Electroluminescent devices based on rare-earth tetrakis β-diketonate complexes

International Nuclear Information System (INIS)

Quirino, W.G.; Legnani, C.; Santos, R.M.B. dos; Teixeira, K.C.; Cremona, M.; Guedes, M.A.; Brito, H.F.

2008-01-01

In this paper the synthesis, photoluminescence and electroluminescence investigation of the novel tetrakis β-diketonate of rare-earth complexes such as, M[Eu(dbm) 4 ] and M[Tb(acac) 4 ] with a variety of cationic ligands, M = Li + , Na + and K + have been investigated. The emission spectra of the Eu 3+ and Tb 3+ complexes displayed characteristic narrow bands arising from intraconfigurational transitions of trivalent rare-earth ions and exhibited red color emission for the Eu 3+ ion ( 5 D 0 → 7 F J , J = 0-6) and green for the Tb 3+ ion ( 5 D 4 → 7 F J , J = 6-0). The lack of the broaden emission bands arising from the ligands suggests the efficient intramolecular energy transfer from the dbm and acac ligands to Eu 3+ and Tb 3+ ions, respectively. In accordance to the expected, the values of PL quantum efficiency (η) of the emitting 5 D 0 state of the tetrakis(β-diketonate) complexes of Eu 3+ were higher compared with those tris-complexes. Therefore, organic electroluminescent (EL) devices were fabricated with the structure as follows: indium tin oxide (ITO)/hole transport layer (HTL) NPB or MTCD/emitter layer M[RE(β-diketonate) 4 ] complexes)/Aluminum (Al). All the films were deposited by thermal evaporation carried out in a high vacuum environment system. The OLED light emission was independent of driving voltage, indicating that the combination of charge carriers generates excitons within the M[RE(β-diketonate) 4 ] layers, and the energy is efficiently transferred to RE 3+ ion. As a best result, a pure red and green electroluminescent emission was observed from the Eu 3+ and Tb 3+ devices, confirmed by (X,Y) color coordinates

Tunable magneto-conductance and magneto-electroluminescence in polymer light-emitting electrochemical planar devices

Energy Technology Data Exchange (ETDEWEB)

Geng, R.; Mayhew, N. T.; Nguyen, T. D., E-mail: ngtho@uga.edu [Department of Physics and Astronomy, University of Georgia, Athens, Georgia 30602 (United States)

2013-12-09

We report studies of magneto-conductance (MC) and magneto-electroluminescence (MEL) in polymer light-emitting electrochemical planar devices using “super-yellow” poly-(phenylene vinylene). We observed consistent negative MC while MEL becomes positive when electroluminescence quantum efficiency (ELQE) increases. At an optimal ELQE, the MC has a much narrower width than the MEL, indicating that the MC and MEL do not share a common origin. However, MC reverses and has the same width as MEL when exposed to a threshold laser power. We show that the e-h pair model can explain the positive MEL and MC while the negative MC can be explained by the bipolaron model.

Tunable magneto-conductance and magneto-electroluminescence in polymer light-emitting electrochemical planar devices

International Nuclear Information System (INIS)

Geng, R.; Mayhew, N. T.; Nguyen, T. D.

2013-01-01

We report studies of magneto-conductance (MC) and magneto-electroluminescence (MEL) in polymer light-emitting electrochemical planar devices using “super-yellow” poly-(phenylene vinylene). We observed consistent negative MC while MEL becomes positive when electroluminescence quantum efficiency (ELQE) increases. At an optimal ELQE, the MC has a much narrower width than the MEL, indicating that the MC and MEL do not share a common origin. However, MC reverses and has the same width as MEL when exposed to a threshold laser power. We show that the e-h pair model can explain the positive MEL and MC while the negative MC can be explained by the bipolaron model

Progress and Prospects in Stretchable Electroluminescent Devices

Directory of Open Access Journals (Sweden)

Wang Jiangxin

2017-03-01

Full Text Available Stretchable electroluminescent (EL devices are a new form of mechanically deformable electronics that are gaining increasing interests and believed to be one of the essential technologies for next generation lighting and display applications. Apart from the simple bending capability in flexible EL devices, the stretchable EL devices are required to withstand larger mechanical deformations and accommodate stretching strain beyond 10%. The excellent mechanical conformability in these devices enables their applications in rigorous mechanical conditions such as flexing, twisting, stretching, and folding.The stretchable EL devices can be conformably wrapped onto arbitrary curvilinear surface and respond seamlessly to the external or internal forces, leading to unprecedented applications that cannot be addressed with conventional technologies. For example, they are in demand for wide applications in biomedical-related devices or sensors and soft interactive display systems, including activating devices for photosensitive drug, imaging apparatus for internal tissues, electronic skins, interactive input and output devices, robotics, and volumetric displays. With increasingly stringent demand on the mechanical requirements, the fabrication of stretchable EL device is encountering many challenges that are difficult to resolve. In this review, recent progresses in the stretchable EL devices are covered with a focus on the approaches that are adopted to tackle materials and process challenges in stretchable EL devices and delineate the strategies in stretchable electronics. We first introduce the emission mechanisms that have been successfully demonstrated on stretchable EL devices. Limitations and advantages of the different mechanisms for stretchable EL devices are also discussed. Representative reports are reviewed based on different structural and material strategies. Unprecedented applications that have been enabled by the stretchable EL devices are

A novel electroluminescent PPV copolymer and silsesquioxane nanocomposite film for the preparation of efficient PLED devices.

Science.gov (United States)

Venegoni, Ivan; Carniato, Fabio; Olivero, Francesco; Bisio, Chiara; Pira, Nello Li; Lambertini, Vito Guido; Marchese, Leonardo

2012-11-02

Polymer light-emitting diodes (PLEDs) have attracted growing interest in recent years for their potential use in displays and lighting fields. Nevertheless, PLED devices have some disadvantages in terms of low optoelectronic efficiency, high cost, short lifetimes and low thermal stability, which limit their final applications. Huge efforts have been made recently to improve the performances of these devices. The addition of inorganic or hybrid organic-inorganic nanoparticles to the light-emitting polymers, for example, allows their thermal stability and electroluminescent efficiency to be increased. Following this approach, novel PLED devices based on composite films of PPV-derivative copolymer (commercial name Super Yellow, SY) and octaisobutil POSS, were developed in this study. The device containing Super Yellow loaded with 1 wt% of POSS showed higher efficiency (ca. +30%) and improved lifetime in comparison to PLED prepared with the pure electroluminescent polymer. The PLED devices developed in this study are suitable candidates for automotive dashboards and, in general, for lighting applications.

Flexible electroluminescent device with inkjet-printed carbon nanotube electrodes

Science.gov (United States)

Azoubel, Suzanna; Shemesh, Shay; Magdassi, Shlomo

2012-08-01

Carbon nanotube (CNTs) inks may provide an effective route for producing flexible electronic devices by digital printing. In this paper we report on the formulation of highly concentrated aqueous CNT inks and demonstrate the fabrication of flexible electroluminescent (EL) devices by inkjet printing combined with wet coating. We also report, for the first time, on the formation of flexible EL devices in which all the electrodes are formed by inkjet printing of low-cost multi-walled carbon nanotubes (MWCNTs). Several flexible EL devices were fabricated by using different materials for the production of back and counter electrodes: ITO/MWCNT and MWCNT/MWCNT. Transparent electrodes were obtained either by coating a thin layer of the CNTs or by inkjet printing a grid which is composed of empty cells surrounded by MWCNTs. It was found that the conductivity and transparency of the electrodes are mainly controlled by the MWCNT film thickness, and that the dominant factor in the luminance intensity is the transparency of the electrode.

White-electroluminescent device with horizontally patterned blue/yellow phosphor-layer structure

International Nuclear Information System (INIS)

Won Park, Boo; Sik Choi, Nam; Won Park, Kwang; Mo Son, So; Kim, Jong Su; Kyun Shon, Pong

2007-01-01

White-electroluminescent (EL) devices with stripe-patterned and square-patterned phosphor-layer structures are fabricated through a screen printing method: electrode/BaTiO 3 insulator layer/patterned blue ZnS:Cu, Cl and yellow ZnS:Cu, Mn phosphor layer/ITO PET substrate. The luminous intensities of EL devices with stripe-patterned and square-patterned phosphor-layer structures are 33% and 23% higher than a conventional device with the phosphor-layer structure without any patterns using the phosphor blend. It can be explained in terms of the absorption of the emitted blue light of blue phosphor layer by the yellow-emitting phosphor layer. The EL device of our patterned phosphor-layer structure gives the possibility to enhance the luminance

Electroluminescence Properties of IrQ(ppy)2 Dual-Emitter Organometallic Compound in Organic Light-Emitting Devices

Science.gov (United States)

Ciobotaru, Constantin Claudiu; Polosan, Silviu; Ciobotaru, Iulia Corina

2018-02-01

This paper reports the influence of the charge carrier mobility on the electroluminescent properties of a dual-emitter organometallic compound dispersed in two conjugated organic small-molecule host materials and embedded in organic light-emitting devices (OLEDs). The electroluminescent processes in OLEDs are strongly influenced by the host-guest interaction. The charge carrier mobility in the host material plays an important role in the electroluminescent processes but also depends on the triplet-triplet interaction with the organometallic compound. The low charge carrier mobility in 4,4'-bis( N-carbazolyl)-1,1'-biphenyl (CBP) host material reduces the electroluminescent processes, but they are slightly enhanced by the triplet-triplet exothermic charge transfer. The higher charge carrier mobility in the case of N, N'-bis(3-methylphenyl)- N, N'-diphenylbenzidine (TPD) host material influences the electroluminescent processes by the endothermic energy transfer at room temperature, which facilitates the triplet-triplet harvesting in the host-guest system. The excitation is transferred to the guest molecules by triplet-triplet interaction as a Dexter transfer, which occurs by endothermic transfer from the triplet exciton in the host to the triplet exciton in the guest.

[The role of BCP in electroluminescence of multilayer organic light-emitting devices].

Science.gov (United States)

Deng, Zhao-Ru; Yang, Sheng-Yi; Lou, Zhi-Dong; Meng, Ling-Chuan

2009-03-01

As a hole-blocking layer, 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) is usually used in blue and white light electroluminescent devices. The ability of blocking holes of BCP layer depends on its thickness, and basically holes can tunnel through thin BCP layer. In order to know the role of BCP layer in electroluminescence (EL) of multilayer organic light-emitting diodes (OLEDs), in the present paper, the authors designed a multilayer OLED ITO/NPB/BCP/Alq3 : DCJTB/Alq3/Al and investigated the influence of thickness of BCP on the EL spectra of multilayer OLEDs at different applied voltages. The experimental data show that thin BCP layer can block holes partially and tune the energy transfer between different emissive layers, and in this way, it is easy to obtain white emission, but its EL spectra will change with the applied voltages. The EL spectra of multilayer device will remain relatively stable when BCP layer is thick enough, and the holes can hardly tunnel through when the thickness of BCP layer is more than 15 nm. Furthermore, the stability of EL spectra of the multilayer OLED at different applied voltages was discussed.

Large-area and bright pulsed electroluminescence in monolayer semiconductors

KAUST Repository

Lien, Der-Hsien; Amani, Matin; Desai, Sujay B.; Ahn, Geun Ho; Han, Kevin; He, Jr-Hau; Ager, Joel W.; Wu, Ming C.; Javey, Ali

2018-01-01

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS, WS, MoSe, and WSe) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.

Large-area and bright pulsed electroluminescence in monolayer semiconductors

KAUST Repository

Lien, Der-Hsien

2018-04-04

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS, WS, MoSe, and WSe) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.

Improved luminescence properties of nanocrystalline silicon based electroluminescent device by annealing

International Nuclear Information System (INIS)

Sato, Keisuke; Hirakuri, Kenji

2006-01-01

We report an annealing effect on electrical and luminescence properties of a red electroluminescent device consisting of nanocrystalline silicon (nc-Si). The red luminescence was generated by flowing the forward current into the device at a low threshold direct current (DC) forward voltage with a rise of annealing temperature up to 500 deg. C. Moreover, the luminescence of the device annealed at 500 deg. C was more intense than that of the device annealed at 200 deg. C or less under the same forward current density, because of the injection of a large quantity of carriers to the radiative recombination centers at the nc-Si surface vicinity. These were attained by a low resistivity of indium tin oxide (ITO) electrode and good contact at the ITO electrode/luminous layer interface region by the annealing treatment. The above results indicated that the annealing treatment of the device is effective for the realization of high luminance due to the improvement in the injection efficiency of carriers to the radiative recombination centers

Fabrication and performance of ACTFEL display devices using manganese-doped zinc germanate as a green-emitting electroluminescent layer

International Nuclear Information System (INIS)

Kim, Joo Han; Yoon, Kyung Ho

2010-01-01

Alternating-current thin-film electroluminescent (ACTFEL) display devices fabricated using manganese-doped zinc germanate (Zn 2 GeO 4 :Mn) as a green-emitting electroluminescent layer material are described. The ACTFEL display devices were fabricated with a standard bottom emission structure having a multilayer stack of thin films in the metal/semiconductor/insulator/ metal (MSIM) configuration. The device was constructed on a transparent Corning glass substrate through which the emitted EL light passed. The Zn 2 GeO 4 :Mn emission layer was synthesized by using a RF magnetron sputter deposition method, followed by post-annealing at 700 .deg. C in air ambient for 1 hour. The obtained Zn 2 GeO 4 :Mn films were found to be polycrystalline with a rhombohedral crystal structure. A green emission spectrum with a maximum at approximately 538 nm was produced from the fabricated device. The chromaticity color coordinates of the EL emission were measured to be x = 0.308 and y = 0.657. The device demonstrated a sharp increase in the intensity of green EL emission upon increasing the AC peak voltage applied to the device above a threshold of 148 V.

High-Color-Quality White Top-Emitting Organic Electroluminescent Devices Based on Both Exciton and Electroplex Emission

Science.gov (United States)

Zhang, Mingxiao; Chen, Zhijian; Xiao, Lixin; Qu, Bo; Gong, Qihuang

2011-08-01

A high-color-quality white top-emitting organic electroluminescent device (TOLED) with a simple structure was fabricated using both exciton and electroplex emission. White emission was achieved by combining the exciton emission of 4,4'-bis(2,2'-diphenylvinyl)-1,1'-biphenyl (DPVBi) and the broad band emission of electroplex generated between DPVBi and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP). The white emission spectra showed excellent stability at different bias voltages. By inserting a blend film of DPVBi:BCP and adjusting the ratio of DPVBi to BCP in the blend film, the CIE coordinates of the white emission can be tuned to (0.30, 0.33) and the electroluminescence efficiency can also be enhanced.

Electroluminescence dependence on the organic thickness in ZnO nano rods/Alq3 heterostructure devices.

Science.gov (United States)

Kan, Pengzhi; Wang, Yongsheng; Zhao, Suling; Xu, Zheng; Wang, Dawei

2011-04-01

ZnO nanorods are synthesised by a hydrothermal method on ITO glass. Their crystallization and morphology are detected by XRD and SEM, respectively. The results show that the ZnO nanorod array has grown primarily along a direction aligned perpendicular to the ITO substrate. The average height and diameter of the nanorods is about 130 nm and 30 nm, respectively. Then ZnO nano rods/Alq3 heterostructure LEDs are prepared by thermal evaporation of Alq3 molecules. The thicknesses of the Alq3 layers are 130 nm, 150 nm, 170 nm and 190 nm, respectively. The electroluminescence of the devices is detected under different DC bias voltages. The exciton emission of Alq3 is detected in all devices. When the thickness of Alq3 is 130 nm, the UV electroluminescence of ZnO is around 382 nm, and defect emissions around 670 nm and 740 nm are detected. Defect emissions of ZnO nanorods are prominent. When the thickness of Alq3 increases to over 170 nm, it is difficult to observe defect emissions from the ZnO nano rods. In such devices, the exciton emission of Alq3 is more prominent than other emissions under different bias voltage.

A Stretchable Alternating Current Electroluminescent Fiber

Directory of Open Access Journals (Sweden)

Dan Hu

2018-01-01

Full Text Available Flexible, stretchable electroluminescent fibers are of significance to meet the escalating requirements of increasing complexity and multifunctionality of smart electronics. We report a stretchable alternating current electroluminescent (ACEL fiber by a low-cost and all solution-processed scalable process. The ACEL fiber provides high stretchability, decent light-emitting performance, with excellent stability and nearly zero hysteresis. It can be stretched up to 80% strain. Our ACEL fiber device maintained a stable luminance for over 6000 stretch-release cycles at 50% strain. The mechanical stretchability and optical stability of our ACEL fiber device provides new possibilities towards next-generation stretchable displays, electronic textiles, advanced biomedical imaging and lighting, conformable visual readouts in arbitrary shapes, and novel health-monitoring devices.

An electroluminescence device for printable electronics using coprecipitated ZnS:Mn nanocrystal ink

International Nuclear Information System (INIS)

Toyama, T; Hama, T; Adachi, D; Nakashizu, Y; Okamoto, H

2009-01-01

Electroluminescence (EL) devices for printable electronics using coprecipitated ZnS:Mn nanocrystal (NC) ink are demonstrated. The EL properties of these devices were investigated along with the structural and optical properties of ZnS:Mn NCs with an emphasis on their dependence on crystal size. Transmission electron microscopy and x-ray diffraction studies revealed that the NCs, with a crystal size of 3-4 nm, are nearly monodisperse; the crystal size can be controlled by the Zn 2+ concentration in the starting solution for coprecipitation. The results of optical studies indicate the presence of quantum confinement effects; in addition, the NC surfaces are well passivated, regardless of the crystal size. Finally, an increase in the luminance of EL devices with a decrease in crystal size is observed, which suggests the excitation mechanism of ZnS:Mn NC EL devices.

Electroluminescence

CERN Document Server

Henisch, H K

1962-01-01

Electroluminescence deals with the multiplicity of forms related to electroluminescence phenomena. The book reviews some basic observations of electroluminescence, the Gudden-Pohl and Dechene effects, the electroluminescence phenomena in zinc sulfide phosphors, in silicon carbide, and in compounds composed of elements in groups III and V of the Periodic Table (such as gallium phosphide). The text also explains polarization of free charge carriers, the outline of junction breakdown theory, carrier recombination, and phosphor suspensions. The book describes the growth of zinc sulfide crystals (f

Efficient red organic electroluminescent devices based on trivalent europium complex obtained by designing the device structure with stepwise energy levels

Energy Technology Data Exchange (ETDEWEB)

Zhou, Liang; Jiang, Yunlong; Cui, Rongzhen; Li, Yanan; Zhao, Xuesen; Deng, Ruiping; Zhang, Hongjie, E-mail: hongjie@ciac.ac.cn

2016-02-15

In this study, we aim to further enhance the electroluminescence (EL) performances of trivalent europium complex Eu(TTA){sub 3}phen (TTA=thenoyltrifluoroacetone and phen=1,10-phenanthroline) by designing the device structure with stepwise energy levels. The widely used bipolar material 2,6-bis(3-(9H-carbazol-9-yl)phenyl)pyridine (26DCzPPy) was chosen as host material, while the doping concentration of Eu(TTA){sub 3}phen was optimized to be 4%. To facilitate the injection and transport of holes, MoO{sub 3} anode modification layer and 4,4′,4′′-Tris(carbazole-9-yl)triphenylamine (TcTa) hole transport layer were inserted in sequence. Efficient pure red emission with suppressed efficiency roll-off was obtained attributed to the reduction of accumulation holes, the broadening of recombination zone, and the improved balance of holes and electrons on Eu(TTA){sub 3}phen molecules. Finally, the device with 3 nm MoO{sub 3} and 5 nm TcTa obtained the highest brightness of 3278 cd/m{sup 2}, current efficiency of 12.45 cd/A, power efficiency of 11.50 lm/W, and external quantum efficiency of 6.60%. Such a device design strategy helps to improve the EL performances of emitters with low-lying energy levels and provides a chance to simplify device fabrication processes. - Highlights: • Electroluminescent performances of europium complex were further improved. • Device structure with stepwise energy levels was designed. • Better carriers' balance was realized by improving the injection and transport of holes. • The selection of bipolar host caused the broadening of recombination zone.

Yellow-green electroluminescence of samarium complexes of 8-hydroxyquinoline

Energy Technology Data Exchange (ETDEWEB)

Behzad, Sara Karimi; Najafi, Ezzatollah [Department of Chemistry Shahid Beheshti University G.C., Tehran 1983963113 (Iran, Islamic Republic of); Amini, Mostafa M., E-mail: m-pouramini@sbu.ac.ir [Department of Chemistry Shahid Beheshti University G.C., Tehran 1983963113 (Iran, Islamic Republic of); Janghouri, Mohammad; Mohajerani, Ezeddin [Laser Research Institute Shahid Beheshti University G.C., Tehran 1983963113 (Iran, Islamic Republic of); Ng, Seik Weng [Department of Chemistry, University of Malaya, 50603 Kuala Lumpur (Malaysia)

2014-12-15

Four novel samarium complexes were prepared by reacting samarium(III) nitrate with 8-hydroxyquinoline, 2-methyl-8-hydroxyquinoline, and 1,10-phenanthroline and utilized as emitting materials in the electroluminescence device. All complexes were characterized by elemental analysis, infrared, UV–vis and {sup 1}H NMR spectroscopes and the molecular structure of a representative complex, [Sm{sub 2}(Me-HQ){sub 4}(NO{sub 3}){sub 6}] (1), was determined by single-crystal X-ray diffraction. Utilization of a π-conjugated (phenanthroline) ligand as a second ligand in the structure of the samarium complexes resulted in red shifts in both absorption and fluorescence spectra of complexes and moderately enhanced the photoluminescence intensity and the fluorescence quantum yield. The maximum emission peaks showed that a good correlation exists between the nature of the substituent group on the 8-hydroxyquinoline and the addition of the π-conjugated ligand in the structure of samarium complexes and emission wavelength. Devices with samarium(III) complexes with structure of ITO/PEDOT:PSS (90 nm)/PVK:PBD:Sm(III) complexes (75 nm)/Al (180 nm) were fabricated. In the electroluminescence (EL) spectra of the devices, a strong ligand-centered emission and narrow bands arising from the {sup 4}G{sub 5/2}→{sup 6}H{sub J} transitions (J=7/2, 9/2, and 11/2) of the samarium ion were observed for the complexes. The electroluminescent spectra of the samarium complexes were red-shifted as compared with the PVK:PBD blend. We believe that the electroluminescence performance of OLED devices based on samarium complexes relies on overlaps between the absorption of the samarium compounds and the emission of PVK:PBD. This revealed that it is possible to evaluate the electroluminescence performance of the samarium compounds-doped OLED devices based on the emission of PVK:PBD and the absorption of the dopants. - Highlights: • Four novel photoluminescence samarium complexes have been synthesized. �

High performance yellow organic electroluminescent devices by doping iridium(III) complex into host materials with stepwise energy levels

Energy Technology Data Exchange (ETDEWEB)

Cui, Rongzhen; Zhou, Liang, E-mail: zhoul@ciac.ac.cn; Jiang, Yunlong; Li, Yanan; Zhao, Xuesen; Zhang, Hongjie, E-mail: hongjie@ciac.ac.cn

2015-10-15

In this work, we aim to further improve the electroluminescent (EL) performances of a yellow light-emitting iridium(III) complex by designing double light-emitting layers (EMLs) devices having stepwise energy levels. Compared with single-EML devices, these designed double-EML devices showed improved EL efficiency and brightness attributed to better balance in carriers. In addition, the stepwise distribution in energy levels of host materials is instrumental in broadening the recombination zone, thus delaying the roll-off of EL efficiency. Based on the investigation of carriers' distribution, device structure was further optimized by adjusting the thickness of deposited layers. Finally, yellow EL device (Commission Internationale de l'Eclairage (CIE) coordinates of (0.446, 0.542)) with maximum current efficiency, power efficiency and brightness up to 78.62 cd/A (external quantum efficiency (EQE) of 21.1%), 82.28 lm/W and 72,713 cd/m{sup 2}, respectively, was obtained. Even at the high brightness of 1000 cd/m{sup 2}, EL efficiency as high as 65.54 cd/A (EQE=17.6%) can be retained. - Highlights: • Yellow electroluminescent devices were designed and fabricated. • P-type and n-type materials having stepwise energy levels were chosen as host materials. • Better balance of holes and electrons causes the enhanced efficiencies. • Improved carriers' trapping suppresses the emission of host material.

Emission characteristics in solution-processed asymmetric white alternating current field-induced polymer electroluminescent devices

Science.gov (United States)

Chen, Yonghua; Xia, Yingdong; Smith, Gregory M.; Gu, Yu; Yang, Chuluo; Carroll, David L.

2013-01-01

In this work, the emission characteristics of a blue fluorophor poly(9, 9-dioctylfluorene) (PFO) combined with a red emitting dye: Bis(2-methyl-dibenzo[f,h]quinoxaline)(acetylacetonate)iridium (III) [Ir(MDQ)2(acac)], are examined in two different asymmetric white alternating current field-induced polymer electroluminescent (FIPEL) device structures. The first is a top-contact device in which the triplet transfer is observed resulting in the concentration-dependence of the emission similar to the standard organic light-emitting diode (OLED) structure. The second is a bottom-contact device which, however, exhibits concentration-independence of emission. Specifically, both dye emission and polymer emission are found for the concentrations as high as 10% by weight of the dye in the emitter. We attribute this to the significant different carrier injection characteristics of the two FIPEL devices. Our results suggest a simple and easy way to realize high-quality white emission.

High-performance alternating current field-induced chromatic-stable white polymer electroluminescent devices employing a down-conversion layer

Energy Technology Data Exchange (ETDEWEB)

Xia, Yingdong; Chen, Yonghua; Smith, Gregory M. [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Sun, Hengda; Yang, Dezhi [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Nie, Wanyi; Li, Yuan; Huang, Wenxiao [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Ma, Dongge [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Carroll, David L., E-mail: carroldl@wfu.edu [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States)

2015-05-15

In this work, a high-performance alternating current (AC) filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated by combining a fluorophor Poly(9,9-dioctylfluorene) (PFO)-based blue device with a yellow down-conversion layer (YAG:Ce). A maximum luminance of this down-conversion FIPEL device achieves 3230 cd m{sup −2}, which is 1.41 times higher than the device without the down-conversion layer. A maximum current efficiency and power efficiency of the down-conversion WFIPEL device reach 19.7 cd A{sup −1} at 3050 cd m{sup −2} and 5.37 lm W{sup −1} at 2310 cd m{sup −2} respectively. To the best of our knowledge, the power efficiency is one of the highest reports for the WFIPEL up to now. Moreover, Commison Internationale de L’Eclairage (CIE) coordinates of (0.28, 0.30) is obtained by adjusting the thickness of the down-conversion layer to 30 μm and it is kept stable over the entire AC-driven voltage range. We believe that this AC-driven, down-conversion, WFIPEL device may offer an easy way towards future flat and flexible lighting sources. - Highlights: • A high-performance AC filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated. • A maximum luminance, current efficiency, and power efficiency achieves 3230 cd m{sup −2}, 19.7 cd A{sup −1}, and 5.37 lm W{sup −1}, respectively. • The power efficiency is one of the highest reports for the WFIPEL up to now. • The EL spectrum kept very stable over the entire AC-driven voltage range.

Electroluminescent efficiency of alternating current thick film devices using ZnS:Cu,Cl phosphor

International Nuclear Information System (INIS)

Sharma, Gaytri; Han, Sang Do; Kim, Jung Duk; Khatkar, Satyender P.; Rhee, Young Woo

2006-01-01

ZnS:Cu,Cl phosphor is prepared with the help of low intensity milling of the precursor material in two step firing process. The synthesized phosphor is used for the preparation of alternating current thick film electroluminescent (ACTFEL) devices with screen-printing method. The commission international de l'Eclairge (CIE) color co-ordinates of the ACTFEL devices prepared by these phosphor layers shows a shift from bluish-green to green region with the change in the amount of Cu in the phosphor. The various parameters to improve the efficiency and luminance of the devices have also been investigated. The brightness of the ac thick film EL device depends on the particle size of the phosphor, crystallinity, amount of binding material and applied voltage. The EL device fabricated with phosphor having average particle size of 25 μm shows maximum luminescence, when 60% phosphor concentration is used with respect to binding material. EL intensity is also linearly dependent on frequency. It is due the increase of excitation chances of the host matrix or dopant ions with increasing frequency

Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

Directory of Open Access Journals (Sweden)

S.-T. Pham

2018-02-01

Full Text Available Magneto-electroluminescence (MEL effects are observed in single-layer organic light-emitting devices (OLEDs comprising only macrocyclic aromatic hydrocarbons (MAHs. The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6. The MEL ratio of the resulting OLED is 1%–2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (−1.5% to −2% in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

Science.gov (United States)

Pham, S.-T.; Ikemoto, K.; Suzuki, K. Z.; Izumi, T.; Taka, H.; Kita, H.; Sato, S.; Isobe, H.; Mizukami, S.

2018-02-01

Magneto-electroluminescence (MEL) effects are observed in single-layer organic light-emitting devices (OLEDs) comprising only macrocyclic aromatic hydrocarbons (MAHs). The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6). The MEL ratio of the resulting OLED is 1%-2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (-1.5% to -2%) in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

Efficient blue-green and green electroluminescent devices obtained by doping iridium complexes into hole-block material as supplementary light-emitting layer

Energy Technology Data Exchange (ETDEWEB)

Zhou, Liang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zheng, Youxuan, E-mail: yxzheng@mail.nju.edu.cn [State Key Laboratory of Coordination Chemistry, Nanjing National Laboratory of Microstructures, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China); Deng, Ruiping; Feng, Jing; Song, Mingxing; Hao, Zhaomin [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zhang, Hongjie, E-mail: hongjie@ciac.jl.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zuo, Jinglin; You, Xiaozeng [State Key Laboratory of Coordination Chemistry, Nanjing National Laboratory of Microstructures, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China)

2014-04-15

In this work, organic electroluminescent (EL) devices with dominant and supplementary light-emitting layers (EMLs) were designed to further improve the EL performances of two iridium{sup III}-based phosphorescent complexes, which have been reported to provide EL devices with slow EL efficiency roll-off. The widely used hole-block material 2,2′,2''-(1,3,5-Benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) was selected as host material to construct the supplementary EML. Compared with single-EML devices, double-EMLs devices showed higher EL efficiencies, higher brightness, and lower operation voltage attributed to wider recombination zone and better balance of carriers. In addition, the insertion of supplementary EML is instrumental in facilitating carriers trapping, thus improving the color purity. Finally, high performance blue-green and green EL devices with maximum current efficiencies of 35.22 and 90.68 cd/A, maximum power efficiencies of 26.36 and 98.18 lm/W, and maximum brightness of 56,678 and 112,352 cd/m{sup 2}, respectively, were obtained by optimizing the doping concentrations. Such a device design strategy extends the application of a double EML device structure and provides a chance to simplify device fabrication processes. -- Highlights: • Electroluminescent devices with supplementary light-emitting layer were fabricated. • Doping concentrations and thicknesses were optimized. • Better balance of holes and electrons causes the enhanced efficiency. • Improved carrier trapping suppresses the emission of host material.

Correlation of AlGaN/GaN high-electron-mobility transistors electroluminescence characteristics with current collapse

Science.gov (United States)

Ohi, Shintaro; Yamazaki, Taisei; Asubar, Joel T.; Tokuda, Hirokuni; Kuzuhara, Masaaki

2018-02-01

We report on the correlation between the electroluminescence and current collapse of AlGaN/GaN high-electron-mobility transistors (HEMTs). Standard passivated devices suffering from severe current collapse exhibited high-intensity whitish electroluminescence confined near the drain contact. In contrast, devices with reduced current collapse resulting from oxygen plasma treatment or GaN capping showed low-intensity reddish emission across the entire gate-drain access region. A qualitative explanation of this observed correlation between the current collapse and electroluminescence is presented. Our results demonstrate that electroluminescence analysis is a powerful tool not only for identifying high-field regions but also for assessing the degree of current collapse in AlGaN/GaN HEMTs.

AC Electroluminescent Processes in Pr3+-Activated (Ba0.4Ca0.6TiO3 Diphase Polycrystals

Directory of Open Access Journals (Sweden)

Nan Gao

2017-05-01

Full Text Available We investigated the properties of alternating current (AC-driven electroluminescence from (Ba0.4Ca0.6TiO3:Pr3+ diphase polycrystal-based device. The results of crystal phases and micrographs, and the symmetrical dual emissions in one AC cycle, indicate the spontaneous formation of a dielectric/phosphor/dielectric sandwich microstructure in (Ba0.4Ca0.6TiO3:Pr3+. The electroluminescent device emits a red light of 617 nm, which is attributed to the 1D2-3H4 transition of Pr3+ in the phosphor phase. At a fixed AC frequency, the intensity of electroluminescence exhibits a steep enhancement when applying an increased driving electric field that is beyond a threshold. In a fixed driving electric field, the intensity of electroluminescence shows a rapid rise at low frequencies, but reaches saturation at high frequencies. Based on a double-injection model, we discussed systematically the electroluminescent processes in a whole cycle of AC electric field, which matched well with the experimental data. Our investigation is expected to expand our understanding of such a diphase electroluminescent device, thereby promoting their applications in lighting and displays.

Ultraviolet-visible electroluminescence from metal-oxide-semiconductor devices with CeO2 films on silicon

International Nuclear Information System (INIS)

Lv, Chunyan; Zhu, Chen; Wang, Canxing; Li, Dongsheng; Ma, Xiangyang; Yang, Deren

2015-01-01

We report on ultraviolet-visible (UV-Vis) electroluminescence (EL) from metal-oxide-semiconductor (MOS) devices with the CeO 2 films annealed at low temperatures. At the same injection current, the UV-Vis EL from the MOS device with the 550 °C-annealed CeO 2 film is much stronger than that from the counterpart with the 450 °C-annealed CeO 2 film. This is due to that the 550 °C-annealed CeO 2 film contains more Ce 3+ ions and oxygen vacancies. It is tentatively proposed that the recombination of the electrons in multiple oxygen-vacancy–related energy levels with the holes in Ce 4f 1 energy band pertaining to Ce 3+ ions leads to the UV-Vis EL

Thermo-optical properties of 1H[3,4-b] quinoline films used in electroluminescent devices

Science.gov (United States)

Jaglarz, Janusz; Kępińska, Mirosława; Sanetra, Jerzy

2014-06-01

Electroluminescence cells with H[3,4-b] quinoline layers are promising devices for a blue light emitting EL diode. This work measured the optical reflectance as a function of temperature in copolymers PAQ layers deposited on Si crystalline substrate. Using the extended Cauchy dispersion model of the film refractive index we determined the thermo-optical coefficients for quinoline layers in the temperature range of 76-333 K from combined ellipsometric and spectrofotometric studies. The obtained values of thermo-optical coefficients of thin PAQ film, were negative and ranged in 5-10 × 10-4 [1/K].

Organic solution-processible electroluminescent molecular glasses for non-doped standard red OLEDs with electrically stable chromaticity

Energy Technology Data Exchange (ETDEWEB)

Bi, Xiaoman; Zuo, Weiwei; Liu, Yingliang, E-mail: liuylxn@sohu.com; Zhang, Zhenru; Zeng, Cen; Xu, Shengang; Cao, Shaokui, E-mail: caoshaokui@zzu.edu.cn

2015-10-15

Highlights: • The D–A–D electroluminescent molecular glasses are synthesized. • Non-doped red electroluminescent film is fabricated by spin-coating. • Red OLED shows stable wavelength, luminous efficiency and chromaticity. • CIE1931 coordinate is in accord with standard red light in PAL system. - Abstract: Organic light-emitting molecular glasses (OEMGs) are synthesized through the introduction of nonplanar donor and branched aliphatic chain into electroluminescent emitters. The target OEMGs are characterized by {sup 1}H NMR, {sup 13}C NMR, IR, UV–vis and fluorescent spectra as well as elemental analysis, TG and DSC. The results indicated that the optical, electrochemical and electroluminescent properties of OEMGs are adjusted successfully by the replacement of electron-donating group. The non-doped OLED device with a standard red electroluminescent emission is achieved by spin-coating the THF solution of OEMG with a triphenylamine moiety. This non-doped red OLED device takes on an electrically stable electroluminescent performance, including the stable maximum electroluminescent wavelength of 640 nm, the stable luminous efficiency of 2.4 cd/A and the stable CIE1931 coordinate of (x, y) = (0.64, 0.35), which is basically in accord with the CIE1931 coordinate (x, y) = (0.64, 0.33) of standard red light in PAL system.

Novel Mechano-Luminescent Sensors Based on Piezoelectric/Electroluminescent Composites

Directory of Open Access Journals (Sweden)

Yunzhang Fang

2011-04-01

Full Text Available A high-sensitivity mechano-luminescent sensor was fabricated on the basis of piezoelectric/electroluminescent composites. The working principle of this mechano-luminescent sensor was elucidated by analyzing the relationship between the piezoelectric-induced charges and the electroluminescent effects. When a stress is applied on the piezoelectric layer, electrical charges will be induced at both the top and bottom sides of the piezoelectric layer. The induced electrical charges will lead to a light output from the electroluminescent layer, thus producing a mechano-luminescence effect. By increasing the vibration strength or frequency applied, the mechano-luminescence output can be obviously enhanced. Mechano-luminescence sensors have potential in smart stress-to-light devices, such as foot-stress-distribution-diagnosis systems and dynamic-load-monitors for bridge hanging cables.

Room-temperature low-voltage electroluminescence in amorphous carbon nitride thin films

Science.gov (United States)

Reyes, R.; Legnani, C.; Ribeiro Pinto, P. M.; Cremona, M.; de Araújo, P. J. G.; Achete, C. A.

2003-06-01

White-blue electroluminescent emission with a voltage bias less than 10 V was achieved in rf sputter-deposited amorphous carbon nitride (a-CN) and amorphous silicon carbon nitride (a-SiCN) thin-film-based devices. The heterojunction structures of these devices consist of: Indium tin oxide (ITO), used as a transparent anode; amorphous carbon film as an emission layer, and aluminum as a cathode. The thickness of the carbon films was about 250 Å. In all of the produced diodes, a stable visible emission peaked around 475 nm is observed at room temperature and the emission intensity increases with the current density. For an applied voltage of 14 V, the luminance was about 3 mCd/m2. The electroluminescent properties of the two devices are discussed and compared.

Spray deposition of organic electroluminescent coatings for application in flexible light emitting devices

Directory of Open Access Journals (Sweden)

Mariya Aleksandrova

2015-12-01

Full Text Available Organic electroluminescent (EL films of tris(8-hydroxyquinolinatoaluminum (Alq3 mixed with polystyrene (PS binder were produced by spray deposition. The influence of the substrate temperature on the layer’s morphology and uniformity was investigated. The deposition conditions were optimized and simple flexible light-emitting devices consisting of indium-tin oxide/Alq3:PS/aluminum were fabricated on polyethylene terephthalate (PET foil to demonstrate the advantages of the sprayed organic coatings. Same structure was produced by thermal evaporation of Alq3 film as a reference. The influence of the deposition method on the film roughness and contact resistance at the electrode interfaces for both types of structures was estimated. The results were related to the devices’ efficiency. It was found that the samples with sprayed films turn on at 4 V, which is 2 V lower in comparison to the device with thermal evaporated Alq3. The current through the sprayed device is six times higher as well (17 mA vs. 2.8 mA at 6.5 V, which can be ascribed to the lower contact resistance at the EL film/electrode interfaces. This is due to the lower surface roughness of the pulverized layers.

Electroluminescence from a diamond device with ion-beam-micromachined buried graphitic electrodes

Energy Technology Data Exchange (ETDEWEB)

Forneris, J., E-mail: jacopo.forneris@unito.it [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Battiato, A.; Gatto Monticone, D. [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Picollo, F. [Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Amato, G.; Boarino, L.; Brida, G.; Degiovanni, I.P.; Enrico, E.; Genovese, M.; Moreva, E.; Traina, P. [Istituto Nazionale di Ricerca Metrologica (INRiM), Torino (Italy); Verona, C.; Verona Rinati, G. [Department of Industrial Engineering, University of Roma “Tor Vergata”, Roma (Italy); Olivero, P. [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy)

2015-04-01

Focused MeV ion microbeams are suitable tools for the direct writing of conductive graphitic channels buried in an insulating diamond bulk, as demonstrated in previous works with the fabrication of multi-electrode ionizing radiation detectors and cellular biosensors. In this work we investigate the suitability of the fabrication method for the electrical excitation of color centers in diamond. Differently from photoluminescence, electroluminescence requires an electrical current flowing through the diamond sub-gap states for the excitation of the color centers. With this purpose, buried graphitic electrodes with a spacing of 10 μm were fabricated in the bulk of a detector-grade CVD single-crystal diamond sample using a scanning 1.8 MeV He{sup +} micro-beam. The current flowing in the gap region between the electrodes upon the application of a 450 V bias voltage was exploited as the excitation pump for the electroluminescence of different types of color centers localized in the above-mentioned gap. The bright light emission was spatially mapped using a confocal optical microscopy setup. The spectral analysis of electroluminescence revealed the emission from neutrally-charged nitrogen-vacancy centers (NV{sup 0}, λ{sub ZPL} = 575 nm), as well as from cluster crystal dislocations (A-band, λ = 400–500 nm). Moreover, an electroluminescence signal with appealing spectral features (sharp emission at room temperature, low phonon sidebands) from He-related defects was detected (λ{sub ZPL} = 536.3 nm, λ{sub ZPL} = 560.5 nm); a low and broad peak around λ = 740 nm was also observed and tentatively ascribed to Si-V or GR1 centers. These results pose interesting future perspectives for the fabrication of electrically-stimulated single-photon emitters in diamond for applications in quantum optics and quantum cryptography.

Zinc Cadmium Selenide Cladded Quantum Dot Based Electroluminescent and Nonvolatile Memory Devices

Science.gov (United States)

Al-Amody, Fuad H.

This dissertation presents electroluminescent (EL) and nonvolatile memory devices fabricated using pseudomorphic ZnCdSe-based cladded quantum dots (QDs). These dots were grown using our own in-school built novel reactor. The EL device was fabricated on a substrate of ITO (indium tin oxide) coated glass with the quantum dots sandwiched between anode and cathode contacts with a small barrier layer on top of the QDs. The importance of these cladded dots is to increase the quantum yield of device. This device is unique as they utilize quantum dots that are pseudomorphic (nearly lattice-matched core and the shell of the dot). In the case of floating quantum dot gate nonvolatile memory, cladded ZnCdSe quantum dots are deposited on single crystalline gate insulator (ZnMgS/ZnMgSe), which is grown using metal-organic chemical vapor deposition (MOCVD). The control gate dielectric layer of the nonvolatile memory is Si3N4 or SiO2 and is grown using plasma enhanced chemical vapor deposition (PECVD). The cladded dots are grown using an improved methodology of photo-assisted microwave plasma metal-organic chemical vapor deposition (PMP-MOCVD) enhanced reactor. The cladding composition of the core and shell of the dots was engineered by the help of ultraviolet light which changed the incorporation of zinc (and hence composition of ZnCdSe). This makes ZnxCd1--xSe-ZnyCd1--y Se QDs to have a low composition of zinc in the core than the cladding (x

Organic Electroluminescent Sensor for Pressure Measurement

Directory of Open Access Journals (Sweden)

Tomohide Niimi

2012-10-01

Full Text Available We have proposed a novel concept of a pressure sensor called electroluminescent pressure sensor (ELPS based on oxygen quenching of electroluminescence. The sensor was fabricated as an organic light-emitting device (OLED with phosphorescent dyes whose phosphorescence can be quenched by oxygenmolecules, and with a polymer electrode which permeates oxygen molecules. The sensor was a single-layer OLED with Platinum (II octaethylporphine (PtOEP doped into poly(vinylcarbazole (PVK as an oxygen sensitive emissive layer and poly(3,4-ethylenedioxythiophene mixed with poly(styrenesulfonate (PEDOT:PSS as an oxygen permeating polymer anode. The pressure sensitivity of the fabricated ELPS sample was equivalent to that of the sensor excited by an illumination light source. Moreover, the pressure sensitivity of the sensor is equivalent to that of conventional pressure-sensitive paint (PSP, which is an optical pressure sensor based on photoluminescence.

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Science.gov (United States)

Gelloz, B.; Sano, H.; Boukherroub, R.; Wayner, D. D. M.; Lockwood, D. J.; Koshida, N.

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 °C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreatred devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device.

Direct Vapor Growth of Perovskite CsPbBr3 Nanoplate Electroluminescence Devices.

Science.gov (United States)

Hu, Xuelu; Zhou, Hong; Jiang, Zhenyu; Wang, Xiao; Yuan, Shuangping; Lan, Jianyue; Fu, Yongping; Zhang, Xuehong; Zheng, Weihao; Wang, Xiaoxia; Zhu, Xiaoli; Liao, Lei; Xu, Gengzhao; Jin, Song; Pan, Anlian

2017-10-24

Metal halide perovskite nanostructures hold great promises as nanoscale light sources for integrated photonics due to their excellent optoelectronic properties. However, it remains a great challenge to fabricate halide perovskite nanodevices using traditional lithographic methods because the halide perovskites can be dissolved in polar solvents that are required in the traditional device fabrication process. Herein, we report single CsPbBr 3 nanoplate electroluminescence (EL) devices fabricated by directly growing CsPbBr 3 nanoplates on prepatterned indium tin oxide (ITO) electrodes via a vapor-phase deposition. Bright EL occurs in the region near the negatively biased contact, with a turn-on voltage of ∼3 V, a narrow full width at half-maximum of 22 nm, and an external quantum efficiency of ∼0.2%. Moreover, through scanning photocurrent microscopy and surface electrostatic potential measurements, we found that the formation of ITO/p-type CsPbBr 3 Schottky barriers with highly efficient carrier injection is essential in realizing the EL. The formation of the ITO/p-type CsPbBr 3 Schottky diode is also confirmed by the corresponding transistor characteristics. The achievement of EL nanodevices enabled by directly grown perovskite nanostructures could find applications in on-chip integrated photonics circuits and systems.

Homogeneous Synthesis and Electroluminescence Device of Highly Luminescent CsPbBr3 Perovskite Nanocrystals.

Science.gov (United States)

Wei, Song; Yang, Yanchun; Kang, Xiaojiao; Wang, Lan; Huang, Lijian; Pan, Daocheng

2017-03-06

Highly luminescent CsPbBr 3 perovskite nanocrystals (PNCs) are homogeneously synthesized by mixing toluene solutions of PbBr 2 and cesium oleate at room temperature in open air. We found that PbBr 2 can be easily dissolved in nonpolar toluene in the presence of tetraoctylammonium bromide, which allows us to homogeneously prepare CsPbBr 3 perovskite quantum dots and prevents the use of harmful polar organic solvents, such as N,N-dimethylformamide, dimethyl sulfoxide, and N-methyl-2-pyrrolidone. Additionally, this method can be extended to synthesize highly luminescent CH 3 NH 3 PbBr 3 perovskite quantum dots. An electroluminescence device with a maximal luminance of 110 cd/m 2 has been fabricated by using high-quality CsPbBr 3 PNCs as the emitting layer.

Plasmonic enhancement of electroluminescence

Science.gov (United States)

Guzatov, D. V.; Gaponenko, S. V.; Demir, H. V.

2018-01-01

Here plasmonic effect specifically on electroluminescence (EL) is studied in terms of radiative and nonradiative decay rates for a dipole near a metal spherical nanoparticle (NP). Contribution from scattering is taken into account and is shown to play a decisive role in EL enhancement owing to pronounced size-dependent radiative decay enhancement and weak size effect on non-radiative counterpart. Unlike photoluminescence where local incident field factor mainly determines the enhancement possibility and level, EL enhancement is only possible by means of quantum yield rise, EL enhancement being feasible only for an intrinsic quantum yield Q0 red-orange range only. Independently of positive effect on quantum yield, metal nanoparticles embedded in an electroluminescent device will improve its efficiency at high currents owing to enhanced overall recombination rate which will diminish manifestation of Auger processes. The latter are believed to be responsible for the known undesirable efficiency droop in semiconductor commercial quantum well based LEDs at higher current. For the same reason plasmonics can diminish quantum dot photodegradation from Auger process induced non-radiative recombination and photoionization thus opening a way to avoid negative Auger effects in emerging colloidal semiconductor LEDs.

Electroluminescence and photosensitivity spectra of organic diode structures based on zinc complexes

Science.gov (United States)

Kaplunov, M. G.; Krasnikova, S. S.; Nikitenko, S. L.; Yakushchenko, I. K.

2017-01-01

Devices based on zinc complexes with sulphanylaminosubstituted ligands are characterized by dual function - electroluminescence (EL) and photosensitivity. Both EL and photosensitivity are associated with the formation of exciplexes.

Electroluminescence and photosensitivity spectra of organic diode structures based on zinc complexes

International Nuclear Information System (INIS)

Kaplunov, M.G.; Krasnikova, S.S.; Nikitenko, S.L.; Yakushchenko, I.K.

2017-01-01

Devices based on zinc complexes with sulphanylaminosubstituted ligands are characterized by dual function – electroluminescence (EL) and photosensitivity. Both EL and photosensitivity are associated with the formation of exciplexes.

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Energy Technology Data Exchange (ETDEWEB)

Gelloz, B.; Sano, H.; Koshida, N. [Dept. Elec. and Elec. Eng., Tokyo Univ. of A and T, Koganei, Tokyo 184-8588 (Japan); Boukherroub, R. [Laboratoire de Physique de la Matiere Condensee, Ecole Polytechnique, Route de Saclay, 91128 Palaiseau (France); Wayner, D.D.M.; Lockwood, D.J. [National Research Council, Ottawa (Canada)

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreated devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Bifunctional electroluminescent and photovoltaic devices using bathocuproine as electron-transporting material and an electron acceptor

International Nuclear Information System (INIS)

Chen, L.L.; Li, W.L.; Li, M.T.; Chu, B.

2007-01-01

Electroluminescence (EL) devices, using 4, 4',4''-tris (2-methylphenyl- phenylamino) triphenylamine (m-MTDATA) as hole-transporting material and bathocuproine (BCP) as an electron-transporting material, were fabricated, which emitted bright green light peaked at 520 nm instead of the emission of m-MTDATA or BCP. It was attributed to the exciplex formation and emission at the interface of m-MTDATA and BCP. EL performance was significantly enhanced by a thin mixed layer (5 nm) of m-MTDATA and BCP inserted between the two organic layers of the original m-MTDATA/BCP bilayer device. The trilayer device showed maximum luminance of 1,205 cd/m 2 at 8 V. At a luminance of 100 cd/m 2 , the power efficiency is 1.64 cd/A. Commission International De L'Eclairoge (CIE) color coordinates of the output spectrum of the devices at 8 V are x=0.244 and y=0.464. These devices also showed photovoltaic (PV) properties, which were sensitive to UV light. The PV diode exhibits high open-circuit voltage (V oc ) of 2.10 V under illumination of 365 nm UV light with 2 mW/cm 2 . And the short-circuit current (I sc ) of 92.5x10 -6 A/cm 2 , fill factor (FF) of 0.30 and power conversion efficiency (η e ) of 2.91% are respectively achieved. It is considered that strong exciplex emission in an EL device is a good indicator of efficient charge transfer at the organic interface, which is a basic requirement for good PV performance. Both the bilayer and trilayer devices showed EL and PV properties, suggesting their potential use as multifunction devices

Observation of near infrared and enhanced visible emissions from electroluminescent devices with organo samarium(III) complex

Energy Technology Data Exchange (ETDEWEB)

Chu, B [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, W L [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Hong, Z R [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Zang, F X [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wei, H Z [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wang, D Y [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, M T [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Lee, C S [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, S T [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)

2006-11-07

Samarium (dibenzoylmethanato){sub 3} bathophenanthroline (Sm(DBM){sub 3} bath) was employed as an emitting and electron transport layer in organic light emitting diodes (OLEDs), and narrow electroluminescent (EL) emissions of a Sm{sup 3+} ion were observed in the visible and near infrared (NIR) region, differing from those of the same devices with Eu{sup 3+}- or Tb{sup 3+}-complex EL devices with the same structure. The EL emissions of the Sm{sup 3+}-devices originate from transitions from {sup 4}G{sub 5/2} to the lower respective levels of Sm{sup 3+} ions. A maximum luminance of 490 cd m{sup -2} at 15 V and an EL efficiency of 0.6% at 0.17 mA cm{sup -2} were obtained in the visible region, and the improved efficiency should be attributed to introducing a transitional layer between the N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-diphenyl-4,4'-diamine (TPD) film and the Sm(DBM){sub 3} bath film and the avoidance of interfacial exciplex emission in devices. Sharp emissions of Sm{sup 3+} ions in the NIR region were also observed under a lower threshold value less than 4.5 V.

Extremely flexible, transparent, and strain-sensitive electroluminescent device based on ZnS:Cu-polyvinyl butyral composite and silver nanowires

Science.gov (United States)

Jun, Sungwoo; Kim, Youngmin; Ju, Byeong-Kwon; Kim, Jong-Woong

2018-01-01

A multifunctional alternate current electroluminescent device (ACEL) was achieved by compositing ZnS:Cu particles in polyvinyl butyral (PVB) with two layers of percolated silver nanowire (AgNW) electrodes. The strong hydrogen bonding interactions and entanglement of PVB chains considerably strengthened the PVB, and thus, the cured mixture of ZnS:Cu particles and freestanding PVB required no additional support. The device was fabricated by embedding AgNWs on both sides of the ZnS:Cu-PVB composite film using an inverted layer process and intense-pulsed-light treatment. The strong affinity of PVB to the polyvinyl pyrrolidone (PVP) layer, which capped the AgNWs, mechanically stabilized the device to such an extent that it could resist 10,000 bending cycles under a curvature radius of 500 μm. Using AgNW networks in both the top and bottom electrodes made a double-sided light-emitting device that could be applied to wearable lightings or flexible digital signage. The capacitance formed in the device sensitively varied with the applied bending and unfolding, thus demonstrating that the device can also be used as a deformation sensor.

Electroluminescence of colloidal ZnSe quantum dots

International Nuclear Information System (INIS)

Dey, S.C.; Nath, S.S.

2011-01-01

The article reports a green chemical synthesis of colloidal ZnSe quantum dots at a moderate temperature. The prepared colloid sample is characterised by UV-vis absorption spectroscopy and transmission electron microscopy. UV-vis spectroscopy reveals as-expected blue-shift with strong absorption edge at 400 nm and micrographs show a non-uniform size distribution of ZnSe quantum dots in the range 1-4 nm. Further, photoluminescence and electroluminescence spectroscopies are carried out to study optical emission. Each of the spectroscopies reveals two emission peaks, indicating band-to-band transition and defect related transition. From the luminescence studies, it can be inferred that the recombination of electrons and holes resulting from interband transition causes violet emission and the recombination of a photon generated hole with a charged state of Zn-vacancy gives blue emission. Meanwhile electroluminescence study suggests the application of ZnSe quantum dots as an efficient light emitting device with the advantage of colour tuning (violet-blue-violet). - Highlights: → Synthesis of ZnSe quantum dots by a green chemical route. → Characterisation: UV-vis absorption spectroscopy and transmission electron microscopy. → Analysis of UV-vis absorption spectrum and transmission electron micrographs. → Study of electro-optical properties by photoluminescence and electroluminescence. → Conclusion: ZnSe quantum dots can be used as LED with dual colour emission.

Bifunctional electroluminescent and photovoltaic devices using bathocuproine as electron-transporting material and an electron acceptor

Energy Technology Data Exchange (ETDEWEB)

Chen, L.L. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing, 100039 (China); Institute of Functional Material Chemistry, Faculty of Chemistry, Northeast Normal University, Changchun, 130024 (China); Li, W.L. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China)]. E-mail: wllioel@yahoo.com.cn; Li, M.T. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing, 100039 (China); Chu, B. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China)

2007-01-15

Electroluminescence (EL) devices, using 4, 4',4''-tris (2-methylphenyl- phenylamino) triphenylamine (m-MTDATA) as hole-transporting material and bathocuproine (BCP) as an electron-transporting material, were fabricated, which emitted bright green light peaked at 520 nm instead of the emission of m-MTDATA or BCP. It was attributed to the exciplex formation and emission at the interface of m-MTDATA and BCP. EL performance was significantly enhanced by a thin mixed layer (5 nm) of m-MTDATA and BCP inserted between the two organic layers of the original m-MTDATA/BCP bilayer device. The trilayer device showed maximum luminance of 1,205 cd/m{sup 2} at 8 V. At a luminance of 100 cd/m{sup 2}, the power efficiency is 1.64 cd/A. Commission International De L'Eclairoge (CIE) color coordinates of the output spectrum of the devices at 8 V are x=0.244 and y=0.464. These devices also showed photovoltaic (PV) properties, which were sensitive to UV light. The PV diode exhibits high open-circuit voltage (V {sub oc}) of 2.10 V under illumination of 365 nm UV light with 2 mW/cm{sup 2}. And the short-circuit current (I {sub sc}) of 92.5x10{sup -6} A/cm{sup 2}, fill factor (FF) of 0.30 and power conversion efficiency ({eta} {sub e}) of 2.91% are respectively achieved. It is considered that strong exciplex emission in an EL device is a good indicator of efficient charge transfer at the organic interface, which is a basic requirement for good PV performance. Both the bilayer and trilayer devices showed EL and PV properties, suggesting their potential use as multifunction devices.

Modelling electroluminescence in liquid argon

International Nuclear Information System (INIS)

Stewart, D Y; Barker, G J; Bennieston, A J; Harrison, P F; McConkey, N; Morgan, B; Ramachers, Y A; Lightfoot, P K; Robinson, M; Spooner, N J C; Thompson, L

2010-01-01

We present Monte-Carlo simulations of electron transport through liquid argon motivated by our recent observation of electroluminescence light emanating from a thick gaseous electron multiplier (THGEM) in a liquid argon volume. All known elastic and inelastic reaction cross-sections have been accounted for, providing electroluminescence light yield predictions for arbitrary electrostatic fields. This study concludes that the large field gradients needed to produce electroluminescence cannot be accounted for by straightforward electrostatic field calculations based on ideal THGEM holes, suggesting that further experimental investigations are required.

Electroluminescence light emitting diodes - an environmental friendly approach

International Nuclear Information System (INIS)

Shaukat, S.F.; Farooq, R.

2005-01-01

The simple porous silicon-based devices producing stable electroluminescence (EL) by the deposition of a poly-4-dicyanomethylene-4H-cyclopenta dithiophene monolayer (PCDM) into the nanostructure was reported. The structure of these devices is Au/PCDM/porous silicon/Si/Al. The EL emission is bright, visible by the naked eye under normal daylight and broad in wavelength covering the whole visible range with a peak at 60 nm. The emission area of the devices is 1 cm/sup 2/. The El starting voltage is in the range of 14-30 V and the current is around 300 mA. The time stability was good for all the devices tested. After exposure to the air for more than three months, the devices show nearly the same emission intensity without increase of external power supplied. (author)

Dye linked conjugated homopolymers: using conjugated polymer electroluminescence to optically pump porphyrin-dye emission

DEFF Research Database (Denmark)

Nielsen, K.T.; Spanggaard, H.; Krebs, Frederik C

2004-01-01

. Electroluminescent devices of the homopolymer itself and of the zinc-porphyrin containing polymer were prepared and the nature of the electroluminescence was characterized. The homopolymer segments were found to optically pump the emission of the zinc-porphyrin dye moities. The homopolymer exhibits blue......Zinc-porphyrin dye molecules were incorporated into the backbone of a conjugated polymer material by a method, which allowed for the incorporation of only one zinc-porphyrin dye molecule into the backbone of each conjugated polymer molecule. The electronic properties of the homopolymer were...

Electroluminescence property improvement by adjusting quantum wells’ position relative to p-doped region in InGaN/GaN multiple-quantum-well light emitting diodes

Directory of Open Access Journals (Sweden)

P. Chen

2017-03-01

Full Text Available The hole distribution and electroluminescence property improvement by adjusting the relative position between quantum wells and p-doped region in InGaN/GaN multiple-quantum-well structures are experimentally and theoretically investigated. Five designed samples with different barrier layer parameters of multiple-quantum-well structure are grown by MOCVD and then fabricated into devices. The electroluminescence properties of these samples are measured and compared. It is found that the output electroluminescence intensity of samples is enhanced if the position of quantum wells shifts towards p-side, while the output power is reduced if their position is shifted towards the n-side. The theoretical calculation of characteristics of these devices using the simulation program APSYS agrees well with the experimental data, illustrating that the effect of relative position between p-doped region and quantum wells on the improvement of hole distribution and electroluminescence performance is significant, especially for InGaN/GaN multiple-quantum-well devices operated under high injection condition.

Unusual near-white electroluminescence of light emitting diodes based on saddle-shaped porphyrins.

Science.gov (United States)

Shahroosvand, Hashem; Zakavi, Saeed; Sousaraei, Ahmad; Mohajerani, Ezeddin; Mahmoudi, Malek

2015-05-14

In contrast to the red electroluminescence emission frequently observed in porphyrins based OLED devices, the present devices exhibit a nearly white emission with greenish yellow, yellowish green and blue green hues in the case of Fe(II)(TCPPBr6) (TCPPBr6 = β-hexabromo-meso-tetrakis-(4-phenyl carboxyl) porphyrinato), Zn(II)(TPPBr6) and Co(II)(TPPBr6), respectively.

The effect of the thicknesses of the various layers on the colour emitted by an organic electroluminescent device

Science.gov (United States)

Jolinat, P.; Clergereaux, R.; Farenc, J.; Destruel, P.

1998-05-01

Organic electroluminescent diodes based on thin organic layers are one of the most promising next-generation systems for the backlighting of the liquid crystal screens. Among other methods to obtain white light, three-layer luminescent devices with each layer emitting one of the three fundamental colours have been studied here. Red, green and blue light were produced by 0022-3727/31/10/018/img1 doped with Nile red, 0022-3727/31/10/018/img1 and TPD layers respectively. A fourth thin film of TAZ has been inserted between TPD and 0022-3727/31/10/018/img1 to control injection of electrons into the TPD. The effect of the layers' thicknesses on the spectral emission of the device has been examined. Results show that the thicknesses of TAZ and doped 0022-3727/31/10/018/img1 layers have to be controlled to within a precision of better than 5 Å. The discussion turns on the possibility of applying this technology to screen backlighting.

Silicon nanowire hot carrier electroluminescence

Energy Technology Data Exchange (ETDEWEB)

Plessis, M. du, E-mail: monuko@up.ac.za; Joubert, T.-H.

2016-08-31

Avalanche electroluminescence from silicon pn junctions has been known for many years. However, the internal quantum efficiencies of these devices are quite low due to the indirect band gap nature of the semiconductor material. In this study we have used reach-through biasing and SOI (silicon-on-insulator) thin film structures to improve the internal power efficiency and the external light extraction efficiency. Both continuous silicon thin film pn junctions and parallel nanowire pn junctions were manufactured using a custom SOI technology. The pn junctions are operated in the reach-through mode of operation, thus increasing the average electric field within the fully depleted region. Experimental results of the emission spectrum indicate that the most dominant photon generating mechanism is due to intraband hot carrier relaxation processes. It was found that the SOI nanowire light source external power efficiency is at least an order of magnitude better than the comparable bulk CMOS (Complementary Metal Oxide Semiconductor) light source. - Highlights: • We investigate effect of electric field on silicon avalanche electroluminescence. • With reach-through pn junctions the current and carrier densities are kept constant. • Higher electric fields increase short wavelength radiation. • Higher electric fields decrease long wavelength radiation. • The effect of the electric field indicates intraband transitions as main mechanism.

Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq3

Science.gov (United States)

Yuan, Chao; Guan, Min; Zhang, Yang; Li, Yiyang; Liu, Shuangjie; Zeng, Yiping

2017-08-01

In this work, the organic light-emitting diodes (OLEDs) based on Alq3 are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage-luminescence (I-V-L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq3). The MoO3 injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO3 injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The Vf is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between Vf caused by the MoO3 injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy)3 is 0.73 us/K.

Carbon-electroluminescence: An organic approach to lighting

Science.gov (United States)

Kumari, Sonali; Chaudhary, Tarun; Chandran, Vivek; Lokeshwari, M.; Shastry, K.

2018-05-01

Over the recent years, quantum dots have garnered massive following and peaked in interest among the scientific community due to their versatility, exotic properties, ease of preparation and low cost. As the demand for faster, reliable and energy efficient electronic devices intensifies, extra emphasis is laid on the development of smart materials capable of satiating this need. Electroluminescent organic quantum dots have emerged as one of the prime contenders in addressing the ecological, economic and technological constraints. Application of such luminescent nanoparticles as fluorescent light converters in LEDs is touted as one of the reliable and easiest avenues in realizing and developing newer energy efficient technologies for the next millennia. One promising candidate is zig-zag graphene quantum dots, which exhibits high electro-luminescence due to a phenomenon known as quantum confinement (where size of the nano-particle is of the same order or less than that of Bohr exciton radius). In this paper, we aim to provide a review of past and present research in the synthesis and development of luminescence using organic quantum dots.

Electroluminescence from GaN-polymer heterojunction

International Nuclear Information System (INIS)

Chitara, Basant; Lal, Nidhi; Krupanidhi, S.B.; Rao, C.N.R.

2011-01-01

Inorganic and organic semiconductor devices are generally viewed as distinct and separate technologies. Herein we report a hybrid inorganic-organic light-emitting device employing the use of an air stable polymer, Poly (9,9-dioctylfluorene-alt-benzothiadiazole) as a p-type layer to create a heterojunction, avoiding the use of p-type GaN, which is difficult to grow, being prone to the complex and expensive fabrication techniques that characterises it. I-V characteristics of the GaN-polymer heterojunction fabricated by us exhibits excellent rectification. The luminescence onset voltage is typically about 8-10 V. The device emits yellowish white electroluminescence with CIE coordinates (0.42, 0.44). - Highlights: → We use a polymer Poly (9,9-dioctylfluorene-alt-benzothiadiazole) as a p-type layer to create a heterojunction. → I-V characteristics of the device fabricated by us exhibits excellent rectification. → The p-type polymer also emits yellow light, which when combined in proper composition with GaN, give rise to white light. → Device can be readily fabricated by just spin coating the polymer over GaN reducing the cost of the device.

Electroluminescence from single nanowires by tunnel injection: an experimental study

International Nuclear Information System (INIS)

Zimmler, Mariano A; Bao Jiming; Shalish, Ilan; Yi, Wei; Yoon, Joonah; Narayanamurti, Venkatesh; Capasso, Federico

2007-01-01

We present a hybrid light-emitting diode structure composed of an n-type gallium nitride nanowire on a p-type silicon substrate in which current is injected along the length of the nanowire. The device emits ultraviolet light under both bias polarities. Tunnel injection of holes from the p-type substrate (under forward bias) and from the metal (under reverse bias) through thin native oxide barriers consistently explains the observed electroluminescence behaviour. This work shows that the standard p-n junction model is generally not applicable to this kind of device structure

Synthesis and electroluminescent properties of blue emitting materials based on arylamine-substituted diphenylvinylbiphenyl derivatives for organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Kum Hee; You, Jae Nam; Won, Jiyeon; Lee, Jin Yong [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Seo, Ji Hoon [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@hongik.ac.kr [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2011-10-31

This paper reports the synthesis and electroluminescent properties of a series of blue emitting materials with arylamine and diphenylvinylbiphenyl groups for applications to efficient blue organic light-emitting diodes (OLEDs). All devices exhibited blue electroluminescence with electroluminescent properties that were quite sensitive to the structural features of the dopants in the emitting layers. In particular, the device using dopant 4 exhibited sky-blue emission with a maximum luminance, luminance efficiency, power efficiency, external quantum efficiency and CIE coordinates of 39,000 cd/m{sup 2}, 12.3 cd/A, 7.45 lm/W, 7.71% at 20 mA/cm{sup 2} and (x = 0.17, y = 0.31) at 8 V, respectively. In addition, a blue OLED using dopant 2 with CIE coordinates (x = 0.16, y = 0.18) at 8 V exhibited a luminous efficiency, power efficiency and external quantum efficiency of 4.39 cd/A, 2.46 lm/W and 2.97% at 20 mA/cm{sup 2}, respectively.

Study of various n-type organic semiconductors on ultraviolet detective and electroluminescent properties of optoelectronic integrated device

Science.gov (United States)

Deng, Chaoxu; Shao, Bingyao; Zhao, Dan; Zhou, Dianli; Yu, Junsheng

2017-11-01

Organic optoelectronic integrated device (OID) with both ultraviolet (UV) detective and electroluminescent (EL) properties was fabricated by using a thermally activated delayed fluorescence (TADF) semiconductor of (4s, 6s)-2,4,5,6-tetra(9H-carbazol-9-yl)isophthalonitrile (4CzIPN) as an emitter. The effect of five kinds of n-type organic semiconductors (OSCs) on the enhancement of UV detective and EL properties of OID was systematically studied. The result shows that two orders of magnitude in UV detectivity from 109 to 1011 Jones and 3.3 folds of luminance from 2499 to 8233 cd m-2 could be achieved. The result shows that not only the difference of lowest unoccupied molecular orbital (LUMO) between active layer and OSC but also the variety of electron mobility have a significant effect on the UV detective and EL performance through adjusting electron injection/transport. Additionally, the optimized OSC thickness is beneficial to confine the leaking of holes from the active layer to cathode, leading to the decrease of dark current for high detective performance. This work provides a useful method on broadening OSC material selection and device architecture construction for the realization of high performance OID.

The Electroluminescence Mechanism of Solution-Processed TADF Emitter 4CzIPN Doped OLEDs Investigated by Transient Measurements

Directory of Open Access Journals (Sweden)

Peng Wang

2016-10-01

Full Text Available High efficiency, solution-processed, organic light emitting devices (OLEDs, using a thermally-activated delayed fluorescent (TADF emitter, 1,2,3,5-tetrakis(carbazol-9-yl-4,6-dicyanobenzene (4CzIPN, are fabricated, and the transient electroluminescence (EL decay of the device with a structure of [ITO/PEDOT: PSS/4CzIPN 5 wt % doped 4,40-N,N0-dicarbazolylbiphenyl(CBP/bis-4,6-(3,5-di-4-pyridylphenyl-2-methylpyrimidine (B4PyMPM/lithium fluoride (LiF/Al], is systematically studied. The results shed light on the dominant operating mechanism in TADF-based OLEDs. Electroluminescence in the host–guest system is mainly produced from the 4CzIPN emitter, rather than the exciplex host materials.

Exciplex electroluminescence and photoluminescence spectra of the new organic materials based on zinc complexes of sulphanylamino-substituted ligands.

Science.gov (United States)

Kaplunov, Mikhail G; Krasnikova, Svetlana S; Nikitenko, Sergey L; Sermakasheva, Natalia L; Yakushchenko, Igor K

2012-04-03

We have investigated the electroluminescence spectra of the electroluminescent devices based on the new zinc complexes of amino-substituted benzothiazoles and quinolines containing the C-N-M-N chains in their chelate cycles. The spectra exhibit strong exciplex bands in the green to yellow region 540 to 590 nm due to interaction of the excited states of zinc complexes and triaryl molecules of the hole-transporting layer. For some devices, the intrinsic luminescence band of 460 nm in the blue region is also observed along with the exciplex band giving rise to an almost white color of the device emission. The exciplex band can be eliminated if the material of the hole-transporting layer is not a triarylamine derivative. We have also found the exciplex emission in the photoluminescence spectra of the films containing blends of zinc complex and triphenylamine material.

Green–white electroluminescence and green photoluminescence of zinc complexes

Energy Technology Data Exchange (ETDEWEB)

Janghouri, Mohammad; Mohajerani, Ezeddin [Laser and Plasma Research Institute, Shahid Beheshti University, G.C., Tehran 1983963113 (Iran, Islamic Republic of); Amini, Mostafa M.; Najafi, Ezzatollah [Department of Chemistry, Shahid Beheshti University, G.C., Tehran 1983963113 (Iran, Islamic Republic of)

2014-10-15

A series of zinc complexes has been synthesized and utilized as fluorescent materials in organic light-emitting diodes (OLEDs). All prepared complexes were characterized by elemental analysis (CHN), UV–vis, FT-IR and {sup 1}H NMR spectroscopy. The energy levels of zinc complexes were determined by cyclic voltammetry measurements. Devices with fundamental structure of ITO/PVK:PBD (50 nm)/zinc complexes/BCP (5 nm)/Alq{sub 3} (25 nm)/Al (180 nm) were fabricated. A green electroluminescence was obtained from thin film complexes at 25 nm thickness. When thickness of the complex bis(2-methylquinolin-8-olato)-bis[(acetato)-(methanol)zinc(II)] (B) in thin film decreased from 25 nm to 20, 18, and 12 nm, a white electroluminescence obtained. The white emission which was composed of blue and green attributed to the PVK:PBD blend and thickness of complex, respectively. With 12 nm thickness of complex, a maximum luminance of 4530 cd/m{sup 2} at a current density 398.32 mA/cm{sup 2} with CIE coordinates of 0.22 and 0.36 at 20 V was achieved. - Highlights: • Several new zinc complexes have been synthesized and utilized as fluorescent materials in OLEDs. • Photoluminescence emission of zinc complexes showed a red shift in respect to PVK:PBD blend. • Green electroluminescence emission from zinc complexes was achieved. • White emission has been obtained for an OLED by changing thickness of the zinc complex.

Green–white electroluminescence and green photoluminescence of zinc complexes

International Nuclear Information System (INIS)

Janghouri, Mohammad; Mohajerani, Ezeddin; Amini, Mostafa M.; Najafi, Ezzatollah

2014-01-01

A series of zinc complexes has been synthesized and utilized as fluorescent materials in organic light-emitting diodes (OLEDs). All prepared complexes were characterized by elemental analysis (CHN), UV–vis, FT-IR and 1 H NMR spectroscopy. The energy levels of zinc complexes were determined by cyclic voltammetry measurements. Devices with fundamental structure of ITO/PVK:PBD (50 nm)/zinc complexes/BCP (5 nm)/Alq 3 (25 nm)/Al (180 nm) were fabricated. A green electroluminescence was obtained from thin film complexes at 25 nm thickness. When thickness of the complex bis(2-methylquinolin-8-olato)-bis[(acetato)-(methanol)zinc(II)] (B) in thin film decreased from 25 nm to 20, 18, and 12 nm, a white electroluminescence obtained. The white emission which was composed of blue and green attributed to the PVK:PBD blend and thickness of complex, respectively. With 12 nm thickness of complex, a maximum luminance of 4530 cd/m 2 at a current density 398.32 mA/cm 2 with CIE coordinates of 0.22 and 0.36 at 20 V was achieved. - Highlights: • Several new zinc complexes have been synthesized and utilized as fluorescent materials in OLEDs. • Photoluminescence emission of zinc complexes showed a red shift in respect to PVK:PBD blend. • Green electroluminescence emission from zinc complexes was achieved. • White emission has been obtained for an OLED by changing thickness of the zinc complex

Modulation of the electroluminescence emission from ZnO/Si NCs/p-Si light-emitting devices via pulsed excitation

Science.gov (United States)

López-Vidrier, J.; Gutsch, S.; Blázquez, O.; Hiller, D.; Laube, J.; Kaur, R.; Hernández, S.; Garrido, B.; Zacharias, M.

2017-05-01

In this work, the electroluminescence (EL) emission of zinc oxide (ZnO)/Si nanocrystals (NCs)-based light-emitting devices was studied under pulsed electrical excitation. Both Si NCs and deep-level ZnO defects were found to contribute to the observed EL. Symmetric square voltage pulses (50-μs period) were found to notably enhance EL emission by about one order of magnitude. In addition, the control of the pulse parameters (accumulation and inversion times) was found to modify the emission lineshape, long inversion times (i.e., short accumulation times) suppressing ZnO defects contribution. The EL results were discussed in terms of the recombination dynamics taking place within the ZnO/Si NCs heterostructure, suggesting the excitation mechanism of the luminescent centers via a combination of electron impact, bipolar injection, and sequential carrier injection within their respective conduction regimes.

Electroluminescence Spectrum Shift with Switching Behaviour of Diamond Thin Films

Institute of Scientific and Technical Information of China (English)

王小平; 王丽军; 张启仁; 姚宁; 张兵临

2003-01-01

We report a special phenomenon on switching behaviour and the electroluminescence (EL) spectrum shift of doped diamond thin films. Nitrogen and cerium doped diamond thin films were deposited on a silicon substrate by microwave plasma-assisted chemical vapour deposition system and other special techniques. An EL device with a three-layer structure of nitrogen doped diamond/cerium doped diamond/SiO2 thin films was made. The EL device was driven by a direct-current power supply. Its EL character has been investigated, and a switching behaviour was observed. The EL light emission colour of diamond films changes from yellow (590nm) to blue (454 nm) while the switching behaviour appears.

Photoluminescence and electroluminescence of a tripodal compound containing 7-diethylamino-coumarin moiety

Energy Technology Data Exchange (ETDEWEB)

Yu Tianzhi; Zhang Peng; Zhang Hui; Meng Jing; Fan Duowang [Key Laboratory of Opto-Electronic Technology and Intelligent Control (Lanzhou Jiaotong University), Ministry of Education, Lanzhou 730070 (China); Zhao Yuling; Dong Wenkui [School of Chemical and Biological Engineering, Lanzhou Jiaotong University, Lanzhou 730070 (China)], E-mail: ytz823@hotmail.com

2008-12-07

A novel tripodal compound, tris[2-(7-diethylamino-coumarin-3-carboxamide)ethyl]amine (Tren-C), was synthesized and characterized by elemental analysis, infrared and {sup 1}H-NMR spectra. The photoluminescent (PL) and electroluminescent properties of Tren-C were investigated. Tren-C exhibits different colour emissions in solid states and solutions. The electroluminescence devices comprising vacuum vapour-deposited films using the compound as a dopant were fabricated, showing blue emissions that are identical to its PL spectrum in chloroform solutions. With the device structure of indium tin oxide (ITO)/4, 4', 4''-tris-N-naphthyl-N-phenylamino-triphenylamine (2-TNATA) (5 nm)/N, N'-bis-(naphthyl)-N, N'-diphenyl-1, 1'-biphenyl-4, 4'-diamine (NPB) (40 nm)/4, 4'-bis(9-carbazolyl) biphenyl (CBP) : Tren-C (0.5 wt%, 30 nm)/2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1, 3, 4-oxadiazole (Bu-PBD) (30 nm)/LiF (1 nm)/Al (100 nm), a maximum external quantum efficiency of 2.85%, a maximum luminous efficiency of 3.85 cd A{sup -1} and a maximum luminance of 1450 cd m{sup -2} are realized.

Broadband electroluminescence in fullerene crystals

International Nuclear Information System (INIS)

Werner, A.T.; Anders, J.; Byrne, H.J.; Maser, W.K.; Kaiser, M.; Mittelbach, A.; Roth, S.

1993-01-01

The observation of electroluminescence from crystalline fullerenes is described. A broad band emission spectrum, extending from 400nm to 1100nm is observed. The spectrum has a primary maximum at 920nm and a weaker feature centered on 420nm. The spectral characteristics are independent of the applied field and the longer wavelength region is identical to that measured in the high excitation density photoluminescence spectrum. In addition, the electroluminescence intensity increases with the cube of the injection current, strengthening the association to the nonlinear phenomena observed in the highly excited state of fullerenes. (orig.)

Electroluminescence of zinc oxide thin-films prepared via polymeric precursor and via sol-gel methods

International Nuclear Information System (INIS)

Lima, S.A.M.; Cremona, M.; Davolos, M.R.; Legnani, C.; Quirino, W.G.

2007-01-01

Zinc oxide (ZnO) is an electroluminescent (EL) material that can emit light in different regions of electromagnetic spectrum when electrically excited. Since ZnO is chemically stable, inexpensive and environmentally friendly material, its EL property can be useful to construct solid-state lamps for illumination or as UV emitter. We present here two wet chemical methods to prepare ZnO thin-films: the Pechini method and the sol-gel method, with both methods resulting in crystalline and transparent films with transmittance >85% at 550 nm. These films were used to make thin-film electroluminescent devices (TFELD) using two different insulator layers: lithium fluoride (LiF) or silica (SiO 2 ). All the devices exhibit at least two wide emission bands in the visible range centered at 420 nm and at 380 nm attributed to the electronic defects in the ZnO optical band gap. Besides these two bands, the device using SiO 2 and ZnO film obtained via sol-gel exhibits an additional band in the UV range centered at 350 nm which can be attributed to excitonic emission. These emission bands of ZnO can transfer their energy when a proper dopant is present. For the devices produced the voltage-current characteristics were measured in a specific range of applied voltage

Direct current electroluminescence in rare-earth-doped zinc sulphide

International Nuclear Information System (INIS)

Bryant, F.J.; Krier, A.

1984-01-01

Some of the properties and characteristics of rare-earth-doped zinc sulphide DCEL devices are reported. Two types of devices are discussed, co-evaporated ZnS:RE thin films and ion implanted ZnS:RE single crystal diodes. The thin film devices exhibit bright DCEL of various colours at low applied voltages (typically approximately 12 V). A study of the spectral intensities and lifetimes of the Er 3+ ion in ZnS:Er 3+ thin films is consistent with a Boltzmann energy distribution amongst the conduction electrons present in these devices. The ZnS:RE single crystal diodes fabricated in this laboratory by ion implantation are also capable of various colour DCEL. By comparing the EL emission obtained from the different rare earth dopants, erbium and neodymium are identified as the most efficient luminescence centres. Further consideration of the EL emission spectra gives evidence for the presence of inter-conduction band hot electron transitions in those devices containing rare earth dopants which are inefficent electroluminescence centres. These findings can be explained in terms of Auger processes occurring in rare earth complexes. (author)

High performance organic integrated device with ultraviolet photodetective and electroluminescent properties consisting of a charge-transfer-featured naphthalimide derivative

Energy Technology Data Exchange (ETDEWEB)

Wang, Hanyu; Wang, Xu; Yu, Junsheng, E-mail: luzhiyun@scu.edu.cn, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China, Chengdu 610054 (China); Zhou, Jie; Lu, Zhiyun, E-mail: luzhiyun@scu.edu.cn, E-mail: jsyu@uestc.edu.cn [College of Chemistry, Sichuan University, Chengdu 610064 (China)

2014-08-11

A high performance organic integrated device (OID) with ultraviolet photodetective and electroluminescent (EL) properties was fabricated by using a charge-transfer-featured naphthalimide derivative of 6-(3,5-bis-[9-(4-t-butylphenyl)-9H-carbazol-3-yl]-phenoxy)-2- (4-t-butylphenyl)-benzo[de]isoquinoline-1,3-dione (CzPhONI) as the active layer. The results showed that the OID had a high detectivity of 1.5 × 10{sup 11} Jones at −3 V under the UV-350 nm illumination with an intensity of 0.6 mW/cm{sup 2}, and yielded an exciplex EL light emission with a maximum brightness of 1437 cd/m{sup 2}. Based on the energy band diagram, both the charge transfer feature of CzPhONI and matched energy level alignment were responsible for the dual ultraviolet photodetective and EL functions of OID.

New electroluminescent carbazole-containing conjugated polymer: synthesis, photophysics, and electroluminescence

Czech Academy of Sciences Publication Activity Database

Cimrová, Věra; Ulbricht, C.; Dzhabarov, Vagif; Výprachtický, Drahomír; Egbe, D. A. M.

2014-01-01

Roč. 55, č. 24 (2014), s. 6220-6226 ISSN 0032-3861 R&D Projects: GA ČR GAP106/12/0827; GA ČR(CZ) GA13-26542S Institutional support: RVO:61389013 Keywords : carbazole-containing conjugated polymer * synthesis * photophysics and electroluminescence Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.562, year: 2014

Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Yuan, Chao [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Guan, Min, E-mail: guanmin@semi.ac.cn [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zhang, Yang [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Yiyang; Liu, Shuangjie [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zeng, Yiping [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China)

2017-08-15

Highlights: • The dependency relation between transmission rate and electron transport layer is revealed. • The critical temperature points for the influence of luminescent materials and injection barriers on delay time are found. • The influence of light-emitting material and injection layer on carrier accumulation is quantified. - Abstract: In this work, the organic light-emitting diodes (OLEDs) based on Alq{sub 3} are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage–luminescence (I–V–L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq{sub 3}). The MoO{sub 3} injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO{sub 3} injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The V{sub f} is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between V{sub f} caused by the MoO{sub 3} injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy){sub 3} is 0.73 us/K.

Observation of red electroluminescence from an Eu2O3/ p +-Si device and improved performance by introducing a Tb2O3 layer

International Nuclear Information System (INIS)

Yin, Xue; Wang, Shenwei; Mu, Guangyao; Wan, Guangmiao; Huang, Miaoling; Yi, Lixin

2017-01-01

We report red electroluminescence (EL) from an Eu 2 O 3 / p + -Si device with Eu 2 O 3 film annealed in oxygen ambient at 700 °C. The red EL is ascribed to the characteristic emissions of Eu 3+ ions in Eu 2 O 3 film and the luminescence mechanism is discussed in detail. In order to optimize the device performance, Eu 2 O 3 /Tb 2 O 3 multiple films were deposited on Si wafer, and the result showed EL intensity of the device was obviously enhanced and the turn-on voltage was reduced to about 10 V. Moreover, intensity ratio I ( 5 D 0 – 7 F 2 )/ I ( 5 D 0 – 7 F 1 ) was also significantly increased with the hypersensitive transition 5 D 0 – 7 F 2 as the most prominent group at about 611 nm. The improved performance was attributed to the added Tb 2 O 3 film that it can be served as the hole-injection layer to afford extra holes injected into the Eu 2 O 3 layer. (paper)

Spectroscopy and Device Performance of Rare Earth Doped III-Nitrides

National Research Council Canada - National Science Library

Hommerich, Uwe

2002-01-01

.... Prime candidates for redgreen- blue (RGB) emission are the rare earth ions Eu3+ (red), Er3+ (green), and Tm3+ (blue). A full-color TFEL phosphor system based on RE doped GaN has been demonstrated with high brightness...

Core-Shell Zn x Cd1- x Se/Zn y Cd1- y Se Quantum Dots for Nonvolatile Memory and Electroluminescent Device Applications

Science.gov (United States)

Al-Amoody, Fuad; Suarez, Ernesto; Rodriguez, Angel; Heller, E.; Huang, Wenli; Jain, F.

2011-08-01

This paper presents a floating quantum dot (QD) gate nonvolatile memory device using high-energy-gap Zn y Cd1- y Se-cladded Zn x Cd1- x Se quantum dots ( y > x) with tunneling layers comprising nearly lattice-matched semiconductors (e.g., ZnS/ZnMgS) on Si channels. Also presented is the fabrication of an electroluminescent (EL) device with embedded cladded ZnCdSe quantum dots. These ZnCdSe quantum dots were embedded between indium tin oxide (ITO) on glass and a top Schottky metal electrode deposited on a thin CsF barrier. These QDs, which were nucleated in a photo-assisted microwave plasma (PMP) metalorganic chemical vapor deposition (MOCVD) reactor, were grown between the source and drain regions on a p-type silicon substrate of the nonvolatile memory device. The composition of QD cladding, which relates to the value of y in Zn y Cd1- y Se, was engineered by the intensity of ultraviolet light, which controlled the incorporation of zinc in ZnCdSe. The QD quality is comparable to those deposited by other methods. Characteristics and modeling of the II-VI quantum dots as well as two diverse types of devices are presented in this paper.

Electroluminescence spectra of an STM-tip-induced quantum dot

NARCIS (Netherlands)

Croitoru, M.D.; Gladilin, V.N.; Fomin, V.; Devreese, J.T.; Kemerink, M.; Koenraad, P.M.; Sauthoff, K.; Wolter, J.H.; Long, A.R.; Davies, J.H.

2003-01-01

We analyse the electroluminescence measurements performed on a STM-tipImduced quantum dot in a GaAs layer. Positions of electroluminescence peaks, attributed to the electron-hole recombination in the quantum dot, are very sensitive to the electron tunnelling current even in the case when the current

Electroluminescence of Zn{sub 2}GeO{sub 4}:Mn through SiC whisker electric field enhancement

Energy Technology Data Exchange (ETDEWEB)

Wagstaff, Brandon, E-mail: wagstabj@mcmaster.ca [McMaster University, Department of Engineering Physics, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada); Kitai, Adrian, E-mail: kitaia@mcmaster.ca [McMaster University, Department of Engineering Physics, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada); McMaster University, Department of Materials Science and Engineering, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada)

2015-11-15

Alternating current (AC) electroluminescence of thin film oxide phosphors is well known. However in this work electroluminescence of bulk oxide powder phosphors is achieved. A new type of AC Electroluminescent (ACEL) device has been created and developed by integrating SiC whiskers into a phosphor matrix composed of manganese-activated zinc germanate (Zn{sub 2}GeO{sub 4}:Mn{sup 2+}). The conductive SiC whiskers enhance the average electric field in specific regions of the phosphor such that localized breakdown of the phosphor occurs, thus emitting green light. This field enhancement allows light emission to occur in thick film oxide powder phosphors and is notably the first time that bright and reasonably efficient electroluminescence of zinc germanate has been observed without using expensive thin film deposition techniques. Light emission has been achieved in thick pressed pellets using surface-deposited electrodes and the brightness-voltage characteristics of light emission are shown to be consistent with field emission of carriers from the embedded whiskers. - Highlights: • A new electroluminescent phosphor, Zn{sub 2}GeO{sub 4}Mn{sup 2+}+SiC whiskers, is proposed. • A procedure is described to fabricate a solid sample of this composite material. • Under an AC voltage, green light is emitted only in samples containing the SiC whiskers. • A brightness of 25 Cd/m{sup 2} and efficiency of 0.25 Lm/W is observed 9.6×10{sup 6} V/m. • This is notably the first time that ACEL has been observed in bulk Zn{sub 2}GeO{sub 4}Mn{sup 2+}.

Palladium-based on-wafer electroluminescence studies of GaN-based LED structures

Energy Technology Data Exchange (ETDEWEB)

Salcianu, C.O.; Thrush, E.J.; Humphreys, C.J. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Plumb, R.G. [Centre for Photonic Systems, Department of Engineering, University of Cambridge, Cambridge CB3 0FD (United Kingdom); Boyd, A.R.; Rockenfeller, O.; Schmitz, D.; Heuken, M. [AIXTRON AG, Kackertstr. 15-17, 52072 Aachen (Germany)

2008-07-01

Electroluminescence (EL) testing of Light Emitting Diode (LED) structures is usually done at the chip level. Assessing the optical and electrical properties of LED structures at the wafer scale prior to their processing would improve the cost effectiveness of producing LED-lamps. A non-destructive method for studying the luminescence properties of the structure at the wafer-scale is photoluminescence (PL). However, the relationship between the on-wafer PL data and the final device EL can be less than straightforward (Y. H Aliyu et al., Meas. Sci. Technol. 8, 437 (1997)) as the two techniques employ different carrier injection mechanisms. This paper provides an overview of some different techniques in which palladium is used as a contact in order to obtain on-wafer electroluminescence information which could be used to screen wafers prior to processing into final devices. Quick mapping of the electrical and optical characteristics was performed using either palladium needle electrodes directly, or using the latter in conjunction with evaporated palladium contacts to inject both electrons and holes into the active region via the p-type capping layer of the structure. For comparison, indium was also used to make contact to the n-layer so that electrons could be directly injected into that layer. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Transient electroluminescence on pristine and degraded phosphorescent blue OLEDs

Science.gov (United States)

Niu, Quan; Blom, Paul W. M.; May, Falk; Heimel, Paul; Zhang, Minlu; Eickhoff, Christian; Heinemeyer, Ute; Lennartz, Christian; Crǎciun, N. Irina

2017-11-01

In state-of-the-art blue phosphorescent organic light-emitting diode (PHOLED) device architectures, electrons and holes are injected into the emissive layer, where they are carried by the emitting and hole transporting units, respectively. Using transient electroluminescence measurements, we disentangle the contribution of the electrons and holes on the transport and efficiency of both pristine and degraded PHOLEDs. By varying the concentration of hole transporting units, we show that for pristine PHOLEDs, the transport is electron dominated. Furthermore, degradation of the PHOLEDs upon electrical aging is not related to the hole transport but is governed by a decrease in the electron transport due to the formation of electron traps.

Moisture exposure to different layers in organic light-emitting diodes and the effect on electroluminescence characteristics

International Nuclear Information System (INIS)

Liao, L. S.; Tang, C. W.

2008-01-01

Moisture effect on electroluminescence characteristics, including current density versus voltage, luminance versus voltage, luminous efficiency versus current density, dark spot formation, and operational stability of organic light-emitting diodes, has been systematically investigated by exposing each layer of the devices to moisture at room temperature. Moisture has a different effect on each of the interfaces or surfaces, and the influence increases as exposure time increases. There is a slight effect on the electroluminescence characteristics after the anode surface has been exposed to moisture. However, severe luminance decrease, dark spot formation, and operational stability degradation take place after the light-emitting layer or the electron-transporting layer is exposed to moisture. It is also demonstrated that the effect of moisture can be substantially reduced if the exposure to moisture is in a dark environment

A simulation toolkit for electroluminescence assessment in rare event experiments

CERN Document Server

Oliveira, C A B; Veenhof, R; Biagi, S; Monteiro, C M B; Santos, J M F dos; Ferreira, A L; Veloso, J F C A

2011-01-01

A good understanding of electroluminescence is a prerequisite when optimising double-phase noble gas detectors for Dark Matter searches and high-pressure xenon TPCs for neutrinoless double beta decay detection. A simulation toolkit for calculating the emission of light through electron impact on neon, argon, krypton and xenon has been developed using the Magboltz and Garfield programs. Calculated excitation and electroluminescence efficiencies, electroluminescence yield and associated statistical fluctuations are presented as a function of electric field. Good agreement with experiment and with Monte Carlo simulations has been obtained.

Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium activity in its 3rd year (Research and development of technologies for creating novel organic electroluminescent devices); 1999 nendo shin'yuki electroluminescence device no sosei gijutsu ni kansuru kenkyu kaihatsu seika hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Development is reported of an autoluminescent planar display and a free shape novel light source based on the technology of creating organic electroluminescent (EL) devices. A small dose of desiccant is added to an inorganic amorphous protecting film, and then high reliability is attained with the film staying in service for 30,000 hours or more. Technologies of ensuring uniform luminescence on a 100 times 100mm large screen and forming a 0.2mm pitch electrode pattern are established, and a 320 times 240 dot simple matrix display is developed. Novel red luminescent materials are developed, which are luminescent materials which incorporate Eu ions as luminescent seeds and exhibit a sharp luminescent spectrum, and novel organic materials. Novel blue luminescent materials are also developed. As for white luminescent materials, two types of novel pigments are developed. Studies are under way to apply amphoteric carrier transport materials to EL devices. A novel sealing technology is established which uses a composite material made of fine glass powder and UV setting resin. A SiON-based protecting film is successfully fabricated by which the internal stress is minimized. A technology is established of fabricating a diamond-like carbon (DLC) film for the protection of electrodes and wiring circuits. (NEDO)

Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium activity in its 3rd year (Research and development of technologies for creating novel organic electroluminescent devices); 1999 nendo shin'yuki electroluminescence device no sosei gijutsu ni kansuru kenkyu kaihatsu seika hokokusho. 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Development is reported of an autoluminescent planar display and a free shape novel light source based on the technology of creating organic electroluminescent (EL) devices. A small dose of desiccant is added to an inorganic amorphous protecting film, and then high reliability is attained with the film staying in service for 30,000 hours or more. Technologies of ensuring uniform luminescence on a 100 times 100mm large screen and forming a 0.2mm pitch electrode pattern are established, and a 320 times 240 dot simple matrix display is developed. Novel red luminescent materials are developed, which are luminescent materials which incorporate Eu ions as luminescent seeds and exhibit a sharp luminescent spectrum, and novel organic materials. Novel blue luminescent materials are also developed. As for white luminescent materials, two types of novel pigments are developed. Studies are under way to apply amphoteric carrier transport materials to EL devices. A novel sealing technology is established which uses a composite material made of fine glass powder and UV setting resin. A SiON-based protecting film is successfully fabricated by which the internal stress is minimized. A technology is established of fabricating a diamond-like carbon (DLC) film for the protection of electrodes and wiring circuits. (NEDO)

Comparison of electroluminescence intensity and photocurrent of polymer based solar cells

Energy Technology Data Exchange (ETDEWEB)

Hoyer, Ulrich; Swonke, Thomas; Auer, Richard [Bayerisches Zentrum fuer Angewandte Energieforschung e.V., Erlangen (Germany); Pinna, Luigi; Brabec, Christoph J. [Bayerisches Zentrum fuer Angewandte Energieforschung e.V., Erlangen (Germany); I-MEET, University Erlangen (Germany); Stubhan, Tobias; Li, Ning [I-MEET, University Erlangen (Germany)

2011-11-15

The reciprocity theorem for solar cell predicts a linear relation between electroluminescence emission and photovoltaic quantum efficiency and an exponential dependence of the electroluminescence signal on the applied voltage. Both dependencies are experimentally verified for polymer based solar cells in this paper. Furthermore it is shown, that electroluminescence imaging of organic solar cells has the potential to visualize the photocurrent distribution significantly faster than standard laser beam induced current mapping (LBIC) techniques. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Organic Light-Emitting Diodes Based on Phthalimide Derivatives: Improvement of the Electroluminescence Properties

Directory of Open Access Journals (Sweden)

Frédéric Dumur

2018-03-01

Full Text Available In this study, a phthalimide-based fluorescent material has been examined as a green emitter for multilayered organic light-emitting diodes (OLEDs. By optimizing the device stacking, a maximum brightness of 28,450 cd/m2 at 11.0 V and a maximum external quantum efficiency of 3.11% could be obtained. Interestingly, OLEDs fabricated with Fluo-2 presented a 20-fold current efficiency improvement compared to the previous results reported in the literature, evidencing the crucial role of the device stacking in the electroluminescence (EL performance of a selected emitter. Device lifetime was also examined and an operational stability comparable to that reported for a standard triplet emitter i.e., bis(4-methyl-2,5-diphenyl-pyridineiridium(III acetylacetonate [(mdppy2Iracac] was evidenced.

Low-threshold pure UV electroluminescence from n-ZnO:Al/i-layer/n-GaN heterojunction

International Nuclear Information System (INIS)

Li Songzhan; Fang Guojia; Long Hao; Wang Haoning; Huang Huihui; Mo Xiaoming; Zhao Xingzhong

2012-01-01

Ultraviolet (UV) electroluminescence (EL) of n-ZnO:Al (AZO)/i-layer/n-GaN heterojunctions with different intrinsic layers has been obtained. Rectifying behavior and EL spectra of the heterojunctions are investigated at room temperature. Under positive voltage, a dominant UV emission peak around ∼370 nm is observed for both AZO/i-ZnO/n-GaN and AZO/i-MgO/n-GaN heterojunctions. Nevertheless, the UV emission peak intensity of AZO/i-MgO/n-GaN heterojunction is much stronger than that of AZO/i-ZnO/n-GaN heterojunction at the same voltage. The threshold voltage of AZO/i-MgO/n-GaN heterostructured device is as low as 2.3 V. The difference of EL spectra and the emission mechanism in these devices are discussed. - Highlights: ► UV electroluminescence of n-ZnO:Al/i-layer/n-GaN heterojunctions has been obtained. ► Under positive voltage, a dominant UV emission peak around ∼370 nm is observed for both heterojunctions. ► The UV emission peak intensity of the heterojunction with i-MgO layer is much stronger than that with i-ZnO layer at the same voltage. ► The threshold voltage of n-ZnO:Al/i-MgO/n-GaN heterostructured device is as low as 2.3 V.

Encapsulation methods for organic electrical devices

Science.gov (United States)

Blum, Yigal D.; Chu, William Siu-Keung; MacQueen, David Brent; Shi, Yijian

2013-06-18

The disclosure provides methods and materials suitable for use as encapsulation barriers in electronic devices. In one embodiment, for example, there is provided an electroluminescent device or other electronic device encapsulated by alternating layers of a silicon-containing bonding material and a ceramic material. The encapsulation methods provide, for example, electronic devices with increased stability and shelf-life. The invention is useful, for example, in the field of microelectronic devices.

Electroluminescence Efficiency Enhancement using Metal Nanoparticles

National Research Council Canada - National Science Library

Soref, Richard A; Khurgin, J. B; Sun, G

2008-01-01

We apply the "effective mode volume" theory to evaluate enhancement of the electroluminescence efficiency of semiconductor emitters placed in the vicinity of isolated metal nanoparticles and their arrays...

Efficient light emitting devices based on phosphorescent partially doped emissive layers

KAUST Repository

Yang, Xiaohui; Jabbour, Ghassan E.

2013-01-01

We report efficient organic light emitting devices employing an ultrathin phosphor emissive layer. The electroluminescent spectra of these devices can be tuned by introducing a low-energy emitting phosphor layer into the emission zone. Devices

Electroluminescent properties of an electrochemically cross-linkable carbazole peripheral poly(benzyl ether) dendrimer.

Science.gov (United States)

Park, Jin Young; Kim, Dong-Eun; Ponnapati, Ramakrishna; Kim, Jong-Min; Kwon, Young-Soo; Advincula, Rigoberto C

2011-04-04

The electroluminescent (EL) properties of a cross-linkable carbazole-terminated poly(benzyl ether) dendrimer, G(3)-cbz DN, doped into a PVK:PBD host matrix with a double-layer device configuration are investigated. Different concentrations of the guest material can control device efficiency, related to chromaticity of white emission and the origin of excited-state complexes occurring between hole-transporting carbazole units (PVK or G(3)-cbz DN) and electron-transporting oxadiazole (PBD). Two excited states (exciplex and electroplex) generated at the interfaces of PVK/G(3)-cbz DN and PBD result in competitive emission, exhibiting a broad band in the EL spectra. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Functionalized organic semiconductor molecules to enhance charge carrier injection in electroluminescent cell

Science.gov (United States)

Yalcin, Eyyup; Kara, Duygu Akin; Karakaya, Caner; Yigit, Mesude Zeliha; Havare, Ali Kemal; Can, Mustafa; Tozlu, Cem; Demic, Serafettin; Kus, Mahmut; Aboulouard, Abdelkhalk

2017-07-01

Organic semiconductor (OSC) materials as a charge carrier interface play an important role to improve the device performance of organic electroluminescent cells. In this study, 4,4″-bis(diphenyl amino)-1,1':3‧,1″-terphenyl-5'-carboxylic acid (TPA) and 4,4″-di-9H-carbazol-9-yl-1,1':3‧,1″-terphenyl-5'-carboxylic acid (CAR) has been designed and synthesized to modify indium tin oxide (ITO) layer as interface. Bare ITO and PEDOT:PSS coated on ITO was used as reference anode electrodes for comparison. Furthermore, PEDOT:PSS coated over CAR/ITO and TPA/ITO to observe stability of OSC molecules and to completely cover the ITO surface. Electrical, optical and surface characterizations were performed for each device. Almost all modified devices showed around 36% decrease at the turn on voltage with respect to bare ITO. The current density of bare ITO, ITO/CAR and ITO/TPA were measured as 288, 1525 and 1869 A/m2, respectively. By increasing current density, luminance of modified devices showed much better performance with respect to unmodified devices.

Photoluminescence and electroluminescence from Ge/strained GeSn/Ge quantum wells

Energy Technology Data Exchange (ETDEWEB)

Lin, Chung-Yi; Chang, Chih-Chiang [Department of Electrical Engineering, Graduate Institute of Photonics and Optoelectronics, National Taiwan University, Taipei 10617, Taiwan (China); Huang, Chih-Hsiung; Huang, Shih-Hsien [Department of Electrical Engineering, Graduate Institute of Electronics Engineering, National Taiwan University, Taipei 10617, Taiwan (China); Liu, C. W., E-mail: chee@cc.ee.ntu.edu.tw [Department of Electrical Engineering, Graduate Institute of Photonics and Optoelectronics, National Taiwan University, Taipei 10617, Taiwan (China); Department of Electrical Engineering, Graduate Institute of Electronics Engineering, National Taiwan University, Taipei 10617, Taiwan (China); National Nano Device Labs, Hsinchu 30077, Taiwan (China); Huang, Yi-Chiau; Chung, Hua; Chang, Chorng-Ping [Applied Materials Inc., Sunnyvale, California 94085 (United States)

2016-08-29

Ge/strained GeSn/Ge quantum wells are grown on a 300 mm Si substrate by chemical vapor deposition. The direct bandgap emission from strained GeSn is observed in the photoluminescence spectra and is enhanced by Al{sub 2}O{sub 3}/SiO{sub 2} passivation due to the field effect. The electroluminescence of the direct bandgap emission of strained GeSn is also observed from the Ni/Al{sub 2}O{sub 3}/GeSn metal-insulator-semiconductor tunneling diodes. Electroluminescence is a good indicator of GeSn material quality, since defects in GeSn layers degrade the electroluminescence intensity significantly. At the accumulation bias, the holes in the Ni gate electrode tunnel to the strained n-type GeSn layer through the ultrathin Al{sub 2}O{sub 3} and recombine radiatively with electrons. The emission wavelength of photoluminescence and electroluminescence can be tuned by the Sn content.

Influence of surface wettability on cathode electroluminescence of porous silicon

International Nuclear Information System (INIS)

Goryachev, D.N.; Sreseli, O.M.; Belyakov, L.V.

1997-01-01

Influence of porous silicon wettability on efficiency of its cathode electroluminescence in electrolytes was investigated. It was revealed that increase of porous silicon wettability by electrolyte improved contact with a sublayer and provided generation of sufficient quantity of charge carriers. Diffusion - ionic, not electronic mechanism of charge transfer to the centers of micro crystallite electroluminescence is observed in porous silicon - electrolyte systems

Bidirectional electroluminescence from p-SnO2/i-MgZnO/n-ZnO heterojunction light-emitting diodes

International Nuclear Information System (INIS)

Yang, Yanqin; Li, Songzhan; Liu, Feng; Zhang, Nangang; Liu, Kan; Wang, Shengxiang; Fang, Guojia

2017-01-01

Light-emitting diodes based on p-SnO 2 /i-MgZnO/n-ZnO heterojunction have been fabricated. The material properties and the performance of heterojunction device are characterized. Current-voltage characteristics of the device show a diode-like rectifying behavior. Under forward bias, two prominent emission peaks located at 589 nm and 722 nm in the visible region and a weak ultraviolet emission are observed from p-SnO 2 /i-MgZnO/n-ZnO heterojunction device. As the device is under reverse bias, a broad visible emission band dominates the electroluminescence spectrum at a high current. Furthermore, the emission mechanism has been discussed in terms of energy band structures of the device under forward and reverse biases.

Ultraviolet electroluminescence from Au/MgO/MgxZn1−xO heterojunction diodes and the observation of Zn-rich cluster emission

International Nuclear Information System (INIS)

Liu, C.Y.; Xu, H.Y.; Sun, Y.; Zhang, C.; Ma, J.G.; Liu, Y.C.

2014-01-01

In this work, ultraviolet (UV) electroluminescence (EL) is achieved from Au/MgO/Mg x Zn 1−x O heterojunction diodes. The EL mechanism and laser forming process are discussed based on the energy band diagram, impact-ionization process and disordered optical structure. For ZnO and low Mg-content MgZnO devices, their EL spectra show single near-band-edge (NBE) emission. While in high Mg-content MgZnO devices, the emission from self-formed Zn-rich MgZnO clusters is observed and also contribute to the UV EL band. These Zn-rich clusters can act as thermally-stable luminescence centers, suggesting a promising route for developing MgZnO-based UV light-emitting devices. -- Highlights: • A series of Au/MgO/Mg x Zn 1−x O heterojunction diodes with multiple Mg compositions are fabricated and ultraviolet electroluminescence is achieved. • EL mechanism and laser forming process are discussed based on energy band diagram, impact-ionization process and disordered optical structure. • The transition from spontaneous to stimulated emission is observed in these heterojunctions, and the lasing mode is random laser. • In high Mg-content MgZnO devices, the emission from self-formed Zn-rich clusters is observed, which are thermally stable luminescence centers

Spectroscopic investigation of the interfaces in new poly(9,9-dihexyl–9H-fluorene-2,7- diyl based electroluminescent devices

Directory of Open Access Journals (Sweden)

C. Donitsi

2014-01-01

Full Text Available The highest occupied and lowest unoccupied states of the new electroluminescent material poly(9,9-dihexyl–9H- fluorene-2,7-diyl (PPV-D and polyvinylcarbazole (PVK are investigated using ultraviolet photoelectron and inverse photoemission spectroscopies. Hole injection barriers are determined for interfaces between indium-tin oxide covered substrates with work function ranging from 4.4 to 4.7 eV and these two polymers. Vacuum level alignment with flat bands away from the interface is found when the interface hole barrier is 0.6 eV or larger. Band bending away from the Fermi level occurs when the hole barrier is smaller than 0.6 eV. This is due to the accumulation charges at the interface with the polymer when the injection barrier is small. The resulting field bends the polymer levels to limit charge incoming in the bulk of the film. The efficiency of the electroluminescent structures is strongly influenced by the different energy levels alignment at the layer interfaces.

Effect of resonant tunneling on electroluminescence in nc-Si/SiO2 multilayers-based p-i-n structure

International Nuclear Information System (INIS)

Chen, D.Y.; Wang, Y.Y.; Sun, Y.; He, Y.J.; Zhang, G.

2015-01-01

P-i-n structures with SiO 2 /nc-Si/SiO 2 multilayers as intrinsic layer were prepared in conventional plasma enhanced chemical vapor deposition system. Their carrier transport and electroluminescence properties were investigated. Two resonant tunneling related current peaks with current dropping gradually under forward bias were observed in the current voltage curve. Non-uniformity of the interfaces might be responsible for the gradual dropping of the current. Electroluminescence intensity of the device under bias of 7 V which is near the resonant tunneling peak voltage of 7.2 V was weaker than that under 6.5 V. According to the Gaussian fitting results of the spectra, the intensity of the sub-peak of 650 nm originating from recombination of injected electrons and holes was decreased the most. When resonant tunneling conditions are met, it might be that most of the injected electrons participate in resonant tunneling and fewer in Pool–Frenkel tunneling, which is the main carrier transport mechanism, to contribute to electroluminescence intensity. - Highlights: • Two resonant tunneling peaks with current dropping gradually were observed. • The EL intensity of the structure under resonant tunneling peak voltage is weakened. • P–F tunneling is the main transport mechanism besides resonant tunneling

Study on electroluminescence processes in dye-doped organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Li Weizhi [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: leewz@uestc.edu.cn; Jiang Yadong; Wang Tao [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2008-07-15

Electroluminescence (EL) mechanism of dye-doped organic light-emitting diodes (OLEDs) was investigated by using three familiar fluorescent dyes, i.e., 5,12-Dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA), 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran(DCJTB), and 5,6,11,12-tetraphenylnaphthacene (Rubrene). EL spectra of the doped devices with structure of indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'- diamine (NPB) (40 nm)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3}) (x nm, x=0-40 nm)/dye: Alq{sub 3} (weight ratio{approx}1%, 2 nm)/Alq{sub 3} (48-x nm)/MgAg indicated that direct carrier trapping (DCT) process dominated light emission of devices. As a result, investigation of carrier-recombination site via doping, which is conventionally applied in OLEDs, is questionable since the doping site and the dopant itself may significantly influence the carrier-recombination process in the doped devices.

Bidirectional electroluminescence from p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Yang, Yanqin [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Li, Songzhan, E-mail: liszhan@whu.edu.cn [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Key Lab of Artificial Micro- and Nano-Structures of Ministry of Education of China, School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Liu, Feng; Zhang, Nangang; Liu, Kan [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Wang, Shengxiang, E-mail: sxwang@wtu.edu.cn [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Fang, Guojia [Key Lab of Artificial Micro- and Nano-Structures of Ministry of Education of China, School of Physics and Technology, Wuhan University, Wuhan 430072 (China)

2017-06-15

Light-emitting diodes based on p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction have been fabricated. The material properties and the performance of heterojunction device are characterized. Current-voltage characteristics of the device show a diode-like rectifying behavior. Under forward bias, two prominent emission peaks located at 589 nm and 722 nm in the visible region and a weak ultraviolet emission are observed from p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction device. As the device is under reverse bias, a broad visible emission band dominates the electroluminescence spectrum at a high current. Furthermore, the emission mechanism has been discussed in terms of energy band structures of the device under forward and reverse biases.

Co-deposition methods for the fabrication of organic optoelectronic devices

Science.gov (United States)

Thompson, Mark E.; Liu, Zhiwei; Wu, Chao

2016-09-06

A method for fabricating an OLED by preparing phosphorescent metal complexes in situ is provided. In particular, the method simultaneously synthesizes and deposits copper (I) complexes in an organic light emitting device. Devices comprising such complexes may provide improved photoluminescent and electroluminescent properties.

Spontaneous formation of {1 1-bar 0 1} InGaN quantum wells on a (1 1 2-bar 2) GaN template and their electroluminescence characteristics

International Nuclear Information System (INIS)

Masui, Hisashi; Kamber, Derrick S; Brinkley, Stuart E; Wu, Feng; Baker, Troy J; Zhong, Hong; Iza, Michael; Speck, James S; Nakamura, Shuji; DenBaars, Steven P

2010-01-01

Discrete dies of the light-emitting diode (LED) fabricated on a (1 1 2-bar 2)-oriented GaN template exhibited electroluminescence peaked at 467 nm and optical output power was greater than 200 µW at 20 mA. The LED was found to have quantum well structure grown on spontaneously formed {1 1-bar 0 1} facets, confirmed via transmission electron microscopy. Polarization switching was observed in luminescence perpendicular to the device surface: the dominant polarization was parallel to [1-bar 1-bar 2 3]. The device structure was shown to be advantageous for photovoltaic cell applications by evaluating photo-induced current, although piezoelectric effects on photocurrent were not explicitly determined. The filling rate of band-edge states was estimated to be 0.025 eV per decade of current via low-temperature electroluminescence measurements

Tunneling electron induced molecular electroluminescence from individual porphyrin J-aggregates

Energy Technology Data Exchange (ETDEWEB)

Meng, Qiushi; Zhang, Chao; Zhang, Yang, E-mail: zhyangnano@ustc.edu.cn, E-mail: zcdong@ustc.edu.cn; Zhang, Yao; Liao, Yuan; Dong, Zhenchao, E-mail: zhyangnano@ustc.edu.cn, E-mail: zcdong@ustc.edu.cn [Hefei National Laboratory for Physical Sciences at the Microscale and Synergetic Innovation Center of Quantum Information and Quantum Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2015-07-27

We investigate molecular electroluminescence from individual tubular porphyrin J-aggregates on Au(111) by tunneling electron excitations in an ultrahigh-vacuum scanning tunneling microscope (STM). High-resolution STM images suggest a spiral tubular structure for the porphyrin J-aggregate with highly ordered “brickwork”-like arrangements. Such aggregated nanotube is found to behave like a self-decoupled molecular architecture and shows red-shifted electroluminescence characteristics of J-aggregates originated from the delocalized excitons. The positions of the emission peaks are found to shift slightly depending on the excitation sites, which, together with the changes in the observed spectral profiles with vibronic progressions, suggest a limited exciton coherence number within several molecules. The J-aggregate electroluminescence is also found unipolar, occurring only at negative sample voltages, which is presumably related to the junction asymmetry in the context of molecular excitations via the carrier injection mechanism.

Coordination compounds of rare-earth metals with organic ligands for electroluminescent diodes

International Nuclear Information System (INIS)

Katkova, M A; Bochkarev, Mikhail N; Vitukhnovsky, Alexey G

2005-01-01

Data on lanthanide coordination compounds with organic ligands used in the design of electroluminescent diodes are summarised and systematically represented. The molecular and electronic structures and spectroscopic characteristics of these compounds are considered. A comparative analysis of the properties of organic electroluminescent diodes with different compositions of emitting and conductive layers is presented.

Achievement report for fiscal 1998. Research and development of technologies for creating new organic electroluminescent devices (2nd fiscal year); 1998 nendo seika hokokusho. Shin'yuki electronics ruminessensu device no sosei gijutsu ni kansuru kenkyu kaihatsu (dai 2 nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The aim of the efforts was to commercialize a multicolor, organic electroluminescent (EL) display and an energy efficient light source, to develop a highly efficient luminescent material, and to develop a protecting film for use in optical and electronic devices and technologies to seal the protecting film. Achievements in fiscal 1998 are mentioned below. The Kyushu office of Matsushita Electric Industrial Co., Ltd., manufactured a uniformly luminescent large screen, and Nisimu Electronic Industry Co., Ltd., fabricated a luminescent organic film by the wet method. As for materials, Dojindo mass-synthesized a hole transfer material, developed a new carrier transfer material, and developed a high-performance luminescent material. Daiden Co., Ltd., produced rare earth complexes and laminated pevskite. As for packaging technology, Shoei Chemical Co. developed a low-expansion glass filler, Kyushu University's Advanced Technology Joint Research Center formed an SiON protecting film on an EL device, and Fukuoka Mechanic and Electric Laboratory produced a DLC (diamond-like carbon) film. (NEDO)

Encapsulation methods and dielectric layers for organic electrical devices

Science.gov (United States)

Blum, Yigal D; Chu, William Siu-Keung; MacQueen, David Brent; Shi, Yijan

2013-07-02

The disclosure provides methods and materials suitable for use as encapsulation barriers and dielectric layers in electronic devices. In one embodiment, for example, there is provided an electroluminescent device or other electronic device with a dielectric layer comprising alternating layers of a silicon-containing bonding material and a ceramic material. The methods provide, for example, electronic devices with increased stability and shelf-life. The invention is useful, for example, in the field of microelectronic devices.

Electroluminescence and phototrigger effect in single crystals of GaSxSe1-x alloys

International Nuclear Information System (INIS)

Kyazym-Zade, A. G.; Salmanov, V. M.; Mokhtari, A. G.; Dadashova, V. V.; Agaeva, A. A.

2008-01-01

The effects of switching and electroluminescence as well as the interrelation between these effects in single crystals of GaS x Se 1-x alloys are detected and studied. It is established that the threshold voltage for switching depends on temperature, resistivity, and composition of alloys, and also on the intensity and spectrum of photoactive light. As a result, a phototrigger effect is observed; this effect arises under irradiation with light from the fundamental-absorption region. Electroluminescence is observed in the subthreshold region of the current-voltage characteristic; the electroluminescence intensity decreases drastically to zero as the sample is switched from a high-resistivity state to a low-resistivity state. Experimental data indicating that the electroluminescence and the switching effect are based on the injection mechanism (as it takes place in other layered crystals of the III-V type) are reported

Pulsed Electrical Spin Injection into InGaAs Quantum Dots: Studies of the Electroluminescence Polarization Dynamics

International Nuclear Information System (INIS)

Asshoff, P.; Loeffler, W.; Fluegge, H.; Zimmer, J.; Mueller, J.; Westenfelder, B.; Hu, D. Z.; Schaadt, D. M.; Kalt, H.; Hetterich, M.

2010-01-01

We present time-resolved studies of the spin polarization dynamics during and after initialization through pulsed electrical spin injection into InGaAs quantum dots embedded in a p-i-n-type spin-injection light-emitting diode. Experiments are performed with pulse widths in the nanosecond range and a time-resolved single photon counting setup is used to detect the subsequent electroluminescence. We find evidence that the achieved spin polarization shows an unexpected temporal behavior, attributed mainly to many-carrier and non-equilibrium effects in the device.

Hole-exciton interaction induced high field decay of magneto-electroluminescence in Alq3-based organic light-emitting diodes at room temperature

Science.gov (United States)

Zhang, Tingting; Holford, D. F.; Gu, Hang; Kreouzis, T.; Zhang, Sijie; Gillin, W. P.

2016-01-01

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq3) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq3 system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there is also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.

Enhancement of electroluminescence from embedded Si quantum dots/SiO2multilayers film by localized-surface-plasmon and surface roughening.

Science.gov (United States)

Li, Wei; Wang, Shaolei; Hu, Mingyue; He, Sufeng; Ge, Pengpeng; Wang, Jing; Guo, Yan Yan; Zhaowei, Liu

2015-07-03

In this paper, we prepared a novel structure to enhance the electroluminescence intensity from Si quantum dots/SiO2multilayers. An amorphous Si/SiO2 multilayer film was fabricated by plasma-enhanced chemical vapor deposition on a Pt nanoparticle (NP)-coated Si nanopillar array substrate. By thermal annealing, an embedded Si quantum dot (QDs)/SiO2 multilayer film was obtained. The result shows that electroluminescence intensity was significantly enhanced. And, the turn-on voltage of the luminescent device was reduced to 3 V. The enhancement of the light emission is due to the resonance coupling between the localized-surface-plasmon (LSP) of Pt NPs and the band-gap emission of Si QDs/SiO2 multilayers. The other factors were the improved absorption of excitation light and the increase of light extraction ratio by surface roughening structures. These excellent characteristics are promising for silicon-based light-emitting applications.

Double peak spectra in spontaneous edge electroluminescence

Czech Academy of Sciences Publication Activity Database

Zavadil, Jiří; Žďánský, Karel

1993-01-01

Roč. 36, č. 11 (1993), s. 1623-1632 ISSN 0038-1101 R&D Projects: GA AV ČR IAA167108 Keywords : light emitting diodes * electroluminescence * optical waveguide theory Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.871, year: 1993

Charge-trapping effect of doped fluorescent dye on the electroluminescent processes and its performance in polymer light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Ye Tengling; Chen Zhenyu; Chen Jiangshan [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, Changchun 130022 (China); Ma Dongge, E-mail: mdg1014@ciac.jl.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Graduate School of Chinese Academy of Sciences, Changchun 130022 (China)

2010-11-15

We have measured the temperature dependence of the steady-state current-voltage (I-V) characteristics and the transient electroluminescent (EL) characteristics in 4-(dicyanomethylene)-2-t-propyl-6-(1,1,7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) doped polyfluorene devices to study the charge-trapping effect of DCJTB fluorescent dye on luminescence processes and on device performance. Physical and chemical analyses prove that DCJTB molecules serve both as electron and hole traps, and the charge-trapping effect is more sensitive against the electrons than the holes at the low dopant concentration. This intrinsic characteristic causes the electron to be injected into the emitting layer first and then trapped in the bulk, producing a strong effect on device performance.

Hole-exciton interaction induced high field decay of magneto-electroluminescence in Alq{sub 3}-based organic light-emitting diodes at room temperature

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tingting; Holford, D. F.; Gu, Hang; Kreouzis, T. [Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Zhang, Sijie, E-mail: Sijie.zhang@scu.edu.cn, E-mail: w.gillin@qmul.ac.uk [College of Physical Science and Technology, Sichuan University, Chengdu 610064 (China); Gillin, W. P., E-mail: Sijie.zhang@scu.edu.cn, E-mail: w.gillin@qmul.ac.uk [Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); College of Physical Science and Technology, Sichuan University, Chengdu 610064 (China)

2016-01-11

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq{sub 3}) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq{sub 3} system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there is also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.

An IBM-Compatible 640 X 200 Electroluminescent (EL) Display Monitor

Science.gov (United States)

Gullick, Paul; Schmachtenberg, Richard; Laakso, Carl

1986-05-01

An electroluminescent flat-panel display has been developed and recently introduced that fills any of the needs of the portable computer market. The display is very thin, yet rugged enough for the rigors of portability. It is highly integrated, and very reliable. It has the crisp and clear display image that is typical of high quality electroluminescent displays. The unit has a pixel matrix organization and pixel dimensions that are not only asthetically and ergonomically pleasing, but also make the display compatible with the most widely used software packages run on today's personal computers (Figure 1).

Structural effects of a light emitting copolymer having perylene moieties in the side chain on the electroluminescent characteristics

International Nuclear Information System (INIS)

Lee, Chang Ho; Ryu, Seung Hoon; Jang, Hee Dong; Oh, Se Young

2004-01-01

We have synthesized a novel side chain light emitting copolymer. The side chain light emitting copolymer has a perylene moiety as an emitting unit and methylmethacrylate (MMA) as a spacer to decrease the concentration quenching of light emitting site in the polymer intrachain. These polymers are very soluble in most organic solvents such as monochlorobenzene, tetrahydrofuran, chloroform and benzene. The single-layered electroluminescent (EL) device consisting of ITO/carrier transporting copolymer and light emitting copolymer/Al was manufactured. The carrier transporting copolymer has triphenylamine moiety as a hole transporting unit and triazine moiety as an electron transporting unit in the polymer side chain. This device exhibits maximum external quantum efficiency when the MMA contents of light emitting copolymer is 30 wt.%. In particular, the device emits more blue light as MMA contents increase

ZnO nanorod based low turn-on voltage LEDs with wide electroluminescence spectra

International Nuclear Information System (INIS)

Jha, S.K.; Kutsay, O.; Bello, I.; Lee, S.T.

2013-01-01

Light emitting diodes (LEDs) based on arrays of n-type ZnO Nanorods were fabricated on p-GaN films using a hydrothermal method. The LEDs emit mainly in blue and UV range of the light. Their current–Voltage (I–V) characteristics typically show a low leakage current (7.2 μA) and a high rectification ratio (3 5 5). Devices operate at a low turn-on voltage of ∼4.5 V. Photoluminescence (PL) and electroluminescence (EL) measurements suggest low density of ZnO defects; however, in some aspects density of interfacial defects still might be considerable in the studied devices. The PL emission is deconvoluted to three peaks that are located at wavelengths of 361, 381, and 397 nm, while the wide EL spectra are deconvoluted to five peaks appearing at 368, 385, 427, 474, and 515 nm. Near-band-edge (NBE) emission of p-GaN and n-ZnO was observed in both the PL and EL spectra. Deconvoluted EL spectra consist of a very wide green band with the peak at 515 nm and extending up to 650 nm (red), and a rarely reported EL emission at 474 nm. Origin of these emissions is discussed, herein. The electrical characteristics together with EL characteristics indicate potential to develop and study p-GaN/n-ZnO nanorod LEDs for white emitting applications. - Highlights: ► A low turn-on voltage (4–4.5 V) and low threshold (5 V) electroluminescence from ZnO/GaN heterostructure. ► A wide spectrum EL emission (360–700 nm) suitable for white LED application. ► EL spectra consist of a rarely reported emission band with peak at 474 nm. ► Low-temperature and solution based fabrication, which is scalable and of low cost.

Synthesis and electroluminescence properties of europium (III) complexes with new second ligands

International Nuclear Information System (INIS)

Liu Ze; Wen Fushan; Li Wenlian

2005-01-01

Two novel second ligands, 9,9-Di-(4-methoxyphenyl)-9-H-4,5-' (OMe-Spiro-DF) and 9,9-Di-(2-(4-(4-butyloxy)phenyl)-5-phenyl-1,3,4-oxadiazolyl)-phenyl-9-H-4, 5-Diazafluorene (OXD-Spiro-DF), were successfully prepared. Europium complexes, Eu(DBM) 3 (OMe-Spiro-DF) and Eu(DBM) 3 (OXD-Spiro-DF) (DBM=dibenzolylmethane) based on the two ligands were designed and synthesized. For a double-layer device with configuration of indium tin oxide (ITO)/N, N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine (TPD)/Eu(DBM) 3 (OXD-Spiro-DF) or Eu(DBM) 3 (OMe-Spiro-DF)/Mg/Ag, compared with the device based on complex Eu(DBM) 3 (OMe-Spiro-DF), the brightness and electroluminescent (EL) efficiency of device based on complex Eu(DBM) 3 (OXD-Spiro-DF) with oxadiazole-functionalized ligand OXD-Spiro-DF are significantly improved due to the improvement of electron-transporting ability. A maximum brightness of 154 cd/m 2 was obtained at 17 V in the complex Eu(DBM) 3 (OXD-Spiro-DF), about four times brighter than the corresponding complex Eu(DBM) 3 (OMe-Spiro-DF)

Electrochemical synthesis of MoS2 quantum dots embedded nanostructured porous silicon with enhanced electroluminescence property

Science.gov (United States)

Shrivastava, Megha; Kumari, Reeta; Parra, Mohammad Ramzan; Pandey, Padmini; Siddiqui, Hafsa; Haque, Fozia Z.

2017-11-01

In this report we present the successful enhancement in electroluminescence (EL) in nanostructured n-type porous silicon (PS) with an idea of embedding luminophorous Molybdenum disulfide (MoS2) quantum dots (QD's). Electrochemical anodization technique was used for the formation of PS surface and MoS2 QD's were prepared using the electrochemical route. Spin coating technique was employed for the proper incorporation of MoS2 QD's within the PS nanostructures. The crystallographic analysis was performed using X-ray diffraction (XRD), Raman and Fourier transform infrared (FT-IR) spectroscopy techniques. However, surface morphology was determined using Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The optical measurements were performed on photoluminescence (PL) spectrophotometer; additionally for electroluminescence (EL) study special arrangement of instrumental setup was made at laboratory level which provides novelty to this work. A diode prototype was made comprising Ag/MoS2:PS/Silicon/Ag for EL study. The MoS2:PS shows a remarkable concentration dependent enhancement in PL as well as in EL intensities, which paves a way to better utilize this strategy in optoelectronic device applications.

Phosphorescent rhenium emitters based on two electron-withdrawing diamine ligands: Structure, characterization and electroluminescent performance

Energy Technology Data Exchange (ETDEWEB)

Rui, Mei, E-mail: meirui2015@163.com [College of Science, Hebei North University, Zhangjiakou 075000, Hebei (China); Yuhong, Wang [College of Science, Hebei North University, Zhangjiakou 075000, Hebei (China); Yinting, Wang; Na, Zhang [Communication Training Base of The Headquarters of The General Staff, Zhangjiakou 075100, Hebei (China)

2014-09-15

In this paper, two diamine ligands having electron-withdrawing oxadiazole group and their corresponding Re(I) complexes were synthesized. Their geometric structure, electronic transition, photophysical property, thermal stability and electrochemical property were discussed in detail. Experimental data suggested that both complexes were promising yellow emitters with suited energy levels and good thermal stability for electroluminescent application. The correlation between emission performance and electron-withdrawing group was analyzed. It was found that electron-withdrawing group favored emission performance improvement. Their electroluminescence performance was also explored. Yellow electroluminescence was observed with maximum brightness of 1743 cd/m{sup 2}. - Highlights: • Oxadiazole derived diamine ligands and their Re(I) complexes were synthesized. • Their characters and properties were analyzed and compared in detail. • Electron-withdrawing group was proved to be positive for PL improvement. • Electroluminescence was obtained with maximum brightness of 1743 cd/m{sup 2}.

Electroluminescent refrigeration by ultra-efficient GaAs light-emitting diodes

Science.gov (United States)

Patrick Xiao, T.; Chen, Kaifeng; Santhanam, Parthiban; Fan, Shanhui; Yablonovitch, Eli

2018-05-01

Electroluminescence—the conversion of electrons to photons in a light-emitting diode (LED)—can be used as a mechanism for refrigeration, provided that the LED has an exceptionally high quantum efficiency. We investigate the practical limits of present optoelectronic technology for cooling applications by optimizing a GaAs/GaInP double heterostructure LED. We develop a model of the design based on the physics of detailed balance and the methods of statistical ray optics, and predict an external luminescence efficiency of ηext = 97.7% at 263 K. To enhance the cooling coefficient of performance, we pair the refrigerated LED with a photovoltaic cell, which partially recovers the emitted optical energy as electricity. For applications near room temperature and moderate power densities (1.0-10 mW/cm2), we project that an electroluminescent refrigerator can operate with up to 1.7× the coefficient of performance of thermoelectric coolers with ZT = 1, using the material quality in existing GaAs devices. We also predict superior cooling efficiency for cryogenic applications relative to both thermoelectric and laser cooling. Large improvements to these results are possible with optoelectronic devices that asymptotically approach unity luminescence efficiency.

Blue-light-emitting organic electroluminescence via exciplex emission based on a fluorene derivative

International Nuclear Information System (INIS)

Li Fushan; Chen Zhijian; Wei Wei; Cao Huayu; Gong Qihuang; Teng Feng; Qian Lei; Wang Yuanmin

2004-01-01

The synthesis of a high photoluminescence efficiency (88%, compared with tris(8-hydroxyquinoline)(Alq 3 )) organic material 9,9-Dibutyl-N,N,N,N-tetraphenyl-9H-fluorene-2,7-diamine (DTFD) via Ullmann condensation was reported. Exiciplex emission of the ITO/DTFD/2,2-[1,2-phenylenebis(oxy)]bis(N,N-diphenylacetamide)/Alq 3 /LiF/Al device was observed and the peak wavelength of the emission was measured to be 480 nm, which belongs to the blue region. A turn-on voltage as low as 4 V and maximal brightness as large as 400 cd m -2 were measured. The electroluminescence spectrum was observed to be blue-shifted with increase in applied voltage

Density-matrix approach for the electroluminescence of molecules in a scanning tunneling microscope.

Science.gov (United States)

Tian, Guangjun; Liu, Ji-Cai; Luo, Yi

2011-04-29

The electroluminescence (EL) of molecules confined inside a nanocavity in the scanning tunneling microscope possesses many intriguing but unexplained features. We present here a general theoretical approach based on the density-matrix formalism to describe the EL from molecules near a metal surface induced by both electron tunneling and localized surface plasmon excitations simultaneously. It reveals the underlying physical mechanism for the external bias dependent EL. The important role played by the localized surface plasmon on the EL is highlighted. Calculations for porphyrin derivatives have reproduced corresponding experimental spectra and nicely explained the observed unusual large variation of emission spectral profiles. This general theoretical approach can find many applications in the design of molecular electronic and photonic devices.

Blue-light-emitting organic electroluminescence via exciplex emission based on a fluorene derivative

Energy Technology Data Exchange (ETDEWEB)

Li Fushan [Department of Physics, State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, 100871 (China); Chen Zhijian [Department of Physics, State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, 100871 (China); Wei Wei [Department of Physics, State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, 100871 (China); Cao Huayu [Department of Physics, State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, 100871 (China); Gong Qihuang [Department of Physics, State Key Laboratory for Artificial Microstructures and Mesoscopic Physics, Peking University, 100871 (China); Teng Feng [Institute of Optoelectronic Technology, Northern Jiaotong University, Beijing 100044 (China); Qian Lei [Institute of Optoelectronic Technology, Northern Jiaotong University, Beijing 100044 (China); Wang Yuanmin [Institute of Optoelectronic Technology, Northern Jiaotong University, Beijing 100044 (China)

2004-06-21

The synthesis of a high photoluminescence efficiency (88%, compared with tris(8-hydroxyquinoline)(Alq{sub 3})) organic material 9,9-Dibutyl-N,N,N,N-tetraphenyl-9H-fluorene-2,7-diamine (DTFD) via Ullmann condensation was reported. Exiciplex emission of the ITO/DTFD/2,2-[1,2-phenylenebis(oxy)]bis(N,N-diphenylacetamide)/Alq{sub 3}/LiF/Al device was observed and the peak wavelength of the emission was measured to be 480 nm, which belongs to the blue region. A turn-on voltage as low as 4 V and maximal brightness as large as 400 cd m{sup -2} were measured. The electroluminescence spectrum was observed to be blue-shifted with increase in applied voltage.

The effect of complexation with platinum in polyfluorene derivatives: A photo- and electro-luminescence study

International Nuclear Information System (INIS)

Assaka, Andressa M.; Hu Bin; Mays, Jimmy; Iamazaki, Eduardo T.; Atvars, Teresa D.Z.; Akcelrud, Leni

2011-01-01

The synthesis and characterization of a polymeric structure containing fluorene units statistically linked to 3-cyclohexyl-thiophene and bipyridine PFOTBipy-poly[(4-hexylthiophene-2,5-diyl)(9,9-dihexyl-fluoren-2,7-diyl) -co-(bipyridine-5.5'-diyl)(9,9-dihexyl-fluoren-2,7-diyl)], is reported. The complexation with platinum was possible through the bipyridil units present in 10%, 50% and 100% content. The structure has a fluorenyl moiety between each bipyridine and thiophene groups resulting in a stable and efficient light-emitting polymeric material combining the well known emissive properties of fluorene, the charge mobility generated by thiophene and the electron-transfer properties of a metal complex as well. All the polymers were photo and electroluminescent materials, and showed phosphorescence at low temperatures. Photoluminescence properties were studied by steady state and time resolved spectroscopy and showed changes of both emission peak and relative intensity of the emission bands depending on the relative amount of the platinum complex. The electroluminescence followed the trends found for photoluminescence. The blue emission of the copolymer without platinum is due to the fluorenyl segments and for higher complex contents the emission is characteristic of the aggregates involving the bipyridinyl moieties. Therefore, emission color can be tuned by the complex content. The turn-on voltage was strongly reduced from 22 to 8 V for the 100% complexed copolymer, as compared to the device made with the non complexed one, but the luminance decreased, due to quenching or trapping effects. - Research Highlights: →Statistic copolymer containing fluorine, thiophene and bipyridine. →Complexation of platinum with platinum with bipyridine. →Electroluminescence and electrophosphorescence at low temperatures. →Emission color can be tuned by the complex content.

Effect of γ-quanta on electroluminescent emitters with zinc sulfide luminophores

International Nuclear Information System (INIS)

Vershchagin, I.K.; Kokin, S.M.; Pautkina, A.V.

1993-01-01

The electroluminescent light sources used in data processing systems can operate under various conditions, particularly in the presence of a significant background radiation. In this work, the authors have investigated the effect of γ-irradiation on the main properties of electroluminescent emitters (ELE) prepared from polycrystalline luminophores of various grades. Such emitters are plane structures consisting of transparent and opaque electrodes and a layer of the luminophore distributed in the dielectric. The ELE were excited with a sinusoidal voltage (220 V; 0.4-1 kHz) at room temperature

Temperature dependence of electron mobility, electroluminescence and photoluminescence of Alq{sub 3} in OLED

Energy Technology Data Exchange (ETDEWEB)

Mu Haichuan; White, Dan; Sharpton, Buck [Office of Electronic Miniaturization, University of Alaska at Fairbanks, AK 99701 (United States); Klotzkin, David [Department of Electrical and Computer Engineering and Computer Sciences, University of Cincinnati, Cincinnati, OH 45221 (United States); De Silva, Ajith; Wagner, Hans Peter [Department of Physics, University of Cincinnati, Cincinnati, OH 45221 (United States)], E-mail: fnhm@uaf.edu

2008-12-07

The correlation of electroluminescence (EL), photoluminescence (PL) and electron mobility were investigated over temperature from 60 to 300 K in small-molecule organic light emitting diode (OLED) structures. The devices consisted of ITO/PEDOT(50 nm)/TPD(50 nm)/Alq{sub 3}(60 nm)/LiF(1 nm)/Al(90 nm), and were fabricated with high-vacuum sublimation/evaporation in a cross-linked configuration. Electron mobility was measured using an ac analysis of the device optical modulation characteristics, while PL and EL were measured by measuring optical power out at fixed pump power of 1 mW, and analysis of dc brightness-voltage (L-V) characteristics, respectively. PL intensity and mobility had a clear maximum at around 220 K, while EL efficiency was constant below 220 K and decrease monotonically above. The reason for the temperature dependent EL, PL and electron mobility behaviour will be discussed.

Electroluminescence efficiencies of erbium in silicon-based hosts

Energy Technology Data Exchange (ETDEWEB)

Cueff, Sébastien, E-mail: sebastien-cueff@brown.edu, E-mail: christophe.labbe@ensicaen.fr [Centre de Recherche sur les Ions, les Matériaux et la Photonique (CIMAP), UMR 6252 CNRS/CEA/Ensicaen/UCBN, Caen 14050 (France); School of Engineering, Brown University, Providence, Rhode Island 02912 (United States); Manel Ramírez, Joan; Berencén, Yonder; Garrido, Blas [MIND-IN2UB, Department Electrònica, Universitat de Barcelona, Martí i Franquès 1, Barcelona 08028 (Spain); Kurvits, Jonathan A.; Zia, Rashid [School of Engineering, Brown University, Providence, Rhode Island 02912 (United States); Department of Physics, Brown University, Providence, Rhode Island 02912 (United States); Rizk, Richard; Labbé, Christophe, E-mail: sebastien-cueff@brown.edu, E-mail: christophe.labbe@ensicaen.fr [Centre de Recherche sur les Ions, les Matériaux et la Photonique (CIMAP), UMR 6252 CNRS/CEA/Ensicaen/UCBN, Caen 14050 (France)

2013-11-04

We report on room-temperature 1.5 μm electroluminescence from trivalent erbium (Er{sup 3+}) ions embedded in three different CMOS-compatible silicon-based hosts: SiO{sub 2}, Si{sub 3}N{sub 4}, and SiN{sub x}. We show that although the insertion of either nitrogen or excess silicon helps enhance electrical conduction and reduce the onset voltage for electroluminescence, it drastically decreases the external quantum efficiency of Er{sup 3+} ions from 2% in SiO{sub 2} to 0.001% and 0.0004% in SiN{sub x} and Si{sub 3}N{sub 4}, respectively. Furthermore, we present strong evidence that hot carrier injection is significantly more efficient than defect-assisted conduction for the electrical excitation of Er{sup 3+} ions. These results suggest strategies to optimize the engineering of on-chip electrically excited silicon-based nanophotonic light sources.

Electroluminescence of erbium in Al/α-Si:H(Er)/p-c-Si/Al structure

International Nuclear Information System (INIS)

Kon'kov, I.O.; Kuznetsov, A.N.; Pak, P.E.; Terukov, E.I.; Granitsyna, L.S.

2001-01-01

It is informed for the first time on the observation of the erbium intensive electroluminescence from the amorphous hydrated silicon layer by application of the Al/α-Si:H(Er)/p-c-Si/Al structure in the direct shift mode. The above structure is the n-p-heterostructure with the barrier values of 0.3-0.4 eV for the electrons and 0.9-1.1 eV for the holes. The electroluminescence efficiency is evaluated at the level ∼ 2 x 10 -5 . The electroluminescence effect in the Al/α-Si:H(Er)/p-c-Si/Al structure is connected with the hole tunneling from the crystal silicon by the amorphous silicon localized states with the subsequent release into the valent zone [ru

The synthesis and study of new electroluminescent materials

International Nuclear Information System (INIS)

Pillow, J.

1998-01-01

Dendrimers offer many potential advantages over other organic electroluminescent materials that have been developed for use in light emitting diodes. This thesis describes the preparation of new electroluminescent dendrimers that consist of a luminescent core, charge-transporting stilbene dendrons and solubilising t-butyl surface groups. Choosing the core to have a longer conjugation length than the dendrons establishes an energy gradient that ensures that light emission occurs from the dendrimer core. Two convergent syntheses were developed for the preparation of dendrons that had aldehyde, bromide and styryl focal groups. The Heck reaction between styrene focused dendrons and 3,5-dibromoaryls was used to increase the dendron generation. This reaction was then alternated with the Wittig or Stille reactions in an iterative cycle to prepare dendrons of up to the third generation. The luminescent cores were chosen to be 1,4-distyrylbenzene, 1,4-distyrylanthracene and meso-tetraaryl porphyrin to emit blue, green and red light respectively. Dendrimers up to the third generation were prepared containing these cores. Further control over the emission colour was demonstrated by the chelation of metals into the porphyrin core. Computer modelling was used to predict the conformations of the dendrimers, with confirmation provided by GPC and X-ray crystallography. The modelled structures were then used to interpret the photoluminescence and electroluminescence spectra. Electrochemical analyses allowed the comparison of the HOMO and LUMO energy levels with the Fermi levels of the metal electrodes, which was used to explain the behaviour of the dendrimers in single layer light-emitting diodes. (author)

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

Energy Technology Data Exchange (ETDEWEB)

Tregnago, G.; Fléchon, C.; Cacialli, F., E-mail: amateo@polymat.eu, E-mail: f.cacialli@ucl.ac.uk [Department of Physics and Astronomy and London Centre for Nanotechnology, University College London, London WC1E 6BT (United Kingdom); Choudhary, S. [School of Soft Matter Research, Freiburg Institute for Advanced Studies (FRIAS), Albert-Ludwigs-Universität Freiburg, Albertstraße 19, 79104 Freiburg (Germany); Institut für Organische Chemie und Biochemie, Albert-Ludwigs-Universität Freiburg, Albertstraße 21, 79104 Freiburg (Germany); Gozalvez, C. [POLYMAT, University of the Basque Country UPV/EHU, Avenida de Tolosa 72, E-20018 Donostia-San Sebastian (Spain); Mateo-Alonso, A., E-mail: amateo@polymat.eu, E-mail: f.cacialli@ucl.ac.uk [POLYMAT, University of the Basque Country UPV/EHU, Avenida de Tolosa 72, E-20018 Donostia-San Sebastian (Spain); Ikerbasque, Basque Foundation for Science, Bilbao (Spain)

2014-10-06

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ∼1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ∼1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

International Nuclear Information System (INIS)

Tregnago, G.; Fléchon, C.; Cacialli, F.; Choudhary, S.; Gozalvez, C.; Mateo-Alonso, A.

2014-01-01

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ∼1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ∼1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

Science.gov (United States)

Tregnago, G.; Fléchon, C.; Choudhary, S.; Gozalvez, C.; Mateo-Alonso, A.; Cacialli, F.

2014-10-01

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ˜1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ˜1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Synthesis and Electroluminescence Properties of 3-(Trifluoromethylphenyl-Substituted 9,10-Diarylanthracene Derivatives for Blue Organic Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Sang Woo Kwak

2017-10-01

Full Text Available Diaryl-substituted anthracene derivatives containing 3-(trifluoromethylphenyl groups, 9,10-diphenyl-2-(3-(trifluoromethylphenylanthracene (1, 9,10-di([1,1′-biphenyl]-4-yl-2-(3-(trifluoromethylphenylanthracene (2, and 9,10-di(naphthalen-2-yl-2-(3-(trifluoromethylphenylanthracene (3 were synthesized and characterized. The compounds 1–3 possessed high thermal stability and proper frontier-energy levels, which make them suitable as host materials for blue organic light-emitting diodes. The electroluminescent (EL emission maximum of the three N,N-diphenylamino phenyl vinyl biphenyl (DPAVBi-doped (8 wt % devices for compounds 1–3 was exhibited at 488 nm (for 1 and 512 nm (for 2 and 3. Among them, the 1-based device displayed the highest device performances in terms of brightness (Lmax = 2153.5 cd·m−2, current efficiency (2.1 cd·A−1, and external quantum efficiency (0.8%, compared to the 2- and 3-based devices.

Excitation spectra and forward injection electroluminescence of Er/sup 3+/ ions in ZnS

International Nuclear Information System (INIS)

Jiaqi, Y.; Tianren, Z.; Wenlian, L.

1985-01-01

Trivalent rare earth ions (RE/sup 3+/) are efficient luminescent centers for electroluminescence (EL) of thin films of II-VI compounds, which are promising display materials and attract more and more attention. The mechanism of all EL devices of RE/sup 3+/ available so far is hot electron impact excitation. Based on the analysis of excitation spectra of RE/sup 3+/ in ZnS, the authors have pointed out the possibility of a new type of EL of RE/sup 3+/ - forward injection EL, which have potential of reducing operation voltage and raising efficiency. The forward injection EL of RE/sup 3+/ has been observed and experimentally proven in ZnS:Er/sup 3+/ diode for the first time

Crystal growth of electroluminescent ZnS:Cu,Cl phosphor and its TiO2 coating by sol-gel method for thick-film EL device

International Nuclear Information System (INIS)

Han, Sang-Do; Singh, Ishwar; Singh, Devender; Lee, You-He; Sharma, Gaytri; Han, Chi-Hwan

2005-01-01

Bigger-sized spherical particle of ZnS:Cu,Cl to be employed for electroluminescent (EL) device has been synthesized using a new eutectic mixture as flux. The best composition of the flux was the mixture of BaCl 2 .2H 2 O, MgCl 2 .6H 2 O and NaCl in the mole percentage ratio of 13.8:39.9:46.2 and when the total amount of the mixture was 6% of the total weight of ZnS. The phosphor was synthesized firing at higher temperatures in two steps. First step firing at 1150 deg. C gave the hexagonal phase of the ZnS phosphor particles. Low intensity ball-milling of the phosphor pastes in solvents converted hexagonal phase partially to the cubic phase of the phosphor, which is an essential step. Mixing with copper sulfate or copper(I) halides and magnesium chloride and then firing (second step) at 750 deg. C gave a phosphor with better luminescent characteristics and converting to almost 100% cubic phase. The phosphor particles having size >0.020 mm size were sieved and coated with TiO 2 made by sol-gel process using titanium(IV)-isopropoxide as a precursor. The phosphor particles were coated twice with the TiO 2 sol and finally calcined at 400 deg C in nitrogen atmosphere. The EL devices were fabricated with the synthesized phosphor using a screen-printing method

Functional electronic screen printing – electroluminescent smart fabric watch

OpenAIRE

de Vos, Marc; Torah, Russel; Beeby, Steve; Tudor, John

2013-01-01

Motivation for screen printed smart fabrics.Introduce functional electronic screen printing on fabrics.Printed smart fabric watch design.Printing process for electroluminescent watch.Demonstration video.Conclusions and further work.Examples of other screen printed smart fabrics.

Photo- and electroluminescence of undoped and rare earth doped ZnO electroluminors

International Nuclear Information System (INIS)

Bhushan, S.; Pandey, A.N.; Kaza, B.R.

1977-01-01

A series of undoped and rare earth (Dy, Yb, Nd, Pr, Gd, La, Sm and Er) doped ZnO electroluminors have been prepared and their photo- (PL) and electroluminescence (EL) spectra at different concentrations of rare earth ions have been investigated. PL and EL spectra of undoped electroluminescence consist of three peaks. Due to the addition of the rare earth ions these peaks are shifted either to the longer or to the shorter wavelength side. The intensities are also either decreased or increased. Experimental results favour the donor-accepted model for this system. (Auth.)

PANI Branches onto Donor-Acceptor Copolymers: Synthesis, Characterization and Electroluminescent Properties of New 2D-Materials

Directory of Open Access Journals (Sweden)

Ignacio A. Jessop

2018-05-01

Full Text Available A new series of two-dimensional statistical conjugated polymers based on aniline and 9,9-dihexylfluorene as donor units and benzo- or naphtho-quinoxaline/thiadiazole derivatives as acceptor moieties, possessing PANI segments as side chains, were designed and synthesized. To investigate the effects of the perpendicular PANI branches on the properties of the main chain, the optical, electrochemical, morphological and electroluminescence properties were studied. The 2D materials tend to possess lower molecular weights and to absorb and to emit light red-shifted compared to the trunk 1D-polymers, in the yellow-red region of the visible spectrum. The 1D- and 2D-conjugated polymers present optical band gaps ranging from 2.15–2.55 eV, HOMO energy levels between −5.37 and −5.60 eV and LUMO energy levels between −3.02 and −3.29 eV. OLED devices based on these copolymers were fabricated. Although the performances were far from optimal due to the high turn-on voltages for which electroluminescence phenomena occur, a maximum luminescence of 55,100 cd/m2 together with a current density of 65 mA/cm2 at 18.5 V were recorded for a 2D-copolymer, PAFC6TBQ-PANI.

Influence of Exciplex formation on the electroluminescent properties of dimeric Zn (II) bis-2-(2'-hydroxyphenyl) benzoxazole complex and monomeric Zn (II) 2-(1'-hydroxynaphthyl) benzothiazole complex

Science.gov (United States)

Prakash, Sattey; Anand, R. S.; Manoharan, S. Sundar

2011-10-01

In this paper we present the factors affecting electroluminescent properties of Zinc complexes of oxazole & thiazole derivatives. Electroluminescent spectra of the Zinc (II) complex of bis-[2-(2'-hydroxyphenyl) benzoxazole], [Zn (HPBO)2]2 and 2-(1'-hydroxynaphthyl) benzothiazole [Zn (HNBT)2] show unusual broadening and shows structural and photophysical similarity with [Zn (HPBT)2]2, a dimeric complex. The [Zn (HPBO)2]2 complex as an emissive layer in the device structure ITO /PEDOT:PSS /TPD (30nm) /[Zn (HPBO)2]2 (60nm) /BCP (6nm) /Ca (3nm) /Al (200nm) shows a broad bluish green emission, with a full width at half maxima (FWHM1˜70nm). The EL spectra is much broader compared to the PL spectra because of exciplex formation at the interfacial region between the emissive layer (EML) & hole transport layer (HTL). We also show the device performance of Zinc 2-(1'-hydroxynaphthyl) benzothiazole [Zn (HNBT)2] complex as emissive layer. Distinctly this device shows a broad greenish yellow emission with a peak maxima at 535nm and 690nm, owing to the exciplex formation between electron transport layer (ETL) and emissive layer (EML), which is in sharp contrast to the exciplex formation across the HTL-EML interface observed for the [Zn (HPBO)2]2 complex.

Supporting Information Blue and White light electroluminescence in ...

Indian Academy of Sciences (India)

Administrator

Blue and White light electroluminescence in a multilayer OLED using a new Aluminium complex. Pabitra K. Nayak a. , Neeraj Agarwal a. , Farman Ali a. , Meghan P. Patankar b. , K. L.. Narasimhan b. *, N. Periasamy a. *. 1. Department of Chemical Sciences,. 2. Department of Condensed Matter Physics and. Materials ...

Color tunable electroluminescence and resistance switching from a ZnO-nanorod–TaO_x–p-GaN heterojunction

International Nuclear Information System (INIS)

Zhao, J L; Teo, K L; Zheng, K; Sun, X W

2016-01-01

Well-aligned ZnO nanorods have been prepared on p-GaN–sapphire using a vapor phase transport (VPT) technique. A thin sputtered layer of TaO_x is employed as the intermediate layer and an n-ZnO–TaO_x–p-GaN heterojunction device has been achieved. The current transport of the heterojunction exhibited a typical resistance switching behavior, which originated from the filament forming and breaking in the TaO_x layer. Color controllable electroluminescence (EL) was observed from the biased heterojunction at room temperature. Bluish-white wide band emission is achieved from the forward biased device in both the high resistance and low resistance states, while red emission can only be observed for the reverse biased device in the low resistance state. The correlation between the EL and resistance switching has been analyzed in-depth based on the interface band diagram of the heterojunction. (paper)

Electroluminescence from graphene excited by electron tunneling

International Nuclear Information System (INIS)

Beams, Ryan; Bharadwaj, Palash; Novotny, Lukas

2014-01-01

We use low-energy electron tunneling to excite electroluminescence in single layer graphene. Electrons are injected locally using a scanning tunneling microscope and the luminescence is analyzed using a wide-angle optical imaging system. The luminescence can be switched on and off by inverting the tip–sample bias voltage. The observed luminescence is explained in terms of a hot luminescence mechanism. (paper)

Liquid crystalline networks for electroluminescent displays

International Nuclear Information System (INIS)

Contoret, A.E.A.

2001-09-01

This work presents the first low molar mass organic electroluminescent (EL) material to form a nematic glass and then emit plane-polarised light from the vitrified state on application of an electric field. Photocrosslinkable molecules are also discussed which form insoluble films on illumination with ultra-violet light. This approach combines the ease of deposition of small molecules with the robustness and stability of polymers, allowing simple fabrication of multi-layer EL devices and photo-patterning. A range of conjugated low molar-mass molecules are considered, containing the anthracene, perylene and fluorene cores, with the aims of producing a general recipe for efficient EL, based on ordered, stable nematics at room temperature. Many physical properties are compared and molecular mechanics modeling is used to represent molecular geometries. An acrylate and several diene photo-polymerisable derivatives of the fluorenes undergo photo-crosslinking. Infrared and photoluminescence spectroscopy is used to examine crosslinking in detail and to optimise exposure conditions. The diene shows no significant degradation for an optimal exposure, but requires a high fluence of 100 Jcm -2 to form an insoluble film. A doped photo-alignment layer is used for the first time to obtain polarised El with ratio 11:1 and 80 cdm -2 brightness from the crosslinked diene. The insoluble crosslinked network allows spin coating of an electron transporting over-layer, resulting in increased brightness. Complex impedance spectroscopy and time of flight measurements confirm good material properties with complete depletion of the crosslinkable diene molecule and non-dispersive conduction. Finally, a novel deposition technique, pulsed laser deposition (PLD), is presented, as an alternative to spin coating or vapour deposition. Minimal degradation is observed for optimised deposition conditions and a PLD film is successfully demonstrated in an EL device. (author)

Enhanced Electroluminescence from Silicon Quantum Dots Embedded in Silicon Nitride Thin Films Coupled with Gold Nanoparticles in Light Emitting Devices

Directory of Open Access Journals (Sweden)

Ana Luz Muñoz-Rosas

2018-03-01

Full Text Available Nowadays, the use of plasmonic metal layers to improve the photonic emission characteristics of several semiconductor quantum dots is a booming tool. In this work, we report the use of silicon quantum dots (SiQDs embedded in a silicon nitride thin film coupled with an ultra-thin gold film (AuNPs to fabricate light emitting devices. We used the remote plasma enhanced chemical vapor deposition technique (RPECVD in order to grow two types of silicon nitride thin films. One with an almost stoichiometric composition, acting as non-radiative spacer; the other one, with a silicon excess in its chemical composition, which causes the formation of silicon quantum dots imbibed in the silicon nitride thin film. The ultra-thin gold film was deposited by the direct current (DC-sputtering technique, and an aluminum doped zinc oxide thin film (AZO which was deposited by means of ultrasonic spray pyrolysis, plays the role of the ohmic metal-like electrode. We found that there is a maximum electroluminescence (EL enhancement when the appropriate AuNPs-spacer-SiQDs configuration is used. This EL is achieved at a moderate turn-on voltage of 11 V, and the EL enhancement is around four times bigger than the photoluminescence (PL enhancement of the same AuNPs-spacer-SiQDs configuration. From our experimental results, we surmise that EL enhancement may indeed be due to a plasmonic coupling. This kind of silicon-based LEDs has the potential for technology transfer.

Organic optoelectronics:materials,devices and applications

Institute of Scientific and Technical Information of China (English)

LIU Yi; CUI Tian-hong

2005-01-01

The interest in organic materials for optoelectronic devices has been growing rapidly in the last two decades. This growth has been propelled by the exciting advances in organic thin films for displays, low-cost electronic circuits, etc. An increasing number of products employing organic electronic devices have become commercialized, which has stimulated the age of organic optoelectronics. This paper reviews the recent progress in organic optoelectronic technology. First, organic light emitting electroluminescent materials are introduced. Next, the three kinds of most important organic optoelectronic devices are summarized, including light emitting diode, organic photovoltaic cell, and photodetectors. The various applications of these devices are also reviewed and discussed in detail. Finally, the market and future development of optoelectronic devices are also demonstrated.

Electroluminescence of organic light-emitting diodes with an ultra-thin layer of dopant

Energy Technology Data Exchange (ETDEWEB)

Li Weizhi [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Yu Junsheng [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jsyu@uestc.edu.cn; Wang, Tao [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Jiang, Yadong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jiangyd@uestc.edu.cn; Wei, Bangxiong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2008-03-15

Conventional fluorescent dyes, i.e., 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), 5,12-dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA) and 5,6,11,12-tetraphenylnaphthacene (Rubrene), were used to investigate the performance of organic light-emitting diodes (OLEDs) based on indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine (NPB)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3})/MgAg. The dyes were either inserted into devices as an ultra-thin film at the NPB/Alq{sub 3} interface by sequential evaporation, or doped into the Alq{sub 3} emission layer by co-evaporation with the doping ratio about 2%. Electroluminescence (EL) spectra of devices indicated that concentration quenching effect (CQE) of the dye-dopant was slightly bigger in the former than in the latter, while the degrees of CQE for three dopants are in the order of DMQA > DCJTB > Rubrene suggested by the difference in EL spectra and performances of devices. In addition, EL process of device with an ultra-thin layer of dopant is dominated by direct carrier trapping (DCT) process due to almost no holes recombine with electrons in Alq{sub 3}-host layer.

Influence of annealing temperature on erbium ion electroluminescence in Si : (Er,O) diodes with (111) substrate orientation

CERN Document Server

Sobolev, N A; Nikolaev, Y A

2001-01-01

A study has been made of the influence of temperature of the second annealing that promotes formation of optically and electrically active centers o the erbium ion electroluminescence at lambda approx = 1.54 mu m wavelength in (111) Si : (Er,O) diodes. Doping has been performed by implantation of erbium and oxygen ions at 2.0, 1.6 MeV and 0.28, 0.22 MeV energies and 3 x 10 sup 1 sup 4 cm sup - sup 2 and 3 x 10 sup 1 sup 5 cm sup - sup 2 doses, respectively. The room temperature electroluminescence intensity under the breakdown regime increases with increasing annealing temperature from 700 to 950 deg C. After annealing in the range of 975-1100 deg C, erbium electroluminescence under the breakdown regime is not observed due to appearance of microplasmas. The injection electroluminescence intensity at 80 K decreases with increasing temperature from 700 to 1100 deg C

Enhanced phosphorescence and electroluminescence in triplet emitters by doping gold into cadmium selenide/zinc sulfide nanoparticles

International Nuclear Information System (INIS)

Liu, H.-W.; Laskar, Inamur R.; Huang, C.-P.; Cheng, J.-A.; Cheng, S.-S.; Luo, L.-Y.; Wang, H.-R.; Chen, T.-M.

2005-01-01

Gold-cadmium selenide/zinc sulfide (Au-CdSe/ZnS) nanocomposites (NCs) were synthesized and characterized by transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, ultraviolet-visible (UV-visible) absorption and photoluminescence (PL) emission spectroscopy. The PL intensity in the Au-CdSe/ZnS NCs system was found to be much greater than that of CdSe/ZnS nanoparticles (NPs) alone, because of the surface-enhanced Raman scattering of Au NPs. Adding Au-CdSe/ZnS NCs to the cyclometalated iridium(III) complex (Ir-complex) greatly enhanced the PL intensity of a triplet emitter. Three double-layered electroluminescence (EL) devices were fabricated where the emitting zone contains the definite mixture of Ir-complex and the NCs [molar concentration of Ir-complex/NCs = 1:0 (Blank, D-1), 1:1 (D-2) and 1:3 (D-3)] and the device D-2 exhibited optimal EL performances

Interfacial exciplex electroluminescence between diamine derivatives with starburst molecular structure and tris(acetylacetonato)-(mono-phenothroline) thulium

International Nuclear Information System (INIS)

He Hong; Li Wenlian; Su Zisheng; Chu Bei; Bi Defeng; Chen Yiren; Wang Dan; Su Wenming; Li Bin

2009-01-01

The authors demonstrate the interfacial exciplex electroluminescence (EL) between tris(acetylacetonato)-(mono-phenothroline) thulium [Tm(AcA) 3 phen] and two diamine derivatives with starburst molecular structure- 4,4',4''-tris[2-naphthyl(phenyl)amino]triphenylamine (2-TNATA) and 4,4',4''-tris[3-methyl-pheny(phenyl)-amino]triphenyl-amine (m-MTDATA), both of which have the same ionization potential (IP) (approximately 5.1 eV). When the Tm-complex and the two diamine derivatives are respectively used as the electron accepter and donors, the two EL devices exhibit different exciplex emissions, which verifies our previously reported opinion regarding the effect of the different substitutes on exciplex emission [W.M. Su, W.L. Li, Q. Xin, Z.S. Su, B. Chu, D.F. Bi, H. He, J.H. Niu, Appl. Phys. Lett. 91 (2007) 043508]. When the mixture of the two diamine derivatives is used as a donor, a white EL device with the Commission International de l'Eclairage (CIE) coordinates of (0.277, 0.323) is achieved. The exciplex formation mechanisms of the devices with the two different donors are discussed

Electroluminescence of a-Si/c-Si heterojunction solar cells after high energy irradiation

Energy Technology Data Exchange (ETDEWEB)

Ferrara, Manuela

2009-11-24

The crystalline silicon as absorber material will certainly continue to dominate the market for space applications of solar cells. In the contribution under consideration the applicability of a-Si:H/c-Si heterojunction solar cells in space has been tested by the investigation of the cell modification by high energy protons and comparing the results to the degradation of homojunction crystalline silicon reference cells. The investigated solar cells have been irradiated with protons of different energies and doses. For all investigated solar cells the maximum damage happens for an energy of about 1.7 MeV and is mainly due to the decrease of the effective minority carrier diffusion length in the crystalline silicon absorber. Simulations carried out by AFORS-HET, a heterojunction simulation program, also confirmed this result. The main degradation mechanism for all types of devices is the monotonically decreasing charge carrier diffusion length in the p-type monocrystalline silicon absorber layer. For the heterojunction solar cell an enhancement of the photocurrent in the blue wavelength region has been observed but only in the case of heterojunction solar cell with intrinsic a-Si:H buffer layer. Additionally to the traditional characterization techniques the electroluminescence technique used for monitoring the modifications of the heteroluminescence technique used for monitoring the modifications of the heterointerface between amorphous silicon and crystalline silicon in solar cells after proton irradiation. A direct relation between minority carrier diffusion length and electroluminescence quantum efficiency has been observed but also details of the interface modification could be monitored by this technique.

Synthesis and electroluminescent properties of anthracene derivatives containing electron-withdrawing oxide moieties

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jhin-yeong; Na, Eun Jae; Park, Soo Na [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Lee, Seok Jae [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@wow.hongik.ac.kr [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2014-10-15

Highlights: • Blue fluorescent material is important for application in full-color displays. • We have synthesized emitters based on anthracene connected with oxide moieties. • 1C shows a highly efficient blue EL emission due to electron-injection property. - Abstract: A series of new blue-emitting materials: (4-(10-(naphthalen-2-yl)anthracen-9-yl)phenyl)(phenyl)methanone (1); 9-(naphthalen-2-yl)-10-(4-((diphenyl)phosphine oxide)phenyl)anthracene (2); 9-(naphthalen-2-yl)-10-(4-(phenylsulfonyl)phenyl)anthracene (3) were designed and synthesized via Suzuki cross-coupling reaction. Multilayer OLEDs were fabricated in the following sequence: ITO (180 nm)/NPB (50 nm)/blue materials 1–3 (30 nm)/TPBi (15 nm)/Liq (2 nm)/Al (100 nm). All devices showed the efficient blue EL emissions. In particular, the device using 1 as an emitter exhibited efficient blue electroluminescent properties with a maximum luminous, power, external quantum efficiency and CIE coordinates of 0.36 cd/A, 0.90 lm/W, 0.55% at 20 mA/cm{sup 2} and (x = 0.16, y = 0.20) at 10.0 V, respectively.

Efficient electroluminescence from a perylenediimide fluorophore obtained from a simple solution processed OLED

International Nuclear Information System (INIS)

Cespedes-Guirao, F J; Fernandez-Lazaro, F; Sastre-Santos, A; Garcia-Santamaria, S; Bolink, H J

2009-01-01

Simple solution processed organic light emitting diodes are used to screen the performance of two types of highly efficient, narrow band red emitting fluorescent perylenediimides (PDIs). PDIs substituted at the diimide positions seem to form aggregates in the thin film architecture as evidenced by the shifted electroluminescent spectrum. When substituted on the bay position and when used both as the emitting and the electron transporting specie, bright electroluminescence with a narrow width around 610 nm reaching 500 cd m -2 at moderate voltages was observed, demonstrating the usefulness of these fluorophores for OLED applications.

Efficient light emitting devices based on phosphorescent partially doped emissive layers

KAUST Repository

Yang, Xiaohui

2013-05-29

We report efficient organic light emitting devices employing an ultrathin phosphor emissive layer. The electroluminescent spectra of these devices can be tuned by introducing a low-energy emitting phosphor layer into the emission zone. Devices with the emissive layer consisting of multiple platinum-complex/spacer layer cells show a peak external quantum efficiency of 18.1%, which is among the best EQE values for platinum-complex based light emitting devices. Devices with an ultrathin phosphor emissive layer show stronger luminance decay with the operating time compared to the counterpart devices having a host-guest emissive layer.

Automatic Detection of Inactive Solar Cell Cracks in Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2017-01-01

We propose an algorithm for automatic determination of the electroluminescence (EL) signal threshold level corresponding to inactive solar cell cracks, resulting from their disconnection from the electrical circuit of the cell. The method enables automatic quantification of the cell crack size...

Synthesis and Electroluminescent Properties of Julolidine-π-Juloidine Type Materials with the Bulky Adamantane Groups

Energy Technology Data Exchange (ETDEWEB)

Lee, Kum Hee; Yoon, Seung Soo [Sungkyunkwan Univ., Suwon (Korea, Republic of); Lee, Seok Jae; Kim, Young Kwan [Hongik Univ., Seoul (Korea, Republic of)

2012-11-15

A main problem of red emitting material, which contributes to their low EL performances, is the concentration quenching due to the effective self aggregation and the consequent formation of excimers. To avoid this drawback and thus improve the EL properties of red fluorescent OLED devices, many synthetic efforts have been conducted to develop new emitting materials with the structural motifs to suppress self-aggregation by the weakening intermolecular attractive interactions. Particularly, the introduction of bulky moieties in the emitters would provide the steric hindrance between emitting materials in solid state devices and thus reduce the self-aggregation. Nevertheless, EL performances of red materials still need to be improved for the practical applications. In conclusion, we designed and synthesized three julolidine-π-juloidine type emitting materials (1-3) with the bulky adamantane groups. To study their electroluminescent properties, the multilayered OLED devices with the structure of ITO/NPB (40 nm)/ADN : 1-3 (x%) (20 nm)/Alq{sub 3} (40 nm)/Liq (2 nm)/Al were fabricated. All devices using emitters 1-3 showed the efficient emissions, in which their EL performances depend on the structure of emitters sensitively. Particularly, a device using emitter 3 exhibited the efficient orange-red emission with the luminous and power efficiencies of 4.79 cd/A and 1.76 lm/W at 20 mA/cm{sup 2}, respectively. The CIE coordinates of this device was (0.57, 0.42) at 7.0 V.

Automatic Detection of Inactive Solar Cell Cracks in Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2017-01-01

We propose an algorithm for automatic determination of the electroluminescence (EL) signal threshold level corresponding to inactive solar cell cracks, resulting from their disconnection from the electrical circuit of the cell. The method enables automatic quantification of the cell crack size an...

Multifunctional Device based on phosphor-piezoelectric PZT: lighting, speaking, and mechanical energy harvesting.

Science.gov (United States)

Lee, Sunghoon; Kang, Taewook; Lee, Wunho; Afandi, Mohammad M; Ryu, Jongho; Kim, Jongsu

2018-01-10

We demonstrated the tri-functional device based on all powder-processing methods by using ZnS powder as phosphor layer and piezoelectric material as dielectric layer. The fabricated device generated the electroluminescent (EL) light from phosphor and the sound from piezoelectric sheet under a supply of external electric power, and additionally harvested the reverse-piezoelectric energy to be converted into EL light. Under sinusoidal applied voltage, EL luminances were exponentially increased with a maximum luminous efficiency of 1.3 lm/W at 40 V and 1,000 Hz, and sound pressure levels (SPLs) were linearly increased. The EL luminances were linearly dependent on applied frequency while the SPLs showed the parabolic increase behavior below 1,000 Hz and then the flat response. The temperature dependence on EL luminances and SPLs was demonstrated; the former was drastically increased and the latter was slightly decreased with the increase of temperature. Finally, as an energy harvesting application, the piezoelectric-induced electroluminescence effect was demonstrated by applying only mechanical pressure to the device without any external electric power.

Enhancement of Electroluminescence (EL) image measurements for failure quantification methods

DEFF Research Database (Denmark)

Parikh, Harsh; Spataru, Sergiu; Sera, Dezso

2018-01-01

Enhanced quality images are necessary for EL image analysis and failure quantification. A method is proposed which determines image quality in terms of more accurate failure detection of solar panels through electroluminescence (EL) imaging technique. The goal of the paper is to determine the most...

Quantifying Solar Cell Cracks in Photovoltaic Modules by Electroluminescence Imaging

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2015-01-01

This article proposes a method for quantifying the percentage of partially and totally disconnected solar cell cracks by analyzing electroluminescence images of the photovoltaic module taken under high- and low-current forward bias. The method is based on the analysis of the module’s electrolumin...

Interfacial exciplex electroluminescence between diamine derivatives with starburst molecular structure and tris(acetylacetonato)-(mono-phenothroline) thulium

Energy Technology Data Exchange (ETDEWEB)

He Hong [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Li Wenlian [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)], E-mail: wllioel@yahoo.com.cn; Su Zisheng; Chu Bei; Bi Defeng; Chen Yiren; Wang Dan; Su Wenming; Li Bin [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)

2009-02-20

The authors demonstrate the interfacial exciplex electroluminescence (EL) between tris(acetylacetonato)-(mono-phenothroline) thulium [Tm(AcA){sub 3}phen] and two diamine derivatives with starburst molecular structure- 4,4',4''-tris[2-naphthyl(phenyl)amino]triphenylamine (2-TNATA) and 4,4',4''-tris[3-methyl-pheny(phenyl)-amino]triphenyl-amine (m-MTDATA), both of which have the same ionization potential (IP) (approximately 5.1 eV). When the Tm-complex and the two diamine derivatives are respectively used as the electron accepter and donors, the two EL devices exhibit different exciplex emissions, which verifies our previously reported opinion regarding the effect of the different substitutes on exciplex emission [W.M. Su, W.L. Li, Q. Xin, Z.S. Su, B. Chu, D.F. Bi, H. He, J.H. Niu, Appl. Phys. Lett. 91 (2007) 043508]. When the mixture of the two diamine derivatives is used as a donor, a white EL device with the Commission International de l'Eclairage (CIE) coordinates of (0.277, 0.323) is achieved. The exciplex formation mechanisms of the devices with the two different donors are discussed.

Sharp green electroluminescence from 1H-pyrazolo[3,4-b]quinoline-based light-emitting diodes

Science.gov (United States)

Tao, Y. T.; Balasubramaniam, E.; Danel, A.; Jarosz, B.; Tomasik, P.

2000-09-01

A multilayer organic light-emitting diode was fabricated using a fluorescent compound {6-N,N-diethylamino-1-methyl-3-phenyl-1H-pyrazolo[3,4-b]quinoline} (PAQ-NEt2) doped into the hole-transporting layer of NPB {4,4'-bis[N-(1-naphthyl-1-)-N-phenyl-amino]-biphenyl}, with the TPBI {2,2',2″-(1,3,5-phenylene)tris[1-phenyl-1H-benzimidazole]} as an electrontransporting material. At 16% PAQ-NEt2 doping concentration, the device gave a sharp, bright, and efficient green electroluminescence (EL) peaked at around 530 nm. The full width at half maximum of the EL is 60 nm, which is 60% of the green emission from typical NPB/AlQ [where AlQ=tris(8-hydroxyquinoline) aluminum] device. For the same concentration, a maximum luminance of 37 000 cd/m2 was obtained at 10.0 V and the maximum power, luminescence, and external quantum efficiencies were obtained 4.2 lm/W, 6.0 cd/A, and 1.6%, respectively, at 5.0 V.

Blue and green electroluminescence from CdSe nanocrystal quantum-dot-quantum-wells

International Nuclear Information System (INIS)

Lu, Y. F.; Cao, X. A.

2014-01-01

CdS/CdSe/ZnS quantum dot quantum well (QDQW) nanocrystals were synthesized using the successive ion layer adsorption and reaction technique, and their optical properties were tuned by bandgap and strain engineering. 3-monolayer (ML) CdSe QWs emitted blue photoluminescence at 467 nm with a spectral full-width-at-half-maximum of ∼30 nm. With a 3 ML ZnS cladding layer, which also acts as a passivating and strain-compensating layer, the QDQWs acquired a ∼35% quantum yield of the QW emission. Blue and green electroluminescence (EL) was obtained from QDQW light-emitting devices with 3–4.5 ML CdSe QWs. It was found that as the peak blueshifted, the overall EL was increasingly dominated by defect state emission due to poor hole injection into the QDQWs. The weak EL was also attributed to strong field-induced charge separation resulting from the unique QDQW geometry, weakening the oscillator strength of optical transitions

Synthesis, structures, and electroluminescent properties of scandium N,O-chelated complexes toward near-white organic light-emitting diodes.

Science.gov (United States)

Katkova, Marina A; Balashova, Tatyana V; Ilichev, Vasilii A; Konev, Alexey N; Isachenkov, Nikolai A; Fukin, Georgy K; Ketkov, Sergey Yu; Bochkarev, Mikhail N

2010-06-07

Three members of a new class of electroluminescent, neutral, and monomeric scandium N,O-chelate complexes, namely, Sc(III)-tris-2-(2-benzoimidazol-2-yl)phenolate (1), Sc(III)-tris-2-(2-benzoxyazol-2-yl)phenolate (2), and Sc(III)-tris-2-(2-benzothiazol-2-yl)phenolate (3), have been prepared and X-ray characterized. DFT calculations have been performed. In contrast to the most frequently applied dual or multiple dopants in multilayer white OLED devices, all our simpler devices with the configuration of indium tin oxide/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine/neat scandium complex/Yb exhibit close to near-white emission with a blue hue (CIE(x,y) = 0.2147, 0.2379) in the case of 1, a cyan hue (0.2702, 0.3524) in the case of 2, and a yellowish hue (0.3468; 0.4284) in the case of 3.

Electroluminescence from porous silicon due to electron injection from solution

NARCIS (Netherlands)

Kooij, Ernst S.; Despo, R.W.; Kelly, J.J.

1995-01-01

We report on the electroluminescence from p‐type porous silicon due to minority carrier injection from an electrolyte solution. The MV+• radical cation formed in the reduction of divalent methylviologen is able to inject electrons into the conduction band of crystalline and porous silicon. The

Near-infrared electroluminescence emission from an n-InN nanodots/p-Si heterojunction structure

International Nuclear Information System (INIS)

Wu Guoguang; Du Guotong; Gao Fubin; Shen Chunsheng; Li Wancheng; Wang Hui

2012-01-01

An n-InN nanodots/p-Si(1 1 1) heterojunction diode was fabricated by plasma-assisted molecular beam epitaxy. The device shows clear rectifying behaviour with a turn-on voltage of approximately 1.2 V at room temperature. The near-infrared electroluminescence (EL) can be observed under forward bias, which covers a wide wavelength range. In comparison with the photoluminescence spectra, the maximum of the EL spectra has a blueshift which is probably due to the size quantization effect of small-sized InN nanodots and their stronger contribution to the EL intensity. On the other hand, there is an obvious enhancement of the less dominant transitions on the short wavelength side of the EL spectra, which may arise from the recombination of the injected holes with the extremely high-density surface electrons of InN nanodots. (paper)

Synthesis and Electroluminescent Properties of Bis(3H-1,2,3-triazolo-[4,5-b]pyridine-3-olzinc Zn(TAP2

Directory of Open Access Journals (Sweden)

Trinh Dac Hoanh

2012-01-01

Full Text Available A new light-emissive material, bis(3H-1,2,3-triazolo-[4,5-b]pyridine-3-olzinc (Zn(TAP2, has been synthesized and characterized by FT-NMR, FT-IR, UV-Vis, and elemental analysis. The photoluminescence (PL of Zn(TAP2 was measured from the DMF solution at 460 nm. The HOMO (6.5 eV and LUMO (2.8 eV energy levels of Zn(TAP2 were estimated from the measurement of cyclic voltammetry. The devices with structures of ITO/NPB/Zn(TAP2/LiF/Al and ITO/NPB/Zn(TAP2/Alq3/LiF/Al were constructed to investigate their electroluminescent (EL performance. Zn (TAP2 is supposed to be a good emitting material in the EL device.

Electroluminescence color tuning between green and red from metal-oxide-semiconductor devices fabricated by spin-coating of rare-earth (terbium + europium) organic compounds on silicon

Science.gov (United States)

Matsuda, Toshihiro; Hattori, Fumihiro; Iwata, Hideyuki; Ohzone, Takashi

2018-04-01

Color tunable electroluminescence (EL) from metal-oxide-semiconductor devices with the rare-earth elements Tb and Eu is reported. Organic compound liquid sources of (Tb + Ba) and Eu with various Eu/Tb ratios from 0.001 to 0.4 were spin-coated on an n+-Si substrate and annealed to form an oxide insulator layer. The EL spectra had only peaks corresponding to the intrashell Tb3+/Eu3+ transitions in the spectral range from green to red, and the intensity ratio of the peaks was appropriately tuned using the appropriate Eu/Tb ratios in liquid sources. Consequently, the EL emission colors linearly changed from yellowish green to yellowish orange and eventually to reddish orange on the CIE chromaticity diagram. The gate current +I G current also affected the EL colors for the medium-Eu/Tb-ratio device. The structure of the surface insulator films analyzed by cross-sectional transmission electron microscopy (TEM), X-ray diffraction (XRD) analysis, and X-ray photoelectron spectroscopy (XPS) has four layers, namely, (Tb4O7 + Eu2O3), [Tb4O7 + Eu2O3 + (Tb/Eu/Ba)SiO x ], (Tb/Eu/Ba)SiO x , and SiO x -rich oxide. The EL mechanism proposed is that electrons injected from the Si substrate into the SiO x -rich oxide and Tb/Eu/Ba-silicate layers become hot electrons accelerated in a high electric field, and then these hot electrons excite Tb3+ and Eu3+ ions in the Tb4O7/Eu2O3 layers resulting in EL emission from Tb3+ and Eu3+ intrashell transitions.

Interband cascade light emitting devices based on type-II quantum wells

International Nuclear Information System (INIS)

Yang, Rui Q.; Lin, C.H.; Murry, S.J.

1997-01-01

The authors discuss physical processes in the newly developed type-II interband cascade light emitting devices, and review their recent progress in the demonstration of the first type-II interband cascade lasers and the observation of interband cascade electroluminescence up to room temperature in a broad mid-infrared wavelength region (extended to 9 μm)

Bias-polarity-dependent UV/visible transferable electroluminescence from ZnO nanorod array LED with graphene oxide electrode supporting layer

Science.gov (United States)

Liu, Weizhen; Wang, Wei; Xu, Haiyang; Li, Xinghua; Yang, Liu; Ma, Jiangang; Liu, Yichun

2015-09-01

A simple top electrode preparation process, employing continuous graphene oxide films as electrode supporting layers, was adopted to fabricate a ZnO nanorod array/p-GaN heterojunction LED. The achieved LED demonstrated different electroluminescence behaviors under forward and reverse biases: a yellow-red emission band was observed under forward bias, whereas a blue-UV emission peak was obtained under reverse bias. Electroluminescence spectra under different currents and temperatures, as well as heterojunction energy-band alignments, reveal that the yellow-red emission under forward bias originates from recombinations related to heterointerface defects, whereas the blue-UV electroluminescence under reverse bias is ascribed to transitions from near-band-edge and Mg-acceptor levels in p-GaN.

Color-tunable electrophosphorescent device fabricated by a photo-bleaching method

International Nuclear Information System (INIS)

Kim, Tae-Ho; Park, Jong Hyeok; Park, O Ok

2011-01-01

We demonstrated an efficient color-tunable electrophosphorescent device fabricated by a photo-bleaching method. Electroluminescence studies indicate that excellent device performance can be achieved through efficient Foerster energy transfer from the conjugated polymer to the iridium complexes by improving their miscibility. The use of a very low concentration of red phosphorescent dye and the easy degradation characteristics of conjugated structure of the red dopant enable color-tuning from red to green emission by a simple UV-irradiation process without a sacrifice of luminescent properties.tp

Far-field self-focusing and -defocusing radiation behaviors of the electroluminescent light sources due to negative refraction.

Science.gov (United States)

Yin, Yu-Feng; Lin, Yen-Chen; Tsai, Tsung-Han; Shen, Yi-Chun; Huang, Jianjang

2013-01-15

In recent years, researchers have demonstrated negative refraction theoretically and experimentally by pumping optical power into photonic crystal (PhC) or waveguide structures. The concept of negative refraction can be used to create a perfect lens that focuses an object smaller than the wavelength. By inserting two-dimensional PhCs into the peripheral of a semiconductor light emitting structure, this study presents an electroluminescent device with negative refraction in the visible wavelength range. This approach produces polarization dependent collimation behavior in far-field radiation patterns. The modal dispersion of negative refraction results in strong group velocity modulation, and self-focusing and -defocusing behaviors are apparent from light extraction. This study further verifies experimental results by using theoretic calculations based on equifrequency contours.

Spectrally resolved hyperfine interactions between polaron and nuclear spins in organic light emitting diodes: Magneto-electroluminescence studies

Energy Technology Data Exchange (ETDEWEB)

Crooker, S. A.; Kelley, M. R.; Martinez, N. J. D.; Nie, W.; Mohite, A.; Nayyar, I. H.; Tretiak, S.; Smith, D. L. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Liu, F.; Ruden, P. P. [University of Minnesota, Minneapolis, Minnesota 55455 (United States)

2014-10-13

We use spectrally resolved magneto-electroluminescence (EL) measurements to study the energy dependence of hyperfine interactions between polaron and nuclear spins in organic light-emitting diodes. Using layered devices that generate bright exciplex emission, we show that the increase in EL emission intensity I due to small applied magnetic fields of order 100 mT is markedly larger at the high-energy blue end of the EL spectrum (ΔI/I ∼ 11%) than at the low-energy red end (∼4%). Concurrently, the widths of the magneto-EL curves increase monotonically from blue to red, revealing an increasing hyperfine coupling between polarons and nuclei and directly providing insight into the energy-dependent spatial extent and localization of polarons.

Electroluminescence analysis for spatial characterization of parasitic optical losses in silicon heterojunction solar cells

Science.gov (United States)

Ahmed, Nuha; Zhang, Lei; Sriramagiri, Gowri; Das, Ujjwal; Hegedus, Steven

2018-04-01

Electroluminescence (EL) coupled with reflection measurements are used to spatially quantify optical losses in silicon heterojunction solar cells due to plasmonic absorption in the metal back contacts. The effect of indium tin oxide back reflector in decreasing this plasmonic absorption is found to increase the reflection from the back nickel (Ni)-aluminum (Al) and Al metals by ˜12% and ˜41%, respectively, in both bifacial and front junction silicon solar cells. Losses due to back reflection are calculated by comparison between the EL emission signals in high and low back reflection samples and are shown to be in agreement with standard reflection measurements. We conclude that the optical properties of the back contact can significantly influence the EL intensity which complicates the interpretation of EL as being primarily due to recombination especially when comparing two different devices with spatially varying back surface structures.

Self-scaling minority carrier lifetime imaging using periodically modulated electroluminescence

Science.gov (United States)

Kropp, Timo; Berner, Marcel; Werner, Jürgen H.

2017-11-01

We present a straightforward self-scaling imaging technique to extract the effective minority carrier lifetime image of silicon solar cells using periodically modulated electroluminescence. This novel modulation technique overcomes main limiting factors linked to camera integration time. Our approach is based on comparing three luminescence images taken during current modulation. One image is taken while periodically injecting excess charge carriers with a pulsed current stimulation followed by an open-circuit luminescence decay. A second image with the same injection profile is taken while additionally extracting excess charge carriers at the falling edge, accelerating the luminescence decay. Both images are normalized to a steady-state image. The camera integration time is several orders of magnitude longer than the modulation period length, and no synchronization of image acquisition is needed. The intensity difference between both modulated images is used for determining a calibration factor to convert the steady-state image into the effective minority carrier lifetime image: Our modulation method enables carrier lifetime images completely independent of the image integration time. First carrier lifetime images show good agreement with data from time resolved electroluminescence.

Enhanced electroluminescence of organic light-emitting diodes by using halloysite nanotubes

Energy Technology Data Exchange (ETDEWEB)

Mondragón, Margarita, E-mail: mmondragon@ipn.mx [Instituto Politécnico Nacional, ESIME Azcapotzalco, Av. de las Granjas 682, 02250 México D.F. (Mexico); Moggio, Ivana; León, Arxel de; Arias, Eduardo [Centro de Investigación en Química Aplicada, CIQA, Blvd. Enrique Reyna 140, 25253 Saltillo, Coahuila (Mexico)

2013-12-15

The effect of halloysite clay nanotubes (HNTs) on the optical and electronic properties of poly(2-methoxy-5-[2′-ethylhexyloxy]-1,4-phenylenevinylene) (MEH-PPV) have been investigated. The UV–vis absorption band of the conjugated polymer remains unchanged upon the incorporation of halloysite nanotubes (HNTs). Photoluminescence (PL) measurements reveal a decreased quantum yield in the MEH-PPV/HNTs nanocomposites, compared with bulk MEH-PPV. Improvement of the electroluminescence of organic light-emitting diodes (OLEDs) was achieved by incorporating high contents of HNTs. The nanotubes act to enhanced polymer aggregates, as revealed by AFM analysis, thus increasing charge transport and therefore electroluminescence but also decreasing PL quantum yield. -- Highlights: • Thin films of nanocomposites of MEH-PPV/HNTs were prepared by spin coating. • Quantum yield in the nanocomposites was decreased compared with bulk MEH-PPV. • Improvement of the EL of OLEDs was achieved by incorporating high contents of HNTs. • The HNTs act to enhanced polymer aggregates, as revealed by AFM.

Enhanced electroluminescence of organic light-emitting diodes by using halloysite nanotubes

International Nuclear Information System (INIS)

Mondragón, Margarita; Moggio, Ivana; León, Arxel de; Arias, Eduardo

2013-01-01

The effect of halloysite clay nanotubes (HNTs) on the optical and electronic properties of poly(2-methoxy-5-[2′-ethylhexyloxy]-1,4-phenylenevinylene) (MEH-PPV) have been investigated. The UV–vis absorption band of the conjugated polymer remains unchanged upon the incorporation of halloysite nanotubes (HNTs). Photoluminescence (PL) measurements reveal a decreased quantum yield in the MEH-PPV/HNTs nanocomposites, compared with bulk MEH-PPV. Improvement of the electroluminescence of organic light-emitting diodes (OLEDs) was achieved by incorporating high contents of HNTs. The nanotubes act to enhanced polymer aggregates, as revealed by AFM analysis, thus increasing charge transport and therefore electroluminescence but also decreasing PL quantum yield. -- Highlights: • Thin films of nanocomposites of MEH-PPV/HNTs were prepared by spin coating. • Quantum yield in the nanocomposites was decreased compared with bulk MEH-PPV. • Improvement of the EL of OLEDs was achieved by incorporating high contents of HNTs. • The HNTs act to enhanced polymer aggregates, as revealed by AFM

Aftereffect of UV excitation on the ZnS electroluminescent emission

International Nuclear Information System (INIS)

Maxia, V.; Muntoni, C.; Murgia, M.

1980-01-01

The initial a.c. electroluminescent (EL) emission of ZnS(Cu) previously excited with UV light has been studied. The experiments showed that the EL build-up is made more swift by the preceding UV excitation. This result is ascribed to space charge produced by UV excitation which affects the exchange of electrons between lattice and EL defects. (author)

Change of the dominant luminescent mechanism with increasing current density in molecularly doped organic light-emitting devices

International Nuclear Information System (INIS)

Zhou Liang; Zhang Hongjie; Meng Qingguo; Liu Fengyi; Yu Jiangbo; Deng Ruiping; Peng Zeping; Li Zhefeng; Guo Zhiyong

2007-01-01

We have fabricated and measured a series of electroluminescent devices with the structure of ITO/TPD/Eu(TTA) 3 phen (x):CBP/BCP/ALQ/LiF/Al, where x is the weight percentage of Eu(TTA) 3 phen (from 0% to 6%). At very low current density, carrier trapping is the dominant luminescent mechanism and the 4% doped device shows the highest electroluminescence (EL) efficiency among all these devices. With increasing current density, Foerster energy transfer participates in EL process. At the current density of 10.0 and 80.0 mA/cm 2 , 2% and 3% doped devices show the highest EL efficiency, respectively. From analysis of the EL spectra and the EL efficiency-current density characteristics, we found that the EL efficiency is manipulated by Foerster energy transfer efficiency at high current density. So we suggest that the dominant luminescent mechanism changes gradually from carrier trapping to Foerster energy transfer with increasing current density. Moreover, the conversion of dominant EL mechanism was suspected to be partly responsible for the EL efficiency roll-off because of the lower EL quantum efficiency of Foerster energy transfer compared with carrier trapping

Molecular structure, photoluminescent and electroluminescent properties of bis(2-(4-methyl-2-hydroxyphenyl)benzothiazolate) zinc with excellent electron-transport characteristics

International Nuclear Information System (INIS)

Xu Huixia; Xu Bingshe; Fang Xiaohong; Yue Yan; Chen Liuqing; Wang Hua; Hao Yuying

2011-01-01

Highlights: → The synthesis, crystal structure and photophysical properties of Zn(4-MeBTZ) 2 were reported. → The electron-transport property was investigated by theoretical calculations and experimental. → We found that Zn(4-MeBTZ) 2 has a higher electron mobility than that of [Zn(BTZ) 2 ] 2 and the devices based on it have a lower turn-on voltage. - Abstract: In this article, the molecular structure, photoluminescent and electroluminescent properties of bis(2-(4-methyl-2-hydroxyphenyl) benzothiazolate) zinc (Zn(4-MeBTZ) 2 ) with good electron-transport characteristics were reported. This complex was identified as triclinic structure with the strong intermolecular π-π stacking interactions between the benzothiazolate/phenoxido rings and weak intramolecular hydrogen bonds by X-ray single-crystal diffraction. Quantum chemical method has been employed to investigate electron structure and charge transport property. The blue-green light emission was observed by fabricating double-layer devices using Zn(4-MeBTZ) 2 as electron-transport and NPB as hole-transport material. The performance of organic light-emitting devices based on Zn(4-MeBTZ) 2 is much better than that of the devices based on [Zn(BTZ) 2 ] 2 .

Synthesis and electroluminescence characterization of a new aluminum complex, [8-hydroxyquinoline] bis [2, 2'bipyridine] aluminum Al(Bpy)2q

Science.gov (United States)

Rahul, Kumar; Ritu, Srivastava; Punita, Singh

2016-01-01

We have synthesized and characterized a new electroluminescent material, [8-hydroxyquinoline] bis [2,2'bipyridine] aluminum. A solution of this material Al(Bpy)2q in toluene showed absorption maxima at 380 nm, which was attributed to the moderate energy (π-π*) transitions of the aromatic rings. The photoluminescence spectrum of Al(Bpy)2q in the toluene solution showed a peak at 518 nm. This material shows thermal stability up to 300 °C. The structure of the device is ITO/F4-TCNQ (1 nm)/α-NPD (35 nm)/Al(Bpy)2q (35 nm)/ BCP (6 nm)/Alq3 (28 nm)/LiF (1 nm)/Al (150 nm). This device exhibited a luminescence peak at 515 nm (CIE coordinates, x = 0.32, y = 0.49). The maximum luminescence of the device was 214 cd/m2 at 21 V. The maximum current efficiency of OLED was 0.12 cd/A at 13 V and the maximum power efficiency was 0.03 lm/W at 10 V.

Photo/electroluminescence properties of an europium (III) complex doped in 4,4'-N,N'-dicarbazole-biphenyl matrix

International Nuclear Information System (INIS)

Zhou Yonghui; Zhou Liang; Wu, Jing; Li, Hong-Yan; Zheng Youxuan; You Xiaozeng; Zhang Hongjie

2010-01-01

The photoluminescence properties of one europium complex Eu(TFNB) 3 Phen (TFNB = 4,4,4-trifluoro-1-(naphthyl)-1,3-butanedione, Phen = 1,10-phenanthroline) doped in a hole-transporting material CBP (4,4'-N,N'-dicarbazole-biphenyl) films were studied. A series of organic light-emitting devices (OLEDs) using Eu(TFNB) 3 Phen as the emitter were fabricated with a multilayer structure of indium tin oxide, 250 Ω/square)/TPD (N,N'-diphenyl-N,N'-bis(3-methyllphenyl)-(1,1'-biphenyl)-4,4'-diamine, 50 nm)/Eu(TFNB) 3 phen (x): CBP (4,4'-N,N'-dicarbazole-biphenyl, 45 nm)/BCP (2,9-dimethyl-4,7-diphenyl-l,10 phenanthroline, 20 nm)/AlQ (tris(8-hydroxy-quinoline) aluminium, 30 nm)/LiF (1 nm)/Al (100 nm), where x is the weight percentage of Eu(TFNB) 3 phen doped in the CBP matrix (1-6%). A red emission at 612 nm with a half bandwidth of 3 nm, characteristic of Eu(III) ion, was observed with all devices. The device with a 3% dopant concentration shows the maximum luminance up to 1169 cd/m 2 (18 V) and the device with a 5% dopant concentration exhibits a current efficiency of 4.46 cd/A and power efficiency of 2.03 lm/W. The mechanism of the electroluminescence was also discussed.

Electroluminescence and rectifying properties of heterojunction LEDs based on ZnO nanorods

International Nuclear Information System (INIS)

Rout, Chandra Sekhar; Rao, C N R

2008-01-01

n-ZnO NR/p-Si and n-ZnO NR/p-PEDOT/PSS heterojunction light-emitting diodes (LEDs) have been fabricated with ZnO nanorods (NRs) grown by a low-temperature method as well as by employing pulsed laser deposition (PLD). The low-temperature method involves growing the ZnO nanorods by the reaction of water with zinc metal. The current-voltage (I-V) characteristics of the heterojunctions show good rectifying diode characteristics. The electroluminescence (EL) spectra of the nanorods show an emission band at around 390 nm and defect related bands in the 400-550 nm region. Room-temperature electroluminescence is detected under forward bias for both the heterostructures. With the low-temperature grown nanorods, the defect related bands in the 400-550 nm range are more intense in the EL spectra, whereas with the PLD grown nanorods, only the 390 nm band is prominent

Electroluminescent Characteristics of DBPPV–ZnO Nanocomposite Polymer Light Emitting Devices

Directory of Open Access Journals (Sweden)

Madhava Rao MV

2009-01-01

Full Text Available Abstract We have demonstrated that fabrication and characterization of nanocomposite polymer light emitting devices with metal Zinc Oxide (ZnO nanoparticles and 2,3-dibutoxy-1,4-poly(phenylenevinylene (DBPPV. The current and luminance characteristics of devices with ZnO nanoparticles are much better than those of device with pure DBPPV. Optimized maximum luminance efficiencies of DBPPV–ZnO (3:1 wt% before annealing (1.78 cd/A and after annealing (2.45 cd/A having a brightness 643 and 776 cd/m2at a current density of 36.16 and 31.67 mA/cm2are observed, respectively. Current density–voltage and brightness–voltage characteristics indicate that addition of ZnO nanoparticles can facilitate electrical injection and charge transport. The thermal annealing is thought to result in the formation of an interfacial layer between emissive polymer film and cathode.

Room-temperature electroluminescence of Er-doped hydrogenated amorphous silicon

Energy Technology Data Exchange (ETDEWEB)

Gusev, Oleg; Bresler, Mikhail; Kuznetsov, Alexey; Kudoyarova, Vera; Pak, Petr; Terukov, Evgenii; Tsendin, Konstantin; Yassievich, Irina [A F Ioffe Physico-Technical Institute, Politekhnicheskaya 26, 194021 St. Petersburg (Russian Federation); Fuhs, Walther [Hahn-Meitner Institut, Abteilung Photovoltaik, Rudower Chaussee 5, D-12489 Berlin (Germany); Weiser, Gerhard [Phillips-Universitat Marburg, Fachbereich Physik, D-35032 Marburg (Germany)

1998-05-11

We have observed room-temperature erbium-ion electroluminescence in erbium-doped amorphous silicon. Electrical conduction through the structure is controlled by thermally activated ionization of deep D{sup -} defects in an electric field and the reverse process of capture of mobile electrons by D{sup 0} states. Defect-related Auger excitation (DRAE) is responsible for excitation of erbium ions located close to dangling-bond defects. Our experimental data are consistent with the mechanisms proposed

Radiation emitter-detector package

International Nuclear Information System (INIS)

O'Brien, J.T.; Limm, A.C.; Nyul, P.; Tassia, V.S. Jr.

1978-01-01

Mounted on the metallic base of a radiation emitter-detector is a mounting block is a first projection, and a second projection. A radiation detector is on the first projection and a semiconductor electroluminescent device, i.e., a radiation emitter, is on the second projection such that the plane of the recombination region of the electroluminescent device is perpendicular to the radiation incident surface of the radiation detector. The electroluminescent device has a primary emission and a secondary emission in a direction different from the primary emission. A radiation emitter-detector package as described is ideally suited to those applications wherein the secondary radiation of the electroluminescent device is fed into a feedback circuit regulating the biasing current of the electroluminescent device

Synthesis and electroluminescence characterization of a new aluminum complex, [8-hydroxyquinoline] bis [2, 2'bipyridine] aluminum Al(Bpy)2q

International Nuclear Information System (INIS)

Rahul, Kumar; Ritu, Srivastava; Punita, Singh

2016-01-01

We have synthesized and characterized a new electroluminescent material, [8-hydroxyquinoline] bis [2,2'bipyridine] aluminum. A solution of this material Al(Bpy) 2 q in toluene showed absorption maxima at 380 nm, which was attributed to the moderate energy (π–π*) transitions of the aromatic rings. The photoluminescence spectrum of Al(Bpy) 2 q in the toluene solution showed a peak at 518 nm. This material shows thermal stability up to 300 °C. The structure of the device is ITO/F4-TCNQ (1 nm)/α-NPD (35 nm)/Al(Bpy) 2 q (35 nm)/ BCP (6 nm)/Alq 3 (28 nm)/LiF (1 nm)/Al (150 nm). This device exhibited a luminescence peak at 515 nm (CIE coordinates, x = 0.32, y = 0.49). The maximum luminescence of the device was 214 cd/m 2 at 21 V. The maximum current efficiency of OLED was 0.12 cd/A at 13 V and the maximum power efficiency was 0.03 lm/W at 10 V. (paper)

Quantitative Prediction of Power Loss for Damaged Photovoltaic Modules Using Electroluminescence

Directory of Open Access Journals (Sweden)

Timo Kropp

2018-05-01

Full Text Available Electroluminescence (EL is a powerful tool for the qualitative mapping of the electronic properties of solar modules, where electronic and electrical defects are easily detected. However, a direct quantitative prediction of electrical module performance purely based on electroluminescence images has yet to be accomplished. Our novel approach, called “EL power prediction of modules” (ELMO as presented here, used just two electroluminescence images to predict the electrical loss of mechanically damaged modules when compared to their original (data sheet power. First, using this method, two EL images taken at different excitation currents were converted into locally resolved (relative series resistance images. From the known, total applied voltage to the module, we were then able to calculate absolute series resistance values and the real distribution of voltages and currents. Then, we reconstructed the complete current/voltage curve of the damaged module. We experimentally validated and confirmed the simulation model via the characterization of a commercially available photovoltaic module containing 60 multicrystalline silicon cells, which were mechanically damaged by hail. Deviation between the directly measured and predicted current/voltage curve was less than 4.3% at the maximum power point. For multiple modules of the same type, the level of error dropped below 1% by calibrating the simulation. We approximated the ideality factor from a module with a known current/voltage curve and then expand the application to modules of the same type. In addition to yielding series resistance mapping, our new ELMO method was also capable of yielding parallel resistance mapping. We analyzed the electrical properties of a commercially available module, containing 72 monocrystalline high-efficiency back contact solar cells, which suffered from potential induced degradation. For this module, we predicted electrical performance with an accuracy of better

Efficient light-emitting devices based on platinum-complexes-anchored polyhedral oligomeric silsesquioxane materials

KAUST Repository

Yang, Xiaohui

2010-08-24

The synthesis, photophysical, and electrochemical characterization of macromolecules, consisting of an emissive platinum complex and carbazole moieties covalently attached to a polyhedral oligomeric silsesquioxane (POSS) core, is reported. Organic light-emitting devices based on these POSS materials exhibit a peak external quantum efficiency of ca. 8%, which is significantly higher than that of the analogous devices with a physical blend of the platinum complexes and a polymer matrix, and they represent noticeable improvement in the device efficiency of solution-processable phosphorescent excimer devices. Furthermore, the ratio of monomer and excimer/aggregate electroluminescent emission intensity, as well as the device efficiency, increases as the platinum complex moiety presence on the POSS macromolecules decreases. © 2010 American Chemical Society.

Investigating side chain mediated electroluminescence from carbazole-modified polyfluorene.

Science.gov (United States)

Liao, Jin-Long; Chen, Xiwen; Liu, Ching-Yang; Chen, Show-An; Su, Chiu-Huen; Su, An-Chung

2007-09-06

In molecular design of electroluminescent (EL) conjugated polymers, introducing a charge transport moiety on a side chain is found to be a promising method for balancing electron and hole fluxes in EL devices without changing the emitting color if there is no interaction between moiety and main chain. In the case of grafting a carbazole (Cz) moiety (hole transporting) on blue emitting polyfluorene, a green emission appears with intensity comparable to the blue emission, which was attributed to a possible interaction between main chain and Cz as previously reported by us. Here, a detailed study of its EL mechanism was carried out by means of time-resolved EL with the assistance of molecular simulation and thermally stimulated current measurements; exploration of how main chain segments interact with the transport moiety was performed. We found the Cz groups in Cz100PF play multiple roles: they act as (1) hole transporter to improve hole injection, (2) hole trapping site for efficient electron-hole recombination to yield blue-emitting excitons, and (3) source of green emission from electroplex formed via electric field-mediated interaction of the Cz/Cz radical cation with an electron in the nearby PF backbone. In combination, these observations suggest that integrated consideration for both intramolecular and intermolecular interactions provides a new route of molecular design of efficient EL polymers.

Comparison of the electroluminescence of a red fluorescent dye doped into the Alq{sub 3} and Alq{sub 3}:rubrene mixed host

Energy Technology Data Exchange (ETDEWEB)

Kang, Hee-Young; Kang, Gi-Wook; Park, Kyung-Min; Yoo, In-Sun; Lee, Changhee

2004-01-05

We studied the effect of a mixed host of Alq{sub 3} and rubrene on the energy transfer and charge trapping processes in organic light-emitting devices with a red fluorescent dopant of 4-(dicyanomethylene)-2-tert-butyl-6 (1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB). The temperature dependence of electroluminescence (EL) properties is compared for the device with DCJTB doped into the Alq{sub 3} only host and that with the Alq{sub 3}:rubrene mixed host. The device with the Alq{sub 3}:rubrene mixed host shows an efficient red emission from DCJTB, negligible EL emission from Alq{sub 3}, and a lower EL drive voltage compared to the device with the Alq{sub 3} only host. Upon cooling the device temperature, the EL emission from rubrene increases but the emission from Alq{sub 3} is still weak, and the quantum efficiency (QE) is almost temperature-independent for the device with the Alq{sub 3}:rubrene mixed host. On the contrary, the EL emission from Alq{sub 3} increases and the QE decreases for devices with the Alq{sub 3} only host at low temperature. The results indicate that recombination of injected electrons and holes occurs on rubrene and subsequent energy transfer to DCJTB dominates in the device with the Alq{sub 3}:rubrene mixed host.

The influence of charge injection from intermediate connectors on the performance of tandem organic light-emitting devices

Energy Technology Data Exchange (ETDEWEB)

Zhou, Dong-Ying [Institute of Functional Nano and Soft Materials (FUNSOM), Soochow University, Suzhou, Jiangsu 215123 (China); Department of Electrical and Computer Engineering and Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, Ontario N2L 3G1 (Canada); Siboni, Hossein Zamani; Wang, Qi; Aziz, Hany, E-mail: lsliao@suda.edu.cn, E-mail: h2aziz@uwaterloo.ca [Department of Electrical and Computer Engineering and Waterloo Institute for Nanotechnology, University of Waterloo, 200 University Avenue West, Waterloo, Ontario N2L 3G1 (Canada); Liao, Liang-Sheng, E-mail: lsliao@suda.edu.cn, E-mail: h2aziz@uwaterloo.ca [Institute of Functional Nano and Soft Materials (FUNSOM), Soochow University, Suzhou, Jiangsu 215123 (China)

2014-12-14

Charge generation in a typical intermediate connector, composed of “n-type doped layer/transition metal oxide (TMO)/hole transporting layer (HTL),” of a tandem organic light-emitting device (OLED) has recently been found to arise from charge transfer at the TMO/HTL interfaces. In this paper, we investigate the effect of hole injection barriers from intermediate connectors on the performance of tandem OLEDs. The hole injection barriers are caused by the offset of the highest occupied molecular orbital (HOMO) energy levels between HTLs contained in the intermediate connector and the top electroluminescence (EL) unit. We also find that although charge generation can occur at the interfaces between the TMO and a wide variety of HTLs of different HOMO values, an increase in the hole injection barrier however limits the electroluminescence efficiency of the top EL units. In the case of large hole injection barriers, significant charge accumulation in the HTLs makes the intermediate connector lose its functionality gradually over operating time, and limits device stability.

Large magneto-conductance and magneto-electroluminescence in exciplex-based organic light-emitting diodes at room temperature

Science.gov (United States)

Ling, Yongzhou; Lei, Yanlian; Zhang, Qiaoming; Chen, Lixiang; Song, Qunliang; Xiong, Zuhong

2015-11-01

In this work, we report on large magneto-conductance (MC) over 60% and magneto-electroluminescence (MEL) as high as 112% at room temperature in an exciplex-based organic light-emitting diode (OLED) with efficient reverse intersystem crossing (ISC). The large MC and MEL are individually confirmed by the current density-voltage characteristics and the electroluminescence spectra under various magnetic fields. We proposed that this type of magnetic field effect (MFE) is governed by the field-modulated reverse ISC between the singlet and triplet exciplex. The temperature-dependent MFEs reveal that the small activation energy of reverse ISC accounts for the large MFEs in the present exciplex-based OLEDs.

Electroluminescent drift chamber with 16 μm spatial resolution

International Nuclear Information System (INIS)

Baskakov, V.I.; Dolgoshein, V.A.; Lebedenko, V.N.

1978-01-01

Studied are the characteristics of the dft electroluminscent chamber of an original design. For insuring high spatial resolution, the chamber has been filled with xenon to a pressure of 20 atm, which substantially decreases the electron diffusion during drift. Located at the end of the drift gap is an anode wire, 50 μm in dia. A strong electric field available near the thin wire causes electroluminescence of the electrons. The signal is localized within a small volume and contribution of the luminescence time in the total duration of a signal is small. In this case no electron multiplication occurs at all and, consequently, no space charge of positive ions takes place, which makes it possible to operate at very high loadings (2x10 6 particle/s). The characteristics of the chamber are measured in a beam of the Serpukhov accelerator. Use has been made of a model comprising two chambers, 5 mm thick, located successively along the beam with the effective area being 40x40 mm. The studies and analysis performed reveal that the drift electroluminescent chamber operates reliably in the wide range of the working gas pressure at an intensity of the incident particles up to 10 5 particle/s. The best resolution is obtained at a pressure of 20 atm and it equals 16 μm

Two-phase xenon detector with gas amplification and electroluminescent signal detection

International Nuclear Information System (INIS)

Akimov, D.Yu.; Burenkov, A.A.; Grishkin, Yu.L.; Kovalenko, A.G.; Lebedenko, V.N.; Stekhanov, V.N.

2008-01-01

An optical technique for detecting ionization electrons produced during ionization of the liquid phase has been experimentally tested in two-phase (liquid-gas) xenon. The effects of gas and electroluminescent amplifications at the wire anode are simultaneously used for detection. This method allows construction of a supersensitive detector of small ionization signals-down to those corresponding to the detection of single electrons [ru

Role of the inversion layer on the charge injection in silicon nanocrystal multilayered light emitting devices

Energy Technology Data Exchange (ETDEWEB)

Tondini, S. [Nanoscience Laboratory, Department of Physics, University of Trento, Via Sommarive 14, 38123 Trento (Italy); Dipartimento di Fisica, Informatica e Matematica, Università di Modena e Reggio Emilia, Via Campi 213/a, 41125 Modena (Italy); Pucker, G. [Advanced Photonics and Photovoltaics Group, Bruno Kessler Foundation, Via Sommarive 18, 38123 Trento (Italy); Pavesi, L. [Nanoscience Laboratory, Department of Physics, University of Trento, Via Sommarive 14, 38123 Trento (Italy)

2016-09-07

The role of the inversion layer on injection and recombination phenomena in light emitting diodes (LEDs) is here studied on a multilayer (ML) structure of silicon nanocrystals (Si-NCs) embedded in SiO{sub 2}. Two Si-NC LEDs, which are similar for the active material but different in the fabrication process, elucidate the role of the non-radiative recombination rates at the ML/substrate interface. By studying current- and capacitance-voltage characteristics as well as electroluminescence spectra and time-resolved electroluminescence under pulsed and alternating bias pumping scheme in both the devices, we are able to ascribe the different experimental results to an efficient or inefficient minority carrier (electron) supply by the p-type substrate in the metal oxide semiconductor LEDs.

Study of electron mobility in small molecular SAlq by transient electroluminescence method

Science.gov (United States)

Kumar, Pankaj; Jain, S. C.; Kumar, Vikram; Chand, Suresh; Kamalasanan, M. N.; Tandon, R. P.

2007-12-01

The study of electron mobility of bis(2-methyl 8-hydroxyquinoline) (triphenyl siloxy) aluminium (SAlq) by transient electroluminescence (EL) is presented. An EL device is fabricated in bilayer, ITO/N,N'-diphenyl-N, N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD)/SAlq/LiF/Al configuration. The temporal evaluation of the EL with respect to the step voltage pulse is characterized by a delay time followed by a fast initial rise, which is followed by a slower rise. The delay time between the applied electrical pulse and the onset of EL is correlated with the carrier mobility (electron in our case). Transient EL studies for SAlq have been carried out at different temperatures and different applied electric fields. The electron mobility in SAlq is found to be field and temperature dependent and calculated to be 6.9 × 10-7 cm2 V-1 s-1 at 2.5 × 106 V cm-1 and 308 K. The EL decays immediately as the voltage is turned off and does not depend on the amplitude of the applied voltage pulse or dc offset.

Electroluminescence and Photoluminescence from a Fluorescent Cobalt Porphyrin Grafted on Graphene Oxide

Science.gov (United States)

Janghouri, Mohammad

2017-10-01

A new graphene oxide-cobalt porphyrin (GO-CoTPP) hybrid material has been used as an emissive layer in organic light-emitting diodes (OLEDs). Devices with fundamental structure of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS, 45 nm)/polyvinylcarbazole (PVK):2-(4-biphenyl)-5-(4- t-butylphenyl)-1,3,4-oxadiazole (PBD):GO-CoTPP (70 nm)/1,3,5-tris( N-phenylbenzimidazol-2-yl)-benzene (TPBI, 20 nm)/Al (150 nm) were fabricated. A red electroluminescence (EL) was obtained from thin-film PVK:PBD:CoTPP at 70 nm thickness. When CoTPP was covalently grafted on graphene oxide (GO) sheets, near-white EL was obtained. The white emission, which was composed of bluish green and red, is attributed to electroplex formation at the GO-CoTPP/PBD interface. Such electroplex emission between electrons and holes is a reason for the low turn-on voltage of the GO-CoTPP-based OLED. Maximum luminance efficiency of 1.43 cd/A with Commission International de l'Eclairage coordinates of 0.33 and 0.40 was achieved at current of 0.02 mA and voltage of 14 V.

Electroluminescence properties of organic light-emitting diodes with a red dye doped into Alq{sub 3} : rubrene mixed host

Energy Technology Data Exchange (ETDEWEB)

Kang, H. Y. [Inha University, Incheon (Korea, Republic of); Lee, C. H. [Seoul National University, Seoul (Korea, Republic of)

2004-09-15

We have studied the electroluminescence (EL) properties of devices with a red fluorescent dye, 4-(dicyanomethylene)-2-t-butyl-6- (1,1,7,7-tetramethyl-julolidyl-9-enyl)--4H-py ran (DCJTB), doped into a mixed matrix of tris-(8-hydroxyquinoline)aluminum (Alq{sub 3}) and rubrene. The devices doped with DCJTB in the Alq{sub 3}:rubrene mixed host show an efficient red emission from DCJTB with negligible EL emission from both Alq{sub 3} and rubrene. The QE increases with increasing rubrene concentration and reaches a maximum of about 3.6 % for a DCJTB doping concentration of about 5 % in the Alq3:rubrene mixed (50:50 % ratio by weight) host, and then decreases at higher rubrene concentration, due to the concentration quenching effect. At a given bias voltage, the current density increases with increasing rubrene doping concentration, but it decreases with increasing DCJTB doping concentration. The results imply that the injected electrons and holes can transport via hopping through the energy levels of rubrene molecules while DCJTB acts as traps.

Applied solid state science advances in materials and device research

CERN Document Server

Wolfe, Raymond

2013-01-01

Applied Solid State Science: Advances in Materials and Device Research, Volume 1 presents articles about junction electroluminescence; metal-insulator-semiconductor (MIS) physics; ion implantation in semiconductors; and electron transport through insulating thin films. The book describes the basic physics of carrier injection; energy transfer and recombination mechanisms; state of the art efficiencies; and future prospects for light emitting diodes. The text then discusses solid state spectroscopy, which is the pair spectra observed in gallium phosphide photoluminescence. The extensive studies

The surface defect-related electroluminescence from the ZnO microwire

Energy Technology Data Exchange (ETDEWEB)

Ding Meng; Zhao Dongxu; Yao Bin; Li Binghui; Zhang Zhenzhong; Shan Chongxin; Shen Dezhen, E-mail: dxzhao2000@yahoo.com.cn [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130021 (China)

2011-02-23

Surface defect-related electroluminescence (EL) was realized from a single ZnO microwire-based metal-semiconductor-metal structure on a glass substrate. ZnO microwires were successfully fabricated using a simple chemical vapour deposition approach. Schottky contacts were detected between Au electrodes and the ZnO microwire. The EL spectrum showed a broad emission band covering the visible range from 400 to 700 nm. The possible EL emission mechanism is discussed in detail in this paper.

Highly efficient red electrophosphorescent devices at high current densities

International Nuclear Information System (INIS)

Wu Youzhi; Zhu Wenqing; Zheng Xinyou; Sun, Runguang; Jiang Xueyin; Zhang Zhilin; Xu Shaohong

2007-01-01

Efficiency decrease at high current densities in red electrophosphorescent devices is drastically restrained compared with that from conventional electrophosphorescent devices by using bis(2-methyl-8-quinolinato)4-phenylphenolate aluminum (BAlq) as a hole and exciton blocker. Ir complex, bis(2-(2'-benzo[4,5-α]thienyl) pyridinato-N,C 3' ) iridium (acetyl-acetonate) is used as an emitter, maximum external quantum efficiency (QE) of 7.0% and luminance of 10000cd/m 2 are obtained. The QE is still as high as 4.1% at higher current density J=100mA/cm 2 . CIE-1931 co-ordinates are 0.672, 0.321. A carrier trapping mechanism is revealed to dominate in the process of electroluminescence

Specific features of electroluminescence in heterostructures with InSb quantum dots in an InAs matrix

Energy Technology Data Exchange (ETDEWEB)

Parkhomenko, Ya. A.; Ivanov, E. V.; Moiseev, K. D., E-mail: mkd@iropt2.ioffe.rssi.ru [Russian Academy of Sciences, Ioffe Physical-Technical Institute (Russian Federation)

2013-11-15

The electrical and electroluminescence properties of a single narrow-gap heterostructure based on a p-n junction in indium arsenide, containing a single layer of InSb quantum dots in the InAs matrix, are studied. The presence of quantum dots has a significant effect on the shape of the reverse branch of the current-voltage characteristic of the heterostructure. Under reverse bias, the room-temperature electroluminescence spectra of the heterostructure with quantum dots, in addition to a negative-luminescence band with a maximum at the wavelength {lambda} = 3.5 {mu}m, contained a positive-luminescence emission band at 3.8 {mu}m, caused by radiative transitions involving localized states of quantum dots at the type-II InSb/InAs heterointerface.

Characterization of UV-enhanced SiPMs for Imaging in High Pressure Xenon Electroluminescent TPC

International Nuclear Information System (INIS)

Yahlali, Nadia; Lorca, David; Fernandes, L.M.P.

2013-06-01

The possibility of recording charged particle tracks in an electro-luminescent xenon gas TPC is investigated using a SiPM-based tracking system, operated in the demonstrator prototype of the NEXT-100 ββ decay experiment. The tracks of the ββ0ν events from the decay of the 136 Xe isotope have a distinctive topology, which allows their discrimination against single-electron events from the natural radioactivity that populates the region of interest of the neutrinoless decay in the ββ energy spectrum. Combined to the near-intrinsic energy resolution of the gaseous detector, this tracking capability provides a powerful background rejection tool for the search of the neutrinoless ββ decay aimed by the experiment. The NEXT-100 detector concepts and sensitivity and the first results of its demonstrator prototype are presented. The characterization studies relevant for the operation of UV-enhanced SiPMs used for imaging in an electro-luminescent TPC are reviewed. (authors)

Structural, morphological and electroluminescence studies of Zno:Co nanophosphor

Science.gov (United States)

Singh, Anju; Vishwakarma, H. L.

2016-09-01

The nanoparticles of zinc oxide (ZnO) doped with various concentrations of cobalt (Co) were synthesized by chemical precipitation method in the presence of capping agent polyvinylpyrrolidone (PVP). The effect of doping concentration on structural and morphological properties has been studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). Cell volume, bond length, texture coefficient, lattice constants and dislocation density are also studied. Here, we also compared the interplaner spacing and relative peak intensities from their standard values with different angles. Crystallite sizes have been calculated by Debye-Scherrer's formula whose values are decreasing with increase in cobalt content up to 3 %. It has been seen that the growth orientation of the prepared ZnO nanorods was (101). The XRD analysis also ensures that ZnO has a hexagonal (wurtzite) crystal structure. The electroluminescence (EL) cells were prepared by placing pure and cobalt-doped ZnO nanoparticles between ITO-coated conducting glass plate and aluminium foil. Alternating voltage of various frequencies was applied, and EL brightness at different voltages was measured and corresponding current was also recorded. The voltage dependence of electroluminescence (EL) brightness of the ZnO:Co shows exponential increase. The linear voltage-current characteristic indicates ohmic nature. The EL brightness at a particular voltage is found to increase by increasing Co doping, but for higher percentage of Co the EL brightness is reduced. It is also seen that Co does not influence the threshold voltage. The brightness is also affected by increasing the frequency of AC signal.

Temperature dependence of electroluminescent emission from (ZnS : Cu, Mn(H)) type luminophors

International Nuclear Information System (INIS)

Singh, L.K.

1986-04-01

The dependence of electroluminescent yield on temperature for hydrogen coactivated (ZnS : Cu, Mn) type triple band emitting phosphors has been investigated at various temperatures under varied operating conditions of excitations. The influence of the excitation frequency, voltage and of emission wavelengths for the electroluminescent characteristics has also been observed on temperature variations. The results have also been studied for temperature dependences of emitting brightness under the excitation by UV-radiations of 3650 A.U. and a comparison is made between temperature dependent characteristics of E.L. and PL-brightness of emissions. It was observed that, as usual, brightness maxima on temperature scale varied with alteration of operating electric fields regarding frequency and voltage both for blue, green and yellow orange emissions of attempted samples. The important thing which is observed here, is that with regards the temperature EL-intensities vary respectively for all respective emissions but emission peaks are not shifted on wave-length scale. This no shift is due to the narrowly and compactly distributed coactivator levels of hydrogen. (author)

High-efficiency red electroluminescent device based on multishelled InP quantum dots.

Science.gov (United States)

Jo, Jung-Ho; Kim, Jong-Hoon; Lee, Ki-Heon; Han, Chang-Yeol; Jang, Eun-Pyo; Do, Young Rag; Yang, Heesun

2016-09-01

We report on the synthesis of highly fluorescent red-emitting InP quantum dots (QDs) and their application to the fabrication of a high-efficiency QD-light-emitting diode (QLED). The core/shell heterostructure of the QDs is elaborately tailored toward a multishelled structure with a composition-gradient ZnSeS intermediate shell and an outer ZnS shell. Using the resulting InP/ZnSeS/ZnS QDs as an emitting layer, all-solution-processible red InP QLEDs are fabricated with a hybrid multilayered device structure having an organic hole transport layer (HTL) and an inorganic ZnO nanoparticle electron transport layer. Two HTLs of poly(9-vinlycarbazole) or poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(4,4'-(N-(4-sec-butylphenyl))diphenyl-amine), whose hole mobilities are different by at least three orders of magnitude, are individually applied for QLED fabrication and such HTL-dependent device performances are compared. Our best red device displays exceptional figures of merit such as a maximum luminance of 2849  cd/m2, a current efficiency of 4.2  cd/A, and an external quantum efficiency of 2.5%.

Synthesis, structures and electroluminescence properties of CdS:In/Si nanoheterostructure array

Energy Technology Data Exchange (ETDEWEB)

Yan, Ling Ling; Cai, Hong Xin; Chen, Liang [Henan Polytechnic University, School of Physics and Electronic Information Engineering, Jiaozuo (China)

2017-10-15

An In-doped CdS/Si nanoheterojunction (CdS:In/Si-NPA) is prepared by depositing an In-doped CdS thin film onto a Si nanoporous pillar array (Si-NPA) via a successive ionic layer adsorption and reaction method. Based on the measured J-V characteristic curve, the nanoheterojunction exhibits a good rectifying behavior with a low forward turn-on voltage (2.2 V), a small leakage current density (0.5 mA/cm{sup 2} at - 3 V) and a high reverse breakdown voltage (> 8 V). The electroluminescence (EL) measurements reveal that a broadband emerges between 400 and 700 nm, and this band is confirmed as a white light emission based on the value of the chromaticity coordinate. The EL properties, including the CIE chromaticity coordinates, Colour Rendering Index and correlated color temperature, can be tuned by the applied voltage. The generation mechanism of the EL can be well interpreted depending on the energy band structure of CdS:In/Si-NPA. The green band should be attributed to the band-edge emission of CdS and the yellow emission may be related to Cd interstitial. These results highlight the potential of CdS:In/Si-NPA as a light source for future white light emitting devices. (orig.)

Bright electroluminescence from a chelate phosphine oxide Eu{sup III} complex with high thermal performance

Energy Technology Data Exchange (ETDEWEB)

Xu Hui [School of Chemistry and Materials, Heilongjiang University, 74 Xuefu Road, Nangang District, Harbin 150080, Heilongjiang Province (China); Institute of Advanced Materials (IAM), Nanjing University of Posts and Telecommunications, 66 Xinmofan Road, Nanjing 21003, Jiangsu Province (China); Yin Kun; Wang Lianhui [Institute of Advanced Materials (IAM), Nanjing University of Posts and Telecommunications, 66 Xinmofan Road, Nanjing 21003, Jiangsu Province (China); Huang Wei [Institute of Advanced Materials (IAM), Fudan University, 220 Handan Road, Shanghai 200433 (China)], E-mail: wei-huang@njupt.edu.cn

2008-10-01

The chelate phosphine oxide ligand 1,8-bis(diphenylphosphino)naphthalene oxide (NaPO) was used to prepare complex 1 tris(2-thenoyltrifluoroacetonate)(1,8-bis(diphenylphosphino)naphthalene oxide)europium(III). The rigid structure of NaPO makes 1 have more compact structure resulting in a temperature of glass transition as high as 147 deg. C, which is the highest in luminescent Eu{sup III} complexes, and a higher decomposition temperature of 349 deg. C. The improvement of carrier transfer ability of NaPO was proved by Gaussian simulation. The multi-layered electroluminescent device based on 1 had a low turn-on voltage of 6.0 V, the maximum brightness of 601 cd m{sup -2} at 21.5 V and 481.4 mA cm{sup -2}, and the excellent voltage-independent spectral stability. These properties demonstrated NaPO cannot only be favorable to form the rigid and compact complex structure, and increase the thermal and morphological stability of the complex, but also reduce the formation of the exciplex.

Single-crystal structure, photophysical characteristics and electroluminescent properties of bis(2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate)zinc

International Nuclear Information System (INIS)

Xu Huixia; Yue, Yan; Wang Hua; Chen Liuqing; Hao Yuying; Xu Bingshe

2012-01-01

In this paper, a zinc (II) complex of Zn 2 (4-tfmBTZ) 4 (4-tfmBTZ=2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate) was reported. Via combination of experimental and theoretical approaches, its molecular structure, photophysical characteristics, electronic structure and electroluminescent properties were investigated. The results indicate that Zn 2 (4-tfmBTZ) 4 exists as five-coordinate geometric structure and two zinc atoms are bridged by oxygen atoms. The intense absorption band was located at 404 nm, which mainly originate from the transition HOMO−1 to LUMO+2. The blue-light emission was observed in tetrahydrofuran solution and thin film. White-light emission with four emission peaks was observed with CIE coordinate of (0.29, 0.33) and a higher CRI of 85.1 by fabricating bilayer device using Zn 2 (4-tfmBTZ) 4 as electron-transport and NPB as hole-transport material. - Highlights: ► The single-crystal and electronic structures of Zn 2 (4-tfmBTZ) 4 . ► The multicolor emission of Zn 2 (4-tfmBTZ) 4 were realized by the simple devices. ► White OLED is achieved with particularly high color rending index (CRI) by the emission of Zn 2 (4-tfmBTZ) 4 .

Improved outcoupling of light in organic light emitting devices, utilizing a holographic DFB-structure

Energy Technology Data Exchange (ETDEWEB)

Reinke, Nils [Organische Funktionsmaterialien, University of Duisburg-Essen (Germany)]. E-mail: nils.reinke@physik.uni-augsburg.de; Fuhrmann, Thomas [Macromolecular Chemistry and Molecular Materials, University of Kassel (Germany); Perschke, Alexandra [Organische Funktionsmaterialien, University of Duisburg-Essen (Germany); Franke, Hilmar [Organische Funktionsmaterialien, University of Duisburg-Essen (Germany)

2004-12-10

In this work organic light emitting devices (OLEDs) were fabricated implementing gratings, in order to extract waveguided electroluminescence (EL). The gratings were recorded by exposing thin films of the molecular azo glass N, N'-bis (4-phenyl)-N, N'-bis [(4-phenylazo)-phenyl] benzidine (AZOPD) to holographic light patterns. The photopatterned AZOPD serves as hole transport material for devices with aluminum-tris(8-hydroxyquinoline) doped with 1% of 4-(dicyanomethylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-pyran (Alq{sub 3}:DCM) as emissive/electron transport layer. The corrugated devices showed enhanced emission in the forward direction. The emitted light is polarized preferably parallel to the grating lines. In addition, we have found a doubling in the total luminance with respect to the unstructured device.

Advanced Optoelectronic Devices based on Si Quantum Dots/Si Nanowires Hetero-structures

International Nuclear Information System (INIS)

Xu, J; Zhai, Y Y; Cao, Y Q; Chen, K J

2017-01-01

Si quantum dots are currently extensively studied since they can be used to develop many kinds of optoelectronic devices. In this report, we review the fabrication of Si quantum dots (Si QD) /Si nanowires (Si NWs) hetero-structures by deposition of Si QDs/SiO 2 or Si QDs/SiC multilayers on Si NWs arrays. The electroluminescence and photovoltaic devices based on the formed hetero-structures have been prepared and the improved performance is confirmed. It is also found that the surface recombination via the surface defects states on the Si NWs, especially the ones obtained by the long-time etching, may deteriorate the device properties though they exhibit the better anti-reflection characteristics. The possible surface passivation approaches are briefly discussed. (paper)

Organic light-emitting devices based on solution-processible quinolato-complex supramolecules

International Nuclear Information System (INIS)

Cheng, J.-A.; Chen, Chin H.; Shieh, H.-P.D.

2009-01-01

This paper discusses a new type of supramolecular material tris{5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinolato} aluminum(III), Al(SCarq) 3 , which we synthesized using three 5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinoline as bidentate ligands. The peak photoluminescence in the solid phase appears at 488 nm. In cyclic voltammetric measurement, two oxidation peaks, which were obtained at -5.6 and -5.9 eV, correspond to HOMO sites of carbazoyl and aluminum quinolates, respectively. In the investigation of solid morphological thin film, the flat surface was investigated using an atomic force microscope. The root mean square (rms) and mean roughness (R a ) were respectively measured to be 0.427 and 0.343 nm. For the fabrication of organic light-emitting devices (OLEDs) using spin-coating techniques, the turn-on voltage and maximum luminescence of the optimized electroluminescence device, glass/ITO (20 nm)/PEDOT:PSS (75 nm)/Al(SCarq) 3 (85 nm)/BCP (8 nm)/LiF (1 nm)/Al (200 nm), were respectively 9.6 V and 35.0 cd m -2 . Due to the electroplex formation between the carbazole (electron-donor) and the aluminum quinolates (electron-acceptor) moieties under an applied DC bias, the chromaticity of electroluminescence shifted to green-yellow with 1931 CIE x,y (0.40, 0.47)

Enhancement of hole injection and electroluminescence by ordered Ag nanodot array on indium tin oxide anode in organic light emitting diode

Energy Technology Data Exchange (ETDEWEB)

Jung, Mi, E-mail: jmnano00@gmail.com, E-mail: Dockha@kist.re.kr [Sensor System Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); School of Mechanical Systems Engineering, Kookmin University, Seoul 136-702 (Korea, Republic of); Mo Yoon, Dang; Kim, Miyoung [Korea Printed Electronics Center, Korea Electronics Technology Institute, Jeollabuk-do, 561-844 (Korea, Republic of); Kim, Chulki; Lee, Taikjin; Hun Kim, Jae; Lee, Seok; Woo, Deokha, E-mail: jmnano00@gmail.com, E-mail: Dockha@kist.re.kr [Sensor System Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Lim, Si-Hyung [School of Mechanical Systems Engineering, Kookmin University, Seoul 136-702 (Korea, Republic of)

2014-07-07

We report the enhancement of hole injection and electroluminescence (EL) in an organic light emitting diode (OLED) with an ordered Ag nanodot array on indium-tin-oxide (ITO) anode. Until now, most researches have focused on the improved performance of OLEDs by plasmonic effects of metal nanoparticles due to the difficulty in fabricating metal nanodot arrays. A well-ordered Ag nanodot array is fabricated on the ITO anode of OLED using the nanoporous alumina as an evaporation mask. The OLED device with Ag nanodot arrays on the ITO anode shows higher current density and EL enhancement than the one without any nano-structure. These results suggest that the Ag nanodot array with the plasmonic effect has potential as one of attractive approaches to enhance the hole injection and EL in the application of the OLEDs.

Exciton-dominant Electroluminescence from a Diode of Monolayer MoS2

Science.gov (United States)

2014-05-14

injected electrons and holes, is a reliable technique to study exciton recombination processes in monolayer MoS2, including val- ley and spin excitation...temperature. After superimposing a white light scattering image of the de - vice, we find that the electroluminescence is localized at the edge of the...We find the emerged feature (labeled NX) peaks at 550 nm with energy of 2.255 eV. In low dimensional system, like monolayer MoS2, Coulomb interactions

Molding resonant energy transfer by colloidal crystal: Dexter transfer and electroluminescence

Science.gov (United States)

González-Urbina, Luis; Kolaric, Branko; Libaers, Wim; Clays, Koen

2010-05-01

Building photonic crystals by combination of colloidal ordering and metal sputtering we were able to construct a system sensitive to an electrical field. In corresponding crystals we embedded the Dexter pair (Ir(ppy3) and BAlq) and investigated the influence of the band gap on the resonant energy transfer when the system is excited by light and by an electric field respectively. Our investigations extend applications of photonic crystals into the field of electroluminescence and LED technologies.

Enhanced quantum efficiency in blue-emitting polymer/dielectric nanolayer nanocomposite light-emitting devices

International Nuclear Information System (INIS)

Park, Jong Hyeok; Lim, Yong Taik; Park, O Ok; Yu, Jae-Woong; Kim, Jai Kyeong; Kim, Young Chul

2004-01-01

Light-emitting devices based on environmentally stable, blue-emitting polymer/dielectric nanolayer nanocomposites were fabricated by blending poly(di-octylfluorene) (PDOF) with organo-clay. By reducing the excimer formation that leads to long wavelength tails, the photoluminescence (PL) and electroluminescence (EL) color purity of the device was enhanced. When a conjugated polymer/dielectric nanolayer nanocomposite is applied to an EL device, we expect an electronic structure similar to the well-known quantum well in small nanodomains. The ratio of PDOF/organo-clay was regulated from 2:1 to 0.5:1 (w/w). The light-emitting device of 0.5:1 (w/w) blend demonstrated the highest quantum efficiency (QE), 0.72% (ph/el), which is ∼500 times higher value compared with that of the pure PDOF layer device. However, the driving voltage of the nanocomposite devices tended to increase with increasing organo-clay content

Electroluminescence Caused by the Transport of Interacting Electrons through Parallel Quantum Dots in a Photon Cavity

Science.gov (United States)

Gudmundsson, Vidar; Abdulla, Nzar Rauf; Sitek, Anna; Goan, Hsi-Sheng; Tang, Chi-Shung; Manolescu, Andrei

2018-02-01

We show that a Rabi-splitting of the states of strongly interacting electrons in parallel quantum dots embedded in a short quantum wire placed in a photon cavity can be produced by either the para- or the dia-magnetic electron-photon interactions when the geometry of the system is properly accounted for and the photon field is tuned close to a resonance with the electron system. We use these two resonances to explore the electroluminescence caused by the transport of electrons through the one- and two-electron ground states of the system and their corresponding conventional and vacuum electroluminescense as the central system is opened up by coupling it to external leads acting as electron reservoirs. Our analysis indicates that high-order electron-photon processes are necessary to adequately construct the cavity-photon dressed electron states needed to describe both types of electroluminescence.

Synthesis, characterization and electroluminescence of two highly-twisted non-doped blue light-emitting materials

Science.gov (United States)

Gong, Xiaojie; Pan, Yipeng; Xie, Xiang; Tong, Tong; Chen, Runfeng; Gao, Deqing

2018-04-01

Two pyrene derivatives, substituted with 2-methylnaphthalene units on 1,3-position and 1,6-position of pyrene backbones, were designed and synthesized. DFT calculation confirmed that the two molecules were highly twisted and the dihedral angles between pyrene backbone and naphthalene unit were over 80°, being attributed to the steric hindrance of ortho-methyl group and the substitution position of pyrene itself. As a result, the intermolecular aggregation was greatly inhibited in the solid state, being beneficial for suppressing the fluorescence quenching. By analyzing the optical and thermal properties, it was found that the π-π conjugation extension could be adjusted and a balance for high fluorescent efficiency and avoiding quenching at the same time could be reached, which may guide the molecular design in the future. The electroluminescence properties of the non-doped devices were enhanced with the double hole-transporting layers by optimizing the energy level matching. The stable blue EL emission, with the Commission Internationaled'Eclairage (CIEx,y) color coordinates of (0.15, 0.13) and (0.15, 0.11) at 7, 8, 9 and 10 V respectively, was obtained.

Solid immersion lenses for enhancing the optical resolution of thermal and electroluminescence mapping of GaN-on-SiC transistors

International Nuclear Information System (INIS)

Pomeroy, J. W.; Kuball, M.

2015-01-01

Solid immersion lenses (SILs) are shown to greatly enhance optical spatial resolution when measuring AlGaN/GaN High Electron Mobility Transistors (HEMTs), taking advantage of the high refractive index of the SiC substrates commonly used for these devices. Solid immersion lenses can be applied to techniques such as electroluminescence emission microscopy and Raman thermography, aiding the development device physics models. Focused ion beam milling is used to fabricate solid immersion lenses in SiC substrates with a numerical aperture of 1.3. A lateral spatial resolution of 300 nm is demonstrated at an emission wavelength of 700 nm, and an axial spatial resolution of 1.7 ± 0.3 μm at a laser wavelength of 532 nm is demonstrated; this is an improvement of 2.5× and 5×, respectively, when compared with a conventional 0.5 numerical aperture objective lens without a SIL. These results highlight the benefit of applying the solid immersion lenses technique to the optical characterization of GaN HEMTs. Further improvements may be gained through aberration compensation and increasing the SIL numerical aperture

Ultraviolet electroluminescence from nitrogen-doped ZnO-based heterojuntion light-emitting diodes prepared by remote plasma in situ atomic layer-doping technique.

Science.gov (United States)

Chien, Jui-Fen; Liao, Hua-Yang; Yu, Sheng-Fu; Lin, Ray-Ming; Shiojiri, Makoto; Shyue, Jing-Jong; Chen, Miin-Jang

2013-01-23

Remote plasma in situ atomic layer doping technique was applied to prepare an n-type nitrogen-doped ZnO (n-ZnO:N) layer upon p-type magnesium-doped GaN (p-GaN:Mg) to fabricate the n-ZnO:N/p-GaN:Mg heterojuntion light-emitting diodes. The room-temperature electroluminescence exhibits a dominant ultraviolet peak at λ ≈ 370 nm from ZnO band-edge emission and suppressed luminescence from GaN, as a result of the decrease in electron concentration in ZnO and reduced electron injection from n-ZnO:N to p-GaN:Mg because of the nitrogen incorporation. The result indicates that the in situ atomic layer doping technique is an effective approach to tailoring the electrical properties of materials in device applications.

Single-crystal structure, photophysical characteristics and electroluminescent properties of bis(2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate)zinc

Energy Technology Data Exchange (ETDEWEB)

Xu Huixia, E-mail: xuhuixia0824@163.com [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Yue, Yan [Department of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China); Wang Hua [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Chen Liuqing [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Hao Yuying [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Department of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China); Xu Bingshe [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China)

2012-04-15

In this paper, a zinc (II) complex of Zn{sub 2}(4-tfmBTZ){sub 4} (4-tfmBTZ=2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate) was reported. Via combination of experimental and theoretical approaches, its molecular structure, photophysical characteristics, electronic structure and electroluminescent properties were investigated. The results indicate that Zn{sub 2}(4-tfmBTZ){sub 4} exists as five-coordinate geometric structure and two zinc atoms are bridged by oxygen atoms. The intense absorption band was located at 404 nm, which mainly originate from the transition HOMO-1 to LUMO+2. The blue-light emission was observed in tetrahydrofuran solution and thin film. White-light emission with four emission peaks was observed with CIE coordinate of (0.29, 0.33) and a higher CRI of 85.1 by fabricating bilayer device using Zn{sub 2}(4-tfmBTZ){sub 4} as electron-transport and NPB as hole-transport material. - Highlights: Black-Right-Pointing-Pointer The single-crystal and electronic structures of Zn{sub 2}(4-tfmBTZ){sub 4}. Black-Right-Pointing-Pointer The multicolor emission of Zn{sub 2}(4-tfmBTZ){sub 4} were realized by the simple devices. Black-Right-Pointing-Pointer White OLED is achieved with particularly high color rending index (CRI) by the emission of Zn{sub 2}(4-tfmBTZ){sub 4}.

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

Science.gov (United States)

de Vos, Marc; Torah, Russel; Tudor, John

2016-04-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps.

First observation of liquid-xenon proportional electroluminescence in THGEM holes

International Nuclear Information System (INIS)

Arazi, L; Itay, R; Landsman, H; Levinson, L; Pasmantirer, B; Rappaport, M L; Vartsky, D; Breskin, A; Coimbra, A E C

2013-01-01

Radiation-induced proportional-electroluminescence UV signals, emitted from the holes of a Thick Gas Electron Multiplier (THGEM) electrode immersed in liquid xenon, were recorded with a PMT for the first time. Significant photon yields were observed with gamma photons and alpha particles using a 0.4 mm thick electrode with 0.3 mm diameter holes; at 2 kV across the THGEM the photon yield was estimated to be ∼ 600 UV photons/electron over 4π. This may pave the way towards the realization of novel single-phase noble-liquid radiation detectors incorporating liquid hole-multipliers (LHM); their concept is presented

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

International Nuclear Information System (INIS)

De Vos, Marc; Torah, Russel; Tudor, John

2016-01-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps. (paper)

Organic light-emitting devices based on solution-processible quinolato-complex supramolecules

Energy Technology Data Exchange (ETDEWEB)

Cheng, J.-A. [Department of Photonics and Display Institute, National Chiao Tung University, Hsinchu 30010, Taiwan (China)], E-mail: jacheng.ac89g@nctu.edu.tw; Chen, Chin H. [Microelectronics and Information System Research Center, National Chiao Tung University, Hsinchu 30010, Taiwan (China); Shieh, H.-P.D. [Department of Photonics and Display Institute, National Chiao Tung University, Hsinchu 30010, Taiwan (China)

2009-02-15

This paper discusses a new type of supramolecular material tris{l_brace}5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinolato{r_brace} aluminum(III), Al(SCarq){sub 3}, which we synthesized using three 5-N-[3-(9H-carbazol-9-yl)propyl]-N-(4-methylphenyl) aminesulfonyl-8-hydroxyquinoline as bidentate ligands. The peak photoluminescence in the solid phase appears at 488 nm. In cyclic voltammetric measurement, two oxidation peaks, which were obtained at -5.6 and -5.9 eV, correspond to HOMO sites of carbazoyl and aluminum quinolates, respectively. In the investigation of solid morphological thin film, the flat surface was investigated using an atomic force microscope. The root mean square (rms) and mean roughness (R{sub a}) were respectively measured to be 0.427 and 0.343 nm. For the fabrication of organic light-emitting devices (OLEDs) using spin-coating techniques, the turn-on voltage and maximum luminescence of the optimized electroluminescence device, glass/ITO (20 nm)/PEDOT:PSS (75 nm)/Al(SCarq){sub 3} (85 nm)/BCP (8 nm)/LiF (1 nm)/Al (200 nm), were respectively 9.6 V and 35.0 cd m{sup -2}. Due to the electroplex formation between the carbazole (electron-donor) and the aluminum quinolates (electron-acceptor) moieties under an applied DC bias, the chromaticity of electroluminescence shifted to green-yellow with 1931 CIE{sub x,y} (0.40, 0.47)

High-efficiency electroluminescence and amplified spontaneous emission from a thermally activated delayed fluorescent near-infrared emitter

Science.gov (United States)

Kim, Dae-Hyeon; D'Aléo, Anthony; Chen, Xian-Kai; Sandanayaka, Atula D. S.; Yao, Dandan; Zhao, Li; Komino, Takeshi; Zaborova, Elena; Canard, Gabriel; Tsuchiya, Youichi; Choi, Eunyoung; Wu, Jeong Weon; Fages, Frédéric; Brédas, Jean-Luc; Ribierre, Jean-Charles; Adachi, Chihaya

2018-02-01

Near-infrared organic light-emitting diodes and semiconductor lasers could benefit a variety of applications including night-vision displays, sensors and information-secured displays. Organic dyes can generate electroluminescence efficiently at visible wavelengths, but organic light-emitting diodes are still underperforming in the near-infrared region. Here, we report thermally activated delayed fluorescent organic light-emitting diodes that operate at near-infrared wavelengths with a maximum external quantum efficiency of nearly 10% using a boron difluoride curcuminoid derivative. As well as an effective upconversion from triplet to singlet excited states due to the non-adiabatic coupling effect, this donor-acceptor-donor compound also exhibits efficient amplified spontaneous emission. By controlling the polarity of the active medium, the maximum emission wavelength of the electroluminescence spectrum can be tuned from 700 to 780 nm. This study represents an important advance in near-infrared organic light-emitting diodes and the design of alternative molecular architectures for photonic applications based on thermally activated delayed fluorescence.

Proximity measuring device with backscattering radiation usable noticeably in remote handling or robotics and related data processing system. Proximetre a rayonnement retrodiffuse utilisable notamment en telemanipulation ou robotique et systeme de traitement associe

Energy Technology Data Exchange (ETDEWEB)

Andre, G; Espiau, B

1985-05-03

The invention is aimed at a proximity measuring device whose emitter, an electroluminescent diode, is controlled by control means to emit short duration (< 10 microseconds), high intensity (> 1A) flashes with periods higher than 100 microseconds. Emetter-object distance can be precisely measured on an 0-30 cm interval with the help of data processing of the response given by the proximity device receiver. This device can be used in remote handling and robotics.

2-(2-Hydroxyphenyl)imidazole-based four-coordinate organoboron compounds with efficient deep blue photoluminescence and electroluminescence.

Science.gov (United States)

Zhang, Zhenyu; Zhang, Zuolun; Zhang, Hongyu; Wang, Yue

2017-12-19

Two new four-coordinate organoboron compounds with 2-(2-hydroxyphenyl)imidazole derivatives as the chelating ligands have been synthesized. They possess high thermal stability and are able to form an amorphous glass state. Crystallographic analyses indicate that the differences in ligand structure cause the change of ππ stacking character. The CH 2 Cl 2 solutions and thin films of these compounds display bright blue emission, and these compounds have appropriate HOMO and LUMO energy levels for carrier injection in OLEDs. By utilizing the good thermal and luminescent properties, as well as the proper frontier orbital energy levels, bright non-doped OLEDs with a simple structure have been realized. Notably, these simple devices show deep blue electroluminescence with the Commission Internationale de l'Éclairage (CIE) coordinate of ca. (0.16, 0.08), which is close to the CIE coordinate of (0.14, 0.08) for standard blue defined by the National Television System Committee. In addition, one of the devices exhibits good performance, showing brightness, current efficiency, power efficiency and external quantum efficiency up to 2692 cd m -2 , 2.50 cd A -1 , 1.81 lm W -1 and 3.63%, respectively. This study not only provides good deep-blue emitting OLED materials that are rarely achieved by using four-coordinate organoboron compounds, but also allows a deeper understanding of the structure-property relationship of 2-(2-hydroxyphenyl)imidazole-based boron complexes, which benefits the further structural design of this type of material.

[A novel yellow organic light-emitting device].

Science.gov (United States)

Ma, Chen; Wang, Hua; Hao, Yu-Ying; Gao, Zhi-Xiang; Zhou, He-Feng; Xu, Bing-She

2008-07-01

The fabrication of a novel organic yellow-light-emitting device using Rhodamine B as dopant with double quantum-well (DQW) structure was introduced in the present article. The structure and thickness of this device is ITO/CuPc (6 nm) /NPB (20 nm) /Alq3 (3 nm)/Alq3 : Rhodamine B (3 nm) /Alq3 (3 nm) /Al q3 : Rhodamine B(3 nm) /Alq3 (30 nm) /Liq (5 nm)/Al (30 nm). With the detailed investigation of electroluminescence of the novel organic yellow-light-emitting device, the authors found that the doping concentration of Rhodamine B (RhB) had a very big influence on luminance and efficiency of the organic yellow-light-emitting device. When doping concentration of Rhodamine B (RhB) was 1.5 wt%, the organic yellow-light-emitting device was obtained with the maximum current efficiency of 1.526 cd x A(-1) and the maximum luminance of 1 309 cd x m(-2). It can be seen from the EL spectra of the devices that there existed energy transferring from Alq3 to RhB in the organic light-emitting layers. When the doping concentration of RhB increased, lambda(max) of EL spectra redshifted obviously. The phenomenon was attributed to the Stokes effect of quantum wells and self-polarization of RhB dye molecules.

Magnetic field effects in hybrid perovskite devices

Science.gov (United States)

Zhang, C.; Sun, D.; Sheng, C.-X.; Zhai, Y. X.; Mielczarek, K.; Zakhidov, A.; Vardeny, Z. V.

2015-05-01

Magnetic field effects have been a successful tool for studying carrier dynamics in organic semiconductors as the weak spin-orbit coupling in these materials gives rise to long spin relaxation times. As the spin-orbit coupling is strong in organic-inorganic hybrid perovskites, which are promising materials for photovoltaic and light-emitting applications, magnetic field effects are expected to be negligible in these optoelectronic devices. We measured significant magneto-photocurrent, magneto-electroluminescence and magneto-photoluminescence responses in hybrid perovskite devices and thin films, where the amplitude and shape are correlated to each other through the electron-hole lifetime, which depends on the perovskite film morphology. We attribute these responses to magnetic-field-induced spin-mixing of the photogenerated electron-hole pairs with different g-factors--the Δg model. We validate this model by measuring large Δg (~ 0.65) using field-induced circularly polarized photoluminescence, and electron-hole pair lifetime using picosecond pump-probe spectroscopy.

Influence of doping location and width of dimethylquinacridone on the performance of organic light emitting devices

International Nuclear Information System (INIS)

Li Jingze; Yahiro, Masayuki; Ishida, Kenji; Matsushige, Kazumi

2005-01-01

The influence of doping location and width of fluorescent dimethylquinacridone (DMQA) molecules on the performance of organic light emitting devices has been systematically investigated. While the doped zone is located at the interface of the hole transport layer (HTL) and the light emitting layer (EML), doping in the HTL leads to significant improvement of the external quantum efficiency relative to the undoped device, whereas the efficiency is lower than that of doping in the EML. This phenomenon is explained according to the electroluminescence (EL) process of the doped DMQA, which is dominated by Foerster energy transfer. Additionally, a device with dual doping in both HTL and EML exhibits the highest efficiency. The EL and photoluminescence spectra are also dependent on the doping sites

Electroluminescence from single-wall carbon nanotube network transistors.

Science.gov (United States)

Adam, E; Aguirre, C M; Marty, L; St-Antoine, B C; Meunier, F; Desjardins, P; Ménard, D; Martel, R

2008-08-01

The electroluminescence (EL) properties from single-wall carbon nanotube network field-effect transistors (NNFETs) and small bundle carbon nanotube field effect transistors (CNFETs) are studied using spectroscopy and imaging in the near-infrared (NIR). At room temperature, NNFETs produce broad (approximately 180 meV) and structured NIR spectra, while they are narrower (approximately 80 meV) for CNFETs. EL emission from NNFETs is located in the vicinity of the minority carrier injecting contact (drain) and the spectrum of the emission is red shifted with respect to the corresponding absorption spectrum. A phenomenological model based on a Fermi-Dirac distribution of carriers in the nanotube network reproduces the spectral features observed. This work supports bipolar (electron-hole) current recombination as the main mechanism of emission and highlights the drastic influence of carrier distribution on the optoelectronic properties of carbon nanotube films.

Synthesis, characterization, photophysics and electroluminescence based on a series of pyran-containing emitters

Energy Technology Data Exchange (ETDEWEB)

Yang Lifen [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Guan Min [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Bian Zuqiang [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China)]. E-mail: bianzq@pku.edu.cn; Xie Junqi [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Chen Tianpeng [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Huang Chunhui [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China)]. E-mail: chhuang@pku.edu.cn

2006-04-03

Four unsymmetric as well as symmetric carbazole or oxadiazole modified pyran-containing compounds have been synthesized and characterized. These compounds are 4-(dicyanomethylene)-2-methyl-6-(4-(carbazolo-9-yl)phenyl)-4H-pyran (10), 4-(dicyanomethylene)-2,6-bis(4-(carbazolo-9-yl)phenyl)-4H-pyran (11), 4-(dicyanomethylene)-2-methyl-6-(4-tert-phenyl)-1,3,4-oxdiazole-4-phenyl)-4 H-pyran (12), and 4-(dicyanomethylene)-2,6-bis(4-tert-phenyl)-1,3, 4-oxdiazole-4-phenyl-4H-pyran (13). Photoluminescent measurements indicated that their maximal emissions can be tuned from 543 to 590 nm in acetone solution. Electroluminescent studies based on these compounds as dopants resulted in greenish yellow light emission. It was found that the device based on the bis-condensed symmetric compound (11) with the configuration of indium tin oxide / Copper (II) phthalocyanine (5 nm) / N,N'-bis-(1-naphthl)-diphenyl-1,1'-biphenyl-4,4'-diamine (40 nm) / compound (11) : tris-(8-quinolinolato)aluminium (Alq{sub 3}) (1%) (30 nm) / 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (5 nm) / Alq{sub 3} (40 nm) / Mg : Ag (9 : 1) (200 nm) / Ag (80 nm) has achieved the highest luminance (6869 cd/m{sup 2}) and efficiency (1.32 lm/W and 2.52 cd/A) among the four emitters.

Study of the electroluminescence of highly stereoregular poly(N-pentenyl-carbazole) for blue and white OLEDs

Science.gov (United States)

Liguori, R.; Botta, A.; Pragliola, S.; Rubino, A.; Venditto, V.; Velardo, A.; Aprano, S.; Maglione, M. G.; Prontera, C. T.; De Girolamo Del Mauro, A.; Fasolino, T.; Minarini, C.

2017-06-01

The electroluminescence (EL) of isotactic and syndiotactic poly(N-pentenyl-carbazole) (PPK), achieved by coordination polymerization, is studied in order to investigate the interrelation between the polymer tacticity and their physical-chemical properties. The use of these polymers in organic light-emitting diode (OLED) fabrication is also explored. Thermal and x-ray diffraction analyses of PPKs show that the isotactic stereoisomer is semicrystalline, whereas the syndiotactic one is amorphous. Optical analysis of both stereoisomers, carried out on film samples, reveals the presence of two different excimers: ‘sandwich-like’ and ‘partially overlapping’. Nevertheless, the emission intensity ratio between ‘sandwich-like’ and ‘partially overlapping’ excimers is higher in the isotactic than in the syndiotactic stereoisomer. Using the synthesized polymers as OLED emitting layers, the influence of the polymer tacticity on the EL properties of the device is highlighted. In detail, while blue OLEDs are obtained by using the syndiotactic stereoisomer, OLEDs with a multilayer structure fabricated with the isotactic stereoisomer emit white light. The contribution of three different emissions (fluorescence, phosphorescence and electromer emissions) with comparable intensities to the detected white light is discussed.

Direct Probing of Carrier Behavior in Electroluminescence Indium-Zinc-Oxide/N,N '-Di-[(1-naphthyl)-N,N '-diphenyl]-(1,1'-biphenyl)-4,4'-diamine/Tris(8-hydroxy-quinolinato)aluminum(III)/LiF/Al Diode by Time-Resolved Optical Second-Harmonic Generation

Science.gov (United States)

Taguchi, Dai; Zhang, Le; Li, Jun; Weis, Martin; Manaka, Takaaki; Iwamoto, Mitsumasa

2011-04-01

By using electric-field-induced second-harmonic generation (EFISHG) measurement, we probed charging and discharging in an α-NPD/Alq3 organic light-emitting diode [α-NPD, N,N '-di-[(1-naphthyl)-N,N '-diphenyl]-(1,1'-biphenyl)-4,4'-diamine; Alq3, tris(8-hydroxy-quinolinato)aluminum(III)] while electroluminescence response was monitored. The EFISHG measurement showed that excessive positive charges accumulated at the α-NPD/Alq3 interface in the charging process, accompanying electroluminescence (EL) radiation, and the accumulated excess positive charges disappeared in the discharging process before the EL decayed. Note that the EL radiation was smooth and strong under the high voltage application, while the EL decayed in a similar way. The Maxwell-Wagner model analysis showed no-dependence of the accumulated excessive positive charge on the applied external voltage, suggesting that electrons and holes injected from the opposite electrodes for EL radiation balanced at the interface. The EFISHG measurement will be useful as a direct way to probe carrier behaviors in organic EL devices.

Magnetically modulated electroluminescence from hybrid organic/inorganic light-emitting diodes based on electron donor-acceptor exciplex blends

Science.gov (United States)

Pang, Zhiyong; Baniya, Sangita; Zhang, Chuang; Sun, Dali; Vardeny, Z. Valy

2016-03-01

We report room temperature magnetically modulated electroluminescence from a hybrid organic/inorganic light-emitting diode (h-OLED), in which an inorganic magnetic tunnel junction (MTJ) with large room temperature magnetoresistance is coupled to an N,N,N ',N '-Tetrakis(4-methoxyphenyl)benzidine (MeO-TPD): tris-[3-(3-pyridyl)mesityl]borane (3TPYMB) [D-A] based OLED that shows thermally activated delayed luminescence. The exciplex-based OLED provides two spin-mixing channels: upper energy channel of polaron pairs and lower energy channel of exciplexes. In operation, the large resistance mismatch between the MTJ and OLED components is suppressed due to the non-linear I-V characteristic of the OLED. This leads to enhanced giant magneto-electroluminescence (MEL) at room temperature. We measured MEL of ~ 75% at ambient conditions. Supported by SAMSUNG Global Research Outreach (GRO) program, and also by the NSF-Material Science & Engineering Center (MRSEC) program at the University of Utah (DMR-1121252).

Electroluminescence of doped and undoped AlN/SiC-heterojunctions

Energy Technology Data Exchange (ETDEWEB)

Bruesewitz, Christoph; Vetter, Ulrich; Hofsaess, Hans [II. Physikalisches Institut, Georg-August-Universitaet Goettingen (Germany)

2010-07-01

AlN with its large and direct bandgap is a useful host for optoelectronic applications. Grown on 6H-SiC, a heterojunction is created, forming a diode. The light emitted by n-doped 6H-SiC via electroluminescence forms a broad band with a maximum at a wavelength of 475 nm. With the AlN layer on the surface, nitrogen atoms can diffuse into the 6H-SiC, creating new energy levels. Depending on the direction of the current and additional dopants in the AlN layer, the carrier concentration changes and new levels are available, resulting in different colours. It is shown that in this heterojunction blue, red and white colours are feasible.

Controlling charge injection in organic electronic devices using self-assembled monolayers

Science.gov (United States)

Campbell, I. H.; Kress, J. D.; Martin, R. L.; Smith, D. L.; Barashkov, N. N.; Ferraris, J. P.

1997-12-01

We demonstrate control and improvement of charge injection in organic electronic devices by utilizing self-assembled monolayers (SAMs) to manipulate the Schottky energy barrier between a metal electrode and the organic electronic material. Hole injection from Cu electrodes into the electroluminescent conjugated polymer poly[2-methoxy,5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] was varied by using two conjugated-thiol based SAMs. The chemically modified electrodes were incorporated in organic diode structures and changes in the metal/polymer Schottky energy barriers and current-voltage characteristics were measured. Decreasing (increasing) the Schottky energy barrier improves (degrades) charge injection into the polymer.

3D Printing of NinjaFlex Filament onto PEDOT:PSS-Coated Textile Fabrics for Electroluminescence Applications

Science.gov (United States)

Tadesse, Melkie Getnet; Dumitrescu, Delia; Loghin, Carmen; Chen, Yan; Wang, Lichuan; Nierstrasz, Vincent

2018-03-01

Electroluminescence (EL) is the property of a semiconductor material pertaining to emitting light in response to an electrical current or a strong electric field. The purpose of this paper is to develop a flexible and lightweight EL device. Thermogravimetric analysis (TGA) was conducted to observe the thermal degradation behavior of NinjaFlex. Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid)—PEDOT:PSS—with ethylene glycol (EG) was coated onto polyester fabric where NinjaFlex was placed onto the coated fabric using three-dimensional (3D) printing and phosphor paste, and BendLay filaments were subsequently coated via 3D printing. Adhesion strength and flexibility of the 3D-printed NinjaFlex on textile fabrics were investigated. The TGA results of the NinjaFlex depict no weight loss up to 150°C and that the NinjaFlex was highly conductive with a surface resistance value of 8.5 ohms/sq.; the coated fabric exhibited a uniform surface appearance as measured and observed by using four-probe measurements and scanning electron microscopy, respectively, at 60% PEDOT:PSS. The results of the adhesion test showed that peel strengths of 4160 N/m and 3840 N/m were recorded for polyester and cotton specimens, respectively. No weight loss was recorded following three washing cycles of NinjaFlex. The bending lengths were increased by only a factor of 0.082 and 0.577 for polyester and cotton samples at 0.1-mm thickness, respectively; this remains sufficiently flexible to be integrated into textiles. The prototype device emitted light with a 12-V alternating current power supply.

Influence of photo-generated carriers on current spreading in double diode structures for electroluminescent cooling

Science.gov (United States)

Radevici, Ivan; Tiira, Jonna; Sadi, Toufik; Oksanen, Jani

2018-05-01

Current crowding close to electrical contacts is a common challenge in all optoelectronic devices containing thin current spreading layers (CSLs). We analyze the effects of current spreading on the operation of the so-called double diode structure (DDS), consisting of a light emitting diode (LED) and a photodiode (PD) fabricated within the same epitaxial growth process, and providing an attractive platform for studying electroluminescent (EL) cooling under high bias conditions. We show that current spreading in the common n-type layer between the LED and the PD can be dramatically improved by the strong optical coupling between the diodes, as the coupling enables a photo-generated current through the PD. This reduces the current in the DDS CSL and enables the study of EL cooling using structures that are not limited by the conventional light extraction challenges encountered in normal LEDs. The current spreading in the structures is studied using optical imaging techniques, electrical measurements, simulations, as well as simple equivalent circuit models developed for this purpose. The improved current spreading leads further to a mutual dependence with the coupling efficiency, which is expected to facilitate the process of optimizing the DDS. We also report a new improved value of 63% for the DDS coupling quantum efficiency.

Printing Smart Designs of Light Emitting Devices with Maintained Textile Properties

Directory of Open Access Journals (Sweden)

Inge Verboven

2018-02-01

Full Text Available To maintain typical textile properties, smart designs of light emitting devices are printed directly onto textile substrates. A first approach shows improved designs for alternating current powder electroluminescence (ACPEL devices. A configuration with the following build-up, starting from the textile substrate, was applied using the screen printing technique: silver (10 µm/barium titanate (10 µm/zinc-oxide (10 µm and poly(3,4-ethylenedioxythiophenepoly(styrenesulfonate (10 µm. Textile properties such as flexibility, drapability and air permeability are preserved by implementing a pixel-like design of the printed layers. Another route is the application of organic light emitting devices (OLEDs fabricated out of following layers, also starting from the textile substrate: polyurethane or acrylate (10–20 µm as smoothing layer/silver (200 nm/poly(3,4-ethylenedioxythiophenepoly(styrenesulfonate (35 nm/super yellow (80 nm/calcium/aluminum (12/17 nm. Their very thin nm-range layer thickness, preserving the flexibility and drapability of the substrate, and their low working voltage, makes these devices the possible future in light-emitting wearables.

Transparent Conductive Ink for Additive Manufacturing

Science.gov (United States)

Patlan, X. J.; Rolin, T. D.

2017-01-01

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts. Nanotechnology is listed in NASA's Technology Roadmap as a key area to invest for further development.1 This research project focused on using nanotechnology to improve electroluminescent lighting in terms of additive manufacturing and to increase energy efficiency. Specifically, this project's goal was to produce a conductive but transparent printable ink that can be sprayed on any surface for use as one of the electrodes in electroluminescent device design. This innovative work is known as thick film dielectric electroluminescent (TDEL) technology. TDEL devices are used for "backlighting, illumination, and identification due to their tunable color output, scalability, and efficiency" (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). These devices use a 'front-to-back' printing method, where the substrate is the transparent layer, and the dielectric and phosphor are layered on top. This project is a first step in the process of creating a 3D printable 'back-to-front' electroluminescent device. Back-to-front 3D-printed devices are beneficial because they can be printed onto different substrates and embedded in different surfaces, and the substrate is not required to be transparent, all because the light is emitted from the top surface through the transparent conductor. Advances in this area will help further development of printing TDEL devices on an array of different surfaces. Figure 1 demonstrates the layering of the two electrodes that are aligned in a parallel plate capacitor structure (I.K. Small, T.D. Rolin, and A.D. Shields, "3D Printed Electroluminescent Light Panels," NASA Fiscal Year 2017 Center Innovation Fund Proposal, unpublished data, 2017). Voltage is applied across the device, and the subsequent electron excitation results in

Mixing of phosphorescent and exciplex emission in efficient organic electroluminescent devices.

Science.gov (United States)

Cherpak, Vladyslav; Stakhira, Pavlo; Minaev, Boris; Baryshnikov, Gleb; Stromylo, Evgeniy; Helzhynskyy, Igor; Chapran, Marian; Volyniuk, Dmytro; Hotra, Zenon; Dabuliene, Asta; Tomkeviciene, Ausra; Voznyak, Lesya; Grazulevicius, Juozas Vidas

2015-01-21

We fabricated a yellow organic light-emitting diode (OLED) based on the star-shaped donor compound tri(9-hexylcarbazol-3-yl)amine, which provides formation of the interface exciplexes with the iridium(III) bis[4,6-difluorophenyl]-pyridinato-N,C2']picolinate (FIrpic). The exciplex emission is characterized by a broad band and provides a condition to realize the highly effective white OLED. It consists of a combination of the blue phosphorescent emission from the FIrpic complex and a broad efficient delayed fluorescence induced by thermal activation with additional direct phosphorescence from the triplet exciplex formed at the interface. The fabricated exciplex-type device exhibits a high brightness of 38 000 cd/m(2) and a high external quantum efficiency.

Photo and electroluminescence of porous silicon layers

International Nuclear Information System (INIS)

Keshmini, S.H.; Samadpour, S.; Haji-Ali, E.; Rokn-Abadi, M.R.

1995-01-01

Porous silicon (PSi) layers were prepared by both chemical and electrochemical methods on n- and p-type Si substrates. In the former technique, light emission was obtained from p-type and n-type samples. It was found that intense light illumination during the preparation process was essential for PSi formation on n-type substrates. An efficient electrochemical cell with some useful features was designed for electrochemical etching of silicon. Various preparation parameters were studied and photoluminescence emissions ranging from dark red to light blue were obtained from PSi samples prepared on p-type substrates. N-type samples produced emission ranging from dark red to orange yellow. Electroluminescence of porous silicon samples showed that the color of the emission was the same as the photoluminescence color of the sample, and its intensity and duration depended on the current density passed through the sample. The effects of exposure of samples to air, storage in vacuum and heat treatment in air on luminescence intensity of the samples and preparation of patterned porous layers were also studied. (author)

Quantification of Solar Cell Failure Signatures Based on Statistical Analysis of Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Parikh, Harsh; Hacke, Peter

2017-01-01

We demonstrate a method to quantify the extent of solar cell cracks, shunting, or damaged cell interconnects, present in crystalline silicon photovoltaic (PV) modules by statistical analysis of the electroluminescence (EL) intensity distributions of individual cells within the module. From the EL...... intensity distributions (ELID) of each cell, we calculated summary statistics such as standard deviation, median, skewness and kurtosis, and analyzed how they correlate with the magnitude of the solar cell degradation. We found that the dispersion of the ELID increases with the size and severity...

Synthesis and electroluminescent properties of blue fluorescent materials based on 9,9-diethyl-N,N-diphenyl-9 H-fluoren-2-amine substituted anthracene derivatives for organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Seul Bee; Kim, Chanwoo; Park, Soo Na; Kim, Young Seok [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Lee, Ho Won [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@hongik.ac.kr [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2015-11-30

Four 9,9-diethyl-N,N-diphenyl-9 H-fluoren-2-amine substituted anthracene derivatives have been designed and synthesized by Suzuki cross coupling reactions. To explore the electroluminescent properties of these blue materials, multilayer blue organic light-emitting diodes were fabricated in the following device structure: indium tin oxide (180 nm)/N,N’-diphenyl-N,N’-(1-napthyl)-(1,1′-phenyl)-4,4′-diamine (50 nm)/blue emitting materials (1–4) (30 nm)/bathophenanthroline (30 nm)/lithium quinolate (2 nm)/Al (100 nm). All devices appeared excellent deep-blue emissions. Among them, a device exhibited a maximum luminance of 5686 cd/m{sup 2}, the luminous, power and external quantum efficiencies of 5.11 cd/A, 3.79 lm/W, and 4.06% with the Commission International de L'Eclairage coordinates of (0.15, 0.15) at 500 cd/m{sup 2}, respectively. - Highlights: • We synthesized blue fluorescent materials based on anthracene derivatives. • The EL efficiencies of these materials depend on the quantum yields in solid states. • These materials have great potential for applications as blue emitter in OLEDs.

Effect of the polymer emission on the electroluminescence characteristics of n-ZnO nanorods/p-polymer hybrid light emitting diode

Science.gov (United States)

Zaman, S.; Zainelabdin, A.; Amin, G.; Nur, O.; Willander, M.

2011-09-01

Hybrid light emitting diodes (LEDs) based on zinc oxide (ZnO) nanorods and polymers (single and blended) were fabricated and characterized. The ZnO nanorods were grown by the chemical bath deposition method at 50°C. Three different LEDs, with blue emitting, orange-red emitting or their blended polymer together with ZnO nanorods, were fabricated and studied. The current-voltage characteristics show good diode behavior with an ideality factor in the range of 2.1 to 2.27 for all three devices. The electroluminescence spectrum (EL) of the blended device has an emission range from 450 nm to 750 nm, due to the intermixing of the blue emission generated by poly(9,9-dioctylfluorene) denoted as PFO with orange-red emission produced by poly(2-methoxy-5(20-ethyl-hexyloxy)-1,4-phenylenevinylene) 1,4-phenylenevinylene) symbolized as MEH PPV combined with the deep-band emission (DBE) of the ZnO nanorods, i.e. it covers the whole visible region and is manifested as white light. The CIE color coordinates showed bluish, orange-red and white emission from the PFO, MEH PPV and blended LEDs with ZnO nanorods, respectively. These results indicate that the choice of the polymer with proper concentration is critical to the emitted color in ZnO nanorods/p-organic polymer LEDs and careful design should be considered to obtain intrinsic white light sources.

Printing Smart Designs of Light Emitting Devices with Maintained Textile Properties †

Science.gov (United States)

Verboven, Inge; Stryckers, Jeroen; Mecnika, Viktorija; Vandevenne, Glen; Jose, Manoj

2018-01-01

To maintain typical textile properties, smart designs of light emitting devices are printed directly onto textile substrates. A first approach shows improved designs for alternating current powder electroluminescence (ACPEL) devices. A configuration with the following build-up, starting from the textile substrate, was applied using the screen printing technique: silver (10 µm)/barium titanate (10 µm)/zinc-oxide (10 µm) and poly(3,4-ethylenedioxythiophene)poly(styrenesulfonate) (10 µm). Textile properties such as flexibility, drapability and air permeability are preserved by implementing a pixel-like design of the printed layers. Another route is the application of organic light emitting devices (OLEDs) fabricated out of following layers, also starting from the textile substrate: polyurethane or acrylate (10–20 µm) as smoothing layer/silver (200 nm)/poly(3,4-ethylenedioxythiophene)poly(styrenesulfonate) (35 nm)/super yellow (80 nm)/calcium/aluminum (12/17 nm). Their very thin nm-range layer thickness, preserving the flexibility and drapability of the substrate, and their low working voltage, makes these devices the possible future in light-emitting wearables. PMID:29438276

EL device pad-printed on a curved surface

International Nuclear Information System (INIS)

Lee, Taik-Min; Hur, Shin; Kim, Jae-Hyun; Choi, Hyun-Cheol

2010-01-01

This paper is unique in that the electroluminescence (EL) display device is fabricated on a curved surface using the pad-printing method. The precision of the pad-printing process is explored to verify whether it can be used for micro patterning. The minimum pattern size and pattern distortion, which is caused by use of the pad, were tested and simulated. The minimal pattern was found to be 35 µm wide and 2.4 µm thick. Pattern distortion when pad-printing on a flat surface, caused by the deformation of the silicon pad, was less than 5 µm. Numerical analysis shows how to estimate pattern distortion when pad-printing on a curved surface. The proposed EL display device consists of five layers, namely a bottom electrode, dielectric layer, phosphor, transparent electrode and a bus electrode. The ink of each layer was reformulated with solvents and the pad-printing conditions were controlled. A PEN film was used first in order to realize the pad-printing process condition of each layer. Finally, the EL display device was printed onto a dish with a radius of curvature of 80 mm. The luminance was 180 cd m −2

Quantification of solar cell failure signatures based on statistical analysis of electroluminescence images

DEFF Research Database (Denmark)

Spataru, Sergiu; Parikh, Harsh; Benatto, Gisele Alves dos Reis

2017-01-01

We propose a method to identify and quantify the extent of solar cell cracks, shunting, or damaged cell interconnects, present in crystalline silicon photovoltaic (PV) modules by statistical analysis of the electroluminescence (EL) intensity distributions of individual cells within the module. From...... the EL intensity distributions (ELID) of each cell, we calculated summary statistics such as standard deviation, median, skewness and kurtosis, and analyzed how they correlate with the type of the solar cell degradation. We found that the dispersion of the ELID increases with the size and severity...

Molecular-scale simulation of electroluminescence in a multilayer white organic light-emitting diode

DEFF Research Database (Denmark)

Mesta, Murat; Carvelli, Marco; de Vries, Rein J

2013-01-01

we show that it is feasible to carry out Monte Carlo simulations including all of these molecular-scale processes for a hybrid multilayer organic light-emitting diode combining red and green phosphorescent layers with a blue fluorescent layer. The simulated current density and emission profile......In multilayer white organic light-emitting diodes the electronic processes in the various layers--injection and motion of charges as well as generation, diffusion and radiative decay of excitons--should be concerted such that efficient, stable and colour-balanced electroluminescence can occur. Here...

Synthesis of organic EL materials with cyano group and evaluation of emission characteristics in organic EL devices

International Nuclear Information System (INIS)

Kim, Dong Uk

1999-01-01

Nobel electroluminescent materials, polymer material, PU-BCN and low molar mass material, D-BCN with the same chromophores were designed and synthesized. A molecular structure of chromophore was composed of bisstyrylbenzene derivative with cyano groups as electron injection and transport and phenylamine groups as hole injection and transport. Device structures with PU-BCN and D-BCN as an emission layer were fabricated, which were a single-layer device(SL), Indium-tin oxide(ITO)/emission layer/MgAg, and two kinds of double-layer devices which were composed of ITO/emission layer/oxadiazole derivative/MgAg as a DL-E device and ITO/triphenylamine derivative/emission layer/MgAg as a DL-H device. The two emission materials, PU-BCN and D-BCN with the same emission-chromophore were evaluated as having excellent performance of charge injection and transport and revealed almost the same emission characteristics in high current density. EL emission maximum peaks of two material were detected at about 640 nm wavelength of red emission region

Electroluminescence and charge photogeneration in poly(9,9-dihexadecylfluorene-2,7-diyl) and its blends

Czech Academy of Sciences Publication Activity Database

Cimrová, Věra; Výprachtický, Drahomír

2004-01-01

Roč. 212, č. 1 (2004), s. 281-286 ISSN 1022-1360. [Electrical and Related Properties of Polymers and Other Organic Solids /9./. Prague, 14.07.2002-18.07.2002] R&D Projects: GA ČR GA203/01/0512; GA ČR GA102/98/0696 Institutional research plan: CEZ:AV0Z4050913 Keywords : electroluminescence * LEDs * poly(1,4-phenylene)s Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.691, year: 2004

Controlling charge injection in organic electronic devices using self-assembled monolayers

Energy Technology Data Exchange (ETDEWEB)

Campbell, I.H.; Kress, J.D.; Martin, R.L.; Smith, D.L. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Barashkov, N.N.; Ferraris, J.P. [The University of Texas at Dallas, Richardson, Texas 75083 (United States)

1997-12-01

We demonstrate control and improvement of charge injection in organic electronic devices by utilizing self-assembled monolayers (SAMs) to manipulate the Schottky energy barrier between a metal electrode and the organic electronic material. Hole injection from Cu electrodes into the electroluminescent conjugated polymer poly[2-methoxy,5-(2{sup {prime}}-ethyl-hexyloxy)-1,4-phenylene vinylene] was varied by using two conjugated-thiol based SAMs. The chemically modified electrodes were incorporated in organic diode structures and changes in the metal/polymer Schottky energy barriers and current{endash}voltage characteristics were measured. Decreasing (increasing) the Schottky energy barrier improves (degrades) charge injection into the polymer. {copyright} {ital 1997 American Institute of Physics.}

Electroluminescence from a n-ZnO/p-GaN hybrid LED

Energy Technology Data Exchange (ETDEWEB)

Behrends, Arne; Bakin, Andrey; Waag, Andreas [Institute of Semiconductor Technology, Hans-Sommer Str. 66, 38106 Braunschweig (Germany); Kwack, Ho-Sang; Dang, Le Si [Institut Neel, CNRS-UJF, 25, rue des Martyrs, 38042 Grenoble (France)

2010-06-15

In this work we report on the fabrication and characterization of a n-ZnO/p-GaN heterojunction LED. The p-GaN layer was fabricated using MOCVD on Al{sub 2}O{sub 3} with Mg as the acceptor whereas the ZnO nanostructures were grown in a very simple vapor transport system without any additionally doping. Room temperature electroluminescence (EL) measurements show green deep band emission centered at 2.3 eV which is clearly visible with the naked eye when the structure is forward biased. Cathodoluminescence mapping was performed to explain the absence of the band edge emission in the EL spectrum. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Electroluminescence of Multicomponent Conjugated Polymers. 1. Roles of Polymer/Polymer Interfaces in Emission Enhancement and Voltage-Tunable Multicolor Emission in Semiconducting Polymer/Polymer Heterojunctions

National Research Council Canada - National Science Library

Zhang, Xuejun, Ph.D

1999-01-01

Effects of the electronic structure of polymer/polymer interfaces on the electroluminescence efficiency and tunable multicolor emission of polymer heterojunction light-emitting diodes were explored...

Correlating electroluminescence characterization and physics-based models of InGaN/GaN LEDs: Pitfalls and open issues

Energy Technology Data Exchange (ETDEWEB)

Calciati, Marco; Vallone, Marco; Zhou, Xiangyu; Ghione, Giovanni [Dipartimento di Elettronica e Telecomunicazioni, Politecnico di Torino, corso Duca degli Abruzzi 24, 10129 Torino (Italy); Goano, Michele, E-mail: michele.goano@polito.it; Bertazzi, Francesco [Dipartimento di Elettronica e Telecomunicazioni, Politecnico di Torino, corso Duca degli Abruzzi 24, 10129 Torino (Italy); IEIIT-CNR, Politecnico di Torino, corso Duca degli Abruzzi 24, 10129 Torino (Italy); Meneghini, Matteo; Meneghesso, Gaudenzio; Zanoni, Enrico [Dipartimento di Ingegneria dell' Informazione, Università di Padova, Via Gradenigo 6/B, 35131 Padova (Italy); Bellotti, Enrico [Department of Electrical and Computer Engineering, Boston University, 8 Saint Mary' s Street, 02215 Boston, MA (United States); Verzellesi, Giovanni [Dipartimento di Scienze e Metodi dell' Ingegneria, Università di Modena e Reggio Emilia, 42122 Reggio Emilia (Italy); Zhu, Dandan; Humphreys, Colin [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom)

2014-06-15

Electroluminescence (EL) characterization of InGaN/GaN light-emitting diodes (LEDs), coupled with numerical device models of different sophistication, is routinely adopted not only to establish correlations between device efficiency and structural features, but also to make inferences about the loss mechanisms responsible for LED efficiency droop at high driving currents. The limits of this investigative approach are discussed here in a case study based on a comprehensive set of current- and temperature-dependent EL data from blue LEDs with low and high densities of threading dislocations (TDs). First, the effects limiting the applicability of simpler (closed-form and/or one-dimensional) classes of models are addressed, like lateral current crowding, vertical carrier distribution nonuniformity, and interband transition broadening. Then, the major sources of uncertainty affecting state-of-the-art numerical device simulation are reviewed and discussed, including (i) the approximations in the transport description through the multi-quantum-well active region, (ii) the alternative valence band parametrizations proposed to calculate the spontaneous emission rate, (iii) the difficulties in defining the Auger coefficients due to inadequacies in the microscopic quantum well description and the possible presence of extra, non-Auger high-current-density recombination mechanisms and/or Auger-induced leakage. In the case of the present LED structures, the application of three-dimensional numerical-simulation-based analysis to the EL data leads to an explanation of efficiency droop in terms of TD-related and Auger-like nonradiative losses, with a C coefficient in the 10{sup −30} cm{sup 6}/s range at room temperature, close to the larger theoretical calculations reported so far. However, a study of the combined effects of structural and model uncertainties suggests that the C values thus determined could be overestimated by about an order of magnitude. This preliminary

Correlating electroluminescence characterization and physics-based models of InGaN/GaN LEDs: Pitfalls and open issues

Directory of Open Access Journals (Sweden)

Marco Calciati

2014-06-01

Full Text Available Electroluminescence (EL characterization of InGaN/GaN light-emitting diodes (LEDs, coupled with numerical device models of different sophistication, is routinely adopted not only to establish correlations between device efficiency and structural features, but also to make inferences about the loss mechanisms responsible for LED efficiency droop at high driving currents. The limits of this investigative approach are discussed here in a case study based on a comprehensive set of current- and temperature-dependent EL data from blue LEDs with low and high densities of threading dislocations (TDs. First, the effects limiting the applicability of simpler (closed-form and/or one-dimensional classes of models are addressed, like lateral current crowding, vertical carrier distribution nonuniformity, and interband transition broadening. Then, the major sources of uncertainty affecting state-of-the-art numerical device simulation are reviewed and discussed, including (i the approximations in the transport description through the multi-quantum-well active region, (ii the alternative valence band parametrizations proposed to calculate the spontaneous emission rate, (iii the difficulties in defining the Auger coefficients due to inadequacies in the microscopic quantum well description and the possible presence of extra, non-Auger high-current-density recombination mechanisms and/or Auger-induced leakage. In the case of the present LED structures, the application of three-dimensional numerical-simulation-based analysis to the EL data leads to an explanation of efficiency droop in terms of TD-related and Auger-like nonradiative losses, with a C coefficient in the 10−30 cm6/s range at room temperature, close to the larger theoretical calculations reported so far. However, a study of the combined effects of structural and model uncertainties suggests that the C values thus determined could be overestimated by about an order of magnitude. This preliminary

Thermally and electrochemically stable amorphous hole-transporting materials based on carbazole dendrimers for electroluminescent devices

International Nuclear Information System (INIS)

Promarak, Vinich; Ichikawa, Musubu; Sudyoadsuk, Taweesak; Saengsuwan, Sayant; Jungsuttiwong, Siriporn; Keawin, Tinnagon

2008-01-01

Amorphous hole-transporting carbazole dendrimers, 1,4-bis[3,6-di(carbazol-9-yl)carbazol-9-yl]-2,6-di(2-ethylhexyloxy)benzene (G2CB) and 1,4-bis[3,6-di(carbazol-9-yl)carbazol-9-yl]-9-(2-ethylhexyl)carbazole (G2CC), were synthesized by a divergent approach involving bromination and Ullmann coupling reactions. Compounds G2CB and G2CC showed high thermal stability (T g = 206 to 245 deg. C) and excellent electrochemical reversibility. Double-layer organic light-emitting diodes were fabricated by using G2CB and G2CC as hole-transporting layers (HTLs) and tris(8-quinolinato)aluminum (Alq 3 ) as light-emissive layer with the device configuration of indium tin oxide/HTL/Alq 3 /LiF:Al. Both devices exhibited bright green emission from Alq 3 . The device using G2CC as HTL has the best performance with a maximum brightness of 8900 cd/m 2 at 14 V and a low turn-on voltage of 3.5 V

Hybrid device based on GaN nanoneedles and MEH-PPV/PEDOT:PSS polymer

International Nuclear Information System (INIS)

Shin, Min Jeong; Gwon, Dong-Oh; Lee, Chan-Mi; Lee, Gang Seok; Jeon, In-Jun; Ahn, Hyung Soo; Yi, Sam Nyung; Ha, Dong Han

2015-01-01

Highlights: • A hybrid device was demonstrated by using MEH-PPV, PEDOT:PSS, and GaN nanoneedles. • I–V curve of the hybrid device showed its rectification behaviour, similar to a diode. • EL peak originated by the different potential barriers at MEH-PPV and GaN interface. - Abstract: A hybrid device that combines the properties of organic and inorganic semiconductors was fabricated and studied. It incorporated poly[2-methoxy-5-(2-ethylhexyloxy)- 1,4-phenylenevinylene] (MEH-PPV) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as organic polymers and GaN nanoneedles as an inorganic semiconductor. Layers of the two polymers were spin coated on to the GaN nanoneedles. The one peak in the electroluminescence spectrum originated from the MEH-PPV layer owing to the different potential barriers of electrons and holes at its interface with the GaN nanoneedles. However, the photoluminescence spectrum showed peaks due to both GaN nanoneedles and MEH-PPV. Such hybrid structures, suitably developed, might be able to improve the efficiency of optoelectronic devices

Hybrid device based on GaN nanoneedles and MEH-PPV/PEDOT:PSS polymer

Energy Technology Data Exchange (ETDEWEB)

Shin, Min Jeong; Gwon, Dong-Oh; Lee, Chan-Mi; Lee, Gang Seok [Department of Applied Science, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Jeon, In-Jun [Department of Nano-semiconductor Engineering, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Ahn, Hyung Soo [Department of Applied Science, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Department of Nano-semiconductor Engineering, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Yi, Sam Nyung, E-mail: snyi@kmou.ac.kr [Department of Applied Science, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Department of Nano-semiconductor Engineering, Korea Maritime and Ocean University, Busan 606-791 (Korea, Republic of); Ha, Dong Han [Division of Convergence Technology, Korea Research Institute of Standards and Science, Daejeon 305-340 (Korea, Republic of)

2015-08-15

Highlights: • A hybrid device was demonstrated by using MEH-PPV, PEDOT:PSS, and GaN nanoneedles. • I–V curve of the hybrid device showed its rectification behaviour, similar to a diode. • EL peak originated by the different potential barriers at MEH-PPV and GaN interface. - Abstract: A hybrid device that combines the properties of organic and inorganic semiconductors was fabricated and studied. It incorporated poly[2-methoxy-5-(2-ethylhexyloxy)- 1,4-phenylenevinylene] (MEH-PPV) and poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as organic polymers and GaN nanoneedles as an inorganic semiconductor. Layers of the two polymers were spin coated on to the GaN nanoneedles. The one peak in the electroluminescence spectrum originated from the MEH-PPV layer owing to the different potential barriers of electrons and holes at its interface with the GaN nanoneedles. However, the photoluminescence spectrum showed peaks due to both GaN nanoneedles and MEH-PPV. Such hybrid structures, suitably developed, might be able to improve the efficiency of optoelectronic devices.

Use of gas mixture electroluminescence for optical data readout from wire chambers

International Nuclear Information System (INIS)

Polyakov, V.A.; Rykalin, V.I.; Tskhadadze, Eh.G.

1988-01-01

The radiation spectra, the values of electroluminescence yield and coefficients of gas amplification of Ar and Ne mixture with inorganic and organic additions in a wire chamber operating under proportional and self-quenching streamer conditions are measured. Maximum light yield: 2x10 7 photons for Ar+acetone+white spirit gas mixture in a proportional regime and 1.1x10 7 photons for Ar+CO 2 + ethyl alcohol+ white spirit in self-quenching streamer regime is obtained. Three methods of optical data readout from the wire chambers are tested. The best results are obtained when spectrum shifting bands and fibers are placed behind the chamber cathode planes

Electroluminescence Analysis by Tilt Polish Technique of InP-Based Semiconductor Lasers

Science.gov (United States)

Ichikawa, Hiroyuki; Sasaki, Kouichi; Hamada, Kotaro; Yamaguchi, Akira

2010-03-01

We developed an effective electroluminescence (EL) analysis method to specify the degraded region of InP-based semiconductor lasers. The EL analysis method is one of the most important methods for failure analysis. However, EL observation was difficult because opaque electrodes surround an active layer. A portion of each electrode had to be left intact for wiring to inject the current. Thus, we developed a partial polish technique for the bottom electrode. Tilt polish equipment with a rotating table was introduced; a flat polished surface and a sufficiently wide remaining portion of the bottom electrode were obtained. As a result, clear EL from the back surface of the laser was observed.

Recent developments of truly stretchable thin film electronic and optoelectronic devices.

Science.gov (United States)

Zhao, Juan; Chi, Zhihe; Yang, Zhan; Chen, Xiaojie; Arnold, Michael S; Zhang, Yi; Xu, Jiarui; Chi, Zhenguo; Aldred, Matthew P

2018-03-29

Truly stretchable electronics, wherein all components themselves permit elastic deformation as the whole devices are stretched, exhibit unique advantages over other strategies, such as simple fabrication process, high integrity of entire components and intimate integration with curvilinear surfaces. In contrast to the stretchable devices using stretchable interconnectors to integrate with rigid active devices, truly stretchable devices are realized with or without intentionally employing structural engineering (e.g. buckling), and the whole device can be bent, twisted, or stretched to meet the demands for practical applications, which are beyond the capability of conventional flexible devices that can only bend or twist. Recently, great achievements have been made toward truly stretchable electronics. Here, the contribution of this review is an effort to provide a panoramic view of the latest progress concerning truly stretchable electronic devices, of which we give special emphasis to three kinds of thin film electronic and optoelectronic devices: (1) thin film transistors, (2) electroluminescent devices (including organic light-emitting diodes, light-emitting electrochemical cells and perovskite light-emitting diodes), and (3) photovoltaics (including organic photovoltaics and perovskite solar cells). We systematically discuss the device design and fabrication strategies, the origin of device stretchability and the relationship between the electrical and mechanical behaviors of the devices. We hope that this review provides a clear outlook of these attractive stretchable devices for a broad range of scientists and attracts more researchers to devote their time to this interesting research field in both industry and academia, thus encouraging more intelligent lifestyles for human beings in the coming future.

Preparation and characterizations of electroluminescent p-ZnO : N/n-ZnO : Ga/ITO thin films by spray pyrolysis method

Directory of Open Access Journals (Sweden)

C. Panatarani

2016-02-01

Full Text Available ZnO thin films were fabricated by spray pyrolysis (SP method with p-ZnO : N/n-ZnO:Ga/ITO structure. The X-ray results show that the deposited films have hexagonal wurtzite structure. The EDS results observed that the composition of Ga in ZnO:Ga and N in ZnO:N was 3.73% and 27.73% respectively. The photoluminescence (PL with excitation wave length of 260 nm shows that ZnO:Ga and ZnO:N films emitted UV emission at ∼393 and ∼388 nm, respectively and the films resistivity was 7.12 and 12.80 Ohm-cm respectively. The electroluminescence of the p-ZnO : N/n-ZnO:Ga/ITO structure was obtained by applying forward bias of 5 volt with 30 mA current, resulting in a 3.35 volt threshold bias with the peak electroluminescence in UV-blue range.

ZnO-nanorod-array/p-GaN high-performance ultra-violet light emitting devices prepared by simple solution synthesis

Science.gov (United States)

Jha, Shrawan Kumar; Luan, Chunyan; To, Chap Hang; Kutsay, Oleksandr; Kováč, Jaroslav; Zapien, Juan Antonio; Bello, Igor; Lee, Shuit-Tong

2012-11-01

Pure ultra-violet (UV) (378 nm) electroluminescence (EL) from zinc oxide (ZnO)-nanorod-array/p-gallium nitride (GaN) light emitting devices (LEDs) is demonstrated at low bias-voltages (˜4.3 V). Devices were prepared merely by solution-synthesis, without any involvement of sophisticated material growth techniques or preparation methods. Three different luminescence characterization techniques, i.e., photo-luminescence, cathodo-luminescence, and EL, provided insight into the nature of the UV emission mechanism in solution-synthesized LEDs. Bias dependent EL behaviour revealed blue-shift of EL peaks and increased peak sharpness, with increasing the operating voltage. Accelerated bias stress tests showed very stable and repeatable electrical and EL performance of the solution-synthesized nanorod LEDs.

Improved efficiency in organic light-emitting devices with tris-(8-hydroxyquinoline) aluminium doped 9,10-di(2-naphthyl) anthracene emission layer

Energy Technology Data Exchange (ETDEWEB)

Yuan Yongbo; Lian Jiarong; Li Shuang; Zhou Xiang [State Key Lab of Optoelectronic Materials and Technologies, Sun Yat-Sen University, Guangzhou, 510275 (China)], E-mail: stszx@mail.sysu.edu.cn

2008-11-21

Organic light-emitting devices with tris-(8-hydroxyquinoline) aluminium (Alq{sub 3}) doped 9,10-di(2-naphthyl) anthracene (ADN) as the emission layer (EML) have been fabricated. These devices exhibit efficient electroluminescence (EL) originated from the Alq{sub 3} as the mass ratio of Alq{sub 3} to ADN was varied from 1 to 50%. The devices with an optimal Alq{sub 3} mass ratio of 10 wt% showed a peak EL efficiency and an external quantum efficiency of 9.1 cd A{sup -1} and 2.7% at a luminance of 1371 cd m{sup -2}, which is improved by a factor of 2.2 compared with 4.1 cd A{sup -1} and 1.2% at a luminance of 3267 cd m{sup -2} for conventional devices with the neat Alq{sub 3} as the EML.

Kinetics of transient electroluminescence in organic light emitting diodes

Science.gov (United States)

Shukla, Manju; Kumar, Pankaj; Chand, Suresh; Brahme, Nameeta; Kher, R. S.; Khokhar, M. S. K.

2008-08-01

Mathematical simulation on the rise and decay kinetics of transient electroluminescence (EL) in organic light emitting diodes (OLEDs) is presented. The transient EL is studied with respect to a step voltage pulse. While rising, for lower values of time, the EL intensity shows a quadratic dependence on (t - tdel), where tdel is the time delay observed in the onset of EL, and finally attains saturation at a sufficiently large time. When the applied voltage is switched off, the initial EL decay shows an exponential dependence on (t - tdec), where tdec is the time when the voltage is switched off. The simulated results are compared with the transient EL performance of a bilayer OLED based on small molecular bis(2-methyl 8-hydroxyquinoline)(triphenyl siloxy) aluminium (SAlq). Transient EL studies have been carried out at different voltage pulse amplitudes. The simulated results show good agreement with experimental data. Using these simulated results the lifetime of the excitons in SAlq has also been calculated.

Kinetics of transient electroluminescence in organic light emitting diodes

International Nuclear Information System (INIS)

Shukla, Manju; Brahme, Nameeta; Kumar, Pankaj; Chand, Suresh; Kher, R S; Khokhar, M S K

2008-01-01

Mathematical simulation on the rise and decay kinetics of transient electroluminescence (EL) in organic light emitting diodes (OLEDs) is presented. The transient EL is studied with respect to a step voltage pulse. While rising, for lower values of time, the EL intensity shows a quadratic dependence on (t - t del ), where t del is the time delay observed in the onset of EL, and finally attains saturation at a sufficiently large time. When the applied voltage is switched off, the initial EL decay shows an exponential dependence on (t - t dec ), where t dec is the time when the voltage is switched off. The simulated results are compared with the transient EL performance of a bilayer OLED based on small molecular bis(2-methyl 8-hydroxyquinoline)(triphenyl siloxy) aluminium (SAlq). Transient EL studies have been carried out at different voltage pulse amplitudes. The simulated results show good agreement with experimental data. Using these simulated results the lifetime of the excitons in SAlq has also been calculated

A discotic triphenylene dimer as organic hole transporting material for electroluminescence devices

International Nuclear Information System (INIS)

Mao Huaxiang; He Zhiqun; Wang Junling; Zhang Chunxiu; Xie, Ping; Zhang Rongben

2007-01-01

A triphenylene dimer, an intermediate between a discotic triphenylene molecule and the macromolecule, had been prepared by linking together two triphenylene units via phenylene carbamate linkages, which was formed through a reaction between one 1,4-phenylene diisocyanate and two hydroxyl end groups on flexible substituents of triphenylenes. The dimer exhibited good film-forming property. Its temperature-dependent phase transitions were investigated using differential scanning calorimetry and polarized optical microscopy. Room temperature microstructure of the dimer was analyzed by X-ray diffraction. Charge mobility of the triphenylene dimer was also measured. Our preliminary result using the materials in a sandwich light-emitting device is reported here. It demonstrates that the triphenylene dimer is a promising candidate as a hole transporting material

White-light emission from porous-silicon-aluminium Schottky junctions

International Nuclear Information System (INIS)

Masini, G.; La Monica, S.; Maiello, G.

1996-01-01

Porous-silicon-based white-light-emitting devices are presented. The fabrication process on different substrates is described. The peculiarities of technological steps for device fabrication (porous-silicon formation and aluminium treatment) are underlined. Doping profile of the porous layer, current-voltage characteristics, time response, lifetime tests and electroluminescence emission spectrum of the device are presented. A model for electrical behaviour of Al/porous silicon Schottky junction is presented. Electroluminescence spectrum of the presented devices showed strong similarities with white emission from crystalline silicon junctions in the breakdown region

Dual functions of a new n-type conjugated dendrimer: light-emitting material and additive for polymer electroluminescent devices

International Nuclear Information System (INIS)

Park, Jong Hyeok; Kim, Chulhee; Kim, Young Chul

2009-01-01

We demonstrate a novel light-emitting diode (LED) of a graded bilayer structure that comprises poly(N-vinylcarbazole) (PVK) with good hole transport ability as the energy donor and a new distyrylanthracene-triazine-based dendrimer with enhanced electron transport ability as the light-emitting molecule. The device contains a graded bilayer structure of the PVK film covered with the dendrimer film prepared by sequential spin-casting of the dendrimer layer from a solvent that only swells the PVK layer. The bilayer device demonstrated a significantly enhanced electoluminescence quantum efficiency compared with the dendrimer single layer device or the PVK : dendrimer blend device with optimized composition. We also prepared composite LEDs with an MEH-PPV : emissive dendrimer blend. By doping the electron-deficient MEH-PPV layer with a small amount of the distyrylanthracene-triazine-based dendrimer, we could not only enhance the device performance but also depress the long-wavelength emission of MEH-PPV.

Dual functions of a new n-type conjugated dendrimer: light-emitting material and additive for polymer electroluminescent devices

Energy Technology Data Exchange (ETDEWEB)

Park, Jong Hyeok [Department of Chemical Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Chulhee [Hyperstructured Organic Materials Research Center, Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of); Kim, Young Chul, E-mail: kimyc@khu.ac.k [Department of Chemical Engineering and RIC-CAMID, Kyung Hee University, Yongin-si, Kyunggi-do 499-701 (Korea, Republic of)

2009-02-07

We demonstrate a novel light-emitting diode (LED) of a graded bilayer structure that comprises poly(N-vinylcarbazole) (PVK) with good hole transport ability as the energy donor and a new distyrylanthracene-triazine-based dendrimer with enhanced electron transport ability as the light-emitting molecule. The device contains a graded bilayer structure of the PVK film covered with the dendrimer film prepared by sequential spin-casting of the dendrimer layer from a solvent that only swells the PVK layer. The bilayer device demonstrated a significantly enhanced electoluminescence quantum efficiency compared with the dendrimer single layer device or the PVK : dendrimer blend device with optimized composition. We also prepared composite LEDs with an MEH-PPV : emissive dendrimer blend. By doping the electron-deficient MEH-PPV layer with a small amount of the distyrylanthracene-triazine-based dendrimer, we could not only enhance the device performance but also depress the long-wavelength emission of MEH-PPV.

Dual functions of a new n-type conjugated dendrimer: light-emitting material and additive for polymer electroluminescent devices

Science.gov (United States)

Hyeok Park, Jong; Kim, Chulhee; Kim, Young Chul

2009-02-01

We demonstrate a novel light-emitting diode (LED) of a graded bilayer structure that comprises poly(N-vinylcarbazole) (PVK) with good hole transport ability as the energy donor and a new distyrylanthracene-triazine-based dendrimer with enhanced electron transport ability as the light-emitting molecule. The device contains a graded bilayer structure of the PVK film covered with the dendrimer film prepared by sequential spin-casting of the dendrimer layer from a solvent that only swells the PVK layer. The bilayer device demonstrated a significantly enhanced electoluminescence quantum efficiency compared with the dendrimer single layer device or the PVK : dendrimer blend device with optimized composition. We also prepared composite LEDs with an MEH-PPV : emissive dendrimer blend. By doping the electron-deficient MEH-PPV layer with a small amount of the distyrylanthracene-triazine-based dendrimer, we could not only enhance the device performance but also depress the long-wavelength emission of MEH-PPV.

Localized Surface Plasmon-Enhanced Electroluminescence in OLEDs by Self-Assembly Ag Nanoparticle Film

Science.gov (United States)

He, Xiaoxiao; Wang, Wenjun; Li, Shuhong; Wang, Qingru; Zheng, Wanquan; Shi, Qiang; Liu, Yunlong

2015-12-01

We fabricated Ag nanoparticle (NP) film in organic light emission diodes (OLEDs), and a 23 times increase in electroluminescence (EL) at 518 nm was probed by time-resolved EL measurement. The luminance and relative external quantum efficiency (REQE) were increased by 5.4 and 3.7 times, respectively. There comes a new energy transport way that localized surface plasmons (LSPs) would absorb energy that corresponds to the electron-hole pair before recombination, promoting the formation of electron-hole pair and exciting local surface plasmon resonance (LSPR). The extended lifetime of Alq3 indicates the existence of strong interaction between LSPR and exciton, which decreases the nonradiative decay rate of OLEDs.

Visible-light electroluminescence in Mn-doped GaAs light-emitting diodes

International Nuclear Information System (INIS)

Nam Hai, Pham; Maruo, Daiki; Tanaka, Masaaki

2014-01-01

We observed visible-light electroluminescence (EL) due to d-d transitions in light-emitting diodes with Mn-doped GaAs layers (here, referred to as GaAs:Mn). Besides the band-gap emission of GaAs, the EL spectra show two peaks at 1.89 eV and 2.16 eV, which are exactly the same as 4 A 2 ( 4 F) → 4 T 1 ( 4 G) and 4 T 1 ( 4 G) → 6 A 1 ( 6 S) transitions of Mn atoms doped in ZnS. The temperature dependence and the current-density dependence are consistent with the characteristics of d-d transitions. We explain the observed EL spectra by the p-d hybridized orbitals of the Mn d electrons in GaAs

Exciplex formation and electroluminescent absorption in ultraviolet organic light-emitting diodes

International Nuclear Information System (INIS)

Zhang Qi; Zhang Hao; Xu Tao; Wei Bin; Zhang Xiao-Wen

2015-01-01

We investigated the formation of exciplex and electroluminescent absorption in ultraviolet organic light-emitting diodes (UV OLEDs) using different heterojunction structures. It is found that an energy barrier of over 0.3 eV between the emissive layer (EML) and adjacent transport layer facilitates exciplex formation. The electron blocking layer effectively confines electrons in the EML, which contributes to pure UV emission and enhances efficiency. The change in EML thickness generates tunable UV emission from 376 nm to 406 nm. In addition, the UV emission excites low-energy organic function layers and produces photoluminescent emission. In UV OLED, avoiding the exciplex formation and averting light absorption can effectively improve the purity and efficiency. A maximum external quantum efficiency of 1.2% with a UV emission peak of 376 nm is realized. (paper)

Emission properties of porphyrin compounds in new polymeric PS:CBP host

Science.gov (United States)

Jafari, Mohammad Reza; Bahrami, Bahram

2015-06-01

In this study, a device with fundamental structure of ITO/PEDOT:PSS (60 nm)/PS:CBP (70 nm)/Al (150 nm) was fabricated. The electroluminescence spectrum of device designated a red shift rather than PS:CBP photoluminescence spectra. It can be suggested that the electroplex emission occurs at PS:CBP interface. By following this step, red light-emitting devices using porphyrin compounds as a red dopant in a new host material PS:CBP with a configuration of ITO/PEDOT:PSS (60 nm)/PS:CBP:porphyrin compounds(70 nm)/Al (150 nm) have been fabricated and investigated. The electroluminescent spectra of the porphyrin compounds were red-shifted as compared with the PS:CBP blend. OLED devices based on doping 3,4PtTPP and TPPNO2 in PS:CBP showed purer red emission compared with ZnTPP and CoTPP doped devices. We believe that the electroluminescence performance of OLED devices based on porphyrin compounds depends on overlaps between the absorption of the porphyrin compounds and the emission of PS:CBP.

Preparation and performance optimization of TPBISi green-light organic luminescent material devices

Directory of Open Access Journals (Sweden)

Zheng Huajing

2017-01-01

Full Text Available The Study analyzed and tested the absorption spectrum, photoluminescence spectrum, and device’s electroluminescence spectrum of a new silole material. The device with Silol as an emitting layer, emitted green-light whose structure is ITO/NPB/2,2,3,3-tetraphenyl-4,4-bisthienylsilole(TPBTSi/Alq3/Mg: A by improvement of preparation technology and optimization of thin film. It reaches the maximum luminescence of 11290.2 cd/m2, the maximum luminous efficiency of 0.84 lm/W, luminescence spectrum of 516 nm, chromaticity diagram CIE coordinate of(0.275, 0.4568 when voltage is 15V. All of the above is the green characteristic spectrum of TPBTSi.

The nature of trapping sites and recombination centres in PVK and PVK-PBD electroluminescent matrices seen by spectrally resolved thermoluminescence

International Nuclear Information System (INIS)

Glowacki, Ireneusz; Szamel, Zbigniew

2010-01-01

Two electroluminescent polymer matrices poly(N-vinylcarbazole) (PVK) and PVK with 40 wt% of 2-tert-butylphenyl-5-biphenyl-1,3,4-oxadiazole (PBD) were studied using spectrally resolved thermoluminescence (SRTL) in the temperature range 15-325 K. The comparison of the SRTL results with the electroluminescence (EL) spectra has allowed identification of the localized (trapping) sites and the radiative recombination centres present in the investigated matrices. In the neat PVK films deep traps with a depth about 200 meV, related to triplet excimers dominate, while in the PVK-PBD (40 wt%) blend films the traps that are related to triplet exciplexes formed by the carbazole groups and the PBD molecules dominate. Depth of the traps in the PVK-PBD blend is somewhat lower than that in the neat PVK. An analysis of the EL spectra shows that in the PVK and in the PVK-PBD blend the dominant radiative centres are singlet excimers and singlet exciplexes, respectively. However, in the neat PVK some contributions of the triplet monomer and the triplet excimer states in the EL were also detected.

The effect of C60 doping on the electroluminescent performance of organic light-emitting devices

International Nuclear Information System (INIS)

Xu Denghui; Deng Zhenbo; Xiao Jing; Guo Dong; Hao Jingang; Zhang Yuanyuan; Gao Yinhao; Liang Chunjun

2007-01-01

Organic light-emitting devices (OLEDs) with the PVK hole transport layer were fabricated. The effect of C 60 doping in the hole transport PVK layer on the performance of the devices was investigated by changing the C 60 content from 0 to 3.0 wt%. The OLEDs had a structure of ITO/PEDOT:PSS/PVK:C 60 (0, 0.5, 1.0, 2.0, 3.0 wt%)/AlQ/LiF/Al. The doping led to a higher conductivity in C 60 -doped PVK layer and the hole mobility of PVK was improved from 4.5x10 -7 to 2.6x10 -6 cm 2 /Vs with the doping concentration of C 60 changing from 0 to 3.0 wt%. Moreover, the doping led to a high density of equilibrium charges carriers, which facilitated hole injection and transport. Doping of C 60 in PVK resulted in efficient hole injection and low drive voltage at high luminance

The Electric and Optical Properties of Doped Small Molecular Organic Light-Emitting Devices

International Nuclear Information System (INIS)

Kwang-Ohk Cheon

2003-01-01

Organic light-emitting devices (OLEDs) constitute a new and exciting emissive display technology. In general, the basic OLED structure consists of a stack of fluorescent organic layers sandwiched between a transparent conducting-anode and metallic cathode. When an appropriate bias is applied to the device, holes are injected from the anode and electrons from the cathode; some of the recombination events between the holes and electrons result in electroluminescence (EL). Until now, most of the efforts in developing OLEDs have focused on display applications, hence on devices within the visible range. However some organic devices have been developed for ultraviolet or infrared emission. Various aspects of the device physics of doped small molecular OLEDs were described and discussed. The doping layer thickness and concentration were varied systematically to study their effects on device performances, energy transfer, and turn-off dynamics. Low-energy-gap DCM2 guest molecules, in either α-NPD or DPVBi host layers, are optically efficient fluorophores but also generate deep carrier trap-sites. Since their traps reduce the carrier mobility, the current density decreases with increased doping concentration. At the same time, due to efficient energy transfer, the quantum efficiency of the devices is improved by light doping or thin doping thickness, in comparison with the undoped neat devices. However, heavy doping induces concentration quenching effects. Thus, the doping concentration and doping thickness may be optimized for best performance

The Electric and Optical Properties of Doped Small Molecular Organic Light-Emitting Devices

Energy Technology Data Exchange (ETDEWEB)

Cheon, Kwang-Ohk [Iowa State Univ., Ames, IA (United States)

2003-01-01

Organic light-emitting devices (OLEDs) constitute a new and exciting emissive display technology. In general, the basic OLED structure consists of a stack of fluorescent organic layers sandwiched between a transparent conducting-anode and metallic cathode. When an appropriate bias is applied to the device, holes are injected from the anode and electrons from the cathode; some of the recombination events between the holes and electrons result in electroluminescence (EL). Until now, most of the efforts in developing OLEDs have focused on display applications, hence on devices within the visible range. However some organic devices have been developed for ultraviolet or infrared emission. Various aspects of the device physics of doped small molecular OLEDs were described and discussed. The doping layer thickness and concentration were varied systematically to study their effects on device performances, energy transfer, and turn-off dynamics. Low-energy-gap DCM2 guest molecules, in either α-NPD or DPVBi host layers, are optically efficient fluorophores but also generate deep carrier trap-sites. Since their traps reduce the carrier mobility, the current density decreases with increased doping concentration. At the same time, due to efficient energy transfer, the quantum efficiency of the devices is improved by light doping or thin doping thickness, in comparison with the undoped neat devices. However, heavy doping induces concentration quenching effects. Thus, the doping concentration and doping thickness may be optimized for best performance.

Highly efficient phosphorescent blue and white organic light-emitting devices with simplified architectures

Energy Technology Data Exchange (ETDEWEB)

Chang, Chih-Hao, E-mail: chc@saturn.yzu.edu.tw [Department of Photonics Engineering, Yuan Ze University, Chung-Li, Taiwan 32003 (China); Ding, Yong-Shung; Hsieh, Po-Wei; Chang, Chien-Ping; Lin, Wei-Chieh [Department of Photonics Engineering, Yuan Ze University, Chung-Li, Taiwan 32003 (China); Chang, Hsin-Hua, E-mail: hhua3@mail.vnu.edu.tw [Department of Electro-Optical Engineering, Vanung University, Chung-Li, Taiwan 32061 (China)

2011-09-01

Blue phosphorescent organic light-emitting devices (PhOLEDs) with quantum efficiency close to the theoretical maximum were achieved by utilizing a double-layer architecture. Two wide-triplet-gap materials, 1,3-bis(9-carbazolyl)benzene and 1,3,5-tri[(3-pyridyl)-phen-3-yl]benzene, were employed in the emitting and electron-transport layers respectively. The opposite carrier-transport characteristics of these two materials were leveraged to define the exciton formation zone and thus increase the probability of recombination. The efficiency at practical luminance (100 cd/m{sup 2}) was as high as 20.8%, 47.7 cd/A and 31.2 lm/W, respectively. Furthermore, based on the design concept of this simplified architecture, efficient warmish-white PhOLEDs were developed. Such two-component white organic light-emitting devices exhibited rather stable colors over a wide brightness range and yielded electroluminescence efficiencies of 15.3%, 33.3 cd/A, and 22.7 lm/W in the forward directions.

Highly efficient phosphorescent blue and white organic light-emitting devices with simplified architectures

International Nuclear Information System (INIS)

Chang, Chih-Hao; Ding, Yong-Shung; Hsieh, Po-Wei; Chang, Chien-Ping; Lin, Wei-Chieh; Chang, Hsin-Hua

2011-01-01

Blue phosphorescent organic light-emitting devices (PhOLEDs) with quantum efficiency close to the theoretical maximum were achieved by utilizing a double-layer architecture. Two wide-triplet-gap materials, 1,3-bis(9-carbazolyl)benzene and 1,3,5-tri[(3-pyridyl)-phen-3-yl]benzene, were employed in the emitting and electron-transport layers respectively. The opposite carrier-transport characteristics of these two materials were leveraged to define the exciton formation zone and thus increase the probability of recombination. The efficiency at practical luminance (100 cd/m 2 ) was as high as 20.8%, 47.7 cd/A and 31.2 lm/W, respectively. Furthermore, based on the design concept of this simplified architecture, efficient warmish-white PhOLEDs were developed. Such two-component white organic light-emitting devices exhibited rather stable colors over a wide brightness range and yielded electroluminescence efficiencies of 15.3%, 33.3 cd/A, and 22.7 lm/W in the forward directions.

Photo- and electro-luminescence of rare earth doped ZnO electroluminors at liquid nitrogen temperature

International Nuclear Information System (INIS)

Bhushan, S.; Kaza, B.R.; Pandey, A.N.

1981-01-01

Photo (PL) and electroluminescent (EL) spectra of some rare earth (La, Gd, Er or Dy) doped ZnO electroluminors have been investigated at liquid nitrogen temperature (LNT) and compared with their corresponding results at room temperature (RT). In addition to three bands observed at RT, one more band on the higher wavelength side appears in EL spectra. Spectral shift with the exciting intensity at LNT supports the donor-acceptor (DA) model in which the rare earths form the donor levels. From the temperature dependent studies of PL and EL brightness, the EL phenomenon is found to be more susceptible to traps. (author)

Study on the visibility of an electroluminescent display for automobiles; Jidoshayo EL display no shininsei

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, N; Harada, M; Idogaki, T [Denso Corp., Aichi (Japan)

1997-10-01

This report explores the visibility of an Electroluminescent (EL) display for automotive use. Displays for automobiles are exposed to the direct rays of the sun and forced to operate in wide temperature range. Therefore, luminous flux density by the lighting on EL display panel and operating environment temperature must be considered for the visibility evaluation. Sensory evaluation on the visibility and physical measurements such as contrast, chromaticity difference in accordance with the viewing angle change indicate that the visibility of the EL display for automobiles is advantageous over other displays. 6 refs., 11 figs., 1 tab.

Characterization of Semiconductor Nanocrystal Assemblies as Components of Optoelectronic Devices

Science.gov (United States)

Malfavon-Ochoa, Mario

This dissertation presents new insight into the ability of small molecule passivated NCs to achieve intimate approach distances, despite being well passivated, while developing guiding principles in the area of ligand mediated microstructure control and the resulting macroscopic optical and electronic properties that close packing of high quality NCs enables. NC ligand coverage will be characterized quantitatively through thermogravimetric analysis (TGA), and qualitatively by photoluminescence and electroluminescence, in the case of functional devices; illustrating the importance of practitioner dependent control of ligand coverage through variations in the dispersion precipitation purification procedure. A unique examination of the relative contribution of energy and charge transfer in NC LEDs will demonstrate the ability to achieve charge transfer, at a level competitive with energy transfer, to well passivated NCs at various wt% loading in a polymer matrix. The observation of potential dependent recombination zones within an active layer further suggest novel, NC surface passivation mediated control of blend microstructure during solution processing towards the development of a bi-continuous network. Next, NC self-assembly and resulting microstructure dependent optical and electronic properties will be examined through electroluminescence and high-resolution transmission electron microscopy (TEM) micrographs of functional NC/polymer bulk heterojunction LEDs. The joint characterization of NC optical properties, and self-assembly microstructure provide a deeper understanding of the significant and inseparable effects of minimal changes in NC surface passivation on structure and function, and emphasize the potential to rely on strongly passivating ligands to control physical properties and processing parameters concurrently towards higher efficiency devices via low cost processing. Finally, micro-contact printing of blazed transmission gratings, using stable

On the origin of excimer emission in electroluminescence and photoluminescence spectra of polyfluorenes

International Nuclear Information System (INIS)

Vacha, Martin; Ha, Jaekook; Sato, Hisaya

2007-01-01

We report a study on the differences in red-shifted excimer band in photoluminescence (PL) and electroluminescence (EL) spectra of thin films of a copolymer of dibutylfluorene and butylphenylphenoxazine. The relative intensity of the excimer band in PL spectra increases with temperature above the polymer glass transition, and with the intensity of the excitation light. In EL spectra, on the other hand, the relative excimer intensity is seen to decrease with increasing driving voltage. These opposite trends originate from the different nature of excitations in PL and EL spectra: photoexcitation directly creates singlet excitons while electric excitation proceeds via interaction of injected electrons and holes. In case of electric excitation, the observed results might be due to trap-assisted excimer formation

Influence of gamma-irradiation on the electroluminescence of ZnSe:Zn,Te crystals

International Nuclear Information System (INIS)

Elmuratova, D.B.; Ibragimova, E.M.

2007-01-01

Effect of 60 Co gamma-radiation at the dose rate of 10 Gy/s on electroluminescence (El)Zn Se crystals with 0.5 weight % Te treated in zinc vapor was studied for possible manufacturing of light emitting structures. Broad El band with the maximum at 610 nm is excited in the origin samples at a voltage above 15 V. After irradiation to the high dose of 10 6 Gy the El intensity grows by ∼2.5 times in the direct polarity at 24 V. The observed El of Zn Se:Zn,Te single crystals is assumed to be caused by the charge carrier recombination at the interstitial zinc centers by the excitation mechanism of a barrier sub breakdown type (authors)

Analysis of interfacial energy states in Au/pentacene/polyimide/indium-zinc-oxide diodes by electroluminescence spectroscopy and electric-field-induced optical second-harmonic generation measurement

Science.gov (United States)

Taguchi, Dai; Manaka, Takaaki; Iwamoto, Mitsumasa

2016-03-01

By using electroluminescence (EL) spectroscopy and electric-field-induced optical second-harmonic generation (EFISHG) measurement, we analyzed interfacial energy states in Au/pentacene/polyimide/indium-zinc-oxide (IZO) diodes, to characterize the pentacene/polyimide interface. Under positive voltage application to the Au electrode with reference to the IZO electrode, the EFISHG showed that holes are injected from Au electrode, and accumulate at the pentacene/polyimide interface with the surface charge density of Qs = 3.8 × 10-7 C/cm2. The EL spectra suggested that the accumulated holes are not merely located in the pentacene but they are transferred to the interface states of polyimide. These accumulated holes distribute with the interface state density greater than 1012 cm-2 eV-1 in the range E = 1.5-1.8 and 1.7-2.4 eV in pentacene and in polyimide, respectively, under assumption that accumulated holes govern recombination radiation. The EL-EFISHG measurement is helpful to characterize organic-organic layer interfaces in organic devices and provides a way to analyze interface energy states.

Poly[(arylene ethynylene)-alt-(arylene vinylene)]s based on anthanthrone and its derivatives: synthesis and photophysical, electrochemical, electroluminescent, and photovoltaic properties

Czech Academy of Sciences Publication Activity Database

John, S. V.; Cimrová, Věra; Ulbricht, C.; Pokorná, Veronika; Růžička, Aleš; Giguére, J.-B.; Lafleur-Lambert, A.; Morin, J.-F.; Iwuoha, E.; Egbe, D. A. M.

2017-01-01

Roč. 50, č. 21 (2017), s. 8357-8371 ISSN 0024-9297 R&D Projects: GA ČR(CZ) GA13-26542S Institutional support: RVO:61389013 Keywords : polycyclic aromatic compounds * anthanthrones and anthanthrone derivatives * electroluminescence Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 5.835, year: 2016

Enhanced performance of organic light-emitting devices by using electropolymerized poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) film as the anode modification layer

Energy Technology Data Exchange (ETDEWEB)

Liu Xiaona [Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Yan Jun [Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Meng Lingchuan [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Sun Chenghua; Hu Xiujie; Chen Ping [Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Zhou Shuyun, E-mail: zhou_shuyun@mail.ipc.ac.cn [Key Laboratory of Photochemical Conversion and Optoelectronic Materials, Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190 (China); Teng Feng [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China)

2012-01-31

Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films were prepared by electropolymerization on patterned indium tin oxide substrates in isopropanol solution. The thickness and doping level of the PEDOT:PSS films were controlled by adjusting the electropolymerization time and the concentration of poly(styrene sulfonate) acid, respectively. Organic light-emitting diodes were fabricated using the electropolymerized PEDOT:PSS film as the anode modification layer. The dependence of the performance on thickness of PEDOT:PSS films was investigated. It is shown that the performance of the device can be further enhanced when the thickness of PEDOT:PSS films reached an optimum condition. This method facilitates manufacturing procedures of conducting polymers films and may offer an economical route for producing organic electroluminescent devices.

Exciplex formation and electroluminescent absorption in ultraviolet organic light-emitting diodes

Science.gov (United States)

Zhang, Qi; Zhang, Hao; Zhang, Xiao-Wen; Xu, Tao; Wei, Bin

2015-02-01

We investigated the formation of exciplex and electroluminescent absorption in ultraviolet organic light-emitting diodes (UV OLEDs) using different heterojunction structures. It is found that an energy barrier of over 0.3 eV between the emissive layer (EML) and adjacent transport layer facilitates exciplex formation. The electron blocking layer effectively confines electrons in the EML, which contributes to pure UV emission and enhances efficiency. The change in EML thickness generates tunable UV emission from 376 nm to 406 nm. In addition, the UV emission excites low-energy organic function layers and produces photoluminescent emission. In UV OLED, avoiding the exciplex formation and averting light absorption can effectively improve the purity and efficiency. A maximum external quantum efficiency of 1.2% with a UV emission peak of 376 nm is realized. Project supported by the National Natural Science Foundation of China (Grant Nos. 61136003 and 61275041) and the Guangxi Provincial Natural Science Foundation, China (Grant No. 2012GXNSFBA053168).

New Copolymers Containing Charge Carriers for Organic Devices with ITO Films Treated by UV-Ozone Using High Intensity Discharge Lamp

Directory of Open Access Journals (Sweden)

Emerson Roberto SANTOS

2009-02-01

Full Text Available For electroluminescent devices new copolymers were synthesized using a Suzuki cross-coupling reaction based on monomers (fluorine-alt-phenylene in conjugation with quinoline-alt-phenylene units. They were characterized by 1H NMR, 13C NMR and FTIR. TGA measurements indicated that the copolymers have good thermal properties and no weight loss was observed up to 250 °C. The UV-Vis spectra were characterized by absorptions from the fluorene-alt-phenylene and quinoline-alt-phenylene segments in the backbone, while their photoluminescence (PL spectra dominated by emissions from the fluorene excimer. For devices assembly ITO films were treated using a High Intensity Discharge Lamp (HPMVL without outer bulb presenting high ozone concentration than that conventional germicidal lamp. The device with ITO treated revealed significant decrease of threshold voltage (or turn-on voltage compared by untreated with I-V curves. This decrease can be related by water and carbon dioxide extracted on surface after UV-Ozone treatment revealed by DRIFT measurements.

White Polymer Light-Emitting Diodes Based on Exciplex Electroluminescence from Polymer Blends and a Single Polymer.

Science.gov (United States)

Liang, Junfei; Zhao, Sen; Jiang, Xiao-Fang; Guo, Ting; Yip, Hin-Lap; Ying, Lei; Huang, Fei; Yang, Wei; Cao, Yong

2016-03-09

In this Article, we designed and synthesized a series of polyfluorene derivatives, which consist of the electron-rich 4,4'-(9-alkyl-carbazole-3,6-diyl)bis(N,N-diphenylaniline) (TPA-Cz) in the side chain and the electron-deficient dibenzothiophene-5,5-dioxide (SO) unit in the main chain. The resulting copolymer PF-T25 that did not comprise the SO unit exhibited blue light-emission with the Commission Internationale de L'Eclairage coordinates of (0.16, 0.10). However, by physically blending PF-T25 with a blue light-emitting SO-based oligomer, a novel low-energy emission correlated to exciplex emerged due to the appropriate energy level alignment of TPA-Cz and the SO-based oligomers, which showed extended exciton lifetime as confirmed by time-resolved photoluminescent spectroscopy. The low-energy emission was also identified in copolymers consisting of SO unit in the main chain, which can effectively compensate for the high-energy emission to produce binary white light-emission. Polymer light-emitting diodes based on the exciplex-type single greenish-white polymer exhibit the peak luminous efficiency of 2.34 cd A(-1) and the maximum brightness of 12 410 cd m(-2), with Commission Internationale de L'Eclairage color coordinates (0.27, 0.39). The device based on such polymer showed much better electroluminescent stability than those based on blending films. These observations indicated that developing a single polymer with the generated exciplex emission can be a novel and effective molecular design strategy toward highly stable and efficient white polymer light-emitting diodes.

Improving Light Extraction of Organic Light-Emitting Devices by Attaching Nanostructures with Self-Assembled Photonic Crystal Patterns

Directory of Open Access Journals (Sweden)

Kai-Yu Peng

2014-01-01

Full Text Available A single-monolayered hexagonal self-assembled photonic crystal (PC pattern fabricated onto polyethylene terephthalate (PET films by using simple nanosphere lithography (NSL method has been demonstrated in this research work. The patterned nanostructures acted as a scattering medium to extract the trapped photons from substrate mode of optical-electronic device for improving the overall external quantum efficiency of the organic light-emitting diodes (OLEDs. With an optimum latex concentration, the distribution of self-assembled polystyrene (PS nanosphere patterns on PET films can be easily controlled by adjusting the rotation speed of spin-coater. After attaching the PS nanosphere array brightness enhancement film (BEF sheet as a photonic crystal pattern onto the device, the luminous intensity of OLEDs in the normal viewing direction is 161% higher than the one without any BEF attachment. The electroluminescent (EL spectrum of OLEDs with PS patterned BEF attachment also showed minor color offset and superior color stabilization characteristics, and thus it possessed the potential applications in all kinds of display technology and solid-state optical-electronic devices.

The effect of DCJTB doping concentration in PVK on the chromatic coordinate of electroluminescence

Energy Technology Data Exchange (ETDEWEB)

Zhang, F J; Xu, Z; Zhao, S L; Wang, L W; Yuan, G C [Key Laboratory of Luminescence and Optical Information (Beijing Jiaotong University), Ministry of Education (China); Zhao, D W [School of Electrical and Electronic Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore)], E-mail: fjzhang@bjtu.edu.cn

2008-05-15

The dominant mechanism of electroluminescence (EL) from 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) doped in poly-(N-vinyl-carbazole) (PVK) system was demonstrated to be a charge carrier trapped by DCJTB molecular rather than Foerster energy transfer from PVK to DCJTB. The chromatically coordinate EL emission of PVK:DCJTB changes from (0.41, 0.31) to (0.67, 0.31) with an increase in DCJTB doping concentration. The emission peak in DCJTB shows red-shift and the shoulder emission peak at 656 nm becomes stronger as the doping concentration increases. The effect of DCJTB doping concentration on EL spectra is attributed to strong dipole-dipole interaction between the DCJTB molecule with an increase in doping concentration.

Electroluminescence of a polythiophene molecular wire suspended between a metallic surface and the tip of a scanning tunneling microscope.

Science.gov (United States)

Reecht, Gaël; Scheurer, Fabrice; Speisser, Virginie; Dappe, Yannick J; Mathevet, Fabrice; Schull, Guillaume

2014-01-31

The electroluminescence of a polythiophene wire suspended between a metallic surface and the tip of a scanning tunneling microscope is reported. Under positive sample voltage, the spectral and voltage dependencies of the emitted light are consistent with the fluorescence of the wire junction mediated by localized plasmons. This emission is strongly attenuated for the opposite polarity. Both emission mechanism and polarity dependence are similar to what occurs in organic light emitting diodes (OLED) but at the level of a single molecular wire.

Pattern visual evoked potentials elicited by organic electroluminescence screen.

Science.gov (United States)

Matsumoto, Celso Soiti; Shinoda, Kei; Matsumoto, Harue; Funada, Hideaki; Sasaki, Kakeru; Minoda, Haruka; Iwata, Takeshi; Mizota, Atsushi

2014-01-01

To determine whether organic electroluminescence (OLED) screens can be used as visual stimulators to elicit pattern-reversal visual evoked potentials (p-VEPs). Checkerboard patterns were generated on a conventional cathode-ray tube (S710, Compaq Computer Co., USA) screen and on an OLED (17 inches, 320 × 230 mm, PVM-1741, Sony, Tokyo, Japan) screen. The time course of the luminance changes of each monitor was measured with a photodiode. The p-VEPs elicited by these two screens were recorded from 15 eyes of 9 healthy volunteers (22.0 ± 0.8 years). The OLED screen had a constant time delay from the onset of the trigger signal to the start of the luminescence change. The delay during the reversal phase from black to white for the pattern was 1.0 msec on the cathode-ray tube (CRT) screen and 0.5 msec on the OLED screen. No significant differences in the amplitudes of P100 and the implicit times of N75 and P100 were observed in the p-VEPs elicited by the CRT and the OLED screens. The OLED screen can be used as a visual stimulator to elicit p-VEPs; however the time delay and the specific properties in the luminance change must be taken into account.

Physical processes in thin-film electroluminescent structures based on ZnS:Mn showing self-organized patterns

International Nuclear Information System (INIS)

Zuccaro, S.; Raker, Th.; Niedernostheide, F.-J.; Kuhn, T.; Purwins, H.-G.

2003-01-01

Physical processes in thin ZnS:Mn films and their relation to the formation of dynamical patterns in the electroluminescence of AC driven films are investigated. The technique of photo-depolarization-spectroscopy is used to investigate defect states in these films and it is shown that specific features in the spectra correlate with the observed self-organized patterns. Furthermore, the time dependence of the dissipative current is measured at the same samples and compared with current waveforms obtained from numerical simulations of a drift-diffusion model. The results are used to discuss the origin of the self-organized processes in ZnS:Mn-films

Mixed-ligand Al complex—a new approach for more high efficient OLEDs

International Nuclear Information System (INIS)

Petrova, Petia K.; Tomova, Reni L.; Stoycheva-Topalova, Rumiana T.; Kaloyanova, Stefka S.; Deligeorgiev, Todor G.

2012-01-01

The mixed-ligand Aluminum bis(8-hydroxyquinoline) acetylacetonate (Alq 2 Acac) complex was presented and its performance as electroluminescent and electron transporting layer for OLED was studied. The photophysical properties of the novel complex were investigated and compared with the properties of the parent Alq 3 . Highly efficient OLED based on the mixed-ligand Al complex was developed with two times higher luminescence and efficiency compared to the identical OLED based on the conventional Alq 3 The better performance of the devices make the novel Al complex a very promising material for OLEDs. - Highlights: ► A novel electroluminescent Alq 2 Acac complex is presented as material for OLED. ► Electroluminescent emission of Alq 2 Acac is very similar to that of commercial Alq 3 . ► Devices with Alq 2 Acac show better characteristics compared to those with Alq 3 .

Influence of the polymer concentration on the electroluminescence of ZnO nanorod/polymer hybrid light emitting diodes

Science.gov (United States)

Zaman, Saima; Zainelabdin, Ahmed; Amin, Gul; Nur, Omer; Willander, Magnus

2012-09-01

The effects of the polymer concentration on the performance of hybrid light emitting diodes (LEDs) based on zinc oxide nanorods (ZnO NRs) and poly(9,9-dioctylfluorene) (PFO) were investigated. Various characterization techniques were applied to study the performance of the PFO/ZnO NR hybrid LEDs fabricated with various PFO concentrations. The fabricated hybrid LEDs demonstrated stable rectifying diode behavior, and it was observed that the turn-on voltage of the LEDs is concentration dependent. The measured room temperature electroluminescence (EL) showed that the PFO concentration plays a critical role in the emission spectra of the hybrid LEDs. At lower PFO concentrations of 2-6 mg/ml, the EL spectra are dominated by blue emission. However, by increasing the concentration to more than 8 mg/ml, the blue emission was completely suppressed while the green emission was dominant. This EL behavior was explained by a double trap system of excitons that were trapped in the β-phase and/or in the fluorenone defects in the PFO side. The effects of current injection on the hybrid LEDs and on the EL emission were also investigated. Under a high injection current, a new blue peak was observed in the EL spectrum, which was correlated to the creation of a new chemical species on the PFO chain. The green emission peak was also enhanced with increasing injection current because of the fluorenone defects. These results indicate that the emission spectra of the hybrid LEDs can be tuned by using different polymer concentrations and by varying the current injected into the device.

Simple synthesis, photophysics, and electroluminescent properties of poly[2,7-bis(4-tert-butylstyryl)fluorene-9,9-diyl-alt-alkane-.alpha.,.omega.-diyl

Czech Academy of Sciences Publication Activity Database

Mikroyannidis, J. A.; Barberis, V. P.; Výprachtický, Drahomír; Cimrová, Věra

2007-01-01

Roč. 45, č. 5 (2007), s. 809-821 ISSN 0887-624X R&D Projects: GA MŠk(CZ) 1M06031; GA AV ČR IAA4050409; GA ČR GA203/04/1372 Institutional research plan: CEZ:AV0Z40500505 Keywords : distyrylfluorene * electrochemical properties * electroluminescence Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.529, year: 2007

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile

International Nuclear Information System (INIS)

Chew Siewling; Wang Pengfei; Hong Zirou; Kwong, H.L.; Tang Jianxin; Sun Shiling; Lee, C.S.; Lee, S.-T.

2007-01-01

A new compound with intramolecular charge transfer (ICT) property-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both 'positive' and 'negative' solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N'-diphenyl-N,N'-bis-(3-methylphenyl) (1,1'-diphenyl)4,4'-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m 2 at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m 2 at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m 2 at 4.5 V, a maximum brightness of 12600 cd/m 2 at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile

Energy Technology Data Exchange (ETDEWEB)

Chew Siewling [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Wang Pengfei [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100101 (China)]. E-mail: wangpf@mail.ipc.ac.cn; Hong Zirou [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Kwong, H.L. [Department of Biology and Chemistry, City University of Hong Kong, Hong Kong (China); Tang Jianxin [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Sun Shiling [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, C.S. [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)]. E-mail: apcslee@cityu.edu.hk; Lee, S.-T. [Center of Super-Diamond and Advanced Films (COSDAF) and Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)]. E-mail: apannale@cityu.edu.hk

2007-06-15

A new compound with intramolecular charge transfer (ICT) property-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl] -pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both 'positive' and 'negative' solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N'-diphenyl-N,N'-bis-(3-methylphenyl) (1,1'-diphenyl)4,4'-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m{sup 2} at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m{sup 2} at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m{sup 2} at 4.5 V, a maximum brightness of 12600 cd/m{sup 2} at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.

Photoluminescent (PL) or electroluminescent (EL) quantum dots for display, lighting, and photomedicine (Conference Presentation)

Science.gov (United States)

Dong, Yajie

2017-02-01

Quantum dots (QDs) have gone through a long journey before finding their ways into the display field. This talk will briefly touch on the history before trying to answer several key questions related to QDs applications in display: What are QDs? How are they made? What properties do they have and Why? How can these properties be used to improve color and efficiency of display, in either photoluminescence (PL) or electroluminescence (EL) mode? And what are the remaining challenges for QDs wide adoption in display industry? Lastly, some most recent progresses in our UCF lab at both PL and EL fronts will be highlighted. For PL, a cadmium-free perovskite-polymer composite films with exceptionally narrow emission green peaks (FWHM 20 nm) and good water and thermal stability will be reported. Together with red quantum dots or PFS/KSF phosphors as down-converters for blue LEDs, a white-light source with 95% Rec. 2020 color gamut was demonstrated [1]. For EL, red quantum dot light emitting devices (QLEDs) with record luminance of 165,000 Cd/m2 has been obtained at a current density of 1000 mA/cm2 with a low driving voltage of 5.8 V and CIE coordinates of (0.69, 0.31). [2] The potential of using these QLEDs for light sources for integrated sensing platform [3] or high efficiency, high color quality hybrid white OLED [4] will be discussed. [1] Y. N. Wang, J. He, H. Chen, J. S. Chen, R. D. Zhu, P. Ma, A. Towers, Y. Lin, A. J. Gesquiere, S. T. Wu, Y. J. Dong. Ultrastable, Highly Luminescent Organic-Inorganic Perovskite - Polymer Composite Films, Advanced Materials, accepted, (2016). [2] Y. J. Dong, J.M. Caruge, Z. Q. Zhou, C. Hamilton, Z. Popovic, J. Ho, M. Stevenson, G. Liu, V. Bulovic, M. Bawendi, P. T. Kazlas, S. Coe-Sullivan, and J. Steckel Ultra-bright, Highly Efficient, Low Roll-off Inverted Quantum-Dot Light Emitting Devices (QLEDs). SID Symp. Dig. Tech. Pap. 46, 270-273 (2015). [3] J. He, H. Chen, S. T. Wu, and Y. J. Dong, Integrated Sensing Platform Based on Quantum

A photovoltaic module diagnostic setup for lock-in-thermography and lock-in electroluminescence imaging

DEFF Research Database (Denmark)

Parikh, Harsh; Spataru, Sergiu; Sera, Dezso

2018-01-01

Electroluminescence (EL) imaging and infrared (IRT) thermography techniques have become indispensable tools in recent years for health diagnostic of PV modules in solar industry application. Complementary to these imaging methods, lock-in techniques can effectively remove noise by periodically...... modulating the input signal and averaging it over a desired number of periods. We propose a combined lock-in EL and lock-in IRT diagnostic setup for accurate analysis of different types of faults occurring in a solar module. The setup is built around a Goldeye CL-033 high-speed SWIR camera, which can acquire...... experimental work on a (36/72) cell solar module using combined (EL) or (IRT) lock-in-thermography. The setup allows one to investigate the different technological problems that can occur when performing PV diagnostics in drone-based inspections....

Emitting materials based on phenylanthracene-substituted naphthalene derivatives for organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyun Woo; Kim, Hye Jeong; Kim, Young Seok; Kim, Jwajin [Department of Chemistry, Sungkyunkwan University, Suwon 440‐746 (Korea, Republic of); Lee, Song Eun; Lee, Ho Won [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@wow.hongik.ac.kr [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon 440‐746 (Korea, Republic of)

2015-09-15

This study reports the emitting materials based on phenylanthracene-substituted naphthalene derivatives to achieve efficient electroluminescent properties for OLED applications. An OLED device using 4,4′-bis(10-phenylanthracen-9-yl)-1,1′-binaphthalene exhibited the blue emission with the CIE coordinates of (0.19, 0.16) and efficient electroluminescent properties with the luminance, power and external quantum efficiency of 1.70 cd/A, 0.79 lm/W and 1.26% at 20 mA/cm{sup 2}, respectively. Also, the other device using 1,4-bis(10-phenylanthracene-9-yl)naphthalene exhibited white emission with the CIE coordinates of (0.34, 0.43) at 7V, respectively. This device exhibits the luminance, power and external quantum efficiency of 2.22 cd/A, 1.13 lm/W and 0.86% at 20 mA/cm{sup 2}, respectively. - Highlights: • We synthesized fluorescent materials based on phenylanthracene derivatives. • Electroluminescence properties of these materials depend on the molecular structures. • These blue and white materials have great potential for application in OLEDs.

Polymer light emitting diodes

International Nuclear Information System (INIS)

Gautier-Thianche, Emmmanuelle

1998-01-01

We study sandwich type semiconducting polymer light emitting diodes; anode/polymer/cathode. ITO is selected as anode, this polymer is a blend of a commercially available polymer with a high hole transport ability: polyvinyl-carbazole and a laser dye: coumarin-515. Magnesium covered with silver is chosen for the anode. We study the influence of polymer thickness and coumarin doping ratio on electroluminescence spectrum, electric characteristics and quantum efficiency. An important drawback is that diodes lifetime remains low. In the second part of our study we determine degradations causes with X-Ray reflectivity experiments. It may be due to ITO very high roughness. We realize a new type of planar electroluminescent device: a channel type electroluminescent device in which polymer layer is inserted into an aluminium channel. Such a device is by far more stable than using classical sandwich structures with the same polymer composition: indeed, charges are generated by internal-field ionization and there is no injection from the electrode to the polymer. This avoids electrochemical reactions at electrodes, thus reducing degradations routes. (author) [fr

Emitting materials based on phenylanthracene-substituted naphthalene derivatives for organic light-emitting diodes

International Nuclear Information System (INIS)

Lee, Hyun Woo; Kim, Hye Jeong; Kim, Young Seok; Kim, Jwajin; Lee, Song Eun; Lee, Ho Won; Kim, Young Kwan; Yoon, Seung Soo

2015-01-01

This study reports the emitting materials based on phenylanthracene-substituted naphthalene derivatives to achieve efficient electroluminescent properties for OLED applications. An OLED device using 4,4′-bis(10-phenylanthracen-9-yl)-1,1′-binaphthalene exhibited the blue emission with the CIE coordinates of (0.19, 0.16) and efficient electroluminescent properties with the luminance, power and external quantum efficiency of 1.70 cd/A, 0.79 lm/W and 1.26% at 20 mA/cm 2 , respectively. Also, the other device using 1,4-bis(10-phenylanthracene-9-yl)naphthalene exhibited white emission with the CIE coordinates of (0.34, 0.43) at 7V, respectively. This device exhibits the luminance, power and external quantum efficiency of 2.22 cd/A, 1.13 lm/W and 0.86% at 20 mA/cm 2 , respectively. - Highlights: • We synthesized fluorescent materials based on phenylanthracene derivatives. • Electroluminescence properties of these materials depend on the molecular structures. • These blue and white materials have great potential for application in OLEDs

Single-crystal perovskite CH3NH3PbBr3 prepared by cast capping method for light-emitting diodes

Science.gov (United States)

Nguyen, Van-Cao; Katsuki, Hiroyuki; Sasaki, Fumio; Yanagi, Hisao

2018-04-01

In this study, electroluminescence from single crystals of CH3NH3PbBr3 perovskite is explored. The cast capping method was applied to fabricate simple devices with an ITO/CH3NH3PbBr3/ITO structure. The devices showed a low operation voltage of 2 V and a pure green luminescence with full width at half maximum of ∼20 nm. However, the emission occurring at the crystal edges demonstrated blinking with a subsecond time interval, which is similar to the previously reported photoluminescence behavior of nanocrystal perovskites. This electroluminescence blinking may provide new insight into the recombination processes depending on the carrier traps and defects of emission layers in perovskite light-emitting devices.

Enhanced luminescence of MEH-PPV through the reduction of chain aggregations by blending 4-cyano-4′-N-heptylbiphenyl

Energy Technology Data Exchange (ETDEWEB)

Hsu, Kuei-Ting [Institute of Organic and Polymeric Materials, National Taipei University of Technology, No.1, Section 3, Zhongxiao E. Rd., Da’an Dist., Taipei City 106, Taiwan (R.O.C.) (China); Department of Chemical Engineering, Army Academy, No.750, Longdong Rd., Chung-Li 320, Taiwan (R.O.C.) (China); Chang, Shu-Mei; Li, Guo-Yuan [Institute of Organic and Polymeric Materials, National Taipei University of Technology, No.1, Section 3, Zhongxiao E. Rd., Da’an Dist., Taipei City 106, Taiwan (R.O.C.) (China); Liu, Wei-Ren, E-mail: WRLiu1203@gmail.com [Department of Chemical Engineering, R and D Center for Membrane Center, Chung Yuan Christian University, Chung Li, Taiwan (China)

2015-02-15

In this study, we report the electroluminescence and photoluminescence of poly[2-methoxy-5-(2-ethylhexyloxy)-p-phenylene vinylene] (MEH-PPV) and 4-cyano-4′-N-heptylbiphenyl (7CB) blends in the ratios of 0–90 wt% by drop-coating processes. The corresponding characterization of polarized optical microscope, electroluminescence, photoluminescence and atomic force microscope of different blending ratios of MEH-PPV/7CB are systematically carried out in this study. The optimal composition of 6/4 ratio in MEH-PPV/7CB exhibit the highest luminescence, which is almost ten times than that of pure MEH-PPV due to the fact that 7CB could be a barrier to avoid the aggression of MEH-PPV. The novel blending system demonstrate a potential approach for synthesizing the MEH-PPV/7CB composite film for electroluminescent device applications. - Highlights: • We propose a novel blending system of MEH-PPV/7CB system. • Controlling the alignment of polymer. • Avoid the aggression of MEH-PPV. • The luminescence intensity of blend film can be enhanced by 10 times. • A potential approach for electroluminescent device applications.

Low driving voltage simplified tandem organic light-emitting devices by using exciplex-forming hosts

Science.gov (United States)

Zhou, Dong-Ying; Cui, Lin-Song; Zhang, Ying-Jie; Liao, Liang-Sheng; Aziz, Hany

2014-10-01

Tandem organic light-emitting devices (OLEDs), i.e., OLEDs containing multiple electroluminescence (EL) units that are vertically stacked, are attracting significant interest because of their ability to realize high current efficiency and long operational lifetime. However, stacking multiple EL units in tandem OLEDs increases driving voltage and complicates fabrication process relative to their standard single unit counterparts. In this paper, we demonstrate low driving voltage tandem OLEDs via utilizing exciplex-forming hosts in the EL units instead of conventional host materials. The use of exciplex-forming hosts reduces the charge injection barriers and the trapping of charges on guest molecules, resulting in the lower driving voltage. The use of exciplex-forming hosts also allows using fewer layers, hence simpler EL configuration which is beneficial for reducing the fabrication complexity of tandem OLEDs.

Investigation of CaTiO3:Pr3+ thin films deposited by radiofrequency reactive magnetron sputtering for electroluminescence application

International Nuclear Information System (INIS)

Sarakha, L; Bousquet, A; Tomasella, E; Boutinaud, P; Mahiou, R

2010-01-01

In this report we successfully deposited thin films of CaTiO 3 :Pr 3+ by radiofrequency magnetron sputtering. The films were studied and we tried to understand the evolution of their optical and electrical properties. We noticed that the annealing temperature and the deposition pressures have an important influence on these properties. Thin films with good optical and electrical properties have been obtained. These films are transparent and are characterized by an intense red photoluminescence and a low fixed charge density. They are well dedicated for electroluminescence purposes.

Two-band superlinear electroluminescence in GaSb based nanoheterostructures with AlSb/InAs.sub.1-x./sub.Sb.sub.x./sub./AlSb deep quantum well

Czech Academy of Sciences Publication Activity Database

Mikhailova, M. P.; Ivanov, E.V.; Danilov, L.V.; Petukhov, A.A.; Kalinina, K.V.; Slobozhanyuk, S.I.; Zegrya, G.G.; Stoyanov, N. D.; Yakovlev, Yu. P.; Hospodková, Alice; Pangrác, Jiří; Oswald, Jiří; Zíková, Markéta; Hulicius, Eduard

2014-01-01

Roč. 115, č. 22 (2014), "223102-1"-"223102-5" ISSN 0021-8979 R&D Projects: GA ČR GA13-15286S Institutional support: RVO:68378271 Keywords : MOVPE * GaSb * InAs * electroluminescence * quantum well Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.183, year: 2014

Pattern Visual Evoked Potentials Elicited by Organic Electroluminescence Screen

Directory of Open Access Journals (Sweden)

Celso Soiti Matsumoto

2014-01-01

Full Text Available Purpose. To determine whether organic electroluminescence (OLED screens can be used as visual stimulators to elicit pattern-reversal visual evoked potentials (p-VEPs. Method. Checkerboard patterns were generated on a conventional cathode-ray tube (S710, Compaq Computer Co., USA screen and on an OLED (17 inches, 320 × 230 mm, PVM-1741, Sony, Tokyo, Japan screen. The time course of the luminance changes of each monitor was measured with a photodiode. The p-VEPs elicited by these two screens were recorded from 15 eyes of 9 healthy volunteers (22.0 ± 0.8 years. Results. The OLED screen had a constant time delay from the onset of the trigger signal to the start of the luminescence change. The delay during the reversal phase from black to white for the pattern was 1.0 msec on the cathode-ray tube (CRT screen and 0.5 msec on the OLED screen. No significant differences in the amplitudes of P100 and the implicit times of N75 and P100 were observed in the p-VEPs elicited by the CRT and the OLED screens. Conclusion. The OLED screen can be used as a visual stimulator to elicit p-VEPs; however the time delay and the specific properties in the luminance change must be taken into account.

[Effects of white organic light-emitting devices using color conversion films on electroluminescence spectra].

Science.gov (United States)

Hou, Qing-Chuan; Wu, Xiao-Ming; Hua, Yu-Lin; Qi, Qing-Jin; Li, Lan; Yin, Shou-Gen

2010-06-01

The authors report a novel white organic light-emitting device (WOLED), which uses a strategy of exciting organic/ inorganic color conversion film with a blue organic light-emitting diode (OLED). The luminescent layer of the blue OLED was prepared by use of CBP host blended with a blue highly fluorescent dye N-BDAVBi. The organic/inorganic color conversion film was prepared by dispersing a mixture of red pigment VQ-D25 and YAG : Ce3+ phosphor in PMMA. The authors have achieved a novel WOLED with the high color stability by optimizing the thickness and fluorescent pigment concentration of the color conversion film. When the driving voltage varied between 6 and 14 V, the color coordinates (CIE) varied slightly from (0.354, 0.304) to (0.357, 0.312) and the maximum current efficiency is about 5.8 cd x A(-1) (4.35 mA x cm(-2)), the maximum brightness is 16 800 cd x m(-2) at the operating voltage of 14 V.

Room Temperature Electroluminescence from Tensile-Strained Si0.13Ge0.87/Ge Multiple Quantum Wells on a Ge Virtual Substrate

Directory of Open Access Journals (Sweden)

Guangyang Lin

2016-09-01

Full Text Available Direct band electroluminescence (EL from tensile-strained Si0.13Ge0.87/Ge multiple quantum wells (MQWs on a Ge virtual substrate (VS at room temperature is reported herein. Due to the competitive result of quantum confinement Stark effect and bandgap narrowing induced by tensile strain in Ge wells, electroluminescence from Γ1-HH1 transition in 12-nm Ge wells was observed at around 1550 nm. As injection current density increases, additional emission shoulders from Γ2-HH2 transition in Ge wells and Ge VS appeared at around 1300–1400 nm and 1600–1700 nm, respectively. The peak energy of EL shifted to the lower energy side superquadratically with an increase of injection current density as a result of the Joule heating effect. During the elevation of environmental temperature, EL intensity increased due to a reduction of energy between L and Γ valleys of Ge. Empirical fitting of the relationship between the integrated intensity of EL (L and injection current density (J with L~Jm shows that the m factor increased with injection current density, suggesting higher light emitting efficiency of the diode at larger injection current densities, which can be attributed to larger carrier occupations in the Γ valley and the heavy hole (HH valance band at higher temperatures.

Hybrid white organic light-emitting devices consisting of a non-doped thermally activated delayed fluorescent emitter and an ultrathin phosphorescent emitter

International Nuclear Information System (INIS)

Zhao, Juan; Wang, Zijun; Wang, Run; Chi, Zhenguo; Yu, Junsheng

2017-01-01

Hybrid white organic light-emitting devices (OLEDs) are fabricated by employing non-doped emitting layers (EMLs), which are consisted of a blue thermally activated delayed fluorescent (TADF) emitter 9,9-dimethyl-9,10-dihydroacridine-diphenylsulfone (DMAC-DPS) and an ultrathin yellow iridium complex bis[2-(4-tertbutylphenyl)benzothiazolato-N,C 2′ ] iridium (acetylacetonate) [(tbt) 2 Ir(acac)]. With thickness optimization of DMAC-DPS, a white OLED achieves maximum current efficiency, power efficiency and external quantum efficiency of 34.9 cd/A, 29.2 lm/W and 11.4%, respectively, as well as warm white emission with relatively stable electroluminescence spectra. The results suggest that, bipolar charge carrier transport property and concentration independent property of DMAC-DPS, charge carrier trapping effect of the ultrathin (tbt) 2 Ir(acac), and balanced self-emission process and energy transfer process between DMAC-DPS and (tbt) 2 Ir(acac), contribute to high device performance.

Recent Advances in Conjugated Polymers for Light Emitting Devices

Science.gov (United States)

AlSalhi, Mohamad Saleh; Alam, Javed; Dass, Lawrence Arockiasamy; Raja, Mohan

2011-01-01

A recent advance in the field of light emitting polymers has been the discovery of electroluminescent conjugated polymers, that is, kind of fluorescent polymers that emit light when excited by the flow of an electric current. These new generation fluorescent materials may now challenge the domination by inorganic semiconductor materials of the commercial market in light-emitting devices such as light-emitting diodes (LED) and polymer laser devices. This review provides information on unique properties of conjugated polymers and how they have been optimized to generate these properties. The review is organized in three sections focusing on the major advances in light emitting materials, recent literature survey and understanding the desirable properties as well as modern solid state lighting and displays. Recently, developed conjugated polymers are also functioning as roll-up displays for computers and mobile phones, flexible solar panels for power portable equipment as well as organic light emitting diodes in displays, in which television screens, luminous traffic, information signs, and light-emitting wallpaper in homes are also expected to broaden the use of conjugated polymers as light emitting polymers. The purpose of this review paper is to examine conjugated polymers in light emitting diodes (LEDs) in addition to organic solid state laser. Furthermore, since conjugated polymers have been approved as light-emitting organic materials similar to inorganic semiconductors, it is clear to motivate these organic light-emitting devices (OLEDs) and organic lasers for modern lighting in terms of energy saving ability. In addition, future aspects of conjugated polymers in LEDs were also highlighted in this review. PMID:21673938

Automatic Detection and Evaluation of Solar Cell Micro-Cracks in Electroluminescence Images Using Matched Filters

Energy Technology Data Exchange (ETDEWEB)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2016-11-21

A method for detecting micro-cracks in solar cells using two dimensional matched filters was developed, derived from the electroluminescence intensity profile of typical micro-cracks. We describe the image processing steps to obtain a binary map with the location of the micro-cracks. Finally, we show how to automatically estimate the total length of each micro-crack from these maps, and propose a method to identify severe types of micro-cracks, such as parallel, dendritic, and cracks with multiple orientations. With an optimized threshold parameter, the technique detects over 90 % of cracks larger than 3 cm in length. The method shows great potential for quantifying micro-crack damage after manufacturing or module transportation for the determination of a module quality criterion for cell cracking in photovoltaic modules.

First proof of topological signature in high pressure xenon gas with electroluminescence amplification

CERN Document Server

Ferrario, P.; López-March, N.; Gómez-Cadenas, J.J.; Álvarez, V.; Azevedo, C.D.R.; Borges, F.I.G.; Cárcel, S.; Cebrián, S.; Cervera, A.; Conde, C.A.N.; Dafni, T.; Díaz, J.; Diesburg, M.; Esteve, R.; Fernandes, L.M.P.; Ferreira, A.L.; Freitas, E.D.C.; Gehman, V.M.; Goldschmidt, A.; González-Díaz, D.; Gutiérrez, R.M.; Hauptman, J.; Henriques, C.A.O.; Hernando Morata, J.A.; Irastorza, I.G.; Labarga, L.; Lebrun, P.; Liubarsky, I.; Lorca, D.; Losada, M.; Luzón, G.; Marí, A.; Martín-Albo, J.; Martínez-Lema, G.; Martínez, A.; Miller, T.; Monrabal, F.; Monserrate, M.; Monteiro, C.M.B.; Mora, F.J.; Moutinho, L.M.; Muñoz Vidal, J.; Nebot-Guinot, M.; Novella, P.; Nygren, D.; Para, A.; Pérez, J.; Pérez Aparicio, J.L.; Querol, M.; Renner, J.; Ripoll, L.; Rodríguez, J.; Santos, F.P.; dos Santos, J.M.F.; Serra, L.; Shuman, D.; Simón, A.; Sofka, C.; Sorel, M.; Toledo, J.F.; Torrent, J.; Tsamalaidze, Z.; Veloso, J.F.C.A.; Villar, J.A.; Webb, R.; White, J.T.; Yahlali, N.; Yepes-Ramírez, H.

2016-01-01

The NEXT experiment aims to observe the neutrinoless double beta decay of xenon in a high-pressure Xe136 gas TPC using electroluminescence (EL) to amplify the signal from ionization. One of the main advantages of this technology is the possibility to reconstruct the topology of events with energies close to Qbb. This paper presents the first demonstration that the topology provides extra handles to reject background events using data obtained with the NEXT-DEMO prototype. Single electrons resulting from the interactions of Na22 1275 keV gammas and electron-positron pairs produced by conversions of gammas from the Th228 decay chain were used to represent the background and the signal in a double beta decay. These data were used to develop algorithms for the reconstruction of tracks and the identification of the energy deposited at the end-points, providing an extra background rejection factor of 24.3 +- 1.4 (stat.)%, while maintaining an efficiency of 66.7 +- 0.6 (stat.)% for signal events.

Room-temperature near-infrared electroluminescence from boron-diffused silicon pn junction diodes

Directory of Open Access Journals (Sweden)

Si eLi

2015-02-01

Full Text Available Silicon pn junction diodes with different doping concentrations were prepared by boron diffusion into Czochralski (CZ n-type silicon substrate. Their room-temperature near-infrared electroluminescence (EL was measured. In the EL spectra of the heavily boron doped diode, a luminescence peak at ~1.6 m (0.78 eV was observed besides the band-to-band line (~1.1eV under the condition of high current injection, while in that of the lightly boron doped diode only the band-to-band line was observed. The intensity of peak at 0.78 eV increases exponentially with current injection with no observable saturation at room temperature. Furthermore, no dislocations were found in the cross-sectional transmission electron microscopy image, and no dislocation-related luminescence was observed in the low-temperature photoluminescence spectra. We deduce the 0.78 eV emission originates from the irradiative recombination in the strain region of diodes caused by the diffusion of large number of boron atoms into silicon crystal lattice.

All-Quantum-Dot Infrared Light-Emitting Diodes

KAUST Repository

Yang, Zhenyu

2015-12-22

© 2015 American Chemical Society. Colloidal quantum dots (CQDs) are promising candidates for infrared electroluminescent devices. To date, CQD-based light-emitting diodes (LEDs) have employed a CQD emission layer sandwiched between carrier transport layers built using organic materials and inorganic oxides. Herein, we report the infrared LEDs that use quantum-tuned materials for each of the hole-transporting, the electron-transporting, and the light-emitting layers. We successfully tailor the bandgap and band position of each CQD-based component to produce electroluminescent devices that exhibit emission that we tune from 1220 to 1622 nm. Devices emitting at 1350 nm achieve peak external quantum efficiency up to 1.6% with a low turn-on voltage of 1.2 V, surpassing previously reported all-inorganic CQD LEDs.

Mixed-ligand Al complex-a new approach for more high efficient OLEDs

Energy Technology Data Exchange (ETDEWEB)

Petrova, Petia K., E-mail: petia@clf.bas.bg [Institute of Optical Materials and Technologies ' Acad. J. Malinowski' , Bulgarian Academy of Sciences, Acad. G Bonchev st., bl. 109, 1113 Sofia (Bulgaria); Tomova, Reni L.; Stoycheva-Topalova, Rumiana T. [Institute of Optical Materials and Technologies ' Acad. J. Malinowski' , Bulgarian Academy of Sciences, Acad. G Bonchev st., bl. 109, 1113 Sofia (Bulgaria); Kaloyanova, Stefka S.; Deligeorgiev, Todor G. [Applied Organic Chemistry, Faculty of Chemistry, University of Sofia, Sofia 1164 (Bulgaria)

2012-02-15

The mixed-ligand Aluminum bis(8-hydroxyquinoline) acetylacetonate (Alq{sub 2}Acac) complex was presented and its performance as electroluminescent and electron transporting layer for OLED was studied. The photophysical properties of the novel complex were investigated and compared with the properties of the parent Alq{sub 3}. Highly efficient OLED based on the mixed-ligand Al complex was developed with two times higher luminescence and efficiency compared to the identical OLED based on the conventional Alq{sub 3} The better performance of the devices make the novel Al complex a very promising material for OLEDs. - Highlights: Black-Right-Pointing-Pointer A novel electroluminescent Alq{sub 2}Acac complex is presented as material for OLED. Black-Right-Pointing-Pointer Electroluminescent emission of Alq{sub 2}Acac is very similar to that of commercial Alq{sub 3}. Black-Right-Pointing-Pointer Devices with Alq{sub 2}Acac show better characteristics compared to those with Alq{sub 3}.

Improved performances of red organic light-emitting devices by co-doping a rubrene derivative and DCJTB into tris-(8-hydroxyquinoline) aluminum host

Energy Technology Data Exchange (ETDEWEB)

Li Tianle [Physics Department, School of Science, Maoming University, Maoming 525000 (China); Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Li Wenlian, E-mail: wllioel@yahoo.com.c [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Li Xiao [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Chu Bei, E-mail: beichubox@hotmail.co [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Su Zisheng; Han Liangliang; Chen Yiren [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Hu Zhizhi; Zhang Zhiqiang [Optic Photo-Electronic Materials and Research Development Center, Liaoning University of Science and Technology, Anshan 114044 (China)

2010-10-15

Performances of red organic light-emitting device were improved by co-doping 2-formyl-5,6,11,12-tetraphenylnaphthacene (2FRb) and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetra-methyljulolidyl-9-enyl) -4H-pyran (DCJTB) in tris-(8-hydroxyquinoline) aluminum (Alq{sub 3}) host as the emitting layer. The device with 1 wt% DCJTB and 2.4 w% 2FRb in Alq{sub 3} host gave a saturated red emission with CIE chromaticity coordinates of (0.65, 0.35) and a maximum current efficiency as high as 6.45 cd/A, which are 2 and 2.4 fold larger than that of the device with 1 wt% DCJTB (3.28 cd/A) in Alq{sub 3} host and the device with 2.4 wt% 2FRb (2.72 cd/A) in Alq{sub 3} host at the current density of 20 mA/cm{sup 2}, respectively. The improvement could be attributed to the effective utilization of host energy by both energy transfer and trapping in the electroluminescence process and the depression of concentration quenching between the dopants molecules.

Reactive Chemical Vapor Deposition Method as New Approach for Obtaining Electroluminescent Thin Film Materials

Directory of Open Access Journals (Sweden)

Valentina V. Utochnikova

2012-01-01

Full Text Available The new reactive chemical vapor deposition (RCVD method has been proposed for thin film deposition of luminescent nonvolatile lanthanide aromatic carboxylates. This method is based on metathesis reaction between the vapors of volatile lanthanide dipivaloylmethanate (Ln(dpm3 and carboxylic acid (HCarb orH2Carb′ and was successfully used in case of HCarb. Advantages of the method were demonstrated on example of terbium benzoate (Tb(bz3 and o-phenoxybenzoate thin films, and Tb(bz3 thin films were successfully examined in the OLED with the following structure glass/ITO/PEDOT:PSS/TPD/Tb(bz3/Ca/Al. Electroluminescence spectra of Tb(bz3 showed only typical luminescent bands, originated from transitions of the terbium ion. Method peculiarities for deposition of compounds of dibasic acids H2Carb′ are established on example of terbium and europium terephtalates and europium 2,6-naphtalenedicarboxylate.

Two-phase Cryogenic Avalanche Detector with electroluminescence gap operated in argon doped with nitrogen

Energy Technology Data Exchange (ETDEWEB)

Bondar, A.; Buzulutskov, A. [Budker Institute of Nuclear Physics SB RAS, Lavrentiev avenue 11, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, Pirogov street 2, 630090 Novosibirsk (Russian Federation); Dolgov, A. [Novosibirsk State University, Pirogov street 2, 630090 Novosibirsk (Russian Federation); Nosov, V.; Shekhtman, L.; Shemyakina, E.; Sokolov, A. [Budker Institute of Nuclear Physics SB RAS, Lavrentiev avenue 11, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, Pirogov street 2, 630090 Novosibirsk (Russian Federation)

2017-02-11

A two-phase Cryogenic Avalanche Detector (CRAD) with electroluminescence (EL) gap, operated in argon doped with a minor (49±7 ppm) admixture of nitrogen, has been studied. The EL gap was optically read out using cryogenic PMTs located on the perimeter of the gap. We present the results of the measurements of the N{sub 2} content, detector sensitivity to X-ray-induced signals, EL gap yield and electron lifetime in the liquid. The detector sensitivity, at a drift field in liquid Ar of 0.6 kV/cm, was measured to be 9 and 16 photoelectrons recorded at the PMTs per keV of deposited energy at 23 and 88 keV respectively. Such two-phase detectors, with enhanced sensitivity to the S2 (ionization-induced) signal, are relevant in the field of argon detectors for dark matter search and low energy neutrino detection.

2D Semiconductors for Valley-Polarized LEDs and Photodetectors

Science.gov (United States)

Yu, Ting

The recently discovered two-dimensional (2D) semiconductors, such as transitional-metal-dichalcogenide monolayers, have aroused great interest due to the underlying quantum physics and the appealing optoelectronic applications like atomically thin light-emitting diodes (LEDs) and photodetectors. On the one hand, valley-polarized electroluminescence and photocurrent from such monolayers have not caused enough attention but highly demanded as building blocks for the new generation valleytronic applications. On the other hand, most reports on these devices are based on the mechanically exfoliated small samples. Considering real applications, a strategy which could offer mass-product and high compatibility to the current planar processes is greatly demanded. Large-area samples prepared by chemical vapour deposition (CVD) are perfect candidates towards such a goal. Here, we report electrically tunable valley-polarized electroluminescence and the selective spin-valley-coupled photocurrent in optoelectronic devices based on monolayer WS2 and MoS2 grown by CVD, exhibiting large electroluminescence and photocurrent dichroisms of 81% and 60%, respectively. The controllable valley polarization and emission components of the electroluminescence have been realized by varying electrical injection of carriers. For the observed helicity-dependent photocurrent, the circular photogalvanic effect at resonant excitations has been found to take the dominant responsibility.

New cyclometalated Iridium(III) beta-dicetone complex as phosphorescent dopant in Organic light emitting devices

Science.gov (United States)

Ivanov, P.; Petrova, P.; Stanimirov, S.; Tomova, R.

2017-01-01

A new Bis[4-(benzothiazolato-N,C2‧-2-yl)-N,N-dimethylaniline]Iridium(III) acetylacetonate (Me2N-bt) 2Ir(acac) was synthesized and identified by 1H NMR and elemental analysis. The application of the new compound as a dopant in the hole transporting layer (HTL) of Organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was N,N’-bis(3-methylphenyl)-N,N’-diphenylbenzidine (TPD), incorporated in Poly(N-vinylcarbazole) (PVK) matrix, EL - electroluminescent layer of Bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy)aluminum (BAlq) and ETL - electron-transporting layer of Tris-(8-hydroxyquinoline) aluminum (Alq3) or Bis[2-(2-benzothiazoly) phenolato]zinc (Zn(btz)2). We established that the electroluminescent spectra of OLEDs at different concentrations of the dopant were basically the sum of the greenish-blue emission of BAlq and yellowish-green emission of Ir complex. It was found that with increasing of the dopant concentration the relative electroluminescent intensity of Iridium complex emission increased and this of BAlq decreased and as a result the fine tuning of OLED color was observed.

Hybrid white organic light-emitting devices consisting of a non-doped thermally activated delayed fluorescent emitter and an ultrathin phosphorescent emitter

Energy Technology Data Exchange (ETDEWEB)

Zhao, Juan [State Key Laboratory of Electronic Thin Film and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China, Chengdu 610054 (China); School of Chemistry, Sun Yat-sen University, Guangzhou 510275 (China); Wang, Zijun; Wang, Run [State Key Laboratory of Electronic Thin Film and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China, Chengdu 610054 (China); Chi, Zhenguo, E-mail: chizhg@mail.sysu.edu.cn [School of Chemistry, Sun Yat-sen University, Guangzhou 510275 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Film and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2017-04-15

Hybrid white organic light-emitting devices (OLEDs) are fabricated by employing non-doped emitting layers (EMLs), which are consisted of a blue thermally activated delayed fluorescent (TADF) emitter 9,9-dimethyl-9,10-dihydroacridine-diphenylsulfone (DMAC-DPS) and an ultrathin yellow iridium complex bis[2-(4-tertbutylphenyl)benzothiazolato-N,C{sup 2′}] iridium (acetylacetonate) [(tbt){sub 2}Ir(acac)]. With thickness optimization of DMAC-DPS, a white OLED achieves maximum current efficiency, power efficiency and external quantum efficiency of 34.9 cd/A, 29.2 lm/W and 11.4%, respectively, as well as warm white emission with relatively stable electroluminescence spectra. The results suggest that, bipolar charge carrier transport property and concentration independent property of DMAC-DPS, charge carrier trapping effect of the ultrathin (tbt){sub 2}Ir(acac), and balanced self-emission process and energy transfer process between DMAC-DPS and (tbt){sub 2}Ir(acac), contribute to high device performance.

Polymer and small molecule based hybrid light source

Science.gov (United States)

Choong, Vi-En; Choulis, Stelios; Krummacher, Benjamin Claus; Mathai, Mathew; So, Franky

2010-03-16

An organic electroluminescent device, includes: a substrate; a hole-injecting electrode (anode) coated over the substrate; a hole injection layer coated over the anode; a hole transporting layer coated over the hole injection layer; a polymer based light emitting layer, coated over the hole transporting layer; a small molecule based light emitting layer, thermally evaporated over the polymer based light emitting layer; and an electron-injecting electrode (cathode) deposited over the electroluminescent polymer layer.

Electroluminescence dependence of the simplified green light organic light emitting diodes on in situ thermal treatment

Energy Technology Data Exchange (ETDEWEB)

Mu, Haichuan, E-mail: hcmu@ecust.edu.cn [Department of Physics, School of Science, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China); Rao, Lu [Department of Physics, School of Science, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China); Li, Weiling; Wei, Bin [Key Laboratory of Advanced Display and System Applications, Ministry of Education, School of Mechanics Engineering and Automation, Shanghai University, 149 Yanchang Road, Shanghai 200072 (China); Wang, Keke; Xie, Haifen [Department of Physics, School of Science, East China University of Science and Technology, 130 Meilong Road, Shanghai 200237 (China)

2015-12-01

Highlights: • In-situ thermal treating the organic tri-layer (CBP/CBP:Ir(ppy){sub 3}/TPBi) of the green light PHOLED under various temperatures during the organic materials evaporation. • Investigating the effect of in situ thermal treatment on the electroluminescence (EL) performance of the green light PHOLED with tri-layer structures. • Provide an easy and practical way to improve the EL performance of the OLEDs without major modification of the organic materials and OLEDs structures required. - Abstract: Simplified multilayer green light phosphorescent organic light emitting diodes (PHOLED) with the structure of ITO/MoO{sub 3}(1 nm)/CBP(20 nm)/CBP:Ir(ppy){sub 3} (1 wt%) (15 nm)/TPBi(60 nm)/LiF(0.5 nm)/Al were fabricated via thermal evaporation and in situ thermal treatment (heating the OLED substrates to certain temperatures during the thermal evaporation of the organic materials) was performed. The effect of the in situ thermal treatment on the electroluminescence (EL) performance of the PHOLED was investigated. It was found that the OLED exhibited strong EL dependence on the thermal treatment temperatures, and their current efficiency was improved with the increasing temperature from room temperature (RT) to 69 °C and deteriorated with the further increasing temperature to 105 °C. At the brightness of 1000 cd/m{sup 2}, over 80% improvement of the current efficiency at the optimal thermal treatment temperature of 69 °C (64 cd/A) was demonstrated compared to that at RT (35 cd/A). Meanwhile, the tremendous influences of the in situ thermal treatment on the morphology of the multilayer CBP/CBP:Ir(ppy){sub 3}/TPBi were also observed. At the optimal thermal treatment temperature of 69 °C, the improvement of the EL performance could be ascribed to the enhancement of the electron and hole transporting in the CBP:Ir(ppy){sub 3} emitting layer, which suppressed the triplets self-quenching interactions and promoted the charge balance and excitons formation. The

New cyclometalated iridium(III) complex as a phosphorescent dopant in organic light emitting devices

Science.gov (United States)

Ivanov, P.; Tomova, R.; Petrova, P.; Stanimirov, S.; Petkov, I.

2014-05-01

A new cyclometalated iridium (III) bis[2-(4-chlorophenyl)benzothiazolato-N,C2]-acetylacetonate, (Cl-bt)2Ir(acac), was synthesized and identified by 1H NMR and elemental analysis. The application was studied of the new compound as a dopant in the hole transporting layer (HTL) of the following organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was 4,4'-bis(9H-carbazol-9-yl)biphenyl (CBP) or N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD), incorporated in a poly(N-vinylcarbazole) (PVK) matrix; EL was an electroluminescent layer of bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy) aluminum (BAlq); and ETL was an electron-transporting layer of bis[2-(2-benzothiazoly) phenolato]zinc(II) (Zn(btz)2). We established that the electroluminescence spectra of the OLEDs at different dopant concentrations were basically the sum of the greenish-blue emission of BAlq and the yellowish-green emission of the Ir complex. It was also found that increasing the dopant concentration resulted in an increase in the relative electroluminescent intensity of the Ir complex emission, while that of BAlq decreased, thus a fine tuning of the OLED color was observed.

Effects of the charge-transfer reorganization energy on the open-circuit voltage in small-molecular bilayer organic photovoltaic devices: comparison of the influence of deposition rates of the donor.

Science.gov (United States)

Lee, Chih-Chien; Su, Wei-Cheng; Chang, Wen-Chang

2016-05-14

The theoretical maximum of open-circuit voltage (VOC) of organic photovoltaic (OPV) devices has yet to be determined, and its origin remains debated. Here, we demonstrate that VOC of small-molecule OPV devices can be improved by controlling the deposition rate of a donor without changing the interfacial energy gap at the donor/acceptor interface. The measurement of external quantum efficiency and electroluminescence spectra facilitates the observation of the existence of charge transfer (CT) states. A simplified approach by reusing the reciprocity relationship for obtaining the properties of the CT states is proposed without introducing complex techniques. We compare experimental and fitting results and propose that reorganization energy is the primary factor in determining VOC instead of either the CT energy or electronic coupling term in bilayer OPV devices. Atomic force microscopy images indicate a weak molecular aggregation when a higher deposition rate is used. The results of temperature-dependent measurements suggest the importance of molecular stacking for the CT properties.

Degradation of Bilayer Organic Light-Emitting Diodes Studied by Impedance Spectroscopy.

Science.gov (United States)

Sato, Shuri; Takata, Masashi; Takada, Makoto; Naito, Hiroyoshi

2016-04-01

The degradation of bilayer organic light-emitting diodes (OLEDs) with a device structure of N,N'-di(1-naphthyl)-N,N'-diphenylbenzidine (α-NPD) (hole transport layer) and tris-(8-hydroxyquinolate)aluminum (Alq3) (emissive layer and electron transport layer) has been studied by impedance spectroscopy and device simulation. Two modulus peaks are found in the modulus spectra of the OLEDs below the electroluminescence threshold. After aging of the OLEDs, the intensity of electroluminescence is degraded and the modulus peak due to the Alq3 layer is shifted to lower frequency, indicating that the resistance of the Alq3 layer is increased. Device simulation reveals that the increase in the resistance of the Alq3 layer is due to the decrease in the electron mobility in the Alq3 layer.

STM-electroluminescence from clustered C3N4 nanodomains synthesized via green chemistry process.

Science.gov (United States)

Andrade, E P; Costa, B B A; Chaves, C R; de Paula, A M; Cury, L A; Malachias, A; Safar, G A M

2018-01-01

A Scanning Tunneling Microscopy/Spectroscopy (STM/STS) and synchrotron X-ray diffraction study on clustered C 3 N 4 nanoparticles (nanoflakes) is conducted on green-chemistry synthesized samples obtained from chitosan through high power sonication. Morphological aspects and the electronic characteristics are investigated. The observed bandgap of the nanoflakes reveals the presence of different phases in the material. Combining STM morphology, STS spectra and X-ray diffraction (XRD) results one finds that the most abundant phase is graphitic C 3 N 4 . A high density of defects is inferred from the XRD measurements. Additionally, STM-electroluminescence (STMEL) is detected in C 3 N 4 nanoflakes deposited on a gold substrate. The tunneling current creates photons that are three times more energetic than the tunneling electrons of the STM sample. We ponder about the two most probable models to explain the observed photon emission energy: either a nonlinear optical phenomenon or a localized state emission. Copyright © 2017 Elsevier B.V. All rights reserved.

Electroluminescence properties of Si MOS structures with incorporation of FeSi2 precipitates formed by iron implantation

International Nuclear Information System (INIS)

Chow, C.F.; Wong, S.P.; Gao, Y.; Ke, N.; Li, Q.; Cheung, W.Y.; Lourenco, M.A.; Homewood, K.P.

2005-01-01

Silicon MOS structures with FeSi 2 precipitates embedded in the MOS active region have been fabricated and the electroluminescence (EL) properties from these FeSi 2 -Si MOS structures were measured as a function of temperature from 80 K to 300 K. Clear EL signals were observed even at room temperature for samples prepared at appropriate processing conditions. The EL spectra consist of two peaks, one attributed to FeSi 2 and the other attributed to Si band edge emission. While the intensity of the FeSi 2 peak showed the usual thermal quenching behavior, the Si band edge emission showed the opposite trend with its intensity increased with increasing temperature. Details of the line shapes and their temperature dependence are analyzed and discussed

The characteristics of electroplex generated from the organic light emitting diodes.

Science.gov (United States)

Shin, Dong-Myung

2010-10-01

The color stability and purity from OLED is of current interest. Aggregation of dyes alters the device color after fabrication of the devices. The aggregates can be exciplex and electroplex, which is the excited complex that generated after electrically excited state under high electric field. Comparative study of emission spectra of exciplex and electroplex leads us to conclude that the new electroplex states causes the bathochromic shift of the electroluminescence spectrum from the devices with TPD/PBD layers. The photoluminescence maximum obtained from the TPD/PBD layers of the device was 420 nm, and the electroluminescence maximum obtained from the device became 480 nm. The bathochromic shift cannot be attained with photoluminescence study with highly concentrated TPD/PBD mixture. This clearly indicates that the 480 nm spectrum of the devices is not resulted from the exciplex formation with TPD and PBD. We observed the overshoot in EL spectrum from the OLEDs. The most intense overshoot was observed at 460 nm, which is due to the aggregate that are formed after the electric field has been removed from the devices.

Electroluminescence from ZnO/Si heterojunctions fabricated by PLD with bias voltage application

Science.gov (United States)

Seno, Yuuki; Konno, Daisuke; Komiyama, Takao; Chonan, Yasunori; Yamaguchi, Hiroyuki; Aoyama, Takashi

2014-02-01

Electroluminescence (EL) for ZnO films has been investigated by fabricating n-ZnO/p-Si heterojunctions and changing the VI/II (O/Zn) ratio of the films. In the photoluminescence (PL) spectra, both the near band edge (NBE) emission and the defect-related emission were observed, while in the EL spectra only defect-related emission was observed. The EL spectra were divided into three components: green (550 nm), yellow (618 nm) and red (700 nm) bands; and their intensities were compared. As the VI/II (O/Zn) ratio was increased, the red band emission intensity decreased and the green band emission intensity increased. This implies that the oxygen and the zinc vacancies are related to the red and the green band emissions, respectively. Electron transitions from the conduction band minimum (Ec) to the deep energy levels of these vacancies are suggested to cause the red and the green luminescences while the energy levels of the Zn interstitials are close to the Ec in the band gap and no NBE emission is observed.

Electroluminescence from ZnO/Si heterojunctions fabricated by PLD with bias voltage application

International Nuclear Information System (INIS)

Seno, Yuuki; Konno, Daisuke; Komiyama, Takao; Chonan, Yasunori; Yamaguchi, Hiroyuki; Aoyama, Takashi

2014-01-01

Electroluminescence (EL) for ZnO films has been investigated by fabricating n-ZnO/p-Si heterojunctions and changing the VI/II (O/Zn) ratio of the films. In the photoluminescence (PL) spectra, both the near band edge (NBE) emission and the defect-related emission were observed, while in the EL spectra only defect-related emission was observed. The EL spectra were divided into three components: green (550 nm), yellow (618 nm) and red (700 nm) bands; and their intensities were compared. As the VI/II (O/Zn) ratio was increased, the red band emission intensity decreased and the green band emission intensity increased. This implies that the oxygen and the zinc vacancies are related to the red and the green band emissions, respectively. Electron transitions from the conduction band minimum (Ec) to the deep energy levels of these vacancies are suggested to cause the red and the green luminescences while the energy levels of the Zn interstitials are close to the Ec in the band gap and no NBE emission is observed

Investigations on electroluminescent tapes and foils in relation to their applications in automotive

Science.gov (United States)

Plotog, Ioan

2015-02-01

The electroluminescent (EL) tapes or foils having barrier films for an additional level of protection against the toughest environments conditions, offer a large area of applications. The EL lights, due to their characteristics, began to be used not only in the entertainment industry, but also for automotive and aerospace applications. In the paper, the investigations regarding EL foils technical performances in relation to their applications as light sources in automotive ambient light were presented. The experiments were designed based on the results of EL foils electrical properties previous investigations done in laboratory conditions, taking into account the range of automotive ambient temperatures for sinusoidal alternative supply voltage. The measurements for different temperatures were done by keeping the EL foils into electronic controlled oven that ensures the dark enclosure offering conditions to use a lux-meter in order to measure and maintain under control light emission intensity. The experiments results define the EL foils characteristics as load in automotive ambient temperatures condition, assuring so the data for optimal design of a dedicated inverter.

Electroluminescence enhancement for near-ultraviolet light emitting diodes with graphene/AZO-based current spreading layers

DEFF Research Database (Denmark)

Lin, Li; Ou, Yiyu; Zhu, Xiaolong

LEDs) have attracted significant research interest due to their intensive applications in various areas where indium tin oxide (ITO) is one of the most widely employed transparent conductive materials for NUV LEDs. Compared to ITO, indium-free aluminum-doped zinc oxide (AZO) has similar electrical......Near-ultraviolet light emitting diodes with different aluminum-doped zinc oxide-based current spreading layers were fabricated and electroluminescence (EL) was compared. A 170% EL enhancement was achieved by using a graphene-based interlayer. GaN-based near-ultraviolet light emitting diodes (NUV...... with a new type of current spreading layer (CSL) which combines AZO and a single-layer graphene (SLG) as an effective transparent CSL [1]. In the present work, LEDs with solo AZO CSL in Fig.1(a) and SLG/Ni/AZO-based CSL in Fig.1(b) were both fabricated for EL comparison. Standard mesa fabrication including...

Optical characterization of voltage-accelerated degradation in CH3NH3PbI3 perovskite solar cells.

Science.gov (United States)

Handa, Taketo; Tex, David M; Shimazaki, Ai; Aharen, Tomoko; Wakamiya, Atsushi; Kanemitsu, Yoshihiko

2016-05-16

We investigate the performance degradation mechanism of CH3NH3PbI3 perovskite solar cells under bias voltage in air and nitrogen atmospheres using photoluminescence and electroluminescence techniques. When applying forward bias, the power conversion efficiency of the solar cells decreased significantly in air, but showed no degradation in nitrogen atmosphere. Time-resolved photoluminescence measurements on these devices revealed that the application of forward bias in air accelerates the generation of non-radiative recombination centers in the perovskite layer buried in the device. We found a negative correlation between the electroluminescence intensity and the injected current intensity in air. The irreversible change of the perovskite grain surface in air initiates the degradation of the perovskite solar cells.

Red polymer light-emitting devices based on an oxadiazole-functionalized europium(III) complex

International Nuclear Information System (INIS)

Liu, Yu; Wang, Yafei; Li, Chun; Huang, Ying; Dang, Dongfeng; Zhu, Meixiang; Zhu, Weiguo; Cao, Yong

2014-01-01

A novel tris(dibenzoylmethanato)[5-(2-(4-tert-butylbenzenyl)-5-benzenyl-1,3, 4-oxadiazole-4′)-1,10-phenanthroline]europium(III) [Eu(DBM) 3 (BuOXD-Phen)] containing an electron-transporting oxadiazole-functionalized phenanthroline ligand was synthesized and characterized. Its UV–vis absorption and photoluminescence (PL), as well as the electroluminescence (EL) in polymer light-emitting devices (PLEDs) were investigated. The double-layer PLEDs with a configuration of ITO/PEDOT:PSS (50 nm)/PVK (40 nm)/PFO:PBD (30%):Eu(DBM) 3 (BuOXD-Phen) (1–8 wt %) (80 nm)/Ba (4 nm)/Al (150 nm) were fabricated. Saturated red Eu 3+ ion emission, based on the 5 D 0 → 7 F 2 transition, is centered at a wavelength of 614 nm with a full width at half maximum (FWHM) of 10 nm. The highest external quantum efficiency (QE ext ) of 1.26% at current density of 1.65 mA cm −2 , with a maximum brightness of 568 cd m −2 at 137.8 mA cm −2 was achieved from the device at 1 wt % dopant concentration. - Highlights: • An oxadiazole-functionalized europium(III) complex of Eu(DBM) 3 (BuOXD-Phen) was presented. • The optophysical properties of Eu(DBM) 3 (BuOXD-Phen) were investigated. • Saturated red emission was observed in the PLEDs. • An external quantum efficiency of 1.26% was obtained in these devices

Reinventing a p-type doping process for stable ZnO light emitting devices

Science.gov (United States)

Xie, Xiuhua; Li, Binghui; Zhang, Zhenzhong; Shen, Dezhen

2018-06-01

A tough challenge for zinc oxide (ZnO) as the ultraviolet optoelectronics materials is realizing the stable and reliable p-type conductivity. Self-compensation, coming from native donor-type point defects, is a big obstacle. In this work, we introduce a dynamic N doping process with molecular beam epitaxy, which is accomplished by a Zn, N-shutter periodic switch (a certain time shift between them for independent optimization of surface conditions). During the epitaxy, N adatoms are incorporated under the condition of (2  ×  2)  +  Zn vacancies reconstruction on a Zn-polar surface, at which oxygen vacancies (V O), the dominating compensating donors, are suppressed. With the p-ZnO with sufficient holes surviving, N concentration ~1  ×  1019 cm‑3, is employed in a p-i-n light emitting devices. Significant ultraviolet emission of electroluminescence spectra without broad green band (related to V O) at room-temperature are demonstrated. The devices work incessantly without intentional cooling for over 300 h at a luminous intensity reduction of one order of magnitude under the driving of a 10 mA continuous current, which are the demonstration for p-ZnO stability and reliability.

Surface modification and characterization of indium-tin oxide for organic light-emitting devices.

Science.gov (United States)

Zhong, Z Y; Jiang, Y D

2006-10-15

In this work, we used different treatment methods (ultrasonic degreasing, hydrochloric acid treatment, and oxygen plasma) to modify the surfaces of indium-tin oxide (ITO) substrates for organic light-emitting devices. The surface properties of treated ITO substrates were studied by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), sheet resistance, contact angle, and surface energy measurements. Experimental results show that the ITO surface properties are closely related to the treatment methods, and the oxygen plasma is more efficient than the other treatments since it brings about smoother surfaces, lower sheet resistance, higher work function, and higher surface energy and polarity of the ITO substrate. Moreover, polymer light-emitting electrochemical cells (PLECs) with differently treated ITO substrates as device electrodes were fabricated and characterized. It is found that surface treatments of ITO substrates have a certain degree of influence upon the injection current, brightness, and efficiency, but hardly upon the turn-on voltages of current injection and light emission, which are in agreement with the measured optical energy gap of the electroluminescent polymer. The oxygen plasma treatment on the ITO substrate yields the best performance of PLECs, due to the improvement of interface formation and electrical contact of the ITO substrate with the polymer blend in the PLECs.

Device characterization for design optimization of 4 junction inverted metamorphic concentrator solar cells

Energy Technology Data Exchange (ETDEWEB)

Geisz, John F.; France, Ryan M.; Steiner, Myles A.; Friedman, Daniel J. [National Renewable Energy Laboratory, Golden, CO 80401 (United States); García, Iván [National Renewable Energy Laboratory, Golden, CO 80401 USA and Instituto de Energía Solar, Universidad Politécnica de Madrid, Avda Complutense s/n, 28040 Madrid (Spain)

2014-09-26

Quantitative electroluminescence (EL) and luminescent coupling (LC) analysis, along with more conventional characterization techniques, are combined to completely characterize the subcell JV curves within a fourjunction (4J) inverted metamorphic solar cell (IMM). The 4J performance under arbitrary spectral conditions can be predicted from these subcell JV curves. The internal radiative efficiency (IRE) of each junction has been determined as a function of current density from the external radiative efficiency using optical modeling, but this required the accurate determination of the individual junction current densities during the EL measurement as affected by LC. These measurement and analysis techniques can be applied to any multijunction solar cell. The 4J IMM solar cell used to illustrate these techniques showed excellent junction quality as exhibited by high IRE and a one-sun AM1.5D efficiency of 36.3%. This device operates up to 1000 suns without limitations due to any of the three tunnel junctions.

Study of structural, morphological, optical and electroluminescent properties of undoped ZnO nanorods grown by a simple chemical precipitation

Directory of Open Access Journals (Sweden)

Singh A.

2015-12-01

Full Text Available In this work, zinc oxide (ZnO nanorods were obtained by a simple chemical precipitation method in the presence of capping agent: polyvinyl pyrrolidone (PVP at room temperature. X-ray diffraction (XRD result indicates that the synthesized undoped ZnO nanorods have hexagonal wurtzite structure without any impurities. It has been observed that the growth direction of the prepared ZnO nanorods is [1 0 1]. XRD analysis revealed that the nanorods have the crystallite size of 49 nm. Crystallite size is calculated by Debye-Scherrer formula and lattice strain is calculated by Williomson-Hall equation. Cell volume, Lorentz factor, Lorentz polarization factor, bond length, texture coefficient, lattice constants and dislocation density have also been studied. We also compared the interplanar spacings and relative peak intensities with their standard values at different angles. The scanning electron microscope (SEM images confirmed the size and shape of these nanorods. It has been found that the diameter of the nanorods ranges from 1.52 μm to 1.61 μm and the length is about 4.89 μm. It has also been observed that at room temperature ultraviolet visible (UV-Vis absorption band is around 355 nm (blue shifted as compared to the bulk. The average particle size has also been calculated by mathematical model of effective mass approximation equation, using UV-Vis absorption peak. Finally, the bandgap has been calculated using UV-absorption peak. Electroluminescence (EL studies show that emission of light is possible at very small threshold voltage and it increases rapidly with increasing applied voltage. It is seen that smaller ZnO nanoparticles give higher electroluminescence brightness starting at lower threshold voltage. The brightness is also affected by increasing the frequency of AC signal.

Synthesis, Crystal Structure, Theoretical Study, The

Indian Academy of Sciences (India)

in light-emitting devices, electroluminescence devices, and probes of biological systems.9 14 The copper(I) ion has d10 electronic configuration and can adopt diverse ... The SMART and SAINT program packages were used for data collection and inte- gration, respectively. The collected data were also corrected.

Single-Layer Halide Perovskite Light-Emitting Diodes with Sub-Band Gap Turn-On Voltage and High Brightness.

Science.gov (United States)

Li, Junqiang; Shan, Xin; Bade, Sri Ganesh R; Geske, Thomas; Jiang, Qinglong; Yang, Xin; Yu, Zhibin

2016-10-03

Charge-carrier injection into an emissive semiconductor thin film can result in electroluminescence and is generally achieved by using a multilayer device structure, which requires an electron-injection layer (EIL) between the cathode and the emissive layer and a hole-injection layer (HIL) between the anode and the emissive layer. The recent advancement of halide perovskite semiconductors opens up a new path to electroluminescent devices with a greatly simplified device structure. We report cesium lead tribromide light-emitting diodes (LEDs) without the aid of an EIL or HIL. These so-called single-layer LEDs have exhibited a sub-band gap turn-on voltage. The devices obtained a brightness of 591 197 cd m -2 at 4.8 V, with an external quantum efficiency of 5.7% and a power efficiency of 14.1 lm W -1 . Such an advancement demonstrates that very high efficiency of electron and hole injection can be obtained in perovskite LEDs even without using an EIL or HIL.

Temperature and current dependent electroluminescence measurements on colour-coded multiple quantum well light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Bergbauer, Werner [OSRAM Opto Semiconductors GmbH, Regensburg (Germany); FH Deggendorf (Germany); Laubsch, Ansgar; Peter, Matthias; Mayer, Tobias; Bader, Stefan; Oberschmid, Raimund; Hahn, Berthold [OSRAM Opto Semiconductors GmbH, Regensburg (Germany); Benstetter, Guenther [FH Deggendorf (Germany)

2008-07-01

As the efficiency and the luminous flux have been increased enormously in the last few years, today Light Emitting Diodes (LEDs) are even pushed to applications like general lighting and Home Cinema Projection. Still, InGaN/GaN heterostructure based LEDs suffer from loss-mechanisms like non-radiative defect and Auger recombination, carrier leakage and piezo-field induced carrier separation. To optimize the high current efficiency we evaluated the benefit of Multiple Quantum Well (MQW) compared to Single Quantum Well (SQW) LEDs. Temperature dependent electroluminescence of colour-coded structures with different Indium content in certain Quantum Wells was measured. The experiments demonstrated a strong temperature and current dependence of the MQW operation. The comparison between different LED structures showed effectively the increased LED performance of those structures which operate with a well adjusted MQW active area. Due to the enhanced carrier distribution in the high current range, these LEDs show a higher light output and additionally a reduced wavelength shift.

Temperature and current dependent electroluminescence measurements on colour-coded multiple quantum well light emitting diodes

International Nuclear Information System (INIS)

Bergbauer, Werner; Laubsch, Ansgar; Peter, Matthias; Mayer, Tobias; Bader, Stefan; Oberschmid, Raimund; Hahn, Berthold; Benstetter, Guenther

2008-01-01

As the efficiency and the luminous flux have been increased enormously in the last few years, today Light Emitting Diodes (LEDs) are even pushed to applications like general lighting and Home Cinema Projection. Still, InGaN/GaN heterostructure based LEDs suffer from loss-mechanisms like non-radiative defect and Auger recombination, carrier leakage and piezo-field induced carrier separation. To optimize the high current efficiency we evaluated the benefit of Multiple Quantum Well (MQW) compared to Single Quantum Well (SQW) LEDs. Temperature dependent electroluminescence of colour-coded structures with different Indium content in certain Quantum Wells was measured. The experiments demonstrated a strong temperature and current dependence of the MQW operation. The comparison between different LED structures showed effectively the increased LED performance of those structures which operate with a well adjusted MQW active area. Due to the enhanced carrier distribution in the high current range, these LEDs show a higher light output and additionally a reduced wavelength shift

Cultural Resources Investigations at Redstone Arsenal, Madison County, Alabama. Volume II.

Science.gov (United States)

1980-01-01

was an infant or child . Parts of broken pottery vessels were found with two of the burials. I As mentioned above, ceramics were relatively infrequent...ai-j- IL is also due to a certain amiount of I tI ’rt ie 1(a ao -- tilit- iV! t-ri i process does not porn i t an extant I ii tfel to !, -,I) Ip it

Three-peak standard white organic light-emitting devices for solid-state lighting

Science.gov (United States)

Guo, Kunping; Wei, Bin

2014-12-01

Standard white organic light-emitting device (OLED) lighting provides a warm and comfortable atmosphere and shows mild effect on melatonin suppression. A high-efficiency red OLED employing phosphorescent dopant has been investigated. The device generates saturated red emission with Commission Internationale de l'Eclairage (CIE) coordinates of (0.66, 0.34), characterized by a low driving voltage of 3.5 V and high external quantum efficiency of 20.1% at 130 cd m-2. In addition, we have demonstrated a two-peak cold white OLED by combining with a pure blue emitter with the electroluminescent emission of 464 nm, 6, 12-bis{[N-(3,4-dimethylpheyl)-N-(2,4,5-trimethylphenyl)]} chrysene (BmPAC). It was found that the man-made lighting device capable of yielding a relatively stable color emission within the luminance range of 1000-5000 cd m-2. And the chromaticity coordinates, varying from (0.25, 0.21) to (0.23, 0.21). Furthermore, an ultrathin layer of green-light-emitting tris (2-phenylpyridinato)iridium(Ⅲ) Ir(ppy)3 in the host material was introduced to the emissive region for compensating light. By appropriately controlling the layer thickness, the white light OLED achieved good performance of 1280 cd m-2 at 5.0 V and 5150 cd m-2 at 7.0 V, respectively. The CIE coordinates of the emitted light are quite stable at current densities from 759 cd m-2 to 5150 cd m-2, ranging from (0.34, 0.37) to (0.33, 0.33).

Origin of the Electroluminescence from Annealed-ZnO/GaN Heterojunction Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Kai-Chiang Hsu

2015-11-01

Full Text Available This paper addressed the effect of post-annealed treatment on the electroluminescence (EL of an n-ZnO/p-GaN heterojunction light-emitting diode (LED. The bluish light emitted from the 450 °C-annealed LED became reddish as the LED annealed at a temperature of 800 °C under vacuum atmosphere. The origins of the light emission for these LEDs annealed at various temperatures were studied using measurements of electrical property, photoluminescence, and Auger electron spectroscopy (AES depth profiles. A blue-violet emission located at 430 nm was associated with intrinsic transitions between the bandgap of n-ZnO and p-GaN, the green-yellow emission at 550 nm mainly originating from the deep-level transitions of native defects in the n-ZnO and p-GaN surfaces, and the red emission at 610 nm emerging from the Ga-O interlayer due to interdiffusion at the n-ZnO/p-GaN interface. The above-mentioned emissions also supported the EL spectra of LEDs annealed at 700 °C under air, nitrogen, and oxygen atmospheres, respectively.

White electroluminescence from ZnO nanorods/p-GaN heterojunction light-emitting diodes under reverse bias

International Nuclear Information System (INIS)

Zhang, Lichun; Li, Qingshan; Qu, Chong; Zhang, Zhongjun; Huang, Ruizhi; Zhao, Fengzhou

2013-01-01

Heterojunction light-emitting diodes (LEDs) based on arrays of ZnO nanorods were fabricated on p-GaN films by the hydrothermal method. Without any phosphors, white-light electroluminescence (EL) from ZnO nanorods/p-GaN heterojunction LEDs operated at reverse breakdown bias was observed. The EL spectra are composed of an ultraviolet (UV) emission centered at 382 nm, a blue light located at 431 nm and a broadband yellow–green light at around 547 nm, which originated from band-edge emission in ZnO, the Mg acceptor levels in p-GaN and the deep-level states near the ZnO/GaN interface, respectively. The chromaticity coordinates of EL spectrum are very close to the (0.333, 0.333) of standard white light. The origin of these emissions has been discussed and the tunneling effect in the interface is probably the mechanism to explain EL emission. (paper)

Luminance and image quality analysis of an organic electroluminescent panel with a patterned microlens array attachment

International Nuclear Information System (INIS)

Lin, Hoang Yan; Chen, Kuan-Yu; Ho, Yu-Hsuan; Fang, Jheng-Hao; Hsu, Sheng-Chih; Lee, Jiun-Haw; Lin, Jia-Rong; Wei, Mao-Kuo

2010-01-01

Luminance and image quality observed from the normal direction of a commercial 2.0 inch panel based on organic electroluminescence (OEL) technology attached to regular and patterned microlens array films (MAFs) were studied and analyzed. When applying the regularly arranged MAF on the panel, a luminance enhancement of 23% was observed, accompanied by a reduction of the image quality index as low as 74%. By removing the microlenses on the emitting areas, the patterned MAF enhances the luminance efficiency of the OEL by 52% keeping the image quality index of the display as high as 94%, due to the effective light extraction in the glass substrate being less than the critical angle. 3D simulation based on a ray-tracing model was also established to investigate the spatial distribution of light rays radiated from an OEL pixel with different microstructures which showed consistent results with the experimental results

Electroluminescence and electrical degradation of insulating polymers at electrode interfaces under divergent fields

Science.gov (United States)

Zhang, Shuai; Li, Qi; Hu, Jun; Zhang, Bo; He, Jinliang

2018-04-01

Electrical degradation of insulating polymers at electrode interfaces is an essential factor in determining long-term reliability. A critical challenge is that the exact mechanism of degradation is not fully understood, either experimentally or theoretically, due to the inherent complex processes. Consequently, in this study, we investigate electroluminescence (EL) at the interface of an electrode and insulator, and determine the relationship between EL and electrical degradation. Using a tip-plate electrode structure, the unique features of EL under a highly divergent field are investigated. The voltage type (alternating or direct current), the polymer matrix, and the time of pressing are also investigated separately. A study of EL from insulators under a divergent field is provided, and the relationship between EL spectra and degradation is discussed. It is shown that EL spectra under a divergent field have unique characteristics compared with EL spectra from polymer films under a uniform field and the most obvious one is the UV emission. The results obtained in the current investigation bring us a step closer to understanding the process of electrical degradation and provide a potential way to diagnose insulator defects.

Bluish-white-light-emitting diodes based on two-dimensional lead halide perovskite (C6H5C2H4NH3)2PbCl2Br2

Science.gov (United States)

Cai, Peiqing; Wang, Xiangfu; Seo, Hyo Jin; Yan, Xiaohong

2018-04-01

Bluish-white-light-emitting diodes (BWLEDs) are designed based on the two-dimensional mixed halide perovskite (C6H5C2H4NH3)2PbCl2Br2 at room temperature. Bluish-white electroluminescence devices were fabricated by a spin-coating method. The BWLEDs can be turned on at 4.9 V and depict a maximum luminance of ˜70 cd/m2 at 7 V. Low and room temperature photoluminescence spectra show the coexistence of free exciton and self-trapped exciton luminescence in a deformable lattice. The strategy of achieving white electroluminescence (EL) from mixed halide perovskite reported here can be applied to other two-dimensional perovskites to increase the optoelectronic efficiency of the device in the future.

New copolymers with thieno[3,2-b]thiophene or dithieno[3,2-b:2',3'-d]thiophene units possessing electron-withdrawing 4-cyanophenyl groups: synthesis and photophysical, electrochemical, and electroluminescent properties

Czech Academy of Sciences Publication Activity Database

Výprachtický, Drahomír; Demirtas, I.; Dzhabarov, Vagif; Pokorná, Veronika; Ertas, E.; Ozturk, T.; Cimrová, Věra

2017-01-01

Roč. 55, č. 16 (2017), s. 2629-2638 ISSN 0887-624X R&D Projects: GA ČR(CZ) GA13-26542S Institutional support: RVO:61389013 Keywords : conjugated polymers * electrochemistry * electroluminescence Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 2.952, year: 2016

InGaN pn-junctions grown by PA-MBE: Material characterization and fabrication of nanocolumn electroluminescent devices

Science.gov (United States)

Gherasoiu, I.; Yu, K. M.; Reichertz, L.; Walukiewicz, W.

2015-09-01

PN junctions are basic building blocks of many electronic devices and their performance depends on the structural properties of the component layers and on the type and the amount of the doping impurities incorporated. Magnesium is the common p-type dopant for nitride semiconductors while silicon and more recently germanium are the n-dopants of choice. In this paper, therefore we analyze the quantitative limits for Mg and Ge incorporation on GaN and InGaN with high In content. We also discuss the challenges posed by the growth and characterization of InGaN pn-junctions and we discuss the properties of large area, long wavelength nanocolumn LEDs grown on silicon (1 1 1) by PA-MBE.

Shell model for REO{sub x} nanoclusters in amorphous SiO{sub 2}: charge trapping and electroluminescence quenching

Energy Technology Data Exchange (ETDEWEB)

Tiagulskyi, S.; Nazarov, A.; Tyagulskii, I.; Lysenko, V. [Lashkaryov Institute of Semiconductor Physics, National Academy of Sciences of Ukraine, Prospekt Nauki 41, 03028 Kiev (Ukraine); Rebohle, L.; Lehmann, J.; Skorupa, W. [Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden Rossendorf e.V., POB 510119, 01314 Dresden (Germany)

2012-06-15

In this work charge trapping and electroluminescence (EL) quenching in rare-earth (RE) implanted SiO{sub 2} on Si as a function of injected charge into the dielectric were studied. The blocking of the luminescent REO{sub X} nanoclusters from the hot exciting electrons by negative charge trapping in a defect region (shell) located in the vicinity of the REO{sub X} nanocluster/SiO{sub 2} interface is considered as the main mechanism of EL quenching for small size (up to 10 nm) REO{sub X} nanoclusters. It is suggested that the increase of the nanoclusters size results in disordering of the SiO{sub 2} matrix but in a decrease of local blocking for excitation of the luminescent centers. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Direct band gap electroluminescence from bulk germanium at room temperature using an asymmetric fin type metal/germanium/metal structure

Energy Technology Data Exchange (ETDEWEB)

Wang, Dong, E-mail: wang.dong.539@m.kyushu-u.ac.jp; Maekura, Takayuki; Kamezawa, Sho [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Yamamoto, Keisuke; Nakashima, Hiroshi [Art, Science and Technology Center for Cooperative Research, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan)

2015-02-16

We demonstrated direct band gap (DBG) electroluminescence (EL) at room temperature from n-type bulk germanium (Ge) using a fin type asymmetric lateral metal/Ge/metal structure with TiN/Ge and HfGe/Ge contacts, which was fabricated using a low temperature (<400 °C) process. Small electron and hole barrier heights were obtained for TiN/Ge and HfGe/Ge contacts, respectively. DBG EL spectrum peaked at 1.55 μm was clearly observed even at a small current density of 2.2 μA/μm. Superlinear increase in EL intensity was also observed with increasing current density, due to superlinear increase in population of elections in direct conduction band. The efficiency of hole injection was also clarified.

Efficient single light-emitting layer pure blue phosphorescent organic light-emitting devices with wide gap host and matched interlayer

Energy Technology Data Exchange (ETDEWEB)

Jiang, Yunlong; Zhou, Liang, E-mail: zhoul@ciac.ac.cn; Cui, Rongzhen; Li, Yanan; Zhao, Xuesen; Zhang, Hongjie, E-mail: hongjie@ciac.ac.cn

2015-12-15

In this work, we report the highly efficient pure blue electroluminescent (EL) device based on bis[(3,5-difluoro-4-cyanophenyl)pyridine]picolinate iridium(III) (FCNIrpic) doped 9-(4-tert-Butylphenyl)-3,6-bis(triphenylsilyl)-9H-carbazole (CzSi) film. The matched energy levels of FCNIrpic and CzSi are helpful in facilitating the trapping of carriers, while the high triplet energy of CzSi can well avoid the undesired reverse energy transfer. More importantly, the injection of holes was further accelerated by inserting 5 nm 4,4′,4″-Tri(9-carbazoyl)triphenylamine (TcTa) film between hole transport layer and lighting-emitting layer (EML) as interlayer. Consequently, EL performances were significantly enhanced attributed to wider recombination zone and better balance of holes and electrons. Interestingly, single-EML device displayed higher performances than those of double-EMLs device. Finally, pure blue EL device with the structure of ITO/MoO{sub 3} (3 nm)/TAPC (40 nm)/TcTa (5 nm)/FCNIrpic (20%): CzSi (30 nm)/TmPyPB (40 nm)/LiF (1 nm)/Al (100 nm) realized the maximum brightness, current efficiency, power efficiency and external quantum efficiency up to 12,505 cd/m{sup 2}, 36.20 cd/A, 28.42 lm/W and 16.9%, respectively. Even at the high brightness of 1000 cd/m{sup 2}, current efficiency and external quantum efficiency up to 17.40 cd/A and 8.1%, respectively, can be retained by the same device.

Highly efficient and concentration-insensitive organic light-emitting devices based on self-quenching-resistant orange–red iridium complex

Energy Technology Data Exchange (ETDEWEB)

Qi, Yige; Wang, Xu [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Li, Ming [College of Chemistry, Sichuan University, Chengdu 610064 (China); Lu, Zhiyun, E-mail: luzhiyun@scu.edu.cn [College of Chemistry, Sichuan University, Chengdu 610064 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2014-11-15

Orange–red phosphorescent organic light-emitting devices (PHOLEDs) with high efficiency and concentration insensitivity based on a novel iridium complex, bis[2-(biphenyl-4-yl)benzothiazole-N,C{sup 2}′]iridium(III) (acetylacetonate) [(4Phbt){sub 2}Ir(acac)], were fabricated. With the heavily doped emissive layer (EML) of 4,4′-N,N′-dicarbazolylbiphenyl (CBP): (4Phbt){sub 2}Ir(acac) in a wide and easily controlled dopant concentration range from 12 wt% to 24 wt%, a maximum power efficiency of 29 lm/W and an external quantum efficiency of >16% of the PHOLEDs were obtained, implying the insensitivity of electroluminescence (EL) properties to doping concentration. Meanwhile, a maximum power efficiency of 5.0 lm/W was achieved from a non-doped device with neat (4Phbt){sub 2}Ir(acac) as the EML, indicating a superior property of self-quenching resistance. The mechanism of direct exciton formation, in which exciton-formation regions are distributed throughout the EML, is responsible for the significant alleviation of triplet–triplet annihilation and superior EL performance. - Highlights: • Highly efficient and concentration-insensitive PHOLEDs were obtained. • The high efficiency of non-doped PHOLEDs indicated a quenching-resistant property. • The independence of EL spectra on doping concentration was observed. • The heavily doped devices were dominated by mechanism of direct exciton formation.

Enhancement of efficiencies for tandem green phosphorescent organic light-emitting devices with a p-type charge generation layer

Energy Technology Data Exchange (ETDEWEB)

Yoo, Byung Soo; Jeon, Young Pyo; Lee, Dae Uk; Kim, Tae Whan, E-mail: twk@hanayng.ac.kr

2014-10-15

The operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the organic light-emitting device with a molybdenum trioxide layer. The maximum brightness of the tandem green phosphorescent organic light-emitting device at 21.9 V was 26,540 cd/m{sup 2}. The dominant peak of the electroluminescence spectra for the devices was related to the fac-tris(2-phenylpyridine) iridium emission. - Highlights: • Tandem OLEDs with CGL were fabricated to enhance their efficiency. • The operating voltage of the tandem OLED with a HAT-CN layer was improved by 3%. • The efficiency and brightness of the tandem OLED were 13.9 cd/A and 26,540 cd/m{sup 2}. • Efficiency of the OLED with a HAT-CN layer was lower than that with a MoO{sub 3} layer. - Abstract: Tandem green phosphorescent organic light-emitting devices with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile or a molybdenum trioxide charge generation layer were fabricated to enhance their efficiency. Current density–voltage curves showed that the operating voltage of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was improved by 3% over that of the corresponding organic light-emitting device with a molybdenum trioxide layer. The efficiency and the brightness of the tandem green phosphorescent organic light-emitting device were 13.9 cd/A and 26,540 cd/m{sup 2}, respectively. The current efficiency of the tandem green phosphorescent organic light-emitting device with a 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer was lower by 1.1 times compared to that of the corresponding organic light-emitting device with molybdenum trioxide layer due to the decreased charge generation and transport in the 1,4,5,8,9,11-hexaazatriphenylene-hexacarbonitrile layer resulting from triplet–triplet exciton annihilation.

All-Quantum-Dot Infrared Light-Emitting Diodes

KAUST Repository

Yang, Zhenyu; Voznyy, Oleksandr; Liu, Mengxia; Yuan, Mingjian; Ip, Alexander H.; Ahmed, Osman S.; Levina, Larissa; Kinge, Sachin; Hoogland, Sjoerd; Sargent, Edward H.

2015-01-01

© 2015 American Chemical Society. Colloidal quantum dots (CQDs) are promising candidates for infrared electroluminescent devices. To date, CQD-based light-emitting diodes (LEDs) have employed a CQD emission layer sandwiched between carrier transport

Effect of gold nanorods and nanocubes on electroluminescent performances in organic light-emitting diodes and its working mechanism

Directory of Open Access Journals (Sweden)

Ying Xu

2015-06-01

Full Text Available In this manuscript we investigated the influence of Au nanoparticles on electrical and electroluminescent (EL performances in organic light-emitting diodes (OLEDs via doping as-synthesized Au nanorods (NRs or nanocubes (NCs into hole transport layer (HTL. Through accurately controlling the distance between the Au NRs and the emitting layer, altering the guest emitter’s lifetime, and replacing Au NRs with Au NCs to satisfy a better spectrum overlap with the emission guest, we got a conclusion that doping Au NRs or NCs into HTL has no significant influence on the device’s electrical and EL performances, although we observed an increase in the spontaneous emission rate in a fluorescent material by the exciton-surface plasmon-coupling. Our results suggest that a further research on emission mechanism in surface plasmon-enhanced OLEDs is still in process.

A review on organic spintronic materials and devices: II. Magnetoresistance in organic spin valves and spin organic light emitting diodes

Directory of Open Access Journals (Sweden)

Rugang Geng

2016-09-01

Full Text Available In the preceding review paper, Paper I [Journal of Science: Advanced Materials and Devices 1 (2016 128–140], we showed the major experimental and theoretical studies on the first organic spintronic subject, namely organic magnetoresistance (OMAR in organic light emitting diodes (OLEDs. The topic has recently been of renewed interest as a result of a demonstration of the magneto-conductance (MC that exceeds 1000% at room temperature using a certain type of organic compounds and device operating condition. In this report, we will review two additional organic spintronic devices, namely organic spin valves (OSVs where only spin polarized holes exist to cause magnetoresistance (MR, and spin organic light emitting diodes (spin-OLEDs where both spin polarized holes and electrons are injected into the organic emissive layer to form a magneto-electroluminescence (MEL hysteretic loop. First, we outline the major advances in OSV studies for understanding the underlying physics of the spin transport mechanism in organic semiconductors (OSCs and the spin injection/detection at the organic/ferromagnet interface (spinterface. We also highlight some of outstanding challenges in this promising research field. Second, the first successful demonstration of spin-OLEDs is reviewed. We also discuss challenges to achieve the high performance devices. Finally, we suggest an outlook on the future of organic spintronics by using organic single crystals and aligned polymers for the spin transport layer, and a self-assembled monolayer to achieve more controllability for the spinterface.

Green-Yellow Electroluminescence from a host-dopant blended system as the active layer in a bilayer polymer light emitting diode: Poly(n-vinyl carbazole) as the host and a new soluble thiophene based copolymer [poly(2,2‧-BT)-co-(3-DDT)] as the dopant

Science.gov (United States)

Shahalizad, Afshin; Ahmadi-Kandjani, Sohrab; Movla, Hossein; Omidi, Hafez; Massoumi, Bakhshali; Zakerhamidi, Mohammad Sadegh; Entezami, Ali Akbar

2014-11-01

A new type of bilayer Polymer Light Emitting Diode (PLED) which emits green-yellow light is reported. In this PLED, a novel thiophene-based copolymer [poly(2,2‧-BT)-co-(3-DDT)] with an excellent electron transporting property has been doped in hole transporting and electron blocking poly(n-vinylcarbazole) (PVK). Formation of type-II heterojunctions among nm-size features in PVK:poly(2,2‧-BT)-co-(3-DDT) blended system makes exciplex and electroplex emissions would be dominant in the Electroluminescence (EL) spectrum of the device. These cross recombinations between electrons in the LUMO of poly(2,2‧-BT)-co-(3-DDT) and holes in the HOMO of PVK is a reason for the low driving voltage of the PLED because there is no need for the charge carriers to hop or tunnel to the adjacent polymer. Morphological investigations demonstrate that the mixing degree between the components is high, favoring formation of exciplexes and electroplexes at the interface of the components.

Ultraviolet electroluminescence from n-ZnO/p-NiO heterojunction light-emitting diode

International Nuclear Information System (INIS)

Deng, R.; Yao, B.; Li, Y.F.; Xu, Y.; Li, J.C.; Li, B.H.; Zhang, Z.Z.; Zhang, L.G.; Zhao, H.F.; Shen, D.Z.

2013-01-01

The n-ZnO/p-NiO heterojunction was prepared by depositing a p-type NiO film on a c-plane sapphire by rf magnetron sputtering and then growing a n-type ZnO film on the NiO film by plasma-assisted molecular beam epitaxy. The heterojunction shows a diode-like rectification characteristic with a turn-on voltage of ∼3.6 V and emits UV light upon putting a forward bias. The intensity of the UV emission increases as injection current increases from 0.5 to 3.5 mA, but the wavelength of the UV emission decreases from 404 to 387 nm. It is demonstrated that the UV emission comes from near band-edge radiative recombination of electron and hole in the ZnO layer. The mechanism of the UV electroluminescence is discussed in the present work. - Highlights: ► The n-ZnO/p-NiO heterojunction was prepared by rf magnetron sputtering. ► The heterojunction shows a diode-like rectification characteristic with a turn-on voltage of ∼3.6 V. ► The heterojunction realizes UV EL emission with wavelength of 387 nm at the injection current of 3.5 mA.

An Active Plasmonic to Explore on-Chip Sensing Applications

Directory of Open Access Journals (Sweden)

Nan-Fu Chiu

2016-06-01

Full Text Available We report the influence of top emission and transparent organic electroluminescence (OEL devices on the color tunability, viewing angle and enhancement light efficiency by surface plasmon grating coupled emission (SPGCE, the effects of coupled active SPPs on the metal nano-grating with organic material interface by cross-coupled into far-field space. Owing to the narrow band emission from the SPGCE, one can observe clear color changes at a certain viewing angle with different permittivities. The experimental and theoretical results showed that OEL-SPGCE at different pitch can match a linear shifting of momentum (DK of about 4.8 mm-1 per 100 nm pitch size. The color changes from -1.1 degree (water, -.07 degree (glucose 10 %, -2.5 degree (glucose 20 %, to 6 degree (glucose 40 % with the increasing permittivities. The OEL-SPGCE biosensor is proposed for the development of novel devices, which is expected to improve the capability of electroluminescent bio-plasmonic resonance measurement devices in the future.

Electroluminescence in quantum well heterostructures p-Al{sub x}Ga{sub 1-x}As/GaAs{sub 1-y}P{sub y}/n-Al{sub x}Ga{sub 1-x}As under uniaxial stress

Energy Technology Data Exchange (ETDEWEB)

Berman, Irina V. [Physics Department, San Jose State University, CA (United States); Bogdanov, Evgeniy V.; Minina, Natalia Ya.; Shirokov, Stanislav S.; Yunovich, Alexander E. [Physics Department, Lomonosov Moscow State University (Russian Federation); Kissel, Heiko [R and D Department, DILAS Diodenlaser GmbH, (Germany)

2009-03-15

We present new results on the influence of uniaxial stress up to P=4 kbar on the electroluminescence spectra and current-voltage characteristics of p-Al{sub x}Ga{sub 1-x}As/GaAs{sub 1-y}P{sub y}/n-Al{sub x}Ga{sub 1-x}As double heterostructures usually used in TM emitting 808 nm high-power diode lasers. With increasing stress, the emission spectra demonstrate a blue shift of up to 25 meV at a pressure of P=4 kbar, while the electroluminescence intensity increases under compression. The different behavior of the current-voltage characteristics under uniaxial stress along[110] and[1 anti 10] directions is mainly determined by the arising piezoelectric field. The results are also discussed in terms of changes in the band structure under uniaxial compression. The construction of the cryostat for optical measurements under uniaxial stress at liquid nitrogen temperature is described in the paper. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The colour-tuning effect of 2,9-dimethyl-4,7-diphenyl-1, 10-phenanthroline in blue-red organic light-emitting devices

International Nuclear Information System (INIS)

Lin Jian; Xia, Yi-Jie; Tang Chao; Yin Kun; Zhong Gaoyu; Ni Gang; Peng Bo; Hou Xiaoyuan; Gan Fuxi; Huang Wei

2007-01-01

This paper reports the fabrication and measurement of organic light-emitting devices comprised of indium-tin-oxide (ITO)/4,4',4-prime-tris(N-carbazolyl)-triphenylamine (TCTA, 8 nm)/2-pyrenyl-9-phenyl-9-pyrenylfluorene(2P9PPF, 30 nm)/ bathocuproine (BCP, with different thickness)/Alq 3 : DCJTB (DCJTB = 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7- tetramethyljulolidyl-9-enyl)-4H-pyran, Alq 3 = tris(8-hydroxyquinolino) aluminium(III), 2% in mass ratio, 30 nm)/Mg : Ag(250 nm). The dependence of electroluminescence (EL) spectra on the BCP layer thickness and operating voltage has been investigated quantitatively. It is shown that the emission colour of the devices changes from red to blue at 8 V when the BCP layer thickness changes from 1 to 10 nm. The emission colour of the devices also varies with the applying voltage even in a given device. The ratio of blue emission originating from 2P9PPF to the red emission originating from DCJTB increases with the applying voltage. Based on the hole blocking effect of the BCP layer, we deduced the dependence of this ratio on the BCP layer thickness and simulated the experimental result well. It is also proposed that the variation of the EL spectrum with the voltage can be attributed to the varying hole blocking effect under the varying electric field, which resulted in a recombination zone shift, and the exciton dissociation effect in the electric field

The colour-tuning effect of 2,9-dimethyl-4,7-diphenyl-1, 10-phenanthroline in blue-red organic light-emitting devices

Energy Technology Data Exchange (ETDEWEB)

Lin Jian [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Xia, Yi-Jie [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Tang Chao [Institute of Advanced Materials, Nanjing University of Posts and Telecommunications (NUPT), 66 XinMoFan Road, Nanjing 210003 (China); Yin Kun [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Zhong Gaoyu [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Ni Gang [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Peng Bo [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Hou Xiaoyuan [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Gan Fuxi [Institute of Advanced Materials, Fudan University, Shanghai 200433 (China); Huang Wei [Institute of Advanced Materials, Nanjing University of Posts and Telecommunications (NUPT), 66 XinMoFan Road, Nanjing 210003 (China)

2007-08-07

This paper reports the fabrication and measurement of organic light-emitting devices comprised of indium-tin-oxide (ITO)/4,4',4-prime-tris(N-carbazolyl)-triphenylamine (TCTA, 8 nm)/2-pyrenyl-9-phenyl-9-pyrenylfluorene(2P9PPF, 30 nm)/ bathocuproine (BCP, with different thickness)/Alq{sub 3} : DCJTB (DCJTB = 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7- tetramethyljulolidyl-9-enyl)-4H-pyran, Alq{sub 3} = tris(8-hydroxyquinolino) aluminium(III), 2% in mass ratio, 30 nm)/Mg : Ag(250 nm). The dependence of electroluminescence (EL) spectra on the BCP layer thickness and operating voltage has been investigated quantitatively. It is shown that the emission colour of the devices changes from red to blue at 8 V when the BCP layer thickness changes from 1 to 10 nm. The emission colour of the devices also varies with the applying voltage even in a given device. The ratio of blue emission originating from 2P9PPF to the red emission originating from DCJTB increases with the applying voltage. Based on the hole blocking effect of the BCP layer, we deduced the dependence of this ratio on the BCP layer thickness and simulated the experimental result well. It is also proposed that the variation of the EL spectrum with the voltage can be attributed to the varying hole blocking effect under the varying electric field, which resulted in a recombination zone shift, and the exciton dissociation effect in the electric field.

Electrical and Optical Characterization of Nanowire based Semiconductor Devices

Science.gov (United States)

Ayvazian, Talin

This research project is focused on a new strategy for the creation of nanowire based semiconductor devices. The main goal is to understand and optimize the electrical and optical properties of two types of nanoscale devices; in first type lithographically patterned nanowire electrodeposition (LPNE) method has been utilized to fabricate nanowire field effect transistors (NWFET) and second type involved the development of light emitting semiconductor nanowire arrays (NWLED). Field effect transistors (NWFETs) have been prepared from arrays of polycrystalline cadmium selenide (pc-CdSe) nanowires using a back gate configuration. pc-CdSe nanowires were fabricated using the lithographically patterned nanowire electrode- position (LPNE) process on SiO2 /Si substrates. After electrodeposition, pc-CdSe nanowires were thermally annealed at 300 °C x 4 h either with or without exposure to CdCl 2 in methanol a grain growth promoter. The influence of CdCl2 treatment was to increase the mean grain diameter as determined by X-ray diffraction pattern and to convert the crystal structure from cubic to wurtzite. Transfer characteristics showed an increase of the field effect mobility (mu eff) by an order of magnitude and increase of the Ion/I off ratio by a factor of 3-4. Light emitting devices (NW-LED) based on lithographically patterned pc-CdSe nanowire arrays have been investigated. Electroluminescence (EL) spectra of CdSe nanowires under various biases exhibited broad emission spectra centered at 750 nm close to the band gap of CdSe (1.7eV). To enhance the intensity of the emitted light and the external quantum efficiency (EQE), the distance between the contacts were reduced from 5 mum to less than 1 mum which increased the efficiency by an order of magnitude. Also, increasing the annealing temperature of nanowires from 300 °C x4 h to 450 This research project is focused on a new strategy for the creation of nanowire based semiconductor devices. The main goal is to understand

Blueshift of electroluminescence from single n-InP nanowire/p-Si heterojunctions due to the Burstein-Moss effect

International Nuclear Information System (INIS)

Liu, C; Dai, L; You, L P; Xu, W J; Qin, G G

2008-01-01

Single-crystalline n-type InP nanowires (NWs) with different electron concentrations were synthesized on Si substrates via the vapor phase transport method. The electrical properties of the InP nanowires were investigated by fabricating and measuring single NW field-effect transistors (FETs). Single InP NW/p + -Si heterojunctions were fabricated, and electroluminescence (EL) spectra from them were studied. It was found that both the photoluminescence (PL) spectra of the InP NWs and the EL spectra of the heterojunctions blueshift from 920 to 775 nm when the electron concentrations of the InP NWs increase from 2 x 10 17 to 1.4 x 10 19 cm -3 . The blueshifts can be attributed to the Burstein-Moss effect rather than the quantum confinement effect in the InP NWs. The large blueshifts observed in this study indicate a potential application of InP NWs in nano-multicolour displays.

Stimulated Emission from InAs (GaAs Monolayers Stacks Embedded in Al0.33Ga0.67As Ective Region

Directory of Open Access Journals (Sweden)

Dusan Pudis

2002-01-01

Full Text Available Our study is focused on the optical and electronic properties of InAs (GaAs monolayers embedded in Al0.33GA0.67As barrier layers investigated by temperature dependencies of electroluminescence spectra. The experimental results obtained from low temperature electroluminescence measurements of InAs (GaAs/Al0.33GA0.67As revealed the excellent emission spectra in the visib le range 630-690 nm. The stimulated emission from these structures across their cleavage planes has been observed at low  temperatures what is highly interesting for potential device applications.

Design and development of low-power driven hybrid electroluminescent lamp from carbon nanotube embedded phosphor material

International Nuclear Information System (INIS)

Yadav, Deepika; Mishra, Savvi; Shanker, Virendra; Haranath, D.

2013-01-01

Highlights: •We are first to report CNT embedded ZnS:Mn hybrid EL system. •Achieved efficient orange-red EL emission at low operating voltages ( AC ). •Facile technique to induce conductive paths inside the ZnS particle to trigger EL. •Detailed electrical characterization of EL lamp is presented. -- Abstract: We present a novel methodology to design a hybrid electroluminescent (EL) lamp by embedding carbon nanotubes (CNTs) inside the ZnS:Mn phosphor particles by conventional solid state diffusion technique. By doing so, the phosphor particles exhibited increase in EL brightness and efficiency at low operating voltages ( AC ). Interestingly, shorter the length of CNTs used, greater was the field enhancement effect and lower was the operating voltages to glow the EL lamps. The role of CNTs have been identified to form conductive paths inside the ZnS particle thereby triggering EL due to electron injection to luminescent centers (Mn 2+ ) at nominal voltages. In addition, a detailed electrical characterization of the novel EL lamp along with its spectral energy distribution studies are presented

Electroluminescence of organic light-emitting diodes consisting of an undoped (pbi)2Ir(acac) phosphorescent layer

Science.gov (United States)

Lei, Xia; Yu, Junsheng; Zhao, Juan; Jiang, Yadong

2011-11-01

The electroluminescence (EL) characteristics of phosphorescent organic light-emitting diodes (OLEDs) with an undoped bis(1,2-dipheny1-1H-benzoimidazole) iridium (acetylacetonate) [(pbi)2Ir(acac)] emissive layer (EML) of various film thicknesses were studied. The results showed that the intensity of green light emission decreased rapidly with the increasing thickness of (pbi)2Ir(acac), which was relevant to the triplet excimer emission. It suggested that the concentration quenching of monomer emission in the undoped (pbi)2Ir(acac) film was mainly due to the formation of triplet excimer and partly due to the triplet-triplet annihilation (TTA) and triplet-polaron annihilation (TPA). A green OLED with a maximum luminance of 26,531 cd/m2, a current efficiency of 36.2 cd/A, and a power efficiency of 32.4 lm/W was obtained, when the triplet excimer emission was eliminated. Moreover, the white OLED with low efficiency roll-off was realized due to the broadened recombination zone and reduced quenching effects in the EML when no electron blocking layer was employed.

Room Temperature Direct Band Gap Emission from Ge p-i-n Heterojunction Photodiodes

Directory of Open Access Journals (Sweden)

E. Kasper

2012-01-01

Full Text Available Room temperature direct band gap emission is observed for Si-substrate-based Ge p-i-n heterojunction photodiode structures operated under forward bias. Comparisons of electroluminescence with photoluminescence spectra allow separating emission from intrinsic Ge (0.8 eV and highly doped Ge (0.73 eV. Electroluminescence stems from carrier injection into the intrinsic layer, whereas photoluminescence originates from the highly n-doped top layer because the exciting visible laser wavelength is strongly absorbed in Ge. High doping levels led to an apparent band gap narrowing from carrier-impurity interaction. The emission shifts to higher wavelengths with increasing current level which is explained by device heating. The heterostructure layer sequence and the light emitting device are similar to earlier presented photodetectors. This is an important aspect for monolithic integration of silicon microelectronics and silicon photonics.

Synthesis of block copolymers with well-defined alternating chromophore and flexible spacer for electroluminescence application

Energy Technology Data Exchange (ETDEWEB)

Wang Haiqiao; Sun Qingjiang; Li Yongfang; Li Xiaoyu

2003-02-24

Two novel light-emitting block copolymers, poly[1,4,7,10-tetraoxadecane-1,10-diyl-1,4-naphthalene-1,2-ethenediyl-1,4- phenylene-1,2-ethenediyl-1,4-naphthalene] (TEO-DNVB) and poly[1,4,7,10-tetraoxadecane-1,10-diyl-1,4-naphthalene-1,2-ethenediyl- (2,5-dimethoxy-1,4-phenylene)-1,2-ethenediyl-1,4-naphthalene] (TEO-MDNVB), were synthesized by using the Wittig reaction. The block copolymers are composed of the fluorescent segments, 1,4-di[2-(1-naphthyl) vinyl] benzene (DNVB) or 2,5-dimethyloxy-1,4-di[2-(1-naphthyl) vinyl] benzene (MDNVB) and the flexible segments, tri(ethylene oxide) (TEO). The copolymers were characterized by Fourier transform infrared (FT-IR), {sup 1}H-nuclear magnetic resonance ({sup 1}H-NMR), ultraviolet-visible (UV-Vis), gel permeation chromatography (GPC) and cyclic voltammograms (CV). Thermal properties were investigated with differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) under nitrogen atmosphere. Cyclic voltammetric measurement reveals a reversible p-doping process. Efficient blue-green polymer light-emitting diodes (PLEDs) and polymer light-emitting electrochemical cells (PLECs) were successfully fabricated. The synthesis, characterization and the electroluminescent properties of the copolymers are reported in this paper.

Experiments on multi-stage light intensification by electro-luminescence; Experiences sur l'intensification de la lumiere en cascade par electroluminescence; Opyty po mnogokaskadnomu svetousileniyu (fotoumnozheniyu) posredstvom ehlektrosvecheniya; Experimentos sobre intensificacion en cascada de la luminosidad por electroluminiscencia

Energy Technology Data Exchange (ETDEWEB)

Owaki, K; Nakamura, T [Kobe Kogyo Corporation, Okubo, Akashi, Hyogo (Japan)

1962-04-15

In recent years, several papers on the solid-state image-intensifier by the use of electro-luminescent phosphor and photo-conductive materials have appeared as one of the important applications of solid-state electronics. It is convenient and important to use the solid-state intensifier for light amplification. The purpose of this experimental work is to achieve more amplification by cascading the intensifier in multi-stage. This paper first deals with the electrical and optical characteristics of a single-element lightintensifier, then points out briefly the advantage of employing parallel resistance with an electroluminescent- panel to improve its characteristics. Two types of photo-conductive cell were used, one was a sintered CdS cell and the other a CdS photo-sensitive powder, moulded with plastic binder. According to the results obtained on a single-element light-intensifier, two-stage and threestage light intensifiers were made and their characteristics were tested for various parallel resistances. In the three-stage light intensifier, the amplification of about 400 was obtained at 0.3 rlx in-put radiation, and these results suggest the possibility of obtaining more amplification at lower input radiation. The experimental results are believed to be applicable to a solid-state image-intensifier by devising a suitable construction. (author) [French] Au cours des dernieres annees, on a publie plusieurs communications sur le renforcateur d'images a cristal utilisant le phosphore electroluminescent et des matieres photoconductrices; c'est la une des principales applications de l'electronique de l'etat solide. Il est a la fois pratique et avantageux d'utiliser le renforcateur d'images a cristal pour l'amplification de la lumiere. Ces experiences visent a accroitre l'amplification en faisant cascader le renforcateur en plusieurs phases. Apres avoir presente les caracteristiques electriques et optiques d'un photomultiplicateur a un seul element, les auteurs exposent

Efficiency enhancement in a single emission layer yellow organic light emitting device: Contribution of CIS/ZnS quantum dot

International Nuclear Information System (INIS)

Demir, Nuriye; Oner, Ilker; Varlikli, Canan; Ozsoy, Cihan; Zafer, Ceylan

2015-01-01

Electroluminescence (EL) efficiency from a single emission layer solution processed yellow emitting polymer, i.e. poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(1,4-benzo-{2,10,3}-thiadiazole)] end-capped with dimethylphenyl (ADS233YE), is firstly enhanced by the optimization of stock polymer concentrations and the coating rates, and then with the addition of copper indium disulfide/zinc sulfide (CIS/ZnS) core/shell quantum dots (QDs). Using these bare core/shell QDs as the active layer in the studied device gave no EL at all. However, yellow EL with the maximum brightness of 56834 cd/m 2 , maximum current efficiency of 4.7 cd/A and maximum power efficiency of 2.3 lm/W is obtained from the device structure of indium tin oxide/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)/ADS233YE:0.4 wt.% CIS/ZnS QD/Ca/Al those of which correspond to approximately 4 and 2 folds of enhancements in the brightness and luminous and power efficiency values, respectively, compared to that of the device without CIS/ZnS. - Highlights: • Copper indium disulfide/zinc sulfide (CIS/ZnS) particles are synthesized. • Polymer light emitting diode performance of a yellow emitting polymer is enhanced. • The presence of CIS/ZnS in active layer enhanced the power efficiency two folds. • Optimum concentration of CIS/ZnS in polymer is 0.4 wt.%

Efficiency enhancement in a single emission layer yellow organic light emitting device: Contribution of CIS/ZnS quantum dot

Energy Technology Data Exchange (ETDEWEB)

Demir, Nuriye; Oner, Ilker; Varlikli, Canan, E-mail: canan.varlikli@ege.edu.tr; Ozsoy, Cihan; Zafer, Ceylan

2015-08-31

Electroluminescence (EL) efficiency from a single emission layer solution processed yellow emitting polymer, i.e. poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-(1,4-benzo-{2,10,3}-thiadiazole)] end-capped with dimethylphenyl (ADS233YE), is firstly enhanced by the optimization of stock polymer concentrations and the coating rates, and then with the addition of copper indium disulfide/zinc sulfide (CIS/ZnS) core/shell quantum dots (QDs). Using these bare core/shell QDs as the active layer in the studied device gave no EL at all. However, yellow EL with the maximum brightness of 56834 cd/m{sup 2}, maximum current efficiency of 4.7 cd/A and maximum power efficiency of 2.3 lm/W is obtained from the device structure of indium tin oxide/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)/ADS233YE:0.4 wt.% CIS/ZnS QD/Ca/Al those of which correspond to approximately 4 and 2 folds of enhancements in the brightness and luminous and power efficiency values, respectively, compared to that of the device without CIS/ZnS. - Highlights: • Copper indium disulfide/zinc sulfide (CIS/ZnS) particles are synthesized. • Polymer light emitting diode performance of a yellow emitting polymer is enhanced. • The presence of CIS/ZnS in active layer enhanced the power efficiency two folds. • Optimum concentration of CIS/ZnS in polymer is 0.4 wt.%.

Effect of interface voids on electroluminescence colors for ZnO microdisk/p-GaN heterojunction light-emitting diodes

Science.gov (United States)

Mo, Ran; Choi, Ji Eun; Kim, Hyeong Jin; Jeong, Junseok; Kim, Jong Chan; Kim, Yong-Jin; Jeong, Hu Young; Hong, Young Joon

2017-10-01

This study investigates the influence of voids on the electroluminescence (EL) emission color of ZnO microdisk/p-GaN heterojunction light-emitting diodes (LEDs). For this study, position-controlled microdisk arrays were fabricated on patterned p-GaN via wet chemical epitaxy of ZnO, and specifically, the use of trisodium citrate dihydrate (TCD) yielded high-density voids at the bottom of the microdisk. Greenish yellow or whitish blue EL was emitted from the microdisk LEDs formed with or without TCD, respectively, at reverse-bias voltages. Such different EL colors were found to be responsible for the relative EL intensity ratio between indigo and yellow emission peaks, which were originated from radiative recombination at p-GaN and ZnO, respectively. The relative EL intensity between dichromatic emissions is discussed in terms of (i) junction edge effect provoked by interfacial voids and (ii) electron tunneling probability depending on the depletion layer geometry.

Effect of the substituents on the photophysical, electrochemical and electroluminescence properties of OLED dopant Iridium bis(2-phenylbenzothiozolato- N,C2')(acetylacetonate)

Science.gov (United States)

Ivanov, P.; Tomova, R.; Petrova, P.

2014-12-01

The effect of two substituents: clorine and 1,3-diphenylpropane-1,3-dionate, placed on different position in the molecule of Iridium (III) bis(2-phenylbenzothiozolato-N,C2')- (acetylacetonate) (bt)2Ir(acac), on its electrochemical behaviour, photophysical and electroluminescence properties were investigated. Three complexes (bt)2Ir(acac), Iridium (III) bis[2-(4-chlorophenyl)benzothiazolato-N,C2']-acetylacetonate (Clbt)2Ir(acac), in which the Cl atom was introduced on the 4-position in the benzothiazole ring, and the new Iridium (Ill) bis[2 -phenylbenzothiazolato -N,C2'] -(1,3 -diphenylpropane-1,3 -dionate) (bt)2Ir(dbm), where ancillary acetylacetonate ligand was replaced by 1,3-diphenylpropane-1,3-dionate, were synthesized and characterised by 1H-NMR and elemental analysis. The HOMO/LUMO energy levels of the complexes were determined by cyclic voltammetry (CV) and their properties were established by UV-Visible and fluorescence spectroscopy. The application of (Clbt)2Ir(acac), (bt)2Ir(bsm) and (bt)2Ir(acac) as dopants in hole transporting layer (HTL) of Organic light- emitting diodes(OLEDs). It was found that with respect to the reference (bt)2Ir(acac): both LUMO and HOMO of the substituted complexes were shifted to more positive values accordingly with 0.23 and 0.19 eV for (Clbt)2Ir(acac) and 0.14 and 0.12 eV for (bt)2Ir(dbm). OLEDs doped with 1 w% of the complexes irradiated the warm white light with Commission internationale de l'eclairage (CIE) coordinates: 0.24;0.38 for (Clbt)2Ir(acac), 0.30;0.44 for (bt)2Ir(acac) and 0.28;0.46 for (bt)2Ir(dbm). Devices doped with 10 w% of all complexes irradiated in the yellow orange region of the spectrum.

Comparison of radiative and structural properties of 1.3 µm InxGa(1-x)As quantum-dot laser structures grown by metalorganic chemical vapor deposition and molecular-beam epitaxy: Effect on the lasing properties

NARCIS (Netherlands)

Passaseo, A.; Vittorio, de M.; Todaro, M.T.; Tarantini, I.; Giorgi, de M.; Cingolani, R.; Taurino, A.; Catalano, M.; Fiore, A.; Markus, A.; Chen, J.X.; Paranthoën, C.; Oesterle, U.; Ilegems, M.

2003-01-01

The authors have studied the radiative and structural properties of identical InxGa(1-x)As quantum dot laser structures grown by metalorg. CVD (MOCVD) and MBE. Despite the comparable emission properties found in the two devices by photoluminescence, electroluminescence, and photocurrent

Colloidal nanocrystals for quality lighting and displays: milestones and recent developments

Directory of Open Access Journals (Sweden)

Erdem Talha

2016-06-01

Full Text Available Recent advances in colloidal synthesis of nanocrystals have enabled high-quality high-efficiency light-emitting diodes, displays with significantly broader color gamut, and optically-pumped lasers spanning the whole visible regime. Here we review these colloidal platforms covering the milestone studies together with recent developments. In the review, we focus on the devices made of colloidal quantum dots (nanocrystals, colloidal quantum rods (nanorods, and colloidal quantum wells (nanoplatelets as well as those of solution processed perovskites and phosphor nanocrystals. The review starts with an introduction to colloidal nanocrystal photonics emphasizing the importance of colloidal materials for light-emitting devices. Subsequently,we continue with the summary of important reports on light-emitting diodes, in which colloids are used as the color converters and then as the emissive layers in electroluminescent devices. Also,we review the developments in color enrichment and electroluminescent displays. Next, we present a summary of important reports on the lasing of colloidal semiconductors. Finally, we summarize and conclude the review presenting a future outlook.

Synthesis and characterization of borane-terminated poly(silole-co-germole) for the evaluation of luminescent PLED.

Science.gov (United States)

Kim, Myoung-Hee; Lee, Jun; Kim, Jong-Hyun; Woo, Hee-Gweon; Kim, Bo-Hye; Yang, Kap Seung; Sohn, Honglae

2012-05-01

Codehydrocoupling (in the presence of various inorganic B, Al-hydrides) followed by borane-capping (with Ph2BCl) of 1,1-dihydrotetraphenylsilole (1) and 1,1-dihydrotetraphenylgermole (2) (9:1 mole ratio) gave electroluminescent poly(silole-co-germole)s containing borane-ends (3) in high yield. The polymerization yield and molecular weight with Selectrides increase in the order L-Selectride L-Selectride < Red-Al electroluminescent at 521 nm. The fluorescence quantum yield of 3 in toluene is (1.60 +/- 0.30) x 10(-2). The emission color is green and the maximum brightness of the device is 2,753 cd/m2 with a luminous efficiency of 0.66 Im/W. The borane end group exhibited no appreciable effect on the luminescent properties of 3. The electroluminescent copolymer 3 with boranyl end group is hence a good candidate for PLED fabrication.

Organic optoelectronics

CERN Document Server

Hu, Wenping; Gong, Xiong; Zhan, Xiaowei; Fu, Hongbing; Bjornholm, Thomas

2012-01-01

Written by internationally recognized experts in the field with academic as well as industrial experience, this book concisely yet systematically covers all aspects of the topic.The monograph focuses on the optoelectronic behavior of organic solids and their application in new optoelectronic devices. It covers organic electroluminescent materials and devices, organic photonics, materials and devices, as well as organic solids in photo absorption and energy conversion. Much emphasis is laid on the preparation of functional materials and the fabrication of devices, from materials synthesis a

Magnetic field enhanced electroluminescence in organic light emitting diodes based on electron donor-acceptor exciplex blends

Science.gov (United States)

Baniya, Sangita; Basel, Tek; Sun, Dali; McLaughlin, Ryan; Vardeny, Zeev Valy

2016-03-01

A useful process for light harvesting from injected electron-hole pairs in organic light emitting diodes (OLED) is the transfer from triplet excitons (T) to singlet excitons (S) via reverse intersystem crossing (RISC). This process adds a delayed electro-luminescence (EL) emission component that is known as thermally activated delayed fluorescence (TADF). We have studied electron donor (D)/acceptor(A) blends that form an exciplex manifold in which the energy difference, ΔEST between the lowest singlet (S1) and triplet (T1) levels is relatively small (exciplex blend is enhanced up to 40% by applying a relatively weak magnetic field of 50 mT at ambient. Moreover the MEL response is activated with activation energy similar that of the EL emission. This suggests that the large magneto-EL originates from an additional spin-mixing channel between singlet and triplet states of the generated exciplexes, which is due to TADF. We will report on the MEL dependencies on the temperature, bias voltage, and D-A materials for optimum OLED performance. Supported by SAMSUNG Global Research Outreach (GRO) program, and also by the NSF-Material Science & Engineering Center (MRSEC) program at the University of Utah (DMR-1121252).

Synthesis and photophysical characteristics of 2,7-fluorenevinylene-based trimers and their electroluminescence.

Science.gov (United States)

Mikroyannidis, John A; Fenenko, Larysa; Adachi, Chihaya

2006-10-19

Three new 2,7-fluorenevinylene-based trimers were synthesized and characterized. The synthesis was carried out by the Heck coupling reaction of 9,9-dihexyl-2,7-divinylfluorene with 2-(4-bromophenyl)-5-phenyl-1,3,4-oxadiazole, N,N-diphenyl-4-bromoaniline, or 3-bromopyrene to afford the trimers OXD, TPA, and PYR, respectively. All the trimers were readily soluble in common organic solvents such as tetrahydrofuran, dichloromethane, chloroform, and toluene. Their glass transition temperatures ranged from 33 to 60 degrees C. The UV-vis spectra showed an absorption maximum at lambda(a,max) = 379-417 nm with optical band gap of Eg = 2.47-2.66 eV. In solution, they emitted strong blue-green photoluminescence (PL) with PL maximum at lambda(f,max) = 455-565 nm and fluorescence quantum yield of Phi(f) = 0.65-0.74. On the other hand, in their spin-coated films, the PL efficiencies significantly decreased due to the presence of concentration quenching. All samples showed nanosecond transient lifetime containing two components, suggesting excimer formation. The organic light-emitting diodes (OLEDs) with OXD and TPA showed green emission with electroluminescence (EL) quantum efficiencies of eta(EL) approximately 10(-2)%, while very weak EL efficiency of eta(EL) approximately 10(-5)% was observed with PYR. The highest occupied molecular orbital (HOMO) levels of the films were found to be 5.05-5.75 eV.

In Situ Preparation of Metal Halide Perovskite Nanocrystal Thin Films for Improved Light-Emitting Devices.

Science.gov (United States)

Zhao, Lianfeng; Yeh, Yao-Wen; Tran, Nhu L; Wu, Fan; Xiao, Zhengguo; Kerner, Ross A; Lin, YunHui L; Scholes, Gregory D; Yao, Nan; Rand, Barry P

2017-04-25

Hybrid organic-inorganic halide perovskite semiconductors are attractive candidates for optoelectronic applications, such as photovoltaics, light-emitting diodes, and lasers. Perovskite nanocrystals are of particular interest, where electrons and holes can be confined spatially, promoting radiative recombination. However, nanocrystalline films based on traditional colloidal nanocrystal synthesis strategies suffer from the use of long insulating ligands, low colloidal nanocrystal concentration, and significant aggregation during film formation. Here, we demonstrate a facile method for preparing perovskite nanocrystal films in situ and that the electroluminescence of light-emitting devices can be enhanced up to 40-fold through this nanocrystal film formation strategy. Briefly, the method involves the use of bulky organoammonium halides as additives to confine crystal growth of perovskites during film formation, achieving CH 3 NH 3 PbI 3 and CH 3 NH 3 PbBr 3 perovskite nanocrystals with an average crystal size of 5.4 ± 0.8 nm and 6.4 ± 1.3 nm, respectively, as confirmed through transmission electron microscopy measurements. Additive-confined perovskite nanocrystals show significantly improved photoluminescence quantum yield and decay lifetime. Finally, we demonstrate highly efficient CH 3 NH 3 PbI 3 red/near-infrared LEDs and CH 3 NH 3 PbBr 3 green LEDs based on this strategy, achieving an external quantum efficiency of 7.9% and 7.0%, respectively, which represent a 40-fold and 23-fold improvement over control devices fabricated without the additives.

Electroluminescence pulse shape and electron diffusion in liquid argon measured in a dual-phase TPC

Energy Technology Data Exchange (ETDEWEB)

Agnes, P.; et al.

2018-02-05

We report the measurement of the longitudinal diffusion constant in liquid argon with the DarkSide-50 dual-phase time projection chamber. The measurement is performed at drift electric fields of 100 V/cm, 150 V/cm, and 200 V/cm using high statistics $^{39}$Ar decays from atmospheric argon. We derive an expression to describe the pulse shape of the electroluminescence signal (S2) in dual-phase TPCs. The derived S2 pulse shape is fit to events from the uppermost portion of the TPC in order to characterize the radial dependence of the signal. The results are provided as inputs to the measurement of the longitudinal diffusion constant DL, which we find to be (4.12 $\\pm$ 0.04) cm$^2$/s for a selection of 140keV electron recoil events in 200V/cm drift field and 2.8kV/cm extraction field. To study the systematics of our measurement we examine datasets of varying event energy, field strength, and detector volume yielding a weighted average value for the diffusion constant of (4.09 $\\pm$ 0.09) cm$^2$ /s. The measured longitudinal diffusion constant is observed to have an energy dependence, and within the studied energy range the result is systematically lower than other results in the literature.

FABRICATION OF ZNS THIN FILM FOR INORGANIC EL BY THE VACCUUM EVAPORATION

OpenAIRE

龍見, 雅美; 島谷, 圭市; 小西, 信行; 元木, 健作

2008-01-01

"Zinc sulfide is a typical material for inorganic electroluminescent(EL) device. Recently very high luminance and life time e has been reported on an inorganic EL device based on thin film zinc sulfide material. The present study tries to realize high quality zinc sulfide thin film for EL device. The thin film was grown by the vacuum evaporation method. In order to obtain stoichiometric thin film, the vacuum evaporation was carried out in a quasi-closed vessel under a condition of sulfur atmo...

Forschungszentrum Rossendorf, Institute of Ion Beam Physics and Materials Research. Annual report 2004

International Nuclear Information System (INIS)

Borany, J. von; Heera, V.; Helm, M.; Jaeger, H.U.; Moeller, W.

2005-01-01

The following topics are dealt with: Silicon based electrically driven microcavity LED, ultraviolet electroluminescence from a Gd-implanted Si-metal-oxide-semiconductor device, semiconductor quantum-cascade lasers, ion beam synthesis and morphology of semiconductor memories, ion implantation, films, sputtering, ion-beam induced destabilization of nanoparticles. (HSI)

Forschungszentrum Rossendorf, Institute of Ion Beam Physics and Materials Research. Annual report 2004

Energy Technology Data Exchange (ETDEWEB)

Borany, J. von; Heera, V.; Helm, M.; Jaeger, H.U.; Moeller, W. (eds.)

2005-07-01

The following topics are dealt with: Silicon based electrically driven microcavity LED, ultraviolet electroluminescence from a Gd-implanted Si-metal-oxide-semiconductor device, semiconductor quantum-cascade lasers, ion beam synthesis and morphology of semiconductor memories, ion implantation, films, sputtering, ion-beam induced destabilization of nanoparticles. (HSI)

Relationships between junction temperature, electroluminescence spectrum and ageing of light-emitting diodes

Science.gov (United States)

Vaskuri, Anna; Kärhä, Petri; Baumgartner, Hans; Kantamaa, Olli; Pulli, Tomi; Poikonen, Tuomas; Ikonen, Erkki

2018-04-01

We have developed spectral models describing the electroluminescence spectra of AlGaInP and InGaN light-emitting diodes (LEDs) consisting of the Maxwell-Boltzmann distribution and the effective joint density of states. One spectrum at a known temperature for one LED specimen is needed for calibrating the model parameters of each LED type. Then, the model can be used for determining the junction temperature optically from the spectral measurement, because the junction temperature is one of the free parameters. We validated the models using, in total, 53 spectra of three red AlGaInP LED specimens and 72 spectra of three blue InGaN LED specimens measured at various current levels and temperatures between 303 K and 398 K. For all the spectra of red LEDs, the standard deviation between the modelled and measured junction temperatures was only 2.4 K. InGaN LEDs have a more complex effective joint density of states. For the blue LEDs, the corresponding standard deviation was 11.2 K, but it decreased to 3.5 K when each LED specimen was calibrated separately. The method of determining junction temperature was further tested on white InGaN LEDs with luminophore coating and LED lamps. The average standard deviation was 8 K for white InGaN LED types. We have six years of ageing data available for a set of LED lamps and we estimated the junction temperatures of these lamps with respect to their ageing times. It was found that the LEDs operating at higher junction temperatures were frequently more damaged.

Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

Science.gov (United States)

Reyes, R.; Cremona, M.; Achete, C. A.

2011-01-01

Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq3) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq3/Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

Energy Technology Data Exchange (ETDEWEB)

Reyes, R [Facultad de Ingenieria Quimica y Textil, Universidad Nacional de Ingenieria, Av. Tupac Amaru SN, Lima (Peru); Cremona, M [Departamento de Fisica, PontifIcia Universidade Catolica de Rio de Janeiro, PUC-Rio, Cx. Postal 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Achete, C A, E-mail: rreyes@uni.edu.pe [Departamento de Engenheria Metalurgica e de Materiais, Universidade Federal do Rio de Janeiro, Cx. Postal 68505, Rio de Janeiro, RJ, CEP 21945-970 (Brazil)

2011-01-01

Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq{sub 3}) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq{sub 3}/Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

Light emission in forward and reverse bias operation in OLED with amorphous silicon carbon nitride thin films

International Nuclear Information System (INIS)

Reyes, R; Cremona, M; Achete, C A

2011-01-01

Amorphous silicon carbon nitride (a-SiC:N) thin films deposited by magnetron sputtering were used in the structure of an organic light emitting diode (OLED), obtaining an OLED operating in forward and reverse bias mode. The device consist of the heterojunction structure ITO/a-SiC:N/Hole Transport Layer (HTL)/ Electron Transport Layer (ETL)/a-SiC:N/Al. As hole transporting layer was used a thin film of 1-(3-methylphenyl)-1,2,3,4 tetrahydroquinoline - 6 - carboxyaldehyde - 1,1'- diphenylhydrazone (MTCD), while the tris(8-hydroxyquinoline aluminum) (Alq 3 ) is used as electron transport and emitting layer. A significant increase in the voltage operation compared to the conventional ITO/MTCD/Alq 3 /Al structure was observed, so the onset of electroluminescence occurs at about 22 V in the forward and reverse bias mode of operation. The electroluminescence spectra is similar in both cases, only slightly shifted 0.14 eV to lower energies in relation to the conventional device.

-MoS2 Lateral Heterojunctions

KAUST Repository

Li, Ming-yang

2018-02-28

2D layered heterostructures have attracted intensive interests due to their unique optical, transport, and interfacial properties. The laterally stitched heterojunction based on dissimilar 2D transition metal dichalcogenides forms an intrinsic p–n junction without the necessity of applying an external voltage. However, no scalable processes are reported to construct the devices with such lateral heterostructures. Here, a scalable strategy, two-step and location-selective chemical vapor deposition, is reported to synthesize self-aligned WSe2–MoS2 monolayer lateral heterojunction arrays and demonstrates their light-emitting devices. The proposed fabrication process enables the growth of high-quality interfaces and the first successful observation of electroluminescence at the WSe2–MoS2 lateral heterojunction. The electroluminescence study has confirmed the type-I alignment at the interface rather than commonly believed type-II alignment. This self-aligned growth process paves the way for constructing various 2D lateral heterostructures in a scalable manner, practically important for integrated 2D circuit applications.

Exciplex emission and decay of co-deposited 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

Science.gov (United States)

Huang, Qingyu; Zhao, Suling; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian

2014-04-01

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m2, as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m-2. The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence.

Optimal thickness of hole transport layer in doped OLEDs

Energy Technology Data Exchange (ETDEWEB)

Zhou, Y.C.; Zhou, J.; Zhao, J.M.; Zhang, S.T.; Zhan, Y.Q.; Wang, X.Z.; Wu, Y.; Ding, X.M.; Hou, X.Y. [Fudan University, Surface Physics Laboratory (National Key Laboratory), Shanghai (China)

2006-06-15

Current-voltage (I-V) and electroluminescence (EL) characteristics of organic light-emitting devices with N,N'-Di-[(1-naphthalenyl)-N,N'-diphenyl]-(1,1'-biphenyl)-4,4'-diamine (NPB) of various thicknesses as the hole transport layer, and tris(8-hydroxyquinoline)aluminum (Alq{sub 3}) selectively doped with 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM) as the electron transport layer, have been investigated. A trapped charge induced band bend model is proposed to explain the I-V characteristics. It is suggested that space charge changes the injection barrier and therefore influences the electron injection process in addition to the carrier transport process. Enhanced external quantum efficiency of the devices due to the electron blocking effect of an inserted NPB layer is observed. The optimal thickness of the NPB layer is experimentally determined to be 12{+-}3 nm in doped devices, a value different from that for undoped devices, which is attributed to the electron trap effect of DCM molecules. This is consistent with the result that the proportion of Alq{sub 3} luminescence in the total electroluminescence (EL) spectra increases with NPB thickness up to 12 nm under a fixed bias. (orig.)

Electroluminescence analysis of injection-enhanced annealing of electron irradiation-induced defects in GaInP top cells for triple-junction solar cells

Energy Technology Data Exchange (ETDEWEB)

Yi, Tiancheng; Lu, Ming; Yang, Kui; Xiao, Pengfei; Wang, Rong, E-mail: wangr@bnu.edu.cn

2014-09-15

Direct injection-enhanced annealing of defects in a GaInP top cell for GaInP/GaAs/Ge triple-junction solar cells irradiated with 1.8 MeV electrons with a fluence of 1 × 10{sup 15} cm{sup −2} has been observed and analyzed using electroluminescence (EL) spectra. Minority-carrier injection under forward bias conditions is observed to enhance defect annealing in the GaInP top cell, and recovery of the EL intensity of the GaInP top cell was observed even at room temperature. Moreover, the injection-enhanced defect annealing rates obey a simple Arrhenius law; therefore, the annealing activation energy was determined and is equal to 0.51 eV. Lastly, the H2 defect has been identified as the primary non-radiative recombination center based on a comparison of the annealing activation energies.

1.54 μm Er3+ electroluminescence from an erbium-compound-doped organic light emitting diode with a p-type silicon anode

International Nuclear Information System (INIS)

Zhao, W Q; Wang, P F; Ran, G Z; Ma, G L; Zhang, B R; Liu, W M; Wu, S K; Dai, L; Qin, G G

2006-01-01

By doping an erbium complex, erbium (III) 2, 4-pentanedionate (Er(acac) 3 ), into the ALQ layer, we fabricate a series of infrared emission organic light emitting diodes (OLED) with structures of p-Si/SiO 2 /NPB/ALQ/ ALQ:Er(acac) 3 /ALQ/Sm/Au, where p-Si is the anode and Sm/Au is the cathode. The 1.54 μm emission from Er 3+ is observed. The impact of doping level of Er(acac) 3 in ALQ on 1.54 μm electroluminescence (EL) intensity is studied, and the best mass ratio of Er(acac) 3 to ALQ is found at 1:60. A competitive EL mechanism from the ALQ and Er(acac) 3 is found and the Er 3+ ions excitations are attributed to energy transfer from the ligands to Er ions

Exciplex emission and decay of co-deposited 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

Energy Technology Data Exchange (ETDEWEB)

Huang, Qingyu; Zhao, Suling, E-mail: slzhao@bjtu.edu.cn; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Beijing Jiaotong University, Beijing 100044 (China); Institute of Optoelectronics Technology, Beijing Jiaotong University, Beijing 100044 (China)

2014-04-21

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m{sup 2}, as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m{sup −2}. The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence.

Exciplex emission and decay of co-deposited 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

International Nuclear Information System (INIS)

Huang, Qingyu; Zhao, Suling; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian

2014-01-01

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m 2 , as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m −2 . The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence

3D Printed Electroluminescent Light Panels - FY17

Data.gov (United States)

National Aeronautics and Space Administration — Task 1: Construct EL devices using both commercially available inks and MSFC developed inks starting with screen-printing methods as a baseline Task 2:...

Highly transparent and rollable PVA-co-PE nanofibers synergistically reinforced with epoxy film for flexible electronic devices.

Science.gov (United States)

Xiong, Bing; Zhong, Weibing; Zhu, Qing; Liu, Ke; Li, Mufang; Sun, Gang; Wang, Dong

2017-12-14

The development of electronics towards a more functions-integrated, flexible and stretchable direction requires mechanically flexible substrates with high thermal and dimensional stability and optical transparency. Herein, rolls of an optically transparent PVA-co-PE nanofibrous membrane/epoxy composite with synergistically enhanced thermal stability, very low CTE, and outstanding mechanical properties are reported. The nanoscale size, the unique inter-stack structure, and the strong interfacial interactions between the PVA-co-PE nanofibers and the epoxy contribute to the synergistic effects. Because of the match between the refractive index (RI) of the PVA-co-PE nanofibers and the epoxy matrix, the visible light transmittance of nanocomposite film could be as high as 85% and the composite film was still optically transparent with a nanofiber loading content of up to 61.7 wt%. The break strength and compliance matrix of the composite film with a high fiber loading of 61.7 wt% increased by 2.3 times of that of the neat epoxy film and exceeded 3000 m 2 N -1 , respectively. PVA-co-PE nanofibers have a very low CTE value (3.634 × 10 -6 K -1 ) and could be applicable as a reinforcement to reduce the thermal expansion of epoxy. Furthermore, we developed a flexible alternating current electroluminescent (ACEL) device based on the transparent composite film and the experimental results showed that the transparent composite film could serve as substrate for flexible electronic devices. In addition, their electrical and optical properties were evaluated.

Influence of the thickness of electrochemically deposited polyaniline used as hole transporting layer on the behaviour of polymer light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Alonso, J.L. [Dpto. de Fisica y Arquitectura de Computadores, Universidad Miguel Hernandez, Av. de la Universidad s/n, Ed. Torrepinet, 03202, Elche, Alicante (Spain)], E-mail: j.l.alonso@umh.es; Ferrer, J.C. [Dpto. de Fisica y Arquitectura de Computadores, Universidad Miguel Hernandez, Av. de la Universidad s/n, Ed. Torrepinet, 03202, Elche, Alicante (Spain); Cotarelo, M.A.; Montilla, F. [Dpto. de Quimica Fisica e Instituto Universitario de Materiales de Alicante, Apdo. de Correos 99, E-03080, Alicante (Spain); Fernandez de Avila, S. [Dpto. de Fisica y Arquitectura de Computadores, Universidad Miguel Hernandez, Av. de la Universidad s/n, Ed. Torrepinet, 03202, Elche, Alicante (Spain)

2009-02-27

An experimental study about the influence of the thickness of electrochemically deposited polyaniline (PANI), used as hole-transporting layer, on the behaviour of polymer light emitting diodes is presented. Two sets of devices with a different conjugated polymer used as active layer were prepared. Poly(9-vinylcarbazole) was used for the first type of devices, whereas Poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylene-vinylene] was used for the second type. Each set consists of five polymeric diodes in which the hole-transporting layer has been varied. In one case of each set no layer was deposited, in other one a Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) layer was deposited, and in the rest of the diodes a different thickness of electrochemically deposited PANI was employed. The optic and electronic characterization of the devices show that controlling the thickness of the PANI hole transporting layer, both the maximum emission peak of the electroluminescence curves and the driving voltage could be tuned. Furthermore, an exponential behaviour has been demonstrated for the maximum intensity of the electroluminescence curves as a function of the applied excitation voltage between anode and cathode.

Influence of the thickness of electrochemically deposited polyaniline used as hole transporting layer on the behaviour of polymer light-emitting diodes

International Nuclear Information System (INIS)

Alonso, J.L.; Ferrer, J.C.; Cotarelo, M.A.; Montilla, F.; Fernandez de Avila, S.

2009-01-01

An experimental study about the influence of the thickness of electrochemically deposited polyaniline (PANI), used as hole-transporting layer, on the behaviour of polymer light emitting diodes is presented. Two sets of devices with a different conjugated polymer used as active layer were prepared. Poly(9-vinylcarbazole) was used for the first type of devices, whereas Poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylene-vinylene] was used for the second type. Each set consists of five polymeric diodes in which the hole-transporting layer has been varied. In one case of each set no layer was deposited, in other one a Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) layer was deposited, and in the rest of the diodes a different thickness of electrochemically deposited PANI was employed. The optic and electronic characterization of the devices show that controlling the thickness of the PANI hole transporting layer, both the maximum emission peak of the electroluminescence curves and the driving voltage could be tuned. Furthermore, an exponential behaviour has been demonstrated for the maximum intensity of the electroluminescence curves as a function of the applied excitation voltage between anode and cathode

Hybrid p-n junction light-emitting diodes based on sputtered ZnO and organic semiconductors

International Nuclear Information System (INIS)

Na, Jong H.; Kitamura, M.; Arita, M.; Arakawa, Y.

2009-01-01

We fabricated light-emitting hybrid p-n junction devices using low temperature deposited ZnO and organic films, in which the ZnO and the organic films served as the n- and p-type component, respectively. The devices have a rectification factor as high as ∼10 3 and a current density greater than 2 A/cm 2 . Electroluminescence of the hybrid device shows the mixture of the emission bands arising from radiative charge recombination in organic and ZnO. The substantial device properties could provide various opportunities for low cost and large area multicolor light-emitting sources.

Improved efficiency in OLEDs with a thin Alq3 interlayer

International Nuclear Information System (INIS)

Lian Jiarong; Yuan Yongbo; Cao Lingfang; Zhang Jie; Pang Hongqi; Zhou Yunfei; Zhou Xiang

2007-01-01

We demonstrate an improved efficiency in OLEDs with a thin Alq 3 interlayer, which is inserted into the hole-transport layer for adjusting the hole-injection and transport, and improving the hole-electron balance. The thin Alq 3 interlayer can effectively influence the electrical performance and electroluminescence (EL) efficiency of the devices. The devices with an optimum Alq 3 interlayer exhibit a maximum EL efficiency of around 3.3 cd/A, which is improved by a factor of two over the conventional devices (1.6 cd/A) without the interlayer

Synthesis and characterization of stannane-terminated poly(silole-co-germole) for the evaluation of luminescent polymeric light-emitting diode.

Science.gov (United States)

Kim, Myoung-Hee; Kim, Jong Hyun; Pyo, Jung; Woo, Hee-Gweon; Yang, Kap-Seung; Ko, Young Chun; Roh, Sung-Hee; Kim, Whan Gi

2011-05-01

Codehydrocoupling (with various inorganic hydrides) followed by stannane-capping (with Ph2SnHCI) of 1,1-dihydrotetraphenylsilole (1) and 1,1-dihydrotetraphenylgermole (2) (9:1 mol ratio) produces electroluminescent stannane-terminated poly(silole-co-germole)s (3) in high yield. The polymerization yield and molecular weight with Selectride increase in the order L-Selectride L-Selectride < Red-Al < N-Selectride < K-Selectride < Super-Hydride. The copolymer 3, a good candidate for PLED fabrication, emits at 523 nm and are electroluminescent at 521 nm. The fluorescence quantum yield of 3 in toluene is (1.61 +/- 0.29) x 10(-2). The emission color is green. The maximum brightness of the device is 3,750 cd/m2 with a luminous power efficiency of 0.67 Im/W.

Preparation and characterization of electroluminescent devices based on complexes of β-diketonates of Tb3+, Eu3+, Gd3+ ions with macrocyclic ligands and UO22+ films

International Nuclear Information System (INIS)

Gibelli, Edison Bessa

2010-01-01

Complexes containing Rare Earth ions are of great interest in the manufacture of electro luminescent devices as organic light emitting devices (OLED). These devices, using rare earth trivalent ions (TR 3+ ) as emitting centers, show high luminescence with extremely fine spectral bands due to the structure of their energy levels, long life time and high quantum efficiency. This work reports the preparation of Rare Earth β-diketonate complexes (Tb 3+ , Eu 3+ and Gd 3+ ) and (tta - thenoyltrifluoroacetonate and acac - acetylacetonate) containing a ligand macrocyclic crown ether (DB18C6 - dibenzo18coroa6) and polymer films of UO 2 2+ . The materials were characterized by complexometric titration with EDTA, CH elemental analysis, near infrared absorption spectroscopy, thermal analysis, X-ray diffraction (powder method) and luminescence spectroscopy. For manufacturing the OLED it was used the technique of deposition of thin films by physical vapor (PVD, Physical Vapor Deposition). (author)

Method for Aluminum Oxide Thin Films Prepared through Low Temperature Atomic Layer Deposition for Encapsulating Organic Electroluminescent Devices

Directory of Open Access Journals (Sweden)

Hui-Ying Li

2015-02-01

Full Text Available Preparation of dense alumina (Al2O3 thin film through atomic layer deposition (ALD provides a pathway to achieve the encapsulation of organic light emitting devices (OLED. Unlike traditional ALD which is usually executed at higher reaction n temperatures that may affect the performance of OLED, this application discusses the development on preparation of ALD thin film at a low temperature. One concern of ALD is the suppressing effect of ambient temperature on uniformity of thin film. To mitigate this issue, the pumping time in each reaction cycle was increased during the preparation process, which removed reaction byproducts and inhibited the formation of vacancies. As a result, the obtained thin film had both high uniformity and density properties, which provided an excellent encapsulation performance. The results from microstructure morphology analysis, water vapor transmission rate, and lifetime test showed that the difference in uniformity between thin films prepared at low temperatures, with increased pumping time, and high temperatures was small and there was no obvious influence of increased pumping time on light emitting performance. Meanwhile, the permeability for water vapor of the thin film prepared at a low temperature was found to reach as low as 1.5 × 10−4 g/(m2·day under ambient conditions of 25 °C and 60% relative humidity, indicating a potential extension in the lifetime for the OLED.

Generalized detailed balance theory of solar cells

Energy Technology Data Exchange (ETDEWEB)

Kirchartz, Thomas

2009-12-12

The principle of detailed balance is the requirement that every microscopic process in a system must be in equilibrium with its inverse process, when the system itself is in thermodynamic equilibrium. This detailed balance principle has been of special importance for photovoltaics, since it allows the calculation of the limiting efficiency of a given solar cell by defining the only fundamental loss process as the radiative recombination of electron/hole pairs followed by the emission of a photon. In equilibrium, i.e. in the dark and without applied voltage, the absorbed and emitted photon flux must be equal due to detailed balance. This equality determines the radiative recombination from absorption and vice versa. While the classical theory of photovoltaic efficiency limits by Shockley and Queisser considers only one detailed balance pair, namely photogeneration and radiative recombination, the present work extends the detailed balance principle to any given process in the solar cell. Applying the detailed balance principle to the whole device leads to two major results, namely (i) a model that is compatible with the Shockley-Queisser efficiency limit for efficient particle transport, while still being able to describe non-ideal and non-linear solar cells, and (ii) an analytical relation between electroluminescent emission and photovoltaic action of a diode that is applied to a variety of different solar cells. This thesis presents several variations of a detailed balance model that are applicable to different types of solar cells. Any typical inorganic solar cell is a mainly bipolar device, meaning that the current is carried by electrons and holes. The detailed balance model for pn-type and pin-type bipolar solar cells is therefore the most basic incorporation of a detailed balance model. The only addition compared to the classical diode theory or compared to standard one-dimensional device simulators is the incorporation of photon recycling, making the model

Carrier injection and recombination processes in perovskite CH3NH3PbI3 solar cells studied by electroluminescence spectroscopy

Science.gov (United States)

Handa, Taketo; Okano, Makoto; Tex, David M.; Shimazaki, Ai; Aharen, Tomoko; Wakamiya, Atsushi; Kanemitsu, Yoshihiko

2016-02-01

Organic-inorganic hybrid perovskite materials, CH3NH3PbX3 (X = I and Br), are considered as promising candidates for emerging thin-film photovoltaics. For practical implementation, the degradation mechanism and the carrier dynamics during operation have to be clarified. We investigated the degradation mechanism and the carrier injection and recombination processes in perovskite CH3NH3PbI3 solar cells using photoluminescence (PL) and electroluminescence (EL) imaging spectroscopies. By applying forward bias-voltage, an inhomogeneous distribution of the EL intensity was clearly observed from the CH3NH3PbI3 solar cells. By comparing the PL- and EL-images, we revealed that the spatial inhomogeneity of the EL intensity is a result of the inhomogeneous luminescence efficiency in the perovskite layer. An application of bias-voltage for several tens of minutes in air caused a decrease in the EL intensity and the conversion efficiency of the perovskite solar cells. The degradation mechanism of perovskite solar cells under bias-voltage in air is discussed.

Pure white OLED based on an organic small molecule: 2,6-Di(1H-benzo[d]imidazol-2-yl)pyridine

Science.gov (United States)

Liu, Jian

2015-10-01

2,6-Di(1H-benzo[d]imidazol-2-yl)pyridine (DBIP) was synthesized. The single-crystal structure of DBIP was resolved. DBIP-based OLED was fabricated. The electroluminescence for the device corresponds to a pure white emission. In addition, thermal stability, UV-vis, photoluminescence and electrochemical behaviors of DBIP were investigated as well.

White organic light emitting diodes based on DCM dye sandwiched in 2-methyl-8-hydroxyquinolinolatolithium

Energy Technology Data Exchange (ETDEWEB)

Kumar, Amit [Center for Organic Electronics, Polymeric and Soft Materials Section, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Department of Chemistry, M.D. University, Rohtak, Haryana 124001 (India); Srivastava, Ritu, E-mail: ritu@mail.nplindia.ernet.i [Center for Organic Electronics, Polymeric and Soft Materials Section, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Bawa, Sukhwant S. [Center for Organic Electronics, Polymeric and Soft Materials Section, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Singh, Devender; Singh, Kapoor [Department of Chemistry, M.D. University, Rohtak, Haryana 124001 (India); Chauhan, Gayatri [Center for Organic Electronics, Polymeric and Soft Materials Section, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi 110012 (India); Singh, Ishwar [Department of Chemistry, M.D. University, Rohtak, Haryana 124001 (India); Kamalasanan, Modeeparampil N. [Center for Organic Electronics, Polymeric and Soft Materials Section, National Physical Laboratory (Council of Scientific and Industrial Research), Dr. K.S. Krishnan Road, New Delhi 110012 (India)

2010-08-15

Stable white electroluminescence (EL) has been achieved from organic LED, in which an ultrathin 4-(dicyanomethylene)-2-methyl-6-(p-dimethyl-aminostyryl)-4H-pyran (DCM) dye layer has been inserted in between two 2-methyl-8-hydroxyquinolinolatolithium [LiMeq] emitter layer and by optimizing the position of the DCM dye layer from the {alpha}-NPD/LiMeq interface. Electroluminescence spectra, current-voltage-luminescence (I-V-L) characteristics of the devices have been studied by changing the position of the dye layer. As the distance of DCM layer from {alpha}-NPD/LiMeq interface is increased, the intensity of host emission enhances rapidly. Introduction of thin layer of DCM in emissive layer increases the turn on voltage. The best Commission International de L' Eclairage (CIE) coordinates i.e. (0.32, 0.33) were obtained with device structure ITO/{alpha}-NPD(30 nm) /LiMeq(10 nm)/DCM(1 nm)/LiMeq(25 nm)/BCP(6 nm)/Alq{sub 3}(28 nm)/LiF(1 nm)/Al(100 nm). The EL spectrum covers the whole visible spectra range 400-700 nm. The color rendering index (CRI) for our best white light (Device 4) is 47.4. The device shows very good color stability in terms of CIE coordinates with voltages. The maximum luminescence 1240 cd/m{sup -2} has been achieved at 19 V.

Organic light-emitting diodes based on 9-(2-naphthyl)anthracene derivatives with a triphenylsilane unit as the deep-blue emitting layer

Energy Technology Data Exchange (ETDEWEB)

Song, Ji Young; Lee, Seul Bee [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Lee, Seok Jae [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@wow.hongik.ac.kr [Department of Information Display, Hongik University, Seoul 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

2015-02-27

A series of 9-(2-naphthyl)anthracene derivatives with a triphenylsilane unit, which prevented molecular aggregation and self-quenching effect, was designed and synthesized. By using various bridges between the 9-(2-naphthyl)anthracene group and the triphenylsilane unit, five deep-blue emitters were obtained and applied as non-doped emitting materials in organic light-emitting diodes (OLEDs) with a device structure of indium–tin-oxide (ITO) (180 nm)/4,4-bis(N-(1-naphthyl)-N-phenylamino)biphenyl (NPB) (50 nm)/emitting materials (30 nm)/4,7-diphenyl-1,10-phenanthroline (Bphen) (30 nm)/lithium quinolate (Liq) (2 nm)/Aluminium (100 nm). All devices showed blue emissions and their electroluminescence efficiencies are sensitive to the structural changes of the emitting materials. In particular, a device using 9-(2-naphthalenyl)-10-[6-(triphenylsilyl)-2-naphthalenyl]-anthracene (4) exhibited high luminous, power and quantum efficiencies of 2.28 cd/A, 1.42 lm/W and 2.40% at 20 mA/cm{sup 2}, respectively, and this device showed the deep blue emission with the CIE coordinates of (0.16, 0.10) at 6.0 V. - Highlights: • We synthesized 9-(2-naphthyl)anthracene derivatives with a triphenylsilane unit. • We study the conjugation-length effect on the electroluminescence properties. • The bulky triphenylsilane-anthracene derivatives show resistance to self-aggregation.

Interface Engineering and Morphology Study of Thin Film Organic-Inorganic Halide Perovskite Optoelectronic Devices

Science.gov (United States)

Meng, Lei

significantly improved compared with cells made with organic layers. Degradation mechanisms were investigated and important guidelines were derived for future device design with a view to achieving both highly efficient and stable solar devices. Organometal halide based perovskite material has great optoelectronic proprieties, for example, shallow traps, benign grain boundaries and high diffusion length. The perovskite LEDs show pure electroluminescence (EL) with narrow full width at half maximum (FWHM), which is an advantage for display, lighting or lasing applications. In chapter five, perovskite LEDs are demonstrated employing solution processed charge injection layers with a quantum efficiency of 1.16% with a very low driving voltage.

Nanocluster-rich SiO2 layers produced by ion beam synthesis: electrical and optoelectronic properties

International Nuclear Information System (INIS)

Gebel, T.

2002-07-01

The main goal of this work is to investigate correlations between microstructural, electrical and optical properties of the devices. Chapter 3 gives an overview about the fabrication process and the methods used for the characterization of the devices. The microstructure of the devices is described in chapter 4 and the results of electrical and optical investigations are presented in chapter 5 and 6, respectively. The aim of the investigations is to get a better understanding of the charge transport, the charge storage and the mechanism of the electroluminescence. This knowledge is necessary for the further optimization of the devices and for possible applications. (orig.)

Influence of bismuth on properties and microstructures of Sr0⋅5Ba0 ...

Indian Academy of Sciences (India)

tric detectors, tunable microwave devices, phase shifters, electroluminescence display etc (Liou and Chiou 1997;. Liu et al 2000). So, Sr1–xBaxTiO3 films have gained in- creasing interest in the investigation and fabrication of thin films. The exploitation of BST thin films for applications in nonvolatile memory of high memory ...

Electron lucky-drift impact ionization coefficients of ZnS : Mn

Indian Academy of Sciences (India)

can also be used to calculate the impact ionization coefficients of high electron energy of. ZnS:Mn without ... Electroluminescent devices (ZnS:Mn) recently are of great interest in industry as well as in information technology [1–4]. Understanding .... data in the case of electron in ZnS from two sources, which were reported by.

Photovoltaic effect on the performance enhancement of organic light-emitting diodes with planar heterojunction architecture

Energy Technology Data Exchange (ETDEWEB)

Zhao, Dan; Huang, Wei; Guo, Hao [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Wang, Hua, E-mail: wanghua001@tyut.edu.cn [Research Center of Advanced Materials Science and Technology, Taiyuan University of Technology (TYUT), Taiyuan 030024 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2017-04-15

Highlights: • The photovoltaic effect on the performance of OLEDs was studied. • The device performance with different planar heterojunctions was investigated. • The mechanism relies on the overlap of electroluminescence and absorption spectrum. - Abstract: Organic light-emitting diodes (OLEDs) with planar heterojunction (PHJ) architecture consisting of photovoltaic organic materials of fullerene carbon 60 (C{sub 60}) and copper (II) phthalocyanine (CuPc) inserted between emitting unit and cathode were constructed, and the photovoltaic effect on OLEDs performance was studied. The electroluminescent (EL) characteristics and mechanism of device performance variation without and with different PHJs (herein including C{sub 60}/CuPc, CuPc/C{sub 60} and CuPc) were systematically investigated in red, green and blue OLEDs. Of the three combinations, OLEDs with C{sub 60}/CuPc showed the highest efficiency. It is revealed that the photovoltaic C{sub 60}/CuPc PHJ can absorb part of photons, which are radiated from emission zone, then form excitons, and dissociated into free charges. Consequently, the high device efficiency of OLEDs performance improvement was acquired. This research demonstrates that PHJ consisting of two n- and p-type photovoltaic organic materials could be a promising methodology for high performance OLEDs.

Photovoltaic effect on the performance enhancement of organic light-emitting diodes with planar heterojunction architecture

International Nuclear Information System (INIS)

Zhao, Dan; Huang, Wei; Guo, Hao; Wang, Hua; Yu, Junsheng

2017-01-01

Highlights: • The photovoltaic effect on the performance of OLEDs was studied. • The device performance with different planar heterojunctions was investigated. • The mechanism relies on the overlap of electroluminescence and absorption spectrum. - Abstract: Organic light-emitting diodes (OLEDs) with planar heterojunction (PHJ) architecture consisting of photovoltaic organic materials of fullerene carbon 60 (C_6_0) and copper (II) phthalocyanine (CuPc) inserted between emitting unit and cathode were constructed, and the photovoltaic effect on OLEDs performance was studied. The electroluminescent (EL) characteristics and mechanism of device performance variation without and with different PHJs (herein including C_6_0/CuPc, CuPc/C_6_0 and CuPc) were systematically investigated in red, green and blue OLEDs. Of the three combinations, OLEDs with C_6_0/CuPc showed the highest efficiency. It is revealed that the photovoltaic C_6_0/CuPc PHJ can absorb part of photons, which are radiated from emission zone, then form excitons, and dissociated into free charges. Consequently, the high device efficiency of OLEDs performance improvement was acquired. This research demonstrates that PHJ consisting of two n- and p-type photovoltaic organic materials could be a promising methodology for high performance OLEDs.

Enhanced luminescence of rare-earth complexes Tb(1-x)Eu(x)(m-NBA)3Phen in ZnS.

Science.gov (United States)

Lv, Yuguang; Zhang, Jingchang; Cao, Weiliang; Song, Lin; Xu, Zheng

2008-07-01

Rare-earth ternary complexes Tb(1-x)Eu(x)(m-NBA)(3)Phen (X=1, 0.25, 0.5, 0.75, 1.0) were synthesized and characterized by IR, DTA-TG, UV, fluorescent spectra and elemental analysis. It was found that luminescence of Eu(3+) complex was enhanced by doped with Tb(3+). It is proved by TG curve that the complexes are stable, ranging from ambient temperature to 360 degrees C in air. The organic-inorganic combined structural device was fabricated, and the electroluminescence intensity of the combined structural device was improved compared with the device of the purely organic components.

Enhanced luminescence of rare-earth complexes Tb 1- xEu x( m-NBA) 3Phen in ZnS

Science.gov (United States)

Lv, Yuguang; Zhang, Jingchang; Cao, Weiliang; Song, Lin; Xu, Zheng

2008-07-01

Rare-earth ternary complexes Tb 1- xEu x( m-NBA) 3Phen ( X = 1, 0.25, 0.5, 0.75, 1.0) were synthesized and characterized by IR, DTA-TG, UV, fluorescent spectra and elemental analysis. It was found that luminescence of Eu 3+ complex was enhanced by doped with Tb 3+. It is proved by TG curve that the complexes are stable, ranging from ambient temperature to 360 °C in air. The organic-inorganic combined structural device was fabricated, and the electroluminescence intensity of the combined structural device was improved compared with the device of the purely organic components.

Structural and optical properties of silicon rich oxide films in graded-stoichiometric multilayers for optoelectronic devices

Energy Technology Data Exchange (ETDEWEB)

Palacios-Huerta, L.; Aceves-Mijares, M. [Electronics Department, INAOE, Apdo. 51, Puebla, Pue. 72000, México (Mexico); Cabañas-Tay, S. A.; Cardona-Castro, M. A.; Morales-Sánchez, A., E-mail: alfredo.morales@cimav.edu.mx [Centro de Investigación en Materiales Avanzados S.C., Unidad Monterrey-PIIT, Apodaca, NL 66628, México (Mexico); Domínguez-Horna, C. [Instituto de Microelectrónica de Barcelona, IMB-CNM (CSIC), Bellaterra 08193, Barcelona (Spain)

2016-07-18

Silicon nanocrystals (Si-ncs) are excellent candidates for the development of optoelectronic devices. Nevertheless, different strategies are still necessary to enhance their photo and electroluminescent properties by controlling their structural and compositional properties. In this work, the effect of the stoichiometry and structure on the optical properties of silicon rich oxide (SRO) films in a multilayered (ML) structure is studied. SRO MLs with silicon excess gradually increased towards the top and bottom and towards the center of the ML produced through the variation of the stoichiometry in each SRO layer were fabricated and confirmed by X-ray photoelectron spectroscopy. Si-ncs with three main sizes were observed by a transmission electron microscope, in agreement with the stoichiometric profile of each SRO layer. The presence of the three sized Si-ncs and some oxygen related defects enhances intense violet/blue and red photoluminescence (PL) bands. The SRO MLs were super-enriched with additional excess silicon by Si{sup +} implantation, which enhanced the PL intensity. Oxygen-related defects and small Si-ncs (<2 nm) are mostly generated during ion implantation enhancing the violet/blue band to become comparable to the red band. The structural, compositional, and luminescent characteristics of the multilayers are the result of the contribution of the individual characteristics of each layer.

White organic light-emitting devices based on blue fluorescent dye combined with dual sub-monolayer

Energy Technology Data Exchange (ETDEWEB)

Yang, Huishan, E-mail: yanghuishan1697@163.com

2013-10-15

White organic light-emitting devices have been realized by using highly blue fluorescent dye 4,4′-Bis(2,2-diphenyl-ethen-1-yl)-4,4′-di-(tert-butyl)phenyl(p-TDPVBi) and [2-methyl-6-[2-(2, 3,6,7-tetrahydro-1H, red fluorescent dye 5H-benzo[ij] quinolizin-9-yl) ethenyl]-4H-pyran-4-ylidene] propane-dinitrile(DCM2), together with well known green fluorescent dye quinacridone (QAD). The fabrication of multilayer WOLEDs did not involve the hard-to-control doping process. The structure of the device is ITO/m-MTDATA (45 nm)/NPB(8 nm)/p-TDPVBi(15 nm)/DCM2(x nm)/Alq{sub 3} (5 nm)/QAD(y nm)/Alq{sub 3}(55 nm)/LiF(1 nm)/Al, where 4,4′,4′′-tris{N,-(3-methylphenyl)-N-phenylamine}triphenylamine (m-MTDATA) acts as a hole injection layer, N,N′-bis-(1-naphthyl)-N, N′-diphenyl-1, 1′-biph-enyl-4, 4′-diamine (NPB) acts as a hole transport layer, p-TDPVBi acts as a blue emitting layer, DCM2 acts as a red emitting layer, QAD acts as a green emitting layer, tris-(8-hydroxyquinoline) aluminum (Alq{sub 3}) acts as an electron transport layer, and WOLEDs of devices A, B, C and D are different in layer thickness of DCM2 and QAD, respectively. To change the thickness of dual sub-monolayer DCM2 and QAD, the WOLEDs were obtained. When x, y=0.05, 0.1, the Commission Internationale de 1’Eclairage (CIE) coordinates of the device change from (0.4458, 0.4589) at 3 V to (0.3137, 0.3455) at 12 V that are well in the white region, and the color temperature and color rendering index were 5348 K and 85 at 8 V, respectively. Its maximum luminance was 35260 cd/m{sup 2} at 12 V, and maximum current efficiency and maximum power efficiency were 13.54 cd/A at 12 V and 6.68 lm/W at 5 V, respectively. Moreover, the current efficiency is largely insensitive to the applied voltage. The electroluminescence intensity of white EL devices varied only little at deferent dual sub-monolayer. Device D exhibited relatively high color rendering index (CRI) in the range of 88–90, which was essentially

Enhanced performance of light-emitting diodes based on a nanocomposite of dehydrated nanotube titanic acid and poly(vinylcarbazole) (PVK)

Energy Technology Data Exchange (ETDEWEB)

Qian, L. [Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China)]. E-mail: qian_lei@126.com; Yang, S.Y. [Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Jin, Z.S. [Key Laboratory on Special Functional Materials, Henan University, Kaifeng 475001 (China); Zhang, Z.J. [Key Laboratory on Special Functional Materials, Henan University, Kaifeng 475001 (China); Zhang, T. [Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Teng, F. [Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Xu, X.R. [Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China)

2005-01-31

Performance of light-emitting diodes (LEDs) based on a nanocomposite of dehydrated nanotube titanic acid (DNTA) and poly(vinylcarbazole) (PVK) as emissive layer, i.e., ITO/PVK:DNTA(2 wt%)(100 nm)/BCP(30 nm)/Alq{sub 3}(10 nm)/LiF(1 nm)/Al [device D{sub 2}], was reported. By investigation of the luminance and electric characteristics of the device, we found that the performance of device D{sub 2} was greatly improved. The recombination zone changed evidently due to the improvement of holes mobility. Compared with those devices without incorporating DNTA, both the maximum luminance and the electroluminescent efficiency of the device D{sub 2} can be improved by a factor of three. Furthermore, the turn-on voltage of the device decreased dramatically.

Modeling of transient electroluminescence overshoot in bilayer organic light-emitting diodes using rate equations

International Nuclear Information System (INIS)

Chandra, V.K.; Chandra, B.P.; Tiwari, M.; Baghel, R.N.; Ramrakhiani, M.

2012-01-01

When a voltage pulse is applied under forward biased condition to a spin-coated bilayer organic light-emitting diode (OLED), then initially the electroluminescence (EL) intensity appearing after a delay time, increases with time and later on it attains a saturation value. At the end of the voltage pulse, the EL intensity decreases with time, attains a minimum intensity and then it again increases with time, attains a peak value and later on it decreases with time. For the OLEDs, in which the lifetime of trapped carriers is less than the decay time of the EL occurring prior to the onset of overshoot, the EL overshoot begins just after the end of voltage pulse. The overshoot in spin-coated bilayer OLEDs is caused by the presence of an interfacial layer of finite thickness between hole and electron transporting layers in which both transport molecules coexist, whereby the interfacial energy barrier impedes both hole and electron passage. When a voltage pulse is applied to a bilayer OLED, positive and negative space charges are established at the opposite faces of the interfacial layer. Subsequently, the charge recombination occurs with the incoming flux of injected carriers of opposite polarity. When the voltage is turned off, the interfacial charges recombine under the action of their mutual electric field. Thus, after switching off the external voltage the electrons stored in the interface next to the anode cell compartment experience an electric field directed from cathode to anode, and therefore, the electrons move towards the cathode, that is, towards the positive space charge, whereby electron–hole recombination gives rise to luminescence. The EL prior to onset of overshoot is caused by the movement of electrons in the electron transporting states, however, the EL in the overshoot region is caused by the movement of detrapped electrons. On the basis of the rate equations for the detrapping and recombination of charge carriers accumulated at the interface

Modeling of transient electroluminescence overshoot in bilayer organic light-emitting diodes using rate equations

Energy Technology Data Exchange (ETDEWEB)

Chandra, V.K. [Department of Electrical and Electronics Engineering, Chhatrapati Shivaji Institute of Technology, Shivaji Nagar, Kolihapuri, Durg 491001 (C.G.) (India); Chandra, B.P., E-mail: bpchandra4@yahoo.co.in [Department of Applied Physics, Ashoka Institute of Technology and Management, Rajnandgaon 491441 (C.G.) (India); Tiwari, M. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (M.P.) (India); Baghel, R.N. [School of Studies in Physics and Astrophysics, Pt. Ravishankar Shukla University, Raipur 492010 (C.G.) (India); Ramrakhiani, M. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (M.P.) (India)

2012-06-15

When a voltage pulse is applied under forward biased condition to a spin-coated bilayer organic light-emitting diode (OLED), then initially the electroluminescence (EL) intensity appearing after a delay time, increases with time and later on it attains a saturation value. At the end of the voltage pulse, the EL intensity decreases with time, attains a minimum intensity and then it again increases with time, attains a peak value and later on it decreases with time. For the OLEDs, in which the lifetime of trapped carriers is less than the decay time of the EL occurring prior to the onset of overshoot, the EL overshoot begins just after the end of voltage pulse. The overshoot in spin-coated bilayer OLEDs is caused by the presence of an interfacial layer of finite thickness between hole and electron transporting layers in which both transport molecules coexist, whereby the interfacial energy barrier impedes both hole and electron passage. When a voltage pulse is applied to a bilayer OLED, positive and negative space charges are established at the opposite faces of the interfacial layer. Subsequently, the charge recombination occurs with the incoming flux of injected carriers of opposite polarity. When the voltage is turned off, the interfacial charges recombine under the action of their mutual electric field. Thus, after switching off the external voltage the electrons stored in the interface next to the anode cell compartment experience an electric field directed from cathode to anode, and therefore, the electrons move towards the cathode, that is, towards the positive space charge, whereby electron-hole recombination gives rise to luminescence. The EL prior to onset of overshoot is caused by the movement of electrons in the electron transporting states, however, the EL in the overshoot region is caused by the movement of detrapped electrons. On the basis of the rate equations for the detrapping and recombination of charge carriers accumulated at the interface

Direct Integration of Dynamic Emissive Displays into Knitted Fabric Structures

Science.gov (United States)

Bellingham, Alyssa

Smart textiles are revolutionizing the textile industry by combining technology into fabric to give clothing new abilities including communication, transformation, and energy conduction. The advent of electroluminescent fibers, which emit light in response to an applied electric field, has opened the door for fabric-integrated emissive displays in textiles. This thesis focuses on the development of a flexible and scalable emissive fabric display with individually addressable pixels disposed within a fabric matrix. The pixels are formed in areas where a fiber supporting the dielectric and phosphor layers of an electroluminescent structure contacts a conductive surface. This conductive surface can be an external conductive fiber, yarn or wire, or a translucent conductive material layer deposited at set points along the electroluminescent fibers. Different contacting methods are introduced and the different ways the EL yarns can be incorporated into the knitted fabric are discussed. EL fibers were fabricated using a single yarn coating system with a custom, adjustable 3D printed slot die coater for even distribution of material onto the supporting fiber substrates. These fibers are mechanically characterized inside of and outside of a knitted fabric matrix to determine their potential for various applications, including wearables. A 4-pixel dynamic emissive display prototype is fabricated and characterized. This is the first demonstration of an all-knit emissive display with individually controllable pixels. The prototype is composed of a grid of fibers supporting the dielectric and phosphor layers of an electroluminescent (EL) device structure, called EL fibers, and conductive fibers acting as the top electrode. This grid is integrated into a biaxial weft knit structure where the EL fibers make up the rows and conductive fibers make up the columns of the reinforcement yarns inside the supporting weft knit. The pixels exist as individual segments of

Carrier Injection and Transport in Blue Phosphorescent Organic Light-Emitting Device with Oxadiazole Host

Directory of Open Access Journals (Sweden)

Tien-Lung Chiu

2012-06-01

Full Text Available In this paper, we investigate the carrier injection and transport characteristics in iridium(IIIbis[4,6-(di-fluorophenyl-pyridinato-N,C2']picolinate (FIrpic doped phosphorescent organic light-emitting devices (OLEDs with oxadiazole (OXD as the bipolar host material of the emitting layer (EML. When doping Firpic inside the OXD, the driving voltage of OLEDs greatly decreases because FIrpic dopants facilitate electron injection and electron transport from the electron-transporting layer (ETL into the EML. With increasing dopant concentration, the recombination zone shifts toward the anode side, analyzed with electroluminescence (EL spectra. Besides, EL redshifts were also observed with increasing driving voltage, which means the electron mobility is more sensitive to the electric field than the hole mobility. To further investigate carrier injection and transport characteristics, FIrpic was intentionally undoped at different positions inside the EML. When FIrpic was undoped close to the ETL, driving voltage increased significantly which proves the dopant-assisted-electron-injection characteristic in this OLED. When the undoped layer is near the electron blocking layer, the driving voltage is only slightly increased, but the current efficiency is greatly reduced because the main recombination zone was undoped. However, non-negligible FIrpic emission is still observed which means the recombination zone penetrates inside the EML due to certain hole-transporting characteristics of the OXD.

Optical properties of white organic light-emitting devices fabricated utilizing a mixed CaAl12O19:Mn4+ and Y3Al5O12:Ce3+ color conversion layer.

Science.gov (United States)

Jeong, H S; Kim, S H; Lee, K S; Jeong, J M; Yoo, T W; Kwon, M S; Yoo, K H; Kim, T W

2013-06-01

White organic light-emitting devices (OLEDs) were fabricated by combining a blue OLED with a color conversion layer made of mixed Y3Al5O12:Ce3+ green and Ca2AlO19:Mn4+ red phosphors. The X-ray diffraction patterns showed that Ce3+ ions in the Y3Al5O12:Ce3+ phosphors completely substituted for the Y3+ ions and the Mn4+ ions in the CaAl12O19:Mn4+ phosphors completely substituted for the Ca2+ ions. Electroluminescence spectra at 11 V for the OLEDs fabricated utilizing a color conversion layer showed that the Commission Internationale de l'Eclairage coordinates for the Y3Al5O12:Ce3+ and CaAl12O19:Mn4+ phosphors mixed at the ratio of 1:5 and 1:10 were (0.31, 0.34) and (0.32, 0.37), respectively, indicative of a good white color.

Microscopic Perspective on Photovoltaic Reciprocity in Ultrathin Solar Cells.

Science.gov (United States)

Aeberhard, Urs; Rau, Uwe

2017-06-16

The photovoltaic reciprocity theory relates the electroluminescence spectrum of a solar cell under applied bias to the external photovoltaic quantum efficiency of the device as measured at short circuit conditions. Its derivation is based on detailed balance relations between local absorption and emission rates in optically isotropic media with nondegenerate quasiequilibrium carrier distributions. In many cases, the dependence of density and spatial variation of electronic and optical device states on the point of operation is modest and the reciprocity relation holds. In nanostructure-based photovoltaic devices exploiting confined modes, however, the underlying assumptions are no longer justifiable. In the case of ultrathin absorber solar cells, the modification of the electronic structure with applied bias is significant due to the large variation of the built-in field. Straightforward use of the external quantum efficiency as measured at short circuit conditions in the photovoltaic reciprocity theory thus fails to reproduce the electroluminescence spectrum at large forward bias voltage. This failure is demonstrated here by numerical simulation of both spectral quantities at normal incidence and emission for an ultrathin GaAs p-i-n solar cell using an advanced quantum kinetic formalism based on nonequilibrium Green's functions of coupled photons and charge carriers. While coinciding with the semiclassical relations under the conditions of their validity, the theory provides a consistent microscopic relationship between absorption, emission, and charge carrier transport in photovoltaic devices at arbitrary operating conditions and for any shape of optical and electronic density of states.

Effect of localization states on the electroluminescence spectral width of blue–green light emitting InGaN/GaN multiple quantum wells

Energy Technology Data Exchange (ETDEWEB)

Liu, Wei [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083, China and School of Electronic and Electrical Engineering, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Zhao, De Gang, E-mail: dgzhao@red.semi.ac.cn; Jiang, De Sheng; Chen, Ping; Liu, Zong Shun; Zhu, Jian Jun; Li, Xiang; Shi, Ming; Zhao, Dan Mei [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Liu, Jian Ping; Zhang, Shu Ming; Wang, Hui; Yang, Hui [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215125 (China)

2015-11-15

The electroluminescence (EL) spectra of blue–green light emitting InGaN/GaN multiple quantum well (MQW) structures grown via metal-organic chemical vapor deposition are investigated. With increasing In content in InGaN well layers, the peak energy redshifts, the emission intensity reduces and the inhomogeneous broadening of the luminescence band increases. In addition, it is found that the EL spectra shrink with increasing injection current at low excitation condition, which may be ascribed to both Coulomb screening of polarization field and carrier transferring from shallower localization states to the deeper ones, while at high currents the state-filling effect in all localization states may become significant and lead to a broadening of EL spectra. However, surprisingly, for the MQW sample with much higher In content, the EL spectral bandwidth can be almost unchanged with increasing current at the high current range, since a large number of carriers may be captured by the nonradiative recombination centers distributed outside the localized potential traps and the state-filling effect in the localization states is suppressed.

Effect of localization states on the electroluminescence spectral width of blue–green light emitting InGaN/GaN multiple quantum wells

International Nuclear Information System (INIS)

Liu, Wei; Zhao, De Gang; Jiang, De Sheng; Chen, Ping; Liu, Zong Shun; Zhu, Jian Jun; Li, Xiang; Shi, Ming; Zhao, Dan Mei; Liu, Jian Ping; Zhang, Shu Ming; Wang, Hui; Yang, Hui

2015-01-01

The electroluminescence (EL) spectra of blue–green light emitting InGaN/GaN multiple quantum well (MQW) structures grown via metal-organic chemical vapor deposition are investigated. With increasing In content in InGaN well layers, the peak energy redshifts, the emission intensity reduces and the inhomogeneous broadening of the luminescence band increases. In addition, it is found that the EL spectra shrink with increasing injection current at low excitation condition, which may be ascribed to both Coulomb screening of polarization field and carrier transferring from shallower localization states to the deeper ones, while at high currents the state-filling effect in all localization states may become significant and lead to a broadening of EL spectra. However, surprisingly, for the MQW sample with much higher In content, the EL spectral bandwidth can be almost unchanged with increasing current at the high current range, since a large number of carriers may be captured by the nonradiative recombination centers distributed outside the localized potential traps and the state-filling effect in the localization states is suppressed

Organic Light-Emitting Diodes with Magnesium Doped CuPc as an Efficient Electron Injection Layer

International Nuclear Information System (INIS)

Jun-Song, Cao; Min, Guan; Guo-Hua, Cao; Yi-Ping, Zeng; Jin-Min, Li; Da-Shan, Qin

2008-01-01

Bright organic electroluminescent devices are developed using a metal-doped organic layer intervening between the cathode and the emitting layer. The typical device structure is a glass substrate/indium-tin oxide (ITO)/copper phthalocyanine(CuPc)/N,N-bis-(1-naphthl)-diphenyl-1, 1'-biphenyl-4,4'-diamine (NPB)/Tris(8-quinolinolato) alu-minum(Alq 3 )/Mg-doped CuPc/Ag. At a driving voltage of 11 V, the device with a layer of Mg-doped CuPc (1:2 in weight) shows a brightness of 4312 cd/m 2 and a current efficiency of 2.52 cd/A, while the reference device exhibits 514 cd/m 2 and 1.25 cd/A

Near-intrinsic energy resolution for 30–662 keV gamma rays in a high pressure xenon electroluminescent TPC

International Nuclear Information System (INIS)

Álvarez, V.; Borges, F.I.G.M.; Cárcel, S.; Castel, J.; Cebrián, S.; Cervera, A.; Conde, C.A.N.; Dafni, T.; Dias, T.H.V.T.; Díaz, J.

2013-01-01

We present the design, data and results from the NEXT prototype for Double Beta and Dark Matter (NEXT-DBDM) detector, a high-pressure gaseous natural xenon electroluminescent time projection chamber (TPC) that was built at the Lawrence Berkeley National Laboratory. It is a prototype of the planned NEXT-100 136 Xe neutrino-less double beta decay (0νββ) experiment with the main objectives of demonstrating near-intrinsic energy resolution at energies up to 662 keV and of optimizing the NEXT-100 detector design and operating parameters. Energy resolutions of ∼1% FWHM for 662 keV gamma rays were obtained at 10 and 15 atm and ∼5% FWHM for 30 keV fluorescence xenon X-rays. These results demonstrate that 0.5% FWHM resolutions for the 2459 keV hypothetical neutrino-less double beta decay peak are realizable. This energy resolution is a factor 7–20 better than that of the current leading 0νββ experiments using liquid xenon and thus represents a significant advancement. We present also first results from a track imaging system consisting of 64 silicon photo-multipliers recently installed in NEXT–DBDM that, along with the excellent energy resolution, demonstrates the key functionalities required for the NEXT-100 0νββ search

Quantum-dot light-emitting diodes utilizing CdSe /ZnS nanocrystals embedded in TiO2 thin film

Science.gov (United States)

Kang, Seung-Hee; Kumar, Ch. Kiran; Lee, Zonghoon; Kim, Kyung-Hyun; Huh, Chul; Kim, Eui-Tae

2008-11-01

Quantum-dot (QD) light-emitting diodes (LEDs) are demonstrated on Si wafers by embedding core-shell CdSe /ZnS nanocrystals in TiO2 thin films via plasma-enhanced metallorganic chemical vapor deposition. The n-TiO2/QDs /p-Si LED devices show typical p-n diode current-voltage and efficient electroluminescence characteristics, which are critically affected by the removal of QD surface ligands. The TiO2/QDs /Si system we presented can offer promising Si-based optoelectronic and electronic device applications utilizing numerous nanocrystals synthesized by colloidal solution chemistry.

Quantum Dots and Their Multimodal Applications: A Review

Directory of Open Access Journals (Sweden)

Paul H. Holloway

2010-03-01

Full Text Available Semiconducting quantum dots, whose particle sizes are in the nanometer range, have very unusual properties. The quantum dots have band gaps that depend in a complicated fashion upon a number of factors, described in the article. Processing-structure-properties-performance relationships are reviewed for compound semiconducting quantum dots. Various methods for synthesizing these quantum dots are discussed, as well as their resulting properties. Quantum states and confinement of their excitons may shift their optical absorption and emission energies. Such effects are important for tuning their luminescence stimulated by photons (photoluminescence or electric field (electroluminescence. In this article, decoupling of quantum effects on excitation and emission are described, along with the use of quantum dots as sensitizers in phosphors. In addition, we reviewed the multimodal applications of quantum dots, including in electroluminescence device, solar cell and biological imaging.

Transparent Electrodes with Nanotubes and Graphene for Printed Optoelectronic Applications

Directory of Open Access Journals (Sweden)

Marcin Słoma

2014-01-01

Full Text Available We report here on printed electroluminescent structures containing transparent electrodes made of carbon nanotubes and graphene nanoplatelets. Screen-printing and spray-coating techniques were employed. Electrodes and structures were examined towards optical parameters using spectrophotometer and irradiation meter. Electromechanical properties of transparent electrodes are exterminated with cyclical bending test. Accelerated aging process was conducted according to EN 62137 standard for reliability tests of electronics. We observed significant negative influence of mechanical bending on sheet resistivity of ITO, while resistivity of nanotube and graphene based electrodes remained stable. Aging process has also negative influence on ITO based structures resulting in delamination of printed layers, while those based on carbon nanomaterials remained intact. We observe negligible changes in irradiation for structures with carbon nanotube electrodes after accelerated aging process. Such materials demonstrate a high application potential in general purpose electroluminescent devices.

Color-tunable and stable-efficiency white organic light-emitting diode fabricated with fluorescent-phosphorescent emission layers

International Nuclear Information System (INIS)

Yang, Su-Hua; Shih, Po-Jen; Wu, Wen-Jie; Huang, Yi-Hua

2013-01-01

White organic light emitting diodes (OLEDs) were fabricated for color-tunable lighting applications. Fluorescent and phosphorescent hybrid emission layers (EMLs) were used to enhance the luminance and stability of the devices, which have blue-EML/CBP interlayer/green-EML/phosphorescent-sensitized-EML/red-EML structures. The influence of the composition and structure of the EMLs on the electroluminescence properties of the devices were investigated from the viewpoint of their emission spectra. The possible exciton harvesting, diffusion, transport, and annihilation processes occurring in the EMLs were also evaluated. A maximum luminance intensity of 7400 cd/m 2 and a highly stable current efficiency of 3.2 cd/A were obtained. Good color tunability was achieved for the white OLEDs; the chromatic coordinates linearly shifted from pure white (0.300, 0.398) to cold white (0.261, 0.367) when the applied voltage was varied from 10 to 14 V. -- Highlights: • Exciton harvesting, diffusion, transport, and annihilation processes were evaluated. • The electroluminescence properties were investigated from the viewpoint of the emission spectra. • Good color tunability and stable-efficiency were achieved for the white OLEDs

Charge injection and accumulation in organic light-emitting diode with PEDOT:PSS anode

Energy Technology Data Exchange (ETDEWEB)

Weis, Martin, E-mail: martin.weis@stuba.sk [Institute of Electronics and Photonics, Slovak University of Technology, Ilkovičova 3, Bratislava 81219 (Slovakia); Otsuka, Takako; Taguchi, Dai; Manaka, Takaaki; Iwamoto, Mitsumasa, E-mail: iwamoto@ome.pe.titech.ac.jp [Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 O-okayama, Meguro-ku, Tokyo 152-8552 (Japan)

2015-04-21

Organic light-emitting diode (OLED) displays using flexible substrates have many attractive features. Since transparent conductive oxides do not fit the requirements of flexible devices, conductive polymer poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) has been proposed as an alternative. The charge injection and accumulation in OLED devices with PEDOT:PSS anodes are investigated and compared with indium tin oxide anode devices. Higher current density and electroluminescence light intensity are achieved for the OLED device with a PEDOT:PSS anode. The electric field induced second-harmonic generation technique is used for direct observation of temporal evolution of electric fields. It is clearly demonstrated that the improvement in the device performance of the OLED device with a PEDOT:PSS anode is associated with the smooth charge injection and accumulation.

White organic light-emitting devices with tunable color emission fabricated utilizing exciplex formation at heterointerfaces including m-MDATA

International Nuclear Information System (INIS)

Lee, Kwang Seop; Choo, Dong Chul; Kim, Tae Whan

2011-01-01

The electrical and the optical properties of organic light-emitting devices (OLEDs) fabricated utilizing a 4,4',4''-tris(2-methylphenyl-phenylamino)triphenylamine (m-MTDATA) were investigated to clarify the effect of exciplex on their color stabilization and color purity. The electrons combined with the holes at heterointerfaces between the m-MTDATA layer and the 9,10-di(2-naphthyl)anthracene (MADN) and the 4-(dicyanomethylene)-2-methyl-6-(p-dimethyl aminostyryl)-4H-pyran (DCM1) emitting layer (EML) resulted in the formation of the exciplex. The emission peak of the electroluminescence spectra for the OLEDs fabricated utilizing the m-MTDATA layer shifted to a lower energy side in comparison with that of the EML. This was due to the interaction of the holes in the m-MTDATA layer and the electrons in the MADN EML. Carriers in white OLEDs (WOLEDs) with exciplex emissions existed at the heterointerfaces between the m-MTDATA and the EML because the DCM1 EML was too thin to affect the EL peak related to the m-MTDATA layer. The Commission Internationale de l'Eclairage coordinates of WOLEDs at 9.5 V were (0.33, 0.36), and their maximum current efficiency at 46 mA/cm 2 was 2.03 cd/A.

White organic light-emitting devices with tunable color emission fabricated utilizing exciplex formation at heterointerfaces including m-MDATA

Energy Technology Data Exchange (ETDEWEB)

Lee, Kwang Seop; Choo, Dong Chul; Kim, Tae Whan, E-mail: twk@hanyang.ac.kr

2011-05-31

The electrical and the optical properties of organic light-emitting devices (OLEDs) fabricated utilizing a 4,4',4''-tris(2-methylphenyl-phenylamino)triphenylamine (m-MTDATA) were investigated to clarify the effect of exciplex on their color stabilization and color purity. The electrons combined with the holes at heterointerfaces between the m-MTDATA layer and the 9,10-di(2-naphthyl)anthracene (MADN) and the 4-(dicyanomethylene)-2-methyl-6-(p-dimethyl aminostyryl)-4H-pyran (DCM1) emitting layer (EML) resulted in the formation of the exciplex. The emission peak of the electroluminescence spectra for the OLEDs fabricated utilizing the m-MTDATA layer shifted to a lower energy side in comparison with that of the EML. This was due to the interaction of the holes in the m-MTDATA layer and the electrons in the MADN EML. Carriers in white OLEDs (WOLEDs) with exciplex emissions existed at the heterointerfaces between the m-MTDATA and the EML because the DCM1 EML was too thin to affect the EL peak related to the m-MTDATA layer. The Commission Internationale de l'Eclairage coordinates of WOLEDs at 9.5 V were (0.33, 0.36), and their maximum current efficiency at 46 mA/cm{sup 2} was 2.03 cd/A.

Changes induced in a ZnS:Cr-based electroluminescent waveguide structure by intrinsic near-infrared laser radiation

International Nuclear Information System (INIS)

Vlasenko, N. A.; Oleksenko, P. F.; Mukhlyo, M. A.; Veligura, L. I.

2013-01-01

The causes of changes that occur in a thin-film electroluminescent metal-insulator-semiconductor-insulator-metal waveguide structure based on ZnS:Cr (Cr concentration of ∼4 × 10 20 cm −3 ) upon lasing (λ ≈ 2.6 μm) and that induce lasing cessation are studied. It is established that lasing ceases because of light-scattering inhomogeneities formed in the structure and, hence, optical losses enhance. The origin of the inhomogeneities and the causes of their formation are clarified by studying the surface topology and the crystal structure of constituent layers of the samples before and after lasing. The studies are performed by means of atomic force microscopy and X-ray radiography. It is shown that a substantial increase in the sizes of grains on the surface of the structure is the manifestation of changes induced in the ZnS:Cr film by recrystallization. Recrystallization is initiated by local heating by absorbed laser radiation in existing Cr clusters and quickened by a strong electric field (>1 MV cm −1 ). The changes observed in the ZnS:Cr film are as follows: the textured growth of ZnS crystallites, an increase in the content of Cr clusters, and the appearance of some CrS and a rather high ZnO content. Some ways for improving the stability of lasing in the ZnS:Cr-based waveguide structures are proposed

Experiments on Printed Intelligence and Its Applications

OpenAIRE

Barbonelova, Angelina

2015-01-01

Printed intelligence technology refers to products and systems that are produced using traditional printing methods and that are able to communicate or react with the user, environment or other products and systems. The technology provides the foundations of innovative products such as printed OLEDs (organic light emitting device), electroluminescent displays, organic photovoltaics, thin film batteries and disposable sensors. This study presents research on different printing techniques i...

Nonlinear optical properties of Nd3+-Li+ co-doped ZnS-PVP thin films

Science.gov (United States)

Talwatkar, S. S.; Sunatkari, A. L.; Tamgadge, Y. S.; Muley, G. G.

2018-04-01

The nonlinear optical properties of Nd3+-Li+ co-doped ZnS-PVP nanocomposite were studied using a continuous wave (CW) He-Ne laser (λ = 632.8 nm)by z-scan technique. The nonlinear refractive index (n2), absorption coefficient (β) and third order nonlinear susceptibility (χ(3)) of PVP thin films embedded with Nd3+-Li+ co-doped ZnS NPs was found in the order of 10-7 cm2/W, 10-6 cm/W and 10-7 esu respectively. The nonlinearity found increasing with Nd3+-Li+ co-dopant concentration. Based on the results, it is proposed that this material is a new class of luminescent material suitable in optoelectronics devices application, especially in light-emitting devices, electroluminescent devices, display devices, etc.

Synthesis and characterization of 5,7-dimethyl-8-hydroxyquinoline and 2-(2-pyridyl)benzimidazole complexes of zinc(II) for optoelectronic application

Science.gov (United States)

Singh, Kapoor; Kumar, Amit; Srivastava, Ritu; Kadyan, Partap S.; Kamalasanan, Modeeparampil N.; Singh, Ishwar

2011-11-01

Bis(5,7-dimethyl-8-hydroxyquinolinato)zinc(II) (Me 2q) 2Zn and 5,7-dimethyl-8-hydroxyquinolinato(2-(2-pyridyl)benzimidazole) zinc(II) Me 2q(pbi)Zn have been synthesized and characterized by various techniques. These metal complexes have high thermal stability (>300 °C) and high glass transition temperatures (>150 °C). The vacuum deposited films of these materials show good film forming property and are suitable for opto-electronic applications. Multilayered organic electroluminescent (EL) devices have been fabricated having structure ITO/α-NPD/zinc complex/BCP/Alq 3/LiF/Al, which produce emission with chromaticity having Commission Internationale d'Eclairage (CIE) coordinates x = 0.506 and y = 0.484 for (Me 2q) 2Zn; x = 0.47 and y = 0.52 for (Me 2q)(pbi)Zn complex. The electroluminescence spectra show peak emission centered at 572 and 561 nm respectively for these materials.

Analysis of the current-voltage characteristics of polymer-based organic light-emitting diodes (OLEDs deposited by spin coating

Directory of Open Access Journals (Sweden)

Ricardo Vera

2010-04-01

Full Text Available Polymer-based organic light-emitting diodes (OLEDs with the structure ITO / PEDOT:PSS / MDMO-PPV / Metal were prepared by spincoating. It is known that electroluminescence of these devices is strongly dependent on the material used as cathode and on the depositionparameters of the polymer electroluminescent layer MDMO-PPV. Objective. In this work the effect of i the frequency of the spin coater(1000-8000 rpm, ii the concentration of the MDMO-PPV: Toluene solution, and iii the material used as cathode (Aluminium or Silveron the electrical response of the devices, was evaluated through current-voltage (I-V measurements. Materials and methods. PEDOT:PPSand MDMO-PPV organic layers were deposited by spin coating on ITO substrates, and the OLED structure was completed with cathodesof aluminium and silver. The electric response of the devices was evaluated based on the I-V characteristics. Results. Diodes prepared withthinner organic films allow higher currents at lower voltages; this can be achieved either by increasing the frequency of the spin coater orby using concentrations of MDMO-PPV: Toluene lower than 2% weight. A fit of the experimental data showed that the diodes have twocontributions to the current. The first one is attributed to parasitic currents between anode and cathode, and the other one is a parallel currentthrough the organic layer, in which the carrier injection mechanism is mediated by thermionic emission. Conclusions. The results of thefitting and the energy level alignment through the whole structure show that PPV-based OLEDs are unipolar devices, with current mainlyattributed to hole transport.

Protection device for a thermonuclear device

International Nuclear Information System (INIS)

Kawashima, Shuichi.

1986-01-01

Purpose: To exactly detect the void coefficients of coolants even under high magnetic fields thereby detect the overheat of a thermonuclear device at an early stage. Constitution: The protecting device of this invention comprises a laser beam generation device, a laser beam detection device and an accident detection device. The laser generation device always generates laser beams, which are permeated through coolants and detected by the laser beam detection device, the optical amount of which is transmitted to the accident detection device. The accident detection device judges the excess or insufficiency of the detected optical amount with respect to the optical amount of the laser beams under the stationary state as a reference and issues an accident signal. Since only the optical cables that do not undergo the effect of the magnetic fields are exposed to high magnetic fields in the protection device of this invention, a high reliability can be maintained. (Kamimura, M.)

Development of aluminum gallium nitride based optoelectronic devices operating in deep UV and terahertz spectrum ranges

Science.gov (United States)

Zhang, Wei

structure were fabricated into mesa-structure devices and the I-V characterization at 20 K indicates sequential tunneling with electroluminescence emission at about 10 THz. Similarly, Far-infrared photoconductive detectors were grown by the same method. Photocurrent spectra centered at 23 mum (13 THz) are resolved up to 50 K, with responsivity of approximately 7 mA/W.

Photovoltaic reciprocity and quasi-Fermi level splitting in nanostructure-based solar cells (Conference Presentation)

Science.gov (United States)

Aeberhard, Urs

2017-04-01

The photovoltaic reciprocity theory relates the electroluminescence spectrum of a solar cell under applied bias to the external photovoltaic quantum efficiency of the device as measured at short circuit conditions [1]. So far, the theory has been verified for a wide range of devices and material systems and forms the basis of a growing number of luminesecence imaging techniques used in the characterization of photovoltaic materials, cells and modules [2-5]. However, there are also some examples where the theory fails, such as in the case of amorphous silicon. In our contribution, we critically assess the assumptions made in the derivation of the theory and compare its predictions with rigorous formal relations as well as numerical computations in the framework of a comprehensive quantum-kinetic theory of photovoltaics [6] as applied to ultra-thin absorber architectures [7]. One of the main applications of the photovoltaic reciprocity relation is the determination of quasi-Fermi level splittings (QFLS) in solar cells from the measurement of luminescence. In nanostructure-based photovoltaic architectures, the determination of QFLS is challenging, but instrumental to assess the performance potential of the concepts. Here, we use our quasi-Fermi level-free theory to investigate existence and size of QFLS in quantum well and quantum dot solar cells. [1] Uwe Rau. Reciprocity relation between photovoltaic quantum efficiency and electrolumines- cent emission of solar cells. Phys. Rev. B, 76(8):085303, 2007. [2] Thomas Kirchartz and Uwe Rau. Electroluminescence analysis of high efficiency cu(in,ga)se2 solar cells. J. Appl. Phys., 102(10), 2007. [3] Thomas Kirchartz, Uwe Rau, Martin Hermle, Andreas W. Bett, Anke Helbig, and Jrgen H. Werner. Internal voltages in GaInP-GaInAs-Ge multijunction solar cells determined by electro- luminescence measurements. Appl. Phys. Lett., 92(12), 2008. [4] Thomas Kirchartz, Anke Helbig, Wilfried Reetz, Michael Reuter, Jürgen H. Werner, and

Tunable blue organic light emitting diode based on aluminum calixarene supramolecular complex

Science.gov (United States)

Legnani, C.; Reyes, R.; Cremona, M.; Bagatin, I. A.; Toma, H. E.

2004-07-01

In this letter, the results of supramolecular organic light emitting diodes using a calix[4] arene complex thin film as emitter and electron transporting layer are presented. The devices were grown onto glass substrates coated with indium-tin-oxide layer and aluminum thick (150nm) cathode. By applying a dc voltage between the device electrodes in forward bias condition, a blue light emission in the active area of the device was observed. It was found that the electroluminescent emission peak can be tuned between 470 and 510nm changing the applied voltage bias from 4.3 to 5.4V. The observed tunable emission can be associated with an energy transfer from the calixarene compound.

Device-Centric Monitoring for Mobile Device Management

Directory of Open Access Journals (Sweden)

Luke Chircop

2016-03-01

Full Text Available The ubiquity of computing devices has led to an increased need to ensure not only that the applications deployed on them are correct with respect to their specifications, but also that the devices are used in an appropriate manner, especially in situations where the device is provided by a party other than the actual user. Much work which has been done on runtime verification for mobile devices and operating systems is mostly application-centric, resulting in global, device-centric properties (e.g. the user may not send more than 100 messages per day across all applications being difficult or impossible to verify. In this paper we present a device-centric approach to runtime verify the device behaviour against a device policy with the different applications acting as independent components contributing to the overall behaviour of the device. We also present an implementation for Android devices, and evaluate it on a number of device-centric policies, reporting the empirical results obtained.

Singlet-to-triplet interconversion using hyperfine as well as ferromagnetic fringe fields.

Science.gov (United States)

Wohlgenannt, M; Flatté, M E; Harmon, N J; Wang, F; Kent, A D; Macià, F

2015-06-28

Until recently the important role that spin-physics ('spintronics') plays in organic light-emitting devices and photovoltaic cells was not sufficiently recognized. This attitude has begun to change. We review our recent work that shows that spatially rapidly varying local magnetic fields that may be present in the organic layer dramatically affect electronic transport properties and electroluminescence efficiency. Competition between spin-dynamics due to these spatially varying fields and an applied, spatially homogeneous magnetic field leads to large magnetoresistance, even at room temperature where the thermodynamic influences of the resulting nuclear and electronic Zeeman splittings are negligible. Spatially rapidly varying local magnetic fields are naturally present in many organic materials in the form of nuclear hyperfine fields, but we will also review a second method of controlling the electrical conductivity/electroluminescence, using the spatially varying magnetic fringe fields of a magnetically unsaturated ferromagnet. Fringe-field magnetoresistance has a magnitude of several per cent and is hysteretic and anisotropic. This new method of control is sensitive to even remanent magnetic states, leading to different conductivity/electroluminescence values in the absence of an applied field. We briefly review a model based on fringe-field-induced polaron-pair spin-dynamics that successfully describes several key features of the experimental fringe-field magnetoresistance and magnetoelectroluminescence. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

[Photovoltaic character of organic EL devices MEH-PPV/Alq3].

Science.gov (United States)

Lin, Peng; Liang, Chun-Jun; Deng, Zhen-Bo; Xiong, De-Ping; Wang, Li; Zhang, Zhi-Feng; Zhang, Xi-Qing

2005-01-01

An organic photovoltaic(PV) cell, ITO/MEH-PPV/Alq3/LiF/Al, was fabricated. The MEH-PPV and Alq3 are the electron-acceptor and donor in the cell, respectively. The respond region matchs the adsorption of Alq3 film. Under UV light with 0.5 mW x cm(-2), the cell shows a short-circuit current of 2.4 microA x cm(-2), open-circuit voltage of 2.6 V, a fill factor of 0.71, and a power conversion efficiency of 0.9%. It was found that the PV cell indicates electroluminescence (EL) performance and could emit orange light at DC voltage. The maximum luminance is about 1 000 cd x cm(-2) at 15 V.

Quantum mechanical modeling the emission pattern and polarization of nanoscale light emitting diodes.

Science.gov (United States)

Wang, Rulin; Zhang, Yu; Bi, Fuzhen; Frauenheim, Thomas; Chen, GuanHua; Yam, ChiYung

2016-07-21

Understanding of the electroluminescence (EL) mechanism in optoelectronic devices is imperative for further optimization of their efficiency and effectiveness. Here, a quantum mechanical approach is formulated for modeling the EL processes in nanoscale light emitting diodes (LED). Based on non-equilibrium Green's function quantum transport equations, interactions with the electromagnetic vacuum environment are included to describe electrically driven light emission in the devices. The presented framework is illustrated by numerical simulations of a silicon nanowire LED device. EL spectra of the nanowire device under different bias voltages are obtained and, more importantly, the radiation pattern and polarization of optical emission can be determined using the current approach. This work is an important step forward towards atomistic quantum mechanical modeling of the electrically induced optical response in nanoscale systems.

Enhancement of charge carrier recombination efficiency by utilizing a hole-blocking interlayer in white OLEDs

International Nuclear Information System (INIS)

Wang Qi; Yu Junsheng; Zhao Juan; Li Ming; Lu Zhiyun

2013-01-01

Charge carrier balance and recombination are essential factors relating to the performance of white organic light-emitting devices (WOLEDs). In this study, we discussed the contribution of charge carrier balance in the interlayer-based WOLEDs. By varying the interlayer thickness, the mechanisms of electroluminescent spectral alteration, energy transfer, and especially, charge carrier transport and balance in the devices were investigated and revealed in detail. With a 5 nm thick interlayer tailoring charge carrier transport and recombination, WOLEDs yielded a high power efficiency, current efficiency and external quantum efficiency of 36.1 lm W −1 , 47.1 cd A −1 and 18.3%, respectively. Additionally, single-carrier devices and quantitative analysis were subsequently carried out, demonstrating that the enhancement of carrier recombination efficiency corresponds to the optimization of device performance. (paper)

Plasmonic Perovskite Light-Emitting Diodes Based on the Ag-CsPbBr3 System.

Science.gov (United States)

Zhang, Xiaoli; Xu, Bing; Wang, Weigao; Liu, Sheng; Zheng, Yuanjin; Chen, Shuming; Wang, Kai; Sun, Xiao Wei

2017-02-08

The enhanced luminescence through semiconductor-metal interactions suggests the great potential of device performance improvement via properly tailored plasmonic nanostructures. Surface plasmon enhanced electroluminescence in an all-inorganic CsPbBr 3 perovskite light-emitting diode (LED) is fabricated by decorating the hole transport layer with the synthesized Ag nanorods. An increase of 42% and 43.3% in the luminance and efficiency is demonstrated for devices incorporated with Ag nanorods. The device with Ag introduction indicates identical optoelectronic properties to the controlled device without Ag nanostructures. The increased spontaneous emission rate caused by the Ag-induced plasmonic near-field effect is responsible for the performance enhancement. Therefore, the plasmonic Ag-CsPbBr 3 nanostructure studied here provides a novel strategy on the road to the future development of perovskite LEDs.

Synthesis and characterization of germane/stannane-capped polysiloles for the fabrication of luminescent OLED.

Science.gov (United States)

Kim, Myoung-Hee; Woo, Hee-Gweon; Kim, Whan Gi; Cho, Myong-Shik

2009-12-01

Dehydropolymerization (with various inorganic hydrides) and subsequent germane/stannane-capping (with Me2GeHCI and Ph2SnHCI) of 1,1-dihydrotetraphenylsilole (1) give electroluminescent germane/stannane-capped polysiloles (2) in high yield. The polymerization yield and molecular weight with Selectride increase in the order L-Selectride < N-Selectride < K-Selectride. The molecular weights increase in the order Red-Al < K-Selectride < Super Hydride. The germane/stannane-capped polysiloles 2 emit at 521 nm and are electroluminescent at 522 nm. The fluorescence quantum yield of 2 in toluene is (1.66 +/- 0.26) x 10(-2). The emission color is green and the maximum brightness of the device is 2,800 cd/m2 with a luminous efficiency of 0.68 lm/W. The type of end group exhibited no appreciable effect on the luminescent properties of polysilole backbone. Thus, the germane/stannane-capped polysiloles are found to be a good material for OLED fabrication.

OLED Fundamentals: Materials, Devices, and Processing of Organic Light-Emitting Diodes

Energy Technology Data Exchange (ETDEWEB)

Blochwitz-Nimoth, Jan; Bhandari, Abhinav; Boesch, Damien; Fincher, Curtis R.; Gaspar, Daniel J.; Gotthold, David W.; Greiner, Mark T.; Kido, Junji; Kondakov, Denis; Korotkov, Roman; Krylova, Valentina A.; Loeser, Falk; Lu, Min-Hao; Lu, Zheng-Hong; Lussem, Bjorn; Moro, Lorenza; Padmaperuma, Asanga B.; Polikarpov, Evgueni; Rostovtsev, Vsevolod V.; Sasabe, Hisahiro; Silverman, Gary; Thompson, Mark E.; Tietze, Max; Tyan, Yuan-Sheng; Weaver, Michael; Xin , Xu; Zeng, Xianghui

2015-05-26

What is an organic light emitting diode (OLED)? Why should we care? What are they made of? How are they made? What are the challenges in seeing these devices enter the marketplace in various applications? These are the questions we hope to answer in this book, at a level suitable for knowledgeable non-experts, graduate students and scientists and engineers working in the field who want to understand the broader context of their work. At the most basic level, an OLED is a promising new technology composed of some organic material sandwiched between two electrodes. When current is passed through the device, light is emitted. The stack of layers can be very thin and has many variations, including flexible and/or transparent. The organic material can be polymeric or composed small molecules, and may include inorganic components. The electrodes may consist of metals, metal oxides, carbon nanomaterials, or other species, though of course for light to be emitted, one electrode must be transparent. OLEDs may be fabricated on glass, metal foils, or polymer sheets (though polymeric substrates must be modified to protect the organic material from moisture or oxygen). In any event, the organic material must be protected from moisture during storage and operation. A control circuit, the exact nature of which depends on the application, drives the OLED. Nevertheless, the control circuit should have very stable current control to generate uniform light emission. OLEDs can be designed to emit a single color of light, white light, or even tunable colors. The devices can be switched on and off very rapidly, which makes them suitable for displays or for general lighting. Given the amazing complexity of the technical and design challenges for practical OLED applications, it is not surprising that applications are still somewhat limited. Although organic electroluminescence is more than 50 years old, the modern OLED field is really only about half that age – with the first high

Purely organic thermally activated delayed fluorescence (TADF) materials for organic light-emitting diodes (OLEDs)

OpenAIRE

Wong, Michael Y.; Zysman-Colman, Eli

2017-01-01

We thank the University of St Andrews for support. EZ-C thanks the Leverhulme Trust for financial support (RPG-2016-047). and the EPSRC (EP/P010482/1) for financial support. The design of thermally activated delayed fluorescence (TADF) materials both as emitters and as hosts is an exploding area of research. The replacement of phosphorescent metal complexes with inexpensive organic compounds in electroluminescent (EL) devices that demonstrate comparable performance metrics is paradigm shif...

Power source device for thermonuclear device

International Nuclear Information System (INIS)

Ozaki, Akira.

1992-01-01

The present invention provides a small sized and economical power source device for a thermonuclear device. That is, the device comprises a conversion device having a rated power determined by a power required during a plasma current excitation period and a conversion device having a rated power determined by a power required during a plasma current maintaining period, connected in series to each other. Then, for the former conversion device, power is supplied from an electric power generator and, for the latter, power is supplied from a power system. With such a constitution, during the plasma electric current maintaining period for substantially continuous operation, it is possible to conduct bypassing paired operation for the former conversion device while the electric power generator is put under no load. Further, since a short period rated power may be suffice for the former conversion device and the electric power generator having the great rated power required for the plasma electric current excitation period, they can be reduced in the size and made economical. On the other hand, since the power required for the plasma current maintaining period is relatively small, the capacity of the continuous rated conversion device may be small, and the power can be received from the power system. (I.S.)

Anomalous temperature dependent magneto-conductance in organic light-emitting diodes with multiple emissive states

Science.gov (United States)

Zhao, Chen-xiao; Jia, Wei-yao; Huang, Ke-Xun; Zhang, Qiao-ming; Yang, Xiao-hui; Xiong, Zu-hong

2015-07-01

The temperature dependence of the magneto-conductance (MC) in organic electron donor-acceptor hybrid and layer heterojunction diodes was studied. The MC value increased with temperature in layer heterojunction and in 10 wt. % hybrid devices. An anomalous decrease of the MC with temperature was observed in 25 wt. %-50 wt. % hybrid devices. Further increasing donor concentration to 75 wt. %, the MC again increased with temperature. The endothermic exciplex-exciton energy transfer and the change in electroplex/exciton ratio caused by change in charge transport with temperature may account for these phenomena. Comparative studies of the temperature evolutions of the IV curves and the electroluminescence and photoluminescence spectra back our hypothesis.

Device-Centric Monitoring for Mobile Device Management

OpenAIRE

Chircop, Luke; Colombo, Christian; Pace, Gordon J.

2016-01-01

The ubiquity of computing devices has led to an increased need to ensure not only that the applications deployed on them are correct with respect to their specifications, but also that the devices are used in an appropriate manner, especially in situations where the device is provided by a party other than the actual user. Much work which has been done on runtime verification for mobile devices and operating systems is mostly application-centric, resulting in global, device-centri...

P-GaN/ZnO nanorod heterojunction LEDs—effect of carrier concentration in p-GaN

Science.gov (United States)

Ng, A. M. C.; Chen, X. Y.; Fang, F.; Djurišić, A. B.; Chan, W. K.; Cheah, K. W.

2011-12-01

We studied the effect of carrier concentration in p-GaN substrate on the performance of p-GaN/n-ZnO nanorod heterojunction LEDs. ZnO nanorods were electrodeposited on commercial p-GaN wafers in a two electrode system from aqueous solutions of zinc nitrate and hexamethylenetetramine. The morphology and optical properties of ZnO nanorods were studied using photoluminescence and electron microscopy, and the LED device performance was studied by electroluminescence (EL) and I-V measurements.

Multilayered phosphorescent polymer light-emitting diodes using a solution-processed n-doped electron transport layer

Energy Technology Data Exchange (ETDEWEB)

Chen, Yuehua; Zhang, Mengke [Key Laboratory for Organic Electronics and Information Displays & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing University of Posts & Telecommunications, Nanjing 210023 (China); Zhang, Xinwen, E-mail: iamxwzhang@njupt.edu.cn [Key Laboratory for Organic Electronics and Information Displays & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing University of Posts & Telecommunications, Nanjing 210023 (China); Lei, Zhenfeng; Zhang, Xiaolin; Hao, Lin; Fan, Quli [Key Laboratory for Organic Electronics and Information Displays & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing University of Posts & Telecommunications, Nanjing 210023 (China); Lai, Wenyong, E-mail: iamwylai@njupt.edu.cn [Key Laboratory for Organic Electronics and Information Displays & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing University of Posts & Telecommunications, Nanjing 210023 (China); Huang, Wei [Key Laboratory for Organic Electronics and Information Displays & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing University of Posts & Telecommunications, Nanjing 210023 (China); Key Laboratory of Flexible Electronics & Institute of Advanced Materials, Jiangsu National Synergetic Innovation Center for Advanced Materials, Nanjing Tech University, Nanjing 211816 (China)

2017-06-15

Efficient multilayered green phosphorescent polymer light-emitting devices (PhPLEDs) were successfully fabricated using a solution-processed n-doped small molecular electron transporting layer (ETL) composed of 1,3,5-tris(N-phenyl-benzimidazol-2-yl)-benzene (TPBi) and CsF. We found that the electroluminescence properties of the devices with n-doped ETLs are significantly improved. The maximum luminance efficiency of the device with 7.5 wt% CsF doped TPBi ETL reached 26.9 cd/A, which is 1.5 times as large as that of the undoped device. The impedance spectra of the devices and electron transport properties of the CsF doped ETLs demonstrate that doping dramatically decreases the impedance and enhances the electrical conductivity. Similarly, enhanced performance of PhPLED is also observed by use of CsF-doped 4,7-diphenyl-1,10 -phenanthroline (BPhen) ETL. These results demonstrate that CsF can be used as an effective n-dopant in solution-processed devices.

Multilayered phosphorescent polymer light-emitting diodes using a solution-processed n-doped electron transport layer

International Nuclear Information System (INIS)

Chen, Yuehua; Zhang, Mengke; Zhang, Xinwen; Lei, Zhenfeng; Zhang, Xiaolin; Hao, Lin; Fan, Quli; Lai, Wenyong; Huang, Wei

2017-01-01

Efficient multilayered green phosphorescent polymer light-emitting devices (PhPLEDs) were successfully fabricated using a solution-processed n-doped small molecular electron transporting layer (ETL) composed of 1,3,5-tris(N-phenyl-benzimidazol-2-yl)-benzene (TPBi) and CsF. We found that the electroluminescence properties of the devices with n-doped ETLs are significantly improved. The maximum luminance efficiency of the device with 7.5 wt% CsF doped TPBi ETL reached 26.9 cd/A, which is 1.5 times as large as that of the undoped device. The impedance spectra of the devices and electron transport properties of the CsF doped ETLs demonstrate that doping dramatically decreases the impedance and enhances the electrical conductivity. Similarly, enhanced performance of PhPLED is also observed by use of CsF-doped 4,7-diphenyl-1,10 -phenanthroline (BPhen) ETL. These results demonstrate that CsF can be used as an effective n-dopant in solution-processed devices.