A simulation toolkit for electroluminescence assessment in rare event experiments

CERN Document Server

Oliveira, C A B; Veenhof, R; Biagi, S; Monteiro, C M B; Santos, J M F dos; Ferreira, A L; Veloso, J F C A

2011-01-01

A good understanding of electroluminescence is a prerequisite when optimising double-phase noble gas detectors for Dark Matter searches and high-pressure xenon TPCs for neutrinoless double beta decay detection. A simulation toolkit for calculating the emission of light through electron impact on neon, argon, krypton and xenon has been developed using the Magboltz and Garfield programs. Calculated excitation and electroluminescence efficiencies, electroluminescence yield and associated statistical fluctuations are presented as a function of electric field. Good agreement with experiment and with Monte Carlo simulations has been obtained.

The synthesis and study of new electroluminescent materials

International Nuclear Information System (INIS)

Pillow, J.

1998-01-01

Dendrimers offer many potential advantages over other organic electroluminescent materials that have been developed for use in light emitting diodes. This thesis describes the preparation of new electroluminescent dendrimers that consist of a luminescent core, charge-transporting stilbene dendrons and solubilising t-butyl surface groups. Choosing the core to have a longer conjugation length than the dendrons establishes an energy gradient that ensures that light emission occurs from the dendrimer core. Two convergent syntheses were developed for the preparation of dendrons that had aldehyde, bromide and styryl focal groups. The Heck reaction between styrene focused dendrons and 3,5-dibromoaryls was used to increase the dendron generation. This reaction was then alternated with the Wittig or Stille reactions in an iterative cycle to prepare dendrons of up to the third generation. The luminescent cores were chosen to be 1,4-distyrylbenzene, 1,4-distyrylanthracene and meso-tetraaryl porphyrin to emit blue, green and red light respectively. Dendrimers up to the third generation were prepared containing these cores. Further control over the emission colour was demonstrated by the chelation of metals into the porphyrin core. Computer modelling was used to predict the conformations of the dendrimers, with confirmation provided by GPC and X-ray crystallography. The modelled structures were then used to interpret the photoluminescence and electroluminescence spectra. Electrochemical analyses allowed the comparison of the HOMO and LUMO energy levels with the Fermi levels of the metal electrodes, which was used to explain the behaviour of the dendrimers in single layer light-emitting diodes. (author)

Comparison of electroluminescence intensity and photocurrent of polymer based solar cells

Energy Technology Data Exchange (ETDEWEB)

Hoyer, Ulrich; Swonke, Thomas; Auer, Richard [Bayerisches Zentrum fuer Angewandte Energieforschung e.V., Erlangen (Germany); Pinna, Luigi; Brabec, Christoph J. [Bayerisches Zentrum fuer Angewandte Energieforschung e.V., Erlangen (Germany); I-MEET, University Erlangen (Germany); Stubhan, Tobias; Li, Ning [I-MEET, University Erlangen (Germany)

2011-11-15

The reciprocity theorem for solar cell predicts a linear relation between electroluminescence emission and photovoltaic quantum efficiency and an exponential dependence of the electroluminescence signal on the applied voltage. Both dependencies are experimentally verified for polymer based solar cells in this paper. Furthermore it is shown, that electroluminescence imaging of organic solar cells has the potential to visualize the photocurrent distribution significantly faster than standard laser beam induced current mapping (LBIC) techniques. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A New Kind of Blue Hybrid Electroluminescent Device.

Science.gov (United States)

Wang, Junling; Li, Zhuan; Liu, Chunmei

2016-04-01

Bright blue Electroluminescence come from a ITO/BBOT doped silica (6 x 10(-3) M) made by a sol-gel method/Al driven by AC with 500 Hz at different voltages and Gaussian analysis under 55 V showed that blue emission coincidenced with typical triple emission from BBOT. This kind of device take advantage of organics (BBOT) and inorganics (silica). Electroluminescence from a single-layered sandwiched device consisting of blue fluorescent dye 2,5-bis (5-tert-butyl-2-benzoxazolyl) thiophene (BBOT) doped silica made by sol-gel method was investigated. A number of concentrations of hybrid devices were prepared and the maxium concentration was 6 x 10(-3) M. Blue electroluminescent (EL) always occurred above a threshold field 8.57 x 10(5) V/cm (30 V) at alternating voltage at 500 HZ. The luminance of the devices increased with the concentration of doped BBOT, but electroluminescence characteristics were different from a single molecule's photoluminescence properties of triple peaks. When analyzing in detail direct-current electroluminescence devices of pure BBOT, a single peak centered at 2.82 eV appeared with the driven voltage increase, which is similar to the hybrid devices. Comparing Gaussian decomposition date between two kinds of devices, the triple peak characteristic of BBOT was consistent. It is inferred that BBOT contributed EL of the hybrid devices mainly and silica may account for a very small part. Meanwhile the thermal stability of matrix silica was measured by Thermal Gravity-Mass Spectroscopy (TG-MS). There is 12 percent weight loss from room temperature to 1000 °C and silica has about 95% transmittance. So the matric silica played an important role in thermal stability and optical stability for BBOT. In addition, this kind of blue electroluminescence device can take advantages of organic materials BBOT and inorganic materials silica. This is a promising way to enrich EL devices, especially enriching inorganic EL color at a low cost.

Hybrid electroluminescent device based on MEH-PPV and ZnO

Energy Technology Data Exchange (ETDEWEB)

Hewidy, Dina; Gadallah, A.-S.; Fattah, G. Abdel

2017-02-15

Hybrid organic/inorganic electroluminescent device based on the structure of glass/ITO/PEDOT:PSS/MEH-PPV/ZnO/ZnO submicrorods/Al has been manufactured. Spin coating has been used to deposit both PEDOT:PSS and MEH-PPV. Two-step process has been used to synthesis ZnO submicrorods, namely, spin coating and chemical bath deposition. Changing the dimensions of the ZnO submicrorods in this layer structure has been investigated to improve the performance of the organic/inorganic electroluminescence device. Such layer structure provides electroluminescence with narrow emission bands due to a high gain with this structure. X-ray diffraction patterns and scanning electron microscope images show that ZnO submicrorods have hexagon structure. Current-voltage curve for the structure has been reported. Electroluminescence curves (electroluminescence intensity versus wavelength) at different bias voltages have been presented and these results show narrowing in full width at half maximum in the spectra at high current density compared to photoluminescence excitation. The narrowing in the spectrum has been explained. - Highlights: • Manufacturing of MEH-PPV and ZnO electroluminescent device has been reported. • Spin coating and chemical bath deposition have been used for preparation of ZnO. • SEM images and X-ray diffraction of ZnO have been presented. • Current-voltage curves and electroluminescent measurements have been reported.

Room-temperature low-voltage electroluminescence in amorphous carbon nitride thin films

Science.gov (United States)

Reyes, R.; Legnani, C.; Ribeiro Pinto, P. M.; Cremona, M.; de Araújo, P. J. G.; Achete, C. A.

2003-06-01

White-blue electroluminescent emission with a voltage bias less than 10 V was achieved in rf sputter-deposited amorphous carbon nitride (a-CN) and amorphous silicon carbon nitride (a-SiCN) thin-film-based devices. The heterojunction structures of these devices consist of: Indium tin oxide (ITO), used as a transparent anode; amorphous carbon film as an emission layer, and aluminum as a cathode. The thickness of the carbon films was about 250 Å. In all of the produced diodes, a stable visible emission peaked around 475 nm is observed at room temperature and the emission intensity increases with the current density. For an applied voltage of 14 V, the luminance was about 3 mCd/m2. The electroluminescent properties of the two devices are discussed and compared.

Green–white electroluminescence and green photoluminescence of zinc complexes

Energy Technology Data Exchange (ETDEWEB)

Janghouri, Mohammad; Mohajerani, Ezeddin [Laser and Plasma Research Institute, Shahid Beheshti University, G.C., Tehran 1983963113 (Iran, Islamic Republic of); Amini, Mostafa M.; Najafi, Ezzatollah [Department of Chemistry, Shahid Beheshti University, G.C., Tehran 1983963113 (Iran, Islamic Republic of)

2014-10-15

A series of zinc complexes has been synthesized and utilized as fluorescent materials in organic light-emitting diodes (OLEDs). All prepared complexes were characterized by elemental analysis (CHN), UV–vis, FT-IR and {sup 1}H NMR spectroscopy. The energy levels of zinc complexes were determined by cyclic voltammetry measurements. Devices with fundamental structure of ITO/PVK:PBD (50 nm)/zinc complexes/BCP (5 nm)/Alq{sub 3} (25 nm)/Al (180 nm) were fabricated. A green electroluminescence was obtained from thin film complexes at 25 nm thickness. When thickness of the complex bis(2-methylquinolin-8-olato)-bis[(acetato)-(methanol)zinc(II)] (B) in thin film decreased from 25 nm to 20, 18, and 12 nm, a white electroluminescence obtained. The white emission which was composed of blue and green attributed to the PVK:PBD blend and thickness of complex, respectively. With 12 nm thickness of complex, a maximum luminance of 4530 cd/m{sup 2} at a current density 398.32 mA/cm{sup 2} with CIE coordinates of 0.22 and 0.36 at 20 V was achieved. - Highlights: • Several new zinc complexes have been synthesized and utilized as fluorescent materials in OLEDs. • Photoluminescence emission of zinc complexes showed a red shift in respect to PVK:PBD blend. • Green electroluminescence emission from zinc complexes was achieved. • White emission has been obtained for an OLED by changing thickness of the zinc complex.

Green–white electroluminescence and green photoluminescence of zinc complexes

International Nuclear Information System (INIS)

Janghouri, Mohammad; Mohajerani, Ezeddin; Amini, Mostafa M.; Najafi, Ezzatollah

2014-01-01

A series of zinc complexes has been synthesized and utilized as fluorescent materials in organic light-emitting diodes (OLEDs). All prepared complexes were characterized by elemental analysis (CHN), UV–vis, FT-IR and 1 H NMR spectroscopy. The energy levels of zinc complexes were determined by cyclic voltammetry measurements. Devices with fundamental structure of ITO/PVK:PBD (50 nm)/zinc complexes/BCP (5 nm)/Alq 3 (25 nm)/Al (180 nm) were fabricated. A green electroluminescence was obtained from thin film complexes at 25 nm thickness. When thickness of the complex bis(2-methylquinolin-8-olato)-bis[(acetato)-(methanol)zinc(II)] (B) in thin film decreased from 25 nm to 20, 18, and 12 nm, a white electroluminescence obtained. The white emission which was composed of blue and green attributed to the PVK:PBD blend and thickness of complex, respectively. With 12 nm thickness of complex, a maximum luminance of 4530 cd/m 2 at a current density 398.32 mA/cm 2 with CIE coordinates of 0.22 and 0.36 at 20 V was achieved. - Highlights: • Several new zinc complexes have been synthesized and utilized as fluorescent materials in OLEDs. • Photoluminescence emission of zinc complexes showed a red shift in respect to PVK:PBD blend. • Green electroluminescence emission from zinc complexes was achieved. • White emission has been obtained for an OLED by changing thickness of the zinc complex

Phosphorescent rhenium emitters based on two electron-withdrawing diamine ligands: Structure, characterization and electroluminescent performance

Energy Technology Data Exchange (ETDEWEB)

Rui, Mei, E-mail: meirui2015@163.com [College of Science, Hebei North University, Zhangjiakou 075000, Hebei (China); Yuhong, Wang [College of Science, Hebei North University, Zhangjiakou 075000, Hebei (China); Yinting, Wang; Na, Zhang [Communication Training Base of The Headquarters of The General Staff, Zhangjiakou 075100, Hebei (China)

2014-09-15

In this paper, two diamine ligands having electron-withdrawing oxadiazole group and their corresponding Re(I) complexes were synthesized. Their geometric structure, electronic transition, photophysical property, thermal stability and electrochemical property were discussed in detail. Experimental data suggested that both complexes were promising yellow emitters with suited energy levels and good thermal stability for electroluminescent application. The correlation between emission performance and electron-withdrawing group was analyzed. It was found that electron-withdrawing group favored emission performance improvement. Their electroluminescence performance was also explored. Yellow electroluminescence was observed with maximum brightness of 1743 cd/m{sup 2}. - Highlights: • Oxadiazole derived diamine ligands and their Re(I) complexes were synthesized. • Their characters and properties were analyzed and compared in detail. • Electron-withdrawing group was proved to be positive for PL improvement. • Electroluminescence was obtained with maximum brightness of 1743 cd/m{sup 2}.

Ultraviolet electroluminescence from Au/MgO/MgxZn1−xO heterojunction diodes and the observation of Zn-rich cluster emission

International Nuclear Information System (INIS)

Liu, C.Y.; Xu, H.Y.; Sun, Y.; Zhang, C.; Ma, J.G.; Liu, Y.C.

2014-01-01

In this work, ultraviolet (UV) electroluminescence (EL) is achieved from Au/MgO/Mg x Zn 1−x O heterojunction diodes. The EL mechanism and laser forming process are discussed based on the energy band diagram, impact-ionization process and disordered optical structure. For ZnO and low Mg-content MgZnO devices, their EL spectra show single near-band-edge (NBE) emission. While in high Mg-content MgZnO devices, the emission from self-formed Zn-rich MgZnO clusters is observed and also contribute to the UV EL band. These Zn-rich clusters can act as thermally-stable luminescence centers, suggesting a promising route for developing MgZnO-based UV light-emitting devices. -- Highlights: • A series of Au/MgO/Mg x Zn 1−x O heterojunction diodes with multiple Mg compositions are fabricated and ultraviolet electroluminescence is achieved. • EL mechanism and laser forming process are discussed based on energy band diagram, impact-ionization process and disordered optical structure. • The transition from spontaneous to stimulated emission is observed in these heterojunctions, and the lasing mode is random laser. • In high Mg-content MgZnO devices, the emission from self-formed Zn-rich clusters is observed, which are thermally stable luminescence centers

Bias-polarity-dependent UV/visible transferable electroluminescence from ZnO nanorod array LED with graphene oxide electrode supporting layer

Science.gov (United States)

Liu, Weizhen; Wang, Wei; Xu, Haiyang; Li, Xinghua; Yang, Liu; Ma, Jiangang; Liu, Yichun

2015-09-01

A simple top electrode preparation process, employing continuous graphene oxide films as electrode supporting layers, was adopted to fabricate a ZnO nanorod array/p-GaN heterojunction LED. The achieved LED demonstrated different electroluminescence behaviors under forward and reverse biases: a yellow-red emission band was observed under forward bias, whereas a blue-UV emission peak was obtained under reverse bias. Electroluminescence spectra under different currents and temperatures, as well as heterojunction energy-band alignments, reveal that the yellow-red emission under forward bias originates from recombinations related to heterointerface defects, whereas the blue-UV electroluminescence under reverse bias is ascribed to transitions from near-band-edge and Mg-acceptor levels in p-GaN.

Organic Electroluminescent Sensor for Pressure Measurement

Directory of Open Access Journals (Sweden)

Tomohide Niimi

2012-10-01

Full Text Available We have proposed a novel concept of a pressure sensor called electroluminescent pressure sensor (ELPS based on oxygen quenching of electroluminescence. The sensor was fabricated as an organic light-emitting device (OLED with phosphorescent dyes whose phosphorescence can be quenched by oxygenmolecules, and with a polymer electrode which permeates oxygen molecules. The sensor was a single-layer OLED with Platinum (II octaethylporphine (PtOEP doped into poly(vinylcarbazole (PVK as an oxygen sensitive emissive layer and poly(3,4-ethylenedioxythiophene mixed with poly(styrenesulfonate (PEDOT:PSS as an oxygen permeating polymer anode. The pressure sensitivity of the fabricated ELPS sample was equivalent to that of the sensor excited by an illumination light source. Moreover, the pressure sensitivity of the sensor is equivalent to that of conventional pressure-sensitive paint (PSP, which is an optical pressure sensor based on photoluminescence.

Electroluminescent devices based on rare-earth tetrakis β-diketonate complexes

International Nuclear Information System (INIS)

Quirino, W.G.; Legnani, C.; Santos, R.M.B. dos; Teixeira, K.C.; Cremona, M.; Guedes, M.A.; Brito, H.F.

2008-01-01

In this paper the synthesis, photoluminescence and electroluminescence investigation of the novel tetrakis β-diketonate of rare-earth complexes such as, M[Eu(dbm) 4 ] and M[Tb(acac) 4 ] with a variety of cationic ligands, M = Li + , Na + and K + have been investigated. The emission spectra of the Eu 3+ and Tb 3+ complexes displayed characteristic narrow bands arising from intraconfigurational transitions of trivalent rare-earth ions and exhibited red color emission for the Eu 3+ ion ( 5 D 0 → 7 F J , J = 0-6) and green for the Tb 3+ ion ( 5 D 4 → 7 F J , J = 6-0). The lack of the broaden emission bands arising from the ligands suggests the efficient intramolecular energy transfer from the dbm and acac ligands to Eu 3+ and Tb 3+ ions, respectively. In accordance to the expected, the values of PL quantum efficiency (η) of the emitting 5 D 0 state of the tetrakis(β-diketonate) complexes of Eu 3+ were higher compared with those tris-complexes. Therefore, organic electroluminescent (EL) devices were fabricated with the structure as follows: indium tin oxide (ITO)/hole transport layer (HTL) NPB or MTCD/emitter layer M[RE(β-diketonate) 4 ] complexes)/Aluminum (Al). All the films were deposited by thermal evaporation carried out in a high vacuum environment system. The OLED light emission was independent of driving voltage, indicating that the combination of charge carriers generates excitons within the M[RE(β-diketonate) 4 ] layers, and the energy is efficiently transferred to RE 3+ ion. As a best result, a pure red and green electroluminescent emission was observed from the Eu 3+ and Tb 3+ devices, confirmed by (X,Y) color coordinates

Tunneling electron induced molecular electroluminescence from individual porphyrin J-aggregates

Energy Technology Data Exchange (ETDEWEB)

Meng, Qiushi; Zhang, Chao; Zhang, Yang, E-mail: zhyangnano@ustc.edu.cn, E-mail: zcdong@ustc.edu.cn; Zhang, Yao; Liao, Yuan; Dong, Zhenchao, E-mail: zhyangnano@ustc.edu.cn, E-mail: zcdong@ustc.edu.cn [Hefei National Laboratory for Physical Sciences at the Microscale and Synergetic Innovation Center of Quantum Information and Quantum Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2015-07-27

We investigate molecular electroluminescence from individual tubular porphyrin J-aggregates on Au(111) by tunneling electron excitations in an ultrahigh-vacuum scanning tunneling microscope (STM). High-resolution STM images suggest a spiral tubular structure for the porphyrin J-aggregate with highly ordered “brickwork”-like arrangements. Such aggregated nanotube is found to behave like a self-decoupled molecular architecture and shows red-shifted electroluminescence characteristics of J-aggregates originated from the delocalized excitons. The positions of the emission peaks are found to shift slightly depending on the excitation sites, which, together with the changes in the observed spectral profiles with vibronic progressions, suggest a limited exciton coherence number within several molecules. The J-aggregate electroluminescence is also found unipolar, occurring only at negative sample voltages, which is presumably related to the junction asymmetry in the context of molecular excitations via the carrier injection mechanism.

Correlation of AlGaN/GaN high-electron-mobility transistors electroluminescence characteristics with current collapse

Science.gov (United States)

Ohi, Shintaro; Yamazaki, Taisei; Asubar, Joel T.; Tokuda, Hirokuni; Kuzuhara, Masaaki

2018-02-01

We report on the correlation between the electroluminescence and current collapse of AlGaN/GaN high-electron-mobility transistors (HEMTs). Standard passivated devices suffering from severe current collapse exhibited high-intensity whitish electroluminescence confined near the drain contact. In contrast, devices with reduced current collapse resulting from oxygen plasma treatment or GaN capping showed low-intensity reddish emission across the entire gate-drain access region. A qualitative explanation of this observed correlation between the current collapse and electroluminescence is presented. Our results demonstrate that electroluminescence analysis is a powerful tool not only for identifying high-field regions but also for assessing the degree of current collapse in AlGaN/GaN HEMTs.

Electroluminescence of Zn{sub 2}GeO{sub 4}:Mn through SiC whisker electric field enhancement

Energy Technology Data Exchange (ETDEWEB)

Wagstaff, Brandon, E-mail: wagstabj@mcmaster.ca [McMaster University, Department of Engineering Physics, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada); Kitai, Adrian, E-mail: kitaia@mcmaster.ca [McMaster University, Department of Engineering Physics, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada); McMaster University, Department of Materials Science and Engineering, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4L8 (Canada)

2015-11-15

Alternating current (AC) electroluminescence of thin film oxide phosphors is well known. However in this work electroluminescence of bulk oxide powder phosphors is achieved. A new type of AC Electroluminescent (ACEL) device has been created and developed by integrating SiC whiskers into a phosphor matrix composed of manganese-activated zinc germanate (Zn{sub 2}GeO{sub 4}:Mn{sup 2+}). The conductive SiC whiskers enhance the average electric field in specific regions of the phosphor such that localized breakdown of the phosphor occurs, thus emitting green light. This field enhancement allows light emission to occur in thick film oxide powder phosphors and is notably the first time that bright and reasonably efficient electroluminescence of zinc germanate has been observed without using expensive thin film deposition techniques. Light emission has been achieved in thick pressed pellets using surface-deposited electrodes and the brightness-voltage characteristics of light emission are shown to be consistent with field emission of carriers from the embedded whiskers. - Highlights: • A new electroluminescent phosphor, Zn{sub 2}GeO{sub 4}Mn{sup 2+}+SiC whiskers, is proposed. • A procedure is described to fabricate a solid sample of this composite material. • Under an AC voltage, green light is emitted only in samples containing the SiC whiskers. • A brightness of 25 Cd/m{sup 2} and efficiency of 0.25 Lm/W is observed 9.6×10{sup 6} V/m. • This is notably the first time that ACEL has been observed in bulk Zn{sub 2}GeO{sub 4}Mn{sup 2+}.

Electroluminescence from a diamond device with ion-beam-micromachined buried graphitic electrodes

Energy Technology Data Exchange (ETDEWEB)

Forneris, J., E-mail: jacopo.forneris@unito.it [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Battiato, A.; Gatto Monticone, D. [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Picollo, F. [Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy); Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Amato, G.; Boarino, L.; Brida, G.; Degiovanni, I.P.; Enrico, E.; Genovese, M.; Moreva, E.; Traina, P. [Istituto Nazionale di Ricerca Metrologica (INRiM), Torino (Italy); Verona, C.; Verona Rinati, G. [Department of Industrial Engineering, University of Roma “Tor Vergata”, Roma (Italy); Olivero, P. [Physics Department and NIS Interdepartmental Centre, University of Torino, Torino (Italy); Istituto Nazionale di Fisica Nucleare (INFN), Sez. Torino, Torino (Italy); Consorzio Nazionale Interuniversitario per le Scienze Fisiche della Materia (CNISM), Sez. Torino, Torino (Italy)

2015-04-01

Focused MeV ion microbeams are suitable tools for the direct writing of conductive graphitic channels buried in an insulating diamond bulk, as demonstrated in previous works with the fabrication of multi-electrode ionizing radiation detectors and cellular biosensors. In this work we investigate the suitability of the fabrication method for the electrical excitation of color centers in diamond. Differently from photoluminescence, electroluminescence requires an electrical current flowing through the diamond sub-gap states for the excitation of the color centers. With this purpose, buried graphitic electrodes with a spacing of 10 μm were fabricated in the bulk of a detector-grade CVD single-crystal diamond sample using a scanning 1.8 MeV He{sup +} micro-beam. The current flowing in the gap region between the electrodes upon the application of a 450 V bias voltage was exploited as the excitation pump for the electroluminescence of different types of color centers localized in the above-mentioned gap. The bright light emission was spatially mapped using a confocal optical microscopy setup. The spectral analysis of electroluminescence revealed the emission from neutrally-charged nitrogen-vacancy centers (NV{sup 0}, λ{sub ZPL} = 575 nm), as well as from cluster crystal dislocations (A-band, λ = 400–500 nm). Moreover, an electroluminescence signal with appealing spectral features (sharp emission at room temperature, low phonon sidebands) from He-related defects was detected (λ{sub ZPL} = 536.3 nm, λ{sub ZPL} = 560.5 nm); a low and broad peak around λ = 740 nm was also observed and tentatively ascribed to Si-V or GR1 centers. These results pose interesting future perspectives for the fabrication of electrically-stimulated single-photon emitters in diamond for applications in quantum optics and quantum cryptography.

Organic solution-processible electroluminescent molecular glasses for non-doped standard red OLEDs with electrically stable chromaticity

Energy Technology Data Exchange (ETDEWEB)

Bi, Xiaoman; Zuo, Weiwei; Liu, Yingliang, E-mail: liuylxn@sohu.com; Zhang, Zhenru; Zeng, Cen; Xu, Shengang; Cao, Shaokui, E-mail: caoshaokui@zzu.edu.cn

2015-10-15

Highlights: • The D–A–D electroluminescent molecular glasses are synthesized. • Non-doped red electroluminescent film is fabricated by spin-coating. • Red OLED shows stable wavelength, luminous efficiency and chromaticity. • CIE1931 coordinate is in accord with standard red light in PAL system. - Abstract: Organic light-emitting molecular glasses (OEMGs) are synthesized through the introduction of nonplanar donor and branched aliphatic chain into electroluminescent emitters. The target OEMGs are characterized by {sup 1}H NMR, {sup 13}C NMR, IR, UV–vis and fluorescent spectra as well as elemental analysis, TG and DSC. The results indicated that the optical, electrochemical and electroluminescent properties of OEMGs are adjusted successfully by the replacement of electron-donating group. The non-doped OLED device with a standard red electroluminescent emission is achieved by spin-coating the THF solution of OEMG with a triphenylamine moiety. This non-doped red OLED device takes on an electrically stable electroluminescent performance, including the stable maximum electroluminescent wavelength of 640 nm, the stable luminous efficiency of 2.4 cd/A and the stable CIE1931 coordinate of (x, y) = (0.64, 0.35), which is basically in accord with the CIE1931 coordinate (x, y) = (0.64, 0.33) of standard red light in PAL system.

Observation of near infrared and enhanced visible emissions from electroluminescent devices with organo samarium(III) complex

Energy Technology Data Exchange (ETDEWEB)

Chu, B [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, W L [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Hong, Z R [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Zang, F X [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wei, H Z [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wang, D Y [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, M T [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Lee, C S [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, S T [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)

2006-11-07

Samarium (dibenzoylmethanato){sub 3} bathophenanthroline (Sm(DBM){sub 3} bath) was employed as an emitting and electron transport layer in organic light emitting diodes (OLEDs), and narrow electroluminescent (EL) emissions of a Sm{sup 3+} ion were observed in the visible and near infrared (NIR) region, differing from those of the same devices with Eu{sup 3+}- or Tb{sup 3+}-complex EL devices with the same structure. The EL emissions of the Sm{sup 3+}-devices originate from transitions from {sup 4}G{sub 5/2} to the lower respective levels of Sm{sup 3+} ions. A maximum luminance of 490 cd m{sup -2} at 15 V and an EL efficiency of 0.6% at 0.17 mA cm{sup -2} were obtained in the visible region, and the improved efficiency should be attributed to introducing a transitional layer between the N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-diphenyl-4,4'-diamine (TPD) film and the Sm(DBM){sub 3} bath film and the avoidance of interfacial exciplex emission in devices. Sharp emissions of Sm{sup 3+} ions in the NIR region were also observed under a lower threshold value less than 4.5 V.

Electroluminescent properties of an electrochemically cross-linkable carbazole peripheral poly(benzyl ether) dendrimer.

Science.gov (United States)

Park, Jin Young; Kim, Dong-Eun; Ponnapati, Ramakrishna; Kim, Jong-Min; Kwon, Young-Soo; Advincula, Rigoberto C

2011-04-04

The electroluminescent (EL) properties of a cross-linkable carbazole-terminated poly(benzyl ether) dendrimer, G(3)-cbz DN, doped into a PVK:PBD host matrix with a double-layer device configuration are investigated. Different concentrations of the guest material can control device efficiency, related to chromaticity of white emission and the origin of excited-state complexes occurring between hole-transporting carbazole units (PVK or G(3)-cbz DN) and electron-transporting oxadiazole (PBD). Two excited states (exciplex and electroplex) generated at the interfaces of PVK/G(3)-cbz DN and PBD result in competitive emission, exhibiting a broad band in the EL spectra. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The surface defect-related electroluminescence from the ZnO microwire

Energy Technology Data Exchange (ETDEWEB)

Ding Meng; Zhao Dongxu; Yao Bin; Li Binghui; Zhang Zhenzhong; Shan Chongxin; Shen Dezhen, E-mail: dxzhao2000@yahoo.com.cn [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130021 (China)

2011-02-23

Surface defect-related electroluminescence (EL) was realized from a single ZnO microwire-based metal-semiconductor-metal structure on a glass substrate. ZnO microwires were successfully fabricated using a simple chemical vapour deposition approach. Schottky contacts were detected between Au electrodes and the ZnO microwire. The EL spectrum showed a broad emission band covering the visible range from 400 to 700 nm. The possible EL emission mechanism is discussed in detail in this paper.

Unusual near-white electroluminescence of light emitting diodes based on saddle-shaped porphyrins.

Science.gov (United States)

Shahroosvand, Hashem; Zakavi, Saeed; Sousaraei, Ahmad; Mohajerani, Ezeddin; Mahmoudi, Malek

2015-05-14

In contrast to the red electroluminescence emission frequently observed in porphyrins based OLED devices, the present devices exhibit a nearly white emission with greenish yellow, yellowish green and blue green hues in the case of Fe(II)(TCPPBr6) (TCPPBr6 = β-hexabromo-meso-tetrakis-(4-phenyl carboxyl) porphyrinato), Zn(II)(TPPBr6) and Co(II)(TPPBr6), respectively.

Modelling electroluminescence in liquid argon

International Nuclear Information System (INIS)

Stewart, D Y; Barker, G J; Bennieston, A J; Harrison, P F; McConkey, N; Morgan, B; Ramachers, Y A; Lightfoot, P K; Robinson, M; Spooner, N J C; Thompson, L

2010-01-01

We present Monte-Carlo simulations of electron transport through liquid argon motivated by our recent observation of electroluminescence light emanating from a thick gaseous electron multiplier (THGEM) in a liquid argon volume. All known elastic and inelastic reaction cross-sections have been accounted for, providing electroluminescence light yield predictions for arbitrary electrostatic fields. This study concludes that the large field gradients needed to produce electroluminescence cannot be accounted for by straightforward electrostatic field calculations based on ideal THGEM holes, suggesting that further experimental investigations are required.

Silicon nanowire hot carrier electroluminescence

Energy Technology Data Exchange (ETDEWEB)

Plessis, M. du, E-mail: monuko@up.ac.za; Joubert, T.-H.

2016-08-31

Avalanche electroluminescence from silicon pn junctions has been known for many years. However, the internal quantum efficiencies of these devices are quite low due to the indirect band gap nature of the semiconductor material. In this study we have used reach-through biasing and SOI (silicon-on-insulator) thin film structures to improve the internal power efficiency and the external light extraction efficiency. Both continuous silicon thin film pn junctions and parallel nanowire pn junctions were manufactured using a custom SOI technology. The pn junctions are operated in the reach-through mode of operation, thus increasing the average electric field within the fully depleted region. Experimental results of the emission spectrum indicate that the most dominant photon generating mechanism is due to intraband hot carrier relaxation processes. It was found that the SOI nanowire light source external power efficiency is at least an order of magnitude better than the comparable bulk CMOS (Complementary Metal Oxide Semiconductor) light source. - Highlights: • We investigate effect of electric field on silicon avalanche electroluminescence. • With reach-through pn junctions the current and carrier densities are kept constant. • Higher electric fields increase short wavelength radiation. • Higher electric fields decrease long wavelength radiation. • The effect of the electric field indicates intraband transitions as main mechanism.

The effect of complexation with platinum in polyfluorene derivatives: A photo- and electro-luminescence study

International Nuclear Information System (INIS)

Assaka, Andressa M.; Hu Bin; Mays, Jimmy; Iamazaki, Eduardo T.; Atvars, Teresa D.Z.; Akcelrud, Leni

2011-01-01

The synthesis and characterization of a polymeric structure containing fluorene units statistically linked to 3-cyclohexyl-thiophene and bipyridine PFOTBipy-poly[(4-hexylthiophene-2,5-diyl)(9,9-dihexyl-fluoren-2,7-diyl) -co-(bipyridine-5.5'-diyl)(9,9-dihexyl-fluoren-2,7-diyl)], is reported. The complexation with platinum was possible through the bipyridil units present in 10%, 50% and 100% content. The structure has a fluorenyl moiety between each bipyridine and thiophene groups resulting in a stable and efficient light-emitting polymeric material combining the well known emissive properties of fluorene, the charge mobility generated by thiophene and the electron-transfer properties of a metal complex as well. All the polymers were photo and electroluminescent materials, and showed phosphorescence at low temperatures. Photoluminescence properties were studied by steady state and time resolved spectroscopy and showed changes of both emission peak and relative intensity of the emission bands depending on the relative amount of the platinum complex. The electroluminescence followed the trends found for photoluminescence. The blue emission of the copolymer without platinum is due to the fluorenyl segments and for higher complex contents the emission is characteristic of the aggregates involving the bipyridinyl moieties. Therefore, emission color can be tuned by the complex content. The turn-on voltage was strongly reduced from 22 to 8 V for the 100% complexed copolymer, as compared to the device made with the non complexed one, but the luminance decreased, due to quenching or trapping effects. - Research Highlights: →Statistic copolymer containing fluorine, thiophene and bipyridine. →Complexation of platinum with platinum with bipyridine. →Electroluminescence and electrophosphorescence at low temperatures. →Emission color can be tuned by the complex content.

AC Electroluminescent Processes in Pr3+-Activated (Ba0.4Ca0.6TiO3 Diphase Polycrystals

Directory of Open Access Journals (Sweden)

Nan Gao

2017-05-01

Full Text Available We investigated the properties of alternating current (AC-driven electroluminescence from (Ba0.4Ca0.6TiO3:Pr3+ diphase polycrystal-based device. The results of crystal phases and micrographs, and the symmetrical dual emissions in one AC cycle, indicate the spontaneous formation of a dielectric/phosphor/dielectric sandwich microstructure in (Ba0.4Ca0.6TiO3:Pr3+. The electroluminescent device emits a red light of 617 nm, which is attributed to the 1D2-3H4 transition of Pr3+ in the phosphor phase. At a fixed AC frequency, the intensity of electroluminescence exhibits a steep enhancement when applying an increased driving electric field that is beyond a threshold. In a fixed driving electric field, the intensity of electroluminescence shows a rapid rise at low frequencies, but reaches saturation at high frequencies. Based on a double-injection model, we discussed systematically the electroluminescent processes in a whole cycle of AC electric field, which matched well with the experimental data. Our investigation is expected to expand our understanding of such a diphase electroluminescent device, thereby promoting their applications in lighting and displays.

Electroluminescence light emitting diodes - an environmental friendly approach

International Nuclear Information System (INIS)

Shaukat, S.F.; Farooq, R.

2005-01-01

The simple porous silicon-based devices producing stable electroluminescence (EL) by the deposition of a poly-4-dicyanomethylene-4H-cyclopenta dithiophene monolayer (PCDM) into the nanostructure was reported. The structure of these devices is Au/PCDM/porous silicon/Si/Al. The EL emission is bright, visible by the naked eye under normal daylight and broad in wavelength covering the whole visible range with a peak at 60 nm. The emission area of the devices is 1 cm/sup 2/. The El starting voltage is in the range of 14-30 V and the current is around 300 mA. The time stability was good for all the devices tested. After exposure to the air for more than three months, the devices show nearly the same emission intensity without increase of external power supplied. (author)

Polymer matrix electroluminescent materials and devices

Science.gov (United States)

Marrocco, III, Matthew L.; Motamedi, Farshad J [Claremont, CA; Abdelrazzaq, Feras Bashir [Covina, CA; Abdelrazzaq, legal representative, Bashir Twfiq

2012-06-26

Photoluminescent and electroluminescent compositions are provided which comprise a matrix comprising aromatic repeat units covalently coordinated to a phosphorescent or luminescent metal ion or metal ion complexes. Methods for producing such compositions, and the electroluminescent devices formed therefrom, are also disclosed.

Electroluminescence dependence on the organic thickness in ZnO nano rods/Alq3 heterostructure devices.

Science.gov (United States)

Kan, Pengzhi; Wang, Yongsheng; Zhao, Suling; Xu, Zheng; Wang, Dawei

2011-04-01

ZnO nanorods are synthesised by a hydrothermal method on ITO glass. Their crystallization and morphology are detected by XRD and SEM, respectively. The results show that the ZnO nanorod array has grown primarily along a direction aligned perpendicular to the ITO substrate. The average height and diameter of the nanorods is about 130 nm and 30 nm, respectively. Then ZnO nano rods/Alq3 heterostructure LEDs are prepared by thermal evaporation of Alq3 molecules. The thicknesses of the Alq3 layers are 130 nm, 150 nm, 170 nm and 190 nm, respectively. The electroluminescence of the devices is detected under different DC bias voltages. The exciton emission of Alq3 is detected in all devices. When the thickness of Alq3 is 130 nm, the UV electroluminescence of ZnO is around 382 nm, and defect emissions around 670 nm and 740 nm are detected. Defect emissions of ZnO nanorods are prominent. When the thickness of Alq3 increases to over 170 nm, it is difficult to observe defect emissions from the ZnO nano rods. In such devices, the exciton emission of Alq3 is more prominent than other emissions under different bias voltage.

Electroluminescence from single-wall carbon nanotube network transistors.

Science.gov (United States)

Adam, E; Aguirre, C M; Marty, L; St-Antoine, B C; Meunier, F; Desjardins, P; Ménard, D; Martel, R

2008-08-01

The electroluminescence (EL) properties from single-wall carbon nanotube network field-effect transistors (NNFETs) and small bundle carbon nanotube field effect transistors (CNFETs) are studied using spectroscopy and imaging in the near-infrared (NIR). At room temperature, NNFETs produce broad (approximately 180 meV) and structured NIR spectra, while they are narrower (approximately 80 meV) for CNFETs. EL emission from NNFETs is located in the vicinity of the minority carrier injecting contact (drain) and the spectrum of the emission is red shifted with respect to the corresponding absorption spectrum. A phenomenological model based on a Fermi-Dirac distribution of carriers in the nanotube network reproduces the spectral features observed. This work supports bipolar (electron-hole) current recombination as the main mechanism of emission and highlights the drastic influence of carrier distribution on the optoelectronic properties of carbon nanotube films.

Exciplex formation and electroluminescent absorption in ultraviolet organic light-emitting diodes

International Nuclear Information System (INIS)

Zhang Qi; Zhang Hao; Xu Tao; Wei Bin; Zhang Xiao-Wen

2015-01-01

We investigated the formation of exciplex and electroluminescent absorption in ultraviolet organic light-emitting diodes (UV OLEDs) using different heterojunction structures. It is found that an energy barrier of over 0.3 eV between the emissive layer (EML) and adjacent transport layer facilitates exciplex formation. The electron blocking layer effectively confines electrons in the EML, which contributes to pure UV emission and enhances efficiency. The change in EML thickness generates tunable UV emission from 376 nm to 406 nm. In addition, the UV emission excites low-energy organic function layers and produces photoluminescent emission. In UV OLED, avoiding the exciplex formation and averting light absorption can effectively improve the purity and efficiency. A maximum external quantum efficiency of 1.2% with a UV emission peak of 376 nm is realized. (paper)

Photo and electroluminescence of porous silicon layers

International Nuclear Information System (INIS)

Keshmini, S.H.; Samadpour, S.; Haji-Ali, E.; Rokn-Abadi, M.R.

1995-01-01

Porous silicon (PSi) layers were prepared by both chemical and electrochemical methods on n- and p-type Si substrates. In the former technique, light emission was obtained from p-type and n-type samples. It was found that intense light illumination during the preparation process was essential for PSi formation on n-type substrates. An efficient electrochemical cell with some useful features was designed for electrochemical etching of silicon. Various preparation parameters were studied and photoluminescence emissions ranging from dark red to light blue were obtained from PSi samples prepared on p-type substrates. N-type samples produced emission ranging from dark red to orange yellow. Electroluminescence of porous silicon samples showed that the color of the emission was the same as the photoluminescence color of the sample, and its intensity and duration depended on the current density passed through the sample. The effects of exposure of samples to air, storage in vacuum and heat treatment in air on luminescence intensity of the samples and preparation of patterned porous layers were also studied. (author)

Time-of-flight Measurement Of Hole-tunneling Properties And Emission Color Control In Organic Light-emitting Diodes

Science.gov (United States)

Kurata, K.; Kashiwabara, K.; Nakajima, K.; Mizoguchi, Y.; Ohtani, N.

2011-12-01

Hole transport properties of organic light-emitting diodes (OLEDs) with a thin hole-blocking layer (HBL) were evaluated by time-of-flight measurement. Electroluminescence (EL) spectra of OLEDs with various HBL thicknesses were also evaluated. The results clearly show that the time-resolved photocurrent response and the emission color strongly depend on HBL thickness. This can be attributed to hole-tunneling through the thin HBL. We successfully fabricated a white OLED by controlling the thickness of HBL.

Effect of the polymer emission on the electroluminescence characteristics of n-ZnO nanorods/p-polymer hybrid light emitting diode

Science.gov (United States)

Zaman, S.; Zainelabdin, A.; Amin, G.; Nur, O.; Willander, M.

2011-09-01

Hybrid light emitting diodes (LEDs) based on zinc oxide (ZnO) nanorods and polymers (single and blended) were fabricated and characterized. The ZnO nanorods were grown by the chemical bath deposition method at 50°C. Three different LEDs, with blue emitting, orange-red emitting or their blended polymer together with ZnO nanorods, were fabricated and studied. The current-voltage characteristics show good diode behavior with an ideality factor in the range of 2.1 to 2.27 for all three devices. The electroluminescence spectrum (EL) of the blended device has an emission range from 450 nm to 750 nm, due to the intermixing of the blue emission generated by poly(9,9-dioctylfluorene) denoted as PFO with orange-red emission produced by poly(2-methoxy-5(20-ethyl-hexyloxy)-1,4-phenylenevinylene) 1,4-phenylenevinylene) symbolized as MEH PPV combined with the deep-band emission (DBE) of the ZnO nanorods, i.e. it covers the whole visible region and is manifested as white light. The CIE color coordinates showed bluish, orange-red and white emission from the PFO, MEH PPV and blended LEDs with ZnO nanorods, respectively. These results indicate that the choice of the polymer with proper concentration is critical to the emitted color in ZnO nanorods/p-organic polymer LEDs and careful design should be considered to obtain intrinsic white light sources.

Photoluminescence and electroluminescence of a tripodal compound containing 7-diethylamino-coumarin moiety

Energy Technology Data Exchange (ETDEWEB)

Yu Tianzhi; Zhang Peng; Zhang Hui; Meng Jing; Fan Duowang [Key Laboratory of Opto-Electronic Technology and Intelligent Control (Lanzhou Jiaotong University), Ministry of Education, Lanzhou 730070 (China); Zhao Yuling; Dong Wenkui [School of Chemical and Biological Engineering, Lanzhou Jiaotong University, Lanzhou 730070 (China)], E-mail: ytz823@hotmail.com

2008-12-07

A novel tripodal compound, tris[2-(7-diethylamino-coumarin-3-carboxamide)ethyl]amine (Tren-C), was synthesized and characterized by elemental analysis, infrared and {sup 1}H-NMR spectra. The photoluminescent (PL) and electroluminescent properties of Tren-C were investigated. Tren-C exhibits different colour emissions in solid states and solutions. The electroluminescence devices comprising vacuum vapour-deposited films using the compound as a dopant were fabricated, showing blue emissions that are identical to its PL spectrum in chloroform solutions. With the device structure of indium tin oxide (ITO)/4, 4', 4''-tris-N-naphthyl-N-phenylamino-triphenylamine (2-TNATA) (5 nm)/N, N'-bis-(naphthyl)-N, N'-diphenyl-1, 1'-biphenyl-4, 4'-diamine (NPB) (40 nm)/4, 4'-bis(9-carbazolyl) biphenyl (CBP) : Tren-C (0.5 wt%, 30 nm)/2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1, 3, 4-oxadiazole (Bu-PBD) (30 nm)/LiF (1 nm)/Al (100 nm), a maximum external quantum efficiency of 2.85%, a maximum luminous efficiency of 3.85 cd A{sup -1} and a maximum luminance of 1450 cd m{sup -2} are realized.

[The role of BCP in electroluminescence of multilayer organic light-emitting devices].

Science.gov (United States)

Deng, Zhao-Ru; Yang, Sheng-Yi; Lou, Zhi-Dong; Meng, Ling-Chuan

2009-03-01

As a hole-blocking layer, 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) is usually used in blue and white light electroluminescent devices. The ability of blocking holes of BCP layer depends on its thickness, and basically holes can tunnel through thin BCP layer. In order to know the role of BCP layer in electroluminescence (EL) of multilayer organic light-emitting diodes (OLEDs), in the present paper, the authors designed a multilayer OLED ITO/NPB/BCP/Alq3 : DCJTB/Alq3/Al and investigated the influence of thickness of BCP on the EL spectra of multilayer OLEDs at different applied voltages. The experimental data show that thin BCP layer can block holes partially and tune the energy transfer between different emissive layers, and in this way, it is easy to obtain white emission, but its EL spectra will change with the applied voltages. The EL spectra of multilayer device will remain relatively stable when BCP layer is thick enough, and the holes can hardly tunnel through when the thickness of BCP layer is more than 15 nm. Furthermore, the stability of EL spectra of the multilayer OLED at different applied voltages was discussed.

Fabrication and performance of ACTFEL display devices using manganese-doped zinc germanate as a green-emitting electroluminescent layer

International Nuclear Information System (INIS)

Kim, Joo Han; Yoon, Kyung Ho

2010-01-01

Alternating-current thin-film electroluminescent (ACTFEL) display devices fabricated using manganese-doped zinc germanate (Zn 2 GeO 4 :Mn) as a green-emitting electroluminescent layer material are described. The ACTFEL display devices were fabricated with a standard bottom emission structure having a multilayer stack of thin films in the metal/semiconductor/insulator/ metal (MSIM) configuration. The device was constructed on a transparent Corning glass substrate through which the emitted EL light passed. The Zn 2 GeO 4 :Mn emission layer was synthesized by using a RF magnetron sputter deposition method, followed by post-annealing at 700 .deg. C in air ambient for 1 hour. The obtained Zn 2 GeO 4 :Mn films were found to be polycrystalline with a rhombohedral crystal structure. A green emission spectrum with a maximum at approximately 538 nm was produced from the fabricated device. The chromaticity color coordinates of the EL emission were measured to be x = 0.308 and y = 0.657. The device demonstrated a sharp increase in the intensity of green EL emission upon increasing the AC peak voltage applied to the device above a threshold of 148 V.

Exciplex electroluminescence and photoluminescence spectra of the new organic materials based on zinc complexes of sulphanylamino-substituted ligands.

Science.gov (United States)

Kaplunov, Mikhail G; Krasnikova, Svetlana S; Nikitenko, Sergey L; Sermakasheva, Natalia L; Yakushchenko, Igor K

2012-04-03

We have investigated the electroluminescence spectra of the electroluminescent devices based on the new zinc complexes of amino-substituted benzothiazoles and quinolines containing the C-N-M-N chains in their chelate cycles. The spectra exhibit strong exciplex bands in the green to yellow region 540 to 590 nm due to interaction of the excited states of zinc complexes and triaryl molecules of the hole-transporting layer. For some devices, the intrinsic luminescence band of 460 nm in the blue region is also observed along with the exciplex band giving rise to an almost white color of the device emission. The exciplex band can be eliminated if the material of the hole-transporting layer is not a triarylamine derivative. We have also found the exciplex emission in the photoluminescence spectra of the films containing blends of zinc complex and triphenylamine material.

Electroluminescence and rectifying properties of heterojunction LEDs based on ZnO nanorods

International Nuclear Information System (INIS)

Rout, Chandra Sekhar; Rao, C N R

2008-01-01

n-ZnO NR/p-Si and n-ZnO NR/p-PEDOT/PSS heterojunction light-emitting diodes (LEDs) have been fabricated with ZnO nanorods (NRs) grown by a low-temperature method as well as by employing pulsed laser deposition (PLD). The low-temperature method involves growing the ZnO nanorods by the reaction of water with zinc metal. The current-voltage (I-V) characteristics of the heterojunctions show good rectifying diode characteristics. The electroluminescence (EL) spectra of the nanorods show an emission band at around 390 nm and defect related bands in the 400-550 nm region. Room-temperature electroluminescence is detected under forward bias for both the heterostructures. With the low-temperature grown nanorods, the defect related bands in the 400-550 nm range are more intense in the EL spectra, whereas with the PLD grown nanorods, only the 390 nm band is prominent

Exciplex formation and electroluminescent absorption in ultraviolet organic light-emitting diodes

Science.gov (United States)

Zhang, Qi; Zhang, Hao; Zhang, Xiao-Wen; Xu, Tao; Wei, Bin

2015-02-01

We investigated the formation of exciplex and electroluminescent absorption in ultraviolet organic light-emitting diodes (UV OLEDs) using different heterojunction structures. It is found that an energy barrier of over 0.3 eV between the emissive layer (EML) and adjacent transport layer facilitates exciplex formation. The electron blocking layer effectively confines electrons in the EML, which contributes to pure UV emission and enhances efficiency. The change in EML thickness generates tunable UV emission from 376 nm to 406 nm. In addition, the UV emission excites low-energy organic function layers and produces photoluminescent emission. In UV OLED, avoiding the exciplex formation and averting light absorption can effectively improve the purity and efficiency. A maximum external quantum efficiency of 1.2% with a UV emission peak of 376 nm is realized. Project supported by the National Natural Science Foundation of China (Grant Nos. 61136003 and 61275041) and the Guangxi Provincial Natural Science Foundation, China (Grant No. 2012GXNSFBA053168).

Low-threshold pure UV electroluminescence from n-ZnO:Al/i-layer/n-GaN heterojunction

International Nuclear Information System (INIS)

Li Songzhan; Fang Guojia; Long Hao; Wang Haoning; Huang Huihui; Mo Xiaoming; Zhao Xingzhong

2012-01-01

Ultraviolet (UV) electroluminescence (EL) of n-ZnO:Al (AZO)/i-layer/n-GaN heterojunctions with different intrinsic layers has been obtained. Rectifying behavior and EL spectra of the heterojunctions are investigated at room temperature. Under positive voltage, a dominant UV emission peak around ∼370 nm is observed for both AZO/i-ZnO/n-GaN and AZO/i-MgO/n-GaN heterojunctions. Nevertheless, the UV emission peak intensity of AZO/i-MgO/n-GaN heterojunction is much stronger than that of AZO/i-ZnO/n-GaN heterojunction at the same voltage. The threshold voltage of AZO/i-MgO/n-GaN heterostructured device is as low as 2.3 V. The difference of EL spectra and the emission mechanism in these devices are discussed. - Highlights: ► UV electroluminescence of n-ZnO:Al/i-layer/n-GaN heterojunctions has been obtained. ► Under positive voltage, a dominant UV emission peak around ∼370 nm is observed for both heterojunctions. ► The UV emission peak intensity of the heterojunction with i-MgO layer is much stronger than that with i-ZnO layer at the same voltage. ► The threshold voltage of n-ZnO:Al/i-MgO/n-GaN heterostructured device is as low as 2.3 V.

Effect of gold nanorods and nanocubes on electroluminescent performances in organic light-emitting diodes and its working mechanism

Directory of Open Access Journals (Sweden)

Ying Xu

2015-06-01

Full Text Available In this manuscript we investigated the influence of Au nanoparticles on electrical and electroluminescent (EL performances in organic light-emitting diodes (OLEDs via doping as-synthesized Au nanorods (NRs or nanocubes (NCs into hole transport layer (HTL. Through accurately controlling the distance between the Au NRs and the emitting layer, altering the guest emitter’s lifetime, and replacing Au NRs with Au NCs to satisfy a better spectrum overlap with the emission guest, we got a conclusion that doping Au NRs or NCs into HTL has no significant influence on the device’s electrical and EL performances, although we observed an increase in the spontaneous emission rate in a fluorescent material by the exciton-surface plasmon-coupling. Our results suggest that a further research on emission mechanism in surface plasmon-enhanced OLEDs is still in process.

ZnO nanorod based low turn-on voltage LEDs with wide electroluminescence spectra

International Nuclear Information System (INIS)

Jha, S.K.; Kutsay, O.; Bello, I.; Lee, S.T.

2013-01-01

Light emitting diodes (LEDs) based on arrays of n-type ZnO Nanorods were fabricated on p-GaN films using a hydrothermal method. The LEDs emit mainly in blue and UV range of the light. Their current–Voltage (I–V) characteristics typically show a low leakage current (7.2 μA) and a high rectification ratio (3 5 5). Devices operate at a low turn-on voltage of ∼4.5 V. Photoluminescence (PL) and electroluminescence (EL) measurements suggest low density of ZnO defects; however, in some aspects density of interfacial defects still might be considerable in the studied devices. The PL emission is deconvoluted to three peaks that are located at wavelengths of 361, 381, and 397 nm, while the wide EL spectra are deconvoluted to five peaks appearing at 368, 385, 427, 474, and 515 nm. Near-band-edge (NBE) emission of p-GaN and n-ZnO was observed in both the PL and EL spectra. Deconvoluted EL spectra consist of a very wide green band with the peak at 515 nm and extending up to 650 nm (red), and a rarely reported EL emission at 474 nm. Origin of these emissions is discussed, herein. The electrical characteristics together with EL characteristics indicate potential to develop and study p-GaN/n-ZnO nanorod LEDs for white emitting applications. - Highlights: ► A low turn-on voltage (4–4.5 V) and low threshold (5 V) electroluminescence from ZnO/GaN heterostructure. ► A wide spectrum EL emission (360–700 nm) suitable for white LED application. ► EL spectra consist of a rarely reported emission band with peak at 474 nm. ► Low-temperature and solution based fabrication, which is scalable and of low cost.

Electroluminescence of zinc oxide thin-films prepared via polymeric precursor and via sol-gel methods

International Nuclear Information System (INIS)

Lima, S.A.M.; Cremona, M.; Davolos, M.R.; Legnani, C.; Quirino, W.G.

2007-01-01

Zinc oxide (ZnO) is an electroluminescent (EL) material that can emit light in different regions of electromagnetic spectrum when electrically excited. Since ZnO is chemically stable, inexpensive and environmentally friendly material, its EL property can be useful to construct solid-state lamps for illumination or as UV emitter. We present here two wet chemical methods to prepare ZnO thin-films: the Pechini method and the sol-gel method, with both methods resulting in crystalline and transparent films with transmittance >85% at 550 nm. These films were used to make thin-film electroluminescent devices (TFELD) using two different insulator layers: lithium fluoride (LiF) or silica (SiO 2 ). All the devices exhibit at least two wide emission bands in the visible range centered at 420 nm and at 380 nm attributed to the electronic defects in the ZnO optical band gap. Besides these two bands, the device using SiO 2 and ZnO film obtained via sol-gel exhibits an additional band in the UV range centered at 350 nm which can be attributed to excitonic emission. These emission bands of ZnO can transfer their energy when a proper dopant is present. For the devices produced the voltage-current characteristics were measured in a specific range of applied voltage

Electroluminescence from a n-ZnO/p-GaN hybrid LED

Energy Technology Data Exchange (ETDEWEB)

Behrends, Arne; Bakin, Andrey; Waag, Andreas [Institute of Semiconductor Technology, Hans-Sommer Str. 66, 38106 Braunschweig (Germany); Kwack, Ho-Sang; Dang, Le Si [Institut Neel, CNRS-UJF, 25, rue des Martyrs, 38042 Grenoble (France)

2010-06-15

In this work we report on the fabrication and characterization of a n-ZnO/p-GaN heterojunction LED. The p-GaN layer was fabricated using MOCVD on Al{sub 2}O{sub 3} with Mg as the acceptor whereas the ZnO nanostructures were grown in a very simple vapor transport system without any additionally doping. Room temperature electroluminescence (EL) measurements show green deep band emission centered at 2.3 eV which is clearly visible with the naked eye when the structure is forward biased. Cathodoluminescence mapping was performed to explain the absence of the band edge emission in the EL spectrum. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Specific features of electroluminescence in heterostructures with InSb quantum dots in an InAs matrix

Energy Technology Data Exchange (ETDEWEB)

Parkhomenko, Ya. A.; Ivanov, E. V.; Moiseev, K. D., E-mail: mkd@iropt2.ioffe.rssi.ru [Russian Academy of Sciences, Ioffe Physical-Technical Institute (Russian Federation)

2013-11-15

The electrical and electroluminescence properties of a single narrow-gap heterostructure based on a p-n junction in indium arsenide, containing a single layer of InSb quantum dots in the InAs matrix, are studied. The presence of quantum dots has a significant effect on the shape of the reverse branch of the current-voltage characteristic of the heterostructure. Under reverse bias, the room-temperature electroluminescence spectra of the heterostructure with quantum dots, in addition to a negative-luminescence band with a maximum at the wavelength {lambda} = 3.5 {mu}m, contained a positive-luminescence emission band at 3.8 {mu}m, caused by radiative transitions involving localized states of quantum dots at the type-II InSb/InAs heterointerface.

New electroluminescent carbazole-containing conjugated polymer: synthesis, photophysics, and electroluminescence

Czech Academy of Sciences Publication Activity Database

Cimrová, Věra; Ulbricht, C.; Dzhabarov, Vagif; Výprachtický, Drahomír; Egbe, D. A. M.

2014-01-01

Roč. 55, č. 24 (2014), s. 6220-6226 ISSN 0032-3861 R&D Projects: GA ČR GAP106/12/0827; GA ČR(CZ) GA13-26542S Institutional support: RVO:61389013 Keywords : carbazole-containing conjugated polymer * synthesis * photophysics and electroluminescence Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.562, year: 2014

Synthesis and electroluminescent properties of blue emitting materials based on arylamine-substituted diphenylvinylbiphenyl derivatives for organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Lee, Kum Hee; You, Jae Nam; Won, Jiyeon; Lee, Jin Yong [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Seo, Ji Hoon [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@hongik.ac.kr [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2011-10-31

This paper reports the synthesis and electroluminescent properties of a series of blue emitting materials with arylamine and diphenylvinylbiphenyl groups for applications to efficient blue organic light-emitting diodes (OLEDs). All devices exhibited blue electroluminescence with electroluminescent properties that were quite sensitive to the structural features of the dopants in the emitting layers. In particular, the device using dopant 4 exhibited sky-blue emission with a maximum luminance, luminance efficiency, power efficiency, external quantum efficiency and CIE coordinates of 39,000 cd/m{sup 2}, 12.3 cd/A, 7.45 lm/W, 7.71% at 20 mA/cm{sup 2} and (x = 0.17, y = 0.31) at 8 V, respectively. In addition, a blue OLED using dopant 2 with CIE coordinates (x = 0.16, y = 0.18) at 8 V exhibited a luminous efficiency, power efficiency and external quantum efficiency of 4.39 cd/A, 2.46 lm/W and 2.97% at 20 mA/cm{sup 2}, respectively.

Electroluminescence spectra of an STM-tip-induced quantum dot

NARCIS (Netherlands)

Croitoru, M.D.; Gladilin, V.N.; Fomin, V.; Devreese, J.T.; Kemerink, M.; Koenraad, P.M.; Sauthoff, K.; Wolter, J.H.; Long, A.R.; Davies, J.H.

2003-01-01

We analyse the electroluminescence measurements performed on a STM-tipImduced quantum dot in a GaAs layer. Positions of electroluminescence peaks, attributed to the electron-hole recombination in the quantum dot, are very sensitive to the electron tunnelling current even in the case when the current

Red electroluminescent process excited by hot holes in SrGa2S4:Ce, Mn thin film

International Nuclear Information System (INIS)

Tanaka, Katsu; Okamoto, Shinji

2009-01-01

This paper reports the first observation of red electroluminescence (EL) in SrGa 2 S 4 :Ce, Mn thin film. The EL spectrum consists of single broad emission band having a peak wavelength of 665 nm. The dominant EL decay time was 31 μs. The relationship between the applied voltage and the EL waveform was measured in single insulating thin film electroluminescent (TFEL) devices. An asymmetric EL waveform was observed in SrGa 2 S 4 :Ce, Mn TFEL devices under a rectangular applied voltage. The polarity of the EL waveform in these devices was different from the waveform in manganese-activated zinc sulfide ZnS:Mn devices. This indicates that hot holes excite the Mn 2+ ions to cause the red EL.

Transient electroluminescence on pristine and degraded phosphorescent blue OLEDs

Science.gov (United States)

Niu, Quan; Blom, Paul W. M.; May, Falk; Heimel, Paul; Zhang, Minlu; Eickhoff, Christian; Heinemeyer, Ute; Lennartz, Christian; Crǎciun, N. Irina

2017-11-01

In state-of-the-art blue phosphorescent organic light-emitting diode (PHOLED) device architectures, electrons and holes are injected into the emissive layer, where they are carried by the emitting and hole transporting units, respectively. Using transient electroluminescence measurements, we disentangle the contribution of the electrons and holes on the transport and efficiency of both pristine and degraded PHOLEDs. By varying the concentration of hole transporting units, we show that for pristine PHOLEDs, the transport is electron dominated. Furthermore, degradation of the PHOLEDs upon electrical aging is not related to the hole transport but is governed by a decrease in the electron transport due to the formation of electron traps.

Enhancement of electroluminescence from embedded Si quantum dots/SiO2multilayers film by localized-surface-plasmon and surface roughening.

Science.gov (United States)

Li, Wei; Wang, Shaolei; Hu, Mingyue; He, Sufeng; Ge, Pengpeng; Wang, Jing; Guo, Yan Yan; Zhaowei, Liu

2015-07-03

In this paper, we prepared a novel structure to enhance the electroluminescence intensity from Si quantum dots/SiO2multilayers. An amorphous Si/SiO2 multilayer film was fabricated by plasma-enhanced chemical vapor deposition on a Pt nanoparticle (NP)-coated Si nanopillar array substrate. By thermal annealing, an embedded Si quantum dot (QDs)/SiO2 multilayer film was obtained. The result shows that electroluminescence intensity was significantly enhanced. And, the turn-on voltage of the luminescent device was reduced to 3 V. The enhancement of the light emission is due to the resonance coupling between the localized-surface-plasmon (LSP) of Pt NPs and the band-gap emission of Si QDs/SiO2 multilayers. The other factors were the improved absorption of excitation light and the increase of light extraction ratio by surface roughening structures. These excellent characteristics are promising for silicon-based light-emitting applications.

Effect of interface voids on electroluminescence colors for ZnO microdisk/p-GaN heterojunction light-emitting diodes

Science.gov (United States)

Mo, Ran; Choi, Ji Eun; Kim, Hyeong Jin; Jeong, Junseok; Kim, Jong Chan; Kim, Yong-Jin; Jeong, Hu Young; Hong, Young Joon

2017-10-01

This study investigates the influence of voids on the electroluminescence (EL) emission color of ZnO microdisk/p-GaN heterojunction light-emitting diodes (LEDs). For this study, position-controlled microdisk arrays were fabricated on patterned p-GaN via wet chemical epitaxy of ZnO, and specifically, the use of trisodium citrate dihydrate (TCD) yielded high-density voids at the bottom of the microdisk. Greenish yellow or whitish blue EL was emitted from the microdisk LEDs formed with or without TCD, respectively, at reverse-bias voltages. Such different EL colors were found to be responsible for the relative EL intensity ratio between indigo and yellow emission peaks, which were originated from radiative recombination at p-GaN and ZnO, respectively. The relative EL intensity between dichromatic emissions is discussed in terms of (i) junction edge effect provoked by interfacial voids and (ii) electron tunneling probability depending on the depletion layer geometry.

Investigation of thioglycerol stabilized ZnS quantum dots in electroluminescent device performance

Science.gov (United States)

Ethiraj, Anita Sagadevan; Rhen, Dani; Lee, D. H.; Kang, Dae Joon; Kulkarni, S. K.

2016-05-01

The present work is focused on the investigation of thioglycerol (TG) stabilized Zinc Sulfide Quantum dots (ZnS QDs) in the hybrid electroluminescence (EL) device. Optical absorption spectroscopy clearly indicates the formation of narrow size distributed ZnS in the quantum confinement regime. X-ray Diffraction (XRD), Photoluminescence (PL), Energy Dispersive X-ray Spectroscopy (EDS) data supports the same. The hybrid EL device with structure of ITO (indium tin oxide)//PEDOT:PSS ((poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate)//HTL (α NPD- N,N'-diphenyl-N,N'-bis(1-naphthyl)-(1,1'-phenyl)-4,4'-diamine// PVK:ZnS QDs//ETL(PBD- 2-tert-butylphenyl- 5-biphenyl-1,3,4-oxadiazole)//LiF:Al (Device 1) was fabricated. Reference device without the ZnS QDs were also prepared (Device 2). The results show that the ZnS QDs based device exhibited bright electroluminescence emission of 24 cd/m2 at a driving voltage of 16 Volts under the forward bias conditions as compared to the reference device without the ZnS QDs, which showed 6 cd/m2 at ˜22 Volts.

The effect of DCJTB doping concentration in PVK on the chromatic coordinate of electroluminescence

Energy Technology Data Exchange (ETDEWEB)

Zhang, F J; Xu, Z; Zhao, S L; Wang, L W; Yuan, G C [Key Laboratory of Luminescence and Optical Information (Beijing Jiaotong University), Ministry of Education (China); Zhao, D W [School of Electrical and Electronic Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore)], E-mail: fjzhang@bjtu.edu.cn

2008-05-15

The dominant mechanism of electroluminescence (EL) from 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran (DCJTB) doped in poly-(N-vinyl-carbazole) (PVK) system was demonstrated to be a charge carrier trapped by DCJTB molecular rather than Foerster energy transfer from PVK to DCJTB. The chromatically coordinate EL emission of PVK:DCJTB changes from (0.41, 0.31) to (0.67, 0.31) with an increase in DCJTB doping concentration. The emission peak in DCJTB shows red-shift and the shoulder emission peak at 656 nm becomes stronger as the doping concentration increases. The effect of DCJTB doping concentration on EL spectra is attributed to strong dipole-dipole interaction between the DCJTB molecule with an increase in doping concentration.

White-light emission from porous-silicon-aluminium Schottky junctions

International Nuclear Information System (INIS)

Masini, G.; La Monica, S.; Maiello, G.

1996-01-01

Porous-silicon-based white-light-emitting devices are presented. The fabrication process on different substrates is described. The peculiarities of technological steps for device fabrication (porous-silicon formation and aluminium treatment) are underlined. Doping profile of the porous layer, current-voltage characteristics, time response, lifetime tests and electroluminescence emission spectrum of the device are presented. A model for electrical behaviour of Al/porous silicon Schottky junction is presented. Electroluminescence spectrum of the presented devices showed strong similarities with white emission from crystalline silicon junctions in the breakdown region

Electroluminescence from ZnO/Si heterojunctions fabricated by PLD with bias voltage application

Science.gov (United States)

Seno, Yuuki; Konno, Daisuke; Komiyama, Takao; Chonan, Yasunori; Yamaguchi, Hiroyuki; Aoyama, Takashi

2014-02-01

Electroluminescence (EL) for ZnO films has been investigated by fabricating n-ZnO/p-Si heterojunctions and changing the VI/II (O/Zn) ratio of the films. In the photoluminescence (PL) spectra, both the near band edge (NBE) emission and the defect-related emission were observed, while in the EL spectra only defect-related emission was observed. The EL spectra were divided into three components: green (550 nm), yellow (618 nm) and red (700 nm) bands; and their intensities were compared. As the VI/II (O/Zn) ratio was increased, the red band emission intensity decreased and the green band emission intensity increased. This implies that the oxygen and the zinc vacancies are related to the red and the green band emissions, respectively. Electron transitions from the conduction band minimum (Ec) to the deep energy levels of these vacancies are suggested to cause the red and the green luminescences while the energy levels of the Zn interstitials are close to the Ec in the band gap and no NBE emission is observed.

Electroluminescence from ZnO/Si heterojunctions fabricated by PLD with bias voltage application

International Nuclear Information System (INIS)

Seno, Yuuki; Konno, Daisuke; Komiyama, Takao; Chonan, Yasunori; Yamaguchi, Hiroyuki; Aoyama, Takashi

2014-01-01

Electroluminescence (EL) for ZnO films has been investigated by fabricating n-ZnO/p-Si heterojunctions and changing the VI/II (O/Zn) ratio of the films. In the photoluminescence (PL) spectra, both the near band edge (NBE) emission and the defect-related emission were observed, while in the EL spectra only defect-related emission was observed. The EL spectra were divided into three components: green (550 nm), yellow (618 nm) and red (700 nm) bands; and their intensities were compared. As the VI/II (O/Zn) ratio was increased, the red band emission intensity decreased and the green band emission intensity increased. This implies that the oxygen and the zinc vacancies are related to the red and the green band emissions, respectively. Electron transitions from the conduction band minimum (Ec) to the deep energy levels of these vacancies are suggested to cause the red and the green luminescences while the energy levels of the Zn interstitials are close to the Ec in the band gap and no NBE emission is observed

Electroluminescence Spectrum Shift with Switching Behaviour of Diamond Thin Films

Institute of Scientific and Technical Information of China (English)

王小平; 王丽军; 张启仁; 姚宁; 张兵临

2003-01-01

We report a special phenomenon on switching behaviour and the electroluminescence (EL) spectrum shift of doped diamond thin films. Nitrogen and cerium doped diamond thin films were deposited on a silicon substrate by microwave plasma-assisted chemical vapour deposition system and other special techniques. An EL device with a three-layer structure of nitrogen doped diamond/cerium doped diamond/SiO2 thin films was made. The EL device was driven by a direct-current power supply. Its EL character has been investigated, and a switching behaviour was observed. The EL light emission colour of diamond films changes from yellow (590nm) to blue (454 nm) while the switching behaviour appears.

Large-area and bright pulsed electroluminescence in monolayer semiconductors

KAUST Repository

Lien, Der-Hsien; Amani, Matin; Desai, Sujay B.; Ahn, Geun Ho; Han, Kevin; He, Jr-Hau; Ager, Joel W.; Wu, Ming C.; Javey, Ali

2018-01-01

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS, WS, MoSe, and WSe) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.

Large-area and bright pulsed electroluminescence in monolayer semiconductors

KAUST Repository

Lien, Der-Hsien

2018-04-04

Transition-metal dichalcogenide monolayers have naturally terminated surfaces and can exhibit a near-unity photoluminescence quantum yield in the presence of suitable defect passivation. To date, steady-state monolayer light-emitting devices suffer from Schottky contacts or require complex heterostructures. We demonstrate a transient-mode electroluminescent device based on transition-metal dichalcogenide monolayers (MoS, WS, MoSe, and WSe) to overcome these problems. Electroluminescence from this dopant-free two-terminal device is obtained by applying an AC voltage between the gate and the semiconductor. Notably, the electroluminescence intensity is weakly dependent on the Schottky barrier height or polarity of the contact. We fabricate a monolayer seven-segment display and achieve the first transparent and bright millimeter-scale light-emitting monolayer semiconductor device.

Color tunable electroluminescence and resistance switching from a ZnO-nanorod–TaO_x–p-GaN heterojunction

International Nuclear Information System (INIS)

Zhao, J L; Teo, K L; Zheng, K; Sun, X W

2016-01-01

Well-aligned ZnO nanorods have been prepared on p-GaN–sapphire using a vapor phase transport (VPT) technique. A thin sputtered layer of TaO_x is employed as the intermediate layer and an n-ZnO–TaO_x–p-GaN heterojunction device has been achieved. The current transport of the heterojunction exhibited a typical resistance switching behavior, which originated from the filament forming and breaking in the TaO_x layer. Color controllable electroluminescence (EL) was observed from the biased heterojunction at room temperature. Bluish-white wide band emission is achieved from the forward biased device in both the high resistance and low resistance states, while red emission can only be observed for the reverse biased device in the low resistance state. The correlation between the EL and resistance switching has been analyzed in-depth based on the interface band diagram of the heterojunction. (paper)

Hybrid electroluminescent devices

Science.gov (United States)

Shiang, Joseph John; Duggal, Anil Raj; Michael, Joseph Darryl

2010-08-03

A hybrid electroluminescent (EL) device comprises at least one inorganic diode element and at least one organic EL element that are electrically connected in series. The absolute value of the breakdown voltage of the inorganic diode element is greater than the absolute value of the maximum reverse bias voltage across the series. The inorganic diode element can be a power diode, a Schottky barrier diode, or a light-emitting diode.

Electroluminescence Efficiency Enhancement using Metal Nanoparticles

National Research Council Canada - National Science Library

Soref, Richard A; Khurgin, J. B; Sun, G

2008-01-01

We apply the "effective mode volume" theory to evaluate enhancement of the electroluminescence efficiency of semiconductor emitters placed in the vicinity of isolated metal nanoparticles and their arrays...

Novel Mechano-Luminescent Sensors Based on Piezoelectric/Electroluminescent Composites

Directory of Open Access Journals (Sweden)

Yunzhang Fang

2011-04-01

Full Text Available A high-sensitivity mechano-luminescent sensor was fabricated on the basis of piezoelectric/electroluminescent composites. The working principle of this mechano-luminescent sensor was elucidated by analyzing the relationship between the piezoelectric-induced charges and the electroluminescent effects. When a stress is applied on the piezoelectric layer, electrical charges will be induced at both the top and bottom sides of the piezoelectric layer. The induced electrical charges will lead to a light output from the electroluminescent layer, thus producing a mechano-luminescence effect. By increasing the vibration strength or frequency applied, the mechano-luminescence output can be obviously enhanced. Mechano-luminescence sensors have potential in smart stress-to-light devices, such as foot-stress-distribution-diagnosis systems and dynamic-load-monitors for bridge hanging cables.

Electroluminescence of a polythiophene molecular wire suspended between a metallic surface and the tip of a scanning tunneling microscope.

Science.gov (United States)

Reecht, Gaël; Scheurer, Fabrice; Speisser, Virginie; Dappe, Yannick J; Mathevet, Fabrice; Schull, Guillaume

2014-01-31

The electroluminescence of a polythiophene wire suspended between a metallic surface and the tip of a scanning tunneling microscope is reported. Under positive sample voltage, the spectral and voltage dependencies of the emitted light are consistent with the fluorescence of the wire junction mediated by localized plasmons. This emission is strongly attenuated for the opposite polarity. Both emission mechanism and polarity dependence are similar to what occurs in organic light emitting diodes (OLED) but at the level of a single molecular wire.

A Stretchable Alternating Current Electroluminescent Fiber

Directory of Open Access Journals (Sweden)

Dan Hu

2018-01-01

Full Text Available Flexible, stretchable electroluminescent fibers are of significance to meet the escalating requirements of increasing complexity and multifunctionality of smart electronics. We report a stretchable alternating current electroluminescent (ACEL fiber by a low-cost and all solution-processed scalable process. The ACEL fiber provides high stretchability, decent light-emitting performance, with excellent stability and nearly zero hysteresis. It can be stretched up to 80% strain. Our ACEL fiber device maintained a stable luminance for over 6000 stretch-release cycles at 50% strain. The mechanical stretchability and optical stability of our ACEL fiber device provides new possibilities towards next-generation stretchable displays, electronic textiles, advanced biomedical imaging and lighting, conformable visual readouts in arbitrary shapes, and novel health-monitoring devices.

Direct Integration of Dynamic Emissive Displays into Knitted Fabric Structures

Science.gov (United States)

Bellingham, Alyssa

Smart textiles are revolutionizing the textile industry by combining technology into fabric to give clothing new abilities including communication, transformation, and energy conduction. The advent of electroluminescent fibers, which emit light in response to an applied electric field, has opened the door for fabric-integrated emissive displays in textiles. This thesis focuses on the development of a flexible and scalable emissive fabric display with individually addressable pixels disposed within a fabric matrix. The pixels are formed in areas where a fiber supporting the dielectric and phosphor layers of an electroluminescent structure contacts a conductive surface. This conductive surface can be an external conductive fiber, yarn or wire, or a translucent conductive material layer deposited at set points along the electroluminescent fibers. Different contacting methods are introduced and the different ways the EL yarns can be incorporated into the knitted fabric are discussed. EL fibers were fabricated using a single yarn coating system with a custom, adjustable 3D printed slot die coater for even distribution of material onto the supporting fiber substrates. These fibers are mechanically characterized inside of and outside of a knitted fabric matrix to determine their potential for various applications, including wearables. A 4-pixel dynamic emissive display prototype is fabricated and characterized. This is the first demonstration of an all-knit emissive display with individually controllable pixels. The prototype is composed of a grid of fibers supporting the dielectric and phosphor layers of an electroluminescent (EL) device structure, called EL fibers, and conductive fibers acting as the top electrode. This grid is integrated into a biaxial weft knit structure where the EL fibers make up the rows and conductive fibers make up the columns of the reinforcement yarns inside the supporting weft knit. The pixels exist as individual segments of

Investigations on electroluminescent tapes and foils in relation to their applications in automotive

Science.gov (United States)

Plotog, Ioan

2015-02-01

The electroluminescent (EL) tapes or foils having barrier films for an additional level of protection against the toughest environments conditions, offer a large area of applications. The EL lights, due to their characteristics, began to be used not only in the entertainment industry, but also for automotive and aerospace applications. In the paper, the investigations regarding EL foils technical performances in relation to their applications as light sources in automotive ambient light were presented. The experiments were designed based on the results of EL foils electrical properties previous investigations done in laboratory conditions, taking into account the range of automotive ambient temperatures for sinusoidal alternative supply voltage. The measurements for different temperatures were done by keeping the EL foils into electronic controlled oven that ensures the dark enclosure offering conditions to use a lux-meter in order to measure and maintain under control light emission intensity. The experiments results define the EL foils characteristics as load in automotive ambient temperatures condition, assuring so the data for optimal design of a dedicated inverter.

Molecular-scale simulation of electroluminescence in a multilayer white organic light-emitting diode

DEFF Research Database (Denmark)

Mesta, Murat; Carvelli, Marco; de Vries, Rein J

2013-01-01

we show that it is feasible to carry out Monte Carlo simulations including all of these molecular-scale processes for a hybrid multilayer organic light-emitting diode combining red and green phosphorescent layers with a blue fluorescent layer. The simulated current density and emission profile......In multilayer white organic light-emitting diodes the electronic processes in the various layers--injection and motion of charges as well as generation, diffusion and radiative decay of excitons--should be concerted such that efficient, stable and colour-balanced electroluminescence can occur. Here...

Room-temperature electroluminescence of Er-doped hydrogenated amorphous silicon

Energy Technology Data Exchange (ETDEWEB)

Gusev, Oleg; Bresler, Mikhail; Kuznetsov, Alexey; Kudoyarova, Vera; Pak, Petr; Terukov, Evgenii; Tsendin, Konstantin; Yassievich, Irina [A F Ioffe Physico-Technical Institute, Politekhnicheskaya 26, 194021 St. Petersburg (Russian Federation); Fuhs, Walther [Hahn-Meitner Institut, Abteilung Photovoltaik, Rudower Chaussee 5, D-12489 Berlin (Germany); Weiser, Gerhard [Phillips-Universitat Marburg, Fachbereich Physik, D-35032 Marburg (Germany)

1998-05-11

We have observed room-temperature erbium-ion electroluminescence in erbium-doped amorphous silicon. Electrical conduction through the structure is controlled by thermally activated ionization of deep D{sup -} defects in an electric field and the reverse process of capture of mobile electrons by D{sup 0} states. Defect-related Auger excitation (DRAE) is responsible for excitation of erbium ions located close to dangling-bond defects. Our experimental data are consistent with the mechanisms proposed

Influence of surface wettability on cathode electroluminescence of porous silicon

International Nuclear Information System (INIS)

Goryachev, D.N.; Sreseli, O.M.; Belyakov, L.V.

1997-01-01

Influence of porous silicon wettability on efficiency of its cathode electroluminescence in electrolytes was investigated. It was revealed that increase of porous silicon wettability by electrolyte improved contact with a sublayer and provided generation of sufficient quantity of charge carriers. Diffusion - ionic, not electronic mechanism of charge transfer to the centers of micro crystallite electroluminescence is observed in porous silicon - electrolyte systems

Charge transfer through amino groups-small molecules interface improving the performance of electroluminescent devices

Science.gov (United States)

Havare, Ali Kemal; Can, Mustafa; Tozlu, Cem; Kus, Mahmut; Okur, Salih; Demic, Şerafettin; Demirak, Kadir; Kurt, Mustafa; Icli, Sıddık

2016-05-01

A carboxylic group functioned charge transporting was synthesized and self-assembled on an indium tin oxide (ITO) anode. A typical electroluminescent device [modified ITO/TPD (50 nm)/Alq3 (60 nm)/LiF (2 nm)/(120 nm)] was fabricated to investigate the effect of the amino groups-small molecules interface on the characteristics of the device. The increase in the surface work function of ITO is expected to facilitate the hole injection from the ITO anode to the Hole Transport Layer (HTL) in electroluminescence. The modified electroluminescent device could endure a higher current and showed a much higher luminance than the nonmodified one. For the produced electroluminescent devices, the I-V characteristics, optical characterization and quantum yields were performed. The external quantum efficiency of the modified electroluminescent device is improved as the result of the presence of the amino groups-small molecules interface.

Direct current electroluminescence in rare-earth-doped zinc sulphide

International Nuclear Information System (INIS)

Bryant, F.J.; Krier, A.

1984-01-01

Some of the properties and characteristics of rare-earth-doped zinc sulphide DCEL devices are reported. Two types of devices are discussed, co-evaporated ZnS:RE thin films and ion implanted ZnS:RE single crystal diodes. The thin film devices exhibit bright DCEL of various colours at low applied voltages (typically approximately 12 V). A study of the spectral intensities and lifetimes of the Er 3+ ion in ZnS:Er 3+ thin films is consistent with a Boltzmann energy distribution amongst the conduction electrons present in these devices. The ZnS:RE single crystal diodes fabricated in this laboratory by ion implantation are also capable of various colour DCEL. By comparing the EL emission obtained from the different rare earth dopants, erbium and neodymium are identified as the most efficient luminescence centres. Further consideration of the EL emission spectra gives evidence for the presence of inter-conduction band hot electron transitions in those devices containing rare earth dopants which are inefficent electroluminescence centres. These findings can be explained in terms of Auger processes occurring in rare earth complexes. (author)

Emission properties of porphyrin compounds in new polymeric PS:CBP host

Science.gov (United States)

Jafari, Mohammad Reza; Bahrami, Bahram

2015-06-01

In this study, a device with fundamental structure of ITO/PEDOT:PSS (60 nm)/PS:CBP (70 nm)/Al (150 nm) was fabricated. The electroluminescence spectrum of device designated a red shift rather than PS:CBP photoluminescence spectra. It can be suggested that the electroplex emission occurs at PS:CBP interface. By following this step, red light-emitting devices using porphyrin compounds as a red dopant in a new host material PS:CBP with a configuration of ITO/PEDOT:PSS (60 nm)/PS:CBP:porphyrin compounds(70 nm)/Al (150 nm) have been fabricated and investigated. The electroluminescent spectra of the porphyrin compounds were red-shifted as compared with the PS:CBP blend. OLED devices based on doping 3,4PtTPP and TPPNO2 in PS:CBP showed purer red emission compared with ZnTPP and CoTPP doped devices. We believe that the electroluminescence performance of OLED devices based on porphyrin compounds depends on overlaps between the absorption of the porphyrin compounds and the emission of PS:CBP.

Plasmonic enhancement of electroluminescence

Science.gov (United States)

Guzatov, D. V.; Gaponenko, S. V.; Demir, H. V.

2018-01-01

Here plasmonic effect specifically on electroluminescence (EL) is studied in terms of radiative and nonradiative decay rates for a dipole near a metal spherical nanoparticle (NP). Contribution from scattering is taken into account and is shown to play a decisive role in EL enhancement owing to pronounced size-dependent radiative decay enhancement and weak size effect on non-radiative counterpart. Unlike photoluminescence where local incident field factor mainly determines the enhancement possibility and level, EL enhancement is only possible by means of quantum yield rise, EL enhancement being feasible only for an intrinsic quantum yield Q0 red-orange range only. Independently of positive effect on quantum yield, metal nanoparticles embedded in an electroluminescent device will improve its efficiency at high currents owing to enhanced overall recombination rate which will diminish manifestation of Auger processes. The latter are believed to be responsible for the known undesirable efficiency droop in semiconductor commercial quantum well based LEDs at higher current. For the same reason plasmonics can diminish quantum dot photodegradation from Auger process induced non-radiative recombination and photoionization thus opening a way to avoid negative Auger effects in emerging colloidal semiconductor LEDs.

On the origin of excimer emission in electroluminescence and photoluminescence spectra of polyfluorenes

International Nuclear Information System (INIS)

Vacha, Martin; Ha, Jaekook; Sato, Hisaya

2007-01-01

We report a study on the differences in red-shifted excimer band in photoluminescence (PL) and electroluminescence (EL) spectra of thin films of a copolymer of dibutylfluorene and butylphenylphenoxazine. The relative intensity of the excimer band in PL spectra increases with temperature above the polymer glass transition, and with the intensity of the excitation light. In EL spectra, on the other hand, the relative excimer intensity is seen to decrease with increasing driving voltage. These opposite trends originate from the different nature of excitations in PL and EL spectra: photoexcitation directly creates singlet excitons while electric excitation proceeds via interaction of injected electrons and holes. In case of electric excitation, the observed results might be due to trap-assisted excimer formation

Bidirectional electroluminescence from p-SnO2/i-MgZnO/n-ZnO heterojunction light-emitting diodes

International Nuclear Information System (INIS)

Yang, Yanqin; Li, Songzhan; Liu, Feng; Zhang, Nangang; Liu, Kan; Wang, Shengxiang; Fang, Guojia

2017-01-01

Light-emitting diodes based on p-SnO 2 /i-MgZnO/n-ZnO heterojunction have been fabricated. The material properties and the performance of heterojunction device are characterized. Current-voltage characteristics of the device show a diode-like rectifying behavior. Under forward bias, two prominent emission peaks located at 589 nm and 722 nm in the visible region and a weak ultraviolet emission are observed from p-SnO 2 /i-MgZnO/n-ZnO heterojunction device. As the device is under reverse bias, a broad visible emission band dominates the electroluminescence spectrum at a high current. Furthermore, the emission mechanism has been discussed in terms of energy band structures of the device under forward and reverse biases.

Origin of the Electroluminescence from Annealed-ZnO/GaN Heterojunction Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Kai-Chiang Hsu

2015-11-01

Full Text Available This paper addressed the effect of post-annealed treatment on the electroluminescence (EL of an n-ZnO/p-GaN heterojunction light-emitting diode (LED. The bluish light emitted from the 450 °C-annealed LED became reddish as the LED annealed at a temperature of 800 °C under vacuum atmosphere. The origins of the light emission for these LEDs annealed at various temperatures were studied using measurements of electrical property, photoluminescence, and Auger electron spectroscopy (AES depth profiles. A blue-violet emission located at 430 nm was associated with intrinsic transitions between the bandgap of n-ZnO and p-GaN, the green-yellow emission at 550 nm mainly originating from the deep-level transitions of native defects in the n-ZnO and p-GaN surfaces, and the red emission at 610 nm emerging from the Ga-O interlayer due to interdiffusion at the n-ZnO/p-GaN interface. The above-mentioned emissions also supported the EL spectra of LEDs annealed at 700 °C under air, nitrogen, and oxygen atmospheres, respectively.

Influence of Exciplex formation on the electroluminescent properties of dimeric Zn (II) bis-2-(2'-hydroxyphenyl) benzoxazole complex and monomeric Zn (II) 2-(1'-hydroxynaphthyl) benzothiazole complex

Science.gov (United States)

Prakash, Sattey; Anand, R. S.; Manoharan, S. Sundar

2011-10-01

In this paper we present the factors affecting electroluminescent properties of Zinc complexes of oxazole & thiazole derivatives. Electroluminescent spectra of the Zinc (II) complex of bis-[2-(2'-hydroxyphenyl) benzoxazole], [Zn (HPBO)2]2 and 2-(1'-hydroxynaphthyl) benzothiazole [Zn (HNBT)2] show unusual broadening and shows structural and photophysical similarity with [Zn (HPBT)2]2, a dimeric complex. The [Zn (HPBO)2]2 complex as an emissive layer in the device structure ITO /PEDOT:PSS /TPD (30nm) /[Zn (HPBO)2]2 (60nm) /BCP (6nm) /Ca (3nm) /Al (200nm) shows a broad bluish green emission, with a full width at half maxima (FWHM1˜70nm). The EL spectra is much broader compared to the PL spectra because of exciplex formation at the interfacial region between the emissive layer (EML) & hole transport layer (HTL). We also show the device performance of Zinc 2-(1'-hydroxynaphthyl) benzothiazole [Zn (HNBT)2] complex as emissive layer. Distinctly this device shows a broad greenish yellow emission with a peak maxima at 535nm and 690nm, owing to the exciplex formation between electron transport layer (ETL) and emissive layer (EML), which is in sharp contrast to the exciplex formation across the HTL-EML interface observed for the [Zn (HPBO)2]2 complex.

Efficient light emitting devices based on phosphorescent partially doped emissive layers

KAUST Repository

Yang, Xiaohui; Jabbour, Ghassan E.

2013-01-01

We report efficient organic light emitting devices employing an ultrathin phosphor emissive layer. The electroluminescent spectra of these devices can be tuned by introducing a low-energy emitting phosphor layer into the emission zone. Devices

Bidirectional electroluminescence from p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Yang, Yanqin [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Li, Songzhan, E-mail: liszhan@whu.edu.cn [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Key Lab of Artificial Micro- and Nano-Structures of Ministry of Education of China, School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Liu, Feng; Zhang, Nangang; Liu, Kan [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Wang, Shengxiang, E-mail: sxwang@wtu.edu.cn [School of Electronic and Electrical Engineering, Hubei Collaborative Innovation Center of Textile Industrial Chain Generic Technology, Wuhan Textile University, Wuhan 430073 (China); Fang, Guojia [Key Lab of Artificial Micro- and Nano-Structures of Ministry of Education of China, School of Physics and Technology, Wuhan University, Wuhan 430072 (China)

2017-06-15

Light-emitting diodes based on p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction have been fabricated. The material properties and the performance of heterojunction device are characterized. Current-voltage characteristics of the device show a diode-like rectifying behavior. Under forward bias, two prominent emission peaks located at 589 nm and 722 nm in the visible region and a weak ultraviolet emission are observed from p-SnO{sub 2}/i-MgZnO/n-ZnO heterojunction device. As the device is under reverse bias, a broad visible emission band dominates the electroluminescence spectrum at a high current. Furthermore, the emission mechanism has been discussed in terms of energy band structures of the device under forward and reverse biases.

White electroluminescence from ZnO nanorods/p-GaN heterojunction light-emitting diodes under reverse bias

International Nuclear Information System (INIS)

Zhang, Lichun; Li, Qingshan; Qu, Chong; Zhang, Zhongjun; Huang, Ruizhi; Zhao, Fengzhou

2013-01-01

Heterojunction light-emitting diodes (LEDs) based on arrays of ZnO nanorods were fabricated on p-GaN films by the hydrothermal method. Without any phosphors, white-light electroluminescence (EL) from ZnO nanorods/p-GaN heterojunction LEDs operated at reverse breakdown bias was observed. The EL spectra are composed of an ultraviolet (UV) emission centered at 382 nm, a blue light located at 431 nm and a broadband yellow–green light at around 547 nm, which originated from band-edge emission in ZnO, the Mg acceptor levels in p-GaN and the deep-level states near the ZnO/GaN interface, respectively. The chromaticity coordinates of EL spectrum are very close to the (0.333, 0.333) of standard white light. The origin of these emissions has been discussed and the tunneling effect in the interface is probably the mechanism to explain EL emission. (paper)

Coordination compounds of rare-earth metals with organic ligands for electroluminescent diodes

International Nuclear Information System (INIS)

Katkova, M A; Bochkarev, Mikhail N; Vitukhnovsky, Alexey G

2005-01-01

Data on lanthanide coordination compounds with organic ligands used in the design of electroluminescent diodes are summarised and systematically represented. The molecular and electronic structures and spectroscopic characteristics of these compounds are considered. A comparative analysis of the properties of organic electroluminescent diodes with different compositions of emitting and conductive layers is presented.

Investigating side chain mediated electroluminescence from carbazole-modified polyfluorene.

Science.gov (United States)

Liao, Jin-Long; Chen, Xiwen; Liu, Ching-Yang; Chen, Show-An; Su, Chiu-Huen; Su, An-Chung

2007-09-06

In molecular design of electroluminescent (EL) conjugated polymers, introducing a charge transport moiety on a side chain is found to be a promising method for balancing electron and hole fluxes in EL devices without changing the emitting color if there is no interaction between moiety and main chain. In the case of grafting a carbazole (Cz) moiety (hole transporting) on blue emitting polyfluorene, a green emission appears with intensity comparable to the blue emission, which was attributed to a possible interaction between main chain and Cz as previously reported by us. Here, a detailed study of its EL mechanism was carried out by means of time-resolved EL with the assistance of molecular simulation and thermally stimulated current measurements; exploration of how main chain segments interact with the transport moiety was performed. We found the Cz groups in Cz100PF play multiple roles: they act as (1) hole transporter to improve hole injection, (2) hole trapping site for efficient electron-hole recombination to yield blue-emitting excitons, and (3) source of green emission from electroplex formed via electric field-mediated interaction of the Cz/Cz radical cation with an electron in the nearby PF backbone. In combination, these observations suggest that integrated consideration for both intramolecular and intermolecular interactions provides a new route of molecular design of efficient EL polymers.

Localized Surface Plasmon-Enhanced Electroluminescence in OLEDs by Self-Assembly Ag Nanoparticle Film

Science.gov (United States)

He, Xiaoxiao; Wang, Wenjun; Li, Shuhong; Wang, Qingru; Zheng, Wanquan; Shi, Qiang; Liu, Yunlong

2015-12-01

We fabricated Ag nanoparticle (NP) film in organic light emission diodes (OLEDs), and a 23 times increase in electroluminescence (EL) at 518 nm was probed by time-resolved EL measurement. The luminance and relative external quantum efficiency (REQE) were increased by 5.4 and 3.7 times, respectively. There comes a new energy transport way that localized surface plasmons (LSPs) would absorb energy that corresponds to the electron-hole pair before recombination, promoting the formation of electron-hole pair and exciting local surface plasmon resonance (LSPR). The extended lifetime of Alq3 indicates the existence of strong interaction between LSPR and exciton, which decreases the nonradiative decay rate of OLEDs.

Hole-exciton interaction induced high field decay of magneto-electroluminescence in Alq3-based organic light-emitting diodes at room temperature

Science.gov (United States)

Zhang, Tingting; Holford, D. F.; Gu, Hang; Kreouzis, T.; Zhang, Sijie; Gillin, W. P.

2016-01-01

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq3) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq3 system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there is also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.

The effect of the thicknesses of the various layers on the colour emitted by an organic electroluminescent device

Science.gov (United States)

Jolinat, P.; Clergereaux, R.; Farenc, J.; Destruel, P.

1998-05-01

Organic electroluminescent diodes based on thin organic layers are one of the most promising next-generation systems for the backlighting of the liquid crystal screens. Among other methods to obtain white light, three-layer luminescent devices with each layer emitting one of the three fundamental colours have been studied here. Red, green and blue light were produced by 0022-3727/31/10/018/img1 doped with Nile red, 0022-3727/31/10/018/img1 and TPD layers respectively. A fourth thin film of TAZ has been inserted between TPD and 0022-3727/31/10/018/img1 to control injection of electrons into the TPD. The effect of the layers' thicknesses on the spectral emission of the device has been examined. Results show that the thicknesses of TAZ and doped 0022-3727/31/10/018/img1 layers have to be controlled to within a precision of better than 5 Å. The discussion turns on the possibility of applying this technology to screen backlighting.

Blue and green electroluminescence from CdSe nanocrystal quantum-dot-quantum-wells

International Nuclear Information System (INIS)

Lu, Y. F.; Cao, X. A.

2014-01-01

CdS/CdSe/ZnS quantum dot quantum well (QDQW) nanocrystals were synthesized using the successive ion layer adsorption and reaction technique, and their optical properties were tuned by bandgap and strain engineering. 3-monolayer (ML) CdSe QWs emitted blue photoluminescence at 467 nm with a spectral full-width-at-half-maximum of ∼30 nm. With a 3 ML ZnS cladding layer, which also acts as a passivating and strain-compensating layer, the QDQWs acquired a ∼35% quantum yield of the QW emission. Blue and green electroluminescence (EL) was obtained from QDQW light-emitting devices with 3–4.5 ML CdSe QWs. It was found that as the peak blueshifted, the overall EL was increasingly dominated by defect state emission due to poor hole injection into the QDQWs. The weak EL was also attributed to strong field-induced charge separation resulting from the unique QDQW geometry, weakening the oscillator strength of optical transitions

Electroluminescence and phototrigger effect in single crystals of GaSxSe1-x alloys

International Nuclear Information System (INIS)

Kyazym-Zade, A. G.; Salmanov, V. M.; Mokhtari, A. G.; Dadashova, V. V.; Agaeva, A. A.

2008-01-01

The effects of switching and electroluminescence as well as the interrelation between these effects in single crystals of GaS x Se 1-x alloys are detected and studied. It is established that the threshold voltage for switching depends on temperature, resistivity, and composition of alloys, and also on the intensity and spectrum of photoactive light. As a result, a phototrigger effect is observed; this effect arises under irradiation with light from the fundamental-absorption region. Electroluminescence is observed in the subthreshold region of the current-voltage characteristic; the electroluminescence intensity decreases drastically to zero as the sample is switched from a high-resistivity state to a low-resistivity state. Experimental data indicating that the electroluminescence and the switching effect are based on the injection mechanism (as it takes place in other layered crystals of the III-V type) are reported

Electroluminescence of organic light-emitting diodes consisting of an undoped (pbi)2Ir(acac) phosphorescent layer

Science.gov (United States)

Lei, Xia; Yu, Junsheng; Zhao, Juan; Jiang, Yadong

2011-11-01

The electroluminescence (EL) characteristics of phosphorescent organic light-emitting diodes (OLEDs) with an undoped bis(1,2-dipheny1-1H-benzoimidazole) iridium (acetylacetonate) [(pbi)2Ir(acac)] emissive layer (EML) of various film thicknesses were studied. The results showed that the intensity of green light emission decreased rapidly with the increasing thickness of (pbi)2Ir(acac), which was relevant to the triplet excimer emission. It suggested that the concentration quenching of monomer emission in the undoped (pbi)2Ir(acac) film was mainly due to the formation of triplet excimer and partly due to the triplet-triplet annihilation (TTA) and triplet-polaron annihilation (TPA). A green OLED with a maximum luminance of 26,531 cd/m2, a current efficiency of 36.2 cd/A, and a power efficiency of 32.4 lm/W was obtained, when the triplet excimer emission was eliminated. Moreover, the white OLED with low efficiency roll-off was realized due to the broadened recombination zone and reduced quenching effects in the EML when no electron blocking layer was employed.

Hole-exciton interaction induced high field decay of magneto-electroluminescence in Alq{sub 3}-based organic light-emitting diodes at room temperature

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tingting; Holford, D. F.; Gu, Hang; Kreouzis, T. [Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Zhang, Sijie, E-mail: Sijie.zhang@scu.edu.cn, E-mail: w.gillin@qmul.ac.uk [College of Physical Science and Technology, Sichuan University, Chengdu 610064 (China); Gillin, W. P., E-mail: Sijie.zhang@scu.edu.cn, E-mail: w.gillin@qmul.ac.uk [Materials Research Institute and School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); College of Physical Science and Technology, Sichuan University, Chengdu 610064 (China)

2016-01-11

The magnetic field effects on the electroluminescence of aluminium tris-(8-hydroxyqinoline) (Alq{sub 3}) based organic light emitting diodes have been investigated by varying the electron/hole ratio in the emissive layer. Experimental results reveal that a negative high field effect in the magneto-electroluminescence (MEL) can be found in devices with very low triplet exciton concentration at room temperature. This suggests triplet-triplet annihilation cannot be used to explain the negative high field MEL in the Alq{sub 3} system. Our results suggest that hole-exciton interaction may be the origin of the negative high field MEL and also, in parallel with this interaction, there is also the more common positive high field process occurring which has been tentatively attributed to electron-exciton interactions. The competition between these different processes decides the final shape of the MEL at high fields.

Double peak spectra in spontaneous edge electroluminescence

Czech Academy of Sciences Publication Activity Database

Zavadil, Jiří; Žďánský, Karel

1993-01-01

Roč. 36, č. 11 (1993), s. 1623-1632 ISSN 0038-1101 R&D Projects: GA AV ČR IAA167108 Keywords : light emitting diodes * electroluminescence * optical waveguide theory Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.871, year: 1993

Electroluminescence and Photoluminescence from a Fluorescent Cobalt Porphyrin Grafted on Graphene Oxide

Science.gov (United States)

Janghouri, Mohammad

2017-10-01

A new graphene oxide-cobalt porphyrin (GO-CoTPP) hybrid material has been used as an emissive layer in organic light-emitting diodes (OLEDs). Devices with fundamental structure of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS, 45 nm)/polyvinylcarbazole (PVK):2-(4-biphenyl)-5-(4- t-butylphenyl)-1,3,4-oxadiazole (PBD):GO-CoTPP (70 nm)/1,3,5-tris( N-phenylbenzimidazol-2-yl)-benzene (TPBI, 20 nm)/Al (150 nm) were fabricated. A red electroluminescence (EL) was obtained from thin-film PVK:PBD:CoTPP at 70 nm thickness. When CoTPP was covalently grafted on graphene oxide (GO) sheets, near-white EL was obtained. The white emission, which was composed of bluish green and red, is attributed to electroplex formation at the GO-CoTPP/PBD interface. Such electroplex emission between electrons and holes is a reason for the low turn-on voltage of the GO-CoTPP-based OLED. Maximum luminance efficiency of 1.43 cd/A with Commission International de l'Eclairage coordinates of 0.33 and 0.40 was achieved at current of 0.02 mA and voltage of 14 V.

Visible-light electroluminescence in Mn-doped GaAs light-emitting diodes

International Nuclear Information System (INIS)

Nam Hai, Pham; Maruo, Daiki; Tanaka, Masaaki

2014-01-01

We observed visible-light electroluminescence (EL) due to d-d transitions in light-emitting diodes with Mn-doped GaAs layers (here, referred to as GaAs:Mn). Besides the band-gap emission of GaAs, the EL spectra show two peaks at 1.89 eV and 2.16 eV, which are exactly the same as 4 A 2 ( 4 F) → 4 T 1 ( 4 G) and 4 T 1 ( 4 G) → 6 A 1 ( 6 S) transitions of Mn atoms doped in ZnS. The temperature dependence and the current-density dependence are consistent with the characteristics of d-d transitions. We explain the observed EL spectra by the p-d hybridized orbitals of the Mn d electrons in GaAs

Photovoltaic and Electroluminescence Characters in Hybrid ZnO and Conjugated Polymer Bulk Heterojunction Devices

Institute of Scientific and Technical Information of China (English)

LIU Jun-Peng; QU Sheng-Chun; XU Ying; CHEN Yong-Hai; ZENG Xiang-Bo; WANG Zhi-Jie; ZHOU Hui-Ying; WANG Zhan-Guo

2007-01-01

We report electroluminescence in hybrid ZnO and conjugated polymer poly[2-methoxy-5-(3',7'-dimethyloctyloxy)-1,4-phenylenevinylene] (MDMO-PPV) bulk heterojunction photovoltaic cells. Photoluminescence quenching experimental results indicate that the ultrafast photoinduced electron transfer occurs from MDMO-PPV to ZnO under illumination. The ultrafast photoinduced electron transfer effect is induced because ZnO has an electron affinity about 1.2 eV greater than that of MDMO-PPV. Electron 'back transfer' can occur if the interfacial barrier between ZnO and MDMO-PPV can be overcome by applying a substantial electric field. Therefore, electroluminescence action due to the fact that the back transfer effect can be observed in the ZnO: MDMO-PPV devices since a forward bias is applied. The photovoltaic and electroluminescence actions in the same ZnO: MDMO-PPV device can be induced by different injection ways: photoinjection and electrical injection. The devices are expected to provide an opportunity for dual functionality devices with photovoltaic effect and electroluminescence character.

Preparation and characterizations of electroluminescent p-ZnO : N/n-ZnO : Ga/ITO thin films by spray pyrolysis method

Directory of Open Access Journals (Sweden)

C. Panatarani

2016-02-01

Full Text Available ZnO thin films were fabricated by spray pyrolysis (SP method with p-ZnO : N/n-ZnO:Ga/ITO structure. The X-ray results show that the deposited films have hexagonal wurtzite structure. The EDS results observed that the composition of Ga in ZnO:Ga and N in ZnO:N was 3.73% and 27.73% respectively. The photoluminescence (PL with excitation wave length of 260 nm shows that ZnO:Ga and ZnO:N films emitted UV emission at ∼393 and ∼388 nm, respectively and the films resistivity was 7.12 and 12.80 Ohm-cm respectively. The electroluminescence of the p-ZnO : N/n-ZnO:Ga/ITO structure was obtained by applying forward bias of 5 volt with 30 mA current, resulting in a 3.35 volt threshold bias with the peak electroluminescence in UV-blue range.

Density-matrix approach for the electroluminescence of molecules in a scanning tunneling microscope.

Science.gov (United States)

Tian, Guangjun; Liu, Ji-Cai; Luo, Yi

2011-04-29

The electroluminescence (EL) of molecules confined inside a nanocavity in the scanning tunneling microscope possesses many intriguing but unexplained features. We present here a general theoretical approach based on the density-matrix formalism to describe the EL from molecules near a metal surface induced by both electron tunneling and localized surface plasmon excitations simultaneously. It reveals the underlying physical mechanism for the external bias dependent EL. The important role played by the localized surface plasmon on the EL is highlighted. Calculations for porphyrin derivatives have reproduced corresponding experimental spectra and nicely explained the observed unusual large variation of emission spectral profiles. This general theoretical approach can find many applications in the design of molecular electronic and photonic devices.

Electroluminescence properties of Si MOS structures with incorporation of FeSi2 precipitates formed by iron implantation

International Nuclear Information System (INIS)

Chow, C.F.; Wong, S.P.; Gao, Y.; Ke, N.; Li, Q.; Cheung, W.Y.; Lourenco, M.A.; Homewood, K.P.

2005-01-01

Silicon MOS structures with FeSi 2 precipitates embedded in the MOS active region have been fabricated and the electroluminescence (EL) properties from these FeSi 2 -Si MOS structures were measured as a function of temperature from 80 K to 300 K. Clear EL signals were observed even at room temperature for samples prepared at appropriate processing conditions. The EL spectra consist of two peaks, one attributed to FeSi 2 and the other attributed to Si band edge emission. While the intensity of the FeSi 2 peak showed the usual thermal quenching behavior, the Si band edge emission showed the opposite trend with its intensity increased with increasing temperature. Details of the line shapes and their temperature dependence are analyzed and discussed

Spectrally resolved hyperfine interactions between polaron and nuclear spins in organic light emitting diodes: Magneto-electroluminescence studies

Energy Technology Data Exchange (ETDEWEB)

Crooker, S. A.; Kelley, M. R.; Martinez, N. J. D.; Nie, W.; Mohite, A.; Nayyar, I. H.; Tretiak, S.; Smith, D. L. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Liu, F.; Ruden, P. P. [University of Minnesota, Minneapolis, Minnesota 55455 (United States)

2014-10-13

We use spectrally resolved magneto-electroluminescence (EL) measurements to study the energy dependence of hyperfine interactions between polaron and nuclear spins in organic light-emitting diodes. Using layered devices that generate bright exciplex emission, we show that the increase in EL emission intensity I due to small applied magnetic fields of order 100 mT is markedly larger at the high-energy blue end of the EL spectrum (ΔI/I ∼ 11%) than at the low-energy red end (∼4%). Concurrently, the widths of the magneto-EL curves increase monotonically from blue to red, revealing an increasing hyperfine coupling between polarons and nuclei and directly providing insight into the energy-dependent spatial extent and localization of polarons.

An IBM-Compatible 640 X 200 Electroluminescent (EL) Display Monitor

Science.gov (United States)

Gullick, Paul; Schmachtenberg, Richard; Laakso, Carl

1986-05-01

An electroluminescent flat-panel display has been developed and recently introduced that fills any of the needs of the portable computer market. The display is very thin, yet rugged enough for the rigors of portability. It is highly integrated, and very reliable. It has the crisp and clear display image that is typical of high quality electroluminescent displays. The unit has a pixel matrix organization and pixel dimensions that are not only asthetically and ergonomically pleasing, but also make the display compatible with the most widely used software packages run on today's personal computers (Figure 1).

Near-infrared electroluminescence emission from an n-InN nanodots/p-Si heterojunction structure

International Nuclear Information System (INIS)

Wu Guoguang; Du Guotong; Gao Fubin; Shen Chunsheng; Li Wancheng; Wang Hui

2012-01-01

An n-InN nanodots/p-Si(1 1 1) heterojunction diode was fabricated by plasma-assisted molecular beam epitaxy. The device shows clear rectifying behaviour with a turn-on voltage of approximately 1.2 V at room temperature. The near-infrared electroluminescence (EL) can be observed under forward bias, which covers a wide wavelength range. In comparison with the photoluminescence spectra, the maximum of the EL spectra has a blueshift which is probably due to the size quantization effect of small-sized InN nanodots and their stronger contribution to the EL intensity. On the other hand, there is an obvious enhancement of the less dominant transitions on the short wavelength side of the EL spectra, which may arise from the recombination of the injected holes with the extremely high-density surface electrons of InN nanodots. (paper)

An inorganic electroluminescent device using calcium phosphate doped with Eu{sup 3+} as the luminescent layer

Energy Technology Data Exchange (ETDEWEB)

Koide, Takuhiro [Department of Chemistry and Chemical Engineering, Yamagata University, 4-3-16 Jonan, Yonezawa-shi, Yamagata 992-8510 (Japan); Ito, Michimasa [Tokai Rika Co. Ltd., 3-260 Toyota, Oguchi-cho, Niwa-gun, Aichi 480-0195 (Japan); Kawai, Takahiro [Department of Biochemical Engineering, Yamagata University, 4-3-16 Jonan, Yonezawa-shi, Yamagata 992-8510 (Japan); Matsushima, Yuta, E-mail: ymatsush@yz.yamagata-u.ac.jp [Department of Chemistry and Chemical Engineering, Yamagata University, 4-3-16 Jonan, Yonezawa-shi, Yamagata 992-8510 (Japan)

2013-03-20

Highlights: ► A thin film electroluminescent device was fabricated with a calcium phosphate as the light emitting layer. ► The light emitting layer was formed on the BaTiO{sub 3} disk by a spray pyrolysis method. ► Among the examined calcium phosphates, β-Ca{sub 3}(PO{sub 4}){sub 2}:Eu{sup 3+} showed the best photo- and electroluminescent properties. -- Abstract: In this work, the availability of calcium phosphates for the light emitting layer of a thin-film electroluminescent (TFEL) device was investigated. The goal of this work was to develop an electronic device with ordinary materials such as a calcium phosphate, the principal ingredient of the skeleton of the vertebrate. Compositions of 2CaO·P{sub 2}O{sub 5} (Ca{sub 2}P{sub 2}O{sub 7}), 3CaO·P{sub 2}O{sub 5} (Ca{sub 3}(PO{sub 4}){sub 2}) and 4CaO·P{sub 2}O{sub 5} (Ca{sub 4}O(PO{sub 4}){sub 2}) were examined as the candidates for the light emitting layer. Before composing the TFEL device, the photoluminescence (PL) properties of the three compositions were investigated in the powder form to evaluate the performance as the light emitting layer. Among the examined calcium phosphates, Eu-doped β-Ca{sub 3}(PO{sub 4}){sub 2} showed the best PL properties. It showed typical red-emission from Eu{sup 3+}. The PL intensity was enhanced with the heat-treatment temperature and the optimal temperature was 1250 °C. Then, a TFEL device was prepared by a spray pyrolysis method with the β-Ca{sub 3}(PO{sub 4}){sub 2}:Eu{sup 3+} phosphor layer on a BaTiO{sub 3} disk. The TFEL device exhibited the red emission originating in Eu{sup 3+} at 610 nm under applying alternating voltage. Different from the power sample, the intensity of EL decreased with the heat-treatment temperature from 1000 to 1250 °C. The deterioration of EL at the higher temperatures was attributed to chemical interaction between the phosphor layer and the BaTiO{sub 3} disk.

Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq3

Science.gov (United States)

Yuan, Chao; Guan, Min; Zhang, Yang; Li, Yiyang; Liu, Shuangjie; Zeng, Yiping

2017-08-01

In this work, the organic light-emitting diodes (OLEDs) based on Alq3 are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage-luminescence (I-V-L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq3). The MoO3 injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO3 injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The Vf is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between Vf caused by the MoO3 injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy)3 is 0.73 us/K.

Ultraviolet electroluminescence from n-ZnO/p-NiO heterojunction light-emitting diode

International Nuclear Information System (INIS)

Deng, R.; Yao, B.; Li, Y.F.; Xu, Y.; Li, J.C.; Li, B.H.; Zhang, Z.Z.; Zhang, L.G.; Zhao, H.F.; Shen, D.Z.

2013-01-01

The n-ZnO/p-NiO heterojunction was prepared by depositing a p-type NiO film on a c-plane sapphire by rf magnetron sputtering and then growing a n-type ZnO film on the NiO film by plasma-assisted molecular beam epitaxy. The heterojunction shows a diode-like rectification characteristic with a turn-on voltage of ∼3.6 V and emits UV light upon putting a forward bias. The intensity of the UV emission increases as injection current increases from 0.5 to 3.5 mA, but the wavelength of the UV emission decreases from 404 to 387 nm. It is demonstrated that the UV emission comes from near band-edge radiative recombination of electron and hole in the ZnO layer. The mechanism of the UV electroluminescence is discussed in the present work. - Highlights: ► The n-ZnO/p-NiO heterojunction was prepared by rf magnetron sputtering. ► The heterojunction shows a diode-like rectification characteristic with a turn-on voltage of ∼3.6 V. ► The heterojunction realizes UV EL emission with wavelength of 387 nm at the injection current of 3.5 mA.

Effect of γ-quanta on electroluminescent emitters with zinc sulfide luminophores

International Nuclear Information System (INIS)

Vershchagin, I.K.; Kokin, S.M.; Pautkina, A.V.

1993-01-01

The electroluminescent light sources used in data processing systems can operate under various conditions, particularly in the presence of a significant background radiation. In this work, the authors have investigated the effect of γ-irradiation on the main properties of electroluminescent emitters (ELE) prepared from polycrystalline luminophores of various grades. Such emitters are plane structures consisting of transparent and opaque electrodes and a layer of the luminophore distributed in the dielectric. The ELE were excited with a sinusoidal voltage (220 V; 0.4-1 kHz) at room temperature

Enhanced luminance for inorganic electroluminescent devices with a charged electret

Energy Technology Data Exchange (ETDEWEB)

Wang, Fang-Hsing, E-mail: fansen@dragon.nchu.edu.tw [Department of Electrical Engineering and Graduate Institute of Optoelectronic Engineering, National Chung Hsing University, Taichung 402, Taiwan, ROC (China); Chen, Kuo-Feng [Department of Electrical Engineering and Graduate Institute of Optoelectronic Engineering, National Chung Hsing University, Taichung 402, Taiwan, ROC (China); Display Technology Center/Industrial Technology Research Institute, Hsinchu 310, Taiwan, ROC (China); Chien, Yu-Han; Chang, Chin-Chia; Chuang, Meng-Ying [Display Technology Center/Industrial Technology Research Institute, Hsinchu 310, Taiwan, ROC (China)

2013-09-15

This work proposes a novel inorganic electroluminescent (IEL) device with an electric field built-in (EFBI) technique to reduce its driving voltage and enhance its luminance. The EFBI technique was performed by charging an electret comprising a silicon dioxide film at different temperatures (25–150 °C) in powder electroluminescent (PDEL) devices. The driving voltage of the EFBI-PDEL device decreased by 61.4 V (or 20.5%) under the brightness of 269 cd/m{sup 2}, and its brightness increased by 128 cd/m{sup 2} (or 47%) at ac 300 V. The efficiency of the EFBI-PDEL device significantly increased by 0.827 lm/W (or 45.5%) at ac 300 V. The proposed EFBI-PDEL device has advantages of a low-temperature process and low cost, and potential for large-area display applications. -- Highlights: • An electric-field built-in powder electroluminescent (EFBI-PDEL) device is proposed. • The EFBI technique is performed by charging an electrets. • The driving voltage of the EFBI-PDEL device decreased by 20.5%. • The brightness of the EFBI-PDEL device increased by 47%. • The efficiency of the EFBI-PDEL device increased by 45.5%.

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

Energy Technology Data Exchange (ETDEWEB)

Tregnago, G.; Fléchon, C.; Cacialli, F., E-mail: amateo@polymat.eu, E-mail: f.cacialli@ucl.ac.uk [Department of Physics and Astronomy and London Centre for Nanotechnology, University College London, London WC1E 6BT (United Kingdom); Choudhary, S. [School of Soft Matter Research, Freiburg Institute for Advanced Studies (FRIAS), Albert-Ludwigs-Universität Freiburg, Albertstraße 19, 79104 Freiburg (Germany); Institut für Organische Chemie und Biochemie, Albert-Ludwigs-Universität Freiburg, Albertstraße 21, 79104 Freiburg (Germany); Gozalvez, C. [POLYMAT, University of the Basque Country UPV/EHU, Avenida de Tolosa 72, E-20018 Donostia-San Sebastian (Spain); Mateo-Alonso, A., E-mail: amateo@polymat.eu, E-mail: f.cacialli@ucl.ac.uk [POLYMAT, University of the Basque Country UPV/EHU, Avenida de Tolosa 72, E-20018 Donostia-San Sebastian (Spain); Ikerbasque, Basque Foundation for Science, Bilbao (Spain)

2014-10-06

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ∼1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ∼1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

International Nuclear Information System (INIS)

Tregnago, G.; Fléchon, C.; Cacialli, F.; Choudhary, S.; Gozalvez, C.; Mateo-Alonso, A.

2014-01-01

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ∼1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ∼1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Virtually pure near-infrared electroluminescence from exciplexes at polyfluorene/hexaazatrinaphthylene interfaces

Science.gov (United States)

Tregnago, G.; Fléchon, C.; Choudhary, S.; Gozalvez, C.; Mateo-Alonso, A.; Cacialli, F.

2014-10-01

Electronic processes at the heterojunction between chemically different organic semiconductors are of special significance for devices such as light-emitting diodes (LEDs) and photovoltaic diodes. Here, we report the formation of an exciplex state at the heterojunction of an electron-transporting material, a functionalized hexaazatrinaphthylene, and a hole-transporting material, poly(9,9-dioctylfluorene-alt-N-(4-butylphenyl)diphenylamine) (TFB). The energetics of the exciplex state leads to a spectral shift of ˜1 eV between the exciton and the exciplex peak energies (at 2.58 eV and 1.58 eV, respectively). LEDs incorporating such bulk heterojunctions display complete quenching of the exciton luminescence, and a nearly pure near-infrared electroluminescence arising from the exciplex (at ˜1.52 eV) with >98% of the emission at wavelengths above 700 nm at any operational voltage.

Electroluminescence Properties of IrQ(ppy)2 Dual-Emitter Organometallic Compound in Organic Light-Emitting Devices

Science.gov (United States)

Ciobotaru, Constantin Claudiu; Polosan, Silviu; Ciobotaru, Iulia Corina

2018-02-01

This paper reports the influence of the charge carrier mobility on the electroluminescent properties of a dual-emitter organometallic compound dispersed in two conjugated organic small-molecule host materials and embedded in organic light-emitting devices (OLEDs). The electroluminescent processes in OLEDs are strongly influenced by the host-guest interaction. The charge carrier mobility in the host material plays an important role in the electroluminescent processes but also depends on the triplet-triplet interaction with the organometallic compound. The low charge carrier mobility in 4,4'-bis( N-carbazolyl)-1,1'-biphenyl (CBP) host material reduces the electroluminescent processes, but they are slightly enhanced by the triplet-triplet exothermic charge transfer. The higher charge carrier mobility in the case of N, N'-bis(3-methylphenyl)- N, N'-diphenylbenzidine (TPD) host material influences the electroluminescent processes by the endothermic energy transfer at room temperature, which facilitates the triplet-triplet harvesting in the host-guest system. The excitation is transferred to the guest molecules by triplet-triplet interaction as a Dexter transfer, which occurs by endothermic transfer from the triplet exciton in the host to the triplet exciton in the guest.

Room Temperature Direct Band Gap Emission from Ge p-i-n Heterojunction Photodiodes

Directory of Open Access Journals (Sweden)

E. Kasper

2012-01-01

Full Text Available Room temperature direct band gap emission is observed for Si-substrate-based Ge p-i-n heterojunction photodiode structures operated under forward bias. Comparisons of electroluminescence with photoluminescence spectra allow separating emission from intrinsic Ge (0.8 eV and highly doped Ge (0.73 eV. Electroluminescence stems from carrier injection into the intrinsic layer, whereas photoluminescence originates from the highly n-doped top layer because the exciting visible laser wavelength is strongly absorbed in Ge. High doping levels led to an apparent band gap narrowing from carrier-impurity interaction. The emission shifts to higher wavelengths with increasing current level which is explained by device heating. The heterostructure layer sequence and the light emitting device are similar to earlier presented photodetectors. This is an important aspect for monolithic integration of silicon microelectronics and silicon photonics.

Synthesis, structures and electroluminescence properties of CdS:In/Si nanoheterostructure array

Energy Technology Data Exchange (ETDEWEB)

Yan, Ling Ling; Cai, Hong Xin; Chen, Liang [Henan Polytechnic University, School of Physics and Electronic Information Engineering, Jiaozuo (China)

2017-10-15

An In-doped CdS/Si nanoheterojunction (CdS:In/Si-NPA) is prepared by depositing an In-doped CdS thin film onto a Si nanoporous pillar array (Si-NPA) via a successive ionic layer adsorption and reaction method. Based on the measured J-V characteristic curve, the nanoheterojunction exhibits a good rectifying behavior with a low forward turn-on voltage (2.2 V), a small leakage current density (0.5 mA/cm{sup 2} at - 3 V) and a high reverse breakdown voltage (> 8 V). The electroluminescence (EL) measurements reveal that a broadband emerges between 400 and 700 nm, and this band is confirmed as a white light emission based on the value of the chromaticity coordinate. The EL properties, including the CIE chromaticity coordinates, Colour Rendering Index and correlated color temperature, can be tuned by the applied voltage. The generation mechanism of the EL can be well interpreted depending on the energy band structure of CdS:In/Si-NPA. The green band should be attributed to the band-edge emission of CdS and the yellow emission may be related to Cd interstitial. These results highlight the potential of CdS:In/Si-NPA as a light source for future white light emitting devices. (orig.)

STM-electroluminescence from clustered C3N4 nanodomains synthesized via green chemistry process.

Science.gov (United States)

Andrade, E P; Costa, B B A; Chaves, C R; de Paula, A M; Cury, L A; Malachias, A; Safar, G A M

2018-01-01

A Scanning Tunneling Microscopy/Spectroscopy (STM/STS) and synchrotron X-ray diffraction study on clustered C 3 N 4 nanoparticles (nanoflakes) is conducted on green-chemistry synthesized samples obtained from chitosan through high power sonication. Morphological aspects and the electronic characteristics are investigated. The observed bandgap of the nanoflakes reveals the presence of different phases in the material. Combining STM morphology, STS spectra and X-ray diffraction (XRD) results one finds that the most abundant phase is graphitic C 3 N 4 . A high density of defects is inferred from the XRD measurements. Additionally, STM-electroluminescence (STMEL) is detected in C 3 N 4 nanoflakes deposited on a gold substrate. The tunneling current creates photons that are three times more energetic than the tunneling electrons of the STM sample. We ponder about the two most probable models to explain the observed photon emission energy: either a nonlinear optical phenomenon or a localized state emission. Copyright © 2017 Elsevier B.V. All rights reserved.

Charge carriers at organic heterojunction interface: Exciplex emission or electroplex emission?

Science.gov (United States)

Yang, Shengyi; Zhang, Xiulong; Hou, Yanbing; Deng, Zhenbo; Xu, Xurong

2007-05-01

We report the electroluminescence (EL) of organic heterojunction devices based on N ,N'-diphenyl-N ,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4',-diamine (TPD) and 2-(4'-biphenyl)-5-(4″-tert-butylphenyl)-1,3,4-oxadiazole (PBD). Besides monomolecular emissions from TPD, there are two additional EL peaks at around 460 and 480nm from the bilayer device indium tin oxide (ITO)/TPD(100nm )/PBD(45nm)/Al. Our experimental data confirmed that the EL emission maximized at around 460nm is from electroplex as the result of charge carriers cross recombination at the TPD/PBD interface and the EL emission maximized at around 480nm originates from (TPD*PBD)-type exciplex.

Electroluminescence efficiencies of erbium in silicon-based hosts

Energy Technology Data Exchange (ETDEWEB)

Cueff, Sébastien, E-mail: sebastien-cueff@brown.edu, E-mail: christophe.labbe@ensicaen.fr [Centre de Recherche sur les Ions, les Matériaux et la Photonique (CIMAP), UMR 6252 CNRS/CEA/Ensicaen/UCBN, Caen 14050 (France); School of Engineering, Brown University, Providence, Rhode Island 02912 (United States); Manel Ramírez, Joan; Berencén, Yonder; Garrido, Blas [MIND-IN2UB, Department Electrònica, Universitat de Barcelona, Martí i Franquès 1, Barcelona 08028 (Spain); Kurvits, Jonathan A.; Zia, Rashid [School of Engineering, Brown University, Providence, Rhode Island 02912 (United States); Department of Physics, Brown University, Providence, Rhode Island 02912 (United States); Rizk, Richard; Labbé, Christophe, E-mail: sebastien-cueff@brown.edu, E-mail: christophe.labbe@ensicaen.fr [Centre de Recherche sur les Ions, les Matériaux et la Photonique (CIMAP), UMR 6252 CNRS/CEA/Ensicaen/UCBN, Caen 14050 (France)

2013-11-04

We report on room-temperature 1.5 μm electroluminescence from trivalent erbium (Er{sup 3+}) ions embedded in three different CMOS-compatible silicon-based hosts: SiO{sub 2}, Si{sub 3}N{sub 4}, and SiN{sub x}. We show that although the insertion of either nitrogen or excess silicon helps enhance electrical conduction and reduce the onset voltage for electroluminescence, it drastically decreases the external quantum efficiency of Er{sup 3+} ions from 2% in SiO{sub 2} to 0.001% and 0.0004% in SiN{sub x} and Si{sub 3}N{sub 4}, respectively. Furthermore, we present strong evidence that hot carrier injection is significantly more efficient than defect-assisted conduction for the electrical excitation of Er{sup 3+} ions. These results suggest strategies to optimize the engineering of on-chip electrically excited silicon-based nanophotonic light sources.

Electroluminescence of erbium in Al/α-Si:H(Er)/p-c-Si/Al structure

International Nuclear Information System (INIS)

Kon'kov, I.O.; Kuznetsov, A.N.; Pak, P.E.; Terukov, E.I.; Granitsyna, L.S.

2001-01-01

It is informed for the first time on the observation of the erbium intensive electroluminescence from the amorphous hydrated silicon layer by application of the Al/α-Si:H(Er)/p-c-Si/Al structure in the direct shift mode. The above structure is the n-p-heterostructure with the barrier values of 0.3-0.4 eV for the electrons and 0.9-1.1 eV for the holes. The electroluminescence efficiency is evaluated at the level ∼ 2 x 10 -5 . The electroluminescence effect in the Al/α-Si:H(Er)/p-c-Si/Al structure is connected with the hole tunneling from the crystal silicon by the amorphous silicon localized states with the subsequent release into the valent zone [ru

Electroplex emission at PVK/Bphen interface for application in white organic light-emitting diodes

International Nuclear Information System (INIS)

Wen Liang; Li Fushan; Xie Jiangxing; Wu Chaoxing; Zheng Yong; Chen Dongling; Xu Sheng; Guo Tailiang; Qu Bo; Chen Zhijian; Gong Qihuang

2011-01-01

White organic light-emitting diode (WOLED) with a structure of ITO/poly(N-vinylcarbazole) (PVK)/4,7-diphenyl-1, 10-phenanthroline (Bphen)/tris(8-hydroxyquinoline)aluminum (Alq 3 )/LiF/Al has been fabricated via the thermal evaporation technique. The electroluminescence (EL) spectrum of the as-fabricated WOLED covers from 380 to 700 nm of the visible light region with a wide blue emission from PVK and an interesting new red emission. The red emission at 613 nm in EL spectra of the WOLED was attributed to electroplex emission at PVK/Bphen interface since it was not observed in photoluminescence spectra. The WOLED showed a Commission International De l'Eclairage coordinate of (0.31, 0.32), which is very close to the standard white coordinate (0.33, 0.33). - Highlights: → A white organic light-emitting diode was fabricated by vacuum deposition. → A new red emission at 613 nm was observed in the electroluminescence spectra. → Red emission comes from electroplex instead of exciplex at PVK/Bphen interface. → The device has a CIE coordinate of (0.31, 0.32).

Carbon-electroluminescence: An organic approach to lighting

Science.gov (United States)

Kumari, Sonali; Chaudhary, Tarun; Chandran, Vivek; Lokeshwari, M.; Shastry, K.

2018-05-01

Over the recent years, quantum dots have garnered massive following and peaked in interest among the scientific community due to their versatility, exotic properties, ease of preparation and low cost. As the demand for faster, reliable and energy efficient electronic devices intensifies, extra emphasis is laid on the development of smart materials capable of satiating this need. Electroluminescent organic quantum dots have emerged as one of the prime contenders in addressing the ecological, economic and technological constraints. Application of such luminescent nanoparticles as fluorescent light converters in LEDs is touted as one of the reliable and easiest avenues in realizing and developing newer energy efficient technologies for the next millennia. One promising candidate is zig-zag graphene quantum dots, which exhibits high electro-luminescence due to a phenomenon known as quantum confinement (where size of the nano-particle is of the same order or less than that of Bohr exciton radius). In this paper, we aim to provide a review of past and present research in the synthesis and development of luminescence using organic quantum dots.

Functional electronic screen printing – electroluminescent smart fabric watch

OpenAIRE

de Vos, Marc; Torah, Russel; Beeby, Steve; Tudor, John

2013-01-01

Motivation for screen printed smart fabrics.Introduce functional electronic screen printing on fabrics.Printed smart fabric watch design.Printing process for electroluminescent watch.Demonstration video.Conclusions and further work.Examples of other screen printed smart fabrics.

Flexible powder electroluminescent device on silver nanowire electrode

International Nuclear Information System (INIS)

Park, K.W.; Jeong, H.S.; Park, J.H.; Deressa, G.; Jeong, Y.T.; Lim, K.T.; Park, J.H.; Lee, S.H.; Kim, J.S.

2015-01-01

We have demonstrated the flexible AC powder electroluminescent device based on Ag nanowire electrode. The Ag nanowire electrode showed the nanowire morphology of 20 nm in diameter and 15 μm in length, the transmittance of 87%, and the sheet resistance of 50 Ω/sq, and the higher flexibility than the conventional ITO substrate. The electroluminescence spectra of the Ag nanowire-based device in all frequency and voltage ranges were almost similar with the ITO-based device. In comparison with the ITO-based device, the luminous efficiency of the Ag nanowire-based device was almost same as 1.53 lm/W. - Highlights: • Flexibility of Ag NW substrate was higher than ITO substrate. • EL intensity of Ag NW-based EL device was almost similar with ITO-based EL device. • Charge density and turn-on voltage of Ag NW-based EL device were a little larger than ITO-based EL device

Flexible powder electroluminescent device on silver nanowire electrode

Energy Technology Data Exchange (ETDEWEB)

Park, K.W.; Jeong, H.S.; Park, J.H.; Deressa, G.; Jeong, Y.T.; Lim, K.T. [Department of Display Science and Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Park, J.H. [AIDEN company, Cheongju-si 361-911 (Korea, Republic of); Lee, S.H. [R& D Business Lab, Hyosung Corporation, Anyang 431-080 (Korea, Republic of); Kim, J.S., E-mail: jsukim@pknu.ac.kr [Department of Display Science and Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

2015-09-15

We have demonstrated the flexible AC powder electroluminescent device based on Ag nanowire electrode. The Ag nanowire electrode showed the nanowire morphology of 20 nm in diameter and 15 μm in length, the transmittance of 87%, and the sheet resistance of 50 Ω/sq, and the higher flexibility than the conventional ITO substrate. The electroluminescence spectra of the Ag nanowire-based device in all frequency and voltage ranges were almost similar with the ITO-based device. In comparison with the ITO-based device, the luminous efficiency of the Ag nanowire-based device was almost same as 1.53 lm/W. - Highlights: • Flexibility of Ag NW substrate was higher than ITO substrate. • EL intensity of Ag NW-based EL device was almost similar with ITO-based EL device. • Charge density and turn-on voltage of Ag NW-based EL device were a little larger than ITO-based EL device.

How to restrain electroplex emission and enhance red emission intensity of Eu 3+ complex?

Science.gov (United States)

Zhang, Fujun; Zhao, Suling; Xu, Zheng; Huang, Jinzhao; Yuan, Guancai; Li, Yuan; Wang, Yong; Xu, Xurong

2007-11-01

The electroluminescence (EL) of lanthanide complex profits from the intramolecular energy transfer from the triplet state of ligand to Ln (III) ions, but electroplex emission between ligand and host material may occur when the energy transfer is inefficient. The electroplex emission is completely restrained when 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7,-tetramethyljulolidy-9-enyl)-4Hpyran (DCJTB) and Eu(o-BBA)3(phen) are co-doped in poly (N-vinycarbzaole) (PVK). There are great spectra overlapping between electroplex emission and the excitation of DCJTB. The chromaticity coordinates of EL of co-doped device is kept constant (x = 0.55, y = 0.37) under different driving voltage.

Photo- and electroluminescence of undoped and rare earth doped ZnO electroluminors

International Nuclear Information System (INIS)

Bhushan, S.; Pandey, A.N.; Kaza, B.R.

1977-01-01

A series of undoped and rare earth (Dy, Yb, Nd, Pr, Gd, La, Sm and Er) doped ZnO electroluminors have been prepared and their photo- (PL) and electroluminescence (EL) spectra at different concentrations of rare earth ions have been investigated. PL and EL spectra of undoped electroluminescence consist of three peaks. Due to the addition of the rare earth ions these peaks are shifted either to the longer or to the shorter wavelength side. The intensities are also either decreased or increased. Experimental results favour the donor-accepted model for this system. (Auth.)

Supporting Information Blue and White light electroluminescence in ...

Indian Academy of Sciences (India)

Administrator

Blue and White light electroluminescence in a multilayer OLED using a new Aluminium complex. Pabitra K. Nayak a. , Neeraj Agarwal a. , Farman Ali a. , Meghan P. Patankar b. , K. L.. Narasimhan b. *, N. Periasamy a. *. 1. Department of Chemical Sciences,. 2. Department of Condensed Matter Physics and. Materials ...

Electroluminescence from graphene excited by electron tunneling

International Nuclear Information System (INIS)

Beams, Ryan; Bharadwaj, Palash; Novotny, Lukas

2014-01-01

We use low-energy electron tunneling to excite electroluminescence in single layer graphene. Electrons are injected locally using a scanning tunneling microscope and the luminescence is analyzed using a wide-angle optical imaging system. The luminescence can be switched on and off by inverting the tip–sample bias voltage. The observed luminescence is explained in terms of a hot luminescence mechanism. (paper)

Stimulated Emission from InAs (GaAs Monolayers Stacks Embedded in Al0.33Ga0.67As Ective Region

Directory of Open Access Journals (Sweden)

Dusan Pudis

2002-01-01

Full Text Available Our study is focused on the optical and electronic properties of InAs (GaAs monolayers embedded in Al0.33GA0.67As barrier layers investigated by temperature dependencies of electroluminescence spectra. The experimental results obtained from low temperature electroluminescence measurements of InAs (GaAs/Al0.33GA0.67As revealed the excellent emission spectra in the visib le range 630-690 nm. The stimulated emission from these structures across their cleavage planes has been observed at low  temperatures what is highly interesting for potential device applications.

Synthesis and electroluminescent properties of anthracene derivatives containing electron-withdrawing oxide moieties

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jhin-yeong; Na, Eun Jae; Park, Soo Na [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Lee, Seok Jae [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Kim, Young Kwan, E-mail: kimyk@wow.hongik.ac.kr [Department of Information Display, Hongik University, Seoul, 121-791 (Korea, Republic of); Yoon, Seung Soo, E-mail: ssyoon@skku.edu [Department of Chemistry, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of)

2014-10-15

Highlights: • Blue fluorescent material is important for application in full-color displays. • We have synthesized emitters based on anthracene connected with oxide moieties. • 1C shows a highly efficient blue EL emission due to electron-injection property. - Abstract: A series of new blue-emitting materials: (4-(10-(naphthalen-2-yl)anthracen-9-yl)phenyl)(phenyl)methanone (1); 9-(naphthalen-2-yl)-10-(4-((diphenyl)phosphine oxide)phenyl)anthracene (2); 9-(naphthalen-2-yl)-10-(4-(phenylsulfonyl)phenyl)anthracene (3) were designed and synthesized via Suzuki cross-coupling reaction. Multilayer OLEDs were fabricated in the following sequence: ITO (180 nm)/NPB (50 nm)/blue materials 1–3 (30 nm)/TPBi (15 nm)/Liq (2 nm)/Al (100 nm). All devices showed the efficient blue EL emissions. In particular, the device using 1 as an emitter exhibited efficient blue electroluminescent properties with a maximum luminous, power, external quantum efficiency and CIE coordinates of 0.36 cd/A, 0.90 lm/W, 0.55% at 20 mA/cm{sup 2} and (x = 0.16, y = 0.20) at 10.0 V, respectively.

White light emission of monolithic InGaN/GaN grown on morphology-controlled, nanostructured GaN templates

Science.gov (United States)

Song, Keun Man; Kim, Do-Hyun; Kim, Jong-Min; Cho, Chu-Young; Choi, Jehyuk; Kim, Kahee; Park, Jinsup; Kim, Hogyoug

2017-06-01

We demonstrated an InGaN/GaN-based, monolithic, white light-emitting diode (LED) without phosphors by using morphology-controlled active layers formed on multi-facet GaN templates containing polar and semipolar surfaces. The nanostructured surface morphology was controlled by changing the growth time, and distinct multiple photoluminescence peaks were observed at 360, 460, and 560 nm; these features were caused by InGaN/GaN-based multiple quantum wells (MQWs) on the nanostructured facets. The origin of each multi-peak was related to the different indium (In) compositions in the different planes of the quantum wells grown on the nanostructured GaN. The emitting units of MQWs in the LED structures were continuously connected, which is different from other GaN-based nanorod or nanowire LEDs. Therefore, the suggested structure had a larger active area. From the electroluminescence spectrum of the fabricated LED, monolithic white light emission with CIE color coordinates of x = 0.306 and y = 0.333 was achieved via multi-facet control combined with morphology control of the metal organic chemical vapor deposition-selective area growth of InGaN/GaN MQWs.

White light emission of monolithic InGaN/GaN grown on morphology-controlled, nanostructured GaN templates.

Science.gov (United States)

Song, Keun Man; Kim, Do-Hyun; Kim, Jong-Min; Cho, Chu-Young; Choi, Jehyuk; Kim, Kahee; Park, Jinsup; Kim, Hogyoug

2017-06-02

We demonstrated an InGaN/GaN-based, monolithic, white light-emitting diode (LED) without phosphors by using morphology-controlled active layers formed on multi-facet GaN templates containing polar and semipolar surfaces. The nanostructured surface morphology was controlled by changing the growth time, and distinct multiple photoluminescence peaks were observed at 360, 460, and 560 nm; these features were caused by InGaN/GaN-based multiple quantum wells (MQWs) on the nanostructured facets. The origin of each multi-peak was related to the different indium (In) compositions in the different planes of the quantum wells grown on the nanostructured GaN. The emitting units of MQWs in the LED structures were continuously connected, which is different from other GaN-based nanorod or nanowire LEDs. Therefore, the suggested structure had a larger active area. From the electroluminescence spectrum of the fabricated LED, monolithic white light emission with CIE color coordinates of x = 0.306 and y = 0.333 was achieved via multi-facet control combined with morphology control of the metal organic chemical vapor deposition-selective area growth of InGaN/GaN MQWs.

Influence of annealing temperature on erbium ion electroluminescence in Si : (Er,O) diodes with (111) substrate orientation

CERN Document Server

Sobolev, N A; Nikolaev, Y A

2001-01-01

A study has been made of the influence of temperature of the second annealing that promotes formation of optically and electrically active centers o the erbium ion electroluminescence at lambda approx = 1.54 mu m wavelength in (111) Si : (Er,O) diodes. Doping has been performed by implantation of erbium and oxygen ions at 2.0, 1.6 MeV and 0.28, 0.22 MeV energies and 3 x 10 sup 1 sup 4 cm sup - sup 2 and 3 x 10 sup 1 sup 5 cm sup - sup 2 doses, respectively. The room temperature electroluminescence intensity under the breakdown regime increases with increasing annealing temperature from 700 to 950 deg C. After annealing in the range of 975-1100 deg C, erbium electroluminescence under the breakdown regime is not observed due to appearance of microplasmas. The injection electroluminescence intensity at 80 K decreases with increasing temperature from 700 to 1100 deg C

Efficient electroluminescence from a perylenediimide fluorophore obtained from a simple solution processed OLED

International Nuclear Information System (INIS)

Cespedes-Guirao, F J; Fernandez-Lazaro, F; Sastre-Santos, A; Garcia-Santamaria, S; Bolink, H J

2009-01-01

Simple solution processed organic light emitting diodes are used to screen the performance of two types of highly efficient, narrow band red emitting fluorescent perylenediimides (PDIs). PDIs substituted at the diimide positions seem to form aggregates in the thin film architecture as evidenced by the shifted electroluminescent spectrum. When substituted on the bay position and when used both as the emitting and the electron transporting specie, bright electroluminescence with a narrow width around 610 nm reaching 500 cd m -2 at moderate voltages was observed, demonstrating the usefulness of these fluorophores for OLED applications.

Single-crystal structure, photophysical characteristics and electroluminescent properties of bis(2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate)zinc

International Nuclear Information System (INIS)

Xu Huixia; Yue, Yan; Wang Hua; Chen Liuqing; Hao Yuying; Xu Bingshe

2012-01-01

In this paper, a zinc (II) complex of Zn 2 (4-tfmBTZ) 4 (4-tfmBTZ=2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate) was reported. Via combination of experimental and theoretical approaches, its molecular structure, photophysical characteristics, electronic structure and electroluminescent properties were investigated. The results indicate that Zn 2 (4-tfmBTZ) 4 exists as five-coordinate geometric structure and two zinc atoms are bridged by oxygen atoms. The intense absorption band was located at 404 nm, which mainly originate from the transition HOMO−1 to LUMO+2. The blue-light emission was observed in tetrahydrofuran solution and thin film. White-light emission with four emission peaks was observed with CIE coordinate of (0.29, 0.33) and a higher CRI of 85.1 by fabricating bilayer device using Zn 2 (4-tfmBTZ) 4 as electron-transport and NPB as hole-transport material. - Highlights: ► The single-crystal and electronic structures of Zn 2 (4-tfmBTZ) 4 . ► The multicolor emission of Zn 2 (4-tfmBTZ) 4 were realized by the simple devices. ► White OLED is achieved with particularly high color rending index (CRI) by the emission of Zn 2 (4-tfmBTZ) 4 .

Automatic Detection of Inactive Solar Cell Cracks in Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2017-01-01

We propose an algorithm for automatic determination of the electroluminescence (EL) signal threshold level corresponding to inactive solar cell cracks, resulting from their disconnection from the electrical circuit of the cell. The method enables automatic quantification of the cell crack size...

Study of the electroluminescence of highly stereoregular poly(N-pentenyl-carbazole) for blue and white OLEDs

Science.gov (United States)

Liguori, R.; Botta, A.; Pragliola, S.; Rubino, A.; Venditto, V.; Velardo, A.; Aprano, S.; Maglione, M. G.; Prontera, C. T.; De Girolamo Del Mauro, A.; Fasolino, T.; Minarini, C.

2017-06-01

The electroluminescence (EL) of isotactic and syndiotactic poly(N-pentenyl-carbazole) (PPK), achieved by coordination polymerization, is studied in order to investigate the interrelation between the polymer tacticity and their physical-chemical properties. The use of these polymers in organic light-emitting diode (OLED) fabrication is also explored. Thermal and x-ray diffraction analyses of PPKs show that the isotactic stereoisomer is semicrystalline, whereas the syndiotactic one is amorphous. Optical analysis of both stereoisomers, carried out on film samples, reveals the presence of two different excimers: ‘sandwich-like’ and ‘partially overlapping’. Nevertheless, the emission intensity ratio between ‘sandwich-like’ and ‘partially overlapping’ excimers is higher in the isotactic than in the syndiotactic stereoisomer. Using the synthesized polymers as OLED emitting layers, the influence of the polymer tacticity on the EL properties of the device is highlighted. In detail, while blue OLEDs are obtained by using the syndiotactic stereoisomer, OLEDs with a multilayer structure fabricated with the isotactic stereoisomer emit white light. The contribution of three different emissions (fluorescence, phosphorescence and electromer emissions) with comparable intensities to the detected white light is discussed.

Thin film electroluminescent cells on the basis of Ce-doped CaGa2S4 and SrGa2S4 prepared by flash evaporation method

International Nuclear Information System (INIS)

Gambarov, E.; Bayramov, A.; Kato, A.; Iida, S.

2006-01-01

Ce-doped CaGa 2 S 4 and SrGa 2 S 4 thin film electroluminescent (TFEL) devices were prepared for the first time on the basis of films deposited by flash evaporation method. Significant crystallization, stoichiometry improvement of the films and increase of photoluminescence intensity were found after annealing in H 2 S and O 2 gas stream. EL spectra of the cells exhibited the characteristic double-band emission similar to that seen for Ce 3+ activated CaGa 2 S 4 and SrGa 2 S 4 films under photon excitation. Applied voltage and frequency dependences of the electroluminescence were studied. Low voltage operation as low as 20 V was observed for these cells. Luminance of about 4 cd/m 2 at 100 V operating voltage with 2.5 kHz frequency was achieved for the TFEL cell with films annealed in O 2 gas stream. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Efficient light emitting devices based on phosphorescent partially doped emissive layers

KAUST Repository

Yang, Xiaohui

2013-05-29

We report efficient organic light emitting devices employing an ultrathin phosphor emissive layer. The electroluminescent spectra of these devices can be tuned by introducing a low-energy emitting phosphor layer into the emission zone. Devices with the emissive layer consisting of multiple platinum-complex/spacer layer cells show a peak external quantum efficiency of 18.1%, which is among the best EQE values for platinum-complex based light emitting devices. Devices with an ultrathin phosphor emissive layer show stronger luminance decay with the operating time compared to the counterpart devices having a host-guest emissive layer.

Automatic Detection of Inactive Solar Cell Cracks in Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2017-01-01

We propose an algorithm for automatic determination of the electroluminescence (EL) signal threshold level corresponding to inactive solar cell cracks, resulting from their disconnection from the electrical circuit of the cell. The method enables automatic quantification of the cell crack size an...

Electroplex emission of the blend film of PVK and DPVBi

Science.gov (United States)

Li, Junming; Xu, Zheng; Zhang, Fujun; Zhao, Suling; Song, Dandan; Zhu, Haina; Song, Jinglu; Wang, Yongsheng; Xu, Xurong

2010-04-01

Influences of electric fields on the emission from organic light-emitting diodes (OLEDs) based on poly(N-vinylcarbazole) (PVK) and 4‧-bis(2-2diphenylvinyl)-1,1‧-biphenyl (DPVBi) as the active emission layer are studied. Electroluminescence (EL) spectra of PVK:DPVBi (1:1 w/w) films show one new emission peak locating at 640 nm compared with its photoluminescence (PL) spectra. There may be exists an electroplex emission between the PVK and DPVBi under high electric field strength. The emission intensity of peaking at 640 nm strongly depends on the driving voltage, and the ratio of electroplex emission intensity to exciton emission intensity (Ielectroplex/Iexciton) increases with the increase of driving voltage.

Electroluminescence and photosensitivity spectra of organic diode structures based on zinc complexes

Science.gov (United States)

Kaplunov, M. G.; Krasnikova, S. S.; Nikitenko, S. L.; Yakushchenko, I. K.

2017-01-01

Devices based on zinc complexes with sulphanylaminosubstituted ligands are characterized by dual function - electroluminescence (EL) and photosensitivity. Both EL and photosensitivity are associated with the formation of exciplexes.

Enhancement of Electroluminescence (EL) image measurements for failure quantification methods

DEFF Research Database (Denmark)

Parikh, Harsh; Spataru, Sergiu; Sera, Dezso

2018-01-01

Enhanced quality images are necessary for EL image analysis and failure quantification. A method is proposed which determines image quality in terms of more accurate failure detection of solar panels through electroluminescence (EL) imaging technique. The goal of the paper is to determine the most...

Quantifying Solar Cell Cracks in Photovoltaic Modules by Electroluminescence Imaging

DEFF Research Database (Denmark)

Spataru, Sergiu; Hacke, Peter; Sera, Dezso

2015-01-01

This article proposes a method for quantifying the percentage of partially and totally disconnected solar cell cracks by analyzing electroluminescence images of the photovoltaic module taken under high- and low-current forward bias. The method is based on the analysis of the module’s electrolumin...

Electroluminescence and photosensitivity spectra of organic diode structures based on zinc complexes

International Nuclear Information System (INIS)

Kaplunov, M.G.; Krasnikova, S.S.; Nikitenko, S.L.; Yakushchenko, I.K.

2017-01-01

Devices based on zinc complexes with sulphanylaminosubstituted ligands are characterized by dual function – electroluminescence (EL) and photosensitivity. Both EL and photosensitivity are associated with the formation of exciplexes.

Tunable magneto-conductance and magneto-electroluminescence in polymer light-emitting electrochemical planar devices

Energy Technology Data Exchange (ETDEWEB)

Geng, R.; Mayhew, N. T.; Nguyen, T. D., E-mail: ngtho@uga.edu [Department of Physics and Astronomy, University of Georgia, Athens, Georgia 30602 (United States)

2013-12-09

We report studies of magneto-conductance (MC) and magneto-electroluminescence (MEL) in polymer light-emitting electrochemical planar devices using “super-yellow” poly-(phenylene vinylene). We observed consistent negative MC while MEL becomes positive when electroluminescence quantum efficiency (ELQE) increases. At an optimal ELQE, the MC has a much narrower width than the MEL, indicating that the MC and MEL do not share a common origin. However, MC reverses and has the same width as MEL when exposed to a threshold laser power. We show that the e-h pair model can explain the positive MEL and MC while the negative MC can be explained by the bipolaron model.

Tunable magneto-conductance and magneto-electroluminescence in polymer light-emitting electrochemical planar devices

International Nuclear Information System (INIS)

Geng, R.; Mayhew, N. T.; Nguyen, T. D.

2013-01-01

We report studies of magneto-conductance (MC) and magneto-electroluminescence (MEL) in polymer light-emitting electrochemical planar devices using “super-yellow” poly-(phenylene vinylene). We observed consistent negative MC while MEL becomes positive when electroluminescence quantum efficiency (ELQE) increases. At an optimal ELQE, the MC has a much narrower width than the MEL, indicating that the MC and MEL do not share a common origin. However, MC reverses and has the same width as MEL when exposed to a threshold laser power. We show that the e-h pair model can explain the positive MEL and MC while the negative MC can be explained by the bipolaron model

Single-crystal structure, photophysical characteristics and electroluminescent properties of bis(2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate)zinc

Energy Technology Data Exchange (ETDEWEB)

Xu Huixia, E-mail: xuhuixia0824@163.com [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Yue, Yan [Department of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China); Wang Hua [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Chen Liuqing [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Hao Yuying [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); Department of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China); Xu Bingshe [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Taiyuan 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China)

2012-04-15

In this paper, a zinc (II) complex of Zn{sub 2}(4-tfmBTZ){sub 4} (4-tfmBTZ=2-(4-trifluoromethyl-2-hydroxyphenyl)benzothiazolate) was reported. Via combination of experimental and theoretical approaches, its molecular structure, photophysical characteristics, electronic structure and electroluminescent properties were investigated. The results indicate that Zn{sub 2}(4-tfmBTZ){sub 4} exists as five-coordinate geometric structure and two zinc atoms are bridged by oxygen atoms. The intense absorption band was located at 404 nm, which mainly originate from the transition HOMO-1 to LUMO+2. The blue-light emission was observed in tetrahydrofuran solution and thin film. White-light emission with four emission peaks was observed with CIE coordinate of (0.29, 0.33) and a higher CRI of 85.1 by fabricating bilayer device using Zn{sub 2}(4-tfmBTZ){sub 4} as electron-transport and NPB as hole-transport material. - Highlights: Black-Right-Pointing-Pointer The single-crystal and electronic structures of Zn{sub 2}(4-tfmBTZ){sub 4}. Black-Right-Pointing-Pointer The multicolor emission of Zn{sub 2}(4-tfmBTZ){sub 4} were realized by the simple devices. Black-Right-Pointing-Pointer White OLED is achieved with particularly high color rending index (CRI) by the emission of Zn{sub 2}(4-tfmBTZ){sub 4}.

Electroluminescence from porous silicon due to electron injection from solution

NARCIS (Netherlands)

Kooij, Ernst S.; Despo, R.W.; Kelly, J.J.

1995-01-01

We report on the electroluminescence from p‐type porous silicon due to minority carrier injection from an electrolyte solution. The MV+• radical cation formed in the reduction of divalent methylviologen is able to inject electrons into the conduction band of crystalline and porous silicon. The

Low temperature transient response and electroluminescence characteristics of OLEDs based on Alq{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Yuan, Chao [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Guan, Min, E-mail: guanmin@semi.ac.cn [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zhang, Yang [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Yiyang; Liu, Shuangjie [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Zeng, Yiping [Key Laboratory of Semiconductor Material Sciences, Beijing Key Laboratory of Low Dimensional Semiconductor Materials and Devices, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); College of Materials Science and Optoelectronic Devices, University of Chinese Academy of Sciences, Beijing 100049 (China)

2017-08-15

Highlights: • The dependency relation between transmission rate and electron transport layer is revealed. • The critical temperature points for the influence of luminescent materials and injection barriers on delay time are found. • The influence of light-emitting material and injection layer on carrier accumulation is quantified. - Abstract: In this work, the organic light-emitting diodes (OLEDs) based on Alq{sub 3} are fabricated. In order to make clear the transport mechanism of carriers in organic light-emitting devices at low temperature, detailed electroluminescence transient response and the current-voltage–luminescence (I–V–L) characteristics under different temperatures in those OLEDs are investigated. It founds that the acceleration of brightness increases with increasing temperature is maximum when the temperature is 200 K and it is mainly affected by the electron transport layer (Alq{sub 3}). The MoO{sub 3} injection layer and the electroluminescent layer have great influence on the delay time when the temperature is 200 K. Once the temperature is greater than 250 K, the delay time is mainly affected by the MoO{sub 3} injection layer. On the contrary, the fall time is mainly affected by the electroluminescent material. The V{sub f} is the average growth rate of fall time when the temperature increases 1 K which represents the accumulation rate of carriers. The difference between V{sub f} caused by the MoO{sub 3} injection layer is 0.52 us/K and caused by the electroluminescent material Ir(ppy){sub 3} is 0.73 us/K.

High performance yellow organic electroluminescent devices by doping iridium(III) complex into host materials with stepwise energy levels

Energy Technology Data Exchange (ETDEWEB)

Cui, Rongzhen; Zhou, Liang, E-mail: zhoul@ciac.ac.cn; Jiang, Yunlong; Li, Yanan; Zhao, Xuesen; Zhang, Hongjie, E-mail: hongjie@ciac.ac.cn

2015-10-15

In this work, we aim to further improve the electroluminescent (EL) performances of a yellow light-emitting iridium(III) complex by designing double light-emitting layers (EMLs) devices having stepwise energy levels. Compared with single-EML devices, these designed double-EML devices showed improved EL efficiency and brightness attributed to better balance in carriers. In addition, the stepwise distribution in energy levels of host materials is instrumental in broadening the recombination zone, thus delaying the roll-off of EL efficiency. Based on the investigation of carriers' distribution, device structure was further optimized by adjusting the thickness of deposited layers. Finally, yellow EL device (Commission Internationale de l'Eclairage (CIE) coordinates of (0.446, 0.542)) with maximum current efficiency, power efficiency and brightness up to 78.62 cd/A (external quantum efficiency (EQE) of 21.1%), 82.28 lm/W and 72,713 cd/m{sup 2}, respectively, was obtained. Even at the high brightness of 1000 cd/m{sup 2}, EL efficiency as high as 65.54 cd/A (EQE=17.6%) can be retained. - Highlights: • Yellow electroluminescent devices were designed and fabricated. • P-type and n-type materials having stepwise energy levels were chosen as host materials. • Better balance of holes and electrons causes the enhanced efficiencies. • Improved carriers' trapping suppresses the emission of host material.

Study on electroluminescence processes in dye-doped organic light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Li Weizhi [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: leewz@uestc.edu.cn; Jiang Yadong; Wang Tao [State Key Laboratory of Electronic Thin Films and Integrated devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2008-07-15

Electroluminescence (EL) mechanism of dye-doped organic light-emitting diodes (OLEDs) was investigated by using three familiar fluorescent dyes, i.e., 5,12-Dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA), 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl) -4H-pyran(DCJTB), and 5,6,11,12-tetraphenylnaphthacene (Rubrene). EL spectra of the doped devices with structure of indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'- diamine (NPB) (40 nm)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3}) (x nm, x=0-40 nm)/dye: Alq{sub 3} (weight ratio{approx}1%, 2 nm)/Alq{sub 3} (48-x nm)/MgAg indicated that direct carrier trapping (DCT) process dominated light emission of devices. As a result, investigation of carrier-recombination site via doping, which is conventionally applied in OLEDs, is questionable since the doping site and the dopant itself may significantly influence the carrier-recombination process in the doped devices.

Interfacial exciplex electroluminescence between diamine derivatives with starburst molecular structure and tris(acetylacetonato)-(mono-phenothroline) thulium

International Nuclear Information System (INIS)

He Hong; Li Wenlian; Su Zisheng; Chu Bei; Bi Defeng; Chen Yiren; Wang Dan; Su Wenming; Li Bin

2009-01-01

The authors demonstrate the interfacial exciplex electroluminescence (EL) between tris(acetylacetonato)-(mono-phenothroline) thulium [Tm(AcA) 3 phen] and two diamine derivatives with starburst molecular structure- 4,4',4''-tris[2-naphthyl(phenyl)amino]triphenylamine (2-TNATA) and 4,4',4''-tris[3-methyl-pheny(phenyl)-amino]triphenyl-amine (m-MTDATA), both of which have the same ionization potential (IP) (approximately 5.1 eV). When the Tm-complex and the two diamine derivatives are respectively used as the electron accepter and donors, the two EL devices exhibit different exciplex emissions, which verifies our previously reported opinion regarding the effect of the different substitutes on exciplex emission [W.M. Su, W.L. Li, Q. Xin, Z.S. Su, B. Chu, D.F. Bi, H. He, J.H. Niu, Appl. Phys. Lett. 91 (2007) 043508]. When the mixture of the two diamine derivatives is used as a donor, a white EL device with the Commission International de l'Eclairage (CIE) coordinates of (0.277, 0.323) is achieved. The exciplex formation mechanisms of the devices with the two different donors are discussed

White Polymer Light-Emitting Diodes Based on Exciplex Electroluminescence from Polymer Blends and a Single Polymer.

Science.gov (United States)

Liang, Junfei; Zhao, Sen; Jiang, Xiao-Fang; Guo, Ting; Yip, Hin-Lap; Ying, Lei; Huang, Fei; Yang, Wei; Cao, Yong

2016-03-09

In this Article, we designed and synthesized a series of polyfluorene derivatives, which consist of the electron-rich 4,4'-(9-alkyl-carbazole-3,6-diyl)bis(N,N-diphenylaniline) (TPA-Cz) in the side chain and the electron-deficient dibenzothiophene-5,5-dioxide (SO) unit in the main chain. The resulting copolymer PF-T25 that did not comprise the SO unit exhibited blue light-emission with the Commission Internationale de L'Eclairage coordinates of (0.16, 0.10). However, by physically blending PF-T25 with a blue light-emitting SO-based oligomer, a novel low-energy emission correlated to exciplex emerged due to the appropriate energy level alignment of TPA-Cz and the SO-based oligomers, which showed extended exciton lifetime as confirmed by time-resolved photoluminescent spectroscopy. The low-energy emission was also identified in copolymers consisting of SO unit in the main chain, which can effectively compensate for the high-energy emission to produce binary white light-emission. Polymer light-emitting diodes based on the exciplex-type single greenish-white polymer exhibit the peak luminous efficiency of 2.34 cd A(-1) and the maximum brightness of 12 410 cd m(-2), with Commission Internationale de L'Eclairage color coordinates (0.27, 0.39). The device based on such polymer showed much better electroluminescent stability than those based on blending films. These observations indicated that developing a single polymer with the generated exciplex emission can be a novel and effective molecular design strategy toward highly stable and efficient white polymer light-emitting diodes.

Advanced Emissions Control Development Program: Mercury Control

International Nuclear Information System (INIS)

Evans, A.P.; Redinger, K.W.; Holmes, M.J.

1997-07-01

McDermott Technology, Inc. (a subsidiary of Babcock ampersand Wilcox) is conducting the Advanced Emissions Control Development Project (AECDP) which is aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPS) from coal-fired electric utility plants. The need for such controls may arise as the US Environmental Protection Agency (EPA) proceeds with implementation of requirements set forth in the Clean Air Act Amendments (CAAA's) of 1990. Promulgation of air toxics emissions regulations for electric utility plants could dramatically impact utilities burning coal, their industrial and residential customers, and the coal industry. AECDP project work will supply the information needed by utilities to respond to potential HAPs regulations in a timely, cost-effective, enviromnentally-sound manner which supports the continued use of the Nation's abundant reserves of coal, such as those in the State of Ohio. The development work is being carried out using the 10 MW Clean Environment Development Facility wherein air toxics emissions control strategies can be developed under controlled conditions. The specific objectives of the project are to (1) measure and understand production and partitioning of air toxics species for a variety of coals, (2) optimize the air toxics removal performance of conventional flue gas cleanup systems, (3) develop advanced air toxics emissions control concepts, (4) develop and validate air toxics emissions measurement and monitoring techniques, and (5) establish a comprehensive, self-consistent air toxics data library. This project is supported by the Department of Energy, the Ohio Coal Development Office within the Ohio Department of Development and Babcock ampersand Wilcox. A comprehensive assessment of HAP emissions from coal-fired electric utility boilers sponsored by the Department of Energy and the Electric Power Research Institute concluded that with the exception of

Influence of the polymer concentration on the electroluminescence of ZnO nanorod/polymer hybrid light emitting diodes

Science.gov (United States)

Zaman, Saima; Zainelabdin, Ahmed; Amin, Gul; Nur, Omer; Willander, Magnus

2012-09-01

The effects of the polymer concentration on the performance of hybrid light emitting diodes (LEDs) based on zinc oxide nanorods (ZnO NRs) and poly(9,9-dioctylfluorene) (PFO) were investigated. Various characterization techniques were applied to study the performance of the PFO/ZnO NR hybrid LEDs fabricated with various PFO concentrations. The fabricated hybrid LEDs demonstrated stable rectifying diode behavior, and it was observed that the turn-on voltage of the LEDs is concentration dependent. The measured room temperature electroluminescence (EL) showed that the PFO concentration plays a critical role in the emission spectra of the hybrid LEDs. At lower PFO concentrations of 2-6 mg/ml, the EL spectra are dominated by blue emission. However, by increasing the concentration to more than 8 mg/ml, the blue emission was completely suppressed while the green emission was dominant. This EL behavior was explained by a double trap system of excitons that were trapped in the β-phase and/or in the fluorenone defects in the PFO side. The effects of current injection on the hybrid LEDs and on the EL emission were also investigated. Under a high injection current, a new blue peak was observed in the EL spectrum, which was correlated to the creation of a new chemical species on the PFO chain. The green emission peak was also enhanced with increasing injection current because of the fluorenone defects. These results indicate that the emission spectra of the hybrid LEDs can be tuned by using different polymer concentrations and by varying the current injected into the device.

Electroluminescence analysis for spatial characterization of parasitic optical losses in silicon heterojunction solar cells

Science.gov (United States)

Ahmed, Nuha; Zhang, Lei; Sriramagiri, Gowri; Das, Ujjwal; Hegedus, Steven

2018-04-01

Electroluminescence (EL) coupled with reflection measurements are used to spatially quantify optical losses in silicon heterojunction solar cells due to plasmonic absorption in the metal back contacts. The effect of indium tin oxide back reflector in decreasing this plasmonic absorption is found to increase the reflection from the back nickel (Ni)-aluminum (Al) and Al metals by ˜12% and ˜41%, respectively, in both bifacial and front junction silicon solar cells. Losses due to back reflection are calculated by comparison between the EL emission signals in high and low back reflection samples and are shown to be in agreement with standard reflection measurements. We conclude that the optical properties of the back contact can significantly influence the EL intensity which complicates the interpretation of EL as being primarily due to recombination especially when comparing two different devices with spatially varying back surface structures.

Electroplex emission from bi-layer blue emitting organic materials

Science.gov (United States)

Zhang, Fujun; Zhao, Suling; Zhao, Dewei; Jiang, Weiwei; Li, Yuan; Yuan, Guangcai; Zhu, Haina; Xu, Zheng

2007-04-01

Electroluminescence (EL) and photoluminescence (PL) spectra of an electron donor, an (poly(N-vinylcarbazole) (PVK))/electron acceptor, and a (2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD)) bi-layer solid film are analysed. The EL emission peak has an apparent red-shift with the increase of driving voltage. There maybe exist an electroplex emission between the PVK and PBD interface under high electric field strength. According to their energy level, the electroplex emission peak should locate at 460 nm. There are great spectra overlapping between PVK emission and electroplex emission, and the ratio of electroplex emission intensity to exciton emission intensity (Ielectroplex/Iexciton) increases from 0.38 at 10 to 0.81 at 16 V. Therefore the measured emission peaks continuously shift from 410 nm at 10 V to 445 nm at 16 V.

Electroplex emission from bi-layer blue emitting organic materials

International Nuclear Information System (INIS)

Zhang Fujun; Zhao Suling; Zhao Dewei; Jiang Weiwei; Li Yuan; Yuan Guangcai; Zhu Haina; Xu Zheng

2007-01-01

Electroluminescence (EL) and photoluminescence (PL) spectra of an electron donor, an (poly(N-vinylcarbazole) (PVK))/electron acceptor, and a (2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD)) bi-layer solid film are analysed. The EL emission peak has an apparent red-shift with the increase of driving voltage. There maybe exist an electroplex emission between the PVK and PBD interface under high electric field strength. According to their energy level, the electroplex emission peak should locate at 460 nm. There are great spectra overlapping between PVK emission and electroplex emission, and the ratio of electroplex emission intensity to exciton emission intensity (I electroplex /I exciton ) increases from 0.38 at 10 to 0.81 at 16 V. Therefore the measured emission peaks continuously shift from 410 nm at 10 V to 445 nm at 16 V

Electroplex emission from bi-layer blue emitting organic materials

Energy Technology Data Exchange (ETDEWEB)

Zhang Fujun; Zhao Suling; Zhao Dewei; Jiang Weiwei; Li Yuan; Yuan Guangcai; Zhu Haina; Xu Zheng [Key Laboratory for Information Storage, Display and Materials, Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China)

2007-04-15

Electroluminescence (EL) and photoluminescence (PL) spectra of an electron donor, an (poly(N-vinylcarbazole) (PVK))/electron acceptor, and a (2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (PBD)) bi-layer solid film are analysed. The EL emission peak has an apparent red-shift with the increase of driving voltage. There maybe exist an electroplex emission between the PVK and PBD interface under high electric field strength. According to their energy level, the electroplex emission peak should locate at 460 nm. There are great spectra overlapping between PVK emission and electroplex emission, and the ratio of electroplex emission intensity to exciton emission intensity (I{sub electroplex}/I{sub exciton}) increases from 0.38 at 10 to 0.81 at 16 V. Therefore the measured emission peaks continuously shift from 410 nm at 10 V to 445 nm at 16 V.

Self-scaling minority carrier lifetime imaging using periodically modulated electroluminescence

Science.gov (United States)

Kropp, Timo; Berner, Marcel; Werner, Jürgen H.

2017-11-01

We present a straightforward self-scaling imaging technique to extract the effective minority carrier lifetime image of silicon solar cells using periodically modulated electroluminescence. This novel modulation technique overcomes main limiting factors linked to camera integration time. Our approach is based on comparing three luminescence images taken during current modulation. One image is taken while periodically injecting excess charge carriers with a pulsed current stimulation followed by an open-circuit luminescence decay. A second image with the same injection profile is taken while additionally extracting excess charge carriers at the falling edge, accelerating the luminescence decay. Both images are normalized to a steady-state image. The camera integration time is several orders of magnitude longer than the modulation period length, and no synchronization of image acquisition is needed. The intensity difference between both modulated images is used for determining a calibration factor to convert the steady-state image into the effective minority carrier lifetime image: Our modulation method enables carrier lifetime images completely independent of the image integration time. First carrier lifetime images show good agreement with data from time resolved electroluminescence.

Room-temperature near-infrared electroluminescence from boron-diffused silicon pn junction diodes

Directory of Open Access Journals (Sweden)

Si eLi

2015-02-01

Full Text Available Silicon pn junction diodes with different doping concentrations were prepared by boron diffusion into Czochralski (CZ n-type silicon substrate. Their room-temperature near-infrared electroluminescence (EL was measured. In the EL spectra of the heavily boron doped diode, a luminescence peak at ~1.6 m (0.78 eV was observed besides the band-to-band line (~1.1eV under the condition of high current injection, while in that of the lightly boron doped diode only the band-to-band line was observed. The intensity of peak at 0.78 eV increases exponentially with current injection with no observable saturation at room temperature. Furthermore, no dislocations were found in the cross-sectional transmission electron microscopy image, and no dislocation-related luminescence was observed in the low-temperature photoluminescence spectra. We deduce the 0.78 eV emission originates from the irradiative recombination in the strain region of diodes caused by the diffusion of large number of boron atoms into silicon crystal lattice.

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Science.gov (United States)

Gelloz, B.; Sano, H.; Boukherroub, R.; Wayner, D. D. M.; Lockwood, D. J.; Koshida, N.

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 °C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreatred devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device.

Enhanced electroluminescence of organic light-emitting diodes by using halloysite nanotubes

Energy Technology Data Exchange (ETDEWEB)

Mondragón, Margarita, E-mail: mmondragon@ipn.mx [Instituto Politécnico Nacional, ESIME Azcapotzalco, Av. de las Granjas 682, 02250 México D.F. (Mexico); Moggio, Ivana; León, Arxel de; Arias, Eduardo [Centro de Investigación en Química Aplicada, CIQA, Blvd. Enrique Reyna 140, 25253 Saltillo, Coahuila (Mexico)

2013-12-15

The effect of halloysite clay nanotubes (HNTs) on the optical and electronic properties of poly(2-methoxy-5-[2′-ethylhexyloxy]-1,4-phenylenevinylene) (MEH-PPV) have been investigated. The UV–vis absorption band of the conjugated polymer remains unchanged upon the incorporation of halloysite nanotubes (HNTs). Photoluminescence (PL) measurements reveal a decreased quantum yield in the MEH-PPV/HNTs nanocomposites, compared with bulk MEH-PPV. Improvement of the electroluminescence of organic light-emitting diodes (OLEDs) was achieved by incorporating high contents of HNTs. The nanotubes act to enhanced polymer aggregates, as revealed by AFM analysis, thus increasing charge transport and therefore electroluminescence but also decreasing PL quantum yield. -- Highlights: • Thin films of nanocomposites of MEH-PPV/HNTs were prepared by spin coating. • Quantum yield in the nanocomposites was decreased compared with bulk MEH-PPV. • Improvement of the EL of OLEDs was achieved by incorporating high contents of HNTs. • The HNTs act to enhanced polymer aggregates, as revealed by AFM.

Enhanced electroluminescence of organic light-emitting diodes by using halloysite nanotubes

International Nuclear Information System (INIS)

Mondragón, Margarita; Moggio, Ivana; León, Arxel de; Arias, Eduardo

2013-01-01

The effect of halloysite clay nanotubes (HNTs) on the optical and electronic properties of poly(2-methoxy-5-[2′-ethylhexyloxy]-1,4-phenylenevinylene) (MEH-PPV) have been investigated. The UV–vis absorption band of the conjugated polymer remains unchanged upon the incorporation of halloysite nanotubes (HNTs). Photoluminescence (PL) measurements reveal a decreased quantum yield in the MEH-PPV/HNTs nanocomposites, compared with bulk MEH-PPV. Improvement of the electroluminescence of organic light-emitting diodes (OLEDs) was achieved by incorporating high contents of HNTs. The nanotubes act to enhanced polymer aggregates, as revealed by AFM analysis, thus increasing charge transport and therefore electroluminescence but also decreasing PL quantum yield. -- Highlights: • Thin films of nanocomposites of MEH-PPV/HNTs were prepared by spin coating. • Quantum yield in the nanocomposites was decreased compared with bulk MEH-PPV. • Improvement of the EL of OLEDs was achieved by incorporating high contents of HNTs. • The HNTs act to enhanced polymer aggregates, as revealed by AFM

1.54 μm Er3+ electroluminescence from an erbium-compound-doped organic light emitting diode with a p-type silicon anode

International Nuclear Information System (INIS)

Zhao, W Q; Wang, P F; Ran, G Z; Ma, G L; Zhang, B R; Liu, W M; Wu, S K; Dai, L; Qin, G G

2006-01-01

By doping an erbium complex, erbium (III) 2, 4-pentanedionate (Er(acac) 3 ), into the ALQ layer, we fabricate a series of infrared emission organic light emitting diodes (OLED) with structures of p-Si/SiO 2 /NPB/ALQ/ ALQ:Er(acac) 3 /ALQ/Sm/Au, where p-Si is the anode and Sm/Au is the cathode. The 1.54 μm emission from Er 3+ is observed. The impact of doping level of Er(acac) 3 in ALQ on 1.54 μm electroluminescence (EL) intensity is studied, and the best mass ratio of Er(acac) 3 to ALQ is found at 1:60. A competitive EL mechanism from the ALQ and Er(acac) 3 is found and the Er 3+ ions excitations are attributed to energy transfer from the ligands to Er ions

Zn doped GaN for single-photon emission

Energy Technology Data Exchange (ETDEWEB)

Behrends, Arne; Ledig, Johannes; Al-Suleiman, Mohamed Aid Mansur; Bakin, Andrey; Waag, Andreas [Institute of Semiconductor Technology, University of Technology Braunschweig, Hans-Sommer-Str. 66, 38106 Braunschweig (Germany); Peters, Silke; Racu, Ana Maria; Schmunk, Waldemar; Hofer, Helmut; Kueck, Stefan [Physikalisch Technische Bundesanstalt (PTB), Bundesallee 100, 38116 Braunschweig (Germany)

2012-03-15

In this work we report on the optical investigation of Zn doped GaN films fabricated by metal organic chemical vapor deposition. The samples show bright emission in the blue spectral range around 2.9 eV when Si codoping is provided. This emission is suggested to be used for single-photon emission, thus the density of the Zn-Si pairs was drastically reduced leading to a decrease of the blue luminescence. For electrically excited single-photon sources these Zn-Si pairs have to be incorporated into LEDs, therefore we fabricated GaN-based nano-LEDs which show electroluminescence at 430 nm (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Plasmon mediated enhancement and tuning of optical emission properties of two dimensional graphitic carbon nitride nanosheets.

Science.gov (United States)

Bayan, Sayan; Gogurla, Narendar; Midya, Anupam; Singha, Achintya; Ray, Samit K

2017-12-01

We demonstrate surface plasmon induced enhancement and tunablilty in optical emission properties of two dimensional graphitic carbon nitride (g-C 3 N 4 ) nanosheets through the attachment of gold (Au) nanoparticles. Raman spectroscopy has revealed surface enhanced Raman scattering that arises due to the combined effect of the charge transfer process and localized surface plasmon induced enhancement in electromagnetic field, both occurring at the nanoparticle-nanosheet interface. Photoluminescence studies suggest that at an optimal concentration of nanoparticles, the emission intensity can be enhanced, which is maximum within the 500-525 nm region. Further, the fabricated electroluminescent devices reveal that the emission feature can be tuned from bluish-green to red (∼160 nm shift) upon attaching Au nanoparticles. We propose that the π*→π transition in g-C 3 N 4 can trigger surface plasmon oscillation in Au, which subsequently increases the excitation process in the nanosheets and results in enhanced emission in the green region of the photoluminescence spectrum. On the other hand, electroluminescence of g-C 3 N 4 can induce plasmon oscillation more efficiently and thus can lead to red emission from Au nanoparticles through the radiative damping of particle plasmons. The influence of nanoparticle size and coverage on the emission properties of two dimensional g-C 3 N 4 , nanosheets has also been studied in detail.

Synthesis, characterization, photophysics and electroluminescence based on a series of pyran-containing emitters

Energy Technology Data Exchange (ETDEWEB)

Yang Lifen [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Guan Min [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Bian Zuqiang [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China)]. E-mail: bianzq@pku.edu.cn; Xie Junqi [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Chen Tianpeng [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China); Huang Chunhui [State Key Laboratory of Rare Earth Materials Chemistry and Applications, Peking University, Beijing 100871 (China)]. E-mail: chhuang@pku.edu.cn

2006-04-03

Four unsymmetric as well as symmetric carbazole or oxadiazole modified pyran-containing compounds have been synthesized and characterized. These compounds are 4-(dicyanomethylene)-2-methyl-6-(4-(carbazolo-9-yl)phenyl)-4H-pyran (10), 4-(dicyanomethylene)-2,6-bis(4-(carbazolo-9-yl)phenyl)-4H-pyran (11), 4-(dicyanomethylene)-2-methyl-6-(4-tert-phenyl)-1,3,4-oxdiazole-4-phenyl)-4 H-pyran (12), and 4-(dicyanomethylene)-2,6-bis(4-tert-phenyl)-1,3, 4-oxdiazole-4-phenyl-4H-pyran (13). Photoluminescent measurements indicated that their maximal emissions can be tuned from 543 to 590 nm in acetone solution. Electroluminescent studies based on these compounds as dopants resulted in greenish yellow light emission. It was found that the device based on the bis-condensed symmetric compound (11) with the configuration of indium tin oxide / Copper (II) phthalocyanine (5 nm) / N,N'-bis-(1-naphthl)-diphenyl-1,1'-biphenyl-4,4'-diamine (40 nm) / compound (11) : tris-(8-quinolinolato)aluminium (Alq{sub 3}) (1%) (30 nm) / 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (5 nm) / Alq{sub 3} (40 nm) / Mg : Ag (9 : 1) (200 nm) / Ag (80 nm) has achieved the highest luminance (6869 cd/m{sup 2}) and efficiency (1.32 lm/W and 2.52 cd/A) among the four emitters.

Magnetic field enhanced electroluminescence in organic light emitting diodes based on electron donor-acceptor exciplex blends

Science.gov (United States)

Baniya, Sangita; Basel, Tek; Sun, Dali; McLaughlin, Ryan; Vardeny, Zeev Valy

2016-03-01

A useful process for light harvesting from injected electron-hole pairs in organic light emitting diodes (OLED) is the transfer from triplet excitons (T) to singlet excitons (S) via reverse intersystem crossing (RISC). This process adds a delayed electro-luminescence (EL) emission component that is known as thermally activated delayed fluorescence (TADF). We have studied electron donor (D)/acceptor(A) blends that form an exciplex manifold in which the energy difference, ΔEST between the lowest singlet (S1) and triplet (T1) levels is relatively small (exciplex blend is enhanced up to 40% by applying a relatively weak magnetic field of 50 mT at ambient. Moreover the MEL response is activated with activation energy similar that of the EL emission. This suggests that the large magneto-EL originates from an additional spin-mixing channel between singlet and triplet states of the generated exciplexes, which is due to TADF. We will report on the MEL dependencies on the temperature, bias voltage, and D-A materials for optimum OLED performance. Supported by SAMSUNG Global Research Outreach (GRO) program, and also by the NSF-Material Science & Engineering Center (MRSEC) program at the University of Utah (DMR-1121252).

Interfacial exciplex electroluminescence between diamine derivatives with starburst molecular structure and tris(acetylacetonato)-(mono-phenothroline) thulium

Energy Technology Data Exchange (ETDEWEB)

He Hong [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Li Wenlian [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)], E-mail: wllioel@yahoo.com.cn; Su Zisheng; Chu Bei; Bi Defeng; Chen Yiren; Wang Dan; Su Wenming; Li Bin [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China)

2009-02-20

The authors demonstrate the interfacial exciplex electroluminescence (EL) between tris(acetylacetonato)-(mono-phenothroline) thulium [Tm(AcA){sub 3}phen] and two diamine derivatives with starburst molecular structure- 4,4',4''-tris[2-naphthyl(phenyl)amino]triphenylamine (2-TNATA) and 4,4',4''-tris[3-methyl-pheny(phenyl)-amino]triphenyl-amine (m-MTDATA), both of which have the same ionization potential (IP) (approximately 5.1 eV). When the Tm-complex and the two diamine derivatives are respectively used as the electron accepter and donors, the two EL devices exhibit different exciplex emissions, which verifies our previously reported opinion regarding the effect of the different substitutes on exciplex emission [W.M. Su, W.L. Li, Q. Xin, Z.S. Su, B. Chu, D.F. Bi, H. He, J.H. Niu, Appl. Phys. Lett. 91 (2007) 043508]. When the mixture of the two diamine derivatives is used as a donor, a white EL device with the Commission International de l'Eclairage (CIE) coordinates of (0.277, 0.323) is achieved. The exciplex formation mechanisms of the devices with the two different donors are discussed.

Flexible electroluminescent device with inkjet-printed carbon nanotube electrodes

Science.gov (United States)

Azoubel, Suzanna; Shemesh, Shay; Magdassi, Shlomo

2012-08-01

Carbon nanotube (CNTs) inks may provide an effective route for producing flexible electronic devices by digital printing. In this paper we report on the formulation of highly concentrated aqueous CNT inks and demonstrate the fabrication of flexible electroluminescent (EL) devices by inkjet printing combined with wet coating. We also report, for the first time, on the formation of flexible EL devices in which all the electrodes are formed by inkjet printing of low-cost multi-walled carbon nanotubes (MWCNTs). Several flexible EL devices were fabricated by using different materials for the production of back and counter electrodes: ITO/MWCNT and MWCNT/MWCNT. Transparent electrodes were obtained either by coating a thin layer of the CNTs or by inkjet printing a grid which is composed of empty cells surrounded by MWCNTs. It was found that the conductivity and transparency of the electrodes are mainly controlled by the MWCNT film thickness, and that the dominant factor in the luminance intensity is the transparency of the electrode.

Room Temperature Electroluminescence from Tensile-Strained Si0.13Ge0.87/Ge Multiple Quantum Wells on a Ge Virtual Substrate

Directory of Open Access Journals (Sweden)

Guangyang Lin

2016-09-01

Full Text Available Direct band electroluminescence (EL from tensile-strained Si0.13Ge0.87/Ge multiple quantum wells (MQWs on a Ge virtual substrate (VS at room temperature is reported herein. Due to the competitive result of quantum confinement Stark effect and bandgap narrowing induced by tensile strain in Ge wells, electroluminescence from Γ1-HH1 transition in 12-nm Ge wells was observed at around 1550 nm. As injection current density increases, additional emission shoulders from Γ2-HH2 transition in Ge wells and Ge VS appeared at around 1300–1400 nm and 1600–1700 nm, respectively. The peak energy of EL shifted to the lower energy side superquadratically with an increase of injection current density as a result of the Joule heating effect. During the elevation of environmental temperature, EL intensity increased due to a reduction of energy between L and Γ valleys of Ge. Empirical fitting of the relationship between the integrated intensity of EL (L and injection current density (J with L~Jm shows that the m factor increased with injection current density, suggesting higher light emitting efficiency of the diode at larger injection current densities, which can be attributed to larger carrier occupations in the Γ valley and the heavy hole (HH valance band at higher temperatures.

Quantitative Prediction of Power Loss for Damaged Photovoltaic Modules Using Electroluminescence

Directory of Open Access Journals (Sweden)

Timo Kropp

2018-05-01

Full Text Available Electroluminescence (EL is a powerful tool for the qualitative mapping of the electronic properties of solar modules, where electronic and electrical defects are easily detected. However, a direct quantitative prediction of electrical module performance purely based on electroluminescence images has yet to be accomplished. Our novel approach, called “EL power prediction of modules” (ELMO as presented here, used just two electroluminescence images to predict the electrical loss of mechanically damaged modules when compared to their original (data sheet power. First, using this method, two EL images taken at different excitation currents were converted into locally resolved (relative series resistance images. From the known, total applied voltage to the module, we were then able to calculate absolute series resistance values and the real distribution of voltages and currents. Then, we reconstructed the complete current/voltage curve of the damaged module. We experimentally validated and confirmed the simulation model via the characterization of a commercially available photovoltaic module containing 60 multicrystalline silicon cells, which were mechanically damaged by hail. Deviation between the directly measured and predicted current/voltage curve was less than 4.3% at the maximum power point. For multiple modules of the same type, the level of error dropped below 1% by calibrating the simulation. We approximated the ideality factor from a module with a known current/voltage curve and then expand the application to modules of the same type. In addition to yielding series resistance mapping, our new ELMO method was also capable of yielding parallel resistance mapping. We analyzed the electrical properties of a commercially available module, containing 72 monocrystalline high-efficiency back contact solar cells, which suffered from potential induced degradation. For this module, we predicted electrical performance with an accuracy of better

Stable electroluminescence from passivated nano-crystalline porous silicon using undecylenic acid

Energy Technology Data Exchange (ETDEWEB)

Gelloz, B.; Sano, H.; Koshida, N. [Dept. Elec. and Elec. Eng., Tokyo Univ. of A and T, Koganei, Tokyo 184-8588 (Japan); Boukherroub, R. [Laboratoire de Physique de la Matiere Condensee, Ecole Polytechnique, Route de Saclay, 91128 Palaiseau (France); Wayner, D.D.M.; Lockwood, D.J. [National Research Council, Ottawa (Canada)

2005-06-01

Stabilization of electroluminescence from nanocrystalline porous silicon diodes has been achieved by replacing silicon-hydrogen bonds terminating the surface of nanocrystalline silicon with more stable silicon-carbon (Si-C) bonds. Hydrosilylation of the surface of partially and anodically oxidized porous silicon samples was thermally induced at about 90 C using various different organic molecules. Devices whose surface have been modified with stable covalent bonds shows no degradation in the EL efficiency and EL output intensity under DC operation for several hours. The enhanced stability can be attributed to the high chemical resistance of Si-C bonds against current-induced surface oxidation associated with the generation of nonradiative defects. Although devices treated with 1-decene exhibit reduced EL efficiency and brightness compared to untreated devices, other molecules, such as ethyl-undecylenate and particularly undecylenic acid provide stable and more efficient visible electroluminescence at room temperature. Undecylenic acid provides EL brightness as high as that of an untreated device. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Enhanced phosphorescence and electroluminescence in triplet emitters by doping gold into cadmium selenide/zinc sulfide nanoparticles

International Nuclear Information System (INIS)

Liu, H.-W.; Laskar, Inamur R.; Huang, C.-P.; Cheng, J.-A.; Cheng, S.-S.; Luo, L.-Y.; Wang, H.-R.; Chen, T.-M.

2005-01-01

Gold-cadmium selenide/zinc sulfide (Au-CdSe/ZnS) nanocomposites (NCs) were synthesized and characterized by transmission electron microscopy (TEM), energy dispersive X-ray (EDX) analysis, ultraviolet-visible (UV-visible) absorption and photoluminescence (PL) emission spectroscopy. The PL intensity in the Au-CdSe/ZnS NCs system was found to be much greater than that of CdSe/ZnS nanoparticles (NPs) alone, because of the surface-enhanced Raman scattering of Au NPs. Adding Au-CdSe/ZnS NCs to the cyclometalated iridium(III) complex (Ir-complex) greatly enhanced the PL intensity of a triplet emitter. Three double-layered electroluminescence (EL) devices were fabricated where the emitting zone contains the definite mixture of Ir-complex and the NCs [molar concentration of Ir-complex/NCs = 1:0 (Blank, D-1), 1:1 (D-2) and 1:3 (D-3)] and the device D-2 exhibited optimal EL performances

Electroluminescence properties of organic light-emitting diodes with a red dye doped into Alq{sub 3} : rubrene mixed host

Energy Technology Data Exchange (ETDEWEB)

Kang, H. Y. [Inha University, Incheon (Korea, Republic of); Lee, C. H. [Seoul National University, Seoul (Korea, Republic of)

2004-09-15

We have studied the electroluminescence (EL) properties of devices with a red fluorescent dye, 4-(dicyanomethylene)-2-t-butyl-6- (1,1,7,7-tetramethyl-julolidyl-9-enyl)--4H-py ran (DCJTB), doped into a mixed matrix of tris-(8-hydroxyquinoline)aluminum (Alq{sub 3}) and rubrene. The devices doped with DCJTB in the Alq{sub 3}:rubrene mixed host show an efficient red emission from DCJTB with negligible EL emission from both Alq{sub 3} and rubrene. The QE increases with increasing rubrene concentration and reaches a maximum of about 3.6 % for a DCJTB doping concentration of about 5 % in the Alq3:rubrene mixed (50:50 % ratio by weight) host, and then decreases at higher rubrene concentration, due to the concentration quenching effect. At a given bias voltage, the current density increases with increasing rubrene doping concentration, but it decreases with increasing DCJTB doping concentration. The results imply that the injected electrons and holes can transport via hopping through the energy levels of rubrene molecules while DCJTB acts as traps.

Large magneto-conductance and magneto-electroluminescence in exciplex-based organic light-emitting diodes at room temperature

Science.gov (United States)

Ling, Yongzhou; Lei, Yanlian; Zhang, Qiaoming; Chen, Lixiang; Song, Qunliang; Xiong, Zuhong

2015-11-01

In this work, we report on large magneto-conductance (MC) over 60% and magneto-electroluminescence (MEL) as high as 112% at room temperature in an exciplex-based organic light-emitting diode (OLED) with efficient reverse intersystem crossing (ISC). The large MC and MEL are individually confirmed by the current density-voltage characteristics and the electroluminescence spectra under various magnetic fields. We proposed that this type of magnetic field effect (MFE) is governed by the field-modulated reverse ISC between the singlet and triplet exciplex. The temperature-dependent MFEs reveal that the small activation energy of reverse ISC accounts for the large MFEs in the present exciplex-based OLEDs.

Color-tunable and stable-efficiency white organic light-emitting diode fabricated with fluorescent-phosphorescent emission layers

International Nuclear Information System (INIS)

Yang, Su-Hua; Shih, Po-Jen; Wu, Wen-Jie; Huang, Yi-Hua

2013-01-01

White organic light emitting diodes (OLEDs) were fabricated for color-tunable lighting applications. Fluorescent and phosphorescent hybrid emission layers (EMLs) were used to enhance the luminance and stability of the devices, which have blue-EML/CBP interlayer/green-EML/phosphorescent-sensitized-EML/red-EML structures. The influence of the composition and structure of the EMLs on the electroluminescence properties of the devices were investigated from the viewpoint of their emission spectra. The possible exciton harvesting, diffusion, transport, and annihilation processes occurring in the EMLs were also evaluated. A maximum luminance intensity of 7400 cd/m 2 and a highly stable current efficiency of 3.2 cd/A were obtained. Good color tunability was achieved for the white OLEDs; the chromatic coordinates linearly shifted from pure white (0.300, 0.398) to cold white (0.261, 0.367) when the applied voltage was varied from 10 to 14 V. -- Highlights: • Exciton harvesting, diffusion, transport, and annihilation processes were evaluated. • The electroluminescence properties were investigated from the viewpoint of the emission spectra. • Good color tunability and stable-efficiency were achieved for the white OLEDs

Electroluminescent drift chamber with 16 μm spatial resolution

International Nuclear Information System (INIS)

Baskakov, V.I.; Dolgoshein, V.A.; Lebedenko, V.N.

1978-01-01

Studied are the characteristics of the dft electroluminscent chamber of an original design. For insuring high spatial resolution, the chamber has been filled with xenon to a pressure of 20 atm, which substantially decreases the electron diffusion during drift. Located at the end of the drift gap is an anode wire, 50 μm in dia. A strong electric field available near the thin wire causes electroluminescence of the electrons. The signal is localized within a small volume and contribution of the luminescence time in the total duration of a signal is small. In this case no electron multiplication occurs at all and, consequently, no space charge of positive ions takes place, which makes it possible to operate at very high loadings (2x10 6 particle/s). The characteristics of the chamber are measured in a beam of the Serpukhov accelerator. Use has been made of a model comprising two chambers, 5 mm thick, located successively along the beam with the effective area being 40x40 mm. The studies and analysis performed reveal that the drift electroluminescent chamber operates reliably in the wide range of the working gas pressure at an intensity of the incident particles up to 10 5 particle/s. The best resolution is obtained at a pressure of 20 atm and it equals 16 μm

Controlling radiated emissions by design

CERN Document Server

Mardiguian, Michel

2014-01-01

The 3rd edition of Controlling Radiated Emissions by Design has been updated to reflect the latest changes in the field. New to this edition is material related to technical advances, specifically super-fast data rates on wire pairs, with no increase in RF interference. Throughout the book, details are given to control RF emissions using EMC design techniques. This book retains the step-by-step approach for incorporating EMC into every new design from the ground up. It describes the selection of quieter IC technologies, their implementation into a noise-free printed circuit layout, and the gathering of these into a low emissions package. Also included is how to design an I/O filter, along with connectors and cable considerations. All guidelines are supported throughout with comprehensive calculated examples. Design engineers, EMC specialists, and technicians will benefit from learning about the development of more efficient and economical control of emissions.

Two-phase xenon detector with gas amplification and electroluminescent signal detection

International Nuclear Information System (INIS)

Akimov, D.Yu.; Burenkov, A.A.; Grishkin, Yu.L.; Kovalenko, A.G.; Lebedenko, V.N.; Stekhanov, V.N.

2008-01-01

An optical technique for detecting ionization electrons produced during ionization of the liquid phase has been experimentally tested in two-phase (liquid-gas) xenon. The effects of gas and electroluminescent amplifications at the wire anode are simultaneously used for detection. This method allows construction of a supersensitive detector of small ionization signals-down to those corresponding to the detection of single electrons [ru

Coal fired flue gas mercury emission controls

International Nuclear Information System (INIS)

Wu, Jiang; Pan, Weiguo; Cao, Yan; Pan, Weiping

2015-01-01

Mercury (Hg) is one of the most toxic heavy metals, harmful to both the environment and human health. Hg is released into the atmosphere from natural and anthropogenic sources and its emission control has caused much concern. This book introduces readers to Hg pollution from natural and anthropogenic sources and systematically describes coal-fired flue gas mercury emission control in industry, especially from coal-fired power stations. Mercury emission control theory and experimental research are demonstrated, including how elemental mercury is oxidized into oxidized mercury and the effect of flue gas contents on the mercury speciation transformation process. Mercury emission control methods, such as existing APCDs (air pollution control devices) at power stations, sorbent injection, additives in coal combustion and photo-catalytic methods are introduced in detail. Lab-scale, pilot-scale and full-scale experimental studies of sorbent injection conducted by the authors are presented systematically, helping researchers and engineers to understand how this approach reduces the mercury emissions in flue gas and to apply the methods in mercury emission control at coal-fired power stations.

Coal fired flue gas mercury emission controls

Energy Technology Data Exchange (ETDEWEB)

Wu, Jiang; Pan, Weiguo [Shanghai Univ. of Electric Power (China); Cao, Yan; Pan, Weiping [Western Kentucky Univ., Bowling Green, KY (United States)

2015-05-01

Mercury (Hg) is one of the most toxic heavy metals, harmful to both the environment and human health. Hg is released into the atmosphere from natural and anthropogenic sources and its emission control has caused much concern. This book introduces readers to Hg pollution from natural and anthropogenic sources and systematically describes coal-fired flue gas mercury emission control in industry, especially from coal-fired power stations. Mercury emission control theory and experimental research are demonstrated, including how elemental mercury is oxidized into oxidized mercury and the effect of flue gas contents on the mercury speciation transformation process. Mercury emission control methods, such as existing APCDs (air pollution control devices) at power stations, sorbent injection, additives in coal combustion and photo-catalytic methods are introduced in detail. Lab-scale, pilot-scale and full-scale experimental studies of sorbent injection conducted by the authors are presented systematically, helping researchers and engineers to understand how this approach reduces the mercury emissions in flue gas and to apply the methods in mercury emission control at coal-fired power stations.

Narrow-band light emission from a single carbon nanotube p-n diode

Science.gov (United States)

Kinoshita, Megumi; Mueller, Thomas; Steiner, Mathias; Perebeinos, Vasili; Bol, Ageeth; Farmer, Damon; Avouris, Phaedon

2010-03-01

We present the first observation of electroluminescence from electrostatically-generated carbon nanotube (CNT) p-n junctions[1]. While CNT optoelectronics has made much progress in recent years, observations of emission from electrically excited CNT devices have been limited to the high-bias regime and with low efficiency. Furthermore, the resulting broad linewidths are broad, making it difficult to investigate electronic levels and carrier dynamics. We find that p-n junctions allow for better carrier control at lower power inputs, resulting in emission with near-zero threshold, low self-heating and efficiency two to three orders of magnitude greater compared to previous device configurations. This yields higher signal-to-noise ratio and narrower linewidths (down to ˜35 meV) that allows us to identify localized excitonic transitions that have previously been observed only in photoluminescent studies. [1] T. Mueller, M. Kinoshita, M. Steiner, V. Perebeinos, A. Bol, D. Farmer, and Ph. Avouris, Nature Nanotech., web publication, November 15 2009.

Terahertz emission from CdHgTe/HgTe quantum wells with an inverted band structure

Energy Technology Data Exchange (ETDEWEB)

Vasilyev, Yu. B., E-mail: Yu.Vasilyev@mail.ioffe.ru [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation); Mikhailov, N. N. [Russian Academy of Sciences, Rzhanov Institute of Semiconductor Physics, Siberian Branch (Russian Federation); Vasilyeva, G. Yu.; Ivánov, Yu. L.; Zakhar’in, A. O.; Andrianov, A. V. [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation); Vorobiev, L. E.; Firsov, D. A. [Peter the Great Saint-Petersburg Polytechnic University (Russian Federation); Grigoriev, M. N. [Ustinov Baltic State Technical University “VOENMEKh” (Russian Federation); Antonov, A. V.; Ikonnikov, A. V.; Gavrilenko, V. I. [Russian Academy of Sciences, Institute for Physics of Microstructures (Russian Federation)

2016-07-15

The terahertz electroluminescence from Cd{sub 0.7}Hg{sub 0.3}Te/HgTe quantum wells with an inverted band structure in lateral electric fields is experimentally detected and studied. The emission-spectrum maximum for wells 6.5 and 7 nm wide is near 6 meV which corresponds to interband optical transitions. The emission is explained by state depletion in the valence band and conduction band filling due to Zener tunneling, which is confirmed by power-law current–voltage characteristics.

Efficient blue-green and green electroluminescent devices obtained by doping iridium complexes into hole-block material as supplementary light-emitting layer

Energy Technology Data Exchange (ETDEWEB)

Zhou, Liang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zheng, Youxuan, E-mail: yxzheng@mail.nju.edu.cn [State Key Laboratory of Coordination Chemistry, Nanjing National Laboratory of Microstructures, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China); Deng, Ruiping; Feng, Jing; Song, Mingxing; Hao, Zhaomin [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zhang, Hongjie, E-mail: hongjie@ciac.jl.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zuo, Jinglin; You, Xiaozeng [State Key Laboratory of Coordination Chemistry, Nanjing National Laboratory of Microstructures, School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210093 (China)

2014-04-15

In this work, organic electroluminescent (EL) devices with dominant and supplementary light-emitting layers (EMLs) were designed to further improve the EL performances of two iridium{sup III}-based phosphorescent complexes, which have been reported to provide EL devices with slow EL efficiency roll-off. The widely used hole-block material 2,2′,2''-(1,3,5-Benzinetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) was selected as host material to construct the supplementary EML. Compared with single-EML devices, double-EMLs devices showed higher EL efficiencies, higher brightness, and lower operation voltage attributed to wider recombination zone and better balance of carriers. In addition, the insertion of supplementary EML is instrumental in facilitating carriers trapping, thus improving the color purity. Finally, high performance blue-green and green EL devices with maximum current efficiencies of 35.22 and 90.68 cd/A, maximum power efficiencies of 26.36 and 98.18 lm/W, and maximum brightness of 56,678 and 112,352 cd/m{sup 2}, respectively, were obtained by optimizing the doping concentrations. Such a device design strategy extends the application of a double EML device structure and provides a chance to simplify device fabrication processes. -- Highlights: • Electroluminescent devices with supplementary light-emitting layer were fabricated. • Doping concentrations and thicknesses were optimized. • Better balance of holes and electrons causes the enhanced efficiency. • Improved carrier trapping suppresses the emission of host material.

Radiation emitter-detector package

International Nuclear Information System (INIS)

O'Brien, J.T.; Limm, A.C.; Nyul, P.; Tassia, V.S. Jr.

1978-01-01

Mounted on the metallic base of a radiation emitter-detector is a mounting block is a first projection, and a second projection. A radiation detector is on the first projection and a semiconductor electroluminescent device, i.e., a radiation emitter, is on the second projection such that the plane of the recombination region of the electroluminescent device is perpendicular to the radiation incident surface of the radiation detector. The electroluminescent device has a primary emission and a secondary emission in a direction different from the primary emission. A radiation emitter-detector package as described is ideally suited to those applications wherein the secondary radiation of the electroluminescent device is fed into a feedback circuit regulating the biasing current of the electroluminescent device

Comparison of the electroluminescence of a red fluorescent dye doped into the Alq{sub 3} and Alq{sub 3}:rubrene mixed host

Energy Technology Data Exchange (ETDEWEB)

Kang, Hee-Young; Kang, Gi-Wook; Park, Kyung-Min; Yoo, In-Sun; Lee, Changhee

2004-01-05

We studied the effect of a mixed host of Alq{sub 3} and rubrene on the energy transfer and charge trapping processes in organic light-emitting devices with a red fluorescent dopant of 4-(dicyanomethylene)-2-tert-butyl-6 (1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB). The temperature dependence of electroluminescence (EL) properties is compared for the device with DCJTB doped into the Alq{sub 3} only host and that with the Alq{sub 3}:rubrene mixed host. The device with the Alq{sub 3}:rubrene mixed host shows an efficient red emission from DCJTB, negligible EL emission from Alq{sub 3}, and a lower EL drive voltage compared to the device with the Alq{sub 3} only host. Upon cooling the device temperature, the EL emission from rubrene increases but the emission from Alq{sub 3} is still weak, and the quantum efficiency (QE) is almost temperature-independent for the device with the Alq{sub 3}:rubrene mixed host. On the contrary, the EL emission from Alq{sub 3} increases and the QE decreases for devices with the Alq{sub 3} only host at low temperature. The results indicate that recombination of injected electrons and holes occurs on rubrene and subsequent energy transfer to DCJTB dominates in the device with the Alq{sub 3}:rubrene mixed host.

Electroluminescence property improvement by adjusting quantum wells’ position relative to p-doped region in InGaN/GaN multiple-quantum-well light emitting diodes

Directory of Open Access Journals (Sweden)

P. Chen

2017-03-01

Full Text Available The hole distribution and electroluminescence property improvement by adjusting the relative position between quantum wells and p-doped region in InGaN/GaN multiple-quantum-well structures are experimentally and theoretically investigated. Five designed samples with different barrier layer parameters of multiple-quantum-well structure are grown by MOCVD and then fabricated into devices. The electroluminescence properties of these samples are measured and compared. It is found that the output electroluminescence intensity of samples is enhanced if the position of quantum wells shifts towards p-side, while the output power is reduced if their position is shifted towards the n-side. The theoretical calculation of characteristics of these devices using the simulation program APSYS agrees well with the experimental data, illustrating that the effect of relative position between p-doped region and quantum wells on the improvement of hole distribution and electroluminescence performance is significant, especially for InGaN/GaN multiple-quantum-well devices operated under high injection condition.

Aggregation-Induced Emission Enhancement from Disilane-Bridged Donor-Acceptor-Donor Luminogens Based on the Triarylamine Functionality.

Science.gov (United States)

Usuki, Tsukasa; Shimada, Masaki; Yamanoi, Yoshinori; Ohto, Tatsuhiko; Tada, Hirokazu; Kasai, Hidetaka; Nishibori, Eiji; Nishihara, Hiroshi

2018-04-18

Six novel donor-acceptor-donor organic dyes containing a Si-Si moiety based on triarylamine functionalities as donor units were prepared by Pd-catalyzed arylation of hydrosilanes. Their photophysical, electrochemical, and structural properties were studied in detail. Most of the compounds showed attractive photoluminescence (PL) and electrochemical properties both in solution and in the solid state because of intramolecular charge transfer (ICT), suggesting these compounds could be useful for electroluminescence (EL) applications. The aggregation-induced emission enhancement (AIEE) characteristics of 1 and 3 were examined in mixed water/THF solutions. The fluorescence intensity in THF/water was stronger in the solution with the highest ratio of water because of the suppression of molecular vibration and rotation in the aggregated state. Single-crystal X-ray diffraction of 4 showed that the reduction of intermolecular π-π interaction led to intense emission in the solid state and restricted intramolecular rotation of the donor and acceptor moieties, thereby indicating that the intense emission in the solid state is due to AIEE. An electroluminescence device employing 1 as an emitter exhibited an external quantum efficiency of up to 0.65% with green light emission. The emission comes solely from 1 because the EL spectrum is identical to that of the PL of 1. The observed luminescence was sufficiently bright for application in practical devices. Theoretical calculations and electrochemical measurements were carried out to aid in understanding the optical and electrochemical properties of these molecules.

Progress and Prospects in Stretchable Electroluminescent Devices

Directory of Open Access Journals (Sweden)

Wang Jiangxin

2017-03-01

Full Text Available Stretchable electroluminescent (EL devices are a new form of mechanically deformable electronics that are gaining increasing interests and believed to be one of the essential technologies for next generation lighting and display applications. Apart from the simple bending capability in flexible EL devices, the stretchable EL devices are required to withstand larger mechanical deformations and accommodate stretching strain beyond 10%. The excellent mechanical conformability in these devices enables their applications in rigorous mechanical conditions such as flexing, twisting, stretching, and folding.The stretchable EL devices can be conformably wrapped onto arbitrary curvilinear surface and respond seamlessly to the external or internal forces, leading to unprecedented applications that cannot be addressed with conventional technologies. For example, they are in demand for wide applications in biomedical-related devices or sensors and soft interactive display systems, including activating devices for photosensitive drug, imaging apparatus for internal tissues, electronic skins, interactive input and output devices, robotics, and volumetric displays. With increasingly stringent demand on the mechanical requirements, the fabrication of stretchable EL device is encountering many challenges that are difficult to resolve. In this review, recent progresses in the stretchable EL devices are covered with a focus on the approaches that are adopted to tackle materials and process challenges in stretchable EL devices and delineate the strategies in stretchable electronics. We first introduce the emission mechanisms that have been successfully demonstrated on stretchable EL devices. Limitations and advantages of the different mechanisms for stretchable EL devices are also discussed. Representative reports are reviewed based on different structural and material strategies. Unprecedented applications that have been enabled by the stretchable EL devices are

Mixing of phosphorescent and exciplex emission in efficient organic electroluminescent devices.

Science.gov (United States)

Cherpak, Vladyslav; Stakhira, Pavlo; Minaev, Boris; Baryshnikov, Gleb; Stromylo, Evgeniy; Helzhynskyy, Igor; Chapran, Marian; Volyniuk, Dmytro; Hotra, Zenon; Dabuliene, Asta; Tomkeviciene, Ausra; Voznyak, Lesya; Grazulevicius, Juozas Vidas

2015-01-21

We fabricated a yellow organic light-emitting diode (OLED) based on the star-shaped donor compound tri(9-hexylcarbazol-3-yl)amine, which provides formation of the interface exciplexes with the iridium(III) bis[4,6-difluorophenyl]-pyridinato-N,C2']picolinate (FIrpic). The exciplex emission is characterized by a broad band and provides a condition to realize the highly effective white OLED. It consists of a combination of the blue phosphorescent emission from the FIrpic complex and a broad efficient delayed fluorescence induced by thermal activation with additional direct phosphorescence from the triplet exciplex formed at the interface. The fabricated exciplex-type device exhibits a high brightness of 38 000 cd/m(2) and a high external quantum efficiency.

Electroluminescence and electrical degradation of insulating polymers at electrode interfaces under divergent fields

Science.gov (United States)

Zhang, Shuai; Li, Qi; Hu, Jun; Zhang, Bo; He, Jinliang

2018-04-01

Electrical degradation of insulating polymers at electrode interfaces is an essential factor in determining long-term reliability. A critical challenge is that the exact mechanism of degradation is not fully understood, either experimentally or theoretically, due to the inherent complex processes. Consequently, in this study, we investigate electroluminescence (EL) at the interface of an electrode and insulator, and determine the relationship between EL and electrical degradation. Using a tip-plate electrode structure, the unique features of EL under a highly divergent field are investigated. The voltage type (alternating or direct current), the polymer matrix, and the time of pressing are also investigated separately. A study of EL from insulators under a divergent field is provided, and the relationship between EL spectra and degradation is discussed. It is shown that EL spectra under a divergent field have unique characteristics compared with EL spectra from polymer films under a uniform field and the most obvious one is the UV emission. The results obtained in the current investigation bring us a step closer to understanding the process of electrical degradation and provide a potential way to diagnose insulator defects.

Synthesis, structures, and electroluminescent properties of scandium N,O-chelated complexes toward near-white organic light-emitting diodes.

Science.gov (United States)

Katkova, Marina A; Balashova, Tatyana V; Ilichev, Vasilii A; Konev, Alexey N; Isachenkov, Nikolai A; Fukin, Georgy K; Ketkov, Sergey Yu; Bochkarev, Mikhail N

2010-06-07

Three members of a new class of electroluminescent, neutral, and monomeric scandium N,O-chelate complexes, namely, Sc(III)-tris-2-(2-benzoimidazol-2-yl)phenolate (1), Sc(III)-tris-2-(2-benzoxyazol-2-yl)phenolate (2), and Sc(III)-tris-2-(2-benzothiazol-2-yl)phenolate (3), have been prepared and X-ray characterized. DFT calculations have been performed. In contrast to the most frequently applied dual or multiple dopants in multilayer white OLED devices, all our simpler devices with the configuration of indium tin oxide/N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine/neat scandium complex/Yb exhibit close to near-white emission with a blue hue (CIE(x,y) = 0.2147, 0.2379) in the case of 1, a cyan hue (0.2702, 0.3524) in the case of 2, and a yellowish hue (0.3468; 0.4284) in the case of 3.

Exciplex or electroplex emissions from the interface between aromatic diamine and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline?

Science.gov (United States)

Zhu, Haina; Xu, Zheng; Zhang, Fujun; Zhao, Suling; Song, Dandan

2008-06-01

Organic light-emitting diodes (OLEDs) have been fabricated which consist of N, N'-diphenyl- N, N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine) (TPD), 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP), and tris(8-hydroxyquinoline) aluminum (Alq 3). Four emission peaks located at about 401 nm, 425 nm, 452 nm and 480 nm have been obtained in the electroluminescence (EL) spectra of these devices. The former two emissions originate from the exciton emission of TPD molecular. The last two emissions could be attributed to local (LOC) exiplex emission and charge transfer (CT) exiplex emission at the interface between TPD and BCP layers, respectively.

Sharp green electroluminescence from 1H-pyrazolo[3,4-b]quinoline-based light-emitting diodes

Science.gov (United States)

Tao, Y. T.; Balasubramaniam, E.; Danel, A.; Jarosz, B.; Tomasik, P.

2000-09-01

A multilayer organic light-emitting diode was fabricated using a fluorescent compound {6-N,N-diethylamino-1-methyl-3-phenyl-1H-pyrazolo[3,4-b]quinoline} (PAQ-NEt2) doped into the hole-transporting layer of NPB {4,4'-bis[N-(1-naphthyl-1-)-N-phenyl-amino]-biphenyl}, with the TPBI {2,2',2″-(1,3,5-phenylene)tris[1-phenyl-1H-benzimidazole]} as an electrontransporting material. At 16% PAQ-NEt2 doping concentration, the device gave a sharp, bright, and efficient green electroluminescence (EL) peaked at around 530 nm. The full width at half maximum of the EL is 60 nm, which is 60% of the green emission from typical NPB/AlQ [where AlQ=tris(8-hydroxyquinoline) aluminum] device. For the same concentration, a maximum luminance of 37 000 cd/m2 was obtained at 10.0 V and the maximum power, luminescence, and external quantum efficiencies were obtained 4.2 lm/W, 6.0 cd/A, and 1.6%, respectively, at 5.0 V.

Advanced Emissions Control Development Program

Energy Technology Data Exchange (ETDEWEB)

A.P.Evans; K.E. Redinger; M.J. Holmes

1998-04-01

The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

Biomass fueled fluidized bed combustion: atmospheric emissions, emission control devices and environmental regulations

International Nuclear Information System (INIS)

Grass, S.W.; Jenkins, B.M.

1994-01-01

Fluidized bed combustors have become the technological choice for power generation from biomass fuels in California. Atmospheric emission data obtained during compliance tests are compared for five operating 18 to 32 MW fluidized bed combustion power plants. The discussion focuses on the impact of fuel properties and boiler design criteria on the emission of pollutants, the efficiency of pollution control devices, and regulations affecting atmospheric emissions. Stack NO x emission factors are shown not to vary substantially among the five plants which burn fuels with nitrogen concentrations between 0.3 and 1.1% dry weight. All facilities use at least one particular control device, but not all use limestone injection or other control techniques for sulfur and chlorine. The lack of control for chlorine suggests the potential for emission of toxic species due to favorable temperature conditions existing in the particulate control devices, particularly when burning fuels containing high concentrations of chlorine. (Author)

Synthesis and Electroluminescent Properties of Bis(3H-1,2,3-triazolo-[4,5-b]pyridine-3-olzinc Zn(TAP2

Directory of Open Access Journals (Sweden)

Trinh Dac Hoanh

2012-01-01

Full Text Available A new light-emissive material, bis(3H-1,2,3-triazolo-[4,5-b]pyridine-3-olzinc (Zn(TAP2, has been synthesized and characterized by FT-NMR, FT-IR, UV-Vis, and elemental analysis. The photoluminescence (PL of Zn(TAP2 was measured from the DMF solution at 460 nm. The HOMO (6.5 eV and LUMO (2.8 eV energy levels of Zn(TAP2 were estimated from the measurement of cyclic voltammetry. The devices with structures of ITO/NPB/Zn(TAP2/LiF/Al and ITO/NPB/Zn(TAP2/Alq3/LiF/Al were constructed to investigate their electroluminescent (EL performance. Zn (TAP2 is supposed to be a good emitting material in the EL device.

Characterization of UV-enhanced SiPMs for Imaging in High Pressure Xenon Electroluminescent TPC

International Nuclear Information System (INIS)

Yahlali, Nadia; Lorca, David; Fernandes, L.M.P.

2013-06-01

The possibility of recording charged particle tracks in an electro-luminescent xenon gas TPC is investigated using a SiPM-based tracking system, operated in the demonstrator prototype of the NEXT-100 ββ decay experiment. The tracks of the ββ0ν events from the decay of the 136 Xe isotope have a distinctive topology, which allows their discrimination against single-electron events from the natural radioactivity that populates the region of interest of the neutrinoless decay in the ββ energy spectrum. Combined to the near-intrinsic energy resolution of the gaseous detector, this tracking capability provides a powerful background rejection tool for the search of the neutrinoless ββ decay aimed by the experiment. The NEXT-100 detector concepts and sensitivity and the first results of its demonstrator prototype are presented. The characterization studies relevant for the operation of UV-enhanced SiPMs used for imaging in an electro-luminescent TPC are reviewed. (authors)

Structural, morphological and electroluminescence studies of Zno:Co nanophosphor

Science.gov (United States)

Singh, Anju; Vishwakarma, H. L.

2016-09-01

The nanoparticles of zinc oxide (ZnO) doped with various concentrations of cobalt (Co) were synthesized by chemical precipitation method in the presence of capping agent polyvinylpyrrolidone (PVP). The effect of doping concentration on structural and morphological properties has been studied by X-ray diffraction (XRD) and scanning electron microscope (SEM). Cell volume, bond length, texture coefficient, lattice constants and dislocation density are also studied. Here, we also compared the interplaner spacing and relative peak intensities from their standard values with different angles. Crystallite sizes have been calculated by Debye-Scherrer's formula whose values are decreasing with increase in cobalt content up to 3 %. It has been seen that the growth orientation of the prepared ZnO nanorods was (101). The XRD analysis also ensures that ZnO has a hexagonal (wurtzite) crystal structure. The electroluminescence (EL) cells were prepared by placing pure and cobalt-doped ZnO nanoparticles between ITO-coated conducting glass plate and aluminium foil. Alternating voltage of various frequencies was applied, and EL brightness at different voltages was measured and corresponding current was also recorded. The voltage dependence of electroluminescence (EL) brightness of the ZnO:Co shows exponential increase. The linear voltage-current characteristic indicates ohmic nature. The EL brightness at a particular voltage is found to increase by increasing Co doping, but for higher percentage of Co the EL brightness is reduced. It is also seen that Co does not influence the threshold voltage. The brightness is also affected by increasing the frequency of AC signal.

Control of a White Organic Light Emitting Diode emission parameters using a single doped RGB active layer

Energy Technology Data Exchange (ETDEWEB)

Pereira, D. [Departamento de Ciência dos Materiais e i3N – Instituto de Nanoestruturas, Nanomodelação e Nanofabricação, Faculdade de Ciências e Tecnologia, Universidade Nova de Lisboa, Campus da Caparica, 2829-516 Caparica (Portugal); Pinto, A.; Califórnia, A.; Gomes, J. [CeNTI – Centro de Nanotecnologia, Materiais Técnicos, Funcionais e Inteligentes, Rua Fernando Mesquita 2785, 4760-034 Vila Nova de Famalicão (Portugal); Pereira, L., E-mail: luiz@ua.pt [Departmento de Física e i3N – Instituto de Nanoestruturas, Nanomodelação e Nanofabricação, Universidade de Aveiro, 3810-193 Aveiro (Portugal)

2016-09-15

Highlights: • A simple WOLED for Solid State Lighting is proposed with high color stability. • Energy transfer and electroluminescence dynamics of a single RGB layer for WOLEDs. • White shade modulation and stability over large emitting areas and applied voltages. - Abstract: Solid State Lighting technologies based on Organic Light Emitting Diodes, became an interesting focus due to their unique properties. The use of a unique RGB active layer for white emission, although simple in theory, shows difficulty to stabilize both CIE coordinates and color modulation. In this work, a WOLED using a simple RGB layer, was developed achieving a high color stability and shade modulation. The RGB matrix comprises a blue host material NPB, doped with two guests, a green (Coumarin 153) and a red (DCM1) in low concentrations. The RGB layer carrier dynamics allows for the white emission in low device complexity and high stability. This was also shown independent of the white shade, obtained through small changes in the red dopant resulting in devices ranging from warm to cool white i.e. an easy color tuning. A detailed analysis of the opto-electrical behavior is made.

Control of a White Organic Light Emitting Diode emission parameters using a single doped RGB active layer

International Nuclear Information System (INIS)

Pereira, D.; Pinto, A.; Califórnia, A.; Gomes, J.; Pereira, L.

2016-01-01

Highlights: • A simple WOLED for Solid State Lighting is proposed with high color stability. • Energy transfer and electroluminescence dynamics of a single RGB layer for WOLEDs. • White shade modulation and stability over large emitting areas and applied voltages. - Abstract: Solid State Lighting technologies based on Organic Light Emitting Diodes, became an interesting focus due to their unique properties. The use of a unique RGB active layer for white emission, although simple in theory, shows difficulty to stabilize both CIE coordinates and color modulation. In this work, a WOLED using a simple RGB layer, was developed achieving a high color stability and shade modulation. The RGB matrix comprises a blue host material NPB, doped with two guests, a green (Coumarin 153) and a red (DCM1) in low concentrations. The RGB layer carrier dynamics allows for the white emission in low device complexity and high stability. This was also shown independent of the white shade, obtained through small changes in the red dopant resulting in devices ranging from warm to cool white i.e. an easy color tuning. A detailed analysis of the opto-electrical behavior is made.

Bifunctional electroluminescent and photovoltaic devices using bathocuproine as electron-transporting material and an electron acceptor

International Nuclear Information System (INIS)

Chen, L.L.; Li, W.L.; Li, M.T.; Chu, B.

2007-01-01

Electroluminescence (EL) devices, using 4, 4',4''-tris (2-methylphenyl- phenylamino) triphenylamine (m-MTDATA) as hole-transporting material and bathocuproine (BCP) as an electron-transporting material, were fabricated, which emitted bright green light peaked at 520 nm instead of the emission of m-MTDATA or BCP. It was attributed to the exciplex formation and emission at the interface of m-MTDATA and BCP. EL performance was significantly enhanced by a thin mixed layer (5 nm) of m-MTDATA and BCP inserted between the two organic layers of the original m-MTDATA/BCP bilayer device. The trilayer device showed maximum luminance of 1,205 cd/m 2 at 8 V. At a luminance of 100 cd/m 2 , the power efficiency is 1.64 cd/A. Commission International De L'Eclairoge (CIE) color coordinates of the output spectrum of the devices at 8 V are x=0.244 and y=0.464. These devices also showed photovoltaic (PV) properties, which were sensitive to UV light. The PV diode exhibits high open-circuit voltage (V oc ) of 2.10 V under illumination of 365 nm UV light with 2 mW/cm 2 . And the short-circuit current (I sc ) of 92.5x10 -6 A/cm 2 , fill factor (FF) of 0.30 and power conversion efficiency (η e ) of 2.91% are respectively achieved. It is considered that strong exciplex emission in an EL device is a good indicator of efficient charge transfer at the organic interface, which is a basic requirement for good PV performance. Both the bilayer and trilayer devices showed EL and PV properties, suggesting their potential use as multifunction devices

Moisture exposure to different layers in organic light-emitting diodes and the effect on electroluminescence characteristics

International Nuclear Information System (INIS)

Liao, L. S.; Tang, C. W.

2008-01-01

Moisture effect on electroluminescence characteristics, including current density versus voltage, luminance versus voltage, luminous efficiency versus current density, dark spot formation, and operational stability of organic light-emitting diodes, has been systematically investigated by exposing each layer of the devices to moisture at room temperature. Moisture has a different effect on each of the interfaces or surfaces, and the influence increases as exposure time increases. There is a slight effect on the electroluminescence characteristics after the anode surface has been exposed to moisture. However, severe luminance decrease, dark spot formation, and operational stability degradation take place after the light-emitting layer or the electron-transporting layer is exposed to moisture. It is also demonstrated that the effect of moisture can be substantially reduced if the exposure to moisture is in a dark environment

Tunable light emission by exciplex state formation between hybrid halide perovskite and core/shell quantum dots: Implications in advanced LEDs and photovoltaics.

Science.gov (United States)

Sanchez, Rafael S; de la Fuente, Mauricio Solis; Suarez, Isaac; Muñoz-Matutano, Guillermo; Martinez-Pastor, Juan P; Mora-Sero, Ivan

2016-01-01

We report the first observation of exciplex state electroluminescence due to carrier injection between the hybrid lead halide perovskite (MAPbI3-xClx) and quantum dots (core/shell PbS/CdS). Single layers of perovskite (PS) and quantum dots (QDs) have been produced by solution processing methods, and their photoluminescent properties are compared to those of bilayer samples in both PS/QD and QD/PS configurations. Exciplex emission at lower energies than the band gap of both PS and QD has been detected. The exciplex emission wavelength of this mixed system can be simply tuned by controlling the QD size. Light-emitting diodes (LEDs) have been fabricated using those configurations, which provide light emission with considerably low turn-on potential. The "color" of the LED can also be tuned by controlling the applied bias. The presence of the exciplex state PS and QDs opens up a broad range of possibilities with important implications not only in tunable LEDs but also in the preparation of intermediate band gap photovoltaic devices with the potentiality of surpassing the Shockley-Queisser limit.

Electroluminescence in quantum well heterostructures p-Al{sub x}Ga{sub 1-x}As/GaAs{sub 1-y}P{sub y}/n-Al{sub x}Ga{sub 1-x}As under uniaxial stress

Energy Technology Data Exchange (ETDEWEB)

Berman, Irina V. [Physics Department, San Jose State University, CA (United States); Bogdanov, Evgeniy V.; Minina, Natalia Ya.; Shirokov, Stanislav S.; Yunovich, Alexander E. [Physics Department, Lomonosov Moscow State University (Russian Federation); Kissel, Heiko [R and D Department, DILAS Diodenlaser GmbH, (Germany)

2009-03-15

We present new results on the influence of uniaxial stress up to P=4 kbar on the electroluminescence spectra and current-voltage characteristics of p-Al{sub x}Ga{sub 1-x}As/GaAs{sub 1-y}P{sub y}/n-Al{sub x}Ga{sub 1-x}As double heterostructures usually used in TM emitting 808 nm high-power diode lasers. With increasing stress, the emission spectra demonstrate a blue shift of up to 25 meV at a pressure of P=4 kbar, while the electroluminescence intensity increases under compression. The different behavior of the current-voltage characteristics under uniaxial stress along[110] and[1 anti 10] directions is mainly determined by the arising piezoelectric field. The results are also discussed in terms of changes in the band structure under uniaxial compression. The construction of the cryostat for optical measurements under uniaxial stress at liquid nitrogen temperature is described in the paper. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Self-organized global control of carbon emissions

Science.gov (United States)

Zhao, Zhenyuan; Fenn, Daniel J.; Hui, Pak Ming; Johnson, Neil F.

2010-09-01

There is much disagreement concerning how best to control global carbon emissions. We explore quantitatively how different control schemes affect the collective emission dynamics of a population of emitting entities. We uncover a complex trade-off which arises between average emissions (affecting the global climate), peak pollution levels (affecting citizens’ everyday health), industrial efficiency (affecting the nation’s economy), frequency of institutional intervention (affecting governmental costs), common information (affecting trading behavior) and market volatility (affecting financial stability). Our findings predict that a self-organized free-market approach at the level of a sector, state, country or continent can provide better control than a top-down regulated scheme in terms of market volatility and monthly pollution peaks. The control of volatility also has important implications for any future derivative carbon emissions market.

Advanced CIDI Emission Control System Development

Energy Technology Data Exchange (ETDEWEB)

Lambert, Christine

2006-05-31

Ford Motor Company, with ExxonMobil and FEV, participated in the Department of Energy's (DOE) Ultra-Clean Transportation Fuels Program with the goal to develop an innovative emission control system for light-duty diesel vehicles. The focus on diesel engine emissions was a direct result of the improved volumetric fuel economy (up to 50%) and lower CO2 emissions (up to 25%) over comparable gasoline engines shown in Europe. Selective Catalytic Reduction (SCR) with aqueous urea as the NOx reductant and a Catalyzed Diesel Particulate Filter (CDPF) were chosen as the primary emission control system components. The program expected to demonstrate more than 90% durable reduction in particulate matter (PM) and NOx emissions on a light-duty truck application, based on the FTP-75 drive cycle. Very low sulfur diesel fuel (<15 ppm-wt) enabled lower PM emissions, reduced fuel economy penalty due to the emission control system and improved long-term system durability. Significant progress was made toward a durable system to meet Tier 2 Bin 5 emission standards on a 6000 lbs light-duty truck. A 40% reduction in engine-out NOx emissions was achieved with a mid-size prototype diesel engine through engine recalibration and increased exhaust gas recirculation. Use of a rapid warm-up strategy and urea SCR provided over 90% further NOx reduction while the CDPF reduced tailpipe PM to gasoline vehicle levels. Development work was conducted to separately improve urea SCR and CDPF system durability, as well as improved oxidation catalyst function. Exhaust gas NOx and ammonia sensors were also developed further. While the final emission control system did not meet Tier 2 Bin 5 NOx after 120k mi of aging on the dynamometer, it did meet the standards for HC, NMOG, and PM, and an improved SCR catalyst was shown to have potential to meet the NOx standard, assuming the DOC durability could be improved further. Models of DOC and SCR function were developed to guide the study of several key

The Electroluminescence Mechanism of Solution-Processed TADF Emitter 4CzIPN Doped OLEDs Investigated by Transient Measurements

Directory of Open Access Journals (Sweden)

Peng Wang

2016-10-01

Full Text Available High efficiency, solution-processed, organic light emitting devices (OLEDs, using a thermally-activated delayed fluorescent (TADF emitter, 1,2,3,5-tetrakis(carbazol-9-yl-4,6-dicyanobenzene (4CzIPN, are fabricated, and the transient electroluminescence (EL decay of the device with a structure of [ITO/PEDOT: PSS/4CzIPN 5 wt % doped 4,40-N,N0-dicarbazolylbiphenyl(CBP/bis-4,6-(3,5-di-4-pyridylphenyl-2-methylpyrimidine (B4PyMPM/lithium fluoride (LiF/Al], is systematically studied. The results shed light on the dominant operating mechanism in TADF-based OLEDs. Electroluminescence in the host–guest system is mainly produced from the 4CzIPN emitter, rather than the exciplex host materials.

Synthesis, characterization and electroluminescence of two highly-twisted non-doped blue light-emitting materials

Science.gov (United States)

Gong, Xiaojie; Pan, Yipeng; Xie, Xiang; Tong, Tong; Chen, Runfeng; Gao, Deqing

2018-04-01

Two pyrene derivatives, substituted with 2-methylnaphthalene units on 1,3-position and 1,6-position of pyrene backbones, were designed and synthesized. DFT calculation confirmed that the two molecules were highly twisted and the dihedral angles between pyrene backbone and naphthalene unit were over 80°, being attributed to the steric hindrance of ortho-methyl group and the substitution position of pyrene itself. As a result, the intermolecular aggregation was greatly inhibited in the solid state, being beneficial for suppressing the fluorescence quenching. By analyzing the optical and thermal properties, it was found that the π-π conjugation extension could be adjusted and a balance for high fluorescent efficiency and avoiding quenching at the same time could be reached, which may guide the molecular design in the future. The electroluminescence properties of the non-doped devices were enhanced with the double hole-transporting layers by optimizing the energy level matching. The stable blue EL emission, with the Commission Internationaled'Eclairage (CIEx,y) color coordinates of (0.15, 0.13) and (0.15, 0.11) at 7, 8, 9 and 10 V respectively, was obtained.

Light Emission by Nonequilibrium Bodies: Local Kirchhoff Law

Science.gov (United States)

Greffet, Jean-Jacques; Bouchon, Patrick; Brucoli, Giovanni; Marquier, François

2018-04-01

The goal of this paper is to introduce a local form of Kirchhoff law to model light emission by nonequilibrium bodies. While absorption by a finite-size body is usually described using the absorption cross section, we introduce a local absorption rate per unit volume and also a local thermal emission rate per unit volume. Their equality is a local form of Kirchhoff law. We revisit the derivation of this equality and extend it to situations with subsystems in local thermodynamic equilibrium but not in equilibrium between them, such as hot electrons in a metal or electrons with different Fermi levels in the conduction band and in the valence band of a semiconductor. This form of Kirchhoff law can be used to model (i) thermal emission by nonisothermal finite-size bodies, (ii) thermal emission by bodies with carriers at different temperatures, and (iii) spontaneous emission by semiconductors under optical (photoluminescence) or electrical pumping (electroluminescence). Finally, we show that the reciprocity relation connecting light-emitting diodes and photovoltaic cells derived by Rau is a particular case of the local Kirchhoff law.

High performance organic integrated device with ultraviolet photodetective and electroluminescent properties consisting of a charge-transfer-featured naphthalimide derivative

Energy Technology Data Exchange (ETDEWEB)

Wang, Hanyu; Wang, Xu; Yu, Junsheng, E-mail: luzhiyun@scu.edu.cn, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China, Chengdu 610054 (China); Zhou, Jie; Lu, Zhiyun, E-mail: luzhiyun@scu.edu.cn, E-mail: jsyu@uestc.edu.cn [College of Chemistry, Sichuan University, Chengdu 610064 (China)

2014-08-11

A high performance organic integrated device (OID) with ultraviolet photodetective and electroluminescent (EL) properties was fabricated by using a charge-transfer-featured naphthalimide derivative of 6-(3,5-bis-[9-(4-t-butylphenyl)-9H-carbazol-3-yl]-phenoxy)-2- (4-t-butylphenyl)-benzo[de]isoquinoline-1,3-dione (CzPhONI) as the active layer. The results showed that the OID had a high detectivity of 1.5 × 10{sup 11} Jones at −3 V under the UV-350 nm illumination with an intensity of 0.6 mW/cm{sup 2}, and yielded an exciplex EL light emission with a maximum brightness of 1437 cd/m{sup 2}. Based on the energy band diagram, both the charge transfer feature of CzPhONI and matched energy level alignment were responsible for the dual ultraviolet photodetective and EL functions of OID.

Solid immersion lenses for enhancing the optical resolution of thermal and electroluminescence mapping of GaN-on-SiC transistors

International Nuclear Information System (INIS)

Pomeroy, J. W.; Kuball, M.

2015-01-01

Solid immersion lenses (SILs) are shown to greatly enhance optical spatial resolution when measuring AlGaN/GaN High Electron Mobility Transistors (HEMTs), taking advantage of the high refractive index of the SiC substrates commonly used for these devices. Solid immersion lenses can be applied to techniques such as electroluminescence emission microscopy and Raman thermography, aiding the development device physics models. Focused ion beam milling is used to fabricate solid immersion lenses in SiC substrates with a numerical aperture of 1.3. A lateral spatial resolution of 300 nm is demonstrated at an emission wavelength of 700 nm, and an axial spatial resolution of 1.7 ± 0.3 μm at a laser wavelength of 532 nm is demonstrated; this is an improvement of 2.5× and 5×, respectively, when compared with a conventional 0.5 numerical aperture objective lens without a SIL. These results highlight the benefit of applying the solid immersion lenses technique to the optical characterization of GaN HEMTs. Further improvements may be gained through aberration compensation and increasing the SIL numerical aperture

Coal fired flue gas mercury emission controls

CERN Document Server

Wu, Jiang; Pan, Weiguo; Pan, Weiping

2015-01-01

Mercury (Hg) is one of the most toxic heavy metals, harmful to both the environment and human health. Hg is released into the atmosphere from natural and anthropogenic sources and its emission control has caused much concern. This book introduces readers to Hg pollution from natural and anthropogenic sources and systematically describes coal-fired flue gas mercury emission control in industry, especially from coal-fired power stations. Mercury emission control theory and experimental research are demonstrated, including how elemental mercury is oxidized into oxidized mercury and the effect of

Synthesis and Electroluminescent Properties of Julolidine-π-Juloidine Type Materials with the Bulky Adamantane Groups

Energy Technology Data Exchange (ETDEWEB)

Lee, Kum Hee; Yoon, Seung Soo [Sungkyunkwan Univ., Suwon (Korea, Republic of); Lee, Seok Jae; Kim, Young Kwan [Hongik Univ., Seoul (Korea, Republic of)

2012-11-15

A main problem of red emitting material, which contributes to their low EL performances, is the concentration quenching due to the effective self aggregation and the consequent formation of excimers. To avoid this drawback and thus improve the EL properties of red fluorescent OLED devices, many synthetic efforts have been conducted to develop new emitting materials with the structural motifs to suppress self-aggregation by the weakening intermolecular attractive interactions. Particularly, the introduction of bulky moieties in the emitters would provide the steric hindrance between emitting materials in solid state devices and thus reduce the self-aggregation. Nevertheless, EL performances of red materials still need to be improved for the practical applications. In conclusion, we designed and synthesized three julolidine-π-juloidine type emitting materials (1-3) with the bulky adamantane groups. To study their electroluminescent properties, the multilayered OLED devices with the structure of ITO/NPB (40 nm)/ADN : 1-3 (x%) (20 nm)/Alq{sub 3} (40 nm)/Liq (2 nm)/Al were fabricated. All devices using emitters 1-3 showed the efficient emissions, in which their EL performances depend on the structure of emitters sensitively. Particularly, a device using emitter 3 exhibited the efficient orange-red emission with the luminous and power efficiencies of 4.79 cd/A and 1.76 lm/W at 20 mA/cm{sup 2}, respectively. The CIE coordinates of this device was (0.57, 0.42) at 7.0 V.

Exciton-dominant Electroluminescence from a Diode of Monolayer MoS2

Science.gov (United States)

2014-05-14

injected electrons and holes, is a reliable technique to study exciton recombination processes in monolayer MoS2, including val- ley and spin excitation...temperature. After superimposing a white light scattering image of the de - vice, we find that the electroluminescence is localized at the edge of the...We find the emerged feature (labeled NX) peaks at 550 nm with energy of 2.255 eV. In low dimensional system, like monolayer MoS2, Coulomb interactions

Molding resonant energy transfer by colloidal crystal: Dexter transfer and electroluminescence

Science.gov (United States)

González-Urbina, Luis; Kolaric, Branko; Libaers, Wim; Clays, Koen

2010-05-01

Building photonic crystals by combination of colloidal ordering and metal sputtering we were able to construct a system sensitive to an electrical field. In corresponding crystals we embedded the Dexter pair (Ir(ppy3) and BAlq) and investigated the influence of the band gap on the resonant energy transfer when the system is excited by light and by an electric field respectively. Our investigations extend applications of photonic crystals into the field of electroluminescence and LED technologies.

An electroluminescence device for printable electronics using coprecipitated ZnS:Mn nanocrystal ink

International Nuclear Information System (INIS)

Toyama, T; Hama, T; Adachi, D; Nakashizu, Y; Okamoto, H

2009-01-01

Electroluminescence (EL) devices for printable electronics using coprecipitated ZnS:Mn nanocrystal (NC) ink are demonstrated. The EL properties of these devices were investigated along with the structural and optical properties of ZnS:Mn NCs with an emphasis on their dependence on crystal size. Transmission electron microscopy and x-ray diffraction studies revealed that the NCs, with a crystal size of 3-4 nm, are nearly monodisperse; the crystal size can be controlled by the Zn 2+ concentration in the starting solution for coprecipitation. The results of optical studies indicate the presence of quantum confinement effects; in addition, the NC surfaces are well passivated, regardless of the crystal size. Finally, an increase in the luminance of EL devices with a decrease in crystal size is observed, which suggests the excitation mechanism of ZnS:Mn NC EL devices.

Synthesis and Electroluminescence Properties of 3-(Trifluoromethylphenyl-Substituted 9,10-Diarylanthracene Derivatives for Blue Organic Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Sang Woo Kwak

2017-10-01

Full Text Available Diaryl-substituted anthracene derivatives containing 3-(trifluoromethylphenyl groups, 9,10-diphenyl-2-(3-(trifluoromethylphenylanthracene (1, 9,10-di([1,1′-biphenyl]-4-yl-2-(3-(trifluoromethylphenylanthracene (2, and 9,10-di(naphthalen-2-yl-2-(3-(trifluoromethylphenylanthracene (3 were synthesized and characterized. The compounds 1–3 possessed high thermal stability and proper frontier-energy levels, which make them suitable as host materials for blue organic light-emitting diodes. The electroluminescent (EL emission maximum of the three N,N-diphenylamino phenyl vinyl biphenyl (DPAVBi-doped (8 wt % devices for compounds 1–3 was exhibited at 488 nm (for 1 and 512 nm (for 2 and 3. Among them, the 1-based device displayed the highest device performances in terms of brightness (Lmax = 2153.5 cd·m−2, current efficiency (2.1 cd·A−1, and external quantum efficiency (0.8%, compared to the 2- and 3-based devices.

Ultraviolet electroluminescence from nitrogen-doped ZnO-based heterojuntion light-emitting diodes prepared by remote plasma in situ atomic layer-doping technique.

Science.gov (United States)

Chien, Jui-Fen; Liao, Hua-Yang; Yu, Sheng-Fu; Lin, Ray-Ming; Shiojiri, Makoto; Shyue, Jing-Jong; Chen, Miin-Jang

2013-01-23

Remote plasma in situ atomic layer doping technique was applied to prepare an n-type nitrogen-doped ZnO (n-ZnO:N) layer upon p-type magnesium-doped GaN (p-GaN:Mg) to fabricate the n-ZnO:N/p-GaN:Mg heterojuntion light-emitting diodes. The room-temperature electroluminescence exhibits a dominant ultraviolet peak at λ ≈ 370 nm from ZnO band-edge emission and suppressed luminescence from GaN, as a result of the decrease in electron concentration in ZnO and reduced electron injection from n-ZnO:N to p-GaN:Mg because of the nitrogen incorporation. The result indicates that the in situ atomic layer doping technique is an effective approach to tailoring the electrical properties of materials in device applications.

Effect of resonant tunneling on electroluminescence in nc-Si/SiO2 multilayers-based p-i-n structure

International Nuclear Information System (INIS)

Chen, D.Y.; Wang, Y.Y.; Sun, Y.; He, Y.J.; Zhang, G.

2015-01-01

P-i-n structures with SiO 2 /nc-Si/SiO 2 multilayers as intrinsic layer were prepared in conventional plasma enhanced chemical vapor deposition system. Their carrier transport and electroluminescence properties were investigated. Two resonant tunneling related current peaks with current dropping gradually under forward bias were observed in the current voltage curve. Non-uniformity of the interfaces might be responsible for the gradual dropping of the current. Electroluminescence intensity of the device under bias of 7 V which is near the resonant tunneling peak voltage of 7.2 V was weaker than that under 6.5 V. According to the Gaussian fitting results of the spectra, the intensity of the sub-peak of 650 nm originating from recombination of injected electrons and holes was decreased the most. When resonant tunneling conditions are met, it might be that most of the injected electrons participate in resonant tunneling and fewer in Pool–Frenkel tunneling, which is the main carrier transport mechanism, to contribute to electroluminescence intensity. - Highlights: • Two resonant tunneling peaks with current dropping gradually were observed. • The EL intensity of the structure under resonant tunneling peak voltage is weakened. • P–F tunneling is the main transport mechanism besides resonant tunneling

Design and development of low-power driven hybrid electroluminescent lamp from carbon nanotube embedded phosphor material

International Nuclear Information System (INIS)

Yadav, Deepika; Mishra, Savvi; Shanker, Virendra; Haranath, D.

2013-01-01

Highlights: •We are first to report CNT embedded ZnS:Mn hybrid EL system. •Achieved efficient orange-red EL emission at low operating voltages ( AC ). •Facile technique to induce conductive paths inside the ZnS particle to trigger EL. •Detailed electrical characterization of EL lamp is presented. -- Abstract: We present a novel methodology to design a hybrid electroluminescent (EL) lamp by embedding carbon nanotubes (CNTs) inside the ZnS:Mn phosphor particles by conventional solid state diffusion technique. By doing so, the phosphor particles exhibited increase in EL brightness and efficiency at low operating voltages ( AC ). Interestingly, shorter the length of CNTs used, greater was the field enhancement effect and lower was the operating voltages to glow the EL lamps. The role of CNTs have been identified to form conductive paths inside the ZnS particle thereby triggering EL due to electron injection to luminescent centers (Mn 2+ ) at nominal voltages. In addition, a detailed electrical characterization of the novel EL lamp along with its spectral energy distribution studies are presented

Electroluminescence from single nanowires by tunnel injection: an experimental study

International Nuclear Information System (INIS)

Zimmler, Mariano A; Bao Jiming; Shalish, Ilan; Yi, Wei; Yoon, Joonah; Narayanamurti, Venkatesh; Capasso, Federico

2007-01-01

We present a hybrid light-emitting diode structure composed of an n-type gallium nitride nanowire on a p-type silicon substrate in which current is injected along the length of the nanowire. The device emits ultraviolet light under both bias polarities. Tunnel injection of holes from the p-type substrate (under forward bias) and from the metal (under reverse bias) through thin native oxide barriers consistently explains the observed electroluminescence behaviour. This work shows that the standard p-n junction model is generally not applicable to this kind of device structure

Electroluminescence Caused by the Transport of Interacting Electrons through Parallel Quantum Dots in a Photon Cavity

Science.gov (United States)

Gudmundsson, Vidar; Abdulla, Nzar Rauf; Sitek, Anna; Goan, Hsi-Sheng; Tang, Chi-Shung; Manolescu, Andrei

2018-02-01

We show that a Rabi-splitting of the states of strongly interacting electrons in parallel quantum dots embedded in a short quantum wire placed in a photon cavity can be produced by either the para- or the dia-magnetic electron-photon interactions when the geometry of the system is properly accounted for and the photon field is tuned close to a resonance with the electron system. We use these two resonances to explore the electroluminescence caused by the transport of electrons through the one- and two-electron ground states of the system and their corresponding conventional and vacuum electroluminescense as the central system is opened up by coupling it to external leads acting as electron reservoirs. Our analysis indicates that high-order electron-photon processes are necessary to adequately construct the cavity-photon dressed electron states needed to describe both types of electroluminescence.

Towards an Integrated Assessment Model for Tropospheric Ozone-Emission Inventories, Scenarios and Emission-control Options

OpenAIRE

Olsthoorn, X.

1994-01-01

IIASA intends to extend its RAINS model for addressing the issue of transboundary ozone air pollution. This requires the development of a VOC-emissions module, VOCs being precursors in ozone formation. The module should contain a Europe-wide emission inventory, a submodule for developing emission scenarios and a database of measures for VOC-emission control, including data about control effectiveness and control costs. It is recommended to use the forthcoming CORINAIR90 inventory for construc...

Efficient red organic electroluminescent devices based on trivalent europium complex obtained by designing the device structure with stepwise energy levels

Energy Technology Data Exchange (ETDEWEB)

Zhou, Liang; Jiang, Yunlong; Cui, Rongzhen; Li, Yanan; Zhao, Xuesen; Deng, Ruiping; Zhang, Hongjie, E-mail: hongjie@ciac.ac.cn

2016-02-15

In this study, we aim to further enhance the electroluminescence (EL) performances of trivalent europium complex Eu(TTA){sub 3}phen (TTA=thenoyltrifluoroacetone and phen=1,10-phenanthroline) by designing the device structure with stepwise energy levels. The widely used bipolar material 2,6-bis(3-(9H-carbazol-9-yl)phenyl)pyridine (26DCzPPy) was chosen as host material, while the doping concentration of Eu(TTA){sub 3}phen was optimized to be 4%. To facilitate the injection and transport of holes, MoO{sub 3} anode modification layer and 4,4′,4′′-Tris(carbazole-9-yl)triphenylamine (TcTa) hole transport layer were inserted in sequence. Efficient pure red emission with suppressed efficiency roll-off was obtained attributed to the reduction of accumulation holes, the broadening of recombination zone, and the improved balance of holes and electrons on Eu(TTA){sub 3}phen molecules. Finally, the device with 3 nm MoO{sub 3} and 5 nm TcTa obtained the highest brightness of 3278 cd/m{sup 2}, current efficiency of 12.45 cd/A, power efficiency of 11.50 lm/W, and external quantum efficiency of 6.60%. Such a device design strategy helps to improve the EL performances of emitters with low-lying energy levels and provides a chance to simplify device fabrication processes. - Highlights: • Electroluminescent performances of europium complex were further improved. • Device structure with stepwise energy levels was designed. • Better carriers' balance was realized by improving the injection and transport of holes. • The selection of bipolar host caused the broadening of recombination zone.

The effect of electric field strength on electroplex emission at the interface of NPB/PBD organic light-emitting diodes

Science.gov (United States)

Zhao, De-Wei; Xu, Zheng; Zhang, Fu-Jun; Song, Shu-Fang; Zhao, Su-Ling; Wang, Yong; Yuan, Guang-Cai; Zhang, Yan-Fei; Xu, Hong-Hua

2007-02-01

Organic light-emitting diode (OLED) based on two kinds of blue emission materials N, N'-bis(1-naphthyl)- N, N'-diphenyl-l,l'-diphenyl-4,4'-diamine (NPB) and 2-(4-biphenylyl)-5(4- tert-butyl-phenyl)-1,3,4-oxadiazole (PBD) was fabricated. There is only one emission peak in photoluminescence (PL) spectrum which originates from NPB exciton emission. And the electroluminescence (EL) emission peaks have an apparent red-shift with the increase of driving voltage. The red-shift emission from exciplex emission could be ruled out. Thus, by the method of Gaussian fitting it should be ascribed to the overlap of exciton emission and electroplex emission which occurs at the interface between NPB and PBD. The formation of the electroplex emission under high electric field is analyzed.

NOx and N2O emission control with catalyst's

International Nuclear Information System (INIS)

Hiltunen, M.

1994-01-01

Due to the increasingly stringent emission regulations, new technologies are needed to be developed for improving emission control in circulating fluidized-bed boilers. The objective of this project is to test the concept of using catalysts for NO x and N 2 O emission control. N 2 O emission is in the range of 30 - 100 ppm from fluidized bed combustors burning coal. Since it is a greenhouse gas an effective means of controlling N 2 O emission is needed

Control of volatile organic compound emissions: the issues

Energy Technology Data Exchange (ETDEWEB)

Woodfield, M.; Marlowe, I.

1989-11-01

This review paper outlines the problems caused by the emissions of volatile organic compounds (VOC) which are causing increasing concern because of their part in the formation of photochemical oxidation that causes damage to crops and vegetation and because of the toxic and climatic effects. It briefly summarises current knowledge of VOC emissions and their effects and then suggests options for abatement of VOC emissions in the UK and the EEC. A comparison of anthropogenic VOC emission in the UK and the EEC from various sources is given. Further information is needed on current emissions, on the costs and efficiencies of control technologies and on the effects of control on industry before decisions can be made on the suitability, extent and strategy to control VOC emissions in the UK. The report was prepared for the UK Department of Trade and Industry (Headquarters).

Evaporation Controlled Emission in Ventilated Rooms

DEFF Research Database (Denmark)

Topp, Claus; Nielsen, Peter V.; Heiselberg, Per

-scale ventilated room when the emission is fully or partly evaporation controlled. The objective of the present research work has been to investigate the change of emission rates from small-scale experiments to full-scale ventilated rooms and to investigate the influence of the local air velocity field near......Emission of volatile organic compounds (VOCs) from materials is traditionally determined from tests carried out in small-scale test chambers. However, a difference in scale may lead to a difference in the measured emission rate in a small-scale test chamber and the actual emission rate in a full...

Study of structural, morphological, optical and electroluminescent properties of undoped ZnO nanorods grown by a simple chemical precipitation

Directory of Open Access Journals (Sweden)

Singh A.

2015-12-01

Full Text Available In this work, zinc oxide (ZnO nanorods were obtained by a simple chemical precipitation method in the presence of capping agent: polyvinyl pyrrolidone (PVP at room temperature. X-ray diffraction (XRD result indicates that the synthesized undoped ZnO nanorods have hexagonal wurtzite structure without any impurities. It has been observed that the growth direction of the prepared ZnO nanorods is [1 0 1]. XRD analysis revealed that the nanorods have the crystallite size of 49 nm. Crystallite size is calculated by Debye-Scherrer formula and lattice strain is calculated by Williomson-Hall equation. Cell volume, Lorentz factor, Lorentz polarization factor, bond length, texture coefficient, lattice constants and dislocation density have also been studied. We also compared the interplanar spacings and relative peak intensities with their standard values at different angles. The scanning electron microscope (SEM images confirmed the size and shape of these nanorods. It has been found that the diameter of the nanorods ranges from 1.52 μm to 1.61 μm and the length is about 4.89 μm. It has also been observed that at room temperature ultraviolet visible (UV-Vis absorption band is around 355 nm (blue shifted as compared to the bulk. The average particle size has also been calculated by mathematical model of effective mass approximation equation, using UV-Vis absorption peak. Finally, the bandgap has been calculated using UV-absorption peak. Electroluminescence (EL studies show that emission of light is possible at very small threshold voltage and it increases rapidly with increasing applied voltage. It is seen that smaller ZnO nanoparticles give higher electroluminescence brightness starting at lower threshold voltage. The brightness is also affected by increasing the frequency of AC signal.

Electrically induced spontaneous emission in open electronic system

Science.gov (United States)

Wang, Rulin; Zhang, Yu; Yam, Chiyung; Computation Algorithms Division (CSRC) Team; Theoretical; Computational Chemistry (HKU) Collaboration

A quantum mechanical approach is formulated for simulation of electroluminescence process in open electronic system. Based on nonequilibrium Green's function quantum transport equations and combining with photon-electron interaction, this method is used to describe electrically induced spontaneous emission caused by electron-hole recombination. The accuracy and reliability of simulation depends critically on correct description of the electronic band structure and the electron occupancy in the system. In this work, instead of considering electron-hole recombination in discrete states in the previous work, we take continuous states into account to simulate the spontaneous emission in open electronic system, and discover that the polarization of emitted photon is closely related to its propagation direction. Numerical studies have been performed to silicon nanowire-based P-N junction with different bias voltage.

Bifunctional electroluminescent and photovoltaic devices using bathocuproine as electron-transporting material and an electron acceptor

Energy Technology Data Exchange (ETDEWEB)

Chen, L.L. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing, 100039 (China); Institute of Functional Material Chemistry, Faculty of Chemistry, Northeast Normal University, Changchun, 130024 (China); Li, W.L. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China)]. E-mail: wllioel@yahoo.com.cn; Li, M.T. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing, 100039 (China); Chu, B. [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, 130033 (China)

2007-01-15

Electroluminescence (EL) devices, using 4, 4',4''-tris (2-methylphenyl- phenylamino) triphenylamine (m-MTDATA) as hole-transporting material and bathocuproine (BCP) as an electron-transporting material, were fabricated, which emitted bright green light peaked at 520 nm instead of the emission of m-MTDATA or BCP. It was attributed to the exciplex formation and emission at the interface of m-MTDATA and BCP. EL performance was significantly enhanced by a thin mixed layer (5 nm) of m-MTDATA and BCP inserted between the two organic layers of the original m-MTDATA/BCP bilayer device. The trilayer device showed maximum luminance of 1,205 cd/m{sup 2} at 8 V. At a luminance of 100 cd/m{sup 2}, the power efficiency is 1.64 cd/A. Commission International De L'Eclairoge (CIE) color coordinates of the output spectrum of the devices at 8 V are x=0.244 and y=0.464. These devices also showed photovoltaic (PV) properties, which were sensitive to UV light. The PV diode exhibits high open-circuit voltage (V {sub oc}) of 2.10 V under illumination of 365 nm UV light with 2 mW/cm{sup 2}. And the short-circuit current (I {sub sc}) of 92.5x10{sup -6} A/cm{sup 2}, fill factor (FF) of 0.30 and power conversion efficiency ({eta} {sub e}) of 2.91% are respectively achieved. It is considered that strong exciplex emission in an EL device is a good indicator of efficient charge transfer at the organic interface, which is a basic requirement for good PV performance. Both the bilayer and trilayer devices showed EL and PV properties, suggesting their potential use as multifunction devices.

VOC emissions control systems

International Nuclear Information System (INIS)

Spessard, J.E.

1993-01-01

The air pollution control equipment marketplace offers many competing technologies for controlling emissions of volatile organic compounds (VOC) in air. If any technology was economically and technically superior under all conditions, it would be the only one on the market. In fact, each technology used to control VOCs is superior under some set of conditions. The reasons for choosing one control technology over another are situation-specific. Some general guidelines to VOC control technologies and the situations where each may be appropriate are presented in this article. The control technologies and applications are summarized in a table

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

Science.gov (United States)

de Vos, Marc; Torah, Russel; Tudor, John

2016-04-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps.

First observation of liquid-xenon proportional electroluminescence in THGEM holes

International Nuclear Information System (INIS)

Arazi, L; Itay, R; Landsman, H; Levinson, L; Pasmantirer, B; Rappaport, M L; Vartsky, D; Breskin, A; Coimbra, A E C

2013-01-01

Radiation-induced proportional-electroluminescence UV signals, emitted from the holes of a Thick Gas Electron Multiplier (THGEM) electrode immersed in liquid xenon, were recorded with a PMT for the first time. Significant photon yields were observed with gamma photons and alpha particles using a 0.4 mm thick electrode with 0.3 mm diameter holes; at 2 kV across the THGEM the photon yield was estimated to be ∼ 600 UV photons/electron over 4π. This may pave the way towards the realization of novel single-phase noble-liquid radiation detectors incorporating liquid hole-multipliers (LHM); their concept is presented

Dispenser printed electroluminescent lamps on textiles for smart fabric applications

International Nuclear Information System (INIS)

De Vos, Marc; Torah, Russel; Tudor, John

2016-01-01

Flexible electroluminescent (EL) lamps are fabricated onto woven textiles using a novel dispenser printing process. Dispenser printing utilizes pressurized air to deposit ink onto a substrate through a syringe and nozzle. This work demonstrates the first use of this technology to fabricate EL lamps. The luminance of the dispenser printed EL lamps is compared to screen-printed EL lamps, both printed on textile, and also commercial EL lamps on polyurethane film. The dispenser printed lamps are shown to have a 1.5 times higher luminance than the best performing commercially available lamp, and have a comparable performance to the screen-printed lamps. (paper)

Economic growth and carbon emission control

Science.gov (United States)

Zhang, Zhenyu

The question about whether environmental improvement is compatible with continued economic growth remains unclear and requires further study in a specific context. This study intends to provide insight on the potential for carbon emissions control in the absence of international agreement, and connect the empirical analysis with theoretical framework. The Chinese electricity generation sector is used as a case study to demonstrate the problem. Both social planner and private problems are examined to derive the conditions that define the optimal level of production and pollution. The private problem will be demonstrated under the emission regulation using an emission tax, an input tax and an abatement subsidy respectively. The social optimal emission flow is imposed into the private problem. To provide tractable analytical results, a Cobb-Douglas type production function is used to describe the joint production process of the desired output and undesired output (i.e., electricity and emissions). A modified Hamiltonian approach is employed to solve the system and the steady state solutions are examined for policy implications. The theoretical analysis suggests that the ratio of emissions to desired output (refer to 'emission factor'), is a function of productive capital and other parameters. The finding of non-constant emission factor shows that reducing emissions without further cutting back the production of desired outputs is feasible under some circumstances. Rather than an ad hoc specification, the optimal conditions derived from our theoretical framework are used to examine the relationship between desired output and emission level. Data comes from the China Statistical Yearbook and China Electric Power Yearbook and provincial information of electricity generation for the year of 1993-2003 are used to estimate the Cobb-Douglas type joint production by the full information maximum likelihood (FIML) method. The empirical analysis shed light on the optimal

White emission via electroplex formation at poly( N-vinylcarbazole)/2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline interface

Science.gov (United States)

Wang, Yuan-Min; Teng, Feng; Xu, Zheng; Hou, Yan-Bing; Yang, Sheng-Yi; Qian, Lei; Zhang, Ting; Liu, De-Ang

2004-09-01

The photoluminescence (PL) and electroluminescence (EL) properties of OLEDs based on poly( N-vinylcarbazole)(PVK) and 2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) have been studied. A new emission at 595 nm has been observed in EL spectra but not in PL spectra of the devices. We suggest the new emission originates from the electroplex occuring at PVK-BCP interface. White emission via electroplex has been obtained in all the OLEDs. CIE coordinates of device ITO/PEDOT:PSS/PVK/BCP/Alq 3/LiF/Al is (0.31, 0.33) at 18 V. Alq 3 layer plays an important role in tuning the recombination zone and enhancing the electroplex emission.

Light Emission by Nonequilibrium Bodies: Local Kirchhoff Law

Directory of Open Access Journals (Sweden)

Jean-Jacques Greffet

2018-04-01

Full Text Available The goal of this paper is to introduce a local form of Kirchhoff law to model light emission by nonequilibrium bodies. While absorption by a finite-size body is usually described using the absorption cross section, we introduce a local absorption rate per unit volume and also a local thermal emission rate per unit volume. Their equality is a local form of Kirchhoff law. We revisit the derivation of this equality and extend it to situations with subsystems in local thermodynamic equilibrium but not in equilibrium between them, such as hot electrons in a metal or electrons with different Fermi levels in the conduction band and in the valence band of a semiconductor. This form of Kirchhoff law can be used to model (i thermal emission by nonisothermal finite-size bodies, (ii thermal emission by bodies with carriers at different temperatures, and (iii spontaneous emission by semiconductors under optical (photoluminescence or electrical pumping (electroluminescence. Finally, we show that the reciprocity relation connecting light-emitting diodes and photovoltaic cells derived by Rau is a particular case of the local Kirchhoff law.

A novel electroluminescent PPV copolymer and silsesquioxane nanocomposite film for the preparation of efficient PLED devices.

Science.gov (United States)

Venegoni, Ivan; Carniato, Fabio; Olivero, Francesco; Bisio, Chiara; Pira, Nello Li; Lambertini, Vito Guido; Marchese, Leonardo

2012-11-02

Polymer light-emitting diodes (PLEDs) have attracted growing interest in recent years for their potential use in displays and lighting fields. Nevertheless, PLED devices have some disadvantages in terms of low optoelectronic efficiency, high cost, short lifetimes and low thermal stability, which limit their final applications. Huge efforts have been made recently to improve the performances of these devices. The addition of inorganic or hybrid organic-inorganic nanoparticles to the light-emitting polymers, for example, allows their thermal stability and electroluminescent efficiency to be increased. Following this approach, novel PLED devices based on composite films of PPV-derivative copolymer (commercial name Super Yellow, SY) and octaisobutil POSS, were developed in this study. The device containing Super Yellow loaded with 1 wt% of POSS showed higher efficiency (ca. +30%) and improved lifetime in comparison to PLED prepared with the pure electroluminescent polymer. The PLED devices developed in this study are suitable candidates for automotive dashboards and, in general, for lighting applications.

Tunable light emission by exciplex state formation between hybrid halide perovskite and core/shell quantum dots: Implications in advanced LEDs and photovoltaics

Science.gov (United States)

Sanchez, Rafael S.; de la Fuente, Mauricio Solis; Suarez, Isaac; Muñoz-Matutano, Guillermo; Martinez-Pastor, Juan P.; Mora-Sero, Ivan

2016-01-01

We report the first observation of exciplex state electroluminescence due to carrier injection between the hybrid lead halide perovskite (MAPbI3–xClx) and quantum dots (core/shell PbS/CdS). Single layers of perovskite (PS) and quantum dots (QDs) have been produced by solution processing methods, and their photoluminescent properties are compared to those of bilayer samples in both PS/QD and QD/PS configurations. Exciplex emission at lower energies than the band gap of both PS and QD has been detected. The exciplex emission wavelength of this mixed system can be simply tuned by controlling the QD size. Light-emitting diodes (LEDs) have been fabricated using those configurations, which provide light emission with considerably low turn-on potential. The “color” of the LED can also be tuned by controlling the applied bias. The presence of the exciplex state PS and QDs opens up a broad range of possibilities with important implications not only in tunable LEDs but also in the preparation of intermediate band gap photovoltaic devices with the potentiality of surpassing the Shockley-Queisser limit. PMID:26844299

Palladium-based on-wafer electroluminescence studies of GaN-based LED structures

Energy Technology Data Exchange (ETDEWEB)

Salcianu, C.O.; Thrush, E.J.; Humphreys, C.J. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Plumb, R.G. [Centre for Photonic Systems, Department of Engineering, University of Cambridge, Cambridge CB3 0FD (United Kingdom); Boyd, A.R.; Rockenfeller, O.; Schmitz, D.; Heuken, M. [AIXTRON AG, Kackertstr. 15-17, 52072 Aachen (Germany)

2008-07-01

Electroluminescence (EL) testing of Light Emitting Diode (LED) structures is usually done at the chip level. Assessing the optical and electrical properties of LED structures at the wafer scale prior to their processing would improve the cost effectiveness of producing LED-lamps. A non-destructive method for studying the luminescence properties of the structure at the wafer-scale is photoluminescence (PL). However, the relationship between the on-wafer PL data and the final device EL can be less than straightforward (Y. H Aliyu et al., Meas. Sci. Technol. 8, 437 (1997)) as the two techniques employ different carrier injection mechanisms. This paper provides an overview of some different techniques in which palladium is used as a contact in order to obtain on-wafer electroluminescence information which could be used to screen wafers prior to processing into final devices. Quick mapping of the electrical and optical characteristics was performed using either palladium needle electrodes directly, or using the latter in conjunction with evaporated palladium contacts to inject both electrons and holes into the active region via the p-type capping layer of the structure. For comparison, indium was also used to make contact to the n-layer so that electrons could be directly injected into that layer. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Controlling fugitive emissions from mechanical seals

International Nuclear Information System (INIS)

Adams, W.V.

1992-01-01

This paper reports that enactment of the 1990 Federal Clean Air Amendments will sharply focus efforts in the process industries to reduce fugitive emissions. Moreover, state and local governments may be imposing stricter laws and regulations which will affect allowable fugitive emissions from U.S. refineries and process plants. Plants outside the U.S. have similar concerns. Clearly, mechanical seals for process pumps represent an enormous population and is one category of equipment destined for careful evaluation as a means to control fugitive emissions. Fugitive are unintentional emissions from valves, pumps, flanges, compressors, etc., as opposed to point-source emissions from stacks, vents and flares. Fugitive emissions do not occur as a part of normal plant operations, but result from the effects of: Malfunctions, Age, Lack of proper maintenance, Operator error, Improper equipment specification, Use of inferior technology, and externally caused damage

Control mechanisms for Nordic ship emissions

Energy Technology Data Exchange (ETDEWEB)

Martinsen, K. [DNV, Oslo (Norway); Torvanger, A. [Cicero, Oslo (Norway)

2013-04-15

Shipping today operates under a complex set of international and domestic regulations. However, the environmental regulations have lagged behind those of other industries. This situation is now changing quite dramatically. The increased focus on environmental issues, combined with the growing realisation of the actual pollution burden imposed by shipping, has led to an upsurge in both international and national regulations. Some are ready and will enter into force in the near future, while others are still being developed. On behalf of the Nordic Council of Ministers DNV has carried out a study on possible control mechanisms for Nordic ship emission. The aim is to assess the baseline shipping emissions and reduction potential and the possible controlling mechanisms (both incentives and regulations) available for reducing the emissions to air from shipping within the Nordic region. (Author)

Electroluminescence of organic light-emitting diodes with an ultra-thin layer of dopant

Energy Technology Data Exchange (ETDEWEB)

Li Weizhi [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Yu Junsheng [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jsyu@uestc.edu.cn; Wang, Tao [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Jiang, Yadong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jiangyd@uestc.edu.cn; Wei, Bangxiong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2008-03-15

Conventional fluorescent dyes, i.e., 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), 5,12-dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA) and 5,6,11,12-tetraphenylnaphthacene (Rubrene), were used to investigate the performance of organic light-emitting diodes (OLEDs) based on indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine (NPB)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3})/MgAg. The dyes were either inserted into devices as an ultra-thin film at the NPB/Alq{sub 3} interface by sequential evaporation, or doped into the Alq{sub 3} emission layer by co-evaporation with the doping ratio about 2%. Electroluminescence (EL) spectra of devices indicated that concentration quenching effect (CQE) of the dye-dopant was slightly bigger in the former than in the latter, while the degrees of CQE for three dopants are in the order of DMQA > DCJTB > Rubrene suggested by the difference in EL spectra and performances of devices. In addition, EL process of device with an ultra-thin layer of dopant is dominated by direct carrier trapping (DCT) process due to almost no holes recombine with electrons in Alq{sub 3}-host layer.

Synthesis of organic EL materials with cyano group and evaluation of emission characteristics in organic EL devices

International Nuclear Information System (INIS)

Kim, Dong Uk

1999-01-01

Nobel electroluminescent materials, polymer material, PU-BCN and low molar mass material, D-BCN with the same chromophores were designed and synthesized. A molecular structure of chromophore was composed of bisstyrylbenzene derivative with cyano groups as electron injection and transport and phenylamine groups as hole injection and transport. Device structures with PU-BCN and D-BCN as an emission layer were fabricated, which were a single-layer device(SL), Indium-tin oxide(ITO)/emission layer/MgAg, and two kinds of double-layer devices which were composed of ITO/emission layer/oxadiazole derivative/MgAg as a DL-E device and ITO/triphenylamine derivative/emission layer/MgAg as a DL-H device. The two emission materials, PU-BCN and D-BCN with the same emission-chromophore were evaluated as having excellent performance of charge injection and transport and revealed almost the same emission characteristics in high current density. EL emission maximum peaks of two material were detected at about 640 nm wavelength of red emission region

Exciplex emission and decay of co-deposited 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

Science.gov (United States)

Huang, Qingyu; Zhao, Suling; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian

2014-04-01

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4',4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl)mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m2, as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m-2. The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence.

Magnetically modulated electroluminescence from hybrid organic/inorganic light-emitting diodes based on electron donor-acceptor exciplex blends

Science.gov (United States)

Pang, Zhiyong; Baniya, Sangita; Zhang, Chuang; Sun, Dali; Vardeny, Z. Valy

2016-03-01

We report room temperature magnetically modulated electroluminescence from a hybrid organic/inorganic light-emitting diode (h-OLED), in which an inorganic magnetic tunnel junction (MTJ) with large room temperature magnetoresistance is coupled to an N,N,N ',N '-Tetrakis(4-methoxyphenyl)benzidine (MeO-TPD): tris-[3-(3-pyridyl)mesityl]borane (3TPYMB) [D-A] based OLED that shows thermally activated delayed luminescence. The exciplex-based OLED provides two spin-mixing channels: upper energy channel of polaron pairs and lower energy channel of exciplexes. In operation, the large resistance mismatch between the MTJ and OLED components is suppressed due to the non-linear I-V characteristic of the OLED. This leads to enhanced giant magneto-electroluminescence (MEL) at room temperature. We measured MEL of ~ 75% at ambient conditions. Supported by SAMSUNG Global Research Outreach (GRO) program, and also by the NSF-Material Science & Engineering Center (MRSEC) program at the University of Utah (DMR-1121252).

White emission from nano-structured top-emitting organic light-emitting diodes based on a blue emitting layer

International Nuclear Information System (INIS)

Hyun, Woo Jin; Park, Jung Jin; Park, O Ok; Im, Sang Hyuk; Chin, Byung Doo

2013-01-01

We demonstrated that white emission can be obtained from nano-structured top-emitting organic light-emitting diodes (TEOLEDs) based on a blue emitting layer (EML). The nano-structured TEOLEDs were fabricated on nano-patterned substrates, in which both optical micro-cavity and scattering effects occur simultaneously. Due to the combination of these two effects, the electroluminescence spectra of the nano-structured device with a blue EML exhibited not only blue but also yellow colours, which corresponded to the intrinsic emission of the EML and the resonant emission of the micro-cavity effect. Consequently, it was possible to produce white emission from nano-structured TEOLEDs without employing a multimode micro-cavity. The intrinsic emission wavelength can be varied by altering the dopant used for the EML. Furthermore, the emissive characteristics turned out to be strongly dependent on the nano-pattern sizes of the nano-structured devices. (paper)

Exciplex emission and decay of co-deposited 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

Energy Technology Data Exchange (ETDEWEB)

Huang, Qingyu; Zhao, Suling, E-mail: slzhao@bjtu.edu.cn; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Beijing Jiaotong University, Beijing 100044 (China); Institute of Optoelectronics Technology, Beijing Jiaotong University, Beijing 100044 (China)

2014-04-21

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m{sup 2}, as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m{sup −2}. The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence.

Exciplex emission and decay of co-deposited 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane organic light-emitting devices with different electron transporting layer thicknesses

International Nuclear Information System (INIS)

Huang, Qingyu; Zhao, Suling; Xu, Zheng; Fan, Xing; Shen, Chongyu; Yang, Qianqian

2014-01-01

Highly efficient fluorescence organic light-emitting diodes (OLEDs) based on the mixed 4,4′,4″-tris[3-methylphenyl(phenyl)amino]triphenylamine:tris-[3-(3-pyridyl) mesityl]borane (1:1) system are reported. The electroluminescence due to the exciplex emission is red shifted when the thickness of the electron-transporting layer increases. The prepared OLEDs achieve a low turn-on voltage of 2.1 V, a high current efficiency of 36.79 cd/A, and a very high luminescence of 17 100 cd/m 2 , as well as a low efficiency roll-off. The current efficiency of the optimized OLED is maintained at more than 28.33 cd/A up to 10 000 cd m −2 . The detailed recombination mechanism of the prepared OLEDs is investigated by the transient electroluminescence method. It is concluded that there are no contributions from trapped charges and annihilations of triplet-triplet excitons to the detected electroluminescence

OVERVIEW OF ADVANCED PETROLEUM-BASED FUELS-DIESEL EMISSIONS CONTROL PROGRAM (APBF-DEC)

Energy Technology Data Exchange (ETDEWEB)

Sverdrup, George M.

2000-08-20

The Advanced Petroleum-Based Fuels-Diesel Emissions Control Program (APBF-DEC) began in February 2000 and is supported by government agencies and industry. The purpose of the APBF-DEC program is to identify and evaluate the optimal combinations of fuels, lubricants, diesel engines, and emission control systems to meet the projected emission standards for the 2000 to 2010 time period. APBF-DEC is an outgrowth of the earlier Diesel Emission Control-Sulfur Effects Program (DECSE), whose objective is to determine the impact of the sulfur levels in fuel on emission control systems that could lower the emissions of NOx and particulate matter (PM) from diesel powered vehicles in the 2002 to 2004 period. Results from the DECSE studies of two emission control technologies-diesel particle filter (DPF) and NOx adsorber-will be used in the APBF-DEC program. These data are expected to provide initial information on emission control technology options and the effects of fuel properties (including additives) on the performance of emission control systems.

A plasma process controlled emissions off-gas demonstration

International Nuclear Information System (INIS)

Battleson, D.; Kujawa, S.T.; Leatherman, G.

1995-01-01

Thermal technologies are currently identified as playing an important role in the treatment of many DOE waste streams, and emissions from these processes will be scrutinized by the public, regulators, and stakeholders. For some time, there has been a hesitancy by the public to accept thermal treatment of radioactive contaminated waste because of the emissions from these processes. While the technology for treatment of emissions from these processes is well established, it is not possible to provide the public complete assurance that the system will be in compliance with air quality regulations 100% of the operating time in relation to allowing noncompliant emissions to exit the system. Because of the possibility of noncompliant emissions and the public's concern over thermal treatment systems, it has been decided that the concept of a completely controlled emissions off-gas system should be developed and implemented on Department of Energy (DOE) thermal treatment systems. While the law of conservation of mass precludes a completely closed cycle system, it is possible to apply the complete control concept to emissions

Comparison between laser terahertz emission microscope and conventional methods for analysis of polycrystalline silicon solar cell

Directory of Open Access Journals (Sweden)

Hidetoshi Nakanishi

2015-11-01

Full Text Available A laser terahertz emission microscope (LTEM can be used for noncontact inspection to detect the waveforms of photoinduced terahertz emissions from material devices. In this study, we experimentally compared the performance of LTEM with conventional analysis methods, e.g., electroluminescence (EL, photoluminescence (PL, and laser beam induced current (LBIC, as an inspection method for solar cells. The results showed that LTEM was more sensitive to the characteristics of the depletion layer of the polycrystalline solar cell compared with EL, PL, and LBIC and that it could be used as a complementary tool to the conventional analysis methods for a solar cell.

Electroluminescence from GaN-polymer heterojunction

International Nuclear Information System (INIS)

Chitara, Basant; Lal, Nidhi; Krupanidhi, S.B.; Rao, C.N.R.

2011-01-01

Inorganic and organic semiconductor devices are generally viewed as distinct and separate technologies. Herein we report a hybrid inorganic-organic light-emitting device employing the use of an air stable polymer, Poly (9,9-dioctylfluorene-alt-benzothiadiazole) as a p-type layer to create a heterojunction, avoiding the use of p-type GaN, which is difficult to grow, being prone to the complex and expensive fabrication techniques that characterises it. I-V characteristics of the GaN-polymer heterojunction fabricated by us exhibits excellent rectification. The luminescence onset voltage is typically about 8-10 V. The device emits yellowish white electroluminescence with CIE coordinates (0.42, 0.44). - Highlights: → We use a polymer Poly (9,9-dioctylfluorene-alt-benzothiadiazole) as a p-type layer to create a heterojunction. → I-V characteristics of the device fabricated by us exhibits excellent rectification. → The p-type polymer also emits yellow light, which when combined in proper composition with GaN, give rise to white light. → Device can be readily fabricated by just spin coating the polymer over GaN reducing the cost of the device.

Electroluminescence of doped and undoped AlN/SiC-heterojunctions

Energy Technology Data Exchange (ETDEWEB)

Bruesewitz, Christoph; Vetter, Ulrich; Hofsaess, Hans [II. Physikalisches Institut, Georg-August-Universitaet Goettingen (Germany)

2010-07-01

AlN with its large and direct bandgap is a useful host for optoelectronic applications. Grown on 6H-SiC, a heterojunction is created, forming a diode. The light emitted by n-doped 6H-SiC via electroluminescence forms a broad band with a maximum at a wavelength of 475 nm. With the AlN layer on the surface, nitrogen atoms can diffuse into the 6H-SiC, creating new energy levels. Depending on the direction of the current and additional dopants in the AlN layer, the carrier concentration changes and new levels are available, resulting in different colours. It is shown that in this heterojunction blue, red and white colours are feasible.

Circadian control of isoprene emissions from oil palm (Elaeis guineensis).

Science.gov (United States)

Wilkinson, Michael J; Owen, Susan M; Possell, Malcolm; Hartwell, James; Gould, Peter; Hall, Anthony; Vickers, Claudia; Nicholas Hewitt, C

2006-09-01

The emission of isoprene from the biosphere to the atmosphere has a profound effect on the Earth's atmospheric system. Until now, it has been assumed that the primary short-term controls on isoprene emission are photosynthetically active radiation and temperature. Here we show that isoprene emissions from a tropical tree (oil palm, Elaeis guineensis) are under strong circadian control, and that the circadian clock is potentially able to gate light-induced isoprene emissions. These rhythms are robustly temperature compensated with isoprene emissions still under circadian control at 38 degrees C. This is well beyond the acknowledged temperature range of all previously described circadian phenomena in plants. Furthermore, rhythmic expression of LHY/CCA1, a genetic component of the central clock in Arabidopsis thaliana, is still maintained at these elevated temperatures in oil palm. Maintenance of the CCA1/LHY-TOC1 molecular oscillator at these temperatures in oil palm allows for the possibility that this system is involved in the control of isoprene emission rhythms. This study contradicts the accepted theory that isoprene emissions are primarily light-induced.

Emission and thermal performance upgrade through advanced control backfit

Energy Technology Data Exchange (ETDEWEB)

Banerjee, A.K. [Stone & Webster Engineering Corporation, Boston, MA (United States)

1994-12-31

Reducing emission and improving thermal performance of currently operating power plants is a high priority. A majority of these power plants are over 20 years old with old control systems. Upgrading the existing control systems with the latest technology has many benefits, the most cost beneficial are the reduction of emission and improving thermal performance. The payback period is usually less than two years. Virginia Power is installing Stone & Webster`s NO{sub x} Emissions Advisor and Advanced Steam Temperature Control systems on Possum Point Units 3 and 4 to achieve near term NO{sub x} reductions while maintaining high thermal performance. Testing has demonstrated NO{sub x} reductions of greater than 20 percent through the application of NO{sub x} Emissions Advisor on these units. The Advanced Steam Temperature Control system which has been operational at Virginia Power`s Mt. Storm Unit 1 has demonstrated a signification improvement in unit thermal performance and controllability. These control systems are being combined at Units 3 and 4 to reduce NO{sub x} emissions and achieve improved unit thermal performance and control response with the existing combustion hardware. Installation has been initiated and is expected to be completed by the spring of 1995. Possum Point Power Station Units 3 and 4 are pulverized coal, tangentially fired boilers producing 107 and 232 MW and have a distributed control system and a PC based performance monitoring system. The installation of the advanced control and automation system will utilize existing control equipment requiring the addition of several PCs and PLC.

City-specific vehicle emission control strategies to achieve stringent emission reduction targets in China's Yangtze River Delta region.

Science.gov (United States)

Zhang, Shaojun; Wu, Ye; Zhao, Bin; Wu, Xiaomeng; Shu, Jiawei; Hao, Jiming

2017-01-01

The Yangtze River Delta (YRD) region is one of the most prosperous and densely populated regions in China and is facing tremendous pressure to mitigate vehicle emissions and improve air quality. Our assessment has revealed that mitigating vehicle emissions of NOx would be more difficult than reducing the emissions of other major vehicular pollutants (e.g., CO, HC and PM 2.5 ) in the YRD region. Even in Shanghai, where the emission control implemented are more stringent than in Jiangsu and Zhejiang, we observed little to no reduction in NOx emissions from 2000 to 2010. Emission-reduction targets for HC, NOx and PM 2.5 are determined using a response surface modeling tool for better air quality. We design city-specific emission control strategies for three vehicle-populated cities in the YRD region: Shanghai and Nanjing and Wuxi in Jiangsu. Our results indicate that even if stringent emission control consisting of the Euro 6/VI standards, the limitation of vehicle population and usage, and the scrappage of older vehicles is applied, Nanjing and Wuxi will not be able to meet the NOx emissions target by 2020. Therefore, additional control measures are proposed for Nanjing and Wuxi to further mitigate NOx emissions from heavy-duty diesel vehicles. Copyright © 2016. Published by Elsevier B.V.

Synthesis and photophysical characteristics of 2,7-fluorenevinylene-based trimers and their electroluminescence.

Science.gov (United States)

Mikroyannidis, John A; Fenenko, Larysa; Adachi, Chihaya

2006-10-19

Three new 2,7-fluorenevinylene-based trimers were synthesized and characterized. The synthesis was carried out by the Heck coupling reaction of 9,9-dihexyl-2,7-divinylfluorene with 2-(4-bromophenyl)-5-phenyl-1,3,4-oxadiazole, N,N-diphenyl-4-bromoaniline, or 3-bromopyrene to afford the trimers OXD, TPA, and PYR, respectively. All the trimers were readily soluble in common organic solvents such as tetrahydrofuran, dichloromethane, chloroform, and toluene. Their glass transition temperatures ranged from 33 to 60 degrees C. The UV-vis spectra showed an absorption maximum at lambda(a,max) = 379-417 nm with optical band gap of Eg = 2.47-2.66 eV. In solution, they emitted strong blue-green photoluminescence (PL) with PL maximum at lambda(f,max) = 455-565 nm and fluorescence quantum yield of Phi(f) = 0.65-0.74. On the other hand, in their spin-coated films, the PL efficiencies significantly decreased due to the presence of concentration quenching. All samples showed nanosecond transient lifetime containing two components, suggesting excimer formation. The organic light-emitting diodes (OLEDs) with OXD and TPA showed green emission with electroluminescence (EL) quantum efficiencies of eta(EL) approximately 10(-2)%, while very weak EL efficiency of eta(EL) approximately 10(-5)% was observed with PYR. The highest occupied molecular orbital (HOMO) levels of the films were found to be 5.05-5.75 eV.

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Alq3; photoluminescence; electroluminescence; blue OLED; WOLED; DFT. Abstract. Synthesis, structure, optical absorption, emission and electroluminescence ... cd/m2 and maximum current efficiency of 0.16 cd/A. Another multilayer OLED ...

Spontaneous emission control in a tunable hybrid photonic system

NARCIS (Netherlands)

Frimmer, M.; Koenderink, A.F.

2013-01-01

We experimentally demonstrate control of the rate of spontaneous emission in a tunable hybrid photonic system that consists of two canonical building blocks for spontaneous emission control, an optical antenna and a mirror, each providing a modification of the local density of optical states (LDOS).

Impacts of Aging Emission Control Systems on In-Use Heavy-Duty Diesel Truck Emission Rates

Science.gov (United States)

Preble, C.; Cados, T.; Harley, R.; Kirchstetter, T.

2017-12-01

Heavy-duty diesel trucks are a major source of nitrogen oxides (NOx) and black carbon (BC) in urban environments, contributing to persistent ozone and particulate matter air quality problems. Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems have become standard equipment on new trucks. Particle filters can also be installed as a retrofit on older engines. Prior work has shown that exhaust filters and SCR systems effectively reduce BC and NOx emission rates by up to 90 and 80%, respectively (Preble et al., ES&T 2015). There is concern, however, that DPFs may promote the formation of ultrafine particles (UFP) and increase tailpipe emissions of nitrogen dioxide (NO2). Additionally, urea-based SCR systems for NOx control may form nitrous oxide (N2O), an important contributor to stratospheric ozone depletion. The effectiveness of these emission controls has been thoroughly evaluated in the laboratory, but the long-term durability of in-use systems and their impacts on co-emitted species have not been well characterized. To evaluate the in-use performance of DPF and SCR systems, pollutant emissions from thousands of diesel trucks were measured over several years at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Pollutants present in the exhaust plumes of individual trucks were measured at high time resolution (≥1 Hz) as trucks passed under a mobile lab stationed on an overpass. Fuel-based emission factors (g pollutant emitted per kg fuel burned) were calculated for individual trucks and linked via recorded license plates to vehicle attributes, including engine model year and installed emission control systems. Use of DPFs reduced the BC emission rate by up to 95% at both locations. SCR systems were more effective at reducing NOx emissions under the uphill, highway driving conditions at the Caldecott Tunnel. The emission rates of co-emitted species NO2, UFP, and N2O depended on driving

Quantification of Solar Cell Failure Signatures Based on Statistical Analysis of Electroluminescence Images

DEFF Research Database (Denmark)

Spataru, Sergiu; Parikh, Harsh; Hacke, Peter

2017-01-01

We demonstrate a method to quantify the extent of solar cell cracks, shunting, or damaged cell interconnects, present in crystalline silicon photovoltaic (PV) modules by statistical analysis of the electroluminescence (EL) intensity distributions of individual cells within the module. From the EL...... intensity distributions (ELID) of each cell, we calculated summary statistics such as standard deviation, median, skewness and kurtosis, and analyzed how they correlate with the magnitude of the solar cell degradation. We found that the dispersion of the ELID increases with the size and severity...

The effects of emission control strategies on light-absorbing carbon emissions from a modern heavy-duty diesel engine.

Science.gov (United States)

Robinson, Michael A; Olson, Michael R; Liu, Z Gerald; Schauer, James J

2015-06-01

Control of atmospheric black carbon (BC) and brown carbon (BrC) has been proposed as an important pathway to climate change mitigation, but sources of BC and BrC are still not well understood. In order to better identify the role of modern heavy-duty diesel engines on the production of BC and BrC, emissions from a heavy-duty diesel engine operating with different emission control strategies were examined using a source dilution sampling system. The effect of a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) on light-absorbing carbon (LAC) was evaluated at three steady-state engine operation modes: idle, 50% speed and load, and 100% speed and load. LAC was measured with four different engine configurations: engine out, DOC out, DPF out, and engine out with an altered combustion calibration. BC and BrC emission rates were measured with the Aethalometer (AE-31). EC and BC emission rates normalized to the mass of CO₂emitted increased with increasing engine speed and load. Emission rates normalized to brake-specific work did not exhibit similar trends with speed and load, but rather the highest emission rate was measured at idle. EC and OC emissions were reduced by 99% when the DOC and DPF architecture was applied. The application of a DPF was equally effective at removing 99% of the BC fraction of PM, proving to be an important control strategy for both LAC and PM. BC emissions were unexpectedly increased across the DOC, seemingly due to a change aerosol optical properties. Removal of exhaust gas recirculation (EGR) flow due to simulated EGR cooler failure caused a large increase in OC and BrC emission rates at idle, but had limited influence during high load operation. LAC emissions proved to be sensitive to the same control strategies effective at controlling the total mass of diesel PM. In the context of black carbon emissions, very small emission rates of brown carbon were measured over a range of control technologies and engine operating

Controlling spontaneous emission of light by photonic crystals

DEFF Research Database (Denmark)

Lodahl, Peter

2005-01-01

Photonic bandgap crystals were proposed almost two decades ago as a unique tool for controlling propagation and emission of light. Since then the research field of photonic crystals has exploded and many beautiful demonstrations of the use of photonic crystals and fibers for molding light...... propagation have appeared that hold great promises for integrated optics. These major achievements solidly demonstrate the ability to control propagation of light. In contrast, an experimental demonstration of the use of photonic crystals for timing the emission of light has so far lacked. In a recent...... publication in Nature, we have demonstrated experimentally that both the direction and time of spontaneous emission can be controlled, thereby confirming the original proposal by Eli Yablonovich that founded the field of photonic crystals. We believe that this work opens new opportunities for solid...

Control strategies for vehicular NOx emissions in Guangzhou, China

International Nuclear Information System (INIS)

Shao Min; Zhang Yuanhang; Raufer, Roger

2001-01-01

Guangzhou is a city in southern China that has experienced very rapid economic development in recent years. The city's air has very high concentrations of various pollutants, including sulphur dioxide (SO 2 , oxides of nitrogen (NOx), ozone (O 3 ) and particulate. This paper reviews the changes in air quality in the city over the past 15 years, and notes that a serious vehicular-related emissions problem has been superimposed on the traditional coal-burning problem evident in most Chinese cities. As NOx concentrations have increased, oxidants and photochemical smog now interact with the traditional SO 2 and particulate pollutants, leading to increased health risks and other environmental concerns. Any responsible NOx control strategy for the city must include vehicle emission control measures. This paper reviews control strategies designed to abate vehicle emissions to fulfill the city's air quality improvement target in 2010. A cost-effectiveness analysis suggests that, while NOx emission control is expensive, vehicular emission standards could achieve a relatively sizable emissions reduction at reasonable cost. To achieve the 2010 air quality target of NOx, advanced implementation of EURO3 standards is recommended, substituting for the EURO2 currently envisioned in the national regulations Related technical options, including fuel quality improvements and inspection/maintenance (I/M) upgrades (ASM or IM240) are assessed as well. (author)

Emissions inventories and options for control. Summary report

Energy Technology Data Exchange (ETDEWEB)

Swart, R.J.; Van Amstel, A.R.; Van den Born, G.J.; Kroeze, C.

1995-10-01

This report is the final summary report of the project `Social causes of the greenhouse effect, emissions inventories and options for control`. The objectives of the project, that started in 1990, were to support the development of a comprehensive Dutch climate policy and to identify gaps in the knowledge about sources of greenhouse gases. The four phases of the project are summarized. In the first phase, a first national inventory of greenhouse gas emissions was made, capturing carbon dioxide (CO{sub 2}), chlorofluorocarbons (CFCs), methane (CH{sub 4}), nitrous oxide (N{sub 2}O) and the ozone precursors carbon monoxide (CO), nitrogen oxides (NO{sub x} ) and volatile organic compounds (VOC). In the second phase, the acquired expertise was used to support the development of Guidelines for National Emissions Inventories by the joint OECD/IPCC programme through workshop organization and participation in the international planning group. In the third phase, a detailed analysis was performed of the sources of methane, its current and future emissions and the options for control. Finally, a similar analysis was performed for nitrous oxide. In these studies, it was found that policies not specifically aiming at mitigating climate change, would help to control the emissions of the non-CO{sub 2} greenhouse gases. While for methane, national emissions would even decrease because of measures in the livestock management and waste disposal sectors, for nitrous oxide the reductions in agricultural emissions would be outweighed by increases, especially in the transportation sector. The project shows that the application of more detailed information leads to differences with the Guidelines, both because of the limited number of source categories in the Guidelines and because of different, locally specific emissions factors. 4 figs., 2 tabs., 14 refs.

On-road vehicle emission control in Beijing: past, present, and future.

Science.gov (United States)

Wu, Ye; Wang, Renjie; Zhou, Yu; Lin, Bohong; Fu, Lixin; He, Kebin; Hao, Jiming

2011-01-01

Beijing, the capital of China, has experienced rapid motorization since 1990; a trend that is likely to continue. The growth in vehicles and the corresponding emissions create challenges to improving the urban air quality. In an effort to reduce the impact of vehicle emissions on urban air quality, Beijing has adopted a number of vehicle emission control strategies and policies since the mid 1990 s. These are classified into seven categories: (1) emission control on new vehicles; (2) emission control on in-use vehicles; (3) fuel quality improvements; (4) alternative-fuel and advanced vehicles; (5) economic policies; (6) public transport; and (7) temporal traffic control measures. Many have proven to be successful, such as the Euro emission standards, unleaded gasoline and low sulfur fuel, temporal traffic control measures during the Beijing Olympic Games, etc. Some, however, have been failures, such as the gasoline-to-LPG taxi retrofit program. Thanks to the emission standards for new vehicles as well as other controls, the fleet-average emission rates of CO, HC, NO(X), and PM(10) by each major vehicle category are decreasing over time. For example, gasoline cars decreased fleet-average emission factors by 12.5% for CO, 10.0% for HC, 5.8% for NO(X), and 13.0% for PM(10) annually since 1995, and such a trend is likely to continue. Total emissions for Beijing's vehicle fleet increased from 1995 to 1998. However, they show a clear and steady decrease between 1999 and 2009. In 2009, total emissions of CO, HC, NO(X), and PM(10) were 845,000 t, 121,000 t, 84,000 t, and 3700 t, respectively; with reductions of 47%, 49%, 47%, and 42%, relative to 1998. Beijing has been considered a pioneer in controlling vehicle emissions within China, similar to the role of California to the U.S. The continued rapid growth of vehicles, however, is challenging Beijing's policy-makers.

Electrochemical synthesis of MoS2 quantum dots embedded nanostructured porous silicon with enhanced electroluminescence property

Science.gov (United States)

Shrivastava, Megha; Kumari, Reeta; Parra, Mohammad Ramzan; Pandey, Padmini; Siddiqui, Hafsa; Haque, Fozia Z.

2017-11-01

In this report we present the successful enhancement in electroluminescence (EL) in nanostructured n-type porous silicon (PS) with an idea of embedding luminophorous Molybdenum disulfide (MoS2) quantum dots (QD's). Electrochemical anodization technique was used for the formation of PS surface and MoS2 QD's were prepared using the electrochemical route. Spin coating technique was employed for the proper incorporation of MoS2 QD's within the PS nanostructures. The crystallographic analysis was performed using X-ray diffraction (XRD), Raman and Fourier transform infrared (FT-IR) spectroscopy techniques. However, surface morphology was determined using Transmission electron microscopy (TEM) and Atomic force microscopy (AFM). The optical measurements were performed on photoluminescence (PL) spectrophotometer; additionally for electroluminescence (EL) study special arrangement of instrumental setup was made at laboratory level which provides novelty to this work. A diode prototype was made comprising Ag/MoS2:PS/Silicon/Ag for EL study. The MoS2:PS shows a remarkable concentration dependent enhancement in PL as well as in EL intensities, which paves a way to better utilize this strategy in optoelectronic device applications.

Analysis and control design of sustainable policies for greenhouse gas emissions

International Nuclear Information System (INIS)

Chu, Bing; Duncan, Stephen; Papachristodoulou, Antonis; Hepburn, Cameron

2013-01-01

Reducing greenhouse gas emissions is now an urgent priority. Systems control theory, and in particular feedback control, can be helpful in designing policies that achieve sustainable levels of emissions of CO 2 (and other greenhouse gases) while minimizing the impact on the economy, and at the same time explicitly addressing the high levels of uncertainty associated with predictions of future emissions. In this paper, we describe preliminary results for an approach where model predictive control (MPC) is applied to a model of the UK economy (UK 4see model) as a test bed to design sustainable policies for greenhouse gas emissions. Using feedback control, the policies are updated on the basis of the actual emissions, rather than on the predicted level of emissions. The basic structure and principle of the UK 4see model is described and its implementation in Simulink is presented. A linearized state space model is obtained and model predictive control is applied to design policies for CO 2 emissions. Simulation results are presented to demonstrate the effectiveness of the proposed method. The preliminary results obtained in this paper illustrate the strength of the proposed design approach and form the basis for future research on using systems control theory to design optimal sustainable policies

Quantification of solar cell failure signatures based on statistical analysis of electroluminescence images

DEFF Research Database (Denmark)

Spataru, Sergiu; Parikh, Harsh; Benatto, Gisele Alves dos Reis

2017-01-01

We propose a method to identify and quantify the extent of solar cell cracks, shunting, or damaged cell interconnects, present in crystalline silicon photovoltaic (PV) modules by statistical analysis of the electroluminescence (EL) intensity distributions of individual cells within the module. From...... the EL intensity distributions (ELID) of each cell, we calculated summary statistics such as standard deviation, median, skewness and kurtosis, and analyzed how they correlate with the type of the solar cell degradation. We found that the dispersion of the ELID increases with the size and severity...

Electroplex light emission based on BCP and a novel star-shaped hexafluorenylbenzene

Science.gov (United States)

Ma, Tao; Yu, Junsheng; Lou, Shuangling; Jiang, Yadong; Zhang, Qing

2009-05-01

Organic light emitting diode (OLEDs) are fabricated using a novel star-shaped hexafluorenylbenzene with a simple structure of indium-tin-oxide (ITO)/1,2,3,4,5,6-hexakis(9,9-diethyl-9H-fluoren-2-yl)benzene (HKEthFLYPh):N, N'-bis-(1-naphthyl)-N,N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine (NPB)/2,9-dimenthyl-4,7-diphenyl-1,10-phenanthroline (BCP)/tris(8-hydroxyquinoline) aluminum (Alq3)/Mg:Ag by spin coating method. The electroluminescent properties of the device are characterized. The results show that there is a new peak at 600 nm, which is no appearance in PL spectra. This new emission is proposed to be electroplex that occurred at the solid-state interface between HKEthFLYPh and BCP in addition to the exciton emission from NPB. The Commissions Internationale De L'Eclairage (CIE) coordinates of the device are (x=0.33, y=0.29) at 10 V, which obviously belongs to white light emission.

Electroluminescence and charge photogeneration in poly(9,9-dihexadecylfluorene-2,7-diyl) and its blends

Czech Academy of Sciences Publication Activity Database

Cimrová, Věra; Výprachtický, Drahomír

2004-01-01

Roč. 212, č. 1 (2004), s. 281-286 ISSN 1022-1360. [Electrical and Related Properties of Polymers and Other Organic Solids /9./. Prague, 14.07.2002-18.07.2002] R&D Projects: GA ČR GA203/01/0512; GA ČR GA102/98/0696 Institutional research plan: CEZ:AV0Z4050913 Keywords : electroluminescence * LEDs * poly(1,4-phenylene)s Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.691, year: 2004

Advanced Combustion and Emission Control Technical Team Roadmap

Energy Technology Data Exchange (ETDEWEB)

None

2013-06-01

The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

VOC from Vehicular Evaporation Emissions: Status and Control Strategy.

Science.gov (United States)

Liu, Huan; Man, Hanyang; Tschantz, Michael; Wu, Ye; He, Kebin; Hao, Jiming

2015-12-15

Vehicular evaporative emissions is an important source of volatile organic carbon (VOC), however, accurate estimation of emission amounts and scientific evaluation of control strategy for these emissions have been neglected outside of the United States. This study provides four kinds of basic emission factors: diurnal, hot soak, permeation, and refueling. Evaporative emissions from the Euro 4 vehicles (1.6 kg/year/car) are about four times those of U.S. vehicles (0.4 kg/year/car). Closing this emissions gap would have a larger impact than the progression from Euro 3 to Euro 6 tailpipe HC emission controls. Even in the first 24 h of parking, China's current reliance upon the European 24 h diurnal standard results in 508 g/vehicle/year emissions, higher than 32 g/vehicle/year from Tier 2 vehicles. The U.S. driving cycle matches Beijing real-world conditions much better on both typical trip length and average speed than current European driving cycles. At least two requirements should be added to the Chinese emissions standards: an onboard refueling vapor recovery to force the canister to be sized sufficiently large, and a 48-h evaporation test requirement to ensure that adequate purging occurs over a shorter drive sequence.

40 CFR 1060.104 - What running loss emission control requirements apply?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What running loss emission control... STATIONARY EQUIPMENT Emission Standards and Related Requirements § 1060.104 What running loss emission control requirements apply? (a) Engines and equipment must meet running loss requirements as follows: (1...

Emission Control Cost-Effectiveness of Alternative-Fuel Vehicles

OpenAIRE

Wang, Quanlu; Sperling, Daniel; Olmstead, Janis

1993-01-01

Although various legislation and regulations have been adopted to promote the use of alternative-fuel vehicles for curbing urban air pollution problems, there is a lack of systematic comparisons of emission control cost-effectiveness among various alternative-fuel vehicle types. In this paper, life-cycle emission reductions and life-cycle costs were estimated for passenger cars fueled with methanol, ethanol, liquified petroleum gas, compressed natural gas, and electricity. Vehicle emission es...

Online Traffic Signal Control for Reducing Vehicle Carbon Dioxide Emissions

Science.gov (United States)

Oda, Toshihiko; Otokita, Tohru; Niikura, Satoshi

In Japan, carbon dioxide (CO2) emissions caused by vehicles have been increasing year by year and it is well known that CO2 causes a serious global warming problem. For urban traffic control systems, there is a great demand for realization of signal control measures as soon as possible due to the urgency of the recent environmental situation. This paper describes a new traffic signal control for reducing vehicle CO2 emissions on an arterial road. First, we develop a model for estimating the emissions using the traffic delay and the number of stops a driver makes. Second, to find the optimal control parameters, we introduce a random search method with rapid convergence suitable for an online traffic control. We conduct experiments in Kawasaki to verify the effectiveness of our method. The experiments show that our approach decreases not only the emissions but also congestion and travel time significantly, compared to the method implemented in the real system.

Strategies for controlling pollution from vehicular emissions in Beijing

International Nuclear Information System (INIS)

Wang, Qidong; He, Kebin; Li, Tiejun; Fu, Lixin

2002-01-01

The paper describes the severe situation of vehicular emission in Beijing and discusses the following mitigation strategies: Improving fuel quality, controlling the exhaust from new vehicles, controlling the emissions from vehicles in use through e.g. Inspection Maintenance (I/M), renovating in-use vehicles and scrapping of old vehicles and road infrastructure and traffic policies. (Author)

Strategies for controlling pollution from vehicular emissions in Beijing

Energy Technology Data Exchange (ETDEWEB)

Wang, Qidong; He, Kebin; Li, Tiejun; Fu, Lixin

2002-07-01

The paper describes the severe situation of vehicular emission in Beijing and discusses the following mitigation strategies: Improving fuel quality, controlling the exhaust from new vehicles, controlling the emissions from vehicles in use through e.g. Inspection Maintenance (I/M), renovating in-use vehicles and scrapping of old vehicles and road infrastructure and traffic policies. (Author)

Quantum mechanical modeling the emission pattern and polarization of nanoscale light emitting diodes.

Science.gov (United States)

Wang, Rulin; Zhang, Yu; Bi, Fuzhen; Frauenheim, Thomas; Chen, GuanHua; Yam, ChiYung

2016-07-21

Understanding of the electroluminescence (EL) mechanism in optoelectronic devices is imperative for further optimization of their efficiency and effectiveness. Here, a quantum mechanical approach is formulated for modeling the EL processes in nanoscale light emitting diodes (LED). Based on non-equilibrium Green's function quantum transport equations, interactions with the electromagnetic vacuum environment are included to describe electrically driven light emission in the devices. The presented framework is illustrated by numerical simulations of a silicon nanowire LED device. EL spectra of the nanowire device under different bias voltages are obtained and, more importantly, the radiation pattern and polarization of optical emission can be determined using the current approach. This work is an important step forward towards atomistic quantum mechanical modeling of the electrically induced optical response in nanoscale systems.

N2O and NO2 Emissions from Heavy-Duty Diesel Trucks with Advanced Emission Controls

Science.gov (United States)

Preble, C.; Harley, R.; Kirchstetter, T.

2014-12-01

Diesel engines are the largest source of nitrogen oxides (NOx) emissions nationally, and also a major contributor to the black carbon (BC) fraction of fine particulate matter (PM). Recently, diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have become standard equipment on new heavy-duty diesel trucks. However, the deliberate catalytic oxidation of engine-out nitric oxide (NO) to nitrogen dioxide (NO2) in continuously regenerating DPFs leads to increased tailpipe emission of NO2. This is of potential concern due to the toxicity of NO2 and the resulting increases in atmospheric formation of other air pollutants such as ozone, nitric acid, and fine PM. While use of SCR reduces emissions of both NO and NO2, it may lead to increased emissions of nitrous oxide (N2O), a potent greenhouse gas. Here we report results from on-road measurements of heavy-duty diesel truck emissions conducted at the Port of Oakland and the Caldecott Tunnel in the San Francisco Bay Area. Emission factors (g pollutant per kg of diesel) were linked via recorded license plates to individual truck attributes, including engine model year and installed emission control equipment. Between 2009 and 2013, the fraction of DPF-equipped trucks at the Port of Oakland increased from 2 to 99%, and median engine age decreased from 11 to 6 years. Over the same period, fleet-average emission factors for black carbon and NOx decreased by 76 ± 22% and 53 ± 8%, respectively. However, direct emissions of NO2 increased, and consequently the NO2/NOx emission ratio increased from 0.03 ± 0.02 to 0.18 ± 0.03. Older trucks retrofitted with DPFs emitted approximately 3.5 times more NO2 than newer trucks equipped with both DPF and SCR. Preliminary data from summer 2014 measurements at the Caldecott Tunnel suggest that some older trucks have negative emission factors for N2O, and that for newer trucks, N2O emission factors have changed sign and

Acidification policy - control of acidifying emissions in Germany

International Nuclear Information System (INIS)

Schaerer, B.

1992-01-01

Since the mid-eighties total annual acidifying emissions have started to decline in West Germany. There was considerable impact on this positive trend in air pollution by the control of SO 2 and NO x emissions from large boilers, which were reduced by more than 80%. Corresponding control programmes have been established for other groups of sources as well as other pollutants and - with unification - for East Germany. The driving force behind this development was and still is first of all the legal principle of anticipatory action or precaution which means in practical terms 'emission minimization'. This cornerstone of German clean air legislation is the most powerful components of Germany's 'acidification policy', as it requires policy-makers to draw up new or review existing regulations for emission reduction based on requirements according to the state of the art and forces operators to apply the most modern ways and means of operation. This paper describes the system used in Germany to deal with air pollution, the emission minimization strategy, and the actions against acidifying emissions based thereon. In addition, an outlook on what might be necessary to cope with the challenges of a sustainable development concerning acidification is given. 1 ref., 1 fig., 2 tabs

Alternative control technology document for bakery oven emissions. Final report

Energy Technology Data Exchange (ETDEWEB)

Sanford, C.W.

1992-12-01

The document was produced in response to a request by the baking industry for Federal guidance to assist in providing a more uniform information base for State decision-making with regard to control of bakery oven emissions. The information in the document pertains to bakeries that produce yeast-leavened bread, rolls, buns, and similar products but not crackers, sweet goods, or baked foodstuffs that are not yeast leavened. Information on the baking processes, equipment, operating parameters, potential emissions from baking, and potential emission control options are presented. Catalytic and regenerative oxidation are identified as the most appropriate existing control technologies applicable to VOC emissions from bakery ovens. Cost analyses for catalytic and regenerative oxidation are included. A predictive formula for use in estimating oven emissions has been derived from source tests done in junction with the development of the document. Its use and applicability are described.

VOCs emission characteristics and priority control analysis based on VOCs emission inventories and ozone formation potentials in Zhoushan

Science.gov (United States)

Wang, Qiaoli; Li, Sujing; Dong, Minli; Li, Wei; Gao, Xiang; Ye, Rongmin; Zhang, Dongxiao

2018-06-01

Zhoushan is an island city with booming tourism and service industry, but also has many developed VOCs and/or NOX emission industries. It is necessary to carry out regional VOCs and O3 pollution control in Zhoushan as the only new area owns the provincial economic and social administration rights. Anthropogenic VOCs emission inventories were built based on emission factor method and main emission sources were identified according to the emission inventories. Then, localized VOCs source profiles were built based on in-site sampling and referring to other studies. Furthermore, ozone formation potentials (OFPs) profiles were built through VOCs source profiles and maximum incremental reactivity (MIR) theory. At last, the priority control analysis results showed that industrial processes, especially surface coating, are the key of VOCs and O3 control. Alkanes were the most emitted group, accounting for 58.67%, while aromatics contributed the most to ozone production accounting for 69.97% in total OFPs. n-butane, m/p-xylene, i-pentane, n-decane, toluene, propane, n-undecane, o-xylene, methyl cyclohexane and ethyl benzene were the top 10 VOC species that should be preferentially controlled for VOCs emission control. However, m/p-xylene, o-xylene, ethylene, n-butane, toluene, propene, 1,2,4-trimethyl benzene, 1,3,5-trimethyl benzene, ethyl benzene and 1,2,3-trimethyl benzene were the top 10 VOC species that required preferential control for O3 pollution control.

Environmental emissions control programs at Lambton TGS [Thermal Generating Station

International Nuclear Information System (INIS)

Kalvins, A.K.

1992-01-01

Ontario Hydro's air emissions control programs at Lambton thermal generating station, both committed and planned, are reviewed, and their potential impacts on emissions, effluents and wastes are discussed. Control technologies examined include flue gas conditioning, wet limestone scrubbing, combustion process modifications, urea injection, and selective catalytic reduction. The implementation of these technologies has the potential to create new solid and liquid waste disposal problems, the full extent of which is often not realized at the process selection stage. For example, selective noncatalytic reduction using urea injection can lead to increased CO emissions, escape of unreacted ammonia from the stack at levels of 5-50 ppM, increase in N 2 O emissions, contamination of fly ash, gypsum and waste water with ammonia, and an increase in CO 2 emissions of less than 0.4% due to increased power consumption. Optimum performance of the air emissions control systems, with minimum negative impact on the environment, requires consideration of the impact of these systems on all waste streams. 11 refs., 3 figs., 1 tab

40 CFR 75.34 - Units with add-on emission controls.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Units with add-on emission controls... add-on emission controls. (a) The owner or operator of an affected unit equipped with add-on SO2 and... assurance/quality control program for the unit, required by section 1 in appendix B of this part. To provide...

Efficient near-infrared emission of π-extended cyclometalated iridium complexes based on pyrene in solution-processed polymer light-emitting diode

Science.gov (United States)

Liu, Yu; Hao, Zhaoran; Meng, Fanyuan; Wang, Pu; Yang, Liang; Wang, Yafei; Pei, Yong; Su, Shijian

2018-05-01

A novel iridium complex grafting hole-transporting triphenylamine (TPA) unit onto cyclometalated ligand, namely t-BuPyrPyTPA)2Ir(acac), was successfully synthesized and characterized. The photophysical, electrochemical and DFT/TD-DFT calculation, as well as electroluminescence properties of this iridium complex were fully investigated. Meanwhile, the PLEDs employing (t-BuPyrPyTPA)2Ir(acac) as dopant presented stable NIR emission peaked at 697 nm and a shoulder at 764 nm with a highest external quantum efficiency (EQE) of 0.56% at 4 wt% dopant concentration. These results demonstrate that expanding the conjugation length of the ligand is an effective way to achieve NIR emission.

Use of gas mixture electroluminescence for optical data readout from wire chambers

International Nuclear Information System (INIS)

Polyakov, V.A.; Rykalin, V.I.; Tskhadadze, Eh.G.

1988-01-01

The radiation spectra, the values of electroluminescence yield and coefficients of gas amplification of Ar and Ne mixture with inorganic and organic additions in a wire chamber operating under proportional and self-quenching streamer conditions are measured. Maximum light yield: 2x10 7 photons for Ar+acetone+white spirit gas mixture in a proportional regime and 1.1x10 7 photons for Ar+CO 2 + ethyl alcohol+ white spirit in self-quenching streamer regime is obtained. Three methods of optical data readout from the wire chambers are tested. The best results are obtained when spectrum shifting bands and fibers are placed behind the chamber cathode planes

Electroluminescence Analysis by Tilt Polish Technique of InP-Based Semiconductor Lasers

Science.gov (United States)

Ichikawa, Hiroyuki; Sasaki, Kouichi; Hamada, Kotaro; Yamaguchi, Akira

2010-03-01

We developed an effective electroluminescence (EL) analysis method to specify the degraded region of InP-based semiconductor lasers. The EL analysis method is one of the most important methods for failure analysis. However, EL observation was difficult because opaque electrodes surround an active layer. A portion of each electrode had to be left intact for wiring to inject the current. Thus, we developed a partial polish technique for the bottom electrode. Tilt polish equipment with a rotating table was introduced; a flat polished surface and a sufficiently wide remaining portion of the bottom electrode were obtained. As a result, clear EL from the back surface of the laser was observed.

Mercury emission, control and measurement from coal combustion

Energy Technology Data Exchange (ETDEWEB)

Pan, Wei-Ping [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering; Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Cao, Yan [Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Zhang, Kai [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering

2013-07-01

Coal-fired electric power generation accounts for 65% of U.S. emissions of sulfur dioxide (SO2), 22% of nitrogen oxides (NOx), and 37% of mercury (Hg). The proposed Clear Air Interstate Rule (CAIR) and Clean Air Mercury Rule (CAMR) will attempt to regulate these emissions using a cap-and-trade program to replace a number of existing regulatory requirements that will impact this industry over the next decade. Mercury emissions remain the largest source that has not yet been efficiently controlled, in part because this is one of the most expensive to control. Mercury is a toxic, persistent pollutant that accumulates in the food chain. During the coal combustion process, when both sampling and accurate measurements are challenging, we know that mercury is present in three species: elemental, oxidized and particulate. There are three basic types of mercury measurement methods: Ontario Hydro Method, mercury continuous emission monitoring systems (CEMS) and sorbent-based monitoring. Particulate mercury is best captured by electrostatic precipitators (ESP). Oxidized mercury is best captured in wet scrubbers. Elemental mercury is the most difficult to capture, but selective catalytic reduction units (SCRs) are able to convert elemental mercury to oxidized mercury allowing it to be captured by wet flue gas desulfurization (FGD). This works well for eastern coals with high chlorine contents, but this does not work well on the Wyoming Powder River Basin (PRB) coals. However, no good explanation for its mechanism, correlations of chlorine content in coal with SCR performance, and impacts of higher chlorine content in coal on FGD re-emission are available. The combination of SCR and FGD affords more than an 80% reduction in mercury emissions in the case of high chlorine content coals. The mercury emission results from different coal ranks, boilers, and the air pollution control device (APCD) in power plant will be discussed. Based on this UAEPA new regulation, most power plants

Control strategies for nitrous oxide emissions reduction on wastewater treatment plants operation.

Science.gov (United States)

Santín, I; Barbu, M; Pedret, C; Vilanova, R

2017-11-15

The present paper focused on reducing greenhouse gases emissions in wastewater treatment plants operation by application of suitable control strategies. Specifically, the objective is to reduce nitrous oxide emissions during the nitrification process. Incomplete nitrification in the aerobic tanks can lead to an accumulation of nitrite that triggers the nitrous oxide emissions. In order to avoid the peaks of nitrous oxide emissions, this paper proposes a cascade control configuration by manipulating the dissolved oxygen set-points in the aerobic tanks. This control strategy is combined with ammonia cascade control already applied in the literature. This is performed with the objective to take also into account effluent pollutants and operational costs. In addition, other greenhouse gases emissions sources are also evaluated. Results have been obtained by simulation, using a modified version of Benchmark Simulation Model no. 2, which takes into account greenhouse gases emissions. This is called Benchmark Simulation Model no. 2 Gas. The results show that the proposed control strategies are able to reduce by 29.86% of nitrous oxide emissions compared to the default control strategy, while maintaining a satisfactory trade-off between water quality and costs. Copyright © 2017 Elsevier Ltd. All rights reserved.

An Equivalent Emission Minimization Strategy for Causal Optimal Control of Diesel Engines

Directory of Open Access Journals (Sweden)

Stephan Zentner

2014-02-01

Full Text Available One of the main challenges during the development of operating strategies for modern diesel engines is the reduction of the CO2 emissions, while complying with ever more stringent limits for the pollutant emissions. The inherent trade-off between the emissions of CO2 and pollutants renders a simultaneous reduction difficult. Therefore, an optimal operating strategy is sought that yields minimal CO2 emissions, while holding the cumulative pollutant emissions at the allowed level. Such an operating strategy can be obtained offline by solving a constrained optimal control problem. However, the final-value constraint on the cumulated pollutant emissions prevents this approach from being adopted for causal control. This paper proposes a framework for causal optimal control of diesel engines. The optimization problem can be solved online when the constrained minimization of the CO2 emissions is reformulated as an unconstrained minimization of the CO2 emissions and the weighted pollutant emissions (i.e., equivalent emissions. However, the weighting factors are not known a priori. A method for the online calculation of these weighting factors is proposed. It is based on the Hamilton–Jacobi–Bellman (HJB equation and a physically motivated approximation of the optimal cost-to-go. A case study shows that the causal control strategy defined by the online calculation of the equivalence factor and the minimization of the equivalent emissions is only slightly inferior to the non-causal offline optimization, while being applicable to online control.

Electroluminescence of a-Si/c-Si heterojunction solar cells after high energy irradiation

Energy Technology Data Exchange (ETDEWEB)

Ferrara, Manuela

2009-11-24

The crystalline silicon as absorber material will certainly continue to dominate the market for space applications of solar cells. In the contribution under consideration the applicability of a-Si:H/c-Si heterojunction solar cells in space has been tested by the investigation of the cell modification by high energy protons and comparing the results to the degradation of homojunction crystalline silicon reference cells. The investigated solar cells have been irradiated with protons of different energies and doses. For all investigated solar cells the maximum damage happens for an energy of about 1.7 MeV and is mainly due to the decrease of the effective minority carrier diffusion length in the crystalline silicon absorber. Simulations carried out by AFORS-HET, a heterojunction simulation program, also confirmed this result. The main degradation mechanism for all types of devices is the monotonically decreasing charge carrier diffusion length in the p-type monocrystalline silicon absorber layer. For the heterojunction solar cell an enhancement of the photocurrent in the blue wavelength region has been observed but only in the case of heterojunction solar cell with intrinsic a-Si:H buffer layer. Additionally to the traditional characterization techniques the electroluminescence technique used for monitoring the modifications of the heteroluminescence technique used for monitoring the modifications of the heterointerface between amorphous silicon and crystalline silicon in solar cells after proton irradiation. A direct relation between minority carrier diffusion length and electroluminescence quantum efficiency has been observed but also details of the interface modification could be monitored by this technique.

Control of mobility in molecular organic semiconductors by dendrimer generation

Science.gov (United States)

Lupton, J. M.; Samuel, I. D.; Beavington, R.; Frampton, M. J.; Burn, P. L.; Bässler, H.

2001-04-01

Conjugated dendrimers are of interest as novel materials for light-emitting diodes. They consist of a luminescent chromophore at the core with highly branched conjugated dendron sidegroups. In these materials, light emission occurs from the core and is independent of generation. The dendron branching controls the separation between the chromophores. We present here a family of conjugated dendrimers and investigate the effect of dendron branching on light emission and charge transport. We apply a number of transport measurement techniques to thin films of a conjugated dendrimer in a light-emitting diode configuration to determine the effect of chromophore spacing on charge transport. We find that the mobility is reduced by two orders of magnitude as the size of the molecule doubles with increased branching or dendrimer generation. The degree of branching allows a unique control of mobility by molecular structure. An increase in chromophore separation also results in a reduction of intermolecular interactions, which reduces the red emission tail in film photoluminescence. We find that the steady-state charge transport is well described by a simple device model incorporating the effect of generation, and use the materials to shed light on the interpretation of transient electroluminescence data. We demonstrate the significance of the ability to tune the mobility in bilayer devices, where a more balanced charge transport can be achieved.

Coherent control of atto-second emission from aligned molecules

Energy Technology Data Exchange (ETDEWEB)

Boutu, W; Haessler, S; Merdji, H; Breger, P; Monchicourt, P; Carre, B; Salieres, P [CEA Saclay, DSM, Serv Photons Atomes Mol, F-91191 Gif Sur Yvette, (France); Waters, G [Univ Reading, JJ Thomson Phys Lab, Reading RG6 6AF, Berks, (United Kingdom); Stankiewicz, M [Jagiellonian Univ, Inst Phys, PL-30059 Krakow, (Poland); Frasinski, L J [Univ London Imperial Coll Sci Technol and Med, Blackett Lab, London SW7 2BW, (United Kingdom); Taieb, R; Caillat, J; Maquet, A [Univ Paris 06, UMR 7614, Lab Chim Phys Matiere Rayonnement, F-75231 Paris 05, (France); Taieb, R; Caillat, J; Maquet, A [LCPMR, UMR 7614, CNRS, F-75005 Paris, (France)

2008-07-01

Controlling atto-second electron wave packets and soft X-ray pulses represents a formidable challenge of general implication to many areas of science. A strong laser field interacting with atoms or molecules drives ultrafast intra-atomic/molecular electron wave packets on a sub femtosecond timescale, resulting in the emission of atto-second bursts of extreme-ultraviolet light. Controlling the intra-atomic/molecular electron dynamics enables steering of the atto-second emission. Here, we carry out a coherent control in linear molecules, where the interaction of the laser-driven electron wave packet with the core leads to quantum interferences. We demonstrate that these interferences can be finely controlled by turning the molecular axis relative to the laser polarization, that is, changing the electron re-collision angle. The wave-packet coulombic distortion modifies the spectral phase jump measured in the extreme-ultraviolet emission. Our atto-second control of the interference results in atto-second pulse shaping, useful for future applications in ultrafast coherent control of atomic and molecular processes. (authors)

PM, NOx and butane emissions from on-road vehicle fleets in Hong Kong and their implications on emission control policy

Science.gov (United States)

Ning, Zhi; Wubulihairen, Maimaitireyimu; Yang, Fenhuan

2012-12-01

Vehicular emissions are the major sources of air pollution in urban areas. For metropolitan cities with large population working and living in environments with direct traffic impact, emission control is of great significance to protect public health. Implementation of more stringent emission standards, retrofitting fleet with emission control devices and switching to clearer fuel has been commonly practiced in different cities including Hong Kong. The present study employed a new plume chasing method for effective and quick evaluation of on-road fleet emission factors of particulate matter (PM), nitrogen oxides (NOx), and butane from heavy duty diesel trucks, diesel buses and liquefied petroleum gas (LPG) vehicles. The results showed distinct profiles of the emissions from different fleets with excessive butane emissions from LPG fleet and contrasting PM and NOx emissions from diesel trucks and buses fleets. A cross comparison was also made with emission data from other cities and from historic local studies. The implications of the observed difference on the effectiveness of emission control measures and policy are discussed with recommendations of direction for future research and policy making.

Control of fine particulate (PM2.5) emissions from restaurant operations.

Science.gov (United States)

Whynot, J; Quinn, G; Perryman, P; Votlucka, P

1999-09-01

This paper describes efforts to reduce particulate matter (PM) emissions from restaurant operations, including application of an existing control method to a new equipment type. Commercial charbroiling in the South Coast Air Basin results in emissions of approximately 10 tons/day of fine particulate matter (PM2.5) and 1.3 tons/day of volatile organic compounds (VOCs). Over a seven-year period, the South Coast Air Quality Management District worked with industry to develop test methods for measuring emissions from various cooking operations, evaluate control technologies, and develop a rule to reduce these emissions. Of the two basic types of charbroilers--chain-driven and underfired--underfired produce four times the emissions when equivalent amounts of product are cooked. Cost-effective control technology is currently available only for chain-driven charbroilers. The application of flameless catalytic oxidizers to chain-driven charbroilers was found to effectively reduce emissions by at least 83% and is cost-effective. The catalysts have been used worldwide at restaurants for several years. Research efforts are underway to identify control options for underfired charbroilers. Implementation of Rule 1138, Control of Emissions from Restaurant Operations, adopted November 14, 1997, will result in reductions of 0.5 tons/day of PM2.5 and 0.2 tons/day of VOCs. Future rules will result in reductions from underfired charbroilers and possibly other restaurant equipment when cost-effective solutions are available.

Influence of heterojunction interface on exciplex emission from organic light-emitting diodes under electric fields

Energy Technology Data Exchange (ETDEWEB)

Yang, Shengyi; Zhang, Xiulong; Lou, Zhidong; Hou, Yanbing [Beijing Jiaotong University, Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing (China)

2008-03-15

In this paper, electroluminescence from organic light-emitting diodes based on 2-(4'-biphenyl)-5-(4{sup ''}-tert-butylphenyl)-1,3,4-oxadiazole (PBD) and N,N'-diphenyl-N,N'-bis(3-methylphenyl)-(1,1'-biphenyl)-4,4'-diamine (TPD) is reported. Based on the exciplex emission from the TPD/PBD interface under high electric fields, the influence of the TPD/PBD interface on exciplex emission was investigated by increasing the number of TPD/PBD interfaces while keeping both the total thickness of the TPD layer and the PBD layer constant in the multiple quantum-wells (MQW) device ITO/TPD/[PBD/TPD]{sub n}/PBD/Al (n is the well number that was varied from 0 to 3). Our experimental data shows that exciplex emission can be enhanced by suitably increasing the well number of this kind of MQW-like device. (orig.)

PANI Branches onto Donor-Acceptor Copolymers: Synthesis, Characterization and Electroluminescent Properties of New 2D-Materials

Directory of Open Access Journals (Sweden)

Ignacio A. Jessop

2018-05-01

Full Text Available A new series of two-dimensional statistical conjugated polymers based on aniline and 9,9-dihexylfluorene as donor units and benzo- or naphtho-quinoxaline/thiadiazole derivatives as acceptor moieties, possessing PANI segments as side chains, were designed and synthesized. To investigate the effects of the perpendicular PANI branches on the properties of the main chain, the optical, electrochemical, morphological and electroluminescence properties were studied. The 2D materials tend to possess lower molecular weights and to absorb and to emit light red-shifted compared to the trunk 1D-polymers, in the yellow-red region of the visible spectrum. The 1D- and 2D-conjugated polymers present optical band gaps ranging from 2.15–2.55 eV, HOMO energy levels between −5.37 and −5.60 eV and LUMO energy levels between −3.02 and −3.29 eV. OLED devices based on these copolymers were fabricated. Although the performances were far from optimal due to the high turn-on voltages for which electroluminescence phenomena occur, a maximum luminescence of 55,100 cd/m2 together with a current density of 65 mA/cm2 at 18.5 V were recorded for a 2D-copolymer, PAFC6TBQ-PANI.

Phosphorescent Molecularly Doped Light-Emitting Diodes with Blended Polymer Host and Wide Emission Spectra

Directory of Open Access Journals (Sweden)

Jun Wang

2013-01-01

Full Text Available Stable green light emission and high efficiency organic devices with three polymer layers were fabricated using bis[2-(4′-tert-butylphenyl-1-phenyl-1H-benzoimidazole-N,C2′] iridium(III (acetylacetonate doped in blended host materials. The 1 wt% doping concentration showed maximum luminance of 7841 cd/cm2 at 25.6 V and maximum current efficiency of 9.95 cd/A at 17.2 V. The electroluminescence spectra of devices indicated two main peaks at 522 nm and 554 nm coming from phosphor dye and a full width at half maximum (FWHM of 116 nm. The characteristics of using blended host, doping iridium complex, emission spectrum, and power efficiency of organic devices were investigated.

Spectroscopic investigation of the interfaces in new poly(9,9-dihexyl–9H-fluorene-2,7- diyl based electroluminescent devices

Directory of Open Access Journals (Sweden)

C. Donitsi

2014-01-01

Full Text Available The highest occupied and lowest unoccupied states of the new electroluminescent material poly(9,9-dihexyl–9H- fluorene-2,7-diyl (PPV-D and polyvinylcarbazole (PVK are investigated using ultraviolet photoelectron and inverse photoemission spectroscopies. Hole injection barriers are determined for interfaces between indium-tin oxide covered substrates with work function ranging from 4.4 to 4.7 eV and these two polymers. Vacuum level alignment with flat bands away from the interface is found when the interface hole barrier is 0.6 eV or larger. Band bending away from the Fermi level occurs when the hole barrier is smaller than 0.6 eV. This is due to the accumulation charges at the interface with the polymer when the injection barrier is small. The resulting field bends the polymer levels to limit charge incoming in the bulk of the film. The efficiency of the electroluminescent structures is strongly influenced by the different energy levels alignment at the layer interfaces.

White-electroluminescent device with horizontally patterned blue/yellow phosphor-layer structure

International Nuclear Information System (INIS)

Won Park, Boo; Sik Choi, Nam; Won Park, Kwang; Mo Son, So; Kim, Jong Su; Kyun Shon, Pong

2007-01-01

White-electroluminescent (EL) devices with stripe-patterned and square-patterned phosphor-layer structures are fabricated through a screen printing method: electrode/BaTiO 3 insulator layer/patterned blue ZnS:Cu, Cl and yellow ZnS:Cu, Mn phosphor layer/ITO PET substrate. The luminous intensities of EL devices with stripe-patterned and square-patterned phosphor-layer structures are 33% and 23% higher than a conventional device with the phosphor-layer structure without any patterns using the phosphor blend. It can be explained in terms of the absorption of the emitted blue light of blue phosphor layer by the yellow-emitting phosphor layer. The EL device of our patterned phosphor-layer structure gives the possibility to enhance the luminance

Origin of yellow emission in white OLED with single emitting material

Energy Technology Data Exchange (ETDEWEB)

Akimoto, Ikuko; Tsuzuki, Sayaka; Uzawa, Hidetoshi; Hinatsu, Masako; Nishide, Yosuke; Osuga, Hideji; Sakamoto, Hidefumi [Faculty of Systems Engineering, Wakayama University, Sakaedani 930, Wakayama 640-8510 (Japan)

2011-01-15

The photo-luminescence (PL) and electro-luminescence (EL) of a novel organic material, benzodithiophene/triphenylamine copolymer (P-PBTx, n=5-6) were investigated. The PL exhibited wide blue emission at room temperature, which is attributed to fluorescence from a chromophore, benzodithiophene moiety, from results of spectral analysis and decay profile. The EL, however, exhibited white emission consisting of wide blue (B) and yellow (Y) bands, although it was prepared with P-PBTx as a single emitting material. The Y-band was slightly observed at 7 K and found to possess long lived component of 19 ms lifetime. The origin of the Y-band efficiently stimulated by carrier injection is supposed to be a charge-transfer state between benzodithiophene and triphenylamine moieties. The long lived component could be explained by lowered transition probability caused by charge separation. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Effect of localization states on the electroluminescence spectral width of blue–green light emitting InGaN/GaN multiple quantum wells

Energy Technology Data Exchange (ETDEWEB)

Liu, Wei [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083, China and School of Electronic and Electrical Engineering, Chongqing University of Arts and Sciences, Chongqing 402160 (China); Zhao, De Gang, E-mail: dgzhao@red.semi.ac.cn; Jiang, De Sheng; Chen, Ping; Liu, Zong Shun; Zhu, Jian Jun; Li, Xiang; Shi, Ming; Zhao, Dan Mei [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Liu, Jian Ping; Zhang, Shu Ming; Wang, Hui; Yang, Hui [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, Suzhou 215125 (China)

2015-11-15

The electroluminescence (EL) spectra of blue–green light emitting InGaN/GaN multiple quantum well (MQW) structures grown via metal-organic chemical vapor deposition are investigated. With increasing In content in InGaN well layers, the peak energy redshifts, the emission intensity reduces and the inhomogeneous broadening of the luminescence band increases. In addition, it is found that the EL spectra shrink with increasing injection current at low excitation condition, which may be ascribed to both Coulomb screening of polarization field and carrier transferring from shallower localization states to the deeper ones, while at high currents the state-filling effect in all localization states may become significant and lead to a broadening of EL spectra. However, surprisingly, for the MQW sample with much higher In content, the EL spectral bandwidth can be almost unchanged with increasing current at the high current range, since a large number of carriers may be captured by the nonradiative recombination centers distributed outside the localized potential traps and the state-filling effect in the localization states is suppressed.

Effect of localization states on the electroluminescence spectral width of blue–green light emitting InGaN/GaN multiple quantum wells

International Nuclear Information System (INIS)

Liu, Wei; Zhao, De Gang; Jiang, De Sheng; Chen, Ping; Liu, Zong Shun; Zhu, Jian Jun; Li, Xiang; Shi, Ming; Zhao, Dan Mei; Liu, Jian Ping; Zhang, Shu Ming; Wang, Hui; Yang, Hui

2015-01-01

The electroluminescence (EL) spectra of blue–green light emitting InGaN/GaN multiple quantum well (MQW) structures grown via metal-organic chemical vapor deposition are investigated. With increasing In content in InGaN well layers, the peak energy redshifts, the emission intensity reduces and the inhomogeneous broadening of the luminescence band increases. In addition, it is found that the EL spectra shrink with increasing injection current at low excitation condition, which may be ascribed to both Coulomb screening of polarization field and carrier transferring from shallower localization states to the deeper ones, while at high currents the state-filling effect in all localization states may become significant and lead to a broadening of EL spectra. However, surprisingly, for the MQW sample with much higher In content, the EL spectral bandwidth can be almost unchanged with increasing current at the high current range, since a large number of carriers may be captured by the nonradiative recombination centers distributed outside the localized potential traps and the state-filling effect in the localization states is suppressed

Kinetics of transient electroluminescence in organic light emitting diodes

Science.gov (United States)

Shukla, Manju; Kumar, Pankaj; Chand, Suresh; Brahme, Nameeta; Kher, R. S.; Khokhar, M. S. K.

2008-08-01

Mathematical simulation on the rise and decay kinetics of transient electroluminescence (EL) in organic light emitting diodes (OLEDs) is presented. The transient EL is studied with respect to a step voltage pulse. While rising, for lower values of time, the EL intensity shows a quadratic dependence on (t - tdel), where tdel is the time delay observed in the onset of EL, and finally attains saturation at a sufficiently large time. When the applied voltage is switched off, the initial EL decay shows an exponential dependence on (t - tdec), where tdec is the time when the voltage is switched off. The simulated results are compared with the transient EL performance of a bilayer OLED based on small molecular bis(2-methyl 8-hydroxyquinoline)(triphenyl siloxy) aluminium (SAlq). Transient EL studies have been carried out at different voltage pulse amplitudes. The simulated results show good agreement with experimental data. Using these simulated results the lifetime of the excitons in SAlq has also been calculated.

Kinetics of transient electroluminescence in organic light emitting diodes

International Nuclear Information System (INIS)

Shukla, Manju; Brahme, Nameeta; Kumar, Pankaj; Chand, Suresh; Kher, R S; Khokhar, M S K

2008-01-01

Mathematical simulation on the rise and decay kinetics of transient electroluminescence (EL) in organic light emitting diodes (OLEDs) is presented. The transient EL is studied with respect to a step voltage pulse. While rising, for lower values of time, the EL intensity shows a quadratic dependence on (t - t del ), where t del is the time delay observed in the onset of EL, and finally attains saturation at a sufficiently large time. When the applied voltage is switched off, the initial EL decay shows an exponential dependence on (t - t dec ), where t dec is the time when the voltage is switched off. The simulated results are compared with the transient EL performance of a bilayer OLED based on small molecular bis(2-methyl 8-hydroxyquinoline)(triphenyl siloxy) aluminium (SAlq). Transient EL studies have been carried out at different voltage pulse amplitudes. The simulated results show good agreement with experimental data. Using these simulated results the lifetime of the excitons in SAlq has also been calculated

Wavelength-tuned light emission via modifying the band edge symmetry: Doped SnO2 as an example

KAUST Repository

Zhou, Hang

2014-03-27

We report the observation of ultraviolet photoluminescence and electroluminescence in indium-doped SnO2 thin films with modified "forbidden" bandgap. With increasing indium concentration in SnO 2, dominant visible light emission evolves into the ultraviolet regime in photoluminescence. Hybrid functional first-principles calculations demonstrate that the complex of indium dopant and oxygen vacancy breaks "forbidden" band gap to form allowed transition states. Furthermore, undoped and 10% indium-doped SnO2 layers are synthesized on p-type GaN substrates to obtain SnO2-based heterojunction light-emitting diodes. A dominant visible emission band is observed in the undoped SnO 2-based heterojunction, whereas strong near-ultraviolet emission peak at 398 nm is observed in the indium-doped SnO2-based heterojunction. Our results demonstrate an unprecedented doping-based approach toward tailoring the symmetry of band edge states and recovering ultraviolet light emission in wide-bandgap oxides. © 2014 American Chemical Society.

Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

Energy Technology Data Exchange (ETDEWEB)

Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Ryu, Dae Hyun [Department of Information Technology, Hansei University, Gunpo (Korea, Republic of); Wood, Richard [Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada); Moon, C.-B. [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Kim, Woo Young, E-mail: wykim@hoseo.edu [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada)

2013-11-15

The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE{sub x,y}) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE{sub x,y} coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source.

Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

International Nuclear Information System (INIS)

Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn; Ryu, Dae Hyun; Wood, Richard; Moon, C.-B.; Kim, Woo Young

2013-01-01

The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE x,y ) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE x,y coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source

Process control with optical emission spectroscopy in triode ion plating

International Nuclear Information System (INIS)

Salmenoja, K.; Korhonen, A.S.; Sulonen, M.S.

1985-01-01

Physical vapor deposition (PVD) techniques used to prepare, e.g., hard TiN, HfN, or ZrN coatings include a great variety of processes ranging from reactive evaporation to sputtering and ion plating. In ion plating one effective way to enhance ionization is to use a negatively biased hot filament. The use of an electron emitting filament brings an extra variable to be taken into account in developing the process control. In addition, proper control of the evaporation source is critical in ensuring reproducible results. With optical emission spectroscopy (OES) it should be possible to control the coating process more accurately. The stoichiometry and the composition of the growing coating may then be ensured effectively in subsequent runs. In this work the application of optical emission spectroscopy for process control in triode ion plating is discussed. The composition of the growing coating is determined experimentally using the relative intensities of specific emission lines. Changes in the evaporation rate and the gas flow can be seen directly from emission line intensities. Even the so-called poisoning of the evaporation source with reactive gas can be detected. Several experimental runs were carried out and afterwards the concentration profiles of the deposited coatings were checked with the nuclear resonance broadening (NRB) method. The results show the usefulness of emission spectroscopy in discharge control

40 CFR 1060.102 - What permeation emission control requirements apply for fuel lines?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What permeation emission control... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EVAPORATIVE EMISSIONS FROM NEW AND IN-USE NONROAD AND STATIONARY EQUIPMENT Emission Standards and Related Requirements § 1060.102 What permeation...

40 CFR 1060.103 - What permeation emission control requirements apply for fuel tanks?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false What permeation emission control... AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EVAPORATIVE EMISSIONS FROM NEW AND IN-USE NONROAD AND STATIONARY EQUIPMENT Emission Standards and Related Requirements § 1060.103 What permeation...

Molecular structure, photoluminescent and electroluminescent properties of bis(2-(4-methyl-2-hydroxyphenyl)benzothiazolate) zinc with excellent electron-transport characteristics

International Nuclear Information System (INIS)

Xu Huixia; Xu Bingshe; Fang Xiaohong; Yue Yan; Chen Liuqing; Wang Hua; Hao Yuying

2011-01-01

Highlights: → The synthesis, crystal structure and photophysical properties of Zn(4-MeBTZ) 2 were reported. → The electron-transport property was investigated by theoretical calculations and experimental. → We found that Zn(4-MeBTZ) 2 has a higher electron mobility than that of [Zn(BTZ) 2 ] 2 and the devices based on it have a lower turn-on voltage. - Abstract: In this article, the molecular structure, photoluminescent and electroluminescent properties of bis(2-(4-methyl-2-hydroxyphenyl) benzothiazolate) zinc (Zn(4-MeBTZ) 2 ) with good electron-transport characteristics were reported. This complex was identified as triclinic structure with the strong intermolecular π-π stacking interactions between the benzothiazolate/phenoxido rings and weak intramolecular hydrogen bonds by X-ray single-crystal diffraction. Quantum chemical method has been employed to investigate electron structure and charge transport property. The blue-green light emission was observed by fabricating double-layer devices using Zn(4-MeBTZ) 2 as electron-transport and NPB as hole-transport material. The performance of organic light-emitting devices based on Zn(4-MeBTZ) 2 is much better than that of the devices based on [Zn(BTZ) 2 ] 2 .

White-emissive tandem-type hybrid organic/polymer diodes with (0.33, 0.33) chromaticity coordinates.

Science.gov (United States)

Guo, Tzung-Fang; Wen, Ten-Chin; Huang, Yi-Shun; Lin, Ming-Wei; Tsou, Chuan-Cheng; Chung, Chia-Tin

2009-11-09

This study reports fabrication of white-emissive, tandem-type, hybrid organic/polymer light-emitting diodes (O/PLED). The tandem devices are made by stacking a blue-emissive OLED on a yellow-emissive phenyl-substituted poly(para-phenylene vinylene) copolymer-based PLED and applying an organic oxide/Al/molybdenum oxide (MoO(3)) complex structure as a connecting structure or charge-generation layer (CGL). The organic oxide/Al/MoO(3) CGL functions as an effective junction interface for the transport and injection of opposite charge carriers through the stacked configuration. The electroluminescence (EL) spectra of the tandem-type devices can be tuned by varying the intensity of the emission in each emissive component to yield the visible-range spectra from 400 to 750 nm, with Commission Internationale de l'Eclairage chromaticity coordinates of (0.33, 0.33) and a high color rendering capacity as used for illumination. The EL spectra also exhibit good color stability under various bias conditions. The tandem-type device of emission with chromaticity coordinates, (0.30, 0.31), has maximum brightness and luminous efficiency over 25,000 cd/m(2) and approximately 4.2 cd/A, respectively.

Optimal control for integrated emission management in diesel engines

NARCIS (Netherlands)

Donkers, M.C.F.; van Schijndel, J.; Heemels, W.P.M.H.; Willems, F.

2017-01-01

Integrated Emission Management (IEM) is a supervisory control strategy that minimises operational costs (consisting of fuel and AdBlue) for diesel engines with an aftertreatment system, while satisfying emission constraints imposed by legislation. In most work on IEM, a suboptimal heuristic

Optimal control for integrated emission management in diesel engines

NARCIS (Netherlands)

Donkers, M.C.F.; Schijndel, J. van; Heemels, W.P.M.H.; Willems, F.P.T.

2016-01-01

Integrated Emission Management (IEM) is a supervisory control strategy that minimises operational costs (consisting of fuel and AdBlue) for diesel engines with an aftertreatment system, while satisfying emission constraints imposed by legislation. In most work on IEM, a suboptimal heuristic

Revisiting factors controlling methane emissions from high-Arctic tundra

DEFF Research Database (Denmark)

Mastepanov, M.; Sigsgaard, C.; Tagesson, T.

2013-01-01

controlling methane emission, i.e. temperature and water table position. Late in the growing season CH4 emissions were found to be very similar between the study years (except the extremely dry 2010) despite large differences in climatic factors (temperature and water table). Late-season bursts of CH4...... short-term control factors (temperature and water table). Our findings suggest the importance of multiyear studies with a continued focus on shoulder seasons in Arctic ecosystems....

40 CFR 63.3555 - How do I determine the outlet THC emissions and add-on control device emission destruction or...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the outlet THC.../outlet Concentration Option § 63.3555 How do I determine the outlet THC emissions and add-on control... section to determine either the outlet THC emissions or add-on control device emission destruction or...

Study of energy transfer in single and multi-emissive layer using Gaussian peak fitting

International Nuclear Information System (INIS)

Yoon, Ju-An; Kim, You-Hyun; Kim, Nam Ho; Moon, Chang-Bum; He, Gufeng; Kim, Woo Young

2014-01-01

White organic light-emitting diodes(WOLEDs) were fabricated with the device structure of ITO(1800 Å)/NPB(700 Å)/emissive layer(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) using the two complementary colors method. Then, we investigated their electrical and optical characteristics to determine luminous efficiency, luminance and color coordinates of single, double, triple and quadruple emissive layered-WOLED. Thickness of emissive layer was fixed at 30 Å, and DPASN and BAlq were used for blue emissive host material and DCJTB was added as red dopant in the emissive layer. Then, we investigated the performance of OLEDs via its charge blocking structure and its different emissive region with emissive layers. Luminous efficiency of 5.30 cd/A at 50 mA/cm 2 of current density is obtained in WOLED device with double emissive layer of DPASN:DCJTB-0.1% (150 Å)/BAlq:DCJTB-0.1% (150 Å) and these are 80% higher than WOLED device with single emissive layer of DPASN:DCJTB-0.1% (300 Å). - Highlights: • White OLEDs with multiple-emissive layer were fabricated using p- and n-type emissive materials. • We fabricated WOLEDs only using a small quantity of fluorescent red dopant materials. • The spectroscopic analysis using multi-peak fits with a Gaussian function. • The explain electroluminescence spectra of white OLEDs with the multiple-emissive layer. • We examine changes in the number of emissive layer about white OLEDs performance

Using an ultra-thin non-doped orange emission layer to realize high efficiency white organic light-emitting diodes with low efficiency roll-off

Energy Technology Data Exchange (ETDEWEB)

Zhu, Liping; Chen, Jiangshan; Ma, Dongge, E-mail: mdg1014@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Graduate University of the Chinese Academy of Sciences, Changchun 130022 (China); Zhao, Yongbiao [Luminous Center of Excellence for Semiconductor Lighting and Displays, School of Electrical and Electronic Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, Singapore 639798 (Singapore); Zhang, Hongmei [Department of Materials Science and Engineering, Nanjing University of Posts and Telecommunications, Nanjing 210023 (China)

2014-06-28

By adopting an ultra-thin non-doped orange emission layer sandwiched between two blue emission layers, high efficiency white organic light-emitting diodes (WOLEDs) with reduced efficiency roll-off were fabricated. The optimized devices show a balanced white emission with Internationale de L'Eclairage of (0.41, 0.44) at the luminance of 1000 cd/m{sup 2}, and the maximum power efficiency, current efficiency (CE), and external quantum efficiency reach 63.2 lm/W, 59.3 cd/A, and 23.1%, which slightly shift to 53.4 lm/W, 57.1 cd/A, and 22.2% at 1000 cd/m{sup 2}, respectively, showing low efficiency roll-off. Detailed investigations on the recombination zone and the transient electroluminescence (EL) clearly reveal the EL processes of the ultra-thin non-doped orange emission layer in WOLEDs.

Photo/electroluminescence properties of an europium (III) complex doped in 4,4'-N,N'-dicarbazole-biphenyl matrix

International Nuclear Information System (INIS)

Zhou Yonghui; Zhou Liang; Wu, Jing; Li, Hong-Yan; Zheng Youxuan; You Xiaozeng; Zhang Hongjie

2010-01-01

The photoluminescence properties of one europium complex Eu(TFNB) 3 Phen (TFNB = 4,4,4-trifluoro-1-(naphthyl)-1,3-butanedione, Phen = 1,10-phenanthroline) doped in a hole-transporting material CBP (4,4'-N,N'-dicarbazole-biphenyl) films were studied. A series of organic light-emitting devices (OLEDs) using Eu(TFNB) 3 Phen as the emitter were fabricated with a multilayer structure of indium tin oxide, 250 Ω/square)/TPD (N,N'-diphenyl-N,N'-bis(3-methyllphenyl)-(1,1'-biphenyl)-4,4'-diamine, 50 nm)/Eu(TFNB) 3 phen (x): CBP (4,4'-N,N'-dicarbazole-biphenyl, 45 nm)/BCP (2,9-dimethyl-4,7-diphenyl-l,10 phenanthroline, 20 nm)/AlQ (tris(8-hydroxy-quinoline) aluminium, 30 nm)/LiF (1 nm)/Al (100 nm), where x is the weight percentage of Eu(TFNB) 3 phen doped in the CBP matrix (1-6%). A red emission at 612 nm with a half bandwidth of 3 nm, characteristic of Eu(III) ion, was observed with all devices. The device with a 3% dopant concentration shows the maximum luminance up to 1169 cd/m 2 (18 V) and the device with a 5% dopant concentration exhibits a current efficiency of 4.46 cd/A and power efficiency of 2.03 lm/W. The mechanism of the electroluminescence was also discussed.

Airborne radioactive emission control technology. Volume II

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, including uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking, a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

Airborne radioactive emission control technology. Volume III

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, including uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking, a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

Airborne radioactive emission control technology. Volume I

International Nuclear Information System (INIS)

Skoski, L.; Berlin, R.; Corby, D.; Clancy, J.; Hoopes, G.

1980-03-01

This report reviews the current and future control technology for airborne emissions from a wide variety of industries/facilities, includimg uranium mining and milling, other nuclear fuel cycle facilities, other NRC-licensed and DOE facilities, fossil fuel facilities, selected metal and non-metal extraction industries, and others. Where specific radioactivity control technology is lacking a description of any existing control technology is given. Future control technology is assessed in terms of improvements to equipment performance and process alterations. A catalogue of investigated research on advanced control technologies is presented

Highly red-shifted NIR emission from a novel anthracene conjugated polymer backbone containing Pt( ii ) porphyrins

KAUST Repository

Freeman, D. M. E.

2015-11-30

© The Royal Society of Chemistry 2016. We present the synthesis of a novel diphenylanthracene (DPA) based semiconducting polymer. The polymer is solubilised by alkoxy groups attached directly to a DPA monomer, meaning the choice of co-monomer is not limited to exclusively highly solubilising moieties. Interestingly, the polymer shows a red-shifted elecroluminescence maximum (510 nm) when compared to its photoluminescence maximum (450 nm) which we attribute to excimer formation. The novel polymer was utilised as a host for a covalently-linked platinum(ii) complexed porphyrin dopant. Emission from these polymers was observed in the NIR and again showed almost a 100 nm red shift from photoluminescence to electroluminescence. This work demonstrates that utilising highly aggregating host materials is an effective tool for inducing red-shifted emission in OLEDs.

Mercury emissions control technologies for mixed waste thermal treatment

International Nuclear Information System (INIS)

Chambers, A.; Knecht, M.; Soelberg, N.; Eaton, D.

1997-01-01

EPA has identified wet scrubbing at low mercury feedrates, as well as carbon adsorption via carbon injection into the offgas or via flow through fixed carbon beds, as control technologies that can be used to meet the proposed Maximum Achievable Control Technology (MACT) rule limit for mercury emissions from hazardous waste incinerators. DOE is currently funding demonstrations of gold amalgamation that may also control mercury to the desired levels. Performance data from a variety of sources was reviewed to determine ranges of achievable mercury control. Preliminary costs were estimated for using these technologies to control mercury emissions from mixed waste incineration. Mercury emissions control for mixed waste incineration may need to be more efficient than for incineration of other hazardous wastes because of higher mercury concentrations in some mixed waste streams. However, mercury control performance data for wet scrubbing and carbon adsorption is highly variable. More information is needed to demonstrate control efficiencies that are achievable under various design and operating conditions for wet scrubbing, carbon adsorption, and gold amalgamation technologies. Given certain assumptions made in this study, capital costs, operating costs, and lifecycle costs for carbon injection, carbon beds, and gold amalgamation generally vary for different assumed mercury feedrates and for different offgas flowrates. Assuming that these technologies can in fact provide the necessary mercury control performance, each of these technologies may be less costly than the others for certain mercury feedrates and the offgas flowrates

24 CFR 3280.308 - Formaldehyde emission controls for certain wood products.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Formaldehyde emission controls for certain wood products. 3280.308 Section 3280.308 Housing and Urban Development Regulations Relating to... Body and Frame Construction Requirements § 3280.308 Formaldehyde emission controls for certain wood...

The nature of trapping sites and recombination centres in PVK and PVK-PBD electroluminescent matrices seen by spectrally resolved thermoluminescence

International Nuclear Information System (INIS)

Glowacki, Ireneusz; Szamel, Zbigniew

2010-01-01

Two electroluminescent polymer matrices poly(N-vinylcarbazole) (PVK) and PVK with 40 wt% of 2-tert-butylphenyl-5-biphenyl-1,3,4-oxadiazole (PBD) were studied using spectrally resolved thermoluminescence (SRTL) in the temperature range 15-325 K. The comparison of the SRTL results with the electroluminescence (EL) spectra has allowed identification of the localized (trapping) sites and the radiative recombination centres present in the investigated matrices. In the neat PVK films deep traps with a depth about 200 meV, related to triplet excimers dominate, while in the PVK-PBD (40 wt%) blend films the traps that are related to triplet exciplexes formed by the carbazole groups and the PBD molecules dominate. Depth of the traps in the PVK-PBD blend is somewhat lower than that in the neat PVK. An analysis of the EL spectra shows that in the PVK and in the PVK-PBD blend the dominant radiative centres are singlet excimers and singlet exciplexes, respectively. However, in the neat PVK some contributions of the triplet monomer and the triplet excimer states in the EL were also detected.

Journal of Chemical Sciences | Indian Academy of Sciences

Indian Academy of Sciences (India)

Blue and white light electroluminescence in a multilayer OLED using a new aluminium complex · Pabitra K Nayak Neeraj Agarwal Farman Ali Meghan P Patankar K L Narasimhan N Periasamy · More Details Abstract Fulltext PDF. Synthesis, structure, optical absorption, emission and electroluminescence properties of a ...

Legislation, standards and methods for mercury emissions control

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-04-15

Mercury is an element of growing global concern. The United Nations Environment Programme plans to finalise and ratify a new global legally-binding convention on mercury by 2013. Canada already has legislation on mercury emissions from coal-fired utilities and the USA has recently released the new Mercury and Air Toxics Standard. Although other countries may not have mercury-specific legislation as such, many have legislation which results in significant co-benefit mercury reduction due to the installation of effective flue-gas cleaning technologies. This report reviews the current situation and trends in mercury emission legislation and, where possible, discusses the actions that will be taken under proposed or impending standards globally and regionally. The report also reviews the methods currently applied for mercury control and for mercury emission measurement with emphasis on the methodologies most appropriate for compliance. Examples of the methods of mercury control currently deployed in the USA, Canada and elsewhere are included.

Environmental management control systems for carbon emissions

Directory of Open Access Journals (Sweden)

Nadia Di Giacomo

2017-04-01

Full Text Available Purpose – This paper aims to focus on a global consulting company and examine how it struggled to establish an effective environmental management control system for carbon emissions for its employees’ air travel. The organisation was motivated to reduce its carbon emissions both to comply with regulation and to enhance or maintain corporate reputation. Design/methodology/approach – The paper takes a case study approach, examining internal and external documents as well as conducting interviews with senior staff. Findings – The case study investigates how Beta’s management implemented a system to reduce carbon emissions. The organisation focused on air travel, but the study finds that employee travel preferences did not radically change. Rather than reduction in carbon emissions, as planned by head office, air travel carbon emissions actually increased during the period, and, as a consequence, the reported reduction targets were significantly adjusted downwards to meet the new realities. Practical implications – The study has implications for both policy and practice for organisations seeking to improve their sustainability performance. Originality/value – The study responds to calls in the literature to undertake research to identify how management practices might reduce negative sustainability impacts, as there is little evidence of what management practices and accounting tools are being adopted, particularly in relation to carbon emissions from air travel. The paper adds to the creation of new accounting, giving visibility to carbon emission management through case study analysis.

Waterbury, Conn., Incinerator to Control Mercury Emissions

Science.gov (United States)

Emission control equipment to limit the discharge of mercury pollution to the atmosphere will be installed at an incinerator owned by the City of Waterbury, Conn., according to a proposed agreement between the city and federal government.

Controlling the emission current from a plasma cathode

International Nuclear Information System (INIS)

Bagaev, S.P.; Gushenets, V.I.; Schanin, P.M.

1993-01-01

The processes determining the time and amplitude characteristics of the grid-controlled electron emission from the plasma of an arc discharge have been analyzed. It has been shown that by applying to the grid confining the plasma emission boundary of a modulated voltage it is possible to form current pulse of up to 1 kA with nanosecond risetimes and falltimes and a pulse repetitive rate of 100 kHz

High-resolution optical coherence tomography using broadband light source with strain-controlled InAs/GaAs quantum dots

Energy Technology Data Exchange (ETDEWEB)

Tsubaki, Ippei; Harada, Yukihiro; Kita, Takashi [Department of Electrical and Electronic Engineering, Graduate School of Engineering, Kobe University, 1-1 Rokkodai, Nada, Kobe 657-8501 (Japan)

2012-12-15

Recently, there has been an increasing interest in broadband light sources to develop a biomolecular imaging technique called optical coherence tomography (OCT). We fabricated superluminescent diodes (SLDs) using three kinds of quantum dot (QD) layers with different emission wavelength in the active region. The emission wavelength was controlled by reducing the strain in QDs by using In{sub 0.1}Ga{sub 0.9}As strain-reducing layer. The SLD device showed a broad electroluminescence spectrum with the center wavelength of 1104 nm and the spectral linewidth of 122 nm at the injection of 40 mA, which corresponds to the theoretical axial resolution of 4.4 {mu}m. To estimate the actual resolution of the OCT system using fabricated SLD, we measured the interference signal in the Michelson interferometer. An axial resolution of 5.4 {mu}m, which is close to the theoretical limit, was obtained (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Air Pollutant Emissions Projections for the Cement and Steel Industry in China and the Impact of Emissions Control Technologies

Energy Technology Data Exchange (ETDEWEB)

Hasanbeigi, Ali [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Khanna, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Price, Lynn [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2017-03-01

China’s cement and steel industry accounts for approximately half of the world’s total cement and steel production. These two industries are two of the most energy-intensive and highest carbon dioxide (CO₂)-emitting industries and two of the key industrial contributors to air pollution in China. For example, the cement industry is the largest source of particulate matter (PM) emissions in China, accounting for 40 percent of its industrial PM emissions and 27 percent of its total national PM emissions. The Chinese steel industry contributed to approximately 20 percent of sulfur dioxide (SO_{2) emissions and 27 percent of PM emissions for all key manufacturing industries in China in 2013. In this study, we analyzed and projected the total PM and SO2 emissions from the Chinese cement and steel industry from 2010–2050 under three different scenarios: a Base Case scenario, an Advanced scenario, and an Advanced EOP (end-of-pipe) scenario. We used bottom-up emissions control technologies data and assumptions to project the emissions. In addition, we conducted an economic analysis to estimate the cost for PM emissions reductions in the Chinese cement industry using EOP control technologies, energy efficiency measures, and product change measures. The results of the emissions projection showed that there is not a substantial difference in PM emissions between the Base Case and Advanced scenarios, for both the cement and steel industries. This is mainly because PM emissions in the cement industry caused mainly by production process and not the fuel use. Since our forecast for the cement production in the Base Case and Advanced scenarios are not too different from each other, this results in only a slight difference in PM emissions forecast for these two scenarios. Also, we assumed a similar share and penetration rate of control technologies from 2010 up to 2050 for these two scenarios for the cement and steel industry. However, the Advanced EOP}

Modeling of Control Costs, Emissions, and Control Retrofits for Cost Effectiveness and Feasibility Analyses

Science.gov (United States)

Learn about EPA’s use of the Integrated Planning Model (IPM) to develop estimates of SO2 and NOx emission control costs, projections of futureemissions, and projections of capacity of future control retrofits, assuming controls on EGUs.

2-(2-Hydroxyphenyl)imidazole-based four-coordinate organoboron compounds with efficient deep blue photoluminescence and electroluminescence.

Science.gov (United States)

Zhang, Zhenyu; Zhang, Zuolun; Zhang, Hongyu; Wang, Yue

2017-12-19

Two new four-coordinate organoboron compounds with 2-(2-hydroxyphenyl)imidazole derivatives as the chelating ligands have been synthesized. They possess high thermal stability and are able to form an amorphous glass state. Crystallographic analyses indicate that the differences in ligand structure cause the change of ππ stacking character. The CH 2 Cl 2 solutions and thin films of these compounds display bright blue emission, and these compounds have appropriate HOMO and LUMO energy levels for carrier injection in OLEDs. By utilizing the good thermal and luminescent properties, as well as the proper frontier orbital energy levels, bright non-doped OLEDs with a simple structure have been realized. Notably, these simple devices show deep blue electroluminescence with the Commission Internationale de l'Éclairage (CIE) coordinate of ca. (0.16, 0.08), which is close to the CIE coordinate of (0.14, 0.08) for standard blue defined by the National Television System Committee. In addition, one of the devices exhibits good performance, showing brightness, current efficiency, power efficiency and external quantum efficiency up to 2692 cd m -2 , 2.50 cd A -1 , 1.81 lm W -1 and 3.63%, respectively. This study not only provides good deep-blue emitting OLED materials that are rarely achieved by using four-coordinate organoboron compounds, but also allows a deeper understanding of the structure-property relationship of 2-(2-hydroxyphenyl)imidazole-based boron complexes, which benefits the further structural design of this type of material.

Development and construction of a programmable generator of luminous impulses

International Nuclear Information System (INIS)

Sahuc, P.

1989-01-01

The design and construction of an impulse generator, for light waves, designed to control the characteristics of a scintillator. In these detectors, a particle gives rise to the emission of a luminous signal, which must be transformed in an electrical signal. In the present work, photomultipliers are used as luminous-electrical signal converters. The principles of operation of a scintillator, of a scintillator connected with a photodiode, and of a scintillator connected with a photomultiplier are reviewed. The analysis of the performance and of the possibilies offered by the usual generators of light, show that more suitable solutions are required. The characteristics of the electroluminescent diodes, their performances, concerning light emission and power, are investigated. The principles, the operating conditions and the performances of a generator of light, applying electroluminescent diodes, are examined. The construction and the results obtained with a prototype are presented [fr

Observation of red electroluminescence from an Eu2O3/ p +-Si device and improved performance by introducing a Tb2O3 layer

International Nuclear Information System (INIS)

Yin, Xue; Wang, Shenwei; Mu, Guangyao; Wan, Guangmiao; Huang, Miaoling; Yi, Lixin

2017-01-01

We report red electroluminescence (EL) from an Eu 2 O 3 / p + -Si device with Eu 2 O 3 film annealed in oxygen ambient at 700 °C. The red EL is ascribed to the characteristic emissions of Eu 3+ ions in Eu 2 O 3 film and the luminescence mechanism is discussed in detail. In order to optimize the device performance, Eu 2 O 3 /Tb 2 O 3 multiple films were deposited on Si wafer, and the result showed EL intensity of the device was obviously enhanced and the turn-on voltage was reduced to about 10 V. Moreover, intensity ratio I ( 5 D 0 – 7 F 2 )/ I ( 5 D 0 – 7 F 1 ) was also significantly increased with the hypersensitive transition 5 D 0 – 7 F 2 as the most prominent group at about 611 nm. The improved performance was attributed to the added Tb 2 O 3 film that it can be served as the hole-injection layer to afford extra holes injected into the Eu 2 O 3 layer. (paper)

Fast-regenerable sulfur dioxide adsorbents for diesel engine emission control

Science.gov (United States)

Li, Liyu [Richland, WA; King, David L [Richland, WA

2011-03-15

Disclosed herein are sorbents and devices for controlling sulfur oxides emissions as well as systems including such sorbents and devices. Also disclosed are methods for making and using the disclosed sorbents, devices and systems. In one embodiment the disclosed sorbents can be conveniently regenerated, such as under normal exhaust stream from a combustion engine, particularly a diesel engine. Accordingly, also disclosed are combustion vehicles equipped with sulfur dioxide emission control devices.

Pulsed Electrical Spin Injection into InGaAs Quantum Dots: Studies of the Electroluminescence Polarization Dynamics

International Nuclear Information System (INIS)

Asshoff, P.; Loeffler, W.; Fluegge, H.; Zimmer, J.; Mueller, J.; Westenfelder, B.; Hu, D. Z.; Schaadt, D. M.; Kalt, H.; Hetterich, M.

2010-01-01

We present time-resolved studies of the spin polarization dynamics during and after initialization through pulsed electrical spin injection into InGaAs quantum dots embedded in a p-i-n-type spin-injection light-emitting diode. Experiments are performed with pulse widths in the nanosecond range and a time-resolved single photon counting setup is used to detect the subsequent electroluminescence. We find evidence that the achieved spin polarization shows an unexpected temporal behavior, attributed mainly to many-carrier and non-equilibrium effects in the device.

Controlling nitrous oxide emissions from grassland livestock production systems

NARCIS (Netherlands)

Oenema, O.; Gebauer, G.; Rodriguez, M.; Sapek, A.; Jarvis, S.C.; Corré, W.J.; Yamulki, S.

1998-01-01

There is growing awareness that grassland livestock production systems are major sources of nitrous oxide (N2O). Controlling these emissions requires a thorough understanding of all sources and controlling factors at the farm level. This paper examines the various controlling factors and proposes

Control technology for radioactive emissions to the atmosphere at US Department of Energy facilities

Energy Technology Data Exchange (ETDEWEB)

Moore, E.B.

1984-10-01

The purpose of this report is to provide information to the US Environmental Protection agency (EPA) on existing technology for the control of radionuclide emissions into the air from US Department of Energy (DOE) facilities, and to provide EPA with information on possible additional control technologies that could be used to further reduce these emissions. Included in this report are generic discussions of emission control technologies for particulates, iodine, rare gases, and tritium. Also included are specific discussions of existing emission control technologies at 25 DOE facilities. Potential additional emission control technologies are discussed for 14 of these facilities. The facilities discussed were selected by EPA on the basis of preliminary radiation pathway analyses. 170 references, 131 figures, 104 tables.

Control technology for radioactive emissions to the atmosphere at US Department of Energy facilities

International Nuclear Information System (INIS)

Moore, E.B.

1984-10-01

The purpose of this report is to provide information to the US Environmental Protection agency (EPA) on existing technology for the control of radionuclide emissions into the air from US Department of Energy (DOE) facilities, and to provide EPA with information on possible additional control technologies that could be used to further reduce these emissions. Included in this report are generic discussions of emission control technologies for particulates, iodine, rare gases, and tritium. Also included are specific discussions of existing emission control technologies at 25 DOE facilities. Potential additional emission control technologies are discussed for 14 of these facilities. The facilities discussed were selected by EPA on the basis of preliminary radiation pathway analyses. 170 references, 131 figures, 104 tables

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Date Report No. 3: Diesel Fuel Sulfur Effects on Particulate Matter Emissions

Energy Technology Data Exchange (ETDEWEB)

DOE; ORNL; NREL; EMA; MECA

1999-11-15

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim report covers the effects of diesel fuel sulfur level on particulate matter emissions for four technologies.

Emission Control Technologies for Thermal Power Plants

Science.gov (United States)

Nihalani, S. A.; Mishra, Y.; Juremalani, J.

2018-03-01

Coal thermal power plants are one of the primary sources of artificial air emissions, particularly in a country like India. Ministry of Environment and Forests has proposed draft regulation for emission standards in coal-fired power plants. This includes significant reduction in sulphur-dioxide, oxides of nitrogen, particulate matter and mercury emissions. The first step is to evaluate the technologies which represent the best selection for each power plant based on its configuration, fuel properties, performance requirements, and other site-specific factors. This paper will describe various technology options including: Flue Gas Desulfurization System, Spray Dryer Absorber (SDA), Circulating Dry Scrubber (CDS), Limestone-based Wet FGD, Low NOX burners, Selective Non Catalytic Reduction, Electrostatic Precipitator, Bag House Dust Collector, all of which have been evaluated and installed extensively to reduce SO2, NOx, PM and other emissions. Each control technology has its advantages and disadvantages. For each of the technologies considered, major features, potential operating and maintenance cost impacts, as well as key factors that contribute to the selection of one technology over another are discussed here.

Thermo-optical properties of 1H[3,4-b] quinoline films used in electroluminescent devices

Science.gov (United States)

Jaglarz, Janusz; Kępińska, Mirosława; Sanetra, Jerzy

2014-06-01

Electroluminescence cells with H[3,4-b] quinoline layers are promising devices for a blue light emitting EL diode. This work measured the optical reflectance as a function of temperature in copolymers PAQ layers deposited on Si crystalline substrate. Using the extended Cauchy dispersion model of the film refractive index we determined the thermo-optical coefficients for quinoline layers in the temperature range of 76-333 K from combined ellipsometric and spectrofotometric studies. The obtained values of thermo-optical coefficients of thin PAQ film, were negative and ranged in 5-10 × 10-4 [1/K].

Photo- and electro-luminescence of rare earth doped ZnO electroluminors at liquid nitrogen temperature

International Nuclear Information System (INIS)

Bhushan, S.; Kaza, B.R.; Pandey, A.N.

1981-01-01

Photo (PL) and electroluminescent (EL) spectra of some rare earth (La, Gd, Er or Dy) doped ZnO electroluminors have been investigated at liquid nitrogen temperature (LNT) and compared with their corresponding results at room temperature (RT). In addition to three bands observed at RT, one more band on the higher wavelength side appears in EL spectra. Spectral shift with the exciting intensity at LNT supports the donor-acceptor (DA) model in which the rare earths form the donor levels. From the temperature dependent studies of PL and EL brightness, the EL phenomenon is found to be more susceptible to traps. (author)

Study on the visibility of an electroluminescent display for automobiles; Jidoshayo EL display no shininsei

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, N; Harada, M; Idogaki, T [Denso Corp., Aichi (Japan)

1997-10-01

This report explores the visibility of an Electroluminescent (EL) display for automotive use. Displays for automobiles are exposed to the direct rays of the sun and forced to operate in wide temperature range. Therefore, luminous flux density by the lighting on EL display panel and operating environment temperature must be considered for the visibility evaluation. Sensory evaluation on the visibility and physical measurements such as contrast, chromaticity difference in accordance with the viewing angle change indicate that the visibility of the EL display for automobiles is advantageous over other displays. 6 refs., 11 figs., 1 tab.

Energy-related carbon dioxide emissions: control targets and long term policy strategies

International Nuclear Information System (INIS)

Haites, E.

1993-01-01

A number of countries have unilaterally committed themselves to limit emissions of greenhouse gases. Other countries have resisted such commitments; they prefer to engage in further climate research to determine the extent of any emissions reduction that may be necessary before committing themselves to significant costs to implement controls. This paper examines the costs of alternative policies including immediate action to limit emissions and climate research followed by controls if necessary. (Author)

DEMONSTRATION OF AN ADVANCED INTEGRATED CONTROL SYSTEM FOR SIMULTANEOUS EMISSIONS REDUCTION

Energy Technology Data Exchange (ETDEWEB)

Suzanne Shea; Randhir Sehgal; Ilga Celmins; Andrew Maxson

2002-02-01

The primary objective of the project titled ''Demonstration of an Advanced Integrated Control System for Simultaneous Emissions Reduction'' was to demonstrate at proof-of-concept scale the use of an online software package, the ''Plant Environmental and Cost Optimization System'' (PECOS), to optimize the operation of coal-fired power plants by economically controlling all emissions simultaneously. It combines physical models, neural networks, and fuzzy logic control to provide both optimal least-cost boiler setpoints to the boiler operators in the control room, as well as optimal coal blending recommendations designed to reduce fuel costs and fuel-related derates. The goal of the project was to demonstrate that use of PECOS would enable coal-fired power plants to make more economic use of U.S. coals while reducing emissions.

Multi-objective optimisation of wastewater treatment plant control to reduce greenhouse gas emissions.

Science.gov (United States)

Sweetapple, Christine; Fu, Guangtao; Butler, David

2014-05-15

This study investigates the potential of control strategy optimisation for the reduction of operational greenhouse gas emissions from wastewater treatment in a cost-effective manner, and demonstrates that significant improvements can be realised. A multi-objective evolutionary algorithm, NSGA-II, is used to derive sets of Pareto optimal operational and control parameter values for an activated sludge wastewater treatment plant, with objectives including minimisation of greenhouse gas emissions, operational costs and effluent pollutant concentrations, subject to legislative compliance. Different problem formulations are explored, to identify the most effective approach to emissions reduction, and the sets of optimal solutions enable identification of trade-offs between conflicting objectives. It is found that multi-objective optimisation can facilitate a significant reduction in greenhouse gas emissions without the need for plant redesign or modification of the control strategy layout, but there are trade-offs to consider: most importantly, if operational costs are not to be increased, reduction of greenhouse gas emissions is likely to incur an increase in effluent ammonia and total nitrogen concentrations. Design of control strategies for a high effluent quality and low costs alone is likely to result in an inadvertent increase in greenhouse gas emissions, so it is of key importance that effects on emissions are considered in control strategy development and optimisation. Copyright © 2014 Elsevier Ltd. All rights reserved.

Modulating emission intensity of GaN-based green light emitting diodes on c-plane sapphire

International Nuclear Information System (INIS)

Du, Chunhua; Ma, Ziguang; Zhou, Junming; Lu, Taiping; Jiang, Yang; Jia, Haiqiang; Liu, Wuming; Chen, Hong

2014-01-01

The asymmetric dual-wavelength (green/blue) coupled InGaN/GaN multiple quantum wells were proposed to modulate the green emission intensity. Electroluminescent measurements demonstrate the conspicuous increment of the green light intensity by decreasing the coupled barrier thickness. This was partly attributed to capture of more carriers when holes tunnel across the thinner barrier from the blue quantum wells, as a hole reservoir, to the green quantum wells. While lower effective barrier height of the blue quantum wells benefits improved hole transportation from p-GaN to the active region. Efficiency droop of the green quantum wells was partially alleviated due to the enhanced injection efficiency of holes

Control of combustion generated emissions from spark ignition engines: a review

International Nuclear Information System (INIS)

Mansha, M.; Shahid, E.M.; Qureshi, A.H.

2012-01-01

For the past several decades automobiles have been a major source of ground level emissions of various pollutants like CO, HC, NO/sub x/, SO/sub x/ CO/sub 2/, etc. Due to their dangerous effects on human health, vegetation and on climate, various pre combustion, in-cylinder and post. combustion techniques have been tried for their abatement. This paper reviews all of the workable measures taken so far to controlling the combustion generated emissions from 4-stroke Spark Ignition Vehicular Engines ever since the promulgation of emission control legislation/standards and their subsequent enforcement in the late 1960s. (author)

Controlled ultrasound-induced blood-brain barrier disruption using passive acoustic emissions monitoring.

Directory of Open Access Journals (Sweden)

Costas D Arvanitis

Full Text Available The ability of ultrasonically-induced oscillations of circulating microbubbles to permeabilize vascular barriers such as the blood-brain barrier (BBB holds great promise for noninvasive targeted drug delivery. A major issue has been a lack of control over the procedure to ensure both safe and effective treatment. Here, we evaluated the use of passively-recorded acoustic emissions as a means to achieve this control. An acoustic emissions monitoring system was constructed and integrated into a clinical transcranial MRI-guided focused ultrasound system. Recordings were analyzed using a spectroscopic method that isolates the acoustic emissions caused by the microbubbles during sonication. This analysis characterized and quantified harmonic oscillations that occur when the BBB is disrupted, and broadband emissions that occur when tissue damage occurs. After validating the system's performance in pilot studies that explored a wide range of exposure levels, the measurements were used to control the ultrasound exposure level during transcranial sonications at 104 volumes over 22 weekly sessions in four macaques. We found that increasing the exposure level until a large harmonic emissions signal was observed was an effective means to ensure BBB disruption without broadband emissions. We had a success rate of 96% in inducing BBB disruption as measured by in contrast-enhanced MRI, and we detected broadband emissions in less than 0.2% of the applied bursts. The magnitude of the harmonic emissions signals was significantly (P<0.001 larger for sonications where BBB disruption was detected, and it correlated with BBB permeabilization as indicated by the magnitude of the MRI signal enhancement after MRI contrast administration (R(2 = 0.78. Overall, the results indicate that harmonic emissions can be a used to control focused ultrasound-induced BBB disruption. These results are promising for clinical translation of this technology.

Polarization control of spontaneous emission for rapid quantum-state initialization

Science.gov (United States)

DiLoreto, C. S.; Rangan, C.

2017-04-01

We propose an efficient method to selectively enhance the spontaneous emission rate of a quantum system by changing the polarization of an incident control field, and exploiting the polarization dependence of the system's spontaneous emission rate. This differs from the usual Purcell enhancement of spontaneous emission rates as it can be selectively turned on and off. Using a three-level Λ system in a quantum dot placed in between two silver nanoparticles and a linearly polarized, monochromatic driving field, we present a protocol for rapid quantum state initialization, while maintaining long coherence times for control operations. This process increases the overall amount of time that a quantum system can be effectively utilized for quantum operations, and presents a key advance in quantum computing.

Delay-feedback control strategy for reducing CO2 emission of traffic flow system

Science.gov (United States)

Zhang, Li-Dong; Zhu, Wen-Xing

2015-06-01

To study the signal control strategy for reducing traffic emission theoretically, we first presented a kind of discrete traffic flow model with relative speed term based on traditional coupled map car-following model. In the model, the relative speed difference between two successive running cars is incorporated into following vehicle's acceleration running equation. Then we analyzed its stability condition with discrete control system stability theory. Third, we designed a delay-feedback controller to suppress traffic jam and decrease traffic emission based on modern controller theory. Last, numerical simulations are made to support our theoretical results, including the comparison of models' stability analysis, the influence of model type and signal control on CO2 emissions. The results show that the temporal behavior of our model is superior to other models, and the traffic signal controller has good effect on traffic jam suppression and traffic CO2 emission, which fully supports the theoretical conclusions.

Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

Science.gov (United States)

Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

2015-12-01

Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference

Influence of gamma-irradiation on the electroluminescence of ZnSe:Zn,Te crystals

International Nuclear Information System (INIS)

Elmuratova, D.B.; Ibragimova, E.M.

2007-01-01

Effect of 60 Co gamma-radiation at the dose rate of 10 Gy/s on electroluminescence (El)Zn Se crystals with 0.5 weight % Te treated in zinc vapor was studied for possible manufacturing of light emitting structures. Broad El band with the maximum at 610 nm is excited in the origin samples at a voltage above 15 V. After irradiation to the high dose of 10 6 Gy the El intensity grows by ∼2.5 times in the direct polarity at 24 V. The observed El of Zn Se:Zn,Te single crystals is assumed to be caused by the charge carrier recombination at the interstitial zinc centers by the excitation mechanism of a barrier sub breakdown type (authors)

Investigations of the Impact of Biodiesel Metal Contaminants on Emissions Control Devices

Energy Technology Data Exchange (ETDEWEB)

Brookshear, D. W.; Lance, M. J.; McCormick, Robert L.; Toops, T. J.

2017-02-27

Biodiesel is a renewable fuel with the potential to displace a portion of petroleum use. However, as with any alternative fuel, in order to be a viable choice it must be compatible with the emissions control devices. The finished biodiesel product can contain up to 5 ppm Na+K and 5 ppm Ca+Mg, and these metal impurities can lead to durability issues with the devices used to control emissions in diesel vehicles. Significant work has been performed to understand how the presence of these metals impacts each individual component of diesel emissions control systems, and this chapter summarizes the findings of these research efforts.

Controls of nitrous oxide emission after simulated cattle urine deposition

DEFF Research Database (Denmark)

Baral, Khagendra Raj; Thomsen, Anton Gårde; Olesen, Jørgen E

2014-01-01

Urine deposited during grazing is a significant source of atmospheric nitrous oxide (N2O). The potential for N2O emissions from urine patches is high, and a better understanding of controls is needed. This study investigated soil nitrogen (N) dynamics and N2O emissions from cattle urine...

Poly[(arylene ethynylene)-alt-(arylene vinylene)]s based on anthanthrone and its derivatives: synthesis and photophysical, electrochemical, electroluminescent, and photovoltaic properties

Czech Academy of Sciences Publication Activity Database

John, S. V.; Cimrová, Věra; Ulbricht, C.; Pokorná, Veronika; Růžička, Aleš; Giguére, J.-B.; Lafleur-Lambert, A.; Morin, J.-F.; Iwuoha, E.; Egbe, D. A. M.

2017-01-01

Roč. 50, č. 21 (2017), s. 8357-8371 ISSN 0024-9297 R&D Projects: GA ČR(CZ) GA13-26542S Institutional support: RVO:61389013 Keywords : polycyclic aromatic compounds * anthanthrones and anthanthrone derivatives * electroluminescence Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 5.835, year: 2016

Excitation spectra and forward injection electroluminescence of Er/sup 3+/ ions in ZnS

International Nuclear Information System (INIS)

Jiaqi, Y.; Tianren, Z.; Wenlian, L.

1985-01-01

Trivalent rare earth ions (RE/sup 3+/) are efficient luminescent centers for electroluminescence (EL) of thin films of II-VI compounds, which are promising display materials and attract more and more attention. The mechanism of all EL devices of RE/sup 3+/ available so far is hot electron impact excitation. Based on the analysis of excitation spectra of RE/sup 3+/ in ZnS, the authors have pointed out the possibility of a new type of EL of RE/sup 3+/ - forward injection EL, which have potential of reducing operation voltage and raising efficiency. The forward injection EL of RE/sup 3+/ has been observed and experimentally proven in ZnS:Er/sup 3+/ diode for the first time

Soil acidification in China: is controlling SO2 emissions enough?

Science.gov (United States)

Zhao, Yu; Duan, Lei; Xing, Jia; Larssen, Thorjorn; Nielsen, Chris P; Hao, Jiming

2009-11-01

Facing challenges of increased energy consumption and related regional air pollution, China has been aggressively implementing flue gas desulfurization (FGD) and phasing out small inefficient units in the power sector in order to achieve the national goal of 10% reduction in sulfur dioxide (SO(2)) emissions from 2005 to 2010. In this paper, the effect of these measures on soil acidification is explored. An integrated methodology is used, combining emission inventory data, emission forecasts, air quality modeling, and ecological sensitivities indicated by critical load. National emissions of SO(2), oxides of nitrogen (NO(X)), particulate matter (PM), and ammonia (NH(3)) in 2005 were estimated to be 30.7, 19.6, 31.3, and 16.6 Mt, respectively. Implementation of existing policy will lead to reductions in SO(2) and PM emissions, while those of NO(X) and NH(3) will continue to rise, even under tentatively proposed control measures. In 2005, the critical load for soil acidification caused by sulfur (S) deposition was exceeded in 28% of the country's territory, mainly in eastern and south-central China. The area in exceedance will decrease to 26% and 20% in 2010 and 2020, respectively, given implementation of current plans for emission reductions. However, the exceedance of the critical load for nitrogen (N, combining effects of eutrophication and acidification) will double from 2005 to 2020 due to increased NO(X) and NH(3) emissions. Combining the acidification effects of S and N, the benefits of SO(2) reductions during 2005-2010 will almost be negated by increased N emissions. Therefore abatement of N emissions (NO(X) and NH(3)) and deposition will be a major challenge to China, requiring policy development and technology investments. To mitigate acidification in the future, China needs a multipollutant control strategy that integrates measures to reduce S, N, and PM.

Air pollutant emissions and their control with the focus on waste incineration facilities

Energy Technology Data Exchange (ETDEWEB)

Loeschau, Margit [Wandschneider + Gutjahr, Hamburg (Germany)

2017-07-01

This text and practical handbook thoroughly presents the control of air pollutant emissions from combustion processes focusing on waste incinerators. Special characteristics are emphasised and the differences to emission control from combustion processes with other fuels are explained. The author illustrates the origin and effects of air pollutants from incineration processes, the mechanics of their appearance in the incineration process, primary and secondary measures for their reduction, processes of measuring the emissions as well as the methods of disposing the residues. In particular, the pros and cons of procedural steps and their appropriate combination under various conditions are emphasised. Moreover, the book contains information and analyses of the emissions situation, the consumption of operating materials and of backlog quantities as well as of the cost structure of waste incinerators with regard to their applied control system. Furthermore, the author explicates the contemporary legal, scientific and technological developments and their influence on air pollutant emission control. An evaluation of the status quo of air pollutant control at waste incinerators in Germany, practical examples about possible combinations and typical performance data complete the content. Accordingly, this book is a guideline for planing a reasonable overall concept of an air pollutant control that takes the location and the segregation tasks into consideration.

40 CFR 270.315 - What air emissions control information must I keep at my facility?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false What air emissions control information... Facility § 270.315 What air emissions control information must I keep at my facility? If you have air emission control equipment subject to 40 CFR part 264, subpart CC, you must keep the following information...

Reducing CO2 emissions in temperature-controlled road transportation using the LDVRP model

NARCIS (Netherlands)

Stellingwerf, Helena M.; Kanellopoulos, Argyris; Vorst, van der Jack G.A.J.; Bloemhof, Jacqueline M.

2018-01-01

Temperature-controlled transport is needed to maintain the quality of products such as fresh and frozen foods and pharmaceuticals. Road transportation is responsible for a considerable part of global emissions. Temperature-controlled transportation exhausts even more emissions than ambient

LANDFILL OPERATION FOR CARBON SEQUESTRATION AND MAXIMUM METHANE EMISSION CONTROL

Energy Technology Data Exchange (ETDEWEB)

Don Augenstein

1999-01-11

''Conventional'' waste landfills emit methane, a potent greenhouse gas, in quantities such that landfill methane is a major factor in global climate change. Controlled landfilling is a novel approach to manage landfills for rapid completion of total gas generation, maximizing gas capture and minimizing emissions of methane to the atmosphere. With controlled landfilling, methane generation is accelerated and brought to much earlier completion by improving conditions for biological processes (principally moisture levels) in the landfill. Gas recovery efficiency approaches 100% through use of surface membrane cover over porous gas recovery layers operated at slight vacuum. A field demonstration project's results at the Yolo County Central Landfill near Davis, California are, to date, highly encouraging. Two major controlled landfilling benefits would be the reduction of landfill methane emissions to minuscule levels, and the recovery of greater amounts of landfill methane energy in much shorter times than with conventional landfill practice. With the large amount of US landfill methane generated, and greenhouse potency of methane, better landfill methane control can play a substantial role in reduction of US greenhouse gas emissions.

2D Semiconductors for Valley-Polarized LEDs and Photodetectors

Science.gov (United States)

Yu, Ting

The recently discovered two-dimensional (2D) semiconductors, such as transitional-metal-dichalcogenide monolayers, have aroused great interest due to the underlying quantum physics and the appealing optoelectronic applications like atomically thin light-emitting diodes (LEDs) and photodetectors. On the one hand, valley-polarized electroluminescence and photocurrent from such monolayers have not caused enough attention but highly demanded as building blocks for the new generation valleytronic applications. On the other hand, most reports on these devices are based on the mechanically exfoliated small samples. Considering real applications, a strategy which could offer mass-product and high compatibility to the current planar processes is greatly demanded. Large-area samples prepared by chemical vapour deposition (CVD) are perfect candidates towards such a goal. Here, we report electrically tunable valley-polarized electroluminescence and the selective spin-valley-coupled photocurrent in optoelectronic devices based on monolayer WS2 and MoS2 grown by CVD, exhibiting large electroluminescence and photocurrent dichroisms of 81% and 60%, respectively. The controllable valley polarization and emission components of the electroluminescence have been realized by varying electrical injection of carriers. For the observed helicity-dependent photocurrent, the circular photogalvanic effect at resonant excitations has been found to take the dominant responsibility.

Control of mercury emissions from coal-fired boilers

Energy Technology Data Exchange (ETDEWEB)

Huang, H.S.; Livengood, C.D.

1992-09-01

This project at Argonne is designed to investigate new concepts leading to advanced control technologies for fossil-energy systems. The objective of this new task on air toxics control is to develop new or improved, cost-effective control technology for the abatement of emissions of hazardous air pollutants (HAPs) from fossil-fuel combustion plants and to evaluate the possible effects of any captured species on waste disposal. The HAPs to be investigated initially in this task include mercury and arsenic compounds.

Control of mercury emissions from coal-fired boilers

Energy Technology Data Exchange (ETDEWEB)

Huang, H.S.; Livengood, C.D.

1992-01-01

This project at Argonne is designed to investigate new concepts leading to advanced control technologies for fossil-energy systems. The objective of this new task on air toxics control is to develop new or improved, cost-effective control technology for the abatement of emissions of hazardous air pollutants (HAPs) from fossil-fuel combustion plants and to evaluate the possible effects of any captured species on waste disposal. The HAPs to be investigated initially in this task include mercury and arsenic compounds.

Portuguese agriculture and the evolution of greenhouse gas emissions-can vegetables control livestock emissions?

Science.gov (United States)

Mourao, Paulo Reis; Domingues Martinho, Vítor

2017-07-01

One of the most serious externalities of agricultural activity relates to greenhouse gas emissions. This work tests this relationship for the Portuguese case by examining data compiled since 1961. Employing cointegration techniques and vector error correction models (VECMs), we conclude that the evolution of the most representative vegetables and fruits in Portuguese production are associated with higher controls on the evolution of greenhouse gas emissions. Reversely, the evolution of the output levels of livestock and the most representative animal production have significantly increased the level of CO 2 (carbon dioxide) reported in Portugal. We also analyze the cycle length of the long-term relationship between agricultural activity and greenhouse gas emissions. In particular, we highlight the case of synthetic fertilizers, whose values of CO 2 have quickly risen due to changes in Portuguese vegetables, fruit, and animal production levels.

Organic Light-Emitting Diodes Based on Phthalimide Derivatives: Improvement of the Electroluminescence Properties

Directory of Open Access Journals (Sweden)

Frédéric Dumur

2018-03-01

Full Text Available In this study, a phthalimide-based fluorescent material has been examined as a green emitter for multilayered organic light-emitting diodes (OLEDs. By optimizing the device stacking, a maximum brightness of 28,450 cd/m2 at 11.0 V and a maximum external quantum efficiency of 3.11% could be obtained. Interestingly, OLEDs fabricated with Fluo-2 presented a 20-fold current efficiency improvement compared to the previous results reported in the literature, evidencing the crucial role of the device stacking in the electroluminescence (EL performance of a selected emitter. Device lifetime was also examined and an operational stability comparable to that reported for a standard triplet emitter i.e., bis(4-methyl-2,5-diphenyl-pyridineiridium(III acetylacetonate [(mdppy2Iracac] was evidenced.

Effectiveness evaluation of temporary emission control action in 2016 in winter in Shijiazhuang, China

Directory of Open Access Journals (Sweden)

B. Liu

2018-05-01

Full Text Available To evaluate the environmental effectiveness of the control measures for atmospheric pollution in Shijiazhuang, China, a large-scale controlling experiment for emission sources of atmospheric pollutants (i.e. a temporary emission control action, TECA was designed and implemented during 1 November 2016 to 9 January 2017. Compared to the no-control action and heating period (NCAHP, under unfavourable meteorological conditions, the mean concentrations of PM2.5, PM10, SO2, NO2, and chemical species (Si, Al, Ca2+, Mg2+ in PM2.5 during the control action and heating period (CAHP still decreased by 8, 8, 5, 19, 30.3, 4.5, 47.0, and 45.2 %, respectively, indicating that the control measures for atmospheric pollution were effective. The effects of control measures in suburbs were better than those in urban area, especially for the control effects of particulate matter sources. The control effects for emission sources of carbon monoxide (CO were not apparent during the TECA period, especially in suburbs, likely due to the increasing usage of domestic coal in suburbs along with the temperature decreasing.The results of positive matrix factorization (PMF analysis showed that crustal dust, secondary sources, vehicle emissions, coal combustion and industrial emissions were main PM2.5 sources. Compared to the whole year (WY and the no-control action and no-heating period (NCANHP, the contribution concentrations and proportions of coal combustion to PM2.5 increased significantly during other stages of the TECA period. The contribution concentrations and proportions of crustal dust and vehicle emissions to PM2.5 decreased noticeably during the CAHP compared to other stages of the TECA period. The contribution concentrations and proportions of industrial emissions to PM2.5 during the CAHP decreased noticeably compared to the NCAHP. The pollutants' emission sources during the CAHP were in effective control, especially for crustal dust and vehicles. However

Effectiveness evaluation of temporary emission control action in 2016 in winter in Shijiazhuang, China

Science.gov (United States)

Liu, Baoshuang; Cheng, Yuan; Zhou, Ming; Liang, Danni; Dai, Qili; Wang, Lu; Jin, Wei; Zhang, Lingzhi; Ren, Yibin; Zhou, Jingbo; Dai, Chunling; Xu, Jiao; Wang, Jiao; Feng, Yinchang; Zhang, Yufen

2018-05-01

To evaluate the environmental effectiveness of the control measures for atmospheric pollution in Shijiazhuang, China, a large-scale controlling experiment for emission sources of atmospheric pollutants (i.e. a temporary emission control action, TECA) was designed and implemented during 1 November 2016 to 9 January 2017. Compared to the no-control action and heating period (NCAHP), under unfavourable meteorological conditions, the mean concentrations of PM2.5, PM10, SO2, NO2, and chemical species (Si, Al, Ca2+, Mg2+) in PM2.5 during the control action and heating period (CAHP) still decreased by 8, 8, 5, 19, 30.3, 4.5, 47.0, and 45.2 %, respectively, indicating that the control measures for atmospheric pollution were effective. The effects of control measures in suburbs were better than those in urban area, especially for the control effects of particulate matter sources. The control effects for emission sources of carbon monoxide (CO) were not apparent during the TECA period, especially in suburbs, likely due to the increasing usage of domestic coal in suburbs along with the temperature decreasing.The results of positive matrix factorization (PMF) analysis showed that crustal dust, secondary sources, vehicle emissions, coal combustion and industrial emissions were main PM2.5 sources. Compared to the whole year (WY) and the no-control action and no-heating period (NCANHP), the contribution concentrations and proportions of coal combustion to PM2.5 increased significantly during other stages of the TECA period. The contribution concentrations and proportions of crustal dust and vehicle emissions to PM2.5 decreased noticeably during the CAHP compared to other stages of the TECA period. The contribution concentrations and proportions of industrial emissions to PM2.5 during the CAHP decreased noticeably compared to the NCAHP. The pollutants' emission sources during the CAHP were in effective control, especially for crustal dust and vehicles. However, the necessary coal

The economic impact of emission peaking control policies and China's sustainable development

Directory of Open Access Journals (Sweden)

Yi Wang

2014-12-01

Full Text Available To achieve the goals of national sustainable development, the peaking control of CO2 emissions is pivotal, as well as other pollutants. In this paper, we build a Chinese inter-regional CGE model and simulate 13 policies and their combinations. By analyzing the energy consumptions, coal consumptions, relating emissions and their impacts on GDP, we found that with the structure adjustment policy, the proportion of coal in primary fossil fuels in 2030 will decrease from 53% to 48% and CO2 emissions will decrease by 11.3%–22.8% compared to the baseline scenario. With the energy intensity reduction policy, CO2 emissions will decrease by 33.3% in 2030 and 47.8% in 2050 than baseline scenario. Other pollutants will also be controlled as synergetic effects. In this study we also find that although the earlier the peaking time the better for emission amounts control, the economic costs can not be ignored. The GDP will decrease by 2.96%–8.23% under different scenarios. Therefore, integrated policy solutions are needed for realizing the peaks package and more targeted measures are required to achieve the peaks of other pollutants earlier.

Spontaneous formation of {1 1-bar 0 1} InGaN quantum wells on a (1 1 2-bar 2) GaN template and their electroluminescence characteristics

International Nuclear Information System (INIS)

Masui, Hisashi; Kamber, Derrick S; Brinkley, Stuart E; Wu, Feng; Baker, Troy J; Zhong, Hong; Iza, Michael; Speck, James S; Nakamura, Shuji; DenBaars, Steven P

2010-01-01

Discrete dies of the light-emitting diode (LED) fabricated on a (1 1 2-bar 2)-oriented GaN template exhibited electroluminescence peaked at 467 nm and optical output power was greater than 200 µW at 20 mA. The LED was found to have quantum well structure grown on spontaneously formed {1 1-bar 0 1} facets, confirmed via transmission electron microscopy. Polarization switching was observed in luminescence perpendicular to the device surface: the dominant polarization was parallel to [1-bar 1-bar 2 3]. The device structure was shown to be advantageous for photovoltaic cell applications by evaluating photo-induced current, although piezoelectric effects on photocurrent were not explicitly determined. The filling rate of band-edge states was estimated to be 0.025 eV per decade of current via low-temperature electroluminescence measurements

Crystal Phase Quantum Well Emission with Digital Control.

Science.gov (United States)

Assali, S; Lähnemann, J; Vu, T T T; Jöns, K D; Gagliano, L; Verheijen, M A; Akopian, N; Bakkers, E P A M; Haverkort, J E M

2017-10-11

One of the major challenges in the growth of quantum well and quantum dot heterostructures is the realization of atomically sharp interfaces. Nanowires provide a new opportunity to engineer the band structure as they facilitate the controlled switching of the crystal structure between the zinc-blende (ZB) and wurtzite (WZ) phases. Such a crystal phase switching results in the formation of crystal phase quantum wells (CPQWs) and quantum dots (CPQDs). For GaP CPQWs, the inherent electric fields due to the discontinuity of the spontaneous polarization at the WZ/ZB junctions lead to the confinement of both types of charge carriers at the opposite interfaces of the WZ/ZB/WZ structure. This confinement leads to a novel type of transition across a ZB flat plate barrier. Here, we show digital tuning of the visible emission of WZ/ZB/WZ CPQWs in a GaP nanowire by changing the thickness of the ZB barrier. The energy spacing between the sharp emission lines is uniform and is defined by the addition of single ZB monolayers. The controlled growth of identical quantum wells with atomically flat interfaces at predefined positions featuring digitally tunable discrete emission energies may provide a new route to further advance entangled photons in solid state quantum systems.

Liquid crystalline networks for electroluminescent displays

International Nuclear Information System (INIS)

Contoret, A.E.A.

2001-09-01

This work presents the first low molar mass organic electroluminescent (EL) material to form a nematic glass and then emit plane-polarised light from the vitrified state on application of an electric field. Photocrosslinkable molecules are also discussed which form insoluble films on illumination with ultra-violet light. This approach combines the ease of deposition of small molecules with the robustness and stability of polymers, allowing simple fabrication of multi-layer EL devices and photo-patterning. A range of conjugated low molar-mass molecules are considered, containing the anthracene, perylene and fluorene cores, with the aims of producing a general recipe for efficient EL, based on ordered, stable nematics at room temperature. Many physical properties are compared and molecular mechanics modeling is used to represent molecular geometries. An acrylate and several diene photo-polymerisable derivatives of the fluorenes undergo photo-crosslinking. Infrared and photoluminescence spectroscopy is used to examine crosslinking in detail and to optimise exposure conditions. The diene shows no significant degradation for an optimal exposure, but requires a high fluence of 100 Jcm -2 to form an insoluble film. A doped photo-alignment layer is used for the first time to obtain polarised El with ratio 11:1 and 80 cdm -2 brightness from the crosslinked diene. The insoluble crosslinked network allows spin coating of an electron transporting over-layer, resulting in increased brightness. Complex impedance spectroscopy and time of flight measurements confirm good material properties with complete depletion of the crosslinkable diene molecule and non-dispersive conduction. Finally, a novel deposition technique, pulsed laser deposition (PLD), is presented, as an alternative to spin coating or vapour deposition. Minimal degradation is observed for optimised deposition conditions and a PLD film is successfully demonstrated in an EL device. (author)

Emissions control of volatile organic compounds in petroleum industry; Controle de emissoes de compostos organicos volateis na industria do petroleo

Energy Technology Data Exchange (ETDEWEB)

Gutierres, Ricardo; Moreira, Andrea Cristina de Castro Araujo [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES). P e D de Energia e Desenvolvimento Sustentavel (PDEDS)

2004-07-01

Volatile organic compounds are among the most common pollutants emitted by refining processes. The sources of these emissions should be controlled for preserving the ambient air quality. This article outlines the main factors to be considered for defining an effective emissions control strategy and compares the major characteristics of the available control technologies. (author)

Emissions inventories and options for control SUMMARY REPORT

NARCIS (Netherlands)

Swart RJ; Amstel AR van; Born GJ van den; Kroeze C; MTV; LAE

1994-01-01

This report is the final summary report of the project "Social causes of the greenhouse effect ; emissions inventories and options for control", funded by the National Research Programme on Global Air Pollution and Climate Change (NRP) and the Environment Directorate of the Ministry of Housing,

Legal and planning framework for the control of noise emissions

International Nuclear Information System (INIS)

Trinick, M.

1992-01-01

An examination is offered of the statutory basis for the control of noise emissions. Principal pieces of legislation and some advisory notes have been produced within appendices. The paper briefly examines the controls in other EC countries before discussing the way in which planning controls relate to the jurisdiction of the court. (author)

Measuring and controlling greenhouse gas emissions

International Nuclear Information System (INIS)

Bourrier, Herve; LAFONT, Bruno; Fischer, Severin; Leonard, Damien; Tutenuit, Claire

2011-05-01

As providing a reporting of their greenhouse gas emissions has become mandatory for a large number of French companies, this publication proposes a methodology to perform an assessment or measurement, and a control of such emissions. In its first part, it explains why measurements are required: indication of concerned gases, international consensus to limit temperature rise, definition and chronology of the main steps adopted at the international level and which must be considered in the approach adopted by enterprises in this respect. It outlines the benefits of such a measurement for the enterprise in terms of competitiveness, personnel commitment, new markets and products, image, compliance with the law, operational and financial aspects, and so on. It identifies the various stakeholders to be informed: civil society, financial community, public authorities, clients and consumers, personnel, suppliers. It outlines the diversity and evolution of legal frameworks at the international level as well as at national levels. While evoking many examples of French companies (SNCF, EDF, Seche Environnement, RTE, Michelin, Arcelormittal, AREVA, Air France, EADS-Airbus, AXA, Veolia, and so on), the next part addresses how to measure emissions. It outlines the complexity of the methodological landscape with its various criteria, evokes the various existing standards, outlines the distinction between organisation-based, product-based and project-based approaches, and the distinction between direct and indirect emissions in relationship with the notion of scope. It comments the existence of sector-based methodologies and guidelines, and discusses some difficulties and methodological decisions. The third part proposes some lessons learned from the experience which could lead to a harmonisation of methodologies, proposes a synthesis of reporting approaches, outlines risks and opportunities related to communication

Photoluminescent (PL) or electroluminescent (EL) quantum dots for display, lighting, and photomedicine (Conference Presentation)

Science.gov (United States)

Dong, Yajie

2017-02-01

Quantum dots (QDs) have gone through a long journey before finding their ways into the display field. This talk will briefly touch on the history before trying to answer several key questions related to QDs applications in display: What are QDs? How are they made? What properties do they have and Why? How can these properties be used to improve color and efficiency of display, in either photoluminescence (PL) or electroluminescence (EL) mode? And what are the remaining challenges for QDs wide adoption in display industry? Lastly, some most recent progresses in our UCF lab at both PL and EL fronts will be highlighted. For PL, a cadmium-free perovskite-polymer composite films with exceptionally narrow emission green peaks (FWHM 20 nm) and good water and thermal stability will be reported. Together with red quantum dots or PFS/KSF phosphors as down-converters for blue LEDs, a white-light source with 95% Rec. 2020 color gamut was demonstrated [1]. For EL, red quantum dot light emitting devices (QLEDs) with record luminance of 165,000 Cd/m2 has been obtained at a current density of 1000 mA/cm2 with a low driving voltage of 5.8 V and CIE coordinates of (0.69, 0.31). [2] The potential of using these QLEDs for light sources for integrated sensing platform [3] or high efficiency, high color quality hybrid white OLED [4] will be discussed. [1] Y. N. Wang, J. He, H. Chen, J. S. Chen, R. D. Zhu, P. Ma, A. Towers, Y. Lin, A. J. Gesquiere, S. T. Wu, Y. J. Dong. Ultrastable, Highly Luminescent Organic-Inorganic Perovskite - Polymer Composite Films, Advanced Materials, accepted, (2016). [2] Y. J. Dong, J.M. Caruge, Z. Q. Zhou, C. Hamilton, Z. Popovic, J. Ho, M. Stevenson, G. Liu, V. Bulovic, M. Bawendi, P. T. Kazlas, S. Coe-Sullivan, and J. Steckel Ultra-bright, Highly Efficient, Low Roll-off Inverted Quantum-Dot Light Emitting Devices (QLEDs). SID Symp. Dig. Tech. Pap. 46, 270-273 (2015). [3] J. He, H. Chen, S. T. Wu, and Y. J. Dong, Integrated Sensing Platform Based on Quantum

New cyclometalated Iridium(III) beta-dicetone complex as phosphorescent dopant in Organic light emitting devices

Science.gov (United States)

Ivanov, P.; Petrova, P.; Stanimirov, S.; Tomova, R.

2017-01-01

A new Bis[4-(benzothiazolato-N,C2‧-2-yl)-N,N-dimethylaniline]Iridium(III) acetylacetonate (Me2N-bt) 2Ir(acac) was synthesized and identified by 1H NMR and elemental analysis. The application of the new compound as a dopant in the hole transporting layer (HTL) of Organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was N,N’-bis(3-methylphenyl)-N,N’-diphenylbenzidine (TPD), incorporated in Poly(N-vinylcarbazole) (PVK) matrix, EL - electroluminescent layer of Bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy)aluminum (BAlq) and ETL - electron-transporting layer of Tris-(8-hydroxyquinoline) aluminum (Alq3) or Bis[2-(2-benzothiazoly) phenolato]zinc (Zn(btz)2). We established that the electroluminescent spectra of OLEDs at different concentrations of the dopant were basically the sum of the greenish-blue emission of BAlq and yellowish-green emission of Ir complex. It was found that with increasing of the dopant concentration the relative electroluminescent intensity of Iridium complex emission increased and this of BAlq decreased and as a result the fine tuning of OLED color was observed.

Electroplex emission from a layer of a mixture of a europium complex and tris(8-quinolinolato) aluminum

Science.gov (United States)

Cao, Hong; Gao, Xicun; Huang, Chun-Hui

2000-07-01

With a europium complex, tris(α-thenoyltrifluoroacetonato) bis(triphenylphosphine oxide) europium (Eu(TTA) 3(TPPO) 2), as the light-emitting layer, N, N'-diphenyl- N, N'-di( m-tolyl)-benzidine (TPD) as the hole transport layer and tris(8-quinolinolato) aluminum (ALQ) as the electron transport layer, the triple-layer electroluminescent (EL) device emits red light characteristic of Eu 3+ emission. However, as the mixture of Eu(TTA) 3(TPPO) 2 and ALQ is co-evaporated as the light-emitting layer to form a bilayer EL device, a new wide-banded emission peaked at c. 640 nm was obtained. This emission is neither from ALQ nor from the europium complex. The photoluminescence (PL) of the thin film on quartz substrate evaporated from one mixed solid powder of Eu(TTA) 3(TPPO) 2 and ALQ is composed of distinct PL emissions of Eu(TTA) 3(TPPO) 2 and ALQ, denying an exciplex formation mechanism. It is impossible to form a host-guest system. We propose that the EL emission peaked at c. 640 nm is from an electroplex route: a transition between the lowest unoccupied molecular orbital (LUMO) of Eu(TTA) 3(TPPO) 2 and the highest occupied molecular orbital (HOMO) of ALQ.

A Techno-Economic Analysis of Emission Controls on Hydrocarbon Biofuel Production

Energy Technology Data Exchange (ETDEWEB)

Bhatt, Arpit; Zhang, Yimin; Davis, Ryan; Eberle, Annika; Heath, Garvin

2016-06-23

Biofuels have the potential to reduce our dependency on petroleum-derived transportation fuels and decrease greenhouse gas (GHG) emissions. Although the overall GHG emissions from biofuels are expected to be lower when compared to those of petroleum fuels, the process of converting biomass feedstocks into biofuels emits various air pollutants, which may be subject to federal air quality regulation or emission limits. While prior research has evaluated the technical and economic feasibility of biofuel technologies, gaps still exist in understanding the regulatory issues associated with the biorefineries and their economic implications on biofuel production costs (referred to as minimum fuel selling price (MFSP) in this study). The aim of our research is to evaluate the economic impact of implementing emission reduction technologies at biorefineries and estimate the cost effectiveness of two primary control technologies that may be required for air permitting purposes. We analyze a lignocellulosic sugars-to-hydrocarbon biofuel production pathway developed by the National Renewable Energy Laboratory (NREL) and implement air emission controls in Aspen Plus to evaluate how they affect the MFSP. Results from this analysis can help inform decisions about biorefinery siting and sizing, as well as mitigate the risks associated with air permitting.

Combustion Dynamics and Control for Ultra Low Emissions in Aircraft Gas-Turbine Engines

Science.gov (United States)

DeLaat, John C.

2011-01-01

Future aircraft engines must provide ultra-low emissions and high efficiency at low cost while maintaining the reliability and operability of present day engines. The demands for increased performance and decreased emissions have resulted in advanced combustor designs that are critically dependent on efficient fuel/air mixing and lean operation. However, all combustors, but most notably lean-burning low-emissions combustors, are susceptible to combustion instabilities. These instabilities are typically caused by the interaction of the fluctuating heat release of the combustion process with naturally occurring acoustic resonances. These interactions can produce large pressure oscillations within the combustor and can reduce component life and potentially lead to premature mechanical failures. Active Combustion Control which consists of feedback-based control of the fuel-air mixing process can provide an approach to achieving acceptable combustor dynamic behavior while minimizing emissions, and thus can provide flexibility during the combustor design process. The NASA Glenn Active Combustion Control Technology activity aims to demonstrate active control in a realistic environment relevant to aircraft engines by providing experiments tied to aircraft gas turbine combustors. The intent is to allow the technology maturity of active combustion control to advance to eventual demonstration in an engine environment. Work at NASA Glenn has shown that active combustion control, utilizing advanced algorithms working through high frequency fuel actuation, can effectively suppress instabilities in a combustor which emulates the instabilities found in an aircraft gas turbine engine. Current efforts are aimed at extending these active control technologies to advanced ultra-low-emissions combustors such as those employing multi-point lean direct injection.

Cost-Effective Reciprocating Engine Emissions Control and Monitoring for E&P Field and Gathering Engines

Energy Technology Data Exchange (ETDEWEB)

Keith Hohn; Sarah R. Nuss-Warren

2011-08-31

This final report describes a project intended to identify, develop, test, and commercialize emissions control and monitoring technologies that can be implemented by E&P operators to significantly lower their cost of environmental compliance and expedite project permitting. Technologies were installed and tested in controlled laboratory situations and then installed and tested on field engines based on the recommendations of an industry-based steering committee, analysis of installed horsepower, analysis of available emissions control and monitoring technologies, and review of technology and market gaps. The industry-recognized solution for lean-burn engines, a low-emissions-retrofit including increased airflow and pre-combustion chambers, was found to successfully control engine emissions of oxides of nitrogen (NO{sub X}) and carbon monoxide (CO). However, the standard non-selective catalytic reduction (NSCR) system recognized by the industry was found to be unable to consistently control both NO{sub X} and CO emissions. The standard NSCR system was observed to produce emissions levels that changed dramatically on a day-to-day or even hour-to-hour basis. Because difficulties with this system seemed to be the result of exhaust gas oxygen (EGO) sensors that produced identical output for very different exhaust gas conditions, models were developed to describe the behavior of the EGO sensor and an alternative, the universal exhaust gas oxygen (UEGO) sensor. Meanwhile, an integrated NSCR system using an advanced, signal-conditioned UEGO sensor was tested and found to control both NO{sub X} and CO emissions. In conjunction with this project, advanced monitoring technologies, such as Ion Sense, and improved sensors for emissions control, such as the AFM1000+ have been developed and commercialized.

Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

Directory of Open Access Journals (Sweden)

S.-T. Pham

2018-02-01

Full Text Available Magneto-electroluminescence (MEL effects are observed in single-layer organic light-emitting devices (OLEDs comprising only macrocyclic aromatic hydrocarbons (MAHs. The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6. The MEL ratio of the resulting OLED is 1%–2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (−1.5% to −2% in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

Magneto-electroluminescence effects in the single-layer organic light-emitting devices with macrocyclic aromatic hydrocarbons

Science.gov (United States)

Pham, S.-T.; Ikemoto, K.; Suzuki, K. Z.; Izumi, T.; Taka, H.; Kita, H.; Sato, S.; Isobe, H.; Mizukami, S.

2018-02-01

Magneto-electroluminescence (MEL) effects are observed in single-layer organic light-emitting devices (OLEDs) comprising only macrocyclic aromatic hydrocarbons (MAHs). The fluorescence devices were prepared using synthesized MAHs, namely, [n]cyclo-meta-phenylene ([n]CMP, n = 5, 6). The MEL ratio of the resulting OLED is 1%-2% in the spectral wavelength range of 400-500 nm, whereas it becomes negative (-1.5% to -2%) in the range from 650 to 700 nm. The possible physical origins of the sign change in the MEL are discussed. This wavelength-dependent sign change in the MEL ratio could be a unique function for future single-layer OLEDs capable of magnetic-field-induced color changes.

Pattern visual evoked potentials elicited by organic electroluminescence screen.

Science.gov (United States)

Matsumoto, Celso Soiti; Shinoda, Kei; Matsumoto, Harue; Funada, Hideaki; Sasaki, Kakeru; Minoda, Haruka; Iwata, Takeshi; Mizota, Atsushi

2014-01-01

To determine whether organic electroluminescence (OLED) screens can be used as visual stimulators to elicit pattern-reversal visual evoked potentials (p-VEPs). Checkerboard patterns were generated on a conventional cathode-ray tube (S710, Compaq Computer Co., USA) screen and on an OLED (17 inches, 320 × 230 mm, PVM-1741, Sony, Tokyo, Japan) screen. The time course of the luminance changes of each monitor was measured with a photodiode. The p-VEPs elicited by these two screens were recorded from 15 eyes of 9 healthy volunteers (22.0 ± 0.8 years). The OLED screen had a constant time delay from the onset of the trigger signal to the start of the luminescence change. The delay during the reversal phase from black to white for the pattern was 1.0 msec on the cathode-ray tube (CRT) screen and 0.5 msec on the OLED screen. No significant differences in the amplitudes of P100 and the implicit times of N75 and P100 were observed in the p-VEPs elicited by the CRT and the OLED screens. The OLED screen can be used as a visual stimulator to elicit p-VEPs; however the time delay and the specific properties in the luminance change must be taken into account.

Engine Tune-up Service. Unit 6: Emission Control Systems. Posttests. Automotive Mechanics Curriculum.

Science.gov (United States)

Morse, David T.; May, Theodore R.

This book of posttests is designed to accompany the Engine Tune-Up Service Student Guide for Unit 6, Emission Control Systems, available separately as CE 031 220. Focus of the posttests is inspecting, testing, and servicing emission control systems. One multiple choice posttest is provided that covers the seven performance objectives contained in…

Optical microcavities and enhanced electroluminescence from electroformed Al-Al{sub 2}O{sub 3}-Ag diodes

Energy Technology Data Exchange (ETDEWEB)

Hickmott, T. W. [Department of Physics, State University of New York at Albany, Albany, New York 12222 (United States)

2013-12-21

Electroluminescence (EL) and electron emission into vacuum (EM) occur when a non-destructive dielectric breakdown of Al-Al{sub 2}O{sub 3}-Ag diodes, electroforming, results in the development of a filamentary region in which current-voltage (I-V) characteristics exhibit voltage-controlled negative resistance. The temperature dependence of I-V curves, EM, and, particularly, EL of Al-Al{sub 2}O{sub 3}-Ag diodes with anodic Al{sub 2}O{sub 3} thicknesses between 12 nm and 30 nm, has been studied. Two filters, a long-pass (LP) filter with transmission of photons with energies less than 3.0 eV and a short-pass (SP) filter with photon transmission between 3.0 and 4.0 eV, have been used to characterize EL. The voltage threshold for EL with the LP filter, V{sub LP}, is ∼1.5 V. V{sub LP} is nearly independent of Al{sub 2}O{sub 3} thickness and of temperature and is 0.3–0.6 V less than the threshold voltage for EL for the SP filter, V{sub SP}. EL intensity is primarily between 1.8 and 3.0 eV when the bias voltage, V{sub S} ≲ 7 V. EL in the thinnest diodes is enhanced compared to EL in thicker diodes. For increasing V{sub S}, for diodes with the smallest Al{sub 2}O{sub 3} thicknesses, there is a maximum EL intensity, L{sub MX}, at a voltage, V{sub LMX}, followed by a decrease to a plateau. L{sub MX} and EL intensity at 4.0 V in the plateau region depend exponentially on Al{sub 2}O{sub 3} thickness. The ratio of L{sub MX} at 295 K for a diode with 12 nm of Al{sub 2}O{sub 3} to L{sub MX} for a diode with 25 nm of Al{sub 2}O{sub 3} is ∼140. The ratio of EL intensity with the LP filter to EL intensity with the SP filter, LP/SP, varies between ∼3 and ∼35; it depends on Al{sub 2}O{sub 3} thickness and V{sub S}. Enhanced EL is attributed to the increase of the spontaneous emission rate of a dipole in a non-resonant optical microcavity. EL photons interact with the Ag and Al films to create surface plasmon polaritons (SPPs) at the metal-Al{sub 2}O

40 CFR 91.113 - Requirement of certification-emission control information label and engine identification number.

Science.gov (United States)

2010-07-01

... control information label and engine identification number. 91.113 Section 91.113 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM... certification—emission control information label and engine identification number. (a) The engine manufacturer...

Zinc Cadmium Selenide Cladded Quantum Dot Based Electroluminescent and Nonvolatile Memory Devices

Science.gov (United States)

Al-Amody, Fuad H.

This dissertation presents electroluminescent (EL) and nonvolatile memory devices fabricated using pseudomorphic ZnCdSe-based cladded quantum dots (QDs). These dots were grown using our own in-school built novel reactor. The EL device was fabricated on a substrate of ITO (indium tin oxide) coated glass with the quantum dots sandwiched between anode and cathode contacts with a small barrier layer on top of the QDs. The importance of these cladded dots is to increase the quantum yield of device. This device is unique as they utilize quantum dots that are pseudomorphic (nearly lattice-matched core and the shell of the dot). In the case of floating quantum dot gate nonvolatile memory, cladded ZnCdSe quantum dots are deposited on single crystalline gate insulator (ZnMgS/ZnMgSe), which is grown using metal-organic chemical vapor deposition (MOCVD). The control gate dielectric layer of the nonvolatile memory is Si3N4 or SiO2 and is grown using plasma enhanced chemical vapor deposition (PECVD). The cladded dots are grown using an improved methodology of photo-assisted microwave plasma metal-organic chemical vapor deposition (PMP-MOCVD) enhanced reactor. The cladding composition of the core and shell of the dots was engineered by the help of ultraviolet light which changed the incorporation of zinc (and hence composition of ZnCdSe). This makes ZnxCd1--xSe-ZnyCd1--y Se QDs to have a low composition of zinc in the core than the cladding (x

Control of Atmospheric Emissions in the Wood Pulping Industry, Volume 3.

Science.gov (United States)

Hendrickson, E. R.; And Others

Volume 3 contains chapters 9 through 13 of the final report on the control of atmospheric emissions in the wood pulping industry. These chapters deal with the following topics: sampling and analytical techniques; on-going research related to reduction of emissions; research and development recommendations; current industry investment and operating…

Physical processes in thin-film electroluminescent structures based on ZnS:Mn showing self-organized patterns

International Nuclear Information System (INIS)

Zuccaro, S.; Raker, Th.; Niedernostheide, F.-J.; Kuhn, T.; Purwins, H.-G.

2003-01-01

Physical processes in thin ZnS:Mn films and their relation to the formation of dynamical patterns in the electroluminescence of AC driven films are investigated. The technique of photo-depolarization-spectroscopy is used to investigate defect states in these films and it is shown that specific features in the spectra correlate with the observed self-organized patterns. Furthermore, the time dependence of the dissipative current is measured at the same samples and compared with current waveforms obtained from numerical simulations of a drift-diffusion model. The results are used to discuss the origin of the self-organized processes in ZnS:Mn-films

Controlling fugitive dust emissions in material handling operations

Energy Technology Data Exchange (ETDEWEB)

Tooker, G E

1992-05-01

The primary mechanism of fugitive dust generation in bulk material handling transfer operations is by dispersion of dust in turbulent air induced to flow with falling or projected material streams. This paper returns to basic theories of particle dynamics and fluid mechanics to quantify the dust generating mechanism by rational analysis. Calculations involving fluid mechanisms are made easier by the availability of the personal computer and the many math manipulating programs. Rational analysis is much more cost effective when estimating collection air volumes to control fugitive emissions; especially in enclosed material handling transfers transporting large volumes of dusty material. Example calculations, using a typical enclosed conveyor-to-conveyor transfer operation are presented to illustrate and highlight the key parameters that determine the magnitude of induced air flow that must be controlled. The methods presented in this paper for estimating collection air volumes apply only enclosed material handling transfers, exhausted to a dust collector. Since some assistance to the control of dust emissions must be given by the material handling transfer chute design, a discussion of good transfer chute design practice is presented. 4 refs., 2 figs., 2 tabs.

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 1

Energy Technology Data Exchange (ETDEWEB)

DOE; ORNL; NREL; EMA; MECA

1999-08-15

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim data report summarizes results as of August, 1999, on the status of the test programs being conducted on three technologies: lean-NO{sub x} catalysts, diesel particulate filters and diesel oxidation catalysts.

Impact of emission control on regional air quality in the Pearl Delta River region, southern China

Science.gov (United States)

Wang, N.; Xuejiao, D.

2017-12-01

The Pearl River Delta (PRD) in China has been suffering from air quality issues and the government has implemented a series of strategies in controlling emissions. In an attempt to provide scientific support for improving air quality, the paper investigates the concerning past-to-present air quality data and assesses air quality resulting from emission control. Statistical data revealed that energy consumption doubled from 2004 to 20014 and vehicle usage increased significantly from 2006 to 2014. Due to the effect of control efforts, primary emission of SO2, NOx and PM2.5 decreased resulting in ambient concentrations of SO2, NO2 and PM10 decreased by 66%, 20% and 24%, respectively. However, O3 increased 19% because of the increase of VOC emission. A chemical transport model, the Community Multi-scale Air Quality, was employed to evaluate the responses of nitrate, ammonium, SOA, PM2.5 and O3 to changes in NOx, VOC and NH3 emissions. Three scenarios, a baseline scenario, a CAP scenario (control strength followed as past tendency), and a REF scenario (strict control referred to latest policy and plans), were conducted to investigate the responses and mechanisms. NOx controlling scenarios showed that NOx, nitrate and PM2.5 reduced by 1.8%, 0.7% and 0.2% under CAP and reduced by 7.2%, 1.8% and 0.3% under REF, respectively. The results indicated that reducing NOx emission caused the increase of atmospheric oxidizability, which might result in a compensation of PM2.5 due to the increase of nitrate or sulfate. NH3 controlling scenarios showed that nitrate was sensitive to NH3 emission in PRD, with nitrate decreased by 0 - 10.6% and 0 - 48% under CAP and REF, respectively. Since controlling NH3 emissions not only reduced ammonium but also significantly reduced nitrate, the implement of NH3 controlling strategy was highly suggested. The VOC scenarios revealed that though SOA was not the major component of PM2.5, controlling VOC emission might take effect in southwestern PRD

Strongly transverse-electric-polarized emission from deep ultraviolet AlGaN quantum well light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Reich, Christoph, E-mail: Christoph.Reich@tu-berlin.de; Guttmann, Martin; Wernicke, Tim; Mehnke, Frank; Kuhn, Christian [Institut für Festkörperphysik, Technische Universität Berlin, Hardenbergstr. 36, Berlin 10623 (Germany); Feneberg, Martin; Goldhahn, Rüdiger [Institut für Experimentelle Physik, Otto-von-Guericke-Universität, Universitätsplatz 2, Magdeburg 39106 (Germany); Rass, Jens; Kneissl, Michael [Institut für Festkörperphysik, Technische Universität Berlin, Hardenbergstr. 36, Berlin 10623 (Germany); Ferdinand-Braun-Institut, Leibniz-Institut für Höchstfrequenztechnik, Gustav-Kirchhoff-Str. 4, Berlin 12489 (Germany); Lapeyrade, Mickael; Einfeldt, Sven; Knauer, Arne; Kueller, Viola; Weyers, Markus [Ferdinand-Braun-Institut, Leibniz-Institut für Höchstfrequenztechnik, Gustav-Kirchhoff-Str. 4, Berlin 12489 (Germany)

2015-10-05

The optical polarization of emission from ultraviolet (UV) light emitting diodes (LEDs) based on (0001)-oriented Al{sub x}Ga{sub 1−x}N multiple quantum wells (MQWs) has been studied by simulations and electroluminescence measurements. With increasing aluminum mole fraction in the quantum well x, the in-plane intensity of transverse-electric (TE) polarized light decreases relative to that of the transverse-magnetic polarized light, attributed to a reordering of the valence bands in Al{sub x}Ga{sub 1−x}N. Using k ⋅ p theoretical model calculations, the AlGaN MQW active region design has been optimized, yielding increased TE polarization and thus higher extraction efficiency for bottom-emitting LEDs in the deep UV spectral range. Using (i) narrow quantum wells, (ii) barriers with high aluminum mole fractions, and (iii) compressive growth on patterned aluminum nitride sapphire templates, strongly TE-polarized emission was observed at wavelengths as short as 239 nm.

Emission characteristics of plastic syringes sterilized with ethylene oxide--a controlled study.

Science.gov (United States)

Chien, Yeh-Chung; Su, Po-Chi; Lee, Lien-Hsiung; Chen, Chang-Yuh

2009-11-01

This study examined the emission characteristics of ethylene oxide (EO)-sterilized syringes under various environmental conditions, aiming to develop control strategies to minimize worker exposure. Experiments were performed in a facility in which temperature, relative humidity (RH), and air change rate (ACR) were controlled. Analytical results indicate that the main effects of the four test variables on kinetic parameters were statistically significant (p Plastic content, temperature, RH, and ACR affected EO emissions. ACR is an achievable means of control; however, the aeration area/system should be isolated to ensure adequate ventilation is achieved.

Impacts of temporary traffic control measures on vehicular emissions during the Asian games in Guangzhou, China.

Science.gov (United States)

Yao, Zhiliang; Zhang, Yingzhi; Shen, Xianbao; Wang, Xintong; Wu, Ye; He, Kebin

2013-01-01

To guarantee good traffic and air quality during the 16th Asian Games in Guangzhou, China, the government carried out two traffic control Drills before the Games and adopted traffic control measures during the Games. Vehicle activities before and during the first and second Drills, and during the Games, were surveyed. Based on the data under investigation, the impacts of control measures on traffic volumes and driving characteristics were analyzed during the first and second Drills, and the Games. The emission reduction of traffic control measures was also evaluated during the three stages using the MOBILE-China model. The results show that there were significant effects of implementing temporary traffic control measures on transportation activity and vehicular emissions. During the first and second Drills, and the Games, the average traffic volumes in monitored roads decreased, and the average speed of vehicles increased significantly The co-effects of traffic flow reduction, traffic congestion improvement, and the banning of high-emitting vehicles helped to greatly reduce the estimated emissions from motor vehicles in Guangzhou during the first and second Drills, and the Games. Estimated vehicular emissions were reduced by 38-52% during the first Drill and 28-36% for the second Drill. During the Asian Games, vehicular emissions of carbon monoxide (CO), hydrocarbon (HC), oxides of nitrogen (NO), and particulate matter with an aerodynamic diameter vehicular emissions of CO, HC, NOx, and PM10. Motor vehicles have become the most prevalent source of emissions and subsequently air pollution within Chinese cities. Understanding the impacts that different control measures have on vehicular emissions is very important in order to be able to control vehicle emissions. The results of this study will be very helpful for the further control of vehicle emissions in Guangzhou in the future. In addition, the effects of temporary transportation control measures will provide

A novel fuzzy-logic control strategy minimizing N2O emissions.

Science.gov (United States)

Boiocchi, Riccardo; Gernaey, Krist V; Sin, Gürkan

2017-10-15

A novel control strategy for achieving low N 2 O emissions and low effluent NH 4 + concentration is here proposed. The control strategy uses the measurements of ammonium and nitrate concentrations in inlet and outlet of the aerobic zone of a wastewater treatment plant to calculate a ratio indicating the balance among the microbial groups. More specifically, the ratio will indicate if there is a complete nitrification. In case nitrification is not complete, the controller will adjust the aeration level of the plant in order to inhibit the production of N 2 O from AOB and HB denitrification. The controller was implemented using the fuzzy logic approach. It was comprehensively tested for different model structures and different sets of model parameters with regards to its ability of mitigating N 2 O emissions for future applications in real wastewater treatment plants. It is concluded that the control strategy is useful for those plants having AOB denitrification as the main N 2 O producing process. However, in treatment plants having incomplete NH 2 OH oxidation as the main N 2 O producing pathway, a cascade controller configuration adapting the oxygen supply to respect only the effluent ammonium concentration limits was found to be more effective to ensure low N 2 O emissions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Electroluminescent refrigeration by ultra-efficient GaAs light-emitting diodes

Science.gov (United States)

Patrick Xiao, T.; Chen, Kaifeng; Santhanam, Parthiban; Fan, Shanhui; Yablonovitch, Eli

2018-05-01

Electroluminescence—the conversion of electrons to photons in a light-emitting diode (LED)—can be used as a mechanism for refrigeration, provided that the LED has an exceptionally high quantum efficiency. We investigate the practical limits of present optoelectronic technology for cooling applications by optimizing a GaAs/GaInP double heterostructure LED. We develop a model of the design based on the physics of detailed balance and the methods of statistical ray optics, and predict an external luminescence efficiency of ηext = 97.7% at 263 K. To enhance the cooling coefficient of performance, we pair the refrigerated LED with a photovoltaic cell, which partially recovers the emitted optical energy as electricity. For applications near room temperature and moderate power densities (1.0-10 mW/cm2), we project that an electroluminescent refrigerator can operate with up to 1.7× the coefficient of performance of thermoelectric coolers with ZT = 1, using the material quality in existing GaAs devices. We also predict superior cooling efficiency for cryogenic applications relative to both thermoelectric and laser cooling. Large improvements to these results are possible with optoelectronic devices that asymptotically approach unity luminescence efficiency.

Simple synthesis, photophysics, and electroluminescent properties of poly[2,7-bis(4-tert-butylstyryl)fluorene-9,9-diyl-alt-alkane-.alpha.,.omega.-diyl

Czech Academy of Sciences Publication Activity Database

Mikroyannidis, J. A.; Barberis, V. P.; Výprachtický, Drahomír; Cimrová, Věra

2007-01-01

Roč. 45, č. 5 (2007), s. 809-821 ISSN 0887-624X R&D Projects: GA MŠk(CZ) 1M06031; GA AV ČR IAA4050409; GA ČR GA203/04/1372 Institutional research plan: CEZ:AV0Z40500505 Keywords : distyrylfluorene * electrochemical properties * electroluminescence Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.529, year: 2007

Electroplex emission from bilayer LED based on 1-phenyl-3-(dimethyl-amino) styryl-5-(p-(dimethylamino) phenyl) pyrazoline and 2,2'-(2,5-thiophenediyl) bis-(5-phenyl)-1,3,4-oxadiazole

International Nuclear Information System (INIS)

Zhang Zhiming; Li Guowen; Shen Jiacong; Ma Yuguang

2003-01-01

The photoluminescence (PL) and electroluminescence (EL) properties of a novel organic compound, 2,2'-(2,5-thiophenediyl) bis-(5-phenyl)-1,3,4-oxadiazole (TOXD), were studied as electron transporting material. The PL emission maximum peak is at 408 nm of TOXD in chloroform and is at 472 nm in solid film, respectively. The EL emission maximum peaks of the bilayer ITO/PDP/TOXD/Al LED located between emission maximum peaks of TOXD (470 nm) and PDP (500 nm) at lower driving voltage, 4.5-5.4 V, and shifted to 508 nm at 6.0 V and 518 nm at 7.0 V with increase of applied voltage. The new EL emission peak at 518 nm from the bilayer LED is ascribed to electroplex formation at the interface of TOXD and PDP film in bilayer LED under external electric field. The electroplex emission is close to the energy levels of PDP and TOXD

CONTROL OF MERCURY EMISSIONS FROM COAL-FIRED ELECTRIC UTILITY BOILERS: INTERIM REPORT

Science.gov (United States)

The report provides additional information on mercury (Hg) emissions control following the release of "Study of Hazardous Air Pollutant Emissions from Electric Utility Steam Generating Units--Final Report to Congress" in February 1998. Chapters 1-3 describe EPA's December 2000 de...

How light, temperature, and measurement and growth [CO2] interactively control isoprene emission in hybrid aspen.

Science.gov (United States)

Niinemets, Ülo; Sun, Zhihong

2015-02-01

Plant isoprene emissions have been modelled assuming independent controls by light, temperature and atmospheric [CO2]. However, the isoprene emission rate is ultimately controlled by the pool size of its immediate substrate, dimethylallyl diphosphate (DMADP), and isoprene synthase activity, implying that the environmental controls might interact. In addition, acclimation to growth [CO2] can shift the share of the control by DMADP pool size and isoprene synthase activity, and thereby alter the environmental sensitivity. Environmental controls of isoprene emission were studied in hybrid aspen (Populus tremula × Populus tremuloides) saplings acclimated either to ambient [CO2] of 380 μmol mol(-1) or elevated [CO2] of 780 μmol mol(-1). The data demonstrated strong interactive effects of environmental drivers and growth [CO2] on isoprene emissions. Light enhancement of isoprene emission was the greatest at intermediate temperatures and was greater in elevated-[CO2]-grown plants, indicating greater enhancement of the DMADP supply. The optimum temperature for isoprene emission was higher at lower light, suggesting activation of alternative DMADP sinks at higher light. In addition, [CO2] inhibition of isoprene emission was lost at a higher temperature with particularly strong effects in elevated-[CO2]-grown plants. Nevertheless, DMADP pool size was still predicted to more strongly control isoprene emission at higher temperatures in elevated-[CO2]-grown plants. We argue that interactive environmental controls and acclimation to growth [CO2] should be incorporated in future isoprene emission models at the level of DMADP pool size. © The Author 2014. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Voltage color tunable OLED with (Sm,Eu)-β-diketonate complex blend

Science.gov (United States)

Reyes, R.; Cremona, M.; Teotonio, E. E. S.; Brito, H. F.; Malta, O. L.

2004-09-01

Light emission from organic electroluminescent diodes (OLEDs) in which mixed samarium and europium β-diketonate complexes, [Sm 0.7Eu 0.3(TTA) 3(TPPO) 2], was used as the emitting layer is described. The electroluminescence spectra exhibit narrow peaks arising from 4f-intraconfigurational transitions of the Sm 3+ and Eu 3+ ions and a broad emission band attributed to the electrophosphorescence of the TTA ligand. The intensity ratio of the peaks determined by the bias voltage applied to the OLED, together with the ligand electrophosphorescence, allows to obtain a voltage-tunable color light source.

Improved luminescence properties of nanocrystalline silicon based electroluminescent device by annealing

International Nuclear Information System (INIS)

Sato, Keisuke; Hirakuri, Kenji

2006-01-01

We report an annealing effect on electrical and luminescence properties of a red electroluminescent device consisting of nanocrystalline silicon (nc-Si). The red luminescence was generated by flowing the forward current into the device at a low threshold direct current (DC) forward voltage with a rise of annealing temperature up to 500 deg. C. Moreover, the luminescence of the device annealed at 500 deg. C was more intense than that of the device annealed at 200 deg. C or less under the same forward current density, because of the injection of a large quantity of carriers to the radiative recombination centers at the nc-Si surface vicinity. These were attained by a low resistivity of indium tin oxide (ITO) electrode and good contact at the ITO electrode/luminous layer interface region by the annealing treatment. The above results indicated that the annealing treatment of the device is effective for the realization of high luminance due to the improvement in the injection efficiency of carriers to the radiative recombination centers

A photovoltaic module diagnostic setup for lock-in-thermography and lock-in electroluminescence imaging

DEFF Research Database (Denmark)

Parikh, Harsh; Spataru, Sergiu; Sera, Dezso

2018-01-01

Electroluminescence (EL) imaging and infrared (IRT) thermography techniques have become indispensable tools in recent years for health diagnostic of PV modules in solar industry application. Complementary to these imaging methods, lock-in techniques can effectively remove noise by periodically...... modulating the input signal and averaging it over a desired number of periods. We propose a combined lock-in EL and lock-in IRT diagnostic setup for accurate analysis of different types of faults occurring in a solar module. The setup is built around a Goldeye CL-033 high-speed SWIR camera, which can acquire...... experimental work on a (36/72) cell solar module using combined (EL) or (IRT) lock-in-thermography. The setup allows one to investigate the different technological problems that can occur when performing PV diagnostics in drone-based inspections....

Homogeneous Synthesis and Electroluminescence Device of Highly Luminescent CsPbBr3 Perovskite Nanocrystals.

Science.gov (United States)

Wei, Song; Yang, Yanchun; Kang, Xiaojiao; Wang, Lan; Huang, Lijian; Pan, Daocheng

2017-03-06

Highly luminescent CsPbBr 3 perovskite nanocrystals (PNCs) are homogeneously synthesized by mixing toluene solutions of PbBr 2 and cesium oleate at room temperature in open air. We found that PbBr 2 can be easily dissolved in nonpolar toluene in the presence of tetraoctylammonium bromide, which allows us to homogeneously prepare CsPbBr 3 perovskite quantum dots and prevents the use of harmful polar organic solvents, such as N,N-dimethylformamide, dimethyl sulfoxide, and N-methyl-2-pyrrolidone. Additionally, this method can be extended to synthesize highly luminescent CH 3 NH 3 PbBr 3 perovskite quantum dots. An electroluminescence device with a maximal luminance of 110 cd/m 2 has been fabricated by using high-quality CsPbBr 3 PNCs as the emitting layer.

Reduction in Greenhouse Gas Emissions Associated with Worm Control in Lambs

Directory of Open Access Journals (Sweden)

Drew G. Coulter

2013-04-01

Full Text Available There are currently little or no data on the role of endemic disease control in reducing greenhouse gas (GHG emissions from livestock. In the present study, we have used an Intergovernmental Panel on Climate Change (IPCC-compliant model to calculate GHG emissions from naturally grazing lambs under four different anthelmintic drug treatment regimes over a 5-year study period. Treatments were either “monthly” (NST, “strategic” (SPT, “targeted” (TST or based on “clinical signs” (MT. Commercial sheep farming practices were simulated, with lambs reaching a pre-selected target market weight (38 kg removed from the analysis as they would no longer contribute to the GHG budget of the flock. Results showed there was a significant treatment effect over all years, with lambs in the MT group consistently taking longer to reach market weight, and an extra 10% emission of CO2e per kg of weight gain over the other treatments. There were no significant differences between the other three treatment strategies (NST, SPT and TST in terms of production efficiency or cumulated GHG emissions over the experimental period. This study has shown that endemic disease control can contribute to a reduction in GHG emissions from animal agriculture and help reduce the carbon footprint of livestock farming.

Emissions control for sensitive areas

International Nuclear Information System (INIS)

Baud, Trevor

2011-01-01

Full text: The Gorgon project needs almost no introduction. Located off the north-west coast of Western Australia, it is one of the world's largest natural gas projects, set on the environmentally sensitive Barrow Island. To protect the island's unique habitats, stringent environmental conditions have been imposed in terms of air, noise and light emissions, making the emission control system critical to the project's viability. Luhr Filter, specialists in dust and fume control solutions, were chosen by KMH Environmental to supply an emission control system for a waste incinerator facility serving the LNG processing plant on Barrow Island. KMH's preference was for a 'one stop' supplier of the entire pollution control system. This included a heat exchanger which had the added benefit of a compact build to fit in the limited real estate. The solution put forward was tailored to the unique environmental requirements of the Gorgon project. It was very much about collaboration and innovation to achieve the requisite results. KMH were also keen to limit the number of sub-contractors they had to deal with, and Luhr offered them a turn-key plant for the gas cleaning, integrating design and supply of all the equipment. Among the environmental requirements was that all putrescible waste created on-site - from the accommodation camps during the construction and, eventually, production phases - had to be incinerated rather than sent to landfill. The flue gas from the incinerators had to be treated in order to meet world-class environmental standards for emission of particulate, acid gases, metals and dioxins. KMH designed an incinerator system with primary and secondary combustion chambers in modular units to minimise labour requirements on site. The dry absorption system integrates Luhr's unique technologies for heat exchangers, absorption reactors, utilisation of the absorbent and the baghouse style filters with reverse pulse bag cleaning

Electroplex emission from bilayer LED based on 1-phenyl-3-(dimethyl-amino) styryl-5-(p-(dimethylamino) phenyl) pyrazoline and 2,2'-(2,5-thiophenediyl) bis-(5-phenyl)-1,3,4-oxadiazole

Energy Technology Data Exchange (ETDEWEB)

Zhang Zhiming; Li Guowen; Shen Jiacong; Ma Yuguang

2003-12-20

The photoluminescence (PL) and electroluminescence (EL) properties of a novel organic compound, 2,2'-(2,5-thiophenediyl) bis-(5-phenyl)-1,3,4-oxadiazole (TOXD), were studied as electron transporting material. The PL emission maximum peak is at 408 nm of TOXD in chloroform and is at 472 nm in solid film, respectively. The EL emission maximum peaks of the bilayer ITO/PDP/TOXD/Al LED located between emission maximum peaks of TOXD (470 nm) and PDP (500 nm) at lower driving voltage, 4.5-5.4 V, and shifted to 508 nm at 6.0 V and 518 nm at 7.0 V with increase of applied voltage. The new EL emission peak at 518 nm from the bilayer LED is ascribed to electroplex formation at the interface of TOXD and PDP film in bilayer LED under external electric field. The electroplex emission is close to the energy levels of PDP and TOXD.

Long-lived exciplex formation and delayed exciton emission in bulk heterojunction blends of silole derivative and polyfluorene copolymer: the role of morphology on exciplex formation and charge separation.

Science.gov (United States)

Benson-Smith, Jessica J; Wilson, Joanne; Dyer-Smith, Clare; Mouri, Kazuhiro; Yamaguchi, Shigehiro; Murata, Hideyuki; Nelson, Jenny

2009-06-04

Long-lived exciplex emission is observed in blend films of poly[9,9-dioctylfluorene-co-N-(4-methoxy-phenyl)diphenylamine] (TFMO) and the soluble silole derivative 2,5-bis-(2,2-bipyridin-6-yl)-1,1-dimethyl-3,4-diphenylsilacyclopentadiene (PyPySPyPy). The exciplex is characterized by a long-lived (approximately 40-90 ns) component in both the photoluminescence and electroluminescence spectra, which is red-shifted relative to the emission of the pristine materials. In addition to exciplex emission, delayed fluorescence from the TFMO singlet state is observed and is attributed to exciton regeneration through the interfacial exciplex state. Comparing blend films made using chlorobenzene and p-xylene solvents, we find that exciplex lifetime and exciton regeneration in the blend film are sensitive to the choice of solvent and the resulting morphology of the blend film. The exciplex emissive lifetime can be correlated to changes in photoluminescence quenching and efficiency of light-emitting diodes.

The blue skies in Beijing during APEC 2014: A quantitative assessment of emission control efficiency and meteorological influence

Science.gov (United States)

Liu, Hongli; He, Jing; Guo, Jianping; Miao, Yucong; Yin, Jinfang; Wang, Yuan; Xu, Hui; Liu, Huan; Yan, Yan; Li, Yuan; Zhai, Panmao

2017-10-01

Most previous studies attributed the alleviation of aerosol pollution to either emission control measures or favorable meteorological conditions. However, our understanding of their quantitative contribution is far from complete. In this study, based on model simulation using the CMA (China Meteorological Administration) Unified Atmospheric Chemistry Environment for aerosols (CUACE/Aero), in combination with simultaneous ground-based hourly PM2.5 observations, we aim to quantify the relative contributions of the emission control measures and meteorology to the blue-skies seen in Beijing during the Asia-Pacific Economic Cooperation (APEC) summit held in November of 2014. A series of model simulations have been performed over Beijing-Tianjin-Hebei (BTH) region by implementing nine different emission control schemes. To investigate the relative contributions of the emission control measures and meteorology, the study period has been divided into five episodes. Overall, the CUACE/Aero model can reasonably well reproduce the temporal and spatial evolution of PM2.5 during APEC 2014, although the model performance varies by different time periods and regions of interest. Model results show the emission control measures on average reduced the PM2.5 concentration by 41.3% in urban areas of Beijing and 39.7% in Huairou district, respectively, indicating emission control plays a significant role for the blue skies observed. Among all the emission control measures under investigation, local emission control in Beijing contributed the largest to the reduction of PM2.5 concentrations with a reduction of 35.5% in urban area of Beijing and 34.8% in Huairou, in contrast with the vehicle emission control in Hebei that contributed the least with a reduction of less than 1%. The emission control efficiency in five episodes has been assessed quantitatively, which falls in the range of 36.2%-41.2% in urban area of Beijing and 34.9%-40.7% in Huairou, indicative of no significant episode

Multi-lateral emission trading: lessons from inter-state NOx control in the United States

International Nuclear Information System (INIS)

Farrell, A.

2001-01-01

Marketable emission permit mechanisms are increasingly proposed as efficient means of managing environmental pollution problems such as greenhouse gas emissions. Existing examples of emissions trading in the literature have so far been limited to domestic efforts put in place through the action of a national legislature, which has no parallel in international politics. This paper examines two efforts to establish multi-lateral emissions trading for nitrogen oxides among various states with the US. One, the Ozone Transport Commission's NO x Budget program is a success. The other, the Ozone Transport Assessment Group and the federal government's subsequent NO x SIP Call has not resulted in a multi-lateral emissions control program, let alone an efficient, market-based one. Due to the relative similarities of the states (compared to highly heterogeneous nations of the world) these are ''best case'' examples, and explaining the vast differences in outcomes will help explain the potential and the challenges in developing an international emission trading program to control greenhouse gas emissions. (author)

Shipping emission forecasts and cost-benefit analysis of China ports and key regions' control.

Science.gov (United States)

Liu, Huan; Meng, Zhi-Hang; Shang, Yi; Lv, Zhao-Feng; Jin, Xin-Xin; Fu, Ming-Liang; He, Ke-Bin

2018-05-01

China established Domestic Emission Control Area (DECA) for sulphur since 2015 to constrain the increasing shipping emissions. However, future DECA policy-makings are not supported due to a lack of quantitive evaluations. To investigate the effects of current and possible Chinese DECAs policies, a model is presented for the forecast of shipping emissions and evaluation of potential costs and benefits of an DECA policy package set in 2020. It includes a port-level and regional-level projection accounting for shipping trade volume growth, share of ship types, and fuel consumption. The results show that without control measures, both SO 2 and particulate matter (PM) emissions are expected to increase by 15.3-61.2% in Jing-Jin-Ji, the Yangtze River Delta, and the Pearl River Delta from 2013 to 2020. However, most emissions can be reduced annually by the establishment of a DECA that depends on the size of the control area and the fuel sulphur content limit. Costs range from 0.667 to 1.561 billion dollars (control regional shipping emissions) based on current fuel price. A social cost method shows the regional control scenarios benefit-cost ratios vary from 4.3 to 5.1 with large uncertainty. Chemical transportation model combined with health model method is used to get the monetary health benefits and then compared with the results from social cost method. This study suggests that Chinese DECAs will reduce the projected emissions at a favorable benefit-cost ratio, and furthermore proposes policy combinations that provide high cost-effective benefits as a reference for future policy-making. Crown Copyright © 2018. Published by Elsevier Ltd. All rights reserved.

Synthesis of Carbon Dots with Multiple Color Emission by Controlled Graphitization and Surface Functionalization.

Science.gov (United States)

Miao, Xiang; Qu, Dan; Yang, Dongxue; Nie, Bing; Zhao, Yikang; Fan, Hongyou; Sun, Zaicheng

2018-01-01

Multiple-color-emissive carbon dots (CDots) have potential applications in various fields such as bioimaging, light-emitting devices, and photocatalysis. The majority of the current CDots to date exhibit excitation-wavelength-dependent emissions with their maximum emission limited at the blue-light region. Here, a synthesis of multiple-color-emission CDots by controlled graphitization and surface function is reported. The CDots are synthesized through controlled thermal pyrolysis of citric acid and urea. By regulating the thermal-pyrolysis temperature and ratio of reactants, the maximum emission of the resulting CDots gradually shifts from blue to red light, covering the entire light spectrum. Specifically, the emission position of the CDots can be tuned from 430 to 630 nm through controlling the extent of graphitization and the amount of surface functional groups, COOH. The relative photoluminescence quantum yields of the CDots with blue, green, and red emission reach up to 52.6%, 35.1%, and 12.9%, respectively. Furthermore, it is demonstrated that the CDots can be uniformly dispersed into epoxy resins and be fabricated as transparent CDots/epoxy composites for multiple-color- and white-light-emitting devices. This research opens a door for developing low-cost CDots as alternative phosphors for light-emitting devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cost-Effective Reciprocating Engine Emissions Control and Monitoring for E&P Field and Gathering Engines

Energy Technology Data Exchange (ETDEWEB)

Kirby S. Chapman; Sarah R. Nuss-Warren

2007-02-01

The objective of this project is to identify, develop, test, and commercialize emissions control and monitoring technologies that can be implemented by exploration and production (E&P) operators to significantly lower the cost of environmental compliance and expedite project permitting. The project team takes considerable advantage of the emissions control research and development efforts and practices that have been underway in the gas pipeline industry for the last 12 years. These efforts and practices are expected to closely interface with the E&P industry to develop cost-effective options that apply to widely-used field and gathering engines, and which can be readily commercialized. The project is separated into two phases. Phase 1 work establishes an E&P industry liaison group, develops a frequency distribution of installed E&P field engines, and identifies and assesses commercially available and emerging engine emissions control and monitoring technologies. Current and expected E&P engine emissions and monitoring requirements are reviewed, and priority technologies are identified for further development. The identified promising technologies are tested on a laboratory engine to confirm their generic viability. In addition, a full-scale field test of prototype emissions controls will be conducted on at least ten representative field engine models with challenging emissions profiles. Emissions monitoring systems that are integrated with existing controls packages will be developed. Technology transfer/commercialization is expected to be implemented through compressor fleet leasing operators, engine component suppliers, the industry liaison group, and the Petroleum Technology Transfer Council. This topical report discusses work completed during Phase 1 of the project Cost Effective Reciprocating Engine Emissions Control and Monitoring for E&P Field and Gathering Engines. In this report information, data, and results are compiled and summarized from quarterly

Venturi/Vortex Scrubber Technology for Controlling/Recycling Chromium Electroplating Emissions

National Research Council Canada - National Science Library

Hay, K

1999-01-01

...) above the plating tank. Venturi/Vortex Scrubber Technology (VVST) was designed to control chromium electroplating emissions by collecting the gas bubbles before they burst at the solution's surface...

Carbon emissions control strategies

International Nuclear Information System (INIS)

Chandler, W.U.

1990-01-01

This study was undertaken to address a fundamental issue: the cost of slowing climate change. Experts in eight nations were asked to evaluate, using the best economic models available, the prospects for reducing fossil fuel-based carbon emissions in their respective nations. The nations selected as case studies include: the Soviet Union, Poland, the United States, Japan, Hungary, France, the United Kingdom, and Canada. As important contributors to the greenhouse effect, these industrialized nations must find ways to substantially reduce their emissions. This is especially critical given that developing nations' emissions are expected to rise in the coming decades in the search for economic development. Ten papers have been processed separately for inclusion in the appropriate data bases

High-performance alternating current field-induced chromatic-stable white polymer electroluminescent devices employing a down-conversion layer

Energy Technology Data Exchange (ETDEWEB)

Xia, Yingdong; Chen, Yonghua; Smith, Gregory M. [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Sun, Hengda; Yang, Dezhi [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Nie, Wanyi; Li, Yuan; Huang, Wenxiao [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States); Ma, Dongge [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Carroll, David L., E-mail: carroldl@wfu.edu [Center for Nanotechnology and Molecular Materials, Department of Physics, Wake Forest University, Winston-Salem, NC 27105 (United States)

2015-05-15

In this work, a high-performance alternating current (AC) filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated by combining a fluorophor Poly(9,9-dioctylfluorene) (PFO)-based blue device with a yellow down-conversion layer (YAG:Ce). A maximum luminance of this down-conversion FIPEL device achieves 3230 cd m{sup −2}, which is 1.41 times higher than the device without the down-conversion layer. A maximum current efficiency and power efficiency of the down-conversion WFIPEL device reach 19.7 cd A{sup −1} at 3050 cd m{sup −2} and 5.37 lm W{sup −1} at 2310 cd m{sup −2} respectively. To the best of our knowledge, the power efficiency is one of the highest reports for the WFIPEL up to now. Moreover, Commison Internationale de L’Eclairage (CIE) coordinates of (0.28, 0.30) is obtained by adjusting the thickness of the down-conversion layer to 30 μm and it is kept stable over the entire AC-driven voltage range. We believe that this AC-driven, down-conversion, WFIPEL device may offer an easy way towards future flat and flexible lighting sources. - Highlights: • A high-performance AC filed-induced chromatic-stable white polymer electroluminescence (WFIPEL) device was fabricated. • A maximum luminance, current efficiency, and power efficiency achieves 3230 cd m{sup −2}, 19.7 cd A{sup −1}, and 5.37 lm W{sup −1}, respectively. • The power efficiency is one of the highest reports for the WFIPEL up to now. • The EL spectrum kept very stable over the entire AC-driven voltage range.

Technology for controlling emissions from power plants fired with fossil fuel

Energy Technology Data Exchange (ETDEWEB)

Slack, A V

1981-04-01

Emission control technologies for fossil-fuel-fired power plants are examined. Acid rain, impaired visibility, and health effects of respirable particulates have combined to raise concerns from the local to the regional level. This report discusses advantages, disadvantages, and costs of technologies associated with emissions of sulfur oxides, nitrogen oxides, and particulate matter. Coal, oil and natural gas fuels are discussed. 7 refs.

Investigation of CaTiO3:Pr3+ thin films deposited by radiofrequency reactive magnetron sputtering for electroluminescence application

International Nuclear Information System (INIS)

Sarakha, L; Bousquet, A; Tomasella, E; Boutinaud, P; Mahiou, R

2010-01-01

In this report we successfully deposited thin films of CaTiO 3 :Pr 3+ by radiofrequency magnetron sputtering. The films were studied and we tried to understand the evolution of their optical and electrical properties. We noticed that the annealing temperature and the deposition pressures have an important influence on these properties. Thin films with good optical and electrical properties have been obtained. These films are transparent and are characterized by an intense red photoluminescence and a low fixed charge density. They are well dedicated for electroluminescence purposes.

Control of Several Emissions during Olive Pomace Thermal Degradation

Directory of Open Access Journals (Sweden)

Teresa Miranda

2014-10-01

Full Text Available Biomass plays an important role as an energy source, being an interesting alternative to fossil fuels due to its environment-friendly and sustainable characteristics. However, due to the exposure of customers to emissions during biomass heating, evolved pollutants should be taken into account and controlled. Changing raw materials or mixing them with another less pollutant biomass could be a suitable step to reduce pollution. This work studied the thermal behaviour of olive pomace, pyrenean oak and their blends under combustion using thermogravimetric analysis. It was possible to monitor the emissions released during the process by coupling mass spectrometry analysis. The experiments were carried out under non-isothermal conditions at the temperature range 25–750 °C and a heating rate of 20 °C·min−1. The following species were analysed: aromatic compounds (benzene and toluene, sulphur emissions (sulphur dioxide, 1,4-dioxin, hydrochloric acid, carbon dioxide and nitrogen oxides. The results indicated that pollutants were mainly evolved in two different stages, which are related to the thermal degradation steps. Thus, depending on the pollutant and raw material composition, different emission profiles were observed. Furthermore, intensity of the emission profiles was related, in some cases, to the composition of the precursor.

Intelligent emissions controller for substance injection in the post-primary combustion zone of fossil-fired boilers

Science.gov (United States)

Reifman, Jaques; Feldman, Earl E.; Wei, Thomas Y. C.; Glickert, Roger W.

2003-01-01

The control of emissions from fossil-fired boilers wherein an injection of substances above the primary combustion zone employs multi-layer feedforward artificial neural networks for modeling static nonlinear relationships between the distribution of injected substances into the upper region of the furnace and the emissions exiting the furnace. Multivariable nonlinear constrained optimization algorithms use the mathematical expressions from the artificial neural networks to provide the optimal substance distribution that minimizes emission levels for a given total substance injection rate. Based upon the optimal operating conditions from the optimization algorithms, the incremental substance cost per unit of emissions reduction, and the open-market price per unit of emissions reduction, the intelligent emissions controller allows for the determination of whether it is more cost-effective to achieve additional increments in emission reduction through the injection of additional substance or through the purchase of emission credits on the open market. This is of particular interest to fossil-fired electrical power plant operators. The intelligent emission controller is particularly adapted for determining the economical control of such pollutants as oxides of nitrogen (NO.sub.x) and carbon monoxide (CO) emitted by fossil-fired boilers by the selective introduction of multiple inputs of substances (such as natural gas, ammonia, oil, water-oil emulsion, coal-water slurry and/or urea, and combinations of these substances) above the primary combustion zone of fossil-fired boilers.

Two-band superlinear electroluminescence in GaSb based nanoheterostructures with AlSb/InAs.sub.1-x./sub.Sb.sub.x./sub./AlSb deep quantum well

Czech Academy of Sciences Publication Activity Database

Mikhailova, M. P.; Ivanov, E.V.; Danilov, L.V.; Petukhov, A.A.; Kalinina, K.V.; Slobozhanyuk, S.I.; Zegrya, G.G.; Stoyanov, N. D.; Yakovlev, Yu. P.; Hospodková, Alice; Pangrác, Jiří; Oswald, Jiří; Zíková, Markéta; Hulicius, Eduard

2014-01-01

Roč. 115, č. 22 (2014), "223102-1"-"223102-5" ISSN 0021-8979 R&D Projects: GA ČR GA13-15286S Institutional support: RVO:68378271 Keywords : MOVPE * GaSb * InAs * electroluminescence * quantum well Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.183, year: 2014

Pattern Visual Evoked Potentials Elicited by Organic Electroluminescence Screen

Directory of Open Access Journals (Sweden)

Celso Soiti Matsumoto

2014-01-01

Full Text Available Purpose. To determine whether organic electroluminescence (OLED screens can be used as visual stimulators to elicit pattern-reversal visual evoked potentials (p-VEPs. Method. Checkerboard patterns were generated on a conventional cathode-ray tube (S710, Compaq Computer Co., USA screen and on an OLED (17 inches, 320 × 230 mm, PVM-1741, Sony, Tokyo, Japan screen. The time course of the luminance changes of each monitor was measured with a photodiode. The p-VEPs elicited by these two screens were recorded from 15 eyes of 9 healthy volunteers (22.0 ± 0.8 years. Results. The OLED screen had a constant time delay from the onset of the trigger signal to the start of the luminescence change. The delay during the reversal phase from black to white for the pattern was 1.0 msec on the cathode-ray tube (CRT screen and 0.5 msec on the OLED screen. No significant differences in the amplitudes of P100 and the implicit times of N75 and P100 were observed in the p-VEPs elicited by the CRT and the OLED screens. Conclusion. The OLED screen can be used as a visual stimulator to elicit p-VEPs; however the time delay and the specific properties in the luminance change must be taken into account.

Enhanced Electroluminescence from Silicon Quantum Dots Embedded in Silicon Nitride Thin Films Coupled with Gold Nanoparticles in Light Emitting Devices

Directory of Open Access Journals (Sweden)

Ana Luz Muñoz-Rosas

2018-03-01

Full Text Available Nowadays, the use of plasmonic metal layers to improve the photonic emission characteristics of several semiconductor quantum dots is a booming tool. In this work, we report the use of silicon quantum dots (SiQDs embedded in a silicon nitride thin film coupled with an ultra-thin gold film (AuNPs to fabricate light emitting devices. We used the remote plasma enhanced chemical vapor deposition technique (RPECVD in order to grow two types of silicon nitride thin films. One with an almost stoichiometric composition, acting as non-radiative spacer; the other one, with a silicon excess in its chemical composition, which causes the formation of silicon quantum dots imbibed in the silicon nitride thin film. The ultra-thin gold film was deposited by the direct current (DC-sputtering technique, and an aluminum doped zinc oxide thin film (AZO which was deposited by means of ultrasonic spray pyrolysis, plays the role of the ohmic metal-like electrode. We found that there is a maximum electroluminescence (EL enhancement when the appropriate AuNPs-spacer-SiQDs configuration is used. This EL is achieved at a moderate turn-on voltage of 11 V, and the EL enhancement is around four times bigger than the photoluminescence (PL enhancement of the same AuNPs-spacer-SiQDs configuration. From our experimental results, we surmise that EL enhancement may indeed be due to a plasmonic coupling. This kind of silicon-based LEDs has the potential for technology transfer.

Effect of automatic control technologies on emission reduction in small-scale combustion

Energy Technology Data Exchange (ETDEWEB)

Ruusunen, M. [Control Engineering Laboratory, University of Oulu (Finland)

2007-07-01

Automatic control can be regarded as a primary measure for preventing combustion emissions. In this view, the control technology covers broadly the control methods, sensors and actuators for monitoring and controlling combustion. In addition to direct control of combustion process, it can also give tools for condition monitoring and optimisation of total heat consumption by system integration thus reducing the need for excess conversion of energy. Automatic control has already shown its potential in small-scale combustion. The potential, but still unrealised advantages of automatic control in this scale are the adaptation to changes in combustion conditions (fuel, environment, device, user) and the continuous optimisation of the air/fuel ratio. Modem control technology also covers combustion condition monitoring, diagnostics, and the higher level optimisation of the energy consumption with system integration. In theory, these primary measures maximise the overall efficiency, enabling a significant reduction in fuel consumption and thus total emissions per small-scale combustion unit, specifically at the annual level.

Post combustion methods for control of NOx emission

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, H S; Curran, L M; Slack, A V; Ando, J; Oxley, J H

1980-01-01

Review of stack gas treatment methods for the control of NOx emissions. Particular emphasis is placed on status of development and factors affecting the performance of the processes. Catalytic, noncatalytic, and scrubbing processes are compared on a uniform engineering basis. Most of the active process development work is taking place in Japan. The three leading stack gas treatment techniques for NOx control are catalytic reduction with ammonia, noncatalytic reduction with ammonia, and direct scrubbing of NO with simultaneous absorption of SO2. The wet processes are much less developed than the dry processes.

Effect of solvent-controlled aggregation on the intrinsic emission properties of PAMAM dendrimers

International Nuclear Information System (INIS)

Jasmine, Maria J.; Kavitha, Manniledam; Prasad, Edamana

2009-01-01

Solvent-induced aggregation and its effect on the intrinsic emission properties of amine, hydroxy and carboxylate terminated, poly(amidoamine) (PAMAM) dendrimers have been investigated in glycerol, ethylene glycol, methanol, ethylene diamine and water. Altering the solvent medium induces remarkable changes in the intrinsic emission properties of the PAMAM dendrimers at identical concentration. Upon excitation at 370 nm, amine terminated PAMAM dendrimer exhibits an intense emission at 470 nm in glycerol, ethylene glycol as well as glycerol-water mixtures. Conversely, weak luminescence is observed for hydroxy and carboxylate terminated PAMAM dendrimers in the same solvent systems. When the solvent is changed to ethylene diamine, hydroxy terminated PAMAM exhibits intense blue emission at 425 nm. While the emission intensity is varied when the solvent milieu is changed, excited state lifetime values of PAMAM dendrimers remain independent of the solvent used. UV-visible absorption and dynamic light scattering (DLS) experiments confirm the formation of solvent-controlled dendrimer aggregates in the systems. Comparison of the fluorescence and DLS data reveals that the size distribution of the dendrimer aggregates in each solvent system is distinct, which control the intrinsic emission intensity from PAMAM dendrimers. The experimental results suggest that intrinsic emission intensity from PAMAM dendrimers can be regulated by proper selection of solvents at neutral conditions and room temperature

Engine Tune-up Service. Unit 6: Emission Control Systems. Student Guide. Automotive Mechanics Curriculum.

Science.gov (United States)

Bacon, E. Miles

This student guide is for Unit 6, Emission Control Systems, in the Engine Tune-Up Service portion of the Automotive Mechanics Curriculum. It deals with inspecting, testing, and servicing an emission control system. A companion review exercise book and posttests are available separately as CE 031 221-222. An introduction tells how this unit fits…

An optimal control model for reducing and trading of carbon emissions

Science.gov (United States)

Guo, Huaying; Liang, Jin

2016-03-01

A stochastic optimal control model of reducing and trading for carbon emissions is established in this paper. With considerations of reducing the carbon emission growth and the price of the allowances in the market, an optimal policy is searched to have the minimum total costs to achieve the agreement of emission reduction targets. The model turns to a two-dimension HJB equation problem. By the methods of reducing dimension and Cole-Hopf transformation, a semi-closed form solution of the corresponding HJB problem under some assumptions is obtained. For more general cases, the numerical calculations, analysis and comparisons are presented.

New cyclometalated iridium(III) complex as a phosphorescent dopant in organic light emitting devices

Science.gov (United States)

Ivanov, P.; Tomova, R.; Petrova, P.; Stanimirov, S.; Petkov, I.

2014-05-01

A new cyclometalated iridium (III) bis[2-(4-chlorophenyl)benzothiazolato-N,C2]-acetylacetonate, (Cl-bt)2Ir(acac), was synthesized and identified by 1H NMR and elemental analysis. The application was studied of the new compound as a dopant in the hole transporting layer (HTL) of the following organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was 4,4'-bis(9H-carbazol-9-yl)biphenyl (CBP) or N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD), incorporated in a poly(N-vinylcarbazole) (PVK) matrix; EL was an electroluminescent layer of bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy) aluminum (BAlq); and ETL was an electron-transporting layer of bis[2-(2-benzothiazoly) phenolato]zinc(II) (Zn(btz)2). We established that the electroluminescence spectra of the OLEDs at different dopant concentrations were basically the sum of the greenish-blue emission of BAlq and the yellowish-green emission of the Ir complex. It was also found that increasing the dopant concentration resulted in an increase in the relative electroluminescent intensity of the Ir complex emission, while that of BAlq decreased, thus a fine tuning of the OLED color was observed.