Investigation of elemental and radiological contamination of soils in two shipyards in Chittagong, Bangladesh

International Nuclear Information System (INIS)

Uddin, M. Shuza; Shariff, M. Asad; Hasan, M. Mehedi

2014-01-01

An analysis of metallic elements and natural radioactivity in soils collected from two shipyards and their surroundings in Chittagong, Bangladesh is presented. The elemental concentrations of the metals Cr, Mn, Fe, Ni and Cu were obtained by PIXE analysis with a 3 MV Tandem Accelerator, and the radioactivity of 226 Ra, 232 Th and 40 K was determined using HPGe gamma-ray spectrometry. From the mean specific activities of the three radionuclides in soil samples, the radium equivalent activity, the gamma absorbed dose rate, the annual effective dose rate and the external hazard index were calculated. The study was focused on investigation of soil contamination via shipbreaking activities, if any. The somewhat higher contents of Cr, Mn, Fe, Ni and Cu in soil samples of shipyards, as compared to other locations, seem to be caused by the shipbreaking activities. The specific radioactivities as well as radium equivalent activity in soils of shipyards are also higher and thus possibly an indirect result of shipbreaking activities.

Investigation of elemental and radiological contamination of soils in two shipyards in Chittagong, Bangladesh

Energy Technology Data Exchange (ETDEWEB)

Uddin, M. Shuza; Shariff, M. Asad; Hasan, M. Mehedi [Tandem Accelerator Facility, Dhaka (Bangladesh). Inst. of Nuclear Science and Technology, Atomic Energy Research Establishment; Barua, Bijoy Sonker [Tandem Accelerator Facility, Dhaka (Bangladesh). Inst. of Nuclear Science and Technology, Atomic Energy Research Establishment; Chittagong Univ. of Engineering and Technology, Chittagong (Bangladesh). Dept. of Physics; Rashid, M. Abdur [Chittagong Univ. of Engineering and Technology, Chittagong (Bangladesh). Dept. of Physics; Kamal, Masud [Radioactivity Testing and Monitoring Lab. Bangladesh Atomic Energy Commission, Chittagong (Bangladesh)

2014-10-01

An analysis of metallic elements and natural radioactivity in soils collected from two shipyards and their surroundings in Chittagong, Bangladesh is presented. The elemental concentrations of the metals Cr, Mn, Fe, Ni and Cu were obtained by PIXE analysis with a 3 MV Tandem Accelerator, and the radioactivity of {sup 226}Ra, {sup 232}Th and {sup 40}K was determined using HPGe gamma-ray spectrometry. From the mean specific activities of the three radionuclides in soil samples, the radium equivalent activity, the gamma absorbed dose rate, the annual effective dose rate and the external hazard index were calculated. The study was focused on investigation of soil contamination via shipbreaking activities, if any. The somewhat higher contents of Cr, Mn, Fe, Ni and Cu in soil samples of shipyards, as compared to other locations, seem to be caused by the shipbreaking activities. The specific radioactivities as well as radium equivalent activity in soils of shipyards are also higher and thus possibly an indirect result of shipbreaking activities.

Multiple cis-regulatory elements are involved in the complex regulation of the sieve element-specific MtSEO-F1 promoter from Medicago truncatula.

Science.gov (United States)

Bucsenez, M; Rüping, B; Behrens, S; Twyman, R M; Noll, G A; Prüfer, D

2012-09-01

The sieve element occlusion (SEO) gene family includes several members that are expressed specifically in immature sieve elements (SEs) in the developing phloem of dicotyledonous plants. To determine how this restricted expression profile is achieved, we analysed the SE-specific Medicago truncatula SEO-F1 promoter (PMtSEO-F1) by constructing deletion, substitution and hybrid constructs and testing them in transgenic tobacco plants using green fluorescent protein as a reporter. This revealed four promoter regions, each containing cis-regulatory elements that activate transcription in SEs. One of these segments also contained sufficient information to suppress PMtSEO-F1 transcription in the phloem companion cells (CCs). Subsequent in silico analysis revealed several candidate cis-regulatory elements that PMtSEO-F1 shares with other SEO promoters. These putative sieve element boxes (PSE boxes) are promising candidates for cis-regulatory elements controlling the SE-specific expression of PMtSEO-F1. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

Experimental investigation of system effects in stressed-skin elements

DEFF Research Database (Denmark)

Dela Stang, B.; Isaksson, T.; Hansson, M.

What kind of behaviour can be expected from stressed-skin elements at failure? To answer this question was a primary objective of the experimental investigation presented in this report. Systems of 3 roof units, each made of 5 parallel beams, have been tested for load-carrying capacity and behavi......What kind of behaviour can be expected from stressed-skin elements at failure? To answer this question was a primary objective of the experimental investigation presented in this report. Systems of 3 roof units, each made of 5 parallel beams, have been tested for load-carrying capacity...

Total and species-specific quantitative analyses of trace elements in sediment by isotope dilution inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Inagaki, Kazumi; Takatsu, Akiko; Yarita, Takashi; Okamoto, Kensaku; Chiba, Koichi

2009-01-01

Isotope dilution inductively coupled plasma mass spectrometry (ID-ICP-MS) is one of the reliable methods for total and species-specific quantitative analysis of trace elements. However, several technical problems (e.g. spectral interference caused from sample constituents) should be overcome to obtain reliable analytical results when environmental samples are analyzed by ID-ICP-MS. In our laboratory, various methods based on ID-ICP-MS have been investigated for reliable quantitative analyses of trace elements in environmental samples. In this paper, coprecipitate separation/ID-ICP-MS for the determination of trace elements in sediment, cation exchange disk filtration/ID-ICP-MS for the determination of selenium in sediment, species-specific ID-ICP-MS using 118 Sn/labeled organotin compounds for the determination of butyltins and phenyltins, and the application of the ID-ICP-MS methods to the certification of sediment reference materials are described. (author)

Element-specific and constant parameters used for dose calculations in SR-Site

International Nuclear Information System (INIS)

Norden, Sara; Avila, Rodolfo; De la Cruz, Idalmis; Stenberg, Kristofer; Grolander, Sara

2010-12-01

The report presents Best Estimate (BE) values and Probability Distribution Functions (PDFs) of Concentration Ratios (CR) for different types of terrestrial and aquatic biota and distribution coefficients (K d ) for organic and inorganic deposits, as well as for suspended matter in freshwater and marine ecosystems. The BE values have been used in deterministic simulations for derivation of Landscape Dose Factors (LDF) applied for dose assessments in SR-Site. The PDFs have been used in probabilistic simulations for uncertainty and sensitivity analysis of the LDFs. The derivation of LDFs for SR-Site is described in /Avila et al. 2010/. The CR and K d values have been derived using both site-specific data measured at Laxemar and Forsmark during the site investigation program and literature data. These two data sources have been combined using Bayesian updating methods, which are described in detail in an Appendix, along with the input data used in the statistical analyses and the results obtained. The report also describes a kinetic-allometric model that was applied for deriving values of CR for terrestrial herbivores in cases when site and literature data for an element were missing. In addition, the report presents values for a number of other parameters used in the SR-Site Radionuclide Model for the biosphere: radionuclide decay-ingrowth data, elemental diffusivities, fractions of element content released during decomposition processes, ingestion of food, water and soil by cattle, elements retention fraction on plant surfaces during irrigation. The report also presents parameter values used in calculation of doses to a reference man: dose coefficients for inhalation, ingestion and external exposure, inhalation rates, ingestion rates of food and water

Element-specific and constant parameters used for dose calculations in SR-Site

Energy Technology Data Exchange (ETDEWEB)

Norden, Sara (Svensk Kaernbraenslehantering AB (Sweden)); Avila, Rodolfo; De la Cruz, Idalmis; Stenberg, Kristofer; Grolander, Sara (Facilia AB (Sweden))

2010-12-15

The report presents Best Estimate (BE) values and Probability Distribution Functions (PDFs) of Concentration Ratios (CR) for different types of terrestrial and aquatic biota and distribution coefficients (K{sub d}) for organic and inorganic deposits, as well as for suspended matter in freshwater and marine ecosystems. The BE values have been used in deterministic simulations for derivation of Landscape Dose Factors (LDF) applied for dose assessments in SR-Site. The PDFs have been used in probabilistic simulations for uncertainty and sensitivity analysis of the LDFs. The derivation of LDFs for SR-Site is described in /Avila et al. 2010/. The CR and K{sub d} values have been derived using both site-specific data measured at Laxemar and Forsmark during the site investigation program and literature data. These two data sources have been combined using Bayesian updating methods, which are described in detail in an Appendix, along with the input data used in the statistical analyses and the results obtained. The report also describes a kinetic-allometric model that was applied for deriving values of CR for terrestrial herbivores in cases when site and literature data for an element were missing. In addition, the report presents values for a number of other parameters used in the SR-Site Radionuclide Model for the biosphere: radionuclide decay-ingrowth data, elemental diffusivities, fractions of element content released during decomposition processes, ingestion of food, water and soil by cattle, elements retention fraction on plant surfaces during irrigation. The report also presents parameter values used in calculation of doses to a reference man: dose coefficients for inhalation, ingestion and external exposure, inhalation rates, ingestion rates of food and water

Characterization of a cis-acting element involved in cell-specific expression of the zebrafish brain aromatase gene.

Science.gov (United States)

Le Page, Yann; Menuet, Arnaud; Kah, Olivier; Pakdel, Farzad

2008-10-01

The cytochrome P450 Aromatase is the key enzyme catalyzing the conversion of androgens into estrogens. In zebrafish, the brain aromatase is encoded by cyp19b. Expression of cyp19b is restricted to radial glial cells bordering forebrain ventricles and is strongly stimulated by estrogens during development. At the promoter level, we have previously shown that an estrogen responsive element (ERE) is required for induction by estrogens. Here, we investigated the role of ERE flanking regions in the control of cell-specific expression. First, we show that a 20 bp length motif, named G x RE (glial x responsive element), acts in synergy with the ERE to mediate the estrogenic induction specifically in glial cells. Second, we demonstrate that, in vitro, this sequence binds factors exclusively present in glial or neuro-glial cells and is able to confer a glial specificity to an artificial estrogen-dependent gene. Taken together, these results contribute to the understanding of the molecular mechanisms allowing cyp19b regulation by estrogens and allowed to identify a promoter sequence involved in the strong estrogen inducibility of cyp19b which is specific for glial cells. The exceptional aromatase activity measured in the brain of teleost fish could rely on such mechanisms.

Investigation of parts and elements of technical reports in nuclear field in Japan

International Nuclear Information System (INIS)

Naramoto, Miyoko; Narui, Shigeko

1985-01-01

Presentation of parts and elements necessary for editing and publishing reports in accordance with SIST-09-1984 (Presentation of Scientific and Technical Reports) was investigated for 65 codes of technical reports in the nuclear field in Japan. English presentation of important elements was also investigated additionally. The investigation shows high presentation fractions (80 -- 100 %) for main bibliographic elements, and medium (66 %) and extremely low (3 %) for abntract and key word, respectively. (The bibliographic elements are described in various parts such as front cover, title page and front matter) and (the subject elements appear mainly in front matter). The title, author's name in Roman character, affiliation, publisher and abstract are described in English with fractions of 80 %, 66 %, 68 % and 62 %, respectively. It is hoped for more publishers and editors of technical reports to accept the standard SIST-09 for efficient processing of secondary information. (author)

Functional dissection of the promoter of the pollen-specific gene NTP303 reveals a novel pollen-specific, and conserved cis-regulatory element.

Science.gov (United States)

Weterings, K; Schrauwen, J; Wullems, G; Twell, D

1995-07-01

Regulatory elements within the promoter of the pollen-specific NTP303 gene from tobacco were analysed by transient and stable expression analyses. Analysis of precisely targeted mutations showed that the NTP303 promoter is not regulated by any of the previously described pollen-specific cis-regulatory elements. However, two adjacent regions from -103 to -86 bp and from -86 to -59 bp were shown to contain sequences which positively regulated the NTP303 promoter. Both of these regions were capable of driving pollen-specific expression from a heterologous promoter, independent of orientation and in an additive manner. The boundaries of the minimal, functional NTP303 promoter were determined to lie within the region -86 to -51 bp. The sequence AAATGA localized from -94 to -89 bp was identified as a novel cis-acting element, of which the TGA triplet was shown to comprise an active part. This element was shown to be completely conserved in the similarly regulated promoter of the Bp 10 gene from Brassica napus encoding a homologue of the NTP303 gene.

Investigation of Elemental Concentrations of Some Medicinal Herbs Collected from Kachin State

International Nuclear Information System (INIS)

Tint Lwin; Soe Myint; Tun Khin

2006-06-01

Five medicinal herbs, which are traditionally used in the Kachin State for the treatment of tuberculosis, different types of cancers, malaria and indigestion problem, were analyzed by the EDXRF techinque to determine the relative concentrations of elements contained in them. The major elements and the trace elements were thoroughly investigated for a comparison purpose

Investigation of selected trace elements in hair samples of eczema patients

International Nuclear Information System (INIS)

Osman, N. O.

2010-12-01

The aim of this case-control study was to investigate the relationship between selected trace elements and skin diseases, namely eczema. Fifty five patients affected by the most frequent eczema types were recruited at the onset of disease at the hospital of dermatology in Khartoum together with thirty healthy controls. Fe, Zn, Cu, and Ni were measured in hair samples obtained from both patients and control group using Atomic Absorption Spectrometry (AAS). Data analysis was performed using the T-test. Partial correlation was used to study the relationship between the elemental concentration. Certified reference material (IAEA-85) Hair Powder) produced by the International Atomic Energy Agency (IAEA) was used as a quality control to check the accuracy and precision of the analytical technique, good agreement was achieved for all elements under investigation. Significant variations (p<0.05) in the concentrations of Fe, Zn, Cu, and Ni in the hair of the patients compared to the control group, and this difference was a decrease of iron, zinc and copper, therefore, should be given to the patient doses of these elements, while there was an increase in the nickel. So it is not included in the treatment. These interesting associations between the levels the of trace elements could be used as an indication for the disease as well as to monitor the treatment. Comparisons of the results obtained in the present study with those conducted for other population in the literature showed very close agreement. The levels of the elements under investigation are comparable with the data obtained from the literature for other populations with exception of Fe which was found to be very high in Sudanese population. (Author)

Investigation of selected trace elements in hair samples of eczema patients

Energy Technology Data Exchange (ETDEWEB)

Osman, N O [Atomic Energy Council, Sudan Academy of Sciences (SAS), Khartoum (Sudan)

2010-12-15

The aim of this case-control study was to investigate the relationship between selected trace elements and skin diseases, namely eczema. Fifty five patients affected by the most frequent eczema types were recruited at the onset of disease at the hospital of dermatology in Khartoum together with thirty healthy controls. Fe, Zn, Cu, and Ni were measured in hair samples obtained from both patients and control group using Atomic Absorption Spectrometry (AAS). Data analysis was performed using the T-test. Partial correlation was used to study the relationship between the elemental concentration. Certified reference material (IAEA-85) Hair Powder) produced by the International Atomic Energy Agency (IAEA) was used as a quality control to check the accuracy and precision of the analytical technique, good agreement was achieved for all elements under investigation. Significant variations (p<0.05) in the concentrations of Fe, Zn, Cu, and Ni in the hair of the patients compared to the control group, and this difference was a decrease of iron, zinc and copper, therefore, should be given to the patient doses of these elements, while there was an increase in the nickel. So it is not included in the treatment. These interesting associations between the levels the of trace elements could be used as an indication for the disease as well as to monitor the treatment. Comparisons of the results obtained in the present study with those conducted for other population in the literature showed very close agreement. The levels of the elements under investigation are comparable with the data obtained from the literature for other populations with exception of Fe which was found to be very high in Sudanese population. (Author)

Investigating Effects of Screen Layout Elements on Interface and Screen Design Aesthetics

OpenAIRE

Altaboli, Ahamed; Lin, Yingzi

2011-01-01

A recent study suggested the use of the screen layout elements of balance, unity, and sequence as a part of a computational model of interface aesthetics. It is argued that these three elements are the most contributed terms in the model. In the current study, a controlled experiment was designed and conducted to systematically investigate effects of these three elements (balance, unity, and sequence) on the perceived interface aesthetics. Results showed that the three elements have signific...

Interaction of a nodule specific, trans-acting factor with distinct DNA elements in the soybean leghaemoglobin Ibc(3) 5' upstream region

DEFF Research Database (Denmark)

Jensen, Erik Østergaard; Marcker, Kjeld A; Schell, J

1988-01-01

Nuclear extracts from soybean nodules, leaves and roots were used to investigate protein-DNA interactions in the 5' upstream (promoter) region of the soybean leghaemoglobin lbc(3) gene. Two distinct regions were identified which strongly bind a nodule specific factor. A Bal31 deletion analysis......, but with different affinities. Elements 1 and 2 share a common motif, although their AT-rich DNA sequences differ. Element 2 is highly conserved at an analogous position in other soybean lb gene 5' upstream regions. Udgivelsesdato: 1988-May...

Investigation of the crack in a reflector element of JRR-4

International Nuclear Information System (INIS)

2008-09-01

The JRR-4 (Japan Research Reactor No.4) has been used as a shared utilization facility for many researches since the first criticality in January 1965. A crack was ascertained on a weld area of one reflector element on December 28, 2007. The Department of Research Reactor and Tandem Accelerator set up an ad hoc working group of experts in the JAEA (Japan Atomic Energy Agency), and investigated cause of crack on the weld area. The following examinations were carried out; visual examination, dimensional examination, fractography examination and so on. It was concluded that the main cause of the crack is the swelling of graphite in the reflector element. The swelling must be due to neutron irradiation. We carried out a radiografical examination of the other reflector elements. As the result, we determined that many of them were not in a suitable state to be used because of swelling of graphite. The design of the new reflector elements should be carried out, based on the relation between the irradiation does and swelling rate, which has been obtained in these investigation. (author)

Investigation of chemical forms of elements in surface waters

International Nuclear Information System (INIS)

Varshal, G.M.; Velyukhanova, T.K.; Koshcheeva, I.Ya.; Dorofeeva, V.A.; Buachidze, N.S.; Kasimova, O.G.; Makharadze, G.A.

1983-01-01

The main trends in the research of the state of elements in natural waters are examined. The hydrolysis of CU(2), Hg(2), Au(3), Sb(3), Ru(4) over a pH range, specific for natural waters, has been studied by solubility and paper electrophoresis technnques and by filtration through cellulose ionites. The regions of predominating different forms of hydroxo complexes have been found and the thermodynamic constants of hydrolysis equilibria have been calculated. Solubility, filtration through sephadexes and cellulose ionites, paper electrophoresis techniques were used to study the complexation of Cu(2), Hg(2), Au(3), Sb(3), Ru(4) with fulvic acids. Some data have been obtained on the composition, stability and molecular-mass distribution of fulvate complexes of ten elements in different oxidation states. High-molecular anionic fulvate complexes are among main forms of most easily hydrolysed elments in solution. The possibility has been shown of prediction of the ratio of coexisting forms of trace elements in solution by theoretical calculations and experimentally Using fractionation on cellulose ionites and sephadexes

''In situ'' investigations of the radioactive fissionable element infiltration and retention in different soils

International Nuclear Information System (INIS)

Oncescu, M.; Danis, A.; Sahagia, M.; Negrescu, C.; Bobe, M.; Balanescu, P.; Burcescu, M.; Tautu, N.

1980-01-01

''In situ'' investigations of the natural and forced infiltration and retention of the fissionable elements from a liquid residue in several natural compacted soils and compacted clays are presented. The velocities and flow rates for different stages of the residue infiltration are determined. The retention of the fissionable elements by variation of the fissionable element concentration with the distance from the place of the residue depot is investigated. (author)

Cell Type-Specific Chromatin Signatures Underline Regulatory DNA Elements in Human Induced Pluripotent Stem Cells and Somatic Cells.

Science.gov (United States)

Zhao, Ming-Tao; Shao, Ning-Yi; Hu, Shijun; Ma, Ning; Srinivasan, Rajini; Jahanbani, Fereshteh; Lee, Jaecheol; Zhang, Sophia L; Snyder, Michael P; Wu, Joseph C

2017-11-10

Regulatory DNA elements in the human genome play important roles in determining the transcriptional abundance and spatiotemporal gene expression during embryonic heart development and somatic cell reprogramming. It is not well known how chromatin marks in regulatory DNA elements are modulated to establish cell type-specific gene expression in the human heart. We aimed to decipher the cell type-specific epigenetic signatures in regulatory DNA elements and how they modulate heart-specific gene expression. We profiled genome-wide transcriptional activity and a variety of epigenetic marks in the regulatory DNA elements using massive RNA-seq (n=12) and ChIP-seq (chromatin immunoprecipitation combined with high-throughput sequencing; n=84) in human endothelial cells (CD31 + CD144 + ), cardiac progenitor cells (Sca-1 + ), fibroblasts (DDR2 + ), and their respective induced pluripotent stem cells. We uncovered 2 classes of regulatory DNA elements: class I was identified with ubiquitous enhancer (H3K4me1) and promoter (H3K4me3) marks in all cell types, whereas class II was enriched with H3K4me1 and H3K4me3 in a cell type-specific manner. Both class I and class II regulatory elements exhibited stimulatory roles in nearby gene expression in a given cell type. However, class I promoters displayed more dominant regulatory effects on transcriptional abundance regardless of distal enhancers. Transcription factor network analysis indicated that human induced pluripotent stem cells and somatic cells from the heart selected their preferential regulatory elements to maintain cell type-specific gene expression. In addition, we validated the function of these enhancer elements in transgenic mouse embryos and human cells and identified a few enhancers that could possibly regulate the cardiac-specific gene expression. Given that a large number of genetic variants associated with human diseases are located in regulatory DNA elements, our study provides valuable resources for deciphering

Investigation of metallic elements in remainders of firings

International Nuclear Information System (INIS)

Kochmann, Sonnia; Riquelme, Ildefonso; Fernandez, Myriam; Vera Planas, Nestor; Insauralde, Arieal; Sanabria, Felipe

1999-07-01

The nuclear analysis its nondestructive characteristics of high sensibility, rapidity and specificity, offers optimal conditions for its application in forensic field, the determination of present metallic elements in the remainders of firings of, firearms like obtention of patterns that help systematic to distinguish originating remainders of other sources, like pyrotechnique devices or contamination of the labor environment, and but important, from the legal point of view, it contributes the certainty and it leaves the possibility of an expertise in a punishable fact taken to the court [es

Experimental investigation of flow-induced control-element movements by noise analysis

International Nuclear Information System (INIS)

Grunwald, G.; Liewers, P.; Schumann, P.; Weiss, F.P.

1978-01-01

The possibility has been reported of separating a single noise component due to flow-induced vibrations of a certain control element from a complex neutron signal which also contained contributions of many other control elements vibrating similarly. One of the basic assumptions for the different methods applied was that the body sound signal originating from touch events with the channel wall is closely correlated with the control-element movement. Some discrepancies between the results of the different methods showed that this assumption may not be entirely fulfilled. This paper investigates this correlation more accurately by measurements of an air flow model of the control-element channel. The pendulum movement of the element, and the body-sound signal due to the touch events with the channel wall, were measured at different flow-rates. The result is that the correlation is not an ideal one. For a constant flow-rate the touch events happen mainly within a small angle region, which means that the touch event marks a certain phase of the movement period and is therefore correlated with the movement. The dispersion of the touch events' angle distribution explains the small discrepancy between the so-called modified averaging method, which uses the sound signal to trigger the averaging procedure, and the partial spectral density method. But not all discrepancies can be explained by these results; they await further investigation. (author)

Specific accumulation of 20 trace elements in great cormorants (Phalacrocorax carbo) from Japan

International Nuclear Information System (INIS)

Nam, Dong-Ha; Anan, Yasumi; Ikemoto, Tokutaka; Okabe, Yuko; Kim, Eun-Young; Subramanian, Annamalai; Saeki, Kazutoshi; Tanabe, Shinsuke

2005-01-01

This study is to elucidate the specific accumulation of 20 trace elements in tissues/organs of great cormorants from two different colonies (Lake Biwa and Mie) in Japan. In the body distribution of trace elements, some elements revealed tissue-specific accumulation such as most of the burden of Mo, Ag and Cd in liver, Tl and Cd in kidney, Cu, Rb and Cs in muscle, and V, Sr and Ba in bone. Gender-related variation was not observed in both populations for most of the trace elements, except for higher hepatic Sr in males from Lake Biwa. Hepatic V, muscular Hg and Tl, and Cd in liver, kidney and muscle increased with growth. Comparison of trace element levels in tissues between the two colonies showed that Cr, Rb, Sr, Cd, Cs, Ba and Tl levels were higher in Lake Biwa than in Mie, whereas Zn, Co and Hg in Mie samples were greater than Lake Biwa. Variations of elemental levels in stomach contents also showed similar patterns, thus, showing that dietary sources tended to be the main factor for these regional variations. Toxic Hg and Cd concentrations in the liver of cormorants from the two colonies were lower than those from other areas, implying relatively low exposure to these metals in the present study sites. Concentrations of V, Co, Ag, Cd, Cs, Hg, Tl, Pb and Bi in liver remained more or less at the same level between 1993 and 2003, while hepatic Cr, Mn, Cu, Zn, Se, Rb, Sr and Ba showed apparent decrease, which might be related to the biological factors. - Dietary sources seemed to be the main reason for variable results

Investigation of trace elements in coal

International Nuclear Information System (INIS)

Gluskoter, H.J.; Cahil, R.A.; Miller, W.G.; Ruch, R.R.; Shimp, N.F.

1976-01-01

A variety of coal samples is currently being extensively analyzed for constituents, including many trace elements, at the Illinois State Geological Survey. The samples include whole coals, washed coals, and bench samples. Among the many determinations made on each sample are analyses for approximately 60 elements, almost twice the number of elements previously determined. The increase is in part the result of the addition of instrumental neutron activation analysis (INAA) equipment to the laboratory. Twenty-five samples of Herrin (No. 6) Coal that had been analyzed previously were subjected to INAA analysis and were found to include Ba, Ce, Cs, Dy, Eu, Au, Hf, I, In, La, Lu, Rb, Sm, Sc, Ag, Sr, Ta, Tb, Th, W, U, and Yb, none of which were reported by previous techniques. These elements generally are present in very small amounts and, with the exception of barium, exhibit no wide range in concentration. The rare earth elements are among those having the narrowest ranges. Wide variations in element content have been observed in bench sets of coals (samples of vertical segments of the coal seam). Many elements, notably germanium, are concentrated at the top and/or bottom of the seam, the high concentrations of Ge being found there in all four bench sets analyzed to date

Improving cluster-based methods for investigating potential for insect pest species establishment: region-specific risk factors

Directory of Open Access Journals (Sweden)

Michael J. Watts

2011-09-01

Full Text Available Existing cluster-based methods for investigating insect species assemblages or profiles of a region to indicate the risk of new insect pest invasion have a major limitation in that they assign the same species risk factors to each region in a cluster. Clearly regions assigned to the same cluster have different degrees of similarity with respect to their species profile or assemblage. This study addresses this concern by applying weighting factors to the cluster elements used to calculate regional risk factors, thereby producing region-specific risk factors. Using a database of the global distribution of crop insect pest species, we found that we were able to produce highly differentiated region-specific risk factors for insect pests. We did this by weighting cluster elements by their Euclidean distance from the target region. Using this approach meant that risk weightings were derived that were more realistic, as they were specific to the pest profile or species assemblage of each region. This weighting method provides an improved tool for estimating the potential invasion risk posed by exotic species given that they have an opportunity to establish in a target region.

In Vitro Selection of a Single-Stranded DNA Molecular Recognition Element Specific for Bromacil

Directory of Open Access Journals (Sweden)

Ryan M. Williams

2014-01-01

Full Text Available Bromacil is a widely used herbicide that is known to contaminate environmental systems. Due to the hazards it presents and inefficient detection methods, it is necessary to create a rapid and efficient sensing device. Towards this end, we have utilized a stringent in vitro selection method to identify single-stranded DNA molecular recognition elements (MRE specific for bromacil. We have identified one MRE with high affinity (Kd=9.6 nM and specificity for bromacil compared to negative targets of selection and other pesticides. The selected ssDNA MRE will be useful as the sensing element in a field-deployable bromacil detection device.

ABO alleles are linked with haplotypes of an erythroid cell-specific regulatory element in intron 1 with a few exceptions attributable to genetic recombination.

Science.gov (United States)

Nakajima, T; Sano, R; Takahashi, Y; Watanabe, K; Kubo, R; Kobayashi, M; Takahashi, K; Takeshita, H; Kominato, Y

2016-01-01

Recent investigation of transcriptional regulation of the ABO genes has identified a candidate erythroid cell-specific regulatory element, named the +5·8-kb site, in the first intron of ABO. Six haplotypes of the site have been reported previously. The present genetic population study demonstrated that each haplotype was mostly linked with specific ABO alleles with a few exceptions, possibly as a result of hybrid formation between common ABO alleles. Thus, investigation of these haplotypes could provide a clue to further elucidation of ABO alleles. © 2015 International Society of Blood Transfusion.

Tissue-Specific Enrichment of Lymphoma Risk Loci in Regulatory Elements.

Science.gov (United States)

Hayes, James E; Trynka, Gosia; Vijai, Joseph; Offit, Kenneth; Raychaudhuri, Soumya; Klein, Robert J

2015-01-01

Though numerous polymorphisms have been associated with risk of developing lymphoma, how these variants function to promote tumorigenesis is poorly understood. Here, we report that lymphoma risk SNPs, especially in the non-Hodgkin's lymphoma subtype chronic lymphocytic leukemia, are significantly enriched for co-localization with epigenetic marks of active gene regulation. These enrichments were seen in a lymphoid-specific manner for numerous ENCODE datasets, including DNase-hypersensitivity as well as multiple segmentation-defined enhancer regions. Furthermore, we identify putatively functional SNPs that are both in regulatory elements in lymphocytes and are associated with gene expression changes in blood. We developed an algorithm, UES, that uses a Monte Carlo simulation approach to calculate the enrichment of previously identified risk SNPs in various functional elements. This multiscale approach integrating multiple datasets helps disentangle the underlying biology of lymphoma, and more broadly, is generally applicable to GWAS results from other diseases as well.

Investigation of elemental changes in brain tissues following excitotoxic injury

International Nuclear Information System (INIS)

Siegele, Rainer; Howell, Nicholas R.; Callaghan, Paul D.; Pastuovic, Zeljko

2013-01-01

Recently the ANSTO heavy ion microprobe has been used for elemental mapping of thin brain tissue sections. The fact that a very small portion of the proton energy is used for X-ray excitation combined with small variations of the major element concentrations makes μ-PIXE imaging and GeoPIXE analysis a challenging task. Excitotoxic brain injury underlies the pathology of stroke and various neurodegenerative disorders. Large fluxes in Ca +2 cytosolic concentrations are a key feature of the initiation of this pathophysiological process. In order to understand if these modifications are associated with changes in the elemental composition, several brain sections have been mapped with μ-PIXE. Increases in Ca +2 cytosolic concentrations were indicative of the pathophysiological process continuing 1 week after an initiating neural insult. We were able to measure significant variations in K and Ca concentration distribution across investigated brain tissue. These variations correlate very well with physiological changes visible in the brain tissue. Moreover, the obtained μ-PIXE results clearly demonstrate that the elemental composition changes significantly correlate with brain drauma

Investigation of elemental changes in brain tissues following excitotoxic injury

Energy Technology Data Exchange (ETDEWEB)

Siegele, Rainer, E-mail: rns@ansto.gov.au [Institute for Environmental Research, ANSTO, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Howell, Nicholas R.; Callaghan, Paul D. [Life Sciences, ANSTO, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); Pastuovic, Zeljko [Institute for Environmental Research, ANSTO, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia)

2013-07-01

Recently the ANSTO heavy ion microprobe has been used for elemental mapping of thin brain tissue sections. The fact that a very small portion of the proton energy is used for X-ray excitation combined with small variations of the major element concentrations makes μ-PIXE imaging and GeoPIXE analysis a challenging task. Excitotoxic brain injury underlies the pathology of stroke and various neurodegenerative disorders. Large fluxes in Ca{sup +2} cytosolic concentrations are a key feature of the initiation of this pathophysiological process. In order to understand if these modifications are associated with changes in the elemental composition, several brain sections have been mapped with μ-PIXE. Increases in Ca{sup +2} cytosolic concentrations were indicative of the pathophysiological process continuing 1 week after an initiating neural insult. We were able to measure significant variations in K and Ca concentration distribution across investigated brain tissue. These variations correlate very well with physiological changes visible in the brain tissue. Moreover, the obtained μ-PIXE results clearly demonstrate that the elemental composition changes significantly correlate with brain drauma.

Investigation of Shear Stud Performance in Flat Plate Using Finite Element Analysis

Directory of Open Access Journals (Sweden)

T.S. Viswanathan

2014-09-01

Full Text Available Three types of shear stud arrangement, respectively featuring an orthogonal, a radial and a critical perimeter pattern, were evaluated numerically. A numerical investigation was conducted using the finite element software ABAQUS to evaluate their ability to resist punching shear in a flat plate. The finite element analysis here is an application of the nonlinear analysis of reinforced concrete structures using three-dimensional solid finite elements. The nonlinear characteristics of concrete were achieved by employing the concrete damaged plasticity model in the finite element program. Transverse shear stress was evaluated using finite element analysis in terms of shear stress distribution for flat plate with and without shear stud reinforcement. The model predicted that shear studs placed along the critical perimeter are more effective compared to orthogonal and radial patterns.

Investigations on Actuator Dynamics through Theoretical and Finite Element Approach

Directory of Open Access Journals (Sweden)

Somashekhar S. Hiremath

2010-01-01

Full Text Available This paper gives a new approach for modeling the fluid-structure interaction of servovalve component-actuator. The analyzed valve is a precision flow control valve-jet pipe electrohydraulic servovalve. The positioning of an actuator depends upon the flow rate from control ports, in turn depends on the spool position. Theoretical investigation is made for No-load condition and Load condition for an actuator. These are used in finite element modeling of an actuator. The fluid-structure-interaction (FSI is established between the piston and the fluid cavities at the piston end. The fluid cavities were modeled with special purpose hydrostatic fluid elements while the piston is modeled with brick elements. The finite element method is used to simulate the variation of cavity pressure, cavity volume, mass flow rate, and the actuator velocity. The finite element analysis is extended to study the system's linearized response to harmonic excitation using direct solution steady-state dynamics. It was observed from the analysis that the natural frequency of the actuator depends upon the position of the piston in the cylinder. This is a close match with theoretical and simulation results. The effect of bulk modulus is also presented in the paper.

Investigation of spatial and historical variations of air pollution around an industrial region using trace and macro elements in tree components

Energy Technology Data Exchange (ETDEWEB)

Odabasi, Mustafa, E-mail: mustafa.odabasi@deu.edu.tr [Department of Environmental Engineering, Faculty of Engineering, Dokuz Eylul University, Tinaztepe Campus, 35160 Buca, Izmir (Turkey); Tolunay, Doganay [Department of Forestry Engineering, Faculty of Forestry, Istanbul University, 34470 Sariyer, Istanbul (Turkey); Kara, Melik; Ozgunerge Falay, Ezgi; Tuna, Gizem; Altiok, Hasan; Dumanoglu, Yetkin; Bayram, Abdurrahman; Elbir, Tolga [Department of Environmental Engineering, Faculty of Engineering, Dokuz Eylul University, Tinaztepe Campus, 35160 Buca, Izmir (Turkey)

2016-04-15

Several trace and macro elements (n = 48) were measured in pine needle, branch, bark, tree ring, litter, and soil samples collected at 27 sites (21 industrial, 6 background) to investigate their spatial and historical variation in Aliaga industrial region in Turkey. Concentrations generally decreased with distance from the sources and the lowest ones were measured at background sites far from major sources. Spatial distribution of anthropogenic trace elements indicated that their major sources in the region are the iron-steel plants, ship-breaking activities and the petroleum refinery. Patterns of 40 elements that were detected in most of the samples were also evaluated to assess their suitability for investigation of historical variations. Observed increasing trends of several trace and macro elements (As, Cr, Fe, Mo, Ni, V, Cu, Pb, Sb, Sn, and Hg) in the tree-ring samples were representative for the variations in anthropogenic emissions and resulting atmospheric concentrations in Aliaga region. It was shown that lanthanides (La, Ce, Pr, Nd, Sm, Gd, Dy, Er, Yb) could also be used for the investigation of historical variations due to specific industrial emissions (i.e., petroleum refining). Results of the present study showed that tree components, litter, and soil could be used to determine the spatial variations of atmospheric pollution in a region while tree rings could be used to assess the historical variations. - Highlights: • Iron-steel plants and refinery are the major trace element emitters in Aliaga region. • Tree components, litter and soil reflected the spatial variations of trace elements. • Elements in tree rings represented the historical variations in air pollution.

Experimental investigation of the flow near the ram element in the brush turbine

Directory of Open Access Journals (Sweden)

Schmirler M.

2015-01-01

Full Text Available The paper focuses on the investigating of the parameters of the fluid flow around the brush turbine ram element. The flow field was evaluated qualitatively by observing changes in density using a Schlieren method. It was also evaluated the influence of the element geometry on the total aerodynamic force of the element. The aerodynamic force was measured directly using a special aerodynamic balance. The aim of the project was to find the simplest element geometry with a maximum force effect and achieve an increase in overall efficiency and reduce the manufacturing costs.

Identification and characterization of cell-specific enhancer elements for the mouse ETF/Tead2 gene.

Science.gov (United States)

Tanoue, Y; Yasunami, M; Suzuki, K; Ohkubo, H

2001-12-21

We have identified and characterized by transient transfection assays the cell-specific 117-bp enhancer sequence in the first intron of the mouse ETF (Embryonic TEA domain-containing factor)/Tead2 gene required for transcriptional activation in ETF/Tead2 gene-expressing cells, such as P19 cells. The 117-bp enhancer contains one GC-rich sequence (5'-GGGGCGGGG-3'), termed the GC box, and two tandemly repeated GA-rich sequences (5'-GGGGGAGGGG-3'), termed the proximal and distal GA elements. Further analyses, including transfection studies and electrophoretic mobility shift assays using a series of deletion and mutation constructs, indicated that Sp1, a putative activator, may be required to predominate over its competition with another unknown putative repressor, termed the GA element-binding factor, for binding to both the GC box, which overlapped with the proximal GA element, and the distal GA element in the 117-bp sequence in order to achieve a full enhancer activity. We also discuss a possible mechanism underlying the cell-specific enhancer activity of the 117-bp sequence.

Capturing structured, pulmonary disease-specific data elements in electronic health records.

Science.gov (United States)

Gronkiewicz, Cynthia; Diamond, Edward J; French, Kim D; Christodouleas, John; Gabriel, Peter E

2015-04-01

Electronic health records (EHRs) have the potential to improve health-care quality by allowing providers to make better decisions at the point of care based on electronically aggregated data and by facilitating clinical research. These goals are easier to achieve when key, disease-specific clinical information is documented as structured data elements (SDEs) that computers can understand and process, rather than as free-text/natural-language narrative. This article reviews the benefits of capturing disease-specific SDEs. It highlights several design and implementation considerations, including the impact on efficiency and expressivity of clinical documentation and the importance of adhering to data standards when available. Pulmonary disease-specific examples of collection instruments are provided from two commonly used commercial EHRs. Future developments that can leverage SDEs to improve clinical quality and research are discussed.

Investigating Effects of Screen Layout Elements on Interface and Screen Design Aesthetics

Directory of Open Access Journals (Sweden)

Ahamed Altaboli

2011-01-01

Full Text Available A recent study suggested the use of the screen layout elements of balance, unity, and sequence as a part of a computational model of interface aesthetics. It is argued that these three elements are the most contributed terms in the model. In the current study, a controlled experiment was designed and conducted to systematically investigate effects of these three elements (balance, unity, and sequence on the perceived interface aesthetics. Results showed that the three elements have significant effects on the perceived interface aesthetics. Significant interactions were also found among the three elements. A regression model relating the perceived visual aesthetics to the three elements was constructed. When validating the model using standard questionnaire scores of real web pages, high correlations were found between the values computed by the model and scores of questionnaire items related to visual layout of the web pages, indicating that layout-based measures are good at assessing the classical dimension of website aesthetics.

Selective pressures to maintain attachment site specificity of integrative and conjugative elements.

Directory of Open Access Journals (Sweden)

Kayla L Menard

Full Text Available Integrative and conjugative elements (ICEs are widespread mobile genetic elements that are usually found integrated in bacterial chromosomes. They are important agents of evolution and contribute to the acquisition of new traits, including antibiotic resistances. ICEs can excise from the chromosome and transfer to recipients by conjugation. Many ICEs are site-specific in that they integrate preferentially into a primary attachment site in the bacterial genome. Site-specific ICEs can also integrate into secondary locations, particularly if the primary site is absent. However, little is known about the consequences of integration of ICEs into alternative attachment sites or what drives the apparent maintenance and prevalence of the many ICEs that use a single attachment site. Using ICEBs1, a site-specific ICE from Bacillus subtilis that integrates into a tRNA gene, we found that integration into secondary sites was detrimental to both ICEBs1 and the host cell. Excision of ICEBs1 from secondary sites was impaired either partially or completely, limiting the spread of ICEBs1. Furthermore, induction of ICEBs1 gene expression caused a substantial drop in proliferation and cell viability within three hours. This drop was dependent on rolling circle replication of ICEBs1 that was unable to excise from the chromosome. Together, these detrimental effects provide selective pressure against the survival and dissemination of ICEs that have integrated into alternative sites and may explain the maintenance of site-specific integration for many ICEs.

Malazy, a degenerate, species-specific transposable element in Cercospora zeae-maydis.

Science.gov (United States)

Shim, Won-Bo; Dunkle, Larry D

2005-01-01

Two fungal pathogens, Cercospora zeae-maydis Groups I and II, cause gray leaf spot of maize. During the sequencing of a cosmid library from C. zeae-maydis Group I, we discovered a sequence with high similarity to Maggy, a transposable element from Magnaporthe grisea. The element from C. zeae-maydis, named Malazy, contained 194-base-pair terminal repeats and sequences with high similarity to reverse transcriptase and integrase, components of the POL gene in the gypsy-like retrotransposons in fungi. Sequences with similarity to other POL gene components, protease and ribonuclease, were not detected in Malazy. A single copy of the element was detected by PCR and Southern analyses in all six North American isolates of C. zeae-maydis Group I but was not detected in the four isolates of C. zeae-maydis Group II from three continents or in phylogenetically related species. Fragments of the core domains of reverse transcriptase and integrase contained a high frequency of stop codons that were conserved in all six isolates of Group I. Additional C:G to T:A transitions in occasional isolates usually were silent mutations, while two resulted in isolate-specific stop codons. The absence of Malazy from related species suggests that it was acquired after the divergence of C. zeae-maydis Groups I and II. The high frequency of stop codons and the presence of a single copy of the element suggest that it was inactivated soon after it was acquired. Because the element is inactive and because reading frames for other genes were not found in sequences flanking the element, Malazy does not appear to be the cause of differences leading to speciation or genetic diversity between C. zeae-maydis Groups I and II.

Trace element carriers in combined sewer during dry and wet weather: an electron microscope investigation.

Science.gov (United States)

El Samrani, A G; Lartiges, B S; Ghanbaja, J; Yvon, J; Kohler, A

2004-04-01

The nature of trace element carriers contained in sewage and combined sewer overflow (CSO) was investigated by TEM-EDX-Electron diffraction and SEM-EDX. During dry weather, chalcophile elements were found to accumulate in sewer sediments as early diagenetic sulfide phases. The sulfurization of some metal alloys was also evidenced. Other heavy metal carriers detected in sewage include metal alloys, some iron oxihydroxide phases and neoformed phosphate minerals such as anapaite. During rain events, the detailed characterization of individual mineral species allowed to differentiate the contributions from various specific sources. Metal plating particles, barite from automobile brake, or rare earth oxides from catalytic exhaust pipes, originate from road runoff, whereas PbSn alloys and lead carbonates are attributed to zinc-works from roofs and paint from building siding. Soil contribution can be traced by the presence of clay minerals, iron oxihydroxides, zircons and rare earth phosphates. However, the most abundant heavy metal carriers in CSO samples were the sulfide particles eroded from sewer sediments. The evolution of relative abundances of trace element carriers during a single storm event, suggests that the pollution due to the "first flush" effect principally results from the sewer stock of sulfides and previously deposited metal alloys, rather than from urban surface runoff.

Uses of Instrumental Neutron Activation Analysis for Elemental Investigation of Some Domestic Fertilizers

International Nuclear Information System (INIS)

El-Zakla, T.; Abdel Gany, H.A.; Abdel-Aziz, W.M.; Hassan, A.M.; Bashter, I.I.

2010-01-01

The neutron irradiation facilities offered by The Second Egyptian Research Reactor (ETRR-2) and the HPGe-detection system are used for elemental investigation of three samples of domestic fertilizers. A total of 31 elements have been identified as major and minor concentration values. The (PITS) and the core of the reactor are used for short and long time irradiation. The data obtained for some of the identified elements are compared with the corresponding values obtained by the XRF and the ICP-MS techniques for the same samples. The range of the concentration values of these elements was between (several ppm up to 45%). A discussion on the elemental concentration values and their biological effect are given

Evaluation of Populus and Salix continuously irrigated with landfill leachate I. Genotype-specific elemental phytoremediation.

Science.gov (United States)

Zalesny, Ronald S; Bauer, Edmund O

2007-01-01

There is a need for the identification and selection of specific tree genotypes that can sequester elements from contaminated soils, with elevated rates of uptake. We irrigated Populus (DN17, DN182, DN34, NM2, NM6) and Salix (94003, 94012, S287, S566, SX61) genotypes planted in large soil-filled containers with landfill leachate or municipal water and tested for differences in inorganic element concentrations (P, K, Ca, Mg, S, Zn, B, Mn, Fe, Cu, Al, Na, and Cl) in the leaves, stems, and roots. Trees were irrigated with leachate or water during the final 12 wk of the 18-wk study. Genotype-specific uptake existed. For genera, tissue concentrations exhibited four responses. First, Populus had the greatest uptake of P, K, S, Cu, and Cl. Second, Salix exhibited the greatest uptake of Zn, B, Fe, and Al. Third, Salix had greater concentrations of Ca and Mg in leaves, while Populus had greater concentrations in stems and roots. Fourth, Populus had greater concentrations of Mn and Na in leaves and stems, while Salix had greater concentrations in roots. Populus deltoides x P. nigra clones exhibited better overall phytoremediation than the P. nigra x P. maximowiczii genotypes tested. Phytoremediation for S. purpurea clones 94003 and 94012 was generally less than for other Salix genotypes. Overall, concentrations of elements in the leaves, stems, and roots corroborated those in the plant-sciences literature. Uptake was dependent upon the specific genotype for most elements. Our results corroborated the need for further testing and selecting of specific clones for various phytoremediation needs, while providing a baseline for future researchers developing additional studies and resource managers conducting on-site remediation.

Cell type-specific termination of transcription by transposable element sequences.

Science.gov (United States)

Conley, Andrew B; Jordan, I King

2012-09-30

Transposable elements (TEs) encode sequences necessary for their own transposition, including signals required for the termination of transcription. TE sequences within the introns of human genes show an antisense orientation bias, which has been proposed to reflect selection against TE sequences in the sense orientation owing to their ability to terminate the transcription of host gene transcripts. While there is evidence in support of this model for some elements, the extent to which TE sequences actually terminate transcription of human gene across the genome remains an open question. Using high-throughput sequencing data, we have characterized over 9,000 distinct TE-derived sequences that provide transcription termination sites for 5,747 human genes across eight different cell types. Rarefaction curve analysis suggests that there may be twice as many TE-derived termination sites (TE-TTS) genome-wide among all human cell types. The local chromatin environment for these TE-TTS is similar to that seen for 3' UTR canonical TTS and distinct from the chromatin environment of other intragenic TE sequences. However, those TE-TTS located within the introns of human genes were found to be far more cell type-specific than the canonical TTS. TE-TTS were much more likely to be found in the sense orientation than other intragenic TE sequences of the same TE family and TE-TTS in the sense orientation terminate transcription more efficiently than those found in the antisense orientation. Alu sequences were found to provide a large number of relatively weak TTS, whereas LTR elements provided a smaller number of much stronger TTS. TE sequences provide numerous termination sites to human genes, and TE-derived TTS are particularly cell type-specific. Thus, TE sequences provide a powerful mechanism for the diversification of transcriptional profiles between cell types and among evolutionary lineages, since most TE-TTS are evolutionarily young. The extent of transcription

The Drosophila Translational Control Element (TCE is required for high-level transcription of many genes that are specifically expressed in testes.

Directory of Open Access Journals (Sweden)

Rebeccah J Katzenberger

Full Text Available To investigate the importance of core promoter elements for tissue-specific transcription of RNA polymerase II genes, we examined testis-specific transcription in Drosophila melanogaster. Bioinformatic analyses of core promoter sequences from 190 genes that are specifically expressed in testes identified a 10 bp A/T-rich motif that is identical to the translational control element (TCE. The TCE functions in the 5' untranslated region of Mst(3CGP mRNAs to repress translation, and it also functions in a heterologous gene to regulate transcription. We found that among genes with focused initiation patterns, the TCE is significantly enriched in core promoters of genes that are specifically expressed in testes but not in core promoters of genes that are specifically expressed in other tissues. The TCE is variably located in core promoters and is conserved in melanogaster subgroup species, but conservation dramatically drops in more distant species. In transgenic flies, short (300-400 bp genomic regions containing a TCE directed testis-specific transcription of a reporter gene. Mutation of the TCE significantly reduced but did not abolish reporter gene transcription indicating that the TCE is important but not essential for transcription activation. Finally, mutation of testis-specific TFIID (tTFIID subunits significantly reduced the transcription of a subset of endogenous TCE-containing but not TCE-lacking genes, suggesting that tTFIID activity is limited to TCE-containing genes but that tTFIID is not an obligatory regulator of TCE-containing genes. Thus, the TCE is a core promoter element in a subset of genes that are specifically expressed in testes. Furthermore, the TCE regulates transcription in the context of short genomic regions, from variable locations in the core promoter, and both dependently and independently of tTFIID. These findings set the stage for determining the mechanism by which the TCE regulates testis-specific transcription and

The Drosophila Translational Control Element (TCE) is required for high-level transcription of many genes that are specifically expressed in testes.

Science.gov (United States)

Katzenberger, Rebeccah J; Rach, Elizabeth A; Anderson, Ashley K; Ohler, Uwe; Wassarman, David A

2012-01-01

To investigate the importance of core promoter elements for tissue-specific transcription of RNA polymerase II genes, we examined testis-specific transcription in Drosophila melanogaster. Bioinformatic analyses of core promoter sequences from 190 genes that are specifically expressed in testes identified a 10 bp A/T-rich motif that is identical to the translational control element (TCE). The TCE functions in the 5' untranslated region of Mst(3)CGP mRNAs to repress translation, and it also functions in a heterologous gene to regulate transcription. We found that among genes with focused initiation patterns, the TCE is significantly enriched in core promoters of genes that are specifically expressed in testes but not in core promoters of genes that are specifically expressed in other tissues. The TCE is variably located in core promoters and is conserved in melanogaster subgroup species, but conservation dramatically drops in more distant species. In transgenic flies, short (300-400 bp) genomic regions containing a TCE directed testis-specific transcription of a reporter gene. Mutation of the TCE significantly reduced but did not abolish reporter gene transcription indicating that the TCE is important but not essential for transcription activation. Finally, mutation of testis-specific TFIID (tTFIID) subunits significantly reduced the transcription of a subset of endogenous TCE-containing but not TCE-lacking genes, suggesting that tTFIID activity is limited to TCE-containing genes but that tTFIID is not an obligatory regulator of TCE-containing genes. Thus, the TCE is a core promoter element in a subset of genes that are specifically expressed in testes. Furthermore, the TCE regulates transcription in the context of short genomic regions, from variable locations in the core promoter, and both dependently and independently of tTFIID. These findings set the stage for determining the mechanism by which the TCE regulates testis-specific transcription and understanding the

Uses of instrumental neutron activation analysis for elemental investigation of some domestic fertilizers

Directory of Open Access Journals (Sweden)

A. M. Hassan

2008-12-01

Full Text Available The neutron irradiation facilities offered by the ET-RR-2 and the HPGe-detection system are used for elemental investigation of three samples of domestic fertilizers. A total of 31 elements have been identified as major and minor concentration values. The Pneumatic Irradiation Transfer Systems (PITS and the core of the reactor are used for short and long time irradiation. The data obtained for some of the identified elements are compared with the corresponding values obtained by the XRF and the ICP-MS techniques for the same samples. The range of the concentration values of these elements was in between several parts per million (ppm up to 45 %. A discussion on the elemental concentration values and their biological effect are given.

PCMO L01-Setting Specifications for Biological Investigational Medicinal Products.

Science.gov (United States)

Krause, Stephan O

2015-01-01

This paper provides overall guidance and best practices for the setting of specifications for clinical biological drug substances and drug products within the framework of ICH guidelines on pharmaceutical development [Q8(R2) and Q11], quality risk management (Q9), and quality systems (Q10). A review is provided of the current regulatory expectations for the specification setting process as part of a control strategy during product development, pointing to existing challenges for the investigational new drug/investigational medicinal product dossier (IND/IMPD) sponsor. A case study illustrates how the investigational medicinal product specification revision process can be managed within a flexible quality system, and how specifications can be set and justified for early and late development stages. This paper provides an overview for the setting of product specifications for investigational medicinal products used in clinical trials. A case study illustrates how product specifications of investigational medicinal products can be justified and managed within a modern product quality system. © PDA, Inc. 2015.

Cell type-specific termination of transcription by transposable element sequences

Directory of Open Access Journals (Sweden)

Conley Andrew B

2012-09-01

Full Text Available Abstract Background Transposable elements (TEs encode sequences necessary for their own transposition, including signals required for the termination of transcription. TE sequences within the introns of human genes show an antisense orientation bias, which has been proposed to reflect selection against TE sequences in the sense orientation owing to their ability to terminate the transcription of host gene transcripts. While there is evidence in support of this model for some elements, the extent to which TE sequences actually terminate transcription of human gene across the genome remains an open question. Results Using high-throughput sequencing data, we have characterized over 9,000 distinct TE-derived sequences that provide transcription termination sites for 5,747 human genes across eight different cell types. Rarefaction curve analysis suggests that there may be twice as many TE-derived termination sites (TE-TTS genome-wide among all human cell types. The local chromatin environment for these TE-TTS is similar to that seen for 3′ UTR canonical TTS and distinct from the chromatin environment of other intragenic TE sequences. However, those TE-TTS located within the introns of human genes were found to be far more cell type-specific than the canonical TTS. TE-TTS were much more likely to be found in the sense orientation than other intragenic TE sequences of the same TE family and TE-TTS in the sense orientation terminate transcription more efficiently than those found in the antisense orientation. Alu sequences were found to provide a large number of relatively weak TTS, whereas LTR elements provided a smaller number of much stronger TTS. Conclusions TE sequences provide numerous termination sites to human genes, and TE-derived TTS are particularly cell type-specific. Thus, TE sequences provide a powerful mechanism for the diversification of transcriptional profiles between cell types and among evolutionary lineages, since most TE-TTS are

Investigation of elemental distribution in lung samples by X-ray fluorescence microtomography

International Nuclear Information System (INIS)

Pereira, Gabriela R.; Rocha, Henrique S.; Lopes, Ricardo T.

2007-01-01

X-Ray Fluorescence Microtomography (XRFCT) is a suitable technique to find elemental distributions in heterogeneous samples. While x-ray transmission microtomography provides information about the linear attenuation coefficient distribution, XRFCT allows one to map the most important elements in the sample. The x-ray fluorescence tomography is based on the use of the X-ray fluorescence emitted from the elements contained in a sample so as to give additional information to characterize the object under study. In this work a rat lung and two human lung tissue samples have been investigated in order to verify the efficiency of the system in determination of the internal distribution of detected elements in these kinds of samples and to compare the elemental distribution in the lung tissue of an old human and a fetus. The experiments were performed at the X-Ray Fluorescence beamline (XRF) of the Brazilian Synchrotron Light Source (LNLS), Campinas, Brazil. A white beam was used for the excitation of the elements and the fluorescence photons have been detected by a HPGe detector. All the tomographies have been reconstructed using a filtered-back projection algorithm. It was possible to visualize the distribution of high atomic number elements on both, artificial and tissues samples. It was compared the quantity of Zn, Cu and Fe for the lung human tissue samples and verify that these elements have a higher concentration on the fetus tissue sample than the adult tissue sample. (author)

Review of element-specific data for biosphere assessment BSA-2009

International Nuclear Information System (INIS)

Helin, J.; Ikonen, A. T. K.; Hjerpe, T.

2010-06-01

A literature review on distribution coefficients (Kd) to soil, sediment and suspended matter and on concentration ratios to forest, aquatic and crop plants and to edibles was performed and is documented in this report. The literature data were combined, in some cases involving also site-specific data, using the methods of Bayesian updating. Their application is also explained in the report. Based on the derived data, aggregated concentration ratios (production-weighted average concentration ratio to edibles specific to an ecosystem type) were calculated. Finally, the quality of the established data basis is evaluated. The work provides the 2009 biosphere assessment of spent nuclear fuel disposal the in Olkiluoto site, BSA-2009, with the abovementioned parameter values and distributions, but most importantly demonstrates the methodology adopted to combine various data sources and derive such assessment data. It is acknowledged that for many parameters and/or elements the data basis needs improvement by the forthcoming 2012 assessment. (orig.)

Investigation of High-Speed Cryogenic Machining Based on Finite Element Approach

Directory of Open Access Journals (Sweden)

Pooyan Vahidi Pashaki

Full Text Available Abstract The simulation of cryogenic machining process because of using a three-dimensional model and high process duration time in the finite element method, have been studied rarely. In this study, to overcome this limitation, a 2.5D finite element model using the commercial finite element software ABAQUS has been developed for the cryogenic machining process and by considering more realistic assumptions, the chip formation procedure investigated. In the proposed method, the liquid nitrogen has been used as a coolant. At the modeling of friction during the interaction of tools - chip, the Coulomb law has been used. In order to simulate the behavior of plasticity and failure criterion, Johnson-Cook model was used, and unlike previous investigations, thermal and mechanical properties of materials as a function of temperature were applied to the software. After examining accuracy of the model with present experimental data, the effect of parameters such as rake angle and the cutting speed as well as dry machining of aluminum alloy by the use of coupled dynamic temperature solution has been studied. Results indicated that at the cutting velocity of 10 m/s, cryogenic cooling has caused into decreasing 60 percent of tools temperature in comparison with the dry cooling. Furthermore, a chip which has been made by cryogenic machining were connected and without fracture in contrast to dry machining.

Investigating Planetesimal Evolution by Experiments with Fe-Ni Metallic Melts: Light Element Composition Effects on Trace Element Partitioning Behavior

Science.gov (United States)

Chabot, N. L.

2017-12-01

As planetesimals were heated up in the early Solar System, the formation of Fe-Ni metallic melts was a common occurrence. During planetesimal differentiation, the denser Fe-Ni metallic melts separated from the less dense silicate components, though some meteorites suggest that their parent bodies only experienced partial differentiation. If the Fe-Ni metallic melts did form a central metallic core, the core eventually crystallized to a solid, some of which we sample as iron meteorites. In all of these planetesimal evolution processes, the composition of the Fe-Ni metallic melt influenced the process and the resulting trace element chemical signatures. In particular, the metallic melt's "light element" composition, those elements present in the metallic melt in a significant concentration but with lower atomic masses than Fe, can strongly affect trace element partitioning. Experimental studies have provided critical data to determine the effects of light elements in Fe-Ni metallic melts on trace element partitioning behavior. Here I focus on combining numerous experimental results to identify trace elements that provide unique insight into constraining the light element composition of early Solar System Fe-Ni metallic melts. Experimental studies have been conducted at 1 atm in a variety of Fe-Ni systems to investigate the effects of light elements on trace element partitioning behavior. A frequent experimental examination of the effects of light elements in metallic systems involves producing run products with coexisting solid metal and liquid metal phases. Such solid-metal-liquid-metal experiments have been conducted in the Fe-Ni binary system as well as Fe-Ni systems with S, P, and C. Experiments with O-bearing or Si-bearing Fe-Ni metallic melts do not lend themselves to experiments with coexisting solid metal and liquid metal phases, due to the phase diagrams of these elements, but experiments with two immiscible Fe-Ni metallic melts have provided insight into

Finite element investigation of explosively formed projectiles (EFP)

International Nuclear Information System (INIS)

Ahmad, I.

1999-01-01

This thesis report represents the numerical simulation of explosively formed projectiles (EFP), a type of linear self-forging fragment device. The simulation is performed using a finite element code DYNA2D. It also explicates that how the shape, velocity and kinetic energy of an explosively formed projectile is effected by various parameters. Different parameters investigated are mesh density, material, thickness, contour and types of liner. Effect of shape of casing and material model is also analyzed. The shapes of projectiles at different times after detonation are shown. The maximum velocity and kinetic energy of the projectile have been used to ascertain the effect of above mentioned parameters. (author)

Numerical Investigations on Several Stabilized Finite Element Methods for the Stokes Eigenvalue Problem

Directory of Open Access Journals (Sweden)

Pengzhan Huang

2011-01-01

Full Text Available Several stabilized finite element methods for the Stokes eigenvalue problem based on the lowest equal-order finite element pair are numerically investigated. They are penalty, regular, multiscale enrichment, and local Gauss integration method. Comparisons between them are carried out, which show that the local Gauss integration method has good stability, efficiency, and accuracy properties, and it is a favorite method among these methods for the Stokes eigenvalue problem.

Elemental investigation of momordica charantia linn. and syzigium jambolana linn. using atomic absorption spectrophotometer

International Nuclear Information System (INIS)

Kazi, T.G.

2002-01-01

Elemental investigation of very important medicinal plant i.e. momordica charantia linn and syzigium jambolana linn, and its decoction has been carried out using flame atomic absorption spectrophotometer. In present study fifteen essential, trace and toxic elements such as Zn, Cr, K, Mg, Ca, Na, Cu, Fe, Pb, Al, Ba, Mn, Co, Ni and Cd were determined in different parts of both plants and in its decoction. The level of essential elements was found high as compared to the level of toxic elements. Both plants are useful in the treatment of diabetes. The validation of the method was checked by employing NBS- 1570 (Spanish) as a standard reference material . The measured values of elements are in close agreement with certified values. (author)

Dietary investigation by trace element content in bones of ancient inhabitants of Northern Italy

International Nuclear Information System (INIS)

Busetto, M.; Giordani, L.; Brandone, A.; Cattaneo, C.; Mazzucchi, A.

2008-01-01

Bone is an important mineral source for the entire organism especially for Ca, P, Na and trace elements like Sr, Mg, Zn and it is the reservoir for the storage and mobilization of many important ions required for the metabolic activity of the organism. The concentration of these elements are influenced by the individual diet and the content of some trace elements can be utilized as indicators of the diet of ancient populations. Bones from three differents archaeological sites found in Lombardy, Northern Italy, were investigated: (A) Roman necropolis found in Milan active from the 1st century B.C. to the 2nd century A.D; (B) Burial of the Longobard family found in Campione d'Italia (North of Lombardy) active between the 7th and 9th century A.D.; (C) Medieval necropolis of a Longobard community, found in a village near Cremona (SE of Lombardy) active in the 7th century A.D. Structures of bones and their trace element content seem to put in evidence on some differences in the way of life of the three investigated groups. (author)

Atlas-Based Automatic Generation of Subject-Specific Finite Element Tongue Meshes.

Science.gov (United States)

Bijar, Ahmad; Rohan, Pierre-Yves; Perrier, Pascal; Payan, Yohan

2016-01-01

Generation of subject-specific 3D finite element (FE) models requires the processing of numerous medical images in order to precisely extract geometrical information about subject-specific anatomy. This processing remains extremely challenging. To overcome this difficulty, we present an automatic atlas-based method that generates subject-specific FE meshes via a 3D registration guided by Magnetic Resonance images. The method extracts a 3D transformation by registering the atlas' volume image to the subject's one, and establishes a one-to-one correspondence between the two volumes. The 3D transformation field deforms the atlas' mesh to generate the subject-specific FE mesh. To preserve the quality of the subject-specific mesh, a diffeomorphic non-rigid registration based on B-spline free-form deformations is used, which guarantees a non-folding and one-to-one transformation. Two evaluations of the method are provided. First, a publicly available CT-database is used to assess the capability to accurately capture the complexity of each subject-specific Lung's geometry. Second, FE tongue meshes are generated for two healthy volunteers and two patients suffering from tongue cancer using MR images. It is shown that the method generates an appropriate representation of the subject-specific geometry while preserving the quality of the FE meshes for subsequent FE analysis. To demonstrate the importance of our method in a clinical context, a subject-specific mesh is used to simulate tongue's biomechanical response to the activation of an important tongue muscle, before and after cancer surgery.

Determination of the element-specific complex permittivity using a soft x-ray phase modulator

Science.gov (United States)

Kubota, Y.; Hirata, Y.; Miyawaki, J.; Yamamoto, S.; Akai, H.; Hobara, R.; Yamamoto, Sh.; Yamamoto, K.; Someya, T.; Takubo, K.; Yokoyama, Y.; Araki, M.; Taguchi, M.; Harada, Y.; Wadati, H.; Tsunoda, M.; Kinjo, R.; Kagamihata, A.; Seike, T.; Takeuchi, M.; Tanaka, T.; Shin, S.; Matsuda, I.

2017-12-01

We report on directly determining the complex permittivity tensor using a method combining a developed light source from a segmented cross undulator of synchrotron radiation and the magneto-optical Kerr effect. The empirical permittivity, which carries the electronic and magnetic information of a material, has element specificity and has perfect confirmation using the quantum-mechanical calculation for itinerant electrons systems. These results help in understanding the interaction of light and matter, and they provide an interesting approach to seek the best materials as optical elements, for example, in extended-ultraviolet lithographic technologies or in state-of-the-art laser technologies.

Synthesis and investigation of superheavy elements - perspectives with radioactive beams

International Nuclear Information System (INIS)

Muenzenberg, G.

1997-09-01

The perspectives for the investigation of heavy and superheavy elements with intense beams of radioactive nuclei available from the new generation of secondary beam facilities in combination with modern experimental developments are the subject of this paper. The nuclear properties of the recently discovered shell nuclei centered at Z=108 and N=164 and predictions on the location of the superheavy region with improved theoretical models will be discussed. (orig.)

Investigations for chromatographic separation and determination of the rare earths and auxiliary group elements

International Nuclear Information System (INIS)

Post, K.

1981-01-01

Different method have been developed to quantitatively determine rare earth elements after their column chromatographic separation. The influence of the active solvents in the running systems diethyl ether/tetra hydrofuran (THF)/nitric acid (HNO 3 ) and diethyl ether/bis-(2-ethyl hexyl) phosphate (HDEHP)/HNO 3 was investigated on the column chromatographic separation of all rare earth elements is possible by the synergistic combination of the active running components THF and HDEHP. Further from product isotopes could also be separated using the running agents described here in investigations to separate fission product mixtures of irradiated uranium. (orig./HBR) [de

AN INVESTIGATIVE STUDY REGARDING SMES SPECIFIC ACCOUNTING POLICIES

Directory of Open Access Journals (Sweden)

Mester Ioana Teodora

2011-07-01

Full Text Available In this paper we intend to continue the research regarding the enterprise accounting policies and the manner in which these are perceived by the practitioner accountants, preparers of financial statements. This time, in order to carry out the research, we made up a new questionnaire applied to the same sample, containing a number of 100 SMEs in Bihor County, selected according to the criterion of the average number of employees and that of the level of net turnover at the end of 2008. Continuing previous conducted research we have investigated this time the specific accounting policies of the sampled SMEs from Bihor County and the way these policies are understood by practitioners and implemented in order to prepare financial statements. Surprisingly, we have found that only 93.33% of the respondents agree that the elements presented in the annual financial statements of the entity are evaluated in accordance with the general accounting principles stipulated in Order 3055/2009, according to the accrual accounting. Half of the people interviewed had in view all four qualities of accounting information (intelligibility, relevance, credibility, comparability in drawing up the annual financial statements, and most of them (56.67% are not aware of the possibility to use a significance threshold (10%-15% of the total value of that particular category of assets, liabilities, expenditure, income and results for an as faithful as possible presentation of information in the balance sheet and in the profit and loss account.

Chemical analysis of the elements in UZrNb alloy at CDTN: preliminary investigation

International Nuclear Information System (INIS)

Ferraz, Wilmar Barbosa; Palmieri, Helena Eugenia L.; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos; Souza, Adalberto Leles de

2012-01-01

The complete determination of major, minor, and impurity element contents in nuclear fuel is essential for quality assurance in the production of nuclear fuels. The control over all the stages of the development of nuclear fuel involves a combination of different analytical methods such as spectrometric methods. The goal of our investigation is to develop and evaluate procedures for the determination of main elements and carbon impurity present in some uranium alloys. In this paper the element contents in U2.5Zr7.5Nb, U3Zr9Nb alloys and U6Nb, in weight percent, were investigated by means of scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDS), inductively coupled plasma mass spectrometry (ICP-MS), wavelength dispersive fluorescence spectrometry (XRF/WDS) and energy-dispersive X-ray spectroscopy (EDX). The total carbon was determined using a carbon analyzer in which the sample is oxidized to carbon dioxide (IR absorption). It was observed a satisfactory correlation between the results obtained by employed methods. (author)

Functional dissection of a napin gene promoter: identification of promoter elements required for embryo and endosperm-specific transcription.

Science.gov (United States)

Ellerström, M; Stålberg, K; Ezcurra, I; Rask, L

1996-12-01

The promoter region (-309 to +44) of the Brassica napus storage protein gene napA was studied in transgenic tobacco by successive 5' as well as internal deletions fused to the reporter gene GUS (beta-glucuronidase). The expression in the two main tissues of the seed, the endosperm and the embryo, was shown to be differentially regulated. This tissue-specific regulation within the seed was found to affect the developmental expression during seed development. The region between -309 to -152, which has a large effect on quantitative expression, was shown to harbour four elements regulating embryo and one regulating endosperm expression. This region also displayed enhancer activity. Deletion of eight bp from position -152 to position -144 totally abolished the activity of the napA promoter. This deletion disrupted a cis element with similarity to an ABA-responsive element (ABRE) overlapping with an E-box, demonstrating its crucial importance for quantitative expression. An internal deletion of the region -133 to -120, resulted in increased activity in both leaves and endosperm and a decreased activity in the embryo. Within this region, a cis element similar to the (CA)n element, found in other storage protein promoters, was identified. This suggest that the (CA)n element is important for conferring seed specificity by serving both as an activator and a repressor element.

Probabilistic finite element investigation of prestressing loss in nuclear containment wall segments

International Nuclear Information System (INIS)

Balomenos, Georgios P.; Pandey, Mahesh D.

2017-01-01

Highlights: • Probabilistic finite element framework for assessing concrete strain distribution. • Investigation of prestressing loss based on concrete strain distribution. • Application to 3D nuclear containment wall segments. • Use of ABAQUS with python programing for Monte Carlo simulation. - Abstract: The main function of the concrete containment structures is to prevent radioactive leakage to the environment in case of a loss of coolant accident (LOCA). The Canadian Standard CSA N287.6 (2011) proposes periodic inspections, i.e., pressure testing, in order to assess the strength and design criteria of the containment (proof test) and the leak tightness of the containment boundary (leakage rate test). During these tests, the concrete strains are measured and are expected to have a distribution due to several uncertainties. Therefore, this study aims to propose a probabilistic finite element analysis framework. Then, investigates the relationship between the concrete strains and the prestressing loss, in order to examine the possibility of estimating the average prestressing loss during pressure testing inspections. The results indicate that the concrete strain measurements during the leakage rate test may provide information with respect to the prestressing loss of the bonded system. In addition, the demonstrated framework can be further used for the probabilistic finite element analysis of real scale containments.

Probabilistic finite element investigation of prestressing loss in nuclear containment wall segments

Energy Technology Data Exchange (ETDEWEB)

Balomenos, Georgios P., E-mail: gbalomen@uwaterloo.ca; Pandey, Mahesh D., E-mail: mdpandey@uwaterloo.ca

2017-01-15

Highlights: • Probabilistic finite element framework for assessing concrete strain distribution. • Investigation of prestressing loss based on concrete strain distribution. • Application to 3D nuclear containment wall segments. • Use of ABAQUS with python programing for Monte Carlo simulation. - Abstract: The main function of the concrete containment structures is to prevent radioactive leakage to the environment in case of a loss of coolant accident (LOCA). The Canadian Standard CSA N287.6 (2011) proposes periodic inspections, i.e., pressure testing, in order to assess the strength and design criteria of the containment (proof test) and the leak tightness of the containment boundary (leakage rate test). During these tests, the concrete strains are measured and are expected to have a distribution due to several uncertainties. Therefore, this study aims to propose a probabilistic finite element analysis framework. Then, investigates the relationship between the concrete strains and the prestressing loss, in order to examine the possibility of estimating the average prestressing loss during pressure testing inspections. The results indicate that the concrete strain measurements during the leakage rate test may provide information with respect to the prestressing loss of the bonded system. In addition, the demonstrated framework can be further used for the probabilistic finite element analysis of real scale containments.

Verklarende prediking. Basisteoretiese elemente uit Hebreërs

Directory of Open Access Journals (Sweden)

C.J.H. Venter

2001-08-01

Full Text Available Expository preaching. Basis-theoretical elements from Hebrews This article specifically focuses on basis-theoretical elements in the Letter to the Hebrews – a New Testament book that can actually be regarded as a sermon. In the introduction the point of departure, that is the focus on bais-theoretical elements, is justified. Furthermore, attention is paid to specific elements of preaching implied in this “sermon” in the Letter to the Hebrews: elements applicable to the practice of expository preaching, the structure in an expository sermon, that is the introduction, the body, and the conclusion. The purpose of the sermon is also touched upon. Issues like the spirituality of the preacher, his ministry of equipping by means of expository preaching, and his relationship to the congregation are also investigated, followed by final conclusions.

Development of the methodology on priority of element-specific biosphere parameters for geological disposal applicable to any proposed repository site

International Nuclear Information System (INIS)

Kato, Tomoko; Ohi, Takao; Suzuki, Yuji

2009-01-01

It is difficult to acquire all of biosphere parameters for geological disposal at the repository site because several hundreds of the parameters have to be dealt with in one calculation case of the biosphere assessment. Before site-specific activities, it is important to develop the data acquisition methodology of biosphere parameters applicable to any proposed repository site. The methodology for identification of the priority of the parameters was developed for the effective data acquisition of biosphere parameters at the site. First of all, flow diagram was constructed to evaluate the availability of the existing generic biosphere dataset. It was found to be effective for the data acquisition at the site to focus on the element-specific parameters with the existing dataset. Secondly, the priority of the data acquisition was identified for element-specific parameters at the site, with considering the variation of dose rate by combining the significant element-specific parameters. The availability of the existing generic biosphere dataset and the priority on data acquisition were identified for the element-specific parameters of key radionuclides in the safety assessment of geological disposal that should be acquired at the site. This priority list would be useful for effective data acquisition at the site. (author)

Morphing methods to parameterize specimen-specific finite element model geometries.

Science.gov (United States)

Sigal, Ian A; Yang, Hongli; Roberts, Michael D; Downs, J Crawford

2010-01-19

Shape plays an important role in determining the biomechanical response of a structure. Specimen-specific finite element (FE) models have been developed to capture the details of the shape of biological structures and predict their biomechanics. Shape, however, can vary considerably across individuals or change due to aging or disease, and analysis of the sensitivity of specimen-specific models to these variations has proven challenging. An alternative to specimen-specific representation has been to develop generic models with simplified geometries whose shape is relatively easy to parameterize, and can therefore be readily used in sensitivity studies. Despite many successful applications, generic models are limited in that they cannot make predictions for individual specimens. We propose that it is possible to harness the detail available in specimen-specific models while leveraging the power of the parameterization techniques common in generic models. In this work we show that this can be accomplished by using morphing techniques to parameterize the geometry of specimen-specific FE models such that the model shape can be varied in a controlled and systematic way suitable for sensitivity analysis. We demonstrate three morphing techniques by using them on a model of the load-bearing tissues of the posterior pole of the eye. We show that using relatively straightforward procedures these morphing techniques can be combined, which allows the study of factor interactions. Finally, we illustrate that the techniques can be used in other systems by applying them to morph a femur. Morphing techniques provide an exciting new possibility for the analysis of the biomechanical role of shape, independently or in interaction with loading and material properties. Copyright 2009 Elsevier Ltd. All rights reserved.

Finite element investigations on the microstructure of fibre-reinforced composites

Directory of Open Access Journals (Sweden)

2008-09-01

Full Text Available The effect of residual stress due to the curing process on damage evolution in unidirectional (UD fibre-reinforced polymer-matrix composites under longitudinal and transverse loading has been investigated using a three-dimensional micromechanical representative volume element (RVE model with a hexagonal packing geometry and the finite element method. Residual stress has been determined by considering two contributions: volume shrinkage of matrix resin from the crosslink polymerization during isothermal curing and thermal contraction of both resin and fibre as a result of cooling from the curing temperature to room temperature. To examine the effect of residual stress on failure, a study based on different failure criteria and a stiffness degradation technique has been used for damage analysis of the RVE subjected to mechanical loading after curing for a range of fibre volume fractions. Predicted damage initiation and evolution are clearly influenced by the presence of residual stress.

Investigations of trace element profiles in e-waste by EDXRF

International Nuclear Information System (INIS)

Joseph, Daisy; Polumi; Kale, S.K.

2010-01-01

Full text: Electronic waste, e-waste, e-scrap, or Waste Electrical and Electronic Equipment (WEEE) which means loosely discarded, surplus, obsolete, or broken electrical or electronic devices is good source of toxins in atmosphere. Environmental groups claim that the informal processing of electronic waste in developing countries causes serious health and pollution problems. Some electronic scrap components, contain contaminants such as lead, cadmium, beryllium, mercury, and brominated flame retardants. Activists claim that even in developed countries recycling and disposal of e-waste may involve significant risk to workers and communities and great care must be taken to avoid unsafe exposure in recycling operations and leaching of material such as heavy metals. Scrap industry and USA EPA officials agree that materials should be managed with caution, but that environmental dangers of unused electronics have been exaggerated by groups which benefit from increased regulation. To solve this debatable issue we have carried out EDXFR of e-waste for trace elemental profile investigations. E-waste from IT industry in the form of powder was analyzed by 109 Cd induced Energy Dispersive X-ray fluorescence. Elements such as Ca, Fe, Br, Sr and Zr were seen. The trace element significance of e-waste and its correlation to environmental toxicity is being looked into

Investigation of element distributions in Luna-16 regolith

Science.gov (United States)

Kuznetsov, R. A.; Lure, B. G.; Minevich, V. Ia.; Stiuf, V. I.; Pankratov, V. B.

1981-03-01

The concentrations of 32 elements in fractions of different grain sizes in the samples of the lunar regolith brought back by Luna-16 are determined by means of neutron activation analysis. Four groups of elements are distinguished on the basis of the variations of their concentration with grain size, and concentration variations of the various elements with sample depth are also noted. Chemical leaching of the samples combined with neutron activation also reveals differences in element concentrations in the water soluble, metallic, sulphide, phosphate, rare mineral and rock phases of the samples. In particular, the rare earth elements are observed to be depleted in the regolith with respect to chondritic values, and to be concentrated in the phase extracted with 14 M HNO3.

Age- and sex-specific thorax finite element model development and simulation.

Science.gov (United States)

Schoell, Samantha L; Weaver, Ashley A; Vavalle, Nicholas A; Stitzel, Joel D

2015-01-01

The shape, size, bone density, and cortical thickness of the thoracic skeleton vary significantly with age and sex, which can affect the injury tolerance, especially in at-risk populations such as the elderly. Computational modeling has emerged as a powerful and versatile tool to assess injury risk. However, current computational models only represent certain ages and sexes in the population. The purpose of this study was to morph an existing finite element (FE) model of the thorax to depict thorax morphology for males and females of ages 30 and 70 years old (YO) and to investigate the effect on injury risk. Age- and sex-specific FE models were developed using thin-plate spline interpolation. In order to execute the thin-plate spline interpolation, homologous landmarks on the reference, target, and FE model are required. An image segmentation and registration algorithm was used to collect homologous rib and sternum landmark data from males and females aged 0-100 years. The Generalized Procrustes Analysis was applied to the homologous landmark data to quantify age- and sex-specific isolated shape changes in the thorax. The Global Human Body Models Consortium (GHBMC) 50th percentile male occupant model was morphed to create age- and sex-specific thoracic shape change models (scaled to a 50th percentile male size). To evaluate the thoracic response, 2 loading cases (frontal hub impact and lateral impact) were simulated to assess the importance of geometric and material property changes with age and sex. Due to the geometric and material property changes with age and sex, there were observed differences in the response of the thorax in both the frontal and lateral impacts. Material property changes alone had little to no effect on the maximum thoracic force or the maximum percent compression. With age, the thorax becomes stiffer due to superior rotation of the ribs, which can result in increased bone strain that can increase the risk of fracture. For the 70-YO models

Investigation on concentration of elements in wetland sediments and aquatic plants

Directory of Open Access Journals (Sweden)

H. Janadeleh

2016-01-01

Full Text Available The major aim of the present study was to investigate element (Fe, Ni, Pb, V, Zn concentrations in sediment and different tissues of Phragmities australis and Typha latifolia in Hor al-Azim Wetland Southwest Iran. Sampling of sediments and aquatic plants was carried out during spring and summer 2014. Results showed that the mean  concentrations of elements in Phragmities australis  in root and stem-leaf were as follows: Iron:4448 mg/kg, Nickel: 28 mg/kg, Lead:8 mg/kg, Vanadium:10 mg/kg  and Zinc 15.5 mg/kg in root and: Fe:645 mg/kg, Ni:15 mg/kg, Pb:4 mg/kg, V:4 mg/kg and Zinc 16 mg/kg respectively. Also, the mean concentrations of Fe, Ni, Pb, V and Zn in roots of Typha latifolia were 8696 mg/kg, 34 mg/kg, 5 mg/kg, 19 mg/kg and 27 mg/kg respectively. The mean concentrations of Fe, Ni, V, Pb, Zn in stem-leaves of Typha latifolia were as follows: 321 mg/kg, 3 mg/kg, 7 mg/kg, 2 mg/kg and 14 mg/kg respectively. The mean concentrations of Fe, Ni, V, Pb and zinc were as: 40991 mg/kg, 65 mg/kg, 60 mg/kg, 31 mg/kg, 60 mg/kg respectively in surface sediment of study area. Concentration pattern of elements in sediment were as: Fe>Ni>Zn>V>Pb. The highest concentration of elements in the plant was seen in the roots. Also, Typha latifolia can uptake more concentration of elements than Phragmities australis. Based on the enrichment factor, Ni in summer had the highest EF values among the elements studied and it has a moderate enrichment.

Investigation of Redistribution of Pile Foundation Forces Under Successive Loading of Its Elements

Science.gov (United States)

Sedin, Vladimir; Bikus, Kateryna; Kovba, Vladislav

2017-12-01

Redistribution of pile foundation forces under successive loading of its elements was investigated under laboratory conditions. A segment of pile foundation model was taken for use in the case study. Load tests on the pile foundation model segment, without joining its elements (pile and plate, which turns into grillage) and based on different combinations of static loadings were conducted. This proved that the loading of a plate causes skin friction on some length of the pile side surface as well as providing additional loading and settlement. Test results have shown that application of successive elements enables the foundation to carry loads up to 13% higher than in the case of a standard pile foundation loading with the same settlement rates.

NUMERICAL INVESTIGATION OF TWO ELEMENT CAMBER MORPHING AIRFOIL IN LOW REYNOLDS NUMBER FLOWS

OpenAIRE

RAJESH SENTHIL KUMAR T.; V. SIVAKUMAR; BALAJEE RAMAKRISHNANANDA; ARJHUN A.K, SURIYAPANDIYAN

2017-01-01

Aerodynamic performance of a two-element camber morphing airfoil was investigated at low Reynolds number using the transient SST model in ANSYS FLUENT 14.0 and eN method in XFLR5. The two-element camber morphing concept was employed to morph the baseline airfoil into another airfoil by altering the orientation of mean-line at 35% of the chord to achieve better aerodynamic efficiency. NACA 0012 was selected as baseline airfoil. NACA 23012 was chosen as the test case as it has the camber-line s...

Stability of hydrophilic vitamins mixtures in the presence of electrolytes and trace elements for parenteral nutrition: a nuclear magnetic resonance spectroscopy investigation.

Science.gov (United States)

Uccello-Barretta, Gloria; Balzano, Federica; Aiello, Federica; Falugiani, Niccolò; Desideri, Ielizza

2015-03-25

In total parenteral nutrition (TPN), especially in the case of preterm infants, simultaneous administration of vitamins and trace elements is still a problematic issue: guidelines put in evidence the lack of specific documentation. In this work NMR spectroscopy was applied to the study of vitamins (pyridoxine hydrochloride, thiamine nitrate, riboflavin-5'-phosphate and nicotinamide) stability in presence of salts and trace elements. Vitamins in D2O were first analyzed by (1)H NMR spectroscopy in absence of salts and trace elements; changes in chemical shifts or in diffusion coefficients, measured by NMR DOSY technique, were analyzed. The effects of salts and trace elements on single vitamins and on their admixtures were then investigated by performing quantitative analyses during 48h. Selected vitamins are subject to intermolecular interactions. No degradative effects were observed in presence of salts and trace elements. Only riboflavin-5'-phosphate is subject to precipitation in presence of divalent cations; however, at low concentration and in presence of other vitamins this effect was not observed. Solutions analyzed, in the condition of this study, are stable for at least 48h and vitamins and trace elements can be administered together in TPN. Copyright © 2014 Elsevier B.V. All rights reserved.

Investigation of turbulent wedges generated by different single surface roughness elements

Science.gov (United States)

Traphan, Dominik; Meinlschmidt, Peter; Lutz, Otto; Peinke, Joachim; Gülker, Gerd

2013-11-01

It is known that small faults on rotor blades of wind turbines can cause significant power loss. In order to better understand the governing physical effects, in this experimental study, the formation of a turbulent wedge over a flat plate induced by single surface roughness elements is under investigation. The experiments are performed at different ambient pressure gradients, thus allowing conclusions about the formation of a turbulent wedge over an airfoil. With respect to typical initial faults on operating airfoils, the roughness elements are modified in both size and shape (raised or recessed). None intrusive experimental methods, such as stereoscopic PIV and LDA, enable investigations based on temporally and spatially highly resolved velocity measurements. In this way, a spectral analysis of the turbulent boundary layer is performed and differences in coherent structures within the wedge are identified. These findings are correlated with global measurements of the wedge carried out by infrared thermography. This correlation aims to enable distinguishing the cause and main properties of a turbulent wedge by the easy applicable method of infrared thermography, which is of practical relevance in the field of condition monitoring of wind turbines.

The Investigation of the Element Contents in the Turkish Coffees

OpenAIRE

Demir, Funda; Selvi, Nigar; Kıpçak, Seyhun; Özdemir, Özgül; Piskin, Mehmet; Moroydor Derun, Emek

2015-01-01

The Investigation of the Element Contents in the Turkish CoffeesCoffee is one of the most popular drinks across the world and its enormous commercial and social importance is obvious. Coffee has become the essential consumption matter and one of the rituals of many societies for several years.Turkish people's first confrontation with it dates back to 16th century, in Ottoman era. Since then, because of the differences in terms of preparation and presentation styles, the coffee has been n...

Investigation of rare elements by electrochemical methods

International Nuclear Information System (INIS)

Zarinskij, V.A.

1988-01-01

The use of electrochemical methods for the study of complexing, separation of rare element mixtures, their preparation in lower oxidation states, and also for the development of highly sensitive methods of the element determination, is considered in the review. Voltammetric methods of Pt, Au, Re determination are considered, as well as Re preparation in oxidation states +5, +3 by electrolytic methods. The possibility to use electrodialysis methods for purification of insoluble compounds of rare earths (RE) from impurities, and for separation of Re and Mo with simultaneous purification of Re from K and other elements is shown. The application of high-frequency conductometry to analytic chemistry and to the study of Th, In, RE complexing and kinetics of the reactions is considered

Investigation on the trace elemental profile of sewage workers in Kolkata, an Indian megacity

Directory of Open Access Journals (Sweden)

Rajlaxmi Basu

2015-07-01

Full Text Available Background. Environmental pollution has become a global health risk. Exposure to pollutants at the work place, i.e. occupational exposure, is one of the areas that need immediate attention. The civic drainage workers are exposed to pollutants present in the wastewater they handle and most of them are toxic heavy metals. Exposure to such pollutants may be a health hazard, since it can lead to the imbalance in nutrient elements status.§Design and Methods. In the present study, profiling of trace elements in the blood of drainage worker population from an Indian megacity, Kolkata, was carried out by energy dispersive x-ray fluorescence (EDXRF and compared with the control group population of the same area. Results. The elements detected by EDXRF spectrometry include P, S, Cl, K, Fe, Cu, Zn, Se, Br, and Rb. By using ANOVA with 5% significance level, we observed significant alterations in the trace elements status, iron over loading, selenium deficiency, and in Cu-Zn ratio. Gender specific variations within the same population were also observed. Conclusions. The results indicate that the drainage workers have altered elemental profile in comparison to that of control population.

Investigation of Elemental Mass Spectrometry in Pharmacology for Peptide Quantitation at Femtomolar Levels.

Directory of Open Access Journals (Sweden)

Emmanuelle Cordeau

Full Text Available In the search of new robust and environmental-friendly analytical methods able to answer quantitative issues in pharmacology, we explore liquid chromatography (LC associated with elemental mass spectrometry (ICP-MS to monitor peptides in such complex biological matrices. The novelty is to use mass spectrometry to replace radiolabelling and radioactivity measurements, which represent up-to now the gold standard to measure organic compound concentrations in life science. As a proof of concept, we choose the vasopressin (AVP/V1A receptor system for model pharmacological assays. The capacity of ICP-MS to provide highly sensitive quantitation of metallic and hetero elements, whatever the sample medium, prompted us to investigate this technique in combination with appropriate labelling of the peptide of interest. Selenium, that is scarcely present in biological media, was selected as a good compromise between ICP-MS response, covalent tagging ability using conventional sulfur chemistry and peptide detection specificity. Applying selenium monitoring by elemental mass spectrometry in pharmacology is challenging due to the very high salt content and organic material complexity of the samples that produces polyatomic aggregates and thus potentially mass interferences with selenium detection. Hyphenation with a chromatographic separation was found compulsory. Noteworthy, we aimed to develop a straightforward quantitative protocol that can be performed in any laboratory equipped with a standard macrobore LC-ICP-MS system, in order to avoid time-consuming sample treatment or special implementation of instrumental set-up, while allowing efficient suppression of all mass interferences to reach the targeted sensitivity. Significantly, a quantification limit of 57 ng Se L-1 (72 femtomoles of injected Se was achieved, the samples issued from the pharmacological assays being directly introduced into the LC-ICP-MS system. The established method was successfully

Invariant TAD Boundaries Constrain Cell-Type-Specific Looping Interactions between Promoters and Distal Elements around the CFTR Locus.

Science.gov (United States)

Smith, Emily M; Lajoie, Bryan R; Jain, Gaurav; Dekker, Job

2016-01-07

Three-dimensional genome structure plays an important role in gene regulation. Globally, chromosomes are organized into active and inactive compartments while, at the gene level, looping interactions connect promoters to regulatory elements. Topologically associating domains (TADs), typically several hundred kilobases in size, form an intermediate level of organization. Major questions include how TADs are formed and how they are related to looping interactions between genes and regulatory elements. Here we performed a focused 5C analysis of a 2.8 Mb chromosome 7 region surrounding CFTR in a panel of cell types. We find that the same TAD boundaries are present in all cell types, indicating that TADs represent a universal chromosome architecture. Furthermore, we find that these TAD boundaries are present irrespective of the expression and looping of genes located between them. In contrast, looping interactions between promoters and regulatory elements are cell-type specific and occur mostly within TADs. This is exemplified by the CFTR promoter that in different cell types interacts with distinct sets of distal cell-type-specific regulatory elements that are all located within the same TAD. Finally, we find that long-range associations between loci located in different TADs are also detected, but these display much lower interaction frequencies than looping interactions within TADs. Interestingly, interactions between TADs are also highly cell-type-specific and often involve loci clustered around TAD boundaries. These data point to key roles of invariant TAD boundaries in constraining as well as mediating cell-type-specific long-range interactions and gene regulation. Copyright © 2016 The American Society of Human Genetics. Published by Elsevier Inc. All rights reserved.

Numerical and spectral investigations of novel infinite elements

International Nuclear Information System (INIS)

Barai, P.; Harari, I.; Barbonet, P.E.

1998-01-01

Exterior problems of time-harmonic acoustics are addressed by a novel infinite element formulation, defined on a bounded computational domain. For two-dimensional configurations with circular interfaces, the infinite element results match Quell both analytical values and those obtained from. other methods like DtN. Along 1uith the numerical performance of this formulation, of considerable interest are its complex-valued eigenvalues. Hence, a spectral analysis of the present scheme is also performed here, using various infinite elements

Nitinol Embolic Protection Filters: Design Investigation by Finite Element Analysis

Science.gov (United States)

Conti, Michele; de Beule, Matthieu; Mortier, Peter; van Loo, Denis; Verdonck, Pascal; Vermassen, Frank; Segers, Patrick; Auricchio, Ferdinando; Verhegghe, Benedict

2009-08-01

The widespread acceptance of carotid artery stenting (CAS) to treat carotid artery stenosis and its effectiveness compared with surgical counterpart, carotid endarterectomy (CEA), is still a matter of debate. Transient or permanent neurological deficits may develop in patients undergoing CAS due to distal embolization or hemodynamic changes. Design, development, and usage of embolic protection devices (EPDs), such as embolic protection filters, appear to have a significant impact on the success of CAS. Unfortunately, some drawbacks, such as filtering failure, inability to cross tortuous high-grade stenoses, malpositioning and vessel injury, still remain and require design improvement. Currently, many different designs of such devices are available on the rapidly growing dedicated market. In spite of such a growing commercial interest, there is a significant need for design tools as well as for careful engineering investigations and design analyses of such nitinol devices. The present study aims to investigate the embolic protection filter design by finite element analysis. We first developed a parametrical computer-aided design model of an embolic filter based on micro-CT scans of the Angioguard™ XP (Cordis Endovascular, FL) EPD by means of the open source pyFormex software. Subsequently, we used the finite element method to simulate the deployment of the nitinol filter as it exits the delivery sheath. Comparison of the simulations with micro-CT images of the real device exiting the catheter showed excellent correspondence with our simulations. Finally, we evaluated circumferential basket-vessel wall apposition of a 4 mm size filter in a straight vessel of different sizes and shape. We conclude that the proposed methodology offers a useful tool to evaluate and to compare current or new designs of EPDs. Further simulations will investigate vessel wall apposition in a realistic tortuous anatomy.

Application of nuclear analytical techniques to investigate trace element content in foodstuffs

International Nuclear Information System (INIS)

Gharib, A.

1985-01-01

The study performed as a joint project with the IAEA includes those foodstuffs which are being used widely in Iran. It was investigated their nutritional requirements, interrelations and the role of their trace elements in metabolism. Various analytical techniques was assessed and compared. The methods involved in the study were ASS, PIXE and NAA (instrumental and radiochemical)

A report on the trace element investigations in relation to cardio-vascular diseases

International Nuclear Information System (INIS)

Cruz, B. de la; Lansangan, L.M.; Paradero, R.R.; Asprer, G.

1976-03-01

Zinc, copper and molybdenum has both beneficial and harmful effects to the health of an individual. It has been found that zinc has a protective action against hypertension, while copper maintains the elasticity of the blood vessels, and at the same time, an increase in copper can also enhance atherogenesis. In this investigation, amounts of the said trace elements have been determined in ten normal male subjects who met accidental death. The normal values obtained in these subjects were compared to the mean values of their trace elements obtained from patients who died of ischaemic heart diseases

Use of a New Method Involving Labelling with Non-Radioactive Elements and Activation Analysis to Investigate Wear

International Nuclear Information System (INIS)

Radvan, M.; Reven'ska-Kos'tsjuk, B.; Vez'ranovski, E

1967-01-01

In view of the considerable difficulties in using the labelled-atom method to investigate the wear of bearings in agricultural machines under operating conditions, and also to investigate the wear of fire-proof materials in steel production (owing to the occurrence of exogenous non-metallic inclusions), the authors turned their attention to labelling these parts with nonradioactive elements, which were then determined by activation analysis. In the work carried out by this method either mixtures of rare-earth oxides or lanthanum oxide alone were used as tracers, because of their useful nuclear properties. The use of rare-earth elements is also justified by the fact that their chemical properties differ from those of the remaining elements in the material investigated, which means that they can be separated from the respective carriers. In investigations of the wear of agricultural machine bearings made from cast-iron modified with rare-earth elements in an amount too low to cause structural changes, the authors used the modifier as a tracer. The wear of polyamide bearings was also investigated. The use of activation analysis is particularly interesting in this case, since certain properties of the polyamide make standard methods of investigation completely impossible. The products of wear were separated from the oil or grease by extraction or combustion. In determinations of non-metallic exogenous inclusions in ball-bearing steel, caused by certain fireproof materials, the wear of these materials was investigated using modem steel production technology. The aim of these investigations was to determine the effect of vacuum extraction and the use of induction mixers on the passage of fire-resistant particles into the steel. A method of determination was developed based on chemical separation of the tracer after activation with an appropriate surplus of non-radioactive carrier, and also a method of separating it before activation with a calcium carrier. The authors

An investigation of noise produced by unsteady gas flow through silencer elements

Science.gov (United States)

Mawhinney, Graeme Hugh

This thesis presents an investigation of the noise produced by unsteady gas flow through silencer elements. The central aim of the research project was to produce a tool for assistance in the design of the exhaust systems of diesel powered electrical generator sets, with the modelling techniques developed having a much wider application in reciprocating internal combustion engine exhaust systems. An automotive cylinder head was incorporated in a purpose built test rig to supply exhaust pulses, typical of those found in the exhaust system of four stroke diesel engines, to various experimental exhaust systems. Exhaust silencer elements evaluated included expansion, re- entrant, concentric tube resonator and absorptive elements. Measurements taken on the test rig included, unsteady superposition pressure in the exhaust ducting, cyclically averaged mass flow rate through the system and exhaust noise levels radiated into a semi-anechoic measurement chamber. The entire test rig was modelled using the 1D finite volume method developed previously developed at Queen's University Belfast. Various boundary conditions, developed over the years, were used to model the various silencer elements being evaluated. The 1D gas dynamic simulation thus estimated the mass flux history at the open end of the exhaust system. The mass flux history was then broken into its harmonic components and an acoustic radiation model was developed to model the sound pressure level produced by an acoustic monopole over a reflecting plane. The accuracy of the simulation technique was evaluated by correlation of measured and simulated superposition pressure and noise data. In general correlation of superposition pressure was excellent for all of the silencer elements tested. Predicted sound pressure level radiated from the open end of the exhaust tailpipe was seen to be accurate in the 100 Hz to 1 kHz frequency range for all of the silencer elements tested.

A site-specific and multi-element isotopic approach to origin inference of sugars in foods and beverages

International Nuclear Information System (INIS)

Martin, M.L.; Martin, G.J.; Guillou, C.

1991-01-01

A strategy is presented for the characterization of sugars according to their botanical origin. The samples fermented in standardized conditions can be described in the multi-dimensional space of the overall carbon isotope ratio of ethanol measured by isotope ratio mass spectrometry (IRMS) and of the specific hydrogen isotope parameters of the methyl and methylene sites derived from nuclear magnetic resonance investigation of site-specific natural isotope fractionation (SNIF-NMR method). In the comparison of natural juices, the deuterium and oxygen-18 parameters of water extracted from the juice and from the end fermentation medium also contain information on the origin of the product. The isotopic effects of the concentration processes leading to concentrated juices, musts and syrups can be estimated and taken into account in interpreting the data. The classification power of this multi-element and multi-site approach is illustrated by discriminant analyses involving selected isotopic variables associated with pineapple, apple and barley sugars, compared to beet and cane sugars which are common sources of enrichment. The ability of the method to detect adulteration by exogenous sugars is improved when environmental conditions can be taken into account. (authors)

Investigation of trace elements in Elbe water by means of instrumental neutron activation analysis

International Nuclear Information System (INIS)

Motamedi, K.

1977-01-01

Investigations of trace elements in Elbe water were carried out as a contribution to environmental research, hydrology, and geochemistry. The method applied - instrumental neutron activation analysis - is described, and problems connected with the course of analysis - sample taking, handling and preparation as well as optimization of in-pile irradiation and measurement by means of γ spectrometry - are discussed and presented one by one. The computer programme set up for automatic evaluation is described in more detail. This programme AKAN has a very general concept which makes it applicable for general use. The reliability of the evaluation procedure - monostandard method - and the reproducibility of the results are discussed. For the studies, samples were taken at different times, every time from 8 positions along a long section of the Elbe. The content of solids was analyzed; in a number of samples, this was done by separating suspended and dissolved materials. Up to 38 elements were analyzed, whose local and time-dependent concentration curves are given. The contents of some elements are compared with the few available data from literature. Correlation calculations indicate a similar behaviour of single element groups and yield information on the natural origin of the trace elements and on anthropogenic influence to be noticed in the trace element contents. (orig.) [de

Finite element speaker-specific face model generation for the study of speech production.

Science.gov (United States)

Bucki, Marek; Nazari, Mohammad Ali; Payan, Yohan

2010-08-01

In situations where automatic mesh generation is unsuitable, the finite element (FE) mesh registration technique known as mesh-match-and-repair (MMRep) is an interesting option for quickly creating a subject-specific FE model by fitting a predefined template mesh onto the target organ. The irregular or poor quality elements produced by the elastic deformation are corrected by a 'mesh reparation' procedure ensuring that the desired regularity and quality standards are met. Here, we further extend the MMRep capabilities and demonstrate the possibility of taking into account additional relevant anatomical features. We illustrate this approach with an example of biomechanical model generation of a speaker's face comprising face muscle insertions. While taking advantage of the a priori knowledge about tissues conveyed by the template model, this novel, fast and automatic mesh registration technique makes it possible to achieve greater modelling realism by accurately representing the organ surface as well as inner anatomical or functional structures of interest.

Oesophageal cancer in the Transkei: multi-elemental investigation of plant material and water

International Nuclear Information System (INIS)

Renan, M.J.; Drennan, B.D.; Keddy, R.J.; Sellschop, J.P.F.

1978-01-01

A programme which investigates possible environmental factors which may have an effect on the demographic distribution of oesophageal cancer in the Transkei has been initiated. This report deals with the collection, handling and trace elemental analysis of maize leaves, rice, tomato leaves, spinach, pine needles and orchard leaves

Fabrication technology of spherical fuel element for HTR-10

International Nuclear Information System (INIS)

He Jun; Zou Yanwen; Liang Tongxiang; Qiu Xueliang

2002-01-01

R and D on the fabrication technology of the spherical fuel elements for the 10 MW HTR Test Module (HTR-10) began from 1986. Cold quasi-isostatic molding with a silicon rubber die is used for manufacturing the spherical fuel elements.The fabrication technology and the graphite matrix materials were investigated and optimized. Twenty five batches of fuel elements, about 11000 of the fuel elements, have been produced. The cold properties of the graphite matrix materials satisfied the design specifications. The mean free uranium fraction of 25 batches was 5 x 10 -5

Nuclear Structure of the Heaviest Elements – Investigated at SHIP-GSI

Directory of Open Access Journals (Sweden)

Heßberger Fritz Peter

2014-03-01

Full Text Available The quest for the heaviest nuclei that can exist is a basic topic in natural science as their stability is characterized by a delicate interplay of short range nuclear forces acting between the nucleons (protons and neutrons and long-range Coulomb forces acting solely between charged particles, i.e. the protons. As the stability of a nucleus is strongly correlated to its structure, understanding the nuclear structure of heaviest nuclei is presently a main challenge of experimental and theoretical investigations concerning the field of Superheavy Elements. At the velocity filter SHIP at GSI Darmstadt an extensive program on nuclear structure investigations has been started about a decade ago. The project covered both as well systematic investigations of single particle levels in odd-mass isotopes populated by α-decay as investigation of two- or fourquasi-particle states forming K isomers and was supplemented by direct mass measurements at SHIPTRAP and investigation of spontaneous fission properties. Recent experimental studies allowed to extend the systematics of low lying levels in N = 151 and N = 153 up to 255Rf and 259Sg, investigation of possible relations between nuclear structure and fission properties of odd-mass nuclei and investigation of shell strengths at N = 152 and towards N = 162.

An investigation of changes in element distribution and chemical states during differentiation of embryonic stem cells

International Nuclear Information System (INIS)

Sugimoto, T.; Ide-Ektessabi, A.; Ishihara, R.; Tanigaki, M.

2004-01-01

Metallic elements and their organic compounds have dynamic regulatory functions in cells. In this study, we implemented a new approach to investigate the mechanism of differentiation of embryonic stem cells, by measuring and analyzing the change in distribution and chemical states of intracellular trace elements. We anticipate that trace metal elements and metalloproteins play important roles in the direction of differentiation, both as active centers, and as factors in the death of neural cells in neurodegenerative disorders. The aim of this study is to analyze the distribution and chemical states of trace elements during the process of differentiation of mouse embryonic stem cells, and to understand how these factors relate to the differentiation process. Using the experimental results, some previously unexplained points are considered, namely (1) how the intracellular elements change during the process of neuronal differentiation, and (2) what the optimal conditions of such elements are for neuronal differentiation. The information obtained during this study is relevant to nervous system development and evolution

An investigation of changes in element distribution and chemical states during differentiation of embryonic stem cells

Energy Technology Data Exchange (ETDEWEB)

Sugimoto, T.; Ide-Ektessabi, A. E-mail: h51167@sakura.kudpc.kyoto-u.ac.jp; Ishihara, R.; Tanigaki, M

2004-07-01

Metallic elements and their organic compounds have dynamic regulatory functions in cells. In this study, we implemented a new approach to investigate the mechanism of differentiation of embryonic stem cells, by measuring and analyzing the change in distribution and chemical states of intracellular trace elements. We anticipate that trace metal elements and metalloproteins play important roles in the direction of differentiation, both as active centers, and as factors in the death of neural cells in neurodegenerative disorders. The aim of this study is to analyze the distribution and chemical states of trace elements during the process of differentiation of mouse embryonic stem cells, and to understand how these factors relate to the differentiation process. Using the experimental results, some previously unexplained points are considered, namely (1) how the intracellular elements change during the process of neuronal differentiation, and (2) what the optimal conditions of such elements are for neuronal differentiation. The information obtained during this study is relevant to nervous system development and evolution.

Transposable elements in phytopathogenic Verticillium spp.: insights into genome evolution and inter- and intra-specific diversification

Directory of Open Access Journals (Sweden)

Amyotte Stefan G

2012-07-01

Full Text Available Abstract Background Verticillium dahliae (Vd and Verticillium albo-atrum (Va are cosmopolitan soil fungi causing very disruptive vascular diseases on a wide range of crop plants. To date, no sexual stage has been identified in either microorganism suggesting that somatic mutation is a major force in generating genetic diversity. Whole genome comparative analysis of the recently sequenced strains VdLs.17 and VaMs.102 revealed that non-random insertions of transposable elements (TEs have contributed to the generation of four lineage-specific (LS regions in VdLs.17. Results We present here a detailed analysis of Class I retrotransposons and Class II “cut-and-paste” DNA elements detected in the sequenced Verticillium genomes. We report also of their distribution in other Vd and Va isolates from various geographic origins. In VdLs.17, we identified and characterized 56 complete retrotransposons of the Gypsy-, Copia- and LINE-like types, as well as 34 full-length elements of the “cut-and-paste” superfamilies Tc1/mariner, Activator and Mutator. While Copia and Tc1/mariner were present in multiple identical copies, Activator and Mutator sequences were highly divergent. Most elements comprised complete ORFs, had matching ESTs and showed active transcription in response to stress treatment. Noticeably, we found evidences of repeat-induced point mutation (RIP only in some of the Gypsy retroelements. While Copia-, Gypsy- and Tc1/mariner-like transposons were prominent, a large variation in presence of the other types of mobile elements was detected in the other Verticillium spp. strains surveyed. In particular, neither complete nor defective “cut-and-paste” TEs were found in VaMs.102. Conclusions Copia-, Gypsy- and Tc1/mariner-like transposons are the most wide-spread TEs in the phytopathogens V. dahliae and V. albo-atrum. In VdLs.17, we identified several retroelements and “cut-and-paste” transposons still potentially active. Some of these

Ring tests on high density polyethylene: Full investigation assisted by finite element modeling

International Nuclear Information System (INIS)

Laiarinandrasana, L.; Devilliers, C.; Oberti, S.; Gaudichet, E.; Fayolle, B.; Lucatelli, J.M.

2011-01-01

In order to characterize the mechanical behavior of HDPE pipes, the ASTM D 2290-04 standard recommends carrying out tensile tests on notched rings, cut out from the pipe. This very simple test is also utilized to investigate the aging effect of the pipe by determining the strain at failure. Comparison between full ring and notched ring mechanical responses are discussed. Constitutive modeling including strain rate effects was performed by finite element analysis. This allowed a better understanding of the stress state in the cross section perpendicular to the loading direction. Additionally, the influence of a thin layer of oxidized HDPE in the inner wall of the ring was studied in the light of the finite element results.

Noncoding Elements: Evolution and Epigenetic Regulation

KAUST Repository

Seridi, Loqmane

2016-03-09

When the human genome project was completed, it revealed a surprising result. 98% of the genome did not code for protein of which more than 50% are repeats— later known as ”Junk DNA”. However, comparative genomics unveiled that many noncoding elements are evolutionarily constrained; thus luckily to have a role in genome stability and regulation. Though, their exact functions remained largely unknown. Several large international consortia such as the Functional Annotation of Mammalian Genomes (FANTOM) and the Encyclopedia of DNA Elements (ENCODE) were set to understand the structure and the regulation of the genome. Specifically, these endeavors aim to measure and reveal the transcribed components and functional elements of the genome. One of the most the striking findings of these efforts is that most of the genome is transcribed, including non-conserved noncoding elements and repeat elements. Specifically, we investigated the evolution and epigenetic properties of noncoding elements. 1. We compared genomes of evolutionarily distant species and showed the ubiquity of constrained noncoding elements in metazoa. 2. By integrating multi-omic data (such as transcriptome, nucleosome profiling, histone modifications), I conducted a comprehensive analysis of epigenetic properties (chromatin states) of conserved noncoding elements in insects. We showed that those elements have distinct and protective sequence features, undergo dynamic epigenetic regulation, and appear to be associated with the structural components of the chromatin, replication origins, and nuclear matrix. 3. I focused on the relationship between enhancers and repetitive elements. Using Cap Analysis of Gene Expression (CAGE) and RNASeq, I compiled a full catalog of active enhancers (a class of noncoding elements) during myogenesis of human primary cells of healthy donors and donors affected by Duchenne muscular dystrophy (DMD). Comparing the two time-courses, a significant change in the epigenetic

Investigation of some specific industry objects effect on plants

International Nuclear Information System (INIS)

Kadirova, M.; Mukhamedshina, N. M.; Mirsagatova, A. A.; Norboev, N.; Amanov, M.; Baynazarov, B.; Khushvaktov, T.

2001-01-01

Such industry objects as metallurgical works, chemical fertilizers manufacture, automobile industry and others are contribute to contaminate an environment. For example, it is known, that aluminum factories throw out in an environment fluorine hydride, solid fluorides, nitrogen dioxide, sulpher dioxide, hydrocarbons, ions of heavy metals and others. For comparison of harmful action of various industrial objects on plants we had investigate some leaves and seed of plants grown in areas of Tadjik aluminum factory, Chirchik works of heatproof and refractory metals, Asaka automobile works and Tashkent nuclear reactor action. Investigations were conduct by nuclear techniques and by physical and agrotechnical ethods. The alternative methods have been used by Tashkent state agrarian university. High sensitive and reliable multielement instrumental neutron activation analysis (INAA) and X-ray radiometric techniques for determination of 27 elements in plant have been developed in the Institute of nuclear physics (INP)

Stem loop sequences specific to transposable element IS605 are found linked to lipoprotein genes in Borrelia plasmids.

Directory of Open Access Journals (Sweden)

Nicholas Delihas

Full Text Available BACKGROUND: Plasmids of Borrelia species are dynamic structures that contain a large number of repetitive genes, gene fragments, and gene fusions. In addition, the transposable element IS605/200 family, as well as degenerate forms of this IS element, are prevalent. In Helicobacter pylori, flanking regions of the IS605 transposase gene contain sequences that fold into identical small stem loops. These function in transposition at the single-stranded DNA level. METHODOLOGY/PRINCIPAL FINDINGS: In work reported here, bioinformatics techniques were used to scan Borrelia plasmid genomes for IS605 transposable element specific stem loop sequences. Two variant stem loop motifs are found in the left and right flanking regions of the transposase gene. Both motifs appear to have dispersed in plasmid genomes and are found "free-standing" and phylogenetically conserved without the associated IS605 transposase gene or the adjacent flanking sequence. Importantly, IS605 specific stem loop sequences are also found at the 3' ends of lipoprotein genes (PFam12 and PFam60, however the left and right sequences appear to develop their own evolutionary patterns. The lipoprotein gene-linked left stem loop sequences maintain the IS605 stem loop motif in orthologs but only at the RNA level. These show mutations whereby variants fold into phylogenetically conserved RNA-type stem loops that contain the wobble non-Watson-Crick G-U base-pairing. The right flanking sequence is associated with the family lipoprotein-1 genes. A comparison of homologs shows that the IS605 stem loop motif rapidly dissipates, but a more elaborate secondary structure appears to develop in its place. CONCLUSIONS/SIGNIFICANCE: Stem loop sequences specific to the transposable element IS605 are present in plasmid regions devoid of a transposase gene and significantly, are found linked to lipoprotein genes in Borrelia plasmids. These sequences are evolutionarily conserved and/or structurally developed in

Predicting risk of trace element pollution from municipal roads using site-specific soil samples and remotely sensed data.

Science.gov (United States)

Reeves, Mari Kathryn; Perdue, Margaret; Munk, Lee Ann; Hagedorn, Birgit

2018-07-15

Studies of environmental processes exhibit spatial variation within data sets. The ability to derive predictions of risk from field data is a critical path forward in understanding the data and applying the information to land and resource management. Thanks to recent advances in predictive modeling, open source software, and computing, the power to do this is within grasp. This article provides an example of how we predicted relative trace element pollution risk from roads across a region by combining site specific trace element data in soils with regional land cover and planning information in a predictive model framework. In the Kenai Peninsula of Alaska, we sampled 36 sites (191 soil samples) adjacent to roads for trace elements. We then combined this site specific data with freely-available land cover and urban planning data to derive a predictive model of landscape scale environmental risk. We used six different model algorithms to analyze the dataset, comparing these in terms of their predictive abilities and the variables identified as important. Based on comparable predictive abilities (mean R 2 from 30 to 35% and mean root mean square error from 65 to 68%), we averaged all six model outputs to predict relative levels of trace element deposition in soils-given the road surface, traffic volume, sample distance from the road, land cover category, and impervious surface percentage. Mapped predictions of environmental risk from toxic trace element pollution can show land managers and transportation planners where to prioritize road renewal or maintenance by each road segment's relative environmental and human health risk. Published by Elsevier B.V.

Recent Investigations of Heavy Elements (37≤Z≤92)

International Nuclear Information System (INIS)

Biemont, E.

2011-01-01

The present paper is an update and extension of previous compilations [1, 2] and it describes recent progress regarding the investigation of the radiative properties of the elements and ions (first three ionization stages) of the fifth and sixth rows of the periodic table and of the rare earths (mostly the lanthanides). From a combination of experimental radiative lifetimes obtained with laser spectroscopy and of theoretical branching fractions calculated with a quasirelativistic Hartree-Fock approach taking configuration interaction and core-polarization effects into account, transition probabilities have been deduced for a large number of transitions of astrophysical interest. Some new results are briefly described here. The numerical values are stored in the databases DESIRE and DREAM, which are developped and progressively updated on a web site of Mons University in Belgium.

THE INFLUENCE OF CERTAIN TESTS FOR EVALUATING THE ANTROPOMETRIC, MOTOR AND SPECIFIC MOTOR DIMENSIONS ON THE ELEMENTS OF THE ATTACK IN SPORT KARATE FIGHTING

Directory of Open Access Journals (Sweden)

Žarko Kostovski

2011-08-01

Full Text Available The research involved 48 participants - top male karate competitors, juniors from karate clubs from Republic of Macedonia. The subject of this research are the defining elements of karate attack in sports karate fighting, and the basic aim is to establish the influence of anthropometric, motor and specific motor dimensions on the karate elements that use in sport karate fighting. In the research were used 36 variables: 4 antropomotorical variables, 4 variables for estimate on the explosive strength, 4 variables for estimate on the segmentary speed (movement frequency, 12 variables of the specific karate elements used in the sport karate fighting and 12 variables for estimate on the specifically karate abilities in 3 motor space: 4 variables for estimate on the specific karate coordination, 4 variables for estimate on the specific karate precision and 4 variables for estimate on the specific karate balance, which are predictive system of variables. The criterion set of variables of this research are represented by 4 karate elements which define the attack in sports karate fighting. From the received results was determined existing of groups in the different spaces of the treated variables and influence of the predictive system of variables on the criterion set of variables

Genome-Wide Comparison of Magnaporthe Species Reveals a Host-Specific Pattern of Secretory Proteins and Transposable Elements.

Directory of Open Access Journals (Sweden)

Meghana Deepak Shirke

Full Text Available Blast disease caused by the Magnaporthe species is a major factor affecting the productivity of rice, wheat and millets. This study was aimed at generating genomic information for rice and non-rice Magnaporthe isolates to understand the extent of genetic variation. We have sequenced the whole genome of the Magnaporthe isolates, infecting rice (leaf and neck, finger millet (leaf and neck, foxtail millet (leaf and buffel grass (leaf. Rice and finger millet isolates infecting both leaf and neck tissues were sequenced, since the damage and yield loss caused due to neck blast is much higher as compared to leaf blast. The genome-wide comparison was carried out to study the variability in gene content, candidate effectors, repeat element distribution, genes involved in carbohydrate metabolism and SNPs. The analysis of repeat element footprints revealed some genes such as naringenin, 2-oxoglutarate 3-dioxygenase being targeted by Pot2 and Occan, in isolates from different host species. Some repeat insertions were host-specific while other insertions were randomly shared between isolates. The distributions of repeat elements, secretory proteins, CAZymes and SNPs showed significant variation across host-specific lineages of Magnaporthe indicating an independent genome evolution orchestrated by multiple genomic factors.

Investigation of the impact of trace elements on anaerobic volatile fatty acid degradation using a fractional factorial experimental design.

Science.gov (United States)

Jiang, Ying; Zhang, Yue; Banks, Charles; Heaven, Sonia; Longhurst, Philip

2017-11-15

The requirement of trace elements (TE) in anaerobic digestion process is widely documented. However, little is understood regarding the specific requirement of elements and their critical concentrations under different operating conditions such as substrate characterisation and temperature. In this study, a flask batch trial using fractional factorial design is conducted to investigate volatile fatty acids (VFA) anaerobic degradation rate under the influence of the individual and combined effect of six TEs (Co, Ni, Mo, Se, Fe and W). The experiment inoculated with food waste digestate, spiked with sodium acetate and sodium propionate both to 10 g/l. This is followed by the addition of a selection of the six elements in accordance with a 2 6-2 fractional factorial principle. The experiment is conducted in duplicate and the degradation of VFA is regularly monitored. Factorial effect analysis on the experimental results reveals that within these experimental conditions, Se has a key role in promoting the degradation rates of both acetic and propionic acids; Mo and Co are found to have a modest effect on increasing propionic acid degradation rate. It is also revealed that Ni shows some inhibitory effects on VFA degradation, possibly due to its toxicity. Additionally, regression coefficients for the main and second order effects are calculated to establish regression models for VFA degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Stenotrophomonas maltophilia virulence and specific variations in trace elements during acute lung infection: implications in cystic fibrosis.

Directory of Open Access Journals (Sweden)

Arianna Pompilio

Full Text Available Metal ions are necessary for the proper functioning of the immune system, and, therefore, they might have a significant influence on the interaction between bacteria and host. Ionic dyshomeostasis has been recently observed also in cystic fibrosis (CF patients, whose respiratory tract is frequently colonized by Stenotrophomonas maltophilia. For the first time, here we used an inductively mass spectrometry method to perform a spatial and temporal analysis of the pattern of changes in a broad range of major trace elements in response to pulmonary infection by S. maltophilia. To this, DBA/2 mouse lungs were comparatively infected by a CF strain and by an environmental one. Our results showed that pulmonary ionomic profile was significantly affected during infection. Infected mice showed increased lung levels of Mg, P, S, K, Zn, Se, and Rb. To the contrary, Mn, Fe, Co, and Cu levels resulted significantly decreased. Changes of element concentrations were correlated with pulmonary bacterial load and markers of inflammation, and occurred mostly on day 3 post-exposure, when severity of infection culminated. Interestingly, CF strain - significantly more virulent than the environmental one in our murine model - provoked a more significant impact in perturbing pulmonary metal homeostasis. Particularly, exposure to CF strain exclusively increased P and K levels, while decreased Fe and Mn ones. Overall, our data clearly indicate that S. maltophilia modulates pulmonary metal balance in a concerted and virulence-dependent manner highlighting the potential role of the element dyshomeostasis during the progression of S. maltophilia infection, probably exacerbating the harmful effects of the loss of CF transmembrane conductance regulator function. Further investigations are required to understand the biological significance of these alterations and to confirm they are specifically caused by S. maltophilia.

Human apolipoprotein CIII gene expression is regulated by positive and negative cis-acting elements and tissue-specific protein factors

International Nuclear Information System (INIS)

Reue, K.; Leff, T.; Breslow, J.L.

1988-01-01

Apolipoprotein CIII (apoCIII) is a major protein constituent of triglyceride-rich lipoproteins and is synthesized primarily in the liver. Cis-acting DNA elements required for liver-specific apoCIII gene transcription were identified with transient expression assays in the human hepatoma (HepG2) and epithelial carcinoma (HeLa) cell lines. In liver cells, 821 nucleotides of the human apoCIII gene 5'-flanking sequence were required for maximum levels of gene expression, while the proximal 110 nucleotides alone were sufficient. No expression was observed in similar studies with HeLa cells. The level of expression was modulated by a combination of positive and negative cis-acting sequences, which interact with distinct sets of proteins from liver and HeLa cell nuclear extracts. The proximal positive regulatory region shares homology with similarly located sequences of other genes strongly expressed in the liver, including α 1 -antitrypsin and other apolipoprotein genes. The negative regulatory region is striking homologous to the human β-interferon gene regulatory element. The distal positive region shares homology with some viral enhancers and has properties of a tissue-specific enhancer. The regulation of the apoCIII gene is complex but shares features with other genes, suggesting shuffling of regulatory elements as a common mechanism for cell type-specific gene expression

Numerical Investigation of Slab-Column Connection by Finite Element Method

International Nuclear Information System (INIS)

Akram, T.; Shaikh, M.A.; Memon, A.A.

2007-01-01

The flat slab-on-column construction subjected to high transverse stresses concentrated at the slab-column connection can lead to a non-ductile, sudden and brittle punching failure and results in the accidental collapse of flat slab buildings. The major parameters affecting the slab-column connection are the concrete strength, slab thickness, slab reinforcement and aspect ratio of column. The application of numerical methods based on the finite element theory for solving practical tasks allow to perform virtual testing of structures and explore their behavior under load and other effects in different conditions taking into account the elastic and plastic behavior of materials, appearance and development of cracks and other damages (disintegrations), and finally to simulate the failure mechanism and its consequences. In this study, the models are developed to carry out the finite element analysis of slab- column connection using ADINA (Automatic Dynamic Incremental Nonlinear Analysis) by varying the slab thickness and slab confining reinforcement and to investigate their effect on the deflection and load carrying capacity. Test results indicate that by increasing the slab thickness, the deflection and the load carrying capacity of slab-column connection increases, more over, by increasing the slab confining reinforcement, the deflection decreases where as the load carrying capacity increases. (author)

New functionalities in abundant element oxides: ubiquitous element strategy

International Nuclear Information System (INIS)

Hosono, Hideo; Hayashi, Katsuro; Kamiya, Toshio; Atou, Toshiyuki; Susaki, Tomofumi

2011-01-01

While most ceramics are composed of ubiquitous elements (the ten most abundant elements within the Earth's crust), many advanced materials are based on rare elements. A 'rare-element crisis' is approaching owing to the imbalance between the limited supply of rare elements and the increasing demand. Therefore, we propose a 'ubiquitous element strategy' for materials research, which aims to apply abundant elements in a variety of innovative applications. Creation of innovative oxide materials and devices based on conventional ceramics is one specific challenge. This review describes the concept of ubiquitous element strategy and gives some highlights of our recent research on the synthesis of electronic, thermionic and structural materials using ubiquitous elements. (topical review)

Contribution of transposable elements and distal enhancers to evolution of human-specific features of interphase chromatin architecture in embryonic stem cells.

Science.gov (United States)

Glinsky, Gennadi V

2018-03-01

Transposable elements have made major evolutionary impacts on creation of primate-specific and human-specific genomic regulatory loci and species-specific genomic regulatory networks (GRNs). Molecular and genetic definitions of human-specific changes to GRNs contributing to development of unique to human phenotypes remain a highly significant challenge. Genome-wide proximity placement analysis of diverse families of human-specific genomic regulatory loci (HSGRL) identified topologically associating domains (TADs) that are significantly enriched for HSGRL and designated rapidly evolving in human TADs. Here, the analysis of HSGRL, hESC-enriched enhancers, super-enhancers (SEs), and specific sub-TAD structures termed super-enhancer domains (SEDs) has been performed. In the hESC genome, 331 of 504 (66%) of SED-harboring TADs contain HSGRL and 68% of SEDs co-localize with HSGRL, suggesting that emergence of HSGRL may have rewired SED-associated GRNs within specific TADs by inserting novel and/or erasing existing non-coding regulatory sequences. Consequently, markedly distinct features of the principal regulatory structures of interphase chromatin evolved in the hESC genome compared to mouse: the SED quantity is 3-fold higher and the median SED size is significantly larger. Concomitantly, the overall TAD quantity is increased by 42% while the median TAD size is significantly decreased (p = 9.11E-37) in the hESC genome. Present analyses illustrate a putative global role for transposable elements and HSGRL in shaping the human-specific features of the interphase chromatin organization and functions, which are facilitated by accelerated creation of novel transcription factor binding sites and new enhancers driven by targeted placement of HSGRL at defined genomic coordinates. A trend toward the convergence of TAD and SED architectures of interphase chromatin in the hESC genome may reflect changes of 3D-folding patterns of linear chromatin fibers designed to enhance both

Investigation of different types of filters for atmospheric trace elements analysis by three analytical techniques

International Nuclear Information System (INIS)

Ali, A.E.; Bacso, J.

1996-01-01

Different atmospheric aerosol samples were collected on three types of filters. Disks of both loaded and clean areas of each kind of filter were investigated by XRF, PIXE and Scanning Electron Microscope (SEM) methods. The blank concentration values of the elements Al, Si, P, S, Cl, K, Ca, Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Br and Pb in the three types of filters are discussed. It is found that for trace elemental analysis, the Nuclepore membrane filters are the most suitable for sampling. These have much lower blank element concentration values than the glass fibres and ash free filters. It was found also that the PIXE method is a more reliable analytical technique for atmospheric aerosol particles than the other methods. (author). 20 refs., 3 figs., 3 tabs

Assessing element-specific patterns of bioaccumulation across New England lakes

Energy Technology Data Exchange (ETDEWEB)

Ward, Darren M.; Mayes, Brandon; Sturup, Stefan; Folt, Carol L.; Chen, Celia Y., E-mail: celia.chen@dartmouth.edu

2012-04-01

Little is known about differences among trace elements in patterns of bioaccumulation in freshwater food webs. Our goal was to identify patterns in bioaccumulation of different elements that are large and consistent enough to discern despite variation across lakes. We measured methylmercury (MeHg) and trace element (As, Cd, Hg, Pb, and Zn) concentrations in food web components of seven New England lakes on 3-5 dates per lake, and contrasted patterns of bioaccumulation across lakes, metals and seasons. In each lake, trace element concentrations were compared across trophic levels, including three size fractions of zooplankton, planktivorous fish, and piscivorous fish. The trophic position of each food web component was estimated from N isotope analysis. Trace element concentrations varied widely among taxa, lakes and sampling dates. Yet, we identified four consistent patterns of bioaccumulation that were consistent across lakes: (1) MeHg concentration increased (i.e., was biomagnified) and Pb concentration decreased (i.e., was biodiminished) with increased trophic position. (2) Zinc concentration (as with MeHg) was higher in fish than in zooplankton, but overall variation in Zn concentration (unlike MeHg) was low. (3) Arsenic and Cd concentrations (as with Pb) were lower in fish than in zooplankton, but (unlike Pb) were not significantly correlated with trophic position within zooplankton or fish groups. (4) Average summer concentrations of As, Pb, Hg, and MeHg in zooplankton significantly predicted their concentrations in either planktivorous or piscivorous fish. Our secondary goal was to review sampling approaches in forty-five published studies to determine the extent to which current sampling programs facilitate cross-lake and cross-study comparisons of bioaccumulation. We found that studies include different components of the food web and sample too infrequently to enable strong cross-lake and cross-study comparisons. We discuss sampling strategies that would

Assessing element-specific patterns of bioaccumulation across New England lakes

International Nuclear Information System (INIS)

Ward, Darren M.; Mayes, Brandon; Sturup, Stefan; Folt, Carol L.; Chen, Celia Y.

2012-01-01

Little is known about differences among trace elements in patterns of bioaccumulation in freshwater food webs. Our goal was to identify patterns in bioaccumulation of different elements that are large and consistent enough to discern despite variation across lakes. We measured methylmercury (MeHg) and trace element (As, Cd, Hg, Pb, and Zn) concentrations in food web components of seven New England lakes on 3–5 dates per lake, and contrasted patterns of bioaccumulation across lakes, metals and seasons. In each lake, trace element concentrations were compared across trophic levels, including three size fractions of zooplankton, planktivorous fish, and piscivorous fish. The trophic position of each food web component was estimated from N isotope analysis. Trace element concentrations varied widely among taxa, lakes and sampling dates. Yet, we identified four consistent patterns of bioaccumulation that were consistent across lakes: (1) MeHg concentration increased (i.e., was biomagnified) and Pb concentration decreased (i.e., was biodiminished) with increased trophic position. (2) Zinc concentration (as with MeHg) was higher in fish than in zooplankton, but overall variation in Zn concentration (unlike MeHg) was low. (3) Arsenic and Cd concentrations (as with Pb) were lower in fish than in zooplankton, but (unlike Pb) were not significantly correlated with trophic position within zooplankton or fish groups. (4) Average summer concentrations of As, Pb, Hg, and MeHg in zooplankton significantly predicted their concentrations in either planktivorous or piscivorous fish. Our secondary goal was to review sampling approaches in forty-five published studies to determine the extent to which current sampling programs facilitate cross-lake and cross-study comparisons of bioaccumulation. We found that studies include different components of the food web and sample too infrequently to enable strong cross-lake and cross-study comparisons. We discuss sampling strategies that would

Investigation of the stability of blocks around underground openings by using the boundary element method

Directory of Open Access Journals (Sweden)

Murat Ünal

2002-03-01

Full Text Available In this study, a two-dimensional software was developed by using the boundary element method, in order to model and solve the rock mechanics problems encountered in surface and underground excavations. Stability of rock wedges formed at the roof of underground excavations were investigated in detail by using this software. The behaviour of the symmetric wedge on different joint stiffnesses was studied using a modified boundary element software. Then the results obtained were discussed and compared with the analytical solution, considering the surface tractions, shear stresses (developed along the discontinuity, wedge displacements and strains (along the wedge height.

Elemental investigation on Spanish dinosaur bones by x-ray fluorescence

International Nuclear Information System (INIS)

Brunetti, Antonio; Golosio, Bruno; Stegel, Giovanni; Piga, Giampaolo; Lasio, Barbara; Oliva, Piernicola; Enzo, Stefano

2013-01-01

In this paper we examine the chemical composition results obtained on a collection of 18 dinosaur fossil bones from Spain studied using a portable x-ray fluorescence spectrometer together with a reverse Monte Carlo numerical technique of data analysis. This approach is applied to the hypothesis of arbitrarily rough surfaces in order to account for the influence of the surface state of specimens on the chemical content evaluation. It is confirmed that the chemical content of elements is essential for understanding the changes brought about by diagenetic and taphonomic processes. However, for precise knowledge of what changes fossil bones have undergone after animal life and burial, it is necessary to use a multi-technique approach making use of other instruments like x-ray diffraction in order to describe accurately the transformations undergone by the mineralogical and bioinorganic phases and the properties of specific molecular groups. (paper)

Investigation of distribution microhomogeneity of doped elements in oxide single crystals by means of LMA-AES

International Nuclear Information System (INIS)

Nikolova, L.; Krasnobaeva, N.; Manuilov, N.

1989-01-01

The distribution of V and Ti in oxide single crystals Al 2 O 3 :V 3+ , Y 3 Al 5 O 12 :V 3+ , Al 2 O 3 :Ti 3+ , Y 3 Al 5 O 12 :Ti 3+ is investigated by laser emission microspectral analysis with photographic registration of spectra. Single crystals have been grown by the method of vertical directed crystallization (method of Bridgman-Stockbarger). For evaluation of microhomogeneity of the investigated elements distribution the following statistical methods are applied: one-way variance analysis, two-way variance analysis, regression models and gradient method. A PC programme package is developed allowing to process photoregistration data, to choose the internal standard line by scatter diagrams, to perform all statistical analysis and to plot the distribution diagrams of the elements in the samples. 2 refs. (author)

Design specification for the European Spallation Source neutron generating target element

International Nuclear Information System (INIS)

Aguilar, A.; Sordo, F.; Mora, T.; Mena, L.; Mancisidor, M.; Aguilar, J.; Bakedano, G.; Herranz, I.; Luna, P.; Magan, M.; Vivanco, R.; Jimenez-Villacorta, F.; Sjogreen, K.; Oden, U.; Perlado, J.M.

2017-01-01

The paper addresses some of the most relevant issues concerning the thermal hydraulics and radiation damage of the neutron generation target to be built at the European Spallation Source as recently approved after a critical design review. The target unit consists of a set of Tungsten blocks placed inside a wheel of 2.5 m diameter which rotates at some 0.5 Hz in order to distribute the heat generated from incoming protons which reach the target in the radial direction. The spallation material elements are composed of an array of Tungsten pieces which rest on a rotating steel support (the cassette) and are distributed in a cross-flow configuration. The thermal, mechanical and radiation effects resulting from the impact of a 2 GeV proton pulse are analysed in detail as well as an evaluation of the inventory of spallation products. The current design is found to conform to specifications and found to be robust enough to deal with several accident scenarios.

Design specification for the European Spallation Source neutron generating target element

Energy Technology Data Exchange (ETDEWEB)

Aguilar, A. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Sordo, F., E-mail: fernando.sordo@essbilbao.org [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Instituto de Fusión Nuclear, José Gutiérrez Abascal, 2, 28006 Madrid (Spain); Mora, T. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Mena, L. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Instituto de Fusión Nuclear, José Gutiérrez Abascal, 2, 28006 Madrid (Spain); Mancisidor, M.; Aguilar, J.; Bakedano, G.; Herranz, I.; Luna, P. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Magan, M.; Vivanco, R. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Instituto de Fusión Nuclear, José Gutiérrez Abascal, 2, 28006 Madrid (Spain); Jimenez-Villacorta, F. [Consorcio ESS-BILBAO. Parque Tecnológico Bizkaia. Poligono Ugaldeguren III, Pol. A, 7B, 48170 Zamudio (Spain); Sjogreen, K.; Oden, U. [European Spallation Source ERIC, P.O Box 176, SE-221 00 Lund (Sweden); Perlado, J.M. [Instituto de Fusión Nuclear, José Gutiérrez Abascal, 2, 28006 Madrid (Spain); and others

2017-06-01

The paper addresses some of the most relevant issues concerning the thermal hydraulics and radiation damage of the neutron generation target to be built at the European Spallation Source as recently approved after a critical design review. The target unit consists of a set of Tungsten blocks placed inside a wheel of 2.5 m diameter which rotates at some 0.5 Hz in order to distribute the heat generated from incoming protons which reach the target in the radial direction. The spallation material elements are composed of an array of Tungsten pieces which rest on a rotating steel support (the cassette) and are distributed in a cross-flow configuration. The thermal, mechanical and radiation effects resulting from the impact of a 2 GeV proton pulse are analysed in detail as well as an evaluation of the inventory of spallation products. The current design is found to conform to specifications and found to be robust enough to deal with several accident scenarios.

Investigating the Microscopic Location of Trace Elements in High-Alpine Glacier Ice

Science.gov (United States)

Avak, Sven Erik; Birrer, Mario; Laurent, Oscar; Guillong, Marcel; Wälle, Markus; Jenk, Theo Manuel; Bartels-Rausch, Thorsten; Schwikowski, Margit; Eichler, Anja

2017-04-01

Past changes in atmospheric pollution can be reconstructed from high-alpine ice core trace element records (Schwikowski et al., 2004). Percolation of meltwater alters the information originally stored in these environmental archives. Eichler et al. (2001) suggested that the preservation of major ions with respect to meltwater percolation depends on their location in the crystal ice lattice, i.e. grain boundaries versus grain interiors. Other studies have also focused on the effect of meltwater on organic pollutant concentrations as well as on stable isotope profiles in ice cores, whereas no information exists about trace elements. Here, we investigate for the first time the effect of the microscopic location of anthropogenic, dust and volcanic related trace elements on the behavior during meltwater percolation by using two different approaches. On the one hand we assess the microscopic location of trace elements indirectly by analyzing trace element concentrations in a high-alpine ice core, which has been shown to be affected by an inflow of meltwater, using discrete inductively coupled plasma mass spectrometry (ICP-MS). Impurities located at grain boundaries are prone to be removed by meltwater and tend to be depleted in the affected section of the record whereas those incorporated into the ice interior are preserved and not disturbed in the record. In the second approach we work towards a direct quantification of differences in concentrations of trace elements between ice grain boundaries and grain interiors in samples both from unaffected and affected sections of this ice core. Therefore we use cryocell laser ablation (LA) ICP-MS, which is the method of choice for the direct in situ chemical analysis of trace elements at a sub-millimeter resolution in glacier ice (Reinhardt et al., 2001, Della Lunga et al., 2014, Sneed et al., 2015). We will present first results of both approaches with regard to the evaluation of the potential of trace elements as environmental

Investigation of distribution of elements in a Korean ginseng by using a neutron activation method

Energy Technology Data Exchange (ETDEWEB)

Lee, Yu Na; Sun, Gwang Min; Chung, Yong Sam; Kim, Young Jin [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2009-10-15

The Distinction of production areas of Korean ginsengs has been tried by using neutron activation techniques such as an instrumental neutron activation analysis (INAA) and a prompt gamma activation analysis (PGAA). This study was done as a part of those efforts. As is well known, the distribution of elements varies according to the part of plant due to the difference of enrichment effect and influence from a soil where the plants have been grown. So a correlation study between plants and soil is an important issue. In this study, the distribution of trace elements within a Korean ginseng was investigated by using an instrumental neutron activation analysis.

Investigation on trace elements in crude oil and organic matter extracted from rocks with instrumental neutron activation analysis

International Nuclear Information System (INIS)

Ding Zuguo; Chai Zhifang

1990-01-01

Solvent extraction, column chromatography and instrumental neutron activation analysis(INAA) have been used to investigate the trace elements in crude oil, organic matter extracted from rocks and their related fractions. With these methods, about 70 crude oil samples from eight different oil fields in China and 6 extracted asphaltene samples of the lower paleozoic from the upper Yangtze region have been analyzed, and about 40 elements of interest have been determined. Those elements include Al, As, Au, Ba, Br, Cl, Co, Cr, Cs, Cu, Fe, Hf, I, Ir, Mg, Mn, Mo, Na, Ni, Rb, Re, S, Sb, Sc, Se, Sr, Th, Zn, V and parts of REE. The experimental results show that the method possesses several advantages, i.e. non-destructive, multi-elements, sensitive, precise and accurate. Without ashing samples, the loss of volatile elements such as Cl, S, Se and Sb are avoided. The column chromatography makes it possible to study the distributions of trace elements in different fractions of crude oil and organic matter extracted. Meanwhile, the characters of trace elements in them have also been discussed

An investigation of trace and radioactive elements in Elgash area

International Nuclear Information System (INIS)

Abdel Rahman, Babikir Ali

1997-08-01

In this study an evaluation of nutrients and other trace elements content in soil, plants and water samples in addition to radionuclides levels were conducted in Elgash area-eastern Sudan. An area which is located between latitude 15.3-16.5 degree and longitude 36-37degree. Investigated area during the winter season january 1995 extends from (Al-lafa) to (Wager) at the flood season september-october 1996. Analyses were carried out using atomic absorption spectrophotometry for soil and plant samples collectedd during winter season, in addition to the water, and x-ray fluorescence for soil and plant samples collected in both seasons. During the flood season, it is foundd that no considerable difference of elemental content in soil and correspondingly in the same types of plants. Macronutrients (potassium, calcium and iron) contents in soil samples during the flood season were found to range from 2.50% to 5.42%. While micronutrients (zinc, copper and cobalt) contents ranged between 40 and 206 ppm. For different plant types, macronutrients concentration such as (potassium and calcium) ranged from 0.18 to 5.11%, where as micronutrients and other minor elements (iron, zinc, copper, bromine and strontium) ranged between 04 and 2742 ppm. Average values of potassium and calcium for most samples of soil and plant were differed within the seasons, in soil the average concentration of potassium during the winter and flood season was found to be 1.53 and 3.47%, and calcium was 1.58 and 2.98% where as in plant samples the average concentration of the elements during the winter season was 1.46, 0.97% and 2.76, 1.11% during the flood season, respectively. The results of the study showed that no markedd differences in the concentrations of individual elements, in water samples due to the seasonal and geographical variations, with exception to iron which is altered in the flood season from 2.5 ppm to 13 ppm, with 400% relative to the winter season. Results also showed that water of

An investigation of trace and radioactive elements in Elgash area

Energy Technology Data Exchange (ETDEWEB)

Abdel Rahman, Babikir Ali [Department of Chemistry, Faculty of Science, University of Khartoum, Khartoum (Sudan)

1997-08-01

In this study an evaluation of nutrients and other trace elements content in soil, plants and water samples in addition to radionuclides levels were conducted in Elgash area-eastern Sudan. An area which is located between latitude 15.3-16.5 degree and longitude 36-37degree. Investigated area during the winter season january 1995 extends from (Al-lafa) to (Wager) at the flood season september-october 1996. Analyses were carried out using atomic absorption spectrophotometry for soil and plant samples collectedd during winter season, in addition to the water, and x-ray fluorescence for soil and plant samples collected in both seasons. During the flood season, it is foundd that no considerable difference of elemental content in soil and correspondingly in the same types of plants. Macronutrients (potassium, calcium and iron) contents in soil samples during the flood season were found to range from 2.50% to 5.42%. While micronutrients (zinc, copper and cobalt) contents ranged between 40 and 206 ppm. For different plant types, macronutrients concentration such as (potassium and calcium) ranged from 0.18 to 5.11%, where as micronutrients and other minor elements (iron, zinc, copper, bromine and strontium) ranged between 04 and 2742 ppm. Average values of potassium and calcium for most samples of soil and plant were differed within the seasons, in soil the average concentration of potassium during the winter and flood season was found to be 1.53 and 3.47%, and calcium was 1.58 and 2.98% where as in plant samples the average concentration of the elements during the winter season was 1.46, 0.97% and 2.76, 1.11% during the flood season, respectively. The results of the study showed that no markedd differences in the concentrations of individual elements, in water samples due to the seasonal and geographical variations, with exception to iron which is altered in the flood season from 2.5 ppm to 13 ppm, with 400% relative to the winter season. Results also showed that water of

Investigation of elements contamination and analysis of electrical effect of this contamination in silicon on the neutron transmutation doping in the RSG-GAS

International Nuclear Information System (INIS)

Sudjadi, U.

1998-01-01

The elements of the contamination on the Neutron Transmutation Doping Process (NTD) have investigated by Multi Channel Analyser (MCA). This Investigation is important to know the quality of silicon doping in NTD. We have found that Mn-45, Ga-72 and Au-198 are elements of contamination in silicon after NTD process. Analysis of electrical effect of this elements contamination on semiconductor silicon is described also in this paper

The investigation of ferromagnetic resonance linewidth in Ni80Fe20 films with submicron rectangular elements

Directory of Open Access Journals (Sweden)

D. Zhang

2016-05-01

Full Text Available Patterned magnetic films with nano-scaled dots exhibit some special magnetic properties. In this paper, we investigate the in-plane shape anisotropy and the magnetization dynamic damping in permalloy (Ni80Fe20 arrays of submicron rectangular elements using ferromagnetic resonance (FMR. The FMR linewidth exhibits a dependence on the element size, and mainly comes from the contribution of the intrinsic damping. Also the contribution of two-magnon scattering plays an important role and is reduced with increasing aspect ratio. The damping coefficient decreases from 0.0129 to 0.0118 with the element length increasing from 300 nm to 1200 nm, and the theoretical calculation suggests that the change of damping results from the longitudinal and transverse interlayer spin current due to the spatially inhomogeneous magnetization dynamics.

Mendeleev's principle against Einstein's relativity: news from the chemistry of superheavy elements

Energy Technology Data Exchange (ETDEWEB)

Gaeggeler, Heinz W [Department of Chemistry and Biochemistry, University of Bern, Bern (Switzerland)

2009-12-31

The review briefly considers the problems of synthesis and chemical identification of superheavy elements. The specific features of their properties are determined by the relativistic effects. The synthesis and chemical investigations into bohrium and element 112 are discussed as examples.

Investigation of the influence of vertical force on the contact between truck tyre and road using finite element analyses

Science.gov (United States)

Moisescu, Alexandra-Raluca; Anghelache, Gabriel

2017-10-01

In the modern context of automobile integration with the emerging technologies of the interconnected society, the interaction between tyre and road is an element of major importance for automobile safety systems such as the intelligent tyres, as well as for passenger comfort, fuel economy, environmental protection, infrastructure and vehicle durability. The tyre-road contact generates the distribution of forces exerted on each unit area in the contact patch, therefore the distribution of contact stresses on three orthogonal directions. The numerical investigation of stresses distribution in the contact patch requires the development of finite element models capable of accurately describing the interaction between tyre and rolling surface. The complex finite element model developed for the 11R22.5 truck tyre has been used for investigating the influence of vertical force on the distributions of contact stresses. In addition to these contributions, the paper presents aspects related to the simulation of truck tyre radial stiffness. The influence of tyre rolling has not been taken into consideration, as the purpose of the current research is the investigation of tyre-road contact in stationary conditions.

Integrative modeling of eQTLs and cis-regulatory elements suggests mechanisms underlying cell type specificity of eQTLs.

Directory of Open Access Journals (Sweden)

Christopher D Brown

Full Text Available Genetic variants in cis-regulatory elements or trans-acting regulators frequently influence the quantity and spatiotemporal distribution of gene transcription. Recent interest in expression quantitative trait locus (eQTL mapping has paralleled the adoption of genome-wide association studies (GWAS for the analysis of complex traits and disease in humans. Under the hypothesis that many GWAS associations tag non-coding SNPs with small effects, and that these SNPs exert phenotypic control by modifying gene expression, it has become common to interpret GWAS associations using eQTL data. To fully exploit the mechanistic interpretability of eQTL-GWAS comparisons, an improved understanding of the genetic architecture and causal mechanisms of cell type specificity of eQTLs is required. We address this need by performing an eQTL analysis in three parts: first we identified eQTLs from eleven studies on seven cell types; then we integrated eQTL data with cis-regulatory element (CRE data from the ENCODE project; finally we built a set of classifiers to predict the cell type specificity of eQTLs. The cell type specificity of eQTLs is associated with eQTL SNP overlap with hundreds of cell type specific CRE classes, including enhancer, promoter, and repressive chromatin marks, regions of open chromatin, and many classes of DNA binding proteins. These associations provide insight into the molecular mechanisms generating the cell type specificity of eQTLs and the mode of regulation of corresponding eQTLs. Using a random forest classifier with cell specific CRE-SNP overlap as features, we demonstrate the feasibility of predicting the cell type specificity of eQTLs. We then demonstrate that CREs from a trait-associated cell type can be used to annotate GWAS associations in the absence of eQTL data for that cell type. We anticipate that such integrative, predictive modeling of cell specificity will improve our ability to understand the mechanistic basis of human

Investigation on trace and major elements in anti-asthmatic medicinal plants by PIXE and PIGE techniques

Science.gov (United States)

Bhanisana Devi, R. K.; Nandakumar Sarma, H.; Kumar, Sanjiv

2015-01-01

Five widely used anti-asthmatic medicinal plants of north-eastern region of India have been investigated by using Proton Induced X-ray Emission (PIXE) and Proton Induced Gamma ray Emission (PIGE) techniques. The elements namely K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se and Br were detected with different concentrations (in ppm level) by PIXE technique whereas light elements namely F, Na, Mg, Al, P and Cl by PIGE technique in the studied plants. No toxic heavy metals such as Hg, Pb, Cd were detected. Analysis was performed on thick targets (pellets) prepared using the powders of specimens through a series of processing steps. Thick targets of plant based Certified Reference Materials (CRMs) were served as standardization of PIXE and PIGE set up. The trace elements present in the studied plants have been correlated with their medicinal properties.

Investigation on trace and major elements in anti-asthmatic medicinal plants by PIXE and PIGE techniques

Energy Technology Data Exchange (ETDEWEB)

Bhanisana Devi, R.K., E-mail: bhanisanark@gmail.com [Department of Physics, Manipur University, Canchipur 795003 (India); Nandakumar Sarma, H. [Department of Physics, Manipur University, Canchipur 795003 (India); Kumar, Sanjiv [National Centre for Compositional Characterization of Materials (NCCCM), Hyderabad 500062 (India)

2015-01-15

Five widely used anti-asthmatic medicinal plants of north-eastern region of India have been investigated by using Proton Induced X-ray Emission (PIXE) and Proton Induced Gamma ray Emission (PIGE) techniques. The elements namely K, Ca, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se and Br were detected with different concentrations (in ppm level) by PIXE technique whereas light elements namely F, Na, Mg, Al, P and Cl by PIGE technique in the studied plants. No toxic heavy metals such as Hg, Pb, Cd were detected. Analysis was performed on thick targets (pellets) prepared using the powders of specimens through a series of processing steps. Thick targets of plant based Certified Reference Materials (CRMs) were served as standardization of PIXE and PIGE set up. The trace elements present in the studied plants have been correlated with their medicinal properties.

A discrete element model for the investigation of the geometrically nonlinear behaviour of solids

Science.gov (United States)

Ockelmann, Felix; Dinkler, Dieter

2018-07-01

A three-dimensional discrete element model for elastic solids with large deformations is presented. Therefore, an discontinuum approach is made for solids. The properties of elastic material are transferred analytically into the parameters of a discrete element model. A new and improved octahedron gap-filled face-centred cubic close packing of spheres is split into unit cells, to determine the parameters of the discrete element model. The symmetrical unit cells allow a model with equal shear components in each contact plane and fully isotropic behaviour for Poisson's ratio above 0. To validate and show the broad field of applications of the new model, the pin-pin Euler elastica is presented and investigated. The thin and sensitive structure tends to undergo large deformations and rotations with a highly geometrically nonlinear behaviour. This behaviour of the elastica can be modelled and is compared to reference solutions. Afterwards, an improved more realistic simulation of the elastica is presented which softens secondary buckling phenomena. The model is capable of simulating solids with small strains but large deformations and a strongly geometrically nonlinear behaviour, taking the shear stiffness of the material into account correctly.

Investigation of Apple Vibration Characteristics Using Finite Element Modal Analysis

Directory of Open Access Journals (Sweden)

R Mirzaei

2013-02-01

Full Text Available The most important quality indicator of fruits is the flesh firmness which is well correlated to their young’s modulus. In this research variation of vibration characteristics (shape modes, natural frequency of apple due to change of material characteristics (density, young's models, Poisson ratio and apple volume was investigated using Finite Element simulation. An image processing technique was used to obtain an unsymmetrical and non-spherical geometric model of apple. The exact three-dimensional shape of the fruit was created by determining the coordinates of apple surface and forming uneven rotational curvatures. Modal analysis with no boundary constraints has been applied. The first 20 Eigen frequencies and the corresponding mode shape were determined. Six rigid body modes possess zero resonant frequency which is related to the degree of freedom of a rigid body in space indicated the validity of finite element model. The modal analysis results showed that resonant frequency increased by increasing young's modulus of the fruit, while it decreased by increasing apple density. First mode torsion has a mean resonant frequency of 584 Hz. Variations of natural frequency due to change in young's modulus, density, and Poisson ratio were 80%, 11% and 4%, respectively. Coefficient of variation of resonant frequency in response to changing young's modulus was 2-3 times of that of density which shows the greatest effect of young modulus changes on natural frequency of fruits. Consequently with determination of fruits' natural frequency, their young modulus and firmness can be estimated.

An Investigation of Trace Elements in Marine and Lacustrine Deposits by Means of a Neutron Activation Method

Energy Technology Data Exchange (ETDEWEB)

Landstroem, O; Samsahl, K; Wenner, C G

1967-10-15

A neutron activation method for multi-elemental analysis was applied to argillaceous deposits from the Viskan Valley on the Swedish West Coast, an area in which transgressions and regressions of the sea have occurred during the postglacial time. These changes between fresh-water and marine stages are well known from earlier geologic investigations. Analysis could therefore be performed of samples of known marine (brackish) and lacustrine origin. In a preliminary test on four samples, taken from two marine layers and two lacustrine layers, altogether 30 elements were quantitatively determined, namely As, Br, Ca, Ce, Co, Cr, Cs, Eu, Fe, Ga, Hf, Hg, La, Lu, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, W, Yb, Zn and Zr. Several elements showed a difference in concentration between the marine and the fresh-water layers. Br, Hg, Mn, Se, As and Sb were more thoroughly investigated in three boreholes from different sections of the valley. Br and Se had high means in the most pronounced marine samples of the fiord deposits. Moreover, Mn showed a fourfold increase just in the transition stage between the older sea fiord and the older lage stage.

An Investigation of Trace Elements in Marine and Lacustrine Deposits by Means of a Neutron Activation Method

International Nuclear Information System (INIS)

Landstroem, O.; Samsahl, K.; Wenner, C.G.

1967-10-01

A neutron activation method for multi-elemental analysis was applied to argillaceous deposits from the Viskan Valley on the Swedish West Coast, an area in which transgressions and regressions of the sea have occurred during the postglacial time. These changes between fresh-water and marine stages are well known from earlier geologic investigations. Analysis could therefore be performed of samples of known marine (brackish) and lacustrine origin. In a preliminary test on four samples, taken from two marine layers and two lacustrine layers, altogether 30 elements were quantitatively determined, namely As, Br, Ca, Ce, Co, Cr, Cs, Eu, Fe, Ga, Hf, Hg, La, Lu, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, W, Yb, Zn and Zr. Several elements showed a difference in concentration between the marine and the fresh-water layers. Br, Hg, Mn, Se, As and Sb were more thoroughly investigated in three boreholes from different sections of the valley. Br and Se had high means in the most pronounced marine samples of the fiord deposits. Moreover, Mn showed a fourfold increase just in the transition stage between the older sea fiord and the older lage stage

The Specificity of Innate Immune Responses Is Enforced by Repression of Interferon Response Elements by NF-κB p50

Science.gov (United States)

Cheng, Christine S.; Feldman, Kristyn E.; Lee, James; Verma, Shilpi; Huang, De-Bin; Huynh, Kim; Chang, Mikyoung; Ponomarenko, Julia V.; Sun, Shao-Cong; Benedict, Chris A.; Ghosh, Gourisankar; Hoffmann, Alexander

2011-01-01

The specific binding of transcription factors to cognate sequence elements is thought to be critical for the generation of specific gene expression programs. Members of the nuclear factor κB (NF-κB) and interferon (IFN) regulatory factor (IRF) transcription factor families bind to the κB site and the IFN response element (IRE), respectively, of target genes, and they are activated in macrophages after exposure to pathogens. However, how these factors produce pathogen-specific inflammatory and immune responses remains poorly understood. Combining top-down and bottom-up systems biology approaches, we have identified the NF-κB p50 homodimer as a regulator of IRF responses. Unbiased genome-wide expression and biochemical and structural analyses revealed that the p50 homodimer repressed a subset of IFN-inducible genes through a previously uncharacterized subclass of guanine-rich IRE (G-IRE) sequences. Mathematical modeling predicted that the p50 homodimer might enforce the stimulus specificity of composite promoters. Indeed, the production of the antiviral regulator IFN-β was rendered stimulus-specific by the binding of the p50 homodimer to the G-IRE–containing IFNβ enhancer to suppress cytotoxic IFN signaling. Specifically, a deficiency in p50 resulted in the inappropriate production of IFN-β in response to bacterial DNA sensed by Toll-like receptor 9. This role for the NF-κB p50 homodimer in enforcing the specificity of the cellular response to pathogens by binding to a subset of IRE sequences alters our understanding of how the NF-κB and IRF signaling systems cooperate to regulate antimicrobial immunity. PMID:21343618

Discrete Element Modeling

Energy Technology Data Exchange (ETDEWEB)

Morris, J; Johnson, S

2007-12-03

The Distinct Element Method (also frequently referred to as the Discrete Element Method) (DEM) is a Lagrangian numerical technique where the computational domain consists of discrete solid elements which interact via compliant contacts. This can be contrasted with Finite Element Methods where the computational domain is assumed to represent a continuum (although many modern implementations of the FEM can accommodate some Distinct Element capabilities). Often the terms Discrete Element Method and Distinct Element Method are used interchangeably in the literature, although Cundall and Hart (1992) suggested that Discrete Element Methods should be a more inclusive term covering Distinct Element Methods, Displacement Discontinuity Analysis and Modal Methods. In this work, DEM specifically refers to the Distinct Element Method, where the discrete elements interact via compliant contacts, in contrast with Displacement Discontinuity Analysis where the contacts are rigid and all compliance is taken up by the adjacent intact material.

The calculation - experimental investigations of the HTGR fuel element construction

International Nuclear Information System (INIS)

Eremeev, V.S.; Kolesov, V.S.; Chernikov, A.S.

1985-01-01

One of the most important problems in the HTGR development is the creation of the fuel element gas-tight for the fission products. This problem is being solved by using fuel elements of dispersion type representing an ensemble of coated fuel particles dispersed in the graphite matrix. Gas-tightness of such fuel elements is reached at the expense of deposing a protective coating on the fuel particles. It is composed of some layers serving as diffusion barriers for fission products. It is apparent that the rate of fission products diffusion from coated fuel particles is determined by the strength and temperature of the protective coating

Patient-specific non-linear finite element modelling for predicting soft organ deformation in real-time: application to non-rigid neuroimage registration.

Science.gov (United States)

Wittek, Adam; Joldes, Grand; Couton, Mathieu; Warfield, Simon K; Miller, Karol

2010-12-01

Long computation times of non-linear (i.e. accounting for geometric and material non-linearity) biomechanical models have been regarded as one of the key factors preventing application of such models in predicting organ deformation for image-guided surgery. This contribution presents real-time patient-specific computation of the deformation field within the brain for six cases of brain shift induced by craniotomy (i.e. surgical opening of the skull) using specialised non-linear finite element procedures implemented on a graphics processing unit (GPU). In contrast to commercial finite element codes that rely on an updated Lagrangian formulation and implicit integration in time domain for steady state solutions, our procedures utilise the total Lagrangian formulation with explicit time stepping and dynamic relaxation. We used patient-specific finite element meshes consisting of hexahedral and non-locking tetrahedral elements, together with realistic material properties for the brain tissue and appropriate contact conditions at the boundaries. The loading was defined by prescribing deformations on the brain surface under the craniotomy. Application of the computed deformation fields to register (i.e. align) the preoperative and intraoperative images indicated that the models very accurately predict the intraoperative deformations within the brain. For each case, computing the brain deformation field took less than 4 s using an NVIDIA Tesla C870 GPU, which is two orders of magnitude reduction in computation time in comparison to our previous study in which the brain deformation was predicted using a commercial finite element solver executed on a personal computer. Copyright © 2010 Elsevier Ltd. All rights reserved.

Asynchronous Communication: Investigating the Influences of Relational Elements and Background on the Framing Structure of Emails

Science.gov (United States)

AlAfnan, Mohammad Awad

2015-01-01

This study explored the influences of relational elements and the background of communicators on the framing structure of email messages that were exchanged in an educational Institute in Malaysia. The investigation revealed that social distance played a more significant role than power relations as Malaysian respondents are, generally, more…

Human-specific subcellular compartmentalization of P-element induced wimpy testis-like (PIWIL) granules during germ cell development and spermatogenesis

NARCIS (Netherlands)

Gomes Fernandes, Maria; He, Nannan; Wang, Fang; Van Iperen, Liesbeth; Eguizabal, Cristina; Matorras, Roberto; Roelen, Bernard A J; Chuva de Sousa Lopes, Susana M

2018-01-01

STUDY QUESTION: What is the dynamics of expression of P-element induced wimpy testis-like (PIWIL) proteins in the germline during human fetal development and spermatogenesis? SUMMARY ANSWER: PIWIL1, PIWIL2, PIWIL3 and PIWIL4 were expressed in a sex-specific fashion in human germ cells (GC) during

Integrating Environmentally Responsive Elements in Buildings

DEFF Research Database (Denmark)

Heiselberg, Per

2006-01-01

Significant improvement have been achieved on efficiency improvements of specific building elements like the building envelope and building equipment and services and whilst most building elements still offer opportunities for efficiency improvements, the greatest future potential lie with techno......Significant improvement have been achieved on efficiency improvements of specific building elements like the building envelope and building equipment and services and whilst most building elements still offer opportunities for efficiency improvements, the greatest future potential lie...

Theoretical and experimental investigation of the nonlinear structural dynamics of Fast Breeder Reactor fuel elements

International Nuclear Information System (INIS)

Liebe, R.

1978-04-01

This study describes theoretical and experimental investigations of the dynamic deformation behavior of single and clustered fuel elements under local fault conditions in a Fast Breeder Reactor core. In particular an energetic molten-fuel-coolant-interaction (FCI) is assumed in one subassembly with corresponding pressure pulses, which may rupture the wrapper and load the adjacent fuel elements impulsively. Associated coherent structural deformation may exceed tolerable and damage the control rods. To attack the outlined coupled fluid-structure-interaction problem it is assumed, that the loading at the structures is known in space and time, and that there is no feedback from the deformation response. Then current FCI-knowledge and experience from underwater core model explosion tests is utilized to estimate upper limits of relevant pulse characteristics. As a first step the static carrying capacity of the rigid-plastic hexagonal wrapper tube is calculated using the methods of limit analysis. Then for a general dynamic simulation of the complete elastoplastic subassembly response the concept of a discrete nonlinear hinge is introduced. A corresponding physical lumped parameter hinge model is presented, and general equations of motion are derived using D'Alembert's principle. Application to the static and dynamic analysis of a single complete fuel element includes the semiempirical modelling of the fuel-pin bundle by a homogeneous compressible medium. Most important conclusions are concerning the capability of the theoretical models, the failure modes and threshold load levels of single as well as clustered SNR-300 fuel elements and the safety relevant finding, that only limited deformations are found in the first row around the incident element. This shows in agreement with explosion test results that the structured and closely spaced fuel elements constitute an effective, inherent barrier against extreme dynamic loadings. (orig.) [de

Fluidic Elements based on Coanda Effect

Directory of Open Access Journals (Sweden)

Constantin OLIVOTTO

2010-12-01

Full Text Available This paper contains first some definitions and classifications regarding the fluidic elements. Thegeneral current status is presented, nominating the main specific elements based on the Coanda effect developedspecially in Romania. In particularly the development of an original bistable element using industrial compressedair at industrial pressure supply is presented. The function of this element is based on the controlled attachmentof the main jet at a curved wall through the Coanda effect. The methods used for particular calculation andexperiments are nominated. The main application of these elements was to develop a specific execution element:a fluidic step–by-step motor based on the Coanda effect.

Radiolabelled cellular blood elements

International Nuclear Information System (INIS)

Sinzinger, H.

1990-01-01

This book reports on radiolabelled cellular blood elements, covering new advances made during the past several years, in particular the use of Tc-99 as a tracer for blood elements. Coverage extends to several radiolabelled monoclonal antibodies that are specific for blood components and may label blood elements in vivo

Ultrafast vortex core dynamics investigated by finite-element micromagnetic simulations

Energy Technology Data Exchange (ETDEWEB)

Gliga, Sebastian

2010-07-01

The investigations carried out in this thesis concern the ultrafast dynamics of a fundamental micromagnetic configuration: the vortex. Over the past decade, a detailed understanding of the dynamic and static properties of such magnetic nanostructures has been achieved as a result of close interplay between experiments, theory and numeric simulations. Here, micromagnetic simulations were performed based on the finite-element method. The vortex structure arises in laterally-confined ferromagnets, in particular in thin-film elements, and is characterized by an in-plane curling of the magnetic moments around a very stable and narrow core. In the present study, a novel process in micromagnetism was found: the ultrafast reversal of the vortex core. The possibility of easily switching the core orientation by means of short in-plane field pulses is surprising in view of the very high stability of the core. Moreover, the simulations presented here showed that this reversal process unfolds on a time scale of only a few tens of picoseconds, which leads to the prediction of the fastest and most complex micromagnetic reversal process known to date. Indeed, the vortex core is not merely switched: it is destroyed and recreated in the immediate vicinity with an opposite direction. This is mediated by a rapid sequence of vortex-antivortex pair creation and annihilation subprocesses and results in a sudden burst-like emission of spin waves. Equally fascinating is the ultrafast dynamics of an isolated magnetic antivortex, the topological counterpart of the vortex. The simulations performed here showed that the static complementarity between vortices and antivortices is equally reflected in their ultrafast dynamics, which leads to the reversal of the antivortex core. A promising means for the control of the magnetization on the nanoscale consists in exploiting the spin-transfer torque effect. The study of the current-induced dynamics of vortices showed that the core reversal can be

Two-point method uncertainty during control and measurement of cylindrical element diameters

Science.gov (United States)

Glukhov, V. I.; Shalay, V. V.; Radev, H.

2018-04-01

The topic of the article is devoted to the urgent problem of the reliability of technical products geometric specifications measurements. The purpose of the article is to improve the quality of parts linear sizes control by the two-point measurement method. The article task is to investigate methodical extended uncertainties in measuring cylindrical element linear sizes. The investigation method is a geometric modeling of the element surfaces shape and location deviations in a rectangular coordinate system. The studies were carried out for elements of various service use, taking into account their informativeness, corresponding to the kinematic pairs classes in theoretical mechanics and the number of constrained degrees of freedom in the datum element function. Cylindrical elements with informativity of 4, 2, 1 and θ (zero) were investigated. The uncertainties estimation of in two-point measurements was made by comparing the results of of linear dimensions measurements with the functional diameters maximum and minimum of the element material. Methodical uncertainty is formed when cylindrical elements with maximum informativeness have shape deviations of the cut and the curvature types. Methodical uncertainty is formed by measuring the element average size for all types of shape deviations. The two-point measurement method cannot take into account the location deviations of a dimensional element, so its use for elements with informativeness less than the maximum creates unacceptable methodical uncertainties in measurements of the maximum, minimum and medium linear dimensions. Similar methodical uncertainties also exist in the arbitration control of the linear dimensions of the cylindrical elements by limiting two-point gauges.

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the sediment transport modeling task

International Nuclear Information System (INIS)

Holt, V.L.; Baron, L.A.

1994-05-01

This site-specific Work Plan/Health and Safety Checklist (WP/HSC) is a supplement to the general health and safety plan (HASP) for Waste Area Grouping (WAG) 2 remedial investigation and site investigation (WAG 2 RI ampersand SI) activities [Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169)] and provides specific details and requirements for the WAG 2 RI ampersand SI Sediment Transport Modeling Task. This WP/HSC identifies specific site operations, site hazards, and any recommendations by Oak Ridge National Laboratory (ORNL) health and safety organizations [i.e., Industrial Hygiene (IH), Health Physics (HP), and/or Industrial Safety] that would contribute to the safe completion of the WAG 2 RI ampersand SI. Together, the general HASP for the WAG 2 RI ampersand SI (ORNL/ER-169) and the completed site-specific WP/HSC meet the health and safety planning requirements specified by 29 CFR 1910.120 and the ORNL Hazardous Waste Operations and Emergency Response (HAZWOPER) Program Manual. In addition to the health and safety information provided in the general HASP for the WAG 2 RI ampersand SI, details concerning the site-specific task are elaborated in this site-specific WP/HSC, and both documents, as well as all pertinent procedures referenced therein, will be reviewed by all field personnel prior to beginning operations

Investigation of Product Performance of Al-Metal Matrix Composites Brake Disc using Finite Element Analysis

International Nuclear Information System (INIS)

Fatchurrohman, N; Marini, C D; Suraya, S; Iqbal, AKM Asif

2016-01-01

The increasing demand of fuel efficiency and light weight components in automobile sectors have led to the development of advanced material parts with improved performance. A specific class of MMCs which has gained a lot of attention due to its potential is aluminium metal matrix composites (Al-MMCs). Product performance investigation of Al- MMCs is presented in this article, where an Al-MMCs brake disc is analyzed using finite element analysis. The objective is to identify the potentiality of replacing the conventional iron brake disc with Al-MMCs brake disc. The simulation results suggested that the MMCs brake disc provided better thermal and mechanical performance as compared to the conventional cast iron brake disc. Although, the Al-MMCs brake disc dissipated higher maximum temperature compared to cast iron brake disc's maximum temperature. The Al-MMCs brake disc showed a well distributed temperature than the cast iron brake disc. The high temperature developed at the ring of the disc and heat was dissipated in circumferential direction. Moreover, better thermal dissipation and conduction at brake disc rotor surface played a major influence on the stress. As a comparison, the maximum stress and strain of Al-MMCs brake disc was lower than that induced on the cast iron brake disc. (paper)

Impact of specific fracture energy investigated in front of the crack tip of three-point bending specimen

Czech Academy of Sciences Publication Activity Database

Klon, J.; Sobek, J.; Malíková, L.; Seitl, Stanislav

2017-01-01

Roč. 11, č. 41 (2017), s. 183-190 ISSN 1971-8993 Institutional support: RVO:68081723 Keywords : Finite element method * Loading curve * Specific fracture energy * Three-point bending test * Work of fracture Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering, reliability analysis

Two ABREs, two redundant root-specific and one W-box cis-acting elements are functional in the sunflower HAHB4 promoter.

Science.gov (United States)

Manavella, Pablo A; Dezar, Carlos A; Ariel, Federico D; Chan, Raquel L

2008-10-01

HAHB4 is a sunflower gene encoding a homeodomain-leucine zipper (HD-Zip) transcription factor. It was previously demonstrated that this gene is regulated at the transcriptional level by several abiotic factors and hormones. A previous analysis in the PLACE database revealed the presence of four putative ABREs. In this work these four elements and also one W-box and two root-specific expression elements were characterized as functional. Site-directed mutagenesis on the promoter, stable transformation of Arabidopis plants as well as transient transformation of sunflower leaves, were performed. The analysis of the transformants was carried out by histochemistry and real time RT-PCR. The results indicate that just one ABRE out of the four is responsible for ABA, NaCl and drought regulation. However, NaCl induction occurs also by an additional ABA-independent way involving another two overlapped ABREs. On the other hand, it was determined that the W-box located 5' upstream is responsive to ethylene and only two root-specific expression elements, among the several detected, are functional but redundant. Conservation of molecular mechanisms between sunflower and Arabidopsis is strongly supported by this experimental work.

Investigation of some trace elements in drinking water: Nuba Mountains Section, Sudan

International Nuclear Information System (INIS)

Elgorashe, R.E.E.

2008-09-01

This study was conducted to assess the extent of pollution in the drinking water from various sources at the area of the Nuba Mountains, Sudan. 42 samples were collected from hand pump stations, water yard (diesel machine) stations and surface water (lake) stations.These waters were analyzed using atomic absorption spectrophotometer. The concentrations of iron, nickel, copper, manganese, magnesium, zinc and chromium were determined using flame atomic spectroscopy, while the concentrations of cadmium and lead were determined by furnace atomic spectroscopy. The mean concentrations of iron, nickel, lead, copper, manganese, magnesium, zinc and chromium in water samples collected from hand pump stations were 1.901, 0.010, 0.1310, 0.0070, 0.0410, 20.35, 0.558 and 0.0430 mg/L respectively. And in samples collected from water yard stations were found to be 0.871, 0.013, 0.438, 0.209, 0.128, 28.41, 0.103 and 0.032 mg/L for iron, nickel, lead, copper, manganese, magnesium, zinc and chromium respectively. And in samples collected from surface water station were found to be 13.74, 0.023, 0.015, 0.017, 0.118, 7.008, 0.042 and 0.0002 mg/L for iron, nickel, lead, copper, manganese, magnesium, zinc and chromium respectively. The concentrations of cadmium were found below detection of limits. Mean concentrations of elements from different sources were compared using the Kruskal - wallis method. This study showed that there are significant different between mean concentrations for these elements. The spear man correlation method was identified between elements. Correlation study shows that there is a significant positive correlation between iron and chromium. Comparison between those data and the specific criterion specifies drinking water by the World Health Organization (WHO) showed that the concentrations of Pb are exceeding the maximum permissible levels in eighteen stations. Violations of drinking water limits were observed also for the elements Mn in six stations and Cr in

Investigation of some trace elements in drinking water: Nuba Mountains Section, Sudan

Energy Technology Data Exchange (ETDEWEB)

Elgorashe, R E.E. [Coordination Council of Sudan Atomic Energy Commission, Sudan Academy of Sciences, Khartoum (Sudan)

2008-09-15

This study was conducted to assess the extent of pollution in the drinking water from various sources at the area of the Nuba Mountains, Sudan. 42 samples were collected from hand pump stations, water yard (diesel machine) stations and surface water (lake) stations.These waters were analyzed using atomic absorption spectrophotometer. The concentrations of iron, nickel, copper, manganese, magnesium, zinc and chromium were determined using flame atomic spectroscopy, while the concentrations of cadmium and lead were determined by furnace atomic spectroscopy. The mean concentrations of iron, nickel, lead, copper, manganese, magnesium, zinc and chromium in water samples collected from hand pump stations were 1.901, 0.010, 0.1310, 0.0070, 0.0410, 20.35, 0.558 and 0.0430 mg/L respectively. And in samples collected from water yard stations were found to be 0.871, 0.013, 0.438, 0.209, 0.128, 28.41, 0.103 and 0.032 mg/L for iron, nickel, lead, copper, manganese, magnesium, zinc and chromium respectively. And in samples collected from surface water station were found to be 13.74, 0.023, 0.015, 0.017, 0.118, 7.008, 0.042 and 0.0002 mg/L for iron, nickel, lead, copper, manganese, magnesium, zinc and chromium respectively. The concentrations of cadmium were found below detection of limits. Mean concentrations of elements from different sources were compared using the Kruskal - wallis method. This study showed that there are significant different between mean concentrations for these elements. The spear man correlation method was identified between elements. Correlation study shows that there is a significant positive correlation between iron and chromium. Comparison between those data and the specific criterion specifies drinking water by the World Health Organization (WHO) showed that the concentrations of Pb are exceeding the maximum permissible levels in eighteen stations. Violations of drinking water limits were observed also for the elements Mn in six stations and Cr in

The role of high-energy synchrotron radiation in biomedical trace element research

International Nuclear Information System (INIS)

Pounds, J.G.; Long, G.J.; Kwiatek, W.M.; Jones, K.W.; Gordon, B.M.; Hanson, A.L.

1987-01-01

This paper will present the results of an investigation of the distribution of essential elements in the normal hepatic lobule. the liver is the organ responsible for metabolism and storage of most trace elements. Although parenchymal hepatocytes are rather uniform histologically, morphometry, histochemistry, immunohistochemistry, and microdissection with microchemical investigations have revealed marked heterogeneity on a functional and biochemical level. Hepatocytes from the periportal and perivenous zones of the liver parrenchyma differ in oxidative energy metabolism, glucose uptake and output, unreagenesis, biotransformation, bile acid secretion, and palsma protein synthesis and secretion. Although trace elements are intimately involved in the regulation and maintenance of these functions, little is known regarding the heterogeneity of trace element localization of the liver parenchyma. Histochemical techniques for trace elements generally give high spatial resolution, but lack specificity and stoichiometry. Microdissection has been of marginal usefulness for trace element analyses due to the very small size of the dissected parenchyma. The characteristics of the high-energy x-ray microscope provide an effective approach for elucidating the trace element content of these small biological structures or regions. 5 refs., 1 fig., 1 tab

Population diversity of ammonium oxidizers investigated by specific PCR amplification

Science.gov (United States)

Ward, B.B.; Voytek, M.A.; Witzel, K.-P.

1997-01-01

The species composition of ammonia-oxidizing bacteria in aquatic environments was investigated using PCR primers for 16S rRNA genes to amplify specific subsets of the total ammonia-oxidizer population. The specificity of the amplification reactions was determined using total genomic DNA from known nitrifying strains and non-nitrifying strains identified as having similar rDNA sequences. Specificity of amplification was determined both for direct amplification, using the nitrifier specific primers, and with nested amplification, in which the nitrifier primers were used to reamplify a fragment obtained from direct amplification with Eubacterial universal primers. The present level of specificity allows the distinction between Nitrosomonas europaea, Nitrosomonas sp. (marine) and the other known ammonia-oxidizers in the beta subclass of the Proteobacteria. Using total DNA extracted from natural samples, we used direct amplification to determine presence/absence of different species groups. Species composition was found to differ among depths in vertical profiles of lake samples and among samples and enrichments from various other aquatic environments. Nested PCR yielded several more positive reactions, which implies that nitrifier DNA was present in most samples, but often at very low levels.

Diglycolamide-functionalized task specific ionic liquids for nuclear waste remediation: extraction, luminescence, theoretical and EPR investigations

NARCIS (Netherlands)

Sengupta, A; Mohapatra, P.K.; Kadam, R.M.; Manna, D.; Ghanty, T.K.; Iqbal, M.; Huskens, Jurriaan; Verboom, Willem

2014-01-01

A 3.6 × 10−2 M solution of a diglycolamide-functionalized task specific ionic liquid (DGA-TSIL) in [C4mim][NTf2] was used for the extraction of actinides (mainly Am) and other elements present in high level nuclear waste. The extraction of Eu3+ was relatively higher than that of Am3+ conforming to

Investigation of deformation of elements of three-dimensional reinforced concrete structures located in the soil, interacting with each other through rubber gaskets

Science.gov (United States)

Berezhnoi, D. V.; Balafendieva, I. S.; Sachenkov, A. A.; Sekaeva, L. R.

2017-06-01

In work the technique of calculation of elements of three-dimensional reinforced concrete substructures located in a soil, interacting with each other through rubber linings is realized. To describe the interaction of deformable structures with the ground, special “semi-infinite” finite elements are used. A technique has been implemented that allows one to describe the contact interaction of three-dimensional structures by means of a special contact finite element with specific properties. The obtained numerical results are compared with the experimental data, their good agreement is noted.

Investigation of elements accumulation in some plants by nuclear-research methods

International Nuclear Information System (INIS)

Azhabov, A.K.; Khushmuradov, Sh.Kh.; Danilova, E.A.; Kist, A.A.; Dekhkanov, T.; Kobzev, A.P.; Muminov, I.T.

2000-01-01

The results of studies on 18 elements in the samples of hugh elecampane, middle-asian mint, field horsetail, mixed grass crop and turkestan dog rose fruits, collected at the two stationary sites A and B of the Bashkizylsaj area of the Chatkalsk biospheric reservation and studied through the neutron-activation (n), γ-activation (γ), X-ray spectral (p) and X-ray fluorescence (x) physical methods, are presented. The root-square errors of the results, obtained by different method and differences in the elements accumulation, depending on the plant type, their part and vegetation place, are evaluated. The coefficients of biological accumulation of 15 elements in the 15 plants under study are determined on the basis of the data on the elements content in plants and corresponding soil samples [ru

Chalcogenides formed by trivalent rare earth elements with d-elements

International Nuclear Information System (INIS)

Flao, Zh.; Laruehl', P.; Olitro, R.

1981-01-01

Data on ternary compounds formed by trivalent rare earth elements with 3d-, 4d- and 5d-elements of the Periodic system is presented. Compounds of 3d-elements both in bivalent and trivalent states are considered. The main attention is paid to the structure of the compounds. Description of a great number of new structural types of compounds is given. In certain cases the structure has not been deciphered and, besides, structural investigations with monocrystals are not numerous. Attention is drawn to the existence of nonstoichiometric compounds. References to the works on investigation of thermal (melting temperature), magnetic, optical and electric properties as well as Moessbauer effect are presented

SPECIFIC DEGRADATION STRUCTURE FEATURES AND MECHANICAL PROPERTIES OF FURNACE AND HEAT POWER EQUIPMENT ELEMENTS AFTER LONG-TERM OPERATION

Directory of Open Access Journals (Sweden)

F. I. Panteleenko

2012-01-01

Full Text Available The paper presents results of investigations on structure and mechanical properties of technological equipment elements made of heat-resistant steels. A scale of chrome and molybdenum steel microstructure degradation based on evaluation of  coagulated carbide size and material mechanical properties (a point from 0-operation without time limits, up to 4-operation prohibition has been proposed in the paper. It has been  established that an analysis of  steel microstructure directly on equipment elements by means of a portable microscope is an efficient express method for evaluation of equipment condition and structures due to control of material structure degradation rate of a diagnosed object.

Investigation Of Interaction Between Nitinol Stent And A Vascular Plaque Using Finite Element Method

Directory of Open Access Journals (Sweden)

Recep Güneş

2012-06-01

Full Text Available In this study, the interaction between the Nitinol stent and the artery with plaque was investigated using finite element method. The occurring pressure values during the cardiac contraction (systolic and loosening (diastolic were applied as loading to the modeled system with Nitinol stent. In the light of the stress values, the suitability of the Nitinol stent in an artery with plaque was investigated. In the analysis, Nitinol stent was assumed to be shape memory alloy, and artery and plaque were assumed to behave linearly elastic. As a result, the stress and deformations in the plaque and artery due to the interference of Nitinol stent were discussed and concluded that the structure of artery with plaque can be expanded in accordance with Nitinol stent.

Finite element investigation of the prestressed jointed concrete ...

African Journals Online (AJOL)

Precast prestressed concrete pavement (PCP) technology is of recent origin, and the information on PCP performance is not available in literature. This research presents a finite-element analysis of the potential benefits of prestressing on the jointed concrete pavements (JCP). With using a 3-dimensional (3D) ...

Biological toxicity of lanthanide elements on algae.

Science.gov (United States)

Tai, Peidong; Zhao, Qing; Su, Dan; Li, Peijun; Stagnitti, Frank

2010-08-01

The biological toxicity of lanthanides on marine monocellular algae was investigated. The specific objective of this research was to establish the relationship between the abundance in the seawater of lanthanides and their biological toxicities on marine monocellular algae. The results showed that all single lanthanides had similar toxic effects on Skeletonema costatum. High concentrations of lanthanides (29.04+/-0.61 micromol L(-1)) resulted in 50% reduction in growth of algae compared to the controls (0 micromol L(-1)) after 96 h (96 h-EC50). The biological toxicity of 13 lanthanides on marine monocellular algae was unrelated with the abundance of different lanthanide elements in nature, and the "Harkins rule" was not appropriate for the lanthanides. A mixed solution that contained equivalent concentrations of each lanthanide element had the same inhibition effect on algae cells as each individual lanthanide element at the same total concentration. This phenomenon is unique compared to the groups of other elements in the periodic table. Hence, we speculate that the monocellular organisms might not be able to sufficiently differentiate between the almost chemically identical lanthanide elements. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Investigation of the Behavior of Steel Shear Walls Using Finite Elements Analysis

Directory of Open Access Journals (Sweden)

K. Abubakri

2016-10-01

Full Text Available Currently, steel shear walls are considered by engineers as an economic method against lateral loads imposed by wind and earthquake in tall structures. Accordingly, there is a growing need to develop accurate methods alongside approximation methods to estimate the behavior of these structural elements. The finite element technique is one of the strongest numerical methods in analysis of solid mechanics problems. Finite element analysis however requires high technical knowledge of the behavioral models of materials. Therefore, it is less used by designers for certain structural elements such as steel shear walls. This study examines the failure mechanism of steel shear walls using finite elements analysis and validates this modeling by comparing the results with experimental studies.

Transposable elements generate population-specific insertional patterns and allelic variation in genes of wild emmer wheat (Triticum turgidum ssp. dicoccoides).

Science.gov (United States)

Domb, Katherine; Keidar, Danielle; Yaakov, Beery; Khasdan, Vadim; Kashkush, Khalil

2017-10-27

Natural populations of the tetraploid wild emmer wheat (genome AABB) were previously shown to demonstrate eco-geographically structured genetic and epigenetic diversity. Transposable elements (TEs) might make up a significant part of the genetic and epigenetic variation between individuals and populations because they comprise over 80% of the wild emmer wheat genome. In this study, we performed detailed analyses to assess the dynamics of transposable elements in 50 accessions of wild emmer wheat collected from 5 geographically isolated sites. The analyses included: the copy number variation of TEs among accessions in the five populations, population-unique insertional patterns, and the impact of population-unique/specific TE insertions on structure and expression of genes. We assessed the copy numbers of 12 TE families using real-time quantitative PCR, and found significant copy number variation (CNV) in the 50 wild emmer wheat accessions, in a population-specific manner. In some cases, the CNV difference reached up to 6-fold. However, the CNV was TE-specific, namely some TE families showed higher copy numbers in one or more populations, and other TE families showed lower copy numbers in the same population(s). Furthermore, we assessed the insertional patterns of 6 TE families using transposon display (TD), and observed significant population-specific insertional patterns. The polymorphism levels of TE-insertional patterns reached 92% among all wild emmer wheat accessions, in some cases. In addition, we observed population-specific/unique TE insertions, some of which were located within or close to protein-coding genes, creating allelic variations in a population-specific manner. We also showed that those genes are differentially expressed in wild emmer wheat. For the first time, this study shows that TEs proliferate in wild emmer wheat in a population-specific manner, creating new alleles of genes, which contribute to the divergent evolution of homeologous genes

Measurement and analysis of vibrational behaviour of an SNR-fuel element in sodium flow

International Nuclear Information System (INIS)

Hess, B.F.H.; Ruppert, E.; Schmidt, H.; Vinzens, K.

1975-01-01

Within the framework of SNR-300 fuel element development programme a complete full size fuel element dummy has been tested thoroughly for nearly 3000 hours at 650 0 C system temperature in the AKB sodium loop at Interatom, Bensberg. Investigations of the hydraulic characteristics by measurements of specific pressure losses, flow velocities, leakage flow through the piston rings and investigations of its vibrational behaviour were part of this endurance test at elevated temperatures. The pressure drop versus flow and the leakage measurement are mentioned briefly to confirm the correctness of the test hydraulics. The vibrational behaviour of the element and the approach to analysis is the main object of this report. (Auth.)

Elemental analysis of biological tissues of animal models in muscular dystrophies investigation

International Nuclear Information System (INIS)

Sabrina Metairon; Zamboni, C.B.; Suzuki, M.F.; Bueno, Jr.C.R.; Sant'Anna, O.A.

2012-01-01

Element concentrations in biological tissues of Dmd mdx /J and C57BL/6 J mice strains were determined using the neutron activation analysis technique. Samples of whole blood, bones and organs (heart and muscle) of these strains were irradiated in the IEA-R1 nuclear reactor at IPEN-CNEN/SP (Brazil). To perform this investigation biological samples of two-month-old adult females (n = 10) and males (n = 9) for Dmd mdx /J (dystrophic mice), and males (n 12) for C57BL/6 J (control group), originally obtained from the Jackson Laboratory (Maine, USA) and further inbred at IPEN-CNEN/SP (Sao Paulo, Brazil), were used. A significant change was observed in the analysis of the heart of dystrophic mice suggesting that this dysfunction affects severely the heart muscle. These data may, in the future, contribute to the healthcare area, in veterinary medicine and in the pharmaceutical industry allowing the evaluation of the best procedures in diagnosis, treatment and investigations of neuromuscular diseases (muscular dystrophy) of patients through the use of animal models. (author)

Triple-element compound-specific stable isotope analysis of 1,2-dichloroethane for characterization of the underlying dehalogenation reaction in two Dehalococcoides mccartyi strains.

Science.gov (United States)

Franke, Steffi; Lihl, Christina; Renpenning, Julian; Elsner, Martin; Nijenhuis, Ivonne

2017-12-01

Chlorinated ethanes belong to the most common groundwater and soil contaminants. Of these, 1,2-dichloroethane (1,2-DCA) is a man-made, persistent and toxic contaminant, released due to improper waste treatment at versatile production sites. This study investigated the anaerobic transformation of 1,2-DCA by Dehalococcoides mccartyi strain 195 and strain BTF08 using triple-element compound-specific stable isotope analysis of carbon, chlorine and hydrogen for the first time. Isotope fractionation patterns for carbon (εCBTF08 = -28.4 ± 3.7‰; εC195 = -30.9 ± 3.6‰) and chlorine (εClBTF08 = -4.6 ± 0.7‰; εCl195 = -4.2 ± 0.5‰) within both investigated D. mccartyi strains, as well as the dual-element analysis (ΛBTF08 = 6.9 ± 1.2; Λ195 = 7.1 ± 0.2), supported identical reaction mechanisms for dehalogenation of 1,2-DCA. Hydrogen isotope fractionation analysis revealed dihaloelimination as prevalent reaction mechanism. Vinyl chloride as major intermediate could be excluded by performing the experiment in deuterated aqueous media. Furthermore, evaluation of the derived apparent kinetic isotope effects (AKIECBTF08 = 1.029/AKIEC195 = 1.031; AKIEClBTF08 = 1.005/AKIECl195 = 1.004) pointed towards simultaneous abstraction of both involved chlorine-substituents in a concerted matter. It was shown that D. mccartyi strain BTF08 and strain 195 are capable of complete, direct dihaloelimination of 1,2-DCA to ethene. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Essential Specification Elements for Heat Exchanger Replacement

Energy Technology Data Exchange (ETDEWEB)

Bower, L.

2015-07-01

Performance upgrade and equipment degradation are the primary impetuses for a nuclear power plant to engage in the large capital cost project of heat exchanger replacement. Along with attention to these issues, consideration of heat exchanger Codes and Standards, material improvements, thermal redesign, and configuration are essential for developing User’s Design Specifications for successful replacement projects. The User’s Design Specification is the central document in procuring ASME heat exchangers. Properly stated objectives for the heat exchanger replacement are essential for obtaining the materials, configurations and thermal designs best suited for the nuclear power plant. Additionally, the code of construction required and the applied manufacturing standard (TEMA or HEI) affects how the heat exchanger may be designed or configured to meet the replacement goals. Knowledge of how Codes and Standards affect design and configuration details will aid in writing the User’s Design Specification. Joseph Oat Corporation has designed and fabricated many replacement heat exchangers for the nuclear power industry. These heat exchangers have been constructed per ASME Section III to various Code-Years or ASME Section VIII-1 to the current Code-Year also in accordance with TEMA and HEI. These heat exchangers have been a range of like-for-like replacement to complete thermal, material and configuration redesigns. Several examples of these heat exchangers with their Code, Standard and specification implications are presented. (Author.

Detailed SEM-EPMA investigation of high specific radioactivity particles (hot particles)

International Nuclear Information System (INIS)

Burin, K.; Tsacheva, Ts.; Mandjoukov, I.; Mandjoukova, B.

1993-01-01

Scanning electron microscope (SEM) images and electron probe microanalysis (EPMA) spectra of a group of hot particles collected in Bulgaria after the Chernobyl accident have been obtained. A technique for hot particle localization is described. The object is irradiated for two days with a β source and the resulting autoradiographs show particles location precisely. High resolution x-ray spectrum of each particle has been obtained using EPMA. The distribution of chemical elements is visualized by colour dot maps representing the regions of interest of the spectrum. It is concluded that apart from reactor fuel the investigated hot particles come from either construction materials or materials used for the covering of the damaged reactor. 7 figs., 2 ref

The investigation of ferromagnetic resonance linewidth in Ni{sub 80}Fe{sub 20} films with submicron rectangular elements

Energy Technology Data Exchange (ETDEWEB)

Zhang, D. [Department of Physics, Southeast University, Nanjing, 211189 (China); School of Physical Science and Information Engineering, Liaocheng University, Liaocheng, 252059 (China); Yue, J. J.; Kou, Z. X.; Lin, L. [Department of Physics, Southeast University, Nanjing, 211189 (China); Zhai, Y., E-mail: yazhai@seu.edu.cn [Department of Physics, Southeast University, Nanjing, 211189 (China); National Laboratory of Solid Microstructures, Nanjing University, Nanjing, 210093 (China); Zhai, H. R. [National Laboratory of Solid Microstructures, Nanjing University, Nanjing, 210093 (China)

2016-05-15

Patterned magnetic films with nano-scaled dots exhibit some special magnetic properties. In this paper, we investigate the in-plane shape anisotropy and the magnetization dynamic damping in permalloy (Ni{sub 80}Fe{sub 20}) arrays of submicron rectangular elements using ferromagnetic resonance (FMR). The FMR linewidth exhibits a dependence on the element size, and mainly comes from the contribution of the intrinsic damping. Also the contribution of two-magnon scattering plays an important role and is reduced with increasing aspect ratio. The damping coefficient decreases from 0.0129 to 0.0118 with the element length increasing from 300 nm to 1200 nm, and the theoretical calculation suggests that the change of damping results from the longitudinal and transverse interlayer spin current due to the spatially inhomogeneous magnetization dynamics.

Specific investigations related to salt rock behaviour

International Nuclear Information System (INIS)

Vons, L.H.

1985-01-01

In this paper results are given of work in various countries in rather unrelated areas of research. Nevertheless, since the studies have been undertaken to better understand salt behaviour, both from mechanical and chemical points of view, some connection between the studies can be found. In the French contribution the geological conditions have been investigated that might promote or prevent the formation of salt domes from layers in view of possible use of the latter type of formation. This was done theoretically by the finite element method, and a start was made with centrifuge tests. The density of a number of samples from salt and overburden from the Bresse basin was measured and it was shown that a favourable condition exists in this region for waste disposal. In the German contribution various subjects are touched upon, one being the effect of water on the mobility in the early stages of salt dome formation. Evidence was found for an anisotropy in salt. One Dutch contribution describes results of studies on the effect of small amounts of water on the rheology of salt. The results imply that flow laws obtained for salt at rapid strain rates and/or low confining pressure cannot be reliably extrapolated to predict the long term behaviour of wet or even very dry material under natural conditions. Preliminary results on the effect of water upon ion-mobility indicate a certain pseudo-absorptive capacity of salt e.g. for Sr

Sensitivity analysis of a validated subject-specific finite element model of the human craniofacial skeleton.

Science.gov (United States)

Szwedowski, T D; Fialkov, J; Whyne, C M

2011-01-01

Developing a more complete understanding of the mechanical response of the craniofacial skeleton (CFS) to physiological loads is fundamental to improving treatment for traumatic injuries, reconstruction due to neoplasia, and deformities. Characterization of the biomechanics of the CFS is challenging due to its highly complex structure and heterogeneity, motivating the utilization of experimentally validated computational models. As such, the objective of this study was to develop, experimentally validate, and parametrically analyse a patient-specific finite element (FE) model of the CFS to elucidate a better understanding of the factors that are of intrinsic importance to the skeletal structural behaviour of the human CFS. An FE model of a cadaveric craniofacial skeleton was created from subject-specific computed tomography data. The model was validated based on bone strain measurements taken under simulated physiological-like loading through the masseter and temporalis muscles (which are responsible for the majority of craniofacial physiologic loading due to mastication). The baseline subject-specific model using locally defined cortical bone thicknesses produced the strongest correlation to the experimental data (r2 = 0.73). Large effects on strain patterns arising from small parametric changes in cortical thickness suggest that the very thin bony structures present in the CFS are crucial to characterizing the local load distribution in the CFS accurately.

Application of the X-ray analyses on bioaccumulation and biomineralization for the specific elements

Energy Technology Data Exchange (ETDEWEB)

Numako, Chiya [Tokushima Univ., Faculty of Integrated Arts and Sciences, Tokushima (Japan)

2003-03-01

Specific accumulation of the elements by biological activity has a large influence on a material recycling on the earth. Some non-distractive characterizations by X-ray spectroscopy, XRF and/or XAFS measurements with synchrotron radiation have been applied to some solid state specimens which accumulate heavy metals at high concentration in order to elucidate its mechanism or purpose of the phenomena for each marine creature. It has been known that a few bivalves including giant clams stock kidney granules that accumulate Mn and Zn specifically. The results of two-dimensional elemental analyses by EPMA indicate zoning structures of the concentration of Mn, Zn and Mg negative correlation between Mg and (Mn + Zn) inside of a granule. Fluorescence XAFS analyses for Mn and Zn in the kidney granules, held at BL-7C, PF, KEK, shows that Mn and Zn exist as divalent cations in amorphous calcium phosphate matrix. It is considered that Mn and Zn have got a detoxication by substitution for Mg into amorphous calcium phosphate with flexible crystal structure. The teeth of chiton, which accumulate magnetite as a major substance of the teeth, have been also studied by SR-XRF and micro XAFS technique with microbeam focused in 6 {mu}m {phi} from undulator at SPring-8, BL-39XU. In the early stage of the teeth formation, abrupt accumulation of Fe into a feeding plane of a tooth, while the concentration of Ca has been remained equally at the back of a tooth. Micro-XAFS measurement for Fe in the teeth indicates that a major material of the feeding plane is magnetite while trivalent iron compounds appears along the junction zone of the tooth and a base membrane. There is a complex scheme in the tooth formation of chiton, which is available to create some kinds of iron species and allocates those into different positions in a tooth. (author)

Application of the X-ray analyses on bioaccumulation and biomineralization for the specific elements

International Nuclear Information System (INIS)

Numako, Chiya

2003-01-01

Specific accumulation of the elements by biological activity has a large influence on a material recycling on the earth. Some non-distractive characterizations by X-ray spectroscopy, XRF and/or XAFS measurements with synchrotron radiation have been applied to some solid state specimens which accumulate heavy metals at high concentration in order to elucidate its mechanism or purpose of the phenomena for each marine creature. It has been known that a few bivalves including giant clams stock kidney granules that accumulate Mn and Zn specifically. The results of two-dimensional elemental analyses by EPMA indicate zoning structures of the concentration of Mn, Zn and Mg negative correlation between Mg and (Mn + Zn) inside of a granule. Fluorescence XAFS analyses for Mn and Zn in the kidney granules, held at BL-7C, PF, KEK, shows that Mn and Zn exist as divalent cations in amorphous calcium phosphate matrix. It is considered that Mn and Zn have got a detoxication by substitution for Mg into amorphous calcium phosphate with flexible crystal structure. The teeth of chiton, which accumulate magnetite as a major substance of the teeth, have been also studied by SR-XRF and micro XAFS technique with microbeam focused in 6 μm φ from undulator at SPring-8, BL-39XU. In the early stage of the teeth formation, abrupt accumulation of Fe into a feeding plane of a tooth, while the concentration of Ca has been remained equally at the back of a tooth. Micro-XAFS measurement for Fe in the teeth indicates that a major material of the feeding plane is magnetite while trivalent iron compounds appears along the junction zone of the tooth and a base membrane. There is a complex scheme in the tooth formation of chiton, which is available to create some kinds of iron species and allocates those into different positions in a tooth. (author)

Species-and stage-specific differences in trace element tissue concentrations in amphibians: implications for the disposal of coal-combustion wastes

International Nuclear Information System (INIS)

Roe, John H.; Hopkins, William A.; Jackson, Brian P.

2005-01-01

Information on species-and stage-specific patterns of contaminant accumulation is generally lacking for amphibians, yet such information could provide valuable knowledge on how amphibians interact with contaminants. We assessed concentrations of As, Cd, Cu, Ni, Pb, Se, Sr, and Zn in whole bodies of larval, recently metamorphosed, and adult life stages in Bufo terrestris and Rana sphenocephala from a site that currently receives coal combustion waste (CCW) discharge, a site where CCW was formerly discharged that has undergone natural attenuation for 30 years, and a nearby reference site. For the majority of elements (As, Cd, Cu, Ni, Pb, Zn), concentrations were highest in larvae, but Se and Sr concentrations remained elevated in later life stages, likely because these elements are S and Ca analogs, respectively, and are thus retained throughout structural changes during metamorphosis. Element concentrations were generally higher in B. terrestris than in R. sphenocephala. Concentrations of As, Se, and Sr were up to 11-35 times higher in metamorphs emigrating from CCW-polluted wetlands compared to unpolluted wetlands, suggesting metamorphosed amphibians can transport trace elements from aquatic disposal basins to nearby uncontaminated terrestrial habitats. In addition, anurans utilizing naturally revegetated sites up to 30 years after CCW disposal ceases are exposed to trace elements, although to a lesser degree than sites where CCW is currently discharged. - Results suggest that metamorphosed amphibians can transport trace elements from aquatic disposal basins to non-contaminated habitats

Species-and stage-specific differences in trace element tissue concentrations in amphibians: implications for the disposal of coal-combustion wastes

Energy Technology Data Exchange (ETDEWEB)

Roe, John H. [University of Georgia, Savannah River Ecology Laboratory, P.O. Drawer E, Aiken, SC 29802 (United States); Hopkins, William A. [University of Georgia, Savannah River Ecology Laboratory, P.O. Drawer E, Aiken, SC 29802 (United States)]. E-mail: hopkins@srel.edu; Jackson, Brian P. [University of Georgia, Savannah River Ecology Laboratory, P.O. Drawer E, Aiken, SC 29802 (United States)

2005-07-15

Information on species-and stage-specific patterns of contaminant accumulation is generally lacking for amphibians, yet such information could provide valuable knowledge on how amphibians interact with contaminants. We assessed concentrations of As, Cd, Cu, Ni, Pb, Se, Sr, and Zn in whole bodies of larval, recently metamorphosed, and adult life stages in Bufo terrestris and Rana sphenocephala from a site that currently receives coal combustion waste (CCW) discharge, a site where CCW was formerly discharged that has undergone natural attenuation for 30 years, and a nearby reference site. For the majority of elements (As, Cd, Cu, Ni, Pb, Zn), concentrations were highest in larvae, but Se and Sr concentrations remained elevated in later life stages, likely because these elements are S and Ca analogs, respectively, and are thus retained throughout structural changes during metamorphosis. Element concentrations were generally higher in B. terrestris than in R. sphenocephala. Concentrations of As, Se, and Sr were up to 11-35 times higher in metamorphs emigrating from CCW-polluted wetlands compared to unpolluted wetlands, suggesting metamorphosed amphibians can transport trace elements from aquatic disposal basins to nearby uncontaminated terrestrial habitats. In addition, anurans utilizing naturally revegetated sites up to 30 years after CCW disposal ceases are exposed to trace elements, although to a lesser degree than sites where CCW is currently discharged. - Results suggest that metamorphosed amphibians can transport trace elements from aquatic disposal basins to non-contaminated habitats.

Evolutionary origin of Rosaceae-specific active non-autonomous hAT elements and their contribution to gene regulation and genomic structural variation.

Science.gov (United States)

Wang, Lu; Peng, Qian; Zhao, Jianbo; Ren, Fei; Zhou, Hui; Wang, Wei; Liao, Liao; Owiti, Albert; Jiang, Quan; Han, Yuepeng

2016-05-01

Transposable elements account for approximately 30 % of the Prunus genome; however, their evolutionary origin and functionality remain largely unclear. In this study, we identified a hAT transposon family, termed Moshan, in Prunus. The Moshan elements consist of three types, aMoshan, tMoshan, and mMoshan. The aMoshan and tMoshan types contain intact or truncated transposase genes, respectively, while the mMoshan type is miniature inverted-repeat transposable element (MITE). The Moshan transposons are unique to Rosaceae, and the copy numbers of different Moshan types are significantly correlated. Sequence homology analysis reveals that the mMoshan MITEs are direct deletion derivatives of the tMoshan progenitors, and one kind of mMoshan containing a MuDR-derived fragment were amplified predominately in the peach genome. The mMoshan sequences contain cis-regulatory elements that can enhance gene expression up to 100-fold. The mMoshan MITEs can serve as potential sources of micro and long noncoding RNAs. Whole-genome re-sequencing analysis indicates that mMoshan elements are highly active, and an insertion into S-haplotype-specific F-box gene was reported to cause the breakdown of self-incompatibility in sour cherry. Taken together, all these results suggest that the mMoshan elements play important roles in regulating gene expression and driving genomic structural variation in Prunus.

Species- and stage-specific differences in trace element tissue concentrations in amphibians: implications for the disposal of coal-combustion wastes

Energy Technology Data Exchange (ETDEWEB)

Roe, J.H.; Hopkins, W.A.; Jackson, B.P. [University of Georgia, Aiken, SC (US)

2005-07-01

Information on species- and stage-specific patterns of contaminant accumulation is generally lacking for amphibians, yet such information could provide valuable knowledge on how amphibians interact with contaminants. We assessed concentrations of As, Cd, Cu, Ni, Pb, Se, Sr, and Zn in whole bodies of larval, recently metamorphosed, and adult life stages in Bufo terrestris and Rana sphenocephala from a site that currently receives coal combustion waste (CCW) discharge, a site where CCW was formerly discharged that has undergone natural attenuation for 30 years, and a nearby reference site. For the majority of elements (As, Cd, Cu, Ni, Pb, Zn), concentrations were highest in larvae, but Se and Sr concentrations remained elevated in later life stages, likely because these elements are S and Ca analogs, respectively, and are thus retained throughout structural changes during metamorphosis. Element concentrations were generally higher in B. terrestris than in R. sphenocephala. Concentrations of As, Se, and Sr were up to 11-35 times higher in metamorphs emigrating from CCW-polluted wetlands compared to unpolluted wetlands, suggesting metamorphosed amphibians can transport trace elements from aquatic disposal basins to nearby uncontaminated terrestrial habitats. In addition, anurans utilizing naturally revegetated sites up to 30 years after CCW disposal ceases are exposed to trace elements, although to a lesser degree than sites where CCW is currently discharged.

Thermal-hydraulic investigations of fuel elements

International Nuclear Information System (INIS)

Rehme, K.; Weinberg, D.

1983-01-01

Extensive fluid-dynamic examining of flow distribution and turbulent flow distribution was done to control and safeguard calculation methods allowing the determination of three-dimensional flow distribution in fuel elements. Results show that the flow distribution greatly depends on the frequency of pulse exchange between subchannels in narrow rod grids. The comparison of these measured values to VELASCO's results shows that the calculation methods need to be considerably improved. The subchannel analysis proved to be very suitable to calculate mean flow temperatures conforming with the subchannel analysis principle. However, this does not include statements on wall temperatures occurring in the structures. Mean wall temperatures can be determined by empirical interrelationships for Nusseltnumbers. On the other hand, the calculation of detailed wall temperature distributions is not possible with the subchannel analysis unless it can be further improved due to more detailed measurement results. (orig.) [de

Finite Element Modeling of an Aircraft Tire Rolling on a Steel Drum: Experimental Investigations and Numerical Simulations

Directory of Open Access Journals (Sweden)

Iulian Rosu

2018-04-01

Full Text Available The aim of this study is to investigate the thermal evolution of an aircraft tire rolling at high velocities up to take off values. As this kind of experiment is difficult to realize on a real runway, experimental tests were realized on aircraft tires rolling on a steel drum. The rotating drum facility allows to apply variable velocities beyond the take off limits, at fixed skidding angles and loadings. The rolling conditions, vertical loading, velocity and cornering conditions were adopted to correspond to the real conditions of an aircraft tire running or skidding on a flat runway. In the experimental part, the influence of skidding angle, velocity and loading on the thermal evolution of the tire tread were investigated. The thermo-mechanical finite element analysis of a pneumatic radial tire structure was performed taking into account the hyper-viscoelastic rubber behavior, with heating mechanisms developed by the inelastic deformation and by friction. Three-dimensional finite element simulations of an aircraft tire rolling on a steel drum were carried out using Abaqus/Standard finite element solver. The comparison of the temperature distribution on the tire tread between numerical results and the experimental data shows the same overall tendencies. The good correlation between numerical and experimental data shows that numerical simulation could predict the thermal evolution of the tire in critical situations. The authors would like to mention that for confidentiality reason, certain numerical data could not be revealed.

Exploration of new biological specific function by heavy elements stimulus

International Nuclear Information System (INIS)

Macaskie, Lynne; Renshaw, Joanna; Ohnuki, Toshihiko; Nishiguchi, Norihiko; Utsunomiya, Satoshi; Suzuki, Yoshinori; Shirai, Osamu

2014-01-01

We have carried out experiments to investigate bio-mineralization of rare earth elements (REE) on the cell surface of yeast Saccharomyces cerevisiae, and the bacteria Bacillus subtilis, Pseudomonas fluorescens and Serratia sp. The continuous removal of 1 mM La (100%) Nd (100%) and Eu (>80%) was observed using a continuous flow through immobilized Serratia sp cell columns. Chemical and physical characterization of bio-mineralized La and Eu was done by XRD at Birmingham and showed the formation of phosphate minerals. Additional cell column work using S. cerevisiae, B. subtilis, or P. fluorescens, showed that these bacteria are capable of bio-mineralizing Ce(III) and Sm(III). Chemical and physical characterizations of bio-transformed Ce and Sm were analyzed by JAEA, Kyushu U., Tokyo U. Tech. and Kyoto U. using XAFS, SEM and TEM. Results showed that Ce and Sm nanoparticles were formed. The high radiostability of the metal accumulating enzyme of Serratia sp. (which promotes metal phosphate deposition) was shown in whole cells, whereas pure enzyme lost its activity quickly under irradiation. Additional work on radionuclide (Cm) incorporation into Serratia sp calcium phosphate minerals (analogue for human bones) using EXAFS and Time Resolved Laser Fluorescence Spectroscopy (in collaboration with Karlsruhe Institute of Technology) showed that this actinide binds at the grain boundaries between crystallites, which has health implications for human exposure. (author)

Exploration of new biological specific function by heavy elements stimulus

International Nuclear Information System (INIS)

Macaskie, Lynne; Renshaw, Joanna; Ohnuki, Toshihiko; Nishiguchi, Norihiko; Utsunomiya, Satoshi; Suzuki, Yoshinori; Shirai, Osamu

2012-01-01

We have carried out experiments to investigate bio-mineralization of rare earth elements (REE) on the cell surface of yeast Saccharomyces cerevisiae, and the bacteria Bacillus subtilis, Pseudomonas fluorescens and Serratia sp. The continuous removal of 1 mM La (100%) Nd (100%) and Eu(>80%) was observed using a continuous flow through immobilized Serratia sp cell columns. Chemical and physical characterization of bio-mineralized La and Eu was done by XRD at Birmingham and showed the formation of phosphate minerals. Additional cell column work using S. cerevisiae, B. subtilis, or P. fluorescens, showed that these bacteria are capable of bio-mineralizing Ce(III) and Sm(III). Chemical and physical characterizations of bio-transformed Ce and Sm were analyzed by JAEA, Kyushu U., Tokyo U. Tech. and Kyoto U. using XAFS, SEM and TEM. Results showed that Ce and Sm nanoparticles were formed. The high radiostability of the metal accumulating enzyme of Serratia sp. (which promotes metal phosphate deposition) was shown in whole cells, whereas pure enzyme lost its activity quickly under irradiation. Additional work on radionuclide (Cm) incorporation into Serratia sp calcium phosphate minerals (analogue for human bones) using EXAFS and Time Resolved Laser Fluorescence Spectroscopy (in collaboration with Karlsruhe Institute of Technology) showed that this actinide binds at the grain boundaries between crystallites, which has health implications for human exposure. (author)

Effect of Large Negative Phase of Blast Loading on Structural Response of RC Elements

Directory of Open Access Journals (Sweden)

Syed Zubair Iman

2016-01-01

Full Text Available Structural response of reinforced concrete (RC elements for analysis and design are often obtained using the positive phase of the blast pressure curve disregarding the negative phase assuming insignificant contribution from the negative phase of the loading. Although, some insight on the effect of negative phase of blast pressure based on elastic single-degree-of-freedom (SDOF analysis was presented before, the influence of negative phase on different types of resistance functions of SDOF models and on realistic finite element analysis has not been explored. In this study, the effects of inclusion of pulse negative phase on structural response of RC elements from SDOF analysis and from more detailed finite element analysis have been investigated. Investigation of SDOF part has been conducted using MATLAB code that utilizes non-linear resistance functions of SDOF model. Detailed numerical investigation using finite element code DIANA was conducted on the significance of the negative phase on structural response. In the FE model, different support stiffness was used to explore the effect of support stiffness on the structural response due to blast negative phase. Results from SDOF and FE analyses present specific situations where the effect of large negative phase was found to be significant on the structural response of RC elements.

PETER loop. Multifunctional test facility for thermal hydraulic investigations of PWR fuel elements

International Nuclear Information System (INIS)

Ganzmann, I.; Hille, D.; Staude, U.

2009-01-01

The reliable fuel element behavior during the complete fuel cycle is one of the fundamental prerequisites of a safe and efficient nuclear power plant operation. The fuel element behavior with respect to pressure drop and vibration impact cannot be simulated by means of fluid-structure interaction codes. Therefore it is necessary to perform tests using fuel element mock-ups (1:1). AREVA NP has constructed the test facility PETER (PWR fuel element tests in Erlangen) loop. The modular construction allows maximum flexibility for any type of fuel elements. Modern measuring instrumentation for flow, pressure and vibration characterization allows the analysis of cause and consequences of thermal hydraulic phenomena. PETER loop is the standard test facility for the qualification of dynamic fuel element behavior in flowing fluid and is used for failure mode analysis.

Investigation of Forming Performance of Laminated Steel Sheets Using Finite Element Analyses

International Nuclear Information System (INIS)

Liu Wenning; Sun Xin; Ruokolainen, Robert; Gayden Xiaohong

2007-01-01

Laminated steel sheets have been used in automotive structures for reducing in-cabin noise. However, due to the marked difference in material properties of the different laminated layers, integrating laminated steel parts into the manufacturing processes can be challenging. Especially, the behavior of laminated sheets during forming processes is very different from that of monolithic steel sheets. During the deep-draw forming process, large shear deformation and corresponding high interfacial stress may initiate and propagate interfacial cracks between the core polymer and the metal skin, hence degrading the performance of the laminated sheets. In this paper, the formability of the laminated steel sheets is investigated by means of numerical analysis. The goal of this work is to gain insight into the relationship between the individual properties of the laminated sheet layers and the corresponding formability of the laminated sheet as a whole, eventually leading to reliable design and successful forming process development of such materials. Finite element analyses of laminate sheet forming are presented. Effects of polymer core thickness and viscoelastic properties of the polymer core, as well as punching velocity, are also investigated

A combined wet/dry sipping cell for investigating failed triga fuel elements

International Nuclear Information System (INIS)

Boeck, H.; Gallhammer, H.; Hammer, J.; Israr, M.

1987-08-01

A sipping cell to detect failed triga fuel has been designed and constructed at the Atominstitut. The cell allows both wet- and dry sipping of one single standard triga fuel element. In the dry sipping method the fuel element may be electrically heated up to a maximum temperature of about 300 0 C to allow the detection of temperature dependent fission product release from the fuel element. 20 figs., 1 tab. (Author)

Investigation of the Behavior of Steel Shear Walls Using Finite Elements Analysis

OpenAIRE

Abubakri, K.; Veladi, H.

2016-01-01

Currently, steel shear walls are considered by engineers as an economic method against lateral loads imposed by wind and earthquake in tall structures. Accordingly, there is a growing need to develop accurate methods alongside approximation methods to estimate the behavior of these structural elements. The finite element technique is one of the strongest numerical methods in analysis of solid mechanics problems. Finite element analysis however requires high technical knowledge of the behavior...

Investigations on the direct introduction of cigarette smoke for trace elements analysis by inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Chang, Michael J.; Naworal, John D.; Walker, Kathleen; Connell, Chris T.

2003-01-01

Direct introduction of mainstream cigarette smoke into an inductively coupled plasma mass spectrometry (ICP-MS) has been investigated with respect to its feasibility for on-line analysis of trace elements. An automated apparatus was designed and built interfacing a smoking machine with an ICP-MS for smoke generation, collection, injection and analysis. Major and minor elements present in the particulate phase and the gas phase of mainstream cigarette smoke of 2R4F reference cigarettes have been qualitatively identified by examination of their full mass spectra. This method provides a rapid-screening analysis of the transfer of trace elements into mainstream smoke during cigarette combustion. A full suite of elements present in the whole cigarette smoke has been identified, including As, B, Ba, Br, Cd, Cl, Cs, Cu, Hg, I, K, Li, Mn, Na, Pb, Rb, Sb, Sn, Tl and Zn. Of these elements, the major portions of B, Ba, Cs, Cu, K, Li, Mn, Na, Pb, Rb, Sn, Tl and Zn are present in the particulate phase, whereas the major portion of Hg is present in the gas phase. As, Br, Cd, Cl, I and Sb exist in a distribution between the gas phase and the particulate phase. Depending on the element, the precision of measurement ranges from 5 to 25% in terms of relative standard deviation of peak height and peak area, based on the fourth puff of 2R4F mainstream cigarette smoke analyzed in five smoking replicates

A four-element based transposon system for allele specific tagging ...

Indian Academy of Sciences (India)

The four-element based construct would include both Ds and dSpm along with relevant marker genes and .... subsequent generations after transposition has taken place so as to ..... Cardon G H, Frey M, Seadler H and Gierl A 1993 Definition.

Behaviour of radioactive elements in the vegetation of uranium mine

International Nuclear Information System (INIS)

Shitaka, Yukinori

2001-03-01

To improve the predictability of radium transfer from soil to plant, the behaviour was compared with other alkaline earth elements. I analyzed the radium transfer ratio as the factor of solubility from soil to water, absorbability by plant from soil, and the allocation to each organ for three grass fields in Ningyo-Toge environmental engineering center. The results indicated that the behaviour of radium is correlated with that of other alkaline earth elements. Moreover negative correlation was found between the absorbability of each element and the concentration of Mg and/or Ca in soluble fraction. From the results, it was suggested that the absorption of radium should be influenced by the regulation of the absorption of these nutrients. Secondly, to clarify the soil- and plant-specific feature of the radium transfer, the radium transfer was investigated for twelve plant species from four vegetation. There was 60 times of difference in radium concentration among plant species. It was observed that there is strong correlation between the transfer factor of radium and that of calcium. The differences in radium concentration of plant were explained by the soil-specific difference in the concentration ratio of radium and the plant-specific difference in calcium concentration. (author)

Chemical experiments with superheavy elements.

Science.gov (United States)

Türler, Andreas

2010-01-01

Unnoticed by many chemists, the Periodic Table of the Elements has been extended significantly in the last couple of years and the 7th period has very recently been completed with eka-Rn (element 118) currently being the heaviest element whose synthesis has been reported. These 'superheavy' elements (also called transactinides with atomic number > or = 104 (Rf)) have been artificially synthesized in fusion reactions at accelerators in minute quantities of a few single atoms. In addition, all isotopes of the transactinide elements are radioactive and decay with rather short half-lives. Nevertheless, it has been possible in some cases to investigate experimentally chemical properties of transactinide elements and even synthesize simple compounds. The experimental investigation of superheavy elements is especially intriguing, since theoretical calculations predict significant deviations from periodic trends due to the influence of strong relativistic effects. In this contribution first experiments with hassium (Hs, atomic number 108), copernicium (Cn, atomic number 112) and element 114 (eka-Pb) are reviewed.

Soil-to-plant transfer of elements is not linear: Results for five elements relevant to radioactive waste in five boreal forest species

Energy Technology Data Exchange (ETDEWEB)

Tuovinen, Tiina S.; Roivainen, Paeivi, E-mail: paivi.roivainen@uef.fi; Makkonen, Sari; Kolehmainen, Mikko; Holopainen, Toini; Juutilainen, Jukka

2011-12-01

Element-specific concentration ratios (CRs) assuming that plant uptake of elements is linear are commonly used in radioecological modelling to describe the soil-to-plant transfer of elements. The goal of this study was to investigate the validity of the linearity assumption in boreal forest plants, for which only limited relevant data are available. The soil-to-plant transfer of three essential (Mo, Ni, Zn) and two non-essential (Pb, U) elements relevant to the safety of radioactive waste disposal was studied. Three understory species (blueberry, narrow buckler fern and May lily) and two tree species (Norway spruce and rowan) were included. Examining CRs as a function of soil concentration showed that CR was not constant but decreased with increasing soil concentrations for all elements and plant species. A non-linear equation fitted fairly well with the empirical data; the R{sup 2}-values for this equation were constantly higher than those for the linear fit. The difference between the two fits was most evident at low soil concentrations where the use of constant CRs underestimated transfer from soil to plants. Site-specific factors affected the transfer of Mo and Ni. The results suggested that systematic variation with soil concentrations explains a part of the large variation of empirically determined CRs, and the accuracy of modelling the soil-to-plant transfer might be improved by using non-linear methods. Non-linearity of soil-to-plant transfer has been previously reported for a few different species, elements and environments. The present study systematically tested the linearity assumption for five elements (both essential and non-essential) and in five boreal forest species representing different growth traits and phylogenies. The data supported non-linearity in all cases.

Soil-to-plant transfer of elements is not linear: Results for five elements relevant to radioactive waste in five boreal forest species

International Nuclear Information System (INIS)

Tuovinen, Tiina S.; Roivainen, Päivi; Makkonen, Sari; Kolehmainen, Mikko; Holopainen, Toini; Juutilainen, Jukka

2011-01-01

Element-specific concentration ratios (CRs) assuming that plant uptake of elements is linear are commonly used in radioecological modelling to describe the soil-to-plant transfer of elements. The goal of this study was to investigate the validity of the linearity assumption in boreal forest plants, for which only limited relevant data are available. The soil-to-plant transfer of three essential (Mo, Ni, Zn) and two non-essential (Pb, U) elements relevant to the safety of radioactive waste disposal was studied. Three understory species (blueberry, narrow buckler fern and May lily) and two tree species (Norway spruce and rowan) were included. Examining CRs as a function of soil concentration showed that CR was not constant but decreased with increasing soil concentrations for all elements and plant species. A non-linear equation fitted fairly well with the empirical data; the R 2 -values for this equation were constantly higher than those for the linear fit. The difference between the two fits was most evident at low soil concentrations where the use of constant CRs underestimated transfer from soil to plants. Site-specific factors affected the transfer of Mo and Ni. The results suggested that systematic variation with soil concentrations explains a part of the large variation of empirically determined CRs, and the accuracy of modelling the soil-to-plant transfer might be improved by using non-linear methods. Non-linearity of soil-to-plant transfer has been previously reported for a few different species, elements and environments. The present study systematically tested the linearity assumption for five elements (both essential and non-essential) and in five boreal forest species representing different growth traits and phylogenies. The data supported non-linearity in all cases.

Toxicologically important trace elements and organic compounds investigated in size-fractionated urban particulate matter collected near the Prague highway

International Nuclear Information System (INIS)

Sysalová, Jiřina; Sýkorová, Ivana; Havelcová, Martina; Száková, Jiřina; Trejtnarová, Hana; Kotlík, Bohumil

2012-01-01

Urban particulate matter was collected in the most exposed area of Prague, near a busy highway, in order to provide petrographic and chemical characterization useful for health impact assessment in that locality or other applications. Samples were collected from filters of the air conditioning system in two years, 2009 and 2010, and sieved into four grain-size fractions: 0.507–0.119 mm, 0.119–0.063 mm, 3 extracted solutions. A composition of inorganic and carbonaceous particles of natural and anthropogenic origin and their morphology were studied by optical and electron microscopy. Organic solvent extracts of the samples were analyzed using gas chromatography to compare the organic compound distribution in fractions. Only slight differences between 2009 and 2010 years are visible. The relatively high extractable part of most investigated elements confirms mobility and potential availability to organisms. The changes can be recognized in the petrographic and organic composition in samples from both years, which were likely the result of various inputs of source materials. Specific organic marker compounds indicate contribution from fossil fuels, plant materials and bacteria. -- Highlights: ► Uncommon urban particulate matter collected near the highway in years 2009 and 2010 was deeply characterized. ► Harmful organic compounds and toxic analytes were tested in grain-size fractions and completed with electron microscopy studies. ► Very similar concentration levels were found in elemental composition in samples from two years. ► Petrographic and organic compositions were different in both samples. ► Relatively high mobility of selected analytes was found in 2M HNO 3 extracted solutions.

Some investigation on trace elements content of Iranian breads using neutron activation analysis and atomic absorption spectroscopy

International Nuclear Information System (INIS)

Gharib, A.; Fatemi, K.; Moazezi, A.; Mahmoodzadeh, A.; Koushkestani, R.

1988-01-01

Since bread is consumed as a principal dietary staple by the majority of Iranian communities, actual natural portion of required protein and energy are provided via bread. Therefore, with respect to this matter, a considerable amount of needed minerals must also be met through this way. Literature survey indicates some elemental deficiencies as the result of consumption of bread in Iran. On the other hand, essentiality of these elements to human which are mostly in the range of trace amounts, makes this investigation very much important and interesting from both sides, nutritionally and instrumentally. To meet the above requirements, applications of very sensitive analytical tools are unavoidable. Hence, atomic absorption spectroscopy and neutron activation analysis both RNAA and INAA are employed. Results are controversial and constructive

Toxicologically important trace elements and organic compounds investigated in size-fractionated urban particulate matter collected near the Prague highway.

Science.gov (United States)

Sysalová, Jiřina; Sýkorová, Ivana; Havelcová, Martina; Száková, Jiřina; Trejtnarová, Hana; Kotlík, Bohumil

2012-10-15

Urban particulate matter was collected in the most exposed area of Prague, near a busy highway, in order to provide petrographic and chemical characterization useful for health impact assessment in that locality or other applications. Samples were collected from filters of the air conditioning system in two years, 2009 and 2010, and sieved into four grain-size fractions: 0.507-0.119 mm, 0.119-0.063 mm, origin and their morphology were studied by optical and electron microscopy. Organic solvent extracts of the samples were analyzed using gas chromatography to compare the organic compound distribution in fractions. Only slight differences between 2009 and 2010 years are visible. The relatively high extractable part of most investigated elements confirms mobility and potential availability to organisms. The changes can be recognized in the petrographic and organic composition in samples from both years, which were likely the result of various inputs of source materials. Specific organic marker compounds indicate contribution from fossil fuels, plant materials and bacteria. Copyright © 2012 Elsevier B.V. All rights reserved.

Finite element analysis of inclined nozzle-plate junctions

International Nuclear Information System (INIS)

Dixit, K.B.; Seth, V.K.; Krishnan, A.; Ramamurthy, T.S.; Dattaguru, B.; Rao, A.K.

1979-01-01

Estimation of stress concentration at nozzle to plate or shell junctions is a significant problem in the stress analysis of nuclear reactors. The topic is a subject matter of extensive investigations and earlier considerable success has been reported on analysis for the cases when the nozzle is perpendicular to the plate or is radial to the shell. Analytical methods for the estimation of stress concentrations for the practical situations when the intersecting nozzle is inclined to the plate or is non-radial to the shell is rather scanty. Specific complications arise in dealing with the junction region when the nozzle with circular cross-section meets the non-circular cut-out on the plate or shell. In this paper a finite element analysis is developed for inclined nozzles and results are presented for nozzle-plate junctions. A method of analysis is developed with a view to achieving simultaneously accuracy of results and simplicity in the choice of elements and their connectivity. The circular nozzle is treated by axisymmetric conical shell elements. The nozzle portion in the region around the junction and the flat plate is dealt with by triangular flat shell elements. Special transition elements are developed for joining the flat shell elements with the axisymmetric elements under non-axisymmetric loading. A substructure method of analysis is adopted which achieves considerable economy in handling the structure and also conveniently combines the different types of elements in the structure. (orig.)

Investigating the Role of Interventricular Interdependence in Development of Right Heart Dysfunction During LVAD Support: A Patient-Specific Methods-Based Approach

Directory of Open Access Journals (Sweden)

Kevin L. Sack

2018-05-01

Full Text Available Predictive computation models offer the potential to uncover the mechanisms of treatments whose actions cannot be easily determined by experimental or imaging techniques. This is particularly relevant for investigating left ventricular mechanical assistance, a therapy for end-stage heart failure, which is increasingly used as more than just a bridge-to-transplant therapy. The high incidence of right ventricular failure following left ventricular assistance reflects an undesired consequence of treatment, which has been hypothesized to be related to the mechanical interdependence between the two ventricles. To investigate the implication of this interdependence specifically in the setting of left ventricular assistance device (LVAD support, we introduce a patient-specific finite-element model of dilated chronic heart failure. The model geometry and material parameters were calibrated using patient-specific clinical data, producing a mechanical surrogate of the failing in vivo heart that models its dynamic strain and stress throughout the cardiac cycle. The model of the heart was coupled to lumped-parameter circulatory systems to simulate realistic ventricular loading conditions. Finally, the impact of ventricular assistance was investigated by incorporating a pump with pressure-flow characteristics of an LVAD (HeartMate II™ operating between 8 and 12 k RPM in parallel to the left ventricle. This allowed us to investigate the mechanical impact of acute left ventricular assistance at multiple operating-speeds on right ventricular mechanics and septal wall motion. Our findings show that left ventricular assistance reduces myofiber stress in the left ventricle and, to a lesser extent, right ventricle free wall, while increasing leftward septal-shift with increased operating-speeds. These effects were achieved with secondary, potentially negative effects on the interventricular septum which showed that support from LVADs, introduces unnatural bending

Investigation of the solution properties of the transuranium elements. Final report, July 1, 1979-September 30, 1984

International Nuclear Information System (INIS)

Ensor, D.D.

1984-01-01

This final report summarizes the significant results obtained during our investigation of the fundamental solution properties of the transuranium elements for the period July 1, 1979 to September 30, 1984. Primary interest of the project was the development of improved separation methods for the trivalent actinide elements from each other and from the chemically similar trivalent lanthanide elements using solvent extraction techniques. Two different synergistic systems were investigated. The combination of dialkynaphthalenesulfonic acids with a crown ether or an oxime was an attempt to combine the excellent ion exchange properties of the sulfonic extractant with a synergistic agent which would improve the selectivity of the extraction system. The results showed that the presence of the crown ether improved the extraction of the light lanthanides by approximately 50% while the heavy lanthanides were unaffected. The use of the oxime in combination with the sulfonic acid extractant showed significant enhancement for all metal ions studied but little, if any, selectivity. The use of novel oxygen donors as synergistic agents in combination with thenoyltrifluoroacetone provided significant enhancement for the extraction of trivalent lanthanides and actinides. The data showed the best selectivity was obtained using a linear polyether as the synergistic agent. The crown ether and the cryptand showed significant synergistic capabilities but lacked selectivity due to their rigid cavities. The results of this study indicate that the linear polyether is more promising as a synergistic agent because of its flexibility and ease of chemical modification of the end groups. 10 figures, 5 tables

Compilation of Cooperative Data Element Dictionary of Five Federal Agencies’ Systems for Processing of Technical Report Literature

Science.gov (United States)

1983-03-01

investigator participated with Libary of Congress (LC) Staff and Gov- ernment Printing Office (GPO) catalogers in identifying which data elements...National Standards Institute Standard format, ANSI Z.39-2). This standard includes iden- tif ication of specific data elements by means of 3- digit tags...the closer they can come to efficient exchange. But tags assigned to the core data elements differ: they are all 3- digit tags, but the same 3 digits

Mapping 3D breast lesions from full-field digital mammograms using subject-specific finite element models

Science.gov (United States)

García, E.; Oliver, A.; Diaz, O.; Diez, Y.; Gubern-Mérida, A.; Martí, R.; Martí, J.

2017-03-01

Patient-specific finite element (FE) models of the breast have received increasing attention due to the potential capability of fusing images from different modalities. During the Magnetic Resonance Imaging (MRI) to X-ray mammography registration procedure, the FE model is compressed mimicking the mammographic acquisition. Subsequently, suspicious lesions in the MRI volume can be projected into the 2D mammographic space. However, most registration algorithms do not provide the reverse information, avoiding to obtain the 3D geometrical information from the lesions localized in the mammograms. In this work we introduce a fast method to localize the 3D position of the lesion within the MRI, using both cranio-caudal (CC) and medio-lateral oblique (MLO) mammographic projections, indexing the tetrahedral elements of the biomechanical model by means of an uniform grid. For each marked lesion in the Full-Field Digital Mammogram (FFDM), the X-ray path from source to the marker is calculated. Barycentric coordinates are computed in the tetrahedrons traversed by the ray. The list of elements and coordinates allows to localize two curves within the MRI and the closest point between both curves is taken as the 3D position of the lesion. The registration errors obtained in the mammographic space are 9.89 +/- 3.72 mm in CC- and 8.04 +/- 4.68 mm in MLO-projection and the error in the 3D MRI space is equal to 10.29 +/- 3.99 mm. Regarding the uniform grid, it is computed spending between 0.1 and 0.7 seconds. The average time spent to compute the 3D location of a lesion is about 8 ms.

NUMERICAL INVESTIGATION OF TWO ELEMENT CAMBER MORPHING AIRFOIL IN LOW REYNOLDS NUMBER FLOWS

Directory of Open Access Journals (Sweden)

RAJESH SENTHIL KUMAR T.

2017-07-01

Full Text Available Aerodynamic performance of a two-element camber morphing airfoil was investigated at low Reynolds number using the transient SST model in ANSYS FLUENT 14.0 and eN method in XFLR5. The two-element camber morphing concept was employed to morph the baseline airfoil into another airfoil by altering the orientation of mean-line at 35% of the chord to achieve better aerodynamic efficiency. NACA 0012 was selected as baseline airfoil. NACA 23012 was chosen as the test case as it has the camber-line similar to that of the morphed airfoil and as it has the same thickness as that of the baseline airfoil. The simulations were carried out at chord based Reynolds numbers of 2.5×105 and 3.9×105. The aerodynamic force coefficients, aerodynamic efficiency and the location of the transition point of laminar separation bubble over these airfoils were studied for various angles of attack. It was found that the aerodynamic efficiency of the morphed airfoil was 12% higher than that of the target airfoil at 4° angle of attack for Reynolds number of 3.9×105 and 54% rise in aerodynamic performance was noted as Reynolds number was varied from 2.5×105 to 3.9×105. The morphed airfoil exhibited the nature of low Reynolds number airfoil.

Remedial Investigation/Feasibility Study (RI/FS) process, elements and techniques guidance

Energy Technology Data Exchange (ETDEWEB)

1993-12-01

This manual provides detailed guidance on Remedial Investigation/Feasibility Studies (RI/FSs) conducted pursuant to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) at Department of Energy (DOE) facilities. The purpose of the RI/FS, to assess the risk posed by a hazardous waste site and to determine the best way to reduce that risk, and its structure (site characterization, risk assessment, screening and detailed analysis of alternatives, etc.) is defined in the National Oil and Hazardous Substances Pollution Contingency Plan (NCP) and further explained in the Environmental Protection Agency`s (EPA`s) Guidance for Conducting Remedial Investigations and Feasibility Studies Under CERCLA (Interim Final) 540/G-89/004, OSWER Directive 9355.3-01, October 1988. Though issued in 1988, the EPA guidance remains an excellent source of information on the conduct and structure of an RI/FS. This document makes use of supplemental RI/FS-related guidance that EPA has developed since its initial document was issued in 1988, incorporates practical lessons learned in more than 12 years of experience in CERCLA hazardous site remediation, and drawing on those lessons, introduces the Streamlined Approach For Environmental Restoration (SAFER), developed by DOE as a way to proceed quickly and efficiently through the RI/FS process at DOE facilities. Thus as its title implies, this guidance is intended to describe in detail the process and component elements of an RI/FS, as well as techniques to manage the RI/FS effectively.

Computer simulation of fuel element performance

Energy Technology Data Exchange (ETDEWEB)

Sukhanov, G I

1979-01-01

The review presents reports made at the Conference on the Bahaviour and Production of Fuel for Water Reactors on March 13-17, 1979. Discussed at the Conference are the most developed and tested calculation models specially evolved to predict the behaviour of fuel elements of water reactors. The following five main aspects of the problem are discussed: general conceptions and programs; mechanical mock-ups and their applications; gas release, gap conductivity and fuel thermal conductivity; analysis of nonstationary processes; models of specific phenomena. The review briefly describes the physical principles of the following models and programs: the RESTR, providing calculation of the radii of zones of columnar and equiaxial grains as well as the radius of the internal cavity of the fuel core; programs for calculation of fuel-can interaction, based on the finite elements method; a model predicting the behaviour of the CANDU-PHW fuel elements in transient conditions. General results are presented of investigations of heat transfer through a can-fuel gap and thermal conductivity of UO/sub 2/ with regard for cracking and gas release of the fuel. Many programs already suit the accepted standards and are intensively tested at present.

Experimental Investigation of Zinc Antimonide Thin Film Thermoelectric Element over Wide Range of Operating Conditions

DEFF Research Database (Denmark)

Mirhosseini, Mojtaba; Rezania, Alireza; Blichfeld, Anders B.

2017-01-01

flows in plane with the thin film. At first, the effect of applying different temperatures at the hot side of the specimen is investigated to reach steady state in an open circuit analysis. Then, the study focuses on performance and stability analysis of the thermoelectric element operating under......Zinc antimonide compounds are among the most efficient thermoelectric (TE) materials with exceptional low thermal conductivity at moderate temperatures up to 350 °C. This study aims to evaluate the performance of a zinc antimonide thin film TE deposited on an insulating substrate, while the heat...

FUDA MOD-2: a computer program for simulation the performance of fuel element validation exercise

International Nuclear Information System (INIS)

Chouhan, S.K.; Tripathi, R.M.; Prasad, P.N.; Chauhan, Ashok

2014-01-01

The PHWR fuel element performance is evaluated using the fuel analysis computer code FUDA MOD2. It is specifically written for performance simulation of UO 2 fuel pellet, located in zirconium alloy sheath operating under coolant pressure. For specific element power histories, the code investigates the variables and their interactions that govern fuel element performance. The input data requires pellet dimensions, element dimensions, sheath properties, heat transfer data, thermal hydraulic parameters of coolant, the inner filler gas composition, flux gradient and linear heat ratings (LHR) at different burn up. The output data generated by the code are radial temperature profile of fuel and sheath, fuel sheath-gap heat transfer coefficient, fission gas generated and released, fission gas pressure, sheath stress and strain for different burn-up zones. The code has been verified against literature data and post irradiation examinations carried out. It is also bench marked against various international fuel element simulation programmes available with water cooled reactors operating countries. The present paper describes the FUDA MOD2 code verification studies carried out using the literature data and post irradiation examination data. (author)

Chemistry of superheavy elements

International Nuclear Information System (INIS)

Schaedel, M.

2012-01-01

The chemistry of superheavy elements - or transactinides from their position in the Periodic Table - is summarized. After giving an overview over historical developments, nuclear aspects about synthesis of neutron-rich isotopes of these elements, produced in hot-fusion reactions, and their nuclear decay properties are briefly mentioned. Specific requirements to cope with the one-atom-at-a-time situation in automated chemical separations and recent developments in aqueous-phase and gas-phase chemistry are presented. Exciting, current developments, first applications, and future prospects of chemical separations behind physical recoil separators ('pre-separator') are discussed in detail. The status of our current knowledge about the chemistry of rutherfordium (Rf, element 104), dubnium (Db, element 105), seaborgium (Sg, element 106), bohrium (Bh, element 107), hassium (Hs, element 108), copernicium (Cn, element 112), and element 114 is discussed from an experimental point of view. Recent results are emphasized and compared with empirical extrapolations and with fully-relativistic theoretical calculations, especially also under the aspect of the architecture of the Periodic Table. (orig.)

The elements Se, Hg, Cr, Sb, Fe, Zn, Co, and Rb were investigated by neutron activation analysis in blood serum of leukemia patients and workers of metal coating industries

International Nuclear Information System (INIS)

Taheriean, Ali Akbar.

1992-02-01

Current universal interests in trace element studies are being spurred by our needs to determine trace element requirements and tolerance by organism, including relationships to animal and human health and disease, evaluate the potential bio magnification and bio toxicity of trace elements. The element Se, Hg, Cr, Sb, Fe, Zn, Co, and Rb were investigated in blood serum of 24 leukemia patients and 20 workers of metal coating of industries, using neutron activation analysis and gamma ray counting high purity germanium detector, it was possible to determine the above mentioned trace elements with great accuracy. The result of these investigations are described briefly. In the blood serum of leukemia patients, which were collected from Ali Asghar children Hospital, some increase of Fe and decrease of Se could be found, whereas the amount variation of other trace elements were negligible. The amount of Zn in the blood serum of these workers by comparison with 60 normal man indicates no change. Due to importance of trace elements in the human health we suggest that this investigation must be prolonged using more samples

Multi-element probabilistic collocation method in high dimensions

International Nuclear Information System (INIS)

Foo, Jasmine; Karniadakis, George Em

2010-01-01

We combine multi-element polynomial chaos with analysis of variance (ANOVA) functional decomposition to enhance the convergence rate of polynomial chaos in high dimensions and in problems with low stochastic regularity. Specifically, we employ the multi-element probabilistic collocation method MEPCM and so we refer to the new method as MEPCM-A. We investigate the dependence of the convergence of MEPCM-A on two decomposition parameters, the polynomial order μ and the effective dimension ν, with ν<< N, and N the nominal dimension. Numerical tests for multi-dimensional integration and for stochastic elliptic problems suggest that ν≥μ for monotonic convergence of the method. We also employ MEPCM-A to obtain error bars for the piezometric head at the Hanford nuclear waste site under stochastic hydraulic conductivity conditions. Finally, we compare the cost of MEPCM-A against Monte Carlo in several hundred dimensions, and we find MEPCM-A to be more efficient for up to 600 dimensions for a specific multi-dimensional integration problem involving a discontinuous function.

Analytical and experimental investigation on a multiple-mass-element pendulum impact damper for vibration mitigation

Science.gov (United States)

Egger, Philipp; Caracoglia, Luca

2015-09-01

Impact dampers are often used in the field of civil, mechanical and aerospace engineering for reducing structural vibrations. The behavior of this type of passive control device has been investigated for several decades. In this research a distributed-mass impact damper, similar to the "chain damper" used in wind engineering, has been examined and applied to the vibration reduction on a slender line-like structural element (stay-cable). This study is motivated by a practical problem and describes the derivation of a reduced-order model for explaining the behavior, observed during a field experiment on a prototype system. In its simplest form, the dynamics of the apparatus is modeled as a "resilient damper", composed of mass-spring-dashpot secondary elements, attached to the primary structure. Various sources of excitation are analyzed: free vibration, external harmonic force and random excitation. The proposed model is general and potentially applicable to the analysis of several structural systems. The study also shows that the model can adequately describe and explain the experimentally observed behavior.

Investigation of Pre-Service Teachers' Opinions about Science in Terms of the Basic Elements of the Education Program

Science.gov (United States)

Sengul, Ozge Aydin

2016-01-01

The purpose of the current study is to investigate the pre-service teachers' opinions about science within the context of the basic elements of the education program, such as objectives, content, learning-teaching process and evaluation. The study was designed as a case study, one of the qualitative research methods. The participants of the study…

Birth outcomes and background exposures to select elements, the Longitudinal Investigation of Fertility and the Environment (LIFE).

Science.gov (United States)

Bloom, Michael S; Buck Louis, Germaine M; Sundaram, Rajeshwari; Maisog, Jose M; Steuerwald, Amy J; Parsons, Patrick J

2015-04-01

Evidence suggests that trace exposures to select elements may increase the risk for adverse birth outcomes. To investigate further, we used multiple regression to assess associations between preconception parental exposures to Pb, Cd, and total Hg in blood, and 21 elements in urine, with n=235 singleton birth outcomes, adjusted for confounders and partner's exposure. Earlier gestational age at delivery (GA) was associated with higher tertiles of urine maternal W (-1.22 days) and paternal U (-1.07 days), but GA was later for higher tertiles of maternal (+1.11 days) and paternal (+1.30 days) blood Hg. Additional analysis indicated shorter GA associated with higher paternal urine Ba, W, and U, and with higher maternal blood Pb for boys, but GA was longer in association with higher maternal urine Cr. Birth weight (BW) was lower for higher tertiles of paternal urine Cs (-237.85g), U (-187.34g), and Zn (-209.08g), and for higher continuous Cr (P=0.021). In contrast, BW was higher for higher tertiles of paternal urine As (+194.71g) and counterintuitively for maternal blood Cd (+178.52g). Birth length (BL) was shorter for higher tertiles of urine maternal W (-1.22cm) and paternal U (-1.10cm). Yet, higher tertiles of maternal (+1.11cm) and paternal (+1.30) blood Hg were associated with longer BL. Head circumference at delivery was lower for higher tertiles of paternal urine U (-0.83cm), and for higher continuous Mo in boys (-0.57cm). Overall, associations were most consistently indicated for GA and measures of birth size with urine W and U, and paternal exposures were more frequently associated than maternal. Though limited by several factors, ours is the largest multi-element investigation of prospective couple-level trace exposures and birth outcomes to date; the novel observations for W and U merit further investigation. Copyright © 2015 Elsevier Inc. All rights reserved.

Magnetic dichroism in photoemission: a new element-specific magnetometer with atomic-layer resolution

International Nuclear Information System (INIS)

Starke, K.; Arenholz, E.; Kaindl, G.

1998-01-01

Full text: Magnetic coupling in layered metallic structures has become a key issue in thin-film magnetism since the observation of oscillatory exchange coupling across non-ferromagnetic spacer layers. Although this phenomenon was discovered in rare earths (RE) superlattices, mostly transition-metal systems have been studied and are now applied in data-storage industry. An understanding of the coupling mechanisms has been reached after a fabrication of high-quality interfaces became possible. It allowed, in particular, the experimental finding of induced ferromagnetic order in 'nonmagnetic' atomic layers near an interface, using element-specific probes such as magnetic circular dichroism in x-ray absorption. - In layered RE systems, by contrast, the well known intermiscibility has prevented a preparation of atomically sharp interfaces, and all RE superlattices studied so far showed interdiffusion zones of several atomic layers. In the present overview, we report the first fabrication of atomically flat heteromagnetic RE interfaces, their structural characterization and their magnetic analysis using magnetic dichroism in photoemission (MDPE). This new tool gives access to the magnetization of individual atomic layers near interfaces in favourite cases. Merits of MDPE as a magnetometer are demonstrated at the example of Eu/Gd(0001), where chemical shifts of core-level photoemission lines allow to spectroscopically separate up to four different atomic layers. The high surface sensitivity of MDPE, together with the well known dependence of the core-level binding energies on the coordination number of the photo emitting atom, opens the door to future site-specific studies of magnetism in sub-monolayer systems such as 'nanowires'

Investigation of dissipation elements in a fully developed turbulent channel flow by tomographic particle-image velocimetry

Science.gov (United States)

Schäfer, L.; Dierksheide, U.; Klaas, M.; Schröder, W.

2011-03-01

A new method to describe statistical information from passive scalar fields has been proposed by Wang and Peters ["The length-scale distribution function of the distance between extremal points in passive scalar turbulence," J. Fluid Mech. 554, 457 (2006)]. They used direct numerical simulations (DNS) of homogeneous shear flow to introduce the innovative concept. This novel method determines the local minimum and maximum points of the fluctuating scalar field via gradient trajectories, starting from every grid point in the direction of the steepest ascending and descending scalar gradients. Relying on gradient trajectories, a dissipation element is defined as the region of all the grid points, the trajectories of which share the same pair of maximum and minimum points. The procedure has also been successfully applied to various DNS fields of homogeneous shear turbulence using the three velocity components and the kinetic energy as scalar fields [L. Wang and N. Peters, "Length-scale distribution functions and conditional means for various fields in turbulence," J. Fluid Mech. 608, 113 (2008)]. In this spirit, dissipation elements are, for the first time, determined from experimental data of a fully developed turbulent channel flow. The dissipation elements are deduced from the gradients of the instantaneous fluctuation of the three velocity components u', v', and w' and the instantaneous kinetic energy k', respectively. The measurements are conducted at a Reynolds number of 1.7×104 based on the channel half-height δ and the bulk velocity U. The required three-dimensional velocity data are obtained investigating a 17.75×17.75×6 mm3 (0.355δ×0.355δ×0.12δ) test volume using tomographic particle-image velocimetry. Detection and analysis of dissipation elements from the experimental velocity data are discussed in detail. The statistical results are compared to the DNS data from Wang and Peters ["The length-scale distribution function of the distance between

High resolution quantitative element mapping of neuromelanin-containing neurons

Energy Technology Data Exchange (ETDEWEB)

Reinert, Tilo [Nukleare Festkoerperphysik, Universitaet Leipzig, Linnestrasse 5, 04103 Leipzig (Germany)]. E-mail: reinert@physik.uni-leipzig.de; Fiedler, Anja [Nukleare Festkoerperphysik, Universitaet Leipzig, Linnestrasse 5, 04103 Leipzig (Germany); Paul-Flechsig-Institut fuer Hirnforschung, Universitaet Leipzig, Jahnallee 59, 04109 Leipzig (Germany); Morawski, Markus [Paul-Flechsig-Institut fuer Hirnforschung, Universitaet Leipzig, Jahnallee 59, 04109 Leipzig (Germany); Arendt, Thomas [Paul-Flechsig-Institut fuer Hirnforschung, Universitaet Leipzig, Jahnallee 59, 04109 Leipzig (Germany)

2007-07-15

Neuromelanin is a dark coloured intracellular pigment that appears in a specific population of neurons (dopaminergic and noradrenergic) predominantly in the substantia nigra and in the locus coeruleus. In recent years, there is increasing interest in the role of neuromelanin because of a hypothesised link between this pigment and the cell death of neuromelanin-containing neurons in Parkinson's disease (PD). Therefore, the role of neuromelanin in the pathology of PD is an actual focus in neuroscience. We have investigated the elemental contents and distributions of sulphur, calcium, iron, nickel and copper of neuromelanin in dopaminergic neurons for a Parkinson case and a control case (in situ, 6 {mu}m brain sections). There was no difference in the iron concentration between the two cases. However, the calcium concentration was 3-fold higher in the Parkinson case, whereas the copper and nickel concentrations decreased. An ultrastructural investigation of the concentrations of calcium and iron within the neuromelanin suggests that these two elements are not necessarily co-localized.

A 3.0-kb deletion including an erythroid cell-specific regulatory element in intron 1 of the ABO blood group gene in an individual with the Bm phenotype.

Science.gov (United States)

Sano, R; Kuboya, E; Nakajima, T; Takahashi, Y; Takahashi, K; Kubo, R; Kominato, Y; Takeshita, H; Yamao, H; Kishida, T; Isa, K; Ogasawara, K; Uchikawa, M

2015-04-01

We developed a sequence-specific primer PCR (SSP-PCR) for detection of a 5.8-kb deletion (B(m) 5.8) involving an erythroid cell-specific regulatory element in intron 1 of the ABO blood group gene. Using this SSP-PCR, we performed genetic analysis of 382 individuals with Bm or ABm. The 5.8-kb deletion was found in 380 individuals, and disruption of the GATA motif in the regulatory element was found in one individual. Furthermore, a novel 3.0-kb deletion involving the element (B(m) 3.0) was demonstrated in the remaining individual. Comparisons of single-nucleotide polymorphisms and microsatellites in intron 1 between B(m) 5.8 and B(m) 3.0 suggested that these deletions occurred independently. © 2014 International Society of Blood Transfusion.

Chemistry of the actinide elements. Second edition

International Nuclear Information System (INIS)

Katz, J.J.; Seaborg, G.T.; Morss, L.R.

1987-01-01

This is an exhaustive, updated discourse on the chemistry of Actinides, Volume 1 contains a systematic coverage of the elements Ac, Th, Pa, U, Np, and Pu, which constitutes Part 1 of the work. The characterization of each element is discussed in terms of its nuclear properties, occurrence, preparation, atomic and metallic properties, chemistry of specific compounds, and solution chemistry. The first part of Volume 2 follows the same format as Volume 1 but is confined to the elements Am, Cm, Bk, Cf, and Es, plus a more condensed coverage of the Transeinsteinium elements (Fm, Md, No, Lw, and 104-109). Part 2 of this volume is devoted to a discussion of the actinide elements in general, with a specific focus on electronic spectra, thermodynamic and magnetic properties, the metallic state, structural chemistry, solution kinetics, organometallic chemistry for σ- and π-bonded compounds, and some concluding remarks on the superheavy elements

Investigation of diffractive optical element femtosecond laser machining

Energy Technology Data Exchange (ETDEWEB)

Chabrol, Grégoire R., E-mail: g.chabrol@ecam-strasbourg.eu [ECAM Strasbourg-Europe, Espace Européen de l’entreprise, 2, rue de Madrid – 67300 SCHILTIGHEIM, CS. 20013, 67012 Strasbourg CEDEX (France); Laboratoire des Sciences de l’Ingénieur, de l’Informatique et de l’Imagerie (ICube), UDS-CNRS, UMR 7357, 300 bld Sébastien Brant, CS 10413, 67412 Illkirch cedex (France); Ciceron, Adline [ECAM Strasbourg-Europe, Espace Européen de l’entreprise, 2, rue de Madrid – 67300 SCHILTIGHEIM, CS. 20013, 67012 Strasbourg CEDEX (France); Laboratoire des Sciences de l’Ingénieur, de l’Informatique et de l’Imagerie (ICube), UDS-CNRS, UMR 7357, 300 bld Sébastien Brant, CS 10413, 67412 Illkirch cedex (France); Twardowski, Patrice; Pfeiffer, Pierre [Laboratoire des Sciences de l’Ingénieur, de l’Informatique et de l’Imagerie (ICube), UDS-CNRS, UMR 7357, 300 bld Sébastien Brant, CS 10413, 67412 Illkirch cedex (France); Télécom Physique Strasbourg – Pôle API – 300 Bd Sébastien Brant – CS 10413, Illkirch Graffenstaden F 67400 (France); and others

2016-06-30

Highlights: • A method for rapid manufacturing of optical diffractive element in BK7 is proposed. • A binary grating in BK7 was successfully machined by femtosecond laser pulses. • Process relying on nonlinear absorption in the dielectric due to photoionization. • The binary grating was analysed by SEM and interferometric microscopy. • Simulations by Fourier modal method supported the measured diffractive efficiency. - Abstract: This paper presents an explorative study on the machining of diffractive optical elements (DOEs) in transparent materials using a femtosecond laser source. A simple form of DOE, a binary phase grating with a period of 20.85 μm (σ = 0.5 μm), a groove depth and width of 0.7 μm (σ = 0.2 μm) and 8.8 μm (σ = 0.5 μm) respectively, was successfully machined in BK7. The topographic characteristics were measured by white light interferometry and scanning electron microscopy (SEM). The processing was carried out on high precision stages with an ultrafast fibre laser (350 fs) emitting a 343 nm pulse focused onto the sample with a stationary microscope objective. A diffracted efficiency of 27%, obtained with a spectro goniometer, was corroborated by the theoretical results obtained by the Fourier modal method (FMM), taking into account the measured topographic values. These encouraging results demonstrate that high-speed femtosecond laser manufacturing of DOE in bulk glasses can be achieved, opening the way to rapid prototyping of multi-layered-DOEs.

Assessment of species-specific and temporal variations of major, trace and rare earth elements in vineyard ambient using moss bags.

Science.gov (United States)

Milićević, Tijana; Aničić Urošević, Mira; Vuković, Gordana; Škrivanj, Sandra; Relić, Dubravka; Frontasyeva, Marina V; Popović, Aleksandar

2017-10-01

Since the methodological parameters of moss bag biomonitoring have rarely been investigated for the application in agricultural areas, two mosses, Sphagnum girgensohnii (a species of the most recommended biomonitoring genus) and Hypnum cupressiforme (commonly available), were verified in a vineyard ambient. The moss bags were exposed along transects in six vineyard parcels during the grapevine season (March‒September 2015). To select an appropriate period for the reliable 'signal' of the element enrichment in the mosses, the bags were simultaneously exposed during five periods (3 × 2 months, 1 × 4 months, and 1 × 6 months). Assuming that vineyard is susceptible to contamination originated from different agricultural treatments, a wide range of elements (41) were determined in the moss and topsoil samples. The mosses were significantly enriched by the elements during the 2-month bag exposure which gradually increasing up to 6 months, but Cu and Ni exhibited the noticeable fluctuations during the grapevine season. However, the 6-month exposure of moss bags could be recommended for comparative studies among different vineyards because it reflects the ambient pollution comprising unpredictable treatments of grapevine applied during the whole season. Although higher element concentrations were determined in S. girgensohnii than H. cupressiforme, both species reflected the spatio-temporal changes in the ambient element content. Moreover, the significant correlation of the element (Cr, Cu, Sb, and Ti) concentrations between the mosses, and the same pairs of the elements correlated within the species, imply the comparable use of S. girgensohnii and H. cupressiforme in the vineyard (agricultural) ambient. Finally, both the moss bags and the soil analyses suggest that vineyard represents a dominant diffuse pollution source of As, Cr, Cu, Ni, Fe, and V. Copyright © 2017 Elsevier Inc. All rights reserved.

Convenience of Statistical Approach in Studies of Architectural Ornament and Other Decorative Elements Specific Application

Science.gov (United States)

Priemetz, O.; Samoilov, K.; Mukasheva, M.

2017-11-01

An ornament is an actual phenomenon of the architecture modern theory, a common element in the practice of design and construction. It has been an important aspect of shaping for millennia. The description of the methods of its application occupies a large place in the studies on the theory and practice of architecture. However, the problem of the saturation of compositions with ornamentation, the specificity of its themes and forms have not been sufficiently studied yet. This aspect requires accumulation of additional knowledge. The application of quantitative methods for the plastic solutions types and a thematic diversity of facade compositions of buildings constructed in different periods creates another tool for an objective analysis of ornament development. It demonstrates the application of this approach for studying the features of the architectural development in Kazakhstan at the end of the XIX - XXI centuries.

Cis-acting elements in the promoter region of the human aldolase C gene.

Science.gov (United States)

Buono, P; de Conciliis, L; Olivetta, E; Izzo, P; Salvatore, F

1993-08-16

We investigated the cis-acting sequences involved in the expression of the human aldolase C gene by transient transfections into human neuroblastoma cells (SKNBE). We demonstrate that 420 bp of the 5'-flanking DNA direct at high efficiency the transcription of the CAT reporter gene. A deletion between -420 bp and -164 bp causes a 60% decrease of CAT activity. Gel shift and DNase I footprinting analyses revealed four protected elements: A, B, C and D. Competition analyses indicate that Sp1 or factors sharing a similar sequence specificity bind to elements A and B, but not to elements C and D. Sequence analysis shows a half palindromic ERE motif (GGTCA), in elements B and D. Region D binds a transactivating factor which appears also essential to stabilize the initiation complex.

Improvements to Technical Specifications surveillance requirements

International Nuclear Information System (INIS)

Lobel, R.; Tjader, T.R.

1992-12-01

In August 1983 an NRC task group was formed to investigate problems with surveillance testing required by Technical Specifications, and to recommend approaches to effect improvements. NUREG-1024 (''Technical Specifications-Enhancing Safety Impact'') resulted, and it contained recommendations to review the basis for test frequencies; to ensure that the tests promote safety and do not degrade equipment; and to review surveillance tests so that they do not unnecessarily burden personnel. The Technical Specifications Improvement Program (TSIP) was established in December 1984 to provide the framework for rewriting and improving the Technical Specifications. As an element of the TSIP, all Technical Specifications surveillance requirements were comprehensively examined as recommended in NUREG-1024. The results of that effort are presented in this report. The study found that while some testing at power is essential to verify equipment and system operability, safety can be improved, equipment degradation decreased, and unnecessary personnel burden relaxed by reducing the amount of testing at power

Application of multivariate analysis to investigate the trace element contamination in top soil of coal mining district in Jorong, South Kalimantan, Indonesia

Science.gov (United States)

Pujiwati, Arie; Nakamura, K.; Watanabe, N.; Komai, T.

2018-02-01

Multivariate analysis is applied to investigate geochemistry of several trace elements in top soils and their relation with the contamination source as the influence of coal mines in Jorong, South Kalimantan. Total concentration of Cd, V, Co, Ni, Cr, Zn, As, Pb, Sb, Cu and Ba was determined in 20 soil samples by the bulk analysis. Pearson correlation is applied to specify the linear correlation among the elements. Principal Component Analysis (PCA) and Cluster Analysis (CA) were applied to observe the classification of trace elements and contamination sources. The results suggest that contamination loading is contributed by Cr, Cu, Ni, Zn, As, and Pb. The elemental loading mostly affects the non-coal mining area, for instances the area near settlement and agricultural land use. Moreover, the contamination source is classified into the areas that are influenced by the coal mining activity, the agricultural types, and the river mixing zone. Multivariate analysis could elucidate the elemental loading and the contamination sources of trace elements in the vicinity of coal mine area.

The effect of seated pelvic tilt on posterior edge-loading in total hip arthroplasty: A finite element investigation.

Science.gov (United States)

Pierrepont, Jim; Yang, Long; Arulampalam, Jevan; Stambouzou, Catherine; Miles, Brad; Li, Qing

2018-03-01

Edge-loading of a ceramic-on-ceramic total hip replacement can lead to reproducible squeaking and revision. A patient's functional acetabular cup orientation, driven by their pelvic tilt, has been shown to be a significant factor in squeaking during hip flexion. The aim of this study was to investigate the effect of seated pelvic tilt on the contact mechanics at the ceramic bearing surface. A finite element model of a ceramic-on-ceramic total hip replacement was created. The cup was orientated at 40° inclination and 15° anteversion relative to the anterior pelvic plane. The stem was flexed 90° to replicate sitting in a chair. The model was loaded using data from in vivo measurements taken during a sit-to-stand activity. The pelvis was modelled in seven different sagittal positions, ranging from -30° to 30° of pelvic tilt, where a positive value denotes anterior pelvic tilt. Three different head sizes were investigated: 32, 36 and 40 mm. The maximum contact pressure and contact patch to rim distance were determined for each of the 21 simulations. Edge-loading (contact patch to rim distance Edge-loading initiated at seated pelvic tilts of 7°, 9° and 5° for the 32, 36 and 40 mm heads, respectively. Patients with anterior pelvic tilts in the seated position are susceptible to posterior edge-loading. As the position of the pelvis when seated is patient specific, cup orientation should be adjusted on an individual basis to minimise edge-loading.

Investigation of stacked elemental layers for Cu(In,Ga)Se{sub 2} thin film preparation by rapid thermal selenization

Energy Technology Data Exchange (ETDEWEB)

Stroth, Christiane; Ohland, Joerg; Mikolajczak, Ulf; Madena, Thomas; Keller, Jan; Parisi, Juergen; Hammer, Maria; Riedel, Ingo [Energy and Semiconductor Research Laboratory, Department of Physics, University of Oldenburg, 26111 Oldenburg (Germany)

2013-07-01

Rapid thermal selenization of pure metallic (Cu-In-Ga) or selenium-containing (Cu-In-Ga-Se) precursors is a favorable method to fabricate Cu(In,Ga)Se{sub 2} absorber films for application in thin film solar cells. Because of its upscaling potential and the short process time it is a promising approach for the fabrication of CIGSe photovoltaic modules on industrial scale. As a preliminary work for prospective plasma-enhanced selenization of stacked elemental layers (SEL) the elements copper, indium and gallium were sequentially deposited on molybdenum coated soda-lime glass by thermal evaporation. The stacking order was varied and the precursors were annealed with different heating rates. Morphology, elemental depth distribution and phases of the layers were investigated before and after annealing using scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. Furthermore the influence of different heating rates on phase transitions during annealing was studied by in-situ X-ray diffraction.

Numerical investigation of soil and buried structures using finite element analysis

Directory of Open Access Journals (Sweden)

Meysam Shirzad Shahrivar

2017-02-01

Full Text Available Today the important of studying soil effect on behavior of soil  contacted structures such as foundations, piles,  retaining wall and other similar structures is so much that neglecting of soil-structure interaction effect can cause to untrue results. In this paper soil-structure interaction simulation was done by using Finite element method analysis with ABAQUS version 6.13-14.The results has been presented based on pile function in contact with soil, vertical stresses in soil and structures, pore pressure in drained and undrained condition and underground water level.Final conclusions revealed that pore pressure effect is not uniform on all parts of pile and amount of pore pressure increment in top elements is lower than down elements of  pile.Further it was proven that average amount of vertical stress on end of pile is    of this stress on top of the pile. thus it was concluded that 70% of pile bearing capacity is depend on friction of soil and pile contact surface.

A preliminary investigation of finite-element modeling for composite rotor blades

Science.gov (United States)

Lake, Renee C.; Nixon, Mark W.

1988-01-01

The results from an initial phase of an in-house study aimed at improving the dynamic and aerodynamic characteristics of composite rotor blades through the use of elastic couplings are presented. Large degree of freedom shell finite element models of an extension twist coupled composite tube were developed and analyzed using MSC/NASTRAN. An analysis employing a simplified beam finite element representation of the specimen with the equivalent engineering stiffness was additionally performed. Results from the shell finite element normal modes and frequency analysis were compared to those obtained experimentally, showing an agreement within 13 percent. There was appreciable degradation in the frequency prediction for the torsional mode, which is elastically coupled. This was due to the absence of off-diagonal coupling terms in the formulation of the equivalent engineering stiffness. Parametric studies of frequency variation due to small changes in ply orientation angle and ply thickness were also performed. Results showed linear frequency variations less than 2 percent per 1 degree variation in the ply orientation angle, and 1 percent per 0.0001 inch variation in the ply thickness.

An automatic method to generate domain-specific investigator networks using PubMed abstracts

Directory of Open Access Journals (Sweden)

Gwinn Marta

2007-06-01

web-based prototype capable of creating domain-specific investigator networks based on an application that accurately generates detailed investigator profiles from PubMed abstracts combined with robust standard vocabularies. This approach could be used for other biomedical fields to efficiently establish domain-specific investigator networks.

An automatic method to generate domain-specific investigator networks using PubMed abstracts

Science.gov (United States)

Yu, Wei; Yesupriya, Ajay; Wulf, Anja; Qu, Junfeng; Gwinn, Marta; Khoury, Muin J

2007-01-01

capable of creating domain-specific investigator networks based on an application that accurately generates detailed investigator profiles from PubMed abstracts combined with robust standard vocabularies. This approach could be used for other biomedical fields to efficiently establish domain-specific investigator networks. PMID:17584920

[Investigation on Main Cultivation of Astragalus membranaceus var. mongholicus and Commercial Specifications Grades].

Science.gov (United States)

Zhang, He-ting; Wang, Jian; Cheng, Ming-en; Duan, Hai-yan; Peng, Hua-sheng

2015-12-01

To investigate the main cultivation areas of Astragalus membranaceus var. mongholicus, and to clarify its present cultivation status and commercial specification grades. Astragalus membranaceus var. mongholicus cultivated in Hunyuan and Ying County of Shanxi, Longxi, Weiyuan and Min County of Gansu and Wuchuan, Guyang and Chifeng of Inner Mongolia were investigated, including their ecological environment, cultivation history and present situation, harvesting and processing as well as commercial specification grades. The cultivation methods of Astragalus membranaceus var. mongholicus changed greatly in the main cultivation areas. In Gansu and Inner Mongolia, the current major cultivation method was 2 - 3 years of seedling transplantation method, while the 3 - 5 years of seed-directly-sowed method in Inner Mongolia had been almost abandoned, and the 6 - 8 years of mountain direct seeding method was still in application in Hunyuan county of Shanxi province. On the other hand, the harvest method of Astragalus membranaceus var. mongholicus had been gradually changed from manual harvesting in ancient times to the current mechanical harvesting although the latter method did more damage to environment of cultivation areas and the resource of Astragalus membranaceus var. mongholicus in regions Hunyuan county of Shanxi. Through investigating the processing methods of Astragalus membranaceus var. mongholicus in different cultivation areas, it was found that processing method varied from area to area, and no unified specifications had been formulated on processing methods in market. In addition, the current processing method was too complicated in processing the slices of prepared Astragali Radix and most were self processing by farmers themselves, creating market disorders. Moreover, the Astragali Radix products were basically without grading classification but sold as bulk cargo. It is urgent to unify the specifications and grades of Astragali Radix product, and standardize

WAG 2 remedial investigation and site investigation site-specific work plan/health and safety checklist for the soil and sediment task

International Nuclear Information System (INIS)

Holt, V.L.; Burgoa, B.B.

1993-12-01

This document is a site-specific work plan/health and safety checklist (WP/HSC) for a task of the Waste Area Grouping 2 Remedial Investigation and Site Investigation (WAG 2 RI ampersand SI). Title 29 CFR Part 1910.120 requires that a health and safety program plan that includes site- and task-specific information be completed to ensure conformance with health- and safety-related requirements. To meet this requirement, the health and safety program plan for each WAG 2 RI ampersand SI field task must include (1) the general health and safety program plan for all WAG 2 RI ampersand SI field activities and (2) a WP/HSC for that particular field task. These two components, along with all applicable referenced procedures, must be kept together at the work site and distributed to field personnel as required. The general health and safety program plan is the Health and Safety Plan for the Remedial Investigation and Site Investigation of Waste Area Grouping 2 at the Oak Ridge National Laboratory, Oak Ridge, Tennessee (ORNL/ER-169). The WP/HSCs are being issued as supplements to ORNL/ER-169

A boundary element model for investigating the effects of eye tumor on the temperature distribution inside the human eye.

Science.gov (United States)

Ooi, E H; Ang, W T; Ng, E Y K

2009-08-01

A three-dimensional boundary element model of the human eye is developed to investigate the thermal effects of eye tumor on the ocular temperature distribution. The human eye is modeled as comprising several regions which have different thermal properties. The tumor is one of these regions. The thermal effects of the tumor are simulated by taking it to have a very high metabolic heat generation and blood perfusion rate. Inside the tumor, the steady state temperature is governed by the Pennes bioheat equation. Elsewhere, in normal tissues of the eye, the temperature satisfies the Laplace's equation. To compute the temperature on the corneal surface, the surface boundary of each region is divided into triangular elements.

Correlations and fixation of some elements in tree rings

International Nuclear Information System (INIS)

Goldberg, E.L.; Zolotarev, K.B.; Maksimovskaya, V.V.; Kondratyev, V.I.; Ovchinnikov, D.V.; Naurzbaev, M.M.

2007-01-01

High-resolution scanning with Synchrotron Radiation X-ray Fluorescence Analysis (SRXFA) was applied to investigate element distributions in tree rings. Two cores of Siberia Larch have been investigated with resolution 100-200 mkm. Two groups of elements in tree rings with different trends have been found. The members of the first group are Br, Zn, Cl, whose trends correlate with each other. Moreover, trends of Br, Zn, Cl in tree rings are similar to the trend of atmosphere precipitation in the region investigated. Other group of elements are represented by K, Ca, Sr, Mn, Fe, but their trends differ sufficiently from trend of elements of the first group. Extended fixation of elements in tree rings is observed for elements of the first group over the whole interval investigated (150 years). In contrast, elements of the second group mainly accumulate in external part of tree stem

Analogs for transuranic elements

International Nuclear Information System (INIS)

Weimer, W.C.; Laul, J.C.; Kutt, J.C.

1981-01-01

A combined theoretical and experimental approach is being used to estimate the long-term environmental and biogeochemical behaviors of selected transuranic elements. The objective of this research is to estimate the effect that long-term (hundreds of years) environmental weathering has on the behavior of the transuranic elements americium and curium. This is achieved by investigating the actual behavior of naturally occurring rare earth elements, especially neodymium, that serve as transuranic analogs. Determination of the analog element behavior provides data that can be used to estimate the ultimate availability to man of transuranic materials released into the environment

Short interspersed nuclear elements (SINEs) are abundant in Solanaceae and have a family-specific impact on gene structure and genome organization.

Science.gov (United States)

Seibt, Kathrin M; Wenke, Torsten; Muders, Katja; Truberg, Bernd; Schmidt, Thomas

2016-05-01

Short interspersed nuclear elements (SINEs) are highly abundant non-autonomous retrotransposons that are widespread in plants. They are short in size, non-coding, show high sequence diversity, and are therefore mostly not or not correctly annotated in plant genome sequences. Hence, comparative studies on genomic SINE populations are rare. To explore the structural organization and impact of SINEs, we comparatively investigated the genome sequences of the Solanaceae species potato (Solanum tuberosum), tomato (Solanum lycopersicum), wild tomato (Solanum pennellii), and two pepper cultivars (Capsicum annuum). Based on 8.5 Gbp sequence data, we annotated 82 983 SINE copies belonging to 10 families and subfamilies on a base pair level. Solanaceae SINEs are dispersed over all chromosomes with enrichments in distal regions. Depending on the genome assemblies and gene predictions, 30% of all SINE copies are associated with genes, particularly frequent in introns and untranslated regions (UTRs). The close association with genes is family specific. More than 10% of all genes annotated in the Solanaceae species investigated contain at least one SINE insertion, and we found genes harbouring up to 16 SINE copies. We demonstrate the involvement of SINEs in gene and genome evolution including the donation of splice sites, start and stop codons and exons to genes, enlargement of introns and UTRs, generation of tandem-like duplications and transduction of adjacent sequence regions. © 2016 The Authors The Plant Journal © 2016 John Wiley & Sons Ltd.

Elemental investigation of (Al-Cu) alloys and some geological samples using neutron activation and XRF analysis techniques

International Nuclear Information System (INIS)

Hammad, E.A.M.

2012-01-01

Neutron activation analysis (NAA) using k 0 - standardization (k 0 -NAA) is well known method for multi-elemental analysis. The method is used to analyze different samples belonging to different fields. In addition, X- ray fluorescence (XRF) is also used for multi-elemental analysis. XRF complements NAA methods. Both methods were used for investigation of some iron ores and aluminum- cupper alloy (Al-Cu) samples. Elemental concentration of Iron ores and Al-Cu alloy samples were determined by k 0 - NAA and XRF methods. The iron ore samples were collected from Wadi Kareim and Umm Nar sites (the Eastern desert of Egypt). Six and two samples representing the ores of Wadi Kareim and Umm Nar, respectively altogether with the standard samples consisting of Fe, Au , Zr and W and the certified reference sample IAEA Soil-7 were irradiated in one of the irradiated boxes at the Second Egyptian Research Reactor (ETRR- 2). The induced activities were counted using an efficiency calibrated HPGe detector systems. The neutron spectrum parameters α and f characterizing the neutron irradiation position that are needed in applying k 0 -NAA method were determined using the activation product of Zr , Au, Fe and W and found α≅ - 0.048 ±0.002 and f ≅ 38± k 0 -NAA method was applied to determine the elemental concentrations in the two iron ore samples. The concentrations determined were found to vary erratically form one sample to another. The results were discussed and compared with similar results in literature. The accuracy of the k 0 - NAA method was checked by determining the elemental concentration in the IAEA-Soil 7 reference sample. The obtained results are compared with the recommended values. Good agreements were found within 10 %. Short time neutron activation analysis (STNAA) was carried out to determine concentration of major elements in Al-Cu alloy samples. Three (Al-Cu) alloys samples with different concentrations of Cu (2, 3.5 and 5 %) altogether. Au standard sample

Investigation of arc repressor DNA-binding specificity by comparative molecular dynamics simulations.

Science.gov (United States)

Song, Wei; Guo, Jun-Tao

2015-01-01

Transcription factors regulate gene expression through binding to specific DNA sequences. How transcription factors achieve high binding specificity is still not well understood. In this paper, we investigated the role of protein flexibility in protein-DNA-binding specificity by comparative molecular dynamics (MD) simulations. Protein flexibility has been considered as a key factor in molecular recognition, which is intrinsically a dynamic process involving fine structural fitting between binding components. In this study, we performed comparative MD simulations on wild-type and F10V mutant P22 Arc repressor in both free and complex conformations. The F10V mutant has lower DNA-binding specificity though both the bound and unbound main-chain structures between the wild-type and F10V mutant Arc are highly similar. We found that the DNA-binding motif of wild-type Arc is structurally more flexible than the F10V mutant in the unbound state, especially for the six DNA base-contacting residues in each dimer. We demonstrated that the flexible side chains of wild-type Arc lead to a higher DNA-binding specificity through forming more hydrogen bonds with DNA bases upon binding. Our simulations also showed a possible conformational selection mechanism for Arc-DNA binding. These results indicate the important roles of protein flexibility and dynamic properties in protein-DNA-binding specificity.

Multi-elemental imaging of paraffin-embedded human samples by laser-induced breakdown spectroscopy

Science.gov (United States)

Moncayo, S.; Trichard, F.; Busser, B.; Sabatier-Vincent, M.; Pelascini, F.; Pinel, N.; Templier, I.; Charles, J.; Sancey, L.; Motto-Ros, V.

2017-07-01

Chemical elements play central roles for physiological homeostasis in human cells, and their dysregulation might lead to a certain number of pathologies. Novel imaging techniques that improve the work of pathologists for tissue analysis and diagnostics are continuously sought. We report the use of Laser-Induced Breakdown Spectroscopy (LIBS) to perform multi-elemental images of human paraffin-embedded skin samples on the entire biopsy scale in a complementary and compatible way with microscope histopathological examination. A specific instrumental configuration is proposed in order to detect most of the elements of medical interest (i.e. P, Al, Mg, Na, Zn, Si, Fe, and Cu). As an example of medical application, we selected and analysed skin biopsies, including healthy skin tissue, cutaneous metastasis of melanoma, Merkel-cell carcinoma and squamous cell carcinoma. Clear distinctions in the distribution of chemical elements are observed from the different samples investigated. This study demonstrates the high complementarity of LIBS elemental imaging with conventional histopathology, opening new opportunities for any medical application involving metals.

Positive- and negative-acting regulatory elements contribute to the tissue-specific expression of INNER NO OUTER, a YABBY-type transcription factor gene in Arabidopsis

Directory of Open Access Journals (Sweden)

Simon Marissa K

2012-11-01

Full Text Available Abstract Background The INNER NO OUTER (INO gene, which encodes a YABBY-type transcription factor, specifies and promotes the growth of the outer integument of the ovule in Arabidopsis. INO expression is limited to the abaxial cell layer of the developing outer integument of the ovule and is regulated by multiple regions of the INO promoter, including POS9, a positive element that when present in quadruplicate can produce low-level expression in the normal INO pattern. Results Significant redundancy in activity between different regions of the INO promoter is demonstrated. For specific regulatory elements, multimerization or the addition of the cauliflower mosaic virus 35S general enhancer was able to activate expression of reporter gene constructs that were otherwise incapable of expression on their own. A new promoter element, POS6, is defined and is shown to include sufficient positive regulatory information to reproduce the endogenous pattern of expression in ovules, but other promoter regions are necessary to fully suppress expression outside of ovules. The full-length INO promoter, but not any of the INO promoter deletions tested, is able to act as an enhancer-blocking insulator to prevent the ectopic activation of expression by the 35S enhancer. Sequence conservation between the promoter regions of Arabidopsis thaliana, Brassica oleracea and Brassica rapa aligns closely with the functional definition of the POS6 and POS9 regions, and with a defined INO minimal promoter. The B. oleracea INO promoter is sufficient to promote a similar pattern and level of reporter gene expression in Arabidopsis to that observed for the Arabidopsis promoter. Conclusions At least two independent regions of the INO promoter contain sufficient regulatory information to direct the specific pattern but not the level of INO gene expression. These regulatory regions act in a partially redundant manner to promote the expression in a specific pattern in the ovule and

Finite element computational fluid mechanics

International Nuclear Information System (INIS)

Baker, A.J.

1983-01-01

This book analyzes finite element theory as applied to computational fluid mechanics. It includes a chapter on using the heat conduction equation to expose the essence of finite element theory, including higher-order accuracy and convergence in a common knowledge framework. Another chapter generalizes the algorithm to extend application to the nonlinearity of the Navier-Stokes equations. Other chapters are concerned with the analysis of a specific fluids mechanics problem class, including theory and applications. Some of the topics covered include finite element theory for linear mechanics; potential flow; weighted residuals/galerkin finite element theory; inviscid and convection dominated flows; boundary layers; parabolic three-dimensional flows; and viscous and rotational flows

New elements

International Nuclear Information System (INIS)

Flerov, G.

1976-01-01

The history is briefly described of the investigation of superheavy elements at the Joint Institute for Nuclear Research at Dubna. The significance of the investigation is assessed from the point of view of the nuclear structure study and major problems encountered in experimental efforts are indicated. Current experimental methods aiming at the discovery or the production of superheavy nuclei with Z approximately 114 are listed. (I.W.)

Comprehensive evaluation of disease- and trait-specific enrichment for eight functional elements among GWAS-identified variants.

Science.gov (United States)

Markunas, Christina A; Johnson, Eric O; Hancock, Dana B

2017-07-01

Genome-wide association study (GWAS)-identified variants are enriched for functional elements. However, we have limited knowledge of how functional enrichment may differ by disease/trait and tissue type. We tested a broad set of eight functional elements for enrichment among GWAS-identified SNPs (p Enrichment analyses were conducted using logistic regression, with Bonferroni correction. Overall, a significant enrichment was observed for all functional elements, except sequence motifs. Missense SNPs showed the strongest magnitude of enrichment. eQTLs were the only functional element significantly enriched across all diseases/traits. Magnitudes of enrichment were generally similar across diseases/traits, where enrichment was statistically significant. Blood vs. brain tissue effects on enrichment were dependent on disease/trait and functional element (e.g., cardiovascular disease: eQTLs P TissueDifference  = 1.28 × 10 -6 vs. enhancers P TissueDifference  = 0.94). Identifying disease/trait-relevant functional elements and tissue types could provide new insight into the underlying biology, by guiding a priori GWAS analyses (e.g., brain enhancer elements for psychiatric disease) or facilitating post hoc interpretation.

Measurement of elemental distributions in mouse brain by using submilli-PIXE camera

International Nuclear Information System (INIS)

Fujiki, K.; Matsuyama, S.; Ishii, K.

2010-01-01

In a biological body, trace elements including metallic elements play important roles. Knowing their spatial distribution and amounts, we can find out some relations among a physiological role of the trace element in vivo, the function, and the disease appearance. In this study, we investigated a method to obtain elemental distributions in whole brain slice taken from mental disease model mice and control mice using in-air submilli-PIXE camera at Tohoku University. We administered 5-BrdU that was the analogue of the thymidine as a marker to detect a new born cell in especially the dentate gyrus of the hippocampus. We obtained the elemental distributions of the whole brain of subject and control mice. From elemental distributions of the brain of a mental disease model mouse, a brain contained light elements, such as P, S, Cl and K, which were uniformly distributed over the brain. Fe was accumulated in the specific area of brain. Elemental concentration of Fe was more than 10 times higher than that in the other. However, the accumulation of iron in brain slices was not observed in those of control mice. Zn is accumulated in the vicinity in hippocampus. Br was uniformly distributed over the brain. The submilli-PIXE camera will provide a powerful tool for this research. (author)

Evaluation of the Physiological Challenges in Extreme Environments: Implications for Enhanced Training, Operational Performance and Sex-Specific Responses

Science.gov (United States)

2017-10-01

Operational Performance and Sex -Specific Responses PRINCIPAL INVESTIGATOR: Brent C. Ruby CONTRACTING ORGANIZATION: The University of Montana Missoula...Implications for Enhanced Training, Operational Performance and Sex -Specific Responses 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...Evaluation of the physiological challenges in extreme environments: Implications for enhanced training, operational performance and sex -specific

Population specific absorption studies for some diet incorporated trace elements : comparison with ICRP data

International Nuclear Information System (INIS)

Parameswaran, M.; Dang, H.S.

1999-01-01

Daily intake and excretion can provide an important information regarding the absorption through the gastro-intestinal tract (f1 factor) of trace elements incorporated in diet. The absorption may depend upon the kind of diet consumed, the content of the fibre, protein etc and it could be quite different for two populations groups with entirely different food habits. ICRP has provided data on the intake and excretion of 63 trace elements by Caucasian population representing North American and European adults. This paper reports intake and excretion of twelve elements Na, K, Ca, Mg, Cu, Mn, Rb, Fe, Zn, Sr, Li and Cr for an urban adult Indian population group and compares with corresponding data on ICRP reference man. (author)

Finite element modeling of piezoelectric elements with complex electrode configuration

International Nuclear Information System (INIS)

Paradies, R; Schläpfer, B

2009-01-01

It is well known that the material properties of piezoelectric materials strongly depend on the state of polarization of the individual element. While an unpolarized material exhibits mechanically isotropic material properties in the absence of global piezoelectric capabilities, the piezoelectric material properties become transversally isotropic with respect to the polarization direction after polarization. Therefore, for evaluating piezoelectric elements the material properties, including the coupling between the mechanical and the electromechanical behavior, should be addressed correctly. This is of special importance for the micromechanical description of piezoelectric elements with interdigitated electrodes (IDEs). The best known representatives of this group are active fiber composites (AFCs), macro fiber composites (MFCs) and the radial field diaphragm (RFD), respectively. While the material properties are available for a piezoelectric wafer with a homogeneous polarization perpendicular to its plane as postulated in the so-called uniform field model (UFM), the same information is missing for piezoelectric elements with more complex electrode configurations like the above-mentioned ones with IDEs. This is due to the inhomogeneous field distribution which does not automatically allow for the correct assignment of the material, i.e. orientation and property. A variation of the material orientation as well as the material properties can be accomplished by including the polarization process of the piezoelectric transducer in the finite element (FE) simulation prior to the actual load case to be investigated. A corresponding procedure is presented which automatically assigns the piezoelectric material properties, e.g. elasticity matrix, permittivity, and charge vector, for finite element models (FEMs) describing piezoelectric transducers according to the electric field distribution (field orientation and strength) in the structure. A corresponding code has been

Superheavy element chemistry. Achievements and perspectives

International Nuclear Information System (INIS)

Schaedel, M.

2007-01-01

Superheavy elements have been synthesized and chemically characterized one-atom-at-a-time up to element 108. Presently, the quest for element 112 is one of the hottest topics in this field. The transactinide elements 104 to 108 are members of group 4 to 8 of the Periodic Table and element 112 belongs into group 12. Chemical properties of some of these elements, like elements 104 and 105, show stunning deviations from simple extrapolations within their respective group while others exhibit great similarities with their lighter homologues elements. First experiments to investigate seaborgium (Sg, element 106) in aqueous solution were performed. Again, in large international collaborations at the GSI, several gas-phase chemistry experiments were performed with hassium (Hs, element 108). Recently, the highly efficient and very clean separation of Hs was applied for nuclear studies of various Hs nuclides investigating their cross section and their nuclear decay properties in the region of the doubly-magic 270 Hs (Z=108, N=162). To overcome certain limitations of the presently used on-line chemical separations the new TransActinide Separation and Chemistry Apparatus (TASCA) - with a gas-filled recoil separator as a front-end tool - was designed and built at the GSI in a collaborative effort. Presently in its commissioning phase, TASCA shall be a key instrument for a big leap into quantitatively and qualitatively new experiments in the region of superheavy elements. (author)

Analog elements for transuranic chemistries

International Nuclear Information System (INIS)

Weimer, W.C.

1982-01-01

The analytical technique for measuring trace concentrations of the analog rare earth elements has been refined for optimal detection. The technique has been used to determine the rare earth concentrations in a series of geological and biological materials, including samples harvested from controlled lysimeter investigations. These studies have demonstrated that any of the trivalent rare earth elements may be used as analog elements for the trivalent transuranics, americium and curium

Echicetin coated polystyrene beads: a novel tool to investigate GPIb-specific platelet activation and aggregation.

Directory of Open Access Journals (Sweden)

Alexey Navdaev

Full Text Available von Willebrand factor/ristocetin (vWF/R induces GPIb-dependent platelet agglutination and activation of αIIbβ3 integrin, which also binds vWF. These conditions make it difficult to investigate GPIb-specific signaling pathways in washed platelets. Here, we investigated the specific mechanisms of GPIb signaling using echicetin-coated polystyrene beads, which specifically activate GPIb. We compared platelet activation induced by echicetin beads to vWF/R. Human platelets were stimulated with polystyrene beads coated with increasing amounts of echicetin and platelet activation by echicetin beads was then investigated to reveal GPIb specific signaling. Echicetin beads induced αIIbβ3-dependent aggregation of washed platelets, while under the same conditions vWF/R treatment led only to αIIbβ3-independent platelet agglutination. The average distance between the echicetin molecules on the polystyrene beads must be less than 7 nm for full platelet activation, while the total amount of echicetin used for activation is not critical. Echicetin beads induced strong phosphorylation of several proteins including p38, ERK and PKB. Synergistic signaling via P2Y12 and thromboxane receptor through secreted ADP and TxA2, respectively, were important for echicetin bead triggered platelet activation. Activation of PKG by the NO/sGC/cGMP pathway inhibited echicetin bead-induced platelet aggregation. Echicetin-coated beads are powerful and reliable tools to study signaling in human platelets activated solely via GPIb and GPIb-triggered pathways.

Echicetin Coated Polystyrene Beads: A Novel Tool to Investigate GPIb-Specific Platelet Activation and Aggregation

Science.gov (United States)

Petunin, Alexey; Clemetson, Kenneth J.; Gambaryan, Stepan; Walter, Ulrich

2014-01-01

von Willebrand factor/ristocetin (vWF/R) induces GPIb-dependent platelet agglutination and activation of αIIbβ3 integrin, which also binds vWF. These conditions make it difficult to investigate GPIb-specific signaling pathways in washed platelets. Here, we investigated the specific mechanisms of GPIb signaling using echicetin-coated polystyrene beads, which specifically activate GPIb. We compared platelet activation induced by echicetin beads to vWF/R. Human platelets were stimulated with polystyrene beads coated with increasing amounts of echicetin and platelet activation by echicetin beads was then investigated to reveal GPIb specific signaling. Echicetin beads induced αIIbβ3-dependent aggregation of washed platelets, while under the same conditions vWF/R treatment led only to αIIbβ3-independent platelet agglutination. The average distance between the echicetin molecules on the polystyrene beads must be less than 7 nm for full platelet activation, while the total amount of echicetin used for activation is not critical. Echicetin beads induced strong phosphorylation of several proteins including p38, ERK and PKB. Synergistic signaling via P2Y12 and thromboxane receptor through secreted ADP and TxA2, respectively, were important for echicetin bead triggered platelet activation. Activation of PKG by the NO/sGC/cGMP pathway inhibited echicetin bead-induced platelet aggregation. Echicetin-coated beads are powerful and reliable tools to study signaling in human platelets activated solely via GPIb and GPIb-triggered pathways. PMID:24705415

Controlled Dissolution of Surface Layers for Elemental Analysis by Inductively Coupled Plasma-Mass Spectrometry

Energy Technology Data Exchange (ETDEWEB)

Lorge, Susan Elizabeth [Iowa State Univ., Ames, IA (United States)

2007-01-01

representation of the sample layer cannot be realized. Specifically, the ratio of analyte signal to matrix element signal does not equal the actual ratio in the bulk sample. The objective of this work was to investigate the controlled dissolution of other materials, simpler than steel. Matrices of copper, high copper alloy and NIST C1100 brass were investigated but the matrix that showed the best agreement between measured and certified values was NIST 612 glass. Further studies were conducted to limit the amount of surface layers removed for the NIST 612 matrix.

The challenges of translating culturally specific elements: the case of Mikhail Bulgakov’s The Master and Margarita

Directory of Open Access Journals (Sweden)

Natalia Kaloh Vid

2016-12-01

Full Text Available Mikhail Bulgakov’s novel The Master and Margarita, a highly complex and multi-levelled narrative, is a challenge for any translator. The emphasis in the current research is on the translation strategies used when translating culturally-specific elements, or historical realia, referred to as “Sovietisms,” in three English translations of the novel by Glenny (1967, Pevear and Volokhonsky (1997 and Aplin (2008. Sovietisms refer to items characteristic of the Soviet discourse of the 1930s: word-formations of the non-standard “Soviet Russian.” Bulgakov’s language is sated with Soviet vocabulary, which refers to various cultural and socio-political elements of Soviet reality. Sovietisms occur at various levels (lexical,syntactic, stylistic and rhetorical and should be carefully translated as a significant characteristic of Bulgakov’s style. A complete domestication of Sovietisms may lead to a loss of a connotative meaning essential for understanding the context, while a foreignisation of these terms, which are most likely unknown to western readers, may disturb fluidity of reading and cause confusion. The purpose of this analysis, thus, is to illustrate the use of domesticating/foreignising strategies employed by Bulgakov’s translators and to assess the translation choices. The comparative analysis employs the taxonomies suggested by Vlakhov and Florin (1995 and Vinay and Darbelnet (1958/1989 as the grounds for the case study.

Preliminary study of elemental composition in tree leaves for using as bio monitor for air pollution

International Nuclear Information System (INIS)

Chueinta, Wanna; Bunprapob, Supamatthree

2004-10-01

The use of plant tissue as biological monitor of air pollution has been of interest world wild. The study on chemical composition of such biological monitor may provide important information on the levels and pathways of a variety of pollutants including heavy metals and trace toxic elements in atmosphere. The appropriate bio monitors are such as herbaceous plants, tree leaves, bryophytes and lichens, with their possible advantages and/or limitations. In this research an investigation of element composition in leaves was performed. The technique of Instrument Neutron Activation Analysis (INAA) was developed to determine heavy metal and trace elements in 8 species of tree leaves collected from 3 different locations. From the experiments, it was found that content of elements might vary depending on species and environment. Some specific elements are discussed and compared in this report

Best practices in incident investigation in the chemical process industries with examples from the industry sector and specifically from Nova Chemicals

International Nuclear Information System (INIS)

Morrison, Lisa M.

2004-01-01

This paper will summarize best practices in incident investigation in the chemical process industries and will provide examples from both the industry sector and specifically from NOVA Chemicals. As a sponsor of the Center for Chemical Process Safety (CCPS), an industry technology alliance of the American Institute of Chemical Engineers, NOVA Chemicals participates in a number of working groups to help develop best practices and tools for the chemical process and associated industries in order to advance chemical process safety. A recent project was to develop an update on guidelines for investigating chemical process incidents. A successful incident investigation management system must ensure that all incidents and near misses are reported, that root causes are identified, that recommendations from incident investigations identify appropriate preventive measures, and that these recommendations are resolved in a timely manner. The key elements of an effective management system for incident investigation will be described. Accepted definitions of such terms as near miss, incident, and root cause will be reviewed. An explanation of the types of incident classification systems in use, along with expected levels of follow-up, will be provided. There are several incident investigation methodologies in use today by members of the CCPS; most of these methodologies incorporate the use of several tools. These tools include: timelines, sequence diagrams, causal factor identification, brainstorming, checklists, pre-defined trees, and team-defined logic trees. Developing appropriate recommendations and then ensuring their resolution is the key to prevention of similar events from recurring, along with the sharing of lessons learned from incidents. There are several sources of information on previous incidents and lessons learned available to companies. In addition, many companies in the chemical process industries use their own internal databases to track recommendations from

Experimental investigations and finite element simulation of cutting heat in vibrational and conventional drilling of cortical bone.

Science.gov (United States)

Wang, Yu; Cao, Meng; Zhao, Xiangrui; Zhu, Gang; McClean, Colin; Zhao, Yuanyuan; Fan, Yubo

2014-11-01

Heat generated during bone drilling could cause irreversible thermal damage, which can lead to bone necrosis or even osteomyelitis. In this study, vibrational drilling was applied to fresh bovine bones to investigate the cutting heat in comparison with conventional drilling through experimental investigation and finite element analysis (FEA). The influence of vibrational frequency and amplitude on cutting heat generation and conduction were studied. The experimental results showed that, compared with the conventional drilling, vibrational drilling could significantly reduce the cutting temperature in drilling of cortical bone (P<0.05): the cutting temperature tended to decrease with increasing vibrational frequency and amplitude. The FEA results also showed that the vibrational amplitude holds a significant effect on the cutting heat conduction. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

Trace elements and rare earth elements in wet deposition of Lijiang, Mt. Yulong region, southeastern edge of the Tibetan Plateau.

Science.gov (United States)

Guo, Junming; Kang, Shichang; Huang, Jie; Sillanpää, Mika; Niu, Hewen; Sun, Xuejun; He, Yuanqing; Wang, Shijing; Tripathee, Lekhendra

2017-02-01

In order to investigate the compositions and wet deposition fluxes of trace elements and rare earth elements (REEs) in the precipitation of the southeastern edge of the Tibetan Plateau, 38 precipitation samples were collected from March to August in 2012 in an urban site of Lijiang city in the Mt. Yulong region. The concentrations of most trace elements and REEs were higher during the non-monsoon season than during the monsoon season, indicating that the lower concentrations of trace elements and REEs observed during monsoon had been influenced by the dilution effect of increased precipitation. The concentrations of trace elements in the precipitation of Lijiang city were slightly higher than those observed in remote sites of the Tibetan Plateau but much lower than those observed in the metropolises of China, indicating that the atmospheric environment of Lijiang city was less influenced by anthropogenic emissions, and, as a consequence, the air quality was still relatively good. However, the results of enrichment factor and principal component analysis revealed that some anthropogenic activities (e.g., the increasing traffic emissions from the rapid development of tourism) were most likely important contributors to trace elements, while the regional/local crustal sources rather than anthropogenic activities were the predominant contributors to the REEs in the wet deposition of Lijiang city. Our study was relevant not only for assessing the current status of the atmospheric environment in the Mt. Yulong region, but also for specific management actions to be implemented for the control of atmospheric inputs and the health of the environment for the future. Copyright © 2016. Published by Elsevier B.V.

Recent research on the heavy transuranium elements

International Nuclear Information System (INIS)

Seaborg, G.T.

1988-09-01

This review is devoted to recent research (performed in the 1980s) on the heavy members of the group, defined as the transcurium elements (with a few references to related work on lighter elements). It covers the discovery of the three heaviest elements, the discovery of new isotopes, investigation of interesting decay properties of some previously known isotopes, investigations of some heavy ion reaction mechanisms in this region, and recent investigations of nuclear and chemical properties. It is not exhaustive in its coverage, is necessarily succinct, and inevitably places emphasis on those aspects with which the author is most familiar. 92 refs., 3 figs

Investigation of microwave assisted drying of samples and evaporation of aqueous solutions in trace element analysis

Energy Technology Data Exchange (ETDEWEB)

Maichin, B.; Knapp, G. [Technische Univ., Graz (Austria). Inst. fuer Analytische Chemie, Mikro- und Radiochemie; Kettisch, P. [Anton Paar GmbH, Graz (Austria)

2000-01-01

Investigations of microwave assisted drying of sample materials and microwave assisted evaporation of aqueous sample solutions and acidic digestion residues were accomplished by means of special rotors for the microwave digestion system MULTIWAVE. To check the results obtained by microwave assisted drying, the samples were also conventionally dried at 105 C in an oven. The following samples have been dried: 10 g each of meat, fish, apple, cucumber, potato, mustard, yogurt, clay and marl; 1 g each of certified reference material TORT 2 (lobster hepatopancreas), BCR 278 (mussel tissue) and BCR 422 (cod muscle); 500 g garden mould. Microwave assisted drying takes 40 min for organic samples and 30 min for inorganic material. Important is a slow increase of microwave power during the first 20 min. The results agree well with conventional drying at 105 C. Losses of As, Se and Hg have been investigated for 3 CRMs. Only Se shows losses in the range of 20%. Losses of As, Be, Cd, Co, Cr, Cu, Fe, Hg, Li, Mg, Mn, Mo, Ni, Pb, Sb, Se, Sr, Ti, Tl, V and Zn after evaporation of aqueous samples and acidic solutions after wet digestion, respectively, have been investigated. 50 mL aqueous solution was evaporated almost to dryness within 25 min. The recovery of Hg is 40-50%, of Se 90-95% and of the other elements 97-102%. 0.2 g each of TORT 2, BCR 278 and BCR 422 have been digested with 4 mL nitric acid and 1 mL hydrochloric acid by means of the microwave digestion system MULTIWAVE. The digestion residue was evaporated almost to dryness and dissolved again in 10 mL diluted nitric acid. In this case no element losses have been observed. The measured concentration of As, Cd, Cu, Fe, Mn, Hg, Pb, Mo, Ni, Se, Sr, V and Zn agree very well with the certified values. An important prerequisite for good recoveries is not to evaporate the solutions to complete dryness. (orig.)

Provenance Establishment of Stingless Bee Honey Using Multi-element Analysis in Combination with Chemometrics Techniques.

Science.gov (United States)

Shadan, Aidil Fahmi; Mahat, Naji A; Wan Ibrahim, Wan Aini; Ariffin, Zaiton; Ismail, Dzulkiflee

2018-01-01

As consumption of stingless bee honey has been gaining popularity in many countries including Malaysia, ability to identify accurately its geographical origin proves pertinent for investigating fraudulent activities for consumer protection. Because a chemical signature can be location-specific, multi-element distribution patterns may prove useful for provenancing such product. Using the inductively coupled-plasma optical emission spectrometer as well as principal component analysis (PCA) and linear discriminant analysis (LDA), the distributions of multi-elements in stingless bee honey collected at four different geographical locations (North, West, East, and South) in Johor, Malaysia, were investigated. While cross-validation using PCA demonstrated 87.0% correct classification rate, the same was improved (96.2%) with the use of LDA, indicating that discrimination was possible for the different geographical regions. Therefore, utilization of multi-element analysis coupled with chemometrics techniques for assigning the provenance of stingless bee honeys for forensic applications is supported. © 2017 American Academy of Forensic Sciences.

Investigation of waste form materials suitable for immobilizing actinide elements in high-level waste

International Nuclear Information System (INIS)

Hayakawa, Issei; Kamizono, Hiroshi

1992-07-01

The microstructure of waste form materials suitable for immobilizing actinide elements can be classified into the following two categories. (1) Actinide elements are immobilized in an crystallized matrix after the formation of solid solution or compounds. (2) Actinide elements are immobilized in a durable material by encapsulation. Based on crystal chemistry, durability data, phase diagrams, compositions of natural minerals, eleven oxide compounds and one non-oxide compound are pointed out to be new candidates included in category (1). The other survey on material compositions, manufacturing conditions and feasibility shows that SiC, glassy carbon, ZrO 2 , Ti-O-Si-C ceramics are preferable matrix materials included in category (2). Polymers and fine powders are suitable as starting materials for the encapsulation of actinide elements because of their excellent sinterability. (author) 50 refs

Element-specific spectral imaging of multiple contrast agents: a phantom study

Science.gov (United States)

Panta, R. K.; Bell, S. T.; Healy, J. L.; Aamir, R.; Bateman, C. J.; Moghiseh, M.; Butler, A. P. H.; Anderson, N. G.

2018-02-01

This work demonstrates the feasibility of simultaneous discrimination of multiple contrast agents based on their element-specific and energy-dependent X-ray attenuation properties using a pre-clinical photon-counting spectral CT. We used a photon-counting based pre-clinical spectral CT scanner with four energy thresholds to measure the X-ray attenuation properties of various concentrations of iodine (9, 18 and 36 mg/ml), gadolinium (2, 4 and 8 mg/ml) and gold (2, 4 and 8 mg/ml) based contrast agents, calcium chloride (140 and 280 mg/ml) and water. We evaluated the spectral imaging performances of different energy threshold schemes between 25 to 82 keV at 118 kVp, based on K-factor and signal-to-noise ratio and ranked them. K-factor was defined as the X-ray attenuation in the K-edge containing energy range divided by the X-ray attenuation in the preceding energy range, expressed as a percentage. We evaluated the effectiveness of the optimised energy selection to discriminate all three contrast agents in a phantom of 33 mm diameter. A photon-counting spectral CT using four energy thresholds of 27, 33, 49 and 81 keV at 118 kVp simultaneously discriminated three contrast agents based on iodine, gadolinium and gold at various concentrations using their K-edge and energy-dependent X-ray attenuation features in a single scan. A ranking method to evaluate spectral imaging performance enabled energy thresholds to be optimised to discriminate iodine, gadolinium and gold contrast agents in a single spectral CT scan. Simultaneous discrimination of multiple contrast agents in a single scan is likely to open up new possibilities of improving the accuracy of disease diagnosis by simultaneously imaging multiple bio-markers each labelled with a nano-contrast agent.

Pathological Buying Online as a Specific Form of Internet Addiction: A Model-Based Experimental Investigation

Science.gov (United States)

Trotzke, Patrick; Starcke, Katrin; Müller, Astrid; Brand, Matthias

2015-01-01

The study aimed to investigate different factors of vulnerability for pathological buying in the online context and to determine whether online pathological buying has parallels to a specific Internet addiction. According to a model of specific Internet addiction by Brand and colleagues, potential vulnerability factors may consist of a predisposing excitability from shopping and as mediating variable, specific Internet use expectancies. Additionally, in line with models on addiction behavior, cue-induced craving should also constitute an important factor for online pathological buying. The theoretical model was tested in this study by investigating 240 female participants with a cue-reactivity paradigm, which was composed of online shopping pictures, to assess excitability from shopping. Craving (before and after the cue-reactivity paradigm) and online shopping expectancies were measured. The tendency for pathological buying and online pathological buying were screened with the Compulsive Buying Scale (CBS) and the Short Internet Addiction Test modified for shopping (s-IATshopping). The results demonstrated that the relationship between individual’s excitability from shopping and online pathological buying tendency was partially mediated by specific Internet use expectancies for online shopping (model’s R² = .742, p behavior merits potential consideration within the non-substance/behavioral addictions. PMID:26465593

Macrolide resistance gene erm(TR) and erm(TR)-carrying genetic elements in Streptococcus agalactiae: characterization of ICESagTR7, a new composite element containing IMESp2907.

Science.gov (United States)

Mingoia, Marina; Morici, Eleonora; Marini, Emanuela; Brenciani, Andrea; Giovanetti, Eleonora; Varaldo, Pietro E

2016-03-01

The objective of this study was to investigate macrolide-resistant Streptococcus agalactiae isolates harbouring erm(TR), an erm(A) gene subclass, with emphasis on their erm(TR)-carrying genetic elements. Four erm(TR)-carrying elements have been described to date: three closely related (ICE10750-RD.2, Tn1806 and ICESp1108) in Streptococcus pyogenes, Streptococcus pneumoniae and S. pyogenes, respectively; and one completely different (IMESp2907, embedded in ICESp2906 to form ICESp2905) in S. pyogenes. Seventeen macrolide-resistant erm(TR)-positive S. agalactiae isolates were phenotypically and genotypically characterized. Their erm(TR)-carrying elements were explored by analysing the distinctive recombination genes of known erm(TR)-carrying integrative and conjugative elements (ICEs) and by PCR mapping. The new genetic context and organization of IMESp2907 in S. agalactiae were explored using several experimental procedures and in silico analyses. Five isolates harboured ICE10750-RD.2/Tn1806, five isolates harboured ICESp1108 and five isolates bore unknown erm(TR)-carrying elements. The remaining two isolates, exhibiting identical serotypes and pulsotypes, harboured IMESp2907 in a new genetic environment, which was further investigated in one of the two isolates, SagTR7. IMESp2907 was circularizable in S. agalactiae, as described in S. pyogenes. The new IMESp2907 junctions were identified based on its site-specific integration; the att sites were almost identical to those in S. pyogenes. In strain SagTR7, erm(TR)-carrying IMESp2907 was embedded in an erm(TR)-less internal element related to ICE10750-RD.2/Tn1806, which, in turn, was embedded in an ICESde3396-like element. The resulting whole ICE, ICESagTR7 (∼129 kb), was integrated into the chromosome downstream of the rplL gene, and was excisable in circular form and transferable by conjugation. This is the first study exploring erm(TR)-carrying genetic elements in S. agalactiae. © The Author 2015. Published by

Finite element modeling of aponeurotomy: altered intramuscular myofascial force transmission yields complex sarcomere length distributions determining acute effects

NARCIS (Netherlands)

Yucesoy, C.A.; Koopman, Hubertus F.J.M.; Grootenboer, H.J.; Huijing, P.A.J.B.M.

2007-01-01

Finite element modeling of aponeurotomized rat extensor digitorium longus muscle was performed to investigate the acute effects of proximal aponeurotomy. The specific goal was to assess the changes in lengths of sarcomeres within aponeurotomized muscle and to explain how the intervention leads to

INVESTIGATION OF DYNAMIC CHARACTERISTICS OF ELEMENTS OF AUTOMATICS OF A SMART HOUSE IN PARAMETRICAL STRUCTURAL SCHEMES

Directory of Open Access Journals (Sweden)

Petrova Irina Yur’evna

2018-01-01

Full Text Available Subject: automation of calculation of dynamic characteristics of the device being designed in the system of conceptual design of sensor equipment, structurally-parametric models of dynamic processes and algorithms for the automated calculation of the qualitative characteristics of elements of the information-measuring and control systems (IMCS. The stage of conceptual design most fully determines the operational characteristics of technical systems. However, none of the information support systems of this stage provides an opportunity to evaluate the performance characteristics of the element being designed taking into account its dynamic characteristics. Research objectives: increasing the effectiveness of the evaluation of dynamic characteristics of sensitive elements of the information-measuring and control systems of a smart house. Materials and methods: when solving the problems posed, the mathematical apparatus of system modeling was used (in particular, the energy-information method of modeling processes of various physical nature that occur in the sensor equipment; the main provisions of the theory of automatic control, the theory of constructing computer-aided design systems, the theory of operational calculus; basics of conceptual design of elements of the information-measuring and control systems. Results: we compared the known automated systems for conceptual design of sensors, highlighted their advantages and disadvantages and we showed that none of these systems allows us to investigate dynamic characteristics of the element being designed in a simple and understandable for engineer form. The authors proposed using energy-information method of modeling for the synthesis of operation principles of sensors and analysis of their dynamic characteristics. We considered elementary dynamic chains and issues of synthesis of parametrical structural schemes that reflect the dynamics of the process with the use of mathematical apparatus of

Primary stability of a cementless acetabular cup in a cohort of patient-specific finite element models.

Science.gov (United States)

O'Rourke, Dermot; Al-Dirini, Rami Ma; Taylor, Mark

2018-03-01

The primary stability achieved during total hip arthroplasty determines the long-term success of cementless acetabular cups. Pre-clinical finite element testing of cups typically use a model of a single patient and assume the results can be extrapolated to the general population. This study explored the variability in predicted primary stability of a Pinnacle ® cementless acetabular cup in 103 patient-specific finite element models of the hemipelvis and examined the association between patient-related factors and the observed variability. Cups were inserted by displacement-control into the FE models and then a loading configuration simulating a complete level gait cycle was applied. The cohort showed a range of polar gap of 284-1112 μm and 95th percentile composite peak micromotion (CPM) of 18-624 μm. Regression analysis was not conclusive on the relationship between patient-related factors and primary stability. No relationship was found between polar gap and micromotion. However, when the patient-related factors were categorised into quartile groups, trends suggested higher polar gaps occurred in subjects with small and shallow acetabular geometries and cup motion during gait was affected most by low elastic modulus and high bodyweight. The variation in primary stability in the cohort for an acetabular cup with a proven clinical track record may provide benchmark data when evaluating new cup designs. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 36:1012-1023, 2018. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

PEG Functionalization of Whispering Gallery Mode Optical Microresonator Biosensors to Minimize Non-Specific Adsorption during Targeted, Label-Free Sensing

Directory of Open Access Journals (Sweden)

Fanyongjing Wang

2015-07-01

Full Text Available Whispering Gallery Mode (WGM optical microresonator biosensors are a powerful tool for targeted detection of analytes at extremely low concentrations. However, in complex environments, non-specific adsorption can significantly reduce their signal to noise ratio, limiting their accuracy. To overcome this, poly(ethylene glycol (PEG can be employed in conjunction with appropriate recognition elements to create a nonfouling surface capable of detecting targeted analytes. This paper investigates a general route for the addition of nonfouling elements to WGM optical biosensors to reduce non-specific adsorption, while also retaining high sensitivity. We use the avidin-biotin analyte-recognition element system, in conjunction with PEG nonfouling elements, as a proof-of-concept, and explore the extent of non-specific adsorption of lysozyme and fibrinogen at multiple concentrations, as well as the ability to detect avidin in a concentration-dependent fashion. Ellipsometry, contact angle measurement, fluorescence microscopy, and optical resonator characterization methods were used to study non-specific adsorption, the quality of the functionalized surface, and the biosensor’s performance. Using a recognition element ratio to nonfouling element ratio of 1:1, we showed that non-specific adsorption could be significantly reduced over the controls, and that high sensitivity could be maintained. Due to the frequent use of biotin-avidin-biotin sandwich complexes in functionalizing sensor surfaces with biotin-labeled recognition elements, this chemistry could provide a common basis for creating a non-fouling surface capable of targeted detection. This should improve the ability of WGM optical biosensors to operate in complex environments, extending their application towards real-world detection.

Cooperative action of multiple cis-acting elements is required for N-myc expression in branchial arches: specific contribution of GATA3.

Science.gov (United States)

Potvin, Eric; Beuret, Laurent; Cadrin-Girard, Jean-François; Carter, Marcelle; Roy, Sophie; Tremblay, Michel; Charron, Jean

2010-11-01

The precise expression of the N-myc proto-oncogene is essential for normal mammalian development, whereas altered N-myc gene regulation is known to be a determinant factor in tumor formation. Using transgenic mouse embryos, we show that N-myc sequences from kb -8.7 to kb +7.2 are sufficient to reproduce the N-myc embryonic expression profile in developing branchial arches and limb buds. These sequences encompass several regulatory elements dispersed throughout the N-myc locus, including an upstream limb bud enhancer, a downstream somite enhancer, a branchial arch enhancer in the second intron, and a negative regulatory element in the first intron. N-myc expression in the limb buds is under the dominant control of the limb bud enhancer. The expression in the branchial arches necessitates the interplay of three regulatory domains. The branchial arch enhancer cooperates with the somite enhancer region to prevent an inhibitory activity contained in the first intron. The characterization of the branchial arch enhancer has revealed a specific role of the transcription factor GATA3 in the regulation of N-myc expression. Together, these data demonstrate that correct N-myc developmental expression is achieved via cooperation of multiple positive and negative regulatory elements.

Mechanical properties investigation on single-wall ZrO2 nanotubes: A finite element method with equivalent Poisson's ratio for chemical bonds

Science.gov (United States)

Yang, Xiao; Li, Huijian; Hu, Minzheng; Liu, Zeliang; Wärnå, John; Cao, Yuying; Ahuja, Rajeev; Luo, Wei

2018-04-01

A method to obtain the equivalent Poisson's ratio in chemical bonds as classical beams with finite element method was proposed from experimental data. The UFF (Universal Force Field) method was employed to calculate the elastic force constants of Zrsbnd O bonds. By applying the equivalent Poisson's ratio, the mechanical properties of single-wall ZrNTs (ZrO2 nanotubes) were investigated by finite element analysis. The nanotubes' Young's modulus (Y), Poisson's ratio (ν) of ZrNTs as function of diameters, length and chirality have been discussed, respectively. We found that the Young's modulus of single-wall ZrNTs is calculated to be between 350 and 420 GPa.

Comparison of computed tomography based parametric and patient-specific finite element models of the healthy and metastatic spine using a mesh-morphing algorithm.

Science.gov (United States)

O'Reilly, Meaghan Anne; Whyne, Cari Marisa

2008-08-01

A comparative analysis of parametric and patient-specific finite element (FE) modeling of spinal motion segments. To develop patient-specific FE models of spinal motion segments using mesh-morphing methods applied to a parametric FE model. To compare strain and displacement patterns in parametric and morphed models for both healthy and metastatically involved vertebrae. Parametric FE models may be limited in their ability to fully represent patient-specific geometries and material property distributions. Generation of multiple patient-specific FE models has been limited because of computational expense. Morphing methods have been successfully used to generate multiple specimen-specific FE models of caudal rat vertebrae. FE models of a healthy and a metastatic T6-T8 spinal motion segment were analyzed with and without patient-specific material properties. Parametric and morphed models were compared using a landmark-based morphing algorithm. Morphing of the parametric FE model and including patient-specific material properties both had a strong impact on magnitudes and patterns of vertebral strain and displacement. Small but important geometric differences can be represented through morphing of parametric FE models. The mesh-morphing algorithm developed provides a rapid method for generating patient-specific FE models of spinal motion segments.

Exact and approximate exchange potentials investigated in terms of their matrix elements with the Kohn-Sham orbitals

International Nuclear Information System (INIS)

Holas, A.; Cinal, M.

2005-01-01

Three approximate exchange potentials of high accuracy v x Y (r), Y=A,B,C, for the density-functional theory applications are obtained by replacing the matrix elements of the exact potential between the Kohn-Sham (KS) orbitals with such elements of the Fock exchange operator (within the virtual-occupied subset only) in three representations found for any local potential. A common identity is the base of these representations. The potential v x C happens to be the same as that derived by Harbola and Sahni, and v x A as that derived by Gritsenko and Baerends, and Della Sala and Goerling. The potentials obtained can be expressed in terms of occupied KS orbitals only. At large r, their asymptotic form -1/r is the same as that of the exact potential. The high quality of these three approximations is demonstrated by direct comparison with the exact potential and using various consistency tests. A common root established for the three approximations could be helpful in finding new and better approximations via modification of identities employed in the present investigation

Efficient finite element modelling for the investigation of the dynamic behaviour of a structure with bolted joints

Science.gov (United States)

Omar, R.; Rani, M. N. Abdul; Yunus, M. A.; Mirza, W. I. I. Wan Iskandar; Zin, M. S. Mohd

2018-04-01

A simple structure with bolted joints consists of the structural components, bolts and nuts. There are several methods to model the structures with bolted joints, however there is no reliable, efficient and economic modelling methods that can accurately predict its dynamics behaviour. Explained in this paper is an investigation that was conducted to obtain an appropriate modelling method for bolted joints. This was carried out by evaluating four different finite element (FE) models of the assembled plates and bolts namely the solid plates-bolts model, plates without bolt model, hybrid plates-bolts model and simplified plates-bolts model. FE modal analysis was conducted for all four initial FE models of the bolted joints. Results of the FE modal analysis were compared with the experimental modal analysis (EMA) results. EMA was performed to extract the natural frequencies and mode shapes of the test physical structure with bolted joints. Evaluation was made by comparing the number of nodes, number of elements, elapsed computer processing unit (CPU) time, and the total percentage of errors of each initial FE model when compared with EMA result. The evaluation showed that the simplified plates-bolts model could most accurately predict the dynamic behaviour of the structure with bolted joints. This study proved that the reliable, efficient and economic modelling of bolted joints, mainly the representation of the bolting, has played a crucial element in ensuring the accuracy of the dynamic behaviour prediction.

LOD BIM Element specification for Railway Turnout Systems Risk Mitigation using the Information Delivery Manual

Science.gov (United States)

Gigante-Barrera, Ángel; Dindar, Serdar; Kaewunruen, Sakdirat; Ruikar, Darshan

2017-10-01

Railway turnouts are complex systems designed using complex geometries and grades which makes them difficult to be managed in terms of risk prevention. This feature poses a substantial peril to rail users as it is considered a cause of derailment. In addition, derailment deals to financial losses due to operational downtimes and monetary compensations in case of death or injure. These are fundamental drivers to consider mitigating risks arising from poor risk management during design. Prevention through design (PtD) is a process that introduces tacit knowledge from industry professionals during the design process. There is evidence that Building Information Modelling (BIM) can help to mitigate risk since the inception of the project. BIM is considered an Information System (IS) were tacit knowledge can be stored and retrieved from a digital database making easy to take promptly decisions as information is ready to be analysed. BIM at the model element level entails working with 3D elements and embedded data, therefore adding a layer of complexity to the management of information along the different stages of the project and across different disciplines. In order to overcome this problem, the industry has created a framework for model progression specification named Level of Development (LOD). The paper presents an IDM based framework for design risk mitigation through code validation using the LOD. This effort resulted on risk datasets which describe graphically and non-graphically a rail turnout as the model progresses. Thus, permitting its inclusion within risk information systems. The assignment of an LOD construct to a set of data, requires specialised management and process related expertise. Furthermore, the selection of a set of LOD constructs requires a purpose based analysis. Therefore, a framework for LOD constructs implementation within the IDM for code checking is required for the industry to progress in this particular field.

A real-time PCR assay with improved specificity for detection and discrimination of all clinically relevant Bordetella species by the presence and distribution of three Insertion Sequence elements

Directory of Open Access Journals (Sweden)

Ossewaarde Jacobus M

2011-01-01

Full Text Available Abstract Background In Dutch laboratories molecular detection of B. pertussis and B. parapertussis is commonly based on insertion sequences IS481 and IS1001, respectively. Both IS elements are more widely spread among Bordetella species. Both Bordetella holmesii, and B. bronchiseptica can harbour IS481. Also, IS1001 is found among B. bronchiseptica. IS481, and IS1001 based PCR thus lacks specificity when used for detection of specific Bordetella spp. Findings We designed a PCR based on IS1002, another IS element that is present among Bordetella species, and exploited it as a template in combination with PCR for IS481, and IS1001. In combining the PCRs for IS481, IS1001, and IS1002, and including an inhibition control, we were able to detect and discriminate all clinically relevant Bordetella species. Conclusions We developed an improved PCR method for specific detection of B. pertussis, B. parapertussis, B. holmesii, and B. bronchiseptica.

An Investigation Into the Navy Public Works Centers Specific Work Service Processing Problems.

Science.gov (United States)

1980-12-01

complex interface of all the elements of individual and organizational behavior. These elements include leadership , motivation, productivity, group...site; variances: nzineering; d. iob control: (ield leadership ; emploYee attitudes; accurac’: or estimates e. and 4ob olans "no problems". 31. Are...indica-ed prcvidinz -he hesr re3s. e I.nck -a- situation or thoughts. The "you" in -.- Il -r your organizatinal element in genera-, .-nis Jn multipie

Numerical investigation of shape domain effect to its elasticity and surface energy using adaptive finite element method

Science.gov (United States)

Alfat, Sayahdin; Kimura, Masato; Firihu, Muhammad Zamrun; Rahmat

2018-05-01

In engineering area, investigation of shape effect in elastic materials was very important. It can lead changing elasticity and surface energy, and also increase of crack propagation in the material. A two-dimensional mathematical model was developed to investigation of elasticity and surface energy in elastic material by Adaptive Finite Element Method. Besides that, behavior of crack propagation has observed for every those materials. The government equations were based on a phase field approach in crack propagation model that developed by Takaishi-Kimura. This research has varied four shape domains where physical properties of materials were same (Young's modulus E = 70 GPa and Poisson's ratio ν = 0.334). Investigation assumptions were; (1) homogeneous and isotropic material, (2) there was not initial cracking at t = 0, (3) initial displacement was zero [u1, u2] = 0) at initial condition (t = 0), and (4) length of time simulation t = 5 with interval Δt = 0.005. Mode I/II or mixed mode crack propagation has been used for the numerical investigation. Results of this studies were very good and accurate to show changing energy and behavior of crack propagation. In the future time, this research can be developed to complex phenomena and domain. Furthermore, shape optimization can be investigation by the model.

Source-pathway-receptor investigation of the fate of trace elements derived from shotgun pellets discharged in terrestrial ecosystems managed for game shooting

International Nuclear Information System (INIS)

Sneddon, Jennifer; Clemente, Rafael; Riby, Philip; Lepp, Nicholas W.

2009-01-01

Spent shotgun pellets may contaminate terrestrial ecosystems. We examined the fate of elements originating from shotgun pellets in pasture and woodland ecosystems. Two source-receptor pathways: i) soil-soil pore water-plant and ii) whole earthworm/worm gut contents - washed and unwashed small mammal hair were investigated. Concentrations of Pb and associated contaminants were higher in soils from shot areas than controls. Arsenic and lead concentrations were positively correlated in soils, soil pore water and associated biota. Element concentrations in biota were below statutory levels in all locations. Bioavailability of lead to small mammals, based on concentrations in washed body hair was low. Lead movement from soil water to higher trophic levels was minor compared to lead adsorbed onto body surfaces. Lead was concentrated in earthworm gut and some plants. Results indicate that managed game shooting presents minimal risk in terms of element transfer to soils and their associated biota. - Source-receptor pathway analysis of a managed game shooting site showed no environmental risk of trace element transfer.

Source-pathway-receptor investigation of the fate of trace elements derived from shotgun pellets discharged in terrestrial ecosystems managed for game shooting

Energy Technology Data Exchange (ETDEWEB)

Sneddon, Jennifer [School of Natural Sciences and Psychology, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom); Clemente, Rafael, E-mail: rclemente@cebas.csic.e [School of Natural Sciences and Psychology, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom); Riby, Philip [School of Pharmacy and Chemistry, Liverpool John Moores University, Liverpool L3 3AF (United Kingdom); Lepp, Nicholas W., E-mail: n.w.lepp@ljmu.ac.u [School of Natural Sciences and Psychology, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom)

2009-10-15

Spent shotgun pellets may contaminate terrestrial ecosystems. We examined the fate of elements originating from shotgun pellets in pasture and woodland ecosystems. Two source-receptor pathways: i) soil-soil pore water-plant and ii) whole earthworm/worm gut contents - washed and unwashed small mammal hair were investigated. Concentrations of Pb and associated contaminants were higher in soils from shot areas than controls. Arsenic and lead concentrations were positively correlated in soils, soil pore water and associated biota. Element concentrations in biota were below statutory levels in all locations. Bioavailability of lead to small mammals, based on concentrations in washed body hair was low. Lead movement from soil water to higher trophic levels was minor compared to lead adsorbed onto body surfaces. Lead was concentrated in earthworm gut and some plants. Results indicate that managed game shooting presents minimal risk in terms of element transfer to soils and their associated biota. - Source-receptor pathway analysis of a managed game shooting site showed no environmental risk of trace element transfer.

Discovery of element 112

Energy Technology Data Exchange (ETDEWEB)

Hofmann, S. [GSI, Darmstadt (Germany)

1996-12-31

The new elements 110, 111, and 112 were synthesized and unambiguously identified in experiments at SHIP. Due to strong shell effects the dominant decay mode is not fission, but emission of alpha particles. Theoretical investigations predict that maximum shell effects should exist in nuclei near proton number 114 and neutron number 184. Measurements give hope that isotopes of element 114 close to the island of spherical Superheavy Elements could be produced by fusion reactions using {sup 118}Pb as target. systematic studies of the reaction cross-sections indicate that transfer of nucleons is the important process to initiate the fusion.

Study of Superheavy Elements

International Nuclear Information System (INIS)

Hofmann, Sigurd

2007-01-01

The nuclear shell model predicts that the next doubly magic shell-closure beyond 208 Pb is at a proton number Z = 114, 120, or 126 and at a neutron number N = 172 or 184. The outstanding aim of experimental investigations is the exploration of this region of spherical 'SuperHeavy Elements' (SHEs). Experimental methods are described, which allowed for the identification of elements produced on a cross-section level of about 1 pb. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission, not fission. Decay properties as well as reaction cross-sections are compared with results of theoretical investigations. Finally, plans are presented for the further development of the experimental set-up and the application of new techniques, as for instance the precise mass measurement of the produced nuclei using ion traps. At increased sensitivity, the detailed exploration of the region of spherical SHEs will start, after first steps on the island were made in recent years. (Author)

Transcriptional activity of transposable elements in coelacanth.

Science.gov (United States)

Forconi, Mariko; Chalopin, Domitille; Barucca, Marco; Biscotti, Maria Assunta; De Moro, Gianluca; Galiana, Delphine; Gerdol, Marco; Pallavicini, Alberto; Canapa, Adriana; Olmo, Ettore; Volff, Jean-Nicolas

2014-09-01

The morphological stasis of coelacanths has long suggested a slow evolutionary rate. General genomic stasis might also imply a decrease of transposable elements activity. To evaluate the potential activity of transposable elements (TEs) in "living fossil" species, transcriptomic data of Latimeria chalumnae and its Indonesian congener Latimeria menadoensis were compared through the RNA-sequencing mapping procedures in three different organs (liver, testis, and muscle). The analysis of coelacanth transcriptomes highlights a significant percentage of transcribed TEs in both species. Major contributors are LINE retrotransposons, especially from the CR1 family. Furthermore, some particular elements such as a LF-SINE and a LINE2 sequences seem to be more expressed than other elements. The amount of TEs expressed in testis suggests possible transposition burst in incoming generations. Moreover, significant amount of TEs in liver and muscle transcriptomes were also observed. Analyses of elements displaying marked organ-specific expression gave us the opportunity to highlight exaptation cases, that is, the recruitment of TEs as new cellular genes, but also to identify a new Latimeria-specific family of Short Interspersed Nuclear Elements called CoeG-SINEs. Overall, transcriptome results do not seem to be in line with a slow-evolving genome with poor TE activity. © 2013 Wiley Periodicals, Inc.

High resolution bone material property assignment yields robust subject specific finite element models of complex thin bone structures.

Science.gov (United States)

Pakdel, Amirreza; Fialkov, Jeffrey; Whyne, Cari M

2016-06-14

Accurate finite element (FE) modeling of complex skeletal anatomy requires high resolution in both meshing and the heterogeneous mapping of material properties onto the generated mesh. This study introduces Node-based elastic Modulus Assignment with Partial-volume correction (NMAP) as a new approach for FE material property assignment to thin bone structures. The NMAP approach incorporates point spread function based deblurring of CT images, partial-volume correction of CT image voxel intensities and anisotropic interpolation and mapping of CT intensity assignment to FE mesh nodes. The NMAP procedure combined with a derived craniomaxillo-facial skeleton (CMFS) specific density-isotropic elastic modulus relationship was applied to produce specimen-specific FE models of 6 cadaveric heads. The NMAP procedure successfully generated models of the complex thin bone structures with surface elastic moduli reflective of cortical bone material properties. The specimen-specific CMFS FE models were able to accurately predict experimental strains measured under in vitro temporalis and masseter muscle loading (r=0.93, slope=1.01, n=5). The strength of this correlation represents a robust validation for CMFS FE modeling that can be used to better understand load transfer in this complex musculoskeletal system. The developed methodology offers a systematic process-flow able to address the complexity of the CMFS that can be further applied to create high-fidelity models of any musculoskeletal anatomy. Copyright © 2016 Elsevier Ltd. All rights reserved.

The General Laws of Chemical Elements Composition Dynamics in the Biosphere

Science.gov (United States)

Korzh, Vyacheslav D.

2013-04-01

The key point of investigation of the specificity of the biosphere elemental composition formation is determination of patterns of redistribution of elemental average concentrations among various phases, like solid - liquid ( the lithosphere - the hydrosphere), which occurs as a result of a global continuous processing of inert matter by living substances. Our task here is to investigate this process in the system "lithosphere - hydrosphere" in view of the integrated involvement of living material in it. This process is most active in biogeochemical barriers, i.e. in places of "the life condensation" and runs under a nonlinear regularity that has been unknown before. It is established that this process results in a general relative increase in concentrations of chemical elements in the solid phase in proportion as their prevalence in the environment is reduced. This process running in various natural systems has practically the same parameter of nonlinearity (v) approximately equal to 0.7. For proto-lithosphere -"living material" - soil v = 0.75. For river - "living material" - ocean v = 0.67. For the contemporary factual awareness level these estimations of nonlinearity indices are practically negligible. Hence, it is for the first time that the existence of a universal constant of nonlinearity of elemental composition evolution in the biosphere has been proved and its quantitative evaluation has been made. REFERENCES 1. Korzh V.D. 1974. Some general laws governing the turnover of substance within the ocean-atmosphere-continent-ocean cycle. // Journal de Recherches Atmospheriques. Vol. 8. P. 653-660. 2. Korzh V.D. 2008. The general laws in the formation of the elemental composition of the Hydrosphere and Biosphere.// J. Ecologica, Vol. XV, P. 13-21. 3. Korzh V.D. 2012. Determination of general laws of elemental composition in Hydrosphere // Water: chemistry & ecology, Journal of water science and its practical application. # 1, P.56-62.

Diffractive optical elements for space communication terminals

OpenAIRE

Herzig, Hans-Peter; Ehbets, Peter; Teijido, Juan M.; Weible, Kenneth J.; Heimbeck, Hans-Joerg

2007-01-01

The potential of diffractive optical elements for advanced laser communication terminals has been investigated. Applications include beam shaping of high- power laser diode arrays, optical filter elements for position detection and hybrid (refractive/diffractive) elements. In addition, we present a design example of a miniaturized terminal including diffractive optics.

Cell-type-specific enrichment of risk-associated regulatory elements at ovarian cancer susceptibility loci.

Science.gov (United States)

Coetzee, Simon G; Shen, Howard C; Hazelett, Dennis J; Lawrenson, Kate; Kuchenbaecker, Karoline; Tyrer, Jonathan; Rhie, Suhn K; Levanon, Keren; Karst, Alison; Drapkin, Ronny; Ramus, Susan J; Couch, Fergus J; Offit, Kenneth; Chenevix-Trench, Georgia; Monteiro, Alvaro N A; Antoniou, Antonis; Freedman, Matthew; Coetzee, Gerhard A; Pharoah, Paul D P; Noushmehr, Houtan; Gayther, Simon A

2015-07-01

Understanding the regulatory landscape of the human genome is a central question in complex trait genetics. Most single-nucleotide polymorphisms (SNPs) associated with cancer risk lie in non-protein-coding regions, implicating regulatory DNA elements as functional targets of susceptibility variants. Here, we describe genome-wide annotation of regions of open chromatin and histone modification in fallopian tube and ovarian surface epithelial cells (FTSECs, OSECs), the debated cellular origins of high-grade serous ovarian cancers (HGSOCs) and in endometriosis epithelial cells (EECs), the likely precursor of clear cell ovarian carcinomas (CCOCs). The regulatory architecture of these cell types was compared with normal human mammary epithelial cells and LNCaP prostate cancer cells. We observed similar positional patterns of global enhancer signatures across the three different ovarian cancer precursor cell types, and evidence of tissue-specific regulatory signatures compared to non-gynecological cell types. We found significant enrichment for risk-associated SNPs intersecting regulatory biofeatures at 17 known HGSOC susceptibility loci in FTSECs (P = 3.8 × 10(-30)), OSECs (P = 2.4 × 10(-23)) and HMECs (P = 6.7 × 10(-15)) but not for EECs (P = 0.45) or LNCaP cells (P = 0.88). Hierarchical clustering of risk SNPs conditioned on the six different cell types indicates FTSECs and OSECs are highly related (96% of samples using multi-scale bootstrapping) suggesting both cell types may be precursors of HGSOC. These data represent the first description of regulatory catalogues of normal precursor cells for different ovarian cancer subtypes, and provide unique insights into the tissue specific regulatory variation with respect to the likely functional targets of germline genetic susceptibility variants for ovarian cancer. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Hybrid Discrete Element - Finite Element Simulation for Railway Bridge-Track Interaction

Science.gov (United States)

Kaewunruen, S.; Mirza, O.

2017-10-01

At the transition zone or sometimes called ‘bridge end’ or ‘bridge approach’, the stiffness difference between plain track and track over bridge often causes aggravated impact loading due to uneven train movement onto the area. The differential track settlement over the transition has been a classical problem in railway networks, especially for the aging rail infrastructures around the world. This problem is also additionally worsened by the fact that the construction practice over the area is difficult, resulting in a poor compaction of formation and subgrade. This paper presents an advanced hybrid simulation using coupled discrete elements and finite elements to investigate dynamic interaction at the transition zone. The goal is to evaluate the dynamic stresses and to better understand the impact dynamics redistribution at the bridge end. An existing bridge ‘Salt Pan Creek Railway Bridge’, located between Revesby and Kingsgrove, has been chosen for detailed investigation. The Salt Pan Bridge currently demonstrates crushing of the ballast causing significant deformation and damage. Thus, it’s imperative to assess the behaviours of the ballast under dynamic loads. This can be achieved by modelling the nonlinear interactions between the steel rail and sleeper, and sleeper to ballast. The continuum solid elements of track components have been modelled using finite element approach, while the granular media (i.e. ballast) have been simulated by discrete element method. The hybrid DE/FE model demonstrates that ballast experiences significant stresses at the contacts between the sleeper and concrete section. These overburden stress exists in the regions below the outer rails, identify fouling and permanent deformation of the ballast.

Carbon and nitrogen elemental and isotopic ratios of filter-feeding bivalves along the French coasts: An assessment of specific, geographic, seasonal and multi-decadal variations.

Science.gov (United States)

Briant, Nicolas; Savoye, Nicolas; Chouvelon, Tiphaine; David, Valérie; Rodriguez, Samuel; Charlier, Karine; Sonke, Jeroen E; Chiffoleau, Jean François; Brach-Papa, Christophe; Knoery, Joël

2018-02-01

Primary consumers play a key role in coastal ecosystems by transferring organic matter from primary producers to predators. Among them, suspension-feeders, like bivalve molluscs are widely used in trophic web studies. The main goal of this study was to investigate variations of C and N elemental and isotopic ratios in common bivalves (M. edulis, M. galloprovincialis, and C. gigas) at large spatial (i.e. among three coastal regions) and different temporal (i.e. from seasonal to multi-decadal) scales in France, in order to identify potential general or specific patterns and speculate on their drivers. The observed spatial variability was related to the trophic status of the coastal regions (oligotrophic Mediterranean Sea versus meso- to eutrophic English Channel and Atlantic ocean), but not to ecosystem typology (estuaries, versus lagoons versus bays versus littoral systems). Furthermore, it highlighted local specificities in terms of the origin of the POM assimilated by bivalves (e.g., mainly continental POM vs. marine phytoplankton vs. microphytobenthic algae). Likewise, seasonal variability was related both to the reproduction cycle for C/N ratios of Mytilus spp. and to changes in trophic resources for δ 13 C of species located close to river mouth. Multi-decadal evolution exhibited shifts and trends for part of the 30-year series with decreases in δ 13 C and δ 15 N. Specifically, shifts appeared in the early 2000's, likely linking bivalve isotopic ratios to a cascade of processes affected by local drivers. Copyright © 2017 Elsevier B.V. All rights reserved.

Chemistry of the transactinide elements

International Nuclear Information System (INIS)

Schaedel, M.

1995-01-01

The experimentally known chemical properties of the transactinide elements 104 and 105, and the experimental techniques used to study these properties on an atom-at-a-time base, are reviewed. The production of transactinides in heavy ion reactions and the specific aspects of chemical separations with single atoms is briefly discussed. The chemical properties of the first two transactinide elements are compared with the lighter element homologs in group 4 and 5 of the Periodic Table and with the expected behaviour obtained from most recent atomic and molecular calculations which take the increasingly strong relativistic effect into account. Elements 104 and 105 behave as transactinide elements and, in general, exhibit properties characteristic of their position in group 4 and 5 of the Periodic Table. However, surprising deviations of the chemical properties from expectations based on simple extrapolations have been observed. It is shown that the chemical properties of the heaviest elements cannot reliably be predicted by simple extrapolations. Prospects to extend our chemical knowledge at the top end of the Periodic Table are discussed. (orig.)

The High Rise Low Cost Housing : Sustainable Neighbourhood Elements (Green Elements) in Malaysia

Science.gov (United States)

Wahi, Noraziah; Mohamad, Ismail; Mohamad Zin, Rosli; Munikanan, Vikneswaran; Junaini, Syahrizan

2018-03-01

The sustainable development is a vital measure to alleviate the greenhouse gas effect, global warming and any other environment issues. The sustainable neighbourhood concept is not new in Malaysia, However, the concept still needs attention and awareness from the stakeholders. This paper discusses on the sustainable neighbourhood elements specifically green elements application on the high rise low cost housing in Malaysia. Malaysia should have focused sustainable neighbourhood planning and design especially on the high rise low cost housing therefore the future generation can be benefited from this type development.

The evolution of ultraconserved elements with different phylogenetic origins

KAUST Repository

Ryu, Tae Woo

2012-12-05

Background: Ultraconserved elements of DNA have been identified in vertebrate and invertebrate genomes. These elements have been found to have diverse functions, including enhancer activities in developmental processes. The evolutionary origins and functional roles of these elements in cellular systems, however, have not yet been determined. Results: Here, we identified a wide range of ultraconserved elements common to distant species, from primitive aquatic organisms to terrestrial species with complicated body systems, including some novel elements conserved in fruit fly and human. In addition to a well-known association with developmental genes, these DNA elements have a strong association with genes implicated in essential cell functions, such as epigenetic regulation, apoptosis, detoxification, innate immunity, and sensory reception. Interestingly, we observed that ultraconserved elements clustered by sequence similarity. Furthermore, species composition and flanking genes of clusters showed lineage-specific patterns. Ultraconserved elements are highly enriched with binding sites to developmental transcription factors regardless of how they cluster. Conclusion: We identified large numbers of ultraconserved elements across distant species. Specific classes of these conserved elements seem to have been generated before the divergence of taxa and fixed during the process of evolution. Our findings indicate that these ultraconserved elements are not the exclusive property of higher modern eukaryotes, but rather transmitted from their metazoan ancestors. 2012 Ryu et al.; licensee BioMed Central Ltd.

Photoshop Elements 5 The Missing Manual

CERN Document Server

Brundage, Barbara

2006-01-01

Anyone still think that Adobe Photoshop Elements is a toy version of the real thing? As the most popular photo-editing program on the market, Photoshop Elements not only has Photoshop's marvelous powers, but also has capabilities the mothership lacks. Each new version includes more tools designed specifically for today's consumer digital photo enthusiasts. The latest edition, Photoshop Elements 5, solidifies the reputation of this superb and inexpensive product with new scrapbook features, a link to online photo services, and many other improvements. In fact, there's so much to Photoshop Ele

Automated Fuel Element Closure Welding System

International Nuclear Information System (INIS)

Wahlquist, D.R.

1993-01-01

The Automated Fuel Element Closure Welding System is a robotic device that will load and weld top end plugs onto nuclear fuel elements in a highly radioactive and inert gas environment. The system was developed at Argonne National Laboratory-West as part of the Fuel Cycle Demonstration. The welding system performs four main functions, it (1) injects a small amount of a xenon/krypton gas mixture into specific fuel elements, and (2) loads tiny end plugs into the tops of fuel element jackets, and (3) welds the end plugs to the element jackets, and (4) performs a dimensional inspection of the pre- and post-welded fuel elements. The system components are modular to facilitate remote replacement of failed parts. The entire system can be operated remotely in manual, semi-automatic, or fully automatic modes using a computer control system. The welding system is currently undergoing software testing and functional checkout

Ecosystem element transport model for Lake Eckarfjaerden

Energy Technology Data Exchange (ETDEWEB)

Konovalenko, L.; Bradshaw, C. [The Department of Ecology, Environment and Plant Sciences, Stockholm University (Sweden); Andersson, E.; Kautsky, U. [Swedish Nuclear Fuel and Waste Management Co. - SKB (Sweden)

2014-07-01

The ecosystem transport model of elements was developed for Lake Eckarfjaerden located in the Forsmark area in Sweden. Forsmark has currently a low level repository (SFR) and a repository for spent fuel is planned. A large number of data collected during site-investigation program 2002-2009 for planning the repository were available for the creation of the compartment model based on carbon circulation, physical and biological processes (e.g. primary production, consumption, respiration). The model is site-specific in the sense that the food web model is adapted to the actual food web at the site, and most estimates of biomass and metabolic rates for the organisms and meteorological data originate from site data. The functional organism groups of Lake Eckarfjaerden were considered as separate compartments: bacterio-plankton, benthic bacteria, macro-algae, phytoplankton, zooplankton, fish, benthic fauna. Two functional groups of bacteria were taken into account for the reason that they have the highest biomass of all functional groups during the winter, comprising 36% of the total biomass. Effects of ecological parameters, such as bacteria and algae biomass, on redistribution of a hypothetical radionuclide release in the lake were examined. The ecosystem model was used to estimate the environmental transfer of several elements (U, Th, Ra) and their isotopes (U-238, U-234,Th-232, Ra-226) to various aquatic organisms in the lake, using element-specific distribution coefficients for suspended particle and sediment. Results of chemical analyses of the water, sediment and biota were used for model validation. The model gives estimates of concentration factors for fish based on modelling rather on in situ measurement, which reduces the uncertainties for many radionuclides with scarce of data. Document available in abstract form only. (authors)

Investigation of HF-plasma-treated soft x-ray optical elements

Science.gov (United States)

Eggenstein, F.; Krivenkov, M.; Rudolph, I.; Sertsu, M. G.; Sokolov, A.; Varykhalov, A.; Wolf, J.; Zeschke, T.; Schäfers, F.

2017-09-01

The contamination of optical elements (mirrors and gratings) with carbon still is an issue when using soft x-ray synchrotron radiation. With an in-house developed HF-plasma treatment we are able to decontaminate our optics in-situ from carbon very efficiently. The cleaning device, a simple Al-antenna, is mounted in situ inside the mirror- and grating vacuum chambers. A systematic study of the HF-plasma cleaning efficiency was performed acquired with in-situ and exsitu methods for monitoring: An atomic force microscope (AFM) and a scanning tunneling microscope (STM) were used before and after the cleaning process to determine the surface morphology and roughness. Reflectivity angular scans using the reflectometer at the BESSY-II Metrology Station [1-3] allowed to estimate the thickness of the remaining Clayer after different cleaning steps and thereby helped us to determine the etching rate. Reflection spectra measurements in the range of 200 eV - 900 eV show the complete removal of Carbon from the optics without contaminating it with any other elements due to the plasma treatment. The data show that the plasma process improves the reflectivity and reduces the roughness of the surface. In addition to that, the region of the optical surface where the carbon has been removed becomes passivated.

Use of INAA for investigation of emission of elements in combustion of Polish lignite

International Nuclear Information System (INIS)

Janczyszyn, J.; Loska, L.; Pohorecki, W.; Wagner, M.

2002-01-01

Instrumental neutron activation analysis (INAA) has been applied for the determination of trace elements content in samples of Polish lignite and its ash. Pairs of results, for lignite and ash, and respective ash contents were used for calculation of the percentage of element remaining in ash after the lignite combustion. (author)

Relationships between soil and leaf mineral composition are element-specific, environment-dependent and geographically structured in the emerging model Arabidopsis halleri.

Science.gov (United States)

Stein, Ricardo J; Höreth, Stephan; de Melo, J Romário F; Syllwasschy, Lara; Lee, Gwonjin; Garbin, Mário L; Clemens, Stephan; Krämer, Ute

2017-02-01

Leaf mineral composition, the leaf ionome, reflects the complex interaction between a plant and its environment including local soil composition, an influential factor that can limit species distribution and plant productivity. Here we addressed within-species variation in plant-soil interactions and edaphic adaptation using Arabidopsis halleri, a well-suited model species as a facultative metallophyte and metal hyperaccumulator. We conducted multi-element analysis of 1972 paired leaf and soil samples from 165 European populations of A. halleri, at individual resolution to accommodate soil heterogeneity. Results were further confirmed under standardized conditions upon cultivation of 105 field-collected genotypes on an artificially metal-contaminated soil in growth chamber experiments. Soil-independent between- and within-population variation set apart leaf accumulation of zinc, cadmium and lead from all other nutrient and nonessential elements, concurring with differential hypothesized ecological roles in either biotic interaction or nutrition. For these metals, soil-leaf relationships were element-specific, differed between metalliferous and nonmetalliferous soils and were geographically structured both in the field and under standardized growth conditions, implicating complex scenarios of recent ecological adaptation. Our study provides an example and a reference for future related work and will serve as a basis for the molecular-genetic dissection and ecological analysis of the observed phenotypic variation. © 2016 The Authors. New Phytologist © 2016 New Phytologist Trust.

Safety-related investigations on power distribution in MOX fuel elements in LWR cores

International Nuclear Information System (INIS)

Kramer, E.; Langenbuch, S.

1991-01-01

For the concept of thermal recycling various fuel assembly designs have been developped during the last years. An overview is given describing the present status of MOX-fuel assembly design for PWR and BWR. The local power distribution within the MOX-fuel assembly and influences between neighbouring MOX- and Uranium fuel assemblies have been analyzed by own calculations. These investigations are limited to specific aspects of the spatial power distribution, which are related to the use of MOX-fuel assemblies within the reactor core of LWR. (orig.) [de

Investigation of the behaviour of some elements in heart of thymectomised rats

International Nuclear Information System (INIS)

Kinova, L.

1985-01-01

By means of instrumental neutron activation annalysis the elements K, Mn, Ca and Zn in heart of normal (intact) and thymectomised Wistar rats. Thymectomy was performed at the age of 3 months. Analysed were the hearths of intact animals at the age 3, 6, 9 and 12 months and the hearts of thymectomised animals at 15 days, 3, 6, and 9 months after thymectomy. Collection, cleaning, storage of the samples, as well as the irradiation, cooling and measuring mode and analytical isotopes used were described. It was established that the changes in the concentrations of the elements K, Mn, and Zn decrease in comparision with intact rats, and Ca concentration in heart increases

Chemical elemental distribution and soil DNA fingerprints provide the critical evidence in murder case investigation.

Directory of Open Access Journals (Sweden)

Giuseppe Concheri

Full Text Available BACKGROUND: The scientific contribution to the solution of crime cases, or throughout the consequent forensic trials, is a crucial aspect of the justice system. The possibility to extract meaningful information from trace amounts of samples, and to match and validate evidences with robust and unambiguous statistical tests, are the key points of such process. The present report is the authorized disclosure of an investigation, carried out by Attorney General appointment, on a murder case in northern Italy, which yielded the critical supporting evidence for the judicial trial. METHODOLOGY/PRINCIPAL FINDINGS: The proportional distribution of 54 chemical elements and the bacterial community DNA fingerprints were used as signature markers to prove the similarity of two soil samples. The first soil was collected on the crime scene, along a corn field, while the second was found in trace amounts on the carpet of a car impounded from the main suspect in a distant location. The matching similarity of the two soils was proven by crossing the results of two independent techniques: a elemental analysis via inductively coupled plasma mass spectrometry (ICP-MS and optical emission spectrometry (ICP-OES approaches, and b amplified ribosomal DNA restriction analysis by gel electrophoresis (ARDRA. CONCLUSIONS: Besides introducing the novel application of these methods to forensic disciplines, the highly accurate level of resolution observed, opens new possibilities also in the fields of soil typing and tracking, historical analyses, geochemical surveys and global land mapping.

A novel mammal-specific three partite enhancer element regulates node and notochord-specific Noto expression.

Directory of Open Access Journals (Sweden)

Leonie Alten

Full Text Available The vertebrate organizer and notochord have conserved, essential functions for embryonic development and patterning. The restricted expression of developmental regulators in these tissues is directed by specific cis-regulatory modules (CRMs whose sequence conservation varies considerably. Some CRMs have been conserved throughout vertebrates and likely represent ancestral regulatory networks, while others have diverged beyond recognition but still function over a wide evolutionary range. Here we identify and characterize a mammalian-specific CRM required for node and notochord specific (NNC expression of NOTO, a transcription factor essential for node morphogenesis, nodal cilia movement and establishment of laterality in mouse. A 523 bp enhancer region (NOCE upstream the Noto promoter was necessary and sufficient for NNC expression from the endogenous Noto locus. Three subregions in NOCE together mediated full activity in vivo. Binding sites for known transcription factors in NOCE were functional in vitro but dispensable for NOCE activity in vivo. A FOXA2 site in combination with a novel motif was necessary for NOCE activity in vivo. Strikingly, syntenic regions in non-mammalian vertebrates showed no recognizable sequence similarities. In contrast to its activity in mouse NOCE did not drive NNC expression in transgenic fish. NOCE represents a novel, mammal-specific CRM required for the highly restricted Noto expression in the node and nascent notochord and thus regulates normal node development and function.

A novel mammal-specific three partite enhancer element regulates node and notochord-specific Noto expression.

Science.gov (United States)

Alten, Leonie; Schuster-Gossler, Karin; Eichenlaub, Michael P; Wittbrodt, Beate; Wittbrodt, Joachim; Gossler, Achim

2012-01-01

The vertebrate organizer and notochord have conserved, essential functions for embryonic development and patterning. The restricted expression of developmental regulators in these tissues is directed by specific cis-regulatory modules (CRMs) whose sequence conservation varies considerably. Some CRMs have been conserved throughout vertebrates and likely represent ancestral regulatory networks, while others have diverged beyond recognition but still function over a wide evolutionary range. Here we identify and characterize a mammalian-specific CRM required for node and notochord specific (NNC) expression of NOTO, a transcription factor essential for node morphogenesis, nodal cilia movement and establishment of laterality in mouse. A 523 bp enhancer region (NOCE) upstream the Noto promoter was necessary and sufficient for NNC expression from the endogenous Noto locus. Three subregions in NOCE together mediated full activity in vivo. Binding sites for known transcription factors in NOCE were functional in vitro but dispensable for NOCE activity in vivo. A FOXA2 site in combination with a novel motif was necessary for NOCE activity in vivo. Strikingly, syntenic regions in non-mammalian vertebrates showed no recognizable sequence similarities. In contrast to its activity in mouse NOCE did not drive NNC expression in transgenic fish. NOCE represents a novel, mammal-specific CRM required for the highly restricted Noto expression in the node and nascent notochord and thus regulates normal node development and function.

A numerical investigation of the influence of radiation and moisture content on pyrolysis and ignition of a leaf-like fuel element

Science.gov (United States)

B.L. Yashwanth; B. Shotorban; S. Mahalingam; C.W. Lautenberger; David Weise

2016-01-01

The effects of thermal radiation and moisture content on the pyrolysis and gas phase ignition of a solid fuel element containing high moisture content were investigated using the coupled Gpyro3D/FDS models. The solid fuel has dimensions of a typical Arctostaphylos glandulosa leaf which is modeled as thin cellulose subjected to radiative heating on...

Investigation Procedure of Magnetic Performances of NdFeB Permanent Magnets

DEFF Research Database (Denmark)

Calin, Marius-Daniel; Helerea, Elena; Ritchie, Ewen

2011-01-01

The permanent magnet applications based on carbon steel magnets, hard ferrites and AlNiCo magnets classes are renewed with new classes of advanced magnetic materials based on rare earth elements, the Sm-Co and NdFeB types. Performance increase of the hard magnetic materials and their use in speci......The permanent magnet applications based on carbon steel magnets, hard ferrites and AlNiCo magnets classes are renewed with new classes of advanced magnetic materials based on rare earth elements, the Sm-Co and NdFeB types. Performance increase of the hard magnetic materials and their use...... in specific applications impose also great advances in the field of magnetic measurement. New researches need to be validated in order to investigate the NdFeB permanent magnets performances, including their stability under different thermal operational regimes. In this paper a specific investigation...... procedure of magnetic performances of NdFeB permanent magnets in correlation with the range of operating temperature is proposed based on modern hysteresisgraph method and impulse magnetization technique....

Identification of germline transcriptional regulatory elements in Aedes aegypti

Science.gov (United States)

Akbari, Omar S.; Papathanos, Philippos A.; Sandler, Jeremy E.; Kennedy, Katie; Hay, Bruce A.

2014-02-01

The mosquito Aedes aegypti is the principal vector for the yellow fever and dengue viruses, and is also responsible for recent outbreaks of the alphavirus chikungunya. Vector control strategies utilizing engineered gene drive systems are being developed as a means of replacing wild, pathogen transmitting mosquitoes with individuals refractory to disease transmission, or bringing about population suppression. Several of these systems, including Medea, UDMEL, and site-specific nucleases, which can be used to drive genes into populations or bring about population suppression, utilize transcriptional regulatory elements that drive germline-specific expression. Here we report the identification of multiple regulatory elements able to drive gene expression specifically in the female germline, or in the male and female germline, in the mosquito Aedes aegypti. These elements can also be used as tools with which to probe the roles of specific genes in germline function and in the early embryo, through overexpression or RNA interference.

Investigation on laser welding characteristics for appendage of bearing pads of nuclear fuel element

International Nuclear Information System (INIS)

Kim, S. S.; Kim, W. K.; Park, C. H.; Ko, J. H.; Lee, J. W.; Yang, M. S.

2001-01-01

In CANDU nuclear fuel manufacturing the brazing technology has been adopted conventionally to attach the bearing pads of nuclear fuel elements. However, in order to meet good performance of nuclear fuel and improved working efficiency, we started developing the laser welding technology for attachments of the bearing pads. Since the YAG laser can be suitable for small parts and transmit the beam through the optical fiber, the process is corresponding to mass-production with working shops. Making the most of this feature, we have developed the laser welding for appendage of the bearing pads of nuclear fuel elements, and has studied on the laser welding characterisitcs of appendages for nuclear fuel element

Investigation-Derived Waste Management Plan. Revision 2

International Nuclear Information System (INIS)

Molen, G.

1995-01-01

SRS has implemented a comprehensive environmental program to maintain compliance with environmental regulations and mitigate impacts to the environment. One element of the environmental program is the investigation of inactive waste units. Environmental Investigation-Derived Waste (IDW). IDW may include purge water , soil cuttings, drilling fluids, well pumping test and development water, decontamination solutions, contaminated equipment, and personal protection equipment (PPE). In cases where investigations confirm the presence of contamination and the IDW contains waste constituents in concentrations high enough to be of environmental or health concern, special management procedures are warranted. This IDW Management Plan describes specific SRS initiatives for IDW management. The goal is the development of a plan for prudent management of IDW from environmental investigations that is protective of human health and the environment

Pathological Buying Online as a Specific Form of Internet Addiction: A Model-Based Experimental Investigation.

Science.gov (United States)

Trotzke, Patrick; Starcke, Katrin; Müller, Astrid; Brand, Matthias

2015-01-01

The study aimed to investigate different factors of vulnerability for pathological buying in the online context and to determine whether online pathological buying has parallels to a specific Internet addiction. According to a model of specific Internet addiction by Brand and colleagues, potential vulnerability factors may consist of a predisposing excitability from shopping and as mediating variable, specific Internet use expectancies. Additionally, in line with models on addiction behavior, cue-induced craving should also constitute an important factor for online pathological buying. The theoretical model was tested in this study by investigating 240 female participants with a cue-reactivity paradigm, which was composed of online shopping pictures, to assess excitability from shopping. Craving (before and after the cue-reactivity paradigm) and online shopping expectancies were measured. The tendency for pathological buying and online pathological buying were screened with the Compulsive Buying Scale (CBS) and the Short Internet Addiction Test modified for shopping (s-IATshopping). The results demonstrated that the relationship between individual's excitability from shopping and online pathological buying tendency was partially mediated by specific Internet use expectancies for online shopping (model's R² = .742, p buying tendencies were correlated (r = .556, p buying (t(28) = 2.98, p buying and suggests potential parallels. The presence of craving in individuals with a propensity for online pathological buying emphasizes that this behavior merits potential consideration within the non-substance/behavioral addictions.

LIBS, LA-ICPMS and synchrotron hard x-ray micro-radiography and micro-tomography complementary study of elemental distributions in biominerals

International Nuclear Information System (INIS)

Kaiser, J.; Novotny, K.; Hola, M.; Kanicky, V.; Martinec, P.; Hahn, D.W.; Diwakar, P.K.; Mancini, L.; Tromba, G.; Sodini, N.

2009-01-01

Full text: Analysis of bio-minerals can provide information about the chronology, diet and palaeoenvironment of past populations. More specifically, e.g. line scans of uroliths cross-sections may be used to detect the accumulation history of the selected elements. This can be linked to the patients' exposure to environmental effects. Together with the main components, biogenous and toxic trace elements can be monitored. We report on utilization of two laser-ablation based analytical techniques for mapping elemental distribution in bio-minerals, coupled to hard x-ray microradiography and micro-CT measurements for visualization of the inner structure of the investigated samples. (author)

Programming the finite element method

CERN Document Server

Smith, I M; Margetts, L

2013-01-01

Many students, engineers, scientists and researchers have benefited from the practical, programming-oriented style of the previous editions of Programming the Finite Element Method, learning how to develop computer programs to solve specific engineering problems using the finite element method. This new fifth edition offers timely revisions that include programs and subroutine libraries fully updated to Fortran 2003, which are freely available online, and provides updated material on advances in parallel computing, thermal stress analysis, plasticity return algorithms, convection boundary c

Geometry reconstruction method for patient-specific finite element models for the assessment of tibia fracture risk in osteogenesis imperfecta.

Science.gov (United States)

Caouette, Christiane; Ikin, Nicole; Villemure, Isabelle; Arnoux, Pierre-Jean; Rauch, Frank; Aubin, Carl-Éric

2017-04-01

Lower limb deformation in children with osteogenesis imperfecta (OI) impairs ambulation and may lead to fracture. Corrective surgery is based on empirical assessment criteria. The objective was to develop a reconstruction method of the tibia for OI patients that could be used as input of a comprehensive finite element model to assess fracture risks. Data were obtained from three children with OI and tibia deformities. Four pQCT scans were registered to biplanar radiographs, and a template mesh was deformed to fit the bone outline. Cortical bone thickness was computed. Sensitivity of the model to missing slices of pQCT was assessed by calculating maximal von Mises stress for a vertical hopping load case. Sensitivity of the model to ±5 % of cortical thickness measurements was assessed by calculating loads at fracture. Difference between the mesh contour and bone outline on the radiographs was below 1 mm. Removal of one pQCT slice increased maximal von Mises stress by up to 10 %. Simulated ±5 % variation of cortical bone thickness leads to variations of up to 4.1 % on predicted fracture loads. Using clinically available tibia imaging from children with OI, the developed reconstruction method allowed the building of patient-specific finite element models.

Investigating size effects of complex nanostructures through Young-Laplace equation and finite element analysis

International Nuclear Information System (INIS)

Lu, Dingjie; Xie, Yi Min; Huang, Xiaodong; Zhou, Shiwei; Li, Qing

2015-01-01

Analytical studies on the size effects of a simply-shaped beam fixed at both ends have successfully explained the sudden changes of effective Young's modulus as its diameter decreases below 100 nm. Yet they are invalid for complex nanostructures ubiquitously existing in nature. In accordance with a generalized Young-Laplace equation, one of the representative size effects is transferred to non-uniformly distributed pressure against an external surface due to the imbalance of inward and outward loads. Because the magnitude of pressure depends on the principal curvatures, iterative steps have to be adopted to gradually stabilize the structure in finite element analysis. Computational results are in good agreement with both experiment data and theoretical prediction. Furthermore, the investigation on strengthened and softened Young's modulus for two complex nanostructures demonstrates that the proposed computational method provides a general and effective approach to analyze the size effects for nanostructures in arbitrary shape

Metrological system for y-ray spectrometry measurement of the specific activity and mass fraction of natural radioactive elements in soil and rock samples

International Nuclear Information System (INIS)

Khaikovich, I.M.; Fominykh, V.I.; Kirisyuk, E.M.; Belyachkov, Y.A.

1994-01-01

In the last few years a great deal of attention has been devoted to the study of the radiation conditions, which in some regions change markedly as a result of intense human activity. One reason for radioactive contamination of an area is dissemination during extraction and processing of radioactive ores or other minerals of natural radioactive elements with a high content of potassium, uranium (radium), and thorium. Estimation of the level of radioactive contamination is one of the main problems of ecological monitoring, and the quality of the measurements sometimes plays a deciding role in the fate of the object being investigated. This also pertains to, in particular, estimation of radioactive contamination of minerals employed for building homes and factories and other industrial structures. In order to draw unequivocal and well-founded conclusions from measurements of the content of natural radioactive elements in soil and rock samples, collected at the object being investigated, a great deal of attention must be devoted during the organization of the measurements to the metrological system

An Experimental and Finite Element Protocol to Investigate the Transport of Neutral and Charged Solutes across Articular Cartilage.

Science.gov (United States)

Arbabi, Vahid; Pouran, Behdad; Zadpoor, Amir A; Weinans, Harrie

2017-04-23

Osteoarthritis (OA) is a debilitating disease that is associated with degeneration of articular cartilage and subchondral bone. Degeneration of articular cartilage impairs its load-bearing function substantially as it experiences tremendous chemical degradation, i.e. proteoglycan loss and collagen fibril disruption. One promising way to investigate chemical damage mechanisms during OA is to expose the cartilage specimens to an external solute and monitor the diffusion of the molecules. The degree of cartilage damage (i.e. concentration and configuration of essential macromolecules) is associated with collisional energy loss of external solutes while moving across articular cartilage creates different diffusion characteristics compared to healthy cartilage. In this study, we introduce a protocol, which consists of several steps and is based on previously developed experimental micro-Computed Tomography (micro-CT) and finite element modeling. The transport of charged and uncharged iodinated molecules is first recorded using micro-CT, which is followed by applying biphasic-solute and multiphasic finite element models to obtain diffusion coefficients and fixed charge densities across cartilage zones.

Using Pupillometry to Investigate Sentence Comprehension in Children with and without Specific Language Impairment

Science.gov (United States)

Lum, Jarrad A. G.; Youssef, George J.; Clark, Gillian M.

2017-01-01

Purpose: In this study pupillometry was used to investigate the allocation of attentional resources associated with sentence comprehension in children with and without specific language impairment (SLI). Method: Eighteen children with SLI (age: M = 6.4 years) and 18 typically developing (TD) children (age: M = 6.3 years) participated in the study.…

An Investigation of Finite Element Analysis (FEA on Piezoelectric Compliance in Ultrasonic Vibration Assisted Milling (UVAM

Directory of Open Access Journals (Sweden)

Ibrahim Rasidi

2018-01-01

Full Text Available Finite element analysis for piezoelectric actuator has been developed in Ansys Software which are a program that can analyses and simulate the dynamic behaviour of piezoelectric. The Ultrasonic Vibration assisted Milling (UVAM experimental having a difficulty to investigate the effect of vibration mechanism where existence of error in material, mechanism and attachment of piezoelectric thus affect the amplitude and frequency of mechanical compliance during the machining of UVAM. This paper will investigate the modelling of piezoelectric compliance and follow the procedures of FEA to accurately predict the dynamic behaviour of compliance. The parameters for simulation of piezoelectric are voltage, electromechanical coupling and frequency. The compliance mechanism is model by using SolidWorks 2014 and imported to Ansys Mechanical APDL Software were the piezoelectric are embedded on the mechanism. Modal analysis and harmonic analysis has been used in order to obtain the mode shape and displacement. The displacement of the compliance mechanism will be compare between simulation and experimental. The dynamic behaviour was discussed in simulation to study the reliability of the compliance mechanism before it safely used in UVAM.

Biotic elements of NPP techno-ecosystem

International Nuclear Information System (INIS)

Protasov, A.A.; Silaeva, A.A.

2013-01-01

Specific features of biotic elements in the NPP techno-ecosystems were considered and compared with natural ecosystems. Relationships between biotic communities and environmental factors that are specific to the techno-ecosystems were discussed, and the problems of limitation of biological hindrances in operation of equipment, principles of hydrobiological and environmental monitoring were considered.

Elemental volatility of HT-9 fusion reactor alloy

International Nuclear Information System (INIS)

Henslee, S.P.; Neilson, R.M. Jr.

1985-01-01

The volatility of elemental constituents from HT-9, a ferritic steel, proposed for fusion reactor structures, was investigated. Tests were conducted in flowing air at temperatures from 800 to 1200 0 C for durations of 1 to 20 h. Elemental volatility was calculated in terms of the weight fraction of the element volatilized from the initial alloy; molybdenum, manganese, and nickel were the primary constituents volatilized. Comparisons with elemental volatilities observed for another candidate fusion reactor materials. Primary Candidate Alloy (PCA), an austenitic stainless steel, indicate significant differences between the volatilities of these steels that may impact fusion reactor safety analysis and alloy selection. Scanning electron microscopy and energy dispersive spectrometry were used to investigate the oxide layers formed on HT-9 and to measure elemental contents within these layers

Cohesive Modeling of Transverse Cracking in Laminates with a Single Layer of Elements per Ply

Science.gov (United States)

VanDerMeer, Frans P.; Davila, Carlos G.

2013-01-01

This study aims to bridge the gap between classical understanding of transverse cracking in cross-ply laminates and recent computational methods for the modeling of progressive laminate failure. Specifically, the study investigates under what conditions a finite element model with cohesive X-FEM cracks can reproduce the in situ effect for the ply strength. It is shown that it is possible to do so with a single element across the thickness of the ply, provided that the interface stiffness is properly selected. The optimal value for this interface stiffness is derived with an analytical shear lag model. It is also shown that, when the appropriate statistical variation of properties has been applied, models with a single element through the thickness of a ply can predict the density of transverse matrix cracks

Requirement-specific use of trace element biogas additives under consideration of the bioavailability; Bedarfsgerechter Einsatz von Spurenelement-Biogasadditiven unter Beruecksichtigung der Bioverfuegbarkeit

Energy Technology Data Exchange (ETDEWEB)

Feher, Adam; Fritz, Thomas; Loewen, Achim; Nelles, Michael [HAWK Hochschule fuer Angewandte Wissenschaft und Kunst Hildesheim/Holzminden/Goettingen, Goettingen (Germany). Fachgebiet Nachhaltige Energie- und Umwelttechnik (NEUTec)

2013-10-01

A highly efficient utilisation of substrates and operational stability at the same time is essential for the efficiency of a biogas plant. The research project SequEx of HAWK and /SF GmbH investigates the increase of efficiency of biogas plants by targeted use of trace elements taking into account bio-availability. Based on sequential extraction diagrams a method for the determination of bio-availability of macro- and micro-nutrients is developed. Within this context, different trace element compounds are analysed during the fermentation process on their share of bioavailable micro-nutrients as well as their effect on the biological activity of microorganisms. The actual knowledge gap between common practice of nutrients' supply and real impact shall be closed by the knowledge base enhancement of the bio-availability of nutrients. (orig.)

Trophic transfer of essential elements in the clownfish Amphiprion ocellaris in the context of ocean acidification.

Directory of Open Access Journals (Sweden)

Hugo Jacob

Full Text Available Little information exists on the effects of ocean acidification (OA on the digestive and post-digestive processes in marine fish. Here, we investigated OA impacts (Δ pH = 0.5 on the trophic transfer of select trace elements in the clownfish Amphiprion ocellaris using radiotracer techniques. Assimilation efficiencies of three essential elements (Co, Mn and Zn as well as their other short-term and long-term kinetic parameters in juvenile clownfish were not affected by this experimental pH change. In complement, their stomach pH during digestion were not affected by the variation in seawater pH. Such observations suggest that OA impacts do not affect element assimilation in these fish. This apparent pCO2 tolerance may imply that clownfish have the ability to self-regulate pH shifts in their digestive tract, or that they can metabolically accommodate such shifts. Such results are important to accurately assess future OA impacts on diverse marine biota, as such impacts are highly species specific, complex, and may be modulated by species-specific metabolic processes.

Table of specific activities of selected isotopes

International Nuclear Information System (INIS)

Shipley, G.

The bulk of this publication consists of a table of the half-lives, decay modes, and specific activities of isotopes selected for their particular interest to the Environmental Health and Safety Department, LBL. The specific activities were calculated with a PDP 9/15 computer. Also included in the report is a table of stable isotopes, the Th and U decay chains, a chart of the nuclides for elements 101 through 106, the heavy element region of the periodic table, and a specific activity monograph. 5 figures, 2 tables

Identification of a peroxisome proliferator responsive element (PPRE)-like cis-element in mouse plasminogen activator inhibitor-1 gene promoter

International Nuclear Information System (INIS)

Chen Jiegen; Li Xi; Huang Haiyan; Liu Honglei; Liu Deguo; Song Tanjing; Ma Chungu; Ma Duan; Song Houyan; Tang Qiqun

2006-01-01

PAI-1 is expressed and secreted by adipose tissue which may mediate the pathogenesis of obesity-associated cardiovascular complications. Evidence is presented in this report that PAI-1 is not expressed by preadipocyte, but significantly induced during 3T3-L1 adipocyte differentiation and the PAI-1 expression correlates with the induction of peroxisome proliferator-activated receptor γ (PPARγ). A peroxisome proliferator responsive element (PPRE)-like cis-element (-206TCCCCCATGCCCT-194) is identified in the mouse PAI-1 gene promoter by electrophoretic mobility shift assay (EMSA) combined with transient transfection experiments; the PPRE-like cis-element forms a specific DNA-protein complex only with adipocyte nuclear extracts, not with preadipocyte nuclear extracts; the DNA-protein complex can be totally competed away by non-labeled consensus PPRE, and can be supershifted with PPARγ antibody. Mutation of this PPRE-like cis-element can abolish the transactivation of mouse PAI-1 promoter mediated by PPARγ. Specific PPARγ ligand Pioglitazone can significantly induce the PAI-1 expression, and stimulate the secretion of PAI-1 into medium

Experimental Investigation on the Specific Heat of Carbonized Phenolic Resin-Based Ablative Materials

Science.gov (United States)

Zhao, Te; Ye, Hong; Zhang, Lisong; Cai, Qilin

2017-10-01

As typical phenolic resin-based ablative materials, the high silica/phenolic and carbon/phenolic composites are widely used in aerospace field. The specific heat of the carbonized ablators after ablation is an important thermophysical parameter in the process of heat transfer, but it is rarely reported. In this investigation, the carbonized samples of the high silica/phenolic and carbon/phenolic were obtained through carbonization experiments, and the specific heat of the carbonized samples was determined by a 3D DSC from 150 °C to 970 °C. Structural and compositional characterizations were performed to determine the mass fractions of the fiber and the carbonized product of phenolic which are the two constituents of the carbonized samples, while the specific heat of each constituent was also measured by 3D DSC. The masses of the carbonized samples were reduced when heated to a high temperature in the specific heat measurements, due to the thermal degradation of the carbonized product of phenolic resin in the carbonized samples. The raw experimental specific heat of the two carbonized samples and the carbonized product of phenolic resin was modified according to the quality changes of the carbonized samples presented by TGA results. Based on the mass fraction and the specific heat of each constituent, a weighted average method was adopted to obtain the calculated results of the carbonized samples. Due to the unconsolidated property of the fiber samples which impacts the reliability of the DSC measurement, there is a certain deviation between the experimental and calculated results of the carbonized samples. Considering the similarity of composition and structure, the data of quartz glass and graphite were used to substitute the specific heat of the high silica fiber and carbon fiber, respectively, resulting in better agreements with the experimental ones. Furthermore, the accurate specific heat of the high silica fiber and carbon fiber bundles was obtained by

Verification of Orthogrid Finite Element Modeling Techniques

Science.gov (United States)

Steeve, B. E.

1996-01-01

The stress analysis of orthogrid structures, specifically with I-beam sections, is regularly performed using finite elements. Various modeling techniques are often used to simplify the modeling process but still adequately capture the actual hardware behavior. The accuracy of such 'Oshort cutso' is sometimes in question. This report compares three modeling techniques to actual test results from a loaded orthogrid panel. The finite element models include a beam, shell, and mixed beam and shell element model. Results show that the shell element model performs the best, but that the simpler beam and beam and shell element models provide reasonable to conservative results for a stress analysis. When deflection and stiffness is critical, it is important to capture the effect of the orthogrid nodes in the model.

Investigation of some Macro and Micro Elements in Soil and Sugarcane Plant in Elguneid Scheme

International Nuclear Information System (INIS)

Hassona, R.K.

1996-09-01

The contents of some macro nutrients(N,Mg,P,K and Ca), micro nutrients(Mn,Fe,Cu,Zn and Mo) and other elements in sugarcane plant and soil samples in Elguneid scheme were evaluated in this study.During this study soil and plant samples were taken from different depths and different sites.Plant samples were collected from the same sites at 6 and 10 months age.The objectives of this work were to determine the nutrient contents of soil and sugarcane plant, to relate the nutrient contents of soil with that of plant and to compare the average elemental content of soil and plant with the available literature.To achieve the above mentioned goals,atomic absorption spectrometry(AAS), X-ray fluorescence,flame photometry,kjeldahl method and colorimetry were used for the elemental analysis of soil and plant samples. It was found that the elemental concentration decreases with soil depth increase.There were no seasonal variations in the elemental in soil and plant samples.The data obtained in this work for soil and plant samples were comparable to those reported in litreature in other areas.Using the elemental concentration ratios in soil and plant samples referred to the concentration of iron which is an indicator of soil as a source. The enrichment factor for some nutrients was calculated that N, P, and K have some sources other than soil, such as fertilizers and pesticides. (Author)

Investigation of some Macro and Micro Elements in Soil and Sugarcane Plant in Elguneid Scheme

Energy Technology Data Exchange (ETDEWEB)

Hassona, R K [Sudan Atomic Energy Commission, Khartoum (Sudan)

1996-09-01

The contents of some macro nutrients(N,Mg,P,K and Ca), micro nutrients(Mn,Fe,Cu,Zn and Mo) and other elements in sugarcane plant and soil samples in Elguneid scheme were evaluated in this study.During this study soil and plant samples were taken from different depths and different sites.Plant samples were collected from the same sites at 6 and 10 months age.The objectives of this work were to determine the nutrient contents of soil and sugarcane plant, to relate the nutrient contents of soil with that of plant and to compare the average elemental content of soil and plant with the available literature.To achieve the above mentioned goals,atomic absorption spectrometry(AAS), X-ray fluorescence,flame photometry,kjeldahl method and colorimetry were used for the elemental analysis of soil and plant samples. It was found that the elemental concentration decreases with soil depth increase.There were no seasonal variations in the elemental in soil and plant samples.The data obtained in this work for soil and plant samples were comparable to those reported in litreature in other areas.Using the elemental concentration ratios in soil and plant samples referred to the concentration of iron which is an indicator of soil as a source. The enrichment factor for some nutrients was calculated that N, P, and K have some sources other than soil, such as fertilizers and pesticides. (Author). 85 refs., 27 tabs., 20 figs.

Experimental Investigation and Finite Element Analysis on Fatigue Behavior of Aluminum Alloy 7050 Single-Lap Joints

Science.gov (United States)

Zhou, Bing; Cui, Hao; Liu, Haibo; Li, Yang; Liu, Gaofeng; Li, Shujun; Zhang, Shangzhou

2018-03-01

The fatigue behavior of single-lap four-riveted aluminum alloy 7050 joints was investigated by using high-frequency fatigue test and scanning electron microscope (SEM). Stress distributions obtained by finite element (FE) analysis help explain the fatigue performance. The fatigue test results showed that the fatigue lives of the joints depend on cold expansion and applied cyclic loads. FE analysis and fractography indicated that the improved fatigue lives can be attributed to the reduction in maximum stress and evolution of fatigue damage at the critical location. The beneficial effects of strengthening techniques result in tearing ridges or lamellar structure on fracture surface, decrease in fatigue striations spacing, delay of fatigue crack initiation, crack deflection in fatigue crack propagation and plasticity-induced crack closure.

Toxic element profiles in selected medicinal plants growing on serpentines in Bulgaria.

Science.gov (United States)

Pavlova, Dolja; Karadjova, Irina

2013-12-01

Populations of medicinal plants growing on serpentines and their respective soils were analyzed for Fe, Ni, Mn, Cr, Co, Cd, Cu, Zn, and Pb using inductively coupled plasma atomic emission spectrometry. Aqua regia extraction and 0.43 M acetic acid extraction were used for the quantification of pseudototal and bioavailable fractions, respectively, of elements in soil and nitric acid digestion for determination of total element content in plants. Screening was performed to (1) document levels of toxic metals in herbs extensively used in preparation of products and standardized extracts, (2) compare accumulation abilities of ferns and seed plants, and (3) estimate correlations between metal content in plants and their soils. The toxic element content of plants varied from site to site on a large scale. The concentrations of Fe and Ni were elevated while those of Cu, Zn, and Pb were close to average values usually found in plants. The highest concentrations for almost all elements were measured in both Teucrium species. Specific differences in metal accumulation between ferns and seed plants were not recorded. The investigated species are not hyperaccumulators but can accumulate toxic elements, in some cases exceeding permissible levels proposed by the World Health Organization and European Pharmacopoeia. The harvesting of medicinal plants from serpentines could be hazardous to humans.

Trace element mapping of two Pyrenean chert deposits (SW Europe) by PIXE

Energy Technology Data Exchange (ETDEWEB)

Sánchez de la Torre, Marta, E-mail: marta.sanchez-de-la-torre@u-bordeaux-montaigne.fr [IRAMAT-CRP2A (UMR 5060), CNRS/Université Bordeaux Montaigne, Maison de l’Archéologie, Esplanade des Antilles, 33607 Pessac Cedex (France); SERP-Universitat de Barcelona, Montalegre St 6-8, 08001 Barcelona (Spain); Angyal, Anikó; Kertész, Zsófia [MTA Atomki, Institute for Nuclear Research, Hungarian Academy of Sciences, H-4026 Debrecen (Hungary); Dubernet, Stéphan; Le Bourdonnec, François-Xavier [IRAMAT-CRP2A (UMR 5060), CNRS/Université Bordeaux Montaigne, Maison de l’Archéologie, Esplanade des Antilles, 33607 Pessac Cedex (France); Csedreki, László; Furu, Enikő; Papp, Enikő; Szoboszlai, Zoltán; Szikszai, Zita [MTA Atomki, Institute for Nuclear Research, Hungarian Academy of Sciences, H-4026 Debrecen (Hungary)

2017-06-01

The geochemical character of two chert formations from the Pyrenean mountain range (SW Europe) was established by PIXE analyses. While it was not possible to distinguish the formations through reference to major and minor elements, some variations were revealed at the trace elemental level. In order to determine if these elements are associated with the Si matrix or to the contents of a specific inclusion, elemental maps were acquired and the elemental composition of the identified inclusions were also determined. As a result, Sr, Ni and Zn are better represented in Montgaillard samples while Y, Hf, W and Zr are typical of Montsaunès cherts. Thanks to elemental maps it has been possible to determine that most of these characteristic elements are usually related to a specific inclusion content.

Investigating Human-Induced Changes of Elemental Cycles in the Great Lakes

Science.gov (United States)

Baskaran, Mark; Bratton, John

2013-07-01

Food webs and associated elemental cycles in the Laurentian Great Lakes have been considerably altered over the past 30 years due to factors such as phosphorus abatement, introduction of zebra and quagga mussels, and climate change. These perturbations provide a unique opportunity to document how this natural system has responded and possibly to predict future changes in biogeochemical cycling.

Carnivore-specific SINEs (Can-SINEs): distribution, evolution, and genomic impact.

Science.gov (United States)

Walters-Conte, Kathryn B; Johnson, Diana L E; Allard, Marc W; Pecon-Slattery, Jill

2011-01-01

Short interspersed nuclear elements (SINEs) are a type of class 1 transposable element (retrotransposon) with features that allow investigators to resolve evolutionary relationships between populations and species while providing insight into genome composition and function. Characterization of a Carnivora-specific SINE family, Can-SINEs, has, has aided comparative genomic studies by providing rare genomic changes, and neutral sequence variants often needed to resolve difficult evolutionary questions. In addition, Can-SINEs constitute a significant source of functional diversity with Carnivora. Publication of the whole-genome sequence of domestic dog, domestic cat, and giant panda serves as a valuable resource in comparative genomic inferences gleaned from Can-SINEs. In anticipation of forthcoming studies bolstered by new genomic data, this review describes the discovery and characterization of Can-SINE motifs as well as describes composition, distribution, and effect on genome function. As the contribution of noncoding sequences to genomic diversity becomes more apparent, SINEs and other transposable elements will play an increasingly large role in mammalian comparative genomics.

Element patterns in albatrosses and petrels: Influence of trophic position, foraging range, and prey type

International Nuclear Information System (INIS)

Anderson, O.R.J.; Phillips, R.A.; Shore, R.F.; McGill, R.A.R.; McDonald, R.A.; Bearhop, S.

2010-01-01

We investigated the concentrations of 22 essential and non-essential elements among a community of Procellariiformes (and their prey) to identify the extent to which trophic position and foraging range governed element accumulation. Stable isotope analysis (SIA) was used to characterise trophic (δ 15 N) and spatial patterns (δ 13 C) among species. Few consistent patterns were observed in element distributions among species and diet appeared to be highly influential in some instances. Arsenic levels in seabird red blood cells correlated with δ 15 N and δ 13 C, demonstrating the importance of trophic position and foraging range for arsenic distribution. Arsenic concentrations in prey varied significantly across taxa, and in the strength of association with δ 15 N values (trophic level). In most instances, element patterns in Procellariiformes showed the clearest separation among species, indicating that a combination of prey selection and other complex species-specific characteristics (e.g. moult patterns) were generally more important determining factors than trophic level per se. - Trophic position, foraging range, and prey type were found to influence element compositions and concentrations in Procellariiformes from South Georgia.

Chemistry gains a new element: Z=106

International Nuclear Information System (INIS)

Gaeggeler, H.W.; Eichler, B.; Tuerler, A.

1997-01-01

Even though 112 chemical elements are presently known, for elements with atomic numbers above 105 only nuclear decay properties have been investigated so far. Such data allow to proof the existence of a given nuclide, but they do not yield any information with respect to the position of a chemical element in the Periodic Table. We have performed ever first chemical investigations of element 106. According to the Periodic Table element 106 should be a member of group 6, having similar chemical properties as W, Mo and Cr. Two different techniques were applied to separate and identify element 106: a liquid chromatography system (ARCA = Automated Rapid Chemistry Apparatus) and a continuous isothermal chromatography device (OLGA = On-Line Gaschemistry Apparatus). With ARCA about 5'000 separations on small cation exchange columns (Aminex A6) with a 0.1 M HNO 3 /5.10 -4 M Hf solution were performed and with OLGA the gas adsorption behaviour of oxychlorides on quartz columns using Cl 2 /SOCl 2 /O 2 as reactive gas were studied. On the basis of only ten detected atoms, it was possible to proof that element 106 forms complexes which are eluted at positions similar to those of Mo and W. In addition, in the gas phase element 106 forms oxychlorides of lower volatility compared to those of Mo and W. (author) 1 ref

Ultraviolet B (UVB) induction of the c-fos promoter is mediated by phospho-cAMP response element binding protein (CREB) binding to CRE and c-fos activator protein 1 site (FAP1) cis elements.

Science.gov (United States)

Gonzales, Melissa; Bowden, G Tim

2002-06-26

The ultraviolet B (UVB) portion (280-320 nm) of the ultraviolet spectrum has been shown to contribute to the development of non-melanoma skin cancer in humans. Research in the human keratinocyte cell line, HaCaT, revealed that UVB irradiation caused the upregulation of the transcription factor activator protein-1 (AP-1). The AP-1 complex formed in UVB-irradiated HaCaT cells is specifically composed of c-fos and Jun D. c-Fos expression was induced in a manner that correlated with the UVB-induced activation of AP-1. To investigate how c-fos expression is regulated by UVB irradiation, the role of each of four cis elements within the c-fos promoter was evaluated. Clustered point mutations at the sis inducible element (SIE), serum response element (SRE), c-fos AP-1 site (FAP1), or cyclic AMP response elements (CRE) significantly inhibited UVB induction of the c-fos promoter. This indicated that all four cis elements are required for maximum promoter activity. The CRE and FAP1 elements were the two most active cis elements that mediate the UVB transactivation of c-fos. Homodimers of phosphorylated cAMP response element binding protein (CREB) were induced by UVB irradiation to bind to each of these elements. Therefore, CREB may function as an important regulatory protein in the UVB-induced expression of c-fos.

Divergent evolutionary rates in vertebrate and mammalian specific conserved non-coding elements (CNEs) in echolocating mammals.

Science.gov (United States)

Davies, Kalina T J; Tsagkogeorga, Georgia; Rossiter, Stephen J

2014-12-19

The majority of DNA contained within vertebrate genomes is non-coding, with a certain proportion of this thought to play regulatory roles during development. Conserved Non-coding Elements (CNEs) are an abundant group of putative regulatory sequences that are highly conserved across divergent groups and thus assumed to be under strong selective constraint. Many CNEs may contain regulatory factor binding sites, and their frequent spatial association with key developmental genes - such as those regulating sensory system development - suggests crucial roles in regulating gene expression and cellular patterning. Yet surprisingly little is known about the molecular evolution of CNEs across diverse mammalian taxa or their role in specific phenotypic adaptations. We examined 3,110 vertebrate-specific and ~82,000 mammalian-specific CNEs across 19 and 9 mammalian orders respectively, and tested for changes in the rate of evolution of CNEs located in the proximity of genes underlying the development or functioning of auditory systems. As we focused on CNEs putatively associated with genes underlying the development/functioning of auditory systems, we incorporated echolocating taxa in our dataset because of their highly specialised and derived auditory systems. Phylogenetic reconstructions of concatenated CNEs broadly recovered accepted mammal relationships despite high levels of sequence conservation. We found that CNE substitution rates were highest in rodents and lowest in primates, consistent with previous findings. Comparisons of CNE substitution rates from several genomic regions containing genes linked to auditory system development and hearing revealed differences between echolocating and non-echolocating taxa. Wider taxonomic sampling of four CNEs associated with the homeobox genes Hmx2 and Hmx3 - which are required for inner ear development - revealed family-wise variation across diverse bat species. Specifically within one family of echolocating bats that utilise

Investigation of trace elements in Guangxi ancient pottery by INAA

International Nuclear Information System (INIS)

Peng Zicheng; Sun Weidong; Huang Yunlan

1997-01-01

Guangxi Zhuang Nationality Autonomous Region is an original place for manufacture of ancient pottery in China since Zenpiyan site, dated 9240-10370 years ago, was excavated. Contents of trace elements La, Ce, Nd, Sm, Eu, Tb, Yb, Lu, U, Th, Sc, Ta, Ba, Cs, Rb, Sr and Zr in 44 pottery shards from Guangxi sites, dated from 1450 B.C. to 200 A.D., were determined by INAA and XRF. The provenances of the 44 samples are postulated by the analyses of geochemical parameters

A comparison of human elements and nonhuman elements in private health care settings: customers' perceptions and expectations.

Science.gov (United States)

Mohd Suki, Norazah; Chwee Lian, Jennifer Chiam; Suki, Norbayah Mohd

2009-01-01

In today's highly competitive health care environment, many private health care settings are now looking into customer service indicators to learn customers' perceptions and determine whether they are meeting customers' expectations in order to ensure that their customers are satisfied with the services. This research paper aims to investigate whether the human elements were more important than the nonhuman elements in private health care settings. We used the internationally renowned SERVQUAL five-dimension model plus three additional dimensions-courtesy, communication, and understanding of customers of the human element-when evaluating health care services. A total of 191 respondents from three private health care settings in the Klang Valley region of Malaysia were investigated. Descriptive statistics were calculated by the Statistical Package for Social Sciences (SPSS) computer program, version 15. Interestingly, the results suggested that customers nowadays have very high expectations especially when it comes to the treatment they are receiving. Overall, the research indicated that the human elements were more important than the nonhuman element in private health care settings. Hospital management should look further to improve on areas that have been highlighted. Implications for management practice and directions for future research are discussed.

Finite Element Based Design and Optimization for Piezoelectric Accelerometers

DEFF Research Database (Denmark)

Liu, Bin; Kriegbaum, B.; Yao, Q.

1998-01-01

A systematic Finite Element design and optimisation procedure is implemented for the development of piezoelectric accelerometers. Most of the specifications of accelerometers can be obtained using the Finite Element simulations. The deviations between the simulated and calibrated sensitivities...

The extraction of some trivalent elements with Aliquat-336

Energy Technology Data Exchange (ETDEWEB)

FLandgren, A.; Liljenzin, J.O.; Skalberg, M. [Chalmers Univ. of Technology, Goeteborg (Sweden)

1995-10-01

The extraction behaviour of some trivalent elements in the Aliquate-336-1,3-diisopropyl genzene-nitric acid system has been investigated. For most of the elements a maximum in the distribution ratio occur at about 2 molar nitric acid. At 0.20 molar Aliquate-336 lanthanum attained the highest distribution ratio, about 0.05, of all investigated elements. It was found that nitric acid to a large extent influences the distribution ratio of trivalent elements since it competes with metal nitrate complexes for the extractant molecules. A first approach to a model describing the extraction system is derived.

Investigating the Lymphatic System by Dual-Color Elemental Mass Spectrometry Imaging

Directory of Open Access Journals (Sweden)

Ann-Christin Niehoff

2017-01-01

Full Text Available Secondary lymphedema accompanied with strong restrictions in quality of life is still major side effects in cancer therapy. Therefore, dedicated diagnostic tools and further investigation of the lymphatic system are crucial to improve lymphedema therapy. In this pilot study, a method for quantitative analysis of the lymphatic system in a rat model by laser ablation (LA with inductively coupled plasma mass spectrometry imaging (ICP-MSI is presented. As a possible lymph marker, thulium(III(1R,4R,7R,10R-α,α′,α′′,α′′′-tetramethyl-1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraacetate (Tm-DOTMA is introduced and compared to the clinically used magnetic resonance imaging contrast agent gadolinium(III2,2′,2′′-(10-((2R,3S-1,3,4-trihydroxybutan-2-yl-1,4,7,10-tetraazacyclododecane-1,4,7-triyltriacetate (Gd-DO3A-butrol. Gadobutrol functioned as standard contrast media in MRI lymphangiography to detect lymphatic flow qualitatively. Thus, Tm-DOTMA was investigated as lymphatic marker to detect lymphatic flow quantitatively. Both contrast agents were successfully used to visualize the lymphatic flow in successive lymph nodes in LA-ICP-MS due to lower limits of detection compared to MRI. Furthermore, the distribution of contrast agents by multicolored imaging showed accumulation in specific areas (sectors of the lymph nodes after application of contrast agents in different areas.

Atom-scale depth localization of biologically important chemical elements in molecular layers.

Science.gov (United States)

Schneck, Emanuel; Scoppola, Ernesto; Drnec, Jakub; Mocuta, Cristian; Felici, Roberto; Novikov, Dmitri; Fragneto, Giovanna; Daillant, Jean

2016-08-23

In nature, biomolecules are often organized as functional thin layers in interfacial architectures, the most prominent examples being biological membranes. Biomolecular layers play also important roles in context with biotechnological surfaces, for instance, when they are the result of adsorption processes. For the understanding of many biological or biotechnologically relevant phenomena, detailed structural insight into the involved biomolecular layers is required. Here, we use standing-wave X-ray fluorescence (SWXF) to localize chemical elements in solid-supported lipid and protein layers with near-Ångstrom precision. The technique complements traditional specular reflectometry experiments that merely yield the layers' global density profiles. While earlier work mostly focused on relatively heavy elements, typically metal ions, we show that it is also possible to determine the position of the comparatively light elements S and P, which are found in the most abundant classes of biomolecules and are therefore particularly important. With that, we overcome the need of artificial heavy atom labels, the main obstacle to a broader application of high-resolution SWXF in the fields of biology and soft matter. This work may thus constitute the basis for the label-free, element-specific structural investigation of complex biomolecular layers and biological surfaces.

Storage and pre-neutron-activation-analysis treatment for trace-element analysis in urine

International Nuclear Information System (INIS)

Blotcky, A.J.; Rack, E.P.

1985-01-01

The problems regarding storage and pre-neutron-activation-analysis treatment for the elements aluminum, calcium, vanadium, selenium, copper, iodine, zinc, manganese, and magnesium in a urine matrix are reviewed. The type of collection and storage procedure and pre-neutron activation analysis treatment of urine depend on the specific trace element; that is, its inherent physical and chemical properties. Specifically polyethylene in teflon containers are the most suitable for general determinations. Whether any preservative is added would depend upon the stability of the trace element and its tendency for surface adsorption. Preferably, preservatives should contain no radioactivatable elements for maximum efficacy. Freeze drying or packing urine shipments under dry ice needs to be explored on an individual basis. Each pre- or post-neutron activation analysis treatment is specific and optimized for the trace element analyzed

A discrete element based simulation framework to investigate particulate spray deposition processes

KAUST Repository

Mukherjee, Debanjan; Zohdi, Tarek I.

2015-01-01

© 2015 Elsevier Inc. This work presents a computer simulation framework based on discrete element method to analyze manufacturing processes that comprise a loosely flowing stream of particles in a carrier fluid being deposited on a target surface

Preparation of spherical fuel elements for HTR-PM in INET

International Nuclear Information System (INIS)

Xiangwen, Zhou; Zhenming, Lu; Jie, Zhang; Bing, Liu; Yanwen, Zou; Chunhe, Tang; Yaping, Tang

2013-01-01

Highlights: • Modifications and optimizations in the manufacture of spherical fuel elements (SFE) for HTR-PM are presented. • A newly developed overcoater exhibits good stability and high efficiency in the preparation of overcoated particles. • The optimized carbonization process reduces the process time from 70 h in the period of HTR-10 to 20 h. • Properties of the prepared SFE and matrix graphite balls meet the design specifications for HTR-PM. • In particular the mean free uranium fraction of 5 consecutive batches is only 8.7 × 10 −6 . -- Abstract: The spherical fuel elements were successfully manufactured in the period of HTR-10. In order to satisfy the mass production of fuel elements for HTR-PM, several measures have been taken in modifying and optimizing the manufacture process of fuel elements. The newly developed overcoater system and its corresponding parameters exhibited good stability and high efficiency in the preparation of overcoated particles. The optimized carbonization process could reduce the carbonization time from more than 70 h to 20 h and improve the manufacturing efficiency. Properties of the manufactured spherical fuel elements and matrix graphite balls met the design specifications for HTR-PM. The mean free uranium fraction of 5 consecutive batches was 8.7 × 10 −6 . The optimized fuel elements manufacturing process could meet the requirements of design specifications of spherical fuel elements for HTR-PM

SXT/R391 ICE elements encode a novel ‘trap-door’ strategy for mobile element escape

Directory of Open Access Journals (Sweden)

Michael P Ryan

2016-05-01

Full Text Available Integrative Conjugative Elements (ICEs are a class of bacterial mobile elements that have the ability to mediate their own integration, excision and transfer from one host genome to another by a mechanism of site-specific recombination, self-circularisation and conjugative transfer. Members of the SXT/R391 ICE family of enterobacterial mobile genetic elements display an unusual UV-inducible sensitisation function which results in stress induced killing of bacterial cells harbouring the ICE. This sensitisation has been shown to be associated with a stress induced overexpression of a mobile element encoded conjugative transfer gene, orf43, a traV homolog. This results in cell lysis and release of a circular form of the ICE. Induction of this novel system may allow transfer of an ICE, enhancing its survival potential under conditions not conducive to conjugative transfer.

A Centerline Based Model Morphing Algorithm for Patient-Specific Finite Element Modelling of the Left Ventricle.

Science.gov (United States)

Behdadfar, S; Navarro, L; Sundnes, J; Maleckar, M; Ross, S; Odland, H H; Avril, S

2017-09-20

Hexahedral automatic model generation is a recurrent problem in computer vision and computational biomechanics. It may even become a challenging problem when one wants to develop a patient-specific finite-element (FE) model of the left ventricle (LV), particularly when only low resolution images are available. In the present study, a fast and efficient algorithm is presented and tested to address such a situation. A template FE hexahedral model was created for a LV geometry using a General Electric (GE) ultrasound (US) system. A system of centerline was considered for this LV mesh. Then, the nodes located over the endocardial and epicardial surfaces are respectively projected from this centerline onto the actual endocardial and epicardial surfaces reconstructed from a patient's US data. Finally, the position of the internal nodes is derived by finding the deformations with minimal elastic energy. This approach was applied to eight patients suffering from congestive heart disease. A FE analysis was performed to derive the stress induced in the LV tissue by diastolic blood pressure on each of them. Our model morphing algorithm was applied successfully and the obtained meshes showed only marginal mismatches when compared to the corresponding US geometries. The diastolic FE analyses were successfully performed in seven patients to derive the distribution of principal stresses. The original model morphing algorithm is fast and robust with low computational cost. This low cost model morphing algorithm may be highly beneficial for future patient-specific reduced-order modelling of the LV with potential application to other crucial organs.

Study of mobilization and speciation of trace elements in coal pyrolysis

International Nuclear Information System (INIS)

Ting, B.T.G.

1979-01-01

Various types of coal contain high levels of a number of trace elements. Little is known of the fates of these trace elements during the conversion of coal to liquid and gaseous products. Studies were undertaken of mobilization and speciation of trace elements in coal pyrolysis, one of the major coal conversion processes. The bituminous coal was pyrolyzed to produce liquid and gaseous products. The pyrolysis products were collected in traps in an inert gas stream. In addition mildly hydrogenated coal was prepared by mixing with tetralin, a hydrogen donor solvent, at boiling temperature. In order to characterize each element specifically during pyrolysis, base samples of coal and mildly hydrogenated coal (H-coal) were spiked with heavy metal sulfides, trace metals bound to partially oxidized coal (coal humates), and halide salts prior to carrying out pyrolysis. Eight elements were investigated in this research. They are As, Br, Cl, Co, Cr, Mn, Se, and V. Pre-spiked hydrogenated coal, i.e., pulverized coal spiked with halide salts and heavy metal sulfides then hydrogenated with tetralin, was prepared and studied for the fates of these elements during pyrolysis. Chlorinated and brominated coals were also prepared to compare the volatility differences between organically and inorganically bound halogens during the pyrolysis reaction. These products and the coal char residues were analyzed for the spiked elements mainly by neutron activation analysis for the spiked elements to determine their degree of volatility. Volatility and recovery (mass balance) will be discussed for those elements that appeared highly volatile during pyrolysis. In order to understand the halogenated compounds in the pyrolysis products, gas chromatograms were taken to the collected pyrolysis products of coal, hydrogenated coal, NaCl spiked coal, NaBr spiked coal, chlorinated coal, and brominated coal

Investigate the effect of anisotropic order parameter on the specific heat of anisotropic two-band superconductors

International Nuclear Information System (INIS)

Udomsamuthirun, P.; Peamsuwan, R.; Kumvongsa, C.

2009-01-01

The effect of anisotropic order parameter on the specific heat of anisotropic two-band superconductors in BCS weak-coupling limit is investigated. An analytical specific heat jump and the numerical specific heat are shown by using anisotropic order parameters, and the electron-phonon interaction and non-electron-phonon interaction. The two models of anisotropic order parameters are used for numerical calculation that we find little effect on the numerical results. The specific heat jump of MgB 2 , Lu 2 Fe 3 Si 5 and Nb 3 Sn superconductors can fit well with both of them. By comparing the experimental data with overall range of temperature, the best fit is Nb 3 Sn, MgB 2 , and Lu 2 Fe 3 Si 5 superconductors.

On the reliability of finite element solutions

International Nuclear Information System (INIS)

Prasad, K.S.R.K.

1975-01-01

The extent of reliability of the finite element method for analysis of nuclear reactor structures, and that of reactor vessels in particular and the need for the engineer to guard against the pitfalls that may arise out of both physical and mathematical models have been high-lighted. A systematic way of checking the model to obtain reasonably accurate solutions is presented. Quite often sophisticated elements are suggested for specific design and stress concentration problems. The desirability or otherwise of these elements, their scope and utility vis-a-vis the use of large stack of conventional elements are discussed from the view point of stress analysts. The methods of obtaining a check on the reliability of the finite element solutions either through modelling changes or an extrapolation technique are discussed. (author)

Identification of choriogenin cis-regulatory elements and production of estrogen-inducible, liver-specific transgenic Medaka.

Science.gov (United States)

Ueno, Tetsuro; Yasumasu, Shigeki; Hayashi, Shinji; Iuchi, Ichiro

2004-07-01

Choriogenins (chg-H, chg-L) are precursor proteins of egg envelope of medaka and synthesized in the spawning female liver in response to estrogen. We linked a gene construct chg-L1.5 kb/GFP (a 1.5 kb 5'-upstream region of the chg-L gene fused with a green fluorescence protein (GFP) gene) to another construct emgb/RFP (a cis-regulatory region of embryonic globin gene fused with an RFP gene), injected the double fusion gene construct into 1- or 2-cell-stage embryos, and selected embryos expressing the RFP in erythroid cells. From the embryos, we established two lines of chg-L1.5 kb/GFP-emgb/RFP-transgenic medaka. The 3-month-old spawning females and estradiol-17beta (E2)-exposed males displayed the liver-specific GFP expression. The E2-dependent GFP expression was detected in the differentiating liver of the stage 37-38 embryos. In addition, RT-PCR and whole-mount in situ hybridization showed that the E2-dependent chg expression was found in the liver of the stage 34 embryos of wild medaka, suggesting that such E2-dependency is achieved shortly after differentiation of the liver. Analysis using serial deletion mutants fused with GFP showed that the region -426 to -284 of the chg-L gene or the region -364 to -265 of the chg-H gene had the ability to promote the E2-dependent liver-specific GFP expression of its downstream gene. Further analyses suggested that an estrogen response element (ERE) at -309, an ERE half-site at -330 and a binding site for C/EBP at -363 of the chg-L gene played important roles in its downstream chg-L gene expression. In addition, this transgenic medaka may be useful as one of the test animals for detecting environmental estrogenic steroids.

Autokinase activity of alpha-crystallin inhibits its specific interaction with the DOTIS element in the murine gamma D/E/F-crystallin promoter in vitro.

Science.gov (United States)

Pietrowski, D; Graw, J

1997-10-01

In a previous report we demonstrated the in vitro interaction of alpha-crystallin with an element downstream of the transcriptional initiation site (DOTIS) of the murine gamma E-crystallin promoter (Pietrowski et al., 1994, Gene 144, 171-178). The aim of the present study was to investigate the influence of phosphorylation on this particular interaction. We could demonstrate that the autophosphorylation of alpha-crystallin leads to a complete loss of interaction with the DOTIS element, however, PKA-dependent phosphorylation of alpha-crystallin is without effect on the interaction. It is hypothesized that the autophosphorylation of alpha-crystallin might be involved in regulatory mechanisms of the murine gamma D/E/F-crystallin gene expression.

Deletion of ultraconserved elements yields viable mice

Energy Technology Data Exchange (ETDEWEB)

Ahituv, Nadav; Zhu, Yiwen; Visel, Axel; Holt, Amy; Afzal, Veena; Pennacchio, Len A.; Rubin, Edward M.

2007-07-15

Ultraconserved elements have been suggested to retainextended perfect sequence identity between the human, mouse, and ratgenomes due to essential functional properties. To investigate thenecessities of these elements in vivo, we removed four non-codingultraconserved elements (ranging in length from 222 to 731 base pairs)from the mouse genome. To maximize the likelihood of observing aphenotype, we chose to delete elements that function as enhancers in amouse transgenic assay and that are near genes that exhibit markedphenotypes both when completely inactivated in the mouse as well as whentheir expression is altered due to other genomic modifications.Remarkably, all four resulting lines of mice lacking these ultraconservedelements were viable and fertile, and failed to reveal any criticalabnormalities when assayed for a variety of phenotypes including growth,longevity, pathology and metabolism. In addition more targeted screens,informed by the abnormalities observed in mice where genes in proximityto the investigated elements had been altered, also failed to revealnotable abnormalities. These results, while not inclusive of all thepossible phenotypic impact of the deleted sequences, indicate thatextreme sequence constraint does not necessarily reflect crucialfunctions required for viability.

Distribution patterns of elements in dental enamel of G. blacki: a preliminary dietary investigation using SRXRF

International Nuclear Information System (INIS)

Qu, Yating; Hu, Yaowu; Shang, Xue; Wang, Changsui; Jin, Changzhu; Zhang, Yingqi

2013-01-01

We measured the elemental mappings in dental enamel of Gigantopithecus blacki (n=3) using synchrotron radiation X-ray fluorescence (SRXRF) to understand the dietary variation during the time of tooth eruption. In order to account for the effects of diagenesis on the variation of elements in these fossil teeth, we compared the Fe and Mn elemental distribution and levels in dental enamel of G. blacki with that of a single modern pig tooth and found no differences. The observation of the variations of Sr, Ca and RE (rare earth elements) distribution in the incremental lines reveals that the plant foods utilized by G. blacki from the early Pleistocene or the middle Pleistocene had varied during the formation of dental enamel, possibly caused by the change of living environment or food resources. The variations of elemental distribution in different incremental lines are very promising to understand the nutritional and physical stress of G. blacki during the tooth eruption and environmental adaptations. (orig.)

Implementation of X-ray fluorescence microscopy for investigation of elemental abnormalities in central nervous system tissue

Energy Technology Data Exchange (ETDEWEB)

Chwiej, J. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland)]. E-mail: jchwiej@novell.ftj.agh.edu.pl; Szczerbowska-Boruchowska, M. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland); Wojcik, S. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland); Lankosz, M. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland); Chlebda, M. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland); Adamek, D. [Institute of Neurology, Collegium Medicum, Jagiellonian University, ul. Botaniczna-3, 31-503 Cracow (Poland); Tomik, B. [Institute of Neurology, Collegium Medicum, Jagiellonian University, ul. Botaniczna-3, 31-503 Cracow (Poland); Setkowicz, Z. [Department of Neuroanatomy, Institute of Zoology, Jagiellonian University, ul. Ingardena 6, 30-060 Cracow (Poland); Falkenberg, G. [Hamburger Synchrotronstrahlungslabor at Deutsches Elektronen-Synchrotron DESY, Notkestr. 85, Hamburg (Germany); Stegowski, Z. [Faculty of Physics and Applied Computer Science, AGH, University of Science and Technology, Al. Mickiewicza 30, 30-059 Cracow (Poland); Szczudlik, A. [Institute of Neurology, Collegium Medicum, Jagiellonian University, ul. Botaniczna-3, 31-503 Cracow (Poland)

2005-09-29

The microbeam synchrotron radiation X-ray fluorescence technique (micro-SRXRF) was applied to topographic and quantitative elemental analysis of human spinal cord tissue sections. The feasibility of this technique for the determination of elemental abnormalities caused by neurodegenerative disorder, i.e. amyotrophic lateral sclerosis (ALS), was verified. The applied measurement conditions allowed detecting: P, S, Cl, K, Ca, Fe, Cu, Zn and Br in thin tissue slices. Two-dimensional maps of the elemental distribution were recorded. Quantitative differences in elemental concentration between gray matter, nerve cells and white matter were observed for all analyzed cases. For the motor neuron bodies higher accumulation of S, Cl, K, Fe, Zn and Br was noticed. The results showed significant differences of elemental accumulation between the analyzed ALS cases. Moreover, the feasibility of using tissue sections fixed and embedded in paraffin for micro-SRXRF analysis was tested. These studies were performed on the samples of rat brain.

Distribution patterns of elements in dental enamel of G. blacki: a preliminary dietary investigation using SRXRF

Energy Technology Data Exchange (ETDEWEB)

Qu, Yating; Hu, Yaowu; Shang, Xue; Wang, Changsui [Chinese Academy of Sciences, Lab of Human Evolution, Institute of Vertebrate Paleontology and Paleoanthropology, Beijing (China); University of Chinese Academy of Sciences, Department of Scientific History and Archaeometry, School of Humanities, Beijing (China); Jin, Changzhu; Zhang, Yingqi [Chinese Academy of Sciences, Key Laboratory of Evolutionary Systematics of Vertebrates, Institute of Vertebrate Paleontology and Paleoanthropology, Beijing (China)

2013-04-15

We measured the elemental mappings in dental enamel of Gigantopithecus blacki (n=3) using synchrotron radiation X-ray fluorescence (SRXRF) to understand the dietary variation during the time of tooth eruption. In order to account for the effects of diagenesis on the variation of elements in these fossil teeth, we compared the Fe and Mn elemental distribution and levels in dental enamel of G. blacki with that of a single modern pig tooth and found no differences. The observation of the variations of Sr, Ca and RE (rare earth elements) distribution in the incremental lines reveals that the plant foods utilized by G. blacki from the early Pleistocene or the middle Pleistocene had varied during the formation of dental enamel, possibly caused by the change of living environment or food resources. The variations of elemental distribution in different incremental lines are very promising to understand the nutritional and physical stress of G. blacki during the tooth eruption and environmental adaptations. (orig.)

Distribution patterns of elements in dental enamel of G. blacki: a preliminary dietary investigation using SRXRF

Science.gov (United States)

Qu, Yating; Jin, Changzhu; Zhang, Yingqi; Hu, Yaowu; Shang, Xue; Wang, Changsui

2013-04-01

We measured the elemental mappings in dental enamel of Gigantopithecus blacki ( n=3) using synchrotron radiation X-ray fluorescence (SRXRF) to understand the dietary variation during the time of tooth eruption. In order to account for the effects of diagenesis on the variation of elements in these fossil teeth, we compared the Fe and Mn elemental distribution and levels in dental enamel of G. blacki with that of a single modern pig tooth and found no differences. The observation of the variations of Sr, Ca and RE (rare earth elements) distribution in the incremental lines reveals that the plant foods utilized by G. blacki from the early Pleistocene or the middle Pleistocene had varied during the formation of dental enamel, possibly caused by the change of living environment or food resources. The variations of elemental distribution in different incremental lines are very promising to understand the nutritional and physical stress of G. blacki during the tooth eruption and environmental adaptations.

Implementation of X-ray fluorescence microscopy for investigation of elemental abnormalities in central nervous system tissue

International Nuclear Information System (INIS)

Chwiej, J.; Szczerbowska-Boruchowska, M.; Wojcik, S.; Lankosz, M.; Chlebda, M.; Adamek, D.; Tomik, B.; Setkowicz, Z.; Falkenberg, G.; Stegowski, Z.; Szczudlik, A.

2005-01-01

The microbeam synchrotron radiation X-ray fluorescence technique (micro-SRXRF) was applied to topographic and quantitative elemental analysis of human spinal cord tissue sections. The feasibility of this technique for the determination of elemental abnormalities caused by neurodegenerative disorder, i.e. amyotrophic lateral sclerosis (ALS), was verified. The applied measurement conditions allowed detecting: P, S, Cl, K, Ca, Fe, Cu, Zn and Br in thin tissue slices. Two-dimensional maps of the elemental distribution were recorded. Quantitative differences in elemental concentration between gray matter, nerve cells and white matter were observed for all analyzed cases. For the motor neuron bodies higher accumulation of S, Cl, K, Fe, Zn and Br was noticed. The results showed significant differences of elemental accumulation between the analyzed ALS cases. Moreover, the feasibility of using tissue sections fixed and embedded in paraffin for micro-SRXRF analysis was tested. These studies were performed on the samples of rat brain

A 3D finite element model to investigate prosthetic interface stresses of different posterior tibial slope.

Science.gov (United States)

Shen, Yi; Li, Xiaomiao; Fu, Xiaodong; Wang, Weili

2015-11-01

Posterior tibial slope that is created during proximal tibial resection in total knee arthroplasty has emerged as an important factor in the mechanics of the knee joint and the surgical outcome. But the ideal degree of posterior tibial slope for recovery of the knee joint function and preventions of complications remains controversial and should vary in different racial groups. The objective of this paper is to investigate the effects of posterior tibial slope on contact stresses in the tibial polyethylene component of total knee prostheses. Three-dimensional finite element analysis was used to calculate contact stresses in tibial polyethylene component of total knee prostheses subjected to a compressive load. The 3D finite element model of total knee prosthesis was constructed from the images produced by 3D scanning technology. Stresses in tibial polyethylene component were calculated with four different posterior tibial slopes (0°, 3°, 6° and 9°). The 3D finite element model of total knee prosthesis we presented was well validated. We found that the stress distribution in the polythene as evaluated by the distributions of the von Mises stress, the maximum principle stress, the minimum principle stress and the Cpress were more uniform with 3° and 6° posterior tibial slopes than with 0° and 9° posterior tibial slopes. Moreover, the peaks of the above stresses and trends of changes with increasing degree of knee flexion were more ideal with 3° and 6° posterior slopes. The results suggested that the tibial component inclination might be favourable to 7°-10° so far as the stress distribution is concerned. The range of the tibial component inclination also can decrease the wear of polyethylene. Chinese posterior tibial slope is bigger than in the West, and the current domestic use of prostheses is imported from the West, so their demands to tilt back bone cutting can lead to shorten the service life of prostheses; this experiment result is of important

Synthesis and properties of superheavy elements

CERN Document Server

Hofmann, S

2003-01-01

The nuclear shell model predicts that the next doubly magic shell-closure beyond sup 2 sup 0 sup 8 Pb is at a proton number Z = 114, 120, or 126 and at a neutron number N = 172 or 184. The outstanding of experimental investigations is the exploration of this region of spherical 'SuperHeavy Elements' (SHEs). Experimental methods are described which allowed for the identification of elements 107 to 112 in studies of cold fusion reactions based on lead and bismuth targets. Also presented are data which were obtained on the synthesis of elements 112, 114, and 116 in investigation of hot fusion reactions using actinide targets. The decay data reveal that for the heaviest elements, the dominant decay mode is alpha emission, not fission. Decay properties as well as reaction cross- sections are compared with the results of theoretical studies. Finally, plans are presented for the further development of the experimental set-up and the application of new techniques. At a higher sensitivity, the exploration of the regio...

Influence of trace elements on fluoride uptake by teeth

Energy Technology Data Exchange (ETDEWEB)

Chaudhri, M A [Austin Hospital, Heidelberg (Australia). Dept. of Medical Physics; Melbourne Univ., Austin (Australia). Dept. of Medicine); Crawford, A [Melbourne Univ., Parkville (Australia). School of Physics

1981-03-01

To investigate the effect of various trace elements on fluoride uptake by teeth, the concentrations of F and other trace elements have been simultaneously determined in different regions of the teeth from children of South Australia. Teeth cross sectioned along the median plane have been used in these investigations, and their inside enamel, dentine and amelodentinal junctions investigated separately for the trace elemental composition. Fluoride has been determined by observing the 6-7 MeV gammas for the /sup 19/F(p,..cap alpha gamma..)/sup 16/O reaction, C by activation through the /sup 12/C(/sup 3/He,n)/sup 14/O reaction, while other trace elements have been measured by the thick target PIXE technique. Linear correlation coefficients have been calculated between the F concentrations in teeth and those of other trace elements observed. Fluoride is found to correlate best with C, Cu and Pb, poorly with Fe, Sr, Ni and Ag, while with Br and Zn it has-ve coefficients. Student's t-test has been applied to the data to examine the significance of the variation of Fand other trace elements amongst different dental tissues from healthy and diseased teeth.

Serum Concentrations of Trace Elements in Patients with Tuberculosis and Its Association with Treatment Outcome

Directory of Open Access Journals (Sweden)

Rihwa Choi

2015-07-01

Full Text Available Deficiencies in essential trace elements are associated with impaired immunity in tuberculosis infection. However, the trace element concentrations in the serum of Korean patients with tuberculosis have not yet been investigated. This study aimed to compare the serum trace element concentrations of Korean adult patients with tuberculosis with noninfected controls and to assess the impact of serum trace element concentration on clinical outcome after antituberculosis treatment. The serum concentrations of four trace elements in 141 consecutively recruited patients with tuberculosis and 79 controls were analyzed by inductively coupled plasma-mass spectrometry. Demographic characteristics were also analyzed. Serum cobalt and copper concentrations were significantly higher in patients with tuberculosis compared with controls, while zinc and selenium concentrations were significantly lower (p < 0.01. Moreover, serum selenium and zinc concentrations were positively correlated (ρ = 0.41, p < 0.05. A high serum copper concentration was associated with a worse clinical outcome, as assessed after one month of antituberculosis therapy. Specifically, culture-positive patients had higher serum copper concentrations than culture-negative patients (p < 0.05. Patients with tuberculosis had altered serum trace element concentrations. Further research is needed to elucidate the roles of individual trace elements and to determine their clinical impact on patients with tuberculosis.

Accuracy of specimen-specific nonlinear finite element analysis for evaluation of distal radius strength in cadaver material.

Science.gov (United States)

Matsuura, Yusuke; Kuniyoshi, Kazuki; Suzuki, Takane; Ogawa, Yasufumi; Sukegawa, Koji; Rokkaku, Tomoyuki; Takahashi, Kazuhisa

2014-11-01

Distal radius fracture, which often occurs in the setting of osteoporosis, can lead to permanent deformity and disability. Great effort has been directed toward developing noninvasive methods for evaluating the distal radius strength, with the goal of assessing fracture risk. The aim of this study was to evaluate distal radius strength using a finite element model and to gauge the accuracy of finite element model measurement using cadaver material. Ten wrists were obtained from cadavers with a mean age of 89.5 years at death. CT images of each wrist in an extended position were obtained. CT-based finite element models were prepared with Mechanical Finder software. Fracture on the models was simulated by applying a mechanical load to the palm in a direction parallel to the forearm axis, after which the fracture load and the site at which the fracture began were identified. For comparison, the wrists were fractured using a universal testing machine and the fracture load and the site of fracture were identified. The fracture load was 970.9 N in the finite element model group and 990.0 N in the actual measurement group. The site of the initial fracture was extra-articular to the distal radius in both groups. The finite element model was predictive for distal radius fracture when compared to the actual measurement. In this study, a finite element model for evaluation of distal radius strength was validated and can be used to predict fracture risk. We conclude that a finite element model is useful for the evaluation of distal radius strength. Knowing distal radius strength might avoid distal radius fracture because appropriate antiosteoporotic treatment can be initiated.

Novel porcine repetitive elements

Directory of Open Access Journals (Sweden)

Nonneman Dan J

2006-12-01

Full Text Available Abstract Background Repetitive elements comprise ~45% of mammalian genomes and are increasingly known to impact genomic function by contributing to the genomic architecture, by direct regulation of gene expression and by affecting genomic size, diversity and evolution. The ubiquity and increasingly understood importance of repetitive elements contribute to the need to identify and annotate them. We set out to identify previously uncharacterized repetitive DNA in the porcine genome. Once found, we characterized the prevalence of these repeats in other mammals. Results We discovered 27 repetitive elements in 220 BACs covering 1% of the porcine genome (Comparative Vertebrate Sequencing Initiative; CVSI. These repeats varied in length from 55 to 1059 nucleotides. To estimate copy numbers, we went to an independent source of data, the BAC-end sequences (Wellcome Trust Sanger Institute, covering approximately 15% of the porcine genome. Copy numbers in BAC-ends were less than one hundred for 6 repeat elements, between 100 and 1000 for 16 and between 1,000 and 10,000 for 5. Several of the repeat elements were found in the bovine genome and we have identified two with orthologous sites, indicating that these elements were present in their common ancestor. None of the repeat elements were found in primate, rodent or dog genomes. We were unable to identify any of the replication machinery common to active transposable elements in these newly identified repeats. Conclusion The presence of both orthologous and non-orthologous sites indicates that some sites existed prior to speciation and some were generated later. The identification of low to moderate copy number repetitive DNA that is specific to artiodactyls will be critical in the assembly of livestock genomes and studies of comparative genomics.

The elements of life and medicines.

Science.gov (United States)

Chellan, Prinessa; Sadler, Peter J

2015-03-13

Which elements are essential for human life? Here we make an element-by-element journey through the periodic table and attempt to assess whether elements are essential or not, and if they are, whether there is a relevant code for them in the human genome. There are many difficulties such as the human biochemistry of several so-called essential elements is not well understood, and it is not clear how we should classify elements that are involved in the destruction of invading microorganisms, or elements which are essential for microorganisms with which we live in symbiosis. In general, genes do not code for the elements themselves, but for specific chemical species, i.e. for the element, its oxidation state, type and number of coordinated ligands, and the coordination geometry. Today, the biological periodic table is in a position somewhat similar to Mendeleev's chemical periodic table of 1869: there are gaps and we need to do more research to fill them. The periodic table also offers potential for novel therapeutic and diagnostic agents, based on not only essential elements, but also non-essential elements, and on radionuclides. Although the potential for inorganic chemistry in medicine was realized more than 2000 years ago, this area of research is still in its infancy. Future advances in the design of inorganic drugs require more knowledge of their mechanism of action, including target sites and metabolism. Temporal speciation of elements in their biological environments at the atomic level is a major challenge, for which new methods are urgently needed.

A Novel Collection of snRNA-Like Promoters with Tissue-Specific Transcription Properties

Directory of Open Access Journals (Sweden)

Aldo Pagano

2012-09-01

Full Text Available We recently identified a novel dataset of snRNA-like trascriptional units in the human genome. The investigation of a subset of these elements showed that they play relevant roles in physiology and/or pathology. In this work we expand our collection of small RNAs taking advantage of a newly developed algorithm able to identify genome sequence stretches with RNA polymerase (pol III type 3 promoter features thus constituting putative pol III binding sites. The bioinformatic analysis of a subset of these elements that map in introns of protein-coding genes in antisense configuration suggest their association with alternative splicing, similarly to other recently characterized small RNAs. Interestingly, the analysis of the transcriptional activity of these novel promoters shows that they are active in a cell-type specific manner, in accordance with the emerging body of evidence of a tissue/cell-specific activity of pol III.

Diffractive elements performance in chromatic confocal microscopy

International Nuclear Information System (INIS)

Garzon, J; Duque, D; Alean, A; Toledo, M; Meneses, J; Gharbi, T

2011-01-01

The Confocal Laser Scanning Microscopy (CLSM) has been widely used in the semiconductor industry and biomedicine because of its depth discrimination capability. Subsequent to this technique has been developed in recent years Chromatic Confocal Microscopy. This method retains the same principle of confocal and offers the added advantage of removing the axial movement of the moving system. This advantage is usually accomplished with an optical element that generates a longitudinal chromatic aberration and a coding system that relates the axial position of each point of the sample with the wavelength that is focused on each. The present paper shows the performance of compact chromatic confocal microscope when some different diffractive elements are used for generation of longitudinal chromatic aberration. Diffractive elements, according to the process and manufacturing parameters, may have different diffraction efficiency and focus a specific wavelength in a specific focal position. The performance assessment is carried out with various light sources which exhibit an incoherent behaviour and a broad spectral width.

Investigations of some elements distribution in dental tissues by INAA as a function of ecological and some other parameters

International Nuclear Information System (INIS)

Draskovic, R.J.; Jacimovic, Lj.; Stojicevic, M.; Pajic, P.; Filipovic, V.

1982-01-01

Distribution of some elements (Hg, Zn, Sb, Co and Sc) in dental tissues (enamel, dentine, pulp) has been investiaated by instrumental neutron activation analysis (INAA). Teeth samples were taken from patients living in different regions (mine and mineralized areas, plain), taking into account the following parameters: ecological conditions, age of patients, stomatological operations and use of local cosmetic preparations containig mercury. Samples of vegetation (beech, moss, pine) from two locations belonging to regions of mineralized areas also were analyzed. Results of our investigations are presented and discussed. (author)

Rare Earth Elements Distribution in Beryl

International Nuclear Information System (INIS)

El Gawish, H.K.; Nada, N.; Ghaly, W.A.; Helal, A.I.

2012-01-01

Laser ablation method is applied to a double focusing inductively coupled plasma mass spectrometer to determine the rare earth element distribution in some selected beryl samples. White, green and blue beryl samples are selected from the Egyptian eastern desert. Distributions of chondrite- normalized plot for the rare earth element in the selected beryl samples are investigated

Investigation on the status of rare earth elements contained in the powder of spent fluorescent lamps

International Nuclear Information System (INIS)

Belardi, G.; Ippolito, N.; Piga, L.; Serracino, M.

2014-01-01

Highlights: • Most of rare earth elements are contained in particles of size finer than 7 μm. • Most of Si, K and Na are contained in the coarser size-fractions. • The phases in the size-fractions of the fluorescent powder have been determined. • Europium is contained in yttrium oxide and in vanadium–yttrium oxides. • The crystallo–chemical composition of all the phases has been determined. - Abstract: The aim of this study is to examine the status of rare earth elements (REE) contained in the chemical compounds that make up the powder of spent fluorescent lamps, with a view of their recovery. The status of REE in the as-received powder, as well as in a few size-class fractions of it, has been established. This way, only those size-class fractions containing high REE concentrations can be considered in a recovery process. The investigation has been carried out using particle-size, chemical, TGA/DTA, XRPD, SEM-EDS and EMPA analyses. The last technique enabled to establish the status of REE within the lattice of the chemical compounds present in the powder. The fineness of the as-received powder and the higher REE concentration in the finest size-classes suggest that physical methods of separation should not be used to separate the REE-containing chemical compounds from each other. Leaching methods seem more suitable with a material of such size

Fundamental and methodological investigations for the improvement of elemental analysis by inductively coupled plasma mass soectrometry

Energy Technology Data Exchange (ETDEWEB)

Ebert, Christopher Hysjulien [Ames Lab., Ames, IA (United States)

2012-01-01

This dissertation describes a variety of studies meant to improve the analytical performance of inductively coupled plasma mass spectrometry (ICP-MS) and laser ablation (LA) ICP-MS. The emission behavior of individual droplets and LA generated particles in an ICP is studied using a high-speed, high frame rate digital camera. Phenomena are observed during the ablation of silicate glass that would cause elemental fractionation during analysis by ICP-MS. Preliminary work for ICP torch developments specifically tailored for the improvement of LA sample introduction are presented. An abnormal scarcity of metal-argon polyatomic ions (MAr{sup +}) is observed during ICP-MS analysis. Evidence shows that MAr{sup +} ions are dissociated by collisions with background gas in a shockwave near the tip of the skimmer cone. Method development towards the improvement of LA-ICP-MS for environmental monitoring is described. A method is developed to trap small particles in a collodion matrix and analyze each particle individually by LA-ICP-MS.

Walking the cod: an investigation into the relative robustness of cod, Gadus morhua, skeletal elements

Directory of Open Access Journals (Sweden)

Andrew K.G. Jones

1999-12-01

Full Text Available A simple experiment is described which details what happens to the bones of cod when they are walked on by a man. The pattern of fragmentation for various elements is illustrated and an index of robustness proposed for those elements in a cod skeleton most frequently recovered from archaeological sites.

Parametric study of unconstrained high-pressure torsion- Finite element analysis

International Nuclear Information System (INIS)

Halloumi, A; Busquet, M; Descartes, S

2014-01-01

The high-pressure torsion (HPT) experiments have been investigated numerically. An axisymmetric model with twist was developed with commercial finite element software (Abaqus) to study locally the specificity of the stress and strain history within the transformed layers produced during HPT processing. The material local behaviour law in the plastic domain was modelled. A parametric study highlights the role of the imposed parameters (friction coefficient at the interfaces anvil surfaces/sample, imposed pressure) on the stress/strain distribution in the sample bulk for two materials: ultra-high purity iron and steel grade R260. The present modelling provides a tool to investigate and to analyse the effect of pressure and friction on the local stress and strain history during the HPT process and to couple with experimental results

Development and testing of the EDF-2 reactor fuel element

International Nuclear Information System (INIS)

Delpeyroux, P.

1964-01-01

This technical report reviews the work which has been necessary for defining the EDF-2 fuel element. After giving briefly the EDF-2 reactor characteristics and the preliminary choice of parameters which made it possible to draw up a draft plan for the fuel element, the authors consider the research proper: - Uranium studies: tests on the passage into the β phase of an internal crown of a tube, bending of the tube under the effect of a localized force, welding of the end-pellets and testing for leaks. The resistance of the tube to crushing and of the pellets to yielding under the external pressure have been studied in detail in another CEA report. - Can studies: conditions of production and leak proof testing of the can, resistance of the fins to creep due to the effect of the gas flow. - Studies of the extremities of the element: creep under compression and welding of the plugs to the can. - Cartridge studies: determination of the characteristics of the can fuel fixing grooves and of the canning conditions, verification of the resistance of the fuel element to thermal cycling, determination of the temperature drop at the can-fuel interface dealt with in more detail in another CEA report. - Studies of the whole assembly: this work which concerns the graphite jacket, the support and the cartridge vibrations has been carried out by the Mechanical and Thermal Study Service (Mechanics Section). In this field the Fuel Element Study Section has investigated the behaviour of the centering devices in a gas current. The outcome of this research is the defining of the plan of the element the production process and the production specifications. The validity of ail these out-of-pile tests will be confirmed by the in-pile tests already under way and by irradiation of the elements in the EDF-2 reactor itself. In conclusion the programme is given for improving the fuel element and for defining the fuel element for the second charge. (authors) [fr

Fabrication of fuel elements interplay between typical SNR Mark Ia specifications and the fuel element fabrication

International Nuclear Information System (INIS)

Biermann, W.K.; Heuvel, H.J.; Pilate, S.; Vanderborck, Y.; Pelckmans, E.; Vanhellemont, G.; Roepenack, H.; Stoll, W.

1987-01-01

The core and fuel were designed for the SNR-300 first core by Interatom GmbH and Belgonucleaire. The fuel was fabricated by Alkem/RBU and Belgonucleaire. Based on the preparation of drawings and specifications and on the results of the prerun fabrication, an extensive interplay took place between design requirements, specifications, and fabrication processes at both fuel plants. During start-up of pellet and pin fabrication, this solved such technical questions as /sup 239/Pu equivalent linear weight, pellet density, stoichiometry of the pellets, and impurity content. Close cooperation of designers and manufacturers has allowed manufacture of 205 fuel assemblies without major problems

A compact, in vivo screen of all 6-mers reveals drivers of tissue-specific expression and guides synthetic regulatory element design.

Science.gov (United States)

Smith, Robin P; Riesenfeld, Samantha J; Holloway, Alisha K; Li, Qiang; Murphy, Karl K; Feliciano, Natalie M; Orecchia, Lorenzo; Oksenberg, Nir; Pollard, Katherine S; Ahituv, Nadav

2013-07-18

Large-scale annotation efforts have improved our ability to coarsely predict regulatory elements throughout vertebrate genomes. However, it is unclear how complex spatiotemporal patterns of gene expression driven by these elements emerge from the activity of short, transcription factor binding sequences. We describe a comprehensive promoter extension assay in which the regulatory potential of all 6 base-pair (bp) sequences was tested in the context of a minimal promoter. To enable this large-scale screen, we developed algorithms that use a reverse-complement aware decomposition of the de Bruijn graph to design a library of DNA oligomers incorporating every 6-bp sequence exactly once. Our library multiplexes all 4,096 unique 6-mers into 184 double-stranded 15-bp oligomers, which is sufficiently compact for in vivo testing. We injected each multiplexed construct into zebrafish embryos and scored GFP expression in 15 tissues at two developmental time points. Twenty-seven constructs produced consistent expression patterns, with the majority doing so in only one tissue. Functional sequences are enriched near biologically relevant genes, match motifs for developmental transcription factors, and are required for enhancer activity. By concatenating tissue-specific functional sequences, we generated completely synthetic enhancers for the notochord, epidermis, spinal cord, forebrain and otic lateral line, and show that short regulatory sequences do not always function modularly. This work introduces a unique in vivo catalog of short, functional regulatory sequences and demonstrates several important principles of regulatory element organization. Furthermore, we provide resources for designing compact, reverse-complement aware k-mer libraries.

Superheavy-element spectroscopy: Correlations along element 115 decay chains

Science.gov (United States)

Rudolph, D.; Forsberg, U.; Sarmiento, L. G.; Golubev, P.; Fahlander, C.

2016-05-01

Following a brief summary of the region of the heaviest atomic nuclei yet created in the laboratory, data on more than hundred α-decay chains associated with the production of element 115 are combined to investigate time and energy correlations along the observed decay chains. Several of these are analysed using a new method for statistical assessments of lifetimes in sets of decay chains.

Site specific study for possible ongoing salt dome movement

International Nuclear Information System (INIS)

Thoms, R.L.; Manning, T.A.; Paille, L.K.; Gehle, R.M.

1977-01-01

U.S. Gulf Coast salt domes, among other geologic structures, currently are being considered for storage of commercial radioactive wastes. A major concern with dome storage of long lived radioactive wastes lies with the possible tectonic movement of the host dome. Any ongoing movement of a salt dome can be monitored with a site specific complementary system of field instrumentation and finite element modelling. Field instrumentation and accompanying finite element analyses for a study dome in northwest Louisiana are described. Site specific data and early experience associated with tiltmeters over the dome are presented. Also, recommendations are made for modifications and extensions of the field instrumentation and finite element modelling appropriate to the specific site under study

Site-specific investigations of aquifer thermal energy storage for space and process cooling

International Nuclear Information System (INIS)

Brown, D.R.

1991-01-01

This paper reports on the Pacific Northwest Laboratory (PNL) that has completed three preliminary site-specific feasibility studies that investigated aquifer thermal energy storage (ATES) for reducing space and process cooling costs. Chilled water stored in an ATES system could be used to meet all or part of the process and/or space cooling loads at the three facilities investigated. Seasonal or diurnal chill ATES systems could be significantly less expensive than a conventional electrically-driven, load-following chiller system at one of the three sites, depending on the cooling water loop return temperature and presumed future electricity escalation rate. For the other two sites investigated, a chill ATES system would be economically competitive with conventional chillers if onsite aquifer characteristics were improved. Well flow rates at one of the sites were adequate, but the expected thermal recovery efficiency was too low. The reverse of this situation was found at the other site, where the thermal recovery efficiency was expected to be adequate, but well flow rates were too low

Investigation of the Reliability of Bridge Elements Reinforced with Basalt Plastic Fibers

Science.gov (United States)

Koval', T. I.

2017-09-01

The poorly studied problem on the reliability and durability of basalt-fiber-reinforced concrete bridge elements is considered. A method of laboratory research into the work of specimens of the concrete under a manyfold cyclic dynamic load is proposed. The first results of such experiments are presented.

Patient-Specific Computational Modeling

CERN Document Server

Peña, Estefanía

2012-01-01

This book addresses patient-specific modeling. It integrates computational modeling, experimental procedures, imagine clinical segmentation and mesh generation with the finite element method (FEM) to solve problems in computational biomedicine and bioengineering. Specific areas of interest include cardiovascular problems, ocular and muscular systems and soft tissue modeling. Patient-specific modeling has been the subject of serious research over the last seven years and interest in the area is continually growing and this area is expected to further develop in the near future.

Material specific lateralization of medial temporal lobe function: An fMRI investigation.

Science.gov (United States)

Dalton, Marshall A; Hornberger, Michael; Piguet, Olivier

2016-03-01

The theory of material specific lateralization of memory function posits that left and right MTL regions are asymmetrically involved in mnemonic processing of verbal and nonverbal material respectively. Lesion and functional imaging (fMRI) studies provide robust evidence for a left MTL asymmetry in the verbal memory domain. Evidence for a right MTL/nonverbal asymmetry is not as robust. A handful of fMRI studies have investigated this issue but have generally utilised nonverbal stimuli which are amenable to semantic elaboration. This fMRI study aimed to investigate the neural correlates of recognition memory processing in 20 healthy young adults (mean age = 26 years) for verbal stimuli and nonverbal stimuli that were specifically designed to minimize verbalisation. Analyses revealed that the neural correlates of recognition memory processing for verbal and nonverbal stimuli were differentiable and asymmetrically recruited the left and right MTL respectively. The right perirhinal cortex and hippocampus were preferentially involved in successful recognition memory of items devoid of semantic information. In contrast, the left anterior hippocampus was preferentially involved in successful recognition memory of stimuli which contained semantic meaning. These results suggest that the left MTL is preferentially involved in mnemonic processing of verbal/semantic information. In contrast, the right MTL is preferentially involved in visual/non-semantic mnemonic processing. We propose that during development, the left MTL becomes specialised for verbal mnemonic processing due to its proximity with left lateralised cortical language processing areas while visual/non-semantic mnemonic processing gets 'crowded out' to become predominantly, but not completely, the domain of the right MTL. © 2015 Wiley Periodicals, Inc.

Constructing disease-specific gene networks using pair-wise relevance metric: Application to colon cancer identifies interleukin 8, desmin and enolase 1 as the central elements

Directory of Open Access Journals (Sweden)

Jiang Wei

2008-08-01

Full Text Available Abstract Background With the advance of large-scale omics technologies, it is now feasible to reversely engineer the underlying genetic networks that describe the complex interplays of molecular elements that lead to complex diseases. Current networking approaches are mainly focusing on building genetic networks at large without probing the interaction mechanisms specific to a physiological or disease condition. The aim of this study was thus to develop such a novel networking approach based on the relevance concept, which is ideal to reveal integrative effects of multiple genes in the underlying genetic circuit for complex diseases. Results The approach started with identification of multiple disease pathways, called a gene forest, in which the genes extracted from the decision forest constructed by supervised learning of the genome-wide transcriptional profiles for patients and normal samples. Based on the newly identified disease mechanisms, a novel pair-wise relevance metric, adjusted frequency value, was used to define the degree of genetic relationship between two molecular determinants. We applied the proposed method to analyze a publicly available microarray dataset for colon cancer. The results demonstrated that the colon cancer-specific gene network captured the most important genetic interactions in several cellular processes, such as proliferation, apoptosis, differentiation, mitogenesis and immunity, which are known to be pivotal for tumourigenesis. Further analysis of the topological architecture of the network identified three known hub cancer genes [interleukin 8 (IL8 (p ≈ 0, desmin (DES (p = 2.71 × 10-6 and enolase 1 (ENO1 (p = 4.19 × 10-5], while two novel hub genes [RNA binding motif protein 9 (RBM9 (p = 1.50 × 10-4 and ribosomal protein L30 (RPL30 (p = 1.50 × 10-4] may define new central elements in the gene network specific to colon cancer. Gene Ontology (GO based analysis of the colon cancer-specific gene network and

Constructing disease-specific gene networks using pair-wise relevance metric: application to colon cancer identifies interleukin 8, desmin and enolase 1 as the central elements.

Science.gov (United States)

Jiang, Wei; Li, Xia; Rao, Shaoqi; Wang, Lihong; Du, Lei; Li, Chuanxing; Wu, Chao; Wang, Hongzhi; Wang, Yadong; Yang, Baofeng

2008-08-10

With the advance of large-scale omics technologies, it is now feasible to reversely engineer the underlying genetic networks that describe the complex interplays of molecular elements that lead to complex diseases. Current networking approaches are mainly focusing on building genetic networks at large without probing the interaction mechanisms specific to a physiological or disease condition. The aim of this study was thus to develop such a novel networking approach based on the relevance concept, which is ideal to reveal integrative effects of multiple genes in the underlying genetic circuit for complex diseases. The approach started with identification of multiple disease pathways, called a gene forest, in which the genes extracted from the decision forest constructed by supervised learning of the genome-wide transcriptional profiles for patients and normal samples. Based on the newly identified disease mechanisms, a novel pair-wise relevance metric, adjusted frequency value, was used to define the degree of genetic relationship between two molecular determinants. We applied the proposed method to analyze a publicly available microarray dataset for colon cancer. The results demonstrated that the colon cancer-specific gene network captured the most important genetic interactions in several cellular processes, such as proliferation, apoptosis, differentiation, mitogenesis and immunity, which are known to be pivotal for tumourigenesis. Further analysis of the topological architecture of the network identified three known hub cancer genes [interleukin 8 (IL8) (p approximately 0), desmin (DES) (p = 2.71 x 10(-6)) and enolase 1 (ENO1) (p = 4.19 x 10(-5))], while two novel hub genes [RNA binding motif protein 9 (RBM9) (p = 1.50 x 10(-4)) and ribosomal protein L30 (RPL30) (p = 1.50 x 10(-4))] may define new central elements in the gene network specific to colon cancer. Gene Ontology (GO) based analysis of the colon cancer-specific gene network and the sub-network that

Investigation of metal elements in cataract patients using hair samples

International Nuclear Information System (INIS)

Verma, Manjula; Nath Verma, Vishwa

2008-01-01

This investigation is confined to the study of hair samples from cataract victims. Hair mineral analysis is an analytical test, which measures the mineral content of the hair. The main purpose of this research is to make a relationship between the deposition of metals (listed above) and that of human cataract. This research is carried out on the basis to check for the imbalance of these metals deposited in the human body. These hair samples underwent normal acid digestion and atomic absorption for each metal was taken. As a result the concentrations of these metals were further analyzed to make a proper justification of the various metals that was assessed lead, zinc, magnesium and iron said to be the most predominant in relation to the other metals that was analyzed. The deposition of these metals in high concentration does not necessary mean that they are not the main reason for the development of human cataract.The sampled hair, obtained by cutting the first inch and one-half growth closest to the scalp at the nape of the neck or other part of the body. Testing is then performed using highly sophisticated detection equipment such Atomic Absorption Spectroscopy to achieve the most accurate precise results. These elements were analyzed using a Varian 20 plus Atomic Absorption Spectrometer. Approximately 0.1 g of the hair sample was placed at the bottom of a 250 ml round bottom flask which was attached to a reflux condenser. The sample was digested with 4 ml H2 SO4 (98%) and 4 ml HNO3 (69%) on moderate heat for approximately 30 minutes or until the hair was completely dissolved to a yellow solution. 3 ml of 30% hydrogen peroxide (H2O2) were then added and the mixture was heated for 30 minutes to clear the solution. Various metals such as lead, zinc, copper, cadmium, magnesium, iron, chromium and cobalt were tested for in the hair sample of cataract patients using atomic absorption spectrometry. (Author)

INVESTIGATION OF HYDROELASTIC BEHAVIOR OF A PONTOON-TYPE VLFS DURING UNSTEADY EXTERNAL LOADS IN WAVE CONDITION USING A HYBRID FINITE ELEMENT-BOUNDARY ELEMENT (FE-ME METHOD

Directory of Open Access Journals (Sweden)

Yong Cheng

2017-01-01

Full Text Available The hydroelastic behaviour of a pontoon-type VLFS subjected to unsteady external loads in wave condition is investigated in the context of the time-domain modal expansion theory, in which the boundary element method (BEM based on time domain Kelvin sources is used for hydrodynamic forces and the finite element method (FEM is adopted for solving the deflections of the VLFS. In this analysis, the interpolation-tabulation scheme is applied to assess rapidly and accurately the free-surface Green function in finite water depth, and the boundary integral equation of a quarter VLFS model is further established taking advantage of symmetry of flow field and structure. The VLFS is modelled as an equivalent solid plate based on the Mindlin plate theory. The coupled plate-water model is performed to determine the wave-induced responses and transient behaviour under external loads such as a huge mass impact onto the structure and moving loads of an airplane, respectively. These results are verified with existing numerical results and experimental test. Then, the developed numerical tools are used in the study of the combined action taking into account of the mass drop/airplane landing as well as forward or reverse incident wave action. The deflections of the runway, the time history of vertical positions and the trajectory of the airplane are also presented through a systematic time-domain simulation, which illustrates the usefulness of the presently developed numerical solutions.

Electromagnetic matrix elements in baryons

International Nuclear Information System (INIS)

Lipkin, H.J.; Moinester, M.A.

1992-01-01

Some simple symmetry relations between matrix elements of electromagnetic operators are investigated. The implications are discussed for experiments to study hyperon radiative transitions and polarizabilities and form factors. (orig.)

Quality assurance of fuel elements

International Nuclear Information System (INIS)

Hoerber, J.

1980-01-01

The quality assurance activities for reactor fuel elements are based on a quality assurance system which implies the requirements resulting from the specifications, regulations of the authorities, national standards and international rules and regulations. The quality assurance related to production of reactor fuel will be shown for PWR fuel elements in all typical fabrication steps as conversion into UO 2 -powder, pelletizing, rodmanufacture and assembling. A wide range of destructive and nondestructive techniques is applied. Quality assurance is not only verified by testing techniques but also by process monitoring by means of parameter control in production and testing procedures. (RW)

Binding energy, phonon spectra and thermodynamic properties of elements with type structures A1 (Al, Cu), A2 (V, Ti2), A3 (Mg, Tiβ), A4 (Si, Sn)

International Nuclear Information System (INIS)

Sirota, N.N.; Soshnina, T.M.; Sirota, I.M.; Sokolovskij, T.D.

2001-01-01

One calculated dependences of binding energy on spacing between the nearest atoms of Al and Cu elements with A 1 type structure, of V and Ti α elements with A 2 type structure, of Mg and Ti β elements with A 3 type structure, Si and Sn elements with A 4 type structure. To calculate one applied the methods based on the Thomas-Fermi statistic theory of atom. The derived dependences were approximated using the expression in the form of the Mie-Grueneisen potential. On the basis of the Born-von-Karman model of solid body one calculated the phonon spectra using which one determined temperature dependences of specific heat, free and internal energy of the investigated elements. The calculated values of energy of atomization, equilibrium closest interatomic spacing and temperature dependences of specific heat are in compliance with the experimental data [ru

Identification of hookworm DAF-16/FOXO response elements and direct gene targets.

Directory of Open Access Journals (Sweden)

Xin Gao

2010-08-01

Full Text Available The infective stage of the parasitic nematode hookworm is developmentally arrested in the environment and needs to infect a specific host to complete its life cycle. The canine hookworm (Ancylostoma caninum is an excellent model for investigating human hookworm infections. The transcription factor of A. caninum, Ac-DAF-16, which has a characteristic fork head or "winged helix" DNA binding domain (DBD, has been implicated in the resumption of hookworm development in the host. However, the precise roles of Ac-DAF-16 in hookworm parasitism and its downstream targets are unknown. In the present study, we combined molecular techniques and bioinformatics to identify a group of Ac-DAF-16 binding sites and target genes.The DNA binding domain of Ac-DAF-16 was used to select genomic fragments by in vitro genomic selection. Twenty four bound genomic fragments were analyzed for the presence of the DAF-16 family binding element (DBE and possible alternative Ac-DAF-16 bind motifs. The 22 genes linked to these genomic fragments were identified using bioinformatics tools and defined as candidate direct gene targets of Ac-DAF-16. Their developmental stage-specific expression patterns were examined. Also, a new putative DAF-16 binding element was identified.Our results show that Ac-DAF-16 is involved in diverse biological processes throughout hookworm development. Further investigation of these target genes will provide insights into the molecular basis by which Ac-DAF-16 regulates its downstream gene network in hookworm infection.

Research and development of optic fiber sensitive elements for fatigue gauges

International Nuclear Information System (INIS)

Rakhimov, N.R.; Shamirzaev, S.Kh.

2004-01-01

In the work a possibility for using the optic fibers as the sensitive element for the fatigue gauge of mechanical construction elements is investigated. The experimental results are presented on investigation of polymer optic fibers subjected to the fatigue loads using the special tools. It was shown that they have a high sensitivity to fatigue damage of construction elements. (author)

Finite Element Analysis of Pipe T-Joint

OpenAIRE

P.M.Gedkar; Dr. D.V. Bhope

2012-01-01

This paper reports stress analysis of two pressurized cylindrical intersection using finite element method. The different combinations of dimensions of run pipe and the branch pipe are used to investigate thestresses in pipe at the intersection. In this study the stress analysis is accomplished by finite element package ANSYS.

Fluid element in SAP IV

International Nuclear Information System (INIS)

Yilmaz, C.; Akkas, N.

1979-01-01

In previous studies a fluid element is incorporated in the widely used general purpose finite element program SAPIV. This type of problem is of interest in the design of nuclear components involving geometric complexities and nonlinearities. The elasticity matrix of a general-purpose finite element program is modified in such a way that it becomes possible to idealize fluid as a structural finite element with zero shear modulus and a given bulk modules. Using the modified version of SAPIV, several solid-fluid interactions problems are solved. The numerical solutions are compared with the available analytical solutions. They are shown to be in reasonable aggrement. It is also shown that by solving an exterior-fluid interaction problem, the pressure wave propagation in the acoustic medium can be solved with the same approach. In this study, two of the problem not studied in the previous work will be presented. These problems are namely the effects of the link elements used at solid-fluid interfaces and of the concentrated loads on the response of the fluid medium. Truss elements are used as the link elements. After these investigations, it is decided that general purpose finite element programs with slight modifications can be used in the safety analysis of nuclear reactor plants. By this procedure it is possible to handle two-dimensional plane strain and tridimensional axisymmetric problems of this type. (orig.)

Applications of Lagrangian Dispersion Modeling to the Analysis of Changes in the Specific Absorption of Elemental Carbon

Energy Technology Data Exchange (ETDEWEB)

Doran, J. C.; Fast, Jerome D.; Barnard, James C.; Laskin, Alexander; Desyaterik, Yury; Gilles, Marry K.; Hopkins, Rebecca J.

2008-03-07

We use a Lagrangian dispersion model driven by a mesoscale model with four-dimensional data assimilation to simulate the dispersion of elemental carbon (EC) over a region encompassing Mexico City and its surroundings, the study domain for the 2006 MAX-MEX experiment, which was a component of the MILAGRO campaign. The results are used to identify periods when biomass burning was likely to have had a significant impact on the concentrations of elemental carbon at two sites, T1 and T2, downwind of the city, and when emissions from the Mexico City Metropolitan Area (MCMA) were likely to have been more important. They are also used to estimate the median ages of EC affecting the specific absorption of light, aABS, at 870 nm as well as to identify periods when the urban plume from the MCMA was likely to have been advected over T1 and T2. Values of aABS at T1, the nearer of the two sites to Mexico City, were smaller at night and increased rapidly after mid-morning, peaking in the mid-afternoon. The behavior is attributed to the coating of aerosols with substances such as sulfate or organic carbon during daylight hours, but such coating appears to be limited or absent at night. Evidence for this is provided by scanning electron microscope images of aerosols collected at three sampling sites. During daylight hours the values of aABS did not increase with aerosol age for median ages in the range of 1-4 hours. There is some evidence for absorption increasing as aerosols were advected from T1 to T2 but the statistical significance of that result is not strong.

Structural elements recognized by abacavir-induced T cells

DEFF Research Database (Denmark)

Yerly, Daniel; Pompeu, Yuri Andreiw; Schutte, Ryan J.

2017-01-01

of autoimmune destruction. The structural elements recognized by drug-specific T cell receptors (TCRs) in vivo are poorly defined. Drug-stimulated T cells express TCRs specific for peptide/HLA complexes, but the characteristics of peptides (sequence, or endogenous or exogenous origin) presented in the context...

Investigating Rare Earth Element Systematics in the Marcellus Shale

Science.gov (United States)

Yang, J.; Torres, M. E.; Kim, J. H.; Verba, C.

2014-12-01

The lanthanide series of elements (the 14 rare earth elements, REEs) have similar chemical properties and respond to different chemical and physical processes in the natural environment by developing unique patterns in their concentration distribution when normalized to an average shale REE content. The interpretation of the REE content in a gas-bearing black shale deposited in a marine environment must therefore take into account the paleoredox conditions of deposition as well as any diagenetic remobilization and authigenic mineral formation. We analyzed 15 samples from a core of the Marcellus Shale (Whipkey ST1, Greene Co., PA) for REEs, TOC, gas-producing potential, trace metal content, and carbon isotopes of organic matter in order to determine the REE systematics of a black shale currently undergoing shale gas development. We also conducted a series of sequential leaching experiments targeting the phosphatic fractions in order to evaluate the dominant host phase of REEs in a black shale. Knowledge of the REE system in the Marcellus black shale will allow us to evaluate potential REE release and behavior during hydraulic fracturing operations. Total REE content of the Whipkey ST1 core ranged from 65-185 μg/g and we observed three distinct REE shale-normalized patterns: middle-REE enrichment (MREE/MREE* ~2) with heavy-REE enrichment (HREE/LREE ~1.8-2), flat patterns, and a linear enrichment towards the heavy-REE (HREE/LREE ~1.5-2.5). The MREE enrichment occurred in the high carbonate samples of the Stafford Member overlying the Marcellus Formation. The HREE enrichment occurred in the Union Springs Member of the Marcellus Formation, corresponding to a high TOC peak (TOC ~4.6-6.2 wt%) and moderate carbonate levels (CaCO3 ~4-53 wt%). Results from the sequential leaching experiments suggest that the dominant host of the REEs is the organic fraction of the black shale and that the detrital and authigenic fractions have characteristic MREE enrichments. We present our

Pre-irradiation testing of experimental fuel elements

International Nuclear Information System (INIS)

Basova, B.G.; Davydov, E.F.; Dvoretskij, V.G.; Ivanov, V.B.; Syuzev, V.N.; Timofeev, G.A.; Tsykanov, V.A.

1979-01-01

The problems of testing of experimental fuel elements of nuclear reactors on the basis of complex accountancy of the factors defining operating capacity of the fuel elements are considered. The classification of the parameters under control and the methods of initial technological testing, including testing of the fuel product, cladding and fished fuel element, is given. The requirements to the apparatus used for complex testing are formulated. One of the possible variants of representation of the information obtained in the form of the input certificate of a single fuel element under study is proposed. The processing flowsheet of the gathered information using the computer is given. The approach under consideration is a methodological basis of investigation of fuel element operating life at the testing stage of the experimental fuel elements

A Study on the Effect of Cohesive Laws on Finite Element Analysis of Crack Propagation Using Cohesive Elements

Energy Technology Data Exchange (ETDEWEB)

Seo, Hyeongseok; Baek, Hyungchan; Kim, Hyungyu [Seoul Nat' l Univ. of Sci. and Tech., Seoul (Korea, Republic of)

2014-04-15

In this paper, the effect of cohesive laws on the finite element analysis of crack propagation using cohesive elements is investigated through three-point bending and double cantilever beam problems. The cohesive elements are implemented into ABAQUS/Standard user subroutines(UEL), and the shape of cohesive law is varied by changing parameters in polynomial functions of cohesive traction-separation relations. In particular, crack propagation behaviors are studied by comparing load-displacement curves of the analysis models which have different shapes of cohesive laws with the same values of fracture energy and cohesive strength. Furthermore, the influence of the element size on crack propagation is discussed in this study.

Trace element metabolism in man and animals

International Nuclear Information System (INIS)

Kirchgessner, M.

1977-01-01

Uptake, distribution, storage, excretion of different trace elements and resulting disturbances are investigated in blood and organs in animal experiments and in human diagnostics with the aid of radioisotopes. Apart from this, untritional disturbances are mentioned. Finally, future aspects of physiological trace element examinations are listed. (AJ) 891 AJ [de

Trace elements in relation to cardiovascular diseases

Energy Technology Data Exchange (ETDEWEB)

Masironi, R [World Health Organization, Cardiovascular Diseases Unit, Geneva (Switzerland); Parr, R M [International Atomic Energy Agency, Medical Applications Section, Vienna (Austria)

1973-07-01

For the past four years the World Health Organization and the International Atomic Energy-Agency have been jointly coordinating investigations at an international level on the role possibly played by stable trace elements in the aetiology of cardiovascular diseases, and the use of nuclear techniques in studying these elements. (author)

Nonlinear finite element modeling of corrugated board

Science.gov (United States)

A. C. Gilchrist; J. C. Suhling; T. J. Urbanik

1999-01-01

In this research, an investigation on the mechanical behavior of corrugated board has been performed using finite element analysis. Numerical finite element models for corrugated board geometries have been created and executed. Both geometric (large deformation) and material nonlinearities were included in the models. The analyses were performed using the commercial...

Institute for transuranium elements Karlsruhe Annual Report 1988

International Nuclear Information System (INIS)

1989-01-01

The present report summarizes the results of the work which has been performed in 1988 at the Institute for Transuranium Elements of the Joint Research Centre of the Commission of the European Communities. While, as in the past, major efforts were devoted to the Programme on Nuclear Fuels and Actinide Research, important contributions were made to other JRC Specific Programmes, i.e. Reactor Safety, Radioactive Waste Management, and Safeguards and Fissile Materials Control. In addition, The Institute has carried out analytical work for the EURATOM Safeguards Directorate and executed research tasks in the safeguards context, both, for the Commission of the European Communities and for the International Atomic Energy Agency in Vienna. Exploratory Research, finally, dealt with an investigation of possibilities of acoustic aerosol scavenging

Investigations on inorganic elements in human lenses of normal and senile cataractous character

International Nuclear Information System (INIS)

Oerdoegh, M.; Racz, P.

1977-01-01

Some essential trace elements as copper, zinc, iron, cobalt, scandium and rubidium have been measured by neutron activation analysis in normal and different types of senile cataractous lenses. Normal lenses were obtained from eyes enucleated because of tumours of the posterior pole and removed from cadaver eyes in 4 hrs after death. The cataractous lenses with intact capsule were removed by cryoextraction and immediately analysed. The single lenses were dried at 100 deg C to constant weight and always weighed before (wet weight) and after drying (dry weight). Unfortunately, because of the nuclear properties of the analysed elements not all of them could be determined in a single lense, thus three lenses were needed for the determination of eight elements. For the determination of manganese a single lens was irradiated for 6 min, then destroyed in a mixture of conc. sulphuric acid and conc. nitric acid. This was followed by a two-step chemical separation. For the analysis of copper the samples were irradiated for 1 hr, then destroyed as above and the copper was separated in the form of copper-thiocyanate. The long-lived isotopes were measured after 115 hrs irradiation and a cooling for 10 days without destruction of the sample. Tabulated data are given and the results are compared with literature data. (T.G.)

Element-resolved x-ray ferrimagnetic and ferromagnetic resonance spectroscopy

International Nuclear Information System (INIS)

Boero, G; Mouaziz, S; Rusponi, S; Bencok, P; Nolting, F; Stepanow, S; Gambardella, P

2008-01-01

We report on the measurement of element-specific magnetic resonance spectra at gigahertz frequencies using x-ray magnetic circular dichroism (XMCD). We investigate the ferrimagnetic precession of Gd and Fe ions in Gd-substituted yttrium iron garnet, showing that the resonant field and linewidth of Gd precisely coincide with Fe up to the nonlinear regime of parametric excitations. The opposite sign of the Gd x-ray magnetic resonance signal with respect to Fe is consistent with dynamic antiferromagnetic alignment of the two ionic species. Further, we investigate a bilayer metal film, Ni 80 Fe 20 (5 nm)/Ni(50 nm), where the coupled resonance modes of Ni and Ni 80 Fe 20 are separately resolved, revealing shifts in the resonance fields of individual layers but no mutual driving effects. Energy-dependent dynamic XMCD measurements are introduced, combining x-ray absorption and magnetic resonance spectroscopies

Investigation of different cage designs and mechano-regulation algorithms in the lumbar interbody fusion process - a finite element analysis.

Science.gov (United States)

Postigo, Sergio; Schmidt, Hendrik; Rohlmann, Antonius; Putzier, Michael; Simón, Antonio; Duda, Georg; Checa, Sara

2014-04-11

Lumbar interbody fusion cages are commonly used to treat painful spinal degeneration and instability by achieving bony fusion. Many different cage designs exist, however the effect of cage morphology and material properties on the fusion process remains largely unknown. This finite element model study aims to investigate the influence of different cage designs on bone fusion using two mechano-regulation algorithms of tissue formation. It could be observed that different cages play a distinct key role in the mechanical conditions within the fusion region and therefore regulate the time course of the fusion process. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigation of Element Effect on High-Temperature Oxidation of HVOF NiCoCrAlX Coatings

Directory of Open Access Journals (Sweden)

Pimin Zhang

2018-04-01

Full Text Available MCrAlX (M: Ni or Co or both, X: minor elements coatings have been used widely to protect hot components in gas turbines against oxidation and heat corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behavior is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y + Ru and Ce, respectively, were deposited on an Inconel-792 substrate using high velocity oxygen fuel (HVOF. The samples were subjected to isothermal oxidation tests in laboratory air at 900, 1000, and 1100 °C and a cyclic oxidation test between 100 and 1100 °C with a 1-h dwell time at 1100 °C. It was observed that the coating with Ce showed a much higher oxidation rate than the coating with Y + Ru under both isothermal and cyclic oxidation tests. In addition, the Y + Ru-doped coating showed significantly lower β phase depletion due to interdiffusion between the coating and the substrate, resulting from the addition of Ru. Simulation results using a moving phase boundary model and an established oxidation-diffusion model showed that Ru stabilized β grains, which reduced β-depletion of the coating due to substrate interdiffusion. This paper, combining experiment and simulation results, presents a comprehensive study of the influence of Ce and Ru on oxidation behavior, including an investigation of the microstructure evolution in the coating surface and the coating-substrate interface influenced by oxidation time.

Nuclide documentation. Element specific parameter values used in the biospheric models of the safety assessments SR 97 and SAFE

International Nuclear Information System (INIS)

Karlsson, Sara; Bergstroem, Ulla

2002-05-01

In this report the element and nuclide specific parameter values used in the biospheric models of the safety assessments SR 97 and SAFE are presented. The references used are presented and where necessary the process of estimation of data is described. The parameters treated in this report are distribution coefficients in soil, organic soil and suspended matter in freshwater and brackish water, root uptake factors for pasturage, cereals, root crops and vegetables, bioaccumulation factors for freshwater fish, brackish water fish, freshwater invertebrates and marine water plants, transfer coefficients for transfer to milk and meat, translocation factors and dose coefficients for external exposure, ingestion (age-dependent values) and inhalation (age-dependent values). The radionuclides treated are those which could be of interest in the two safety assessments. Physical data such as half-lives and type of decay are also presented

Nuclide documentation. Element specific parameter values used in the biospheric models of the safety assessments SR 97 and SAFE

Energy Technology Data Exchange (ETDEWEB)

Karlsson, Sara; Bergstroem, Ulla [Studsvik Eco and Safety AB, Nykoeping (Sweden)

2002-05-01

In this report the element and nuclide specific parameter values used in the biospheric models of the safety assessments SR 97 and SAFE are presented. The references used are presented and where necessary the process of estimation of data is described. The parameters treated in this report are distribution coefficients in soil, organic soil and suspended matter in freshwater and brackish water, root uptake factors for pasturage, cereals, root crops and vegetables, bioaccumulation factors for freshwater fish, brackish water fish, freshwater invertebrates and marine water plants, transfer coefficients for transfer to milk and meat, translocation factors and dose coefficients for external exposure, ingestion (age-dependent values) and inhalation (age-dependent values). The radionuclides treated are those which could be of interest in the two safety assessments. Physical data such as half-lives and type of decay are also presented.

Fuel elements for pressurised-gas reactors; Elements combustibles des piles a gaz sous pression

Energy Technology Data Exchange (ETDEWEB)

Stohr, J A; Englander, M; Gauthron, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

The design and fabrication of fuel elements for the first CO{sub 2} pressurized reactors have induced to investigate: various cladding materials, natural uranium base fuels, canning processes. The main analogical tests used in connection with the fuel element study are described. These various tests have enabled, among others, the fabrication of the fuel element for the EL2 reactor. Lastly, future solutions for electrical power producing reactors are foreseen. (author)Fren. [French] L'etude et la realisation d'elements combustibles pour les premieres piles a CO{sub 2} sous pression ont conduit a examiner: les divers materiaux de gaine, les combustibles a base d'uranium naturel, les modes de gainage. Les principaux essais analogiques ayant servi au cours de l'etude de la cartouche sont decrits. Ces divers essais ont notamment permis la realisation de la cartouche de la pile EL2. Enfin sont envisagees les solutions futures pour les piles productrices d'energie electrique. (auteur)

Investigating ASME allowable loads with finite element analyses

International Nuclear Information System (INIS)

Mattar Neto, Miguel; Bezerra, Luciano M.; Miranda, Carlos A. de J.; Cruz, Julio R.B.

1995-01-01

The evaluation of nuclear components using finite element analysis (FEA) does not generally fall into the shell type verification adopted by the ASME Code. Consequently, the demonstration that the modes of failure are avoided sometimes is not straightforward. Allowable limits, developed by limit load theory, require the computation of shell membrane and bending stresses. How to calculate these stresses from FEA is not necessarily self-evident. One approach to be considered is to develop recommendations in a case-by-case basis for the most common pressure vessel geometries and loads based on comparison between the results of elastic and plastic FEA. In this paper, FE analyses of common 2D and complex 3D geometries are examined and discussed. It will be clear that in the cases studied, stress separation and categorization are not self-evident and simple tasks to undertake. Certain unclear recommendations of ASME Code can lead the stress analyst to non conservative designs as will be demonstrated in this paper. At the endo of this paper, taking into account comparison between elastic and elastic-plastic FE results from ANSYS some observations, suggestions and conclusions about the degree of conservatism of the ASME recommendations will be addressed. (author)

Identification of a functional element in the promoter of the silkworm (Bombyx mori) fat body-specific gene Bmlp3.

Science.gov (United States)

Xu, Hanfu; Deng, Dangjun; Yuan, Lin; Wang, Yuancheng; Wang, Feng; Xia, Qingyou

2014-08-01

30K proteins are a group of structurally related proteins that play important roles in the life cycle of the silkworm Bombyx mori and are largely synthesized and regulated in a time-dependent manner in the fat body. Little is known about the upstream regulatory elements associated with the genes encoding these proteins. In the present study, the promoter of Bmlp3, a fat body-specific gene encoding a 30K protein family member, was characterized by joining sequences containing the Bmlp3 promoter with various amounts of 5' upstream sequences to a luciferase reporter gene. The results indicated that the sequences from -150 to -250bp and -597 to -675bp upstream of the Bmlp3 transcription start site were necessary for high levels of luciferase activity. Further analysis showed that a 21-bp sequence located between -230 and -250 was specifically recognized by nuclear factors from silkworm fat bodies and BmE cells, and could enhance luciferase reporter-gene expression 2.8-fold in BmE cells. This study provides new insights into the Bmlp3 promoter and contributes to the further clarification of the function and developmental regulation of Bmlp3. Copyright © 2014. Published by Elsevier B.V.

Arbuscular mycorrhizal fungi affect glucosinolate and mineral element composition in leaves of Moringa oleifera.

Science.gov (United States)

Cosme, Marco; Franken, Philipp; Mewis, Inga; Baldermann, Susanne; Wurst, Susanne

2014-10-01

Moringa is a mycorrhizal crop cultivated in the tropics and subtropics and appreciated for its nutritive and health-promoting value. As well as improving plant mineral nutrition, arbuscular mycorrhizal fungi (AMF) can affect plant synthesis of compounds bioactive against chronic diseases in humans. Rhizophagus intraradices and Funneliformis mosseae were used in a full factorial experiment to investigate the impact of AMF on the accumulation of glucosinolates, flavonoids, phenolic acids, carotenoids, and mineral elements in moringa leaves. Levels of glucosinolates were enhanced, flavonoids and phenolic acids were not affected, levels of carotenoids (including provitamin A) were species-specifically reduced, and mineral elements were affected differently, with only Cu and Zn being increased by the AMF. This study presents novel results on AMF effects on glucosinolates in leaves and supports conclusions that the impacts of these fungi on microelement concentrations in edible plants are species dependent. The nonspecific positive effects on glucosinolates and the species-specific negative effects on carotenoids encourage research on other AMF species to achieve general benefits on bioactive compounds in moringa.

Bromodomain protein 4 discriminates tissue-specific super-enhancers containing disease-specific susceptibility loci in prostate and breast cancer

DEFF Research Database (Denmark)

Zuber, Verena; Bettella, Francesco; Witoelar, Aree

2017-01-01

progression. Although previous approaches have been tried to explain risk associated with SNPs in regulatory DNA elements, so far epigenetic readers such as bromodomain containing protein 4 (BRD4) and super-enhancers have not been used to annotate SNPs. In prostate cancer (PC), androgen receptor (AR) binding......Background: Epigenetic information can be used to identify clinically relevant genomic variants single nucleotide polymorphisms (SNPs) of functional importance in cancer development. Super-enhancers are cell-specific DNA elements, acting to determine tissue or cell identity and driving tumor...... the differential enrichment of SNPs mapping to specific categories of enhancers. We find that BRD4 is the key discriminant of tissue-specific enhancers, showing that it is more powerful than AR binding information to capture PC specific risk loci, and can be used with similar effect in breast cancer (BC...

Phytostabilization of semiarid soils residually contaminated with trace elements using by-products: Sustainability and risks

Energy Technology Data Exchange (ETDEWEB)

Perez-de-Mora, Alfredo, E-mail: perezdemora@gmail.com [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain); Madejon, Paula; Burgos, Pilar; Cabrera, Francisco [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain); Lepp, Nicholas W. [35, Victoria Road, Formby, Liverpool L37 7DH (United Kingdom); Madejon, Engracia [Instituto de Recursos Naturales y Agrobiologia de Sevilla (IRNAS), CSIC, PO Box 1052, 41080 Sevilla (Spain)

2011-10-15

We investigated the efficiency of various by-products (sugarbeet lime, biosolid compost and leonardite), based on single or repeated applications to field plots, on the establishment of a vegetation cover compatible with a stabilization strategy on a multi-element (As, Cd, Cu, Pb and Zn) contaminated soil 4-6 years after initial amendment applications. Results indicate that the need for re-treatment is amendment- and element-dependent; in some cases, a single application may reduce trace element concentrations in above-ground biomass and enhance the establishment of a healthy vegetation cover. Amendment performance as evaluated by % cover, biomass and number of colonizing taxa differs; however, changes in plant community composition are not necessarily amendment-specific. Although the translocation of trace elements to the plant biotic compartment is greater in re-vegetated areas, overall loss of trace elements due to soil erosion and plant uptake is usually smaller compared to that in bare soil. - Highlights: > By-products enhance vegetation dynamics in contaminated semiarid soils. > Depending on the situation single or repeated incorporations may be required. > The structure of the plant community established is not amendment-dependent. > Phytostabilization reduces overall loss of trace elements in semiarid soils. - Phytostabilization using by-products as amendments is a suitable approach for long-term immobilization of various trace elements in semiarid contaminated soils.

Phytostabilization of semiarid soils residually contaminated with trace elements using by-products: Sustainability and risks

International Nuclear Information System (INIS)

Perez-de-Mora, Alfredo; Madejon, Paula; Burgos, Pilar; Cabrera, Francisco; Lepp, Nicholas W.; Madejon, Engracia

2011-01-01

We investigated the efficiency of various by-products (sugarbeet lime, biosolid compost and leonardite), based on single or repeated applications to field plots, on the establishment of a vegetation cover compatible with a stabilization strategy on a multi-element (As, Cd, Cu, Pb and Zn) contaminated soil 4-6 years after initial amendment applications. Results indicate that the need for re-treatment is amendment- and element-dependent; in some cases, a single application may reduce trace element concentrations in above-ground biomass and enhance the establishment of a healthy vegetation cover. Amendment performance as evaluated by % cover, biomass and number of colonizing taxa differs; however, changes in plant community composition are not necessarily amendment-specific. Although the translocation of trace elements to the plant biotic compartment is greater in re-vegetated areas, overall loss of trace elements due to soil erosion and plant uptake is usually smaller compared to that in bare soil. - Highlights: → By-products enhance vegetation dynamics in contaminated semiarid soils. → Depending on the situation single or repeated incorporations may be required. → The structure of the plant community established is not amendment-dependent. → Phytostabilization reduces overall loss of trace elements in semiarid soils. - Phytostabilization using by-products as amendments is a suitable approach for long-term immobilization of various trace elements in semiarid contaminated soils.

Distribution of trace elements in Western Canadian coal ashes

Energy Technology Data Exchange (ETDEWEB)

Kronberg, B I; Brown, J R; Fyfe, W S; Peirce, M; Winder, C G

1981-01-01

Concentrations of 52 minor elements in coal ash were determined using spark source mass spectroscopy. Hg levels in raw coal were investigated by cold vapour atomic absorption spectrophotometry. The concentration of elements are compared to other available data and to levels in the Earth's crust. F levels in coal ash exceed 500/sub g-1/ and may be greater than 1 wt% om raw coal. Approximately half the elements (B, S, Ni, Zn, Ga, Se, Sr, Y, Mo, Sn, Sb, I, Ba, Pr, Nd, Sm, Eu, Ho, Hf, Pt, Hg, Pb, Tl, Bi, U) investigated are enriched in the coal ash with respect to the Earth's crust. The ranges in minor element concentrations in coal ash and coal from different global regions are very similar.

The Effects of Computer Graphic Organizers on the Persuasive Writing of Hispanic Middle School Students with Specific Learning Disabilities

Science.gov (United States)

Unzueta, Caridad H.; Barbetta, Patricia M.

2012-01-01

A multiple baseline design investigated the effects of computer graphic organizers on the persuasive composition writing skills of four Hispanic students with specific learning disabilities. Participants reviewed the elements of persuasive writing and then developed compositions using a word processing program. Baseline planning was done with a…

Transcription factor trapping by RNA in gene regulatory elements.

Science.gov (United States)

Sigova, Alla A; Abraham, Brian J; Ji, Xiong; Molinie, Benoit; Hannett, Nancy M; Guo, Yang Eric; Jangi, Mohini; Giallourakis, Cosmas C; Sharp, Phillip A; Young, Richard A

2015-11-20

Transcription factors (TFs) bind specific sequences in promoter-proximal and -distal DNA elements to regulate gene transcription. RNA is transcribed from both of these DNA elements, and some DNA binding TFs bind RNA. Hence, RNA transcribed from regulatory elements may contribute to stable TF occupancy at these sites. We show that the ubiquitously expressed TF Yin-Yang 1 (YY1) binds to both gene regulatory elements and their associated RNA species across the entire genome. Reduced transcription of regulatory elements diminishes YY1 occupancy, whereas artificial tethering of RNA enhances YY1 occupancy at these elements. We propose that RNA makes a modest but important contribution to the maintenance of certain TFs at gene regulatory elements and suggest that transcription of regulatory elements produces a positive-feedback loop that contributes to the stability of gene expression programs. Copyright © 2015, American Association for the Advancement of Science.

Gene conversion as a secondary mechanism of short interspersed element (SINE) evolution

Energy Technology Data Exchange (ETDEWEB)

Kass, D.H. [Louisiana State Univ. Medical Center, New Orleans, LA (United States). Dept. of Biochemistry and Molecular Biology; Batzer, M.A. [Lawrence Livermore National Lab., CA (United States); Deininger, P.L. [Louisiana State Univ. Medical Center, New Orleans, LA (United States). Dept. of Biochemistry and Molecular Biology]|[Alton Ochsner Medical Foundation, New Orleans, LA (United States). Lab. of Molecular Genetics

1995-01-01

The Alu repetitive family of short interspersed elements (SINEs) in primates can be subdivided into distinct subfamilies by specific diagnostic nucleotide changes. The older subfamilies are generally very abundant, while the younger subfamilies have fewer copies. Some of the youngest Alu elements are absent in the orthologous loci of nonhuman primates, indicative of recent retroposition events, the primary mode of SINE evolutions. PCR analysis of one young Alu subfamily (Sb2) member found in the low-density lipoprotein receptor gene apparently revealed the presence of this element in the green monkey, orangutan, gorilla, and chimpanzee genomes, as well as the human genome. However, sequence analysis of these genomes revealed a highly mutated, older, primate-specific Alu element was present at this position in the nonhuman primates. Comparison of the flanking DNA sequences upstream of this Alu insertion corresponded to evolution expected for standard primate phylogeny, but comparison of the Alu repeat sequences revealed that the human element departed from this phylogeny. The change in the human sequence apparently occurred by a gene conversion event only within the Alu element itself, converting it from one of the oldest to one of the youngest Alu subfamilies. Although gene conversions of Alu elements are clearly very rare, this finding shows that such events can occur and contribute to specific cases of SINE subfamily evolution.

In silico discovery of transcription regulatory elements in Plasmodium falciparum

Directory of Open Access Journals (Sweden)

Le Roch Karine G

2008-02-01

Full Text Available Abstract Background With the sequence of the Plasmodium falciparum genome and several global mRNA and protein life cycle expression profiling projects now completed, elucidating the underlying networks of transcriptional control important for the progression of the parasite life cycle is highly pertinent to the development of new anti-malarials. To date, relatively little is known regarding the specific mechanisms the parasite employs to regulate gene expression at the mRNA level, with studies of the P. falciparum genome sequence having revealed few cis-regulatory elements and associated transcription factors. Although it is possible the parasite may evoke mechanisms of transcriptional control drastically different from those used by other eukaryotic organisms, the extreme AT-rich nature of P. falciparum intergenic regions (~90% AT presents significant challenges to in silico cis-regulatory element discovery. Results We have developed an algorithm called Gene Enrichment Motif Searching (GEMS that uses a hypergeometric-based scoring function and a position-weight matrix optimization routine to identify with high-confidence regulatory elements in the nucleotide-biased and repeat sequence-rich P. falciparum genome. When applied to promoter regions of genes contained within 21 co-expression gene clusters generated from P. falciparum life cycle microarray data using the semi-supervised clustering algorithm Ontology-based Pattern Identification, GEMS identified 34 putative cis-regulatory elements associated with a variety of parasite processes including sexual development, cell invasion, antigenic variation and protein biosynthesis. Among these candidates were novel motifs, as well as many of the elements for which biological experimental evidence already exists in the Plasmodium literature. To provide evidence for the biological relevance of a cell invasion-related element predicted by GEMS, reporter gene and electrophoretic mobility shift assays

SXT/R391 Integrative and Conjugative Elements (ICEs) Encode a Novel 'Trap-Door' Strategy for Mobile Element Escape.

Science.gov (United States)

Ryan, Michael P; Armshaw, Patricia; Pembroke, J Tony

2016-01-01

Integrative conjugative elements (ICEs) are a class of bacterial mobile elements that have the ability to mediate their own integration, excision, and transfer from one host genome to another by a mechanism of site-specific recombination, self-circularisation, and conjugative transfer. Members of the SXT/R391 ICE family of enterobacterial mobile genetic elements display an unusual UV-inducible sensitization function which results in stress induced killing of bacterial cells harboring the ICE. This sensitization has been shown to be associated with a stress induced overexpression of a mobile element encoded conjugative transfer gene, orf43, a traV homolog. This results in cell lysis and release of a circular form of the ICE. Induction of this novel system may allow transfer of an ICE, enhancing its survival potential under conditions not conducive to conjugative transfer.

Levels of major and trace elements, including rare earth elements, and ²³⁸U in Croatian tap waters.

Science.gov (United States)

Fiket, Željka; Rožmarić, Martina; Krmpotić, Matea; Benedik, Ljudmila

2015-05-01

Concentrations of 46 elements, including major, trace, and rare earth elements, and (238)U in Croatian tap waters were investigated. Selected sampling locations include tap waters from various hydrogeological regions, i.e., different types of aquifers, providing insight into the range of concentrations of studied elements and (238)U activity concentrations in Croatian tap waters. Obtained concentrations were compared with the Croatian maximum contaminant levels for trace elements in water intended for human consumption, as well as WHO and EPA drinking water standards. Concentrations in all analyzed tap waters were found in accordance with Croatian regulations, except tap water from Šibenik in which manganese in concentration above maximum permissible concentration (MPC) was measured. Furthermore, in tap water from Osijek, levels of arsenic exceeded the WHO guidelines and EPA regulations. In general, investigated tap waters were found to vary considerably in concentrations of studied elements, including (238)U activity concentrations. Causes of variability were further explored using statistical methods. Composition of studied tap waters was found to be predominately influenced by hydrogeological characteristics of the aquifer, at regional and local level, the existing redox conditions, and the household plumbing system. Rare earth element data, including abundances and fractionation patterns, complemented the characterization and facilitated the interpretation of factors affecting the composition of the analyzed tap waters.

Electrical engineering design using characterized elements; Conception en genie electrique a l'aide d'elements caracterises

Energy Technology Data Exchange (ETDEWEB)

Demni, H.E.

2004-10-15

This work treats systematic design of energy transformation structures used in Electrical Engineering. We propose an approach dedicated to design by association of characterized elements. Starting from a set of specifications, the designer has to define a coherent structure by assembling predefined elements. Within this framework, we adopt a characterization approach that takes into account various criteria necessary for design. Then, this approach allowed us to develop methodologies for designing electric energy transformation structures. These methodologies were used to implement a software application based on three tools: a data base as an elements library, a graphic tool allowing the construction of energy transformation structures, an expert module which helps the designer in his work. (author)

The dynamic efficiency of feed-in tariffs: The impact of different design elements

International Nuclear Information System (INIS)

Río, Pablo del

2012-01-01

Dynamic efficiency has received much less attention than the effectiveness and static efficiency criteria to assess policies to support electricity from renewable energy sources (RES-E). On the other hand, the literature on RES-E support shows that the choice of design elements within RES-E support instruments is at least as important to successfully promote RES-E as the choice of specific instruments. The aim of this paper is to build a theoretical framework for dynamic efficiency analysis and assess the dynamic efficiency properties of the different design elements of feed-in tariffs. It is shown that, in fact, several design elements can have a significant impact on the different dimensions of dynamic efficiency. Particularly relevant design elements in this context are technology-specific fixed-tariffs, floor prices, degression, reductions of support over time for existing plants, long duration of support and support falling on consumers. In addition, it is shown than some design elements would be more appropriate than others to activate specific dimensions. - Highlights: ► A theoretical framework for dynamic efficiency analysis is built. ► The dynamic efficiency properties of feed-in tariffs design elements are assessed. ► Several design elements have a significant impact on the different dimensions of dynamic efficiency.