WorldWideScience

Sample records for electronic technology technical

  1. Electronic technology

    International Nuclear Information System (INIS)

    Kim, Jin Su

    2010-07-01

    This book is composed of five chapters, which introduces electronic technology about understanding of electronic, electronic component, radio, electronic application, communication technology, semiconductor on its basic, free electron and hole, intrinsic semiconductor and semiconductor element, Diode such as PN junction diode, characteristic of junction diode, rectifier circuit and smoothing circuit, transistor on structure of transistor, characteristic of transistor and common emitter circuit, electronic application about electronic equipment, communication technology and education, robot technology and high electronic technology.

  2. Electron Technology: ELTE 2016

    Science.gov (United States)

    Pisarkiewicz, Tadeusz; Kucewicz, Wojciech

    2016-12-01

    In this paper we present a review of research results and technical accomplishments presented by researchers from technical universities, governmental institutes and research companies during the XIIth Scientific Conference Electron Technology, ELTE 2016. This review is based on materials presented at four topical conference sessions: Microelectronics and Nanoelectronics, Photonics, Materials and Technologies, and Microsystems and also on materials presented by invited speakers at two dedicated sessions. Oral sessions were accompanied by the poster sessions. In effect about 50 papers gathered in this volume reflect the topics discussed at the Conference. A short description of technological and measurement possibilities in the laboratories of Academic Centre for Materials and Nanotechnology and also in the Department of Electronics of the Faculty of Computer Science, Electronics and Telecommunications AGH UST are given.

  3. Electrical and Electronics Technical Team Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-06-01

    The Electrical and Electronics Technical Team’s (EETT's) mission is to enable cost-effective, smaller, lighter, and efficient power electronics and electric motors for electric traction drive systems (ETDSs) while maintaining performance of internal combustion engine (ICE)-based vehicles. The EETT also identifies technology gaps, establishes R&D targets, develops a roadmap to achieve technical targets and goals, and evaluates the R&D progress toward meeting the established R&D targets and goals.

  4. Using High-Technology Simulators to Prepare Anesthesia Providers Before Implementation of a New Electronic Health Record Module: A Technical Report.

    Science.gov (United States)

    Weintraub, Ari Y; Deutsch, Ellen S; Hales, Roberta L; Buchanan, Newton A; Rock, Whitney L; Rehman, Mohamed A

    2017-06-01

    Learning to use a new electronic anesthesia information management system can be challenging. Documenting anesthetic events, medication administration, and airway management in an unfamiliar system while simultaneously caring for a patient with the vigilance required for safe anesthesia can be distracting and risky. This technical report describes a vendor-agnostic approach to training using a high-technology manikin in a simulated clinical scenario. Training was feasible and valued by participants but required a combination of electronic and manual components. Further exploration may reveal simulated patient care training that provides the greatest benefit to participants as well as feedback to inform electronic health record improvements.

  5. Information technologies in technical education

    OpenAIRE

    Кравченя, Э. М.

    2013-01-01

    The purpose of researches is working out of the concept of filling of discipline «Information and computer technologies in formation» the first step of higher education entered into curricula was at engineering-pedagogical faculty BNTU. It is shown that as a result of discipline studying there is an expansion of outlook and formation at students of technical college of independent thinking in the field of modern and perspective information technology.

  6. Reforming Technical and Technological Education.

    Science.gov (United States)

    Wilson, David N.

    1993-01-01

    Review of technical and technological educational reform in Brazil, Canada, Germany, Great Britain, Indonesia, Malaysia, Singapore, and Sweden shows that reform takes time to complete effectively, long-term approaches are needed, and reform is linked to industrial development, regional cooperation, and decentralized decision making. (SK)

  7. Research and Development Issues for Interactive Electronic Technical Manuals

    National Research Council Canada - National Science Library

    Ricci, Katrina

    2002-01-01

    ... technologies to support Interactive Electronic Technical Manuals (IETMs). A workshop was conducted at the NAVAIR Orlando, Training Systems Division to discuss the domain and to present current research in this area...

  8. Technical Communicator: A New Model for the Electronic Resources Librarian?

    Science.gov (United States)

    Hulseberg, Anna

    2016-01-01

    This article explores whether technical communicator is a useful model for electronic resources (ER) librarians. The fields of ER librarianship and technical communication (TC) originated and continue to develop in relation to evolving technologies. A review of the literature reveals four common themes for ER librarianship and TC. While the…

  9. Technical Executive Summary in Support of "Can Electronic Medical Record Systems Transform Healthcare?" and "Promoting Health Information Technology"

    National Research Council Canada - National Science Library

    Bigelow, James H; Fonkych, Kateryna; Girosi, Federico

    2005-01-01

    .... The three sections of this paper summarize these documents in the order listed. Report no. 1 estimates the degree to which hospitals and physician practices have adopted electronic medical records (EMRs...

  10. Chemical Technology Division annual technical report 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division`s activities during 1997 are presented.

  11. Chemical Technology Division annual technical report 1997

    International Nuclear Information System (INIS)

    1998-06-01

    The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials and electrified interfaces. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1997 are presented

  12. 1998 Chemical Technology Division Annual Technical Report.

    Energy Technology Data Exchange (ETDEWEB)

    Ackerman, J.P.; Einziger, R.E.; Gay, E.C.; Green, D.W.; Miller, J.F.

    1999-08-06

    The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1998 are presented.

  13. Electronic equipment packaging technology

    CERN Document Server

    Ginsberg, Gerald L

    1992-01-01

    The last twenty years have seen major advances in the electronics industry. Perhaps the most significant aspect of these advances has been the significant role that electronic equipment plays in almost all product markets. Even though electronic equipment is used in a broad base of applications, many future applications have yet to be conceived. This versatility of electron­ ics has been brought about primarily by the significant advances that have been made in integrated circuit technology. The electronic product user is rarely aware of the integrated circuits within the equipment. However, the user is often very aware of the size, weight, mod­ ularity, maintainability, aesthetics, and human interface features of the product. In fact, these are aspects of the products that often are instrumental in deter­ mining its success or failure in the marketplace. Optimizing these and other product features is the primary role of Electronic Equipment Packaging Technology. As the electronics industry continues to pr...

  14. Electronics practice technology

    International Nuclear Information System (INIS)

    1995-01-01

    This book concentrates on electronic technology. It deals with kinds of terminal and mounting such as teflon terminal, steatite terminal, and harmonica terminal, small parts like connector, plug jack, vernier dial, and coupling, termination of wiring, kinds of switch and mounting, a condenser, fixed resistor, trance coil, loading of semiconductor, mounting of high input impedance circuit, mounting of electric power circuit, manufacturing of print substrate and practice of manufacturing for print substrate. This is one of series books on electronic technology.

  15. Another Interface: Electronic Publishing and Technical Services.

    Science.gov (United States)

    Yamamoto, Rumi

    1986-01-01

    Discusses the problems of assimilating electronic publishing within the technical services area of academic libraries: whether to consider electronic journals as acquisitions; how to catalog them; whether to charge users for access to them; and how to preserve online publications for future research. Future trends in electronic publishing are…

  16. Sandia Laboratories technical capabilities: electronics

    International Nuclear Information System (INIS)

    Lundergan, C.D.

    1975-12-01

    This report characterizes the electronics capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

  17. Mathematics for electronic technology

    CERN Document Server

    Howson, D P

    1975-01-01

    Mathematics for Electronic Technology is a nine-chapter book that begins with the elucidation of the introductory concepts related to use of mathematics in electronic engineering, including differentiation, integration, partial differentiation, infinite series, vectors, vector algebra, and surface, volume and line integrals. Subsequent chapters explore the determinants, differential equations, matrix analysis, complex variable, topography, graph theory, and numerical analysis used in this field. The use of Fourier method for harmonic analysis and the Laplace transform is also described. The ma

  18. Japan's electronic packaging technologies

    Science.gov (United States)

    Tummala, Rao R.; Pecht, Michael

    1995-02-01

    The JTEC panel found Japan to have significant leadership over the United States in the strategic area of electronic packaging. Many technologies and products once considered the 'heart and soul' of U.S. industry have been lost over the past decades to Japan and other Asian countries. The loss of consumer electronics technologies and products is the most notable of these losses, because electronics is the United States' largest employment sector and is critical for growth businesses in consumer products, computers, automobiles, aerospace, and telecommunications. In the past there was a distinction between consumer and industrial product technologies. While Japan concentrated on the consumer market, the United States dominated the industrial sector. No such distinction is anticipated in the future; the consumer-oriented technologies Japan has dominated are expected to characterize both domains. The future of U.S. competitiveness will, therefore, depend on the ability of the United States to rebuild its technological capabilities in the area of portable electronic packaging.

  19. Technical writing in the radiologic technology curriculum.

    Science.gov (United States)

    Bell, R

    1979-01-01

    Although courses in technical writing are no longer suggested in the Curriculum Guide for Programs in Radiologic Technology, the writer believes that writing is essential to the growth of the profession and development of the professional. Emphasis is placed on some of the benefits that accrue to students who are exposed to technical writing as part of their technology curriculum.

  20. Technical Training: ELEC-2005: Electronics in High Energy Physics

    CERN Multimedia

    Monique Duval

    2005-01-01

    CERN Technical Training 2005: Learning for the LHC! ELEC-2005: Electronics in High Energy Physics - Spring Term ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the successful ELEC-2002 course series. This comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms: the Winter Term, Introduction to electronics in HEP, already took place; the next three Terms will run throughout the year: Spring Term: Integrated circuits and VLSI technology for physics (March, 6 lectures) - now open for registration Summer Term: System electronics for physics: Issues (May, 7 lectures) Autumn Term: Ele...

  1. Electronic components and technology

    CERN Document Server

    Sangwine, Stephen

    2007-01-01

    Most introductory textbooks in electronics focus on the theory while leaving the practical aspects to be covered in laboratory courses. However, the sooner such matters are introduced, the better able students will be to include such important concerns as parasitic effects and reliability at the very earliest stages of design. This philosophy has kept Electronic Components and Technology thriving for two decades, and this completely updated third edition continues the approach with a more international outlook.Not only does this textbook introduce the properties, behavior, fabrication, and use

  2. Technical Training: ELEC-2005 - Electronics in High Energy Physics

    CERN Multimedia

    Monique Duval

    2005-01-01

    Learning for the LHC! ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the successful ELEC-2002 course series. This comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms that will run throughout the year: Winter Term: Introduction to electronics in HEP (January-February, 6 lectures) Spring Term: Integrated circuits and VLSI technology for physics (March, 6 lectures) Summer Term: System electronics for physics: Issues (May, 7 lectures) Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) Lectures within each Term will take place on Tuesdays an...

  3. VIRTUALIZATION TECHNICAL THINKING WITHIN THE INFORMATION TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Robert Lis

    2014-11-01

    Full Text Available The article presents the possibilities of virtualization technical thinking within the information technology. This question expresses the need for virtualization of existing information systems to improve the conduct of business by the company. In resulting virtualization of the technical-computer thought on against existing needs of the functioning of 16-bit systems in 64-bit systems. Enables cost-effective use of excess capacity existing computing resources.

  4. Drafting & Design Technology. Technical Committee Report.

    Science.gov (United States)

    Idaho State Dept. of Education, Boise. Div. of Vocational Education.

    This Technical Committee Report prepared by industry representatives in Idaho lists the skills currently necessary for an employee in that state to obtain a job in drafting and design technology, retain a job once hired, and advance in that occupational field. (Task lists are grouped according to duty areas generally used in industry settings, and…

  5. Applied Welding Technology. Technical Committee Report.

    Science.gov (United States)

    Idaho State Dept. of Education, Boise. Div. of Vocational Education.

    This Technical Committee Report prepared by industry representatives in Idaho lists the skills currently necessary for an employee in that state to obtain a job in applied welding technology, retain a job once hired, and advance in that occupational field. (Task lists are grouped according to duty areas generally used in industry settings, and are…

  6. Advanced thermal management technologies for defense electronics

    Science.gov (United States)

    Bloschock, Kristen P.; Bar-Cohen, Avram

    2012-05-01

    Thermal management technology plays a key role in the continuing miniaturization, performance improvements, and higher reliability of electronic systems. For the past decade, and particularly, the past 4 years, the Defense Advanced Research Projects Agency (DARPA) has aggressively pursued the application of micro- and nano-technology to reduce or remove thermal constraints on the performance of defense electronic systems. The DARPA Thermal Management Technologies (TMT) portfolio is comprised of five technical thrust areas: Thermal Ground Plane (TGP), Microtechnologies for Air-Cooled Exchangers (MACE), NanoThermal Interfaces (NTI), Active Cooling Modules (ACM), and Near Junction Thermal Transport (NJTT). An overview of the TMT program will be presented with emphasis on the goals and status of these efforts relative to the current State-of-the-Art. The presentation will close with future challenges and opportunities in the thermal management of defense electronics.

  7. The Office of Industrial Technologies technical reports

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    The US Department of Energy's Office of Industrial Technologies (OIT) conducts R D activities which focus on the objectives of improving energy efficiency and providing for fuel flexibility within US industry in the area of industrial energy conservation. The Office also conducts programs to reduce waste generation, increase recycling efforts, and improve the use of wastes as process feedstocks. An active program of technology transfer and education supports these activities and encourages adoption of new technologies. To accomplish these objectives OIT cooperates with the private sector to identify its technological needs and to share R D efforts. R D is conducted to the point that a new technology is shown to work and that it can be transferred to the private sector end-users. This bibliography contains information on all scientific and technical reports sponsored by the DOE Industrial Energy Conservation Program during the years 1988--1990.

  8. Technical Services in the Age of Electronic Publishing.

    Science.gov (United States)

    Brownrigg, Edwin; And Others

    1984-01-01

    Examination of the traditional library technical services functions and how they may change with the advent of widespread computer-based electronic publishing emphasizes ways in which technical services will have to adapt in electronic publishing environment. Implications of electronic publishing for library management and budgeting are explored.…

  9. An Application of Fuzzy Theory to Technical Competency Analysis for the Entry-Level Electronic Technician.

    Science.gov (United States)

    Chang, Liang-Te; And Others

    A study was conducted to develop the electronic technical competencies of duty and task analysis by using a revised DACUM (Developing a Curriculum) method, a questionnaire survey, and a fuzzy synthesis operation. The revised DACUM process relied on inviting electronics trade professionals to analyze electronic technology for entry-level…

  10. Accessible Electronic and Information Technology

    Science.gov (United States)

    This Policy establishes EPA's responsibilities and procedures for making its Electronic and Information Technology (EIT) products accessible to all people, including people with disabilities, in accordance with Section 508 of the Rehabilitation Act.

  11. Chemical Technology Division annual technical report, 1996

    International Nuclear Information System (INIS)

    1997-06-01

    CMT is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. It conducts R ampersand D in 3 general areas: development of advanced power sources for stationary and transportation applications and for consumer electronics, management of high-level and low-level nuclear wastes and hazardous wastes, and electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, materials chemistry of electrified interfaces and molecular sieves, and the theory of materials properties. It also operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at ANL and other organizations. Technical highlights of the Division's activities during 1996 are presented

  12. Chemical Technology Division annual technical report, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    CMT is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. It conducts R&D in 3 general areas: development of advanced power sources for stationary and transportation applications and for consumer electronics, management of high-level and low-level nuclear wastes and hazardous wastes, and electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, materials chemistry of electrified interfaces and molecular sieves, and the theory of materials properties. It also operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at ANL and other organizations. Technical highlights of the Division`s activities during 1996 are presented.

  13. Benchmarking foreign electronics technologies

    Energy Technology Data Exchange (ETDEWEB)

    Bostian, C.W.; Hodges, D.A.; Leachman, R.C.; Sheridan, T.B.; Tsang, W.T.; White, R.M.

    1994-12-01

    This report has been drafted in response to a request from the Japanese Technology Evaluation Center`s (JTEC) Panel on Benchmarking Select Technologies. Since April 1991, the Competitive Semiconductor Manufacturing (CSM) Program at the University of California at Berkeley has been engaged in a detailed study of quality, productivity, and competitiveness in semiconductor manufacturing worldwide. The program is a joint activity of the College of Engineering, the Haas School of Business, and the Berkeley Roundtable on the International Economy, under sponsorship of the Alfred P. Sloan Foundation, and with the cooperation of semiconductor producers from Asia, Europe and the United States. Professors David A. Hodges and Robert C. Leachman are the project`s Co-Directors. The present report for JTEC is primarily based on data and analysis drawn from that continuing program. The CSM program is being conducted by faculty, graduate students and research staff from UC Berkeley`s Schools of Engineering and Business, and Department of Economics. Many of the participating firms are represented on the program`s Industry Advisory Board. The Board played an important role in defining the research agenda. A pilot study was conducted in 1991 with the cooperation of three semiconductor plants. The research plan and survey documents were thereby refined. The main phase of the CSM benchmarking study began in mid-1992 and will continue at least through 1997. reports are presented on the manufacture of integrated circuits; data storage; wireless technology; human-machine interfaces; and optoelectronics. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

  14. Final Technical Report: Characterizing Emerging Technologies.

    Energy Technology Data Exchange (ETDEWEB)

    King, Bruce Hardison [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hansen, Clifford [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stein, Joshua [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Riley, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gonzalez, Sigifredo [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-12-01

    The Characterizing Emerging Technologies project focuses on developing, improving and validating characterization methods for PV modules, inverters and embedded power electronics. Characterization methods and associated analysis techniques are at the heart of technology assessments and accurate component and system modeling. Outputs of the project include measurement and analysis procedures that industry can use to accurately model performance of PV system components, in order to better distinguish and understand the performance differences between competing products (module and inverters) and new component designs and technologies (e.g., new PV cell designs, inverter topologies, etc.).

  15. The Next Technology Revolution - Nano Electronic Technology

    Science.gov (United States)

    Turlik, Iwona

    2004-03-01

    Nanotechnology is a revolutionary engine that will engender enormous changes in a vast majority of today's industries and markets, while potentially creating whole new industries. The impact of nanotechnology is particularly significant in the electronics industry, which is constantly driven by the need for higher performance, increased functionality, smaller size and lower cost. Nanotechnology can influence many of the hundreds of components that are typically assembled to manufacture modern electronic devices. Motorola manufactures electronics for a wide range of industries and communication products. In this presentation, the typical components of a cellular phone are outlined and technology requirements for future products, the customer benefits, and the potential impact of nanotechnology on many of the components are discussed. Technology needs include reliable materials supply, processes for high volume production, experimental and simulation tools, etc. For example, even routine procedures such as failure characterization may require the development of new tools for investigating nano-scale phenomena. Business needs include the development of an effective, high volume supply chain for nano-materials and devices, disruptive product platforms, and visible performance impact on the end consumer. An equally significant long-term industry need is the availability of science and engineering graduates with a multidisciplinary focus and a deep understanding of the fundamentals of nano-technology, that can harness the technology to create revolutionary products.

  16. Chemical Technology Division annual technical report, 1985

    International Nuclear Information System (INIS)

    1986-04-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1985 are presented. In this period, CMT conducted research and development in areas that include the following: (1) advanced batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) advanced fuel cells with molten carbonate or solid oxide electrolytes; (3) corrosion-protective coatings for high-strength steel; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methodologies for recovery of energy from municipal waste; (6) nuclear technology related to waste management, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and proof of breeding in a light water breeder reactor; and (7) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL

  17. Chemical Technology Division annual technical report, 1994

    International Nuclear Information System (INIS)

    1995-06-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1994 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion; (3) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from waste streams, concentrating radioactive waste streams with advanced evaporator technology, and producing 99 Mo from low-enriched uranium for medical applications; (6) electrometallurgical treatment of the many different types of spent nuclear fuel in storage at Department of Energy sites; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, and impurities in scrap copper and steel; and the geochemical processes involved in mineral/fluid interfaces and water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL)

  18. Chemical Technology Division, Annual technical report, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

  19. Chemical Technology Division, Annual technical report, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    Highlights of the Chemical Technology (CMT) Division`s activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

  20. Chemical Technology Division annual technical report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    Highlights of the Chemical Technology (CMT) Division`s activities during 1994 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion; (3) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from waste streams, concentrating radioactive waste streams with advanced evaporator technology, and producing {sup 99}Mo from low-enriched uranium for medical applications; (6) electrometallurgical treatment of the many different types of spent nuclear fuel in storage at Department of Energy sites; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, and impurities in scrap copper and steel; and the geochemical processes involved in mineral/fluid interfaces and water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

  1. Chemical Technology Division, Annual technical report, 1991

    International Nuclear Information System (INIS)

    1992-03-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1991 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous and mixed hazardous/radioactive waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources; chemistry of superconducting oxides and other materials of interest with technological application; interfacial processes of importance to corrosion science, catalysis, and high-temperature superconductivity; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL)

  2. Polymer Solidification Technology - Technical Issues and Challenges

    International Nuclear Information System (INIS)

    Jensen, Charles; Kim, Juyoul

    2010-01-01

    Many factors come into play, most of which are discovered and resolved only during full-scale solidification testing of each of the media commonly used in nuclear power plants. Each waste stream is unique, and must be addressed accordingly. This testing process is so difficult that Diversified's Vinyl Ester Styrene and Advanced Polymer Solidification are the only two approved processes in the United States today. This paper summarizes a few of the key obstacles that must be overcome to achieve a reliable, repeatable process for producing an approved Stable Class B and C waste form. Before other solidification and encapsulation technologies can be considered compliant with the requirements of a Stable waste form, the tests, calculations and reporting discussed above must be conducted for both the waste form and solidification process used to produce the waste form. Diversified's VERI TM and APS TM processes have gained acceptance in the UK. These processes have also been approved and gained acceptance in the U. S. because we have consistently overcome technical hurdles to produce a complaint product. Diversified Technologies processes are protected intellectual property. In specific instances, we have patents pending on key parts of our process technology

  3. Electron Conditioning of Technical Aluminium Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Le Pimpec, F

    2004-09-02

    The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (= 1.3, value of many pure elements [1]), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

  4. Chemical technology division: Annual technical report 1987

    Energy Technology Data Exchange (ETDEWEB)

    1988-05-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1987 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries--mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for the electromagnetic continuous casting of steel sheet and for the purification of ferrous scrap; (6) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (7) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for liquids and vapors at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; the thermochemistry of various minerals; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 54 figs., 9 tabs.

  5. Chemical Technology Division annual technical report, 1986

    Energy Technology Data Exchange (ETDEWEB)

    1987-06-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1986 are presented. In this period, CMT conducted research and development in areas that include the following: (1) high-performance batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants, the technology for fluidized-bed combustion, and a novel concept for CO/sub 2/ recovery from fossil fuel combustion; (5) methods for recovery of energy from municipal waste; (6) methods for the electromagnetic continuous casting of steel sheet; (7) techniques for treatment of hazardous waste such as reactive metals and trichloroethylenes; (8) nuclear technology related to waste management, a process for separating and recovering transuranic elements from nuclear waste, and the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor; and (9) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 127 refs., 71 figs., 8 tabs.

  6. Chemical technology division: Annual technical report 1987

    International Nuclear Information System (INIS)

    1988-05-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1987 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries--mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for the electromagnetic continuous casting of steel sheet and for the purification of ferrous scrap; (6) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (7) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for liquids and vapors at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; the thermochemistry of various minerals; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 54 figs., 9 tabs

  7. Chemical Technology Division annual technical report, 1988

    International Nuclear Information System (INIS)

    1989-05-01

    Highlights of the Chemical Technology (CMT) Divisions's activities during 1988 are presented. In this period, CMT conducted research and development in the following areas: (1) high-performance batteries (mainly lithium-alloy/metal sulfide, sodium/metal chloride, and sodium/sulfur); (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (5) methods for recovery of energy from municipal waste and techniques for treatment of hazardous chemical water; (6) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing /sup 99/Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor, and waste management; and (7) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 53 figs., 16 tabs

  8. Chemical Technology Division annual technical report, 1986

    International Nuclear Information System (INIS)

    1987-06-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1986 are presented. In this period, CMT conducted research and development in areas that include the following: (1) high-performance batteries - mainly lithium-alloy/metal sulfide and sodium/sulfur; (2) aqueous batteries (lead-acid, nickel/iron, etc.); (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants, the technology for fluidized-bed combustion, and a novel concept for CO 2 recovery from fossil fuel combustion; (5) methods for recovery of energy from municipal waste; (6) methods for the electromagnetic continuous casting of steel sheet; (7) techniques for treatment of hazardous waste such as reactive metals and trichloroethylenes; (8) nuclear technology related to waste management, a process for separating and recovering transuranic elements from nuclear waste, and the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor; and (9) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of catalytic hydrogenation and catalytic oxidation; materials chemistry for associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; the thermochemistry of zeolites and related silicates; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be the major user of the technical support provided by the Analytical Chemistry Laboratory at ANL. 127 refs., 71 figs., 8 tabs

  9. Chemical Technology Division annual technical report, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

    1993-06-01

    In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous waste, mixed hazardous/radioactive waste, and municipal solid waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, treating water contaminated with volatile organics, and concentrating radioactive waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (EFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials (corium; Fe-U-Zr, tritium in LiAlO{sub 2} in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel` ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, and molecular sieve structures; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL).

  10. Chemical Technology Division annual technical report, 1992

    International Nuclear Information System (INIS)

    Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

    1993-06-01

    In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for fluidized-bed combustion and coal-fired magnetohydrodynamics; (3) methods for treatment of hazardous waste, mixed hazardous/radioactive waste, and municipal solid waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, treating water contaminated with volatile organics, and concentrating radioactive waste streams; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (EFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials (corium; Fe-U-Zr, tritium in LiAlO 2 in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel' ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, and molecular sieve structures; and the geochemical processes involved in water-rock interactions occurring in active hydrothermal systems. In addition, the Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the technical programs at Argonne National Laboratory (ANL)

  11. Technical Integration of Nuclear Hydrogen Production Technology

    International Nuclear Information System (INIS)

    Lee, Ki Young; Park, J. K.; Chang, J. H.

    2009-04-01

    These works focus on the development of attainment indices for nuclear hydrogen key technologies, the analysis of the hydrogen production process and the performance estimation for hydrogen production systems, and the assessment of the nuclear hydrogen production cost. For assessing the degree of attainments in comparison with the final goals of VHTR technologies in progress of researches, subdivided are the prerequisite items confirmed to the NHDD concepts. We developed and applied R and D quality management methodology to meet 'Development of Key Technologies for Nuclear Hydrogen' project. And we also distributed R and D QAM and R and D QAP to each teams and are in operation. The preconceptual flow diagrams of SI, HTSE, and HyS processes are introduced and their material and energy balances have been proposed. The hydrogen production thermal efficiencies of not only the SI process as a reference process but also the HTSE and HyS processes were also estimated. Technical feasibility assessments of SI, HTSE, and HyS processes have been carried out by using the pair-wise comparison and analytic hierarchy process, and it is revealed that the experts are considering the SI process as the most feasible process. The secondary helium pathway across the SI process is introduced. Dynamic simulation codes for the H2S04vaporizer, sulfuric acid and sulfur trioxide decomposers, and HI decomposer on the secondary helium pathway and for the primary and secondary sulfuric acid distillation columns, HIx solution distillation column, and preheater for HI vapor have been developed and integrated

  12. Selling Technology in Technical Advertisements: A Case Study.

    Science.gov (United States)

    Guthrie, James R.

    1995-01-01

    Argues that, as the category of "technical products" has expanded and the public's enthusiasm for such products has lessened, marketing writers have begun to reconsider their approaches to technology in ads. Studies two technical ads in detail, and compares the ways in which they portray technology. (SR)

  13. Gender, Technology, and the History of Technical Communication.

    Science.gov (United States)

    Durack, Katherine T.

    1997-01-01

    Considers why women have been absent from the history of technical communication. Discusses research from the history of technology suggesting that notions of "technology,""work," and "workplace" may be gendered terms. Concludes with several suggestions for defining technical communication so that significant works of…

  14. Extension Learners' Use of Electronic Technology

    Science.gov (United States)

    Guenthner, Joseph F.; Swan, Benjamin G.

    2011-01-01

    Extension clientele use electronic technology for entertainment, communication, and business. Educational programs that use electronic technology can enhance learning. To learn more about use of electronic technology among Extension clientele, we surveyed 80 university students and 135 potato farmers. We found that the farmers were likely to use…

  15. Study on tamper-indicating technology in electronic seals system

    International Nuclear Information System (INIS)

    Xu Xiong; Han Feng; Zuo Guangxia; Zhao Xin; Zhang Quanhu; Di Yuming

    2009-01-01

    To strengthen our national arms control verification technical storage and deepen electronic seals' research, this paper mainly introduces seals' characteristics, functions and work principle, studies on tamper-indicating technology which is a key technology in electronic seals, designs some hardware circuit such as optical transceiver, temperature detection circuit, move detection circuit, re-prized circuit and so on, also designs a software program which is used for recording the destroying or tampering events' information. Experimental results show that electronic seals system can record the destroying or tampering events' information accurately and quickly, and give corresponding tamper-indication. (authors)

  16. Technical and Technological Skills Assessment in Laparoscopic Surgery

    Science.gov (United States)

    Chang, Avril; Vincent, Charles

    2006-01-01

    Objectives: Surgical appraisal and revalidation are key components of good surgical practice and training. Assessing technical skills in a structured manner is still not widely used. Laparoscopic surgery also requires the surgeon to be competent in technological aspects of the operation. Methods: Checklists for generic, specific technical, and technological skills for laparoscopic cholecystectomies were constructed. Two surgeons with >12 years postgraduate surgical experience assessed each operation blindly and independently on DVD. The technological skills were assessed in the operating room. Results: One hundred operations were analyzed. Eight trainees and 10 consultant surgeons were recruited. No adverse events occurred due to technical or technological skills. Mean interrater reliability was kappa=0.88, P=technical and technological skills between trainee and consultant surgeons were significant, Mann-Whitney P=technical and technological skills can be measured to assess performance of laparoscopic surgeons. This technical and technological assessment tool for laparoscopic surgery seems to have face, content, concurrent, and construct validities and could be modified and applied to any laparoscopic operation. The tool has the possibility of being used in surgical training and appraisal. We aim to modify and apply this tool to advanced laparoscopic operations. PMID:17212881

  17. Technical Education--The Key to Sustainable Technological Development

    Science.gov (United States)

    Odo, J. U.; Okafor, W. C.; Odo, A. L.; Ejikeugwu, L. N.; Ugwuoke, C. N.

    2017-01-01

    Technical education has been identified as one of the most effective human resource development that needs to be embraced for rapid industrialization and sustainable technological development of any nation. Technical education has been an integral part of national development in many societies because of its impact on productivity and economic…

  18. Socio-technical considerations in epilepsy electronic patient record implementation.

    LENUS (Irish Health Repository)

    Mc Quaid, Louise

    2010-05-01

    Examination of electronic patient record (EPR) implementation at the socio-technical interface. This study was based on the introduction of an anti-epileptic drug (AED) management module of an EPR in an epilepsy out-patient clinic. The objective was to introduce the module to a live clinical setting within strictly controlled conditions to evaluate its usability and usefulness.

  19. Using Television Technology to Teach Technical Writing.

    Science.gov (United States)

    Wallisch, Bill

    Technical writing teachers at the U.S. Air Force Academy enhance student motivation by bringing real Air Force writing situations into the classroom through short videotapes which allow students to see how scientists and engineers cope with report writing in their daily work. Also, a special English honors course, which is part of the "Blue…

  20. Computerized creation of interactive electronic technical manuals (IETM)

    International Nuclear Information System (INIS)

    Galin, I.Yu.

    2011-01-01

    The author informs that the automated system of developing and maintaining the operational documentation (OD) (Technical Guide Builder) has been first developed and experimentally tested. The obtained result raises the competitiveness of Russian aircraft in international markets. The author offers methods and technology of OD formation, allowing to produce interactive OD for domestic aircraft industry, issued according to international standards in several languages [ru

  1. Technical descriptions of ten irrigation technologies for conserving energy

    Energy Technology Data Exchange (ETDEWEB)

    Harrer, B.J.; Wilfert, G.L.

    1983-05-01

    Technical description of ten technologies which were researched to save energy in irrigated agriculture are presented. These technologies are: well design and development ground water supply system optimization, column and pump redesign, variable-speed pumping, pipe network optimization, reduced-pressure center-pivot systems, low-energy precision application, automated gated-pipe system, computerized irrigation scheduling, and instrumented irrigation scheduling. (MHR)

  2. Predicting technology operational availability using technical maturity assessment

    International Nuclear Information System (INIS)

    Kenley, C.R.; Creque, T.R.

    1998-01-01

    A technical maturity assessment method was performed by systems engineers in collaboration with an advisory panel composed of team members from different Department of Energy sites and from different engineering and science disciplines. Various stabilization technologies were assessed annually as to their relative maturity and availability for use in stabilizing nuclear materials. After three years of assessments, several of the technologies are now components of operational systems. A regression analysis of the historical assessments was performed, and it was concluded that the numerical technical maturity score produced by a team of experts can provide a powerful predictor of the time remaining until the operational application of technologies

  3. Chemical Technology Division annual technical report 1989

    International Nuclear Information System (INIS)

    1990-03-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1989 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including high-performance batteries (mainly lithium/iron sulfide and sodium/metal chloride), aqueous batteries (lead-acid and nickel/iron), and advanced fuel cells with molten carbonate and solid oxide electrolytes: (2) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing 99 Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor (the Integral Fast Reactor), and waste management; and (5) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be administratively responsible for and the major user of the Analytical Chemistry Laboratory at Argonne National Laboratory (ANL)

  4. Chemical Technology Division. Annual technical report, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Laidler, J.J.; Myles, K.M.; Green, D.W.; McPheeters, C.C.

    1996-06-01

    Highlights of the Chemical Technology (CMT) Division`s activities during 1995 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (3) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (4) processes for separating and recovering selected elements from waste streams, concentrating low-level radioactive waste streams with advanced evaporator technology, and producing {sup 99}Mo from low-enriched uranium; (5) electrometallurgical treatment of different types of spent nuclear fuel in storage at Department of Energy sites; and (6) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems.

  5. Chemical Technology Division. Annual technical report, 1995

    International Nuclear Information System (INIS)

    Laidler, J.J.; Myles, K.M.; Green, D.W.; McPheeters, C.C.

    1996-06-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1995 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) methods for treatment of hazardous waste and mixed hazardous/radioactive waste; (3) the reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; (4) processes for separating and recovering selected elements from waste streams, concentrating low-level radioactive waste streams with advanced evaporator technology, and producing 99 Mo from low-enriched uranium; (5) electrometallurgical treatment of different types of spent nuclear fuel in storage at Department of Energy sites; and (6) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems

  6. Teaching Power Electronics with a Design-Oriented, Project-Based Learning Method at the Technical University of Denmark

    Science.gov (United States)

    Zhang, Zhe; Hansen, Claus Thorp; Andersen, Michael A. E.

    2016-01-01

    Power electronics is a fast-developing technology within the electrical engineering field. This paper presents the results and experiences gained from applying design-oriented project-based learning to switch-mode power supply design in a power electronics course at the Technical University of Denmark (DTU). Project-based learning (PBL) is known…

  7. Technical Integration of Nuclear Hydrogen Production Technology

    International Nuclear Information System (INIS)

    Lee, Ki Young; Chang, J. H.; Park, J. K.

    2007-06-01

    These works focus on the development of attainment indices for nuclear hydrogen key technologies, the analysis of the hydrogen production process and the performance estimation for hydrogen production system, and the assessment of the nuclear hydrogen production economy. To estimate the attainments of the key technologies in progress with the performance goals of GIF, itemized are the attainment indices based on SRP published in VHTR R and D steering committee of Gen-IV. For assessing the degree of attainments in comparison with the final goals of VHTR technologies in progress of researches, subdivided are the prerequisite items conformed to the NHDD concepts established in a preconceptual design in 2005. The codes for analyzing the hydrogen production economy are developed for calculating the unit production cost of nuclear hydrogen. We developed basic R and D quality management methodology to meet design technology of VHTR's needs. By putting it in practice, we derived some problems and solutions. We distributed R and D QAP and Q and D QAM to each teams and these are in operation. Computer simulations are performed for estimating the thermal efficiency for the electrodialysis component likely to adapting as one of the hydrogen production system in Korea and EED-SI process known as the key components of the hydrogen production systems. Using the commercial codes, the process diagrams and the spread-sheets were produced for the Bunsen reaction process, Sulphuric Acid dissolution process and HI dissolution process, respectively, which are the key components composing of the SI process

  8. CERN Technical Training 2005 - ELEC-2005: Electronics in High Energy Physics

    CERN Multimedia

    Monique Duval

    2004-01-01

    Learning for the LHC!ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the successful ELEC-2002 course series. This comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments.ELEC-2005 is composed of four Terms that will run throughout the year:Winter Term: Introduction to electronics in HEP (January-February, 6 lectures) Spring Term: Integrated circuits and VLSI technology for physics (March, 6 lectures) Summer Term: System electronics for physics: Issues (May, 7 lectures) Winter Term: Electronics applications in HEP experiments (November-December, 10 lectures) Lectures within each Term will take place on Tuesdays and Thursd...

  9. Technical Training: ELEC-2005 - Electronics in High Energy Physics: Summer Term (May 2005)

    CERN Multimedia

    Monique Duval

    2005-01-01

    ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the successful ELEC-2002 course series. This comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms. The Winter (Introduction to electronics in HEP) and Spring (Integrated circuits and VLSI technology for physics) Terms already took place; the next two Terms will run with the following schedule: Summer Term: System electronics for physics: Issues (May, 7 lectures) - now open for registration Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) Lectures within each Term will take place on Tuesday...

  10. Chemical Technology Division annual technical report 1989

    Energy Technology Data Exchange (ETDEWEB)

    1990-03-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1989 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including high-performance batteries (mainly lithium/iron sulfide and sodium/metal chloride), aqueous batteries (lead-acid and nickel/iron), and advanced fuel cells with molten carbonate and solid oxide electrolytes: (2) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamics plants and the technology for fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) nuclear technology related to a process for separating and recovering transuranic elements from nuclear waste and for producing {sup 99}Mo from low-enriched uranium targets, the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor (the Integral Fast Reactor), and waste management; and (5) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Division continued to be administratively responsible for and the major user of the Analytical Chemistry Laboratory at Argonne National Laboratory (ANL).

  11. Gigabit network technology. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Davenport, C.M.C. [ed.

    1996-10-01

    Current digital networks are evolving toward distributed multimedia with a wide variety of applications with individual data rates ranging from kb/sec to tens and hundreds of Mb/sec. Link speed requirements are pushing into the Gb/sec range and beyond the envelop of electronic networking capabilities. There is a vast amount of untapped bandwidth available in the low-attenuation communication bands of an optical fiber. The capacity in one fiber thread is enough to carry more than two thousand times as much information as all the current radio and microwave frequencies. And while fiber optics has replaced copper wire as the transmission medium of choice, the communication capacity of conventional fiber optic networks is ultimately limited by electronic processing speeds.

  12. Chemical Technology Division annual technical report 1984

    International Nuclear Information System (INIS)

    1985-02-01

    In this period, CMT conducted research and development in the following areas: (1) advanced batteries - mainly lithium alloy/metal sulfide and sodium/sulfur for electric vehicles; (2) aqueous batteries - mainly improved lead-acid and nickel/iron for electric vehicles; (3) advanced fuel cells with molten carbonate or solid oxide electrolytes; (4) coal utilization, including the heat and seed recovery technology for coal-fired magnetohydrodynamic plants and the technology for pressurized fluidized-bed combustors; (5) methodologies for recovery of energy from municipal waste; (6) solid and liquid desiccants that allow moisture to be removed with a minium of energy; (7) nuclear technology related to waste management, proof of breeding for a light water reactor, and the recovery processes for discharged fuel and the uranium blanket in a sodium-cooled fast reactor; and (8) physical chemistry of selected materials in environments simulating those of fission, fusion, and other energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting abundant raw materials to desired products; materials chemistry of liquids and vapors at high temperatures; interfacial processes of importance to corrosion science, surface science, and catalysis; atmospheric chemistry, most notably SO 2 oxidation mechanisms; and the thermochemistry of zeolites, related silicates, and inorganic compounds

  13. Chemical Technology Division annual technical report, 2001

    International Nuclear Information System (INIS)

    Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

    2002-01-01

    The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature superconductors

  14. Technical and economic assessment of energy conversion technologies for MSW

    Energy Technology Data Exchange (ETDEWEB)

    Livingston, W.R.

    2002-07-01

    Thermal processes for municipal solid wastes (MSW) based on pyrolysis and/or gasification that have relevance to the emerging UK market are described in this report, and the results of the technical and economical assessment of these processes are presented. The Mitsui R21 Technology, the Thermoselect Process, the Nippon Steel Waste Melting Process, the Pyropleq Process, and the Compact Power Process are selected for detailed comparison on the basis of the overall technical concept, the energy balance and the requirements for consumables, environmental performance, and the technical and commercial status of the technology. Details are also given of a comparison of the novel thermal technologies with conventional mass burn incineration for MSW.

  15. Technical and economic assessment of energy conversion technologies for MSW

    International Nuclear Information System (INIS)

    Livingston, W.R.

    2002-01-01

    Thermal processes for municipal solid wastes (MSW) based on pyrolysis and/or gasification that have relevance to the emerging UK market are described in this report, and the results of the technical and economical assessment of these processes are presented. The Mitsui R21 Technology, the Thermoselect Process, the Nippon Steel Waste Melting Process, the Pyropleq Process, and the Compact Power Process are selected for detailed comparison on the basis of the overall technical concept, the energy balance and the requirements for consumables, environmental performance, and the technical and commercial status of the technology. Details are also given of a comparison of the novel thermal technologies with conventional mass burn incineration for MSW

  16. Chemical Technology Division annual technical report, 1990

    International Nuclear Information System (INIS)

    1991-05-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1990 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for coal- fired magnetohydrodynamics and fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for a high-level waste repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, concentrating plutonium solids in pyrochemical residues by aqueous biphase extraction, and treating natural and process waters contaminated by volatile organic compounds; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the scientific and engineering programs at Argonne National Laboratory (ANL). 66 refs., 69 figs., 6 tabs

  17. Chemical Technology Division annual technical report, 1990

    Energy Technology Data Exchange (ETDEWEB)

    1991-05-01

    Highlights of the Chemical Technology (CMT) Division's activities during 1990 are presented. In this period, CMT conducted research and development in the following areas: (1) electrochemical technology, including advanced batteries and fuel cells; (2) technology for coal- fired magnetohydrodynamics and fluidized-bed combustion; (3) methods for recovery of energy from municipal waste and techniques for treatment of hazardous organic waste; (4) the reaction of nuclear waste glass and spent fuel under conditions expected for a high-level waste repository; (5) processes for separating and recovering transuranic elements from nuclear waste streams, concentrating plutonium solids in pyrochemical residues by aqueous biphase extraction, and treating natural and process waters contaminated by volatile organic compounds; (6) recovery processes for discharged fuel and the uranium blanket in the Integral Fast Reactor (IFR); (7) processes for removal of actinides in spent fuel from commercial water-cooled nuclear reactors and burnup in IFRs; and (8) physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also has a program in basic chemistry research in the areas of fluid catalysis for converting small molecules to desired products; materials chemistry for superconducting oxides and associated and ordered solutions at high temperatures; interfacial processes of importance to corrosion science, high-temperature superconductivity, and catalysis; and the geochemical processes responsible for trace-element migration within the earth's crust. The Analytical Chemistry Laboratory in CMT provides a broad range of analytical chemistry support services to the scientific and engineering programs at Argonne National Laboratory (ANL). 66 refs., 69 figs., 6 tabs.

  18. Chemical Technology Division annual technical report, 2001

    International Nuclear Information System (INIS)

    Lewis, D.; Gay, E. C.; Miller, J. C.; Boparai, A. S.

    2002-01-01

    The Chemical Technology Division (CMT) is one of eight engineering research divisions within Argonne National Laboratory, one of the U.S. government's oldest and largest research laboratories. The University of Chicago oversees the laboratory on behalf of the U.S. Department of Energy (DOE). Argonne's mission is to conduct basic scientific research, to operate national scientific facilities, to enhance the nation's energy resources, and to develop better ways to manage environmental problems. Argonne has the further responsibility of strengthening the nation's technology base by developing innovative technology and transferring it to industry. CMT is a diverse early-stage engineering organization, specializing in the treatment of spent nuclear fuel, development of advanced electrochemical power sources, and management of both high- and low-level nuclear wastes. Although this work is often indistinguishable from basic research, our efforts are directed toward the practical devices and processes that are covered by Argonne's mission. Additionally, the Division operates the Analytical Chemistry Laboratory and Environment, Safety, and Health Analytical Chemistry services, which provide a broad range of analytical services to Argonne and other organizations. The Division is multidisciplinary. Its people have formal training as ceramists; physicists; material scientists; electrical, mechanical, chemical, and nuclear engineers; and chemists. They have experience working in academia; urban planning; and the petroleum, aluminum, and automotive industries. Their skills include catalysis, ceramics, electrochemistry, metallurgy, nuclear magnetic resonance spectroscopy, and petroleum refining, as well as the development of nuclear waste forms, batteries, and high-temperature super-conductors. The Division's wide-ranging expertise finds ready application in solving energy and environmental problems. Division personnel are frequently called on by governmental and industrial

  19. Polymer electronics a flexible technology

    CERN Document Server

    Technology, Rapra

    2009-01-01

    The worldwide market for polymer electronic products has been estimated to be worth up to £15 billion by 2015 and the opportunity for new markets could be as high as £125 billion by 2025.'The rapid development of polymer electronics has revealed the possibility for transforming the electronics market by offering lighter, flexible and more cost effective alternatives to conventional materials and products. With applications ranging from printed, flexible conductors and novel semiconductor components to intelligent labels and large area displays and solar panels, products that were previously un

  20. Plasma Wave Electronic Terahertz Technology

    National Research Council Canada - National Science Library

    Shur, Michael

    2003-01-01

    Plasma waves are oscillations of electron density in time and space. In deep submicron field effect transistors plasma wave frequencies lie in the terahertz range and can be tuned by applied gate bias...

  1. Chemical Technology Division annual technical report, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

    1994-04-01

    Chemical Technology (CMT) Division this period, conducted research and development in the following areas: advanced batteries and fuel cells; fluidized-bed combustion and coal-fired magnetohydrodynamics; treatment of hazardous waste and mixed hazardous/radioactive waste; reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; separating and recovering transuranic elements, concentrating radioactive waste streams with advanced evaporators, and producing {sup 99}Mo from low-enriched uranium; recovering actinide from IFR core and blanket fuel in removing fission products from recycled fuel, and disposing removal of actinides in spent fuel from commercial water-cooled nuclear reactors; and physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, thin-film diamond surfaces, effluents from wood combustion, and molten silicates; and the geochemical processes involved in water-rock interactions. The Analytical Chemistry Laboratory in CMT also provides a broad range of analytical chemistry support.

  2. Chemical Technology Division annual technical report, 1993

    International Nuclear Information System (INIS)

    Battles, J.E.; Myles, K.M.; Laidler, J.J.; Green, D.W.

    1994-04-01

    Chemical Technology (CMT) Division this period, conducted research and development in the following areas: advanced batteries and fuel cells; fluidized-bed combustion and coal-fired magnetohydrodynamics; treatment of hazardous waste and mixed hazardous/radioactive waste; reaction of nuclear waste glass and spent fuel under conditions expected for an unsaturated repository; separating and recovering transuranic elements, concentrating radioactive waste streams with advanced evaporators, and producing 99 Mo from low-enriched uranium; recovering actinide from IFR core and blanket fuel in removing fission products from recycled fuel, and disposing removal of actinides in spent fuel from commercial water-cooled nuclear reactors; and physical chemistry of selected materials in environments simulating those of fission and fusion energy systems. The Division also conducts basic research in catalytic chemistry associated with molecular energy resources and novel ceramic precursors; materials chemistry of superconducting oxides, electrified metal/solution interfaces, molecular sieve structures, thin-film diamond surfaces, effluents from wood combustion, and molten silicates; and the geochemical processes involved in water-rock interactions. The Analytical Chemistry Laboratory in CMT also provides a broad range of analytical chemistry support

  3. ESDRED Temporary Sealing Technology Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, J.; Garcia-Sineriz, J. L.; Barcena, I.; Alonso, M. C.; Fernandez Luco, L.; Garcia, J. L.; Fries, T.; Pettersson, S.; Boden, A.; Salo, J. P.

    2009-07-01

    The work in the ESDRED In te grated Project Module 4, Temporary Sealing (using low pH cement) Technology, consisted first of designing a low pH cement formulation and then of preparing several concrete designs suitable for the construction of sealing plugs and for rock support using shot crete techniques. Regarding sealing plugs, a short plug was constructed at Aspo in Sweden and it was very quickly loaded to failure i.e. slippage by applying water pressure to one face. A second, full scale plug was subsequently constructed at Grimsel test site in Switzerland. It was loaded using the swelling pressure created by bentonite blocks which were artificially hydrated. At time of writing the targeted pressure on the plug was not reached. As the saturation of the bentonite is taking longer than expected the partners involved agreed to continue with the saturation of the bentonite blocks and the related data monitoring beyond the ESDRED Project. The studies on low-pH shot crete for rock sup port were based on available recipes of low-pH concrete mixtures for use in a repository. Pilot and full scale tests were carried out in Sweden and in Switzerland. (Author) 5 refs.

  4. Trust in technology a socio-technical perspective

    CERN Document Server

    Clarke, Karen; Rouncefield, Mark

    2006-01-01

    Encapsulates work done in the DIRC project (Interdisciplinary Research Collaboration in Dependability), bringing together a range of disciplinary approaches - computer science, sociology and software engineering - to produce a socio-technical systems perspective on the issues surrounding trust in technology in complex settings.

  5. Massachusetts Institute of Technology, Plasma Fusion Center, Technical Research Programs

    International Nuclear Information System (INIS)

    1980-08-01

    A review is given of the technical programs carried out by the Plasma Fusion Center. The major divisions of work areas are applied plasma research, confinement experiments, fusion technology and engineering, and fusion systems. Some objectives and results of each program are described

  6. Massachusetts Institute of Technology, Plasma Fusion Center, Technical Research Programs

    Energy Technology Data Exchange (ETDEWEB)

    Davidson, Ronald C.

    1980-08-01

    A review is given of the technical programs carried out by the Plasma Fusion Center. The major divisions of work areas are applied plasma research, confinement experiments, fusion technology and engineering, and fusion systems. Some objectives and results of each program are described. (MOW)

  7. Technology scan for electronic toll collection.

    Science.gov (United States)

    2008-06-01

    The purpose of this project was to identify and assess available technologies and methodologies for electronic toll collection (ETC) and to develop recommendations for the best way(s) to implement toll collection in the Louisville metropolitan area. ...

  8. Technical and Social Environments of Electronic Publishing in Japan.

    Science.gov (United States)

    Nakamoto, Hideshiro

    1988-01-01

    Discusses the feasibility of introducing electronic publishing into traditional Japanese markets within the context of recent progress in other technologies and mass communications in that country. It is suggested that the content and quality of publications, rather than the media by which they are presented, will determine the acceptance of…

  9. Industrial applications of electron beam technology

    International Nuclear Information System (INIS)

    Khairul Zaman Mohd Dahlan

    1997-01-01

    Electron beam technology was first introduced in Malaysia in 1989 with the conclusion of the bilateral cooperation between the Malaysian Institute for Nuclear Technology Research (MINT) and Japan International Co-operation Agency (JICA) on Radiation Application Projects. Two electron beam accelerators with energy of 3.0 MeV and 200 keV were installed at MINT. These two accelerators pave the way for R and D to be carried out in radiation processing of polymers for cross-linking and surface curing. In 1994, another electron beam accelerator was installed in the private sector for cross-linking of home appliance wires. Since then, two more accelerators were installed in the private sector for cross-linking of heat shrinkable plastic films. Recently, a local company has acquired a low energy electron beam machine for cross-linking of plastic film. Within a period of 7 years, industrial applications of electron beam technology in Malaysia have increased significantly

  10. Electronic Scholarly Journals: A Review of Technical Issues in Digital Environment

    Directory of Open Access Journals (Sweden)

    Golnessa Galyani Moghaddam

    2006-12-01

    Full Text Available Scholarly journals are known as the most important medium for scholarly communication since long time back. As technology transforms the flow of information and idea everywhere, it changes the nature of scholarly communications and publishing of scholarly journals as well. The electronic scholarly publishing rapidly produced an expectation, among researchers of the availability of articles at their desktop, rather than the previous scenario of visiting the library to read a print journal issue. There are lots of technological improvements in electronic journals publishing. The present paper looks at some of technical issues in electronic publishing such as DOI, DOI-X, CrossRef, Citation/Reference Linking, OpenURL, SFX and MetaLib which are being used in the World Wide Web.

  11. Nanofabrication Technology for Production of Quantum Nano-Electronic Devices Integrating Niobium Electrodes and Optically Transparent Gates

    Science.gov (United States)

    2018-01-01

    TECHNICAL REPORT 3086 January 2018 Nanofabrication Technology for Production of Quantum Nano-electronic Devices Integrating Niobium Electrodes...work described in this report was performed for the by the Advanced Concepts and Applied Research Branch (Code 71730) and the Science and Technology ...Applied Sciences Division iii EXECUTIVE SUMMARY This technical report demonstrates nanofabrication technology for Niobium heterostructures and

  12. Electronic Nose Technology and its Applications

    Directory of Open Access Journals (Sweden)

    Esmaeil MAHMOUDI

    2009-08-01

    Full Text Available In the past decade, Electronic Nose instrumentation has generated much interest internationally for its potential to solve a wide variety of problems in fragrance and cosmetics production, food and beverages manufacturing, chemical engineering, environmental monitoring and more recently medical diagnostic, bioprocesses and clinical diagnostic plant diseases. This instrument measure electrical resistance changes generated by adsorption of volatiles to the surface of electro active- polymer coated sensor- unique digital electronic fingerprint of aroma derived from multi-sensor- responses to distinct mixture of microbial volatiles. Major advances in information and gas sensor technology could enhance the diagnostic power of future bio-electronic nose and facilitate global surveillance mode of disease control and management. Several dozen companies are now designed and selling electronic nose units globally for a wide variety of expending markets. The present review includes principles of electronic nose technology, biosensor structure and applications of electronic nose in many fields.

  13. Technical requirement of experiments and facilities for fusion nuclear technology

    International Nuclear Information System (INIS)

    Abdou, M.; Tillak, M.; Gierszwski, P.; Grover, J.; Puigh, R.; Sze, D.K.; Berwald, D.

    1986-06-01

    The technical issues and requirements of experiments and facilities for fusion nuclear technology (FNT) have been investigated. The nuclear subsystems addressed are: a) blanket, b) radiation shield, c) tritium processing system, and d) plasma interactive components. Emphasis has been placed on the important and complex development problems of the blanket. A technical planning process for FNT has been developed and applied, including four major elements: 1) characterization of issues, 2) quantification of testing requirements, 3) evaluation of facilities, and 4) development of a test plan to identify the role, timing, characteristics and costs of major experiments and facilities

  14. Signal processing and electronics for nuclear spectrometry. Proceedings of a technical meeting

    International Nuclear Information System (INIS)

    2009-12-01

    The IAEA has responded to Member States needs by implementing programmatic activities that provide interested Member States, particularly those in developing countries, with support to increase, and in some cases establish national and regional capabilities for the proper operation, calibration, maintenance and utilization of instruments in nuclear spectrometry applications. Technological advances in instrumentation, as well as the consequent high rate of obsolescence, make it important for nuclear instrumentation laboratories in Member States to keep their knowledge and skills up to date. This publication reviews the current status, developments and trends in electronics and digital methods for nuclear spectrometry, providing useful information for interested Member States to keep pace with new and evolving technologies. All nuclear spectrometry systems contain electronic circuits and devices, commonly referred to as front-end electronics, which accept and process the electrical signals produced by radiation detectors. This front-end electronics are composed of a chain of signal processing subsystems that filter, amplify, shape, and digitise these electrical signals to finally produce digitally encoded information about the type and nature of the radiation that stimulated the radiation detector. The design objective of front-end electronics is to obtain maximum information about the radiation and with the highest possible accuracy. Historically, the front-end electronics has consisted of all analog components. The performance delivered has increased continually over time through the development and implementation of new and improved analog electronics and electronic designs. The development of digital electronics, programmable logic, and digital signal processing techniques has now enabled most of the analog front-end electronics to be replaced by digital electronics, opening up new opportunities and delivering new benefits not previously achievable. Digital

  15. ADVANCED TECHNOLOGIES OF ELECTRONIC EDUCATIONAL SYSTEMS DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    M. Shishkina

    2011-11-01

    Full Text Available Actual problems and contradictions of electronic educational systems development are described: availability of education, quality of educational services; individualization of education; exposures and advantages in using of computer technology; standardization of technologies and resources. Tendencies of their solution in the view of development of new advanced technologies of e-education are specified. The essence and advantages of using the cloud computing technologies as a new platform of distributed learning are specified. Advanced directions of cloud-based data usage in executive system of education are declared: access management, content management, asset management, communications management.

  16. Plasma technology: a technical economical and political challenge

    International Nuclear Information System (INIS)

    Abreu, V.A. de; Vicente, L.C.; Bender, O.W.; Sanches Junior, O.

    1987-01-01

    To survey the State of the Art and Technic in Material, Process and Products by Plasma, it was needed to assemble economic, political and managerial variables that will affect the absortion and implantation of this technology in Brazil. Through a survey in industries, universities, research centers, energy agencies and financial and forster institutions it was possible to build a frame that gave us conditions to forecasting and suggest some mesures to Plasma sector. (author) [pt

  17. THE PROFESSIONAL QUALIFICATION SOLIDARY EXTENSION PROJECT AT ELECTRONICS: TECHNICAL AUXILIAR

    Directory of Open Access Journals (Sweden)

    Glaucio Lopes Ramos

    2009-10-01

    Full Text Available This paper has the objective to present the extension course “professional qualification solidary extension project at electronics: technical auxiliar” in the Electrical Engineering course in the University Center of Belo Horizonte, as a professional qualification activity that make possible to young, adults and elderly people from poor communities the social inclusion and an opportunity to improve their access to the labor market. The course is part of extension program of Uni-BH, UniTrabalho e Renda, that is offered since 2006. The responsible for the course are professors and students of the Electrical Engineering course, and an electricity project is also offered. This paper presents the results of an evaluation that is made for the students at the beginning and at the end of the course and showed that the concepts had been assimilated by the students and the expectation of them related to the insertion at labor market is also improved.

  18. 76 FR 66311 - Draft Documents To Support Submission of an Electronic Common Technical Document; Availability

    Science.gov (United States)

    2011-10-26

    ...] Draft Documents To Support Submission of an Electronic Common Technical Document; Availability AGENCY... making regulatory submissions in electronic format using the electronic Common Technical Document (eCTD....S. regional document type definition, version 3.0) and ``Comprehensive Table of Contents Headings...

  19. Applications and technology of electron beam accelerators

    International Nuclear Information System (INIS)

    Sethi, R.C.

    2005-01-01

    Traditionally, accelerators have been employed for pursuing research in basic sciences. But over the last couple of decades their uses have proliferated into the applied fields as well. The major credit for which goes to the electron beams. Electron beams or the radiations generated by them are being extensively used in almost all the applied areas. This article is a brief account of the impact made by the accelerator based electron beams and the attempts initiated by DAE for building a base in this technology. (author)

  20. NASA Technical Interchange Meeting (TIM): Advanced Technology Lifecycle Analysis System (ATLAS) Technology Tool Box

    Science.gov (United States)

    ONeil, D. A.; Craig, D. A.; Christensen, C. B.; Gresham, E. C.

    2005-01-01

    The objective of this Technical Interchange Meeting was to increase the quantity and quality of technical, cost, and programmatic data used to model the impact of investing in different technologies. The focus of this meeting was the Technology Tool Box (TTB), a database of performance, operations, and programmatic parameters provided by technologists and used by systems engineers. The TTB is the data repository used by a system of models known as the Advanced Technology Lifecycle Analysis System (ATLAS). This report describes the result of the November meeting, and also provides background information on ATLAS and the TTB.

  1. Linac technology for free-electron lasers

    International Nuclear Information System (INIS)

    Cooper, R.K.; Morton, P.L.; Wilson, P.B.; Keefe, D.; Faltens, A.

    1983-01-01

    The purpose of this paper is to concentrate on the properties of high-energy electron linear accelerators for use in free-electron lasers operating principally in the Compton regime. To fix our focus somewhat, we shall consider electron energies in the 20- to 200-MeV range and consider requirements for high-power free-electron lasers operating in the 0.5- to 10-μm range. Preliminary remarks are made on high-power free-electron laser amplifiers and oscillators and some desirable characteristics of the linacs that deliver electron beams for these devices. Both the high peak-current requirements of the amplifier and the high pulse-repetition frequency requirements of the oscillator can be met by present-day linac technology, although not necessarily by the same machine. In this papers second and third section, the technology of two rather different types of linear accelerators, the rf linac and the induction linac, is reviewed. In conclusion, applications to the Free Electron Lasers are stated

  2. Technology and applications of electron accelerator

    International Nuclear Information System (INIS)

    Natsir, M.

    1998-01-01

    Technology of electron accelerator have been developed so fast in advanced countries. It was applied in the research and development (R and D) and comercially in various industries. The industries applying electron accelerator includes polymers industry, sterilization of medical tools, material surface modification, and environmental management. The radiation process using electron beam is an ionization radiation process. Two facilities of electron accelerator have been established in pilot scale at the Centre for the Application of Isotope and Radiation CAIR-BATAN, Jakarta, for the RandD of radiation process technology and in demonstrating the electron accelerator application in industry in Indonesia. The first has low energy specification of 300 keV, 50 mA, EPS-300 type and the second has medium energy specification of 2 MeV, 10 mA dynamitron model GJ-2 type. Both the electron accelerators have an electron penetration depth capability of 0.6 and 12 mm, respectively, for the double side irradiation in the materials with density of 1 g/cm 3 . They also highly capacity production and electron beam cross-section of 120 cm length and 10 cm width. The beam will go through the atmosphere for irradiation samples or industrial products. The radiation dose can be selected precisely by adjusting the electron beam current and conveyor speed. Both of these facilities were applied in many aspects RandD, for examples dosimetry, wood surface coating, cross-linking of polymer, heatshrincable tube, polymer grafting, plastic degradation, food preservation, sterilization and so on. Engineering factors of radiation design process and general observation of electron accelerator application in RandD for various industries in Indonesia are briefly discussed

  3. Technology and Power. A Foucauldian Analysis of Electronic Monitoring Discourses

    Directory of Open Access Journals (Sweden)

    Anna Vitores

    2007-05-01

    Full Text Available The article aims to show the importance of FOUCAULT within social studies of science and technology. It also illustrates how a Foucauldian analysis can be useful for studies of science, technology and society focused on power effects. To accomplish these objectives we analyze the emergence of a specific techno-scientific innovation: the electronic monitoring of offenders. We map the discontinuities and discourse dispersions linked to those practices that constitute different materializations of this electronic device. Because we start from questions concerning power technologies, rather than simply analyzing the ideologies and knowledges that legitimate electronic monitoring and its technical reliability, we attend to the assemblage of discourses, rhetorics, vocabularies, techniques and procedures by which knowledge is intertwined and joins with the exercise of power. In this way, we show how one of FOUCAULT's technologies of power—disciplinary technology—is articulated, nourished and contradicted by other emergent logics drawing on new forms of regulation and social control. URN: urn:nbn:de:0114-fqs070225

  4. Turning Technologies into Businesses- The Challenge for the Technical Entrepreneur

    Science.gov (United States)

    Glass, Alexander

    2000-03-01

    Over the past twenty-five years, new businesses based on innovative technology have been the driving force for the US economy. Due to the abundance of early-stage capital, each year, thousands of scientists and engineers receive support to start new, technology-based businesses. However, the transition from technologist to entrepreneur is often difficult. It requires a shift in emphasis from a technology focus to a market focus. We shall discuss the challenges facing the technical entrepreneur in launching a new enterprise, and a variety of resources that are available to help the entrepreneur succeed. Many technologists fall victim to the myth that if you ``build a better mousetrap, the world will beat a path to your door." To be sure, it is important to base your business on sound technology that offers a clear advantage over current practice, and, if possible, to secure title to the technology, either by obtaining patent protection, or securing an exclusive license. Once that is done, however, the principal concern of the fledgling enterprise is building a business and obtaining the financial resources to enable it to grow. The entrepreneur must develop a clear and compelling business model, that can be communicated to a non-technical investor in a few minutes. This requires a mode of thinking and expression quite different from that commonly used in engineering or scientific discussions. Fortunately, abundant resources are available to help the technologist become a successful entrepreneur. We shall discuss the kinds of assistance that are generally available through local and national programs, and give specific examples based on the activities of the Bay Area Regional Technology Alliance in northern California.

  5. 1998 Chemical Technology Division Annual Technical Report. Applying chemical innovation to environmental problems

    International Nuclear Information System (INIS)

    Ackerman, J.P.; Einziger, R.E.; Gay, E.C.; Green, D.W.; Miller, J.F.

    1999-01-01

    The Chemical Technology (CMT) Division is a diverse technical organization with principal emphases in environmental management and development of advanced energy sources. The Division conducts research and development in three general areas: (1) development of advanced power sources for stationary and transportation applications and for consumer electronics, (2) management of high-level and low-level nuclear wastes and hazardous wastes, and (3) electrometallurgical treatment of spent nuclear fuel. The Division also performs basic research in catalytic chemistry involving molecular energy resources, mechanisms of ion transport in lithium battery electrolytes, and the chemistry of technology-relevant materials. In addition, the Division operates the Analytical Chemistry Laboratory, which conducts research in analytical chemistry and provides analytical services for programs at Argonne National Laboratory (ANL) and other organizations. Technical highlights of the Division's activities during 1998 are presented

  6. Technical feasibility for electron beam application on maize seeds disinfection for maize cultivation in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Zago, Claudia [Proenco Brasil Ltda. (Brazil)]. E-mail: clauzago@uol.com.br; Rela, Paulo Roberto [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (brazil). Centro de Tecnologia das Radiacoes]. E-mail: prela@ipen.br

    2007-07-01

    Among the man made activities agriculture plays a fundamental rule on the interference with environment; new alternatives for clean technologies are being searched in order to reduce the impact and degradation of the environment. This work presents a feasibility study to implement in Brazil a technology using electron beam treatment to disinfect maize seeds avoiding the spoilage from pathogens microorganisms. This technology was developed in Germany by Fraunhofer Institut FEP (Dresden) and the private company Schmidt-Seeger AG. It was patented as 'e-ventus'. Concerning to the technical feasibility it shows to be quite useful due to the results of the experiments performed in other countries with maize seeds and properly for the large amount to be treated in the country. Under the environmental management it is quite advantageous when compared with the traditional technology that uses chemical seed dressing agents. Nevertheless for a large scale commercial application it is necessary a cost analyse comparison study between the traditional technology and the alternative using electron beam. (author)

  7. Technical feasibility for electron beam application on maize seeds disinfection for maize cultivation in Brazil

    International Nuclear Information System (INIS)

    Zago, Claudia; Rela, Paulo Roberto

    2007-01-01

    Among the man made activities agriculture plays a fundamental rule on the interference with environment; new alternatives for clean technologies are being searched in order to reduce the impact and degradation of the environment. This work presents a feasibility study to implement in Brazil a technology using electron beam treatment to disinfect maize seeds avoiding the spoilage from pathogens microorganisms. This technology was developed in Germany by Fraunhofer Institut FEP (Dresden) and the private company Schmidt-Seeger AG. It was patented as 'e-ventus'. Concerning to the technical feasibility it shows to be quite useful due to the results of the experiments performed in other countries with maize seeds and properly for the large amount to be treated in the country. Under the environmental management it is quite advantageous when compared with the traditional technology that uses chemical seed dressing agents. Nevertheless for a large scale commercial application it is necessary a cost analyse comparison study between the traditional technology and the alternative using electron beam. (author)

  8. Assessment of material and technical resources of crop production technologies

    Directory of Open Access Journals (Sweden)

    V. M. Beylis

    2017-01-01

    Full Text Available The author explains the general principles of influence of the material and technical resources (MTR on performance and efficiency of the main technological operations in crop production. Various technologies from the point of view of MTR expenses were estimated. The general tendencies in development of crop production technologies were revealed. The distribution of costs of materials and equipment to perform a variety of agricultural activities was determined. Cost indicators should be a guide in the search of innovative technological processes and working elements of agricultural machins. The greatest values of expenses of work, fuel, metal, and also, money where found. The concepts allowing to provide costs production reduction were formulated. To achieve the maximum productivity with the minimum expenses, the perspective calculations shoul be based on «progressive» agrotechnologies. When determining progressive agrotechnology it is necessary on reasonable grounds to approach indicators of crop productivity in various agrozones and regions of the country. For an assessment of efficiency of MTR by crop production and ensuring decrease in resource intensity of agricultural products by search and use of essentially new technologies for energy saving when performing agricultural operations, an integrated percentage indicator of comparison of progressive technologies with the applied ones was developed. MTR at application of new progressive crop production technologies by integrated percentage index were estimated. This indicator can be used for definition of efficiency of MTR. Application of the offered technique will promote an effective assessment of MTR, decrease in resource intensity by search and developments of essentially new technologies of performance of operations in crop production.

  9. Electron gun for technological linear accelerator

    International Nuclear Information System (INIS)

    Khodak, I.V.; Kushnir, V.A.; Mirochenko, V.V.; Stepin, D.L.; Zavada, L.M.

    2000-01-01

    The work is purposed to the design of diode electron gun for powerful technologic electron linac and to experimental investigations of the beam parameters at the gun exit.The gun feature is the quick cathode replacement.This is very impotent for operating of the accelerator.The gun optics and beam parameters were calculated using the EGUN code.Beam parameters were investigated as at the special test stand so as component of the linac injector.The gun produces the beam current of 2 A at the anode voltage 25 kV.Measured beam parameters correspond to calculated results

  10. Organic electronics emerging concepts and technologies

    CERN Document Server

    Santato, Clara

    2013-01-01

    An overview of the tremendous potential of organic electronics, concentrating on those emerging topics and technologies that will form the focus of research over the next five to ten years. The young and energetic team of editors with an excellent research track record has brought together internationally renowned authors to review up-and-coming topics, some for the first time, such as organic spintronics, iontronics, light emitting transistors, organic sensors and advanced structural analysis. As a result, this book serves the needs of experienced researchers in organic electronics, graduate

  11. Electronic property measurements for piezoelectric ceramics. Technical notes

    International Nuclear Information System (INIS)

    Cain, M.; Stewart, M.; Gee, M.

    1998-01-01

    A series of measurement notes are presented, with emphasis placed on the technical nature of the testing methodology, for the determination of key electronic properties for piezoelectric ceramic materials that are used as sensors and actuators. The report is segmented into 'sections' that may be read independently from the rest of the report. The following measurement issues are discussed: Polarisation/Electric field (PE) loop measurements including a discussion of commercial and an in-house constructed system that measures PE loops; Dielectric measurements at low and high stress application, including some thermal and stress dependency modelling of piezo materials properties, developed at NPL; Strain measurement techniques developed at CMMT; Charge measurement techniques suitable for PE loop and other data acquisition; PE loop measurement and software analysis developed at CMMT and Manchester University. The primary objective of this report is to provide a framework on which the remainder of the testing procedures are to be developed for measurements of piezoelectric properties at high stress and stress rate. These procedures will be the subject of a future publication. (author)

  12. Control system by the technological electron Linac KUT-20

    CERN Document Server

    Akchurin, Y I; Gurin, V A; Demidov, N V

    2001-01-01

    The high-power technological electron linac KUT-20 was developed at the Science Research Complex 'Accelerator' of NSC KIPT. The linac consists of two 1.2 m length accelerating structures with a variable geometry and an injector. The latter comprises a diode electron gun,a klystron type buncher and an accelerating cavity.With a RF supply power at accelerating structure entries of 11 MW and with a current at the accelerator exit of 1A,the beam energy will be up to 20 MeV.An average beam power is planned to be 20 kW.All systems of the accelerator are controlled by a computerised control system. The program and technical complex consist of PC equipped with fast ADC control console, synchronization unit, microprocessor-operated complexes.

  13. Second NASA Technical Interchange Meeting (TIM): Advanced Technology Lifecycle Analysis System (ATLAS) Technology Tool Box (TTB)

    Science.gov (United States)

    ONeil, D. A.; Mankins, J. C.; Christensen, C. B.; Gresham, E. C.

    2005-01-01

    The Advanced Technology Lifecycle Analysis System (ATLAS), a spreadsheet analysis tool suite, applies parametric equations for sizing and lifecycle cost estimation. Performance, operation, and programmatic data used by the equations come from a Technology Tool Box (TTB) database. In this second TTB Technical Interchange Meeting (TIM), technologists, system model developers, and architecture analysts discussed methods for modeling technology decisions in spreadsheet models, identified specific technology parameters, and defined detailed development requirements. This Conference Publication captures the consensus of the discussions and provides narrative explanations of the tool suite, the database, and applications of ATLAS within NASA s changing environment.

  14. Electron Beam Technology for Environmental Pollution Control.

    Science.gov (United States)

    Chmielewski, Andrzej G; Han, Bumsoo

    2016-10-01

    Worldwide, there are over 1700 electron beam (EB) units in commercial use, providing an estimated added value to numerous products, amounting to 100 billion USD or more. High-current electron accelerators are used in diverse industries to enhance the physical and chemical properties of materials and to reduce undesirable contaminants such as pathogens, toxic byproducts, or emissions. Over the past few decades, EB technologies have been developed aimed at ensuring the safety of gaseous and liquid effluents discharged to the environment. It has been demonstrated that EB technologies for flue gas treatment (SO x and NO x removal), wastewater purification, and sludge hygienization can be effectively deployed to mitigate environmental degradation. Recently, extensive work has been carried out on the use of EB for environmental remediation, which also includes the removal of emerging contaminants such as VOCs, endocrine disrupting chemicals (EDCs), and potential EDCs.

  15. Electronics, information, Communication and high technology

    International Nuclear Information System (INIS)

    1999-11-01

    The contents of this book are summary of investigation, investigation system, purpose of investigation, characteristic of this investigation, important studying and development filed, compare of the level of research and development, policy, characteristic of the respondent, a future illustration in 2025 cause of hindrance of realization, propel method of research and development, the prediction of the realization period the result of investigation in electronics, information communication and high technology.

  16. The Intelligent Technologies of Electronic Information System

    Science.gov (United States)

    Li, Xianyu

    2017-08-01

    Based upon the synopsis of system intelligence and information services, this paper puts forward the attributes and the logic structure of information service, sets forth intelligent technology framework of electronic information system, and presents a series of measures, such as optimizing business information flow, advancing data decision capability, improving information fusion precision, strengthening deep learning application and enhancing prognostic and health management, and demonstrates system operation effectiveness. This will benefit the enhancement of system intelligence.

  17. Final Technical Report for Photovoltaic Power Electronics Research Initiative (PERI)

    Energy Technology Data Exchange (ETDEWEB)

    Amirahmadi, Ahmadreza [Univ. of Central Florida, Orlando, FL (United States); Jordan, Charlie [Univ. of Central Florida, Orlando, FL (United States); batarseh, Issa [Univ. of Central Florida, Orlando, FL (United States)

    2015-08-31

    The Power Electronics team at the University of Central Florida (UCF) has developed a novel three-phase micro-inverter for photovoltaic (PV) distributed applications. Based on a new advanced topology and control methodology, the developed inverter is small in size, and achieved DoE targeted power density, cost and efficiency specifications. Today’s inverters are widely used in PV based energy harvesting systems, but are based on single-phase design with limited application to large installations. These micro-inverters have been shown to have advantageous over their string inverter counterparts in both grid-tied PV energy harvesting and standalone micro-grid systems with energy storage. Some of these are simplified installation, no high voltage DC wiring, no single point of failure and improved energy harvesting. Several patents have been issued and this new solar conversion technology has been licensed to the private sector.

  18. 29 CFR 1615.135 - Electronic and information technology requirements.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 4 2010-07-01 2010-07-01 false Electronic and information technology requirements. 1615... INFORMATION TECHNOLOGY § 1615.135 Electronic and information technology requirements. (a) Development, procurement, maintenance, or use of electronic and information technology.—When developing, procuring...

  19. Ferroelectric Electron Emission Principles and Technology

    CERN Document Server

    Riege, H

    1997-01-01

    The spontaneous electrical polarization of ferroelectric materials can be changed either by reversal or by phase transition from a ferroelectric into a non-ferroelectric state or vice versa. If spontaneous polarization changes are induced with fast heat, mechanical pressure, laser or electric field pulses on a submicrosecond time scale, strong uncompensated surface charge densities and related polarization fields are generated, which may lead to the intense self-emission of electrons from the negatively charged free surface areas of the ferroelectric sample. Hence, electron guns can be built with extraction-field-free ferroelectric cathodes, which may be easily separated from the high-field regions of post-accelerating gap structures. The intensity, the energy, the temporal and spatial distribution, and the repetitition rate of the emitted electron beams can be controlled within wide limits via the excitation pulses and external focusing and accelerating electromagnetic fields. The technological advantages an...

  20. Vocational technical and adult education: Status, trends and issues related to electronic delivery

    Science.gov (United States)

    Rothenberg, D.

    1973-01-01

    Data are analyzed, and trends and issues are discussed to provide information useful to the systems designer who wishes to identify and assess the opportunities for large scale electronic delivery in vocational/technical and adult education. Issues connected with vocational/technical education are investigated, with emphasis on those issues in the current spotlight which are relevant to the possibilities of electronic delivery. The current role of media is examined in vocational/technical instruction.

  1. The Office of Technology Development technical reports. A bibliography

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    The US Department of Energy`s Office of Technology Development (OTD) within the Office of Environmental Management was established in 1989 to conduct an aggressive national program of applied research, development, demonstration, testing, and evaluation (RDDT&E) for innovative environmental cleanup solutions that are safer and more time- and cost-effective than those currently available. In many cases, the development of new technology presents the best hope for ensuring a substantive reduction in risk to the environment and improved worker/public safety within realistic financial constraints. Five major remediation and waste management problem areas have been identified to date within the DOE weapons complex; Contaminant Plume Containment and Remediation; Mixed Waste Characterization, Treatment, and Disposal; High-Level Waste Tank Remediation; Landfill Stabilization; and Facility Transitioning, Decommissioning, and Final Disposition. New technologies to address these problem areas are demonstrated to the point that they are proven to work and that they can be transferred to the private sector end-users. This bibliography contains information on scientific and technical reports sponsored by the Office of Environmental Management from its inception in 1989 through June 1994. Future issues contain reports from Technology Development activities and will be published biannually.

  2. 76 FR 35474 - UAW-Chrysler Technical Training Center, Technology Training Joint Programs Staff, Including On...

    Science.gov (United States)

    2011-06-17

    ...-Chrysler Technical Training Center, Technology Training Joint Programs Staff, Including On-Site Leased Workers From Cranks, O/E Learning, DBSI, IDEA, and Tonic/MVP, Detroit, MI; UAW-Chrysler Technical Training... workers and former workers of UAW-Chrysler Technical Training Center, Technology Training Joint Programs...

  3. Handbook of Machine Olfaction: Electronic Nose Technology

    Science.gov (United States)

    Pearce, Tim C.; Schiffman, Susan S.; Nagle, H. Troy; Gardner, Julian W.

    2003-02-01

    "Electronic noses" are instruments which mimic the sense of smell. Consisting of olfactory sensors and a suitable signal processing unit, they are able to detect and distinguish odors precisely and at low cost. This makes them very useful for a remarkable variety of applications in the food and pharmaceutical industry, in environmental control or clinical diagnostics and more. The scope covers biological and technical fundamentals and up-to-date research. Contributions by renowned international scientists as well as application-oriented news from successful "e-nose" manufacturers give a well-rounded account of the topic, and this coverage from R&D to applications makes this book a must-have read for e-nose researchers, designers and users alike.

  4. Evaluating the technical aspects of mixed waste treatment technologies

    International Nuclear Information System (INIS)

    Bagaasen, L.M.; Scott, P.A.

    1992-10-01

    This report discusses treatment of mixed wastes which is thought to be more complicated than treatment of either hazardous or radioactive wastes. In fact, the treatment itself is no more complicated: however, the regulations that define acceptability of the final waste disposal system are significantly more entangled, and sometimes in apparent conflict. This session explores the factors that influence the choice of waste treatment technologies, and expands on some of the limitations to their application. The objective of the presentation is to describe the technical factors that influence potential treatment processes and the ramifications associated with particular selections (for example, the generation of secondary waste streams). These collectively provide a framework for making informed treatment process selections

  5. TECHNOLOGICAL TOOLS: FROM TECHNICAL AFFORDANCES TO EDUCATIONAL AFFORDANCES

    Directory of Open Access Journals (Sweden)

    Nicos Valanides

    2018-04-01

    Full Text Available The integration of these tools in education and in authentic and effective learning/teaching environments has become an issue of great concern among educators, researchers and other related audiences. All emphasize the need to design and develop technology-enhanced curricula and teaching/learning environments (formal, non-formal and informal that are developmentally appropriate for young and/or older learners. The vision is to integrate the tools and their associated technical affordance in teaching/learning environments in such a way, so that all learners, irrespective of their cognitive differences and abilities, could increase their learning gains, and develop the abilities and skills that are needed for citizens of the 21st century.

  6. Technical workshop on safeguards, verification technologies, and other related experience

    International Nuclear Information System (INIS)

    1998-01-01

    The aim of the Technical Workshop on safeguards was to encourage a clearer understanding of the IAEA Safeguards System, its origins and evolution and the present state of the art. Presentations held by the IAEA officials and outside experts examined as well other components of the non-proliferation regime, the current practices and procedures, and the future prospects. A series of presentations described the characteristics of the interaction between global and regional verification systems and described relevant past and present experience. Prominence given to such state of the art verification technologies as environmental sampling, satellite imaging and monitoring thorough remote and unattended techniques demonstrated, beyond any doubt, the essentially dynamic nature of verification. It is generally acknowledged that there have been major achievements in preventing spread of nuclear weapons, but no verification system can in itself prevent proliferation

  7. Technical workshop on safeguards, verification technologies, and other related experience

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-31

    The aim of the Technical Workshop on safeguards was to encourage a clearer understanding of the IAEA Safeguards System, its origins and evolution and the present state of the art. Presentations held by the IAEA officials and outside experts examined as well other components of the non-proliferation regime, the current practices and procedures, and the future prospects. A series of presentations described the characteristics of the interaction between global and regional verification systems and described relevant past and present experience. Prominence given to such state of the art verification technologies as environmental sampling, satellite imaging and monitoring thorough remote and unattended techniques demonstrated, beyond any doubt, the essentially dynamic nature of verification. It is generally acknowledged that there have been major achievements in preventing spread of nuclear weapons, but no verification system can in itself prevent proliferation Refs, figs, tabs

  8. Electrical and electronic principles and technology

    CERN Document Server

    John Bird

    2013-01-01

    This much-loved textbook introduces electrical and electronic principles and technology to students who are new to the subject. Real-world situations and engineering examples put the theory into context. The inclusion of worked problems with solutions really help aid your understanding and further problems then allow you to test and confirm you have mastered each subject. In total the books contains 410 worked problems, 540 further problems, 340 multiple-choice questions, 455 short-answer questions, and 7 revision tests with answers online.This an ideal text for vocational courses enabling a s

  9. Research and Development Issues for Interactive Electronic Technical Manuals

    National Research Council Canada - National Science Library

    Ricci, Katrina

    2002-01-01

    .... While there is a wide range of research issues associated with technical manuals, the focus of the Intelligent Performance Support and Training effort is the development and evaluation of various...

  10. 48 CFR 1352.239-71 - Electronic and information technology.

    Science.gov (United States)

    2010-10-01

    ... Electronic and information technology. As prescribed in 48 CFR 1339.270(a), insert the following provision: Electronic and Information Technology (APR 2010) (a) To be considered eligible for award, offerors must propose electronic and information technology (EIT) that meet the applicable Access Board accessibility...

  11. Technical Features of the Architecture of an Electronic Trilingual Dictionary

    Directory of Open Access Journals (Sweden)

    Grygorii Chetverikov

    2016-12-01

    Full Text Available Technical Features of the Architecture of an Electronic Trilingual Dictionary This article is devoted to the development of the software system used to create an English-Russian-Ukrainian terminological dictionary. Scanned and recognized documents in MSWord format were the input data for the dictionary. Issues which appeared during the parsing of the input data are analyzed and solutions using regular expressions are identified. This article also describes the scheme of the dictionary’s lexicographical database, and its classes of models, views and view models. In addition, a detailed description of the software system from a user’s perspective is included, the prospects for the usage of the dictionary are discussed, and the methods used during the development of the system are described. The software system is built using the design pattern Model-View-View-Model. Through the use of this pattern, internal logic is separated from user interface, thus changes made in different parts of the software may be independent. The developed software system allows users to edit, to fill, and thus to create new thematic transferable electronic dictionaries. The main advantage of the system is the equality of languages, i.e. each user can decide which language is to be major.   Opracowanie oprogramowania trzyjęzycznego słownika elektronicznego Artykuł jest poświęcony opracowaniu oprogramowania rosyjsko-ukraińsko-angielskiego słownika terminologicznego. Za wejściowe dane autorzy przyjęli zeskanowane i rozpoznane dokumenty w formacie MSWord. Błędy powstałe w czasie analizy składniowej wejściowych danych zostały przeanalizowane, a autorzy wskazali drogę ich likwidacji za pomocą regularnych wyrażeń. W pracy została dokładnie opisana baza leksykograficzna danych słownika, zostały opisane klasy modelu danych i klasy modelu prezentacji systemu. Oprogramowanie jest zbudowane w taki sposób, aby można było wykorzystać szablon

  12. 76 FR 49532 - Federal Motor Vehicle Safety Standards; Electronic Stability Control; Technical Report on the...

    Science.gov (United States)

    2011-08-10

    ...-0112] Federal Motor Vehicle Safety Standards; Electronic Stability Control; Technical Report on the Effectiveness of Electronic Stability Control Systems for Cars and LTVs AGENCY: National Highway Traffic Safety..., Electronic Stability Control Systems. The report's title is: Crash Prevention Effectiveness in Light-Vehicle...

  13. Electron beam irradiation technology for environmental conservation

    International Nuclear Information System (INIS)

    Tokunaga, Okihiro; Arai, Hidehiko; Hashimoto, Shoji

    1992-01-01

    This paper reviews research and development of application of electron beam (EB) irradiation technology for treatment of flue gas and waste water, and for disinfection of sewage sludge. Feasibility studies on EB purification of flue gases have been performed with pilot-scale experiments in Japan, the USA and Germany, and is being carried out in Poland for flue gases from iron-sintering furnaces or coal burning boilers. Based on results obtained by experiments using simulated flue gas, pilot scale test for treatment of flue gas of low-sulfur containing coal combustion has recently started in Japan. Organic pollutants in waste water and ground water have been found to be decomposed by EB irradiation. Synergetic effect of EB irradiation and ozone addition was found to improve the decomposition efficiency. Electron beam irradiation technology for disinfection of water effluent from water treatment plants was found to avoid formation of chlorinated organic compounds which are formed in using chlorine. Efficient process for composting of sewage sludge disinfected by EB irradiation has been developed by small scale and pilot scale experiments. In the new process, disinfection by EB irradiation and composing can be done separately and optimum temperature for composting can be, therefore, selected to minimize period of composting. (author)

  14. Defining the "proven technology" technical criterion in the reactor technology assessment for Malaysia's nuclear power program

    Science.gov (United States)

    Anuar, Nuraslinda; Kahar, Wan Shakirah Wan Abdul; Manan, Jamal Abdul Nasir Abd

    2015-04-01

    Developing countries that are considering the deployment of nuclear power plants (NPPs) in the near future need to perform reactor technology assessment (RTA) in order to select the most suitable reactor design. The International Atomic Energy Agency (IAEA) reported in the Common User Considerations (CUC) document that "proven technology" is one of the most important technical criteria for newcomer countries in performing the RTA. The qualitative description of five desired features for "proven technology" is relatively broad and only provides a general guideline to its characterization. This paper proposes a methodology to define the "proven technology" term according to a specific country's requirements using a three-stage evaluation process. The first evaluation stage screens the available technologies in the market against a predefined minimum Technology Readiness Level (TRL) derived as a condition based on national needs and policy objectives. The result is a list of technology options, which are then assessed in the second evaluation stage against quantitative definitions of CUC desired features for proven technology. The potential technology candidates produced from this evaluation is further narrowed down to obtain a list of proven technology candidates by assessing them against selected risk criteria and the established maximum allowable total score using a scoring matrix. The outcome of this methodology is the proven technology candidates selected using an accurate definition of "proven technology" that fulfills the policy objectives, national needs and risk, and country-specific CUC desired features of the country that performs this assessment. A simplified assessment for Malaysia is carried out to demonstrate and suggest the use of the proposed methodology. In this exercise, ABWR, AP1000, APR1400 and EPR designs assumed the top-ranks of proven technology candidates according to Malaysia's definition of "proven technology".

  15. Advances in superconducting materials and electronics technologies

    International Nuclear Information System (INIS)

    Palmer, D.N.

    1990-01-01

    Technological barriers blocking the early implementation of ceramic oxide high critical temperature [Tc] and LHe Nb based superconductors are slowly being dismantled. Spearheading these advances are mechanical engineers with diverse specialties and creative interests. As the technology expands, most engineers have recognized the importance of inter-disciplinary cooperation. Cooperation between mechanical engineers and material and system engineers is of particular importance. Recently, several problems previously though to be insurmountable, has been successfully resolved. These accomplishment were aided by interaction with other scientists and practitioners, working in the superconductor research and industrial communities, struggling with similar systems and materials problems. Papers published here and presented at the 1990 ASME Winter Annual Meeting held in Dallas, Texas 25-30 November 1990 can be used as a bellwether to gauge the progress in the development of both ceramic oxide and low temperature Nb superconducting device and system technologies. Topics are focused into two areas: mechanical behavior of high temperature superconductors and thermal and mechanical problems in superconducting electronics

  16. New Desktop Virtual Reality Technology in Technical Education

    Science.gov (United States)

    Ausburn, Lynna J.; Ausburn, Floyd B.

    2008-01-01

    Virtual reality (VR) that immerses users in a 3D environment through use of headwear, body suits, and data gloves has demonstrated effectiveness in technical and professional education. Immersive VR is highly engaging and appealing to technically skilled young Net Generation learners. However, technical difficulty and very high costs have kept…

  17. Environmental applications of electron-beam technology

    International Nuclear Information System (INIS)

    Pikaev, A.K.

    2001-01-01

    The main directions of modern environmental applications of electron-beam technology are the following: 1) treatment of polluted natural and drinking water, municipal and industrial wastewater, other liquid wastes; 2) purification of gases; 3) treatment of sewage sludges; 4) treatment of solid wastes (medical wastes, contaminated soil and so on). In some cases, the results of respective researches and developments found a large-scale application. For example, recently several industrial plants for electron-beam purification of flue gases of thermal power plants from SO2 and NOx were created in China, Poland and Japan. In the report, a brief summary of the most important results obtained in the mentioned directions will be presented. A special attention will be paid to the data in the first direction. In particular, the recent results on radiation treatment of some liquid systems obtained in the laboratory under author's leadership will be considered. One of them is water polluted with petroleum products (motor oil, diesel fuel, residual fuel oil). The pollutants were present in water in dissolved form and as a separate phase. It was found that irradiation (dose 25-40 kGy) decomposes and removes the pollutants as a precipitate. The second system is natural oil gas consisting of gaseous and low-boiling hydrocarbons, water and so on. Laboratory- and pilot-scale (with electron accelerator of 0.7 MeV and 30 kW) studies have shown that electron-beam treatment (in a recycling regime with continuous sampling the liquid phase) of this gas leads to the formation of a mixture of liquid branched hydrocarbons, alcohols, ethers and so on, i.e., there is a radiation-induced liquefaction of the natural oil gas. The mechanism of radiolytic conversions occurring in the mentioned systems will be discussed

  18. Material Identification Technology (MIT) concept technical feasibility study

    International Nuclear Information System (INIS)

    Jones, J.L.; Harker, Y.D.; Yoon, W.Y.; Johnson, L.O.

    1993-09-01

    The Idaho National Engineering Laboratory (INEL) has initiated the design and development of a novel pulsed accelerator-based, active interrogation concept. The proposed concept, referred to as the Material Identification Technology (MIT), enables rapid (between accelerator pulses), non-destructive, elemental composition analysis of both nuclear and non-nuclear materials. Applications of this technique include material monitoring in support of counter-proliferation activities, such as export controls (at domestic and international inspection locations), SNM controls, nuclear weapon dismantlement, and chemical weapon verification. Material Identification Technology combines a pulsed, X-ray source (an electron accelerator) and a gamma detection system. The accelerator must maximize neutron production (pulse width, beam current, beam energy, and repetition rate) and minimize photon dose to the object. Current available accelerator technology can meet these requirements. The detection system must include detectors which provide adequate gamma energy resolution capability, rapid recovery after the initial X-ray interrogation pulse, and multiple single gamma event detection between accelerator pulses. Further research is required to develop the detection system. This report provides the initial feasibility assessment of the MIT concept

  19. Analysis of Technical Specifications of the Egyptian and French Electronic Storybooks (e-Storybook)

    Science.gov (United States)

    Atta, Mohammed Mahmoud; Abd El Wahab, Shaimaa Mahmoud

    2015-01-01

    This research aims at analysing technical specifications in a sample of Egyptian and French electronic storybooks (e-storybooks), to identify similarities and differences in technical specifications of children's e-storybooks and create a verified analysis list to be used for evaluation of e-storybooks. For this purpose, 32 e-storybooks in CD…

  20. Exploring the Capability of Evaluating Technical Solutions: A Collaborative Study into the Primary Technology Classroom

    Science.gov (United States)

    Björkholm, Eva

    2014-01-01

    Within the field of technology education, evaluating technical solutions is considered as an important topic. Research indicates that pupils have difficulties in evaluating technical solutions in terms of fitness for purpose, i.e. how effective a technical solution supports its intended function. By using the learning study, which is an iterative…

  1. Technical guideline technology according to the X-ray regulations

    International Nuclear Information System (INIS)

    2011-01-01

    The guideline covers the required technical knowledge concerning radiation protection and knowledge concerning for the operation of X-ray devices for technical purposes and stray radiation sources requiring licensing, and requirements for the qualification of officially authorized inspectors. The guidelines includes the following chapters: (1) introductory regulations; (2) Volume of the required technical knowledge; (3) Acquirement and certification of the technical knowledge; (4) Actualization of the technical knowledge; (5)Approval of courses and other training measures; (6) Combination of courses and training measures according to the guideline; (7) Requirements for qualification of officially authorized inspectors; (8) Interim regulations.

  2. The Interactive Electronic Technical Manual: Requirements, Current Status, and Implementation. Strategy Considerations.

    Science.gov (United States)

    1991-07-01

    authoring systems. Concurrently, great strides in computer-aided design and computer-aided maintenance have contributed to this capability. 12 Junod ...J.; William A. Nugent; and L. John Junod . Plan for the Navy/Air Force Test of the Interactive Electronic Technical Manual (IETM) at Cecil Field...AFHRL Logistics and Human Factors Division, WPAFB. Aug 1990. 12. Junod , John L. PY90 Interactive Electronic Technical Manual (IETM) Portable Delivery

  3. CERN Technical Training 2006: Software and System Technologies Curriculum - Scheduled

    CERN Multimedia

    2006-01-01

    Course Sessions (October 2006-March 2007) The Software and System Technologies Curriculum of the CERN Technical Training Programme offers comprehensive training in C++, Java, Perl, Python, XML, OO programming, JCOP/PVSS, database design and Oracle. In the PERL, C++, OO and Java course series there are some places available on the following course sessions, currently scheduled until March 2007: Object-Oriented Analysis and Design using UML: 17-19 October 2006 (3 days) JAVA 2 Enterprise Edition - Part 1: Web Applications: 19-20 October 2006 (2 days) JAVA - Level 1: 30 October -1 November 2006 (3 days) PERL 5 - Advanced Aspects: 2 November 2006 (1 day) C++ Programming Part 1 - Introduction to Object-Oriented Design and Programming: 14-16 November 2006 (3 days) JAVA - Level 2: 4-7 December 2006 (4 days) C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls: 12-15 December 2006 (4 days) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 18-20 December 2006 (3 days) C++ for Particle Physicists:...

  4. A Study to Determine the Basic Science and Mathematics Topics Most Needed by Engineering Technology Graduates of Wake Technical Institute in Performing Job Duties.

    Science.gov (United States)

    Edwards, Timothy I.; Roberson, Clarence E., Jr.

    A survey of 470 graduates of the six engineering technology programs at Wake Technical Institute--Architectural, Chemical, Civil Engineering, Computer, Electronic Engineering, and Industrial Engineering Technologies--and 227 of their employers was conducted in October, 1979, to determine the science and mathematics topics most needed by…

  5. [Integration of fundamental and applied medical and technical research made at the department of the biomedical systems, Moscow State Institute of Electronic Engineering].

    Science.gov (United States)

    Selishchev, S V

    2004-01-01

    The integration results of fundamental and applied medical-and-technical research made at the chair of biomedical systems, Moscow state institute of electronic engineering (technical university--MSIEE), are described in the paper. The chair is guided in its research activity by the traditions of higher education in Russia in the field of biomedical electronics and biomedical engineering. Its activities are based on the extrapolation of methods of electronic tools, computer technologies, physics, biology and medicine with due respect being paid to the requirements of practical medicine and to topical issues of research and design.

  6. Technical preparation of the Yuzhteploehnergomontazh trust for technological equipment mounting

    International Nuclear Information System (INIS)

    Zayats, A.I.

    1982-01-01

    Measures of technical preparation for equipment mounting at the Zaporozhe NPP developed with the Yuzhteploehnergomontazh trust experts are considered. These measures envisage the construction of mounting base of heat facilities, calculation of labour contents and determination of necessary quantity of mounters, development of optimal flowsheet of mounting control, improvement of mounting qualification and creation of stable collective body, improvement of technical level of mounting and welding works, organizational-technical measures on mounting logistics. Factors affecting negatively technical preparation quality of equipment mounting at the Zaporozhe NPP are discussed. The flowsheet of mounting control is presented

  7. Technology Acceptance of Electronic Medical Records by Nurses

    Science.gov (United States)

    Stocker, Gary

    2010-01-01

    The purpose of this study was to evaluate the Technology Acceptance Model's (TAM) relevance of the intention of nurses to use electronic medical records in acute health care settings. The basic technology acceptance research of Davis (1989) was applied to the specific technology tool of electronic medical records (EMR) in a specific setting…

  8. Strategy of technical innovation

    International Nuclear Information System (INIS)

    Lee, Ga Jong

    1990-12-01

    This book deals with policy of scientific technique and technical innovation such as research for development and types of technical innovation, historical development and process of technical innovation, economic growth, technology change and investment for research and development, structure and form of technical transfer with the meaning process, from, structure and theory, economic growth and investment of research and development with experiential analysis and case study on strategy of technical innovation in electron and fine chemical industry.

  9. Evaluating Instructor Technology Integration in Community and Technical Colleges: A Performance Evaluation Matrix

    Science.gov (United States)

    Del Favero, Marietta; Hinson, Janice M.

    2007-01-01

    The press for implementing technology based instructional delivery systems in community and technical colleges is well documented. Yet faculty face numerous challenges in integrating technology into instruction (AL-Bataineh & Brooks, 2003; Groves & Zemel, 2000; Khoury, 1997). Stimulating faculty ownership in technology, diffusion of technology use…

  10. Electronic resource management practical perspectives in a new technical services model

    CERN Document Server

    Elguindi, Anne

    2012-01-01

    A significant shift is taking place in libraries, with the purchase of e-resources accounting for the bulk of materials spending. Electronic Resource Management makes the case that technical services workflows need to make a corresponding shift toward e-centric models and highlights the increasing variety of e-formats that are forcing new developments in the field.Six chapters cover key topics, including: technical services models, both past and emerging; staffing and workflow in electronic resource management; implementation and transformation of electronic resource management systems; the ro

  11. Application of the Technology Acceptance Model (TAM) in electronic ...

    African Journals Online (AJOL)

    Application of the Technology Acceptance Model (TAM) in electronic ticket purchase for ... current study examined the perceived usefulness and ease of use of online technology ... The findings are discussed in the light of these perspectives.

  12. Final Technical Report: Electronic Structure Workshop (ES13)

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Shiwei [College of William and Mary, Williamsburg, VA (United States)

    2015-02-26

    The 25th Annual Workshop on Recent Developments in Electronic Structure Methods (ES2013) was successfully held at the College of William & Mary in Williamsburg VA on June 11-14, 2013. The workshop website is at http://es13.wm.edu/ , which contains updated information on the workshop and a permanent archive of the scientific contents. DOE's continued support has been instrumental to the success of the workshop.

  13. CLOUD TECHNOLOGIES IN MANAGEMENT AND EDUCATIONAL PROCESS OF UKRAINIAN TECHNICAL UNIVERSITIES

    Directory of Open Access Journals (Sweden)

    Yu. Tryus

    2014-06-01

    Full Text Available This study analyzes opportunities for using cloud technologies in higher education in Ukraine. On the basis of principles of the system approach, it examines the main task of cloud technologies, strategic and tactical goals of cloud computing at the technical universities, as well as problems that arise in their implementation in the educational process. The paper discusses the main trends in the use of cloud technologies in higher technical education, analyzes cloud services used by leading technical universities in Ukraine in management and learning. The typical structure of a Technical University is considered with public, private, and hybrid clouds. The experience of Cherkasy State Technological University in the use of cloud technologies at management and learning is presented. Considerations are particularly given to distance support, mobile, and blending learning, virtualization mechanism to support the students learning at natural, mathematical sciences and engineering through the utilization of individual desktops.

  14. Realizing what's essential: a case study on integrating electronic journal management into a print-centric technical services department.

    Science.gov (United States)

    Dollar, Daniel M; Gallagher, John; Glover, Janis; Marone, Regina Kenny; Crooker, Cynthia

    2007-04-01

    To support migration from print to electronic resources, the Cushing/Whitney Medical Library at Yale University reorganized its Technical Services Department to focus on managing electronic resources. The library hired consultants to help plan the changes and to present recommendations for integrating electronic resource management into every position. The library task force decided to focus initial efforts on the periodical collection. To free staff time to devote to electronic journals, most of the print subscriptions were switched to online only and new workflows were developed for e-journals. Staff learned new responsibilities such as activating e-journals, maintaining accurate holdings information in the online public access catalog and e-journals database ("electronic shelf reading"), updating the link resolver knowledgebase, and troubleshooting. All of the serials team members now spend significant amounts of time managing e-journals. The serials staff now spends its time managing the materials most important to the library's clientele (e-journals and databases). The team's proactive approach to maintenance work and rapid response to reported problems should improve patrons' experiences using e-journals. The library is taking advantage of new technologies such as an electronic resource management system, and library workflows and procedures will continue to evolve as technology changes.

  15. Treating limbs with electrons: creative solutions to technical problems

    International Nuclear Information System (INIS)

    Hornby, C.

    1993-01-01

    The treatment of superficial lesions on limbs involving large areas of skin has long presented a challenge to radiation therapists. In the 1990's the use of electrons provides a good selection of field sizes and beam penetrations. However, the rapidly varying contours of limbs as well as their mobility, continues to necessitate solutions to the problems of accurate field definition, homogeneous dose in particularly at beam junctions and, simple but effective patient stabilization. This paper offers several examples of creative solutions to these problems. 8 refs., 17 figs

  16. Values of Modern Technology to Electronic Media Management in ...

    African Journals Online (AJOL)

    This paper examines the influence, impact and communicative values of modern technology to electronic media management in Nigeria. It evaluates changes in distribution and consumer technologies, the impact on media content, new business models for the electronic media, and concludes with a discussion of issues ...

  17. 48 CFR 311.7000 - Defining electronic information technology requirements.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Defining electronic information technology requirements. 311.7000 Section 311.7000 Federal Acquisition Regulations System HEALTH... Accessibility Standards 311.7000 Defining electronic information technology requirements. HHS staff that define...

  18. Applications and advances in electronic-nose technologies

    Science.gov (United States)

    A. D. Wilson; M. Baietto

    2009-01-01

    Electronic-nose devices have received considerable attention in the field of sensor technology during the past twenty years, largely due to the discovery of numerous applications derived from research in diverse fields of applied sciences. Recent applications of electronic nose technologies have come through advances in sensor design, material improvements, software...

  19. Ion Implantation Processing Technologies for Telecommunications Electronics

    Energy Technology Data Exchange (ETDEWEB)

    Haynes, T E

    2000-05-01

    The subject CRADA was a collaboration between Oak Ridge National Laboratory and Bell Laboratories, Lucent Technologies (formerly AT and T Bell Laboratories) to explore the development of ion implantation technologies for silicon integrated circuit (IC) manufacturing.

  20. Appropriability, Technological Opportunity, Market Demand, and Technical Change - Empirical Evidence from Switzerland

    OpenAIRE

    Harabi, Najib

    1992-01-01

    The purpose of this paper is to analyze both theoretically and empirically those factors which underlay the - empirically observable - inter-industry differences in technical progress. At the theoretical level economists agree more and more that technical progress can be explained at the industry level by the following three factors: (1) the technological opportunities, (2) the appropriability conditions, meaning the ability to capture and protect the results of technical innovations and (3) ...

  1. Examining the Role of Transformational Leadership in Technology Adoption: Evidence from Bruneian Technical & Vocational Establishments (TVE)

    Science.gov (United States)

    Seyal, Afzaal H.

    2015-01-01

    This pioneering study discusses the thirty-five Bruneian technical & vocational institutions of top management (principals, deputy principals, senior masters, ICT coordinators and technical administrators) leadership style with the adoption of Information and Communication Technologies (ICT). The study uses a survey approach further to…

  2. "You Will": Technology, Magic, and the Cultural Contexts of Technical Communication.

    Science.gov (United States)

    Kitalong, Karla Saari

    2000-01-01

    Provides some background on the use of magical language in technical contexts, gives examples of magical discourse in technology advertisements and newsmagazine articles, and proposes a technical communication pedagogy of media analysis. Notes that the proposed pedagogy involves students conducting diagnostic critiques of media texts and affords…

  3. Blurring the Lines: Leveraging Internet Technology for Successful Blending of Secondary/Post-Secondary Technical Education

    Science.gov (United States)

    Ryan, Kenneth; Kopischke, Kevin

    2008-01-01

    The Remote Automation Management Platform (RAMP) is a real-time, interactive teaching tool which leverages common off-the-shelf internet technologies to provide high school learners extraordinary access to advanced technical education opportunities. This outreach paradigm is applicable to a broad range of advanced technical skills from automation…

  4. Next Generation Nuclear Plant Project Technology Development Roadmaps: The Technical Path Forward

    Energy Technology Data Exchange (ETDEWEB)

    John Collins

    2009-01-01

    This document presents the Next Generation Nuclear Plant (NGNP) Systems, Subsystems, and Components, establishes a baseline for the current technology readiness status, and provides a path forward to achieve increasing levels of technical maturity.

  5. TECHNOLOGICAL APPROACH TO TEACHING FOREIGN LANGUAGES IN TECHNICAL UNIVERSITIES

    Directory of Open Access Journals (Sweden)

    Mariia Kuts

    2016-11-01

    Full Text Available Modern learning foreign languages is based on a humanistic paradigm. The realization of the possibility of such activity researches consider in implementation of technological approach in educational process. The scientists connect the optimal and qualitative realization of this activity with the implementation of education technology into learning process. Modern studies are focused on questions of implementation of technological approach into teaching foreign languages. It is thought to allow to achieve guaranteed minimal level of learning results. At the same time there are some incompletely studied aspects such as content of pedagogical technologies, their conceptual and procedural characteristics, approaches to classification. In the article the essence of technological approach is revealed, the communicatively focused technologies of teaching foreign languages in non-linguistic universities are concretized. The interpretation of technological approach is given; characteristics and attributes in teaching foreign languages are selected. It is noticed that technological approach is social and engineering ideology in the sphere of didactics according to which teaching process is considered to be a completely designed process with strictly planned and fixed results (M. Klarin. In the article it is emphasized on feasibility and efficiency of technological approach while teaching foreign languages, the degree of its integration in educational process is defined. The communication-oriented technologies, based on a communicative method of E. Passov, are allocated as the most optimum. It is shown the communication-oriented technologies go beyond the conceptual idea of modelling in teaching process of real foreign-language communication, and their procedural component and contents are founded on certain principles. The most commonly used technologies of teaching foreign languages are classified as technologies of modernization and technologies of

  6. Technical report of electronics shop characteristics of high speed electronics component, (1)

    International Nuclear Information System (INIS)

    Watanabe, Shin-ichi; Shiino, Kazuo.

    1975-01-01

    We must develop electronics circuits for high speed signals. The electronics components of the circuits make use of the special components. This report treats a pulse response of the electronics components (i.e. coaxial cable, connector, resistor, capacitor, diode, transistor) for high speed electronics. The results of this report was already applied constructions of high speed electronics circuits and experimental equipments of the High Energy Physics Division. (auth.)

  7. Electronic health records and technical assistance to improve quality of primary care: Lessons for regional extension centers.

    Science.gov (United States)

    Boas, Samuel J; Bishop, Tara F; Ryan, Andrew M; Shih, Sarah C; Casalino, Lawrence P

    2014-07-01

    In 2009, the American Recovery and Reinvestment Act apportioned $643 million for a Health Information Technology Extension Program, which established Regional Extension Centers (RECs) to support the implementation and use of electronic health records (EHRs). Little is known, however, about how RECs should assist in EHR implementation and how they should structure ongoing support. The purpose of this paper is to describe physicians' experiences with the Primary Care Information Project (PCIP), an REC run by the New York City Department of Health and Mental Hygiene. We interviewed 17 physicians enrolled in PCIP to understand the role of the EHRon quality of care and their experience with technical assistance from PCIP. All physicians stated that they felt that the EHR improved the quality of care they delivered to their patients particularly because it helped them track patients. All the physicians found technical assistance helpful but most wanted ongoing assistance months or years after they adopted the EHR. © 2013 Published by Elsevier Inc.

  8. Technical and economical aspects of SO2 and NOx removal from flue gas by electron beam irradiation

    International Nuclear Information System (INIS)

    Turhan, S.; Karadeniz, S.; Tugluoglu, N.; Eken, M.; Oktar, O.; Ercan, I.

    2001-01-01

    The emission of sulfur dioxide (SO 2 , also SO 3 ) and nitrogen oxides (NO, NO 2 , called NO x ) from fossil fuel burning power and industrial plants is one of the major sources of environmental pollution. These pollutants are named as acid gases causing acid rain and also indirect greenhouse gases contributing greenhouse effect. Acid rain damages forest, agriculture fields and flora, and cause public health concerns in regions having a number of industrial plants. Today, many countries have started to impose industrial emission limits and this movement has generated renewed interest in finding viable and cost effective solutions to SO 2 and NO x pollution control. The conventional technologies, wet scrubbing de-SO 2 and de-NO x , now reached their full potential therefore these methods are not expected to provide further improvements in terms of efficiency or reduction in construction costs. However, new technologies are being investigated for industrial scale commercial viability. One of them is electron beam process, which is dry scrubbing process and simultaneously removes SO 2 and NO x , and useful by-product for agriculture fertilizer. In this study, the economical and technical aspects of electron beam flue gas treatment process are discussed. Because an electron accelerator facility with electron beam energy of 500 KeV and electron beam current of 20 mA will be installed at ANRTC in TURKEY

  9. Development of nuclear technology through International Technical Cooperation programme: Malaysian experience

    International Nuclear Information System (INIS)

    Ainul Hayati Daud

    1997-01-01

    In the advent of new technologies and knowledge, countries need to rely on one another for progress and development. At the same time, new challenges to development, which are beyond the competence of any country to approach individually, have emerged. These have led to greater need for international co-operation, particularly among the developing countries. In Malaysia, international technical co-operation has contributed significantly towards the development of nuclear technology. Malaysia has received technical assistance through the multilateral, regional and bilateral co-operation. This assistance complements the efforts of the government to meet the primary objectives of science and technology programme, which are; intensification of R and D capacity and applications of technologies, both acquired and developed, in national development. Over the last one and a half decade, more than 70 projects valued almost USD 15 millions, were implemented under the Technical Assistance Programme of the International Atomic Energy Agency and the Bilateral Technical Assistance Programme of Japan and Australia. Malaysia also has benefited from the regional technical co-operation programme such Regional Co-operative Agreement for Asia and Pacific Region, United Nation Department Programme, International Nuclear Co-operation in Asia. While receiving assistance, Malaysia continues to assist other developing countries in their development efforts in the fields of nuclear technology, through the various international co-operation programmes. This report reviews the technical assistance received through the international co-operation and its contributions towards the development of nuclear technology in Malaysia for period 1980 - 1996

  10. Electronics in nuclear science and technology

    International Nuclear Information System (INIS)

    Dastidar, P.R.

    1979-01-01

    Electronics plays a vital role in the field of nuclear research and industry. Nuclear instrumentation and control systems rely heavily on electronics for reliable plant operation and to ensure personnel safety from harmful radiations. Rapid developments in electronics have resulted in the gradual phasing out of pneumatic instruments and replacement by solid-state electronic systems. On-line computers are now being used extensively for centralised monitoring and control of large nuclear plants. The paper covers the following main topics: (i) radiation detection and measurement, (ii) systems for nuclear research and design, (iii) nuclear reactor control and safety systems and (iv) modern trends in reactor control and nuclear instrumentation systems. The methods for radiation detection, ionization chambers, self-powdered detectors and semiconductor detectors are discussed in brief, followed by the description of the electronic systems commonly used in nuclear research, namely the pulse height, multichannel, correlation and fourier analysers. NIM and CAMAC, the electronic system standards used in nuclear laboratories/industries are also outlined. Electronic systems used for nuclear reactor control, safety, reactor core monitoring, failed fuel detection and process control instrumentation, have been described. The application of computers to reactor control, plant data processing, better man-machine interface and the use of multiple computer systems for achieving better reliability have also been discussed. Micro-computer based instrumentation systems, computers in reactor safety and advanced nuclear instrumentation techniques are briefly illustrated. (auth.)

  11. Organized technology. Networks and innovation in technical systems

    International Nuclear Information System (INIS)

    Shrum, W.

    1985-01-01

    The book is based on a study of radioactive waste and solar cell research. Social network methods are used to illuminate the differences between technologies such as nuclear waste disposal, dominated by the federal government, and potentially profitable technologies such as photovoltaics, where the private sector plays a larger role. The book examines the interaction of government agencies, national laboratories, private firms, universities, regulatory agencies, Congress, and public-interest groups in the technology development process

  12. Advanced Instrumentation, Information, and Control Systems Technologies Technical Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    Bruce Hallbert

    2012-09-01

    Reliable instrumentation, information, and control (II&C) systems technologies are essential to ensuring safe and efficient operation of the U.S. light water reactor (LWR) fleet. These technologies affect every aspect of nuclear power plant (NPP) and balance-of-plant operations. In 1997, the National Research Council conducted a study concerning the challenges involved in modernization of digital instrumentation and control systems in NPPs. Their findings identified the need for new II&C technology integration.

  13. Recent developments in electron beam machine technology

    International Nuclear Information System (INIS)

    Sadat, T.; Ross, A.; Leveziel, H.

    1994-01-01

    Electron beam accelerator provides ionisation energy for industrial processing. Electron beam accelerators are increasingly used for decontamination, conservation and disinfestation of food, for sterilization of medical products, and for polymerisation of materials. These machines are easy to install into a production factory as the radiation stops as soon as the machine is switched off. This safety advantage, together with the flexibility of use of these highly automated machines, has allowed the electron beam accelerator to become an important production tool. (author). 23 refs., 6 figs., 2 tabs

  14. Economic and technical assay of the application of radionuclide technology

    International Nuclear Information System (INIS)

    Emrich, F.G.

    1976-05-01

    The dynamically loaded components of combustion engines undergo wear during operation as a function of the operating points and the operating parameters selected. Radionuclide measurement methods developed in the Federal Republic of Germany in the LIT laboratory of Gesellschaft fuer Kernforschung allow to determine the wear of machine components during operation, contrary to conventional length measurement techniques. In the first part of this work the existing wear problems will be analyzed and investigations will be made into the capacities of conventional and radionuclide measurement methods. Based on this, a cost-benefit analysis system was developed for evaluation under technical and economical aspects of the use of different measurement methods allowing to solve detailed wear problems. This system furnishes results on the respective optimum wear measurement method relating to the actual problem and taking into account the relevant technical and economical boundary conditions. (orig.) [de

  15. 25 CFR 547.14 - What are the minimum technical standards for electronic random number generation?

    Science.gov (United States)

    2010-04-01

    ... random number generation? 547.14 Section 547.14 Indians NATIONAL INDIAN GAMING COMMISSION, DEPARTMENT OF... CLASS II GAMES § 547.14 What are the minimum technical standards for electronic random number generation...) Unpredictability; and (3) Non-repeatability. (b) Statistical Randomness.(1) Numbers produced by an RNG shall be...

  16. Developing a Template for Electronic Portfolios in Career and Technical Education

    Science.gov (United States)

    Fowler, Matthew

    2012-01-01

    The purposes of this multiple case study were to determine if manufacturing and services sector employers found value in the use of an ePortfolio in the hiring process, and to develop a suggested template for an ePortfolio format to be used within career and technical education. Electronic portfolios "allow students to showcase their…

  17. Technology and application of two sets of industrial electron accelerators

    International Nuclear Information System (INIS)

    Hua Degen

    2000-01-01

    The radiation industry in China Academy of Engineering Physics (CAEP) has had a big scale, and the two sets of industrial electron accelerators play important roles. The Electron Processing System (E.P.S), which was introduced in 1987, is a powerful electron accelerator. And the 10 MeV Accelerator, which is a traveling wave linear electron accelerator, has the higher electron energy. Both of the stes are equipped the driving devices under the beam, and has made a considerable economic results. This article describes the technology and application of the two electron accelerators. (author)

  18. Electron Conditioning of Technical Aluminium Surfaces: Effect on the Secondary Electron Yield

    Energy Technology Data Exchange (ETDEWEB)

    Le Pimpec, F.

    2004-12-13

    The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (< 1.3, value of many pure elements [1] ), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

  19. Glossary of technical terms for the medical technology professionals.

    Directory of Open Access Journals (Sweden)

    Rafael Felipe García Rodríguez

    2014-03-01

    Full Text Available The current work is a glossary of technical terms in English language for Medical Health Professionals, has been prepared due to the lack of technical lexicon the students have during and after their university studies, that is, the students have a deficit of technical words which limits their professional competence and accountability. This shortage limits them and makes it a great laboring challenge if they have to work overseas in English-speaking countries. The glossary comprises the main and necessary words which are needed for this type of professional in their field of action. These graduates have a solid knowledge and comprehension of biological, biochemical and biophysical fundamentals in their mother tongue but they do not have the necessary elements in the target language to operate properly. It is a need that they can work appropriately in the spheres of prevention, promotion and health recovery to support a diagnosis, a treatment and a management not only in their mother tongue but in English for their future work.

  20. Technology of irradiation of liquids by electron beams

    International Nuclear Information System (INIS)

    Tofaute, K.

    1979-01-01

    The methods of pretreatment, the technical details of the irradiating equipment, the applied radiation doses and the general requirements of the effectively working system are described. The extent of reinfection is compared in cases of heat-treated and electron-irradiated mud. The latter method gave significantly better results. (L.E.)

  1. Deploying Electronic Roadside Vehicle Identification Technology to ...

    African Journals Online (AJOL)

    ... suicide bombing, ritual murders and human parts selling. ..... Table 1.1: Prototype Platforms For VANET And WSN Nodes [11] ... store items are common examples. This is the one .... viewed on electronic maps via the internet or specialized ...

  2. Electron accelerator technology research in food irradiation

    International Nuclear Information System (INIS)

    Jin Jianqiao; Ye Mingyang; Zhang Yue; Yang Bin; Xu Tao; Kong Xiangshan

    2014-01-01

    Electronic accelerator was applied to instead of cobalt sources for food irradiation, to keep food quality and to improve the effect of the treatment. Appropriate accelerator parameters lead to optimal technique. The irradiation effect is associated with the relationship between uniformity and irradiating speed, the effect of cargo size on radiation penetration, as well as other factors that affect the irradiation effects. Industrialization of electron accelerator irradiation will be looked to the future. (authors)

  3. The non-technical side of office technology

    NARCIS (Netherlands)

    Ruel, Hubertus Johannes Maria

    2001-01-01

    Many office technology projects fail. The outcomes of these projects are often not in line with initial expectations. This book assumes that this disappointing result is largely the result of the fact that office technology projects are too IT-driven. The basic assumption is that the problems

  4. Panel Debate: Technics and technology in mathematics and mathematics education

    DEFF Research Database (Denmark)

    Misfeldt, Morten

    2015-01-01

    The use of computer technology for teaching and learning of mathematics has several consequences and does sometimes give rise to both controversies and misunderstandings. We address these problems by both a philosophical and a historical approach, investigating what it actually is that goes on when...... guidelines and conclusions regarding the use of computer technology in mathematics education....... new technologies enter mathematics as a discipline and mathematics education as a societal practice. Our analysis suggests a focus on continuities in time and place in the sense that it is necessary to understand the history of “tool use” in mathematics and the various ways that scholastic and non...

  5. HIGH VOLTAGE ENVIRONMENTAL APPLICATIONS, INC.ELECTRON BEAM TECHNOLOGY - INNOVATIVE TECHNOLOGY EVALUATION REPORT

    Science.gov (United States)

    This report evaluates a high-voltage electron beam (E-beam) technology's ability to destroy volatile organic compounds (VOCs) and other contaminants present in liquid wastes. Specifically, this report discusses performance and economic data from a Superfund Innovative Technology...

  6. Challenges in legislation, recycling system and technical system of waste electrical and electronic equipment in China.

    Science.gov (United States)

    Zhang, Shengen; Ding, Yunji; Liu, Bo; Pan, De'an; Chang, Chein-chi; Volinsky, Alex A

    2015-11-01

    Waste electrical and electronic equipment (WEEE) has been one of the fastest growing waste streams worldwide. Effective and efficient management and treatment of WEEE has become a global problem. As one of the world's largest electronic products manufacturing and consumption countries, China plays a key role in the material life cycle of electrical and electronic equipment. Over the past 20 years, China has made a great effort to improve WEEE recycling. Centered on the legal, recycling and technical systems, this paper reviews the progresses of WEEE recycling in China. An integrated recycling system is proposed to realize WEEE high recycling rate for future WEEE recycling. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Technical rigidity and appropriate technology in less-developed countries

    Energy Technology Data Exchange (ETDEWEB)

    Forsyth, D J.C. [Univ. of Strathyclyde, England; McBain, N S; Solomon, R F

    1980-05-01

    The extent to which the use of capital-intensive methods in LDCs can properly be ascribed to the inherent rigidity of the factor proportions embodied in modern technology - rather than to distortions and aberrrations in the process of technology choice - is still a matter of considerable uncertainty after two decades of debate. In this study, an engineering-based index is developed to summarize the opportunities for, and barriers to, substitution of labor for capital in a wide range of industries. The index is used to compare the technology actually installed in manufacturing in Ghana, the Philippines, Turkey, and Malaysia with the feasible alternatives. The finding that opportunities for use of labor-intensive methods are to a large extent exploited is interpreted as casting doubt on the ability of even the most appropriate choice from currently feasible technologies to reduce unemployment significantly. 46 references, 5 figures, 6 tables.

  8. Floating natural gas processing plants. Technical ideal or feasible technology

    Energy Technology Data Exchange (ETDEWEB)

    Backhaus, H

    1977-04-01

    Realizability of floating natural gas processing plants is decisively influenced by the economy of the system. Illustrated by the example of the natural gas product LPG (liquefied petroleum gas), a model cost calculation is carried out. It is demonstrated that the increase in the price level during the 1973/1974 energy crisis is an important factor for the realiability in terms of economy of such complicated technical systems. Another aspect which the model calculation revealed is that the economy of floating natural gas processing plants and storage systems can only be estimated in connection with other system components.

  9. Research on technical and technological parameters of inclined drilling

    Directory of Open Access Journals (Sweden)

    М. В. Двойников

    2017-03-01

    Analysis of investigation results showed that the main source of oscillations is linked to bending and compressing stresses, caused by well deviations as well as rigidity of the drilling tool. In effect, in the bottom-hole assembly occur auto-oscillations, making it impossible to correct azimuth and zenith angles. Alteration of rigidity in the bottom part of the tool and drilling parameters, implying reduced rotation speed of the drill string and regulation of drill bit pressure, can partially solve this problem, though increase in rotation speed is limited by technical characteristics of existing top drive systems.

  10. Teaching ethics and technology with Agora, an electronic tool

    NARCIS (Netherlands)

    Burg, van der S.; Poel, van de I.R.

    2005-01-01

    Courses on ethics and technology have become compulsory for many students at the three Dutch technical universities during the past few years. During this time, teachers have faced a number of didactic problems, which are partly due to a growing number of students. In order to deal with these

  11. Technologies and Capabilities in: Communications, Electronics and IT (Information Technologies)

    National Research Council Canada - National Science Library

    1998-01-01

    ... and has offices in several international cities, including Brussels and Moscow. DERA is composed of hundreds of specialist teams, each of which is an expert in its particular technology or facility...

  12. Teaching Power Electronics with a Design-Oriented and Project-Based Learning Method at the Technical University of Denmark

    DEFF Research Database (Denmark)

    Zhang, Zhe; Hansen, Claus Thorp; Andersen, Michael A. E.

    2016-01-01

    Power electronics is a fast developing technology within the electrical engineering field. This paper presents the results and experiences gained from DesignOriented Project Based Learning of switch-mode power supply design within a power electronics course at the Technical University of Denmark...... (DTU). Project-based learning (PBL) is known to be a motivating and problem-centered teaching method that not only places students at the core of the teaching and learning activities but also gives students the ability to transfer their acquired scientific knowledge into industrial practices. Students...... are asked to choose a specification from different power converter applications such as a fuel cell power conditioning converter, a light-emitting diode (LED) driver or a battery charger. Based upon their choice, the students select topology, design magnetic components, calculate input/output filters...

  13. Socio-Technical Considerations for the Use of Blockchain Technology in Healthcare.

    Science.gov (United States)

    Wong, Ming Chao; Yee, Kwang Chien; Nøhr, Christian

    2018-01-01

    Blockchain technology is often considered as the fourth industrial revolution that will change the world. The enthusiasm of the transformative nature of blockchain technology has infiltrated healthcare. Blockchain is often seen as the much needed and perfect technology for healthcare, addressing the difficult and complex issues of security and inter-operability. More importantly, the "value" and trust-based system can deliver automated action and response via its smart contract mechanism. Healthcare, however, is a complex system. Health information technology (HIT) so far, has not delivered its promise of transforming healthcare due to its complex socio-technical and context sensitive interaction. The introduction of blockchain technology will need to consider a whole range of socio-technical issues in order to improve the quality and safety of patient care. This paper presents a discussion on these socio-technical issues. More importantly, this paper argues that in order to achieve the best outcome from blockchain technology, there is a need to consider a clinical transformation from "information" to "value " and trust. This paper argues that urgent research is needed to address these socio-technical issues in order to facilitate best outcomes for blockchain in healthcare. These socio-technical issues must then be further evaluated by means of working prototypes in the medical domain in coming years.

  14. Technical innovations in communication : how to relate technology to business by a culturally reliable human interface

    NARCIS (Netherlands)

    Ulijn, J.M.; Campbell, Ch.; Malkinson, T.

    1999-01-01

    The technology that makes the world into the global village envisioned by Marshall McLuhan more than 30 years ago now seems to be in place. thanks to the Internet and the World Wide Web. Technical innovations in communication technology have been quickly exploited by businesses to expand their reach

  15. Electronics Technology. Tech Prep Competency Profile.

    Science.gov (United States)

    Lakeland Tech Prep Consortium, Kirtland, OH.

    This tech prep competency profile covers the occupation of electronics technician. Section 1 provides the occupation definition. Section 2 lists development committee members. Section 3 provides the leveling codes--abbreviations for grade level, (by the end of grade 12, by the end of associate degree), academic codes (communications, math, or…

  16. Proceedings of symposium on technology in laboratories by department of engineering and technical services

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-06-01

    The Symposium on Technology in Laboratories was held on March 14 and 15 at Ceratopia Toki in Toki City, Gifu Prefecture, Japan. This symposium was hosted by National Institute for Fusion Science (NIFS). There were 407 participants from many Japanese universities, national laboratories, technical colleges and from some Japanese Industrial world. One hundred and thirty one papers were presented in the symposium. Technical experience and new techniques were reported and discussed being divided into five sessions; technology of fabrication, device technology, diagnostic and control system, cryogenics, computer and data processing. (author)

  17. Transactions on the Precision and Electronic Technology. Vol. 4

    International Nuclear Information System (INIS)

    1999-01-01

    The conference covers most important subjects connected with application of electronic technologies for resistors, sensors, radiation detectors and other microelectronic structures. The investigations of physical properties (electrical and magnetic properties, crystal structure etc.) of interest materials have been also presented

  18. Future orbital transfer vehicle technology study. Volume 2: Technical report

    Science.gov (United States)

    Davis, E. E.

    1982-01-01

    Missions for future orbit transfer vehicles (1995-2010) are identified and the technology, operations and vehicle concepts that satisfy the transportation requirements are defined. Comparison of reusable space and ground based LO2/LH2 OTV's was made. Both vehicles used advanced space engines and aero assist capability. The SB OTV provided advantages in life cycle cost, performance and potential for improvement. Comparison of an all LO2/LH2 OTV fleet with a fleet of LO2/LH2 OTVs and electric OTV's was also made. The normal growth technology electric OTV used silicon cells with heavy shielding and argon ion thrusters. This provided a 23% advantage in total transportation cost. The impact of accelerated technology was considered in terms of improvements in performance and cost effectiveness. The accelerated technology electric vehicle used GaAs cells and annealing but did not result in the mixed fleet being any cheaper than an all LO2/LH2 OTV fleet. It is concluded that reusable LO2/LH2 OTV's can serve all general purpose cargo roles between LEO and GEO for the forseeable future. The most significant technology for the second generation vehicle would be space debris protection, on-orbit propellant storage and transfer and on-orbit maintenance capability.

  19. A systematic review of portable electronic technology for health education in resource-limited settings.

    Science.gov (United States)

    McHenry, Megan S; Fischer, Lydia J; Chun, Yeona; Vreeman, Rachel C

    2017-08-01

    The objective of this study is to conduct a systematic review of the literature of how portable electronic technologies with offline functionality are perceived and used to provide health education in resource-limited settings. Three reviewers evaluated articles and performed a bibliography search to identify studies describing health education delivered by portable electronic device with offline functionality in low- or middle-income countries. Data extracted included: study population; study design and type of analysis; type of technology used; method of use; setting of technology use; impact on caregivers, patients, or overall health outcomes; and reported limitations. Searches yielded 5514 unique titles. Out of 75 critically reviewed full-text articles, 10 met inclusion criteria. Study locations included Botswana, Peru, Kenya, Thailand, Nigeria, India, Ghana, and Tanzania. Topics addressed included: development of healthcare worker training modules, clinical decision support tools, patient education tools, perceptions and usability of portable electronic technology, and comparisons of technologies and/or mobile applications. Studies primarily looked at the assessment of developed educational modules on trainee health knowledge, perceptions and usability of technology, and comparisons of technologies. Overall, studies reported positive results for portable electronic device-based health education, frequently reporting increased provider/patient knowledge, improved patient outcomes in both quality of care and management, increased provider comfort level with technology, and an environment characterized by increased levels of technology-based, informal learning situations. Negative assessments included high investment costs, lack of technical support, and fear of device theft. While the research is limited, portable electronic educational resources present promising avenues to increase access to effective health education in resource-limited settings, contingent

  20. Status report on the relativistic electron beam technology

    International Nuclear Information System (INIS)

    Iyyengar, S.K.; Ron, P.H.; Rohatgi, V.K.

    1974-01-01

    The status of technology of the pulsed relativistic electron beam (REB) has been examined and summarised in this report. With the present technology the beam generator can be used either as a source of intense electron burst or to produce bursts of positive ions x and γ-rays, and neutrons by suitable secondary reactions. A large number of applications have been identified where this technology can play an important role. Typical applications of the technology include : (a) generation and heating of fusion plasma (b) development of high power laser and (c) sterilisation and radiation sources. The present day cost of radiation produced by REB is competitive with the cost of radiation produced from Co 60 source. At the same time there are indications that the cost of radiation from REB source can be significantly reduced with advanced technology. The type of equipment developed by various laboratories to study realitivistic electron beams is also included in this report. (author)

  1. Technical and technological solution for vegetal bio-stimulants obtaining

    Science.gov (United States)

    Anghelache, D. G.; Diaconescu, I.; Pătraşcu, R.

    2017-08-01

    The paper presents a modern technology for bio fertilizers resulted from waste plant mass after harvesting crops Experimental products were obtained rich in nutrients, but unstable in terms of existing microorganisms. Therefore, they conducted further studies to obtaining bio fungicide herb, so in all investigations undertaken so far in the laboratory, were able to conclude that the introduction of medicinal plant extracts with fungicidal effect into the bio fertilizers obtained by degradation of plant material post-harvest can get various bio-stimulants with nourishing effect upon the plants. Following this technology the paper’s objective is to identify a flux scheme for experimental equipment which can produce as final outcome this type of bio-stimulant. Also, in this work, this equipment will be chosen and will be designed following and obeying to the request of every step of the above technology.

  2. Technical Training: ELEC-2005 - Electronics in High Energy Physics: Summer Term (May 2005)

    CERN Multimedia

    Davide Vitè

    2005-01-01

    ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the successful ELEC-2002 course series.This comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms. The last two Terms will run with the following schedule: Summer Term: System electronics for physics: Issues (May, 7 lectures) - now open for registration Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) Lectures within each Term will take place on Tuesdays and Thursdays, from 10h00 to 12h30. The course will be in English, with questions and answers also possible in French. Separate registrati...

  3. Control system in the technological electron linacs

    International Nuclear Information System (INIS)

    Boriskin, V.N.; Akchurin, Yu.I.; Bahmetev, N.N.; Gurin, V.A.

    1999-01-01

    The special system has been developed for linac control.It controls the electron beam current,the energy and the position,protects the accelerating and scanning systems from the damage caused by the beam;blocks the modulator and the klystron amplifier in the case of intolerable operating modes;regulates the phase and power of the HF signals in the injecting system and also regulates the source power currents in the magnetic system

  4. Technological guns which form the profiled electron beans

    International Nuclear Information System (INIS)

    Mel'nik, V.I.

    1998-01-01

    Electron guns with high-voltage glow discharge are developed which form disc - and tubule-like,hollow conic and linear electron beams,as well as devices and systems for control of gun parameter and technological processes in low and intermediate vacuum

  5. The Impact of Electronic Communication Technology on Written Language

    Science.gov (United States)

    Hamzah, Mohd. Sahandri Gani B.; Ghorbani, Mohd. Reza; Abdullah, Saifuddin Kumar B.

    2009-01-01

    Communication technology is changing things. Language is no exception. Some language researchers argue that language is deteriorating due to increased use in electronic communication. The present paper investigated 100 randomly selected electronic mails (e-mails) and 50 short messaging system (SMS) messages of a representative sample of…

  6. CERN's web application updates for electron and laser beam technologies

    CERN Document Server

    Sigas, Christos

    2017-01-01

    This report describes the modifications at CERN's web application for electron and laser beam technologies. There are updates at both the front and the back end of the application. New electron and laser machines were added and also old machines were updated. There is also a new feature for printing needed information.

  7. Second Information Technology in Education Study: SITES 2006 Technical Report

    Science.gov (United States)

    Carstens, Ralph, Ed.; Pelgrum, Willem J., Ed.

    2009-01-01

    The International Association for the Evaluation of Educational Achievement (IEA) has been conducting comparative studies for 50 years. SITES 2006 is the fifth wave of surveys related to information and communication technology (ICT), a wave that IEA started with its Computers in Education Study (two studies with data collection in 1989 and 1992),…

  8. RESIDENTIAL WOOD COMBUSTION TECHNOLOGY REVIEW VOLUME 1. TECHNICAL REPORT

    Science.gov (United States)

    This report gives results of a review of the current state-of-the-art of residential wood combustion (RWC). The key environmental parameter of concern was the air emission of particles. The technological status of all major RWC categories -- cordwood stoves, fireplaces, masonry h...

  9. Annual meeting on nuclear technology '92. Technical session 'Nuclear energy discussion'

    International Nuclear Information System (INIS)

    1992-05-01

    The report contains the six special papers red at the 1992 annual conference on nuclear engineering at Karlsruhe, all of which are individually retrievable from the database. They deal with the following subjects: historical development of the basic trends of technology criticism; communication problems in connection with the conveying of technical facts; psycho-sociological patterns of technology anxiety-mental infection or risk consciousness; field of tension between technology and journalism; handling of insecurities; ethical justifiability of nuclear energy use. (HSCH) [de

  10. Technical assistance and the transfer of remote sensing technology. [for economic development

    Science.gov (United States)

    Chipman, R.

    1977-01-01

    The transfer of technology from industrialized countries to the third world is a very complicated process and one that requires a great deal of research and development. The political and social obstacles to this transfer are generally greater than the technical obstacles, but technical assistance programs have neither the competence nor the inclination to deal with these factors adequately. Funding for technical assistance in remote sensing is now expanding rapidly, and there is a growing need for institutions to study and promote the effective use of this technology for economic development. The United Nations, the Food and Agriculture Organization, the World Bank, the United States Agency for International Development and the Canadian technical assistance agencies take different approaches to the problem and deal with the political pressures in different ways.

  11. Technology of perfection to technical tactical preparedness of skilled footballers in microcycles of competition period.

    Directory of Open Access Journals (Sweden)

    Doroshenko E.Y.

    2012-04-01

    Full Text Available Technology of perfection to technical tactical to preparedness of skilled footballers in the microcycles of preparation of competition process is considered. It is shown that for development of this technology key positions of general theory of preparation of sportsmen are used in Olympic and professional sport and technical tactical actions of players taking into account the internal and external parameters of the physical loading. Information of training process of footballers of youth composition of command «Metallurgist» (Zaporozhia is utillized in research. It is analysed and generalized information of complex scientific group. The program of perfection of technical and tactical preparedness is developed. It is set that the use of this program will allow to optimize individual, group and command technical tactical preparedness of skilled footballers on the basis of account of parameters of playing actions and factors, детерминирующих a physical capacity.

  12. Software Technology for Adaptable, Reliable Systems (STARS) Technical Program Plan,

    Science.gov (United States)

    1986-08-06

    Shadow projects that are being considered by the SEI: Service Project Company . . Army FATDS Magnavox CSS To Be Determined PLRS Hughes Navy BSY-I IBM...ISCS Rockwell ACDS Hughes Air Force Simulators Boeing CSSR GTE ATF Grumman MILSTAR Lockheed Figure 4-2 Candidate FY 1986 Shadow Projects 4.2.3 SHADOW...Journal of the Armed Forces Communications and Electronic Association, September 1985. 11. Schill, J., Smeaton, R., and Jackman , R., The Conversion of

  13. Development of broadband free electron laser technology

    International Nuclear Information System (INIS)

    Lee, B. C.; Jeong, Y. W.; Joe, S. O.; Park, S. H.; Ryu, J. K.; Kazakevich, G.; Cha, H. J.; Sohn, S. C.; Han, S. J.

    2003-02-01

    Layer cladding technology was developed to mitigate the fretting wear damages occurred at fuel spacers in Hanaro reactor. The detailed experimental procedures are as follows. 1) Analyses of fretting wear damages and fabrication process of fuel spacers 2) Development and analysis of spherical Al 6061 T-6 alloy powders for the laser cladding 3) Analysis of parameter effects on laser cladding process for clad bids, and optimization of laser cladding process 4) Analysis on the changes of cladding layers due to overlapping factor change 5) Microstructural observation and phase analysis 6) Characterization of materials properties (hardness wear tests) 7) Development of a vision system and revision of its related software 8) Manufacture of prototype fuel spacers. As a result, it was confirmed that the laser cladding technology could increased considerably the wear resistance of Al 6061 alloy which is the raw material of fuel spacers.

  14. Information Technology in project-organized electronic and computer technology engineering education

    DEFF Research Database (Denmark)

    Nielsen, Kirsten Mølgaard; Nielsen, Jens Frederik Dalsgaard

    1999-01-01

    This paper describes the integration of IT in the education of electronic and computer technology engineers at Institute of Electronic Systems, Aalborg Uni-versity, Denmark. At the Institute Information Technology is an important tool in the aspects of the education as well as for communication...

  15. RE/SPEC Inc. technical support to the Repository Technology Program

    International Nuclear Information System (INIS)

    Wagner, R.A.

    1992-06-01

    This report presents a summary of all RE/SPEC Inc. technical support activities to the Repository Technology Program (RTP) from September 1, 1988, through June 30, 1992. The RE/SPEC Inc. activities are grouped into the following categories: project management, project quality assurance (QA), performance assessment (PA), support of the Office of Civilian Radioactive Waste Management (OCRWM) through technical reviews and general assistance, participation in the Department of Energy (DOE) International Program, and code evaluation and documentation

  16. Results of the activities of the Scientific and Technical Coordination Council for Radiation Technique and Technology

    Energy Technology Data Exchange (ETDEWEB)

    Sille, A K [Gosudarstvennyj Komitet po Ispol' zovaniyu Atomnoj Ehnergii SSSR, Moscow

    1977-03-01

    It is reported on the activities of the Scientific and Technical Coordination Council for Radiation Technique and Technology (STCC-RTT) of the CMEA Permanent Commission for the Peaceful Uses of Atomic Energy according to the programme 1971 to 1975. The STCC-RTT is concerned with technical applications such as radiation sterilization, food irradiation, radiation-induced chemical processes etc. The main tasks which have to be solved within the period from 1976 to 1980 are outlined.

  17. The final technical report of the CRADA, 'Medical Accelerator Technology'

    International Nuclear Information System (INIS)

    Chu, W.T.; Rawls, J.M.

    2000-01-01

    Under this CRADA, Berkeley Lab and the industry partner, General Atomics (GA), have cooperatively developed hadron therapy technologies for commercialization. Specifically, Berkeley Lab and GA jointly developed beam transport systems to bring the extracted protons from the accelerator to the treatment rooms, rotating gantries to aim the treatment beams precisely into patients from any angle, and patient positioners to align the patient accurately relative to the treatment beams. We have also jointly developed a patient treatment delivery system that controls the radiation doses in the patient, and hardware to improve the accelerator performances, including a radio-frequency ion source and its low-energy beam transport (LEBT) system. This project facilitated the commercialization of the DOE-developed technologies in hadron therapy by the private sector in order to improve the quality of life of the nation

  18. Biopower Technical Assessment: State of the Industry and the Technology

    Energy Technology Data Exchange (ETDEWEB)

    Bain, R. L.; Amos, W. P.; Downing, M.; Perlack, R. L.

    2003-01-01

    This report provides an assessment of the state of the biopower industry and the technology for producing electricity and heat from biomass. Biopower (biomass-to-electricity generation), a proven electricity generating option in the United States and with about 11 GW of installed capacity, is the single largest source of non-hydro renewable electricity. This 11 GW of capacity encompasses about 7.5 GW of forest product industry and agricultural industry residues, about 3.0 GW of municipal solid waste-based generating capacity and 0.5 GW of other capacity such as landfill gas based production. The electricity production from biomass is being used and is expected to continue to be used as base load power in the existing electrical distribution system. An overview of sector barriers to biopower technology development is examined in Chapter 2. The discussion begins with an analysis of technology barriers that must be overcome to achieve successful technology pathways leading to the commercialization of biomass conversion and feedstock technologies. Next, an examination of institutional barriers is presented which encompasses the underlying policies, regulations, market development, and education needed to ensure the success of biopower. Chapter 3 summarizes biomass feedstock resources, characteristics, availability, delivered prices, requirements for processing, and the impediments and barriers to procurement. A discussion of lessons learned includes information on the California biomass energy industry, lessons from commercial biopower plants, lessons from selected DOE demonstration projects, and a short summary of the issues considered most critical for commercial success is presented in Chapter 4. A series of case studies, Chapter 5, have been performed on the three conversion routes for Combined Heat and Power (CHP) applications of biomass--direct combustion, gasification, and cofiring. The studies are based on technology characterizations developed by NREL and EPRI

  19. Technical analysis of US Army Weapons Systems and related advanced technologies of military interest. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-06-14

    This report summarizes the activities and accomplishments of an US Army technology security project designed to identify and develop effective policy guidelines for militarily critical technologies in specific Army systems and in broad generic technology areas of military interest, Individual systems analyses are documented in separate Weapons Systems Technical Assessments (WSTAs) and the general generic technology areas are evaluated in the Advanced Technology Assessment Reports (ATARs), However, specific details of these assessments are not addressed here, only recommendations regarding aspects of the defined approach, methodology, and format are provided and discussed.

  20. Flexible Assembly Solar Technology (FAST) Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Toister, Elad [BrightSource Energy Inc., Jerusalem (Israel)

    2014-11-06

    The Flexible Assembly Solar Technology (FAST) project was initiated by BrightSource in an attempt to provide potential solar field EPC contractors with an effective set of tools to perform specific construction tasks. These tasks are mostly associated with heliostat assembly and installation, and require customized non-standard tools. The FAST concept focuses on low equipment cost, reduced setup time and increased assembly throughput as compared to the Ivanpah solar field construction tools.

  1. Nuclear engineering and manufacturing technology transfer coproduction with technical assistance

    International Nuclear Information System (INIS)

    Marillier, J.C.; Boury, C.

    1985-10-01

    This paper emphasizes in the specific areas of design, engineering, and component production. This paper presents what Framatome has to offer in these areas and its export oriented philosophy. Then, a typical example of successful implementation of this technology transfer philosophy is the collaboration with the South Korean firm, Korea Heavy Industries Corporation (KHIC) for the supply of KNU 9 and KNU 10 power stations

  2. Technical Training Seminar: Laser Trackers: the Local Positioning Technology (LPT)

    CERN Document Server

    Davide Vitè

    2005-01-01

    Friday 20 May from 10:00 to 16:00, Training Centre (bldg. 593) Laser Trackers: the Local Positioning Technology (LPT) Simon Moser, Michael Lettau, Achim Lupus, Niklaus Suter, Leica GEOSYSTEMS AG, Switzerland Laser trackers are used at CERN for different applications within the LHC Project. Leica Geosystems AG have been developing during the last four years the revolutionary Local Positioning Technology (LPT). Laser trackers are increasingly used to ensure accuracy of large fabrications, and alignment in the final assembly process. Competing portable Coordinate Measuring Machines (CMM) with articulated arms require a frequent repositioning, known to lead to a loss of accuracy and efficiency. Leica Geosystems developed armless solutions, the T-Probe and T-Scan, for use with its laser trackers. The combination of the tracker technology with photogrammetry is the base of LPT, enabling real time measurements with free hand-held devices, such as the T-Probe and T-Scan. T-Probe and T-Scan overcome the proble...

  3. TECHNOLOGY FOR DEVELOPMENT OF ELECTRONIC TEXTBOOK ON HANDICRAFTS METHODOLOGY

    Directory of Open Access Journals (Sweden)

    Iryna V. Androshchuk

    2017-10-01

    Full Text Available The main approaches to defining the concept of electronic textbook have been analyzed in the article. The main advantages of electronic textbooks in the context of future teachers’ training have been outlined. They are interactivity, feedback provision, availability of navigation and search engine. The author has presented and characterized the main stages in the technology of development of an electronic textbook on Handicraft and Technology Training Methodology: determination of its role and significance in the process of mastering the discipline; justification of its structure; outline of the stages of its development in accordance with the defined structure. The characteristic feature of the developed electronic textbook is availability of macro- and microstructure. Macrostructure is viewed as a sequence of components of the electronic textbook that are manifested in its content; microstructure is considered to be an internal pattern of each component of macrostructure.

  4. Small compact pulsed electron source for radiation technologies

    International Nuclear Information System (INIS)

    Korenev, Sergey

    2002-01-01

    The small compact pulsed electron source for radiation technologies is considered in the report. The electron source consists of pulsed high voltage Marx generator and vacuum diode with explosive emission cathode. The main parameters of electron source are next: kinetic energy is 100-150 keV, beam current is 5-200 A and pulse duration is 100-400 nsec. The distribution of absorbed doses in irradiated materials is considered. The physical feasibility of pulsed low energy electron beam for applications is considered

  5. Final Technical Report. Training in Building Audit Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Brosemer, Kathleen [Sault Sainte Marie Tribe of Chippewa Indians, Marie, MI (United States)

    2015-03-27

    In 2011, the Tribe proposed and was awarded the Training in Building Audit Technologies grant from the DOE in the amount of $55,748 to contract for training programs for infrared cameras, blower door technology applications and building systems. The coursework consisted of; Infrared Camera Training: Level I - Thermal Imaging for Energy Audits; Blower Door Analysis and Building-As-A-System Training, Building Performance Institute (BPI) Building Analyst; Building Envelope Training, Building Performance Institute (BPI) Envelope Professional; and Audit/JobFLEX Tablet Software. Competitive procurement of the training contractor resulted in lower costs, allowing the Tribe to request and receive DOE approval to additionally purchase energy audit equipment and contract for residential energy audits of 25 low-income Tribal Housing units. Sault Tribe personnel received field training to supplement the classroom instruction on proper use of the energy audit equipment. Field experience was provided through the second DOE energy audits grant, allowing Sault Tribe personnel to join the contractor, Building Science Academy, in conducting 25 residential energy audits of low-income Tribal Housing units.

  6. Conserving energy through new irrigation technologies. Technical briefing report

    Energy Technology Data Exchange (ETDEWEB)

    1982-07-01

    The benefits and applications of five irrigation technologies are explored: mobile drop-tube irrigation, computerized scheduling, reduced-pressure center pivots, well design and development, and automated gated-pipe systems. Perhaps the most promising of the new irrigation technologies is the low-energy, precision-application (LEPA) system. This mobile system used one-half the energy of conventional sprinkler systems and distributes water with greater efficiency through a series of low-pressure drop tubes suspended above the crop. Computerized methods of irrigation scheduling have been developed to help farmers conserve water and energy. Special computer programs determine when a crop needs water and how much to apply for optimal plant growth, thus preventing the unnecessary costs of pumping more water than the crop needs. Field test results show that replacing traditional scheduling methods of irrigation with computerized scheduling can reduce energy and water use by as much as 35%. The irrigation industry is actively promoting reduced-pressure water application methods, particularly for center-pivot systems. Reduced-pressure systems expend less energy but produce the same crop yields as conventional high-pressure systems, as long as excessive water runoff does not occur. If well design and development techniques are applied when a well is drilled into an unconsolidated acquifer, the well's life expectancy, as well as its operating efficiency, can increase, the later by as much as 40%.

  7. Nuclear technology education at the new AKR-2 of the technical university Dresden

    International Nuclear Information System (INIS)

    Hansen, W.; Wolf, T.; Hurtado, A.

    2009-01-01

    The former research and training reactor AKR-1 was completely renewed, including the peripheral technical systems and the modernization of the reactor instrumentation with digital control technology. After licensing by the local authorities the technical University Dresden has Germany's latest training reactor. Basic experiments are performed for the following disciplines: nuclear energy technology, physics, teacher training, industrial engineering, nuclear medicine. Training courses cover nuclear medicine, nuclear physics, radiation protection and reactor physics. Further tasks include research program on neutron detectors, neutron physics, radiation spectroscopy, nuclear data bases.

  8. Technical cooperation for the pacific uses of nuclear technology in Latin America and Caribbean: the experience of regional agreement ARCAL

    International Nuclear Information System (INIS)

    Rondinelli Junior, Francisco

    2017-01-01

    This thesis studies the international technical cooperation in the field of peaceful applications of the nuclear technology, focusing on the experience of Latin American countries, where the Cooperation Agreement for the Promotion of Nuclear Science and Technology in Latin America and the Caribbean, also known as ARCAL, is in force. The study adopts as theoretical approach the concept of state capacities, particularly with regard to the institutional capacities applicable to the ARCAL Agreement. Within this approach, three dimensions of analysis are adopted: the institutional dimension, the governance dimension and the focus on outcomes. The evaluation of the ARCAL Agreement is carried out in order to confirm if the intended role to promote regional technical cooperation in the nuclear sector is being implemented. The methodological approach adopted the case study model. It starts with the analysis of the institutional evolution of the Agreement, and identifies variables articulating with the three dimensions above mentioned. The empirical data were collected in two stages. In the first stage it were performed 29 interviews carried out by the author with the technical and staff members of the Department of Technical Cooperation of IAEA, in Vienna, Austria, headquarter of IAEA. The other stage involved an electronic questionnaire submitted to the national coordinator of ARCAL in 14 countries, in a universe of 21 member states. The conclusion of the research points to the fact that the ARCAL Agreement has incorporated, throughout its trajectory, elements of the institutional capacities which are still in the process of development. They give to the Agreement the potential to induce the development of the state capacities of the respective countries in the field of peaceful applications of nuclear technology. (author)

  9. Massachusetts Institute of Technology, Plasma Fusion Center, technical research programs

    International Nuclear Information System (INIS)

    1982-02-01

    Research programs have produced significant results on four fronts: (1) the basic physics of high-temperature fusion plasmas (plasma theory, RF heating, development of advanced diagnostics and small-scale experiments on the Versator tokamak and Constance mirror devices); (2) major confinement results on the Alcator A and C tokamaks, including pioneering investigations of the equilibrium, stability, transport and radiation properties of fusion plasmas at high densities, temperatures and magnetic fields; (3) development of a new and innovative design for axisymmetric tandem mirrors with inboard thermal barriers, with initial operation of the TARA tandem mirror experimental facility scheduled for 1983; and (4) a broadly based program of fusion technology and engineering development that addresses problems in several critical subsystem areas

  10. Annual meeting on nuclear technology '96. Technical session: Energy costs

    International Nuclear Information System (INIS)

    1996-08-01

    The two papers of this session deal with the costs of two different energy generation systems, one is based on photovoltaic energy conversion, and the other is the nuclear fuel cycle and nuclear energy generation. The author shows that the costs of these two energy systems in Germany are much more governed by decisions taken in the political domain than is the case in other countries. Although German science and technology in these two engineering fields hold a top rank worldwide, the high costs that seem inevitable in Germany are expected to be a major reason why the photovoltaic industry will have to leave the country and go abroad to exploit the better chances there. (DG) [de

  11. DO Get Technical! Using Technology in Library Instruction

    Directory of Open Access Journals (Sweden)

    Nicole Eva

    2011-12-01

    Full Text Available Today’s post-secondary students are digital natives. Much has been said and written about how to reach this generation, and the consensus seems to be that we need to meet them on their turf. In this session presented at WILU 2011 in Regina, SK, two librarians from the University of Lethbridge shared their experiences with using technology to engage students in library instruction. The hands-on session introduced some simple tools librarians can learn quickly and apply to spice up their instruction with technology. These include creating online animated videos using Xtranormal, a low-cost tool way to create polished and humourous videos to introduce or summarize key information literacy concepts; and adding interactive polling to PowerPoint presentations using a tool called Poll Everywhere, which is an effective way to instantly engage students in instruction using the web or web-enabled devices. Interactive polling eliminates many of the challenges of using clickers which are prevalent in many post-secondary library instruction environments. The presenters also discussed how they have experimented with wikis to encourage active learning and student collaboration in a series of library instruction sessions. Wikis allow for free and paperless student participation in knowledge creation in an online forum. Finally, they demonstrated how they have used Skype to deliver library instruction at a distance, including the use of the screen sharing feature. The presenters stressed the ease of use of these free or low-cost tools to improve classroom engagement and add interest to sessions.

  12. Control and diagnostics of technical state of main electro technical and thermal equipment of NPP, TPS and HPS on the basis of thermovision technologies

    International Nuclear Information System (INIS)

    Banduryan, B.B.; Fedorenko, G.M.; Ostapchuk, L.B.; Saratov, V.O.

    2006-01-01

    The opportunity of using of thermovision technologies for detection of defects NPP, TPS and HPS electro technical and power equipment is shown. The results of thermovision monitoring of a turbine generator stator technical state are represented. The method for thermovision control of a technical state of a electrical machines and apparatus construction elements, for which the patent of Ukraine have been obtained, is described. he verification of the offered expedient thermovision control and diagnostics at 'Elektrovazhmash' factory was carried out

  13. Electronic Communities: a Forum for Supporting Women Professionals and Students in Technical and Scientific Fields

    Science.gov (United States)

    Single, Peg Boyle; Muller, Carol B.; Cunningham, Christine M.; Single, Richard M.

    In this article, we report on electronic discussion lists (e-lists) sponsored by MentorNet, the National Electronic Industrial Mentoring Network for Women in Engineering and Science. Using the Internet, the MentorNet program connects students in engineering and science with mentors working in industry. These e-lists are a feature of MentorNet's larger electronic mentoring program and were sponsored to foster the establishment of community among women engineering and science students and men and women professionals in those fields. This research supports the hypothesis that electronic communications can be used to develop community among engineering and science students and professionals and identifies factors influencing the emergence of electronic communities (e-communities). The e-lists that emerged into self-sustaining e-communities were focused on topic-based themes, such as balancing personal and work life, issues pertaining to women in engineering and science, and job searching. These e-communities were perceived to be safe places, embraced a diversity of opinions and experiences, and sanctioned personal and meaningful postings on the part of the participants. The e-communities maintained three to four simultaneous threaded discussions and were sustained by professionals who served as facilitators by seeding the e-lists with discussion topics. The e-lists were sponsored to provide women students participating in MentorNet with access to groups of technical and scientific professionals. In addition to providing benefits to the students, the e-lists also provided the professionals with opportunities to engage in peer mentoring with other, mostly female, technical and scientific professionals. We discuss the implications of our findings for developing e-communities and for serving the needs of women in technical and scientific fields.

  14. The socio-technical organisation of community pharmacies as a factor in the Electronic Prescription Service Release Two implementation: a qualitative study

    Science.gov (United States)

    2012-01-01

    Background The introduction of a new method of transmitting prescriptions from general practices to community pharmacies in England (Electronic Prescription Service Release 2 (EPS2)) has generated debate on how it will change work practice. As EPS2 will be a key technical element in dispensing, we reviewed the literature to find that there were no studies on how social and technical elements come together to form work practice in community pharmacies. This means the debate has little point of reference. Our aim therefore was to study the ways social and technical elements of a community pharmacy are used to achieve dispensing through the development of a conceptual model on pharmacy work practice, and to consider how a core technical element such the EPS2 could change work practice. Method We used ethnographic methods inclusive of case-study observations and interviews to collect qualitative data from 15 community pharmacies that were in the process of adopting or were soon to adopt EPS2. We analysed the case studies thematically and used rigorous multi-dimensional and multi-disciplinary interpretive validation techniques to cross analyse findings. Results In practice, dispensing procedures were not designed to take into account variations in human and technical integration, and assumed that repetitive and collective use of socio-technical elements were at a constant. Variables such as availability of social and technical resources, and technical know-how of staff were not taken into account in formalised procedures. Yet community pharmacies were found to adapt their dispensing in relation to the balance of social and technical elements available, and how much of the social and technical elements they were willing to integrate into dispensing. While some integrated as few technical elements as possible, some depended entirely on technical artefacts. This pattern also applied to the social elements of dispensing. Through the conceptual model development process, we

  15. The socio-technical organisation of community pharmacies as a factor in the Electronic Prescription Service Release Two implementation: a qualitative study.

    Science.gov (United States)

    Harvey, Jasmine; Avery, Anthony J; Waring, Justin; Barber, Nick

    2012-12-20

    The introduction of a new method of transmitting prescriptions from general practices to community pharmacies in England (Electronic Prescription Service Release 2 (EPS2)) has generated debate on how it will change work practice. As EPS2 will be a key technical element in dispensing, we reviewed the literature to find that there were no studies on how social and technical elements come together to form work practice in community pharmacies. This means the debate has little point of reference. Our aim therefore was to study the ways social and technical elements of a community pharmacy are used to achieve dispensing through the development of a conceptual model on pharmacy work practice, and to consider how a core technical element such the EPS2 could change work practice. We used ethnographic methods inclusive of case-study observations and interviews to collect qualitative data from 15 community pharmacies that were in the process of adopting or were soon to adopt EPS2. We analysed the case studies thematically and used rigorous multi-dimensional and multi-disciplinary interpretive validation techniques to cross analyse findings. In practice, dispensing procedures were not designed to take into account variations in human and technical integration, and assumed that repetitive and collective use of socio-technical elements were at a constant. Variables such as availability of social and technical resources, and technical know-how of staff were not taken into account in formalised procedures. Yet community pharmacies were found to adapt their dispensing in relation to the balance of social and technical elements available, and how much of the social and technical elements they were willing to integrate into dispensing. While some integrated as few technical elements as possible, some depended entirely on technical artefacts. This pattern also applied to the social elements of dispensing. Through the conceptual model development process, we identified three

  16. Technology status in support of refined technical baseline for the Spent Nuclear Fuel project. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Puigh, R.J.; Toffer, H.; Heard, F.J.; Irvin, J.J.; Cooper, T.D.

    1995-10-20

    The Spent Nuclear Fuel Project (SNFP) has undertaken technology acquisition activities focused on supporting the technical basis for the removal of the N Reactor fuel from the K Basins to an interim storage facility. The purpose of these technology acquisition activities has been to identify technology issues impacting design or safety approval, to establish the strategy for obtaining the necessary information through either existing project activities, or the assignment of new work. A set of specific path options has been identified for each major action proposed for placing the N Reactor fuel into a ``stabilized`` form for interim storage as part of this refined technical basis. This report summarizes the status of technology information acquisition as it relates to key decisions impacting the selection of specific path options. The following specific categories were chosen to characterize and partition the technology information status: hydride issues and ignition, corrosion, hydrogen generation, drying and conditioning, thermal performance, criticality and materials accountability, canister/fuel particulate behavior, and MCO integrity. This report represents a preliminary assessment of the technology information supporting the SNFP. As our understanding of the N Reactor fuel performance develops the technology information supporting the SNFP will be updated and documented in later revisions to this report. Revision 1 represents the incorporation of peer review comments into the original document. The substantive evolution in our understanding of the technical status for the SNFP (except section 3) since July 1995 have not been incorporated into this revision.

  17. Technology status in support of refined technical baseline for the Spent Nuclear Fuel project. Revision 1

    International Nuclear Information System (INIS)

    Puigh, R.J.; Toffer, H.; Heard, F.J.; Irvin, J.J.; Cooper, T.D.

    1995-01-01

    The Spent Nuclear Fuel Project (SNFP) has undertaken technology acquisition activities focused on supporting the technical basis for the removal of the N Reactor fuel from the K Basins to an interim storage facility. The purpose of these technology acquisition activities has been to identify technology issues impacting design or safety approval, to establish the strategy for obtaining the necessary information through either existing project activities, or the assignment of new work. A set of specific path options has been identified for each major action proposed for placing the N Reactor fuel into a ''stabilized'' form for interim storage as part of this refined technical basis. This report summarizes the status of technology information acquisition as it relates to key decisions impacting the selection of specific path options. The following specific categories were chosen to characterize and partition the technology information status: hydride issues and ignition, corrosion, hydrogen generation, drying and conditioning, thermal performance, criticality and materials accountability, canister/fuel particulate behavior, and MCO integrity. This report represents a preliminary assessment of the technology information supporting the SNFP. As our understanding of the N Reactor fuel performance develops the technology information supporting the SNFP will be updated and documented in later revisions to this report. Revision 1 represents the incorporation of peer review comments into the original document. The substantive evolution in our understanding of the technical status for the SNFP (except section 3) since July 1995 have not been incorporated into this revision

  18. Definition of technology development missions for early Space Station satellite servicing. Volume 2: Technical

    Science.gov (United States)

    Cable, D. A.; Diewald, C. A.; Hills, T. C.; Parmentier, T. J.; Spencer, R. A.; Stone, G. E.

    1984-01-01

    Volume 2 contains the Technical Report of the approach and results of the Phase 2 study. The phase 2 servicing study was initiated in June 1983, and is being reported in this document. The scope of the contract was to: (1) define in detail five selected technology development missions (TDM); (2) conduct a design requirement analysis to refine definitions of satellite servicing requirements at the space station; and (3) develop a technology plan that would identify and schedule prerequisite precursor technology development, associated. STS flight experiments and space station experiments needed to provide onorbit validation of the evolving technology.

  19. Technical Reviews on Pattern Recognition in Process Analytical Technology

    International Nuclear Information System (INIS)

    Kim, Jong Yun; Choi, Yong Suk; Ji, Sun Kyung; Park, Yong Joon; Song, Kyu Seok; Jung, Sung Hee

    2008-12-01

    Pattern recognition is one of the first and the most widely adopted chemometric tools among many active research area in chemometrics such as design of experiment(DoE), pattern recognition, multivariate calibration, signal processing. Pattern recognition has been used to identify the origin of a wine and the time of year that the vine was grown by using chromatography, cause of fire by using GC/MS chromatography, detection of explosives and land mines, cargo and luggage inspection in seaports and airports by using a prompt gamma-ray activation analysis, and source apportionment of environmental pollutant by using a stable isotope ratio mass spectrometry. Recently, pattern recognition has been taken into account as a major chemometric tool in the so-called 'process analytical technology (PAT)', which is a newly-developed concept in the area of process analytics proposed by US Food and Drug Administration (US FDA). For instance, identification of raw material by using a pattern recognition analysis plays an important role for the effective quality control of the production process. Recently, pattern recognition technique has been used to identify the spatial distribution and uniformity of the active ingredients present in the product such as tablet by transforming the chemical data into the visual information

  20. Technical Data Management Center: a focal point for meteorological and other environmental transport computing technology

    International Nuclear Information System (INIS)

    McGill, B.; Maskewitz, B.F.; Trubey, D.K.

    1981-01-01

    The Technical Data Management Center, collecting, packaging, analyzing, and distributing information, computer technology and data which includes meteorological and other environmental transport work is located at the Oak Ridge National Laboratory, within the Engineering Physics Division. Major activities include maintaining a collection of computing technology and associated literature citations to provide capabilities for meteorological and environmental work. Details of the activities on behalf of TDMC's sponsoring agency, the US Nuclear Regulatory Commission, are described

  1. An Assessment of the Technical Readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR) Technology

    Science.gov (United States)

    Flynn, Michael

    2000-01-01

    This poster provides an assessment of the technical readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR). The VPCAR technology is a fully regenerative water recycling technology designed specifically for applications such as a near term Mars exploration mission. The VPCAR technology is a highly integrated distillation/catalytic oxidation based water processor. It is designed to accept a combined wastewater stream (urine, condensate, and hygiene) and produces potable water in a single process step which requires -no regularly scheduled re-supply or maintenance for a 3 year mission. The technology is designed to be modular and to fit into a volume comparable to a single International Space Station Rack (when sized for a crew of 6). This poster provides a description of the VPCAR technology and a summary of the current performance of the technology. Also provided are the results of two separate NASA sponsored system trade studies which investigated the potential payback of further development of the VPCAR technology.

  2. Endoscopic and keyhole endoscope-assisted neurosurgical approaches: a qualitative survey on technical challenges and technological solutions.

    Science.gov (United States)

    Marcus, Hani J; Cundy, Thomas P; Hughes-Hallett, Archie; Yang, Guang-Zhong; Darzi, Ara; Nandi, Dipankar

    2014-10-01

    The literature reflects a resurgence of interest in endoscopic and keyhole endoscope-assisted neurosurgical approaches as alternatives to conventional microsurgical approaches in carefully selected cases. The aim of this study was to assess the technical challenges of neuroendoscopy, and the scope for technological innovations to overcome these barriers. All full members of the Society of British Neurosurgeons (SBNS) were electronically invited to participate in an online survey. The open-ended structured survey asked three questions; firstly, whether the surgeon presently utilises or has experience with endoscopic or endoscope-assisted approaches; secondly, what they consider to be the major technical barriers to adopting such approaches; and thirdly, what technological advances they foresee improving safety and efficacy in the field. Responses were subjected to a qualitative research method of multi-rater emergent theme analysis. Three clear themes emerged: 1) surgical approach and better integration with image-guidance systems (20%), 2) intra-operative visualisation and improvements in neuroendoscopy (49%), and 3) surgical manipulation and improvements in instruments (74%). The analysis of responses to our open-ended survey revealed that although opinion was varied three major themes could be identified. Emerging technological advances such as augmented reality, high-definition stereo-endoscopy, and robotic joint-wristed instruments may help overcome the technical difficulties associated with neuroendoscopic approaches. Results of this qualitative survey provide consensus amongst the technology end-user community such that unambiguous goals and priorities may be defined. Systems integrating these advances could improve the safety and efficacy of endoscopic and endoscope-assisted neurosurgical approaches.

  3. Technical, environmental, and economic assessment of deploying advanced coal power technologies in the Chinese context

    International Nuclear Information System (INIS)

    Zhao Lifeng; Xiao Yunhan; Gallagher, Kelly Sims; Wang Bo; Xu Xiang

    2008-01-01

    The goal of this study is to evaluate the technical, environmental, and economic dimensions of deploying advanced coal-fired power technologies in China. In particular, we estimate the differences in capital cost and overall cost of electricity (COE) for a variety of advanced coal-power technologies based on the technological and economic levels in 2006 in China. This paper explores the economic gaps between Integrated Gasification Combined Cycle (IGCC) and other advanced coal power technologies, and compares 12 different power plant configurations using advanced coal power technologies. Super critical (SC) and ultra super critical (USC) pulverized coal (PC) power generation technologies coupled with pollution control technologies can meet the emission requirements. These technologies are highly efficient, technically mature, and cost-effective. From the point of view of efficiency, SC and USC units are good choices for power industry. The net plant efficiency for IGCC has reached 45%, and it has the best environmental performance overall. The cost of IGCC is much higher, however, than that of other power generation technologies, so the development of IGCC is slow throughout the world. Incentive policies are needed if IGCC is to be deployed in China

  4. Flexible technology for Electronics: Its Derivatives and Possibilities

    OpenAIRE

    Deovrat Phal; Akshay Narkar

    2014-01-01

    With the inkjet printing technology becoming more popular, integration of circuits developed on flexible substrates which are easily embedded inside the machine as against the rigid PCB circuits is becoming more prevalent. Much of the research has been done in applications of such circuits in human body implants or for other low cost applications. This paper concentrates particularly on applications of such circuits in the field of consumer electronics, disposable electronics,...

  5. Allocating Spending Between Advertising and Information Technology in Electronic Retailing

    OpenAIRE

    Yong Tan; Vijay S. Mookerjee

    2005-01-01

    This study examines coordination issues that occur in allocating spending between advertising and information technology (IT) in electronic retailing. Electronic retailers run the risk of overspending on advertising to attract customers but underspending on IT, thus resulting in inadequate processing capacity at the firm's website. In this paper, we present a centralized, joint marketing-IT model to optimally allocate spending between advertising and IT, and we discuss an uncoordinated case w...

  6. Managing electronic records methods, best practices, and technologies

    CERN Document Server

    Smallwood, Robert F

    2013-01-01

    The ultimate guide to electronic records management, featuring a collaboration of expert practitioners including over 400 cited references documenting today's global trends, standards, and best practices Nearly all business records created today are electronic, and are increasing in number at breathtaking rates, yet most organizations do not have the policies and technologies in place to effectively organize, search, protect, preserve, and produce these records. Authored by an internationally recognized expert on e-records in collaboration with leading subject matter experts worldwide

  7. Advances in electronic-nose technologies developed for biomedical applications.

    Science.gov (United States)

    Wilson, Alphus D; Baietto, Manuela

    2011-01-01

    The research and development of new electronic-nose applications in the biomedical field has accelerated at a phenomenal rate over the past 25 years. Many innovative e-nose technologies have provided solutions and applications to a wide variety of complex biomedical and healthcare problems. The purposes of this review are to present a comprehensive analysis of past and recent biomedical research findings and developments of electronic-nose sensor technologies, and to identify current and future potential e-nose applications that will continue to advance the effectiveness and efficiency of biomedical treatments and healthcare services for many years. An abundance of electronic-nose applications has been developed for a variety of healthcare sectors including diagnostics, immunology, pathology, patient recovery, pharmacology, physical therapy, physiology, preventative medicine, remote healthcare, and wound and graft healing. Specific biomedical e-nose applications range from uses in biochemical testing, blood-compatibility evaluations, disease diagnoses, and drug delivery to monitoring of metabolic levels, organ dysfunctions, and patient conditions through telemedicine. This paper summarizes the major electronic-nose technologies developed for healthcare and biomedical applications since the late 1980s when electronic aroma detection technologies were first recognized to be potentially useful in providing effective solutions to problems in the healthcare industry.

  8. Advances in Electronic-Nose Technologies Developed for Biomedical Applications

    Directory of Open Access Journals (Sweden)

    Alphus D. Wilson

    2011-01-01

    Full Text Available The research and development of new electronic-nose applications in the biomedical field has accelerated at a phenomenal rate over the past 25 years. Many innovative e-nose technologies have provided solutions and applications to a wide variety of complex biomedical and healthcare problems. The purposes of this review are to present a comprehensive analysis of past and recent biomedical research findings and developments of electronic-nose sensor technologies, and to identify current and future potential e-nose applications that will continue to advance the effectiveness and efficiency of biomedical treatments and healthcare services for many years. An abundance of electronic-nose applications has been developed for a variety of healthcare sectors including diagnostics, immunology, pathology, patient recovery, pharmacology, physical therapy, physiology, preventative medicine, remote healthcare, and wound and graft healing. Specific biomedical e-nose applications range from uses in biochemical testing, blood-compatibility evaluations, disease diagnoses, and drug delivery to monitoring of metabolic levels, organ dysfunctions, and patient conditions through telemedicine. This paper summarizes the major electronic-nose technologies developed for healthcare and biomedical applications since the late 1980s when electronic aroma detection technologies were first recognized to be potentially useful in providing effective solutions to problems in the healthcare industry.

  9. Teachers' Views about Technical Education: Implications for Reforms towards a Broad Based Technology Curriculum in Malawi

    Science.gov (United States)

    Chikasanda, Vanwyk Khobidi; Otrel-Cass, Kathrin; Jones, Alister

    2011-01-01

    Internationally there has been concern about the direction of technical education and how it is positioned in schools. This has also been the case in Malawi where the curriculum has had a strong focus on skills development. However, lately there has been a call for enhancing technological literacy of students, yet little support has been provided…

  10. Standards for Technological Literacy and STEM Education Delivery through Career and Technical Education Programs

    Science.gov (United States)

    Asunda, Paul A.

    2012-01-01

    At a minimum, employers rely on career and technical education (CTE) and workforce training systems to supply workers able to perform in their jobs. In CTE classes that seek to integrate science, technology, engineering, and mathematics (STEM) concepts, it falls to the instructors to design and sequence the learning experiences that will promote…

  11. The Relationship between Return on Profitability and Costs of Outsourcing Information Technology Technical Support

    Science.gov (United States)

    Odion, Segun

    2011-01-01

    The purpose of this quantitative correlational research study was to examine the relationship between costs of operation and total return on profitability of outsourcing information technology technical support in a two-year period of outsourcing operations. United States of America list of Fortune 1000 companies' chief information officers…

  12. Marketing Technology. FasTrak Specialization Integrated Technical and Academic Competency (ITAC). Revised.

    Science.gov (United States)

    Ohio State Dept. of Education, Columbus. Div. of Career-Technical and Adult Education.

    This document presents the Ohio Integrated Technical and Academic Competency profile for marketing technology. The profile is to serve as the basis for curriculum development in Ohio's secondary, adult, and postsecondary programs. The profile includes a comprehensive listing of 580 specialty and foundation key indicators for evaluating mastery of…

  13. Advances in heavy water reactor technology. Proceedings of a technical committee meeting

    International Nuclear Information System (INIS)

    1997-11-01

    This IAEA meeting addressed both the status of national programmes and technical topics including advances in plant and system design and new plant features, development of pressure tube technologies, fuel and fuel cycle options, computer code development and verification, and safety and accident analysis

  14. Advanced Technology, a Broad Technical Bachelor Programme at the University of Twente

    NARCIS (Netherlands)

    Flokstra, Jaap; Boukamp, Bernard; Hemmes, Herman; Carvalho, Dinis; van Hattum-Janssen, Natascha; Lima, Rui M.

    2009-01-01

    Advanced Technology is a unique bachelor program at the University of Twente that has a strong multidisciplinary character. The technical component is dominant but is clearly linked to social sciences with emphasis on entrepreneurship. The courses like “Introduction to Engineering” have a leading

  15. Technical attributes, health attribute, consumer attributes and their roles in adoption intention of healthcare wearable technology.

    Science.gov (United States)

    Zhang, Min; Luo, Meifen; Nie, Rui; Zhang, Yan

    2017-12-01

    This paper aims to explore factors influencing the healthcare wearable technology adoption intention from perspectives of technical attributes (perceived convenience, perceived irreplaceability, perceived credibility and perceived usefulness), health attribute (health belief) and consumer attributes (consumer innovativeness, conspicuous consumption, informational reference group influence and gender difference). By integrating technology acceptance model, health belief model, snob effect and conformity and reference group theory, hypotheses and research model are proposed. The empirical investigation (N=436) collects research data through questionnaire. Results show that the adoption intention of healthcare wearable technology is influenced by technical attributes, health attribute and consumer attributes simultaneously. For technical attributes, perceived convenience and perceived credibility both positively affect perceived usefulness, and perceived usefulness influences adoption intention. The relation between perceived irreplaceability and perceived usefulness is only supported by males. For health attribute, health belief affects perceived usefulness for females. For consumer attributes, conspicuous consumption and informational reference group influence can significantly moderate the relation between perceived usefulness and adoption intention and the relation between consumer innovativeness and adoption intention respectively. What's more, consumer innovativeness significantly affects adoption intention for males. This paper aims to discuss technical attributes, health attribute and consumer attributes and their roles in the adoption intention of healthcare wearable technology. Findings may provide enlightenment to differentiate product developing and marketing strategies and provide some implications for clinical medicine. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. A DDC Bibliography on Cost/Benefits of Technical Information Services and Technology Transfer.

    Science.gov (United States)

    Defense Documentation Center, Alexandria, VA.

    This bibliography is a compilation of literature existing in both the government and public sectors and concerning Cost/Benefits of Technical information Services and Technology Transfer. Not only was the cost-benefit to the user reflected, but consideration was given to the initial cost of information collections, the cost of processing the…

  17. Technical Education Outreach in Materials Science and Technology Based on NASA's Materials Research

    Science.gov (United States)

    Jacobs, James A.

    2003-01-01

    The grant NAG-1 -2125, Technical Education Outreach in Materials Science and Technology, based on NASA s Materials Research, involves collaborative effort among the National Aeronautics and Space Administration s Langley Research Center (NASA-LaRC), Norfolk State University (NSU), national research centers, private industry, technical societies, colleges and universities. The collaboration aims to strengthen math, science and technology education by providing outreach related to materials science and technology (MST). The goal of the project is to transfer new developments from LaRC s Center for Excellence for Structures and Materials and other NASA materials research into technical education across the nation to provide educational outreach and strengthen technical education. To achieve this goal we are employing two main strategies: 1) development of the gateway website and 2) using the National Educators Workshop: Update in Engineering Materials, Science and Technology (NEW:Updates). We have also participated in a number of national projects, presented talks at technical meetings and published articles aimed at improving k-12 technical education. Through the three years of this project the NSU team developed the successful MST-Online site and continued to upgrade and update it as our limited resources permitted. Three annual NEW:Updates conducted from 2000 though 2002 overcame the challenges presented first by the September 11,2001 terrorist attacks and the slow U.S. economy and still managed to conduct very effective workshops and expand our outreach efforts. Plans began on NEW:Update 2003 to be hosted by NASA Langley as a part of the celebration of the Centennial of Controlled Flight.

  18. Technology and Power. A Foucauldian Analysis of Electronic Monitoring Discourses

    OpenAIRE

    Anna Vitores; Miquel Domènech

    2007-01-01

    The article aims to show the importance of FOUCAULT within social studies of science and technology. It also illustrates how a Foucauldian analysis can be useful for studies of science, technology and society focused on power effects. To accomplish these objectives we analyze the emergence of a specific techno-scientific innovation: the electronic monitoring of offenders. We map the discontinuities and discourse dispersions linked to those practices that constitute different materializations ...

  19. Spin polarized electron source technology transferred from HE accelerators to electron microscopes

    International Nuclear Information System (INIS)

    Nakanishi, Tsutomu

    2009-01-01

    For many years, we have developed a technology of spin-polarized-electron-source (PES) for a future linear collider project (ILC). Various new techniques for achieving high polarization, high quantum efficiency, high current density, sub-nanosecond multi-bunch generation etc. were developed. Two fundamental technologies; reduction of dark current and preparation of extremely high vacuum environment to protect the Negative Electron Affinity (NEA) surface have been also developed. Using these PES technologies and a new transmission type photocathode, we recently succeeded in producing the high brightness and high polarization electron beam for the low energy electron microscope (LEEM). Our Spin-LEEM system enables the world-first dynamic observation of surface magnetic domain formed by evaporation on the metal substrate with ∼ 20 nm space resolutions. (author)

  20. Technology Corner: Dating of Electronic Hardware for Prior Art Investigations

    Directory of Open Access Journals (Sweden)

    Sellam Ismail

    2012-03-01

    Full Text Available In many legal matters, specifically patent litigation, determining and authenticating the date of computer hardware or other electronic products or components is often key to establishing the item as legitimate evidence of prior art. Such evidence can be used to buttress claims of technologies available or of events transpiring by or at a particular date.In 1945, the Electronics Industry Association published a standard, EIA 476-A, standardized in the reference Source and Date Code Marking (Electronic Industries Association, 1988.(see PDF for full tech corner

  1. Pulsed electron accelerator for radiation technologies in the enviromental applications

    Science.gov (United States)

    Korenev, Sergey

    1997-05-01

    The project of pulsed electron accelerator for radiation technologies in the environmental applications is considered. An accelerator consists of high voltage generator with vacuum insulation and vacuum diode with plasma cathode on the basis discharge on the surface of dielectric of large dimensions. The main parameters of electron accelerators are following: kinetic energy 0.2 - 2.0 MeV, electron beam current 1 - 30 kA and pulse duration 1- 5 microseconds. The main applications of accelerator for decomposition of wastewaters are considered.

  2. A Socio-Technical Analysis of Patient Accessible Electronic Health Records.

    Science.gov (United States)

    Hägglund, Maria; Scandurra, Isabella

    2017-01-01

    In Sweden, and internationally, there is a movement towards increased transparency in healthcare including giving patients online access to their electronic health records (EHR). The purpose of this paper is to analyze the Swedish patient accessible EHR (PAEHR) service using a socio-technical framework, to increase the understanding of factors that influence the design, implementation, adoption and use of the service. Using the Sitting and Singh socio-technical framework as a basis for analyzing the Swedish PAEHR system and its context indicated that there are many stakeholders engaged in these types of services, with different driving forces and incentives that may influence the adoption and usefulness of PAEHR services. The analysis was useful in highlighting important areas that need to be further explored in evaluations of PAEHR services, and can act as a guide when planning evaluations of any PAEHR service.

  3. Technical aspects of portal technology application for e-health systems.

    Science.gov (United States)

    Kosińska, Joanna; Słowikowski, Paweł

    2004-01-01

    E-health is an emerging field on the intersection of medical information technologies, public health and business, referring to health services and information delivered or enhanced through the Internet and related technologies. Portal technology, allowing services to be accessible over the Internet is a perfect tool for providing e-health services. The use of portal technologies has had deep influence on the architecture of the whole e-health system, both regarding new subsystems and older ones which we want to integrate with the portal. Portals provide new possibilities for creating novel types of e-health applications as well. In this paper we provide a brief overview of e-health systems and portal technologies, and present many technical aspects of portal technology application for e-health systems such as the architecture of portal-based e-health systems, graphical user interfaces, access to various e-health systems' resources, personalization, security and privacy.

  4. Technical Training Seminar: Low-Voltage Differential Signaling (LVDS): Technology and Applications

    CERN Multimedia

    Monique Duval

    2004-01-01

    Tuesday 26 October TECHNICAL TRAINING SEMINAR from 14:00 to 16:30, Auditorium 40-SS-C01 Low-Voltage Differential Signaling (LVDS): Technology and Applications Herbert Eisenring, Kai Peters / NATIONAL SEMICONDUCTOR (Europe) National Semiconductor pioneered the Low-Voltage Differential Signaling (LVDS) technology, and is a recognized leader in high speed differential products and design tools. National Semiconductor offers a wide range of innovative, affordable interconnect solutions including serializer-deserializers (SerDes), drivers-receivers-transceivers, crosspoint switches and clock drivers. LVDS is a new technology addressing the needs of todays high performance data transmission applications, and the LVDS standard is becoming the most popular differential data transmission standard in the industry. This Technical Training Seminar will present National Semiconductor existing and future products, and some applications relevant to the activities carried out at CERN. 14:00 - 14:15 Presentation of Nati...

  5. Technical Training Seminar: Low-Voltage Differential Signaling (LVDS): Technology and Applications

    CERN Multimedia

    Monique Duval

    2004-01-01

    Tuesday 26 October TECHNICAL TRAINING SEMINAR from 14:00 to 16:30, Auditorium 40-SS-C01 Low-Voltage Differential Signaling (LVDS): Technology and Applications Herbert Eisenring, Kai Peters / NATIONAL SEMICONDUCTOR (Europe) National Semiconductor pioneered the Low-Voltage Differential Signaling (LVDS) technology, and is a recognized leader in high speed differential products and design tools. National Semiconductor offers a wide range of innovative, affordable interconnect solutions including serializer-deserializers (SerDes), drivers-receivers-transceivers, crosspoint switches and clock drivers. LVDS is a new technology addressing the needs of todays high performance data transmission applications, and the LVDS standard is becoming the most popular differential data transmission standard in the industry. This Technical Training Seminar will present National Semiconductor existing and future products, and some applications relevant to the activities carried out at CERN. 14:00 - 14:15 Presentation of Nat...

  6. A Review of Warm Mix Asphalt Technology: Technical, Eco-nomical and Enviromental Aspects

    Directory of Open Access Journals (Sweden)

    Hugo Alexander Rondón

    2015-09-01

    Full Text Available In general terms, warm mix asphalt (WMA technology presents a wide potential for successful use in road works construction projects. However, concerns remain regarding the durability and behavior of WMA mixtures in the long term, which need to be addressed. This review focuses on the technical, economic and environmental advantages and disadvantages. The review concludes that the main advantage, at the moment, of this technology concerns the environment. At the end of this work, the authors include certain recommendations for future works to continue strengthening the development of WMA technology.

  7. Innovative designs and technologies of nuclear power. IV International scientific and technical conference. Book of abstracts

    International Nuclear Information System (INIS)

    2016-01-01

    IV International scientific and technical conference “Innovative designs and technologies of nuclear power” has been organized and is conducted by JSC NIKIET with support from Rosatom State Corporation, the International Atomic Energy Agency, the Russian Academy of Sciences and the Nuclear Society of Russia. The conference topics include: innovative designs of nuclear facilities for various applications, nuclear fuel and new materials, closed fuel cycle technologies, SNF and RW management, technological answers to nonproliferation problems, small power reactors (stationary, transportable, floatable, propulsion, space), integrated codes of a new generation for safety analysis of nuclear power plants and fuel cycles, controlled fusion [ru

  8. Advances in electronic-nose technologies developed for biomedical applications

    Science.gov (United States)

    Dan Wilson; Manuela. Baietto

    2011-01-01

    The research and development of new electronic-nose applications in the biomedical field has accelerated at a phenomenal rate over the past 25 years. Many innovative e-nose technologies have provided solutions and applications to a wide variety of complex biomedical and healthcare problems. The purposes of this review are to present a comprehensive analysis of past and...

  9. Power Electronics as key technology in wind turbines

    DEFF Research Database (Denmark)

    Blaabjerg, Frede

    2005-01-01

    This paper discuss the development in wind turbines in a two-decade perspective looking at the technology based on track records. Different power electronic topologies for interfacing the wind turbine to the grid are discussed and related to the possibility for the wind turbine to act as a power...

  10. Application of electron beams to environmental conservation technology

    International Nuclear Information System (INIS)

    Pikaev, A.K.

    1992-01-01

    The paper is a review of current status of the application of electron beams to environmental conservation technology. Different aspects of radiation treatment of natural and polluted drinking water, radiation purification of industrial and municipal wastes, radiation treatment of sewage sludge and radiation purification of exhaust gases are considered. The special attention is paid to the respective pilot and industrial facilities. (author) 70 refs

  11. Special Article Ethics and Electronic Health Information Technology ...

    African Journals Online (AJOL)

    Objectives: The National Health Insurance Scheme (NHIS), and the National Identification Authority (NIA), pose ethical challenges to the physician-patient relationship due to interoperability. This paper explores (1) the national legislation on Electronic Health Information Technology (EHIT), (2) the ethics of information ...

  12. special article ethics and electronic health information technology

    African Journals Online (AJOL)

    David Ofori-Adjei

    Electronic Health Information Technology, (EHIT) has become an integral part of the national health care delivery system. Reliance on EHIT seems poised to grow in the years to come due to the myriad of advantages derived from the capture, storage, retrieval and analysis of large volumes of protected health data, and from ...

  13. Purification technology for flue/off gases using electron beams

    International Nuclear Information System (INIS)

    Kojima, Takuji

    2004-01-01

    The present paper describes research and development on purification technology using electron beams for flue/off gases containing pollutants: removal of sulfate oxide and nitrogen oxide from flue gases of coal/oil combustion power plants, decomposition of dioxins in waste incineration flue gas, and decomposition/removal of toxic volatile organic compounds from off gas. (author)

  14. HF electronic tubes. Technologies, grid tubes and klystrons

    International Nuclear Information System (INIS)

    Lemoine, Th.

    2009-01-01

    This article gives an overview of the basic technologies of electronic tubes: cathodes, electronic optics, vacuum and high voltage. Then the grid tubes, klystrons and inductive output tubes (IOT) are introduced. Content: 1 - context and classification; 2 - electronic tube technologies: cathodes, electronic optics, magnetic confinement (linear tubes), periodic permanent magnet (PPM) focussing, collectors, depressed collectors; 3 - vacuum technologies: vacuum quality, surface effects and interaction with electrostatic and RF fields, secondary emission, multipactor effect, thermo-electronic emission; 4 - grid tubes: operation of a triode, tetrodes, dynamic operation and classes of use, 'common grid' and 'common cathode' operation, ranges of utilisation and limitations, operation of a tetrode on unadjusted load, lifetime of a tetrode, uses of grid tubes; 5 - klystrons: operation, impact of space charge, multi-cavity klystrons, interaction efficiency, extended interaction klystrons, relation between interaction efficiency, perveance and efficiency, ranges of utilization and power limitations, multi-beam klystrons and sheet beam klystrons, operation on unadjusted load, klystron band pass and lifetime, uses; 6 - IOT: principle of operation, ranges of utilisation and limitations, interaction efficiency and depressed collector IOT, IOT lifetime and uses. (J.S.)

  15. Applications and Advances in Electronic-Nose Technologies

    Directory of Open Access Journals (Sweden)

    Manuela Baietto

    2009-06-01

    Full Text Available Electronic-nose devices have received considerable attention in the field of sensor technology during the past twenty years, largely due to the discovery of numerous applications derived from research in diverse fields of applied sciences. Recent applications of electronic nose technologies have come through advances in sensor design, material improvements, software innovations and progress in microcircuitry design and systems integration. The invention of many new e-nose sensor types and arrays, based on different detection principles and mechanisms, is closely correlated with the expansion of new applications. Electronic noses have provided a plethora of benefits to a variety of commercial industries, including the agricultural, biomedical, cosmetics, environmental, food, manufacturing, military, pharmaceutical, regulatory, and various scientific research fields. Advances have improved product attributes, uniformity, and consistency as a result of increases in quality control capabilities afforded by electronic-nose monitoring of all phases of industrial manufacturing processes. This paper is a review of the major electronic-nose technologies, developed since this specialized field was born and became prominent in the mid 1980s, and a summarization of some of the more important and useful applications that have been of greatest benefit to man.

  16. International Conference on NextGen Electronic Technologies

    CERN Document Server

    Thalmann, Nadia; Bhaaskaran, V

    2017-01-01

    This book is a collection of keynote lectures from international experts presented at International Conference on NextGen Electronic Technologies (ICNETS2-2016). ICNETS2 encompasses six symposia covering all aspects of electronics and communications domains, including relevant nano/micro materials and devices . This volume comprises of recent research in areas like computational signal processing analysis, intelligent embedded systems, nanoelectronic materials and devices, optical and microwave technologies, VLSI design: circuits systems and application, and wireless communication networks, and the internet of things. The contents of this book will be useful to researchers, professionals, and students working in the core areas of electronics and their applications, especially to signal processing, embedded systems, and networking.

  17. Applications of electron beam technology for healthcare and environment

    International Nuclear Information System (INIS)

    Varshney, Lalit

    2013-01-01

    Radiation technology has matured from lab scale to industrial scale in many areas of interests to industry, healthcare, agriculture and environment. Some of the well established applications include radiation sterilization, wires and cable, composites for automobiles, radiation surface curing, nanomaterials, hydrogels and special materials for nuclear and aerospace industry, radiation treatment of effluents, sewage sludge etc. These applications are as a result of characteristics of high energy radiation like gamma and electron beams which are able to deliver energy directly at molecular level. Unlike nuclear based radiations, electron beam accelerator technology is amenable to easy acceptance by public as well has capability to manipulate processes and product treatment to produce varieties of advanced/smart materials for healthcare and environment. Faster dose rates and depth profiling are the important characteristics of electron beam technology which gives it an edge over gamma radiation processing. Department of Atomic Energy has an ambitious program to indigenously develop accelerator technology and utilize them for national progress. In the presentation some important applications of radiation technology will be discussed. (author)

  18. Technical Training: ELEC-2005 - Electronics in High Energy Physics: Summer Term (May 2005)

    CERN Multimedia

    Davide Vitè

    2005-01-01

    ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme. It is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. The next ELEC-2005 Summer Term, System electronics for physics: Issues, is now open for online registration, and will start on May 10th. Lectures will take place on Tuesdays and Thursdays, from 10h00 to 12h30. The course will be in English, with questions and answers also possible in French. Separate registration to each Term is required: attendance costs will be of 10.- CHF per lecture (Summer Term: 70.- CHF). If you are interested in attending, please discuss with your supervisor and/or your DTO, and apply electronically via EDH. Participation to all sessions in a...

  19. Impact of Nuclear Technology to the National Socio-Economy: Technical Support by Nuclear Malaysia

    International Nuclear Information System (INIS)

    Hazmimi Kasim; Ainul Hayati Daud; Jamal Khaer Ibrahim; Alawiah Musa

    2011-01-01

    In Malaysia, the development of nuclear technology began in the year 1972. More than 30 years of application, today, the technology made impact to the national socio-economy through contribution to GDP and; improving quality of life and enhanced societal well-being. The application of nuclear technology both in public and private agencies in industrial, medical and agricultural sectors were considered. In 2008, the impact of nuclear technology shows the contribution of 0.032% to the total GDP. Industry sector shows an increasing trend and is the highest contributor, while agriculture sector remains the lowest. In this regard, Malaysian Nuclear Agency (Nuclear Malaysia) played an important role as a technical support agency in nuclear technology, as a supplier and provider for the service, training and research for the industrial, medical and agricultural sectors. (author)

  20. A systematic literature review on security and privacy of electronic health record systems: technical perspectives.

    Science.gov (United States)

    Rezaeibagha, Fatemeh; Win, Khin Than; Susilo, Willy

    Even though many safeguards and policies for electronic health record (EHR) security have been implemented, barriers to the privacy and security protection of EHR systems persist. This article presents the results of a systematic literature review regarding frequently adopted security and privacy technical features of EHR systems. Our inclusion criteria were full articles that dealt with the security and privacy of technical implementations of EHR systems published in English in peer-reviewed journals and conference proceedings between 1998 and 2013; 55 selected studies were reviewed in detail. We analysed the review results using two International Organization for Standardization (ISO) standards (29100 and 27002) in order to consolidate the study findings. Using this process, we identified 13 features that are essential to security and privacy in EHRs. These included system and application access control, compliance with security requirements, interoperability, integration and sharing, consent and choice mechanism, policies and regulation, applicability and scalability and cryptography techniques. This review highlights the importance of technical features, including mandated access control policies and consent mechanisms, to provide patients' consent, scalability through proper architecture and frameworks, and interoperability of health information systems, to EHR security and privacy requirements.

  1. Technical Training: EMAG-2005 - Electromagnetic Design and Mathematical Optimization Methods in Magnet Technology

    CERN Multimedia

    Monique Duval

    2005-01-01

    CERN Technical Training 2005: Learning for the LHC! CERN Technical Training, in collaboration with the AT-MEL-EM section, is organising a new course series in the framework of the 2005 CERN Technical Training programme: EMAG-2005 - Electromagnetic Design and Mathematical Optimization Methods in Magnet Technology, composed of three-hour lectures in the morning and topical seminars in the afternoon. The EMAG-2005 course series will run at CERN from Monday April 4 until Thursday April 14 (no lectures on Friday 8). The course series, in English, will focus on the foundations of electromagnetism and the design of accelerator magnets, both normal conducting and superconducting, employing analytical and numerical field computations. Examples of the LHC magnet design using the CERN field computation program ROXIE will be presented. However, EMAG-2005 is not a ROXIE user course: it is rather a course for users or potential users of numerical field computation software, and for magnet designers. The course will be o...

  2. Social Relations of Science and Technology: perceptions of teachers of technical training, PARFOR course participants

    Directory of Open Access Journals (Sweden)

    Manuella Candéo

    2014-12-01

    Full Text Available We present in this paper a study on the perceptions of teachers of technical training, course participants (PARFOR National Plan for Training Teachers of Basic Education , offered by the Federal Technological University of Paraná, Campus Ponta Grossa (PG - UTFPR on the social relations of science and technology. The study conducted with 15 teachers from various disciplines. The methodological approach was quantitative research , the instrument of data collection was based questionnaire with open questions . The main results show that the vast majority of teachers had a very narrow view about science and technology , consider that the scientific and technological development always bring benefits to its own population of traditional / classic , positivist view. The need to promote reflection on social issues of science and technology in education technology in order to train professionals aware of their responsibilities as citizens in a highly technological age was observed. It is emphasized that these are recorded in the master's thesis entitled Scientific and Technological Literacy (ACT by Focus Science, Technology and Society (STS from commercial films of the University Program Graduate School of Science and Technology Tecnológica Federal do Paraná ( UTFPR Campus Ponta Grossa, Brazil.

  3. Survey on the Technology Readiness Level of R and D projects for a Technical Risk Management

    International Nuclear Information System (INIS)

    Song, S. J.; Chang, J.; Lee, K. Y.

    2008-01-01

    The purpose of applying the Technology Readiness Level/Design Readiness Level (TRL/DRL) in technical risk management is to make technology assessments, and improve communication among researchers with a consistent, systematic technology readiness Technical risk management for the Nuclear Hydrogen Production project was adopted of experience assessed with Delphi Method from the Next Generation Nuclear Plant(NGNP)of the DOE to improve the poor contactor management of the major projects which experienced cost increases and/or schedule delays in long-term. In the current phase that is doing key technology research and development projects, the technology readiness level was reviewed and applied to the Nuclear Hydrogen Production project to prepare an input for the next design phases. Based on the previous works, pre-conceptional design and key R and D works for the Nuclear Hydrogen Design and Development(NHDD) projects and the results of key research and development projects, the TRL was applied to assess the levels and compared with the advanced design stages of Westinghouse Electric Co. With this process, several issues were identified to apply the design and technology level to the familiar steps of design process and research and development projects. In order to resolve these issues, it is needed to systematically adjust and modify the current process with TRLs

  4. Technical and Technological Support of Agricultural Enterprises on the Basis of Association Interaction: a Methodical Approach

    Directory of Open Access Journals (Sweden)

    Pyvovar Petro V.

    2017-12-01

    Full Text Available The aim of the research is the development of a methodical approach to justifying directions of association interaction of agricultural enterprises for the most effective technical and technological support of their economic activities. It is substantiated that the decision-making regarding the directions of group interaction in the field of forming and using the machine and tractor fleet of agricultural enterprises should be based on results of a strategic analysis of the current level of and trends in the changes in indicators of their technical support. This includes several stages: 1 determining a scenario for the development of the technical base of the economic entity (matrix methods; 2 multifactor grouping taking into account the available equipment and resource potential; 3 identification of potential sources of financing and ways of attracting necessary funds, priority partners and types of equipment and technologies; 4 estimation of a current condition of the enterprise on financial, technical, economic and market criteria; 5 substantiation of directions of group interaction of the enterprise.

  5. 25 CFR 547.15 - What are the minimum technical standards for electronic data communications between system...

    Science.gov (United States)

    2010-04-01

    ... communications between system components? This section provides minimum standards for electronic data... 25 Indians 2 2010-04-01 2010-04-01 false What are the minimum technical standards for electronic data communications between system components? 547.15 Section 547.15 Indians NATIONAL INDIAN GAMING...

  6. Developing electron beam bunching technology for improving light sources

    International Nuclear Information System (INIS)

    Carlsten, B.E.; Chan, K.C.D.; Feldman, D.W.

    1997-01-01

    This is the final report of a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The goal of this project was to develop a new electron bunch compression technology, experimentally demonstrate subpicosecond compression of bunches with charges on the order of 1 nC, and to theoretically investigate fundamental limitations to electron bunch compression. All of these goals were achieved, and in addition, the compression system built for this project was used to generate 22 nm light in a plasma-radiator light source

  7. Technical Support Document: 50% Energy Savings Design Technology Packages for Highway Lodging Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Wei; Gowri, Krishnan; Lane, Michael D.; Thornton, Brian A.; Rosenberg, Michael I.; Liu, Bing

    2009-09-28

    This Technical Support Document (TSD) describes the process, methodology and assumptions for development of the 50% Energy Savings Design Technology Packages for Highway Lodging Buildings, a design guidance document intended to provide recommendations for achieving 50% energy savings in highway lodging properties over the energy-efficiency levels contained in ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings.

  8. TANK FARM REMEDIATION TECHNOLOGY DEVELOPMENT PROJECT AN EXERCISE IN TECHNICAL & REGULATORY COLLABORATION

    Energy Technology Data Exchange (ETDEWEB)

    JARAYSI, M.N.

    2007-01-08

    The Tank Farm Remediation Technology Development Project at the Hanford Site focuses on waste storage tanks, pipelines and associated ancillary equipment that are part of the C-200 single-shell tank (SST) farm system located in the C Tank Farm. The purpose of the project is to obtain information on the implementation of a variety of closure activities and to answer questions on technical, operational and regulatory issues associated with closure.

  9. Solar Energy Technologies Program: Multi-Year Technical Plan 2003-2007 and Beyond

    Energy Technology Data Exchange (ETDEWEB)

    2004-01-01

    This publication charts a 5-year planning cycle for the U.S. Department of Energy Solar Energy Technologies Program. The document includes anticipated technical plans for the next 5 years for photovoltaics, concentrating solar power, solar water and space heating, solar hybrid lighting, and other new concepts that can take advantage of the solar resource. Solar energy is described as a clean, abundant, renewable energy resource that can benefit the nation by diversifying our energy supply.

  10. TANK FARM REMEDIATION TECHNOLOGY DEVELOPMENT PROJECT AN EXERCISE IN TECHNICAL and REGULATORY COLLABORATION

    International Nuclear Information System (INIS)

    JARAYSI, M.N.

    2007-01-01

    The Tank Farm Remediation Technology Development Project at the Hanford Site focuses on waste storage tanks, pipelines and associated ancillary equipment that are part of the C-200 single-shell tank (SST) farm system located in the C Tank Farm. The purpose of the project is to obtain information on the implementation of a variety of closure activities and to answer questions on technical, operational and regulatory issues associated with closure

  11. Technical investigation in solid waste to energy facilities and selection of suitable incineration technology for Tehran

    International Nuclear Information System (INIS)

    Mokarizdeh, V.; Lari, H.R.

    2001-01-01

    Incineration is another way for producing electrical energy. There are various methods for incineration as Stoker Fired, Suspension Fired, Rotary Kiln, Cyclone and Fluidized Bed; that each one has it's own advantages and disadvantages. Selecting suitable one for establishment in Tehran depends on many parameters like technical, economical and environmental factors. Comparing the various technologies due to the mentioned parameters by Multi Criteria Decision Making method shows that stoker-fired incinerator is the best one for the Capital City

  12. Development of applications for Indian industry using electron beam technology

    International Nuclear Information System (INIS)

    Sarma, K.S.S.; Khader, S.A.; Sabharwal, S.

    2009-01-01

    This paper presents a report on the industrial applications that have been developed and demonstrated to the Indian industry using 2MeV/20kW Electron Beam accelerator at BARC-BRIT in the field of polymer modifications (crosslinking and degradation), gem stone coloration etc. Technological scale demonstration of the applications citing the benefits in terms of clean technology and better economics, encouraged three companies in private industry to set up EB facilities for the treatment of cable insulations, heat shrinkable products, diamond and gem stones during the last five years. Recent work on EB processing of automobile rubber tires is also included. (author)

  13. FEATURES OF TECHNOLOGIES CREATE INTERACTIVE ELECTRONIC DOCUMENT FOR SUPPORT OF LABORATORY PRACTICAL PHYSICS

    Directory of Open Access Journals (Sweden)

    Mykola A. Meleshko

    2014-02-01

    Full Text Available The article discusses the content of the «flash-book» construct, defining its properties and possible components. There are presented some examples of components programming steps of “authoring flash – book”, considered the possibility of using such an electronic document to optimize the learning process at the Technical University in the performance of laboratory training on general physics. The technique of its using to provide individualized approach to learning and the use of various experimental base from classical to digital equipment laboratories is proposed. It was carried out the analysis of ways to improve such interactive electronic document for the development of information technology competence of engineering students.

  14. Proceedings of symposium on technology in laboratories by department of engineering and technical services

    International Nuclear Information System (INIS)

    1994-07-01

    The Symposium on Technology in Laboratories was held on March 23 and 24 at Ceratopia Toki, and Toki Chamber of Commerce and Industry in Toki city, Gifu Prefecture, Japan. This symposium was hosted by National Institute for Fusion Science (NIFS). There were 273 participants from many Japanese universities and laboratories, from some Japanese industrial world. Seventy eight papers were presented in the symposium. Technical experience and new techniques were reported and discussed being divided into five sessions; technologies of fabrication, cryogenics, diagnostic and control system, computer and experimental apparatus. (author)

  15. Prospects for using the technology of circulating fluidized bed for technically refitting Russian thermal power stations

    Science.gov (United States)

    Ryabov, G. A.; Folomeev, O. M.; Litun, D. S.; Sankin, D. A.; Dmitryukova, I. G.

    2009-01-01

    The present state and development of circulating fluidized bed (CFB) technology around the world are briefly reviewed. Questions of increasing the capacity of single boiler units and raising the parameters of steam are discussed. CFB boilers for 225- and 330-MW power units are described and their parameters are estimated as applied to the conditions of firing different Russian fuels. Indicators characterizing CFB boilers and pulverized-coal boilers are given. Capital outlays and operational costs for new coal-fired units are compared, and the results from this comparison are used to show the field of the most promising use of the CFB technology during technical refitting of Russian thermal power stations.

  16. Technical and Economic Assessment of Storage Technologies for Power-Supply Grids

    Directory of Open Access Journals (Sweden)

    H. Meiwes

    2009-01-01

    Full Text Available Fluctuating power generation from renewable energies such as wind and photovoltaic are a technical challenge for grid stability. Storage systems are an option to stabilise the grid and to maximise the utilisation factors of renewable power generators. This paper analyses the state of the art of storage technologies, including a detailed life cycle cost comparison. Beside this, benefits of using storage systems in electric vehicles are analysed and quantified. A comprehensive overview of storage technologies as well as possible applications and business cases for storage systems is presented. 

  17. Power electronics - The key technology for Renewable Energy Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Ma, Ke; Yang, Yongheng

    2014-01-01

    The energy paradigms in many countries (e.g. Germany and Denmark) have experienced a significant change from fossil-based resources to clean renewables (e.g. wind turbines and photovoltaics) in the past few decades. The scenario of highly penetrated renewables is going to be further enhanced...... - Denmark expects to be 100 % fossil-free by 2050. Consequently, it is required that the production, distribution and use of the energy should be as technologically efficient as possible and incentives to save energy at the end-user should also be strengthened. In order to realize the transition smoothly...... and effectively, energy conversion systems, currently based on power electronics technology, will again play an essential role in this energy paradigm shift. Using highly efficient power electronics in power generation, power transmission/distribution and end-user application, together with advanced control...

  18. Intellectual property in consumer electronics, software and technology startups

    CERN Document Server

    Halt, Jr , Gerald B; Stiles, Amber R; Fesnak, Robert

    2014-01-01

    This book provides a comprehensive guide to procuring, utilizing and monetizing intellectual property rights, tailored for readers in the high-tech consumer electronics and software industries, as well as technology startups.  Numerous, real examples, case studies and scenarios are incorporated throughout the book to illustrate the topics discussed.  Readers will learn what to consider throughout the various creative phases of a product’s lifespan from initial research and development initiatives through post-production.  Readers will gain an understanding of the intellectual property protections afforded to U.S. corporations, methods to pro-actively reduce potential problems, and guidelines for future considerations to reduce legal spending, prevent IP theft, and allow for greater profitability from corporate innovation and inventiveness. • Offers a comprehensive guide to intellectual property for readers in high-tech consumer electronics, software and technology startups; • Uses real case studies...

  19. Celebrating 25 years of technical cooperation for promotion of nuclear science, technology in Latin America, Caribbean

    International Nuclear Information System (INIS)

    2009-01-01

    Full text: The IAEA celebrates the 25th Anniversary of the Regional Agreement of Technical Cooperation for the Promotion of Nuclear Science and Technology in Latin America and the Caribbean (ARCAL) for the peaceful use of nuclear energy as well as its applications for development during the 53rd General Conference of the International Atomic Energy Agency, taking place this week. The Board of Country Representatives of ARCAL (BAR) is celebrating the 25th anniversary of the Regional Agreement of Technical Cooperation for the Promotion of Nuclear Science and Technology in Latin America and the Caribbean (ARCAL) from 14-18 September, during the 53rd General Conference of the IAEA in Vienna, Austria. Through sustainable horizontal technical and economic cooperation over the past 25 years, the IAEA Member States of Latin America and the Caribbean have expressed their solidarity and commitment to the establishment and improvement of technical capabilities in nuclear science and technology within the region, with the goal of promoting the use of diverse nuclear techniques and their applications for peaceful use in the region. Thanks to the ARCAL agreement, a mechanism for regular meetings and discussions has been established between professionals working in the nuclear field in Latin America and the Caribbean. ARCAL was established in 1984, thanks to the initiative of the Andean Group countries. At the moment, ARCAL has 19 Member States: Argentina, Bolivia, Brazil, Chile, Colombia, Costa Rica, Cuba, Ecuador, El Salvador, Guatemala, Haiti, Mexico, Nicaragua, Panama, Paraguay, Peru, Dominican Republic, Uruguay and Venezuela. The main thematic areas covered by the technical cooperation projects sponsored by the IAEA through the ARCAL agreement are human health, agriculture and food security, physics and chemistry sciences, engineering and technology, hydrology, industrial applications, environment and nuclear security. During its 25 years, the ARCAL regional agreement has

  20. Celebrating 25 years of technical cooperation for promotion of nuclear science, technology in Latin America, Caribbean

    International Nuclear Information System (INIS)

    2009-01-01

    Full text: The IAEA celebrates the 25th Anniversary of the Regional Agreement of Technical Cooperation for the Promotion of Nuclear Science and Technology in Latin America and the Caribbean (ARCAL) for the peaceful use of nuclear energy as well as its applications for development during the 53rd General Conference of the International Atomic Energy Agency, taking place this week. The Board of Country Representatives of ARCAL (BAR) is celebrating the 25th anniversary of the Regional Agreement of Technical Cooperation for the Promotion of Nuclear Science and Technology in Latin America and the Caribbean (ARCAL) from 14-18 September, during the 53rd General Conference of the IAEA in Vienna, Austria. Through sustainable horizontal technical and economic cooperation over the past 25 years, the IAEA Member States of Latin America and the Caribbean have expressed their solidarity and commitment to the establishment and improvement of technical capabilities in nuclear science and technology within the region, with the goal of promoting the use of diverse nuclear techniques and their applications for peaceful use in the region. Thanks to the ARCAL agreement, a mechanism for regular meetings and discussions has been established between professionals working in the nuclear field in Latin America and the Caribbean. ARCAL was established in 1984, thanks to the initiative of the Andean Group countries. At the moment, ARCAL has 19 Member States: Argentina, Bolivia, Brazil, Chile, Colombia, Costa Rica, Cuba, Ecuador, El Salvador, Guatemala, Haiti, Mexico, Nicaragua, Panama, Paraguay, Peru, Dominican Republic, Uruguay and Venezuela. The main thematic areas covered by the technical cooperation projects sponsored by the IAEA through the ARCAL agreement are human health, agriculture and food security, physics and chemistry sciences, engineering and technology, hydrology, industrial applications, environment and nuclear security. During its 25 years, the ARCAL regional agreement has

  1. Mathematical Model of Plasma Space for Electronic Technologies

    OpenAIRE

    N.N. Chernyshov; K.T. Umyarov; D.V. Pisarenko

    2014-01-01

    The paper is devoted to studying the plasma used in technologies of the electronic industry. It gives the characteristic of plasma space on the basis of a system of Maxwell-Boltzmann equa-tions. Solving these equations is represented in the form of Fourier transformation and Green functions. Fluctuation-dissipative theorem and method of Longevin sources for calculating electric filed fluctua-tions are used.

  2. Electronic-projecting Moire method applying CBR-technology

    Science.gov (United States)

    Kuzyakov, O. N.; Lapteva, U. V.; Andreeva, M. A.

    2018-01-01

    Electronic-projecting method based on Moire effect for examining surface topology is suggested. Conditions of forming Moire fringes and their parameters’ dependence on reference parameters of object and virtual grids are analyzed. Control system structure and decision-making subsystem are elaborated. Subsystem execution includes CBR-technology, based on applying case base. The approach related to analysing and forming decision for each separate local area with consequent formation of common topology map is applied.

  3. Leveraging Technological Capabilities across Polarized Cultures: Shanghai Delco Electronics Limited

    OpenAIRE

    Lucy A. Ojode

    2006-01-01

    Rallying its units for an impending spin-off from General Motors, the Delphi Automotive Systems division cleared the Delphi Delco Electronics (Delphi-D) unit to begin planning for entry into China in 1994. Delphi saw China as ideal for leveraging its technological and innovation capabilities as well as the enormous General Motor heritage and reputation from years of experience delivering quality products to the automotive industry. Delphi-D found a perfect partner in Shanghai Changjiang YiBia...

  4. Development of electron beam flue gas treatment technology

    International Nuclear Information System (INIS)

    Tanaka, T.

    1995-01-01

    The electron beam flue gas treatment technology is expected to bring many advantages such as the simultaneous reduction of SO x and NO x emissions, a dry process without waste water, valuable fertilizer byproducts, etc. In order to verify the feasibility and performances of the process, a practical application test is carried out with a pilot plant which treats the actual flue gas from a coal-fired boiler. Results are presented. 4 figs., 2 tabs

  5. Technical and economic evaluation of selected technologies of the Landfill Characterization System

    Energy Technology Data Exchange (ETDEWEB)

    Floran, R.J.

    1993-12-31

    In 1992 and 1993, numerous innovative and emerging technologies for characterizing metal and mixed waste contaminants and their migration beneath landfills in and environments were field tested at Sandia`s Chemical Waste Landfill. Many of these technologies are being evaluated as part of the Landfill Characterization System (LCS). The LCS emphasizes minimally intrusive technologies and downhole sensors that strive to be cheaper, better, safer and faster than conventional methods. Major aims of the LCS are to demonstrate, test and evaluate these technologies, and determine whether substantial cost saving over traditional baseline methods can be realized. To achieve these goals, the LCS uses an integrated systems approach that stresses the application of complementary and compatible technologies. Successful field demonstrations combined with favorable economics, will greatly assist the commercialization of these technologies to the private sector and to Environmental Restoration groups throughout the DOE Complex. In this paper, a technical and economic evaluation of selected technologies that comprise the LCS is presented. Because sampling and analysis is the most costly part of a characterization effort, the economic evaluation presented here focuses specifically on these activities. LCS technologies discussed include the ``Smart Sampling Methodology`` and two field screening analytical methods, stripping voltammetry and x-ray fluorescence.

  6. Meat Quality Assessment by Electronic Nose (Machine Olfaction Technology

    Directory of Open Access Journals (Sweden)

    Sundar Balasubramanian

    2009-07-01

    Full Text Available Over the last twenty years, newly developed chemical sensor systems (so called “electronic noses” have made odor analyses possible. These systems involve various types of electronic chemical gas sensors with partial specificity, as well as suitable statistical methods enabling the recognition of complex odors. As commercial instruments have become available, a substantial increase in research into the application of electronic noses in the evaluation of volatile compounds in food, cosmetic and other items of everyday life is observed. At present, the commercial gas sensor technologies comprise metal oxide semiconductors, metal oxide semiconductor field effect transistors, organic conducting polymers, and piezoelectric crystal sensors. Further sensors based on fibreoptic, electrochemical and bi-metal principles are still in the developmental stage. Statistical analysis techniques range from simple graphical evaluation to multivariate analysis such as artificial neural network and radial basis function. The introduction of electronic noses into the area of food is envisaged for quality control, process monitoring, freshness evaluation, shelf-life investigation and authenticity assessment. Considerable work has already been carried out on meat, grains, coffee, mushrooms, cheese, sugar, fish, beer and other beverages, as well as on the odor quality evaluation of food packaging material. This paper describes the applications of these systems for meat quality assessment, where fast detection methods are essential for appropriate product management. The results suggest the possibility of using this new technology in meat handling.

  7. Meat quality assessment by electronic nose (machine olfaction technology).

    Science.gov (United States)

    Ghasemi-Varnamkhasti, Mahdi; Mohtasebi, Seyed Saeid; Siadat, Maryam; Balasubramanian, Sundar

    2009-01-01

    Over the last twenty years, newly developed chemical sensor systems (so called "electronic noses") have made odor analyses possible. These systems involve various types of electronic chemical gas sensors with partial specificity, as well as suitable statistical methods enabling the recognition of complex odors. As commercial instruments have become available, a substantial increase in research into the application of electronic noses in the evaluation of volatile compounds in food, cosmetic and other items of everyday life is observed. At present, the commercial gas sensor technologies comprise metal oxide semiconductors, metal oxide semiconductor field effect transistors, organic conducting polymers, and piezoelectric crystal sensors. Further sensors based on fibreoptic, electrochemical and bi-metal principles are still in the developmental stage. Statistical analysis techniques range from simple graphical evaluation to multivariate analysis such as artificial neural network and radial basis function. The introduction of electronic noses into the area of food is envisaged for quality control, process monitoring, freshness evaluation, shelf-life investigation and authenticity assessment. Considerable work has already been carried out on meat, grains, coffee, mushrooms, cheese, sugar, fish, beer and other beverages, as well as on the odor quality evaluation of food packaging material. This paper describes the applications of these systems for meat quality assessment, where fast detection methods are essential for appropriate product management. The results suggest the possibility of using this new technology in meat handling.

  8. Status of electron beam processing technology in Malaysia

    International Nuclear Information System (INIS)

    Ghazali, Zulkafli; Dahlan, Khairul Zaman; Aiasah, S.H.; Khomsaton, A.B.; Ting, T.M.

    2003-01-01

    The electron beam processing in Malaysia starting in 1991 at MINT (Malaysian Institute for Nuclear Technology Research) has been focussed on medical product sterilization, curing of surface coating and polymer modifications. Subsequent installation of accelerators by private companies promoted the development of radiation processing technologies for the use of production of heat-shrinkable products, pilot-scale flue gas purification, as well as wires, cables, tubes and hydrogels. Decomposition of a wide range of volatile organic compounds from industrial exhausts (car painting lines, volatile dioxin and furan from municipal waste incinerators) and purification of liquid wastewater and drinking water are also being under R and D work. Malaysia will continue to play an active part in the program on radiation technology to strengthen environmentally sustainable development in line with FNCA objectives. (S. Ohno)

  9. Application of electron beam curing technology for paper products

    International Nuclear Information System (INIS)

    Takaharu Miura

    1999-01-01

    The electron beam (EB) curing technology has rapidly advanced in recent years. However there were few examples applying this technology to paper products. One reason comes from the high price of EB equipment and the other comes from the difficulty of controlling the irradiation which gives damages to paper. In spite of these problems, the EB cured coating layer shows remarkable features, such as solvent-resistance, water-resistance, heat-resistance and high smoothness using the drum casting technique. Concentrating on application of this technology to paper, we have already developed some products. For example, paper for printings (Super Mirror PN) and for white boards (Super Mirror WB) have been manufactured. In this presentation, we are going to introduce this EB curing technique and the products

  10. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 33: Technical communications practices and the use of information technologies as reported by Dutch and US aerospace engineers

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Tan, Axel S. T.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. A self-administered questionnaire was distributed to aerospace engineers and scientists at the National Aerospace Laboratory (The Netherlands), and NASA ARC (U.S.), and NASA LaRC (U.S.). This paper presents responses of the Dutch and U.S. participants to selected questions concerning four of the seven project objectives: determining the importance of technical communications to aerospace engineering professionals, investigating the production of technical communications, examining the use and importance of computer and information technology, and exploring the use of electronic networks.

  11. Development of superconducting acceleration cavity technology for free electron lasers

    International Nuclear Information System (INIS)

    Lee, Jong Min; Lee, Byung Cheol; Kim, Sun Kook; Jeong, Young Uk; Cho, Sung Oh

    2000-10-01

    As a result of the cooperative research between the KAERI and Peking University, the key technologies of superconducting acceleration cavity and photoelectron gun have been developed for the application to high power free electron lasers. A 1.5-GHz, 1-cell superconducting RF cavity has been designed and fabricated by using pure Nb sheets. The unloaded Q values of the fabricated superconducting cavity has been measured to be 2x10 9 at 2.5K, and 8x10 9 at 1.8K. The maximum acceleration gradient achieved was 12 MeV/m at 2.5K, and 20MV/m at 1.8 K. A cryostat for the 1-cell superconducting cavity has been designed. As a source of electron beam, a DC photocathode electron gun has been designed and fabricated, which is composed of a photocathode evaporation chamber and a 100-keV acceleration chamber. The efficiency of the Cs2Te photocathode is 3% nominally at room temperature, 10% at 290 deg C. The superconducting photoelectron gun system developed has been estimated to be a good source of high-brightness electron beam for high-power free electron lasers

  12. Innovative technologies in course Electrical engineering and electronics

    Science.gov (United States)

    Kuznetsov, E. V.; Kiselev, V. I.; Kulikova, E. A.

    2017-11-01

    Department of Electrical Engineering and Nondestructive Testing, NRU “MPEI”, has been working on development Electronic Learning Resources (ELRs) in course Electrical Engineering and Electronics for several years. This work have been focused on education intensification and effectiveness while training bachelors in nonelectrical specializations including students from Thermal and Atomic Power Engineering Institute. The developed ELRs are united in a tutorial module consisting of three parts (Electrical Circuits, Electrical Machines, Basics of Electronics): electronic textbook and workbook (ETW); virtual laboratory sessions (VLS); training sessions (ETS); personal tasks (PT); testing system that contains electronic tests in all course subjects and built-in verification of a student’s work results in ETW, VLS, ETS, PT. The report presents samples of different ELRs in html format and MathCAD, MatLAB Simulink applications, copyrighted programs in Java2, Delphi, VB6, C++. The report also contains the experience description, advantages and disadvantages of the new technologies. It is mentioned that ELRs provide new opportunities in course studying.

  13. Development of superconducting acceleration cavity technology for free electron lasers

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jong Min; Lee, Byung Cheol; Kim, Sun Kook; Jeong, Young Uk; Cho, Sung Oh

    2000-10-01

    As a result of the cooperative research between the KAERI and Peking University, the key technologies of superconducting acceleration cavity and photoelectron gun have been developed for the application to high power free electron lasers. A 1.5-GHz, 1-cell superconducting RF cavity has been designed and fabricated by using pure Nb sheets. The unloaded Q values of the fabricated superconducting cavity has been measured to be 2x10{sup 9} at 2.5K, and 8x10{sup 9} at 1.8K. The maximum acceleration gradient achieved was 12 MeV/m at 2.5K, and 20MV/m at 1.8 K. A cryostat for the 1-cell superconducting cavity has been designed. As a source of electron beam, a DC photocathode electron gun has been designed and fabricated, which is composed of a photocathode evaporation chamber and a 100-keV acceleration chamber. The efficiency of the Cs2Te photocathode is 3% nominally at room temperature, 10% at 290 deg C. The superconducting photoelectron gun system developed has been estimated to be a good source of high-brightness electron beam for high-power free electron lasers.

  14. Electron beam processing technology for modification of different types of cellulose pulps for production of derivatives

    International Nuclear Information System (INIS)

    Iller, E.; Kukielka, A.; Mikolajczyk, W.; Starostka, P.; Stupinska, H.

    2002-01-01

    Institute of Nuclear Chemistry and Technology, Pulp and Paper Research Institute and Institute of Chemical Fibers carry out a joint research project in order to develop the radiation methods modification of cellulose pulps for production of cellulose derivatives such as carbamate (CC), carboxymethyl cellulose (CMC) and methylcellulose (MC). Three different types of textile pulps: Alicell (A); Borregaard (B), Ketchikan (K) and Kraft softwood (PSS) and hardwood (PSB) pulps have been irradiated with 10 MeV electron beam from LAE 13/9 linear accelerator with doses of 5, 10, 15, 20, 25 and 50 kGy. After electron beam treatment the samples of cellulose pulps have been examined by using of structural and physico-chemical methods. Electron paramagnetic resonance spectroscopy (EPR), gel permeation chromatography (GPC) and infrared spectroscopy (IRS) were applied for determination of structural changes in irradiated cellulose pulps. By means of analytical methods, such parameters as: viscosity, average degree of polymerization (DP) and α-cellulose contents were evaluated. Based on EPR and GPC investigations the relationship between concentrations of free radicals and decreasing polymerization degrees in electron beam treatment pulps has been confirmed. The carboxymethylcellulose, methylcellulose and cellulose carbamate were prepared using the raw material of radiation modified pulps. Positive results of investigations will allow for determination of optimum conditions for electron beam modification of selected cellulose paper and textile pulps. Such procedure leads to limit the amounts of chemical activators used in methods for preparation cellulose derivatives. The proposed electron beam technology is new approaches in technical solution and economic of process of cellulose derivatives preparation. (author)

  15. Double-Loop Health Technology: Enabling Socio-technical Design of Personal Health Technology in Clinical Practice

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Frost, Mads

    2018-01-01

    present a case of designing personal health technology for mental health, which is integrated into hospital-based treatment. This system helps patients to manage their disease by tracking and correlation behavior and disease progression and provide feedback to them, while also deployed as part......Personal health technology is rapidly emerging as a response to the challenges associated with significant increase in chronic noncommunicable diseases. The overall design paradigm behind most of these applications is to manually and automatically sample data from sensors and smartphones and use...... this to provide patients with an awareness of their illness and give recommendation for treatment, care, and healthy living. Few of these systems are, however, designed to be part of a complex socio-technical care and treatment processes in existing healthcare systems and clinical pathways. In this chapter, we...

  16. Long-term high-level waste technology. Composite quarterly technical report, July-September 1980

    International Nuclear Information System (INIS)

    Cornman, W.R.

    1981-02-01

    This composite quarterly technical report summarizes work performed at participating sites to immobilize high-level radioactive wastes. The technical information included in this report is structured along the lines of the Work Breakdown Structure adopted for use in the High-Level Waste Management Technology (WBS) program. The functions and work elements of the WBS are as follows: function 1 - program management and support, which includes work elements of management and budget, environmental and safety assessments, and other support; function 2 - waste preparation, which includes in-situ storage or disposal, waste retrieval, and separation and concentration; function 3 - waste fixation with work elements of waste form development and characterization, and process and equipment development; and function 4 - final handling which includes canister development and characterization, and onsite storage or disposal

  17. Healthcare technology innovation adoption electronic health records and other emerging health information technology innovations

    CERN Document Server

    Daim, Tugrul U; Basoglu, Nuri; Kök, Orhun M; Hogaboam, Liliya

    2016-01-01

    This book aims to study the factors affecting the adoption and diffusion of Health Information Technology (HIT) innovation. It analyzes the adoption processes of various tools and applications, particularly Electronic Health Records (EHR), highlighting the impact on various sectors of the healthcare system, such as physicians, administration,  and patient care, while also identifying the various pitfalls and gaps in the literature. With the various challenges currently facing the United States healthcare system, the study, adoption and diffusion of healthcare technology innovation, particularly HIT, is imperative to achieving national goals. This book is organized into three sections. Section one reviews theories and applications for the diffusion of Health Care Technologies. Section two evaluates EHR technology, including the barriers and enables in adoption and alternative technologies. Finally, section three examines the factors impacting the adoption of EHR systems. This book will be a key source for stu...

  18. Let's get technical: Enhancing program evaluation through the use and integration of internet and mobile technologies.

    Science.gov (United States)

    Materia, Frank T; Miller, Elizabeth A; Runion, Megan C; Chesnut, Ryan P; Irvin, Jamie B; Richardson, Cameron B; Perkins, Daniel F

    2016-06-01

    Program evaluation has become increasingly important, and information on program performance often drives funding decisions. Technology use and integration can help ease the burdens associated with program evaluation by reducing the resources needed (e.g., time, money, staff) and increasing evaluation efficiency. This paper reviews how program evaluators, across disciplines, can apply internet and mobile technologies to key aspects of program evaluation, which consist of participant registration, participant tracking and retention, process evaluation (e.g., fidelity, assignment completion), and outcome evaluation (e.g., behavior change, knowledge gain). In addition, the paper focuses on the ease of use, relative cost, and fit with populations. An examination on how these tools can be integrated to enhance data collection and program evaluation is discussed. Important limitations of and considerations for technology integration, including the level of technical skill, cost needed to integrate various technologies, data management strategies, and ethical considerations, are highlighted. Lastly, a case study of technology use in an evaluation conducted by the Clearinghouse for Military Family Readiness at Penn State is presented and illustrates how technology integration can enhance program evaluation. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Repetitive nanosecond electron accelerators type URT-1 for radiation technology

    Science.gov (United States)

    Sokovnin, S. Yu.; Balezin, M. E.

    2018-03-01

    The electron accelerator URT-1М-300 for mobile installation was created for radiation disinfecting to correct drawbacks that were found the URT-1M electron accelerator operation (the accelerating voltage up to 1 МV, repetition rate up to 300 pps, electron beam size 400 × 100 mm, the pulse width about 100 ns). Accelerator configuration was changed that allowed to reduce significantly by 20% tank volume with oil where is placed the system of formation high-voltage pulses, thus the average power of the accelerator is increased by 6 times at the expense of increase in pulses repetition rate. Was created the system of the computerized monitoring parameters (output parameters and thermal mode) and remote control of the accelerator (charge voltage, pulse repetition rate), its elements and auxiliary systems (heat of the thyratron, vacuum system), the remote control panel is connected to the installation by the fiber-optical channel, what lightens the work for service personnel. For generating an electron beam up to 400 mm wide there are used metal- ceramic] and metal-dielectric cold cathodes of several emission elements (plates) with a non-uniform distribution of the electron beam current density on the output foil ± 15%. It was found that emission drop of both type of cathodes, during the operation at the high repetition rate (100 pps) is substantial at the beginning of the process, and then proceeds rather slowly that allows for continuous operation up to 40 h. Experiments showed that linear dependence of the voltage and a signal from the pin-diode remains within the range of the charge voltage 45-65 kV. Thus, voltage increases from 690 to 950 kV, and the signal from the pin-diode - from (2,8-4,6)*104 Gy/s. It allows to select electron energy quite precisely with consideration of the radiation technology requirements.

  20. Monolithic millimeter-wave and picosecond electronic technologies

    International Nuclear Information System (INIS)

    Talley, W.K.; Luhmann, N.C.

    1996-01-01

    Theoretical and experimental studies into monolithic millimeter-wave and picosecond electronic technologies have been undertaken as a collaborative project between the Lawrence Livermore National Laboratory (LLNL) and the University of California Department of Applied Science Coherent Millimeter-Wave Group under the auspices of the Laboratory Directed Research and Development Program at LLNL. The work involves the design and fabrication of monolithic frequency multiplier, beam control, and imaging arrays for millimeter-wave imaging and radar, as well as the development of high speed nonlinear transmission lines for ultra-wideband radar imaging, time domain materials characterization and magnetic fusion plasma applications. In addition, the Coherent Millimeter-Wave Group is involved in the fabrication of a state-of-the-art X-band (∼8-11 GHz) RF photoinjector source aimed at producing psec high brightness electron bunches for advanced accelerator and coherent radiation generation studies

  1. Power electronics - key technology for renewable energy systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Iov, Florin; Kerekes, Tamas

    2011-01-01

    sources to renewable energy sources. Another is to use high efficient power electronics in power generation, power transmission/distribution and end-user application. This paper discuss trends of the most emerging renewable energy sources, wind energy and photovoltaics, which by means of power electronics...... as efficient as possible. Further, the emerging climate changes is arguing to find sustainable future solutions. Of many options, two major technologies will play important roles to solve parts of those future problems. One is to change the electrical power production from conventional, fossil based energy......The electrical energy consumption continues to grow and more applications are based on electricity. We can expect that more 60% of all energy consumption will be converted and used as electricity. Therefore, it is a demand that production, distribution and use of electrical energy are done...

  2. A comprehensible need of zinc oxide varistors in electronics technology

    International Nuclear Information System (INIS)

    Mehmood, F.S.

    2007-01-01

    A range of varistors, in terms of break down voltage, is required to protect integrated circuits, automotive systems and other modern electronics against transient over-voltages. There is a progressing need for the development and advancement of rugged and reliable varistor capable and proficient of working in harsh and callous environment like automotive Industry where greater than before use of electronics technology has led to improvements in equipment performance and presentation. There is a comprehensible need to combine triumphant and successable models developed at different length scales into an integrated framework that can be used to drive new research and guide experimental efforts and device development. The review of ZnO varistor in particular and metal-oxide varistors (MOVs) in general is presented In this article. (author)

  3. 3D Printing Technologies for Flexible Tactile Sensors toward Wearable Electronics and Electronic Skin

    Directory of Open Access Journals (Sweden)

    Changyong Liu

    2018-06-01

    Full Text Available 3D printing has attracted a lot of attention in recent years. Over the past three decades, various 3D printing technologies have been developed including photopolymerization-based, materials extrusion-based, sheet lamination-based, binder jetting-based, power bed fusion-based and direct energy deposition-based processes. 3D printing offers unparalleled flexibility and simplicity in the fabrication of highly complex 3D objects. Tactile sensors that emulate human tactile perceptions are used to translate mechanical signals such as force, pressure, strain, shear, torsion, bend, vibration, etc. into electrical signals and play a crucial role toward the realization of wearable electronics and electronic skin. To date, many types of 3D printing technologies have been applied in the manufacturing of various types of tactile sensors including piezoresistive, capacitive and piezoelectric sensors. This review attempts to summarize the current state-of-the-art 3D printing technologies and their applications in tactile sensors for wearable electronics and electronic skin. The applications are categorized into five aspects: 3D-printed molds for microstructuring substrate, electrodes and sensing element; 3D-printed flexible sensor substrate and sensor body for tactile sensors; 3D-printed sensing element; 3D-printed flexible and stretchable electrodes for tactile sensors; and fully 3D-printed tactile sensors. Latest advances in the fabrication of tactile sensors by 3D printing are reviewed and the advantages and limitations of various 3D printing technologies and printable materials are discussed. Finally, future development of 3D-printed tactile sensors is discussed.

  4. Electron beam technology for production of preparations of immobilized enzymes

    International Nuclear Information System (INIS)

    Gonchar, A.M.; Auslender, V.L.; Polyakov, V.A.

    1995-01-01

    Possibility of electron beam usage for proteases immobilization on 1,4-polyalkylene oxide (1,4-PAO) was studied to obtain biologically active complex for multi-purpose usage. It is shown that immobilization of Bacillus Subtilis protease is done due to free-radical linking of enzyme and carrier with formation of mycelium-like structures. Immobilization improves heat resistance of enzyme up to 60 centigrade without substrate and up to 80 centigrade in presence of substrate, widens range pH activity in comparison with non-immobilized forms. Immobilized proteases does not contain peroxides and long-live radicals. Our results permitted to create technologies for production of medical and veterinary preparations, active components for wool washing agents and leather fabrication technology

  5. 39 CFR 255.4 - Accessibility to electronic and information technology.

    Science.gov (United States)

    2010-07-01

    ... AND INFORMATION TECHNOLOGY § 255.4 Accessibility to electronic and information technology. (a) In... burden, that the electronic and information technology the agency procures allows— (1) Individuals with... 39 Postal Service 1 2010-07-01 2010-07-01 false Accessibility to electronic and information...

  6. Technology of silicon charged-particle detectors developed at the Institute of Electron Technology (ITE)

    Science.gov (United States)

    Wegrzecka, Iwona; Panas, Andrzej; Bar, Jan; Budzyński, Tadeusz; Grabiec, Piotr; Kozłowski, Roman; Sarnecki, Jerzy; Słysz, Wojciech; Szmigiel, Dariusz; Wegrzecki, Maciej; Zaborowski, Michał

    2013-07-01

    The paper discusses the technology of silicon charged-particle detectors developed at the Institute of Electron Technology (ITE). The developed technology enables the fabrication of both planar and epiplanar p+-ν-n+ detector structures with an active area of up to 50 cm2. The starting material for epiplanar structures are silicon wafers with a high-resistivity n-type epitaxial layer ( ν layer - ρ < 3 kΩcm) deposited on a highly doped n+-type substrate (ρ< 0,02Ωcm) developed and fabricated at the Institute of Electronic Materials Technology. Active layer thickness of the epiplanar detectors (νlayer) may range from 10 μm to 150 μm. Imported silicon with min. 5 kΩcm resistivity is used to fabricate planar detectors. Active layer thickness of the planar detectors (ν) layer) may range from 200 μm to 1 mm. This technology enables the fabrication of both discrete and multi-junction detectors (monolithic detector arrays), such as single-sided strip detectors (epiplanar and planar) and double-sided strip detectors (planar). Examples of process diagrams for fabrication of the epiplanar and planar detectors are presented in the paper, and selected technological processes are discussed.

  7. Evaluation of the functional performance and technical quality of an Electronic Documentation System of the Nursing Process.

    Science.gov (United States)

    de Oliveira, Neurilene Batista; Peres, Heloisa Helena Ciqueto

    2015-01-01

    To evaluate the functional performance and the technical quality of the Electronic Documentation System of the Nursing Process of the Teaching Hospital of the University of São Paulo. exploratory-descriptive study. The Quality Model of regulatory standard 25010 and the Evaluation Process defined under regulatory standard 25040, both of the International Organization for Standardization/International Electrotechnical Commission. The quality characteristics evaluated were: functional suitability, reliability, usability, performance efficiency, compatibility, security, maintainability and portability. The sample was made up of 37 evaluators. in the evaluation of the specialists in information technology, only the characteristic of usability obtained a rate of positive responses of less than 70%. For the nurse lecturers, all the quality characteristics obtained a rate of positive responses of over 70%. The staff nurses of the medical and surgical clinics with experience in using the system) and staff nurses from other units of the hospital and from other health institutions (without experience in using the system) obtained rates of positive responses of more than 70% referent to the functional suitability, usability, and security. However, performance efficiency, reliability and compatibility all obtained rates below the parameter established. the software achieved rates of positive responses of over 70% for the majority of the quality characteristics evaluated.

  8. The socio-technical organisation of community pharmacies as a factor in the Electronic Prescription Service Release Two implementation: a qualitative study

    Directory of Open Access Journals (Sweden)

    Harvey Jasmine

    2012-12-01

    Full Text Available Abstract Background The introduction of a new method of transmitting prescriptions from general practices to community pharmacies in England (Electronic Prescription Service Release 2 (EPS2 has generated debate on how it will change work practice. As EPS2 will be a key technical element in dispensing, we reviewed the literature to find that there were no studies on how social and technical elements come together to form work practice in community pharmacies. This means the debate has little point of reference. Our aim therefore was to study the ways social and technical elements of a community pharmacy are used to achieve dispensing through the development of a conceptual model on pharmacy work practice, and to consider how a core technical element such the EPS2 could change work practice. Method We used ethnographic methods inclusive of case-study observations and interviews to collect qualitative data from 15 community pharmacies that were in the process of adopting or were soon to adopt EPS2. We analysed the case studies thematically and used rigorous multi-dimensional and multi-disciplinary interpretive validation techniques to cross analyse findings. Results In practice, dispensing procedures were not designed to take into account variations in human and technical integration, and assumed that repetitive and collective use of socio-technical elements were at a constant. Variables such as availability of social and technical resources, and technical know-how of staff were not taken into account in formalised procedures. Yet community pharmacies were found to adapt their dispensing in relation to the balance of social and technical elements available, and how much of the social and technical elements they were willing to integrate into dispensing. While some integrated as few technical elements as possible, some depended entirely on technical artefacts. This pattern also applied to the social elements of dispensing. Through the conceptual

  9. Fundamental and Technical Challenges for a Compatible Design Scheme of Oxyfuel Combustion Technology

    Directory of Open Access Journals (Sweden)

    Chuguang Zheng

    2015-03-01

    Full Text Available Oxyfuel combustion with carbon capture and sequestration (CCS is a carbon-reduction technology for use in large-scale coal-fired power plants. Significant progress has been achieved in the research and development of this technology during its scaling up from 0.4 MWth to 3 MWth and 35 MWth by the combined efforts of universities and industries in China. A prefeasibility study on a 200 MWe large-scale demonstration has progressed well, and is ready for implementation. The overall research development and demonstration (RD&D roadmap for oxyfuel combustion in China has become a critical component of the global RD&D roadmap for oxyfuel combustion. An air combustion/oxyfuel combustion compatible design philosophy was developed during the RD&D process. In this paper, we briefly address fundamental research and technology innovation efforts regarding several technical challenges, including combustion stability, heat transfer, system operation, mineral impurities, and corrosion. To further reduce the cost of carbon capture, in addition to the large-scale deployment of oxyfuel technology, increasing interest is anticipated in the novel and next-generation oxyfuel combustion technologies that are briefly introduced here, including a new oxygen-production concept and flameless oxyfuel combustion.

  10. Flue gas cleaning by electron beam technology in 21st

    International Nuclear Information System (INIS)

    Xu Guang; Luo Jingyu; Zhang Ming

    2005-01-01

    China is paying great attention to the pollution caused by flue gases including sulfur oxides, nitrogen oxides, fine particles, and volatile organic compounds (VOC) for the environmental protection and sustainable development of China economy for 21st century. Among several promising processes, applicable to industrial scale, the electron beam (EB) scrubbing process can simultaneously remove SO 2 , NOx, PM-10 (particulate matter 10 μm or less in diameter), VOC and CO 2 from the flue gas is a new high technology combined with radiation chemistry and electron accelerator technique. The EB flue gas purification process consists of the producing ionization in the EB irradiated gases followed by the formation of free radicals and active species which ultimately forming foggy sulfur acid and nitrate acid. These acids react further with added ammonia to form ammonium sulfate and nitrates as by-products, which can be fertilizer usable in agriculture. The next stage for this technology is its optimization for the reduction of electricity energy consumption and an effective collection of by-products. Lastly the investment cost for EB method is shown to be the most economic compared with other competing methods. (S. Ohno)

  11. 16 CFR 6.152 - Program accessibility: Electronic and information technology.

    Science.gov (United States)

    2010-01-01

    ... information technology. 6.152 Section 6.152 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION... information technology. (a) When developing, procuring, maintaining, or using electronic and information... electronic and information technology allows, regardless of the type of medium of the technology: (1...

  12. Physics and technology of inertial fusion energy targets chambers and drivers. Proceedings of a technical meeting

    International Nuclear Information System (INIS)

    2005-09-01

    The third IAEA Technical Meeting on Physics and Technology of Inertial Fusion Energy Targets and Chambers took place 11-13 October 2004 in the Yousung Hotel Daejon, Republic of Korea. The first meeting was held in Madrid, Spain, 7-9 June 2000, and the second one in San Diego, California, 17-19 June 2002. Nuclear fusion has the promise of becoming an abundant energy source with good environmental compatibility. Excellent progress has been made in controlled nuclear fusion research on both magnetic and inertial approaches for plasma confinement. The IAEA plays a pro-active role to catalyze innovation and enhance worldwide commitment to fusion. This is done by creating awareness of the different concepts of magnetic as well as inertial confinement. The International Fusion Research Council (IFRC) supports the IAEA in the development of strategies to enhance fusion research in Member States. As part of the recommendations, a technical meeting on the physics and technology of inertial fusion energy (IFE) was proposed in one of the council meetings. The objective of the technical meeting was to contribute to advancing the understanding of targets and chambers for all proposed inertial fusion energy power plant designs. The topics to be covered were: Target design and physics, chamber design and physics, target fabrication injection and Tritium handling, assessment of safety, environment and economy aspect of IFE. It was recognized by the International Advisory Committee that the scope of the meeting should also include fusion drivers. The presentations of the meeting included target and chamber physics and technology for all proposed IFE plant concepts (laser driven, heavy-ion driven, Z-pinches, etc.). The final Research Coordination Meeting of the Coordinated Research Project on Elements of Power Plant Design for Inertial Fusion Energy, including further new results and achievements, followed the technical meeting. Twenty-nine participants from 12 countries participated

  13. Methods of technical and tactical training basketball players with hearing impairments using innovative technologies

    Directory of Open Access Journals (Sweden)

    Zh.L Kozina

    2014-06-01

    Full Text Available Purpose: to develop information technology for technical and tactical training of skilled basketball players with hearing impairments. Material : the study involved 24 women's national team athletes Ukrainian Basketball hearing impaired (age - 25-30 years. Technical protocols were processed 12 games from the World Cup and Europe, XXII Summer Deaflympics. Fixed number of shots and hit free throws, steals, rebounds and on its offensive rebounds, fouls and errors. Results : the developed system of tactical training basketball players with hearing impairments. Accentuation was made of the prevalence of method visibility while developing tactical interactions. The main result was the development of the author's method of video tutorials with animated illustrations. Also, use the lamp LS Line-3-65-12-C to control the training process athletes. Conclusions : there was a significant improvement in competitive activity athletes. Athletes performed significantly more hits from the foul line and successful shots from long range compared to main rivals. Also increased the number of interceptions in games. Application of information technology had an impact on the competitive result: basketball team of Ukraine took the second place in the Deaflympics in Sofia in 2013.

  14. Aviation Trends Related to Atmospheric Environment Safety Technologies Project Technical Challenges

    Science.gov (United States)

    Reveley, Mary S.; Withrow, Colleen A.; Barr, Lawrence C.; Evans, Joni K.; Leone, Karen M.; Jones, Sharon M.

    2014-01-01

    Current and future aviation safety trends related to the National Aeronautics and Space Administration's Atmospheric Environment Safety Technologies Project's three technical challenges (engine icing characterization and simulation capability; airframe icing simulation and engineering tool capability; and atmospheric hazard sensing and mitigation technology capability) were assessed by examining the National Transportation Safety Board (NTSB) accident database (1989 to 2008), incidents from the Federal Aviation Administration (FAA) accident/incident database (1989 to 2006), and literature from various industry and government sources. The accident and incident data were examined for events involving fixed-wing airplanes operating under Federal Aviation Regulation (FAR) Parts 121, 135, and 91 for atmospheric conditions related to airframe icing, ice-crystal engine icing, turbulence, clear air turbulence, wake vortex, lightning, and low visibility (fog, low ceiling, clouds, precipitation, and low lighting). Five future aviation safety risk areas associated with the three AEST technical challenges were identified after an exhaustive survey of a variety of sources and include: approach and landing accident reduction, icing/ice detection, loss of control in flight, super density operations, and runway safety.

  15. Mathematical model for estimating of technical and technological indicators of railway stations operation

    Directory of Open Access Journals (Sweden)

    D.M. Kozachenko

    2013-06-01

    Full Text Available Purpose. The article aims to create a mathematical model of the railway station functioning for the solving of problems of station technology development on the plan-schedule basis. Methodology. The methods of graph theory and object-oriented analysis are used as research methods. The model of the station activity plan-schedule includes a model of technical equipment of the station (plan-schedule net and a model of the station functioning , which are formalized on the basis of parametric graphs. Findings. The presented model is implemented as an application to the graphics package AutoCAD. The software is developed in Visual LISP and Visual Basic. Taking into account that the construction of the plan-schedule is mostly a traditional process of adding, deleting, and modifying of icons, the developed interface is intuitively understandable for a technologist and practically does not require additional training. Originality. A mathematical model was created on the basis of the theory of graphs and object-oriented analysis in order to evaluate the technical and process of railway stations indicators; it is focused on solving problems of technology development of their work. Practical value. The proposed mathematical model is implemented as an application to the graphics package of AutoCAD. The presence of a mathematical model allows carrying out an automatic analysis of the plan-schedule and, thereby, reducing the period of its creation more than twice.

  16. Remote technology related to the handling, storage and disposal of spent fuel. Proceedings of a technical committee meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    Reduced radiation exposure, greater reliability and cost savings are all potential benefits of the application of remote technologies to the handling of spent nuclear fuel. Remote equipment and technologies are used to some extent in all facilities handling fuel and high-level wastes whether they are for interim storage, processing/repacking, reprocessing or disposal. In view of the use and benefits of remote technologies, as well as recent technical and economic developments in the area, the IAEA organized the Technical Committee Meeting (TCM) on Remote Technology Related to the Handling, Storage and/or Disposal of Spent Fuel. Twenty-one papers were presented at the TCM, divided into five general areas: 1. Choice of technologies; 2. Use of remote technologies in fuel handling; 3. Use of remote technologies for fuel inspection and characterization; 4. Remote maintenance of facilities; and 5. Current and future developments. Refs, figs and tabs.

  17. Technical and economic aspects of electron beam installations for treatment of flue gases from power plants

    International Nuclear Information System (INIS)

    Chmielewski, A.G.; Iller, E.; Frank, N.W.

    1998-01-01

    The emission of environmental pollutants such as SO 2 and NO x into atmosphere from heavy industrial activity, and in particular from fossil fuel burning in electricity production, is arousing increasing concern. One of the three areas of the world most affected by the resultant acid rain lies in eastern and central Europe includes Poland, parts of Germany, the Czech Republic and Slovakia. A major contribution to this pollution comes from the burning of poor quality pit and brown coal with a high sulphur content. These effects, as well as polluted air reaching Poland from other countries, have begun to damage forests and cause public health concerns in regions of high industrial density. Many countries around the world have started to impose industrial emission limits and this move has generated renewed interest in finding viable and cost effective solutions to SO 2 and NO x pollution control. The conventional technologies - wet scrubbing for SO 2 and selective catalytic reduction for NO x now reached their full potential, these methods are not expected to provide further improvements in terms of efficiency or reduction in construction costs. A new technology being investigated for industrial scale commercial viability. One of them is the electron beam dry scrubbing process, which allows the simultaneous removal of SO 2 and NO x from industrial flue gases. The economical aspects of this technology are discussed in the presented paper

  18. The Role of Electronic Learning Technology in Networks Systems

    International Nuclear Information System (INIS)

    Abd ELhamid, A.; Ayad, N.M.A.; Fouad, Y.; Abdelkader, T.

    2016-01-01

    Recently, Electronic Learning Technology (ELT) has been widely spread as one of the new technologies in the world through using Information and Communication Technology (ICT). One of the strategies of ELT is Simulation, for instance Military and Medical simulations that are used to avoid risks and reduce Costs. A wireless communication network refers to any network not physically connected by cables, which enables the desired convenience and mobility for the user. Wireless communication networks have been useful in areas such as commerce, education and defense. According to the nature of a particular application, they can be used in home-based and industrial systems or in commercial and military environments. Historically, Mobile Ad-hoc Networks (MANET) have primarily been used for tactical military network related applications to improve battlefield communications/ survivability. MANET is a collection of wireless nodes that can dynamically be set up anywhere and anytime without using any pre-existing network infrastructure. Mobility in wireless networks basically refers to nodes changing its point of attachment to the network. Also, how the end terminals can move, there are many mobility models described the movement of nodes, many researchers use the Random Way point Mobility Model (RWPM). In this paper, a Graphical User Interface (GUI) for RWPM simulation is introduced as a proposal to be used through ELT Project. In the research area of computer and communications networks, simulation is a very useful technique for the behavior of networks

  19. Technical presentation

    CERN Document Server

    FP Department

    2009-01-01

    07 April 2009 Technical presentation by Leuze Electronics: 14.00 – 15.00, Main Building, Room 61-1-017 (Room A) Photoelectric sensors, data identification and transmission systems, image processing systems. We at Leuze Electronics are "the sensor people": we have been specialising in optoelectronic sensors and safety technology for accident prevention for over 40 years. Our dedicated staff are all highly customer oriented. Customers of Leuze Electronics can always rely on one thing – on us! •\tFounded in 1963 •\t740 employees •\t115 MEUR turnover •\t20 subsidiaries •\t3 production facilities in southern Germany Product groups: •\tPhotoelectric sensors •\tIdentification and measurements •\tSafety devices

  20. Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders.

    OpenAIRE

    Dooremalen, A.M.C.; van Hoof, J.; Weffers, H.T.G.; Wetzels, M.H.; Wouters, E.J.M.

    2014-01-01

    J. van Hoof, A.M.C. Dooremalen, M.H. Wetzels, H.T.G. Weffers, E.J.M. Wouters (2014) Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders. International Journal for Innovative Research in Science & Technology 1(3): 90-105

  1. Technical and economic assessments commercial success for IGCC technology in China

    International Nuclear Information System (INIS)

    Xiong, T.

    1998-01-01

    The experiences gained from several Integrated Gasification Combined Cycle (IGCC) demonstration plants operating in the US and Europe facilitate commercial success of this advanced coal-based power generation technology. However, commercialization of coal-based IGCC technology in the West, particularly in the US, is restricted due to the low price of natural gas. On the contrary, in China--the largest coal producer and consumer in the world--a lack of natural gas supply, strong demand for air pollution control and relatively low costs of manufacturing and construction provide tremendous opportunities for IGCC applications. The first Chinese IGCC demonstration project was initiated in 1994, and other potential IGCC projects are in planning. IGCC applications in re-powering, fuel switching and multi-generation also show a great market potential in China. However, questions for IGCC development in China remain; where are realistic opportunities for IGCC projects and how can these opportunities be converted into commercial success? The answers to these questions should focus on the Chinese market needs and emphasize economic benefits, not just clean, or power. High price of imported equipment, high financing costs, and the technical risk of first-of-a-kind installation barricade IGCC development in China. This paper presents preliminary technical and economic assessments for four typical IGCC applications in the Chinese marketplace: central power station, fuel switching, re-powering, and multi-generation. The major factors affecting project economics--such as plant cost, financing, prices of fuel and electricity and operating capacity factor--are analyzed. The results indicate that well-proven technology for versatile applications, preferred financing, reduction of the plant cost, environmental superiority and appropriate project structure are the key for commercial success of IGCC in China

  2. Electron cyclotron resonance plasmas and electron cyclotron resonance ion sources: Physics and technology (invited)

    International Nuclear Information System (INIS)

    Girard, A.; Hitz, D.; Melin, G.; Serebrennikov, K.

    2004-01-01

    Electron cyclotron resonance (ECR) ion sources are scientific instruments particularly useful for physics: they are extensively used in atomic, nuclear, and high energy physics, for the production of multicharged beams. Moreover, these sources are also of fundamental interest for plasma physics, because of the very particular properties of the ECR plasma. This article describes the state of the art on the physics of the ECR plasma related to multiply charged ion sources. In Sec. I, we describe the general aspects of ECR ion sources. Physics related to the electrons is presented in Sec. II: we discuss there the problems of heating and confinement. In Sec. III, the problem of ion production and confinement is presented. A numerical code is presented, and some particular and important effects, specific to ECR ion sources, are shown in Sec. IV. Eventually, in Sec. V, technological aspects of ECR are presented and different types of sources are shown

  3. Technological and organizational diversity and technical advance in the early history of the American semiconductor industry

    Science.gov (United States)

    Cohen, W.; Holbrook, D.; Klepper, S.

    1994-06-01

    This study examines the early years of the semiconductor industry and focuses on the roles played by different size firms in technologically innovative processes. A large and diverse pool of firms participated in the growth of the industry. Three related technological areas were chosen for in-depth analysis: integrated circuits, materials technology, and device packaging. Large business producing vacuum tubes dominated the early production of semiconductor devices. As the market for new devices grew during the 1950's, new firms were founded and existing firms from other industries, e.g. aircraft builders and instrument makers, began to pursue semiconductor electronics. Small firms began to cater to the emerging industry by supplying materials and equipment. These firms contributed to the development of certain aspects of one thousand firms that were playing some part in the semiconductor industry.

  4. Development of technical skills in Electrical Power Engineering students: A case study of Power Electronics as a Key Course

    Science.gov (United States)

    Hussain, I. S.; Azlee Hamid, Fazrena

    2017-08-01

    Technical skills are one of the attributes, an engineering student must attain by the time of graduation, as per recommended by Engineering Accreditation Council (EAC). This paper describes the development of technical skills, Programme Outcome (PO) number 5, in students taking the Bachelor of Electrical Power Engineering (BEPE) programme in Universiti Tenaga Nasional (UNITEN). Seven courses are identified to address the technical skills development. The course outcomes (CO) of the courses are designed to instill the relevant technical skills with suitable laboratory activities. Formative and summative assessments are carried out to gauge students’ acquisition of the skills. Finally, to measure the attainment of the technical skills, key course concept is used. The concept has been implemented since 2013, focusing on improvement of the programme instead of the cohort. From the PO attainment analysis method, three different levels of PO attainment can be calculated: from the programme level, down to the course and student levels. In this paper, the attainment of the courses mapped to PO5 is measured. It is shown that Power Electronics course, which is the key course for PO5, has a strong attainment at above 90%. PO5 of other six courses are also achieved. As a conclusion, by embracing outcome-based education (OBE), the BEPE programme has a sound method to develop technical psychomotor skills in the degree students.

  5. Technical advantages of disk laser technology in short and ultrashort pulse processes

    Science.gov (United States)

    Graham, P.; Stollhof, J.; Weiler, S.; Massa, S.; Faisst, B.; Denney, P.; Gounaris, E.

    2011-03-01

    This paper demonstrates that disk-laser technology introduces advantages that increase efficiency and allows for high productivity in micro-processing in both the nanosecond (ns) and picosecond (ps) regimes. Some technical advantages of disk technology include not requiring good pump beam quality or special wavelengths for pumping of the disk, high optical efficiencies, no thermal lensing effects and a possible scaling of output power without an increase of pump beam quality. With cavity-dumping, the pulse duration of the disk laser can be specified between 30 and hundreds of nanoseconds, but is independent of frequency, thus maintaining process stability. TRUMPF uses this technology in the 750 watts average power laser TruMicro 7050. High intensity, along with fluency, is important for high ablation rates in thinfilm removal. Thus, these ns lasers show high removal rates, above 60 cm2/s, in thin-film solar cell production. In addition, recent results in paint-stripping of aerospace material prove the green credentials and high processing rates inherent with this technology as it can potentially replace toxic chemical processes. The ps disk technology meanwhile is used in, for example, scribing of solar cells, wafer dicing and drilling injector nozzles, as the pulse duration is short enough to minimize heat input in the laser-matter interaction. In the TruMicro Series 5000, the multi-pass regenerative amplifier stage combines high optical-optical efficiencies together with excellent output beam quality for pulse durations of only 6 ps and high pulse energies of up to 0.25 mJ.

  6. High temperature gas cooled reactor technology development. Proceedings of a technical committee meeting

    International Nuclear Information System (INIS)

    1997-12-01

    The successful introduction of an advanced nuclear power plant programme depends on many key elements. It must be economically competitive with alternative sources of energy, its technical development must assure operational dependability, the support of society requires that it be safe and environmentally acceptable, and it must meet the regulatory standards developed for its use and application. These factors interrelate with each other, and the ability to satisfy the established goals and criteria of all of these requirements is mandatory if a country or a specific industry is to proceed with a new, advanced nuclear power system. It was with the focus on commercializing the high temperature gas cooled reactor (HTGR) that the IAEA's International Working Group on Gas Cooled Reactors recommended this Technical Committee Meeting (TCM) on HTGR Technology Development. Over the past few years, many Member States have instituted a re-examination of their nuclear power policies and programmes. It has become evident that the only realistic way to introduce an advanced nuclear power programme in today's world is through international co-operation between countries. The sharing of expertise and technical facilities for the common development of the HTGR is the goal of the Member States comprising the IAEA's International Working Group on Gas Cooled Reactors. This meeting brought together key representatives and experts on the HTGR from the national organizations and industries of ten countries and the European Commission. The state electric utility of South Africa, Eskom, hosted this TCM in Johannesburg, from 13 to 15 November 1996. This TCM provided the opportunity to review the status of HTGR design and development activities, and especially to identify international co-operation which could be utilized to bring about the commercialization of the HTGR

  7. Influence of information technologies on technical fitness of students in sport-oriented physical education

    Directory of Open Access Journals (Sweden)

    Zh.L. Kozina

    2016-02-01

    Full Text Available Purpose: to determine influence of information technologies in sport-oriented physical education on technical fitness of students, practicing football indoors. Material: in the researches students (boys - n=40 of 18-20 years’ age participated. Standard tests on physical condition were used. For determination of motor skills and abilities we used: juggling with ball; kick in pre-set sector of goal; shuttle run 4 x 10 meters with dribbling; kick for distance. Results: structural model of sport-oriented students’ physical education with application of information technologies has been formed. In the model all students are trained in sport-oriented academic groups by chosen kinds of sports (motor functioning. Such approach envisages holistic form of program material construction and unified algorithm of students’ progress assessment. Conclusions: the wholeness of sport-oriented physical education’s functioning is ensured at the account of application of information technologies. It permits to optimize motor skills’ training process. In this case single form of building of program material is created.

  8. Development of aromatic VOC control technology by electron beam hybrid

    International Nuclear Information System (INIS)

    Kim, Jo-Chun; Kim, Ki-Joon

    2006-01-01

    As a fundamental study, the decomposition of volatile organic compounds (VOCs) using electron beam (EB) irradiation has been extensively investigated. EB treatments of VOCs such as toluene and styrene are discussed. The degradation characteristics were intensively investigated under various concentrations and irradiation doses to determine and improve VOC removal efficiencies. This work illustrates that the removal efficiencies of aromatic VOCs generally increase as their concentrations decrease and the irradiation doses increase. Based on these basic studies, it was found that by-products produced from EB irradiation of VOCs would cause a secondary pollution problem. Therefore, a novel hybrid technology has been applied to control aromatic VOC emissions by annexing the catalyst technique with conventional treatment study using EB technology. The experiments were carried out using a bench-scale at first, then a pilot-scale system was followed. Toluene was selected as a typical VOC for EB hybrid control to investigate by-products, effects of ceramic and catalyst, and factors affecting overall efficiency of degradation. It was concluded that VOCs could be destroyed more effectively by a novel hybrid system than single EB irradiation. (author)

  9. Electron beam irradiation: novel technology for phytosanitary purposes

    International Nuclear Information System (INIS)

    Bhalla, Shashi; Srinivasan, K.; Dwivedi, J.; Gautam, S.; Sharma, Arun

    2015-01-01

    In the WTO regime, flow of agricultural commodities has increased, posing risk of inadvertent introduction of exotic pests. This can be minimized by undertaking quarantine measures. Quarantine/phytosanitary disinfestation treatments demand a very high level of security as the pest tolerance in quarantine is zero. Methyl bromide, a potent fumigant has been restricted in its use due to ozone depleting effect. Also, the conventional chemicals/fumigants being used world over are being restricted globally because of the various associated problems. Therefore, there is a need for an alternative ecofriendly strategy for controlling the pests. Irradiation, an approved technology by International Plant Protection Convention, appears to be a viable, nonchemical, residue-free strategy. Disinfestation of pulses with low energy electron irradiation potentially will have less deleterious effects on commodity quality than irradiation with other sources. Internationally, new radiation generating sources as Electron beam (EB) are being explored to meet import standards of quality and quarantine. The EB has a machine source and can be simply switched on or off. Irradiation of legume seeds viz., blackgram, greengram and soybean infested with pulse beetles (Callosobruchus maculatus and C. chinensis) at different doses at an energy level of 500 keV using the Accelerator facility at Raja Ramanna Centre for Advanced Technology, Indore revealed the dose-dependent effects on the insect growth parameters. Adult emergence from seeds infested with different stages was negligible and eggs laid by beetles that survived treatment did not develop into adults at higher doses. The lower doses viz., 170, 340 and 510 Gy on the other hand caused sterility effect on the insect but showed stimulatory effect on the physiological seed parameters . viz., seedling vigour and vigour index. Electron beam irradiation has a great potential for use in the disinfestation for phytosanitary purposes. Nevertheless

  10. Space Solar Power Exploratory Research and Technology (SERT) Technical Interchange Meeting 2 (SERT TIM 2)

    Science.gov (United States)

    Howell, Joe; Sanders, Clark W.

    2000-01-01

    The University of Alabama in Huntsville's (UAH) Propulsion Research Center hosted the Space Solar Power Exploratory Research & Technology (SERT) Technical Interchange Meeting TIM) 2 in Huntsville, Alabama December 7-10. 1999 with 126 people in attendance. The SERT program includes both competitively procured activities. which are being implemented through a portfolio of focused R&D investments--with the maximum leveraging of existing resources inside and outside NASA. and guided by these system studies. Axel Roth. Director of the Flight Projects Directorate NASA MSFC, welcomed the SERT TIM 2 participants and challenged them to develop the necessary technologies and demonstrations that will lead to Space Solar Power (SSP) International implementation. Joe Howell, NASA MSFC, reiterated the SERT TIM 2 objectives: 1) Refining and modeling systems approaches for the utilization of SSP concepts and technologies, ranging, from the near-term e.g. for space science, exploration and commercial space applications to the far-term (e. g. SSP for terrestrial markets), including systems concepts, technology, infrastructure (i.g., transportation), and economics. 2) Conducting technology research, development and demonstration activities to produce "proof- of-concept" validation of critical SSP elements for both the nearer and farther-term applications. 3) Initiating partnerships Nationality and Internationally that could be expanded, as appropriate, to pursue later SSP technology and applications (e.g., space science. colonization, etc.). Day one began with the NASA Centers presenting their SERT activities summary since SERT TIM 1 and wound up with a presentation by Masahiro Mori, NASDA titled "NASDA In-house Study for SSP". Demonstration for the Near-Term. Day two began with the SERT Systems Studies and Analysis reports resulting from NRA 8-23 followed by presentations of SERT Technology Demonstrations reports resulting from NRA 8-23. Day two closed with John Mankins presentation

  11. 76 FR 77738 - Telecommunications Act Accessibility Guidelines; Electronic and Information Technology...

    Science.gov (United States)

    2011-12-14

    ... Telecommunications Act Accessibility Guidelines and its Electronic and Information Technology Accessibility Standards... electronic and information technology covered by Section 508 of the Rehabilitation Act Amendments of 1998. 76.... 2011-07] RIN 3014-AA37 Telecommunications Act Accessibility Guidelines; Electronic and Information...

  12. Technology station in electronics at the Tshwane University of Technology: strengthening technological innovation activities amongst SMEs and students

    CSIR Research Space (South Africa)

    Jacobs, SJ

    2009-01-01

    Full Text Available that technology and science are closely intertwined (Gibbons et a/., 1994). Thus in this mode of the production of knowledge, innovation is often a process of moving back and forth between invention and/or design, development and testing, redesign... through-hole components and Component identification hardware, surface-mount components, surface-mount IC chip components, Metal Electrode Faces (MELFs), Small Outline Transistors (SOTs) and Discrete Packaging (DPAK). Handling in electronics assembly...

  13. New technologies applied to radiation protection training: Rp course for technical qualified expert

    International Nuclear Information System (INIS)

    Llorente Herranz, Cristina; Rodriguez, M.; Marco Arboli, Marisa

    2008-01-01

    This paper shows the development and results of the first Course for technical qualified expert in radiation protection (RP) using the advantages of Communication and Information Technologies (CITs). This project in modality b-learning has born as a result of the RP specialised course demand, the necessity of working-private life balance and working-training time combination as well as the geographic widespread of those interested. The methodology selected has been b-learning (blended learning), which consists of a mixture of e-learning plus face-to-face learning. The RP course for technical qualified RP expert has been designed for 10 weeks using online learning methodology and 2 days of face-to-face learning in a radioactive facility to take account practical sessions and the final knowledge evaluation. A multidisciplinary team of experts has elaborated the RP programme and the docent material, following national normative. The material consists of: a) Multimedia material with theoretical content to be visualised online; b) Additional material to be un-load or printed; c) Practical exercises within multimedia content; d) Practical online and face-to-face sessions. (author)

  14. Integrated Circuit Conception: A Wire Optimization Technic Reducing Interconnection Delay in Advanced Technology Nodes

    Directory of Open Access Journals (Sweden)

    Mohammed Darmi

    2017-10-01

    Full Text Available As we increasingly use advanced technology nodes to design integrated circuits (ICs, physical designers and electronic design automation (EDA providers are facing multiple challenges, firstly, to honor all physical constraints coming with cutting-edge technologies and, secondly, to achieve expected quality of results (QoR. An advanced technology should be able to bring better performances with minimum cost whatever the complexity. A high effort to develop out-of-the-box optimization techniques is more than needed. In this paper, we will introduce a new routing technique, with the objective to optimize timing, by only acting on routing topology, and without impacting the IC Area. In fact, the self-aligned double patterning (SADP technology offers an important difference on layer resistance between SADP and No-SADP layers; this property will be taken as an advantage to drive the global router to use No-SADP less resistive layers for critical nets. To prove the benefit on real test cases, we will use Mentor Graphics’ physical design EDA tool Nitro-SoC™ and several 7 nm technology node designs. The experiments show that worst negative slack (WNS and total negative slack (TNS improved up to 13% and 56%, respectively, compared to the baseline flow.

  15. 12 CFR 352.5 - Accessibility to electronic and information technology.

    Science.gov (United States)

    2010-01-01

    ... and information technology. (a) In accordance with section 508 of the Rehabilitation Act, the FDIC shall ensure, absent an undue burden, that the electronic and information technology the agency develops... or procurement of electronic and information technology that meets the standards published by the...

  16. Final Technical Report: "Representing Endogenous Technological Change in Climate Policy Models: General Equilibrium Approaches"

    Energy Technology Data Exchange (ETDEWEB)

    Ian Sue Wing

    2006-04-18

    The research supported by this award pursued three lines of inquiry: (1) The construction of dynamic general equilibrium models to simulate the accumulation and substitution of knowledge, which has resulted in the preparation and submission of several papers: (a) A submitted pedagogic paper which clarifies the structure and operation of computable general equilibrium (CGE) models (C.2), and a review article in press which develops a taxonomy for understanding the representation of technical change in economic and engineering models for climate policy analysis (B.3). (b) A paper which models knowledge directly as a homogeneous factor, and demonstrates that inter-sectoral reallocation of knowledge is the key margin of adjustment which enables induced technical change to lower the costs of climate policy (C.1). (c) An empirical paper which estimates the contribution of embodied knowledge to aggregate energy intensity in the U.S. (C.3), followed by a companion article which embeds these results within a CGE model to understand the degree to which autonomous energy efficiency improvement (AEEI) is attributable to technical change as opposed to sub-sectoral shifts in industrial composition (C.4) (d) Finally, ongoing theoretical work to characterize the precursors and implications of the response of innovation to emission limits (E.2). (2) Data development and simulation modeling to understand how the characteristics of discrete energy supply technologies determine their succession in response to emission limits when they are embedded within a general equilibrium framework. This work has produced two peer-reviewed articles which are currently in press (B.1 and B.2). (3) Empirical investigation of trade as an avenue for the transmission of technological change to developing countries, and its implications for leakage, which has resulted in an econometric study which is being revised for submission to a journal (E.1). As work commenced on this topic, the U.S. withdrawal

  17. European Power Electronic conference in Aalborg, Denmark - 1000 participants discussing the future energy technologies

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Munk-Nielsen, Stig

    2007-01-01

    The European Power Electronics and Adjustable Speed Drives conference with technical sponsorship of IEEE Industrial Electronic Society has been held in Aalborg, Denmark, during the first days of September 2007 with an overwhelming success and participation. It was hosted by Aalborg University's I...

  18. 23 CFR 950.5 - Requirement to use electronic toll collection technology.

    Science.gov (United States)

    2010-04-01

    ... shall use an electronic toll collection system as the method for collecting tolls from vehicle operators... 23 Highways 1 2010-04-01 2010-04-01 false Requirement to use electronic toll collection technology... TRANSPORTATION SYSTEMS ELECTRONIC TOLL COLLECTION § 950.5 Requirement to use electronic toll collection...

  19. Power Electronics for Distributed Energy Systems and Transmission and Distribution Applications: Assessing the Technical Needs for Utility Applications

    Energy Technology Data Exchange (ETDEWEB)

    Tolbert, L.M.

    2005-12-21

    Power electronics can provide utilities the ability to more effectively deliver power to their customers while providing increased reliability to the bulk power system. In general, power electronics is the process of using semiconductor switching devices to control and convert electrical power flow from one form to another to meet a specific need. These conversion techniques have revolutionized modern life by streamlining manufacturing processes, increasing product efficiencies, and increasing the quality of life by enhancing many modern conveniences such as computers, and they can help to improve the delivery of reliable power from utilities. This report summarizes the technical challenges associated with utilizing power electronics devices across the entire spectrum from applications to manufacturing and materials development, and it provides recommendations for research and development (R&D) needs for power electronics systems in which the U.S. Department of Energy (DOE) could make a substantial impact toward improving the reliability of the bulk power system.

  20. Electron beam facilities and technologies developed in the Institute of Nuclear Chemistry and Technology

    International Nuclear Information System (INIS)

    Chmielewski, A.G.; Walis, L.; Zimek, Z.

    1992-01-01

    The operation of the first electron accelerator has been started at Institute /former Institute for Nuclear Research/ in 1971. This LAE-13/9 accelerator is a two-section lineac with adjustable energy of electrons: 5 to 13 MeV and the beam power up to 9 kW. The main technologies developed on the basis of LAE-13/9 are: sterilization, manufacturing of thermoshrinkable materials and modification of semiconductors. The accelerator is operated 4000 hours per year and used for small scale production and services in these fields. The other problems investigated in laboratory scale are: food preservation and hygenization, hygenization of municipal sewage sludge, and bio-conversion of pig-farm wastes into animal fodder. The laboratory experiments are basis for pilot construction and other industrial applications. The mentioned technology of thermoshrinkable tube production was implemented in industrial scale at ZWUT Czluchow which factory is equipped in the accelerator ILU-6 /20 kW, 2 MeV/. On the basis of similar unit a technological installation was built at Institute. The plant is furnished with a conveyer and the rewinding machines for tubes and tapes manufacturing. This allows continuous production of these materials. The plant will start operation next year and linear accelerator /10 MeV, 15 kW/ for this purpose is already delivered. The pilot plant for food preservation and hygenization has been built. It is equipped in small pilot accelerator 10 MeV, 1 kW and will be furnished with 10 MeV, 10 kW lineac this year. Beside of this technological lines Institute is furnished in Van de Graff accelerator /2, MeV, 100 μA/ and another laboratory unit LAE-10 /10 MeV, 10-100 ns 2 us/ is under construction. (J.P.N.)

  1. Research reactor instrumentation and control technology. Report of a technical committee meeting

    International Nuclear Information System (INIS)

    1997-10-01

    The majority of research reactors operating today were put into operation 20 years ago, and some of them underwent modifications, upgrading and refurbishing since their construction to meet the requirements for higher neutron fluxes. However, a few of these ageing research reactors are still operating with their original instrumentation and control systems (I and C) which are important for reactor safety to guard against abnormal occurrences and reactor control involving startup, shutdown and power regulation. Worn and obsolete I and C systems cause operational problems as well as difficulties in obtaining replacement parts. In addition, satisfying the stringent safety conditions laid out by the nuclear regulatory bodies requires the modernization of research reactors I and C systems and integration of additional instrumentation units to the reactor. In order to clarify these issues and to provide some guidance to reactor operators on state-of-art technology and future trends for the I and C systems for research reactors, a Technical Committee Meeting on Technology and Trends for Research Reactor Instrumentation and Controls was held in Ljubljana, Slovenia, from 4 to 8 December 1995. This publication summarizes the discussions and recommendations resulting from that meeting. This is expected to benefit the research reactor operators planning I and C improvements. Refs, figs, tabs

  2. Newly available technologies present expanding opportunities for scientific and technical information exchange

    Science.gov (United States)

    Tolzman, Jean M.

    1993-01-01

    The potential for expanded communication among researchers, scholars, and students is supported by growth in the capabilities for electronic communication as well as expanding access to various forms of electronic interchange and computing capabilities. Increased possibilities for information exchange, collegial dialogue, collaboration, and access to remote resources exist as high-speed networks, increasingly powerful workstations, and large, multi-user computational facilities are more frequently linked and more commonly available. Numerous writers speak of the telecommunications revolution and its impact on the development and dissemination of knowledge and learning. One author offers the phrase 'Scholarly skywriting' to represent a new form of scientific communication that he envisions using electronic networks. In the United States (U.S.), researchers associated with the National Science Foundation (NSF) are exploring 'nationwide collaboratories' and 'digital collaboration.' Research supported by the U.S. National Aeronautics and Space Administration (NASA) points to a future where workstations with built-in audio, video monitors, and screen sharing protocols are used to support collaborations with colleagues located throughout the world. Instruments and sensors located worldwide will produce data streams that will be brought together, analyzed, and distributed as new findings. Researchers will have access to machines that can supply domain-specific information in addition to locator and directory assistance. New forms of electronic journals will emerge and provide opportunities for researchers and scientists to exchange information electronically and interactively in a range of structures and formats. Ultimately, the wide-scale use of these technologies in the dissemination of research results and the stimulation of collegial dialogue will change the way we represent and express our knowledge of the world. A new paradigm will evolve--perhaps a truly worldwide

  3. Columbus electronic freight management evaluation : achieving business benefits with EFM technologies.

    Science.gov (United States)

    2009-03-01

    Effective innovation in information technology (IT) may be the most important tool for the private and public sectors to respond to international supply chain capacity constraints and congestion. Electronic Freight Management (EFM) technologies are m...

  4. Nuclear science and technology at epoch of scientific and technical revolution

    International Nuclear Information System (INIS)

    Petros'yants, A.M.

    1979-01-01

    It is pointed out at the great revolutionizing influence of practical application of the nuclear energy with development of scientific and technical progress. Nowadays atomic energy being directed on the peaceful application of it is acquiring in the life of society significance which is difficult to overestimate. Completely new branch of industry has been created which is as to technology, culture of production and precision is concerned, exceeding all which had been created by mankind. Now it is difficult to manage without atomic energy in every branch of industry, in agriculture, medicine and scientific researches. History and modern state are stated of the development of main directions of nuclear science and technology, in particular: in the field of charged particles physics; nuclear physics; production of transuranium elements. Particular place is occupied by the works on creation of new energy sources, in particular, using controlled thermonuclear reactions and energy of fission. One of the forms of utilization of plasma processes is creation of MHD - generators. Structure has been shown of development of nuclear energetics in the CMEA member-states. Main types of power reactors have been listed and their characteristics have been given. Perspectives of nuclear ships building is given, as well as perspectives of applications of radioisotopes and radiations in different fields of science and technology, in particular, in different branches of industry and in nuclear medicine. The role of CMEA is stated in organizing and co-ordination of efforts of the countries of socialism in the field of development of peaceful applications of nuclear energy [ru

  5. Let's get technical! Gaming and technology for weight control and health promotion in children.

    Science.gov (United States)

    Baranowski, Tom; Frankel, Leslie

    2012-02-01

    Most children, including lower socioeconomic status and ethnic minority children, play video games, use computers, and have cell phones, and growing numbers have smart phones and electronic tablets. They are comfortable with, even prefer, electronic media. Many expect to be entertained and have a low tolerance for didactic methods. Thus, health promotion with children needs to incorporate more interactive media. Interactive media for weight control and health promotion among children can be broadly classified into web-based educational/therapeutic programs, tailored motivational messaging systems, data monitoring and feedback systems, active video games, and diverse forms of interactive multimedia experiences involving games. This article describes the primary characteristics of these different technological methods; presents the strengths and weaknesses of each in meeting the needs of children of different ages; emphasizes that we are in the earliest stages of knowing how best to design these systems, including selecting the optimal requisite behavioral change theories; and identifies high-priority research issues. Gaming and technology offer many exciting, innovative opportunities for engaging children and promoting diet and physical activity changes that can contribute to obesity prevention and weight loss maintenance. Research needs to clarify optimal procedures for effectively promoting change with each change procedure.

  6. Fuel and power resources based on energy-saving technologies and technical means in agriculture

    Directory of Open Access Journals (Sweden)

    A. V. Tikhomirov

    2015-01-01

    Full Text Available The state and efficiency of the use of the energy supply systems in agriculture were analyzed. It is demonstrated that grids and power equipment deterioration exceeds 30 percent, and fuel volume-efficiency ratio is not more than 35 percent in this sector. A considerable part of the country territory (mainly the northern one does not have centralized power supply. Decentralized cogeneration systems with extensive use of renewable energy sources and local energy recourses are highly efficient for this part. A necessity of development of methodology and recommendations for the selection of efficient systems and technical means of power supply to agricultural enterprises was substantiated with due consideration of their location, load intensity and distance from centralized grids. The most important indication of energy efficiency is energy intensity of products and energy inputs share in the production cost. Reserves for energy saving including the development of energy-efficient technologies and technical means, some of which have already been developed (equipment for lighting, microclimate, primary treatment and storage of products, disinfection or are at the completion stage were presented. Their implementation in agricultural production will make it possible to raise considerably the efficiency of the use of fuel and power resources and to reduce energy consumption. The conditions in which the use of decentralized power supply systems is most efficient were educed. The characteristics of related equipment and the specifics of its use at agricultural enterprises are described. The proposal and priority actions for the development and upgrading of power supply systems for agriculture have been elaborated.

  7. Technical issues of fabrication technologies of reduced activation ferritic/martensitic steels

    International Nuclear Information System (INIS)

    Tanigawa, Hiroyasu; Sakasegawa, Hideo; Hirose, Takanori

    2013-01-01

    Highlights: • The key technical issues of RAFM steel fabrication are the control of Ta, and deoxidation of the steel with a limited amount of Al addition. • Addition of Ta with poor deoxidation might results in the agglomeration of inclusions at 1/2t position. • ESR was proved to be effective removing Ta oxide inclusions and avoiding agglomeration of inclusions at 1/2t position, and achieving low oxygen concentration. -- Abstract: The key issue for DEMO application is that Reduced activation ferritic/martensitic (RAFM) steels fabrication technologies has to be highly assured, especially with respect to high availability, reliability and reduced activation capability on the DEMO level fabrication, which requires not a few tons but thousand tons RAFM fabrication. One of the key technical issues of RAFM fabrication is the control of Ta, and deoxidation of the steel with a limited amount of Al addition. The series of F82H (Fe–8Cr–2W–V, Ta) melting revealed that Ta have tendency to form oxide on melting process, and this will have large impact on reliability of the steels. Al is also the key elements, as it is commonly used for deoxidation of steels, and achieving lower oxygen level is essential to obtain good mechanical properties, but the maximum concentration of Al is limited in view of reduced activation capability. These tendency and limitation resulted in the Ta oxide agglomeration in the middle of plate, but the remelting process, ESR (electro slag remelting), was found to be successful on removing those Ta oxides

  8. An AES Study of the Room Temperature Surface Conditioning of Technological Metal Surfaces by Electron Irradiation

    CERN Document Server

    Scheuerlein, C; Taborelli, M; Brown, A; Baker, M A

    2002-01-01

    The modifications to technological copper and niobium surfaces induced by 2.5 keV electron irradiation have been investigated in the context of the conditioning process occurring in particle accelerator ultra high vacuum systems. Changes in the elemental surface composition have been found using Scanning Auger Microscopy (SAM) by monitoring the carbon, oxygen and metal Auger peak intensities as a function of electron irradiation in the dose range 10-6 to 10-2 C mm-2. The surface analysis results are compared with electron dose dependent secondary electron and electron stimulated desorption yield measurements. Initially the electron irradiation causes a surface cleaning through electron stimulated desorption, in particular of hydrogen. During this period both the electron stimulated desorption and secondary electron yield decrease as a function of electron dose. When the electron dose exceeds 10-4 C mm-2 electron stimulated desorption yields are reduced by several orders of magnitude and the electron beam indu...

  9. Electronic apex locator: A comprehensive literature review — Part II: Effect of different clinical and technical conditions on electronic apex locator′s accuracy

    Directory of Open Access Journals (Sweden)

    Hamid Razavian

    2014-01-01

    Full Text Available Introduction: To investigate the effects of different clinical and technical conditions on the accuracy of electronic apex locators (EALs. Materials and Methods: "Tooth apex," "dental instrument," "odontometry," "electronic medical," and "electronic apex locator" were searched as primary identifiers via Medline/PubMed, Cochrane library, and Scopus data base up to 30 July 2013. Original articles that fulfilled the inclusion criteria were selected and reviewed. Results: Out of 402 relevant studies, 183 were selected based on the inclusion criteria. In this part, 75 studies are presented. Pulp vitality conditions and root resorption, types of files and irrigating materials do not affect an EAL′s accuracy; however, the file size and foramen diameter can affect its accuracy. Conclusions: Various clinical conditions such as the file size and foramen diameter may affect EALs′ accuracy. However, more randomized clinical trials are needed for definitive conclusion.

  10. Improving Forsyth Technical Community College's Ability to Develop and Maintain Partnerships: Leveraging Technology to Develop Partnerships

    Science.gov (United States)

    Murdock, Alan K.

    2017-01-01

    Forsyth Technical Community College (FTCC) face a shortage of funding to meet the demands of students, faculty, staff and businesses. Through this practitioner research, the utilization of the college's current customer relationship management (CRM) database advanced. By leveraging technology, the researcher assisted the college in meeting the…

  11. Self-Study as an Emergent Methodology in Career and Technical Education, Adult Education and Technology: An Invitation to Inquiry

    Science.gov (United States)

    Hawley, Todd S.; Hostetler, Andrew L.

    2017-01-01

    In this manuscript, the authors explore self-study as an emerging research methodology with the potential to open up spaces of inquiry for researchers, graduate students, and teachers in a broad array of fields. They argue that the fields of career and technical education (CTE), adult education and technology can leverage self-study methodology in…

  12. Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders.

    NARCIS (Netherlands)

    A.M.C. Dooremalen; J. van Hoof; H.T.G. Weffers; M.H. Wetzels; MD E.J.M. Wouters

    2014-01-01

    J. van Hoof, A.M.C. Dooremalen, M.H. Wetzels, H.T.G. Weffers, E.J.M. Wouters (2014) Exploring technological and architectural solutions for nursing home residents, care professionals and technical staff: Focus groups with professional stakeholders. International Journal for Innovative Research in

  13. Automation of the Comprehensive Science Library: Promotion of Scientific and Technological Information Service, Republic of Korea. [Restricted Technical Report.

    Science.gov (United States)

    Mackenzie, A. Graham

    This technical report presents recommendations and plans which are the result of a mission undertaken as part of a project to promote a scientific and technological information service and establish a popular science resource center in Korea. The mission's main emphasis was to help Korean authorities and the United Nations Development Programme…

  14. Comparative analysis of concentrating solar power and photovoltaic technologies: Technical and environmental evaluations

    International Nuclear Information System (INIS)

    Desideri, U.; Zepparelli, F.; Morettini, V.; Garroni, E.

    2013-01-01

    Highlights: ► Life cycle was assessed for both concentrated solar power and photovoltaic systems. ► The PV plant has a higher environmental impact than the CSP plant. ► The Global Warming Potential is lower for the CSP than for the PV plant. ► The energy payback time is lower for the CSP than for the PV plant. -- Abstract: Solar energy is an important alternative energy source to fossil fuels and theoretically the most available energy source on the earth. Solar energy can be converted into electric energy by using two different processes: by means of thermodynamic cycles and the photovoltaic conversion. Solar thermal technologies, sometimes called thermodynamic solar technologies, operating at medium (about 500 °C) and high temperatures (about 1000 °C), have recently attracted a renewed interest and have become one of the most promising alternatives in the field of solar energy utilization. Photovoltaic conversion is very interesting, although still quite expensive, because of the absence of moving components and the reduced operating and management costs. The main objectives of the present work are: •to carry out comparative technical evaluations on the amount of electricity produced by two hypothetical plants, located on the same site, for which a preliminary design was made: a solar thermal power plant with parabolic trough collectors and a photovoltaic plant with a single-axis tracking system; •to carry out a comparative analysis of the environmental impact derived from the processes of electricity generation during the whole life cycle of the two hypothetical power plants. First a technical comparison between the two plants was made assuming that they have the same nominal electric power and then the same total covered surface. The methodology chosen to evaluate the environmental impact associated with the power plants is the Life Cycle Assessment (LCA). It allows to analyze all the phases of the life cycle of the plants, from the extraction of

  15. Raman scattering and associated fast electron production. Final technical report, April 16, 1984-April 15, 1985

    International Nuclear Information System (INIS)

    Brooks, R.D.; Pietrzyk, Z.A.

    1985-08-01

    High energy electrons in plasmas have been attributed to various causes including trapping by electron plasma waves created by stimulated Raman scattering. A theory, consistent with experimental results, based on the acceleration of trapped electrons by such electron plasma waves as they propagate in the presence of a density gradient away from the region where they are created is presented. Single particle simulations show accelerating voltages as high as 20 GV/m

  16. A review on remote monitoring technology applied to implantable electronic cardiovascular devices.

    Science.gov (United States)

    Costa, Paulo Dias; Rodrigues, Pedro Pereira; Reis, António Hipólito; Costa-Pereira, Altamiro

    2010-12-01

    Implantable electronic cardiovascular devices (IECD) include a broad spectrum of devices that have the ability to maintain rhythm, provide cardiac resynchronization therapy, and/or prevent sudden cardiac death. The incidence of bradyarrhythmias and other cardiac problems led to a broader use of IECD, which turned traditional follow-up into an extremely heavy burden for healthcare systems to support. Our aim was to assess the impact of remote monitoring on the follow-up of patients with IECD. We performed a review through PubMed using a specific query. The paper selection process included a three-step approach in which title, abstract, and cross-references were analyzed. Studies were then selected using previously defined inclusion criteria and analyzed according to the country of origin of the study, year, and journal of publication; type of study; and main issues covered. Twenty articles were included in this review. Eighty percent of the selected papers addressed clinical issues, from which 94% referred clinical events identification, clinical stability, time savings, or physician satisfaction as advantages, whereas 38% referred disadvantages that included both legal and technical issues. Forty-five percent of the papers referred patient issues, from which 89% presented advantages, focusing on patient acceptance/satisfaction, and patient time-savings. The main downsides were technical issues but patient privacy was also addressed. All the papers dealing with economic issues (20%) referred both advantages and disadvantages equally. Remote monitoring is presently a safe technology, widely accepted by patients and physicians, for its convenience, reassurance, and diagnostic potential. This review summarizes the principles of remote IECD monitoring presenting the current state-of-the-art. Patient safety and device interaction, applicability of current technology, and limitations of remote IECD monitoring are also addressed. The use of remote monitor should consider

  17. E-KIT: An Electronic-Knowledge Information Tool for Organizing Site Information and Improving Technical Communication with Stakeholders - 13082

    International Nuclear Information System (INIS)

    Kautsky, Mark; Findlay, Richard C.; Hodges, Rex A.

    2013-01-01

    Managing technical references for projects that have long histories is hampered by the large collection of documents, each of which might contain discrete pieces of information relevant to the site conceptual model. A database application has been designed to improve the efficiency of retrieving technical information for a project. Although many databases are currently used for accessing analytical and geo-referenced data, applications designed specifically to manage technical reference material for projects are scarce. Retrieving site data from the array of available references becomes an increasingly inefficient use of labor. The electronic-Knowledge Information Tool (e-KIT) is designed as a project-level resource to access and communicate technical information. The e-KIT is a living tool that grows as new information becomes available, and its value to the project increases as the volume of site information increases. Having all references assembled in one location with complete reference citations and links to elements of the site conceptual model offers a way to enhance communication with outside groups. The published and unpublished references are incorporated into the e-KIT, while the compendium of references serves as a complete bibliography for the project. (authors)

  18. E-KIT: An Electronic-Knowledge Information Tool for Organizing Site Information and Improving Technical Communication with Stakeholders - 13082

    Energy Technology Data Exchange (ETDEWEB)

    Kautsky, Mark [U.S. Department of Energy Office of Legacy Management, 2597 Legacy Way, Grand Junction CO 81503 (United States); Findlay, Richard C.; Hodges, Rex A. [Stoller LMS Team, 2597 Legacy Way, Grand Junction CO 81503 (United States)

    2013-07-01

    Managing technical references for projects that have long histories is hampered by the large collection of documents, each of which might contain discrete pieces of information relevant to the site conceptual model. A database application has been designed to improve the efficiency of retrieving technical information for a project. Although many databases are currently used for accessing analytical and geo-referenced data, applications designed specifically to manage technical reference material for projects are scarce. Retrieving site data from the array of available references becomes an increasingly inefficient use of labor. The electronic-Knowledge Information Tool (e-KIT) is designed as a project-level resource to access and communicate technical information. The e-KIT is a living tool that grows as new information becomes available, and its value to the project increases as the volume of site information increases. Having all references assembled in one location with complete reference citations and links to elements of the site conceptual model offers a way to enhance communication with outside groups. The published and unpublished references are incorporated into the e-KIT, while the compendium of references serves as a complete bibliography for the project. (authors)

  19. Packaging Technologies for High Temperature Electronics and Sensors

    Science.gov (United States)

    Chen, Liangyu; Hunter, Gary W.; Neudeck, Philip G.; Beheim, Glenn M.; Spry, David J.; Meredith, Roger D.

    2013-01-01

    This paper reviews ceramic substrates and thick-film metallization based packaging technologies in development for 500degC silicon carbide (SiC) electronics and sensors. Prototype high temperature ceramic chip-level packages and printed circuit boards (PCBs) based on ceramic substrates of aluminum oxide (Al2O3) and aluminum nitride (AlN) have been designed and fabricated. These ceramic substrate-based chiplevel packages with gold (Au) thick-film metallization have been electrically characterized at temperatures up to 550degC. A 96% alumina based edge connector for a PCB level subsystem interconnection has also been demonstrated recently. The 96% alumina packaging system composed of chip-level packages and PCBs has been tested with high temperature SiC devices at 500degC for over 10,000 hours. In addition to tests in a laboratory environment, a SiC JFET with a packaging system composed of a 96% alumina chip-level package and an alumina printed circuit board mounted on a data acquisition circuit board was launched as a part of the MISSE-7 suite to the International Space Station via a Shuttle mission. This packaged SiC transistor was successfully tested in orbit for eighteen months. A spark-plug type sensor package designed for high temperature SiC capacitive pressure sensors was developed. This sensor package combines the high temperature interconnection system with a commercial high temperature high pressure stainless steel seal gland (electrical feed-through). Test results of a packaged high temperature capacitive pressure sensor at 500degC are also discussed. In addition to the pressure sensor package, efforts for packaging high temperature SiC diode-based gas chemical sensors are in process.

  20. New Electronic Technology Applied in Flexible Organic Optical System

    Directory of Open Access Journals (Sweden)

    Andre F. S. Guedes

    2014-02-01

    Full Text Available The synthesis and application of new organic materials, nanostructured, for developing technology based on organic devices, have been the main focus of the scientific community. In recent years, the first polymeric electronics products have entered the market (organic semiconductor materials and there are some electrochromic devices among them that have been called smart windows, once they control the passage of light or heat through a closed environment as an ordinary window. The main functional aspect of electrochromic devices, when being used in architectural and automotive industry, is to control the passage of light and temperature with thermal and visual comfort. These devices can be flexible and very thin, not containing heavy metals, and formed by layers of organic material deposited in several architectures. In this study, the electro-deposition of organic materials in the Polyaniline, PANI case, which provide stability in optical and electrical parameters, was utilized with the means of developing prototypes of organic electrochromic devices. These materials were characterized by: ultraviolet-visible spectroscopy absorption (UV-Vis, measurement of thickness (MT and electrical measurements (EM. This study aims to establish the relationship between the thickness of the active layer and the value of the electrical resistivity of the layer deposited through an electro-deposition technique. The experimental results enabled the equating of the electrical resistivity related to the thickness of the deposited layer. The linear fit of these results has expressed the thickness of the conducting layer, α, and the lowest value of the electrical resistivity, β, associated with the gap between the valence band and the conduction band. Thus, the results have demonstrated that, when the layer of organic material is completely conductive, we may obtain the thickness of the organic material deposited on the substrate.

  1. Integration Science and Technology of Silicon-Based Ceramics and Composites:Technical Challenges and Opportunities

    Science.gov (United States)

    Singh, M.

    2013-01-01

    Ceramic integration technologies enable hierarchical design and manufacturing of intricate ceramic and composite parts starting with geometrically simpler units that are subsequently joined to themselves and/or to metals to create components with progressively higher levels of complexity and functionality. However, for the development of robust and reliable integrated systems with optimum performance for high temperature applications, detailed understanding of various thermochemical and thermomechanical factors is critical. Different technical approaches are required for the integration of ceramic to ceramic and ceramic to metal systems. Active metal brazing, in particular, is a simple and cost-effective method to integrate ceramic to metallic components. Active braze alloys usually contain a reactive filler metal (e.g., Ti, Cr, V, Hf etc) that promotes wettability and spreading by inducing chemical reactions with the ceramics and composites. In this presentation, various examples of brazing of silicon nitride to themselves and to metallic systems are presented. Other examples of joining of ceramic composites (C/SiC and SiC/SiC) using ceramic interlayers and the resulting microstructures are also presented. Thermomechanical characterization of joints is presented for both types of systems. In addition, various challenges and opportunities in design, fabrication, and testing of integrated similar (ceramic-ceramic) and dissimilar (ceramic-metal) material systems will be discussed. Potential opportunities and need for the development of innovative design philosophies, approaches, and integrated system testing under simulated application conditions will also be presented.

  2. The appropriation of contents in the subject Technology of Masonry in Technical and Professional Education

    Directory of Open Access Journals (Sweden)

    Felix Noel Hernández Torres

    2017-07-01

    Full Text Available In technical and professional education, the study on how to make teaching and learning more efficient is a preponderant place. In this sense, the purpose of the work was to base basic aspects of the process of appropriation of contents in the subject of Masonry Technology, during the training of the qualified worker of this specialty for his competent insertion in the labor world. The research process was carried out on a dialectical-materialist basis and methods were used from the theoretical level, from the empirical level and statistical-mathematical, such as the system approach, modeling, analysis and synthesis, observation, interview and documentary analysis and from the descriptive statistics the percentage analysis, which allowed the diagnosis of the educational reality and the evidence of the practical validity of the work. The level of appropriation of content was based on the extent to which students were able to show the skills required during the solution, in practice, of the dissimilar problems that in the constructive scope arose in the context school-business.

  3. Technical assessment of discarded tires gasification as alternative technology for electricity generation.

    Science.gov (United States)

    Machin, Einara Blanco; Pedroso, Daniel Travieso; de Carvalho, João Andrade

    2017-10-01

    Concern about contamination associated with the disposal of tires has led to the search for technologies to reuse discarded tires, which include the use of Tire Derived Fuel (TDF) as fuel in advanced thermal-conversion processes, this allows the energy use of these wastes at affordable costs and reduces the environmental impact on scrap tires disposal. A theoretical assessment of the technical viability of TDF gasification for electric and thermal power generation, from the producer gas combustion in an internal combustion engine and in a gas turbine, was performed. The combustion of producer gas derived from the gasification of TDF in an internal combustion engine driving a generator (ICE-G) appears as the more efficient route for electricity generation when compared with the efficiency obtained with the use of gas turbine (GT-G). A higher global efficiency, considering the electric and thermal generation efficiency can be expected with the use of TDF producer gas in GT-G, where is expected an overall efficiency of 77.49%. The assessment shows that is possible produces up to 7.67MJ and 10.62MJ of electric and thermal energy per kilogram of TDF gasified using an ICE-G and up to 6.06MJ and 13.03MJ of electric and thermal energy respectively per kilogram of gasified TDF using a GT-G. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Long-term high-level waste technology. Composite quarterly technical report, January-March 1981

    International Nuclear Information System (INIS)

    Cornman, W.R.

    1981-08-01

    This composite quarterly technical report summarizes work performed at participating sites to immobilize high-level radioactive wastes. The report is structured along the lines of the Work Breakdown Structure adopted for use in the High-Level Waste Management Technology program. These are: (1) program management and support with subtasks of management and budget, environmental and safety assessments, and other support; (2) waste preparation with subtasks of in-situ storage or disposal, waste retrieval, and separation and concentration; (3) waste fixation with subtasks of waste form development and characterization, and process and equipment development; and (4) final handling with subtasks of canister development and characterization and onsite storage or disposal. Some of the highlights are: preliminary event trees defining possible accidents were completed in the safety assessment of continued in-tank storage of high-level waste at Hanford; two low-cost waste forms (tailored concrete and bitumen) were investigated as candidate immobilization forms at the Hanford in-situ disposal studies of high-level waste; in comparative impact tests at the same impact energy per specimen volume, the same mass of respirable sizes was observed at ANL for SRL Frit 131 glass, SYNROC B ceramic, and SYNROC D ceramic; leaching tests were conducted on alkoxide glasses; glass-ceramic, concrete, and SYNROC D; a process design description was written for the tailored ceramic process

  5. Impact of technical and technological changes on energy efficiency of production company - case study

    Science.gov (United States)

    Szwedzka, K.; Gruszka, J.; Szafer, P.

    2016-08-01

    Improving energy efficiency is one of the strategic objectives of the European Union for rational energy economy. To make efforts to improve energy efficiency have been obliged both small and large end-users. This article aims to show the possibilities of improving energy efficiency by introducing technical and technological process changes of pine lumber drying. The object of the research is process of drying lumber implemented in a production company, which is a key supplier of large furniture manufacturer. Pine lumber drying chamber consume about 45% of total electricity in sawmill. According to various sources, drying of 1m3 of lumber uses about 3060kWh and is dependent of inter alia: the drying process itself, the factors affecting the processing time and the desired output moisture content of the timber. The article proposals for changes in the process of drying lumber pine have been positively validated in the company, and as a result their energy consumption per 1 m3 of product declined by 18%.

  6. For optimum safety technologies: understanding relations between the different national authorities and the technical support organizations

    International Nuclear Information System (INIS)

    Mahmoud, N.S.; Mostafa Aziz, Mostafa

    2010-01-01

    TSOs describe expert independent organizations, which provide supports for government, regulatory authorities, utilities and industry. The TSO must dispose different competences and objectives in order to deliver to the four independent authorities the technical and scientific knowledge. This comprehensive knowledge, from TSO, should perform through the research and development activities (R and D). Concerning the government, TSOs consider the R and D on the management procedures to characterize the links, to differentiate roles to prevent the overlapping efforts, and finally to build a central data bank in nuclear technologies for the other three authorities. For regulatory organizations, R and D are involved in the regulatory requirements and surveillance processes. On the other side R and D, in case of utilities, activities should focus on the improvement of safety operations for nuclear power and its new generations, and for other nuclear/radiological facilities. Finally, the forth TSOs has R and D targets that should concentrate mainly on material, efficiency, and durability of different equipment and parts involved in the nuclear activities during manufacturing. (author)

  7. CERN Technical Training 2006: Software and System Technologies Curriculum - Scheduled Course Sessions (October-December 2006)

    CERN Multimedia

    2006-01-01

    he Software and System Technologies Curriculum of the CERN Technical Training Programme offers comprehensive training in C++, Java, Perl, Python, XML, OO programming, JCOP/PVSS, database design and Oracle. In the PERL, C++, OO and Java course series there are some places available on the following course sessions, scheduled until the end of this year: Object-Oriented Analysis and Design using UML: 17-19 October 2006 (3 days) JAVA 2 Enterprise Edition - Part 1: Web Applications: 19-20 October 2006 (2 days) JAVA - Level 1: 30 Oct. -1 Nov. 2006 (3 days) PERL 5 - Advanced Aspects: 2 November 2006 (1 day) C++ Programming Part 1 - Introduction to Object-Oriented Design and Programming: 14-16 November 2006 (3 days) JAVA - Level 2: 4-7 December 2006 (4 days) C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls: 12-15 December 2006 (4 days) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans : 18.20 December 2006 (3 days) All the above sessions will be given in English, at the CERN Training Centre....

  8. CERN Technical Training 2006: Software and System Technologies Curriculum - Scheduled Course Sessions (August-December 2006)

    CERN Multimedia

    2006-01-01

    The Software and System Technologies Curriculum of the CERN Technical Training Programme offers comprehensive training in C++, Java, Perl, Python, XML, OO programming, JCOP/PVSS, database design and Oracle. In the PERL, C++, OO and Java course series there are some places available on the following course sessions, scheduled until the end of this year: PERL 5 - Introduction: 31.8-1.9.2006 (2 days) C++ for Particle Physicists: 16-20.10.2006 (6 half days, the popular course given by Paul Kunz) Object-Oriented Analysis and Design using UML: 17-19.10.2006 (3 days) JAVA 2 Enterprise Edition - Part 1: Web Applications: 19-20.10.2006 (2 days) JAVA - Level 1: 30.10-1.11.2006 (3 days) PERL 5 - Advanced Aspects: 2.11.2006 (1 day) C++ Programming Part 1 - Introduction to Object-Oriented Design and Programming: 14-16.11.2006 (3 days) JAVA - Level 2: 4-7.12.2006 (4 days) C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls: 12-15.12.2006 (4 days) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBea...

  9. CERN Technical Training 2006: Software and System Technologies Curriculum - Scheduled Course Sessions (October 2006-March 2007)

    CERN Multimedia

    2006-01-01

    The Software and System Technologies Curriculum of the CERN Technical Training Programme offers comprehensive training in C++, Java, Perl, Python, XML, OO programming, JCOP/PVSS, database design and Oracle. In the Oracle, C++, OO and Java course series there are some places available on the following course sessions, currently scheduled until March 2007: Object-Oriented Analysis and Design using UML: 17-19 October 2006 (3 days) JAVA - Level 1: 30 October - 1 November 2006 (3 days) C++ Programming Part 1 - Introduction to Object-Oriented Design and Programming: 14-16 November 2006 (3 days) Oracle Database Server Administration: 23-29 November 2007 (5 days) JAVA - Level 2: 4-7 December 2006 (4 days) C++ Programming Part 2 - Advanced C++ and its Traps and Pitfalls: 12-15 December 2006 (4 days) JAVA 2 Enterprise Edition - Part 2: Enterprise JavaBeans: 18-20 December 2006 (3 days) JAVA 2 Enterprise Edition - Part 1: Web Applications: 15-16 January 2007 (2 days) C++ Programming Part 3 - Templates and the STL (St...

  10. Directed technical change and the adoption of CO2 abatement technology. The case of CO2 capture and storage

    International Nuclear Information System (INIS)

    Otto, Vincent M.; Reilly, John

    2008-01-01

    This paper studies the cost-effectiveness of combining traditional environmental policy, such as CO 2 -trading schemes, and technology policy that has aims of reducing the cost and speeding the adoption of CO 2 abatement technology. For this purpose, we develop a dynamic general equilibrium model that captures empirical links between CO 2 emissions associated with energy use, directed technical change and the economy. We specify CO 2 capture and storage (CCS) as a discrete CO 2 abatement technology. We find that combining CO 2 -trading schemes with an adoption subsidy is the most effective instrument to induce adoption of the CCS technology. Such a subsidy directly improves the competitiveness of the CCS technology by compensating for its markup over the cost of conventional electricity. Yet, introducing R and D subsidies throughout the entire economy leads to faster adoption of the CCS technology as well and in addition can be cost-effective in achieving the abatement target. (author)

  11. The outlook of innovative optical-electronic technologies implementation in transportation

    Science.gov (United States)

    Shilina, Elena V.; Ryabichenko, Roman B.

    2005-06-01

    Information and telecommunication technologies (ITT) are already tool economic development of society and their role will grow. The first task is providing of information security of ITT that is necessary for it distribution in "information" society. The state policy of the leading world countries (USA, France, Japan, Great Britain and China) is focused on investment huge funds in innovative technologies development. Within the next 4-6 years the main fiber-optic transfer lines will have data transfer speed 40 Gbit/s, number of packed channels 60-200 that will provide effective data transfer speed 2,4-8 Tbit/s. Photonic-crystalline fibers will be promising base of new generation fiber-optic transfer lines. The market of information imaging devices and digital photo cameras will be grown in 3-5 times. Powerful lasers based on CO2 and Nd:YAG will be actively used in transport machinery construction when producing aluminum constructions of light rolling-stock. Light-emitting diodes (LEDs) will be base for energy saving and safety light sources used for vehicles and indoor lighting. For example, in the USA cost reducing for lighting will be 200 billion dollars. Implementation analysis of optic electronic photonic technologies (OPT) in ground and aerospace systems shows that they provide significant increasing of traffic safety, crew and passengers comfort with help of smart vehicles construction and non-contact dynamic monitoring both transport facilities (for example, wheel flanges) and condition of rail track (road surface), equipping vehicles with night vision equipment. Scientific-technical programs of JSC "RZD" propose application of OPT in new generation systems: axle-box units for coaches and freight cars monitoring when they are moved, track condition analysis, mechanical stress and permanent way irregularity detection, monitoring geometric parameters of aerial contact wire, car truck, rail and wheel pair roll surface, light signals automatic detection from

  12. Technical and governance considerations for advanced metering infrastructure/smart meters: Technology, security, uncertainty, costs, benefits, and risks

    International Nuclear Information System (INIS)

    McHenry, Mark P.

    2013-01-01

    The fundamental role of policymakers when considering Advanced Metering Infrastructure (AMI), or ‘smart meters for energy and water infrastructure is to investigate a broad range of complex interrelated issues. These include alternative technical and non-technical options and deployment needs, the cost and benefits of the infrastructure (risks and mitigation measures), and the impact of a number of stakeholders: consumers, distributors, retailers, competitive market operators, competing technology companies, etc. The scale and number of potential variables in the AMI space is an almost unprecedented challenge to policymakers, with the anticipation of new ancillary products and services, associated market contestability, related regulatory and policy amendments, and the adequacy of consumer protection, education, and safety considerations requiring utmost due-diligence. Embarking on AMI investment entails significant technical, implementation, and strategic risk for governments and administering bodies, and an active effort is required to ensure AMI governance and planning maximises the potential benefits, and minimise uncertainties, costs, and risks to stakeholders. This work seeks to clarify AMI fundamentals and discusses the technical and related governance considerations from a dispassionate perspective, yet acknowledges many stakeholders tend to dichotomise debate, and obfuscate both advantages and benefits, and the converse. - Highlights: • AMI presents an almost unprecedented technical and governance policy challenge. • AMI enables vertical integration of electricity, gas, water, IT, and telco entities • AMI investments involve major technical, implementation, and strategic decisions. • Adequacy of consumer education, safety, privacy, and protection is paramount. • Policy must maximise AMI benefits and minimise uncertainties, costs, and risks

  13. Technical Training: ELEC-2005

    CERN Multimedia

    Davide Vitè

    2005-01-01

    ELEC-2005 - Electronics in High Energy Physics: Autumn Term (November-December 2005) ELEC-2005 is a new course series on modern electronics, given by CERN physicists and engineers within the framework of the 2005 Technical Training Programme, in an extended format of the ELEC-2002 course series. This new, comprehensive course series is designed for people who are not electronics specialists, for example physicists, engineers and technicians working at or visiting the laboratory, who use or will use electronics in their present or future activities, in particular in the context of the LHC accelerator and experiments. ELEC-2005 is composed of four Terms. The Winter (Introduction to electronics in HEP), Spring (Integrated circuits and VLSI technology for physics), and Summer (System electronics for physics: Issues) Terms already took place. The Autumn Term: Electronics applications in HEP experiments (November-December, 10 lectures) is now open for online registration, and will start on November 8th with the...

  14. Socio-technical barriers to the use of energy-efficient timber drying technology in New Zealand

    International Nuclear Information System (INIS)

    Bell, Martha; Carrington, Gerry; Lawson, Rob; Stephenson, Janet

    2014-01-01

    This study of industrial energy behaviours identifies barriers to the use of energy-efficient drying technology in the New Zealand timber industry, and explores these barriers through the “energy cultures” lens. Vented kiln dryers were preferred by larger firms and heat pump kiln dryers were used by smaller firms. Although few firms could specify all their costs, we found no significant differences in the average operating costs, drying costs or commercial success of the larger and smaller firms. We found that socio-technical barriers create “energy cultures” at the level of both the firm and the sector, supporting the dominance of vented kiln dryers. The prevailing technologies, practices and norms at the sector level strongly support vented kilns, the status quo being embedded in the socio-technical context, hindering technological learning, improved energy efficiency and innovation. Influential stakeholders in the industry were thus part of, and locked into, the industry-wide energy culture, and were not in a position to effect change. We conclude that actors external to the prevailing industry energy culture need to leverage change in the industry norms, practices and/or technologies in order to reap the advantages of energy-efficient drying technology, assist its continued evolution and avoid the risks of path-dependency. - Highlights: • Firms processing timber in New Zealand use two main drying technologies. • Relatively inefficient vented dryers dominate over energy-efficient heat pumps. • Operating costs are similar but the socio-technical regime supports vented dryers. • Stasis is created by fixed energy cultures both within firms and across the sector. • Stasis hampers technical development in heat pump drying and business innovation

  15. Low cost options for tissue culture technology in developing countries. Proceedings of a technical meeting

    International Nuclear Information System (INIS)

    2004-02-01

    low cost options, and increasing plant survival after propagation, bioreactors, and outreach of material to the growers and farmers in developing countries. Bioreactors in plant propagation can produce millions of plants and may cut down the cost of plant production, which is yet not commonly used in developing countries. However, in the near future it could be well integrated into large scale commercial micropropagation in both developed and developing countries. In all cases, such options must be integrated without reducing the efficiency of plant propagation and compromising the plant quality. This TECDOC was prepared on the basis of contributions made by the participants in the Technical Meeting on Low Cost Tissue Culture Technology for Developing Countries, Vienna, 26-30 August 2002. This publication should be of great value to plant propagators, managers of tissue culture laboratories, scientists, organizations contemplating the establishment of new laboratories, and ongoing commercial concerns, all of whom may wish to incorporate low cost options into their day-to-day operations. Also, it would greatly serve plant propagation enterprises in developing countries with scarce funds and poor infrastructure for sustainable food production. Many of the options described can also be integrated in tissue culture laboratories that use mutation induction to develop new mutant varieties of both vegetatively and seed propagated plants, and for rapid release of the selected mutants

  16. Low cost options for tissue culture technology in developing countries. Proceedings of a technical meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2004-02-01

    low cost options, and increasing plant survival after propagation, bioreactors, and outreach of material to the growers and farmers in developing countries. Bioreactors in plant propagation can produce millions of plants and may cut down the cost of plant production, which is yet not commonly used in developing countries. However, in the near future it could be well integrated into large scale commercial micropropagation in both developed and developing countries. In all cases, such options must be integrated without reducing the efficiency of plant propagation and compromising the plant quality. This TECDOC was prepared on the basis of contributions made by the participants in the Technical Meeting on Low Cost Tissue Culture Technology for Developing Countries, Vienna, 26-30 August 2002. This publication should be of great value to plant propagators, managers of tissue culture laboratories, scientists, organizations contemplating the establishment of new laboratories, and ongoing commercial concerns, all of whom may wish to incorporate low cost options into their day-to-day operations. Also, it would greatly serve plant propagation enterprises in developing countries with scarce funds and poor infrastructure for sustainable food production. Many of the options described can also be integrated in tissue culture laboratories that use mutation induction to develop new mutant varieties of both vegetatively and seed propagated plants, and for rapid release of the selected mutants.

  17. Electron stimulated desorption of gases at technological surfaces of aluminium

    International Nuclear Information System (INIS)

    Ding, M.Q.; Williams, E.M.

    1989-01-01

    The release of gas by electron bombardment at aluminium alloy surfaces in vacuum -9 torr has been investigated for a range of treatments including bakeout and glow discharge cleaning. Particular attention has been given to the role of continuous electron bombardment, with current densities and electron energies of up to 1.5 mA cm -2 and 2.0 keV, respectively, over the 10 cm 2 of surface area under irradiation. The observations of desorption efficiency, defined as the number of desorbed molecules per incident electron, conform to a model involving a dynamic balance between adsorption and desorption, with contributions to adsorption from both surface and sub-surface gas. Continuous electron bombardment promotes a surface with low desorption efficiency, -5 mol/electron, however, the conditioning cycle is accelerated significantly by glow discharge treatment. There is evidence of some short-term memory when the samples are exposed to air. (author)

  18. 76 FR 21043 - Notice of Public Meeting: Technical Aspects of Mandatory Deposit of Published Electronic Works...

    Science.gov (United States)

    2011-04-14

    ... mandatory deposit requirements of the copyright law. The objective is to identify file submission, packaging... mandatory deposit provisions of the copyright law. Under the interim regulation, certain works available... LIBRARY OF CONGRESS Copyright Office [Docket No. 2011-3] Notice of Public Meeting: Technical...

  19. Gas-cooled reactor technology safety and siting. Report of a technical committee meeting. Working material

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-07-01

    At the invitation of the Government of the Union of Soviet Socialist Republics, the Eleventh International Conference on the HTGR and the IAEA Technical Committee Meeting on Gas-Cooled Reactor Technology, Safety and Siting were held in Dimitrovgrad, USSR, on June 21-23, 1989. The Technical Committee Meeting provided the Soviet delegates with an opportunity to display the breadth of their program on HTGRs to an international audience. Nearly one-half of the papers were presented by Soviet participants. Among the highlights of the meeting were the following: the diverse nature and large magnitude of the Soviet research and development program on high temperature gas-cooled reactors; the Government approval of the budget for the construction of the 30 MWt High Temperature Test Reactor (HTTR) in Japan (The schedule contemplates a start of construction in spring 1990 on a site at the Oarai Research Establishment and about a five year construction period.); disappointment in the announced plans to shutdown both the Fort St. Vrain (FSV) plant in the United States (US) and the Thorium High Temperature Reactor (THTR-300) in Germany (These two reactors presently represent the only operating HTGRs in the world since the AVR plant in Juelich, Germany, was also shutdown at the end of 1988.); the continuing negotiations between Germany and the USSR on the terms of the co-operation between the two countries for the construction of a HTR Module supplemented by joint research and development activities aimed at increasing coolant outlet temperatures from 750 deg. C to 950 deg. C; the continued enthusiasm displayed by both the US and German representatives for the potential of the small modular designs under development in both countries and the ability for these designs to meet the stringent requirements demanded for the future expansion of nuclear power; the combining of the HTGR technology interest of ABB-Atom and Siemens in Germany into a joint enterprise, HTR GmbH, in May 1989

  20. Gas-cooled reactor technology safety and siting. Report of a technical committee meeting. Working material

    International Nuclear Information System (INIS)

    1990-01-01

    At the invitation of the Government of the Union of Soviet Socialist Republics, the Eleventh International Conference on the HTGR and the IAEA Technical Committee Meeting on Gas-Cooled Reactor Technology, Safety and Siting were held in Dimitrovgrad, USSR, on June 21-23, 1989. The Technical Committee Meeting provided the Soviet delegates with an opportunity to display the breadth of their program on HTGRs to an international audience. Nearly one-half of the papers were presented by Soviet participants. Among the highlights of the meeting were the following: the diverse nature and large magnitude of the Soviet research and development program on high temperature gas-cooled reactors; the Government approval of the budget for the construction of the 30 MWt High Temperature Test Reactor (HTTR) in Japan (The schedule contemplates a start of construction in spring 1990 on a site at the Oarai Research Establishment and about a five year construction period.); disappointment in the announced plans to shutdown both the Fort St. Vrain (FSV) plant in the United States (US) and the Thorium High Temperature Reactor (THTR-300) in Germany (These two reactors presently represent the only operating HTGRs in the world since the AVR plant in Juelich, Germany, was also shutdown at the end of 1988.); the continuing negotiations between Germany and the USSR on the terms of the co-operation between the two countries for the construction of a HTR Module supplemented by joint research and development activities aimed at increasing coolant outlet temperatures from 750 deg. C to 950 deg. C; the continued enthusiasm displayed by both the US and German representatives for the potential of the small modular designs under development in both countries and the ability for these designs to meet the stringent requirements demanded for the future expansion of nuclear power; the combining of the HTGR technology interest of ABB-Atom and Siemens in Germany into a joint enterprise, HTR GmbH, in May 1989

  1. The chirped-pulse free-electron laser: Final technical report, September 1987--October 1988

    International Nuclear Information System (INIS)

    Moore, G.T.

    1989-01-01

    This is the final report of a theoretical and numerical investigation into the operation of pulsed free-electron lasers in which the electron energy depends on the time of injection into the wiggler. Such energy ''chirping'' over each of a train of electron micropulses injected into an FEL oscillator is expected to give rise to a laser pulse inside the optical resonator with a chirped carrier frequency ω/sub s/(/tau/). 8 refs., 7 figs

  2. Maximizing Accessibility of Academic Publications: Applications of Electronic Publishing Technology

    Science.gov (United States)

    Jeffress, Laura; Lyle, Stacey D.

    2012-01-01

    Professors at higher education institutions often feel pressure to "publish or perish" in order to maintain their standing in the academic community, yet a large number of these publications languish in obscure technical journals or are presented only once at a conference or online journal. While these methods achieve the goal of…

  3. An overview of power electronic converter technology for renewable energy systems

    DEFF Research Database (Denmark)

    Chen, Zhe

    2013-01-01

    This chapter presents power electronic technology which is an enabling tool for modern wind and marine energy conversion systems. In this chapter, the main power electronic devices are described. Various power electronic converter topologies are represented, and commonly used modulation schemes...

  4. A socio-technical approach to teaching the social impacts of technological development

    DEFF Research Database (Denmark)

    Jensen, Per Langå; Broberg, Ole

    2001-01-01

    This paper describes a socio-technical approach to teach work environment in an en-gineering education as an alternative to a science-based presentation of each potential harmful factor. The socio-technical approach emphasizes that work environment must be understood in a social context and that ......This paper describes a socio-technical approach to teach work environment in an en-gineering education as an alternative to a science-based presentation of each potential harmful factor. The socio-technical approach emphasizes that work environment must be understood in a social context...

  5. Electronic Document Imaging and Optical Storage Systems for Local Governments: An Introduction. Local Government Records Technical Information Series. Number 21.

    Science.gov (United States)

    Schwartz, Stanley F.

    This publication introduces electronic document imaging systems and provides guidance for local governments in New York in deciding whether such systems should be adopted for their own records and information management purposes. It advises local governments on how to develop plans for using such technology by discussing its advantages and…

  6. International Conference on Emerging Research in Electronics, Computer Science and Technology

    CERN Document Server

    Sheshadri, Holalu; Padma, M

    2014-01-01

    PES College of Engineering is organizing an International Conference on Emerging Research in Electronics, Computer Science and Technology (ICERECT-12) in Mandya and merging the event with Golden Jubilee of the Institute. The Proceedings of the Conference presents high quality, peer reviewed articles from the field of Electronics, Computer Science and Technology. The book is a compilation of research papers from the cutting-edge technologies and it is targeted towards the scientific community actively involved in research activities.

  7. Technology of electron beam welding for Zr-4 alloy spacer grid

    International Nuclear Information System (INIS)

    Pei Qiusheng; Wu Xueyi; Yang Qishun

    1989-10-01

    The welding technology for Zr-4 alloy spacer grid by using vacuum electron beam was studied. Through a series of welding technological experiments, metallographic examinations of seam structure and detecting tests for welding defect by X-ray defectoscopy, a good welding technology was selected to meet the requirements. The experimental results indicated that the Zr-4 alloy spacer grid welded by vacuum electron beam welding is feasible

  8. Improving the Technology of Obtaining Technical Ethanol from Alternative Raw Materials

    Directory of Open Access Journals (Sweden)

    Sergіj Petrov

    2018-05-01

    Full Text Available The purpose of the article is to study the properties of fallen leaves as raw materials for the production of bioethanol; Improvement of the technology of recycling cellulosic raw materials into bioethanol in the most energy-efficient and ecological way. As a result of the study, it has been found out that the production of biofuels from renewable raw materials is characterized by features of innovative technology: the rapid growth of this sector of economy is accompanied by a significant increase in market share. The use of fallen leaves as raw material will eliminate the current conflict of interests associated with the use of food raw materials for the production of bioethanol, will prevent the withdrawal of resources from the sphere of food production. Significant positive factors in the production and use of biofuels are improvement of environmental conditions, reduction of the harmful effects of exhaust gases on the human body, reducing environmental pollution and, consequently, reducing morbidity and associated costs of medical care. The use of bioethanol as an ecobiopilot makes it possible to increase the octane number of fuel, and, accordingly, increase the efficiency of the engine. Thus, the use of bioethanol leads to a qualitative improvement of technical and economic indicators, which is also an indicator of innovation. The threat of reducing (exhausting non-renewable sources of energy is also the factor that necessitates the development and improvement of biofuel production technology. The relatively low profitability of biofuel production is due to the low yield of the target product and the high cost of pre-treatment of cellulose raw materials. The method of obtaining bioethanol from renewable non-demanded raw materials - fallen leaves - was improved. The technique allows to increase the bioethanol yield due to more effective hydrolysis of hard-hydrolysable polysaccharides. Further development of the study of the differences in

  9. High Power Electronics - Key Technology for Wind Turbines

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Ma, Ke

    2014-01-01

    reliability challenges for the future wind turbines are explained. It is concluded that the wind turbine behavior/performance can be significantly improved by introducing power electronics, and there will be higher requirements for the power electronics performances in wind power application....

  10. Integration of electronic nose technology with spirometry: validation of a new approach for exhaled breath analysis

    NARCIS (Netherlands)

    de Vries, R.; Brinkman, P.; van der Schee, M. P.; Fens, N.; Dijkers, E.; Bootsma, S. K.; de Jongh, F. H. C.; Sterk, P. J.

    2015-01-01

    New 'omics'-technologies have the potential to better define airway disease in terms of pathophysiological and clinical phenotyping. The integration of electronic nose (eNose) technology with existing diagnostic tests, such as routine spirometry, can bring this technology to 'point-of-care'. We

  11. Justification of Technical System Control in Developing and Testing Objects of Missile and Space Technology

    Directory of Open Access Journals (Sweden)

    A. A. Fedorovskiy

    2015-01-01

    Full Text Available Tests in general lifecycle of missile and space technology, play a special role. The high cost of such products and a little time for creation and refinement, allow only a limited number of tests. Justification of the appropriate number of tests and finding the ways to reduce it are important from the practical point of view.When the appropriate number of field tests is impossible to implement, as well as if full or partial realization of the sample operation conditions is impossible the authors propose to use software with the involvement of previously obtained aprioristic information to have the modeling results of the functioning sample or its parts, according to the reliability and quality standards.Involvement of statistical methods for systems and objects of the missile and space equipment is limited to the single number of the carried-out tests. Currently used models and methods for systems of missile and barreled weapon do not allow us to conduct analysis and provide guidance on emerging issues of concern to ensure the quality and reliability of objects of the missile and space equipment by results of tests.The method of probabilistic and statistical analysis of the stochastic system operability is supposed to be used to solve a problem of the planning tests, assessment and control of reliability of technical systems at tests using aprioristic calculated and experimental information. This method makes it possible to relate the number of tests, required to prove the desirable level of reliability, to different types of constructional, functional, structural reserves of the system, as well as the level of information-and-measuring base and the completeness of available information.Thus, the structure of controlled elements, their importance, and acceptance conditions including elaboration of actions and recommendations to eliminate discrepancies in controlled parameters and improve quality of the considered system are justified and formed

  12. Adhesives technology for electronic applications materials, processing, reliability

    CERN Document Server

    Licari, James J

    2011-01-01

    Adhesives are widely used in the manufacture and assembly of electronic circuits and products. Generally, electronics design engineers and manufacturing engineers are not well versed in adhesives, while adhesion chemists have a limited knowledge of electronics. This book bridges these knowledge gaps and is useful to both groups. The book includes chapters covering types of adhesive, the chemistry on which they are based, and their properties, applications, processes, specifications, and reliability. Coverage of toxicity, environmental impacts and the regulatory framework make this book par

  13. Handbook of polymer coatings for electronics chemistry, technology and applications

    CERN Document Server

    Licari, James J

    1990-01-01

    This completely revised edition remains the only comprehensive treatise on polymer coatings for electronics. Since the original edition, the applications of coatings for the environmental protection of electronic systems have greatly increased, largely driven by the competitive need to reduce costs, weight and volume. The demands for high-speed circuits for the rapid processing of signals and data, high-density circuits for the storage and retrieval of megabits of memory, and the improved reliability required of electronics for guiding and controlling weapons and space vehicles have triggered

  14. Technical and Economical study of New Technologies and Reusable Space Vehicles promoting Space Tourism.

    Science.gov (United States)

    Srivastav, Deepanshu; Malhotra, Sahil

    2012-07-01

    For many of us space tourism is an extremely fascinating and attractive idea. But in order for these to start we need vehicles that will take us to orbit and bring us back. Current space vehicles clearly cannot. Only the Space Shuttle survives past one use, and that's only if we ignore the various parts that fall off on the way up. So we need reusable launch vehicles. Launch of these vehicles to orbit requires accelerating to Mach 26, and therefore it uses a lot of propellant - about 10 tons per passenger. But there is no technical reason why reusable launch vehicles couldn't come to be operated routinely, just like aircraft. The main problem about space is how much it costs to get there, it's too expensive. And that's mainly because launch vehicles are expendable - either entirely, like satellite launchers, or partly, like the space shuttle. The trouble is that these will not only reduce the cost of launch - they'll also put the makers out of business, unless there's more to launch than just a few satellites a year, as there are today. Fortunately there's a market that will generate far more launch business than satellites ever well - passenger travel. This paper assesses this emerging market as well as technology that will make space tourism feasible. The main conclusion is that space vehicles can reduce the cost of human transport to orbit sufficiently for large new commercial markets to develop. Combining the reusability of space vehicles with the high traffic levels of space tourism offers the prospect of a thousandfold reduction in the cost per seat to orbit. The result will be airline operations to orbit involving dozens of space vehicles, each capable of more than one flight per day. These low costs will make possible a rapid expansion of space science and exploration. Luckily research aimed at developing low-cost reusable launch vehicles has increased recently. Already there are various projects like Spaceshipone, Spaceshiptwo, Spacebus, X-33 NASA etc. The

  15. Study of technical and economical feasibility for implementation of a movable unit for treatment of industrial effluents with electron beam

    International Nuclear Information System (INIS)

    Rela, Carolina Sciamarelli

    2006-01-01

    The treatment of industrial effluents is a practice that is disseminating in accelerated rhythm, of contributing to reinforce the public image, through the combat of the pollution, it brings economical advantages allowing the companies the reuse of the treated water in their own processes. The liquid effluent treatment technique studied in the present work is the one that uses the chemical oxidation/reduction standing out the use of the electron beam (e.b.) radiation. This technique uses an advanced oxidation process, generating radicals highly reagents that provoke the oxidation, reduction, dissociation and degradation in composed organic and exercising lethal effect in general in the microorganisms and parasites. In this work a conceptual and basic project of a movable unit of effluents treatment using electron beam radiation process was developed, in order that the unit moves until the treatment point, where the effluent is produced, facilitating the logistics. A technical and economical feasibility study was also elaborated allowing data on the capacity and cost of effluents processing to consolidate the values of the necessary investments to be presented to foundations organs for the construction of a movable unit. The results of the studies demonstrated that it is technically viable attending the pertinent legislation of Brazil, in the aspects of Radiation Protection and transport limit capacity. The unitary cost of the e.b. radiation processing in the movable unit was shown more expensive than in the fixed unit, the reason is the decrease of the efficiency of the interaction of the incident electrons in the effluent, due to the reduction of electron energy operation time of the unit. (author)

  16. Technology transfer present and futures in the electronic arts

    Directory of Open Access Journals (Sweden)

    Brian Degger

    2008-01-01

    Full Text Available We are entering an era where creating the fantastical is possible in the arts. In the areas of mixed reality and biological arts, responsive works are created based on advances in basic science and technology. This is enabling scientists and artists to pose new questions. As the time between discovery and application is so short, artists need imaginative ways of accessing new technology in order to critique and use it.These are the new paints that the majority of artists cannot afford or access, technology to enable cloning of DNA, to print channels on a chip, to access proprietary 3G networks. Currently, partnerships or residencies are used to facilitate artist’s access to these technologies. What would they do if technology was available that enabled them to make any art work they so desire? Are the limitations in current technology an advantage rather than a disadvantage in some of their works? Does interaction with technologists make their work more robust? Are there disadvantages? How do they get access to the technology they require? Open source or proprietary? Or have they encountered the situation where their vision is greater than technology allows. When their work breaks because of this fact, is their art broken? Blast Theory (Brighton,UK, FoAM(Brussels, Belgium and Amsterdam, Netherlands, SymbioticA (Perth, Australia are organisations pushing technological boundaries in the service of art. This paper addresses some questions of technology transfer in relation to recent artworks, particularly I like Frank in Adelaide (Blast Theory, transient reality generators (trg (FoAM and Multi electrode array artist (MeART (SymbioticA.

  17. Fundamental Technical Elements of Freeze-fracture/Freeze-etch in Biological Electron Microscopy

    Science.gov (United States)

    Freeze-fracture/freeze-etch describes a process whereby specimens, typically biological or nanomaterial in nature, are frozen, fractured, and replicated to generate a carbon/platinum "cast" intended for examination by transmission electron microscopy. Specimens are subjected to u...

  18. Technical development of industry for 30 years

    International Nuclear Information System (INIS)

    2009-01-01

    This book mentions the history for 30 years since 1979 on industrial technology, which records change of system and environment of industrial technology development, like economical and social environment, industrial technology policy, support system on technical development and enterprise institute, assignment for future and product of industrial technology by field such as electric electronic, information and communications, machine material and fiber chemistry, and the way which Korea industrial technology association walked on.

  19. Innovating the Standard Procurement System Through Electronic Commerce Technologies

    National Research Council Canada - National Science Library

    Mangum, Stephen

    1999-01-01

    ... business processes with commercial best practices and advances in electronic commerce. When fully implemented, it will serve more than 1,100 sites worldwide and be employed by over 44,000 professionals...

  20. Power System Electronics (PSE) Development for SmallSat Technology

    Data.gov (United States)

    National Aeronautics and Space Administration — We develop a modular Power System Electronics (PSE) that is reliable, efficient, and flexible to meet the Goddard Modular Smallsat Architecture (GMSA) challenge....

  1. Electron-ionic technology of storage of foodstuffs

    International Nuclear Information System (INIS)

    Tsoj, A.P.

    1996-01-01

    Work is trained on reduction of food suffer losses under cold store due to its drying and spoiling. Experimental cold store of fruits in 'microclimates' in electron-ionic medium created with help of pilot unit is carried out

  2. The development of technology for recycling of electronic scrap

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hyo-Shin; Kim, Won-Baek; Sohn, Yong-Uhn [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    Electronic devices, especially computer becomes an essential tools for home and industries entering the information era. The number of computers exceed over 100 million, hence, the amount of end of life(EOL) computer and electronic scrap is increasing. These wastes and scraps include products rejected from manufacturing processes and obstacle computers. Owing to a short life cycle of electronic products and rapid growth of electronic industries, the number of domestic EOL computers goes beyond a million and its disposal causes an environmental problems. Therefore, this recycling is considered to play an important role from the viewpoint of environmental preservation as well as reusable resources. The process development for the recovery of valuable materials and minimization of waste from electronic scrap has been carried out. In the first year of three year project, physical separation such as shredding, crushing, and magnetic separation is established to reclaim valuable materials effectively. Then, hydro- and pyrometallurgical processes are employed to recover valuable metals from electronic scrap. First, metallic and nonmetallic portion are separated from PCBs by a newly designed shredder to prevent hazardous organic materials from further chemical treatment. The optimum conditions for each unit process were found in terms of separation ratio, energy consumption, recovery rate, etc. (author). 92 refs., 24 tabs., 39 figs.

  3. INFLUENCE OF ORGANIZATIONAL AND TECHNOLOGICAL SOLUTIONS TO TECHNICAL AND ECONOMICAL INDICATORS IN PROJECT OF HEAT INSULATION FACADES

    Directory of Open Access Journals (Sweden)

    BABIJ I. N. Cand. Sc. (Tech., Associate Professor,

    2016-09-01

    Full Text Available Summary. Raising of problem. The article dedicated to the solution important problems of choosing rational technical and economic indicators of the duration and cost the process heat insulation facades of buildings by means of experimental and statistical modeling organizational and technological solutions. For this we used the results of numerical experiment, theory a shorthand experiment planning and contemporary computer programs. Purpose. We used experimentally-statistical modeling to establish the impact of organizational and technological solutions for heat insulation of facades by hinged ventilated systems on technical and economic parameters of the project, such as duration and cost. Conclusion. We investigated depending duration assembly jobs and manufacturing cost on the value and combination of variable factors experimental and statistical modeling of construction processes and results patterns of change in studied parameters.

  4. New Possibilities of Power Electronic Structures Using SiC Technology

    Directory of Open Access Journals (Sweden)

    Robert Sul

    2006-01-01

    Full Text Available This paper is dedicated to the recent unprecedented boom of SiC electronic technology. The contribution deals with brief survey of those properties. In particular, the differences (both good and bad between SiC electronics technology and well-known silicon VLSI technology are highlighted. Projected performance benefits of SiC electronics are given for several large-scale applications on the end of the contribution. The basic properties of SiC material have been discussed already on the beginning of 80’s, also at our university.

  5. Notes for a pedagogical approach to skills training for entrepreneurship in technical and technological institutes of Ecuador

    OpenAIRE

    Rosa Roxana Chiquito-Chilán; Blanca Cortón-Romero

    2016-01-01

    The enterprise value has increased with the passage of time; and today has special significance especially in countries as in the case of Ecuador; where efforts to changing the productive matrix, a process that involves a productive revolution through the development of knowledge and human talent develop. The achievement of the purposes of this strategy depends largely on the quality of the formation of enterprising professionals. A technical and technological institutes are in business techn...

  6. Translating English Technical Texts The Role of the Translator and the Challenges of Technological Facilities

    Directory of Open Access Journals (Sweden)

    Dana Rus

    2009-12-01

    Full Text Available The paper approaches the specific case of the technical discourse in the context of a modern world which facilitates and promotes a more and more refined diversification of specialized texts. Created, imposed, promoted and sustained by economic reasons, the translation of technical texts finds new challenges as it is confronted with the opportunities offered by the cyberspace. While being quick, available and free, online instant translation services prove to be essentially inappropriate for the translation of technical texts, where accuracy is a prerogative.

  7. Proceedings of 8. national conference on nuclear electronic and nuclear detection technology: Pt.1

    International Nuclear Information System (INIS)

    1996-01-01

    The 8th National Conference on Nuclear Electronics and Nuclear Detection Technology was held during 2-7, 12, 1996 in Zhuhai, Guangdong, China. 184 pieces of papers were collected in the conference proceedings. The contents of the conference proceedings are: nuclear electronics, nuclear detectors, nuclear instruments and its application, nuclear medical electronics, computer applications in nuclear sciences and technology, measurement of nuclear monitoring and nuclear explosion, radiation hardened electronics, liquid scintillation counting techniques and miscellaneous. Reported hereafter is the first part of the proceedings

  8. Impact of Digital Tooth Preparation Evaluation Technology on Preclinical Dental Students' Technical and Self-Evaluation Skills.

    Science.gov (United States)

    Gratton, David G; Kwon, So Ran; Blanchette, Derek; Aquilino, Steven A

    2016-01-01

    The aim of this study was to evaluate the effect of digital tooth preparation imaging and evaluation technology on dental students' technical abilities, self-evaluation skills, and the assessment of their simulated clinical work. A total of 80 second-year students at one U.S. dental school were assigned to one of three groups: control (n=40), E4D Compare (n=20), and Sirona prepCheck (n=20). Students in the control group were taught by traditional teaching methodologies, and the technology-assisted groups received both traditional training and supplementary feedback from the corresponding digital system. Three outcomes were measured: faculty technical score, self-evaluation score, and E4D Compare scores at 0.30 mm tolerance. Correlations were determined between the groups' scores from visual assessment and self-evaluation and between the visual assessment and digital scores. The results showed that the visual assessment and self-evaluation scores did not differ among groups (p>0.05). Overall, correlations between visual and digital assessment scores were modest though statistically significant (5% level of significance). These results suggest that the use of digital tooth preparation evaluation technology did not impact the students' prosthodontic technical and self-evaluation skills. Visual scores given by faculty and digital assessment scores correlated moderately in only two instances.

  9. RESEARCH OF INFLUENCE OF QUALITY OF ELECTRONIC EDUCATIONAL RESOURCES ON QUALITY OF TRAINING WITH USE OF DISTANCE TECHNOLOGIES

    Directory of Open Access Journals (Sweden)

    H. M. Kravtsov

    2013-03-01

    Full Text Available Communication improving of educational processes requires today new approaches to the management arrangements and forming of educational policy in the field of distance learning, which is based on the use of modern information and communication technologies. An important step in this process is the continuous monitoring of the development and implementation of information technology and, in particular, the distance learning systems in higher educational establishments. The main objective of the monitoring is the impact assessment on the development of distance learning following the state educational standards, curricula, methodical and technical equipment and other factors; factors revelation that influence the implementation and outcomes of distance learning; results comparison of educational institution functioning and distance education systems in order to determine the most efficient ways of its development. The paper presents the analysis results of the dependence of the quality of educational services on the electronic educational resources. Trends in educational services development was studied by comparing the quality influence of electronic educational resources on the quality of educational services of higher pedagogical educational institutions of Ukraine as of 2009-2010 and 2012-2013. Generally, the analysis of the survey results allows evaluating quality of the modern education services as satisfactory and it can be said that almost 70% of the success of their future development depends on the quality of the used electronic educational resources and distance learning systems in particular.

  10. Basic radiation effects in nuclear power electronics technology

    International Nuclear Information System (INIS)

    Gover, J.E.; Srour, J.R.

    1985-05-01

    An overview is presented of the effects of radiation in microelectronics technology. The approach taken throughout these notes is to review microscopic phenomena associated with radiation effects and to show how these lead to macroscopic effects in semiconductor devices and integrated circuits. Bipolar integrated circuits technology is reviewed in Appendix A. Appendix B gives present and future applications of radiation-tolerant microelectronics in nuclear power applications as well as the radiation tolerance requirements of these applications

  11. Smart E-Beam for Defect Identification & Analysis in the Nanoscale Technology Nodes: Technical Perspectives

    Directory of Open Access Journals (Sweden)

    Ankush Oberai

    2017-10-01

    Full Text Available Optical beam has been the veteran inspector of semiconductor wafer production house, ever since the birth of integrated circuit (IC. As technology and market place raise the bar on chip density, Moore’s law stretches to the limit. Due to its inherent physical limitations, the optical method just cannot see the measuring rod of silicon industry getting recalibrated to finer nano-scales. Electron Beam Inspection (EBI, by virtue of its high resolution, has started to rule the nodes at 10 nm and below. As the geometries shrink, defects can reside deep within the structures. EBI can find those tiny defects, which otherwise go scot-free with optical tools. However, EBI suffers the handicap of poor performance and low throughput. It is therefore essential to complement EBI by judiciously crafting out the methods for getting the desired performance, a subject matter to which, this article is committed to. The research torchlights the critical EBI throughput problem to round-up “care-areas”. Such guided and focused inspection augments throughput, thereby positioning EBI as the industrial grade candidate in finer nanometer segment. Besides gearing up to current trends, the smart EBI school of thought is inspirational, to fuel the aspirations for 1 nanometer scale.

  12. [Application of electronic fence technology based on GIS in Oncomelania hupensis snail monitoring].

    Science.gov (United States)

    Zhi-Hua, Chen; Yi-Sheng, Zhu; Zhi-Qiang, Xue; Xue-Bing, Li; Yi-Min, Ding; Li-Jun, Bi; Kai-Min, Gao; You, Zhang

    2017-07-27

    To study the application of Geographic Information System (GIS) electronic fence technique in Oncomelania hupensis snail monitoring. The electronic fence was set around the history and existing snail environments in the electronic map, the information about snail monitoring and controlling was linked to the electronic fence, and the snail monitoring information system was established on these bases. The monitoring information was input through the computer and smart phone. The electronic fence around the history and existing snail environments was set in the electronic map (Baidu map), and the snail monitoring information system and smart phone APP were established. The monitoring information was input and upload real-time, and the snail monitoring information was demonstrated in real time on Baidu map. By using the electronic fence technology based on GIS, the unique "environment electronic archives" for each snail monitoring environment can be established in the electronic map, and real-time, dynamic monitoring and visual management can be realized.

  13. Integration of electronic nose technology with spirometry: validation of a new approach for exhaled breath analysis.

    Science.gov (United States)

    de Vries, R; Brinkman, P; van der Schee, M P; Fens, N; Dijkers, E; Bootsma, S K; de Jongh, F H C; Sterk, P J

    2015-10-15

    New 'omics'-technologies have the potential to better define airway disease in terms of pathophysiological and clinical phenotyping. The integration of electronic nose (eNose) technology with existing diagnostic tests, such as routine spirometry, can bring this technology to 'point-of-care'. We aimed to determine and optimize the technical performance and diagnostic accuracy of exhaled breath analysis linked to routine spirometry. Exhaled breath was collected in triplicate in healthy subjects by an eNose (SpiroNose) based on five identical metal oxide semiconductor sensor arrays (three arrays monitoring exhaled breath and two reference arrays monitoring ambient air) at the rear end of a pneumotachograph. First, the influence of flow, volume, humidity, temperature, environment, etc, was assessed. Secondly, a two-centre case-control study was performed using diagnostic and monitoring visits in day-to-day clinical care in patients with a (differential) diagnosis of asthma, chronic obstructive pulmonary disease (COPD) or lung cancer. Breathprint analysis involved signal processing, environment correction based on alveolar gradients and statistics based on principal component (PC) analysis, followed by discriminant analysis (Matlab2014/SPSS20). Expiratory flow showed a significant linear correlation with raw sensor deflections (R(2)  =  0.84) in 60 healthy subjects (age 43  ±  11 years). No correlation was found between sensor readings and exhaled volume, humidity and temperature. Exhaled data after environment correction were highly reproducible for each sensor array (Cohen's Kappa 0.81-0.94). Thirty-seven asthmatics (41  ±  14.2 years), 31 COPD patients (66  ±  8.4 years), 31 lung cancer patients (63  ±  10.8 years) and 45 healthy controls (41  ±  12.5 years) entered the cross-sectional study. SpiroNose could adequately distinguish between controls, asthma, COPD and lung cancer patients with cross-validation values

  14. Influence of non-technical policies on choices of waste solidification technologies

    International Nuclear Information System (INIS)

    Trubatch, S.L.

    1987-01-01

    This paper describes and discusses non-technical policy considerations which may improperly influence decisions on the solidification of low-level radioactive wastes (''LLW''). These policy considerations are contained principally in several State and Federal statutes which regulate various aspects of LLW disposal. One policy consideration in particular, the unqualified bias in favor of volume reduction, is shown to present a substantial potential for leading to technically suboptimal decisions on the appropriate processes for solidifying LLW. To avoid the unintended skewing of technical decisions by non-technical policy considerations, certain current policies may need to be revised to ensure that the choices of waste treatment, including decisions on solidification, are based primarily on reasonable assurance of adequate protection of public health and safety. This goal may be realized in part by basing any disposal fee structure on more than just LLW volume to include consideration of the waste's activity and its difficulty of confinement

  15. New Approaches for Navy Technical Training and Job Performance Aiding Using Expanded IETM Technology

    National Research Council Canada - National Science Library

    Jorgensen, Eric L; Fuller, Joseph J

    1996-01-01

    ...) began to develop better ways to present Technical Information (TI) to Navy Fleet users needed for purposes of operating, maintaining, training, and logistically supporting the Navy's inventory of weapon systems...

  16. Using case studies to teach an engineering technology technical writing class

    Science.gov (United States)

    Green, M. M.

    1981-01-01

    The use of the case method in teaching various technical communication skills is described. Features of the method considered include: solving communication problems, identifying an audience, planning written communications, presenting written communications, and using visual aids.

  17. Technical and scientific production of the Brazilian Nuclear Technology Development Center in the year 1993

    International Nuclear Information System (INIS)

    Sousa, M.G.

    1994-01-01

    This paper presents a list of the technical and scientific documents produced by CDTN during 1993. These documents are available through the library, with exception of those remarked with asterisks, due to restrictions imposed by contractual bounds. (author)

  18. Electronic commerce: wiring the coal industry for new data technology

    Energy Technology Data Exchange (ETDEWEB)

    Carter, R.A.

    1998-07-01

    Industry pundits predict that coal by wire may some day replace much of the industry`s long-distance shipping requirements and their attendant costs, but data by wire, also known as electronic commerce (EC) can today offer coal producers and customers the means to gather and send large volumes of data cheaply and quickly. EC`s major components - electronic data interchange (EDI), bar-coding, smart codes, radio frequency `D`, and the internet - can reduce costs in equipment-intensive industries such as mining. The US National Mining Association sponsored a forum to discuss these alternatives at its 1998 Electronic Commerce Summit held in Tuscon, Arizona, 18-20 May. A report is given of discussions at the forum and contacts are given for sources of EDI information.

  19. Main trends in FSC member organisations' use of electronic communications technologies: responses to the questionnaire

    International Nuclear Information System (INIS)

    Aebersold, M.

    2006-01-01

    The questionnaire about the experience with electronic, web tools for communicating on radioactive waste management (RWM) was sent to a number of RWM organisations and 5 contributions were received and analysed. All responding organisations indicate that ideas and plans involving electronic media are in constant active development. In each organisation there is usually a small, specialised team to run the web, often in close cooperation with the media department of the Organisation and technical units, but the technical implementation of electronic tools may be out-sourced. On the whole, the use of web systems is seen as very efficient, as an instrument for passing information and maintaining a link with active stakeholders, but less appropriate to create the confidence you can develop in a person to person communication

  20. Electronic aroma detection technology for forensic and law enforcement applications

    Energy Technology Data Exchange (ETDEWEB)

    Barshick, S.-A.; Griest, W.H.; Vass, A.A.

    1996-12-31

    A major problem hindering criminal investigations is the lack of appropriate tools for proper crime scene investigations. Often locating important pieces of evidence means relying on the ability of trained detection canines. Development of analytical technology to uncover and analyze evidence, potentially at the scene, could serve to expedite criminal investigations, searches, and court proceedings. To address this problem, a new technology based on gas sensor arrays was investigated for its applicability to forensic and law enforcement problems. The technology employs an array of sensors that respond to volatile chemical components yielding a characteristic `fingerprint` pattern representative of the vapor- phase composition of a sample. Sample aromas can be analyzed and identified using artificial neural networks that are trained on known aroma patterns. Several candidate applications based on known technological needs of the forensic and law enforcement communities have been investigated. These applications have included the detection of aromas emanating from cadavers to aid in determining time since death, drug detection for deterring the manufacture, sale, and use of drugs of abuse, and the analysis of fire debris for accelerant identification. The results to date for these applications have been extremely promising and demonstrate the potential applicability of this technology for forensic use.

  1. Chromium Waste Treatment from Leather Manufacture Using Electron Beam Radiation Technic

    International Nuclear Information System (INIS)

    Didiek Herhady, R.; Sukarsono, R.

    2007-01-01

    Leather manufacture chromium waste treatment using chemical methods have an essential disadvantage, because of the production of the secondary contamination of wastes and separated sediments used by reagents. Therefore, a new technique is needed to solve this problem. The aim of the research to learn the advantages of electron beam radiation for chromium waste treatment. Water radiolysis can be produced by the interaction between electron beam and water or liquid substances. This phenomenon produces many reducing agents and ions that could reduce chromium concentrations in the liquid waste. Ethyl alcohol as a scavenger was added in the waste samples, then the pH of varied from 1, 4, 8 to 12, then were irradiated. Irradiation were done by Electron Beam Machine with dose 15, 25, and 35 kGy. After irradiation, chromium concentration in the samples were analyzed by AAS and UV-vis spectrophotometer. The results had shown that chromium could be reduced by high dose electron beam. The optimum reduction of chromium was achieved at liquid waste pH 8 and irradiation dose 35 kGy. (author)

  2. Technical Limitations of Electronic Health Records in Community Health Centers: Implications on Ambulatory Care Quality

    Science.gov (United States)

    West, Christopher E.

    2010-01-01

    Research objectives: This dissertation examines the state of development of each of the eight core electronic health record (EHR) functionalities as described by the IOM and describes how the current state of these functionalities limit quality improvement efforts in ambulatory care settings. There is a great deal of literature describing both the…

  3. Absolute experimental cross sections for the electron impact ionization of rubidium. Technical summary report

    International Nuclear Information System (INIS)

    Hughes, D.W.; Feeney, R.K.

    1980-01-01

    The absolute cross sections for the double, triple, and quadruple ionization of Rb + ions by electron impact have been measured from below their respective thresholds to approximately 3000 eV. This determination has been accomplished using a crossed beam facility in which monoenergetic beams of ions and electrons are caused to intersect at right angles in a well-defined collision volume. Multiply charged, product ions born as a result of the electron impact are deflected into their respective detectors by cascaded electrostatic analyzers. The multiply charged beam current component is measured by means of a vibrating reed electrometer operating in the rate-of-charge mode. The required singly charged rubidium ions are produced in a thermionic ion source and pass through a series of focusing, collimating and deflecting structures before entering the interaction region. A thermionically generated, rectangular electron beam intercepts the target ions in a spatially designated collision volume. Just prior to entering this interaction region the two beams can be made to pass through a movable slit scanner which determines their spatial profiles. The various charged particle currents, energies and beam current density distributions represent the experimental data from which the desired absolute cross sections have been determined. The results obtained with this technique are compared with available theoretical predictions of the appropriate cross sections

  4. Technology of niobium and molybdenum refining by electron beam

    International Nuclear Information System (INIS)

    Conti, R.A.; Pinatti, D.G.; Sandim, H.R.Z.

    1988-01-01

    The uses of metals and alloys in superconductors (Nb46%Ti), aerospatial industry (Ti6Al4V), electroeletronic industry (Nb, Mo, W) and in surgical implants (Ti, Nb) are increasing nowadays. A refining process of niobium and molybdenum by electron beam technique, since the oxides reduction till the obtention of a high purity ingot is presented. (C.G.C.) [pt

  5. Research on electron beam welding technology of steel HR-4

    International Nuclear Information System (INIS)

    Guo Peng; Guan Kai

    2001-01-01

    The electron beam weldability of HR- 4 steels (J75 and J90) is studied and the welding parameters needed for design and usage are presented. The assessment on the effect of mechanical properties by different processing order of welding and heat-treatment is made

  6. Simulation Tools for Power Electronics Courses Based on Java Technologies

    Science.gov (United States)

    Canesin, Carlos A.; Goncalves, Flavio A. S.; Sampaio, Leonardo P.

    2010-01-01

    This paper presents interactive power electronics educational tools. These interactive tools make use of the benefits of Java language to provide a dynamic and interactive approach to simulating steady-state ideal rectifiers (uncontrolled and controlled; single-phase and three-phase). Additionally, this paper discusses the development and use of…

  7. Size Control Technology of Silver Nanoparticles Using Electron Beam Irradiation

    International Nuclear Information System (INIS)

    Kang, Hyun Suk; Kim, Byungnam; Kim, Hye Won; Koo, Yong Hwan; Lee, Byung Cheol; Park, Ji Hyun; Bae, Hyung Bin; Park, Changmoon

    2013-01-01

    The manufacturing of silver nanoparticles using an electron beam is easy, fast, and highly productive, and it is possible at room temperature with no chemical residuals. Its various advantages therefore make this an important method for manufacturing nanoparticles such as silver, copper, and platinum. In particular, despite the use of electron beam irradiation, the results show that this method makes it possible to produce silver nanoparticles at low cost since low beam energy and low doses are used. This means that middle and high-energy electron beam accelerators are very expensive, but a low-energy electron beam accelerator has a relatively low cost of around 4-5 times, and mass production for a flow reaction without the need for extra radiation shielding is possible. Silver nanoparticles are of great interest to many researchers owing to their ability to be used in many applications such as catalysis, nanoelectronics, optical filters, electromagnetic interference shielding, surface Raman scattering, medical supplies, fabrics, cosmetics, hygiene and kitchen supplies, and electric home appliances

  8. Agent Technologies in the Electronic Classroom: Some Pedagogical Issues.

    Science.gov (United States)

    Dowling, Carolyn

    The use of intelligent software agents within computer mediated learning environments has become an important focus of research and development in both AI and educational contexts. Some of the roles envisaged and implemented for these electronic entities involve direct interactions with students, participating in the "social" dimension of the…

  9. Using XML Technologies to Organize Electronic Reference Resources

    OpenAIRE

    Huser, Vojtech; Del Fiol, Guilherme; Rocha, Roberto A.

    2005-01-01

    Provision of access to reference electronic resources to clinicians is becoming increasingly important. We have created a framework for librarians to manage access to these resources at an enterprise level, rather than at the individual hospital libraries. We describe initial project requirements, implementation details, and some preliminary results.

  10. Size Control Technology of Silver Nanoparticles Using Electron Beam Irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Hyun Suk; Kim, Byungnam; Kim, Hye Won; Koo, Yong Hwan; Lee, Byung Cheol [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Ji Hyun [Univ. of Science and Technology, Daejeon (Korea, Republic of); Bae, Hyung Bin [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Park, Changmoon [Chungnam National Univ., Daejeon (Korea, Republic of)

    2013-12-15

    The manufacturing of silver nanoparticles using an electron beam is easy, fast, and highly productive, and it is possible at room temperature with no chemical residuals. Its various advantages therefore make this an important method for manufacturing nanoparticles such as silver, copper, and platinum. In particular, despite the use of electron beam irradiation, the results show that this method makes it possible to produce silver nanoparticles at low cost since low beam energy and low doses are used. This means that middle and high-energy electron beam accelerators are very expensive, but a low-energy electron beam accelerator has a relatively low cost of around 4-5 times, and mass production for a flow reaction without the need for extra radiation shielding is possible. Silver nanoparticles are of great interest to many researchers owing to their ability to be used in many applications such as catalysis, nanoelectronics, optical filters, electromagnetic interference shielding, surface Raman scattering, medical supplies, fabrics, cosmetics, hygiene and kitchen supplies, and electric home appliances.

  11. CMOS technology: a critical enabler for free-form electronics-based killer applications

    KAUST Repository

    Hussain, Muhammad Mustafa; Hussain, Aftab M.; Hanna, Amir

    2016-01-01

    Complementary metal oxide semiconductor (CMOS) technology offers batch manufacturability by ultra-large-scaleintegration (ULSI) of high performance electronics with a performance/cost advantage and profound reliability. However, as of today

  12. New tools for an old trade: a socio-technical appraisal of how electronic decision support is used by primary care practitioners.

    Science.gov (United States)

    Peiris, David; Usherwood, Tim; Weeramanthri, Tarun; Cass, Alan; Patel, Anushka

    2011-11-01

    This article explores Australian general practitioners' (GPs) views on a novel electronic decision support (EDS) tool being developed for cardiovascular disease management. We use Timmermans and Berg's technology-in-practice approach to examine how technologies influence and are influenced by the social networks in which they are placed. In all, 21 general practitioners who piloted the tool were interviewed. The tool occupied an ill-defined middle ground in a dialectical relationship between GPs' routine care and factors promoting best practice. Drawing on Lipsky's concept of 'street-level bureaucrats', the tool's ability to process workloads expeditiously was of greatest appeal to GPs. This feature of the tool gave it the potential to alter the structure, process and content of healthcare encounters. The credibility of EDS tools appears to be mediated by fluid notions of best practice, based on an expert scrutiny of the evidence, synthesis via authoritative guidelines and dissemination through trusted and often informal networks. Balanced against this is the importance of 'soft' forms of knowledge such as intuition and timing in everyday decision-making. This resonates with Aristotle's theory of phronesis (practical wisdom) and may render EDS tools inconsequential if they merely process biomedical data. While EDS tools show promise in improving health practitioner performance, the socio-technical dimensions of their implementation warrant careful consideration. © 2011 The Authors. Sociology of Health & Illness © 2011 Foundation for the Sociology of Health & Illness/Blackwell Publishing Ltd.

  13. Light Water Reactor Sustainability Program Reactor Safety Technologies Pathway Technical Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    Corradini, M. L. [Univ. of Wisconsin, Madison, WI (United States); Peko, D. [US Dept. of Energy, Washington, DC (United States); Farmer, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Rempe, J. [Rempe and Associates LLC, Idaho Falls, ID (United States); Humrickhouse, P. [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Robb, K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gauntt, R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Osborn, D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-06-01

    In the aftermath of the March 2011 multi-unit accident at the Fukushima Daiichi nuclear power plant (Fukushima), the nuclear community has been reassessing certain safety assumptions about nuclear reactor plant design, operations and emergency actions, particularly with respect to extreme events that might occur and that are beyond each plant’s current design basis. Because of our significant domestic investment in nuclear reactor technology (99 operating reactors in the fleet of commercial LWRs with five under construction), the United States has been a major leader internationally in these activities. The U.S. nuclear industry is voluntarily pursuing a number of additional safety initiatives. The NRC continues to evaluate and, where deemed appropriate, establish new requirements for ensuring adequate protection of public health and safety in the occurrence of low probability events at nuclear plants; (e.g., mitigation strategies for beyond design basis events initiated by external events like seismic or flooding initiators). The DOE has also played a major role in the U.S. response to the Fukushima accident. Initially, DOE worked with the Japanese and the international community to help develop a more complete understanding of the Fukushima accident progression and its consequences, and to respond to various safety concerns emerging from uncertainties about the nature of and the effects from the accident. DOE R&D activities are focused on providing scientific and technical insights, data, analyses methods that ultimately support industry efforts to enhance safety. These activities are expected to further enhance the safety performance of currently operating U.S. nuclear power plants as well as better characterize the safety performance of future U.S. plants. In pursuing this area of R&D, DOE recognizes that the commercial nuclear industry is ultimately responsible for the safe operation of licensed nuclear facilities. As such, industry is considered the primary

  14. Light Water Reactor Sustainability Program: Reactor Safety Technologies Pathway Technical Program Plan

    Energy Technology Data Exchange (ETDEWEB)

    Corradini, M. L. [Univ. of Wisconsin, Madison, WI (United States)

    2015-06-01

    In the aftermath of the March 2011 multi-unit accident at the Fukushima Daiichi nuclear power plant (Fukushima), the nuclear community has been reassessing certain safety assumptions about nuclear reactor plant design, operations and emergency actions, particularly with respect to extreme events that might occur and that are beyond each plant’s current design basis. Because of our significant domestic investment in nuclear reactor technology (99 operating reactors in the fleet of commercial LWRs with five under construction), the United States has been a major leader internationally in these activities. The U.S. nuclear industry is voluntarily pursuing a number of additional safety initiatives. The NRC continues to evaluate and, where deemed appropriate, establish new requirements for ensuring adequate protection of public health and safety in the occurrence of low probability events at nuclear plants; (e.g., mitigation strategies for beyond design basis events initiated by external events like seismic or flooding initiators). The DOE has also played a major role in the U.S. response to the Fukushima accident. Initially, DOE worked with the Japanese and the international community to help develop a more complete understanding of the Fukushima accident progression and its consequences, and to respond to various safety concerns emerging from uncertainties about the nature of and the effects from the accident. DOE R&D activities are focused on providing scientific and technical insights, data, analyses methods that ultimately support industry efforts to enhance safety. These activities are expected to further enhance the safety performance of currently operating U.S. nuclear power plants as well as better characterize the safety performance of future U.S. plants. In pursuing this area of R&D, DOE recognizes that the commercial nuclear industry is ultimately responsible for the safe operation of licensed nuclear facilities. As such, industry is considered the primary

  15. Designing a system for patients controlling providers' access to their electronic health records: organizational and technical challenges.

    Science.gov (United States)

    Leventhal, Jeremy C; Cummins, Jonathan A; Schwartz, Peter H; Martin, Douglas K; Tierney, William M

    2015-01-01

    Electronic health records (EHRs) are proliferating, and financial incentives encourage their use. Applying Fair Information Practice principles to EHRs necessitates balancing patients' rights to control their personal information with providers' data needs to deliver safe, high-quality care. We describe the technical and organizational challenges faced in capturing patients' preferences for patient-controlled EHR access and applying those preferences to an existing EHR. We established an online system for capturing patients' preferences for who could view their EHRs (listing all participating clinic providers individually and categorically-physicians, nurses, other staff) and what data to redact (none, all, or by specific categories of sensitive data or patient age). We then modified existing data-viewing software serving a state-wide health information exchange and a large urban health system and its primary care clinics to allow patients' preferences to guide data displays to providers. Patients could allow or restrict data displays to all clinicians and staff in a demonstration primary care clinic, categories of providers (physicians, nurses, others), or individual providers. They could also restrict access to all EHR data or any or all of five categories of sensitive data (mental and reproductive health, sexually transmitted diseases, HIV/AIDS, and substance abuse) and for specific patient ages. The EHR viewer displayed data via reports, data flowsheets, and coded and free text data displayed by Google-like searches. Unless patients recorded restrictions, by default all requested data were displayed to all providers. Data patients wanted restricted were not displayed, with no indication they were redacted. Technical barriers prevented redacting restricted information in free textnotes. The program allowed providers to hit a "Break the Glass" button to override patients' restrictions, recording the date, time, and next screen viewed. Establishing patient

  16. Electronic Mail, Privacy, and the Electronic Communications Privacy Act of 1986: Technology in Search of Law.

    Science.gov (United States)

    Samoriski, Jan H.; And Others

    1996-01-01

    Attempts to clarify the status of e-mail privacy under the Electronic Communications Privacy Act of 1986 (ECPA). Examines current law and the paucity of definitive case law. A review of cases and literature suggests there is a gap in the existing ECPA that allows for potentially abusive electronic monitoring and interception of e-mail,…

  17. Technology for the compatible integration of silicon detectors with readout electronics

    International Nuclear Information System (INIS)

    Zimmer, G.

    1984-01-01

    Compatible integration of detectors and readout electronics on the same silicon substrate is of growing interest. As the methods of microelectronics technology have already been adapted for detector fabrication, a common technology basis for detectors and readout electronics is available. CMOS technology exhibits most attractive features for the compatible realization of readout electronics when advanced LSI processing steps are combined with detector requirements. The essential requirements for compatible integration are the availability of high resistivity (100)-oriented single crystalline silicon substrate, the formation of suitably doped areas for MOS circuits and the isolation of the low voltage circuit from the detector operated at much higher supply voltage. Junction isolation as a first approach based on present production technology and dielectric isolation based on an advanced SOI-LSI technology are discussed as the most promising solutions for present and future applications, respectively. (orig.)

  18. NASA/DoD Aerospace Knowledge Diffusion Research Project. XXXIII - Technical communications practices and the use of information technologies as reported by Dutch and U.S. aerospace engineers

    Science.gov (United States)

    Barclay, Rebecca O.; Pinelli, Thomas E.; Tan, Axel S. T.; Kennedy, John M.

    1993-01-01

    As part of Phase 4 of the NASA/DOD Aerospace Knowledge Diffusion Research Project, two studies were conducted that investigated the technical communications practices of Dutch and U.S. aerospace engineers and scientists. A self-administered questionnaire was distributed to aerospace engineers and scientists at the National Aerospace Laboratory (The Netherlands), and NASA Ames Research Center (U.S.), and the NASA Langley Research Center (U.S.). This paper presents responses of the Dutch and U.S. participants to selected questions about four of the seven project objectives: determining the importance of technical communications to aerospace engineering professionals, investigating the production of technical communications, examining the use and importance of computer and information technology, and exploring the use of electronic networks.

  19. High power electron and ion beam research and technology

    Energy Technology Data Exchange (ETDEWEB)

    Nation, J.A.; Sudan, R.N. (eds.)

    1977-01-01

    Topics covered in volume II include: collective accelerators; microwaves and unneutralized E-beams; technology of high-current E-beam accelerators and laser applications of charged-particle beams. Abstracts of twenty-nine papers from the conference were prepared for the data base in addition to six which appeared previously. (GHT)

  20. Electronic Commerce: Canadian Community Colleges and Institutes of Technology.

    Science.gov (United States)

    Association of Canadian Community Colleges.

    This paper reports on the Canadian college system's collaboration with industry and community services in the development and delivery of non-credit e-commerce courses offered through continuing education departments at community colleges and institutes of technology. The paper argues that, in today's changing economy, the accelerated need for…

  1. Project-Based Learning in Electronic Technology: A Case Study

    Science.gov (United States)

    Li, Li

    2015-01-01

    A case study of project-based learning (PBL) implemented in Tianjin University of Technology and Education is presented. This multidiscipline project is innovated to meet the novel requirements of industry while keeping its traditional effectiveness in driving students to apply knowledge to practice and problem-solving. The implementation of PBL…

  2. Technical Report on the Development of Novel Technology for Reducing the Toxicity of Mistletoe Lectin by using Radiation Fusion Technology

    International Nuclear Information System (INIS)

    Lee, Ju Woon; Kim, Jae Hun; Choi, Jong Il; Song, Beom Seok; Yoon, Yo Han; Jung, Pil Mun; Sung, Nak Yun

    2009-10-01

    The aim of this study was conducted to investigate the effect of irradiation on detoxification, structural change, and physiological change of Mistletoe lectin. Optimal irradiation dose was determined from the result of having maximum detoxification and remaining the immunological activity Irradiation technology could be effective method for detoxification of Mistletoe lectin containing the immunological activity. The results indicate the feasibility of novel technology for reduction of the toxicity of Mistletoe lectin by using radiation technology. Practical state though clinical test is needed to extend biomedicine field using radiation technology and improve of public health by the control of the disease that gradually increase every year

  3. Development of superconductor electronics technology for high-end computing

    Energy Technology Data Exchange (ETDEWEB)

    Silver, A [Jet Propulsion Laboratory, 4800 Oak Grove Drive, Pasadena, CA 91109-8099 (United States); Kleinsasser, A [Jet Propulsion Laboratory, 4800 Oak Grove Drive, Pasadena, CA 91109-8099 (United States); Kerber, G [Northrop Grumman Space Technology, One Space Park, Redondo Beach, CA 90278 (United States); Herr, Q [Northrop Grumman Space Technology, One Space Park, Redondo Beach, CA 90278 (United States); Dorojevets, M [Department of Electrical and Computer Engineering, SUNY-Stony Brook, NY 11794-2350 (United States); Bunyk, P [Northrop Grumman Space Technology, One Space Park, Redondo Beach, CA 90278 (United States); Abelson, L [Northrop Grumman Space Technology, One Space Park, Redondo Beach, CA 90278 (United States)

    2003-12-01

    This paper describes our programme to develop and demonstrate ultra-high performance single flux quantum (SFQ) VLSI technology that will enable superconducting digital processors for petaFLOPS-scale computing. In the hybrid technology, multi-threaded architecture, the computational engine to power a petaFLOPS machine at affordable power will consist of 4096 SFQ multi-chip processors, with 50 to 100 GHz clock frequency and associated cryogenic RAM. We present the superconducting technology requirements, progress to date and our plan to meet these requirements. We improved SFQ Nb VLSI by two generations, to a 8 kA cm{sup -2}, 1.25 {mu}m junction process, incorporated new CAD tools into our methodology, demonstrated methods for recycling the bias current and data communication at speeds up to 60 Gb s{sup -1}, both on and between chips through passive transmission lines. FLUX-1 is the most ambitious project implemented in SFQ technology to date, a prototype general-purpose 8 bit microprocessor chip. We are testing the FLUX-1 chip (5K gates, 20 GHz clock) and designing a 32 bit floating-point SFQ multiplier with vector-register memory. We report correct operation of the complete stripline-connected gate library with large bias margins, as well as several larger functional units used in FLUX-1. The next stage will be an SFQ multi-processor machine. Important challenges include further reducing chip supply current and on-chip power dissipation, developing at least 64 kbit, sub-nanosecond cryogenic RAM chips, developing thermally and electrically efficient high data rate cryogenic-to-ambient input/output technology and improving Nb VLSI to increase gate density.

  4. Development of superconductor electronics technology for high-end computing

    International Nuclear Information System (INIS)

    Silver, A; Kleinsasser, A; Kerber, G; Herr, Q; Dorojevets, M; Bunyk, P; Abelson, L

    2003-01-01

    This paper describes our programme to develop and demonstrate ultra-high performance single flux quantum (SFQ) VLSI technology that will enable superconducting digital processors for petaFLOPS-scale computing. In the hybrid technology, multi-threaded architecture, the computational engine to power a petaFLOPS machine at affordable power will consist of 4096 SFQ multi-chip processors, with 50 to 100 GHz clock frequency and associated cryogenic RAM. We present the superconducting technology requirements, progress to date and our plan to meet these requirements. We improved SFQ Nb VLSI by two generations, to a 8 kA cm -2 , 1.25 μm junction process, incorporated new CAD tools into our methodology, demonstrated methods for recycling the bias current and data communication at speeds up to 60 Gb s -1 , both on and between chips through passive transmission lines. FLUX-1 is the most ambitious project implemented in SFQ technology to date, a prototype general-purpose 8 bit microprocessor chip. We are testing the FLUX-1 chip (5K gates, 20 GHz clock) and designing a 32 bit floating-point SFQ multiplier with vector-register memory. We report correct operation of the complete stripline-connected gate library with large bias margins, as well as several larger functional units used in FLUX-1. The next stage will be an SFQ multi-processor machine. Important challenges include further reducing chip supply current and on-chip power dissipation, developing at least 64 kbit, sub-nanosecond cryogenic RAM chips, developing thermally and electrically efficient high data rate cryogenic-to-ambient input/output technology and improving Nb VLSI to increase gate density

  5. Development of electron beam flue gas treatment technology

    International Nuclear Information System (INIS)

    Tokunaga, Okihiro; Namba, Hideki; Tanaka, Tadashi; Ogura, Yoshimi; Doi, Yoshitake; Aoki, Shinji; Izutsu, Masahiro.

    1995-01-01

    Smoke treatment system making use of electron beam irradiation made it possible to simultaneously eliminate SOx and NOn from exhaust gas. The fundamental study of the system was started in the seventies and at present, its application in practical use is under way. A pilot plant for the smoke treatment system was constructed in cooperation of Chubu Electric Power Company, Inc., Japan Atomic Energy Research Institute and Ebara Corporation and several tests with the actual exhaust gas were conducted during the period, Oct. 1992-Dec. 1993 and the treatment efficiency and the control capacity of this system was confirmed to be so high as the conventional systems and many engineering data were obtained. A high treatment efficiency (>94% for desulfurization and >80% for denitrification) was obtainable by choosing the optimum irradiation amount of electron beam and the optimum temperature of gas to treat. And this system was found superior from a financial aspect to the conventional smoke treatment system. (M.N.)

  6. Linking emerging hazardous waste technologies with the electronic information era

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, B.E.; Suk, W.A. [National Institute of Environmental Health Sciences, Research Triangle Park, NC (United States); Blackard, B. [Technology Planning and Management Corp., Durham, NC (United States)

    1996-12-31

    In looking to the future and the development of new approaches or strategies for managing hazardous waste, it is important to understand and appreciate the factors that have contributed to current successful approaches. In the United States, several events in the last two decades have had a significant impact in advancing remediation of hazardous waste, including environmental legislation, legislative reforms on licensing federally funded research, and electronic transfer of information. Similar activities also have occurred on a global level. While each of these areas is significant, the electronic exchange of information has no national boundaries and has become an active part of major hazardous waste research and management programs. It is important to realize that any group or society that is developing a comprehensive program in hazardous waste management should be able to take advantage of this advanced approach in the dissemination of information. 6 refs., 1 tab.

  7. A decision technology system for health care electronic commerce.

    Science.gov (United States)

    Forgionne, G A; Gangopadhyay, A; Klein, J A; Eckhardt, R

    1999-08-01

    Mounting costs have escalated the pressure on health care providers and payers to improve decision making and control expenses. Transactions to form the needed decision data will routinely flow, often electronically, between the affected parties. Conventional health care information systems facilitate flow, process transactions, and generate useful decision information. Typically, such support is offered through a series of stand-alone systems that lose much useful decision knowledge and wisdom during health care electronic commerce (e-commerce). Integrating the stand-alone functions can enhance the quality and efficiency of the segmented support, create synergistic effects, and augment decision-making performance and value for both providers and payers. This article presents an information system that can provide complete and integrated support for e-commerce-based health care decision making. The article describes health care e-commerce, presents the system, examines the system's potential use and benefits, and draws implications for health care management and practice.

  8. Electron acceleration by laser fields in a gas: Technical progress report

    International Nuclear Information System (INIS)

    Fontana, J.R.

    1987-01-01

    Alternative media are considered for inverse Cherenkov interactions, with refractive indices given for several neutral gases. Breakdown considerations are taken into account as well as elastic collisions. Properties of ionized gases are also discussed as they relate to the usefulness of plasmas as accelerator media. The planning for inverse Cherenkov interaction experiments at a CO 2 laser, 50 MeV electron linac test facility is being carried out

  9. Electronic Health Record developed by the Internet technology

    OpenAIRE

    吉原, 博幸; Yoshihara, Hiroyuki

    1998-01-01

    Installation of the order entry system had been done in the college hospital. However, Installation of the order entry system has just begun in middle sized hospitals. On the other hand, at the middle sized hospitals which does not equipped with the order entry system, the administrator is considering to install the electronic health record system rather than to install the order entry system, In case of small hospitals, there is no merit of installing the order entry system. So, many young d...

  10. TECHNICAL NOTE: Portable audio electronics for impedance-based measurements in microfluidics

    Science.gov (United States)

    Wood, Paul; Sinton, David

    2010-08-01

    We demonstrate the use of audio electronics-based signals to perform on-chip electrochemical measurements. Cell phones and portable music players are examples of consumer electronics that are easily operated and are ubiquitous worldwide. Audio output (play) and input (record) signals are voltage based and contain frequency and amplitude information. A cell phone, laptop soundcard and two compact audio players are compared with respect to frequency response; the laptop soundcard provides the most uniform frequency response, while the cell phone performance is found to be insufficient. The audio signals in the common portable music players and laptop soundcard operate in the range of 20 Hz to 20 kHz and are found to be applicable, as voltage input and output signals, to impedance-based electrochemical measurements in microfluidic systems. Validated impedance-based measurements of concentration (0.1-50 mM), flow rate (2-120 µL min-1) and particle detection (32 µm diameter) are demonstrated. The prevailing, lossless, wave audio file format is found to be suitable for data transmission to and from external sources, such as a centralized lab, and the cost of all hardware (in addition to audio devices) is ~10 USD. The utility demonstrated here, in combination with the ubiquitous nature of portable audio electronics, presents new opportunities for impedance-based measurements in portable microfluidic systems.

  11. Advanced methods for teaching electronic-nose technologies to diagnosticians and clinical laboratory technicians

    Science.gov (United States)

    Alphus D. Wilson

    2012-01-01

    Electronic-detection technologies and instruments increasingly are being utilized in the biomedical field to perform a wide variety of clinical operations and laboratory analyses to facilitate the delivery of health care to patients. The introduction of improved electronic instruments for diagnosing diseases and for administering treatments has required new training of...

  12. Organic electronics: materials, technology and circuit design developments enabling new applications

    NARCIS (Netherlands)

    Leeuw, de D.M.; Cantatore, E.

    2009-01-01

    Organic electronics is growing to become an important new field in the global electronics market. RFID labels, flexible displays, solar cells, OLED-based lighting and displays are only some of the innovative products enabled by technologies based on organic semiconductors. Starting from a short

  13. Future applications of electronic-nose technologies in healthcare and biomedicine

    Science.gov (United States)

    Alphus D. Wilson

    2011-01-01

    The development and utilization of many new electronic-nose (e-nose) applications in the healthcare and biomedical fields have continued to rapidly accelerate over the past 20 years. Innovative e-nose technologies are providing unique solutions to a diversity of complex problems in biomedicine that are now coming to fruition. A wide range of electronic-nose instrument...

  14. DEMONSTRATION BULLETIN: HIGH VOLTAGE ELECTRON BEAM TECHNOLOGY - HIGH VOLTAGE ENVIRONMENTAL APPLICATIONS, INC.

    Science.gov (United States)

    The high energy electron beam irradiation technology is a low temperature method for destroying complex mixtures of hazardous organic chemicals in solutions containing solids. The system consists of a computer-automated, portable electron beam accelerator and a delivery system. T...

  15. Technologies in computerized lexicography | Kruyt | Lexikos

    African Journals Online (AJOL)

    Although the topic of this paper is technology, focus is on functional rather than technical aspects of computerized lexicography. Keywords: computerized lexicography, electronic dictionary, electronic text corpus, lexicographer's workbench, integrated language database, automatic linguistic analysis, information retrieval, ...

  16. Electronics

    Science.gov (United States)

    2001-01-01

    International Acer Incorporated, Hsin Chu, Taiwan Aerospace Industrial Development Corporation, Taichung, Taiwan American Institute of Taiwan, Taipei, Taiwan...Singapore and Malaysia .5 - 4 - The largest market for semiconductor products is the high technology consumer electronics industry that consumes up...Singapore, and Malaysia . A new semiconductor facility costs around $3 billion to build and takes about two years to become operational

  17. Technical and economic feasibility of development innovative technological solutions for expansion the adjustment range of high-power CCP

    Science.gov (United States)

    Arakelyan, E. K.; Andryushin, A. V.; Burtsev, S. Y.; Andryushin, K. A.

    2017-11-01

    The analysis of technical and parametric constraints on the adjustment range of highpower CCP and recommended technological solutions in the technical literature for their elimination. Established that in the conditions of toughening the requirements for economy, reliability and maneuverability on the part of the system operator with the participation of CCP in control the frequency and power in the power system, existing methods do not ensure the fulfillment of these requirements. The current situation in the energy sector — the lack of highly manoeuvrable power equipment leads to the need participate in control of power consumption diagrams for all types of power plants, including CCP, although initially they were intended primarily for basic loads. Large-scale research conducted at the department of Automated control systems of technological processes, showed the possibility of a significant expansion of the adjustment range of CCP when it operating in the condensing mode and in the heating mode. The report presents the main results of these research for example the CCP-450 and CCP-450T. Various technological solutions are considered: when CCP in the condensation mode — the use of bypass steam distribution schemes, the transfer of a part of the steam turbine into a low-steam mode; when CCP operation in the heating mode — bypass steam distribution and the transfer CCP to gas turbine unit — power heating plants mode with the transfer the steam turbine to the motor mode. Data on the evaluation of the technical and economic feasibility of the proposed innovative technological solutions are presented in comparison with the methods used to solve this problem, which are used in practice, such as passing through the failures of the electric load graphs by transferring the CCP to the mode of operation with incomplete equipment. When comparing, both the economics, and the maneuverability and reliability of the equipment are considered.

  18. Projects at the Western Environmental Technology Office. Quarterly technical progress report, April 1--June 30, 1995

    International Nuclear Information System (INIS)

    1995-01-01

    This report contains brief outlines of the multiple projects under the responsibility of the Western Environmental Technology Office in Butte Montana. These projects include biomass remediation, remediation of contaminated soils, mine waste technology, and several other types of remediation

  19. Technology Trust in Internet-Based Interorganizational Electronic Commerce

    OpenAIRE

    Pauline Ratnasingam; Paul A. Pavlou

    2003-01-01

    Trust in Internet-based Business-to-Business (B2B) e-commerce is an important issue for both practicioners and academicians. Whereas the traditional notion of dyadic interfirm trust primarily focuses on trust in a trading partner firm, trust in e-commerce also implicitly incorporates the notion of trust in the transaction infrastructure and underlying control mechanisms (technology trust), which deals with transaction integrity, authentication, confidentliality, non-repudiation, and best busi...

  20. Blockchain Technology: A new secured Electronic Health Record System

    OpenAIRE

    Tamazirt , Lotfi; Alilat , Farid; Agoulmine , Nazim

    2018-01-01

    International audience; Nowadays, health systems are looking for effective ways to manage more patients in a shorter time, and to increase the quality of care through better coordination to provide quick, accurate and non-invasive diagnostics to patients. This paper aims to solve the dependence on trusted third parties by proposing a new management strategy, storage and security in a decentralized network through Blockchain technology. The proposed system also aims to offer a solution to help...

  1. The interplay of institutions, actors and technologies in socio-technical systems - An analysis of transformations in the Australian urban water sector

    NARCIS (Netherlands)

    Fuenfschilling, Lea; Truffer, Bernhard

    2016-01-01

    Literature on socio-technical transitions has primarily emphasized the co-determination of institutions and technologies. In this paper, we want to focus on how actors play a mediating role between these two pillars of a socio-technical system. By introducing the theoretical concept of institutional

  2. Traditional Craft or Technology Education: Development of Students' Technical Abilities in Finnish Comprehensive School

    Science.gov (United States)

    Autio, Ossi

    2016-01-01

    Changes in the economy, nature, production and society together with increasing scientific and technological knowledge make demands of transforming school teaching in the field of technology education. The aim of the article is briefly to explore the integration between science, technology and traditional craft education by analyzing the current…

  3. Technological Education for the Rural Community (TERC) Project: Technical Mathematics for the Advanced Manufacturing Technician

    Science.gov (United States)

    McCormack, Sherry L.; Zieman, Stuart

    2017-01-01

    Hopkinsville Community College's Technological Education for the Rural Community (TERC) project is funded through the National Science Foundation Advanced Technological Education (NSF ATE) division. It is advancing innovative educational pathways for technological education promoted at the community college level serving rural communities to fill…

  4. Discovering Hidden Resources: Assistive Technology Recycling, Refurbishing, and Redistribution. RESNA Technical Assistance Project.

    Science.gov (United States)

    RESNA: Association for the Advancement of Rehabilitation Technology, Arlington, VA.

    This monograph discusses the benefits of recycling and reusing assistive technology for students with disabilities. It begins by discussing the benefits of recycled assistive technology for suppliers, students, and consumers, and then profiles programmatic models for assistive technology recycling programs. The advantages and disadvantages for…

  5. Technological change in Swiss thermal waste treatment: An expert-based socio-technical analysis

    International Nuclear Information System (INIS)

    Spoerri, Andy; Lang, Daniel J.; Staeubli, Beat; Scholz, Roland W.

    2010-01-01

    Understanding technological change provides a crucial basis for governing sustainability transitions. In this paper we present an analysis of technological change using the example of Swiss thermal waste processing. In recent years, increased concerns about the low quality of residues from grate-firing systems led to the examination of alternative technologies. Yet despite clear indications of a potential better performance with respect to residue quality, none of these alternatives has been adopted. Based on a two-stage knowledge integration among 15 leading experts, in a retrospective analysis we identified factors that have significantly affected technological change in Swiss thermal waste processing. These factors were then related to three technological options representing different types of technological change, i.e., from incremental improvements of the existing to the implementation of a new technology. The results indicate that technological change is currently in a technological lock-in and provide detailed insights on the causes. The lock-in results in the step-wise further development of the status quo grate-firing system despite its limitations for improving the residue qualities. Almost all factors (legal, economic, societal, technological) of the existing 'thermal waste management' system have been well adapted to the cost- and energy-efficient grate-firing technology, blocking innovative technologies from entering the Swiss market. In addition, pressures from the context, e.g., societal pressure related to landfill risks, have not been strong enough to promote non-incremental change.

  6. Data description and quality assessment of ionospheric electron density profiles for ARPA modeling project. Technical report

    International Nuclear Information System (INIS)

    Conkright, R.O.

    1977-03-01

    This report presents a description of the automated method used to produce electron density (N(h)) profiles from ionograms recorded on 35mm film and an assessment of the resulting data base. A large data base of about 30,000 profiles was required for an ionospheric modeling project. This motivated a search for an automated method of producing profiles. The automated method used is fully described, the resulting data are given a quality grade, and the noon and midnight profiles are presented. Selected portions of this data base are compared with profiles produced by the standard profiling method in use by the Environmental Data Service at Boulder, Colorado

  7. New generation of compact electron accelerators for radiation technologies

    International Nuclear Information System (INIS)

    Auslender, V.L.; Balakin, V.E.; Kraynov, G.S.

    1995-01-01

    Compact electron accelerators with energy range 0.25-1.0 MeV and beam power up to 32 kw are described. The feeding high voltage is formed by converter (working frequency 20 khz), coreless step-up transformer and a set of rectifying sections. The rectifying multiplier circuit used in rectifying sections permits to reach voltage gradient along accelerator's axis up to 14 kV/cm. The accelerators with vertical and horizontal position are described. The accelerators can be produced together with local radiation shielding and various underbeam transportation systems for irradiation of different products. Such version can be installed in any room facing general requirements for electric equipment

  8. Missouri local technical assistance program at Missouri University of Science and Technology (formerly University of Missouri--Rolla) : annual progress report January-December 2007.

    Science.gov (United States)

    2009-02-01

    This annual report is a summary of the activities during 2007 for the Missouri Local Technical Assistance Program (Missouri LTAP), which is located at Missouri University of Science and Technology. The report highlights Missouri LTAPs performance ...

  9. Automated electronic monitoring of circuit pressures during continuous renal replacement therapy: a technical report.

    Science.gov (United States)

    Zhang, Ling; Baldwin, Ian; Zhu, Guijun; Tanaka, Aiko; Bellomo, Rinaldo

    2015-03-01

    Automated electronic monitoring and analysis of circuit pressures during continuous renal replacement therapy (CRRT) has the potential to predict failure and allow intervention to optimise function. Current CRRT machines can measure and store pressure readings for downloading into databases and for analysis. We developed a procedure to obtain such data at intervals of 1 minute and analyse them using the Prismaflex CRRT machine, and we present an example of such analysis. We obtained data on pressures obtained at intervals of 1 minute in a patient with acute kidney injury and sepsis treated with continuous haemofiltration at 2 L/hour of ultrafiltration and a blood flow of 200 mL/minute. Data analysis identified progressive increases in transmembrane pressure (TMP) and prefilter pressure (PFP) from time 0 until 33 hours or clotting. TMP increased from 104 mmHg to 313 mmHg and PFP increased from from 131 mmHg to 185 mmHg. Effluent pressure showed a progressive increase in the negative pressure applied to achieve ultrafiltration from 0 mmHg to -168 mmHg. The inflection point for such changes was also identified. Blood pathway pressures for access and return remained unchanged throughout. Automated electronic monitoring of circuit pressure during CRRT is possible and provides useful information on the evolution of circuit clotting.

  10. CMOS technology: a critical enabler for free-form electronics-based killer applications

    Science.gov (United States)

    Hussain, Muhammad M.; Hussain, Aftab M.; Hanna, Amir

    2016-05-01

    Complementary metal oxide semiconductor (CMOS) technology offers batch manufacturability by ultra-large-scaleintegration (ULSI) of high performance electronics with a performance/cost advantage and profound reliability. However, as of today their focus has been on rigid and bulky thin film based materials. Their applications have been limited to computation, communication, display and vehicular electronics. With the upcoming surge of Internet of Everything, we have critical opportunity to expand the world of electronics by bridging between CMOS technology and free form electronics which can be used as wearable, implantable and embedded form. The asymmetry of shape and softness of surface (skins) in natural living objects including human, other species, plants make them incompatible with the presently available uniformly shaped and rigidly structured today's CMOS electronics. But if we can break this barrier then we can use the physically free form electronics for applications like plant monitoring for expansion of agricultural productivity and quality, we can find monitoring and treatment focused consumer healthcare electronics - and many more creative applications. In our view, the fundamental challenge is to engage the mass users to materialize their creative ideas. Present form of electronics are too complex to understand, to work with and to use. By deploying game changing additive manufacturing, low-cost raw materials, transfer printing along with CMOS technology, we can potentially stick high quality CMOS electronics on any existing objects and embed such electronics into any future objects that will be made. The end goal is to make them smart to augment the quality of our life. We use a particular example on implantable electronics (brain machine interface) and its integration strategy enabled by CMOS device design and technology run path.

  11. CMOS technology: a critical enabler for free-form electronics-based killer applications

    KAUST Repository

    Hussain, Muhammad Mustafa

    2016-05-17

    Complementary metal oxide semiconductor (CMOS) technology offers batch manufacturability by ultra-large-scaleintegration (ULSI) of high performance electronics with a performance/cost advantage and profound reliability. However, as of today their focus has been on rigid and bulky thin film based materials. Their applications have been limited to computation, communication, display and vehicular electronics. With the upcoming surge of Internet of Everything, we have critical opportunity to expand the world of electronics by bridging between CMOS technology and free form electronics which can be used as wearable, implantable and embedded form. The asymmetry of shape and softness of surface (skins) in natural living objects including human, other species, plants make them incompatible with the presently available uniformly shaped and rigidly structured today’s CMOS electronics. But if we can break this barrier then we can use the physically free form electronics for applications like plant monitoring for expansion of agricultural productivity and quality, we can find monitoring and treatment focused consumer healthcare electronics – and many more creative applications. In our view, the fundamental challenge is to engage the mass users to materialize their creative ideas. Present form of electronics are too complex to understand, to work with and to use. By deploying game changing additive manufacturing, low-cost raw materials, transfer printing along with CMOS technology, we can potentially stick high quality CMOS electronics on any existing objects and embed such electronics into any future objects that will be made. The end goal is to make them smart to augment the quality of our life. We use a particular example on implantable electronics (brain machine interface) and its integration strategy enabled by CMOS device design and technology run path. © (2016) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE). Downloading of the abstract is

  12. Interface between technical physics and technological irradiation with reference to applications in vegetal and animal radiobiology

    International Nuclear Information System (INIS)

    Peteu, G.; Opris, M.

    1994-01-01

    The main goals of vegetal and animal radiobiology in a specific correlation with technical physics are the stimulation of germination and induced mutations; vegetal and animal food conservation, sterilization techniques, and modifications in the radiosensitivity of biological systems. The existing correlation between the effects of exposed and absorbed doses, and the behaviour of the 'microflora' (microbes, fungi), are discussed. (Author)

  13. Printing versus coating - What will be the future production technology for printed electronics?

    Energy Technology Data Exchange (ETDEWEB)

    Glawe, Andrea; Eggerath, Daniel; Schäfer, Frank [KROENERT GmbH and Co KG, Schuetzenstrasse 105, 22761 Hamburg (Germany)

    2015-02-17

    The market of Large Area Organic Printed Electronics is developing rapidly to increase efficiency and quality as well as to lower costs further. Applications for OPV, OLED, RFID and compact Printed Electronic systems are increasing. In order to make the final products more affordable, but at the same time highly accurate, Roll to Roll (R2R) production on flexible transparent polymer substrates is the way forward. There are numerous printing and coating technologies suitable depending on the design, the product application and the chemical process technology. Mainly the product design (size, pattern, repeatability) defines the application technology.

  14. Technology and equipment for processing diamond materials of modern electronics

    Directory of Open Access Journals (Sweden)

    Mityagin A. Yu.

    2009-02-01

    Full Text Available The methods of selection and sorting of diamonds according to their physical properties by modern physical methods of the analysis are developed, as well as the technologies of precision laser cutting of diamonds, their processing on a basis of thermochemical reactions in gas environment. The experimental installation for polishing and grinding of diamond plates, installation for slicing, installation for plasma-chemical processing are created. The techniques of surface roughness measurement of the processed plates and control of roughness parameters are developed. Some experimental results are given.

  15. Next Generation Nuclear Plant Project Technology Development Roadmaps: The Technical Path Forward for 750–800°C Reactor Outlet Temperature

    Energy Technology Data Exchange (ETDEWEB)

    John Collins

    2009-08-01

    This document presents the NGNP Critical PASSCs and defines their technical maturation path through Technology Development Roadmaps (TDRMs) and their associated Technology Readiness Levels (TRLs). As the critical PASSCs advance through increasing levels of technical maturity, project risk is reduced and the likelihood of within-budget and on-schedule completion is enhanced. The current supplier-generated TRLs and TDRMs for a 750–800°C reactor outlet temperature (ROT) specific to each supplier are collected in Appendix A.

  16. Applications of Organic and Printed Electronics A Technology-Enabled Revolution

    CERN Document Server

    2013-01-01

    Organic and printed electronics can enable a revolution in the applications of electronics and this book offers readers an overview of the state-of-the-art in this rapidly evolving domain.  The potentially low cost, compatibility with flexible substrates and the wealth of devices that characterize organic and printed electronics will make possible applications that go far beyond the well-known displays made with large-area silicon electronics. Since organic electronics are still in their early stage, undergoing transition from lab-scale and prototype activities to production, this book serves as a valuable snapshot of the current landscape of the different devices enabled by this technology, reviewing all applications that are developing and those can be foreseen.   Provides a complete roadmap for organic and printed electronics research and development for the next several years; Includes an overview of the printing processes for organic electronics, along with state of the art applications, such as solar ...

  17. Technical Progress Report on Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Bill Stanley; Patrick Gonzalez; Sandra Brown; Jenny Henman; Ben Poulter; Sarah Woodhouse Murdock; Neil Sampson; Tim Pearson; Sarah Walker; Zoe Kant; Miguel Calmon; Gilberto Tiepolo

    2006-06-30

    The Nature Conservancy is participating in a Cooperative Agreement with the Department of Energy (DOE) National Energy Technology Laboratory (NETL) to explore the compatibility of carbon sequestration in terrestrial ecosystems and the conservation of biodiversity. The title of the research project is ''Application and Development of Appropriate Tools and Technologies for Cost-Effective Carbon Sequestration''. The objectives of the project are to: (1) improve carbon offset estimates produced in both the planning and implementation phases of projects; (2) build valid and standardized approaches to estimate project carbon benefits at a reasonable cost; and (3) lay the groundwork for implementing cost-effective projects, providing new testing ground for biodiversity protection and restoration projects that store additional atmospheric carbon. This Technical Progress Report discusses preliminary results of the six specific tasks that The Nature Conservancy is undertaking to answer research needs while facilitating the development of real projects with measurable greenhouse gas reductions. The research described in this report occurred between April 1st and July 30th 2006. The specific tasks discussed include: Task 1: carbon inventory advancements; Task 2: emerging technologies for remote sensing of terrestrial carbon; Task 3: baseline method development; Task 4: third-party technical advisory panel meetings; Task 5: new project feasibility studies; and Task 6: development of new project software screening tool. Work is being carried out in Brazil, Belize, Chile, Peru and the USA.

  18. Defining the “proven technology” technical criterion in the reactor technology assessment for Malaysia’s nuclear power program

    International Nuclear Information System (INIS)

    Anuar, Nuraslinda; Kahar, Wan Shakirah Wan Abdul; Manan, Jamal Abdul Nasir Abd

    2015-01-01

    Developing countries that are considering the deployment of nuclear power plants (NPPs) in the near future need to perform reactor technology assessment (RTA) in order to select the most suitable reactor design. The International Atomic Energy Agency (IAEA) reported in the Common User Considerations (CUC) document that “proven technology” is one of the most important technical criteria for newcomer countries in performing the RTA. The qualitative description of five desired features for “proven technology” is relatively broad and only provides a general guideline to its characterization. This paper proposes a methodology to define the “proven technology” term according to a specific country’s requirements using a three-stage evaluation process. The first evaluation stage screens the available technologies in the market against a predefined minimum Technology Readiness Level (TRL) derived as a condition based on national needs and policy objectives. The result is a list of technology options, which are then assessed in the second evaluation stage against quantitative definitions of CUC desired features for proven technology. The potential technology candidates produced from this evaluation is further narrowed down to obtain a list of proven technology candidates by assessing them against selected risk criteria and the established maximum allowable total score using a scoring matrix. The outcome of this methodology is the proven technology candidates selected using an accurate definition of “proven technology” that fulfills the policy objectives, national needs and risk, and country-specific CUC desired features of the country that performs this assessment. A simplified assessment for Malaysia is carried out to demonstrate and suggest the use of the proposed methodology. In this exercise, ABWR, AP1000, APR1400 and EPR designs assumed the top-ranks of proven technology candidates according to Malaysia’s definition of “proven technology”

  19. Defining the “proven technology” technical criterion in the reactor technology assessment for Malaysia’s nuclear power program

    Energy Technology Data Exchange (ETDEWEB)

    Anuar, Nuraslinda, E-mail: nuraslinda@uniten.edu.my [College of Engineering, Universiti Tenaga Nasional, Jalan IKRAM-UNITEN, 43000 Kajang, Selangor (Malaysia); Kahar, Wan Shakirah Wan Abdul, E-mail: shakirah@tnb.com.my; Manan, Jamal Abdul Nasir Abd [Nuclear Energy Department, Regulatory Economics and Planning Division, Tenaga Nasional Berhad, No. 8 Jalan Tun Sambanthan, Brickfields, 50470 Kuala Lumpur (Malaysia)

    2015-04-29

    Developing countries that are considering the deployment of nuclear power plants (NPPs) in the near future need to perform reactor technology assessment (RTA) in order to select the most suitable reactor design. The International Atomic Energy Agency (IAEA) reported in the Common User Considerations (CUC) document that “proven technology” is one of the most important technical criteria for newcomer countries in performing the RTA. The qualitative description of five desired features for “proven technology” is relatively broad and only provides a general guideline to its characterization. This paper proposes a methodology to define the “proven technology” term according to a specific country’s requirements using a three-stage evaluation process. The first evaluation stage screens the available technologies in the market against a predefined minimum Technology Readiness Level (TRL) derived as a condition based on national needs and policy objectives. The result is a list of technology options, which are then assessed in the second evaluation stage against quantitative definitions of CUC desired features for proven technology. The potential technology candidates produced from this evaluation is further narrowed down to obtain a list of proven technology candidates by assessing them against selected risk criteria and the established maximum allowable total score using a scoring matrix. The outcome of this methodology is the proven technology candidates selected using an accurate definition of “proven technology” that fulfills the policy objectives, national needs and risk, and country-specific CUC desired features of the country that performs this assessment. A simplified assessment for Malaysia is carried out to demonstrate and suggest the use of the proposed methodology. In this exercise, ABWR, AP1000, APR1400 and EPR designs assumed the top-ranks of proven technology candidates according to Malaysia’s definition of “proven technology”.

  20. Technical innovation and management

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Yang Cheol

    1982-08-15

    This book gives explanations of the conception of technical innovation, development plan in Korea, connection between technology and a growth factor in national income, problem of technical innovation in developing country, analysis on cooperation between a developed country and a developing country, evaluation and strategy of technical development in Korea, technical innovation of industry, management of technical industry, analysis of special condition in Korea.