al or Nb 2 Al with an Nb core or Nb 2 Al) and matrices reinforced with coated or uncoated ductile Nb filaments. It was found that a limited amount of toughening is obtained using the first approach, while composites containing coated Nb filaments exhibited a significant increase in the ambient temperature fracture toughness. In this paper, various aspects of RHC processing of NbAl 3 matrix composites, the effect of initial stoichiometry and powder size on the microstructure, as well as the mechanical behavior of the composites are discussed

  17. Trace Elements in Teeth by ICPMS

    International Nuclear Information System (INIS)

    Zahran, N.F.; Helal, A.I.; Amr, M.A.; Amr, M.A.; Al-saad, K.A.

    2008-01-01

    Teeth are reported to be suitable indicators of trace element exposure from environment and nutritional status. Inductively coupled plasma mass spectrometry (ICP-MS) is used to compare the trace element content of children's primary teeth and adult teeth. Primary teeth are collected from 28 children and 42 adult from non-industrial City. The data are assessed statistically using t-tests. The adult teeth contained significantly greater concentrations of Na, Mg, Al, Fe, Ni, Cu, Sr, Cd, Ba, Pb and U and significantly less Mn, Co, As, Se, Mo and Bi than the children teeth. Additional measurements on adult teeth pulps are performed. Comparison between trace element concentrations in health and caries teeth pulps show that the mean concentrations of Na, Al, K, Cr, Mn, Co, Cu, Zn, Mo, Ag, Bi and U are lower in caries than healthy teeth pulps. On the other hand, the mean concentrations of Mg, Cd and Pb are higher in caries samples than healthy teeth pulps

  18. Creep behavior of Ti3Al-Nb intermetallic alloys

    International Nuclear Information System (INIS)

    Yu, T.H.; Yue, W.J.; Koo, C.H.

    1997-01-01

    It is well known that Ti 3 Al-Nb alloys are potential materials for aerospace applications. The creep property is an important consideration when materials are used at high temperature. In this article, the effect of microstructure of Ti-25Al-10Nb alloy on the creep property was investigated, and the creep property of Ti-25Al-10Nb alloy modified by small addition of silicon 0.2 at.% or carbon 0.1 at.% was observed. The alloy with the addition of molybdenum to replace part of niobium 2 at.% was also studied. The experimental results show that the furnace-cooled Ti-25Al-10Nb alloy has superior creep resistance to the air-cooled Ti-25Al-10Nb alloy at 200 MPa, but exhibits poor creep resistance at 250 MPa or above. Small addition of silicon to the Ti-25Al-10Nb alloy may increase creep resistance. Small addition of carbon to the Ti-25Al-10Nb alloy may reduce creep resistance but raise rupture strain. Molybdenum is the most effective alloying element to increase creep resistance for the Ti-25Al-10Nb alloy. The creep mechanism of Ti-25Al-10Nb alloy is governed by dislocation climb. (orig.)

  19. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Austria, Germany, the Netherlands, Great Britain and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable...

  20. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Germany, the Netherlands, Great Britain and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable income...

  1. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Germany, Great Britain, the Netherlands and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable income...

  2. Water, the intangible element

    NARCIS (Netherlands)

    Schotting, R.J.

    2009-01-01

    Water is the key to life. No living creature can survive without water. Too much water or polluted water are serious threats to mankind. Managing this intangible element is complex, not only in wet deltaic regions but also in the (semi-)arid regions of the world. Combined efforts of the

  3. Movies and Literary Elements.

    Science.gov (United States)

    Keller, Rodney D.

    1987-01-01

    Recommends using movie clips to stimulate students' interest in reading a novel as well as to teach elements of fiction such as plot, character, setting, symbol, irony, and theme. Describes each clip and provides study questions. Includes a listing of movies made from books. (NH)

  4. Elements of Architecture

    DEFF Research Database (Denmark)

    Elements of Architecture explores new ways of engaging architecture in archaeology. It conceives of architecture both as the physical evidence of past societies and as existing beyond the physical environment, considering how people in the past have not just dwelled in buildings but have existed...

  5. Inside finite elements

    CERN Document Server

    Weiser, Martin

    2016-01-01

    All relevant implementation aspects of finite element methods are discussed in this book. The focus is on algorithms and data structures as well as on their concrete implementation. Theory is covered as far as it gives insight into the construction of algorithms. Throughout the exercises a complete FE-solver for scalar 2D problems will be implemented in Matlab/Octave.

  6. Plants' essential chemical elements

    Science.gov (United States)

    Kevin T. Smith

    2007-01-01

    Every garden center and hardware store sells fertilizer guaranteed to "feed" plants. In a strict sense, we can't feed plants. Food contains an energy source. Green plants capture solar energy and make their own food through photosynthesis! Photosynthesis and other metabolic processes require chemical elements in appropriate doses for plants to survive...

  7. Elements of relativity theory

    International Nuclear Information System (INIS)

    Lawden, D.F.

    1985-01-01

    The book on elements of relativity theory is intended for final year school students or as an early university course in mathematical physics. Special principle of relativity, lorentz transformation, velocity transformations, relativistic mechanics, and general theory of relativity, are all discussed. (U.K.)

  8. Photovoltaic radiation detector element

    International Nuclear Information System (INIS)

    Agouridis, D.C.

    1980-01-01

    A radiation detector element is formed of a body of semiconductor material, a coating on the body which forms a photovoltaic junction therewith, and a current collector consisting of narrow metallic strips, the aforesaid coating having an opening therein in the edge of which closely approaches but is spaced from the current collector strips

  9. Geochemical study of main elements and trace elements in soils of three profiles in the state of Santa Catarina

    International Nuclear Information System (INIS)

    Santelli, R.E.

    1985-01-01

    The total concentrations of the main components (Si, Al, Fe, Ca, Mg, Mn, Ti, Na and K) and of nine trace elements (Ba, Co, Cu, La, Li, Mo, Ni, V and Zn are measured. The elements are determined by several atomic absorption and emission spectroscopic methods. Some properties such as granulometry, mineralogy of the clay fraction, organic matter, etc, are studied. (M.J.C.) [pt

  10. Southern California Seismic Network: Caltech/USGS Element of TriNet 1997-2001

    OpenAIRE

    Hauksson, Egill; Small, Patrick; Hafner, Katrin; Busby, Robert; Clayton, Robert; Goltz, James; Heaton, Tom; Hutton, Kate; Kanamori, Hiroo; Polet, Jascha

    2001-01-01

    The California Institute of Technology (Caltech), the United States Geological Survey (USGS), and the California Department of Conservation, Division of Mines and Geology (CDMG) are completing the implementation of TriNet, a modern seismic information system for southern California. TriNet consists of two elements, the Caltech-USGS element and the CDMG element (Mori et al., 1998). The Caltech-USGS element (Caltech-USGS TriNet) concentrates on rapid notification and archiving...

  11. Flipped Classroom al laboratori

    OpenAIRE

    Molés Bort, Jaume

    2014-01-01

    L'article presenta una experiència d'aprenentatge de la geologia mitjançant el treball en grups d'experts. Els alumnes han d'indagar i promoure el seu propi aprenentatge per a assolir un repte que se'ls proposa, i consensuar els criteris per els que avaluaran els seus propis resultats mitjançant rúbriques. L'activitat inclou aspectes artístics, TIC i matemàtics, i segueix un esquema similar al de les WebQuest. Els resultats de l'activitat es presenten juntament amb una enquesta realitzada ent...

  12. Teatro al aire libre

    Directory of Open Access Journals (Sweden)

    Philippe Canac

    2016-11-01

    Full Text Available Siendo cada vez más frecuentes y numerosas las peregrinaciones a la basílica de Notre Dame, de Laus (Altos Alpes, su capacidad resultaba hace tiempo insuficiente para acoger a sus peregrinos. Este fue el motivo de crear, en un terreno situado ante el atrio de la basílica, un conjunto, que permitiese celebrar misas al aire libre, ceremonias litúrgicas o representaciones de teatro religioso y que dispusiese de todas las posibilidades para conseguir la libertad del juego escénico.

  13. Architektur als Vermittlung

    OpenAIRE

    Ott, Konrad

    2016-01-01

    Mit Anbruch der Moderne hat sich die Architektur bewußt von den Stilen vorangegangener Epochen losgesagt und sich fortan als Ausdruck einer neuen Kultur, eines neuen Zeitgeistes legitimiert. Der Philosoph Konrad Ott setzt sich mit dem Spannungsfeld zwischen den humanistischen und ästhetischen Ansprüchen der modernen Architektur, wie sie etwa von LeCorbusier formuliert worden sind, und der Realität, die sich etwa in der "Behältnis-Architektur" der Großstädte zeigt, auseinander. Die kritische T...

  14. Salvar al planeta

    OpenAIRE

    Thomas Sancton

    2015-01-01

    El desastre de Exxon Valdez en Canadá (1989)en que derramaron 262 mil barriles de petróleo en las aguas de Alaska cambió la conciencia de los norteamericanos para bien. Comienzan a preocuparse, les gusta ser ecologistas. Se espera que no sea moda o novelería y que asuman el liderazgo para salvar al planeta, pues la deforestación, el incremento de la población, la quema de combustibles fósiles, el calentamiento global, el agujero de ozono sobre la Antártida dejan intuir que la Tierra está en g...

  15. Programa Padres al Colegio

    OpenAIRE

    Viñeglas Fernández, Sandra

    2014-01-01

    El presente trabajo, es un proyecto orientado a la promoción de la salud, en referencia al virus del papiloma humano (VPH), ya que este virus es el causante de una de las infecciones de transmisión sexual más frecuentes en el mundo, el objetivo de este trabajo, es diseñar una serie de intervenciones que contribuyan a sensibilizar e informar a la ciudadanía, para lograr mejorar la prevención del virus del papiloma humano y el cáncer de cérvix. Como ya es sabido, cualquier intervención sobre...

  16. Del Pasadismo al Futurismo

    OpenAIRE

    Agudo-Martínez, M. J.

    2003-01-01

    Uno de los habituales prejuicios a la hora de abordar el análisis del movimiento futurista, al igual que sucede con el constructivismo, es la consideración del contexto político en el que se desarrollaron ambas vanguardias. Sin embargo, y dejando a un lado un enfoque del arte con finalidad política de signo diverso, habría que insistir en el hecho de que posiblemente sean tanto el futurismo italiano como el constructivismo ruso, los movimientos que con mayor entusiasmo se manifestaron, en un ...

  17. Synthesizing (ZrAl3 + AlN)/Mg-Al composites by a 'matrix exchange' method

    Science.gov (United States)

    Gao, Tong; Li, Zengqiang; Hu, Kaiqi; Han, Mengxia; Liu, Xiangfa

    2018-06-01

    A method named 'matrix exchange' to synthesize ZrAl3 and AlN reinforced Mg-Al composite was developed in this paper. By inserting Al-10ZrN master alloy into Mg matrix and reheating the cooled ingot to 550 °C, Al and Mg atoms diffuse to the opposite side. As a result, liquid melt occurs once the interface areas reach to proper compositions. Then dissolved Al atoms react with ZrN, leading to the in-situ formation of ZrAl3 and AlN particles, while the Al matrix is finally replaced by Mg. This study provides a new insight for preparing Mg composites.

  18. Use of plate fuel elements for the RA3 reactor

    International Nuclear Information System (INIS)

    Parodi, C.; Parkanski, D.; Higa, M.; Marajofsky, A.

    1992-01-01

    The RA3 reactor is a pool reactor, redesigned for 5 MW dissipation. Nineteen plates are used in each fuel element. The utilization of 20% enriched U, gives the possibility of the development of rod type fuel with Al/U 3 O 8 cermets. The thermohydraulic and neutronic conditions are studied in this work in order to satisfy the stipulated power. In addition, the fabrication conditions of Al/U 3 O 8 and Al/U 3 O 8 /Zr H 2 cermets with densities within the limits imposed by the thermohydraulics and neutronics conditions are studied. (author)

  19. K-shell x-ray production cross sections of selected elements Al to Ni for 4. 0 to 38. 0 MeV /sup 10/B ions. [Cross sections, 4. 0 to 38 MeV, binding energy, electron capture decay, PWBA, energy shifts, multiple ionization

    Energy Technology Data Exchange (ETDEWEB)

    Monigold, G.; McDaniel, F.D.; Duggan, J.L.; Mehta, R.; Rice, R.; Miller, P.D.

    1976-01-01

    K-Shell x-ray production cross sections for the target elements Sc, Ti, V, Mn, Fe, Co, and Ni were measured for incident /sup 10/B ions over the energy range 4.0 to 38.0 MeV. The cross section data were compared to the theoretical predictions of the binary encounter approximation (BEA); the plane wave born approximation (PWBA); and the PWBA modified to include corrections for increased binding energy (B), Coulomb deflection of the incident ion (C), orbital perturbation due to polarization (P), and relativistic effects (R). In addition, fluorescence yield variations (W/sub K/) and contributions to the cross sections from electron capture (EC) were included. It was found that the predictions of the fully modified PWBA with contributions from electron capture and fluorescence yield variations included provided the best fit to the experimental data over the entire energy range for each target element. The K..beta../K..cap alpha.. x-ray intensity ratios were compared to theoretical values that assume single hole ionization, and the x-ray energy shifts presented as a function of the energy of the incident ion. These two measurements provided confirmation of the occurrence of multiple ionization for /sup 10/B bombardment of target elements in the range 21 less than or equal to Z/sub 2/ less than or equal to 28.

  20. Local chemistry of Al and P impurities in silica

    DEFF Research Database (Denmark)

    Lægsgaard, Jesper; Stokbro, Kurt

    2000-01-01

    The local structure around Al and P impurities in silica is investigated using density-functional theory. Two distinct cases are considered: impurities substituting for a Si atom in alpha quartz, and impurities implanted in a stoichiometric alpha-quartz crystal. Both impurity elements are found t...

  1. Element-topology-independent preconditioners for parallel finite element computations

    Science.gov (United States)

    Park, K. C.; Alexander, Scott

    1992-01-01

    A family of preconditioners for the solution of finite element equations are presented, which are element-topology independent and thus can be applicable to element order-free parallel computations. A key feature of the present preconditioners is the repeated use of element connectivity matrices and their left and right inverses. The properties and performance of the present preconditioners are demonstrated via beam and two-dimensional finite element matrices for implicit time integration computations.

  2. Appiah-Adjei et al

    African Journals Online (AJOL)

    PUBLICATIONS1

    ing, sale of automobile spare parts, and metal fabrication. Some of these activities generate huge ... Keywords: Groundwater quality, pollution, waste disposal, Suame, Ghana ... of fertilizers (Chen et al., 2007; Parris, 2011;. Shen et al., 2011), ...

  3. AL-USRCRN Station Information

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Documentation of United States Alabama Regional Climate Reference Network (AL-USRCRN) installations in 2006. Installations documented are for AL-USRCRN pilot project...

  4. Derivados vinculados al seguro.

    Directory of Open Access Journals (Sweden)

    De Paz Cobo, Sonia

    2003-01-01

    Full Text Available El presente trabajo tiene como objetivo la presentación de los derivados financieros como instrumentos de cobertura de los riesgos del seguro, así como de los principales proyectos que se desarrollan a través de los mismos, como por ejemplo los derivados sobre el clima. Hay que tener presente las pérdidas multimillonarias ocasionadas en casos como el de la banca Baring’s, o el de Orange County, por citar algunas, que si bien ciertos autores afirman que están en relación directa con el uso de estos productos, no podemos olvidar que los instrumentos derivados se desarrollaron con el objetivo principal de proteger al usuario de la posible volatilidad del activo subyacente. Ya en la industria aseguradora los derivados vinculados a tal actividad son instrumentos donde el pago se condiciona a la ocurrencia de su suceso de siniestro, o serie de sucesos múltiples que disparen las pérdidas. Tras el repaso efectuado y la descripción que este tipo de instrumentos puede tener en la gestión del riesgo por parte de la industria aseguradora, concluiremos con la exposición de las relaciones con el reaseguro tradicional así como una breve referencia al futuro de este tipo de instrumentos

  5. The use of natural radioactive Isotopes in the determination of pollution sources of AL-Kabir AL-Shimali river

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Shwiekani, R.; Mamish, S.

    2012-01-01

    In the present research, variations of concentration levels of some natural radioactive isotopes (226 Ra, 210 Po,210 Pb, U and Th isotopes) and some trace elements (Cu, Zn, Pb, Cd) in water and sediments of AL-Kabir AL-Shimali river during the period of 2009-2010 have been studied. The samples were collected along the river from the asphalt factory to the end of the mouth of the river in the Mediterranean Sea. Results showed that concentrations of natural radioactive isotopes have been increased slightly in water and sediments of the river after the asphalt factory and after the factories area, while the concentrations of Rn in the river's water were low along the river except the waters of October 16, Lake Dam that reached a value of 341 mBq/l. These high concentrations in water and sediments of the AL-Kabir AL-Shimali River were due to discharges from the asphalt factory and other factories known to contain natural radioactive isotopes, indicating the possibility of using these isotopes in the determination of pollution sources of AL-Kabir AL-Shimali River. However, the measured concentrations are relatively low compared to the values reported in the world due to river water flow that dilute concentrations of these elements. On the other hand, measurements of trace elements (Cu,Zn,Pb,Cd) showed low concentrations in the waters of the river, with some increases in the concentrations in river sediments after the asphalt factory and the factories area , indicating the contribution of the factories outlets in this increase. The results were compared with the results of previous studies conducted on the Euphrates and the Orontes, where the comparison showed lower values in the AL-Kabir AL-Shimali river environment. (author)

  6. The use of natural radioactive isotopes in the determination of pollution sources of Al-Kabir Al-Shimali river

    International Nuclear Information System (INIS)

    ALmasri, M.; Shweikani, R.; Mamish, S.; Al-Haleem, M.A.; Al-Shamali, K.; Jerby, B.

    2010-10-01

    In the present research, variations of concentration levels of some natural radioactive isotopes ( 226 Ra, 210 Po, 210 Pb, U and Th isotopes) and some trace elements (Cu, Zn, Pb, Cd) in water and sediments of Al-Kabir Al-Shimali river during the period of 2009-2010 have been studied. The samples were collected along the river from the asphalt factory to the end of the mouth of the river in the Mediterranean Sea. Results showed that concentrations of natural radioactive isotopes have been increased slightly in water and sediments of the river after the asphalt factory and after the factories area, while the concentrations of Rn in the river's water were low along the river except the waters of October 16, Lake Dam that reached a value of 341mBq/l. These high concentrations in water and sediments of the Al-Kabir Al-Shimali River were due to discharges from the asphalt factory and other factories known to contain natural radioactive isotopes, indicating the possibility of using these isotopes in the determination of pollution sources of Al-Kabir Al-Shimali River. However, the measured concentrations are relatively low compared to the values reported in the world due to river water flow that dilute concentrations of these elements. On the other hand, measurements of trace elements (Cu,Zn,Pb,Cd) showed low concentrations in the waters of the river, with some increases in the concentrations in river sediments after the asphalt factory and the factories area , indicating the contribution of the factories outlets in this increase. The results were compared with the results of previous studies conducted on the Euphrates and the Orontes, where the comparison showed lower values in the Al-Kabir Al-Shimali river environment.(author)

  7. Concentrations of radioactive elements in lunar materials

    Science.gov (United States)

    Korotev, Randy L.

    1998-01-01

    As an aid to interpreting data obtained remotely on the distribution of radioactive elements on the lunar surface, average concentrations of K, U, and Th as well as Al, Fe, and Ti in different types of lunar rocks and soils are tabulated. The U/Th ratio in representative samples of lunar rocks and regolith is constant at 0.27; K/Th ratios are more variable because K and Th are carried by different mineral phases. In nonmare regoliths at the Apollo sites, the main carriers of radioactive elements are mafic (i.e., 6-8 percent Fe) impact-melt breccias created at the time of basin formation and products derived therefrom.

  8. Embrittling effects of residual elements on steels

    International Nuclear Information System (INIS)

    Brear, J.M.; King, B.L.

    1979-01-01

    In a review of work related to reheat cracking in nuclear pressure vessel steels, Dhooge et al referred to work of the authors on the relative embrittling parameter for SA533B steels. The poor agreement when these parameters were applied to creep ductility data for SA508 class 2 lead the reviewers to conclude that the relative importance of impurity elements is a function of base alloy composition. The authors briefly describe some of their more recent work which demonstrates that when various mechanical, and other, effects are taken into consideration, the relative effects of the principal residual elements are similar, despite differing base compositions, and that the embrittling parameters derived correlate well with the data for SA Class 2 steel. (U.K.)

  9. Bukti Kebenaran Al-quran

    OpenAIRE

    Aliyah, Sri

    2015-01-01

    Al Quran is the greatest miracles of Muhammad SAW as the direction of humankind in order to reach eternal happiness. Scientific evidences show that Al Quran has the truth massages, although it was released far before the finding of modern sciences. The researches continue to study the truth of Al Quran an it revealed the historical fact.

  10. The production of transplutonium elements in France

    International Nuclear Information System (INIS)

    Koehly, G.; Bourges, J.; Madic, C.; Sontag, R.; Kertesz, C.

    1980-08-01

    The development of the program for the production of transplutonium elements, 241 Am, 243 Am and 244 Cm, in France, required a major effort from the technological and chemical standpoints. Pre-existing hot cells were reconditioned and others specially built for these production operations. From the chemical standpoint, the development of extractive chromatography on the preparative scale has allowed the definition of simple processes. This type of process, initially developed for the treatment of Pu/Al targets, is ideal for the treatment of industrial wastes for their decontamination and for the production of 241 Am

  11. Tribological investigations of surface treated Ti6Al4V

    International Nuclear Information System (INIS)

    Rueck, D.M.; Schminke, A.; Schmidt, H.; Soltani-Farshi, M.; Baumann, H.; Fink, U.; Richter, E.

    1998-05-01

    The tribological couple of the titanium alloy Ti6Al4V and ultrahigh molecular weight polyethylene (UHMWPE) is used for hip and knee joint prostheses. It is known that surface treatment of the titanium alloy Ti6Al4V by ion implantation of various elements can improve the wear behavior of such prostheses. The results of tribological tests, performed in Ringer solution with a ring-on-disc tester, show that oxygen in the implanted near surface region has a pronounced influence on the wear performance. Oxygen can be introduced into the surface by different mechanisms: either by direct implantation of oxygen ions or by indiffusion during the implantation of other elements like nitrogen or carbon at higher temperatures. The influence of the oxygen content in the near surface region of implanted and nonimplanted Ti6Al4V on the tribological performance is discussed in detail. (orig.)

  12. X-ray determination of static displacements of atoms in alloyed Ni3Al

    International Nuclear Information System (INIS)

    Morinaga, M.; Sone, K.; Kamimura, T.; Ohtaka, K.; Yukawa, N.

    1988-01-01

    Single crystals of Ni 3 (Al, M) were grown by the Bridgman method, where M is Ti, V, Cr, Mn, Fe, Nb, Mo and Ta. The composition was controlled to be about Ni 75 Al 20 M 5 so that the alloying element, M, substitutes mainly for Al. With these crystals conventional X-ray structural analysis was performed. The measured static displacements of atoms from the average lattice points depended largely on the alloying elements and varied in the range 0.00-0.13 A for Ni atoms and 0.09-0.18 A for Al atoms. It was found that these atomic displacements correlated well with the atomic radius of the alloying element, M. For example, when the atomic radius of M is larger than that of Al, the static displacements are large for the atoms in the Al sublattice but small for the atoms in the Ni sublattice. By contrast, when the atomic radius of M is smaller than that of Al, the displacements are more enhanced in the Ni sublattice than in the Al sublattice. Thus, there is an interesting correlation between the atomic displacements in both the Al and Ni sublattices in the presence of alloying elements. This seems to be one of the characteristics of alloyed compounds with several sublattices. (orig.)

  13. Internal/external mixing of aerosol particles elemental composition retrieved from microPIXE and PIXE

    International Nuclear Information System (INIS)

    Ghermandi, G.; Cecchi, R.; Lusvarghi, L.; Laj, P.; Zappoli, S.; Ceccato, D.

    2005-01-01

    A statistical evaluation of the association between different elements contained in atmospheric aerosol particles has been made using the microPIXE technique. We derived elemental maps of Al, Si, S, Ca, Cl, K, Fe, Mg spatial distribution on the surface of a Nuclepore filter sample. The microPIXE measurements are validated by comparison to conventional PIXE and SEM-EDAX. Then, the spatial coherence of the different elements is analysed using statistical methods. The elements are not homogeneously distributed and the association among specific elements can be identified. MicroPIXE and factorial analysis can be coupled to understand the state of mixing of the different elements on the filter surface

  14. Archaeal extrachromosomal genetic elements

    DEFF Research Database (Denmark)

    Wang, Haina; Peng, Nan; Shah, Shiraz Ali

    2015-01-01

    SUMMARY: Research on archaeal extrachromosomal genetic elements (ECEs) has progressed rapidly in the past decade. To date, over 60 archaeal viruses and 60 plasmids have been isolated. These archaeal viruses exhibit an exceptional diversity in morphology, with a wide array of shapes, such as spind......SUMMARY: Research on archaeal extrachromosomal genetic elements (ECEs) has progressed rapidly in the past decade. To date, over 60 archaeal viruses and 60 plasmids have been isolated. These archaeal viruses exhibit an exceptional diversity in morphology, with a wide array of shapes...... on archaeal ECEs has just started to unravel the molecular biology of these genetic entities and their interactions with archaeal hosts, it is expected to accelerate in the next decade....

  15. Nuclear fuel element

    Energy Technology Data Exchange (ETDEWEB)

    Armijo, J S; Coffing, L F

    1979-04-05

    The fuel element with circular cross-section for BWR and PWR consists of a core surrounded by a compound jacket container where there is a gap between the core and jacket during operation in the reactor. The core consists of U, Pu, Th compounds and mixtures of these. The compound jacket consists of zircaloy 2 or 4. In order to for example prevent the corrosion of the compound jacket, its inner surface has a metal barrier with smaller neutron absorbers than the jacket material in the form of a zirconium sponge. The zirconium of this metal barrier has impurities of various elements in the order of magnitude of 1000 to 5000 ppm. The oxygen content is in the range of 200 to 1200 ppm and the thickness of the metal barrier is 1-30% of the thickness of the jacket.

  16. Nuclear reactor fuel element

    International Nuclear Information System (INIS)

    D'Eye, R.W.M.; Shennan, J.V.; Ford, L.H.

    1977-01-01

    Fuel element with particles from ceramic fissionable material (e.g. uranium carbide), each one being coated with pyrolitically deposited carbon and all of them being connected at their points of contact by means of an individual crossbar. The crossbar consists of silicon carbide produced by reaction of silicon metal powder with the carbon under the influence of heat. Previously the silicon metal powder together with the particles was kneaded in a solvent and a binder (e.g. epoxy resin in methyl ethyl ketone plus setting agent) to from a pulp. The reaction temperature lies at 1750 0 C. The reaction itself may take place in a nitrogen atmosphere. There will be produced a fuel element with a high overall thermal conductivity. (DG) [de

  17. Nuclear fuel element

    International Nuclear Information System (INIS)

    1974-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed. A heat conducting fission product retaining metal liner of a refractory metal is incorporated in the fuel element between the cladding and the nuclear fuel to inhibit mechanical interaction between the nuclear fuel and the cladding, to isolate fission products and nuclear fuel impurities from contacting the cladding, and to improve the axial thermal peaking gradient along the length of the fuel rod. The metal liner can be in the form of a tube or hollow cylindrical column, a foil of single or multiple layers in the shape of a hollow cylindrical column, or a coating on the internal surface of the cladding. Preferred refractory metal materials are molybdenum, tungsten, rhenium, niobium and alloys of the foregoing metals

  18. Nuclear fuel element

    International Nuclear Information System (INIS)

    Thompson, J.R.; Rowland, T.C.

    1976-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed. A heat conducting, fission product retaining metal liner of a refractory metal is incorporated in the fuel element between the cladding and the nuclear fuel to inhibit mechanical interaction between the nuclear fuel and the cladding, to isolate fission products and nuclear fuel impurities from contacting the cladding and to improve the axial thermal peaking gradient along the length of the fuel rod. The metal liner can be in the form of a tube or hollow cylindrical column, a foil of single or multiple layers in the shape of a hollow cylindrical column, or a coating on the internal surface of the cladding. Preferred refractory metal materials are molybdenum, tungsten, rhenium, niobium and alloys of the foregoing metals

  19. Elements of quantum optics

    CERN Document Server

    Meystre, Pierre

    2007-01-01

    Elements of Quantum Optics gives a self-contained and broad coverage of the basic elements necessary to understand and carry out research in laser physics and quantum optics, including a review of basic quantum mechanics and pedagogical introductions to system-reservoir interactions and to second quantization. The text reveals the close connection between many seemingly unrelated topics, such as probe absorption, four-wave mixing, optical instabilities, resonance fluorescence and squeezing. It also comprises discussions of cavity quantum electrodynamics and atom optics. The 4th edition includes a new chapter on quantum entanglement and quantum information, as well as added discussions of the quantum beam splitter, electromagnetically induced transparency, slow light, and the input-output formalism needed to understand many problems in quantum optics. It also provides an expanded treatment of the minimum-coupling Hamiltonian and a simple derivation of the Gross-Pitaevskii equation, an important gateway to rese...

  20. Periodic table of elements

    International Nuclear Information System (INIS)

    Fluck, E.; Heumann, K.G.

    1985-01-01

    Following a recommendation by the International Union for Pure and Applied Chemistry (IUPAC), the groups of the periodic table shall be numbered from 1 to 18, instead of I to VIII as before. The recommendations has been approved of by the Committee on Nomenclature of the American Chemical Society. The new system abandons the distinction between main groups (a) and auxiliary groups (b), which in the past frequently has been the reason for misunderstandings between European and American chemists, due to different handling. The publishing house VCH Verlagsgesellschaft recently produced a new periodic table that shows the old and the new numbering system together at a glance, so that chemists will have time to get familiar with the new system. In addition the new periodic table represents an extensive data compilation arranged by elements. The front page lists the chemical properties of elements, the back page their physical properties. (orig./EF) [de

  1. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Nakai, Keiichi

    1983-01-01

    Purpose: To decrease the tensile stresses resulted in a fuel can as well as prevent decladding of fuel pellets into the bore holes by decreasing the inner pressure within the nuclear fuel element. Constitution: A fuel can is filled with hollow fuel pellets, inserted with a spring for retaining the hollow fuel pellets with an appropriate force and, thereafter, closely sealed at the both ends with end plugs. A cylindrical body is disposed into the bore holes of the hollow fuel pellets. Since initial sealing gases and/or gaseous nuclear fission products can thus be excluded from the bore holes where the temperature is at the highest level, the inner pressure of the nuclear fuel element can be reduced to decrease the tensile strength resulted to the fuel can. Furthermore, decladding of fuel pellets into the bore holes can be prevented. (Moriyama, K.)

  2. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Ainsworth, K.F.

    1979-01-01

    A nuclear fuel element is described having a cluster of nuclear fuel pins supported in parallel, spaced apart relationship by transverse cellular braces within coaxial, inner and outer sleeves, the inner sleeve being in at least two separate axial lengths, each of the transverse braces having a peripheral portion which is clamped peripherally between the ends of the axial lengths of the inner sleeve. (author)

  3. Sensor for ionizable elements

    International Nuclear Information System (INIS)

    Berkey, E.; Reed, W.A. III; Hickam, W.M.

    1977-01-01

    Sensor to detect thermally ionizable elements or molucules in air, water vapour or oxygen or to be used as alkali leak detector in vacuum systems, e.g. in the pipe system of a liquid-metal cooled FBR. The sensor consists of an filament made of thorium-containing iridium as cathode with a temperature upto 1000 0 C and an anode sheet of molybdenum, nickel or stainless steal. (ORU) [de

  4. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Butterfield, C.E.; Waite, E.

    1982-01-01

    A nuclear reactor fuel element comprising a column of vibration compacted fuel which is retained in consolidated condition by a thimble shaped plug. The plug is wedged into gripping engagement with the wall of the sheath by a wedge. The wedge material has a lower coefficient of expansion than the sheath material so that at reactor operating temperature the retainer can relax sufficient to accommodate thermal expansion of the column of fuel. (author)

  5. OXIDATION OF TRANSURANIC ELEMENTS

    Science.gov (United States)

    Moore, R.L.

    1959-02-17

    A method is reported for oxidizing neptunium or plutonium in the presence of cerous values without also oxidizing the cerous values. The method consists in treating an aqueous 1N nitric acid solution, containing such cerous values together with the trivalent transuranic elements, with a quantity of hydrogen peroxide stoichiometrically sufficient to oxidize the transuranic values to the hexavalent state, and digesting the solution at room temperature.

  6. Transportation of radioactive elements

    International Nuclear Information System (INIS)

    Thubert, Francis; Rentien, Guy; Jacquet, Michel

    1981-01-01

    The production and marketing of artificial radioactive elements engaged in by the 'Office des Rayonnements Ionisants' requires the use of specially designed packagings and assorted means of transport. The authors begin by describing the different kinds of products involved and the forms of packagings needed, and go on to discuss the various means of transport used, underlining the fact that, in terms of number and gravity, the incidents that have occurred to date have indeed been few and far between [fr

  7. Vented nuclear fuel element

    International Nuclear Information System (INIS)

    Oguma, M.; Hirose, Y.

    1976-01-01

    A description is given of a vented nuclear fuel element having a plenum for accumulation of fission product gases and plug means for delaying the release of the fission product gases from the plenum, the plug means comprising a first porous body wettable with a liquid metal and a second porous body non-wettable with the liquid metal, the first porous body being impregnated with the liquid metal and in contact with the liquid metal

  8. Irradiation behaviour of U-Si-Al with peripheral voidage

    International Nuclear Information System (INIS)

    Fehrenbach, P.J.; Feraday, M.A.; Cotnam, K.D.; Morel, P.A.

    1977-12-01

    Peripheral voidage in the form of longitudinal slots on the surface of the fuel is effective in accommodating the irradiation induced swelling of U-Si-Al rods clad in cold-worked Zr-2.5 wt% Nb. Diametral increases in elements operated at steady powers between 50 and 80 kW/m to a burnup of 240 MW.h/kg U were less than 1.25%. Similar to U 3 Si elements, lower sheath strength or higher temperatures resulted in greater diametral increases. An oxide or graphite interlayer between the fuel and sheath was shown to be effective in preventing the development of a fuel/sheath bond. The ability of U-Si-Al elements to successfully survive a power increase from 35 to 70 kW/m after appreciable burnup at the lower power has also been demonstrated. (author)

  9. Trace element studies at University of Pittsburgh

    International Nuclear Information System (INIS)

    Cohen, B.L.; Chan, K.C.; Shabason, L.; Wedberg, G.; Rudolph, H.

    1974-01-01

    Seven areas of research are discussed. A method was developed for analyzing samples for their major constituent elements by irradiating with protons and detecting prompt gamma rays, mostly produced in (p,p'γ) reactions. Among other applications, the method was used to analyze air particulates for C, N, O, Al, Si, S, Co, and Fe. Trace element analysis by proton or alpha particle induced x-ray fluorescence was used on thin samples in a study of the variations of Pb, Br, Fe, and Zn in air particulates as a function of time. Among other applications this method was also used in studying trace elements in rainwater. An x-ray fluorescence method that is effective in the analysis of thick samples was developed. A method based on measuring energies of elastically scattered protons was developed for the analysis of light elements. The use of proton and neutron activation analyses, as well as methods for studying depth profiles for hydrogen and helium in materials are discussed

  10. Nwidu et al., Afr J Tradit Complement Altern Med. (2014) 11(2):257 ...

    African Journals Online (AJOL)

    cadewumi

    ... semi-preparative HPLC, and the structures established by NMR (Nwidu et al., 2012b). ... fingerprint of the ESE, preliminary phyto-chemical screening, elemental and ..... Prostaglandins and serotonin: Non-peptide diarrheagenic hormones.

  11. Helium the disappearing element

    CERN Document Server

    Sears, Wheeler M

    2015-01-01

    The subject of the book is helium, the element, and its use in myriad applications including MRI machines, particle accelerators, space telescopes, and of course balloons and blimps. It was at the birth of our Universe, or the Big Bang, where the majority of cosmic helium was created; and stellar helium production continues. Although helium is the second most abundant element in the Universe, it is actually quite rare here on Earth and only exists because of radioactive elements deep within the Earth. This book includes a detailed history of the discovery of helium, of the commercial industry built around it, how the helium we actually encounter is produced within the Earth, and the state of the helium industry today. The gas that most people associate with birthday party balloons is running out. “Who cares?” you might ask. Well, without helium, MRI machines could not function, rockets could not go into space, particle accelerators such as those used by CERN could not operate, fiber optic cables would not...

  12. Elements of quantum information

    International Nuclear Information System (INIS)

    Schleich, W.P.

    2007-01-01

    Elements of Quantum Information introduces the reader to the fascinating field of quantum information processing, which lives on the interface between computer science, physics, mathematics, and engineering. This interdisciplinary branch of science thrives on the use of quantum mechanics as a resource for high potential modern applications. With its wide coverage of experiments, applications, and specialized topics - all written by renowned experts - Elements of Quantum Information provides and indispensable, up-to-date account of the state of the art of this rapidly advancing field and takes the reader straight up to the frontiers of current research. The articles have first appeared as a special issue of the journal 'Fortschritte der Physik / Progress of Physics'. Since then, they have been carefully updated. The book will be an inspiring source of information and insight for anyone researching and specializing in experiments and theory of quantum information. Topics addressed in Elements of Quantum Information include - Cavity Quantum Electrodynamics - Segmented Paul Traps - Cold Atoms and Bose-Einstein Condensates in Microtraps, Optical Lattices, and on Atom Chips - Rydberg Gases - Factorization of Numbers with Physical Systems - Entanglement of Continuous Variables - NMR and Solid State Quantum Computation - Quantum Algorithms and Quantum Machines - Complexity Theory - Quantum Crytography. (orig.)

  13. Using Finite Element Method

    Directory of Open Access Journals (Sweden)

    M.H.R. Ghoreishy

    2008-02-01

    Full Text Available This research work is devoted to the footprint analysis of a steel-belted radial tyre (185/65R14 under vertical static load using finite element method. Two models have been developed in which in the first model the tread patterns were replaced by simple ribs while the second model was consisted of details of the tread blocks. Linear elastic and hyper elastic (Arruda-Boyce material models were selected to describe the mechanical behavior of the reinforcing and rubbery parts, respectively. The above two finite element models of the tyre were analyzed under inflation pressure and vertical static loads. The second model (with detailed tread patterns was analyzed with and without friction effect between tread and contact surfaces. In every stage of the analysis, the results were compared with the experimental data to confirm the accuracy and applicability of the model. Results showed that neglecting the tread pattern design not only reduces the computational cost and effort but also the differences between computed deformations do not show significant changes. However, more complicated variables such as shape and area of the footprint zone and contact pressure are affected considerably by the finite element model selected for the tread blocks. In addition, inclusion of friction even in static state changes these variables significantly.

  14. Study of Superheavy Elements

    International Nuclear Information System (INIS)

    Hofmann, Sigurd

    2007-01-01

    The nuclear shell model predicts that the next doubly magic shell-closure beyond 208 Pb is at a proton number Z = 114, 120, or 126 and at a neutron number N = 172 or 184. The outstanding aim of experimental investigations is the exploration of this region of spherical 'SuperHeavy Elements' (SHEs). Experimental methods are described, which allowed for the identification of elements produced on a cross-section level of about 1 pb. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission, not fission. Decay properties as well as reaction cross-sections are compared with results of theoretical investigations. Finally, plans are presented for the further development of the experimental set-up and the application of new techniques, as for instance the precise mass measurement of the produced nuclei using ion traps. At increased sensitivity, the detailed exploration of the region of spherical SHEs will start, after first steps on the island were made in recent years. (Author)

  15. Probabilistic finite elements

    Science.gov (United States)

    Belytschko, Ted; Wing, Kam Liu

    1987-01-01

    In the Probabilistic Finite Element Method (PFEM), finite element methods have been efficiently combined with second-order perturbation techniques to provide an effective method for informing the designer of the range of response which is likely in a given problem. The designer must provide as input the statistical character of the input variables, such as yield strength, load magnitude, and Young's modulus, by specifying their mean values and their variances. The output then consists of the mean response and the variance in the response. Thus the designer is given a much broader picture of the predicted performance than with simply a single response curve. These methods are applicable to a wide class of problems, provided that the scale of randomness is not too large and the probabilistic density functions possess decaying tails. By incorporating the computational techniques we have developed in the past 3 years for efficiency, the probabilistic finite element methods are capable of handling large systems with many sources of uncertainties. Sample results for an elastic-plastic ten-bar structure and an elastic-plastic plane continuum with a circular hole subject to cyclic loadings with the yield stress on the random field are given.

  16. New functionalities in abundant element oxides: ubiquitous element strategy

    International Nuclear Information System (INIS)

    Hosono, Hideo; Hayashi, Katsuro; Kamiya, Toshio; Atou, Toshiyuki; Susaki, Tomofumi

    2011-01-01

    While most ceramics are composed of ubiquitous elements (the ten most abundant elements within the Earth's crust), many advanced materials are based on rare elements. A 'rare-element crisis' is approaching owing to the imbalance between the limited supply of rare elements and the increasing demand. Therefore, we propose a 'ubiquitous element strategy' for materials research, which aims to apply abundant elements in a variety of innovative applications. Creation of innovative oxide materials and devices based on conventional ceramics is one specific challenge. This review describes the concept of ubiquitous element strategy and gives some highlights of our recent research on the synthesis of electronic, thermionic and structural materials using ubiquitous elements. (topical review)

  17. Salvar al planeta

    Directory of Open Access Journals (Sweden)

    Thomas Sancton

    2015-01-01

    Full Text Available El desastre de Exxon Valdez en Canadá (1989en que derramaron 262 mil barriles de petróleo en las aguas de Alaska cambió la conciencia de los norteamericanos para bien. Comienzan a preocuparse, les gusta ser ecologistas. Se espera que no sea moda o novelería y que asuman el liderazgo para salvar al planeta, pues la deforestación, el incremento de la población, la quema de combustibles fósiles, el calentamiento global, el agujero de ozono sobre la Antártida dejan intuir que la Tierra está en grave peligro. Se recomienda entonces optar por un desarrollo sustentable.

  18. COMENTARIO AL CASO PINOCHET

    Directory of Open Access Journals (Sweden)

    Alberto Contreras Clunes

    2002-01-01

    Full Text Available El fallo en el caso Pinochet tiene distintas formas de ser analizado. De partida, desde un punto de vista político, también constitucional, del derecho penal. Sin embargo, nos abocaremos al estudio desde el punto de vista procesal, en especial a lo referido al Debido Proceso. Para ello se analizará los presupuestos, la solución dada por la Excma. Corte Suprema y las consecuencias del mismo. Además, se criticará la solución dada, desde la óptica de las garantías procesales del imputado, contenidas en el nuevo proceso penal y lo dispuesto en la Constitución y la Convención Americana de Derechos Humanos. Finalmente, se argumentará en favor de una interpretación finalista y armónica de la Constitución y los tratados internacionales de derechos humanos.The verdict of the Pinochet Case has different ways of being analyzed: from the political, the constitutional, and the penal law points of view. However, we will approach this study from the legal point of view, especially to that referred to as the Proper Process. To do this, the budgets, the solution given by the Most Excellent Supreme Court, and its consequences will be analyzed. Furthermore, the given solution will be criticized from the point of view of the legal guarantees of the accused contained in the new penal process and what is contained in the Constitution and in the American Convention of Human Rights. In conclusion, we will argue in favor of a final and harmonious interpretation of the Constitution and the international agreement of human rights.

  19. Effect of truncated cone roughness element density on hydrodynamic drag

    Science.gov (United States)

    Womack, Kristofer; Schultz, Michael; Meneveau, Charles

    2017-11-01

    An experimental study was conducted on rough-wall, turbulent boundary layer flow with roughness elements whose idealized shape model barnacles that cause hydrodynamic drag in many applications. Varying planform densities of truncated cone roughness elements were investigated. Element densities studied ranged from 10% to 79%. Detailed turbulent boundary layer velocity statistics were recorded with a two-component LDV system on a three-axis traverse. Hydrodynamic roughness length (z0) and skin-friction coefficient (Cf) were determined and compared with the estimates from existing roughness element drag prediction models including Macdonald et al. (1998) and other recent models. The roughness elements used in this work model idealized barnacles, so implications of this data set for ship powering are considered. This research was supported by the Office of Naval Research and by the Department of Defense (DoD) through the National Defense Science & Engineering Graduate Fellowship (NDSEG) Program.

  20. Elemental analysis in cultured cells, tobacco and grape, treated with aluminum

    International Nuclear Information System (INIS)

    Tanoi, K.; Iikura, H; Nakanishi, T.M.

    2001-01-01

    Relationship between Al toxicity and the Al, Fe and B amount of element in tobacco and grape cells are discussed. Al and Fe were analyzed by neutron activation analysis and B was analyzed by prompt gamma-ray analysis. Callose content was also measured as an indicator of cell damage induced Al toxicity. When tobacco cells were incubated in 1 mM and 300 μM Al solution, the pattern of callose formation was much similar to that of Fe accumulation than that of Al accumulation in tobacco cells, suggesting that the increase of Fe content induced toxic effect along with Al incorporated into the cells. However, this tendency was not observed in grape cells. Boron content did not show any relation to those of Al or Fe throughout the Al treatment in both tobacco and grape cells. (author)

  1. Determination of chilling temperature effects on nutrient elements ...

    African Journals Online (AJOL)

    These seedlings were subsequently, cut into root tip, root middle part, root upper part, hypocotyl, epicotyl, petiole and leaf and sampled randomly. Concentrations of inorganic elements (Al, Si, P, S, Cl, K, Ca, Fe, and Mg) in the parts were measured by wavelength-dispersive X-ray fluorescence (WDXRF) spectrometry to test ...

  2. Comment on 'Modelling of surface energies of elemental crystals'

    International Nuclear Information System (INIS)

    Li Jinping; Luo Xiaoguang; Hu Ping; Dong Shanliang

    2009-01-01

    Jiang et al (2004 J. Phys.: Condens. Matter 16 521) present a model based on the traditional broken-bond model for predicting surface energies of elemental crystals. It is found that bias errors can be produced in calculating the coordination numbers of surface atoms, especially in the prediction of high-Miller-index surface energies. (comment)

  3. Full Development Of Pseudopotentials That Work For All Elements ...

    African Journals Online (AJOL)

    (1982) as well as the prescription of Pattnaik et al.(1979) which eliminated the numerical instability problems. The liquid metal resistivity is evaluated using Simpson's rule. Keywords: Pseudopotential, liquid metal resistivity, matrix element, linear coefficients, inverse orthogonality transformation. Nigerian Journal of Physics ...

  4. Carta al Editor

    Directory of Open Access Journals (Sweden)

    Darío Maldonado Romero

    1991-03-01

    Full Text Available

    Bogotá, 01 de Agosto de 1990
    Señores
    Miembros del Consejo Editorial
    Academia Nacional de Medicina
    E.S.D.

    Señores doctores:

    Con toda consideración y respeto me permito agregar algunas anotaciones al escrito del Académico Alberto Cárdenas Escobar, aparecido en el No. 22 de Medicina, para destacar algunos aspectos de la personalidad del doctor Alberto Schweitzer galardonado con el Premio Nobel de la Paz.

    A los 30 años de edad tomó una decisión dramática: Estudiar Medicina para trabajaren el África Ecuatorial. Cuando terminó sus investigaciones sobre enfermedades tropicales y sus prácticas hospitaLarias, partió para el Gabon al pequeño pueblo de Lambarené. La tarea era desconsoladora; La atención médica había que prestarla al aire libre; iba con su esposa, como enfermera y amanuense, y no se encontraba ni un intérprete, ni un ayudante. Cuando le llegaron la medicina y el equipaje hubo que acomodarlos en un viejo gallinero abandonado; el calor era insoportable y le venían enfermos de varias millas a la redonda, a pie o en Canoas.

    Las enfermedades más difundidas eran Malaria, Disentería, estreptococias y la más mortífera, la Tripanosomiasis Gambiense, para la que empezaban a llegar medicinas nuevas eficaces y las medidas preventivas como el suministro de agua potable y enmallado de ventanas impedían muchas contaminaciones.

    Pero la que causaba mayores dificultades y trabajo era la Mycobacteriasis Anestesiante, incurable, de difícil diagnóstico, afectando a varios miembros de la misma familia, de aspecto horripilante, con complicaciones neuríticas muy dolorosas, frecuente ceguera, e invalideces y procesos erisepelatososacrotéricos, que exigían acompañante para el cambio y lavado de vendas y suministro de alimentos.

    A menos de un año de

  5. The transuranium elements: From neptunium and plutonium to element 112

    International Nuclear Information System (INIS)

    Hoffman, D.C.

    1996-01-01

    Beginning in the 1930's, both chemists and physicists became interested in synthesizing new artificial elements. The first transuranium element, Np, was synthesized in 1940. Over the past six decades, 20 transuranium elements have been produced. A review of the synthesis is given. The procedure of naming the heavy elements is also discussed. It appears feasible to produce elements 113 and 114. With the Berkeley Gas-filled Separator, it should be possible to reach the superheavy elements in the region of the spherical Z=114 shell, but with fewer neutrons than the N=184 spherical shell. 57 refs, 6 figs

  6. Development of an efficient grain refiner for Al-7Si alloy and its modification with strontium

    Energy Technology Data Exchange (ETDEWEB)

    Kori, S.A.; Murty, B.S.; Chakraborty, M. [Indian Inst. of Technol., Kharagpur (India). Dept. of Metall. and Mater. Eng.

    2000-05-15

    The grain refining response of Al and Al-7Si alloy has been studied with various Al-Ti, Al-B and Al-Ti-B master alloys at different addition levels. The results show that Al-B and B rich Al-Ti-B master alloys cannot grain refine Al, while they are efficient grain refiners to Al-7Si alloy. The level of grain refinement saturates after 0.03% of Ti or B for most of the master alloys studied both at short and long holding times. The grain refining efficiency of some elements other than Ti and B on Al-7Si alloy has also been studied. Interestingly, all the elements studied (B, Cr, Fe, Mg, Ni, Ti and Zr) have resulted in some grain refinement of Al-7Si alloy at short holding time and have shown fading/poisoning on long holding, which increased in the order of B (no poisoning), Ti, Cr, Ni, Fe, Mg, Zr. Sr (0.02%) has been found to provide complete modification of the eutectic in Al-7Si alloy within 2 min, which is not lost even after long holding up to 120 min. Significant improvements in the mechanical properties have been obtained by a combination of grain refinement and modification to an extent that was not possible by either of them alone. (orig.)

  7. Fabrication-process-induced variations of Nb/Al/AlOx/Nb Josephson junctions in superconductor integrated circuits

    International Nuclear Information System (INIS)

    Tolpygo, Sergey K; Amparo, Denis

    2010-01-01

    Currently, superconductor digital integrated circuits fabricated at HYPRES, Inc. can operate at clock frequencies approaching 40 GHz. The circuits present multilayered structures containing tens of thousands of Nb/Al/AlO x /Nb Josephson junctions (JJs) of various sizes interconnected by four Nb wiring layers, resistors, and other circuit elements. In order to be fully operational, the integrated circuits should be fabricated such that the critical currents of the JJs are within the tight design margins and the proper relationships between the critical currents of JJs of different sizes are preserved. We present experimental data and discuss mechanisms of process-induced variations of the critical current and energy gap of Nb/Al/AlO x /Nb JJs in integrated circuits. We demonstrate that the Josephson critical current may depend on the type and area of circuit elements connected to the junction, on the circuit pattern, and on the step in the fabrication process at which the connection is made. In particular, we discuss the influence of (a) the junction base electrode connection to the ground plane, (b) the junction counter electrode connection to the ground plane, and (c) the counter electrode connection to the Ti/Au or Ti/Pd/Au contact pads by Nb wiring. We show that the process-induced changes of the properties of Nb/Al/AlO x /Nb junctions are caused by migration of impurity atoms (hydrogen) between the different layers comprising the integrated circuits.

  8. Trace elements in a North Sea drill core

    DEFF Research Database (Denmark)

    Kunzendorf, Helmar; Gwozdz, R.; Svendsen, N.

    1986-01-01

    , V, Sr, Dy, Mg, Ti, Ba and Eu. The major elements Ca and Al could be related to petrophysical parameters, particularly Al which shows a correlation with the silicification/argillaceous content. Na (and Cl) has a low content in the hydrocarbon-bearing section of the drill core suggesting that the pore......Chalk samples, systematically taken along a drill core from one of the hydrocarbon producing fields of the North Sea (Tyra field), were analysed by a neutron activation technique involving measurement of radioisotopes with relatively short half-lives. Elements determined include Na, Al, Cl, Ca, Mn...... space is filled mainly by hydrocarbons. A significant decrease of Mn with depth probably suggests diagenesis of chalk prior to, or with, hydrocarbon emplacement. Investigations of drilling fluids and cuttings reveal a strong contamination of the latter, mainly by Ba. Chalk data from comparable onshore...

  9. Elements of social action

    Directory of Open Access Journals (Sweden)

    Marjanović Miloš

    2011-01-01

    Full Text Available Because of the significant analytical advantages, the author prefers social action as initial sociological concept in the relation to social phenomenon. Its basic elements are: actors, subjects and tools, needs and interests, values and norms, positions and roles. Actors set in motion and unify the rest of elements, guide to the magic triangle of sociology (movement, change, order, reaffirm actor paradigm to systemic paradigm. Subjects and tools materialize an action and its overestimate results in technological determinism or (by means of property as institutional appropriation of nature in the (unclassed historical type of society. Needs and interests are the basis of person's motivation and starting point for depth analysis of sociability. The expansion of legitimate interests circle develops techniques of normative regulation. Values and norms guide to institutional-organizational, positions to vertical and roles to horizontal structure. Values give the meaning to the action as well as to human existence, they are orientations of motivate system of personality but also basic aspect of society. As abstractions, values are latent background of norms and they tell to us what to do, and norms how to do something. Norms are specified instructions for suitable behavior Without normative order, not to be possible the satisfying of needs and the conciliation of interests. Riches, power and prestige are components of social position, and legal status is the determination of rights and obligations of the position. Roles are normative expectation of behavior. Toward kinds of sanctions roles are classified. Roles but also other elements of social action are starting point for sociological analysis of legal norms and institutes. On the other side, the observation of legal component of social actions enriches, strengths and precises sociological analysis of them.

  10. Elemental Study in Soybean and Products by Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Vorapot, Permnamtip; Arporn Busamongkol; Sirinart, Laoharojanaphand

    2009-07-01

    Full text: Elements were analyzed in soybean and products by Instrumental Neutron Activation Analysis (INAA), Pseudo-Cyclic Instrumental Neutron Activation Analysis (PCINAA) and Epithermal Instrumental Neutron Activation Analysis (EINAA). Elements detected in sample were include Al, Br, Ca, Cl, Cu, Fe, I, K, Mg, Mn Na, Se and Zn. The result showed that the nutritional contents changed after food processing. From experiments (n = 2), it was found that after food processing, the concentration of Cl and Na in soy bean curd increased from 0.0045 and 0.0011% to found 0.91 and 0.39 %, respectively. Other elements did not differ from soybean. Limits of detection for Al, Br, Ca, Cl, Cu, Fe, I, K, Mg, Mn Na, Se and Zn were 0.05, 0.2, 50, 6, 10, 15, 0.05, 30, 40, 5, 5, 0.05 and 1 mg.kg - 1, respectively

  11. Trace elements retained in washed nuclear fuel reprocessing solvents

    International Nuclear Information System (INIS)

    Gray, L.W.; MacMurdo, K.W.

    1979-09-01

    Analysis of purified TBP extractant from solvent extraction processes at Savannah River Plant showed several stable elements and several long-lived radioisotopes. Stable elements Al, Na, Br, Ce, Hg, and Sm are found in trace quantities in the solvent. The only stable metallic element consistently found in the solvent was Al, with a concentration which varies from about 30 ppM to about 10 ppM. The halogens Br and Cl appear to be found in the solvent systems as organo halides. Radionuclides found were principally 106 Ru, 129 I, 3 H, 235 U, and 239 Pu. The 129 I concentration was about 1 ppM in the first solvent extraction cycle of each facility. In the other cycles, 129 I concentration varied from about 0.1 to 0.5 ppM. Both 129 I and 3 H appear to be in the organic solvent as a result of exchange with hydrogen

  12. Analytical elements of mechanics

    CERN Document Server

    Kane, Thomas R

    2013-01-01

    Analytical Elements of Mechanics, Volume 1, is the first of two volumes intended for use in courses in classical mechanics. The books aim to provide students and teachers with a text consistent in content and format with the author's ideas regarding the subject matter and teaching of mechanics, and to disseminate these ideas. The book opens with a detailed exposition of vector algebra, and no prior knowledge of this subject is required. This is followed by a chapter on the topic of mass centers, which is presented as a logical extension of concepts introduced in connection with centroids. A

  13. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    Klepfer, H.H.

    1974-01-01

    A nuclear fuel element is described which comprises: 1) an elongated clad container, 2) a layer of high lubricity material being disposed in and adjacent to the clad container, 3) a low neutron capture cross section metal liner being disposed in the clad container and adjacent to the layer, 4) a central core of a body of nuclear fuel material disposed in and partially filling the container and forming an internal cavity in the container, 5) an enclosure integrally secured and sealed at each end of the container, and a nuclear fuel material retaining means positioned in the cavity. (author)

  14. Elements of real analysis

    CERN Document Server

    Sprecher, David A

    2010-01-01

    This classic text in introductory analysis delineates and explores the intermediate steps between the basics of calculus and the ultimate stage of mathematics: abstraction and generalization.Since many abstractions and generalizations originate with the real line, the author has made it the unifying theme of the text, constructing the real number system from the point of view of a Cauchy sequence (a step which Dr. Sprecher feels is essential to learn what the real number system is).The material covered in Elements of Real Analysis should be accessible to those who have completed a course in

  15. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E. D.

    1984-01-01

    An array of rods is assembled to form a fuel element for a pressurized water reactor, the rods comprising zirconium alloy sheathed nuclear fuel pellets and containing helium. The helium gas pressure is selected for each rod so that it differs substantially from the helium gas pressure in its closest neighbors. In a preferred arrangement the rods are arranged in a square lattice and the helium gas pressure alternates between a relatively high value and a relatively low value so that each rod has as its closest neighbors up to four rods containing helium gas at the other pressure value

  16. Nuclear reactor fuel elements

    Energy Technology Data Exchange (ETDEWEB)

    Hindle, E. D.

    1984-10-16

    An array of rods is assembled to form a fuel element for a pressurized water reactor, the rods comprising zirconium alloy sheathed nuclear fuel pellets and containing helium. The helium gas pressure is selected for each rod so that it differs substantially from the helium gas pressure in its closest neighbors. In a preferred arrangement the rods are arranged in a square lattice and the helium gas pressure alternates between a relatively high value and a relatively low value so that each rod has as its closest neighbors up to four rods containing helium gas at the other pressure value.

  17. Osteoporosis and trace elements

    DEFF Research Database (Denmark)

    Aaseth, J.; Boivin, G.; Andersen, Ole

    2012-01-01

    More than 200 million people are affected by osteoporosis worldwide, as estimated by 2 million annual hip fractures and other debilitating bone fractures (vertebrae compression and Colles' fractures). Osteoporosis is a multi-factorial disease with potential contributions from genetic, endocrine...... in new bone and results in a net gain in bone mass, but may be associated with a tissue of poor quality. Aluminum induces impairment of bone formation. Gallium and cadmium suppresses bone turnover. However, exact involvements of the trace elements in osteoporosis have not yet been fully clarified...

  18. [Healthcare marketing elements].

    Science.gov (United States)

    Ameri, Cinzia; Fiorini, Fulvio

    2014-01-01

    Marketing puts its foundation on a few key concepts: need-demand, product-service, satisfaction, exchange, market, or business structure manufacturing / supply. The combination of these elements allows you to build an effective marketing strategy. Crucial in this respect is to remember the Porter matrix, which shows that for a correct analysis of the relevant market is necessary to refer to the "five forces at play", ie: customers, competitors, new entrants and substitutes threat. Another key lever for proper marketing oriented approach is the continuous and constant monitoring of the application, anticipating their dissatisfactions.

  19. Technical Elements (CCT1)

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    2017-01-01

    Many of the aspects dealt with in the CA EPBD are closely interlinked with each other and may refer to both new and existing buildings, as well as to inspection and certification. This is also true for technical aspects, such as the calculation methodologies, and how to include technical systems......’ efficiency or how to integrate renewable energy within them. The central team for Technical Elements deals with issues of a technical nature, which are common to new and existing buildings, and/or with minimum demands, certification and inspection. This report focuses on the implementation of Articles 3, 4...

  20. Optical Finite Element Processor

    Science.gov (United States)

    Casasent, David; Taylor, Bradley K.

    1986-01-01

    A new high-accuracy optical linear algebra processor (OLAP) with many advantageous features is described. It achieves floating point accuracy, handles bipolar data by sign-magnitude representation, performs LU decomposition using only one channel, easily partitions and considers data flow. A new application (finite element (FE) structural analysis) for OLAPs is introduced and the results of a case study presented. Error sources in encoded OLAPs are addressed for the first time. Their modeling and simulation are discussed and quantitative data are presented. Dominant error sources and the effects of composite error sources are analyzed.

  1. Elements of energy conversion

    CERN Document Server

    Russell, Charles R

    2013-01-01

    Elements of Energy Conversion brings together scattered information on the subject of energy conversion and presents it in terms of the fundamental thermodynamics that apply to energy conversion by any process. Emphasis is given to the development of the theory of heat engines because these are and will remain most important power sources. Descriptive material is then presented to provide elementary information on all important energy conversion devices. The book contains 10 chapters and opens with a discussion of forms of energy, energy sources and storage, and energy conversion. This is foll

  2. Malamih al-Ashwat al-'Arabiyyah wa Makharijaha

    Directory of Open Access Journals (Sweden)

    Amrah Muhammad Kasim

    2015-12-01

    Full Text Available This writing discusses on al-ashwat al-‘arabiyyah that is known with “phonetic” term. It talks and interprets makharij al-huruf or place for producing sounds and also processing production of sounds by parts of mouth in Arabic language. The problems of sounds and its systems in Arabic language have been conducted by the scholars of al-ashwat al-‘arabiyyah attractively, neatly, and detail and gotten ahead the phonetic western scholars. Part of their analysis results formulate the study about al-ashwat al-sakinah (al-Shamit is known with vocal and consonant sounds in research questions shawait – shawamit. Ibnu Jinni has formulated “harakat”(wowel in Arabic language and dimension of letter  mad and liyn on alif  letter - waw - ya’ (ا و ي, from these letters create  harakat fathah, dammah, and kasrah. Moreover, in this writing also exist the description of hija’i letters and its makhraj that are correct from parts of mouth and the unity of coordinative sounds that produce sounds in morphemes arrangement, in one word that produces meaning. The result of phonological study has divided al-ashwat to be kinds of sound like the pronounced sounds, produced sounds from mouth, and heard sound.

  3. Sorption of selenium on Mg-Al and Mg-Al-Eu layered double hydroxides

    International Nuclear Information System (INIS)

    Curtius, H.; Paparigas, Z.; Kaiser, G.

    2008-01-01

    Salt domes represent deep geological formations which are under consideration as final repositories for irradiated research reactor fuel elements. For long-term safety aspects the mobilisation of the radionuclides due to a water ingress is intensively investigated. At the Institute of Energy Research (IEF-6), leaching experiments were performed in a hot cell facility with UAl x -Al and U 3 Si 2 -Al dispersed research reactor fuel elements in repository-relevant MgCl 2 -rich salt brines under anaerobic conditions. The fuel plates corroded completely within one year and a Mg-Al-layered double hydroxide (LDH) with chloride as interlayer anion was identified as one crystalline phase component of the corrosion products (secondary phases). This Mg-Al-LDH was synthesized, characterized, and the ability to retard europium by an incorporation process was investigated. Europium, as a representative for lanthanides, was identified to be one of the radionuclides which were found in the corrosion products. We could show that europium was incorporated in the lattice structure. LDHs have high anion exchange capacities that enhance their potential to remove anionic contaminants from aqueous systems. In this work the sorption behaviour of selenium in the chemical form as selenite (SeO 3 2- ) on Mg-Al-LDH and on Mg-Al-Eu-LDH was investigated. Especially the influence of the larger europium-III ion was of interest. It represents in the Mg-Al-Eu-LDH about 10% of the molar aluminium amount. The sorption has been experimentally studied in a wide range of pH, ionic strength, radionuclide and sorbent concentration. Both LDHs with chloride as interlayer anion were synthesized by a coprecipitation method under controlled conditions, and their main physico-chemical properties were analyzed prior to the sorption experiments. The sorption kinetics of selenite on the LDHs in water and in MgCl 2 -rich brine were rapid using a LDH concentration of 10 g/L. Equilibrium, indicated by stable p

  4. Evaluation of alkaline dissolution of Al 6061 and Al 1050 for the production of Mo-99 from LEU targets

    International Nuclear Information System (INIS)

    Mindrisz, Ana C.; Camilo, Ruth L.; Araujo, Izilda C.; Forbicini, Christina A.L.G. de O.

    2013-01-01

    Since 2008, due to the global crisis in the production of radioisotope 99 Mo, which product of decay, 99m Tc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo. Studies on the alkaline dissolution to obtain 9 9M o from irradiated UAl x -Al LEU targets are under development. Processing time should be minimized, considering the short half-life of 99 Mo and 99m Tc, about 66 h and 6 h, respectively. This makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of 'scraps' of Al 6061 and 1050, used to simulate the dissolution process of UAl x -Al targets. Dissolution time and gas releasing were evaluated using the following alkaline solutions: a) NaOH 3 mol.L -1 and NaNO 3 2 mol.L -1 , b) NaOH 3 mol.L -1 and NaNO 3 4 mol.L -1 . The initial temperature of dissolution was 85 deg C in all cases. Al 6061 showed values of dissolution time greater than that for Al 1050, 25% for NaNO 3 2 mol.L -1 and 104.55% for NaNO 3 4 mol.L -1 . The dissolution with NaNO 3 2 mol.L -1 showed that the gas releasing for Al 6061 was 2.7% greater than for Al 1050. However Al 1050 showed that gas releasing 9.92% greater than for Al 6061 during the dissolution with NaNO 3 4 mol.L -1 . The decision about what type of alloy has to be used, Al 1050 or Al 6061, it will be upto the group that will manufacture the targets for the RMB. (author)

  5. Determination of Trace Elements in Thai Cereal

    International Nuclear Information System (INIS)

    Permnamtip, Vorapot; Busamongkol, Arporn; Laoharojanaphand, Sirinart; Chaiyasith, Suwan

    2007-08-01

    Full text: Trace elements were analyzed in Thai cereal, e.g. rice and bean, by using neutron activation analysis (NAA). The selected cereals are major food items for Thai population. The data obtained from this work will be useful for nutrition and safety consumption of Thai cereal. Trace elements verified include Al, As, Br, Ca, Cd, Cl, Cr, Cu, Fe, I, K, Mg, Mn, Mo, Se, Sn, V and Zn. It was found that Al, As, Br, Cl, Cu, Fe, Mn, Zn, Ca, K and Mg are presented in the range of 2.2 to 35.7, 0.15 to 0.21, 0.44 to 13.5, 55.6 to 640.3, 16.3 to 16.5, 158.9 to 161.1, 12.2 to 55.7, 8.2 to 58.1 (g/g (ppm) , 0.02 to 0.28, 0.09 to 1.99 and 0.03 to 0.26 %, respectively. For Cd, Cr, I, Mo, Se, Sn and V were not found in sample because the concentrations were lower than detection limit. Precision and accuracy were determined by analyzing standard reference materials: NIST 1568a, NIST 8704, ACSP DORM-1, NIES No.9 and NMIJ 7302 to a

  6. Morton et al. Reply

    Science.gov (United States)

    Morton, Douglas C.; Nagol, Jyoteshwar; Carabajal, Claudia C.; Rosette, Jacqueline; Palace, Michael; Cook, Bruce D.; Vermote, Eric F.; Harding, David J.; North, Peter R. J.

    2016-01-01

    Multiple mechanisms could lead to up-regulation of dry-season photosynthesis in Amazon forests, including canopy phenology and illumination geometry. We specifically tested two mechanisms for phenology-driven changes in Amazon forests during dry-season months, and the combined evidence from passive optical and lidar satellite data was incompatible with large net changes in canopy leaf area or leaf reflectance suggested by previous studies. We therefore hypothesized that seasonal changes in the fraction of sunlit and shaded canopies, one aspect of bidirectional reflectance effects in Moderate Resolution Imaging Spectroradiometer (MODIS) data, could alter light availability for dry-season photosynthesis and the photosynthetic capacity of Amazon forests without large net changes in canopy composition. Subsequent work supports the hypothesis that seasonal changes in illumination geometry and diffuse light regulate light saturation in Amazon forests. These studies clarify the physical mechanisms that govern light availability in Amazon forests from seasonal variability in direct and diffuse illumination. Previously, in the debate over light limitation of Amazon forest productivity, seasonal changes in the distribution of light within complex Amazon forest canopies were confounded with dry-season increases in total incoming photosynthetically active radiation. In the accompanying Comment, Saleska et al. do not fully account for this confounding effect of forest structure on photosynthetic capacity.

  7. Alternativen als Programm

    Directory of Open Access Journals (Sweden)

    Paulina Dobroć

    2018-03-01

    Full Text Available Der vorliegende Artikel soll einen Beitrag zu theoretischen Überlegungen einer Technikfolgenabschätzung (TA der Alternativen leisten. Ausgehend von der Annahme, dass TA seit ihrer Entstehung den Anspruch auf die Entwicklung von (technischen Alternativen erhoben hat, wird hier der Versuch unternommen, die Rolle der TA im Rahmen aktueller Innovationsprozesse zu reflektieren und (neu zu definieren. Dies scheint vor allem im Hinblick auf aktuelle gesellschaftliche Herausforderungen notwendig. Zu diesem Zweck wird eine Grundannahme Lothar Hacks über das Verhältnis von Gesellschaft und Technik herangezogen. Seine Annahme besagt, dass die kontinuierliche Überführung von sozialen Problemen und Leitbildern in enge technische Lösungsansätze in hochindustrialisierten Ländern dominant und Teil der aktuellen gesellschaftlichen Probleme ist. Diese These wird im vorliegenden Artikel im Hinblick auf einen Perspektivenwechsel als Ausgangspunkt eines zukünftigen Forschungsprogramms der TA fruchtbar gemacht. Hierbei bildet das Denken in Alternativen von gesellschaftlichen Zukünften den zentralen Fokus.

  8. Fine structure at the diffusion welded interface of Fe3Al/Q235 ...

    Indian Academy of Sciences (India)

    Unknown

    iron lattice sites (Fair and Wood 1994). 3.2 TEM morphology at the diffusion joint of. Fe3Al/Q235. For the welding of dissimilar materials, the element diffusion and phase formed at the interface of dissimilar. Table 1. Chemical composition and thermophysical properties of Fe3Al intermetallic compound. Chemical composition ...

  9. Nuclear fuel element

    International Nuclear Information System (INIS)

    Iwano, Yoshihiko.

    1993-01-01

    Microfine cracks having a depth of less than 10% of a pipe thickness are disposed radially from a central axis each at an interval of less than 100 micron over the entire inner circumferential surface of a zirconium alloy fuel cladding tube. For manufacturing such a nuclear fuel element, the inside of the cladding tube is at first filled with an electrolyte solution of potassium chloride. Then, electrolysis is conducted using the cladding tube as an anode and the electrolyte solution as a cathode, and the inner surface of the cladding tube with a zirconium dioxide layer having a predetermined thickness. Subsequently, the cladding tube is laid on a smooth steel plate and lightly compressed by other smooth steel plate to form microfine cracks in the zirconium dioxide layer on the inner surface of the cladding tube. Such a compressing operation is continuously applied to the cladding tube while rotating the cladding tube. This can inhibit progress of cracks on the inner surface of the cladding tube, thereby enabling to prevent failure of the cladding tube even if a pellet/cladding tube mechanical interaction is applied. Accordingly, reliability of the nuclear fuel elements is improved. (I.N.)

  10. Heavy-element nucleosynthesis

    International Nuclear Information System (INIS)

    Mathews, G.J.

    1990-01-01

    New measurements and theoretical studies of nuclear properties, together with new astronomical data on the growth of heavy-element abundances during the early history of the Galaxy, now provide a clearer picture of where in nature the elements heavier than iron are produced by rapid (r-process) and show (s-process) neutron capture reactions. The nuclear data suggest that the r-process involves a high-neutron-density beta-flow equilibrium environment and that the s-process may have occurred at a temperature and neutron density consistent with a 13 C(α,n) 16 0 neutron source. The astronomical data, when compared with simple galactic chemical evolution modes, suggests that the r-process is associated with type II supernovae and that the neutron source must be manufactured by the star. Low-mass type II supernovae are proposed as the most important contributors to the r-process. A 13 C neutron source in intermediate-mass stars is proposed for the s-process. 64 refs., 7 figs

  11. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    1980-01-01

    The invention is of a nuclear fuel element which comprises a central core of a body of nuclear fuel material selected from the group consisting of compounds of uranium, plutonium, thorium and mixtures thereof, and an elongated composite cladding container comprising a zirconium alloy tube containing constituents other than zirconium in an amount greater than about 5000 parts per million by weight and an undeformed metal barrier of moderate purity zirconium bonded to the inside surface of the alloy tube. The container encloses the core so as to leave a gap between the container and the core during use in a nuclear reactor. The metal barrier is of moderate purity zirconium with an impurity level on a weight basis of at least 1000ppm and less than 5000ppm. Impurity levels of specific elements are given. Variations of the invention are also specified. The composite cladding reduces chemical interaction, minimizes localized stress and strain corrosion and reduces the likelihood of a splitting failure in the zirconium alloy tube. Other benefits are claimed. (U.K.)

  12. Neutron activation analysis for environmental trace element research determination of elemental composition of sediments in the Sea of Galillee, Israel

    Energy Technology Data Exchange (ETDEWEB)

    Lavi, N; Ne` eman, E; Brenner, S; Butenko, V [Tel Aviv Univ. (Israel). Medical School

    1996-12-01

    The aims of this work were to: a) demonstrate the effectiveness of instrumental neutron activation analysis for determining the background concentrations of trace elements in the sediments collected from the Sea of Gallile. b) determine the advantage factors for epithermal neutron irradiation. c) determine the contribution of silicon to the total {sup 28}Al activity by the {sup 28}Si(n,p){sup 28}Al reaction. c) check the validity of the method by determining the elemental content of U.S. NBS Standard Reference Material SRM-1633a (fly ash). d) calculate the average enrichment factors for the elements in sediments . e) determine the concentrations of the artificial radionuclides {sup 134}Cs, {sup 137}Cs and the naturally occurring radionuclides {sup 40}K, {sup 226}Ra and {sup 232}Th (authors).

  13. Elemental composition of solar energetic particles

    International Nuclear Information System (INIS)

    Cook, W.R. III.

    1981-01-01

    The Low Energy Telescopes on the Voyager spacecraft are used to measure the elemental composition (2 less than or equal to Z less than or equal to 28) and energy spectra (5 to 15 MeV/nucleon) of solar energetic particles (SEPs) in seven large flare events. Four flare events are selected which have SEP abundance ratios approximately independent of energy/nucleon. The abundances for these events are compared from flare to flare and are compared to solar abundances from other sources - spectroscopy of the photosphere and corona, and solar wind measurements. The selected SEP composition results may be described by an average composition plus a systematic flare-to-flare deviation about the average. For each of the four events, the ratios of the SEP abundances to the four-flare average SEP abundances are approximately monotonic functions of nuclear charge Z in the range 6 less than or equal to Z less than or equal to 28. An exception to this Z-dependent trend occurs for He, whose abundance relative to Si is nearly the same in all four events. The four-flare average SEP composition is significantly different from the solar composition determined by photospheric spectroscopy: the elements C, N and O are depleted in SEPs by a factor of about five relative to the elements Na, Mg, Al, Si, Ca, Cr, Fe, and Ni. For some elemental abundance ratios (e.g. Mg/O), the difference between SEP and photospheric results is persistent from flare to flare and is apparently not due to a systematic difference in SEP energy/nucleon spectra between the elements, nor to propagation effects which would result in a time-dependent abundance ratio in individual flare events

  14. Intertekstualiteit als positioneringsstrategie

    Directory of Open Access Journals (Sweden)

    Ewa Dynarowicz

    2015-01-01

    Full Text Available This article explores the discursive role of intertextual references to medieval Persian poets, representatives of the Sufi tradition, in the work of Kader Abdolah, the internationally successful Dutch author of Iranian descent. Most references are authorial ones, that is, they do not refer to a particular text, but to the author of the text, sometimes in a fictionalized form, sometimes mentioning him as a historical figure. At first glance many of these references seem to be redundant elements of the narrative, merely responsible for creating an exoticism effect. Nevertheless, applying Bourdieu’s theoretical perspective on the formation of cultural capital, they can be assumed to fulfill an important strategic purpose. Firstly, they may allow Abdolah to position himself in the Dutch literary field as a writer-refugee, thus seeking connection with a tradition that is commonly positively received by a West-European readership. Secondly, they enhance prestige of the author, signaling Abdolah as a descendant of a classical literary tradition.

  15. Annex 5 - Fabrication of U-Al alloy; Prilog 5 - Dobijanje legure U-Al

    Energy Technology Data Exchange (ETDEWEB)

    Drobnjak, Dj; Lazarevic, Dj; Mihajlovic, A [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

    1961-12-15

    Alloy U-Al with low content of aluminium is often used for fabrication of fuel elements because it is stable under moderate neutron flux density. Additionally this type of alloys show much better characteristics than pure uranium under reactor operating conditions (temperature, mechanical load, corrosion effect of water). This report contains the analysis of the phase diagram of U-Al alloy with low content of aluminium, applied procedure for alloying and casting with detailed description of equipment. Characteristics of the obtained alloy are described and conclusions about the experiment and procedure are presented. Sistem U-Al sa niskim sadrzajem aluminijuma jedan je od cesto koriscenih za izradu gorivnih elemenata, jer je dovoljno stabilan pri umerenim gustinama fluksa. Pored toga, u uslovima karakteristicnim za rad nuklearnog reaktora (temperatura, gradijent temperature, mehanicka naprezanja, koroziono dejstvo vode) legure ovog sistema pokazuju daleko bolja svojstva od nelegiranog urana. Referat sadrzi analizu dijagrama stanja U-Al legure sa niskim sadrzajem aluminijuma, primenjeni postupak legiranja i livenja sa opisom pojedinih uredjaja i operacija. Takodje su opisana svojstva dobijene legure i dat je zakljucak o eksperimentu i tehnici rada (author)

  16. NIH Common Data Elements Repository

    Data.gov (United States)

    U.S. Department of Health & Human Services — The NIH Common Data Elements (CDE) Repository has been designed to provide access to structured human and machine-readable definitions of data elements that have...

  17. Preclinical Studies of Induced Pluripotent Stem Cell-Derived Astrocyte Transplantation in ALS

    Science.gov (United States)

    2012-10-01

    Pluripotent Stem Cell -Derived Astrocyte Transplantation in ALS PRINCIPAL INVESTIGATOR: Nicholas J. Maragakis, M.D...Pluripotent Stem Cell -Derived Astrocyte Transplantation in ALS 5b. GRANT NUMBER W81XWH-10-1-0520 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d...into astrocytes following transplantation. 15. SUBJECT TERMS Stem Cells , iPS cells, astrocytes, familial ALS 16. SECURITY CLASSIFICATION OF

  18. An Improved Model for FE Modeling and Simulation of Closed Cell Al-Alloy Foams

    OpenAIRE

    Hasan, MD. Anwarul

    2010-01-01

    Cell wall material properties of Al-alloy foams have been derived by a combination of nanoindentation experiment and numerical simulation. Using the derived material properties in FE (finite element) modeling of foams, the existing constitutive models of closed-cell Al-alloy foams have been evaluated against experimental results. An improved representative model has been proposed for FE analysis of closed-cell Al-alloy foams. The improved model consists of a combination of spherical and cruci...

  19. Scanning Auger microscopy for high lateral and depth elemental sensitivity

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, E., E-mail: eugenie.martinez@cea.fr [CEA, LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France); Yadav, P. [CEA, LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France); Bouttemy, M. [Institut Lavoisier de Versailles, 45 av. des Etats-Unis, 78035 Versailles Cedex (France); Renault, O.; Borowik, Ł.; Bertin, F. [CEA, LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France); Etcheberry, A. [Institut Lavoisier de Versailles, 45 av. des Etats-Unis, 78035 Versailles Cedex (France); Chabli, A. [CEA, LETI, MINATEC Campus, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France)

    2013-12-15

    Highlights: •SAM performances and limitations are illustrated on real practical cases such as the analysis of nanowires and nanodots. •High spatial elemental resolution is shown with the analysis of reference semiconducting Al{sub 0.7}Ga{sub 0.3}As/GaAs multilayers. •High in-depth elemental resolution is also illustrated. Auger depth profiling with low energy ion beams allows revealing ultra-thin layers (∼1 nm). •Analysis of cross-sectional samples is another effective approach to obtain in-depth elemental information. -- Abstract: Scanning Auger microscopy is currently gaining interest for investigating nanostructures or thin multilayers stacks developed for nanotechnologies. New generation Auger nanoprobes combine high lateral (∼10 nm), energy (0.1%) and depth (∼2 nm) resolutions thus offering the possibility to analyze the elemental composition as well as the chemical state, at the nanometre scale. We report here on the performances and limitations on practical examples from nanotechnology research. The spatial elemental sensitivity is illustrated with the analysis of Al{sub 0.7}Ga{sub 0.3}As/GaAs heterostructures, Si nanowires and SiC nanodots. Regarding the elemental in-depth composition, two effective approaches are presented: low energy depth profiling to reveal ultra-thin layers (∼1 nm) and analysis of cross-sectional samples.

  20. Mechanical clinching process stress and strain in the clinching of EN-AW5754 (AlMg3, and EN AW-5019 (AlMg5 metal plates

    Directory of Open Access Journals (Sweden)

    J. Cumin

    2018-01-01

    Full Text Available This paper presents the results of Finite Element Method numerical simulation performed onEN-AW5754(AlMg3, EN AW-5019 (AlMg5 plates subjected to mechanical clinching. The goal was to observe differences between aluminum plates in the same tool; and to determine the possibility of using the constructed tool for the clinching of Al-Al material combinations. This tool construction is to be produced and tested in laboratory conditions, to elaborate prospective results, and reach additional conclusions.

  1. Joining elements of silicon carbide

    International Nuclear Information System (INIS)

    Olson, B.A.

    1979-01-01

    A method of joining together at least two silicon carbide elements (e.g.in forming a heat exchanger) is described, comprising subjecting to sufficiently non-oxidizing atmosphere and sufficiently high temperature, material placed in space between the elements. The material consists of silicon carbide particles, carbon and/or a precursor of carbon, and silicon, such that it forms a joint joining together at least two silicon carbide elements. At least one of the elements may contain silicon. (author)

  2. Chemical and electrical characterisation of the segregation of Al from a CuAl alloy (90%:10% wt) with thermal anneal

    Energy Technology Data Exchange (ETDEWEB)

    Byrne, C., E-mail: conor.byrne2@mail.dcu.ie [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland); Brady, A.; Walsh, L.; McCoy, A.P.; Bogan, J. [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland); McGlynn, E. [School of Physical Sciences, National Centre for Plasma Science and Technology, Dublin City University, Dublin 9 (Ireland); Rajani, K.V. [School of Electronic Engineering, Dublin City University, Dublin 9 (Ireland); Hughes, G. [School of Physical Sciences, Dublin City University, Dublin 9 (Ireland); School of Physical Sciences, National Centre for Plasma Science and Technology, Dublin City University, Dublin 9 (Ireland)

    2016-01-29

    A copper–aluminium (CuAl) alloy (90%:10% wt) has been investigated in relation to segregation of the alloying element Al, from the alloy bulk during vacuum anneal treatments. X-ray photoelectron spectroscopy (XPS) measurements were used to track the surface enrichment of Al segregating from the alloy bulk during in situ ultra-high vacuum anneals. Secondary ion mass spectroscopy (SIMS) indicates a build-up of Al at the surface of the annealed alloy relative to the bulk composition. Metal oxide semiconductor (MOS) CuAl/SiO{sub 2}/Si structures show a shift in flatband voltage upon thermal anneal consistent with the segregation of the Al to the alloy/SiO{sub 2} interface. Electrical four point probe measurements indicate that the segregation of Al from the alloy bulk following thermal annealing results in a decrease in film resistivity. X-ray diffraction data shows evidence for significant changes in crystal structure upon annealing, providing further evidence for expulsion of Al from the alloy bulk. - Highlights: • CuAl alloy (90%:Al 10% wt) deposited and vacuum annealed • XPS and SIMS data show segregation of Al from the alloy bulk. • Chemical changes seen indicate the reduction of Cu oxide and growth of Al Oxide. • Electrical measurements indicate a chemical change at the metal/SiO{sub 2} interface. • All data consistent with Cu diffusion barrier layer formed.

  3. Undulators at the ALS

    International Nuclear Information System (INIS)

    Hoyer, E.; Akre, J.; Chin, J.

    1994-07-01

    At Lawrence Berkeley Laboratory's (LBL) Advanced Light Source (ALS), three 4.6 m long undulators have been completed, tested and installed. A fourth is under construction. The completed undulators include two 5.0 cm period length, 89 period devices (U5.0s) which achieve a 0.85 T effective field at a 14 mm minimum gap and a 8.0 cm period length, 55 period device (U8.0) that reaches a 1.2 T effective field at a 14 mm minimum gap. The undulator under construction is a 10.0 cm period length, 43 period device (U10.0) that is designed to achieve 0.98 T at a 23 mm gap. Undulator magnetic gap variation (rms) is within 25 microns over the periodic structure length. Reproducibility of the adjustable magnetic gap has been measured to be within +/- 5 microns. Gap adjusting range is from 14 mm to 210 mm, which can be scanned in one minute. The 5.1 m long vacuum chambers are flat in the vertical direction to within 0.74 mm and straight in the horizontal direction to within 0.08 mm over the 4.6 m magnetic structure sections. Vacuum chamber base pressures after UHV beam conditioning are. in the mid 10 -11 Torr range and storage ring operating pressures with full current are in the low 10 -10 Torr range. Measurements show that the uncorrelated magnetic field errors are 0.23%, and 0.20% for the two U5.Os and the U8.0 respectively and that the field integrals are small over the 1 cm by 6 cm beam aperture. Device description, fabrication, and measurements are presented

  4. Trace element emissions from coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    Trace elements are emitted during coal combustion. The quantity, in general, depends on the physical and chemical properties of the element itself, the concentration of the element in the coal, the combustion conditions and the type of particulate control device used, and its collection efficiency as a function of particle size. Some trace elements become concentrated in certain particle streams following combustion such as bottom ash, fly ash, and flue gas particulate matter, while others do not. Various classification schemes have been developed to describe this partitioning behaviour. These classification schemes generally distinguish between: Class 1: elements that are approximately equally concentrated in the fly ash and bottom ash, or show little or no fine particle enrichment, examples include Mn, Be, Co and Cr; Class 2: elements that are enriched in the fly ash relative to bottom ash, or show increasing enrichment with decreasing particle size, examples include As, Cd, Pb and Sb; Class 3: elements which are emitted in the gas phase (primarily Hg (not discussed in this review), and in some cases, Se). Control of class 1 trace elements is directly related to control of total particulate matter emissions, while control of the class 2 elements depends on collection of fine particulates. Due to the variability in particulate control device efficiencies, emission rates of these elements can vary substantially. The volatility of class 3 elements means that particulate controls have only a limited impact on the emissions of these elements.

  5. REACTOR FUEL ELEMENTS TESTING CONTAINER

    Science.gov (United States)

    Whitham, G.K.; Smith, R.R.

    1963-01-15

    This patent shows a method for detecting leaks in jacketed fuel elements. The element is placed in a sealed tank within a nuclear reactor, and, while the reactor operates, the element is sparged with gas. The gas is then led outside the reactor and monitored for radioactive Xe or Kr. (AEC)

  6. LA CONFIGURACIÓN DE LA CIUDADANÍA EN LOS PROGRAMAS DE ESTUDIO DE LA EDUCACIÓN CÍVICA AL INICIAR EL SIGLO XXI: EL CASO DEL ELEMENTO POLÍTICO DE LA CIUDADANÍA (THE CITIZENSHIP CONFIGURATION ON THE PROGRAMS’ CIVIC EDUCATION STUDIES AT THE BEGINNING OF THE XXI CENTURY: THE CASE OF THE CITIZENSHIP’S POLITIC ELEMENT

    Directory of Open Access Journals (Sweden)

    Toruño Arguedas César

    2011-08-01

    Full Text Available Resumen:El artículo estudia la construcción del proyecto de ciudadanía a partir de un análisis de contenido del elemento político plasmado en los programas de estudio de Educación Cívica en el período 2000-2008. El proceso de selección de los contenidos, para lo cual se incluyó análisis de documentos y entrevistas a integrantes de las comisiones de reforma y revisión de los programas de estudio de la asignatura. A partir de una interrelación entre fundamentos curriculares, las circunstancias en que se desarrolla el proceso de selecci��n de contenidos y su análisis crítico se concluye que la configuración de la ciudadanía en los programas de estudio de Educación Cívica no responde a criterios curriculares elementales, se desarrolla dentro de procesos coyunturales y marcado por redes, explícitas o no, de poder y subjetividades, todo lo cual determina la selección de contenidos y la construcción del proyecto de ciudadanía oficialmente establecida en los programas de estudio.Abstract: The article examines of the citizenship project’s construction from the content study of the political element depicted on the programs’ civic education studies during the period 2000-2008. The selection process of the contents, for this, it was included documental analysis and interviews to the individuals that are part of the reform and review of the study programs’ civic education. From the interrelation between curricular basis, the circumstances on which it is developed the selection process of contents and the critical analysis, it can be concluded that the citizenship’s configuration on the programs on civic education studies does not answer to elemental curricular criteria. It is developed on in the context of the situation and marked by nets, explicit or not, of power and subjectivities. All this determines the content selection and the development of the citizenship’s project officially established in the study

  7. Accelerator vacuum system elements

    International Nuclear Information System (INIS)

    Sivokon', V.V.; Kobets, A.F.; Shvetsov, V.A.; Sivokon', L.V.

    1980-01-01

    Some elements of vacuum systems are investigated. Considerable attention has been given to the investigation into peculiarities in pumping out of a ionoguide for transportation of an accelerated charged particles beam the spread of which often attains a considerable length. The number of pumps over the ionoguide length is experimentally determined. It is shown that as a result of ionoguide warm-up the pumping out time is considerably reduced maximum permissible pressure is decreased by two orders and lesser rate of pump pumping out is required. The investigations have shown that when operating the ionoguide there is no necessity in setting up seals between the ionoguide and magnetodischarged pump. The causes of the phenomenon in which the pressure near the pump is greater than in the end of the ionoguide, are impurities carried in by the pump into the ionoguide volume and the pumping out capacity of the pressure converter

  8. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    1974-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed and has a metal liner disposed between the cladding and the nuclear fuel material and a high lubricity material in the form of a coating disposed between the liner and the cladding. The liner preferably has a thickness greater than the longest fission product recoil distance and is composed of a low neutron capture cross-section material. The liner is preferably composed of zirconium, an alloy of zirconium, niobium or an alloy of niobium. The liner serves as a preferential reaction site for volatile impurities and fission products and protects the cladding from contact and reaction with such impurities and fission products. The high lubricity material acts as an interface between the liner and the cladding and reduces localized stresses on the cladding due to fuel expansion and cracking of the fuel

  9. Probabilistic fracture finite elements

    Science.gov (United States)

    Liu, W. K.; Belytschko, T.; Lua, Y. J.

    1991-05-01

    The Probabilistic Fracture Mechanics (PFM) is a promising method for estimating the fatigue life and inspection cycles for mechanical and structural components. The Probability Finite Element Method (PFEM), which is based on second moment analysis, has proved to be a promising, practical approach to handle problems with uncertainties. As the PFEM provides a powerful computational tool to determine first and second moment of random parameters, the second moment reliability method can be easily combined with PFEM to obtain measures of the reliability of the structural system. The method is also being applied to fatigue crack growth. Uncertainties in the material properties of advanced materials such as polycrystalline alloys, ceramics, and composites are commonly observed from experimental tests. This is mainly attributed to intrinsic microcracks, which are randomly distributed as a result of the applied load and the residual stress.

  10. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Obara, Hiroshi.

    1981-01-01

    Purpose: To suppress iodine release thereby prevent stress corrosion cracks in fuel cans by dispersing ferrous oxide at the outer periphery of sintered uranium dioxide pellets filled and sealed within zirconium alloy fuel cans of fuel elements. Constitution: Sintered uranium dioxide pellets to be filled and sealed within a zirconium alloy fuel can are prepared either by mixing ferric oxide powder in uranium dioxide powder, sintering and then reducing at low temperature or by mixing iron powder in uranium dioxide powder, sintering and then oxidizing at low temperature. In this way, ferrous oxide is dispersed on the outer periphery of the sintered uranium dioxide pellets to convert corrosive fission products iodine into iron iodide, whereby the iodine release is suppressed and the stress corrosion cracks can be prevented in the fuel can. (Moriyama, K.)

  11. Nuclear fuel element

    International Nuclear Information System (INIS)

    Hirama, H.

    1978-01-01

    A nuclear fuel element comprises an elongated tube having upper and lower end plugs fixed to both ends thereof and nuclear fuel pellets contained within the tube. The fuel pellets are held against the lower end plug by a spring which is supported by a setting structure. The setting structure is maintained at a proper position at the middle of the tube by a wedge effect caused by spring force exerted by the spring against a set of balls coacting with a tapered member of the setting structure thereby wedging the balls against the inner wall of the tube, and the setting structure is moved free by pushing with a push bar against the spring force so as to release the wedge effect

  12. Finite element modelling

    International Nuclear Information System (INIS)

    Tonks, M.R.; Williamson, R.; Masson, R.

    2015-01-01

    The Finite Element Method (FEM) is a numerical technique for finding approximate solutions to boundary value problems. While FEM is commonly used to solve solid mechanics equations, it can be applied to a large range of BVPs from many different fields. FEM has been used for reactor fuels modelling for many years. It is most often used for fuel performance modelling at the pellet and pin scale, however, it has also been used to investigate properties of the fuel material, such as thermal conductivity and fission gas release. Recently, the United Stated Department Nuclear Energy Advanced Modelling and Simulation Program has begun using FEM as the basis of the MOOSE-BISON-MARMOT Project that is developing a multi-dimensional, multi-physics fuel performance capability that is massively parallel and will use multi-scale material models to provide a truly predictive modelling capability. (authors)

  13. Heavy-element research

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    The status is reported of studies on the solid-state chemistry of the actinides and lanthanides, spectroscopy of actinide compounds, and dynamic chemical description of actinide elements in solution. Phase studies were done on Rb 2 UO 4 , K 2 UO 4 , Li 2 UO 4 , and Es 2 U 2 O 7 . The lithium neptunate (VI) system was investigated and the existence of Li 2 NpO 4 was established. In oxidation-reduction studies it was shown that Am(III) can be electrolytically oxidized to Am(IV) in strong H 3 PO 4 , but Cf(III) and Pr(III) do not oxidize. The low-temperature absorption spectrum of thin films of NpBr 3 was investigated. (U.S.)

  14. ELEMENTAL FORMS OF HOSPITALITY

    Directory of Open Access Journals (Sweden)

    Maximiliano Emanuel Korstanje

    2010-11-01

    Full Text Available Modern studies emphasized on the needs of researching the hospitality as relevant aspects of tourism and hospitality fields. Anyway, these approaches are inextricably intertwined to the industry of tourism and do not take seriously the anthropological and sociological roots of hospitality. In fact, the hotel seems to be a partial sphere of hospitality at all. Under this context, the present paper explores the issue of hospitality enrooted in the political and economic indo-European principle of free-transit which is associated to a much broader origin.  Starting from the premise etymologically hostel and hospital share similar origins, we follow the contributions of J Derrida to determine the elements that formed the hospitality up to date.

  15. Photo-switching element

    Energy Technology Data Exchange (ETDEWEB)

    Masaki, Yuichi

    1987-10-31

    Photo-input MOS transistor (Photo-switching element) cannot give enough ON/OFF ratio but requires an auxiliary condenser for a certain type of application. In addition, PN junction of amorphous silicon is not practical because it gives high leak current resulting in low electromotive force. In this invention, a solar cell was constructed with a lower electrode consisting of a transparent electro-conducting film, a photosensitive part consisting of an amorphous Si layer of p-i-n layer construction, and an upper metal electrode consisting of Cr or Nichrome, and a thin film transistor was placed on the solar cell, and further the upper metal electrode was co-used as a gate electrode of the thin film transistor; this set-up of this invention enabled to attain an efficient photo-electric conversion of the incident light, high electromotive force of the solar cell, and the transistor with high ON/OFF ratio. (3 figs)

  16. Discrete element simulation of internal stress in SiCp/aluminum ...

    African Journals Online (AJOL)

    SiCp / Al-Mg-Si matrix composite was prepared by pressureless Infiltration Process. By discrete element method, microcosmic two-dimensional numerical model of SiCp / Al matrix composites was established and the simulation of the size and distribution of micro-contact pressure and tension was performed from small load ...

  17. Elemental imbalance studies by INAA on extra neural tissues from amyotrophic lateral sclerosis patients

    International Nuclear Information System (INIS)

    Tandon, L.; Ehmann, W.D.

    1995-01-01

    Human kidney and liver tissues were studied for generalized elemental imbalances in amyotrophic lateral sclerosis (ALS) by instrumental neutron activation analysis (INAA). Iron was significantly increased (p<0.05) in ALS kidneys and Co and Fe (marginal, p<0.10) were increased in ALS liver compared with their respective controls. Mercury values were almost two-fold higher for ALS kidney and 17% higher for ALS liver as compared with their respective controls, However, the Hg data exhibited large variations and ALS-control differences were not significant. Data from the present study are discussed with reference to the role of metallothioneins (MT) in ALS, and a possible linkage between a free radical mediated mechanism and degeneration of cells in ALS is also explored. (author). 43 refs., 2 tabs

  18. Diffusion-induced quadrupole relaxation of 27Al nuclei in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at high temperatures

    International Nuclear Information System (INIS)

    Bottyan, L.; Beke, D.L.; Tompa, K.

    1983-01-01

    The temperature dependence of the laboratory frame spin-lattice relaxation time of 27 Al nuclei is measured in 5N Al and in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at 5.7 and 9.7 MHz resonance frequencies. The relaxation in pure aluminium is found to be purely due to the conduction electrons. An excess T 1 -relaxation contribution is detected in all Al-3d alloys investigated above 670 K. The excess relaxation rate is proportional to the impurity content and the temperature dependence of the excess contribution is of Arrhenius-type with an activation energy of (1.3 +- 0.3) eV for all of the investigated alloys. The relaxation contribution is found to be quadrupolar in origin and is caused by the relative diffusional jumps of solute atoms and Al atoms relatively far from the impurity. (author)

  19. Elemental Spatiotemporal Variations of Total Suspended Particles in Jeddah City

    Directory of Open Access Journals (Sweden)

    Mohammad W. Kadi

    2014-01-01

    Full Text Available Elements associated with total suspended particulate matter (TSP in Jeddah city were determined. Using high-volume samplers, TSP samples were simultaneously collected over a one-year period from seven sampling sites. Samples were analyzed for Al, Ba, Ca, Cu, Mg, Fe, Mn, Zn, Ti, V, Cr, Co, Ni, As, and Sr. Results revealed great dependence of element contents on spatial and temporal variations. Two sites characterized by busy roads, workshops, heavy population, and heavy trucking have high levels of all measured elements. Concentrations of most elements at the two sites exhibit strong spatial gradients and concentrations of elements at these sites are higher than other locations. The highest concentrations of elements were observed during June–August because of dust storms, significant increase in energy consumption, and active surface winds. Enrichment factors of elements at the high-level sites have values in the range >10~60 while for Cu and Zn the enrichment factors are much higher (~0–>700 indicating that greater percentage of TSP composition for these three elements in air comes from anthropogenic activities.

  20. Finite Element Method in Machining Processes

    CERN Document Server

    Markopoulos, Angelos P

    2013-01-01

    Finite Element Method in Machining Processes provides a concise study on the way the Finite Element Method (FEM) is used in the case of manufacturing processes, primarily in machining. The basics of this kind of modeling are detailed to create a reference that will provide guidelines for those who start to study this method now, but also for scientists already involved in FEM and want to expand their research. A discussion on FEM, formulations and techniques currently in use is followed up by machining case studies. Orthogonal cutting, oblique cutting, 3D simulations for turning and milling, grinding, and state-of-the-art topics such as high speed machining and micromachining are explained with relevant examples. This is all supported by a literature review and a reference list for further study. As FEM is a key method for researchers in the manufacturing and especially in the machining sector, Finite Element Method in Machining Processes is a key reference for students studying manufacturing processes but al...

  1. Wetting and interface interactions in the B4C/Al-Me (Me=Cu, Sn) systems

    International Nuclear Information System (INIS)

    Aizenshtein, M.; Froumin, N.; Dariel, M.P.; Frage, N.

    2008-01-01

    The wettability of B 4 C in contact with non-carbide and non-boride forming liquid metals (such as Cu or Sn) has been the subject of several studies. These metals do not wet boron carbide unless a reactive element is added to the melt. The present study is concerned with the addition of Al which completes the series of reactive elements added to the non-wetting metals. While Si represents the elements that form stable carbides and Ti represents the elements that form stable borides, Al belongs to the group of elements that form ternary borocarbides. The wetting experiments in the B 4 C/(Me-Al, Me=Cu, Sn) systems have shown that a ternary product, namely Al 8 B 4 C 7 was formed at the interface and that wetting is governed by the thermodynamic properties of the binary liquid system

  2. Dynamic globularization of a-phase in Ti6Al4V alloy during hot compression

    CSIR Research Space (South Africa)

    Mutombo, K

    2013-12-01

    Full Text Available composition dependence of the martensite start temperature (Ms) has been done for Ti-Fe, Ti-Cr, Ti-Mo, Ti-V, Ti-Nb, Ti-Zr and Ti-Al alloys [1], [2]. The beneficial effect on the formation of hexagonal-structured martensite (α′) of Al, Mn, Cr, Sn and Fe... alloying elements, has been discussed by Lin et al [4]. However, the formation of the orthorhombic-structured martensite (α′′) which is favoured by elements such as Nb, Mo, Zr, W and V (strong β stabilizers) or H (a strong β stabilizer), has been reported...

  3. Annex 5 - Fabrication of U-Al alloy

    International Nuclear Information System (INIS)

    Drobnjak, Dj.; Lazarevic, Dj.; Mihajlovic, A.

    1961-01-01

    Alloy U-Al with low content of aluminium is often used for fabrication of fuel elements because it is stable under moderate neutron flux density. Additionally this type of alloys show much better characteristics than pure uranium under reactor operating conditions (temperature, mechanical load, corrosion effect of water). This report contains the analysis of the phase diagram of U-Al alloy with low content of aluminium, applied procedure for alloying and casting with detailed description of equipment. Characteristics of the obtained alloy are described and conclusions about the experiment and procedure are presented [sr

  4. High temperature oxidation behavior of TiAl-based intermetallics

    International Nuclear Information System (INIS)

    Stroosnijder, M.F.; Sunderkoetter, J.D.; Haanappel, V.A.C.

    1996-01-01

    TiAl-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 C. In the present contribution some general aspects of high temperature oxidation of TiAl-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behavior of such materials

  5. Der Wortschatz als "Wahrheitsvermittler" im außenpolitischen Pressekommentar

    Directory of Open Access Journals (Sweden)

    Vida Jesenšek

    1998-12-01

    Full Text Available Bekannterweise weist die ausgewählte journalistische Textsorte eine spezifische textuelle Struktur auf; ihre inhaltliche (evaluative und intentionale Komponente sind zunächst in Kürze zu erläutern. Es zeigt sich, daß die Bewertung als obligatorisches Element eines Kommentartextes textstrukturell und stilistisch-pragmatisch bedingt ist und daß sie im Prinzip mittels Lexik realisiert wird. Das Funktionieren der Lexik als Bewertungsträger wird anschließend aufgrund einer exemplarischen Fallanalyse dargestellt, wobei hauptsächlich Zusammenhänge zwischen textstrukturellen Besonderheiten der Kommentartexte und stilistisch-pragmatischen Eigenschaften der Lexik interessieren.

  6. Effects of combined additions of Sr and AlTiB grain refiners in hypoeutectic Al-Si foundry alloys

    International Nuclear Information System (INIS)

    Lu, L.; Dahle, A.K.

    2006-01-01

    Strontium is the most widely used and a very effective element for modifying the morphology of eutectic silicon, while Ti and B are commonly present in the commercial grain refiners used for Al-Si alloys. Systematic studies on the effects of combined additions of Sr and different AlTiB grain refiners on the Al + Si eutectic and primary aluminium solidification have been performed. While slight coarsening of both eutectic Si and primary aluminium grains occurs during holding, no obvious interactions are observed between Sr and AlTiB grain refiners when the addition level of grain refiners is low. As a result, a well-modified and grain refined structure was obtained. However, strong negative interactions between Sr and Al1.5Ti1.5B were observed as the addition level of the grain refiner increases. It was found that these interactions have a much more profound impact on the eutectic solidification than the primary Al solidification. The melt treated with combined additions of Sr and Al1.5Ti1.5B still shows good grain refinement efficiency even after losing its modification completely. The mechanism responsible for such negative interactions is further discussed

  7. Effects of combined additions of Sr and AlTiB grain refiners in hypoeutectic Al-Si foundry alloys

    Energy Technology Data Exchange (ETDEWEB)

    Lu, L. [CSIRO Minerals, P.O. Box 883, Kenmore, Qld. 4069 (Australia)]. E-mail: Liming.Lu@csiro.au; Dahle, A.K. [CRC for Cast Metals Manufacturing, Division of Materials, School of Engineering, University of Queensland, Brisbane, Qld. 4072 (Australia)

    2006-11-05

    Strontium is the most widely used and a very effective element for modifying the morphology of eutectic silicon, while Ti and B are commonly present in the commercial grain refiners used for Al-Si alloys. Systematic studies on the effects of combined additions of Sr and different AlTiB grain refiners on the Al + Si eutectic and primary aluminium solidification have been performed. While slight coarsening of both eutectic Si and primary aluminium grains occurs during holding, no obvious interactions are observed between Sr and AlTiB grain refiners when the addition level of grain refiners is low. As a result, a well-modified and grain refined structure was obtained. However, strong negative interactions between Sr and Al1.5Ti1.5B were observed as the addition level of the grain refiner increases. It was found that these interactions have a much more profound impact on the eutectic solidification than the primary Al solidification. The melt treated with combined additions of Sr and Al1.5Ti1.5B still shows good grain refinement efficiency even after losing its modification completely. The mechanism responsible for such negative interactions is further discussed.

  8. Field ion microscopy and 3-D atom probe analysis of Al3Zr particles in 7050 Al alloy

    International Nuclear Information System (INIS)

    Sha, G.; Cerezo, A.

    2004-01-01

    Full text: For high strength 7xxx series Al alloys, Zr is an important trace alloy element which is often added to optimise properties, having effects such as refining grain size, inhibiting recrystallization, and improving stress corrosion cracking resistance and quench sensitivity. In addition, it has been reported recently that Zr addition also has a significant influence on early stage ageing behaviour of a 7xxx series Al alloy. Zr equilibrium solubility in solid Al is extremely low. After solution or ageing treatment, most Zr is present as small spherical Ai 3 Zr dispersoids approximately 20 nm in diameter, distributed at grain boundaries as well as within the Al matrix. The crystallographic nature of intermetallic phase Al 3 Zr has been well studied in the literatures. So far, no direct measurement of the chemistry of the Al 3 Zr particles in 7xxx series Al alloys has been published. It is unclear if there is significant Zn, Mg or Cu included in the particles. In this research, 3DAP has been employed for the first time to investigate ionisation behaviour of Al 3 Zr particles and determine the chemistry of the particles in 7050 Al alloy. Using field ion microscopy, the local evaporation radius of the Al 3 Zr particle has been measured to be equivalent to 36 nm for a 10 kV tip, less than the equivalent tip radius for the Al matrix of ∼68 nm. Using the matrix Al evaporation field (19 V/nm) as a reference, this allows the evaporation field of Al 3 Zr to be calculated as 35 V/nm, the same as the field calculated for evaporation of Al as Al 2+ (35 V/nm), and that of Zr as Zr 3+ (35 V/nm). This result is consistent with Al 2+ and Zr 3+ being the main species observed in the mass spectrum during analysis of Al 3 Zr particles. Using 3DAP, the chemical compositions of Al 3 Zr particles are determined to be 64.8∼67.7 at% Al, 23.6∼24.8 at% Zr, 6.9∼9.1 at% Zn, 0.4∼0.7 at% Cu, 0.5∼1.2 at% Mg, with a (Al+Zn)/Zr ratio close to 3. Choice of specimen temperature of

  9. Acid-base properties of complexes of 3 group elements with tetra-4-tert. butylphthalocyanine. [Elements: Al, Ga, In, Sc

    Energy Technology Data Exchange (ETDEWEB)

    Borovkov, N Yu; Akopov, A S

    1987-01-01

    Step-like constants of pKn complex ionization of In and Sc with tetra-4-tert.butylphthalocyanine in CH/sub 3/COOH-H/sub 2/SO/sub 4/ and B-CH/sub 3/COOH-H/sub 2/SO/sub 4/, where B is antipyrine or urea are determined. They have the next values at n equalling 1, 2, 3, 4: +2.70+-0.30; -0.26+-0.09; -3.70+-0.20; -6.10+-0.20 for HOIn phthalocyanine substituted correspondingly. Effect of the methane atom nature on the basicity of phthalocyanine nitrogen mesonic atoms is considered. Using the conductometry method, it is established that phthalocyanines in concentrated H/sub 2/SO/sub 4/ form both completely protonated shapes and contact ion pairs.

  10. Granitoids of South Korea and Southwest Japan. Trace element evidence regarding their differentiation

    International Nuclear Information System (INIS)

    Tsusue, Akio; Mizuta, Toshio; Tamai, Tadaharu.

    1994-01-01

    Although we have already published our trace element data for granitoids of South Korea and Southwest Japan, and we have interpreted REE patterns and Ba, Rb and Sr relationships of the granitoids (Tsusue et al., 1986, 1987a, 1987b, 1988), we intend to review briefly the trace element data of South Korea and Southwest Japan in this report. (J.P.N.)

  11. PIXE and neutron activation analysis: intercomparison in the elemental concentration of airborne particulate matter

    International Nuclear Information System (INIS)

    Cassorla, V.; Rojas, X.; Gras, N.; Chuaqui, L.; Dinator, M.I.; Morales, J.R.; Llona, F.; Romo-Kroeger, C.

    1993-01-01

    Two nuclear analytical techniques, neutron activation analysis (NAA) and proton induced X-ray emission (PIXE), were used to determine major and trace elements in airborne particulate matter collected during the first fortnight of June 1991 at the La Reina Nuclear Center. NAA detected the presence of 15 elements in the samples. PIXE, for the same samples, allowed the detection of 12 elements. The elements determined by both techniques were Al, Ca, Mn, Fe, Cu, and Zn. A good correlation between results for these elements for each of the two techniques was demonstrated. (author)

  12. The Chemistry of Superheavy Elements

    CERN Document Server

    Schädel, M

    2003-01-01

    The chemistry of transactinide or superheavy elements has reached element 108. Preparations are under way to leap to element 112 and beyond. The current status of this atom-at-a-time chemical research and its future perspectives are reviewed from an experimental point of view together with some of the interesting results from n -rich nuclides near and at the N=162 neutron shell. Experimental techniques and important results enlightening typical chemical properties of elements 104 through 108 are presented in an exemplary way. From the results of these experiments it is justified to place these elements in the Periodic Table of the Elements in to groups 4 through 8, respectively. However, mainly due to the influence of relativistic effects, it is no longer possible to deduce detailed chemical properties of these superheavy elements simply from this position.

  13. Transplutonium elements - a literature survey

    International Nuclear Information System (INIS)

    Sivaramakrishnan, C.K.; Jadhav, A.V.

    1974-01-01

    The report surveys reported work on the discovery of transplutonium elements and their production through various methods like bombardment of heavy elements with charged ions, successive neutron captures on heavy elements in reactors and multiple neutron captures by heavy elements during nuclear explosions. Estimated yields of transplutonium elements in special targets irradiated in reactors, and also as byproducts from spent power reactor fuels are quoted. Various chemical procedures adopted for recovery of these elements from irradiated target and also from power reactor fuel reprocessing streams are described. A brief survey of shielded facilities available at various centres for transplutonium programmes is also included. Major uses of some of these heavy elements are described. (author)

  14. Deformation mechanisms of nanotwinned Al

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xinghang [Texas A & M Univ., College Station, TX (United States)

    2016-11-10

    The objective of this project is to investigate the role of different types of layer interfaces on the formation of high density stacking fault (SF) in Al in Al/fcc multilayers, and understand the corresponding deformation mechanisms of the films. Stacking faults or twins can be intentionally introduced (via growth) into certain fcc metals with low stacking fault energy (such as Cu, Ag and 330 stainless steels) to achieve high strength, high ductility, superior thermal stability and good electrical conductivity. However it is still a major challenge to synthesize these types of defects into metals with high stacking fault energy, such as Al. Although deformation twins have been observed in some nanocrystalline Al powders by low temperature, high strain rate cryomilling or in Al at the edge of crack tip or indentation (with the assistance of high stress intensity factor), these deformation techniques typically introduce twins sporadically and the control of deformation twin density in Al is still not feasible. This project is designed to test the following hypotheses: (1) Certain type of layer interfaces may assist the formation of SF in Al, (2) Al with high density SF may have deformation mechanisms drastically different from those of coarse-grained Al and nanotwinned Cu. To test these hypotheses, we have performed the following tasks: (i) Investigate the influence of layer interfaces, stresses and deposition parameters on the formation and density of SF in Al. (ii) Understand the role of SF on the deformation behavior of Al. In situ nanoindentation experiments will be performed to probe deformation mechanisms in Al. The major findings related to the formation mechanism of twins and mechanical behavior of nanotwinned metals include the followings: 1) Our studies show that nanotwins can be introduced into metals with high stacking fault energy, in drastic contrast to the general anticipation. 2) We show two strategies that can effectively introduce growth twins in

  15. Deformation mechanisms of nanotwinned Al

    International Nuclear Information System (INIS)

    Zhang, Xinghang

    2016-01-01

    The objective of this project is to investigate the role of different types of layer interfaces on the formation of high density stacking fault (SF) in Al in Al/fcc multilayers, and understand the corresponding deformation mechanisms of the films. Stacking faults or twins can be intentionally introduced (via growth) into certain fcc metals with low stacking fault energy (such as Cu, Ag and 330 stainless steels) to achieve high strength, high ductility, superior thermal stability and good electrical conductivity. However it is still a major challenge to synthesize these types of defects into metals with high stacking fault energy, such as Al. Although deformation twins have been observed in some nanocrystalline Al powders by low temperature, high strain rate cryomilling or in Al at the edge of crack tip or indentation (with the assistance of high stress intensity factor), these deformation techniques typically introduce twins sporadically and the control of deformation twin density in Al is still not feasible. This project is designed to test the following hypotheses: (1) Certain type of layer interfaces may assist the formation of SF in Al, (2) Al with high density SF may have deformation mechanisms drastically different from those of coarse-grained Al and nanotwinned Cu. To test these hypotheses, we have performed the following tasks: (i) Investigate the influence of layer interfaces, stresses and deposition parameters on the formation and density of SF in Al. (ii) Understand the role of SF on the deformation behavior of Al. In situ nanoindentation experiments will be performed to probe deformation mechanisms in Al. The major findings related to the formation mechanism of twins and mechanical behavior of nanotwinned metals include the followings: 1) Our studies show that nanotwins can be introduced into metals with high stacking fault energy, in drastic contrast to the general anticipation. 2) We show two strategies that can effectively introduce growth twins in

  16. Partitioning of elements during coal combustion and leaching experiments

    Energy Technology Data Exchange (ETDEWEB)

    Wang Wen-feng; Qin Yong; Song Dang-yu; Wang Jun-yi [China University of Mining & Technology, Xuzhou (China). School of Resources and Earth Science

    2009-04-15

    The mineral component and content of sulfur and 42 major and trace elements of the feed coal, fly and bottom ashes collected from Shizuishan coal-fired power plant, Ningxia, China were analyzed using AFS, INAA, ICP-MS, ICP-AES, XRD. Based on the coal combustion and leaching experiments, the partitioning of these elements during coal combustion and the leaching behavior of the 11 potentially hazardous elements, including As, Cd, Co, Cr, Hg, Mo, Ni, Pb, Se, Th and U were investigated. The results show that the distribution of elements in the fly and bottom ashes is controlled by their volatilities and modes of occurrence in the coal. The degree of volatilization of elements may be mainly associated with boiling/melting points of these elements and their compounds. The elements easily volatilized, organically bound or associated with sub-micrometer and nano minerals (e.g. Al and Na) tend to be enriched in the fine fractions of fly ash, and most elements do not vaporize which are approximately equally partitioned in the fly and bottom ashes. The emission rates of As, Cr, K, Mg, Mn, Mo, Pb, Sb, and Zn are notably influenced by the temperature ranging from 877 to 1300{sup o}C. The leaching behavior of elements depend significantly on their geochemical properties and modes of occurrence. The elements with a low degree of volatilization are not easily leached, while volatile elements easily leached under the acid conditions. Arsenic, B Br, Cd, Cu, Hg, Pb, S, Sb and Se show a higher emission rate during coal combustion, and the leached concentrations of Cd, Co, Mo, Ni and U in the acid media exceed their limited concentrations recommended in relevant environment quality standards for water, which will harm the environment. 32 refs., 4 figs., 4 tabs.

  17. PIXE trace element analysis of a selection of wines

    International Nuclear Information System (INIS)

    Houdayer, A.; Hinrichsen, P.F.; Martin, J.P.; Belhadfa, A.

    1987-01-01

    The University of Montreal EN Tandem accelerator and a Si (Li) X-ray detector were used for a PIXE (Proton Induced X-ray emission) trace element analysis of a selection of wines. Quantitative measurements of the concentrations of the sixteen trace elements Na, Mg, Al, Si, P, S, Cl, K, Ca, Cr, Mn, Fe, Co, Cu, Zn, and Br were made. To optimize the sensitivity, spectra were recorded at 1.0 MeV proton energy for elements with Z 19. The absolute concentrations of the trace elements were determined by doping the samples of wine with 1000 ppm of vanadium for the 1.0 MeV bombardments, and 1000 ppm of yttrium for the 3.0 MeV irradiations. The targets were prepared by depositing a few microliters of the wine onto a Nuclepore filter

  18. Elemental content in ground and soluble/instant coffee

    International Nuclear Information System (INIS)

    Vega-Carrillo, H.R.; Manzanares-Acuna, E.; Iskander, F.Y.

    2002-01-01

    The concentration of thirty-four elements in twelve coffee brands has been measured using instrumental neutron activation analysis. The samples investigated included four brands of commercially available ground coffee and eight brands of soluble/instant coffee. The elements measured were Al, As, Ba, Ca, Ce, Co, Cr, Cs, Dy, Eu, Fe, Gd, Hf, K, La, Lu, Mg, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Tm, U, V, Yb and Zn. Twenty four elements were found to be below the detection limit in one or more samples. These elements were Ce, Cr, Fe, V, As, Eu, Ba, Dy, Gd, Hf, La, Lu, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Yb, Tm, and U. (author)

  19. Transformasi Budaya Dalam Al-Qur’an

    Directory of Open Access Journals (Sweden)

    Nurul Hakim

    2016-12-01

    Full Text Available Abstract: Everyone wants to have prosperity in their life. But in the point of fact, not all people are able to fulfill their fancy. As the result, such question rises "Why do all fancies have not been fulfilled?" To overcome that problem, Al-Qur’an offers a solution that discusses about concept of fulfillment. This concept draws the movement of human mindset and it called as Cultural transformation. Moreover, mindset is the basic fundamental and its fundamental affects other aspects of human life. Furthermore, they are four terms of culture such cultural values, cultural systems, social system, physical culture (elements of physical cultures.  While cultural values are defined as vantage of life, priority, time allotment, human point of views, and natural views.

  20. KONSEP MᾹQᾹṢID AL-SYᾹRĪAH MENURUT ṬᾹHᾹ JᾹBIR AL-‘ALWᾹNĪ

    Directory of Open Access Journals (Sweden)

    Chasnak Najidah

    2017-03-01

    Full Text Available One discourse which is receiving considerable attention from scholars of Islam is about the objectives of Islamic law (maqasid al-shari'ah. Taha Jabir al-'Alwānī as one reviewer of Maqasid al-shari'ah contemporary formulate the concept of maqasid al-shari'ah different from previous scholars. This article describes the concept of maqasid al-shari'ah by Taha Jabir al-'Alwānī. According to him, there are three levels of hierarchical of Maqasid al-Sharia. The highest value of maqasid al-shari'ah says is what he describes as al-Maqasid al-'ulyā al-Hakimah (intentions of the highest shari'ah and a legal basis, which consists of three main elements, namely al-Tawhid ( Onesess of God, al-Tazkiyah (purification and al-'umrān (prosperity. The position of the second al-shari'ah Maqasid are universal values such as justice, freedom, and equality. While the third position is the formulation of the previous scholars regarding maqasid al-shari'ah consisting of ḍarūriyyat, ḥājiyyāt, and taḥsīniyyāt. In terms of methodological, Taha Jabir al-'Alwānī basing the new system for Maqasid al-syarī'ahnya on the methods of al-jam'u Baina al-qirā'atain, a reading of the two entities: the revelation of God and the universe. With this basis, he argues that the maqasid al-shari'ah formulations are qaṭ'ī, so it can be a reference to the scholars in solving the problems of contemporary law.   [Salah satu diskursus yang mendapat perhatian cukup besar dari para akademisi Islam adalah seputar tujuan-tujuan hukum islam  (maqāṣid al-syarī'ah. Ṭāhā Jābir al-‘Alwānī sebagai salah satu ulama pengkaji maqāṣid asy-syarī’ahkontemporer merumuskan konsep maqāṣid asy-syarī’ahyang berbeda dari ulama sebelumnya. Artikel ini mendeskripsikan konsep maqāṣid asy-syarī’ahmenurut Ṭāhā Jābir al-‘Alwānī. Menurutnya, ada tiga tingkatan hierarkis maqāṣid al-syarī'ah. Nilai tertinggi maqāṣid asy-syarī’ahmenurutnya adalah apa

  1. Constructional Efficiency in Al_Ahwaar Traditional Architecture

    Directory of Open Access Journals (Sweden)

    Usama Abdul-Mun'em Khuraibet

    2016-03-01

    Full Text Available Constructional Efficiency in architecture in general is one of the most important standard success for any structure and a measure of its continuity and relevance across time and space. Given the importance of Al-Ahwaar environment that owned the spatial, environmental, economic and social elements had a prominent impact in creation of architecture patterns form to create special architectural and structural environment, which had many qualities and ingredients that contributed to its continuity and existence over the years. From the premise that man and his environment is the main goal to any architectural style, Thus the research problem focusing on the lack of clarity of the previous literatures in its studies for the role of architectural styles in Al-Ahwaar in achieving constructional efficiency, despite the large number of studies on Al-Ahwaar architecture but it is mostly marked by non-clarity and lack in the constructional and technical aspects, Therefore, the research goal focusing on clarification of the impact of the techniques that used in formations Al_Ahwaar traditional architecture in order to reach to the constructional efficiency in various aspects such as technical, material, economical, and expressional. Assuming that achieving to the constructional efficiency at Al-Ahwaar traditional architecture depends on its characteristics and elements that contributed to the continuity of their patterns across time. The research depended on analytical method of a model of traditional architecture in Al-Ahwaar to reach those goals, as the study of these items aims to deepen the understanding of the designer to the requirements of each component in order to achieve integration together. These components must not conflict with each other, but it must be integrated during and after the design process until it comes out as a creative of architectural destination. al-ahwaar architecture, constructional efficiency, technical and material

  2. Interface behaviour of Al2O3/Ti joints produced by liquid state bonding

    International Nuclear Information System (INIS)

    Lemus R, J.; Guevara L, A. O.; Zarate M, J.

    2014-08-01

    The main objective of this work was to determine various aspects during brazing of Al 2 O 3 samples to commercially titanium alloy grade 4 with biocompatibility properties, using a Au-foil as joining element. Al 2 O 3 ceramic was previously produced by sintering of powder cylindrical shape at 1550 grades C for 120 minutes. Previously to joining experiments, the surface of Al 2 O 3 samples were coating, by chemical vapor depositions (CVD) process, with a Mo layer of 2 and 4 μm thick and then stacked together with the Ti samples. Joining experiments were carried out on Al 2 O 3 -Mo/Au/Ti combinations at temperature of 1100 grades C using different holding times under vacuum atmosphere. The experimental results show a successful joining Mo-Al 2 O 3 to Ti. Analysis by scanning electron microscopy (Sem) revealed that joining of Al 2 O 3 to metal occurred by the formation of a homogeneous diffusion zone with no interfacial cracking or porosity at the interface. Results by electron probe micro analysis (EPMA) of Al 2 O 3 -Mo/Au/Ti combinations revealed that Mo traveled inside the joining elements and remained as solid solutions, however during cooling process Mo had a tendency to stay as a precipitate phase and atomic distributions of elements show a concentration line of Mo inside the joining element Au. On the other hand, well interaction of Ti with Au form different phases; like Ti 3 Au and Ti Au. (author)

  3. SANANDO AL SANADOR

    Directory of Open Access Journals (Sweden)

    Juan Pablo Acuña, Dr.

    2017-09-01

    Full Text Available RESUMEN: La dependencia o adicción a sustancias de uso profesional es un problema que puede afectar gravemente a médicos de diferentes especialidades. En la anestesiología hay mayor riesgo de dependencia a opioides e hipnóticos que en otras especialidades y puede llegar a afectar al 1% de los médicos anestesiólogos.La fisiopatología del trastorno por uso de sustancias tiene hechos comunes para diferentes drogas. Interactúan la vulnerabilidad genética y factores psicosociales como predisponentes y los efectos psicobiológicos de la sustancia como factor gatillante. En el caso de los anestesiólogos, la sustancia se encuentra en el lugar de trabajo y por lo tanto, el individuo está constantemente expuesto.Una disfunción previa del sistema de recompensa en el circuito mesocorticolímbico o causada por la exposición a la sustancia adictiva es la piedra central de la neurobiología de las adicciones. Los opioides, anfetaminas, canabinoides, alcohol y nicotina, son algunas de las sustancias exógenas que activan el circuito y causan inicialmente un efecto hedónico que reforzará la conducta por repetir la experiencia. Con el tiempo la interacción con la droga será para evitar los síntomas de abstinencia.Dada la exposición laboral de los anestesiólogos, es necesario prevenir, detectar y tratar precozmente a quienes están abusando de sustancias durante su ejercicio profesional.Por las características de estos fármacos, aspectos psicológicos especiales de los médicos y el contexto laboral se hace necesario un tratamiento especializado y en anestesiólogos la reinserción laboral debe ser un proceso controlado, gradual y con un seguimiento prolongado. SUMMARY: Prescription drugs dependence seriously impairs doctors from differents fields of medicine. Anesthesiology has greater risk than other specialties to opioids and hypnotics dependence, with prevalence up to 1%.Substances use disorder has common mechanisms of disease regardless

  4. Determination of trace elements in chewing gum by neutron activation analysis

    International Nuclear Information System (INIS)

    Dietz, M.L.

    1990-01-01

    Six trace elements of nutritional or toxicological interest (Al, Ca, Cl, Mn, Na and Sr) were determined in three different brands of chewing gum by instrumental neutron activation analysis. For the particular brands of gum examined, none of the detected elements was found to be present at a level representing a substantial contribution to the total dietary intake of the element for an American adult. (author) 11 refs.; 3 tabs

  5. Polyisocyanurate systems for insulating and sandwich elements; Polyisocyanurat-Systeme fuer Daemm- und Sandwichelemente

    Energy Technology Data Exchange (ETDEWEB)

    Malotki, P. von [Elastogran GmbH, Lemfoerde (Germany)

    2000-07-01

    PUR rigid foam plates are laminated with flexible Al films, paper or glass non-wovens, or may be processed into sandwich elements with metallic top-layers via coil-coating. Dependence of heat insulation efficiency, dimensional stability and fire behavior of the foam on chemical composition and the blowing agents is considered and compared with polyisocyanurate foams. Recipes for the production of PIR heat insulation elements and sandwich elements are given.

  6. Essential and toxic elements in seaweeds for human consumption.

    Science.gov (United States)

    Desideri, D; Cantaluppi, C; Ceccotto, F; Meli, M A; Roselli, C; Feduzi, L

    2016-01-01

    Essential elements (K, Ca, P, S, Cl, Mn, Fe, Cu, Zn, Ni, Br, and I) and nonessential or toxic elements (Al, Ti, Si, Rb, Sr, As, Cd, Sn, and Pb) were determined by energy-dispersive polarized x-ray fluorescence spectrometry in 14 seaweeds purchased in local specialty stores in Italy and consumed by humans. The differences in elements between the algae species reached up to 2-4 orders of magnitude. Lithothamnium calcareum showed the highest levels of Ca, Al, Si, Fe, and Ti. Palmaria palmata showed the highest concentrations of K, Rb, and Cl. The highest content of S was in Chondrus crispus. Laminaria digitata contained the highest concentrations of total As, Cd, Sn, Br, and I. The highest concentration of Zn was in Chlorella pyrenoidosa. Ulva lactuca displayed the highest levels of Cu, Ni, Mn, and Pb. Iodine levels ranged from 3.4 in Chlorella pyrenoidosa to 7316 mg/kg(dry) in Laminaria digitata. The nutrimental importance of essential elements was assessed using nutritional requirements. The results showed that the consumption of algae might serve as an important source of the essential elements. Health risk due to the toxic elements present in seaweed was estimated using risk estimators. Total As, Cd, and Pb concentrations ranged from <1 to 67.6, to 7.2 and to 6.7 mg/kg(dry) respectively; therefore, their contribution to total elemental intake does not appear to pose any threat to the consumers, but the concentrations of these elements should be controlled to protect the consumer against potential adverse health risks.

  7. EAF optimal managing elements

    Science.gov (United States)

    Ioana, A.; Constantin, N.; Dragna, E. C.

    2017-01-01

    Electric Arc Furnaces (EAF) is an important and complex aggregate. We present elements of EAF operating efficiency. The reliability of the EAF is mainly determined by electric circuit reliability and especially of the transformator of the furnace. This due to the fact that, in an electric steel plant, the objective „24 tapping/day” involves. Due to the complexity of the process, the EAF operation needs a computer usage and, in his componence, it must have two independent calculation units (UC1) and (UC2). Based on these two input sets (Σi1) and ((Σi2), the calculation unit (UC1) builds the general operation procedure based on mathematical methods. For that purpose, there are used the results of the 5 mathematical methods: the mathematical model to write-off the function objective (M.F.O.); the mathematical model of calculating the charge (M.C.C.); the mathematical model of conducting the effective melt (M.C.M.); the mathematical model of reheating the charge (M.R.C.); the mathematical model of blasting the reactive dusts (M.B.R.D.).

  8. Nuclear fuel element

    International Nuclear Information System (INIS)

    Armijo, J.S.

    1977-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed which has a composite cladding having a substrate, a metal barrier metallurgically bonded to the inside surface of the substrate and an inner layer metallurgically bonded to the inside surface of the metal barrier. In this composite cladding, the inner layer and the metal barrier shield the substrate from any impurities or fission products from the nuclear fuel material held within the composite cladding. The metal barrier forms about 1 to about 4 percent of the thickness of the cladding and is comprised of a metal selected from the group consisting of niobium, aluminum, copper, nickel, stainless steel, and iron. The inner layer and then the metal barrier serve as reaction sites for volatile impurities and fission products and protect the substrate from contact and reaction with such impurities and fission products. The substrate and the inner layer of the composite cladding are selected from conventional cladding materials and preferably are a zirconium alloy. Also in a preferred embodiment the substrate and the inner layer are comprised of the same material, preferably a zirconium alloy. 19 claims, 2 figures

  9. Neutron absorbing element

    International Nuclear Information System (INIS)

    Kasai, Shigeo.

    1991-01-01

    The present invention concerns a neutron absorbing element of a neutron shielding member used for an LMFBR type reactor. The inside of a fuel can sealed at both of the upper and the lower ends thereof with plugs is partitioned into an upper and a lower chambers by an intermediate plug. A discharging hole is disposed at the upper end plug, which is in communication with the outside. A communication tube is disposed at the intermediate end plug and it is in communication with the lower chamber containing B 4 C pellets. A cylindrical support member having three porous plugs connected in series is disposed at the lower surface of the discharging hole provided at the upper end plug. Further, the end of the discharging hole is sealed with high temperature solder and He atmosphere is present at the inside of the fuel can. With such a constitution, the supporting differential pressure of the porous plugs can be made greater while discharging He gases generated from B 4 C to the outside. Further, the porous plugs can be surely wetted by coolants. Accordingly, it is possible to increase life time and shorten the size. (I.N.)

  10. Chemistry of transuranium elements

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    The half-wave amalgamation potential of No (element 102) was determined. Studies on the preparation and properties of Cf are reported; previously reported results on Es were confirmed. The heat of solution of Bk was measured. Spectroscopic and x-ray diffraction studies of Es-253 bromides are reported. Salicylate complexes with Sm(III), Am(III), Th(IV), and U(IV)O 2 were prepared; crystal data are given. Results of studies on the effect of secondary bonds on the strength of O double bond Np double bond O bonds are reported. The M series x rays of Np were measured. Anomalous spin--orbit splitting of the 4f level in the actinide series is reported. Progress is reported in studies on the Cf oxide system for oxygen pressures up to 760 mm and temperatures between 25 and 1000 0 C, as well as structural parameters of transplutonium oxysulfates and oxysulfides and actinide and lanthanide hydroxides. The electron paramagnetic resonance spectrum of 253 Es 2+ was observed in the cubic monocrystal hosts BaF 2 and SrCl 2

  11. Adhesive and tribocorrosive behavior of TiAlPtN/TiAlN/TiAl multilayers sputtered coatings over CoCrMo

    Science.gov (United States)

    Canto, C. E.; Andrade, E.; Rocha, M. F.; Alemón, B.; Flores, M.

    2017-09-01

    The tribocorrosion resistance and adherence of multilayer coatings of TiAlPtN/TiAlN/TiAl synthesized by PVD reactive magnetron sputtering over a CoCrMo alloy substrate in 10 periods of 30 min each were analyzed and compared to those of the substrate alone and to that of a TiAlPtN single layer coating of the same thickness. The objective of the present work was to create multilayers with different amounts of Pt in order to enhance the tribocorrosion resistance of a biomedical alloy of CoCrMo. Tribocorrosion tests were performed using Simulated Body Fluid (SBF) at typical body temperature with a tribometer in a pin on disk test. The elemental composition and thickness of the coating which behave better at the tribocorrosion tests were evaluated by means of RBS (Rutherford Backscattering Spectroscopy) IBA (Ion Beam Analysis) technique, using an alpha particles beam of 1.8 MeV, before and after the reciprocating motion in the tribocorrosion test. In order to simulate the elemental profile of the samples, the SIMNRA simulation computer code was used. Measurements of the adhesion of the coatings to the substrate were carried on by means of a scratch test using a tribometer. By taking micrographs of the produced tracks, the critical loads at which the coatings are fully separated from the substrate were determined. From these tests it was observed that a coating with 10 min of TiAlPtN in a TiAlPtN/TiAl period of 30 min in multilayers of 10 periods and with an average thickness of 145 nm for the TiAlPtN nanolayers had the best tribocorrosion resistance behavior, compared to that of the CoCrMo alloy. The RBS experiments showed a reduction of the thickness of the films along with some loss of the multilayer structure after the reciprocating motion. The adhesion tests indicated that the multilayer with the average TiAlPtN thickness of 145 nm displayed the highest critical load. These results indicate a high correlation between the adherence and the tribocorrosion behavior.

  12. Determination of specific concentration variations of atmospheric trace elements in precipitation as a method for the estimation of spatial deposition into the soil by use of statistical methods; Ermittlung spezifischer Konzentrationsverlaeufe atmosphaerischer Spurenbestandteile in Niederschlaegen als Methode zur Abschaetzung des flaechenhaften Stoffeintrags in den Boden unter Anwendung statistischer Methoden

    Energy Technology Data Exchange (ETDEWEB)

    Busch, U. [Dortmund Univ. (Germany). Fachbereich Statistik; Vautz, W. [Institut fuer Spektrochemie und Angewandte Spektroskopie (ISAS), Dortmund (Germany); Klockow, D. [Institut fuer Spektrochemie und Angewandte Spektroskopie (ISAS), Dortmund (Germany); Urfer, W. [Dortmund Univ. (Germany). Fachbereich Statistik

    1995-08-01

    Witterungsdaten - und die genauere Abschaetzung der raeumlichen Verteilung von Stoffkonzentrationen in Niederschlaegen. Schliesslich wird ein Interpolationsverfahren fuer Depositionsdaten vorgeschlagen, das die geschaetzten Parameter dieser Modelle und Witterungsdaten als zusaetzliche Information verwendet. Seine Anwendung auf die Daten von 1992 ergibt erste Depositionskarten. Der Bericht schliesst mit einigen Vorschlaegen, wie die Ergebnisse aus diesem Projekt in zukuenftigen Untersuchungen zur trockenen Deposition verwendet werden koennten. (orig.)

  13. Chemistry of the superheavy elements.

    Science.gov (United States)

    Schädel, Matthias

    2015-03-13

    The quest for superheavy elements (SHEs) is driven by the desire to find and explore one of the extreme limits of existence of matter. These elements exist solely due to their nuclear shell stabilization. All 15 presently 'known' SHEs (11 are officially 'discovered' and named) up to element 118 are short-lived and are man-made atom-at-a-time in heavy ion induced nuclear reactions. They are identical to the transactinide elements located in the seventh period of the periodic table beginning with rutherfordium (element 104), dubnium (element 105) and seaborgium (element 106) in groups 4, 5 and 6, respectively. Their chemical properties are often surprising and unexpected from simple extrapolations. After hassium (element 108), chemistry has now reached copernicium (element 112) and flerovium (element 114). For the later ones, the focus is on questions of their metallic or possibly noble gas-like character originating from interplay of most pronounced relativistic effects and electron-shell effects. SHEs provide unique opportunities to get insights into the influence of strong relativistic effects on the atomic electrons and to probe 'relativistically' influenced chemical properties and the architecture of the periodic table at its farthest reach. In addition, they establish a test bench to challenge the validity and predictive power of modern fully relativistic quantum chemical models. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

  14. Experimental Study of Elements Promoting Mixing in Fuel Elements

    International Nuclear Information System (INIS)

    Silin, Nicolas; Juanico, Luis; Delmastro, Dario

    2003-01-01

    In the present work a thermal tracing technique is used to measure the increase of the mixing between subchannels in the presence of different mixing elements.As representative elements a spacer, a spacer with mixing vanes and turbulence promoter buttons were considered.The performance of these elements was evaluated by studying the behavior of a thermal trace in each case.Also the pressure drop for each case is presented.The results present a qualitative and quantitative guide for the application of each one of these appendages in future nuclear elements

  15. Elemental analysis of soil and hair sample by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Chung, Yong Sam; Quraishi, Shamshad Begum; Moon, Jong Hwa; Kim, Sun Ha; Baek, Sung Yeoil; Kang, Sang Hoon; Lim, Jong Myoung; Cho, Hyun Je; Kim, Young Jin

    2004-03-01

    Myanmar soil sample was analyzed by using the instrumental neutron activation analysis. The elemental concentrations in the sample, altogether 34 elements, Al As, Ba, Ce, Co, Cr, Cs, Eu, Fe, Ga, Gd, Hf, Ir, K, La, Lu, Mn, Na, Nd, Rb, Sb, Sc, Se, Sm, Th, Ti, V, Yb, Zn and Zr were determined. The concentration of 17 elements (Al, Au, Br, Ca, Cl, Cr, Cu, Co, Fe, Hg, K, Na, Mn, Mg, Sb, Se, Zn) in human hair samples were determined by INAA For quality control of analytical method, certified reference material was used

  16. Elemental analysis of soil and hair sample by instrumental neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Yong Sam; Quraishi, Shamshad Begum; Moon, Jong Hwa; Kim, Sun Ha; Baek, Sung Yeoil; Kang, Sang Hoon; Lim, Jong Myoung; Cho, Hyun Je; Kim, Young Jin

    2004-03-01

    Myanmar soil sample was analyzed by using the instrumental neutron activation analysis. The elemental concentrations in the sample, altogether 34 elements, Al As, Ba, Ce, Co, Cr, Cs, Eu, Fe, Ga, Gd, Hf, Ir, K, La, Lu, Mn, Na, Nd, Rb, Sb, Sc, Se, Sm, Th, Ti, V, Yb, Zn and Zr were determined. The concentration of 17 elements (Al, Au, Br, Ca, Cl, Cr, Cu, Co, Fe, Hg, K, Na, Mn, Mg, Sb, Se, Zn) in human hair samples were determined by INAA For quality control of analytical method, certified reference material was used.

  17. Effects of Processing Parameters on the Fabrication of in-situ Al/TiC Composites by Thermally Activated Combustion Reaction Process in an Aluminium Melt using Al-TiO_2-C Powder Mixtures

    International Nuclear Information System (INIS)

    Kim, Hwa-Jung; Lee, Jung-Moo; Cho, Young-Hee; Kim, Jong-Jin; Kim, Su-Hyeon; Lee, Jae-Chul

    2012-01-01

    A feasible way to fabricate in-situ Al/TiC composites was investigated. An elemental mixture of Al-TiO_2-C pellet was directly added into an Al melt at 800-920°C to form TiC by self-combustion reaction. The addition of CuO initiates the self-combustion reaction to form TiC in 1-2 um at the melt temperature above 850°C. Besides the CuO addition, a diluent element of excess Al plays a significant role in the TiC formation by forming a precursor phase, Al_3Ti. Processing parameters such as CuO content, the amount of excess Al and the melt temperature, have affected the combustion reaction and formation of TiC, and their influences on the microstructures of in-situ Al/TiC composites are examined.

  18. Large-scale spatial and interspecies differences in trace elements and stable isotopes in marine wild fish from Chinese waters

    International Nuclear Information System (INIS)

    Zhang, Wei; Wang, Wen-Xiong

    2012-01-01

    Highlights: ► A large-scale study on trace element levels in marine wild fish from Chinese waters. ► Spatial variation found for Al, As, Cd, Cr, Fe, Ni, Pb, but not for Ag, Cu, Mo, Se and Zn. ► The Pearl River Estuary contained the highest concentrations of Al, Cr, Ni, and Pb. ► No biomagnification occurred for any of the trace elements studied in marine fish. ► No obvious health risk from the intake of trace elements through fish consumption. - Abstract: We conducted a large scale investigation of twelve trace element levels and stable isotopes (δ 13 C and δ 15 N) in twenty-nine marine wild fish species collected from Chinese coastal waters. Trace element levels varied significantly with species. Clear spatial variations were found for Al, As, Cd, Cr, Fe, Ni, and Pb, whereas Ag, Cu, Mo, Se and Zn did not show much spatial variation. The Pearl River Estuary contained the highest concentrations of Al, Cr, Ni, and Pb, whereas the most southern waters (Haikou) contained the lowest concentrations of Al, Fe, and Pb. There was no correlation between log-transformed trace elements concentrations and δ 15 N values or δ 13 C values, indicating no biomagnification among these trace elements. The calculated hazard quotients (HQ) of 10 elements were less than 1, thus there was no obvious health risk from the intake of trace elements through marine wild fish consumption.

  19. Corrosion and protection of spent Al-clad research reactor fuel during extended wet storage

    International Nuclear Information System (INIS)

    Ramanathan, Lalgudi V.

    2009-01-01

    A variety of spent research reactor fuel elements with different fuel meats, geometries and 235 U enrichments are presently stored under water in basins throughout the world. More than 90% of these fuels are clad in aluminum (Al) or its alloy and are susceptible to corrosion. This paper presents an overview of the influence of Al alloy composition, galvanic effects (Al alloy/stainless steel), crevice effects, water parameters and synergism between these parameters as well as settled solids on the corrosion of typical Al alloys used as fuel element cladding. Pitting is the main form of corrosion and is affected by water conductivity, chloride ion content, formation of galvanic couples with rack supports and settled solid particles. The extent to which these parameters influence Al corrosion varies. This paper also presents potential conversion coatings to protect the spent fuel cladding. (author)

  20. Generalized multiscale finite element methods: Oversampling strategies

    KAUST Repository

    Efendiev, Yalchin R.; Galvis, Juan; Li, Guanglian; Presho, Michael

    2014-01-01

    In this paper, we propose oversampling strategies in the generalized multiscale finite element method (GMsFEM) framework. The GMsFEM, which has been recently introduced in Efendiev et al. (2013b) [Generalized Multiscale Finite Element Methods, J. Comput. Phys., vol. 251, pp. 116-135, 2013], allows solving multiscale parameter-dependent problems at a reduced computational cost by constructing a reduced-order representation of the solution on a coarse grid. The main idea of the method consists of (1) the construction of snapshot space, (2) the construction of the offline space, and (3) construction of the online space (the latter for parameter-dependent problems). In Efendiev et al. (2013b) [Generalized Multiscale Finite Element Methods, J. Comput. Phys., vol. 251, pp. 116-135, 2013], it was shown that the GMsFEM provides a flexible tool to solve multiscale problems with a complex input space by generating appropriate snapshot, offline, and online spaces. In this paper, we develop oversampling techniques to be used in this context (see Hou and Wu (1997) where oversampling is introduced for multiscale finite element methods). It is known (see Hou and Wu (1997)) that the oversampling can improve the accuracy of multiscale methods. In particular, the oversampling technique uses larger regions (larger than the target coarse block) in constructing local basis functions. Our motivation stems from the analysis presented in this paper, which shows that when using oversampling techniques in the construction of the snapshot space and offline space, GMsFEM will converge independent of small scales and high contrast under certain assumptions. We consider the use of a multiple eigenvalue problems to improve the convergence and discuss their relation to single spectral problems that use oversampled regions. The oversampling procedures proposed in this paper differ from those in Hou and Wu (1997). In particular, the oversampling domains are partially used in constructing local