Analysis on electronic control unit of continuously variable transmission

Science.gov (United States)

Cao, Shuanggui

Continuously variable transmission system can ensure that the engine work along the line of best fuel economy, improve fuel economy, save fuel and reduce harmful gas emissions. At the same time, continuously variable transmission allows the vehicle speed is more smooth and improves the ride comfort. Although the CVT technology has made great development, but there are many shortcomings in the CVT. The CVT system of ordinary vehicles now is still low efficiency, poor starting performance, low transmission power, and is not ideal controlling, high cost and other issues. Therefore, many scholars began to study some new type of continuously variable transmission. The transmission system with electronic systems control can achieve automatic control of power transmission, give full play to the characteristics of the engine to achieve optimal control of powertrain, so the vehicle is always traveling around the best condition. Electronic control unit is composed of the core processor, input and output circuit module and other auxiliary circuit module. Input module collects and process many signals sent by sensor and , such as throttle angle, brake signals, engine speed signal, speed signal of input and output shaft of transmission, manual shift signals, mode selection signals, gear position signal and the speed ratio signal, so as to provide its corresponding processing for the controller core.

Improvement of diesel engine performance by hydraulically powered electronic control (mechatronics) system. Hakuyo diesel kikan no mechatronics system ni yoru seino kojo

Energy Technology Data Exchange (ETDEWEB)

Sonoda, K.; Nakamura, Y.; Kajima, T.; Sato, S.; Fujii, T.; Tobe, Y. (Kawasaki Heavy Industries, Ltd., Tokyo (Japan))

1992-07-20

This paper describes new hydraulically-actuated mechanisms for both fuel injection and inlet/exhaust valve operation of diesel engines through solenoid valves, which obviate the conventional cam-driven system. These mechanisms were integrated with an electronic control unit also developed in this study and they were mounted as a mechatronics system'' on a power-increased single-cylinder engine. This mechatronics system was mainly composed of an injection control. boost and accumulation component, an inlet and exhaust valve control component, a solenoid valve, an electronic control equipment, a hydraulic power unit, and a maneuvering unit. The verification test was carried out for the improvement of diesel engine performance by the hydraulically powered mechatronics system. As a result, it was proved not only that these mechanisms provide stable operating characteristics over a wide range of conditions, but also that the electronic control system allows accurate, smooth response. 3 refs., 23 figs., 2 tabs.

Electronics Engineering Department Thrust Area report FY'84

International Nuclear Information System (INIS)

Minichino, C.; Phelps, P.L.

1984-01-01

This report describes the work of the Electronics Engineering Department Thrust Areas for FY'84: diagnostics and microelectronic engineering; signal and control engineering; microwave and pulsed power engineering; computer-aided engineering; engineering modeling and simulation; and systems engineering. For each Thrust Area, an overview and a description of the goals and achievements of each project is provided

A comprehensive overview of hybrid electric vehicle: Powertrain configurations, powertrain control techniques and electronic control units

Energy Technology Data Exchange (ETDEWEB)

Cagatay Bayindir, Kamil; Goezuekuecuek, Mehmet Ali; Teke, Ahmet [Cukurova University, Department of Electrical and Electronics Engineering, Balcali, Saricam, Adana (Turkey)

2011-02-15

The studies for hybrid electrical vehicle (HEV) have attracted considerable attention because of the necessity of developing alternative methods to generate energy for vehicles due to limited fuel based energy, global warming and exhaust emission limits in the last century. HEV incorporates internal composition engine, electric machines and power electronic equipments. In this study, overview of HEVs with a focus on hybrid configurations, energy management strategies and electronic control units are presented. Advantages and disadvantages of each configuration are clearly emphasized. The existing powertrain control techniques for HEVs are classified and comprehensively described. Electronic control units used in HEV configuration are also elaborated. The latest trends and technological challenges in the near future for HEVs are discussed. (author)

Fully printable, strain-engineered electronic wrap for customizable soft electronics.

Science.gov (United States)

Byun, Junghwan; Lee, Byeongmoon; Oh, Eunho; Kim, Hyunjong; Kim, Sangwoo; Lee, Seunghwan; Hong, Yongtaek

2017-03-24

Rapid growth of stretchable electronics stimulates broad uses in multidisciplinary fields as well as industrial applications. However, existing technologies are unsuitable for implementing versatile applications involving adaptable system design and functions in a cost/time-effective way because of vacuum-conditioned, lithographically-predefined processes. Here, we present a methodology for a fully printable, strain-engineered electronic wrap as a universal strategy which makes it more feasible to implement various stretchable electronic systems with customizable layouts and functions. The key aspects involve inkjet-printed rigid island (PRI)-based stretchable platform technology and corresponding printing-based automated electronic functionalization methodology, the combination of which provides fully printed, customized layouts of stretchable electronic systems with simplified process. Specifically, well-controlled contact line pinning effect of printed polymer solution enables the formation of PRIs with tunable thickness; and surface strain analysis on those PRIs leads to the optimized stability and device-to-island fill factor of strain-engineered electronic wraps. Moreover, core techniques of image-based automated pinpointing, surface-mountable device based electronic functionalizing, and one-step interconnection networking of PRIs enable customized circuit design and adaptable functionalities. To exhibit the universality of our approach, multiple types of practical applications ranging from self-computable digital logics to display and sensor system are demonstrated on skin in a customized form.

Fully printable, strain-engineered electronic wrap for customizable soft electronics

Science.gov (United States)

Byun, Junghwan; Lee, Byeongmoon; Oh, Eunho; Kim, Hyunjong; Kim, Sangwoo; Lee, Seunghwan; Hong, Yongtaek

2017-03-01

Rapid growth of stretchable electronics stimulates broad uses in multidisciplinary fields as well as industrial applications. However, existing technologies are unsuitable for implementing versatile applications involving adaptable system design and functions in a cost/time-effective way because of vacuum-conditioned, lithographically-predefined processes. Here, we present a methodology for a fully printable, strain-engineered electronic wrap as a universal strategy which makes it more feasible to implement various stretchable electronic systems with customizable layouts and functions. The key aspects involve inkjet-printed rigid island (PRI)-based stretchable platform technology and corresponding printing-based automated electronic functionalization methodology, the combination of which provides fully printed, customized layouts of stretchable electronic systems with simplified process. Specifically, well-controlled contact line pinning effect of printed polymer solution enables the formation of PRIs with tunable thickness; and surface strain analysis on those PRIs leads to the optimized stability and device-to-island fill factor of strain-engineered electronic wraps. Moreover, core techniques of image-based automated pinpointing, surface-mountable device based electronic functionalizing, and one-step interconnection networking of PRIs enable customized circuit design and adaptable functionalities. To exhibit the universality of our approach, multiple types of practical applications ranging from self-computable digital logics to display and sensor system are demonstrated on skin in a customized form.

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine tests in auxiliary power unit (APU... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...

Reliable design of electronic equipment an engineering guide

CERN Document Server

Natarajan, Dhanasekharan

2014-01-01

This book explains reliability techniques with examples from electronics design for the benefit of engineers. It presents the application of de-rating, FMEA, overstress analyses and reliability improvement tests for designing reliable electronic equipment. Adequate information is provided for designing computerized reliability database system to support the application of the techniques by designers. Pedantic terms and the associated mathematics of reliability engineering discipline are excluded for the benefit of comprehensiveness and practical applications. This book offers excellent support

ANP applied to electronics engineering project selection

International Nuclear Information System (INIS)

Habib, M.

2010-01-01

Project selection in Electronics engineering is a complex decision-making process. This research paper illustrates an application of ANP/AHP process. The AHP (Analytic Hierarchy Process) is employed to break down large unstructured decision problems into manageable and measureable components. The ANP, as the general form of AHP, is powerful to deal with complex decisions where interdependence exists in a decision model. The research paper discusses the use of the ANP, a general form of Saaty's analytic Network process, as a model to evaluate the value of competing Electronics projects. The research paper concludes with a case study describing the implementation of this model at an engineering college, including data based on the actual use of the decision making model. The case study helps to verify that AHP is an effective and efficient decision-making tool. A major contribution of this work is to provide a methodology for assessing the best project. Despite a number of publications applying AHP in project selection, this is probably the first time that an attempt has been made to apply AHP in an electronics project selection in an engineering university environment. (author)

Ultra-low-energy wide electron exposure unit

International Nuclear Information System (INIS)

Yonago, Akinobu; Oono, Yukihiko; Tokunaga, Kazutoshi; Kishimoto, Junichi; Wakamoto, Ikuo

2001-01-01

Heat and ultraviolet ray processes are used in surface dryness of paint, surface treatment of construction materials and surface sterilization of food containers. A process using a low-energy wide-area electron beam (EB) has been developed that features high speed and low drive cost. EB processing is not widespread in general industry, however, due to high equipment cost and difficult maintenance. We developed an ultra-low-energy wide-area electron beam exposure unit, the Mitsubishi Wide Electron Exposure Unit (MIWEL) to solve these problems. (author)

Nuclear engineering education in the United States

International Nuclear Information System (INIS)

Williamson, T.G.

1982-01-01

In discussing nuclear engineering education in the United States it is shown that the most critical issue facing the nuclear engineering education community today is enrolment in a time of increasing demand for graduate engineers. Related to the issue of enrolment is support for graduate students, whether it be fellowships, traineeships, or research assistantships. Other issues are those of maintaining a vital faculty in the face of a competitive job market, of maintaining research facilities and developing new ones, and of determining the directions of educational efforts in the future. (U.K.)

Proceedings of 2011 International Conference on Electronic Engineering, Communication and Management

CERN Document Server

Lin, Sally

2012-01-01

This volume presents the main results of 2011 International Conference on Electronic  Engineering, Communication and Management (EECM2011) held December 24-25, 2011, Beijing China. The EECM2011 is an integrated conference providing a valuable opportunity for researchers, scholars and scientists to exchange their ideas face to face together. The main focus of the EECM 2011 and the present 2 volumes “Advances in Electronic Engineering, Communication and Management” is on Power Engineering, Electrical engineering applications, Electrical machines, as well as Communication and Information Systems Engineering.

Proceedings of 2011 International Conference on Electronic Engineering, Communication and Management

CERN Document Server

Lin, Sally

2012-01-01

  This volume presents the main results of 2011 International Conference on Electronic  Engineering, Communication and Management (EECM2011) held December 24-25, 2011, Beijing China. The EECM2011 is an integrated conference providing a valuable opportunity for researchers, scholars and scientists to exchange their ideas face to face together. The main focus of the EECM 2011 and the present 2 volumes “Advances in Electronic Engineering, Communication and Management” is on Power Engineering, Electrical engineering applications, Electrical machines, as well as Communication and Information Systems Engineering.

46 CFR 11.540 - Endorsements for engineers of mobile offshore drilling units.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Endorsements for engineers of mobile offshore drilling units. 11.540 Section 11.540 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY MERCHANT MARINE... § 11.540 Endorsements for engineers of mobile offshore drilling units. Endorsements as chief engineer...

Software Development for EECU Platform of Turbofan Engine

Science.gov (United States)

Kim, Bo Gyoung; Kwak, Dohyup; Kim, Byunghyun; Choi, Hee ju; Kong, Changduk

2017-04-01

The turbofan engine operation consists of a number of hardware and software. The engine is controlled by Electronic Engine Control Unit (EECU). In order to control the engine, EECU communicates with an aircraft system, Actuator Drive Unit (ADU), Engine Power Unit (EPU) and sensors on the engine. This paper tried to investigate the process form starting to taking-off and aims to design the EECU software mode and defined communication data format. The software is implemented according to the designed software mode.

Electronic battlespace facility for research, develoment and engineering

NARCIS (Netherlands)

Jense, Hans; Kuijpers, N.H.L.; Elias, R.J.D.

1997-01-01

In order to support its research, development and engineering activities in the area of distributed simulation for training and command & control, TNO Physics and Electronics Laboratory has developed (and continues to enhance) an Electronic Battlespace Facility (EBF). This paper presents an overview

Electronic ignition system for internal combustion engines

Energy Technology Data Exchange (ETDEWEB)

Crowder, L W

1980-11-20

Mechanical ignition adjustment devices are sensitive to many effects, for example breakage, faults due to manufacturing tolerances, play in the linkage and the effect of a dirty or corrosive environment. It is therefore the purpose of the invention to provide an electronic ignition system which avoids the disadvantages of a mechanical system. The invention provides adjustment of the ignition point, which gives advance of the ignition timing with increasing speed. An output signal is formed, which supersedes the signal supplied by the electronic control system, so that the ignition is advanced. This also occurs with a larger crankshaft angle before top dead centre of the engine. The electronic control system combines with a source of AC time signals which has a generator as electrical transmitter and a DC battery and ignition coil. The rotor of the electrical generator is driven synchronised with the engine. Structural and functional details of the transistor control circuits are given in 5 patent claims.

Engineers' Responsibilities for Global Electronic Waste: Exploring Engineering Student Writing Through a Care Ethics Lens.

Science.gov (United States)

Campbell, Ryan C; Wilson, Denise

2017-04-01

This paper provides an empirically informed perspective on the notion of responsibility using an ethical framework that has received little attention in the engineering-related literature to date: ethics of care. In this work, we ground conceptual explorations of engineering responsibility in empirical findings from engineering student's writing on the human health and environmental impacts of "backyard" electronic waste recycling/disposal. Our findings, from a purposefully diverse sample of engineering students in an introductory electrical engineering course, indicate that most of these engineers of tomorrow associated engineers with responsibility for the electronic waste (e-waste) problem in some way. However, a number of responses suggested attempts to deflect responsibility away from engineers towards, for example, the government or the companies for whom engineers work. Still other students associated both engineers and non-engineers with responsibility, demonstrating the distributed/collective nature of responsibility that will be required to achieve a solution to the global problem of excessive e-waste. Building upon one element of a framework for care ethics adopted from the wider literature, these empirical findings are used to facilitate a preliminary, conceptual exploration of care-ethical responsibility within the context of engineering and e-waste recycling/disposal. The objective of this exploration is to provide a first step toward understanding how care-ethical responsibility applies to engineering. We also hope to seed dialogue within the engineering community about its ethical responsibilities on the issue. We conclude the paper with a discussion of its implications for engineering education and engineering ethics that suggests changes for educational policy and the practice of engineering.

Engine modeling and control modeling and electronic management of internal combustion engines

CERN Document Server

Isermann, Rolf

2014-01-01

The increasing demands for internal combustion engines with regard to fuel consumption, emissions and driveability lead to more actuators, sensors and complex control functions. A systematic implementation of the electronic control systems requires mathematical models from basic design through simulation to calibration. The book treats physically-based as well as models based experimentally on test benches for gasoline (spark ignition) and diesel (compression ignition) engines and uses them for the design of the different control functions. The main topics are: - Development steps for engine control - Stationary and dynamic experimental modeling - Physical models of intake, combustion, mechanical system, turbocharger, exhaust, cooling, lubrication, drive train - Engine control structures, hardware, software, actuators, sensors, fuel supply, injection system, camshaft - Engine control methods, static and dynamic feedforward and feedback control, calibration and optimization, HiL, RCP, control software developm...

First International Conference on Electrical, Electronic and Communications Engineering

CERN Document Server

Vyas, Nalinaksh; Sanei, Saeid; Deb, Kalyanmoy

2017-01-01

The book reports on advanced theories and methods in two related engineering fields: electrical and electronic engineering, and communications engineering and computing. It highlights areas of global and growing importance, such as renewable energy, power systems, mobile communications, security and the Internet of Things (IoT). The contributions cover a number of current research issues, including smart grids, photovoltaic systems, wireless power transfer, signal processing, 4G and 5G technologies, IoT applications, mobile cloud computing and many more. Based on the proceedings of the first International Conference on Emerging Trends in Electrical, Electronic and Communications Engineering (ELECOM 2016), held in Voila Bagatelle, Mauritius from November 25 to 27, 2016, the book provides graduate students, researchers and professionals with a snapshot of the state-of-the-art and a source of new ideas for future research and collaborations.

Imitating model of the electronic regulator frequencies of rotation of the automobile diesel engine

OpenAIRE

Тырловой, С. И.

2011-01-01

The imitating model of an frequency electronic regulator of rotation of high-speed diesel engine an automobile diesel engine with the distributive fuel pump of Bosch company is resulted. Is executed simulation transitive modes of a diesel engine with mechanic and electronic regulators. Deterioration influence plungers steams on dinamic and economic indicators of a diesel engine is analysed. Operational indicators of a diesel engine with mechanic and electronic regulators are compared. The obt...

Electronics Engineering Research. Final report, FY 1979

International Nuclear Information System (INIS)

Weissenberger, S.

1980-01-01

Accomplishments in Electronics Engineering Research (EER) during FY79 spanned a broad range of technologies, from high-speed microelectronics to digital image enhancement; from underground probing with electromagnetic waves to detecting neutrons with a small solid-state device; and from computer systems to aid engineers, to software tools to aid programmers. This report describes the overall EER program and its objectives, summarizes progress made in FY79, and outlines plans for FY80

Bruce Unit 2 lay-up engineering assessment

International Nuclear Information System (INIS)

Iley, D.

1995-01-01

The overall lay-up program initiated as a result of the strategic decision to shut down Bruce A unit 2 is briefly described as an introduction to the engineering assessment of the unit 2 systems. The assessment has identified the need to prepare 67 system and 9 equipment lay-up specifications. A summary of the selected system specifications is described. A complete summary and the specifications and the status of unit 2 systems and equipment required to support lay-up and/or the other three operating units is available on request due to the volume of the information. Some logistical details of the lay-up implementation plans, results, and problems to date demonstrate the complexity of the lay-up requirements for a nuclear unit in a multi-unit CANDU station. (author)

Newnes electronics engineers pocket book

CERN Document Server

Brindley, Keith

2013-01-01

This book is packed with information and material which everyone involved in electronics will find indispensable. Now when you need to know a transistor's characteristics, or an integrated circuit's pinout details, simply look it up! The book is full of tables, symbols, formulae, conversions and illustrations.Promotion via the new Newnes Pocket Book catalogue to the electronics trade will drive sales into the book trade Covers component data; encapsulations; pin-outs; symbols & codings Extensive material on conversion factors, formulae; units and relationships

Palm Power Free-Piston Stirling Engine Control Electronics

Science.gov (United States)

Keiter, Douglas E.; Holliday, Ezekiel

2007-01-01

A prototype 35We, JP-8 fueled, soldier-wearable power system for the DARPA Palm Power program has been developed and tested by Sunpower. A hermetically-sealed 42We Sunpower Free-Piston Stirling Engine (FPSE) with integral linear alternator is the prime mover for this system. To maximize system efficiency over a broad range of output power, a non-dissipative, highly efficient electronic control system which modulates engine output power by varying piston stroke and converts the AC output voltage of the FPSE into 28Vdc for the Palm Power end user, has been designed and demonstrated as an integral component of the Palm Power system. This paper reviews the current status and progress made in developing the control electronics for the Palm Power system, in addition to describing the operation and demonstrated performance of the engine controller in the context of the current JP-8 fueled Palm Power system.

Status of nuclear engineering education in the United States

International Nuclear Information System (INIS)

Brown, G.J.

2000-01-01

Nuclear engineering education in the United States is reflective of the perceived health of the nuclear electric power industry within the country. Just as new commercial reactor orders have vanished and some power plants have shut down, so too have university enrollments shrunk and research reactors closed. This decline in nuclear trained specialists and the disappearance of the nuclear infrastructure is a trend that must be arrested and reversed if the United States is to have a workforce capable of caring for a nuclear power industry to not only meet future electric demand but to ensure that the over 100 existing plants, their supporting facilities and their legacy in the form of high level waste and facility clean-up are addressed. Additionally, the United States has an obligation to support and maintain its nuclear navy and other defence needs. And, lastly, if the United States is to have a meaningful role in the international use of nuclear power with regard to safety, non-proliferation and the environment, then it is imperative that the country continues to produce world-class nuclear engineers and scientists by supporting nuclear engineering education at its universities. The continued support of the federal government. and industry for university nuclear engineering and nuclear energy research and development is essential to sustain the nuclear infrastructure in the United States. Even with this support, and the continued excellent operation of the existing fleet of nuclear electric power plants, it is conceivable that nuclear engineering as an academic discipline may fall victim to poor communications and a tarnished public image. What is needed is a combination of federal and industrial support along with the creativity of the universities to expand their offerings to include more than power production. The objective is a positive message on careers in nuclear related fields, and recognition of the important role of nuclear energy in meeting the country

Methodical recommendations for power unit comprehensive engineering and radiation survey

International Nuclear Information System (INIS)

Nosovskij, A.V.

2000-01-01

The article describes power unit radiation survey methods developed and applied during conduction of Ch NPP unit I Comprehensive Engineering Radiation Survey. Special requirements for units under decommissioning, main survey principals, criteria for definition of volume and the order of survey for various systems of a NPP Unit are included

An Assessment of Research-Doctorate Programs in the United States: Engineering.

Science.gov (United States)

Jones, Lyle V., Ed.; And Others

The quality of doctoral-level chemical engineering (N=79), civil engineering (N=74), electrical engineering (N=91), and mechanical engineering (N=82) programs at United States universities was assessed, using 16 measures. These measures focused on variables related to: (1) program size; (2) characteristics of graduates; (3) reputational factors…

USE OF ELECTRONIC CASE HISTORIES IN OPERATION OF MEDICAL UNITS

Directory of Open Access Journals (Sweden)

I. B. Boltenkova

2016-01-01

Full Text Available Introduction of electronic case histories to medical units including TB units is one of the factors allowing enhancing quality of medical care provision. Use of the electronic case histories provides conditions for information transparency improvement in a medical unit: financial, statistic and medico-technological. Information contained in the electronic case history is important and required both for internal and external use. Use of electronic case histories contributes to reduction of labor costs of workers in medical units, provides fast access of medical personnel to information, formalizes data, provides preservation, invariance and reliability of the information entered into electronic case history during the whole period of storage, regulates the access rights and confidentiality, personifies data and allows unifying health data of all Russian population into one pool.

78 FR 37958 - Special Conditions: Cessna Aircraft Company, Model J182T; Electronic Engine Control System...

Science.gov (United States)

2013-06-25

...; Electronic Engine Control System Installation AGENCY: Federal Aviation Administration (FAA), DOT. ACTION... feature(s) associated with the installation of an electronic engine control. The applicable airworthiness...) fuel. The J182T incorporates an engine controlled by an electronic engine [[Page 37959

Micro-cogeneration units based on Stirling engine for heating and their real operation

Science.gov (United States)

Čierny, Jaroslav; Patsch, Marek

2014-08-01

This article was deal with micro-cogeneration units based on Stirling engine. We watched problematic of real working Stirling engine. The article also contain hookup of unit constructed at University of Zilina.

Electronics engineering research proposals for FY78

International Nuclear Information System (INIS)

Cleland, L.L.; Ekstrom, M.P.; Miller, E.K.

1977-01-01

Since most of the Electronics Engineering Research expenditures are in the Engineering Research Division (ERD), the two are inseparable when discussing plans. A reorganization of ERD aimed at further expanding LLL capabilities and being more responsive to LLL needs is now complete. Six discipline related groups constitute the research elements in ERD. Three groups remained unchanged, one group was modified slightly, two groups were added, and one group was dissolved. The technical activities of each of the six research-oriented groups within ERD are reported

Elements of theoretical mechanics for electronic engineers

CERN Document Server

Bultot, Franz

1965-01-01

Elements of Theoretical Mechanics for Electronic Engineers deals with theoretical mechanics, which is considered one of the fundamental branches of instruction essential to training an engineer. This book discusses the oscillatory motions and their counterparts in electrical circuits and radio, and provides an introduction to differential operators of vector field theory. Other topics covered include systems and functions of vectors; dynamics of a free point; vibrations and waves; and statics. Worked examples and many notes on the application of most sections of the theories to electrical deve

Electrical, electronics, and digital hardware essentials for scientists and engineers

CERN Document Server

Lipiansky, Ed

2012-01-01

A practical guide for solving real-world circuit board problems Electrical, Electronics, and Digital Hardware Essentials for Scientists and Engineers arms engineers with the tools they need to test, evaluate, and solve circuit board problems. It explores a wide range of circuit analysis topics, supplementing the material with detailed circuit examples and extensive illustrations. The pros and cons of various methods of analysis, fundamental applications of electronic hardware, and issues in logic design are also thoroughly examined. The author draws on more than tw

XI Scientific Conference Selected Issues of Electrical Engineering and Electronics (WZEE)

CERN Document Server

Mazur, Damian; Analysis and Simulation of Electrical and Computer Systems

2015-01-01

This book presents the selected results of the XI Scientific Conference Selected Issues of Electrical Engineering and Electronics (WZEE) which was held in Rzeszów and Czarna, Poland on September 27-30, 2013. The main aim of the Conference was to provide academia and industry to discuss and present the latest technological advantages and research results and to integrate the new interdisciplinary scientific circle in the field of electrical engineering, electronics and mechatronics. The Conference was organized by the Rzeszów Division of Polish Association of Theoretical and Applied Electrical Engineering (PTETiS) in cooperation with Rzeszów University of Technology, the Faculty of Electrical and Computer Engineering and Rzeszów University, the Faculty of Mathematics and Natural Sciences.  

Integration issues of a plasma contactor Power Electronics Unit

Science.gov (United States)

Pinero, Luis R.; York, Kenneth W.; Bowers, Glen E.

1995-01-01

A hollow cathode-based plasma contactor is baselined on International Space Station Alpha (ISSA) for spacecraft charge control. The plasma contactor system consists of a hollow cathode assembly (HCA), a power electronics unit (PEU), and an expellant management unit (EMU). The plasma contactor has recently been required to operate in a cyclic mode to conserve xenon expellant and extend system life. Originally, a DC cathode heater converter was baselined for a continuous operation mode because only a few ignitions of the hollow cathode were expected. However, for cyclic operation, a DC heater supply can potentially result in hollow cathode heater component failure due to the DC electrostatic field. This can prevent the heater from attaining the proper cathode tip temperature for reliable ignition of the hollow cathode. To mitigate this problem, an AC cathode heater supply was therefore designed, fabricated, and installed into a modified PEU. The PEU was tested using resistive loads and then integrated with an engineering model hollow cathode to demonstrate stable steady-state operation. Integration issues such as the effect of line and load impedance on the output of the AC cathode heater supply and the characterization of the temperature profile of the heater under AC excitation were investigated.

New Project System for Undergraduate Electronic Engineering

Science.gov (United States)

Chiu, Dirk M.; Chiu, Shen Y.

2005-01-01

A new approach to projects for undergraduate electronic engineering in an Australian university has been applied successfully for over 10 years. This approach has a number of projects running over three year period. Feedback from past graduates and their managers has confirmed that these projects train the students well, giving them the ability…

Environmental aspects of engineering geological mapping in the United States

Science.gov (United States)

Radbruch-Hall, Dorothy H.

1979-01-01

Many engineering geological maps at different scales have been prepared for various engineering and environmental purposes in regions of diverse geological conditions in the United States. They include maps of individual geological hazards and maps showing the effect of land development on the environment. An approach to assessing the environmental impact of land development that is used increasingly in the United States is the study of a single area by scientists from several disciplines, including geology. A study of this type has been made for the National Petroleum Reserve in northern Alaska. In the San Francisco Bay area, a technique has been worked out for evaluating the cost of different types of construction and land development in terms of the cost of a number of kinds of earth science factors. ?? 1979 International Association of Engineering Geology.

The Development Strategies of Electronic Records: United States, Canada, United Kingdom and Australia as Examples

Directory of Open Access Journals (Sweden)

Chiao-Min Lin

2004-09-01

Full Text Available The development of electronic records have been an indicator of modern government all over the world. The format of public records of government agencies have been gradually transformed to digitalform. How to manage the life cycle of electronic records have became an important issue. In this paper, the development strategies in electronic records of the United States, Canada, United Kingdom and Australia are taken as examples to explain their state-of-the-art. Several suggestions are proposed as the reference for Taiwan’s government. [Article content in Chinese

Project No. 7 - Decommissioning unit at Ignalina NPP. (Engineering and project management)

International Nuclear Information System (INIS)

2000-01-01

In order to manage decommissioning process at Ignalina NPP, a new unit should be established in the framework of the Ignalina NPP organizational structure. The on-site Engineering Project Management Unit (PMU) will adopt an integrated approach to project management , engineering design, planning, procurement, safety and licensing activities at Ignalina NPP site. The PMU will assist the Ignalina NPP management in the development of an integrated decommissioning and waste management strategy

Engineering Design and Fabrication of an Ampere-Class Superconducting Photocathode Electron Gun

International Nuclear Information System (INIS)

Ben-Zvi, I.

2008-01-01

Over the past three years, Advanced Energy Systems and Brookhaven National Laboratory (BNL) have been collaborating on the design of an Ampere- class superconducting photocathode electron gun. BNL performed the physics design of the overall system and RF cavity under prior programs. Advanced Energy Systems (AES) is currently responsible for the engineering design and fabrication of the electron gun under contract to BNL. We will report on the engineering design and fabrication status of the superconducting photocathode electron gun. The overall configuration of the cryomodule will be reviewed. The layout of the hermitic string, space frame, shielding package, and cold mass will be discussed. The engineering design of the gun cavity and removable cathode will be presented in detail and areas of technical risk will be highlighted. Finally, the fabrication sequence and fabrication status of the gun cavity will be discussed

Multiple choice questions in electronics and electrical engineering

CERN Document Server

DAVIES, T J

2013-01-01

A unique compendium of over 2000 multiple choice questions for students of electronics and electrical engineering. This book is designed for the following City and Guilds courses: 2010, 2240, 2320, 2360. It can also be used as a resource for practice questions for any vocational course.

Feedforward mapping for engine control

OpenAIRE

Aran, Volkan; Ünel, Mustafa; Unel, Mustafa

2016-01-01

Feedforward control is widely used in electronic control units of internal combustion engines besides feedback controls. However, almost all feedforward control values are used in table form, also called maps, having engine speed and engine torque in their axes. Table approach limits all inte ractions in two input dimensions. This paper focuses on application of Gaussian process modelling of errors of inverse parametric model of the valve position. Validation results based on ...

Information Technology in project-organized electronic and computer technology engineering education

DEFF Research Database (Denmark)

Nielsen, Kirsten Mølgaard; Nielsen, Jens Frederik Dalsgaard

1999-01-01

This paper describes the integration of IT in the education of electronic and computer technology engineers at Institute of Electronic Systems, Aalborg Uni-versity, Denmark. At the Institute Information Technology is an important tool in the aspects of the education as well as for communication...

IEEE [Institute of Electrical and Electronics Engineers] standards and nuclear software quality engineering

International Nuclear Information System (INIS)

Daughtrey, T.

1988-01-01

Significant new nuclear-specific software standards have recently been adopted under the sponsorship of the American Nuclear Society and the American Society of Mechanical Engineers. The interest of the US Nuclear Regulatory Commission has also been expressed through their issuance of NUREG/CR-4640. These efforts all indicate a growing awareness of the need for thorough, referenceable expressions of the way to build in and evaluate quality in nuclear software. A broader professional perspective can be seen in the growing number of software engineering standards sponsored by the Institute of Electrical and Electronics Engineers (IEEE) Computer Society. This family of standards represents a systematic effort to capture professional consensus on quality practices throughout the software development life cycle. The only omission-the implementation phase-is treated by accepted American National Standards Institute or de facto standards for programming languages

Electronic journals: Their use by teachers/researchers of engineering and social sciences

International Nuclear Information System (INIS)

Martins, Fernanda; Machado, Diana; Fernandes, Alberto; Ribeiro, Fernanda

2015-01-01

Libraries must attend the needs of their different users. Academics are usually a particular kind of users with specific needs. Universities are environments where scientific communication is essential and where electronic format of journals is becoming more and more frequently used. This way it becomes increasingly important to understand how academics from different scientific areas use the available electronic resources. The aim of this study is to better understand the existing differences among the users of electronic journals in Engineering and Social Sciences. The research undertaken was mainly focused on the study of the use of electronic journals by teachers/researchers from the Faculties of Engineering and of Arts from the University of Porto, Portugal. In this study an international survey was used in order to characterize the levels of use and access of electronic journals by these communities. The ways of seeking and using scientific information, namely in terms frequency of access, the number of articles consulted, the use of databases and the preference of publishing in electronic journals were analyzed. A set of comparisons were established and results indicate an extensive use of the electronic format, regardless the faculty. However, some differences emerge when it comes to details. Such is the case of the usage rate of reference management software which is considerably more used by Engineering academics than Social Science ones. Generally, electronic journals meeting the information needs of its users and are increasingly used as a preferred means of research. Though, some particular differences in the use of them have emerged, when comparing academics from these two faculties

Electronic journals: Their use by teachers/researchers of engineering and social sciences

Energy Technology Data Exchange (ETDEWEB)

Martins, Fernanda, E-mail: mmartins@letras.up.pt; Machado, Diana, E-mail: mmartins@letras.up.pt; Fernandes, Alberto, E-mail: mmartins@letras.up.pt; Ribeiro, Fernanda, E-mail: mmartins@letras.up.pt [Faculdade de Letras da Universidade do Porto (Portugal)

2015-02-09

Libraries must attend the needs of their different users. Academics are usually a particular kind of users with specific needs. Universities are environments where scientific communication is essential and where electronic format of journals is becoming more and more frequently used. This way it becomes increasingly important to understand how academics from different scientific areas use the available electronic resources. The aim of this study is to better understand the existing differences among the users of electronic journals in Engineering and Social Sciences. The research undertaken was mainly focused on the study of the use of electronic journals by teachers/researchers from the Faculties of Engineering and of Arts from the University of Porto, Portugal. In this study an international survey was used in order to characterize the levels of use and access of electronic journals by these communities. The ways of seeking and using scientific information, namely in terms frequency of access, the number of articles consulted, the use of databases and the preference of publishing in electronic journals were analyzed. A set of comparisons were established and results indicate an extensive use of the electronic format, regardless the faculty. However, some differences emerge when it comes to details. Such is the case of the usage rate of reference management software which is considerably more used by Engineering academics than Social Science ones. Generally, electronic journals meeting the information needs of its users and are increasingly used as a preferred means of research. Though, some particular differences in the use of them have emerged, when comparing academics from these two faculties.

Controlling engineering project changes for multi-unit, multi-site standardized nuclear power plants

International Nuclear Information System (INIS)

Randall, E.; Boddeker, G.; McGugin, H.; Strother, E.; Waggoner, G.

1978-01-01

Multibillioin dollar multiple nuclear power plant projects have numerous potential sources of engineering changes. The majority of these are internally generated changes, client generated changes, and changes from construction, procurement, other engineering organizations, and regulatory organizations. For multiunit, multisite projects, the use of a standardized design is cost effective. Engineering changes can then be controlled for a single standardized design, and the unit or site unique changes can be treated as deviations. Once an effective change procedure is established for change control of the standardized design, the same procedures can be used for control of unit or site unique changes

Enhancing gold recovery from electronic waste via lixiviant metabolic engineering in Chromobacterium violaceum

Science.gov (United States)

Tay, Song Buck; Natarajan, Gayathri; Rahim, Muhammad Nadjad bin Abdul; Tan, Hwee Tong; Chung, Maxey Ching Ming; Ting, Yen Peng; Yew, Wen Shan

2013-01-01

Conventional leaching (extraction) methods for gold recovery from electronic waste involve the use of strong acids and pose considerable threat to the environment. The alternative use of bioleaching microbes for gold recovery is non-pollutive and relies on the secretion of a lixiviant or (bio)chemical such as cyanide for extraction of gold from electronic waste. However, widespread industrial use of bioleaching microbes has been constrained by the limited cyanogenic capabilities of lixiviant-producing microorganisms such as Chromobacterium violaceum. Here we show the construction of a metabolically-engineered strain of Chromobacterium violaceum that produces more (70%) cyanide lixiviant and recovers more than twice as much gold from electronic waste compared to wild-type bacteria. Comparative proteome analyses suggested the possibility of further enhancement in cyanogenesis through subsequent metabolic engineering. Our results demonstrated the utility of lixiviant metabolic engineering in the construction of enhanced bioleaching microbes for the bioleaching of precious metals from electronic waste. PMID:23868689

Engineered Surfaces to Control Secondary Electron Yield for Multipactor Suppression

Science.gov (United States)

2017-09-14

Air Force Institute of Technology AFIT Scholar Theses and Dissertations 9-14-2017 Engineered Surfaces to Control Secondary Electron Yield for...Multipactor Suppression James M. Sattler Follow this and additional works at: https://scholar.afit.edu/etd Part of the Electrical and Electronics Commons... TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED

Integrating E-Learning and Classroom Learning for Engineering Quality Control unit - Curtin University Experience

Directory of Open Access Journals (Sweden)

Ali M. Darabi Golshani

2011-08-01

Full Text Available Engineering employers expect engineering graduates to possess a wide range of skills that goes beyond their technical knowledge. It is vital that graduates have skills which demonstrate that they are responsible for their own development and careers. Some of these skills include; communication abilities, organizational skills, self-promotion, the ability to work as part of a team, be an effective problem solver, be a critical thinker, have good negotiation skills, have the ability to be a leader and being able to network effectively. Department of Civil Engineering at Curtin University of Technology in Perth, Australia offers a Master of Engineering Management degree for Engineers from various disciplines. One of the units taught in this Master degree program is Engineering Quality Control. It was decided to incorporate these non-technical skills in this unit by using an e-learning platform (Blackboard together with an adaptation of the Seven Principles of Good Practice and Dr Meredith Belbin’s team role theory to divide participants into groups. At the end of the unit, most of the participants were showing improvements in their non-technical skills.

Initial closed operation of the CELSS Test Facility Engineering Development Unit

Science.gov (United States)

Kliss, M.; Blackwell, C.; Zografos, A.; Drews, M.; MacElroy, R.; McKenna, R.; Heyenga, A. G.

2003-01-01

As part of the NASA Advanced Life Support Flight Program, a Controlled Ecological Life Support System (CELSS) Test Facility Engineering Development Unit has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The Engineering Development Unit (EDU) is a tightly closed, stringently controlled, ground-based testbed which provides a broad range of environmental conditions under which a variety of CELSS higher plant crops can be grown. Although the EDU was developed primarily to provide near-term engineering data and a realistic determination of the subsystem and system requirements necessary for the fabrication of a comparable flight unit, the EDU has also provided a means to evaluate plant crop productivity and physiology under controlled conditions. This paper describes the initial closed operational testing of the EDU, with emphasis on the hardware performance capabilities. Measured performance data during a 28-day closed operation period are compared with the specified functional requirements, and an example of inferring crop growth parameters from the test data is presented. Plans for future science and technology testing are also discussed. Published by Elsevier Science Ltd on behalf of COSPAR.

Nuclear engineering education in the United States: a status report

International Nuclear Information System (INIS)

Miller, D.W.; Spinrad, B.I.

1986-01-01

The executive summary of the White Paper entitled The Revitalization of Nuclear Energy Education in the United States is the major component of this paper. The White Paper was completed under the auspices of the Nuclear Engineering Department Heads Organization (NEDHO). The presentation highlights events and program changes that have occurred in 1985-1986 following publication of the NEDHO White Paper. Many of these events provide optimism for the revitalization of nuclear engineering education

Advanced Stirling Radioisotope Generator Engineering Unit 2 (ASRG EU2) Final Assembly

Science.gov (United States)

Oriti, Salvatore M.

2015-01-01

NASA Glenn Research Center (GRC) has recently completed the assembly of a unique Stirling generator test article for laboratory experimentation. Under the Advanced Stirling Radioisotope Generator (ASRG) flight development contract, NASA GRC initiated a task to design and fabricate a flight-like generator for in-house testing. This test article was given the name ASRG Engineering Unit 2 (EU2) as it was effectively the second engineering unit to be built within the ASRG project. The intent of the test article was to duplicate Lockheed Martin's qualification unit ASRG design as much as possible to enable system-level tests not previously possible at GRC. After the cancellation of the ASRG flight development project, the decision was made to continue the EU2 build, and make use of a portion of the hardware from the flight development project. GRC and Lockheed Martin engineers collaborated to develop assembly procedures, leveraging the valuable knowledge gathered by Lockheed Martin during the ASRG development contract. The ASRG EU2 was then assembled per these procedures at GRC with Lockheed Martin engineers on site. The assembly was completed in August 2014. This paper details the components that were used for the assembly, and the assembly process itself.

Handbook of power systems engineering with power electronics applications

CERN Document Server

Hase, Yoshihide

2012-01-01

Formerly known as Handbook of Power System Engineering, this second edition provides rigorous revisions to the original treatment of systems analysis together with a substantial new four-chapter section on power electronics applications. Encompassing a whole range of equipment, phenomena, and analytical approaches, this handbook offers a complete overview of power systems and their power electronics applications, and presents a thorough examination of the fundamental principles, combining theories and technologies that are usually treated in separate specialised fields, in a single u

Development of educational complex on electrical engineering, electronics and microcon-trollers on modeling in TINA software

Directory of Open Access Journals (Sweden)

Vladimir A. Alekhin

2017-01-01

Full Text Available The study of electrical engineering, electronics and microcontrollers in accordance with federal state educational standards requires from students the practical mastering of experimental methods for the study of electrical circuits and electronic circuits, the formation of competences and skills in the calculation of electrical circuits and electronic circuits. The modern development of information educational technologies, the widespread use of a variety of computer facilities by students in reducing teaching hours for the study of disciplines make it necessary to create new multimedia training complexes, using computer simulation of electrical circuits, electronic circuits and microcontrollers in the lecture process and in the laboratory and practical exercises. The purpose of the research was a comparative analysis of various computer simulation programs in terms of their accessibility, ease of development and efficiency of use by lecturers and students in the educational process, and the creation and testing of a training complex for the electrical engineering, electronics and microcontrollers using the selected modeling environment.The problems associated with the need to purchase licensed software were discussed and a comparative analysis of the following computer modeling programs for electrical circuits and electronic circuits was performed: NI Multisim, Micro-Cap, Proteus VSM, OrCAD, TINA. The research method included the study of these modeling and design programs, writing of teaching aids and conducting of training sessions with students. The cost of licenses for the software application in computer classes and on students’ home computers was estimated. As a result, the conclusion was confirmed about the advisability of using the free student program of computer modeling TINA-TI and the TINACloud environment from DesignSoft for the teaching of electrical engineering and electronics.The new software product TINACloud uses cloud

Voices from the United Arab Emirates: Engineering Graduates' Labour Market Requisite Competencies

Science.gov (United States)

EL-Sakran, Tharwat M.; Awad, Asmaa

2012-01-01

This study reports on engineering graduates' labour market requisite communication competences and skills in the work environment in the United Arab Emirates (UAE). Its main purpose was to investigate whether internationally required engineering graduates' communication competences were the same in third world countries or different. It used a…

Experimental realization of a Szilard engine with a single electron.

Science.gov (United States)

Koski, Jonne V; Maisi, Ville F; Pekola, Jukka P; Averin, Dmitri V

2014-09-23

The most succinct manifestation of the second law of thermodynamics is the limitation imposed by the Landauer principle on the amount of heat a Maxwell demon (MD) can convert into free energy per single bit of information obtained in a measurement. We propose and realize an electronic MD based on a single-electron box operated as a Szilard engine, where kBT ln 2 of heat is extracted from the reservoir at temperature T per one bit of created information. The information is encoded in the position of an extra electron in the box.

Engineering Encounters: The Cat in the Hat Builds Satellites. A Unit Promoting Scientific Literacy and the Engineering Design Process

Science.gov (United States)

Rehmat, Abeera P.; Owens, Marissa C.

2016-01-01

This column presents ideas and techniques to enhance your science teaching. This month's issue shares information about a unit promoting scientific literacy and the engineering design process. The integration of engineering with scientific practices in K-12 education can promote creativity, hands-on learning, and an improvement in students'…

Electron accelerating unit for streak image tubes

Indian Academy of Sciences (India)

The simulation results show that the accelerating unit improves both the spatial and temporal .... This electron emission process is simulated as a statistical sample in terms of Monte ... solver using above method in MATLAB language. First the .... semiconductors and insulators: Models and measurements. J. Phys. Rev.

Structured electron beams from nano-engineered cathodes

Energy Technology Data Exchange (ETDEWEB)

Lueangaramwong, A. [NICADD, DeKalb; Mihalcea, D. [NICADD, DeKalb; Andonian, G. [RadiaBeam Tech.; Piot, P. [Fermilab

2017-03-07

The ability to engineer cathodes at the nano-scale have open new possibilities such as enhancing quantum eciency via surface-plasmon excitation, forming ultra-low-emittance beams, or producing structured electron beams. In this paper we present numerical investigations of the beam dynamics associated to this class of cathode in the weak- and strong-field regimes.We finally discuss the possible applications of some of the achievable cathode patterns when coupled with other phase space manipulations.

The Impact of Software on Associate Degree Programs in Electronic Engineering Technology.

Science.gov (United States)

Hata, David M.

1986-01-01

Assesses the range and extent of computer assisted instruction software available in electronic engineering technology education. Examines the need for software skills in four areas: (1) high-level languages; (2) assembly language; (3) computer-aided engineering; and (4) computer-aided instruction. Outlines strategies for the future in three…

Gasoline engine management systems and components

CERN Document Server

2015-01-01

The call for environmentally compatible and economical vehicles necessitates immense efforts to develop innovative engine concepts. Technical concepts such as gasoline direct injection helped to save fuel up to 20 % and reduce CO2-emissions. Descriptions of the cylinder-charge control, fuel injection, ignition and catalytic emission-control systems provides comprehensive overview of today´s gasoline engines. This book also describes emission-control systems and explains the diagnostic systems. The publication provides information on engine-management-systems and emission-control regulations. Contents History of the automobile.- Basics of the gasoline engine.- Fuels.- Cylinder-charge control systems.- Gasoline injection systems over the years.- Fuel supply.- Manifold fuel injection.- Gasoline direct injection.- Operation of gasoline engines on natural gas.- Ignition systems over the years.- Inductive ignition systems.- Ignition coils.- Spark plugs.- Electronic control.- Sensors.- Electronic control unit.- Exh...

Examining Teacher Talk in an Engineering Design-Based Science Curricular Unit

Science.gov (United States)

Aranda, Maurina L.; Lie, Richard; Selcen Guzey, S.; Makarsu, Murat; Johnston, Amanda; Moore, Tamara J.

2018-03-01

Recent science education reforms highlight the importance for teachers to implement effective instructional practices that promote student learning of science and engineering content and their practices. Effective classroom discussion has been shown to support the learning of science, but work is needed to examine teachers' enactment of engineering design-based science curricula by focusing on the content, complexity, structure, and orchestration of classroom discussions. In the present study, we explored teacher-student talk with respect to science in a middle school curriculum focused on genetics and genetic engineering. Our study was guided by the following major research question: What are the similarities and differences in teacher talk moves that occurred within an engineering design-based science unit enacted by two teachers? Through qualitative and quantitative approaches, we found that there were clear differences in two teachers' use of questioning strategies and presentation of new knowledge that affected the level of student involvement in classroom discourse and the richness and details of student contributions to the conversations. We also found that the verbal explanations of science content differed between two teachers. Collectively, the findings in this study demonstrate that although the teachers worked together to design an engineering designed-based science curriculum unit, their use of different discussion strategies and patterns, and interactions with students differed to affect classroom discourse.

ASIL determination for motorbike’s Electronics Throttle Control System (ETCS) mulfunction

OpenAIRE

Rokhani Fakhrul Zaman; Abdul Rahman Muhammad Taqiuddin; Kamsani Noor Ain; Mohd Sidek Roslina; Saripan M Iqbal; Samsudin Khairulmizam; Hassan Mohd Khair

2017-01-01

Electronics Throttle Control System (ETCS) is the principal electronic unit in all fuel injection engine motorbike, augmenting the engine performance efficiency in comparison to the conventional carburetor based engine. ETCS is regarded as a safety-critical component, whereby ETCS malfunction can cause unintended acceleration or deceleration event, which can be hazardous to riders. In this study, Hazard Analysis and Risk Assessment, an ISO26262 functional safety standard analysis has been app...

76 FR 55293 - Special Conditions: Diamond Aircraft Industries, Model DA-40NG; Electronic Engine Control (EEC...

Science.gov (United States)

2011-09-07

... with an electronic engine control (EEC), also known as a Full Authority Digital Engine Control (FADEC... engine design certification, and the certification requirements for engine control systems are driven by... aircraft supplied power and data failures on the engine control system, and the resulting effects on engine...

Unified electronic unit for miniature radioactivity logging equipment

International Nuclear Information System (INIS)

Bragin, A.A.; Goldshtejn, L.M.; Fedorov, R.F.; Shikhman, A.S.

1981-01-01

Appropriateness and urgency of the unification of components of radioactivity logging equipment used for the investigation of wells at solid mineral deposits is substantiated. A two-channel electronic unit for miniature equipment for radioactivity logging is described and its basic specifications and performance are given. All functional assemblies of the unit are structurally made in the form of printed circuit boards placed in a pan-shaped chassis 28 mm in diameter. The unit's general design provides for the possibility to attach two probes with detection devices to the unit. The unit is used in the two-channel radioactivity logging instrument ''Kura-2'' and in the two-channel radiometer ''RUR-2''. The outer diameter of these instruments is 48 mm and they ensure the investigation of ore and coal wells with a combination radioactivity methods [ru

SiGe-based re-engineering of electronic warfare subsystems

CERN Document Server

Lambrechts, Wynand

2017-01-01

This book equips readers with a thorough understanding of the applicability of new-generation silicon-germanium (SiGe) electronic subsystems for the military purposes of electronic warfare and defensive countermeasures. The theoretical and technical background is extensively explained and all aspects of the integration of SiGe as an enabling technology for maritime, land, and airborne (including space) electronic warfare are addressed, including research, design, development, and implementation. The coverage is supported by mathematical derivations, informative illustrations, practical examples, and case studies. While SiGe technology provides speed, performance, and price advantages in many markets, sharing of information on its use in electronic warfare systems has to date been limited, especially in developing nations. This book will therefore be warmly welcomed as an engineering guideline that focuses especially on the speed and reliability of current-generation SiGe circuits and highlights emerging innov...

Digital management of an electron microscope unit

International Nuclear Information System (INIS)

Elea, N.; Dickson, M.; Munroe, P.

2002-01-01

Full text: Electron microscope units, especially those such as ours, which operate as a central infrastructural facility are increasingly asked to provide more service, over more instruments with decreasing, or limited, financial resources. We believe that staff time is best used performing electron microscopy, assisting users and maintaining instrumentation rather than in the pursuit of red tape. One solution to this problem has been the creation of a control system which performs all routine acts of data management, such as the archiving and accessing of digital data, providing access to bookings, and most importantly in the era of user pays services, logging time and billing users. The system we have created, developed and expanded allows the users themselves to access our server through any web-browser and make their own bookings or access and manipulate their data. Users themselves must log on to a microscope through swipecard readers before it can be used and log-off after use. Their time is logged precisely and an exquisitely fair user pays systems can be operated by transferring logged usage time to spreadsheets to calculate charges. Furthermore, this system acts as a method of user authentication and can be used to bar incompetent or unauthorised users. The system has recently been upgraded to increase its utility to include sensors that monitor the electron microscope operating environment, such as magnetic field, room temperature, water flow etc, so that if these parameters depart significantly from optimum levels electron microscope unit staff may be alerted. In this presentation the structure of our system will be described and the advantages and disadvantages of such a system will be discussed. Copyright (2002) Australian Society for Electron Microscopy Inc

Electronics circuits and systems

CERN Document Server

Bishop, Owen

2007-01-01

The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Each chapter ends with a set

Electronics circuits and systems

CERN Document Server

Bishop, Owen

2011-01-01

The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Ea

Diesel engine management systems and components

CERN Document Server

2014-01-01

This reference book provides a comprehensive insight into todays diesel injection systems and electronic control. It focusses on minimizing emissions and exhaust-gas treatment. Innovations by Bosch in the field of diesel-injection technology have made a significant contribution to the diesel boom. Calls for lower fuel consumption, reduced exhaust-gas emissions and quiet engines are making greater demands on the engine and fuel-injection systems. Contents History of the diesel engine.- Areas of use for diesel engines.- Basic principles of the diesel engine.- Fuels: Diesel fuel.- Fuels: Alternative fuels.- Cylinder-charge control systems.- Basic principles of diesel fuel-injection.- Overview of diesel fuel-injection systems.- Fuel supply to the low pressure stage.- Overview of discrete cylinder systems.- Unit injector system.- Unit pump system.- Overview of common-rail systems.- High pressure components of the common-rail system.- Injection nozzles.- Nozzle holders.- High pressure lines.- Start assist systems.-...

MODELING OF ELECTRONIC GASOLINE INJECTION PROCESSES IN TWO STROKE ENGINE

Directory of Open Access Journals (Sweden)

Hraivoronskyi, Y.

2013-06-01

Full Text Available Basic provision of the processes developed mode, occurring in ignition fuel system with electronically controlled two stroke engine with positive ignition are given. Fuel injection process’ calculation results for the case of placing fuel injector into intake system presented.

Engine Tune-Up Service. Unit 4: Secondary Circuit. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Morse, David T.

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 4, Secondary Circuit, available separately as CE 031 214. Focus of the posttests is testing and servicing the secondary ignition circuit. One multiple choice posttest is provided that covers the seven performance objectives contained in the unit. (No…

Engine Tune-Up Service. Unit 3: Primary Circuit. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Morse, David T.

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 3, Primary Circuit, available separately as CE 031 211. Focus of the posttests is setting the primary ignition circuit. One multiple choice posttest is provided, covering the eight performance objectives contained in the unit. (No answer key is…

Hydrocarbon emissions from gas engine CHP-units. 2011 measurement program

Energy Technology Data Exchange (ETDEWEB)

Van Dijk, G.H.J. [KEMA, Arnhem (Netherlands)

2012-06-15

In December 2009, the Ministry of Infrastructure and Environment (IandM) issued the Decree on Emission Limits for Middle Sized Combustion Installations (BEMS). This decree imposes a first-time emission limit value (ELV) of 1500 mg C/m{sup 3}{sub o} at 3% O{sub 2} for hydrocarbons emitted by gas engines. IandM used the findings of two hydrocarbon emission measurement programs, executed in 2007 and 2009, as a guideline for this initial ELV. The programs did reveal substantial variation in the hydrocarbon emissions of the gas engines tested. This variation, and especially the uncertainty as to the role of engine and/or other parameters causing such variation, was felt to hamper further policy development. IandM therefore commissioned KEMA to perform follow-up measurements on ten gas engine CHP-units in 2011. Aim of this 2011 program is to assess hydrocarbon emission variation in relation to engine parameters and process conditions including maintenance status, and to atmospheric conditions. The 2011 program comprised two identical measurement sessions, one in spring and one in winter.

Electronic unit for fotovoltaic solar panelling validation

International Nuclear Information System (INIS)

Vazquez, J.; Valverde, J.; Garcia, J.M.

1988-01-01

A low cost and easy to use electronic system for photovoltaic solar panelling validation is described. It measures, with a certain periodicity, voltage and current given by the panel, determines the supplied power, and every so often, its maximum valves. The unit is fitted with a data storage system which allows data recording for later analysis. (Author)

A study experiment of auto idle application in the excavator engine performance

Energy Technology Data Exchange (ETDEWEB)

Purwanto, Wawan, E-mail: wawan5527@gmail.com; Maksum, Hasan; Putra, Dwi Sudarno, E-mail: dwisudarnoputra@ft.unp.ac.id; Wahyudi, Retno [State University of Padang, West Sumatera (Indonesia); Azmi, Meri, E-mail: meriazmi@gmail.com [State Polytechnic of Padang, West Sumatera (Indonesia)

2016-03-29

The purpose of this study was to analyze the effect of applying auto idle to excavator engine performance, such as machine unitization and fuel consumption in Excavator. Steps to be done are to modify the system JA 44 and 67 in Vehicle Electronic Control Unit (V-ECU). The modifications will be obtained from the pattern of the engine speed. If the excavator attachment is not operated, the engine speed will return to the idle speed automatically. From the experiment results the auto idle reduces fuel consumption in excavator engine.

Engine Tune-up Service. Unit 2: Charging System. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Richardson, Roger L.; Bacon, E. Miles

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 2, Charging System, available separately as CE 031 208. Focus of the posttest is on the testing of the charging system. One multiple choice posttest is provided, that covers the three performance objectives contained in the unit. (No answer key is…

Lyapunov-based constrained engine torque control using electronic throttle and variable cam timing

NARCIS (Netherlands)

Feru, E.; Lazar, M.; Gielen, R.H.; Kolmanovsky, I.V.; Di Cairano, S.

2012-01-01

In this paper, predictive control of a spark ignition engine equipped with an electronic throttle and a variable cam timing actuator is considered. The objective is to adjust the throttle angle and the engine cam timing in order to reduce the exhaust gas emissions while maintaining fast and

Validation of a zero-dimensional model for prediction of NOx and engine performance for electronically controlled marine two-stroke diesel engines

DEFF Research Database (Denmark)

Scappin, Fabio; Stefansson, Sigurður H.; Haglind, Fredrik

2012-01-01

The aim of this paper is to derive a methodology suitable for energy system analysis for predicting the performance and NOx emissions of marine low speed diesel engines. The paper describes a zero-dimensional model, evaluating the engine performance by means of an energy balance and a two zone...... experimental data from two MAN B&W engines; one case being data subject to engine parameter changes corresponding to simulating an electronically controlled engine; the second case providing data covering almost all model input and output parameters. The first case of validation suggests that the model can...

Lumped Parameter Modeling for Rapid Vibration Response Prototyping and Test Correlation for Electronic Units

Science.gov (United States)

Van Dyke, Michael B.

2013-01-01

Present preliminary work using lumped parameter models to approximate dynamic response of electronic units to random vibration; Derive a general N-DOF model for application to electronic units; Illustrate parametric influence of model parameters; Implication of coupled dynamics for unit/board design; Demonstrate use of model to infer printed wiring board (PWB) dynamics from external chassis test measurement.

Enhanced identification of eligibility for depression research using an electronic medical record search engine.

Science.gov (United States)

Seyfried, Lisa; Hanauer, David A; Nease, Donald; Albeiruti, Rashad; Kavanagh, Janet; Kales, Helen C

2009-12-01

Electronic medical records (EMRs) have become part of daily practice for many physicians. Attempts have been made to apply electronic search engine technology to speed EMR review. This was a prospective, observational study to compare the speed and clinical accuracy of a medical record search engine vs. manual review of the EMR. Three raters reviewed 49 cases in the EMR to screen for eligibility in a depression study using the electronic medical record search engine (EMERSE). One week later raters received a scrambled set of the same patients including 9 distractor cases, and used manual EMR review to determine eligibility. For both methods, accuracy was assessed for the original 49 cases by comparison with a gold standard rater. Use of EMERSE resulted in considerable time savings; chart reviews using EMERSE were significantly faster than traditional manual review (p=0.03). The percent agreement of raters with the gold standard (e.g. concurrent validity) using either EMERSE or manual review was not significantly different. Using a search engine optimized for finding clinical information in the free-text sections of the EMR can provide significant time savings while preserving clinical accuracy. The major power of this search engine is not from a more advanced and sophisticated search algorithm, but rather from a user interface designed explicitly to help users search the entire medical record in a way that protects health information.

Optimized Matching Lift Unit Transmission Ratio of Engine Driven Ducted Fan

Directory of Open Access Journals (Sweden)

Xiao Senlin

2018-01-01

Full Text Available As a kind of VTOL technology, ducted fan is not only used by many kinds of aircrafts, but also one of the trends of the future aircraft lift system, and attracts more and more attention. For an engine driven ducted fan lift unit, involving the engine and ducted fan matching problem, the form of transmission and transmission ratio are the key design parameters. In order to design and develop a ducted fan aircraft reasonably, a thrust test platform was set up to connect the engine with the ducted fan through the belt driving. The matching relationship between the engine and the transmission system was experimentally studied and the optimal transmission ratio was determined. The results showed that the optimal transmission ratio for the engine 1 is 2.2:1, and for the engine 2, the optimal transmission ratio should be 2.95:1 based on the current ducted and movable blade aerofoil design. At this time, the lift will exceed 130 kg•f, meeting the aircraft's original design requirements.

Advanced cryocooler electronics for space

Energy Technology Data Exchange (ETDEWEB)

Harvey, D.; Danial, A.; Godden, J.; Jackson, M.; McCuskey, J.; Valenzuela, P. [Northrop Grumman Space Technology, Redondo Beach, CA (United States); Davis, T. [Air Force Research Lab., Albuquerque, NM (United States)

2004-08-01

Space pulse-tube cryocoolers require electronics to control the cooling temperature and self-induced vibration. Other functions include engineering diagnostics, telemetry and safety protection of the unit against extreme environments and operational anomalies. The electronics must survive the harsh conditions of launch and orbit, and in some cases severe radiation environments for periods exceeding 10 years. A number of our current generation high reliability radiation hardened electronics units have been launched and others are in various stages of assembly or integration on a number of space flight programs. This paper describes the design features and performance of our next generation flight electronics designed for the STSS payloads. The electronics provides temperature control with better than +/-50 mK short-term stability. Self-induced vibration is controlled to low levels on all harmonics up to the 16th. A unique active power filter limits peak-to-peak reflected ripple current on the primary power bus to less than 3% of the average DC current. The 3 kg unit is capable of delivering 180 W continuous to NGST's high-efficiency cryocooler (HEC). (author)

Efficient EGR technology for future HD diesel engine emission targets

NARCIS (Netherlands)

Baert, R.S.G.; Beckman, D.E.; Veen, A.

1999-01-01

Different systems for achieving short-route cooled EGR on turbocharged and aftercooled heavy-duty diesel engines have been tested on a 12 litre 315 kW engine with 4 valves per cylinder and an electronically controlled unit pump fuel injection system. In all of these systems the exhaust gas was

POLLUTION PREVENTION OPPORTUNITY ASSESSMENT UNITED STATES ARMY CORPS OF ENGINEERS PITTSBURGH ENGINEER WAREHOUSE AND REPAIR STATION AND EMSWORTH LOCKS AND DAMS PITTSBURGH, PENNSYLVANIA

Science.gov (United States)

This report summarizes work conducted at the United States Army Corps of Engineers (USACE) Pittsburgh Engineering Warehouse and Repair Station (PEWARS) and Emsworth Locks and Dams in Pittsburgh, Pennsylvania under the U.S. Environmental Protection Agency's (EPA's) Waste Reduction...

Assessment of Augmented Electronic Fuel Controls for Modular Engine Diagnostics and Condition Monitoring

Science.gov (United States)

1978-12-01

removal of the horoscope . Diagnostic Conoctor - E4 Th10 E4 23-pin connoctor on the electrical control unit Is provided for ground- checking electrical...confidenou in engine condition monitoring * 1min general. Thi9 has boon especially true in~ eases where fUse signal s have c~aused engine shutdowns. Where ECWI

Engineered hybrid cardiac patches with multifunctional electronics for online monitoring and regulation of tissue function

Science.gov (United States)

Feiner, Ron; Engel, Leeya; Fleischer, Sharon; Malki, Maayan; Gal, Idan; Shapira, Assaf; Shacham-Diamand, Yosi; Dvir, Tal

2016-06-01

In cardiac tissue engineering approaches to treat myocardial infarction, cardiac cells are seeded within three-dimensional porous scaffolds to create functional cardiac patches. However, current cardiac patches do not allow for online monitoring and reporting of engineered-tissue performance, and do not interfere to deliver signals for patch activation or to enable its integration with the host. Here, we report an engineered cardiac patch that integrates cardiac cells with flexible, freestanding electronics and a 3D nanocomposite scaffold. The patch exhibited robust electronic properties, enabling the recording of cellular electrical activities and the on-demand provision of electrical stimulation for synchronizing cell contraction. We also show that electroactive polymers containing biological factors can be deposited on designated electrodes to release drugs in the patch microenvironment on demand. We expect that the integration of complex electronics within cardiac patches will eventually provide therapeutic control and regulation of cardiac function.

Engineered hybrid cardiac patches with multifunctional electronics for online monitoring and regulation of tissue function

Science.gov (United States)

Feiner, Ron; Engel, Leeya; Fleischer, Sharon; Malki, Maayan; Gal, Idan; Shapira, Assaf; Shacham-Diamand, Yosi; Dvir, Tal

2016-01-01

In cardiac tissue engineering approaches to treat myocardial infarction, cardiac cells are seeded within three-dimensional porous scaffolds to create functional cardiac patches. However, current cardiac patches do not allow for online monitoring and reporting of engineered-tissue performance, and do not interfere to deliver signals for patch activation or to enable its integration with the host. Here, we report an engineered cardiac patch that integrates cardiac cells with flexible, free-standing electronics and a 3D nanocomposite scaffold. The patch exhibited robust electronic properties, enabling the recording of cellular electrical activities and the on-demand provision of electrical stimulation for synchronizing cell contraction. We also show that electroactive polymers containing biological factors can be deposited on designated electrodes to release drugs in the patch microenvironment on-demand. We expect that the integration of complex electronics within cardiac patches will eventually provide therapeutic control and regulation of cardiac function. PMID:26974408

Characterization of the Advanced Stirling Radioisotope Generator Engineering Unit 2

Science.gov (United States)

Lewandowski, Edward J.; Oriti, Salvatore M.; Schifer, Niholas A.

2016-01-01

Significant progress was made developing the Advanced Stirling Radioisotope Generator (ASRG) 140-W radioisotope power system. While the ASRG flight development project has ended, the hardware that was designed and built under the project is continuing to be tested to support future Stirling-based power system development. NASA Glenn Research Center recently completed the assembly of the ASRG Engineering Unit 2 (EU2). The ASRG EU2 consists of the first pair of Sunpower's Advanced Stirling Convertor E3 (ASC-E3) Stirling convertors mounted in an aluminum housing, and Lockheed Martin's Engineering Development Unit (EDU) 4 controller (a fourth-generation controller). The ASC-E3 convertors and Generator Housing Assembly (GHA) closely match the intended ASRG Qualification Unit flight design. A series of tests were conducted to characterize the EU2, its controller, and the convertors in the flight-like GHA. The GHA contained an argon cover gas for these tests. The tests included measurement of convertor, controller, and generator performance and efficiency; quantification of control authority of the controller; disturbance force measurement with varying piston phase and piston amplitude; and measurement of the effect of spacecraft direct current (DC) bus voltage on EU2 performance. The results of these tests are discussed and summarized, providing a basic understanding of EU2 characteristics and the performance and capability of the EDU 4 controller.

Engineers’ Responsibilities for Global Electronic Waste: Exploring Engineering Student Writing Through a Care Ethics Lens

Science.gov (United States)

Campbell, Ryan C.; Wilson, Denise

2016-01-01

This paper provides an empirically informed perspective on the notion of responsibility using an ethical framework that has received little attention in the engineering-related literature to date: ethics of care. In this work, we ground conceptual explorations of engineering responsibility in empirical findings from engineering student’s writing on the human health and environmental impacts of “backyard” electronic waste recycling/disposal. Our findings, from a purposefully diverse sample of engineering students in an introductory electrical engineering course, indicate that most of these engineers of tomorrow associated engineers with responsibility for the electronic waste (e-waste) problem in some way. However, a number of responses suggested attempts to deflect responsibility away from engineers towards, for example, the government or the companies for whom engineers work. Still other students associated both engineers and non-engineers with responsibility, demonstrating the distributed/collective nature of responsibility that will be required to achieve a solution to the global problem of excessive e-waste. Building upon one element of a framework for care ethics adopted from the wider literature, these empirical findings are used to facilitate a preliminary, conceptual exploration of care-ethical responsibility within the context of engineering and e-waste recycling/disposal. The objective of this exploration is to provide a first step toward understanding how care-ethical responsibility applies to engineering. We also hope to seed dialogue within the engineering community about its ethical responsibilities on the issue. We conclude the paper with a discussion of its implications for engineering education and engineering ethics that suggests changes for educational policy and the practice of engineering. PMID:27368195

Design and Implementation of the Control System of an Internal Combustion Engine Test Unit

Directory of Open Access Journals (Sweden)

Tufan Koç

2014-02-01

Full Text Available Accurate tests and performance analysis of engines are required to minimize measurement errors and so the use of the advanced test equipment is imperative. In other words, the reliable test results depend on the measurement of many parameters and recording the experimental data accurately which is depended on engine test unit. This study aims to design the control system of an internal combustion engine test unit. In the study, the performance parameters of an available internal combustion engine have been transferred to computer in real time. A data acquisition (DAQ card has been used to transfer the experimental data to the computer. Also, a user interface has been developed for performing the necessary procedures by using LabVIEW. The dynamometer load, the fuel consumption, and the desired speed can easily be adjusted precisely by using DAQ card and the user interface during the engine test. Load, fuel consumption, and temperature values (the engine inlet-outlet, exhaust inlet-outlet, oil, and environment can be seen on the interface and also these values can be recorded to the computer. It is expected that developed system will contribute both to the education of students and to the researchers’ studies and so it will eliminate a major lack.

Engine Tune-Up Service. Unit 4: Secondary Circuit. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This student guide is for Unit 4, Secondary Circuit, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test and service the secondary ignition circuit. A companion review exercise book and posttests are available separately as CE 031 215-216. An introduction tells how this unit fits into the total…

Engine Tune-up Service. Unit 2: Charging System. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Richardson, Roger L.; Bacon, E. Miles

This student guide is for Unit 2, Charging System, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test the charging system. A companion review exercise book and posttests are available separately as CE 031 209-210. An introduction tells how this unit fits into the total tune-up service, defines…

Electron transfer reactions in structural units of copper proteins

International Nuclear Information System (INIS)

Faraggi, M.

1975-01-01

In previous pulse radiolysis studies it was suggested that the reduction of the Cu(II) ions in copper proteins by the hydrated electron is a multi-step electron migration process. The technique has been extended to investigate the reduction of some structural units of these proteins. These studies include: the reaction of the hydrated electron with peptides, the reaction of the disulphide bridge with formate radical ion and radicals produced by the reduction of peptides, and the reaction of Cu(II)-peptide complex with esub(aq)sup(-) and CO 2 - . Using these results the reduction mechanism of copper and other proteins will be discussed. (author)

Metal particle emissions in the exhaust stream of diesel engines: an electron microscope study.

Science.gov (United States)

Liati, Anthi; Schreiber, Daniel; Dimopoulos Eggenschwiler, Panayotis; Arroyo Rojas Dasilva, Yadira

2013-12-17

Scanning electron microscopy and transmission electron microscopy were applied to investigate the morphology, mode of occurrence and chemical composition of metal particles (diesel ash) in the exhaust stream of a small truck outfitted with a typical after-treatment system (a diesel oxidation catalyst (DOC) and a downstream diesel particulate filter (DPF)). Ash consists of Ca-Zn-P-Mg-S-Na-Al-K-phases (lube-oil related), Fe, Cr, Ni, Sn, Pb, Sn (engine wear), and Pd (DOC coating). Soot agglomerates of variable sizes (1-5 μm, exceptionally 13 μm), rarely engine wear and escape into the atmosphere.

The 3d International Workshop on Computational Electronics

Science.gov (United States)

Goodnick, Stephen M.

1994-09-01

The Third International Workshop on Computational Electronics (IWCE) was held at the Benson Hotel in downtown Portland, Oregon, on May 18, 19, and 20, 1994. The workshop was devoted to a broad range of topics in computational electronics related to the simulation of electronic transport in semiconductors and semiconductor devices, particularly those which use large computational resources. The workshop was supported by the National Science Foundation (NSF), the Office of Naval Research and the Army Research Office, as well as local support from the Oregon Joint Graduate Schools of Engineering and the Oregon Center for Advanced Technology Education. There were over 100 participants in the Portland workshop, of which more than one quarter represented research groups outside of the United States from Austria, Canada, France, Germany, Italy, Japan, Switzerland, and the United Kingdom. There were a total 81 papers presented at the workshop, 9 invited talks, 26 oral presentations and 46 poster presentations. The emphasis of the contributions reflected the interdisciplinary nature of computational electronics with researchers from the Chemistry, Computer Science, Mathematics, Engineering, and Physics communities participating in the workshop.

Life-Cycle Inventory of Manufacturing Prefinished Engineered Wood Flooring in the Eastern United States

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2010-01-01

Building products have come under increased scrutiny because of environmental impacts from their manufacturing. However, environmental impacts of manufacturing some wood products—such as prefinished engineered wood flooring—have not been determined. This study examined prefinished engineered wood flooring in the eastern United States following the life-cycle inventory...

Engine Tune-Up Service. Unit 3: Primary Circuit. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This student guide is for Unit 3, Primary Circuit, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with how to test the primary ignition circuit. A companion review exercise book and posttests are available separately as CE 031 212-213. An introduction tells how this unit fits into the total tune-up service,…

Electronic Whiteboards and Intensive Care Unit follow up

DEFF Research Database (Denmark)

Østergaard, Kija Lin; Brandrup, Morten

-ended dry-erase whiteboard (make-up-your-own-sentences). In conclusion the primary feature in the two subjects is to optimize communication/collaboration and information between ICU and general wards in the transition. To make it a long term solution the content of such a support would need involvement...... of the end-users in the design process (Participatory Design). Hence these two findings, this review is setting the stage for further research on how electronic whiteboards can support the initial follow up when patients are transferred from an ICU to a general ward.......This paper is reviewing the existing literature on Intensive Care Unit (ICU) Outreach, in-hospital follow up 24 hours after the transition to a general ward from an ICU. It also touches upon the use of Electronic Whiteboards in a hospital setting and how the electronic whiteboards might support...

Professional Training in Software Engineering: A Critical Need in the United States

Directory of Open Access Journals (Sweden)

Jennifer Waldrow

2012-06-01

Full Text Available The software is related to almost every aspect of daily life: manufacturing, banking, travel, communications, defense, medicine, research, government, education, entertainment, law ... Is an essential part of military systems and is used in all civilian sectors, including safety and mission critical. Moreover, the complexity of many of these systems has increased exponentially in recent decades and the software has become an essential component for all of them. Unfortunately, the "systems of higher education", in almost all countries have not kept pace with these changes. The current science and engineering programs, both undergraduate and graduate, they need to incorporate more training in Software Engineering. It is especially true in areas such as aerospace engineering, because these systems are highly dependent on computer, information, communications and software. This article presents an analysis of the current situation of the United States in what has to do with software engineering training that receive and require the aerospace engineers.

Characterizing Twitter Communication--A Case Study of International Engineering Academic Units

Science.gov (United States)

Palmer, Stuart

2014-01-01

Engineering academic units might engage with social media for a range of purposes including for general communication with students, staff, alumni, other important stakeholders and the wider community at large; for student recruitment and for marketing and promotion more generally. This paper presents an investigation into the use of Twitter by…

Impact of distributed generation units with power electronic converters on distribution network protection

NARCIS (Netherlands)

Morren, J.; Haan, de S.W.H.

2008-01-01

An increasing number of distributed generation units (DG units) are connected to the distribution network. These generators affect the operation and coordination of the distribution network protection. The influence from DG units that are coupled to the network with a power electronic converter

Backup control airstart performance on a digital electronic engine control-equipped F100-engine

Science.gov (United States)

Johnson, J. B.

1984-01-01

The air start capability of a backup control (BUC) was tested for a digital electronic engine control (DEEC) equipped F100 engine, which was installed in an F-15 aircraft. Two air start schedules were tested. Using the group 1 start schedule, based on a 40 sec timer, an air speed of 300 knots was required to ensure successful 40 and 25% BUC mode spooldown airstarts. If core rotor speed (N2) was less than 40% a stall would occur when the start bleed closed, 40 sec after initiation of the air start. All jet fuel starter (JFS) assisted air starts were successful with the group 1 start schedule. For the group 2 schedule, the time between pressurization and start bleed closure ranged between 50 sec and 72 sec. Idle rps was lower than the desired 65% for air starts at higher altitudes and lower air speeds.

Advanced Stirling Radioisotope Generator Engineering Unit 2 Anomaly Investigation

Science.gov (United States)

Lewandowski, Edward J.; Dobbs, Michael W.; Oriti, Salvatore M.

2018-01-01

The Advanced Stirling Radioisotope Generator (ASRG) Engineering Unit 2 (EU2) is the highest fidelity electrically heated Stirling radioisotope generator built to date. NASA Glenn Research Center completed the assembly of the ASRG EU2 in September 2014 using hardware from the now cancelled ASRG flight development project. The ASRG EU2 integrated the first pair of Sunpower's Advanced Stirling Convertors (ASC-E3 #1 and #2) in an aluminum generator housing with Lockheed Martin's (LM's) Engineering Development Unit (EDU) 4 controller. After just 179 hr of EU2 generator operation, the first power fluctuation occurred on ASC-E3 #1. The first power fluctuation occurred 175 hr later on ASC-E3 #2. Over time, the power fluctuations became more frequent on both convertors and larger in magnitude. Eventually the EU2 was shut down in January 2015. An anomaly investigation was chartered to determine root cause of the power fluctuations and other anomalous observations. A team with members from Glenn, Sunpower, and LM conducted a thorough investigation of the EU2 anomalies. Findings from the EU2 disassembly identified proximate causes of the anomalous observations. Discussion of the team's assessment of the primary possible failure theories, root cause, and conclusions is provided. Recommendations are made for future Stirling generator development to address the findings from the anomaly investigation. Additional findings from the investigation are also discussed.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT I, GENERAL INTRODUCTION TO DIESEL ENGINES.

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

ONE OF A 30-MODULE COURSE DESIGNED TO UPGRADE THE JOB SKILLS AND TECHNICAL KNOWLEDGE OF DIESEL MAINTENANCE MECHANICS, THIS MATERIAL WAS DEVELOPED BY INDUSTRIAL TRAINING AND SUBJECT-MATTER SPECIALISTS AND TESTED IN INDUSTRIAL TRAINING SITUATIONS. THE PURPOSE OF THIS FIRST UNIT IS TO PROVIDE AN INTRODUCTION TO DIESEL ENGINES BY DEVELOPING AN…

The Development Strategies for the Management Models of the Electronic Documents and Records in the United States, United Kingdom and Australia

Directory of Open Access Journals (Sweden)

Chiu-Yen Lin

2015-06-01

Full Text Available The trend toward electronic government has espoused a large quantity of electronic records, which challenge the existing records management models in the modern countries. This paper describes and compares the development and transition toward electronic records management in the United States, United Kingdom, and Australia to show how the three advanced countries evolved the government records management practices. The analysis emphasized on the holistic policy initiative perspective and compared the directives and regulations, research and development programs and plans, the emerging structures of governance, staffing and professional training, and risk management provisions. The comparison may shed lights on the government electronic management in the other countries. [Article content in Chinese

Engineered hybrid cardiac patches with multifunctional electronics for online monitoring and regulation of tissue function.

Science.gov (United States)

Feiner, Ron; Engel, Leeya; Fleischer, Sharon; Malki, Maayan; Gal, Idan; Shapira, Assaf; Shacham-Diamand, Yosi; Dvir, Tal

2016-06-01

In cardiac tissue engineering approaches to treat myocardial infarction, cardiac cells are seeded within three-dimensional porous scaffolds to create functional cardiac patches. However, current cardiac patches do not allow for online monitoring and reporting of engineered-tissue performance, and do not interfere to deliver signals for patch activation or to enable its integration with the host. Here, we report an engineered cardiac patch that integrates cardiac cells with flexible, freestanding electronics and a 3D nanocomposite scaffold. The patch exhibited robust electronic properties, enabling the recording of cellular electrical activities and the on-demand provision of electrical stimulation for synchronizing cell contraction. We also show that electroactive polymers containing biological factors can be deposited on designated electrodes to release drugs in the patch microenvironment on demand. We expect that the integration of complex electronics within cardiac patches will eventually provide therapeutic control and regulation of cardiac function.

Tracking and Control of Gas Turbine Engine Component Damage/Life

Science.gov (United States)

Jaw, Link C.; Wu, Dong N.; Bryg, David J.

2003-01-01

This paper describes damage mechanisms and the methods of controlling damages to extend the on-wing life of critical gas turbine engine components. Particularly, two types of damage mechanisms are discussed: creep/rupture and thermo-mechanical fatigue. To control these damages and extend the life of engine hot-section components, we have investigated two methodologies to be implemented as additional control logic for the on-board electronic control unit. This new logic, the life-extending control (LEC), interacts with the engine control and monitoring unit and modifies the fuel flow to reduce component damages in a flight mission. The LEC methodologies were demonstrated in a real-time, hardware-in-the-loop simulation. The results show that LEC is not only a new paradigm for engine control design, but also a promising technology for extending the service life of engine components, hence reducing the life cycle cost of the engine.

Engine Tune-up Service. Unit 6: Emission Control Systems. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This student guide is for Unit 6, Emission Control Systems, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with inspecting, testing, and servicing an emission control system. A companion review exercise book and posttests are available separately as CE 031 221-222. An introduction tells how this unit fits…

A Multidisciplinary PBL Robot Control Project in Automation and Electronic Engineering

Science.gov (United States)

Hassan, Houcine; Domínguez, Carlos; Martínez, Juan-Miguel; Perles, Angel; Capella, Juan-Vicente; Albaladejo, José

2015-01-01

This paper presents a multidisciplinary problem-based learning (PBL) project consisting of the development of a robot arm prototype and the implementation of its control system. The project is carried out as part of Industrial Informatics (II), a compulsory third-year course in the Automation and Electronic Engineering (AEE) degree program at the…

Implementation of Microelectronics Track in Electronics Engineering in a Philippines State University

Directory of Open Access Journals (Sweden)

Gil B. Barte

2015-11-01

Full Text Available The evolving trends in electronics continuous to attract students to take upElectronics Engineering.However, it also adds to discipline implementation complexities.Institutions of Higher Learning offering this program must adapt to this realities to avoid obsolescence. This paper looked at Batangas State University, in the Philippines,ongoingimplementation of the Microelectronics track under the Electronics Engineering (ECEProgram. It describes the restructuring done to the ECE curriculum to overcome the enormous complexity inherent in microelectronics design and the teaching pedagogy adopted to promote active learning. The ongoing program has produced encouraging outcomes:1students were able to design, and simulate complex gate CMOS circuits using EDA tools, in the four(4 course electives identified for the track; 2 the culture of independent learning among students improvement in students soft skills, communication skills, time-management and teamwork skill,; 3. useof free and web-based tools overcome the issue of high cost of license for EDA tools and seminar/training for continuous upgrading of faculty. Another encouraging outcome was the acceptance of the student-centered teaching approach used, Problem-Based Learning (PBL,in enhancing the students learning experience.

Engine Tune-Up Service. Unit 1: Battery and Cranking System. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Goodson-Roberts, Ludy; And Others

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 1, Battery and Cranking System. Focus of the posttests is the testing of the battery and cranking system. Four multiple choice posttests are provided, one for each of the performance objectives contained in the unit. (No answer keys are provided.)…

Automotive mechatronics automotive networking, driving stability systems, electronics

CERN Document Server

2015-01-01

As the complexity of automotive vehicles increases this book presents operational and practical issues of automotive mechatronics. It is a comprehensive introduction to controlled automotive systems and provides detailed information of sensors for travel, angle, engine speed, vehicle speed, acceleration, pressure, temperature, flow, gas concentration etc. The measurement principles of the different sensor groups are explained and examples to show the measurement principles applied in different types. Contents Basics of mechatronics.- Architecture.- Electronic control unit.- Software development.- Basic principles of networking.- Automotive networking.- Bus systems.- Automotive sensors.- Sensor measuring principles.- Sensor types.- Electric actuators.- Electrohydraulic actuators.- Electronic transmission control.- Electronic transmission control unit.- Modules for transmission control.- Antilock braking system.- Traction control system.- Electronic stability program.- Automatic brake functions.- Hydraulic modu...

Fuelling regulation with Electronic fuel injection for small spark ignition engine using Fuzzy Logic

International Nuclear Information System (INIS)

Shah, S.R.; Sahir, M.H.

2004-01-01

The use of Electronic Control systems in automotive applications gives the design engineer greater control over various processes compared with mechanical methods Examples of such electronic control systems are Electronic Fuel Injection (EFI), Traction Control Systems (TCS) and Anti-lock Braking Systems (ABS). In addition, the development of inexpensive and fast microcontrollers has remarkably improve, performance of passive and active safety systems of automobiles, without causing excessive increase in prices of vehicles -a favourable factor from the consumer's perspective. This paper deals with a possible electronic aid for the improvement of power control in a motorcycle. Controlling the speed and power of a motorcycle is difficult; especially on bumpy and uneven terrain. In this paper, the development of an EPI system is discussed, incorporating artificial intelligence to regulate the fuel supplied to the engine. It would minimize wheel slippage and jerky and sudden acceleration which potentially dangerous. It would also reduce production of large quantities of pollutant like hydrocarbons and carbon monoxide. Fuel consumption would also improve during stop-and-go traffic. (author)

The Supply and Demand of Technology and Engineering Teachers in the United States: Who Knows?

Science.gov (United States)

Moye, Johnny J.

2017-01-01

The purpose of this study was to determine the supply and demand of technology and engineering teachers in the United States. Once gathered, the resulting data (that was available) was compared to previous studies to determine trends. The researcher reviewed the 2010-11 through 2015-16 Technology & Engineering Teacher Education Directories. To…

ASIL determination for motorbike's Electronics Throttle Control System (ETCS) mulfunction

Science.gov (United States)

Zaman Rokhani, Fakhrul; Rahman, Muhammad Taqiuddin Abdul; Ain Kamsani, Noor; Sidek, Roslina Mohd; Saripan, M. Iqbal; Samsudin, Khairulmizam; Khair Hassan, Mohd

2017-11-01

Electronics Throttle Control System (ETCS) is the principal electronic unit in all fuel injection engine motorbike, augmenting the engine performance efficiency in comparison to the conventional carburetor based engine. ETCS is regarded as a safety-critical component, whereby ETCS malfunction can cause unintended acceleration or deceleration event, which can be hazardous to riders. In this study, Hazard Analysis and Risk Assessment, an ISO26262 functional safety standard analysis has been applied on motorbike's ETCS to determine the required automotive safety integrity level. Based on the analysis, the established automotive safety integrity level can help to derive technical and functional safety measures for ETCS development.

Speed Control of General Purpose Engine with Electronic Governor

Science.gov (United States)

Sawut, Umerujan; Tohti, Gheyret; Takigawa, Buso; Tsuji, Teruo

This paper presents a general purpose engine speed control system with an electronic governor in order to improve the current system with a mechanical governor which shows unstable characteristics by change of mecanical friction or A/F ratio (Air/Fuel ratio). For the control system above, there are problems that the feedback signal is only a crank angle because of cost and the controlled object is a general purpose engine which is strongly nonlinear. In order to overcome these problems, the system model is shown for the dynamic estimation of the amount of air flow and the robust controller is designed. That is, the proposed system includes the robust sliding-mode controller by the feedback signal of only a crank angle where Genetic Algorithm is applied for the controller design. The simulation and the experiments by MATLAB/Simulink are performed to show the effectiveness of our proposal.

Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

Science.gov (United States)

Rios, Pedro; Stuart, Julie Ann; Grant, Ed

2003-12-01

Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

Preface: Special Topic on Frontiers in Molecular Scale Electronics

Science.gov (United States)

Evers, Ferdinand; Venkataraman, Latha

2017-03-01

The electronic, mechanical, and thermoelectric properties of molecular scale devices have fascinated scientists across several disciplines in natural sciences and engineering. The interest is partially technological, driven by the fast miniaturization of integrated circuits that now have reached characteristic features at the nanometer scale. Equally important, a very strong incentive also exists to elucidate the fundamental aspects of structure-function relations for nanoscale devices, which utilize molecular building blocks as functional units. Thus motivated, a rich research field has established itself, broadly termed "Molecular Electronics," that hosts a plethora of activities devoted to this goal in chemistry, physics, and electrical engineering. This Special Topic on Frontiers of Molecular Scale Electronics captures recent theoretical and experimental advances in the field.

An investigation of the performance of an electronic in-line pump system for diesel engines

Science.gov (United States)

Fan, Li-Yun; Zhu, Yuan-Xian; Long, Wu-Qiang; Ma, Xiu-Zhen; Xue, Ying-Ying

2008-12-01

WIT Electronic Fuel System Co., Ltd. has developed a new fuel injector, the Electronic In-line Pump (EIP) system, designed to meet China’s diesel engine emission and fuel economy regulations. It can be used on marine diesel engines and commercial vehicle engines through different EIP systems. A numerical model of the EIP system was built in the AMESim environment for the purpose of creating a design tool for engine application and system optimization. The model was used to predict key injection characteristics under different operating conditions, such as injection pressure, injection rate, and injection duration. To validate these predictions, experimental tests were conducted under the conditions that were modeled. The results were quite encouraging and in agreement with model predictions. Additional experiments were conducted to study the injection characteristics of the EIP system. These results show that injection pressure and injection quantity are insensitive to injection timing variations, this is due to the design of the constant velocity cam profile. Finally, injection quantity and pressure vs. pulse width at different cam speeds are presented, an important injection characteristic for EIP system calibration.

Engineering in-plane silicon nanowire springs for highly stretchable electronics

Science.gov (United States)

Xue, Zhaoguo; Dong, Taige; Zhu, Zhimin; Zhao, Yaolong; Sun, Ying; Yu, Linwei

2018-01-01

Crystalline silicon (c-Si) is unambiguously the most important semiconductor that underpins the development of modern microelectronics and optoelectronics, though the rigid and brittle nature of bulk c-Si makes it difficult to implement directly for stretchable applications. Fortunately, the one-dimensional (1D) geometry, or the line-shape, of Si nanowire (SiNW) can be engineered into elastic springs, which indicates an exciting opportunity to fabricate highly stretchable 1D c-Si channels. The implementation of such line-shape-engineering strategy demands both a tiny diameter of the SiNWs, in order to accommodate the strains under large stretching, and a precise growth location, orientation and path control to facilitate device integration. In this review, we will first introduce the recent progresses of an in-plane self-assembly growth of SiNW springs, via a new in-plane solid-liquid-solid (IPSLS) mechanism, where mono-like but elastic SiNW springs are produced by surface-running metal droplets that absorb amorphous Si thin film as precursor. Then, the critical growth control and engineering parameters, the mechanical properties of the SiNW springs and the prospects of developing c-Si based stretchable electronics, will be addressed. This efficient line-shape-engineering strategy of SiNW springs, accomplished via a low temperature batch-manufacturing, holds a strong promise to extend the legend of modern Si technology into the emerging stretchable electronic applications, where the high carrier mobility, excellent stability and established doping and passivation controls of c-Si can be well inherited. Project supported by the National Basic Research 973 Program (No. 2014CB921101), the National Natural Science Foundation of China (No. 61674075), the National Key Research and Development Program of China (No. 2017YFA0205003), the Jiangsu Excellent Young Scholar Program (No. BK20160020), the Scientific and Technological Support Program in Jiangsu Province (No. BE

Teaching Sustainable Energy and Power Electronics to Engineering Students in a Laboratory Environment Using Industry-Standard Tools

Science.gov (United States)

Ochs, David S.; Miller, Ruth Douglas

2015-01-01

Power electronics and renewable energy are two important topics for today's power engineering students. In many cases, the two topics are inextricably intertwined. As the renewable energy sector grows, the need for engineers qualified to design such systems grows as well. In order to train such engineers, new courses are needed that highlight the…

Use of the LITEE Lorn Manufacturing Case Study in a Senior Chemical Engineering Unit Operations Laboratory

Science.gov (United States)

Abraham, Nithin Susan; Abulencia, James Patrick

2011-01-01

This study focuses on the effectiveness of incorporating the Laboratory for Innovative Technology and Engineering Education (LITEE) Lorn Manufacturing case into a senior level chemical engineering unit operations course at Manhattan College. The purpose of using the case study is to demonstrate the relevance of ethics to chemical engineering…

Nanoscale Engineering in VO2 Nanowires via Direct Electron Writing Process.

Science.gov (United States)

Zhang, Zhenhua; Guo, Hua; Ding, Wenqiang; Zhang, Bin; Lu, Yue; Ke, Xiaoxing; Liu, Weiwei; Chen, Furong; Sui, Manling

2017-02-08

Controlling phase transition in functional materials at nanoscale is not only of broad scientific interest but also important for practical applications in the fields of renewable energy, information storage, transducer, sensor, and so forth. As a model functional material, vanadium dioxide (VO 2 ) has its metal-insulator transition (MIT) usually at a sharp temperature around 68 °C. Here, we report a focused electron beam can directly lower down the transition temperature of a nanoarea to room temperature without prepatterning the VO 2 . This novel process is called radiolysis-assisted MIT (R-MIT). The electron beam irradiation fabricates a unique gradual MIT zone to several times of the beam size in which the temperature-dependent phase transition is achieved in an extended temperature range. The gradual transformation zone offers to precisely control the ratio of metal/insulator phases. This direct electron writing technique can open up an opportunity to precisely engineer nanodomains of diversified electronic properties in functional material-based devices.

Does the Future Engineer Force Transition Engineer Units between Offensive and Stability Operations in Ways That Achieve Responsiveness, Versatility, Agility, Effectiveness, and Efficiency?

National Research Council Canada - National Science Library

London, David T

2005-01-01

.... The main question is as follows: Does the FEF transition engineer units between offensive and stability operations in ways that achieve responsiveness, versatility, agility, effectiveness, and efficiency...

Electronic digital computers their use in science and engineering

CERN Document Server

Alt, Franz L

1958-01-01

Electronic Digital Computers: Their Use in Science and Engineering describes the principles underlying computer design and operation. This book describes the various applications of computers, the stages involved in using them, and their limitations. The machine is composed of the hardware which is run by a program. This text describes the use of magnetic drum for storage of data and some computing. The functions and components of the computer include automatic control, memory, input of instructions by using punched cards, and output from resulting information. Computers operate by using numbe

Integrating Sustainability in a PBL Environment for Electronics Engineering

DEFF Research Database (Denmark)

Arsat, Mahyuddin; Holgaard, Jette Egelund; de Graaff, Erik

2013-01-01

(PBL) has been put forward as a promising pedagogical model and emerged as an opportunity to implement sustainability successfully. Due to the almost forty years of experience in PBL, a case study was carried out at Aalborg University, Denmark to excerpt their experience of integrating sustainability...... in a problem based learning environment. Three electronics engineering project modules were selected as example and empirically supported by constructed interviews with staff and document analysis of selected material. The findings were analysed with a systems approach and presented with reference to three...

Automotive systems engineering

Energy Technology Data Exchange (ETDEWEB)

Maurer, Markus [Technische Univ. Braunschweig (Germany). Inst. fuer Regelungstechnik; Winner, Hermann (eds.) [Technische Univ. Darmstadt (Germany). Fachgebiet Fahrzeugtechnik

2013-06-01

Innovative state-of-the-art book. Presents brand new results of a joint workshop in the field of automotive systems engineering. Recommendable to students for further reading even though not a primary text book. This book reflects the shift in design paradigm in automobile industry. It presents future innovations, often referred as ''automotive systems engineering''. These cause fundamental innovations in the field of driver assistance systems and electro-mobility as well as fundamental changes in the architecture of the vehicles. New driving functionalities can only be realized if the software programs of multiple electronic control units work together correctly. This volume presents the new and innovative methods which are mandatory to master the complexity of the vehicle of the future.

Test report: Electron-proton spectrometer qualification test unit, qualification test

Science.gov (United States)

Vincent, D. L.

1972-01-01

Qualification tests of the electron-proton spectrometer test unit are presented. The tests conducted were: (1) functional, (2) thermal/vacuum, (3) electromagnetic interference, (4) acoustic, (5) shock, (6) vibration, and (7) humidity. Results of each type of test are presented in the form of data sheets.

Engine Tune-Up Service. Unit 5: Fuel and Carburetion Systems. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Goodson, Ludy

This student guide is for Unit 5, Fuel and Carburetion Systems, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with inspecting and servicing the fuel and carburetion systems. A companion review exercise book and posttests are available separately as CE 031 218-219. An introduction tells how this unit fits…

Surviving the Lead Reliability Engineer Role in High Unit Value Projects

Science.gov (United States)

Perez, Reinaldo J.

2011-01-01

A project with a very high unit value within a company is defined as a project where a) the project constitutes one of a kind (or two-of-a-kind) national asset type of project, b) very large cost, and c) a mission failure would be a very public event that will hurt the company's image. The Lead Reliability engineer in a high visibility project is by default involved in all phases of the project, from conceptual design to manufacture and testing. This paper explores a series of lessons learned, over a period of ten years of practical industrial experience by a Lead Reliability Engineer. We expand on the concepts outlined by these lessons learned via examples. The lessons learned are applicable to all industries.

ELECTRONIC CONTROL FOR FUEL SUPPLY OF DIESEL ENGINE ON THE BASIS OF PROGRAMMABLE PID-REGULATOR

Directory of Open Access Journals (Sweden)

A. G. Bakhanovich

2017-01-01

Full Text Available The article presents a schematic diagram of the Euro-3 diesel engine electronic control and describes hard- and software platform of the high pressure fuel pump pneumatic actuator control that allows to realize the concept of electronic fuel supply control of diesel engine KamAZ-740. The strategic dependence beetwen the angular position of fuel pump governor lever and the angular position of electronic accelerator pedal were put on the basis of electronic control concept. Implementation of this dependence was carried out by applying a modulated PWM signal with determined duty cycle by the controller to the coil proportional solenoid valve, which is responsible for the amount of air pressure in the working chamber of the power air cylinder, connected by articulated-type to the governor lever of the high pressure fuel pump. In this case, the feedback control by position of governor lever of the high pressure fuel pump was introduced in the control circuit, but engine crankshaft speed control was carried out using a software continuous PID governor. Developed strategy gives possibility to track the deflection  of control parameter from a predetermined value by real-time and almost instantly, to make a control action on actuators to eliminate this deflection, while providing a minimum time of transition. Governor’s setting (proportional, integral and differential component performed empirically using the classical Ziegler – Nichols method, based on the analysis of the safety factor of automatic control system. The results of calculating the coefficients of proportional integral-differential regulator and oscillograms HIL experiment on testing the proposed diesel engine throttle control strategies using visualization CoDeSys V2.3 are given in activity.

Cryogenic Propellant Storage and Transfer Engineering Development Unit Hydrogen Tank

Science.gov (United States)

Werkheiser, Arthur

2015-01-01

The Cryogenic Propellant Storage and Transfer (CPST) project has been a long-running program in the Space Technology Mission Directorate to enhance the knowledge and technology related to handling cryogenic propellants, specifically liquid hydrogen. This particular effort, the CPST engineering development unit (EDU), was a proof of manufacturability effort in support of a flight article. The EDU was built to find and overcome issues related to manufacturability and collect data to anchor the thermal models for use on the flight design.

Employability of the Bachelor of Science in Electronics Engineering Graduates of Camarines Sur Polytechnic Colleges

Directory of Open Access Journals (Sweden)

Rizza T. Loquias

2015-11-01

Full Text Available The study determined the employment status of the graduates of BS Electronics Engineering from 1999 to 2011. It also addressed the relevance of the ECE program outcomes and school factors to their employability. Pertinent data were gathered using a questionnaire and the sample size of 180 was determined using Slovin’s formula. Findings revealed that the graduates are highly employable in a wide range of industry such as electronics manufacturing, electronics design, telecommunications, broadcasting, and data communications and ICT-related areas, were able to pass the licensure examinations and other certifications, currently enjoying regular permanent job positions as supervisors, production engineers, process engineers, educators and others, and are working for companies located in Metro Manila and industrial zones in Laguna and Cavite. A significant number work abroad as OFWs. Only a small number are employed in the province of Camarines Sur mainly due to the lack of electronics industries and employment opportunities in the area. The skills the graduates found most useful to their first jobs are critical thinking, problem solving, and communication skills. Suggestions were given such as the inclusion of industry-utilized software and enhancement of the OJT program, more hands-on activities in the curriculum, exposure to industry while studying, and job familiarization among others. The findings of the study can serve as basis for curriculum review and revision to meet the demands of the industry.

Common Principles of Molecular Electronics and Nanoscale Electrochemistry.

Science.gov (United States)

Bueno, Paulo Roberto

2018-05-24

The merging of nanoscale electronics and electrochemistry can potentially modernize the way electronic devices are currently engineered or constructed. It is well known that the greatest challenges will involve not only miniaturizing and improving the performance of mobile devices, but also manufacturing reliable electrical vehicles, and engineering more efficient solar panels and energy storage systems. These are just a few examples of how technological innovation is dependent on both electrochemical and electronic elements. This paper offers a conceptual discussion of this central topic, with particular focus on the impact that uniting physical and chemical concepts at a nanoscale could have on the future development of electroanalytical devices. The specific example to which this article refers pertains to molecular diagnostics, i.e., devices that employ physical and electrochemical concepts to diagnose diseases.

3D-Printing Crystallographic Unit Cells for Learning Materials Science and Engineering

Science.gov (United States)

Rodenbough, Philip P.; Vanti, William B.; Chan, Siu-Wai

2015-01-01

Introductory materials science and engineering courses universally include the study of crystal structure and unit cells, which are by their nature highly visual 3D concepts. Traditionally, such topics are explored with 2D drawings or perhaps a limited set of difficult-to-construct 3D models. The rise of 3D printing, coupled with the wealth of…

Projecting potential adoption of genetically engineered freeze-tolerant Eucalyptus in the United States

Science.gov (United States)

David N. Wear; Ernest Dixon IV; Robert C. Abt; Navinder Singh

2015-01-01

Development of commercial Eucalyptus plantations has been limited in the United States because of the species’ sensitivity to freezing temperatures. Recently developed genetically engineered clones of a Eucalyptus hybrid, which confer freeze tolerance, could expand the range of commercial plantations. This study explores how...

Design of a microprocessor-based Control, Interface and Monitoring (CIM unit for turbine engine controls research

Science.gov (United States)

Delaat, J. C.; Soeder, J. F.

1983-01-01

High speed minicomputers were used in the past to implement advanced digital control algorithms for turbine engines. These minicomputers are typically large and expensive. It is desirable for a number of reasons to use microprocessor-based systems for future controls research. They are relatively compact, inexpensive, and are representative of the hardware that would be used for actual engine-mounted controls. The Control, Interface, and Monitoring Unit (CIM) contains a microprocessor-based controls computer, necessary interface hardware and a system to monitor while it is running an engine. It is presently being used to evaluate an advanced turbofan engine control algorithm.

Engineering tradeoffs in miniaturization of electronics for very large detectors

International Nuclear Information System (INIS)

Larsen, R.S.

1987-10-01

The trend toward Application-Specific Integrated Circuits and similar systems-on-a-chip-technologies is fueling a new wave of innovation in detector electronics, just in time to address some of the problems being introduced by detectors which will approach a million channels of electronics. The cost-effectiveness of these technologies can be easily demonstrated, and the trend of the past twenty years of achieving more powerful electronics at a lower per-channel cost should receive a major impetus. The investment required in the new technologies will reshape the work force of most laboratories, by providing more and better tools, and by requiring training or retraining of significant numbers of personnel. The need for new instrumentation standards will arise at new levels in the detectors of the future. The laboratories must also invest heavily in integrating various computer aided engineering and computer aided design tools into a smoothly functioning system. They must also establish a new and different kind of working relationship with vendors and suppliers of both basic devices as well as standard packaged products. This paper discusses three concepts

Two Rotor Stratified Charge Rotary Engine (SCRE) Engine System Technology Evaluation

Science.gov (United States)

Hoffman, T.; Mack, J.; Mount, R.

1994-01-01

This report summarizes results of an evaluation of technology enablement component technologies as integrated into a two rotor Stratified Charge Rotary Engine (SCRE). The work constitutes a demonstration of two rotor engine system technology, utilizing upgraded and refined component technologies derived from prior NASA Contracts NAS3-25945, NAS3-24628 and NAS-23056. Technical objectives included definition of, procurement and assembly of an advanced two rotor core aircraft engine, operation with Jet-A fuel at Take-Off rating of 340 BHP (254kW) and operation at a maximum cruise condition of 255 BHP (190kW), 75% cruise. A fuel consumption objective of 0.435 LBS/BHP-Hr (265 GRS/kW-Hr) was identified for the maximum cruise condition. A critical technology component item, a high speed, unit injector fuel injection system with electronic control was defined, procured and tested in conjunction with this effort. The two rotor engine configuration established herein defines an affordable, advanced, Jet-A fuel capability core engine (not including reduction gear, propeller shaft and some aircraft accessories) for General Aviation of the mid-1990's and beyond.

Query Log Analysis of an Electronic Health Record Search Engine

Science.gov (United States)

Yang, Lei; Mei, Qiaozhu; Zheng, Kai; Hanauer, David A.

2011-01-01

We analyzed a longitudinal collection of query logs of a full-text search engine designed to facilitate information retrieval in electronic health records (EHR). The collection, 202,905 queries and 35,928 user sessions recorded over a course of 4 years, represents the information-seeking behavior of 533 medical professionals, including frontline practitioners, coding personnel, patient safety officers, and biomedical researchers for patient data stored in EHR systems. In this paper, we present descriptive statistics of the queries, a categorization of information needs manifested through the queries, as well as temporal patterns of the users’ information-seeking behavior. The results suggest that information needs in medical domain are substantially more sophisticated than those that general-purpose web search engines need to accommodate. Therefore, we envision there exists a significant challenge, along with significant opportunities, to provide intelligent query recommendations to facilitate information retrieval in EHR. PMID:22195150

Plasmonic engineering of metal-oxide nanowire heterojunctions in integrated nanowire rectification units

Energy Technology Data Exchange (ETDEWEB)

Lin, Luchan; Zhou, Y. Norman, E-mail: liulei@tsinghua.edu.cn, E-mail: nzhou@uwaterloo.ca [Department of Mechanical Engineering, State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Centre for Advanced Materials Joining, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Zou, Guisheng; Liu, Lei, E-mail: liulei@tsinghua.edu.cn, E-mail: nzhou@uwaterloo.ca [Department of Mechanical Engineering, State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Duley, Walt W. [Centre for Advanced Materials Joining, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Department of Physics and Astronomy, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada)

2016-05-16

We show that irradiation with femtosecond laser pulses can produce robust nanowire heterojunctions in coupled non-wetting metal-oxide Ag-TiO{sub 2} structures. Simulations indicate that joining arises from the effect of strong plasmonic localization in the region of the junction. Strong electric field effects occur in both Ag and TiO{sub 2} resulting in the modification of both surfaces and an increase in wettability of TiO{sub 2}, facilitating the interconnection of Ag and TiO{sub 2} nanowires. Irradiation leads to the creation of a thin layer of highly defected TiO{sub 2} in the contact region between the Ag and TiO{sub 2} nanowires. The presence of this layer allows the formation of a heterojunction and offers the possibility of engineering the electronic characteristics of interfacial structures. Rectifying junctions with single and bipolar properties have been generated in Ag-TiO{sub 2} nanowire circuits incorporating asymmetrical and symmetrical interfacial structures, respectively. This fabrication technique should be applicable for the interconnection of other heterogeneous metal-oxide nanowire components and demonstrates that femtosecond laser irradiation enables interfacial engineering for electronic applications of integrated nanowire structures.

Plasmonic engineering of metal-oxide nanowire heterojunctions in integrated nanowire rectification units

Science.gov (United States)

Lin, Luchan; Zou, Guisheng; Liu, Lei; Duley, Walt W.; Zhou, Y. Norman

2016-05-01

We show that irradiation with femtosecond laser pulses can produce robust nanowire heterojunctions in coupled non-wetting metal-oxide Ag-TiO2 structures. Simulations indicate that joining arises from the effect of strong plasmonic localization in the region of the junction. Strong electric field effects occur in both Ag and TiO2 resulting in the modification of both surfaces and an increase in wettability of TiO2, facilitating the interconnection of Ag and TiO2 nanowires. Irradiation leads to the creation of a thin layer of highly defected TiO2 in the contact region between the Ag and TiO2 nanowires. The presence of this layer allows the formation of a heterojunction and offers the possibility of engineering the electronic characteristics of interfacial structures. Rectifying junctions with single and bipolar properties have been generated in Ag-TiO2 nanowire circuits incorporating asymmetrical and symmetrical interfacial structures, respectively. This fabrication technique should be applicable for the interconnection of other heterogeneous metal-oxide nanowire components and demonstrates that femtosecond laser irradiation enables interfacial engineering for electronic applications of integrated nanowire structures.

Nuclear electronics laboratory manual

International Nuclear Information System (INIS)

1984-05-01

The Nuclear Electronics Laboratory Manual is a joint product of several electronics experts who have been associated with IAEA activity in this field for many years. The manual does not include experiments of a basic nature, such as characteristics of different active electronics components. It starts by introducing small electronics blocks, employing one or more active components. The most demanding exercises instruct a student in the design and construction of complete circuits, as used in commercial nuclear instruments. It is expected that a student who completes all the experiments in the manual should be in a position to design nuclear electronics units and also to understand the functions of advanced commercial instruments which need to be repaired or maintained. The future tasks of nuclear electronics engineers will be increasingly oriented towards designing and building the interfaces between a nuclear experiment and a computer. The manual pays tribute to this development by introducing a number of experiments which illustrate the principles and the technology of interfacing

Performance and Environmental Test Results of the High Voltage Hall Accelerator Engineering Development Unit

Science.gov (United States)

Kamhawi, Hani; Haag, Thomas; Huang, Wensheng; Shastry, Rohit; Pinero, Luis; Peterson, Todd; Mathers, Alex

2012-01-01

NASA Science Mission Directorate's In-Space Propulsion Technology Program is sponsoring the development of a 3.5 kW-class engineering development unit Hall thruster for implementation in NASA science and exploration missions. NASA Glenn and Aerojet are developing a high fidelity high voltage Hall accelerator that can achieve specific impulse magnitudes greater than 2,700 seconds and xenon throughput capability in excess of 300 kilograms. Performance, plume mappings, thermal characterization, and vibration tests of the high voltage Hall accelerator engineering development unit have been performed. Performance test results indicated that at 3.9 kW the thruster achieved a total thrust efficiency and specific impulse of 58%, and 2,700 sec, respectively. Thermal characterization tests indicated that the thruster component temperatures were within the prescribed material maximum operating temperature limits during full power thruster operation. Finally, thruster vibration tests indicated that the thruster survived the 3-axes qualification full-level random vibration test series. Pre and post-vibration test performance mappings indicated almost identical thruster performance. Finally, an update on the development progress of a power processing unit and a xenon feed system is provided.

Engine Tune-up Service. Unit 6: Emission Control Systems. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Morse, David T.; May, Theodore R.

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 6, Emission Control Systems, available separately as CE 031 220. Focus of the posttests is inspecting, testing, and servicing emission control systems. One multiple choice posttest is provided that covers the seven performance objectives contained in…

Engine Tune-Up Service. Unit 1: Battery and Cranking System. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Goodson-Roberts, Ludy; And Others

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 1, Battery and Cranking System. Focus of the exercises and pretests is testing the battery and cranking system. Pretests and performance checklists are provided for each of the four performance objectives contained in the unit.…

Electron-phonon interaction and scattering in Si and Ge: Implications for phonon engineering

International Nuclear Information System (INIS)

Tandon, Nandan; Albrecht, J. D.; Ram-Mohan, L. R.

2015-01-01

We report ab-initio results for electron-phonon (e-ph) coupling and display the existence of a large variation in the coupling parameter as a function of electron and phonon dispersion. This variation is observed for all phonon modes in Si and Ge, and we show this for representative cases where the initial electron states are at the band gap edges. Using these e-ph matrix elements, which include all possible phonon modes and electron bands within a relevant energy range, we evaluate the imaginary part of the electron self-energy in order to obtain the associated scattering rates. The temperature dependence is seen through calculations of the scattering rates at 0 K and 300 K. The results provide a basis for understanding the impacts of phonon scattering vs. orientation and geometry in the design of devices, and in analysis of transport phenomena. This provides an additional tool for engineering the transfer of energy from carriers to the lattice

Synthetic biology and metabolic engineering.

Science.gov (United States)

Stephanopoulos, Gregory

2012-11-16

Metabolic engineering emerged 20 years ago as the discipline occupied with the directed modification of metabolic pathways for the microbial synthesis of various products. As such, it deals with the engineering (design, construction, and optimization) of native as well as non-natural routes of product synthesis, aided in this task by the availability of synthetic DNA, the core enabling technology of synthetic biology. The two fields, however, only partially overlap in their interest in pathway engineering. While fabrication of biobricks, synthetic cells, genetic circuits, and nonlinear cell dynamics, along with pathway engineering, have occupied researchers in the field of synthetic biology, the sum total of these areas does not constitute a coherent definition of synthetic biology with a distinct intellectual foundation and well-defined areas of application. This paper reviews the origins of the two fields and advances two distinct paradigms for each of them: that of unit operations for metabolic engineering and electronic circuits for synthetic biology. In this context, metabolic engineering is about engineering cell factories for the biological manufacturing of chemical and pharmaceutical products, whereas the main focus of synthetic biology is fundamental biological research facilitated by the use of synthetic DNA and genetic circuits.

Engineering embedded systems physics, programs, circuits

CERN Document Server

Hintenaus, Peter

2015-01-01

This is a textbook for graduate and final-year-undergraduate computer-science and electrical-engineering students interested in the hardware and software aspects of embedded and cyberphysical systems design. It is comprehensive and self-contained, covering everything from the basics to case-study implementation. Emphasis is placed on the physical nature of the problem domain and of the devices used. The reader is assumed to be familiar on a theoretical level with mathematical tools like ordinary differential equation and Fourier transforms. In this book these tools will be put to practical use. Engineering Embedded Systems begins by addressing basic material on signals and systems, before introducing to electronics. Treatment of digital electronics accentuating synchronous circuits and including high-speed effects proceeds to micro-controllers, digital signal processors and programmable logic. Peripheral units and decentralized networks are given due weight. The properties of analog circuits and devices like ...

The Application of Advanced Technique of Fan Frame Unit on High Bypass Ratio Aero Engine

Directory of Open Access Journals (Sweden)

Hou Peng

2017-01-01

Full Text Available High bypass ratio aero-engine was widely used on military and civil aviation domain, as the power of larger aircraft. Fan frame unit was the main bearing frame of high bypass ratio aero-engine, which composed of strut, HUB MID BOX and external bypass parts. Resin/composite was used on external bypass parts(acoustic liner, containment ring, fan outlet guide vane and fan case skin fillets, which not only reduced the weight and manufacturing cost, but also improved the noise absorption, containment and anti-fatigue ability of engine. The design of composite was becoming a key technique for high bypass ratio aero-engine. In special test of the core engine, nitrogen cooling system was designed to cool the cavity of spool. The nitrogen pipeline passed through the inner cavity of fan frame, then inserted into NO. 3 bearing seal, so nitrogen gas was sent into the cavity of core engine spool. On high bypass ratio aero-engine, the external bypass and fan frame inner cavity were the design platform for advanced technique, such as composite and pipeline system, and also provided guarantee for reliable operation of engine.

Propulsion Control Technology Development in the United States A Historical Perspective

Science.gov (United States)

Jaw, Link C.a; Garg, Sanjay

2005-01-01

This paper presents a historical perspective of the advancement of control technologies for aircraft gas turbine engines. The paper primarily covers technology advances in the United States in the last 60 years (1940 to approximately 2002). The paper emphasizes the pioneering technologies that have been tested or implemented during this period, assimilating knowledge and experience from industry experts, including personal interviews with both current and retired experts. Since the first United States-built aircraft gas turbine engine was flown in 1942, engine control technology has evolved from a simple hydro-mechanical fuel metering valve to a full-authority digital electronic control system (FADEC) that is common to all modern aircraft propulsion systems. At the same time, control systems have provided engine diagnostic functions. Engine diagnostic capabilities have also evolved from pilot observation of engine gauges to the automated on-board diagnostic system that uses mathematical models to assess engine health and assist in post-flight troubleshooting and maintenance. Using system complexity and capability as a measure, we can break the historical development of control systems down to four phases: (1) the start-up phase (1942 to 1949), (2) the growth phase (1950 to 1969), (3) the electronic phase (1970 to 1989), and (4) the integration phase (1990 to 2002). In each phase, the state-of-the-art control technology is described and the engines that have become historical landmarks, from the control and diagnostic standpoint, are identified. Finally, a historical perspective of engine controls in the last 60 years is presented in terms of control system complexity, number of sensors, number of lines of software (or embedded code), and other factors.

Mockup Didatic Set for Students Development in Automotive Electronic

Directory of Open Access Journals (Sweden)

Fabio Delatore

2013-05-01

Full Text Available The automotive engineering education area, specifically on internal combustion engine, requires the use of suitable systems, capable to simulate, test and obtain specifics data from its operation. Automotive engines are so complex due to it is a mix of engineering subjects, so, a mockup was created to help its study. The mockup is an exactly the same engine that equips a vehicle, but assembled in a mechanical base, equipped with all the necessary components for running it up. The objective of this work is to develop a mockup with a suitable Electronic Control Unit (ECU board, in order to obtain the sensors/actuators signals from the engine and control some important engine functions by using an external ECU, so that the students may test their own strategies, compare with the original ECU.

76 FR 82279 - Electronic Delivery of Search Results From the United States Patent and Trademark Office to the...

Science.gov (United States)

2011-12-30

...] Electronic Delivery of Search Results From the United States Patent and Trademark Office to the European... United States Patent and Trademark Office (USPTO) has recently begun electronic delivery of search... the search results from a previously filed patent application to which the European patent application...

Validation of a zero-dimensional model for prediction of NOx and engine performance for electronically controlled marine two-stroke diesel engines

International Nuclear Information System (INIS)

Scappin, Fabio; Stefansson, Sigurður H.; Haglind, Fredrik; Andreasen, Anders; Larsen, Ulrik

2012-01-01

The aim of this paper is to derive a methodology suitable for energy system analysis for predicting the performance and NO x emissions of marine low speed diesel engines. The paper describes a zero-dimensional model, evaluating the engine performance by means of an energy balance and a two zone combustion model using ideal gas law equations over a complete crank cycle. The combustion process is divided into intervals, and the product composition and flame temperature are calculated in each interval. The NO x emissions are predicted using the extended Zeldovich mechanism. The model is validated using experimental data from two MAN B and W engines; one case being data subject to engine parameter changes corresponding to simulating an electronically controlled engine; the second case providing data covering almost all model input and output parameters. The first case of validation suggests that the model can predict specific fuel oil consumption and NO x emissions within the 95% confidence intervals given by the experimental measurements. The second validation confirms the capability of the model to match measured engine output parameters based on measured engine input parameters with a maximum 5% deviation. - Highlights: ► A fast realistic model of a marine two-stroke low speed diesel engine was derived. ► The model is fast and accurate enough for future complex energy systems analysis. ► The effects of engine tuning were validated with experimental tests. ► The model was validated while constrained by experimental input and output data.

Near Earth Asteroid Scout Solar Sail Engineering Development Unit Test Suite

Science.gov (United States)

Lockett, Tiffany Russell; Few, Alexander; Wilson, Richard

2017-01-01

The Near Earth Asteroid (NEA) Scout project is a 6U reconnaissance mission to investigate a near Earth asteroid utilizing an 86m(sub 2) solar sail as the primary propulsion system. This will be the largest solar sail NASA has launched to date. NEA Scout is currently manifested on the maiden voyage of the Space Launch System in 2018. In development of the solar sail subsystem, design challenges were identified and investigated for packaging within a 6U form factor and deployment in cis-lunar space. Analysis was able to capture understanding of thermal, stress, and dynamics of the stowed system as well as mature an integrated sail membrane model for deployed flight dynamics. Full scale system testing on the ground is the optimal way to demonstrate system robustness, repeatability, and overall performance on a compressed flight schedule. To physically test the system, the team developed a flight sized engineering development unit with design features as close to flight as possible. The test suite included ascent vent, random vibration, functional deployments, thermal vacuum, and full sail deployments. All of these tests contributed towards development of the final flight unit. This paper will address several of the design challenges and lessons learned from the NEA Scout solar sail subsystem engineering development unit. Testing on the component level all the way to the integrated subsystem level. From optical properties of the sail material to fold and spooling the single sail, the team has developed a robust deployment system for the solar sail. The team completed several deployments of the sail system in preparation for flight at half scale (4m) and full scale (6.8m): boom only, half scale sail deployment, and full scale sail deployment. This paper will also address expected and received test results from ascent vent, random vibration, and deployment tests.

Use of EGS4 codes system for the evaluation of electron contamination in telecobalt therapy unit

International Nuclear Information System (INIS)

Bernal, B.; Alfonso, R.

1995-01-01

The cobalt 60 beams employed radiotherapy usually have some electron contamination, mainly depending on the selected field size, the diaphragm-skin distance and the collation system features. The electron component of a thyratron 780C cobalt unit was evaluated, using in any material and geometry, by using Monte Carlo techniques. The radiation transport in the unit head was simulated, as well as the absorbed dose in a water phantom, so the surface dose fraction due to electron was computed. Measurements from 0 to 5 mm depth were carried out in order to confirm our calculations, finding good agreement with them. Several PMMA filters with different thickness were analyzed to study their role in the electron contamination reduction; an optimal thickness around 5 mm was found

Structural and electronic properties of in-plane phase engineered WSe2: A DFT study

Science.gov (United States)

Bhart, Ankush; Kapoor, Pooja; Sharma, Munish; Sharma, Raman; Ahluwalia, P. K.

2018-04-01

We present first principal investigations on structural and electronic properties of in-plane phase engineered WSe2 with armchair type interface. The 2H and 1T phases of WSe2, joined along x-direction is a natural metal-semiconductor heterostructure and therefore shows potential for applications in 2D electronics and opto-electronics. The electronic properties transit towards metallic 1T region. No inflections across interface shows negligible mismatch strain which is unlike what has been reported for MoS2. Charge density analysis shows charge accumulation on 1T domain. This can lead to reduction of Schottky barrier heights at the metal-semiconductor junction. STM analysis confirms transition of 1T phase towards distorted 1T' structure. The present results provide essential insights for nano-devices using 2D hybrid materials.

Engineering assessment of inactive uranium mill tailings: Phillips/United Nuclear site, Ambrosia Lake, New Mexico

International Nuclear Information System (INIS)

1981-10-01

Ford, Bacon and Davis Utah, Inc., has reevaluated the Phillips/United Nuclear site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Ambrosia Lake, New Mexico. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from 2.6 million dry tons of tailings at the Phillips/United Nuclear site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The four alternative actions presented in this engineering assessment range from millsite decontamination with the addition of 3 m of stabilization cover material, to removal of the tailings to remote disposal sites and decontamination of the tailings site. Cost estimates for the four options range from about $21,500,000 for stabilization in-place, to about $45,200,000 for disposal at a distance of about 15 mi. Three principal alternatives for the reprocessing of the Phillips/United Nuclear tailings were examined: heap leaching; treatment at an existing mill; and reprocessing at a new conventional mill constructed for tailings reprocessing.The cost of the uranium recovered would be about $87/lb of U 3 O 8 by either heap leach or conventional plant process. The spot market price for uranium was $25/lb early in 1981. Reprocessing the Phillips/United Nuclear tailings for uranium recovery does not appear to be economically attractive under present or foreseeable market conditions

A general purpose diagnostic technique for marine diesel engines - Application on the main propulsion and auxiliary diesel units of a marine vessel

International Nuclear Information System (INIS)

Lamaris, V.T.; Hountalas, D.T.

2010-01-01

Diesel engines are widely used in marine applications (i.e. propulsion and auxiliaries) except from a few cases where gas or steam turbines are used. This is the result of their high efficiency, power concentration and reliability compared to other compatible or alternative power sources. The proper and efficient operation of the engines (main engine and diesel generator units) in marine applications is critical, and therefore techniques or systems that determine engine current condition and detect potential faults are extremely important. Furthermore, it is advantageous when such techniques can be applied on different engine configurations and provide reliable results, because on a vessel usually exist diesel engines of different type, i.e. the main propulsion unit is a large low-speed two-stroke diesel engine while the diesel generators are four-stroke medium or high speed engines. In the present work is described and evaluated for the first time the application of an improved diagnostic technique, developed by the authors, on both the main engine and the auxiliary units of a commercial marine vessel. The diagnostic technique is based on a thermodynamic simulation model. The simulation model embedded in the technique has been modified, namely an existing two-zone model is replaced by a multi-zone one. With this modification it is avoided model constant tuning with the operating conditions. This is extremely important for the diagnostic philosophy of the proposed technique. Using data from engine shop tests, the simulation model is calibrated (i.e. model constants are determined) and the engine reference condition is obtained. The simulation model is then used to estimate the current engine condition, using field measurements (i.e. cylinder pressure measurements, periphery data, etc.). From the results it is revealed that the diagnosis method provides detailed information for the operating condition of both engines and the values of parameters that cannot be

Mechanical engineering science in SI units

CERN Document Server

Gwyther, J L; Williams, G

1970-01-01

0.1 Mechanical Engineering Science covers various fundamental concepts that are essential in the practice of mechanical engineering. The title is comprised of 19 chapters that detail various topics, including chemical and physical laws. The coverage of the book includes Newtonian laws, mechanical energy, friction, stress, and gravity. The text also discusses the chemical aspects of mechanical engineering, which include gas laws, states of matter, and fuel combustion. The last chapter tackles concerns in laboratory experiments. The book will be of great use to students of mechanical eng

Engineering electronic states of periodic and quasiperiodic chains by buckling

Science.gov (United States)

Mukherjee, Amrita; Nandy, Atanu; Chakrabarti, Arunava

2017-07-01

The spectrum of spinless, non-interacting electrons on a linear chain that is buckled in a non-uniform, quasiperiodic manner is investigated within a tight binding formalism. We have addressed two specific cases, viz., a perfectly periodic chain wrinkled in a quasiperiodic Fibonacci pattern, and a quasiperiodic Fibonacci chain, where the buckling also takes place in a Fibonacci pattern. The buckling brings distant neighbors in the parent chain to close proximity, which is simulated by a tunnel hopping amplitude. It is seen that, in the perfectly ordered case, increasing the strength of the tunnel hopping (that is, bending the segments more) absolutely continuous density of states is retained towards the edges of the band, while the central portion becomes fragmented and host subbands of narrowing widths containing extended, current carrying states, and multiple isolated bound states formed as a result of the bending. A switching ;on; and ;off; of the electronic transmission can thus be engineered by buckling. On the other hand, in the second example of a quasiperiodic Fibonacci chain, imparting a quasiperiodic buckling is found to generate continuous subband(s) destroying the usual multifractality of the energy spectrum. We present exact results based on a real space renormalization group analysis, that is corroborated by explicit calculation of the two terminal electronic transport.

Practical electronics handbook

CERN Document Server

Sinclair, Ian R

2013-01-01

Practical Electronics Handbook, Third Edition provides the frequently used and highly applicable principles of electronics and electronic circuits.The book contains relevant information in electronics. The topics discussed in the text include passive and active discrete components; linear and digital I.C.s; microprocessors and microprocessor systems; digital-analogue conversions; computer aids in electronics design; and electronic hardware components.Electronic circuit constructors, service engineers, electronic design engineers, and anyone with an interest in electronics will find the book ve

Design and Development of the Engine Unit for a Twin-Rotor Unmanned Aerial Vehicle

Directory of Open Access Journals (Sweden)

G. Avanzini

2005-01-01

Full Text Available Advanced computer-aided technologies played a crucial role in the design of an unconventional Uninhabited Aerial Vehicle (UAV, developed at the Turin Technical University and the University of Rome “La Sapienza”. The engine unit of the vehicle is made of a complex system of three two stroke piston engines coupled with two counter-rotating three-bladed rotors, controlled by rotary PWM servos. The focus of the present paper lies on the enabling technologies exploited in the framework of activities aimed at designing a suitable and reliable engine system, capable of performing the complex tasks required for operating the proposed rotorcraft. The synergic use of advanced computational tools for estimating the aerodynamic performance of the vehicle, solid modeling for mechanical components design, and rapid prototyping techniques for control system logic synthesis and implementation will be presented. 

Engine Tune-Up Service. Unit 3: Primary Circuit. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 3, Primary Circuit, available separately as CE 031 211. Focus of the exercises and pretests is testing the primary ignition circuit. Pretests and performance checklists are provided for each of the eight performance objectives…

Engine Tune-up Service. Unit 2: Charging System. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Richardson, Roger L.; Bacon, E. Miles

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 2, Charging System, available separately as CE 031 208. Focus of the exercises and pretests is testing the charging system. Pretests and performance checklists are provided for each of the three performance objectives contained in…

Engine Tune-up Service. Unit 4: Secondary Circuit. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 4, Secondary Circuit, available separately as CE 031 214. Focus of the exercises and pretests is testing and servicing the secondary ignition circuit. Pretests and performance checklists are provided for each of the seven…

Engine Tune-Up Service. Unit 5: Fuel and Carburetion Systems. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Morse, David T.

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 5, Fuel and Carburetion Systems; available separately as CE 031 217. Focus of the posttests is the inspecting and servicing of the fuel and carburetion systems. One multiple choice posttest is provided that covers the 10 performance objectives…

A Low Cost Implementation of an Existing Hands-on Laboratory Experiment in Electronic Engineering

Directory of Open Access Journals (Sweden)

Clement Onime

2014-10-01

Full Text Available In engineering the pedagogical content of most formative programmes includes a significant amount of practical laboratory hands-on activity designed to deliver knowledge acquisition from actual experience alongside traditional face-to-face classroom based lectures and tutorials; this hands-on aspect is not always adequately addressed by current e-learning platforms. An innovative approach to e-learning in engineering, named computer aided engineering education (CAEE is about the use of computer aids for the enhanced, interactive delivery of educational materials in different fields of engineering through two separate but related components; one for classroom and another for practical hands-on laboratory work. The component for hands-on laboratory practical work focuses on the use of mixed reality (video-based augmented reality tools on mobile devices/platforms. This paper presents the computer aided engineering education (CAEE implementation of a laboratory experiment in micro-electronics that highlights some features such as the ability to closely implement an existing laboratory based hands-on experiment with lower associated costs and the ability to conduct the experiment off-line while maintaining existing pedagogical contents and standards.

Fundamental of biomedical engineering

CERN Document Server

Sawhney, GS

2007-01-01

About the Book: A well set out textbook explains the fundamentals of biomedical engineering in the areas of biomechanics, biofluid flow, biomaterials, bioinstrumentation and use of computing in biomedical engineering. All these subjects form a basic part of an engineer''s education. The text is admirably suited to meet the needs of the students of mechanical engineering, opting for the elective of Biomedical Engineering. Coverage of bioinstrumentation, biomaterials and computing for biomedical engineers can meet the needs of the students of Electronic & Communication, Electronic & Instrumenta

A theoretical study on the performances of thermoelectric heat engine and refrigerator with two-dimensional electron reservoirs

International Nuclear Information System (INIS)

Luo, Xiaoguang; Long, Kailin; Wang, Jun; Qiu, Teng; He, Jizhou; Liu, Nian

2014-01-01

Theoretical thermoelectric nanophysics models of low-dimensional electronic heat engine and refrigerator devices, comprising two-dimensional hot and cold reservoirs and an interconnecting filtered electron transport mechanism have been established. The models were used to numerically simulate and evaluate the thermoelectric performance and energy conversion efficiencies of these low-dimensional devices, based on three different types of electron transport momentum-dependent filters, referred to herein as k x , k y , and k r filters. Assuming the Fermi-Dirac distribution of electrons, expressions for key thermoelectric performance parameters were derived for the resonant transport processes, in which the transmission of electrons has been approximated as a Lorentzian resonance function. Optimizations were carried out and the corresponding optimized design parameters have been determined, including but not limited to the universal theoretical upper bound of the efficiency at maximum power for heat engines, and the maximum coefficient of performance for refrigerators. From the results, it was determined that k r filter delivers the best thermoelectric performance, followed by the k x filter, and then the k y filter. For refrigerators with any one of three filters, an optimum range for the full width at half maximum of the transport resonance was found to be B T.

Unit cell-based computer-aided manufacturing system for tissue engineering

International Nuclear Information System (INIS)

Kang, Hyun-Wook; Park, Jeong Hun; Kang, Tae-Yun; Seol, Young-Joon; Cho, Dong-Woo

2012-01-01

Scaffolds play an important role in the regeneration of artificial tissues or organs. A scaffold is a porous structure with a micro-scale inner architecture in the range of several to several hundreds of micrometers. Therefore, computer-aided construction of scaffolds should provide sophisticated functionality for porous structure design and a tool path generation strategy that can achieve micro-scale architecture. In this study, a new unit cell-based computer-aided manufacturing (CAM) system was developed for the automated design and fabrication of a porous structure with micro-scale inner architecture that can be applied to composite tissue regeneration. The CAM system was developed by first defining a data structure for the computing process of a unit cell representing a single pore structure. Next, an algorithm and software were developed and applied to construct porous structures with a single or multiple pore design using solid freeform fabrication technology and a 3D tooth/spine computer-aided design model. We showed that this system is quite feasible for the design and fabrication of a scaffold for tissue engineering. (paper)

Unit cell-based computer-aided manufacturing system for tissue engineering.

Science.gov (United States)

Kang, Hyun-Wook; Park, Jeong Hun; Kang, Tae-Yun; Seol, Young-Joon; Cho, Dong-Woo

2012-03-01

Scaffolds play an important role in the regeneration of artificial tissues or organs. A scaffold is a porous structure with a micro-scale inner architecture in the range of several to several hundreds of micrometers. Therefore, computer-aided construction of scaffolds should provide sophisticated functionality for porous structure design and a tool path generation strategy that can achieve micro-scale architecture. In this study, a new unit cell-based computer-aided manufacturing (CAM) system was developed for the automated design and fabrication of a porous structure with micro-scale inner architecture that can be applied to composite tissue regeneration. The CAM system was developed by first defining a data structure for the computing process of a unit cell representing a single pore structure. Next, an algorithm and software were developed and applied to construct porous structures with a single or multiple pore design using solid freeform fabrication technology and a 3D tooth/spine computer-aided design model. We showed that this system is quite feasible for the design and fabrication of a scaffold for tissue engineering.

Advancing cognitive engineering methods to support user interface design for electronic health records.

Science.gov (United States)

Thyvalikakath, Thankam P; Dziabiak, Michael P; Johnson, Raymond; Torres-Urquidy, Miguel Humberto; Acharya, Amit; Yabes, Jonathan; Schleyer, Titus K

2014-04-01

Despite many decades of research on the effective development of clinical systems in medicine, the adoption of health information technology to improve patient care continues to be slow, especially in ambulatory settings. This applies to dentistry as well, a primary care discipline with approximately 137,000 practitioners in the United States. A critical reason for slow adoption is the poor usability of clinical systems, which makes it difficult for providers to navigate through the information and obtain an integrated view of patient data. In this study, we documented the cognitive processes and information management strategies used by dentists during a typical patient examination. The results will inform the design of a novel electronic dental record interface. We conducted a cognitive task analysis (CTA) study to observe ten general dentists (five general dentists and five general dental faculty members, each with more than two years of clinical experience) examining three simulated patient cases using a think-aloud protocol. Dentists first reviewed the patient's demographics, chief complaint, medical history and dental history to determine the general status of the patient. Subsequently, they proceeded to examine the patient's intraoral status using radiographs, intraoral images, hard tissue and periodontal tissue information. The results also identified dentists' patterns of navigation through patient's information and additional information needs during a typical clinician-patient encounter. This study reinforced the significance of applying cognitive engineering methods to inform the design of a clinical system. Second, applying CTA to a scenario closely simulating an actual patient encounter helped with capturing participants' knowledge states and decision-making when diagnosing and treating a patient. The resultant knowledge of dentists' patterns of information retrieval and review will significantly contribute to designing flexible and task

Elucidating the electron transport in semiconductors via Monte Carlo simulations: an inquiry-driven learning path for engineering undergraduates

International Nuclear Information System (INIS)

Adorno, Dominique Persano; Pizzolato, Nicola; Fazio, Claudio

2015-01-01

Within the context of higher education for science or engineering undergraduates, we present an inquiry-driven learning path aimed at developing a more meaningful conceptual understanding of the electron dynamics in semiconductors in the presence of applied electric fields. The electron transport in a nondegenerate n-type indium phosphide bulk semiconductor is modelled using a multivalley Monte Carlo approach. The main characteristics of the electron dynamics are explored under different values of the driving electric field, lattice temperature and impurity density. Simulation results are presented by following a question-driven path of exploration, starting from the validation of the model and moving up to reasoned inquiries about the observed characteristics of electron dynamics. Our inquiry-driven learning path, based on numerical simulations, represents a viable example of how to integrate a traditional lecture-based teaching approach with effective learning strategies, providing science or engineering undergraduates with practical opportunities to enhance their comprehension of the physics governing the electron dynamics in semiconductors. Finally, we present a general discussion about the advantages and disadvantages of using an inquiry-based teaching approach within a learning environment based on semiconductor simulations. (paper)

Elucidating the electron transport in semiconductors via Monte Carlo simulations: an inquiry-driven learning path for engineering undergraduates

Science.gov (United States)

Persano Adorno, Dominique; Pizzolato, Nicola; Fazio, Claudio

2015-09-01

Within the context of higher education for science or engineering undergraduates, we present an inquiry-driven learning path aimed at developing a more meaningful conceptual understanding of the electron dynamics in semiconductors in the presence of applied electric fields. The electron transport in a nondegenerate n-type indium phosphide bulk semiconductor is modelled using a multivalley Monte Carlo approach. The main characteristics of the electron dynamics are explored under different values of the driving electric field, lattice temperature and impurity density. Simulation results are presented by following a question-driven path of exploration, starting from the validation of the model and moving up to reasoned inquiries about the observed characteristics of electron dynamics. Our inquiry-driven learning path, based on numerical simulations, represents a viable example of how to integrate a traditional lecture-based teaching approach with effective learning strategies, providing science or engineering undergraduates with practical opportunities to enhance their comprehension of the physics governing the electron dynamics in semiconductors. Finally, we present a general discussion about the advantages and disadvantages of using an inquiry-based teaching approach within a learning environment based on semiconductor simulations.

Dosimetric accuracy at low monitor unit setting in electron beams at different dose rates

International Nuclear Information System (INIS)

Ravikumar, M.; Ravichandran, R.; Supe, Sanjay S.; Sharma, Anil K.

1999-01-01

As electron beam with low monitor unit (LMU) settings are used in some dosimetric studies, better understanding of accuracy in dose delivery at LMU setting is necessary. The dose measurements were carried out with 0.6 cm 3 farmer type ion chamber at d max in a polystyrene phantom. Measurements at different MUs show that the dose linearity ratio (DLR) increases as the MU setting decreases below 20 MU and DLRs are found to increase when the incident electron beams have higher energies. The increase in DLR is minimum for low dose rate setting for all five electron beam energies (6, 9, 12, 16 and 20 MeV). As the variation in dose delivery is machine-specific, a detailed study should be conducted before the low MU setting is implemented. Since errors in dose delivery are high at higher dose rates, low dose rate may be better at low MU unit setting. (author)

Defence electronics industry profile, 1990-1991

Science.gov (United States)

The defense electronics industry profiled in this review comprises an estimated 150 Canadian companies that develop, manufacture, and repair radio and communications equipment, radars for surveillance and navigation, air traffic control systems, acoustic and infrared sensors, computers for navigation and fire control, signal processors and display units, special-purpose electronic components, and systems engineering and associated software. Canadian defense electronics companies generally serve market niches and end users of their products are limited to the military, government agencies, or commercial airlines. Geographically, the industry is concentrated in Ontario and Quebec, where about 91 percent of the industry's production and employment is found. In 1989, the estimated revenue of the industry was $2.36 billion, and exports totalled an estimated $1.4 billion. Strengths and weaknesses of the industry are discussed in terms of such factors as the relatively small size of Canadian companies, the ability of Canadian firms to access research and development opportunities and export markets in the United States, the dependence on foreign-made components, and international competition.

Sublimator Driven Coldplate Engineering Development Unit Test Results

Science.gov (United States)

Sheth, Rubik B.; Stephan, Ryan A.; Leimkuehler, Thomas O.

2010-01-01

The Sublimator Driven Coldplate (SDC) is a unique piece of thermal control hardware that has several advantages over a traditional thermal control scheme. The principal advantage is the possible elimination of a pumped fluid loop, potentially increasing reliability and reducing complexity while saving both mass and power. Because the SDC requires a consumable feedwater, it can only be used for short mission durations. Additionally, the SDC is ideal for a vehicle with small transport distances and low heat rejection requirements. An SDC Engineering Development Unit was designed and fabricated. Performance tests were performed in a vacuum chamber to quantify and assess the performance of the SDC. The test data was then used to develop correlated thermal math models. Nonetheless, an Integrated Sublimator Driven Coldplate (ISDC) concept is being developed. The ISDC couples a coolant loop with the previously described SDC hardware. This combination allows the SDC to be used as a traditional coldplate during long mission phases and provides for dissimilar system redundancy

Electronic Nose Technology and its Applications

Directory of Open Access Journals (Sweden)

Esmaeil MAHMOUDI

2009-08-01

Full Text Available In the past decade, Electronic Nose instrumentation has generated much interest internationally for its potential to solve a wide variety of problems in fragrance and cosmetics production, food and beverages manufacturing, chemical engineering, environmental monitoring and more recently medical diagnostic, bioprocesses and clinical diagnostic plant diseases. This instrument measure electrical resistance changes generated by adsorption of volatiles to the surface of electro active- polymer coated sensor- unique digital electronic fingerprint of aroma derived from multi-sensor- responses to distinct mixture of microbial volatiles. Major advances in information and gas sensor technology could enhance the diagnostic power of future bio-electronic nose and facilitate global surveillance mode of disease control and management. Several dozen companies are now designed and selling electronic nose units globally for a wide variety of expending markets. The present review includes principles of electronic nose technology, biosensor structure and applications of electronic nose in many fields.

Engineering evaluation/conceptual plan for the 200-UP-1 groundwater operable unit interim remedial measure

International Nuclear Information System (INIS)

Myers, D.A.; Swanson, L.C.; Weeks, R.S.; Giacinto, J.; Gustafson, F.W.; Ford, B.H.; Wittreich, C.; Parnell, S.; Green, J.

1995-04-01

This report presents an engineering evaluation and conceptual plan for an interim remedial measure (ERM) to address a uranium and technetium-99 groundwater plume and an associated nitrate contamination plume in the 200-UP-1 Groundwater Operable Unit located in the 200 West Area of the Hanford Site. This report provides information regarding the need and potentially achievable objectives and goals for an IRM and evaluates alternatives to contain elevated concentrations of uranium, technetium-99, nitrate, and carbon tetrachloride and to obtain information necessary to develop final remedial actions for the operable unit

Quantitative evaluation of flexibility in undergraduate engineering curricula in the United Arab Emirates

Directory of Open Access Journals (Sweden)

Naif A. Darwish

2016-03-01

Full Text Available In academia, smooth progression of students significantly depends on the way curricula are developed and organized. Curricula or study plans with high degree of interconnectivity between courses, multiple prerequisites, and hierarchically structured courses tend to complicate the smooth progress of the enrolled students. In this work, a rigorous quantitative relaxation indicator, developed and published elsewhere by the first author, has been applied to quantify the degree of stiffness and rigidity in undergraduate engineering curricula at the American University of Sharjah (AUS, the University of Sharjah (UOS, United Arab Emirates University (UAEU, and the Petroleum Institute (PI, which are the leading universities in the United Arab Emirates. Results indicate high rigidity (low relaxation indices due to high degree of interconnectivity between courses, specifically in the second year of the study plans. The chemical engineering curriculum at PI exhibited the least flexibility due to very strong pre-and-co-requisite ties while the civil & environmental curriculum at UAEU showed the highest flexibility. The curricula considered require immediate attention and reorganization in order to facilitate smooth sequential progress of the students from one semester to another. A list of courses that require relaxation of strong pre-and corequisites ties has been presented for each curriculum.

METHOD OF CONVERSION OF HIGH- AND MIDDLE-SPEED DIESEL ENGINES INTO GAS DIESEL ENGINES

Directory of Open Access Journals (Sweden)

Mikhail G. Shatrov

2017-12-01

Full Text Available The paper aims at the development of fuel supply and electronic control systems for boosted high- and middle-speed transport engines. A detailed analysis of different ways of converting diesel engine to operate on natural gas was carried out. The gas diesel process with minimized ignition portion of diesel fuel injected by the Common Rail (CR system was selected. Electronic engine control and modular gas feed systems which can be used both on high- and middle-speed gas diesel engines were developed. Also diesel CR fuel supply systems were developed in cooperation with the industrial partner, namely, those that can be mounted on middle-speed diesel and gas diesel engines. Electronic control and gas feed systems were perfected using modeling and engine tests. The high-speed diesel engine was converted into a gas diesel one. After perfection of the gas feed and electronic control systems, bench tests of the high-speed gas diesel engine were carried out showing a high share of diesel fuel substitution with gas, high fuel efficiency and significant decrease of NOх and СО2 emissions.

Nuclear engineering education in the United States: The first 50 years

International Nuclear Information System (INIS)

Brown, G.

2004-01-01

Full text: This paper will discuss recent trends in the nuclear engineering education infrastructure in the United States. In the last several years political, economic and technical issues have been addressed and nuclear technology appears poised to resume growing again. It is in this new environment that there has been a confluence of industry, government and academic interests to see that nuclear engineering education retains its vitality and ability to provide technological leadership and a well-educated workforce. In order to understand the current situation it is important to give a brief historical perspective covering the six decades since the inception of 'Atoms for Peace' in 1953. The passage of the Atomic Energy Act of 1954 established the Atomic Energy Commission and the declassification of much nuclear technology and scientific material. There was an understandable optimistic outlook as to the potential for nuclear technology in the areas of power, medicine and other industrial and scientific applications. There were commercial concepts for using nuclear energy to power ships, planes, rockets, and cars. But the must successful application, by far was in the area of electric power production. In only a few years demonstration nuclear power plants were built and the infamous quote - 'two cheap to meter' was reported. In the following decade much progress was made and commercial plant orders increased substantially in number and in size. There were going to light water reactors, gas cooled reactors, liquid metal fast reactors, reprocessing, waste buried in salt mines. There was going to be 'a 1000 reactors in the year 2000'. This was the picture in the United States in the 50's and 60's. And it was in this environment that nuclear engineering education was birthed and grew. The first nuclear engineering academic programs and university research reactors were established in the 1950's at such places as North Carolina State, MIT, Penn State and others

Electronic monitoring and voice prompts improve hand hygiene and decrease nosocomial infections in an intermediate care unit.

Science.gov (United States)

Swoboda, Sandra M; Earsing, Karen; Strauss, Kevin; Lane, Stephen; Lipsett, Pamela A

2004-02-01

To determine whether electronic monitoring of hand hygiene and voice prompts can improve hand hygiene and decrease nosocomial infection rates in a surgical intermediate care unit. Three-phase quasi-experimental design. Phase I was electronic monitoring and direct observation; phase II was electronic monitoring and computerized voice prompts for failure to perform hand hygiene on room exit; and phase III was electronic monitoring only. Nine-room, 14-bed intermediate care unit in a university, tertiary-care institution. All patient rooms, utility room, and staff lavatory were monitored electronically. All healthcare personnel including physicians, nurses, nursing support personnel, ancillary staff, all visitors and family members, and any other personnel interacting with patients on the intermediate care unit. All patients with an intermediate care unit length of stay >48 hrs were followed for nosocomial infection. Electronic monitoring during all phases, computerized voice prompts during phase II only. We evaluated a total of 283,488 electronically monitored entries into a patient room with 251,526 exits for 420 days (10,080 hrs and 3,549 patient days). Compared with phase I, hand hygiene compliance in patient rooms improved 37% during phase II (odds ratio, 1.38; 95% confidence interval, 1.04-1.83) and 41% in phase III (odds ratio, 1.41; 95% confidence interval, 1.07-1.84). When adjusting for patient admissions during each phase, point estimates of nosocomial infections decreased by 22% during phase II and 48% during phase III; when adjusting for patient days, the number of infections decreased by 10% during phase II and 40% during phase III. Although the overall rate of nosocomial infections significantly decreased when combining phases II and III, the association between nosocomial infection and individual phase was not significant. Electronic monitoring provided effective ongoing feedback about hand hygiene compliance. During both the voice prompt phase and post

Modeling, simulation, parametric study and economic assessment of reciprocating internal combustion engine integrated with multi-effect desalination unit

International Nuclear Information System (INIS)

Salimi, Mohsen; Amidpour, Majid

2017-01-01

Highlights: • Integration of small MED unit with gas engine power cycle is studied in this paper. • Modeling, simulation, parametric study and sensitivity analysis were performed. • A thermodynamic model for heat recovery and power generation of the gas engine has been presented. • Annualized Cost of System (ACS) has been employed for economic assessment. • Economic feasibilty dependence of integrated system on natural gas and water prices has been investigated. - Abstract: Due to thermal nature of multi-effect desalination (MED), its integration with a suitable power cycle is highly desirable for waste heat recovery. One of the proper power cycle for proposed integration is internal combustion engine (ICE). The exhaust gas heat of ICE is used to produce motive steam for the required heat for the first effect of MED system. Also, the water jacket heat is utilized in a heat exchanger to pre-heat the seawater. This paper studies a thermodynamic model for a tri-generation system composed of ICE integrated with MED. The ICE thermodynamic model has been used in place of different empirical efficiency relations to estimate performance – load curves reasonably. The entire system performance has been coded in MATLAB, and the results of proposed thermodynamic model for the engine have been verified by manufacturer catalogue. By increasing the engine load from 40% to 100%, the water production of MED unit will increase from 4.38 cubic meters per day to 26.78 cubic meters per day and the tri-generation efficiency from 31% to 56%. Economic analyses of the MED unit integrated with ICE was performed based on Annualized Cost of System method. This integration makes the system more economical. It has been determined that in higher market prices for fresh water (more than 7 US$ per cubic meter), the increase in effects number is more significant to the period of return decrement.

Supporting information retrieval from electronic health records: A report of University of Michigan's nine-year experience in developing and using the Electronic Medical Record Search Engine (EMERSE).

Science.gov (United States)

Hanauer, David A; Mei, Qiaozhu; Law, James; Khanna, Ritu; Zheng, Kai

2015-06-01

This paper describes the University of Michigan's nine-year experience in developing and using a full-text search engine designed to facilitate information retrieval (IR) from narrative documents stored in electronic health records (EHRs). The system, called the Electronic Medical Record Search Engine (EMERSE), functions similar to Google but is equipped with special functionalities for handling challenges unique to retrieving information from medical text. Key features that distinguish EMERSE from general-purpose search engines are discussed, with an emphasis on functions crucial to (1) improving medical IR performance and (2) assuring search quality and results consistency regardless of users' medical background, stage of training, or level of technical expertise. Since its initial deployment, EMERSE has been enthusiastically embraced by clinicians, administrators, and clinical and translational researchers. To date, the system has been used in supporting more than 750 research projects yielding 80 peer-reviewed publications. In several evaluation studies, EMERSE demonstrated very high levels of sensitivity and specificity in addition to greatly improved chart review efficiency. Increased availability of electronic data in healthcare does not automatically warrant increased availability of information. The success of EMERSE at our institution illustrates that free-text EHR search engines can be a valuable tool to help practitioners and researchers retrieve information from EHRs more effectively and efficiently, enabling critical tasks such as patient case synthesis and research data abstraction. EMERSE, available free of charge for academic use, represents a state-of-the-art medical IR tool with proven effectiveness and user acceptance. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Theory of semiconductor junction devices a textbook for electrical and electronic engineers

CERN Document Server

Leck, J H

1967-01-01

Theory of Semiconductor Junction Devices: A Textbook for Electrical and Electronic Engineers presents the simplified numerical computation of the fundamental electrical equations, specifically Poisson's and the Hall effect equations. This book provides the fundamental theory relevant for the understanding of semiconductor device theory. Comprised of 10 chapters, this book starts with an overview of the application of band theory to the special case of semiconductors, both intrinsic and extrinsic. This text then describes the electrical properties of conductivity, semiconductors, and Hall effe

Accelerated Electromechanical Modeling of a Distributed Internal Combustion Engine Generator Unit

Directory of Open Access Journals (Sweden)

Serhiy V. Bozhko

2012-07-01

Full Text Available Distributed generation with a combustion engine prime mover is still widely used to supply electric power in a variety of applications. These applications range from backup power supply systems and combined wind-diesel generation to providing power in places where grid connection is either technically impractical or financially uneconomic. Modelling of such systems as a whole is extremely difficult due to the long-time load profiles needed and the computational difficulty of including small time-constant electrical dynamics with large time-constant mechanical dynamics. This paper presents the development of accelerated, reduced-order models of a distributed internal combustions engine generator unit. Overall these models are shown to achieve a massive improvement in the computational time required for long-time simulations while also achieving an extremely high level of dynamic accuracy. It is demonstrated how these models are derived, used and verified against benchmark models created using established techniques. Throughout the paper the modelling set as a whole, including multi level detail, is presented, detailed and finally summarised into a crucial tool for general system investigation and multiple target optimisation.

Magnetic collimation of fast electrons in specially engineered targets irradiated by ultraintense laser pulses

International Nuclear Information System (INIS)

Cai Hongbo; Zhu Shaoping; Wu Sizhong; Chen Mo; Zhou Cangtao; He, X. T.; Yu Wei; Nagatomo, Hideo

2011-01-01

The efficient magnetic collimation of fast electron flow transporting in overdense plasmas is investigated with two-dimensional collisional particle-in-cell numerical simulations. It is found that the specially engineered targets exhibiting either high-resistivity-core-low-resistivity-cladding structure or low-density-core-high-density-cladding structure can collimate fast electrons. Two main mechanisms to generate collimating magnetic fields are found. In high-resistivity-core-low-resistivity-cladding structure targets, the magnetic field at the interfaces is generated by the gradients of the resistivity and fast electron current, while in low-density-core-high-density-cladding structure targets, the magnetic field is generated by the rapid changing of the flow velocity of the background electrons in transverse direction (perpendicular to the flow velocity) caused by the density jump. The dependences of the maximal magnetic field on the incident laser intensity and plasma density, which are studied by numerical simulations, are supported by our analytical calculations.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT VII, ENGINE TUNE-UP--DETROIT DIESEL ENGINE.

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF TUNE-UP PROCEDURES FOR DIESEL ENGINES. TOPICS ARE SCHEDULING TUNE-UPS, AND TUNE-UP PROCEDURES. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING FILM "ENGINE TUNE-UP--DETROIT DIESEL ENGINE" AND OTHER MATERIALS. SEE VT 005 655 FOR FURTHER INFORMATION.…

[Integration of fundamental and applied medical and technical research made at the department of the biomedical systems, Moscow State Institute of Electronic Engineering].

Science.gov (United States)

Selishchev, S V

2004-01-01

The integration results of fundamental and applied medical-and-technical research made at the chair of biomedical systems, Moscow state institute of electronic engineering (technical university--MSIEE), are described in the paper. The chair is guided in its research activity by the traditions of higher education in Russia in the field of biomedical electronics and biomedical engineering. Its activities are based on the extrapolation of methods of electronic tools, computer technologies, physics, biology and medicine with due respect being paid to the requirements of practical medicine and to topical issues of research and design.

Engine Tune-up Service. Unit 6: Emission Control Systems. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 6, Emission Control Systems, available separately as CE 031 220. Focus of the exercises and pretests is inspecting, testing, and servicing emission control systems. Pretests and performance checklists are provided for each of the…

Draft audit report, human factors engineering control room design review: Saint Lucie Nuclear Power Plant, Unit No. 2

International Nuclear Information System (INIS)

Peterson, L.R.; Lappa, D.A.; Moore, J.W.

1981-01-01

A human factors engineering preliminary design review of the Saint Lucie Unit 2 control room was performed at the site on August 3 through August 7, 1981. This design review was carried out by a team from the Human Factors Engineering Branch, Division of Human Factors Safety. This report was prepared on the basis of the HFEB's review of the applicant's Preliminary Design Assessment and the human factors engineering design review/audit performed at the site. The review team included human factors consultants from BioTechnology, Inc., Falls Church, Virginia, and from Lawrence Livermore National Laboratory (University of California), Livermore, California

Phase engineering of monolayer transition-metal dichalcogenide through coupled electron doping and lattice deformation

International Nuclear Information System (INIS)

Ouyang, Bin; Lan, Guoqiang; Song, Jun; Guo, Yinsheng; Mi, Zetian

2015-01-01

First-principles calculations were performed to investigate the phase stability and transition within four monolayer transition-metal dichalcogenide (TMD) systems, i.e., MX 2 (M = Mo or W and X = S or Se) under coupled electron doping and lattice deformation. With the lattice distortion and electron doping density treated as state variables, the energy surfaces of different phases were computed, and the diagrams of energetically preferred phases were constructed. These diagrams assess the competition between different phases and predict conditions of phase transitions for the TMDs considered. The interplay between lattice deformation and electron doping was identified as originating from the deformation induced band shifting and band bending. Based on our findings, a potential design strategy combining an efficient electrolytic gating and a lattice straining to achieve controllable phase engineering in TMD monolayers was demonstrated

Mechanical engineering

CERN Document Server

Darbyshire, Alan

2010-01-01

Alan Darbyshire's best-selling text book provides five-star high quality content to a potential audience of 13,000 engineering students. It explains the most popular specialist units of the Mechanical Engineering, Manufacturing Engineering and Operations & Maintenance Engineering pathways of the new 2010 BTEC National Engineering syllabus. This challenging textbook also features contributions from specialist lecturers, ensuring that no stone is left unturned.

Process engineering design of pathological waste incinerator with an integrated combustion gases treatment unit.

Science.gov (United States)

Shaaban, A F

2007-06-25

Management of medical wastes generated at different hospitals in Egypt is considered a highly serious problem. The sources and quantities of regulated medical wastes have been thoroughly surveyed and estimated (75t/day from governmental hospitals in Cairo). From the collected data it was concluded that the most appropriate incinerator capacity is 150kg/h. The objective of this work is to develop the process engineering design of an integrated unit, which is technically and economically capable for incinerating medical wastes and treatment of combustion gases. Such unit consists of (i) an incineration unit (INC-1) having an operating temperature of 1100 degrees C at 300% excess air, (ii) combustion-gases cooler (HE-1) generating 35m(3)/h hot water at 75 degrees C, (iii) dust filter (DF-1) capable of reducing particulates to 10-20mg/Nm(3), (iv) gas scrubbers (GS-1,2) for removing acidic gases, (v) a multi-tube fixed bed catalytic converter (CC-1) to maintain the level of dioxins and furans below 0.1ng/Nm(3), and (vi) an induced-draft suction fan system (SF-1) that can handle 6500Nm(3)/h at 250 degrees C. The residence time of combustion gases in the ignition, mixing and combustion chambers was found to be 2s, 0.25s and 0.75s, respectively. This will ensure both thorough homogenization of combustion gases and complete destruction of harmful constituents of the refuse. The adequate engineering design of individual process equipment results in competitive fixed and operating investments. The incineration unit has proved its high operating efficiency through the measurements of different pollutant-levels vented to the open atmosphere, which was found to be in conformity with the maximum allowable limits as specified in the law number 4/1994 issued by the Egyptian Environmental Affairs Agency (EEAA) and the European standards.

Electronic structure description of the cis-MoOS unit in models for molybdenum hydroxylases.

Science.gov (United States)

Doonan, Christian J; Rubie, Nick D; Peariso, Katrina; Harris, Hugh H; Knottenbelt, Sushilla Z; George, Graham N; Young, Charles G; Kirk, Martin L

2008-01-09

The molybdenum hydroxylases catalyze the oxidation of numerous aromatic heterocycles and simple organics and, unlike other hydroxylases, utilize water as the source of oxygen incorporated into the product. The electronic structures of the cis-MoOS units in CoCp2[TpiPrMoVOS(OPh)] and TpiPrMoVIOS(OPh) (TpiPr = hydrotris(3-isopropylpyrazol-1-yl)borate), new models for molybdenum hydroxylases, have been studied in detail using S K-edge X-ray absorption spectroscopy, vibrational spectroscopy, and detailed bonding calculations. The results show a highly delocalized Mo=S pi* LUMO redox orbital that is formally Mo(dxy) with approximately 35% sulfido ligand character. Vibrational spectroscopy has been used to quantitate Mo-Ssulfido bond order changes in the cis-MoOS units as a function of redox state. Results support a redox active molecular orbital that has a profound influence on MoOS bonding through changes to the relative electro/nucleophilicity of the terminal sulfido ligand accompanying oxidation state changes. The bonding description for these model cis-MoOS systems supports enzyme mechanisms that are under orbital control and dominantly influenced by the unique electronic structure of the cis-MoOS site. The electronic structure of the oxidized enzyme site is postulated to play a role in polarizing a substrate carbon center for nucleophilic attack by metal activated water and acting as an electron sink in the two-electron oxidation of substrates.

Music engineering

CERN Document Server

Brice, Richard

2001-01-01

Music Engineering is a hands-on guide to the practical aspects of electric and electronic music. It is both a compelling read and an essential reference guide for anyone using, choosing, designing or studying the technology of modern music. The technology and underpinning science are introduced through the real life demands of playing and recording, and illustrated with references to well known classic recordings to show how a particular effect is obtained thanks to the ingenuity of the engineer as well as the musician. In addition, an accompanying companion website containing over 50 specially chosen tracks for download, provides practical demonstrations of the effects and techniques described in the book. Written by a music enthusiast and electronic engineer, this book covers the electronics and physics of the subject as well as the more subjective aspects. The second edition includes an updated Digital section including MPEG3 and fact sheets at the end of each chapter to summarise the key electronics and s...

Electronic Engineering Notebook: A software environment for research execution, documentation and dissemination

Science.gov (United States)

Moerder, Dan

1994-01-01

The electronic engineering notebook (EEN) consists of a free form research notebook, implemented in a commercial package for distributed hypermedia, which includes utilities for graphics capture, formatting and display of LaTex constructs, and interfaces to the host operating system. The latter capability consists of an information computer-aided software engineering (CASE) tool and a means to associate executable scripts with source objects. The EEN runs on Sun and HP workstations. The EEN, in day-to-day use can be used in much the same manner as the sort of research notes most researchers keep during development of projects. Graphics can be pasted in, equations can be entered via LaTex, etc. In addition, the fact that the EEN is hypermedia permits easy management of 'context', e.g., derivations and data can contain easily formed links to other supporting derivations and data. The CASE tool also permits development and maintenance of source code directly in the notebook, with access to its derivations and data.

Electronic structures and band gaps of chains and sheets based on phenylacetylene units

International Nuclear Information System (INIS)

Kondo, Masakazu; Nozaki, Daijiro; Tachibana, Masamitsu; Yumura, Takashi; Yoshizawa, Kazunari

2005-01-01

We investigate the electronic structures of polymers composed of π-conjugated phenylacetylene (PA) units, m-PA-based and p-PA-based wires, at the extended Hueckel level of theory. It is demonstrated that these conjugated systems should have a variety of electric conductance. All of the one-dimensional (1D) chains and the two-dimensional (2D) sheet based on the m-PA unit are insulators with large band gaps of 2.56 eV because there is no effective orbital interaction with neighboring chains. On the other hand, p-PA-based 1D chains have relatively small band gaps that decrease with an increase in chain width (1.17-1.74 eV) and are semiconductive. The p-PA-based sheet called 'graphyne', a 2D-limit of the p-PA-based 1D chains, shows a small band gap of 0.89 eV. The variety of band electronic structures is discussed in terms of frontier crystal orbitals

Test-Driven, Model-Based Systems Engineering

DEFF Research Database (Denmark)

Munck, Allan

Hearing systems have evolved over many years from simple mechanical devices (horns) to electronic units consisting of microphones, amplifiers, analog filters, loudspeakers, batteries, etc. Digital signal processors replaced analog filters to provide better performance end new features. Central....... This thesis concerns methods for identifying, selecting and implementing tools for various aspects of model-based systems engineering. A comprehensive method was proposed that include several novel steps such as techniques for analyzing the gap between requirements and tool capabilities. The method...... was verified with good results in two case studies for selection of a traceability tool (single-tool scenario) and a set of modeling tools (multi-tool scenarios). Models must be subjected to testing to allow engineers to predict functionality and performance of systems. Test-first strategies are known...

Pilot-Scale Laboratory Instruction for Chemical Engineering: The Specific Case of the Pilot-Unit Leading Group

Science.gov (United States)

Billet, Anne-Marie; Camy, Severine; Coufort-Saudejaud, Carole

2010-01-01

This paper presents an original approach for Chemical Engineering laboratory teaching that is currently applied at INP-ENSIACET (France). This approach, referred to as "pilot-unit leading group" is based on a partial management of the laboratories by the students themselves who become temporarily in charge of one specific laboratory. In…

Electronic structure characterization and bandgap engineering of solar hydrogen materials

International Nuclear Information System (INIS)

Guo, Jinghua

2007-01-01

Bandgap, band edge positions as well as the overall band structure of semiconductors are of crucial importance in photoelectrochemical and photocatalytic applications. The energy position of the band edge level can be controlled by the electronegativity of the dopants, the pH of the solution (flatband potential variation of 60 mV per pH unit), as well as by quantum confinement effects. Accordingly, band edges and bandgap can be tailored to achieve specific electronic, optical or photocatalytic properties. Synchrotron radiation with photon energy at or below 1 keV is giving new insight into such areas as condensed matter physics and extreme ultraviolet optics technology. In the soft x-ray region, the question tends to be, what are the electrons doing as they migrated between the atoms. In this paper, I will present a number of soft x-ray spectroscopic study of nanostructured 3d metal compounds Fe 2 O 3 and ZnO

NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 61: The Technical Communications Practices of ESL Aerospace Engineering Students in the United States: Results of a National Survey

Science.gov (United States)

Webb, John R.; Pinelli, Thomas E.; Barclay, Rebecca O.; Kennedy, John M.

1997-01-01

When engineering students graduate and enter the world of work, they make the transition from an academic to a professional community of knowledge. The importance of oral and written communication to the professional success and advancement of engineers is well documented. For example, studies such as those conducted by Mailloux (1989) indicate that communicating data, information, and knowledge takes up as much as 80% of an engineer's time. However, these same studies also indicate that many engineering graduates cannot (a) write technical reports that effectively inform and influence decisionmaking, (b) present their ideas persuasively, and (c) communicate with their peers. If these statements are true, how is learning to communicate effectively in their professional knowledge community different for engineering students educated in the United States but who come from other cultures-cultures in which English is not the primary language of communication? Answering this question requires adequate and generalizable data about these students' communications abilities, skills, and competencies. To contribute to the answer, we undertook a national (mail) survey of 1,727 student members of the American Institute of Aeronautics and Astronautics (AIAA). The focus of our analysis and this paper is a comparison of the responses of 297 student members for whom English is a second language with the responses of 1,430 native English speaking students to queries regarding career choice, bilingualism and language fluency, communication skills, collaborative writing, computer use, and the use of electronic (computer) networks.

Engineering Mixed Ionic Electronic Conduction in La 0.8 Sr 0.2 MnO 3+ δ Nanostructures through Fast Grain Boundary Oxygen Diffusivity

KAUST Repository

Saranya, Aruppukottai M.; Pla, Dolors; Morata, Alex; Cavallaro, Andrea; Canales-Vá zquez, Jesú s; Kilner, John A.; Burriel, Mó nica; Tarancó n, Albert

2015-01-01

to implement in nanostructures. Here, an artificial mixed ionic electronic conducting oxide is fabricated by grain boundary (GB) engineering thin films of La0.8Sr0.2MnO3+δ. This electronic conductor is converted into a good mixed ionic electronic conductor

Implementation and use of cloud-based electronic lab notebook in a bioprocess engineering teaching laboratory.

Science.gov (United States)

Riley, Erin M; Hattaway, Holly Z; Felse, P Arthur

2017-01-01

Electronic lab notebooks (ELNs) are better equipped than paper lab notebooks (PLNs) to handle present-day life science and engineering experiments that generate large data sets and require high levels of data integrity. But limited training and a lack of workforce with ELN knowledge have restricted the use of ELN in academic and industry research laboratories which still rely on cumbersome PLNs for recordkeeping. We used LabArchives, a cloud-based ELN in our bioprocess engineering lab course to train students in electronic record keeping, good documentation practices (GDPs), and data integrity. Implementation of ELN in the bioprocess engineering lab course, an analysis of user experiences, and our development actions to improve ELN training are presented here. ELN improved pedagogy and learning outcomes of the lab course through stream lined workflow, quick data recording and archiving, and enhanced data sharing and collaboration. It also enabled superior data integrity, simplified information exchange, and allowed real-time and remote monitoring of experiments. Several attributes related to positive user experiences of ELN improved between the two subsequent years in which ELN was offered. Student responses also indicate that ELN is better than PLN for compliance. We demonstrated that ELN can be successfully implemented in a lab course with significant benefits to pedagogy, GDP training, and data integrity. The methods and processes presented here for ELN implementation can be adapted to many types of laboratory experiments.

Vertical and Horizontal Integration of Laboratory Curricula and Course Projects across the Electronic Engineering Technology Program

Science.gov (United States)

Zhan, Wei; Goulart, Ana; Morgan, Joseph A.; Porter, Jay R.

2011-01-01

This paper discusses the details of the curricular development effort with a focus on the vertical and horizontal integration of laboratory curricula and course projects within the Electronic Engineering Technology (EET) program at Texas A&M University. Both software and hardware aspects are addressed. A common set of software tools are…

Admissions and Plebe Year Data as Indicators of Academic Success in Engineering Majors at the United States Naval Academy

National Research Council Canada - National Science Library

Kristof, Nicholas

2002-01-01

This research analyzes the relationship between academic success in high school and at the freshman collegiate level and academic performance in engineering majors at the United States Naval Academy (USNA...

Newnes electronics assembly pocket book

CERN Document Server

Brindley, Keith

2013-01-01

Produced in association with the Engineering Training Authority with contributions from dozens of people in the electronics industry. The material covers common skills in electrical and electronic engineering and concentrates mainly on wiring and assembly. 'Newnes Electronics Assembly Pocket Book' is for electronics technicians, students and apprentices.

Surfing for suicide methods and help: content analysis of websites retrieved with search engines in Austria and the United States.

Science.gov (United States)

Till, Benedikt; Niederkrotenthaler, Thomas

2014-08-01

The Internet provides a variety of resources for individuals searching for suicide-related information. Structured content-analytic approaches to assess intercultural differences in web contents retrieved with method-related and help-related searches are scarce. We used the 2 most popular search engines (Google and Yahoo/Bing) to retrieve US-American and Austrian search results for the term suicide, method-related search terms (e.g., suicide methods, how to kill yourself, painless suicide, how to hang yourself), and help-related terms (e.g., suicidal thoughts, suicide help) on February 11, 2013. In total, 396 websites retrieved with US search engines and 335 websites from Austrian searches were analyzed with content analysis on the basis of current media guidelines for suicide reporting. We assessed the quality of websites and compared findings across search terms and between the United States and Austria. In both countries, protective outweighed harmful website characteristics by approximately 2:1. Websites retrieved with method-related search terms (e.g., how to hang yourself) contained more harmful (United States: P search engines generally had more protective characteristics (P search engines. Resources with harmful characteristics were better ranked than those with protective characteristics (United States: P < .01, Austria: P < .05). The quality of suicide-related websites obtained depends on the search terms used. Preventive efforts to improve the ranking of preventive web content, particularly regarding method-related search terms, seem necessary. © Copyright 2014 Physicians Postgraduate Press, Inc.

Itegrated Test and Evaluation of a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removtal System (CDRA), Mechanical Compressor Engineering Development Unit (EDU), and Sabitier Engineering Development Unit (EDU)

Science.gov (United States)

Knox, James C.; Campbell, Melissa; Murdoch, Karen; Miller, Lee A.; Jeng, Frank

2005-01-01

Currently on the International Space Station s (ISS) U.S. Segment, carbon dioxide (CO2) scrubbed from the cabin by a 4-Bed Molecular Sieve (4BMS) Carbon Dioxide Removal Assembly (CDRA) is vented overboard as a waste product. Likewise, the product hydrogen (H2) that will be generated by the Oxygen Generation Assembly (OGA) planned for installation will also be vented. A flight experiment has been proposed that will take the waste CO2 removed from the cabin, and via the catalytic Sabatier process, reduce it with waste H2 to generate water and methane. The water produced may provide cost and logistics savings for ISS by reducing the amount of water periodically re-supplied to orbit. To make this concept viable, a mechanical piston compressor and accumulator were developed for collecting and storing the CO2 from the CDRA. The compressor, accumulator and Sabatier system would be packaged together as one unit and referred to as the Carbon Dioxide Reduction Assembly (CRA). Testing was required to evaluate the performance of a 4BMS CDRA, compressor, accumulator, and Sabatier performance along with their operating rules when integrated together. This had been numerically modeled and simulated; however, testing was necessary to verify the results from the engineering analyses. Testing also allowed a better understanding of the practical inefficiencies and control issues involved in a fully integrated system versus the theoretical ideals in the model. This paper presents and discusses the results of an integrated engineering development unit test.

Idaho National Engineering Laboratory irradiation facilities and their applications

International Nuclear Information System (INIS)

Gupta, V.P.; Herring, J.S.; Korenke, R.E.; Harker, Y.D.

1986-05-01

Although there is a growing need for neutron and gamma irradiation by governmental and industrial organizations in the United States and in other countries, the number of facilities providing such irradiations are limited. At the Idaho National Engineering Laboratory, there are several unique irradiation facilities producing high neutron and gamma radiation environments. These facilities could be readily used for nuclear research, materials testing, radiation hardening studies on electronic components/circuitry and sensors, and production of neutron transmutation doped (NTD) silicon and special radioisotopes. In addition, a neutron radiography unit, suitable for examining irradiated materials and assemblies, is also available. This report provides a description of the irradiation facilities and the neutron radiography unit as well as examples of their unique applications

A broadcast engineering tutorial for non-engineers

CERN Document Server

Pizzi, Skip

2014-01-01

A Broadcast Engineering Tutorial for Non-Engineers is the leading publication on the basics of broadcast technology. Whether you are new to the industry or do not have an engineering background, this book will give you a comprehensive primer of television, radio, and digital media relating to broadcast-it is your guide to understanding the technical world of radio and television broadcast engineering. It covers all the important topics such as DTV, IBOC, HD, standards, video servers, editing, electronic newsrooms, and more.

Engineering design of the interaction waveguide for high-power accelerator-driven microwave free-electron lasers

International Nuclear Information System (INIS)

Hopkins, D.B.; Clay, H.W.; Stallard, B.W.; Throop, A.L.; Listvinsky, G.; Makowski, M.A.

1989-01-01

Linear induction accelerators (LIAs) operating at beam energies of a few million electron volts and currents of a few thousand amperes are suitable drivers for free-electron lasers (FELs). Such lasers are capable of producing gigawatts of peak power and megawatts of average power at microwave frequencies. Such devices are being studied as possible power sources for future high-gradient accelerators and are being constructed for plasma heating applications. At high power levels, the engineering design of the interaction waveguide presents a challenge. This paper discusses several concerns, including electrical breakdown and metal fatigue limits, choice of material, and choice of operating propagation mode. 13 refs., 3 figs

Engineering report on the Grayburg Cooperative and unit area, Eddy County, New Mexico

Science.gov (United States)

Barnett, John A.; Soyster, Merwin H.

1945-01-01

This report covers the area committed to the Grayburg Cooperative and Unit Agreement (I-Sec. 370) approved by the Assistant Secretary of the Interior on October 5, 1943, hereafter referred to as the "unit area", embracing 4,769.44 acres of public land in T. 17 S., Rs. 29 and 30 E., Eddy County, New Mexico. The area includes portions of the Anderson, Grayburg-Jackson, and Leonard oil fields as defined for proration purposes by the New Mexico Oil Conservation Commission. The unit area is covered by Federal oil and gas leases owned by the Grayburg Oil Company of New Mexico and the Western Production Company, Inc. The Grayburg Unit Association has been formed and designated to conduct and manage all operations in the unit area. As of December 31, 1943, there were forty-six producing oil wells within the unit area. The report has been prepared for the purpose of assisting the Grayburg Unit Association in determining the proper locations of gas-injection wells and the best methods for future operation of the pressure-maintenance system that is being installed for the purpose of retarding the reservoir pressure decline and increasing the ultimate recovery of oil from the Grayburg Zone defined in the above-mentioned agreement as formations not more than 3300 feet below the surface. Data used in the report were obtained from records on file in the Geological Survey office at Roswell, New Mexico, and from the records of the Western Production Company and the Grayburg Oil Company. All data were carefully checked as to accuracy with engineers and field representatives of both companies.

Hydrogen Gas as a Fuel in Direct Injection Diesel Engine

Science.gov (United States)

Dhanasekaran, Chinnathambi; Mohankumar, Gabriael

2016-04-01

Hydrogen is expected to be one of the most important fuels in the near future for solving the problem caused by the greenhouse gases, for protecting environment and saving conventional fuels. In this study, a dual fuel engine of hydrogen and diesel was investigated. Hydrogen was conceded through the intake port, and simultaneously air and diesel was pervaded into the cylinder. Using electronic gas injector and electronic control unit, the injection timing and duration varied. In this investigation, a single cylinder, KIRLOSKAR AV1, DI Diesel engine was used. Hydrogen injection timing was fixed at TDC and injection duration was timed for 30°, 60°, and 90° crank angles. The injection timing of diesel was fixed at 23° BTDC. When hydrogen is mixed with inlet air, emanation of HC, CO and CO2 decreased without any emission (exhaustion) of smoke while increasing the brake thermal efficiency.

Organic High Electron Mobility Transistors Realized by 2D Electron Gas.

Science.gov (United States)

Zhang, Panlong; Wang, Haibo; Yan, Donghang

2017-09-01

A key breakthrough in inorganic modern electronics is the energy-band engineering that plays important role to improve device performance or develop novel functional devices. A typical application is high electron mobility transistors (HEMTs), which utilizes 2D electron gas (2DEG) as transport channel and exhibits very high electron mobility over traditional field-effect transistors (FETs). Recently, organic electronics have made very rapid progress and the band transport model is demonstrated to be more suitable for explaining carrier behavior in high-mobility crystalline organic materials. Therefore, there emerges a chance for applying energy-band engineering in organic semiconductors to tailor their optoelectronic properties. Here, the idea of energy-band engineering is introduced and a novel device configuration is constructed, i.e., using quantum well structures as active layers in organic FETs, to realize organic 2DEG. Under the control of gate voltage, electron carriers are accumulated and confined at quantized energy levels, and show efficient 2D transport. The electron mobility is up to 10 cm 2 V -1 s -1 , and the operation mechanisms of organic HEMTs are also argued. Our results demonstrate the validity of tailoring optoelectronic properties of organic semiconductors by energy-band engineering, offering a promising way for the step forward of organic electronics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XI, PART I--MAINTAINING THE FUEL SYSTEM (PART I), CUMMINS DIESEL ENGINES, PART II--UNIT REPLACEMENT (ENGINE).

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF DIFFERENCES BETWEEN TWO AND FOUR CYCLE ENGINES, THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM, AND THE PROCEDURES FOR DIESEL ENGINE REMOVAL. TOPICS ARE (1) REVIEW OF TWO CYCLE AND FOUR CYCLE CONCEPT, (2) SOME BASIC CHARACTERISTICS OF FOUR CYCLE ENGINES,…

Modified Current Differencing Unit and its Application for Electronically Reconfigurable Simple First-order Transfer Function

Directory of Open Access Journals (Sweden)

SOTNER, R.

2015-02-01

Full Text Available Modified current differencing unit (MCDU and its simple filtering application are introduced in this paper. Modification of the well-known current differencing unit consists in weighted difference of both input currents controlled by adjustable current gain, controllable intrinsic resistance of both current input terminals, and availability of additional voltage terminal(s. Definition of MCDU therefore requires four adjustable parameters (B1, B2, Rp, Rn. A presented active element offers and combines benefits of electronically controllable current conveyor of second generation and current differencing unit and allows synthesis of interesting adjustable applications, which are not available by classical approaches based on simple elements. MCDU brings variability of the transfer function into the structure. It provides several transfer types without necessity of input or output node change by simple electronic tuning. A presented structure represents so-called reconnection-less reconfigurable current-mode filter for realization of all-pass, inverting high-pass, low-pass and direct transfer response. Behavioral model of the MCDU was prepared and carefully tested in filtering application. Spice simulations and measurements confirmed theoretical assumptions.

Engineering evaluation/conceptual plan for the 200-UP-1 Groundwater Operable Unit interim remedial measure. Revision 2

International Nuclear Information System (INIS)

1996-03-01

This report presents an engineering evaluation and conceptual plan for an interim remedial measure (IRM) to address a uranium and technetium-99 groundwater plume in the 200-UP-1 Groundwater Operable Unit located in the 200 West Area of the Hanford Site. This report provides information regarding the need for an IRM and its potentially achievable objectives and goals. The report also evaluates alternatives to contain elevated concentrations of uranium and technetium-99 and to obtain information necessary to develop final remedial actions for the operable unit

Project based education as motivation factor in undergraduate program in Electronics at Copenhagen University College of Engineering

DEFF Research Database (Denmark)

Friesel, Anna

2012-01-01

This paper summarizes the contents of our experience with project based courses and team work in the undergraduate program in Electronics. The main points of our program are described in this paper, where the leading idea is to combine theory with practical engineering projects. Our students work...

Summary of the engineering assessment of inactive uranium mill tailings: Phillips/United Nuclear site, Ambrosia Lake, New Mexico

International Nuclear Information System (INIS)

1981-10-01

Ford, Bacon and Davis Utah, Inc., has reevaluated the Phillips/United Nuclear site in order to revise the December 1977 engineering assessment of the problems resulting from the existence of radioactive uranium mill tailings at Ambrosia Lake, New Mexico. This engineering assessment has included the preparation of topographic maps, the performance of core drillings and radiometric maps, the performance of core drillings and radiometric measurements sufficient to determine areas and volumes of tailings and radiation exposures of individuals and nearby populations, the investigations of site hydrology and meteorology, and the evaluation and costing of alternative corrective actions. Radon gas released from the 2.6 million dry tons of tailings at the Phillips/United Nuclear site constitutes the most significant environmental impact, although windblown tailings and external gamma radiation also are factors. The four alternative actions presented in this engineering assessment range from millsite decontamination with the addition of 3 m of stabilization cover material, to removal of the tailings to remote disposal sites and decontamination of the tailings site. Cost estimates for the four options range from about $21,500,000 for stabilization in-place, to about $45,200,000 for disposal at a distance of about 15 mi. Three principal alternatives for the reprocessing of the Phillips/United Nuclear tailings were examined: heap leaching; treatment at an existing mill; reprocessing at a new conventional mill constructed for tailings reprocessing. The cost of the uranium recovered would be about $87/lb of U 3 O 8 by either heap leach or conventional plant process. The spot market price for uranium was $25/lb early in 1981. Reprocessing the Phillips/United Nuclear tailings for uranium recovery does not appear to be economically attractive under present or foreseeable market conditions

Engine Tune-Up Service. Unit 5: Fuel and Carburetion Systems. Review Exercise Book. Automotive Mechanics Curriculum.

Science.gov (United States)

Goodson, Ludy

This book of pretests and review exercises is designed to accompany the Engine Tune-Up Service Student Guide for Unit 5, Fuel and Carburetion Systems, available separately as CE 031 217. Focus of the exercises and pretests is inspecting and servicing the fuel and carburetion systems. Pretests and performance checklists are provided for each of the…

A practical approach for electron monitor unit calculation

International Nuclear Information System (INIS)

Choi, David; Patyal, Baldev; Cho, Jongmin; Cheng, Ing Y; Nookala, Prashanth

2009-01-01

Electron monitor unit (MU) calculation requires measured beam data such as the relative output factor (ROF) of a cone, insert correction factor (ICF) and effective source-to-surface distance (ESD). Measuring the beam data to cover all possible clinical cases is not practical for a busy clinic because it takes tremendous time and labor. In this study, we propose a practical approach to reduce the number of data measurements without affecting accuracy. It is based on two findings of dosimetric properties of electron beams. One is that the output ratio of two inserts is independent of the cone used, and the other is that ESD is a function of field size but independent of cone and jaw opening. For the measurements to prove the findings, a parallel plate ion chamber (Markus, PTW 23343) with an electrometer (Cardinal Health 35040) was used. We measured the outputs to determine ROF, ICF and ESD of different energies (5-21 MeV). Measurements were made in a Plastic Water(TM) phantom or in water. Three linear accelerators were used: Siemens MD2 (S/N 2689), Siemens Primus (S/N 3305) and Varian Clinic 21-EX (S/N 1495). With these findings, the number of data set to be measured can be reduced to less than 20% of the data points. (note)

UPTF test instrumentation. Measurement system identification, engineering units and computed parameters

International Nuclear Information System (INIS)

Sarkar, J.; Liebert, J.; Laeufer, R.

1992-11-01

This updated version of the previous report /1/ contains, besides additional instrumentation needed for 2D/3D Programme, the supplementary instrumentation in the inlet plenum of SG simulator and hot and cold leg of broken loop, the cold leg of intact loops and the upper plenum to meet the requirements (Test Phase A) of the UPTF Programme, TRAM, sponsored by the Federal Minister of Research and Technology (BMFT) of the Federal Republic of Germany. For understanding, the derivation and the description of the identification codes for the entire conventional and advanced measurement systems classifying the function, and the equipment unit, key, as adopted in the conventional power plants, have been included. Amendments have also been made to the appendices. In particular, the list of measurement systems covering the measurement identification code, instrument, measured quantity, measuring range, band width, uncertainty and sensor location has been updated and extended to include the supplementary instrumentation. Beyond these amendments, the uncertainties of measurements have been precisely specified. The measurement identification codes which also stand for the identification of the corresponding measured quantities in engineering units and the identification codes derived therefrom for the computed parameters have been adequately detailed. (orig.)

The Status of Technology and Engineering Education in the United States: A Fourth Report of the Findings from the States (2011-12)

Science.gov (United States)

Moye, Johnny J.; Dugger, William E., Jr.; Starkweather, Kendall N.

2012-01-01

Technology and engineering education continues to evolve as it becomes more apparent that students need this information to become more successful in college and careers. The International Technology and Engineering Educators Association (ITEEA ) has tracked the status of technology education in the United States in three separate studies over the…

Electrical engineer's reference book

CERN Document Server

Laughton, M A

1985-01-01

Electrical Engineer's Reference Book, Fourteenth Edition focuses on electrical engineering. The book first discusses units, mathematics, and physical quantities, including the international unit system, physical properties, and electricity. The text also looks at network and control systems analysis. The book examines materials used in electrical engineering. Topics include conducting materials, superconductors, silicon, insulating materials, electrical steels, and soft irons and relay steels. The text underscores electrical metrology and instrumentation, steam-generating plants, turbines

Future trends in agricultural engineering.

NARCIS (Netherlands)

Jongebreur, A.A.; Speelman, L.

1997-01-01

Beside traditional mechanical engineering, other engineering branches such as electronics, control engineering and physics play their specific role within the agricultural engineering field. Agricultural engineering has affected and stimulated major changes in agriculture. In the last decades

Electrical engineering yearbook 1994. 13. ed. Jahrbuch Elektrotechnik '94; Daten, Fakten, Trends

Energy Technology Data Exchange (ETDEWEB)

Gruetz, A. (ed.)

1993-01-01

The book gives a current view of the wide field of electrical engineering and electronics. Contents: Fuzzing logic; neural networks; data systems; electromagnetic radiation; electric motors of advanced technology; DIN VDE 0100; construction regulations for power transmission systems. The appendix contains the VDE guide, statistical data of the German electric power industry and electricity supply industry, technical units, and a calendar. (orig.)

Crash problem definition and safety benefits methodology for stability control for single-unit medium and heavy trucks and large-platform buses

Science.gov (United States)

2009-10-01

This report presents the findings of a comprehensive engineering analysis of electronic stability control (ESC) and roll stability control (RSC) systems for single-unit medium and heavy trucks and large-platform buses. This report details the applica...

First-year Engineering Education with the Creative Electrical Engineering Laboratory

Science.gov (United States)

Tsukamoto, Takehiko; Sugito, Tetsumasa; Ozeki, Osamu; Ushiroda, Sumio

The Department of Electrical and Electronic Engineering in Toyota National College of Technology has put great emphasis on fundamental subjects. We introduced the creative electrical engineering laboratory into the first-year engineering education since 1998. The laboratory concentrates on the practice exercise. The final questionnaire of students showed that our first-year education is very effective to promote students motivation and their scholastic ability in engineering.

Design of a Facility to Test the Advanced Stirling Radioisotope Generator Engineering Unit

Science.gov (United States)

Lewandowski, Edward J.; Schreiber, Jeffrey G.; Oriti, Salvatore M.; Meer, David W.; Brace, Michael H.; Dugala, Gina

2009-01-01

The Advanced Stirling Radioisotope Generator (ASRG) is being considered to power deep space missions. An engineering unit, the ASRG-EU, was designed and fabricated by Lockheed Martin under contract to the Department of Energy. This unit is currently on an extended operation test at NASA Glenn Research Center to generate performance data and validate the life and reliability predictions for the generator and the Stirling convertors. A special test facility was designed and built for testing the ASRG-EU. Details of the test facility design are discussed. The facility can operate the convertors under AC bus control or with the ASRG-EU controller. It can regulate input thermal power in either a fixed temperature or fixed power mode. An enclosure circulates cooled air around the ASRG-EU to remove heat rejected from the ASRG-EU by convection. A custom monitoring and data acquisition system supports the test. Various safety features, which allow 2417 unattended operation, are discussed.

Flat-panel electronic displays: a triumph of physics, chemistry and engineering.

Science.gov (United States)

Hilsum, Cyril

2010-03-13

This paper describes the history and science behind the development of modern flat-panel displays, and assesses future trends. Electronic displays are an important feature of modern life. For many years the cathode ray tube, an engineering marvel, was universal, but its shape was cumbersome and its operating voltage too high. The need for a flat-panel display, working at a low voltage, became imperative, and much research has been applied to this need. Any versatile flat-panel display will exploit an electro-optical effect, a transparent conductor and an addressing system to deliver data locally. The first need is to convert an electrical signal into a visible change. Two methods are available, the first giving emission of light, the second modulating ambient illumination. The most useful light-emitting media are semiconductors, historically exploiting III-V or II-VI compounds, but more recently organic or polymer semiconductors. Another possible effect uses gas plasma discharges. The modulating, or subtractive, effects that have been studied include liquid crystals, electrophoresis, electrowetting and electrochromism. A transparent conductor makes it possible to apply a voltage to an extended area while observing the results. The design is a compromise, since the free electrons that carry current also absorb light. The first materials used were metals, but some semiconductors, when heavily doped, give a better balance, with high transmission for a low resistance. Delivering data unambiguously to a million or so picture elements across the display area is no easy task. The preferred solution is an amorphous silicon thin-film transistor deposited at each cross-point in an X-Y matrix. Success in these endeavours has led to many applications for flat-panel displays, including television, flexible displays, electronic paper, electronic books and advertising signs.

AUTOMOTIVE DIESEL MAINTENANCE L. UNIT XII, PART I--MAINTAINING THE FUEL SYSTEM (PART II), CUMMINS DIESEL ENGINE, PART II--UNIT INSTALLATION (ENGINE).

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM AND THE PROCEDURES FOR DIESEL ENGINE INSTALLATION. TOPICS ARE FUEL FLOW CHARACTERISTICS, PTG FUEL PUMP, PREPARATION FOR INSTALLATION, AND INSTALLING ENGINE. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH…

Common Rail System for GDI Engines Modelling, Identification, and Control

CERN Document Server

Fiengo, Giovanni; Palladino, Angelo; Giglio, Veniero

2013-01-01

Progressive reductions in vehicle emission requirements have forced the automotive industry to invest in research and development of alternative control strategies. Continual control action exerted by a dedicated electronic control unit ensures that best performance in terms of pollutant emissions and power density is married with driveability and diagnostics. Gasoline direct injection (GDI) engine technology is a way to attain these goals. This brief describes the functioning of a GDI engine equipped with a common rail (CR) system, and the devices necessary to run test-bench experiments in detail. The text should prove instructive to researchers in engine control and students are recommended to this brief as their first approach to this technology. Later chapters of the brief relate an innovative strategy designed to assist with the engine management system; injection pressure regulation for fuel pressure stabilization in the CR fuel line is proposed and validated by experiment. The resulting control scheme ...

Study of technical and economical feasibility for implementation of a movable unit for treatment of industrial effluents with electron beam

International Nuclear Information System (INIS)

Rela, Carolina Sciamarelli

2006-01-01

The treatment of industrial effluents is a practice that is disseminating in accelerated rhythm, of contributing to reinforce the public image, through the combat of the pollution, it brings economical advantages allowing the companies the reuse of the treated water in their own processes. The liquid effluent treatment technique studied in the present work is the one that uses the chemical oxidation/reduction standing out the use of the electron beam (e.b.) radiation. This technique uses an advanced oxidation process, generating radicals highly reagents that provoke the oxidation, reduction, dissociation and degradation in composed organic and exercising lethal effect in general in the microorganisms and parasites. In this work a conceptual and basic project of a movable unit of effluents treatment using electron beam radiation process was developed, in order that the unit moves until the treatment point, where the effluent is produced, facilitating the logistics. A technical and economical feasibility study was also elaborated allowing data on the capacity and cost of effluents processing to consolidate the values of the necessary investments to be presented to foundations organs for the construction of a movable unit. The results of the studies demonstrated that it is technically viable attending the pertinent legislation of Brazil, in the aspects of Radiation Protection and transport limit capacity. The unitary cost of the e.b. radiation processing in the movable unit was shown more expensive than in the fixed unit, the reason is the decrease of the efficiency of the interaction of the incident electrons in the effluent, due to the reduction of electron energy operation time of the unit. (author)

Technician Career Opportunities in Engineering Technology.

Science.gov (United States)

Engineers' Council for Professional Development, New York, NY.

Career opportunities for engineering technicians are available in the technologies relating to air conditioning, heating, and refrigeration, aviation and aerospace, building construction, chemical engineering, civil engineering, electrical engineering, electronics, industrial engineering, instrumentation, internal combustion engines, mechanical…

Testing of the Advanced Stirling Radioisotope Generator Engineering Unit at NASA Glenn Research Center

Science.gov (United States)

Lewandowski, Edward J.

2013-01-01

The Advanced Stirling Radioisotope Generator (ASRG) is a high-efficiency generator being developed for potential use on a Discovery 12 space mission. Lockheed Martin designed and fabricated the ASRG Engineering Unit (EU) under contract to the Department of Energy. This unit was delivered to NASA Glenn Research Center in 2008 and has been undergoing extended operation testing to generate long-term performance data for an integrated system. It has also been used for tests to characterize generator operation while varying control parameters and system inputs, both when controlled with an alternating current (AC) bus and with a digital controller. The ASRG EU currently has over 27,000 hours of operation. This paper summarizes all of the tests that have been conducted on the ASRG EU over the past 3 years and provides an overview of the test results and what was learned.

Integrating electron microscopy into nanoscience and materials engineering programs

Science.gov (United States)

Cormia, Robert D.; Oye, Michael M.; Nguyen, Anh; Skiver, David; Shi, Meng; Torres, Yessica

2014-10-01

Preparing an effective workforce in high technology is the goal of both academic and industry training, and has been the engine that drives innovation and product development in the United States for over a century. During the last 50 years, technician training has comprised a combination of two-year academic programs, internships and apprentice training, and extensive On-the-Job Training (OJT). Recently, and especially in Silicon Valley, technicians have four-year college degrees, as well as relevant hands-on training. Characterization in general, and microscopy in particular, is an essential tool in process development, manufacturing and QA/QC, and failure analysis. Training for a broad range of skills and practice is challenging, especially for community colleges. Workforce studies (SRI/Boeing) suggest that even four year colleges often do not provide the relevant training and experience in laboratory skills, especially design of experiments and analysis of data. Companies in high-tech further report difficulty in finding skilled labor, especially with industry specific experience. Foothill College, in partnership with UCSC, SJSU, and NASA-Ames, has developed a microscopy training program embedded in a research laboratory, itself a partnership between university and government, providing hands-on experience in advanced instrumentation, experimental design and problem solving, with real-world context from small business innovators, in an environment called `the collaboratory'. The program builds on AFM-SEM training at Foothill, and provides affordable training in FE-SEM and TEM through a cost recovery model. In addition to instrument and engineering training, the collaboratory also supports academic and personal growth through a multiplayer social network of students, faculty, researchers, and innovators.

Electronic communication preferences among mothers in the neonatal intensive care unit.

Science.gov (United States)

Weems, M F; Graetz, I; Lan, R; DeBaer, L R; Beeman, G

2016-11-01

Mobile communication with the medical-care team has the potential to decrease stress among parents of infants admitted to the neonatal intensive care unit (NICU). We assessed mobile use and communication preferences in a population of urban minority NICU mothers. A 30-question English language survey was administered to mothers of NICU patients. The survey was completed by 217 mothers, 75% were Black, and 75% reported annual household income below $20 000. Only 56% had a computer with Internet access at home, but 79% used smartphones. Most (79%) have searched the Internet for health information in the past year. Receiving electronic messages about their babies was viewed favorably, and text messaging was the preferred platform. The majority of mothers felt electronic messaging would improve communication but should not replace verbal communication. Mobile communication is used widely in this population of NICU mothers and could potentially improve provider-parent communication and reduce parental stress.

The European Engineer: A British Civil Engineering Viewpoint.

Science.gov (United States)

Fleming, George

1988-01-01

Confronts the problems of defining the European Engineer in terms of educational and practical training. Analyzes the supply and demand requirements of engineering management and practice. Compares these analyses with conditions in the United States. Gives details of the educational process in a number of European countries. (CW)

Impact of an Engineering Case Study in a High School Pre-Engineering Course

Science.gov (United States)

Rutz, Eugene; Shafer, Michelle

2011-01-01

Students at an all-girls high school who were enrolled in an introduction to engineering course were presented an engineering case study to determine if the case study affected their attitudes toward engineering and their abilities to solve engineering problems. A case study on power plants was implemented during a unit on electrical engineering.…

Gradient ascent pulse engineering approach to CNOT gates in donor electron spin quantum computing

International Nuclear Information System (INIS)

Tsai, D.-B.; Goan, H.-S.

2008-01-01

In this paper, we demonstrate how gradient ascent pulse engineering (GRAPE) optimal control methods can be implemented on donor electron spin qubits in semiconductors with an architecture complementary to the original Kane's proposal. We focus on the high fidelity controlled-NOT (CNOT) gate and we explicitly find the digitized control sequences for a controlled-NOT gate by optimizing its fidelity using the effective, reduced donor electron spin Hamiltonian with external controls over the hyperfine A and exchange J interactions. We then simulate the CNOT-gate sequence with the full spin Hamiltonian and find that it has an error of 10 -6 that is below the error threshold of 10 -4 required for fault-tolerant quantum computation. Also the CNOT gate operation time of 100 ns is 3 times faster than 297 ns of the proposed global control scheme.

Electronic structure engineering in silicene via atom substitution and a new two-dimensional Dirac structure Si3C

Science.gov (United States)

Yin, Na; Dai, Ying; Wei, Wei; Huang, Baibiao

2018-04-01

A lot of efforts have been made towards the band gap opening in two-dimensional silicene, the silicon version of graphene. In the present work, the electronic structures of single atom doped (B, N, Al and P) and codoped (B/N and Al/P) silicene monolayers are systematically examined on the base of density functional electronic calculations. Our results demonstrate that single atom doping can realize electron or hole doping in the silicene; while codoping, due to the syergistic effects, results in finite band gap in silicene at the Dirac point without significantly degrading the electronic properties. In addition, the characteristic of band gap shows dependence on the doping concentration. Importantly, we predict a new two-dimensional Dirac structure, the graphene-like Si3C, which also shows linear band dispersion relation around the Fermi level. Our results demonstrates an important perspective to engineer the electronic and optical properties of silicene.

CREATING AND AUDITING A NEW ELECTRONIC CONTINUOUS INFUSION PRESCRIPTION CHART FOR A PAEDIATRIC CRITICAL CARE UNIT.

Science.gov (United States)

Siu, Emily; Sadasivam, Kalaimaran; Christiansen, Nanna

2016-09-01

Prescription errors, including continuous infusion prescriptions are one major source of concern in the paediatric population. Evidence suggests that use of an electronic or web-based calculator could minimise these errors. In our paediatric critical care unit (PCCU) we have created an electronic continuous infusion prescription chart to target errors in this area and conducted an audit to assess its effect on error reduction. To create an electronic continuous infusion prescription chart and audit its effect on prescription errors. Similar electronic continuous infusion prescription charts were evaluated. A Choice of electronic formats were considered and excel was chosen for its simplicity and flexibility. The choice of medications to be included, dilution method, and dosage range was agreed between PCCU consultant, pharmacy and nursing staff. Formulas for calculating each medication infusion was created and validated for different age and weight ranges by at least 2 PCCU trained pharmacists, accounting for capping at certain age and weight bands as appropriate for the medication. These were programmed into the spreadsheet for automatic calculation using inputted age and weight for the selected medications. Continuous infusion prescriptions were audited 6 months before and after implementation in April 2015 of this electronic chart. Parameters audited include medication dose, infusion rate, concentration, route, legibility, and missing or incorrect patient details. A trial period of 4 weeks preceded implementation. The electronic continuous infusion prescription form was created and used on PCCU. Hand written prescriptions had higher error rate (30.7%) as compared to electronic charts (0.7%) with a p-value <0.002. No errors were found in electronic prescriptions in regards to dose, volume and rate calculation. The use of an electronic continuous infusion prescription chart has been successfully set up and used on PCCU. Its use has significantly reduced continuous

75 FR 2463 - Continuing Contract for Civil Works Project Managed by the United States Army Corps of Engineers...

Science.gov (United States)

2010-01-15

... be considered a breach of contract and shall not entitle the Contractor to a price adjustment under... constitute a breach of this contract and shall not entitle the Contractor to any price adjustment under the... Continuing Contract for Civil Works Project Managed by the United States Army Corps of Engineers Clauses...

An Optimized Thermal Analysis of Electronic Unit Used in Aircraft

International Nuclear Information System (INIS)

Shah, A.N.; Mir, F.; Farooq, M.; Farooq, M.

2014-01-01

In a field where change and growth is inevitable, new electronic packaging problems continuously arise. Smaller, but more powerful devices are prone to overheating causing intermittent system failures, corrupted signals and outright system failure. Current study is focused on the analysis of the optimized working of electronic equipment from thermal point of view. In order to achieve the objective, an approach was developed for the thermal analysis of Printed Circuit Board (PCB) including the heat dissipation of its electronic components and then removal of the heat in a sophisticated manner by considering the conduction and convection modes of heat transfer. Mathematical modeling was carried out for a certain problem to address the thermal design, and then a program was developed in MATLAB for the solution of model by using Newton-Raphson method. The proposed unit is to be mounted on an aircraft having suspected thermal characteristics owing to abrupt changes in pressure and temperature as aircraft moves quickly from a lower altitude to higher altitude. In current study, dominant mode of heat transfer was conduction revealing that the major portion of heat transfer takes place by copper cladding and that heat conduction along the length of PCB can be improved enormously by using even thin layer of copper. The results confirmed that temperatures of all the electronic components were within derated values. Meanwhile, it was known that convection also plays a significant role in the reduction of temperatures of the components. The reduction in nodal temperature was in the range of 13 to 42 %. Furthermore, altitude variation from sea level to 15240 m (above sea level) caused the reduction in pressure from 1atm to 0.1095 atm. Consequently, the temperature of the electronic components increased from 73.25 degree C to 83.83 degree C for first node 'a', and from 66.04 degree C to 68.47 degree C for last node 'n' because of the decrease in the convective heat transfer

Reconstruction of Orion Engineering Development Unit (EDU) Parachute Inflation Loads

Science.gov (United States)

Ray, Eric S.

2013-01-01

The process of reconstructing inflation loads of Capsule Parachute Assembly System (CPAS) has been updated as the program transitioned to testing Engineering Development Unit (EDU) hardware. The equations used to reduce the test data have been re-derived based on the same physical assumptions made by simulations. Due to instrumentation challenges, individual parachute loads are determined from complementary accelerometer and load cell measurements. Cluster inflations are now simulated by modeling each parachute individually to better represent different inflation times and non-synchronous disreefing. The reconstruction procedure is tailored to either infinite mass or finite mass events based on measurable characteristics from the test data. Inflation parameters are determined from an automated optimization routine to reduce subjectivity. Infinite mass inflation parameters have been re-defined to avoid unrealistic interactions in Monte Carlo simulations. Sample cases demonstrate how best-fit inflation parameters are used to generate simulated drag areas and loads which favorably agree with test data.

78 FR 18234 - Service of Process on Manufacturers; Manufacturers Importing Electronic Products Into the United...

Science.gov (United States)

2013-03-26

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration 21 CFR Part 1005 [Docket No. FDA-2007-N-0091; (formerly 2007N-0104)] Service of Process on Manufacturers; Manufacturers Importing Electronic Products Into the United States; Agent Designation; Change of Address AGENCY: Food and Drug...

Computer programs for unit-cell determination in electron diffraction experiments

International Nuclear Information System (INIS)

Li, X.Z.

2005-01-01

A set of computer programs for unit-cell determination from an electron diffraction tilt series and pattern indexing has been developed on the basis of several well-established algorithms. In this approach, a reduced direct primitive cell is first determined from experimental data, in the means time, the measurement errors of the tilt angles are checked and minimized. The derived primitive cell is then checked for possible higher lattice symmetry and transformed into a proper conventional cell. Finally a least-squares refinement procedure is adopted to generate optimum lattice parameters on the basis of the lengths of basic reflections in each diffraction pattern and the indices of these reflections. Examples are given to show the usage of the programs

MODELING OF THE FUNCTIONING UNITS OF FUEL SYSTEM OF GAS TURBINE ENGINE AIRCRAFT IN VIEW OF AVIATION FUEL QUALITY CHANGES

OpenAIRE

I. I. Zavyalik; V. S. Oleshko; V. M. Samoylenko; E. V. Fetisov

2016-01-01

The article describes the developed modeling system in MATLAB Simulink which allows to simulate, explore and pre- dict the technical condition of the units of the aircraft gas turbine engine fuel system depending on aviation fuel quality changes.

Investigation of thermal management materials for automotive electronic control units

International Nuclear Information System (INIS)

Mallik, Sabuj; Ekere, Ndy; Best, Chris; Bhatti, Raj

2011-01-01

Today's electronics packages are smaller and more powerful than ever before. This leads to ever increasing thermal challenges for the systems designer. The automotive electronic control unit (ECU) package faces the same challenge of thermal management as the industry in general. This is coupled with the latest European Union legislation (Euro 6 standard) which forced the ECU manufacturers to completely re-design their ECU platform with improved hardware and software capability. This will result in increased power densities and therefore, the ability to dissipate heat will be a key factor. A higher thermal conductivity (TC) material for the ECU housing (than the currently used Aluminium) could improve heat dissipation from the ECU. This paper critically reviews the state-of-the-art in thermal management materials which may be applicable to an automotive ECU. This review shows that of the different materials currently available, the Al/SiC composites in particular have very good potential for automotive ECU application. In terms of metal composites processing, the liquid metal infiltration process is recommended as it has a lower processing cost and it also has the ability to produce near net-shape materials.

Developing a New Industrial Engineering Curriculum Using a Systems Engineering Approach

Science.gov (United States)

Buyurgan, Nebil; Kiassat, Corey

2017-01-01

This paper reports on the development of an engineering curriculum for a new industrial engineering programme at a medium-sized private university in the northeast United States. A systems engineering process has been followed to design and develop the new curriculum. Considering the programme curriculum as a system, first the stakeholders have…

Sales of Nicotine-Containing Electronic Cigarette Products: United States, 2015.

Science.gov (United States)

Marynak, Kristy L; Gammon, Doris G; Rogers, Todd; Coats, Ellen M; Singh, Tushar; King, Brian A

2017-05-01

To assess the proportion of electronic cigarette (e-cigarette) products sold in the United States that contain nicotine according to retail scanner data. We obtained unit sales data from January 11, 2015, to December 12, 2015, from The Nielsen Company for convenience stores; supermarkets; mass merchandisers; drug, club, and dollar stores; and Department of Defense commissaries. The data did not include purchases from tobacco specialty shops, "vape shops," or online sources. Nicotine content was assessed by product type (disposables, rechargeables, and refills), region, and flavor status based on nicotine strength listed in the Universal Product Codes. For the 36.7% of entries lacking nicotine content information, we conducted Internet searches by brand, product, and flavor. In 2015, 99.0% of e-cigarette products sold contained nicotine, including 99.0% of disposables, 99.7% of rechargeables, and 98.8% of refills. Overall, 98.7% of flavored e-cigarette products and 99.4% of nonflavored e-cigarette products contained nicotine. In 2015, almost all e-cigarette products sold in US convenience stores and other assessed channels contained nicotine. Public Health Implications. Findings reinforce the importance of warning labels for nicotine-containing products, ingredient reporting, and restrictions on sales to minors.

Elevating Learner Achievement Using Formative Electronic Lab Assessments in the Engineering Laboratory: A Viable Alternative to Weekly Lab Reports

Science.gov (United States)

Chen, Baiyun; DeMara, Ronald F.; Salehi, Soheil; Hartshorne, Richard

2018-01-01

A laboratory pedagogy interweaving weekly student portfolios with onsite formative electronic laboratory assessments (ELAs) is developed and assessed within the laboratory component of a required core course of the electrical and computer engineering (ECE) undergraduate curriculum. The approach acts to promote student outcomes, and neutralize…

Nuclear engineering education in the United States

International Nuclear Information System (INIS)

Williamson, T.G.

1982-01-01

The critical issue facing the nuclear engineering education community today is first and foremost enrollment in a time of increasing demand for graduate engineers. Related to the issue of enrollment is support for graduate students, whether it be fellowships, traineeships, or research assistantships. Other issues are those of maintaining a vital faculty in the face of competitive job market, of maintaining research facilities and developing new ones, and last and certainly not least that of determining the directions of our educational efforts in the future. These issues are examined in the paper. (author)

MODELING OF THE FUNCTIONING UNITS OF FUEL SYSTEM OF GAS TURBINE ENGINE AIRCRAFT IN VIEW OF AVIATION FUEL QUALITY CHANGES

Directory of Open Access Journals (Sweden)

I. I. Zavyalik

2016-01-01

Full Text Available The article describes the developed modeling system in MATLAB Simulink which allows to simulate, explore and pre- dict the technical condition of the units of the aircraft gas turbine engine fuel system depending on aviation fuel quality changes.

Chaotic Motions in the Real Fuzzy Electronic Circuits (Preprint)

Science.gov (United States)

2012-12-01

phenomenon of chaos has attracted widespread attention amongst mathematicians , physicists , engineers and has also been extensively studied in many...CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING...100kΩ5kΩ 100kΩ 100kΩ Y X Y X Y X Fig.1 The fuzzy electronic circuit for chaotic Lorenz system. 14 Fig.2 Projection of phase portraits

Engineering physics

CERN Document Server

Mukherji, Uma

2015-01-01

ENGINEERING PHYSICS is designed as a textbook for first year engineering students of a two semester course in Applied Physics according to new revised syllabus. However the scope of this book is not only limited to undergraduate engineering students and science students, it can also serve as a reference book for practicing scientists.Advanced technological topics like LCD, Squid, Maglev system, Electron microscopes, MRI, Photonics - Photonic fibre, Nano-particles, CNT, Quantum computing etc., are explained with basic underlying principles of Physics.This text explained following topics with numerous solved, unsolved problems and questions from different angles. Part-I contains crystal structure, Liquid crystal, Thermo-electric effect, Thermionic emission, Ultrasonic, Acoustics, semiconductor and magnetic materials. Whereas Part-2 contains Optics, X-rays, Electron optics, Dielectric materials, Quantum Physics and Schrodinger wave equation, Laser, Fibre-optics and Holography, Radio-activity, Super-conductivity,...

Low-Cost Virtual Laboratory Workbench for Electronic Engineering

Science.gov (United States)

Achumba, Ifeyinwa E.; Azzi, Djamel; Stocker, James

2010-01-01

The laboratory component of undergraduate engineering education poses challenges in resource constrained engineering faculties. The cost, time, space and physical presence requirements of the traditional (real) laboratory approach are the contributory factors. These resource constraints may mitigate the acquisition of meaningful laboratory…

Teaching strategies applied to teaching computer networks in Engineering in Telecommunications and Electronics

Directory of Open Access Journals (Sweden)

Elio Manuel Castañeda-González

2016-07-01

Full Text Available Because of the large impact that today computer networks, their study in related fields such as Telecommunications Engineering and Electronics is presented to the student with great appeal. However, by digging in content, lacking a strong practical component, you can make this interest decreases considerably. This paper proposes the use of teaching strategies and analogies, media and interactive applications that enhance the teaching of discipline networks and encourage their study. It is part of an analysis of how the teaching of the discipline process is performed and then a description of each of these strategies is done with their respective contribution to student learning.

Practical framework for Bloom's based teaching and assessment of engineering outcomes

Science.gov (United States)

Mead, Patricia F.; Bennett, Mary M.

2009-06-01

ABET's outcomes-based assessment and evaluation requirements for engineering school accreditation has been a catalyst for curricular reform for engineering programs across the U.S. and around the world. Norfolk State University launched programs in Electronics and Optical Engineering in 2003. In 2007, Norfolk State became one of only six accredited Optical Engineering programs in the United States. In preparation for their first ABET evaluation in fall 2007, the faculty initiated an embedded-assessment program to insure continuous improvement toward the desired learning outcomes. The initial program design includes embedded assessments that have been generated using a practical framework for the creation of course activities based on Bloom's Learning Taxonomy. The framework includes specific performance criteria for each ABET-defined learning outcome. The embedded assessments are generated by individual faculty for courses that they are assigned to teach, and the performance criteria provide sufficient information to guide the faculty as they generate the embedded assignments. The assignments are typically administered through course exams, projects, electronic portfolio assignments, and other structured educational activities. The effectiveness of the assessment design is being evaluated through faculty surveys, faculty group discussions, and student performance. This paper outlines the assessment and evaluation plan, and the integrated processes that have been used to support the evaluation of learning outcomes using embedded assessment instruments.

Joining the Nuclear Renaissance with the Engineering Business Unit of AREVA

Energy Technology Data Exchange (ETDEWEB)

Hubert, Nathalie; Menguy, Stephane [SGN, AREVA Group, 1 rue des Herons, 78182 Saint-Quentin en Yvelines Cedex (France); Valery, Jean-Francois [AREVA NC, AREVA Group, Tour AREVA, 1 place de la Coupole, 92084 Paris La Defense Cedex (France)

2008-07-01

The reality of the nuclear renaissance is no longer a question. All over the world, new nuclear plants are going to be deployed; the whole fuel cycle has to be adjusted to fulfil their needs, the front-end to produce the fuel and the back-end to properly manage radioactive waste. AREVA fuel cycle engineering teams have been involved in the design of a variety of industrial plants covering the entire fuel cycle for 50 years. The consistency of the French nuclear policy has been a major factor to acquire and renew the competencies and workforce of AREVA Engineering Business Unit. Our partnership with our customers, French ones but also Japanese, Americans and from other countries, has led us to develop a comprehensive approach of the services that we can deliver, in order to give them the best answer. SGN teams have been involved in the R and D phases in order to take into account the industrialisation aspects as early as possible, and our work does not end with the delivery of the plants; it includes assistance to the operators to optimise and keep their facilities in line with the changing rules and constraints, which ensures the integration of a wide operational experience feedback and the ability to design flexible facilities. This paper will present through our experience how this global approach has been developed and continuously improved and how we are preparing our teams to be ready to answer to the coming needs. (authors)

Joining the Nuclear Renaissance with the Engineering Business Unit of AREVA

International Nuclear Information System (INIS)

Hubert, Nathalie; Menguy, Stephane; Valery, Jean-Francois

2008-01-01

The reality of the nuclear renaissance is no longer a question. All over the world, new nuclear plants are going to be deployed; the whole fuel cycle has to be adjusted to fulfil their needs, the front-end to produce the fuel and the back-end to properly manage radioactive waste. AREVA fuel cycle engineering teams have been involved in the design of a variety of industrial plants covering the entire fuel cycle for 50 years. The consistency of the French nuclear policy has been a major factor to acquire and renew the competencies and workforce of AREVA Engineering Business Unit. Our partnership with our customers, French ones but also Japanese, Americans and from other countries, has led us to develop a comprehensive approach of the services that we can deliver, in order to give them the best answer. SGN teams have been involved in the R and D phases in order to take into account the industrialisation aspects as early as possible, and our work does not end with the delivery of the plants; it includes assistance to the operators to optimise and keep their facilities in line with the changing rules and constraints, which ensures the integration of a wide operational experience feedback and the ability to design flexible facilities. This paper will present through our experience how this global approach has been developed and continuously improved and how we are preparing our teams to be ready to answer to the coming needs. (authors)

Engineering Electromagnetics

International Nuclear Information System (INIS)

Kim, Se Yun

2009-01-01

This book deals with engineering electromagnetics. It contains seven chapters, which treats understanding of engineering electromagnetics such as magnet and electron spin, current and a magnetic field and an electromagnetic wave, Essential tool for engineering electromagnetics on rector and scalar, rectangular coordinate system and curl vector, electrostatic field with coulomb rule and method of electric images, Biot-Savart law, Ampere law and magnetic force, Maxwell equation and an electromagnetic wave and reflection and penetration of electromagnetic plane wave.

SU-E-T-112: An OpenCL-Based Cross-Platform Monte Carlo Dose Engine (oclMC) for Coupled Photon-Electron Transport

International Nuclear Information System (INIS)

Tian, Z; Shi, F; Folkerts, M; Qin, N; Jiang, S; Jia, X

2015-01-01

Purpose: Low computational efficiency of Monte Carlo (MC) dose calculation impedes its clinical applications. Although a number of MC dose packages have been developed over the past few years, enabling fast MC dose calculations, most of these packages were developed under NVidia’s CUDA environment. This limited their code portability to other platforms, hindering the introduction of GPU-based MC dose engines to clinical practice. To solve this problem, we developed a cross-platform fast MC dose engine named oclMC under OpenCL environment for external photon and electron radiotherapy. Methods: Coupled photon-electron simulation was implemented with standard analogue simulation scheme for photon transport and Class II condensed history scheme for electron transport. We tested the accuracy and efficiency of oclMC by comparing the doses calculated using oclMC and gDPM, a previously developed GPU-based MC code on NVidia GPU platform, for a 15MeV electron beam and a 6MV photon beam in a homogenous water phantom, a water-bone-lung-water slab phantom and a half-slab phantom. We also tested code portability of oclMC on different devices, including an NVidia GPU, two AMD GPUs and an Intel CPU. Results: Satisfactory agreements were observed in all photon and electron cases, with ∼0.48%–0.53% average dose differences at regions within 10% isodose line for electron beam cases and ∼0.15%–0.17% for photon beam cases. It took oclMC 3–4 sec to perform transport simulation for electron beam on NVidia Titan GPU and 35–51 sec for photon beam, both with ∼0.5% statistical uncertainty. The computation was 6%–17% slower than gDPM due to the differences in both physics model and development environment, which is considered not significant for clinical applications. In terms of code portability, gDPM only runs on NVidia GPUs, while oclMC successfully runs on all the tested devices. Conclusion: oclMC is an accurate and fast MC dose engine. Its high cross

SU-E-T-112: An OpenCL-Based Cross-Platform Monte Carlo Dose Engine (oclMC) for Coupled Photon-Electron Transport

Energy Technology Data Exchange (ETDEWEB)

Tian, Z; Shi, F; Folkerts, M; Qin, N; Jiang, S; Jia, X [The University of Texas Southwestern Medical Ctr, Dallas, TX (United States)

2015-06-15

Purpose: Low computational efficiency of Monte Carlo (MC) dose calculation impedes its clinical applications. Although a number of MC dose packages have been developed over the past few years, enabling fast MC dose calculations, most of these packages were developed under NVidia’s CUDA environment. This limited their code portability to other platforms, hindering the introduction of GPU-based MC dose engines to clinical practice. To solve this problem, we developed a cross-platform fast MC dose engine named oclMC under OpenCL environment for external photon and electron radiotherapy. Methods: Coupled photon-electron simulation was implemented with standard analogue simulation scheme for photon transport and Class II condensed history scheme for electron transport. We tested the accuracy and efficiency of oclMC by comparing the doses calculated using oclMC and gDPM, a previously developed GPU-based MC code on NVidia GPU platform, for a 15MeV electron beam and a 6MV photon beam in a homogenous water phantom, a water-bone-lung-water slab phantom and a half-slab phantom. We also tested code portability of oclMC on different devices, including an NVidia GPU, two AMD GPUs and an Intel CPU. Results: Satisfactory agreements were observed in all photon and electron cases, with ∼0.48%–0.53% average dose differences at regions within 10% isodose line for electron beam cases and ∼0.15%–0.17% for photon beam cases. It took oclMC 3–4 sec to perform transport simulation for electron beam on NVidia Titan GPU and 35–51 sec for photon beam, both with ∼0.5% statistical uncertainty. The computation was 6%–17% slower than gDPM due to the differences in both physics model and development environment, which is considered not significant for clinical applications. In terms of code portability, gDPM only runs on NVidia GPUs, while oclMC successfully runs on all the tested devices. Conclusion: oclMC is an accurate and fast MC dose engine. Its high cross

Do Undergraduate Engineering Faculty Include Occupational and Public Health and Safety in the Engineering Curriculum?

Science.gov (United States)

Farwell, Dianna; And Others

1995-01-01

The purpose of this study was to determine whether and, if so, why engineering faculty include occupational and public health and safety in their undergraduate engineering courses. Data were collected from 157 undergraduate engineering faculty from 65 colleges of engineering in the United States. (LZ)

Leveling the Playing Field: Teacher Perception of Integrated STEM, Engineering, and Engineering Practices

Science.gov (United States)

Fincher, Bridgette Ann

The purpose of this study was to describe the perceptions and approaches of 14 third-through-fifth grade Arkansan elementary teachers towards integrative engineering and engineering practices during 80 hours of integrated STEM professional development training in the summer and fall of 2014. This training was known as Project Flight. The purpose of the professional development was to learn integrated STEM content related to aviation and to write grade level curriculum units using Wiggins and McTighe's Understanding by Design curriculum framework. The current study builds upon on the original research. Using a mixed method exploratory, embedded QUAL[quan] case study design and a non-experimental convenience sample derived from original 20 participants of Project Flight, this research sought to answer the following question: Does professional development influence elementary teachers' perceptions of the curriculum and instruction of integrated STEM engineering and engineering practices in a 3-to-5 grade level setting? A series of six qualitative and one quantitative sub-questions informed the research of the mixed method question. Hermeneutic content analysis was applied to archival and current qualitative data sets while descriptive statistics, independent t-tests, and repeated measures ANOVA tests were performed on the quantitative data. Broad themes in the teachers' perceptions and understanding of the nature of integrated engineering and engineering practices emerged through triangulation. After the professional development and the teaching of the integrated STEM units, all 14 teachers sustained higher perceptions of personal self-efficacy in their understanding of Next Generation Science Standards (NGSS). The teachers gained understanding of engineering and engineering practices, excluding engineering habits of mind, throughout the professional development training and unit teaching. The research resulted in four major findings specific to elementary engineering

Magnetoresistance oscillations of two-dimensional electron systems in lateral superlattices with structured unit cells

Science.gov (United States)

Gerhardts, Rolf R.

2015-11-01

Model calculations for commensurability oscillations of the low-field magnetoresistance of two-dimensional electron systems (2DES) in lateral superlattices, consisting of unit cells with an internal structure, are compared with recent experiments. The relevant harmonics of the effective modulation potential depend not only on the geometrical structure of the modulated unit cell, but also strongly on the nature of the modulation. While higher harmonics of an electrostatically generated surface modulation are exponentially damped at the position of the 2DES about 90 nm below the surface, no such damping appears for strain-induced modulation generated, e.g., by the deposition of stripes of calixarene resist on the surface before cooling down the sample.

Math, Science, and Engineering Integration in a High School Engineering Course: A Qualitative Study

Science.gov (United States)

Valtorta, Clara G.; Berland, Leema K.

2015-01-01

Engineering in K-12 classrooms has been receiving expanding emphasis in the United States. The integration of science, mathematics, and engineering is a benefit and goal of K-12 engineering; however, current empirical research on the efficacy of K-12 science, mathematics, and engineering integration is limited. This study adds to this growing…

Repurposing Mass-produced Internal Combustion Engines Quantifying the Value and Use of Low-cost Internal Combustion Piston Engines for Modular Applications in Energy and Chemical Engineering Industries

Science.gov (United States)

L'Heureux, Zara E.

This thesis proposes that internal combustion piston engines can help clear the way for a transformation in the energy, chemical, and refining industries that is akin to the transition computer technology experienced with the shift from large mainframes to small personal computers and large farms of individually small, modular processing units. This thesis provides a mathematical foundation, multi-dimensional optimizations, experimental results, an engine model, and a techno-economic assessment, all working towards quantifying the value of repurposing internal combustion piston engines for new applications in modular, small-scale technologies, particularly for energy and chemical engineering systems. Many chemical engineering and power generation industries have focused on increasing individual unit sizes and centralizing production. This "bigger is better" concept makes it difficult to evolve and incorporate change. Large systems are often designed with long lifetimes, incorporate innovation slowly, and necessitate high upfront investment costs. Breaking away from this cycle is essential for promoting change, especially change happening quickly in the energy and chemical engineering industries. The ability to evolve during a system's lifetime provides a competitive advantage in a field dominated by large and often very old equipment that cannot respond to technology change. This thesis specifically highlights the value of small, mass-manufactured internal combustion piston engines retrofitted to participate in non-automotive system designs. The applications are unconventional and stem first from the observation that, when normalized by power output, internal combustion engines are one hundred times less expensive than conventional, large power plants. This cost disparity motivated a look at scaling laws to determine if scaling across both individual unit size and number of units produced would predict the two order of magnitude difference seen here. For the first

SU-F-T-67: Correction Factors for Monitor Unit Verification of Clinical Electron Beams

Energy Technology Data Exchange (ETDEWEB)

Haywood, J [Mercy Health Partners, Muskegon, MI (United States)

2016-06-15

Purpose: Monitor units calculated by electron Monte Carlo treatment planning systems are often higher than TG-71 hand calculations for a majority of patients. Here I’ve calculated tables of geometry and heterogeneity correction factors for correcting electron hand calculations. Method: A flat water phantom with spherical volumes having radii ranging from 3 to 15 cm was created. The spheres were centered with respect to the flat water phantom, and all shapes shared a surface at 100 cm SSD. D{sub max} dose at 100 cm SSD was calculated for each cone and energy on the flat phantom and for the spherical volumes in the absence of the flat phantom. The ratio of dose in the sphere to dose in the flat phantom defined the geometrical correction factor. The heterogeneity factors were then calculated from the unrestricted collisional stopping power for tissues encountered in electron beam treatments. These factors were then used in patient second check calculations. Patient curvature was estimated by the largest sphere that aligns to the patient contour, and appropriate tissue density was read from the physical properties provided by the CT. The resulting MU were compared to those calculated by the treatment planning system and TG-71 hand calculations. Results: The geometry and heterogeneity correction factors range from ∼(0.8–1.0) and ∼(0.9–1.01) respectively for the energies and cones presented. Percent differences for TG-71 hand calculations drop from ∼(3–14)% to ∼(0–2)%. Conclusion: Monitor units calculated with the correction factors typically decrease the percent difference to under actionable levels, < 5%. While these correction factors work for a majority of patients, there are some patient anatomies that do not fit the assumptions made. Using these factors in hand calculations is a first step in bringing the verification monitor units into agreement with the treatment planning system MU.

Computer-aided design system for a complex of problems on calculation and analysis of engineering and economical indexes of NPP power units

International Nuclear Information System (INIS)

Stepanov, V.I.; Koryagin, A.V.; Ruzankov, V.N.

1988-01-01

Computer-aided design system for a complex of problems concerning calculation and analysis of engineering and economical indices of NPP power units is described. In the system there are means for automated preparation and debugging of data base software complex, which realizes th plotted algorithm in the power unit control system. Besides, in the system there are devices for automated preparation and registration of technical documentation

Civil engineering airman at increased risk for injuries and injury-related musculoskeletal disorders.

Science.gov (United States)

Webb, Timothy S; Wells, Timothy S

2011-03-01

With the advent of electronic records, the opportunity to conduct research on workplace-related injuries and musculoskeletal disorders has increased dramatically. The purpose of this study was to examine the United States Air Force Civil Engineering career field to determine if they are negatively impacted by their work environment. Specifically, the objective of this study was to determine if enlisted Civil Engineering Airmen (n = 25,385) were at increased risk for injury or injury-related musculoskeletal disorders compared to enlisted Information Management/Communications Airmen (n = 28,947). Using an historical prospective design, electronic data were assembled and analyzed using Cox's proportional hazards modeling. Models were stratified by gender and adjusted for race/ethnicity, marital status, birth year, and deployment status. Male Civil Engineers were observed to be at greater risk for both inpatient injury-related musculoskeletal disorders (HR = 1.86; 95% CI = 1.54-2.26) and injuries (HR = 1.77; 95% CI = 1.48-2.11), while female Civil Engineers were more than double the risk for both inpatient injury-related musculoskeletal disorders (HR = 2.18; 95% CI = 1.28-3.73) and injuries (HR = 2.22; 95% CI = 1.27-3.88) compared to Information Management/Communications Airmen. Although analyses do not allow exploration of specific causes, they highlight the utility of using electronic data to identify occupations for further evaluation. Based on these results, additional resources were allocated to survey Civil Engineers on their physical work demands and job requirements to identify key problem areas for further study and mitigation. Copyright © 2010 Wiley-Liss, Inc.

2009 UK/US Nuclear Engineering Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Richard Rankin

2009-04-01

This report summarizes the 2009 UK/US Nuclear Engineering Workshop held April 20-21, 2010, in Washington, D.C. to discuss opportunities for nuclear engineering collaboration between researchers in the United States and the United Kingdom.

Efficient photosensitized splitting of the thymine dimer/oxetane unit on its modifying beta-cyclodextrin by a binding electron donor.

Science.gov (United States)

Tang, Wen-Jian; Song, Qin-Hua; Wang, Hong-Bo; Yu, Jing-Yu; Guo, Qing-Xiang

2006-07-07

Two modified beta-cyclodextrins (beta-CDs) with a thymine dimer and a thymine oxetane adduct respectively, TD-CD and Ox-CD, have been prepared, and utilized to bind an electron-rich chromophore, indole or N,N-dimethylaniline (DMA), to form a supramolecular complex. We have examined the photosensitized splitting of the dimer/oxetane unit in TD-CD/Ox-CD by indole or DMA via an electron-transfer pathway, and observed high splitting efficiencies of the dimer/oxetane unit. On the basis of measurements of fluorescence spectra and splitting quantum yields, it is suggested that the splitting reaction occurs in a supramolecular complex by an inclusion interaction between the modified beta-CDs and DMA or indole. The back electron transfer, which leads low splitting efficiencies for the covalently-linked chromophore-dimer/oxetane compounds, is suppressed in the non-covalently-bound complex, and the mechanism has been discussed.

π-Extended Isoindigo-Based Derivative: A Promising Electron-Deficient Building Block for Polymer Semiconductors.

Science.gov (United States)

Xu, Long; Zhao, Zhiyuan; Xiao, Mingchao; Yang, Jie; Xiao, Jian; Yi, Zhengran; Wang, Shuai; Liu, Yunqi

2017-11-22

The exploration of novel electron-deficient building blocks is a key task for developing high-performance polymer semiconductors in organic thin-film transistors. In view of the situation of the lack of strong electron-deficient building blocks, we designed two novel π-extended isoindigo-based electron-deficient building blocks, IVI and F 4 IVI. Owing to the strong electron-deficient nature and the extended π-conjugated system of the two acceptor units, their copolymers, PIVI2T and PF 4 IVI2T, containing 2,2'-bithiophene donor units, are endowed with deep-lying highest occupied molecular orbital (HOMO)/lowest unoccupied molecular orbital (LUMO) energy levels and strong intermolecular interactions. In comparison to PIVI2T, the fluorinated PF 4 IVI2T exhibits stronger intra- and intermolecular interactions, lower HOMO/LUMO energy levels up to -5.74/-4.17 eV, and more ordered molecular packing with a smaller π-π stacking distance of up to 3.53 Å, resulting in an excellent ambipolar transporting behavior and a promising application in logic circuits for PF 4 IVI2T in ambient with hole and electron mobilities of up to 1.03 and 1.82 cm 2 V -1 s -1 , respectively. The results reveal that F 4 IVI is a promising and strong electron-deficient building unit to construct high-performance semiconducting polymers, which provides an insight into the structure-property relationships for the exploration and molecular engineering of excellent electron-deficient building blocks in the field of organic electronics.

Development of a Power Electronics Unit for the Space Station Plasma Contactor

Science.gov (United States)

Hamley, John A.; Hill, Gerald M.; Patterson, Michael J.; Saggio, Joseph, Jr.; Terdan, Fred; Mansell, Justin D.

1994-01-01

A hollow cathode plasma contactor has been baselined as a charge control device for the Space Station (SS) to prevent deleterious interactions of coated structural components with the ambient plasma. NASA LeRC Work Package 4 initiated the development of a plasma contactor system comprised of a Power Electronics Unit (PEU), an Expellant Management Unit (EMU), a command and data interface, and a Plasma Contactor Unit (PCU). A breadboard PEU was designed and fabricated. The breadboard PEU contains a cathode heater and discharge power supply, which were required to operate the PCU, a control and auxiliary power converter, an EMU interface, a command and telemetry interface, and a controller. The cathode heater and discharge supplies utilized a push-pull topology with a switching frequency of 20 kHz and pulse-width-modulated (PWM) control. A pulse ignition circuit derived from that used in arcjet power processors was incorporated in the discharge supply for discharge ignition. An 8088 based microcontroller was utilized in the breadboard model to provide a flexible platform for controller development with a simple command/data interface incorporating a direct connection to SS Mulitplexer/Demultiplexer (MDM) analog and digital I/O cards. Incorporating this in the flight model would eliminate the hardware and software overhead associated with a 1553 serial interface. The PEU autonomously operated the plasma contactor based on command inputs and was successfully integrated with a prototype plasma contactor unit demonstrating reliable ignition of the discharge and steady-state operation.

Economic, energy and GHG emissions performance evaluation of a WhisperGen Mk IV Stirling engine μ-CHP unit in a domestic dwelling

International Nuclear Information System (INIS)

Conroy, G.; Duffy, A.; Ayompe, L.M.

2014-01-01

Highlights: • The performance of a Stirling engine MK IV micro-CHP unit was evaluated in a domestic dwelling in Ireland. • The performance of the micro-CHP was compare to that of a condensing gas boiler. • The micro-CHP unit resulted in an annual cost saving of €180 compared to the condensing gas boiler. • Electricity imported from the grid decreased by 20.8% while CO 2 emissions decreased by 16.1%. • The micro-CHP unit used 2889 kW h of gas more than the condensing gas boiler during one year of operation. - Abstract: This paper presents an assessment of the energy, economic and greenhouse gas emissions performances of a WhisperGen Mk IV Stirling engine μ-CHP unit for use in a conventional house in the Republic of Ireland. The energy performance data used in this study was obtained from a field trial carried out in Belfast, Northern Ireland during the period June 2004–July 2005 by Northern Ireland Electricity and Phoenix Gas working in collaboration with Whispertech UK. A comparative performance analysis between the μ-CHP unit and a condensing gas boiler revealed that the μ-CHP unit resulted in an annual cost saving of €180 with an incremental simple payback period of 13.8 years when compared to a condensing gas boiler. Electricity imported from the grid decreased by 20.8% while CO 2 emissions decreased by 16.1%. The μ-CHP unit used 2889 kW h of gas more than the condensing gas boiler

Engineering Design Skills Coverage in K-12 Engineering Program Curriculum Materials in the USA

Science.gov (United States)

Chabalengula, Vivien M.; Mumba, Frackson

2017-01-01

The current "K-12 Science Education framework" and "Next Generation Science Standards" (NGSS) in the United States emphasise the integration of engineering design in science instruction to promote scientific literacy and engineering design skills among students. As such, many engineering education programmes have developed…

Preliminary Performance Data on Westinghouse Electronic Power Regulator Operating on J34-WE-32 Turbojet Engine in Altitude Wind Tunnel

Science.gov (United States)

Ketchum, James R.; Blivas, Darnold; Pack, George J.

1950-01-01

The behavior of the Westinghouse electronic power regulator operating on a J34-WE-32 turbojet engine was investigated in the NACA Lewis altitude wind tunnel at the request of the Bureau of Aeronautics, Department of the Navy. The object of the program was to determine the, steady-state stability and transient characteristics of the engine under control at various altitudes and ram pressure ratios, without afterburning. Recordings of the response of the following parameters to step changes in power lever position throughout the available operating range of the engine were obtained; ram pressure ratio, compressor-discharge pressure, exhaust-nozzle area, engine speed, turbine-outlet temperature, fuel-valve position, jet thrust, air flow, turbine-discharge pressure, fuel flow, throttle position, and boost-pump pressure. Representative preliminary data showing the actual time response of these variables are presented. These data are presented in the form of reproductions of oscillographic traces.

Reduction of secondary electron yield for E-cloud mitigation by laser ablation surface engineering

Energy Technology Data Exchange (ETDEWEB)

Valizadeh, R., E-mail: reza.valizadeh@stfc.ac.uk [ASTeC, STFC Daresbury Laboratory, Warrington WA4 4AD (United Kingdom); Malyshev, O.B. [ASTeC, STFC Daresbury Laboratory, Warrington WA4 4AD (United Kingdom); Wang, S. [ASTeC, STFC Daresbury Laboratory, Warrington WA4 4AD (United Kingdom); Department of Physics, Loughborough University, Loughborough LE11 3TU (United Kingdom); Sian, T. [ASTeC, STFC Daresbury Laboratory, Warrington WA4 4AD (United Kingdom); The Photon Science Institute, The University of Manchester, Manchester M13 9PL (United Kingdom); Cropper, M.D. [Department of Physics, Loughborough University, Loughborough LE11 3TU (United Kingdom); Sykes, N. [Micronanics Ltd., Didcot, Oxon OX11 0QX (United Kingdom)

2017-05-15

Highlights: • SEY below 1 can be achieved with Laser ablation surface engineering. • SEY <1 surface can be produced with different types of nanosecond lasers. • Both microstructure (groves) and nano-structures are playing a role in reducing SEY. - Abstract: Developing a surface with low Secondary Electron Yield (SEY) is one of the main ways of mitigating electron cloud and beam-induced electron multipacting in high-energy charged particle accelerators. In our previous publications, a low SEY < 0.9 for as-received metal surfaces modified by a nanosecond pulsed laser was reported. In this paper, the SEY of laser-treated blackened copper has been investigated as a function of different laser irradiation parameters. We explore and study the influence of micro- and nano-structures induced by laser surface treatment in air of copper samples as a function of various laser irradiation parameters such as peak power, laser wavelength (λ = 355 nm and 1064 nm), number of pulses per point (scan speed and repetition rate) and fluence, on the SEY. The surface chemical composition was determined by x-ray photoelectron spectroscopy (XPS) which revealed that heating resulted in diffusion of oxygen into the bulk and induced the transformation of CuO to sub-stoichiometric oxide. The surface topography was examined with high resolution scanning electron microscopy (HRSEM) which showed that the laser-treated surfaces are dominated by microstructure grooves and nanostructure features.

No money printing machine. The market for cogeneration units with a Stirling engine begins to increase; Keine Gelddruckmaschinen. Markt fuer Stirling-KWK-Geraete kommt in Bewegung

Energy Technology Data Exchange (ETDEWEB)

Schmid, Wolfgang

2012-10-15

The serial production of micro combined heat and power units with a Stirling engine is started. However, it is becoming apparent, that from economic reasons units of the 1-kW{sub el.}-class designed for single-family houses and two-family houses are increasingly used as a base load unit in multi-family houses and small trades.

Cummins Engine Company B5.9 Propane Engine Development, Certification, and Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

The ADEPT Group, Inc. (Los Angeles, California)

1998-12-18

The objective of this project was to successfuly develop and certify an LPG-dedicated medium-duty original equipment manufacturer (OEM) engine that could be put into production. The engine was launched into production in 1994, and more than 800 B5.9G engines are now in service in the United States and abroad. This engine is now offered by more than 30 bus and truck OEMs.

Thermal engineering and micro-technology; Thermique et microtechnologie

Energy Technology Data Exchange (ETDEWEB)

Kandlikar, S. [Rochester Inst. of Tech., NY (United States); Luo, L. [Institut National Polytechnique, 54 - Nancy (France); Gruss, A. [CEA Grenoble, GRETH, 38 (France); Wautelet, M. [Mons Univ. (Belgium); Gidon, S. [CEA Grenoble, Lab. d' Electronique et de Technologie de l' Informatique (LETI), 38 (France); Gillot, C. [Ecole Nationale Superieure d' Ingenieurs Electriciens de Grenoble, 38 - Saint Martin d' Heres (France)]|[CEA Grenoble, Lab. Electronique et de Technologie de l' Informatique (LETI), 38 (France); Therme, J.; Marvillet, Ch.; Vidil, R. [CEA Grenoble, 38 (France); Dutartre, D. [ST Microelectronique, France (France); Lefebvre, Ph. [SNECMA, 75 - Paris (France); Lallemand, M. [Institut National des Sciences Appliquees (INSA), 69 - Villeurbanne (France); Colin, S. [Institut National des Sciences Appliquees (INSA), 31 - Toulouse (France); Joulin, K. [Ecole Nationale Superieure de Mecanique et d' Aerotechnique (ENSMA), 86 - Poitiers (France); Gad el Hak, M. [Virginia Univ., Charlottesville, VA (United States)

2003-07-01

This document gathers the abstracts and transparencies of 5 invited conferences of this congress of the SFT about heat transfers and micro-technologies: Flow boiling in microchannels: non-dimensional groups and heat transfer mechanisms (S. Kandlikar); Intensification and multi-scale process units (L. Luo and A. Gruss); Macro-, micro- and nano-systems: different physics? (M. Wautelet); micro-heat pipes (M. Lallemand); liquid and gas flows inside micro-ducts (S. Colin). The abstracts of the following presentations are also included: Electro-thermal writing of nano-scale memory points in a phase change material (S. Gidon); micro-technologies for cooling in micro-electronics (C. Gillot); the Minatec project (J. Therme); importance and trends of thermal engineering in micro-electronics (D. Dutartre); Radiant heat transfers at short length scales (K. Joulain); Momentum and heat transfer in micro-electromechanical systems (M. Gad-el-Hak). (J.S.)

About the information depth of backscattered electron imaging

Czech Academy of Sciences Publication Activity Database

Piňos, Jakub; Mikmeková, Šárka; Frank, Luděk

2017-01-01

Roč. 266, č. 3 (2017), s. 335-342 ISSN 0022-2720 Institutional support: RVO:68081731 Keywords : backscattered electrons * information depth * penetration of electrons Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering OBOR OECD: Materials engineering Impact factor: 1.692, year: 2016

Accelerating VASP electronic structure calculations using graphic processing units

KAUST Repository

Hacene, Mohamed

2012-08-20

We present a way to improve the performance of the electronic structure Vienna Ab initio Simulation Package (VASP) program. We show that high-performance computers equipped with graphics processing units (GPUs) as accelerators may reduce drastically the computation time when offloading these sections to the graphic chips. The procedure consists of (i) profiling the performance of the code to isolate the time-consuming parts, (ii) rewriting these so that the algorithms become better-suited for the chosen graphic accelerator, and (iii) optimizing memory traffic between the host computer and the GPU accelerator. We chose to accelerate VASP with NVIDIA GPU using CUDA. We compare the GPU and original versions of VASP by evaluating the Davidson and RMM-DIIS algorithms on chemical systems of up to 1100 atoms. In these tests, the total time is reduced by a factor between 3 and 8 when running on n (CPU core + GPU) compared to n CPU cores only, without any accuracy loss. © 2012 Wiley Periodicals, Inc.

Accelerating VASP electronic structure calculations using graphic processing units

KAUST Repository

Hacene, Mohamed; Anciaux-Sedrakian, Ani; Rozanska, Xavier; Klahr, Diego; Guignon, Thomas; Fleurat-Lessard, Paul

2012-01-01

We present a way to improve the performance of the electronic structure Vienna Ab initio Simulation Package (VASP) program. We show that high-performance computers equipped with graphics processing units (GPUs) as accelerators may reduce drastically the computation time when offloading these sections to the graphic chips. The procedure consists of (i) profiling the performance of the code to isolate the time-consuming parts, (ii) rewriting these so that the algorithms become better-suited for the chosen graphic accelerator, and (iii) optimizing memory traffic between the host computer and the GPU accelerator. We chose to accelerate VASP with NVIDIA GPU using CUDA. We compare the GPU and original versions of VASP by evaluating the Davidson and RMM-DIIS algorithms on chemical systems of up to 1100 atoms. In these tests, the total time is reduced by a factor between 3 and 8 when running on n (CPU core + GPU) compared to n CPU cores only, without any accuracy loss. © 2012 Wiley Periodicals, Inc.

Electronics and Telemetry Engineering and Test Facility

Data.gov (United States)

Federal Laboratory Consortium — The Electronics Laboratory is a fully equipped facility providing the capability to support electronic product development from highly complex weapon system sensors,...

Semiconductor Physical Electronics

CERN Document Server

Li, Sheng

2006-01-01

Semiconductor Physical Electronics, Second Edition, provides comprehensive coverage of fundamental semiconductor physics that is essential to an understanding of the physical and operational principles of a wide variety of semiconductor electronic and optoelectronic devices. This text presents a unified and balanced treatment of the physics, characterization, and applications of semiconductor materials and devices for physicists and material scientists who need further exposure to semiconductor and photonic devices, and for device engineers who need additional background on the underlying physical principles. This updated and revised second edition reflects advances in semicondutor technologies over the past decade, including many new semiconductor devices that have emerged and entered into the marketplace. It is suitable for graduate students in electrical engineering, materials science, physics, and chemical engineering, and as a general reference for processing and device engineers working in the semicondi...

Near-memory data reorganization engine

Science.gov (United States)

Gokhale, Maya; Lloyd, G. Scott

2018-05-08

A memory subsystem package is provided that has processing logic for data reorganization within the memory subsystem package. The processing logic is adapted to reorganize data stored within the memory subsystem package. In some embodiments, the memory subsystem package includes memory units, a memory interconnect, and a data reorganization engine ("DRE"). The data reorganization engine includes a stream interconnect and DRE units including a control processor and a load-store unit. The control processor is adapted to execute instructions to control a data reorganization. The load-store unit is adapted to process data move commands received from the control processor via the stream interconnect for loading data from a load memory address of a memory unit and storing data to a store memory address of a memory unit.

Newnes electronics toolkit

CERN Document Server

Phillips, Geoff

2013-01-01

Newnes Electronics Toolkit brings together fundamental facts, concepts, and applications of electronic components and circuits, and presents them in a clear, concise, and unambiguous format, to provide a reference book for engineers. The book contains 10 chapters that discuss the following concepts: resistors, capacitors, inductors, semiconductors, circuit concepts, electromagnetic compatibility, sound, light, heat, and connections. The engineer's job does not end when the circuit diagram is completed; the design for the manufacturing process is just as important if volume production is to be

A Self-Powered Wearable Noninvasive Electronic-Skin for Perspiration Analysis Based on Piezo-Biosensing Unit Matrix of Enzyme/ZnO Nanoarrays.

Science.gov (United States)

Han, Wuxiao; He, Haoxuan; Zhang, Linlin; Dong, Chuanyi; Zeng, Hui; Dai, Yitong; Xing, Lili; Zhang, Yan; Xue, Xinyu

2017-09-06

The emerging multifunctional flexible electronic-skin for establishing body-electric interaction can enable real-time monitoring of personal health status as a new personalized medicine technique. A key difficulty in the device design is the flexible power supply. Here a self-powered wearable noninvasive electronic-skin for perspiration analysis has been realized on the basis of a piezo-biosensing unit matrix of enzyme/ZnO nanoarrays. The electronic-skin can detect lactate, glucose, uric acid, and urea in the perspiration, and no outside electrical power supply or battery is used in the biosensing process. The piezoelectric impulse of the piezo-biosensing units serves as the power supply and the data biosensor. The working mechanism can be ascribed to the piezoelectric-enzymatic-reaction coupling effect of enzyme/ZnO nanowires. The electronic-skin can real-time/continuously monitor the physiological state of a runner through analyzing the perspiration on his skin. This approach can promote the development of a new-type of body electric and self-powered biosensing electronic-skin.

Automotive Stirling Engine Development Program

Science.gov (United States)

Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Antonelli, M. (Editor)

1983-01-01

Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

ESSE: Engineering Super Simulation Emulation for Virtual Reality Systems Environment

International Nuclear Information System (INIS)

Suh, Kune Y.; Yeon, Choul W.

2008-01-01

The trademark 4 + D Technology TM based Engineering Super Simulation Emulation (ESSE) is introduced. ESSE resorting to three-dimensional (3D) Virtual Reality (VR) technology pledges to provide with an interactive real-time motion, sound and tactile and other forms of feedback in the man machine systems environment. In particular, the 3D Virtual Engineering Neo cybernetic Unit Soft Power (VENUS) adds a physics engine to the VR platform so as to materialize a physical atmosphere. A close cooperation system and prompt information share are crucial, thereby increasing the necessity of centralized information system and electronic cooperation system. VENUS is further deemed to contribute towards public acceptance of nuclear power in general, and safety in particular. For instance, visualization of nuclear systems can familiarize the public in answering their questions and alleviating misunderstandings on nuclear power plants answering their questions and alleviating misunderstandings on nuclear power plants (NPPs) in general, and performance, security and safety in particular. An in-house flagship project Systemic Three-dimensional Engine Platform Prototype Engineering (STEPPE) endeavors to develop the Systemic Three-dimensional Engine Platform (STEP) for a variety of VR applications. STEP is home to a level system providing the whole visible scene of virtual engineering of man machine system environment. The system is linked with video monitoring that provides a 3D Computer Graphics (CG) visualization of major events. The database linked system provides easy access to relevant blueprints. The character system enables the operators easy access to visualization of major events. The database linked system provides easy access to relevant blueprints. The character system enables the operators to access the virtual systems by using their virtual characters. Virtually Engineered NPP Informative systems by using their virtual characters. Virtually Engineered NPP Informative

Standardized Curriculum for Diesel Engine Mechanics.

Science.gov (United States)

Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

Standardized curricula are provided for two courses for the secondary vocational education program in Mississippi: diesel engine mechanics I and II. The eight units in diesel engine mechanics I are as follows: orientation; shop safety; basic shop tools; fasteners; measurement; engine operating principles; engine components; and basic auxiliary…

Experimental and theoretical investigations of the electronic band structure of metal-organic frameworks of HKUST-1 type

Science.gov (United States)

Gu, Zhi-Gang; Heinke, Lars; Wöll, Christof; Neumann, Tobias; Wenzel, Wolfgang; Li, Qiang; Fink, Karin; Gordan, Ovidiu D.; Zahn, Dietrich R. T.

2015-11-01

The electronic properties of metal-organic frameworks (MOFs) are increasingly attracting the attention due to potential applications in sensor techniques and (micro-) electronic engineering, for instance, as low-k-dielectric in semiconductor technology. Here, the band gap and the band structure of MOFs of type HKUST-1 are studied in detail by means of spectroscopic ellipsometry applied to thin surface-mounted MOF films and by means of quantum chemical calculations. The analysis of the density of states, the band structure, and the excitation spectrum reveal the importance of the empty Cu-3d orbitals for the electronic properties of HKUST-1. This study shows that, in contrast to common belief, even in the case of this fairly "simple" MOF, the excitation spectra cannot be explained by a superposition of "intra-unit" excitations within the individual building blocks. Instead, "inter-unit" excitations also have to be considered.

Electron beam application for regeneration of catalysts used in refinery cracking units

International Nuclear Information System (INIS)

Kondo, Fernando Mantovani; Duarte, Celina Lopes; Sato, Ivone Mulako; Salvador, Vera Lucia Ribeiro; Calvo, Wilson Aparecido Parejo

2013-01-01

A catalyst is a substance that alters the rate of a reaction. The process of catalysis is essential to the modern day manufacturing industry, mainly in Fluid Catalytic Cracking Process (FCC) units. However, long-term exploitation of oil and gas processing catalysts leads to formation of carbon-and sulfur-containing structures of coke and dense products on the catalyst surface. They block reactive catalyst sites and reduce the catalytic activity. The main advantage of radiation processing by electron beam (EB) and gamma rays is chain cracking reaction in crude oil. Otherwise, under exposure to ionic radiation, considerable structure modification of equilibrium silica-alumina catalyst from FCC process may occur, in addition to the removal of impurities. The conditions applied in the irradiation range (20-150 kGy) of gamma rays and electron beam were not sufficient to alter the structure of the catalyst, whether for removal of the contaminant nickel, a major contaminant of the FCC catalyst, either to rupture of the crystalline structure either for the future reutilization of chemical elements. Attenuated Total Reflectance - Fourier Transform Infrared Spectroscopy (ATR-FTIR) and Energy Dispersive X-Ray Fluorescence Spectrometry (EDXRFS) analysis were used to characterize and evaluate effects of radiation processing on equilibrium catalysts purification. To evaluate and comprehend the reactive catalyst sites, Scanning Electron Microscopy (SEM) and particle size distribution analyses were carried out. (author)

Continuous CS Analysis of Using the SIEM to Introduction to Computer Programming Education in the School of Engineering Evening Division at the Department of Electrical and Electronic Engineering

Science.gov (United States)

Dohi, Shinichi; Miyakawa, Osamu; Konno, Noriko

In order to improve students’ motivation, the SIEM (School of Information Environment Method) which is the education method for the introduction of the computer programming education was developed. We focus on students’ motivation, and we have measured students’ motivation as the educational effects. After the SIEM was developed in the School of Information Environment, it applied to introduction to the computer programming education in the School of Engineering Evening Division at the Department of Electrical and Electronic Engineering. It is effective for the improvement of students’ motivation. By adding the Customer Satisfaction Analysis to the SIEM Analysis, it was able to clarify the priority level of the SIEM assessment item. In this paper, we describe results of the Customer Satisfaction Analysis.

Near Earth Asteroid Solar Sail Engineering Development Unit Test Program

Science.gov (United States)

Lockett, Tiffany Russell; Few, Alexander; Wilson, Richard

2017-01-01

The Near Earth Asteroid (NEA) Scout project is a 30x20x10cm (6U) cubesat reconnaissance mission to investigate a near Earth asteroid utilizing an 86m2 solar sail as the primary propulsion system. This will be the largest solar sail NASA will launch to date. NEA Scout is a secondary payload currently manifested on the maiden voyage of the Space Launch System in 2018. In development of the solar sail subsystem, design challenges were identified and investigated for packaging within a 6U form factor and deployment in cis-lunar space. Analysis furthered understanding of thermal, stress, and dynamics of the stowed system and matured an integrated sail membrane model for deployed flight dynamics. This paper will address design, fabrication, and lessons learned from the NEA Scout solar sail subsystem engineering development unit. From optical properties of the sail material to folding and spooling the single 86m2 sail, the team has developed a robust deployment system for the solar sail. This paper will also address expected and received test results from ascent vent, random vibration, and deployment tests.

Electronic components

CERN Document Server

Colwell, Morris A

1976-01-01

Electronic Components provides a basic grounding in the practical aspects of using and selecting electronics components. The book describes the basic requirements needed to start practical work on electronic equipment, resistors and potentiometers, capacitance, and inductors and transformers. The text discusses semiconductor devices such as diodes, thyristors and triacs, transistors and heat sinks, logic and linear integrated circuits (I.C.s) and electromechanical devices. Common abbreviations applied to components are provided. Constructors and electronics engineers will find the book useful

Concept of Six Stroke Engine

OpenAIRE

P.Naresh

2015-01-01

One of the most difficult challenges in engine technology today is the urgent need to increase engine thermal efficiency. Higher efficiencies mean less fuel consumption and lower atmospheric emissions per unit of work produced by the engine. In 1862 a Frenchman Alphouse Beau de Rochas gives his theory regarding the ideal cycle of the internal combustion engine. This theory is applied by a German engineer named Nikolaus A. Otto, who firstly built a successful four-stroke SI engine in 1876. The...

Electronic logic circuits

CERN Document Server

Gibson, J

2013-01-01

Most branches of organizing utilize digital electronic systems. This book introduces the design of such systems using basic logic elements as the components. The material is presented in a straightforward manner suitable for students of electronic engineering and computer science. The book is also of use to engineers in related disciplines who require a clear introduction to logic circuits. This third edition has been revised to encompass the most recent advances in technology as well as the latest trends in components and notation. It includes a wide coverage of application specific integrate

Proposal for future trend of engine mechatronics in marine diesel engines

Energy Technology Data Exchange (ETDEWEB)

Higashino, Ichiro; Higashi, Tadanori (Ashiya Univ., Hyogo (Japan))

1989-02-01

A future condition of engine mechatronics in the marine diesel engines was proposed. As a result of investigation, it was understood that the diesel engine, as mechatronicalized for the land plant use with an already high technology, is done for the marine use as an amplification of applying that for the land plant use. The marine diesel engine, if only maintaining the good performance in all the operating conditions, is low in mechatronicalized effect as compared with that for the land plant use. Particularly, there is no expectation of effect on the large ship. While as a reply to an inquiry to 100 enterprises, expectation, in the all automation electronic control, was of, in the order of expectation, reliability, automation, energy and labor saving, and anomaly diagnosis, which showed the most desired expectation to be of reliability. In other words, the reliability is presently one of the weakest points to apply the electronic control, which inversely requires the solution for the reliability. However there can be no expectation of decrease in fuel coat due to the mechatronicalization. 13 refs., 1 tab.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXII, I--MAINTAINING THE FUEL SYSTEM (PART I)--CUMMINS DIESEL ENGINE, II--UNDERSTANDING THE DIFFERENTIAL.

Science.gov (United States)

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE FUNCTION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM AND DIFFERENTIAL DRIVE UNITS USED IN DIESEL POWERED VEHICLES. TOPICS ARE (1) FUEL SYSTEM COMPARISONS, (2) FUEL SYSTEM SUPPLY COMPONENTS, (3) FUEL SUPPLY SECTION MAINTENANCE, (4) FUNCTION OF THE DIFFERENTIAL,…

Optical Coating Performance and Thermal Structure Design for Heat Reflectors of JWST Electronic Control Unit

Science.gov (United States)

Quijada, Manuel A.; Threat, Felix; Garrison, Matt; Perrygo, Chuck; Bousquet, Robert; Rashford, Robert

2008-01-01

The James Webb Space Telescope (JWST) consists of an infrared-optimized Optical Telescope Element (OTE) that is cooled down to 40 degrees Kelvin. A second adjacent component to the OTE is the Integrated Science Instrument Module, or ISIM. This module includes the electronic compartment, which provides the mounting surfaces and ambient thermally controlled environment for the instrument control electronics. Dissipating the 200 watts generated from the ISIM structure away from the OTE is of paramount importance so that the spacecraft's own heat does not interfere with the infrared light detected from distant cosmic sources. This technical challenge is overcome by a thermal subsystem unit that provides passive cooling to the ISIM control electronics. The proposed design of this thermal radiator consists of a lightweight structure made out of composite materials and low-emittance metal coatings. In this paper, we will present characterizations of the coating emittance, bidirectional reflectance, and mechanical structure design that will affect the performance of this passive cooling system.

Diesel engines for independent power producers

International Nuclear Information System (INIS)

Berc, Dj.

1999-01-01

During recent years an increasing demand has been experienced in the stationary diesel engine market for 10-70 MW diesel units. For larger units this demand is being met by two-stroke low-speed crosshead uniflow scavenged diesel engines, capable of burning almost any fuel available on the market, both liquid of gaseous. The paper deals with service experience gained from such engines and their fuel capability. Examples of actual installations for IPPs and captive plants, together with an example of a typical feasibility study of such plants, is presented in the Appendix. (author)

Dynamic model of Stirling engine crank mechanism with connected electric generator

Directory of Open Access Journals (Sweden)

Vlach R.

2009-06-01

Full Text Available This paper treats of a numerical dynamic model of Stirling engine crank mechanism. The model is included in the complex model of combined heat and power unit. The unit is composed of the Stirling engine and of attached three-phase synchronous generator. This generator should start the Stirling engine in motor mode as well. It is necessary to combine the crank shaft dynamic model and the complete thermal model of Stirling engine for simulations and analyses of engine run. Our aim is to create a dynamics model which takes into account the parameters of crankshaft, piston rods, pistons, and attached generator. For unit working, the electro-mechanical behaviour of generator is also important. That is why we experimentally verified the parameters of generator. The measured characteristics are used in a complex model of heat and power unit. Moreover, it is also possible to determine the Stirling engine torque by the help of these electro-mechanical characteristics. These values can be used e. g. for determination of optimal engine working point or for unit control.

A nuclear power plant system engineering workstation

International Nuclear Information System (INIS)

Mason, J.H.; Crosby, J.W.

1989-01-01

System engineers offer an approach for effective technical support for operation and maintenance of nuclear power plants. System engineer groups are being set up by most utilities in the United States. Institute of Nuclear Power operations (INPO) and U.S. Nuclear Regulatory Commission (NRC) have endorsed the concept. The INPO Good Practice and a survey of system engineer programs in the southeastern United States provide descriptions of system engineering programs. The purpose of this paper is to describe a process for developing a design for a department-level information network of workstations for system engineering groups. The process includes the following: (1) application of a formal information engineering methodology, (2) analysis of system engineer functions and activities; (3) use of Electric Power Research Institute (EPRI) Plant Information Network (PIN) data; (4) application of the Information Engineering Workbench. The resulting design for this system engineer workstation can provide a reference for design of plant-specific systems

Preliminary test of remote manual instrumentation & control type system for vacuum unit of 350 KeV / 10 mA electron beam machine

International Nuclear Information System (INIS)

Sudiyanto

2003-01-01

Remote manual instrumentation & control type for vacuum unit of 350 KeV/10 mA Electron Beam Machine is being completed. The system consisting of a remote manual controlled and a remote acquisition system. A remote manual (50 m) controlled is based on the on/off status of 220 Volt terminal supply for pneumatic valves and vacuum pumps, in this case the power supply switch of pneumatic valves and pumps have already been selected On. Remote acquisition of vacuum level can be done by using a CCTV camera which is place in front of the panning gauge and TGP.300 Balzer unit.The CCTV system equipped with 6 cameras, one TV monitor and a multiplexer unit to arranged a selected picture on it. One of the camera was mounted on the rotator unit, it can be controlled (rotating left / right) for different monitoring orientations required by using infrared controller. A trial test of the remote manual control system for vacuum unit of the Electron Beam Machine showed a good performance. (author)

Multi-Mission System Architecture Platform: Design and Verification of the Remote Engineering Unit

Science.gov (United States)

Sartori, John

2005-01-01

The Multi-Mission System Architecture Platform (MSAP) represents an effort to bolster efficiency in the spacecraft design process. By incorporating essential spacecraft functionality into a modular, expandable system, the MSAP provides a foundation on which future spacecraft missions can be developed. Once completed, the MSAP will provide support for missions with varying objectives, while maintaining a level of standardization that will minimize redesign of general system components. One subsystem of the MSAP, the Remote Engineering Unit (REU), functions by gathering engineering telemetry from strategic points on the spacecraft and providing these measurements to the spacecraft's Command and Data Handling (C&DH) subsystem. Before the MSAP Project reaches completion, all hardware, including the REU, must be verified. However, the speed and complexity of the REU circuitry rules out the possibility of physical prototyping. Instead, the MSAP hardware is designed and verified using the Verilog Hardware Definition Language (HDL). An increasingly popular means of digital design, HDL programming provides a level of abstraction, which allows the designer to focus on functionality while logic synthesis tools take care of gate-level design and optimization. As verification of the REU proceeds, errors are quickly remedied, preventing costly changes during hardware validation. After undergoing the careful, iterative processes of verification and validation, the REU and MSAP will prove their readiness for use in a multitude of spacecraft missions.

Global Journal of Engineering Research

African Journals Online (AJOL)

The Global Journal of Engineering Research is aimed at promoting research in all areas of Engineering Research including Mechanical, Civil, Electrical, Chemical, Electronics, Geological etc. Visit the Global Journal Series website here: http://www.globaljournalseries.com/ ...

Effectiveness of Prepared Instruction Units in Teaching the Principles of Internal Combustion Engine Operation and Maintenance. Technical Bulletin No. 192.

Science.gov (United States)

Jacobs, Clinton O.

The report is an evaluation of the effectiveness of the 12 instructional units developed around the use of the Briggs-Stratton Model 80302, 3HP, 8 cu. in. displacement engine having a fuel induction system similar in construction to farm tractor types. The evaluation procedure used was the "one-group Pre-test and Post-test" research method. The…

Journal of Modeling, Design and Management of Engineering ...

African Journals Online (AJOL)

The Journal of Modeling, Design & Management of Engineering Systems publishes original ... systems Electronic/Electrical systems Engineering management systems Fuel and Energy systems Information Technology ... systems Pubic Health systems Software Engineering systems Systems and Industrial Engineering ...

Electronics. Module 2: Fundamentals of Electronics. Instructor's Guide.

Science.gov (United States)

Everett, Jim

This guide contains instructor's materials for a nine-unit secondary school course on fundamentals of electronics. The units are conductors, insulators, semiconductors, and atomic structure; basic concepts and sources of electrical quantities; Ohm's Law; units and conversions; use of multimeters; circuits; electromagnetics and electrostatics;…

Conversion from Engineering Units to Telemetry Counts on Dryden Flight Simulators

Science.gov (United States)

Fantini, Jay A.

1998-01-01

Dryden real-time flight simulators encompass the simulation of pulse code modulation (PCM) telemetry signals. This paper presents a new method whereby the calibration polynomial (from first to sixth order), representing the conversion from counts to engineering units (EU), is numerically inverted in real time. The result is less than one-count error for valid EU inputs. The Newton-Raphson method is used to numerically invert the polynomial. A reverse linear interpolation between the EU limits is used to obtain an initial value for the desired telemetry count. The method presented here is not new. What is new is how classical numerical techniques are optimized to take advantage of modem computer power to perform the desired calculations in real time. This technique makes the method simple to understand and implement. There are no interpolation tables to store in memory as in traditional methods. The NASA F-15 simulation converts and transmits over 1000 parameters at 80 times/sec. This paper presents algorithm development, FORTRAN code, and performance results.

Reliability and safety engineering

CERN Document Server

Verma, Ajit Kumar; Karanki, Durga Rao

2016-01-01

Reliability and safety are core issues that must be addressed throughout the life cycle of engineering systems. Reliability and Safety Engineering presents an overview of the basic concepts, together with simple and practical illustrations. The authors present reliability terminology in various engineering fields, viz.,electronics engineering, software engineering, mechanical engineering, structural engineering and power systems engineering. The book describes the latest applications in the area of probabilistic safety assessment, such as technical specification optimization, risk monitoring and risk informed in-service inspection. Reliability and safety studies must, inevitably, deal with uncertainty, so the book includes uncertainty propagation methods: Monte Carlo simulation, fuzzy arithmetic, Dempster-Shafer theory and probability bounds. Reliability and Safety Engineering also highlights advances in system reliability and safety assessment including dynamic system modeling and uncertainty management. Cas...

Electronic control of a 4-speed automatic transmission with lock-up clutch

Energy Technology Data Exchange (ETDEWEB)

Schwab, M.

1984-01-01

The paper describes the electronic control of an automatic 4-speed transmission with lock-up clutch. As compared to purely hydraulically controlled transmissions, this control offers a clearly improved quality of shifting and the possibility of achieving improvements in fuel consumption thanks to a special economy program. The electronic control unit is a Bosch MOTRONIC which has been expanded to include the functions of transmission control. A special feature is the engine torque control which is implemented by way of retarding the ignition when shifting. This opens up an additional degree of freedom for optimizing a transmission in terms of shift comfort, life of the friction elements and the power which can be transmitted.

Design electronic of manual control for cobalt unit Alcyon II of the National Center of Radiotherapy

International Nuclear Information System (INIS)

Morraz V, E.; Campos, X.

2002-01-01

A manual control for the cobalt unit, of French production, it was designed by the team of electronic of the national center of radiotherapy with materials found in the national trade. The control has the same characteristics that the original one and it is also adapted a switch from which you can control the lights of the room of the cobalt

Neurophysiology and neural engineering: a review.

Science.gov (United States)

Prochazka, Arthur

2017-08-01

Neurophysiology is the branch of physiology concerned with understanding the function of neural systems. Neural engineering (also known as neuroengineering) is a discipline within biomedical engineering that uses engineering techniques to understand, repair, replace, enhance, or otherwise exploit the properties and functions of neural systems. In most cases neural engineering involves the development of an interface between electronic devices and living neural tissue. This review describes the origins of neural engineering, the explosive development of methods and devices commencing in the late 1950s, and the present-day devices that have resulted. The barriers to interfacing electronic devices with living neural tissues are many and varied, and consequently there have been numerous stops and starts along the way. Representative examples are discussed. None of this could have happened without a basic understanding of the relevant neurophysiology. I also consider examples of how neural engineering is repaying the debt to basic neurophysiology with new knowledge and insight. Copyright © 2017 the American Physiological Society.

RE-1000 free-piston Stirling engine update

Science.gov (United States)

Schreiber, J. G.

1985-01-01

A free piston Stirling engine was tested. The tests performed over the past several years on the single cylinder engine were designed to investigate the dynamics of a free piston Stirling engine. The data are intended to be used primarily for computer code validation. The tests designed to investigate the sensitivity of the engine performance to variations in working space pressure, heater and cooler temperatures, regenerator porosity, power piston mass and displacer dynamics were completed. In addition, some data were recorded with alternate working fluids. A novel resonant balance system for the engine was also tested. Some preliminary test results of the tests performed are presented along with an outline of future tests to be run with the engine coupled to a hydraulic output unit. A description of the hydraulic output unit is given.

Safety analysis report for the mixed waste storage facility and portable storage units at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Peatross, R.

1997-01-01

The Mixed Waste Storage Facility (MWSF) including the Portable Storage Units (PSUs) is a government-owned contractor-operated facility located at the Idaho National Engineering Laboratory (INEL). Lockheed Martin Idaho Technologies Company (LMITCO) is the current operating contractor and facility Architect/Engineer as of September 1996. The operating contractor is referred to as open-quotes the Companyclose quotes or open-quotes Companyclose quotes throughout this document. Oversight of MWSF is provided by the Department of Energy Idaho Operations Office (DOE-ID). The MWSF is located in the Power Burst Facility (PBF) Waste Reduction Operations Complex (WROC) Area, approximately 10.6 km (6.6 mi) from the southern INEL boundary and 4 km (2.5 mi) from U.S. Highway 20

Diesel Technology: Engines. [Teacher and Student Editions.

Science.gov (United States)

Barbieri, Dave; Miller, Roger; Kellum, Mary

Competency-based teacher and student materials on diesel engines are provided for a diesel technology curriculum. Seventeen units of instruction cover the following topics: introduction to engine principles and procedures; engine systems and components; fuel systems; engine diagnosis and maintenance. The materials are based on the…

Engineering education for youth: Diverse elementary school students' experiences with engineering design

Science.gov (United States)

Hegedus, Theresa

Lingering concerns over the persistent achievement gap amidst the trend of an increasingly diverse society have been compounded by calls from the Oval Office, the National Science Board, and nationwide media to also address our current creativity crisis. Now, more than ever, we have a responsibility to produce a STEM-capable (science, technology, engineering, and mathematics) workforce to meet the demands of our rapidly changing local and global economic landscape. Barriers exist in our traditional educational system, which has historically limited underrepresented groups' affiliation and membership in the disciplines of science and engineering. The recent incorporation of engineering into the latest science education reform efforts presents an opportunity to expose students as early as elementary school to engineering practices and habits of mind, which have the potential to stimulate creative thinking skills through engineering design. This qualitative study was designed to examine the ways in which engineering education has the potential to promote creativity and academic competence in elementary science classrooms. As a part of my study, a diverse group of students from two fifth-grade classrooms took part in a 10-12 hour, engineering-based curriculum unit (Engineering is Elementary) during their regular science instructional time. Using a sociocultural lens, to include cultural production and identities in practice as part of my framework, I analyzed group and individual performances through classroom observations, student interviews, and teacher reflections to better understand the meaning students made of their experiences with engineering. Findings from the study included the ways in which creativity was culturally produced in the classroom to include: 1) idea generation; 2) design and innovation; 3) gumption/resourcefulness; and 4) social value. Opportunities for collaboration increased through each stage of the unit culminating with the design challenge

Electronic manufacturing and packaging in Japan

Science.gov (United States)

Kelly, Michael J.; Boulton, William R. (Editor); Kukowski, John A.; Meieran, Eugene S.; Pecht, Michael; Peeples, John W.; Tummala, Rao R.

1995-01-01

This report summarizes the status of electronic manufacturing and packaging technology in Japan in comparison to that in the United States, and its impact on competition in electronic manufacturing in general. In addition to electronic manufacturing technologies, the report covers technology and manufacturing infrastructure, electronics manufacturing and assembly, quality assurance and reliability in the Japanese electronics industry, and successful product realization strategies. The panel found that Japan leads the United States in almost every electronics packaging technology. Japan clearly has achieved a strategic advantage in electronics production and process technologies. Panel members believe that Japanese competitors could be leading U.S. firms by as much as a decade in some electronics process technologies. Japan has established this marked competitive advantage in electronics as a consequence of developing low-cost, high-volume consumer products. Japan's infrastructure, and the remarkable cohesiveness of vision and purpose in government and industry, are key factors in the success of Japan's electronics industry. Although Japan will continue to dominate consumer electronics in the foreseeable future, opportunities exist for the United States and other industrial countries to capture an increasingly large part of the market. The JTEC panel has identified no insurmountable barriers that would prevent the United States from regaining a significant share of the consumer electronics market; in fact, there is ample evidence that the United States needs to aggressively pursue high-volume, low-cost electronic assembly, because it is a critical path leading to high-performance electronic systems.

System for cooling hybrid vehicle electronics, method for cooling hybrid vehicle electronics

Science.gov (United States)

France, David M.; Yu, Wenhua; Singh, Dileep; Zhao, Weihuan

2017-11-21

The invention provides a single radiator cooling system for use in hybrid electric vehicles, the system comprising a surface in thermal communication with electronics, and subcooled boiling fluid contacting the surface. The invention also provides a single radiator method for simultaneously cooling electronics and an internal combustion engine in a hybrid electric vehicle, the method comprising separating a coolant fluid into a first portion and a second portion; directing the first portion to the electronics and the second portion to the internal combustion engine for a time sufficient to maintain the temperature of the electronics at or below 175.degree. C.; combining the first and second portion to reestablish the coolant fluid; and treating the reestablished coolant fluid to the single radiator for a time sufficient to decrease the temperature of the reestablished coolant fluid to the temperature it had before separation.

Industrial chemistry engineering

International Nuclear Information System (INIS)

1993-01-01

This book on industrial chemistry engineering is divided in two parts. The first part deals with industrial chemistry, inorganic industrial chemistry, organic industrial chemistry, analytical chemistry and practical questions. The last parts explain the chemical industry, a unit parts and thermodynamics in chemical industry and reference. It reveals the test subjects for the industrial chemistry engineering with a written examination and practical skill.

UPS fellowships support creative engineering research

OpenAIRE

Crumbley, Liz

2007-01-01

A new $40,000 grant marks the 11th anniversary of support from the United Parcel Service (UPS) Foundation for doctoral fellowships in the Human Factors and Safety Engineering Graduate Program in the Grado Department of Industrial and Systems Engineering (ISE) in the College of Engineering.

Electronic ignition device for internal combustion engines. Elektronische Zuendvorrichtung fuer Brennkraftmaschinen

Energy Technology Data Exchange (ETDEWEB)

Erhard, W

1983-07-14

The purpose of the invention is to create an electronic ignition device for internal combustion engines, so that the exact setting of a required ignition timing can be done without troublesome balancing of the circuit and without temperature compensation processes. According to the invention, in order to solve this problem, the ignition device is characterized by an auxiliary circuit, with an auxiliary winding magnetically coupled to the ignition coil, a capacitor and a diode, which is connected in parallel with the control section of the control component. The auxiliary winding charges the capacitor up via the diode, as long as the induction and therefore the voltage in the auxiliary winding are increasing. After exceeding the maximum voltage, this is maintained at the capacitor while the voltage in the auxiliary winding decreases. If the difference reaches the threshold voltage of the control component, in particular of a thyristor, this is switched on and blocks the switching transistor. Due to this circuit, the ignition timing is very close behind the timing of the greatest possible energy input into the primary coil.

Mathematics for engineering

CERN Document Server

Bolton, W

2012-01-01

Mathematics for Engineering has been carefully designed to provide a maths course for a wide ability range, and does not go beyond the requirements of Advanced GNVQ. It is an ideal text for any pre-degree engineering course where students require revision of the basics and plenty of practice work. Bill Bolton introduces the key concepts through examples set firmly in engineering contexts, which students will find relevant and motivating. The second edition has been carefully matched to the Curriculum 2000 Advanced GNVQ units:

Problems in event based engine control

DEFF Research Database (Denmark)

Hendricks, Elbert; Jensen, Michael; Chevalier, Alain Marie Roger

1994-01-01

Physically a four cycle spark ignition engine operates on the basis of four engine processes or events: intake, compression, ignition (or expansion) and exhaust. These events each occupy approximately 180° of crank angle. In conventional engine controllers, it is an accepted practice to sample...... the engine variables synchronously with these events (or submultiples of them). Such engine controllers are often called event-based systems. Unfortunately the main system noise (or disturbance) is also synchronous with the engine events: the engine pumping fluctuations. Since many electronic engine...... problems on accurate air/fuel ratio control of a spark ignition (SI) engine....

A Requirement Engineering Framework for Electronic Data Sharing of Health Care Data Between Organizations

Science.gov (United States)

Liu, Xia; Peyton, Liam; Kuziemsky, Craig

Health care is increasingly provided to citizens by a network of collaboration that includes multiple providers and locations. Typically, that collaboration is on an ad-hoc basis via phone calls, faxes, and paper based documentation. Internet and wireless technologies provide an opportunity to improve this situation via electronic data sharing. These new technologies make possible new ways of working and collaboration but it can be difficult for health care organizations to understand how to use the new technologies while still ensuring that their policies and objectives are being met. It is also important to have a systematic approach to validate that e-health processes deliver the performance improvements that are expected. Using a case study of a palliative care patient receiving home care from a team of collaborating health organizations, we introduce a framework based on requirements engineering. Key concerns and objectives are identified and modeled (privacy, security, quality of care, and timeliness of service). And, then, proposed business processes which use new technologies are modeled in terms of these concerns and objectives to assess their impact and ensure that electronic data sharing is well regulated.

Influence of Climatic Factors on the Efficiency of Disposal Metal- Hydride Unit for the Double-Fuel Low-Speed Internal Combustion Engine of Gas Tankers

OpenAIRE

Cherednichenko, Oleksandr Costyntunovich; Tkach, Mykhaylo Romanovich

2017-01-01

Contemporary tendencies in the development of ship power engineering have been analyzed. Consideration was given to the specific features of the transportation of liquefied natural gas by gas tankers. The prospects of utilization of the secondary energy resources of marine double-fuel low-speed diesel engines were defined. The metal hydride units of a continuous action were offered for this purpose. The need for the estimation of the influence of climatic factors on the efficiency of disposal...

Can electronic search engines optimize screening of search results in systematic reviews: an empirical study.

Science.gov (United States)

Sampson, Margaret; Barrowman, Nicholas J; Moher, David; Clifford, Tammy J; Platt, Robert W; Morrison, Andra; Klassen, Terry P; Zhang, Li

2006-02-24

Most electronic search efforts directed at identifying primary studies for inclusion in systematic reviews rely on the optimal Boolean search features of search interfaces such as DIALOG and Ovid. Our objective is to test the ability of an Ultraseek search engine to rank MEDLINE records of the included studies of Cochrane reviews within the top half of all the records retrieved by the Boolean MEDLINE search used by the reviewers. Collections were created using the MEDLINE bibliographic records of included and excluded studies listed in the review and all records retrieved by the MEDLINE search. Records were converted to individual HTML files. Collections of records were indexed and searched through a statistical search engine, Ultraseek, using review-specific search terms. Our data sources, systematic reviews published in the Cochrane library, were included if they reported using at least one phase of the Cochrane Highly Sensitive Search Strategy (HSSS), provided citations for both included and excluded studies and conducted a meta-analysis using a binary outcome measure. Reviews were selected if they yielded between 1000-6000 records when the MEDLINE search strategy was replicated. Nine Cochrane reviews were included. Included studies within the Cochrane reviews were found within the first 500 retrieved studies more often than would be expected by chance. Across all reviews, recall of included studies into the top 500 was 0.70. There was no statistically significant difference in ranking when comparing included studies with just the subset of excluded studies listed as excluded in the published review. The relevance ranking provided by the search engine was better than expected by chance and shows promise for the preliminary evaluation of large results from Boolean searches. A statistical search engine does not appear to be able to make fine discriminations concerning the relevance of bibliographic records that have been pre-screened by systematic reviewers.

Electronic health records to support obesity-related patient care: Results from a survey of United States physicians.

Science.gov (United States)

Bronder, Kayla L; Dooyema, Carrie A; Onufrak, Stephen J; Foltz, Jennifer L

2015-08-01

Obesity-related electronic health record functions increase the rates of measuring Body Mass Index, diagnosing obesity, and providing obesity services. This study describes the prevalence of obesity-related electronic health record functions in clinical practice and analyzes characteristics associated with increased obesity-related electronic health record sophistication. Data were analyzed from DocStyles, a web-based panel survey administered to 1507 primary care providers practicing in the United States in June, 2013. Physicians were asked if their electronic health record has specific obesity-related functions. Logistical regression analyses identified characteristics associated with improved obesity-related electronic health record sophistication. Of the 88% of providers with an electronic health record, 83% of electronic health records calculate Body Mass Index, 52% calculate pediatric Body Mass Index percentile, and 32% flag patients with abnormal Body Mass Index values. Only 36% provide obesity-related decision support and 17% suggest additional resources for obesity-related care. Characteristics associated with having a more sophisticated electronic health record include age ≤45years old, being a pediatrician or family practitioner, and practicing in a larger, outpatient practice. Few electronic health records optimally supported physician's obesity-related clinical care. The low rates of obesity-related electronic health record functions currently in practice highlight areas to improve the clinical health information technology in primary care practice. More work can be done to develop, implement, and promote the effective utilization of obesity-related electronic health record functions to improve obesity treatment and prevention efforts. Published by Elsevier Inc.

Performance of an automated electronic acute lung injury screening system in intensive care unit patients.

Science.gov (United States)

Koenig, Helen C; Finkel, Barbara B; Khalsa, Satjeet S; Lanken, Paul N; Prasad, Meeta; Urbani, Richard; Fuchs, Barry D

2011-01-01

Lung protective ventilation reduces mortality in patients with acute lung injury, but underrecognition of acute lung injury has limited its use. We recently validated an automated electronic acute lung injury surveillance system in patients with major trauma in a single intensive care unit. In this study, we assessed the system's performance as a prospective acute lung injury screening tool in a diverse population of intensive care unit patients. Patients were screened prospectively for acute lung injury over 21 wks by the automated system and by an experienced research coordinator who manually screened subjects for enrollment in Acute Respiratory Distress Syndrome Clinical Trials Network (ARDSNet) trials. Performance of the automated system was assessed by comparing its results with the manual screening process. Discordant results were adjudicated blindly by two physician reviewers. In addition, a sensitivity analysis using a range of assumptions was conducted to better estimate the system's performance. The Hospital of the University of Pennsylvania, an academic medical center and ARDSNet center (1994-2006). Intubated patients in medical and surgical intensive care units. None. Of 1270 patients screened, 84 were identified with acute lung injury (incidence of 6.6%). The automated screening system had a sensitivity of 97.6% (95% confidence interval, 96.8-98.4%) and a specificity of 97.6% (95% confidence interval, 96.8-98.4%). The manual screening algorithm had a sensitivity of 57.1% (95% confidence interval, 54.5-59.8%) and a specificity of 99.7% (95% confidence interval, 99.4-100%). Sensitivity analysis demonstrated a range for sensitivity of 75.0-97.6% of the automated system under varying assumptions. Under all assumptions, the automated system demonstrated higher sensitivity than and comparable specificity to the manual screening method. An automated electronic system identified patients with acute lung injury with high sensitivity and specificity in diverse

A GPU OpenCL based cross-platform Monte Carlo dose calculation engine (goMC)

Science.gov (United States)

Tian, Zhen; Shi, Feng; Folkerts, Michael; Qin, Nan; Jiang, Steve B.; Jia, Xun

2015-09-01

Monte Carlo (MC) simulation has been recognized as the most accurate dose calculation method for radiotherapy. However, the extremely long computation time impedes its clinical application. Recently, a lot of effort has been made to realize fast MC dose calculation on graphic processing units (GPUs). However, most of the GPU-based MC dose engines have been developed under NVidia’s CUDA environment. This limits the code portability to other platforms, hindering the introduction of GPU-based MC simulations to clinical practice. The objective of this paper is to develop a GPU OpenCL based cross-platform MC dose engine named goMC with coupled photon-electron simulation for external photon and electron radiotherapy in the MeV energy range. Compared to our previously developed GPU-based MC code named gDPM (Jia et al 2012 Phys. Med. Biol. 57 7783-97), goMC has two major differences. First, it was developed under the OpenCL environment for high code portability and hence could be run not only on different GPU cards but also on CPU platforms. Second, we adopted the electron transport model used in EGSnrc MC package and PENELOPE’s random hinge method in our new dose engine, instead of the dose planning method employed in gDPM. Dose distributions were calculated for a 15 MeV electron beam and a 6 MV photon beam in a homogenous water phantom, a water-bone-lung-water slab phantom and a half-slab phantom. Satisfactory agreement between the two MC dose engines goMC and gDPM was observed in all cases. The average dose differences in the regions that received a dose higher than 10% of the maximum dose were 0.48-0.53% for the electron beam cases and 0.15-0.17% for the photon beam cases. In terms of efficiency, goMC was ~4-16% slower than gDPM when running on the same NVidia TITAN card for all the cases we tested, due to both the different electron transport models and the different development environments. The code portability of our new dose engine goMC was validated by

A GPU OpenCL based cross-platform Monte Carlo dose calculation engine (goMC).

Science.gov (United States)

Tian, Zhen; Shi, Feng; Folkerts, Michael; Qin, Nan; Jiang, Steve B; Jia, Xun

2015-10-07

Monte Carlo (MC) simulation has been recognized as the most accurate dose calculation method for radiotherapy. However, the extremely long computation time impedes its clinical application. Recently, a lot of effort has been made to realize fast MC dose calculation on graphic processing units (GPUs). However, most of the GPU-based MC dose engines have been developed under NVidia's CUDA environment. This limits the code portability to other platforms, hindering the introduction of GPU-based MC simulations to clinical practice. The objective of this paper is to develop a GPU OpenCL based cross-platform MC dose engine named goMC with coupled photon-electron simulation for external photon and electron radiotherapy in the MeV energy range. Compared to our previously developed GPU-based MC code named gDPM (Jia et al 2012 Phys. Med. Biol. 57 7783-97), goMC has two major differences. First, it was developed under the OpenCL environment for high code portability and hence could be run not only on different GPU cards but also on CPU platforms. Second, we adopted the electron transport model used in EGSnrc MC package and PENELOPE's random hinge method in our new dose engine, instead of the dose planning method employed in gDPM. Dose distributions were calculated for a 15 MeV electron beam and a 6 MV photon beam in a homogenous water phantom, a water-bone-lung-water slab phantom and a half-slab phantom. Satisfactory agreement between the two MC dose engines goMC and gDPM was observed in all cases. The average dose differences in the regions that received a dose higher than 10% of the maximum dose were 0.48-0.53% for the electron beam cases and 0.15-0.17% for the photon beam cases. In terms of efficiency, goMC was ~4-16% slower than gDPM when running on the same NVidia TITAN card for all the cases we tested, due to both the different electron transport models and the different development environments. The code portability of our new dose engine goMC was validated by

A GPU OpenCL based cross-platform Monte Carlo dose calculation engine (goMC)

International Nuclear Information System (INIS)

Tian, Zhen; Shi, Feng; Folkerts, Michael; Qin, Nan; Jiang, Steve B; Jia, Xun

2015-01-01

Monte Carlo (MC) simulation has been recognized as the most accurate dose calculation method for radiotherapy. However, the extremely long computation time impedes its clinical application. Recently, a lot of effort has been made to realize fast MC dose calculation on graphic processing units (GPUs). However, most of the GPU-based MC dose engines have been developed under NVidia’s CUDA environment. This limits the code portability to other platforms, hindering the introduction of GPU-based MC simulations to clinical practice. The objective of this paper is to develop a GPU OpenCL based cross-platform MC dose engine named goMC with coupled photon–electron simulation for external photon and electron radiotherapy in the MeV energy range. Compared to our previously developed GPU-based MC code named gDPM (Jia et al 2012 Phys. Med. Biol. 57 7783–97), goMC has two major differences. First, it was developed under the OpenCL environment for high code portability and hence could be run not only on different GPU cards but also on CPU platforms. Second, we adopted the electron transport model used in EGSnrc MC package and PENELOPE’s random hinge method in our new dose engine, instead of the dose planning method employed in gDPM. Dose distributions were calculated for a 15 MeV electron beam and a 6 MV photon beam in a homogenous water phantom, a water-bone-lung-water slab phantom and a half-slab phantom. Satisfactory agreement between the two MC dose engines goMC and gDPM was observed in all cases. The average dose differences in the regions that received a dose higher than 10% of the maximum dose were 0.48–0.53% for the electron beam cases and 0.15–0.17% for the photon beam cases. In terms of efficiency, goMC was ∼4–16% slower than gDPM when running on the same NVidia TITAN card for all the cases we tested, due to both the different electron transport models and the different development environments. The code portability of our new dose engine goMC was

Sustainable DTU, Electronics and It

DEFF Research Database (Denmark)

Schultz, Ole; Molin, Jesper; Hundebøll, Peder M.

2014-01-01

and suggest what should be done at the Campus to make it green and as the last part of it the prototype and suggest in detail what could be done. Over time there have been participating students from another elective course, Sustainable Electronics and IT as well students from Process and Innovation, Export...... Engineering and Civil Engineering students. The courses teach students that sustainability is a cross disciplinary topic – where engineering’s from different education has to cooperate for getting a proper solution. Electronic and IT Diplom engineering students are motivated learning about sustainability...... within their field when sustainability and environmental impact is seen in a context. That is done in an elective course: Sustainable Electronics and IT (SUSIE). We have integrated sustainability in the context of embedded wireless systems for building monitoring and control using the Internet of Things...

Practical electrical engineering

CERN Document Server

N Makarov, Sergey; Bitar, Stephen J

2016-01-01

This textbook provides comprehensive, in-depth coverage of the fundamental concepts of electrical and computer engineering. It is written from an engineering perspective, with special emphasis on circuit functionality and applications. Reliance on higher-level mathematics and physics, or theoretical proofs has been intentionally limited in order to prioritize the practical aspects of electrical engineering. This text is therefore suitable for a number of introductory circuit courses for other majors such as robotics, mechanical, biomedical, aerospace, civil, architecture, petroleum, and industrial engineering. The authors’ primary goal is to teach the aspiring engineering student all fundamental tools needed to understand, analyze and design a wide range of practical circuits and systems. Their secondary goal is to provide a comprehensive reference, for both major and non-major students as well as practicing engineers. Provides a self-contained, fundamental textbook on electric circuits and basic electronic...

The Effect of an Electronic SBAR Communication Tool on Documentation of Acute Events in the Pediatric Intensive Care Unit.

Science.gov (United States)

Panesar, Rahul S; Albert, Ben; Messina, Catherine; Parker, Margaret

2016-01-01

The Situation, Background, Assessment, Recommendation (SBAR) handoff tool is designed to improve communication. The effects of integrating an electronic medical record (EMR) with a SBAR template are unclear. The research team hypothesizes that an electronic SBAR template improves documentation and communication between nurses and physicians. In all, 84 patient events were recorded from 542 admissions to the pediatric intensive care unit. Three time periods were studied: (a) paper documentation only, (b) electronic documentation, and (c) electronic documentation with an SBAR template. Documentation quality was assessed using a 4-point scoring system. The frequency of event notes increased progressively during the 3 study periods. Mean quality scores improved significantly from paper documentation to EMR free-text notes and to electronic SBAR-template notes, as did nurse and attending physician notification. The implementation of an electronic SBAR note is associated with more complete documentation and increased frequency of documentation of communication among nurses and physicians. © The Author(s) 2014.

10 CFR 430.24 - Units to be tested.

Science.gov (United States)

2010-01-01

... this section, for each basic model 1 of conventional cooking tops, conventional ovens and microwave...-registered professional engineer who is not an employee of the manufacturer. The registered professional... consumption of the unit(s). The manufacturer is to keep the registered professional engineer's certifications...

Case-based Reasoning for Automotive Engine Performance Tune-up

International Nuclear Information System (INIS)

Vong, C. M.; Huang, H.; Wong, P. K.

2010-01-01

The automotive engine performance tune-up is greatly affected by the calibration of its electronic control unit (ECU). The ECU calibration is traditionally done by trial-and-error method. This traditional method consumes a large amount of time and money because of a large number of dynamometer tests. To resolve this problem, case based reasoning (CBR) is employed, so that an existing and effective ECU setup can be adapted to fit another similar class of engines. The adaptation procedure is done through a more sophisticated step called case-based adaptation (CBA)[1, 2]. CBA is an effective knowledge management tool, which can interactively learn the expert adaptation knowledge. The paper briefly reviews the methodologies of CBR and CBA. Then the application to ECU calibration is described via a case study. With CBR and CBA, the efficiency of calibrating an ECU can be enhanced. A prototype system has also been developed to verify the usefulness of CBR in ECU calibration.

Progress in increasing electronic reporting of laboratory results to public health agencies--United States, 2013.

Science.gov (United States)

2013-09-27

Electronic reporting of laboratory results to public health agencies can improve public health surveillance for reportable diseases and conditions by making reporting more timely and complete. Since 2010, CDC has provided funding to 57 state, local, and territorial health departments through the Epidemiology and Laboratory Capacity for Infectious Diseases cooperative agreement to assist with improving electronic laboratory reporting (ELR) from clinical and public health laboratories to public health agencies. As part of this agreement, CDC and state and large local health departments are collaborating to monitor ELR implementation in the United States by developing data from each jurisdiction regarding total reporting laboratories, laboratories sending ELR by disease category and message format, and the number of ELR laboratory reports compared with the total number of laboratory reports. At the end of July 2013, 54 of the 57 jurisdictions were receiving at least some laboratory reports through ELR, and approximately 62% of 20 million laboratory reports were being received electronically, compared with 54% in 2012. Continued progress will require collaboration between clinical laboratories, laboratory information management system (LIMS) vendors, and public health agencies.

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XX, CUMMINS DIESEL ENGINE, MAINTENANCE SUMMARY.

Science.gov (United States)

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO PROVIDE A SUMMARY OF THE REASONS AND PROCEDURES FOR DIESEL ENGINE MAINTENANCE. TOPICS ARE WHAT ENGINE BREAK-IN MEANS, ENGINE BREAK-IN, TORQUING BEARINGS (TEMPLATE METHOD), AND THE NEED FOR MAINTENANCE. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING FILM "CUMMINS DIESEL ENGINE…

Analysis and optimization with ecological objective function of irreversible single resonance energy selective electron heat engines

International Nuclear Information System (INIS)

Zhou, Junle; Chen, Lingen; Ding, Zemin; Sun, Fengrui

2016-01-01

Ecological performance of a single resonance ESE heat engine with heat leakage is conducted by applying finite time thermodynamics. By introducing Nielsen function and numerical calculations, expressions about power output, efficiency, entropy generation rate and ecological objective function are derived; relationships between ecological objective function and power output, between ecological objective function and efficiency as well as between power output and efficiency are demonstrated; influences of system parameters of heat leakage, boundary energy and resonance width on the optimal performances are investigated in detail; a specific range of boundary energy is given as a compromise to make ESE heat engine system work at optimal operation regions. Comparing performance characteristics with different optimization objective functions, the significance of selecting ecological objective function as the design objective is clarified specifically: when changing the design objective from maximum power output into maximum ecological objective function, the improvement of efficiency is 4.56%, while the power output drop is only 2.68%; when changing the design objective from maximum efficiency to maximum ecological objective function, the improvement of power output is 229.13%, and the efficiency drop is only 13.53%. - Highlights: • An irreversible single resonance energy selective electron heat engine is studied. • Heat leakage between two reservoirs is considered. • Power output, efficiency and ecological objective function are derived. • Optimal performance comparison for three objective functions is carried out.

Collaboration in nuclear engineering education between France and the United States: Participation of French students at Texas A ampersand M University

International Nuclear Information System (INIS)

Peddicord, K.L.; Durand, J.L.; Gousty, Y.; Jeneveau, A.; Erdman, C.A.

1988-01-01

Universities in the United States have had a long tradition of accepting students from other countries to pursue graduate degrees. This has particularly been the case in the fields of engineering and science. This trend has grown to the point that in several graduate engineering fields, the percentage of foreign nationals outnumbers US enrollees. Historically, most foreign students studying in the US universities have been from developing countries. Usually these students apply and are accepted on a case-by-case basis. For a number of reasons, less emphasis has been placed on programs with western Europe. In this paper, a program of collaboration is described in which the Department of Nuclear Engineering at Texas A ampersand M University has entered into memoranda of agreement with two institutions in France. The two universities are the Institut National Polytechnique de Grenoble (INPG) in Grenoble and the Ecole Polytechnique Feminine (EPF) in Sceaux. The purpose of the program is to enable students in nuclear engineering to simultaneously complete requirements for the diploma and the MS degree

Distributed Control Architecture for Gas Turbine Engine. Chapter 4

Science.gov (United States)

Culley, Dennis; Garg, Sanjay

2009-01-01

The transformation of engine control systems from centralized to distributed architecture is both necessary and enabling for future aeropropulsion applications. The continued growth of adaptive control applications and the trend to smaller, light weight cores is a counter influence on the weight and volume of control system hardware. A distributed engine control system using high temperature electronics and open systems communications will reverse the growing trend of control system weight ratio to total engine weight and also be a major factor in decreasing overall cost of ownership for aeropropulsion systems. The implementation of distributed engine control is not without significant challenges. There are the needs for high temperature electronics, development of simple, robust communications, and power supply for the on-board electronics.

Engineering Mixed Ionic Electronic Conduction in La 0.8 Sr 0.2 MnO 3+ δ Nanostructures through Fast Grain Boundary Oxygen Diffusivity

KAUST Repository

Saranya, Aruppukottai M.

2015-04-09

© 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim. Nanoionics has become an increasingly promising field for the future development of advanced energy conversion and storage devices, such as batteries, fuel cells, and supercapacitors. Particularly, nanostructured materials offer unique properties or combinations of properties as electrodes and electrolytes in a range of energy devices. However, the enhancement of the mass transport properties at the nanoscale has often been found to be difficult to implement in nanostructures. Here, an artificial mixed ionic electronic conducting oxide is fabricated by grain boundary (GB) engineering thin films of La0.8Sr0.2MnO3+δ. This electronic conductor is converted into a good mixed ionic electronic conductor by synthesizing a nanostructure with high density of vertically aligned GBs with high concentration of strain-induced defects. Since this type of GBs present a remarkable enhancement of their oxide-ion mass transport properties (of up to six orders of magnitude at 773 K), it is possible to tailor the electrical nature of the whole material by nanoengineering, especially at low temperatures. The presented results lead to fundamental insights into oxygen diffusion along GBs and to the application of these engineered nanomaterials in new advanced solid state ionics devices such are micro-solid oxide fuel cells or resistive switching memories. An electronic conductor such as La0.8Sr0.2MnO3+δ is converted into a good mixed ionic electronic conductor by synthesizing a nanostructure with excellent electronic and oxygen mass transport properties. Oxygen diffusion highways are created by promoting a high concentration of strain-induced defects in the grain boundary region. This novel strategy opens the way for synthesizing new families of artificial mixed ionic-electronic conductors by design.

Problems of development and putting into education process an electronic textbook on special discipline 'General theory and construction of heat-and-power engineering facilities'

International Nuclear Information System (INIS)

Karitskaya, S.G.; Ruzanov, K.A.; Davletov, V.S.

2005-01-01

The results of work of making the electronic textbook of special discipline ('General theory and construction of heat-and-power engineering facilities' are brought. The principles and requirements, presented towards literature of such type, are outlined. (author)

Career Directions--Electronics Technician

Science.gov (United States)

Tech Directions, 2012

2012-01-01

Electronics technicians (ETs) work with electronics engineers to set up and maintain complicated electronics equipment that many of today's businesses rely on. The field is varied. An ET might service the industrial controls on a factory floor. Or repair missile control systems for the government. Or an ET could specialize in cars and trucks,…

Preferences of Current and Potential Patients and Family Members Regarding Implementation of Electronic Communication Portals in Intensive Care Units.

Science.gov (United States)

Brown, Samuel M; Bell, Sigall K; Roche, Stephanie D; Dente, Erica; Mueller, Ariel; Kim, Tae-Eun; O'Reilly, Kristin; Lee, Barbara Sarnoff; Sands, Ken; Talmor, Daniel

2016-03-01

The quality of communication with patients and family members in intensive care units (ICUs) is a focus of current interest for clinical care improvement. Electronic communication portals are commonly used in other healthcare settings to improve communication. We do not know whether patients and family members desire such portals in ICUs, and if so, what functionality they should provide. To define interest in and desired elements of an electronic communication portal among current and potential ICU patients and their family members. We surveyed, via an Internet panel, 1,050 English-speaking adults residing in the United States with a personal or family history of an ICU admission within 10 years (cohort A) and 1,050 individuals without a history of such admission (cohort B). We also administered a survey instrument in person to 105 family members of patients currently admitted to ICUs at an academic medical center in Boston (cohort C). Respondents, especially current ICU family members, supported an electronic communication portal, including access via an electronic tablet. They wanted at least daily updates, one-paragraph summaries of family meetings including a list of key decisions made, and knowledge of the role and experience of treating clinicians. Overall, they preferred detailed rather than "big picture" information. Respondents were generally comfortable sharing information with their family members. Preferences regarding a communication portal varied significantly by age, sex, ethnicity, and prior experience with ICU hospitalization. Electronic communication portals appear welcome in contemporary ICUs. Frequent updates, knowledge about the professional qualifications of clinicians, detailed medical information, and documentation of family meetings are particularly desired.

Wood products used in constructing conservation and development projects by the Corps of Engineers in the United States, 1962 and 1978

Science.gov (United States)

W. H. Reid; D. B. McKeever

Estimates of the amounts of wood products used in constructing civil conservation and development projects by the Corps of Engineers in the United States are presented for the years 1962 and 1978. Amounts of lumber, laminated lumber, poles and piling, and plywood used in construction are stratified by five construction categories, and three types of uses. Estimates of...

Performance of a hybrid hydrogen–gasoline engine under various operating conditions

International Nuclear Information System (INIS)

Ji, Changwei; Wang, Shuofeng; Zhang, Bo

2012-01-01

Highlights: ► We develop a combustion strategy for the hybrid hydrogen–gasoline engine (HHGE). ► The HHGE produced much lower HC and CO emissions at cold start. ► The H 2 -gasoline blends were effective for improving engine performance at idle and part loads. ► The HHGE could run smoothly at lean conditions. -- Abstract: This paper proposed a new combustion strategy for the spark-ignited (SI) engines. A gasoline engine was converted into a hybrid hydrogen–gasoline engine (HHGE) by adding a hydrogen injection system and a hybrid electronic control unit. Different from the conventional gasoline and hydrogen–enriched gasoline engines, the HHGE is fueled with the pure hydrogen at cold start to produce almost zero emissions, with the hydrogen–gasoline blends at idle and part loads to further improve thermal efficiency and reduce emissions, and with the pure gasoline to ensure the engine power output at high loads. Because the HHGE is fueled with the pure gasoline at high loads and speeds, experiments are only conducted at clod start, idle and part load conditions. Since lean combustion avails the further improvement of the engine performance, the HHGE was fueled with the lean mixtures in all tests. The experimental results showed that the hybrid hydrogen–gasoline engine was started successfully with the pure hydrogen, which produced 94.7% and 99.5% reductions in HC and CO emissions within 100 s from the onset of the cold start, compared with the original gasoline engine. At an excess air ratio of 1.37 and idle conditions, indicated thermal efficiency of the 3% hydrogen–blended gasoline engine was 46.3% higher than that of the original engine. Moreover, the engine cyclic variation was eased, combustion duration was shortened and HC, CO and NOx emissions were effectively reduced for the hybrid hydrogen–gasoline engines.

Report on survey in fiscal 2000. Survey on introduction of external accreditation system in engineer education (electronic information communications); 2000 nendo chosa hokokusho. Gijutsusha kyoiku no gaibu ninteiseido donyu ni kansuru chosa (Denshi joho tsushin)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to ensure international applicability of engineer education such as in universities and other organizations, and to improve the environment to supply human resources demanded by economic societies, surveys were performed on the external accreditation system for engineer education such as in universities and other organizations. In the field of electronic information communications, a committee to correspond to JABEE was established to perform system build-up, where the discussions were advanced. This field was classified into the following four specified areas: general aspect of electric/electronic/information communication engineering, electronics, information communications, and information systems. A supplementary explanation was given on the educational contents except for the information systems, based on which the self-assessment criteria and the evaluation table (for trial use) were prepared. For the examiner training, instructors were invited from ABET in the U.S.A., and training meetings were held. In addition, two committee members were sent as observers to the examinations being carried out at ABET. The trial experiments were conducted for the information communications program at the engineering department of Niigata University, and the electronic system engineering class at Sendai Radio Wave Industrial College. This paper summarizes the results of the examinations. (NEDO)

Progress along developmental tracks for electronic health records implementation in the United States

Directory of Open Access Journals (Sweden)

Hollar David W

2009-03-01

Full Text Available Abstract The development and implementation of electronic health records (EHR have occurred slowly in the United States. To date, these approaches have, for the most part, followed four developmental tracks: (a Enhancement of immunization registries and linkage with other health records to produce Child Health Profiles (CHP, (b Regional Health Information Organization (RHIO demonstration projects to link together patient medical records, (c Insurance company projects linked to ICD-9 codes and patient records for cost-benefit assessments, and (d Consortia of EHR developers collaborating to model systems requirements and standards for data linkage. Until recently, these separate efforts have been conducted in the very silos that they had intended to eliminate, and there is still considerable debate concerning health professionals access to as well as commitment to using EHR if these systems are provided. This paper will describe these four developmental tracks, patient rights and the legal environment for EHR, international comparisons, and future projections for EHR expansion across health networks in the United States.

Electronic cigarette initiation among minority youth in the United States.

Science.gov (United States)

Hammig, Bart; Daniel-Dobbs, Page; Blunt-Vinti, Heather

2017-05-01

Electronic cigarettes (e-cigarette) use among youth is a pressing public health issue, with prevalence of use surpassing that of tobacco cigarettes. While research concerning e-cigarettes has proliferated in recent years, there is a dearth of information regarding those whose first exposure to tobacco products was an e-cigarette. To examine factors associated with e-cigarette initiation among minority youth in the United States. Data on minority students in middle and high schools in the United States derived from the 2014 National Youth Tobacco Survey (NYTS) were sampled (weighted N = 27,294,454). We examined e-cigarette initiation among minority youth using logistic regression models to identify related factors. In 2014, 736,158 minority youth were e-cigarette initiators. Odds of e-cigarette initiation was highest among Hispanic youth [adjusted odds ratio (AOR) = 2.70; 95% confidence interval (CI) = 1.60-4.56]. Exposure to e-cigarette advertising (AOR = 1.64; 95% CI = 1.07-2.50), perceptions of little to no harm (AOR = 7.08; 95% CI = 4.03-12.46), and believing e-cigarettes were less addictive than tobacco (AOR = 2.15; 95% CI = 1.52-3.02) were associated with e-cigarette initiation. Odds of initiating e-cigarette use was highest among Hispanic youth. Among minority youth, e-cigarette initiation was associated with perceptions of harm and addiction potential, as well as exposure to e-cigarette advertising. Therefore, prevention efforts targeting minority youth who are at risk of becoming e-cigarette initiators may benefit by incorporating these factors into prevention campaigns.

A multi-purpose unit concept to integrate storage, transportation, and the engineered barrier system

International Nuclear Information System (INIS)

Hollaway, W.R.; Rozier, R.; Nitti, D.A.; Williams, J.R.

1993-01-01

The Multi-Purpose Unit (MPU) is a new concept for standardizing and integrating the waste management functions of spent fuel storage, transportation, and geologic disposal. The MPU concept would use one unit, composed of a relatively thick-walled inner canister with a multi-purpose overpack, to meet the requirements for storage in 10 CFR 72, transportation in 10 CFR 71, and the engineered barrier system in 10 CFR 60. The MPU concept differs from the recently proposed Multi-Purpose Canister (MPC) concept in that the MPU concept uses a single multi-purpose overpack for storage, transportation, and geologic disposal, while the MPC concept uses separate and unique overpacks for each of these system functions. A design concept for the MPU is presented along with an estimate of unit costs. An initial evaluation of overall system cost showed that the MPU concept could be economically competitive with the current reference system. The MPU concept provides the potential for significant reduction, simplification, and standardization of Civilian Radioactive Waste Management (CRWMS) facilities and operations, including those at the utilities, during waste acceptance and transportation, and at the Monitored Retrievable Storage (MRS) facility and the repository. The primary issues for the MPU concept relate to uncertainties with respect to licensing, and the programmatic risks associated with implementing the MPU concept before the repository design is finalized. The strong potential exhibited by the MPU concept demonstrates that this option merits additional development and should be considered in the next phase of work on multi-purpose concepts for the CRWMS

5th International Conference on Electronics, Communications and Networks

CERN Document Server

2016-01-01

This book comprises peer-reviewed contributions presented at the 5th International Conference on Electronics, Communications and Networks (CECNet 2015), held in Shanghai, China, 12-15 December, 2015. It includes new multi-disciplinary topics spanning a unique depth and breadth of cutting-edge research areas in Electronic Engineering, Communications and Networks, and Computer Technology. More generally, it is of interest to academics, students and professionals involved in Consumer Electronics Technology, Communication Engineering and Technology, Wireless Communication Systems and Technology, and Computer Engineering and Technology.

Japan's electronic packaging technologies

Science.gov (United States)

Tummala, Rao R.; Pecht, Michael

1995-02-01

The JTEC panel found Japan to have significant leadership over the United States in the strategic area of electronic packaging. Many technologies and products once considered the 'heart and soul' of U.S. industry have been lost over the past decades to Japan and other Asian countries. The loss of consumer electronics technologies and products is the most notable of these losses, because electronics is the United States' largest employment sector and is critical for growth businesses in consumer products, computers, automobiles, aerospace, and telecommunications. In the past there was a distinction between consumer and industrial product technologies. While Japan concentrated on the consumer market, the United States dominated the industrial sector. No such distinction is anticipated in the future; the consumer-oriented technologies Japan has dominated are expected to characterize both domains. The future of U.S. competitiveness will, therefore, depend on the ability of the United States to rebuild its technological capabilities in the area of portable electronic packaging.

Electronic theodolite intersection systems

OpenAIRE

Bingley, R. M.

1990-01-01

The development of electronic surveying instruments, such as electronic theodolites, and concurrent advances in computer technology, has revolutionised engineering surveying; one of the more recent examples being the introduction of Electronic Theodolite Intersection Systems (ETISs). An ETIS consists of two or more electronic theodolites and a computer, with peripheral hardware and suitable software. The theoretical principles on which they are based have been known for a long time, but ...

Tracking search engine queries for suicide in the United Kingdom, 2004-2013.

Science.gov (United States)

Arora, V S; Stuckler, D; McKee, M

2016-08-01

First, to determine if a cyclical trend is observed for search activity of suicide and three common suicide risk factors in the United Kingdom: depression, unemployment, and marital strain. Second, to test the validity of suicide search data as a potential marker of suicide risk by evaluating whether web searches for suicide associate with suicide rates among those of different ages and genders in the United Kingdom. Cross-sectional. Search engine data was obtained from Google Trends, a publicly available repository of information of trends and patterns of user searches on Google. The following phrases were entered into Google Trends to analyse relative search volume for suicide, depression, job loss, and divorce, respectively: 'suicide'; 'depression + depressed + hopeless'; 'unemployed + lost job'; 'divorce'. Spearman's rank correlation coefficient was employed to test bivariate associations between suicide search activity and official suicide rates from the Office of National Statistics (ONS). Cyclical trends were observed in search activity for suicide and depression-related search activity, with peaks in autumn and winter months, and a trough in summer months. A positive, non-significant association was found between suicide-related search activity and suicide rates in the general working-age population (15-64 years) (ρ = 0.164; P = 0.652). This association is stronger in younger age groups, particularly for those 25-34 years of age (ρ = 0.848; P = 0.002). We give credence to a link between search activity for suicide and suicide rates in the United Kingdom from 2004 to 2013 for high risk sub-populations (i.e. male youth and young professionals). There remains a need for further research on how Google Trends can be used in other areas of disease surveillance and for work to provide greater geographical precision, as well as research on ways of mitigating the risk of internet use leading to suicide ideation in youth. Copyright © 2015 The Royal

Disciplinary Literacies in an Engineering Club: Exploring Productive Communication and the Engineering Design Process

Science.gov (United States)

Shanahan, Lynn E.; McVee, Mary B.; Slivestri, Katarina N.; Haq, Kate

2016-01-01

This conceptual article addresses the question: What are the disciplinary literacy practices surrounding the Engineering Design Process (EDP) at the elementary level? Recent attention has focused on developing science, technology, engineering, and math (STEM) skills for U.S. students. In the United States, the Next Generation Science Standards and…

Electronic-Reconstruction-Enhanced Tunneling Conductance at Terrace Edges of Ultrathin Oxide Films.

Science.gov (United States)

Wang, Lingfei; Kim, Rokyeon; Kim, Yoonkoo; Kim, Choong H; Hwang, Sangwoon; Cho, Myung Rae; Shin, Yeong Jae; Das, Saikat; Kim, Jeong Rae; Kalinin, Sergei V; Kim, Miyoung; Yang, Sang Mo; Noh, Tae Won

2017-11-01

Quantum mechanical tunneling of electrons across ultrathin insulating oxide barriers has been studied extensively for decades due to its great potential in electronic-device applications. In the few-nanometers-thick epitaxial oxide films, atomic-scale structural imperfections, such as the ubiquitously existed one-unit-cell-high terrace edges, can dramatically affect the tunneling probability and device performance. However, the underlying physics has not been investigated adequately. Here, taking ultrathin BaTiO 3 films as a model system, an intrinsic tunneling-conductance enhancement is reported near the terrace edges. Scanning-probe-microscopy results demonstrate the existence of highly conductive regions (tens of nanometers wide) near the terrace edges. First-principles calculations suggest that the terrace-edge geometry can trigger an electronic reconstruction, which reduces the effective tunneling barrier width locally. Furthermore, such tunneling-conductance enhancement can be discovered in other transition metal oxides and controlled by surface-termination engineering. The controllable electronic reconstruction can facilitate the implementation of oxide electronic devices and discovery of exotic low-dimensional quantum phases. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Engineer: The Professional Bulletin of Army Engineers, Jan-Apr 2010

Science.gov (United States)

2010-04-01

Dornstadter 51 Transformation in Korea By Major Rafael Pazos and Captain Miguel Uc Headquarters, Department of the ArmyVolume 40 PB 5-10-1...States with an By Major Rafael Pazos and Captain Miguel Uc January-April 201052 Engineer initial grant of 205 acres at USAG–Humphreys, allowing the...the quality of life of our Service members. Major Pazos is the deputy commander of the United States Army Corps of Engineers (USACE), Gulf Region

Alternative Pathways to Engineering Success--Using Academic and Social Integration to Understand Two-Year Engineering Student Success

Science.gov (United States)

Marra, Rose M.; Tsai, Chia-Lin; Bogue, Barbara; Pytel, Jean Landa

2015-01-01

The need for educating engineers in the United States continues as the projected demand is rising the number of high school seniors planning to enter engineering careers has remained relatively stable (Sargent, 2014). Additionally, figures show that attrition rates in undergraduate engineering continue to be an area of concern, (Sargent, 2014;…

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XIX, I--ENGINE TUNE-UP--CUMMINS DIESEL ENGINE, II--FRONT END SUSPENSION AND AXLES.

Science.gov (United States)

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF DIESEL ENGINE TUNE-UP PROCEDURES AND THE DESIGN OF FRONT END SUSPENSION AND AXLES USED ON DIESEL ENGINE EQUIPMENT. TOPICS ARE (1) PRE-TUNE-UP CHECKS, (2) TIMING THE ENGINE, (3) INJECTOR PLUNGER AND VALVE ADJUSTMENTS, (4) FUEL PUMP ADJUSTMENTS ON THE ENGINE (PTR AND PTG),…

SmartUnit: Empirical Evaluations for Automated Unit Testing of Embedded Software in Industry

OpenAIRE

Zhang, Chengyu; Yan, Yichen; Zhou, Hanru; Yao, Yinbo; Wu, Ke; Su, Ting; Miao, Weikai; Pu, Geguang

2018-01-01

In this paper, we aim at the automated unit coverage-based testing for embedded software. To achieve the goal, by analyzing the industrial requirements and our previous work on automated unit testing tool CAUT, we rebuild a new tool, SmartUnit, to solve the engineering requirements that take place in our partner companies. SmartUnit is a dynamic symbolic execution implementation, which supports statement, branch, boundary value and MC/DC coverage. SmartUnit has been used to test more than one...

THE DESIGNING OF ELECTRONIC TEACHING-METHODS COMPLEX «GRAPHICS» FOR REALIZATION OF COMPUTER-BASED LEARNING OF ENGINEERING-GRAPHIC DISCIPLINES

Directory of Open Access Journals (Sweden)

Іван Нищак

2015-12-01

Full Text Available The article contains Theoretical Foundations of designing of author’s electronic educational-methodical complex (EEMC «Graphics», intended to implement the engineering-graphic preparation of future teachers of technology in terms of computer-based learning. The process of designing of electronic educational-methodical complex “Graphics” includes the following successive stages: 1 identification of didactic goals and objectives; 2the designing of patterns of EEMC; 3 the selection of contents and systematization of educational material; 4 the program-technical implementation of EEMC; 5 interface design; 6 expert assessment of quality of EEMC; 7 testing of EEMC; 8 adjusting the software; 9 the development of guidelines and instructions for the use of EEMC.

IEEE Milestone at CERN - W Cleon Anderson (right), president of the Institute of Electrical and Electronics Engineers, unveils the Milestone plaque at CERN, together with Georges Charpak

CERN Multimedia

Maximilien Brice

2005-01-01

At a ceremony on 26 September at CERN, W Cleon Anderson, president of the Institute of Electrical and Electronics Engineers (IEEE), formally dedicated a "Milestone" plaque in recognition of the invention of electronic particle detectors at CERN. The plaque was unveiled by Anderson and Georges Charpak, the Nobel-prize winning inventor of wire-chamber technology at CERN.

Review on the application of system engineer model in nuclear power plant

International Nuclear Information System (INIS)

Chen Guocai

2005-01-01

system engineer was adopted deeply and play important roles in nuclear power plants in United States and Canada, the plant performance indicates that system engineer mode is a good practice. Qinshan CANDU nuclear power plant, established the system engineer mode since commissioning, as a core, system engineer took charge of the preparation of commissioning procedures, organization, coordination and guidance of commissioning execution. Unit 1 was put into commercial operation 43 days in advance and 112 days ahead of schedule for Unit 2 with excellent quality. Commissioning period are just 10.5 and 7.8 months for both Units respectively. Which is the shortest record in the history of CANDU nuclear power plant commissioning up to now. During operation, systems engineer has strength in routine operating and units reliability improvement. Based on the practice of Qinshan CANDU nuclear power plant commissioning and production technical management, the main form of the article in the era of knowledge: its characteristics and advantage and operating mode of the system engineer mode. System engineer is different from project engineer, he act as the master of systems and takes full responsibility for systems technical management. System engineer should do many jobs and improvement schedule to ensure his system in health status. System health monitor is a basic tool in system management, which is useful for equipment performance improvement. At last, the author made a forecast and comment on the prospects for the system engineer in the future. (author)

Hamsters, Picture Books, and Engineering Design

Science.gov (United States)

Tank, Kristina; Pettis, Christy; Moore, Tamara; Fehr, Abby

2013-01-01

With the integration of engineering into science instruction, teachers have been seeking ways to add engineering in their classrooms. This article presents a primary (K-2) STEM unit that took place in a half-day kindergarten classroom as a way to address the scientific and engineering practices (dimension 1, p.41) and the disciplinary core idea…

Separated core turbofan engine; Core bunrigata turbofan engine

Energy Technology Data Exchange (ETDEWEB)

Saito, Y; Endo, M; Matsuda, Y; Sugiyama, N; Sugahara, N; Yamamoto, K [National Aerospace Laboratory, Tokyo (Japan)

1996-04-01

This report outlines the separated core turbofan engine. This engine is featured by parallel separated arrangement of a fan and core engine which are integrated into one unit in the conventional turbofan engine. In general, cruising efficiency improvement and noise reduction are achieved by low fan pressure ratio and low exhaust speed due to high bypass ratio, however, it causes various problems such as large fan and nacelle weight due to large air flow rate of a fan, and shift of an operating point affected by flight speed. The parallel separated arrangement is thus adopted. The stable operation of a fan and core engine is easily retained by independently operating air inlet unaffected by fan. The large degree of freedom of combustion control is also obtained by independent combustor. Fast response, simple structure and optimum aerodynamic design are easily achieved. This arrangement is also featured by flexibility of development and easy maintenance, and by various merits superior to conventional turbofan engines. It has no technological problems difficult to be overcome, and is also suitable for high-speed VTOL transport aircraft. 4 refs., 5 figs.

ELEC-2002: Electronics in HEP

CERN Multimedia

Technical Training; Tel. 74924

2001-01-01

ELEC-2002 is a 15-session modern electronic course, given by CERN physicists and engineers, in a new format within the framework of the Technical Training Programme. This course is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2002 will composed of two terms: sessions will take place on Tuesdays and Thursdays, from 14h00 to 16h30, in the Training Centre Auditorium, bldg. 593.   Winter term: Readout and system electronics for physics (January-February 2002) Introduction: the basics of electronics. Review of electrical circuits: Laplace transforms, transfer functions, RC-CR networks. Transistors, operational amplifiers and applications, transmission lines. (Philippe Farthouat, 15 January) Analogue signal processing. Preamplifiers and shapers; noise in ele...

Preparative engineering on the Tomari Nuclear Power Station Unit 3. In-site measurement on wave pressure working to new type bank protection

International Nuclear Information System (INIS)

Matsumoto, Yoriaki; Hoshi, Hideki; Amano, Hideki

2003-01-01

The Tomari Nuclear Power Station Unit 3 is planned to construct it at sea-side area adjacent to southern-east portion of Unit 1 and 2, and has been carried out its preparative engineerings such as bank protection with about 670 m in length, its development, and so on, corresponding to it. Among them, as type of landfill for protection of important construction at its background the Amahata covered-block type bank protection developed by a series of hydrologic tests was adopted. This engineering was begun on March, 2001, and most of establishment on the landfill bank protection was finished on June, 2003. Then, an in-situ measurement aiming to obtain actual testing data and so on of wave pressure at this type of bank protection, was planned, to carry out its measurement at winter (October, 2002 to February, 2003) showing the highest wave at this sea area. Here were reported on relationship between incident wave and wave pressure feature working at new type bank protection together with describing on outlines of the in-situ measurement. (G.K.)

Emerging Trends in Computing, Informatics, Systems Sciences, and Engineering

CERN Document Server

Elleithy, Khaled

2013-01-01

Emerging Trends in Computing, Informatics, Systems Sciences, and Engineering includes a set of rigorously reviewed world-class manuscripts addressing and detailing state-of-the-art research projects in the areas of  Industrial Electronics, Technology & Automation, Telecommunications and Networking, Systems, Computing Sciences and Software Engineering, Engineering Education, Instructional Technology, Assessment, and E-learning. This book includes the proceedings of the International Joint Conferences on Computer, Information, and Systems Sciences, and Engineering (CISSE 2010). The proceedings are a set of rigorously reviewed world-class manuscripts presenting the state of international practice in Innovative Algorithms and Techniques in Automation, Industrial Electronics and Telecommunications.

ETRAN 1999: Society for Electronics,Telecommunications, Computers, Automation and Nuclear Engineering. Section for Nuclear Techniques and Technology. Proceedings of the XLIII Conference. Vol IV

International Nuclear Information System (INIS)

Spasojevic, D.; Smiljanic, M.; Bozic, D.; Stankovic, D.

1999-01-01

The XLIII ETRAN Conference of the Society for Electronic, Telecommunications, Computers, Automation and Nuclear Engineering was held on 20-22 Sep, 1999. In the Proceedings of the Conference The Commission of the Nuclear Technique and Technology has 19 papers presented in three sessions.

Women in Engineering: Insight into Why Some Engineering Departments Have More Success in Recruiting and Graduating Women

Science.gov (United States)

Bossart, Jean; Bharti, Neelam

2017-01-01

Universities across the United States (U.S.) are perplexed as to why fewer women than men study engineering and why even fewer complete the curriculum and earn an undergraduate degree in engineering. The percentage of undergraduate engineering degrees awarded annually to women in the U.S. since 2000 has remained relatively constant at around 20%.…

Mechanical engineers' handbook, design, instrumentation, and controls

CERN Document Server

Kutz, Myer

2015-01-01

Full coverage of electronics, MEMS, and instrumentation andcontrol in mechanical engineering This second volume of Mechanical Engineers' Handbookcovers electronics, MEMS, and instrumentation and control, givingyou accessible and in-depth access to the topics you'll encounterin the discipline: computer-aided design, product design formanufacturing and assembly, design optimization, total qualitymanagement in mechanical system design, reliability in themechanical design process for sustainability, life-cycle design,design for remanufacturing processes, signal processing, dataacquisition and dis

Engineering Encounters: Elephant Trunks and Dolphin Tails

Science.gov (United States)

Hefty, Lukas

2014-01-01

This article describes how one class at Douglas Jamerson Elementary School in St. Petersburg, Florida, a center for engineering and mathematics, incorporated an Engineering Design Process into its curriculum. At Jamerson Elementary, all students in kindergarten through fifth grade engage in teacher-created, integrated engineering units of study,…

Recent developments in the United Kingdom in ion implantation equipment for engineering components

International Nuclear Information System (INIS)

Gardner, P.R.

1988-01-01

Harwell has been particularly active in the development and commercial exploitation of low-cost, rugged, reliable and simple-to-operate equipment for implantation of engineering components with gaseous ions, especially nitrogen. Laboratory experiments show this to reduce mild abrasive wear in a wide range of materials by factors typically 2-10, provided operating temperatures remain below about 400 deg C. The latest nitrogen ion implantation machine (the Tecvac 221 model) embodies a substantial degree of flexibility, with cable-mounted ion sources and demountable target chambers. This enables wide ranges of workpiece size and shape to be accommodated. The latest development at Harwell is the large 'Blue Tank' ion implantation machine, currently the biggest in the world. This can treat workpieces up to 2 metres maximum dimension and 1 tonne weight using a bucket-type ion source capable of generating 35 mA of nitrogen ion beam current over an 800 mm diameter treatment area. This machine enables increased flexibility and reduced unit treatment costs for nitrogen ion implantation. Uptake of nitrogen ion implantation in British industry is increasing steadily. Key market sectors include the plastics processing industry (for extrusion screws, moulds and dies), as well as many other engineering sectors. A useful accessory to ion implantation developed at Harwell in conjunction with Millspin Limited, monitors nitrogen ion dose colour changes in anodised tantalum which can be compared against a calibrated standard. Accuracies of around 20 % at 2.5 x 10 17 nitrogen ions.cm -2 dose are achievable. (J.P.N.)

Easy digital engineering

International Nuclear Information System (INIS)

Jin, Dal Bok

2002-02-01

This book lists basic of digital engineering, number system and digital code, Boolean algebra and basic logic circuit, simplify of logical expression, combinational circuit, arithmetic circuit, multivibrator circuit, sequential circuit, memory unit of semiconductor and logical element for program, D/A converter and A/D converter, logic element and integrated circuit and logic circuit and micro controller. It has exercises and answers about digital engineering and summary in the end of each chapter.

Advances in imaging and electron physics the scanning transmission electron microscope

CERN Document Server

Hawkes, Peter W

2009-01-01

Advances in Imaging and Electron Physics merges two long-running serials--Advances in Electronics and Electron Physics and Advances in Optical and Electron Microscopy. This series features extended articles on the physics of electron devices (especially semiconductor devices), particle optics at high and low energies, microlithography, image science and digital image processing, electromagnetic wave propagation, electron microscopy, and the computing methods used in all these domains.  This particular volume presents several timely articles on the scanning transmission electron microscope. Updated with contributions from leading international scholars and industry experts Discusses hot topic areas and presents current and future research trends Provides an invaluable reference and guide for physicists, engineers and mathematicians.

Activation of Engineering Students with Clickers

DEFF Research Database (Denmark)

Andersen, Shuang Ma

2011-01-01

Electronic voting system - clickers (Mentometer®) were implemented in a secondary engineering subject: Materials Chemistry, which is a 6 ECTS point course, 4 hours each week at Engineering Faculty, University of Southern Denmark. Both teaching material and evaluation were efficiently conducted vi...

Engineering Electrochemical Setups for Electron Microscopy of Liquid Processes

DEFF Research Database (Denmark)

Jensen, Eric; Burrows, Andrew

This work focuses on creating tools for imaging liquid samples at atmospheric pressure and room temperature in two different electron microscopes; the scanning electron microscope (SEM) and the transmission electron microscope (TEM). The main focus of the project was the fabrication of the two sy...

The growth of tissue engineering.

Science.gov (United States)

Lysaght, M J; Reyes, J

2001-10-01

This report draws upon data from a variety of sources to estimate the size, scope, and growth rate of the contemporary tissue engineering enterprise. At the beginning of 2001, tissue engineering research and development was being pursued by 3,300 scientists and support staff in more than 70 startup companies or business units with a combined annual expenditure of over $600 million. Spending by tissue engineering firms has been growing at a compound annual rate of 16%, and the aggregate investment since 1990 now exceeds $3.5 billion. At the beginning of 2001, the net capital value of the 16 publicly traded tissue engineering startups had reached $2.6 billion. Firms focusing on structural applications (skin, cartilage, bone, cardiac prosthesis, and the like) comprise the fastest growing segment. In contrast, efforts in biohybrid organs and other metabolic applications have contracted over the past few years. The number of companies involved in stem cells and regenerative medicine is rapidly increasing, and this area represents the most likely nidus of future growth for tissue engineering. A notable recent trend has been the emergence of a strong commercial activity in tissue engineering outside the United States, with at least 16 European or Australian companies (22% of total) now active.

Electronic medical history designed by a multidisciplinary unit mastology; Historia clinica electronica disenada por una unidad de mastologia multidisciplinaria

Energy Technology Data Exchange (ETDEWEB)

Camejo, N.; Castillo, C.; Vaca, N.; Camargo, B.; Artagaveytia, N.; Acuna, S.; Milans, S.; Lavina, G.; Carzoglio, J.; Jacobo, O.; Pressa, C.; Delgado, L. [Servicio de Oncologia, Hospital de Clinicas, Montevideo (Uruguay)

2012-11-15

Full text: Objective: To facilitate the collection, organization and analysis of data from patients Unit assisted in Mastology by producing an electronic health record. Materials and Methods: We evaluated forms provided by medical oncologists, radio therapists, radiologists, pathologists, and plastic surgeons mastologists collect data interrogation, physical examination, complementary examinations, diagnoses, anatomy pathological evolution and treatment instituted and generating the system was computerized {sup U}nit Mastology - Electronic Health Record ( UMAHCE){sup .} Results: The story was designed in modules that collect data on instances arising diagnostic, treatment and monitoring of patients. Each module is represented by an icon that changes color to enter data, allowing the objectify doctor if they are or not the data for that module. The system can attach images recorded by breast exam photos, photos of study, imaging (mammography, CT, MRI) in the same way that the surgeon to enter the protocol surgical or anatomical pathologist enter a pathological report of a study untimely or after definitive surgery. The system can generate an automatic report of the input data that can be printed and placed in the patient's medical history. It also can generate the e mail alerts doctors on pathological results were entered into regarding the diagnosis or treatment breast cancer (eg, mammography B I-Rads 4 or 5, report positive cytologic puncture malignancy, H R and Her status). Conclusions: We developed an electronic medical record that allows different doctors involved in the management of breast disease can be accessed through the web regardless of where they are ( pathology laboratory, room radiology reports, clinic, operation theater), both for information about a patient to enter data the same in relation to their specialty. Moreover, homogenize manages the type and quality of the data and therefore can improve the care and research activities as well as

The record of electrical and communication engineering conversazione Tohoku University Volume 63, No. 3

Science.gov (United States)

1995-05-01

English abstracts contained are from papers authored by the research staff of the Research Institute of Electrical Communication and the departments of Electrical Engineering, Electrical Communications, Electronic Engineering, and Information Engineering, Tohoku University, which originally appeared in scientific journals in 1994. The abstracts are organized under the following disciplines: electromagnetic theory; physics; fundamental theory of information; communication theory and systems; signal and image processing; systems control; computers; artificial intelligence; recording; acoustics and speech; ultrasonic electronics; antenna, propagation, and transmission; optoelectronics and optical communications; quantum electronics; superconducting materials and applications; magnetic materials and magnetics; semiconductors; electronic materials and parts; electronic devices and integrated circuits; electronic circuits; medical electronics and bionics; measurements and applied electronics; electric power; and miscellaneous.

Stitching Codeable Circuits: High School Students' Learning About Circuitry and Coding with Electronic Textiles

Science.gov (United States)

Litts, Breanne K.; Kafai, Yasmin B.; Lui, Debora A.; Walker, Justice T.; Widman, Sari A.

2017-10-01

Learning about circuitry by connecting a battery, light bulb, and wires is a common activity in many science classrooms. In this paper, we expand students' learning about circuitry with electronic textiles, which use conductive thread instead of wires and sewable LEDs instead of lightbulbs, by integrating programming sensor inputs and light outputs and examining how the two domains interact. We implemented an electronic textiles unit with 23 high school students ages 16-17 years who learned how to craft and code circuits with the LilyPad Arduino, an electronic textile construction kit. Our analyses not only confirm significant increases in students' understanding of functional circuits but also showcase students' ability in designing and remixing program code for controlling circuits. In our discussion, we address opportunities and challenges of introducing codeable circuit design for integrating maker activities that include engineering and computing into classrooms.

Mechatronics Engineering Education

OpenAIRE

Grimheden, Martin

2006-01-01

Since its emergence in the late 1960s, mechatronics has become well-established as an academic subject, and is now researched and taught at a large number of universities worldwide. The most widely-used definition of the subject today is centered on the synergistic integration of mechanical engineering, electronics, and intelligent computer control. The aim of this thesis is to work between the disciplines of engineering education and mechatronics to address both the question of the identity ...

Environmental optimisation of natural gas fired engines. Measurement on four different engines. Project report

Energy Technology Data Exchange (ETDEWEB)

Kvist, T.

2010-10-15

The emissions of NO{sub x}, CO and UHC as well as the composition of the hydrocarbon emissions were measured for four different stationary lean burn natural gas fired engines installed at different combined heat and power (CHP) units in Denmark. The units have been chosen to be representative for the natural gas engine based on power production in Denmark. The NO{sub x} emissions were varied from around 200 to 500 mg/m3(n) by varying the ignition timing and the excess of air. For each of the examined engines measurements were conducted at different combinations of ignition timing and excess of air. The measurements showed the NO{sub x} emissions were relatively more sensitive to engine setting than UHC, CO and formaldehyde emissions. By reducing the NO{sub x} emissions to 40 % of the initial value (from 500 to 200 mg/m3(n)) the UHC emission were increased by 10 % to 50 % of the initial value. The electrical efficiency was reduced by 0,5 to 1,0 % point. (Author)

Uniting Electron Crystallography and Powder Diffraction

CERN Document Server

Shankland, Kenneth; Meshi, Louisa; Avilov, Anatoly; David, William

2012-01-01

The polycrystalline and nanocrystalline states play an increasingly important role in exploiting the properties of materials, encompassing applications as diverse as pharmaceuticals, catalysts, solar cells and energy storage. A knowledge of the three-dimensional atomic and molecular structure of materials is essential for understanding and controlling their properties, yet traditional single-crystal X-ray diffraction methods lose their power when only polycrystalline and nanocrystalline samples are available. It is here that powder diffraction and single-crystal electron diffraction techniques take over, substantially extending the range of applicability of the crystallographic principles of structure determination.  This volume, a collection of teaching contributions presented at the Crystallographic Course in Erice in 2011, clearly describes the fundamentals and the state-of-the-art of powder diffraction and electron diffraction methods in materials characterisation, encompassing a diverse range of discipl...

ELEC-2002: ELECTRONICS IN HEP

CERN Multimedia

Technical Training; Davide.Vite@cern.ch

2001-01-01

ELEC-2002 is a 15-session modern electronic course, given by CERN physicists and engineers, in a new format within the framework of the Technical Training Programme. This course is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2002 will composed of two terms: sessions will take place on Tuesdays and Thursdays, from 14h00 to 16h30, in the Training Centre Auditorium, bldg. 593. Winter term: Readout and system electronics for physics (January-February 2002) Introduction: the basics of electronics (Philippe Farthouat, 15 January) Analogue signal processing (Francis Anghinolfi, 17 January) Analogue to digital conversions and data transmission (Philippe Farthouat, 22 January) Digital design with Field-Programmable Gate Arrays (Erik van der Bij, 24 January) Modular el...

KNOVEL: A NEW SERVICE FOR THE ENGINEERING COMMUNITY

CERN Multimedia

2001-01-01

Electronic books available on trial at CERN Electronic preprints and journals have become tools used on a daily basis, but so far the CERN Library did not provide a significant collection of electronic books. This is now about to change, so searching for scientific information, and in particular engineering-related references, is now easier than ever before. CERN has access to the electronic book collection via Knovel on a trial base until Xmas. Knovel has a database of some of the leading engineering reference handbooks and conference proceedings, published by Reed Elsevier, ASME, ASM, Butterworth, CRC Press, McGraw-Hill and others. The full-text of all e-books can be searched simultaneously. Another Knovel feature allows users to search for data (materials properties) across the whole digital collection. The Web search engine and display interface has been developed to support a wide range of information and file types: text, tables, equations, graphics, figures. This new resource is linked to from the Libr...

DEVELOPMENT OF OPERATING DRIVE SYSTEMS IN ENGINEERING EQUIPMENT

Directory of Open Access Journals (Sweden)

A. A. Kotlobai

2015-01-01

Full Text Available Engineering machines being in operational service with military units of  engineer troops are fit to their purpose and their application is relevant in modern conditions. Maintenance of operating conditions in engineering equipment which was produced earlier by the USSR enterprises is considered as a rather complicated task due to lack of spare parts because their production has been discontinued.One of the approaches used for maintenance of engineering equipment combat capabilities is modernization of operating drive systems that presupposes replacement of mechanical systems in working element drives by hydrostatic drives which are realized while using modern element base. Usage of hydraulic units in drive systems being in mass production for replacement of mechanical systems manufactured earlier in small batches makes it possible to reduce labour inputs for maintenance and repair of machines. The paper presents some possibilities for development of operating drive systems in engineering equipment. The proposed approach is given through an example of  engineering obstacle-clearing vehicle (IMR-2M and excavation machines (MDK-3 and MDK-2M.Application of a hydraulic drive in working elements of the excavation machines permits to withdraw from cardan  shafts, a gear box, a rotary gear and an overload clutch. A hydraulic motor of the cutter and thrower drive is mounted  on a working element gearbox. While executing modernization of hydraulic systems in excavation machines a pump unit has been proposed for the cutter and thrower drive which consists of a controlled pump and a system for automatic maintenance of the pump operational parameters. While developing the operating drive systems in engineering equipment in accordance with the proposed requirements it is possible to simplify drive systems of working elements and  ensure reliable machinery operation in the units of engineer troops. 

Electronic Signature Policy

Science.gov (United States)

Establishes the United States Environmental Protection Agency's approach to adopting electronic signature technology and best practices to ensure electronic signatures applied to official Agency documents are legally valid and enforceable

Tracking the Implementation of Electronic Medical Records in Dubai, United Arab Emirates, Using an Adoption Benchmarking Tool.

Science.gov (United States)

El-Hassan, Osama; Sharif, Amer; Al Redha, Mohammad; Blair, Iain

2017-01-01

In the United Arab Emirates (UAE), health services have developed greatly in the past 40 years. To ensure they continue to meet the needs of the population, innovation and change are required including investment in a strong e-Health infrastructure with a single transferrable electronic patient record. In this paper, using the Emirate of Dubai as a case study, we report on the Middle East Electronic Medical Record Adoption Model (EMRAM). Between 2011-2016, the number of participating hospitals has increased from 23 to 33. Currently, while 20/33 of hospitals are at Stage 2 or less, 10/33 have reached Stage 5. Also Dubai's median EMRAM score in 2016 (2.5) was higher than the scores reported from Australia (2.2), New Zealand (2.3), Malaysia (0.06), the Philippines (0.06) and Thailand (0.5). EMRAM has allowed the tracking of the progress being made by healthcare facilities in Dubai towards upgrading their information technology infrastructure and the introduction of electronic medical records.

40 CFR 1045.230 - How do I select engine families?

Science.gov (United States)

2010-07-01

... POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS Certifying... control for engine operation, other than governing (i.e., mechanical or electronic). (6) The numerical... engine family. You may include dedicated-fuel versions of this same engine model in the same engine...

Women Break an Engineering Barrier: While Other Engineering Disciplines Stumble, BME Represents a Success Story in Attracting American Women to a Male-Dominated Field.

Science.gov (United States)

Gutierrez, Claudia; Paulosky, Meaghan; Aguinaldo, Angeline; Gerhart, Jackie

2017-01-01

While the field of engineering as a whole is largely male-dominated, biomedical engineering (BME) is one area poised to overturn this trend. Women in the United States were awarded only 20% of all engineering B.S. degrees in 2015; in BME, however, 40.9% of the degree recipients were women. This stands in stark contrast to the more traditional fields of mechanical and electrical engineering, where women were awarded just 13.2% and 12.5% of B.S. degrees, respectively. This trend toward more female participation in BME continues at both the M.S. and Ph.D. degree levels. In fact, in 2015, BME had the highest percentage of female engineering M.S. degree recipients in the United States of all engineering disciplines, according to the American Society for Engineering Education (Figure 1).

Electronic tap-changer for distribution transformers

Energy Technology Data Exchange (ETDEWEB)

Faiz, Jawad [Tehran Univ. (Iran, Islamic Republic of). Univ. College of Engineering; Siahkolah, Behzad [Kavandish Company, Tehran (Iran, Islamic Republic of)

2011-07-01

This reference collects all relevant aspects electronic tap-changer and presents them in a comprehensive and orderly manner. It explains logically and systematically the design and optimization of a full electronic tap-changer for distribution transformers. The book provides a fully new insight to all possible structures of power section design and categorizes them comprehensively, including cost factors of the design. In the control section design, the authors review mechanical tap-changer control systems and they present the modeling of a full electronic tap-changer as well as a closed-loop control of the full-electronic tap-changer. The book is written for electrical engineers in industry and academia but should be useful also to postgraduate students of electrical engineering. (orig.)

GENDER ISSUES: Perceptions of Readiness in Selected Units

National Research Council Canada - National Science Library

1999-01-01

.... More than 13,000 women have joined these units.3 Among the units that have opened to women are Army smoke and chemical companies, forward support battalions, air defense artillery headquarters' units, military police units, and engineer companies...

Electrical principles and technology for engineering

CERN Document Server

Bird, John

1995-01-01

The aim of this book is to introduce students to the basic electrical and electronic principles needed by technicians in fields such as electrical engineering, electronics and telecommunications. The emphasis is on the practical aspects of the subject, and the author has followed his usual successful formula, incorporating many worked examples and problems (answers supplied) into the learning process.Electrical Principles and Technology for Engineering is John Bird's core text for Further Education courses at BTEC levels N11 and N111 and Advanced GNVQ. It is also designed to provide a comprehe

Performance and combustion analysis of Mahua biodiesel on a single cylinder compression ignition engine using electronic fuel injection system

Directory of Open Access Journals (Sweden)

Gunasekaran Anandkumar

2016-01-01

Full Text Available In this investigation, experiment is carried out on a 1500 rpm constant speed single cylinder Diesel engine. The test is carried out with Neat diesel, neat biodiesel, and blend B20. The engine considered was run with electronic fuel injection system supported by common rail direct injection to obtain high atomization and effective air utilization inside the combustion chamber. The performance of the engine in terms of break thermal efficiency and brake specific energy consumption was found and compared. The B20 blend shows 1.11% decrease in break thermal efficiency and 3.35% increase in brake specific energy consumption than diesel. The combustion characteristics found are in-cylinder pressure, rate of pressure rise, and heat release rate and compared for peak pressure load to understand the nature of combustion process. For each fuel test run, the maximum peak pressure is observed at part load condition. The rate of change of pressure and heat release rate of diesel is high compared to pure biodiesel and B20 blend. The diffusion combustion is observed to be predominant in case of B100 than B20 and Neat diesel.

Towards atomic scale engineering of rare-earth-doped SiAlON ceramics through aberration-corrected scanning transmission electron microscopy

International Nuclear Information System (INIS)

Yurdakul, Hilmi; Idrobo, Juan C.; Pennycook, Stephen J.; Turan, Servet

2011-01-01

Direct visualization of rare earths in α- and β-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of β-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in α-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in β-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.

Monitor tables for electron beams in radiotherapy

International Nuclear Information System (INIS)

Christ, G.; Dohm, O.S.

2007-01-01

The application of electron beams in radiotherapy is still based on tables of monitor units, although 3-D treatment planning systems for electron beams are available. This have several reasons: The need for 3-D treatment planning is not recognized; there is no confidence in the calculation algorithm; Monte-Carlo algorithms are too time-consuming; and the effort necessary to measure basic beam data for 3-D planning is considered disproportionate. However, the increasing clinical need for higher dosimetric precision and for more conformal electron beams leads to the requirement for more sophisticated tables of monitor units. The present paper summarizes and discusses the main aspects concerning the preparation of tables of monitor units for electron beams. The measurement equipment and procedures for measuring basic beam data needed for tables of monitor units for electron beams are described for a standard radiation therapy linac. The design of tables of monitor units for standard electron applicators is presented; this design can be extended for individual electron inserts, to variable applicator surface distances, to oblique beam incidence, and the use of bolus material. Typical data of an Elekta linac are presented in various tables. (orig.)

Fostering Passion among First Year Engineering Students

Science.gov (United States)

Mazumder, Quamrul H.

2010-01-01

Engineering is a complex field of study. Declining enrollment in engineering programs in the United States is of concern and understanding the various factors that contribute to this decline is in order. Fostering a higher level of student engagement with the content may foster passion towards engineering which could increase academic competency…

The effects of radiation on electronic systems

International Nuclear Information System (INIS)

Messenger, G.C.; Ash, M.S.

1986-01-01

This book is the first unified treatment of the analysis and design methods for protection of principally electronic systems from the deleterious effects of nuclear and electro-magnetic radiation. Coverage spans from a detailed description of the nuclear radiation sources to pertinent semiconductor physics, then to hardness assurance. This work combines the disciplines of solid state physics, semiconductor physics, circuit engineering, nuclear physics, together with electronics and electromagnetic theory into a book that can be used as a text with problems at the end of the majority of the chapters. Written by veterans in the field, the most significant feature of this book is its comprehensive treatment of the phenomena involved. This treatment includes the analysis and design of the effect of nuclear radiation on electronic systems from the experimental, theoretical, and engineering viewpoints. Unique pedagogical attempts are employed to make the material more understandable from the position of an enlightened engineering and scientific readership whose task is the design and analysis of radiation hardened electronic systems

Introduction to Waste Engineering

DEFF Research Database (Denmark)

Christensen, Thomas Højlund

2011-01-01

Solid waste management as introduced in Chapter 1.1 builds in many ways on engineering. Waste engineering here means the skills and ability to understand quantitatively how a waste management system works in such a detail that waste management can be planned, facilities can be designed and sited......) regional plans for waste management, including (3) the selection of main management technologies and siting of facilities, (4) the design of individual technological units and, for example, (5) the operation of recycling schemes within a municipality. This chapter gives an introduction to waste engineering...

Combined UMC- DFT prediction of electron-hole coupling in unit cells of pentacene crystals.

Science.gov (United States)

Leal, Luciano Almeida; de Souza Júnior, Rafael Timóteo; de Almeida Fonseca, Antonio Luciano; Ribeiro Junior, Luiz Antonio; Blawid, Stefan; da Silva Filho, Demetrio Antonio; da Cunha, Wiliam Ferreira

2017-05-01

Pentacene is an organic semiconductor that draws special attention from the scientific community due to the high mobility of its charge carriers. As electron-hole interactions are important aspects in the regard of such property, a computationally inexpensive method to predict the coupling between these quasi-particles is highly desired. In this work, we propose a hybrid methodology of combining Uncoupled Monte Carlo Simulations (UMC) and Density functional Theory (DFT) methodologies to obtain a good compromise between computational feasibility and accuracy. As a first step in considering a Pentacene crystal, we describe its unit cell: the Pentacene Dimer. Because many conformations can be encountered for the dimer and considering the complexity of the system, we make use of UMC in order to find the most probable structures and relative orientations for the Pentacene-Pentacene complex. Following, we carry out electronic structure calculations in the scope of DFT with the goal of describing the electron-hole coupling on the most probable configurations obtained by UMC. The comparison of our results with previously reported data on the literature suggests that the methodology is well suited for describing transfer integrals of organic semiconductors. The observed accuracy together with the smaller computational cost required by our approach allows us to conclude that such methodology might be an important tool towards the description of systems with higher complexity.

Developing an Integration Infrastructure for Distributed Engine Control Technologies

Science.gov (United States)

Culley, Dennis; Zinnecker, Alicia; Aretskin-Hariton, Eliot; Kratz, Jonathan

2014-01-01

Turbine engine control technology is poised to make the first revolutionary leap forward since the advent of full authority digital engine control in the mid-1980s. This change aims squarely at overcoming the physical constraints that have historically limited control system hardware on aero-engines to a federated architecture. Distributed control architecture allows complex analog interfaces existing between system elements and the control unit to be replaced by standardized digital interfaces. Embedded processing, enabled by high temperature electronics, provides for digitization of signals at the source and network communications resulting in a modular system at the hardware level. While this scheme simplifies the physical integration of the system, its complexity appears in other ways. In fact, integration now becomes a shared responsibility among suppliers and system integrators. While these are the most obvious changes, there are additional concerns about performance, reliability, and failure modes due to distributed architecture that warrant detailed study. This paper describes the development of a new facility intended to address the many challenges of the underlying technologies of distributed control. The facility is capable of performing both simulation and hardware studies ranging from component to system level complexity. Its modular and hierarchical structure allows the user to focus their interaction on specific areas of interest.

Modern dictionary of electronics

CERN Document Server

Graf, Rudolf F

1999-01-01

Included in this fully revised classic are well over 28,000 terms, phrases, acronyms, and abbreviations from the ever-expanding worlds of consumer electronics, optics, microelectronics, computers, communications, and medical electronics. From the basic elements of theory to the most cutting-edge circuit technology, this book explains it all in both words and pictures.For easy reference, the author has provided definitions for standard abbreviations and equations as well as tables of SI (International System of Units) units, measurements, and schematic symbolsModern Dictionary of Electronics is

Trend of supersonic aircraft engine. Choonsokukiyo engine no doko

Energy Technology Data Exchange (ETDEWEB)

Yashima, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

1994-05-01

The present paper explained the R and D trend of supersonic aircraft engine in Europe, USA and Japan. Taking the high speed flight resistance into consideration, the engine must be characterized by its high exhaust gas speed and high specific thrust (ratio of thrust to the airflow rate) to secure strong thrust by a low airflow rate. Therefore, the turbojet is appropriate. However to reduce the fuel consumption during the cruising flight, the turbofan is normally used with a low by-pass ratio of 0.2 to 0.9. The thrust-to-weight ratio (thrust per unit weight) of low by-pass ratio turbofan engine equipped with afterburner is 7 to 8 in case of stronger thrust than 70kN. Its target value of development is 10. The specific thrust which is a performance parameter of engine exceeds 120s for the fighter engine and is about 30s for the passenger plane engine. The turbine inlet temperature is 2073K at the stage of element research. The overall pressure ratio ranges from 25 to 30. The reheating turbofan engine experimentally built for the research in Japan is 34kN in thrust and 7 in thrust-to-weight ratio. 8 refs., 9 figs.

Energy-related doctoral scientists and engineers in the United States, 1975

Energy Technology Data Exchange (ETDEWEB)

1977-11-01

The pursuit of a vigorous research and development program to provide renewable and other resources to meet U. S. energy needs in the next century is an important objective of President Carter's National Energy Plan. A highly educated and motivated pool of engineers and scientists must be available for energy research and development if this objective is to be achieved. This report provides, for the first time, information about the number and characteristics of doctoral-level engineers and scientists in primarily energy-related activities. These data for the year 1975 will become part of the data base for a program of continuing studies on the employment and utilization of all scientists and engineers involved in energy-related activities. Information is provided for employment in the following fields: mathematics; physics/astronomy; chemistry; Earth, Environment, and Marine Sciences; Engineering; Life Sciences; Psychology; Social Sciences; Arts and Humanities; and Education and Business.

Engineering Resilience Into The Marine Expeditionary Units Resupply System Through Military Foraging

Science.gov (United States)

2017-09-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release. Distribution is unlimited. ENGINEERING ...ONLY (Leave blank) 2. REPORT DATE September 2017 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE ENGINEERING RESILIENCE...to the resilience of the MEU platoons and squads. 14. SUBJECT TERMS systems engineering , modeling, foraging, energy, water, resupply, ExtendSim

From bench to application: current practices in tissue engineering and its realisation at maxillofacial units in Germany, Austria and Switzerland.

Science.gov (United States)

Smeets, Ralf; El-Moawen, Ahmed; Jung, Ole; Hanken, Henning; Hartjen, Philip; Heiland, Max; Kansy, Katinka; Kloss, Frank; Kolk, Andreas

2014-10-01

Over the last 20 years, the highly interdisciplinary field of tissue engineering (TE) has become an established subspecialty in research facilities all over the world. Numerous methods and protocols are available for various research intentions and aims, but there are no data indicating which of these methods and resources are generally used. This study is an overview of the resources and methods that are commonly applied in TE research in general, and in the field of oral and maxillofacial surgery (OMFS) in Germany, Austria and Switzerland. The DÖSAK collaborative group for TE developed a detailed questionnaire and collected information from participating university hospitals in these three countries. We evaluated the availability of research facilities, in vitro realisation and in vivo designs for animal studies in these departments. 11 units who replied, out of 35 we contacted, conducted research on bone regeneration in interdisciplinary research facilities. 10 departments used xenogeneic and alloplastic scaffolds for in vitro and in vivo applications. In this case, the most commonly utilised trademarks were Bio-Oss(®) and CERASORB(®). 9 units used osteoblasts (73%) and 10 proliferation assays in vitro, whereas rats served as the standard animal model for histology/immunohistochemistry in 6. All research units were interested in establishing a platform for research exchange and communication. This study shows that tissue engineering is well established and highly accepted in most participating university hospitals and research facilities. The presented data, together with data published in a foregoing paper will help arrange more readily available standardised procedures for further investigations. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.