WorldWideScience

Sample records for element synthesis 208pb64ni

  1. Study of the nuclear reactions 208Pb + 58Ni and 208Pb + 64Ni with a focusing time-of-flight spectrometer

    International Nuclear Information System (INIS)

    Sapotta, K.

    1983-01-01

    In the first part of this thesis the construction of a time-of-flight spectrometer for heavy ions with magnetic focusing is described. Then ion trajectories are calculated, and the effective spatial angle and the angular resolution are determined. In the second part the study of quasielastic transfer and deep inelastic reactions of 58 Ni and 64 Ni with 208 Pb at E=265 MeV respectively 260 MeV by means of this spectrometer is described. (HSI) [de

  2. Development of odd-Z-projectile reactions for transactinide element synthesis

    International Nuclear Information System (INIS)

    Folden III, Charles Marvin

    2004-01-01

    The development of new odd-Z-projectile reactions leading to the production of transactinide elements is described. The cross section of the even-Z-projectile 208Pb(64Ni, n)271Ds reaction was measured at two new energies using the Berkeley Gas-filled Separator at the Lawrence Berkeley National Laboratory 88-Inch Cyclotron. In total, seven decay chains attributable to 271Ds were observed. These data, combined with previous results, establish an excitation function for the production of 271Ds. The maximum cross section was 20 +15 -11 pb at a center-of-target energy of 311.5 MeV in the laboratory frame.The data from the 271Ds experiments were used to estimate the optimum beam energy for the new odd-Z-projectile 208Pb(65Cu, n)272-111 reaction using the Fusion by Diffusion theory proposed by Swiatecki, Siwek-Wilczynska, and Wilczynski. A cross section for this reaction was measured for the first time, at a center-of-target energy of 321.1 MeV in the laboratory frame. The excitation energy f or compound nuclei formed at the target center was 13.2 MeV. One decay chain was observed, resulting in a measured cross section of 1.7 +3.9 -1.4 pb. This decay chain is in good agreement with previously published data on the decay of 272-111.The new odd-Z-projectile 208Pb(55Mn, n)262Bh reaction was studied at three different projectile energies, and 33 decay chains of 262Bh were observed. The existence of a previously reported alpha-decaying isomeric state in this nuclide was confirmed. Production of the ground state was preferred at all three beam energies. The maximum cross section was 540 +180 -150 pb at a projectile center-of-target energy of 264.0 MeV. This cross section is much larger than that previously reported for the even-Z-projectile 209Bi(54Cr, n)262Bh reaction, which may be because the 54Cr projectile energies in the latter reaction were too high for optimum production of the 1n product. At the highest projectile energy of 268.0 MeV in the target center, two decay

  3. Conceptual problems with remote element synthesis

    Indian Academy of Sciences (India)

    The notion of remote element synthesis has recently been modified to explain the presence of nucleogenetic isotopic anomalies and decay products of short-lived nuclides by injection of a small amount of exotic nucleogenetic material. Even with this modification, remote element synthesis seems inconsistent with the ...

  4. Tests on the synthesis of superheavy elements

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The article briefly summarizes the study of superheavy elements, starting with speculations on the existence of relatively long-living nuclei via theoretical works to nuclear properties and chemical properties, search for the longest-living nuclei of the calculated stability island in nature, up to the attempts to produce such superheavy elements in large heavy ion accelerators (Berkely, Dubna, Darmstadt, Orsay). Principle and problems of the two methods to achieve a synthesis of such heavy nuclei, i. e. fusion reactions and transfer reactions, are briefly discussed. (RB) [de

  5. Synthesis and properties of superheavy elements

    CERN Document Server

    Hofmann, S

    2003-01-01

    The nuclear shell model predicts that the next doubly magic shell-closure beyond sup 2 sup 0 sup 8 Pb is at a proton number Z = 114, 120, or 126 and at a neutron number N = 172 or 184. The outstanding of experimental investigations is the exploration of this region of spherical 'SuperHeavy Elements' (SHEs). Experimental methods are described which allowed for the identification of elements 107 to 112 in studies of cold fusion reactions based on lead and bismuth targets. Also presented are data which were obtained on the synthesis of elements 112, 114, and 116 in investigation of hot fusion reactions using actinide targets. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission, not fission. Decay properties as well as reaction cross- sections are compared with the results of theoretical studies. Finally, plans are presented for the further development of the experimental set-up and the application of new techniques. At a higher sensitivity, the exploration of the regio...

  6. Superheavy Element Synthesis and Nuclear Structure

    International Nuclear Information System (INIS)

    Ackermann, D.

    2009-01-01

    The search for the next closed proton and neutron shells beyond 2 08P b has yielded a number of exciting results in terms of the synthesis of new elements [1,2,3]. The superheavy elements (SHE), however, are a nuclear structure phenomenon. They owe their existence to the quantum mechanical origin of shell correction energies without which they would not be bound. In recent years the development of efficient experimental set-ups including separators and advanced particle and photon detection arrangements allowed for more and more detailed nuclear structure studies for nuclei at and beyond Z=100. A review of those recent achievements is given in ref. [4]. Among the most interesting features is the observation of K-isomeric states. Experimentally about 14 cases have been identified in the region of Z>96 as shown in Fig. 1. K-isomers or indications of their existence have been found for almost all even-Z elements in the region Z=100 to 110. We could recently establish and/or confirm such states in the even-even isotopes 2 52,254N o [5]. The heaviest nucleus where such a state was found is 2 70D s with Z=110 as we reported in 2001 [6]. Those nuclear structure studies lay out the grounds for a detailed understanding of these heavy and high-Z nuclear systems, and contribute at the same time valuable information to preparation of strategies to successfully continue the hunt for the localisation of the next spherical proton and neutron shells after 2 08P b. The recent activities for both SHE synthesis and nuclear structure investigations at GSI will be reported.(author)

  7. On the synthesis of new elements

    International Nuclear Information System (INIS)

    Hofmann, S.

    2003-01-01

    The nuclear shell model predicts that the next doubly magic shell-closure beyond 208 Pb is at a proton number between Z=114 and 126 and at a neutron number N=172 or 184. The outstanding aim of experimental investigations is the exploration of this region of spherical 'Superheavy Elements'. This article describes the experiments that were performed recently at the GSI SHIP. They resulted in an unambiguous identification of elements 110 to 112. They were negative so far in searching for elements 113, 116, and 118. The measured decay data are compared with theoretical predictions. Some aspects concerning the reaction mechanism are also presented. (orig.)

  8. Synthesis of superheavy elements by cold fusion

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, S [Gesellschaft fuer Schwerionenforschung (GSI), Helmholtzzentrum fuer Schwerionenforschung Gmbh (Germany)

    2009-12-31

    The nuclear shell model predicts that the next doubly magic shell-closure beyond {sup 208}Pb is at the proton number Z=114, 120, or 126 and at the neutron number N=172 or 184. The outstanding aim of experimental investigations is the exploration of this region of spherical 'Super Heavy Elements' (SHEs). Using cold fusion reactions which are based on lead and bismuth targets, the new elements from 107 to 112 were synthesized at GSI in Darmstadt, Germany. Some of these results were confirmed at RIKEN in Wako, Japan, where also a relatively neutron-deficient isotope of element 113 was synthesized. In hot fusion reactions of {sup 48}Ca projectiles with actinide targets, a more neutron-rich isotope of element 112 and the new elements from 113 to 116 and even 118 were produced at FLNR in Dubna, Russia. Recently, part of these hot fusion data, which represent the first identification of nuclei located on the predicted island of SHEs, were confirmed in two independent experiments. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission rather than fission. The decay properties as well as reaction cross-sections are compared with results of theoretical studies.

  9. Finite element design for the HPHT synthesis of diamond

    Science.gov (United States)

    Li, Rui; Ding, Mingming; Shi, Tongfei

    2018-06-01

    The finite element method is used to simulate the steady-state temperature field in diamond synthesis cell. The 2D and 3D models of the China-type cubic press with large deformation of the synthesis cell was established successfully, which has been verified by situ measurements of synthesis cell. The assembly design, component design and process design for the HPHT synthesis of diamond based on the finite element simulation were presented one by one. The temperature field in a high-pressure synthetic cavity for diamond production is optimized by adjusting the cavity assembly. A series of analysis about the influence of the pressure media parameters on the temperature field are examined through adjusting the model parameters. Furthermore, the formation mechanism of wasteland was studied in detail. It indicates that the wasteland is inevitably exists in the synthesis sample, the distribution of growth region of the diamond with hex-octahedral is move to the center of the synthesis sample from near the heater as the power increasing, and the growth conditions of high quality diamond is locating at the center of the synthesis sample. These works can offer suggestion and advice to the development and optimization of a diamond production process.

  10. The synthesis of ammonia from its elements

    Indian Academy of Sciences (India)

    The discovery of the process for economically viable manufacture of ... present century that the production of ammonia from the elements has been discovered, ... with the advent of the industrial age, the products of the soil are carried off from ..... also discovered an improvement in the design of the oven which overcame the ...

  11. Superheavy Element Synthesis And Nuclear Structure

    International Nuclear Information System (INIS)

    Ackermann, D.; Block, M.; Burkhard, H.-G.; Heinz, S.; Hessberger, F. P.; Khuyagbaatar, J.; Kojouharov, I.; Mann, R.; Maurer, J.; Antalic, S.; Saro, S.; Venhart, M.; Hofmann, S.; Leino, M.; Uusitalo, J.; Nishio, K.; Popeko, A. G.; Yeremin, A. V.

    2009-01-01

    After the successful progress in experiments to synthesize superheavy elements (SHE) throughout the last decades, advanced nuclear structure studies in that region have become feasible in recent years thanks to improved accelerator, separation and detection technology. The means are evaporation residue(ER)-α-α and ER-α-γ coincidence techniques complemented by conversion electron (CE) studies, applied after a separator. Recent examples of interesting physics to be discovered in this region of the chart of nuclides are the studies of K-isomers observed in 252,254 No and in 270 Ds.

  12. A probability of synthesis of the superheavy element Z = 124

    Energy Technology Data Exchange (ETDEWEB)

    Manjunatha, H.C. [Government College for Women, Department of Physics, Kolar, Karnataka (India); Sridhar, K.N. [Government First Grade College, Department of Physics, Kolar, Karnataka (India)

    2017-10-15

    We have studied the fusion cross section, evaporation residue cross section, compound nucleus formation probability (P{sub CN}) and survival probability (P{sub sur}) of different projectile target combinations to synthesize the superheavy element Z=124. Hence, we have identified the most probable projectile-target combination to synthesize the superheavy element Z = 124. To synthesize the superheavy element Z=124, the most probable projectile target combinations are Kr+Ra, Ni+Cm, Se+Th, Ge+U and Zn+Pu. We hope that our predictions may be a guide for the future experiments in the synthesis of superheavy nuclei Z = 124. (orig.)

  13. Synthesis of selective extractor for minor actinide elements

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Seung [Konyang University, Nonsan (Korea); Cho, Moon Hwan [Kangwon National University, Chunchon (Korea)

    1998-04-01

    To selectively co-separate the lanthanide and actinide elements (MA) such as Am or Cm ion from radioactive waste, synthesis of diamide derivatives has been accomplished. In addition, picoline amide derivatives were also synthesized for selectively separate the minor actinide elements from lanthanide elements. The content of research has don are as follows: (1) synthesis of diamide as co-extractant (2) introduction of n-tetradecyl to increase the lipophilicity (3) Picolyl chloride, intermediate of the final product, was synthesized by improved method rather than reported method. (4) The length of alkyl side chain was adjusted to increase the lipophilicity of free ligand and its derivatives able to selectively separate the actinide metal from lanthanide metal ions was successfully synthesized and determined their purity by analytical instruments. (author). 12 refs., 28 figs.

  14. The synthesis of the deformed superheavy elements 107 to 111

    International Nuclear Information System (INIS)

    Armbuster, P.

    1995-01-01

    By inflight separation, implantation into Si-detector arrays, and correlation analysis of subsequent α-decay chains many isotopes were discovered at GSI since 1980, among others the elements Nielsbohriurn, Hassium and Meitnerium. The sensitivity of the method allows to identify an element by one decay chain, as we demonstrated for the case of 266 Mt. After a break of our work during the time when the new accelerator system SIS-FRS-ESR was installed (1989-1993) at GSI, and many improvements of our system EZR-UNILAC-SHIP accomplished, we restarted element synthesis in 1994. The synthesis of the isotopes 269 110, 271 110, and 272 111 of the new elements Z--110 and Z=l11 was a first success at the end of 1994. This discovery is in the center of this presentation. The reaction mechanism, a one-step, cold and compact rearrangement process at a level of some 10 -36 cm 2 is discussed. Cross sections and excitation functions systematically studied allow to extrapolate to the next element Z=112, which seems not to be out of reach

  15. The synthesis and decay properties of the heaviest elements

    International Nuclear Information System (INIS)

    Oganesyan, Yu.Ts.

    2000-01-01

    The synthesis and the study of radioactive properties of new elements is considered with respect to the existence of the 'islands of stability' of hypothetical superheavy elements predicted by the theory more than 35 years ago. Experimental data demonstrating an enhanced stability of nuclei in the vicinity of deformed shells with Z=108 and N=162 is discussed from the point of view of advent into more heavy and much more stable nuclides near the predicted spherical shells Z=114-122 and N=184 following after the doubly magic nucleus 208 Pb. The author presents the results of experiments on the synthesis of isotopes of elements 114 and 116 in the fusion reactions with 48 Ca. In these reactions the decay chains of heavy atoms consisting of sequential α-decays interrupted by spontaneous fission have been observed. The decay energies and probabilities are compared with predictions of different theoretical models describing the structure of heavy nuclei. The obtained results are considered as the first experimental evidence of the existence of domains of stability of superheavy nuclei which substantially extends the boundaries of existence of chemical elements

  16. Synthesis and chemistry of elemental 2D materials

    Energy Technology Data Exchange (ETDEWEB)

    Mannix, Andrew J.; Kiraly, Brian; Hersam, Mark C.; Guisinger, Nathan P.

    2017-01-25

    2D materials have attracted considerable attention in the past decade for their superlative physical properties. These materials consist of atomically thin sheets exhibiting covalent in-plane bonding and weak interlayer and layer-substrate bonding. Following the example of graphene, most emerging 2D materials are derived from structures that can be isolated from bulk phases of layered materials, which form a limited library for new materials discovery. Entirely synthetic 2D materials provide access to a greater range of properties through the choice of constituent elements and substrates. Of particular interest are elemental 2D materials, because they provide the most chemically tractable case for synthetic exploration. In this Review, we explore the progress made in the synthesis and chemistry of synthetic elemental 2D materials, and offer perspectives and challenges for the future of this emerging field.

  17. The Synthesis and Decay Properties of the Heaviest Elements

    CERN Document Server

    Oganessian, Yu T

    2000-01-01

    The synthesis and the study of radioactive properties of new elements is considered with respect to the existence of the "islands of stability" of hypothetical superheavy elements predicted by the theory more than 35 years ago. Experimental data demonstrating an enhanced stability of nuclei in the vicinity of deformed shells with Z=108 and N=162 is discussed from the point of view of advent into more heavy and much more stable nuclides near the predicted spherical shells Z=114-122 and N=184 following after the doubly magic nucleus ^{208}Pb. The author presents the results of experiments on the synthesis of isotopes of elements 114 and 116 in the fusion reactions with ^{48}Ca. In these reactions the decay chains of heavy atoms consisting of sequential alpha-decays interrupted by spontaneous fission have been observed. The decay energies and probabilities are compared with predictions of different theoretical models describing the structure of heavy nuclei. The obtained results are considered as the first exper...

  18. Synthesis of the New Element with Z=117

    International Nuclear Information System (INIS)

    Hamilton, J H; Ramayya, A V; Oganessian, Yu Ts; Abdullin, F Sh; Dmitriev, S N; Itkis, M G; Lobanov, Yu V; Mezentsev, A N; Polyakov, A N; Bailey, P D; Benker, D; Ezold, J; Porter, C E; Riley, F; Roberto, J B; Bennett, M E; Henderson, R A; Moody, K J; Nelson, S L; Ryabinin, M A

    2011-01-01

    The synthesis of the new chemical element with atomic number Z=117 is presented. The isotopes 293 117 and 294 117were produced in fusion reactions between 48 Ca and 249 Bk. The 249 Bk was produced in the High Flux Isotope Reactor and chemically separated at Oak Ridge. Decay chains involving eleven new nuclei were identified by means of the Dubna Gas Filled Recoil Separator. The measured decay properties show a strong rise of stability for super-heavy nuclei toward N=184.

  19. The Effect of Neutrino Oscillations on Supernova Light Element Synthesis

    International Nuclear Information System (INIS)

    Yoshida, Takashi; Kajino, Toshitaka; Yokomakura, Hidekazu; Kimura, Keiichi; Takamura, Akira; Hartmann, Dieter H.

    2006-01-01

    We investigate light element synthesis through the ν-process during supernova explosions considering neutrino oscillations and investigate the dependence of 7Li and 11B yields on neutrino oscillation parameters mass hierarchy and θ13. The adopted supernova explosion model for explosive nucleosynthesis corresponds to SN 1987A. The 7Li and 11B yields increase by about factors of 1.9 and 1.3 in the case of normal mass hierarchy and adiabatic 13-mixing resonance compared with the case without neutrino oscillations. In the case of inverted mass hierarchy or nonadiabatic 13-mixing resonance, the increase in 7Li and 11B yields is much smaller. Astronomical observations of 7Li/11B ratio in stars formed in regions strongly affected by prior generations of supernovae would constrain mass hierarchy and the range of θ13

  20. Introduction to basic concepts and elements in process synthesis and process intensification

    DEFF Research Database (Denmark)

    Rong, Ben-Guang

    2017-01-01

    In this chapter, we introduce some basic concepts and elements for process synthesis (PS) and process intensification (PI). These basic concepts and elements are taken partially from distillation systems synthesis and intensification, as described in Chapter 2. In Chapter 2,we present six distill...... these common concepts and elements in the context of general PS and PI works. We hope that at least some of the concepts and elements can be examined and addressed in the methodological approaches for PS and PI....

  1. Distributional Fate of Elements during the Synthesis of Zeolites from South African Coal Fly Ash

    Directory of Open Access Journals (Sweden)

    Pieter W. Du Plessis

    2014-04-01

    Full Text Available The synthesis of zeolites from South African coal fly ash has been deemed a viable solution to the growing economical strain caused by the disposal of ash in the country. Two synthesis routes have been studied thus far namely the 2-step method and the fusion assisted process. Fly ash contains several elements originating from coal which is incorporated in the ash during combustion. It is vital to determine the final destination of these elements in order to unveil optimization opportunities for scale-up purposes. The aim of this study was to perform a material balance study on both synthesis routes to determine the distributional fate of these elements during the synthesis of zeolites. Zeolites were first synthesized by means of the two synthesis routes. The composition of all raw materials and products were determined after which an overall and elemental balance were performed. Results indicated that in the 2-step method almost all elements were concentrated in the solid zeolite product while during the fusion assisted route the elements mostly report to the solid waste. Toxic elements such as Pb, Hg, Al, As and Nb were found in both the supernatant waste and washing water resulting from each synthesis route. It has also been seen that large quantities of Si and Al are wasted in the supernatant waste. It is highly recommended that the opportunity to recycle this liquid waste be investigated for scale-up purposes. Results also indicate that efficiency whereby Si and Al are extracted from fused ash is exceptionally poor and should be optimized.

  2. Electrochemical synthesis of transition element complexes with carboxyl- and carbonyl-containing ligands

    International Nuclear Information System (INIS)

    Frolov, V.Yu.; Bolotin, S.N.; Panyushkin, V.T.

    2005-01-01

    Complexes of d- and f-elements (E = Cu, Ni, Zn, Nd, Tb, Pr, Gd, Er) with carboxyl- and carbonyl-containing ligands were synthesized by the electrochemical method. The products were characterized by elemental analysis, thermal gravimetric analysis and IR spectra. The influence exerted by a number of factors on the process course was studied. The dependence of the electro synthesis parameters on the composition of the forming compounds was established. A new method for anodic synthesis of these compounds was developed [ru

  3. Actinide targets for the synthesis of super-heavy elements

    International Nuclear Information System (INIS)

    Roberto, J.B.; Alexander, C.W.; Boll, R.A.; Burns, J.D.; Ezold, J.G.; Felker, L.K.; Hogle, S.L.; Rykaczewski, K.P.

    2015-01-01

    Since 2000, six new super-heavy elements with atomic numbers 113 through 118 have been synthesized in hot fusion reactions of "4"8Ca beams on actinide targets. These target materials, including "2"4"2Pu, "2"4"4Pu, "2"4"3Am, "2"4"5Cm, "2"4"8Cm, "2"4"9Cf, and "2"4"9Bk, are available in very limited quantities and require specialized production and processing facilities resident in only a few research centers worldwide. This report describes the production and chemical processing of heavy actinide materials for super-heavy element research, current availabilities of these materials, and related target fabrication techniques. The impact of actinide materials in super-heavy element discovery is reviewed, and strategies for enhancing the production of rare actinides including "2"4"9Bk, "2"5"1Cf, and "2"5"4Es are described.

  4. Kodai School on ‘Synthesis of Elements in Stars’

    CERN Document Server

    Goswami, Aruna; Principles and Perspectives in Cosmochemistry

    2010-01-01

    A fundamental question in contemporary astrophysics is the origin of the elements. Cosmochemistry seeks to answer when, how and where the chemical elements arose. Quantitative answers to these fundamental questions require a multi-disciplinary approach involving stellar evolution, explosive nucleosynthesis and nuclear reactions in different astrophysical environments. There remain, however, many outstanding problems and cosmochemistry remains a fertile area of research. This book is among the first in recent times to put together the essentials of cosmochemistry, combining contributions from leading astrophysicists in the field. The chapters have been organized to provide a clear description of the fundamentals, an introduction to modern techniques such as computational modelling, and glimpses of outstanding issues.

  5. Synthesis of new thermoelectrics using modulated elemental reactants

    Energy Technology Data Exchange (ETDEWEB)

    Hornbostel, M D; Sellinschegg, H; Johnson, D C

    1997-07-01

    A series of new, metastable ternary crystalline compounds with the skutterudite crystal structure have been synthesized using modulated elemental reactants. The initial reactants are made up of multiple repeats of a {approximately}25 {angstrom} thick unit containing elemental layers of the desired ternary metal, iron and antimony. Low temperature annealing (150 C) results in interdiffusion of the elemental layers to form amorphous reaction intermediates. Annealing these intermediates at temperatures between 200 C and 250 C results in exothermic crystallization of the desired skutterudite crystal structure. Most of the new compounds prepared are only kinetically stable, decomposing exothermically to form thermodynamically more stable mixtures of binary compounds and elements. Low angle x-ray diffraction studies show that the resulting films are exceedingly smooth. These films have an ideal geometry for measuring properties of importance for thermoelectric devices--the Seebeck coefficient and the electrical conductivity. Thermal conductivity can be measured using a modification of the 3{omega} technique of Cahill. Samples can be produced rapidly, allowing for systematic screening and subsequent optimization as a function of composition and doping levels.

  6. Poliovirus RNA synthesis in vitro: structural elements and antibody inhibition

    International Nuclear Information System (INIS)

    Semler, B.L.; Hanecak, R.; Dorner, L.F.; Anderson, C.W.; Wimmer, E.

    1983-01-01

    The poliovirus RNA polymerase complex has been analyzed by immunoautoradiography using antibody probes derived from purified replicase (P3) region viral polypeptides. Antibody preparations made against the polio RNA polymerase, P3-4b, detected a previously unreported cellular protein that copurifies with the RNA polymerase. An IgG fraction purified from rabbit antiserum to polypeptide P3-2, a precursor fo the RNA polymerase, specifically inhibits poliovirus RNA synthesis in vitro. The authors have also immunoprecipitated a 60,000-dalton protein (P3-4a) with antiserum to protein P3-4b and have determined the precise genomic map position of this protein by automated Edman degradation. Protein P3-4a originates by cleavage of the RNA polymerase precursor at a glutamine-glucine amino acid pair not previously reported to be a viral cleavage site

  7. Synthesis and investigation of superheavy elements - perspectives with radioactive beams

    International Nuclear Information System (INIS)

    Muenzenberg, G.

    1997-09-01

    The perspectives for the investigation of heavy and superheavy elements with intense beams of radioactive nuclei available from the new generation of secondary beam facilities in combination with modern experimental developments are the subject of this paper. The nuclear properties of the recently discovered shell nuclei centered at Z=108 and N=164 and predictions on the location of the superheavy region with improved theoretical models will be discussed. (orig.)

  8. Synthesis of a New Element with Atomic Number Z=117

    International Nuclear Information System (INIS)

    Oganessian, Yu. Ts.; Abdullin, F. Sh.; Dmitriev, S. N.; Itkis, M. G.; Lobanov, Yu. V.; Mezentsev, A. N.; Polyakov, A. N.; Sagaidak, R. N.; Shirokovsky, I. V.; Subbotin, V. G.; Sukhov, A. M.; Tsyganov, Yu. S.; Utyonkov, V. K.; Voinov, A. A.; Vostokin, G. K.; Bailey, P. D.; Benker, D. E.; Ezold, J. G.; Porter, C. E.; Riley, F. D.

    2010-01-01

    The discovery of a new chemical element with atomic number Z=117 is reported. The isotopes 293 117 and 294 117 were produced in fusion reactions between 48 Ca and 249 Bk. Decay chains involving 11 new nuclei were identified by means of the Dubna gas-filled recoil separator. The measured decay properties show a strong rise of stability for heavier isotopes with Z≥111, validating the concept of the long sought island of enhanced stability for superheavy nuclei.

  9. Recent developments in the synthesis of super heavy elements

    International Nuclear Information System (INIS)

    Ackermann, D.

    2001-01-01

    Throughout the passed two decades isotopes of the elements with atomic numbers 107-112 have been synthesized and unambiguously identified at the velocity filter SHIP at GSI. In a recent experiment at SHIP the results for element 112 have been confirmed and a third decay chain of the isotope 277 112 has been observed. Cold fusion reactions using Pb- and Bi- targets and evaporation residue(ER)-α-α correlations together with an efficient separation and detection system are the major ingredients for the success of these experiments. The sensitivity limit of the set-up at GSI has reached the 1pb level. For a systematic investigation in this region of the chart of nuclei and to synthesize heavier nuclei this limit has to be pushed to even lower values. An extensive development program is pursued at SHIP in order to reach at least an order of magnitude lower cross sections. Systematic investigations, the construction of decay chain networks and mass measurements are some of the possible approaches to study the decay chains attributed to isotopes of the elements 114, 116 and 118 at Dubna and Berkeley, which are, in contrast to those observed at GSI, not connected to decays of known isotopes. For the Berkeley results, in particular, several trials of confirmation have been undertaken at various laboratories including GSI

  10. gon eptu l pro lems with remote element synthesis

    Indian Academy of Sciences (India)

    o w xD q rrison h rD fog rd h hD f dhw r q nd wur li e IWWI gomposition of sol r fl re no le g ses preserved in meteorite p rent ody regolithY tF qeophysF esF WT. IWQPIEEIWQQH eynolds t r IWTH hetermin tion of the ge of the elementsY. hysF evF vettF R VEEIH eynolds t r IWTH ssotopi omposition of primordi l xenonY.

  11. Dissipative dynamics of the synthesis of superheavy elements

    Energy Technology Data Exchange (ETDEWEB)

    Wada, Takahiro; Aritomo, Y.; Tokuda, T.; Okazaki, K.; Ohta, M. [Konan Univ., Kobe (Japan). Dept. of Physics; Abe, Y.

    1997-07-01

    Fusion-fission process in heavy systems are analyzed by Smoluchowski equation taking into account the temperature dependent shell correction energy. The evaporation residue cross sections of superheavy elements have been shown to have an optimum value at a certain temperature, due to the balance between the diffusibility for fusion at high temperature and the restoration of the shell correction energy against fission at low temperature. The isotope dependence of the evaporation residue cross section is found to be very strong. Neutron rich compound system with small neutron separation energy is favorable for larger cross section because of the quick restoration of the shell correction energy. The Z-dependence is discussed for the formation of the compound nuclei with Z=102 to Z=114. (author)

  12. Synthesis Study of a 6-Element Non-Uniform Array with Tilted Elements for CLARREO Project

    Science.gov (United States)

    Jamnejad, Vahraz; Hoorfar, Ahmad

    2012-01-01

    This paper presents the results of a preliminary study of the gain/pattern properties of a 6-element Radio Occultation (RO) array for the proposed CLARREO (Climate Absolute Radiance and Refractivity Observatory (CLARREO) Project. CLARREO is one of the 4 highest priority missions recommended in the National Research Council Earth Science Decadal Survey.

  13. Reliability enhancement of portal frame structure by finite element synthesis

    International Nuclear Information System (INIS)

    Nakagiri, S.

    1989-01-01

    The stochastic finite element methods have been applied to the evaluation of structural response and reliability of uncertain structural systems. The structural reliability index of the advanced first-order second moment (AFOSM) method is a candidate of the measure of assessing structural safety and reliability. The reliability index can be evaluated when a baseline design of structures under interest is proposed and the covariance matrix of the probabilistic variables is acquired to represent uncertainties involved in the structure systems. The reliability index thus evaluated is not assured the largest one for the structure. There is left a possibility to enhance the structural reliability for the given covariance matrix by changing the baseline design. From such a viewpoint of structural optimization, some ideas have been proposed to maximize the reliability or to minimize the failure probability of uncertain structural systems. A method of changing the design is proposed to increase the reliability index from its baseline value to another desired value. The reliability index in this paper is calculated mainly by the method of Lagrange multiplier

  14. Fusion-fission dynamics and synthesis of the superheavy elements

    International Nuclear Information System (INIS)

    Abe, Yasuhisa

    2003-01-01

    given by a product of the sticking and the formation probabilities. The former is that for the system to overcome the Coulomb barrier to stick each other, while the latter that for the system to overcome the conditional saddle to form the spherical shape. Residue cross sections for the superheavy elements are predicted by combining the survival probability which is calculated with the statistical theory of decay. Some examples will be presented on Z=110, 111, 112 and 113. (author)

  15. Q-value effects in the synthesis of superheavy elements

    International Nuclear Information System (INIS)

    Graeger, Reimar

    2010-01-01

    Superheavy elements (Z>or similar 104) only exist due to nuclear shell effects, which stabilize them against spontaneous fission (SF). Theoretical calculations predict these shell stabilization effects to reach a maximum at the closures of the next spherical proton and neutron shells, which are anticipated in the region between Z=114 and Z=126 and at N=184. More recent calculations, that also consider deformed nuclear shapes extended this picture and predicted deformed shell closures at Z=108 and at N=162, creating a region of enhanced stability around 270 Hs, confirmed in recent Hs chemistry experiments by measuring the decay of 270 Hs for the first time. Recently, the formation of deformed doubly-magic 270 Hs in the 4n evaporation channel in the fusion reactions 248 Cm( 26 Mg,4n), 244 Pu( 30 Si,4n), 238 U( 36 S,4n), and 226 Ra( 48 Ca,4n) was studied theoretically using a two-parameter Smoluchowski equation. Simple entrance channel arguments make compound nucleus (CN) formation appear favorable for systems with larger mass asymmetry. However, due to a lower reaction Q value, the reactions 238 U( 36 S,4n) 270 Hs and 226 Ra( 48 Ca,4n) 270 Hs are predicted to have higher cross sections compared to the reactions 248 Cm( 26 Mg,4n) 270 Hs and 244 Pu( 30 Si,4n) 270 Hs. The aim of the research done in the framework of this thesis was to study the influence of the reaction (B-Q)-value on the yield of SHE produced in nuclear fusion reactions. Therefore the most promising reactions 36 S+ 238 U and 48 Ca+ 226 Ra have been investigated and compared with the already measured reaction 26 Mg+ 248 Cm. The reaction 36 S+ 238 U was investigated at two beam energies. One correlated decay chain attributed to 270 Hs was found at E * =51 MeV resulting in a cross section of 0.8 -0.7 +2.6 pb. The reaction 48 Ca+ 226 Ra was investigated at three beam energies. Six correlated decay chains attributed to 270 Hs were detected at E * =40 MeV corresponding to a cross section of 8.3 -3.7 +6.7 pb

  16. An assessment of finite element synthesis model using 3D FEM

    International Nuclear Information System (INIS)

    Jagannathan, V.; Rastogi, B.P

    1983-01-01

    For the solution of multigroup diffusion theory equations a code system called FEMSYN has been developed. The code FEMSYN incorporates a finite difference (FD) module, a finite element (FE) module and one module based on single channel flux synthesis (SCFS) method, which uses trial functions generated by either FD or FE method. The 3D problems can be tackled by all the three modules. The 3D FE solutions are cheaper in comparison with fine mesh FD computations and are quite accurate. The accuracy is improved by proper choice of rectangular and triangular right prismatic elements and polynomial order in case of 3D FE analyses. Synthesis method using FE trial functions provides the fastest means of solution for 3D problems. In this paper, the FE synthesis method has been compared with 3D FE technique for the case of IAEA PWR benchmark problem. It is concluded from the above comparison that FE synthesis method can give at negligible computational efforts, accurate eigenvalue estimates and satisfactory prediction of reactor core power profiles

  17. Crystal chemistry, properties and synthesis of microporous silicates containing transition elements

    International Nuclear Information System (INIS)

    Chukanov, Nikita V; Pekov, Igor V; Rastsvetaeva, Ramiza K

    2004-01-01

    The review surveys and generalises recent data on synthesis methods, physicochemical properties and crystal chemistry of silicate microporous materials containing transition elements (amphoterosilicates). The frameworks of these materials, unlike those of usual aluminosilicate zeolites, are built from tetrahedrally coordinated atoms along with atoms of various elements (Ti, Nb, Zr, Ta, Sn, W, Fe, Mn, Zn, etc.) with coordination numbers of 6 or 5. Many amphoterosilicates possess ion-exchange properties and can serve as catalysts for redox reactions, sorbents, etc. The structural diversity of synthetic and natural amphoterosilicates provides the basis for the preparation of microporous materials with different properties.

  18. Synthesis of superheavy elements: Uncertainty analysis to improve the predictive power of reaction models

    OpenAIRE

    Lu , H.; Boilley , D.; Abe , Y.; Shen , C.

    2016-01-01

    13 pages, 13 figures, submitted for publication in PRC; International audience; Background: Synthesis of super-heavy elements is performed by heavy-ion fusion-evaporation reactions. However , fusion is known to be hindered with respect to what can be observed with lighter ions. Thus some delicate ambiguities remain on the fusion mechanism that eventually lead to severe discrepancies in the calculated formation probabilities coming from different fusion models. Purpose: In the present work, we...

  19. Some new approaches to the synthesis of heavy and superheavy elements

    International Nuclear Information System (INIS)

    Flerov, G.N.

    1980-01-01

    The results of work on the synthesis of heavy and superheavy elements are considered. It is shown that the new regularity of the systematics of spontaneous-fission half-lives, established for heavy nuclei at Dubna, has made it possible to extend the region of the nuclei being synthesized. In particular, it becomes possible to produce relatively long-lived heavy isotopes of Z>=107. The results of experiments to study the emission of energetic α-particles in the collision of heavy nuclei are presented. It is noted that such reactions can be used to produce atomic nuclei with low excitation energy and large angular momentum. The possible use of similar reactions in the synthesis of heavy and superheavy elements is discussed. In case the existence of a naturally occurring superheavy element has been established, a possibility will arise to synthesize in nuclear reactions a number of isotopes belonging to the island of stability, and to investigate their properties. The present state of work on the search for superheavy elements in nature is briefly described

  20. Elements for harnessing participatory action research to strengthen health managers' capacity: a critical interpretative synthesis.

    Science.gov (United States)

    Tetui, Moses; Zulu, Joseph Mumba; Hurtig, Anna-Karin; Ekirapa-Kiracho, Elizabeth; Kiwanuka, Suzanne N; Coe, Anna-Britt

    2018-04-19

    Health managers play a key role in ensuring that health services are responsive to the needs of the population. Participatory action research (PAR) is one of the approaches that have been used to strengthen managers' capacity. However, collated knowledge on elements for harnessing PAR to strengthen managers' capacity is missing. This paper bridges this gap by reviewing existing literature on the subject matter. A critical interpretive synthesis method was used to interrogate eight selected articles. These articles reported the use of PAR to strengthen health managers' capacity. The critical interpretive synthesis method's approach to analysis guided the synthesis. Here, the authors interpretively made connections and linkages between different elements identified in the literature. Finally, the Atun et al. (Heal Pol Plann, 25:104-111, 2010) framework on integration was used to model the elements synthesised in the literature into five main domains. Five elements with intricate bi-directional interactions were identified in the literature reviewed. These included a shared purpose, skilled facilitation and psychological safety, activity integration into organisational procedures, organisational support, and external supportive monitoring. A shared purpose of the managers' capacity strengthening initiative created commitment and motivation to learn. This purpose was built upon a set of facilitation skills that included promoting participation, self-efficacy and reflection, thereby creating a safe psychological space within which the managers interacted and learnt from each other and their actions. Additionally, an integrated intervention strengthened local capacity and harnessed organisational support for learning. Finally, supportive monitoring from external partners, such as researchers, ensured quality, building of local capacity and professional safety networks essential for continued learning. The five elements identified in this synthesis provide a basis upon

  1. Synthesis of hydrocode and finite element technology for large deformation Lagrangian computation

    International Nuclear Information System (INIS)

    Goudreau, G.L.; Hallquist, J.O.

    1979-08-01

    Large deformation engineering analysis at Lawrence Livermore Laboratory has benefited from a synthesis of computational technology from the finite difference hydrocodes of the scientific weapons community and the structural finite element methodology of engineering. Two- and three-dimensional explicit and implicit Lagrangian continuum codes have been developed exploiting the strengths of each. The explicit methodology primarily exploits the primitive constant stress (or one point integration) brick element. Similarity and differences with the integral finite difference method are discussed. Choice of stress and finite strain measures, and selection of hour glass viscosity are also considered. The implicit codes also employ a Cauchy formulation, with Newton iteration and a symmetric tangent matrix. A library of finite strain material routines includes hypoelastic/plastic, hyperelastic, viscoelastic, as well as hydrodynamic behavior. Arbitrary finite element topology and a general slide-line treatment significantly extends Lagrangian hydrocode application. Computational experience spans weapons and non-weapons applications

  2. Homoserine Lactone as a Structural Key Element for the Synthesis of Multifunctional Polymers

    Directory of Open Access Journals (Sweden)

    Fabian Marquardt

    2017-04-01

    Full Text Available The use of bio-based building blocks for polymer synthesis represents a milestone on the way to “green” materials. In this work, two synthetic strategies for the preparation of multifunctional polymers are presented in which the key element is the functionality of homoserine lactone. First, the synthesis of a bis cyclic coupler based on a thiolactone and homoserine lactone is displayed. This coupler was evaluated regarding its regioselectivity upon reaction with amines and used in the preparation of multifunctional polymeric building blocks by reaction with diamines. Furthermore, a linear polyglycidol was functionalized with homoserine lactone. The resulting polyethers with lactone groups in the side chain were converted to cationic polymers by reaction with 3-(dimethylamino-1-propylamine followed by quaternization with methyl iodide.

  3. Synthesis of superheavy elements and dinuclear-system concept of compound-nucleus formation

    Energy Technology Data Exchange (ETDEWEB)

    Antonenko, N.V.; Adamian, G.G.; Cherepanov, E.A. [Joint Institute for Nuclear Research, Dubna (Russian Federation)] [and others

    1996-12-31

    Dinuclear system concept is applied to the analysis of reactions used for the synthesis of elements with Z = 110, 112, 114, and 116. The inner fusion barriers obtained for these reactions are in good agreement with the experimental estimations resulted from the excitation energies of compound nuclei. A model is suggested for the calculation of the competition between complete fusion and quasifission in reactions with heavy nuclei. The fusion rate through the inner fusion barrier in mass asymmetry is found by using the multidimensional Kramers-type stationary solution of the Fokker-Planck equation. The influence of dissipative effects on the dynamics of nuclear fusion is considered.

  4. Sir Fred Hoyle and the theory of the synthesis of the elements

    Science.gov (United States)

    Arnett, David

    Some of Fred Hoyle's pioneering ideas about the site and the nature of the synthesis of the elements are examined in a modern context of theory, experiment and observations. Hoyle's ideas concerning the nucleosynthesis cycle of stellar birth and death, rotational instability of supernovae, the onion-skin model of presupernovae, neutronization, nuclear statistical equilibrium and core collapse, thermonuclear supernovae, nucleosynthesis processes and freeze-out are discussed. The history of the clash of theory and experiment on the second excited state of 8Be and helium ignition in red giants is reviewed.

  5. High-performance quantum-dot solids via elemental sulfur synthesis

    KAUST Repository

    Yuan, Mingjian

    2014-03-21

    An elemental-sulfur-based synthesis is reported, which, combined with processing to improve the size dispersion and passivation, results in a low-cost high-quality platform for small-bandgap PbS-CQD-based devices. Size-selective precipitation and cadmium chloride passivation are used to improve the power conversion efficiency of 1 eV bandgap CQD photovoltaic devices dramatically, which leads to record power conversion efficiency for a 1 eV PbS CQD solar cell of 5.4%. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Direct synthesis of antimicrobial coatings based on tailored bi-elemental nanoparticles

    Directory of Open Access Journals (Sweden)

    Giulio Benetti

    2017-03-01

    Full Text Available Ultrathin coatings based on bi-elemental nanoparticles (NPs are very promising to limit the surface-related spread of bacterial pathogens, particularly in nosocomial environments. However, tailoring the synthesis, composition, adhesion to substrate, and antimicrobial spectrum of the coating is an open challenge. Herein, we report on a radically new nanostructured coating, obtained by a one-step gas-phase deposition technique, and composed of bi-elemental Janus type Ag/Ti NPs. The NPs are characterized by a cluster-in-cluster mixing phase with metallic Ag nano-crystals embedded in amorphous TiO2 and present a promising antimicrobial activity including also multidrug resistant strains. We demonstrate the flexibility of the method to tune the embedded Ag nano-crystals dimension, the total relative composition of the coating, and the substrate type, opening the possibility of tailoring the dimension, composition, antimicrobial spectrum, and other physical/chemical properties of such multi-elemental systems. This work is expected to significantly spread the range of applications of NPs coatings, not only as an effective tool in the prevention of healthcare-associated infections but also in other technologically relevant fields like sensors or nano-/micro joining.

  7. Direct synthesis of antimicrobial coatings based on tailored bi-elemental nanoparticles

    Science.gov (United States)

    Benetti, Giulio; Cavaliere, Emanuele; Canteri, Adalberto; Landini, Giulia; Rossolini, Gian Maria; Pallecchi, Lucia; Chiodi, Mirco; Van Bael, Margriet J.; Winckelmans, Naomi; Bals, Sara; Gavioli, Luca

    2017-03-01

    Ultrathin coatings based on bi-elemental nanoparticles (NPs) are very promising to limit the surface-related spread of bacterial pathogens, particularly in nosocomial environments. However, tailoring the synthesis, composition, adhesion to substrate, and antimicrobial spectrum of the coating is an open challenge. Herein, we report on a radically new nanostructured coating, obtained by a one-step gas-phase deposition technique, and composed of bi-elemental Janus type Ag/Ti NPs. The NPs are characterized by a cluster-in-cluster mixing phase with metallic Ag nano-crystals embedded in amorphous TiO2 and present a promising antimicrobial activity including also multidrug resistant strains. We demonstrate the flexibility of the method to tune the embedded Ag nano-crystals dimension, the total relative composition of the coating, and the substrate type, opening the possibility of tailoring the dimension, composition, antimicrobial spectrum, and other physical/chemical properties of such multi-elemental systems. This work is expected to significantly spread the range of applications of NPs coatings, not only as an effective tool in the prevention of healthcare-associated infections but also in other technologically relevant fields like sensors or nano-/micro joining.

  8. Hybrid variational principles and synthesis method for finite element neutron transport calculations

    International Nuclear Information System (INIS)

    Ackroyd, R.T.; Nanneh, M.M.

    1990-01-01

    A family of hybrid variational principles is derived using a generalised least squares method. Neutron conservation is automatically satisfied for the hybrid principles employing two trial functions. No interfaces or reflection conditions need to be imposed on the independent even-parity trial function. For some hybrid principles a single trial function can be employed by relating one parity trial function to the other, using one of the parity transport equation in relaxed form. For other hybrid principles the trial functions can be employed sequentially. Synthesis of transport solutions, starting with the diffusion theory approximation, has been used as a way of reducing the scale of the computation that arises with established finite element methods for neutron transport. (author)

  9. Synthesis of superheavy elements and application of nuclear physics methods in related fields

    International Nuclear Information System (INIS)

    Flerov, G.

    1985-01-01

    Heavy ion accelerators are used not only for the synthesis of new elements but also for the production of nuclear filters from polymers. The principle is described of the manufacture of such filters, and their chemical processing. By changes in irradiation conditions and in conditions of chemical leaching, nuclear filters may be obtained of various density, shape and size of pores and with a different angular distribution of tracks in the polymer material. The most frequently used polymer is polyethylene terephthalate film. The uses are described of nuclear filters, such as water treatment in the production of semiconductor instruments, in cryogenic instruments, in the purification concentration and sterilization filtration of viruses and vaccines, etc. Other uses of heavy ion beams are suggested, such as the method of nuclear tracks, the manufacture of membranes with a single opening, the manufacture of laser diaphragms, lithography, etc. (E.S.)

  10. Synthesis of (±)-amathaspiramide F and discovery of an unusual stereocontrolling element for the [2,3]-Stevens rearrangement.

    Science.gov (United States)

    Soheili, Arash; Tambar, Uttam K

    2013-10-04

    A formal total synthesis of (±)-amathaspiramide F through a tandem palladium-catalyzed allylic amination/[2,3]-Stevens rearrangement is reported. The unexpected diastereoselectivity of the [2,3]-Stevens rearrangement was controlled by the substitution patterns of an aromatic ring. This discovery represents a new stereocontrolling element for [2,3]-sigmatropic rearrangements in complex molecular settings.

  11. Comprehensive coordination chemistry. The synthesis, reactions, properties and applications of coordination compounds. V.3. Main group and early transition elements

    International Nuclear Information System (INIS)

    Wilkinson, Geoffrey; Gillard, R.D.; McCleverty, J.A.

    1987-01-01

    Comprehensive coordination chemistry reviews the synthesis reactions and properties of coordination compounds. Their uses in such diverse fields as nuclear fuels, toxicology, medicine and biology are discussed. Volume three concentrates on the main group and early transition element coordination compounds. (UK)

  12. Ti-Mg alloy powder synthesis via mechanochemical reduction of TiO 2 by elemental magnesium

    CSIR Research Space (South Africa)

    Mushove, T

    2009-04-01

    Full Text Available This paper reports the preliminary results of an investigation on the synthesis of a Ti-Mg alloy powder through mechanochemical processing of TiO 2 and Mg powders. TiO 2 was mixed with elemental Mg according to a nominal stoichiometric composition...

  13. Novel big-bang element synthesis catalyzed by supersymmetric particle stau

    International Nuclear Information System (INIS)

    Kamimura, Masayasu; Kino, Yasushi; Hiyama, Emiko

    2010-01-01

    The extremely low isotope ratio of 6 Li had remained as a drawback of the Big-Bang Nucleosynthesis (BBN) until Pospelov proposed the 6 Li synthesis reaction catalyzed by negatively charged electroweak-scale particle X - in 2006. He remarked the catalytic enhancement of 6 Li production by about 10 8 times, as well as the life and initial abundance of X - . The present authors classified BBN catalyzed reaction into six types, i.e. (1) non-resonant transfer, (2) resonant transfer, (3) non-resonant radiative capture, (4) resonant radiative capture, (5) three-body breakup and (6) charge transfer reactions to predict absolute values of cross sections which cannot be observed experimentally. Starting from the three-body treatment for those reactions, 6 Li problems, the life-time and abundance of stau are discussed. Large change of element composition at 'late-time' big bang, generation of 9 Be by stau catalyzed reaction, 7 Li problem and stau catalyzed reactions are also discussed. Finally their relations with the supersymmetry theory and dark matter are mentioned. The basic nuclear calculations are providing quantitative base for the 'effect of nuclear reactions catalyzed by the supersymmetric particle stau on big bang nucleosynthesis'. (S. Funahashi)

  14. A synthesis of rates and controls on elemental mercury evasion in the Great Lakes Basin

    International Nuclear Information System (INIS)

    Denkenberger, Joseph S.; Driscoll, Charles T.; Branfireun, Brian A.; Eckley, Chris S.; Cohen, Mark; Selvendiran, Pranesh

    2012-01-01

    Rates of surface-air elemental mercury (Hg 0 ) fluxes in the literature were synthesized for the Great Lakes Basin (GLB). For the majority of surfaces, fluxes were net positive (evasion). Digital land-cover data were combined with representative evasion rates and used to estimate annual Hg 0 evasion for the GLB (7.7 Mg/yr). This value is less than our estimate of total Hg deposition to the area (15.9 Mg/yr), suggesting the GLB is a net sink for atmospheric Hg. The greatest contributors to annual evasion for the basin are agricultural (∼55%) and forest (∼25%) land cover types, and the open water of the Great Lakes (∼15%). Areal evasion rates were similar across most land cover types (range: 7.0–21.0 μg/m 2 -yr), with higher rates associated with urban (12.6 μg/m 2 -yr) and agricultural (21.0 μg/m 2 -yr) lands. Uncertainty in these estimates could be partially remedied through a unified methodological approach to estimating Hg 0 fluxes. - Highlights: ► Considerable variability exists across spatial/temporal scales in Hg 0 evasion rates. ► Methodological approaches vary for estimating and reporting gaseous Hg 0 fluxes. ► Hg 0 evasion from the Great Lakes Basin is estimated at 7.7 Mg/yr (10.2 μg/m 2 -yr). ► Hg flux estimates suggest region is a net sink for atmospheric Hg. ► 95% of Hg 0 evasion in the region is from agriculture, forest, and the Great Lakes. - A synthesis of Hg evasion was conducted and this information was used to develop an estimate of Hg evasion for the Great Lakes Basin.

  15. The 3'-terminal 55 nucleotides of bovine coronavirus defective interfering RNA harbor cis-acting elements required for both negative- and positive-strand RNA synthesis.

    Directory of Open Access Journals (Sweden)

    Wei-Yu Liao

    Full Text Available The synthesis of the negative-strand [(--strand] complement of the ∼30 kilobase, positive-strand [(+-strand] coronaviral genome is a necessary early step for genome replication. The identification of cis-acting elements required for (--strand RNA synthesis in coronaviruses, however, has been hampered due to insufficiencies in the techniques used to detect the (--strand RNA species. Here, we employed a method of head-to-tail ligation and real-time quantitative reverse transcription polymerase chain reaction (qRT-PCR to detect and quantitate the synthesis of bovine coronavirus (BCoV defective interfering (DI RNA (- strands. Furthermore, using the aforementioned techniques along with Northern blot assay, we specifically defined the cis-acting RNA elements within the 3'-terminal 55 nucleotides (nts which function in the synthesis of (-- or (+-strand BCoV DI RNA. The major findings are as follows: (i nts from -5 to -39 within the 3'-terminal 55 nts are the cis-acting elements responsible for (--strand BCoV DI RNA synthesis, (ii nts from -3 to -34 within the 3'-terminal 55 nts are cis-acting elements required for (+-strand BCoV DI RNA synthesis, and (iii the nucleotide species at the 3'-most position (-1 is important, but not critical, for both (-- and (+-strand BCoV DI RNA synthesis. These results demonstrate that the 3'-terminal 55 nts in BCoV DI RNA harbor cis-acting RNA elements required for both (-- and (+-strand DI RNA synthesis and extend our knowledge on the mechanisms of coronavirus replication. The method of head-to-tail ligation and qRT-PCR employed in the study may also be applied to identify other cis-acting elements required for (--strand RNA synthesis in coronaviruses.

  16. Upper Limit of the Periodic Table and Synthesis of Superheavy Elements

    Directory of Open Access Journals (Sweden)

    Khazan A.

    2007-04-01

    Full Text Available For the first time, using the heaviest possible element, the diagram for known nuclides and stable isotopes is constructed. The direction of search of superheavy elements is indicated. The Periodic Table with an eighth period is tabulated.

  17. Identification of cis-acting elements on positive-strand subgenomic mRNA required for the synthesis of negative-strand counterpart in bovine coronavirus.

    Science.gov (United States)

    Yeh, Po-Yuan; Wu, Hung-Yi

    2014-07-30

    It has been demonstrated that, in addition to genomic RNA, sgmRNA is able to serve as a template for the synthesis of the negative-strand [(-)-strand] complement. However, the cis-acting elements on the positive-strand [(+)-strand] sgmRNA required for (-)-strand sgmRNA synthesis have not yet been systematically identified. In this study, we employed real-time quantitative reverse transcription polymerase chain reaction to analyze the cis-acting elements on bovine coronavirus (BCoV) sgmRNA 7 required for the synthesis of its (-)-strand counterpart by deletion mutagenesis. The major findings are as follows. (1) Deletion of the 5'-terminal leader sequence on sgmRNA 7 decreased the synthesis of the (-)-strand sgmRNA complement. (2) Deletions of the 3' untranslated region (UTR) bulged stem-loop showed no effect on (-)-strand sgmRNA synthesis; however, deletion of the 3' UTR pseudoknot decreased the yield of (-)-strand sgmRNA. (3) Nucleotides positioned from -15 to -34 of the sgmRNA 7 3'-terminal region are required for efficient (-)-strand sgmRNA synthesis. (4) Nucleotide species at the 3'-most position (-1) of sgmRNA 7 is correlated to the efficiency of (-)-strand sgmRNA synthesis. These results together suggest, in principle, that the 5'- and 3'-terminal sequences on sgmRNA 7 harbor cis-acting elements are critical for efficient (-)-strand sgmRNA synthesis in BCoV.

  18. Organotrichlorogermane synthesis by the reaction of elemental germanium, tetrachlorogermane and organic chloride via dichlorogermylene intermediate.

    Science.gov (United States)

    Okamoto, Masaki; Asano, Takuya; Suzuki, Eiichi

    2004-08-07

    Organotrichlorogermanes were synthesized by the reaction of elemental germanium, tetrachlorogermane and organic chlorides, methyl, propyl, isopropyl and allyl chlorides. Dichlorogermylene formed by the reaction of elemental germanium with tetrachlorogermane was the reaction intermediate, which was inserted into the carbon-chlorine bond of the organic chloride to give organotrichlorogermane. When isopropyl or allyl chloride was used as an organic chloride, organotrichlorogermane was formed also in the absence of tetrachlorogermane. These chlorides were converted to hydrogen chloride, which subsequently reacted with elemental germanium to give the dichlorogermylene intermediate. The reaction of elemental germanium, tetrachlorogermane and organic chlorides provides a simple and easy method for synthesizing organotrichlorogermanes, and all the raw materials are easily available.

  19. Synthesis and assessment of imprinted polymers for the separation of f elements. Application to liquid chromatography

    International Nuclear Information System (INIS)

    Vigneau, Olivier

    2002-01-01

    Within the frame of the CEA's SPIN programme which aims at separate lanthanides (Ln) and actinides (An) in order to decrease the volume and activity of nuclear wastes to be stored, and after a presentation of lanthanides and actinides, of the main methods of inter-group and intra-group separation, this research thesis presents the principles and applications of the molecular print and ionic print which are then used to perform the Ln/Ln and Ln/an separation. The author discusses the choice and synthesis of selective complexing monomers which are used for the synthesis of imprinted polymers. The next chapter reports the synthesis of imprinted polymers, the assessment of their properties (selectivity and extraction power) in Ln/Ln competitive extraction in a batch reactor, and the optimization of synthesis conditions. Then, the author reports the assessment of properties of imprinted material in terms of ability to perform an inter-group Am 241 / Eu 152 separation in a batch reactor. The last part addresses Ln/Ln separation by High Performance Liquid Chromatography by using synthesised imprinted polymers as steady phase [fr

  20. Finite-Element Model-Based Design Synthesis of Axial Flux PMBLDC Motors

    DEFF Research Database (Denmark)

    Fasil, Muhammed; Mijatovic, Nenad; Jensen, Bogi Bech

    2016-01-01

    of a unique solution. The designer can later select a design, based on comparing parameters of the designs, which are critical to the application that the motor will be used. The presented approach makes it easier to define constraints for a design synthesis problem. A detailed description of the setting up...

  1. Reaction mechanisms for the synthesis of the heaviest elements from heavy ion reactions

    International Nuclear Information System (INIS)

    Gaeggeler, H.W.

    1988-10-01

    This review paper concerns fusion reactions with light heavy-ions, cold fusion, transfer reactions using light heavy-ions or heavy ions. In two appendices, methods for the separation and detection of nuclides in the domain of heaviest elements are described and a comment on the discovery of the element 104 is given. 51 figs., 10 tabs., 335 refs

  2. Synthesis and crystal chemistry of transuranium element chalcogenides. Contribution to the study of the 5f electron localization

    International Nuclear Information System (INIS)

    Damien, Daniel.

    1976-09-01

    The synthesis and crystal chemistry of Np, Pu, Am and Cm transuranium element chalcogenides are described. From plutonium, transuranium element chalcogenides exhibit the same crystal structure as their rare-earth homologues. The variations of the lattice constants of these compounds in terms of the atomic number are characterized by the lack of the 5f contraction and are interpreted by a localization of the 5f electrons depending upon the considered transuranium element, the nature of the ligand and the crystal structure. To compare the degree of magnitude of the 5f electron delocalization in various compounds, a delocalization scale is proposed based on a comparison between the molar volumes of actinide and isostructural lanthanide compounds. This scale provides a delocalization coefficient for each compound under study. Examination of these coefficients shows that the 5f electrons, in series of actinide compounds, become localized when going from neptunium to curium and that the delocalization process does not only depend upon overlaps between 5f-6d orbitals of neighbouring actinide atoms; the delocalization coefficients show the existence of a secondary delocalization effect due to overlaps between the p anion and f actinide orbitals which are more important for the Vb anion group (N, P, As, Sb) than for the Vib one (S,Se,Te) [fr

  3. Studies on the synthesis of isotopes of superheavy element Lv (Z = 116)

    Energy Technology Data Exchange (ETDEWEB)

    Santhosh, K.P.; Safoora, V. [Kannur University, School of Pure and Applied Physics, Payyanur (India)

    2017-11-15

    The probable projectile-target combinations for the synthesis of superheavy nucleus {sup 296}Lv found in the cold valley of {sup 296}Lv have been identified by studying the interaction barrier of the colliding nuclei, probability of compound nucleus formation, P{sub CN}, and survival probability W{sub sur}. At energies near and above the Coulomb barrier, the capture, fusion and evaporation residue (ER) cross sections for the probable combinations for the hot and cold fusion reactions are systematically investigated. By considering intensities of the projectile beams, availabilities of the targets and half lives of the colliding nuclei, the combination {sup 48}Ca + {sup 248}Cm is found to be the most probable projectile-target pair for the synthesis of {sup 296}Lv. The calculated maximum value of 2n, 3n, 4n and 5n channel cross section for the reaction {sup 48}Ca + {sup 248}Cm are 0.599 pb, 5.957 pb, 4.805 pb, and 0.065 pb, respectively. Moreover, the production cross sections for the synthesis of isotopes {sup 291-295,298}Lv using {sup 48}Ca projectile on {sup 243-247,250}Cm targets are calculated. Among these reactions, the reactions {sup 48}Ca + {sup 247}Cm → {sup 295}Lv and {sup 48}Ca + {sup 250}Cm → {sup 298}Lv have maximum production cross section in 3n (10.697 pb) and 4n (12.006 pb) channel, respectively. Our studies on the SHE Lv using the combinations {sup 48}Ca + {sup 245}Cm → {sup 293}Lv and {sup 48}Ca + {sup 248}Cm → {sup 296}Lv are compared with available experimental data and with other theoretical studies. Our studies are in agreement with experimental data and we hope that these studies will be a guide for the future experiments to synthesize the isotopes of Lv. (orig.)

  4. Synthesis and Characterization of EDTA Complexes Useful for Trace Elements Supplementation

    Directory of Open Access Journals (Sweden)

    Baran Enrique J.

    2002-01-01

    Full Text Available The synthesis of two heterobimetallic EDTA complexes, MgCu(EDTA.6H2O and ZnCu(EDTA.6H2O, is described. They were characterized by means of vibrational (infrared and Raman and electronic (reflectance spectroscopy. Several dissolution tests in 0.1 N HCl and simulated gastric juice were also performed. The results support the potential usefulness of these complexes for copper supplementation in human and veterinary medicine and to the simultaneous reinforcement of Mg(II and Zn(II levels.

  5. Sterol regulatory element binding protein and dietary lipid regulation of fatty acid synthesis in the mammary epithelium.

    Science.gov (United States)

    Rudolph, Michael C; Monks, Jenifer; Burns, Valerie; Phistry, Meridee; Marians, Russell; Foote, Monica R; Bauman, Dale E; Anderson, Steven M; Neville, Margaret C

    2010-12-01

    The lactating mammary gland synthesizes large amounts of triglyceride from fatty acids derived from the blood and from de novo lipogenesis. The latter is significantly increased at parturition and decreased when additional dietary fatty acids become available. To begin to understand the molecular regulation of de novo lipogenesis, we tested the hypothesis that the transcription factor sterol regulatory element binding factor (SREBF)-1c is a primary regulator of this system. Expression of Srebf1c mRNA and six of its known target genes increased ≥2.5-fold at parturition. However, Srebf1c-null mice showed only minor deficiencies in lipid synthesis during lactation, possibly due to compensation by Srebf1a expression. To abrogate the function of both isoforms of Srebf1, we bred mice to obtain a mammary epithelial cell-specific deletion of SREBF cleavage-activating protein (SCAP), the SREBF escort protein. These dams showed a significant lactation deficiency, and expression of mRNA for fatty acid synthase (Fasn), insulin-induced gene 1 (Insig1), mitochondrial citrate transporter (Slc25a1), and stearoyl-CoA desaturase 2 (Scd2) was reduced threefold or more; however, the mRNA levels of acetyl-CoA carboxylase-1α (Acaca) and ATP citrate lyase (Acly) were unchanged. Furthermore, a 46% fat diet significantly decreased de novo fatty acid synthesis and reduced the protein levels of ACACA, ACLY, and FASN significantly, with no change in their mRNA levels. These data lead us to conclude that two modes of regulation exist to control fatty acid synthesis in the mammary gland of the lactating mouse: the well-known SREBF1 system and a novel mechanism that acts at the posttranscriptional level in the presence of SCAP deletion and high-fat feeding to alter enzyme protein.

  6. Identification of Cis-Acting Elements on Positive-Strand Subgenomic mRNA Required for the Synthesis of Negative-Strand Counterpart in Bovine Coronavirus

    Directory of Open Access Journals (Sweden)

    Po-Yuan Yeh

    2014-07-01

    Full Text Available It has been demonstrated that, in addition to genomic RNA, sgmRNA is able to serve as a template for the synthesis of the negative-strand [(−-strand] complement. However, the cis-acting elements on the positive-strand [(+-strand] sgmRNA required for (−-strand sgmRNA synthesis have not yet been systematically identified. In this study, we employed real-time quantitative reverse transcription polymerase chain reaction to analyze the cis-acting elements on bovine coronavirus (BCoV sgmRNA 7 required for the synthesis of its (−-strand counterpart by deletion mutagenesis. The major findings are as follows. (1 Deletion of the 5'-terminal leader sequence on sgmRNA 7 decreased the synthesis of the (−-strand sgmRNA complement. (2 Deletions of the 3' untranslated region (UTR bulged stem-loop showed no effect on (−-strand sgmRNA synthesis; however, deletion of the 3' UTR pseudoknot decreased the yield of (−-strand sgmRNA. (3 Nucleotides positioned from −15 to −34 of the sgmRNA 7 3'-terminal region are required for efficient (−-strand sgmRNA synthesis. (4 Nucleotide species at the 3'-most position (−1 of sgmRNA 7 is correlated to the efficiency of (−-strand sgmRNA synthesis. These results together suggest, in principle, that the 5'- and 3'-terminal sequences on sgmRNA 7 harbor cis-acting elements are critical for efficient (−-strand sgmRNA synthesis in BCoV.

  7. Primer-Independent DNA Synthesis by a Family B DNA Polymerase from Self-Replicating Mobile Genetic Elements

    Directory of Open Access Journals (Sweden)

    Modesto Redrejo-Rodríguez

    2017-11-01

    Full Text Available Family B DNA polymerases (PolBs play a central role during replication of viral and cellular chromosomes. Here, we report the discovery of a third major group of PolBs, which we denote primer-independent PolB (piPolB, that might be a link between the previously known protein-primed and RNA/DNA-primed PolBs. PiPolBs are encoded by highly diverse mobile genetic elements, pipolins, integrated in the genomes of diverse bacteria and also present as circular plasmids in mitochondria. Biochemical characterization showed that piPolB displays efficient DNA polymerization activity that can use undamaged and damaged templates and is endowed with proofreading and strand displacement capacities. Remarkably, the protein is also capable of template-dependent de novo DNA synthesis, i.e., DNA-priming activity, thereby breaking the long-standing dogma that replicative DNA polymerases require a pre-existing primer for DNA synthesis. We suggest that piPolBs are involved in self-replication of pipolins and may also contribute to bacterial DNA damage tolerance.

  8. Role of the Pepino mosaic virus 3'-untranslated region elements in negative-strand RNA synthesis in vitro.

    Science.gov (United States)

    Osman, Toba A M; Olsthoorn, René C L; Livieratos, Ioannis C

    2014-09-22

    Pepino mosaic virus (PepMV) is a mechanically-transmitted positive-strand RNA potexvirus, with a 6410 nt long single-stranded (ss) RNA genome flanked by a 5'-methylguanosine cap and a 3' poly-A tail. Computer-assisted folding of the 64 nt long PepMV 3'-untranslated region (UTR) resulted in the prediction of three stem-loop structures (hp1, hp2, and hp3 in the 3'-5' direction). The importance of these structures and/or sequences for promotion of negative-strand RNA synthesis and binding to the RNA dependent RNA polymerase (RdRp) was tested in vitro using a specific RdRp assay. Hp1, which is highly variable among different PepMV isolates, appeared dispensable for negative-strand synthesis. Hp2, which is characterized by a large U-rich loop, tolerated base-pair changes in its stem as long as they maintained the stem integrity but was very sensitive to changes in the U-rich loop. Hp3, which harbours the conserved potexvirus ACUUAA hexamer motif, was essential for template activity. Template-RNA polymerase binding competition experiments showed that the ACUUAA sequence represents a high-affinity RdRp binding element. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Purposeful synthesis of chemical elements and ecologically pure mobile sources of energy

    International Nuclear Information System (INIS)

    Krivitsky, V. A.; Gareev, F. A.

    2007-01-01

    It is well known [1] that the natural geo-transmutation of chemical elements occurs in the atmosphere and earth in the regions of a strong change in geo-, bio-, acoustic-, and electromagnetic fields. The mineral row materials contain the same accompanying chemical combinations which are independent of mineral deposit [2]. This means that the formation of chemical elements occurs in the same physical and chemical conditions. These conditions were simulated on the fundamental cooperative resonance synchronization principle [1]. The experimental facility was constructed on the basis of our model which provided with the calculated final chemical elements. These experimental results indicate new possibilities for, simulating, inducing and controlling nuclear reactions by low energy external fields. The borrowing from the geo-transmutation mechanisms of chemical elements creates the fundamental directions in low energy nuclear reaction researches for construction of new ecologically pure mobile sources of energy independent of oil, gas and coal, new substances, and technologies. References [1] F.A. Gareev, I.E. Zhidkova, E-print arXiv Nucl-th/0610002 2006. [2] V.A. Krivzskii, Transmutazija ximicheskix elementov v evolyuzii Semli (in Russian), Moscow 2003

  10. Synthesis Report on the understanding of failed LMFBR fuel element performance

    International Nuclear Information System (INIS)

    Plitz, H.; Bagley, K.; Harbourne, B.

    1990-07-01

    In the coarse of LMFBR operation fuel element failures cannot entirely be avoided as experienced during the operation of PFR, PHENIX and KNK II, where 44 failed fuel elements have been registered between 1978 and 1989. In earlier irradiations, post irradiation examinations showed mixed oxide pin diameter increases up to pin pitch distance, urging to stress reactor safety questions on the potential of fuel pin failure propagation within pin bundles. The chemical interaction of sodium with mixed oxide fuel is regarded to be the key for the understanding of failed fuel behavior. Valuable results on the failed fuel pin behavior during operation were obtained from the SILOE sodium loop test. Based on the bulk of experience with the detection of fuel pin failures, with the continued operation and with the handling of failed pins respectively elements, one can state: 1. All fuel pin failures have been detected securely in time and have been located. 2. Small defects are developing slowly. 3. Even large defects at end-of-life pins resulted in limited fuel loss. 4. Clad failures behave benign in main aspects. 5. The chemical interaction of sodium with mixed oxide is an important factor in the behavior of failed fuel pins, especially at high burnup. 6. Despite different pin designs and different operation conditions, on the basis of 44 failed elements in PFR, PHENIX and KNK II no pin-to-pin propagation was observed and fuel release was rather low, often not detectable. 7. In no case hazard conditions affecting reactor safety have been experienced

  11. Synthesis and properties of neutron deficient isotopes of elements around Z=100

    International Nuclear Information System (INIS)

    Antalic, S.

    2005-01-01

    In the presented Thesis work the results of spectroscopic studies of 246 Md, 247 Md, 254 Lr and 255 Lr decay chains are given. These isotopes were produced using heavy ion induced fusion reactions of 40 Ar + 209 Bi and 48 Ca + 209 Bi as a part of the long term project aimed to study spectroscopy properties of superheavy elements. The experiments were performed at velocity filter SHIP, placed at the central beam line of the UNILAC accelerator at GSI Darmstadt in Germany. The work also gives a basic overview of research in the region of superheavy elements, description of the used experimental setup and shows the usual analysis methods used in spectroscopic studies in the region of elements around Z ∼ 100. The results were obtained using α, α - γ spectroscopy methods and recoil - α, α - α correlations search. Although these isotopes have been known for a longer time, no detailed spectroscopy investigation were performed so far and only rough information was known. Beside the improved precision of known data, this work gives a new information about the decay properties of these isotopes. This give us the possibility to build a decay schemes for mentioned decay chains. (author)

  12. Assessing elements of an extended evolutionary synthesis for plant domestication and agricultural origin research

    Science.gov (United States)

    Piperno, Dolores R.

    2017-01-01

    The development of agricultural societies, one of the most transformative events in human and ecological history, was made possible by plant and animal domestication. Plant domestication began 12,000–10,000 y ago in a number of major world areas, including the New World tropics, Southwest Asia, and China, during a period of profound global environmental perturbations as the Pleistocene epoch ended and transitioned into the Holocene. Domestication is at its heart an evolutionary process, and for many prehistorians evolutionary theory has been foundational in investigating agricultural origins. Similarly, geneticists working largely with modern crops and their living wild progenitors have documented some of the mechanisms that underwrote phenotypic transformations from wild to domesticated species. Ever-improving analytic methods for retrieval of empirical data from archaeological sites, together with advances in genetic, genomic, epigenetic, and experimental research on living crop plants and wild progenitors, suggest that three fields of study currently little applied to plant domestication processes may be necessary to understand these transformations across a range of species important in early prehistoric agriculture. These fields are phenotypic (developmental) plasticity, niche construction theory, and epigenetics with transgenerational epigenetic inheritance. All are central in a controversy about whether an Extended Evolutionary Synthesis is needed to reconceptualize how evolutionary change occurs. An exploration of their present and potential utility in domestication study shows that all three fields have considerable promise in elucidating important issues in plant domestication and in agricultural origin and dispersal research and should be increasingly applied to these issues. PMID:28576881

  13. Synthesis and release of trace elements from hollow and porous hydroxyapatite spheres

    International Nuclear Information System (INIS)

    Xia Wei; Grandfield, Kathryn; Schwenke, Almut; Engqvist, Haakan

    2011-01-01

    It is known that organic species regulate fabrication of hierarchical biological forms via solution methods. However, in this study, we observed that the presence of inorganic ions plays an important role in the formation and regulation of biological spherical hydroxyapatite formation. We present a mineralization method to prepare ion-doped hydroxyapatite spheres with a hierarchical structure that is free of organic surfactants and biological additives. Porous and hollow strontium-doped hydroxyapatite spheres were synthesized via controlling the concentration of strontium ions in a calcium and phosphate buffer solution. Similarly, fluoride and silicon-doped hydroxyapatite spheres were synthesized. While spherical particle formation was attainable at low and high temperature for Sr-doped hydroxyapatite, it was only possible at high temperature in the F/Si-doped system. The presence of inorganic ions not only plays an important role in the formation and regulation of biological spherical hydroxyapatite, but also could introduce pharmaceutical effects as a result of trace element release. Such ion release results showed a sustained release with pH responsive behavior, and significantly influenced the hydroxyapatite re-precipitation. These ion-doped hydroxyapatite spheres with hollow and porous structure could have promising applications as bone/tooth materials, drug delivery systems, and chromatography supports.

  14. Elemental depth profiles and plasma etching rates of positive-tone electron beam resists after sequential infiltration synthesis of alumina

    Science.gov (United States)

    Ozaki, Yuki; Ito, Shunya; Hiroshiba, Nobuya; Nakamura, Takahiro; Nakagawa, Masaru

    2018-06-01

    By scanning transmission electron microscopy and energy dispersive X-ray spectroscopy (STEM–EDS), we investigated the elemental depth profiles of organic electron beam resist films after the sequential infiltration synthesis (SIS) of inorganic alumina. Although a 40-nm-thick poly(methyl methacrylate) (PMMA) film was entirely hybridized with alumina, an uneven distribution was observed near the interface between the substrate and the resist as well as near the resist surface. The uneven distribution was observed around the center of a 100-nm-thick PMMA film. The thicknesses of the PMMA and CSAR62 resist films decreased almost linearly as functions of plasma etching period. The comparison of etching rate among oxygen reactive ion etching, C3F8 reactive ion beam etching (RIBE), and Ar ion beam milling suggested that the SIS treatment enhanced the etching resistance of the electron beam resists to chemical reactions rather than to ion collisions. We proposed oxygen- and Ar-assisted C3F8 RIBE for the fabrication of silica imprint molds by electron beam lithography.

  15. Discrete element method based scale-up model for material synthesis using ball milling

    Science.gov (United States)

    Santhanam, Priya Radhi

    Mechanical milling is a widely used technique for powder processing in various areas. In this work, a scale-up model for describing this ball milling process is developed. The thesis is a combination of experimental and modeling efforts. Initially, Discrete Element Model (DEM) is used to describe energy transfer from milling tools to the milled powder for shaker, planetary, and attritor mills. The rolling and static friction coefficients are determined experimentally. Computations predict a quasisteady rate of energy dissipation, E d, for each experimental configuration. It is proposed that the milling dose defined as a product of Ed and milling time, t, divided by the mass of milled powder, mp characterizes the milling progress independently of the milling device or milling conditions used. Once the milling dose is determined for one experimental configuration, it can be used to predict the milling time required to prepare the same material in any milling configuration, for which Ed is calculated. The concept is validated experimentally for DEM describing planetary and shaker mills. For attritor, the predicted Ed includes substantial contribution from milling tool interaction events with abnormally high forces (>103 N). The energy in such events is likely dissipated to heat or plastically deform milling tools rather than refine material. Indeed, DEM predictions for the attritor correlate with experiments when such events are ignored in the analysis. With an objective of obtaining real-time indicators of milling progress, power, torque, and rotation speed of the impeller of an attritor mill are measured during preparation of metal matrix composite powders in the subsequent portion of this thesis. Two material systems are selected and comparisons made between in-situ parameters and experimental milling progress indicators. It is established that real-time measurements can certainly be used to describe milling progress. However, they need to be interpreted carefully

  16. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Directory of Open Access Journals (Sweden)

    Lkhamsuren Bayarjargal

    2011-09-01

    Full Text Available Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p; T stability, compressibility and hardness is described as obtained from experiments.

  17. Synthesis of Binary Transition Metal Nitrides, Carbides and Borides from the Elements in the Laser-Heated Diamond Anvil Cell and Their Structure-Property Relations

    Science.gov (United States)

    Friedrich, Alexandra; Winkler, Björn; Juarez-Arellano, Erick A.; Bayarjargal, Lkhamsuren

    2011-01-01

    Transition metal nitrides, carbides and borides have a high potential for industrial applications as they not only have a high melting point but are generally harder and less compressible than the pure metals. Here we summarize recent advances in the synthesis of binary transition metal nitrides, carbides and borides focusing on the reaction of the elements at extreme conditions generated within the laser-heated diamond anvil cell. The current knowledge of their structures and high-pressure properties like high-(p,T) stability, compressibility and hardness is described as obtained from experiments. PMID:28824101

  18. Transactinide elements

    International Nuclear Information System (INIS)

    Hemingway, J.D.

    1975-01-01

    The review is covered in sections, entitled: predicted nuclear properties - including closed shells, decay characteristics; predicted chemical properties - including electronic structure and calculated properties, X-radiation, extrapolated chemical properties, separation chemistry; methods of synthesis; the natural occurrence of superheavy elements. (U.K.)

  19. β-Hydroxybutyrate Facilitates Fatty Acids Synthesis Mediated by Sterol Regulatory Element-Binding Protein1 in Bovine Mammary Epithelial Cells

    Directory of Open Access Journals (Sweden)

    Min Zhang

    2015-11-01

    Full Text Available Background/Aims: In dairy cows, β-hydroxybutyrate (BHBA is utilized as precursors of de novo synthesized fatty acids in mammary gland. Ketotic cows are characterized by excessive negative energy balance (NEB, which can further increase the blood BHBA concentration. Sterol regulatory element-binding protein1 (SREBP1 and cell death-inducing DNA fragmentation factor-alpha-like effector α (Cidea play crucial roles in lipid synthesis. Therefore, we hypothesized that BHBA could stimulate SREBP1/Cidea pathway to increase milk fat synthesis in bovine mammary epithelial cells. Methods: Bovine mammary epithelial cells were treated with different concentrations of BHBA and transfected with adenovirus to silence SREBP1 expression. The effects of BHBA on the lipid synthesis in bovine mammary epithelial cells were investigated. Results: The results showed that BHBA could significantly increase the expression of SREBP1, fatty acid synthase (FAS, acetyl-CoA carboxylase α (ACC-α, Cidea and diacylglycerol transferase-1 (DGAT-1, as well as the triglycerides (TG content in bovine mammary epithelial cells. BHBA treatment also increased the transfer of mature SREBP1 to nucleus compared with control group. However, SREBP1 silencing could significantly down-regulate the overexpression of FAS, ACC-α, Cidea and DGAT-1, as well as TG content induced by BHBA. Conclusion: The present data indicate that BHBA can significantly increase TG secretion mediated by SREBP1 in bovine mammary epithelial cells.

  20. A Novel Synthesis Routine for Woodwardite and Its Affinity towards Light (La, Ce, Nd and Heavy (Gd and Y Rare Earth Elements

    Directory of Open Access Journals (Sweden)

    Sirio Consani

    2018-01-01

    Full Text Available A synthetic Cu-Al-SO4 layered double hydroxide (LDH, analogue to the mineral woodwardite [Cu1−xAlx(SO4x/2(OH2·nH2O], with x < 0.5 and n ≤ 3x/2, was synthesised by adding a solution of Cu and Al sulphates to a solution with NaOH. The pH values were kept constant at 8.0 and 10.0 by a continuous addition of NaOH. The material obtained had poor crystallinity, turbostratic structure, and consisted of nanoscopic crystallites. The analyses performed in order to characterise the obtained materials (X-ray diffraction (XRD, thermogravimetry (TG, and Fourier Transform Infra-Red (FTIR spectroscopy showed that the Cu-Al-SO4 LDH is very similar to woodwardite, although it has a smaller layer spacing, presumably due to a lesser water content than in natural samples. The synthesis was performed by adding light rare earth elements (LREEs (La, Ce, and Nd and heavy rare earth elements (HREEs (Gd and Y in order to test the affinity of the Cu-Al-SO4 LDH to the incorporation of REEs. The concentration of rare earth elements (REEs in the solid fraction was in the range of 3.5–8 wt %. The results showed a good affinity for HREE and Nd, especially for materials synthesised at pH 10.0, whereas the affinities for Ce and La were much lower or non-existent. The thermal decomposition of the REE-doped materials generates a mixture of Cu, Al, and REE oxides, making them interesting as precursors in REE oxide synthesis.

  1. Component mode synthesis methods applied to 3D heterogeneous core calculations, using the mixed dual finite element solver MINOS

    Energy Technology Data Exchange (ETDEWEB)

    Guerin, P.; Baudron, A. M.; Lautard, J. J. [Commissariat a l' Energie Atomique, DEN/DANS/DM2S/SERMA/LENR, CEA Saclay, 91191 Gif sur Yvette (France)

    2006-07-01

    This paper describes a new technique for determining the pin power in heterogeneous core calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions: in the first one (Component Mode Synthesis method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (Factorized Component Mode Synthesis method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well-fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher order angular approximations - particularly easily to a SPN approximation - the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with UOX and MOX assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

  2. Component mode synthesis methods applied to 3D heterogeneous core calculations, using the mixed dual finite element solver MINOS

    International Nuclear Information System (INIS)

    Guerin, P.; Baudron, A. M.; Lautard, J. J.

    2006-01-01

    This paper describes a new technique for determining the pin power in heterogeneous core calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions: in the first one (Component Mode Synthesis method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (Factorized Component Mode Synthesis method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well-fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher order angular approximations - particularly easily to a SPN approximation - the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with UOX and MOX assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

  3. Sterols regulate 3β-hydroxysterol Δ24-reductase (DHCR24) via dual sterol regulatory elements: cooperative induction of key enzymes in lipid synthesis by Sterol Regulatory Element Binding Proteins.

    Science.gov (United States)

    Zerenturk, Eser J; Sharpe, Laura J; Brown, Andrew J

    2012-10-01

    3β-Hydroxysterol Δ24-reductase (DHCR24) catalyzes a final step in cholesterol synthesis, and has been ascribed diverse functions, such as being anti-apoptotic and anti-inflammatory. How this enzyme is regulated transcriptionally by sterols is currently unclear. Some studies have suggested that its expression is regulated by Sterol Regulatory Element Binding Proteins (SREBPs) while another suggests it is through the Liver X Receptor (LXR). However, these transcription factors have opposing effects on cellular sterol levels, so it is likely that one predominates. Here we establish that sterol regulation of DHCR24 occurs predominantly through SREBP-2, and identify the particular region of the DHCR24 promoter to which SREBP-2 binds. We demonstrate that sterol regulation is mediated by two sterol regulatory elements (SREs) in the promoter of the gene, assisted by two nearby NF-Y binding sites. Moreover, we present evidence that the dual SREs work cooperatively to regulate DHCR24 expression by comparison to two known SREBP target genes, the LDL receptor with one SRE, and farnesyl-diphosphate farnesyltransferase 1, with two SREs. Copyright © 2012 Elsevier B.V. All rights reserved.

  4. Environmental Guide Value (VGE) and specific reference values (QS) for uranium. Synthesis and elements for application to French fresh waters

    International Nuclear Information System (INIS)

    2015-01-01

    This report proposes a synthesis of works performed to determine criteria of protection of continental aquatic ecosystems with respect to uranium. These works resulted in the determination of an environmental guide value (VGE) for the assessment of the ecological and chemical condition of waters. Other specific reference values have been determined to be used in risk assessment: average annual concentration, maximum admissible concentration. After a recall of the methodology adopted for the determination of VGE in the case of uranium, the report discusses the specific reference values in the case of uranium for different organisms, for predators, for the protection of human health against a risk of exposure by consumption of fished products or drinkable water. The determination of VGE and its application are reported, and its consistency with the criterion of radiation protection of the environment applied to water and sediments is discussed. The determination of specific reference values is then discussed

  5. Synthesis of the isotopes of elements 118 and 116 in the 249Cf and 245Cm+48Ca fusion reactions

    International Nuclear Information System (INIS)

    Oganessian, Y T; Utyonkov, V K; Lobanov, Y V; Abdullin, F S; Polyakov, A N; Sagaidak, R N; Shirokovsky, I V; Tsyganov, Y S; Voinov, A A; Gulbekian, G G; Bogomolov, S L; Gikal, B N; Mezentsev, A N; Iliev, S; Subbotin, V G; Sukhov, A M; Subotic, K; Zagrebaev, V I; Vostokin, G K; Itkis, M G; Moody, K J; . Patin, J B; Shaughnessy, D A; Stoyer, M A; Stoyer, N J; Wilk, P A; Kenneally, J M; Landrum, J H; Wild, J F; Lougheed, R W

    2006-01-01

    The decay properties of 290 116 and 291 116, and the dependence of their production cross sections on the excitation energies of the compound nucleus, 293 116, have been measured in the 245 Cm( 48 Ca,xn) 293-x 116 reaction. These isotopes of element 116 are the decay daughters of element 118 isotopes, which are produced via the 249 Cf+ 48 Ca reaction. They performed the element 118 experiment at two projectile energies, corresponding to 297 118 compound nucleus excitation energies of E* = 29.2 ± 2.5 and 34.4 ± 2.3 MeV. During an irradiation with a total beam dose of 4.1 x 10 19 48 Ca projectiles, three similar decay chains consisting of two or three consecutive α decays and terminated by a spontaneous fission (SF) with high total kinetic energy of about 230 MeV were observed. The three decay chains originated from the even-even isotope 294 118 (E α = 11.65 ± 0.06 MeV, T α = 0.89 -0.31 +1.07 ms) produced in the 3n-evaporation channel of the 249 Cf+ 48 Ca reaction with a maximum cross section of 0.5 -0.3 +1.6 pb

  6. Component mode synthesis methods for 3-D heterogeneous core calculations applied to the mixed-dual finite element solver MINOS

    International Nuclear Information System (INIS)

    Guerin, P.; Baudron, A.M.; Lautard, J.J.; Van Criekingen, S.

    2007-01-01

    This paper describes a new technique for determining the pin power in heterogeneous three-dimensional calculations. It is based on a domain decomposition with overlapping sub-domains and a component mode synthesis (CMS) technique for the global flux determination. Local basis functions are used to span a discrete space that allows fundamental global mode approximation through a Galerkin technique. Two approaches are given to obtain these local basis functions. In the first one (the CMS method), the first few spatial eigenfunctions are computed on each sub-domain, using periodic boundary conditions. In the second one (factorized CMS method), only the fundamental mode is computed, and we use a factorization principle for the flux in order to replace the higher-order Eigenmodes. These different local spatial functions are extended to the global domain by defining them as zero outside the sub-domain. These methods are well fitted for heterogeneous core calculations because the spatial interface modes are taken into account in the domain decomposition. Although these methods could be applied to higher-order angular approximations-particularly easily to an SPN approximation-the numerical results we provide are obtained using a diffusion model. We show the methods' accuracy for reactor cores loaded with uranium dioxide and mixed oxide assemblies, for which standard reconstruction techniques are known to perform poorly. Furthermore, we show that our methods are highly and easily parallelizable. (authors)

  7. The Synthesis of the Elements The Astrophysical Quest for Nucleosynthesis and What It Can Tell Us About the Universe

    CERN Document Server

    Shaviv, Giora

    2012-01-01

    This book describes the origins and evolution of the chemical elements  we and the cosmos are made of. The story starts with the discovery of the common elements on Earth and their subsequent discovery in space. How do we learn the composition of the distant stars? How did progress in quantum theory, nuclear physics, spectroscopy, stellar structure and evolution, together with observations of stars, converge to provide an incredibly detailed picture of the universe? How does research in the micro-world explain the macro-world? How does progress in one affect the other, or lack of knowledge in one inhibit progress in the other? In short, Shaviv describes how we discovered the various pieces of the jigsaw that form our present picture of the universe; and how we sometimes put these in the wrong place before finding in the right one. En route we meet some fascinating personalities and learn about heated controversies. Shaviv shows how science lurched from one dogma  to the next, time and again shattering much ...

  8. Experiments on the Synthesis of Element 115 in the Reaction ^{243}Am (^{48}Ca, xn)^{291-x}115

    CERN Document Server

    Oganessian, Yu T; Lobanov, Yu V; Abdullin, F S; Polyakov, A N; Shirokovsky, I V; Tsyganov, Yu S; Gulbekyan, G G; Bogomolov, S L; Mezentsev, A N; Iliev, S; Subbotin, V G; Sukhov, A M; Voinov, A A; Buklanov, G V; Subotic, K M; Zagrebaev, V I; Itkis, M G; Patin, J B; Moody, K J; Wild, J F; Stoyer, M A; Stoyer, N J; Shaughnessy, D A; Kenneally, J M; Lougheed, R W

    2003-01-01

    The results of experiments designed to synthesize element 115 isotopes in the ^{243}Am(^{48}Ca,xn)^{291-x}115 reaction are presented. With a beam dose of 4.3\\cdot 10^{18} 248-Mev ^{48}Ca projectiles, we observed three similar decay chains consisting of five consecutive alpha-decays, all detected in time intervals of about 20 s and terminated at a later time by a spontaneous fission with a high energy release (TKE \\sim 220 MeV). At a higher bombarding energy of 253 MeV, with an equal ^{48}Ca beam dose, we registered a different decay chain of four consecutive alpha-decays detected in a time interval of about 0.5 s, also terminated by spontaneous fission. The alpha-decay energies and half-lives for nine new alpha-decaying nuclei were determined. The decay properties of these synthesized nuclei are consistent with consecutive alpha-decays originating from the parent isotopes of the new element 115, ^{288}115 and ^{287}115, produced in the 3n- and 4n-evaporation channels with cross sections of about 3 and 1 pb, r...

  9. F-element metalated dipyrrins: synthesis and characterization of a family of uranyl bis(dipyrrinate) complexes.

    Science.gov (United States)

    Bolotaulo, Duer; Metta-Magaña, Alejandro; Fortier, Skye

    2017-03-07

    Using an improved, chromatography-free dipyrrin synthesis, the α,β-unsubstituted dipyrrins [RC(C 4 H 2 N) 2 H] (2) (R = tolyl (2toly l ), p-OMe-C 6 H 4 (2anis), mesityl (2mes), ferrocenyl (2Fc)) were isolated in good to excellent yields. Deprotonation of 2 with Na[N(SiMe 3 ) 2 ] gives the alkali metal salts [Na(DME) n ][RC(C 4 H 2 N) 2 ] (3) which reacts with UO 2 Cl 2 (THF) 3 to give the uranyl bis(dipyrrinates) UO 2 [RC(C 4 H 2 N) 2 ] 2 (L) (L = THF (4R-THF); DMAP (4R-DMAP)) (R = tolyl, p-OMe-C 6 H 4 , mesityl, ferrocenyl). The THF adducts, 4R-THF, are unstable in aromatic and nonpolar solvents and rapidly decompose to 2 and an intractable uranium-containing solid. On the other hand, the DMAP adducts, 4R-DMAP, are indefinitely stable in solution. The solid-state structures of 4R-THF and 4R-DMAP reveal distorted trigonal bipyramidal geometries. In the solid-state, the dipyrrinate ligands exhibit significant distortions including bowing and, in some instances, out-of-plane equatorial N-atom coordination, likely as a consequence of steric crowding and interligand repulsion. The complexes, 4R-DMAP, have been fully characterized by NMR, UV/Vis, and fluorescence spectroscopies, and their electrochemical properties have been investigated through cyclic voltammetry. The cyclic voltammograms of 4R-DMAP display several redox features but present a reversible wave at ca. -1.9 V (vs. Fc 0/+ ) attributable to a ligand centred reduction. Fluorescence measurements of all compounds reveal that only the mesityl derivatives 2mes, 3mes, and 4mes fluoresce with modest Stokes shift that ranges from ca. 30-70 nm, with 4mes displaying the greatest relative emission intensity.

  10. Structural, Optical, Morphological and Elemental Analysis on Sol-gel Synthesis of Ni Doped TiO2 Nanocrystallites

    Directory of Open Access Journals (Sweden)

    T. Sakthivel

    2017-06-01

    Full Text Available Pure and Ni doped titanium dioxide nanoparticles were successfully synthesized by sol-gel method and characterized usingXRD, UV-Visible, FTIR, FESEM and EDS techniques. XRD pattern confirms the formation of tetragonal TiO2. The absorbance spectra of pure and Ni doped TiO2 showed absorption spectrum at ultra-violet region due to electronic transition between bonding and anti-bonding orbital (π-π•. Bandgap energy of Ni doped TiO2 decreased to 2.5 eV when compared to pure TiO2 (3.39 eV. FESEM study reveals agglomerated spherical shaped morphology. The functional groups of the prepared samples were identified using FTIR spectroscopy and the elemental analysis was further supported with EDS analysis.

  11. Synthesis and physicochemical investigation of complexes of rare earth, alkaline earth elements and copper with some β-diketones

    International Nuclear Information System (INIS)

    Nichiporuk, R.V.; Pechurova, N.I.; Snezhko, N.I.; Martynenko, L.I.; Kaul', A.R.; Zanina, A.S.; Shergina, S.I.; Sokolov, I.E.

    1991-01-01

    Complexes of rare earth, alkaline earth elements and copper with 2-methoxy-2,6,6-trimethylheptanedion-3,5 as well as complexes of yttrium and barium with 2-methoxy-2,6-dimethylheptanedion-3,5 were synthesized. Prepared complexes were investigated by the methods of chemical, thermal, X-ray phase analyses, IR spectroscopy. Complex sublimation was studied at 10 -1 -10 -2 mm Hg. Complexes of rare earths and copper don't change their composition during sublimation, and sublimation of hydrated complexes of barium, strontium and calcium leads to formation of anhydrous complexes. All prepared complexes are able to transsublimate multiply and qualitatively without change of composition. All isolated complexes can be used for preparation of film oxide coatings by CVD method

  12. Synthesis and evaluation of germanic organometallic compounds as precursors for chemical vapor deposition (CVD) and for obtaining nanoparticles of elemental germanium

    International Nuclear Information System (INIS)

    Ballestero Martinez, Ernesto

    2014-01-01

    The interest in the development of materials that have applications in areas such as electronics or biomarkers has affected the synthesis of new compounds based on germanium. This element has two states of common oxidation, +4 and +2, of them, the +2 oxidation state is the least studied and more reactive. Additionally, compounds of germanium (II) have similarities to carbenes in terms Lewis'acid base chemistry. The preparation of compounds of germanium (II) with ligands β-diketiminates has made possible the stabilization of new chemical functionalities and, simultaneously, it has provided interesting thermal properties to develop new methods of preparation of materials with novel properties. The preparation of amides germanium (II) L'Ge (NHPh) [1, L'= {HC (CMeN-2,4,6-Me 3 C 6 H 2 ) 2 } - ], L'Ge (4-NHPy) [2], L'Ge (2-NHPy) [3] and LGe(2-NHPy) [4, L = {HC (CMeN-2,6- i Pr 2 C 6 H 3 ) 2 ] - ] are presented, the chemical and structural composition was determined by using techniques such as nuclear magnetic resonance ( 1 H, 13 C), elemental analysis, melting point, infrared spectroscopy, X-ray diffraction of single crystal and thermogravimetric analysis (TGA). The TGA has demonstrated that 1-4 experience a thermal decomposition, therefore, these compounds could be considered as potential starting materials for the obtaining of germanium nitride (GeN x ). Certainly, the availability of coordinating nitrogen atoms in the chemical composition in 2-4 have been interesting given that it could act as ligands in reactions with transition metal complexes. Thus, relevant information to molecular level could be obtained for some reactions and interactions that have used similar link sites in surface chemistry, for example, the chemical functionalization of silicon and germanium substrate. Additionally, the synthesis and structural characterization of germanium chloride compound (II) L G eCl [5, L' = HC{(CMe) (N-2,6-Me 2 C 6 H 3 )} 2 - ] is reported

  13. Synthesis and evaluation of germanium organometallic compounds as precursors for chemical vapor deposition (CVD) and for obtaining nanoparticles of elemental germanium

    International Nuclear Information System (INIS)

    Ballestero Martinez, Ernesto

    2014-01-01

    The interest in the development of materials having applications such as electronics areas or biomarkers has affected the synthesis of new compounds based on germanium. This element has had two common oxidation states, +4 and +2, of them, +2 oxidation state has been the least studied and more reactive. Additionally, compounds of germanium (II) have had similarities with carbenes regarding the chemical acid-base Lewis. The preparation of compounds of germanium (II) with ligands β-decimations has enabled stabilization of new chemical functionalities and, simultaneously, provided interesting thermal properties to develop new preparation methodologies of materials with novel properties. The preparation of amides germanium(II) L'Ge(NHPh) [1, L' = {HC (CMeN-2,4,6-Me 3 C 6 H 2 ) 2 }], L'Ge(4-NHPy) [2] L'Ge(2-NHPy) [3] and LGe(2-NHPy) [4, L = {HC(CMeN-2,6- i Pr 2 C 6 H 3 ) 2 }]; the structural chemical composition were determined using techniques such as nuclear magnetic resonance ( 1 H, 13 C), other techniques are treated: elemental analysis, melting point, infrared spectroscopy, X-ray diffraction of single crystal and thermal gravimetric analysis (TGA). The TGA has showed that 4-1 have experimented a thermal decomposition; therefore, these compounds could be considered as potential starting materials for obtaining germanium nitride (GeN x ). Certainly, the availability of nitrogen coordinating atoms in the chemical composition in 2-4 have been interesting because it could act as ligands in reactions with transition metal complexes. That way, information could be obtained at the molecular level for some reactions and interactions that in surface chemistry have used similar link sites, for example, chemical functionalization of silicon and germanium substrates. The synthesis and structural characterization of germanium chloride compound(II) L''GeCl [5, L'' = HC{(CMe) (N-2,6-Me 2 C 6 H 3 )} 2 ], which could be used later for the

  14. Gas-Phase Synthesis of Bimetallic Oxide Nanoparticles with Designed Elemental Compositions for Controlling the Explosive Reactivity of Nanoenergetic Materials

    Directory of Open Access Journals (Sweden)

    Ji Young Ahn

    2011-01-01

    Full Text Available We demonstrate a simple and viable method for controlling the energy release rate and pressurization rate of nanoenergetic materials by controlling the relative elemental compositions of oxidizers. First, bimetallic oxide nanoparticles (NPs with a homogeneous distribution of two different oxidizer components (CuO and Fe2O3 were generated by a conventional spray pyrolysis method. Next, the Al NPs employed as a fuel were mixed with CuO-Fe2O3 bimetallic oxide NPs by an ultrasonication process in ethanol solution. Finally, after the removal of ethanol by a drying process, the NPs were converted into energetic materials (EMs. The effects of the mass fraction of CuO in the CuO-Fe2O3 bimetallic oxide NPs on the explosive reactivity of the resulting EMs were examined by using a differential scanning calorimeter and pressure cell tester (PCT systems. The results clearly indicate that the energy release rate and pressurization rate of EMs increased linearly as the mass fraction of CuO in the CuO-Fe2O3 bimetallic oxide NPs increased. This suggests that the precise control of the stoichiometric proportions of the strong oxidizer (CuO and mild oxidizer (Fe2O3 components in the bimetallic oxide NPs is a key factor in tuning the explosive reactivity of EMs.

  15. Synthesis and elastic properties of V2AlC thin films by magnetron sputtering from elemental targets

    International Nuclear Information System (INIS)

    Sigumonrong, Darwin P; Music, Denis; Schneider, Jochen M; Zhang Jie; Zhou Yanchun

    2009-01-01

    The influence of deposition temperature on phase formation of V 2 AlC is studied by magnetron sputtering from elemental targets. At substrate temperatures below 750 0 C, we observed the formation of Al x V y and V 2 C using x-ray diffraction (XRD) analysis. At 750 0 C, a phase pure polycrystalline V 2 AlC film on a ∼12 nm thick transition layer has been observed using XRD and transmission electron microscopy. Selected area electron diffraction indicates that the film grown on the transition layer consists of phase pure V 2 AlC. As the substrate temperature is increased to 850 0 C, the formation of V 2 C in addition to the V 2 AlC phase is observed. This may be due to desorption of aluminium causing the decomposition of V 2 AlC into vanadium carbides and aluminium. The V 2 AlC film is fully dense and polycrystalline and the elastic modulus based on nanoindentation is within the expected error margin consistent with previously reported theoretical calculations and the diamond anvil cell measurement of bulk V 2 AlC samples.

  16. Synthesis and elastic properties of V{sub 2}AlC thin films by magnetron sputtering from elemental targets

    Energy Technology Data Exchange (ETDEWEB)

    Sigumonrong, Darwin P; Music, Denis; Schneider, Jochen M [Materials Chemistry, RWTH Aachen University, Mies-van-der-Rohe-Str. 10, 52074 Aachen (Germany); Zhang Jie; Zhou Yanchun [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

    2009-09-21

    The influence of deposition temperature on phase formation of V{sub 2}AlC is studied by magnetron sputtering from elemental targets. At substrate temperatures below 750 {sup 0}C, we observed the formation of Al{sub x}V{sub y} and V{sub 2}C using x-ray diffraction (XRD) analysis. At 750 {sup 0}C, a phase pure polycrystalline V{sub 2}AlC film on a {approx}12 nm thick transition layer has been observed using XRD and transmission electron microscopy. Selected area electron diffraction indicates that the film grown on the transition layer consists of phase pure V{sub 2}AlC. As the substrate temperature is increased to 850 {sup 0}C, the formation of V{sub 2}C in addition to the V{sub 2}AlC phase is observed. This may be due to desorption of aluminium causing the decomposition of V{sub 2}AlC into vanadium carbides and aluminium. The V{sub 2}AlC film is fully dense and polycrystalline and the elastic modulus based on nanoindentation is within the expected error margin consistent with previously reported theoretical calculations and the diamond anvil cell measurement of bulk V{sub 2}AlC samples.

  17. Sodium Phenylbutyrate Enhances Astrocytic Neurotrophin Synthesis via Protein Kinase C (PKC)-mediated Activation of cAMP-response Element-binding Protein (CREB)

    Science.gov (United States)

    Corbett, Grant T.; Roy, Avik; Pahan, Kalipada

    2013-01-01

    Neurotrophins, such as brain-derived neurotrophic factor (BDNF) and neurotrophin-3 (NT-3), are believed to be genuine molecular mediators of neuronal growth and homeostatic synapse activity. However, levels of these neurotrophic factors decrease in different brain regions of patients with Alzheimer disease (AD). Induction of astrocytic neurotrophin synthesis is a poorly understood phenomenon but represents a plausible therapeutic target because neuronal neurotrophin production is aberrant in AD and other neurodegenerative diseases. Here, we delineate that sodium phenylbutyrate (NaPB), a Food and Drug Administration-approved oral medication for hyperammonemia, induces astrocytic BDNF and NT-3 expression via the protein kinase C (PKC)-cAMP-response element-binding protein (CREB) pathway. NaPB treatment increased the direct association between PKC and CREB followed by phosphorylation of CREB (Ser133) and induction of DNA binding and transcriptional activation of CREB. Up-regulation of markers for synaptic function and plasticity in cultured hippocampal neurons by NaPB-treated astroglial supernatants and its abrogation by anti-TrkB blocking antibody suggest that NaPB-induced astroglial neurotrophins are functionally active. Moreover, oral administration of NaPB increased the levels of BDNF and NT-3 in the CNS and improved spatial learning and memory in a mouse model of AD. Our results highlight a novel neurotrophic property of NaPB that may be used to augment neurotrophins in the CNS and improve synaptic function in disease states such as AD. PMID:23404502

  18. Synthesis and properties of bis(pentamethylcyclopentadienyl) actinide hydrocarbyls and hydrides. A new class of highly reactive f-element organometallic compounds

    International Nuclear Information System (INIS)

    Fagan, P.J.; Manriquez, J.M.; Maatta, E.A.; Seyam, A.M.; Marks, T.J.

    1981-01-01

    The synthesis and chemical and physcochemical properties of Th and U bis(pentamethylcyclopentadienyl) chlorides, hydrocarbyls, chlorohydrocarbyls, and hydrides are reported. The reaction of the precursor compounds M[eta 5 -(CH 3 ) 5 C 5 ] 2 Cl 2 with 2 equiv of lithium reagent RLi produces M[eta 5 -(CH 3 ) 5 ] 2 R 2 compounds where R = CH 3 , CH 2 Si(CH 3 ) 3 , CH 2 C(CH 3 ) 3 , CH 2 C 6 H 5 , and C 6 H 5 (M = Th) and R = CH 3 , CH 2 Si(CH 3 ) 3 , CH 2 C 6 H 5 , and C 6 H 5 (M = U) in good yield. With 1 equiv of lithium reagent, M[eta 5 -(CH 3 ) 5 C 5 ] 2 (R)Cl compounds where R = CH 2 C(CH 3 ) 3 , CH 2 Si(CH 3 ) 3 , CH 2 C 6 H 5 , and C 6 H 5 (M = Th) and R = CH 2 C(CH 3 ) 3 CH 2 Si(C 3 ) 3 , CH 2 C 6 H 5 , and C 6 H 5 , and C 6 H 5 (M = U) are formed in high yield. The M[eta 5 -(CH 3 ) 5 C 52 (C 3 )Cl compounds can be synthesized by redistribution between the corresponding dimethyl and dichloro complexes. The new organoactinides were thoroughly characterized by elemental analysis, 1 H NMR and vibrational spectroscopy, and in many cases cryoscopic molecular weight measurements. The hydrocarbyls and chlorohydrocarbyls generally exhibit high thermal stability. However, the diphenyl compounds react readily with C 6 D 6 to yield, via a benzyne complex, the corresponding M(C 6 D 5 ) 2 compounds. The Th bis(neopentyl) complex reacts with benzene to produce the corresponding diphenyl complex. Competition experiments at -78 0 C indicate that the Th complexes are more reactive than those of U. The M[eta 5 -(CH 3 ) 5

  19. Synthesis and properties of layered synthetic microstructure (LSM) dispersion elements for 62 eV (200A) to 1.24 keV (10A) radiation. Final report

    International Nuclear Information System (INIS)

    Barbee, T.W. Jr.

    1981-08-01

    The opportunities offered by engineered synthetic multilayer dispersion elements for x-rays have been recognized since the earliest days of x-ray diffraction analysis. In this paper, application of sputter deposition technology to the synthesis of Layered Synthetic Microstructure (LSMs) of sufficient quality for use as x-ray dispersion elements is discussed. It will be shown that high efficiency, controllable bandwidth dispersion elements, with d spacings varying from 15 A to 180 A, may be synthesized onto both mechanically stiff and flexible substrates. Multilayer component materials include tungsten, niobium, molybdenum, titanium, vanadium, and silicon layers separated by carbon layers. Experimental observations of peak reflectivity in first order, integrated reflectivity in first order, and diffraction performance at selected photon energies in the range, 100 to 15,000 eV, are reported and compared to theory

  20. Elements beyond uranium

    International Nuclear Information System (INIS)

    Seaborg, G.T.; Loveland, W.D.

    1990-01-01

    This book is the 12th volume in a series on transuranium elements. Varied techniques for production of these elements, the methods used in the identification, and the exquisitely refined microchemical techniques required to deal wth samples sometimes involving only a few atoms are described in detail. The chapter on synthesis of the new elements is liberally laced with reminiscences of the proud progenitors as well as the criteria for the discovery of a new chemical element. The authors lament that the superheavy elements (elements in the region of atomic number 114) still elude detection even though their creation should be possible, and some, at least, should survive long enough to be detected. One chapter in the book is devoted to practical applictions of uranium, and the transuranic elements

  1. Engineering Synthesis of Nonlinear Spatial Selection with Artificial Intelligence Elements to Suppress Critical Interference of Background in Aviation and Space-Based Opto-Electronic Devices

    Directory of Open Access Journals (Sweden)

    V. L. Levshin

    2015-01-01

    Full Text Available The previous authors’ works have shown that the system of quasi-optimal linear spatial filtering, due to the restriction of this class of filters, related to the superposition principle, has very limited capacity to suppress the most critical interference spatially inhomogeneous background. Such partial suppression does not meet extreme approach requirements for providing high probability characteristics to detect small targets in the most difficult background conditions.In this regard, there is a conclusion that it is necessary to find a different approach, in which the result of the system operation in complex background does not depend on the level of the background noise at the input. This article performs an engineering synthesis of the system with the artificial visual intelligence elements, which recognizes a class of the small-sized radiating objects with the suppression of the most critical interference through nonlinear topological selection.Consideration of this problem begins with the formation of the filter-discriminator aperture, which is a basis for this theory, «echoing» with the theory of optimal nonlinear filtering spatial Poisson processes. Thus, formation of the optimized nonlinear filter structure is based on the optimal linear filter (Wiener filter structure. As a result, there are three versions of filter apertures (4-, 8- and 16-connected ones, with one of which later providing operations of the object shape discrimination. The focus of the article is, mainly, on the 8-connected aperture, as the average in balance of efficiency and complexity option.The article pays considerable attention to development of signs and algorithms to select the objects by size and shape. It shows that selection on a uniform background is possible by the maximum value of the first derivative and to separate the most critical form of Markov’s field inhomogeneities and background brightness, as the fragments of component boundaries of

  2. The transuranium elements: From neptunium and plutonium to element 112

    International Nuclear Information System (INIS)

    Hoffman, D.C.

    1996-01-01

    Beginning in the 1930's, both chemists and physicists became interested in synthesizing new artificial elements. The first transuranium element, Np, was synthesized in 1940. Over the past six decades, 20 transuranium elements have been produced. A review of the synthesis is given. The procedure of naming the heavy elements is also discussed. It appears feasible to produce elements 113 and 114. With the Berkeley Gas-filled Separator, it should be possible to reach the superheavy elements in the region of the spherical Z=114 shell, but with fewer neutrons than the N=184 spherical shell. 57 refs, 6 figs

  3. The use of ion beam analysis in the synthesis of materials. A review of the determination of light elements by high-energy resonant backscattering

    International Nuclear Information System (INIS)

    Nastasi, M.

    1999-01-01

    For the ion synthesis of materials plasma inversion ion processing (PIIP) technology, has been applied in the framework of materials science research. The characteristics of this technique are discussed. PIIP has been complemented and compared with alpha-particle Rutherford Backscattering Spectrometry (RBS) High-energy Backscattering Spectrometry (HEBS) is the third material testing method for comparison. Examples for each technology are presented and discussed. (R.P.)

  4. Free Vibration Analysis of a Spinning Flexible DISK-SPINDLE System Supported by Ball Bearing and Flexible Shaft Using the Finite Element Method and Substructure Synthesis

    Science.gov (United States)

    JANG, G. H.; LEE, S. H.; JUNG, M. S.

    2002-03-01

    Free vibration of a spinning flexible disk-spindle system supported by ball bearing and flexible shaft is analyzed by using Hamilton's principle, FEM and substructure synthesis. The spinning disk is described by using the Kirchhoff plate theory and von Karman non-linear strain. The rotating spindle and stationary shaft are modelled by Rayleigh beam and Euler beam respectively. Using Hamilton's principle and including the rigid body translation and tilting motion, partial differential equations of motion of the spinning flexible disk and spindle are derived consistently to satisfy the geometric compatibility in the internal boundary between substructures. FEM is used to discretize the derived governing equations, and substructure synthesis is introduced to assemble each component of the disk-spindle-bearing-shaft system. The developed method is applied to the spindle system of a computer hard disk drive with three disks, and modal testing is performed to verify the simulation results. The simulation result agrees very well with the experimental one. This research investigates critical design parameters in an HDD spindle system, i.e., the non-linearity of a spinning disk and the flexibility and boundary condition of a stationary shaft, to predict the free vibration characteristics accurately. The proposed method may be effectively applied to predict the vibration characteristics of a spinning flexible disk-spindle system supported by ball bearing and flexible shaft in the various forms of computer storage device, i.e., FDD, CD, HDD and DVD.

  5. New functionalities in abundant element oxides: ubiquitous element strategy

    International Nuclear Information System (INIS)

    Hosono, Hideo; Hayashi, Katsuro; Kamiya, Toshio; Atou, Toshiyuki; Susaki, Tomofumi

    2011-01-01

    While most ceramics are composed of ubiquitous elements (the ten most abundant elements within the Earth's crust), many advanced materials are based on rare elements. A 'rare-element crisis' is approaching owing to the imbalance between the limited supply of rare elements and the increasing demand. Therefore, we propose a 'ubiquitous element strategy' for materials research, which aims to apply abundant elements in a variety of innovative applications. Creation of innovative oxide materials and devices based on conventional ceramics is one specific challenge. This review describes the concept of ubiquitous element strategy and gives some highlights of our recent research on the synthesis of electronic, thermionic and structural materials using ubiquitous elements. (topical review)

  6. Synthesis, characterization, and wear and friction properties of variably structured SiC/Si elements made from wood by molten Si impregnation

    DEFF Research Database (Denmark)

    Dhiman, Rajnish; Rana, Kuldeep; Bengu, Erman

    2012-01-01

    We have synthesized pre-shaped SiC/Si ceramic material elements from charcoal (obtained from wood) by impregnation with molten silicon, which takes place in a two-stage process. In the first process, a porous structure of connected micro-crystals of β-SiC is formed, while, in the second process...

  7. Standard elements; Elements standards

    Energy Technology Data Exchange (ETDEWEB)

    Blanc, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Following his own experience the author recalls the various advantages, especially in the laboratory, of having pre-fabricated vacuum-line components at his disposal. (author) [French] A la suite de sa propre experience, l'auteur veut rappeler les divers avantages que presente, tout particulierement en laboratoire, le fait d'avoir a sa disposition des elements pre-fabriques de canalisations a vide. (auteur)

  8. Chemistry of superheavy elements

    International Nuclear Information System (INIS)

    Schaedel, M.

    2012-01-01

    The chemistry of superheavy elements - or transactinides from their position in the Periodic Table - is summarized. After giving an overview over historical developments, nuclear aspects about synthesis of neutron-rich isotopes of these elements, produced in hot-fusion reactions, and their nuclear decay properties are briefly mentioned. Specific requirements to cope with the one-atom-at-a-time situation in automated chemical separations and recent developments in aqueous-phase and gas-phase chemistry are presented. Exciting, current developments, first applications, and future prospects of chemical separations behind physical recoil separators ('pre-separator') are discussed in detail. The status of our current knowledge about the chemistry of rutherfordium (Rf, element 104), dubnium (Db, element 105), seaborgium (Sg, element 106), bohrium (Bh, element 107), hassium (Hs, element 108), copernicium (Cn, element 112), and element 114 is discussed from an experimental point of view. Recent results are emphasized and compared with empirical extrapolations and with fully-relativistic theoretical calculations, especially also under the aspect of the architecture of the Periodic Table. (orig.)

  9. Synthesis imaging in radio astronomy

    International Nuclear Information System (INIS)

    Perley, R.A.; Schwab, F.R.; Bridle, A.H.

    1989-01-01

    Recent advances in techniques and instrumentation for radio synthesis imaging in astronomy are discussed in a collection of review essays. Topics addressed include coherence in radio astronomy, the interferometer in practice, primary antenna elements, cross correlators, calibration and editing, sensitivity, deconvolution, self-calibration, error recognition, and image analysis. Consideration is given to wide-field imaging (bandwidth and time-average smearing, noncoplanar arrays, and mosaicking), high-dynamic-range imaging, spectral-line imaging, VLBI, solar imaging with a synthesis telescope, synthesis imaging of spatially coherent objects, noise in images of very bright sources, synthesis observing strategies, and the design of aperture-synthesis arrays

  10. Synthesis of Y2O3: Eu added the group 1 or 2 elements using complex-polymerization and its luminescent properties

    International Nuclear Information System (INIS)

    Park, Sang Mi; Jang, Ho G.; Kim, Chang Hae; Park, Joung Kyu; Park, Hee Dong

    2001-01-01

    Europium activated yttrium oxide (Y 2 O 3 :Eu) is extensively applied to red phosphor for Flat Panel Display because of its high efficiency and the thermal and chemical stability. Flat Panel Display screen which have a high resolution and high efficiency needs to the phosphors of ideally small size spherical particle. In this study, we prepared a Y 2 O 3 :Eu phosphor using polymeric precursor methods and investigated the codoping effect by introducing the group 1 or 2 elements to Y 2 O 3 :Eu phosphor in view of improvement of luminance efficiency

  11. Studies on synthesis of a kind of new colour reagents bromophosphonobisazo derivatives of chromotropic acid and the effect of their constitution on colour behaviours with rare earth elements

    International Nuclear Information System (INIS)

    Bincai, W.; Yuxin, Q.; Hengchuan, L.

    1985-01-01

    Based on the previous systematic studies, this paper reports to the original constitution of chlorophosphonazo type of colour reagents, has been reformed, and a kind of 14 new asymmetrical bromophosphonobisazo colour reagents of chromotropic acid have been designed and synthesized. In the meanwhile, the relationship between constitution of colour reagents and its behaviour in colour reaction with rare earth elements has been investigated. In addition, the general colour behaviours of these reagents and the influence of organic solvents and surfactants have been preliminarily studied

  12. Proceedings of transuranium elements

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The identification of the first synthetic elements was established by chemical evidence. Conclusive proof of the synthesis of the first artificial element, technetium, was published in 1937 by Perrier and Segre. An essential aspect of their achievement was the prediction of the chemical properties of element 43, which had been missing from the periodic table and which was expected to have properties similar to those of manganese and rhenium. The discovery of other artificial elements, astatine and francium, was facilitated in 1939-1940 by the prediction of their chemical properties. A little more than 50 years ago, in the spring of 1940, Edwin McMillan and Philip Abelson synthesized element 93, neptunium, and confirmed its uniqueness by chemical means. On August 30, 1940, Glenn Seaborg, Arthur Wahl, and the late Joseph Kennedy began their neutron irradiations of uranium nitrate hexahydrate. A few months later they synthesized element 94, later named plutonium, by observing the alpha particles emitted from uranium oxide targets that had been bombarded with deuterons. Shortly thereafter they proved that is was the second transuranium element by establishing its unique oxidation-reduction behavior. The symposium honored the scientists and engineers whose vision and dedication led to the discovery of the transuranium elements and to the understanding of the influence of 5f electrons on their electronic structure and bonding. This volume represents a record of papers presented at the symposium

  13. Galvanic element. Galvanisches Element

    Energy Technology Data Exchange (ETDEWEB)

    Sprengel, D.; Haelbig, H.

    1980-01-03

    The invention concerns a gas-tight sealed accumulator with positive and negative electrode plates and an auxillary electrode electroconductively bound to the latter for suppressing oxygen pressure. The auxillary electrode is an intermediate film electrode. The film catalysing oxygen reduction is hydrophilic in character and the other film is hydrophobic. A double coated foil has proved to be advantageous, the hydrophilic film being formed from polymer-bound activated carbon and the hydrophrobic film from porous polytetrafluoroethylene. A metallic network of silver or nickel is rolled into the outer side of the activated carbon film. This auxillary electrode can be used to advantage in all galvanic elements. Even primary cells fall within the scope of application for auxillary electrodes because many of these contain a highly oxidized electrodic material which tends to give off oxygen.

  14. Steering committee for the management of the post-accidental phase of a nuclear accident or of a radiological situation (CODIRPA). Work group nr 4. Response to health challenges after a radiological accident - Stage report issue nr 2 of 2007 November 5; Synthesis of doctrinal elements and recommendations; Consultative meeting - February 2009; Final report March 2011; Report synthesis

    International Nuclear Information System (INIS)

    Bernier, Marie-Odile; Challeton-de Vathaire, Cecile; Catelinois, Olivier; Pirard, Philippe; Collignon, Albert; Corblet, Sibylle; Empereur Bissonnet, Pascal; Fite, Johanna; Mehl Auget, Isabelle; Fleutot, Jean-Baptiste; Gavel, Yves; Geis-Bonnemains, Nathalie; Geneau, Christian; Guagniere, Bertrand; Janin, Claire; Lang, Thierry; Marielle, Schmitt; N'Diaye, Bakhao; Raoul, Christophe; Ricoux, Christine; Schwoebel, Valerie; Telion, Caroline; Tillier, Claude; Verger, Pierre; Volant, Philippe

    2007-01-01

    A first report describes effects of radiological accidents on health, and possible scenarios (dose assessments, exposed population, health challenges), gives an overview of methods and arrangements used to count exposed populations and to assess received doses, and presents the foreseen reception centres. It describes the health management organisation (medical and psychological care of exposed population, public information), and reports an analysis of health risks associated with the accident. The next document contains a synthesis of doctrinal elements and recommendations regarding information acquisition, the management of health consequences of the accident, the assessment of the health impact. Propositions made by the work group to face health challenges are presented in a Power Point presentation. The final report addresses the context of preparation of the response to a radiological accident in France (studied accidents and scenarios, public health challenges), proposes a chronological synthesis of actions to be undertaken during a preparation phase, an emergency phase, a transition phase, and a long term phase), and a detailed presentation of main actions to be undertaken (medical and psychological care, reception centres, counting, health risk analysis, health information)

  15. Sodium phenylbutyrate enhances astrocytic neurotrophin synthesis via protein kinase C (PKC)-mediated activation of cAMP-response element-binding protein (CREB): implications for Alzheimer disease therapy.

    Science.gov (United States)

    Corbett, Grant T; Roy, Avik; Pahan, Kalipada

    2013-03-22

    Neurotrophins, such as brain-derived neurotrophic factor (BDNF) and neurotrophin-3 (NT-3), are believed to be genuine molecular mediators of neuronal growth and homeostatic synapse activity. However, levels of these neurotrophic factors decrease in different brain regions of patients with Alzheimer disease (AD). Induction of astrocytic neurotrophin synthesis is a poorly understood phenomenon but represents a plausible therapeutic target because neuronal neurotrophin production is aberrant in AD and other neurodegenerative diseases. Here, we delineate that sodium phenylbutyrate (NaPB), a Food and Drug Administration-approved oral medication for hyperammonemia, induces astrocytic BDNF and NT-3 expression via the protein kinase C (PKC)-cAMP-response element-binding protein (CREB) pathway. NaPB treatment increased the direct association between PKC and CREB followed by phosphorylation of CREB (Ser(133)) and induction of DNA binding and transcriptional activation of CREB. Up-regulation of markers for synaptic function and plasticity in cultured hippocampal neurons by NaPB-treated astroglial supernatants and its abrogation by anti-TrkB blocking antibody suggest that NaPB-induced astroglial neurotrophins are functionally active. Moreover, oral administration of NaPB increased the levels of BDNF and NT-3 in the CNS and improved spatial learning and memory in a mouse model of AD. Our results highlight a novel neurotrophic property of NaPB that may be used to augment neurotrophins in the CNS and improve synaptic function in disease states such as AD.

  16. Synthesis and characterization of f-element iodate architectures with variable dimensionality, alpha- and beta-Am(IO3)3.

    Science.gov (United States)

    Runde, Wolfgang; Bean, Amanda C; Brodnax, Lia F; Scott, Brian L

    2006-03-20

    Two americium(III) iodates, beta-Am(IO3)3 (I) and alpha-Am(IO3)3 (II), have been prepared from the aqueous reactions of Am(III) with KIO(4) at 180 degrees C and have been characterized by single-crystal X-ray diffraction, diffuse reflectance, and Raman spectroscopy. The alpha-form is consistent with the known structure type I of anhydrous lanthanide iodates. It consists of a three-dimensional network of pyramidal iodate groups bridging [AmO8] polyhedra where each of the americium ions are coordinated to eight iodate ligands. The beta-form reveals a novel architecture that is unknown within the f-element iodate series. beta-Am(IO3)3 exhibits a two-dimensional layered structure with nine-coordinate Am(III) atoms. Three crystallographically unique pyramidal iodate anions link the Am atoms into corrugated sheets that interact with one another through intermolecular IO3-...IO3- interactions forming dimeric I2O10 units. One of these anions utilizes all three O atoms to simultaneously bridge three Am atoms. The other two iodate ligands bridge only two Am atoms and have one terminal O atom. In contrast to alpha-Am(IO3)3, where the [IO3] ligands are solely corner-sharing with [AmO8] polyhedra, a complex arrangement of corner- and edge-sharing mu2- and mu3-[IO3] pyramids can be found in beta-Am(IO3)3. Crystallographic data: I, monoclinic, space group P2(1)/n, a = 8.871(3) A, b = 5.933(2) A, c = 15.315(4) A, beta = 96.948(4) degrees , V = 800.1(4) A(3), Z = 4; II, monoclinic, space group P2(1)/c, a = 7.243(2) A, b = 8.538(3) A, c = 13.513(5) A, beta = 100.123(6) degrees , V = 822.7(5) A(3), Z = 4.

  17. Mendeleev's principle against Einstein's relativity: news from the chemistry of superheavy elements

    Energy Technology Data Exchange (ETDEWEB)

    Gaeggeler, Heinz W [Department of Chemistry and Biochemistry, University of Bern, Bern (Switzerland)

    2009-12-31

    The review briefly considers the problems of synthesis and chemical identification of superheavy elements. The specific features of their properties are determined by the relativistic effects. The synthesis and chemical investigations into bohrium and element 112 are discussed as examples.

  18. Transplutonium elements

    Energy Technology Data Exchange (ETDEWEB)

    Sivaramakrishnan, C. K.; Jadhav, A. V.; Reghuraman, K.; Mathew, K. A.; Nair, P. S.; Ramaniah, M. V.

    1973-07-01

    Research progress is reported on studies of the transplutonium elements including recovery and purification of americium, preparation of /sup 238/Pu, extraction studies using diethylhexyl phosphate. (DHM)

  19. Toxic Elements

    DEFF Research Database (Denmark)

    Hajeb, Parvaneh; Shakibazadeh, Shahram; Sloth, Jens Jørgen

    2016-01-01

    Food is considered the main source of toxic element (arsenic, cadmium, lead, and mercury) exposure to humans, and they can cause major public health effects. In this chapter, we discuss the most important sources for toxic element in food and the foodstuffs which are significant contributors to h...

  20. Fuel element

    International Nuclear Information System (INIS)

    Armijo, J.S.

    1976-01-01

    A fuel element for nuclear reactors is proposed which has a higher corrosion resisting quality in reactor operations. The zirconium alloy coating around the fuel element (uranium or plutonium compound) has on its inside a protection layer of metal which is metallurgically bound to the substance of the coating. As materials are namned: Alluminium, copper, niobium, stainless steel, and iron. This protective metallic layer has another inner layer, also metallurgically bound to its surface, which consists usually of a zirconium alloy. (UWI) [de

  1. PELTIER ELEMENTS

    CERN Document Server

    Tani, Laurits

    2015-01-01

    To control Peltier elements, temperature controller was used. I used TEC-1091 that was manufactured my Meerstetter Engineering. To gain control with the temperature controller, software had to be intalled on a controlling PC. There were different modes to control the Peltier: Tempererature controller to control temperature, Static current/voltage to control voltage and current and LIVE ON/OFF to auto-tune the controller respectively to the system. Also, since near the collision pipe there is much radiation, radiation-proof Peltier elements have to be used. To gain the best results, I had to find the most efficient Peltier elements and try to get their cold side to -40 degrees Celsius.

  2. Heavy ion deep inelastic collisions studied by discrete gamma ray spectroscopy

    International Nuclear Information System (INIS)

    Krolas, W.

    1996-05-01

    The discrete gamma ray spectroscopy has been used as a tool to investigate the heavy ion collision. It has been shown that such experimental information supplemented by results of additional of-line radioactivity measurements is complete enough to reconstruct distributions of products of very complex nuclear reactions. Three experiments have been performed in which the 208 Pb + 64 Ni, 130 Te + 64 Ni and 208 Pb + 58 Ni systems have been created. The production cross sections of fragment isotopes have been determined and compared with existing model predictions

  3. Synthesis through Trans-disciplinarity

    DEFF Research Database (Denmark)

    Hansen, Hanne Tine Ring

    2006-01-01

    synthesis is a requirement for creating successful ‘environmentally sustainable' architecture through the application of trans-disciplinarity, which leads to an increased awareness of the differences in decision-making as well as that of communication barriers between the different professions......When looking up the word ‘synthesis' in a dictionary, one comes across the following definition: "The combining of separate elements or substances to form a coherent whole."[1] Based on this definition one could argue that all great architectureis achieved through synthesis in one way or another...

  4. Organic chemistry of elemental phosphorus

    International Nuclear Information System (INIS)

    Milyukov, V A; Budnikova, Yulia H; Sinyashin, Oleg G

    2005-01-01

    The principal achievements and the modern trends in the development of the chemistry of elemental phosphorus are analysed, described systematically and generalised. The possibilities and advantages of the preparation of organophosphorus compounds directly from white phosphorus are demonstrated. Attention is focused on the activation and transformation of elemental phosphorus in the coordination sphere of transition metal complexes. The mechanisms of the reactions of white phosphorus with nucleophilic and electrophilic reagents are discussed. Electrochemical approaches to the synthesis of organic phosphorus derivatives based on white phosphorus are considered.

  5. Superheavy elements in D I Mendeleev's Periodic Table

    Energy Technology Data Exchange (ETDEWEB)

    Oganessian, Yury Ts; Dmitriev, Sergey N [Flerov Laboratory for Nuclear Reactions, Joint Institute for Nuclear Research, Dubna, Moscow Region (Russian Federation)

    2009-12-31

    The results on the synthesis of new superheavy elements, synthesized in complete fusion reactions of {sup 48}Ca ions with actinide targets, are summarized and analyzed. The perspectives for the synthesis of element 117, as well as of elements with Z>=118 are also considered.

  6. Synthesis and Characterization of Colloidal Metal and Photovoltaic Semiconductor Nanocrystals

    KAUST Repository

    Abulikemu, Mutalifu

    2014-01-01

    -performing photovoltaic nanocrystals contain toxic elements, such as Pb, or scarce elements, such as In; thus, the production of solution-processable nanocrystals from earth-abundant materials using environmentally benign synthesis and processing methods has become a

  7. Chemical experiments with superheavy elements.

    Science.gov (United States)

    Türler, Andreas

    2010-01-01

    Unnoticed by many chemists, the Periodic Table of the Elements has been extended significantly in the last couple of years and the 7th period has very recently been completed with eka-Rn (element 118) currently being the heaviest element whose synthesis has been reported. These 'superheavy' elements (also called transactinides with atomic number > or = 104 (Rf)) have been artificially synthesized in fusion reactions at accelerators in minute quantities of a few single atoms. In addition, all isotopes of the transactinide elements are radioactive and decay with rather short half-lives. Nevertheless, it has been possible in some cases to investigate experimentally chemical properties of transactinide elements and even synthesize simple compounds. The experimental investigation of superheavy elements is especially intriguing, since theoretical calculations predict significant deviations from periodic trends due to the influence of strong relativistic effects. In this contribution first experiments with hassium (Hs, atomic number 108), copernicium (Cn, atomic number 112) and element 114 (eka-Pb) are reviewed.

  8. Fuel element

    International Nuclear Information System (INIS)

    Kennedy, S.T.

    1982-01-01

    A nuclear reactor fuel element wherein a stack of nuclear fuel is prevented from displacement within its sheath by a retainer comprising a tube member which is radially expanded into frictional contact with the sheath by means of a captive ball within a tapered bore. (author)

  9. New elements

    International Nuclear Information System (INIS)

    Flerov, G.

    1976-01-01

    The history is briefly described of the investigation of superheavy elements at the Joint Institute for Nuclear Research at Dubna. The significance of the investigation is assessed from the point of view of the nuclear structure study and major problems encountered in experimental efforts are indicated. Current experimental methods aiming at the discovery or the production of superheavy nuclei with Z approximately 114 are listed. (I.W.)

  10. Stability analysis of artificial synthetic overweight elements

    International Nuclear Information System (INIS)

    Zhou Jian

    1990-01-01

    Stability of artificial synthetic overweight elements has been analysed theoretically using a diagram of nuclear stability. It is indicated that overweight nucleus can be synthesized only when a certain amount of neutrons participate simultaneously in the synthesis. The maximum number of protons in overweight elements is 1002. The proton number of 'extreme overweight' elements of which the neutron star is possibly composed is in the range from 326 to 1002. It is expected that the mass number of the stable overweight elements with proton number 114 is in the range from 299 to 315

  11. Organic synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, S.E.

    1991-01-01

    This paper reports on reactions of organoboranes. Organoboron routes to unsaturated hydrocarbons. Boronic ester homologation. Properties of organosilicon compounds. Alkene synthesis (Peterson olefination). Allylsilanes and acylsilanes.

  12. Radiographic element

    International Nuclear Information System (INIS)

    Abbott, T.I.; Jones, C.G.

    1984-01-01

    Radiographic elements are disclosed comprised of first and second silver halide emulsion layers separated by an interposed support capable of transmitting radiation to which the second image portion is responsive. At least the first imaging portion contains a silver halide emulsion in which thin tubular silver halide grains of intermediate aspect ratios (from 5:1 to 8:1) are present. Spectral sensitizing dye is adsorbed to the surface of the tubular grains. Increased photographic speeds can be realized at comparable levels of crossover. (author)

  13. Superheavy elements

    CERN Document Server

    Hofmann, S

    1999-01-01

    The outstanding aim of experimental investigations of heavy nuclei is the exploration of spherical 'SuperHeavy Elements' (SHEs). On the basis of the nuclear shell model, the next double magic shell-closure beyond sup 2 sup 0 sup 8 Pb is predicted at proton numbers between Z=114 and 126 and at neutron number N=184. All experimental efforts aiming at identifying SHEs (Z>=114) were negative so far. A highly sensitive search experiment was performed in November-December 1995 at SHIP. The isotope sup 2 sup 9 sup 0 116 produced by 'radiative capture' was searched for in the course of a 33 days irradiation of a sup 2 sup 0 sup 8 Pb target with sup 8 sup 2 Se projectiles, however, only cross-section limits were measured. Positive results were obtained in experiments searching for elements from 110 to 112 using cold fusion and the 1n evaporation channel. The produced isotopes were unambiguously identified by means of alpha-alpha correlations. Not fission, but alpha emission is the dominant decay mode. The measurement ...

  14. State-of-the-art coordination chemistry of radioactive elements

    International Nuclear Information System (INIS)

    Kharisov, B I; Mendez-Rojas, Miguel A

    2001-01-01

    Modern procedures for the synthesis of coordination and organometallic compounds of actinides and technetium and the properties of these compounds are surveyed. Experimental techniques, including methods for the synthesis of actinide and technetium complexes from elemental metals (oxidative dissolution and direct electrosynthesis), salts and halide, carbonyl and other complexes are generalised. The bibliography includes 283 references.

  15. Fuel element

    International Nuclear Information System (INIS)

    Hirose, Yasuo.

    1982-01-01

    Purpose: To increase the plenum space in a fuel element used for a liquid metal cooled reactor. Constitution: A fuel pellet is secured at one end with an end plug and at the other with a coil spring in a tubular container. A mechanism for fixing the coil spring composed of a tubular unit is mounted by friction with the inner surface of the tubular container. Accordingly, the recoiling force of the coil spring can be retained by fixing mechanism with a small volume, and since a large amount of plenum space can be obtained, the internal pressure rise in the cladding tube can be suppressed even if large quantities of fission products are discharged. (Kamimura, M.)

  16. On the Necessity of Using Element No.155 in the Chemical Physical Calculations: Again on the Upper Limit in the Periodic Table of Elements

    Directory of Open Access Journals (Sweden)

    Khazan A.

    2010-10-01

    Full Text Available It is shown how the properties of different elements of the Periodic System of Elements can be obtained using the properties of the theoretically predicted heaviest element No.155 (it draws the upper principal limit of the Table, behind which stable elements cannot exist. It is suggested how the properties of element No.155 can be used in the synthesis of superheavy elements. An analysis of nuclear reactions is also produced on the same basis.

  17. Synthesis of quantum dots

    Science.gov (United States)

    McDaniel, Hunter

    2017-10-17

    Common approaches to synthesizing alloyed quantum dots employ high-cost, air-sensitive phosphine complexes as the selenium precursor. Disclosed quantum dot synthesis embodiments avoid these hazardous and air-sensitive selenium precursors. Certain embodiments utilize a combination comprising a thiol and an amine that together reduce and complex the elemental selenium to form a highly reactive selenium precursor at room temperature. The same combination of thiol and amine acts as the reaction solvent, stabilizing ligand, and sulfur source in the synthesis of quantum dot cores. A non-injection approach may also be used. The optical properties of the quantum dots synthesized by this new approach can be finely tuned for a variety of applications by controlling size and/or composition of size and composition. Further, using the same approach, a shell can be grown around a quantum dot core that improves stability, luminescence efficiency, and may reduce toxicity.

  18. Organic synthesis

    International Nuclear Information System (INIS)

    Lallemand, J.Y.; Fetizon, M.

    1988-01-01

    The 1988 progress report of the Organic Synthesis Chemistry laboratory (Polytechnic School, France), is presented. The laboratory activities are centered on the chemistry of natural products, which have a biological activity and on the development of new reactions, useful in the organic synthesis. The research works involve the following domains: the natural products chemistry which are applied in pharmacology, the plants and insects chemistry, the organic synthesis, the radical chemistry new reactions and the bio-organic physicochemistry. The published papers, the congress communications and the thesis are listed [fr

  19. Chemistry of the transactinide elements

    International Nuclear Information System (INIS)

    Schaedel, Matthias

    1996-01-01

    Synthesis and decay of elements in the upper end of periodic table (z=104 to 111) are described. In view of very short half-life of about 1 s, the production of the transactinide isotopes and their transport to the separation and detection chamber are to be necessarily carried out employing fast and reliable techniques. Advances in microchemical separation techniques such as OLGA-II, HEVI, ARCA-II and SISAK, coupled to sensitive detection methods enable the detection of these heavier transactinide elements at atomic level. Their position in the periodic table and similarities, if any, with the corresponding lighter homologs are discussed based on their predicted and observed chemical behaviour. (author). 70 refs., 15 figs

  20. Experimental search for superheavy elements

    International Nuclear Information System (INIS)

    Wieloch, A.

    2008-12-01

    This work reports on the experimental search for superheavy elements (SHE). Two types of approaches for SHE production are studied i.e. '' cold '' fusion mechanism and massive transfer mechanism. First mechanism was studied in normal and inverse kinematics, by using Wien filter at the GANIL facility. The production of SHE elements with Z 106 and 108 is reported while negative results on the synthesis of SHE elements with Z 114 and 118 was received. The other approach i.e. reactions induced by heavy ion projectiles (e.g. 172 Yb, 197 Au) on fissile target nuclei (e.g. 238 U, 232 Th) at near Coulomb barrier incident energies was studied by using superconducting solenoid installed Texas A(and)M University. Preliminary results for the reaction 197 Au(7.5 MeV/u) - 232 Th are presented where three cases of the possible candidates for SHE elements were found. A dedicated detection setup for such studies is discussed and the detailed data analysis is presented. Detection of alpha and spontaneous fission radioactive decays is used to unambiguously identify the atomic number of SHE. Special statistical analysis for a very low detected number of α decays is applied to check consistency of the αradioactive chains. (author)

  1. Feature-aware natural texture synthesis

    KAUST Repository

    Wu, Fuzhang

    2014-12-04

    This article presents a framework for natural texture synthesis and processing. This framework is motivated by the observation that given examples captured in natural scene, texture synthesis addresses a critical problem, namely, that synthesis quality can be affected adversely if the texture elements in an example display spatially varied patterns, such as perspective distortion, the composition of different sub-textures, and variations in global color pattern as a result of complex illumination. This issue is common in natural textures and is a fundamental challenge for previously developed methods. Thus, we address it from a feature point of view and propose a feature-aware approach to synthesize natural textures. The synthesis process is guided by a feature map that represents the visual characteristics of the input texture. Moreover, we present a novel adaptive initialization algorithm that can effectively avoid the repeat and verbatim copying artifacts. Our approach improves texture synthesis in many images that cannot be handled effectively with traditional technologies.

  2. Synthesis of New Benzocoumaryl Oxadiazolyls as Strong Blue ...

    African Journals Online (AJOL)

    NICO

    complexes in DSSCs.5 Beside this, in support of our investiga- ... synthesis and fluorescent studies on benzocoumarins12 and development of new heterocyclic ..... characterized by elemental analysis and spectroscopic data. 3.1. UV-visible ...

  3. Methods of Synthesis of Automatic Control Systems with Delay

    Directory of Open Access Journals (Sweden)

    Aliaksandr Lapeta

    2013-05-01

    Full Text Available The paper investigates the procedure for introduction of systems containing delay elements. Shortcomings and difficulties in the synthesis of regulators and precompensators of control systems with delays in output and control channel where determined. The author focused on two approaches for the formation of promatrix and synthesis of control systems, considering the factor of delay.

  4. Discrete Element Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Morris, J; Johnson, S

    2007-12-03

    The Distinct Element Method (also frequently referred to as the Discrete Element Method) (DEM) is a Lagrangian numerical technique where the computational domain consists of discrete solid elements which interact via compliant contacts. This can be contrasted with Finite Element Methods where the computational domain is assumed to represent a continuum (although many modern implementations of the FEM can accommodate some Distinct Element capabilities). Often the terms Discrete Element Method and Distinct Element Method are used interchangeably in the literature, although Cundall and Hart (1992) suggested that Discrete Element Methods should be a more inclusive term covering Distinct Element Methods, Displacement Discontinuity Analysis and Modal Methods. In this work, DEM specifically refers to the Distinct Element Method, where the discrete elements interact via compliant contacts, in contrast with Displacement Discontinuity Analysis where the contacts are rigid and all compliance is taken up by the adjacent intact material.

  5. Synthesis of attapulgite clay at the rate of Fe/sub 2/O/sub 3/ composite via ionic liquid and its application in the oxidation of elemental mercury

    International Nuclear Information System (INIS)

    Cang, H.; Jing, Y.L.; Shao, J.L.; Xu, Q.

    2013-01-01

    Attapulgite clay at the rate Fe/sub 2/O/sub 3/ (ATP at the rate Fe/sub 2/O/sub 3/) composite was prepared by a one-pot calcination process via the ionic liquid (IL), (bmim)PF6, using two cheap, ecofriendly materials (i.e., Fe(NO/sub3/)sub 3/9H/sub 2/O and ATP, which is a magnesium aluminum silicate that is abundant in nature). The resulting composite was characterized by different techniques. IR spectra indicated that the ATP clay has been successfully modified by the functional Fe/sub 2/O/sub 3/ species. X-ray diffraction analysis demonstrated that the natural ATP still existed in ATP at the rate Fe/sub 2/O/sub 3/ composite and plays the role as a template. The specific surface areas determined by the BET method from N2 sorption isotherms decreased with the entrance of Fe/sub 2/O/sub 3/. The activity for oxidation of elemental mercury (Hg) in flue gases was investigated, which exhibited the highest efficiency value of 91% at 220 degree C. The results showed that this composite was qualified for controlling and removing Hg in flue gases as a low-cost, sustainable, effective catalyst. (author)

  6. Synthesis and characterization of a novel aminopolycarboxylate complexant for efficient trivalent f-element differentiation: N-butyl-2-acetamide-diethylenetriamine-N,N',N",N"-tetraacetic acid

    Energy Technology Data Exchange (ETDEWEB)

    Heathman, Colt R. [Idaho National Lab. (INL), Idaho Falls, ID (United States). Aqueous Separations and Radiochemistry Dept.; Grimes, Travis S. [Idaho National Lab. (INL), Idaho Falls, ID (United States). Aqueous Separations and Radiochemistry Dept.; Jansone-Popova, Santa [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Ivanov, Alexander S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Bryantsev, Vyacheslav S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Chemical Sciences Division; Zalupski, Peter R. [Idaho National Lab. (INL), Idaho Falls, ID (United States). Aqueous Separations and Radiochemistry Dept.

    2017-12-14

    The novel metal ion complexant N-butyl-2-acetamide-diethylenetriamine-N,N',N",N"-tetraacetic acid (DTTA-BuA) uses an amide functionalization to increase the total ligand acidity and attain efficient 4f/5f differentiation in low pH conditions. The amide, when located on the diethylenetriamine platform containing four acetate pendant arms maintains the octadentate coordination sphere for all investigated trivalent f-elements. This compact coordination environment inhibits the protonation of LnL- complexes, as indicated by lower K111 constants relative to the corresponding protonation site of the free ligand. For actinide ions, the enhanced stability of AnL- lowers the K111 for americium and curium beyond the aptitude of potentiometric detection. Density functional theory computations indicate the difference in the back-donation ability of Am3+ and Eu3+ f-orbitals is mainly responsible for stronger proton affinity of EuL- compared to AmL-. The measured stability constants for the formation of AmL- and CmL- complexes are consistently higher, relative to ML- complexes with lanthanides of similar charge density. When compared with the conventional aminopolycarboxylate diethylenetriamine pentaacetic acid (DTPA), the modified DTTA-BuA complexant features higher ligand acidity and the important An3+/Ln3+ differentiation when deployed on a liquid–liquid distribution platform.

  7. Synthesis of nano-sized hydrogen phosphate-imprinted polymer in acetonitrile/water mixture and its use as a recognition element of hydrogen phosphate selective all-solid state potentiometric electrode.

    Science.gov (United States)

    Alizadeh, Taher; Atayi, Khalil

    2018-02-01

    Herein, a new recipe is introduced for the preparation of hydrogen phosphate ion-imprinted polymer nanoparticles (nano-IIP) in acetonitrile/water (63.5:36.5) using phosphoric acid as the template. The nano-IIP obtained was used as the recognition element of a carbon paste potentiometric sensor. The IIP electrode showed a Nernstian response to hydrogen phosphate anion; whereas, the non-imprinted polymer (NIP)-based electrode had no considerable sensitivity to the anion. The presence of both methacrylic acid and vinyl pyridine in the IIP structure, as well as optimization of the functional monomers-template proportion, was found to be important to observe the sensing capability of the IIP electrode. The nano-IIP electrode showed a dynamic linear range of 1 × 10 -5 -1 × 10 -1  mol L-1, Nernstian slope of 30.6 ± (0.5) mV decade -1 , response time of 25 seconds, and detection limit of 4.0 × 10 -6  mol L -1 . The utility of the electrodes was checked by potentiometric titration of hydrogen phosphate with La 3+ solution. Copyright © 2017 John Wiley & Sons, Ltd.

  8. Chemistry of the elements

    International Nuclear Information System (INIS)

    Greenwood, N.N.; Earnshaw, A.

    1984-01-01

    This textbook presents an account of the chemistry of the elements for both undergraduate and postgraduate students. It covers not only the 'inorganic' chemistry of the elements, but also analytical, theoretical, industrial, organometallic;, bio-inorganic and other areas of chemistry which apply. The following elements of special nuclear interest are included: Rb, Cs, Fr, Sr, Ba, Ra, Po, At, Rn, Sc, Y, Zr, Hf, V, Nb, Ta, Mo, Tc, Ru, the Lanthanide Elements, the Actinide Elements. (U.K.)

  9. Dynamic analysis of pipings by Modal Synthesis

    International Nuclear Information System (INIS)

    Augusto, O.B.; Mattar Neto, M.

    1986-01-01

    A Modal Synthesis method, the component modes, and its implementation as a post-processor of finite element program is presented. Examples of calculations of stationary and transient vibrations for monitoring pipelines of nuclear power plants are analysed. (M.C.K.) [pt

  10. Protein synthesis controls phosphate homeostasis.

    Science.gov (United States)

    Pontes, Mauricio H; Groisman, Eduardo A

    2018-01-01

    Phosphorus is an essential element assimilated largely as orthophosphate (Pi). Cells respond to Pi starvation by importing Pi from their surroundings. We now report that impaired protein synthesis alone triggers a Pi starvation response even when Pi is plentiful in the extracellular milieu. In the bacterium Salmonella enterica serovar Typhimurium , this response entails phosphorylation of the regulatory protein PhoB and transcription of PhoB-dependent Pi transporter genes and is eliminated upon stimulation of adenosine triphosphate (ATP) hydrolysis. When protein synthesis is impaired due to low cytoplasmic magnesium (Mg 2+ ), Salmonella triggers the Pi starvation response because ribosomes are destabilized, which reduces ATP consumption and thus free cytoplasmic Pi. This response is transient because low cytoplasmic Mg 2+ promotes an uptake in Mg 2+ and a decrease in ATP levels, which stabilizes ribosomes, resulting in ATP consumption and Pi increase, thus ending the response. Notably, pharmacological inhibition of protein synthesis also elicited a Pi starvation response in the bacterium Escherichia coli and the yeast Saccharomyces cerevisiae Our findings identify a regulatory connection between protein synthesis and Pi homeostasis that is widespread in nature. © 2018 Pontes and Groisman; Published by Cold Spring Harbor Laboratory Press.

  11. Hydraulic elements in reduction of vibrations in mechanical systems

    Science.gov (United States)

    Białas, K.; Buchacz, A.

    2017-08-01

    This work presents non-classical method of design of mechanic systems with subsystem reducing vibrations. The purpose of this paper is also introduces synthesis of mechanic system with reducing vibrations understand as design of this type of systems. The synthesis may be applied to modify the already existing systems in order to achieve a desired result. Elements which reduce vibrations can be constructed with passive, semi-active or active components. These considerations systems have selected active items. A hallmark of active elements it is possible to change the parameters on time of these elements and their power from an external source. The implementation of active elements is very broad. These elements can be implemented through the use of components of electrical, pneumatic, hydraulic, etc. The system was consisted from mechanical and hydraulic elements. Hydraulic elements were used as subsystem reducing unwanted vibration of mechanical system. Hydraulic elements can be realized in the form of hydraulic cylinder. In the case of an active vibration reduction in the form of hydraulic cylinder it is very important to find the corresponding values of hydraulic components. The values of these elements affect the frequency of vibrations of this sub-system which is related to the effective vibration reduction [7,11].

  12. Data Element Registry Services

    Data.gov (United States)

    U.S. Environmental Protection Agency — Data Element Registry Services (DERS) is a resource for information about value lists (aka code sets / pick lists), data dictionaries, data elements, and EPA data...

  13. Basic Finite Element Method

    International Nuclear Information System (INIS)

    Lee, Byeong Hae

    1992-02-01

    This book gives descriptions of basic finite element method, which includes basic finite element method and data, black box, writing of data, definition of VECTOR, definition of matrix, matrix and multiplication of matrix, addition of matrix, and unit matrix, conception of hardness matrix like spring power and displacement, governed equation of an elastic body, finite element method, Fortran method and programming such as composition of computer, order of programming and data card and Fortran card, finite element program and application of nonelastic problem.

  14. Radiolabelled cellular blood elements

    International Nuclear Information System (INIS)

    Sinzinger, H.

    1990-01-01

    This book reports on radiolabelled cellular blood elements, covering new advances made during the past several years, in particular the use of Tc-99 as a tracer for blood elements. Coverage extends to several radiolabelled monoclonal antibodies that are specific for blood components and may label blood elements in vivo

  15. Rare (Earth Elements [score

    Directory of Open Access Journals (Sweden)

    Camilo Méndez

    2014-12-01

    Full Text Available Rare (Earth Elements is a cycle of works for solo piano. The cycle was inspired by James Dillon’s Book of Elements (Vol. I-V. The complete cycle will consist of 14 pieces; one for each selected rare (earth element. The chosen elements are Neodymium, Erbium, Tellurium, Hafnium, Tantalum, Technetium, Indium, Dysprosium, Lanthanium, Cerium, Europium, Terbium, Yttrium and Darmstadtium. These elements were selected due to their special atomic properties that in many cases make them extremely valuable for the development of new technologies, and also because of their scarcity. To date, only 4 works have been completed Yttrium, Technetium, Indium and Tellurium.

  16. Generalized finite elements

    International Nuclear Information System (INIS)

    Wachspress, E.

    2009-01-01

    Triangles and rectangles are the ubiquitous elements in finite element studies. Only these elements admit polynomial basis functions. Rational functions provide a basis for elements having any number of straight and curved sides. Numerical complexities initially associated with rational bases precluded extensive use. Recent analysis has reduced these difficulties and programs have been written to illustrate effectiveness. Although incorporation in major finite element software requires considerable effort, there are advantages in some applications which warrant implementation. An outline of the basic theory and of recent innovations is presented here. (authors)

  17. Horizontal variation in trace elements and soil characteristics at ...

    African Journals Online (AJOL)

    2016-10-04

    Oct 4, 2016 ... Soil indicators – pH, soil organic matter (SOM) and soil water retention (SWR) – were also ... The determination of total extractable trace element concen- ..... Tshipise soil. Factor 1. Factor 2. Factor 1. Factor 2. Li. −0.497. 0.176 ..... KABANDA TA (2003) Climate in A first synthesis of the environmental, bio-.

  18. Limitless Analytic Elements

    Science.gov (United States)

    Strack, O. D. L.

    2018-02-01

    We present equations for new limitless analytic line elements. These elements possess a virtually unlimited number of degrees of freedom. We apply these new limitless analytic elements to head-specified boundaries and to problems with inhomogeneities in hydraulic conductivity. Applications of these new analytic elements to practical problems involving head-specified boundaries require the solution of a very large number of equations. To make the new elements useful in practice, an efficient iterative scheme is required. We present an improved version of the scheme presented by Bandilla et al. (2007), based on the application of Cauchy integrals. The limitless analytic elements are useful when modeling strings of elements, rivers for example, where local conditions are difficult to model, e.g., when a well is close to a river. The solution of such problems is facilitated by increasing the order of the elements to obtain a good solution. This makes it unnecessary to resort to dividing the element in question into many smaller elements to obtain a satisfactory solution.

  19. Enaminone in heterocyclic synthesis: synthesis of new pyrazolopyrazole, pyrazolothienooxazine and pyrazolothienopyridine derivatives

    International Nuclear Information System (INIS)

    Hafiz, I.S.; Rahim, M.A.M.A.

    2014-01-01

    The chemical reactivity of enaminone 2 toward some nucleophilic and electrophilic reagents was investigated. Enaminone 2 was used as a key precursor for the synthesis of many important heterocyclic compounds. The synthesized compounds were characterized by IR, 1H-NMR, MS spectral and elemental analysis. (author)

  20. The solar element

    DEFF Research Database (Denmark)

    Kragh, Helge

    2009-01-01

    of the nineteenth century. In the modest form of a yellow spectral line known as D3, 'helium' was sometimes supposed to exist in the Sun's atmosphere, an idea which is traditionally ascribed to J. Norman Lockyer. Did Lockyer discover helium as a solar element? How was the suggestion received by chemists, physicists...... and astronomers in the period until the spring of 1895, when William Ramsay serendipitously found the gas in uranium minerals? The hypothetical element helium was fairly well known, yet Ramsay's discovery owed little or nothing to Lockyer's solar element. Indeed, for a brief while it was thought that the two...... elements might be different. The complex story of how helium became established as both a solar and terrestrial element involves precise observations as well as airy speculations. It is a story that is unique among the discovery histories of the chemical elements....

  1. The synthetic elements

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, D.C.

    1990-05-01

    Prior to 1940, the heaviest element known was uranium, discovered in 1789. Since that time the elements 93 through 109 have been synthesized and identified and the elements 43, 61, 85, and 87 which were missing form the periodic tables of the 1930's have been discovered. The techniques and problems involved in these discoveries and the placement of the transuranium elements in the periodic table will be discussed. The production and positive identification of elements heavier than Md (Z=101), which have very short half-lives and can only be produced an atom-at-a-time, are very difficult and there have been controversies concerning their discovery. Some of the new methods which have been developed and used in these studies will be described. The prospects for production of still heavier elements will be considered.

  2. The synthetic elements

    International Nuclear Information System (INIS)

    Hoffman, D.C.

    1990-05-01

    Prior to 1940, the heaviest element known was uranium, discovered in 1789. Since that time the elements 93 through 109 have been synthesized and identified and the elements 43, 61, 85, and 87 which were missing form the periodic tables of the 1930's have been discovered. The techniques and problems involved in these discoveries and the placement of the transuranium elements in the periodic table will be discussed. The production and positive identification of elements heavier than Md (Z=101), which have very short half-lives and can only be produced an atom-at-a-time, are very difficult and there have been controversies concerning their discovery. Some of the new methods which have been developed and used in these studies will be described. The prospects for production of still heavier elements will be considered

  3. Fuel element loading system

    International Nuclear Information System (INIS)

    Arya, S.P; s.

    1978-01-01

    A nuclear fuel element loading system is described which conveys a plurality of fuel rods to longitudinal passages in fuel elements. Conveyor means successively position the fuel rods above the longitudinal passages in axial alignment therewith and adapter means guide the fuel rods from the conveyor means into the longitudinal passages. The fuel elements are vibrated to cause the fuel rods to fall into the longitudinal passages through the adapter means

  4. Elements in biological AMS

    International Nuclear Information System (INIS)

    Vogel, J.S.; McAninch, J.; Freeman, S.

    1996-08-01

    AMS (Accelerator Mass Spectrometry) provides high detection sensitivity for isotopes whose half-lives are between 10 years and 100 million years. 14 C is the most developed of such isotopes and is used in tracing natural and anthropogenic organic compounds in the Earth's biosphere. Thirty-three elements in the main periodic table and 17 lanthanides or actinides have long lived isotopes, providing potential tracers for research in elemental biochemistry. Overlap of biologically interesting heavy elements and possible AMS tracers is discussed

  5. Analogs for transuranic elements

    International Nuclear Information System (INIS)

    Weimer, W.C.; Laul, J.C.; Kutt, J.C.

    1981-01-01

    A combined theoretical and experimental approach is being used to estimate the long-term environmental and biogeochemical behaviors of selected transuranic elements. The objective of this research is to estimate the effect that long-term (hundreds of years) environmental weathering has on the behavior of the transuranic elements americium and curium. This is achieved by investigating the actual behavior of naturally occurring rare earth elements, especially neodymium, that serve as transuranic analogs. Determination of the analog element behavior provides data that can be used to estimate the ultimate availability to man of transuranic materials released into the environment

  6. Synthesis of fermium and transfermium elements using calcium-48 beam

    International Nuclear Information System (INIS)

    Gupta, R.K.; Sandulescu, A.; Greiner, W.

    1977-06-01

    The fragmentation theory is used to suggest the possible targets to be used with the 48 Ca ion beam produced recently at the JINR U-30O heavy-ion cyclotron. Calculations are made for 100 252 102. (author)

  7. Analysis and Synthesis of Adaptive Neural Elements and Assembles

    Science.gov (United States)

    1993-09-30

    of an Aplysia sensory neuron was developed that reflects the subcellular processes underlying activity-dependent neuromodulation . This single- Page -3... neuromodulation learning rule could simulate some higher-order features of classical conditioning, such second-order conditioning and blocking. During the...reporting period, simulations were used to test the hypothesis that activity-dependent neuromodulation could also support operant conditioning. A

  8. Analysis and Synthesis of Adaptive Neural Elements and Assemblies

    Science.gov (United States)

    1992-12-14

    network, a learning rule (activity-dependent neuromodulation ), which has been proposed as a cellular mechanism for classical conditioning , was...activity-dependent neuromodulation ), which has been proposed as a cellular mechanism for classical conditioning, was demonstrated to support many...network, a learning rule (activity-dependent neuromodulation ), which has been proposed as a cellular mechanism for classical conditioning, was

  9. Total synthesis of ciguatoxin.

    Science.gov (United States)

    Hamajima, Akinari; Isobe, Minoru

    2009-01-01

    Something fishy: Ciguatoxin (see structure) is one of the principal toxins involved in ciguatera poisoning and the target of a total synthesis involving the coupling of three segments. The key transformations in this synthesis feature acetylene-dicobalthexacarbonyl complexation.

  10. Seagrass leaf element content

    NARCIS (Netherlands)

    Vonk, J.A.; Smulders, Fee O.H.; Christianen, Marjolijn J.A.; Govers, Laura L.

    2017-01-01

    Knowledge on the role of seagrass leaf elements and in particular micronutrients and their ranges is limited. We present a global database, consisting of 1126 unique leaf values for ten elements, obtained from literature and unpublished data, spanning 25 different seagrass species from 28 countries.

  11. Berkeley new element program

    International Nuclear Information System (INIS)

    Ghiorso, A.

    1975-09-01

    The work done with element 106 is reviewed, and a new experiment which bears on the properties of the isotope of mass 260 with atomic number 104 is discussed. It is noted that in the case of element 106 a link is demonstrated to the granddaughter as well as the daughter

  12. Elemental Food for Thought

    Science.gov (United States)

    Cady, Susan

    2005-01-01

    One of the first tasks students learn in chemistry is to pronounce and spell the names of elements and learn their corresponding chemical symbols. Repetitive oral recitation is commonly used to learn this information, but games and puzzles can make this task creative, variable, and fun. Elemental Food for Thought is a puzzlelike activity that…

  13. Nuclear fuel element

    International Nuclear Information System (INIS)

    Mogard, J.H.

    1977-01-01

    A nuclear fuel element is disclosed for use in power producing nuclear reactors, comprising a plurality of axially aligned ceramic cylindrical fuel bodies of the sintered type, and a cladding tube of metal or metal alloys, wherein said cladding tube on its cylindrical inner surface is provided with a plurality of slightly protruding spacing elements distributed over said inner surface

  14. Origin and distribution of the elements

    International Nuclear Information System (INIS)

    Pagel, B.E.J.

    1987-01-01

    In the solar neighborhood they have mass fractions of about 70% hydrogen, 28% helium and 1 or 2% heavier elements, mostly O, C, Ne, N, Mg, Si, Fe. Most of the helium comes from nucleosynthesis in the Big Bang, which also produced traces of D, 3 He and 7 Li, while the remainder can largely be accounted for by synthesis in stars and subsequent ejection into the interstellar medium in the form of supernova ejecta, planetary nebulae and stellar winds. Information about these processes can be obtained on the one hand by theoretical computations and observations of stars in advanced stages of evolution and on the other by studying the distribution of detectable elements in different parts of different galaxies and in different stellar populations. Some observational results bearing on the extrapolation of observed abundances back to the Big Bang, and on the evolution of galaxies, are described

  15. Discovery of element 112

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, S. [GSI, Darmstadt (Germany)

    1996-12-31

    The new elements 110, 111, and 112 were synthesized and unambiguously identified in experiments at SHIP. Due to strong shell effects the dominant decay mode is not fission, but emission of alpha particles. Theoretical investigations predict that maximum shell effects should exist in nuclei near proton number 114 and neutron number 184. Measurements give hope that isotopes of element 114 close to the island of spherical Superheavy Elements could be produced by fusion reactions using {sup 118}Pb as target. systematic studies of the reaction cross-sections indicate that transfer of nucleons is the important process to initiate the fusion.

  16. Nuclear fuel element

    International Nuclear Information System (INIS)

    Grossman, L.N.; Levin, H.A.

    1975-01-01

    A nuclear fuel element has disposed therein an alloy having the essential components of nickel, titanium and zirconium, and the alloy reacts with water, water vapor and reactive gases at reactor ambient temperatures. The alloy is disposed in the plenum of the fuel element in the form of particles in a hollow gas permeable container having a multiplicity of openings of size smallr than the size of the particles. The container is preferably held in the spring in the plenum of the fuel element. (E.C.B.)

  17. Elemental diffusion in stars

    International Nuclear Information System (INIS)

    Michaud, Georges; Montmerle, Thierry

    1977-01-01

    This paper is dealing with the origin of the elements in the universe. The scheme of nucleosynthesis is kept to explain the stellar generation of helium, carbon, etc... from the initial hydrogen; but a nonlinear theory is then elaborated to account for the anomalous abundances which were observed. The chemical elements would diffuse throughout the outer layers of a star under the action of the opposite forces of gravitation and radiation. This theory, with completing the nucleosynthesis, would contribute to give a consistent scheme of the elemental origin and abundances [fr

  18. Bridge element deterioration rates.

    Science.gov (United States)

    2008-10-01

    This report describes the development of bridge element deterioration rates using the NYSDOT : bridge inspection database using Markov chains and Weibull-based approaches. It is observed : that Weibull-based approach is more reliable for developing b...

  19. 2. Transuranic elements

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    Methods of sample collection, sample storage, sample procedures and radioanalytical procedures for transuranic elements in marine environment are reviewed and recommended. Alpha spectrometry and scintillation techniques are used for measurement of isotopic content. Separation processes for samples are described

  20. Heavy element research

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    Heavy element research activities in metallurgy and ceramics during 1976 at Lawrence Berkeley Laboratory are reviewed. Topics include: microstructure, properties and alloy design; ceramic alloy program; high resolution and high voltage electron microscopy; and powder metallurgy

  1. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E.D.

    1981-01-01

    An array of rods comprising zirconium alloy sheathed nuclear fuel pellets assembled to form a fuel element for a pressurised water reactor is claimed. The helium gas pressure within each rod differs substantially from that of its closest neighbours

  2. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E.D.

    1984-01-01

    The fuel elements for a pressurised water reactor comprise arrays of rods of zirconium alloy sheathed nuclear fuel pellets. The helium gas pressure within each rod differs substantially from that of its closest neighbours

  3. Transposable elements in cancer.

    Science.gov (United States)

    Burns, Kathleen H

    2017-07-01

    Transposable elements give rise to interspersed repeats, sequences that comprise most of our genomes. These mobile DNAs have been historically underappreciated - both because they have been presumed to be unimportant, and because their high copy number and variability pose unique technical challenges. Neither impediment now seems steadfast. Interest in the human mobilome has never been greater, and methods enabling its study are maturing at a fast pace. This Review describes the activity of transposable elements in human cancers, particularly long interspersed element-1 (LINE-1). LINE-1 sequences are self-propagating, protein-coding retrotransposons, and their activity results in somatically acquired insertions in cancer genomes. Altered expression of transposable elements and animation of genomic LINE-1 sequences appear to be hallmarks of cancer, and can be responsible for driving mutations in tumorigenesis.

  4. Divergent picornavirus IRES elements

    DEFF Research Database (Denmark)

    Belsham, Graham

    2009-01-01

    Internal ribosome entry site (IRES) elements were first identified about 20 years ago within the 5' untranslated region of picornavirus RNAs. They direct a cap-independent mechanism of translation initiation on the viral RNA. Within the picornavirus family it is now known that there are four...... classes of IRES element which vary in size (450-270nt), they also have different, complex, secondary structures and distinct requirements for cellular proteins to allow them to function. This review describes the features of each class of picornavirus IRES element but focuses on the characteristics...... of the most recently described group, initially identified within the porcine teschovirus-1 RNA, which has strong similarities to the IRES elements from within the genomes of hepatitis C virus and the pestiviruses which are members of the flavivirus family. The selection of the initiation codon...

  5. Improved synthesis of (S)-N-Boc-5-oxaproline for protein synthesis with the α-ketoacid-hydroxylamine (KAHA) ligation.

    Science.gov (United States)

    Murar, Claudia E; Harmand, Thibault J; Bode, Jeffrey W

    2017-09-15

    We describe a new route for the synthesis of (S)-N-Boc-5-oxaproline. This building block is a key element for the chemical synthesis of proteins with the α-ketoacid-hydroxylamine (KAHA) ligation. The new synthetic pathway to the enantiopure oxaproline is based on a chiral amine mediated enantioselective conjugate addition of a hydroxylamine to trans-4-oxo-2-butenoate. This route is practical, scalable and economical and provides decagram amounts of material for protein synthesis and conversion to other protected forms of (S)-oxaproline. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Novel porcine repetitive elements

    Directory of Open Access Journals (Sweden)

    Nonneman Dan J

    2006-12-01

    Full Text Available Abstract Background Repetitive elements comprise ~45% of mammalian genomes and are increasingly known to impact genomic function by contributing to the genomic architecture, by direct regulation of gene expression and by affecting genomic size, diversity and evolution. The ubiquity and increasingly understood importance of repetitive elements contribute to the need to identify and annotate them. We set out to identify previously uncharacterized repetitive DNA in the porcine genome. Once found, we characterized the prevalence of these repeats in other mammals. Results We discovered 27 repetitive elements in 220 BACs covering 1% of the porcine genome (Comparative Vertebrate Sequencing Initiative; CVSI. These repeats varied in length from 55 to 1059 nucleotides. To estimate copy numbers, we went to an independent source of data, the BAC-end sequences (Wellcome Trust Sanger Institute, covering approximately 15% of the porcine genome. Copy numbers in BAC-ends were less than one hundred for 6 repeat elements, between 100 and 1000 for 16 and between 1,000 and 10,000 for 5. Several of the repeat elements were found in the bovine genome and we have identified two with orthologous sites, indicating that these elements were present in their common ancestor. None of the repeat elements were found in primate, rodent or dog genomes. We were unable to identify any of the replication machinery common to active transposable elements in these newly identified repeats. Conclusion The presence of both orthologous and non-orthologous sites indicates that some sites existed prior to speciation and some were generated later. The identification of low to moderate copy number repetitive DNA that is specific to artiodactyls will be critical in the assembly of livestock genomes and studies of comparative genomics.

  7. Fuel element store

    International Nuclear Information System (INIS)

    Wieser, R.

    1987-01-01

    The spherical fuel elements are stored dry in cans. The cans themselves are stacked in parallel storage shafts, which are combined into a rectangular storage space. The storage space is made earthquake-proof by surrounding it with concrete. It consists of a ceiling assembled from several steel parts, which is connected to the floor by support elements. A cooling air ventilation station supplies the individual storage shaft and therefore the cans with cooling air via incoming and outgoing pipes. (DG) [de

  8. Intrusion detection system elements

    International Nuclear Information System (INIS)

    Eaton, M.J.; Mangan, D.L.

    1980-09-01

    This report highlights elements required for an intrusion detection system and discusses problems which can be encountered in attempting to make the elements effective. Topics discussed include: sensors, both for exterior detection and interior detection; alarm assessment systems, with the discussion focused on video assessment; and alarm reporting systems, including alarm communication systems and dislay/console considerations. Guidance on careful planning and design of a new or to-be-improved system is presented

  9. Structural elements design manual

    CERN Document Server

    Draycott, Trevor

    2012-01-01

    Gives clear explanations of the logical design sequence for structural elements. The Structural Engineer says: `The book explains, in simple terms, and with many examples, Code of Practice methods for sizing structural sections in timber, concrete,masonry and steel. It is the combination into one book of section sizing methods in each of these materials that makes this text so useful....Students will find this an essential support text to the Codes of Practice in their study of element sizing'.

  10. Atoms, molecules & elements

    CERN Document Server

    Graybill, George

    2007-01-01

    Young scientists will be thrilled to explore the invisible world of atoms, molecules and elements. Our resource provides ready-to-use information and activities for remedial students using simplified language and vocabulary. Students will label each part of the atom, learn what compounds are, and explore the patterns in the periodic table of elements to find calcium (Ca), chlorine (Cl), and helium (He) through hands-on activities.

  11. Nuclear fuel element

    International Nuclear Information System (INIS)

    Penrose, R.T.; Thompson, J.R.

    1976-01-01

    A method of protecting the cladding of a nuclear fuel element from internal attack and a nuclear fuel element for use in the core of a nuclear reactor are disclosed. The nuclear fuel element has disposed therein an additive of a barium-containing material and the barium-containing material collects reactive gases through chemical reaction or adsorption at temperatures ranging from room temperature up to fuel element plenum temperatures. The additive is located in the plenum of the fuel element and preferably in the form of particles in a hollow container having a multiplicity of gas permeable openings in one portion of the container with the openings being of a size smaller than the size of the particles. The openings permit gases and liquids entering the plenum to contact the particles. The additive is comprised of elemental barium or a barium alloy containing one or more metals in addition to barium such as aluminum, zirconium, nickel, titanium and combinations thereof. 6 claims, 3 drawing figures

  12. High Throughput Synthesis and Screening for Agents Inhibiting Androgen Receptor Mediated Gene Transcription

    National Research Council Canada - National Science Library

    Boger, Dale L

    2005-01-01

    .... This entails the high throughput synthesis of DNA binding agents related to distamycin, their screening for binding to androgen response elements using a new high throughput DNA binding screen...

  13. High Throughout Synthesis and Screening for Agents Inhibiting Androgen Receptor Mediated Gene Transcription

    National Research Council Canada - National Science Library

    Boger, Dale

    2003-01-01

    .... This entails the high throughput synthesis of DNA binding agents related to distamycin, their screening for binding to androgen response elements using a new high throughput DNA binding screen...

  14. High Throughput Synthesis and Screening for Agents Inhibiting Androgen Receptor Mediated Gene Transcription

    National Research Council Canada - National Science Library

    Boger, Dale

    2004-01-01

    .... This entails the high throughput synthesis of DNA binding agents related to distamycin, their screening for binding to androgen response elements using a new high throughput DNA binding screen...

  15. Quantifying the promotion of Cu catalysts by ZnO for methanol synthesis

    DEFF Research Database (Denmark)

    Kuld, Sebastian; Thorhauge, Max; Falsig, Hanne

    2016-01-01

    Promoter elements enhance the activity and selectivity of heterogeneous catalysts. Here, we show how methanol synthesis from synthesis gas over copper (Cu) nanoparticles is boosted by zinc oxide (ZnO) nanoparticles. By combining surface area titration, electron microscopy, activity measurement, d...

  16. Exploring the Relevance of Qualitative Research Synthesis to Higher Education Research and Practice

    Science.gov (United States)

    Major, Claire; Savin-Baden, Maggi

    2010-01-01

    This paper proposes the importance of qualitative research synthesis to the field of higher education. It examines seven key texts that undertake synthesis in this field and compares essential features and elements across studies. The authors indicate strengths of the approaches and highlight ways forward for using qualitative research synthesis…

  17. Synthesis of pneumatic controll systems

    Directory of Open Access Journals (Sweden)

    D. Nowak

    2011-04-01

    Full Text Available Currently, the basic tool for automating the production processes are the PLCs. However, in many areas application of the pneumaticcontrol systems may be more reasonable. The main factor determining choice of the control technology are costs. In the case of pneumaticsystems, the costs shall be determined by the number of elements used. Therefore, during the design works it is important to choose anappropriate method for the pneumatic control systems synthesis. The article presents the MTS method, which may be used for a discretetechnological processes modeling and PLC programming, as well as for a pneumatic control systems designing. An important element ofthe MTS method is the network of actions, which graphically presents an algorithm of the implemented process. Based on the actionnetwork and operating machine’s functional diagram, the diagram of different states is determinated, which graphically shows changes ofthe control system’s input and output signals. Analysis of the diagram of different states, makes it easy to determine a schematic equation, which shall be the basis for the control system implementation. Advantage of the MTS method is the lack of restrictions on the number of the control system’s input and output signals. The resulting solution is characterized by a minimum number of elements needed to implement the control system.

  18. Increasing reconstruction quality of diffractive optical elements displayed with LC SLM

    Science.gov (United States)

    Cheremkhin, Pavel A.; Evtikhiev, Nikolay N.; Krasnov, Vitaly V.; Rodin, Vladislav G.; Starikov, Sergey N.

    2015-03-01

    Phase liquid crystal (LC) spatial light modulators (SLM) are actively used in various applications. However, majority of scientific applications require stable phase modulation which might be hard to achieve with commercially available SLM due to its consumer origin. The use of digital voltage addressing scheme leads to phase temporal fluctuations, which results in lower diffraction efficiency and reconstruction quality of displayed diffractive optical elements (DOE). Due to high periodicity of fluctuations it should be possible to use knowledge of these fluctuations during DOE synthesis to minimize negative effect. We synthesized DOE using accurately measured phase fluctuations of phase LC SLM "HoloEye PLUTO VIS" to minimize its negative impact on displayed DOE reconstruction. Synthesis was conducted with versatile direct search with random trajectory (DSRT) method in the following way. Before DOE synthesis begun, two-dimensional dependency of SLM phase shift on addressed signal level and time from frame start was obtained. Then synthesis begins. First, initial phase distribution is created. Second, random trajectory of consecutive processing of all DOE elements is generated. Then iterative process begins. Each DOE element sequentially has its value changed to one that provides better value of objective criterion, e.g. lower deviation of reconstructed image from original one. If current element value provides best objective criterion value then it left unchanged. After all elements are processed, iteration repeats until stagnation is reached. It is demonstrated that application of SLM phase fluctuations knowledge in DOE synthesis with DSRT method leads to noticeable increase of DOE reconstruction quality.

  19. Fuel element transport container

    International Nuclear Information System (INIS)

    Benna, P.; Neuenfeldt, W.

    1979-01-01

    The reprocessing system includes a large number of waterfilled ponds next to each other for the intermediate storage of fuel elements from LWR's. The fuel element transport device is allocated to a middle pond. The individual ponds are separated from each other by walls, and are only accessible from the middle pond via narrow passages. The transport device includes a telescopic running rail for a trolley with a grab device for the fuel element. The running rail is supported in turn by a second trolley, which can be moved by wheels on rails. Part of the drive of the first trolley is arranged on the second one. Using this transport device, adjacent ponds can be served through the passage openings. (DG) [de

  20. Nuclear fuel element

    International Nuclear Information System (INIS)

    Hirayama, Satoshi; Kawada, Toshiyuki; Matsuzaki, Masayoshi.

    1980-01-01

    Purpose: To provide a fuel element for reducing the mechanical interactions between a fuel-cladding tube and the fuel element and for alleviating the limits of the operating conditions of a reactor. Constitution: A fuel element having mainly uranium dioxide consists of a cylindrical outer pellet and cylindrical inner pellet inserted into the outer pellet. The outer pellet contains two or more additives selected from aluminium oxide, beryllium oxide, magnesium oxide, silicon oxide, sodium oxide, phosphorus oxide, calcium oxide and iron oxide, and the inner pellet contains nuclear fuel substance solely or one additive selected from calcium oxide, silicon oxide, aluminium oxide, magnesium oxide, zirconium oxide and iron oxide. The outer pellet of the fuel thus constituted is reduced in mechanical strength and also in the mechanical interactions with the cladding tube, and the plastic fluidity of the entire pellet is prevented by the inner pellet increased in the mechanical strength. (Kamimura, M.)

  1. Creativity Management Key Elements

    Directory of Open Access Journals (Sweden)

    Rosa María Fuchs Ángeles

    2015-09-01

    Full Text Available Organizations are constantly looking towards innovation. In order to reach it they must foment creativity. This paper analyzes a series of elements considered in the organizational creativity management and proposes a model with the indispensable factors that organizations should consider to reach it. These elements are: culture and organizational environment, strategy, structure, communication, relation with customers, human resources (recruiting, training, job design, compensation, promotion, and performance evaluation, long term orientation and the organizational life cycle. Having the analysis of those elements as a basis, the indispensable pillars on management creativity are identified. The proposed model is based on 5 pillars: the alignment between strategic, culture and organizational structure, called by the authors 'Holy Trinity'; intern publicity; customer’s voice; recognition and a look towards future. Finally, the case of an innovative Peruvian enterprise is presented from the model’s perspective and the study conclusions.

  2. Fuel Element Technical Manual

    Energy Technology Data Exchange (ETDEWEB)

    Burley, H.H. [ed.

    1956-08-01

    It is the purpose of the Fuel Element Technical Manual to Provide a single document describing the fabrication processes used in the manufacture of the fuel element as well as the technical bases for these processes. The manual will be instrumental in the indoctrination of personnel new to the field and will provide a single data reference for all personnel involved in the design or manufacture of the fuel element. The material contained in this manual was assembled by members of the Engineering Department and the Manufacturing Department at the Hanford Atomic Products Operation between the dates October, 1955 and June, 1956. Arrangement of the manual. The manual is divided into six parts: Part I--introduction; Part II--technical bases; Part III--process; Part IV--plant and equipment; Part V--process control and improvement; and VI--safety.

  3. Elements of social security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security is a comparative study of important elements of the social security systems in Denmark (DK), Sweden (S), Finland (FIN), Austria (A), Germany (D), the Netherlands (NL), Great Britain (GB) and Canada (CAN). It should be emphasized that Germany is the former West Germany...... (Alte Länder). This is the 9th and last edition of the publication,covering income levels and rules for social security and personal taxation for 1999. Basis for the projections to 1999 income levels is the 1998 data (in some cases 1999 data)for OECD's Taxing Wages as reported by national experts....

  4. Elements of linear space

    CERN Document Server

    Amir-Moez, A R; Sneddon, I N

    1962-01-01

    Elements of Linear Space is a detailed treatment of the elements of linear spaces, including real spaces with no more than three dimensions and complex n-dimensional spaces. The geometry of conic sections and quadric surfaces is considered, along with algebraic structures, especially vector spaces and transformations. Problems drawn from various branches of geometry are given.Comprised of 12 chapters, this volume begins with an introduction to real Euclidean space, followed by a discussion on linear transformations and matrices. The addition and multiplication of transformations and matrices a

  5. Bibliography on transuranium elements

    International Nuclear Information System (INIS)

    Sood, D.D.

    1991-01-01

    A selective bibliography of prominent publications on transuranium elements is compiled. Heading papers, symposia proceedings and the textbooks are included in the bibliography. The bibliography is arranged under the headings: (1)Books, Symposia Proceedings, Reviews etc., (2)Discovery, (3)Weighable Isolation, (4)Metal Preparation, (5)Nuclear Properties, (6)Plutonium as Reactor Fuel, (7)Fuel Reprocessing, (8)Solid State Chemistry, Thermochemistry and Spectroscopy, (9)Radiation Safety, (10)Applications, and (11)Some Typical Indian Papers. Total number of references cited are 298. The bibliography, though selective, will serve as a starting point for comprehensive literature search on transuranium elements. (author)

  6. Finite elements and approximation

    CERN Document Server

    Zienkiewicz, O C

    2006-01-01

    A powerful tool for the approximate solution of differential equations, the finite element is extensively used in industry and research. This book offers students of engineering and physics a comprehensive view of the principles involved, with numerous illustrative examples and exercises.Starting with continuum boundary value problems and the need for numerical discretization, the text examines finite difference methods, weighted residual methods in the context of continuous trial functions, and piecewise defined trial functions and the finite element method. Additional topics include higher o

  7. Big bang photosynthesis and pregalactic nucleosynthesis of light elements

    International Nuclear Information System (INIS)

    Audouze, J.; Lindley, D.; Silk, J.; and Laboratoire Rene Bernas, Orsay, France)

    1985-01-01

    Two nonstandard scenarios for pregalactic synthesis of the light elements ( 2 H, 3 He, 4 He, and 7 Li) are developed. Big bang photosynthesis occurs if energetic photons, produced by the decay of massive neutrinos or gravitinos, partially photodisintegrate 4 He (formed in the standard hot big bang) to produce 2 H and 3 He. In this case, primordial nucleosynthesis no longer constrains the baryon density of the universe, or the number of neutrino species. Alternatively, one may dispense partially or completely with the hot big bang and produce the light elements by bombardment of primordial gas, provided that 4 He is synthesized by a later generation of massive stars

  8. Big bang photosynthesis and pregalactic nucleosynthesis of light elements

    Science.gov (United States)

    Audouze, J.; Lindley, D.; Silk, J.

    1985-01-01

    Two nonstandard scenarios for pregalactic synthesis of the light elements (H-2, He-3, He-4, and Li-7) are developed. Big bang photosynthesis occurs if energetic photons, produced by the decay of massive neutrinos or gravitinos, partially photodisintegrate He-4 (formed in the standard hot big bang) to produce H-2 and He-3. In this case, primordial nucleosynthesis no longer constrains the baryon density of the universe, or the number of neutrino species. Alternatively, one may dispense partially or completely with the hot big bang and produce the light elements by bombardment of primordial gas, provided that He-4 is synthesized by a later generation of massive stars.

  9. Model Reduction in Dynamic Finite Element Analysis of Lightweight Structures

    DEFF Research Database (Denmark)

    Flodén, Ola; Persson, Kent; Sjöström, Anders

    2012-01-01

    models may be created by assembling models of floor and wall structures into large models of complete buildings. When assembling the floor and wall models, the number of degrees of freedom quickly increases to exceed the limits of computer capacity, at least in a reasonable amount of computational time...... Hz. Three different methods of model reduction were investigated; Guyan reduction, component mode synthesis and a third approach where a new finite element model was created with structural elements. Eigenvalue and steady-state analyses were performed in order to compare the errors...

  10. UBV light variation and orbital elements of W Gruis

    International Nuclear Information System (INIS)

    Cerruti, M.A.

    1987-01-01

    In each of the UBV band-passes 2440 observations define for the first time the photoelectric light variation of the binary system W Gru. A consistent set of elements is derived in the framework of Russell's classic and Napier's synthesis models. Absolute dimensions are derived. The system seems to be a well-detached binary consisting of two normal, not interacting, F5 4 components. 18 refs., 2 figs., 3 tabs. (author)

  11. Testing the ecological consequences of evolutionary change using elements.

    Science.gov (United States)

    Jeyasingh, Punidan D; Cothran, Rickey D; Tobler, Michael

    2014-02-01

    Understanding the ecological consequences of evolutionary change is a central challenge in contemporary biology. We propose a framework based on the ˜25 elements represented in biology, which can serve as a conduit for a general exploration of poorly understood evolution-to-ecology links. In this framework, known as ecological stoichiometry, the quantity of elements in the inorganic realm is a fundamental environment, while the flow of elements from the abiotic to the biotic realm is due to the action of genomes, with the unused elements excreted back into the inorganic realm affecting ecological processes at higher levels of organization. Ecological stoichiometry purposefully assumes distinct elemental composition of species, enabling powerful predictions about the ecological functions of species. However, this assumption results in a simplified view of the evolutionary mechanisms underlying diversification in the elemental composition of species. Recent research indicates substantial intraspecific variation in elemental composition and associated ecological functions such as nutrient excretion. We posit that attention to intraspecific variation in elemental composition will facilitate a synthesis of stoichiometric information in light of population genetics theory for a rigorous exploration of the ecological consequences of evolutionary change.

  12. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Austria, Germany, the Netherlands, Great Britain and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable...

  13. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Germany, the Netherlands, Great Britain and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable income...

  14. Elements of Social Security

    DEFF Research Database (Denmark)

    Hansen, Hans

    Elements of Social Security contains an overview of important benefit schemes in Denmark, Sweden, Finland, Germany, Great Britain, the Netherlands and Canada. The schemes are categorized according to common sets of criteria and compared. Stylized cases illustrate the impact on disposable income...

  15. Water, the intangible element

    NARCIS (Netherlands)

    Schotting, R.J.

    2009-01-01

    Water is the key to life. No living creature can survive without water. Too much water or polluted water are serious threats to mankind. Managing this intangible element is complex, not only in wet deltaic regions but also in the (semi-)arid regions of the world. Combined efforts of the

  16. Movies and Literary Elements.

    Science.gov (United States)

    Keller, Rodney D.

    1987-01-01

    Recommends using movie clips to stimulate students' interest in reading a novel as well as to teach elements of fiction such as plot, character, setting, symbol, irony, and theme. Describes each clip and provides study questions. Includes a listing of movies made from books. (NH)

  17. Elements of Architecture

    DEFF Research Database (Denmark)

    Elements of Architecture explores new ways of engaging architecture in archaeology. It conceives of architecture both as the physical evidence of past societies and as existing beyond the physical environment, considering how people in the past have not just dwelled in buildings but have existed...

  18. Inside finite elements

    CERN Document Server

    Weiser, Martin

    2016-01-01

    All relevant implementation aspects of finite element methods are discussed in this book. The focus is on algorithms and data structures as well as on their concrete implementation. Theory is covered as far as it gives insight into the construction of algorithms. Throughout the exercises a complete FE-solver for scalar 2D problems will be implemented in Matlab/Octave.

  19. Plants' essential chemical elements

    Science.gov (United States)

    Kevin T. Smith

    2007-01-01

    Every garden center and hardware store sells fertilizer guaranteed to "feed" plants. In a strict sense, we can't feed plants. Food contains an energy source. Green plants capture solar energy and make their own food through photosynthesis! Photosynthesis and other metabolic processes require chemical elements in appropriate doses for plants to survive...

  20. Elements of relativity theory

    International Nuclear Information System (INIS)

    Lawden, D.F.

    1985-01-01

    The book on elements of relativity theory is intended for final year school students or as an early university course in mathematical physics. Special principle of relativity, lorentz transformation, velocity transformations, relativistic mechanics, and general theory of relativity, are all discussed. (U.K.)

  1. Photovoltaic radiation detector element

    International Nuclear Information System (INIS)

    Agouridis, D.C.

    1980-01-01

    A radiation detector element is formed of a body of semiconductor material, a coating on the body which forms a photovoltaic junction therewith, and a current collector consisting of narrow metallic strips, the aforesaid coating having an opening therein in the edge of which closely approaches but is spaced from the current collector strips

  2. Hamiltonian Algorithm Sound Synthesis

    OpenAIRE

    大矢, 健一

    2013-01-01

    Hamiltonian Algorithm (HA) is an algorithm for searching solutions is optimization problems. This paper introduces a sound synthesis technique using Hamiltonian Algorithm and shows a simple example. "Hamiltonian Algorithm Sound Synthesis" uses phase transition effect in HA. Because of this transition effect, totally new waveforms are produced.

  3. Synthesis of Mechanisms

    DEFF Research Database (Denmark)

    Hansen, John Michael

    1999-01-01

    These notes describe an automated procedure for analysis and synthesis of mechanisms. The analysis method is based on the body coordinate formulation, and the synthesis is based on applying optimization methods, used to minimize the difference between an actual and a desired behaviour...

  4. Synthesis of oligonucleotide phosphorodithioates

    DEFF Research Database (Denmark)

    Beaton, G.; Brill, W. K D; Grandas, A.

    1991-01-01

    The synthesis of DNA containing sulfur at the two nonbonding internucleotide valencies is reported. Several different routes using either tervalent or pentavalent mononucleotide synthons are described.......The synthesis of DNA containing sulfur at the two nonbonding internucleotide valencies is reported. Several different routes using either tervalent or pentavalent mononucleotide synthons are described....

  5. Synthesis of Isoiminosugars

    DEFF Research Database (Denmark)

    Hyldtoft, Lene; Godskesen, Michael Anders; Lundt, Inge

    1998-01-01

    A short synthesis of isoiminosugars have been developed. Bromolactones are diastereoselectively alkylated at C-2 followed by ring closure to the corresponding lactams. Reduction of these then gives isoiminosugars......A short synthesis of isoiminosugars have been developed. Bromolactones are diastereoselectively alkylated at C-2 followed by ring closure to the corresponding lactams. Reduction of these then gives isoiminosugars...

  6. Element-topology-independent preconditioners for parallel finite element computations

    Science.gov (United States)

    Park, K. C.; Alexander, Scott

    1992-01-01

    A family of preconditioners for the solution of finite element equations are presented, which are element-topology independent and thus can be applicable to element order-free parallel computations. A key feature of the present preconditioners is the repeated use of element connectivity matrices and their left and right inverses. The properties and performance of the present preconditioners are demonstrated via beam and two-dimensional finite element matrices for implicit time integration computations.

  7. Integrated biofuels process synthesis

    DEFF Research Database (Denmark)

    Torres-Ortega, Carlo Edgar; Rong, Ben-Guang

    2017-01-01

    Second and third generation bioethanol and biodiesel are more environmentally friendly fuels than gasoline and petrodiesel, andmore sustainable than first generation biofuels. However, their production processes are more complex and more expensive. In this chapter, we describe a two-stage synthesis......% used for bioethanol process), and steam and electricity from combustion (54%used as electricity) in the bioethanol and biodiesel processes. In the second stage, we saved about 5% in equipment costs and 12% in utility costs for bioethanol separation. This dual synthesis methodology, consisting of a top......-level screening task followed by a down-level intensification task, proved to be an efficient methodology for integrated biofuel process synthesis. The case study illustrates and provides important insights into the optimal synthesis and intensification of biofuel production processes with the proposed synthesis...

  8. VHDL for logic synthesis

    CERN Document Server

    Rushton, Andrew

    2011-01-01

    Many engineers encountering VHDL (very high speed integrated circuits hardware description language) for the first time can feel overwhelmed by it. This book bridges the gap between the VHDL language and the hardware that results from logic synthesis with clear organisation, progressing from the basics of combinational logic, types, and operators; through special structures such as tristate buses, register banks and memories, to advanced themes such as developing your own packages, writing test benches and using the full range of synthesis types. This third edition has been substantially rewritten to include the new VHDL-2008 features that enable synthesis of fixed-point and floating-point hardware. Extensively updated throughout to reflect modern logic synthesis usage, it also contains a complete case study to demonstrate the updated features. Features to this edition include: * a common VHDL subset which will work across a range of different synthesis systems, targeting a very wide range of technologies...

  9. Hybrid principle with applications to synthesis

    International Nuclear Information System (INIS)

    Nanneh, M.M.

    1991-01-01

    The theory of hybrid principles is presented together with the transformation rule for converting odd-parity approximations into even-parity approximations. This rule leads to a method which provides rigorous upper and lower bounds for the disadvantage factor for a reactor lattice cell. With these bounds very precise benchmarks have been constructed for representative lattices. It is found that a combination of even and odd-parity solutions for the neutron flux is much more efficient than solutions based on either the even-parity or odd-parity. This is the basis of one synthesis scheme. In another synthesis method, a hybrid principle with trial functions for both the even- and odd- parity angular flux is used in conjunction with a classical principle with an odd-parity trial function. The synthesis process is efficient because the largest set of equations to be solved, i.e. the frame work, involves as few as one unknown per node of the finite element mesh. The effectiveness of the synthesis method is demonstrated for a thick shield problem. (author)

  10. Archaeal extrachromosomal genetic elements

    DEFF Research Database (Denmark)

    Wang, Haina; Peng, Nan; Shah, Shiraz Ali

    2015-01-01

    SUMMARY: Research on archaeal extrachromosomal genetic elements (ECEs) has progressed rapidly in the past decade. To date, over 60 archaeal viruses and 60 plasmids have been isolated. These archaeal viruses exhibit an exceptional diversity in morphology, with a wide array of shapes, such as spind......SUMMARY: Research on archaeal extrachromosomal genetic elements (ECEs) has progressed rapidly in the past decade. To date, over 60 archaeal viruses and 60 plasmids have been isolated. These archaeal viruses exhibit an exceptional diversity in morphology, with a wide array of shapes...... on archaeal ECEs has just started to unravel the molecular biology of these genetic entities and their interactions with archaeal hosts, it is expected to accelerate in the next decade....

  11. Nuclear fuel element

    Energy Technology Data Exchange (ETDEWEB)

    Armijo, J S; Coffing, L F

    1979-04-05

    The fuel element with circular cross-section for BWR and PWR consists of a core surrounded by a compound jacket container where there is a gap between the core and jacket during operation in the reactor. The core consists of U, Pu, Th compounds and mixtures of these. The compound jacket consists of zircaloy 2 or 4. In order to for example prevent the corrosion of the compound jacket, its inner surface has a metal barrier with smaller neutron absorbers than the jacket material in the form of a zirconium sponge. The zirconium of this metal barrier has impurities of various elements in the order of magnitude of 1000 to 5000 ppm. The oxygen content is in the range of 200 to 1200 ppm and the thickness of the metal barrier is 1-30% of the thickness of the jacket.

  12. Nuclear reactor fuel element

    International Nuclear Information System (INIS)

    D'Eye, R.W.M.; Shennan, J.V.; Ford, L.H.

    1977-01-01

    Fuel element with particles from ceramic fissionable material (e.g. uranium carbide), each one being coated with pyrolitically deposited carbon and all of them being connected at their points of contact by means of an individual crossbar. The crossbar consists of silicon carbide produced by reaction of silicon metal powder with the carbon under the influence of heat. Previously the silicon metal powder together with the particles was kneaded in a solvent and a binder (e.g. epoxy resin in methyl ethyl ketone plus setting agent) to from a pulp. The reaction temperature lies at 1750 0 C. The reaction itself may take place in a nitrogen atmosphere. There will be produced a fuel element with a high overall thermal conductivity. (DG) [de

  13. Nuclear fuel element

    International Nuclear Information System (INIS)

    1974-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed. A heat conducting fission product retaining metal liner of a refractory metal is incorporated in the fuel element between the cladding and the nuclear fuel to inhibit mechanical interaction between the nuclear fuel and the cladding, to isolate fission products and nuclear fuel impurities from contacting the cladding, and to improve the axial thermal peaking gradient along the length of the fuel rod. The metal liner can be in the form of a tube or hollow cylindrical column, a foil of single or multiple layers in the shape of a hollow cylindrical column, or a coating on the internal surface of the cladding. Preferred refractory metal materials are molybdenum, tungsten, rhenium, niobium and alloys of the foregoing metals

  14. Nuclear fuel element

    International Nuclear Information System (INIS)

    Thompson, J.R.; Rowland, T.C.

    1976-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed. A heat conducting, fission product retaining metal liner of a refractory metal is incorporated in the fuel element between the cladding and the nuclear fuel to inhibit mechanical interaction between the nuclear fuel and the cladding, to isolate fission products and nuclear fuel impurities from contacting the cladding and to improve the axial thermal peaking gradient along the length of the fuel rod. The metal liner can be in the form of a tube or hollow cylindrical column, a foil of single or multiple layers in the shape of a hollow cylindrical column, or a coating on the internal surface of the cladding. Preferred refractory metal materials are molybdenum, tungsten, rhenium, niobium and alloys of the foregoing metals

  15. Elements of quantum optics

    CERN Document Server

    Meystre, Pierre

    2007-01-01

    Elements of Quantum Optics gives a self-contained and broad coverage of the basic elements necessary to understand and carry out research in laser physics and quantum optics, including a review of basic quantum mechanics and pedagogical introductions to system-reservoir interactions and to second quantization. The text reveals the close connection between many seemingly unrelated topics, such as probe absorption, four-wave mixing, optical instabilities, resonance fluorescence and squeezing. It also comprises discussions of cavity quantum electrodynamics and atom optics. The 4th edition includes a new chapter on quantum entanglement and quantum information, as well as added discussions of the quantum beam splitter, electromagnetically induced transparency, slow light, and the input-output formalism needed to understand many problems in quantum optics. It also provides an expanded treatment of the minimum-coupling Hamiltonian and a simple derivation of the Gross-Pitaevskii equation, an important gateway to rese...

  16. Periodic table of elements

    International Nuclear Information System (INIS)

    Fluck, E.; Heumann, K.G.

    1985-01-01

    Following a recommendation by the International Union for Pure and Applied Chemistry (IUPAC), the groups of the periodic table shall be numbered from 1 to 18, instead of I to VIII as before. The recommendations has been approved of by the Committee on Nomenclature of the American Chemical Society. The new system abandons the distinction between main groups (a) and auxiliary groups (b), which in the past frequently has been the reason for misunderstandings between European and American chemists, due to different handling. The publishing house VCH Verlagsgesellschaft recently produced a new periodic table that shows the old and the new numbering system together at a glance, so that chemists will have time to get familiar with the new system. In addition the new periodic table represents an extensive data compilation arranged by elements. The front page lists the chemical properties of elements, the back page their physical properties. (orig./EF) [de

  17. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Kawada, Toshiyuki; Hirayama, Satoshi; Yoneya, Katsutoshi.

    1980-01-01

    Purpose: To enable load-depending operation as well as moderation for the restriction of operation conditions in the present nuclear reactors, by specifying the essential ingredients and the total weight of the additives to UO 2 fuel substances. Constitution: Two or more additives selected from Al 2 O 3 , B 2 O, CaO, MgO, SiO 2 , Na 2 O and P 2 O 5 are added by the total weight of 2 - 5% to fuel substances consisting of UO 2 or a mixture of UO 2 and PuO 2 . When the mixture is sintered, the strength of the fuel elements is decreased and the fuel-cladding interactions due to the difference in the heat expansion coefficients between the ceramic fuel elements and the metal claddings are decreased to a substantially harmless degree. (Horiuchi, T.)

  18. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Nakai, Keiichi

    1983-01-01

    Purpose: To decrease the tensile stresses resulted in a fuel can as well as prevent decladding of fuel pellets into the bore holes by decreasing the inner pressure within the nuclear fuel element. Constitution: A fuel can is filled with hollow fuel pellets, inserted with a spring for retaining the hollow fuel pellets with an appropriate force and, thereafter, closely sealed at the both ends with end plugs. A cylindrical body is disposed into the bore holes of the hollow fuel pellets. Since initial sealing gases and/or gaseous nuclear fission products can thus be excluded from the bore holes where the temperature is at the highest level, the inner pressure of the nuclear fuel element can be reduced to decrease the tensile strength resulted to the fuel can. Furthermore, decladding of fuel pellets into the bore holes can be prevented. (Moriyama, K.)

  19. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Ainsworth, K.F.

    1979-01-01

    A nuclear fuel element is described having a cluster of nuclear fuel pins supported in parallel, spaced apart relationship by transverse cellular braces within coaxial, inner and outer sleeves, the inner sleeve being in at least two separate axial lengths, each of the transverse braces having a peripheral portion which is clamped peripherally between the ends of the axial lengths of the inner sleeve. (author)

  20. Sensor for ionizable elements

    International Nuclear Information System (INIS)

    Berkey, E.; Reed, W.A. III; Hickam, W.M.

    1977-01-01

    Sensor to detect thermally ionizable elements or molucules in air, water vapour or oxygen or to be used as alkali leak detector in vacuum systems, e.g. in the pipe system of a liquid-metal cooled FBR. The sensor consists of an filament made of thorium-containing iridium as cathode with a temperature upto 1000 0 C and an anode sheet of molybdenum, nickel or stainless steal. (ORU) [de

  1. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Butterfield, C.E.; Waite, E.

    1982-01-01

    A nuclear reactor fuel element comprising a column of vibration compacted fuel which is retained in consolidated condition by a thimble shaped plug. The plug is wedged into gripping engagement with the wall of the sheath by a wedge. The wedge material has a lower coefficient of expansion than the sheath material so that at reactor operating temperature the retainer can relax sufficient to accommodate thermal expansion of the column of fuel. (author)

  2. OXIDATION OF TRANSURANIC ELEMENTS

    Science.gov (United States)

    Moore, R.L.

    1959-02-17

    A method is reported for oxidizing neptunium or plutonium in the presence of cerous values without also oxidizing the cerous values. The method consists in treating an aqueous 1N nitric acid solution, containing such cerous values together with the trivalent transuranic elements, with a quantity of hydrogen peroxide stoichiometrically sufficient to oxidize the transuranic values to the hexavalent state, and digesting the solution at room temperature.

  3. Transportation of radioactive elements

    International Nuclear Information System (INIS)

    Thubert, Francis; Rentien, Guy; Jacquet, Michel

    1981-01-01

    The production and marketing of artificial radioactive elements engaged in by the 'Office des Rayonnements Ionisants' requires the use of specially designed packagings and assorted means of transport. The authors begin by describing the different kinds of products involved and the forms of packagings needed, and go on to discuss the various means of transport used, underlining the fact that, in terms of number and gravity, the incidents that have occurred to date have indeed been few and far between [fr

  4. Vented nuclear fuel element

    International Nuclear Information System (INIS)

    Oguma, M.; Hirose, Y.

    1976-01-01

    A description is given of a vented nuclear fuel element having a plenum for accumulation of fission product gases and plug means for delaying the release of the fission product gases from the plenum, the plug means comprising a first porous body wettable with a liquid metal and a second porous body non-wettable with the liquid metal, the first porous body being impregnated with the liquid metal and in contact with the liquid metal

  5. Helium the disappearing element

    CERN Document Server

    Sears, Wheeler M

    2015-01-01

    The subject of the book is helium, the element, and its use in myriad applications including MRI machines, particle accelerators, space telescopes, and of course balloons and blimps. It was at the birth of our Universe, or the Big Bang, where the majority of cosmic helium was created; and stellar helium production continues. Although helium is the second most abundant element in the Universe, it is actually quite rare here on Earth and only exists because of radioactive elements deep within the Earth. This book includes a detailed history of the discovery of helium, of the commercial industry built around it, how the helium we actually encounter is produced within the Earth, and the state of the helium industry today. The gas that most people associate with birthday party balloons is running out. “Who cares?” you might ask. Well, without helium, MRI machines could not function, rockets could not go into space, particle accelerators such as those used by CERN could not operate, fiber optic cables would not...

  6. Elements of quantum information

    International Nuclear Information System (INIS)

    Schleich, W.P.

    2007-01-01

    Elements of Quantum Information introduces the reader to the fascinating field of quantum information processing, which lives on the interface between computer science, physics, mathematics, and engineering. This interdisciplinary branch of science thrives on the use of quantum mechanics as a resource for high potential modern applications. With its wide coverage of experiments, applications, and specialized topics - all written by renowned experts - Elements of Quantum Information provides and indispensable, up-to-date account of the state of the art of this rapidly advancing field and takes the reader straight up to the frontiers of current research. The articles have first appeared as a special issue of the journal 'Fortschritte der Physik / Progress of Physics'. Since then, they have been carefully updated. The book will be an inspiring source of information and insight for anyone researching and specializing in experiments and theory of quantum information. Topics addressed in Elements of Quantum Information include - Cavity Quantum Electrodynamics - Segmented Paul Traps - Cold Atoms and Bose-Einstein Condensates in Microtraps, Optical Lattices, and on Atom Chips - Rydberg Gases - Factorization of Numbers with Physical Systems - Entanglement of Continuous Variables - NMR and Solid State Quantum Computation - Quantum Algorithms and Quantum Machines - Complexity Theory - Quantum Crytography. (orig.)

  7. Using Finite Element Method

    Directory of Open Access Journals (Sweden)

    M.H.R. Ghoreishy

    2008-02-01

    Full Text Available This research work is devoted to the footprint analysis of a steel-belted radial tyre (185/65R14 under vertical static load using finite element method. Two models have been developed in which in the first model the tread patterns were replaced by simple ribs while the second model was consisted of details of the tread blocks. Linear elastic and hyper elastic (Arruda-Boyce material models were selected to describe the mechanical behavior of the reinforcing and rubbery parts, respectively. The above two finite element models of the tyre were analyzed under inflation pressure and vertical static loads. The second model (with detailed tread patterns was analyzed with and without friction effect between tread and contact surfaces. In every stage of the analysis, the results were compared with the experimental data to confirm the accuracy and applicability of the model. Results showed that neglecting the tread pattern design not only reduces the computational cost and effort but also the differences between computed deformations do not show significant changes. However, more complicated variables such as shape and area of the footprint zone and contact pressure are affected considerably by the finite element model selected for the tread blocks. In addition, inclusion of friction even in static state changes these variables significantly.

  8. Study of Superheavy Elements

    International Nuclear Information System (INIS)

    Hofmann, Sigurd

    2007-01-01

    The nuclear shell model predicts that the next doubly magic shell-closure beyond 208 Pb is at a proton number Z = 114, 120, or 126 and at a neutron number N = 172 or 184. The outstanding aim of experimental investigations is the exploration of this region of spherical 'SuperHeavy Elements' (SHEs). Experimental methods are described, which allowed for the identification of elements produced on a cross-section level of about 1 pb. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission, not fission. Decay properties as well as reaction cross-sections are compared with results of theoretical investigations. Finally, plans are presented for the further development of the experimental set-up and the application of new techniques, as for instance the precise mass measurement of the produced nuclei using ion traps. At increased sensitivity, the detailed exploration of the region of spherical SHEs will start, after first steps on the island were made in recent years. (Author)

  9. Probabilistic finite elements

    Science.gov (United States)

    Belytschko, Ted; Wing, Kam Liu

    1987-01-01

    In the Probabilistic Finite Element Method (PFEM), finite element methods have been efficiently combined with second-order perturbation techniques to provide an effective method for informing the designer of the range of response which is likely in a given problem. The designer must provide as input the statistical character of the input variables, such as yield strength, load magnitude, and Young's modulus, by specifying their mean values and their variances. The output then consists of the mean response and the variance in the response. Thus the designer is given a much broader picture of the predicted performance than with simply a single response curve. These methods are applicable to a wide class of problems, provided that the scale of randomness is not too large and the probabilistic density functions possess decaying tails. By incorporating the computational techniques we have developed in the past 3 years for efficiency, the probabilistic finite element methods are capable of handling large systems with many sources of uncertainties. Sample results for an elastic-plastic ten-bar structure and an elastic-plastic plane continuum with a circular hole subject to cyclic loadings with the yield stress on the random field are given.

  10. Do superheavy elements imply the existence of black holes

    International Nuclear Information System (INIS)

    Pringle, J.E.; Dearborn, D.S.P.; Fabian, A.C.

    1976-01-01

    Some comments are offered on the question of where superheavy elements, such as elements 116, 124 and 126, are likely to have been formed. Most of these elements are thought to have been produced under conditions of explosive nucleosynthesis by what is known as the 'r-process', and particularly in conventional supernova explosions, but it is stated that the ability of the r-process to produce superheavy elements is very uncertain, and the conditions necessary for synthesis of these elements are difficult to realise in astrophysical situations. It is thought that superheavy elements exist in the outer layers of neutron stars, and ideal conditions for the production of superheavy nuclei, such as high neutron flux and rapid β decays, occur in the disruption of a neutron star. Such disruption is possible in two ways, both of which involve a black hole. It is likely that a neutron star is disrupted when it accretes sufficient material for its mass to exceed the maximum mass for stability, and it then has no alternative but to collapse to form a black hole and it seems possible that some of the outer layers are thrown off during the process. It is thus argued that the most likely site for the production of superheavy elements is in the surface layers of a neutron star, and the most plausible means by which these layers can be returned to the interstellar medium involves the intervention or formation of a black hole. (U.K.)

  11. Method and apparatus for producing synthesis gas

    Science.gov (United States)

    Hemmings, John William; Bonnell, Leo; Robinson, Earl T.

    2010-03-03

    A method and apparatus for reacting a hydrocarbon containing feed stream by steam methane reforming reactions to form a synthesis gas. The hydrocarbon containing feed is reacted within a reactor having stages in which the final stage from which a synthesis gas is discharged incorporates expensive high temperature materials such as oxide dispersed strengthened metals while upstream stages operate at a lower temperature allowing the use of more conventional high temperature alloys. Each of the reactor stages incorporate reactor elements having one or more separation zones to separate oxygen from an oxygen containing feed to support combustion of a fuel within adjacent combustion zones, thereby to generate heat to support the endothermic steam methane reforming reactions.

  12. Gas Phase Nanoparticle Synthesis

    Science.gov (United States)

    Granqvist, Claes; Kish, Laszlo; Marlow, William

    This book deals with gas-phase nanoparticle synthesis and is intended for researchers and research students in nanomaterials science and engineering, condensed matter physics and chemistry, and aerosol science. Gas-phase nanoparticle synthesis is instrumental to nanotechnology - a field in current focus that raises hopes for environmentally benign, resource-lean manufacturing. Nanoparticles can be produced by many physical, chemical, and even biological routes. Gas-phase synthesis is particularly interesting since one can achieve accurate manufacturing control and hence industrial viability.

  13. Radiation chemical synthesis

    International Nuclear Information System (INIS)

    Zagoretz, P.A.; Poluetkov, V.A.; Shostenko, A.G.

    1986-01-01

    The authors consider processes in radiation chemical synthesis which are being developed in various scientific-research organizations. The important advantages of radiation chlorination, viz. the lower temperature compared with the thermal method and the absence of dehydrochlorination products are discussed. The authors examine the liquid-phase chlorination of trifluorochloroethyltrichloromethyl ether to obtain the pentachloro-contining ether, trifluorodichloroethyltrichloromethyl ether. The authors discuss radiation synthesis processes that have be used formulated kinetic equations on which models have been based. It is concluded that the possibilities of preparative (micro- and low-tonnage) radiation synthesis are promising

  14. Elements of social action

    Directory of Open Access Journals (Sweden)

    Marjanović Miloš

    2011-01-01

    Full Text Available Because of the significant analytical advantages, the author prefers social action as initial sociological concept in the relation to social phenomenon. Its basic elements are: actors, subjects and tools, needs and interests, values and norms, positions and roles. Actors set in motion and unify the rest of elements, guide to the magic triangle of sociology (movement, change, order, reaffirm actor paradigm to systemic paradigm. Subjects and tools materialize an action and its overestimate results in technological determinism or (by means of property as institutional appropriation of nature in the (unclassed historical type of society. Needs and interests are the basis of person's motivation and starting point for depth analysis of sociability. The expansion of legitimate interests circle develops techniques of normative regulation. Values and norms guide to institutional-organizational, positions to vertical and roles to horizontal structure. Values give the meaning to the action as well as to human existence, they are orientations of motivate system of personality but also basic aspect of society. As abstractions, values are latent background of norms and they tell to us what to do, and norms how to do something. Norms are specified instructions for suitable behavior Without normative order, not to be possible the satisfying of needs and the conciliation of interests. Riches, power and prestige are components of social position, and legal status is the determination of rights and obligations of the position. Roles are normative expectation of behavior. Toward kinds of sanctions roles are classified. Roles but also other elements of social action are starting point for sociological analysis of legal norms and institutes. On the other side, the observation of legal component of social actions enriches, strengths and precises sociological analysis of them.

  15. Analytical elements of mechanics

    CERN Document Server

    Kane, Thomas R

    2013-01-01

    Analytical Elements of Mechanics, Volume 1, is the first of two volumes intended for use in courses in classical mechanics. The books aim to provide students and teachers with a text consistent in content and format with the author's ideas regarding the subject matter and teaching of mechanics, and to disseminate these ideas. The book opens with a detailed exposition of vector algebra, and no prior knowledge of this subject is required. This is followed by a chapter on the topic of mass centers, which is presented as a logical extension of concepts introduced in connection with centroids. A

  16. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    Klepfer, H.H.

    1974-01-01

    A nuclear fuel element is described which comprises: 1) an elongated clad container, 2) a layer of high lubricity material being disposed in and adjacent to the clad container, 3) a low neutron capture cross section metal liner being disposed in the clad container and adjacent to the layer, 4) a central core of a body of nuclear fuel material disposed in and partially filling the container and forming an internal cavity in the container, 5) an enclosure integrally secured and sealed at each end of the container, and a nuclear fuel material retaining means positioned in the cavity. (author)

  17. Elements of real analysis

    CERN Document Server

    Sprecher, David A

    2010-01-01

    This classic text in introductory analysis delineates and explores the intermediate steps between the basics of calculus and the ultimate stage of mathematics: abstraction and generalization.Since many abstractions and generalizations originate with the real line, the author has made it the unifying theme of the text, constructing the real number system from the point of view of a Cauchy sequence (a step which Dr. Sprecher feels is essential to learn what the real number system is).The material covered in Elements of Real Analysis should be accessible to those who have completed a course in

  18. Nuclear reactor fuel elements

    International Nuclear Information System (INIS)

    Hindle, E. D.

    1984-01-01

    An array of rods is assembled to form a fuel element for a pressurized water reactor, the rods comprising zirconium alloy sheathed nuclear fuel pellets and containing helium. The helium gas pressure is selected for each rod so that it differs substantially from the helium gas pressure in its closest neighbors. In a preferred arrangement the rods are arranged in a square lattice and the helium gas pressure alternates between a relatively high value and a relatively low value so that each rod has as its closest neighbors up to four rods containing helium gas at the other pressure value

  19. Nuclear reactor fuel elements

    Energy Technology Data Exchange (ETDEWEB)

    Hindle, E. D.

    1984-10-16

    An array of rods is assembled to form a fuel element for a pressurized water reactor, the rods comprising zirconium alloy sheathed nuclear fuel pellets and containing helium. The helium gas pressure is selected for each rod so that it differs substantially from the helium gas pressure in its closest neighbors. In a preferred arrangement the rods are arranged in a square lattice and the helium gas pressure alternates between a relatively high value and a relatively low value so that each rod has as its closest neighbors up to four rods containing helium gas at the other pressure value.

  20. Osteoporosis and trace elements

    DEFF Research Database (Denmark)

    Aaseth, J.; Boivin, G.; Andersen, Ole

    2012-01-01

    More than 200 million people are affected by osteoporosis worldwide, as estimated by 2 million annual hip fractures and other debilitating bone fractures (vertebrae compression and Colles' fractures). Osteoporosis is a multi-factorial disease with potential contributions from genetic, endocrine...... in new bone and results in a net gain in bone mass, but may be associated with a tissue of poor quality. Aluminum induces impairment of bone formation. Gallium and cadmium suppresses bone turnover. However, exact involvements of the trace elements in osteoporosis have not yet been fully clarified...

  1. [Healthcare marketing elements].

    Science.gov (United States)

    Ameri, Cinzia; Fiorini, Fulvio

    2014-01-01

    Marketing puts its foundation on a few key concepts: need-demand, product-service, satisfaction, exchange, market, or business structure manufacturing / supply. The combination of these elements allows you to build an effective marketing strategy. Crucial in this respect is to remember the Porter matrix, which shows that for a correct analysis of the relevant market is necessary to refer to the "five forces at play", ie: customers, competitors, new entrants and substitutes threat. Another key lever for proper marketing oriented approach is the continuous and constant monitoring of the application, anticipating their dissatisfactions.

  2. Technical Elements (CCT1)

    DEFF Research Database (Denmark)

    Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

    2017-01-01

    Many of the aspects dealt with in the CA EPBD are closely interlinked with each other and may refer to both new and existing buildings, as well as to inspection and certification. This is also true for technical aspects, such as the calculation methodologies, and how to include technical systems......’ efficiency or how to integrate renewable energy within them. The central team for Technical Elements deals with issues of a technical nature, which are common to new and existing buildings, and/or with minimum demands, certification and inspection. This report focuses on the implementation of Articles 3, 4...

  3. Optical Finite Element Processor

    Science.gov (United States)

    Casasent, David; Taylor, Bradley K.

    1986-01-01

    A new high-accuracy optical linear algebra processor (OLAP) with many advantageous features is described. It achieves floating point accuracy, handles bipolar data by sign-magnitude representation, performs LU decomposition using only one channel, easily partitions and considers data flow. A new application (finite element (FE) structural analysis) for OLAPs is introduced and the results of a case study presented. Error sources in encoded OLAPs are addressed for the first time. Their modeling and simulation are discussed and quantitative data are presented. Dominant error sources and the effects of composite error sources are analyzed.

  4. Elements of energy conversion

    CERN Document Server

    Russell, Charles R

    2013-01-01

    Elements of Energy Conversion brings together scattered information on the subject of energy conversion and presents it in terms of the fundamental thermodynamics that apply to energy conversion by any process. Emphasis is given to the development of the theory of heat engines because these are and will remain most important power sources. Descriptive material is then presented to provide elementary information on all important energy conversion devices. The book contains 10 chapters and opens with a discussion of forms of energy, energy sources and storage, and energy conversion. This is foll

  5. Synthesis of Zirconium Lower Chlorides

    International Nuclear Information System (INIS)

    Gaviria, Juan P.

    2002-01-01

    This research is accurately related to the Halox concept of research reactor spent fuel element treatment.The aim of this project is to work the conditioning through selected chlorination of the element that make the spent fuel element. This research studied the physical chemistry conditions which produce formation of the lower zirconium chlorides through the reaction between metallic Zr and gaseous ZrCl 4 in a silica reactor.This work focused special attention in the analysis and confrontation of the published results among the different authors in order to reveal coincidences and contradictions.Experimental section consisted in a set of synthesis with different reaction conditions and reactor design. After reaction were analyzed the products on Zr shavings and the deposit growth on wall reactor.The products were strongly dependent of reactor design. It was observed that as the distance between Zr and wall reactor increased greater was tendency to lower chlorides formation.In reactors with small distance the reaction follows other way without formation of lower chlorides.Analysis on deposit growth on reactor showed that may be formed to a mixture of Si x Zr y intermetallics and zirconium oxides.Presence of oxygen in Zr and Zr-Si compounds on wall reactor reveals that there is an interaction between quartz and reactants.This interaction is in gaseous phase because contamination is observed in experiences where Zr was not in contact with reactor.Finally, it was made a global analysis of all experiences and a possible mechanism that interprets reaction ways is proposed

  6. Synthesis of Acetylhomoagmatine

    Directory of Open Access Journals (Sweden)

    Carmenza Duque

    2006-08-01

    Full Text Available Abstract: The first total synthesis of acetylhomoagmatine, a natural product isolated form the methanolic extracts from the sponge Cliona celata, is performed in four steps in a very high yield.

  7. 2002 Annual report: synthesis

    International Nuclear Information System (INIS)

    2003-01-01

    This synthesis of the Annual Report 2002 presents information of the main activities on the scope of the radiation protection and nuclear safety of the Nuclear Regulatory Authority (ARN) of the Argentina during 2002

  8. Principles of asymmetric synthesis

    CERN Document Server

    Gawley, Robert E; Aube, Jeffrey

    2012-01-01

    The world is chiral. Most of the molecules in it are chiral, and asymmetric synthesis is an important means by which enantiopure chiral molecules may be obtained for study and sale. Using examples from the literature of asymmetric synthesis, this book presents a detailed analysis of the factors that govern stereoselectivity in organic reactions. After an explanation of the basic physical-organic principles governing stereoselective reactions, the authors provide a detailed, annotated glossary of stereochemical terms. A chapter on "Practical Aspects of Asymmetric Synthesis" provides a critical overview of the most common methods for the preparation of enantiomerically pure compounds, techniques for analysis of stereoisomers using chromatographic, spectroscopic, and chiroptical methods. The authors then present an overview of the most important methods in contemporary asymmetric synthesis organized by reaction type. Thus, there are four chapters on carbon-carbon bond forming reactions, one chapter on reductions...

  9. Synthesis of protargol

    International Nuclear Information System (INIS)

    Baratova, Z.R.; Sattarova, M.A.; Abdurakhmanov, A.Kh.; Solojenkin, P.M.

    1997-01-01

    This paper is devoted to synthesis of protargol containing 7,5-8,3% of silver. The flowsheet of obtaining of protargol was elaborated. The obtained protargol contains 7,5% of silver, insoluble in alcohol, ether and chloroform.

  10. Synthesis Polarimetry Calibration

    Science.gov (United States)

    Moellenbrock, George

    2017-10-01

    Synthesis instrumental polarization calibration fundamentals for both linear (ALMA) and circular (EVLA) feed bases are reviewed, with special attention to the calibration heuristics supported in CASA. Practical problems affecting modern instruments are also discussed.

  11. SYNTHESIS, CHARACTERIZATION AND PHOTOCATALYTIC ...

    African Journals Online (AJOL)

    ISSN 1011-3924. © 2018 Chemical Society of Ethiopia and The Authors. Printed in Ethiopia ... SYNTHESIS, CHARACTERIZATION AND PHOTOCATALYTIC ACTIVITY OF .... cm−1 to determine the surface functional groups. 10 mg of sample ...

  12. 2000 Annual report: synthesis

    International Nuclear Information System (INIS)

    2001-01-01

    This synthesis of the Annual Report 2000 present information of the main activities on the scope of the radiation protection and nuclear safety of the Nuclear Regulatory Authority (NRA) of the Argentina during 2000

  13. 2001 Annual report: synthesis

    International Nuclear Information System (INIS)

    2001-01-01

    This synthesis of the Annual Report 2001 presents information of the main activities on the scope of the radiation protection and nuclear safety of the Nuclear Regulatory Authority (ARN) of the Argentina during 2001

  14. Nuclear fuel element

    International Nuclear Information System (INIS)

    Iwano, Yoshihiko.

    1993-01-01

    Microfine cracks having a depth of less than 10% of a pipe thickness are disposed radially from a central axis each at an interval of less than 100 micron over the entire inner circumferential surface of a zirconium alloy fuel cladding tube. For manufacturing such a nuclear fuel element, the inside of the cladding tube is at first filled with an electrolyte solution of potassium chloride. Then, electrolysis is conducted using the cladding tube as an anode and the electrolyte solution as a cathode, and the inner surface of the cladding tube with a zirconium dioxide layer having a predetermined thickness. Subsequently, the cladding tube is laid on a smooth steel plate and lightly compressed by other smooth steel plate to form microfine cracks in the zirconium dioxide layer on the inner surface of the cladding tube. Such a compressing operation is continuously applied to the cladding tube while rotating the cladding tube. This can inhibit progress of cracks on the inner surface of the cladding tube, thereby enabling to prevent failure of the cladding tube even if a pellet/cladding tube mechanical interaction is applied. Accordingly, reliability of the nuclear fuel elements is improved. (I.N.)

  15. Heavy-element nucleosynthesis

    International Nuclear Information System (INIS)

    Mathews, G.J.

    1990-01-01

    New measurements and theoretical studies of nuclear properties, together with new astronomical data on the growth of heavy-element abundances during the early history of the Galaxy, now provide a clearer picture of where in nature the elements heavier than iron are produced by rapid (r-process) and show (s-process) neutron capture reactions. The nuclear data suggest that the r-process involves a high-neutron-density beta-flow equilibrium environment and that the s-process may have occurred at a temperature and neutron density consistent with a 13 C(α,n) 16 0 neutron source. The astronomical data, when compared with simple galactic chemical evolution modes, suggests that the r-process is associated with type II supernovae and that the neutron source must be manufactured by the star. Low-mass type II supernovae are proposed as the most important contributors to the r-process. A 13 C neutron source in intermediate-mass stars is proposed for the s-process. 64 refs., 7 figs

  16. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    1980-01-01

    The invention is of a nuclear fuel element which comprises a central core of a body of nuclear fuel material selected from the group consisting of compounds of uranium, plutonium, thorium and mixtures thereof, and an elongated composite cladding container comprising a zirconium alloy tube containing constituents other than zirconium in an amount greater than about 5000 parts per million by weight and an undeformed metal barrier of moderate purity zirconium bonded to the inside surface of the alloy tube. The container encloses the core so as to leave a gap between the container and the core during use in a nuclear reactor. The metal barrier is of moderate purity zirconium with an impurity level on a weight basis of at least 1000ppm and less than 5000ppm. Impurity levels of specific elements are given. Variations of the invention are also specified. The composite cladding reduces chemical interaction, minimizes localized stress and strain corrosion and reduces the likelihood of a splitting failure in the zirconium alloy tube. Other benefits are claimed. (U.K.)

  17. Two-directional synthesis as a tool for diversity-oriented synthesis: Synthesis of alkaloid scaffolds

    Directory of Open Access Journals (Sweden)

    Kieron M. G. O’Connell

    2012-06-01

    Full Text Available Two-directional synthesis represents an ideal strategy for the rapid elaboration of simple starting materials and their subsequent transformation into complex molecular architectures. As such, it is becoming recognised as an enabling technology for diversity-oriented synthesis. Herein, we provide a thorough account of our work combining two-directional synthesis with diversity-oriented synthesis, with particular reference to the synthesis of polycyclic alkaloid scaffolds.

  18. Quasifission Dynamics in the Formation of Superheavy Elements

    Directory of Open Access Journals (Sweden)

    Hinde D.J.

    2017-01-01

    Full Text Available Superheavy elements are created through the fusion of two heavy nuclei. The large Coulomb energy that makes superheavy elements unstable also makes fusion forming a compact compound nucleus very unlikely. Instead, after sticking together for a short time, the two nuclei usually come apart, in a process called quasifission. Mass-angle distributions give the most direct information on the characteristics and time scales of quasifission. A systematic study of carefully chosen mass-angle distributions has provided information on the global trends of quasifission. Large deviations from these systematics at beam energies near the capture barrier reveal the major role played by the nuclear structure of the two colliding nuclei in determining the reaction outcome, and thus implicitly in hindering or favouring superheavy element synthesis.

  19. Instrument Modeling and Synthesis

    Science.gov (United States)

    Horner, Andrew B.; Beauchamp, James W.

    During the 1970s and 1980s, before synthesizers based on direct sampling of musical sounds became popular, replicating musical instruments using frequency modulation (FM) or wavetable synthesis was one of the “holy grails” of music synthesis. Synthesizers such as the Yamaha DX7 allowed users great flexibility in mixing and matching sounds, but were notoriously difficult to coerce into producing sounds like those of a given instrument. Instrument design wizards practiced the mysteries of FM instrument design.

  20. Nitrocyclopropanes: synthesis and properties

    Energy Technology Data Exchange (ETDEWEB)

    Averina, Elena B; Yashin, N V; Kuznetsova, Tamara S; Zefirov, Nikolai S [Department of Chemistry, M.V. Lomonosov Moscow State University, Moscow (Russian Federation)

    2009-10-31

    State-of-the-art data on the methods of synthesis, properties and transformations of nitro- and- dinitrocyclopropanes of different structure is generalized and described systematically. The attention is focused on stereoselective cyclopropanation methods, new approaches to the synthesis of natural products and their synthetic analogues with diversified biological activities, in particular, of aminocyclopropane acids based on nitrocyclopropanes, and the formation of structures of energetic compounds.

  1. NIH Common Data Elements Repository

    Data.gov (United States)

    U.S. Department of Health & Human Services — The NIH Common Data Elements (CDE) Repository has been designed to provide access to structured human and machine-readable definitions of data elements that have...

  2. The CP molecule labyrinth: a paradigm of how endeavors in total synthesis lead to discoveries and inventions in organic synthesis.

    Science.gov (United States)

    Nicolaou, K C; Baran, Phil S

    2002-08-02

    Imagine an artist carving a sculpture from a marble slab and finding gold nuggets in the process. This thought is not a far-fetched description of the work of a synthetic chemist pursuing the total synthesis of a natural product. At the end of the day, he or she will be judged by the artistry of the final work and the weight of the gold discovered in the process. However, as colorful as this description of total synthesis may be, it does not entirely capture the essence of the endeavor, for there is much more to be told, especially with regard to the contrast of frustrating failures and exhilarating moments of discovery. To fully appreciate the often Herculean nature of the task and the rewards that accompany it, one must sense the details of the enterprise behind the scenes. A more vivid description of total synthesis as a struggle against a tough opponent is perhaps appropriate to dramatize these elements of the experience. In this article we describe one such endeavor of total synthesis which, in addition to reaching the target molecule, resulted in a wealth of new synthetic strategies and technologies for chemical synthesis. The total synthesis of the CP molecules is compared to Theseus' most celebrated athlos (Greek for exploit, accomplishment): the conquest of the dreaded Minotaur, which he accomplished through brilliance, skill, and bravery having traversed the famous labyrinth with the help of Ariadne. This story from Greek mythology comes alive in modern synthetic expeditions toward natural products as exemplified by the total synthesis of the CP molecules which serve as a paradigm for modern total synthesis endeavors, where the objectives are discovery and invention in the broader sense of organic synthesis.

  3. Joining elements of silicon carbide

    International Nuclear Information System (INIS)

    Olson, B.A.

    1979-01-01

    A method of joining together at least two silicon carbide elements (e.g.in forming a heat exchanger) is described, comprising subjecting to sufficiently non-oxidizing atmosphere and sufficiently high temperature, material placed in space between the elements. The material consists of silicon carbide particles, carbon and/or a precursor of carbon, and silicon, such that it forms a joint joining together at least two silicon carbide elements. At least one of the elements may contain silicon. (author)

  4. Catalysts for the reduction of SO{sub 2} to elemental sulfur

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Y.; Yu, Q.Q.; Chang, S.G. [Lawrence Berkeley Lab., Berkeley, CA (United States)

    1995-11-01

    Catalysts have been prepared for the reduction of SO{sub 2} to elemental sulfur by synthesis gas. A catalyst allows to obtain more than 97% yield of elemental sulfur with a single-stage reactor at 540{degrees}C. A lifetime test has been successfully performed. The mass balance of sulfur and carbon has been checked. The effect of H{sub 2}S, COS, and H{sub 2}O has been studied.

  5. Trace element emissions from coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    Trace elements are emitted during coal combustion. The quantity, in general, depends on the physical and chemical properties of the element itself, the concentration of the element in the coal, the combustion conditions and the type of particulate control device used, and its collection efficiency as a function of particle size. Some trace elements become concentrated in certain particle streams following combustion such as bottom ash, fly ash, and flue gas particulate matter, while others do not. Various classification schemes have been developed to describe this partitioning behaviour. These classification schemes generally distinguish between: Class 1: elements that are approximately equally concentrated in the fly ash and bottom ash, or show little or no fine particle enrichment, examples include Mn, Be, Co and Cr; Class 2: elements that are enriched in the fly ash relative to bottom ash, or show increasing enrichment with decreasing particle size, examples include As, Cd, Pb and Sb; Class 3: elements which are emitted in the gas phase (primarily Hg (not discussed in this review), and in some cases, Se). Control of class 1 trace elements is directly related to control of total particulate matter emissions, while control of the class 2 elements depends on collection of fine particulates. Due to the variability in particulate control device efficiencies, emission rates of these elements can vary substantially. The volatility of class 3 elements means that particulate controls have only a limited impact on the emissions of these elements.

  6. REACTOR FUEL ELEMENTS TESTING CONTAINER

    Science.gov (United States)

    Whitham, G.K.; Smith, R.R.

    1963-01-15

    This patent shows a method for detecting leaks in jacketed fuel elements. The element is placed in a sealed tank within a nuclear reactor, and, while the reactor operates, the element is sparged with gas. The gas is then led outside the reactor and monitored for radioactive Xe or Kr. (AEC)

  7. Accelerator vacuum system elements

    International Nuclear Information System (INIS)

    Sivokon', V.V.; Kobets, A.F.; Shvetsov, V.A.; Sivokon', L.V.

    1980-01-01

    Some elements of vacuum systems are investigated. Considerable attention has been given to the investigation into peculiarities in pumping out of a ionoguide for transportation of an accelerated charged particles beam the spread of which often attains a considerable length. The number of pumps over the ionoguide length is experimentally determined. It is shown that as a result of ionoguide warm-up the pumping out time is considerably reduced maximum permissible pressure is decreased by two orders and lesser rate of pump pumping out is required. The investigations have shown that when operating the ionoguide there is no necessity in setting up seals between the ionoguide and magnetodischarged pump. The causes of the phenomenon in which the pressure near the pump is greater than in the end of the ionoguide, are impurities carried in by the pump into the ionoguide volume and the pumping out capacity of the pressure converter

  8. Ucla, escuela elemental

    Directory of Open Access Journals (Sweden)

    Neutra, Richard J.

    1962-03-01

    Full Text Available La Escuela Elemental de Preparación de la Universidad de California, en Los Angeles, está dedicada a la educación e investigación y preparación del profesorado de la infancia. Se ha construido en un paraje maravilloso, de frondosa vegetación, frente a un terreno bastante quebrado, circunstancia que presta mayor encanto al conjunto, construido con gran pericia y adaptación al paisaje a base de una dominante horizontalidad, con materiales sencillos (ladrillos, hierro y madera y gran comunicación con la naturaleza mediante grandes cristaleras correderas que ensanchan las clases y las suplementan hacia el jardín de acuerdo con las nuevas normas y prácticas docentes.

  9. Improved nuclear fuel element

    International Nuclear Information System (INIS)

    1974-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed and has a metal liner disposed between the cladding and the nuclear fuel material and a high lubricity material in the form of a coating disposed between the liner and the cladding. The liner preferably has a thickness greater than the longest fission product recoil distance and is composed of a low neutron capture cross-section material. The liner is preferably composed of zirconium, an alloy of zirconium, niobium or an alloy of niobium. The liner serves as a preferential reaction site for volatile impurities and fission products and protects the cladding from contact and reaction with such impurities and fission products. The high lubricity material acts as an interface between the liner and the cladding and reduces localized stresses on the cladding due to fuel expansion and cracking of the fuel

  10. Probabilistic fracture finite elements

    Science.gov (United States)

    Liu, W. K.; Belytschko, T.; Lua, Y. J.

    1991-05-01

    The Probabilistic Fracture Mechanics (PFM) is a promising method for estimating the fatigue life and inspection cycles for mechanical and structural components. The Probability Finite Element Method (PFEM), which is based on second moment analysis, has proved to be a promising, practical approach to handle problems with uncertainties. As the PFEM provides a powerful computational tool to determine first and second moment of random parameters, the second moment reliability method can be easily combined with PFEM to obtain measures of the reliability of the structural system. The method is also being applied to fatigue crack growth. Uncertainties in the material properties of advanced materials such as polycrystalline alloys, ceramics, and composites are commonly observed from experimental tests. This is mainly attributed to intrinsic microcracks, which are randomly distributed as a result of the applied load and the residual stress.

  11. Nuclear fuel elements

    International Nuclear Information System (INIS)

    Obara, Hiroshi.

    1981-01-01

    Purpose: To suppress iodine release thereby prevent stress corrosion cracks in fuel cans by dispersing ferrous oxide at the outer periphery of sintered uranium dioxide pellets filled and sealed within zirconium alloy fuel cans of fuel elements. Constitution: Sintered uranium dioxide pellets to be filled and sealed within a zirconium alloy fuel can are prepared either by mixing ferric oxide powder in uranium dioxide powder, sintering and then reducing at low temperature or by mixing iron powder in uranium dioxide powder, sintering and then oxidizing at low temperature. In this way, ferrous oxide is dispersed on the outer periphery of the sintered uranium dioxide pellets to convert corrosive fission products iodine into iron iodide, whereby the iodine release is suppressed and the stress corrosion cracks can be prevented in the fuel can. (Moriyama, K.)

  12. Nuclear fuel element

    International Nuclear Information System (INIS)

    Hirama, H.

    1978-01-01

    A nuclear fuel element comprises an elongated tube having upper and lower end plugs fixed to both ends thereof and nuclear fuel pellets contained within the tube. The fuel pellets are held against the lower end plug by a spring which is supported by a setting structure. The setting structure is maintained at a proper position at the middle of the tube by a wedge effect caused by spring force exerted by the spring against a set of balls coacting with a tapered member of the setting structure thereby wedging the balls against the inner wall of the tube, and the setting structure is moved free by pushing with a push bar against the spring force so as to release the wedge effect

  13. Finite element modelling

    International Nuclear Information System (INIS)

    Tonks, M.R.; Williamson, R.; Masson, R.

    2015-01-01

    The Finite Element Method (FEM) is a numerical technique for finding approximate solutions to boundary value problems. While FEM is commonly used to solve solid mechanics equations, it can be applied to a large range of BVPs from many different fields. FEM has been used for reactor fuels modelling for many years. It is most often used for fuel performance modelling at the pellet and pin scale, however, it has also been used to investigate properties of the fuel material, such as thermal conductivity and fission gas release. Recently, the United Stated Department Nuclear Energy Advanced Modelling and Simulation Program has begun using FEM as the basis of the MOOSE-BISON-MARMOT Project that is developing a multi-dimensional, multi-physics fuel performance capability that is massively parallel and will use multi-scale material models to provide a truly predictive modelling capability. (authors)

  14. Heavy-element research

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    The status is reported of studies on the solid-state chemistry of the actinides and lanthanides, spectroscopy of actinide compounds, and dynamic chemical description of actinide elements in solution. Phase studies were done on Rb 2 UO 4 , K 2 UO 4 , Li 2 UO 4 , and Es 2 U 2 O 7 . The lithium neptunate (VI) system was investigated and the existence of Li 2 NpO 4 was established. In oxidation-reduction studies it was shown that Am(III) can be electrolytically oxidized to Am(IV) in strong H 3 PO 4 , but Cf(III) and Pr(III) do not oxidize. The low-temperature absorption spectrum of thin films of NpBr 3 was investigated. (U.S.)

  15. ELEMENTAL FORMS OF HOSPITALITY

    Directory of Open Access Journals (Sweden)

    Maximiliano Emanuel Korstanje

    2010-11-01

    Full Text Available Modern studies emphasized on the needs of researching the hospitality as relevant aspects of tourism and hospitality fields. Anyway, these approaches are inextricably intertwined to the industry of tourism and do not take seriously the anthropological and sociological roots of hospitality. In fact, the hotel seems to be a partial sphere of hospitality at all. Under this context, the present paper explores the issue of hospitality enrooted in the political and economic indo-European principle of free-transit which is associated to a much broader origin.  Starting from the premise etymologically hostel and hospital share similar origins, we follow the contributions of J Derrida to determine the elements that formed the hospitality up to date.

  16. Photo-switching element

    Energy Technology Data Exchange (ETDEWEB)

    Masaki, Yuichi

    1987-10-31

    Photo-input MOS transistor (Photo-switching element) cannot give enough ON/OFF ratio but requires an auxiliary condenser for a certain type of application. In addition, PN junction of amorphous silicon is not practical because it gives high leak current resulting in low electromotive force. In this invention, a solar cell was constructed with a lower electrode consisting of a transparent electro-conducting film, a photosensitive part consisting of an amorphous Si layer of p-i-n layer construction, and an upper metal electrode consisting of Cr or Nichrome, and a thin film transistor was placed on the solar cell, and further the upper metal electrode was co-used as a gate electrode of the thin film transistor; this set-up of this invention enabled to attain an efficient photo-electric conversion of the incident light, high electromotive force of the solar cell, and the transistor with high ON/OFF ratio. (3 figs)

  17. An Efficient Catalyst for the Synthesis of Schiff Bases

    International Nuclear Information System (INIS)

    Fareed, G.; Afza, N.; Kalhoro, M.A.

    2013-01-01

    An efficient high yielding synthesis of Schiff bases (1-17) is derived from condensation of 2-fluorenamine and 4-amino phenol with a variety of aldehydes catalyzed by dodecatungstosilicic acid P/sub 2/O/sub 5/ under solvent free conditions at room temperature. The catayst is found to be more efficient in terms of ease of reaction workup and high yields. This methodology contributes to an energy efficient, facile and environamental friendly synthesis for the preparation of Schiff bases. The structures of afforded Schiff bases were characterized by spectroscopic data and elemental analysis. (author)

  18. An Approach to Interface Synthesis

    DEFF Research Database (Denmark)

    Madsen, Jan; Hald, Bjarne

    1995-01-01

    Presents a novel interface synthesis approach based on a one-sided interface description. Whereas most other approaches consider interface synthesis as optimizing a channel to existing client/server modules, we consider the interface synthesis as part of the client/server module synthesis (which...... may contain the re-use of existing modules). The interface synthesis approach describes the basic transformations needed to transform the server interface description into an interface description on the client side of the communication medium. The synthesis approach is illustrated through a point...

  19. Origin and Evolution of the Elements

    Science.gov (United States)

    McWilliam, Andrew; Rauch, Michael

    2004-09-01

    Introduction; List of participants; 1. Mount Wilson Observatory contributions to the study of cosmic abundances of the chemical elements George W. Preston; 2. Synthesis of the elements in stars: B2FH and beyond E. Margaret Burbidge; 3. Stellar nucleosynthesis: a status report 2003 David Arnett; 4. Advances in r-process nucleosynthesis John J. Cowan and Christopher Sneden; 5. Element yields of intermediate-mass stars Richard B. C. Henry; 6. The impact of rotation on chemical abundances in red giant branch stars Corinne Charbonnel; 7. s-processing in AGB stars and the composition of carbon stars Maurizio Busso, Oscar Straniero, Roberto Gallino, and Carlos Abia; 8. Models of chemical evolution Francesca Matteucci; 9. Model atmospheres and stellar abundance analysis Bengt Gustafsson; 10. The light elements: lithium, beryllium, and boron Ann Merchant Boesgaard; 11. Extremely metal-poor stars John E. Norris; 12. Thin and thick galactic disks Poul E. Nissen; 13. Globular clusters and halo field stars Christopher Sneden, Inese I. Ivans and Jon P. Fulbright; 14. Chemical evolution in ω Centauri Verne V. Smith; 15. Chemical composition of the Magellanic Clouds, from young to old stars Vanessa Hill; 16. Detailed composition of stars in dwarf spheroidal galaxies Matthew D. Shetrone; 17. The evolutionary history of Local Group irregular galaxies Eva K. Grebel; 18. Chemical evolution of the old stellar populations of M31 R. Michael Rich; 19. Stellar winds of hot massive stars nearby and beyond the Local Group Fabio Bresolin and Rolf P. Kudritzki; 20. Presolar stardust grains Donald D. Clayton and Larry R. Nittler; 21. Interstellar dust B. T. Draine; 22. Interstellar atomic abundances Edward B. Jenkins; 23. Molecules in the interstellar medium Tommy Wiklind; 24. Metal ejection by galactic winds Crystal L. Martin; 25. Abundances from the integrated light of globular clusters and galaxies Scott C. Trager; 26. Abundances in spiral and irregular galaxies Donald R. Garnett; 27

  20. Detonation-synthesis nanodiamonds: synthesis, structure, properties and applications

    Energy Technology Data Exchange (ETDEWEB)

    Dolmatov, Valerii Yu [Federal State Unitary Enterprise Special Design-Technology Bureau (FSUE SDTB) ' ' Tekhnolog' ' at the St Petersburg State Institute of Technology (Technical University) (Russian Federation)

    2007-04-30

    The review outlines the theoretical foundations and industrial implementations of modern detonation synthesis of nanodiamonds and chemical purification of the nanodiamonds thus obtained. The structure, key properties and promising fields of application of detonation-synthesis nanodiamonds are considered.

  1. Detonation-synthesis nanodiamonds: synthesis, structure, properties and applications

    International Nuclear Information System (INIS)

    Dolmatov, Valerii Yu

    2007-01-01

    The review outlines the theoretical foundations and industrial implementations of modern detonation synthesis of nanodiamonds and chemical purification of the nanodiamonds thus obtained. The structure, key properties and promising fields of application of detonation-synthesis nanodiamonds are considered.

  2. The Chemistry of Superheavy Elements

    CERN Document Server

    Schädel, M

    2003-01-01

    The chemistry of transactinide or superheavy elements has reached element 108. Preparations are under way to leap to element 112 and beyond. The current status of this atom-at-a-time chemical research and its future perspectives are reviewed from an experimental point of view together with some of the interesting results from n -rich nuclides near and at the N=162 neutron shell. Experimental techniques and important results enlightening typical chemical properties of elements 104 through 108 are presented in an exemplary way. From the results of these experiments it is justified to place these elements in the Periodic Table of the Elements in to groups 4 through 8, respectively. However, mainly due to the influence of relativistic effects, it is no longer possible to deduce detailed chemical properties of these superheavy elements simply from this position.

  3. Transplutonium elements - a literature survey

    International Nuclear Information System (INIS)

    Sivaramakrishnan, C.K.; Jadhav, A.V.

    1974-01-01

    The report surveys reported work on the discovery of transplutonium elements and their production through various methods like bombardment of heavy elements with charged ions, successive neutron captures on heavy elements in reactors and multiple neutron captures by heavy elements during nuclear explosions. Estimated yields of transplutonium elements in special targets irradiated in reactors, and also as byproducts from spent power reactor fuels are quoted. Various chemical procedures adopted for recovery of these elements from irradiated target and also from power reactor fuel reprocessing streams are described. A brief survey of shielded facilities available at various centres for transplutonium programmes is also included. Major uses of some of these heavy elements are described. (author)

  4. Friedel-Crafts Alkylation Using Elemental Aluminum Catalyst: An Undergraduate Laboratory Experiment.

    Science.gov (United States)

    Meeks, B. Spencer; Lucas, Anita R.

    1989-01-01

    Provides methodology for carrying out the synthesis of sec-butyltoluene by the Friedel-Crafts alkylation of toluene. Suggests using simple elemental aluminum as the catalyst in place of AlCl3 or amalgamated aluminum. Notes satisfactory results for both macro- and microscale operations. (MVL)

  5. Noncovalent synthesis of protein dendrimers

    NARCIS (Netherlands)

    Lempens, E.H.M.; Baal, van I.; Dongen, van J.L.J.; Hackeng, T.M.; Merkx, M.; Meijer, E.W.

    2009-01-01

    The covalent synthesis of complex biomolecular systems such as multivalent protein dendrimers often proceeds with low efficiency, thereby making alternative strategies based on noncovalent chemistry of high interest. Here, the synthesis of protein dendrimers using a strong but noncovalent

  6. EAF optimal managing elements

    Science.gov (United States)

    Ioana, A.; Constantin, N.; Dragna, E. C.

    2017-01-01

    Electric Arc Furnaces (EAF) is an important and complex aggregate. We present elements of EAF operating efficiency. The reliability of the EAF is mainly determined by electric circuit reliability and especially of the transformator of the furnace. This due to the fact that, in an electric steel plant, the objective „24 tapping/day” involves. Due to the complexity of the process, the EAF operation needs a computer usage and, in his componence, it must have two independent calculation units (UC1) and (UC2). Based on these two input sets (Σi1) and ((Σi2), the calculation unit (UC1) builds the general operation procedure based on mathematical methods. For that purpose, there are used the results of the 5 mathematical methods: the mathematical model to write-off the function objective (M.F.O.); the mathematical model of calculating the charge (M.C.C.); the mathematical model of conducting the effective melt (M.C.M.); the mathematical model of reheating the charge (M.R.C.); the mathematical model of blasting the reactive dusts (M.B.R.D.).

  7. Nuclear fuel element

    International Nuclear Information System (INIS)

    Armijo, J.S.

    1977-01-01

    A nuclear fuel element for use in the core of a nuclear reactor is disclosed which has a composite cladding having a substrate, a metal barrier metallurgically bonded to the inside surface of the substrate and an inner layer metallurgically bonded to the inside surface of the metal barrier. In this composite cladding, the inner layer and the metal barrier shield the substrate from any impurities or fission products from the nuclear fuel material held within the composite cladding. The metal barrier forms about 1 to about 4 percent of the thickness of the cladding and is comprised of a metal selected from the group consisting of niobium, aluminum, copper, nickel, stainless steel, and iron. The inner layer and then the metal barrier serve as reaction sites for volatile impurities and fission products and protect the substrate from contact and reaction with such impurities and fission products. The substrate and the inner layer of the composite cladding are selected from conventional cladding materials and preferably are a zirconium alloy. Also in a preferred embodiment the substrate and the inner layer are comprised of the same material, preferably a zirconium alloy. 19 claims, 2 figures

  8. Neutron absorbing element

    International Nuclear Information System (INIS)

    Kasai, Shigeo.

    1991-01-01

    The present invention concerns a neutron absorbing element of a neutron shielding member used for an LMFBR type reactor. The inside of a fuel can sealed at both of the upper and the lower ends thereof with plugs is partitioned into an upper and a lower chambers by an intermediate plug. A discharging hole is disposed at the upper end plug, which is in communication with the outside. A communication tube is disposed at the intermediate end plug and it is in communication with the lower chamber containing B 4 C pellets. A cylindrical support member having three porous plugs connected in series is disposed at the lower surface of the discharging hole provided at the upper end plug. Further, the end of the discharging hole is sealed with high temperature solder and He atmosphere is present at the inside of the fuel can. With such a constitution, the supporting differential pressure of the porous plugs can be made greater while discharging He gases generated from B 4 C to the outside. Further, the porous plugs can be surely wetted by coolants. Accordingly, it is possible to increase life time and shorten the size. (I.N.)

  9. Chemistry of transuranium elements

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    The half-wave amalgamation potential of No (element 102) was determined. Studies on the preparation and properties of Cf are reported; previously reported results on Es were confirmed. The heat of solution of Bk was measured. Spectroscopic and x-ray diffraction studies of Es-253 bromides are reported. Salicylate complexes with Sm(III), Am(III), Th(IV), and U(IV)O 2 were prepared; crystal data are given. Results of studies on the effect of secondary bonds on the strength of O double bond Np double bond O bonds are reported. The M series x rays of Np were measured. Anomalous spin--orbit splitting of the 4f level in the actinide series is reported. Progress is reported in studies on the Cf oxide system for oxygen pressures up to 760 mm and temperatures between 25 and 1000 0 C, as well as structural parameters of transplutonium oxysulfates and oxysulfides and actinide and lanthanide hydroxides. The electron paramagnetic resonance spectrum of 253 Es 2+ was observed in the cubic monocrystal hosts BaF 2 and SrCl 2

  10. Synthesis of non-siliceous mesoporous oxides.

    Science.gov (United States)

    Gu, Dong; Schüth, Ferdi

    2014-01-07

    Mesoporous non-siliceous oxides have attracted great interest due to their unique properties and potential applications. Since the discovery of mesoporous silicates in 1990s, organic-inorganic assembly processes by using surfactants or block copolymers as soft templates have been considered as a feasible path for creating mesopores in metal oxides. However, the harsh sol-gel conditions and low thermal stabilities have limited the expansion of this method to various metal oxide species. Nanocasting, using ordered mesoporous silica or carbon as a hard template, has provided possibilities for preparing novel mesoporous materials with new structures, compositions and high thermal stabilities. This review concerns the synthesis, composition, and parameter control of mesoporous non-siliceous oxides. Four synthesis routes, i.e. soft-templating (surfactants or block copolymers as templates), hard-templating (mesoporous silicas or carbons as sacrificial templates), colloidal crystal templating (3-D ordered colloidal particles as a template), and super lattice routes, are summarized in this review. Mesoporous metal oxides with different compositions have different properties. Non-siliceous mesoporous oxides are comprehensively described, including a discussion of constituting elements, synthesis, and structures. General aspects concerning pore size control, atomic scale crystallinity, and phase control are also reviewed.

  11. Chemistry of the superheavy elements.

    Science.gov (United States)

    Schädel, Matthias

    2015-03-13

    The quest for superheavy elements (SHEs) is driven by the desire to find and explore one of the extreme limits of existence of matter. These elements exist solely due to their nuclear shell stabilization. All 15 presently 'known' SHEs (11 are officially 'discovered' and named) up to element 118 are short-lived and are man-made atom-at-a-time in heavy ion induced nuclear reactions. They are identical to the transactinide elements located in the seventh period of the periodic table beginning with rutherfordium (element 104), dubnium (element 105) and seaborgium (element 106) in groups 4, 5 and 6, respectively. Their chemical properties are often surprising and unexpected from simple extrapolations. After hassium (element 108), chemistry has now reached copernicium (element 112) and flerovium (element 114). For the later ones, the focus is on questions of their metallic or possibly noble gas-like character originating from interplay of most pronounced relativistic effects and electron-shell effects. SHEs provide unique opportunities to get insights into the influence of strong relativistic effects on the atomic electrons and to probe 'relativistically' influenced chemical properties and the architecture of the periodic table at its farthest reach. In addition, they establish a test bench to challenge the validity and predictive power of modern fully relativistic quantum chemical models. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

  12. Experimental Study of Elements Promoting Mixing in Fuel Elements

    International Nuclear Information System (INIS)

    Silin, Nicolas; Juanico, Luis; Delmastro, Dario

    2003-01-01

    In the present work a thermal tracing technique is used to measure the increase of the mixing between subchannels in the presence of different mixing elements.As representative elements a spacer, a spacer with mixing vanes and turbulence promoter buttons were considered.The performance of these elements was evaluated by studying the behavior of a thermal trace in each case.Also the pressure drop for each case is presented.The results present a qualitative and quantitative guide for the application of each one of these appendages in future nuclear elements

  13. Behavioral synthesis of asynchronous circuits

    DEFF Research Database (Denmark)

    Nielsen, Sune Fallgaard

    2005-01-01

    This thesis presents a method for behavioral synthesis of asynchronous circuits, which aims at providing a synthesis flow which uses and tranfers methods from synchronous circuits to asynchronous circuits. We move the synchronous behavioral synthesis abstraction into the asynchronous handshake...... is idle. This reduces unnecessary switching activity in the individual functional units and therefore the energy consumption of the entire circuit. A collection of behavioral synthesis algorithms have been developed allowing the designer to perform time and power constrained design space exploration...

  14. Click synthesis of PET radiopharmaceuticals

    International Nuclear Information System (INIS)

    Xu Mei; Kuang Chunxiang

    2009-01-01

    Increasing attention has been focused on synthesis radiopharmaceuticals for positron emission tomography (PET). The recent years witnessed applications of click chemistry to PET radiopharmaceutical synthesis,because of its distinctive advantages including high speed,yield and stereospecificity under mild conditions. Synthesis of 18 F-labeled and 11 C-labeled radiopharmaceuticals and intermediates via click chemistry are reviewed. The future trend of click chemistry for the synthesis of PET radiopharmaceutical is prospected. (authors)

  15. Enhancement of RNA synthesis by promoter duplication in tombusviruses

    International Nuclear Information System (INIS)

    Panavas, T.; Panaviene, Z.; Pogany, J.; Nagy, P.D.

    2003-01-01

    Replication of tombusviruses, small plus-strand RNA viruses of plants, is regulated by cis-acting elements present in the viral RNA. The role of cis-acting elements can be studied in vitro by using a partially purified RNA-dependent RNA polymerase (RdRp) preparation obtained from tombusvirus-infected plants , Virology 276, 279- 288). Here, we demonstrate that the minus-strand RNA of tombusviruses contains, in addition to the 3'-terminal minimal plus-strand initiation promoter, a second cis-acting element, termed the promoter proximal enhancer (PPE). The PPE element enhanced RNA synthesis by almost threefold from the adjacent minimal promoter in the in vitro assay. The sequence of the PPE element is 70% similar to the minimal promoter, suggesting that sequence duplication of the minimal promoter may have been the mechanism leading to the generation of the PPE. Consistent with this proposal, replacement of the PPE element with the minimal promoter, which resulted in a perfectly duplicated promoter region, preserved its enhancer-like function. In contrast, mutagenesis of the PPE element or its replacement with an artificial G/C-rich sequence abolished its stimulative effect on initiation of RNA synthesis in vitro. In vivo experiments are also consistent with the role of the PPE element in enhancement of tombusvirus replication. Sequence comparison of several tombusviruses and related carmoviruses further supports the finding that duplication of minimal promoter sequences may have been an important mechanism during the evolution of cis-acting elements in tombusviruses and related RNA viruses

  16. Supercritical Synthesis of Biodiesel

    Directory of Open Access Journals (Sweden)

    Michel Vaultier

    2012-07-01

    Full Text Available The synthesis of biodiesel fuel from lipids (vegetable oils and animal fats has gained in importance as a possible source of renewable non-fossil energy in an attempt to reduce our dependence on petroleum-based fuels. The catalytic processes commonly used for the production of biodiesel fuel present a series of limitations and drawbacks, among them the high energy consumption required for complex purification operations and undesirable side reactions. Supercritical fluid (SCF technologies offer an interesting alternative to conventional processes for preparing biodiesel. This review highlights the advances, advantages, drawbacks and new tendencies involved in the use of supercritical fluids (SCFs for biodiesel synthesis.

  17. Toleration, Synthesis or Replacement?

    DEFF Research Database (Denmark)

    Holtermann, Jakob v. H.; Madsen, Mikael Rask

    2016-01-01

    , in order to answer is not yet another partisan suggestion, but rather an attempt at making intelligible both the oppositions and the possibilities of synthesis between normative and empirical approaches to law. Based on our assessment and rational reconstruction of current arguments and positions, we...... therefore outline a taxonomy consisting of the following three basic, ideal-types in terms of the epistemological understanding of the interface of law and empirical studies: toleration, synthesis and replacement. This tripartite model proves useful with a view to teasing out and better articulating...

  18. Analog elements for transuranic chemistries

    International Nuclear Information System (INIS)

    Weimer, W.C.

    1982-01-01

    The analytical technique for measuring trace concentrations of the analog rare earth elements has been refined for optimal detection. The technique has been used to determine the rare earth concentrations in a series of geological and biological materials, including samples harvested from controlled lysimeter investigations. These studies have demonstrated that any of the trivalent rare earth elements may be used as analog elements for the trivalent transuranics, americium and curium

  19. Are there different requirements for trace elements in eumelanin- and pheomelanin-based color production? A case study of two passerine species.

    Science.gov (United States)

    Zduniak, Piotr; Surmacki, Adrian; Erciyas-Yavuz, Kiraz; Chudzińska, Maria; Barałkiewicz, Danuta

    2014-09-01

    Melanin is the most common pigment in animal integuments including bird plumage. It has been shown that several trace elements may play roles in the production and signaling function of melanin-colored plumage. We investigated coloration and content of various metal elements in the rectrices of two insectivorous passerines, Common Redstarts (Phoenicurus phoenicurus) and Blackcaps (Sylvia atricapilla), which have eumelanin- and pheomelanin-based coloration, respectively. We hypothesized that 1) the two species would differ in concentrations of metals important in melanin synthesis (Ca, Fe, Cu, Zn), 2) differences in metal concentration levels would be related to feather coloration. Our study confirmed the first prediction and provides the first evidence that selected elements may play a greater role in pheomelanin than in eumelanin synthesis. Concentrations of three elements considered as important in melanin synthesis (Ca, Fe, Zn) were 52% to 93% higher in rusty colored Common Redstart feathers compared to the dark gray Blackcap feathers. However, element concentrations were not correlated with feather coloration or sex in either species. Our study suggests that, of the two melanin forms, pheomelanin synthesis may bear higher costs associated with the acquisition of specific elements or limited elements may create trade-offs between ornamentation and other physiological functions. Our findings warrant further investigations designed to better understand the roles of macro- and microelements in the synthesis of both forms of melanin. Copyright © 2014 Elsevier Inc. All rights reserved.

  20. Multi-Objective Optimization in Physical Synthesis of Integrated Circuits

    CERN Document Server

    A Papa, David

    2013-01-01

    This book introduces techniques that advance the capabilities and strength of modern software tools for physical synthesis, with the ultimate goal to improve the quality of leading-edge semiconductor products.  It provides a comprehensive introduction to physical synthesis and takes the reader methodically from first principles through state-of-the-art optimizations used in cutting edge industrial tools. It explains how to integrate chip optimizations in novel ways to create powerful circuit transformations that help satisfy performance requirements. Broadens the scope of physical synthesis optimization to include accurate transformations operating between the global and local scales; Integrates groups of related transformations to break circular dependencies and increase the number of circuit elements that can be jointly optimized to escape local minima;  Derives several multi-objective optimizations from first observations through complete algorithms and experiments; Describes integrated optimization te...

  1. Optimization of cellulose acrylate and grafted 4-vinylpyridine and 1-vinylimidazole synthesis

    OpenAIRE

    Bojanić Vaso

    2010-01-01

    Optimization of cellulose acrylate synthesis by reaction with sodium cellulosate and acryloyl chloride was carried out. Optimal conditions for conducting the synthesis reaction of cellulose acrylate were as follows: the molar ratio of cellulose/potassium-t-butoxide/acryloyl chloride was 1:3:10 and the optimal reaction time was 10 h. On the basis of elemental analysis with optimal conditions for conducting the reaction of cellulose acrylate, the percentage of substitution of glucose units in c...

  2. Photoshop Elements 10 For Dummies

    CERN Document Server

    Obermeier, Barbara

    2011-01-01

    Perfect your photos and images with this "focused" guide to the latest version of Photoshop Elements For most of us, the professional-level Photoshop is overkill for our needs. Amateur photographers and photo enthusiasts turn to Photoshop Elements for a powerful but simpler way to edit and retouch their snapshots. Photoshop Elements 10 For Dummies, fully updated and revised for the latest release of this software product, helps you navigate Elements to create, edit, fix, share, and organize the high-quality images you desire. Full color pages bring the techniques to life and make taking great

  3. Synthesis and Characterization of Colloidal Metal and Photovoltaic Semiconductor Nanocrystals

    KAUST Repository

    Abulikemu, Mutalifu

    2014-11-05

    Metal and semiconducting nanocrystals have received a great deal of attention from fundamental scientists and application-oriented researchers due to their physical and chemical properties, which differ from those of bulk materials. Nanocrystals are essential building blocks in the development of nanostructured devices for energy conversion. Colloidal metals and metal chalcogenides have been developed for use as nanocrystal inks to produce efficient solar cells with lower costs. All high-performing photovoltaic nanocrystals contain toxic elements, such as Pb, or scarce elements, such as In; thus, the production of solution-processable nanocrystals from earth-abundant materials using environmentally benign synthesis and processing methods has become a major challenge for the inorganic semiconductor-based solar field. This dissertation, divided into two parts, addresses several aspects of these emerging challenges. The first portion of the thesis describes the synthesis and characterization of nanocrystals of antimony sulfide, which is composed of non-scarce and non-toxic elements, and examines their performance in photovoltaic devices. The effect of various synthetic parameters on the final morphology is explored. The structural, optical and morphological properties of the nanocrystals were investigated, and Sb2S3 nanocrystal-based solid-state semiconductor-sensitized solar cells were fabricated using different deposition processes. We achieved promising power conversion efficiencies of 1.48%. The second part of the thesis demonstrates a novel method for the in situ synthesis and patterning of nanocrystals via reactive inkjet printing. The use of low-cost manufacturing approaches for the synthesis of nanocrystals is critical for many applications, including photonics and electronics. In this work, a simple, low-cost method for the synthesis of nanocrystals with minimum size variation and waste using reactive inkjet printing is introduced. As a proof of concept, the

  4. Alpha decay properties of heavy and superheavy elements

    International Nuclear Information System (INIS)

    Vigila Bai, G.M. Carmel; Umai Parvathiy, J.

    2015-01-01

    Analysing accurately the lifetimes of α-decay chains is an important tool to detect and study the properties of superheavy nuclei. 48 Ca is used in the synthesis of superheavy nuclei Z = 106-118 at Dubna. The experimental work of 48 Ca projectiles at Dubna has given an opportunity to study the superheavy element (SHE). Here, the α-decay properties for Z = 106-118 are evaluated using our CYE model and are compared with the available experimental and theoretical values. (author)

  5. Circuit elements at optical frequencies: nanoinductors, nanocapacitors, and nanoresistors.

    Science.gov (United States)

    Engheta, Nader; Salandrino, Alessandro; Alù, Andrea

    2005-08-26

    We present the concept of circuit nanoelements in the optical domain using plasmonic and nonplasmonic nanoparticles. Three basic circuit elements, i.e., nanoinductors, nanocapacitors, and nanoresistors, are discussed in terms of small nanostructures with different material properties. Coupled nanoscale circuits and parallel and series combinations are also envisioned, which may provide road maps for the synthesis of more complex circuits in the IR and visible bands. Ideas for the optical implementation of right-handed and left-handed nanotransmission lines are also forecasted.

  6. Chemical Synthesis of Circular Proteins*

    Science.gov (United States)

    Tam, James P.; Wong, Clarence T. T.

    2012-01-01

    Circular proteins, once thought to be rare, are now commonly found in plants. Their chemical synthesis, once thought to be difficult, is now readily achievable. The enabling methodology is largely due to the advances in entropic chemical ligation to overcome the entropy barrier in coupling the N- and C-terminal ends of large peptide segments for either intermolecular ligation or intramolecular ligation in end-to-end cyclization. Key elements of an entropic chemical ligation consist of a chemoselective capture step merging the N and C termini as a covalently linked O/S-ester intermediate to permit the subsequent step of an intramolecular O/S-N acyl shift to form an amide. Many ligation methods exploit the supernucleophilicity of a thiol side chain at the N terminus for the capture reaction, which makes cysteine-rich peptides ideal candidates for the entropy-driven macrocyclization. Advances in desulfurization and modification of the thiol-containing amino acids at the ligation sites to other amino acids add extra dimensions to the entropy-driven ligation methods. This minireview describes recent advances of entropy-driven ligation to prepare circular proteins with or without a cysteinyl side chain. PMID:22700959

  7. The priming of storage glucan synthesis from bacteria to plants: current knowledge and new developments.

    Science.gov (United States)

    D'Hulst, Christophe; Mérida, Angel

    2010-10-01

    Starch is the main polymer in which carbon and energy are stored in land plants, algae and some cyanobacteria. It plays a crucial role in the physiology of these organisms and also represents an important polymer for humans, in terms of both diet and nonfood industry uses. Recent efforts have elucidated most of the steps involved in the synthesis of starch. However, the process that initiates the synthesis of the starch granule remains unclear. Here, we outline the similarities between the synthesis of starch and the synthesis of glycogen, the other widespread and abundant glucose-based polymer in living cells. We place special emphasis on the mechanisms of initiation of the glycogen granule and current knowledge concerning the initiation of the starch granule. We also discuss recent discoveries regarding the function of starch synthases in the priming of the starch granule and possible interactions with other elements of the starch synthesis machinery.

  8. Towards room temperature, direct, solvent free synthesis of tetraborohydrides

    International Nuclear Information System (INIS)

    Remhof, A; Yan, Y; Friedrichs, O; Kim, J W; Mauron, Ph; Borgschulte, A; Züttel, A; Wallacher, D; Buchsteiner, A; Hoser, A; Oh, K H; Cho, Y W

    2012-01-01

    Due to their high hydrogen content, tetraborohydrides are discussed as potential synthetic energy carriers. On the example of lithium borohydride LiBH 4 , we discuss current approaches of direct, solvent free synthesis based on gas solid reactions of the elements or binary hydrides and/or borides with gaseous H 2 or B 2 H 6 . The direct synthesis from the elements requires high temperature and high pressure (700°C, 150bar D 2 ). Using LiB or AlB 2 as boron source reduces the required temperature by more than 300 K. Reactive milling of LiD with B 2 H 6 leads to the formation of LiBD 4 already at room temperature. The reactive milling technique can also be applied to synthesize other borohydrides from their respective metal hydrides.

  9. Rare-earth elements

    Science.gov (United States)

    Van Gosen, Bradley S.; Verplanck, Philip L.; Seal, Robert R.; Long, Keith R.; Gambogi, Joseph; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

    2017-12-19

    The rare-earth elements (REEs) are 15 elements that range in atomic number from 57 (lanthanum) to 71 (lutetium); they are commonly referred to as the “lanthanides.” Yttrium (atomic number 39) is also commonly regarded as an REE because it shares chemical and physical similarities and has affinities with the lanthanides. Although REEs are not rare in terms of average crustal abundance, the concentrated deposits of REEs are limited in number.Because of their unusual physical and chemical properties, the REEs have diverse defense, energy, industrial, and military technology applications. The glass industry is the leading consumer of REE raw materials, which are used for glass polishing and as additives that provide color and special optical properties to the glass. Lanthanum-based catalysts are used in petroleum refining, and cerium-based catalysts are used in automotive catalytic converters. The use of REEs in magnets is a rapidly increasing application. Neodymium-iron-boron magnets, which are the strongest known type of magnets, are used when space and weight are restrictions. Nickel-metal hydride batteries use anodes made of a lanthanum-based alloys.China, which has led the world production of REEs for decades, accounted for more than 90 percent of global production and supply, on average, during the past decade. Citing a need to retain its limited REE resources to meet domestic requirements as well as concerns about the environmental effects of mining, China began placing restrictions on the supply of REEs in 2010 through the imposition of quotas, licenses, and taxes. As a result, the global rare-earth industry has increased its stockpiling of REEs; explored for deposits outside of China; and promoted new efforts to conserve, recycle, and substitute for REEs. New mine production began at Mount Weld in Western Australia, and numerous other exploration and development projects noted in this chapter are ongoing throughout the world.The REE-bearing minerals are

  10. Stellar population synthesis

    International Nuclear Information System (INIS)

    Pickles, A.J.

    1989-01-01

    The techniques used to derive astrophysically useful information from observations of the integrated light of composite stellar systems are briefly reviewed. A synthesis technique, designed to separate and describe on a standard system the competing effects of age and metallicity variations is introduced, and illustrated by its application to the study of the history of star formation in bright elliptical galaxies in clusters. (author)

  11. Enzymatic synthesis of vanillin

    NARCIS (Netherlands)

    van den Heuvel, RHH; Fraaije, MW; Laane, C; van Berkel, WJH; Heuvel, Robert H.H. van den; Berkel, Willem J.H. van

    Due to increasing interest in natural vanillin, two enzymatic routes for the synthesis of vanillin were developed. The flavoprotein vanillyl alcohol oxidase (VAO) acts on a wide range of phenolic compounds and converts both creosol and vanillylamine to vanillin with high yield. The VAO-mediated

  12. Enzymatic synthesis of vanillin

    NARCIS (Netherlands)

    Heuvel, van den R.H.H.; Fraaije, M.W.; Laane, C.; Berkel, van W.J.H.

    2001-01-01

    Due to increasing interest in natural vanillin, two enzymatic routes for the synthesis of vanillin were developed. The flavoprotein vanillyl alcohol oxidase (VAO) acts on a wide range of phenolic compounds and converts both creosol and vanillylamine to vanillin with high yield. The VAO-mediated

  13. Synthesis de 1-dotriacotanol

    International Nuclear Information System (INIS)

    Hernandez, L.; Gonzalez, J.C.

    1996-01-01

    In order to prepare isotopic labeled long chain aliphatic primary alcohol's, the synthesis overall yielding and chemical purity of 1-dotriacotanol were 41% and 98%, respectively. This procedure is very useful for carbon-14 and tritium labeling at Beta position of saturated fatty alcohol's

  14. Synthesis of acrylic prepolymer

    International Nuclear Information System (INIS)

    Hussin bin Mohd Nor; Dahlan bin Haji Mohd; Mohamad Hilmi bin Mahmood.

    1988-04-01

    An acrylic prepolymer was synthesized from glycidyl methacrylate (GMA), butyl methacrylate (BMA), methyl methacrylate (MMA) and acrylic acid (AA). Butyl acetate (BAc), benzoyl peroxide (BzO), 4-methoxyphenol (MPh) and triethylamine (TEA) were used as solvent, initiator, inhibitor and catalyst respectively. Observations of the synthesis leading to the formation of acrylic prepolymer are described. (author)

  15. Synthesis of new radiotracers

    International Nuclear Information System (INIS)

    Chahed, Ahlem

    2008-01-01

    The brain's sensibility besides to the rigorous selectivity of changes taking place on brain's barriers leads us to synthesis specifics radiotracers based on diamine ethylene and marked with technetium radioisotope to form a radiotracer able to pass these barriers and diagnose illnesses in an early stage. These radiotracers are tested by a biodistribution on a small animal to be ratified. (Author)

  16. Synthesis of arabinoxylan fragments

    DEFF Research Database (Denmark)

    Underlin, Emilie Nørmølle; Böhm, Maximilian F.; Madsen, Robert

    , or production of commercial chemicals which are mainly obtained from fossil fuels today.The arbinoxylan fragments have a backbone of β-1,4-linked xylans with α-L-arabinose units attached at specific positions. The synthesis ultilises an efficient synthetic route, where all the xylan units can be derived from D...

  17. [Synthesis of new nitrosoureas].

    Science.gov (United States)

    Papadaki-Valiraki, A; Siatra-Papastaikoudi, T; Skaltsounis, A L; Roussakis, C

    1989-01-01

    Two chemical pathways were used for the synthesis of three new N'-(2-chloroethyl)-N-[2-(4-alkoxyphenylthio)ethyl]-N'-nitrosoureas and two new N'-(2-chloroethyl)-N)[2-(4-alkoxyphenyl-thio)ethyl]-N-nitrosoureas . The study of the cytotoxicity of the three N'-nitrosoureas, was carried out in two experimental models (P 388 and NSCLCN6).

  18. MICROWAVES IN ORGANIC SYNTHESIS

    Science.gov (United States)

    The effect of microwaves, a non-ionizing radiation, on organic reactions is described both in polar solvents and under solvent-free conditions. The special applications are highlighted in the context of solventless organic synthesis which involve microwave (MW) exposure of neat r...

  19. SYNTHESIS, CHARACTERIZATION AND ANTIBACTERIAL ...

    African Journals Online (AJOL)

    Preferred Customer

    In the present study, synthesis, and biological evaluation of some novel ... Then slowly cooled and resultant mixture was basified with aqueous sodium hydroxide ... mol), anhydrous potassium carbonate (5.52 g, 0.04 mol) in acetone (25 mL), ...

  20. Synthesis, characterization and properties

    Indian Academy of Sciences (India)

    Unknown

    work, we report herein the synthesis, structural cha- racterization and properties of a chiral Mn(IV) mononuclear ... atmosphere with a platinum disc working electrode, a platinum wire auxiliary electrode and a Ag/AgCl ... SMART APEX CCD area detector system [λ(Mo-. Kα) = 0⋅71073 Å], graphite monochromator, 2400.

  1. Nuclear reactions and synthesis of new transuranium species

    International Nuclear Information System (INIS)

    Seaborg, G.T.

    1983-01-01

    In this short review, I shall describe the special aspects of heavy ion nuclear reaction mechanisms operative in the transuranium region, the role of new techniques, possible nuclear reactions for the production of additional transuranium elements and nuclear species and the importance of work in this region for the development of nuclear models and theoretical concepts. This discussion should make it clear that a continuing supply of leements and isotopes, some fo them relatively short-lived, produced by the HFIR-TRU facilities, will be a requirement for future synthesis of new elements and isotopes

  2. Rack for nuclear fuel elements

    International Nuclear Information System (INIS)

    Rubinstein, H.J.; Gordon, C.B.; Robison, A.; Clark, P.M.

    1977-01-01

    Disclosed is a rack for storing spent nuclear fuel elements in which a plurality of aligned rows of upright enclosures of generally square cross-sectional areas contain vertically disposed spent fuel elements. Each fuel element is supported at the lower end thereof by a respective support that rests on the floor of the spent fuel pool for a nuclear power plant. An open rack frame is employed as an upright support for the enclosures containing the spent fuel elements. Legs at the lower corners of the frame rest on the floor of the pool to support the frame. In one exemplary embodiment, the support for the fuel element is in the form of a base on which a fuel element rests and the base is supported by legs. In another exemplary embodiment, each fuel element is supported on the pool floor by a self-adjusting support in the form of a base on which a fuel element rests and the base rests on a ball or swivel joint for self-alignment. The lower four corners of the frame are supported by legs adjustable in height for leveling the frame. Each adjustable frame leg is in the form of a base resting on the pool floor and the base supports a threaded post. The threaded post adjustably engages a threaded column on which rests the lower end of the frame. 16 claims, 14 figures

  3. Thermal insulation of fuel elements

    International Nuclear Information System (INIS)

    Dubrovcak, P.; Pec, V.; Pitonak, J.

    1978-01-01

    The claim of the invention concerns thermal insulation of fuel elements heated for measurement of uranium fuel physical properties. For this, layers of aluminium film and of glass fibre are wound onto the inner tube of the element cladding. The space between the inner and the outer tubes is evacuated and the tubes are spaced using spacer wires. (M.S.)

  4. On symmetric pyramidal finite elements

    Czech Academy of Sciences Publication Activity Database

    Liu, L.; Davies, K. B.; Yuan, K.; Křížek, Michal

    2004-01-01

    Roč. 11, 1-2 (2004), s. 213-227 ISSN 1492-8760 R&D Projects: GA AV ČR IAA1019201 Institutional research plan: CEZ:AV0Z1019905 Keywords : mesh generation * finite element method * composite elements Subject RIV: BA - General Mathematics Impact factor: 0.108, year: 2004

  5. Fluid element in SAP IV

    International Nuclear Information System (INIS)

    Yilmaz, C.; Akkas, N.

    1979-01-01

    In previous studies a fluid element is incorporated in the widely used general purpose finite element program SAPIV. This type of problem is of interest in the design of nuclear components involving geometric complexities and nonlinearities. The elasticity matrix of a general-purpose finite element program is modified in such a way that it becomes possible to idealize fluid as a structural finite element with zero shear modulus and a given bulk modules. Using the modified version of SAPIV, several solid-fluid interactions problems are solved. The numerical solutions are compared with the available analytical solutions. They are shown to be in reasonable aggrement. It is also shown that by solving an exterior-fluid interaction problem, the pressure wave propagation in the acoustic medium can be solved with the same approach. In this study, two of the problem not studied in the previous work will be presented. These problems are namely the effects of the link elements used at solid-fluid interfaces and of the concentrated loads on the response of the fluid medium. Truss elements are used as the link elements. After these investigations, it is decided that general purpose finite element programs with slight modifications can be used in the safety analysis of nuclear reactor plants. By this procedure it is possible to handle two-dimensional plane strain and tridimensional axisymmetric problems of this type. (orig.)

  6. Repetitive elements in parasitic protozoa

    Directory of Open Access Journals (Sweden)

    Clayton Christine

    2010-05-01

    Full Text Available Abstract A recent paper published in BMC Genomics suggests that retrotransposition may be active in the human gut parasite Entamoeba histolytica. This adds to our knowledge of the various types of repetitive elements in parasitic protists and the potential influence of such elements on pathogenicity. See research article http://www.biomedcentral.com/1471-2164/11/321

  7. Synthesis of concentric circular antenna arrays using dragonfly algorithm

    Science.gov (United States)

    Babayigit, B.

    2018-05-01

    Due to the strong non-linear relationship between the array factor and the array elements, concentric circular antenna array (CCAA) synthesis problem is challenging. Nature-inspired optimisation techniques have been playing an important role in solving array synthesis problems. Dragonfly algorithm (DA) is a novel nature-inspired optimisation technique which is based on the static and dynamic swarming behaviours of dragonflies in nature. This paper presents the design of CCAAs to get low sidelobes using DA. The effectiveness of the proposed DA is investigated in two different (with and without centre element) cases of two three-ring (having 4-, 6-, 8-element or 8-, 10-, 12-element) CCAA design. The radiation pattern of each design cases is obtained by finding optimal excitation weights of the array elements using DA. Simulation results show that the proposed algorithm outperforms the other state-of-the-art techniques (symbiotic organisms search, biogeography-based optimisation, sequential quadratic programming, opposition-based gravitational search algorithm, cat swarm optimisation, firefly algorithm, evolutionary programming) for all design cases. DA can be a promising technique for electromagnetic problems.

  8. Synthesis of Cyclic Py-Im Polyamide Libraries

    OpenAIRE

    Li, Benjamin C.; Montgomery, David C.; Puckett, James W.; Dervan, Peter B.

    2013-01-01

    Cyclic Py-Im polyamides containing two GABA turn units exhibit enhanced DNA binding affinity, but extensive studies of their biological properties have been hindered due to synthetic inaccessibility. A facile modular approach toward cyclic polyamides has been developed via microwave-assisted solid-phase synthesis of hairpin amino acid oligomer intermediates followed by macrocyclization. A focused library of cyclic polyamides 1–7 targeted to the androgen response element (ARE) and the estrogen...

  9. Boric Acid Catalyzed Convenient Synthesis of Benzimidazoles in Aqueous Media

    OpenAIRE

    Poor Heravi, Mohammad Reza; Ashori, Marjan

    2013-01-01

    Synthesis of benzimidazoles has been developed by the o-phenylenediamine with aldehydes using boric acid an efficient catalyst under mild reaction conditions in aqueous media. The product is applicable to aryl and heteroaryl aldehydes. This reaction led to the formation of benzimidazoles new derivatives in good yields. The FT-IR, 19F-NMR, 1H-NMR, 13C-NMR spectra and elemental analysis confirm the structure of compounds.

  10. Boric Acid Catalyzed Convenient Synthesis of Benzimidazoles in Aqueous Media

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Poor Heravi

    2013-01-01

    Full Text Available Synthesis of benzimidazoles has been developed by the o-phenylenediamine with aldehydes using boric acid an efficient catalyst under mild reaction conditions in aqueous media. The product is applicable to aryl and heteroaryl aldehydes. This reaction led to the formation of benzimidazoles new derivatives in good yields. The FT-IR, 19F-NMR, 1H-NMR, 13C-NMR spectra and elemental analysis confirm the structure of compounds.

  11. Industrial scale gene synthesis.

    Science.gov (United States)

    Notka, Frank; Liss, Michael; Wagner, Ralf

    2011-01-01

    The most recent developments in the area of deep DNA sequencing and downstream quantitative and functional analysis are rapidly adding a new dimension to understanding biochemical pathways and metabolic interdependencies. These increasing insights pave the way to designing new strategies that address public needs, including environmental applications and therapeutic inventions, or novel cell factories for sustainable and reconcilable energy or chemicals sources. Adding yet another level is building upon nonnaturally occurring networks and pathways. Recent developments in synthetic biology have created economic and reliable options for designing and synthesizing genes, operons, and eventually complete genomes. Meanwhile, high-throughput design and synthesis of extremely comprehensive DNA sequences have evolved into an enabling technology already indispensable in various life science sectors today. Here, we describe the industrial perspective of modern gene synthesis and its relationship with synthetic biology. Gene synthesis contributed significantly to the emergence of synthetic biology by not only providing the genetic material in high quality and quantity but also enabling its assembly, according to engineering design principles, in a standardized format. Synthetic biology on the other hand, added the need for assembling complex circuits and large complexes, thus fostering the development of appropriate methods and expanding the scope of applications. Synthetic biology has also stimulated interdisciplinary collaboration as well as integration of the broader public by addressing socioeconomic, philosophical, ethical, political, and legal opportunities and concerns. The demand-driven technological achievements of gene synthesis and the implemented processes are exemplified by an industrial setting of large-scale gene synthesis, describing production from order to delivery. Copyright © 2011 Elsevier Inc. All rights reserved.

  12. Trace elements in human milk

    Energy Technology Data Exchange (ETDEWEB)

    Parr, R M [International Atomic Energy Agency, Vienna (Austria). Div. of Life Sciences

    1983-06-01

    Trace elements are those elements having a concentration lower than 10 ppm in body fluids or tissues. A total of 24 elements, both trace and minor elements, present in human milk have been analysed in this study, employing neutron activation analysis and absorption spectroscopy. The analyses have been carried out collaboratively by several different laboratories and the Agency which has also served as a coordinating centre. Although the evaluation of the results, altogether 8500 separate values, is still in progress, enough evidence is already available, however, to show some very interesting differences between different study areas and, in some cases, between different socio-economic groups within a single country. The main value of these data will probably be to throw new light on the nutritional requirements of young babies for trace elements.

  13. Massively Parallel Finite Element Programming

    KAUST Repository

    Heister, Timo

    2010-01-01

    Today\\'s large finite element simulations require parallel algorithms to scale on clusters with thousands or tens of thousands of processor cores. We present data structures and algorithms to take advantage of the power of high performance computers in generic finite element codes. Existing generic finite element libraries often restrict the parallelization to parallel linear algebra routines. This is a limiting factor when solving on more than a few hundreds of cores. We describe routines for distributed storage of all major components coupled with efficient, scalable algorithms. We give an overview of our effort to enable the modern and generic finite element library deal.II to take advantage of the power of large clusters. In particular, we describe the construction of a distributed mesh and develop algorithms to fully parallelize the finite element calculation. Numerical results demonstrate good scalability. © 2010 Springer-Verlag.

  14. Massively Parallel Finite Element Programming

    KAUST Repository

    Heister, Timo; Kronbichler, Martin; Bangerth, Wolfgang

    2010-01-01

    Today's large finite element simulations require parallel algorithms to scale on clusters with thousands or tens of thousands of processor cores. We present data structures and algorithms to take advantage of the power of high performance computers in generic finite element codes. Existing generic finite element libraries often restrict the parallelization to parallel linear algebra routines. This is a limiting factor when solving on more than a few hundreds of cores. We describe routines for distributed storage of all major components coupled with efficient, scalable algorithms. We give an overview of our effort to enable the modern and generic finite element library deal.II to take advantage of the power of large clusters. In particular, we describe the construction of a distributed mesh and develop algorithms to fully parallelize the finite element calculation. Numerical results demonstrate good scalability. © 2010 Springer-Verlag.

  15. Spallation RI beam facility and heavy element nuclear chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Nagame, Yuichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-11-01

    An outline of the spallation RI (Radioactive Ion) beam facility is presented. Neutron-rich nuclides are produced in the reaction of high intensity (10-1000 {mu}A) protons with energy of 1.5 GeV and an uranium carbide target. Produced nuclides are ionized in an isotope separator on-line (ISOL) and accelerated by the JAERI tandem and the booster linac. Current progress and a future project on the development of the RI beam facility are given. Studies of transactinide elements, including the synthesis of superheavy elements, nuclear structure far from stability, and RI-probed material science are planned with RI beams. An outlook of the transactinide nuclear chemistry studies using neutron-rich RI beams is described. (author)

  16. Fission in the landscape of heaviest elements: Some recent examples

    International Nuclear Information System (INIS)

    Khuyagbaatar, J.; Yakushev, A.; Düllmann, Ch.E.; Ackermann, D.; Andersson, L.-L.; Block, M.; Brand, H.; Even, J.; Forsberg, University; Hartmann, W.; Herzberg, R.-D.; Heßberger, F.P.; Hoffmann, J.; Hübner, A.; Jäger, E.; Jeppsson, J.; Kindler, B.; Kratz, J.V.; Krier, J.; Kurz, N.; Lommel, B.; Maiti, M.; Minami, S.; Rudolph, D.; Runke, J.; Sarmiento, L.G.; Schädel, M.; Schausten, B.; Steiner, J.; Heidenreich, T. Torres De; Uusitalo, J.; Wiehl, N.; Yakusheva, V.

    2016-01-01

    The fission process still remains a main factor that determines the stability of the atomic nucleus of heaviest elements. Fission half-lives vary over a wide range, 10"−"1"9−10"2"4 s. Present experimental techniques for the synthesis of the superheavy elements that usually measure α-decay chains are sensitive only in a limited range of half-lives, often 10"−"5−10"3 s. In the past years, measurement techniques for very short-lived and very long-lived nuclei were significantly improved at the gas-filled recoil separator TASCA at GSI Darmstadt. Recently, several experimental studies of fission-related phenomena have successfully been performed. In this paper, results on "2"5"4"−"2"5"6Rf and "2"6"6Lr are presented and corresponding factors for retarding the fission process are discussed.

  17. On the production of heavy elements by cold fusion

    International Nuclear Information System (INIS)

    Armbruster, P.

    1985-01-01

    After a short historical introduction (Section 1), this article presents new insights into the mechanism limiting the fusion of heavy nuclides (Section 2). Fusion is finally limited by the increasing Coulomb forces in the formation process of a compound system, as well as in its deexcitation. Moreover, nuclear structure effects in all stages of evaporation residue (EVR) formation are shown to be of importance. The wide field of fusion reaction studies and possible experimental techniques is projected onto the task of element synthesis, and only those aspects that are of relevance here are covered. The better understanding of EVR formation (Section 2) and the new experimental techniques (Section 3) that enabled the production of elements 107-109 (Section 4) are also discussed. In Section 5 ground-state properties and the nuclear structure of the heaviest isotopes, together with their production cross sections, are discussed. Finally, an outlook on how eventually to go beyond Z = 109 is given

  18. New results on elements 111 and 112

    International Nuclear Information System (INIS)

    Hofmann, S.; Hessberger, F.P.; Ackermann, D.

    2002-01-01

    Experiments on the synthesis and identification of the nuclei 272 111 and 277 112 were performed in order to confirm previous results. Three additional decay chains were measured in the reaction 64 Ni + 209 Bi → 273 111 * . The study revealed considerably improved data on the decay chain originating from 272 111. One additional chain was measured in the reaction 70 Zn + 208 Pb → 278 112 * . The decay properties of the chain starting at 277 112 are in excellent agreement with the second chain of the first experiment down to 265 Sg, where the new chain ends by a previously unknown spontaneous-fission branch. A re-analysis of all data on elements 110, 111, and 112 measured at GSI since 1994 (a total of 34 decay chains was investigated) revealed that for 2 chains (second chain of 269 110 measured in 1994 and first chain of 277 112 measured in 1996) the results of the new analysis differed from the previous one. In all other cases the earlier data are exactly reproduced. (orig.)

  19. Platinum-group elements

    Science.gov (United States)

    Zientek, Michael L.; Loferski, Patricia J.; Parks, Heather L.; Schulte, Ruth F.; Seal, Robert R.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

    2017-12-19

    The platinum-group elements (PGEs)—platinum, palladium, rhodium, ruthenium, iridium, and osmium—are metals that have similar physical and chemical properties and tend to occur together in nature. PGEs are indispensable to many industrial applications but are mined in only a few places. The availability and accessibility of PGEs could be disrupted by economic, environmental, political, and social events. The United States net import reliance as a percentage of apparent consumption is about 90 percent.PGEs have many industrial applications. They are used in catalytic converters to reduce carbon monoxide, hydrocarbon, and nitrous oxide emissions in automobile exhaust. The chemical industry requires platinum or platinum-rhodium alloys to manufacture nitric oxide, which is the raw material used to manufacture explosives, fertilizers, and nitric acid. In the petrochemical industry, platinum-supported catalysts are needed to refine crude oil and to produce aromatic compounds and high-octane gasoline. Alloys of PGEs are exceptionally hard and durable, making them the best known coating for industrial crucibles used in the manufacture of chemicals and synthetic materials. PGEs are used by the glass manufacturing industry in the production of fiberglass and flat-panel and liquid crystal displays. In the electronics industry, PGEs are used in computer hard disks, hybridized integrated circuits, and multilayer ceramic capacitors.Aside from their industrial applications, PGEs are used in such other fields as health, consumer goods, and finance. Platinum, for example, is used in medical implants, such as pacemakers, and PGEs are used in cancer-fighting drugs. Platinum alloys are an ideal choice for jewelry because of their white color, strength, and resistance to tarnish. Platinum, palladium, and rhodium in the form of coins and bars are also used as investment commodities, and various financial instruments based on the value of these PGEs are traded on major exchanges

  20. The problem of oxidation state stabilisation and some regularities of a Periodic system of the elements

    International Nuclear Information System (INIS)

    Kiselev, Yurii M; Tretyakov, Yuri D

    1999-01-01

    The general principles of the concept of oxidation state stabilisation are formulated. Problems associated with the preparation and provision of the highest valent forms of transition elements are considered. The empirical data concerning the synthesis of new compounds of rare-earth elements and d elements in unusually high oxidation states are analysed. The possibility of occurrence of the oxidation states + 9 and + 10 for some elements (for example, for iridium and platinum in tetraoxo ions) are discussed. Approaches to the realisation of these states are outlined and it is demonstrated that solid phases or matrices containing alkali metal cations are the most promising systems for the stabilisation of these high oxidation states. Selected thermodynamic features typical of metal halides and oxides and the regularities of the changes in the extreme oxidation states of d elements are considered. The bibliography includes 266 references.

  1. Chemistry of the heaviest elements

    International Nuclear Information System (INIS)

    Hoffman, D.C.

    1996-01-01

    Studies of the chemical properties of the elements at the uppermost end of the periodic table are discussed. Some historical perspective is given, but major emphasis is on recent studies. Isotopes of these elements are short-lived and, therefore, must be studied near the site of production. They must be produced with charged-particle beams at accelerators rather than via neutron capture. The use of radioactive heavy actinide targets is often required and the number of atoms produced is so small that any chemistry to be performed must be done on an ''atom-at-a-time'' basis. Furthermore, a knowledge of their nuclear properties is required in order to identify and detect them. To date, both gas and aqueous phase properties of elements as heavy as element 104 (rutherfordium) and element 105 (hahnium) have been investigated, even though their longest-lived known isotopes have half-lives of only 65 and 35 seconds, respectively. The experimental results show that their chemical properties cannot be simply extrapolated from the known properties of their lighter homologs in the periodic table, emphasizing the importance of obtaining additional experimental information for the heaviest elements to compare with predictions and help assess the influence of relativistic effects. The feasibility of the extension of chemical studies to still heavier elements is also discussed. (orig.)

  2. Hydrogen in CANDU fuel elements

    International Nuclear Information System (INIS)

    Sejnoha, R.; Manzer, A.M.; Surette, B.A.

    1995-01-01

    Unirradiated and irradiated CANDU fuel cladding was tested to compare the role of stress-corrosion cracking and of hydrogen in the development of fuel defects. The results of the tests are compared with information on fuel performance in-reactor. The role of hydriding (deuteriding) from the coolant and from the fuel element inside is discussed, and the control of 'hydrogen gas' content in the element is confirmed as essential for defect-free fuel performance. Finally, implications for fuel element design are discussed. (author)

  3. Origin of the chemical elements

    Energy Technology Data Exchange (ETDEWEB)

    Tayler, R J

    1984-05-01

    The subject is discussed in relation to the composition of initially created matter and changes which have occurred during the life history of the universe, with particular reference to our galaxy and nearby galaxies. Headings are: observations of element abundances (stars, gas clouds in our own and nearby galaxies, hot gas in galaxy clusters, the solar system); the originally created matter (Big Bang theory and early nuclear reactions); processes changing observed composition (galactic evolution; nuclear fusion reactions in stellar interiors; chemical composition of a highly evolved massive star); supernovae (production of heavy elements); chemical evolution of the galaxy; production of very heavy elements (s process, r process).

  4. Increased burnup of fuel elements

    International Nuclear Information System (INIS)

    Ahlf, J.

    1983-01-01

    The specialists' group for fuel elements of the Kerntechnische Gesellschaft e.V. held a meeting on ''Increased Burnup of Fuel Elements'' on 9th and 10th of November 1982 at the GKSS Research Center Geesthacht. Most papers dealt with the problems of burnup increase of fuel elements for light water reactors with respect to fuel manufacturing, power plant operation and reprocessing. Review papers were given on the burnup limits for high temperature gas cooled reactors and sodium fast breeder reactors. The meeting ended with a presentation of the technical equipment of the hot laboratory of the GKSS and the programs which are in progress there. (orig.) [de

  5. Prebiotic synthesis of histidine

    Science.gov (United States)

    Shen, C.; Yang, L.; Miller, S. L.; Oro, J.

    1990-01-01

    The prebiotic formation of histidine (His) has been accomplished experimentally by the reaction of erythrose with formamidine followed by a Strecker synthesis. In the first step of this reaction sequence, the formation of imidazole-4-acetaldehyde took place by the condensation of erythrose and formamidine, two compounds that are known to be formed under prebiotic conditions. In a second step, the imidazole-4-acetaldehyde was converted to His, without isolation of the reaction products by adding HCN and ammonia to the reaction mixture. LC, HPLC, thermospray liquid chromatography-mass spectrometry, and tandem mass spectrometry were used to identify the product, which was obtained in a yield of 3.5% based on the ratio of His/erythrose. This is a new chemical synthesis of one of the basic amino acids which had not been synthesized prebiotically until now.

  6. Voice synthesis application

    Science.gov (United States)

    Lightstone, P. C.; Davidson, W. M.

    1982-04-01

    The military detection assessment laboratory houses an experimental field system which assesses different alarm indicators such as fence disturbance sensors, MILES cables, and microwave Racons. A speech synthesis board which could be interfaced, by means of a computer, to an alarm logger making verbal acknowledgement of alarms possible was purchased. Different products and different types of voice synthesis were analyzed before a linear predictive code device produced by Telesensory Speech Systems of Palo Alto, California was chosen. This device is called the Speech 1000 Board and has a dedicated 8085 processor. A multiplexer card was designed and the Sp 1000 interfaced through the card into a TMS 990/100M Texas Instrument microcomputer. It was also necessary to design the software with the capability of recognizing and flagging an alarm on any 1 of 32 possible lines. The experimental field system was then packaged with a dc power supply, LED indicators, speakers, and switches, and deployed in the field performing reliably.

  7. Benzoylurea Chitin Synthesis Inhibitors.

    Science.gov (United States)

    Sun, Ranfeng; Liu, Chunjuan; Zhang, Hao; Wang, Qingmin

    2015-08-12

    Benzoylurea chitin synthesis inhibitors are widely used in integrated pest management (IPM) and insecticide resistance management (IRM) programs due to their low toxicity to mammals and predatory insects. In the past decades, a large number of benzoylurea derivatives have been synthesized, and 15 benzoylurea chitin synthesis inhibitors have been commercialized. This review focuses on the history of commercial benzolyphenylureas (BPUs), synthetic methods, structure-activity relationships (SAR), action mechanism research, environmental behaviors, and ecotoxicology. Furthermore, their disadvantages of high risk to aquatic invertebrates and crustaceans are pointed out. Finally, we propose that the para-substituents at anilide of benzoylphenylureas should be the functional groups, and bipartite model BPU analogues are discussed in an attempt to provide new insight for future development of BPUs.

  8. Function of SREBP1 in the Milk Fat Synthesis of Dairy Cow Mammary Epithelial Cells

    Directory of Open Access Journals (Sweden)

    Nan Li

    2014-09-01

    Full Text Available Sterol regulatory element-binding proteins (SREBPs belong to a family of nuclear transcription factors. The question of which is the most important positive regulator in milk fat synthesis in dairy cow mammary epithelial cells (DCMECs between SREBPs or other nuclear transcription factors, such as peroxisome proliferator-activated receptor γ (PPARγ, remains a controversial one. Recent studies have found that mTORC1 (the mammalian target of rapamycin C1 regulates SREBP1 to promote fat synthesis. Thus far, however, the interaction between the SREBP1 and mTOR (the mammalian target of rapamycin pathways in the regulation of milk fat synthesis remains poorly understood. This study aimed to identify the function of SREBP1 in milk fat synthesis and to characterize the relationship between SREBP1 and mTOR in DCMECs. The effects of SREBP1 overexpression and gene silencing on milk fat synthesis and the effects of stearic acid and serum on SREBP1 expression in the upregulation of milk fat synthesis were investigated in DCMECs using immunostaining, Western blotting, real-time quantitative PCR, lipid droplet staining, and detection kits for triglyceride content. SREBP1 was found to be a positive regulator of milk fat synthesis and was shown to be regulated by stearic acid and serum. These findings indicate that SREBP1 is the key positive regulator in milk fat synthesis.

  9. Phase contrast image synthesis

    DEFF Research Database (Denmark)

    Glückstad, J.

    1996-01-01

    A new method is presented for synthesizing arbitrary intensity patterns based on phase contrast imaging. The concept is grounded on an extension of the Zernike phase contrast method into the domain of full range [0; 2 pi] phase modulation. By controlling the average value of the input phase funct...... function and by choosing appropriate phase retardation at the phase contrast filter, a pure phase to intensity imaging is accomplished. The method presented is also directly applicable in dark field image synthesis....

  10. synthesis and structures

    Indian Academy of Sciences (India)

    Priya Saxena

    2017-08-29

    Aug 29, 2017 ... to a single crystal X-ray diffraction study for 1, 2 and 4-7. Keywords. Sterically .... 2.2b Mono-Schiff base 2: A suspension of I (1.00 g,. 2.27 mmol) and ...... bridge Crystallographic Data Centre, CCDC, 12 Union. Road, Cambridge .... H-C 2014 Rational design and synthesis of porous poly- mer networks: ...

  11. Distributed PROMPT-LTL Synthesis

    Directory of Open Access Journals (Sweden)

    Swen Jacobs

    2016-09-01

    Full Text Available We consider the synthesis of distributed implementations for specifications in Prompt Linear Temporal Logic (PROMPT-LTL, which extends LTL by temporal operators equipped with parameters that bound their scope. For single process synthesis it is well-established that such parametric extensions do not increase worst-case complexities. For synchronous systems, we show that, despite being more powerful, the distributed realizability problem for PROMPT-LTL is not harder than its LTL counterpart. For asynchronous systems we have to consider an assume-guarantee synthesis problem, as we have to express scheduling assumptions. As asynchronous distributed synthesis is already undecidable for LTL, we give a semi-decision procedure for the PROMPT-LTL assume-guarantee synthesis problem based on bounded synthesis.

  12. Elemental balance in soy sauce

    International Nuclear Information System (INIS)

    Haruyama, Yoichi; Saito, Manabu; Yoshida, Koji.

    1996-01-01

    We have measured the elemental concentrations of soy sauce and its actual raw materials which are used in a certain soy sauce factory. In the present measurement, we measured de-fatted soybean, wheat and salt as raw materials and soy sauce and soy sauce waste as final products. Five kinds of elements, such as Mn, Fe, Cu, Zn and Br, were detected. We obtained elemental concentrations of them except for Mn in each materials. The measured elemental concentration in soy sauce agreed well each other with the calculated one within the experimental errors using the measured concentration in the raw materials and their weight in actual producing process. Contrary to our expectation, it was found that wheat contributes to soy sauce bromine concentration dominantly in the present case. (author)

  13. Elements of Tiny Plasma Spectrometers

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to advance major elements of a miniaturized plasma spectrometer for flight on future missions. This type of instrument has been developed and successfully...

  14. Finite element computational fluid mechanics

    International Nuclear Information System (INIS)

    Baker, A.J.

    1983-01-01

    This book analyzes finite element theory as applied to computational fluid mechanics. It includes a chapter on using the heat conduction equation to expose the essence of finite element theory, including higher-order accuracy and convergence in a common knowledge framework. Another chapter generalizes the algorithm to extend application to the nonlinearity of the Navier-Stokes equations. Other chapters are concerned with the analysis of a specific fluids mechanics problem class, including theory and applications. Some of the topics covered include finite element theory for linear mechanics; potential flow; weighted residuals/galerkin finite element theory; inviscid and convection dominated flows; boundary layers; parabolic three-dimensional flows; and viscous and rotational flows

  15. Nuclear reactor fuel element assemblies

    International Nuclear Information System (INIS)

    Krawiec, D.M.; Bevilacqua, F.

    1974-01-01

    The fuel elements of each fuel element group are separated from each other by means of a multitude of thin, intersecting plates in the from of grid strips. Flow deflectors near the surface of the fuel elements are used in order to make the coolant flow more turbulent. They are designed as vanes and arranged at a distance on the grid strips. Each deflector vane has two arms stretching in opposite directions, each one into a neighbouring channel. In outward direction, the deflector vanes are converging. The strips with the vanes can be put on the supporting grid of the fuel elements. The vane structure can be reinforced by providing distortions in the strip material near the vanes. (DG) [de

  16. Elemental ABAREX -- a user's manual

    International Nuclear Information System (INIS)

    Smith, A.B.

    1999-01-01

    ELEMENTAL ABAREX is an extended version of the spherical optical-statistical model code ABAREX, designed for the interpretation of neutron interactions with elemental targets consisting of up to ten isotopes. The contributions from each of the isotopes of the element are explicitly dealt with, and combined for comparison with the elemental observables. Calculations and statistical fitting of experimental data are considered. The code is written in FORTRAN-77 and arranged for use on the IBM-compatible personal computer (PC), but it should operate effectively on a number of other systems, particularly VAX/VMS and IBM work stations. Effort is taken to make the code user friendly. With this document a reasonably skilled individual should become fluent with the use of the code in a brief period of time

  17. The evolution of the elements

    International Nuclear Information System (INIS)

    Williams, P.M.

    1978-01-01

    It is believed that only the lightest elements, hydrogen and helium, were created during the 'Big Bang' origin of the Universe and that all heavier elements were synthesized by nuclear reactions in stars, the interstellar medium and possibly in 'little bangs' in the nuclei of galaxies. The composition of the interstellar medium has evolved through enrichment by processed material shed by evolving stars and the composition of the Solar System reflects that of the interstellar medium at the time of its formation. Differentiation processes during the evolution of the Solar System and individual planets account for the different compositions of the Sun and the planets. The measurement of the abundance distribution of the elements has become a very powerful tool in the elucidation of the evolution of the Solar System, stars and the Galaxy. This review attempts to trace the formation of the elements in stars and their subsequent evolution. (author)

  18. Environmental research on actinide elements

    International Nuclear Information System (INIS)

    Pinder, J.E. III; Alberts, J.J.; McLeod, K.W.; Schreckhise, R.G.

    1987-08-01

    The papers synthesize the results of research sponsored by DOE's Office of Health and Environmental Research on the behavior of transuranic and actinide elements in the environment. Separate abstracts have been prepared for the 21 individual papers

  19. Electromagnetic matrix elements in baryons

    International Nuclear Information System (INIS)

    Lipkin, H.J.; Moinester, M.A.

    1992-01-01

    Some simple symmetry relations between matrix elements of electromagnetic operators are investigated. The implications are discussed for experiments to study hyperon radiative transitions and polarizabilities and form factors. (orig.)

  20. Integrated methanol synthesis

    International Nuclear Information System (INIS)

    Jaeger, W.

    1982-01-01

    This invention concerns a plant for methanol manufacture from gasified coal, particularly using nuclear power. In order to reduce the cost of the hydrogen circuits, the methanol synthesis is integrated in the coal gasification plant. The coal used is gasified with hydration by means of hydrogen and the crude gas emerging, after cooling and separating the carbon dioxide and hydrogen sulphide, is mixed with the synthetic gas leaving the methane cracking furnace. This mixture is taken to the methanol synthesis and more than 90% is converted into methanol in one pass. The gas mixture remaning after condensation and separation of methanol is decomposed into three fractions in low temperature gas decomposition with a high proportion of unconverted carbon monoxide. The flow of methane is taken to the cracking furnace with steam, the flow of hydrogen is taken to the hydrating coal gasifier, and the flow of carbon monoxide is taken to the methanol synthesis. The heat required for cracking the methane can either be provided by a nuclear reactor or by the coke left after hydrating gasification. (orig./RB) [de

  1. Gold Nanoparticle Microwave Synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Krantz, Kelsie E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Christian, Jonathan H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Coopersmith, Kaitlin [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Washington, II, Aaron L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Murph, Simona H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-07-27

    At the nanometer scale, numerous compounds display different properties than those found in bulk material that can prove useful in areas such as medicinal chemistry. Gold nanoparticles, for example, display promise in newly developed hyperthermia therapies for cancer treatment. Currently, gold nanoparticle synthesis is performed via the hot injection technique which has large variability in final particle size and a longer reaction time. One underdeveloped area by which these particles could be produced is through microwave synthesis. To initiate heating, microwaves agitate polar molecules creating a vibration that gives off the heat energy needed. Previous studies have used microwaves for gold nanoparticle synthesis; however, polar solvents were used that partially absorbed incident microwaves, leading to partial thermal heating of the sample rather than taking full advantage of the microwave to solely heat the gold nanoparticle precursors in a non-polar solution. Through this project, microwaves were utilized as the sole heat source, and non-polar solvents were used to explore the effects of microwave heating only as pertains to the precursor material. Our findings show that the use of non-polar solvents allows for more rapid heating as compared to polar solvents, and a reduction in reaction time from 10 minutes to 1 minute; this maximizes the efficiency of the reaction, and allows for reproducibility in the size/shape of the fabricated nanoparticles.

  2. Chemistry of Ammonothermal Synthesis

    Directory of Open Access Journals (Sweden)

    Theresia M. M. Richter

    2014-02-01

    Full Text Available Ammonothermal synthesis is a method for synthesis and crystal growth suitable for a large range of chemically different materials, such as nitrides (e.g., GaN, AlN, amides (e.g., LiNH2, Zn(NH22, imides (e.g., Th(NH2, ammoniates (e.g., Ga(NH33F3, [Al(NH36]I3 · NH3 and non-nitrogen compounds like hydroxides, hydrogen sulfides and polychalcogenides (e.g., NaOH, LiHS, CaS, Cs2Te5. In particular, large scale production of high quality crystals is possible, due to comparatively simple scalability of the experimental set-up. The ammonothermal method is defined as employing a heterogeneous reaction in ammonia as one homogenous fluid close to or in supercritical state. Three types of milieus may be applied during ammonothermal synthesis: ammonobasic, ammononeutral or ammonoacidic, evoked by the used starting materials and mineralizers, strongly influencing the obtained products. There is little known about the dissolution and materials transport processes or the deposition mechanisms during ammonothermal crystal growth. However, the initial results indicate the possible nature of different intermediate species present in the respective milieus.

  3. Gold Nanoparticle Microwave Synthesis

    International Nuclear Information System (INIS)

    Krantz, Kelsie E.; Christian, Jonathan H.; Coopersmith, Kaitlin; Washington II, Aaron L.; Murph, Simona H.

    2016-01-01

    At the nanometer scale, numerous compounds display different properties than those found in bulk material that can prove useful in areas such as medicinal chemistry. Gold nanoparticles, for example, display promise in newly developed hyperthermia therapies for cancer treatment. Currently, gold nanoparticle synthesis is performed via the hot injection technique which has large variability in final particle size and a longer reaction time. One underdeveloped area by which these particles could be produced is through microwave synthesis. To initiate heating, microwaves agitate polar molecules creating a vibration that gives off the heat energy needed. Previous studies have used microwaves for gold nanoparticle synthesis; however, polar solvents were used that partially absorbed incident microwaves, leading to partial thermal heating of the sample rather than taking full advantage of the microwave to solely heat the gold nanoparticle precursors in a non-polar solution. Through this project, microwaves were utilized as the sole heat source, and non-polar solvents were used to explore the effects of microwave heating only as pertains to the precursor material. Our findings show that the use of non-polar solvents allows for more rapid heating as compared to polar solvents, and a reduction in reaction time from 10 minutes to 1 minute; this maximizes the efficiency of the reaction, and allows for reproducibility in the size/shape of the fabricated nanoparticles.

  4. Programming the finite element method

    CERN Document Server

    Smith, I M; Margetts, L

    2013-01-01

    Many students, engineers, scientists and researchers have benefited from the practical, programming-oriented style of the previous editions of Programming the Finite Element Method, learning how to develop computer programs to solve specific engineering problems using the finite element method. This new fifth edition offers timely revisions that include programs and subroutine libraries fully updated to Fortran 2003, which are freely available online, and provides updated material on advances in parallel computing, thermal stress analysis, plasticity return algorithms, convection boundary c

  5. Pipeline robots with elastic elements

    Directory of Open Access Journals (Sweden)

    A. Matuliauskas

    2002-10-01

    Full Text Available In the article constructions of the pipeline robots with elastic elements are reviewed and the scheme of new original construction is presented. The mathematical models of a robot with one-dimensional vibration exciter with two degrees of freedom were developed and the equations of movement were formed and written. The mathematical model of the pipeline robot with circular elements is formed and its motion equations are presented.

  6. ELEMENTS OF SAFETY IN PARAGLIDING

    OpenAIRE

    Janez Mekinc; Katarina Mušič

    2016-01-01

    Paragliding is an opportunity for tourism development, depending on what position the sport has place in the local community, the restrictions for paragliders and the safety components of the region. The paper explores the phenomenon of paragliding and safety elements in the Upper Soča region, one of ten best paragliding sites in the world (Placestoseeinyourlifetime, 2015). The purpose of the research is to analyse the safety elements, the development and the risk of paragliding.The goals of ...

  7. Fuel element box inspection device

    International Nuclear Information System (INIS)

    Ortmayer, R.M.; Pick, W.

    1985-01-01

    The invention concerns a device for inspecting the outer geometry of a long fuel element box by measuring the surface contours over its longitudinal crossection and along its length by sensors. These are kept in a sledge which can be moved along the fuel element guide in a slot guide. The measurement signals reach an evaluation device outside the longitudinal box. (orig./HP) [de

  8. Nuclear fuel elements and assemblies

    International Nuclear Information System (INIS)

    Saito, Shozo; Maki, Hideo.

    1982-01-01

    Purpose: To facilitate the attainment of the uranium enrichment or gadolinia enrichment of a pellet filled in a fuel element. Constitution: The axial length of a pellet filled in a fuel element is set to predetermined sizes according to the uranium enrichment factor, gadolinia enrichment or their combination. Thus, the uranium enrichment factor or gadolinia enrichment can be identified by attaining the axial length of the pellet by using such a pellt. (Kamimura, M.)

  9. Nuclear reactor fuel element splitter

    International Nuclear Information System (INIS)

    Yeo, D.

    1976-01-01

    A method and apparatus are disclosed for removing nuclear fuel from a clad fuel element. The fuel element is power driven past laser beams which simultaneously cut the cladding lengthwise into at least two longitudinal pieces. The axially cut lengths of cladding are then separated, causing the nuclear fuel contained therein to drop into a receptacle for later disposition. The cut lengths of cladding comprise nuclear waste which is disposed of in a suitable manner. 6 claims, 10 drawing figures

  10. Phase diagrams of the elements

    International Nuclear Information System (INIS)

    Young, D.A.

    1975-01-01

    A summary of the pressure-temperature phase diagrams of the elements is presented, with graphs of the experimentally determined solid-solid phase boundaries and melting curves. Comments, including theoretical discussion, are provided for each diagram. The crystal structure of each solid phase is identified and discussed. This work is aimed at encouraging further experimental and theoretical research on phase transitions in the elements

  11. Nuclear chemistry of transactinide elements

    Energy Technology Data Exchange (ETDEWEB)

    Nagame, Yuichiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1997-07-01

    The current status on the nuclear chemistry studies of transactinide elements is reviewed. The production of transactinides in heavy ion reactions is briefly discussed, and nuclear properties on the stability of transactinides are presented. Chemical properties of the trans-actinide elements 104, 105 and 106, and a typical experimental technique used to study these properties on an atom-at-a-time base are introduced. (author)

  12. Chemistry of the transactinide elements

    International Nuclear Information System (INIS)

    Schaedel, M.

    1995-01-01

    The experimentally known chemical properties of the transactinide elements 104 and 105, and the experimental techniques used to study these properties on an atom-at-a-time base, are reviewed. The production of transactinides in heavy ion reactions and the specific aspects of chemical separations with single atoms is briefly discussed. The chemical properties of the first two transactinide elements are compared with the lighter element homologs in group 4 and 5 of the Periodic Table and with the expected behaviour obtained from most recent atomic and molecular calculations which take the increasingly strong relativistic effect into account. Elements 104 and 105 behave as transactinide elements and, in general, exhibit properties characteristic of their position in group 4 and 5 of the Periodic Table. However, surprising deviations of the chemical properties from expectations based on simple extrapolations have been observed. It is shown that the chemical properties of the heaviest elements cannot reliably be predicted by simple extrapolations. Prospects to extend our chemical knowledge at the top end of the Periodic Table are discussed. (orig.)

  13. Feature-aware natural texture synthesis

    KAUST Repository

    Wu, Fuzhang; Dong, Weiming; Kong, Yan; Mei, Xing; Yan, Dongming; Zhang, Xiaopeng; Paul, Jean Claude

    2014-01-01

    This article presents a framework for natural texture synthesis and processing. This framework is motivated by the observation that given examples captured in natural scene, texture synthesis addresses a critical problem, namely, that synthesis

  14. New elements - approaching Z=114

    International Nuclear Information System (INIS)

    Hofmann, S.

    1998-03-01

    The search for new elements is part of the broader field of investigations of nuclei at the limits of stability. In two series of experiments at SHIP, six new elements (Z=107-112) were synthesized via fusion reactions using 1n-deexcitation channels and lead or bismuth targets. The isotopes were unambiguously identified by means of α-α correlations. Not fission, but alpha decay is the dominant decay mode. The collected decay data establish a means of comparison with theoretical data. This aids in the selection of appropriate models that describe the properties of known nuclei. Predictions based on these models are useful in the preparation of the next generation of experiments. Cross-sections decrease by two orders of magnitude from bohrium (Z=107) to element 112, for which a cross-section of 1 pb was measured. The development of intense beam currents and sensitive detection methods is essential for the production and identification of still heavier elements and new isotopes of already known elements, as well as the measurement of small α-, β- and fission-branching ratios. An equally sensitive set-up is needed for the measurement of excitation functions at low cross-sections. Based on our results, it is likely that the production of isotopes of element 114 close to the island of spherical super heavy elements (SHE) could be achieved by fusion reactions using 208 Pb targets. Systematic studies of the reaction cross-sections indicate that the transfer of nucleons is an important process for the initiation of fusion. The data allow for the fixing of a narrow energy window for the production of SHE using 1n-emission channels. (orig.)

  15. Hard template synthesis of metal nanowires

    Directory of Open Access Journals (Sweden)

    Go eKawamura

    2014-11-01

    Full Text Available Metal nanowires (NWs have attracted much attention because of their high electron conductivity, optical transmittance and tunable magnetic properties. Metal NWs have been synthesized using soft templates such as surface stabilizing molecules and polymers, and hard templates such as anodic aluminum oxide, mesoporous oxide, carbon nanotubes. NWs prepared from hard templates are composites of metals and the oxide/carbon matrix. Thus, selecting appropriate elements can simplify the production of composite devices. The resulting NWs are immobilized and spatially arranged, as dictated by the ordered porous structure of the template. This avoids the NWs from aggregating, which is common for NWs prepared with soft templates in solution. Herein, the hard template synthesis of metal NWs is reviewed, and the resulting structures, properties and potential applications are discussed.

  16. Hard template synthesis of metal nanowires

    Science.gov (United States)

    Kawamura, Go; Muto, Hiroyuki; Matsuda, Atsunori

    2014-11-01

    Metal nanowires (NWs) have attracted much attention because of their high electron conductivity, optical transmittance and tunable magnetic properties. Metal NWs have been synthesized using soft templates such as surface stabilizing molecules and polymers, and hard templates such as anodic aluminum oxide, mesoporous oxide, carbon nanotubes. NWs prepared from hard templates are composites of metals and the oxide/carbon matrix. Thus, selecting appropriate elements can simplify the production of composite devices. The resulting NWs are immobilized and spatially arranged, as dictated by the ordered porous structure of the template. This avoids the NWs from aggregating, which is common for NWs prepared with soft templates in solution. Herein, the hard template synthesis of metal NWs is reviewed, and the resulting structures, properties and potential applications are discussed.

  17. Synthesis of functional materials in combustion reactions

    Science.gov (United States)

    Zhuravlev, V. D.; Bamburov, V. G.; Ermakova, L. V.; Lobachevskaya, N. I.

    2015-12-01

    The conditions for obtaining oxide compounds in combustion reactions of nitrates of metals with organic chelating-reducing agents such as amino acids, urea, and polyvinyl alcohol are reviewed. Changing the nature of internal fuels and the reducing agent-to-oxidizing agent ratio makes possible to modify the thermal regime of the process, fractal dimensionality, morphology, and dispersion of synthesized functional materials. This method can be used to synthesize simple and complex oxides, composites, and metal powders, as well as ceramics and coatings. The possibilities of synthesis in combustion reactions are illustrated by examples of αand γ-Al2O3, YSZ composites, uranium oxides, nickel powder, NiO and NiO: YSZ composite, TiO2, and manganites, cobaltites, and aluminates of rare earth elements.

  18. Manufacturing Demonstration Facility: Low Temperature Materials Synthesis

    International Nuclear Information System (INIS)

    Graham, David E.; Moon, Ji-Won; Armstrong, Beth L.; Datskos, Panos G.; Duty, Chad E.; Gresback, Ryan; Ivanov, Ilia N.; Jacobs, Christopher B.; Jellison, Gerald Earle; Jang, Gyoung Gug; Joshi, Pooran C.; Jung, Hyunsung; Meyer, Harry M.; Phelps, Tommy

    2015-01-01

    The Manufacturing Demonstration Facility (MDF) low temperature materials synthesis project was established to demonstrate a scalable and sustainable process to produce nanoparticles (NPs) for advanced manufacturing. Previous methods to chemically synthesize NPs typically required expensive, high-purity inorganic chemical reagents, organic solvents and high temperatures. These processes were typically applied at small laboratory scales at yields sufficient for NP characterization, but insufficient to support roll-to-roll processing efforts or device fabrication. The new NanoFermentation processes described here operated at a low temperature (~60 C) in low-cost, aqueous media using bacteria that produce extracellular NPs with controlled size and elemental stoichiometry. Up-scaling activities successfully demonstrated high NP yields and quality in a 900-L pilot-scale reactor, establishing this NanoFermentation process as a competitive biomanufacturing strategy to produce NPs for advanced manufacturing of power electronics, solid-state lighting and sensors.

  19. Facile Synthesis of Ternary Boron Carbonitride Nanotubes

    Directory of Open Access Journals (Sweden)

    Luo Lijie

    2009-01-01

    Full Text Available Abstract In this study, a novel and facile approach for the synthesis of ternary boron carbonitride (B–C–N nanotubes was reported. Growth occurred by heating simple starting materials of boron powder, zinc oxide powder, and ethanol absolute at 1150 °C under a mixture gas flow of nitrogen and hydrogen. As substrate, commercial stainless steel foil with a typical thickness of 0.05 mm played an additional role of catalyst during the growth of nanotubes. The nanotubes were characterized by SEM, TEM, EDX, and EELS. The results indicate that the synthesized B–C–N nanotubes exhibit a bamboo-like morphology and B, C, and N elements are homogeneously distributed in the nanotubes. A catalyzed vapor–liquid–solid (VLS mechanism was proposed for the growth of the nanotubes.

  20. Manufacturing Demonstration Facility: Low Temperature Materials Synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Graham, David E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moon, Ji-Won [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Armstrong, Beth L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Datskos, Panos G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Duty, Chad E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gresback, Ryan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ivanov, Ilia N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jacobs, Christopher B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jellison, Gerald Earle [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jang, Gyoung Gug [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Joshi, Pooran C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jung, Hyunsung [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Meyer, III, Harry M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Phelps, Tommy [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-06-30

    The Manufacturing Demonstration Facility (MDF) low temperature materials synthesis project was established to demonstrate a scalable and sustainable process to produce nanoparticles (NPs) for advanced manufacturing. Previous methods to chemically synthesize NPs typically required expensive, high-purity inorganic chemical reagents, organic solvents and high temperatures. These processes were typically applied at small laboratory scales at yields sufficient for NP characterization, but insufficient to support roll-to-roll processing efforts or device fabrication. The new NanoFermentation processes described here operated at a low temperature (~60 C) in low-cost, aqueous media using bacteria that produce extracellular NPs with controlled size and elemental stoichiometry. Up-scaling activities successfully demonstrated high NP yields and quality in a 900-L pilot-scale reactor, establishing this NanoFermentation process as a competitive biomanufacturing strategy to produce NPs for advanced manufacturing of power electronics, solid-state lighting and sensors.

  1. Finite element modeling of piezoelectric elements with complex electrode configuration

    International Nuclear Information System (INIS)

    Paradies, R; Schläpfer, B

    2009-01-01

    It is well known that the material properties of piezoelectric materials strongly depend on the state of polarization of the individual element. While an unpolarized material exhibits mechanically isotropic material properties in the absence of global piezoelectric capabilities, the piezoelectric material properties become transversally isotropic with respect to the polarization direction after polarization. Therefore, for evaluating piezoelectric elements the material properties, including the coupling between the mechanical and the electromechanical behavior, should be addressed correctly. This is of special importance for the micromechanical description of piezoelectric elements with interdigitated electrodes (IDEs). The best known representatives of this group are active fiber composites (AFCs), macro fiber composites (MFCs) and the radial field diaphragm (RFD), respectively. While the material properties are available for a piezoelectric wafer with a homogeneous polarization perpendicular to its plane as postulated in the so-called uniform field model (UFM), the same information is missing for piezoelectric elements with more complex electrode configurations like the above-mentioned ones with IDEs. This is due to the inhomogeneous field distribution which does not automatically allow for the correct assignment of the material, i.e. orientation and property. A variation of the material orientation as well as the material properties can be accomplished by including the polarization process of the piezoelectric transducer in the finite element (FE) simulation prior to the actual load case to be investigated. A corresponding procedure is presented which automatically assigns the piezoelectric material properties, e.g. elasticity matrix, permittivity, and charge vector, for finite element models (FEMs) describing piezoelectric transducers according to the electric field distribution (field orientation and strength) in the structure. A corresponding code has been

  2. Synthesis and characterization of innovative insulation materials

    Directory of Open Access Journals (Sweden)

    Skaropoulou Aggeliki

    2018-01-01

    Full Text Available Insulation elements are distinguished in inorganic fibrous and organic foamed materials. Foamed insulation materials are of great acceptance and use, but their major disadvantage is their flammability. In case of fire, they tend to transmit the flame producing toxic gases. In this paper, the synthesis and characterization of innovative inorganic insulation materials with properties competitive to commercial is presented. Their synthesis involves the mixing of inorganic raw material and water with reinforcing agent or/and foaming agent leading to the formation of a gel. Depending on raw materials nature, the insulation material is produced by freeze drying or ambient drying techniques of the gel. The raw material used are chemically benign and abundantly available materials, or industrial by-products and the final products are non-toxic and, in some cases, non-flammable. Their density and thermal conductivity was measured and found 0.02-0.06 g/cm3 and 0.03-0.04 W/mK, respectively.

  3. Enzymatic Synthesis of Biobased Polyesters and Polyamides

    Directory of Open Access Journals (Sweden)

    Yi Jiang

    2016-06-01

    Full Text Available Nowadays, “green” is a hot topic almost everywhere, from retailers to universities to industries; and achieving a green status has become a universal aim. However, polymers are commonly considered not to be “green”, being associated with massive energy consumption and severe pollution problems (for example, the “Plastic Soup” as a public stereotype. To achieve green polymers, three elements should be entailed: (1 green raw materials, catalysts and solvents; (2 eco-friendly synthesis processes; and (3 sustainable polymers with a low carbon footprint, for example, (biodegradable polymers or polymers which can be recycled or disposed with a gentle environmental impact. By utilizing biobased monomers in enzymatic polymerizations, many advantageous green aspects can be fulfilled. For example, biobased monomers and enzyme catalysts are renewable materials that are derived from biomass feedstocks; enzymatic polymerizations are clean and energy saving processes; and no toxic residuals contaminate the final products. Therefore, synthesis of renewable polymers via enzymatic polymerizations of biobased monomers provides an opportunity for achieving green polymers and a future sustainable polymer industry, which will eventually play an essential role for realizing and maintaining a biobased and sustainable society.

  4. Mapping student thinking in chemical synthesis

    Science.gov (United States)

    Weinrich, Melissa

    In order to support the development of learning progressions about central ideas and practices in different disciplines, we need detailed analyses of the implicit assumptions and reasoning strategies that guide students' thinking at different educational levels. In the particular case of chemistry, understanding how new chemical substances are produced (chemical synthesis) is of critical importance. Thus, we have used a qualitative research approach based on individual interviews with first semester general chemistry students (n = 16), second semester organic chemistry students (n = 15), advanced undergraduates (n = 9), first year graduate students (n = 15), and PhD candidates (n = 16) to better characterize diverse students' underlying cognitive elements (conceptual modes and modes of reasoning) when thinking about chemical synthesis. Our results reveal a great variability in the cognitive resources and strategies used by students with different levels of training in the discipline to make decisions, particularly at intermediate levels of expertise. The specific nature of the task had a strong influence on the conceptual sophistication and mode of reasoning that students exhibited. Nevertheless, our data analysis has allowed us to identify common modes of reasoning and assumptions that seem to guide students' thinking at different educational levels. Our results should facilitate the development of learning progressions that help improve chemistry instruction, curriculum, and assessment.

  5. Synthesis and intramolecular cyclizationof thiosemicarbazide morpholilacetic acid

    Directory of Open Access Journals (Sweden)

    Moldyr Dyusebaeva

    2015-12-01

    Full Text Available The paper gives details on the synthesis of four new, potentially biologically active compounds based on amorpholineheterocycle structure. By alkylation of morpholine with ethyl bromoacetate, a morfolilacetic acid ethyl ester was synthesized. Its reaction with hydrazine hydrate led to the hydrazide. We developed the method for synthesis and studied cyclization of thiosemicarbazide morfolilaceticacidin in alkaline medium with formation of bisgeterocyclic system. The possibility of the existence of this compound in two tautomeric forms: thione and thiol, i.e. a 3- (1'-morpholyl-methyl -1,2,4-triazole-5-thione and 3- (1-morpholyl-1'-methyl -5-mercapto-1,2,4-triazole was described. In neutral medium, one product was obtained. According to spectral data, it is attributed to the structure of 3-(1'-morpholil-methyl-1,2,4-triazole-5-thione. Structure of newly synthesized compounds is confirmed by IR and 1H-NMR spectra and data of elemental analysis. These compounds are potentially biologically active substances and are promising for further research.

  6. A Software Architecture for Intelligent Synthesis Environments

    Science.gov (United States)

    Filman, Robert E.; Norvig, Peter (Technical Monitor)

    2001-01-01

    The NASA's Intelligent Synthesis Environment (ISE) program is a grand attempt to develop a system to transform the way complex artifacts are engineered. This paper discusses a "middleware" architecture for enabling the development of ISE. Desirable elements of such an Intelligent Synthesis Architecture (ISA) include remote invocation; plug-and-play applications; scripting of applications; management of design artifacts, tools, and artifact and tool attributes; common system services; system management; and systematic enforcement of policies. This paper argues that the ISA extend conventional distributed object technology (DOT) such as CORBA and Product Data Managers with flexible repositories of product and tool annotations and "plug-and-play" mechanisms for inserting "ility" or orthogonal concerns into the system. I describe the Object Infrastructure Framework, an Aspect Oriented Programming (AOP) environment for developing distributed systems that provides utility insertion and enables consistent annotation maintenance. This technology can be used to enforce policies such as maintaining the annotations of artifacts, particularly the provenance and access control rules of artifacts-, performing automatic datatype transformations between representations; supplying alternative servers of the same service; reporting on the status of jobs and the system; conveying privileges throughout an application; supporting long-lived transactions; maintaining version consistency; and providing software redundancy and mobility.

  7. Brain trace elements and aging

    International Nuclear Information System (INIS)

    Hebbrecht, Geert; Maenhaut, Willy; Reuck, Jacques de

    1999-01-01

    Degenerative mechanisms involved in the aging process of the brain are to a certain extent counteracted by repair mechanisms. In both degenerative and recovery processes, trace elements are involved. The present study focused on the role of two minor (i.e., K and Ca) and six trace elements (i.e., Mn, Fe, Cu, Zn, Se and Rb) in the aging process. The elements were determined by PIXE in cerebral cortex and white matter, basal ganglia, brainstem and cerebellar cortex of 18 postmortem human brains, from persons without a history of neurologic or psychiatric disease who deceased between the age of 7 and 79. This age range allowed us to study the relationship between elemental concentrations and age. The most prominent findings were a concentration decrease for K and Rb and a concentration increase for the elements Ca, Fe, Zn and Se. The study supports recent findings that Ca and Fe are involved in brain degenerative processes initiated by oxygen free radicals, whereas Zn and Se are involved in immunological reactions counteracting the aging process

  8. Radiochemical synthesis of etomoxir

    Energy Technology Data Exchange (ETDEWEB)

    Abbas, Hafiz G. [Institute of Nuclear Medicine and Oncology (INMOL), New Campus Road, Lahore (Pakistan); Yunus, M. [University of the Punjab, New Campus Road, Lahore (Pakistan); Feinendegen, Ludwig E., E-mail: feinendegen@gmx.ne [Department of Nuclear Medicine, Heinrich-Heine University Duesseldorf, Wannental 45, 88131 Lindau (Germany)

    2011-02-15

    Sodium 2-{l_brace}6-(4-chlorophenoxy)hexyl{r_brace}oxirane-2-carboxylate (Etomoxir) inhibits transport of fatty acids via the carnitine shuttle into mitochondria of muscle cells and prevents long chain fatty acids from providing energy through {beta}-oxidation especially for muscle contraction. The objective of this synthesis is to develop a method for radioiodination of Etomoxir in order to explore its potential in diagnostic metabolic studies and molecular imaging. Thus, a method is described for the radiochemical synthesis and purification of ethyl 2-{l_brace}6-(4-[{sup 131}I]iodophenoxy)hexyl{r_brace}oxirane-2-carboxylate (3) and 2-{l_brace}6-(4-[{sup 131}I]iodo-phenoxy)hexyl{r_brace}oxirane-2-carboxylic acid (4). For the synthesis of these new agents, ethyl 2-{l_brace}6-(4-bromophenoxy)hexyl{r_brace}oxirane-2-carboxylate (1) and 2-{l_brace}6-(4-bromophenoxy)hexyl{r_brace}oxirane-2-carboxylic acid (2) were refluxed with [{sup 131}I]NaI in the presence of anhydrous acetone at a temperature of 80 {sup o}C and 90 {sup o}C for a period of 3-4 hours, respectively. The method of radiolabeling, based on the nucleophilic exchange reaction, resulted in a radiochemical yield of 43% and 67% for compounds 3 and 4, respectively. This paper reports on the labeling of etomoxir with radioiodine as {sup 124}I labeled etomoxir may be of great importance in molecular imaging.

  9. Evidence synthesis software.

    Science.gov (United States)

    Park, Sophie Elizabeth; Thomas, James

    2018-06-07

    It can be challenging to decide which evidence synthesis software to choose when doing a systematic review. This article discusses some of the important questions to consider in relation to the chosen method and synthesis approach. Software can support researchers in a range of ways. Here, a range of review conditions and software solutions. For example, facilitating contemporaneous collaboration across time and geographical space; in-built bias assessment tools; and line-by-line coding for qualitative textual analysis. EPPI-Reviewer is a review software for research synthesis managed by the EPPI-centre, UCL Institute of Education. EPPI-Reviewer has text mining automation technologies. Version 5 supports data sharing and re-use across the systematic review community. Open source software will soon be released. EPPI-Centre will continue to offer the software as a cloud-based service. The software is offered via a subscription with a one-month (extendible) trial available and volume discounts for 'site licences'. It is free to use for Cochrane and Campbell reviews. The next EPPI-Reviewer version is being built in collaboration with National Institute for Health and Care Excellence using 'surveillance' of newly published research to support 'living' iterative reviews. This is achieved using a combination of machine learning and traditional information retrieval technologies to identify the type of research each new publication describes and determine its relevance for a particular review, domain or guideline. While the amount of available knowledge and research is constantly increasing, the ways in which software can support the focus and relevance of data identification are also developing fast. Software advances are maximising the opportunities for the production of relevant and timely reviews. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise

  10. Fuel element tomography by gammametry

    International Nuclear Information System (INIS)

    Simonet, G.; Pineira, T.

    1982-03-01

    As from transversal gamma determinations of a cylindrical fuel element, the TOMOGAM program reconstitutes the distribution of fission products in a section. This direct, fast and non destructive method, makes it possible to have access to the behaviour of the fuel at any time: - the soluble fission products in the matrix represent the fuel itself and the distribution of the fissions, - the migrating elements inform on the temperature reached in accordance with the permitted powers, - the volatile nuclides build up in particular points where physical-chemical phenomena of fuel-cladding interaction are liable to corrode the latter. Hence, gamma spectrometry extends its possibilities of analysis relative to the performance of reactor elements [fr

  11. Physical model of Nernst element

    International Nuclear Information System (INIS)

    Nakamura, Hiroaki; Ikeda, Kazuaki; Yamaguchi, Satarou

    1998-08-01

    Generation of electric power by the Nernst effect is a new application of a semiconductor. A key point of this proposal is to find materials with a high thermomagnetic figure-of-merit, which are called Nernst elements. In order to find candidates of the Nernst element, a physical model to describe its transport phenomena is needed. As the first model, we began with a parabolic two-band model in classical statistics. According to this model, we selected InSb as candidates of the Nernst element and measured their transport coefficients in magnetic fields up to 4 Tesla within a temperature region from 270 K to 330 K. In this region, we calculated transport coefficients numerically by our physical model. For InSb, experimental data are coincident with theoretical values in strong magnetic field. (author)

  12. [Trace elements of bone tumors].

    Science.gov (United States)

    Kalashnikov, V M; Zaĭchik, V E; Bizer, V A

    1983-01-01

    Due to activation analysis involving the use of neutrons from a nuclear reactor, the concentrations of 11 trace elements: scandium, iron, cobalt, mercury, rubidium, selenium, silver, antimony, chrome, zinc and terbium in intact bone and skeletal tumors were measured. 76 specimens of bioptates and resected material of operations for bone tumors and 10 specimens of normal bone tissue obtained in autopsies of cases of sudden death were examined. The concentrations of trace elements and their dispersion patterns in tumor tissue were found to be significantly higher than those in normal bone tissue. Also, the concentrations of some trace elements in tumor differed significantly from those in normal tissue; moreover, they were found to depend on the type and histogenesis of the neoplasm.

  13. Marine oligotrophy and element biogeochemistry

    International Nuclear Information System (INIS)

    Jeffree, R.A.; Szymczak, R.

    1999-01-01

    A biogeochemical model has been developed that explains the inverse and non-linear relationship between Po-210 concentration in zooplankton and their biomass, under oligotrophic conditions in French Polynesia. This study identified other elements with comparable accumulatory behaviours to Po-210 in phytoplankton, seston and zooplankton, that are proposed to be critical to its enhanced environmental levels under oligotrophy. Field investigation in the Gulf of Papua showed that four of these a priori identified elements viz Cd, Co, Pb and Mn, as well as Cr and Ni, showed elevated water concentrations with reduced biological productivity, results that are consistent with those previously obtained for Po-210 and the proposed explanatory model. These findings point to the enhanced susceptibility of oligotrophic systems to contamination from particle-reactive elements. (author)

  14. Lactobacillusassisted synthesis of titanium nanoparticles

    Directory of Open Access Journals (Sweden)

    Jha Anal

    2007-01-01

    Full Text Available AbstractAn eco-friendlylactobacillussp. (microbe assisted synthesis of titanium nanoparticles is reported. The synthesis is performed at room temperature. X-ray and transmission electron microscopy analyses are performed to ascertain the formation of Ti nanoparticles. Individual nanoparticles as well as a number of aggregates almost spherical in shape having a size of 40–60 nm are found.

  15. Organic synthesis with stable isotopes

    International Nuclear Information System (INIS)

    Blazer, R.M.; Daub, G.H.; Kerr, V.N.; Williams, D.L.; Whaley, T.W.

    1982-01-01

    Described is a scheme for the synthesis of L-arginine-1- 13 C utilizing methods developed for the synthesis of L-ornithine-1- 13 C from L-ornithine-2- 13 C and then converting ornithine into arginine with the enzyme acylase

  16. A novel synthesis of hemispherands

    NARCIS (Netherlands)

    Ostaszewski, Ryszard; Verboom, Willem; Reinhoudt, David

    1992-01-01

    A novel, flexible synthesis of hemispherands {2,5,8-trioxa[9](3,3″) m-terphenylophanes 5a-d} with different central aromatic groups is described. The key step comprises the introduction of the central aromatic ring in the last step of the synthesis via a Suzuki cross-coupling reaction using

  17. First total synthesis of Boehmenan

    Indian Academy of Sciences (India)

    The first total synthesis of dilignan Boehmenan has been achieved. A biomimetic oxidative coupling of the ferulic acid methyl ester in the presence of silver oxide is the crucial step in the synthesis sequence, generating the dihydrobenzofuran skeleton. Hydroxyl group was protected with DHP and reducted with LiAlH4 to ...

  18. Chemical synthesis on SU-8

    DEFF Research Database (Denmark)

    Qvortrup, Katrine; Taveras, Kennedy; Thastrup, Ole

    2011-01-01

    In this paper we describe a highly effective surface modification of SU-8 microparticles, the attachment of appropriate linkers for solid-supported synthesis, and the successful chemical modification of these particles via controlled multi-step organic synthesis leading to molecules attached...

  19. FINITE ELEMENT ANALYSIS OF ELEMENT ANALYSIS OF A FREE ...

    African Journals Online (AJOL)

    eobe

    the stairs and to compare the finite element ana ... tual three dimensional behavior of the stair slab system. ..... due to its close relation of output with the propo .... flights. It is best not to consider any open well when .... thermodynamics of solids.

  20. Learning via Query Synthesis

    KAUST Repository

    Alabdulmohsin, Ibrahim Mansour

    2017-05-07

    Active learning is a subfield of machine learning that has been successfully used in many applications. One of the main branches of active learning is query synthe- sis, where the learning agent constructs artificial queries from scratch in order to reveal sensitive information about the underlying decision boundary. It has found applications in areas, such as adversarial reverse engineering, automated science, and computational chemistry. Nevertheless, the existing literature on membership query synthesis has, generally, focused on finite concept classes or toy problems, with a limited extension to real-world applications. In this thesis, I develop two spectral algorithms for learning halfspaces via query synthesis. The first algorithm is a maximum-determinant convex optimization method while the second algorithm is a Markovian method that relies on Khachiyan’s classical update formulas for solving linear programs. The general theme of these methods is to construct an ellipsoidal approximation of the version space and to synthesize queries, afterward, via spectral decomposition. Moreover, I also describe how these algorithms can be extended to other settings as well, such as pool-based active learning. Having demonstrated that halfspaces can be learned quite efficiently via query synthesis, the second part of this thesis proposes strategies for mitigating the risk of reverse engineering in adversarial environments. One approach that can be used to render query synthesis algorithms ineffective is to implement a randomized response. In this thesis, I propose a semidefinite program (SDP) for learning a distribution of classifiers, subject to the constraint that any individual classifier picked at random from this distributions provides reliable predictions with a high probability. This algorithm is, then, justified both theoretically and empirically. A second approach is to use a non-parametric classification method, such as similarity-based classification. In this

  1. Total Synthesis of Hyperforin.

    Science.gov (United States)

    Ting, Chi P; Maimone, Thomas J

    2015-08-26

    A 10-step total synthesis of the polycyclic polyprenylated acylphloroglucinol (PPAP) natural product hyperforin from 2-methylcyclopent-2-en-1-one is reported. This route was enabled by a diketene annulation reaction and an oxidative ring expansion strategy designed to complement the presumed biosynthesis of this complex meroterpene. The described work enables the preparation of a highly substituted bicyclo[3.3.1]nonane-1,3,5-trione motif in only six steps and thus serves as a platform for the construction of easily synthesized, highly diverse PPAPs modifiable at every position.

  2. Dibutylphosphoric acid synthesis

    International Nuclear Information System (INIS)

    Elias, H.; Boumaout, R.; Kellou, N.; Amedjkouh, A.; Hamidi, A.

    1995-09-01

    This work consists on the synthesis of dibutylphosphoric acis (DBP) by reaction of butanol with phosphorus pentoxid and on its separation by liquid-liquid extraction. It also deals with the characterization of DBP by some physicochemical analysis methods such as : chromatography, pH-metry and infrared and ultraviolet spectrophotometries. this study showed essentialy, that DBP can be formed in an appreciable amount (55%) when the reaction is realised with butanol/pentoxid molar ratio upper than 3 at temperature of 95 C

  3. Microemulsion Synthesis of Nanoparticles

    Directory of Open Access Journals (Sweden)

    Gotić, M.

    2013-11-01

    Full Text Available Nanoparticles and nanomaterials have wide applications in electronics, physics, material design, being also utilized as sensors, catalysts, and more and more in biomedicine. Microemulsions are an exceptionally suitable medium for the synthesis of nanoparticles due to their thermodynamical stability, great solubility of both polar and nonpolar components, as well as their ability to control the size, dispersity and shape of the particles. This review presents microemulsion techniques for the synthesis of inorganic nanoparticles. It takes place in water-in-oil microemulsions by mixing one microemulsion with a cationic precursor, and the other with a precipitating or reducing agent, or by direct addition of reducing agents or gas (O2, NH3 ili CO2 into microemul sion (Fig. 1. Metal nanoparticles are used as catalysts, sensors, ferrofluids etc. They are produced by reducing the metal cation with a suitable reducing agent. In a similar way, one can prepare nanoparticles of alloys from the metal salts, provided that the metals are mutually soluble. The microemulsion technique is also suitable for depositing nanoparticles onto various surfaces. Highly active catalysts made from nanoparticles of Pt, Pd, Rh and other noble metals may be obtained in this way. Metal oxides and hydroxides may be prepared by hydrolysis or precipitation in the water core of microemulsion. Precipitation can be initiated by adding the base or precipitating agent into the microemulsion with water solution of metal ions. Similarly, nanoparticles may be prepared of sulphides, halogenides, cyanides, carbonates, sulphates and other insoluble metal salts. To prevent oxidation of nanoparticles, especially Fe, the particles are coated with inert metals, oxides, various polymers etc. Coating may provide additional functionality; e.g. coating with gold allows subsequent functionalization with organic compounds containing sulphur, due to the strong Au–S bond. Polymer coatings decrease

  4. Introducing the "Human Element" in Chemistry by Synthesizing Blue Pigments and Creating Cyanotypes in a First-Year Chemistry Course

    Science.gov (United States)

    Morizot, Olivier; Audureau, Eric; Briend, Jean-Yves; Hagel, Gaetan; Boulc'h, Florence

    2015-01-01

    In this article, we present two concrete applications of the concept of the human element to chemistry education; starting with a course and experimental project on blue pigment synthesis and concluding with cross-disciplinary lessons and experiments on blue photography. In addition to the description of the content of these courses, we explore…

  5. Synthesis of 3-Methyl-1-morpholin-4-ylmethyl-2,6-diphenylpiperidin-4-one

    Directory of Open Access Journals (Sweden)

    Bathey R. Venkatraman

    2009-09-01

    Full Text Available This paper describes the synthesis of 3-methyl-1-morpholin-4-ylmethyl-2,6-diphenylpiperidin-4-one from 3-methyl-2,6-diphenylpiperidin-4-one. The synthesized compound was characterized by FT-IR, 1H NMR, EI-MS and elemental analysis.

  6. Multiple-diffusion flame synthesis of pure anatase and carbon-coated titanium dioxide nanoparticles

    KAUST Repository

    Memon, Nasir; Anjum, Dalaver H.; Chung, Suk-Ho

    2013-01-01

    A multi-element diffusion flame burner (MEDB) is useful in the study of flame synthesis of nanomaterials. Here, the growth of pure anatase and carbon-coated titanium dioxide (TiO2) using an MEDB is demonstrated. Hydrogen (H2), oxygen (O2), and argon

  7. One-pot efficient green synthesis of 1,4-dihydro-quinoxaline-2,3 ...

    Indian Academy of Sciences (India)

    Unknown

    Thermal and powder X-ray diffraction analysis was carried out for some hydrated crystals. Keywords. Green chemistry ... Elemental analyses were done using Carlo–Erba 1108 and Perkin–Elmer series II 2400 instruments. 2.3 General synthesis of quinoxaline derivatives ... with a pestle in a mortar at room temperature in an.

  8. Status of transuranium element production

    International Nuclear Information System (INIS)

    King, L.J.

    1985-01-01

    The Transuranium Processing Plant at Oak Ridge National Laboratory has been the production, storage, and distribution center for the heavy-element research program of the US Department of Energy since 1966. During the past four years, annual production rates of transcurium elements have been relatively stable, averaging 34 mg of 249 Bk, 369 mg of 252 Cf, 1.4 mg of 253 Es, and 0.7 pg of 257 Fm. The extensive provisions for changing and modifying equipment have allowed continual updating of the plant to include new concepts in chemical processes and equipment design. 21 refs., 4 figs., 2 tabs

  9. Transposable elements and circular DNAs

    KAUST Repository

    Mourier, Tobias

    2016-09-26

    Circular DNAs are extra-chromosomal fragments that become circularized by genomic recombination events. We have recently shown that yeast LTR elements generate circular DNAs through recombination events between their flanking long terminal repeats (LTRs). Similarly, circular DNAs can be generated by recombination between LTRs residing at different genomic loci, in which case the circular DNA will contain the intervening sequence. In yeast, this can result in gene copy number variations when circles contain genes and origins of replication. Here, I speculate on the potential and implications of circular DNAs generated through recombination between human transposable elements.

  10. Elements to diminish radioactive accidents

    International Nuclear Information System (INIS)

    Cortes I, M.E.; Ramirez G, F.P.

    1998-01-01

    In this work it is presented an application of the cause-effect diagram method or Ichikawa method identifying the elements that allow to diminish accidents when the radioactive materials are transported. It is considered the transport of hazardous materials which include radioactive materials in the period: December 1996 until March 1997. Among the identified elements by this method it is possible to mention: the road type, the radioactive source protection, the grade driver responsibility and the preparation that the OEP has in the radioactive material management. It is showed the differences found between the country inner roads and the Mexico City area. (Author)

  11. Quality assurance of fuel elements

    International Nuclear Information System (INIS)

    Hoerber, J.

    1980-01-01

    The quality assurance activities for reactor fuel elements are based on a quality assurance system which implies the requirements resulting from the specifications, regulations of the authorities, national standards and international rules and regulations. The quality assurance related to production of reactor fuel will be shown for PWR fuel elements in all typical fabrication steps as conversion into UO 2 -powder, pelletizing, rodmanufacture and assembling. A wide range of destructive and nondestructive techniques is applied. Quality assurance is not only verified by testing techniques but also by process monitoring by means of parameter control in production and testing procedures. (RW)

  12. Elements of spatial data quality

    CERN Document Server

    Guptill, SC

    1995-01-01

    Elements of Spatial Data Quality outlines the need and suggests potential categories for the content of a comprehensive statement of data quality that must be imbedded in the metadata that accompanies the transfer of a digital spatial data file or is available in a separate metadata catalog. Members of the International Cartographic Association's Commission on Spatial Data Quality have identified seven elements of data quality: positional accuracy, attribute accuracy, completeness, logical consistency, lineage, semantic accuracy and temporal information. In the book the authors describe: compo

  13. Chemistry of the heaviest elements

    International Nuclear Information System (INIS)

    Schaedel, M.

    1992-08-01

    The experimentally known chemical properties of elements 103,104, and 105, and the experimental techniques to obtain these properties on a one-atom- at-a-time base, are summarized. The chemical properties are compared with the lighter group 3,4 and 5 homologs and with the expected behaviour as obtained from theoretical calculations. In this transition region from the last actinide element to the beginning of the transactinide series one may expect to find evidence for increasingly strong relativistic effects altering the chemical behaviour. (orig.)

  14. FINITE ELEMENT ANALYSIS OF STRUCTURES

    Directory of Open Access Journals (Sweden)

    PECINGINA OLIMPIA-MIOARA

    2015-05-01

    Full Text Available The application of finite element method is analytical when solutions can not be applied for deeper study analyzes static, dynamic or other types of requirements in different points of the structures .In practice it is necessary to know the behavior of the structure or certain parts components of the machine under the influence of certain factors static and dynamic . The application of finite element in the optimization of components leads to economic growth , to increase reliability and durability organs studied, thus the machine itself.

  15. Transposable elements and circular DNAs

    KAUST Repository

    Mourier, Tobias

    2016-01-01

    Circular DNAs are extra-chromosomal fragments that become circularized by genomic recombination events. We have recently shown that yeast LTR elements generate circular DNAs through recombination events between their flanking long terminal repeats (LTRs). Similarly, circular DNAs can be generated by recombination between LTRs residing at different genomic loci, in which case the circular DNA will contain the intervening sequence. In yeast, this can result in gene copy number variations when circles contain genes and origins of replication. Here, I speculate on the potential and implications of circular DNAs generated through recombination between human transposable elements.

  16. Trace elements in human pituitary

    International Nuclear Information System (INIS)

    Kanabrocki, E.L.; Greco, J.; Graham, L.A.; Kaplan, E.; Rubnitz, M.E.; Oester, Y.T.; Brar, S.; Gustafson, P.S.; Nelson, D.M.; Molinari, F.; Moore, C.E.; Kanabrocki, J.A.

    1976-01-01

    Neutron activation analysis was used to determine several trace elements in human pituitaries from adult subjects aged 42 to 83 years who had died of ischemic heart disease, carcinoma and cirrhosis of the liver. None of these subjects suffered from mental disease. The concentrations of Fe, Zn, Rb, Se, Br, Cr, Hg, Cs and Co in dried tissue showed no correlation with the diseases, and the results may therefore be representative of the general population. These elements may play a very fundamental role in pituitary function. (U.K.)

  17. Nuclear fuel element end fitting

    International Nuclear Information System (INIS)

    Jabsen, F.S.

    1979-01-01

    A typical embodiment of the invention has an array of sockets that are welded to the intersections of the plates that form the upper and lower end fittings of a nuclear reactor fuel element. The sockets, which are generally cylindrical in shape, are oriented in directions that enable the longitudinal axes of the sockets to align with the longitudinal axes of the fuel rods that are received in the respective sockets. Detents impressed in the surfaces of the sockets engage mating grooves that are formed in the ends of the fuel rods to provide for the structural integrity of the fuel element

  18. Finite elements of nonlinear continua

    CERN Document Server

    Oden, John Tinsley

    1972-01-01

    Geared toward undergraduate and graduate students, this text extends applications of the finite element method from linear problems in elastic structures to a broad class of practical, nonlinear problems in continuum mechanics. It treats both theory and applications from a general and unifying point of view.The text reviews the thermomechanical principles of continuous media and the properties of the finite element method, and then brings them together to produce discrete physical models of nonlinear continua. The mathematical properties of these models are analyzed, along with the numerical s

  19. Synthesis of lever-blade dampers with enhanced mechanical structure

    Directory of Open Access Journals (Sweden)

    Igor I. Sydorenko

    2015-03-01

    Full Text Available Since the torsion bar represents just an elastic element, the energy dissipation in suspensions problem is highly relevant for its application. Currently in quality of a dissipation device in torsion suspension are used the hydraulic dampers with movable members reciprocating translational motion respectively to the housing or lever-type hydraulic shock absorbers of piston and vane types, with the movable member’s rotational movement respectively to the housing. These dampers are implementing only throttle-valve performance type, associated with these devices’ functional capacities and depending on design constraints. The paper presents a synthesis of innovative lever-blade dampers, whose performance is not related to the value of working chambers inner pressure. Their essential peculiarity relates to the mechanical control loop presence in the structure that determines a close relationship between the performance and the value of the shock absorber movable element displacement relatively to the body. In the process of synthesis carried out tested are the appropriate methods, built on the basis of technical systems’ modeling with modified kinematic graphs. The synthesis results are shown in the form of two structurally implemented samples. Performed is a comparative analysis of the samples with their basic performance determining.

  20. Synthesis and tribological properties of antimony N, N-diethanoldithiocarbamate

    Institute of Scientific and Technical Information of China (English)

    李丽; 黄可龙; 瞿龙; 舒万艮

    2001-01-01

    Antimony N, N-diethanoldithiocarbamate was synthesized with diethanolamine, antimony trioxide and carbon disulfide. The influences of temperature, reaction time, solvents and their dosages were investigated, and the optimum synthesis conditions were: reaction temperature 15~20 ℃, reaction time 2.5 h, 250 mL CH3OH as solvent and the hot CH3OH as recrystallization solvent. Element analysis, IR, 1HNMR and 13CNMR spectra were used to study its chemical composition and molecular structure. Antimony N, N-diethanol-dithiocarbamate was added in the base oil, and its properties of wear resistance and extreme pressure were studied by FB, FD and WSD. The synthesis product behaves per fectly as wear resistance and extreme pressure additive and its extreme pressure property is superior to its wear resistance property. The mechanism of tribological action was discussed by using XPS and AES spectra, and the reason of good wear resistance and extreme pressure properties is that the synthesis product decompose element C, S and N.

  1. Mixed Element Formulation for the Finite Element-Boundary Integral Method

    National Research Council Canada - National Science Library

    Meese, J; Kempel, L. C; Schneider, S. W

    2006-01-01

    A mixed element approach using right hexahedral elements and right prism elements for the finite element-boundary integral method is presented and discussed for the study of planar cavity-backed antennas...

  2. Nuclear fuel elements design, fabrication and performance

    CERN Document Server

    Frost, Brian R T

    1982-01-01

    Nuclear Fuel Elements: Design, Fabrication and Performance is concerned with the design, fabrication, and performance of nuclear fuel elements, with emphasis on fast reactor fuel elements. Topics range from fuel types and the irradiation behavior of fuels to cladding and duct materials, fuel element design and modeling, fuel element performance testing and qualification, and the performance of water reactor fuels. Fast reactor fuel elements, research and test reactor fuel elements, and unconventional fuel elements are also covered. This volume consists of 12 chapters and begins with an overvie

  3. Spectroscopic Analyses of Neutron Capture Elements in Open Clusters

    Science.gov (United States)

    O'Connell, Julia E.

    The evolution of elements as a function or age throughout the Milky Way disk provides strong constraints for galaxy evolution models, and on star formation epochs. In an effort to provide such constraints, we conducted an investigation into r- and s-process elemental abundances for a large sample of open clusters as part of an optical follow-up to the SDSS-III/APOGEE-1 near infrared survey. To obtain data for neutron capture abundance analysis, we conducted a long-term observing campaign spanning three years (2013-2016) using the McDonald Observatory Otto Struve 2.1-meter telescope and Sandiford Cass Echelle Spectrograph (SES, R(lambda/Deltalambda) ˜60,000). The SES provides a wavelength range of ˜1400 A, making it uniquely suited to investigate a number of other important chemical abundances as well as the neutron capture elements. For this study, we derive abundances for 18 elements covering four nucleosynthetic families- light, iron-peak, neutron capture and alpha-elements- for ˜30 open clusters within 6 kpc of the Sun with ages ranging from ˜80 Myr to ˜10 Gyr. Both equivalent width (EW) measurements and spectral synthesis methods were employed to derive abundances for all elements. Initial estimates for model stellar atmospheres- effective temperature and surface gravity- were provided by the APOGEE data set, and then re-derived for our optical spectra by removing abundance trends as a function of excitation potential and reduced width log(EW/lambda). With the exception of Ba II and Zr I, abundance analyses for all neutron capture elements were performed by generating synthetic spectra from the new stellar parameters. In order to remove molecular contamination, or blending from nearby atomic features, the synthetic spectra were modeled by a best-fit Gaussian to the observed data. Nd II shows a slight enhancement in all cluster stars, while other neutron capture elements follow solar abundance trends. Ba II shows a large cluster-to-cluster abundance spread

  4. Music therapy in dementia: a narrative synthesis systematic review.

    Science.gov (United States)

    McDermott, Orii; Crellin, Nadia; Ridder, Hanne Mette; Orrell, Martin

    2013-08-01

    Recent reviews on music therapy for people with dementia have been limited to attempting to evaluate whether it is effective, but there is a need for a critical assessment of the literature to provide insight into the possible mechanisms of actions of music therapy. This systematic review uses a narrative synthesis format to determine evidence for effectiveness and provide insight into a model of action. The narrative synthesis framework consists of four elements: (i) theory development; (ii) preliminary synthesis of findings; (iii) exploration of relationships between studies; and (iv) assessment of the robustness of the synthesis. Electronic and hand searches identified 263 potentially relevant studies. Eighteen studies met the full inclusion criteria. Three distinctive strands of investigations emerged: eight studies explored behavioural and psychological aspects, five studies investigated hormonal and physiological changes, and five studies focused on social and relational aspects of music therapy. The musical interventions in the studies were diverse, but singing featured as an important medium for change. Evidence for short-term improvement in mood and reduction in behavioural disturbance was consistent, but there were no high-quality longitudinal studies that demonstrated long-term benefits of music therapy. Future music therapy studies need to define a theoretical model, include better-focused outcome measures, and discuss how the findings may improve the well-being of people with dementia. Copyright © 2012 John Wiley & Sons, Ltd.

  5. A multi-paradigm language for reactive synthesis

    Directory of Open Access Journals (Sweden)

    Ioannis Filippidis

    2016-02-01

    Full Text Available This paper proposes a language for describing reactive synthesis problems that integrates imperative and declarative elements. The semantics is defined in terms of two-player turn-based infinite games with full information. Currently, synthesis tools accept linear temporal logic (LTL as input, but this description is less structured and does not facilitate the expression of sequential constraints. This motivates the use of a structured programming language to specify synthesis problems. Transition systems and guarded commands serve as imperative constructs, expressed in a syntax based on that of the modeling language Promela. The syntax allows defining which player controls data and control flow, and separating a program into assumptions and guarantees. These notions are necessary for input to game solvers. The integration of imperative and declarative paradigms allows using the paradigm that is most appropriate for expressing each requirement. The declarative part is expressed in the LTL fragment of generalized reactivity(1, which admits efficient synthesis algorithms, extended with past LTL. The implementation translates Promela to input for the Slugs synthesizer and is written in Python. The AMBA AHB bus case study is revisited and synthesized efficiently, identifying the need to reorder binary decision diagrams during strategy construction, in order to prevent the exponential blowup observed in previous work.

  6. Synthesis of Lipidated Proteins.

    Science.gov (United States)

    Mejuch, Tom; Waldmann, Herbert

    2016-08-17

    Protein lipidation is one of the major post-translational modifications (PTM) of proteins. The attachment of the lipid moiety frequently determines the localization and the function of the lipoproteins. Lipidated proteins participate in many essential biological processes in eukaryotic cells, including vesicular trafficking, signal transduction, and regulation of the immune response. Malfunction of these cellular processes usually leads to various diseases such as cancer. Understanding the mechanism of cellular signaling and identifying the protein-protein and protein-lipid interactions in which the lipoproteins are involved is a crucial task. To achieve these goals, fully functional lipidated proteins are required. However, access to lipoproteins by means of standard expression is often rather limited. Therefore, semisynthetic methods, involving the synthesis of lipidated peptides and their subsequent chemoselective ligation to yield full-length lipoproteins, were developed. In this Review we summarize the commonly used methods for lipoprotein synthesis and the development of the corresponding chemoselective ligation techniques. Several key studies involving full-length semisynthetic lipidated Ras, Rheb, and LC3 proteins are presented.

  7. Ethylene and protein synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Osborne, D J

    1973-01-01

    Ethylene reduces the rate of expansion growth of cells and it is suggestive that the rate of expansion is controlled at least in part by the synthesis of hydroxyproline rich glycopeptides that are secreted with other polysaccharide material through the plasmalemma into the cell wall, thereby enhancing the thickness of the cell wall and also rendering it poorly extensible. In combination, auxin would appear to counteract the effect of ethylene in this respect, for although auxin enhances the synthesis of protein and the content in the cell walls, as well as causing some increase in wall thickness, it reduces the amount of hydroxyproline reaching the wall. Such effects may be instrumental in enhancing wall plasticity, the rate of expansion and the final cell size. These results indicate that ethylene and auxin together afford a dual regulatory system exerted through a control of a specific part of the protein synthetic pathway, the products of which regulate the rate of expansion, and the potential for expansion, of the plant cell wall. 38 references, 3 figures, 8 tables.

  8. Sterol regulatory element-binding protein-1 participates in the regulation of fatty acid synthase expression in colorectal neoplasia.

    Science.gov (United States)

    Li, J N; Mahmoud, M A; Han, W F; Ripple, M; Pizer, E S

    2000-11-25

    Endogenous fatty acid synthesis has been observed in certain rapidly proliferating normal and neoplastic tissues. Sterol regulatory element-binding proteins (SREBPs) are transcription factors that regulate the expression of lipogenic genes including fatty acid synthase (FAS), the major biosynthetic enzyme for fatty acid synthesis. We have previously shown that SREBP-1, FAS, and Ki-67, a proliferation marker, colocalized in the crypts of the fetal gastrointestinal tract epithelium. This study sought to determine whether SREBP-1 participates in the regulation of proliferation-associated fatty acid synthesis in colorectal neoplasia. An immunohistochemical analysis of SREBP-1, FAS, and Ki-67 expression in 25 primary human colorectal carcinoma specimens showed colocalization in 22 of these. To elucidate a functional linkage between SREBP-1 activation and proliferation-associated FA synthesis, SREBP-1 and FAS content were assayed during the adaptive response of cultured HCT116 colon carcinoma cells to pharmacological inhibition of FA synthesis. Cerulenin and TOFA each inhibited the endogenous synthesis of fatty acids in a dose-dependent manner and each induced increases in both precursor and mature forms of SREBP-1. Subsequently, both the transcriptional activity of the FAS promoter in a luciferase reporter gene construct and the FAS expression increased. These results demonstrate that tumor cells recognize and respond to a deficiency in endogenous fatty acid synthesis by upregulating both SREBP-1 and FAS expression and support the model that SREBP-1 participates in the transcriptional regulation of lipogenic genes in colorectal neoplasia. Copyright 2000 Academic Press.

  9. Proceedings of the workshop on the nuclear sciences of the heaviest elements

    Energy Technology Data Exchange (ETDEWEB)

    Nagame, Yuichiro; Haba, Hiromitsu; Ikezoe, Hiroshi [eds.

    2000-03-01

    The workshop on the nuclear sciences of the heaviest elements took place on July 21-22, 1999 at the Japan Atomic Energy Research Institute (JAERI), Tokai. Approximately 40 scientists and 15 graduate students participated in the workshop which was organized by the Advanced Science Research Center, JAERI. The successful syntheses of three new super-heavy elements in 1999, Z=114 at the Joint Institute for Nuclear Research in Dubna, Russia, and Z=118 (with Z=116 following from {alpha}-decay of Z=118) at the Lawrence Berkeley National Laboratory (LBNL) in USA, are tremendous progress in the field of the heavy element research. The 1st International Conference on the Chemistry and Physics of the Transactinide Elements (TAN99) was held in Germany from September 26 to 30, 1999 to discuss in a larger context all scientific aspects of the heaviest elements. Thus, it was timely to hold the present domestic workshop to summarize what has been done in recent years, to see what has come true, and to discuss the perspectives in the near feature. The subjects in the workshop were classified into; (1) synthesis of heavy elements, (2) decay properties of heavy nuclei, (3) chemistry of the heaviest elements, and (4) future plans of the heavy element research in Japan. This volume contains the papers presented in the workshop. The 14 papers are indexed individually. (J.P.N.)

  10. Environmental research on actinide elements

    Energy Technology Data Exchange (ETDEWEB)

    Pinder, J.E. III; Alberts, J.J.; McLeod, K.W.; Schreckhise, R.G. (eds.)

    1987-08-01

    The papers synthesize the results of research sponsored by DOE's Office of Health and Environmental Research on the behavior of transuranic and actinide elements in the environment. Separate abstracts have been prepared for the 21 individual papers. (ACR)

  11. Extrachromosomal genetic elements in Micrococcus.

    Science.gov (United States)

    Dib, Julián Rafael; Liebl, Wolfgang; Wagenknecht, Martin; Farías, María Eugenia; Meinhardt, Friedhelm

    2013-01-01

    Micrococci are Gram-positive G + C-rich, nonmotile, nonspore-forming actinomycetous bacteria. Micrococcus comprises ten members, with Micrococcus luteus being the type species. Representatives of the genus play important roles in the biodegradation of xenobiotics, bioremediation processes, production of biotechnologically important enzymes or bioactive compounds, as test strains in biological assays for lysozyme and antibiotics, and as infective agents in immunocompromised humans. The first description of plasmids dates back approximately 28 years, when several extrachromosomal elements ranging in size from 1.5 to 30.2 kb were found in Micrococcus luteus. Up to the present, a number of circular plasmids conferring antibiotic resistance, the ability to degrade aromatic compounds, and osmotolerance are known, as well as cryptic elements with unidentified functions. Here, we review the Micrococcus extrachromosomal traits reported thus far including phages and the only quite recently described large linear extrachromosomal genetic elements, termed linear plasmids, which range in size from 75 kb (pJD12) to 110 kb (pLMA1) and which confer putative advantageous capabilities, such as antibiotic or heavy metal resistances (inferred from sequence analyses and curing experiments). The role of the extrachromosomal elements for the frequently proven ecological and biotechnological versatility of the genus will be addressed as well as their potential for the development and use as genetic tools.

  12. Trace elements in brazilian soils

    International Nuclear Information System (INIS)

    Rocha, Geraldo Cesar

    1995-01-01

    A literature revision on trace elements (Zn, B, Mn, Mo, Cu, Fe, and Cl) in Brazilian soils was prepared, with special attention to the chemical form and range in the soil, extraction methods and correlation of the amount in soils with soil properties

  13. Fuel element database: developer handbook

    International Nuclear Information System (INIS)

    Dragicevic, M.

    2004-09-01

    The fuel elements database which was developed for Atomic Institute of the Austrian Universities is described. The software uses standards like HTML, PHP and SQL. For the standard installation freely available software packages such as MySQL database or the PHP interpreter from Apache Software Foundation and Java Script were used. (nevyjel)

  14. FOIL ELEMENT FOR NUCLEAR REACTOR

    Science.gov (United States)

    Noland, R.A.; Walker, D.E.; Spinrad, B.I.

    1963-07-16

    A method of making a foil-type fuel element is described. A foil of fuel metal is perforated in; regular design and sheets of cladding metal are placed on both sides. The cladding metal sheets are then spot-welded to each other through the perforations, and the edges sealed. (AEC)

  15. Automatic welding of fuel elements

    International Nuclear Information System (INIS)

    Briola, J.

    1958-01-01

    The welding process depends on the type of fuel element, the can material and the number of cartridges to be welded: - inert-gas welding (used for G2 and the 1. set of EL3), - inert atmosphere arc welding (used for welding uranium and zirconium), - electronic welding (used for the 2. set of EL3 and the tank of Proserpine). (author) [fr

  16. Treatment of incorporated transuranium elements

    International Nuclear Information System (INIS)

    Volf, V.

    1978-01-01

    The text of this report and its tables and figures provide basic information on the decorporation of transuranium elements as well as an insight into the more general principles, trends and interactions. The detailed tables and the exhaustive list of important references should enable the reader to make his own conclusions in a minimum of time

  17. Pyrochemical properties of actinides elements

    International Nuclear Information System (INIS)

    Akabori, Mitsuo; Hayashi, Hirokazu; Minato, Kazuo

    2005-01-01

    The present status of research works on pyrochemical processing is introduced in view of: 1) the process concept; 2) R and D progress; 3) new experimental facilities in NUCEF. Basic laboratory studies with rare-earth elements have almost been completed and hot tests with americium have been started at the TRU-HITEC facility in NUCEF. (author)

  18. Backfire antennas with dipole elements

    DEFF Research Database (Denmark)

    Nielsen, Erik Dragø; Pontoppidan, Knud

    1970-01-01

    A method is set up for a theoretical investigation of arbitrary backfire antennas based upon dipole structures. The mutual impedance between the dipole elements of the antenna is taken into account, and the field radiated due to a surface wave reflector of finite extent is determined by calculating...

  19. The relationship of element contents in erythrocyte with thyroid function

    International Nuclear Information System (INIS)

    Zhu Li; Zhao Zhiying; Wang Zhenghua; Li Yanfen; Liu Nianqing; Liu Pingsheng; Xu qing; Liu Peng; Qian Qingfang

    1998-01-01

    The serum thyroid hormones (T 3 , T 4 , TSH, FT 3 and FT 4 ) level and the elements K, Ca, Fe, Cu, Zn, Se and Rb in the erythrocyte in 76 cases is measured by radiometric assay in vitro (RIA and IRMA) and nuclear analytical technique (PIXE and INNA). According to thyroid hormones level, the cases are divided into four groups with hyperthyroid, normal, subhyperthyroid and hypothyroid. The difference and correlation of various parameters in four groups are compared by Oneway-ANOVA and Partial Correlation using SPSS/PC statistical package respectively. The results show that the content of Zn for hypothyroid group is significantly higher than hyperthyroid (P = 0.007) and sub-hyperthyroid (P = 0.046) groups, and the content of Zn for normal is lower than hypothyroid group but not significant difference (P = 0.083), the other elements contents are no significant difference among four groups. The highly significant linear correlation between the contents of K, Zn and Cu in the erythrocyte and T 3 , T 4 level ratio and TSH level is observed in hypothyroid and normal groups, the close correlation between the content of Se and serum T 4 and TSH level is also observed in hyperthyroid and sub-hyperthyroid groups. These suggest that trace elements may be important for the synthesis, metabolism and biological function of thyroid hormones

  20. Organometallic chemistry of the f-elements: toward new development: cyanide ligand of f-elements

    International Nuclear Information System (INIS)

    Herve, Alexandre

    2014-01-01

    The cyanide ligand is one of the most widely used ligands in coordination chemistry of d-transition metals. The low number of cyanide complexes of lanthanides and actinides incited us to develop this field for reactivity and theoretical aspects, and also for their potentially interesting physicochemical properties. In this Ph.D., we investigated the reactivity of [An(Cot) 2 ] (An = Th, U ; Cot = C 8 H 8 2- ) and [M f (N*) 3 ] q+ (q = 0, 1; M f = Ce, U ; N* = -N(SiMe 3 ) 2 ) precursors toward the cyanide ion. The first chapter is dedicated to the synthesis and characterization of trivalent f-elements cyanide complexes [M f (N*) 3 (CN)][M], [M f (N*) 3 (CN) 2 ][M] 2 et [M f (N*) 2 (CN) 3 ][M] 2 and the cyanido-bridged binuclear compounds [{M f (N*) 3 } 2 (μ-CN)][M] (M = NR 4 , K(18-C-6)). Crystals of the bis(cyanido) uranium and cerium complexes are not isostructural since the data revealed distinct coordination modes of the CN group, through the C or N atom to the U 3+ or Ce 3+ metal center, respectively. In chapter 2, the novel silyl-amide uranium(IV) precursor [U(N*) 3 ][BPh 4 ] has been isolated, and proved to be useful for the synthesis of the cationic species [{U(N*) 3 } 2 (μ-CN)][BPh 4 ] and the neutral monocyanide [M f (N*) 3 (CN)] and anionic bis(cyanide) [M f (N*) 3 (CN) 2 ][M] derivatives. Here again, the X-ray data reveal the uncommon N coordination mode of the CN group to the U(IV) center. This global differentiation has been analyzed using density functional theory calculations. The observed preferential coordination of the cyanide ion in Ce(III)-NC, U(III)-CN and U(IV)-NC is corroborated by energetic considerations and by the comparison of DFT optimized geometries with the true crystal structures. Finally, the recent discovery of the first bent 'uranocene' species, eg [U(Cot) 2 (CN)] - , led us to compare the reactivity of the actinocenes [An(Cot) 2 ] (Th, U) in order to understand the effect of the metal electron configuration

  1. Exploring and Implementing Participatory Action Synthesis

    Science.gov (United States)

    Wimpenny, Katherine; Savin-Baden, Maggi

    2012-01-01

    This article presents participatory action synthesis as a new approach to qualitative synthesis which may be used to facilitate the promotion and use of qualitative research for policy and practice. The authors begin by outlining different forms of qualitative research synthesis and then present participatory action synthesis, a collaborative…

  2. Survival and compound nucleus probability of super heavy element Z = 117

    Energy Technology Data Exchange (ETDEWEB)

    Manjunatha, H.C. [Government College for Women, Department of Physics, Kolar, Karnataka (India); Sridhar, K.N. [Government First grade College, Department of Physics, Kolar, Karnataka (India)

    2017-05-15

    As a part of a systematic study for predicting the most suitable projectile-target combinations for heavy-ion fusion experiments in the synthesis of {sup 289-297}Ts, we have calculated the transmission probability (T{sub l}), compound nucleus formation probabilities (P{sub CN}) and survival probability (P{sub sur}) of possible projectile-target combinations. We have also studied the fusion cross section, survival cross section and fission cross sections for different projectile-target combination of {sup 289-297}Ts. These theoretical parameters are required before the synthesis of the super heavy element. The calculated probabilities and cross sections show that the production of isotopes of the super heavy element with Z = 117 is strongly dependent on the reaction systems. The most probable reactions to synthetize the super heavy nuclei {sup 289-297}Ts are worked out and listed explicitly. We have also studied the variation of P{sub CN} and P{sub sur} with the mass number of projectile and target nuclei. This work is useful in the synthesis of the super heavy element Z = 117. (orig.)

  3. Survival and compound nucleus probability of super heavy element Z = 117

    International Nuclear Information System (INIS)

    Manjunatha, H.C.; Sridhar, K.N.

    2017-01-01

    As a part of a systematic study for predicting the most suitable projectile-target combinations for heavy-ion fusion experiments in the synthesis of "2"8"9"-"2"9"7Ts, we have calculated the transmission probability (T_l), compound nucleus formation probabilities (P_C_N) and survival probability (P_s_u_r) of possible projectile-target combinations. We have also studied the fusion cross section, survival cross section and fission cross sections for different projectile-target combination of "2"8"9"-"2"9"7Ts. These theoretical parameters are required before the synthesis of the super heavy element. The calculated probabilities and cross sections show that the production of isotopes of the super heavy element with Z = 117 is strongly dependent on the reaction systems. The most probable reactions to synthetize the super heavy nuclei "2"8"9"-"2"9"7Ts are worked out and listed explicitly. We have also studied the variation of P_C_N and P_s_u_r with the mass number of projectile and target nuclei. This work is useful in the synthesis of the super heavy element Z = 117. (orig.)

  4. Automatic welding of fuel elements; Soudure automatique des elements combustibles

    Energy Technology Data Exchange (ETDEWEB)

    Briola, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    The welding process depends on the type of fuel element, the can material and the number of cartridges to be welded: - inert-gas welding (used for G2 and the 1. set of EL3), - inert atmosphere arc welding (used for welding uranium and zirconium), - electronic welding (used for the 2. set of EL3 and the tank of Proserpine). (author) [French] Suivant le type d'element combustible, le materiau de gaine et l'importance de la serie a fabriquer, le soudeur dispose des differents procedes examines dans cette communication: - soudure classique a l'arc sous gaz inerte (utilisee pour G2 et le premier jeu EL3), - soudure en atmosphere complete d'argon (utilisee pour la soudure d'uranium et de zirconium), - soudure electronique (utilisee pourdeuxieme jeu EL3 et la cuve de Proserpine). (auteur)

  5. Coordinate Regulation of Yeast Sterol Regulatory Element-binding Protein (SREBP) and Mga2 Transcription Factors.

    Science.gov (United States)

    Burr, Risa; Stewart, Emerson V; Espenshade, Peter J

    2017-03-31

    The Mga2 and Sre1 transcription factors regulate oxygen-responsive lipid homeostasis in the fission yeast Schizosaccharomyces pombe in a manner analogous to the mammalian sterol regulatory element-binding protein (SREBP)-1 and SREBP-2 transcription factors. Mga2 and SREBP-1 regulate triacylglycerol and glycerophospholipid synthesis, whereas Sre1 and SREBP-2 regulate sterol synthesis. In mammals, a shared activation mechanism allows for coordinate regulation of SREBP-1 and SREBP-2. In contrast, distinct pathways activate fission yeast Mga2 and Sre1. Therefore, it is unclear whether and how these two related pathways are coordinated to maintain lipid balance in fission yeast. Previously, we showed that Sre1 cleavage is defective in the absence of mga2 Here, we report that this defect is due to deficient unsaturated fatty acid synthesis, resulting in aberrant membrane transport. This defect is recapitulated by treatment with the fatty acid synthase inhibitor cerulenin and is rescued by addition of exogenous unsaturated fatty acids. Furthermore, sterol synthesis inhibition blocks Mga2 pathway activation. Together, these data demonstrate that Sre1 and Mga2 are each regulated by the lipid product of the other transcription factor pathway, providing a source of coordination for these two branches of lipid synthesis. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

  6. Molecular structure design and soft template synthesis of aza-, oxaaza- and thiaazamacrocyclic metal chelates in the gelatin matrix

    OpenAIRE

    Oleg V. Mikhailov

    2017-01-01

    The data about of soft template synthesis proceeding in gelatin matrices in [3d-element M(II) ion – (N,S)- or (N,O,S)-ambidentate ligson – mono- or dicarbonyl ligson] systems, have been considered and discussed. The chemical nature of the final products of template synthesis formed under these specific conditions, has been compared with the chemical nature of the final products formed by template synthesis in solutions. It has been noted that in many cases, the nature and chemical composition...

  7. Superheavy-element spectroscopy: Correlations along element 115 decay chains

    Science.gov (United States)

    Rudolph, D.; Forsberg, U.; Sarmiento, L. G.; Golubev, P.; Fahlander, C.

    2016-05-01

    Following a brief summary of the region of the heaviest atomic nuclei yet created in the laboratory, data on more than hundred α-decay chains associated with the production of element 115 are combined to investigate time and energy correlations along the observed decay chains. Several of these are analysed using a new method for statistical assessments of lifetimes in sets of decay chains.

  8. A synthesis theory for self-oscillating adaptive systems /SOAS/

    Science.gov (United States)

    Horowitz, I.; Smay, J.; Shapiro, A.

    1974-01-01

    A quantitative synthesis theory is presented for the Self-Oscillating Adaptive System (SOAS), whose nonlinear element has a static, odd character with hard saturation. The synthesis theory is based upon the quasilinear properties of the SOAS to forced inputs, which permits the extension of quantitative linear feedback theory to the SOAS. A reasonable definition of optimum design is shown to be the minimization of the limit cycle frequency. The great advantages of the SOAS is its zero sensitivity to pure gain changes. However, quasilinearity and control of the limit cycle amplitude at the system output, impose additional constraints which partially or completely cancel this advantage, depending on the numerical values of the design parameters. By means of narrow-band filtering, an additional factor is introduced which permits trade-off between filter complexity and limit cycle frequency minimization.

  9. High rate flame synthesis of highly crystalline iron oxide nanorods

    International Nuclear Information System (INIS)

    Merchan-Merchan, W; Taylor, A M; Saveliev, A V

    2008-01-01

    Single-step flame synthesis of iron oxide nanorods is performed using iron probes inserted into an opposed-flow methane oxy-flame. The high temperature reacting environment of the flame tends to convert elemental iron into a high density layer of iron oxide nanorods. The diameters of the iron oxide nanorods vary from 10 to 100 nm with a typical length of a few microns. The structural characterization performed shows that nanorods possess a highly ordered crystalline structure with parameters corresponding to cubic magnetite (Fe 3 O 4 ) with the [100] direction oriented along the nanorod axis. Structural variations of straight nanorods such as bends, and T-branched and Y-branched shapes are frequently observed within the nanomaterials formed, opening pathways for synthesis of multidimensional, interconnected networks

  10. The origin of the universe and nuclear synthesis

    Directory of Open Access Journals (Sweden)

    J. P. F. Sellschop

    1988-03-01

    Full Text Available The origin of the universe and nuclear synthesis are discussed in this paper. The concept of the “Big Bang” is introduced in cosmology from observational evidence that the universe is expanding. The language of elementary particle physics is used to describe the evolution of the universe starting at a very small fraction of a second after the "Big Bang”. Various “Eras” are identified during which certain nuclear processes predominate. At a later stage the remarkable nuclear synthesis of carbon takes place, leading to the evolution of other elements. Neutrino measurements are important to validate physical theories in this field and some results of such measurements by the WITS-CSIR Schonland Research Centre are presented.

  11. ‘Umpolung’ Reactivity in Semiaqueous Amide and Peptide Synthesis

    Science.gov (United States)

    Shen, Bo; Makley, Dawn M.; Johnston, Jeffrey N.

    2010-01-01

    The amide functional group is one of Nature’s key functional and structural elements, most notably within peptides. Amides are also key intermediates in the preparation of a diverse range of therapeutic small molecules. Its construction using available methods focuses principally upon dehydrative approaches, although oxidative and radical-based methods are representative alternatives. During the carbon-nitrogen bond forming step in most every example, the carbon and nitrogen bear electrophilic and nucleophilic character, respectively. Here we show that activation of amines and nitroalkanes with an electrophilic iodine source in wet THF can lead directly to amide products. Preliminary observations support a mechanistic construct in which reactant polarity is reversed (umpolung) during C-N bond formation relative to traditional approaches. The use of nitroalkanes as acyl anion equivalents provides a conceptually innovative approach to amide and peptide synthesis, and one that might ultimately provide for efficient peptide synthesis that is fully reliant on enantioselective methods. PMID:20577205

  12. Synthesis of 2-phosphaadamantane derivatives

    International Nuclear Information System (INIS)

    Zemlyanoi, V.N.; Aleksandrov, A.M.; Kukhar', V.P.

    1986-01-01

    The authors describe the synthesis and properties of 2-phosphadamantane derivatives. For the synthesis of 2-phosphaadamantane derivatives they decided to use the methodology of the synthesis of 2-thiaadamantane. The IR spectra were determined on CHCl 3 solutions with a Specord 711R spectrometer, the PMR spectra were determined on Tesla BS-467 (60 MHz) and Bruker WP-200 (200 MHz) spectrometers, external standard hexamethyldisiloxane, the 31 P NMR spectra were determined on Tesla BS-487 C (30 MHz) and Bruker WP-200 (81 MHz) spectrometers, external standard 85% phosphoric acid, and the mass spectra were determined on an MS-1302 spectrometer

  13. The Transuranium Elements - Present Status: Nobel Lecture

    Science.gov (United States)

    Seaborg, G. T.

    1951-12-12

    The discovery of the transuranium elements and the work done on them up to the present time are reviewed. The properties of these elements, their relationship to other elements, their place in the periodic table, and the possibility of production and identification of other transuranium elements are discussed briefly.

  14. Reliability-Based Optimization of Structural Elements

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard

    In this paper structural elements from an optimization point of view are considered, i.e. only the geometry of a structural element is optimized. Reliability modelling of the structural element is discussed both from an element point of view and from a system point of view. The optimization...

  15. Electrochemical synthesis and characterization of copper (I oxide

    Directory of Open Access Journals (Sweden)

    Bugarinović Sanja J.

    2009-01-01

    Full Text Available The quest and need for clean and economical energy sources have increased interest in the development of thin film cells technologies. Electrochemical deposition is an attractive method for synthesis of thin films. It offers the advantages of low synthesis temperature, low cost and high purity. Copper (I oxide or cuprous oxide is an oxide semiconductor which is used as the anodic material in the form of thin film in lithium batteries and solar cells. The cathodic process of synthesis of cuprous oxide thin film is carried out in a potentiostatic mode from the organic electrolyte. The process parameters are chosen in that way to accomplish maximum difference between the potentials at which Cu2O and CuO are obtained. The electrochemical characterization was carried out by cyclic voltammetry. The electrodeposition techniques are particularly well suited for the deposition of single elements but it is also possible to carry out simultaneous depositions of several elements and syntheses of well-defined alternating layers of metals and oxides with thicknesses down to a few nm. Nanomaterials exhibit novel physical properties and play an important role in fundamental research. In addition, cuprous oxide is commonly used as a pigment, a fungicide, and an antifouling agent for marine paints. It is insoluble in water and organic solvents. This work presents the examinations of the influence of bath, temperature, pH and current density on the characteristics of electrochemically synthesized cuprous oxide. In the 'classic' process of synthesis, which is carried out under galvanostatic conditions on the anode, the grain size of the powder decreases with the increase in current density while the grain colour becomes lighter. The best commercial quality of the Cu2O (grain size, colour, content of choride was obtained at the temperature of 80°C, concentration of NaCl of 3 mol/dm3 and current density of 400 A/m2.

  16. Synthesis, characterization, thermal

    Directory of Open Access Journals (Sweden)

    Selma Bal

    2017-09-01

    Full Text Available This work explains the synthesis of a new azo-Schiff base compound, derived from condensation between N-ethylcarbazole-3-carbaldehyde and 1,3-diaminopropane, followed by azo coupling reaction with the diazonium salt of 2-amino-4-methyl phenol. The newly synthesized azo-Schiff base was further reacted with the acetate salts of Copper, Cobalt and Nickel to give three coordination compounds. All synthesized compounds have been characterized through spectral analysis. The coordination compounds have been examined for their thermal and catalytic features. Good and moderate yields were obtained for the oxidation of styrene and cyclohexene. Thermal features of the ligand and its complexes have been explained and the results obtained have supported the proposed structures.

  17. Synthesis of ruthenium phosphides

    International Nuclear Information System (INIS)

    Chernogorenko, V.B.; Lynchak, K.A.; Kulik, L.Ya.; Shkaravskij, Yu.F.; Klochkov, L.A.

    1977-01-01

    A method of ampoule synthesis of ruthenium phosphides, Ru 2 P, RuP, and RuP 2 , with stepwise heating of stoichimetric charges in a single-zone furnace is developed. A method for synthesizing ruthenium diphosphide by phosphidization of a ruthenium powder with phosphine at 1150 deg C is worked out. The optimum conditions of its manufacture are found by planning an extremal experiment. Interaction of PH 3 with ruthenium proceeds by the diffusion mechanism and obeys the parabolic law. An extraction-photometric method for determining phosphorus in phosphides is elaborated. Ruthenium phosphides are extremely corrosion-resistant in acids and alkalis. Ru 2 P and RuP exhibit metallic conductivity

  18. Trace element analysis: a diagnostic tool

    International Nuclear Information System (INIS)

    Qureshi, I.H.; Cheema, M.N.

    1976-09-01

    The human mody continuously assimilates a variety of elements from the environment, and the concentration of these elements in the blood is regulated by means of various homeostatic mechanisms. Some of the elements, though present in very small amounts, have highly specialized functions in initiating many biochemical reactions. These elements, known as essential trace elements, are closely related to human diseases since their deficiency or excess induces physiological changes. Many diseases such as hypertension, atherosclerosis, diabetes, etc., are related to an imbalance in trace element. The measurement of trace elements in body fluids and tissues can, therefore, be effectively employed for diagnostic tests

  19. New Fragment Separation Technology for Superheavy Element Research

    International Nuclear Information System (INIS)

    Shaughnessy, D A; Moody, K J; Henderson, R A; Kenneally, J M; Landrum, J H; Lougheed, R W; Patin, J B; Stoyer, M A; Stoyer, N J; Wild, J F; Wilk, P A

    2008-01-01

    This project consisted of three major research areas: (1) development of a solid Pu ceramic target for the MASHA separator, (2) chemical separation of nuclear decay products, and (3) production of new isotopes and elements through nuclear reactions. There have been 16 publications as a result of this project, and this collection of papers summarizes our accomplishments in each of the three areas of research listed above. The MASHA (Mass Analyzer for Super-Heavy Atoms) separator is being constructed at the U400 Cyclotron at the Flerov Laboratory of Nuclear Reactions in Dubna, Russia. The purpose of the separator is to physically separate the products from nuclear reactions based on their isotopic masses rather than their decay characteristics. The separator was designed to have a separation between isotopic masses of ±0.25 amu, which would enable the mass of element 114 isotopes to be measured with outstanding resolution, thereby confirming their discovery. In order to increase the production rate of element 114 nuclides produced via the 244 Pu+ 48 Ca reaction, a new target technology was required. Instead of a traditional thin actinide target, the MASHA separator required a thick, ceramic-based Pu target that was thick enough to increase element 114 production while still being porous enough to allow reaction products to migrate out of the target and travel through the separator to the detector array located at the back end. In collaboration with UNLV, we began work on development of the Pu target for MASHA. Using waste-form synthesis technology, we began by creating zirconia-based matrices that would form a ceramic with plutonium oxide. We used samarium oxide as a surrogate for Pu and created ceramics that had varying amounts of the starting materials in order to establish trends in material density and porosity. The results from this work are described in more detail in Refs. [1,4,10]. Unfortunately, work on MASHA was delayed in Russia because it was found that

  20. De Novo Glutamine Synthesis

    Science.gov (United States)

    He, Qiao; Shi, Xinchong; Zhang, Linqi; Yi, Chang; Zhang, Xuezhen

    2016-01-01

    Purpose: The aim of this study was to investigate the role of de novo glutamine (Gln) synthesis in the proliferation of C6 glioma cells and its detection with 13N-ammonia. Methods: Chronic Gln-deprived C6 glioma (0.06C6) cells were established. The proliferation rates of C6 and 0.06C6 cells were measured under the conditions of Gln deprivation along with or without the addition of ammonia or glutamine synthetase (GS) inhibitor. 13N-ammonia uptake was assessed in C6 cells by gamma counting and in rats with C6 and 0.06C6 xenografts by micro–positron emission tomography (PET) scanning. The expression of GS in C6 cells and xenografts was assessed by Western blotting and immunohistochemistry, respectively. Results: The Gln-deprived C6 cells showed decreased proliferation ability but had a significant increase in GS expression. Furthermore, we found that low concentration of ammonia was sufficient to maintain the proliferation of Gln-deprived C6 cells, and 13N-ammonia uptake in C6 cells showed Gln-dependent decrease, whereas inhibition of GS markedly reduced the proliferation of C6 cells as well as the uptake of 13N-ammoina. Additionally, microPET/computed tomography exhibited that subcutaneous 0.06C6 xenografts had higher 13N-ammonia uptake and GS expression in contrast to C6 xenografts. Conclusion: De novo Gln synthesis through ammonia–glutamate reaction plays an important role in the proliferation of C6 cells. 13N-ammonia can be a potential metabolic PET tracer for Gln-dependent tumors. PMID:27118759

  1. CERCA's fuel elements instrumentation manufacturing

    International Nuclear Information System (INIS)

    Harbonnier, G.; Jarousse, C.; Pin, T.; Febvre, M.; Colomb, P.

    2005-01-01

    When research and test reactors wish to further understand the Fuel Elements behavior when operating as well as mastering their irradiation conditions, operators carry out neutron and thermo hydraulic analysis. For thermal calculation, the codes used have to be preliminary validated, at least in the range of the reactor safety operational limits. When some further investigations are requested either by safety authorities or for its own reactor needs, instrumented tools are the ultimate solution for providing representative measurements. Such measurements can be conducted for validating thermal calculation codes, at nominal operating condition as well as during transients ones, or for providing numerous and useful data in the frame of a new products qualification program. CERCA, with many years of experience for implanting thermocouples in various products design, states in this poster his manufacturing background on instrumented elements, plates or targets. (author)

  2. Automation of finite element methods

    CERN Document Server

    Korelc, Jože

    2016-01-01

    New finite elements are needed as well in research as in industry environments for the development of virtual prediction techniques. The design and implementation of novel finite elements for specific purposes is a tedious and time consuming task, especially for nonlinear formulations. The automation of this process can help to speed up this process considerably since the generation of the final computer code can be accelerated by order of several magnitudes. This book provides the reader with the required knowledge needed to employ modern automatic tools like AceGen within solid mechanics in a successful way. It covers the range from the theoretical background, algorithmic treatments to many different applications. The book is written for advanced students in the engineering field and for researchers in educational and industrial environments.

  3. Transuranic elements and nuclear wastes

    International Nuclear Information System (INIS)

    Bowen, V.T.

    1974-01-01

    The contamination of oceans and marine life by transuranic elements (elements of atomic number greater than 92) is the main concern of this paper. Wastes of three different types, low-level, intermediate-level, and high-level, are considered. Fallout of Pu and other transuranics is discussed as it affects marine biogeochemistry and geochemistry. Different paths of absorption or uptake under various conditions of release are pointed out in some detail. The transfer of radioactivity to mammals from marine sources is considered in some detail. Waste disposal practices at Windscale are reviewed. It is concluded that the problems associated with transuranic wastes in oceans and marine life are very complex. Monitoring of waste release and uptake is concluded to not be enough. Each situation of release of transuranics to the environment should be treated as an experiment and milked for all the information that it can reveal. The tremendous expenditure of money and manpower necessary for such an undertaking is stressed

  4. Representation Elements of Spatial Thinking

    Science.gov (United States)

    Fiantika, F. R.

    2017-04-01

    This paper aims to add a reference in revealing spatial thinking. There several definitions of spatial thinking but it is not easy to defining it. We can start to discuss the concept, its basic a forming representation. Initially, the five sense catch the natural phenomenon and forward it to memory for processing. Abstraction plays a role in processing information into a concept. There are two types of representation, namely internal representation and external representation. The internal representation is also known as mental representation; this representation is in the human mind. The external representation may include images, auditory and kinesthetic which can be used to describe, explain and communicate the structure, operation, the function of the object as well as relationships. There are two main elements, representations properties and object relationships. These elements play a role in forming a representation.

  5. Finite elements methods in mechanics

    CERN Document Server

    Eslami, M Reza

    2014-01-01

    This book covers all basic areas of mechanical engineering, such as fluid mechanics, heat conduction, beams, and elasticity with detailed derivations for the mass, stiffness, and force matrices. It is especially designed to give physical feeling to the reader for finite element approximation by the introduction of finite elements to the elevation of elastic membrane. A detailed treatment of computer methods with numerical examples are provided. In the fluid mechanics chapter, the conventional and vorticity transport formulations for viscous incompressible fluid flow with discussion on the method of solution are presented. The variational and Galerkin formulations of the heat conduction, beams, and elasticity problems are also discussed in detail. Three computer codes are provided to solve the elastic membrane problem. One of them solves the Poisson’s equation. The second computer program handles the two dimensional elasticity problems, and the third one presents the three dimensional transient heat conducti...

  6. Solid Lubricated Rolling Element Bearings

    Science.gov (United States)

    1979-02-15

    lubricant into uneven patches of varnish . This varnish , along with the file-like action of the exposed ball carbides on the relatively softer races, can...its structure. Fluorine , one of the most reactive elements, reacts with graphite without combustion from about 790’F to 1022°F, forming a grey-colored...to allow for molding and machining after molding. 0 Method 2 (Hughes) Impregnating these dense weaves with a Thermid 600 polyimide varnish

  7. Integral nuclear fuel element assembly

    International Nuclear Information System (INIS)

    Schluderberg, D. C.

    1985-01-01

    An integral nuclear fuel element assembly utilizes longitudinally finned fuel pins. The continuous or interrupted fins of the fuel pins are brazed to fins of juxtaposed fuel pins or directly to the juxtaposed fuel pins or both. The integrally brazed fuel assembly is designed to satisfy the thermal and hydraulic requirements of a fuel assembly lattice having moderator to fuel atom ratios required to achieve high conversion and breeding ratios

  8. Grid for a fuel element

    International Nuclear Information System (INIS)

    1975-01-01

    An illustrative embodiment of the invention has one or more corrugations formed in the surface of a fuel element grid for a nuclear reactor. Not only does the corrugation enhance the strength of the grid plate in which it is formed, but it also provides a simple and convenient means for regulating the reactor coolant pressure drop through an appropriate choice of the corrugation depth

  9. Blade-element/momentum theory

    DEFF Research Database (Denmark)

    Sørensen, Jens Nørkær

    2016-01-01

    Although there exists a large variety of methods for predicting performance and loadings of wind turbines, the only approach used today by wind turbine manufacturers is based on the blade-element/momentum (BEM) theory by Glauert (Aerodynamic theory. Springer, Berlin, pp. 169-360, 1935). A basic...... assumption in the BEM theory is that the flow takes place in independent stream tubes and that the loading is determined from two-dimensional sectional airfoil characteristics....

  10. Trace Elements in Cardiovascular Diseases

    Energy Technology Data Exchange (ETDEWEB)

    Masironi, R. [Cardiovascular Diseases Unit, World Health Organization, Geneva (Switzerland)

    1970-07-01

    Cardiovascular diseases are the leading cause of death in industrialized countries. Their incidence increases, apparently, as a, function of technological progress so that in the future they may become a major public health problem in developing countries too. Early diagnosis and prevention are the tools best suited to curb such an alarming trend, but our knowledge of these topics is unsatisfactory, Valuable information would be obtained through a systematic investigation of trace elements in relation to cardiovascular function and to various types of cardiovascular diseases. Such studies would provide clues to the following questions: 1. Why does the incidence and type of cardiovascular disease differ from one country to another? May this be related to differences in tissue mineral concentrations among various population groups? 2. Which trace elements if any are beneficial to cardiovascular health, and which are harmful ones that may act as aetiological agents for some cardiovascular diseases? 3. Is it possible to utilize measurements of mineral element concentration for diagnostic purposes in cardiovascular disease? (author)

  11. Inorganic elements in sugar samples

    Energy Technology Data Exchange (ETDEWEB)

    Salles, Paulo M.B. de; Campos, Tarcisio P.R. de, E-mail: pauladesalles@yahoo.com.br, E-mail: tprcampos@pq.cnpq.br [Universidade Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Nuclear; Menezes, Maria Angela de B.C., E-mail: menezes@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2013-07-01

    Sugar is considered a safe food ingredient; however, it can be contaminated by organic elements since its planting until its production process. Thus, this study aims at checking the presence of inorganic elements in samples of crystal, refined and brown sugar available for consumption in Brazil. The applied technique was neutron activation analysis, the k{sub 0} method, using the TRIGA MARK - IPR-R1 reactor located at CDTN/CNEN, in Belo Horizonte. It was identified the presence of elements such as, Au, Br, Co, Cr, Hf, K, Na, Sb, Sc and Zn in the samples of crystal/refined sugar and the presence of As, Au, Br, Ca, Co, Cr, Cs, Fe, Hf, K, Na, Sb, Sc, Sm, Sr, Th and Zn in the brown sugar samples. The applied technique was appropriate to this study because it was not necessary to put the samples in solution, essential condition in order to apply other techniques, avoiding contaminations and sample losses, besides allowing a multi elementary detection in different sugar samples. (author)

  12. Fast breeder fuel element development

    International Nuclear Information System (INIS)

    Marth, W.; Muehling, G.

    1983-08-01

    This report is a compilation of the papers which have been presented during a seminar ''Fast Breeder Fuel Element Development'' held on November 15/16, 1982 at KfK. The papers give a survey of the status, of the obtained results and of the necessary work, which still has to be done in the frame of various development programmes for fast breeder fuel elements. In detail the following items were covered by the presentations: - the requirements and boundary conditions for the design of fuel pins and elements both for the reference concept of the SNR 300 core and for the large, commercial breeder type of the future (presentation 1,2 and 6); - the fabrication, properties and characterization of various mixed oxide fuel types (presentations 3,4 and 5); - the operational fuel pin behaviour, limits of different design concepts and possible mechanism for fuel pin failures (presentations (7 and 8); - the situation of cladding- and wrapper materials development especially with respect to the high burn-up values of commercial reactors (presentations 9 and 10); - the results of the irradiation experiments performed under steady-state and non-stationary operational conditions and with failed fuel pins (presentations 11, 12, 13 and 14). (orig./RW) [de

  13. Inorganic elements in sugar samples

    International Nuclear Information System (INIS)

    Salles, Paulo M.B. de; Campos, Tarcisio P.R. de

    2013-01-01

    Sugar is considered a safe food ingredient; however, it can be contaminated by organic elements since its planting until its production process. Thus, this study aims at checking the presence of inorganic elements in samples of crystal, refined and brown sugar available for consumption in Brazil. The applied technique was neutron activation analysis, the k 0 method, using the TRIGA MARK - IPR-R1 reactor located at CDTN/CNEN, in Belo Horizonte. It was identified the presence of elements such as, Au, Br, Co, Cr, Hf, K, Na, Sb, Sc and Zn in the samples of crystal/refined sugar and the presence of As, Au, Br, Ca, Co, Cr, Cs, Fe, Hf, K, Na, Sb, Sc, Sm, Sr, Th and Zn in the brown sugar samples. The applied technique was appropriate to this study because it was not necessary to put the samples in solution, essential condition in order to apply other techniques, avoiding contaminations and sample losses, besides allowing a multi elementary detection in different sugar samples. (author)

  14. Root uptake of transuranic elements

    International Nuclear Information System (INIS)

    Schulz, R.K.

    1977-01-01

    The uptake of elements by plant roots is one of the important pathways of entry of many elements into the food chain of man. Data are cited showing plutonium concentration ratios, plant/soil, ranging from 10 -10 to 10 -3 . Concentration ratios for americium range from 10 -7 to 10 +1 . Limited experiments with curium and neptunium indicate that root uptake of curium is similar to that of americium and that plant uptake of neptunium is substantially larger than that of curium and americium. The extreme ranges of concentration ratios cited for plutonium and americium are due to a number of causes. Experimental conditions such as very intensive cropping will lead to abnormally high concentration ratios. In some experiments, addition of chelating agents markedly increased plant root uptake of transuranic elements. Particle size and composition of the source material influenced uptake of the transuranics by plants. Translocation within the plant, and soil factors such as pH and organic matter content, all affect concentration ratios

  15. Elemental composition of cosmic ray

    International Nuclear Information System (INIS)

    Yanagida, Shohei

    1987-01-01

    The report first summarizes some data that have been obtained so far from observation of isotopes and elements in cosmic rays in the low energy region. Then, objectives of studies planned to be carried out with Astromag are outlined and the number of incident particles expected to be measured by baloon observation is estimated. Heavy elements with atomic numbers of greater than 30 are considered to be formed through neutron absorption reactions by the s- or r-process. Observations show that products of the r-process is abundant in cosmic ray sources. The escape length depends on energy. In relation to this, it has been reported that the ratios Ar-Fe and Ca-Fe increase above 200 GeV-n while such a tendency is not observed for K, Sc, Ti or V. Thus, no satisfactory models are available at present which can fully explain the changes in the escape length. The ratio 3 He- 4 He in the range of 5 - 10 GeV-n is inconsistent with the general theory that interprets the escape length of heavy elements. Some models, including the supermetallicity model and Wolf Rayet theory, have been proposed to explain unusual ratios of isotopes in cosmic rays, but more measurements are required to verify them. It is expected that Astromag can serve to make observations that can clarify these points. (Nogami, K.)

  16. Group theoretical classification of chemical elements

    International Nuclear Information System (INIS)

    Byakov, V.M.; Kulakov, V.I.; Rumer, Y.B.; Fet, A.L.

    1977-01-01

    The method of classification of chemical elements, based on group symmetry principles, is compared with element properties. Elements are considered to be states of a single quantum system, the atomic structure being ignored. Elements treated as states of the system, break down into successively diminishing subsystems, big and small multiplets. The theory, being a group classification, does not describe in detail any of element properties, but leads to a unified qualitative description of all of them simultaneously

  17. Vanillin Synthesis from 4-Hydroxybenzaldehyde

    Science.gov (United States)

    Taber, Douglass F.; Patel, Shweta; Hambleton, Travis M.; Winkel, Emma E.

    2007-01-01

    A regioselective, safe and efficient method for the synthesis of vanillin from 4-hydroxybenzaldehyde is being described. The vanillin derived from the process is cheap and can be used as a flavor or in the paper industry.

  18. Synthesis of deuterated 1-phenylpropenols

    International Nuclear Information System (INIS)

    Denhez, J.P.; Girault, G.; Dizabo, P.

    1981-01-01

    The synthesis of deuterated 1-phenylpropenols is reported. The methods involve either Grignard reactions or selective reduction of α, β unsaturated ketones. These ketones are obtained by degradation of ammonium salts of the Mannich bases. (author)

  19. Synthesis in land change science

    DEFF Research Database (Denmark)

    Magliocca, Nicholas R.; Rudel, Thomas K.; Verburg, Peter H.

    2015-01-01

    Global and regional economic and environmental changes are increasingly influencing local land-use, livelihoods, and ecosystems. At the same time, cumulative local land changes are driving global and regional changes in biodiversity and the environment. To understand the causes and consequences...... of these changes, land change science (LCS) draws on a wide array synthetic and meta-study techniques to generate global and regional knowledge from local case studies of land change. Here, we review the characteristics and applications of synthesis methods in LCS and assess the current state of synthetic research...... based on a meta-analysis of synthesis studies from 1995 to 2012. Publication of synthesis research is accelerating, with a clear trend toward increasingly sophisticated and quantitative methods, including meta-analysis. Detailed trends in synthesis objectives, methods, and land change phenomena...

  20. Total synthesis of solanoeclepin A

    Science.gov (United States)

    Tanino, Keiji; Takahashi, Motomasa; Tomata, Yoshihide; Tokura, Hiroshi; Uehara, Taketo; Narabu, Takashi; Miyashita, Masaaki

    2011-06-01

    Cyst nematodes are troublesome parasites that live on, and destroy, a range of important host vegetable plants. Damage caused by the potato cyst nematode has now been reported in over 50 countries. One approach to eliminating the problem is to stimulate early hatching of the nematodes, but key hatching stimuli are not naturally available in sufficient quantities to do so. Here, we report the first chemical synthesis of solanoeclepin A, the key hatch-stimulating substance for potato cyst nematode. The crucial steps in our synthesis are an intramolecular cyclization reaction for construction of the highly strained tricyclo[5.2.1.01,6]decane skeleton (DEF ring system) and an intramolecular Diels-Alder reaction of a furan derivative for the synthesis of the ABC carbon framework. The present synthesis has the potential to contribute to addressing one of the critical food issues of the twenty-first century.