WorldWideScience

Sample records for electrospun nanofiber meshes

  1. Chondroitin sulfate immobilization at the surface of electrospun nanofiber meshes for cartilage tissue regeneration approaches

    Energy Technology Data Exchange (ETDEWEB)

    Piai, Juliana Francis [3B’s Research Group − Biomaterials, Biodegradables and Biomimetics, Department of Polymer Engineering, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4805-017 Barco, Guimarães (Portugal); ICVS/3B’s − PT Government Associate Laboratory, Braga/Guimarães (Portugal); Grupo de Materiais Poliméricos e Compósitos, GMPC – Departamento de Química- Universidade Estadual de Maringá, Av. Colombo 5790, 87020-900, Maringá, Paraná (Brazil); Alves da Silva, Marta; Martins, Albino; Torres, Ana Bela [3B’s Research Group − Biomaterials, Biodegradables and Biomimetics, Department of Polymer Engineering, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4805-017 Barco, Guimarães (Portugal); ICVS/3B’s − PT Government Associate Laboratory, Braga/Guimarães (Portugal); Faria, Susana [Research Center Officinal Mathematical, Department of Mathematics for Science and Technology, University of Minho, Campus de Azurém, 4800-058 Guimarães (Portugal); and others

    2017-05-01

    Highlights: • Chemical immobilization of chondroitin sulfate at the surface of nanofiber meshes. • CS-immobilized NFMs showed lower roughness and higher hydrophilicity. • CS-immobilized NFMs offer a highly effective substrate for hACs phenotypic stability. - Abstract: Aiming at improving the biocompatibility of biomaterial scaffolds, surface modification presents a way to preserve their mechanical properties and to improve the surface bioactivity. In this work, chondroitin sulfate (CS) was immobilized at the surface of electrospun poly(caprolactone) nanofiber meshes (PCL NFMs), previously functionalized by UV/O{sub 3} exposure and aminolysis. Contact angle, SEM, optical profilometry, FTIR, X-ray photoelectron spectroscopy techniques confirmed the success of CS-immobilization in PCL NFMs. Furthermore, CS-immobilized PCL NFMs showed lower roughness and higher hydrophilicity than the samples without CS. Human articular chondrocytes (hACs) were cultured on electrospun PCL NFMs with or without CS immobilization. It was observed that hACs proliferated through the entire time course of the experiment in both types of nanofibrous scaffolds, as well as for the production of glycosaminoglycans. Quantitative-PCR results demonstrated over-expression of cartilage-related genes such as Aggrecan, Collagen type II, COMP and Sox9 on both types of nanofibrous scaffolds. Morphological observations from SEM and LSCM revealed that hACs maintained their characteristic round shape and cellular agglomeration exclusively on PCL NFMs with CS immobilization. In conclusion, CS immobilization at the surface of PCL NFMs was achieved successfully and provides a valid platform enabling further surface functionalization methods in scaffolds to be developed for cartilage tissue engineering.

  2. Chondroitin sulfate immobilization at the surface of electrospun nanofiber meshes for cartilage tissue regeneration approaches

    Science.gov (United States)

    Piai, Juliana Francis; da Silva, Marta Alves; Martins, Albino; Torres, Ana Bela; Faria, Susana; Reis, Rui L.; Muniz, Edvani Curti; Neves, Nuno M.

    2017-05-01

    Aiming at improving the biocompatibility of biomaterial scaffolds, surface modification presents a way to preserve their mechanical properties and to improve the surface bioactivity. In this work, chondroitin sulfate (CS) was immobilized at the surface of electrospun poly(caprolactone) nanofiber meshes (PCL NFMs), previously functionalized by UV/O3 exposure and aminolysis. Contact angle, SEM, optical profilometry, FTIR, X-ray photoelectron spectroscopy techniques confirmed the success of CS-immobilization in PCL NFMs. Furthermore, CS-immobilized PCL NFMs showed lower roughness and higher hydrophilicity than the samples without CS. Human articular chondrocytes (hACs) were cultured on electrospun PCL NFMs with or without CS immobilization. It was observed that hACs proliferated through the entire time course of the experiment in both types of nanofibrous scaffolds, as well as for the production of glycosaminoglycans. Quantitative-PCR results demonstrated over-expression of cartilage-related genes such as Aggrecan, Collagen type II, COMP and Sox9 on both types of nanofibrous scaffolds. Morphological observations from SEM and LSCM revealed that hACs maintained their characteristic round shape and cellular agglomeration exclusively on PCL NFMs with CS immobilization. In conclusion, CS immobilization at the surface of PCL NFMs was achieved successfully and provides a valid platform enabling further surface functionalization methods in scaffolds to be developed for cartilage tissue engineering.

  3. Electrospun Nanofibers Applications in Dentistry

    Directory of Open Access Journals (Sweden)

    Seog-Jin Seo

    2016-01-01

    Full Text Available Nanofibrous structures exhibit many interesting features, such as high surface area and surface functionalization and porosity in the range from submicron to nanoscale, which mimics the natural extracellular matrix. In particular, electrospun nanofibers have gained great attention in the field of tissue engineering due to the ease of fabrication and tailorability in pore size, scaffold shape, and fiber alignment. For the reasons, recently, polymeric nanofibers or bioceramic nanoparticle-incorporated nanofibers have been used in dentistry, and their nanostructure and flexibility have contributed to highly promotive cell homing behaviors, resulting in expecting improved dental regeneration. Here, this paper focuses on recently applied electrospun nanofibers in dentistry in the range from the process to the applications.

  4. Enzyme-carrying electrospun nanofibers.

    Science.gov (United States)

    Jia, Hongfei

    2011-01-01

    Compared to other nanomaterials as supports for enzyme immobilization, nanofibers provide a promising configuration in balancing the key factors governing the catalytic performance of the immobilized enzymes including surface area-to-volume ratio, mass transfer resistance, effective loading, and the easiness to recycle. Synthetic and natural polymers can be fabricated into nanofibers via a physical process called electrospinning. The process requires only simple apparatus to operate, yet has proved to be very flexible in the selection of feedstock materials and also effective to control and manipulate the properties of the resulting nanofibers such as size and surface morphology, which are typically important parameters for enzyme immobilization supports. This chapter describes a protocol for the preparation of nanofibrous enzyme, involving the synthesis and end-group functionalization of polystyrene, production of electrospun nanofibers, and surface immobilization of enzyme via covalent attachment.

  5. Biomimetic electrospun nanofibers for tissue regeneration

    International Nuclear Information System (INIS)

    Liao, Susan; Li Bojun; Ma Zuwei; Wei He; Chan Casey; Ramakrishna, Seeram

    2006-01-01

    Nanofibers exist widely in human tissue with different patterns. Electrospinning nanotechnology has recently gained a new impetus due to the introduction of the concept of biomimetic nanofibers for tissue regeneration. The advanced electrospinning technique is a promising method to fabricate a controllable continuous nanofiber scaffold similar to the natural extracellular matrix. Thus, the biomedical field has become a significant possible application field of electrospun fibers. Although electrospinning has developed rapidly over the past few years, electrospun nanofibers are still at a premature research stage. Further comprehensive and deep studies on electrospun nanofibers are essential for promoting their biomedical applications. Current electrospun fiber materials include natural polymers, synthetic polymers and inorganic substances. This review briefly describes several typically electrospun nanofiber materials or composites that have great potential for tissue regeneration, and describes their fabrication, advantages, drawbacks and future prospects. (topical review)

  6. Electrospun Gallium Nitride Nanofibers

    International Nuclear Information System (INIS)

    Melendez, Anamaris; Morales, Kristle; Ramos, Idalia; Campo, Eva; Santiago, Jorge J.

    2009-01-01

    The high thermal conductivity and wide bandgap of gallium nitride (GaN) are desirable characteristics in optoelectronics and sensing applications. In comparison to thin films and powders, in the nanofiber morphology the sensitivity of GaN is expected to increase as the exposed area (proportional to the length) increases. In this work we present electrospinning as a novel technique in the fabrication of GaN nanofibers. Electrospinning, invented in the 1930s, is a simple, inexpensive, and rapid technique to produce microscopically long ultrafine fibers. GaN nanofibers are produced using gallium nitrate and dimethyl-acetamide as precursors. After electrospinning, thermal decomposition under an inert atmosphere is used to pyrolyze the polymer. To complete the preparation, the nanofibers are sintered in a tube furnace under a NH 3 flow. Both scanning electron microscopy and profilometry show that the process produces continuous and uniform fibers with diameters ranging from 20 to a few hundred nanometers, and lengths of up to a few centimeters. X-ray diffraction (XRD) analysis shows the development of GaN nanofibers with hexagonal wurtzite structure. Future work includes additional characterization using transmission electron microscopy and XRD to understand the role of precursors and nitridation in nanofiber synthesis, and the use of single nanofibers for the construction of optical and gas sensing devices.

  7. Electrospun MOF nanofibers as hydrogen storage media

    CSIR Research Space (South Africa)

    Ren, Jianwei

    2015-06-01

    Full Text Available In this study, Zr-MOF and Cr-MOF were chosen as representatives of the developed MOFs in our laboratory and were incorporated into electrospun nanofibers. The obtained MOF nanofibers composites were evaluated as hydrogen storage media. The results...

  8. Electrospun nanofibers for neural tissue engineering

    Science.gov (United States)

    Xie, Jingwei; MacEwan, Matthew R.; Schwartz, Andrea G.; Xia, Younan

    2010-01-01

    Biodegradable nanofibers produced by electrospinning represent a new class of promising scaffolds to support nerve regeneration. We begin with a brief discussion on the electrospinning of nanofibers and methods for controlling the structure, porosity, and alignment of the electrospun nanofibers. The methods include control of the nanoscale morphology and microscale alignment of the nanofibers, as well as the fabrication of macroscale, three-dimensional tubular structures. We then highlight recent studies that utilize electrospun nanofibers to manipulate biological processes relevant to nervous tissue regeneration, including stem cell differentiation, guidance of neurite extension, and peripheral nerve injury treatments. The main objective of this feature article is to provide valuable insights into methods for investigating the mechanisms of neurite growth on novel nanofibrous scaffolds and optimization of the nanofiber scaffolds and conduits for repairing peripheral nerve injuries.

  9. Electrospun nanofiber scaffolds: engineering soft tissues

    International Nuclear Information System (INIS)

    Kumbar, S G; Nukavarapu, S P; Laurencin, C T; James, R

    2008-01-01

    Electrospinning has emerged to be a simple, elegant and scalable technique to fabricate polymeric nanofibers. Pure polymers as well as blends and composites of both natural and synthetics have been successfully electrospun into nanofiber matrices. Physiochemical properties of nanofiber matrices can be controlled by manipulating electrospinning parameters to meet the requirements of a specific application. Such efforts include the fabrication of fiber matrices containing nanofibers, microfibers, combination of nano-microfibers and also different fiber orientation/alignments. Polymeric nanofiber matrices have been extensively investigated for diversified uses such as filtration, barrier fabrics, wipes, personal care, biomedical and pharmaceutical applications. Recently electrospun nanofiber matrices have gained a lot of attention, and are being explored as scaffolds in tissue engineering due to their properties that can modulate cellular behavior. Electrospun nanofiber matrices show morphological similarities to the natural extra-cellular matrix (ECM), characterized by ultrafine continuous fibers, high surface-to-volume ratio, high porosity and variable pore-size distribution. Efforts have been made to modify nanofiber surfaces with several bioactive molecules to provide cells with the necessary chemical cues and a more in vivo like environment. The current paper provides an overlook on such efforts in designing nanofiber matrices as scaffolds in the regeneration of various soft tissues including skin, blood vessel, tendon/ligament, cardiac patch, nerve and skeletal muscle

  10. Electrospun Nanofibers: New Concepts, Materials, and Applications.

    Science.gov (United States)

    Xue, Jiajia; Xie, Jingwei; Liu, Wenying; Xia, Younan

    2017-08-15

    Electrospinning is a simple and versatile technique that relies on the electrostatic repulsion between surface charges to continuously draw nanofibers from a viscoelastic fluid. It has been applied to successfully produce nanofibers, with diameters down to tens of nanometers, from a rich variety of materials, including polymers, ceramics, small molecules, and their combinations. In addition to solid nanofibers with a smooth surface, electrospinning has also been adapted to generate nanofibers with a number of secondary structures, including those characterized by a porous, hollow, or core-sheath structure. The surface and/or interior of such nanofibers can be further functionalized with molecular species or nanoparticles during or after an electrospinning process. In addition, electrospun nanofibers can be assembled into ordered arrays or hierarchical structures by manipulation of their alignment, stacking, and/or folding. All of these attributes make electrospun nanofibers well-suited for a broad spectrum of applications, including those related to air filtration, water purification, heterogeneous catalysis, environmental protection, smart textiles, surface coating, energy harvesting/conversion/storage, encapsulation of bioactive species, drug delivery, tissue engineering, and regenerative medicine. Over the past 15 years, our group has extensively explored the use of electrospun nanofibers for a range of applications. Here we mainly focus on two examples: (i) use of ceramic nanofibers as catalytic supports for noble-metal nanoparticles and (ii) exploration of polymeric nanofibers as scaffolding materials for tissue regeneration. Because of their high porosity, high surface area to volume ratio, well-controlled composition, and good thermal stability, nonwoven membranes made of ceramic nanofibers are terrific supports for catalysts based on noble-metal nanoparticles. We have investigated the use of ceramic nanofibers made of various oxides, including SiO 2 , TiO 2

  11. Electrospun chitosan/PEDOT nanofibers.

    Science.gov (United States)

    Kiristi, Melek; Oksuz, Aysegul Uygun; Oksuz, Lutfi; Ulusoy, Seyhan

    2013-10-01

    Plasma-modified chitosan and poly(3,4-ethylenedioxythiophene) were blended to obtain conducting nanofibers with polyvinyl alcohol as a supporting polymer at various volumetric ratios by electrospinning method. Chemical compositions and molecular interactions among nanofiber blend components were determined using Fourier transform infrared spectroscopy (FTIR). The conducting blends containing plasma-modified chitosan resulted in a superior antibacterial activity and thinner fiber formation than those containing chitosan without plasma-modification. The obtained nanofiber diameters of plasma-modified chitosan were in the range of 170 to 200 nm and those obtained from unmodified chitosan were in the range of 190 to 246 nm. The electrical and electrochemical properties of nanofibers were also investigated by four-point probe conductivity and cyclic voltammetry measurements. Copyright © 2013 Elsevier B.V. All rights reserved.

  12. Electrospun polyvinyl alcohol–collagen–hydroxyapatite nanofibers: a biomimetic extracellular matrix for osteoblastic cells

    International Nuclear Information System (INIS)

    Song Wei; Shi Tong; Ren Weiping; Markel, David C; Wang Sunxi; Mao Guangzhao

    2012-01-01

    The failure of prosthesis after total joint replacement is due to the lack of early implant osseointegration. In this study polyvinyl alcohol–collagen–hydroxyapatite (PVA-Col-HA) electrospun nanofibrous meshes were fabricated as a biomimetic bone-like extracellular matrix for the modification of orthopedic prosthetic surfaces. In order to reinforce the PVA nanofibers, HA nanorods and Type I collagen were incorporated into the nanofibers. We investigated the morphology, biodegradability, mechanical properties and biocompatibility of the prepared nanofibers. Our results showed these inorganic–organic blended nanofibers to be degradable in vitro. The encapsulated nano-HA and collagen interacted with the PVA content, reinforcing the hydrolytic resistance and mechanical properties of nanofibers that provided longer lasting stability. The encapsulated nano-HA and collagen also enhanced the adhesion and proliferation of murine bone cells (MC3T3) in vitro. We propose the PVA-Col-HA nanofibers might be promising modifying materials on implant surfaces for orthopedic applications. (paper)

  13. Electrospun Nanofibers: Solving Global Issues

    Science.gov (United States)

    Si, Yang; Tang, Xiaomin; Yu, Jianyong; Ding, Bin

    Energy and environment will head the list of top global issues facing society for the next 50 years. Nanotechnology is responding to these challenges by designing and fabricating functional nanofibers optimized for energy and environmental applications. The route toward these nano-objects is based primarily on electrospinning: a highly versatile method that allows the fabrication of continuous fibers with diameters down to a few nanometers. The mechanism responsible for the fiber formation mainly includes the Taylor Cone theory and flight-instability theory, which can be predicted theoretically and controlled experimentally. Moreover, the electrospinning has been applied to natural polymers, synthetic polymers, ceramics, and carbon. Fibers with complex architectures, such as ribbon fiber, porous fiber, core-shell fiber, or hollow fiber, can be produced by special electrospinning methods. It is also possible to produce nanofibrous membranes with designed aggregate structure including alignment, patterning, and two-dimensional nanonets. Finally, the brief analysis of nanofibers used for advanced energy and environmental applications in the past decade indicates that their impact has been realized well and is encouraging, and will continually represent a key technology to ensure sustainable energy and preserve our environment for the future.

  14. Performance Enhancement of Dental Composites Using Electrospun Nanofibers

    OpenAIRE

    H. Dodiuk-Kenig; K. Lizenboim; S. Roth; B. Zalsman; W. A. McHale; M. Jaffe; K. Griswold

    2008-01-01

    The objective of the present study is to investigate the effect of electrospun nanofiber reinforcement on the properties of commercially available, hyperbranched polymer modified (Hybrane, 0.3 wt.% DSM) dental formulations. The emergence of functionalized nanoscale reinforcements having large surface area (hundreds of square meters/gram) has enabled the design of novel nanocomposites with new and complex structures leading to enhanced mechanical and physical properties. Electrospun nanofibers...

  15. Hybrid electrospun chitosan-phospholipids nanofibers for transdermal drug delivery

    DEFF Research Database (Denmark)

    Mendes, Ana Carina Loureiro; Gorzelanny, Christian; Halter, Natalia

    2016-01-01

    Chitosan (Ch) polysaccharide was mixed with phospholipids (P) to generate electrospun hybrid nanofibers intended to be used as platforms for transdermal drug delivery. Ch/P nanofibers exibithed average diameters ranging from 248 +/- 94 nm to 600 +/- 201 nm, depending on the amount of phospholipid...... culture plate (control). The release of curcumin, diclofenac and vitamin B12, as model drugs, from Ch/P hybrid nanofibers was investigated, demonstrating their potential utilization as a transdermal drug delivery system....

  16. A review on electrospun nanofibers for oral drug delivery

    Directory of Open Access Journals (Sweden)

    Abbas Akhgari

    2017-10-01

    Full Text Available Nowadays, polymer nanofibers have gained attention due to remarkable characteristics such as high porosity and large surface area to volume ratio. Among their fabrication methods, electrospinning technique has been attracted as a simple and reproducible approach. It is a versatile, simple and cost-effective technique for the production of continuous nanofibers with acceptable characteristics such as high porosity, high surface area to volume ratio, high loading capacity and encapsulation efficiency, delivery of multiple drugs, and enhancement of drug solubility. Due to these properties electrospun nanofibers have been extensively used for different biomedical applications including wound dressing, tissue engineering, enzyme immobilization, artificial organs, and drug delivery. Different synthetic and natural polymers have been successfully electrospun into ultrafine fibers. Using electrospun nanofibers as vehicles for oral drug delivery has been investigated in different release manners- fast, biphasic or sustained release. This article presents a review on application of electrospinning technique in oral drug delivery.

  17. Wetting Hierarchy in Oleophobic 3D Electrospun Nanofiber Networks.

    Science.gov (United States)

    Stachewicz, Urszula; Bailey, Russell J; Zhang, Hao; Stone, Corinne A; Willis, Colin R; Barber, Asa H

    2015-08-05

    Wetting behavior between electrospun nanofibrous networks and liquids is of critical importance in many applications including filtration and liquid-repellent textiles. The relationship between intrinsic nanofiber properties, including surface characteristics, and extrinsic nanofibrous network organization on resultant wetting characteristics of the nanofiber network is shown in this work. Novel 3D imaging exploiting focused ion beam (FIB) microscopy and cryo-scanning electron microscopy (cryo-SEM) highlights a wetting hierarchy that defines liquid interactions with the network. Specifically, small length scale partial wetting between individual electrospun nanofibers and low surface tension liquids, measured both using direct SEM visualization and a nano Wilhelmy balance approach, provides oleophobic surfaces due to the high porosity of electrospun nanofiber networks. These observations conform to a metastable Cassie-Baxter regime and are important in defining general rules for understanding the wetting behavior between fibrous solids and low surface tension liquids for omniphobic functionality.

  18. Electrospun Ceramic Nanofiber Mats Today: Synthesis, Properties, and Applications

    Science.gov (United States)

    Esfahani, Hamid; Ramakrishna, Seeram

    2017-01-01

    Ceramic nanofibers (NFs) have recently been developed for advanced applications due to their unique properties. In this article, we review developments in electrospun ceramic NFs with regard to their fabrication process, properties, and applications. We find that surface activity of electrospun ceramic NFs is improved by post pyrolysis, hydrothermal, and carbothermal processes. Also, when combined with another surface modification methods, electrospun ceramic NFs result in the advancement of properties and widening of the application domains. With the decrease in diameter and length of a fiber, many properties of fibrous materials are modified; characteristics of such ceramic NFs are different from their wide and long (bulk) counterparts. In this article, electrospun ceramic NFs are reviewed with an emphasis on their applications as catalysts, membranes, sensors, biomaterials, fuel cells, batteries, supercapacitors, energy harvesting systems, electric and magnetic parts, conductive wires, and wearable electronic textiles. Furthermore, properties of ceramic nanofibers, which enable the above applications, and techniques to characterize them are briefly outlined. PMID:29077074

  19. Electrospun Ceramic Nanofiber Mats Today: Synthesis, Properties, and Applications

    Directory of Open Access Journals (Sweden)

    Hamid Esfahani

    2017-10-01

    Full Text Available Ceramic nanofibers (NFs have recently been developed for advanced applications due to their unique properties. In this article, we review developments in electrospun ceramic NFs with regard to their fabrication process, properties, and applications. We find that surface activity of electrospun ceramic NFs is improved by post pyrolysis, hydrothermal, and carbothermal processes. Also, when combined with another surface modification methods, electrospun ceramic NFs result in the advancement of properties and widening of the application domains. With the decrease in diameter and length of a fiber, many properties of fibrous materials are modified; characteristics of such ceramic NFs are different from their wide and long (bulk counterparts. In this article, electrospun ceramic NFs are reviewed with an emphasis on their applications as catalysts, membranes, sensors, biomaterials, fuel cells, batteries, supercapacitors, energy harvesting systems, electric and magnetic parts, conductive wires, and wearable electronic textiles. Furthermore, properties of ceramic nanofibers, which enable the above applications, and techniques to characterize them are briefly outlined.

  20. Electrospun nanofiber membranes for electrically activated shape memory nanocomposites

    Science.gov (United States)

    Zhang, Fenghua; Zhang, Zhichun; Liu, Yanju; Leng, Jinsong

    2014-06-01

    A novel shape memory nanocomposite system, consisting of a thermoplastic Nafion polymer and ultrathin electrospun polyacrylonitrile (PAN)-based carbonization nanofiber membranes, is successfully synthesized. PAN-based carbonization nanofiber networks that offer responses to deformations are considered to be an excellent actuation source. Significant improvement in the electrical conductivity of carbon nanofiber membranes is found by adjusting the applied voltage power in the electrospinning PAN process varying from 7.85 to 12.30 S cm-1. The porous structure of the carbon nanofiber membranes provides a large specific surface area and interfacial contact area when combined with the polymer matrix. Shape memory Nafion nanocomposites filled with interpenetrating non-woven electrospun PAN carbonization membranes can be actuated by applying 14 V electrical voltage within 5 s. The results, as demonstrated through morphology, electrical and thermal measurements and a shape recovery test, suggest a valuable route to producing soft nanocomposites.

  1. Electrospun nanofibers: New generation materials for advanced applications

    International Nuclear Information System (INIS)

    Thenmozhi, S.; Dharmaraj, N.; Kadirvelu, K.; Kim, Hak Yong

    2017-01-01

    Highlights: • A review covering important aspects of electrospinning technique is presented. • Applications of nanofibers in various fields are reviewed. • Possibility to up-scale electrospinning technique to industry also included. - Abstract: Electrospinning (E-spin) is a unique technique to fabricate polymeric as well as metal oxide nanofibers. Research on electrospun nanofibers is a very active field in material science owing to their novel applications in diverse domains. The main focus of this review is to provide an insight into E-spin technique by understanding the working principle, influencing parameters and applications of nanofibers in different walks of life. Several hundreds of papers are published on the preparation, modification and applications of nanofibers produced by E-spin technique in the areas like sensor development, decontamination, energy storage, biomedical and catalysis etc. Details on the industrial scale development of E-spin technique, current scenario and future developments are also covered in this review.

  2. Study on the Electrospun CNTs/Polyacrylonitrile-Based Nanofiber Composites

    Directory of Open Access Journals (Sweden)

    Bo Qiao

    2011-01-01

    Full Text Available CNTs/PAN nanofibers were electrospun from PAN-based solution for the preparation of carbon nanofiber composites. The as-spun polyacrylonitrile-based nanofibers were hot-stretched by weighing metal in a temperature controlled oven. Scanning electron microscopy (SEM and transmission electron microscopy (TEM were used to characterize the morphology of the nanofibers, which indicated that carbon nanotubes were dispersed well in the composites and were completely wrapped by PAN matrix. Because of the strong interfacial interaction between CNTs and PAN, the CNTs/PAN application performance will be enhanced correspondingly, such as the mechanical properties and the electrical conductivity. It was concluded that the hot-stretched CNTs/PAN nanofibers can be used as a potential precursor to produce high-performance carbon composites.

  3. Electrospun nanofibers: New generation materials for advanced applications

    Energy Technology Data Exchange (ETDEWEB)

    Thenmozhi, S. [Inorganic & Nanomaterials Research Laboratory, Department of Chemistry, Bharathiar University, Coimbatore 641 046 (India); DRDO-BU CLS, Bharathiar University Campus, Coimbatore 641 046 (India); Dharmaraj, N., E-mail: dharmaraj@buc.edu.in [Inorganic & Nanomaterials Research Laboratory, Department of Chemistry, Bharathiar University, Coimbatore 641 046 (India); Kadirvelu, K. [DRDO-BU CLS, Bharathiar University Campus, Coimbatore 641 046 (India); Kim, Hak Yong [Department of Textile Engineering, Chonbuk National University, Chonju 561-756 (Korea, Republic of)

    2017-03-15

    Highlights: • A review covering important aspects of electrospinning technique is presented. • Applications of nanofibers in various fields are reviewed. • Possibility to up-scale electrospinning technique to industry also included. - Abstract: Electrospinning (E-spin) is a unique technique to fabricate polymeric as well as metal oxide nanofibers. Research on electrospun nanofibers is a very active field in material science owing to their novel applications in diverse domains. The main focus of this review is to provide an insight into E-spin technique by understanding the working principle, influencing parameters and applications of nanofibers in different walks of life. Several hundreds of papers are published on the preparation, modification and applications of nanofibers produced by E-spin technique in the areas like sensor development, decontamination, energy storage, biomedical and catalysis etc. Details on the industrial scale development of E-spin technique, current scenario and future developments are also covered in this review.

  4. Mechanically enhanced electrospun nanofibers for wastewater treatment

    Science.gov (United States)

    Yalcinkaya, Fatma

    2017-11-01

    A novel high-performance polyamide 6, polyacrylonitrile and polyvinylidene fluoride nanofibers were fabricated using industrial production Nanospider equipment for liquid filtration as microfilters. The application of nanofibers has been hindered by their poor mechanical strength. This work developed a feasible approach to preparing mechanically strong nanofiber webs. The mechanical strength of the nanofibers was enhanced using special lamination technique on a supporting layer. Experimental results show that the mechanical strength of the nanofibers enhanced more than 5 times while high porosity and liquid permeability retain. The separation results indicate that nanofibers have a potential to be used in liquid filters.

  5. Improvement of electrospun polymer fiber meshes pore size by femtosecond laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Rebollar, Esther, E-mail: e.rebollar@iqfr.csic.es [Departamento de Fisica Aplicada, E.T.S.I. Industriales, Universidad de Vigo, Rua Maxwell s/n, Campus Lagoas-Marcosende, 36310 Vigo (Spain); Cordero, Diego [Departamento de Fisica Aplicada, E.T.S.I. Industriales, Universidad de Vigo, Rua Maxwell s/n, Campus Lagoas-Marcosende, 36310 Vigo (Spain); Martins, Albino [3B' s Research Group-Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4806-909 Taipas, Guimaraes (Portugal); Chiussi, Stefano [Departamento de Fisica Aplicada, E.T.S.I. Industriales, Universidad de Vigo, Rua Maxwell s/n, Campus Lagoas-Marcosende, 36310 Vigo (Spain); Reis, Rui L.; Neves, Nuno M. [3B' s Research Group-Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, 4806-909 Taipas, Guimaraes (Portugal); Leon, Betty [Departamento de Fisica Aplicada, E.T.S.I. Industriales, Universidad de Vigo, Rua Maxwell s/n, Campus Lagoas-Marcosende, 36310 Vigo (Spain)

    2011-02-15

    Polymer meshes have recently attracted great attention due to their great variety of applications in fields such as tissue engineering and drug delivery. Poly({epsilon}-caprolactone) nanofibers were prepared by electrospinning giving rise to porous meshes. However, for some applications in tissue engineering where, for instance, cell migration into the inner regions of the mesh is aimed, the pore size obtained by conventional techniques is too narrow. To improve the pore size, laser irradiation with femtosecond pulses (i.e., negligible heat diffusion into the polymer material and confined excitation energy) is performed. A detailed study of the influence of the pulse energy, pulse length, and number of pulses on the topography of electrospun fiber meshes has been carried out, and the irradiated areas have been studied by scanning electron microscopy, contact angle measurements and spectroscopic techniques. The results show that using the optimal laser parameters, micropores are formed and the nature of the fibers is preserved.

  6. Hydrophilized polycaprolactone nanofiber mesh-embedded poly(glycolic-co-lactic acid) membrane for effective guided bone regeneration.

    Science.gov (United States)

    Cho, Wan Jin; Kim, Jun Ho; Oh, Se Heang; Nam, Hyun Hee; Kim, Jin Man; Lee, Jin Ho

    2009-11-01

    A novel guided bone regeneration (GBR) membrane was fabricated by an immersion precipitation of poly (glycolic-co-lactic acid) (PLGA)/Pluronic F127 solution impregnated in an electrospun polycaprolactone (PCL)/Tween 80 nanofiber mesh. The prepared PCL/Tween 80 nanofiber mesh-embedded PLGA/Pluronic F127 membrane (hydrophilized PCL/PLGA hybrid membrane) had nano-size pores on the top side (which can prevent from fibrous connective tissue infiltration but allow permeation of oxygen and nutrients) and micro-size pores on the bottom side (which can improve adhesiveness with bone). From the comparisons of mechanical properties (tensile and suture pullout strengths), model nutrient (FITC-labeled bovine serum albumin) permeability, and bone regeneration behavior using a rat model (skull bone defect) of the hybrid membrane with those of PLGA/Pluronic F127 membrane (asymmetrically porous, hydrophilized PLGA membrane), PCL/Tween 80 nanofiber mesh (electrospun, hydrophilized PCL nanofiber mesh), and a commercialized GBR membrane, Bio-Gide (collagen type I/III membrane), it was observed that the PCL/PLGA hybrid membrane seems to be highly desirable as a GBR membrane for the selective permeability caused by its unique morphology and osteoconductivity provided by several tens micro-size pores of the bottom side as well as the excellent mechanical strengths by the hybridization of porous PLGA membrane and PCL nanofiber mesh. (c) 2008 Wiley Periodicals, Inc.

  7. Perspective of electrospun nanofibers in energy and environment

    Directory of Open Access Journals (Sweden)

    Jayaraman Sundaramurthy

    2014-06-01

    Full Text Available This review summarizes the recent developments of electrospun semiconducting metal oxide/polymer composite nanostructures in energy and environment related applications. Electrospinning technique has the advantage of synthesizing nanostructures with larger surface to volume ratio, higher crystallinity with phase purity and tunable morphologies like nanofibers, nanowires, nanoflowers and nanorods. The electrospun nanostructures have exhibited unique electrical, optical and catalytic properties than the bulk counter parts as well as nanomaterials synthesized through other approaches. These nanostructures have improved diffusion and interaction of molecules, transfer of electrons along the matrix and catalytic properties with further surface modification and functionalization with combination of metals and metal oxides.

  8. Chemistry on electrospun polymeric nanofibers: merely routine chemistry or a real challenge?

    Science.gov (United States)

    Agarwal, Seema; Wendorff, Joachim H; Greiner, Andreas

    2010-08-03

    Nanofiber-based non-wovens can be prepared by electrospinning. The chemical modification of such nanofibers or chemistry using nanofibers opens a multitude of application areas and challenges. A wealth of chemistry has been elaborated in recent years on and with electrospun nanofibers. Known methods as well as new methods have been applied to modify the electrospun nanofibers and thereby generate new materials and new functionalities. This Review summarizes and sorts the chemistry that has been reported in conjunction with electrospun nanofibers. The major focus is on catalysis and nanofibers, enzymes and nanofibers, surface modification for biomedical and specialty applications, coatings of fibers, crosslinking, and bulk modifications. A critical focus is on the question: what could make chemistry on or with nanofibers different from bulk chemistry? Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Engineered Polymer Composites Through Electrospun Nanofiber Coating of Fiber Tows

    Science.gov (United States)

    Kohlman, Lee W.; Bakis, Charles; Williams, Tiffany S.; Johnston, James C.; Kuczmarski, Maria A.; Roberts, Gary D.

    2014-01-01

    Composite materials offer significant weight savings in many aerospace applications. The toughness of the interface of fibers crossing at different angles often determines failure of composite components. A method for toughening the interface in fabric and filament wound components using directly electrospun thermoplastic nanofiber on carbon fiber tow is presented. The method was first demonstrated with limited trials, and then was scaled up to a continuous lab scale process. Filament wound tubes were fabricated and tested using unmodified baseline towpreg material and nanofiber coated towpreg.

  10. Electrospun Carbon Nanotube-Reinforced Nanofiber.

    Science.gov (United States)

    Kim, Sung Mm; Hee Kim, Sung; Choi, Myong Soo; Lee, Jun Young

    2016-03-01

    We fabricated multi-walled carbon nanotube (MWNT) reinforced polyurethane (PU) nanofiber (MWNT-PU) web via electrospinning. In order to optimize the electrospinning conditions, we investigated the effects of various parameters including kind of solvent, viscosity of the spinning solution, and flow rate on the spinnability and properties of nanofiber. N,N-dimethylformamide (DMF), tetrahydrofuran (THF) and their mixture with various volume ratio were used as the spinning solvent. Morphology of the nanofiber was studied using scanning electron microscope (SEM) and transmission electron microscope (TEM), confirming successful fabrication of MWNT-PU nanofiber web with uniform dispersion of MWNT in longitudinal direction of the fiber. The MWNT-PU nanofiber web exhibited two times higher tensile strength than PU nanofiber web. We also fabricated electrically conducting MWNT-PU nanofiber web by coating poly(3,4-ehtylenedioxythiophene) (PEDOT) on the surface of MWNT-PU nanofiber web for electromagnetic interference (EMI) shielding application. The electromagnetic interference shielding effectiveness (EMI SE) was quite high as 25 dB in the frequency range from 50 MHz to 10 GHz.

  11. Development of Protective Clothing against Nanoparticle Based on Electrospun Nanofibers

    Directory of Open Access Journals (Sweden)

    M. Faccini

    2012-01-01

    Full Text Available In this paper, the development of efficient protective clothing against nanoparticulate aerosols is presented. Nanofibrous mats of polyamide 6 (PA6 were deposited onto a nonwoven viscose substrate by electrospinning technique. The influence of electrospinning parameters, including solution concentration, viscosity, and conductivity, was studied for the production of nonwovens with controlled fiber diameter showing a size distribution ranging from 66 to 195 nm. By varying several process parameters, textiles with different thickness of the nanofiber layer and thus air permeability were obtained. A hot-press lamination process using a thermoplastic resin as glue was applied to improve the adhesion of the nanofiber layer onto the textile support. After 1500 cycles of repeated compression and torsion, the nanofiber layer was still firmly attached to the support, while mechanical damage is visible in some areas. The penetration of NaCl particles with diameter ranging from 15 to 300 nm through the electrospun textiles was found to be strongly dependent on nanofiber layer thickness. A really thin nanofiber coating provides up to 80% retention of 20 nm size particles and over 50% retention of 200 nm size nanoparticles. Increasing the thickness of the nanofiber mat, the filtration efficiency was increased to over 99% along the whole nanoparticle range. The results obtained highlight the potential of nanofibers in the development of efficient personal protective equipments against nanoparticles.

  12. Effect of micropatterning induced surface hydrophobicity on drug release from electrospun cellulose acetate nanofibers

    Science.gov (United States)

    Adepu, Shivakalyani; Gaydhane, Mrunalini K.; Kakunuri, Manohar; Sharma, Chandra S.; Khandelwal, Mudrika; Eichhorn, Stephen J.

    2017-12-01

    Sustained release and prevention of burst release for low half-life drugs like Diclofenac sodium is crucial to prevent drug related toxicity. Electrospun nanofibers have emerged recently as potential carrier materials for controlled and sustained drug release. Here, we present a facile method to prevent burst release by tuning the surface wettability through template assisted micropatterning of drug loaded electrospun cellulose acetate (CA) nanofibers. A known amount of drug (Diclofenac sodium) was first mixed with CA and then electrospun in the form of a nanofabric. This as-spun network was hydrophilic in nature. However, when electrospinning was carried out through non-conducting templates, viz nylon meshes with 50 and 100 μm size openings, two kinds of hydrophobic micro-patterned CA nanofabrics were produced. In vitro transdermal testing of our nanofibrous mats was carried out; these tests were able to show that it would be possible to create a patch for transdermal drug release. Further, our results show that with optimized micro-patterned dimensions, a zero order sustained drug release of up to 12 h may be achieved for the transdermal system when compared to non-patterned samples. This patterning caused a change in the surface wettability, to a hydrophobic surface, resulting in a controlled diffusion of the hydrophilic drug. Patterning assisted in controlling the initial burst release, which is a significant finding especially for low half-life drugs.

  13. Performance Enhancement of Dental Composites Using Electrospun Nanofibers

    Directory of Open Access Journals (Sweden)

    H. Dodiuk-Kenig

    2008-01-01

    Full Text Available The objective of the present study is to investigate the effect of electrospun nanofiber reinforcement on the properties of commercially available, hyperbranched polymer modified (Hybrane, 0.3 wt.% DSM dental formulations. The emergence of functionalized nanoscale reinforcements having large surface area (hundreds of square meters/gram has enabled the design of novel nanocomposites with new and complex structures leading to enhanced mechanical and physical properties. Electrospun nanofibers from a range of polymer chemistries (PVOH, PLLA, Nylon 6 have been investigated as a reinforcing phase at levels between 0.01 and 0.3 wt.%, with and without a silane coupling agent surface treatment. The experimental results indicate that 0.05 wt.% reinforcement with 250 nm diameter PVOH nanofibers leads to a 30% improvement in compressive strength, coupled with a shrinkage reduction of about 50%. Electrospun fiber reinforcement by other chemistries or at other diameters showed either no property improvement or led to property loss.

  14. Antibacterial activity of polyacrylonitrile-chitosan electrospun nanofibers.

    Science.gov (United States)

    Kim, Sam Soo; Lee, Jaewoong

    2014-02-15

    Polyacrylonitrile (PAN)-chitosan double-face films and nanofibers were manufactured. PAN and a chitosan salt were dissolved in dimethyl sulfoxide, and then thin-layered on a glass plate or electro-spun followed by coagulation in sodium hydroxide solution. The morphology of the PAN-chitosan double-face films and nanofibers was analyzed by scanning electron microscopy. The thermal behavior and the glass transition temperature of PAN-chitosan blends were assessed by differential scanning calorimetry and dynamic mechanical analysis, respectively. The antibacterial efficacy was measured by a swatch test with bacterial suspensions. The PAN-chitosan nanofibers produced a 5-log reduction against Escherichia coli, Staphylococcus aureus, and Micrococcus luteus. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Biomedical applications of ferulic acid encapsulated electrospun nanofibers.

    Science.gov (United States)

    Vashisth, Priya; Kumar, Naresh; Sharma, Mohit; Pruthi, Vikas

    2015-12-01

    Ferulic acid is a ubiquitous phytochemical that holds enormous therapeutic potential but has not gained much consideration in biomedical sector due to its less bioavailability, poor aqueous solubility and physiochemical instability. In present investigation, the shortcomings associated with agro-waste derived ferulic acid were addressed by encapsulating it in electrospun nanofibrous matrix of poly (d,l-lactide-co-glycolide)/polyethylene oxide. Fluorescent microscopic analysis revealed that ferulic acid predominantly resides in the core of PLGA/PEO nanofibers. The average diameters of the PLGA/PEO and ferulic acid encapsulated PLGA/PEO nanofibers were recorded as 125 ± 65.5 nm and 150 ± 79.0 nm, respectively. The physiochemical properties of fabricated nanofibers are elucidated by IR, DSC and NMR studies. Free radical scavenging activity of fabricated nanofibers were estimated using di(phenyl)-(2,4,6-trinitrophenyl)iminoazanium (DPPH) assay. 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay confirmed the cytotoxicity of ferulic acid encapsulated nanofibers against hepatocellular carcinoma (HepG2) cells. These ferulic acid encapsulated nanofibers could be potentially explored for therapeutic usage in biomedical sector.

  16. Wet-Laid Meets Electrospinning: Nonwovens for Filtration Applications from Short Electrospun Polymer Nanofiber Dispersions.

    Science.gov (United States)

    Langner, Markus; Greiner, Andreas

    2016-02-01

    Dispersions of short electrospun fibers are utilized for the preparation of nanofiber nonwovens with different weight area on filter substrates. The aerosol filtration efficiencies of suspension-borne nanofiber nonwovens are compared to nanofiber nonwovens prepared directly by electrospinning with similar weight area. The filtration efficiencies are found to be similar for both types of nonwovens. With this, a large potential opens for processing, design, and application of new nanofiber nonwovens obtained by wet-laying of short electrospun nanofiber suspensions. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Dehydration driven changes in the structure and mechanical behavior of electrospun poly (vinyl alcohol) nanofibers

    International Nuclear Information System (INIS)

    Bansal, Ankita; Sinha, Arvind

    2012-01-01

    Electrospun nanofibers of poly (vinyl alcohol) (PVA) are well known for their possible application in different fields, ranging from packaging to tissue engineering. However, biomedical application of these nanofibers gets limited due to its rapid disintegration in water, causing mechanical instability. Addressing this issue, the present manuscript reports ethanol induced dehydration of electrospun PVA nanofibers, and its effects on the structure and mechanical properties of the electrospun system. A systematic variation in the structure and mechanical stability of nanofibers as a function of PVA concentration has also been established in the both hydrated and dehydrated states. - Highlights: ► Study reports structure-property correlation of dehydrated PVA nanofibers. ► Results confirm symmetrical reversal of properties in two states. ► Experimental results are in confirmation with the fusion model of nanofibers.

  18. Electrospun gelatin/polyurethane blended nanofibers for wound healing

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Eun; Heo, Dong Nyoung; Lee, Jung Bok; Kwon, Il Keun [Department of Oral Biology, School of Dentistry, Kyung Hee University, Seoul 130-701 (Korea, Republic of); Kim, Jong Ryul; Park, Sang Hyuk [Conservative Dentistry and Institute of Oral Biology, School of Dentistry, Kyung Hee University, Seoul 130-701 (Korea, Republic of); Jeon, Seong Ho, E-mail: kwoni@khu.ac.k [College of Pharmacy, Kangwon National University, Chuncheon 200-701 (Korea, Republic of)

    2009-08-15

    In this study, we prepared a blended nanofiber scaffold using synthetic and natural polymers, polyurethane (PU) and gelatin respectively, using the electrospinning method to prepare a material for wound dressing. In order to confirm the properties of this gelatin/PU blended nanofiber scaffold, we performed scanning electron microscopy, atomic force microscopy, attenuated total reflectance Fourier-transform infrared spectroscopy, thermal gravimetric analysis, contact angle, water uptake, mechanical property, recovery, and degradation tests, and cellular response. The results obtained indicate that the mean diameter of these nanofibers was uniformly electrospun and ranged from 0.4 to 2.1{mu}m. According to the results, when the amount of gelatin in the blended solution decreased, the contact angle increased and water uptake of the scaffold decreased concurrently. In the mechanical tests, the blended nanofibrous scaffolds were elastic, and elasticity increased as the total amount of PU increased. Moreover, as the total amount of gelatin increased, the cell proliferation increased with the same amount of culture time. Therefore, this gelatin/PU blended nanofiber scaffold has potential application for use as a wound dressing.

  19. Electrospun Nanofiber Scaffolds with Gradations in Fiber Organization

    Science.gov (United States)

    Khandalavala, Karl; Jiang, Jiang; Shuler, Franklin D.; Xie, Jingwei

    2015-01-01

    The goal of this protocol is to report a simple method for generating nanofiber scaffolds with gradations in fiber organization and test their possible applications in controlling cell morphology/orientation. Nanofiber organization is controlled with a new fabrication apparatus that enables the gradual decrease of fiber organization in a scaffold. Changing the alignment of fibers is achieved through decreasing deposition time of random electrospun fibers on a uniaxially aligned fiber mat. By covering the collector with a moving barrier/mask, along the same axis as fiber deposition, the organizational structure is easily controlled. For tissue engineering purposes, adipose-derived stem cells can be seeded to these scaffolds. Stem cells undergo morphological changes as a result of their position on the varied organizational structure, and can potentially differentiate into different cell types depending on their locations. Additionally, the graded organization of fibers enhances the biomimicry of nanofiber scaffolds so they more closely resemble the natural orientations of collagen nanofibers at tendon-to-bone insertion site compared to traditional scaffolds. Through nanoencapsulation, the gradated fibers also afford the possibility to construct chemical gradients in fiber scaffolds, and thereby further strengthen their potential applications in fast screening of cell-materials interaction and interfacial tissue regeneration. This technique enables the production of continuous gradient scaffolds, but it also can potentially produce fibers in discrete steps by controlling the movement of the moving barrier/mask in a discrete fashion. PMID:25938562

  20. Stability of β-carotene in polyethylene oxide electrospun nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Peinado, I., E-mail: irpeipar@upvnet.upv.es [Free University of Bolzano, Piazza Università 5, 39100 Bolzano (Italy); Mason, M.; Romano, A. [Free University of Bolzano, Piazza Università 5, 39100 Bolzano (Italy); Biasioli, F. [Department of Food Quality and Nutrition, Research and Innovation Centre, Fondazione Edmund Mach (FEM), via E. Mach 1, 38010 San Michele all ‘Adige, TN (Italy); Scampicchio, M., E-mail: matteo.scampicchio@unibz.it [Free University of Bolzano, Piazza Università 5, 39100 Bolzano (Italy)

    2016-05-01

    Highlights: • β-carotene was incorporated into PEO-nanofibers by electrospinning. • Properties of the fibers were analyzed by SEM, color analysis, and DSC. • TGA coupled to PTR–ms resulted promising to online-monitoring thermal degradation. • Thermal stability of βc increased after encapsulation into the PEO-nanofibers. - Abstract: β-carotene (βc) was successfully incorporated into electrospun nanofibers of poly-(ethylene oxide) (PEO) with the aim of prolonging its shelf life and thermal stability. The physical and thermal properties of the βc-PEO-nanofibers were determined by scanning electron microscopy (SEM), color analysis, and differential scanning calorimetry (DSC). The nanofibers of PEO and βc-PEO exhibited average fiber diameters of 320 ± 46 and 230 ± 21 nm, with colorimetric coordinates L* = 95.7 ± 2.4 and 89.4 ± 4.6 and b* = −0.5 ± 0.1 and 6.2 ± 3.0 respectively. Thermogravimetric analysis coupled with Proton Transfer–Mass Spectroscopy (TGA/PTR–ms) demonstrated that coated βc inside PEO nanofibers increased thermal stability when compared to standard βc in powder form. In addition, β-carotene in the membranes showed higher stability during storage when compared with β-carotene in solution with a decrease in concentration of 57 ± 4% and 70 ± 2% respectively, thus should extend the shelf life of this compound. Also, TGA coupled with PTR–MS resulted in a promising technique to online-monitoring thermal degradation.

  1. Highly stretchable electrospun conducting polymer nanofibers

    Science.gov (United States)

    Boubée de Gramont, Fanny; Zhang, Shiming; Tomasello, Gaia; Kumar, Prajwal; Sarkissian, Andranik; Cicoira, Fabio

    2017-08-01

    Biomedical electronics research targets both wearable and biocompatible electronic devices easily adaptable to specific functions. To achieve such goals, stretchable organic electronic materials are some of the most intriguing candidates. Herein, we develop highly stretchable poly-(3,4-ethylenedioxythiphene) (PEDOT) doped with tosylate (PEDOT:Tos) nanofibers. A two-step process involving electrospinning of a carrier polymer (with oxidant) and vapor phase polymerization was used to produce fibers on a polydimethylsiloxane substrate. The fibers can be stretched up to 140% of the initial length maintaining high conductivity.

  2. Electrospun nanofiber reinforcement of dental composites with electromagnetic alignment approach

    International Nuclear Information System (INIS)

    Uyar, Tansel; Çökeliler, Dilek; Doğan, Mustafa; Koçum, Ismail Cengiz; Karatay, Okan; Denkbaş, Emir Baki

    2016-01-01

    Polymethylmethacrylate (PMMA) is commonly used as a base acrylic denture material with benefits of rapid and easy handling, however, when it is used in prosthetic dentistry, fracturing or cracking problems can be seen due to the relatively low strength issues. Besides, acrylic resin is the still prominent material for denture fabrication due to its handy and low cost features. Numerous proposed fillers that are used to produce PMMA composites, however electrospun polyvinylalcohol (PVA) nanofiber fillers for production of PMMA composite resins are not studied as much as the others. The other focus of the practice is to compare both mechanical properties and efficiency of aligned fibers versus non-aligned PVA nanofibers in PMMA based dental composites. Field-controlled electrospinning system is manufactured and provided good alignment in lab scale as one of contributions. Some novel auxiliary electrodes in controlled structure are augmented to obtain different patterns of alignment with a certain range of fiber diameters. Scanning electron microscopy is used for physical characterization to determine the range of fiber diameters. Non-woven fiber has no unique pattern due to chaotic nature of electrospinning process, but aligned fibers have round pattern or crossed lines. These produced fibers are structured as layer-by-layer form with different features, and these features are used in producing PMMA dental composites with different volume ratios. The maximum flexural strength figure shows that fiber load by weight of 0.25% w/w and above improves in the maximum level. As a result, mechanical properties of PMMA dental composites are improved by using PVA nanofibers as a filler, however the improvement was higher when aligned PVA nanofibers are used. The maximum values were 5.1 MPa (flexural strength), 0.8 GPa (elastic modulus), and 170 kJ/m 3 (toughness) in three-point bending test. In addition to the positive results of aligned and non-aligned nanofibers it was found

  3. Electrospun nanofiber reinforcement of dental composites with electromagnetic alignment approach

    Energy Technology Data Exchange (ETDEWEB)

    Uyar, Tansel [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Çökeliler, Dilek, E-mail: cokeliler@baskent.edu.tr [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Doğan, Mustafa [Department of Electrical and Electronics Engineering, Başkent University, Ankara 06180 (Turkey); Koçum, Ismail Cengiz [Department of Biomedical Engineering, Başkent University Bağlıca Campus, 06530 Ankara (Turkey); Karatay, Okan [Department of Electrical and Electronics Engineering, Başkent University, Ankara 06180 (Turkey); Denkbaş, Emir Baki [Department of Chemistry, Biochemistry Division, Hacettepe University, Ankara (Turkey)

    2016-05-01

    Polymethylmethacrylate (PMMA) is commonly used as a base acrylic denture material with benefits of rapid and easy handling, however, when it is used in prosthetic dentistry, fracturing or cracking problems can be seen due to the relatively low strength issues. Besides, acrylic resin is the still prominent material for denture fabrication due to its handy and low cost features. Numerous proposed fillers that are used to produce PMMA composites, however electrospun polyvinylalcohol (PVA) nanofiber fillers for production of PMMA composite resins are not studied as much as the others. The other focus of the practice is to compare both mechanical properties and efficiency of aligned fibers versus non-aligned PVA nanofibers in PMMA based dental composites. Field-controlled electrospinning system is manufactured and provided good alignment in lab scale as one of contributions. Some novel auxiliary electrodes in controlled structure are augmented to obtain different patterns of alignment with a certain range of fiber diameters. Scanning electron microscopy is used for physical characterization to determine the range of fiber diameters. Non-woven fiber has no unique pattern due to chaotic nature of electrospinning process, but aligned fibers have round pattern or crossed lines. These produced fibers are structured as layer-by-layer form with different features, and these features are used in producing PMMA dental composites with different volume ratios. The maximum flexural strength figure shows that fiber load by weight of 0.25% w/w and above improves in the maximum level. As a result, mechanical properties of PMMA dental composites are improved by using PVA nanofibers as a filler, however the improvement was higher when aligned PVA nanofibers are used. The maximum values were 5.1 MPa (flexural strength), 0.8 GPa (elastic modulus), and 170 kJ/m{sup 3} (toughness) in three-point bending test. In addition to the positive results of aligned and non-aligned nanofibers it was

  4. Origin of high propagation loss in electrospun polymer nanofibers

    Directory of Open Access Journals (Sweden)

    Yuya Ishii

    2014-06-01

    Full Text Available We evaluate optical propagation loss (α in electrospun poly(methyl methacrylate (PMMA nanofibers with different wavelength (λ and determine the origin of the loss. Aligned single electrospun nanofibers composed of PMMA and a small amount of an organic dye are fabricated with an average diameter of approximately 640 nm. After cladding seven fiber samples, α is evaluated to be 26–62 dB cm−1 at wavelengths 590−680 nm. Moreover, α depended linearly on λ−4, and from the fitting functions we determined the ratio of the following two possible losses for α: loss at the interface between the fiber-core and cladding because of non-uniformity within the fibers (αun, and loss because of excess light scattering in the fibers resulting from density inhomogeneity of PMMA (αsc. For the fibers, αun is evaluated to be 6.9–22 dB cm−1, which represents 19%–50% of α at λ of 650 nm with α ∼ αun + αsc. Thus, we conclude that the high α in these fibers originates from both their poor uniformity and density inhomogeneity. Furthermore, a quantitative investigation of uniformity in the individual fibers revealed that the root mean square roughness ranges from 5.5 nm to 9.0 nm and the theoretical value of αun was ∼1 dB cm−1 showing reasonable agreement with experimental data. These findings hold for low-loss polymer nanofiber waveguides, which have high aspect ratio and fine patterning even in three dimensions.

  5. Synthesis of Flexible Aerogel Composites Reinforced with Electrospun Nanofibers and Microparticles for Thermal Insulation

    Directory of Open Access Journals (Sweden)

    Huijun Wu

    2013-01-01

    Full Text Available Flexible silica aerogel composites in intact monolith of 12 cm were successfully fabricated by reinforcing SiO2 aerogel with electrospun polyvinylidene fluoride (PVDF webs via electrospinning and sol-gel processing. Three electrospun PVDF webs with different microstructures (e.g., nanofibers, microparticles, and combined nanofibers and microparticles were fabricated by regulating electrospinning parameters. The as-electrospun PVDF webs with various microstructures were impregnated into the silica sol to synthesize the PVDF/SiO2 composites followed by solvent exchange, surface modification, and drying at ambient atmosphere. The morphologies of the PVDF/SiO2 aerogel composites were characterized and the thermal and mechanical properties were measured. The effects of electrospun PVDF on the thermal and mechanical properties of the aerogel composites were evaluated. The aerogel composites reinforced with electrospun PVDF nanofibers showed intact monolith, improved strength, and perfect flexibility and hydrophobicity. Moreover, the aerogel composites reinforced with the electrospun PVDF nanofibers had the lowest thermal conductivity (0.028 W·m−1·K−1. It indicates that the electrospun PVDF nanofibers could greatly improve the mechanical strength and flexibility of the SiO2 aerogels while maintaining a lower thermal conductivity, which provides increasing potential for thermal insulation applications.

  6. Proliferation of Genetically Modified Human Cells on Electrospun Nanofiber Scaffolds

    Directory of Open Access Journals (Sweden)

    Mandula Borjigin

    2012-01-01

    Full Text Available Gene editing is a process by which single base mutations can be corrected, in the context of the chromosome, using single-stranded oligodeoxynucleotides (ssODNs. The survival and proliferation of the corrected cells bearing modified genes, however, are impeded by a phenomenon known as reduced proliferation phenotype (RPP; this is a barrier to practical implementation. To overcome the RPP problem, we utilized nanofiber scaffolds as templates on which modified cells were allowed to recover, grow, and expand after gene editing. Here, we present evidence that some HCT116-19, bearing an integrated, mutated enhanced green fluorescent protein (eGFP gene and corrected by gene editing, proliferate on polylysine or fibronectin-coated polycaprolactone (PCL nanofiber scaffolds. In contrast, no cells from the same reaction protocol plated on both regular dish surfaces and polylysine (or fibronectin-coated dish surfaces proliferate. Therefore, growing genetically modified (edited cells on electrospun nanofiber scaffolds promotes the reversal of the RPP and increases the potential of gene editing as an ex vivo gene therapy application.

  7. Antimicrobial electrospun silver-, copper- and zinc-doped polyvinylpyrrolidone nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Quirós, Jennifer [Department of Chemical Engineering, University of Alcalá, 28871 Alcalá de Henares, Madrid (Spain); Borges, João P. [CENIMAT/I3N, Departamento de Ciência dos Materiais, Faculdade de Ciências e Tecnologia, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Boltes, Karina [Department of Chemical Engineering, University of Alcalá, 28871 Alcalá de Henares, Madrid (Spain); Madrid Institute for Advanced Studies of Water (IMDEA Agua), Parque Científico Tecnológico, E-28805, Alcalá de Henares, Madrid (Spain); Rodea-Palomares, Ismael [Departamento de Biología, Facultad de Ciencias, Universidad Autónoma de Madrid, Cantoblanco, E-28049 Madrid (Spain); Rosal, Roberto [Department of Chemical Engineering, University of Alcalá, 28871 Alcalá de Henares, Madrid (Spain); Madrid Institute for Advanced Studies of Water (IMDEA Agua), Parque Científico Tecnológico, E-28805, Alcalá de Henares, Madrid (Spain)

    2015-12-15

    Highlights: • Electrospun polyvinylpyrrolidone (PVP) nanofibers containing silver, copper, and zinc. • Antimicrobial effect for the bacteria Staphylococcus aureus and Escherichia coli. • Silver strongly reduced colony forming units and bacterial viability. • Silver, copper, and zinc led to a significant increase of non-viable cells on mats. - Abstract: The use of electrospun polyvinylpyrrolidone (PVP) nanofibers containing silver, copper, and zinc nanoparticles was studied to prepare antimicrobial mats using silver and copper nitrates and zinc acetate as precursors. Silver became reduced during electrospinning and formed nanoparticles of several tens of nanometers. Silver nanoparticles and the insoluble forms of copper and zinc were dispersed using low molecular weight PVP as capping agent. High molecular weight PVP formed uniform fibers with a narrow distribution of diameters around 500 nm. The fibers were converted into an insoluble network using ultraviolet irradiation crosslinking. The efficiency of metal-loaded mats against the bacteria Escherichia coli and Staphylococcus aureus was tested for different metal loadings by measuring the inhibition of colony forming units and the staining with fluorescent probes for metabolic viability and compromised membranes. The assays included the culture in contact with mats and the direct staining of surface attached microorganisms. The results indicated a strong inhibition for silver-loaded fibers and the absence of significant amounts of viable but non-culturable microorganisms. Copper and zinc-loaded mats also decreased the metabolic activity and cell viability, although in a lesser extent. Metal-loaded fibers allowed the slow release of the soluble forms of the three metals.

  8. Electrospun Composite Nanofibers of Semiconductive Polymers for Coaxial PN Junctions

    Science.gov (United States)

    Serrano, William; Thomas, Sylvia

    The objective of this research is to investigate the conditions under P3HT and Activink, semiconducting polymers, form 1 dimension (1D) coaxial p-n junctions and to characterize their behavior in the presence of UV radiation and organic gases. For the first time, fabrication and characterization of semiconductor polymeric single fiber coaxial arrangements will be studied. Electrospinning, a low cost, fast and reliable method, with a coaxial syringe arrangement will be used to fabricate these fibers. With the formation of fiber coaxial arrangements, there will be investigations of dimensionality crossovers e.g., from one-dimensional (1D) to two-dimensional (2D). Coaxial core/shell fibers have been realized as seen in a recent publication on an electrospun nanofiber p-n heterojunction of oxides (BiFeO3 and TiO2, respectively) using the electrospinning technique with hydrothermal method. In regards to organic semiconducting coaxial p-n junction nanofibers, no reported studies have been conducted, making this study fundamental and essential for organic semiconducting nano devices for flexible electronics and multi-dimensional integrated circuits.

  9. Improvement of Polylactide Properties through Cellulose Nanocrystals Embedded in Poly(Vinyl Alcohol) Electrospun Nanofibers.

    Science.gov (United States)

    López de Dicastillo, Carol; Garrido, Luan; Alvarado, Nancy; Romero, Julio; Palma, Juan Luis; Galotto, Maria Jose

    2017-05-11

    Electrospun nanofibers of poly (vinyl alcohol) (PV) were obtained to improve dispersion of cellulose nanocrystals (CNC) within hydrophobic biopolymeric matrices, such as poly(lactic acid) (PLA). Electrospun nanofibers (PV/CNC) n were successfully obtained with a final concentration of 23% ( w / w ) of CNC. Morphological, structural and thermal properties of developed CNC and electrospun nanofibers were characterized. X-ray diffraction and thermal analysis revealed that the crystallinity of PV was reduced by the electrospinning process, and the incorporation of CNC increased the thermal stability of biodegradable nanofibers. Interactions between CNC and PV polymer also enhanced the thermal stability of CNC and improved the dispersion of CNC within the PLA matrix. PLA materials with CNC lyophilized were also casted in order to compare the properties with materials based on CNC containing nanofibers. Nanofibers and CNC were incorporated into PLA at three concentrations: 0.5%, 1% and 3% (CNC respect to polymer weight) and nanocomposites were fully characterized. Overall, nanofibers containing CNC positively modified the physical properties of PLA materials, such as the crystallinity degree of PLA which was greatly enhanced. Specifically, materials with 1% nanofiber 1PLA(PV/CNC) n presented highest improvements related to mechanical and barrier properties; elongation at break was enhanced almost four times and the permeation of oxygen was reduced by approximately 30%.

  10. Study on superhydrophobic surfaces of octanol grafted electrospun silica nanofibers

    International Nuclear Information System (INIS)

    Meng, Long-Yue; Han, Shunyu; Jiang, Nanzhe; Meng, Wan

    2014-01-01

    In this work, superhydrophobic surfaces were successfully prepared by grafting of octanol on the surface of electrospun silica nanofibers (SNFs). The chemical compositions and microstructures of the prepared SNFs surfaces were investigated by using N 2 full isotherms, Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and contact angle measurements. The results indicate that the surface of SNFs changed from being superhydrophilic to superhydrophobic by octanol surface grafting. The contact angle of the octanol-grafted SNFs was close to 150.2° because their surface was modified by –(CH 2 ) 6 –CH 3 groups. The 3D network of SNFs networks and the low surface energy of the alkyl side chains played important roles in creating the superhydrophobic surface of the SNFs. - Highlights: • Superhydrophobic surface was prepared from electrospinning SNFs and by grafting octanol on their surface. • The surface of SNFs changed from superhydrophilic to superhydrophobic. • The CA of MSNFs became 150.2° because of interactions between grafted octyl groups

  11. Study on superhydrophobic surfaces of octanol grafted electrospun silica nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Long-Yue [Key Laboratory of Natural Resources of Changbai Mountain and Functional Molecules, Yanbian University, Yanji 133002 (China); Department of Chemical Engineering, College of Engineering, Yanbian University, 977 Gongyuan Road, Yanji 133002 (China); Han, Shunyu; Jiang, Nanzhe [Department of Chemical Engineering, College of Engineering, Yanbian University, 977 Gongyuan Road, Yanji 133002 (China); Meng, Wan, E-mail: mengw@ybu.edu.cn [Department of Chemical Engineering, College of Engineering, Yanbian University, 977 Gongyuan Road, Yanji 133002 (China)

    2014-12-15

    In this work, superhydrophobic surfaces were successfully prepared by grafting of octanol on the surface of electrospun silica nanofibers (SNFs). The chemical compositions and microstructures of the prepared SNFs surfaces were investigated by using N{sub 2} full isotherms, Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and contact angle measurements. The results indicate that the surface of SNFs changed from being superhydrophilic to superhydrophobic by octanol surface grafting. The contact angle of the octanol-grafted SNFs was close to 150.2° because their surface was modified by –(CH{sub 2}){sub 6}–CH{sub 3} groups. The 3D network of SNFs networks and the low surface energy of the alkyl side chains played important roles in creating the superhydrophobic surface of the SNFs. - Highlights: • Superhydrophobic surface was prepared from electrospinning SNFs and by grafting octanol on their surface. • The surface of SNFs changed from superhydrophilic to superhydrophobic. • The CA of MSNFs became 150.2° because of interactions between grafted octyl groups.

  12. Analysis of the Comprehensive Tensile Relationship in Electrospun Silk Fibroin/Polycaprolactone Nanofiber Membranes.

    Science.gov (United States)

    Yin, Yunlei; Pu, Dandan; Xiong, Jie

    2017-12-07

    The mechanical properties of electrospun nanofiber membranes are critical for their applications. A clear understanding of the mechanical properties that result from the characteristics of the individual fiber and membrane microstructure is vital in the design of fiber composites. In this reported study, silk fibroin (SF)/polycaprolactone (PCL) composite nanofiber membranes were preparedusing an electrostatic spinning technology. The nanofiber orientation distribution (FOD) of the membrane was analyzed using multi-layer image fusion technology, and the results indicated the presence of an approximately uniform distribution of fibers in the electrospun membranes. The relationship between the single nanofiber and the membrane was established by analyzing the geometrical structure of the cell by employing a representative volume element (RVE) analysis method. The mechanical properties of the 272 nm diameter SF/PCL composite fibers were then predicted using the developed model.

  13. A nanopore-nanofiber mesh biosensor to control DNA translocation

    OpenAIRE

    Squires, Allison; Hersey, Joseph S.; Grinstaff, Mark W.; Meller, Amit

    2013-01-01

    Solid-state nanopores show promise as single-molecule sensors for biomedical applications, but to increase their resolution and efficiency analyte molecules must remain longer in the nanopore sensing volume. Here we demonstrate a novel, facile, and customizable nanopore sensor modification that reduces double stranded DNA translocation velocity by two orders of magnitude or more via interactions outside the nanopore. This is achieved by electrospinning a copolymer nanofiber mesh (NFM) directl...

  14. Enhancing the Mechanical Properties of Electrospun Nanofiber Mats through Controllable Welding at the Cross Points.

    Science.gov (United States)

    Li, Haoxuan; Zhu, Chunlei; Xue, Jiajia; Ke, Qinfei; Xia, Younan

    2017-05-01

    This communication describes a simple and effective method for welding electrospun nanofibers at the cross points to enhance the mechanical properties of their nonwoven mats. The welding is achieved by placing a nonwoven mat of the nanofibers in a capped vial with the vapor of a proper solvent. For polycaprolactone (PCL) nanofibers, the solvent is dichloromethane (DCM). The welding can be managed in a controllable fashion by simply varying the partial pressure of DCM and/or the exposure time. Relative to the pristine nanofiber mat, the mechanical strength of the welded PCL nanofiber mat can be increased by as much as 200%. Meanwhile, such a treatment does not cause any major structural changes, including morphology, fiber diameter, and pore size. This study provides a generic method for improving the mechanical properties of nonwoven nanofiber mats, holding great potential in various applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Fabrication and Characterization of Electrospun Wool Keratin/Poly(vinyl alcohol Blend Nanofibers

    Directory of Open Access Journals (Sweden)

    Shuai Li

    2014-01-01

    Full Text Available Wool keratin/poly(vinyl alcohol (PVA blend nanofibers were fabricated using the electrospinning method in formic acid solutions with different weight ratios of keratin to PVA. The resultant blend nanofibers were characterized by scanning electron microscopy (SEM, Fourier transform infrared (FTIR, X-ray diffraction (XRD, thermal gravimetric analysis (TGA, and tensile test. SEM images showed that the diameter of the blend nanofibers was affected by the content of keratin in blend solution. FTIR and XRD analyses data demonstrated that there were good interactions between keratin and PVA in the blended nanofibers caused by possibly hydrogen bonds. The TGA study revealed that the thermal stability of the blend nanofibers was between those of keratin and PVA. Tensile test indicated that the addition of PVA was able to improve the mechanical properties of the electrospun nanofibers.

  16. Electrospun micro- and nanofiber tubes for functional nervous regeneration in sciatic nerve transections

    Directory of Open Access Journals (Sweden)

    Amadio Stefano

    2008-04-01

    Full Text Available Abstract Background Although many nerve prostheses have been proposed in recent years, in the case of consistent loss of nervous tissue peripheral nerve injury is still a traumatic pathology that may impair patient's movements by interrupting his motor-sensory pathways. In the last few decades tissue engineering has opened the door to new approaches;: however most of them make use of rigid channel guides that may cause cell loss due to the lack of physiological local stresses exerted over the nervous tissue during patient's movement. Electrospinning technique makes it possible to spin microfiber and nanofiber flexible tubular scaffolds composed of a number of natural and synthetic components, showing high porosity and remarkable surface/volume ratio. Results In this study we used electrospun tubes made of biodegradable polymers (a blend of PLGA/PCL to regenerate a 10-mm nerve gap in a rat sciatic nerve in vivo. Experimental groups comprise lesioned animals (control group and lesioned animals subjected to guide conduits implantated at the severed nerve stumps, where the tubular scaffolds are filled with saline solution. Four months after surgery, sciatic nerves failed to reconnect the two stumps of transected nerves in the control animal group. In most of the treated animals the electrospun tubes induced nervous regeneration and functional reconnection of the two severed sciatic nerve tracts. Myelination and collagen IV deposition have been detected in concurrence with regenerated fibers. No significant inflammatory response has been found. Neural tracers revealed the re-establishment of functional neuronal connections and evoked potential results showed the reinnervation of the target muscles in the majority of the treated animals. Conclusion Corroborating previous works, this study indicates that electrospun tubes, with no additional biological coating or drug loading treatment, are promising scaffolds for functional nervous regeneration. They

  17. Design and Characterization of Electrospun Polyamide Nanofiber Media for Air Filtration Applications

    Directory of Open Access Journals (Sweden)

    Jonas Matulevicius

    2014-01-01

    Full Text Available Electrospun polyamide 6 (PA 6 and polyamide 6/6 (PA 6/6 nanofibers were produced in order to investigate their experimental characteristics with the goal of obtaining filtration relevant fiber media. The experimental design model of each PA nanofibers contained the following variables: polymer concentration, ratio of solvents, nanofiber media collection time, tip-to-collector distance, and the deposition voltage. The average diameter of the fibers, their morphology, basis weight, thickness, and resulting media solidity were investigated. Effects of each variable on the essential characteristics of PA 6/6 and PA 6 nanofiber media were studied. The comparative analysis of the obtained PA 6/6 and PA 6 nanofiber characteristics revealed that PA 6/6 had higher potential to be used in filtration applications. Based on the experimental results, the graphical representation—response surfaces—for obtaining nanofiber media with the desirable fiber diameter and basis weight characteristics were derived. Based on the modelling results the nanofiber filter media (mats were fabricated. Filtration results revealed that nanofiber filter media electrospun from PA6/6 8% (w/vol solutions with the smallest fiber diameters (62–66 nm had the highest filtration efficiency (PA6/6_30 = 84.9–90.9% and the highest quality factor (PA6/6_10 = 0.0486–0.0749 Pa−1.

  18. Comparison of Adsorption/Desorption of Volatile Organic Compounds (VOCs) on Electrospun Nanofibers with Tenax TA for Potential Application in Sampling

    OpenAIRE

    Chu, Lanling; Deng, Siwei; Zhao, Renshan; Deng, Jianjun; Kang, Xuejun

    2016-01-01

    The objective of this study was to compare the adsorption/desorption of target compounds on homemade electrospun nanofibers, polystyrene (PS) nanofibers, acrylic resin (AR) nanofibers and PS-AR composite nanofibers with Tenax TA. Ten volatile organic compounds (VOCs) were analyzed by preconcentration onto different sorbents followed by desorption (thermal and solvent orderly) and analysis by capillary gas chromatography. In comparison to Tenax TA, the electrospun nanofibers displayed a signif...

  19. Influence of electrospinning parameters on the structural morphology and diameter of electrospun nanofibers

    CSIR Research Space (South Africa)

    Jacobs, V

    2009-11-01

    Full Text Available that the addition of polyelectrolytes, such as sodium salt of Poly acrylic acid (PAA) and Poly allylamine hydrochloride (PAH), increases the conductivity of PEO solutions and thereby decreases the bead formation in electrospun nanofibers. The increase in applied...

  20. Investigation of Conical Spinneret in Generating More Dense and Compact Electrospun Nanofibers

    Directory of Open Access Journals (Sweden)

    Aya Hamed

    2017-12-01

    Full Text Available Electrospinning is an important, widely used process to generate nanofibers. However, there is still an open window for different designs of both spinneret and collector electrodes to be investigated. This paper introduces the impact of new design of conical spinneret electrode on the generated electrospun nanofibers. In this work, the conical feeder is used to generate electrospun Poly(vinyl alcohol (PVA nanofibers, and being compared to the traditional needle feeder at the same processing conditions. The jet’s mechanism is simulated using discrete bead model along with estimated calculations of both deposition area and fiber radius. The electric field distribution that is around the charged cone is analyzed. Based on both theoretical modeling and experimental measurements, a comparison of mean diameter, deposited area, and the thickness of generated nanofibers is presented related to both conical and needle electrodes. Conical feeder shows clearly compact nanofibers mat in terms of deposition area (spherical deposition of diameter ~6 cm up to half-area of needle deposited nanofibers with high fiber density for the same time of the process. Moreover, the conical electrode is found to have privilege in terms of productivity rate and operation time. This study can be useful in generating localized nanofibers within different applications, such as biomedical tissue scaffolds, textile, and sensors.

  1. Electrospun single-walled carbon nanotube/polyvinyl alcohol composite nanofibers: structure-property relationships

    International Nuclear Information System (INIS)

    Naebe, Minoo; Lin Tong; Wang Xungai; Staiger, Mark P; Dai Liming

    2008-01-01

    Polyvinyl alcohol (PVA) nanofibers and single-walled carbon nanotube (SWNT)/PVA composite nanofibers have been produced by electrospinning. An apparent increase in the PVA crystallinity with a concomitant change in its main crystalline phase and a reduction in the crystalline domain size were observed in the SWNT/PVA composite nanofibers, indicating the occurrence of a SWNT-induced nucleation crystallization of the PVA phase. Both the pure PVA and SWNT/PVA composite nanofibers were subjected to the following post-electrospinning treatments: (i) soaking in methanol to increase the PVA crystallinity, and (ii) cross-linking with glutaric dialdehyde to control the PVA morphology. Effects of the PVA morphology on the tensile properties of the resultant electrospun nanofibers were examined. Dynamic mechanical thermal analyses of both pure PVA and SWNT/PVA composite electrospun nanofibers indicated that SWNT-polymer interaction facilitated the formation of crystalline domains, which can be further enhanced by soaking the nanofiber in methanol and/or cross-linking the polymer with glutaric dialdehyde

  2. A novel electrospun hydroxypropyl methylcellulose/polyethylene oxide blend nanofibers: Morphology and physicochemical properties.

    Science.gov (United States)

    Aydogdu, Ayca; Sumnu, Gulum; Sahin, Serpil

    2018-02-01

    The objective of this study was to fabricate and characterize Hydroxypropyl methylcellulose (HPMC) -based homogenous nanofibers by using electrospinning method. As the concentrations of the solutions increased, viscosity and electrical conductivity of the solutions increased. The morphology of the fibers changed from the beaded structure to the uniform fiber structure by increasing the concentrations of the solutions. Water vapor permeability (WVP) of electrospun HPMC nanofibers decreased with increasing polymer concentration. The shift in wavelengths, the change in intensity of FTIR peaks and melting point depression were the evidence of miscibility of HPMC/PEO blends. Nanofibers showing both melting temperature (T m ) and glass transition temperature (T g ) had semicrystalline structure. By combining PEO with HPMC, the thermal stability of nanofibers was increased. Hence, this study suggests homogenous biopolymer-based nanofibers with low WVP and high thermal stability which can have potential applications in food packaging field. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Coaxial electrospun polyurethane core-shell nanofibers for shape memory and antibacterial nanomaterials

    Directory of Open Access Journals (Sweden)

    2011-02-01

    Full Text Available A novel kind of shape memory polyurethane (SMPU nanofibers with core-shell nanostructure is fabricated using coaxial electrospinning. Transmission electron microscopy (TEM and scanning electron microscopy (SEM results show that nanofibers with core-shell structure or bead-on-string structure can be electrospun successfully from the core solution of polycaprolactone based SMPU (CLSMPU and shell solution of pyridine containing polyurethane (PySMPU. In addition to the excellent shape memory effect with good shape fixity, excellent antibacterial activity against both gramnegative bacteria and gram-positive bacteria are achieved in the CLSMPU-PySMPU core-shell nanofiber. Finally, it is proposed that the antibacterial mechanism should be resulted from the PySMPU shell materials containing amido group in γ position and the high surface area per unit mass of nanofibers. Thus, the CLSMPU-PySMPU core shell nanofibers can be used as both shape memory nanomaterials and antibacterial nanomaterials.

  4. Load bearing enhancement of pin joined composite laminates using electrospun polyacrylonitrile nanofiber mats

    Directory of Open Access Journals (Sweden)

    J. Herwan

    2016-03-01

    Full Text Available Polyacrylonitrile (PAN nanofibers were produced by an electrospinning technique and directly deposited onto carbon fabric to improve the load bearing strength of pin joined composite laminates. Two types of specimens, virgin laminates and nano-modified laminates, were prepared. A modified carbon fiber reinforced polymer (CFRP laminate was fabricated by interleaving electrospun nanofibers at all of the interlayers of an eight-ply woven carbon fiber fabric. The load bearing test results of the pin joined laminates indicated the electrospun PAN nanofibers increased the load bearing strength by 18.9%. In addition, three point bending tests were also conducted to investigate the flexural modulus and flexural strength of both types of laminates. The flexural modulus and flexural strength also increased by 20.9% and 55.91%, respectively.

  5. All-textile flexible supercapacitors using electrospun poly(3,4-ethylenedioxythiophene) nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Laforgue, Alexis [Functional Polymer Systems Group, Industrial Materials Institute, National Research Council Canada, 75, de Mortagne Blvd, Boucherville, Quebec J4B 6Y4 (Canada)

    2011-01-01

    Poly(3,4-ethylenedioxythiophene) (PEDOT) nanofibers were obtained by the combination of electrospinning and vapor-phase polymerization. The fibers had diameters around 350 nm, and were soldered at most intersections, providing a strong dimensional stability to the mats. The nanofiber mats demonstrated very high conductivity (60 {+-} 10 S cm{sup -1}, the highest value reported so far for polymer nanofibers) as well as improved electrochemical properties, due to the ultraporous nature of the electrospun mats. The mats were incorporated into all-textile flexible supercapacitors, using carbon cloths as the current collectors and electrospun polyacrylonitrile (PAN) nanofibrous membranes as the separator. The textile layers were stacked and embedded in a solid electrolyte containing an ionic liquid and PVDF-co-HFP as the host polymer. The resulting supercapacitors were totally flexible and demonstrated interesting and stable performances in ambient conditions. (author)

  6. All-textile flexible supercapacitors using electrospun poly(3,4-ethylenedioxythiophene) nanofibers

    Science.gov (United States)

    Laforgue, Alexis

    Poly(3,4-ethylenedioxythiophene) (PEDOT) nanofibers were obtained by the combination of electrospinning and vapor-phase polymerization. The fibers had diameters around 350 nm, and were soldered at most intersections, providing a strong dimensional stability to the mats. The nanofiber mats demonstrated very high conductivity (60 ± 10 S cm -1, the highest value reported so far for polymer nanofibers) as well as improved electrochemical properties, due to the ultraporous nature of the electrospun mats. The mats were incorporated into all-textile flexible supercapacitors, using carbon cloths as the current collectors and electrospun polyacrylonitrile (PAN) nanofibrous membranes as the separator. The textile layers were stacked and embedded in a solid electrolyte containing an ionic liquid and PVDF-co-HFP as the host polymer. The resulting supercapacitors were totally flexible and demonstrated interesting and stable performances in ambient conditions.

  7. Slowing down DNA translocation by a nanofiber meshed layer

    Science.gov (United States)

    Zhao, Yue; Xie, Wanyi; Tian, Enling; Ren, Yiwei; Zhu, Jifeng; Deng, Yunsheng; He, Shixuan; Liang, Liyuan; Wang, Yunjiao; Zhou, Daming; Wang, Deqiang

    2018-01-01

    Due to the weak interaction between DNA molecules and the inner surface of nanopores, DNA translocation is very fast, just leaving a short current drop without sufficient information to recognise the nucleotide sequence in the strand. In this paper, we propose a nanopore-nanofiber mesh hybridized structure to decelerate DNA translocation speed. Experimental results reveal that due to hydrophobic interaction between the DNA fragments and the nanofibers, the DNA moving speed can be retarded to two orders of magnitude slower. Furthermore, according to theory simulations, the additional fiber layer will reduce the electric field in the channel but elongate the capture region at the pore orifice, which will be helpful for increasing the capture rate and extending the DNA dwelling time in the meanwhile.

  8. Electrospun PBLG/PLA nanofiber membrane for constructing in vitro 3D model of melanoma.

    Science.gov (United States)

    Wang, Yaping; Qian, Junmin; Liu, Ting; Xu, Weijun; Zhao, Na; Suo, Aili

    2017-07-01

    Though much progress in utilizing tissue engineering technology to investigate tumor development in vitro has been made, the effective management of human melanoma is still a challenge in clinic due to lack of suitable 3D culture systems. In this study, we prepared a poly(γ-benzyl-l-glutamate)/poly(lactic acid) (PBLG/PLA) nanofiber membrane by electrospinning and demonstrated its suitability as a matrix for 3D culture of melanoma cells in vitro. The electrospun PBLG/PLA nanofiber membrane displayed a smooth and uniform fibrous morphology and had a desirable water contact angle of 79.3±0.6°. The average diameter of PBLG/PLA nanofibers was 320.3±95.1nm that was less than that (516.2±163.3nm) of pure PLA nanofibers. The addition of PBLG into PLA decreased the cold crystallization peak of PLA fibers from 93 to 75°C. The in vitro biocompatibility of PBLG/PLA nanofiber membrane was evaluated with B16F10 cells using PLA nanofiber membrane as control. It was found that, compared to PLA nanofiber membrane, PBLG/PLA nanofiber membrane could better support cell viability and proliferation, as indicated by MTT assay and live-dead staining. SEM results revealed that PBLG/PLA rather than PLA nanofiber membrane promoted the generation of tumoroid-like structures. These findings clearly demonstrated that the electrospun PBLG/PLA nanofiber membrane could mimick the extracellular matrix of melanoma microenvironment and be a promising platform for 3D cell culture. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Double emulsion electrospun nanofibers as a growth factor delivery vehicle for salivary gland regeneration

    Science.gov (United States)

    Foraida, Zahraa I.; Sharikova, Anna; Peerzada, Lubna N.; Khmaladze, Alexander; Larsen, Melinda; Castracane, James

    2017-08-01

    Sustained delivery of growth factors, proteins, drugs and other biologically active molecules is necessary for tissue engineering applications. Electrospun fibers are attractive tissue engineering scaffolds as they partially mimic the topography of the extracellular matrix (ECM). However, they do not provide continuous nourishment to the tissue. In search of a biomimetic scaffold for salivary gland tissue regeneration, we previously developed a blend nanofiber scaffold composed of the protein elastin and the synthetic polymer polylactic-co-glycolic acid (PLGA). The nanofiber scaffold promoted in vivo-like salivary epithelial cell tissue organization and apicobasal polarization. However, in order to enhance the salivary cell proliferation and biomimetic character of the scaffold, sustained growth factor delivery is needed. The composite nanofiber scaffold was optimized to act as a growth factor delivery system using epidermal growth factor (EGF) as a model protein. The nanofiber/EGF hybrid nanofibers were synthesized by double emulsion electrospinning where EGF is emulsified within a water/oil/water (w/o/w) double emulsion system. Successful incorporation of EGF was confirmed using Raman spectroscopy. EGF release profile was characterized using enzyme-linked immunosorbent assay (ELIZA) of the EGF content. Double emulsion electrospinning resulted in slower release of EGF. We demonstrated the potential of the proposed double emulsion electrospun nanofiber scaffold for the delivery of growth factors and/or drugs for tissue engineering and pharmaceutical applications.

  10. Mechanical properties and cellular response of novel electrospun nanofibers for ligament tissue engineering: Effects of orientation and geometry.

    Science.gov (United States)

    Pauly, Hannah M; Kelly, Daniel J; Popat, Ketul C; Trujillo, Nathan A; Dunne, Nicholas J; McCarthy, Helen O; Haut Donahue, Tammy L

    2016-08-01

    Electrospun nanofibers are a promising material for ligamentous tissue engineering, however weak mechanical properties of fibers to date have limited their clinical usage. The goal of this work was to modify electrospun nanofibers to create a robust structure that mimics the complex hierarchy of native tendons and ligaments. The scaffolds that were fabricated in this study consisted of either random or aligned nanofibers in flat sheets or rolled nanofiber bundles that mimic the size scale of fascicle units in primarily tensile load bearing soft musculoskeletal tissues. Altering nanofiber orientation and geometry significantly affected mechanical properties; most notably aligned nanofiber sheets had the greatest modulus; 125% higher than that of random nanofiber sheets; and 45% higher than aligned nanofiber bundles. Modifying aligned nanofiber sheets to form aligned nanofiber bundles also resulted in approximately 107% higher yield stresses and 140% higher yield strains. The mechanical properties of aligned nanofiber bundles were in the range of the mechanical properties of the native ACL: modulus=158±32MPa, yield stress=57±23MPa and yield strain=0.38±0.08. Adipose derived stem cells cultured on all surfaces remained viable and proliferated extensively over a 7 day culture period and cells elongated on nanofiber bundles. The results of the study suggest that aligned nanofiber bundles may be useful for ligament and tendon tissue engineering based on their mechanical properties and ability to support cell adhesion, proliferation, and elongation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Preparation of MnO nanofibers by novel hydrothermal treatment of manganese acetate/PVA electrospun nanofiber mats

    International Nuclear Information System (INIS)

    Barakat, Nasser A.M.; Park, Soo Jin; Khil, Myung Seob; Kim, Hak Yong

    2009-01-01

    In the present study, manganese monoxide (MnO) which is hard to prepare because of the chemical activity of the manganese metal has been synthesized in nanofibrous form. An electrospun manganese acetate/poly(vinyl alcohol) nanofiber mats have been hydrothermally treated by novel strategy. The treatment process was based on producing of water gas (Co and H 2 ) to eliminate the polymer and reduced the manganese acetate to manganese monoxide. The process was carried out by heating the dried nanofiber mates at 400 deg. C for 3 h in an especial designed reactor in which a stream of water vapor was passing through a bed of an activated carbon. The obtained physiochemical characterization results indicated that the proposed hydrothermal treatment process does have the ability to produce pure MnO nanofibers with good crystallinity.

  12. Graphene oxide decorated electrospun gelatin nanofibers: Fabrication, properties and applications

    Energy Technology Data Exchange (ETDEWEB)

    Jalaja, K. [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram, Kerala 695 547 (India); Sreehari, V.S. [Indian Institute of Science Education and Research Bhopal, Bhauri, Madhya Pradesh 462066 (India); Kumar, P.R. Anil [Tissue culture laboratory, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram, Kerala 695 012 (India); Nirmala, R. James, E-mail: nirmala@iist.ac.in [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram, Kerala 695 547 (India)

    2016-07-01

    Gelatin nanofiber fabricated by electrospinning process is found to mimic the complex structural and functional properties of natural extracellular matrix for tissue regeneration. In order to improve the physico-chemical and biological properties of the nanofibers, graphene oxide is incorporated in the gelatin to form graphene oxide decorated gelatin nanofibers. The current research effort is focussed on the fabrication and evaluation of physico-chemical and biological properties of graphene oxide-gelatin composite nanofibers. The presence of graphene oxide in the nanofibers was established by transmission electron microscopy (TEM). We report the effect of incorporation of graphene oxide on the mechanical, thermal and biological performance of the gelatin nanofibers. The tensile strength of gelatin nanofibers was increased from 8.29 ± 0.53 MPa to 21 ± 2.03 MPa after the incorporation of GO. In order to improve the water resistance of nanofibers, natural based cross-linking agent, namely, dextran aldehyde was employed. The cross-linked composite nanofibers showed further increase in the tensile strength up to 56.4 ± 2.03 MPa. Graphene oxide incorporated gelatin nanofibers are evaluated for bacterial activity against gram positive (Staphylococcus aureus) and gram negative (Escherichia coli) bacteria and cyto compatibility using mouse fibroblast cells (L-929 cells). The results indicate that the graphene oxide incorporated gelatin nanofibers do not prevent bacterial growth, nevertheless support the L-929 cell adhesion and proliferation. - Highlights: • Graphene oxide nano reinforced gelatin nanofibers are fabricated by electrospinning. • Graphene oxide (0.5%) loading resulted in increased tensile strength. • GO/gelatin nanofibers are cross-linked with dextran aldehyde. • Composite nanofibers favoured adhesion of L-929 cells. • GO/gelatin mats do not prevent bacterial growth.

  13. Electrospun polyacrylonitrile nanofibers loaded with silver nanoparticles by silver mirror reaction

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Yongzheng; Li, Yajing; Zhang, Jianfeng; Yu, Zhongzhen; Yang, Dongzhi, E-mail: yangdz@mail.buct.edu.cn

    2015-06-01

    The silver mirror reaction (SMR) method was selected in this paper to modify electrospun polyacrylonitrile (PAN) nanofibers, and these nanofibers loaded with silver nanoparticles showed excellent antibacterial properties. PAN nanofibers were first pretreated in AgNO{sub 3} aqueous solution before the SMR process so that the silver nanoparticles were distributed evenly on the outer surface of the nanofibers. The final PAN nanofibers were characterized by scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), transmission electron microscopy (TEM), TEM-selected area electron diffraction (SAED), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). SEM, TEM micrographs and SAED patterns confirmed homogeneous dispersion of the silver nanoparticles which were composed of monocrystals with diameters 20–30 nm. EDS and XRD results showed that these monocrystals tended to form face-centered cubic single silver. TGA test indicated that the nanoparticles loaded on the nanofibers reached above 50 wt.%. This material was also evaluated by the viable cell-counting method. The results indicated that PAN nanofibers loaded with silver nanoparticles exhibited excellent antimicrobial activities against gram-negative Escherichia coli (E. coli), gram-positive Staphylococcus aureus (S. aureus) and the fungus Monilia albicans. Thus, this material had many potential applications in biomedical fields. - Highlights: • Silver mirror reaction was used to prepare nanofibers loaded with silver nanoparticles. • The SAED patterns demonstrated the monocrystallinity of silver nanocrystals. • The XRD results showed nanoparticles tended to be face-centered cubic single silver. • The material showed excellent antimicrobial activities against bacteria and fungi.

  14. Synthesis and Characterization of Electrospun Nanocomposite TiO Nanofibers with Ag Nanoparticles for Photocatalysis Applications

    Directory of Open Access Journals (Sweden)

    Srujan Mishra

    2012-01-01

    Full Text Available Polycrystalline mixed-phase TiO2 nanofibers embedded with 2.0% w/v Ag nanoparticles was prepared by the electrospinning technique. Calcination of dry Ag nanoparticles-titanium (IV isopropoxide/PVP electrospun nanofiber mats in air at 510∘C for 24 h yielded polycrystalline TiO2/Ag nanofibers. The morphology and distribution of silver nanoparticles were observed by transmission electron microscopy (TEM, scanning TEM (STEM, and high-angle annular dark-field (HAADF imaging. Mixed-phase anatase and rutile TiO2 nanofibers were produced with Ag nanoparticles. High-resolution TEM lattice-fringe measurements showed good agreement with Ag (111, anatase (101, and rutile (110 phases. The photocatalytic activity of TiO2/Ag nanofibers was compared to the photocatalytic activity of pure TiO2 nanofibers by studying the photodegradation of methyl red dye under UV light irradiation, in a photoreactor. UV-visible absorbance spectra showed that the rate of decay of the dye in case of photodegradation by TiO2/Ag nanofibers was 10.3 times higher than that by pure TiO2 nanofibers. The retaining of the fiber morphology along with the increased surface area due to the addition of Ag nanoparticles can be believed to enhance the photocatalytic oxidation of methyl red dye.

  15. Assessment of Morphology, Activity, and Infiltration of Astrocytes on Marine EPS-Imbedded Electrospun PCL Nanofiber

    Directory of Open Access Journals (Sweden)

    Seul Ki Min

    2014-01-01

    Full Text Available Tissue engineering using a biomaterial including bioactive compounds has been researched as a way to restore injured neural systems. Extracellular polymeric substances (EPS extracted from marine seaweeds have been known to produce positive effects on physiological activities in human tissues. In this study, an electrospun nanofiber containing brown seaweed EPS was proven to be a candidate biomaterial for neural tissue engineering. Glial fibrillary acidic protein (GFAP as a specific marker protein increased in the astrocytes cultured on the polycaprolactone (PCL nanofiber containing EPS (EPS-PCL nanofiber, compared with PCL nanofiber. The upregulation of GFAP indicates that the EPS-PCL nanofiber induced astrocyte activation, which supports physiological agents favorable to restore injured neural tissue. Astrocytes could infiltrate into the EPS-PCL nanofiber mat without toxicity, comparable to PCL nanofiber. These results imply that EPS-PCL nanofiber could be a useful biomaterial to regulate astrocyte activity at a molecular level and could be considered as a novel therapeutic material for neural tissue engineering.

  16. Effects of Electrode Reversal on the Distribution of Naproxen in the Electrospun Cellulose Acetate Nanofibers

    Directory of Open Access Journals (Sweden)

    Zhuang Li

    2014-01-01

    Full Text Available Naproxen (NAP/cellulose acetate hybrid nanofibers were prepared by positive and reversed emitting electrodes electrospinning setups. The morphology and structure of the resultant nanofibers were characterized, and the NAP release behaviors were investigated. It was found that NAP dispersed in the CA matrix in molecular level, and no aggregation and dimers of NAP were found in the resultant NAP/CA hybrid nanofibers due to the formation of hydrogen bonds between NAP and CA. The nanofibers obtained by reversed emitting electrode electrospinning setup have a thicker diameter and a faster NAP release rate compared with those obtained by positive emitting electrode electrospinning setup. The faster drug release of NAP from nanofibers prepared by reversed emitting electrode electrospinning is due to the fact that the concentration of NAP molecules near the surface of the nanofibers is relatively higher than that of the nanofibers prepared by positive emitting electrode electrospinning setup. The effects of the electrode polarity on the distribution of drugs in nanofibers can be used to prepare hybrid electrospun fibers of different drug release rates, which may found applications in biomedical materials.

  17. Macroporous conductive polymer films fabricated by electrospun nanofiber templates and their electromechanical properties

    International Nuclear Information System (INIS)

    Zhou Jian; Gao Qiang; Fukawa, Tadashi; Shirai, Hirofusa; Kimura, Mutsumi

    2011-01-01

    We demonstrate a facile method to fabricate macroporous poly (3,4-ethylenedioxythiophene)/poly (4-styrene sulfonate) (PEDOT/PSS) films with empty channels by using electrospun nanofiber as a sacrificial template. The channels within the PEDOT/PSS films were prepared by depositing PEDOT/PSS aqueous dispersion onto poly (vinyl pyrrolidone)/poly(methyl methacrylate) (PVP/PMMA) nanofiber template, and then the nanofibers were removed by solvent extraction. The average diameter of the channels is 313 ± 45 nm, which is almost the same as the parent PVP/PMMA nanofibers. The macroporous PEDOT/PSS film with the empty channels showed an enhancement of electromechanical properties compared to the nonporous PEDOT/PSS film.

  18. Electrospun nanofiber-based thermite textiles and their reactive properties.

    Science.gov (United States)

    Yan, Shi; Jian, Guoqiang; Zachariah, Michael R

    2012-12-01

    In this work, we present a first time fabrication of thermite-based nanofiber mats with a nitrocellulose composite energetic binder to create a new class of energetic 1D nanocomposite. The as prepared thermite based nanofibrous mats were characterized and tested for their burning behavior, and compared with the pure nitrocellulose and nanoaluminum incorporated nanofibers for their combustion performances. Thermite-based nanofibers show enhanced burning rates in combustion tests, which correlate to the mass loading of nanothermite relative to binder in nanofibers. The electrospinning method demonstrates the possibility of avoiding some of the problems associated with melt casting nanometalized propellants.

  19. Application of a biotin functionalized QD assay for determining available binding sites on electrospun nanofiber membrane.

    Science.gov (United States)

    Marek, Patrick; Senecal, Kris; Nida, Dawn; Magnone, Joshua; Senecal, Andre

    2011-10-24

    The quantification of surface groups attached to non-woven fibers is an important step in developing nanofiber biosensing detection technologies. A method utilizing biotin functionalized quantum dots (QDs) 655 for quantitative analysis of available biotin binding sites within avidin immobilized on electrospun nanofiber membranes was developed. A method for quantifying nanofiber bound avidin using biotin functionalized QDs is presented. Avidin was covalently bound to electrospun fibrous polyvinyl chloride (PVC 1.8% COOH w/w containing 10% w/w carbon black) membranes using primary amine reactive EDC-Sulfo NHS linkage chemistry. After a 12 h exposure of the avidin coated membranes to the biotin-QD complex, fluorescence intensity was measured and the total amount of attached QDs was determined from a standard curve of QD in solution (total fluorescence vs. femtomole of QD 655). Additionally, fluorescence confocal microscopy verified the labeling of avidin coated nanofibers with QDs. The developed method was tested against 2.4, 5.2, 7.3 and 13.7 mg spray weights of electrospun nanofiber mats. Of the spray weight samples tested, maximum fluorescence was measured for a weight of 7.3 mg, not at the highest weight of 13.7 mg. The data of total fluorescence from QDs bound to immobilized avidin on increasing weights of nanofiber membrane was best fit with a second order polynomial equation (R(2) = .9973) while the standard curve of total fluorescence vs. femtomole QDs in solution had a linear response (R(2) = .999). A QD assay was developed in this study that provides a direct method for quantifying ligand attachment sites of avidin covalently bound to surfaces. The strong fluorescence signal that is a fundamental characteristic of QDs allows for the measurement of small changes in the amount of these particles in solution or attached to surfaces.

  20. Application of a biotin functionalized QD assay for determining available binding sites on electrospun nanofiber membrane

    Directory of Open Access Journals (Sweden)

    Magnone Joshua

    2011-10-01

    Full Text Available Abstract Background The quantification of surface groups attached to non-woven fibers is an important step in developing nanofiber biosensing detection technologies. A method utilizing biotin functionalized quantum dots (QDs 655 for quantitative analysis of available biotin binding sites within avidin immobilized on electrospun nanofiber membranes was developed. Results A method for quantifying nanofiber bound avidin using biotin functionalized QDs is presented. Avidin was covalently bound to electrospun fibrous polyvinyl chloride (PVC 1.8% COOH w/w containing 10% w/w carbon black membranes using primary amine reactive EDC-Sulfo NHS linkage chemistry. After a 12 h exposure of the avidin coated membranes to the biotin-QD complex, fluorescence intensity was measured and the total amount of attached QDs was determined from a standard curve of QD in solution (total fluorescence vs. femtomole of QD 655. Additionally, fluorescence confocal microscopy verified the labeling of avidin coated nanofibers with QDs. The developed method was tested against 2.4, 5.2, 7.3 and 13.7 mg spray weights of electrospun nanofiber mats. Of the spray weight samples tested, maximum fluorescence was measured for a weight of 7.3 mg, not at the highest weight of 13.7 mg. The data of total fluorescence from QDs bound to immobilized avidin on increasing weights of nanofiber membrane was best fit with a second order polynomial equation (R2 = .9973 while the standard curve of total fluorescence vs. femtomole QDs in solution had a linear response (R2 = .999. Conclusion A QD assay was developed in this study that provides a direct method for quantifying ligand attachment sites of avidin covalently bound to surfaces. The strong fluorescence signal that is a fundamental characteristic of QDs allows for the measurement of small changes in the amount of these particles in solution or attached to surfaces.

  1. Electrospun Nanofibers of Guar Galactomannan for Targeted Drug Delivery

    Science.gov (United States)

    Chu, Hsiao Mei Annie

    2011-12-01

    Guar galactomannan is a biodegradable polysaccharide used widely in the food industry but also in the cosmetics, pharmaceutical, oil drilling, textile and paper industries. Guar consists of a mannose backbone and galactose side groups that are both susceptible to enzyme degradation, a unique property that can be explored for targeted drug delivery especially since those enzymes are naturally secreted by the microflora in human colon. The present study can be divided into three parts. In the first part, we discuss ways to modify guar to produce nanofibers by electrospinning, a process that involves the application of an electric field to a polymer solution or melt to facilitate production of fibers in the sub-micron range. Nanofibers are currently being explored as the next generation of drug carriers due to its many advantages, none more important than the fact that nanofibers are on a size scale that is a fraction of a hair's width and have large surface-to-volume ratio. The incorporation and controlled release of nano-sized drugs is one way in which nanofibers are being utilized in drug delivery. In the second part of the study, we explore various methods to crosslink guar nanofibers as a means to promote water-resistance in a potential drug carrier. The scope and utility of water-resistant guar nanofibers can only be fully appreciated when subsequent drug release studies are carried out. To that end, the third part of our study focuses on understanding the kinetics and diffusion mechanisms of a model drug, Rhodamine B, through moderately-swelling (crosslinked) hydrogel nanofibers in comparison to rapidly-swelling (non-crosslinked) nanofibers. Along the way, our investigations led us to a novel electrospinning set-up that has a unique collector designed to capture aligned nanofibers. These aligned nanofiber bundles can then be twisted to hold them together like yarn. From a practical standpoint, these yarns are advantageous because they come freely suspended and

  2. Assembling of electrospun meshes into three-dimensional porous scaffolds for bone repair.

    Science.gov (United States)

    Song, Juqing; Zhu, Guanglin; Wang, Lin; An, Geng; Shi, Xuetao; Wang, Yingjun

    2017-02-14

    Technical limitations of traditional electrospinning make it hard to produce three-dimensional (3D) scaffolds with hierarchical pore structures. Here, porous polycaprolactone (PCL) nanofiber meshes with different nano-hydroxyapatite (nHA) concentrations were prepared by electrospinning with stainless steel mesh as the collector, and 3D porous nanofiber scaffolds were fabricated via layer-by-layer assembly with a special binder (18% PCL/DCM solution). The single layer nanofiber mesh possessed very regular morphology with a hollow structure, and the nHA was not only embedded in the nanofiber but also exposed on the surfaces of the fiber, resulting in the improved surface chemical properties. The incorporation of nHA also had a significant effect on cell behaviours and functions. The 3D nanofiber scaffolds possessed hierarchical structures with interconnected micro and macro pores, which allowed cells to migrate between the adjacent layers, even throughout the scaffold. Cells filled the scaffold space and integrated with the nanofiber materials, forming scaffold/cells complexes in vitro. In addition, alendronate was successfully carried on the 3D composite scaffolds because of the high affinity of P-C-P backbone to calcium ions. The composite scaffolds treated with alendronate significantly promote the osteogenesis-related gene expression of human foetal osteoblasts. All these results suggest that 3D functional nanofiber scaffolds would be potentially useful for bone repair.

  3. Electrospun polyacrylonitrile nanofibers loaded with silver nanoparticles by silver mirror reaction.

    Science.gov (United States)

    Shi, Yongzheng; Li, Yajing; Zhang, Jianfeng; Yu, Zhongzhen; Yang, Dongzhi

    2015-06-01

    The silver mirror reaction (SMR) method was selected in this paper to modify electrospun polyacrylonitrile (PAN) nanofibers, and these nanofibers loaded with silver nanoparticles showed excellent antibacterial properties. PAN nanofibers were first pretreated in AgNO3 aqueous solution before the SMR process so that the silver nanoparticles were distributed evenly on the outer surface of the nanofibers. The final PAN nanofibers were characterized by scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), transmission electron microscopy (TEM), TEM-selected area electron diffraction (SAED), X-ray diffraction (XRD) and thermogravimetric analysis (TGA). SEM, TEM micrographs and SAED patterns confirmed homogeneous dispersion of the silver nanoparticles which were composed of monocrystals with diameters 20-30nm. EDS and XRD results showed that these monocrystals tended to form face-centered cubic single silver. TGA test indicated that the nanoparticles loaded on the nanofibers reached above 50wt.%. This material was also evaluated by the viable cell-counting method. The results indicated that PAN nanofibers loaded with silver nanoparticles exhibited excellent antimicrobial activities against gram-negative Escherichia coli (E. coli), gram-positive Staphylococcus aureus (S. aureus) and the fungus Monilia albicans. Thus, this material had many potential applications in biomedical fields. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Electrospun polyacrylonitrile nanofibers functionalized with EDTA for adsorption of ionic dyes

    Science.gov (United States)

    Chaúque, Eutilério F. C.; Dlamini, Langelihle N.; Adelodun, Adedeji A.; Greyling, Corinne J.; Ngila, J. Catherine

    2017-08-01

    The manipulation of nanofibers' surface chemistry could enhance their potential application toward the removal of ionic dyes in wastewater. For this purpose, surface modification of electrospun polyacrylonitrile (PAN) nanofibers with ethylenediaminetetraacetic acid (EDTA) and ethylenediamine (EDA) crosslinker was experimented. The functionalized EDTA-EDA-PAN nanofibers were characterized using Fourier transform infrared (FT-IR) spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) technique. The impregnation of EDA and EDTA chelating agents on the surface of PAN changed the distribution of nanofibers as proximity is increased (accompanied by reduced softness), but the nanofibrous structure of the pristine PAN nanofibers was not substantially altered. Adsorption equilibrium studies were performed with Freundlich, Langmuir and Temkin isotherm models with the former providing better correlation to the experimental data. The modified PAN nanofibers showed efficient sorption of methyl orange (MO) and reactive red (RR) from aqueous synthetic samples, evinced by the maximum adsorption capacities (at 25 °C) of 99.15 and 110.0 mg g-1, respectively. The fabricated nanofibers showed appreciable removal efficiency of the target dye sorptives from wastewater. However, the presence of high metal ions content affected the overall extraction of dyes from wastewater due to the depletion of the adsorbent's active adsorptive sites.

  5. Oxolane-2,5-dione modified electrospun cellulose nanofibers for heavy metals adsorption

    International Nuclear Information System (INIS)

    Stephen, Musyoka; Catherine, Ngila; Brenda, Moodley; Andrew, Kindness; Leslie, Petrik; Corrine, Greyling

    2011-01-01

    Highlights: → Electrospun and modified cellulose nanofibers have high surface area. → Modified nanofibers showed improved adsorption of Cd and Pb from water. → Regenerated modified nanofibers had high adsorption capacity hence recyclable. - Abstract: Functionalized cellulose nanofibers have been obtained through electrospinning and modification with oxolane-2,5-dione. The application of the nanofibers for adsorption of cadmium and lead ions from model wastewater samples is presented for the first time. Physical and chemical properties of the nanofibers were characterized. Surface chemistry during preparation and functionalization was monitored using Fourier transform-infrared spectroscopy, scanning electron microscopy, carbon-13 solid state nuclear magnetic resonance spectroscopy and Brunauer Emmett and Teller. Enhanced surface area of 13.68 m 2 g -1 was recorded for the nanofibers as compared to the cellulose fibers with a surface area of 3.22 m 2 g -1 . Freundlich isotherm was found to describe the interactions better than Langmuir: K f = 1.0 and 2.91 mmol g -1 (r 2 = 0.997 and 0.988) for lead and cadmium, respectively. Regenerability of the fiber mats was investigated and the results obtained indicate sustainability in adsorption efficacy of the material.

  6. A novel fixed-bed reactor design incorporating an electrospun PVA/chitosan nanofiber membrane

    International Nuclear Information System (INIS)

    Esmaeili, Akbar; Beni, Ali Aghababai

    2014-01-01

    Graphical abstract: PVA/Cs nanofiber membrane was prepared by the electrospinning technique. The membrane was installed in a new fixed-bed reactor. The test results showed heavy metals absorbed by the PVA/Cs nanofiber membrane. - Highlights: • PVA/Cs nano-fiber membrane was produced using electrospinning technique. • The prepared nanofiber membrane was mesoporous. • Thermal crosslinking was successful to improve the stability of PVA/Cs nano-fiber membrane. • Experimental data were studied by adsorption isotherm models and thermodynamic relationships. - Abstract: In this research, a novel fixed-bed reactor was designed with a nanofiber membrane composed of a polyvinyl alcohol (PVA)/chitosan nanofiber blend prepared using an electrospinning technique. The applied voltage, tip-collector distance, and solution flow rate of the electrospinning process were 18 kV, 14.5 cm, and 0.5 mL h −1 , respectively. Brunauer–Emmett–Teller (BET) theory, scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR) were employed to characterize and analyze the nanofiber membranes. Homogeneous electrospun nanofibers with an average diameter of 99.47 nm and surface area of 214.12 m 2 g −1 were obtained. Adsorption experiments were carried out in a batch system to investigate the effect of different adsorption parameters such as pH, adsorbent dose, biomass dose, contact time, and temperature. The kinetic data, obtained at the optimal pH of 6, were analyzed by pseudo first-order and pseudo second-order kinetic models. Three isotherm models and thermodynamic parameters (ΔG°, ΔH°, and ΔS°) were applied to describe the equilibrium data of the metal ions adsorbed onto the PVA/chitosan nanofiber membrane

  7. Mechanically-reinforced electrospun composite silk fibroin nanofibers containing hydroxyapatite nanoparticles

    International Nuclear Information System (INIS)

    Kim, Hyunryung; Che, Lihua; Ha, Yoon; Ryu, WonHyoung

    2014-01-01

    Electrospun silk fibroin (SF) scaffolds provide large surface area, high porosity, and interconnection for cell adhesion and proliferation and they may replace collagen for many tissue engineering applications. Despite such advantages, electrospun SF scaffolds are still limited as bone tissue replacement due to their low mechanical strengths. While enhancement of mechanical strengths by incorporating inorganic ceramics into polymers has been demonstrated, electrospinning of a mixture of SF and inorganic ceramics such as hydroxyapatite is challenging and less studied due to the aggregation of ceramic particles within SF. In this study, we aimed to enhance the mechanical properties of electrospun SF scaffolds by uniformly dispersing hydroxyapatite (HAp) nanoparticles within SF nanofibers. HAp nanoaprticles were modified by γ-glycidoxypropyltrimethoxysilane (GPTMS) for uniform dispersion and enhanced interfacial bonding between HAp and SF fibers. Optimal conditions for electrospinning of SF and GPTMS-modified HAp nanoparticles were identified to achieve beadless nanofibers without any aggregation of HAp nanoparticles. The MTT and SEM analysis of the osteoblasts-cultured scaffolds confirmed the biocompatibility of the composite scaffolds. The mechanical properties of the composite scaffolds were analyzed by tensile tests for the scaffolds with varying contents of HAp within SF fibers. The mechanical testing showed the peak strengths at the HAp content of 20 wt.%. The increase of HAp content up to 20 wt.% increased the mechanical properties of the composite scaffolds, while further increase above 20 wt.% disrupted the polymer chain networks within SF nanofibers and weakened the mechanical strengths. - Highlights: • Electrospun composite silk fibroin scaffolds were mechanically-reinforced. • GPTMS enhanced hydroxyapatite distribution in silk fibroin nanofibers. • Mechanical property of composite scaffolds increased up to 20% of hydroxyapatite. • Composite

  8. Electrospun tilapia collagen nanofibers accelerating wound healing via inducing keratinocytes proliferation and differentiation.

    Science.gov (United States)

    Zhou, Tian; Wang, Nanping; Xue, Yang; Ding, Tingting; Liu, Xin; Mo, Xiumei; Sun, Jiao

    2016-07-01

    The development of biomaterials with the ability to induce skin wound healing is a great challenge in biomedicine. In this study, tilapia skin collagen sponge and electrospun nanofibers were developed for wound dressing. The collagen sponge was composed of at least two α-peptides. It did not change the number of spleen-derived lymphocytes in BALB/c mice, the ratio of CD4(+)/CD8(+) lymphocytes, and the level of IgG or IgM in Sprague-Dawley rats. The tensile strength and contact angle of collagen nanofibers were 6.72±0.44MPa and 26.71±4.88°, respectively. They also had good thermal stability and swelling property. Furthermore, the nanofibers could significantly promote the proliferation of human keratinocytes (HaCaTs) and stimulate epidermal differentiation through the up-regulated gene expression of involucrin, filaggrin, and type I transglutaminase in HaCaTs. The collagen nanofibers could also facilitate rat skin regeneration. In the present study, electrospun biomimetic tilapia skin collagen nanofibers were succesfully prepared, were proved to have good bioactivity and could accelerate rat wound healing rapidly and effectively. These biological effects might be attributed to the biomimic extracellular matrix structure and the multiple amino acids of the collagen nanofibers. Therefore, the cost-efficient tilapia collagen nanofibers could be used as novel wound dressing, meanwhile effectively avoiding the risk of transmitting animal disease in the future clinical apllication. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Thermal, Electrical and Surface Hydrophobic Properties of Electrospun Polyacrylonitrile Nanofibers for Structural Health Monitoring.

    Science.gov (United States)

    Alarifi, Ibrahim M; Alharbi, Abdulaziz; Khan, Waseem S; Swindle, Andrew; Asmatulu, Ramazan

    2015-10-14

    This paper presents an idea of using carbonized electrospun Polyacrylonitrile (PAN) fibers as a sensor material in a structural health monitoring (SHM) system. The electrospun PAN fibers are lightweight, less costly and do not interfere with the functioning of infrastructure. This study deals with the fabrication of PAN-based nanofibers via electrospinning followed by stabilization and carbonization in order to remove all non-carbonaceous material and ensure pure carbon fibers as the resulting material. Electrochemical impedance spectroscopy was used to determine the ionic conductivity of PAN fibers. The X-ray diffraction study showed that the repeated peaks near 42° on the activated nanofiber film were α and β phases, respectively, with crystalline forms. Contact angle, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) were also employed to examine the surface, thermal and chemical properties of the carbonized electrospun PAN fibers. The test results indicated that the carbonized PAN nanofibers have superior physical properties, which may be useful for structural health monitoring (SHM) applications in different industries.

  10. Evaluation of the Morphology and Osteogenic Potential of Titania-Based Electrospun Nanofibers

    Directory of Open Access Journals (Sweden)

    Xiaokun Wang

    2012-01-01

    Full Text Available Submicron-scale titania-based ceramic fibers with various compositions have been prepared by electrospinning. The as-prepared nanofibers were heat-treated at 700°C for 3 h to obtain pure inorganic fiber meshes. The results show that the diameter and morphology of the nanofibers are affected by starting polymer concentration and sol-gel composition. The titania and titania-silica nanofibers had the average diameter about 100–300 nm. The crystal phase varied from high-crystallized rutile-anatase mixed crystal to low-crystallized anatase with adding the silica addition. The morphology and crystal phase were evaluated by SEM and XRD. Bone-marrow-derived mesenchymal stem cells were seeded on titania-silica 50/50 fiber meshes. Cell number and early differentiation marker expressions were analyzed, and the results indicated osteogenic potential of the titania-silica 50/50 fiber meshes.

  11. Lithography-free centimeter-long nanochannel fabrication method using an electrospun nanofiber array

    International Nuclear Information System (INIS)

    Park, Suk Hee; Shin, Hyun-Jun; Lee, Sangyoup; Kim, Yong-Hwan; Yang, Dong-Yol; Lee, Jong-Chul

    2012-01-01

    Novel cost-effective methods for polymeric and metallic nanochannel fabrication have been demonstrated using an electrospun nanofiber array. Like other electrospun nanofiber-based nanofabrication methods, our system also showed high throughput as well as cost-effective performances. Unlike other systems, however, our fabrication scheme provides a pseudo-parallel nanofiber array a few centimeters long at a speed of several tens of fibers per second based on our unique inclined-gap fiber collecting system. Pseudo-parallel nanofiber arrays were used either directly for the PDMS molding process or for the metal lift-off process followed by the SiO 2 deposition process to produce the nanochannel array. While the PDMS molding process was a simple fabrication based on one-step casting, the metal lift-off process followed by SiO 2 deposition allowed finetuning on height and width of nanogrooves down to subhundred nanometers from a few micrometers. Nanogrooves were covered either with cover glass or with PDMS slab and nanochannel connectivity was investigated with a fluorescent dye. Also, nanochannel arrays were used to investigate mobility and conformations of λ-DNA. (paper)

  12. Electrospun carbon nanofibers for improved electrical conductivity of fiber reinforced composites

    Science.gov (United States)

    Alarifi, Ibrahim M.; Alharbi, Abdulaziz; Khan, Waseem S.; Asmatulu, Ramazan

    2015-04-01

    Polyacrylonitrile (PAN) was dissolved in dimethylformamide (DMF), and then electrospun to generate nanofibers using various electrospinning conditions, such as pump speeds, DC voltages and tip-to-collector distances. The produced nanofibers were oxidized at 270 °C for 1 hr, and then carbonized at 850 °C in an argon gas for additional 1 hr. The resultant carbonized PAN nanofibers were placed on top of the pre-preg carbon fiber composites as top layers prior to the vacuum oven curing following the pre-preg composite curing procedures. The major purpose of this study is to determine if the carbonized nanofibers on the fiber reinforced composites can detect the structural defects on the composite, which may be useful for the structural health monitoring (SHM) of the composites. Scanning electron microscopy images showed that the electrospun PAN fibers were well integrated on the pre-preg composites. Electrical conductivity studies under various tensile loads revealed that nanoscale carbon fibers on the fiber reinforced composites detected small changes of loads by changing the resistance values. Electrically conductive composite manufacturing can have huge benefits over the conventional composites primarily used for the military and civilian aircraft and wind turbine blades.

  13. A review on electrospun nanofibers for oral drug delivery

    OpenAIRE

    Abbas Akhgari; Zahra Shakib; Setareh Sanati

    2017-01-01

    Nowadays, polymer nanofibers have gained attention due to remarkable characteristics such as high porosity and large surface area to volume ratio. Among their fabrication methods, electrospinning technique has been attracted as a simple and reproducible approach. It is a versatile, simple and cost-effective technique for the production of continuous nanofibers with acceptable characteristics such as high porosity, high surface area to volume ratio, high loading capacity and encapsulation effi...

  14. Synthesis, microstructures, and magnetoelectric couplings of electrospun multiferroic nanofibers

    Science.gov (United States)

    Xie, Shu-Hong; Liu, Yun-Ya; Li, Jiang-Yu

    2012-08-01

    Multiferroic materials with two or more types of ferroic orders have attracted a great deal of attention in the last decade for their magnetoelectric coupling, and new ideas and concepts have been explored recently to develop multiferroic materials at nano-scale. Motivated by theoretical analysis, we synthesized single-phase BiFeO3 (BFO) nanofibers, Pb(Zr0.52Ti0.48)O3-CoFe2O4 (PZT-CFO) and Pb(Zr0.52Ti0.48)O3-NiFe2O4 (PZT-NFO) composite nanofibers, and CoFe2O4-Pb(Zr0.52Ti0.48)O3 (CFO-PZT) core-shell nanofibers using sol-gel based electrospinning. These nanofibers typically have diameters in the range of a few hundred nanometers and grain size in the range of 10s nanometers, and exhibits both ferroelectric and ferromagnetic properties. Piezoresponse force microscopy (PFM) based techniques have also been developed to examine the magnetoelectric coupling of the nanofibers, which is estimated to be two orders of magnitude higher than that of thin films, consistent with our theoretical analysis. These nanofibers are promising for a variety of multiferroic applications.

  15. Fabrication of electrospun almond gum/PVA nanofibers as a thermostable delivery system for vanillin.

    Science.gov (United States)

    Rezaei, Atefe; Tavanai, Hossein; Nasirpour, Ali

    2016-10-01

    In this study, the fabrication of vanillin incorporated almond gum/polyvinyl alcohol (PVA) nanofibers through electrospinning has been investigated. Electrospinning of only almond gum was proved impossible. It was found that the aqueous solution of almond gum/PVA (80:20, concentration=7% (w/w)) containing 3% (w/w) vanillin could have successfully electrospun to uniform nanofibers with diameters as low as 77nm. According to the thermal analysis, incorporated vanillin in almond gum/PVA nanofibers showed higher thermal stability than free vanillin, making this composite especially suitable for high temperature applications. XRD and FTIR analyses proved the presence of vanillin in the almond gum/PVA nanofibers. It was also found that vanillin was dispersed as big crystallites in the matrix of almond gum/PVA nanofibers. FTIR analysis showed almond gum and PVA had chemical cross-linking by etheric bonds between COH groups of almond gum and OH groups of PVA. Also, in the nanofibers, there were no major interaction between vanillin and either almond gum or PVA. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Effects of O2 plasma treatment of PDMS on the deposition of electrospun PVA nanofibers

    Science.gov (United States)

    Kobayashi, Natsumi; Miki, Norihisa; Hishida, Koichi; Hotta, Atsushi

    2014-03-01

    A new polymeric nanofiber-alignment technique with the selective deposition of the nanofibers using oxygen (O2) plasma treatment on a base material for the electrospinning was introduced. Generally, without any pretreatments, electrospun fibers are deposited randomly on the collector. In this work, we focused on the O2 plasma treatment of the surface of the base material to modify the surface morphology and to add polar groups to the surface. O2 plasma-treated and untreated surface of poly (dimethylsiloxane) (PDMS) was prepared by masking a part of PDMS film by another PDMS film. The polyvinyl alcohol (PVA) fibers were then deposited onto the PDMS film. The surface structure of the PDMS film with PVA nanofibers was analyzed by scanning electron microscopy, water contact angle measurements, and X-ray photon spectroscopy. Only a few PVA nanofibers were deposited randomly on the untreated area of the PDMS film, while a number of PVA nanofibers were selectively deposited onto the O2 plasma-treated area. Intriguingly, PVA nanofibers were neatly aligned along the border of the untreated and the treated areas. The contact angle of the plasma-treated surface of PDMS decreased from 105 to 22 degree and the atomic ratio of O/Si was 1.7 times higher than that of the untreated PDMS.

  17. Electrospun decyl-3-methylimidazolium mono bromate/polyamide nanofibers as solid-phase microextraction coating.

    Science.gov (United States)

    Roostaie, Ali; Rastegar, Sorosh; Najarzadegan, Hamid; Ehteshami, Shokooh

    2017-09-22

    In the current study, electrospun-based ionic liquid (IL) doped polyamide (PA) nanofibers were prepared and used as the coating material of solid phase microextration device in the fiber geometry. Addition of IL, decyl-3-methylimidazolium mono bromate, increased the conductivity of the PA solution facilitating the electrospining process. The scanning electron microscopy images of decyl-3-methylimidazolium mono bromated/polyamide nanofibers showed the decreased diameter of the nanofibers in the range of 35-160nm compared to the PA nanofiber. The factors affecting the structure of nanofibers (e.g. ratio of decyl-3-methylimidazolium mono bromate to PA, coating time and applied voltage) were studied. In addition, influential parameters of extraction/desorption performance such as ionic strength, extraction time, and desorption time and temperature were studied. The limit of detections and limit of quantifications were obtained in the range of 0.75-0.9 and 2-5ngL -1 , respectively, demonstrating high efficiency of the prepared nanofiber. The developed method also showed good repeatability, RSD 4-9% (n=3), for the spiked aqueous solution at concentration level 150ngL -1 of chlorobenzenes, and linearity,R=0.996, in the range of 5-5000ngL -1 . Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Electrospun PCL/gelatin composite nanofiber structures for effective guided bone regeneration membranes.

    Science.gov (United States)

    Ren, Ke; Wang, Yi; Sun, Tao; Yue, Wen; Zhang, Hongyu

    2017-09-01

    Guided bone regeneration (GBR) membranes have been proved of great benefit for bone tissue engineering due to the improvement of cell attachment and proliferation. To develop GBR membranes with better biocompatibility and more proper degradation ability, here we fabricated polycaprolactone (PCL, polymer)/gelatin (protein) hybrid nanofibrous GBR membranes via electrospinning, followed by crosslinking with genipin. Acetic acid (HAc) was utilized to resolve the phase separation of PCL and gelatin, therefore homogeneous PCL/gelatin hybrid nanofibers with different ratios were successfully prepared. FTIR, XPS, TGA, DSC results proved that the proportion of PCL and gelatin in the as-spun nanofiber membranes could be simply adjusted by changing the weight ratio of PCL and gelatin in the spinning solution. SEM and AFM images demonstrated that all the nanofibers possessed uniform and smooth structures both in two dimension (2D) and three dimension (3D). The mechanical tests showed that these nanofibers exhibited appropriate tensile and strength properties, which were suitable for bone tissue engineering. CCK-8 and SEM images revealed that all the membranes were biocompatible to MC3T3-e1 cells. In addition, the in vitro osteogenesis characterizations, alizarin red in normal medium and osteogenesis medium, indicated that the nanofibers could promote bone formation. Therefore, all these results could suggest that our design of electrospun polymer/protein nanofiber membranes was effective for guided bone regeneration. Copyright © 2017. Published by Elsevier B.V.

  19. Improved efficiency of organic/inorganic photovoltaic devices by electrospun ZnO nanofibers

    International Nuclear Information System (INIS)

    Tanveer, Muhammad; Habib, Amir; Khan, Muhammad Bilal

    2012-01-01

    Highlights: ► Hybrid P3HT:PCBM/ZnO nanofibers photovoltaic devices with improved efficiency (2.23%). ► Improved open circuit voltage and fill factor. ► Studied the effect of electrospinning time to improve device performance. ► Such effect was not reported for Zno/P3HT:PCBM hybrid photovoltaic devices. ► Optimizing nanofiber mat thickness by optimum electrospinning time to allow maximum infiltration through the pores. - Abstract: The efficiency of the photovoltaic (PV) device based on P3HT and PCBM bulk heterojunction is improved by introducing small-diameter electrospun ZnO diffused nanofibers network. Diameter, diffusion and melting of nanofibers are controlled by calcination temperature. The thickness of the active layer is optimized for efficient PV devices by varying electrospinning (ES) time. Increased nanofiber's mat thickness by an increase in electrospinning time beyond a certain optimum value reduces the device performance due to increased series resistance, increased traps and reduced blend infiltration through the nanofiber pores. ES time suggests optimized active area for energy absorption and exciton dissociation. In this study, we report the improvement in power conversion efficiency (PCE) from 0.9% to 2.23%, for optimum ES time (∼300 s).

  20. Improved efficiency of organic/inorganic photovoltaic devices by electrospun ZnO nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Tanveer, Muhammad, E-mail: mtanveerp@gmail.com [School of Chemical and Materials Engineering, National University of Sciences and Technology, Islamabad 44000 (Pakistan); Habib, Amir [School of Chemical and Materials Engineering, National University of Sciences and Technology, Islamabad 44000 (Pakistan); Khan, Muhammad Bilal [Centre for Energy Systems, National University of Sciences and Technology, Islamabad 44000 (Pakistan)

    2012-08-01

    Highlights: Black-Right-Pointing-Pointer Hybrid P3HT:PCBM/ZnO nanofibers photovoltaic devices with improved efficiency (2.23%). Black-Right-Pointing-Pointer Improved open circuit voltage and fill factor. Black-Right-Pointing-Pointer Studied the effect of electrospinning time to improve device performance. Black-Right-Pointing-Pointer Such effect was not reported for Zno/P3HT:PCBM hybrid photovoltaic devices. Black-Right-Pointing-Pointer Optimizing nanofiber mat thickness by optimum electrospinning time to allow maximum infiltration through the pores. - Abstract: The efficiency of the photovoltaic (PV) device based on P3HT and PCBM bulk heterojunction is improved by introducing small-diameter electrospun ZnO diffused nanofibers network. Diameter, diffusion and melting of nanofibers are controlled by calcination temperature. The thickness of the active layer is optimized for efficient PV devices by varying electrospinning (ES) time. Increased nanofiber's mat thickness by an increase in electrospinning time beyond a certain optimum value reduces the device performance due to increased series resistance, increased traps and reduced blend infiltration through the nanofiber pores. ES time suggests optimized active area for energy absorption and exciton dissociation. In this study, we report the improvement in power conversion efficiency (PCE) from 0.9% to 2.23%, for optimum ES time ({approx}300 s).

  1. Electrospun Nanofiber Scaffolds and Their Hydrogel Composites for the Engineering and Regeneration of Soft Tissues.

    Science.gov (United States)

    Manoukian, Ohan S; Matta, Rita; Letendre, Justin; Collins, Paige; Mazzocca, Augustus D; Kumbar, Sangamesh G

    2017-01-01

    Electrospinning has emerged as a simple, elegant, and scalable technique that can be used to fabricate polymeric nanofibers. Pure polymers as well as blends and composites of both natural and synthetic ones have been successfully electrospun into nanofiber matrices for many biomedical applications. Tissue-engineered medical implants, such as polymeric nanofiber scaffolds, are potential alternatives to autografts and allografts, which are short in supply and carry risks of disease transmission. These scaffolds have been used to engineer various soft tissues, including connective tissues, such as skin, ligament, and tendon, as well as nonconnective ones, such as vascular, muscle, and neural tissue. Electrospun nanofiber matrices show morphological similarities to the natural extracellular matrix (ECM), characterized by ultrafine continuous fibers, high surface-to-volume ratios, high porosities, and variable pore-size distributions. The physiochemical properties of nanofiber matrices can be controlled by manipulating electrospinning parameters so that they meet the requirements of a specific application.Nanostructured implants show improved biological performance over bulk materials in aspects of cellular infiltration and in vivo integration, taking advantage of unique quantum, physical, and atomic properties. Furthermore, the topographies of such scaffolds has been shown to dictate cellular attachment, migration, proliferation, and differentiation, which are critical in engineering complex functional tissues with improved biocompatibility and functional performance. This chapter discusses the use of the electrospinning technique in the fabrication of polymer nanofiber scaffolds utilized for the regeneration of soft tissues. Selected scaffolds will be seeded with human mesenchymal stem cells (hMSCs), imaged using scanning electron and confocal microscopy, and then evaluated for their mechanical properties as well as their abilities to promote cell adhesion

  2. Tolnaftate-Loaded PolyacrylateElectrospun Nanofibers for an Impressive Regimen on Dermatophytosis

    Directory of Open Access Journals (Sweden)

    Shashi Kiran Misra

    2017-11-01

    Full Text Available Dermatophytosis, topical fungal infection is the most common cause of skin bug in the world, generally underestimated and ignored. It is commonly caused by immensely mortifying and keratinophilic fungal eukaryotes which invade keratinized tissues and generate different tinea diseases in Mediterranean countries. We herein fabricated nanofibers/scaffolds embedded with thiocarbamate derivative topical antifungal tolnaftatefor the first time to target the complete elimination of dermatophyte at the site of infection. In this regard, variable combinations of biocompatible Eudragit grades (ERL100 and ERS100 were selected to provide better adhesion on the site of dermatophytosis, ample absorption of exudates during treatment, and customized controlled drug release. Surface topography analysis indicated that the fabricated nanofibers were regular and defect-free, comprising distinct pockets with nanoscaled diameters. Characterization and compatibility studies of tolnaftate, polymers, and their nanofibers were performed through ATR-FTIR, TGA, and PXRD. Remarkable hydrophilicity and an excellent swelling index were obtained from a 3:1 ratio of ERL100/ERS100 electrospun D3 nanofibers, which is an essential benchmark for the fabrication of nanofibrous scaffolds for alleviating dermatophytosis. In vitro drug release investigation revealed that a nonwoven nanomesh of nanofibers could control the rate of drug release for 8 h. A microdilution assay exhibited inhibition of more than 95% viable cells of Trichophyton rubrum for 96 h. However, Microsporum species rigidly restricted the effect of bioactive antifungal nanofibers and hence showed resistance. In vivo activity on Trichophyton rubrum infected Swiss albino mice revealed complete inhibition of fungal pathogens on successive applications of D3 nanofibers for 7 days. This investigation suggests potential uses of tolnaftate loaded polyacrylate nanofibers as dressing materials/scaffolds for effective

  3. Improved infiltration of stem cells on electrospun nanofibers

    International Nuclear Information System (INIS)

    Shabani, Iman; Haddadi-Asl, Vahid; Seyedjafari, Ehsan; Babaeijandaghi, Farshad; Soleimani, Masoud

    2009-01-01

    Nanofibrous scaffolds have been recently used in the field of tissue engineering because of their nano-size structure which promotes cell attachment, function, proliferation and infiltration. In this study, nanofibrous polyethersulfone (PES) scaffolds was prepared via electrospinning. The scaffolds were surface modified by plasma treatment and collagen grafting. The surface changes then investigated by contact angle measurements and FTIR-ATR. The results proved grafting of the collagen on nanofibers surface and increased hydrophilicity after plasma treatment and collagen grafting. The cell interaction study was done using stem cells because of their ability to differentiate to different kinds of cell lines. The cells had normal morphology on nanofibers and showed very high infiltration through collagen grafted PES nanofibers. This infiltration capability is very useful and needed to make 3D scaffolds in tissue engineering.

  4. Highly sensitive and ultrafast response surface acoustic wave humidity sensor based on electrospun polyaniline/poly(vinyl butyral) nanofibers

    International Nuclear Information System (INIS)

    Lin Qianqian; Li Yang; Yang Mujie

    2012-01-01

    Highlights: ► Polyanline/poly(vinyl butyral) nanofibers are prepared by electrospinning. ► Nanofiber-based SAW humidity sensor show high sensitivity and ultrafast response. ► The SAW sensor can detect very low humidity. - Abstract: Polyaniline (PANi) composite nanofibers were deposited on surface acoustic wave (SAW) resonator with a central frequency of 433 MHz to construct humidity sensors. Electrospun nanofibers of poly(methyl methacrylate), poly(vinyl pyrrolidone), poly(ethylene oxide), poly(vinylidene fluoride), poly(vinyl butyral) (PVB) were characterized by scanning electron microscopy, and humidity response of corresponding SAW humidity sensors were investigated. The results indicated that PVB was suitable as a matrix to form nanofibers with PANi by electrospinning (ES). Electrospun PANi/PVB nanofibers exhibited a core–sheath structure as revealed by transmittance electron microscopy. Effects of ES collection time on humidity response of SAW sensor based on PANi/PVB nanofibers were examined at room temperature. The composite nanofiber sensor exhibited very high sensitivity of ∼75 kHz/%RH from 20 to 90%RH, ultrafast response (1 s and 2 s for humidification and desiccation, respectively) and good sensing linearity. Furthermore, the sensor could detect humidity as low as 0.5%RH, suggesting its potentials for low humidity detection. Attempts were done to explain the attractive humidity sensing performance of the sensor by considering conductivity, hydrophilicity, viscoelasticity and morphology of the polymer composite nanofibers.

  5. Method for Coating a Tow with an Electrospun Nanofiber

    Science.gov (United States)

    Kohlman, Lee W. (Inventor); Roberts, Gary D. (Inventor)

    2015-01-01

    Method and apparatus for enhancing the durability as well as the strength and stiffness of prepreg fiber tows of the sort used in composite materials are disclosed. The method involves adhering electrospun fibers onto the surface of such composite materials as filament-wound composite objects and the surface of prepreg fiber tows of the sort that are subsequently used in the production of composite materials of the filament-wound, woven, and braided sorts. The apparatus performs the methods described herein.

  6. Current approaches to electrospun nanofibers for tissue engineering

    International Nuclear Information System (INIS)

    Rim, Nae Gyune; Shin, Heungsoo; Shin, Choongsoo S

    2013-01-01

    The ultimate goal of tissue engineering is to replace damaged tissues by applying engineering technology and the principles of life sciences. To successfully engineer a desirable tissue, three main elements of cells, scaffolds and growth factors need to be harmonized. Biomaterial-based scaffolds serve as a critical platform both to support cell adhesion and to deliver growth factors. Various methods of fabricating scaffolds have been investigated. One recently developed method that is growing in popularity is called electrospinning. Electrospinning is known for its capacity to make fibrous and porous structures that are similar to natural extracellular matrix (ECM). Other advantages to electrospinning include its ability to create relatively large surface to volume ratios, its ability to control fiber size from micro- to nano-scales and its versatility in material choice. Although early work with electrospun fibers has shown promise in the regeneration of certain types of tissues, further modification of their chemical, biological and mechanical properties would permit future advancements. In this paper, current approaches to the development of modular electrospun fibers as scaffolds for tissue engineering are discussed. Their chemical and physical characteristics can be tuned for the regeneration of specific target tissues by co-spinning of multiple materials and by post-modification of the surface of electrospun fibers. In addition, topology or structure can also be controlled to elicit specific responses from cells and tissues. The selection of proper polymers, suitable surface modification techniques and the control of the dimension and arrangement of the fibrous structure of electrospun fibers can offer versatility and tissue specificity, and therefore provide a blueprint for specific tissue engineering applications. (paper)

  7. Lignin-Based Electrospun Nanofibers Reinforced with Cellulose Nanocrystals

    Science.gov (United States)

    Mariko Ago; Kunihiko Okajima; Joseph E. Jakes; Park Sunkyu; Orlando J. Rojas

    2012-01-01

    Lignin-based fibers were produced by electrospinning aqueous dispersions of lignin, poly(vinyl alcohol) (PVA), and cellulose nanocrystals (CNCs). Defect-free nanofibers with up to 90 wt % lignin and 15% CNCs were achieved. The properties of the aqueous dispersions, including viscosity, electrical conductivity, and surface tension, were examined and correlated to the...

  8. Electrospun propolis/polyurethane composite nanofibers for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jeong In [Department of Bio-nano System Engineering, Chonbuk National University, Jeonju 561–756 (Korea, Republic of); Pant, Hem Raj, E-mail: hempant@jbnu.ac.kr [Department of Bio-nano System Engineering, Chonbuk National University, Jeonju 561–756 (Korea, Republic of); Department of Engineering Science and Humanities, Pulchowk Campus, Tribhuvan University, Kathmandu (Nepal); Research Institute for Next Generation, Kalanki, Kathmandu (Nepal); Sim, Hyun-Jaung [Department of Bioactive Material Science, Research Center of Bioactive Material, Chonbuk National University, Jeonju, Chonbuk (Korea, Republic of); Lee, Kang Min [Department of Molecular Biology, College of Natural Science, Chonbuk National University, Jeonju, 561–756 (Korea, Republic of); Kim, Cheol Sang, E-mail: chskim@jbnu.ac.kr [Department of Bio-nano System Engineering, Chonbuk National University, Jeonju 561–756 (Korea, Republic of)

    2014-11-01

    Tissue engineering requires functional polymeric membrane for adequate space for cell migration and attachment within the nanostructure. Therefore, biocompatible propolis loaded polyurethane (propolis/PU) nanofibers were successfully prepared using electrospinning of propolis/PU blend solution. Here, composite nanofibers were subjected to detailed analysis using electron microscopy, FT-IR spectroscopy, thermal gravimetric analysis (TGA), and mechanical properties and water contact angle measurement. FE-SEM images revealed that the composite nanofibers became point-bonded with increasing amounts of propolis in the blend due to its adhesive properties. Incorporation of small amount of propolis through PU matrix could improve the hydrophilicity and mechanical strength of the fibrous membrane. In order to assay the cytocompatibility and cell behavior on the composite scaffolds, fibroblast cells were seeded on the matrix. Results suggest that the incorporation of propolis into PU fibers could increase its cell compatibility. Moreover, composite nanofibers have effective antibacterial activity. Therefore, as-synthesized nanocomposite fibrous mat has great potentiality in wound dressing and skin tissue engineering. - Highlights: • Sufficient amount of propolis is simply loaded through PU fibers. • Propolis increases the hydrophilicity and mechanical properties of PU fibers. • Composite mat shows excellent antibacterial activity. • Small amount of propolis can enhance the cell compatibility of PU fibers.

  9. Porous Carbon Nanofibers from Electrospun Biomass Tar/Polyacrylonitrile/Silver Hybrids as Antimicrobial Materials.

    Science.gov (United States)

    Song, Kunlin; Wu, Qinglin; Zhang, Zhen; Ren, Suxia; Lei, Tingzhou; Negulescu, Ioan I; Zhang, Quanguo

    2015-07-15

    A novel route to fabricate low-cost porous carbon nanofibers (CNFs) using biomass tar, polyacrylonitrile (PAN), and silver nanoparticles has been demonstrated through electrospinning and subsequent stabilization and carbonization processes. The continuous electrospun nanofibers had average diameters ranging from 392 to 903 nm. The addition of biomass tar resulted in increased fiber diameters, reduced thermal stabilities, and slowed cyclization reactions of PAN in the as-spun nanofibers. After stabilization and carbonization, the resultant CNFs showed more uniformly sized and reduced average diameters (226-507 nm) compared to as-spun nanofibers. The CNFs exhibited high specific surface area (>400 m(2)/g) and microporosity, attributed to the combined effects of phase separations of the tar and PAN and thermal decompositions of tar components. These pore characteristics increased the exposures and contacts of silver nanoparticles to the bacteria including Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli, leading to excellent antimicrobial performances of as-spun nanofibers and CNFs. A new strategy is thus provided for utilizing biomass tar as a low-cost precursor to prepare functional CNFs and reduce environmental pollutions associated with direct disposal of tar as an industrial waste.

  10. Synthesis and characterizations of Pt nanorods on electrospun polyamide-6 nanofibers templates

    International Nuclear Information System (INIS)

    Nirmala, R.; Navamathavan, R.; Won, Jeong Jin; Jeon, Kyung Soo; Yousef, Ayman; Kim, Hak Yong

    2012-01-01

    Highlights: ► Electrospun polyamide-6 nanofibers were used as the templates for synthesis Pt nanorods. ► Polyamide-6 nanofibers surfaces were plasma treated to coat Pt. ► High quality Pt nanorods were obtained by calcinations process. ► Pt nanorods with a diameter of few hundred nanometers were obtained. ► Polyamide-6 nanofibers template based Pt nanorods synthesis are a feasible method. - Abstract: We report on the synthesis of platinum (Pt) nanorods by using ultrafine polyamide-6 nanofibers templates produced via electrospinning technique. These ultrafine polyamide-6 nanofibers can be utilized as the templates for growing Pt nanorods after modifying them optimally by plasma passivations. The morphological, structural, optical and electrical properties of the template assisted Pt nanorods were studied by field-emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), photoluminescence (PL) and current–voltage (I–V) characteristics. The ability to fabricate the ultrafine size controlled Pt nanorods on polyamide-6 templates with optimized growth parameters in real time can be utilized for the variety of technological applications. Therefore, it is possible to obtain high quality with size control Pt nanorods. Once obtaining the high quality metal nanorods on polymer templates, the same can be adapted for the electronic device fabrication.

  11. Effects of substrate on piezoelectricity of electrospun poly(vinylidene fluoride)-nanofiber-based energy generators.

    Science.gov (United States)

    Lee, Byoung-Sun; Park, Boongik; Yang, Ho-Sung; Han, Jin Woo; Choong, Chweelin; Bae, Jihyun; Lee, Kihwan; Yu, Woong-Ryeol; Jeong, Unyong; Chung, U-In; Park, Jong-Jin; Kim, Ohyun

    2014-03-12

    We report the effects of various substrates and substrate thicknesses on electrospun poly(vinylidene fluoride) (PVDF)-nanofiber-based energy harvesters. The electrospun PVDF nanofibers showed an average diameter of 84.6 ± 23.5 nm. A high relative β-phase fraction (85.2%) was achieved by applying high voltage during electrospinning. The prepared PVDF nanofibers thus generated considerable piezoelectric potential in accordance with the sound-driven mechanical vibrations of the substrates. Slide glass, poly(ethylene terephthalate), poly(ethylene naphthalate), and paper substrates were used to investigate the effects of the intrinsic and extrinsic substrate properties on the piezoelectricity of the energy harvesters. The thinnest paper substrate (66 μm) with a moderate Young's modulus showed the highest voltage output (0.4885 V). We used high-performance 76, 66, and 33 μm thick papers to determine the effect of paper thickness on the output voltage. The thinnest paper substrate resulted in the highest voltage output (0.7781 V), and the numerical analyses of the sound-driven mechanical deformation strongly support the hypothesis that substrate thickness has a considerable effect on piezoelectric performance.

  12. Electrospun PCL nanofibers with anisotropic mechanical properties as a biomedical scaffold

    International Nuclear Information System (INIS)

    Kim, Geun Hyung

    2008-01-01

    To design an ideal scaffold, various factors should be considered, such as pore size and morphology, mechanical properties versus porosity, surface properties and appropriate biodegradability. Of these factors, the importance of mechanical properties on cell growth is particularly obvious in tissues such as bone, cartilage, blood vessels, tendons and muscles. Although electrospun nanofibers provide easily applicable nano-sized structures which could be used as biomedical scaffolds, the mechanical properties are poor since an increased pore size and porosity are generally accompanied by a decrease in mechanical properties. In addition, the general electrospinning has been limited to the fabrication of a variety of anisotropic mechanical properties, which are extremely important parameters for designing a musculoskeletal system. In this study, scaffolds consisting of variously oriented nanofibers were produced using an electrospinning process modified with an auxiliary electrode and a two-axis robot collecting system. Using an auxiliary electrode, a stable Taylor cone and initial spun jets were obtained. The influence of the electrode was evaluated with electric field simulation. Using the modified electrospinning process, various directions of orientation of electrospun fibers could be acquired and the fabricated oriented nanofiber webs showed a mechanically anisotropic behavior and a higher hydrophilic property compared to randomly distributed fibrous mats

  13. Electrospun carboxyl multi-walled carbon nanotubes grafted polyhydroxybutyrate composite nanofibers membrane scaffolds: Preparation, characterization and cytocompatibility.

    Science.gov (United States)

    Zhijiang, Cai; Cong, Zhu; Jie, Guo; Qing, Zhang; Kongyin, Zhao

    2018-01-01

    Electrospun polyhydroxybutyrate (PHB)/carboxyl multi-walled carbon nanotubes grafted polyhydroxybutyrate (CMWCNT-g-PHB) composite nanofibers scaffolds were fabricated by electrospinning technology. The grafted product CMWCNT-g-PHB was prepared by condensation reactions between the carboxyl groups of CMWCNT and hydroxyl groups of PHB molecules and characterized by FTIR, XRD, XPS, TG and TEM measurements. The surface morphology, hydrophilicity and tensile mechanical properties of the electrospun PHB/CMWCNT-g-PHB composite nanofibers membrane scaffolds were investigated. The values of tensile strength, breaking elongation rate, initial modulus and fracture energy of the composite nanofibers scaffolds can reach to 4.64MPa, 255.59%, 88MPa and 109.73kJ/m 2 , respectively. The biodegradability and cytocompatibility of the electrospun composite nanofibers scaffolds were preliminarily evaluated. The as-prepared electrospun PHB/CMWCNT-g-PHB composite nanofibers scaffolds with the characteristics of large specific area, high porosity, good biodegradability and cytocompatibility as well as sufficient mechanical properties should be more promising in the field of tissue engineering scaffolds and biological medicine. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Photocatalysis of low-concentration gaseous organic pollutants over electrospun iron-doped titanium dioxide nanofibers

    Science.gov (United States)

    Chun, Ho-Hwan; Lee, Joon Yeob; Jo, Wan-Kuen

    2013-11-01

    In this study, iron-doped titania (Fe-TiO2) nanoparticles were prepared and then coupled to a polymer material as a support to synthesize Fe-TiO2 nanofibers for photocatalytic degradation of gaseous pollutants (benzene, toluene, ethyl benzene, and o-xylene (BTEX)) at environmental sub-ppm levels. The characteristics of as-prepared photocatalysts were determined by SEM, XRD, and FTIR analyses. Spectral analysis of the as-prepared photocatalysts revealed that they were closely associated with the characteristics of Fe ions for Fe-TiO2 nanofibers. The photocatalytic degradation efficiencies (PDEs) of BTEX determined via Fe-TiO2 nanofibers varied with the ratios of Fe to Ti, suggesting the presence of an optimal Fe-to-Ti ratio. In addition, the PDEs of BTEX determined via two Fe-TiO2 nanofibers with low Fe-to-Ti ratios (0.001 and 0.004) were higher than those obtained from the undoped Fe-TiO2 nanofibers, whereas those of the other two Fe-TiO2 nanofibers with high Fe-to-Ti ratios (0.008 and 0.012) were lower. The average PDEs of BTEX decreased from 34 to 9%, 68 to 28%, 83 to 45%, and 90 to 55%, respectively, as the stream flow rates increased from 1 to 4 L min-1. These values also decreased with increasing initial concentration (IC). Specifically, at the lowest IC of 0.1 ppm, the average PDEs of BTEX were 33, 68, 83, and 91%, respectively, while they were 5, 8, 12, and 23%, respectively, at the highest IC of 2.0 ppm. Similarly, the PDEs of BTEX decreased significantly as the RH increased. Overall, the electrospun Fe-TiO2 nanofibers could be used to effectively decompose low-concentration gaseous organic pollutants when operational conditions were optimized.

  15. Investigation of microalgae growth on electrospun nanofiber mats

    Directory of Open Access Journals (Sweden)

    Christina Großerhode

    2017-08-01

    Full Text Available Due to their large inner surface, nanofiber mats are often used in tissue engineering and examined with respect to cell adhesion, e.g., for cultivation of fibroblasts. The combination of different polymers with a large contact area, however, could also be used for growth of different plants including green microalgae. Here, the cultivation of the microalga Chlamydomonas reinhardtii on different polymer substrates was examined. We investigated growth on two nanofiber mats consisting of polyamide (PA6 and polyacrylonitrile (PAN and a polypropylene (PP microfiber mat as substrates, compared with a pure multi-well plate. It was found that the algae were able to grow on all textile mats without change in morphology, indicating that all polymers were non-toxic to the cells. Thus, these nonwovens might be suitable filters for the separation of microalgae in biotechnological processes.

  16. Electrospun Metal Nanofiber Webs as High-Performance Transparent Electrode

    KAUST Repository

    Wu, Hui

    2010-10-13

    Transparent electrodes, indespensible in displays and solar cells, are currently dominated by indium tin oxide (ITO) films although the high price of indium, brittleness of films, and high vacuum deposition are limiting their applications. Recently, solution-processed networks of nanostructures such as carbon nanotubes (CNTs), graphene, and silver nanowires have attracted great attention as replacements. A low junction resistance between nanostructures is important for decreasing the sheet resistance. However, the junction resistances between CNTs and boundry resistances between graphene nanostructures are too high. The aspect ratios of silver nanowires are limited to ∼100, and silver is relatively expensive. Here, we show high-performance transparent electrodes with copper nanofiber networks by a low-cost and scalable electrospinning process. Copper nanofibers have ultrahigh aspect ratios of up to 100000 and fused crossing points with ultralow junction resistances, which result in high transmitance at low sheet resistance, e.g., 90% at 50 Ω/sq. The copper nanofiber networks also show great flexibility and stretchabilty. Organic solar cells using copper nanowire networks as transparent electrodes have a power efficiency of 3.0%, comparable to devices made with ITO electrodes. © 2010 American Chemical Society.

  17. Studies on electrospun nylon-6/chitosan complex nanofiber interactions

    International Nuclear Information System (INIS)

    Zhang Haitao; Li Shubai; Branford White, Christopher J.; Ning Xin; Nie Huali; Zhu Limin

    2009-01-01

    Composite membranes of nylon-6/chitosan nanofibers with different weight ratio of nylon-6 to chitosan were fabricated successfully using electrospinning. Morphologies of the nanofibers were investigated by scanning electron microscopy (SEM) and the intermolecular interactions of the nylon-6/chitosan complex were evaluated by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), differential scanning calorimetry (DSC) as well as mechanical testing. We found that morphology and diameter of the nanofibers were influenced by the concentration of the solution and weight ratio of the blending component materials. Furthermore FT-IR analyses on interactions between components demonstrated an IR band frequency shift that appeared to be dependent on the amount of chitosan in the complex. Observations from XRD and DSC suggested that a new fraction of γ phase crystals appeared and increased with the increasing content of chitosan in blends, this indicated that intermolecular interactions occurred between nylon-6 and chitosan. Results from performance data in mechanical showed that intermolecular interactions varied with varying chitosan content in the fibers. It was concluded that a new composite product was created and the stability of this system was attributed to strong new interactions such as hydrogen bond formation between the nylon-6 polymers and chitosan structures.

  18. A Review of Electrospun Conductive Polyaniline Based Nanofiber Composites and Blends: Processing Features, Applications, and Future Directions

    Directory of Open Access Journals (Sweden)

    Saiful Izwan Abd Razak

    2015-01-01

    Full Text Available Electrospun polymer nanofibers with high surface area to volume ratio and tunable characteristic are formed through the application of strong electrostatic field. Electrospinning has been identified as a straight forward and viable technique to produce nanofibers from polymer solution as their initial precursor. These nanofiber materials have attracted attention of researchers due to their enhanced and exceptional nanostructural characteristics. Electrospun polyaniline (PANI based nanofiber is one of the important new materials for the rapidly growing technology development such as nanofiber based sensor devices, conductive tissue engineering scaffold materials, supercapacitors, and flexible solar cells applications. PANI however is relatively hard to process compared to that of other conventional polymers and plastics. The processing of PANI is daunting, mainly due to its rigid backbone which is related to its high level of conjugation. The challenges faced in the electrospinning processing of neat PANI have alternatively led to the development of the electrospun PANI based composites and blends. A review on the research activities of the electrospinning processing of the PANI based nanofibers, the potential prospect in various fields, and their future direction are presented.

  19. Fabrication, functionalization, and application of electrospun biopolymer nanofibers.

    Science.gov (United States)

    Kriegel, Christina; Arecchi, Alessandra; Arrechi, Alessandra; Kit, Kevin; McClements, D J; Weiss, Jochen

    2008-09-01

    The use of novel nanostructured materials has attracted considerable interest in the food industry for their utilization as highly functional ingredients, high-performance packaging materials, processing aids, and food quality and safety sensors. Most previous application interest has focused on the development of nanoparticles. However, more recently, the ability to produce non-woven mats composed of nanofibers that can be used in food applications is beginning to be investigated. Electrospinning is a novel fabrication technique that can be used to produce fibers with diameters below 100 nm from (bio-) polymer solutions. These nanofibers have been shown to possess unique properties that distinguish them from non-woven fibers produced by other methods, e.g., melt-blowing. This is because first the process involved results in a high orientation of polymers within the fibers that leads to mechanically superior properties, e.g., increased tensile strengths. Second, during the spinning of the fibers from polymer solutions, the solvent is rapidly evaporated allowing the production of fibers composed of polymer blends that would typically phase separate if spun with other processes. Third, the small dimensions of the fibers lead to very high specific surface areas. Because of this the fiber properties may be greatly influenced by surface properties giving rise to fiber functionalities not found in fibers of larger sizes. For food applications, the fibers may find uses as ingredients if they are composed solely of edible polymers and GRAS ingredients, (e.g., fibers could contain functional ingredients such as nutraceuticals, antioxidants, antimicrobials, and flavors), as active packaging materials or as processing aids (e.g., catalytic reactors, membranes, filters (Lala et al., 2007), and sensors (Manesh et al., 2007; Ren et al., 2006; Sawicka et al., 2005). This review is therefore intended to introduce interested food and agricultural scientists to the concept of nano-fiber

  20. The potential applications of fibrin-coated electrospun polylactide nanofibers in skin tissue engineering

    Czech Academy of Sciences Publication Activity Database

    Bačáková, Markéta; Musílková, Jana; Riedel, Tomáš; Stránská, D.; Brynda, Eduard; Žaloudková, Margit; Bačáková, Lucie

    2016-01-01

    Roč. 11, č. 2016 (2016), s. 771-789 E-ISSN 1178-2013 R&D Projects: GA ČR(CZ) GBP108/12/G108; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:67985823 ; RVO:61389013 ; RVO:67985891 Keywords : electrospun nanofibers * nanocoating * skin tissue engineering * fibroblasts * fibrin Subject RIV: EI - Biotechnology ; Bionics; CD - Macromolecular Chemistry (UMCH-V); JI - Composite Materials (USMH-B) Impact factor: 4.300, year: 2016

  1. Preparation and characterization of a novel electrospun ammonium molybdophosphate/polyacrylonitrile nanofiber adsorbent for cesium removal

    International Nuclear Information System (INIS)

    Amin Tabatabaeefar; Mohammad Ali Moosavian; Ali Reza Keshtkar

    2015-01-01

    Adsorption of Cs + ion from aqueous solution onto a novel electrospun ammonium molybdophosphate/polyacrylonitrile nanofiber adsorbent with variation in AMP content, adsorbent concentration, pH, contact time, initial concentration and temperature was studied. The physicochemical characterization was performed by FTIR, XRD, BET and SEM analyses. Langmuir, Freundlich and Dubinin-Radushkevich models were used for analysis of equilibrium data. Kinetic results showed that the experimental data best fitted the pseudo-second-order kinetic model. The adsorption affinity of metal ions onto adsorbent was in order of Cs + > Co 2+ > Mg 2+ > Ca 2+ > Sr 2+ . The adsorbent could be easily regenerated after five cycles of adsorption-desorption. (author)

  2. Abdominal closure reinforcement by using polypropylene mesh functionalized with poly-ε-caprolactone nanofibers and growth factors for prevention of incisional hernia formation.

    Science.gov (United States)

    Plencner, Martin; East, Barbora; Tonar, Zbyněk; Otáhal, Martin; Prosecká, Eva; Rampichová, Michala; Krejčí, Tomáš; Litvinec, Andrej; Buzgo, Matej; Míčková, Andrea; Nečas, Alois; Hoch, Jiří; Amler, Evžen

    2014-01-01

    Incisional hernia affects up to 20% of patients after abdominal surgery. Unlike other types of hernia, its prognosis is poor, and patients suffer from recurrence within 10 years of the operation. Currently used hernia-repair meshes do not guarantee success, but only extend the recurrence-free period by about 5 years. Most of them are nonresorbable, and these implants can lead to many complications that are in some cases life-threatening. Electrospun nanofibers of various polymers have been used as tissue scaffolds and have been explored extensively in the last decade, due to their low cost and good biocompatibility. Their architecture mimics the natural extracellular matrix. We tested a biodegradable polyester poly-ε-caprolactone in the form of nanofibers as a scaffold for fascia healing in an abdominal closure-reinforcement model for prevention of incisional hernia formation. Both in vitro tests and an experiment on a rabbit model showed promising results.

  3. Synthesis and Process Optimization of Electrospun PEEK-Sulfonated Nanofibers by Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    Carlo Boaretti

    2015-07-01

    Full Text Available In this study electrospun nanofibers of partially sulfonated polyether ether ketone have been produced as a preliminary step for a possible development of composite proton exchange membranes for fuel cells. Response surface methodology has been employed for the modelling and optimization of the electrospinning process, using a Box-Behnken design. The investigation, based on a second order polynomial model, has been focused on the analysis of the effect of both process (voltage, tip-to-collector distance, flow rate and material (sulfonation degree variables on the mean fiber diameter. The final model has been verified by a series of statistical tests on the residuals and validated by a comparison procedure of samples at different sulfonation degrees, realized according to optimized conditions, for the production of homogeneous thin nanofibers.

  4. Synthesis and Process Optimization of Electrospun PEEK-Sulfonated Nanofibers by Response Surface Methodology

    Science.gov (United States)

    Boaretti, Carlo; Roso, Martina; Lorenzetti, Alessandra; Modesti, Michele

    2015-01-01

    In this study electrospun nanofibers of partially sulfonated polyether ether ketone have been produced as a preliminary step for a possible development of composite proton exchange membranes for fuel cells. Response surface methodology has been employed for the modelling and optimization of the electrospinning process, using a Box-Behnken design. The investigation, based on a second order polynomial model, has been focused on the analysis of the effect of both process (voltage, tip-to-collector distance, flow rate) and material (sulfonation degree) variables on the mean fiber diameter. The final model has been verified by a series of statistical tests on the residuals and validated by a comparison procedure of samples at different sulfonation degrees, realized according to optimized conditions, for the production of homogeneous thin nanofibers. PMID:28793427

  5. Evaluation of Electrospun PCL-PIBMD Meshes Modified with Plasmid Complexes in Vitro and in Vivo

    Directory of Open Access Journals (Sweden)

    Yakai Feng

    2016-02-01

    Full Text Available Functional artificial vascular meshes from biodegradable polymers have been widely explored for certain tissue engineered meshes. Still, the foreign body reaction and limitation in endothelialization are challenges for such devices. Here, degradable meshes from phase-segregated multiblock copolymers consisting of poly(ε-caprolactone (PCL and polydepsipeptide segments are successfully prepared by electrospinning and electrospraying techniques. The pEGFP-ZNF580 plasmid microparticles (MPs-pZNF580 were loaded into the electrospun meshes to enhance endothelialization. These functional meshes were evaluated in vitro and in vivo. The adhesion and proliferation of endothelial cells on the meshes were enhanced in loaded mesh groups. Moreover, the hemocompatibility and the tissue response of the meshes were further tested. The complete tests showed that the vascular meshes modified with MPs-pZNF580 possessed satisfactory performance with an average fiber diameter of 550 ± 160 nm, tensile strength of 27 ± 3 MPa, Young’s modulus of 1. 9 ± 0.2 MPa, water contact angle of 95° ± 2°, relative cell number of 122% ± 1% after 7 days of culture, and low blood platelet adhesion as well as weak inflammatory reactions compared to control groups.

  6. Fabrication and characterization of electrospun orthorhombic InVO4 nanofibers

    Science.gov (United States)

    Song, Lingjun; Liu, Suwen; Lu, Qifang; Zhao, Gang

    2012-02-01

    The novel orthorhombic InVO4 nanofibers have been successfully synthesized by annealing electrospun precursor fibers. Citric acid was used as a ligand for it could react with metal salts to get a transparent homogeneous precursor solution and homogeneous precursor sol for electrospining. Polyvinyl pyrrolidone (PVP, K-30) was used as a binder and a structure guide reagent because it was one kind of water-soluble polymers. It is easy to gain one-dimensional materials while the viscosity of the citrate/PVP sol was suitable. The structure, morphology and photocatalytic properties of the nanofibers were characterized by X-ray diffraction (XRD), thermogravimetry analysis (TGA), scanning electron microscopy (SEM) analysis, UV-vis spectrophotometer and fluorescence spectrophotometer. The nanofibers calcined at 700 °C were orthorhombic InVO4 with a width in the range of 30-100 nm and length in micron-grade. This one-dimensional pure orthorhombic InVO4 had the higher photocatalytic activity under visible light irradiation. The photo-degradation rate of nitrobenzene aqueous solution under visible light reached 69% after 6 h. It is obvious that the orthorhombic InVO4 nanofibers have a potential application in wastewater-treatment.

  7. Catalytically Graphitized Electrospun Carbon Nanofibers Adorned with Nickel Nanoparticles for Catalysis Applications

    Directory of Open Access Journals (Sweden)

    A. M. Bazargan

    2016-01-01

    Full Text Available Catalytically graphitized electrospun carbon nanofibers adorned uniformly with fine nickel nanoparticles were successfully prepared. The procedure was based on the electrospinning technique and the use of nickel precursor to create both graphitized nanofibers and nickel nanoparticles under a relatively low-temperature heat treatment. The X-ray diffraction and Raman results clearly proved catalytic graphitization of polymer-based carbon fibers in the presence of nickel catalyst. Taking the results from scanning and transmission electron microscopies and X-ray diffraction into account, it was inferred that during the heat treatment, nickel atoms have diffused through the nanofibers and formed fine nickel nanoparticles on the surface of graphitized nanofibers to make a well stabilized heterogeneous nanostructure. The results from Brunauer–Emmett–Teller technique also showed a high surface area value of 140.2 m2g-1 for the obtained structure. All these attributes along with the fibrous and porous structure enable the product to serve as a potential candidate in the catalysis applications.

  8. Alignment of Electrospun Nanofibers and Prediction of Electrospinning Linear Speed Using a Rotating Jet

    Directory of Open Access Journals (Sweden)

    M. Khamforoush

    2009-12-01

    Full Text Available Anew and effective electrospinning method has been developed for producing aligned polymer nanofibers. The conventional electrospinning technique has been modified to fabricate nanofibers as uniaxially aligned array. The key to the success of this technique is the creation of a rotating jet by using a cylindrical collector in which the needle tip is located at its center. The unique advantage of this method among the current methods is the ability of apparatus to weave continuously nanofibers in uniaxially aligned form. Fibers produced by this method are well-aligned, with several meters in length, and can be spread over a large area. We have employed a voltage range of (6-16 kV, a collector diameter in the range of 20-50 cm and various concentrations of PAN solutions ranging from 15 wt% to 19 wt %. The electrospun nanofibers could be conveniently formed onto the surface of any thin substrate such as glass sampling plate for subsequent treatments and other applications. Therefore, the linear speed of electrospinning process is determined experimentally as a function of cylindrical collector diameter, polymer concentration and field potential  difference.

  9. Development of Omniphobic Desalination Membranes Using a Charged Electrospun Nanofiber Scaffold.

    Science.gov (United States)

    Lee, Jongho; Boo, Chanhee; Ryu, Won-Hee; Taylor, André D; Elimelech, Menachem

    2016-05-04

    In this study, we present a facile and scalable approach to fabricate omniphobic nanofiber membranes by constructing multilevel re-entrant structures with low surface energy. We first prepared positively charged nanofiber mats by electrospinning a blend polymer-surfactant solution of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) and cationic surfactant (benzyltriethylammonium). Negatively charged silica nanoparticles (SiNPs) were grafted on the positively charged electrospun nanofibers via dip-coating to achieve multilevel re-entrant structures. Grafted SiNPs were then coated with fluoroalkylsilane to lower the surface energy of the membrane. The fabricated membrane showed excellent omniphobicity, as demonstrated by its wetting resistance to various low surface tension liquids, including ethanol with a surface tension of 22.1 mN/m. As a promising application, the prepared omniphobic membrane was tested in direct contact membrane distillation to extract water from highly saline feed solutions containing low surface tension substances, mimicking emerging industrial wastewaters (e.g., from shale gas production). While a control hydrophobic PVDF-HFP nanofiber membrane failed in the desalination/separation process due to low wetting resistance, our fabricated omniphobic membrane exhibited a stable desalination performance for 8 h of operation, successfully demonstrating clean water production from the low surface tension feedwater.

  10. Comparison of cell behavior on pva/pva-gelatin electrospun nanofibers with random and aligned configuration.

    Science.gov (United States)

    Huang, Chen-Yu; Hu, Keng-Hsiang; Wei, Zung-Hang

    2016-12-05

    Electrospinning technique is able to create nanofibers with specific orientation. Poly(vinyl alcohol) (PVA) have good mechanical stability but poor cell adhesion property due to the low affinity of protein. In this paper, extracellular matrix, gelatin is incorporated into PVA solution to form electrospun PVA-gelatin nanofibers membrane. Both randomly oriented and aligned nanofibers are used to investigate the topography-induced behavior of fibroblasts. Surface morphology of the fibers is studied by optical microscopy and scanning electron microscopy (SEM) coupled with image analysis. Functional group composition in PVA or PVA-gelatin is investigated by Fourier Transform Infrared (FTIR). The morphological changes, surface coverage, viability and proliferation of fibroblasts influenced by PVA and PVA-gelatin nanofibers with randomly orientated or aligned configuration are systematically compared. Fibroblasts growing on PVA-gelatin fibers show significantly larger projected areas as compared with those cultivated on PVA fibers which p-value is smaller than 0.005. Cells on PVA-gelatin aligned fibers stretch out extensively and their intracellular stress fiber pull nucleus to deform. Results suggest that instead of the anisotropic topology within the scaffold trigger the preferential orientation of cells, the adhesion of cell membrane to gelatin have substantial influence on cellular behavior.

  11. Uniaxially aligned electrospun all-cellulose nanocomposite nanofibers reinforced with cellulose nanocrystals: scaffold for tissue engineering.

    Science.gov (United States)

    He, Xu; Xiao, Qiang; Lu, Canhui; Wang, Yaru; Zhang, Xiaofang; Zhao, Jiangqi; Zhang, Wei; Zhang, Ximu; Deng, Yulin

    2014-02-10

    Uniaxially aligned cellulose nanofibers with well oriented cellulose nanocrystals (CNCs) embedded were fabricated via electrospinning using a rotating drum as the collector. Scanning electron microscope (SEM) images indicated that most cellulose nanofibers were uniaxially aligned. The incorporation of CNCs into the spinning dope resulted in more uniform morphology of the electrospun cellulose/CNCs nanocomposite nanofibers (ECCNN). Polarized light microscope (PLM) and transmission electron microscope (TEM) showed that CNCs dispersed well in ECCNN nonwovens and achieved considerable orientation along the long axis direction. This unique hierarchical microstructure of ECCNN nonwovens gave rise to remarkable enhancement of their physical properties. By incorporating 20% loading (in weight) of CNCs, the tensile strength and elastic modulus of ECCNN along the fiber alignment direction were increased by 101.7 and 171.6%, respectively. Their thermal stability was significantly improved as well. In addition, the ECCNN nonwovens were assessed as potential scaffold materials for tissue engineering. It was elucidated from MTT tests that the ECCNN were essentially nontoxic to human cells. Cell culture experiments demonstrated that cells could proliferate rapidly not only on the surface but also deep inside the ECCNN. More importantly, the aligned nanofibers of ECCNN exhibited a strong effect on directing cellular organization. This feature made the scaffold particularly useful for various artificial tissues or organs, such as blood vessel, tendon, nerve, and so on, in which cell orientation was crucial for their performance.

  12. The quintuple-shape memory effect in electrospun nanofiber membranes

    Science.gov (United States)

    Zhang, Fenghua; Zhang, Zhichun; Liu, Yanju; Lu, Haibao; Leng, Jinsong

    2013-08-01

    Shape memory fibrous membranes (SMFMs) are an emerging class of active polymers, which are capable of switching from a temporary shape to their permanent shape upon appropriate stimulation. Quintuple-shape memory membranes based on the thermoplastic polymer Nafion, with a stable fibrous structure, are achieved via electrospinning technology, and possess a broad transition temperature. The recovery of multiple temporary shapes of electrospun membranes can be triggered by heat in a single triple-, quadruple-, quintuple-shape memory cycle, respectively. The fiber morphology and nanometer size provide unprecedented design flexibility for the adjustable morphing effect. SMFMs enable complex deformations at need, having a wide potential application field including smart textiles, artificial intelligence robots, bio-medical engineering, aerospace technologies, etc in the future.

  13. Electrospun biodegradable nanofiber nonwovens for controlled release of proteins.

    Science.gov (United States)

    Maretschek, Sascha; Greiner, Andreas; Kissel, Thomas

    2008-04-21

    Electrospinning of emulsions composed of an organic poly(l-lactide) solution and an aqueous protein solution yielded protein containing nanofiber nonwovens (NNs) having a mean fiber diameter of approximately 350 nm. Cytochrome C was chosen as a hydrophilic model protein for encapsulation. SEM imaging and gas adsorption measurements were carried out to determine morphology and surface characteristics of the different nanofiber nonwovens. Transmission electron microscopy was used to clarify the localization of the protein within the NN. PLLA NNs exhibited a highly hydrophobic surface which led to a slow wetting. It was shown that the protein release was dependent on the surface tension of the release medium. Electrospinning of emulsions consisting of an organic solution of PLLA and an aqueous solution of hydrophilic polymers yielded fibers composed of a polymer blend. The resulting NNs exhibited a less hydrophobic surface, which gave us the opportunity to tailor the release profile via this technology. Furthermore it was investigated how the addition of different amounts of hydrophilic polymer to the aqueous phase influenced the morphology of the resulting NNs.

  14. Electrospun core-shell nanofibers derived Fe-S/N doped carbon material for oxygen reduction reaction

    Science.gov (United States)

    Guo, Junxia; Niu, Qijian; Yuan, Yichun; Maitlo, Inamullh; Nie, Jun; Ma, Guiping

    2017-09-01

    One-dimensional (1D) nanomaterials have gained attention in energy conversion, storage, and catalyst due to the unique physical and chemical properties. Electrospinning is a kind of simple, versatile, and cost-effective technology to fabricate 1D functional nanofibers. Herein, electrospun polyacrylonitrile (PAN), melamine, and ferric chloride hexahydrate (FeCl3·6H2O) composite nanofibers are used as template, and polythiophene (PT) are prepared by photopolymerization technology on the surface of electrospun nanofibers as shell part of fibers. Then, the core-shell nanofibers are pyrolyzed and converted into Fe-S/N-C nanofibers, which can be used as catalysts for ORR due to the metal and S-/N-codoped structure and unique 1D structure which provided facile pathways for efficient mass transport and charge transfer. The ORR electrocatalytic ability of Fe-S/N-C nanofibers is tested and present excellent property, especially in stability and methanol crossover. The electrocatalytic ability of sample is comparable to that of 20 wt% Pt/C benchmarks. These results offer an easy pathway for exploring metal-heteroatom-codoped carbon nanofibers applicable for ORR catalyst.

  15. Incorporation of Rutin in Electrospun Pullulan/PVA Nanofibers for Novel UV-Resistant Properties.

    Science.gov (United States)

    Qian, Yongfang; Qi, Mengjie; Zheng, Laijiu; King, Martin W; Lv, Lihua; Ye, Fang

    2016-06-23

    This study aimed to investigate the incorporation of rutin into electrospun pullulan and poly(vinyl alcohol) (PVA) nanofibers to obtain ultraviolet (UV)-resistant properties. The effect of weight ratios between pullulan and PVA, and the addition of rutin on the nanofibers' morphology and diameters were studied and characterized by scanning electron microscopy (SEM). Fourier transform infrared (FTIR) analysis was utilized to investigate the interaction between pullulan and PVA, as well as with rutin. The results showed that the inclusion of PVA results in the increase in the fiber's diameter. The addition of rutin had no obvious effect on the fibers' average diameters when the content of rutin was less than 7.41%. FTIR results indicated that a hydrogen bond formed between pullulan and PVA, also between these polymers and rutin. Moreover, the addition of rutin could enhance the mechanical properties due to its stiff structure and could decrease the transmittance of UVA and UVB to be fewer than 5%; meanwhile, the value of ultraviolet protection factor (UPF) reached more than 40 and 50 when the content of rutin was 4.46% and 5.67%, respectively. Therefore, the electrospun pullulan/PVA/rutin nanofibrous mats showed excellent UV resistance and have potential applications in anti-ultraviolet packaging and dressing materials.

  16. Fabrication of an all SU-8 electrospun nanofiber based supercapacitor

    International Nuclear Information System (INIS)

    Jao, Pit Fee; Kim, Kyoung Tae; Kim, Gloria Jung-A; Yoon, Yong-Kyu

    2013-01-01

    Supercapacitors (SCs) as energy storage devices are advantageous in their rapid charge/discharge capabilities and their immense charge storage capacity. Two important components of a SC are the electrically conductive electrodes (anode and cathode) and an electrically non-conductive separator between the two electrodes. This paper details a fabrication process for nanofibrous carbon electrodes and a nanoporous polymer separator using all SU-8 based electrospinning and post electrospinning processes, such as lithographical patterning, conversion of the nanofibrous polymer to carbon structures using heat treatment (carbonization) and their assembly to complete a SC. The process produces immensely porous electrodes with good conductivity; it is scalable and economical compared with the carbon nanotube electrode approach. High throughput tube nozzle electrospinning for nanofiber (NF) production and its photolithographical patterning have been employed to facilitate manufacturability. The dependence of the NF morphology on the carbonization temperatures is studied. Also, SC testing and characterization are discussed. (paper)

  17. In vitro evaluation of the effects of electrospun PCL nanofiber mats containing the microalgae Spirulina (Arthrospira) extract on primary astrocytes.

    Science.gov (United States)

    Kim, Sung Hoon; Shin, Chungwhan; Min, Seul Ki; Jung, Sang-Myung; Shin, Hwa Sung

    2012-02-01

    The blue-green microalgae, Spirulina, a harmless food and pharmaceutical additive, has several bioactive compounds that have therapeutic functions. Polycaprolactone (PCL) is a biocompatible and biodegradable polymer that has widely been used for tissue engineering. The electrospun PCL nanofiber containing Spirulina (PCL-Spirulina) was fabricated and tested as a potential extracellular matrix material for a culture of primary astrocytes, which play important roles in CNS injured systems. Spirulina extract was observed to increase growth and metabolic activity of rat primary astrocytes without any harm once added to the culture media. However, PCL-Spirulina nanofiber was proven to alleviate astrocyte activity. Through this research and to the best of our knowledge, we first suggest a novel composite nanomaterial, an electrospun PCL-Spirulina nanofiber that could be used to treat CNS injured systems. Copyright © 2011 Elsevier B.V. All rights reserved.

  18. High lithium electroactivity of electrospun CuFe2O4 nanofibers as anode material for lithium-ion batteries

    International Nuclear Information System (INIS)

    Luo, Lei; Cui, Rongrong; Qiao, Hui; Chen, Ke; Fei, Yaqian; Li, Dawei; Pang, Zengyuan; Liu, Ke; Wei, Qufu

    2014-01-01

    Graphical abstract: Electrospun CuFe 2 O 4 nanofibers were used as anode material for lithium-ion batteries for the first time. - Highlights: • We successfully synthesized electrospun CuFe 2 O 4 nanofibers anode material for lithium-ion batteries for the first time. • The as-prepared CuFe 2 O 4 nanofibers calcined at 800 °C exhibited a high initial discharge capacity of 1226.0 mAh g −1 , and maintained a stable capacity of 572.4 mAh g −1 after 50 cycles. • The as-prepared CuFe 2 O 4 nanofibers calcined at 800 °C also showed high capacity at higher discharge and charge rate. - Abstract: In this study, copper ferrite (CuFe 2 O 4 ) nanofibers were successfully fabricated by a combination of electrospinning and calcination process. The crystal structure was investigated by X-ray diffractomentry, and the results show only peaks of CuFe 2 O 4 could be observed from the product obtained at 800 °C, indicating the formation of pure compound. SEM and TEM images showed the as-spun CuFe 2 O 4 nanofibers possessed good continuous fiber morphology with an average diameter of about 66 nm. The electrochemical properties of electrospun CuFe 2 O 4 nanofibers as anode material for lithium-ion batteries were discussed for the first time. The results demonstrated that the electrospun CuFe 2 O 4 nanofibers anode exhibited a high initial discharge capacity of 1226.0 mAh g −1 , and maintained a stable capacity of 572.4 mAh g −1 after 50 cycles. Meanwhile, the electrodes showed high capacity at higher discharge and charge rate. The excellent electrochemical properties of electrospun CuFe 2 O 4 nanofibers anode were attributed to the high crystallinity, as well as the unique mesoporous and fibrous structures

  19. A continuous process to align electrospun nanofibers into parallel and crossed arrays

    Energy Technology Data Exchange (ETDEWEB)

    Laudenslager, Michael J.; Sigmund, Wolfgang M., E-mail: wsigm@mse.ufl.edu [University of Florida, Department of Materials Science and Engineering (United States)

    2013-04-15

    Electrical, optical, and mechanical properties of nanofibers are strongly affected by their orientation. Electrospinning is a nanofiber processing technique that typically produces nonwoven meshes of randomly oriented fibers. While several alignment techniques exist, they are only able to produce either a very thin layer of aligned fibers or larger quantities of fibers with less control over their alignment and orientation. The technique presented herein fills the gap between these two methods allowing one to produce thick meshes of highly oriented nanofibers. In addition, this technique is not limited to collection of fibers along a single axis. Modifications to the basic setup allow collection of crossed fibers without stopping and repositioning the apparatus. The technique works for a range of fiber sizes. In this study, fiber diameters ranged from 100 nm to 1 micron. This allows a few fibers at a time to rapidly deposit in alternating directions creating an almost woven structure. These aligned nanofibers have the potential to improve the performance of energy storage and thermoelectric devices and hold great promise for directed cell growth applications.

  20. Advances in electrospun nanofibers for bone and cartilage regeneration.

    Science.gov (United States)

    Ghasemi-Mobarakeh, Laleh; Prabhakaran, Molamma P; Balasubramanian, Preethi; Jin, Guorui; Valipouri, Afsaneh; Ramakrishna, Seeram

    2013-07-01

    Regeneration of bone and cartilage tissues has been an important issue for biological repair in the field of regenerative medicine. The rapidly emerging field of tissue engineering holds great promise for repair and generation of functional bone and cartilage substitutes with a combination of biomaterials, cells, drugs and growth factors. Scaffolds play a pivotal role in tissue engineering as they mimic the natural extracellular matrix (ECM) and play an important role in guiding cell adhesion and proliferation, and maintaining the normal phenotype of the tissues. The use of tissue-engineered grafts based on scaffolds has found to be a more effective method than conventional implantations of autograft, allograft, xenograft. In recent years much attention has been given to electrospinning as a feasible and versatile technique for fabrication of nanofibrous scaffolds, with large surface area to volume ratio, high porosity, mechanical properties and physical dimension similar to the ECM of natural tissues. Extensive research has been carried out for fabrication polymeric nanofibrous substrates with incorporation of hydroxyapatite nanoparticles or bone morphogenetic protein molecules for efficient tissue repair. Here we review on the literature of electrospun nanofibrous scaffolds, their modifications, and advances aimed towards the rapid regeneration of bone and cartilage.

  1. Functional electrospun polystyrene nanofibers incorporating α-, β-, and γ-cyclodextrins: comparison of molecular filter performance.

    Science.gov (United States)

    Uyar, Tamer; Havelund, Rasmus; Hacaloglu, Jale; Besenbacher, Flemming; Kingshott, Peter

    2010-09-28

    Electrospinning has been used to successfully create polystyrene (PS) nanofibers containing either of three different types of cyclodextrin (CD); α-CD, β-CD, and γ-CD. These three CDs are chosen because they have different sized cavities that potentially allow for selective inclusion complex (IC) formation with molecules of different size or differences in affinity of IC formation with one type of molecule. The CD containing electrospun PS nanofibers (PS/CD) were initially characterized by scanning electron microscopy (SEM) to determine the uniformity of the fibers and their fiber diameter distributions. X-ray photoelectron spectroscopy (XPS) was used to quantitatively determine the concentration of each CD on the different fiber surfaces. Static time-of-flight secondary ion mass spectrometry (static-ToF-SIMS) showed the presence of each type of CD on the PS nanofibers by the detection of both the CD sodium adduct molecular ions (M + Na+) and lower molecular weight oxygen containing fragment ions. The comparative efficiency of the PS/CD nanofibers/nanoweb for removing phenolphthalein, a model organic compound, from solution was determined by UV-vis spectrometry, and the kinetics of phenolphthalein capture was shown to follow the trend PS/α-CD > PS/β-CD > PS/γ-CD. Direct pyrolysis mass spectrometry (DP-MS) was also performed to ascertain the relative binding strengths of the phenolphthalein for the CD cavities, and the results showed the trend in the interaction strength was β-CD > γ-CD > α-CD. Our results demonstrate that nanofibers produced by electrospinning that incorporate cyclodextrins with different sized cavities can indeed filter organic molecules and can potentially be used for filtration, purification, and/or separation processes.

  2. Endothelial differentiation of human stem cells seeded onto electrospun polyhydroxybutyrate/polyhydroxybutyrate-co-hydroxyvalerate fiber mesh.

    Directory of Open Access Journals (Sweden)

    Alessandra Zonari

    Full Text Available Tissue engineering is based on the association of cultured cells with structural matrices and the incorporation of signaling molecules for inducing tissue regeneration. Despite its enormous potential, tissue engineering faces a major challenge concerning the maintenance of cell viability after the implantation of the constructs. The lack of a functional vasculature within the implant compromises the delivery of nutrients to and removal of metabolites from the cells, which can lead to implant failure. In this sense, our investigation aims to develop a new strategy for enhancing vascularization in tissue engineering constructs. This study's aim was to establish a culture of human adipose tissue-derived stem cells (hASCs to evaluate the biocompatibility of electrospun fiber mesh made of polyhydroxybutyrate (PHB and its copolymer poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHB-HV and to promote the differentiation of hASCs into the endothelial lineage. Fiber mesh was produced by blending 30% PHB with 70% PHB-HV and its physical characterization was conducted using scanning electron microscopy analysis (SEM. Using electrospinning, fiber mesh was obtained with diameters ranging 300 nm to 1.3 µm. To assess the biological performance, hASCs were extracted, cultured, characterized by flow cytometry, expanded and seeded onto electrospun PHB/PHB-HV fiber mesh. Various aspects of the cells were analyzed in vitro using SEM, MTT assay and Calcein-AM staining. The in vitro evaluation demonstrated good adhesion and a normal morphology of the hASCs. After 7, 14 and 21 days of seeding hASCs onto electrospun PHB/PHB-HV fiber mesh, the cells remained viable and proliferative. Moreover, when cultured with endothelial differentiation medium (i.e., medium containing VEGF and bFGF, the hASCs expressed endothelial markers such as VE-Cadherin and the vWF factor. Therefore, the electrospun PHB/PHB-HV fiber mesh appears to be a suitable material that can be used in

  3. Endothelial Differentiation of Human Stem Cells Seeded onto Electrospun Polyhydroxybutyrate/Polyhydroxybutyrate-Co-Hydroxyvalerate Fiber Mesh

    Science.gov (United States)

    Zonari, Alessandra; Novikoff, Silviene; Electo, Naira R. P.; Breyner, Natália M.; Gomes, Dawidson A.; Martins, Albino; Neves, Nuno M.; Reis, Rui L.; Goes, Alfredo M.

    2012-01-01

    Tissue engineering is based on the association of cultured cells with structural matrices and the incorporation of signaling molecules for inducing tissue regeneration. Despite its enormous potential, tissue engineering faces a major challenge concerning the maintenance of cell viability after the implantation of the constructs. The lack of a functional vasculature within the implant compromises the delivery of nutrients to and removal of metabolites from the cells, which can lead to implant failure. In this sense, our investigation aims to develop a new strategy for enhancing vascularization in tissue engineering constructs. This study's aim was to establish a culture of human adipose tissue-derived stem cells (hASCs) to evaluate the biocompatibility of electrospun fiber mesh made of polyhydroxybutyrate (PHB) and its copolymer poly-3-hydroxybutyrate-co-3-hydroxyvalerate (PHB-HV) and to promote the differentiation of hASCs into the endothelial lineage. Fiber mesh was produced by blending 30% PHB with 70% PHB-HV and its physical characterization was conducted using scanning electron microscopy analysis (SEM). Using electrospinning, fiber mesh was obtained with diameters ranging 300 nm to 1.3 µm. To assess the biological performance, hASCs were extracted, cultured, characterized by flow cytometry, expanded and seeded onto electrospun PHB/PHB-HV fiber mesh. Various aspects of the cells were analyzed in vitro using SEM, MTT assay and Calcein-AM staining. The in vitro evaluation demonstrated good adhesion and a normal morphology of the hASCs. After 7, 14 and 21 days of seeding hASCs onto electrospun PHB/PHB-HV fiber mesh, the cells remained viable and proliferative. Moreover, when cultured with endothelial differentiation medium (i.e., medium containing VEGF and bFGF), the hASCs expressed endothelial markers such as VE-Cadherin and the vWF factor. Therefore, the electrospun PHB/PHB-HV fiber mesh appears to be a suitable material that can be used in combination with

  4. Comparison of Adsorption/Desorption of Volatile Organic Compounds (VOCs) on Electrospun Nanofibers with Tenax TA for Potential Application in Sampling.

    Science.gov (United States)

    Chu, Lanling; Deng, Siwei; Zhao, Renshan; Deng, Jianjun; Kang, Xuejun

    2016-01-01

    The objective of this study was to compare the adsorption/desorption of target compounds on homemade electrospun nanofibers, polystyrene (PS) nanofibers, acrylic resin (AR) nanofibers and PS-AR composite nanofibers with Tenax TA. Ten volatile organic compounds (VOCs) were analyzed by preconcentration onto different sorbents followed by desorption (thermal and solvent orderly) and analysis by capillary gas chromatography. In comparison to Tenax TA, the electrospun nanofibers displayed a significant advantage in desorption efficiency and adsorption selectivity. Stability studies were conducted as a comparative experiment between PS-AR nanofibers and Tenax TA using toluene as the model compound. No stability problems were observed upon storage of toluene on both PS-AR nanofibers and Tenax TA over 60 hours period when maintained in an ultra-freezer (-80°C). The nanofibers provided slightly better stability for the adsorbed analytes than Tenax TA under other storage conditions. In addition, the nanofibers also provided slightly better precision than Tenax TA. The quantitative adsorption of PS-AR nanofibers exhibited a good linearity, as evidenced by the 0.988-0.999 range of regression coefficients (R). These results suggest that for VOCs sampling the electrospun nanofibers can be a potential ideal adsorbent.

  5. Comparison of Adsorption/Desorption of Volatile Organic Compounds (VOCs on Electrospun Nanofibers with Tenax TA for Potential Application in Sampling.

    Directory of Open Access Journals (Sweden)

    Lanling Chu

    Full Text Available The objective of this study was to compare the adsorption/desorption of target compounds on homemade electrospun nanofibers, polystyrene (PS nanofibers, acrylic resin (AR nanofibers and PS-AR composite nanofibers with Tenax TA. Ten volatile organic compounds (VOCs were analyzed by preconcentration onto different sorbents followed by desorption (thermal and solvent orderly and analysis by capillary gas chromatography. In comparison to Tenax TA, the electrospun nanofibers displayed a significant advantage in desorption efficiency and adsorption selectivity. Stability studies were conducted as a comparative experiment between PS-AR nanofibers and Tenax TA using toluene as the model compound. No stability problems were observed upon storage of toluene on both PS-AR nanofibers and Tenax TA over 60 hours period when maintained in an ultra-freezer (-80°C. The nanofibers provided slightly better stability for the adsorbed analytes than Tenax TA under other storage conditions. In addition, the nanofibers also provided slightly better precision than Tenax TA. The quantitative adsorption of PS-AR nanofibers exhibited a good linearity, as evidenced by the 0.988-0.999 range of regression coefficients (R. These results suggest that for VOCs sampling the electrospun nanofibers can be a potential ideal adsorbent.

  6. Electrospun Carbon Nanofiber Membranes for Filtration of Nanoparticles from Water

    Directory of Open Access Journals (Sweden)

    Mirko Faccini

    2015-01-01

    Full Text Available Nowadays, hundreds of consumer products contain metal and metal oxide nanoparticles (NP; this increases the probability of such particles to be released to natural waters generating a potential risk to human health and the environment. This paper presents the development of efficient carboneous nanofibrous membranes for NP filtration from aqueous solutions. Free-standing carbon nanofiber (CNF mats with different fiber size distribution ranging from 126 to 554 nm in diameter were produced by electrospinning of polyacrylonitrile (PAN precursor solution followed by thermal treatment. Moreover, tetraethoxyorthosilicate was added to provide flexibility and increase the specific surface area of the CNF. The resulting membranes are bendable and mechanically strong enough to withstand filtration under pressure or vacuum. The experimental results of filtration revealed that the fabricated membranes could efficiently reject nanoparticles of different types (Au, Ag, and TiO2 and size (from 10 to 100 nm in diameter from aqueous solutions. It is worth mentioning that the removal of Ag NP with diameters as small as 10 nm was close to 100% with an extremely high flux of 47620 L m−2 h−1 bar−1.

  7. Role of ITO nanoparticles embedded into electrospun ITO nanofibers

    Science.gov (United States)

    Yoon, Sangcheol; Kim, Hyebin; Cha, Seung-Jae; Shin, Eun-Sol; Noh, Yong-Young; Hong, Sung-Jei; Park, Byoungchoo; Hwang, Inchan

    2017-11-01

    Both crystallization and molecular density are significant to achieve high electrical conductivity of transparent electrodes. Herein, we investigated the embedding effects of indium tin oxide (ITO) nanoparticles (NPs) into ITO nanofibers (NFs) synthesized by utilizing an electrospinning technique from ITO precursor solutions. We found that the ITO NPs might act as nucleation seeds that initiate crystallization of ITO, evidenced by flake-like morphologies which cannot be observed without ITO NPs. XRD measurements reveal that the ITO is crystalline with a higher degree and the size of ITO crystallites increases in the presence of ITO NPs embedded into NFs. Embedding ITO NPs leads to the formation of short fibers, but there is still large space between fibers as they are vertically stacked in the films, resulting in low electrical conductivity. Interestingly, a high ratio of ITO NPs enhances the electrical conductivity, as compared to a low ratio, which we attribute to the high fiber density on substrates due to the formation of shorter ITO NFs. Our results highlight that the ITO NPs influence not only the ITO crystallization but also the lengths of NFs. High electrical conductivity of NF films can be obtained by a high degree of crystallization and the optimum NF length that reduces spaces between NFs in the films.

  8. Electrospun magnetically separable calcium ferrite nanofibers for photocatalytic water purification

    International Nuclear Information System (INIS)

    EL-Rafei, A.M.; El-Kalliny, Amer S.; Gad-Allah, Tarek A.

    2017-01-01

    Three-dimensional random calcium ferrite, CaFe 2 O 4 , nanofibers (NFs) were successfully prepared via the electrospinning method. The effect of calcination temperature on the characteristics of the as-spun NFs was investigated. X-ray diffraction analysis showed that CaFe 2 O 4 phase crystallized as a main phase at 700 °C and as a sole phase at 1000 °C. Field emission scanning electron microscopy emphasized that CaFe 2 O 4 NFs were fabricated with diameters in the range of 50–150 nm and each fiber was composed of 20–50 nm grains. Magnetic hysteresis loops revealed superparamagnetic behavior for the prepared NFs. These NFs produced active hydroxyl radicals under simulated solar light irradiation making them recommendable for photocatalysis applications in water purification. In the meantime, these NFs can be easily separated from the treated water by applying an external magnetic field. - Highlights: • Three-dimensional porous random CaFe 2 O 4 NFs were successfully produced via electrospinning method. • These NFs exhibited typical superparamagnetic behavior for the ferromagnetic materials. • The low band-gap energy of these NFs (~1.6 eV) allows them to absorb a wide range of the solar spectrum. • These NFs can produce the active • OH under solar light and can be recovered easily by applying an external magnetic field. • These NFs can be used solely as magnetically separable photocatalyst or as magnetic additive for another photocatalyst.

  9. Electrospun Polymer Nanofibers Reinforced by Tannic Acid/Fe+++ Complexes †

    Science.gov (United States)

    Yang, Weiqiao; Sousa, Ana M. M.; Thomas-Gahring, Audrey; Fan, Xuetong; Jin, Tony; Li, Xihong; Tomasula, Peggy M.; Liu, LinShu

    2016-01-01

    We report the successful preparation of reinforced electrospun nanofibers and fibrous mats of polyvinyl alcohol (PVA) via a simple and inexpensive method using stable tannic acid (TA) and ferric ion (Fe+++) assemblies formed by solution mixing and pH adjustment. Changes in solution pH change the number of TA galloyl groups attached to the Fe+++ from one (pH PVA and TA. At pH ~ 5.5, the morphology and fiber diameter size (FDS) examined by SEM are determinant for the mechanical properties of the fibrous mats and depend on the PVA content. At an optimal 8 wt % concentration, PVA becomes fully entangled and forms uniform nanofibers with smaller FDS (p mechanical properties when compared to mats of PVA alone and of PVA with TA (p mechanical properties (p 0.05) suggesting the potential of TA-Fe+++ assemblies to reinforce polymer nanofibers with high functionality for use in diverse applications including food, biomedical and pharmaceutical. PMID:28773876

  10. Transparent nanostructured electrodes: Electrospun NiO nanofibers/NiO films

    Energy Technology Data Exchange (ETDEWEB)

    Lamastra, F.R. [Italian Interuniversity Consortium on Materials Science and Technology (INSTM), Research Unit Roma Tor Vergata, Via del Politecnico 1, 00133 Rome (Italy); Nanni, F. [Italian Interuniversity Consortium on Materials Science and Technology (INSTM), Research Unit Roma Tor Vergata, Via del Politecnico 1, 00133 Rome (Italy); Department of Enterprise Engineering, University of Rome Tor Vergata, Via del Politecnico 1, 00133 Rome (Italy); Menchini, F. [ENEA, CR Casaccia, Via Anguillarese 301, 00123 Rome (Italy); Nunziante, P. [Italian Interuniversity Consortium on Materials Science and Technology (INSTM), Research Unit Roma Tor Vergata, Via del Politecnico 1, 00133 Rome (Italy); Department of Chemical Sciences and Technologies, University of Rome Tor Vergata, Via della Ricerca Scientifica 1, 00133 Rome (Italy); Grilli, M.L., E-mail: marialuisa.grilli@enea.it [ENEA, CR Casaccia, Via Anguillarese 301, 00123 Rome (Italy)

    2016-02-29

    Polyvinylpyrrolidone (PVP)/nickel(II) acetate precursor fibers were deposited by electrospinning directly on radio frequency sputtered thin Ni and NiO films grown on quartz substrate, starting from Ni(II) acetate and PVP solution in ethanol. The samples were calcined in air in the temperature range 400–500 °C to obtain transparent and conductive p-type NiO nanofibers on NiO films. A higher density of nanofibers was obtained on Ni/quartz substrates, as compared to NiO/quartz ones, demonstrating the feasibility of fiber adhesion directly to an insulating substrate previously coated by a thin Ni layer. Samples were characterized by field emission-scanning electron microscopy, X-ray diffraction, spectrophotometric and resistance measurements. - Highlights: • Nanostructured electrodes: electrospun NiO nanofibers/NiO films were fabricated. • NiO fibers were directly grown on insulating substrate coated by thin Ni or NiO films. • Good quality crystalline fibers were obtained at low calcination temperatures. • Transparent and conductive p-type electrodes were fabricated.

  11. Plasma Modification of Poly Lactic Acid Solutions to Generate High Quality Electrospun PLA Nanofibers.

    Science.gov (United States)

    Rezaei, Fatemeh; Nikiforov, Anton; Morent, Rino; De Geyter, Nathalie

    2018-02-02

    Physical properties of pre-electrospinning polymer solutions play a key role in electrospinning as they strongly determine the morphology of the obtained electrospun nanofibers. In this work, an atmospheric-pressure argon plasma directly submerged in the liquid-phase was used to modify the physical properties of poly lactic acid (PLA) spinning solutions in an effort to improve their electrospinnability. The electrical characteristics of the plasma were investigated by two methods; V-I waveforms and Q-V Lissajous plots while the optical emission characteristics of the plasma were also determined using optical emission spectroscopy (OES). To perform a complete physical characterization of the plasma-modified polymer solutions, measurements of viscosity, surface tension, and electrical conductivity were performed for various PLA concentrations, plasma exposure times, gas flow rates, and applied voltages. Moreover, a fast intensified charge-couple device (ICCD) camera was used to image the bubble dynamics during the plasma treatments. In addition, morphological changes of PLA nanofibers generated from plasma-treated PLA solutions were observed by scanning electron microscopy (SEM). The performed plasma treatments were found to induce significant changes to the main physical properties of the PLA solutions, leading to an enhancement of electrospinnability and an improvement of PLA nanofiber formation.

  12. FAS Grafted Electrospun Poly(vinyl alcohol) Nanofiber Membranes with Robust Superhydrophobicity for Membrane Distillation.

    Science.gov (United States)

    Dong, Zhe-Qin; Wang, Bao-Juan; Ma, Xiao-hua; Wei, Yong-Ming; Xu, Zhen-Liang

    2015-10-14

    This study develops a novel type of electrospun nanofiber membranes (ENMs) with high permeability and robust superhydrophobicity for membrane distillation (MD) process by mimicking the unique unitary microstructures of ramee leaves. The superhydrophobic ENMs were fabricated by the eletrospinning of poly(vinyl alcohol) (PVA), followed by chemical cross-linking with glutaraldehyde and surface modification via low surface energy fluoroalkylsilane (FAS). The resultant FAS grafted PVA (F-PVA) nanofiber membranes were endowed with self-cleaning properties with water contact angles of 158° and sliding angles of 4° via the modification process, while retaining their high porosities and interconnected open structures. For the first time, the robust superhydrophobicity of the ENMs for MD was confirmed by testing the F-PVA nanofiber membranes under violent ultrasonic treatment and harsh chemical conditions. Furthermore, vacuum membrane distillation experiments illustrated that the F-PVA membranes presented a high and stable permeate flux of 25.2 kg/m2 h, 70% higher than those of the commercial PTFE membranes, with satisfied permeate conductivity (<5 μm/cm) during a continuous test of 16 h (3.5 wt % NaCl as the feed solution, and feed temperature and permeate pressure were set as 333 K and 9 kPa, respectively), suggesting their great potentials in myriad MD processes such as high salinity water desalination and volatile organiccompounds removal.

  13. Electrospun Nanofibers Made of Silver Nanoparticles, Cellulose Nanocrystals, and Polyacrylonitrile as Substrates for Surface-Enhanced Raman Scattering

    Directory of Open Access Journals (Sweden)

    Suxia Ren

    2017-01-01

    Full Text Available Nanofibers with excellent activities in surface-enhanced Raman scattering (SERS were developed through electrospinning precursor suspensions consisting of polyacrylonitrile (PAN, silver nanoparticles (AgNPs, silicon nanoparticles (SiNPs, and cellulose nanocrystals (CNCs. Rheology of the precursor suspensions, and morphology, thermal properties, chemical structures, and SERS sensitivity of the nanofibers were investigated. The electrospun nanofibers showed uniform diameters with a smooth surface. Hydrofluoric (HF acid treatment of the PAN/CNC/Ag composite nanofibers (defined as p-PAN/CNC/Ag led to rougher fiber surfaces with certain pores and increased mean fiber diameters. X-ray diffraction (XRD and X-ray photoelectron spectroscopy (XPS results confirmed the existence of AgNPs that were formed during heat and HF acid treatment processes. In addition, thermal stability of the electrospun nanofibers increased due to the incorporation of CNCs and AgNPs. The p-PAN/CNC/Ag nanofibers were used as a SERS substrate to detect p-aminothiophenol (p-ATP probe molecule. The results show that this substrate exhibited high sensitivity for the p-ATP probe detection.

  14. Influence of the collector and heat treatment in the structure of BiFeO3 electrospun nanofibers

    International Nuclear Information System (INIS)

    Melo, G.H.F.; Santos, J.P.F.; Bretas, R.E.S.

    2016-01-01

    The objective of this work was to analyze the influence of the collector type and heat treatment on the morphology and crystalline phases of BiFeO 3 electrospun nanofibers. A solution containing (Fe(NO 3 ) 3.9 H 2 O and Bi(NO 3 ) 3.5 H 2 O) as precursors together with a polyvinylpyrrolidone solution was electrospun using 2.8KV/cm as electrical field. The collector type was however, changed (aluminum and glass). After the electrospinning, the as-spun nanofibers were submitted to two different heat treatments: one at 550°C and the other at 750°C, both during 2h. The collector type changed the morphology of the nanofibers; while in the glass collector, a non-woven mat of flat and rough nanofibers was obtained, in the aluminum collector, mats of circular and smooth nanofibers were obtained. The thermal treatment also changed the morphology and amount of crystalline phases; at 550°C, the nanofiber morphology was maintained and only one crystalline phase (BiFeO 3 ) was detected. On the other hand, at 750°C, flakes were obtained of two crystalline phases (BiFeO 3 and Bi 2 Fe 4 O 9 ). (author)

  15. Process Optimization and Emperical Modelling for Electrospun Polyacrylonitrile (PAN) Nanofiber Precursor of Carbon nanofibers

    NARCIS (Netherlands)

    Gu, S.Y.; Gu, S.; Ren, J.; Vancso, Gyula J.

    2005-01-01

    Ultrafine fibers were spun from polyacrylonitrile (PAN)/N,N-dimethyl formamide (DMF) solution as a precursor of carbon nanofibers using a homemade electrospinning set-up. Fibers with diameter ranging from 200 nm to 1200 nm were obtained. Morphology of fibers and distribution of fiber diameter were

  16. Aligned electrospun nanofibers as proton conductive channels through thickness of sulfonated poly (phthalazinone ether sulfone ketone) proton exchange membranes

    Science.gov (United States)

    Gong, Xue; He, Gaohong; Wu, Yao; Zhang, Shikai; Chen, Bo; Dai, Yan; Wu, Xuemei

    2017-08-01

    A novel approach is proposed to fabricate sulfonated poly (phthalazinone ether sulfone ketone) (SPPESK) proton exchange membranes with ordered through-plane electrospinning nanofibers, which provide nano-scale through-plane proton conductive channels along the thickness direction of the membranes, aiming to satisfy the challenging requirement of high through-plane proton conductivity in fuel cell operations. Induced by electrostatic attraction of strong electric field, the negatively charged sulfonic acid groups tend to aggregate towards surface of the electrospun fibers, which is evidenced by TEM and SAXS and further induces aggregation of the sulfonic acid groups in the SPPESK inferfiber voids filler along the surface of the nanofibers. The aligned electrospun nanofibers carries long-range ionic clusters along the thickness direction of the membrane and results in much higher total through-plane conductivity in the thickness aligned electrospun membranes, nearly twice as much as that of the cast SPPESK membrane. With smooth treatment, the thickness aligned electrospun SPPESK membranes exhibit higher single cell power density and tensile strength as compared with Nafion 115 (around 1.2 and 1.5 folds, respectively). Such a design of thickness aligned nano-size proton conductive channels provide feasibility for high performance non-fluorinated PEMs in fuel cell applications.

  17. Electrospun magnetically separable calcium ferrite nanofibers for photocatalytic water purification

    Energy Technology Data Exchange (ETDEWEB)

    EL-Rafei, A.M., E-mail: am.amin@nrc.sci.eg [Refractories, Ceramics and Building Materials Department, National Research Centre, 33 EL Bohouth St. (former EL Tahrir St.), P.O. 12622, Dokki, Giza (Egypt); El-Kalliny, Amer S.; Gad-Allah, Tarek A. [Water Pollution Research Department, National Research Centre, 33 EL Bohouth St. (former EL Tahrir St.), P.O. 12622, Dokki, Giza (Egypt)

    2017-04-15

    Three-dimensional random calcium ferrite, CaFe{sub 2}O{sub 4}, nanofibers (NFs) were successfully prepared via the electrospinning method. The effect of calcination temperature on the characteristics of the as-spun NFs was investigated. X-ray diffraction analysis showed that CaFe{sub 2}O{sub 4} phase crystallized as a main phase at 700 °C and as a sole phase at 1000 °C. Field emission scanning electron microscopy emphasized that CaFe{sub 2}O{sub 4} NFs were fabricated with diameters in the range of 50–150 nm and each fiber was composed of 20–50 nm grains. Magnetic hysteresis loops revealed superparamagnetic behavior for the prepared NFs. These NFs produced active hydroxyl radicals under simulated solar light irradiation making them recommendable for photocatalysis applications in water purification. In the meantime, these NFs can be easily separated from the treated water by applying an external magnetic field. - Highlights: • Three-dimensional porous random CaFe{sub 2}O{sub 4} NFs were successfully produced via electrospinning method. • These NFs exhibited typical superparamagnetic behavior for the ferromagnetic materials. • The low band-gap energy of these NFs (~1.6 eV) allows them to absorb a wide range of the solar spectrum. • These NFs can produce the active {sup •} OH under solar light and can be recovered easily by applying an external magnetic field. • These NFs can be used solely as magnetically separable photocatalyst or as magnetic additive for another photocatalyst.

  18. Delivery of multipurpose prevention drug combinations from electrospun nanofibers using composite microarchitectures

    Directory of Open Access Journals (Sweden)

    Blakney AK

    2014-06-01

    Full Text Available Anna K Blakney, Emily A Krogstad, Yonghou H Jiang, Kim A WoodrowDepartment of Bioengineering, University of Washington, Seattle, Washington, USABackground: Electrospun drug-eluting fabrics have enormous potential for the delivery of physicochemically diverse drugs in combination by controlling the underlying material chemistry and fabric microarchitecture. However, the rationale for formulating drugs at high drug loading in the same or separate fibers is unknown but has important implications for product development and clinical applications.Methods: Using a production-scale free-surface electrospinning instrument, we produced electrospun nanofibers with different microscale geometries for the co-delivery of tenofovir (TFV and levonorgestrel (LNG – two lead drug candidates for multipurpose prevention of HIV acquisition and unintended pregnancy. We investigated the in vitro drug release of TFV and LNG combinations from composites that deliver the two drugs from the same fiber (combined fibers or from separate fibers in a stacked or interwoven architecture. For stacked composites, we also examined the role that fabric thickness has on drug-release ­kinetics. We also measured the cytotoxicity and antiviral activity of the drugs delivered alone and in combination.Results: Herein, we report on the solution and processing parameters for the free-surface electrospinning of medical fabrics with controlled microarchitecture and high drug loading (up to 20 wt%. We observed that in vitro release of the highly water-soluble TFV, but not the water-insoluble LNG, was affected by composite microarchitecture, fabric thickness, and drug content. Finally, we showed that the drug-loaded nanofibers are noncytotoxic and that the antiviral activity of TFV is preserved through the electrospinning process and when combined with LNG.Conclusion: Electrospun fabrics with high drug loading create multicomponent systems that benefit from the independent control of the

  19. Preparation and Characterization of Soluble Eggshell Membrane Protein/PLGA Electrospun Nanofibers for Guided Tissue Regeneration Membrane

    Directory of Open Access Journals (Sweden)

    Jun Jia

    2012-01-01

    Full Text Available Guided tissue regeneration (GTR is a widely used method in periodontal therapy, which involves the placement of a barrier membrane to exclude migration of epithelium and ensure repopulation of periodontal ligament cells. The objective of this study is to prepare and evaluate a new type of soluble eggshell membrane protein (SEP/poly (lactic-co-glycolic acid (PLGA nanofibers using electrospinning method for GTR membrane application. SEP/PLGA nanofibers were successfully prepared with various blending ratios. The morphology, chemical composition, surface wettability, and mechanical properties of the nanofibers were characterized using scanning electron microscopy (SEM, contact angle measurement, Fourier transform-infrared spectroscopy (FTIR, and a universal testing machine. L-929 fibroblast cells were used to evaluate the biocompatibility of SEP/PLGA nanofibers and investigate the interaction between cells and nanofibers. Results showed that the SEP/PLGA electrospun membrane was composed of uniform, bead-free nanofibers, which formed an interconnected porous network structure. Mechanical property of SEP has been greatly improved by the addition of PLGA. The biological study results showed that SEP/PLGA nanofibers could enhance cell attachment, spreading, and proliferation. The study indicated the potential of SEP/PLGA nanofibers for GTR application and provided a basis for future optimization.

  20. Determining the mechanical properties of electrospun poly-ε-caprolactone (PCL) nanofibers using AFM and a novel fiber anchoring technique.

    Science.gov (United States)

    Baker, Stephen R; Banerjee, Soham; Bonin, Keith; Guthold, Martin

    2016-02-01

    Due to its low cost, biocompatibility and slow bioresorption, poly-ε-caprolactone (PCL) continues to be a suitable material for select biomedical engineering applications. We used a combined atomic force microscopy (AFM)/optical microscopy technique to determine key mechanical properties of individual electrospun PCL nanofibers with diameters between 440-1040nm. Compared to protein nanofibers, PCL nanofibers showed much lower adhesion, as they slipped on the substrate when mechanically manipulated. We, therefore, first developed a novel technique to anchor individual PCL nanofibers to micrometer-sized ridges on a substrate, and then mechanically tested anchored nanofibers. When held at constant strain, tensile stress relaxed with fast and slow relaxation times of 1.0±0.3s and 8.8±3.1s, respectively. The total tensile modulus was 62±26MPa, the elastic (non-relaxing) component of the tensile modulus was 53±36MPa. Individual PCL fibers could be stretched elastically (without permanent deformation) to strains of 19-23%. PCL nanofibers are rather extensible; they could be stretched to a strain of at least 98%, and a tensile strength of at least 12MPa, before they slipped off the AFM tip. PCL nanofibers that had aged for over a month at ambient conditions became stiffer and less elastic. Our technique provides accurate nanofiber mechanical data, which are needed to guide construction of scaffolds for cells and other biomedical devices. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

  1. Biomimetic synthesis of interlaced mesh structures TiO{sub 2} nanofibers with enhanced photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guanghui [Tianjin Key Laboratory of Applied Catalysis Science and Technology, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 China (China); Collaborative Innovation Center of Chemical Science and Engineering(Tianjin), Tianjin 300072 China (China); Zhang, Tianyong, E-mail: tyzhang@tju.edu.cn [Tianjin Key Laboratory of Applied Catalysis Science and Technology, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 China (China); Collaborative Innovation Center of Chemical Science and Engineering(Tianjin), Tianjin 300072 China (China); Li, Bin, E-mail: libin@tju.edu.cn [Tianjin Key Laboratory of Applied Catalysis Science and Technology, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 China (China); Collaborative Innovation Center of Chemical Science and Engineering(Tianjin), Tianjin 300072 China (China); Zhang, Xia; Chen, Xingwei [Tianjin Key Laboratory of Applied Catalysis Science and Technology, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072 China (China)

    2016-05-25

    A facile and economical method assisted by PPs (the spongy white peels of pomelo peel) was applied for preparing interlaced mesh structures TiO{sub 2} nanofibers by a liquid impregnation method followed by a calcination process in this study. And the as-prepared materials were comprehensively investigated by X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectra, UV-vis diffuse reflectance spectroscopy, photoluminescence spectra and N{sub 2} adsorption-desorption. The resultant TiO{sub 2} materials exhibit unique morphology, in which the curly nanofibers with the diameter about 90 nm interweave each other for assembling hierarchical mesh structures and there are abundant grooves on the surface of the nanofibers. During the bio-inspired synthetic process, the PPs play important roles as template and induction for forming the hierarchical mesh structures of TiO{sub 2} nanofibers. Furthermore, some of the as-prepared TiO{sub 2} samples exhibit 99% degradation rate for methyl orange in 30 min under UV light irradiation, which can be ascribed to the larger surface area and the unique hierarchical mesh structures. In addition, the stability tests of 5 cycling runs of the photocatalysts indicate that the as-prepared TiO{sub 2} nanofibers can be applied as a practical photocatalyst for degrading organic dyes under UV light irradiation. Therefore, hopefully, the strategy for preparing the TiO{sub 2} nanofibers can be extended to design many more powerful photocatalysts for the environmental remediation in the near future. - Graphical abstract: The TiO{sub 2} nanofibers with interlaced mesh structures were prepared with PPs (the spongy white peels of pomelo peel) as the reactive substrate and directing template, and titanium tetrachloride (TiCl{sub 4}) as titanium resource. And the as-prepared TiO{sub 2} samples exhibit highly photocatalytic activity and good stability for degrading methyl orange under UV light irradiation. - Highlights: • A

  2. Hyperbranched-polyol-tethered poly (amic acid) electrospun nanofiber membrane with ultrahigh adsorption capacity for boron removal

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhe; Wu, Zhongyu; Zhang, Yufeng; Meng, Jianqiang, E-mail: jianqiang.meng@hotmail.com

    2017-04-30

    Highlights: • Electrospun nanofiber membranes were grafted with hyperbranched polyols. • The membrane had a maximum boron uptake of 5.68 mmol/g. • The membrane could adsorb 0.82 mmol/g boron from a 5 mg/L solution in 15 min. • The membrane obeyed the Langmuir and the pseudo-first-order kinetic model. • The regeneration efficiency remained over 90% after 10 cycled uses. - Abstract: The development of efficient adsorbents with high sorption capacity remains as a challenge for the removal of micropollutants occurred globally in water resources. In this work, poly (amic acid) (PAA) electrospun nanofiber membranes grafted with hyperbranched polyols were synthesized and used for boron removal. The PAA nanofiber was reacted with hyperbranched polyethylenimine (HPEI) and further with glycidol to introduce the vicinal hydroxyl groups. The chemical composition and surface characteristics of the obtained PAA-g-PG membranes were evaluated by FESEM, FTIR, XPS and water contact angles (WCA) measurements. The boron adsorption thermodynamics and kinetics were investigated systematically. The results showed that the PAA nanofiber spun from concentration of 15% had uniform morphology and narrow diameter distribution. The PAA-g-PG nanofiber membrane had a maximum boron uptake of 5.68 mmol/g and could adsorb 0.82 mmol/g boron from a 5 mg/L solution in 15 min. Both the high surface area of nanofibers and the hyperbranched structure should contribute to the high boron uptake and high adsorption rate. The nanofiber membrane obeyed the Langmuir adsorption model and the pseudo-first-order kinetic model. The regeneration efficiency of the nanofiber membrane remained 93.9% after 10 cycled uses, indicating good regenerability of the membrane.

  3. Electrospun Poly(ɛ-caprolactone) Composite Nanofibers with Controlled Release of Cis-Diamminediiodoplatinum for a Higher Anticancer Activity

    Science.gov (United States)

    Mu, Chaojing; Wu, Qingsheng

    2017-04-01

    Poly(ɛ-caprolactone) (PCL) nanofibers were prepared by electrospun, on which the cis-diamminediiodoplatinum ( cis-DIDP) was loaded, cis-DIDP@PCL, which effectively overcame cis-DIDP from dissociation or premature interaction with other bimolecular groups. Meanwhile, the toxicity and cross-resistance of cis-DIDP were reduced greatly. In vitro, cis-DIDP released from the PCL nanofibers eradicated the tumor cells around twice times more than free cis-DIDP, even better than cisplatin. Furthermore, cis-DIDP@PCL could controllably release cis-DIDP in different sustained-release solution based on our experiment.

  4. Effects of pre- and post-electrospinning plasma treatments on electrospun PCL nanofibers to improve cell interactions

    International Nuclear Information System (INIS)

    Asadian, M; Grande, S; Morent, R; Nikiforov, A; De Geyter, N; Declercq, H

    2017-01-01

    In this study, liquid plasma treatment was used to improve the morphology of Poly-ε-CaproLactone (PCL) NanoFibers (NFs), followed by performing a Dielectric Barrier Discharge (DBD) plasma surface modification to enhance the hydrophilicity of electrospun mats generated from plasma-modified PCL solutions. Cell interaction studies performed after 1 day and 7 days clearly revealed the highly increased cellular interactions on the double plasma-treated nanofibers compared to the pristine ones due to the combination of (1) a better NF morphology and (2) an increased surface hydrophilicity. (paper)

  5. Biodegradable electrospun nanofibers coated with platelet-rich plasma for cell adhesion and proliferation

    Energy Technology Data Exchange (ETDEWEB)

    Diaz-Gomez, Luis [Departamento de Farmacia y Tecnología Farmacéutica, Facultad de Farmacia, Universidad de Santiago de Compostela, 15872 Santiago de Compostela (Spain); Instituto de Ortopedia y Banco de Tejidos Musculoesqueléticos, Universidad de Santiago de Compostela, 15872 Santiago de Compostela (Spain); Alvarez-Lorenzo, Carmen, E-mail: carmen.alvarez.lorenzo@usc.es [Departamento de Farmacia y Tecnología Farmacéutica, Facultad de Farmacia, Universidad de Santiago de Compostela, 15872 Santiago de Compostela (Spain); Concheiro, Angel [Departamento de Farmacia y Tecnología Farmacéutica, Facultad de Farmacia, Universidad de Santiago de Compostela, 15872 Santiago de Compostela (Spain); Silva, Maite [Instituto de Ortopedia y Banco de Tejidos Musculoesqueléticos, Universidad de Santiago de Compostela, 15872 Santiago de Compostela (Spain); Dominguez, Fernando [Fundación Publica Galega de Medicina Xenómica, Santiago de Compostela (Spain); Sheikh, Faheem A.; Cantu, Travis; Desai, Raj; Garcia, Vanessa L. [Department of Chemistry, University of Texas Pan American, Edinburg, TX 78541 (United States); Macossay, Javier, E-mail: jmacossay@utpa.edu [Department of Chemistry, University of Texas Pan American, Edinburg, TX 78541 (United States)

    2014-07-01

    Biodegradable electrospun poly(ε-caprolactone) (PCL) scaffolds were coated with platelet-rich plasma (PRP) to improve cell adhesion and proliferation. PRP was obtained from human buffy coat, and tested on human adipose-derived mesenchymal stem cells (MSCs) to confirm cell proliferation and cytocompatibility. Then, PRP was adsorbed on the PCL scaffolds via lyophilization, which resulted in a uniform sponge-like coating of 2.85 (S.D. 0.14) mg/mg. The scaffolds were evaluated regarding mechanical properties (Young's modulus, tensile stress and tensile strain), sustained release of total protein and growth factors (PDGF-BB, TGF-β1 and VEGF), and hemocompatibility. MSC seeded on the PRP–PCL nanofibers showed an increased adhesion and proliferation compared to pristine PCL fibers. Moreover, the adsorbed PRP enabled angiogenesis features observed as neovascularization in a chicken chorioallantoic membrane (CAM) model. Overall, these results suggest that PRP–PCL scaffolds hold promise for tissue regeneration applications. - Highlights: • Platelet-rich plasma (PRP) can be adsorbed on electrospun fibers via lyophilization. • PRP coating enhanced mesenchymal stem cell adhesion and proliferation on scaffolds. • PRP-coated scaffolds showed sustained release of growth factors. • Adsorbed PRP provided angiogenic features. • PRP-poly(ε-caprolactone) scaffolds hold promise for tissue regeneration applications.

  6. Biodegradable electrospun nanofibers coated with platelet-rich plasma for cell adhesion and proliferation

    International Nuclear Information System (INIS)

    Diaz-Gomez, Luis; Alvarez-Lorenzo, Carmen; Concheiro, Angel; Silva, Maite; Dominguez, Fernando; Sheikh, Faheem A.; Cantu, Travis; Desai, Raj; Garcia, Vanessa L.; Macossay, Javier

    2014-01-01

    Biodegradable electrospun poly(ε-caprolactone) (PCL) scaffolds were coated with platelet-rich plasma (PRP) to improve cell adhesion and proliferation. PRP was obtained from human buffy coat, and tested on human adipose-derived mesenchymal stem cells (MSCs) to confirm cell proliferation and cytocompatibility. Then, PRP was adsorbed on the PCL scaffolds via lyophilization, which resulted in a uniform sponge-like coating of 2.85 (S.D. 0.14) mg/mg. The scaffolds were evaluated regarding mechanical properties (Young's modulus, tensile stress and tensile strain), sustained release of total protein and growth factors (PDGF-BB, TGF-β1 and VEGF), and hemocompatibility. MSC seeded on the PRP–PCL nanofibers showed an increased adhesion and proliferation compared to pristine PCL fibers. Moreover, the adsorbed PRP enabled angiogenesis features observed as neovascularization in a chicken chorioallantoic membrane (CAM) model. Overall, these results suggest that PRP–PCL scaffolds hold promise for tissue regeneration applications. - Highlights: • Platelet-rich plasma (PRP) can be adsorbed on electrospun fibers via lyophilization. • PRP coating enhanced mesenchymal stem cell adhesion and proliferation on scaffolds. • PRP-coated scaffolds showed sustained release of growth factors. • Adsorbed PRP provided angiogenic features. • PRP-poly(ε-caprolactone) scaffolds hold promise for tissue regeneration applications

  7. Fe-aminoclay-entrapping electrospun polyacrylonitrile nanofibers (FeAC-PAN NFs) for environmental engineering applications

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jae Young [Korea Railroad Research Institute, Uiwang (Korea, Republic of); Choi, Saehae [Korea Research Institute of Bioscience and Biotechnology, Daejeon (Korea, Republic of); Park, Seung Bin [KAIST, Daejeon (Korea, Republic of); Kim, Mooon Il; Lee, Young Chul [Gachon Univ., Seongnam (Korea, Republic of); Lee, Go Woon [KIER, Daejeon (Korea, Republic of); Lee, Hyun Uk [Korea Basic Science Institute, Daejeon (Korea, Republic of)

    2015-09-15

    Electrospun polyacrylonitrile nanofibers (PAN NFs) with entrapped water-soluble Fe-aminoclay (FeAC) [FeAC-PAN NFs] were prepared. Slow dropwise addition of water-soluble FeAC into a PAN solution, less aggregated of FeAC into electrospun PAN NFs was one-pot evolved without FeAC post-decoration onto as-prepared PAN NFs. Taking into consideration both the Fe{sup 3+} source in FeAC and the improved surface hydrophilicity, the feasibility of Fentonlike reaction for decolorization of cationic model dye methylene blue (MB) under 6 hrs UV-light irradiation was established. In the case where FeAC-PAN NFs were enhanced by hydrogen peroxide (H{sub 2}O{sub 2}) injection, the apparent kinetic reaction rates were increased relative to those for the PAN NFs. Thus, our flexible FeAC-PAN NF mats can be effectively utilized in water/waste treatment and other environmental engineering applications.

  8. A novel shortened electrospun nanofiber modified with a 'concentrated' polymer brush

    International Nuclear Information System (INIS)

    Yoshikawa, Chiaki; Zhang, Kun; Zawadzak, Ewelina; Kobayashi, Hisatoshi

    2011-01-01

    We report the fabrication of shortened electrospun polymer fibers with a well-defined concentrated polymer brush. We first prepared electrospun nanofibers from a random copolymer of styrene and 4-vinylbenzyl 2-bromopropionate, with number-average molecular weight M n =105 200 and weight-average molecular weight M w =296 700 (M w /M n =2.82). The fibers had a diameter of 593±74 nm and contained initiating sites for surface-initiated atom transfer radical polymerization (SI-ATRP). Then, SI-ATRP of hydrophilic styrene sodium sulfonate (SSNa) was carried out in the presence of a free initiator and the hydrophobic fibers. Gel permeation chromatography confirmed that M n and M w /M n values were almost the same for free polymers and graft polymers. M n agreed well with the theoretical prediction, and M w /M n was relatively low ( n , we calculated the graft density σ as 0.22 chains nm -2 . This value was nearly equal to the density obtained on silicon wafers (σ=0.24 chains nm -2 ), which is categorized into the concentrated brush regime. Finally, we mechanically cut the fibers with a concentrated poly(SSNa) brush by a homogenizer. With increasing cutting time, the fiber length became shorter and more homogenous (11±17 μm after 3 h). The shortened fibers exhibited excellent water dispersibility owing to the hydrophilic poly(SSNa) brush layer.

  9. Novel electrospun nanofibers of modified gelatin-tyrosine in cartilage tissue engineering

    International Nuclear Information System (INIS)

    Agheb, Maria; Dinari, Mohammad; Rafienia, Mohammad; Salehi, Hossein

    2017-01-01

    In natural cartilage tissues, chondrocytes are linked to extracellular matrix (ECM) through cell-surface binding proteins. Surface modification of gelatin can provide a new generation of biopolymers and fibrous scaffolds with chemical, mechanical, and biological properties. In this study tyrosine protein and 1,2,3-triazole ring were utilized to functionalize gelatin without Cu catalyst. Their molecular structure was characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy ( 1 HNMR). Chemical cross-linkers such as glutaraldehyde (GA) and 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC)/N-hydroxysulfosuccinimide (NHS) were used to electrospin the modified gelatin. The modification of gelatin and cross-linking effects were confirmed by scanning electron microscopy (SEM), contact angle measurement, and mechanical tests. MTT assay using chondrocyte cells showed cell viability of electrospun modified gelatin scaffolds. In vitro cell culture studies showed that electrospun engineered protein scaffolds would support the attachment and growth of cells. The results also showed that cross-linked nanofibers with EDC/NHS could be considered excellent matrices in cell adhesion and proliferation before electrospinning process and their potential substrate in tissue engineering applications, especially in the field of cartilage engineering.

  10. Surface modification of electrospun PVA/chitosan nanofibers by dielectric barrier discharge plasma at atmospheric pressure and studies of their mechanical properties and biocompatibility.

    Science.gov (United States)

    Das, Punamshree; Ojah, Namita; Kandimalla, Raghuram; Mohan, Kiranjyoti; Gogoi, Dolly; Dolui, Swapan Kumar; Choudhury, Arup Jyoti

    2018-03-22

    In this paper, surface of electrospun PVA/Cs nanofibers is modified using dielectric barrier discharge (DBD) plasma and the relationship between the observed mechanical properties and biocompatibility of the nanofibers and plasma-induced surface properties is discussed. Plasma treatment of electrospun PVA/Cs nanofibers is carried out with both inert (argon, Ar) and reactive (oxygen, O 2 ) gases at atmospheric pressure. Incorporation of oxygen-containing polar functional groups on the surface of Ar-plasma treated (PVA/Cs/Ar) and O 2 -plasma treated (PVA/Cs/O 2 ) nanofibers and increase in surface roughness contribute to the improvement of surface wettability and the decrease of contact angle with water of the nanofibers. Both PVA/Cs/Ar and PVA/Cs/O 2 nanofibers show high tensile strength (11.6-15.6%) and Young's modulus (33.8-37.3%) as compared to the untreated one. Experimental results show that in terms of haemolytic activity the PVA/Cs/Ar and PVA/Cs/O 2 nanofibers do not cause structural changes of blood cells and meet the biocompatibility requirements for blood-contacting polymeric materials. MTT cell viability results further reveals improvement in biocompatibility of PVA/Cs nanofibers after Ar and O 2 plasma treatment. The results suggest that DBD plasma treated electrospun PVA/Cs nanofibers have the potential to be used as wound dressing and scaffolds for tissue engineering. Copyright © 2018 Elsevier B.V. All rights reserved.

  11. Hyperbranched-polyol-tethered poly (amic acid) electrospun nanofiber membrane with ultrahigh adsorption capacity for boron removal

    Science.gov (United States)

    Wang, Zhe; Wu, Zhongyu; Zhang, Yufeng; Meng, Jianqiang

    2017-04-01

    The development of efficient adsorbents with high sorption capacity remains as a challenge for the removal of micropollutants occurred globally in water resources. In this work, poly (amic acid) (PAA) electrospun nanofiber membranes grafted with hyperbranched polyols were synthesized and used for boron removal. The PAA nanofiber was reacted with hyperbranched polyethylenimine (HPEI) and further with glycidol to introduce the vicinal hydroxyl groups. The chemical composition and surface characteristics of the obtained PAA-g-PG membranes were evaluated by FESEM, FTIR, XPS and water contact angles (WCA) measurements. The boron adsorption thermodynamics and kinetics were investigated systematically. The results showed that the PAA nanofiber spun from concentration of 15% had uniform morphology and narrow diameter distribution. The PAA-g-PG nanofiber membrane had a maximum boron uptake of 5.68 mmol/g and could adsorb 0.82 mmol/g boron from a 5 mg/L solution in 15 min. Both the high surface area of nanofibers and the hyperbranched structure should contribute to the high boron uptake and high adsorption rate. The nanofiber membrane obeyed the Langmuir adsorption model and the pseudo-first-order kinetic model. The regeneration efficiency of the nanofiber membrane remained 93.9% after 10 cycled uses, indicating good regenerability of the membrane.

  12. Antitumor Activity of Doxorubicin-Loaded Carbon Nanotubes Incorporated Poly(Lactic-Co-Glycolic Acid) Electrospun Composite Nanofibers

    Science.gov (United States)

    Yu, Yuan; Kong, Lijun; Li, Lan; Li, Naie; Yan, Peng

    2015-08-01

    The drug-loaded composite electrospun nanofiber has attracted more attention in biomedical field, especially in cancer therapy. In this study, a composite nanofiber was fabricated by electrospinning for cancer treatment. Firstly, the carbon nanotubes (CNTs) were selected as carriers to load the anticancer drug—doxorubicin (DOX) hydrochloride. Secondly, the DOX-loaded CNTs (DOX@CNTs) were incorporated into the poly(lactic-co-glycolic acid) (PLGA) nanofibers via electrospinning. Finally, a new drug-loaded nanofibrous scaffold (PLGA/DOX@CNTs) was formed. The properties of the prepared composite nanofibrous mats were characterized by various techniques. The release profiles of the different DOX-loaded nanofibers were measured, and the in vitro antitumor efficacy against HeLa cells was also evaluated. The results showed that DOX-loaded CNTs can be readily incorporated into the nanofibers with relatively uniform distribution within the nanofibers. More importantly, the drug from the composite nanofibers can be released in a sustained and prolonged manner, and thereby, a significant antitumor efficacy in vitro is obtained. Thus, the prepared composite nanofibrous mats are a promising alternative for cancer treatment.

  13. Air filter devices including nonwoven meshes of electrospun recombinant spider silk proteins.

    Science.gov (United States)

    Lang, Gregor; Jokisch, Stephan; Scheibel, Thomas

    2013-05-08

    Based on the natural sequence of Araneus diadematus Fibroin 4 (ADF4), the recombinant spider silk protein eADF4(C16) has been engineered. This highly repetitive protein has a molecular weight of 48kDa and is soluble in different solvents (hexafluoroisopropanol (HFIP), formic acid and aqueous buffers). eADF4(C16) provides a high potential for various technical applications when processed into morphologies such as films, capsules, particles, hydrogels, coatings, fibers and nonwoven meshes. Due to their chemical stability and controlled morphology, the latter can be used to improve filter materials. In this protocol, we present a procedure to enhance the efficiency of different air filter devices, by deposition of nonwoven meshes of electrospun recombinant spider silk proteins. Electrospinning of eADF4(C16) dissolved in HFIP results in smooth fibers. Variation of the protein concentration (5-25% w/v) results in different fiber diameters (80-1,100 nm) and thus pore sizes of the nonwoven mesh. Post-treatment of eADF4(C16) electrospun from HFIP is necessary since the protein displays a predominantly α-helical secondary structure in freshly spun fibers, and therefore the fibers are water soluble. Subsequent treatment with ethanol vapor induces formation of water resistant, stable β-sheet structures, preserving the morphology of the silk fibers and meshes. Secondary structure analysis was performed using Fourier transform infrared spectroscopy (FTIR) and subsequent Fourier self-deconvolution (FSD). The primary goal was to improve the filter efficiency of existing filter substrates by adding silk nonwoven layers on top. To evaluate the influence of electrospinning duration and thus nonwoven layer thickness on the filter efficiency, we performed air permeability tests in combination with particle deposition measurements. The experiments were carried out according to standard protocols.

  14. Air Filter Devices Including Nonwoven Meshes of Electrospun Recombinant Spider Silk Proteins

    Science.gov (United States)

    Lang, Gregor; Jokisch, Stephan; Scheibel, Thomas

    2013-01-01

    Based on the natural sequence of Araneus diadematus Fibroin 4 (ADF4), the recombinant spider silk protein eADF4(C16) has been engineered. This highly repetitive protein has a molecular weight of 48kDa and is soluble in different solvents (hexafluoroisopropanol (HFIP), formic acid and aqueous buffers). eADF4(C16) provides a high potential for various technical applications when processed into morphologies such as films, capsules, particles, hydrogels, coatings, fibers and nonwoven meshes. Due to their chemical stability and controlled morphology, the latter can be used to improve filter materials. In this protocol, we present a procedure to enhance the efficiency of different air filter devices, by deposition of nonwoven meshes of electrospun recombinant spider silk proteins. Electrospinning of eADF4(C16) dissolved in HFIP results in smooth fibers. Variation of the protein concentration (5-25% w/v) results in different fiber diameters (80-1,100 nm) and thus pore sizes of the nonwoven mesh. Post-treatment of eADF4(C16) electrospun from HFIP is necessary since the protein displays a predominantly α-helical secondary structure in freshly spun fibers, and therefore the fibers are water soluble. Subsequent treatment with ethanol vapor induces formation of water resistant, stable β-sheet structures, preserving the morphology of the silk fibers and meshes. Secondary structure analysis was performed using Fourier transform infrared spectroscopy (FTIR) and subsequent Fourier self-deconvolution (FSD). The primary goal was to improve the filter efficiency of existing filter substrates by adding silk nonwoven layers on top. To evaluate the influence of electrospinning duration and thus nonwoven layer thickness on the filter efficiency, we performed air permeability tests in combination with particle deposition measurements. The experiments were carried out according to standard protocols. PMID:23685883

  15. Fluorescent Nanocomposite of Embedded Ceria Nanoparticles in Crosslinked PVA Electrospun Nanofibers

    Directory of Open Access Journals (Sweden)

    Nader Shehata

    2016-06-01

    Full Text Available This paper introduces a new fluorescent nanocomposite of electrospun biodegradable nanofibers embedded with optical nanoparticles. In detail, this work introduces the fluorescence properties of PVA nanofibers generated by the electrospinning technique with embedded cerium oxide (ceria nanoparticles. Under near-ultra violet excitation, the synthesized nanocomposite generates a visible fluorescent emission at 520 nm, varying its intensity peak according to the concentration of in situ embedded ceria nanoparticles. This is due to the fact that the embedded ceria nanoparticles have optical tri-valiant cerium ions, associated with formed oxygen vacancies, with a direct allowed bandgap around 3.5 eV. In addition, the impact of chemical crosslinking of the PVA on the fluorescence emission is studied in both cases of adding ceria nanoparticles in situ or of a post-synthesis addition via a spin-coating mechanism. Other optical and structural characteristics such as absorbance dispersion, direct bandgap, FTIR spectroscopy, and SEM analysis are presented. The synthesized optical nanocomposite could be helpful in different applications such as environmental monitoring and bioimaging.

  16. The effect of electrospun nanofibers alignment on the synthesis of one-dimensional silicon carbide nanostructure

    Science.gov (United States)

    Hooshyar, Ali; Kokabi, Mehrdad

    2018-01-01

    One-dimensional silicon carbide (1D SiC) nanostructure has shown unusual properties such as extremely high strength, good flexibility, fracture toughness, wide band gap ( 3.2eV), large breakdown electric field strength (>2 MV cm-1, 10 times that of silicon), and inverse Hall-Petch effect. Because of these advantages, 1D SiC nanomaterial has gained extensive attention on the wide range of applications in microelectronics, optoelectronics, nanocomposites, and catalyst supports. Many methods have been used for the synthesis of 1D SiC nanostructures such as chemical vapor deposition, carbon nanotube-confined reaction, laser ablation, high-frequency induction heating, and arc discharge. However, these methods have also some shortcomings such as using catalyst, high-cost, low yield, irregular geometry and impurity. In this work, electrospinning was used to prepare aligned PVA/SiO2 composite nanofibers and the effect of fiber alignment on the production efficiency and quality of 1D SiC nanostructure was investigated. For this purpose, aligned electrospun nanofibers, as the desirable precursor, were put in a tube furnace and heated up to 1250°C under a controlled program in an inert atmosphere. Finally, the grown 1D SiC nanostructure product was characterized using SEM, XRD, and FTIR. The results confirmed the successful synthesis of pure crystalline1D β-SiC nanostructure with high yield, more regular, and metal catalyst-free.

  17. Electrospun polymethylacrylate nanofibers membranes for quasi-solid-state dye sensitized solar cells

    Directory of Open Access Journals (Sweden)

    M. Fathy

    2016-06-01

    Full Text Available Polymethylacrylate (PMA nanofibers membranes are fabricated by electrospinning technique and applied to the polymer matrix in quasi-solid-state electrolytes for dye sensitized solar cells (DSSCs. There is no previous studies reporting the production of PMA nanofibers. The electrospinning parameters such as polymer concentration, applied voltage, feed rate, tip to collector distance and solvent were optimized. Electrospun PMA fibrous membrane with average fiber diameter of 350 nm was prepared from a 10 wt% solution of PMA in a mixture of acetone/N,N-dimethylacetamide (6:4 v/v at an applied voltage of 20 kV. It was then activated by immersing it in 0.5 M LiI, 0.05 M I2, and 0.5 M 4-tert-butylpyridine in 3-methoxyproponitrile to obtain the corresponding membrane electrolyte with an ionic conductivity of 2.4 × 10−3 S cm−1 at 25 °C. Dye sensitized solar cells (DSSCs employing the quasi solid-state electrolyte have an open-circuit voltage (Voc of 0.65 V and a short circuit current (Jsc of 6.5 mA cm−2 and photoelectric energy conversion efficiency (η of 1.4% at an incident light intensity of 100 mW cm−2.

  18. Electrospun sulfonated poly(ether ketone) nanofibers as proton conductive reinforcement for durable Nafion composite membranes

    Science.gov (United States)

    Klose, Carolin; Breitwieser, Matthias; Vierrath, Severin; Klingele, Matthias; Cho, Hyeongrae; Büchler, Andreas; Kerres, Jochen; Thiele, Simon

    2017-09-01

    We show that the combination of direct membrane deposition with proton conductive nanofiber reinforcement yields highly durable and high power density fuel cells. Sulfonated poly(ether ketone) (SPEK) was directly electrospun onto gas diffusion electrodes and then filled with Nafion by inkjet-printing resulting in a 12 μm thin membrane. The ionic membrane resistance (30 mΩ*cm2) was well below that of a directly deposited membrane reinforced with chemically inert (PVDF-HFP) nanofibers (47 mΩ*cm2) of comparable thickness. The power density of the fuel cell with SPEK reinforced membrane (2.04 W/cm2) is 30% higher than that of the PVDF-HFP reinforced reference sample (1.57 W/cm2). During humidity cycling and open circuit voltage (OCV) hold, the SPEK reinforced Nafion membrane showed no measurable degradation in terms of H2 crossover current density, thus fulfilling the target of 2 mA/cm2 of the DOE after degradation. The chemical accelerated stress test (100 h OCV hold at 90 °C, 30% RH, H2/air, 50/50 kPa) revealed a degradation rate of about 0.8 mV/h for the fuel cell with SPEK reinforced membrane, compared to 1.0 mV/h for the PVDF-HFP reinforced membrane.

  19. Preparation and Characterization of Electro-Spun Fabricated Ag-TiO2 Composite Nanofibers and Its Enhanced Photo-Catalytic Activity for the Degradation of Congo Red.

    Science.gov (United States)

    Jadhav, Arvind H; Zhang, Hongliang; Agyemang, Frank O; Hiremath, Vishwanath; Lee, Kyuyoung; Chandradass, Jeyaseelan; Seo, Jeong Gil; Kim, Hern

    2015-10-01

    Electro-spun fabricated TiO2 nanofibers were prepared by simple electro-spinning method, in subsequent step silver (Ag) was deposited using precipitation method and obtained Ag-TiO2 composite nanofibers. The properties and morphology of these prepared composite nanofibers were characterized by XRD, SEM, EDX, and TGA. The prepared electro-spun composite nanofibers were applied as catalyst for the photodegradation of Congo-red under immited solar light in aqueous solution. Result reveals that, Ag loaded TiO2 composite nanofibers were effectively increased photodegradation of Congo red compared with pure TiO2 nanofibers in analogous condition. As a result, 92.0% decomposition of Congo red was obtained by using 5 wt% of Ag loaded TiO2 composite nanofibers at room temperature in short reaction time using 300 W of solar light. In addition, photodegradation of Congo red was also studied under different experimental conditions such as amount of Ag loaded in TiO2 nanofibers and contact time. Moreover, we also studied sintering effect on TiO2 nanofibers and their consequent effect on photodegradation reaction. After completion of reaction, the nanofibers can be easily separated by filtration process and reused several times without significant loss of activity. Overall study reveals that, Ag-TiO2 composite nanofibers were strongly enhanced the surface activity for the photo catalytic degradation of Congo red under ambient condition.

  20. Electrospun nanofiber sheets incorporating methylcobalamin promote nerve regeneration and functional recovery in a rat sciatic nerve crush injury model.

    Science.gov (United States)

    Suzuki, Koji; Tanaka, Hiroyuki; Ebara, Mitsuhiro; Uto, Koichiro; Matsuoka, Hozo; Nishimoto, Shunsuke; Okada, Kiyoshi; Murase, Tsuyoshi; Yoshikawa, Hideki

    2017-04-15

    Peripheral nerve injury is one of common traumas. Although injured peripheral nerves have the capacity to regenerate, axon regeneration proceeds slowly and functional outcomes are often poor. Pharmacological enhancement of regeneration can play an important role in increasing functional recovery. In this study, we developed a novel electrospun nanofiber sheet incorporating methylcobalamin (MeCbl), one of the active forms of vitamin B12 homologues, to deliver it enough locally to the peripheral nerve injury site. We evaluated whether local administration of MeCbl at the nerve injury site was effective in promoting nerve regeneration. Electrospun nanofiber sheets gradually released MeCbl for at least 8weeks when tested in vitro. There was no adverse effect of nanofiber sheets on function in vivo of the peripheral nervous system. Local implantation of nanofiber sheets incorporating MeCbl contributed to the recovery of the motor and sensory function, the recovery of nerve conduction velocity, and the promotion of myelination after sciatic nerve injury, without affecting plasma concentration of MeCbl. Methylcobalamin (MeCbl) is a vitamin B12 analog and we previously reported its effectiveness in axonal outgrowth of neurons and differentiation of Schwann cells both in vitro and in vivo. Here we estimated the effect of local administered MeCbl with an electrospun nanofiber sheet on peripheral nerve injury. Local administration of MeCbl promoted functional recovery in a rat sciatic nerve crush injury model. These sheets are useful for nerve injury in continuity differently from artificial nerve conduits, which are useful only for nerve defects. We believe that the findings of this study are relevant to the scope of your journal and will be of interest to its readership. Copyright © 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  1. Silver nanoparticles immobilized onto polycaprolactone (PCL)/poly[2-(dimethylamino)ethyl metacrilate) nanofiber meshes

    International Nuclear Information System (INIS)

    Santos, Fernanda G.; Bonkovoski, Leticia C.; Witt, Maria A.; Rubira, Adley F.; Muniz, Edvani C.

    2015-01-01

    The present work comprises the fabrication of nanofiber meshes of polycaprolactone (PCL)/poly [(2-dimethylamino) ethyl methacrylate] (PDMAEMA) and the subsequent immobilization of silver nanoparticles, in order to obtain materials with potential application in tissue engineering. The nanofibers composed of different ratios of PDMAEMA / PCL (m/m) were obtained by electrospinning. These nanofiber meshes were then immersed in colloidal suspensions containing the AgNPs under different pH values to immobilize the nanoparticles onto the fiber's surface. A greater amount of AgNPs was deposited when the fibers were immersed in a solution of pH 5, as one can observe from the scanning electron microscopy (SEM) images and the X-ray spectroscopy (EDS) spectra. It was observed that the meshes of the blends suffered morphological changes after immersion in acid solution (pH 5), and, the deposition of AgNPs onto the meshes in general was more effective in acid environment (pH 5). (author)

  2. Improved thermostable polyvinyl alcohol electrospun nanofibers with entangled naringinase used in a novel mini-packed bed reactor.

    Science.gov (United States)

    Nunes, Mário A P; Martins, Samuel; Rosa, M Emilia; Gois, Pedro M P; Fernandes, Pedro C B; Ribeiro, Maria H L

    2016-08-01

    Polyvinyl alcohol (PVA) electrospun nanofibers were produced using an electrospinning technique. Key parameters (e.g. collectors, distance from needle tip to collector, among others) that influence the structure and morphology of fibers were optimized. The naringinase entrapped in PVA nanofibers retained over 100% of its initial activity after 212h of operation, at 25°C. Chemical crosslinking with several boronic acids further increased the hydrolysis temperature (up to 85°C) and yielded nanofibers with thermal stability up to 121°C. A mini packed bed reactor (PBR) developed to establish the feasibility for continuous enzymatic operation, ran for 16days at 45°C. Highest naringenin biosynthesis was attained at a flow rate of 10mLh(-1). Highest volumetric (78molL(-1)h(-1)) and specific (26molh(-1)genzyme(-1)) productivities were attained at 30mLh(-1). The activity of NGase in electrospun nanofibers remained constant for almost 16days of operation at 10mLh(-1). Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. The control of beads diameter of bead-on-string electrospun nanofibers and the corresponding release behaviors of embedded drugs.

    Science.gov (United States)

    Li, Tingxiao; Ding, Xin; Tian, Lingling; Hu, Jiyong; Yang, Xudong; Ramakrishna, Seeram

    2017-05-01

    Bead-on-string nanofibers, with appropriate control of the beads diameter, are potential fibrous structures for efficient encapsulation of particle drugs in micron scales and could achieve controlled drug release for tissue engineering applications. In this study, the beads diameter of electrospun bead-on-string nanofibers was controlled by adjusting the concentration of spinning polymer, poly (lactic-co-glycolic acid) (PLGA), and the solvent ratio of chloroform to acetone. The images of the scanning electron microscopy (SEM) suggested that bead-on-string nanofibers could be successfully obtained only with a certain range of PLGA solution concentration. Moreover, with the decrease in the solvent ratio of chloroform to acetone, the range was left-shifted towards a smaller concentration. In addition, increase in the PLGA solution concentration within the range the beads diameter became greater and the shape of the beads changed from oval to slender when increasing the PLGA concentration within the range. The bead-on-string nanofibers with different beads diameter were further used to load micro-particle drugs of tetracycline hydrochloride, as a model drug, to examine the release behavior of nanofibers scaffold. The release profiles of drug loaded bead-on-string nanofibers demonstrated the possibility to alleviate the burst drug release by means of beads diameter control. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. A novel shortened electrospun nanofiber modified with a 'concentrated' polymer brush

    Directory of Open Access Journals (Sweden)

    Chiaki Yoshikawa, Kun Zhang, Ewelina Zawadzak and Hisatoshi Kobayashi

    2011-01-01

    Full Text Available We report the fabrication of shortened electrospun polymer fibers with a well-defined concentrated polymer brush. We first prepared electrospun nanofibers from a random copolymer of styrene and 4-vinylbenzyl 2-bromopropionate, with number-average molecular weight Mn=105 200 and weight-average molecular weight Mw=296 700 (Mw/Mn=2.82. The fibers had a diameter of 593±74 nm and contained initiating sites for surface-initiated atom transfer radical polymerization (SI-ATRP. Then, SI-ATRP of hydrophilic styrene sodium sulfonate (SSNa was carried out in the presence of a free initiator and the hydrophobic fibers. Gel permeation chromatography confirmed that Mn and Mw/Mn values were almost the same for free polymers and graft polymers. Mn agreed well with the theoretical prediction, and Mw/Mn was relatively low (<1.3 in all the examined cases, indicating that this polymerization proceeded in a living manner. Using the values of the graft amount measured by Fourier transform infrared spectroscopy, the surface area, and Mn, we calculated the graft density σ as 0.22 chains nm−2. This value was nearly equal to the density obtained on silicon wafers (σ=0.24 chains nm−2, which is categorized into the concentrated brush regime. Finally, we mechanically cut the fibers with a concentrated poly(SSNa brush by a homogenizer. With increasing cutting time, the fiber length became shorter and more homogenous (11±17 μm after 3 h. The shortened fibers exhibited excellent water dispersibility owing to the hydrophilic poly(SSNa brush layer.

  5. Effect of Processing Parameters on the Morphology of PVDF Electrospun Nanofiber

    Science.gov (United States)

    Zulfikar, M. A.; Afrianingsih, I.; Nasir, M.; Alni, A.

    2018-03-01

    Electrospinning is a process that produces continuous polymer fibers with diameters in the submicron range through the action of an external electric field imposed on a polymer solution or melt. Because of the tiny diameter in several hundreds of nanometers and the high porosity, electrospun membranes show potential applications in extensive areas such as filtration systems, biomedical tissue templates, drug delivery membranes, and so on. In the electrospinning process, some parameters such as polymer concentration, feeding rate of the polymer solution, additives, humidity, viscosity, surface tension, applied voltage, and nozzle-to ground collector distance will affect the fiber diameter and morphology. In this work, we have evaluated the effects of two processing parameters including the flow rate of the polymer solution and nozzle-to ground collector distance, on the morphology of the fibers formed. The solutions used in the electrospinning experiments were prepared using Poly(vinylidene fluoride) (PVDF). This material was dissolved in N,N-dimethylformamide (DMF) to make solutions with concentrations of 20 wt%. These solutions was electrospun using a 5 mL plastic syringe with an 8 gauge stainless needle at an applied voltage of 20.0 kV, a flow rate of 0.02-0.04 mL/min and nozzle-to ground collector distance of 12 and 15 cm. Electrospinning of PVDF polymer solution was performed in horizontal alignment having a grounded aluminum foil which serves as a collector. The nanofibers obtained were characterized by polarizing optical microscope. We find that the low flow rate of the polymer solution and nozzle-to ground collector distance are strongly correlated with the formation of bead defects in the fibers.

  6. Electrospun PLLA nanofiber scaffolds and their use in combination with BMP-2 for reconstruction of bone defects.

    Science.gov (United States)

    Schofer, Markus D; Roessler, Philip P; Schaefer, Jan; Theisen, Christina; Schlimme, Sonja; Heverhagen, Johannes T; Voelker, Maximilian; Dersch, Roland; Agarwal, Seema; Fuchs-Winkelmann, Susanne; Paletta, Jürgen R J

    2011-01-01

    Adequate migration and differentiation of mesenchymal stem cells is essential for regeneration of large bone defects. To achieve this, modern graft materials are becoming increasingly important. Among them, electrospun nanofiber scaffolds are a promising approach, because of their high physical porosity and potential to mimic the extracellular matrix (ECM). The objective of the present study was to examine the impact of electrospun PLLA nanofiber scaffolds on bone formation in vivo, using a critical size rat calvarial defect model. In addition we analyzed whether direct incorporation of bone morphogenetic protein 2 (BMP-2) into nanofibers could enhance the osteoinductivity of the scaffolds. Two critical size calvarial defects (5 mm) were created in the parietal bones of adult male Sprague-Dawley rats. Defects were either (1) left unfilled, or treated with (2) bovine spongiosa, (3) PLLA scaffolds alone or (4) PLLA/BMP-2 scaffolds. Cranial CT-scans were taken at fixed intervals in vivo. Specimens obtained after euthanasia were processed for histology, histomorphometry and immunostaining (Osteocalcin, BMP-2 and Smad5). PLLA scaffolds were well colonized with cells after implantation, but only showed marginal ossification. PLLA/BMP-2 scaffolds showed much better bone regeneration and several ossification foci were observed throughout the defect. PLLA/BMP-2 scaffolds also stimulated significantly faster bone regeneration during the first eight weeks compared to bovine spongiosa. However, no significant differences between these two scaffolds could be observed after twelve weeks. Expression of osteogenic marker proteins in PLLA/BMP-2 scaffolds continuously increased throughout the observation period. After twelve weeks osteocalcin, BMP-2 and Smad5 were all significantly higher in the PLLA/BMP-2 group than in all other groups. Electrospun PLLA nanofibers facilitate colonization of bone defects, while their use in combination with BMP-2 also increases bone regeneration in

  7. Electrospun PLLA nanofiber scaffolds and their use in combination with BMP-2 for reconstruction of bone defects.

    Directory of Open Access Journals (Sweden)

    Markus D Schofer

    Full Text Available Adequate migration and differentiation of mesenchymal stem cells is essential for regeneration of large bone defects. To achieve this, modern graft materials are becoming increasingly important. Among them, electrospun nanofiber scaffolds are a promising approach, because of their high physical porosity and potential to mimic the extracellular matrix (ECM.The objective of the present study was to examine the impact of electrospun PLLA nanofiber scaffolds on bone formation in vivo, using a critical size rat calvarial defect model. In addition we analyzed whether direct incorporation of bone morphogenetic protein 2 (BMP-2 into nanofibers could enhance the osteoinductivity of the scaffolds. Two critical size calvarial defects (5 mm were created in the parietal bones of adult male Sprague-Dawley rats. Defects were either (1 left unfilled, or treated with (2 bovine spongiosa, (3 PLLA scaffolds alone or (4 PLLA/BMP-2 scaffolds. Cranial CT-scans were taken at fixed intervals in vivo. Specimens obtained after euthanasia were processed for histology, histomorphometry and immunostaining (Osteocalcin, BMP-2 and Smad5.PLLA scaffolds were well colonized with cells after implantation, but only showed marginal ossification. PLLA/BMP-2 scaffolds showed much better bone regeneration and several ossification foci were observed throughout the defect. PLLA/BMP-2 scaffolds also stimulated significantly faster bone regeneration during the first eight weeks compared to bovine spongiosa. However, no significant differences between these two scaffolds could be observed after twelve weeks. Expression of osteogenic marker proteins in PLLA/BMP-2 scaffolds continuously increased throughout the observation period. After twelve weeks osteocalcin, BMP-2 and Smad5 were all significantly higher in the PLLA/BMP-2 group than in all other groups.Electrospun PLLA nanofibers facilitate colonization of bone defects, while their use in combination with BMP-2 also increases bone

  8. Functionalized chitosan electrospun nanofiber for effective removal of trace arsenate from water

    Science.gov (United States)

    Min, Ling-Li; Zhong, Lu-Bin; Zheng, Yu-Ming; Liu, Qing; Yuan, Zhi-Huan; Yang, Li-Ming

    2016-08-01

    An environment-friendly iron functionalized chitosan elctrospun nanofiber (ICS-ENF) was synthesized for trace arsenate removal from water. The ICS-ENF was fabricated by electrospinning a mixture of chitosan, PEO and Fe3+ followed by crosslinking with ammonia vapor. The physicochemical properties of ICS-ENF were characterized by FESEM, TEM-EDX and XRD. The ICS-ENF was found to be highly effective for As(V) adsorption at neutral pH. The As(V) adsorption occurred rapidly and achieved equilibrium within 100 min, which was well fitted by pseudo-second-order kinetics model. The As(V) adsorption decreased with increased ionic strength, suggesting an outer-sphere complexation of As(V) on ICS-ENF. Freundlich model well described the adsorption isotherm, and the maximum adsorption capacity was up to 11.2 mg/g at pH 7.2. Coexisting anions of chloride and sulfate showed negligible influence on As(V) removal, but phosphate and silicate significantly reduced As(V) adsorption by competing for adsorption sites. FTIR and XPS analysis demonstrated -NH, -OH and C-O were responsible for As(V) uptake. ICS-ENF was easily regenerated using 0.003 M NaOH, and the removal rate remained above 98% after ten successively adsorption-desorption recycles. This study extends the potential applicability of electrospun nanofibers for water purification and provides a promising approach for As(V) removal from water.

  9. One-step synthesis of size-tunable Ag nanoparticles incorporated in electrospun PVA/cyclodextrin nanofibers.

    Science.gov (United States)

    Celebioglu, Asli; Aytac, Zeynep; Umu, Ozgun C O; Dana, Aykutlu; Tekinay, Turgay; Uyar, Tamer

    2014-01-01

    One-step synthesis of size-tunable silver nanoparticles (Ag-NP) incorporated into electrospun nanofibers was achieved. Initially, in situ reduction of silver salt (AgNO3) to Ag-NP was carried out in aqueous solution of polyvinyl alcohol (PVA). Here, PVA was used as reducing agent and stabilizing polymer as well as electrospinning polymeric matrix for the fabrication of PVA/Ag-NP nanofibers. Afterwards, hydroxypropyl-beta-cyclodextrin (HPβCD) was used as an additional reducing and stabilizing agent in order to control size and uniform dispersion of Ag-NP. The size of Ag-NP was ∼8 nm and some Ag-NP aggregates were observed for PVA/Ag-NP nanofibers, conversely, the size of Ag-NP decreased from ∼8 nm down to ∼2 nm within the fiber matrix without aggregation were attained for PVA/HPβCD nanofibers. The PVA/Ag-NP and PVA/HPβCD/Ag-NP nanofibers exhibited surface enhanced Raman scattering (SERS) effect. Moreover, antibacterial properties of PVA/Ag-NP and PVA/HPβCD/Ag-NP nanofibrous mats were tested against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Coaxial PCL/PVA electrospun nanofibers: osseointegration enhancer and controlled drug release device

    International Nuclear Information System (INIS)

    Song, Wei; Shi, Tong; Ren, Weiping; Yu, Xiaowei; Markel, David C

    2013-01-01

    The failure of prosthesis after total joint replacement is mainly due to dysfunctional osseointegration and implant infection. There is a critical need for orthopedic implants that promote rapid osseointegration and prevent bacterial colonization, particularly when placed in bone compromised by disease or physiology of the patients. The aim of this study was to fabricate a novel coaxial electrospun polycaprolactone (PCL)/polyvinyl alcohol (PVA) core-sheath nanofiber (NF) blended with both hydroxyapatite nanorods (HA) and type I collagen (Col) (PCL Col /PVA HA ). Doxycycline (Doxy) and dexamethasone (Dex) were successfully incorporated into the PCL Col /PVA HA NFs for controlled release. The morphology, surface hydrophilicity and mechanical properties of the PCL/PVA NF mats were analyzed by scanning electron microscopy, water contact angle and atomic force microscopy. The PCL Col /PVA HA NFs are biocompatible and enhance the adhesion and proliferation of murine pre-osteoblastic MC3T3 cells. The release of Doxy and Dex from coaxial PCL Col /PVA HA NFs showed more controlled release compared with the blended NFs. Using an ex vivo porcine bone implantation model we found that the PCL Col /PVA HA NFs bind firmly on the titanium rod surface and the NFs coating remained intact on the surface of titanium rods after pullout. No disruption or delamination was observed after the pullout test. These findings indicate that PCL Col /PVA HA NFs encapsulating drugs have great potential in enhancing implant osseointegration and preventing implant infection. (paper)

  11. Coaxial PCL/PVA electrospun nanofibers: osseointegration enhancer and controlled drug release device.

    Science.gov (United States)

    Song, Wei; Yu, Xiaowei; Markel, David C; Shi, Tong; Ren, Weiping

    2013-09-01

    The failure of prosthesis after total joint replacement is mainly due to dysfunctional osseointegration and implant infection. There is a critical need for orthopedic implants that promote rapid osseointegration and prevent bacterial colonization, particularly when placed in bone compromised by disease or physiology of the patients. The aim of this study was to fabricate a novel coaxial electrospun polycaprolactone (PCL)/polyvinyl alcohol (PVA) core-sheath nanofiber (NF) blended with both hydroxyapatite nanorods (HA) and type I collagen (Col) (PCL(Col)/PVA(HA)). Doxycycline (Doxy) and dexamethasone (Dex) were successfully incorporated into the PCL(Col)/PVA(HA) NFs for controlled release. The morphology, surface hydrophilicity and mechanical properties of the PCL/PVA NF mats were analyzed by scanning electron microscopy, water contact angle and atomic force microscopy. The PCL(Col)/PVA(HA) NFs are biocompatible and enhance the adhesion and proliferation of murine pre-osteoblastic MC3T3 cells. The release of Doxy and Dex from coaxial PCL(Col)/PVA(HA) NFs showed more controlled release compared with the blended NFs. Using an ex vivo porcine bone implantation model we found that the PCL(Col)/PVA(HA) NFs bind firmly on the titanium rod surface and the NFs coating remained intact on the surface of titanium rods after pullout. No disruption or delamination was observed after the pullout test. These findings indicate that PCL(Col)/PVA(HA) NFs encapsulating drugs have great potential in enhancing implant osseointegration and preventing implant infection.

  12. Mechanism of Action of Electrospun Chitosan-Based Nanofibers against Meat Spoilage and Pathogenic Bacteria.

    Science.gov (United States)

    Arkoun, Mounia; Daigle, France; Heuzey, Marie-Claude; Ajji, Abdellah

    2017-04-06

    This study investigates the antibacterial mechanism of action of electrospun chitosan-based nanofibers (CNFs), against Escherichia coli , Salmonella enterica serovar Typhimurium, Staphylococcus aureus and Listeria innocua , bacteria frequently involved in food contamination and spoilage. CNFs were prepared by electrospinning of chitosan and poly(ethylene oxide) (PEO) blends. The in vitro antibacterial activity of CNFs was evaluated and the susceptibility/resistance of the selected bacteria toward CNFs was examined. Strain susceptibility was evaluated in terms of bacterial type, cell surface hydrophobicity, and charge density, as well as pathogenicity. The efficiency of CNFs on the preservation and shelf life extension of fresh red meat was also assessed. Our results demonstrate that the antibacterial action of CNFs depends on the protonation of their amino groups, regardless of bacterial type and their mechanism of action was bactericidal rather than bacteriostatic. Results also indicate that bacterial susceptibility was not Gram-dependent but strain-dependent, with non-virulent bacteria showing higher susceptibility at a reduction rate of 99.9%. The susceptibility order was: E. coli > L. innocua > S. aureus > S. Typhimurium. Finally, an extension of one week of the shelf life of fresh meat was successfully achieved. These results are promising and of great utility for the potential use of CNFs as bioactive food packaging materials in the food industry, and more specifically in meat quality preservation.

  13. Electrospun water-soluble polymer nanofibers for the dehydration and storage of sensitive reagents

    International Nuclear Information System (INIS)

    Dai, Minhui; Nugen, Sam R; Senecal, Andre

    2014-01-01

    The ability to preserve and deliver reagents remains an obstacle for the successful deployment of self-contained diagnostic microdevices. In this study we investigated the ability of bacteriophage T7 to be encapsulated and preserved in water soluble nanofibers. The bacteriophage T7 was added to mixtures of polyvinylpyrrolidone and water and electrospun onto a grounded plate. Trehalose and magnesium salts were added to the mixtures to determine their effect on the infectivity of the bacteriophage following electrospinning and during storage. The loss of T7 infectivity was determined immediately following electrospinning and during storage using agar overlay plating and plaque counting. The results indicate that the addition of magnesium salts protects the bacteriophage during the relatively violent and high voltage electrospinning process, but is not as effective as a protectant during storage of the dried T7. Conversely, the addition of trehalose into the electrospinning mix has little effect on the electrospinning, but a more significant role as a protectant during storage. (papers)

  14. Electrospun conducting polymer nanofibers as the active material in sensors and diodes

    Science.gov (United States)

    Pinto, Nicholas J.

    2013-03-01

    Polyaniline doped with camphorsulfonic acid (PANi-HCSA) and poly(3,4-ethylenedioxythiophene) doped with polystyrene sulfonic acid (PEDOT-PSSA) were electrospun separately to obtain individual nanofibers which were captured on Si/SiO2 substrates and electrically characterized. The fiber resistance was recorded as a function of time in the presence of vapours of aliphatic alcohols of varying sizes. Due to the large surface to volume ratio, uniform diameter and small quantity of active material used in the construction, these sensor responses are very quick. Sensors made from individual fibers also show true saturation upon exposure to and removal of the sensing gas. A Schottky diode was also fabricated using an n-doped Si/SiO2 substrate and a single PANi-HCSA fiber and tested in vacuum and in ammonia gas. The diode response was instantaneous upon exposure to ammonia with nearly complete recovery of the current upon pumping out the ammonia, thereby making it a reusable sensor with rectifying behaviour i.e. multifunctional.

  15. Enhanced piezoresponse of highly aligned electrospun poly(vinylidene fluoride) nanofibers

    Science.gov (United States)

    Kang, Sung Bum; Won, Sang Hyuk; Im, Min Ji; Kim, Chan Ul; Park, Won Il; Baik, Jeong Min; Choi, Kyoung Jin

    2017-09-01

    Well-ordered nanostructure arrays with controlled densities can potentially improve material properties; however, their fabrication typically involves the use of complicated processing techniques. In this work, we demonstrate a uniaxial alignment procedure for fabricating poly(vinylidene fluoride) (PVDF) electrospun nanofibers (NFs) by introducing collectors with additional steps. The mechanism of the observed NF alignment, which occurs due to the concentration of lateral electric field lines around collector steps, has been elucidated via finite-difference time-domain simulations. The membranes composed of well-aligned PVDF NFs are characterized by a higher content of the PVDF β-phase, as compared to those manufactured from randomly orientated fibers. The piezoelectric energy harvester, which was fabricated by transferring well-aligned PVDF NFs onto flexible substrates with Ag electrodes attached to both sides, exhibited a 2-fold increase in the output voltage and a 3-fold increase in the output current as compared to the corresponding values obtained for the device manufactured from randomly oriented NFs. The enhanced piezoresponse observed for the aligned PVDF NFs is due to their higher β-phase content, denser structure, smaller effective radius of curvature during bending, greater applied strain, and higher fraction of contributing NFs.

  16. Preparation, characterization, and in vitro diffusion study of nonwoven electrospun nanofiber of curcumin-loaded cellulose acetate phthalate polymer

    Directory of Open Access Journals (Sweden)

    Rramaswamy Ravikumar

    2017-09-01

    Full Text Available Novel curcumin (CUR-loaded cellulose acetate phthalate (CAP nonwoven electrospun nanofiber (NF transdermal mat was developed and evaluated for its in vitro CUR diffusion properties. Various CAP solutions from 5 to 20 wt% were tested; 17.5 wt% was found to be a suitable concentration for NF fabrication without defects, such as bubble or ribbon structures. The selected wt% CAP solution was loaded with CUR and electrospun into NFs. The prepared CUR-loaded NFs were characterized using scanning electron microscopy, X-ray diffraction, ultraviolet–visible spectroscopy, thermogravimetric analysis (TGA, and in vitro diffusion studies. The as-prepared fibers demonstrated controlled in vitro transdermal delivery of CUR for up to 24 h.

  17. Preparation, characterization, and in vitro diffusion study of nonwoven electrospun nanofiber of curcumin-loaded cellulose acetate phthalate polymer.

    Science.gov (United States)

    Ravikumar, Rramaswamy; Ganesh, Mani; Ubaidulla, Udumansha; Young Choi, Eun; Tae Jang, Hyun

    2017-09-01

    Novel curcumin (CUR)-loaded cellulose acetate phthalate (CAP) nonwoven electrospun nanofiber (NF) transdermal mat was developed and evaluated for its in vitro CUR diffusion properties. Various CAP solutions from 5 to 20 wt% were tested; 17.5 wt% was found to be a suitable concentration for NF fabrication without defects, such as bubble or ribbon structures. The selected wt% CAP solution was loaded with CUR and electrospun into NFs. The prepared CUR-loaded NFs were characterized using scanning electron microscopy, X-ray diffraction, ultraviolet-visible spectroscopy, thermogravimetric analysis (TGA), and in vitro diffusion studies. The as-prepared fibers demonstrated controlled in vitro transdermal delivery of CUR for up to 24 h.

  18. Highly efficient hybrid energy generator: coupled organic photovoltaic device and randomly oriented electrospun poly(vinylidene fluoride) nanofiber.

    Science.gov (United States)

    Park, Boongik; Lee, Kihwan; Park, Jongjin; Kim, Jongmin; Kim, Ohyun

    2013-03-01

    A hybrid architecture consisting of an inverted organic photovoltaic device and a randomly-oriented electrospun PVDF piezoelectric device was fabricated as a highly-efficient energy generator. It uses the inverted photovoltaic device with coupled electrospun PVDF nanofibers as tandem structure to convert solar and mechanical vibrations energy to electricity simultaneously or individually. The power conversion efficiency of the photovoltaic device was also significantly improved up to 4.72% by optimized processes such as intrinsic ZnO, MoO3 and active layer. A simple electrospinning method with the two electrode technique was adopted to achieve a high voltage of - 300 mV in PVDF piezoelectric fibers. Highly-efficient HEG using voltage adder circuit provides the conceptual possibility of realizing multi-functional energy generator whenever and wherever various energy sources are available.

  19. Influence of layer-by-layer assembled electrospun poly (L-lactic acid) nanofiber mats on the bioactivity of endothelial cells

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Keke; Zhang, Xiazhi; Yang, Wufeng; Liu, Xiaoyan; Jiao, Yanpeng, E-mail: tjiaoyp@jnu.edu.cn; Zhou, Changren

    2016-12-30

    Highlights: • Layer-by-layer assembled PLLA nanofiber mats were successfully prepared. • The modified PLLA nanofiber mats enhanced the adhesion, proliferation of endothelial cells. • The modified PLLA nanofiber mats had inhibited the inflammatory response to some extent. - Abstract: Electrospun poly(L-lactic acid) (PLLA) nanofiber mats were successfully modified by deposition of multilayers with chitosan (CS), heparin (Hep) and graphene oxide (GO) through electrostatic layer-by-layer (LBL) self-assembly method. In this study, the surface properties of PLLA nanofiber mats before and after modification were investigated via scanning electron microscope (SEM), atomic force microscopy (AFM), attenuated total reflectance fourier transformation infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and water contact angle measurement. In addition, the cytocompatibility of the modified PLLA nanofiber mats were investigated by testing endothelial cells compatibility, including cell attachment, cell proliferation and cell cycle. The results revealed that the surfaces of modified PLLA nanofiber mats become much rougher, stifiness and the hydrophilicity of the LBL modified PLLA nanofiber mats were improved compared to original PLLA one. Moreover, the modified PLLA nanofiber mats had promoted the endothelial cells viability attachment significantly. Besides, we studied the PLLA nanofiber mats on the expression of necrosis factor (TNF-α), interleukine-1β (IL-1β), monocyte chemoattractant protein-1 (MCP-1) and vascular cell adhesion molecule-1 (VCAM-1) in endothelial cells. The results showed that modified PLLA nanofiber mats had inhibited the inflammatory response to some extent.

  20. Electrospun black titania nanofibers: Influence of hydrogen plasma-induced disorder on the electronic structure and photoelectrochemical performance

    OpenAIRE

    Lepcha, A.; Maccato, C.; Mettenbörger, A.; Andreu, T.; Mayrhofer, L.; Walter, M.; Olthof, S.; Ruoko, T.P.; Klein, A.; Moseler, M.; Meerholz, K.; Morante, J.R.; Barreca, D.; Mathur, S.

    2015-01-01

    This work encompasses a facile method for tailoring surface defects in electrospun TiO2 nanofibers by employing hydrogen plasma treatments. This amiable processing method was proven with SQUID, EPR, and XPS to be highly effective in generating oxygen vacancies, accompanied by the reduction of Ti4+ centers to Ti3+, resulting in the formation of black titania. The treatment temperature was found to affect the Ti3+/Ti4+ ratios and surface valence, while preserving the original 1D morphology of t...

  1. Electrospun ZnFe{sub 2}O{sub 4}-based nanofiber composites with enhanced supercapacitive properties

    Energy Technology Data Exchange (ETDEWEB)

    Agyemang, Frank Ofori; Kim, Hern, E-mail: hernkim@mju.ac.kr

    2016-09-15

    Highlights: • Electrospun ZnFe{sub 2}O{sub 4}-based nanofibers were successfully fabricated. • The electrochemical properties of ZnFe{sub 2}O{sub 4} were enhanced by addition of ZnO and Fe{sub 2}O{sub 3.} • A specific capacitance of 590 F g{sup −1} was achieved from a CV curve at a scan rate of 5 mV s{sup −1.} • The electrode materials poses excellent cycling stability even after 3000 cycles. - Abstract: Herein, we are reporting a facile method to synthesis ZnFe{sub 2}O{sub 4}-based nanofibers (ZnFe{sub 2}O{sub 4}, ZnO–ZnFe{sub 2}O{sub 4} and Fe{sub 2}O{sub 3}–ZnFe{sub 2}O{sub 4}) via the electrospinning technique using zinc acetonate and ferric acetonate as the metal oxide precursor and polyvinyl pyrrolidone (PVP) as the polymer. The as-prepared electrospun nanofiber composites were calcined at 500 °C to obtain crystalline porous nanofibers. The effect of different compositions on the morphology of each sample as well as their electrochemical properties when employed as electrode materials was studied. The results show that the as-prepared electrodes exhibited excellent performance with their specific capacitances calculated from the CV curves as 590, 490 and 450 F g{sup −1} for Fe{sub 2}O{sub 3}–ZnFe{sub 2}O{sub 4}, ZnO–ZnFe{sub 2}O{sub 4} and ZnFe{sub 2}O{sub 4} respectively at a scan rate of 5 mV s{sup −1}. Excellent stability of the electrodes was also observed even after 3000 cycles. The results obtained suggest these electrode materials might be promising candidates for supercapacitor application.

  2. Enhanced Electrochemical Performance of Electrospun Ag/Hollow Glassy Carbon Nanofibers as Free-standing Li-ion Battery Anode

    International Nuclear Information System (INIS)

    Shilpa; Sharma, Ashutosh

    2015-01-01

    Silver with a high theoretical capacity for lithium storage is an attractive alloy based anode for Li-ion batteries, but large volume changes associated with AgLi x alloy formation leads to electrode cracking, pulverization and rapid capacity fading. A buffer matrix, like the electrospun hollow carbon nanofibers, can reduce this problem to a great extent. Herein, we demonstrate the facile synthesis of a free-standing, binder free Ag-C hybrid electrode through co-axial electrospinning, where well dispersed Ag nanoparticles are embedded in hollow carbon nanofibers. Using this approach, the long cycle life of carbon is complemented with the high lithium storage capacity of Ag, resulting in a high performance anode. The Ag-C composite electrode delivers a capacity of 739 mAh g −1 (>conventional graphite anodes) at 50 mA g −1 , with ∼85% capacity retention after 100 cycles. In addition, the Ag-C composite nanofibers are highly porous and exhibit a large accessible surface area (∼726.9 m 2 g −1 ) with an average pore diameter of ∼6.07 nm. The encapsulation of Ag in the hollow interiors not only provides additional lithium storage sites but also enhances the electronic conductivity, which combined with the reduced lithium diffusion path lengths in the nanofibers result in faster charge-discharge kinetics and hence a high rate performance

  3. Characterization and optimization of electrospun TiO2/PVP nanofibers using Taguchi design of experiment method

    Directory of Open Access Journals (Sweden)

    H. Albetran

    2015-09-01

    Full Text Available TiO2 nanofibers were prepared within polyvinylpyrrolidone (PVP polymer using a combination of sol–gel and electrospinning techniques. Based on a Taguchi design of experiment (DoE method, the effects of sol–gel and electrospinning on the TiO2/PVP nanofibers’ diameter, including titanium isopropoxide (TiP concentration, flow rate, needle tip-to-collector distance, and applied voltage were evaluated. The analysis of DoE experiments for nanofiber diameters demonstrated that TiP concentration was the most significant factor. An optimum combination to obtain smallest diameters was also determined with a minimum variation for electrospun TiO2/PVP nanofibers. The optimum combination was determined to be a 60% TiP concentration, at a flow rate of 1 ml/h, with the needle tip-to-collector distance at 11 cm (position a, and the applied voltage of 18 kV. This combination was further validated by conducting a confirmation experiment that used two different needles to study the effect of needle size. The average nanofiber diameter was approximately the same for both needle sizes in good accordance with the optimum condition estimated by the Taguchi DoE method.

  4. Electrospun PVA/HAp nanocomposite nanofibers: biomimetics of mineralized hard tissues at a lower level of complexity

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Gyeong-Man; Asran, Ashraf Sh; Michler, Georg H [Institute of Physics, Martin-Luther-University Halle-Wittenberg, D-06099 Halle/S (Germany); Simon, Paul [Max-Planck Institute for Chemical Physics of Solids, Noethnitzer Strasse 40, D-01187 Dresden (Germany); Kim, Jeong-Sook [Department of Dental Technology, Daegu Health College, 702-722 Daegu (Korea, Republic of)], E-mail: gyeong.kim@physik.uni-halle.de

    2008-12-01

    Based on the biomimetic approaches the present work describes a straightforward technique to mimic not only the architecture (the morphology) but also the chemistry (the composition) of the lowest level of the hierarchical organization of bone. This technique uses an electrospinning (ES) process with polyvinyl alcohol (PVA) and hydroxyapatite (HAp) nanoparticles. To determine morphology, crystalline structures and thermal properties of the resulting electrospun fibers with the pure PVA and PVA/HAp nanocomposite (NC) before electrospinning various techniques were employed, including transmission electron microscopy (TEM), high-resolution TEM (HR-TEM), scanning electron microscopy (SEM), x-ray diffraction (XRD), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In addition, FT-IR spectroscopy was carried out to analyze the complex structural changes upon undergoing electrospinning as well as interactions between HAp and PVA. The morphological and crystallographic investigations revealed that the rod-like HAp nanoparticles exhibit a nanoporous morphology and are embedded within the electrospun fibers. A large number of HAp nanorods are preferentially oriented parallel to the longitudinal direction of the electrospun PVA fibers, which closely resemble the naturally mineralized hard tissues of bones. Due to abundant OH groups present in PVA and HAp nanorods, they strongly interact via hydrogen bonding within the electrospun PVA/HAp NC fibers, which results in improved thermal properties. The unique physiochemical features of the electrospun PVA/HAp NC nanofibers prepared by the ES process will open up a wide variety of future applications related to hard tissue replacement and regeneration (bone and dentin), not limited to coating implants.

  5. Robust Trypsin Coating on Electrospun Polymer Nanofibers in Rigorous Conditions and Its Uses for Protein Digestion

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Hye-Kyung; Kim, Byoung Chan; Jun, Seung-Hyun; Chang, Mun Seock; Lopez-Ferrer, Daniel; Smith, Richard D.; Gu, Man Bock; Lee, Sang-Won; Kim, Beom S.; Kim, Jungbae

    2010-12-15

    An efficient protein digestion in proteomic analysis requires the stabilization of proteases such as trypsin. In the present work, trypsin was stabilized in the form of enzyme coating on electrospun polymer nanofibers (EC-TR), which crosslinks additional trypsin molecules onto covalently-attached trypsin (CA-TR). EC-TR showed better stability than CA-TR in rigorous conditions, such as at high temperatures of 40 °C and 50 °C, in the presence of organic co-solvents, and at various pH's. For example, the half-lives of CA-TR and EC-TR were 0.24 and 163.20 hours at 40 ºC, respectively. The improved stability of EC-TR can be explained by covalent-linkages on the surface of trypsin molecules, which effectively inhibits the denaturation, autolysis, and leaching of trypsin. The protein digestion was performed at 40 °C by using both CA-TR and EC-TR in digesting a model protein, enolase. EC-TR showed better performance and stability than CA-TR by maintaining good performance of enolase digestion under recycled uses for a period of one week. In the same condition, CA-TR showed poor performance from the beginning, and could not be used for digestion at all after a few usages. The enzyme coating approach is anticipated to be successfully employed not only for protein digestion in proteomic analysis, but also for various other fields where the poor enzyme stability presently hampers the practical applications of enzymes.

  6. In vitro and in vivo evaluation of electrospun nanofibers of PCL, chitosan and gelatin: A comparative study

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, S.R., E-mail: srrg@campus.fct.unl.pt [Centro de Física e Investigação Tecnológica/Departamento de Física Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Rodrigues, G. [Centro de Biologia Ambiental/Departamento de Biologia Animal Faculdade de Ciências da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Martins, G.G. [Centro de Biologia Ambiental/Departamento de Biologia Animal Faculdade de Ciências da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Instituto Gulbenkian de Ciência, R. da Quinta Grande, 6, 2780-156 Oeiras (Portugal); Roberto, M.A. [Departamento de Cirurgia Plástica e Reconstrutiva e Unidade de Queimados, Hospital de São José, Rua José António Serrano, 1150-199 Lisboa (Portugal); Mafra, M. [Serviço de Anatomia Patológica, Hospital de São José, Rua José António Serrano, 1150-199 Lisboa (Portugal); Henriques, C.M.R. [Centro de Física e Investigação Tecnológica/Departamento de Física Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); and others

    2015-01-01

    Many polymers have been investigated with respect to their use in skin tissue engineering. However, directly comparable data on the role played by different polymers in assisting skin wound healing requires their in vitro and in vivo evaluation under the same conditions. Therefore, we performed a study in order to compare the performance of electrospun nanofiber mats from three different polymers concerning cell–scaffold interaction and wound healing promotion. A polyester (polycaprolactone, PCL), a protein (gelatin from cold water fish skin, GEL) and a polysaccharide (chitosan, CS) were the polymers chosen. Gelatin nanofibers were crosslinked with glutaraldehyde vapor. The scaffolds were characterized physico-chemically, in vitro by seeding with human fetal fibroblasts, HFFF2, and used in vivo as skin substitutes in a rat wound model with total skin removal. In vitro tests revealed that cells adhered and proliferated in all scaffolds. However, cells deep into the scaffold were only observed in the PCL and CS scaffolds. In in vivo tests CS scaffolds had the highest impact on the healing process by decreasing the extent of wound contraction and enhancing the production of a neodermis and re-epithelialization of the wound. - Highlights: • We produced and compared the properties of electrospun PCL, CS and fish GEL. • In vitro, cells adhered and proliferated better on GEL scaffolds. • Deep cell migration was observed in the PCL and CS matrices. • In vivo, both CS and GEL matrices integrated well within the wounds. • Only CS effectively blocked, although only partially, the contraction phenomenon.

  7. Carbon nanotubes functionalized electrospun nanofibers formed 3D electrode enables highly strong ECL of peroxydisulfate and its application in immunoassay.

    Science.gov (United States)

    Dai, Hong; Xu, Guifang; Zhang, Shupei; Gong, Lingshan; Li, Xiuhua; Yang, Caiping; Lin, Yanyu; Chen, Jinghua; Chen, Guonan

    2014-11-15

    A new biosensing platform based on electrospun carbon nanotubes nanofibers (CNTs@PNFs) composite, which enabled strong electrochemiluminescent emission of peroxydisulfate, was firstly developed for immunoassay with favorable analytical performances, and then was utilized to evaluate the interaction between antibody and antigen in vitro. Moreover, the obvious ECL image of peroxydisulfate on the prepared sensing platform was firstly recorded in this report. In order to expand the application of peroxydisulfate ECL, the specific recognization biomolecules, α-fetoprotein (AFP) antibody was bound to the functionalized film via electrostatic interaction for fabricating label-free ECL immunosensor to detect α-AFP. Based on the ECL change resulting from the specific immunoreaction between antigen and antibody, the quantitative analysis for AFP with wide dynamic response in the range from 0.1 pg mL(-1) to 160 ng mL(-1) was realized. And the limit of detection was estimated to be 0.09 pg mL(-1). Therefore, the flexible sensing platform not only acted as the sensitized sensing element, but also offered a suitable carrier for immobilization of biological recognition elements with low-toxicity and eco-friendliness, which opened a promising approach to developing further electrospun nanofiber based amplified ECL biosensor with favorable analytical performances. Copyright © 2014 Elsevier B.V. All rights reserved.

  8. Electrospun manganese (III) oxide nanofiber based electrochemical DNA-nanobiosensor for zeptomolar detection of dengue consensus primer.

    Science.gov (United States)

    Tripathy, Suryasnata; Krishna Vanjari, Siva Rama; Singh, Vikrant; Swaminathan, S; Singh, Shiv Govind

    2017-04-15

    Nanoscale biosensors, owing to their high-sensitivity and extremely low limits-of-detection, have enabled the realization of highly complex and sophisticated miniaturized platforms for several important healthcare applications, the most predominant one being disease diagnosis. In particular, nanomaterial facilitated electrochemical detection of DNA hybridization has had an exceptional impact on fields such as genetics and cancerous mutation detection Here we report an ultrasensitive electrochemical platform using electrospun semi-conducting Manganese (III) Oxide (Mn 2 O 3 ) nanofibers for DNA Hybridization detection. The proposed platform coalesces the inherent advantages of metal-oxide nanofibers and electrochemical transduction techniques, resulting in label-free zeptomolar detection of DNA hybridization. As proof of concept, we demonstrate zeptomolar detection of Dengue consensus primer (limit of detection: 120×10 -21 M) both in control as well as spiked serum samples. Our reported detection limit is superior in comparison with previously reported electrochemical DNA hybridization sensors for Dengue virus detection, spanning both labeled and label-free transductions. This ultra-sensitivity, we believe, is a result of synthesizing a low bandgap electrospun metal-oxide nanomaterial corresponding to a specific oxidation state of Manganese. This methodology can be extended for detection of any hybridization of interest by simply adapting an appropriate functionalization protocol and thus is very generic in nature. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Integration of adsorption and reduction for uranium uptake based on SrTiO3/TiO2 electrospun nanofibers

    Science.gov (United States)

    Hu, Lin; Yan, Xue-Wu; Zhang, Xue-Ji; Shan, Dan

    2018-01-01

    The integration of adsorption and reduction for uranium uptake via photoelectrochemical method was conducted based on hetero-structure SrTiO3/TiO2 electrospun nanofibers. The SrTiO3/TiO2 was fabricated by two steps. First, TiO2 nanofibers were prepared via electrospinning, and then the SrTiO3 cubes grew on the surface of TiO2 nanofibers to form heterostructure by in situ hydrothermal treatment. For the uranium uptake based on photoelectrochemical method, the FTO electrodes modified by SrTiO3/TiO2 electrospun nanofibers removed uranium concentration by 81 ppm, higher than TiO2 nanoparticles, SrTiO3 nanoparticles and TiO2 electrospun nanofibers (59 ppm, 40 ppm and 70 ppm respectively). Besides, the photocurrent of these materials was also measured through photoelectrochemical measurements. Meanwhile, surface analyses using various techniques (Scanning electron microscopic, Transmission electron microscope and X-ray photoelectron spectroscopy) was also performed. Finally, the mechanism of electron transfer between SrTiO3/TiO2 and uranium was proposed.

  10. Assessment of material blending distribution for electrospun nanofiber membrane by Fourier transform infrared (FT-IR) microspectroscopy and image cluster analysis

    Science.gov (United States)

    Sunthornvarabhas, Jackapon; Thumanu, Kanjana; Limpirat, Wanwisa; Kim, Hyun-Joong; Piyachomkwan, Kuakoon; Sriroth, Klanarong

    2014-09-01

    Electrospun nanofibers between starch and polyethylene oxide were successfully prepared to be used as a template for wound healing application. Material blending ratios and fabrication conditions were optimized to determine the ability to control material spatial for further development. A fourier Transform Infrared (FT-IR) mapping system and purposed modified image clustering analysis were adopted to evaluate the material homogeneity of a sheet of homogeneous composite nanofibers. The fabrication conditions and material blending ratios both have an influence on the material distribution and optimum points were observed from this technique. This study showed the possibility of using a quick and non-destructive technique and a modified image cluster analysis technique to evaluate the homogeneity of the electrospun nanofiber sheet.

  11. Engineering Multi-scale Electrospun Structure for Integration into Architected 3-D Nanofibers for Cimex Annihilation: Fabrication and Mechanism Study

    Science.gov (United States)

    He, Shan; Zhang, Linxi; Liu, Ying; Rafailovich, Miriam; Garcia CenterPolymers at Engineered Interfaces Team

    In this study, engineered electrospun scaffolds with fibers oriented with designed curvature in three dimensions (3D) including the looped structure were developed based on the principle of electrostatic repulsion. Here we illustrate that 3D electrospun recycled polystyrene fibers could closely mimic the unique architectures of multi-direction and multi-layer nano-spiderweb. In contrast to virgin PS, the recycled PS (Dart Styrofoam) are known to contain zinc stearate which acts as a surfactant resulting in higher electrical charge and larger fiber curvature, hence, lower modulus. The surfactant, which is known to decrease the surface tension, may have also been effective at decreasing the confinement of the PS, where chain stretching was shown to occur, in response to the high surface tension at the air interface. Three dimensional flexible architecture with complex structures are shown to be necessary in order to block the motion of Cimex lectularius. Here we show how an engineered electrospun network of surfactant modified polymer fibers with calculated dimensions can be used to immobilize the insects. The mechanical response of the fibers has to be specifically tailored so that it is elastically deformed, without fracturing or flowing. Carefully controlling and tailoring the electrospinning parameters we can now utilize architected 3D nanofiber to create an environmental-friendly Cimex immobilization device which can lead to annihilation solution for all the other harmful insects.

  12. Computational predictions of the tensile properties of electrospun fibre meshes: effect of fibre diameter and fibre orientation.

    Science.gov (United States)

    Stylianopoulos, Triantafyllos; Bashur, Chris A; Goldstein, Aaron S; Guelcher, Scott A; Barocas, Victor H

    2008-10-01

    The mechanical properties of biomaterial scaffolds are crucial for their efficacy in tissue engineering and regenerative medicine. At the microscopic scale, the scaffold must be sufficiently rigid to support cell adhesion, spreading, and normal extracellular matrix deposition. Concurrently, at the macroscopic scale the scaffold must have mechanical properties that closely match those of the target tissue. The achievement of both goals may be possible by careful control of the scaffold architecture. Recently, electrospinning has emerged as an attractive means to form fused fibre scaffolds for tissue engineering. The diameter and relative orientation of fibres affect cell behaviour, but their impact on the tensile properties of the scaffolds has not been rigorously characterized. To examine the structure-property relationship, electrospun meshes were made from a polyurethane elastomer with different fibre diameters and orientations and mechanically tested to determine the dependence of the elastic modulus on the mesh architecture. Concurrently, a multiscale modelling strategy developed for type I collagen networks was employed to predict the mechanical behaviour of the polyurethane meshes. Experimentally, the measured elastic modulus of the meshes varied from 0.56 to 3.0 MPa depending on fibre diameter and the degree of fibre alignment. Model predictions for tensile loading parallel to fibre orientation agreed well with experimental measurements for a wide range of conditions when a fitted fibre modulus of 18 MPa was used. Although the model predictions were less accurate in transverse loading of anisotropic samples, these results indicate that computational modelling can assist in design of electrospun artificial tissue scaffolds.

  13. The influence of specimen thickness and alignment on the material and failure properties of electrospun polycaprolactone nanofiber mats.

    Science.gov (United States)

    Mubyana, Kuwabo; Koppes, Ryan A; Lee, Kristen L; Cooper, James A; Corr, David T

    2016-11-01

    Electrospinning is a versatile fabrication technique that has been recently expanded to create nanofibrous structures that mimic ECM topography. Like many materials, electrospun constructs are typically characterized on a smaller scale, and scaled up for various applications. This established practice is based on the assumption that material properties, such as toughness, failure stress and strain, are intrinsic to the material, and thus will not be influenced by specimen geometry. However, we hypothesized that the material and failure properties of electrospun nanofiber mats vary with specimen thickness. To test this, we mechanically characterized polycaprolactone (PCL) nanofiber mats of three different thicknesses in response to constant rate elongation to failure. To identify if any observed thickness-dependence could be attributed to fiber alignment, such as the effects of fiber reorientation during elongation, these tests were performed in mats with either random or aligned nanofiber orientation. Contrary to our hypothesis, the failure strain was conserved across the different thicknesses, indicating similar maximal elongation for specimens of different thickness. However, in both the aligned and randomly oriented groups, the ultimate tensile stress, short-range modulus, yield modulus, and toughness all decreased with increasing mat thickness, thereby indicating that these are not intrinsic material properties. These findings have important implications in engineered scaffolds for fibrous and soft tissue applications (e.g., tendon, ligament, muscle, and skin), where such oversights could result in unwanted laxity or reduced resistance to failure. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2794-2800, 2016. © 2016 Wiley Periodicals, Inc.

  14. Enhanced Piezoelectricity in a Robust and Harmonious Multilayer Assembly of Electrospun Nanofiber Mats and Microbead-Based Electrodes.

    Science.gov (United States)

    Kim, Young Won; Lee, Han Bit; Yeon, Si Mo; Park, Jeanho; Lee, Hye Jin; Yoon, Jonghun; Park, Suk Hee

    2018-02-14

    Here, we present a simple yet highly efficient method to enhance the output performance of a piezoelectric device containing electrospun nanofiber mats. Multiple nanofiber mats were assembled together to harness larger piezoelectric sources in the as-spun fibers, thereby providing enhanced voltage and current outputs compared to those of a single-mat device. In addition to the multilayer assembly, microbead-based electrodes were integrated with the nanofiber mats to deliver a complexed compression and tension force excitation to the piezoelectric layers. A vacuum-packing process was performed to attain a tight and well-organized assembly of the device components even though the total thickness was several millimeters. The integrated piezoelectric device exhibited a maximum voltage and current of 10.4 V and 2.3 μA, respectively. Furthermore, the robust integrity of the device components could provide high-precision sensitivity to perceive small pressures down to approximately 100 Pa while retaining a linear input-output relationship.

  15. Long-term liver-specific functions of hepatocytes in electrospun chitosan nanofiber scaffolds coated with fibronectin.

    Science.gov (United States)

    Rajendran, Divya; Hussain, Ali; Yip, Derek; Parekh, Amit; Shrirao, Anil; Cho, Cheul H

    2017-08-01

    In this study, a new 3D liver model was developed using biomimetic nanofiber scaffolds and co-culture system consisting of hepatocytes and fibroblasts for the maintenance of long-term liver functions. The chitosan nanofiber scaffolds were fabricated by the electrospinning technique. To enhance cellular adhesion and spreading, the surfaces of the chitosan scaffolds were coated with fibronectin (FN) by adsorption and evaluated for various cell types. Cellular phenotype, protein expression, and liver-specific functions were extensively characterized by immunofluorescent and histochemical stainings, albumin enzyme-linked immunosorbent assay and Cytochrome p450 detoxification assays, and scanning electron microscopy. The electrospun chitosan scaffolds exhibited a highly porous and randomly oriented nanofibrous structure. The FN coating on the surface of the chitosan nanofibers significantly enhanced cell attachment and spreading, as expected, as surface modification with this cell adhesion molecule on the chitosan surface is important for focal adhesion formation and integrin binding. Comparison of hepatocyte mono-cultures and co-cultures in 3D culture systems indicated that the hepatocytes in co-cultures formed colonies and maintained their morphologies and functions for prolonged periods of time. The 3D liver tissue model developed in this study will provide useful tools toward the development of engineered liver tissues for drug screening and tissue engineering applications. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 2119-2128, 2017. © 2017 Wiley Periodicals, Inc.

  16. Fabrication and characterization of vitamin B5 loaded poly (l-lactide-co-caprolactone)/silk fiber aligned electrospun nanofibers for schwann cell proliferation.

    Science.gov (United States)

    Bhutto, M Aqeel; Wu, Tong; Sun, Binbin; Ei-Hamshary, Hany; Al-Deyab, Salem S; Mo, Xiumei

    2016-08-01

    Bioengineering strategies for peripheral nerve regeneration have been focusing on the development of alternative treatments for nerve repair. In present study we have blended the Vitamin B5 (50mg) with 8% P(LLA-CL) and P(LLA-CL)/SF solutions and produced aligned electrospun nanofiber mashes and characterized the material for its physiochemical and mechanical characteristics. The vitamin loaded composites nanofibers showed tensile strength of 8.73±1.38 and 8.4±1.37 in P(LLA-CL)/Vt and P(LLA-CL)/SF/Vt nanofibers mashes, respectively. By the addition of vitamin B5 the P(LLA-CL) nanofibers become hydrophilic and the contact angle decreased from 96° to 0° in 6min of duration. The effect of vitamin B5 on Schwann cells proliferation and viability were analyzed by using MTT assay and the number of cells cultured on vitamin loaded nanofiber mashes was significantly higher than the without vitamin loaded nanofiber samples after 5th day (pvitamin release behavior was observed in PBS solution and released vitamin was calculated by revers phase HPLC method. The sustain release behavior of vitamin B5 were noted higher in P(LLA-CL)/Vt (80%) nanofibers as compared to P (LLA-CL)/SF/Vt (62%) nanofibers after 24h. The present work provided a basis for further studies of this novel aligned nanofibrous material in nerve tissue repair or regeneration. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Comparative performance of collagen nanofibers electrospun from different solvents and stabilized by different crosslinkers.

    Science.gov (United States)

    Fiorani, Andrea; Gualandi, Chiara; Panseri, Silvia; Montesi, Monica; Marcacci, Maurilio; Focarete, Maria Letizia; Bigi, Adriana

    2014-10-01

    Collagen electrospun scaffolds well reproduce the structure of the extracellular matrix (ECM) of natural tissues by coupling high biomimetism of the biological material with the fibrous morphology of the protein. Structural properties of collagen electrospun fibers are still a debated subject and there are conflicting reports in the literature addressing the presence of ultrastructure of collagen in electrospun fibers. In this work collagen type I was successfully electrospun from two different solvents, trifluoroethanol (TFE) and dilute acetic acid (AcOH). Characterization of collagen fibers was performed by means of SEM, ATR-IR, Circular Dichroism and WAXD. We demonstrated that collagen fibers contained a very low amount of triple helix with respect to pristine collagen (18 and 16% in fibers electrospun from AcOH and TFE, respectively) and that triple helix denaturation occurred during polymer dissolution. Collagen scaffolds were crosslinked by using 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC), a commonly employed crosslinker for electrospun collagen, and 1,4-butanediol diglycidyl ether (BDDGE), that was tested for the first time in this work as crosslinking agent for collagen in the form of electrospun fibers. We demonstrated that BDDGE successfully crosslinked collagen and preserved at the same time the scaffold fibrous morphology, while scaffolds crosslinked with EDC completely lost their porous structure. Mesenchymal stem cell experiments demonstrated that collagen scaffolds crosslinked with BDDGE are biocompatible and support cell attachment.

  18. Novel electrospun gelatin/oxycellulose nanofibers as a suitable platform for lung disease modeling

    Energy Technology Data Exchange (ETDEWEB)

    Švachová, Veronika, E-mail: xcsvachova@fch.vutbr.cz [Institute of Materials Chemistry, Brno University of Technology (Czech Republic); Vojtová, Lucy [CEITEC – Central European Institute of Technology, Brno University of Technology (Czech Republic); SCITEG, a.s., Brno (Czech Republic); Pavliňák, David [Department of Physical Electronics, Masaryk University (Czech Republic); Vojtek, Libor [Institute of Experimental Biology, Masaryk University (Czech Republic); Sedláková, Veronika [Department of Histology and Embryology, Masaryk University (Czech Republic); International Clinical Research, St. Anne' s University Hospital, Brno (Czech Republic); Hyršl, Pavel [Institute of Experimental Biology, Masaryk University (Czech Republic); Alberti, Milan [Department of Physical Electronics, Masaryk University (Czech Republic); Jaroš, Josef; Hampl, Aleš [Department of Histology and Embryology, Masaryk University (Czech Republic); International Clinical Research, St. Anne' s University Hospital, Brno (Czech Republic); Jančář, Josef [Institute of Materials Chemistry, Brno University of Technology (Czech Republic); CEITEC – Central European Institute of Technology, Brno University of Technology (Czech Republic); SCITEG, a.s., Brno (Czech Republic)

    2016-10-01

    Novel hydrolytically stable gelatin nanofibers modified with sodium or calcium salt of oxycellulose were prepared by electrospinning method. The unique inhibitory effect of these nanofibers against Escherichia coli bacteria was examined by luminometric method. Biocompatibility of these gelatin/oxycellulose nanofibers with eukaryotic cells was tested using human lung adenocarcinoma cell line NCI-H441. Cells firmly adhered to nanofiber surface, as determined by scanning electron microscopy, and no signs of cell dying were detected by fluorescent live/dead assay. We propose that the newly developed gelatin/oxycellulose nanofibers could be used as promising scaffold for lung disease modeling and anti-cancer drug testing. - Highlights: • Novel hydrolytically stable gelatin nanofibers modified with oxycellulose were prepared by electrospinning. • ATR–FTIR spectroscopy and EDX confirmed the presence of oxycellulose in the nanofibers. • Nanofibers modified with calcium salt of oxycellulose exhibited significant antibacterial properties. • Nanofibers modified with sodium salt of oxycellulose revealed excellent biocompatibility with cell line NCI-H441.

  19. A surface acoustic wave humidity sensor with high sensitivity based on electrospun MWCNT/Nafion nanofiber films

    International Nuclear Information System (INIS)

    Lei Sheng; Chen Dajing; Chen Yuquan

    2011-01-01

    Humidity detection has been widely used in a variety of fields. A humidity sensor with high sensitivity is reported in this paper. A surface acoustic wave resonator (SAWR) with high resonance frequency was fabricated as a basic sensitive component. Various nanotechnologies were used to improve the sensor's performance. A multi-walled carbon nanotube/Nafion (MWCNT/Nafion) composite material was prepared as humidity-sensitive films, deposited on the surface of an SAWR by the electrospinning method. The electrospun MWCNT/Nafion nanofiber films showed a three-dimensional (3D) porous structure, which was profitable for improving the sensor's performance. The new nano-water-channel model of Nafion was also applied in the humidity sensing process. Compared to other research, the present sensor showed excellent sensitivity (above 400 kHz/% relative humidity (RH) in the range from 10% RH to 80% RH), good linearity (R 2 > 0.98) and a short response time (∼3 s-63%).

  20. Synthesis of Porous NiO and ZnO Submicro- and Nanofibers from Electrospun Polymer Fiber Templates

    Directory of Open Access Journals (Sweden)

    Qiu Yejun

    2008-01-01

    Full Text Available Abstract Porous nickel oxide (NiO and zinc oxide (ZnO submicro- and nanofibers were synthesized by impregnating electrospun polyacrylonitrile (PAN fiber templates with corresponding metal nitrate aqueous solutions and subsequent calcination. The diameter of the NiO and ZnO fibers was closely related to that of the template fibers and larger diameters were obtained when using the template fibers with larger diameter. SEM results showed that the NiO and ZnO fibers have a large amount of pores with diameters ranging from 5 nm to 20 nm and 50 nm to 100 nm, respectively. Energy dispersive X-ray (EDX spectra and X-ray diffraction (XRD patterns testified that the obtained materials were NiO and ZnO with high purity.

  1. Superhydrophilic graphene oxide@electrospun cellulose nanofiber hybrid membrane for high-efficiency oil/water separation.

    Science.gov (United States)

    Ao, Chenghong; Yuan, Wei; Zhao, Jiangqi; He, Xu; Zhang, Xiaofang; Li, Qingye; Xia, Tian; Zhang, Wei; Lu, Canhui

    2017-11-01

    Inspired from fishscales, membranes with special surface wettability have been applied widely for the treatment of oily waste water. Herein, a novel superhydrophilic graphene oxide (GO)@electrospun cellulose nanofiber (CNF) membrane was successfully fabricated. This membrane exhibited a high separation efficiency, excellent antifouling properties, as well as a high flux for the gravity-driven oil/water separation. Moreover, the GO@CNF membrane was capable to effectively separate oil/water mixtures in a broad pH range or with a high concentration of salt, suggesting that this membrane was quite promising for future real-world practice in oil spill cleanup and oily wastewater treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Lignin-derived electrospun carbon nanofiber mats with supercritically deposited Ag nanoparticles for oxygen reduction reaction in alkaline fuel cells

    International Nuclear Information System (INIS)

    Lai, Chuilin; Kolla, Praveen; Zhao, Yong; Fong, Hao; Smirnova, Alevtina L.

    2014-01-01

    Highlights: • Electrospun carbon nanofiber mats were prepared from a natural product of lignin. • The freestanding mats were flexible with BET specific surface area of ∼583 m 2 /g. • The mats were surface-deposited with Ag nanoparticles via the scCO 2 method. • Novel electrocatalytic systems of Ag/ECNFs exhibited high activities towards ORR. - Abstract: Ag nanoparticles (AgNPs) (11, 15, and 25 wt.%) were deposited on the surface of the freestanding and mechanically flexible mats consisting of lignin-derived electrospun carbon nanofibers (ECNFs) by the supercritical CO 2 method followed by the thermal treated at 180 °C. The electrochemical activity of Ag/ECNFs electrocatalyst systems towards oxygen reduction reaction (ORR) was studied in 0.1 M KOH aqueous solution using the rotating disk/rotating ring disk electrode (RDE/RRDE) technique. The SEM, TEM, and XRD results indicated that, the spherical AgNPs were uniformly distributed on the ECNF surface with sizes in the range of 2-10 nm. The electrocatalytic results revealed that, all of the Ag/ECNFs systems exhibited high activity in ORR and demonstrated close-to-theoretical four-electron pathway. In particular, the mass activity of 15 wt.% Ag/ECNFs system was the highest (119 mA mg −1 ), exceeding that of HiSPEC 4100™ commercial Pt/C catalyst (98 mA mg −1 ). This study suggested that the lignin-derived ECNF mats surface-deposited with AgNPs would be promising as cost-effective and highly efficient electrocatalyst for ORR in alkaline fuel cells

  3. Abdominal closure reinforcement by using polypropylene mesh functionalized with poly-Ԑ-caprolactone nanofibers and growth factors for prevention of incisional hernia formation

    Directory of Open Access Journals (Sweden)

    Plencner M

    2014-07-01

    Full Text Available Martin Plencner,1,2,* Barbora East,3,* Zbynek Tonar,4 Martin Otáhal,5 Eva Prosecká,1,2 Michala Rampichová,2,6 Tomáš Krejčí,3 Andrej Litvinec,2,7 Matej Buzgo,2,6 Andrea Míčková,1,2,6 Alois Nečas,8 Jirí Hoch,3 Evžen Amler1,2,9 1Institute of Biophysics, Second Faculty of Medicine, Charles University in Prague, Prague, 2Laboratory of Tissue Engineering, Institute of Experimental Medicine, Academy of Sciences of the Czech Republic, Prague, 3Department of Surgery, Second Faculty of Medicine, Charles University in Prague, Prague, 4Biomedical Centre, Faculty of Medicine in Pilsen, Charles University in Prague, Pilsen, 5Department of Anatomy and Biomechanics, Faculty of Physical Education and Sport, Charles University in Prague, Prague, 6University Center for Energy Efficient Buildings, Czech Technical University in Prague, Buštehrad, 7Department of Breeding and Zoohygiene of Laboratory Animals, Institute of Physiology, Academy of Sciences of the Czech Republic, Prague, 8Department of Surgery and Orthopedics, Small Animal Clinic, Faculty of Veterinary Medicine, University of Veterinary and Pharmaceutical Science Brno, Central European Institute of Technology, Brno, 9Faculty of Biomedical Engineering, Czech Technical University in Prague, Kladno, Czech Republic *These authors contributed equally to this work Abstract: Incisional hernia affects up to 20% of patients after abdominal surgery. Unlike other types of hernia, its prognosis is poor, and patients suffer from recurrence within 10 years of the operation. Currently used hernia-repair meshes do not guarantee success, but only extend the recurrence-free period by about 5 years. Most of them are nonresorbable, and these implants can lead to many complications that are in some cases life-threatening. Electrospun nanofibers of various polymers have been used as tissue scaffolds and have been explored extensively in the last decade, due to their low cost and good biocompatibility. Their

  4. Electrospun nanofibers comprising of silk fibroin/gelatin for drug delivery applications: Thyme essential oil and doxycycline monohydrate release study.

    Science.gov (United States)

    Dadras Chomachayi, Masoud; Solouk, Atefeh; Akbari, Somaye; Sadeghi, Davoud; Mirahmadi, Fereshteh; Mirzadeh, Hamid

    2018-04-01

    In this study, a nanofibrous electrospun substrate based on the silk fibroin (SF) and gelatin (GT) polymers were prepared and evaluated. The SF/GT blended solutions were prepared with various ratios of GT in formic acid and electrospun to obtain bead-free fibers. Results showed that addition of GT to SF increased nanofiber's diameter, bulk hydrophilicity, surface wettability, mass loss percentage, but decreased Young's modulus, tensile strength, and porosity of the SF/GT mats. According to the obtained results, the mat containing 10% of GT was selected as the optimized mat for further studies and loaded with thyme essential oil (TEO) and doxycycline monohydrate (DCMH) as the antibacterial agents. Release studies showed a burst release of TEO from the mat within the first 3 h, while the DCMH had a sustained release during 48 h. In comparison to the TEO-loaded mat, the DCMH-loaded one showed larger inhibition zones against Staphylococcus aureus and Klebsiella pneumoniae bacteria. Meanwhile, cellular studies using mouse fibroblast L929 cells showed excellent cell-compatibility of TEO- and DCMH-loaded mats. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 106A: 1092-1103, 2018. © 2018 Wiley Periodicals, Inc.

  5. Experimental Investigation of the Properties of Electrospun Nanofibers for Potential Medical Application

    Directory of Open Access Journals (Sweden)

    Anhui Wang

    2015-01-01

    Full Text Available Polymer based nanofibers using ethylene-co-vinyl alcohol (EVOH were fabricated by electrospinning technology. The nanofibers were studied for potential use as dressing materials for skin wounds treatment. Properties closely related to the clinical requirements for wound dressing were investigated, including the fluid uptake ability (FUA, the water vapour transmission rate (WVTR, the bacteria control ability of nanofibers encapsulated with different antibacterial drugs, and Ag of various concentrations. Nanofibre degradation under different environmental conditions was also studied for the prospect of long term usage. The finding confirms the potential of EVOH nanofibers for wound dressing application, including the superior performance compared to cotton gauze and the strong germ killing capacity when Ag particles are present in the nanofibers.

  6. Novel electrospun gelatin/oxycellulose nanofibers as a suitable platform for lung disease modeling.

    Science.gov (United States)

    Švachová, Veronika; Vojtová, Lucy; Pavliňák, David; Vojtek, Libor; Sedláková, Veronika; Hyršl, Pavel; Alberti, Milan; Jaroš, Josef; Hampl, Aleš; Jančář, Josef

    2016-10-01

    Novel hydrolytically stable gelatin nanofibers modified with sodium or calcium salt of oxycellulose were prepared by electrospinning method. The unique inhibitory effect of these nanofibers against Escherichia coli bacteria was examined by luminometric method. Biocompatibility of these gelatin/oxycellulose nanofibers with eukaryotic cells was tested using human lung adenocarcinoma cell line NCI-H441. Cells firmly adhered to nanofiber surface, as determined by scanning electron microscopy, and no signs of cell dying were detected by fluorescent live/dead assay. We propose that the newly developed gelatin/oxycellulose nanofibers could be used as promising scaffold for lung disease modeling and anti-cancer drug testing. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Electrospun polyimide nanofiber-based nonwoven separators for lithium-ion batteries

    Science.gov (United States)

    Miao, Yue-E.; Zhu, Guan-Nan; Hou, Haoqing; Xia, Yong-Yao; Liu, Tianxi

    2013-03-01

    Polyimide (PI) nanofiber-based nonwovens have been fabricated via electrospinning for the separators of lithium-ion batteries (LIBs). Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and hot oven tests show that the PI nanofiber-based nonwovens are thermally stable at a high temperature of 500 °C while the commercial Celgard membrane exhibits great shrinkage at 150 °C and even goes melting over 167 °C, indicating a superior thermal stability of PI nanofiber-based nonwovens than that of the Celgard membrane. Moreover, the PI nanofiber-based nonwovens exhibit better wettability for the polar electrolyte compared to the Celgard membrane. The PI nanofiber-based nonwoven separators are also evaluated to have higher capacity, lower resistance and higher rate capability compared to the Celgard membrane separator, which proves that they are ideal candidates for separators of high-performance rechargeable LIBs.

  8. Abdominal closure reinforcement by using polypropylene mesh functionalized with poly-epsilon-caprolactone nanofibers and growth factors for prevention of incisional hernia formation

    Czech Academy of Sciences Publication Activity Database

    Plencner, M.; East, B.; Tonar, Z.; Otáhal, M.; Prosecká, E.; Rampichová, M.; Krejčí, T.; Litvinec, Andrej; Buzgo, M.; Míčková, A.; Nečas, A.; Hoch, J.; Amler, E.

    2014-01-01

    Roč. 9, č. 2014 (2014), s. 3263-3227 E-ISSN 1178-2013 Institutional support: RVO:67985823 Keywords : nanofibers * growth factors * surgical mesh Subject RIV: FP - Other Medical Disciplines Impact factor: 4.383, year: 2014

  9. Miniaturized pipette-tip-based electrospun polyacrylonitrile nanofibers for the micro-solid-phase extraction of nitro-based explosive compounds.

    Science.gov (United States)

    Tavengwa, Nikita Tawanda; Nyamukamba, Pardon; Cukrowska, Ewa; Chimuka, Luke

    2016-12-01

    In this study, a self-assembly of miniaturized pipette-tip-based solid-phase extraction for the simultaneous extraction of nitroaromatic compounds was developed, with electrospun polyacrylonitrile nanofibers used as sorbents. The electrospun polyacrylonitrile nanofibers were characterized by scanning electron microscopy, FTIR analysis and surface area analysis. Good linearities for the four nitroaromatic compounds (2,6-dinitrotoluene, 2-nitrotoluene, 3-nitrotoluene, and 4-nitrotoluene) were obtained in a range of 250-1000 μg/L with coefficients of determination > 0.99. The limits of detection of these analytes were between 21 and 38 μg/L. The results showed that the pipette-tip-based solid-phase extraction was effective in extracting nitrotoluenes in the pH regime of environmental interest (≈ 6). The investigation also revealed that the optimum mass of electrospun polyacrylonitrile nanofibers sorbent was 15 mg and 20 aspirating/dispensing cycles gave the maximum recovery of nitrotoluenes with 200 μL acetonitrile as the best eluting solvent. Moreover, the performance of the present method was studied for the extraction and determination of nitroaromatic compounds in real environmental water samples and good recoveries ranging from 70 to 115% were found, and respective relative standard deviations of <12% were obtained. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Preparation of Coaxial-Electrospun Poly[bis(p-methylphenoxy]phosphazene Nanofiber Membrane for Enzyme Immobilization

    Directory of Open Access Journals (Sweden)

    Xiao-Jun Huang

    2012-11-01

    Full Text Available A core/sheath nanofiber membrane with poly[bis(p-methylphenoxy]phospha-zene (PMPPh as the sheath and easily spinnable polyacrylonitrile (PAN as the core was prepared via a coaxial electrospinning process. Field-emission scanning electron microscopy and transmission electron microscopy were used to characterize the morphology of the nanofiber membrane. It was found that the concentration of the PAN spinning solution and the ratio of the core/sheath solution flow rates played a decisive role in the coaxial electrospinning process. In addition, the stabilized core/sheath PMPPh nanofiber membrane was investigated as a support for enzyme immobilization because of its excellent biocompatibility, high surface/volume ratio, and large porosity. Lipase from Candida rugosa was immobilized on the nanofiber membrane by adsorption. The properties of the immobilized lipase on the polyphosphazene nanofiber membrane were studied and compared with those of a PAN nanofiber membrane. The results showed that the adsorption capacity (20.4 ± 2.7 mg/g and activity retention (63.7% of the immobilized lipase on the polyphosphazene nanofiber membrane were higher than those on the PAN membrane.

  11. Electrospun Blank Nanocoating for Improved Sustained Release Profiles from Medicated Gliadin Nanofibers

    Directory of Open Access Journals (Sweden)

    Xinkuan Liu

    2018-03-01

    Full Text Available Nanomaterials providing sustained release profiles are highly desired for efficacious drug delivery. Advanced nanotechnologies are useful tools for creating elaborate nanostructure-based nanomaterials to achieve the designed functional performances. In this research, a modified coaxial electrospinning was explored to fabricate a novel core-sheath nanostructure (nanofibers F2, in which a sheath drug-free gliadin layer was successfully coated on the core ketoprofen (KET-gliadin nanocomposite. A monolithic nanocomposite (nanofibers F1 that was generated through traditional blending electrospinning of core fluid was utilized as a control. Scanning electron microscopy demonstrated that both nanofibers F1 and F2 were linear. Transmission electron microscopy verified that nanofibers F2 featured a clear core-sheath nanostructure with a thin sheath layer about 25 nm, whereas their cores and nanofibers F1 were homogeneous KET-gliadin nanocomposites. X-ray diffraction patterns verified that, as a result of fine compatibility, KET was dispersed in gliadin in an amorphous state. In vitro dissolution tests demonstrated that the thin blank nanocoating in nanofibers F2 significantly modified drug release kinetics from a traditional exponential equation of nanofibers F1 to a zero-order controlled release model, linearly freeing 95.7 ± 4.7% of the loaded cargoes over a time period of 16 h.

  12. Significant improvement of biocompatibility of polypropylene mesh for incisional hernia repair by using poly-ε-caprolactone nanofibers functionalized with thrombocyte-rich solution.

    Science.gov (United States)

    Plencner, Martin; Prosecká, Eva; Rampichová, Michala; East, Barbora; Buzgo, Matej; Vysloužilová, Lucie; Hoch, Jiří; Amler, Evžen

    2015-01-01

    Incisional hernia is the most common postoperative complication, affecting up to 20% of patients after abdominal surgery. Insertion of a synthetic surgical mesh has become the standard of care in ventral hernia repair. However, the implementation of a mesh does not reduce the risk of recurrence and the onset of hernia recurrence is only delayed by 2-3 years. Nowadays, more than 100 surgical meshes are available on the market, with polypropylene the most widely used for ventral hernia repair. Nonetheless, the ideal mesh does not exist yet; it still needs to be developed. Polycaprolactone nanofibers appear to be a suitable material for different kinds of cells, including fibroblasts, chondrocytes, and mesenchymal stem cells. The aim of the study reported here was to develop a functionalized scaffold for ventral hernia regeneration. We prepared a novel composite scaffold based on a polypropylene surgical mesh functionalized with poly-ε-caprolactone (PCL) nanofibers and adhered thrombocytes as a natural source of growth factors. In extensive in vitro tests, we proved the biocompatibility of PCL nanofibers with adhered thrombocytes deposited on a polypropylene mesh. Compared with polypropylene mesh alone, this composite scaffold provided better adhesion, growth, metabolic activity, proliferation, and viability of mouse fibroblasts in all tests and was even better than a polypropylene mesh functionalized with PCL nanofibers. The gradual release of growth factors from biocompatible nanofiber-modified scaffolds seems to be a promising approach in tissue engineering and regenerative medicine.

  13. Electrospun PEDOT:PSS/PVP Nanofibers for CO Gas Sensing with Quartz Crystal Microbalance Technique

    OpenAIRE

    Hong-Di Zhang; Xu Yan; Zhi-Hua Zhang; Gu-Feng Yu; Wen-Peng Han; Jun-Cheng Zhang; Yun-Ze Long

    2016-01-01

    Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/polyvinylpyrrolidone (PEDOT:PSS/PVP) composite nanofibers were successfully fabricated via electrospinning and used as a quartz crystal microbalance (QCM) sensor for detecting CO gas. The electrical property of individual PEDOT:PSS/PVP nanofibers was characterized and the room temperature resistivity was at the magnitude of 105 Ω·m. The QCM sensor based on PEDOT:PSS/PVP nanofibers was sensitive to low concentration (5–50 ppm) CO. In the ...

  14. Electrospun Chitosan-Gelatin Biopolymer Composite Nanofibers for Horseradish Peroxidase Immobilization in a Hydrogen Peroxide Biosensor

    Directory of Open Access Journals (Sweden)

    Siriwan Teepoo

    2017-10-01

    Full Text Available A biosensor based on chitosan-gelatin composite biopolymers nanofibers is found to be effective for the immobilization of horseradish peroxidase to detect hydrogen peroxide. The biopolymer nanofibers were fabricated by an electrospining technique. Upon optimization of synthesis parameters, biopolymers nanofibers, an average of 80 nm in diameter, were obtained and were then modified on the working electrode surface. The effects of the concentration of enzyme, pH, and concentration of the buffer and the working potential on the current response of the nanofibers-modified electrode toward hydrogen peroxide were optimized to obtain the maximal current response. The results found that horseradish peroxidase immobilization on chitosan-gelatin composite biopolymer nanofibers had advantages of fast response, excellent reproducibility, high stability, and showed a linear response to hydrogen peroxide in the concentration range from 0.1 to 1.7 mM with a detection limit of 0.05 mM and exhibited high sensitivity of 44 µA∙mM−1∙cm−2. The developed system was evaluated for analysis of disinfectant samples and showed good agreement between the results obtained by the titration method without significant differences at the 0.05 significance level. The proposed strategy based on chitosan-gelatin composite biopolymer nanofibers for the immobilization of enzymes can be extended for the development of other enzyme-based biosensors.

  15. Electrospun tin oxide/poly(3-hexylthiophene) nanofiber p-n diodes

    Science.gov (United States)

    Pinto, Nicholas

    2009-03-01

    Electrospinning is a simple technique used to prepare nanofibers of various materials, organic and inorganic. Some advantages of this method is that the nanofibers are orders of magnitude longer than that obtained via conventional means and it is easy to isolate individual nanofibers. We have used this technique to make nanoribbons of n-doped tin oxide (SnO2) and to make nanofibers of p-doped regio-regular poly(3hexylthiophene) (P3HT) in air and within seconds. Several p-n junction nanodiodes were fabricated by crossing individual nanofibers of P3HT with individual nanoribbons of SnO2 during the electrospinning process and electrically characterized them at room temperature. The SnO2 nanoribbons were fabricated first by electrospinning a precursor of SnO2 and then sintering them at 700 C to convert it to SnO2 before crossing them with P3HT nanofibers. The devices show clear evidence of rectification in air and in vacuum with a turn-on voltage of ˜0.4 V and with rectification ratios ˜10. Exposure of the diode to UV light increases the on-state current, while removing the light restores the device to its original state making it suitable as a reusable UV light sensor as well.

  16. Properties of Electrospun Nanofibers of Multi-Block Copolymers of [Poly-ε-caprolactone-b-poly(tetrahydrofuran-co-ε-caprolactone]m Synthesized by Janus Polymerization

    Directory of Open Access Journals (Sweden)

    Muhammad Ijaz Shah

    2017-10-01

    Full Text Available Novel biodegradable multiblock copolymers of [PCL-b-P(THF-co-CL]m with PCL fractions of 53.3 and 88.4 wt % were prepared by Janus polymerization of ε-caprolactone (CL and tetrahydrofuran (THF. Their electrospun mats were obtained with optimized parameters containing bead-free nanofibers whose diameters were between 290 and 520 nm. The mechanical properties of the nanofiber scaffolds were measured showing the tensile strength and strain at break of 8–10 MPa and 123–161%, respectively. Annealing improved their mechanical properties and their tensile strength and strain at break of the samples increased to 10–13 MPa and 267–338%, respectively. Due to the porous structure and crystallization in nanoscale confinement, the mechanical properties of the nanofiber scaffolds appeared as plastics, rather than as the elastomers observed in bulk thermal-molded film.

  17. Symbiotic organism search algorithm for simulation of J- V characteristics and optimizing internal parameters of DSSC developed using electrospun TiO2 nanofibers

    Science.gov (United States)

    Vinoth, S.; Kanimozhi, G.; Kumar, Harish; Srinadhu, E. S.; Satyanarayana, N.

    2017-12-01

    In the present investigation, the recently developed, simple, robust, and powerful metaheuristic symbiotic organism search (SOS) algorithm was used for simulation of J- V characteristics and optimizing the internal parameters of the dye-sensitized solar cells (DSSCs) fabricated using electrospun 1-D mesoporous TiO2 nanofibers as photoanode. The efficiency ( η = 5.80 %) of the DSSC made up of TiO2 nanofibers as photoanode is found to be ˜ 21.59% higher compared to the efficiency ( η = 4.77 %) of the DSSC made up of TiO2 nanoparticles as photoanode. The observed high efficiency can be attributed to high dye loading as well as high electron transport in the mesoporous 1-D TiO2 nanofibers. Further, the validity and advantage of SOS algorithm are verified by simulating J- V characteristics of DSSC with Lambert-W function.

  18. Poly(methyl vinyl ether-alt-maleic acid) and ethyl monoester as building polymers for drug-loadable electrospun nanofibers.

    Science.gov (United States)

    Mira, Amalia; Mateo, C Reyes; Mallavia, Ricardo; Falco, Alberto

    2017-12-08

    New biomaterials are sought for the development of bioengineered nanostructures. In the present study, electrospun nanofibers have been synthesized by using poly(methyl vinyl ether-alt-maleic acid) and poly(methyl vinyl ether-alt-maleic ethyl monoester) (PMVEMA-Ac and PMVEMA-ES, respectively) as building polymers for the first time. To further functionalize these materials, nanofibers of PMVEMA-Ac and PMVEMA-ES containing a conjugated polyelectrolyte (HTMA-PFP, blue emitter, and HTMA-PFNT, red emitter) were achieved with both forms maintaining a high solid state fluorescence yield without altered morphology. Also, 5-aminolevulinic acid (5-ALA) was incorporated within these nanofibers, where it remained chemically stable. In all cases, nanofiber diameters were less than 150 nm as determined by scanning and transmission electron microscopy, and encapsulation efficiency of 5-ALA was 97 ± 1% as measured by high-performance liquid chromatography. Both polymeric matrices showed rapid release kinetics in vertical cells (Franz cells) and followed Higuchi kinetics. In addition, no toxicity of nanofibers, in the absence of light, was found in HaCaT and SW480 cell lines. Finally, it was shown that loaded 5-ALA was functional, as it was internalized by cells in nanofiber-treated cultures and served as a substrate for the generation of protoporphyrin IX, suggesting these pharmaceutical vehicles are suitable for photodynamic therapy applications.

  19. Electrospun Gelatin/β-TCP Composite Nanofibers Enhance Osteogenic Differentiation of BMSCs and In Vivo Bone Formation by Activating Ca2+-Sensing Receptor Signaling

    Directory of Open Access Journals (Sweden)

    Xuehui Zhang

    2015-01-01

    Full Text Available Calcium phosphate- (CaP- based composite scaffolds have been used extensively for the bone regeneration in bone tissue engineering. Previously, we developed a biomimetic composite nanofibrous membrane of gelatin/β-tricalcium phosphate (TCP and confirmed their biological activity in vitro and bone regeneration in vivo. However, how these composite nanofibers promote the osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs is unknown. Here, gelatin/β-TCP composite nanofibers were fabricated by incorporating 20 wt% β-TCP nanoparticles into electrospun gelatin nanofibers. Electron microscopy showed that the composite β-TCP nanofibers had a nonwoven structure with a porous network and a rough surface. Spectral analyses confirmed the presence and chemical stability of the β-TCP and gelatin components. Compared with pure gelatin nanofibers, gelatin/β-TCP composite nanofibers caused increased cell attachment, proliferation, alkaline phosphatase activity, and osteogenic gene expression in rat BMSCs. Interestingly, the expression level of the calcium-sensing receptor (CaSR was significantly higher on the composite nanofibrous scaffolds than on pure gelatin. For rat calvarial critical sized defects, more extensive osteogenesis and neovascularization occurred in the composite scaffolds group compared with the gelatin group. Thus, gelatin/β-TCP composite scaffolds promote osteogenic differentiation of BMSCs in vitro and bone regeneration in vivo by activating Ca2+-sensing receptor signaling.

  20. Electrospun Gelatin/β-TCP Composite Nanofibers Enhance Osteogenic Differentiation of BMSCs and In Vivo Bone Formation by Activating Ca (2+) -Sensing Receptor Signaling.

    Science.gov (United States)

    Zhang, Xuehui; Meng, Song; Huang, Ying; Xu, Mingming; He, Ying; Lin, Hong; Han, Jianmin; Chai, Yuan; Wei, Yan; Deng, Xuliang

    2015-01-01

    Calcium phosphate- (CaP-) based composite scaffolds have been used extensively for the bone regeneration in bone tissue engineering. Previously, we developed a biomimetic composite nanofibrous membrane of gelatin/β-tricalcium phosphate (TCP) and confirmed their biological activity in vitro and bone regeneration in vivo. However, how these composite nanofibers promote the osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs) is unknown. Here, gelatin/β-TCP composite nanofibers were fabricated by incorporating 20 wt% β-TCP nanoparticles into electrospun gelatin nanofibers. Electron microscopy showed that the composite β-TCP nanofibers had a nonwoven structure with a porous network and a rough surface. Spectral analyses confirmed the presence and chemical stability of the β-TCP and gelatin components. Compared with pure gelatin nanofibers, gelatin/β-TCP composite nanofibers caused increased cell attachment, proliferation, alkaline phosphatase activity, and osteogenic gene expression in rat BMSCs. Interestingly, the expression level of the calcium-sensing receptor (CaSR) was significantly higher on the composite nanofibrous scaffolds than on pure gelatin. For rat calvarial critical sized defects, more extensive osteogenesis and neovascularization occurred in the composite scaffolds group compared with the gelatin group. Thus, gelatin/β-TCP composite scaffolds promote osteogenic differentiation of BMSCs in vitro and bone regeneration in vivo by activating Ca(2+)-sensing receptor signaling.

  1. Electrospun Polyacrylonitrile-Based Nanofibers Maintain Embryonic Stem Cell Stemness via TGF-Beta Signaling.

    Science.gov (United States)

    Liu, Shih-Ping; Lin, Chen-Huan; Lin, Shao-Ji; Fu, Ru-Huei; Huang, Yu-Chuen; Chen, Shih-Yin; Lin, Shinn-Zong; Hsu, Chung Y; Shyu, Woei-Cherng

    2016-04-01

    Embryonic stem cells (ESCs) and induced pluripotent stem cells (iPSCs) are capable of self-renewal and differentiation into any cell type, thus making them the focus of many clinical application studies. Culturing ESCs on mouse embryonic fibroblast-derived and cell-based feeder layers to maintain pluripotency is a standard laboratory procedure. However, xenogeneic contamination and the large amount of time required for feeder cell preparation are two challenges that encourage the use of a murine-based feeder layer. A novel biomaterial is required to replace the current cell-based feeder system. Toward this goal, we applied a combination of biocompatible polyacrylonitrile (PAN) and electrospinning technology to establish a non-cell-based feeder layer. According to results from stem cell marker staining, scanning electron microscopy, and embryoid body formation tests, optimal ESC stemness and pluripotency were noted in three electrospun groups (2, 4, and 8 minutes), with the longer electrospinning times producing higher feeder-layer densities. KEGG pathway microarray results identified TGF-beta signaling as one of the major deregulatory pathways on electrospun-based feeder layers. Western blot data indicate significant increases in TGF-beta receptor II, phosphorylated Smad3, and Nanog protein levels in the 4- and 8-minute electrospun-based feeder layer groups compared to the non-feeder layer group. Combined, the data suggest that electrospun-based feeder layers are good candidates for maintaining ESC and iPSC pluripotency in clinical applications.

  2. Effect of clay content on morphology and processability of electrospun keratin/poly(lactic acid) nanofiber.

    Science.gov (United States)

    Isarankura Na Ayutthaya, Siriorn; Tanpichai, Supachok; Sangkhun, Weradesh; Wootthikanokkhan, Jatuphorn

    2016-04-01

    This research work has concerned the development of volatile organic compounds (VOCs) removal filters from biomaterials, based on keratin extracted from chicken feather waste and poly(lactic acid) (PLA) (50/50%w/w) blend. Clay (Na-montmorillonite) was also added to the blend solution prior to carrying out an electro-spinning process. The aim of this study was to investigate the effect of clay content on viscosity, conductivity, and morphology of the electrospun fibers. Scanning electron micrographs showed that smooth and bead-free fibers were obtained when clay content used was below 2 pph. XRD patterns of the electrospun fibers indicated that the clay was intercalated and exfoliated within the polymers matrix. Percentage crystallinity of keratin in the blend increased after adding the clay, as evidenced from FTIR spectra and DSC thermograms. Transmission electron micrographs revealed a kind of core-shell structure with clay being predominately resided within the keratin rich shell and at the interfacial region. Filtration performance of the electrospun keratin/PLA fibers, described in terms of pressure drop and its capability of removing methylene blue, were also explored. Overall, our results demonstrated that it was possible to improve process-ability, morphology and filtration efficiency of the electrospun keratin fibers by adding a suitable amount of clay. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Study on structure, mechanical property and cell cytocompatibility of electrospun collagen nanofibers crosslinked by common agents.

    Science.gov (United States)

    Luo, Xueshi; Guo, Zhenzhao; He, Ping; Chen, Tian; Li, Lihua; Ding, Shan; Li, Hong

    2018-01-29

    Collagen electrospun scaffolds properly reproduce the framework of the extracellular matrix (ECM) of tissues that are natural with the fibrous morphology of the protein by coupling large biomimetism of the biological material. However, traditional solvents employed for collagen electrospinning lead to poor mechanical attributes and bad hydro-stability. In this work, by N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide hydrochloride with N-hydroxysulfosuccinimide (EDC-NHS), glutaraldehyde (GTA) and genipin (GP) respectively, electrospun collagen fibers cross-linked, effectively stabilized the fiber morphology over 2 months and improved the mechanical properties in both dry and wet state, especially EDC-NHS with large ultimate tensile stress and ε b . The secondary structure of collagen structure still remained and had no obvious difference among various crosslinked samples according to FTIR. On the cell assessment, electrospun collagen fibers crosslinked by EDC-NHS, GTA and GP, were found to support cell adhesion, spreading and proliferation of MC3T3-E1. By contrast, GTA was more effective in preserving explicit fibrous morphology with a relatively lower cell viability both in FBS and BSA soaked mats. Interestingly, GP also had the similar cytocompatibility of MC3T3-E1 as EDC-NHS did. The study proved the feasibility of chemical crosslinker to electrospun collagen for biomedical application. Copyright © 2017. Published by Elsevier B.V.

  4. Interfacial Properties of Lignin-Based Electrospun Nanofibers and Films Reinforced with Cellulose Nanocrystals

    Science.gov (United States)

    Mariko Ago; Joseph E. Jakes; Leena-Sisko Johansson; Sunkyu Park; Orlando J. Rojas

    2012-01-01

    Sub-100 nm resolution local thermal analysis, X-ray photoelectron spectroscopy (XPS), and water contact angle (WCA) measurements were used to relate surface polymer distribution with the composition of electrospun fiber mats and spin coated films obtained from aqueous dispersions of lignin, polyvinyl alcohol (PVA), and cellulose nanocrystal (CNC). Defect-free lignin/...

  5. Structure and Sound Absorption Properties of Spiral Vane Electrospun PVA/PEO Nanofiber Membranes

    Directory of Open Access Journals (Sweden)

    Huan Liu

    2018-02-01

    Full Text Available Noise pollution has become one of the four major pollution issues in the world and has drawn much attention recently. Controlling the sound source and using sound-absorbing materials reasonably is considered an effective way to reduce noise. Due to the high porosity and specific surface area, nanofibers membrane is widely used in the field of the sound absorption. Polyvinyl alcohol (PVA and Polyethylene oxide (PEO are both water-soluble polymers with good film-forming properties that can be mixed in any proportion. In this paper, nanofiber membranes were prepared by spiral vane electrospinning with different contents of PVA and PEO. The nanofibers membranes were characterized by Fourier Transform-Infrared (FT-IR, X-ray diffraction (XRD, 3D-M, and scanning electron microscopy (SEM. The sound absorption property of nanofibers membranes and the compositions (nanofiber membranes and needle punched non-woven fabric were tested with an impedance tube. The results demonstrate that the addition of PEO changed the morphological characteristics and construct of PVA, sound absorption properties had undergone great changes.

  6. Porosity characterization of biodegradable porous poly (L-lactic acid) electrospun nanofibers

    Science.gov (United States)

    Valipouri, Afsaneh; Gharehaghaji, Ali Akbar; Alirezazadeh, Azam; Ravandi, Seyed Abdolkarim Hosseini

    2017-12-01

    Poly-L lactic acid (PLLA) is one of the mostly used fibers in biomedical applications as a biodegradable and biocompatible material. Porosity and fiber diameter distribution are governing factors that determine the performance of nanofibers. Present work aims at investigating the process parameters that are affecting porosity and diameter distribution of PLLA nanofibers. PLLA nanofibers were fabricated through electrospinning method using the solution of PLLA polymer/dichloromethane (DCM). Nanofibers with various fiber diameter distribution and porosity were made by changing of process parameters such as spinning distance (5, 10 and 15 cm), voltage (11 and 15 kV), solution concentration (10, 11 and 12 wt%) and feeding rate (0.3, 0.4 and 0.7 ml h-1). Image processing techniques (with Matlab R2017), surface analysis (with Mountainsmap7) and diameter distribution analysis (with Measurement software) were used to examine surface morphology of samples. The results showed that the fiber diameter distribution becomes wider with increasing the applied voltage and reducing the spinning distance. In the other hand, coarse fibers possessed larger pores while having irregular and fewer pores in comparison to fine fibers. The most uniform nano-web with high porous nanofibers was attained by the choice of the process parameters at the voltage of 11 kV, spinning distance of 15 cm, feeding rate of 0.4 ml h-1 and solution concentration of 10 wt%.

  7. Piezoelectric properties of electrospun nanofibers of BaTiO3

    International Nuclear Information System (INIS)

    Carvalho, L.F.R.M.; Melo, G.F.; Goncalves, A.M.; Eiras, J.A.; Bretas, R.E.S.

    2016-01-01

    BaTiO3 nanofibers were produced by the electrospinning method from a mixture of a solution of the precursors Ba (CH 3 COO) 2 and [(CH 3 ) 2 CHO] 4 Ti in acetic acid and a solution of poly(vinylpyrrolidone) in ethanol. A voltage of 10 kV and a working distance of 4.6 cm were used for the electrospinning, at controlled room temperature and humidity of 21 °C and 60% respectively. Nanofibers as spun were dried in air on an air-circulating oven at 100 °C for one hour to remove residual solvent and were subsequently calcined at 750 °C during 2 h. The morphology, crystallographic structure and piezoelectric properties of the nanofibers were analyzed by scanning electron microscopy (SEM), X-ray angle (WAXS) and Piezoresponse Force Microscopy (PFM), respectively. The average diameter of the nanofibers was 414 nm with an aspect ratio of 40. By PFM, there was strong evidence that the nanofibers had piezoelectric activity. (author)

  8. Needleless electro-spun nanofibers used for filtration of small particles

    Directory of Open Access Journals (Sweden)

    Z. Zhang

    2013-08-01

    Full Text Available A composite aerosol filter media was prepared by depositing nanofibers on the non-woven fabrics substrate using needleless electrospinning technique. The polyvinyl alcohol nanofibers with mean diameters of ca. 100 nm were used as top layers. The filtration performance was evaluated by measuring the filtration of sodium chloride nanoparticles (75±20 nm through the filters. It was found that the filtration efficiency of the composite filter media for nanoparticles was increased along with the thickness of nanofibers mats which was controlled by the collection time during the electrospinning. The multi-layer arrangement for fabrication of the composite filter can achieve high filtration efficiency (up to 99.95% which was comparable to commercial high efficiency particulate air filters but with higher quality factor and less mass.

  9. Electro-spun organic nanofibers elaboration process investigations using comparative analytical solutions.

    Science.gov (United States)

    Colantoni, A; Boubaker, K

    2014-01-30

    In this paper Enhanced Variational Iteration Method, EVIM is proposed, along with the BPES, for solving Bratu equation which appears in the particular elecotrospun nanofibers fabrication process framework. Elecotrospun organic nanofibers, with diameters less than 1/4 microns have been used in non-wovens and filtration industries for a broad range of filtration applications in the last decade. Electro-spinning process has been associated to Bratu equation through thermo-electro-hydrodynamics balance equations. Analytical solutions have been proposed, discussed and compared. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Electrospun Polyacrylonitrile-Ionic Liquid Nanofibers for Superior PM2.5 Capture Capacity.

    Science.gov (United States)

    Jing, Lin; Shim, Kyubin; Toe, Cui Ying; Fang, Tim; Zhao, Chuan; Amal, Rose; Sun, Ke-Ning; Kim, Jung Ho; Ng, Yun Hau

    2016-03-23

    Ambient fine particulate matter (PM) affects both human health and climate. To reduce the PM2.5 (mass of particles below 2.5 μm in diameter) concentration of an individual's living environment, ionic liquid-modified polyacrylonitrile (PAN) nanofibers with superior PM2.5 capture capacity were prepared by electrospinning. Ionic liquid diethylammonium dihydrogen phosphate (DEAP) with high viscosity and hydrophilicity was involved during the electrospinning process. Observations by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and water contact angle measurement suggested that the modification of DEAP on PAN effectively altered the morphology (roughness) and surface properties (hydrophilicity) of the PAN nanofibers. The PM2.5 capture measurement was performed in a closed and static system, which mimicked the static hazy weather without wind flow. As a result, DEAP-modified PAN nanofibers exhibited significantly enhanced PM2.5 capture capacity compared to that of the bare PAN nanofibers. This can be attributed to the improved surface roughness (i.e., improved adsorption sites), hydrophilicity, and dipole moment of PAN upon DEAP modification.

  11. Biologically Active Polycaprolactone/Titanium Hybrid Electrospun Nanofibers for Hard Tissue Engineering

    DEFF Research Database (Denmark)

    Barakat, Nasser A. M.; Sheikh, Faheem A.; Al-Deyab, Salem S.

    2011-01-01

    body fluid. The introduced nanofibers have been prepared by electrospinning of a colloid composed of a polycaprolactone solution and titanium nanopowder. A mixed solvent composed of N,N dimethyl formammide and methyl chloride has been utilized to dissolve the polycaprolactone. The physiochemical...

  12. Antibacterial poly(ethylene oxide) electrospun nanofibers containing cinnamon essential oil/beta-cyclodextrin proteoliposomes.

    Science.gov (United States)

    Lin, Lin; Dai, Yajie; Cui, Haiying

    2017-12-15

    A novel antibacterial packaging material was engineered by incorporating cinnamon essential oil/β-cyclodextrin (CEO/β-CD) proteoliposomes into poly(ethylene oxide) (PEO) nanofibers by electrospinning technique. Herein, PEO was a stabilizing polymer and used as electrospinning polymeric matrix for the fabrication of CEO/β-CD proteoliposomes nanofibers. The nanoliposomes were inlaid with protein are defined as proteoliposomes. Taking advantage of bacterial protease secreted from Bacillus cereus (B. cereus), the controlled release of CEO from proteoliposomes was achieved via proteolysis of protein in proteoliposomes. The CEO/β-CD inclusion complex was prepared by the aqueous solution method and characterized by Raman and FTIR spectroscopy. After the treatment of CEO/β-CD proteoliposomes nanofibers packaging, the satisfactory antibacterial efficiency against B. cereus on beef was realized without any impact on sensory quality of beef. This study demonstrated that the CEO/β-CD proteoliposomes nanofibers can significantly extend the shelf life of beef and have potential application in active food packaging. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Emerging investigator series: development and application of polymeric electrospun nanofiber mats as equilibrium-passive sampler media for organic compounds.

    Science.gov (United States)

    Qian, Jiajie; Jennings, Brandon; Cwiertny, David M; Martinez, Andres

    2017-11-15

    We fabricated a suite of polymeric electrospun nanofiber mats (ENMs) and investigated their performance as next-generation passive sampler media for environmental monitoring of organic compounds. Electrospinning of common polymers [e.g., polyacrylonitrile (PAN), polymethyl methacrylate (PMMA), and polystyrene (PS), among others] yielded ENMs with reproducible control of nanofiber diameters (from 50 to 340 nm). The ENM performance was investigated initially with model hydrophilic (aniline and nitrobenzene) and hydrophobic (selected PCB congeners and dioxin) compounds, generally revealing fast chemical uptake into all of these ENMs, which was well described by a one compartment, first-order kinetic model. Typical times to reach 90% equilibrium (t 90% ) were ≤7 days under mixing conditions for all the ENMs and equilibrium timescales suggest that ENMs may be used in the field as an equilibrium-passive sampler, at least for our model compounds. Equilibrium partitioning coefficients (K ENM-W , L kg -1 ) averaged 2 and 4.7 log units for the hydrophilic and hydrophobic analytes, respectively. PAN, PMMA and PS were prioritized for additional studies because they exhibited not only the greatest capacity for simultaneous uptake of the entire model suite (log K ENM-W ∼1.5-6.2), but also fast uptake. For these optimized ENMs, the rates of uptake into PAN and PMMA were limited by aqueous phase diffusion to the nanofiber surface, and the rate-determining step for PS was analyte specific. Sorption isotherms also revealed that the environmental application of these optimized ENMs would occur within the linear uptake regime. We examined the ENM performance for the measurement of pore water concentrations from spiked soil and freshwater sediments. Soil and sediment studies not only yielded reproducible pore water concentrations and comparable values to other passive sampler materials, but also provided practical insights into ENM stability and fouling in such systems

  14. Improved supercapacitor performance of MnO2-electrospun carbon nanofibers electrodes by mT magnetic field

    Science.gov (United States)

    Zeng, Zheng; Liu, Yiyang; Zhang, Wendi; Chevva, Harish; Wei, Jianjun

    2017-08-01

    This work reports on a finding of mT magnetic field induced energy storage enhancement of MnO2-based supercapacitance electrodes (magneto-supercapacitor). Electrodes with MnO2 electrochemically deposited at electrospun carbon nanofibers (ECNFs) film are studied by cyclic voltammetry (CV), galvanostatic charge/discharge, electrochemical impedance spectroscopy (EIS), and life cycle stability tests in the presence/absence of milli-Tesla (mT) magnetic fields derived by Helmholtz coils. In the presence of a 1.34 mT magnetic field, MnO2/ECNFs shows a magneto-enhanced capacitance of 141.7 F g-1 vs. 119.2 F g-1 (∼19% increase) with absence of magnetic field at a voltage sweeping rate of 5 mV s-1. The mechanism of the magneto-supercapacitance is discussed and found that the magnetic susceptibility of the MnO2 significantly improves the electron transfer of a pseudo-redox reaction of Mn(IV)/Mn(III) at the electrode, along with the magnetic field induced impedance effect, which may greatly enhance the interface charge density, facilitate electrolyte transportation, and improve the efficiency of cation intercalation/de-intercalation of the pseudocapacitor under mT-magnetic field exposure, resulting in enhancement of energy storage capacitance and longer charge/discharge time of the MnO2/ECNFs electrode without sacrificing its life cycle stability.

  15. Drug loaded homogeneous electrospun PCL/gelatin hybrid nanofiber structures for anti-infective tissue regeneration membranes.

    Science.gov (United States)

    Xue, Jiajia; He, Min; Liu, Hao; Niu, Yuzhao; Crawford, Aileen; Coates, Phil D; Chen, Dafu; Shi, Rui; Zhang, Liqun

    2014-11-01

    Infection is the major reason for guided tissue regeneration/guided bone regeneration (GTR/GBR) membrane failure in clinical application. In this work, we developed GTR/GBR membranes with localized drug delivery function to prevent infection by electrospinning of poly(ε-caprolactone) (PCL) and gelatin blended with metronidazole (MNA). Acetic acid (HAc) was introduced to improve the miscibility of PCL and gelatin to fabricate homogeneous hybrid nanofiber membranes. The effects of the addition of HAc and the MNA content (0, 1, 5, 10, 20, 30, and 40 wt.% of polymer) on the properties of the membranes were investigated. The membranes showed good mechanical properties, appropriate biodegradation rate and barrier function. The controlled and sustained release of MNA from the membranes significantly prevented the colonization of anaerobic bacteria. Cells could adhere to and proliferate on the membranes without cytotoxicity until the MNA content reached 30%. Subcutaneous implantation in rabbits for 8 months demonstrated that MNA-loaded membranes evoked a less severe inflammatory response depending on the dose of MNA than bare membranes. The biodegradation time of the membranes was appropriate for tissue regeneration. These results indicated the potential for using MNA-loaded PCL/gelatin electrospun membranes as anti-infective GTR/GBR membranes to optimize clinical application of GTR/GBR strategies. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. Facile Synthesis of Indium Sulfide/Flexible Electrospun Carbon Nanofiber for Enhanced Photocatalytic Efficiency and Its Application.

    Science.gov (United States)

    Han, Liu; Dong, Haohao; Mao, Dong; Hua, Baolv; Li, Qinyu; Fang, Dong

    2017-01-01

    Heterojunction system has been proved as one of the best architectures for photocatalyst owing to extending specific surface area, expanding spectral response range, and increasing photoinduced charges generation, separation, and transmission, which can provide better light absorption range and higher reaction site. In this paper, Indium Sulfide/Flexible Electrospun Carbon Nanofiber (In 2 S 3 /CNF) heterogeneous systems were synthesized by a facile one-pot hydrothermal method. The results from characterizations of SEM, TEM, XRD, Raman, and UV-visible diffuse reflectance spectroscopy displayed that flower-like In 2 S 3 was deposited on the hair-like CNF template, forming a one-dimensional nanofibrous network heterojunction photocatalyst. And the newly prepared In 2 S 3 /CNF photocatalysts exhibit greatly enhanced photocatalytic activity compared to pure In 2 S 3 . In addition, the formation mechanism of the one-dimensional heterojunction In 2 S 3 /CNF photocatalyst is discussed and a promising approach to degrade Rhodamine B (RB) in the photocatalytic process is processed.

  17. Facile Synthesis of Indium Sulfide/Flexible Electrospun Carbon Nanofiber for Enhanced Photocatalytic Efficiency and Its Application

    Directory of Open Access Journals (Sweden)

    Liu Han

    2017-01-01

    Full Text Available Heterojunction system has been proved as one of the best architectures for photocatalyst owing to extending specific surface area, expanding spectral response range, and increasing photoinduced charges generation, separation, and transmission, which can provide better light absorption range and higher reaction site. In this paper, Indium Sulfide/Flexible Electrospun Carbon Nanofiber (In2S3/CNF heterogeneous systems were synthesized by a facile one-pot hydrothermal method. The results from characterizations of SEM, TEM, XRD, Raman, and UV-visible diffuse reflectance spectroscopy displayed that flower-like In2S3 was deposited on the hair-like CNF template, forming a one-dimensional nanofibrous network heterojunction photocatalyst. And the newly prepared In2S3/CNF photocatalysts exhibit greatly enhanced photocatalytic activity compared to pure In2S3. In addition, the formation mechanism of the one-dimensional heterojunction In2S3/CNF photocatalyst is discussed and a promising approach to degrade Rhodamine B (RB in the photocatalytic process is processed.

  18. Structure and Sound Absorption Properties of Spiral Vane Electrospun PVA/PEO Nanofiber Membranes

    OpenAIRE

    Huan Liu; Baoqi Zuo

    2018-01-01

    Noise pollution has become one of the four major pollution issues in the world and has drawn much attention recently. Controlling the sound source and using sound-absorbing materials reasonably is considered an effective way to reduce noise. Due to the high porosity and specific surface area, nanofibers membrane is widely used in the field of the sound absorption. Polyvinyl alcohol (PVA) and Polyethylene oxide (PEO) are both water-soluble polymers with good film-forming properties that can be...

  19. Layer-by-layer self-assembled chitosan coating on electrospun nanofibers

    OpenAIRE

    Croisier, Florence; Aqil, Abdelhafid; Detrembleur, Christophe; Jérôme, Christine

    2009-01-01

    By combining electrospinning technique and layer-by-layer deposition, we produced a new material made of multilayered, chitosan-based nanofibers. Layer-by-layer (LBL) is a well-known method for surface coating, based on electrostatic interactions. It enables the controllable deposition of a variety of polyions including synthetic and natural materials, with designable layer structure, defined wall thickness and size. Electrospinning (ESP) technique allows the fabrication of polymer fib...

  20. Polyhydroxybutyrate and phenolic compounds microalgae electrospun nanofibers: A novel nanomaterial with antibacterial activity.

    Science.gov (United States)

    Kuntzler, Suelen Goettems; Almeida, Ana Claudia Araujo de; Costa, Jorge Alberto Vieira; Morais, Michele Greque de

    2018-03-02

    Polymer nanofibers produced by electrospinning are promising for use in food packaging because of their nanometric diameter, which provides a barrier to external conditions above the possible incorporation of the active compounds. The microalga Spirulina sp. LEB 18 synthesizes bioproducts, such as polyhydroxybutyrate (PHB), which is biodegradable and has similar mechanical and thermal properties to polymers of petrochemical origin. Moreover, phenolic compounds of microalgae have antibacterial, antifungal, and antioxidant activities, which is a differential for the development of packaging. The objective of the study was to develop a nanomaterial with antibacterial action from bioproducts of microalgal origin. PHB nanofibers containing phenolic compounds presented average diameter of 810±85nm exhibited hydrophobicity, which gave protection to the food relative to the moisture outside the package. These nanofibers showed inhibition of the growth of Staphylococcus aureus ATCC 25923 with a zone of 7.5±0.4mm. Thermal and mechanical properties have confirmed the potential applicability of this material as food packaging. This new nanomaterial combines a packaging function to protect products and to be biodegradable with the antibacterial activity that prevents the proliferation of microorganisms and ensures the quality and preservation of food. Published by Elsevier B.V.

  1. Origin of piezoelectricity in an electrospun poly(vinylidene fluoride-trifluoroethylene) nanofiber web-based nanogenerator and nano-pressure sensor.

    Science.gov (United States)

    Mandal, Dipankar; Yoon, Sun; Kim, Kap Jin

    2011-06-01

    A single stage electrospinning process can give rise to preferentially oriented induced dipoles in poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] nanofibers. The piezoelectricity of as-electrospun P(VDF-TrFE) nanofiber webs opens up new possibilities for their use as a flexible nanogenerators and nano-pressure sensors. In this work, the origin of the piezoelectricity has been spotlighted by randomization of the induced dipoles at the Curie temperature and analyzed by polarized FT-IR spectroscopic techniques as well as by detecting the piezoelectric signal from a nano-pressure sensor. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Electrochemical Performance of Electrospun carbon nanofibers as free-standing and binder-free anodes for Sodium-Ion and Lithium-Ion Batteries

    International Nuclear Information System (INIS)

    Jin, Juan; Shi, Zhi-qiang; Wang, Cheng-yang

    2014-01-01

    Highlights: • Electrospun carbon nanofiber webs were prepared by pyrolysis of polyacrylonitrile. • The webs as binder-free and current collector-free electrodes for SIBs and LIBs. • Different layer spacing and pore size for Li and Na lead different electrochemical behavior. • Electrochemical performances of the electrodes were high. - Abstract: A series of hard carbon nanofiber-based electrodes derived from electrospun polyacrylonitrile (PAN) nanofibers (PAN-CNFs) have been fabricated by stabilization in air at about 280 °C and then carbonization in N 2 at heat treatment temperatures (HTT) between 800 and 1500 °C. The electrochemical performances of the binder-free, current collector-free carbon nanofiber-based anodes in lithium-ion batteries and sodium-ion batteries are systematically investigated and compared. We demonstrate the presence of similar alkali metal insertion mechanisms in both cases, but just the differences of the layer spacing and pore size available for lithium and sodium ion lead the discharge capacity delivered at sloping region and plateau region to vary from the kinds of alkali elements. Although the anodes in sodium-ion batteries show poorer rate capability than that in lithium-ion batteries, they still achieve a reversible sodium intercalation capacity of 275 mAh g −1 and similar cycling stability due to the conductive 3-D network, weakly ordered turbostratic structure and a large interlayer spacing between graphene sheets. The feature of high capacity and stable cycling performance makes PAN-CNFs to be promising candidates as electrodes in rechargeable sodium-ion batteries and lithium-ion batteries

  3. Electrospun Fe3O4/TiO2 hybrid nanofibers and their in vitro biocompatibility: prospective matrix for satellite cell adhesion and cultivation.

    Science.gov (United States)

    Amna, Touseef; Hassan, M Shamshi; Van Ba, Hoa; Khil, Myung-Seob; Lee, Hak-Kyo; Hwang, I H

    2013-03-01

    We report the fabrication of novel Fe3O4/TiO2 hybrid nanofibers with the improved cellular response for potential tissue engineering applications. In this study, Fe3O4/TiO2 hybrid nanofibers were prepared by facile sol-gel electrospinning using titanium isopropoxide and iron(III) nitrate nonahydrate as precursors. The obtained electrospun nanofibers were vacuum dried at 80 °C and then calcined at 500 °C. The physicochemical characterization of the synthesized composite nanofibers was carried out by scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy and X-ray diffraction pattern. To examine the in vitro cytotoxicity, satellite cells were treated with as-prepared Fe3O4/TiO2 and the viability of cells was analyzed by Cell Counting Kit-8 assay at regular time intervals. The morphological features of unexposed satellite cells and exposed to Fe3O4/TiO2 composite were examined with a phase contrast microscope whereas the quantification of cell viability was carried out via confocal laser scanning microscopy. The morphology of the cells attached to hybrid matrix was observed by Bio-SEM. Cytotoxicity experiments indicated that the satellite cells could attach to the Fe3O4/TiO2 composite nanofibers after being cultured. We observed that Fe3O4-TiO2 composite nanofibers could support cell adhesion and growth. Results from this study therefore suggest that Fe3O4/TiO2 composite scaffold with small diameters (approximately 200 nm) can mimic the natural extracellular matrix well and provide possibilities for diverse applications in the field of tissue engineering and regenerative medicine. Copyright © 2012 Elsevier B.V. All rights reserved.

  4. Electrospun hydrophilic fumed silica/polyacrylonitrile nanofiber-based composite electrolyte membranes

    International Nuclear Information System (INIS)

    Jung, Hong-Ryun; Ju, Dong-Hyuk; Lee, Wan-Jin; Zhang, Xiangwu; Kotek, Richard

    2009-01-01

    Hydrophilic fumed silica (SiO 2 )/polyacrylonitrile (PAN) composite electrolyte membranes were prepared by electrospinning composite solutions of SiO 2 and PAN in N,N-dimethylformamide (DMF). Among electrospinning solutions with various SiO 2 contents, the 12 wt% SiO 2 in PAN solution has highest zeta potential (-40.82 mV), and exhibits the best dispersibility of SiO 2 particles. The resultant 12 wt% SiO 2 /PAN nanofiber membrane has the smallest average fiber diameter, highest porosity, and largest specific surface area. In addition, this membrane has a three-dimensional network structure, which is fully interconnected with combined mesopores and macropores because of a good SiO 2 dispersion. Composite electrolyte membranes were prepared by soaking these porous nanofiber membranes in 1 M lithium hexafluorophosphate (LiPF 6 ) in ethylene carbonate (EC)/dimethyl carbonate (DMC) (1:1 vol%). It is found that 12 wt% SiO 2 /PAN electrolyte membrane has the highest conductivity (1.1 x 10 -2 S cm -1 ) due to the large liquid electrolyte uptake (about 490%). In addition, the electrochemical performance of composite electrolyte membranes is also improved after the introduction of SiO 2 . For initial cycle, 12 wt% SiO 2 /PAN composite electrolyte membrane delivers the discharge capacity of 139 mAh g -1 as 98% of theoretical value, and still retains a high value of 127 mAh g -1 as 89% at 150th cycle, which is significantly higher that of pure PAN nanofiber-based electrolyte membranes.

  5. Effect of Electrospun Nanofibers on the Short Beam Strength of Laminated Fiberglass Composite

    Science.gov (United States)

    Shinde, Dattaji K.

    High specific modulus and strength are the most desirable properties for the material used in structural applications. Composite materials exhibit these properties and over the last decade, their usage has increased significantly, particularly in automotive, defense, and aerospace applications. The major cause of failures in composite laminates is due to delaminations. Delamination in composite laminates can occur due to fatigue, low velocity impact and other loadings modes. Conventional methods like "through-the-thickness stitching" or "Z-Pinning" have limitations for improving flexural and interlaminar properties in woven composites due to the fact that while improving interlaminar properties, the presence of stitches or Z pins affects in-plane properties. This study investigates the flexural behavior of fiberglass composites interleaved with non-woven Tetra Ethyl Orthosilicate (TEOS) electrsopsun nanofibers (ENFs). TEOS ENFs were manufactured using an electrospinning technique and then sintered. Nanoengineered beams were fabricated by interleaving TEOS ENFs between the laminated fiberglass composites to improve the flexural properties. TEOS ENFs, resin film, and failed fiberglass laminated composites with and without nanofibers were characterized using SEM Imaging and ASTM standard testing methods. A hybrid composite was made by interleaving a non-woven sheet of TEOS ENFs between the fiberglass laminates with additional epoxy resin film and fabricated using the out of autoclave vacuum bagging method. Four commonly used stacking sequences of fiberglass laminates with and without nanofibers were used to study the progressive failure and deformation mechanics under flexural loadings. The experimental study has shown significant improvements in short beam strength and strain energy absorption in the nanoengineered laminated fiberglass composites before complete failure. The modes were investigated by performing detailed fractographic examination of failed specimens

  6. Electrospun core/shell nanofibers: a promising system for cartilage and tissue engineering?

    Czech Academy of Sciences Publication Activity Database

    Amler, Evžen; Míčková, Andrea; Buzgo, Matej

    2013-01-01

    Roč. 8, č. 4 (2013), s. 509-512 ISSN 1743-5889 Grant - others:GA UK(CZ) 330611; GA UK(CZ) 384311; GA UK(CZ) 626012; GA UK(CZ) 648112; GA MŠk(CZ) ME10145; GA MZd(CZ) NT12156 Institutional research plan: CEZ:AV0Z50390512; CEZ:AV0Z50390703 Keywords : core-shell nanofibers * electrospinning * drug delivery Subject RIV: FP - Other Medical Disciplines Impact factor: 5.824, year: 2013

  7. Characterization of carbon nanofiber mats produced from electrospun lignin-g-polyacrylonitrile copolymer.

    Science.gov (United States)

    Youe, Won-Jae; Lee, Soo-Min; Lee, Sung-Suk; Lee, Seung-Hwan; Kim, Yong Sik

    2016-01-01

    The graft copolymerization of acrylonitrile (AN) onto methanol-soluble kraft lignin (ML) was achieved through a two-step process in which AN was first polymerized with an α,α'-azobisisobutyronitrile initiator, followed by radical coupling with activated ML. A carbon nanofiber material was obtained by electrospinning a solution of this copolymer in N,N-dimethylformamide, then subjecting it to a heat treatment including thermostabilization at 250°C and subsequent carbonization at 600-1400°C. Increasing the carbonization temperature was found to increase the carbon content of the resulting carbon nanofibers from 70.5 to 97.1%, which had the effect of increasing their tensile strength from 35.2 to 89.4 MPa, their crystallite size from 13.2 to 19.1 nm, and their electrical conductivity from ∼0 to 21.3 Scm(-1). The morphology of the mats, in terms of whether they experienced beading or not, was found to be dependent on the concentration of the initial electrospinning solution. From these results, it is proposed that these mats could provide the basis for a new class of carbon fiber material. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Electrospun ZnO/Bi2O3 Nanofibers with Enhanced Photocatalytic Activity

    Directory of Open Access Journals (Sweden)

    Yingying Yang

    2014-01-01

    Full Text Available ZnO/Bi2O3 nanofibers were synthesized by a simple electrospinning method and both the UV and visible light responsive photocatalytic properties were studied by the decolorization of RhB dye. Thermogravimetric analysis/differential thermal analysis (TGA-DTA, X-ray diffraction (XRD, scanning electron microscope (SEM, and UV-vis diffuse reflectance spectra (DRS were employed to study the structure, morphology, and optical properties of the ZnO/Bi2O3 nanofibers, respectively. The relationship between the ZnO/Bi2O3 ratio and photocatalytic activity was also studied, and the composite with a molar ratio of 23 : 1 demonstrated the best activity under both excitations. The photocatalytic mechanisms for the composite fibers can be described as the direct photocatalysis under UV excitation and photosensitation for visible light irradiation. The enhanced photocatalytic activities can be ascribed to the effective electron-hole pairs separation that leads to the promoted photocatalytic efficiency.

  9. Study of Hydrophilic Electrospun Nanofiber Membranes for Filtration of Micro and Nanosize Suspended Particles

    Directory of Open Access Journals (Sweden)

    Nurxat Nuraje

    2013-11-01

    Full Text Available Polymeric nanofiber membranes of polyvinyl chloride (PVC blended with polyvinylpyrrolidone (PVP were fabricated using an electrospinning process at different conditions and used for the filtration of three different liquid suspensions to determine the efficiency of the filter membranes. The three liquid suspensions included lake water, abrasive particles from a water jet cutter, and suspended magnetite nanoparticles. The major goal of this research work was to create highly hydrophilic nanofiber membranes and utilize them to filter the suspended liquids at an optimal level of purification (i.e., drinkable level. In order to overcome the fouling/biofouling/blocking problems of the membrane, a coagulation process, which enhances the membrane’s efficiency for removing colloidal particles, was used as a pre-treatment process. Two chemical agents, Tanfloc (organic and Alum (inorganic, were chosen for the flocculation/coagulation process. The removal efficiency of the suspended particles in the liquids was measured in terms of turbidity, pH, and total dissolved solids (TDS. It was observed that the coagulation/filtration experiments were more efficient at removing turbidity, compared to the direct filtration process performed without any coagulation and filter media.

  10. Lysozyme-immobilized electrospun PAMA/PVA and PSSA-MA/PVA ion-exchange nanofiber for wound healing.

    Science.gov (United States)

    Tonglairoum, Prasopchai; Ngawhirunpat, Tanasait; Rojanarata, Theerasak; Opanasopit, Praneet

    2014-08-27

    Abstract This research was aimed to develop the lysozyme immobilized ion-exchange nanofiber mats for wound healing. To promote the healing process, the PSSA-MA/PVA and PAMA ion-exchange nanofiber mats were fabricated to mimic the extracellular matrix structure using electrospinning process followed by thermally crosslinked. Lysozyme was immobilized on the ion-exchane nanofibers by an adsorption method. The ion-exchange nanofibers were investigated using SEM, FTIR and XRPD. Moreover, the lysozyme-immobilized ion-exchange nanofibers were further investigated for lysozyme content and activity, lysozyme release and wound healing activity. The fiber diameters of the mats were in the nanometer range. Lysozyme was gradually absorbed into the PSSA-MA/PVA nanofiber with higher extend than that is absorbed on the PAMA/PVA nanofiber and exhibited higher activity than lysozyme-immobilized PAMA/PVA nanofiber. The total contents of lysozyme on the PSSA-MA/PVA and PAMA/PVA nanofiber were 648 and 166 µg/g, respectively. FTIR and lysozyme activity results confirmed the presence of lysozyme on the nanofiber mats. The lysozyme was released from the PSSA-MA/PVA and PAMA/PVA nanofiber in the same manner. The lysozyme-immobilized PSSA-MA/PVA nanofiber mats and lysozyme-immobilized PAMA/PVA nanofiber mats exhibited significantly faster healing rate than gauze and similar to the commercial antibacterial gauze dressing. These results suggest that these nanofiber mats could provide the promising candidate for wound healing application.

  11. Ketoprofen-loaded Eudragit electrospun nanofibers for the treatment of oral mucositis

    Directory of Open Access Journals (Sweden)

    Reda RI

    2017-03-01

    Full Text Available Rana Ihab Reda,1 Ming Ming Wen,2 Amal Hassan El-Kamel1 1Department of Pharmaceutics, Faculty of Pharmacy, Alexandria University, 2Department of Pharmaceutics, Faculty of Pharmacy and Drug Manufacturing, Pharos University in Alexandria, Alexandria, Egypt Purpose: The purpose of this study was to formulate ketoprofen (KET-loaded Eudragit L and Eudragit S nanofibers (NFs by the electrospinning technique for buccal administration to treat oral mucositis as a safe alternative to orally administered KET, which causes gastrointestinal tract (GIT side effects. Materials and methods: NFs were prepared by electrospinning using Eudragit L and Eudragit S. Several variables were evaluated to optimize NF formulation, such as polymer types and concentrations, applied voltage, flow rate and drug concentrations. Differential scanning calorimetry (DSC, Fourier transform infrared spectroscopy (FTIR and scanning electron microscopy (SEM and analyses of drug contents, hydration capacity, surface pH, drug release and ex vivo permeation were performed to evaluate the NFs. The selected formulation (F1 was evaluated in vivo on induced oral mucositis in rabbits. Results: SEM revealed that 20% polymer formed smooth and bead-free NFs. DSC results confirmed the amorphous nature of KET in the NFs. FTIR confirmed hydrogen bond formation between the drug and polymer, which stabilized the NFs. Both formulations (F1 and F2 had an acceptable surface pH. The drug loading was >90%. The amount of KET released from NF formulations was statistically significantly higher (P≤0.001 than that released from the corresponding solvent-casted films. The complete release of KET from F1 occurred within 2 hours. Ex vivo permeation study revealed that only a small fraction of drug permeated from F1, which was a better candidate than F2 for local buccal delivery. In vivo evaluation of F1 on oral mucositis induced in rabbits demonstrated that F1 reduced the clinical severity of mucositis in

  12. Br-PADAP embedded in cellulose acetate electrospun nanofibers: Colorimetric sensor strips for visual uranyl recognition.

    Science.gov (United States)

    Hu, Lin; Yan, Xue-Wu; Li, Qi; Zhang, Xue-Ji; Shan, Dan

    2017-05-05

    In this work, a new visual colorimetric strip based on cellulose acetate nanofiber mats modified by 2-(5-Bromo-2-pyridylazo)-5-(diethylamino) phenol was successfully prepared via electrospinning technology. The prepared colorimetric strip showed high sensitivity towards UO 2 2+ with the yellow-to-purple color change signal. Upon the optimal conditions of solution pH at 6.0 and response time for 80min, the detection limit for UO 2 2+ can reach 50 ppb. Moreover, the strip also exhibited excellent anti-interference ability in the presence of other metal ions. In order to achieve the quantitative detection for UO 2 2+ , a color-differentiation map was established, which was prepared from converted H values. Finally, the strip was also used to detect UO 2 2+ in the seawater and showed high sensitivity. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Synthesis of Fe3O4/Polyacrylonitrile Composite Electrospun Nanofiber Mat for Effective Adsorption of Tetracycline.

    Science.gov (United States)

    Liu, Qing; Zhong, Lu-Bin; Zhao, Quan-Bao; Frear, Craig; Zheng, Yu-Ming

    2015-07-15

    Novel Fe3O4/polyacrylonitrile (PAN) composite nanofibers (NFs) were prepared by a simple two-step process, an electrospinning and solvothermal method. Characterization by field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) demonstrated formation of a uniform nanoparticles coating (about 20 nm in thickness) on the PAN nanofiber backbone. The coating was constructed by well-crystallized cubic phase Fe3O4 nanoparticles as examined by X-ray diffraction spectroscopy (XRD). The coating doubled the specific surface area of NFs, from 8.4 to 17.8 m2 g(-1), as confirmed by nitrogen sorption isotherm analysis. To evaluate the feasibility of Fe3O4/PAN composite NFs as a potential adsorbent for antibiotic removal, batch adsorption experiments were conducted using tetracycline (TC) as the model antibiotic molecule. The results showed that Fe3O4/PAN composite NFs were effective in removing TC with no impactful loss of Fe in the pH regime of environmental interest (5-8). The adsorption of TC onto Fe3O4/PAN composite NFs better fitted the pseudo-second-order kinetics model, and the maximum adsorption capacity calculated from Langmuir isotherm model was 257.07 mg g(-1) at pH 6. The composite NFs also exhibited good regenerability over repeated adsorption/desorption cycles. Surface complexation between TC and the composite NFs contributed most to the adsorption as elucidated by X-ray photoelectron spectroscopy (XPS). This highly effective and novel adsorbent can be easily modularized and separated, promising its huge potential in drinking and wastewater treatment for antibiotic removal.

  14. Dehydration of bacteriophages in electrospun nanofibers: effect of excipients in polymeric solutions

    Science.gov (United States)

    Koo, Charmaine K. W.; Senecal, Kris; Senecal, Andre; Nugen, Sam R.

    2016-12-01

    Bacteriophages are viruses capable of infecting and lysing target bacterial cells; as such they have potential applications in agriculture for decontamination of foods, food contact surfaces and food rinse water. Although bacteriophages can retain infectivity long-term using lyophilized storage, the process of freeze-drying can be time consuming and expensive. In this study, electrospinning was used for dehydrating bacteriophages in polyvinylpyrrolidone polymer solutions with addition of excipients (sodium chloride, magnesium sulfate, Tris-HCl, sucrose) in deionized water. The high voltage dehydration reduced the infectivity of bacteriophages following electrospinning, with the damaging effect abated with addition of storage media (SM) buffer and sucrose. SM buffer and sucrose also provided the most protection over extended storage (8 weeks; 20 °C 1% relative humidity) by mitigating environmental effects on the dried bacteriophages. Magnesium sulfate however provided the least protection due to coagulation effects of the ion, which can disrupt the native conformation of the bacteriophage protein coat. Storage temperatures (20 °C, 4 °C and -20 °C 1% relative humidity) had a minimal effect while relative humidity had substantial effect on the infectivity of bacteriophages. Nanofibers stored in higher relative humidity (33% and 75%) underwent considerable damage due to extensive water absorption and disruption of the fibers. Overall, following storage of nanofiber mats for eight weeks at ambient temperatures, high infective phage concentrations (106-107 PFU ml-1) were retained. Therefore, this study provided valuable insights on preservation and dehydration of bacteriophages by electrospinning in comparison to freeze drying and liquid storage, and the influence of excipients on the viability of bacteriophages.

  15. Electrospun Hydroxyapatite-Containing Chitosan Nanofibers Crosslinked with Genipin for Bone Tissue Engineering

    Science.gov (United States)

    Frohbergh, Michael E.; Katsman, Anna; Botta, Gregory P.; Lazarovici, Phillip; Schauer, Caroline L.; Wegst, Ulrike G. K.; Lelkes, Peter I.

    2012-01-01

    Reconstruction of large bone defects remains problematic in orthopedic and craniofacial clinical practice. Autografts are limited in supply and are associated with donor site morbidity while other materials show poor integration with the host’s own bone. This lack of integration is often due to the absence of periosteum, the outer layer of bone that contains osteoprogenitor cells and is critical for the growth and remodeling of bone tissue. In this study we developed a one-step platform to electrospin nanofibrous scaffolds from chitosan, which also contain hydroxyapatite nanoparticles and are crosslinked with genipin. We hypothesized that the resulting composite scaffolds represent a microenvironment that emulates the physical, mineralized structure and mechanical properties of non-weight bearing bone extracellular matrix while promoting osteoblast differentiation and maturation similar to the periosteum. The ultrastructure and physicochemical properties of the scaffolds were studied using scanning electron microscopy and spectroscopic techniques. The average fiber diameters of the electrospun scaffolds were 227±154 nm as spun, and increased to 335±119 nm after crosslinking with genipin. Analysis by X-ray diffraction, Fourier transformed infrared spectroscopy and energy dispersive spectroscopy confirmed the presence of characteristic features of hydroxyapatite in the composite chitosan fibers. The Young’s modulus of the composite fibrous scaffolds was 142±13 MPa, which is similar to that of the natural periosteum. Both pure chitosan scaffolds and composite hydroxyapatite-containing chitosan scaffolds supported adhesion, proliferation and osteogenic differentiation of mouse 7F2 osteoblast-like cells. Expression and enzymatic activity of alkaline phosphatase, an early osteogenic marker, were higher in cells cultured on the composite scaffolds as compared to pure chitosan scaffolds, reaching a significant, 2.4 fold, difference by day 14 (phydroxyapatite

  16. Electrospun hydroxyapatite-containing chitosan nanofibers crosslinked with genipin for bone tissue engineering.

    Science.gov (United States)

    Frohbergh, Michael E; Katsman, Anna; Botta, Gregory P; Lazarovici, Phillip; Schauer, Caroline L; Wegst, Ulrike G K; Lelkes, Peter I

    2012-12-01

    Reconstruction of large bone defects remains problematic in orthopedic and craniofacial clinical practice. Autografts are limited in supply and are associated with donor site morbidity while other materials show poor integration with the host's own bone. This lack of integration is often due to the absence of periosteum, the outer layer of bone that contains osteoprogenitor cells and is critical for the growth and remodeling of bone tissue. In this study we developed a one-step platform to electrospin nanofibrous scaffolds from chitosan, which also contain hydroxyapatite nanoparticles and are crosslinked with genipin. We hypothesized that the resulting composite scaffolds represent a microenvironment that emulates the physical, mineralized structure and mechanical properties of non-weight bearing bone extracellular matrix while promoting osteoblast differentiation and maturation similar to the periosteum. The ultrastructure and physicochemical properties of the scaffolds were studied using scanning electron microscopy and spectroscopic techniques. The average fiber diameters of the electrospun scaffolds were 227 ± 154 nm as spun, and increased to 335 ± 119 nm after crosslinking with genipin. Analysis by X-ray diffraction, Fourier transformed infrared spectroscopy and energy dispersive spectroscopy confirmed the presence of characteristic features of hydroxyapatite in the composite chitosan fibers. The Young's modulus of the composite fibrous scaffolds was 142 ± 13 MPa, which is similar to that of the natural periosteum. Both pure chitosan scaffolds and composite hydroxyapatite-containing chitosan scaffolds supported adhesion, proliferation and osteogenic differentiation of mouse 7F2 osteoblast-like cells. Expression and enzymatic activity of alkaline phosphatase, an early osteogenic marker, were higher in cells cultured on the composite scaffolds as compared to pure chitosan scaffolds, reaching a significant, 2.4 fold, difference by day 14 (p

  17. A flexible electrostatic kinetic energy harvester based on electret films of electrospun nanofibers

    Science.gov (United States)

    Lu, Y.; Capo-Chichi, M.; Leprince-Wang, Y.; Basset, P.

    2018-01-01

    This paper reports a paper-based electrostatic kinetic energy harvester (e-KEH) implementing multilayered electret films based on electrospun nanofibrous material. It is the first time that a fully flexible electret-based e-KEH is reported. The proposed electret, PVDF-PTFD nanofibrous covered by Parylene C, has a faster stabilization of surface potential than a planar thin film of Parylene C, and a higher stability of charge storage. With a maximum force of 0.5 N and a 3-layer electret, the device capacitance increases from 25 to 100 pF during a pressing operation. Working with the optimal resistive load of 16 MΩ, the device pressed manually delivers a peak instantaneous power up to 45.6 μW and an average energy of 54 nJ/stroke, corresponding to a peak instantaneous power density of 7.3 μW cm‑2 and an average energy density of 8.6 nJ cm‑2/stroke. Within 450 manual strokes, a 10 nF capacitor is charged up to 8.5 V by the prototype through a full-wave diode bridge. On a 1 μF capacitor, the energy delivery of 9.9 nJ/stroke has been obtained with a 10 Hz pressing movement excited by a vibrator with a maximum force of 0.5 N.

  18. Development of electrospun nanofiber composites for pointof-use water treatment

    Science.gov (United States)

    Peter, Katherine T.

    A range of chemical pollutants now contaminate drinking water sources and present a public health concern, including organic compounds, such as pharmaceuticals and pesticides, and both metalloids and heavy metals, such as arsenic and lead. Metalloids and heavy metals have been detected in private drinking water wells, which do not fall under federal drinking water regulations, as well as in urban tap water, due to the introduction of contamination to the drinking water distribution system. Further, many so-called "emerging organic contaminants," which are present in drinking water sources at detectable levels but have unknown long-term health implications, do not fall under federal drinking water regulations. To protect the health of consumers, drinking water treatment at the point-of-use (POU) (i.e., the tap) is essential. Next-generation POU treatment technologies must require minimal energy inputs, be simple enough to permit broad application among different users, and be easily adaptable for removal of a wide range of pollutants. Nanomaterials, such as carbon nanotubes and iron oxide nanoparticles, are ideal candidates for next-generation drinking water treatment, as they exhibit unique, high reactivity and necessitate small treatment units. However, concerns regarding water pressure requirements and nanomaterial release into the treated supply limit their application in traditional reactor designs. To bridge the gap between potential and practical application of nanomaterials, this study utilizes electrospinning to fabricate composite nanofiber filters that effectively deploy nanomaterials in drinking water treatment. In electrospinning, a high voltage draws a polymer precursor solution (which can contain nanomaterial additives, in the case of nanocomposites) from a needle to deposit a non-woven nanofiber filter on a collector surface. Using electrospinning, we develop an optimized, macroporous carbon nanotube-carbon nanofiber composite that utilizes the

  19. Fabrication, structure, and magnetic properties of electrospun Ce{sub 0.96}Fe{sub 0.04}O{sub 2} nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Sonsupap, Somchai [School of Physics, Suranaree University of Technology, Nakhon Ratchasima (Thailand); Kidkhunthod, Pinit; Chanlek, Narong [Synchrotron Light Research Institute, Nakhon Ratchasima (Thailand); Pinitsoontorn, Supree [Department of Physics, Faculty of Science, Khon Kaen University, Khon Kaen (Thailand); Maensiri, Santi, E-mail: santimaensiri@g.sut.ac.th [School of Physics, Suranaree University of Technology, Nakhon Ratchasima (Thailand); NANOTEC-SUT Center of Excellence on Advanced Functional Nanomaterials, Suranaree University of Technology, Nakhon Ratchasima (Thailand)

    2016-09-01

    Highlights: • Intrinsic ferromagnetism in electrospun nanofibers of Ce{sub 0.96}Fe{sub 0.04}O{sub 2} is reported. • The prepared samples were well characterized by XRD, TEM, XANES, XPS, and VSM. • Ce{sub 0.96}Fe{sub 0.04}O{sub 2} samples are ferromagnetic having Ms of 0.002–0.923 emu/g at 10 kOe. • Oxygen vacancies play an important role to induce room temperature ferromagnetism. • Ferromagnetism observed in Ce{sub 0.96}Fe{sub 0.04}O{sub 2} is intrinsic. - Abstract: We report room temperature ferromagnetism in ∼30–60 nm nanofibers of Ce{sub 0.96}Fe{sub 0.04}O{sub 2} calcined at 500, 600, 700, and 800 °C. The as-spun nanofibers were fabricated by electrospinning technique. Nanofibers of the as-spun and calcined samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), and vibrating sample magnetometer (VSM). The XRD and TEM with selected electron diffraction (SEAD) analysis results indicate that the Ce{sub 0.96}Fe{sub 0.04}O{sub 2} nanofibers have a cubic perovskite structure without any secondary phase. The as-spun samples exhibit a diamagnetic behavior, whereas the calcined Ce{sub 0.96}Fe{sub 0.04}O{sub 2} samples are ferromagnetic having the specific magnetizations of 0.002–0.923 emu/g at 10 kOe. The results from XAS spectra show the valence state of Fe{sup 3+} and Fe{sup 2+} mixed in the Ce{sub 0.96}Fe{sub 0.04}O{sub 2} samples indicating oxygen vacancies in the nanofibers. Similarly, the results XPS spectra show that there are oxygen vacancies in the nanofibers as a result of Ce{sup 3+} on the surface. These oxygen vacancies play an important role to induce room temperature ferromagnetism (RT-FM) in the calcined Ce{sub 0.96}Fe{sub 0.04}O{sub 2} nanofibers. Our results indicate that the ferromagnetic properties of Ce{sub 0.96}Fe{sub 0.04}O{sub 2} system are intrinsic and are not a result of

  20. Significant improvement of biocompatibility of polypropylene mesh for incisional hernia repair by using poly-epsilon-caprolactone nanofibers functionalized with thrombocyte-rich solution

    Czech Academy of Sciences Publication Activity Database

    Plencner, Martin; Prosecká, Eva; Rampichová, Michala; East, B.; Buzgo, Matej; Vysloužilová, L.; Hoch, J.; Amler, Evžen

    2015-01-01

    Roč. 10, č. 2015 (2015), s. 2635-2646 E-ISSN 1178-2013 Institutional support: RVO:68378041 Keywords : nanofibers * growth factors * polypropylene mesh * hernia regeneration * in vitro Subject RIV: FP - Other Medical Disciplines Impact factor: 4.320, year: 2015

  1. Magnetic electrospun short nanofibers wrapped graphene oxide as a promising biomaterials for guiding cellular behavior.

    Science.gov (United States)

    Feng, Zhang-Qi; Shi, Chuanmei; Zhao, Bin; Wang, Ting

    2017-12-01

    Magnetic particles show extremely wide application prospects in the biomedical field, particularly in the success of cellular manipulation, drug delivery systems, magnetic hyperthermia and NRI contrast enhancement. Graphene oxide with functional groups has a promising biological effect. In this work, we develop magnetic short-fibers wrapped graphene oxide for guiding cellular behavior with the aid of high-speed shear of nanofibers fabricated through electrospinning technique. The diameter and the length of short-fibers are about 300nm and 80μm, respectively. The short-fibers exhibit superior magnetic properties (saturation magnetization value: 50.33emu/g), which has a strong response appearance to the NdFeB magnet. SEM images and laser confocal images display that there has an extremely tight adhesion between the short-fibers wrapped graphene oxide and cells. The control of cell-fibers structure behavior can be realized by applying external magnet. The results may provide an attractive perspective on the treatment of disease with magnetic field. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Surface-Functionalized Electrospun Titania Nanofibers for the Scavenging and Recycling of Precious Metal Ions.

    Science.gov (United States)

    Dai, Yunqian; Formo, Eric; Li, Haoxuan; Xue, Jiajia; Xia, Younan

    2016-10-20

    Precious metals are widely used as catalysts in industry. It is of critical importance to keep the precious metal ions leached from catalysts at a level below one part per million (ppm) in the final products and to recycle the expensive precious metals. Here we demonstrate a simple and effective method for scavenging precious metal ions from an aqueous solution and thereby reduce their concentrations down to the parts per billion (ppb) level. The key component is a filtration membrane comprised of titania (TiO 2 ) nanofibers whose surface has been functionalized with a silane bearing amino or thiol group. When operated under continuous flow at a rate of 1 mL min -1 and at room temperature, up to 99.95 % of the Pd 2+ ions could be removed from a stock solution with an initial concentration of 100 ppm. This work offers a viable strategy not only for the removal of precious metal ions but also for recovering and further recycling them for use as catalysts. For example, the captured Pd 2+ ions could be converted to nanoparticles and used as catalysts for organic reactions such as Suzuki coupling in a continuous flow reactor. This system can be potentially applied to pharmaceutical industry and waste stream treatment. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Improved sensitivity of wearable nanogenerators made of electrospun Eu3+ doped P(VDF-HFP)/graphene composite nanofibers for self-powered voice recognition

    Science.gov (United States)

    Adhikary, Prakriti; Biswas, Anirban; Mandal, Dipankar

    2016-12-01

    Composite nanofibers of Eu3+ doped poly(vinylidene fluoride-co-hexafluoropropylene) (P(VDF-HFP))/graphene are prepared by the electrospinning technique for the fabrication of ultrasensitive wearable piezoelectric nanogenerators (WPNGs) where the post-poling technique is not necessary. It is found that the complete conversion of the piezoelectric β-phase and the improvement of the degree of crystallinity is governed by the incorporation of Eu3+ and graphene sheets into P(VDF-HFP) nanofibers. The flexible nanocomposite fibers are associated with a hypersensitive electronic transition that results in an intense red light emission, and WPNGs also have the capability of detecting external pressure as low as ~23 Pa with a higher degree of acoustic sensitivity, ~11 V Pa-1, than has ever been previously reported. This means that ultrasensitive WPNGs can be utilized to recognize human voices, which suggests they could be a potential tool in the biomedical and national security sectors. The capacitor’s ability to charge from abundant environmental vibrations, such as music, wind, body motion, etc, drives WPNGs as a power source for portable electronics. This fact may open up the prospect of using the Eu3+ doped P(VDF-HFP)/graphene composite electrospun nanofibers, with their multifunctional properties such as vibration sensitivity, wearability, red light emission capability and piezoelectric energy harvesting, for various promising applications in portable electronics, health care monitoring, noise detection and security monitoring.

  4. Evaluation of the factors influencing the resultant diameter of the electrospun gelatin/sodium alginate nanofibers via Box-Behnken design.

    Science.gov (United States)

    Gönen, Seza Özge; Erol Taygun, Melek; Küçükbayrak, Sadriye

    2016-01-01

    This article presented a study on the effects of solution properties (i.e., gelatin concentration, alginate concentration, content of alginate solution in the blend solution, and content of acetic acid in the solvent of gelatin solution) on the average diameter of electrospun gelatin/sodium alginate nanofibers, as well as its standard deviation. For this purpose, blend solutions of two natural polymers (gelatin and sodium alginate) were prepared both in the absence and presence of ethanol. Response surface methodology based on a three-level, four-variable Box-Benkhen design was employed to define quadratic relationships between the responses and the solution properties. The individual and interactive effects of the solution properties were determined. Moreover, the adequacy of the models was verified by the validation experiments. Results showed that the average diameters of the resultant nanofibers were 68-166 nm and 90-155 nm in the absence and presence of ethanol, respectively. The experimental results were in good agreement with the predicted response values. Hence, this study provides an overview on the fabrication of gelatin/sodium alginate nanofibers with targeted diameter, which may have potential to be used in the field of tissue engineering. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Influence of the collector and heat treatment in the structure of BiFeO{sub 3} electrospun nanofibers; Influencia do coletor e do tratamento termico na estrutura de nanofibras eletrofiadas de BiFeO3

    Energy Technology Data Exchange (ETDEWEB)

    Melo, G.H.F.; Santos, J.P.F.; Bretas, R.E.S., E-mail: bretas@ufscar.br [Universidade Federal de Sao Carlos (DEMa/UFSCar). SP (Brazil). Departamento de Engenharia de Materiais

    2016-07-01

    The objective of this work was to analyze the influence of the collector type and heat treatment on the morphology and crystalline phases of BiFeO{sub 3} electrospun nanofibers. A solution containing (Fe(NO{sub 3}){sub 3.9}H{sub 2}O and Bi(NO{sub 3}){sub 3.5}H{sub 2}O) as precursors together with a polyvinylpyrrolidone solution was electrospun using 2.8KV/cm as electrical field. The collector type was however, changed (aluminum and glass). After the electrospinning, the as-spun nanofibers were submitted to two different heat treatments: one at 550°C and the other at 750°C, both during 2h. The collector type changed the morphology of the nanofibers; while in the glass collector, a non-woven mat of flat and rough nanofibers was obtained, in the aluminum collector, mats of circular and smooth nanofibers were obtained. The thermal treatment also changed the morphology and amount of crystalline phases; at 550°C, the nanofiber morphology was maintained and only one crystalline phase (BiFeO{sub 3}) was detected. On the other hand, at 750°C, flakes were obtained of two crystalline phases (BiFeO{sub 3} and Bi{sub 2}Fe{sub 4}O{sub 9}). (author)

  6. Cryogenic grinding of electrospun poly-epsilon-caprolactone mesh submerged in liquid media

    Czech Academy of Sciences Publication Activity Database

    Knotek, P.; Pouzar, M.; Buzgo, Matej; Křížková, B.; Vlček, Milan; Míčková, Andrea; Plencner, Martin; Návesník, J.; Amler, Evžen; Bělina, P.

    2012-01-01

    Roč. 32, č. 6 (2012), s. 1366-1374 ISSN 0928-4931 Grant - others:GA MŠk(CZ) GA UK 330611; GA MŠk(CZ) GA UK 384311; GA MŠk(CZ) GA UK 99610; GA MŠk(CZ) ME 10145; GA MŠk(CZ) MSM0021627501; GA MŠk(CZ) ERA-NET Carsila ME10145; EU FP7(XE) BIOSCENT ID 214539 Institutional research plan: CEZ:AV0Z50390703; CEZ:AV0Z40500505 Keywords : cryogenic grinding * poly-epsilon-caprolactone * nano/micro-mesh Subject RIV: BO - Biophysics Impact factor: 2.404, year: 2012

  7. Preparation of graphene oxide/poly (3,4-ethylenedioxytriophene): Poly (styrene sulfonate) (PEDOT:PSS) electrospun nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Efelina, Vita; Widianto, Eri [Department of Physics, Universitas Gadjah Mada, Sekip Utara BLS.21 Yogyakarta, 55281 Indonesia (Indonesia); Rusdiana, Dadi [Department of Physical Education, Universitas Pendidikan Indonesia, Bandung (Indonesia); Nugroho, A. A. [Department of Physics, Institut Teknologi Bandung, Jl. Ganesha 10 Bandung (Indonesia); Kusumaatmaja, Ahmad; Triyana, Kuwat; Santoso, Iman, E-mail: iman.santoso@ugm.ac.id [Department of Physics, Universitas Gadjah Mada, Sekip Utara BLS.21 Yogyakarta, 55281 Indonesia (Indonesia); Nanomaterials Research Group, Universitas Gadjah Mada,, Sekip Utara, Yogyakarta (Indonesia)

    2016-04-19

    Graphene oxide (GO)/Poly (3,4-Ethylenedioxytriophene):Poly (styrene Sulfonate) (PEDOT:PSS) nanofibers have been successfully fabricated by a simple electrospinning technique to develop conductive nanofibers with polyvinyl alcohol (PVA) act as a carrier solution. Graphene oxide has been synthesized by Hummer’s method and has been confirmed by Raman Spectroscopy, FTIR and UV-Vis Spectroscopy. GO/PEDOT:PSS composite nanofibers. The structural and morphological properties were characterized by Scanning Electron Microscopy (SEM). The result of SEM show that GO/PEDOT:PSS nanofibers has a relatively uniform morphology nanofiber with diameter between 180 nm - 340 nm with smooth nanofiber surface. The produced nanofibers from this study can be utilized for various applications such as flexible, conductive and transparent electrode.

  8. Electrospun Fe3O4/TiO2 hybrid nanofibers and their in vitro biocompatibility: Prospective matrix for satellite cell adhesion and cultivation

    International Nuclear Information System (INIS)

    Amna, Touseef; Hassan, M. Shamshi; Van Ba, Hoa; Khil, Myung-Seob; Lee, Hak-Kyo; Hwang, I.H.

    2013-01-01

    We report the fabrication of novel Fe 3 O 4 /TiO 2 hybrid nanofibers with the improved cellular response for potential tissue engineering applications. In this study, Fe 3 O 4 /TiO 2 hybrid nanofibers were prepared by facile sol–gel electrospinning using titanium isopropoxide and iron(III) nitrate nonahydrate as precursors. The obtained electrospun nanofibers were vacuum dried at 80 °C and then calcined at 500 °C. The physicochemical characterization of the synthesized composite nanofibers was carried out by scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy and X-ray diffraction pattern. To examine the in vitro cytotoxicity, satellite cells were treated with as-prepared Fe 3 O 4 /TiO 2 and the viability of cells was analyzed by Cell Counting Kit-8 assay at regular time intervals. The morphological features of unexposed satellite cells and exposed to Fe 3 O 4 /TiO 2 composite were examined with a phase contrast microscope whereas the quantification of cell viability was carried out via confocal laser scanning microscopy. The morphology of the cells attached to hybrid matrix was observed by Bio-SEM. Cytotoxicity experiments indicated that the satellite cells could attach to the Fe 3 O 4 /TiO 2 composite nanofibers after being cultured. We observed that Fe 3 O 4 –TiO 2 composite nanofibers could support cell adhesion and growth. Results from this study therefore suggest that Fe 3 O 4 /TiO 2 composite scaffold with small diameters (approximately 200 nm) can mimic the natural extracellular matrix well and provide possibilities for diverse applications in the field of tissue engineering and regenerative medicine. Highlights: ► We report fabrication of novel Fe 3 O 4 /TiO 2 hybrid nanofibers by facile electrospinning. ► The utilized satellite cells were isolated from native Korean Hanwoo cattle. ► Fe 3 O 4 /TiO 2 composite with small diameters (∼ 200 nm) can mimic the natural ECM well. ► Fe 3 O 4 /TiO 2

  9. Preparation of graphene oxide/poly (3,4-ethylenedioxytriophene): Poly (styrene sulfonate) (PEDOT:PSS) electrospun nanofibers

    Science.gov (United States)

    Widianto, Eri; Efelina, Vita; Rusdiana, Dadi; Nugroho, A. A.; Kusumaatmaja, Ahmad; Triyana, Kuwat; Santoso, Iman

    2016-04-01

    Graphene oxide (GO)/Poly (3,4-Ethylenedioxytriophene):Poly (styrene Sulfonate) (PEDOT:PSS)nanofibers have been successfully fabricated by a simple electrospinning technique to develop conductive nanofibers with polyvinyl alcohol (PVA) act as a carrier solution. Graphene oxide hasbeen synthesized by Hummer's method and has been confirmed by Raman Spectroscopy, FTIR, and UV-Vis Spectroscopy. The structural and morphological properties of GO/PEDOT:PSS composite nanofiberswere characterized by Scanning Electron Microscopy (SEM). The result of SEM showed that GO/PEDOT:PSS nanofibers have a relatively uniform morphology nanofiber with adiameterof 180 nm - 340 nm with smooth nanofiber surface. The produced nanofibers from this study can be utilized for various applicationssuch as aflexible, conductive and transparent electrode.

  10. Anti-Neoplastic Cytotoxicity of SN-38-Loaded PCL/Gelatin Electrospun Composite Nanofiber Scaffolds against Human Glioblastoma Cells In Vitro.

    Science.gov (United States)

    Zhu, Xiaodong; Ni, Shilei; Xia, Tongliang; Yao, Qingyu; Li, Haoyuan; Wang, Benlin; Wang, Jiangang; Li, Xingang; Su, Wandong

    2015-12-01

    Electrospun poly(ε-caprolactone) (PCL)/gelatin (GT) scaffolds were developed to provide controlled release of 7-ethyl-10-hydroxy camptothecin (SN-38). Acetic acid was introduced to improve the miscibility of PCL and GT to produce a homogeneous nanofiber membrane mixture. The effect of SN-38 content in binary mixtures on processability, fiber morphology, water sorption, swelling, and drug release was investigated. Electrospun PCL/GT blend nonwoven fibers showed fiber surface roughness, decreased PCL crystallinity, and increased swelling with increasing drug content of 1, 2, and 4 wt %. Additionally, increasing the SN-38 concentration reduced the degradation rate of the GT. Furthermore, we hypothesize the existence of a drug content saturation point in the monoaxial fiber to explain the different drug release patterns of PG2 compared with those of PG1 and PG4. The matrix also showed good biodegradation and anti-tumor function. Our results demonstrate that SN-38-loaded PCL/GT fibers can be obtained by electrospinning. The SN-38-loaded fibers merit further evaluation as a means to potentially prevent locoregional recurrence following surgical tumor resection. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  11. Hierarchical heterostructures of p-type bismuth oxychloride nanosheets on n-type zinc ferrite electrospun nanofibers with enhanced visible-light photocatalytic activities and magnetic separation properties.

    Science.gov (United States)

    Sun, Yucong; Shao, Changlu; Li, Xinghua; Guo, Xiaohui; Zhou, Xuejiao; Li, Xiaowei; Liu, Yichun

    2018-04-15

    P-type bismuth oxychloride (p-BiOCl) nanosheets were uniformly grown on n-type zinc ferrite (n-ZnFe 2 O 4 ) electrospun nanofibers via a solvothermal technique to form hierarchical heterostructures of p-BiOCl/n-ZnFe 2 O 4 (p-BiOCl/n-ZnFe 2 O 4 H-Hs). The density and loading amounts of the BiOCl nanosheets with exposed {0 0 1} facets were easily controlled by adjusting the reactant concentration in the solvothermal process. The p-BiOCl/n-ZnFe 2 O 4 H-Hs exhibited enhanced visible-light photocatalytic activities for the degradation of Rhodamine B (RhB). The apparent first-order rate of the p-BiOCl/n-ZnFe 2 O 4 H-Hs and its normalized constant were about 12.6- and 8-fold higher than pure ZnFe 2 O 4 nanofibers. This suggests that both the improved charge separation efficiency from the uniform p-n heterojunctions and the enlarged active surface sites from the hierarchical structures increase the photocatalytic performances. Furthermore, the p-BiOCl/n-ZnFe 2 O 4 H-Hs could be efficiently separated from the solution with an external magnetic field via the ferromagnetic behavior of ZnFe 2 O 4 nanofibers. The magnetic p-BiOCl/n-ZnFe 2 O 4 H-Hs with enhanced visible-light photocatalytic performances might have potential applications in water treatment. Copyright © 2018. Published by Elsevier Inc.

  12. Enhanced Bioavailability and Anticancer Effect of Curcumin-Loaded Electrospun Nanofiber: In Vitro and In Vivo Study

    Science.gov (United States)

    Wang, Chuan; Ma, Chao; Wu, Zhenkai; Liang, He; Yan, Peng; Song, Jia; Ma, Nan; Zhao, Qinghua

    2015-11-01

    Nanofibers have attracted increasing attention in drug delivery and other biomedical applications due to their some special properties. The present study aims to prepare a fiber-based nanosolid dispersion system to enhance the bioavailability of curcumin (CUR). CUR-loaded polyvinyl pyrrolidone (CUR@PVP) nanofibers were successfully prepared via electrospinning. Scanning electron microscopy (SEM) was employed to observe the morphology of the nanofibers, and the SEM image showed that the drug-loaded nanofibers were smooth, and no CUR clusters were found on the surface of the nanofibers. The results of X-ray diffraction (XRD) demonstrated that the CUR was evenly distributed in the nanofibers in an amorphous state. Fourier transform infrared (FTIR) spectroscopy analysis indicated that intermolecular hydrogen bonding occurred between the CUR and the polymer matrix. In vitro dissolution profiles showed that CUR@PVP nanofiber could be quickly dissolved in phosphate-buffered saline (PBS) solution, while negligible dissolution was observed in pure CUR sample. Importantly, in vitro cell viability assays and in vivo animal tests revealed that the nanosolid dispersion system dramatically enhanced the bioavailability and showed effective anticancer effect of the CUR.

  13. Modification of electrospun polyacrylonitrile nanofibers with EDTA for the removal of Cd and Cr ions from water effluents

    Energy Technology Data Exchange (ETDEWEB)

    Chaúque, Eutilério F.C., E-mail: efchauque@gmail.com [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Dlamini, Langelihle N., E-mail: lndlamini@uj.ac.za [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Adelodun, Adedeji A., E-mail: aadelodun@uj.ac.za [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa); Greyling, Corinne J., E-mail: GreylingC@cput.ac.za [Technology Station in Clothing and Textiles, Cape Peninsula University of Technology, Symphony Way, Bellville, 7535 (South Africa); Catherine Ngila, J., E-mail: jcngila2002@yahoo.com [Department of Applied Chemistry, University of Johannesburg, Doornfontein 2028, Johannesburg (South Africa)

    2016-04-30

    Graphical abstract: - Highlights: • Polyscrylonitrile (PAN) nanofibers prepared through electrospinning and chemically modified with ethylenediaminetetraacetic acid using ethylenediamine crosslinker. • Fabricated nanofibers have enhanced surface chemistry with insignificant impact on the nanofibrous structure. • Excellent maximum adsorption capacities of 66.24 and 32.68 mg g{sup −1} toward Cr and Cd ions, respectively. • A pre-concentration factor of 19 achieved for removal of Cd and Cr in environmental water samples. - Abstract: Polyacrylonitrile (PAN) nanofibers were obtained by electrospinning technique prior to surface modification with polyethylenediaminetetraacetic acid (EDTA) using ethylenediamine (EDA) as the cross-linker. The modified nanofibers (EDTA-EDA-PAN) were subsequently applied in the wastewater treatment for the removal of Cd(II) and Cr(VI). Textural and chemical characterizations of the nanofibers were carried out by analysis of the specific surface area (Brauner Emmet and Teller (BET)) and thermogravimetric analyses, scanning electron microscopy and Fourier transform infrared spectroscopy. From the adsorption equilibrium studies with Langmuir, Freundlich and Temkin isotherm models, Freundlich was found most suitable for describing the removal mechanism of the target metals as they collect on a heterogeneously functionalized polymer surface. The EDTA-EDA-PAN nanofibers showed effective sorption affinity for both Cd(II) and Cr(VI), achieving maximum adsorption capacities of 32.68 and 66.24 mg g{sup -1}, respectively, at 298 K. In furtherance, the nanofibers were regenerated by simple washing with 2 M HCl solution. Conclusively, the EDTA-EDA-PAN nanofibers were found to be efficient for the removal of Cd(II) and Cr(VI) in water effluents.

  14. Non-woven and aligned electrospun multicomponent luminescent polymer nanofibers: effects of aggregated morphology on the photophysical properties

    International Nuclear Information System (INIS)

    Wang, Cheng-Ting; Kuo, Chi-Ching; Chen, Hsieh-Chih; Chen, Wen-Chang

    2009-01-01

    In this paper, the morphology and photophysical properties of non-woven and aligned ES nanofibers prepared from the ternary blends of poly(9,9-dioctylfluorenyl-2,7-diyl) (PFO) / poly(2,3-dibutoxy-1,4-phenylene vinylene) (DB-PPV) / poly(methyl methacrylate) (PMMA) using a single-capillary spinneret are reported. Various PFO and DB-PPV phase-separated structures in the ES nanofibers were found by two different solvents: ellipsoidal DB-PPV (10-40 nm) and fiber-like PFO (20-40 nm) in the PMMA using chloroform, while fiber-like DB-PPV (10-20 nm) and fiber-like PFO (20-30 nm) using chlorobenzene. Such different PFO and DB-PPV structures resulted in various energy transfer/emission colors in the ES nanofibers. Moreover, highly aligned luminescence PFO/DB-PPV/PMMA blend ES nanofibers prepared from chlorobenzene showed a much higher polarized emission than the non-woven and the emission colors changed from blue to greenish-blue to green as the DB-PPV composition increased. The different polarized emission characteristics between PFO and DB-PPV in the ES nanofibers also led to varied emission colors at different angles. The present study suggests the morphologies and emission characteristics of the multicomponent ES nanofibers could be efficiently tuned through solvent types and blend ratios of semiconducting polymers.

  15. Non-woven and aligned electrospun multicomponent luminescent polymer nanofibers: effects of aggregated morphology on the photophysical properties.

    Science.gov (United States)

    Wang, Cheng-Ting; Kuo, Chi-Ching; Chen, Hsieh-Chih; Chen, Wen-Chang

    2009-09-16

    In this paper, the morphology and photophysical properties of non-woven and aligned ES nanofibers prepared from the ternary blends of poly(9,9-dioctylfluorenyl-2,7-diyl) (PFO) / poly(2,3-dibutoxy-1,4-phenylene vinylene) (DB-PPV) / poly(methyl methacrylate) (PMMA) using a single-capillary spinneret are reported. Various PFO and DB-PPV phase-separated structures in the ES nanofibers were found by two different solvents: ellipsoidal DB-PPV (10-40 nm) and fiber-like PFO (20-40 nm) in the PMMA using chloroform, while fiber-like DB-PPV (10-20 nm) and fiber-like PFO (20-30 nm) using chlorobenzene. Such different PFO and DB-PPV structures resulted in various energy transfer/emission colors in the ES nanofibers. Moreover, highly aligned luminescence PFO/DB-PPV/PMMA blend ES nanofibers prepared from chlorobenzene showed a much higher polarized emission than the non-woven and the emission colors changed from blue to greenish-blue to green as the DB-PPV composition increased. The different polarized emission characteristics between PFO and DB-PPV in the ES nanofibers also led to varied emission colors at different angles. The present study suggests the morphologies and emission characteristics of the multicomponent ES nanofibers could be efficiently tuned through solvent types and blend ratios of semiconducting polymers.

  16. Nano silver-embedded electrospun nanofiber of poly(4-chloro-3-methylphenyl methacrylate): use as water sanitizer.

    Science.gov (United States)

    Shekh, Mehdihasan I; Patel, Nirmal N; Patel, Kaushal P; Patel, Rajnikant M; Ray, Arabinda

    2017-02-01

    Water contaminated with microorganisms causes numerous diseases and is a major concern for public health. In search of a simple material which can provide clean water free from pathogens, nanofibers of poly(4-chloro-3-methylphenyl methacrylate, abbreviated as CMPMA, and nano Ag-doped poly(CMPMA) composite nanofibers were used to decontaminate water from microorganisms such as Escherichia coli and Bacillus subtilis. Nanofibers were prepared by electrospinning. X-ray diffraction (XRD) and transmission electron microscopy (TEM) provide the diameters of the Ag nanoparticles which are in the range 18-21 and 13-18 nm. The diameter of the poly(CMPMA) and nano Ag-doped poly(CMPMA) composite nanofiber is seen to vary between 400 and 700 nm with the change of the processing parameters. Optimum parameters for uniform nanofibers have been obtained. The morphology of the fibers is derived from scanning electron microscopy (SEM). The superiority of the nano Ag-doped poly(CMPMA) composite nanofiber was established.

  17. Electrospun composite nanofiber membrane of poly(l-lactide) and surface grafted chitin whiskers: Fabrication, mechanical properties and cytocompatibility.

    Science.gov (United States)

    Liu, Hua; Liu, Wenjun; Luo, Binghong; Wen, Wei; Liu, Mingxian; Wang, Xiaoying; Zhou, Changren

    2016-08-20

    To improve both the mechanical properties and cytocompatibility of poly(l-lactide) (PLLA), rod-like chitin whiskers (CHWs) were prepared, and subsequently surface modified with l-lactide to obtain grafted CHWs (g-CHWs). Then, CHWs and g-CHWs were further introduced into PLLA matrix to fabricate CHWs/PLLA and g-CHWs/PLLA nanofiber membranes by electrospinning technique. Morphologies and properties of the CHWs and g-CHWs were characterized. The surface-grafted PLLA chains played an important role in improving interfacial interaction between the whiskers and PLLA matrix. The g-CHWs dispersed more uniformly in matrix than CHWs, and the as-prepared g-CHWs/PLLA nanofiber membrane showed relative smooth and uniform fiber. As a result, the tensile strength and modulus of the g-CHWs/PLLA nanofiber membrane were obviously superior to those of the pure PLLA and CHWs/PLLA nanofiber membranes. Cells culture results indicated that g-CHWs/PLLA nanofiber membrane is more effectively in promoting MC3T3-E1 cells adhesion, spreading and proliferation than pure PLLA and CHWs/PLLA nanofiber membrane. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Efficient adsorption and antibacterial properties of electrospun CuO-ZnO composite nanofibers for water remediation

    Energy Technology Data Exchange (ETDEWEB)

    Malwal, Deepika [Nanobiotechnology Laboratory, Centre for Nanotechnology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India); Gopinath, P., E-mail: pgopifnt@iitr.ernet.in [Nanobiotechnology Laboratory, Centre for Nanotechnology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India); Department of Biotechnology, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667 (India)

    2017-01-05

    Highlights: • Synthesis of CuO-ZnO composite nanofibers using simple electrospinning technique. • Characterization data confirmed the proper structure. • Exploited as effective adsorbent for congo red dye. • Several adsorption kinetic and isotherm models were discussed. • Evaluation of antibacterial activity against GFP-E.coli and S. aureus. - Abstract: On the face of impending global water resources, developing low-cost and efficient water treatment technologies and materials thereof is highly important. Herein, we explore the adsorption capacity and antibacterial properties of CuO-ZnO (CZ) composite nanofibers. The ultrafine nanofibers were fabricated using simple and inexpensive electrospinning technique and were further characterized using Field Emission-Scanning Electron Microscope (FE-SEM), Transmission electron microscope (TEM) and X-Ray Diffraction (XRD), Thermogravimetric analysis (TGA), Fourier transform Infrared Spectroscopy (FTIR). When employed as nanoadsorbents, CZ nanofibers exhibited excellent adsorption capacity for congo red dye. Adsorption Isotherms and kinetics were performed to determine the maximum adsorption capacity and the rate of adsorption, respectively, depicting the better efficiency of composite nanofibers as compared to their single counterparts. The mechanism of adsorption is also proposed with the evaluation of diffusion studies. The second part of this study deals with the examination of antibacterial activity of CZ composite nanofibers against antibiotic resistant GFP-E.coli and S. aureus. The antibacterial efficacy was monitored by visual turbidity assay, SEM analysis and reactive oxygen species (ROS) determination. Hence, such nanofibers have been explored as a single platform for the removal of biological as well organic contaminants so as to make them potential in the field of water remediation.

  19. Observation of triple helix motif on electrospun collagen nanofibers and its effect on the physical and structural properties

    Science.gov (United States)

    Bürck, Jochen; Aras, Onur; Bertinetti, Luca; Ilhan, Caner A.; Ermeydan, Mahmut A.; Schneider, Reinhard; Ulrich, Anne S.; Kazanci, Murat

    2018-01-01

    Collagen is a very popular natural biomaterial due to its high biocompatibility and bioactivity. Electrospinning is currently the only technique that allows the fabrication of continuous fibers with diameters down to a few nanometers. In order to regenerate collagen in the forms of nanofibers, it is necessary to dissolve it in suitable solvents. The solvents and electrospinning process cause unfolding of collagen nanofibers. It is proposed that acidic solvents preserve better the natural structure of collagen fibers. In this paper, the structures of collagen nanofibers were examined by using circular dichroism (CD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, differential scanning calorimetry (DSC) and sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) methods in order to test this hypothesis. The increase in PP-II fraction, representing the triple helix structure in collagen, that was observed in CD analysis of HAc derived collagen nanofibers, for the first time was successfully confirmed and illustrated by using SEM and TEM methods. Furthermore, CD revealed the mostly detrimental effect of stabilization conditions such as heat, vacuum and UV treatment on the secondary structure of the collagen nanofibers.

  20. Amorphous SiO2 NP-Incorporated Poly(vinylidene fluoride) Electrospun Nanofiber Membrane for High Flux Forward Osmosis Desalination.

    Science.gov (United States)

    Obaid, M; Ghouri, Zafar Khan; Fadali, Olfat A; Khalil, Khalil Abdelrazek; Almajid, Abdulhakim A; Barakat, Nasser A M

    2016-02-01

    Novel amorphous silica nanoparticle-incorporated poly(vinylidine fluoride) electrospun nanofiber mats are introduced as effective membranes for forward osmosis desalination technology. The influence of the inorganic nanoparticle content on water flux and salt rejection was investigated by preparing electrospun membranes with 0, 0.5, 1, 2, and 5 wt % SiO2 nanoparticles. A laboratory-scale forward osmosis cell was utilized to validate the performance of the introduced membranes using fresh water as a feed and different brines as draw solution (0.5, 1, 1.5, and 2 M NaCl). The results indicated that the membrane embedding 0.5 wt % displays constant salt rejection of 99.7% and water flux of 83 L m(-2) h(-1) with 2 M NaCl draw solution. Moreover, this formulation displayed the lowest structural parameter (S = 29.7 μm), which represents approximately 69% reduction compared to the pristine membrane. Moreover, this study emphasizes the capability of the electrospinning process in synthesizing effective membranes as the observed water flux and average salt rejection of the pristine poly(vinylidine fluoride) membrane was 32 L m(-2) h(-1) (at 2 M NaCl draw solution) and 99%, respectively. On the other hand, increasing the inorganic nanoparticles to 5 wt % showed negative influence on the salt rejection as the observed salt flux was 1651 mol m(-2) h(-1). Besides the aforementioned distinct performance, studies of the mechanical properties, porosity, and wettability concluded that the introduced membranes are effective for forward osmosis desalination technology.

  1. Surface-assisted laser desorption/ionization time-of-flight mass spectrometry of small drug molecules and high molecular weight synthetic/biological polymers using electrospun composite nanofibers.

    Science.gov (United States)

    Bian, Juan; Olesik, Susan V

    2017-03-27

    Polyacrylonitrile/Nafion®/carbon nanotube (PAN/Nafion®/CNT) composite nanofibers were prepared using electrospinning. These electrospun nanofibers were studied as possible substrates for surface-assisted laser desorption/ionization (SALDI) and matrix-enhanced surface-assisted laser desorption/ionization time-of-flight mass spectrometry (ME-SALDI/TOF-MS) for the first time in this paper. Electrospinning provides this novel substrate with a uniform morphology and a narrow size distribution, where CNTs were evenly and firmly immobilized on polymeric nanofibers. The results show that PAN/Nafion®/CNT nanofibrous mats are good substrates for the analysis of both small drug molecules and high molecular weight polymers with high sensitivity. Markedly improved reproducibility was observed relative to MALDI. Due to the composite formation between the polymers and the CNTs, no contamination of the carbon nanotubes to the mass spectrometer was observed. Furthermore, electrospun nanofibers used as SALDI substrates greatly extended the duration of ion signals of target analytes compared to the MALDI matrix. The proposed SALDI approach was successfully used to quantify small drug molecules with no interference in the low mass range. The results show that verapamil could be detected with a surface concentration of 220 femtomoles, indicating the high detection sensitivity of this method. Analysis of peptides and proteins with the electrospun composite substrate using matrix assisted-SALDI was improved and a low limit of detection of approximately 6 femtomoles was obtained for IgG. Both SALDI and ME-SALDI analyses displayed high reproducibility with %RSD ≤ 9% for small drug molecules and %RSD ≤ 14% for synthetic polymers and proteins.

  2. Magnetic and optical properties of electrospun hollow nanofibers of SnO2 doped with Ce-ion

    Science.gov (United States)

    Mohanapriya, P.; Pradeepkumar, R.; Victor Jaya, N.; Natarajan, T. S.

    2014-07-01

    Cerium doped SnO2 hollow nanofibers were synthesized by electrospinning. High resolution scanning electron microscope (HRSEM) and transmission electron microscopy (TEM) analysis showed hollow nanofibers with diameters around ˜200 nm. The optimized substitution of Ce ion into SnO2 lattices happened above 6 mol. % doping as confirmed by Powder X-ray diffraction (XRD) studies. Optical band gap was decreased by the doping confirming the direct energy transfer between f-electrons of rare earth ion and the SnO2 conduction or valence band. The compound also exhibited room temperature ferromagnetism with the saturation magnetization of 19 × 10-5 emu/g at 6 mol. %. This study demonstrates the Ce doped SnO2 hollow nanofibers for applications in magneto-optoelectronic devices.

  3. Preparation and optical properties of afterglow Sr_2MgSi_2O_7:Eu"2"+, Dy"3"+ electrospun nanofibers

    International Nuclear Information System (INIS)

    He, Ling; Jia, Baolan; Che, Lianyu; Li, Wensheng; Sun, Weimin

    2016-01-01

    One-dimensional Sr_2MgSi_2O_7:Eu"2"+, Dy"3"+ nanofibers were synthesized by a simple and cost-effective electrospinning technique. The samples were characterized by XRD, FT-IR, TG-DTA, SEM, TEM and PL. The XRD and SEM results show single crystal nanofibers of Sr_2MgSi_2O_7:Eu"2"+, Dy"3"+ with an average diameter of 200 nm were obtained by electrospinning preparation and heat treatment at 1150 °C for 5 h. The single crystal structure of Sr_2MgSi_2O_7:Eu"2"+ nanofiber was discussed. The luminescent properties, long lasting performance and formation mechanism are also investigated.

  4. Electrospun cerium-based TiO2 nanofibers for photocatalytic oxidation of elemental mercury in coal combustion flue gas.

    Science.gov (United States)

    Wang, Lulu; Zhao, Yongchun; Zhang, Junying

    2017-10-01

    Photocatalytic oxidation is an attractive method for Hg-rich flue gas treatment. In the present study, a novel cerium-based TiO 2 nanofibers was prepared and selected as the catalyst to remove mercury in flue gas. Accordingly, physical/chemical properties of those nanofibers were clarified. The effects of some important parameters, such as calcination temperature, cerium dopant content and different illumination conditions on the removal of Hg 0 using the photocatalysis process were investigated. In addition, the removal mechanism of Hg 0 over cerium-based TiO 2 nanofibers focused on UV irradiation was proposed. The results show that catalyst which was calcined at 400 °C exhibited better performance. The addition of 0.3 wt% Ce into TiO 2 led to the highest removal efficiency at 91% under UV irradiation. As-prepared samples showed promising stability for long-term use in the test. However, the photoluminescence intensity of nanofibers incorporating ceria was significantly lower than TiO 2 , which was attributed to better photoelectron-hole separation. Although UV and O 2 are essential factors, the enhancement of Hg 0 removal is more obviously related to the participation of catalyst. The coexistence of Ce 3+ and Ce 4+ , which leads to the efficient oxidation of Hg 0 , was detected on samples. Hg 2+ is the final product in the reaction of Hg 0 removal. As a consequence, the emissions of Hg 0 from flue gas can be significantly suppressed. These indicate that combining photocatalysis technology with cerium-based TiO 2 nanofibers is a promising strategy for reducing Hg 0 efficiently. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Electrospun N-Doped Porous Carbon Nanofibers Incorporated with NiO Nanoparticles as Free-Standing Film Electrodes for High-Performance Supercapacitors and CO2 Capture.

    Science.gov (United States)

    Li, Qi; Guo, Jiangna; Xu, Dan; Guo, Jianqiang; Ou, Xu; Hu, Yin; Qi, Haojun; Yan, Feng

    2018-04-01

    Carbon nanofibers (CNF) with a 1D porous structure offer promising support to encapsulate transition-metal oxides in energy storage/conversion relying on their high specific surface area and pore volume. Here, the preparation of NiO nanoparticle-dispersed electrospun N-doped porous CNF (NiO/PCNF) and as free-standing film electrode for high-performance electrochemical supercapacitors is reported. Polyacrylonitrile and nickel acetylacetone are selected as precursors of CNF and Ni sources, respectively. Dicyandiamide not only improves the specific surface area and pore volume, but also increases the N-doping level of PCNF. Benefiting from the synergistic effect between NiO nanoparticles (NPs) and PCNF, the prepared free-standing NiO/PCNF electrodes show a high specific capacitance of 850 F g -1 at a current density of 1 A g -1 in 6 m KOH aqueous solution, good rate capability, as well as excellent long-term cycling stability. Moreover, NiO NPs dispersed in PCNF and large specific surface area provide many electroactive sites, leading to high CO 2 uptake, and high-efficiency CO 2 electroreduction. The synthesis strategy in this study provides a new insight into the design and fabrication of promising multifunctional materials for high-performance supercapacitors and CO 2 electroreduction. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. One-dimensional hierarchical heterostructures of In{sub 2}S{sub 3} nanosheets on electrospun TiO{sub 2} nanofibers with enhanced visible photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xin; Li, Xinghua; Shao, Changlu, E-mail: clshao@nenu.edu.cn; Li, Jinhuan, E-mail: lijh248@nenu.edu.cn; Zhang, Mingyi; Zhang, Peng; Wang, Kexin; Lu, Na; Liu, Yichun

    2013-09-15

    Graphical abstract: One-dimensional In{sub 2}S{sub 3}/TiO{sub 2} hierarchical heterostructures were fabricated based on TiO{sub 2} nanofibers by combining the electrospinning technique (for TiO{sub 2} nanofibers) with the hydrothermal method (for In{sub 2}S{sub 3} nanosheets), which exhibited a high visible light photocatalytic activity for degradation of Methyl orange and reduction of Cr(VI) under visible light illumination (λ > 420 nm). -- Highlights: • Synthesis of one-dimensional In{sub 2}S{sub 3}/TiO{sub 2} hierarchical heterostructures. • Enhanced visible-light photocatalytic activity. • The mechanisms of photodegradation of MO and photoreduction of Cr(VI). -- Abstract: In{sub 2}S{sub 3} nanosheets were assembled on electrospun TiO{sub 2} nanofibers template by a hydrothermal technique. For the obtained one-dimensional In{sub 2}S{sub 3}/TiO{sub 2} hierarchical heterostructures (1D In{sub 2}S{sub 3}/TiO{sub 2} H-HSs), the density and size of the secondary In{sub 2}S{sub 3} nanosheets could be controlled by adjusting the reactant concentrations for the preparation of In{sub 2}S{sub 3} in the hydrothermal process. The 1D In{sub 2}S{sub 3}/TiO{sub 2} H-HSs exhibited higher visible-light photocatalytic activity for the degradation of Methyl orange (MO) and the reduction of Cr(VI), as compared with the pure TiO{sub 2} nanofibers and pure In{sub 2}S{sub 3} nanosheets. The enhanced visible light photocatalytic activity might be attributed to the extended absorption in the visible light region from the narrow band-gap In{sub 2}S{sub 3}, the effective photogenerated electron–hole separation by the photosynergistic effects of the In{sub 2}S{sub 3}/TiO{sub 2} H-HSs and quick electron-transfer in the 1D TiO{sub 2} nanofibers. Meanwhile, the 1D In{sub 2}S{sub 3}/TiO{sub 2} H-HSs could be recycled easily by sedimentation due to their nanofibrous nonwoven web structure. Moreover, the mechanisms of photodegradation of MO and photoreduction of Cr(VI) were proposed

  7. Fundamental Study of Facile and Stable Hydrogen Evolution Reaction at Electrospun Ir and Ru Mixed Oxide Nanofibers.

    Science.gov (United States)

    Cho, Yun-Bin; Yu, Areum; Lee, Chongmok; Kim, Myung Hwa; Lee, Youngmi

    2018-01-10

    Electrochemical hydrogen evolution reaction (HER) has been an interesting research topic in terms of the increasing need of renewable and alternative energy conversion devices. In this article, Ir x Ru 1-x O y (y = 0 or 2) nanofibers with diverse compositions of Ir/IrO 2 and RuO 2 are synthesized by electrospinning and calcination procedures. Their HER activities are measured in 1.0 M NaOH. Interestingly, the HER activities of Ir x Ru 1-x O y nanofibers improve gradually during repetitive cathodic potential scans for HER, and then eventually reach the steady-state consistencies. This cathodic activation is attributed to the transformation of the nanofiber surface oxides to the metallic alloy. Among a series of Ir x Ru 1-x O y nanofibers, the cathodically activated Ir 0.80 Ru 0.20 O y shows the best HER activity and stability even compared with IrO y and RuO y , commercial Pt and commercial Ir (20 wt % each metal loading on Vulcan carbon), where a superior stability is possibly ascribed to the instant generation of active Ir and Ru metals on the catalyst surface upon HER. Density functional theory calculation results for hydrogen adsorption show that the energy and adsorbate-catalyst distance at metallic Ir 0.80 Ru 0.20 are close to those at Pt. This suggests that mixed metallic Ir and Ru are significant contributors to the improved HER activity of Ir 0.80 Ru 0.20 O y after the cathodic activation. The present findings clearly demonstrate that the mixed oxide of Ir and Ru is a very effective electrocatalytic system for HER.

  8. Preparation and characterization of electrospun PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels for skin tissue engineering.

    Directory of Open Access Journals (Sweden)

    Jian-feng Pan

    Full Text Available In this study, two different biomaterials were fabricated and their potential use as a bilayer scaffold for skin tissue engineering applications was assessed. The upper layer biomaterial was a Poly(ε-caprolactone-co-lactide/Poloxamer (PLCL/Poloxamer nanofiber membrane fabricated using electrospinning technology. The PLCL/Poloxamer nanofibers (PLCL/Poloxamer, 9/1 exhibited strong mechanical properties (stress/strain values of 9.37 ± 0.38 MPa/187.43 ± 10.66% and good biocompatibility to support adipose-derived stem cells proliferation. The lower layer biomaterial was a hydrogel composed of 10% dextran and 20% gelatin without the addition of a chemical crosslinking agent. The 5/5 dextran/gelatin hydrogel displayed high swelling property, good compressive strength, capacity to present more than 3 weeks and was able to support cells proliferation. A bilayer scaffold was fabricated using these two materials by underlaying the nanofibers and casting hydrogel to mimic the structure and biological function of native skin tissue. The upper layer membrane provided mechanical support in the scaffold and the lower layer hydrogel provided adequate space to allow cells to proliferate and generate extracellular matrix. The biocompatibility of bilayer scaffold was preliminarily investigated to assess the potential cytotoxicity. The results show that cell viability had not been affected when cocultured with bilayer scaffold. As a consequence, the bilayer scaffold composed of PLCL/Poloxamer nanofibers and dextran/gelatin hydrogels is biocompatible and possesses its potentially high application prospect in the field of skin tissue engineering.

  9. Treatment of alkali-injured cornea by cyclosporine A-loaded electrospun nanofibers - An alternative mode of therapy.

    Czech Academy of Sciences Publication Activity Database

    Čejková, Jitka; Čejka, Čestmír; Trošan, Peter; Zajícová, Alena; Syková, Eva; Holáň, Vladimír

    2016-01-01

    Roč. 147, may. (2016), s. 128-137 ISSN 0014-4835 R&D Projects: GA ČR(CZ) GA14-12580S; GA MZd(CZ) NT14102; GA MŠk(CZ) LO1309; GA MŠk(CZ) ED1.1.00/02.0109 Institutional support: RVO:68378041 Keywords : alkali injury * central corneal thickness * CsA-loaded nanofibers * immunohistochemistry Subject RIV: FF - HEENT, Dentistry Impact factor: 3.332, year: 2016

  10. Water-insoluble sericin/β-cyclodextrin/PVA composite electrospun nanofibers as effective adsorbents towards methylene blue.

    Science.gov (United States)

    Zhao, Rui; Wang, Yong; Li, Xiang; Sun, Bolun; Jiang, Ziqiao; Wang, Ce

    2015-12-01

    A novel water-insoluble sericin/β-cyclodextrin/poly (vinyl alcohol) composite nanofiber adsorbent was prepared by electrospinning and followed by thermal crosslinking for removal of cationic dye methylene blue from aqueous solution. Fourier transform infrared spectroscopy and solubility experiments confirmed that sericin and β-cyclodextrin were incorporated into the nanofibers and the crosslinking reaction occurred successfully. Kinetics, isotherms and thermodynamics analysis were studied for adsorption of methylene blue. The adsorption process is better fitted with the pseudo-second-order model and Langmuir isotherm model. The maximum adsorption capacities are 187.97, 229.89, and 261.10mg/g at the temperatures 293, 313 and 333 K, respectively. Thermodynamic parameters showed that methylene blue adsorption was endothermic and spontaneous. In addition, the fiber membrane adsorbent could be easily separated from dye solution and showed high recyclable removal efficiency. All these results suggest that crosslinked sericin/β-cyclodextrin/poly(vinyl alcohol) composite nanofibers could be potential recyclable adsorbents in dye wastewater treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Real-Time Characterization of Electrospun PVP Nanofibers as Sensitive Layer of a Surface Acoustic Wave Device for Gas Detection

    Directory of Open Access Journals (Sweden)

    D. Matatagui

    2014-01-01

    Full Text Available The goal of this work has been to study the polyvinylpyrrolidone (PVP fibers deposited by means of the electrospinning technique for using as sensitive layer in surface acoustic wave (SAW sensors to detect volatile organic compounds (VOCs. The electrospinning process of the fibers has been monitored and RF characterized in real time, and it has been shown that the diameters of the fibers depend mainly on two variables: the applied voltage and the distance between the needle and the collector, since all the electrospun fibers have been characterized by a scanning electron microscopy (SEM. Real-time measurement during the fiber coating process has shown that the depth of penetration of mechanical perturbation in the fiber layer has a limit. It has been demonstrated that once this saturation has been reached, the increase of the thickness of the fibers coating does not improve the sensitivity of the sensor. Finally, the parameters used to deposit the electrospun fibers of smaller diameters have been used to deposit fibers on a SAW device to obtain a sensor to measure different concentrations of toluene at room temperature. The present sensor exhibited excellent sensitivity, good linearity and repeatability, and high and fast response to toluene at room temperature.

  12. Distributed feedback imprinted electrospun fiber lasers.

    Science.gov (United States)

    Persano, Luana; Camposeo, Andrea; Del Carro, Pompilio; Fasano, Vito; Moffa, Maria; Manco, Rita; D'Agostino, Stefania; Pisignano, Dario

    2014-10-01

    Imprinted, distributed feedback lasers are demonstrated on individual, active electrospun polymer nanofibers. In addition to advantages related to miniaturization, optical confinement and grating nanopatterning lead to a significant threshold reduction compared to conventional thin-film lasers. The possibility of imprinting arbitrary photonic crystal geometries on electrospun lasing nanofibers opens new opportunities for realizing optical circuits and chips. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Biodegradable nanofibers-reinforced microfibrous composite scaffolds for bone tissue engineering.

    Science.gov (United States)

    Martins, Albino; Pinho, Elisabete D; Correlo, Vítor M; Faria, Susana; Marques, Alexandra P; Reis, Rui L; Neves, Nuno M

    2010-12-01

    Native bone extracellular matrix (ECM) is a complex hierarchical fibrous composite structure, resulting from the assembling of collagen fibrils at several length scales, ranging from the macro to the nanoscale. The combination of nanofibers within microfibers after conventional reinforcement methodologies seems to be a feasible solution to the rational design of highly functional synthetic ECM substitutes. The present work aims at the development of bone ECM inspired structures, conjugating electrospun chitosan (Cht) nanofibers within biodegradable polymeric microfibers [poly(butylene succinate)-PBS and PBS/Cht], assembled in a fiber mesh structure. The nanofibers-reinforced composite fiber mesh scaffolds were seeded with human bone marrow mesenchymal stem cells (hBMSCs) and cultured under osteogenic differentiation conditions. These nanofibers-reinforced composite scaffolds sustained ECM deposition and mineralization, mainly in the PBS/Cht-based fiber meshes, as depicted by the increased amount of calcium phosphates produced by the osteogenic differentiated hBMSCs. The osteogenic genotype of the cultured hBMSCs was confirmed by the expression of osteoblastic genes, namely Alkaline Phosphatase, Osteopontin, Bone Sialoprotein and Osteocalcin, and the transcription factors Runx2 and Osterix, all involved in different stages of the osteogenesis. These data represent the first report on the biological functionality of nanofibers-reinforced composite scaffolds, envisaging the applicability of the developed structures for bone tissue engineering.

  14. Cyclosporine A-loaded and stem cell-seeded electrospun nanofibers for cell-based therapy and local immunosuppression

    Czech Academy of Sciences Publication Activity Database

    Holáň, Vladimír; Chudíčková, Milada; Trošan, Peter; Svobodová, Eliška; Krulová, Magdalena; Kubinová, Šárka; Syková, Eva; Širc, Jakub; Michálek, Jiří; Juklíčková, M.; Munzarová, M.; Zajícová, Alena

    2011-01-01

    Roč. 156, č. 3 (2011), s. 406-412 ISSN 0168-3659 R&D Projects: GA AV ČR KAN200520804; GA ČR GAP304/11/0653; GA ČR(CZ) GAP301/11/1568; GA ČR GD310/08/H077; GA MŠk 1M0506 Institutional research plan: CEZ:AV0Z50390512; CEZ:AV0Z40500505; CEZ:AV0Z50520514 Keywords : nanofibers * immunosuppression * cell transfer Subject RIV: EC - Immunology Impact factor: 5.732, year: 2011

  15. Morphological Control of Mesoporosity and Nanoparticles within Co3O4-CuO Electrospun Nanofibers: Quantum Confinement and Visible Light Photocatalysis Performance.

    Science.gov (United States)

    Pradhan, Amaresh C; Uyar, Tamer

    2017-10-18

    The one-dimensional (1D) mesoporous and interconnected nanoparticles (NPs) enriched composite Co 3 O 4 -CuO nanofibers (NFs) in the ratio Co:Cu = 1/4 (Co 3 O 4 -CuO NFs) composite have been synthesized by electrospinning and calcination of mixed polymeric template. Not merely the mesoporous composite Co 3 O 4 -CuO NFs but also single mesoporous Co 3 O 4 NFs and CuO NFs have been produced for comparison. The choice of mixed polymer templates such as polyvinylpyrrolidone (PVP) and polyethylene glycol (PEG) for electrospinning is responsible for the formation of 1D mesoporous NFs. The HR-TEM result showed evolution of interconnected nanoparticles (NPs) and creation of mesoporosity in all electrospun NFs. The quantum confinement is due to NPs within NFs and has been proved by the surface-enhanced Raman scattering (SERS) study and the UV-vis-NRI diffuse reflectance spectra (DRS). The high intense photoluminescence (PL) spectra showing blue shift of all NFs also confirmed the quantum confinement phenomena. The lowering of PL spectrum after mixing of CuO in Co 3 O 4 nanofibers framework (Co 3 O 4 -CuO NFs) proved CuO as an efficient visible light response low cost cocatalyst/charge separator. The red shifting of the band gap in composite Co 3 O 4 -CuO NFs is due to the internal charge transfer between Co 2+ to Co 3+ and Cu 2+ , proved by UV-vis absorption spectroscopy. Creation of oxygen vacancies by mixing of CuO and Co 3 O 4 also prevents the electron-hole recombination and enhances the photocatalytic activity in composite Co 3 O 4 -CuO NFs. The photocurrent density, Mott-Schottky (MS), and electrochemical impedance spectroscopy (EIS) studies of all NFs favor the high photocatalytic performance. The mesoporous composite Co 3 O 4 -CuO NFs exhibits high photocatalytic activity toward phenolic compounds degradation as compared to the other two NFs (Co 3 O 4 NFs and CuO NFs). The kinetic study of phenolic compounds followed first order rate equation. The high photocatalytic

  16. Fabrication of Ag nanoparticles embedded in TiO2 nanotubes: using electrospun nanofibers for controlling plasmonic effects.

    Science.gov (United States)

    Jung, Mi-Hee; Yun, Yong Ju; Chu, Moo-Jung; Kang, Man Gu

    2013-06-24

    Composites of electrospun poly(ethylene oxide) (PEO) fibers and silver nanoparticles (Ag NPs) were used as a soft template for coating with TiO2 by atomic layer deposition (ALD). Whereas the as-deposited TiO2 layers on PEO fibers and Ag NPs were completely amorphous, the TiO2 layers were transformed into polycrystalline TiO2 nanotubes (NTs) with embedded Ag NPs after calcination. Their plasmonic effect can be controlled by varying the thickness of the dielectric Al2 O3 spacer between Ag NPs and dye molecules by means of the ALD process. Electronic and spectroscopic analyses demonstrated enhanced photocurrent generation and solar-cell performance due to the intense electromagnetic field of the dye resulting from the surface plasmon effect of the Ag NPs. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Electrospun Polymer Blend Nanofibers for Tunable Drug Delivery: The Role of Transformative Phase Separation on Controlling the Release Rate.

    Science.gov (United States)

    Tipduangta, Pratchaya; Belton, Peter; Fábián, László; Wang, Li Ying; Tang, Huiru; Eddleston, Mark; Qi, Sheng

    2016-01-04

    Electrospun fibrous materials have a wide range of biomedical applications, many of them involving the use of polymers as matrices for incorporation of therapeutic agents. The use of polymer blends improves the tuneability of the physicochemical and mechanical properties of the drug loaded fibers. This also benefits the development of controlled drug release formulations, for which the release rate can be modified by altering the ratio of the polymers in the blend. However, to realize these benefits, a clear understanding of the phase behavior of the processed polymer blend is essential. This study reports an in depth investigation of the impact of the electrospinning process on the phase separation of a model partially miscible polymer blend, PVP K90 and HPMCAS, in comparison to other conventional solvent evaporation based processes including film casting and spin coating. The nanoscale stretching and ultrafast solvent removal of electrospinning lead to an enhanced apparent miscibility between the polymers, with the same blends showing micronscale phase separation when processed using film casting and spin coating. Nanoscale phase separation in electrospun blend fibers was confirmed in the dry state. Rapid, layered, macroscale phase separation of the two polymers occurred during the wetting of the fibers. This led to a biphasic drug release profile from the fibers, with a burst release from PVP-rich phases and a slower, more continuous release from HPMCAS-rich phases. It was noted that the model drug, paracetamol, had more favorable partitioning into the PVP-rich phase, which is likely to be a result of greater hydrogen bonding between PVP and paracetamol. This led to higher drug contents in the PVP-rich phases than the HPMCAS-rich phases. By alternating the proportions of the PVP and HPMCAS, the drug release rate can be modulated.

  18. Asymmetric supercapacitors based on functional electrospun carbon nanofiber/manganese oxide electrodes with high power density and energy density

    Science.gov (United States)

    Lin, Sheng-Chi; Lu, Yi-Ting; Chien, Yu-An; Wang, Jeng-An; You, Ting-Hsuan; Wang, Yu-Sheng; Lin, Chih-Wen; Ma, Chen-Chi M.; Hu, Chi-Chang

    2017-09-01

    Carbon nanofibers modified with carboxyl groups (CNF-COOH) possessing good wettability and high porosity are homogeneously deposited with amorphous manganese dioxide (amorphous MnO2) by potentiodynamic deposition for asymmetric super-capacitors (ASCs). The potential-cycling in 1 M H2SO4 successfully enhances the hydrophilicity of carbonized polymer nanofibers and facilitates the access of electrolytes within the CNF-COOH matrix. This modification favors the deposition of amorphous MnO2 and improves its electrochemical utilization. In this composite, MnO2 homogeneously dispersed onto CNF-COOH provides desirable pseudocapacitance and the CNF-COOH network works as the electron conductor. The composite of CNF-COOH@MnO2-20 shows a high specific capacitance of 415 F g-1 at 5 mV s-1. The capacitance retention of this composite is 94% in a 10,000-cycle test. An ASC cell consisting of this composite and activated carbon as positive and negative electrodes can be reversibly charged/discharged to a cell voltage of 2.0 V in 1 M Na2SO4 and 4 mM NaHCO3 with specific energy and power of 36.7 Wh kg-1 and 354.9 W kg-1, respectively. This ASC also shows excellent cell capacitance retention (8% decay) in the 2V, 10,000-cycle stability test, revealing superior performance.

  19. Electrospun Polyaniline-Based Composite Nanofibers: Tuning the Electrical Conductivity by Tailoring the Structure of Thiol-Protected Metal Nanoparticles

    Directory of Open Access Journals (Sweden)

    Filippo Pierini

    2017-01-01

    Full Text Available Composite nanofibers made of a polyaniline-based polymer blend and different thiol-capped metal nanoparticles were prepared using ex situ synthesis and electrospinning technique. The effects of the nanoparticle composition and chemical structure on the electrical properties of the nanocomposites were investigated. This study confirmed that Brust’s procedure is an effective method for the synthesis of sub-10 nm silver, gold, and silver-gold alloy nanoparticles protected with different types of thiols. Electron microscopy results demonstrated that electrospinning is a valuable technique for the production of composite nanofibers with similar morphology and revealed that nanofillers are well-dispersed into the polymer matrix. X-ray diffraction tests proved the lack of a significant influence of the nanoparticle chemical structure on the polyaniline chain arrangement. However, the introduction of conductive nanofillers in the polymer matrix influences the charge transport noticeably improving electrical conductivity. The enhancement of electrical properties is mediated by the nanoparticle capping layer structure. The metal nanoparticle core composition is a key parameter, which exerted a significant influence on the conductivity of the nanocomposites. These results prove that the proposed method can be used to tune the electrical properties of nanocomposites.

  20. Electrospun Nanofibers for Sandwiched Polyimide/Poly (vinylidene fluoride)/Polyimide Separators with the Thermal Shutdown Function

    International Nuclear Information System (INIS)

    Wu, Dezhi; Shi, Chuan; Huang, Shaohua; Qiu, Xiaochun; Wang, Huan; Zhan, Zhan; Zhang, Peng; Zhao, Jinbao; Sun, Daoheng; Lin, Liwei

    2015-01-01

    Nanofibers fabricated by the electrospinning process have been used to construct sandwich-type Polyimide/Poly (vinylidene fluoride)/Polyimide (PI/PVDF/PI) separators with the thermal shutdown function for lithium ion batteries. This architecture uses the good thermal stability of PI as the top and bottom structure layers. Under high temperature operations, the middle layer made of PVDF nanofibers can melt and form a pore-free film to shut down the battery operation. The electrolyte uptake and ionic conductivity of the PI/PVDF/PI separator are superior to those of commercial polyolefin separators at 476% and 3.46 mS cm −1 , respectively, resulting better battery performances in terms of impedance, discharge capacity and cycle life. Under high temperature treatments above 170 °C, the self-shutdown function of the PI/PVDF/PI has been observed within 10 minutes, which could serve as the safety mechanism to defend the thermal runaway issue of lithium ion batteries. The effects of heating temperature and different time on the morphologies of each layer and electrolyte uptake of the separator are characterized as well

  1. Porous worm-like NiMoO4 coaxially decorated electrospun carbon nanofiber as binder-free electrodes for high performance supercapacitors and lithium-ion batteries

    Science.gov (United States)

    Tian, Xiaodong; Li, Xiao; Yang, Tao; Wang, Kai; Wang, Hongbao; Song, Yan; Liu, Zhanjun; Guo, Quangui

    2018-03-01

    The peculiar architectures consisting of electrospun carbon nanofibers coaxially decorated by porous worm-like NiMoO4 were successfully fabricated for the first time to address the poor cycling stability and inferior rate capability of the state-of-the-art NiMoO4-based electrodes caused by the insufficient structural stability, dense structure and low conductivity. The porous worm-like structure endows the electrode high capacitance/capacity due to large effective specific surface area and short electron/ion diffusion channels. Moreover, the robust integrated electrode with sufficient internal spaces can self-accommodate volume variation during charge/discharge processes, which is beneficial to the structural stability and integrity. By the virtue of rational design of the architecture, the hybrid electrode delivered high specific capacitance (1088.5 F g-1 at 1 A g-1), good rate capability (860.3 F g-1 at 20 A g-1) and long lifespan with a capacitance retention of 73.9% after 5000 cycles when used as supercapacitor electrode. For lithium-ion battery application, the electrode exhibited a high reversible capacity of 1132.1 mAh g-1 at 0.5 A g-1. Notably, 689.7 mAh g-1 can be achieved even after 150 continuous cycles at a current density of 1 A g-1. In the view of their outstanding electrochemical performance and the cost-effective fabrication process, the integrated nanostructure shows great promising applications in energy storage.

  2. Biotechnology humic acids-based electrospun carbon nanofibers as cost-efficient electrodes for lithium-ion batteries

    International Nuclear Information System (INIS)

    Zhao, Pin-Yi; Guo, Yan; Yu, Bao-Jun; Zhang, Jie; Wang, Cheng-Yang

    2016-01-01

    Bio-based, cost-effective carbon nanofibers are fabricated from polyacrylonitrile (PAN) – refined biotechnology humic acids (RB) via simple eletrospinning after stabilization and carbonization. The influence of PAN/RB mass ratios and heat-treatment temperatures (HTTs) on structure and morphology is systematically studied. Excitingly, a first discharge/charge capacity of 937.9/613.4 mAh g −1 (coulombic efficiency of 65.4%) is achieved at 20 mA g −1 for PB7/3-800 in lithium-ion batteries (LIBs). Meanwhile, a charge capacity of 348.2 mAh g −1 (about 89% retention ratio) remains even after 100 cycles at 0.1 A g −1 . It is demonstrated that biomass humic acids can be applied as a promising precursor to fabricate high performance, low-cost, as well as “green” carbon electrode material for LIBs.

  3. Degradation of the electrospun silica nanofiber in a biological medium for primary hippocampal neuron – effect of surface modification

    Directory of Open Access Journals (Sweden)

    Feng ZV

    2016-02-01

    Full Text Available Z Vivian Feng,1,* Wen Shuo Chen,2,* Khomson Keratithamkul,1 Michael Stoick,1 Brittany Kapala,3 Eryn Johnson,3 An-Chi Huang,2 Ting Yu Chin,4 Yui Whei Chen-Yang,2 Mong-Lin Yang3 1Chemistry Department, Augsburg College, Minneapolis, MN, USA; 2Department of Chemistry, Center for Nanotechnology, Center for Biomedical Technology, Chung Yuan Christian University, Chung Li, Taiwan, Republic of China; 3Department of Science, Concordia University Saint Paul, Saint Paul, MN, USA; 4Department of Bioscience Technology, Chung Yuan Christian University, Chung Li, Taiwan, Republic of China *These authors contributed equally to this work Abstract: In this work, silica nanofibers (SNFs were prepared by an electrospinning method and modified with poly-D-lysine (PDL or (3-aminopropyl trimethoxysilane (APTS making biocompatible and degradable substrates for neuronal growth. The as-prepared SNF, modified SNF-PDL, and SNF-APTS were evaluated using scanning electron microscopy, nitrogen adsorption/desorption isotherms, contact angle measurements, and inductively coupled plasma atomic emission spectroscopy. Herein, the scanning electron microscopic images revealed that dissolution occurred in a corrosion-like manner by enlarging porous structures, which led to loss of structural integrity. In addition, covalently modified SNF-APTS with more hydrophobic surfaces and smaller surface areas resulted in significantly slower dissolution compared to SNF and physically modified SNF-PDL, revealing that different surface modifications can be used to tune the dissolution rate. Growth of primary hippocampal neuron on all substrates led to a slower dissolution rate. The three-dimensional SNF with larger surface area and higher surface density of the amino group promoted better cell attachment and resulted in an increased neurite density. This is the first known work addressing the degradability of SNF substrate in physiological conditions with neuron growth in vitro, suggesting a

  4. Covalent immobilization of xylanase produced from Bacillus pumilus SV-85S on electrospun polymethyl methacrylate nanofiber membrane.

    Science.gov (United States)

    Kumar, Pankaj; Gupta, Ashish; Dhakate, Sanjay R; Mathur, Rakesh B; Nagar, Sushil; Gupta, Vijay K

    2013-01-01

    Polymethyl methacrylate (PMMA) nanofiber membrane (NFM) was synthesized by an electrospinning technique. These membranes were utilized as a support for immobilization of xylanase enzyme to study its pH stability, thermal stability, and reusability. The morphology of aligned NFM was studied by optical microscopy and scanning electron microscopy. The PMMA NFM was functionalized with phenylenediamine and activated with glutaraldehyde to yield an aldehyde group on its surface for covalent immobilization of xylanase. The Fourier transform infrared analysis of the covalently immobilized xylanase confirmed that the enzyme was immobilized on PMMA NFM via amide linkages. The immobilization efficiency of covalently bound xylanase was found experimentally to be 90%. A forward shift in pH optima from 6.0-7.0 (soluble enzyme) to 7.0-9.0 (immobilized enzyme) was observed after xylanase immobilization. The pH and temperature stability of xylanase were enhanced upon its covalent immobilization. The immobilized enzyme was active on repeated use and retained ∼80% of its initial activity after 11 reaction cycles. The improved thermal and operational stability of the covalently immobilized enzyme on PMMA NFM might be advantageous for industrial applications. © 2013 International Union of Biochemistry and Molecular Biology, Inc.

  5. On Stabilization of PVPA/PVA Electrospun Nanofiber Membrane and Its Effect on Material Properties and Biocompatibility

    Directory of Open Access Journals (Sweden)

    Rose Ann Franco

    2012-01-01

    Full Text Available A novel nanofiber membrane was fabricated by electrospinning composed of polyvinyl phosphonic acid (PVPA and polyvinyl alcohol (PVA. Stabilization was done due to the high dissolvability of the membrane when in contact with water. Physical treatment was done by exposure to heat at 150°C in a vacuum environment at different periods of time. Chemical crosslinking was done by immersion in methanol and methanol/ glutaraldehyde. A heat-exposed membrane was also further crosslinked chemically. All conditions were compared with regards to its effect on the material properties of the membranes and its biological response in vitro with MG-63 osteoblast-like cell line. Visual examination and dimensional analyses showed that heat treatment produced discoloration on the membrane surface and chemical crosslinking reduced membrane dimensions. Tensile strength and strain improved in crosslinked membranes compared to noncrosslinked counterpart. Swelling and degradation was also investigated and was seen to vary depending on the crosslinking condition. Biocompatibility was observed to be more favorable in heat-treated membranes.

  6. Free-standing and mechanically flexible mats consisting of electrospun carbon nanofibers made from a natural product of alkali lignin as binder-free electrodes for high-performance supercapacitors

    Science.gov (United States)

    Lai, Chuilin; Zhou, Zhengping; Zhang, Lifeng; Wang, Xiaoxu; Zhou, Qixin; Zhao, Yong; Wang, Yechun; Wu, Xiang-Fa; Zhu, Zhengtao; Fong, Hao

    2014-02-01

    Mechanically flexible mats consisting of electrospun carbon nanofibers (ECNFs) were prepared by first electrospinning aqueous mixtures containing a natural product of alkali lignin together with polyvinyl alcohol (PVA) into composite nanofiber mats followed by stabilization in air and carbonization in an inert environment. Morphological and structural properties, as well as specific surface area, total pore volume, average pore size, and pore size distribution, of the lignin-based ECNF mats were characterized; and their electrochemical performances (i.e., capacitive behaviors) were evaluated by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy. The lignin-based ECNF mats exhibited outstanding performance as free-standing and/or binder-free electrodes of supercapacitors. For example, the ECNFs made from the composite nanofibers with mass ratio of lignin/PVA being 70/30 (i.e., ECNFs (70/30)) had the average diameter of ∼100 nm and the Brunauer-Emmett-Teller (BET) specific surface area of ∼583 m2 g-1. The gravimetric capacitance of ECNFs (70/30) electrode in 6 M KOH aqueous electrolyte exhibited 64 F g-1 at current density of 400 mA g-1 and 50 F g-1 at 2000 mA g-1. The ECNFs (70/30) electrode also exhibited excellent cycling durability/stability, and the gravimetric capacitance merely reduced by ∼10% after 6000 cycles of charge/discharge.

  7. A Novel Approach to Limit Chemical Deterioration of Gilthead Sea Bream (Sparus aurata) Fillets: Coating with Electrospun Nanofibers as Characterized by Molecular, Thermal, and Microstructural Properties.

    Science.gov (United States)

    Ceylan, Zafer; Sengor, Gulgun F Unal; Yilmaz, Mustafa Tahsin

    2017-05-01

    Coating of sea bream fillets with thymol loaded chitosan based electrospun nanofibers (TLCN) and chitosan based nanafibers (CN) has been presented a novel approach to delay chemical deterioration. We assessed CN and TLCN with respect of scanting of total volatile basic nitrogen (TVBN), trimethylamine (TMA), thiobarbituric acid (TBA) deterioration during cold storage condition. Electrospinning process was applied to obtain TLCN and CN. Both of nanofibers obtained from biopolymer and bioactive material were cylindrical, smooth, beadless. Thermal, molecular, zeta potential (ZP), and surface properties of the groups were investigated, revealing that CN indicated molecular interactions with thymol in nanofibers, reduce in physical properties of these structures, thermal decomposition (an alteration in mass of CN and TLCN at temperatures below 190 °C, corresponding to 20.53% and 19.97%, respectively) and also dispersion stabilities (ζ potential) of CN and TLCN were determined 33.68 ± 3.35 and 21.85 ± 1.96 mV, respectively. TVBN and TMA stability analyses demonstrated that CN and TLCN were both effective in delaying chemical deterioration of fish fillets, furthermore TLCN was more effective against chemical deterioration. TBA analyses results of fish fillets indicated that CN and TLCN delayed rancidity in fish meat as compared to control group samples. The presented study results suggested that coating of the sea bream fillets with CN and TLCN would be a promising approach to delay the chemical deterioration of fish fillets. © 2017 Institute of Food Technologists®.

  8. Hierarchically Structured Electrospun Fibers

    Science.gov (United States)

    2013-01-07

    been made from the contraction of a manganese oxide sol gel upon solvent evaporation, as well as from zinc oxide and silicon dioxide using vapor...H.; Shin, Y.M.; Terai, H.; Vacanti, J.P. A biodegradable nanofiber scaffold by electrospinning and its potential for bone tissue engineering...D.L. Electrospun silk-BMP-2 scaffolds for bone tissue engineering. Biomaterials 2006, 27, 3115–3124. 28. Zhang, Y.Z.; Ouyang, H.W.; Lim, C.T

  9. Enhanced NH3 gas sensing performance based on electrospun alkaline-earth metals composited SnO2 nanofibers

    International Nuclear Information System (INIS)

    Xu, Shuang; Kan, Kan; Yang, Ying; Jiang, Chao; Gao, Jun; Jing, Liqiang; Shen, Peikang; Li, Li

    2015-01-01

    Highlights: • The small-sized SnO 2 (5–7 nm) were obtained by adding the alkaline-earth. • Sr-composited SnO 2 nanofibers showed uniform nanotubes structure (Sr/SnO 2 ). • Sr/SnO 2 showed an excellent sensing performance to NH 3 at room temperature. - Abstract: One-dimensional alkaline-earth metals composited SnO 2 (Ae/SnO 2 ) nanofibres were fabricated via electrospinning technique, followed by thermal treatment at 600 °C for 5 h. Transmission electron microscopy (TEM) studies showed that the nanoparticles size of Ae/SnO 2 was 5–7 nm, which was smaller than the pristine SnO 2 nanorods attached by 20 nm nanoparticles. Moreover, Sr/SnO 2 nanocomposites showed uniform nanotubes structure with the wall thickness of about 30 nm, in which all the nanoparticles were connected to their neighbors by necks. The Sr/SnO 2 nanotubes exhibited an excellent sensing response toward NH 3 gas at room temperature, lower detection limit (10 ppm), faster response time (6 s towards 2000 ppm∼16 s towards 10 ppm) and better reversibility compared to the pristine SnO 2 nanorods. The enhanced sensor performances were attributed to the higher conductivity of the Sr/SnO 2 . Mott–Schottky plots (M–S) and electrochemical impedance spectroscopy (EIS) measurements indicated that the carrier density of Sr/SnO 2 nanotubes was 3 fold of that pristine SnO 2

  10. Biocomposite scaffolds based on electrospun poly(3-hydroxybutyrate) nanofibers and electrosprayed hydroxyapatite nanoparticles for bone tissue engineering applications

    International Nuclear Information System (INIS)

    Ramier, Julien; Bouderlique, Thibault; Stoilova, Olya; Manolova, Nevena; Rashkov, Iliya; Langlois, Valérie; Renard, Estelle; Albanese, Patricia; Grande, Daniel

    2014-01-01

    The electrospinning technique combined with the electrospraying process provides a straightforward and versatile approach for the fabrication of novel nanofibrous biocomposite scaffolds with structural, mechanical, and biological properties potentially suitable for bone tissue regeneration. In this comparative investigation, three types of poly(3-hydroxybutyrate) (PHB)-based scaffolds were engineered: (i) PHB mats by electrospinning of a PHB solution, (ii) mats of PHB/hydroxyapatite nanoparticle (nHA) blends by electrospinning of a mixed solution containing PHB and nHAs, and (iii) mats constituted of PHB nanofibers and nHAs by simultaneous electrospinning of a PHB solution and electrospraying of a nHA dispersion. Scaffolds based on PHB/nHA blends displayed improved mechanical properties compared to those of neat PHB mats, due to the incorporation of nHAs within the fibers. The electrospinning/electrospraying approach afforded biocomposite scaffolds with lower mechanical properties, due to their higher porosity, but they displayed slightly better biological properties. In the latter case, the bioceramic, i.e. nHAs, largely covered the fiber surface, thus allowing for a direct exposure to cells. The 21 day-monitoring through the use of MTS assays and SEM analyses demonstrated that human mesenchymal stromal cells (hMSCs) remained viable on PHB/nHA biocomposite scaffolds and proliferated continuously until reaching confluence. - Highlights: • Three different types of PHB-based scaffolds are engineered and thoroughly investigated. • The combination of electrospinning and electrospraying affords original nanofibrous biocomposite scaffolds. • PHB-based scaffolds show a strong capability of supporting viable cell development for 21 days

  11. Abdominal closure reinforcement by using polypropylene mesh functionalized with poly-epsilon-caprolactone nanofibers and growth factors for prevention of incisional hernia formation

    Czech Academy of Sciences Publication Activity Database

    Plencner, Martin; East, B.; Tonar, Z.; Otáhal, M.; Prosecká, Eva; Rampichová, Michala; Krejčí, T.; Litvinec, Andrej; Buzgo, Matej; Míčková, Andrea; Nečas, A.; Hoch, J.; Amler, Evžen

    2014-01-01

    Roč. 9, č. 1 (2014), s. 3263-3277 E-ISSN 1178-2013 R&D Projects: GA MŠk CZ.1.05/1.1.00/02.0068 Grant - others:GA MŠk(CZ) project IPv6; GA UK(CZ) 545313; GA UK(CZ) 384311; GA UK(CZ) 270513; GA UK(CZ) 424213; GA UK(CZ) 648112; GA MZd(CZ) NT12156; GA MŠk(CZ) ED2.1.00/03.0076; Středoevropský technologický institut CZ.1.05/1.1.00/02.0068 Institutional support: RVO:68378041 Keywords : nanofibers * growth factors * surgical mesh Subject RIV: FP - Other Medical Disciplines Impact factor: 4.383, year: 2014

  12. Silver nanoparticles immobilized onto polycaprolactone (PCL)/poly[2-(dimethylamino)ethyl metacrilate) nanofiber meshes; Imobilizacao de nanoparticulas de prata em malhas de nanofibras de poli(caprolactona)/poli[(2-dimetilamino)etil metacrilato

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Fernanda G.; Bonkovoski, Leticia C.; Witt, Maria A.; Rubira, Adley F.; Muniz, Edvani C. [Universidade Estadual de Maringa (GMPC/UEM), Maringa, PR (Brazil). Grupo de Materiais Polimericos e Compositos; Piai, Juliana F., E-mail: jupiai@yahoo.com.br [Universidade Estadual de Maringa (UEM), Umuarama, PR (Brazil)

    2015-07-01

    The present work comprises the fabrication of nanofiber meshes of polycaprolactone (PCL)/poly [(2-dimethylamino) ethyl methacrylate] (PDMAEMA) and the subsequent immobilization of silver nanoparticles, in order to obtain materials with potential application in tissue engineering. The nanofibers composed of different ratios of PDMAEMA / PCL (m/m) were obtained by electrospinning. These nanofiber meshes were then immersed in colloidal suspensions containing the AgNPs under different pH values to immobilize the nanoparticles onto the fiber's surface. A greater amount of AgNPs was deposited when the fibers were immersed in a solution of pH 5, as one can observe from the scanning electron microscopy (SEM) images and the X-ray spectroscopy (EDS) spectra. It was observed that the meshes of the blends suffered morphological changes after immersion in acid solution (pH 5), and, the deposition of AgNPs onto the meshes in general was more effective in acid environment (pH 5). (author)

  13. Fabrication of Conductive Polypyrrole Nanofibers by Electrospinning

    Directory of Open Access Journals (Sweden)

    Yiqun Cong

    2013-01-01

    Full Text Available Electrospinning is employed to prepare conductive polypyrrole nanofibers with uniform morphology and good mechanical strength. Soluble PPy was synthesized with NaDEHS as dopant and then applied to electrospinning with or without PEO as carrier. The PEO contents had great influence on the morphology and conductivity of the electrospun material. The results of these experiments will allow us to have a better understanding of PPy electrospun nanofibers and will permit the design of effective electrodes in the BMIs fields.

  14. Clinical outcomes for teeth treated with electrospun poly(ε-caprolactone) fiber meshes/mineral trioxide aggregate direct pulp capping.

    Science.gov (United States)

    Lee, Li-Wan; Hsiao, Sheng-Huang; Hung, Wei-Chiang; Lin, Yun-Ho; Chen, Po-Yu; Chiang, Chun-Pin

    2015-05-01

    Mineral trioxide aggregate (MTA) is a biocompatible material for direct pulp capping. This study was designed to compare the clinical outcomes of pulp-exposed teeth treated with either poly(ε-caprolactone) fiber mesh (PCL-FM) as a barrier for MTA (so-called PCL-FM/MTA) or MTA direct pulp capping. Sixty human vital teeth were evenly divided into 4 groups (n = 15 in each group). Teeth in groups 1 and 3 had pulp exposure MTA direct pulp capping, and those in groups 3 and 4 were treated with MTA direct pulp capping. Teeth treated with PCL-FM/MTA direct pulp capping needed a significantly shorter mean duration for dentin bridge formation than teeth treated with MTA direct pulp capping. Moreover, teeth with pulp exposure MTA or MTA direct pulp capping treatment. In addition, teeth treated with PCL-FM/MTA direct pulp capping formed an approximately 3-fold thicker dentin bridge than teeth treated with MTA direct pulp capping 8 weeks or 3 months later. Furthermore, none of the teeth treated with PCL-FM/MTA direct pulp capping showed tooth discoloration after treatment for 3 months. PCL-FM/MTA is a better combination material than MTA alone for direct pulp capping of human permanent teeth. Copyright © 2015 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  15. Electrospun Borneol-PVP Nanocomposites

    Directory of Open Access Journals (Sweden)

    Xiao-Yan Li

    2012-01-01

    Full Text Available The present work investigates the validity of electrospun borneol-polyvinylpyrrolidone (PVP nanocomposites in enhancing drug dissolution rates and improving drug physical stability. Based on hydrogen bonding interactions and via an electrospinning process, borneol and PVP can form stable nanofiber-based composites. FESEM observations demonstrate that composite nanofibers with uniform structure could be generated with a high content of borneol up to 33.3% (w/w. Borneol is well distributed in the PVP matrix molecularly to form the amorphous composites, as verified by DSC and XRD results. The composites can both enhance the dissolution profiles of borneol and increase its physical stability against sublimation for long-time storage by immobilization of borneol molecules with PVP. The incorporation of borneol in the PVP matrix weakens the tensile properties of nanofibers, and the mechanism is discussed. Electrospun nanocomposites can be alternative candidates for developing novel nano-drug delivery systems with high performance.

  16. Alkali-Mediated Miscibility of Gelatin/Polycaprolactone for Electrospinning Homogeneous Composite Nanofibers for Tissue Scaffolding

    NARCIS (Netherlands)

    Zhou, Qihui; Zhang, Huilan; Zhou, Ya; Yu, Zhepao; Yuan, Huihua; Feng, Bei; van Rijn, Patrick; Zhang, Yanzhong

    2017-01-01

    Electrospun natural-synthetic composite nanofibers, which possess favorable biological and mechanical properties, have gained widespread attention in tissue engineering. However, the development of biomimetic nanofibers of hybrids remains a huge challenge due to phase separation of the polymer

  17. Increasing Mechanical Properties of 2-D-Structured Electrospun Nylon 6 Non-Woven Fiber Mats

    OpenAIRE

    Xiang, Chunhui; Frey, Margaret W.

    2016-01-01

    Tensile strength, Young’s modulus, and toughness of electrospun nylon 6 non-woven fiber mats were improved by increasing individual nanofiber strength and fiber–fiber load sharing. Single-walled carbon nanotubes (CNTs) were used as reinforcement to increase the strength of the electrospun nylon 6 nanofibers. Young’s modulus, tensile strength, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % solutions increased 51%, 87%, and 136%, respectively, after incorporating 1 w...

  18. Electrospinning of Nanofibers for Energy Applications

    Directory of Open Access Journals (Sweden)

    Guiru Sun

    2016-07-01

    Full Text Available With global concerns about the shortage of fossil fuels and environmental issues, the development of efficient and clean energy storage devices has been drastically accelerated. Nanofibers are used widely for energy storage devices due to their high surface areas and porosities. Electrospinning is a versatile and efficient fabrication method for nanofibers. In this review, we mainly focus on the application of electrospun nanofibers on energy storage, such as lithium batteries, fuel cells, dye-sensitized solar cells and supercapacitors. The structure and properties of nanofibers are also summarized systematically. The special morphology of nanofibers prepared by electrospinning is significant to the functional materials for energy storage.

  19. Electrospinning of Nanofibers for Energy Applications

    Science.gov (United States)

    Sun, Guiru; Sun, Liqun; Xie, Haiming; Liu, Jia

    2016-01-01

    With global concerns about the shortage of fossil fuels and environmental issues, the development of efficient and clean energy storage devices has been drastically accelerated. Nanofibers are used widely for energy storage devices due to their high surface areas and porosities. Electrospinning is a versatile and efficient fabrication method for nanofibers. In this review, we mainly focus on the application of electrospun nanofibers on energy storage, such as lithium batteries, fuel cells, dye-sensitized solar cells and supercapacitors. The structure and properties of nanofibers are also summarized systematically. The special morphology of nanofibers prepared by electrospinning is significant to the functional materials for energy storage. PMID:28335256

  20. Enhanced bone formation in electrospun poly(L-lactic-co-glycolic acid)–tussah silk fibroin ultrafine nanofiber scaffolds incorporated with graphene oxide

    International Nuclear Information System (INIS)

    Shao, Weili; He, Jianxin; Sang, Feng; Wang, Qian; Chen, Li; Cui, Shizhong; Ding, Bin

    2016-01-01

    To engineer bone tissue, it is necessary to provide a biocompatible, mechanically robust scaffold. In this study, we fabricated an ultrafine nanofiber scaffold by electrospinning a blend of poly(L-lactic-co-glycolic acid), tussah silk fibroin, and graphene oxide (GO) and characterized its morphology, biocompatibility, mechanical properties, and biological activity. The data indicate that incorporation of 10 wt.% tussah silk and 1 wt.% graphene oxide into poly(L-lactic-co-glycolic acid) nanofibers significantly decreased the fiber diameter from 280 to 130 nm. Furthermore, tussah silk and graphene oxide boosted the Young's modulus and tensile strength by nearly 4-fold and 3-fold, respectively, and significantly enhanced adhesion, proliferation in mouse mesenchymal stem cells and functionally promoted biomineralization-relevant alkaline phosphatase (ALP) and mineral deposition. The results indicate that composite nanofibers could be excellent and versatile scaffolds for bone tissue engineering. - Highlights: • GO-doped PLGA–tussah silk fibroin ultrafine nanofibers with diameter of about 130 nm were fabricated by electrospinning. • Incorporation of 10 wt.% tussah silk to the PLGA nanofibers accelerates osteoblast differentiation and formation of new bone. • Mechanical properties of composite nanofiber mats had been significantly improved after embedding with GO nanosheets. • Nanostructured composite scaffolds effectively accelerate mesenchymal stem cells differentiation and formation of new bone.

  1. Enhanced bone formation in electrospun poly(L-lactic-co-glycolic acid)–tussah silk fibroin ultrafine nanofiber scaffolds incorporated with graphene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Shao, Weili [Key Laboratory of Advanced Textile Composites (Ministry of Education), Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Henan Provincial Key Laboratory of Functional Textile Materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); He, Jianxin, E-mail: hejianxin771117@163.com [Henan Provincial Key Laboratory of Functional Textile Materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Sang, Feng [Department of Acquired Immune Deficiency Syndrome Treatment and Research Center, The First Affiliated Hospital of Henan University of Traditional Chinese Medicine, Zhengzhou 450000 (China); Wang, Qian [Henan Provincial Key Laboratory of Functional Textile Materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Chen, Li [Key Laboratory of Advanced Textile Composites (Ministry of Education), Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Cui, Shizhong [Key Laboratory of Advanced Textile Composites (Ministry of Education), Institute of Textile Composites, Tianjin Polytechnic University, Tianjin 300387 (China); Henan Provincial Key Laboratory of Functional Textile Materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); Ding, Bin [Henan Provincial Key Laboratory of Functional Textile Materials, Zhongyuan University of Technology, Zhengzhou 450007 (China); State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials Science and Engineering, Donghua University, Shanghai 201600 (China)

    2016-05-01

    To engineer bone tissue, it is necessary to provide a biocompatible, mechanically robust scaffold. In this study, we fabricated an ultrafine nanofiber scaffold by electrospinning a blend of poly(L-lactic-co-glycolic acid), tussah silk fibroin, and graphene oxide (GO) and characterized its morphology, biocompatibility, mechanical properties, and biological activity. The data indicate that incorporation of 10 wt.% tussah silk and 1 wt.% graphene oxide into poly(L-lactic-co-glycolic acid) nanofibers significantly decreased the fiber diameter from 280 to 130 nm. Furthermore, tussah silk and graphene oxide boosted the Young's modulus and tensile strength by nearly 4-fold and 3-fold, respectively, and significantly enhanced adhesion, proliferation in mouse mesenchymal stem cells and functionally promoted biomineralization-relevant alkaline phosphatase (ALP) and mineral deposition. The results indicate that composite nanofibers could be excellent and versatile scaffolds for bone tissue engineering. - Highlights: • GO-doped PLGA–tussah silk fibroin ultrafine nanofibers with diameter of about 130 nm were fabricated by electrospinning. • Incorporation of 10 wt.% tussah silk to the PLGA nanofibers accelerates osteoblast differentiation and formation of new bone. • Mechanical properties of composite nanofiber mats had been significantly improved after embedding with GO nanosheets. • Nanostructured composite scaffolds effectively accelerate mesenchymal stem cells differentiation and formation of new bone.

  2. Optimization, synthesis, and characterization of coaxial electrospun sodium carboxymethyl cellulose-graft-methyl acrylate/poly(ethylene oxide) nanofibers for potential drug-delivery applications.

    Science.gov (United States)

    Esmaeili, Akbar; Haseli, Mahsa

    2017-10-01

    In this study, nanofiber drug carriers were fabricated via coaxial electrospinning, using a new, degradable core-shell nanofiber drug carrier fabricated via coaxial electrospinning. Fabrication of the shell was carried out by graft polymerization of sodium carboxymethyl cellulose (NaCMC) with methyl acrylate (TCMC) and poly(ethylene oxide) (PEO). Tetracycline hydrochloride (TCH) was used as a drug model incorporated within the nanofibers as the core, and their performance as a drug carrier scaffold was evaluated. The loading of TCH within PEO nanofibers and the loading of TCH within the TCMC nanofibers were characterized via different techniques. The structure morphology of the obtained nanofibers was viewed under scanning electron microscope (SEM). The changes in the polymer structure before and after grafting and confirmation of incorporation of the drug in the fibers were characterized by Fourier transform infrared spectroscopy (FT-IR). Response surface methodology (RSM) was applied to predict the optimum conditions for fabrication of the nanofibers. The cell viability of the optimized samples was assessed with 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay. The TCH loaded into the optimized core-shell sample of TCMC 3% (w/v)/PEO 1% (w/v) had a smooth and beadless morphology with a diameter of 86.12nm, slow and sustained drug release, and excellent bactericidal activity against a wide range of bacteria. This shows promise for use as an antibacterial material in such applications as tissue engineering and pharmaceutical science. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. A facile fabrication of nitrogen-doped electrospun In{sub 2}O{sub 3} nanofibers with improved visible-light photocatalytic activity

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Na; Shao, Changlu, E-mail: clshao@nenu.edu.cn; Li, Xinghua, E-mail: lixh781@nenu.edu.cn; Miao, Fujun; Wang, Kexin; Liu, Yichun

    2017-01-01

    Highlights: • N-doped In{sub 2}O{sub 3} nanofibers are facilely fabricated by gaseous ammonia treatment. • Adjusting the annealing temperature leads to different N-doped In{sub 2}O{sub 3} nanofibers. • Nitrogen doping was found to be interstitial mode. • N-In{sub 2}O{sub 3} exhibited effective charge carrier separation and photocatalytic activity. • The photocatalysts can be easily separated from the reaction system. - Abstract: Semiconductor photocatalysis demonstrates to be an effective approach for eliminating most types of environment contaminants and for producing hydrogen. Herein, a facile synthesis route combining electrospinning technique and thermal treatment method under NH{sub 3} atmosphere has been presented as a straightforward protocol for the fabrication of nitrogen-doped In{sub 2}O{sub 3} (N-In{sub 2}O{sub 3}) nanofibers, the nitrogen content of which can be well controlled by adjusting the annealing temperature. Photocatalytic tests show that the N-In{sub 2}O{sub 3} nanofibers demonstrate an improved degradation rate of Rhodamine B (RB) compared with pure In{sub 2}O{sub 3} nanofibers under visible-light irradiation. This can be attributed to the nitrogen atom introducing at interstitial sites as well as the generation of oxygen vacancy on the surface of In{sub 2}O{sub 3} nanofibers, resulting in the enhanced utilization of visible light for the N-In{sub 2}O{sub 3} nanofibers. Furthermore, the obtained N-In{sub 2}O{sub 3} nanofibers with the advantage of ultra-long one-dimensional nanostructures can be recycled several times by facile sedimentation and hence present almost no decrease in photocatalytic activity indicative of a well regeneration capability. Therefore, the as-fabricated nitrogen-doped In{sub 2}O{sub 3} nanofibers as a promising photocatalyst present good photocatalytic degradation of organic pollutant in waste water for practical application.

  4. Novel-structured electrospun TiO2/CuO composite nanofibers for high efficient photocatalytic cogeneration of clean water and energy from dye wastewater.

    Science.gov (United States)

    Lee, Siew Siang; Bai, Hongwei; Liu, Zhaoyang; Sun, Darren Delai

    2013-08-01

    It is still a challenge to photocatalytically cogenerate clean water and energy from dye wastewater owing to the relatively low photocatalytic efficiency of photocatalysts. In this study, novel-structured TiO2/CuO composite nanofibers were successfully fabricated via facile electrospinning. For the first time, the TiO2/CuO composite nanofibers demonstrated multifunctional ability for concurrent photocatalytic organic degradation and H2 generation from dye wastewater. The enhanced photocatalytic activity of TiO2/CuO composite nanofibers was ascribed to its excellent synergy of physicochemical properties: 1) mesoporosity and large specific surface area for efficient substrate adsorption, mass transfer and light harvesting; 2) red-shift of the absorbance spectra for enhanced light utilization; 3) long nanofibrous structure for efficient charge transfer and ease of recovery, 4) TiO2/CuO heterojunctions which enhance the separation of electrons and holes and 5) presence of CuO which serve as co-catalyst for the H2 production. The TiO2/CuO composite nanofibers also exhibited rapid settleability by gravity and uncompromised reusability. Thus, the as-synthesized TiO2/CuO composite nanofibers represent a promising candidate for highly efficient concurrent photocatalytic organic degradation and clean energy production from dye wastewater. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. Role of CdO addition on the growth and photocatalytic activity of electrospun ZnO nanofibers: UV vs. visible light

    Science.gov (United States)

    Samadi, Morasae; Pourjavadi, Ali; Moshfegh, A. Z.

    2014-04-01

    (ZnO)1-x(CdO)x nanofibers were fabricated via electrospinning of polymer precursor by subsequent annealing in air. Field emission scanning electron microscopy (FESEM) showed the smooth and beadless nanofibers and X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) showed the ZnO hexagonal and the CdO cubic structure. Diffuse reflectance spectroscopy (DRS) showed the band gap energy reduction by increasing the amount of CdO in (ZnO)1-x(CdO)x nanofibers that resulted in the photocatalytic activity under the visible light for dye degradation. Under the UV light CdO acted as both electron and hole sink in the (ZnO)1-x(CdO)x nanofibers and a possible photocatalytic activity mechanism was proposed. The effect of annealing rate on the nanofiber properties was also studied. Thermal gravimetric analysis (TGA) plot revealed that different heating rates influence on both peak position and maximum amount of decomposition. Improvement of the crystallinity and the increase in the photocatalytic activity were obtained by increasing the annealing rate from 3 to 20 °C/min.

  6. Piezoelectric properties of electrospun nanofibers of BaTiO3; Propiedades piezoeletricas de nanofibras eletrofiadas de BaTiO3

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, L.F.R.M.; Melo, G.F.; Goncalves, A.M.; Eiras, J.A.; Bretas, R.E.S., E-mail: bretas@ufscar.br [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil)

    2016-07-01

    BaTiO3 nanofibers were produced by the electrospinning method from a mixture of a solution of the precursors Ba (CH{sub 3}COO){sub 2} and [(CH{sub 3}){sub 2}CHO]{sub 4}Ti in acetic acid and a solution of poly(vinylpyrrolidone) in ethanol. A voltage of 10 kV and a working distance of 4.6 cm were used for the electrospinning, at controlled room temperature and humidity of 21 °C and 60% respectively. Nanofibers as spun were dried in air on an air-circulating oven at 100 °C for one hour to remove residual solvent and were subsequently calcined at 750 °C during 2 h. The morphology, crystallographic structure and piezoelectric properties of the nanofibers were analyzed by scanning electron microscopy (SEM), X-ray angle (WAXS) and Piezoresponse Force Microscopy (PFM), respectively. The average diameter of the nanofibers was 414 nm with an aspect ratio of 40. By PFM, there was strong evidence that the nanofibers had piezoelectric activity. (author)

  7. Electrospun hierarchical LiV3O8 nanofibers assembled from nanosheets with exposed {100} facets and their enhanced performance in aqueous lithium-ion batteries.

    Science.gov (United States)

    Liang, Lin; Zhou, Min; Xie, Yi

    2012-03-05

    Hierarchical LiV(3)O(8) nanofibers, assembled from nanosheets that have exposed {100} facets, have been fabricated by using electrospinning combined with calcination. The formation mechanism of hierarchical nanofibers was investigated by X-ray diffraction and scanning electron microscopy. Poly(vinyl alcohol) (PVA) played a dual role in the formation of the nanofibers: besides acting as the template for forming the fibers, it effectively prevented the aggregation of LiV(3)O(8) nanoparticles, thereby allowing them to grow into small nanosheets with exposed {100} facets owing to the self-limitation property of LiV(3)O(8). This nanostructure is beneficial for the insertion/extraction of lithium ions. Meanwhile, the {100} facets have fewer and smaller channels, which may effectively alleviate proton co-intercalation into the electrode materials. Hence, the hierarchical LiV(3)O(8) nanofibers exhibit higher discharge capacities and better cycling stabilities as the anode electrode material for aqueous lithium-ion batteries than those reported previously. We demonstrate that these hierarchical nanofibers have promising potential applications in aqueous lithium-ion batteries. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Processing and characterization of electrospun Y2O3-stabilized ZrO2 (YSZ) and Gd2O3-doped CeO2 (GDC) nanofibers

    International Nuclear Information System (INIS)

    Azad, Abdul-Majeed; Matthews, Thomas; Swary, Jessica

    2005-01-01

    The technique of electrospinning was employed to fabricate uniform one-dimensional (1-D) inorganic-organic composite nanofibers from alcoholic solutions containing polyvinyl pyrrolidone (PVP) and suitable aqueous precursors of yttrium and zirconium ions in one case and gadolinium and cerium ions in the other. Upon firing and sintering under carefully pre-selected time-temperature profiles (heating rate, temperature and soak time), ceramic nanofibers retaining the original morphological features observed in the as-spun composition were obtained. Analytical tools, such as simultaneous TG-DSC, Raman spectroscopy and SEM were employed to elucidate the pathway of ceramic phase formation and the systematic evolution of morphological features in the spun and the processed fibers. X-ray diffraction was used to identify the crystalline fate of the final products. It was found that several millimeter long, uniform YSZ and GDC nanofibers of high phase purity could be fabricated

  9. Wiping frictional properties of electrospun hydrophobic/hydrophilic polyurethane nanofiber-webs on soda-lime glass and silicon-wafer.

    Science.gov (United States)

    Watanabe, Kei; Wei, Kai; Nakashima, Ryu; Kim, Ick Soo; Enomoto, Yuji

    2013-04-01

    In the present work, we conducted the frictional tests of hydrophobic and hydrophilic polyurethane (PUo and PUi) nanofiber webs against engineering materials; soda-lime glass and silicon wafer. PUi/glass combination, with highest hydrophilicity, showed the highest friction coefficient which decrease with the increase of the applied load. Furthermore, the effects of fluorine coating are also investigated. The friction coefficient of fluorine coated hydrophobic PU nanofiber (PUof) shows great decrease against the silicon wafer. Finally, wiping ability and friction property are investigated when the substrate surface is contaminated. Nano-particle dusts are effectively collected into the pores by wiping with PUo and PUi nanofiber webs both on glass and silicon wafer. The friction coefficient gradually increased with the increase of the applied load.

  10. Enhanced bone formation in electrospun poly(L-lactic-co-glycolic acid)-tussah silk fibroin ultrafine nanofiber scaffolds incorporated with graphene oxide.

    Science.gov (United States)

    Shao, Weili; He, Jianxin; Sang, Feng; Wang, Qian; Chen, Li; Cui, Shizhong; Ding, Bin

    2016-05-01

    To engineer bone tissue, it is necessary to provide a biocompatible, mechanically robust scaffold. In this study, we fabricated an ultrafine nanofiber scaffold by electrospinning a blend of poly(L-lactic-co-glycolic acid), tussah silk fibroin, and graphene oxide (GO) and characterized its morphology, biocompatibility, mechanical properties, and biological activity. The data indicate that incorporation of 10 wt.% tussah silk and 1 wt.% graphene oxide into poly(L-lactic-co-glycolic acid) nanofibers significantly decreased the fiber diameter from 280 to 130 nm. Furthermore, tussah silk and graphene oxide boosted the Young's modulus and tensile strength by nearly 4-fold and 3-fold, respectively, and significantly enhanced adhesion, proliferation in mouse mesenchymal stem cells and functionally promoted biomineralization-relevant alkaline phosphatase (ALP) and mineral deposition. The results indicate that composite nanofibers could be excellent and versatile scaffolds for bone tissue engineering. Copyright © 2016 Elsevier B.V. All rights reserved.

  11. Regulating drug release from pH- and temperature-responsive electrospun CTS-g-PNIPAAm/poly(ethylene oxide) hydrogel nanofibers.

    Science.gov (United States)

    Yuan, Huihua; Li, Biyun; Liang, Kai; Lou, Xiangxin; Zhang, Yanzhong

    2014-08-18

    Temperature- and pH-responsive polymers have been widely investigated as smart drug release systems. However, dual-sensitive polymers in the form of nanofibers, which is advantageous in achieving rapid transfer of stimulus to the smart polymeric structures for regulating drug release behavior, have rarely been explored. In this study, chitosan-graft-poly(N-isopropylacrylamide) (CTS-g-PNIPAAm) copolymer was synthesized by using 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC) and N-hydroxy succinimide (NHS) as grafting agents to graft carboxyl-terminated PNIPAAm (PNIPAAm-COOH) chains onto the CTS biomacromolecules, and then CTS-g-PNIPAAm with or without bovine serum albumin (BSA) was fabricated into nanofibers through electrospinning using poly(ethylene oxide) (PEO, 10 wt%) as a fiber-forming facilitating additive. The BSA laden CTS-g-PNIPAAm/PEO hydrogel nanofibers were tested to determine their drug release profiles by varying pH and temperature. Finally, cytotoxicity of the CTS-g-PNIPAAm/PEO hydrogel nanofibers was evaluated by assaying the L929 cell proliferation using the MTT method. It was found that the synthesized CTS-g-PNIPAAm possessed a temperature-induced phase transition and lower critical solution temperature (LCST) at 32° C in aqueous solutions. The rate of BSA release could be well modulated by altering the environmental pH and temperature of the hydrogel nanofibers. The CTS-g-PNIPAAm/PEO hydrogel nanofibers supported L929 cell growth, indicative of appropriate cytocompatibility. Our current work could pave the way towards developing multi-stimuli responsive nanofibrous smart materials for potential applications in the fields of drug delivery and tissue engineering.

  12. Electrospun UiO-66/polyacrylonitrile nanofibers as efficient sorbent for pipette tip solid phase extraction of phytohormones in vegetable samples.

    Science.gov (United States)

    Yan, Zhiming; Wu, Mei; Hu, Biqing; Yao, Minna; Zhang, Lan; Lu, Qiaomei; Pang, Jie

    2018-03-23

    In this work, metal-organic framework particles incorporated fibers (UiO-66/PAN nanofibers) were used as adsorbent in pipette tip solid phase extraction (PT-SPE) for the first time. The UiO-66/PAN nanofibers were fabricated by a facile electrospinning method and characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and nitrogen adsorption-desorption experiments. The UiO-66/PAN nanofibers were applied to assemble a novel PT-SPE cartridge for determination of four phytohormones followed by high performance liquid chromatography (HPLC). Several experimental parameters such as kinds of UiO-66/PAN nanofibers, the amount of UiO-66/PAN nanofibers, the effect of solution pH, ionic strength and desorption conditions were intensively investigated. Under the optimal conditions, the linear ranges of the phytohormones were in the range of 0.06-60 ng/mL with correlation coefficients above 0.992. The limits of detection were between 0.01 ng/mL to 0.02 ng/mL. The interday and intraday precision (RSD) for three replicate extractions of the four phytohormones (15 ng/mL for each) was in the range of 1.5-5.6%. The established method was successfully applied for the determination of phytohormones in watermelon and mung bean sprouts samples. The results showed that the electrostatic interaction between the positively charged UiO-66 and anionic forms of phytohormones played an important role in the extraction of the phytohormones. Copyright © 2018 Elsevier B.V. All rights reserved.

  13. Development of mats composed by TiO{sub 2} and carbon dual electrospun nanofibers: A possible anode material in microbial fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Gomez, Nora A.; Balderas-Renteria, Isaias [Universidad Autónoma de Nuevo León, Facultad de Ciencias Químicas, Av. Universidad S/N Cd. Universitaria San Nicolás de los Garza Nuevo León, C.P. 66451 México (Mexico); Garcia-Gutierrez, Domingo I. [Universidad Autónoma de Nuevo León, Facultad de Ingeniería Mecánica y Eléctrica, Av. Universidad S/N Cd. Universitaria San Nicolás de los Garza Nuevo León, C.P. 66451 México (Mexico); Universidad Autónoma de Nuevo León, Centro de Innovación, Investigación y Desarrollo en Ingeniería y Tecnología, PIIT, Av. Universidad S/N Cd. Universitaria San Nicolás de los Garza Nuevo León, C.P. 66451 México (Mexico); Mosqueda, Hugo A. [Universidad Autónoma de Nuevo León, Facultad de Ingeniería Mecánica y Eléctrica, Av. Universidad S/N Cd. Universitaria San Nicolás de los Garza Nuevo León, C.P. 66451 México (Mexico); and others

    2015-03-15

    Highlights: • Dual nanofiber of TiO{sub 2}–C/C showed excellent electrical performance. • TiO{sub 2}–C/C dual nanofiber can host a dense biofilm of electroactivated Escherichia coli. • Dual nanofibers can be applied as anode to obtain electricity in microbial fuel cells. - Abstract: A new material based on TiO{sub 2(rutile)}–C{sub (semi-graphitic)}/C{sub (semi-graphitic)} dual nanofiber mats is presented, whose composition and synthesis methodology are fundamental factors for the development of exoelectrogenic biofilms on its surface. Therefore, this material shows the required characteristics for possible applications in the bioconversion process of an organic substrate to electricity in a microbial fuel cell. Chronoamperometry, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and electrical conductivity analyses showed excellent electrical performance of the material for the application intended; a resistance as low as 3.149 Ω was able to be measured on this material. Furthermore, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies confirmed the morphology sought on the material for the application intended, dual nanofibres TiO{sub 2(rutile)}–C{sub (semi-graphitic)}/C{sub (semi-graphitic)} with a side by side configuration. The difference in composition of the fibers forming the dual nanofibers was clearly observed and confirmed by energy dispersive X-ray spectroscopy (EDXS), and their crystal structure was evident in the results obtained from selected area electron diffraction (SAED) studies. This nanostructured material presented a high surface area and is biocompatible, given that it can host a dense biofilm of electroactivated Escherichia coli. In this study, the maximum current density obtained in a half microbial fuel cell was 8 A/m{sup 2} (0.8 mA/cm{sup 2})

  14. A fabricated electro-spun sensor based on Lake Red C pigments doped into PAN (polyacrylonitrile) nano-fibers for electrochemical detection of Aflatoxin B1 in poultry feed and serum samples.

    Science.gov (United States)

    Babakhanian, Arash; Momeneh, Tahereh; Aberoomand-azar, Parviz; Kaki, Samineh; Torki, Mehran; Hossein Kiaie, Seyed; Sadeghi, Ehsan; Dabirian, Farzad

    2015-11-21

    The aim of this work was to fabricate a novel nano-fiber modified electrode, involving Lake Red C (LRC) pigments doped into electrospun polyacrylonitrile (PAN) fibrous films. Cyclic voltammetry (CV), scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and differential pulse voltammetry (DPV) techniques were used for electrochemical and morphological characterization of the composite fibers. This sensor responds to Aflatoxin B1 (AFB1) over the concentration range of 40-120 nM with high accuracy and precision in analysis. The modified electrode exhibited an excellent electrocatalytic ability (α = 0.42, log K(s) = 4.21 s(-1), and Γ = 1.49 × 10(-5) mmol cm(-2)) for reduction of AFB1 at the optimum pH of 6 and working potential of -0.75 V (vs. SCE). The common substances accompanying AFB1 had no serious interferences on the response of the modified electrode to AFB1. The modified electrode indicated reproducible behavior and a high level stability during the experiments, making it particularly suitable for the analytical determination of AFB1 in poultry feed and serum samples.

  15. Electrical Conductivity Improvement of Polyvinyl Alcohol Nanofiber by Solvent Vapour Treatment

    OpenAIRE

    - Chotimah; Aditya Rianjanu; Bimo Winardianto; Misbachul Munir; Indriana Kartini; Kuwat Triyana

    2016-01-01

    The electrical conductivity of polyvinyl alcohol (PVA) electrospun nanofibers is naturally low. For an electrical device application, it requires high enough conductivity. The objective of this study is to improve the electrical conductivity of electrospun PVA nanofibers with and without poly (3,4-ethylenedioxytriophene): polystyrene sulfonate (PEDOT:PSS) by exposure polar solvent of dimethyl sulfoxide (DMSO). For this purpose, the nanofibers were deposited on a substrate with patterned elect...

  16. Discovery of the beta-form crystal structure in electrospun nanofibers of bio-based poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyhexanoate] and its implication on properties

    Science.gov (United States)

    Gong, Liang

    Bacterially produced poly[(R)-3-hydroxybutyrate-co-(R)-3-hydroxyhexanoate] (PHBHx) is a new type of bioplastic which not only inherits the excellent biodegradability and biocompatibility of its parent homopolymer, polyhydroxybutyrate (PHB), but also overcomes PHB’s brittleness and stiffness with the incorporation of 3-hydroxyhexanoate (Hx) comonomer units with medium-chain-length (mcl) side chains. The tough and ductile PHBHx, with a much lower crystallinity and melting temperature, is well-suited for many practical applications. Efforts have been made to broaden the application range of PHBHx by introducing the beta-form crystalline structure, where the molecular chains adopt a planar zig-zag conformation. However, it is extremely difficult to produce this beta-form in PHBHx due to its much lower crystallinity and much more flexible molecular chains. In this study, we report an approach using the technique of electrospinning. The strain-induced metastable β-form crystalline structure was successfully introduced in PHBHx by collecting the macroscopically aligned electrospun PHBHx nanofibers across the air gap on a piece of aluminum foil and on the tapered edge of a high-speed rotary disk. The presence of the β-form crystal structure in electrospun fiber mats was confirmed by wide-angle X-ray diffraction (WAXD) and Fourier transform infrared spectroscopy (FTIR), with molecular orientation of the polymer chains along the fiber axis revealed by polarized FTIR. Selected area electron diffraction (SAED) and AFM-IR were utilized to investigate the morphological and structural details of individual PHBHx nanofibers. The results demonstrated a coexistence of the thermodynamically stable α-form crystalline structure, where molecular chains adopt a left-handed 21 helical conformation, and the β-form in single fibers. The molecular orientation level and the relative amounts of the two crystalline polymorphs were found to be highly dependent on fiber collection methods

  17. Biologically Inspired Nanofibers for Use in Translational Bioanalytical Systems

    Science.gov (United States)

    Matlock-Colangelo, Lauren; Baeumner, Antje J.

    2014-06-01

    Electrospun nanofiber mats are characterized by large surface-area-to-volume ratios, high porosities, and a diverse range of chemical functionalities. Although electrospun nanofibers have been used successfully to increase the immobilization efficiency of biorecognition elements and improve the sensitivity of biosensors, the full potential of nanofiber-based biosensing has not yet been realized. Therefore, this review presents novel electrospun nanofiber chemistries developed in fields such as tissue engineering and drug delivery that have direct application within the field of biosensing. Specifically, this review focuses on fibers that directly encapsulate biological additives that serve as immobilization matrices for biological species and that are used to create biomimetic scaffolds. Biosensors that incorporate these nanofibers are presented, along with potential future biosensing applications such as the development of cell culture and in vivo sensors.

  18. Cell proliferation on PVA/sodium alginate and PVA/poly(γ-glutamic acid) electrospun fiber

    International Nuclear Information System (INIS)

    Yang, Jen Ming; Yang, Jhe Hao; Tsou, Shu Chun; Ding, Chian Hua; Hsu, Chih Chin; Yang, Kai Chiang; Yang, Chun Chen; Chen, Ko Shao; Chen, Szi Wen; Wang, Jong Shyan

    2016-01-01

    To overcome the obstacles of easy dissolution of PVA nanofibers without crosslinking treatment and the poor electrospinnability of the PVA cross-linked nanofibers via electrospinning process, the PVA based electrospun hydrogel nanofibers are prepared with post-crosslinking method. To expect the electrospun hydrogel fibers might be a promising scaffold for cell culture and tissue engineering applications, the evaluation of cell proliferation on the post-crosslinking electrospun fibers is conducted in this study. At beginning, poly(vinyl alcohol) (PVA), PVA/sodium alginate (PVASA) and PVA/poly(γ-glutamic acid) (PVAPGA) electrospun fibers were prepared by electrospinning method. The electrospun PVA, PVASA and PVAPGA nanofibers were treated with post-cross-linking method with glutaraldehyde (Glu) as crosslinking agent. These electrospun fibers were characterized with thermogravimetry analysis (TGA) and their morphologies were observed with a scanning electron microscope (SEM). To support the evaluation and explanation of cell growth on the fiber, the study of 3T3 mouse fibroblast cell growth on the surface of pure PVA, SA, and PGA thin films is conducted. The proliferation of 3T3 on the electrospun fiber surface of PVA, PVASA, and PVAPGA was evaluated by seeding 3T3 fibroblast cells on these crosslinked electrospun fibers. The cell viability on electrospun fibers was conducted with water-soluble tetrazolium salt-1 assay (Cell Proliferation Reagent WST-1). The morphology of the cells on the fibers was also observed with SEM. The results of WST-1 assay revealed that 3T3 cells cultured on different electrospun fibers had similar viability, and the cell viability increased with time for all electrospun fibers. From the morphology of the cells on electrospun fibers, it is found that 3T3 cells attached on all electrospun fiber after 1 day seeded. Cell–cell communication was noticed on day 3 for all electrospun fibers. Extracellular matrix (ECM) productions were found and

  19. Cell proliferation on PVA/sodium alginate and PVA/poly(γ-glutamic acid) electrospun fiber

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jen Ming, E-mail: jmyang@mail.cgu.edu.tw [Department of Chemical and Materials Engineering, Chang Gung University, Taoyuan 333, Taiwan, ROC (China); Yang, Jhe Hao [Department of Electronic Engineering, Chang Gung University, Taoyuan, Taiwan, ROC (China); Tsou, Shu Chun; Ding, Chian Hua [Department of Chemical and Materials Engineering, Chang Gung University, Taoyuan 333, Taiwan, ROC (China); Hsu, Chih Chin [Department of Physical Medicine and Rehabilitation, Chang Gung Memorial Hospital at Keelung, Keelung, Taiwan, ROC (China); School of Traditional Chinese Medicine, Chang Gung University, Taoyuan, Taiwan, ROC (China); Yang, Kai Chiang [School of Biomedical Engineering, College of Biomedical Engineering, Taipei Medical University, Taipei 11031, Taiwan, ROC (China); Yang, Chun Chen [Department of Chemical Engineering, Ming-Chi University of Science and Technology, New Taipei City, Taiwan, ROC (China); Chen, Ko Shao [Department of Materials Engineering, Tatung University, Taipei, Taiwan, ROC (China); Chen, Szi Wen [Department of Electronic Engineering, Chang Gung University, Taoyuan, Taiwan, ROC (China); Wang, Jong Shyan [Department of Physical Therapy and the Graduate Institute of Rehabilitation Science, Chang Gung University, Taoyuan, Taiwan, ROC (China)

    2016-09-01

    To overcome the obstacles of easy dissolution of PVA nanofibers without crosslinking treatment and the poor electrospinnability of the PVA cross-linked nanofibers via electrospinning process, the PVA based electrospun hydrogel nanofibers are prepared with post-crosslinking method. To expect the electrospun hydrogel fibers might be a promising scaffold for cell culture and tissue engineering applications, the evaluation of cell proliferation on the post-crosslinking electrospun fibers is conducted in this study. At beginning, poly(vinyl alcohol) (PVA), PVA/sodium alginate (PVASA) and PVA/poly(γ-glutamic acid) (PVAPGA) electrospun fibers were prepared by electrospinning method. The electrospun PVA, PVASA and PVAPGA nanofibers were treated with post-cross-linking method with glutaraldehyde (Glu) as crosslinking agent. These electrospun fibers were characterized with thermogravimetry analysis (TGA) and their morphologies were observed with a scanning electron microscope (SEM). To support the evaluation and explanation of cell growth on the fiber, the study of 3T3 mouse fibroblast cell growth on the surface of pure PVA, SA, and PGA thin films is conducted. The proliferation of 3T3 on the electrospun fiber surface of PVA, PVASA, and PVAPGA was evaluated by seeding 3T3 fibroblast cells on these crosslinked electrospun fibers. The cell viability on electrospun fibers was conducted with water-soluble tetrazolium salt-1 assay (Cell Proliferation Reagent WST-1). The morphology of the cells on the fibers was also observed with SEM. The results of WST-1 assay revealed that 3T3 cells cultured on different electrospun fibers had similar viability, and the cell viability increased with time for all electrospun fibers. From the morphology of the cells on electrospun fibers, it is found that 3T3 cells attached on all electrospun fiber after 1 day seeded. Cell–cell communication was noticed on day 3 for all electrospun fibers. Extracellular matrix (ECM) productions were found and

  20. Physical and Chemical Properties of Pan-Derived Electrospun Activated Carbon Nanofibers and Their Potential for Use As An Adsorbent for Toxic Industrial Chemicals (Postprint)

    Science.gov (United States)

    2012-09-14

    carbon fiber cloth (ACFC) and Calgon BPL™ granular activated carbon (GAC) 2 Methods 2.1 Precursor selection and nonwoven nanofiber material preparation...respirators, re- generative filter systems that can protect against TICs, or perhaps smaller and more energy-efficient pressure-swing- adsorption systems...Peterson, G.W., Karwacki, C.: Novel collective protection filters for emerging TIC requirements: axial- and radial-flow filter de- signs. Edgewood Chemical

  1. Biofunctionalized Nanofibers Using Arthrospira (Spirulina Biomass and Biopolymer

    Directory of Open Access Journals (Sweden)

    Michele Greque de Morais

    2015-01-01

    Full Text Available Electrospun nanofibers composed of polymers have been extensively researched because of their scientific and technical applications. Commercially available polyhydroxybutyrate (PHB and polyhydroxybutyrate-co-valerate (PHB-HV copolymers are good choices for such nanofibers. We used a highly integrated method, by adjusting the properties of the spinning solutions, where the cyanophyte Arthrospira (formally Spirulina was the single source for nanofiber biofunctionalization. We investigated nanofibers using PHB extracted from Spirulina and the bacteria Cupriavidus necator and compared the nanofibers to those made from commercially available PHB and PHB-HV. Our study assessed nanofiber formation and their selected thermal, mechanical, and optical properties. We found that nanofibers produced from Spirulina PHB and biofunctionalized with Spirulina biomass exhibited properties which were equal to or better than nanofibers made with commercially available PHB or PHB-HV. Our methodology is highly promising for nanofiber production and biofunctionalization and can be used in many industrial and life science applications.

  2. Biofunctionalized nanofibers using Arthrospira (Spirulina) biomass and biopolymer.

    Science.gov (United States)

    de Morais, Michele Greque; Stillings, Christopher; Dersch, Roland; Rudisile, Markus; Pranke, Patrícia; Costa, Jorge Alberto Vieira; Wendorff, Joachim

    2015-01-01

    Electrospun nanofibers composed of polymers have been extensively researched because of their scientific and technical applications. Commercially available polyhydroxybutyrate (PHB) and polyhydroxybutyrate-co-valerate (PHB-HV) copolymers are good choices for such nanofibers. We used a highly integrated method, by adjusting the properties of the spinning solutions, where the cyanophyte Arthrospira (formally Spirulina) was the single source for nanofiber biofunctionalization. We investigated nanofibers using PHB extracted from Spirulina and the bacteria Cupriavidus necator and compared the nanofibers to those made from commercially available PHB and PHB-HV. Our study assessed nanofiber formation and their selected thermal, mechanical, and optical properties. We found that nanofibers produced from Spirulina PHB and biofunctionalized with Spirulina biomass exhibited properties which were equal to or better than nanofibers made with commercially available PHB or PHB-HV. Our methodology is highly promising for nanofiber production and biofunctionalization and can be used in many industrial and life science applications.

  3. Electrospun Fibers for Energy, Electronic, & Environmental Applications

    Science.gov (United States)

    Bedford, Nicholas M.

    Electrospinning is an established method for creating polymer and bio-polymer fibers of dimensions ranging from ˜10 nanometers to microns. The process typically involves applying a high voltage between a solution source (usually at the end of a capillary or syringe) and a substrate on which the nanofibers are deposited. The high electric field distorts the shape of the liquid droplet, creating a Taylor cone. Additional applied voltage ejects a liquid jet of the polymer solution in the Taylor cone toward the counter electrode. The formation of fibers is generated by the rapid electrostatic elongation and solvent evaporation of this viscoelastic jet, which typically generates an entangled non-woven mesh of fibers with a high surface area to volume ratio. Electrospinning is an attractive alternative to other processes for creating nano-scale fibers and high surface area to volume ratio surfaces due to its low start up cost, overall simplicity, wide range of processable materials, and the ability to generate a moderate amount of fibers in one step. It has also been demonstrated that coaxial electrospinning is possible, wherein the nanofiber has two distinct phases, one being the core and another being the sheath. This method is advantageous because properties of two materials can be combined into one fiber, while maintaining two distinct material phases. Materials that are inherently electrospinable could be made into fibers using this technique as well. The most common applications areas for electrospun fibers are in filtration and biomedical areas, with a comparatively small amount of work done in energy, environmental, and sensor applications. Furthermore, the use of biologically materials in electrospun fibers is an avenue of research that needs more exploration, given the unique properties these materials can exhibit. The research aim of this thesis is to explore the use of electrospun fibers for energy, electrical and environmental applications. For energy

  4. Fabrication of Cationic Exchange Polystyrene Nanofibers for Drug ...

    African Journals Online (AJOL)

    Trop J Pharm Res, February 2014; 13(2): 192. Many polymers are used to produce nanofibers by electrospinning. Polystyrene (PS) is one of polymers used to produce cation exchange fibers. [9]. PS nanofibers were successfully produced using the electrospinning method and it has been demonstrated that electrospun PS.

  5. Studies on single polymer composites of poly(methyl methacrylate) reinforced with electrospun nanofibers with a focus on their dynamic mechanical properties

    CSIR Research Space (South Africa)

    Matabola, KP

    2011-07-01

    Full Text Available for all the compos- ites. The addition of a 10 wt% nanofiber loading had no significant effect on the maximum value of the tan! peaks of the composites. Thus, the mobility of the polymer chains in the matrix and the composites are quite similar... review. Progress in Polymer Science, 35, 1288?1310 (2010). DOI: 10.1016/j.progpolymsci.2010.07.002 [2] Capiati N. J., Porter P. S.: The concept of one polymer composites modelled with high density polyethylene. Journal of Materials Science, 10...

  6. Fabrication of shape memory nanofibers by electrospinning method

    Science.gov (United States)

    Zhang, Fenghua; Zhang, Zhichun; Liu, Yanju; Leng, Jinsong

    2013-04-01

    Shape memory nanofibers are capable of fixing a temporary shape and recovering a permanent shape in response to stimulus. Nafion nanofibers with shape memory effect are achieved via electrospinning technology. The resulting nanofibres exhibit the smooth, continuous, uniform fibrous structure. The diameter of nanofibers increases after annealing progress at different temperatures. The shape memory effect is evaluated in a fixed force controlled tensile test. Electrospun Nafion nanofibers show excellent shape memory properties upon heat. The shape fixity rates and shape recovery rates are about 95-96% and 87-89% after consecutive three shape memory cycles, respectively. The structure of electrospun nanofibers is stable and reversible for at least three cycles of shape memory tests. These results indicate that shape memory Nafion nanofibers can be used in a wide potential application fields such as smart materials and structures in the future.

  7. In vitro fibroblast migration by sustained release of PDGF-BB loaded in chitosan nanoparticles incorporated in electrospun nanofibers for wound dressing applications.

    Science.gov (United States)

    Piran, Mehrdad; Vakilian, Saeid; Piran, Mehran; Mohammadi-Sangcheshmeh, Abdollah; Hosseinzadeh, Simzar; Ardeshirylajimi, Abdolreza

    2018-01-23

    Migration of fibroblasts into wound area is a critical phenomenon in wound healing process. We used an appropriate system to fabricate an electrospun bioactive scaffold with controlled release of PDGF-BB in order to induce migration of primary skin fibroblast cells. First of all, protein-loaded chitosan nanoparticles based on ionic gelation interaction between chitosan and sodium tripolyphosphate were prepared. Then polycaprolactone electrospun fibers containing chitosan nanoparticles or PDGF-BB-loaded chitosan nanoparticles were prepared. Cellular attachment and morphology of cells seeded on scaffolds with or without PDGF-BB were evaluated by using a fluorescence microscope and scanning electron microscopy. Cells were well-oriented 72 h after seeding on the scaffolds containing PDGF-BB. The mean aspect ratio of populations on scaffold containing PDGF-BB-loaded chitosan nanoparticles was significantly greater than those on the scaffold containing chitosan nanoparticles but no PDGF-BB. Furthermore, the Arp2 gene, which is involved in cell protrusion formation, showed about three times more expression at mRNA level, in cells seeding on PDGF-BB-containing scaffold compared to cells seeding on scaffold containing only chitosan nanoparticles, using Real Time PCR test. Finally, under agarose migration assay results demonstrated that cells' chemotaxic behavior was more toward scaffold containing PDGF-BB compared to the PDGF-BB alone or FBS group. In addition, in terms of distance, the cell mass could grow faster, in response to scaffold containing PDGF-BB compared to FBS or PDGF-BB alone; however, the number of migrating cells might be the same or significantly higher in the latter groups.

  8. A super hydrophilic modification of poly(vinylidene fluoride) (PVDF) nanofibers: By in situ hydrothermal approach

    Science.gov (United States)

    Sheikh, Faheem A.; Zargar, Mohammad Afzal; Tamboli, Ashif H.; Kim, Hern

    2016-11-01

    Nanofibers fabricated from Poly(vinylidene fluoride) (PVDF) possesses potential applications in the field of filtrations, because of their excellent resistance towards harsh chemicals. However, the hydrophobicity restricts its further application. In this work, we focus on optimal parameters for post-electrospun tethering of Poly(vinyl alcohol) (PVA) as superhydrophilic domain onto each individual PVDF nanofibers by exploiting the in situ hydrothermal approach. The results indicated an increase in nanofiber diameters due to coating of PVA and improved surface wettability of PVDF nanofibers. The tensile tests of nanofibers indicated that mechanical properties of PVDF nanofibers could be sharply tuned from rigid to ductile. Furthermore, the studies strongly suggest that in situ hydrothermal treatment of post-electrospun nanofibers can improve the water contact angle and these nanofibers can be used in varied applications (e.g., in water purification systems).

  9. Electrospun polyacrylonitrile nanofibrous biomaterials.

    Science.gov (United States)

    Ren, Xuehong; Akdag, Akin; Zhu, Changyun; Kou, Lei; Worley, S D; Huang, T S

    2009-11-01

    An N-halamine precursor, 3-(5'-methyl-5'-hydantoinyl)acetanilide (I), was synthesized in our laboratory and loaded onto electrospun polyacrylonitrile fiber to prepare nanosized biocidal materials, which could be rendered antimicrobial by exposure to household bleach. Differential scanning calorimetry was used to study the thermal properties of the nanofibers with and without the N-halamine precursor and its chlorinated derivative loaded. Scanning electron microscopy demonstrated that the ultrafine fibers formed with diameters from 250 to 600 nm. Chlorinated nanofibrous mats composed of the fibers were challenged with Staphylococcus aureus (ATCC 6538) and Escherichia coli O157:H7 (ATCC 43895); they showed promising inactivation efficacies against the two bacterial species within 5 minutes of contact. Potential uses of the antimicrobial fibers include filters for industrial water and air disinfection and protective clothing. (c) 2008 Wiley Periodicals, Inc.

  10. Optical fiber ultrasound transmitter with electrospun carbon nanotube-polymer composite

    Science.gov (United States)

    Poduval, Radhika K.; Noimark, Sacha; Colchester, Richard J.; Macdonald, Thomas J.; Parkin, Ivan P.; Desjardins, Adrien E.; Papakonstantinou, Ioannis

    2017-05-01

    All-optical ultrasound transducers are promising for imaging applications in minimally invasive surgery. In these devices, ultrasound is transmitted and received through laser modulation, and they can be readily miniaturized using optical fibers for light delivery. Here, we report optical ultrasound transmitters fabricated by electrospinning an absorbing polymer composite directly onto the end-face of optical fibers. The composite coating consisting of an aqueous dispersion of multi-walled carbon nanotubes (MWCNTs) in polyvinyl alcohol was directly electrospun onto the cleaved surface of a multimode optical fiber and subsequently dip-coated with polydimethylsiloxane (PDMS). This formed a uniform nanofibrous absorbing mesh over the optical fiber end-face wherein the constituent MWCNTs were aligned preferentially along individual nanofibers. Infiltration of the PDMS through this nanofibrous mesh onto the underlying substrate was observed and the resulting composites exhibited high optical absorption (>97%). Thickness control from 2.3 μm to 41.4 μm was obtained by varying the electrospinning time. Under laser excitation with 11 μJ pulse energy, ultrasound pressures of 1.59 MPa were achieved at 1.5 mm from the coatings. On comparing the electrospun ultrasound transmitters with a dip-coated reference fabricated using the same constituent materials and possessing identical optical absorption, a five-fold increase in the generated pressure and wider bandwidth was observed. The electrospun transmitters exhibited high optical absorption, good elastomer infiltration, and ultrasound generation capability in the range of pressures used for clinical pulse-echo imaging. All-optical ultrasound probes with such transmitters fabricated by electrospinning could be well-suited for incorporation into catheters and needles for diagnostics and therapeutic applications.

  11. Optical fiber ultrasound transmitter with electrospun carbon nanotube-polymer composite.

    Science.gov (United States)

    Poduval, Radhika K; Noimark, Sacha; Colchester, Richard J; Macdonald, Thomas J; Parkin, Ivan P; Desjardins, Adrien E; Papakonstantinou, Ioannis

    2017-05-29

    All-optical ultrasound transducers are promising for imaging applications in minimally invasive surgery. In these devices, ultrasound is transmitted and received through laser modulation, and they can be readily miniaturized using optical fibers for light delivery. Here, we report optical ultrasound transmitters fabricated by electrospinning an absorbing polymer composite directly onto the end-face of optical fibers. The composite coating consisting of an aqueous dispersion of multi-walled carbon nanotubes (MWCNTs) in polyvinyl alcohol was directly electrospun onto the cleaved surface of a multimode optical fiber and subsequently dip-coated with polydimethylsiloxane (PDMS). This formed a uniform nanofibrous absorbing mesh over the optical fiber end-face wherein the constituent MWCNTs were aligned preferentially along individual nanofibers. Infiltration of the PDMS through this nanofibrous mesh onto the underlying substrate was observed and the resulting composites exhibited high optical absorption (>97%). Thickness control from 2.3  μ m to 41.4  μ m was obtained by varying the electrospinning time. Under laser excitation with 11  μ J pulse energy, ultrasound pressures of 1.59 MPa were achieved at 1.5 mm from the coatings. On comparing the electrospun ultrasound transmitters with a dip-coated reference fabricated using the same constituent materials and possessing identical optical absorption, a five-fold increase in the generated pressure and wider bandwidth was observed. The electrospun transmitters exhibited high optical absorption, good elastomer infiltration, and ultrasound generation capability in the range of pressures used for clinical pulse-echo imaging. All-optical ultrasound probes with such transmitters fabricated by electrospinning could be well-suited for incorporation into catheters and needles for diagnostics and therapeutic applications.

  12. Hierarchically Structured Electrospun Fibers

    Directory of Open Access Journals (Sweden)

    Nicole E. Zander

    2013-01-01

    Full Text Available Traditional electrospun nanofibers have a myriad of applications ranging from scaffolds for tissue engineering to components of biosensors and energy harvesting devices. The generally smooth one-dimensional structure of the fibers has stood as a limitation to several interesting novel applications. Control of fiber diameter, porosity and collector geometry will be briefly discussed, as will more traditional methods for controlling fiber morphology and fiber mat architecture. The remainder of the review will focus on new techniques to prepare hierarchically structured fibers. Fibers with hierarchical primary structures—including helical, buckled, and beads-on-a-string fibers, as well as fibers with secondary structures, such as nanopores, nanopillars, nanorods, and internally structured fibers and their applications—will be discussed. These new materials with helical/buckled morphology are expected to possess unique optical and mechanical properties with possible applications for negative refractive index materials, highly stretchable/high-tensile-strength materials, and components in microelectromechanical devices. Core-shell type fibers enable a much wider variety of materials to be electrospun and are expected to be widely applied in the sensing, drug delivery/controlled release fields, and in the encapsulation of live cells for biological applications. Materials with a hierarchical secondary structure are expected to provide new superhydrophobic and self-cleaning materials.

  13. Recent Advances in Cell Electrospining of Natural and Synthetic Nanofibers for Regenerative Medicine.

    Science.gov (United States)

    Zamani, Reza; Aval, Sedigheh Fekri; Pilehvar-Soltanahmadi, Younes; Nejati-Koshki, Kazem; Zarghami, Nosratollah

    2018-01-22

    The progression of nanotechnology provides opportunities to manipulate synthetic and natural materials to mimic the natural structure for tissue engineering applications. The electrospinning technique applies electrostatic principle to fabricate electrospun nanofibers. Nanofiber scaffolds are precisely similar to the native extracellular matrix (ECM) and support cell proliferation, adhesion, tendency to preserve their phenotypic shape and directed growth according to the nanofiber direction. This study reviewed both the natural and synthetic type of nanofibers and described the different properties used to trigger certain process in the tissue development. Also, the potential applications of electrospun scaffolds for regenerative medicine were summarized. © Georg Thieme Verlag KG Stuttgart · New York.

  14. Cell proliferation on PVA/sodium alginate and PVA/poly(γ-glutamic acid) electrospun fiber.

    Science.gov (United States)

    Yang, Jen Ming; Yang, Jhe Hao; Tsou, Shu Chun; Ding, Chian Hua; Hsu, Chih Chin; Yang, Kai Chiang; Yang, Chun Chen; Chen, Ko Shao; Chen, Szi Wen; Wang, Jong Shyan

    2016-09-01

    To overcome the obstacles of easy dissolution of PVA nanofibers without crosslinking treatment and the poor electrospinnability of the PVA cross-linked nanofibers via electrospinning process, the PVA based electrospun hydrogel nanofibers are prepared with post-crosslinking method. To expect the electrospun hydrogel fibers might be a promising scaffold for cell culture and tissue engineering applications, the evaluation of cell proliferation on the post-crosslinking electrospun fibers is conducted in this study. At beginning, poly(vinyl alcohol) (PVA), PVA/sodium alginate (PVASA) and PVA/poly(γ-glutamic acid) (PVAPGA) electrospun fibers were prepared by electrospinning method. The electrospun PVA, PVASA and PVAPGA nanofibers were treated with post-cross-linking method with glutaraldehyde (Glu) as crosslinking agent. These electrospun fibers were characterized with thermogravimetry analysis (TGA) and their morphologies were observed with a scanning electron microscope (SEM). To support the evaluation and explanation of cell growth on the fiber, the study of 3T3 mouse fibroblast cell growth on the surface of pure PVA, SA, and PGA thin films is conducted. The proliferation of 3T3 on the electrospun fiber surface of PVA, PVASA, and PVAPGA was evaluated by seeding 3T3 fibroblast cells on these crosslinked electrospun fibers. The cell viability on electrospun fibers was conducted with water-soluble tetrazolium salt-1 assay (Cell Proliferation Reagent WST-1). The morphology of the cells on the fibers was also observed with SEM. The results of WST-1 assay revealed that 3T3 cells cultured on different electrospun fibers had similar viability, and the cell viability increased with time for all electrospun fibers. From the morphology of the cells on electrospun fibers, it is found that 3T3 cells attached on all electrospun fiber after 1day seeded. Cell-cell communication was noticed on day 3 for all electrospun fibers. Extracellular matrix (ECM) productions were found and

  15. Flexible phosphorus doped carbon nanosheets/nanofibers: Electrospun preparation and enhanced Li-storage properties as free-standing anodes for lithium ion batteries

    Science.gov (United States)

    Li, Desheng; Wang, Dongya; Rui, Kun; Ma, Zhongyuan; Xie, Ling; Liu, Jinhua; Zhang, Yu; Chen, Runfeng; Yan, Yan; Lin, Huijuan; Xie, Xiaoji; Zhu, Jixin; Huang, Wei

    2018-04-01

    The emerging wearable and foldable electronic devices drive the development of flexible lithium ion batteries (LIBs). Carbon materials are considered as one of the most promising electrode materials for LIBs due to their light weight, low cost and good structural stability against repeated deformations. However, the specific capacity, rate capability and long-term cycling performance still need to be improved for their applications in next-generation LIBs. Herein, we report a facile approach for immobilizing phosphorus into a large-area carbon nanosheets/nanofibers interwoven free-standing paper for LIBs. As an anode material for LIBs, it shows high reversible capacity of 1100 mAh g-1 at a current density of 200 mA g-1, excellent rate capabilities (e.g., 200 mAh g-1 at 20,000 mA g-1). Even at a high current density of 1000 mA g-1, it still maintains a superior specific capacity of 607 mAh g-1 without obvious decay.

  16. Electrospun polydimethylsiloxane/polyacrylonitrile/titanium dioxide nanofibers as a new coating for determination of alpha-linolenic acid in milk by direct immersion-solid phase nanoextraction.

    Science.gov (United States)

    Sadeghi, Sahar; Mollahosseini, Afsaneh

    2018-01-15

    In this study, polydimethylsiloxane/polyacrylonitrile/titanium dioxide (PDMS/PAN/TiO 2 ) nanofibers were synthesized via electrospinning method to extract and quantify alpha-linolenic acid (ALA, C18:3), as a model analyte, in milk by direct immersion-solid phase nanoextraction (DI-SPNE) with gas chromatography-flame ionization detector (GC-FID). The affecting factors on the electrospinning process such as, PDMS concentration, amount of TiO 2 nanoparticles (NPs), voltage, and electrospinning distance were optimized using Taguchi's orthogonal design. The SPNE experimental conditions such as, extraction time, agitation rate, pH and salt concentration, were also optimized using response surface methodology (RSM) based on a central composite design (CCD). Under optimized conditions, the resulting calibration curve was linear in the range of 1-4000ngmL -1 with R 2 =0.998. The intraday, interday, and fiber-to-fiber repeatability were calculated and the corresponding relative standard deviation was less than 9% in all the cases. The limit of detection and limit of quantification were found to be 0.2 and 0.6ngmL -1 , respectively. Omega-3 enriched milk was used as a real sample and the value of relative recoveries were measured to be in the range of 92-106%. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Performance of electrodes synthesized with polyacrylonitrile-based carbon nanofibers for application in electrochemical sensors and biosensors.

    Science.gov (United States)

    Adabi, Mahdi; Saber, Reza; Faridi-Majidi, Reza; Faridbod, Farnoush

    2015-03-01

    The purpose of this work was to investigate the performance of electrodes synthesized with Polyacrylonitrile-based carbon nanofibers (PAN-based CNFs). The homogenous PAN solutions with different concentrations were prepared and electrospun to acquire PAN nanofibers and then CNFs were fabricated by heat treatment. The effective parameters for the production of electrospun CNF electrode were investigated. Scanning electron microscopy (SEM) was used to characterize electrospun nanofibers. Cyclic voltammetry was applied to investigate the changes of behavior of electrospun CNF electrodes with different diameters. The structure of CNFs was also evaluated via X-ray diffraction (XRD) and Raman spectroscopy. The results exhibited that diameter of nanofibers reduced with decreasing polymer concentration and applied voltage and increasing tip-to-collector distance, while feeding rate did not have significant effect on nanofiber diameter. The investigations of electrochemical behavior also demonstrated that cyclic voltammetric response improved as diameter of CNFs electrode decreased. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Electrospun Polymer-Fiber Solar Cell

    Directory of Open Access Journals (Sweden)

    Shinobu Nagata

    2013-01-01

    Full Text Available A novel electrospun polymer-fiber solar cell was synthesized by electrospinning a 1 : 2.5 weight% ratio mixture of poly[2-methoxy-5-(2-ethylhexyloxy-1,4-phenylenevinylene] (MEH-PPV and [6,6]-phenyl C61 butyric acid methyl ester (PCBM resulting in bulk heterojunctions. Electrospinning is introduced as a technique that may increase polymer solar cell efficiency, and a list of advantages of the technique applied to solar cells is discussed. The device achieved a power conversion efficiency of %. The absorption and photoluminescence of MEH-PPV nanofibers are compared to thin films of the same material. Electrospun nanofibers are discussed as a favorable structure for application in polymer solar cells.

  19. Electrospinning chitosan/poly(ethylene oxide) solutions with essential oils: Correlating solution rheology to nanofiber formation.

    Science.gov (United States)

    Rieger, Katrina A; Birch, Nathan P; Schiffman, Jessica D

    2016-03-30

    Electrospinning hydrophilic nanofiber mats that deliver hydrophobic agents would enable the development of new therapeutic wound dressings. However, the correlation between precursor solution properties and nanofiber morphology for polymer solutions electrospun with or without hydrophobic oils has not yet been demonstrated. Here, cinnamaldehyde (CIN) and hydrocinnamic alcohol (H-CIN) were electrospun in chitosan (CS)/poly(ethylene oxide) (PEO) nanofiber mats as a function of CS molecular weight and degree of acetylation (DA). Viscosity stress sweeps determined how the oils affected solution viscosity and chain entanglement (Ce) concentration. Experimentally, the maximum polymer:oil mass ratio electrospun was 1:3 and 1:6 for CS/PEO:CIN and:H-CIN, respectively; a higher chitosan DA increased the incorporation of H-CIN only. The correlations determined for electrospinning plant-derived oils could potentially be applied to other hydrophobic molecules, thus broadening the delivery of therapeutics from electrospun nanofiber mats. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Nanobiotechnology approach to fabricate polycaprolactone nanofibers containing solid titanium nanoparticles as future implant materials

    DEFF Research Database (Denmark)

    Sheikh, Faheem A.; Kanjwal, Muzafar Ahmed; Cha, Jaegwan

    2011-01-01

    In this study, a good combination of electrospun poly(caprolactone) nanofibers incorporated with high purity titanium nanoparticles is introduced for hard tissue engineering applications. A simple approach to utilize the colloidal properties of poly(caprolactone) and titanium nanoparticles...

  1. Recent trends in electrospinning of polymer nanofibers and their applications in ultra thin layer chromatography.

    Science.gov (United States)

    Moheman, Abdul; Alam, Mohammad Sarwar; Mohammad, Ali

    2016-03-01

    Fabrication of polymer derived electrospun nanofibers by electrospinning as chromatographic sorbent bed for ultra-thin layer chromatography (UTLC) is a very demanding topic in analytical chemistry. This review presents an overview of recent development in the fabrication of polymer derived electrospun nanofibers and their applications to design UTLC plates as stationary phases for on-plate identification and separation of analytes from their mixture solutions. It has been reported that electrospun fiber based stationary phases in UTLC have enhanced separation efficiency to provide separation of analyte mixture in a shorter development time than those of traditional particle-based TLC stationary phases. In addition, electrospun UTLC is cost effective and can be modified for obtaining different surface selectivities by changing the polymer materials to electrospun devices. Electrospun UTLC plates are not available commercially till date and efforts are being rendered for their commercialization. The morphology and diameter of electrospun nanofibers are highly dependent on several parameters such as type of polymer, polymer molecular weight, solvent, viscosity, conductivity, surface tension, applied voltage, collector distance and flow rate of the polymer solution during electrospinning process. Among the aforementioned parameters, solution viscosity is an important parameter which is mainly influenced by polymer concentration. This review provides evidence for the fabrication of UTLC plates containing electrospun polymer nanofibers. Furthermore, the future prospects related to electrospinning and its application in obtaining of different types of electrospun nanofibers are discussed. The present communication is aimed to review the work which appeared during 2009-2014 on the application of polymer derived electrospun nanofibers in ultra thin layer chromatography. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. Fabrication of nanofiber mats from electrospinning of functionalized polymers

    International Nuclear Information System (INIS)

    Oktay, Burcu; Kayaman-Apohan, Nilhan; Erdem-Kuruca, Serap

    2014-01-01

    Electrospinning technique enabled us to prepare nanofibers from synthetic and natural polymers. In this study, it was aimed to fabricate electrospun poly(vinyl alcohol) (PVA) based nanofibers by reactive electrospinning process. To improve endurance of fiber toward to many solvents, PVA was functionalized with photo-crosslinkable groups before spinning. Afterward PVA was crosslinked by UV radiation during electrospinning process. The nanofiber mats were characterized by scanning electron microscopy (SEM). The results showed that homogenous, uniform and crosslinked PVA nanofibers in diameters of about 200 nm were obtained. Thermal stability of the nanofiber mat was investigated with thermal gravimetric analysis (TGA). Also the potential use of this nanofiber mats for tissue engineering was examined. Osteosarcoma (Saos) cells were cultured on the nanofiber mats

  3. Synthesis of Antibacterial Silver–Poly(ɛ-caprolactone-Methacrylic Acid Graft Copolymer Nanofibers and Their Evaluation as Potential Wound Dressing

    Directory of Open Access Journals (Sweden)

    Mohammed A. Al-Omair

    2015-08-01

    Full Text Available Electrospun polycaprolacyone/polymethacrylic acid graft copolymer nanofibers (PCL/MAA containing silver nanoparticles (AgNPs were synthesized for effective wound disinfection. Surface morphology, AgNPs content, water uptake of electrospun PCL/MAA graft copolymer nanofibers without and with AgNPs, and levels of AgNPs leaching from the nanofibers in water as well as antimicrobial efficacy were studied. Scanning electron microscope images revealed that AgNPs dispersed well in PCL/MAA copolymer nanofibers with mean fiber diameters in the range of 200–579 nm and the fiber uniformity and diameter were not affected by the AgNPs. TEM images showed that AgNPs are present in/on the electrospun PCL/MAA graft copolymer nanofibers. The diameter of the electrospun nanofibers containing AgNPs was in the range of 200–579 nm, however, the diameter of AgNPs was within the range of 20–50 nm and AgNPs were observed to be spherical in shape. The PCL/MAA copolymer nanofibers showed a good hydrophilic property and the nanofibers containing AgNPs had excellent antimicrobial activity against the Gram-negative bacteria Escherichia coli and Pseudomonas aeruginosa, and against the Gram-positive bacteria Bacillus thuringiensis and Staphylococcus aureus, with a clear inhibition zone with a diameter between 22 and 53 mm. Moreover, electrospun PCL/MAA copolymer nanofibers sustained the release of AgNPs into water over 72 h.

  4. Preparation and characterization of electrospun poly(phthalazinone ether nitrile ketone) membrane with novel thermally stable properties

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Gang; Zhang, Hao; Qian, Bingqing [Carbon Research Laboratory, Liaoning Key Lab for Energy Materials and Chemical Engineering, State Key Lab of Fine Chemicals, Dalian University of Technology, Dalian 116024 (China); Wang, Jinyan, E-mail: wangjinyan@dlut.edu.cn [Department of Polymer Science and Materials, Dalian University of Technology, Dalian 116024 (China); Jian, Xigao [Department of Polymer Science and Materials, Dalian University of Technology, Dalian 116024 (China); Qiu, Jieshan, E-mail: jqiu@dlut.edu.cn [Carbon Research Laboratory, Liaoning Key Lab for Energy Materials and Chemical Engineering, State Key Lab of Fine Chemicals, Dalian University of Technology, Dalian 116024 (China)

    2015-10-01

    Highlights: • Poly (phthalazinone ether nitrile ketone) (PPENK) was used to successfully prepare nanofiber membranes by electrospinning. • Electrospun membrane exhibits a good thermostability. • Electrospun membrane. - Abstract: Electrospun nanofibrous membranes have several applications because of their excellent properties, such as high porosity, small fiber diameter, and large surface area. However, high-temperature resistant electrospun membranes remain a challenge because of the absence of precursors that offer spinnability, scalability, and superior thermal stability. In this study, poly(phthalazinone ether nitrile ketone) (PPENK) was used to successfully prepare nanofiber membranes by electrospinning. Electrospun PPENK membranes were characterized by scanning electron microscopy, differential scanning calorimetry, Fourier transform infrared spectroscopy, and tensile stress–strain tests. Results indicated that the prepared electrospun membranes had a very high glass transition temperature, superior chemical resistance, and excellent mechanical strength. These desirable properties broaden their potential application in membranes and treatment of various hot fluid streams without strict temperature control.

  5. Synthesis, characterization and photocatalytic performance of SnS nanofibers and SnSe nanofibers derived from the electrospinning-made SnO{sub 2} nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Li; Li, Dan; Dong, Xiangting; Ma, Qianli; Yu, Wensheng; Wang, Xinlu; Yu, Hui; Wang, Jinxian; Liu, Guixia, E-mail: dongxiangting888@163.com [Key Laboratory of Applied Chemistry and Nanotechnology at Universities of Jilin Province, Changchun University of Science and Technology, Changchun (China)

    2017-11-15

    SnO{sub 2} nanofibers were fabricated by calcination of the electrospun PVP/SnCl{sub 4} composite nanofibers. For the first time, SnS nanofibers and SnSe nanofibers were successfully synthesized by double crucible sulfurization and selenidation methods via inheriting the morphology of SnO{sub 2} nanofibers used as precursors, respectively. X-ray diffraction (XRD) analysis shows SnS nanofibers and SnSe nanofibers are respectively pure orthorhombic phase with space group of Pbnm and Cmcm. Scanning electron microscope (SEM) observation indicates that the diameters of SnS nanofibers and SnSe nanofibers are respectively 140.54±12.80 nm and 96.52±14.17 nm under the 95 % confidence level. The photocatalytic activities of samples were studied by using rhodamine B (Rh B) as degradation agent. When SnS or SnSe nanofibers are employed as the photocatalysts, the respective degradation rates of Rh B solution under the ultraviolet light irradiation after 200 min irradiation are 92.55 % and 92.86 %. The photocatalytic mechanism and formation process of SnS and SnSe nanofibers are also provided. More importantly, this preparation technique is of universal significance to prepare other metal chalcogenides nanofibers. (author)

  6. The synthesis of titanium carbide-reinforced carbon nanofibers

    Science.gov (United States)

    Zhu, Pinwen; Hong, Youliang; Liu, Bingbing; Zou, Guangtian

    2009-06-01

    Tailoring hard materials into nanoscale building blocks can greatly extend the applications of hard materials and, at the same time, also represents a significant challenge in the field of nanoscale science. This work reports a novel process for the preparation of carbon-based one-dimensional hard nanomaterials. The titanium carbide-carbon composite nanofibers with an average diameter of 90 nm are prepared by an electrospinning technique and a high temperature pyrolysis process. A composite solution containing polyacrylonitrile and titanium sources is first electrospun into the composite nanofibers, which are subsequently pyrolyzed to produce the desired products. The x-ray diffraction pattern and transmission electron microscopy results show that the main phase of the as-synthesized nanofibers is titanium carbide. The Raman analyses show that the composite nanofibers have low graphite clusters in comparison with the pure carbon nanofibers originating from the electrospun polyacrylonitrile nanofibers. The mechanical property tests demonstrate that the titanium carbide-carbon nanofiber membranes have four times higher tensile strength than the carbon nanofiber membranes, and the Young's modulus of the titanium carbide-carbon nanofiber membranes increases in direct proportion to the titanium quantity.

  7. Nanostructured Electrospun Hybrid Graphene/Polyacrylonitrile Yarns

    Science.gov (United States)

    Razal, Joselito M.; Naebe, Minoo

    2017-01-01

    Novel nanostructured hybrid electrospun polyacrylonitrile (PAN) yarns with different graphene ratios were prepared using liquid crystal graphene oxide (LCGO) and PAN. It was found that the well-dispersed LCGO were oriented along the fiber axis in an electrified thin liquid jet during electrospinning. The graphene oxide sheets were well dispersed in the polar organic solvent, forming nematic liquid crystals upon increasing concentration. Twisted nanofibers were produced from aligned nanofibrous mats prepared by conventional electrospinning. It was found that the mechanical properties of the twisted nanofiber yarns increased even at very low LCGO loading. This research offers a new approach for the fabrication of continuous, strong, and uniform twisted nanofibers which could show promise in developing a novel carbon fiber precursor. PMID:28946668

  8. Nanostructured Electrospun Hybrid Graphene/Polyacrylonitrile Yarns.

    Science.gov (United States)

    Mehrpouya, Fahimeh; Foroughi, Javad; Naficy, Sina; Razal, Joselito M; Naebe, Minoo

    2017-09-25

    Novel nanostructured hybrid electrospun polyacrylonitrile (PAN) yarns with different graphene ratios were prepared using liquid crystal graphene oxide (LCGO) and PAN. It was found that the well-dispersed LCGO were oriented along the fiber axis in an electrified thin liquid jet during electrospinning. The graphene oxide sheets were well dispersed in the polar organic solvent, forming nematic liquid crystals upon increasing concentration. Twisted nanofibers were produced from aligned nanofibrous mats prepared by conventional electrospinning. It was found that the mechanical properties of the twisted nanofiber yarns increased even at very low LCGO loading. This research offers a new approach for the fabrication of continuous, strong, and uniform twisted nanofibers which could show promise in developing a novel carbon fiber precursor.

  9. Polyacrylonitrile (PAN)/crown ether composite nanofibers for the selective adsorption of cations

    NARCIS (Netherlands)

    Tas, Sinem; Kaynan, Ozge; Ozden-Yenigun, Elif; Nijmeijer, Dorothea C.

    2016-01-01

    In this study, we prepared electrospun polyacrylonitrile (PAN) nanofibers functionalized with dibenzo-18-crown-6 (DB18C6) crown ether and showed the potential of these fibers for the selective recovery of K+ from other both mono- and divalent ions in aqueous solutions. Nanofibers were characterized

  10. Performance of electrodes synthesized with polyacrylonitrile-based carbon nanofibers for application in electrochemical sensors and biosensors

    International Nuclear Information System (INIS)

    Adabi, Mahdi; Saber, Reza; Faridi-Majidi, Reza; Faridbod, Farnoush

    2015-01-01

    The purpose of this work was to investigate the performance of electrodes synthesized with Polyacrylonitrile-based carbon nanofibers (PAN-based CNFs). The homogenous PAN solutions with different concentrations were prepared and electrospun to acquire PAN nanofibers and then CNFs were fabricated by heat treatment. The effective parameters for the production of electrospun CNF electrode were investigated. Scanning electron microscopy (SEM) was used to characterize electrospun nanofibers. Cyclic voltammetry was applied to investigate the changes of behavior of electrospun CNF electrodes with different diameters. The structure of CNFs was also evaluated via X-ray diffraction (XRD) and Raman spectroscopy. The results exhibited that diameter of nanofibers reduced with decreasing polymer concentration and applied voltage and increasing tip-to-collector distance, while feeding rate did not have significant effect on nanofiber diameter. The investigations of electrochemical behavior also demonstrated that cyclic voltammetric response improved as diameter of CNFs electrode decreased. - Highlights: • Electrospun CNFs can be directly used as working electrode. • Cyclic voltammetric response improved as diameter of CNFs electrode decreased. • The diameter of nanofibers reduced with decreasing polymer concentration. • The diameter of nanofibers reduced with decreasing applied voltage. • The diameter of nanofibers reduced with increasing tip-to-collector distance

  11. Increasing Mechanical Properties of 2-D-Structured Electrospun Nylon 6 Non-Woven Fiber Mats

    Science.gov (United States)

    Xiang, Chunhui; Frey, Margaret W.

    2016-01-01

    Tensile strength, Young’s modulus, and toughness of electrospun nylon 6 non-woven fiber mats were improved by increasing individual nanofiber strength and fiber–fiber load sharing. Single-walled carbon nanotubes (CNTs) were used as reinforcement to increase the strength of the electrospun nylon 6 nanofibers. Young’s modulus, tensile strength, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % solutions increased 51%, 87%, and 136%, respectively, after incorporating 1 wt % CNTs into the nylon 6 nanofibers. Three methods were investigated to enhance fiber–fiber load sharing: increasing friction between fibers, thermal bonding, and solvent bonding. The addition of beaded nylon 6 nanofibers into the non-woven fiber mats to increase fiber-fiber friction resulted in a statistically significantly increase in Young’s modulus over comparable smooth non-woven fiber mats. After annealing, tensile strength, elongation, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % + 10 wt % solutions increased 26%, 28%, and 68% compared to those from 20 wt % solutions. Solvent bonding with formic acid vapor at room temperature for 30 min caused increases of 56%, 67%, and 39% in the Young’s modulus, tensile strength, and toughness of non-woven fiber mats, respectively. The increases attributed to increased individual nanofiber strength and solvent bonding synergistically resulted in the improvement of Young’s modulus of the electrospun nylon 6 non-woven fiber mats. PMID:28773397

  12. Increasing Mechanical Properties of 2-D-Structured Electrospun Nylon 6 Non-Woven Fiber Mats

    Directory of Open Access Journals (Sweden)

    Chunhui Xiang

    2016-04-01

    Full Text Available Tensile strength, Young’s modulus, and toughness of electrospun nylon 6 non-woven fiber mats were improved by increasing individual nanofiber strength and fiber–fiber load sharing. Single-walled carbon nanotubes (CNTs were used as reinforcement to increase the strength of the electrospun nylon 6 nanofibers. Young’s modulus, tensile strength, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % solutions increased 51%, 87%, and 136%, respectively, after incorporating 1 wt % CNTs into the nylon 6 nanofibers. Three methods were investigated to enhance fiber–fiber load sharing: increasing friction between fibers, thermal bonding, and solvent bonding. The addition of beaded nylon 6 nanofibers into the non-woven fiber mats to increase fiber-fiber friction resulted in a statistically significantly increase in Young’s modulus over comparable smooth non-woven fiber mats. After annealing, tensile strength, elongation, and toughness of the nylon 6 non-woven fiber mats electrospun from 20 wt % + 10 wt % solutions increased 26%, 28%, and 68% compared to those from 20 wt % solutions. Solvent bonding with formic acid vapor at room temperature for 30 min caused increases of 56%, 67%, and 39% in the Young’s modulus, tensile strength, and toughness of non-woven fiber mats, respectively. The increases attributed to increased individual nanofiber strength and solvent bonding synergistically resulted in the improvement of Young’s modulus of the electrospun nylon 6 non-woven fiber mats.

  13. Multifunctional electroactive electrospun nanofiber structures from water solution blends of PVA/ODA-MMT and poly(maleic acid-alt-acrylic acid): effects of Ag, organoclay, structural rearrangement and NaOH doping factors

    Science.gov (United States)

    Şimşek, Murat; Rzayev, Zakir M. O.; Bunyatova, Ulviya

    2016-06-01

    Novel multifunctional colloidal polymer nanofiber electrolytes were fabricated by green reactive electrospinning nanotechnology from various water solution/dispersed blends of poly (vinyl alcohol-co-vinyl acetate) (PVA)/octadecyl amine-montmorillonite (ODA-MMT) as matrix polymer nanocomposite and poly(maleic acid-alt-acrylic acid) (poly(MAc-alt-AA) and/or its Ag-carrying complex as partner copolymers. Polymer nanofiber electrolytes were characterized using FTIR, XRD, thermal (DSC, TGA-DTG), SEM, and electrical analysis methods. Effects of partner copolymers, organoclay, in situ generated silver nanoparticles (AgNPs), and annealing procedure on physical and chemical properties of polymer composite nanofibers were investigated. The electrical properties (resistance, conductivity, activation energy) of nanofibers with/without NaOH doping agent were also evaluated. This work presented a structural rearrangement of nanofiber mats by annealing via decarboxylation of anhydride units with the formation of new conjugated double bond sites onto partner copolymer main chains. It was also found that the semiconductor behaviors of nanofiber structures were essentially improved with increasing temperature and fraction of partner copolymers as well as presence of organoclay and AgNPs in nanofiber composite.

  14. Electrocatalytic properties of Pt/carbon composite nanofibers

    International Nuclear Information System (INIS)

    Lin Zhan; Ji Liwen; Zhang Xiangwu

    2009-01-01

    Pt/carbon composite nanofibers were prepared by electrodepositing Pt nanoparticles directly onto electrospun carbon nanofibers. The morphology and size of Pt nanoparticles were controlled by the electrodeposition time. The resulting Pt/carbon composite nanofibers were characterized by running cyclic voltammograms in 0.20 M H 2 SO 4 and 5.0 mM K 4 [Fe(CN) 6 ] + 0.10 M KCl solutions. The electrocatalytic activities of Pt/carbon composite nanofibers were measured by the oxidation of methanol. Results show that Pt/carbon composite nanofibers possess the properties of high active surface area and fast electron transfer rate, which lead to a good performance towards the electrocatalytic oxidation of methanol. It is also found that the Pt/carbon nanofiber electrode with a Pt loading of 0.170 mg cm -2 has the highest activity.

  15. Development and characterization of highly oriented PAN nanofiber

    Directory of Open Access Journals (Sweden)

    M. Sadrjahani

    2010-12-01

    Full Text Available A simple and non-conventional electrospinning technique was employed for producing highly oriented Polyacrylonitrile (PAN nanofibers. The PAN nanofibers were electrospun from 14 wt% solution of PAN in dimethylformamid (DMF at 11 kv on a rotating drum with various linear speeds from 22.5 m/min to 67.7 m/min. The influence of take up velocity was investigated on the degree of alignment, internal structure and mechanical properties of collected PAN nanofibers. Using an image processing technique, the best degree of alignment was obtained for those nanofibers collected at a take up velocity of 59.5 m/min. Moreover, Raman spectroscopy was used for measuring molecular orientation of PAN nanofibers. Similarly, a maximum chain orientation parameter of 0.25 was determined for nanofibers collected at a take up velocity of 59.5 m/min.

  16. Electrospinning of polymeric nanofibers for drug delivery applications.

    Science.gov (United States)

    Hu, Xiuli; Liu, Shi; Zhou, Guangyuan; Huang, Yubin; Xie, Zhigang; Jing, Xiabin

    2014-07-10

    Electrospinning has been recognized as a simple and versatile method for fabrication of polymer nanofibers. Various polymers that include synthetic, natural, and hybrid materials have been successfully electrospun into ultrafine fibers. The inherently high surface to volume ratio of electrospun fibers can enhance cell attachment, drug loading, and mass transfer properties. Drugs ranging from antibiotics and anticancer agents to proteins, DNA, RNA, living cells, and various growth factors have been incorporated into electrospun fibers. This article presents an overview of electrospinning techniques and their application in drug delivery. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Effect of Voltage and Flow Rate Electrospinning Parameters on Polyacrylonitrile Electrospun Fibers

    Science.gov (United States)

    Bakar, S. S. S.; Fong, K. C.; Eleyas, A.; Nazeri, M. F. M.

    2018-03-01

    Currently, electrospinning is a very famous technique and widely used for forming polymer nanofibers. In this paper, the Polyacrylonitrile (PAN) nanofibers were prepared in concentration of 10wt% with varied processing parameters that can affect the properties of PAN fiber in term of fiber diameter and electrical conductivity was presented. Voltage of 10, 15 and 20 kV with PAN flow rate of 1 electrospun PAN fibers were then undergo pyrolysis at 800°C for 30 minutes. The resultant PAN nanofibers were then analysed by SEM, XRD and four point probe test after pyrolysis process. SEM image show continuos uniform and smooth surface fibrous structure of electrospun PAN fibers with average diameter of 1.81 μm. The fiber morphology is controlled by manipulating the processing parameters of electrospinning process. The results showed that the resistance of electrospun PAN fibers decreases as the processing parameter changes by increasing the applied voltage and flow rate of electrospinning.

  18. Polyamic Acid Nanofibers Produced by Needleless Electrospinning

    Directory of Open Access Journals (Sweden)

    Oldrich Jirsak

    2010-01-01

    Full Text Available The polyimide precursor (polyamic acid produced of 4,4′-oxydiphthalic anhydride and 4,4′-oxydianiline was electrospun using needleless electrospinning method. Nonwoven layers consisting of submicron fibers with diameters in the range about 143–470 nm on the polypropylene spunbond supporting web were produced. Filtration properties of these nanofiber layers on the highly permeable polypropylene support—namely filtration effectivity and pressure drop—were evaluated. Consequently, these polyamic acid fibers were heated to receive polyimide nanofibers. The imidization process has been studied using IR spectroscopy. Some comparisons with the chemically identical polyimide prepared as the film were made.

  19. Nanocomposite Electrospun Nanofiber Membranes for Environmental Remediation

    Directory of Open Access Journals (Sweden)

    Shahin Homaeigohar

    2014-02-01

    Full Text Available Rapid worldwide industrialization and population growth is going to lead to an extensive environmental pollution. Therefore, so many people are currently suffering from the water shortage induced by the respective pollution, as well as poor air quality and a huge fund is wasted in the world each year due to the relevant problems. Environmental remediation necessitates implementation of novel materials and technologies, which are cost and energy efficient. Nanomaterials, with their unique chemical and physical properties, are an optimum solution. Accordingly, there is a strong motivation in seeking nano-based approaches for alleviation of environmental problems in an energy efficient, thereby, inexpensive manner. Thanks to a high porosity and surface area presenting an extraordinary permeability (thereby an energy efficiency and selectivity, respectively, nanofibrous membranes are a desirable candidate. Their functionality and applicability is even promoted when adopting a nanocomposite strategy. In this case, specific nanofillers, such as metal oxides, carbon nanotubes, precious metals, and smart biological agents, are incorporated either during electrospinning or in the post-processing. Moreover, to meet operational requirements, e.g., to enhance mechanical stability, decrease of pressure drop, etc., nanofibrous membranes are backed by a microfibrous non-woven forming a hybrid membrane. The novel generation of nanocomposite/hybrid nanofibrous membranes can perform extraordinarily well in environmental remediation and control. This reality justifies authoring of this review paper.

  20. Enhanced cell mitochondrial activity using electrospun nanofibers

    CSIR Research Space (South Africa)

    Jacobs, V

    2015-06-01

    Full Text Available technology and surgical applications. Proc Instn Mech Eng Part H - J Eng Med. 1998; 212: 101-111. 16. Barbanti, S.H.; Zavaglia, C.A.C. & Duek, E.A.R. Polímeros bioreabsorvíveis na engenharia de tecidos. Polímeros: Ciência e Tecnologia. 2005; 15: 13-21. 17...

  1. Preparation and characterization of CS/ PEO/ cefazolin nanofibers with in vitro and in vivo testing

    Directory of Open Access Journals (Sweden)

    Minoo Sadri

    2017-04-01

    Full Text Available Objective(S: Electrospinning of chitosan/polyethylene oxide (CS/PEO nanofibers with the addition of cefazolin to create nanofibers with antimicrobial properties were examined. Methods: Polymeric nanofibers including CS/PEO and CS/PEO /cefazolin, were produced by electrospinning method. The range of nanofiber was 60-100 nm in diameter and measured with ImageJ software. The morphology of electrospun nanofibers was studied with use of scanning electron microscopy (SEM. Moreover, the chemical structures of the nanofibers were evaluated by FT-IR. The drug release of nanofibers was also investigated by UV-Vis spectrophotometry. The antibacterial activity of scaffolds was tested by two type bacteria including Escherichia coli and Staphylococcus aureus. The healing ability of nanofibers was studied on the rat’s wound. Results: The SEM images indicated that the addition of cefazolin as much as 1wt% brings about the best nanofiber. Also, the morphology of electrospun nanofiber is dependent on the viscosity of the solution and the ratio of CS /PEO/cefazolin. According to the results of cefazolin releasing from nanofibers, the best results were obtained in the presence of CS /PEO/1wt%cefazolin nanofibers as healing sample. In animal studies, the effect of nanofibers was studied in the burn wound healing of rats and improvement of the wound was observed by nanofibers containing 1%wt cefazolin. Conclusions: According to these results, it seems that CS /PEO/1wt% cefazolin nanofiber is a good choice as a wound covering agent and hold more moisture in its structure thus the surface of wound remain wet during the healing process that prevent from nanofiber sticking to the wound surface.

  2. Electrospun Superhydrophobic Self-Cleaning Materials

    Science.gov (United States)

    Zhao, Yong; Wang, Nü

    In this chapter, we introduce the wettability of electrospinning products. Especially, we concentrate on the fabrication, characteristics, and applications of the electrospun self-cleaning materials. Self-cleaning materials are typical nature-inspired artificial materials learning from such as lotus leaf and many other plants or animals. Self-cleaning materials usually rely on a superhydrophobic surface, which should be of low surface free energy as well as large surface roughness. Electrospinning method is such a method that could facilely shape various hydrophobic polymers into ultrathin fibers with tunable surface microstructures. It means the electrospun products are of very large specific area, which satisfy the two basic conditions in preparing superhydrophobic surfaces. Therefore, in the last decade, scientists put forward a good few of elegant approaches to fabricate superhydrophobic materials by electrospinning. These methods can be generally classified into two routes. One is a direct route that creates superhydrophobic electrospun films from hydrophobic materials. Another is an indirect route that decorates electrospun nanofibers (no matter hydrophobic or hydrophilic) with hydrophobic chemicals. We first introduce some representative works on the fabrication of superhydrophobic self-cleaning materials by electrospinning method. Then we show some applications of these superhydrophobic materials. Finally, we give a brief personal perspective on this area.

  3. Multifunctional Composite Nanofibers for Smart Structures

    Science.gov (United States)

    2011-10-13

    translated to the composite nanofibrous structures in the form of nonwovens and yarns? (3) Can these functional composite fibers be integrated into...nanoparticles were co- electrospun into nonwoven mat and over meter long yarn. The SEM and TEM image in Report Documentation Page Form ApprovedOMB No...functional composite nanofiber structures (yarn and nonwoven ) characterized we explored the feasibility of integrating these functional composite fibers into

  4. Electrospun composites of PHBV/pearl powder for bone repairing

    Directory of Open Access Journals (Sweden)

    Jingjing Bai

    2015-08-01

    Full Text Available Electrospun fiber has highly structural similarity with natural bone extracelluar matrix (ECM. Many researches about fabricating organic–inorganic composite materials have been carried out in order to mimic the natural composition of bone and enhance the biocompatibility of materials. In this work, pearl powder was added to the poly (3-hydroxybutyrate-co-3-hydroxyvalerate (PHBV and the composite nanofiber scaffold was prepared by electrospinning. Mineralization ability of the composite scaffolds can be evaluated by analyzing hydroxyapatite (HA formation on the surface of nanofiber scaffolds. The obtained composite nanofiber scaffolds showed an enhanced mineralization capacity due to incorporation of pearl powder. The HA formed amount of the composite scaffolds was raised as the increase of pearl powder in composite scaffolds. Therefore, the prepared PHBV/pearl composite nanofiber scaffolds would be a promising candidate as an osteoconductive composite material for bone repairing.

  5. Nanofiber membrane-electrode-assembly and method of fabricating same

    Science.gov (United States)

    Pintauro, Peter N.; Ballengee, Jason; Brodt, Matthew

    2016-02-02

    In one aspect of the present invention, a fuel cell membrane-electrode-assembly (MEA) has an anode electrode, a cathode electrode, and a membrane disposed between the anode electrode and the cathode electrode. At least one of the anode electrode, the cathode electrode and the membrane is formed of electrospun nanofibers.

  6. Electrospun Nanofibrous Materials for Neural Tissue Engineering

    Directory of Open Access Journals (Sweden)

    Yee-Shuan Lee

    2011-02-01

    Full Text Available The use of biomaterials processed by the electrospinning technique has gained considerable interest for neural tissue engineering applications. The tissue engineering strategy is to facilitate the regrowth of nerves by combining an appropriate cell type with the electrospun scaffold. Electrospinning can generate fibrous meshes having fiber diameter dimensions at the nanoscale and these fibers can be nonwoven or oriented to facilitate neurite extension via contact guidance. This article reviews studies evaluating the effect of the scaffold’s architectural features such as fiber diameter and orientation on neural cell function and neurite extension. Electrospun meshes made of natural polymers, proteins and compositions having electrical activity in order to enhance neural cell function are also discussed.

  7. Electrospun polyimide-composite separator for lithium-ion batteries

    International Nuclear Information System (INIS)

    Shayapat, Jaritphun; Chung, Ok Hee; Park, Jun Seo

    2015-01-01

    Non-woven mats of thermally stable polyimide (PI) composites were fabricated as a separator of lithium-ion batteries (LIBs) by first electrospinning a mixture of the pre-polymer, poly(amic acid) ammonium salt (PAAS), and inorganic nanoparticles of SiO 2 or Al 2 O 3 and then imidizing the electrospun nanofibers of the PAAS composites at 350 °C. The microstructures of the electrospun PI nanofibers, electrospun PI–SiO 2 -composite nanofibers, electrospun PI–Al 2 O 3 -composite nanofibers, and the commercial separator SV718 were examined using field-emission scanning electron microscopy and transmission electron microscopy. Test results of the thermal properties of the PI nanofibers, PI-composite nanofibers, and SV718, obtained with a thermal gravimetric analyzer and a differential scanning calorimeter, indicate the superior thermal stability of PI and PI composites, which showed no melting peak and no decomposition at 600 °C, while SV718 had a melting peak at 137 °C and decomposed at 300 °C. The thermal stability of the separators, evaluated in a hot-oven test, showed no shrinkage of PI and PI composites at 200 °C, while SV718 started to shrink at above 100 °C. Using a drop of liquid electrolyte on the surface of each separator, the electrolyte contact angle on PI and PI composites was around 10° and that on SV718 was 54°, indicating that PI and PI composites had better wettability than SV718. The porosity and liquid-electrolyte uptake of the PI composites were over 90% and 790%, respectively, while the corresponding values for SV718 were 40% and 101%, respectively, implying that the separators consisting of the non-woven mats of PI–SiO 2 -composite nanofibers and PI–Al 2 O 3 -composite nanofibers had lower interfacial resistance than the commercial SV718 separator. The electrochemical performance of the PI-composite separator assembled between the LiCoO 2 cathode and the Li anode of an LIB exhibited more stable cycle performance, higher discharge

  8. Incorporation of functionalized gold nanoparticles into nanofibers for enhanced attachment and differentiation of mammalian cells

    Science.gov (United States)

    2012-01-01

    Background Electrospun nanofibers have been widely used as substrata for mammalian cell culture owing to their structural similarity to natural extracellular matrices. Structurally consistent electrospun nanofibers can be produced with synthetic polymers but require chemical modification to graft cell-adhesive molecules to make the nanofibers functional. Development of a facile method of grafting functional molecules on the nanofibers will contribute to the production of diverse cell type-specific nanofiber substrata. Results Small molecules, peptides, and functionalized gold nanoparticles were successfully incorporated with polymethylglutarimide (PMGI) nanofibers through electrospinning. The PMGI nanofibers functionalized by the grafted AuNPs, which were labeled with cell-adhesive peptides, enhanced HeLa cell attachment and potentiated cardiomyocyte differentiation of human pluripotent stem cells. Conclusions PMGI nanofibers can be functionalized simply by co-electrospinning with the grafting materials. In addition, grafting functionalized AuNPs enable high-density localization of the cell-adhesive peptides on the nanofiber. The results of the present study suggest that more cell type-specific synthetic substrata can be fabricated with molecule-doped nanofibers, in which diverse functional molecules are grafted alone or in combination with other molecules at different concentrations. PMID:22686683

  9. Formation of high aspect ratio polyamide-6 nanofibers via electrically induced double layer during electrospinning

    International Nuclear Information System (INIS)

    Nirmala, R.; Nam, Ki Taek; Park, Soo-Jin; Shin, Yu-Shik; Navamathavan, R.; Kim, Hak Yong

    2010-01-01

    In the present study, the formation of high aspect ratio nanofibers in polyamide-6 was investigated as a function of applied voltage ranging from 15 to 25 kV using electrospinning technique. All other experimental parameters were kept constant. The electrospun polyamide-6 nanofibers were characterized by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) and matrix-assisted laser desorption ionization time-of-flight (MALDI-TOF). FE-SEM images of polyamide-6 nanofibers showed that the diameter of the electrospun fiber was decreased with increasing applied voltage. At the critical applied voltage, the polymer solution was completely ionized to form the dense high aspect ratio nanofibers in between the main nanofibers. The diameter of the polyamide-6 nanofibers was observed to be in the range of 75-110 nm, whereas the high aspect ratio structures consisted of regularly distributed very fine nanofibers with diameters of about 9-28 nm. Trends in fiber diameter and diameter distribution were discussed for the high aspect ratio nanofibers. TEM results revealed that the formation of double layers in polyamide-6 nanofibers and then split-up into ultrafine fibers. The electrically induced double layer in combination with the polyelectrolytic nature of solution is proposed as the suitable mechanisms for the formation of high aspect ratio nanofibers in polyamide-6.

  10. Incorporation of functionalized gold nanoparticles into nanofibers for enhanced attachment and differentiation of mammalian cells

    Directory of Open Access Journals (Sweden)

    Jung Dongju

    2012-06-01

    Full Text Available Abstract Background Electrospun nanofibers have been widely used as substrata for mammalian cell culture owing to their structural similarity to natural extracellular matrices. Structurally consistent electrospun nanofibers can be produced with synthetic polymers but require chemical modification to graft cell-adhesive molecules to make the nanofibers functional. Development of a facile method of grafting functional molecules on the nanofibers will contribute to the production of diverse cell type-specific nanofiber substrata. Results Small molecules, peptides, and functionalized gold nanoparticles were successfully incorporated with polymethylglutarimide (PMGI nanofibers through electrospinning. The PMGI nanofibers functionalized by the grafted AuNPs, which were labeled with cell-adhesive peptides, enhanced HeLa cell attachment and potentiated cardiomyocyte differentiation of human pluripotent stem cells. Conclusions PMGI nanofibers can be functionalized simply by co-electrospinning with the grafting materials. In addition, grafting functionalized AuNPs enable high-density localization of the cell-adhesive peptides on the nanofiber. The results of the present study suggest that more cell type-specific synthetic substrata can be fabricated with molecule-doped nanofibers, in which diverse functional molecules are grafted alone or in combination with other molecules at different concentrations.

  11. Electrospun Nanopaper and its Applications to Microsystems

    Science.gov (United States)

    Lingaiah, Shivalingappa; Shivakumar, Kunigal; Sadler, Robert

    2014-01-01

    A new method of preparing Nylon-66 nanopaper using electrospun nonwoven nanofiber and fiber fusing is presented. The fusing temperature for Nylon-66 nanofiber was found to be 190°C. Both carbon and glass fiber reinforced nanopapers were prepared. The unreinforced Nylon-66 nanopaper of areal density 4.5 g/m2 had a modulus and strength of 681 MPa and 92.8 MPa, respectively, while the unfused nanopaper had 430 MPa and 59.3 MPa, respectively. This increase was attributed to fusing of randomly oriented fibers. Several types of insect wings, namely FlyTech dragonfly and Deadalus flight system wings, were fabricated and tested for their flyability. Vibration test was conducted to measure the wing stiffness by matching the measured first natural frequency to the stiffness.

  12. Tissue engineering scaffolds electrospun from cotton cellulose.

    Science.gov (United States)

    He, Xu; Cheng, Long; Zhang, Ximu; Xiao, Qiang; Zhang, Wei; Lu, Canhui

    2015-01-22

    Nonwovens of cellulose nanofibers were fabricated by electrospinning of cotton cellulose in its LiCl/DMAc solution. The key factors associated with the electrospinning process, including the intrinsic properties of cellulose solutions, the rotating speed of collector and the applied voltage, were systematically investigated. XRD data indicated the electrospun nanofibers were almost amorphous. When increasing the rotating speed of the collector, preferential alignment of fibers along the drawing direction and improved molecular orientation were revealed by scanning electron microscope and polarized FTIR, respectively. Tensile tests indicated the strength of the nonwovens along the orientation direction could be largely improved when collected at a higher speed. In light of the excellent biocompatibility and biodegradability as well as their unique porous structure, the nonwovens were further assessed as potential tissue engineering scaffolds. Cell culture experiments demonstrated human dental follicle cells could proliferate rapidly not only on the surface but also in the entire scaffold. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. Engineering of Corneal Tissue through an Aligned PVA/Collagen Composite Nanofibrous Electrospun Scaffold.

    Science.gov (United States)

    Wu, Zhengjie; Kong, Bin; Liu, Rui; Sun, Wei; Mi, Shengli

    2018-02-24

    Corneal diseases are the main reason of vision loss globally. Constructing a corneal equivalent which has a similar strength and transparency with the native cornea, seems to be a feasible way to solve the shortage of donated cornea. Electrospun collagen scaffolds are often fabricated and used as a tissue-engineered cornea, but the main drawback of poor mechanical properties make it unable to meet the requirement for surgery suture, which limits its clinical applications to a large extent. Aligned polyvinyl acetate (PVA)/collagen (PVA-COL) scaffolds were electrospun by mixing collagen and PVA to reinforce the mechanical strength of the collagen electrospun scaffold. Human keratocytes (HKs) and human corneal epithelial cells (HCECs) inoculated on aligned and random PVA-COL electrospun scaffolds adhered and proliferated well, and the aligned nanofibers induced orderly HK growth, indicating that the designed PVA-COL composite nanofibrous electrospun scaffold is suitable for application in tissue-engineered cornea.

  14. Fabrication of Magnetic Nanofibers by Needleless Electrospinning from a Self-Assembling Polymer Ferrofluid Cone Array.

    Science.gov (United States)

    Huang, Weilong; Liu, Bin; Chen, Zhipeng; Wang, Hongjian; Ren, Lei; Jiao, Jiaming; Zhuang, Lin; Luo, Jie; Jiang, Lelun

    2017-09-17

    Magnetic nanofiber has been widely applied in biomedical fields due to its distinctive size, morphology, and properties. We proposed a novel needleless electrospinning method to prepare magnetic nanofibers from the self-assembling "Taylor cones" of poly(vinyl pyrrolidone) (PVP)/Fe₃O₄ ferrofluid (PFF) under the coincident magnetic and electric fields. The results demonstrated that a static PFF Rosensweig instability with a conical protrusion could be obtained under the magnetic field. The tip of the protrusion emitted an electrospinning jet under the coincident magnetic and electric fields. The needleless electrospinning showed a similar process phenomenon in comparison with conventional electrospinning. The prepared nanofibers were composed of Fe₃O₄ particles and PVP polymer. The Fe₃O₄ particles aggregated inside and on the surface of the nanofibers. The nanofibers prepared by needleless electrospinning exhibited similar morphology compared with the conventionally electrospun nanofibers. The nanofibers also exhibited good ferromagnetic and magnetic field responsive properties.

  15. Electrospun biocomposite nanofibrous patch for cardiac tissue engineering

    Energy Technology Data Exchange (ETDEWEB)

    Prabhakaran, Molamma P; Ramakrishna, Seeram [Health Care and Energy Materials Laboratory, Nanoscience and Nanotechnology Initiative, Faculty of Engineering, National University of Singapore, 2 Engineering Drive 3, Singapore 117576 (Singapore); Kai, Dan [NUS Graduate School of Integrative Sciences and Engineering, National University of Singapore (Singapore); Ghasemi-Mobarakeh, Laleh, E-mail: nnimpp@nus.edu.s [Islamic Azad University, Najafabad Branch, Isfahan (Iran, Islamic Republic of)

    2011-10-15

    A bioengineered construct that matches the chemical, mechanical, biological properties and extracellular matrix morphology of native tissue could be suitable as a cardiac patch for supporting the heart after myocardial infarction. The potential of utilizing a composite nanofibrous scaffold of poly(dl-lactide-co-glycolide)/gelatin (PLGA/Gel) as a biomimetic cardiac patch is studied by culturing a population of cardiomyocyte containing cells on the electrospun scaffolds. The chemical characterization and mechanical properties of the electrospun PLGA and PLGA/Gel nanofibers were studied by Fourier transform infrared spectroscopy, scanning electron microscopy and tensile measurements. The biocompatibility of the scaffolds was also studied and the cardiomyocytes seeded on PLGA/Gel nanofibers were found to express the typical functional cardiac proteins such as alpha-actinin and troponin I, showing the easy integration of cardiomyocytes on PLGA/Gel scaffolds. Our studies strengthen the application of electrospun PLGA/Gel nanofibers as a bio-mechanical support for injured myocardium and as a potential substrate for induction of endogenous cardiomyocyte proliferation, ultimately reducing the cardiac dysfunction and improving cardiac remodeling.

  16. The effect of electrospun poly(lactic acid and nanohydroxyapatite nanofibers’ diameter on proliferation and differentiation of mesenchymal stem cells

    Directory of Open Access Journals (Sweden)

    Amir Doustgani

    2016-10-01

    Full Text Available Objective(s: Electrospun nanofibrous mats of poly(lactic acid (PLA and nanohydroxyapatite (nano-HA were prepared and proliferation and differentiation of mesenchymal stem cells on the prepared nanofibers were investigated in this study. Materials and Methods: PLA/nano-HA nanofibers were prepared by electrospinning. The effects of process parameters, such as nano-HA concentration, distance, applied voltage, and flow rate on the mean diameter of electrospun nanofibers were investigated. Scanning electron microscopy (SEM was used to determine the mean fiber diameter of produced nanofibers. Mechanical propertes of nanofibrous mats were evaluated using a universal testing machine. Response surface methodology was used to model the fiber diameter of electrospun PLA/nano-HA nanofibers. Results: The average fiber diameter for optimized nanofibers was 125 ± 11 nm. MTT and ALP results showed that optimization of fiber diameter increased the osteogenic differentiation of stem cells. Conclusion: It could be concluded that optimization of fiber diameter has beneficial effect on cell proliferation and differentiation. Optimized nanofibers of PLA/nano-HA could be good candidates for bone tissue engineering.

  17. Production of Conductive PEDOT-Coated PVA-GO Composite Nanofibers

    Science.gov (United States)

    Zubair, Nur Afifah; Rahman, Norizah Abdul; Lim, Hong Ngee; Sulaiman, Yusran

    2017-02-01

    Electrically conductive nanofiber is well known as an excellent nanostructured material for its outstanding performances. In this work, poly(3,4-ethylenedioxythiophene) (PEDOT)-coated polyvinyl alcohol-graphene oxide (PVA-GO)-conducting nanofibers were fabricated via a combined method using electrospinning and electropolymerization techniques. During electrospinning, the concentration of PVA-GO solution and the applied voltage were deliberately altered in order to determine the optimized electrospinning conditions. The optimized parameters obtained were 0.1 mg/mL of GO concentration with electrospinning voltage of 15 kV, which displayed smooth nanofibrous morphology and smaller diameter distribution. The electrospun PVA-GO nanofiber mats were further modified by coating with the conjugated polymer, PEDOT, using electropolymerization technique which is a facile approach for coating the nanofibers. SEM images of the obtained nanofibers indicated that cauliflower-like structures of PEDOT were successfully grown on the surface of the electrospun nanofibers during the potentiostatic mode of the electropolymerization process. The conductive nature of PEDOT coating strongly depends on the different electropolymerization parameters, resulting in good conductivity of PEDOT-coated nanofibers. The optimum electropolymerization of PEDOT was at a potential of 1.2 V in 5 min. The electrochemical measurements demonstrated that the fabricated PVA-GO/PEDOT composite nanofiber could enhance the current response and reduce the charge transfer resistance of the nanofiber.

  18. Production of Conductive PEDOT-Coated PVA-GO Composite Nanofibers.

    Science.gov (United States)

    Zubair, Nur Afifah; Rahman, Norizah Abdul; Lim, Hong Ngee; Sulaiman, Yusran

    2017-12-01

    Electrically conductive nanofiber is well known as an excellent nanostructured material for its outstanding performances. In this work, poly(3,4-ethylenedioxythiophene) (PEDOT)-coated polyvinyl alcohol-graphene oxide (PVA-GO)-conducting nanofibers were fabricated via a combined method using electrospinning and electropolymerization techniques. During electrospinning, the concentration of PVA-GO solution and the applied voltage were deliberately altered in order to determine the optimized electrospinning conditions. The optimized parameters obtained were 0.1 mg/mL of GO concentration with electrospinning voltage of 15 kV, which displayed smooth nanofibrous morphology and smaller diameter distribution. The electrospun PVA-GO nanofiber mats were further modified by coating with the conjugated polymer, PEDOT, using electropolymerization technique which is a facile approach for coating the nanofibers. SEM images of the obtained nanofibers indicated that cauliflower-like structures of PEDOT were successfully grown on the surface of the electrospun nanofibers during the potentiostatic mode of the electropolymerization process. The conductive nature of PEDOT coating strongly depends on the different electropolymerization parameters, resulting in good conductivity of PEDOT-coated nanofibers. The optimum electropolymerization of PEDOT was at a potential of 1.2 V in 5 min. The electrochemical measurements demonstrated that the fabricated PVA-GO/PEDOT composite nanofiber could enhance the current response and reduce the charge transfer resistance of the nanofiber.

  19. A variable stiffness joint with electrospun P(VDF-TrFE-CTFE) variable stiffness springs

    NARCIS (Netherlands)

    Carloni, Raffaella; Lapp, Valerie I.; Cremonese, Andrea; Belcari, Juri; Zucchelli, Andrea

    This letter presents a novel rotational variable stiffness joint that relies on one motor and a set of variable stiffness springs. The variable stiffness springs are leaf springs with a layered design, i.e., an electro-active layer of electrospun aligned nanofibers of poly(vinylidene

  20. Emulsion Electrospinning as an Approach to Fabricate PLGA/Chitosan Nanofibers for Biomedical Applications

    Science.gov (United States)

    Tavanai, Hossein; Hilborn, Jöns; Donzel-Gargand, Olivier; Leifer, Klaus; Arpanaei, Ayyoob

    2014-01-01

    Novel nanofibers from blends of polylactic-co-glycolic acid (PLGA) and chitosan have been produced through an emulsion electrospinning process. The spinning solution employed polyvinyl alcohol (PVA) as the emulsifier. PVA was extracted from the electrospun nanofibers, resulting in a final scaffold consisting of a blend of PLGA and chitosan. The fraction of chitosan in the final electrospun mat was adjusted from 0 to 33%. Analyses by scanning and transmission electron microscopy show uniform nanofibers with homogenous distribution of PLGA and chitosan in their cross section. Infrared spectroscopy verifies that electrospun mats contain both PLGA and chitosan. Moreover, contact angle measurements show that the electrospun PLGA/chitosan mats are more hydrophilic than electrospun mats of pure PLGA. Tensile strengths of 4.94 MPa and 4.21 MPa for PLGA/chitosan in dry and wet conditions, respectively, illustrate that the polyblend mats of PLGA/chitosan are strong enough for many biomedical applications. Cell culture studies suggest that PLGA/chitosan nanofibers promote fibroblast attachment and proliferation compared to PLGA membranes. It can be assumed that the nanofibrous composite scaffold of PLGA/chitosan could be potentially used for skin tissue reconstruction. PMID:24689041

  1. Compressibility of carbon fabrics with needleless electrospun PAN nanofibrous interleaves

    Directory of Open Access Journals (Sweden)

    S. V. Lomov

    2016-01-01

    Full Text Available The present paper investigates how the presence of nanofiber interleaves affects the compressibility of the layup during manufacturing of the composites and hence determining the theoretically attainable fiber volume fraction at the given processing pressure. The results show that up to the interleave areal density of 10 g/m2 per nanofiber layer the decrease of fiber volume fraction does not exceed 3% for a laminate of carbon fiber woven fabric. Interleaves inside a fabric laminate are more compressible than a plain electrospun veil. It can be explained as the nanofibers penetrate between the carbon fibers when applying compression during composite manufacturing. It can be stated that there is a strong interference between the interleaves and the carbon reinforcement, which can lead to effective toughness improvement of the composite without significant alteration of fiber volume content.

  2. Crosslinked electrospun PVA nanofibrous membranes: elucidation of their physicochemical, physicomechanical and molecular disposition

    International Nuclear Information System (INIS)

    Shaikh, Rubina P; Kumar, Pradeep; Choonara, Yahya E; Du Toit, Lisa C; Pillay, Viness

    2012-01-01

    The effects of modifying electrospun poly(vinyl alcohol) (PVA) nanofibers through crosslinking using glutaraldehyde (GA) are explored in this paper. Various concentrations of PVA solutions containing model drugs rifampicin (RIF) and isoniazid (INH) were electrospun and thereafter crosslinked using GA vapors. PVA nanofibers demonstrated high drug entrapment efficiency of 98.77% ± 1.384% and 95.07% ± 1.988% for the INH- and RIF-loaded PVA nanofibers, respectively. The surface morphology, molecular vibrational transitions, tensile attributes and in vitro drug release were characterized and supported by in silico molecular mechanics simulations. Results indicated that crosslinking caused a significant reduction in the rate of drug release where 81.11% ± 2.35% of INH and 59.31% ± 2.57% of RIF were released after 12 h. Tensile properties such as the ultimate strength and Young's modulus increased after crosslinking, caused by crosslinks forming between PVA nanofibers as was revealed through scanning electron microscopy analysis. Fourier Transform infrared analysis was conducted to further support the mode of crosslinking. Additionally, image processing analysis was carried out to quantify the effect of formulation variables on the morphology of nanofibers. Furthermore, the effect of GA-induced crosslinking and addition of drugs on the performance of electrospun fibers was further elucidated and conceptualized using a molecular mechanics assisted model building and energy refinement approach via molecular mechanics energy relationships by exploring the spatial disposition of energy-minimized molecular structures of the polymer, crosslinker and the drugs. (paper)

  3. Synthesis and characterization of curcumin loaded PLA-Hyperbranched polyglycerol electrospun blend for wound dressing applications.

    Science.gov (United States)

    Perumal, Govindaraj; Pappuru, Sreenath; Chakraborty, Debashis; Maya Nandkumar, A; Chand, Dillip Kumar; Doble, Mukesh

    2017-07-01

    This study is aimed to develop curcumin (Cur) incorporated electrospun nanofibers of a blend of poly (lactic acid) (PLA) and hyperbranched polyglycerol (HPG) for wound healing applications. Both the polymers are synthesized and fabricated by electrospinning technique. The produced nanofibers were characterized by Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FT-IR), Differential Scanning Colorimetry (DSC) and Thermogravimetric Analysis (TGA). Electrospun scaffolds (PLA/HPG/Cur) exhibits very high hydrophilicity, high swelling and drug uptake and promotes better cell viability, adhesion and proliferation when compared to PLA/Cur electrospun nanofibers. Biodegradation study revealed that the morphology of the nanofibers were unaffected even after 14days immersion in Phosphate Buffered Saline. In vitro scratch assay indicates that migration of the cells in the scratch treated with PLA/HPG/Cur is complete within 36h. These results suggest that PLA/HPG/Cur nanofibers can be a potential wound patch dressing for acute and chronic wound applications. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. In Vivo and In Vitro Elution of Analgesics from Multilayered Poly(D,L-lactide-co-glycolide Nanofibers Incorporated Ureteral Stents

    Directory of Open Access Journals (Sweden)

    Yi-Chia Lin

    2018-01-01

    Full Text Available We develop novel analgesic-eluting nanofiber-incorporated ureteral stents that offer sustained release of lidocaine and ketorolac for local drug delivery. Lidocaine and poly(D,L-lactide-co-glycolide (PLGA were dissolved in hexafluoroisopropanol and were electrospun into nonwoven nanofibers onto the surface of ureteral stents. This was followed by electrospinning of another layer of PLGA nanofibers containing ketorolac. Electrospun drug-loaded nanofibers were then characterized using scanning electron microscopy, Fourier transform infrared spectroscopy, and water contact angle analysis. In addition, the elution behavior characteristics of the analgesics, both in vivo and in vitro, from the nanofiber-incorporated stents were evaluated. Experimental results indicate that the analgesic-eluting ureteral stents could liberate high strengths of analgesics in vitro and in vivo for at least 50 and 30 days, respectively. The analgesic-eluting nanofiber-incorporated ureteral stents are potentially applicable for alleviating the discomfort associated with stent implant.

  5. Development of braided drug-loaded nanofiber sutures

    International Nuclear Information System (INIS)

    Hu Wen; Huang Zhengming; Liu Xiangyang

    2010-01-01

    The objectives of this work are twofold. Firstly, while most work on electrospinning is limited to the development of only functional materials, a structural application of electrospun nanofibers is explored. Secondly, a drug-loaded tissue suture is fabricated and its various properties are characterized. Braided drug-loaded nanofiber sutures are obtained by combining an electrospinning process with a braiding technique followed by a coating procedure. Two different electrospinning techniques, i.e. blend and coaxial electrospinning, to incorporate a model drug cefotaxime sodium (CFX-Na) into poly(L-lactic acid) (PLLA) nanofibers have been applied and compared with each other. Properties of the braided drug-loaded sutures are characterized through a variety of methods including SEM, TEM and tensile testing. The results show that the nanofibers had a preferable micromorphology. The drug was incorporated into the polymer nanofibers homogeneously, with no cross-linking. The nanofibers maintained their fibrous structures. An in vitro release study indicates that the drug-loaded nanofibers fabricated by blend electrospinning and coaxial electrospinning had a different drug release behavior. An inhibition zone experiment shows that both sutures obtained from the nanofibers of the different electrospinning techniques had favorable antibacterial properties. The drug-loaded sutures had preferable histological compatibility performance compared with commercial silk sutures in an in vivo comparative study.

  6. Improved electrical conductivity of poly(ethylene oxide) nanofibers using multi-walled carbon nanotubes

    Science.gov (United States)

    Lee, J. Y.; Kang, T.-H.; Choi, J. H.; Choi, I.-S.; Yu, W.-R.

    2018-03-01

    Highly conductive nanofibers with 1570 S/m were obtained from an electrospun solution of polymer containing multiwalled carbon nanotubes (MWCNTs). Homogeneous dispersion of high concentrations of MWCNTs was achieved by attaching poly(styrenesulfonic acid graft aniline) (PSS-g-ANI), an amphiphilic surfactant, to the MWCNT surface. The hydrophilic sulfonic acid group facilitated the dissolution of PSS-g-ANI-grafted MWCNTs in a polyethylene oxide (PEO) solution up to 6.7 wt% MWCNT. To our knowledge, this is the highest level of MWCNT doping attained in a solution designed for electrospinning. With the incorporation of PSS-g-ANI, the concentration of MWCNTs embedded in the electrospun nanofibers increased. More importantly, the alignment of MWCNTs along the nanofiber axis increased significantly, as confirmed by observed birefringence under crossed polarizers. The combination of higher doping levels and better alignment afforded highly conductive nanofibers suitable for electronic nanodevices.

  7. Improved electrical conductivity of poly(ethylene oxide nanofibers using multi-walled carbon nanotubes

    Directory of Open Access Journals (Sweden)

    J. Y. Lee

    2018-03-01

    Full Text Available Highly conductive nanofibers with 1570 S/m were obtained from an electrospun solution of polymer containing multiwalled carbon nanotubes (MWCNTs. Homogeneous dispersion of high concentrations of MWCNTs was achieved by attaching poly(styrenesulfonic acid graft aniline (PSS-g-ANI, an amphiphilic surfactant, to the MWCNT surface. The hydrophilic sulfonic acid group facilitated the dissolution of PSS-g-ANI-grafted MWCNTs in a polyethylene oxide (PEO solution up to 6.7 wt% MWCNT. To our knowledge, this is the highest level of MWCNT doping attained in a solution designed for electrospinning. With the incorporation of PSS-g-ANI, the concentration of MWCNTs embedded in the electrospun nanofibers increased. More importantly, the alignment of MWCNTs along the nanofiber axis increased significantly, as confirmed by observed birefringence under crossed polarizers. The combination of higher doping levels and better alignment afforded highly conductive nanofibers suitable for electronic nanodevices.

  8. Fast Coprecipitation of Calcium Phosphate Nanoparticles inside Gelatin Nanofibers by Tricoaxial Electrospinning

    Directory of Open Access Journals (Sweden)

    Silvia Panzavolta

    2016-01-01

    Full Text Available We present an effective method for fabricating electrospun gelatin nanofibers containing well-dispersed inorganic nanoparticles. The new method encompasses the use of a special triaxial needle where mixing calcium and phosphate aqueous solutions in an intermediate needle yield calcium phosphate (CaP nanoparticles that immediately after precipitation are dragged by the outer polymeric solution and incorporated directly in the electrospinning jet, before nanofiber formation. Gelatin electrospun mats containing different amounts of CaP nanoparticles were prepared and characterized by SEM, TEM, TGA, and stress-strain measurements. The results demonstrate that CaP particles having diameter of few tens of nanometers were successfully introduced in the gelatin nanofibers during the electrospinning process and that they were well dispersed throughout the fiber length. In addition, the use of the special triaxial needle enabled modulating the CaP amount in the nanofibers.

  9. Preparation and Characterization of Levofloxacin-Loaded Nanofibers as Potential Wound Dressings

    Directory of Open Access Journals (Sweden)

    Pásztor Noémi

    2017-06-01

    Full Text Available Objective: The study aimed at obtaining and characterizing levofloxacin-loaded, poly(ε-caprolactone electrospun nanofiber formulations to be used as antibacterial wound dressings. Methods: Drug-loaded nanofibers were obtained by the electrospinning process and their morphology was determined using scanning electron microscopy. Structural analysis of the prepared nanofibers was carried out using differential scanning calorimetry and dissolution testing was performed in order to determine drug release. Results: Both nanofiberous formulations (containing 20 % and 50 % w/w levofloxacin showed dimensions in the range of few hundred nanometers. Thermograms indicated that the formulation containing 20% levofloxacin was totally amorphized, showing a rapid release of the active, in 20 minutes. Conclusions: The poly(ε-caprolactone-based electrospun nanofibers, containing levofloxacin presented suitable characteristics for obtaining potential antibacterial wound dressings.

  10. Highly Sensitive Local Surface Plasmon Resonance in Anisotropic Au Nanoparticles Deposited on Nanofibers

    Directory of Open Access Journals (Sweden)

    Masanari Saigusa

    2015-01-01

    Full Text Available This paper reports the facile and high-throughput fabrication method of anisotropic Au nanoparticles with a highly sensitive local surface plasmon resonance (LPR using cylindrical nanofibers as substrates. The substrates consisting of nanofibers were prepared by the electrospinning of poly(vinylidene fluoride (PVDF. The Au nanoparticles were deposited on the surface of electrospun nanofibers by vacuum evaporation. Scanning electron microscopy revealed the formation of a curved Au island structure on the surface of cylindrical nanofibers. Polarized UV-visible extinction spectroscopy showed anisotropy in their LPR arising from the high surface curvature of the nanofiber. The LPR of the Au nanoparticles on the thinnest nanofiber with a diameter of ~100 nm showed maximum refractive index (RI sensitivity over 500 nm/RI unit (RIU. The close correlation between the fiber diameter dependence of the RI sensitivity and polarization dependence of the LPR suggests that anisotropic Au nanoparticles improve RI sensitivity.

  11. Improving effects of chitosan nanofiber scaffolds on osteoblast proliferation and maturation

    Science.gov (United States)

    Ho, Ming-Hua; Liao, Mei-Hsiu; Lin, Yi-Ling; Lai, Chien-Hao; Lin, Pei-I; Chen, Ruei-Ming

    2014-01-01

    Osteoblast maturation plays a key role in regulating osteogenesis. Electrospun nanofibrous products were reported to possess a high surface area and porosity. In this study, we developed chitosan nanofibers and examined the effects of nanofibrous scaffolds on osteoblast maturation and the possible mechanisms. Macro- and micro observations of the chitosan nanofibers revealed that these nanoproducts had a flat surface and well-distributed fibers with nanoscale diameters. Mouse osteoblasts were able to attach onto the chitosan nanofiber scaffolds, and the scaffolds degraded in a time-dependent manner. Analysis by scanning electron microscopy further showed mouse osteoblasts adhered onto the scaffolds along the nanofibers, and cell–cell communication was also detected. Mouse osteoblasts grew much better on chitosan nanofiber scaffolds than on chitosan films. In addition, human osteoblasts were able to adhere and grow on the chitosan nanofiber scaffolds. Interestingly, culturing human osteoblasts on chitosan nanofiber scaffolds time-dependently increased DNA replication and cell proliferation. In parallel, administration of human osteoblasts onto chitosan nanofibers significantly induced osteopontin, osteocalcin, and alkaline phosphatase (ALP) messenger (m)RNA expression. As to the mechanism, chitosan nanofibers triggered runt-related transcription factor 2 mRNA and protein syntheses. Consequently, results of ALP-, alizarin red-, and von Kossa-staining analyses showed that chitosan nanofibers improved osteoblast mineralization. Taken together, results of this study demonstrate that chitosan nanofibers can stimulate osteoblast proliferation and maturation via runt-related transcription factor 2-mediated regulation of osteoblast-associated osteopontin, osteocalcin, and ALP gene expression. PMID:25246786

  12. Influences of Silver-Doping on the Crystal Structure, Morphology and Photocatalytic Activity of TiO2 Nanofibers

    DEFF Research Database (Denmark)

    Barakat, Nasser A. M.; Kanjwal, Muzafar Ahmed; Al-Deyab, Salem S.

    2011-01-01

    Doping of titanium dioxide nanofibers by silver nanoparticles revealed distinct improvement in the photocatalytic activ-ity; however other influences have not been investigated. In this work, effect of sliver-doping on the crystal structure, the nanofibrous morphology as well as the photocatalytic...... activity of titanium oxide nanofibers has been studied. Sil-ver-doped TiO2 nanofibers having different silver contents were prepared by calcination of electrospun nanofiber mats consisting of silver nitrate, titanium isopropoxide and poly(vinyl acetate) at 600°C. The results affirmed formation of silver...

  13. Polyamic Acid Nanofibers Produced by Needleless Electro spinning

    International Nuclear Information System (INIS)

    Jirsak, O.; Sanetrnik, F.; Hruza, J.; Chaloupek, J.; Sysel, P.

    2010-01-01

    The polyimide precursor (polyamic acid) produced of 4,4'-oxydiphthalic anhydride and 4,4'-oxydianiline was electrospun using needleless electrospinning method. Nonwoven layers consisting of submicron fibers with diameters in the range about 143-470 nm on the polypropylene spunbond supporting web were produced. Filtration properties of these nanofiber layers on the highly permeable polypropylene support namely filtration effectivity and pressure drop were evaluated. Consequently, these polyamic acid fibers were heated to receive polyimide nanofibers. The imidization process has been studied using IR spectroscopy. Some comparisons with the chemically identical polyimide prepared as the film were made.

  14. Electrospun Fibers of Cyclodextrins and Poly(cyclodextrins

    Directory of Open Access Journals (Sweden)

    Alejandro Costoya

    2017-02-01

    Full Text Available Cyclodextrins (CDs can endow electrospun fibers with outstanding performance characteristics that rely on their ability to form inclusion complexes. The inclusion complexes can be blended with electrospinnable polymers or used themselves as main components of electrospun nanofibers. In general, the presence of CDs promotes drug release in aqueous media, but they may also play other roles such as protection of the drug against adverse agents during and after electrospinning, and retention of volatile fragrances or therapeutic agents to be slowly released to the environment. Moreover, fibers prepared with empty CDs appear particularly suitable for affinity separation. The interest for CD-containing nanofibers is exponentially increasing as the scope of applications is widening. The aim of this review is to provide an overview of the state-of-the-art on CD-containing electrospun mats. The information has been classified into three main sections: (i fibers of mixtures of CDs and polymers, including polypseudorotaxanes and post-functionalization; (ii fibers of polymer-free CDs; and (iii fibers of CD-based polymers (namely, polycyclodextrins. Processing conditions and applications are analyzed, including possibilities of development of stimuli-responsive fibers.

  15. Electrospun non-woven nanofibrous hybrid mats based on chitosan and PLA for wound-dressing applications.

    Science.gov (United States)

    Ignatova, Milena; Manolova, Nevena; Markova, Nadya; Rashkov, Iliya

    2009-01-09

    Continuous defect-free nanofibers containing chitosan (Ch) or quaternized chitosan (QCh) were successfully prepared by one-step electrospinning of Ch or QCh solutions mixed with poly[(L-lactide)-co-(D,L-lactide)] in common solvent. XPS revealed the surface chemical composition of the bicomponent electrospun mats. Crosslinked Ch- and QCh-containing nanofibers exhibited higher kill rates against bacteria S. aureus and E. coli than the corresponding solvent-cast films. SEM observations showed that hybrid mats were very effective in suppressing the adhesion of pathogenic bacteria S. aureus. The hybrid nanofibers are promising for wound-healing applications.

  16. Preparation of Ag/HBP/PAN Nanofiber Web and Its Antimicrobial and Filtration Property

    Directory of Open Access Journals (Sweden)

    Li-Rong Yao

    2016-01-01

    Full Text Available To widen the application of nanofibers web in the field of medical health materials, a new Ag/amino-terminated hyperbranched polymer (HBP/polyacrylonitrile (PAN nanofiber web with excellent antimicrobial activity and filtration property was produced with Ag/HBP dispersion solution and PAN nanofiber. Ag/HBP dispersion solution was prepared with HBP as reducer and stabilizer, and Ag/HBP/PAN nanofiber was prepared by modifying electrospun PAN nanofiber with Ag/HBP aqueous solution. The characterization results showed that spherical Ag nanoparticles were prepared and they had a narrow distribution in HBP aqueous solution. The results of Ag/HBP/PAN nanofiber characterized with SEM and EDS showed that the content of silver nanoparticles on the surface of PAN nanofiber was on the increase when the treating temperature rose. The bacterial reduction rates of HBP-treated PAN nanofiber against S. aureus and E. coli were about 89%, while those of the Ag/HBP/PAN nanofiber against S. aureus and E. coli were 99.9% and 99.96%, respectively, due to the cooperative effects from the amino groups in HBP and Ag nanoparticles. Moreover, the small pores and high porosity in Ag/HBP/PAN nanofiber web resulted in high filtration efficiency (99.9% for removing smaller particles (0.1 μm~0.7 μm, which was much higher than that of the gauze mask.

  17. Influence of polyvinyl alcohol amount on producing in situ photo-crosslinked thioamide functionalized nanofiber membranes

    Directory of Open Access Journals (Sweden)

    Zeytuncu Bihter

    2015-01-01

    Full Text Available Poly(vinyl alcohol/maleic anhydride/acryloyl thioamide monomer (PVA/MA/ATM photo-cured nanofiber membranes and pure PVA nanofiber membranes were produced by electrospinning technique. In situ UV radiation was applied during the electrospinning in order to provide polymerization during the jet flight and promote crosslinking of ATM and MA with PVA. The cross-linking was examined by Fourier-transform infrared spectroscopy (FTIR. The morphology and thermal behavior of electrospun nanofiber were characterized by scanning electron microscope (SEM and thermogravimetric analysis (TGA, respectively. The surface area of nanofiber membranes was measured by Brunauer-Emmert-Teller (BET analysis. Furthermore, water durability test was examined. Water durability test demonstrated that in situ photo-cured PVA/MA/ATM nanofiber membrane had the least average mass loss. The surface areas of PVA/MA/ATM nanofiber membranes were 160-280 m2/g. The surface area and diameter of PVA/MA/ATM nanofibers decreased as the PVA content increased. The diameter of nanofibers was obtained less than 100 nm. The results showed that the water-insoluble nanofiber membranes with better chemical and thermal resistance were obtained. These nanofiber membranes may be a promising candidate for the usage of water treatment.

  18. Physico-chemical/biological properties of tripolyphosphate cross-linked chitosan based nanofibers

    International Nuclear Information System (INIS)

    Sarkar, Soumi Dey; Farrugia, Brooke L.; Dargaville, Tim R.; Dhara, Santanu

    2013-01-01

    In this study, chitosan-PEO blend, prepared in a 15 M acetic acid, was electrospun into nanofibers (∼ 78 nm diameter) with bead free morphology. While investigating physico-chemical parameters of blend solutions, effect of yield stress on chitosan based nanofiber fabrication was clearly evidenced. Architectural stability of nanofiber mat in aqueous medium was achieved by ionotropic cross-linking of chitosan by tripolyphosphate (TPP) ions. The TPP cross-linked nanofiber mat showed swelling up to ∼ 300% in 1 h and ∼ 40% degradation during 30 day study period. 3T3 fibroblast cells showed good attachment, proliferation and viability on TPP treated chitosan based nanofiber mats. The results indicate non-toxic nature of TPP cross-linked chitosan based nanofibers and their potential to be explored as a tissue engineering matrix. - Highlights: ► Chitosan based nanofiber fabrication through electrospinning. ► Roles of solution viscosity and yield stress on spinnability of chitosan evidenced. ► Tripolyphosphate (TPP) cross-linking rendered structural stability to nanofibers. ► TPP cross-linking also improved cellular response on chitosan based nanofibers. ► Thus, chitosan based nanofibers are suitable for tissue engineering application

  19. Composite poly(vinyl alcohol/poly(vinyl acetate electrospun nanofibrous mats as a novel wound dressing matrix for controlled release of drugs

    Directory of Open Access Journals (Sweden)

    Jannesari M

    2011-05-01

    Full Text Available Marziyeh Jannesari1, Jaleh Varshosaz2, Mohammad Morshed1, Maedeh Zamani11Department of Textile Engineering, Isfahan University of Technology, Isfahan, Iran; 2Department of Pharmaceutics, School of Pharmacy and Pharmaceutical Sciences Research Center, Isfahan University of Medical Sciences, Isfahan, IranAbstract: The aim of this study was to develop novel biomedicated nanofiber electrospun mats for controlled drug release, especially drug release directly to an injury site to accelerate wound healing. Nanofibers of poly(vinyl alcohol (PVA, poly(vinyl acetate (PVAc, and a 50:50 composite blend, loaded with ciprofloxacin HCl (CipHCl, were successfully prepared by an electrospinning technique for the first time. The morphology and average diameter of the electrospun nanofibers were investigated by scanning electron microscopy. X-ray diffraction studies indicated an amorphous distribution of the drug inside the nanofiber blend. Introducing the drug into polymeric solutions significantly decreased solution viscosities as well as nanofiber diameter. In vitro drug release evaluations showed that both the kind of polymer and the amount of drug loaded greatly affected the degree of swelling, weight loss, and initial burst and rate of drug release. Blending PVA and PVAc exhibited a useful and convenient method for electrospinning in order to control the rate and period of drug release in wound healing applications. Also, the thickness of the blend nanofiber mats strongly influenced the initial release and rate of drug release.Keywords: biodegradable polymers, drug delivery, controlled release, electrospun nanofibers, wound dressing

  20. Chitosan-Intercalated Montmorillonite/Poly(vinyl alcohol) Nanofibers as a Platform to Guide Neuronlike Differentiation of Human Dental Pulp Stem Cells.

    Science.gov (United States)

    Ghasemi Hamidabadi, Hatef; Rezvani, Zahra; Nazm Bojnordi, Maryam; Shirinzadeh, Haji; Seifalian, Alexander M; Joghataei, Mohammad Taghi; Razaghpour, Mojgan; Alibakhshi, Abbas; Yazdanpanah, Abolfazl; Salimi, Maryam; Mozafari, Masoud; Urbanska, Aleksandra M; Reis, Rui L; Kundu, Subhas C; Gholipourmalekabadi, Mazaher

    2017-04-05

    In this study, we present a novel chitosan-intercalated montmorillonite/poly(vinyl alcohol) (OMMT/PVA) nanofibrous mesh as a microenvironment for guiding differentiation of human dental pulp stem cells (hDPSCs) toward neuronlike cells. The OMMT was prepared through ion exchange reaction between the montmorillonite (MMT) and chitosan. The PVA solutions containing various concentrations of OMMT were electrospun to form 3D OMMT-PVA nanofibrous meshes. The biomechanical and biological characteristics of the nanofibrous meshes were evaluated by ATR-FTIR, XRD, SEM, MTT, and LDH specific activity, contact angle, and DAPI staining. They were carried out for mechanical properties, overall viability, and toxicity of the cells. The hDPSCs were seeded on the prepared scaffolds and induced with neuronal specific differentiation media at two differentiation stages (2 days at preinduction stage and 6 days at induction stage). The neural differentiation of the cells cultured on the meshes was evaluated by determining the expression of Oct-4, Nestin, NF-M, NF-H, MAP2, and βIII-tubulin in the cells after preinduction, at induction stages by real-time PCR (RT-PCR) and immunostaining. All the synthesized nanofibers exhibited a homogeneous morphology with a favorable mechanical behavior. The population of the cells differentiated into neuronlike cells in all the experimental groups was significantly higher than that in control group. The expression level of the neuronal specific markers in the cells cultured on 5% OMMT/PVA meshes was significantly higher than the other groups. This study demonstrates the feasibility of the OMMT/PVA artificial nerve graft cultured with hDPSCs for regeneration of damaged neural tissues. These fabricated matrices may have a potential in neural tissue engineering applications.

  1. Enhancing Crystallinity and Orientation by Hot-Stretching to Improve the Mechanical Properties of Electrospun Partially Aligned Polyacrylonitrile (PAN) Nanocomposites

    Science.gov (United States)

    Song, Zhenyu; Hou, Xiaoxiao; Zhang, Liqun; Wu, Sizhu

    2011-01-01

    Partially aligned polyacrylonitrile (PAN)-based nanofibers were electrospun from PAN and PAN/single-walled carbon nanotubes (SWNTs) in a solution of dimethylformamide (DMF) to make the nanofiber composites. The as-spun nanofibers were then hot-stretched in the oven to enhance its orientation and crystallinity. With the introduction of SWNTs and by the hot-stretched process, the mechanical properties will be enhanced correspondingly. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray scattering (XRD), differential scanning calorimetry (DSC), and the tensile test were used to characterize the microstructure and performances of the nanofibers. The orientation and crystallinity of the as-spun and hot-stretched nanofibers confirmed by X-ray have increased. Differential scanning calorimetry showed that the glass transition temperature of PAN increased about 3 °C by an addition of 0.75 wt% SWNTs indicating a strong interfacial interaction between PAN and SWNTs. The tensile strength and the modulus of the nanofibers increased revealing significant load transfer across the nanotube-matrix interface. For PAN nanofibers, the improved fiber alignment, orientation and crystallinity resulted in enhanced mechanical properties, such as the tensile strength and modulus of the nanofibers. It was concluded that the hot-stretched nanofiber and the PAN/SWNTs nanofibers can be used as a potential precursor to produce high-performance nanocomposites. PMID:28879944

  2. Enhancing Crystallinity and Orientation by Hot-Stretching to Improve the Mechanical Properties of Electrospun Partially Aligned Polyacrylonitrile (PAN Nanocomposites

    Directory of Open Access Journals (Sweden)

    Xiaoxiao Hou

    2011-04-01

    Full Text Available Partially aligned polyacrylonitrile (PAN-based nanofibers were electrospun from PAN and PAN/single-walled carbon nanotubes (SWNTs in a solution of dimethylformamide (DMF to make the nanofiber composites. The as-spun nanofibers were then hot-stretched in the oven to enhance its orientation and crystallinity. With the introduction of SWNTs and by the hot-stretched process, the mechanical properties will be enhanced correspondingly. Scanning electron microscopy (SEM, transmission electron microscopy (TEM, X-ray scattering (XRD, differential scanning calorimetry (DSC, and the tensile test were used to characterize the microstructure and performances of the nanofibers. The orientation and crystallinity of the as-spun and hot-stretched nanofibers confirmed by X-ray have increased. Differential scanning calorimetry showed that the glass transition temperature of PAN increased about 3 °C by an addition of 0.75 wt% SWNTs indicating a strong interfacial interaction between PAN and SWNTs. The tensile strength and the modulus of the nanofibers increased revealing significant load transfer across the nanotube-matrix interface. For PAN nanofibers, the improved fiber alignment, orientation and crystallinity resulted in enhanced mechanical properties, such as the tensile strength and modulus of the nanofibers. It was concluded that the hot-stretched nanofiber and the PAN/SWNTs nanofibers can be used as a potential precursor to produce high-performance nanocomposites.

  3. Enhancing Crystallinity and Orientation by Hot-Stretching to Improve the Mechanical Properties of Electrospun Partially Aligned Polyacrylonitrile (PAN) Nanocomposites.

    Science.gov (United States)

    Song, Zhenyu; Hou, Xiaoxiao; Zhang, Liqun; Wu, Sizhu

    2011-04-06

    Partially aligned polyacrylonitrile (PAN)-based nanofibers were electrospun from PAN and PAN/single-walled carbon nanotubes (SWNTs) in a solution of dimethylformamide (DMF) to make the nanofiber composites. The as-spun nanofibers were then hot-stretched in the oven to enhance its orientation and crystallinity. With the introduction of SWNTs and by the hot-stretched process, the mechanical properties will be enhanced correspondingly. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray scattering (XRD), differential scanning calorimetry (DSC), and the tensile test were used to characterize the microstructure and performances of the nanofibers. The orientation and crystallinity of the as-spun and hot-stretched nanofibers confirmed by X-ray have increased. Differential scanning calorimetry showed that the glass transition temperature of PAN increased about 3 °C by an addition of 0.75 wt% SWNTs indicating a strong interfacial interaction between PAN and SWNTs. The tensile strength and the modulus of the nanofibers increased revealing significant load transfer across the nanotube-matrix interface. For PAN nanofibers, the improved fiber alignment, orientation and crystallinity resulted in enhanced mechanical properties, such as the tensile strength and modulus of the nanofibers. It was concluded that the hot-stretched nanofiber and the PAN/SWNTs nanofibers can be used as a potential precursor to produce high-performance nanocomposites.

  4. Novel 'nano in nano' composites for sustained drug delivery: biodegradable nanoparticles encapsulated into nanofiber non-wovens.

    Science.gov (United States)

    Beck-Broichsitter, Moritz; Thieme, Marcel; Nguyen, Juliane; Schmehl, Thomas; Gessler, Tobias; Seeger, Werner; Agarwal, Seema; Greiner, Andreas; Kissel, Thomas

    2010-12-08

    Novel 'nano in nano' composites consisting of biodegradable polymer nanoparticles incorporated into polymer nanofibers may efficiently modulate drug delivery. This is shown here using a combination of model compound-loaded biodegradable nanoparticles encapsulated in electrospun fibers. The dye coumarin 6 is used as model compound for a drug in order to simulate drug release from loaded poly(lactide-co-glycolide) nanoparticles. Dye release from the nanoparticles occurs immediately in aqueous solution. Dye-loaded nanoparticles which are encapsulated by electrospun polymer nanofibers display a significantly retarded release. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Fabrication and Evaluation of Electrospun, 3D-Bioplotted, and Combination of Electrospun/3D-Bioplotted Scaffolds for Tissue Engineering Applications

    Directory of Open Access Journals (Sweden)

    Liliana F. Mellor

    2017-01-01

    Full Text Available Electrospun scaffolds provide a dense framework of nanofibers with pore sizes and fiber diameters that closely resemble the architecture of native extracellular matrix. However, it generates limited three-dimensional structures of relevant physiological thicknesses. 3D printing allows digitally controlled fabrication of three-dimensional single/multimaterial constructs with precisely ordered fiber and pore architecture in a single build. However, this approach generally lacks the ability to achieve submicron resolution features to mimic native tissue. The goal of this study was to fabricate and evaluate 3D printed, electrospun, and combination of 3D printed/electrospun scaffolds to mimic the native architecture of heterogeneous tissue. We assessed their ability to support viability and proliferation of human adipose derived stem cells (hASC. Cells had increased proliferation and high viability over 21 days on all scaffolds. We further tested implantation of stacked-electrospun scaffold versus combined electrospun/3D scaffold on a cadaveric pig knee model and found that stacked-electrospun scaffold easily delaminated during implantation while the combined scaffold was easier to implant. Our approach combining these two commonly used scaffold fabrication technologies allows for the creation of a scaffold with more close resemblance to heterogeneous tissue architecture, holding great potential for tissue engineering and regenerative medicine applications of osteochondral tissue and other heterogeneous tissues.

  6. Raster image correlation spectroscopy as a novel tool to study interactions of macromolecules with nanofiber scaffolds.

    Science.gov (United States)

    Norris, S C P; Humpolíčková, J; Amler, E; Huranová, M; Buzgo, M; Macháň, R; Lukáš, D; Hof, M

    2011-12-01

    Dynamic processes such as diffusion and binding/unbinding of macromolecules (e.g. growth factors or nutrients) are crucial parameters for the design and application of effective artificial tissue materials. Here, dynamics of selected macromolecules were studied in two different composite tissue engineering scaffolds containing an electrospun nanofiber mesh (polycaprolactone or hydrophobically plasma modified polyvinylalcohol-chitosan) encapsulated in agarose hydrogels by a conventional approach fluorescence recovery after photobleaching (FRAP) and a novel technique, raster image correlation spectroscopy (RICS). The two approaches are compared, and it is shown that FRAP is unable to determine processes occurring at low molecular concentrations, especially accurately separating binding/unbinding from diffusion, and its results depend on the concentration of the studied molecules. RICS measures processes of single molecules and, because of its multiple adjustable timescales, can distinguish whether diffusion or binding controls molecular movement and separates fast diffusion from slow transient binding. In addition, RICS provides a robust read-out parameter quantifying binding affinity. Finally, the combination of FRAP and RICS helps to characterize diffusion and binding of macromolecules in tested artificial tissues better, and therefore predicts the behavior of biologically active molecules in these materials for medical applications. Copyright © 2011. Published by Elsevier Ltd.

  7. Poly(ε-caprolactone) Microfiber Meshes for Repeated Oil Retrieval

    OpenAIRE

    Hersey, J. S.; Yohe, S. T.; Grinstaff, M. W.

    2015-01-01

    Electrospun non-woven poly(ε-caprolactone) (PCL) microfiber meshes are described as biodegradable, mechanically robust, and reusable polymeric oil sorbents capable of selectively retrieving oil from simulated oil spills in both fresh and seawater scenarios. Hydrophobic PCL meshes have >99.5% (oil over water) oil selectivity and oil absorption capacities of ~10 grams of oil per gram of sorbent material, which is shown to be a volumetrically driven process. Both the oil selectivity and absorpti...

  8. Development and characterization of the cisplatin loaded nanofibers for the treatment of cervical cancer.

    Science.gov (United States)

    Aggarwal, Urvashi; Goyal, Amit Kumar; Rath, Goutam

    2017-06-01

    A small scale study was carried out to investigate the therapeutic efficacy cisplatin loaded poly-caprolactone/chitosan composite electrospun nanofibers for local chemotherapy of cervical cancers in mice. The prepared nanofibers had shown the sustained release pattern up to one month. Prepared nanofibers were found to have greater mucoadhesive strength. An orthotopic cervical cancer model was established by inducing the EAC cell lines in the vaginal mucosa at cervix region of the mice. Intravaginal administration of the cisplatin loaded nanofibers showed lesser % cell viability as compared to the plain drug. In vivo studies showed a better anti-tumour efficacy of prepared nanofibers in animals at 14th and 21st after the beginning of treatment. Therefore the technique of electrospinning provides a favourable approach for the targeted delivery of the anti-cancer drug via vaginal route against cervical cancer. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Application of Solution-blown 20-50 nm Nanofibers in Filtration of Nanoparticles: The Efficient van der Waals Collectors

    Science.gov (United States)

    Sinha-Ray, Sumit; Sinha-Ray, Suman; Yarin, Alexander; Pourdeyhimi, Behnam

    2015-11-01

    Filtration efficiency of commercially available filter media with fiber/pore sizes on the scale of 10 μm can be dramatically increased by adding a layer of ultrafine supersonically-blown 20-50 nm nanofibers. Different commercial filters were modified with (i) electrospun nanofibers alone, (ii) solution-blown 20-50 nm alone, and (iii) the dual coating with electrospun nanofibers deposited first and the solution-blown 20-50 nm nanofibers deposited on top of them. Detailed observations of nanoparticle removal revealed that the above-mentioned modified filters, especially those with the dual nanofiber coating with the 20-50 nm nanofibers deposited on top, are the most effective in removing the below-200 nm Cu nanoparticles/clusters from aqueous suspensions, in particular at the lowest concentrations of 0.2-0.5 ppm. The theory developed in the present work dealing with convective transport of nanoparticles in the fluid flow along with diffusion of nanoparticles and the van der Waals attraction explains and describes how the smallest solution-blown nanofibers introduce a novel physical mechanism of nanoparticle interception (the attractive van der Waals forces) and become significantly more efficient collectors compared to the larger electrospun nanofibers. The theory also elucidates the morphology of the nanoparticle clusters being accumulated at the smallest nanofiber surfaces, including the clusters growing at the windward side, or in some cases also on the leeward side of a nanofiber. This work is supported by the Nonwovens Cooperative Research Center (NCRC), grant No. 12-144SB.

  10. Antibacterial wound dressing from chitosan/polyethylene oxide nanofibers mats embedded with silver nanoparticles.

    Science.gov (United States)

    Wang, Xiaoli; Cheng, Feng; Gao, Jing; Wang, Lu

    2015-03-01

    Novel antibacterial nanomaterials have been developed for biomedical applications. The present study involves the preparation and properties of antibacterial nanofibers from chitosan/polyethylene oxide electrospun nanofibers incorporated with silver nanoparticles. Silver nanoparticles were efficiently synthesized in situ after ultra violet (UV) with AgNO3 as precursor and chitosan/polyethylene oxide as reducing agent and protecting agent, respectively. Then the resultant solutions were electrospun into nanofibers. The formation of silver nanoparticles was confirmed with ultraviolet visible (UV-vis) and transmission electron microscopy (TEM), and the electrospun nanofibers were characterized by scanning electron microscopy and energy dispersive X-ray. The resultant fibers exhibited uniform morphology with silver nanoparticles distributed throughout the fiber. Also, the fibers showed certain tensile strength and excellent antibacterial activity against Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria. Sustained release of silver nanoparticles from fibers could last for over 72 h. The silver-containing chitosan/polyethylene oxide nanofibers showed excellent cytocompatibility. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

  11. Tactile-Sensing Based on Flexible PVDF Nanofibers via Electrospinning: A Review.

    Science.gov (United States)

    Wang, Xiaomei; Sun, Fazhe; Yin, Guangchao; Wang, Yuting; Liu, Bo; Dong, Mingdong

    2018-01-24

    The flexible tactile sensor has attracted widespread attention because of its great flexibility, high sensitivity, and large workable range. It can be integrated into clothing, electronic skin, or mounted on to human skin. Various nanostructured materials and nanocomposites with high flexibility and electrical performance have been widely utilized as functional materials in flexible tactile sensors. Polymer nanomaterials, representing the most promising materials, especially polyvinylidene fluoride (PVDF), PVDF co-polymer and their nanocomposites with ultra-sensitivity, high deformability, outstanding chemical resistance, high thermal stability and low permittivity, can meet the flexibility requirements for dynamic tactile sensing in wearable electronics. Electrospinning has been recognized as an excellent straightforward and versatile technique for preparing nanofiber materials. This review will present a brief overview of the recent advances in PVDF nanofibers by electrospinning for flexible tactile sensor applications. PVDF, PVDF co-polymers and their nanocomposites have been successfully formed as ultrafine nanofibers, even as randomly oriented PVDF nanofibers by electrospinning. These nanofibers used as the functional layers in flexible tactile sensors have been reviewed briefly in this paper. The β-phase content, which is the strongest polar moment contributing to piezoelectric properties among all the crystalline phases of PVDF, can be improved by adjusting the technical parameters in electrospun PVDF process. The piezoelectric properties and the sensibility for the pressure sensor are improved greatly when the PVDF fibers become more oriented. The tactile performance of PVDF composite nanofibers can be further promoted by doping with nanofillers and nanoclay. Electrospun P(VDF-TrFE) nanofiber mats used for the 3D pressure sensor achieved excellent sensitivity, even at 0.1 Pa. The most significant enhancement is that the aligned electrospun core-shell P

  12. Tactile-Sensing Based on Flexible PVDF Nanofibers via Electrospinning: A Review

    Directory of Open Access Journals (Sweden)

    Xiaomei Wang

    2018-01-01

    Full Text Available The flexible tactile sensor has attracted widespread attention because of its great flexibility, high sensitivity, and large workable range. It can be integrated into clothing, electronic skin, or mounted on to human skin. Various nanostructured materials and nanocomposites with high flexibility and electrical performance have been widely utilized as functional materials in flexible tactile sensors. Polymer nanomaterials, representing the most promising materials, especially polyvinylidene fluoride (PVDF, PVDF co-polymer and their nanocomposites with ultra-sensitivity, high deformability, outstanding chemical resistance, high thermal stability and low permittivity, can meet the flexibility requirements for dynamic tactile sensing in wearable electronics. Electrospinning has been recognized as an excellent straightforward and versatile technique for preparing nanofiber materials. This review will present a brief overview of the recent advances in PVDF nanofibers by electrospinning for flexible tactile sensor applications. PVDF, PVDF co-polymers and their nanocomposites have been successfully formed as ultrafine nanofibers, even as randomly oriented PVDF nanofibers by electrospinning. These nanofibers used as the functional layers in flexible tactile sensors have been reviewed briefly in this paper. The β-phase content, which is the strongest polar moment contributing to piezoelectric properties among all the crystalline phases of PVDF, can be improved by adjusting the technical parameters in electrospun PVDF process. The piezoelectric properties and the sensibility for the pressure sensor are improved greatly when the PVDF fibers become more oriented. The tactile performance of PVDF composite nanofibers can be further promoted by doping with nanofillers and nanoclay. Electrospun P(VDF-TrFE nanofiber mats used for the 3D pressure sensor achieved excellent sensitivity, even at 0.1 Pa. The most significant enhancement is that the aligned

  13. Encapsulation and immobilization of papain in electrospun nanofibrous membranes of PVA cross-linked with glutaraldehyde vapor

    International Nuclear Information System (INIS)

    Moreno-Cortez, Iván E.; Romero-García, Jorge

    2015-01-01

    In this paper, papain enzyme (E.C. 3.4.22.2, 1.6 U/mg) was successfully immobilized in poly(vinyl alcohol) (PVA) nanofibers prepared by electrospinning. The morphology of the electrospun nanofibers was characterized by scanning electron microscopy (SEM) and the diameter distribution was in the range of 80 to 170 nm. The presence of the enzyme within the PVA nanofibers was confirmed by infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDXS) analyses. The maximum catalytic activity was reached when the enzyme loading was 13%. The immobilization of papain in the nanofiber membrane was achieved by chemical crosslinking with a glutaraldehyde vapor treatment (GAvt). The catalytic activity of the immobilized papain was 88% with respect to the free enzyme. The crosslinking time by GAvt to immobilize the enzyme onto the nanofiber mat was 24 h, and the enzyme retained its catalytic activity after six cycles. The crosslinked samples maintained 40% of their initial activity after being stored for 14 days. PVA electrospun nanofibers are excellent matrices for the immobilization of enzymes due to their high surface area and their nanoporous structure. - Highlights: • Successfully attempt to immobilize the papain enzyme in electrospun nanofibers • The morphology of nanofibers did not change at moderate enzyme concentrations. • The retained activity of the immobilized enzyme was 88% relative to the free enzyme. • The immobilized enzyme retains 40% of the initial activity after 14 days of storage. • Potential application of this work in the fabrication of biosensors specialized in the detection of metal ions

  14. Encapsulation and immobilization of papain in electrospun nanofibrous membranes of PVA cross-linked with glutaraldehyde vapor

    Energy Technology Data Exchange (ETDEWEB)

    Moreno-Cortez, Iván E. [Centro de Investigación en Química Aplicada (CIQA), Blvd. Enrique Reyna # 140, San José de los Cerritos, Saltillo, Coahuila 25100, México (Mexico); Universidad Autónoma de Nuevo León (UANL), Fac. de Ingeniería Mecánica y Eléctrica (FIME), Av. Universidad S/N, Cd. Universitaria, San Nicolás de los Garza, Nuevo León C.P. 66450, México (Mexico); Universidad Autónoma de Nuevo León (UANL), Centro de Innovación, Investigación y Desarrollo en Ingeniería y Tecnología (CIIDIT), Apodaca, Nuevo León, México (Mexico); Romero-García, Jorge, E-mail: jromero@ciqa.mx [Centro de Investigación en Química Aplicada (CIQA), Blvd. Enrique Reyna # 140, San José de los Cerritos, Saltillo, Coahuila 25100, México (Mexico); and others

    2015-07-01

    In this paper, papain enzyme (E.C. 3.4.22.2, 1.6 U/mg) was successfully immobilized in poly(vinyl alcohol) (PVA) nanofibers prepared by electrospinning. The morphology of the electrospun nanofibers was characterized by scanning electron microscopy (SEM) and the diameter distribution was in the range of 80 to 170 nm. The presence of the enzyme within the PVA nanofibers was confirmed by infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDXS) analyses. The maximum catalytic activity was reached when the enzyme loading was 13%. The immobilization of papain in the nanofiber membrane was achieved by chemical crosslinking with a glutaraldehyde vapor treatment (GAvt). The catalytic activity of the immobilized papain was 88% with respect to the free enzyme. The crosslinking time by GAvt to immobilize the enzyme onto the nanofiber mat was 24 h, and the enzyme retained its catalytic activity after six cycles. The crosslinked samples maintained 40% of their initial activity after being stored for 14 days. PVA electrospun nanofibers are excellent matrices for the immobilization of enzymes due to their high surface area and their nanoporous structure. - Highlights: • Successfully attempt to immobilize the papain enzyme in electrospun nanofibers • The morphology of nanofibers did not change at moderate enzyme concentrations. • The retained activity of the immobilized enzyme was 88% relative to the free enzyme. • The immobilized enzyme retains 40% of the initial activity after 14 days of storage. • Potential application of this work in the fabrication of biosensors specialized in the detection of metal ions.

  15. An Overview on Application of Natural Substances Incorporated with Electrospun Nanofibrous Scaffolds to Development of Innovative Wound Dressings.

    Science.gov (United States)

    Pilehvar-Soltanahmadi, Younes; Dadashpour, Mehdi; Mohajeri, Abbas; Fattahi, Amir; Sheervalilou, Roghayeh; Zarghami, Nosratollah

    2018-02-14

    Conventional dressings are cost-effective and highly absorbent, but not effectual enough to promote hemostasis, adherence and in holding a moist wound bed. Thanks to the developments in the field of nanotechnology and bioengineering, one of the promising current trends is to move progress of innovative wound dressings, merging the application of traditional healing agents and modern products/ practices, such as hydrocolloids, hydrogels, films and nanofibers. This review surveys on potentials of electrospun nanofibrous mats for wound dressing applications. Furthermore, loading of bioactive molecules and therapeutic agents into the nanofibrous mats especially natural compounds with the aim of fabrication novel bioactive electrospun nanofibrous mats for skin substitutes and wound dressings are discussed. Systematic literature search was conducted to review all recent progress toward the potential of natural substances incorporated with electrospun nanofibrous scaffolds for wound dressing applications. The electrospun nanofibers webs can provide the essential parameters require for wound dressing to heal wounds including absorptivity, oxygen permeability, and non-adherence to the healing tissue, barrier to bacteria, bioactivity and occlusivity. The modern wound dressings materials made of electrospun nanofibers contain various traditional healing agents such as plant derived compounds could be beneficial to the healing of wounds. Natural substances have been used in skin wound care for many years because of their therapeutic properties, including antimicrobial, antioxidant, anti-inflammatory and mitogenic activities. A screening of natural substances with plant or animal sources having high wound healer activities and cooperating with electrospun nanofiber are an important step toward producing innovative bioactive wound dressings. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  16. The impact of relative humidity during electrospinning on the morphology and mechanical properties of nanofibers.

    Science.gov (United States)

    Pelipenko, Jan; Kristl, Julijana; Janković, Biljana; Baumgartner, Saša; Kocbek, Petra

    2013-11-01

    Electrospinning is an efficient and flexible method for nanofiber production, but it is influenced by many systemic, process, and environmental parameters that govern the electrospun product morphology. This study systematically investigates the influence of relative humidity (RH) on the electrospinning process. The results showed that the morphology of the electrospun product (shape and diameter) can be manipulated with precise regulation of RH during electrospinning. Because the diameter of nanofibers correlates with their rigidity, it was shown that RH control can lead to manipulation of material mechanical properties. Finally, based on the solution's rheological parameter-namely, phase shift angle-we were able to predict the loss of homogenous nanofiber structure in correlation with RH conditions during electrospinning. This research addresses the mechanism of RH impact on the electrospinning process and offers the background to exploit it in order to better control nanomaterial properties and alter its applicability. Copyright © 2013 Elsevier B.V. All rights reserved.

  17. Biodegradable Cell-Seeded Nanofiber Scaffolds for Neural Repair

    Directory of Open Access Journals (Sweden)

    Karen C. Cheung

    2011-10-01

    Full Text Available Central and peripheral neural injuries are traumatic and can lead to loss of motor and sensory function, chronic pain, and permanent disability. Strategies that bridge the site of injury and allow axonal regeneration promise to have a large impact on restoring quality of life for these patients. Engineered materials can be used to guide axonal growth. Specifically, nanofiber structures can mimic the natural extracellular matrix, and aligned nanofibers have been shown to direct neurite outgrowth and support axon regeneration. In addition, cell-seeded scaffolds can assist in the remyelination of the regenerating axons. The electrospinning process allows control over fiber diameter, alignment, porosity, and morphology. Biodegradable polymers have been electrospun and their use in tissue engineering has been demonstrated. This paper discusses aspects of electrospun biodegradable nanofibers for neural regeneration, how fiber alignment affects cell alignment, and how cell-seeded scaffolds can increase the effectiveness of such implants.

  18. Electrospun biocompatible Chitosan/MIL-101 (Fe) composite nanofibers for solid-phase extraction ofΔ9-tetrahydrocannabinol in whole blood samples using Box-Behnken experimental design.

    Science.gov (United States)

    Asiabi, Mina; Mehdinia, Ali; Jabbari, Ali

    2017-01-06

    The nanofibers of biocompatible Chitosan/MIL-101 (Fe) composite were synthesized by a simple, cheap and accessible electrospining method and applied for mat-based extraction of trace amount of Δ9-tetrahydrocannabinol (THC) from human whole blood sample following its combination by high performance liquid chromatography-ultraviolet detection. The composite nanofibres were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and N 2 adsorption-desorption experiments. The volume of eluting solvent, sorbent amount, pH and% NaCl (w/v) influencing on the responses were investigated using factorial experimental design. The optimum point was achieved by analysis of the results according to design expert (DX) software. The volume of eluting solvent, sorbent amount and pH were significant variables, and 150μL, 7mg and 7.0 were respectively chosen for obtaining the best extraction response. Under the optimum conditions, the method was exhibited a linear range of 0.1-100μgL -1 (R 2 =0.9943) for THC with a detection limit of 0.04μgL -1 . Acceptable values for intra-day (3.2%) and inter-day (4.8%) relative standard deviations were obtained. The high preconcentration factor (970) and satisfactory recoveries (88.2%-92.4%) in whole blood samples were achieved which proved the capability of the method for trace determination of THC in the human whole blood samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Nanoclay-Directed Structure and Morphology in PVDF Electrospun Membranes

    Directory of Open Access Journals (Sweden)

    Kyunghwan Yoon

    2014-01-01

    Full Text Available The incorporation of organically modified Lucentite nanoclay dramatically modifies the structure and morphology of the PVDF electrospun fibers. In a molecular level, the nanoclay preferentially stabilizes the all-trans conformation of the polymer chain, promoting an α to β transformation of the crystalline phase. The piezoelectric properties of the β-phase carry great promise for energy harvest applications. At a larger scale, the nanoclay facilitates the formation of highly uniform, bead-free fibers. Such an effect can be attributed to the enhanced conductivity and viscoelasticity of the PVDF-clay suspension. The homogenous distribution of the directionally aligned nanoclays imparts advanced mechanical properties to the nanofibers.

  20. Inverse-Leidenfrost phenomenon on nanofiber mats on hot surfaces.

    Science.gov (United States)

    Weickgenannt, Christina M; Zhang, Yiyun; Sinha-Ray, Suman; Roisman, Ilia V; Gambaryan-Roisman, Tatiana; Tropea, Cameron; Yarin, Alexander L

    2011-09-01

    The Leidenfrost effect is a technically and industrially important phenomenon that severely restricts heat removal from high-heat-flux surfaces. A simple remedy to the Leidenfrost effect is provided by polymer nanofiber mats created and deposited by electrospinning on stainless steel surfaces. The influence of nanofiber mats on hydrodynamics and cooling efficiency of single drop impact onto hot surfaces has been investigated experimentally. The evolution of the drops has been recorded by a high-speed complimentary metal-oxide semiconductor camera, whereas the cooling temperature was measured by a thermocouple. A remarkable phenomenon was discovered: a mat of polymer nanofibers electrospun onto a heater surface can completely suppress the Leidenfrost effect, thereby increasing the rate of heat removal from the surface to the liquid drops significantly. The "inverse-Leidenfrost" effect is described qualitatively and quantitatively, providing clear physical reasons for the observed behavior.

  1. Antibacterial polylactic acid/chitosan nanofibers decorated with bioactive glass

    Energy Technology Data Exchange (ETDEWEB)

    Goh, Yi-fan; Akram, Muhammad; Alshemary, Ammarz [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Hussain, Rafaqat, E-mail: rafaqat@comsats.edu.pk [Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan)

    2016-11-30

    Highlights: • PLA/Chitosan nanofibers were coated with functional bioglass. • Polymer/ceramic composite fibers exhibited good in-vitro bioactivity. • Nanofibers coated with Ag doped bioglass exhibited good antibacterial activity. - Abstract: In this study, we have presented the structural and in vitro characterization of electrospun polylactic acid (PLA)/Chitosan nanofibers coated with cerium, copper or silver doped bioactive glasses (CeBG/CuBG/AgBG). Bead-free, smooth surfaced nanofibers were successfully prepared by using electrospinning technique. The nanocomposite fibers were obtained using a facile dip-coating method, their antibacterial activities against E. coliE. coli (ATCC 25922 strains) were measured by the disk diffusion method after 24 h of incubation at 37 °C. CeBG and CuBG decorated PLA/Chitosan nanofibers did not develop an inhibition zone against the bacteria. On the other hand, nanofibers coated with AgBG developed an inhibition zone against the bacteria. The as-prepared nanocomposite fibers were immersed in SBF for 1, 3 and 7 days in Simulated Body Fluid (SBF) for evaluation of in vitro bioactivity. All samples induced the formation of crystallites with roughly ruffled morphology and the pores of fibers were covered with the extensive growth of crystallites. Energy Dispersive X-ray (EDX) composition analysis showed that the crystallites possessed Ca/P ratio close to 1.67, confirming the good in-vitro bioactivity of the fibers.

  2. Titanium Carbide Nanofibers-Reinforced Aluminum Compacts, a New Strategy to Enhance Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Khalil Abdelrazek Khalil

    2016-05-01

    Full Text Available TiC nanofibers reinforced Al matrix composites were produced by High Frequency Induction Heat Sintering (HFIHS.The titanium carbide nanofibers with an average diameter of 90 nm are first prepared by electrospinning technique and high temperature calcination process. A composite solution containing polyacrylonitrile and titanium isopropoxide is first electrospun into the nanofibers, which are subsequently stabilized and then calcined to produce the desired TiC nanofibers. The X-ray diffraction pattern and transmission electron microscopy results show that the main phase of the as-synthesized nanofibers is titanium carbide. The TiC nanofibers is then mixed with the aluminum powders and introduced into high frequency induction heat sintering (HFIHS to produce composites of TiC nanofibers reinforced aluminum matrix. The potential application of the TiC nanofibers reinforced aluminum matrix composites was systematically investigated. 99.5% relative density and around 85 HV (833 MPa Vickers hardness of the Al reinforced with 5 wt % TiC nanofiber has been obtained. Furthermore, the sample of Al contains 5 wt % TiC, has the highest value of compression and yield strength of about 415 and 350 MPa, respectively. The ductility of the Al/5 wt % TiC showed increasing with increasing the TiC contents.

  3. (Au/PANA/PVAc) nanofibers as a novel composite matrix for albumin and streptavidin immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Golshaei, Rana [University of Kashan, Institute of Nano Science and Nano Technology, Kashan, P.O. Box 87317-51167, Islamic Republic of Iran (Iran, Islamic Republic of); Guler, Zeliha [Istanbul Technical University, Nanoscience and Nanoengineering, Maslak, Istanbul 34469 (Turkey); Sarac, Sezai A., E-mail: sarac@itu.edu.tr [Istanbul Technical University, Nanoscience and Nanoengineering, Maslak, Istanbul 34469 (Turkey); Istanbul Technical University, Department of Chemistry and Polymer Science and Technology, Maslak, Istanbul 34469 (Turkey)

    2016-03-01

    A novel electrospun nanofiber mat (Au/PANA/PVAc) consists of (Gold/Poly Anthranilic acid) (Au/PANA) core/shell nanostructures as a support material for protein immobilization that was developed and characterized by electrochemical impedance spectroscopy. In the core/shells, PANA served carboxyl groups (− COOH) for covalent protein immobilization and Au enhanced the electrochemical properties by acting as tiny conduction centers to facilitate electron transfer. Covalent immobilization of albumin and streptavidin as model proteins onto the (Au/PANA/PVAc) nanofibers was carried out by using 1-ethyl-3-(dimethyl-aminopropyl) carbodiimide hydrochloride (EDC)/N-hydroxyl succinimide (NHS) activation. PVAc nanofibers were compared with Au/PANA/PVAc nanofibers before and after protein immobilization. The successful covalent binding of both albumin and streptavidin onto (Au/PANA/PVAc) nanofibers was confirmed by FTIR-ATR, Electron Microscopy/Energy-Dispersive X-ray Spectroscopy SEM/EDX and Electrochemical impedance spectroscopy (EIS). The nanofibers became resistive due to protein immobilization and the higher charge transfer resistance was observed after higher amount of protein was immobilized. - Highlights: • Au/PANA/PVAc nanofibers with (COOH) groups as a suitable supports for covalent immobilization of proteins. • Increasing of the resistivity of the nanofibers after immobilization of the proteins. • Activation of Au/PANA/PVAc nanofibers by using EDC/NHS.

  4. Silver nanoparticle/chitosan oligosaccharide/poly(vinyl alcohol) nanofibers as wound dressings: a preclinical study

    Science.gov (United States)

    Li, Chenwen; Fu, Ruoqiu; Yu, Caiping; Li, Zhuoheng; Guan, Haiyan; Hu, Daqiang; Zhao, Dehua; Lu, Laichun

    2013-01-01

    In this study, a mixture of poly(vinyl alcohol) (PVA) and chitosan oligosaccharides (COS) was electrospun with silver nanoparticles (AgNPs) to produce fibrous mats for use in wound healing. The AgNPs were reduced by COS prior to electrospinning or Ag+ was reduced via ultraviolet irradiation in nanofibers. The morphologies of the PVA/COS/AgNO3 and PVA/COS-AgNP nanofibers were analyzed by scanning electron microscopy. Formation of the AgNPs was investigated by field emission transmission electron microscopy, ultraviolet-visible spectroscopy, Fourier transform infrared spectroscopy, and X-ray diffraction. We also evaluated the biocompatibility of the nanofibers, particularly their cytotoxicity to human skin fibroblasts and potential to cause primary skin irritation. The in vitro antibacterial activity and in vivo wound healing capacity of the nanofibers were also investigated. The nanofibers had a smooth surface with an average diameter of 130–192 nm. The diameters of the AgNPs were in the range of 15–22 nm. The nanofibers significantly inhibited growth of Escherichia coli and Staphylococcus aureus bacteria. PVA/COS-AgNP nanofibers accelerated the rate of wound healing over that of the control (gauze). The results of our in vitro and in vivo animal experiments suggest that PVA/COS-AgNP nanofibers should be of greater interest than PVA/COS/AgNO3 nanofibers for clinical use as a bioactive wound dressing. PMID:24204142

  5. Advances in Poly(4-aminodiphenylaniline) Nanofibers Preparation by Electrospinning Technique.

    Science.gov (United States)

    Della Pina, C; Busacca, C; Frontera, P; Antonucci, P L; Scarpino, L A; Sironi, A; Falletta, E

    2016-05-01

    Polyaniline (PANI) nanofibers are drawing a great deal of interest from academia and industry due to their multiple applications, especially in biomedical field. PANI nanofibers were successfully electrospun for the first time by MacDiarmid and co-workers at the beginning of the millennium and since then many efforts have been addressed to improve their quality. However, traditional PANI prepared from aniline monomer shows some drawbacks, such as presence of toxic (i.e., benzidine) and inorganic (salts and metals) co-products, that complicate polymer post-treatment, and low solubility in common organic solvents, making