WorldWideScience

Sample records for electrified transportation preprint

  1. Optimal Operation of Interdependent Power Systems and Electrified Transportation Networks

    Directory of Open Access Journals (Sweden)

    M. Hadi Amini

    2018-01-01

    Full Text Available Electrified transportation and power systems are mutually coupled networks. In this paper, a novel framework is developed for interdependent power and transportation networks. Our approach constitutes solving an iterative least cost vehicle routing process, which utilizes the communication of electrified vehicles (EVs with competing charging stations, to exchange data such as electricity price, energy demand, and time of arrival. The EV routing problem is solved to minimize the total cost of travel using the Dijkstra algorithm with the input from EVs battery management system, electricity price from charging stations, powertrain component efficiencies and transportation network traffic conditions. Through the bidirectional communication of EVs with competing charging stations, EVs’ charging demand estimation is done much more accurately. Then the optimal power flow problem is solved for the power system, to find the locational marginal price at load buses where charging stations are connected. Finally, the electricity prices were communicated from the charging stations to the EVs, and the loop is closed. Locational electricity price acts as the shared parameter between the two optimization problems, i.e., optimal power flow and optimal routing problem. Electricity price depends on the power demand, which is affected by the charging of EVs. On the other hand, location of EV charging stations and their different pricing strategies might affect the routing decisions of the EVs. Our novel approach that combines the electrified transportation with power system operation, holds tremendous potential for solving electrified transportation issues and reducing energy costs. The effectiveness of the proposed approach is demonstrated using Shanghai transportation network and IEEE 9-bus test system. The results verify the cost-savings for both power system and transportation networks.

  2. THE CALCULATION OF THE ENERGY RECOVERY ELECTRIFIED URBAN TRANSPORT DURING THE INSTALLATION DRIVE FOR TRACTION SUBSTATION

    Directory of Open Access Journals (Sweden)

    A. A. Sulim

    2014-01-01

    Full Text Available At present a great attention is paid to increasing of energy efficiency at operated electrified urban transport. Perspective direction for increasing energy efficiency at that type of transport is the application of regenerative braking. For additional increasing of energy efficiency there were suggested the use of capacitive drive on tires of traction substation. One of the main task is the analysis of energy recovery application  with drive and without it.These analysis demonstrated that the calculation algorithms don’t allow in the full volume to carry out calculations of amount and cost of energy recovery without drive and with it. That is why we see the current interest to this topic. The purpose of work is to create methods of algorithms calculation for definite amount and cost of consumed, redundant and recovery energy of electrified urban transport due to definite regime of motion on wayside. There is algorithm developed, which allow to calculate amount and cost of consumed, redundant and recovery energy of electrified urban transport on wayside during the installation capacitive drive at traction substation. On the basis of developed algorithm for the definite regime of wagon motion of subway there were fulfilled the example of energy recovery amount and its cost calculation, among them with limited energy intensity drive, when there are 4 trains on wayside simultaneously.

  3. MEASUREMENT AND ANALYSIS OF TRANSMISSION LOSSES IN THE SUPPLY SYSTEM OF ELECTRIFIED TRANSPORT

    Directory of Open Access Journals (Sweden)

    Mikołaj Bartłomiejczyk

    2016-11-01

    Full Text Available The issue of electric energy saving in public transport is currently becoming a key area of interest, a fact connected with both an increase in society’s environmental awareness and a rise in the prices of fuel and electricity. Electricity can be saved by reducing transmission losses in the supply system. The article presents a method of measurement and analysis of transmission losses in the supply system of electrified public transport on the example of trolleybus transport in Gdynia and Lublin in Poland.

  4. Fleet view of electrified transportation reveals smaller potential to reduce GHG emissions

    International Nuclear Information System (INIS)

    Meinrenken, Christoph J.; Lackner, Klaus S.

    2015-01-01

    reductions achievable from electrified transportation are smaller than previously considered (e.g., 55% reduction instead of 80%; scenario-dependent), even when assuming largely decarbonized grid-electricity. Optimal battery range that achieves lowest GHG for partially electrified fleets is different for plug-in hybrids versus pure electrics and furthermore varies strongly (∼35 to ∼200 km) with the predominant carbon-intensity of the grid

  5. Benefits of flexibility from smart electrified transportation and heating in the future UK electricity system

    International Nuclear Information System (INIS)

    Teng, Fei; Aunedi, Marko; Strbac, Goran

    2016-01-01

    Highlights: • The economic and environmental benefits of smart EVs/HPs are quantified. • This paper implements an advanced stochastic analytical framework. • Operating patterns and potential flexibility of EVs/HPs are sourced from UK trials. • A comprehensive set of case studies across UK future scenarios are carried out. - Abstract: This paper presents an advanced stochastic analytical framework to quantify the benefits of smart electric vehicles (EVs) and heat pumps (HPs) on the carbon emission and the integration cost of renewable energy sources (RES) in the future UK electricity system. The typical operating patterns of EVs/HPs as well as the potential flexibility to perform demand shifting and frequency response are sourced from recent UK trials. A comprehensive range of case studies across several future UK scenarios suggest that smart EVs/HPs could deliver measurable carbon reductions by enabling a more efficient operation of the electricity system, while at the same time making the integration of electrified transport and heating demand significantly less carbon intensive. The second set of case studies establish that smart EVs/HPs have significant potential to support cost-efficient RES integration by reducing: (a) RES balancing cost, (b) cost of required back-up generation capacity, and (c) cost of additional low-carbon capacity required to offset lower fuel efficiency and curtailed RES output while achieving the same emission target. Frequency response provision from EVs/HPs could significantly enhance both the carbon benefit and the RES integration benefit of smart EVs/HPs.

  6. Overview of NASA Electrified Aircraft Propulsion Research for Large Subsonic Transports

    Science.gov (United States)

    Jansen, Ralph H.; Bowman, Cheryl; Jankovsky, Amy; Dyson, Rodger; Felder, James L.

    2017-01-01

    NASA is investing in Electrified Aircraft Propulsion (EAP) research as part of the portfolio to improve the fuel efficiency, emissions, and noise levels in commercial transport aircraft. Turboelectric, partially turboelectric, and hybrid electric propulsion systems are the primary EAP configurations being evaluated for regional jet and larger aircraft. The goal is to show that one or more viable EAP concepts exist for narrow body aircraft and mature tall-pole technologies related to those concepts. A summary of the aircraft system studies, technology development, and facility development is provided. The leading concept for mid-term (2035) introduction of EAP for a single aisle aircraft is a tube and wing, partially turbo electric configuration (STARC-ABL), however other viable configurations exist. Investments are being made to raise the TRL level of light weight, high efficiency motors, generators, and electrical power distribution systems as well as to define the optimal turbine and boundary layer ingestion systems for a mid-term tube and wing configuration. An electric aircraft power system test facility (NEAT) is under construction at NASA Glenn and an electric aircraft control system test facility (HEIST) is under construction at NASA Armstrong. The correct building blocks are in place to have a viable, large plane EAP configuration tested by 2025 leading to entry into service in 2035 if the community chooses to pursue that goal.

  7. Method of distributing of freight transportations on paralell to motions on the electrified areas

    Directory of Open Access Journals (Sweden)

    N.O. Logvinova

    2012-04-01

    Full Text Available As compared to transportation of loads on tariff distance, it is economic grounded on occasion, it is advantageous to send trains on parallel directions which have more simple type, but longer tariff. With the staring-up of wholesale market of electric power for a railway it is economic advantageous to execute freight transportations in a night-time, that will provide the decline of prime price

  8. Junction Transport in Epitaxial Film Silicon Heterojunction Solar Cells: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Young, D. L.; Li, J. V.; Teplin, C. W.; Stradins, P.; Branz, H. M.

    2011-07-01

    We report our progress toward low-temperature HWCVD epitaxial film silicon solar cells on inexpensive seed layers, with a focus on the junction transport physics exhibited by our devices. Heterojunctions of i/p hydrogenated amorphous Si (a-Si) on our n-type epitaxial crystal Si on n++ Si wafers show space-charge-region recombination, tunneling or diffusive transport depending on both epitaxial Si quality and the applied forward voltage.

  9. Preprinting Microbiology.

    Science.gov (United States)

    Schloss, Patrick D

    2017-05-23

    The field of microbiology has experienced significant growth due to transformative advances in technology and the influx of scientists driven by a curiosity to understand how microbes sustain myriad biochemical processes that maintain Earth. With this explosion in scientific output, a significant bottleneck has been the ability to rapidly disseminate new knowledge to peers and the public. Preprints have emerged as a tool that a growing number of microbiologists are using to overcome this bottleneck. Posting preprints can help to transparently recruit a more diverse pool of reviewers prior to submitting to a journal for formal peer review. Although the use of preprints is still limited in the biological sciences, early indications are that preprints are a robust tool that can complement and enhance peer-reviewed publications. As publishing moves to embrace advances in Internet technology, there are many opportunities for preprints and peer-reviewed journals to coexist in the same ecosystem. Copyright © 2017 Schloss.

  10. Electrifying Australian transport: Hybrid life cycle analysis of a transition to electric light-duty vehicles and renewable electricity

    International Nuclear Information System (INIS)

    Wolfram, Paul; Wiedmann, Thomas

    2017-01-01

    Highlights: •This research assesses life-cycle carbon impacts of different powertrains. •We illustrate a transition to low-carbon vehicles in a hybrid IO-LCA model. •Different electricity and transport scenarios are integrated in the model. •With Australia’s current grid-mix, electric vehicles offer no mitigation potential. •Using renewable energy, electric vehicle carbon footprints can be cut by 66%. -- Abstract: Recent life cycle assessments confirmed the greenhouse gas emission reduction potential of renewable electricity and electric vehicle technologies. However, each technology is usually assessed separately and not within a consistent macro-economic, multi-sectoral framework. Here we present a multi-regional input-output based hybrid approach with integrated scenarios to facilitate the carbon footprint assessment of all direct and indirect effects of a transition to low-emission transportation and electricity generation technologies in Australia. The work takes into account on-road energy consumption values that are more realistic than official drive-cycle energy consumption figures used in previous work. Accounting for these factors as well as for Australia’s grid electricity, which heavily relies on coal power, electric vehicles are found to have a higher carbon footprint than conventional vehicles, whereas hybrid electric vehicles have the lowest. This means that – from a carbon footprint perspective – powertrain electrification is beneficial only to a certain degree at the current stage. This situation can be changed by increasing shares of renewable electricity in the grid. In our best-case scenario, where renewable energy accounts for 96% of the electricity mix in 2050, electric vehicle carbon footprints can be cut by 66% by 2050 relative to 2009. In the business-as-usual scenario (36% renewable electricity share by 2050), electric vehicles can reach a 56% reduction if fossil fuel power plants significantly increase their efficiencies

  11. High Penetration of Renewable Energy in the Transportation Sector: Scenarios, Barriers, and Enablers; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Vimmerstedt, L.; Brown, A.; Heath, G.; Mai, T.; Ruth, M.; Melaina, M.; Simpkins, T.; Steward, D.; Warner, E.; Bertram, K.; Plotkin, S.; Patel, D.; Stephens, T.; Vyas, A.

    2012-06-01

    Transportation accounts for 71% of U.S. petroleum use and 33% of its greenhouse gases emissions. Pathways toward reduced greenhouse gas emissions and petroleum dependence in the transportation sector have been analyzed in considerable detail, but with some limitations. To add to this knowledge, the U.S. Department of Energy has launched a study focused on underexplored greenhouse-gas-abatement and oil-savings opportunities related to transportation. This Transportation Energy Futures study analyzes specific issues and associated key questions to strengthen the existing knowledge base and help cultivate partnerships among federal agencies, state and local governments, and industry.

  12. System-of-Systems Framework for the Future Hydrogen-Based Transportation Economy: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Duffy, M.; Sandor, D.

    2008-06-01

    From a supply chain view, this paper traces the flow of transportation fuels through required systems and addresses the current petroleum-based economy, DOE's vision for a future hydrogen-based transportation economy, and the challenges of a massive market and infrastructure transformation.

  13. Potentials for Platooning in U.S. Highway Freight Transport: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Muratori, Matteo; Holden, Jacob; Lammert, Michael; Duran, Adam; Young, Stanley; Gonder, Jeffrey

    2017-03-15

    Smart technologies enabling connection among vehicles and between vehicles and infrastructure as well as vehicle automation to assist human operators are receiving significant attention as means for improving road transportation systems by reducing fuel consumption - and related emissions - while also providing additional benefits through improving overall traffic safety and efficiency. For truck applications, currently responsible for nearly three-quarters of the total U.S. freight energy use and greenhouse gas (GHG) emissions, platooning has been identified as an early feature for connected and automated vehicles (CAVs) that could provide significant fuel savings and improved traffic safety and efficiency without radical design or technology changes compared to existing vehicles. A statistical analysis was performed based on a large collection of real-world U.S. truck usage data to estimate the fraction of total miles that are technically suitable for platooning. In particular, our analysis focuses on estimating 'platoonable' mileage based on overall highway vehicle use and prolonged high-velocity traveling, establishing that about 65% of the total miles driven by combination trucks could be driven in platoon formation, leading to a 4% reduction in total truck fuel consumption. This technical potential for 'platoonable' miles in the U.S. provides an upper bound for scenario analysis considering fleet willingness to platoon as an estimate of overall benefits of early adoption of CAV technologies. A benefit analysis is proposed to assess the overall potential for energy savings and emissions mitigation by widespread implementation of highway platooning for trucks.

  14. Characterisation, control, and energy management of electrified turbocharged diesel engines

    International Nuclear Information System (INIS)

    Zhao, Dezong; Winward, Edward; Yang, Zhijia; Stobart, Richard; Steffen, Thomas

    2017-01-01

    Highlights: • A real-time energy management framework for electrified engines is proposed. • A multi-variable robust controller is designed. • Characterisation on the air system of electrified diesel engines is given. • Reliable for engine downsizing because of the promising transient performance. - Abstract: The electrification of engine components offers significant opportunities for fuel efficiency improvements. The electrified turbocharger is one of the most attractive options since it recovers part of the engine exhaust gas mechanical energy to assist boosting. Therefore, the engine can be downsized through improved transient responsiveness. In the electrified turbocharger, an electric machine is mounted on the turbine shaft and changes the air system dynamics, so characterisation of the new layout is essential. A systematic control solution is required to manage energy flows in the hybrid system. In this paper, a framework for characterisation, control, and energy management for an electrified turbocharged diesel engine is proposed. The impacts of the electric machine on fuel economy and air system variables are analysed. Based on the characterisation, a two-level control structure is proposed. A real-time energy management strategy is employed as the supervisory level controller to generate the optimal values of critical variables, while a model-based multi-variable controller is designed as the low level controller to track the values. The two controllers work together in a cascade to address both fuel economy optimisation and battery state-of-charge maintenance. The proposed control strategy is validated on a high fidelity physical engine model. The tracking performance shows the proposed framework is a promising solution in regulating the behavior of electrified engines.

  15. Potential for Electrified Vehicles to Contribute to U.S. Petroleum and Climate Goals and Implications for Advanced Biofuels.

    Science.gov (United States)

    Meier, Paul J; Cronin, Keith R; Frost, Ethan A; Runge, Troy M; Dale, Bruce E; Reinemann, Douglas J; Detlor, Jennifer

    2015-07-21

    To examine the national fuel and emissions impacts from increasingly electrified light-duty transportation, we reconstructed the vehicle technology portfolios from two national vehicle studies. Using these vehicle portfolios, we normalized assumptions and examined sensitivity around the rates of electrified vehicle penetration, travel demand growth, and electricity decarbonization. We further examined the impact of substituting low-carbon advanced cellulosic biofuels in place of petroleum. Twenty-seven scenarios were benchmarked against a 50% petroleum-reduction target and an 80% GHG-reduction target. We found that with high rates of electrification (40% of miles traveled) the petroleum-reduction benchmark could be satisfied, even with high travel demand growth. The same highly electrified scenarios, however, could not satisfy 80% GHG-reduction targets, even assuming 80% decarbonized electricity and no growth in travel demand. Regardless of precise consumer vehicle preferences, emissions are a function of the total reliance on electricity versus liquid fuels and the corresponding greenhouse gas intensities of both. We found that at a relatively high rate of electrification (40% of miles and 26% by fuel), an 80% GHG reduction could only be achieved with significant quantities of low-carbon liquid fuel in cases with low or moderate travel demand growth.

  16. PC database for high energy preprint collections

    International Nuclear Information System (INIS)

    Haymaker, R.

    1985-06-01

    We describe a microcomputer database used by the high energy group to keep track of preprints in our collection. It is used as a supplement to the SLAC-SPIRES database to retrieve preprints on hand. This was designed as a low overhead system for a small group

  17. The preprint debate: What are the issues?

    Science.gov (United States)

    da Silva, Jaime A Teixeira

    2018-04-01

    The debate surrounding preprints is increasing. Preprint proponents claim that preprints are a way to shore up trust in academic publishing, that they provide an additional 'quality' screen prior to traditional peer review, that they can assist with the replication crisis plaguing science in part by making negative or contradictory results public, and that they speed up the publishing process because fundamental results can be presented early, serving as timely reports for the purposes of tenure or grant funding. Preprint skeptics and critics claim that preprints may represent a risk and a danger to quality-based academic publishing because they are documents that have not been carefully and thoroughly vetted prior to their release into the public domain. Thus, academics who cite invalid, poorly vetted, or false facts could cause harm, not unlike the unscholarly 'predatory' open access movement. Feedback on work from lesser-known groups, or on less glamorous topics, may be null or worse than from traditional peer review, annulling an initial key objective of preprints. Although there is no widespread empirical evidence or data yet regarding some of these issues, academics should be aware of the ideological, financial, and political tug-of-war taking place before deciding if they wish to publish their important findings as a preprint prior or simultaneous to submitting to a regular journal for peer review.

  18. Preprint Traffic Management and Forecasting System Based on 3D GIS

    OpenAIRE

    Li, Xiaoming; Lv, Zhihan; Hu, Jinxing; Zhang, Baoyun; Yin, Ling; Zhong, Chen; Wang, Weixi; Feng, Shengzhong

    2015-01-01

    This is the preprint version of our paper on 2015 15th IEEE/ACM International Symposium on Cluster, Cloud and Grid Computing (CCGrid). This paper takes Shenzhen Futian comprehensive transportation junction as the case, and makes use of continuous multiple real-time dynamic traffic information to carry out monitoring and analysis on spatial and temporal distribution of passenger flow under different means of transportation and service capacity of junction from multi-dimensional space-time pers...

  19. search.bioPreprint: a discovery tool for cutting edge, preprint biomedical research articles [version 2; referees: 2 approved

    Directory of Open Access Journals (Sweden)

    Carrie L. Iwema

    2016-07-01

    Full Text Available The time it takes for a completed manuscript to be published traditionally can be extremely lengthy. Article publication delay, which occurs in part due to constraints associated with peer review, can prevent the timely dissemination of critical and actionable data associated with new information on rare diseases or developing health concerns such as Zika virus. Preprint servers are open access online repositories housing preprint research articles that enable authors (1 to make their research immediately and freely available and (2 to receive commentary and peer review prior to journal submission. There is a growing movement of preprint advocates aiming to change the current journal publication and peer review system, proposing that preprints catalyze biomedical discovery, support career advancement, and improve scientific communication. While the number of articles submitted to and hosted by preprint servers are gradually increasing, there has been no simple way to identify biomedical research published in a preprint format, as they are not typically indexed and are only discoverable by directly searching the specific preprint server websites. To address this issue, we created a search engine that quickly compiles preprints from disparate host repositories and provides a one-stop search solution. Additionally, we developed a web application that bolsters the discovery of preprints by enabling each and every word or phrase appearing on any web site to be integrated with articles from preprint servers. This tool, search.bioPreprint, is publicly available at http://www.hsls.pitt.edu/resources/preprint.

  20. A Real-Time Systems Symposium Preprint.

    Science.gov (United States)

    1983-09-01

    Real - Time Systems Symposium Preprint Interim Tech...estimate of the occurence of the error. Unclassii ledSECUqITY CLASSIF’ICA T" NO MI*IA If’ inDI /’rrd erter for~~ble. ’Corrputnqg A REAL - TIME SYSTEMS SYMPOSIUM...ABSTRACT This technical report contains a preprint of a paper accepted for presentation at the REAL - TIME SYSTEMS SYMPOSIUM, Arlington,

  1. Entropic lattice Boltzmann model for charged leaky dielectric multiphase fluids in electrified jets.

    Science.gov (United States)

    Lauricella, Marco; Melchionna, Simone; Montessori, Andrea; Pisignano, Dario; Pontrelli, Giuseppe; Succi, Sauro

    2018-03-01

    We present a lattice Boltzmann model for charged leaky dielectric multiphase fluids in the context of electrified jet simulations, which are of interest for a number of production technologies including electrospinning. The role of nonlinear rheology on the dynamics of electrified jets is considered by exploiting the Carreau model for pseudoplastic fluids. We report exploratory simulations of charged droplets at rest and under a constant electric field, and we provide results for charged jet formation under electrospinning conditions.

  2. Preprint data base system at INS: INSPREP system

    International Nuclear Information System (INIS)

    Shinohara, M.; Ukai, K.; Fujiyoshi, N.

    1988-02-01

    The library at the INS (Institute for Nuclear Study) receives several tens of preprints a week from foreign and domestic laboratories and universities. These preprints are pigeonholed by making a catalog card index carried a title, authors, an accession number, classification of fields, etc. A newly arrived preprint lists is also served every week. The cataloging and weekly lists publishing works were handled with a typewriter. And then, it was very difficult and tedious to correct/check/file the index cards and to correct/check the weekly preprint lists. To make a preprint data efficiently by a computer and to refer this data base by on-line without using a index card, the INSPREP system is constructed. The INSPREP system consists of two parts. One is named a PREPINS, and is used to make a preprint data, builds a preprint data base, and publishes a weekly preprint lists. The other, called a PREP, performs an on-line retrieval for this data base. The preprint data base consists of following items such as an author, a title, an accession number, a report number, a classification field, etc. The PREPINS can be used by limited persons for security. User can search a preprint by inputting above mentioned items. The PREP adopts a menu method. Then, user can perform an on-line retrieval very easily. (author)

  3. Citation Patterns to Traditional and Electronic Preprints in the Published Literature.

    Science.gov (United States)

    Youngen, Gregory K.

    1998-01-01

    Identifies the growing importance of electronic preprints in the published literature of physics and astronomy and address several areas of concern regarding the future role of electronic preprints in scientific communication. Topics include a history of preprints in astronomy and physics; inaccuracies in preprint citations; and archival issues.…

  4. Novel approaches for inspiring students and electrifying the public

    Science.gov (United States)

    Lidström, Suzy; Read, Alex; Parke, Stephen; Allen, Roland; Goldfarb, Steven; Mehlhase, Sascha; Ekelöf, Tord; Walker, Alan

    2014-03-01

    We will briefly summarize a wide variety of innovative approaches for inspiring students and stimulating broad public interest in fundamental physics research, as exemplified by recent activities related to the Higgs boson discovery and Higgs-Englert Nobel Prize on behalf of the Swedish Academy, CERN, Fermilab, and the Niels Bohr Institute. Personal interactions with the scientists themselves can be particularly electrifying, and these were encouraged by the wearing of ``Higgs Boson? Ask Me!'' badges, which will be made available to those attending this talk. At CERN, activities include Virtual Visits, (Google) Hangout with CERN, initiatives to grab attention (LEGO models, music videos, art programs, pins, etc.), substantive communication (lab visits and events, museum exhibits, traveling exhibits, local visits, Masterclasses, etc.), and educational activities (summer student programs, semester abroad programs, internships, graduate programs, etc.). For serious students and their teachers, or scientists in other areas, tutorial articles are appropriate. These are most effective if they also incorporate innovative approaches - for example, attractive figures that immediately illustrate the concepts, analogies that will resonate with the reader, and a broadening of perspective. Physica Scripta, Royal Swedish Academy of Sciences.

  5. Ion-ion correlations across and between electrified graphene layers

    Science.gov (United States)

    Mendez-Morales, Trinidad; Burbano, Mario; Haefele, Matthieu; Rotenberg, Benjamin; Salanne, Mathieu

    2018-05-01

    When an ionic liquid adsorbs onto a porous electrode, its ionic arrangement is deeply modified due to a screening of the Coulombic interactions by the metallic surface and by the confinement imposed upon it by the electrode's morphology. In particular, ions of the same charge can approach at close contact, leading to the formation of a superionic state. The impact of an electrified surface placed between two liquid phases is much less understood. Here we simulate a full supercapacitor made of the 1-butyl-3-methylimidazolium hexafluorophosphate and nanoporous graphene electrodes, with varying distances between the graphene sheets. The electrodes are held at constant potential by allowing the carbon charges to fluctuate. Under strong confinement conditions, we show that ions of the same charge tend to adsorb in front of each other across the graphene plane. These correlations are allowed by the formation of a highly localized image charge on the carbon atoms between the ions. They are suppressed in larger pores, when the liquid adopts a bilayer structure between the graphene sheets. These effects are qualitatively similar to the recent templating effects which have been reported during the growth of nanocrystals on a graphene substrate.

  6. An evaluation method of power quality about electrified railways connected to power grid based on PSCAD/EMTDC

    Science.gov (United States)

    Liang, Weibin; Ouyang, Sen; Huang, Xiang; Su, Weijian

    2017-05-01

    The existing modeling process of power quality about electrified railways connected to power grid is complicated and the simulation scene is incomplete, so this paper puts forward a novel evaluation method of power quality based on PSCAD/ETMDC. Firstly, a model of power quality about electrified railways connected to power grid is established, which is based on testing report or measured data. The equivalent model of electrified locomotive contains power characteristic and harmonic characteristic, which are substituted by load and harmonic source. Secondly, in order to make evaluation more complete, an analysis scheme has been put forward. The scheme uses a combination of three-dimensions of electrified locomotive, which contains types, working conditions and quantity. At last, Shenmao Railway is taken as example to evaluate the power quality at different scenes, and the result shows electrified railways connected to power grid have significant effect on power quality.

  7. Supervisory control of a heavy-duty diesel engine with an electrified waste heat recovery system

    NARCIS (Netherlands)

    Feru, E.; Murgovski, N.; de Jager, A.G.; Willems, F.P.T.

    This paper presents an integrated energy and emission management strategy, called Integrated Powertrain Control (IPC), for an Euro-VI diesel engine with an electrified waste heat recovery system. This strategy optimizes the CO2–NOxCO2–NOx trade-off by minimizing the operational costs associated with

  8. Preprint server seeks way to halt plagiarists

    CERN Multimedia

    Giles, J

    2003-01-01

    "An unusual case of plagiarism has struck ArXiv, the popular physics preprint server at Cornell University in Ithaca, New York, resulting in the withdrawal of 22 papers...The plagiarism case traces its origins to June 2002, when Yasushi Watanabe, a high-energy physicist at the Tokyo Insitute of Technology, was contacted by Ramy Noboulsi, who said he was a mathematical physicist" (1 page)

  9. Global Electric Circuit Implications of Total Current Measurements over Electrified Clouds

    Science.gov (United States)

    Mach, Douglas M.; Blakeslee, Richard J.; Bateman, Monte G.

    2009-01-01

    We determined total conduction (Wilson) currents and flash rates for 850 overflights of electrified clouds spanning regions including the Southeastern United States, the Western Atlantic Ocean, the Gulf of Mexico, Central America and adjacent oceans, Central Brazil, and the South Pacific. The overflights include storms over land and ocean, with and without lightning, and with positive and negative Wilson currents. We combined these individual storm overflight statistics with global diurnal lightning variation data from the Lightning Imaging Sensor (LIS) and Optical Transient Detector (OTD) to estimate the thunderstorm and electrified shower cloud contributions to the diurnal variation in the global electric circuit. The contributions to the global electric circuit from lightning producing clouds are estimated by taking the mean current per flash derived from the overflight data for land and ocean overflights and combining it with the global lightning rates (for land and ocean) and their diurnal variation derived from the LIS/OTD data. We estimate the contribution of non-lightning producing electrified clouds by assuming several different diurnal variations and total non-electrified storm counts to produce estimates of the total storm currents (lightning and non-lightning producing storms). The storm counts and diurnal variations are constrained so that the resultant total current diurnal variation equals the diurnal variation in the fair weather electric field (+/-15%). These assumptions, combined with the airborne and satellite data, suggest that the total mean current in the global electric circuit ranges from 2.0 to 2.7 kA, which is greater than estimates made by others using other methods.

  10. Rolling down the throat in NS5-brane background: the case of electrified D-brane

    International Nuclear Information System (INIS)

    Nakayama, Yu; Takayanagi, Hiromitsu; Panigrahi, Kamal L.; Rey, Soo-Jong

    2005-01-01

    We study rolling radion dynamics of electrified D-brane in NS5-brane background, both in effective field theory and in full open string theory. We construct exact boundary states and, from them, extract conserved Noether currents. We argue that T-duality and Lorentz boost offer an intuitive approach. In the limit of large number of NS5-branes, both boundary wave functions and conserved currents are sharply peaked and agree with those deduced from the effective field theory. As the number of NS5-branes is reduced, width around the peak becomes wider by string corrections. We also study radiative decay process. By applying Lorentz covariance, we show how the decay of electrified D-brane is related to that of bare D-brane. We compute spectral moments of final state energy and winding quantum number. Using Lorentz covariance argument, we explain in elementary way why winding quantum number should be included and derive rules how to do so. We conclude that Kutasov's 'geometric realization' between radion rolling dynamics and tachyon rolling dynamics holds universally, both for bare and electrified D-branes. (author)

  11. Panorama 2013 - Focus on the electrified vehicle market

    International Nuclear Information System (INIS)

    Vinot, Simon

    2012-12-01

    Electric vehicles, like hybrid vehicles, are considered to be one of the responses for reducing energy costs and the environmental impact of transport in the form of emissions, whether local (particles, NO x ) or global (CO 2 ). While the hybrid vehicle is gradually becoming generally accepted, the market for electric vehicles is still in its infancy. With models available from car-makers, we look at the reasons underlying their slow development. (author)

  12. Vanadium Redox Flow Battery : Sizing of VRB in electrified heavy construction equipment

    OpenAIRE

    Zimmerman, Nathan

    2014-01-01

    In an effort to reduce global emissions by electrifying vehicles and machines with internal combustion engines has led to the development of batteries that are more powerful and efficient than the common lead acid battery.  One of the most popular batteries being used for such an installation is lithium ion, but due to its short effective usable lifetime, charging time, and costs has driven researcher to other technologies to replace it.  Vanadium redox flow batteries have come into the spotl...

  13. An electrified dust storm over the Negev desert, Israel

    Science.gov (United States)

    Yair, Yoav; Katz, Shai; Yaniv, Roy; Ziv, Baruch; Price, Colin

    2016-11-01

    We report on atmospheric electrical measurements conducted at the Wise Observatory in Mitzpe-Ramon, Israel (30°35‧N, 34°45‧E) during a large dust storm that occurred over the Eastern Mediterranean region on 10-11 February 2015. The dust was transported from the Sahara, Egypt and the Sinai Peninsula ahead of an approaching Cyprus low. Satellite images show the dust plume covering the Negev desert and Southern Israel and moving north. The concentrations of PM10 particles measured by the air-quality monitoring network of the Israeli Ministry of the Environment in Beer-Sheba reached values > 450 μg m- 3 and the AOT from the AERONET station in Sde-Boker was 1.5 on February 10th. The gradual intensification of the event reached peak concentrations on February 11th of over 1200 μg m- 3 and an AOT of 1.8. Continuous measurements of the fair weather vertical electric field (Ez) and vertical current density (Jz) were conducted at the Wise Observatory with 1 minute temporal resolution. Meteorological data was also recorded at the site. As the dust was advected over the observatory, very large fluctuations in the electrical parameters were registered. From the onset of the dust storm, the Ez values changed between + 1000 and + 8000 V m- 1 while the current density fluctuated between - 10 pA m2 and + 20 pA m2, both on time-scales of a few minutes. These values are significant departures from the average fair-weather values measured at the site, which are ~- 200 V m- 1 and ~ 2 pA m2. The disturbed episodes lasted for several hours on February 10th and the 11th and coincided with local meteorological conditions related to the wind speed and direction, which carried large amounts of dust particles over our observation station. We interpret the rapid changes as caused by the transport of electrically charged dust, carrying an excess of negative charge at lower altitudes.

  14. One-shot service searches: Preprint repositories at a mouseclick

    International Nuclear Information System (INIS)

    Canessa, E.; Pastore, G.

    1996-09-01

    In this article we introduce the ICTP-International Centre for Theoretical Physics's prototype for a ''One-Shot World-Wide Preprints Search'' on the Web. This is a new centralized interface for a global search throughout the most popular scientific preprint repositories. Herein, we briefly discuss our experience with the implementation of this service and propose it as a possible alternative solution to the problem of getting access to the information without being either overloaded with lots of new documents or not being informed at all. (author). 13 refs, 3 figs

  15. One-shot service searches: Preprint repositories at a mouseclick

    Energy Technology Data Exchange (ETDEWEB)

    Canessa, E [International Centre for Theoretical Physics, Trieste (Italy); Pastore, G [Trieste Univ., Trieste (Italy). Dipt. di Fisica

    1996-09-01

    In this article we introduce the ICTP-International Centre for Theoretical Physics`s prototype for a ``One-Shot World-Wide Preprints Search`` on the Web. This is a new centralized interface for a global search throughout the most popular scientific preprint repositories. Herein, we briefly discuss our experience with the implementation of this service and propose it as a possible alternative solution to the problem of getting access to the information without being either overloaded with lots of new documents or not being informed at all. (author). 13 refs, 3 figs.

  16. Electrifying biomass

    International Nuclear Information System (INIS)

    Kusnierczyk, D.

    2005-01-01

    British Columbia's (BC) energy plan was outlined in this PowerPoint presentation. BC Hydro is the third largest electric utility in Canada with a generating capacity of 11,000 MW, 90 per cent of which is hydro generation. Various independent power project (IPP) biomass technologies were outlined, including details of biogas, wood residue and municipal solid waste facilities. An outline of BC Hydro's overall supply mix was presented, along with details of the IPP supply mix. It was suggested that the cancellation of the Duke Point power project has driven growth in the renewable energy sector. A chart of potential energy contribution by resource type was presented, as well as unit energy cost ranges. Resources included small and large hydro; demand side management; resource smart natural gas; natural gas; coal; wind; geothermal; biomass; wave; and tidal. The acquisition process was reviewed. Details of calls for tenders were presented, and issues concerning bidder responsibility and self-selection were examined. It was observed that wood residue presents a firm source of electricity that is generally local, and has support from the public. In addition, permits for wood residue energy conversion are readily available. However, size limitations, fuel risks, and issues concerning site control may prove to be significant challenges. It was concluded that the success of biomass energy development will depend on adequate access and competitive pricing. tabs., figs

  17. Electromagnetic interference produced by power or electrified railway lines on metallic pipe networks

    International Nuclear Information System (INIS)

    Lucca, G.

    1999-01-01

    The paper presents an algorithm for the calculation, in the frequency domain, of the induced voltages and currents on a generic metallic pipe network exposed to the electromagnetic interference from a power line or an electrified railway line. By assuming as known the voltages and the currents on the inducing line, the algorithm may be subdivided into the following main steps: a) determination of the ideal electromotive force and current generators to be applied to the induced structure in order to represent the electromagnetic influence from the inducing line; b) modelling of the pipe network by means of a suitable equivalent electric network; c) calculation of voltages and currents on the induced network [it

  18. Lightning mapping and dual-polarization radar observations of electrified storms at Langmuir Laboratory

    Science.gov (United States)

    Krehbiel, P. R.; Hyland, P. T.; Edens, H. E.; Rison, W.

    2013-12-01

    Observations being made at Langmuir Laboratory with the NM Tech Lightning Mapping Array (LMA) and the University of Oklahoma ARRC PX-1000 dual polarization X-band radar strongly confirm and expand upon the normal polarity tripolar electrical structure of central New Mexico storms. This is in sharp contrast with the anomalously electrified storm structures observed in northern Colorado during and subsequent to the 2012 DC3 field campaign, as seen with North Colorado LMA and CSU CHILL dual-polarization radar observations. In this presentation we focus on the New Mexico observations, and several modes in which the tripolar structure appears initially to develop and evolve with time. Central New Mexico storms are often prolific producers of negative cloud-to-ground (CG) flashes, but rarely produce positive CGs. By contrast, many or most north Colorado storms are CG-deficient, with the relatively few CG discharges being of predominantly positive polarity. In addition, NM storms commonly produce bolt-from-the-blue (BFB) negative CGs, whereas anomalously electrified Colorado storms produce none. The occurrence of BFBs is indicative of a relatively weak lower positive charge region, while the occurrence of normal downward -CGs is indicative of a somewhat stronger lower positive charge. The lack of -CGs in Colorado storms results from lower positive charge being a dominant storm charge that is elevated in altitude. These and other basic features of the electrically activity of storms, coupled with dual polarization and Doppler radar observations of hydrometeor types and motions, are leading to a better understanding of the storm electrification processes.

  19. Well-to-wheel greenhouse gas emissions and energy use analysis of hypothetical fleet of electrified vehicles in Canada and the U.S

    Science.gov (United States)

    Maduro, Miguelangel

    The shift to strong hybrid and electrified vehicle architectures engenders controversy and brings about many unanswered questions. It is unclear whether developed markets will have the infrastructure in place to support and successfully implement them. To date, limited effort has been made to comprehend if the energy and transportation solutions that work well for one city or geographic region may extend broadly. A region's capacity to supply a fleet of EVs, or plug-in hybrid vehicles with the required charging infrastructure, does not necessarily make such vehicle architectures an optimal solution. In this study, a mix of technologies ranging from HEV to PHEV and EREV through to Battery Electric Vehicles were analyzed and set in three Canadian Provinces and 3 U.S. Regions for the year 2020. Government agency developed environmental software tools were used to estimate greenhouse gas emissions and energy use. Projected vehicle technology shares were employed to estimate regional environmental implications. Alternative vehicle technologies and fuels are recommended for each region based on local power generation schemes.

  20. Use of alternating and pulsed direct current electrified fields for zebra mussel control

    Science.gov (United States)

    Luoma, James A.; Dean, Jan C.; Severson, Todd J.; Wise, Jeremy K.; Barbour, Matthew

    2017-01-01

    Alternatives to chemicals for controlling dreissenid mussels are desirable for environmental compatibility, but few alternatives exist. Previous studies have evaluated the use of electrified fields for stunning and/or killing planktonic life stages of dreissenid mussels, however, the available literature on the use of electrified fields to control adult dreissenid mussels is limited. We evaluated the effects of sinusoidal alternating current (AC) and 20% duty cycle square-wave pulsed direct current (PDC) exposure on the survival of adult zebra mussels at water temperatures of 10, 15, and 22 °C. Peak voltage gradients of ~ 17 and 30 Vp/cm in the AC and PDC exposures, respectively, were continuously applied for 24, 48, or 72 h. Peak power densities ranged from 77,999 to 107,199 µW/cm3 in the AC exposures and 245,320 to 313,945 µW/cm3 in the PDC exposures. The peak dose ranged from 6,739 to 27,298 Joules/cm3 and 21,306 to 80,941 Joules/cm3 in the AC and PDC exposures, respectively. The applied power ranged from 16.6 to 68.9 kWh in the AC exposures and from 22.2 to 86.4 kWh in the PDC exposures. Mortality ranged from 2.7 to 92.7% in the AC exposed groups and from 24.0 to 98.7% in PDC exposed groups. Mortality increased with corresponding increases in water temperature and exposure duration, and we observed more zebra mussel mortality in the PDC exposures. Exposures conducted with AC required less of a peak dose (Joules/cm3) but more applied power (kWh) to achieve the same level of adult zebra mussel mortality as corresponding PDC exposures. The results demonstrate that 20% duty cycle square-wave PDC requires less energy than sinusoidal AC to inducing the same level of adult zebra mussel mortality.

  1. Preprint WebVRGIS Based Traffic Analysis and Visualization System

    OpenAIRE

    Li, Xiaoming; Lv, Zhihan; Wang, Weixi; Zhang, Baoyun; Hu, Jinxing; Yin, Ling; Feng, Shengzhong

    2015-01-01

    This is the preprint version of our paper on Advances in Engineering Software. With several characteristics, such as large scale, diverse predictability and timeliness, the city traffic data falls in the range of definition of Big Data. A Virtual Reality GIS based traffic analysis and visualization system is proposed as a promising and inspiring approach to manage and develop traffic big data. In addition to the basic GIS interaction functions, the proposed system also includes some intellige...

  2. New regenerative braking control strategy for rear-driven electrified minivans

    International Nuclear Information System (INIS)

    Junzhi, Zhang; Yutong, Li; Chen, Lv; Ye, Yuan

    2014-01-01

    Highlights: • A regenerative braking system is designed for a rear-driven electric minivan. • A new control strategy coordinating energy efficiency and braking feel is proposed. • The control strategy is verified by simulation and hardware-in-loop (HIL) tests. • The proposed control strategy offers higher regeneration efficiency. - Abstract: As of to 2012, minivan ownership stood at 20 million units in China, accounting for 16% of the passenger car market. In this article, comprehensive research is carried out on the design and control of a regenerative braking system for a rear-driven electrified minivan. For improving the regeneration efficiency by as much as possible, a new regenerative braking control strategy called “modified control strategy” is proposed. Additionally, a control strategy called “baseline control strategy” is introduced as a comparative control strategy. Simulations and hardware-in-loop (HIL) tests are carried out. The results of the simulations and the HIL tests show that the modified control strategy offers considerably higher regeneration efficiency than the baseline control strategy. In normal deceleration braking, the regeneration efficiency of the modified control strategy reaches 47%, 15% higher than that of the baseline control strategy. In addition, improvement in the fuel economy of electric vehicles operating on the ECE driving cycle and enhanced with the modified control strategy is greater than 10%, which is 3% higher than that with the baseline control strategy

  3. The prehistory of biology preprints: A forgotten experiment from the 1960s.

    Directory of Open Access Journals (Sweden)

    Matthew Cobb

    2017-11-01

    Full Text Available In 1961, the National Institutes of Health (NIH began to circulate biological preprints in a forgotten experiment called the Information Exchange Groups (IEGs. This system eventually attracted over 3,600 participants and saw the production of over 2,500 different documents, but by 1967, it was effectively shut down following the refusal of journals to accept articles that had been circulated as preprints. This article charts the rise and fall of the IEGs and explores the parallels with the 1990s and the biomedical preprint movement of today.

  4. The prehistory of biology preprints: A forgotten experiment from the 1960s.

    Science.gov (United States)

    Cobb, Matthew

    2017-11-01

    In 1961, the National Institutes of Health (NIH) began to circulate biological preprints in a forgotten experiment called the Information Exchange Groups (IEGs). This system eventually attracted over 3,600 participants and saw the production of over 2,500 different documents, but by 1967, it was effectively shut down following the refusal of journals to accept articles that had been circulated as preprints. This article charts the rise and fall of the IEGs and explores the parallels with the 1990s and the biomedical preprint movement of today.

  5. Reliable and repeatable bonding technology for high temperature automotive power modules for electrified vehicles

    International Nuclear Information System (INIS)

    Yoon, Sang Won; Shiozaki, Koji; Glover, Michael D; Mantooth, H Alan

    2013-01-01

    This paper presents the feasibility of highly reliable and repeatable copper–tin transient liquid phase (Cu–Sn TLP) bonding as applied to die attachment in high temperature operational power modules. Electrified vehicles are attracting particular interest as eco-friendly vehicles, but their power modules are challenged because of increasing power densities which lead to high temperatures. Such high temperature operation addresses the importance of advanced bonding technology that is highly reliable (for high temperature operation) and repeatable (for fabrication of advanced structures). Cu–Sn TLP bonding is employed herein because of its high remelting temperature and desirable thermal and electrical conductivities. The bonding starts with a stack of Cu–Sn–Cu metal layers that eventually transforms to Cu–Sn alloys. As the alloys have melting temperatures (Cu 3 Sn: > 600 °C, Cu 6 Sn 5 : > 400 °C) significantly higher than the process temperature, the process can be repeated without damaging previously bonded layers. A Cu–Sn TLP bonding process was developed using thin Sn metal sheets inserted between copper layers on silicon die and direct bonded copper substrates, emulating the process used to construct automotive power modules. Bond quality is characterized using (1) proof-of-concept fabrication, (2) material identification using scanning electron microscopy and energy-dispersive x-ray spectroscopy analysis, and (3) optical analysis using optical microscopy and scanning acoustic microscope. The feasibility of multiple-sided Cu–Sn TLP bonding is demonstrated by the absence of bondline damage in multiple test samples fabricated with double- or four-sided bonding using the TLP bonding process. (paper)

  6. Protein adsorption at the electrified air-water interface: implications on foam stability.

    Science.gov (United States)

    Engelhardt, Kathrin; Rumpel, Armin; Walter, Johannes; Dombrowski, Jannika; Kulozik, Ulrich; Braunschweig, Björn; Peukert, Wolfgang

    2012-05-22

    The surface chemistry of ions, water molecules, and proteins as well as their ability to form stable networks in foams can influence and control macroscopic properties such as taste and texture of dairy products considerably. Despite the significant relevance of protein adsorption at liquid interfaces, a molecular level understanding on the arrangement of proteins at interfaces and their interactions has been elusive. Therefore, we have addressed the adsorption of the model protein bovine serum albumin (BSA) at the air-water interface with vibrational sum-frequency generation (SFG) and ellipsometry. SFG provides specific information on the composition and average orientation of molecules at interfaces, while complementary information on the thickness of the adsorbed layer can be obtained with ellipsometry. Adsorption of charged BSA proteins at the water surface leads to an electrified interface, pH dependent charging, and electric field-induced polar ordering of interfacial H(2)O and BSA. Varying the bulk pH of protein solutions changes the intensities of the protein related vibrational bands substantially, while dramatic changes in vibrational bands of interfacial H(2)O are simultaneously observed. These observations have allowed us to determine the isoelectric point of BSA directly at the electrolyte-air interface for the first time. BSA covered air-water interfaces with a pH near the isoelectric point form an amorphous network of possibly agglomerated BSA proteins. Finally, we provide a direct correlation of the molecular structure of BSA interfaces with foam stability and new information on the link between microscopic properties of BSA at water surfaces and macroscopic properties such as the stability of protein foams.

  7. Nanoscale Resolution 3D Printing with Pin-Modified Electrified Inkjets for Tailorable Nano/Macrohybrid Constructs for Tissue Engineering.

    Science.gov (United States)

    Kim, Jeong In; Kim, Cheol Sang

    2018-04-18

    Cells respond to their microenvironment, which is of a size comparable to that of the cells. The macroscale features of three-dimensional (3D) printing struts typically result in whole cell contact guidance (CCG). In contrast, at the nanoscale, where features are of a size similar to that of receptors of cells, the response of cells is more complex. The cell-nanotopography interaction involves nanoscale adhesion localized structures, which include cell adhesion-related particles that change in response to the clustering of integrin. For this reason, it is necessary to develop a technique for manufacturing tailorable nano/macrohybrid constructs capable of freely controlling the cellular activity. In this study, a hierarchical 3D nano- to microscale hybrid structure was fabricated by combinational processing of 3D printing and electrified inkjet spinning via pin motions. This method overcomes the disadvantages of conventional 3D printing, providing a novel combinatory technique for the fabrication of 3D hybrid constructs with excellent cell proliferation. Through a pin-modified electrified inkjet spinning, we have successfully fabricated customizable nano-/microscale hybrid constructs in a fibrous or mesh form, which can control the cell fate. We have conducted this study of cell-topography interactions from the fabrication approach to accelerate the development of next-generation 3D scaffolds.

  8. An Analytical Design Method for a Regenerative Braking Control System for DC-electrified Railway Systems under Light Load Conditions

    Science.gov (United States)

    Saito, Tatsuhito; Kondo, Keiichiro; Koseki, Takafumi

    A DC-electrified railway system that is fed by diode rectifiers at a substation is unable to return the electric power to an AC grid. Accordingly, the braking cars have to restrict regenerative braking power when the power consumption of the powering cars is not sufficient. However, the characteristics of a DC-electrified railway system, including the powering cars, is not known, and a mathematical model for designing a controller has not been established yet. Hence, the object of this study is to obtain the mathematical model for an analytical design method of the regenerative braking control system. In the first part of this paper, the static characteristics of this system are presented to show the position of the equilibrium point. The linearization of this system at the equilibrium point is then performed to describe the dynamic characteristics of the system. An analytical design method is then proposed on the basis of these characteristics. The proposed design method is verified by experimental tests with a 1kW class miniature model, and numerical simulations.

  9. Relative Contributions of Electrified Shower Clouds and Thunderstorms to the Global Circuit: Can 10 Years of TRMM Data Help Solve an Old Puzzle? (Invited)

    Science.gov (United States)

    Zipser, E. J.; Liu, C.; Williams, E.; Burns, G. B.

    2010-12-01

    The long-standing mainstay of support for C.T.R. Wilson’s global circuit hypothesis is the similarity between the diurnal variation of thunderstorm days in universal time, and the Carnegie curve of electrical potential gradient (Whipple, 1929). This rough agreement has sustained the widespread view that thunderstorms are the “batteries” for the global electrical circuit. This study utilizes 10 years of Tropical Rainfall Measuring Mission (TRMM) observations to quantify the global occurrence of thunderstorms with much better accuracy and validate the comparison by Whipple 80 years ago. The results support Wilson’s (1920) original ideas that both thunderstorms and electrified shower clouds contribute to the DC global circuit by virtue of negative charge carried downward by precipitation. First, the precipitation features (PFs) are defined by grouping the pixels with rain using 10 years of TRMM observations. Thunderstorms are identified from these PFs with lightning flashes observed by the Lightning Imaging Sensor. PFs without lightning flashes but with the 30 dBZ radar echo top temperature below -10oC over land and -17 oC over ocean are selected as possibly electrified shower clouds. The universal diurnal variation of rainfall, raining area from the thunderstorms and possibly electrified shower clouds in different seasons are derived and compared with the diurnal variations of the electric field observed at Vostok, Antarctica. The result shows a substantially better match from the updated diurnal variations of the thunderstorm area to the Carnegie curve than Whipple showed. One reason for the improvement is that the TRMM data are able to distinguish the relatively larger contributions from electrified shower clouds than thunderstorms over tropical oceans and over the Amazon. Potential further refinements to the current algorithm defining electrified convective cells are discussed.

  10. Optimizing the design of preprinted orders for ambulatory chemotherapy: combining oncology, human factors, and graphic design.

    Science.gov (United States)

    Jeon, Jennifer; White, Rachel E; Hunt, Richard G; Cassano-Piché, Andrea L; Easty, Anthony C

    2012-03-01

    To establish a set of guidelines for developing ambulatory chemotherapy preprinted orders. Multiple methods were used to develop the preprinted order guidelines. These included (A) a comprehensive literature review and an environmental scan; (B) analyses of field study observations and incident reports; (C) critical review of evidence from the literature and the field study observation analyses; (D) review of the draft guidelines by a clinical advisory group; and (E) collaboration with graphic designers to develop sample preprinted orders, refine the design guidelines, and format the resulting content. The Guidelines for Developing Ambulatory Chemotherapy Preprinted Orders, which consist of guidance on the design process, content, and graphic design elements of ambulatory chemotherapy preprinted orders, have been established. Health care is a safety critical, dynamic, and complex sociotechnical system. Identifying safety risks in such a system and effectively addressing them often require the expertise of multiple disciplines. This study illustrates how human factors professionals, clinicians, and designers can leverage each other's expertise to uncover commonly overlooked patient safety hazards and to provide health care professionals with innovative, practical, and user-centered tools to minimize those hazards.

  11. X-ray Reflectivity Study of Ionic Liquids at Electrified Surfaces

    Science.gov (United States)

    Chu, Miaoqi

    previous chapters are employed to extract information about the solid-liquid interface. Electron density depletion due to methyl terminal of solvent molecules (methyl gap) and due to the reduced surface density compared to the bulk density (density gap) are analyzed. In the next Chapter, XRR technique is employed to study the structures and dynamics of room temperature ionic liquids (RTILs) at an electrified surface. RTILs are molten salts at room temperature, consisted purely by anions and cations, with potential applications in energy storage, electro-synthesis, electrodeposition etc. The solvent-free and high charge concentrated novel liquids process many unique properties that not seen in normal dilute salt solution. It is predicted that when a surface isn't highly charged, RTILs form alternating layers of anion/cation to screen the surface charge; when it's highly charged, a crowding layer with ions with like charge forms. The alternating structure has been observed experimentally but not the crowding layer. Following the rules of optimization XRR experiment in Chapter 2, conductive silicon which has small electron density is used which maximize the EDP contrast. This makes it possible to directly observe the formation of crowding layer. The thickness of this crowding layer, charge distributions and compositions as a function of applied voltage. The dynamics of anion/cation reorganization in RTILs determine the power density for RTILs? energy application. In Chapter 5, the time-dependence of the formation and dissipation of the crowding layer is studied with XRR. An ultra-slow dynamic, much longer than the typical RC time constant, is revealed. Comparisons with theoretical predications and experiments studies are made in order to understand the origin of this process. The thesis is summarized in Chapter 6, along with several proposals for future work.

  12. On the man-made contamination on ULF measurements: evidence for disturbances related to an electrified DC railway

    Science.gov (United States)

    Villante, U.; Piancatelli, A.; Palangio, P.

    2014-09-01

    An analysis of measurements performed at L'Aquila (Italy) during a deep minimum of solar and magnetospheric activity (2008-2010) allowed for the evaluation of possible contamination of the ultralow-frequency (ULF) spectrum (f ≈ 1-500 mHz) from artificial disturbances, practically in absence of natural signals. In addition, the city evacuation and the interruption of all industrial and social activities after the strong earthquake of 6 April 2009 allowed also for the examination of possible changes of the contamination level under remarkably changed environmental conditions. Our analysis reveals a persistent, season-independent, artificial signal, with the same characteristics in the H and Z components, that affects during daytime hours the entire spectrum; such contamination persists after the city evacuation. We speculate that the DC electrified railway (located ≈ 33 km from the Geomagnetic Observatory of L'Aquila, it maintained the same train traffic after the earthquake) is responsible for the observed disturbances.

  13. Voltage-dependent cluster expansion for electrified solid-liquid interfaces: Application to the electrochemical deposition of transition metals

    Science.gov (United States)

    Weitzner, Stephen E.; Dabo, Ismaila

    2017-11-01

    The detailed atomistic modeling of electrochemically deposited metal monolayers is challenging due to the complex structure of the metal-solution interface and the critical effects of surface electrification during electrode polarization. Accurate models of interfacial electrochemical equilibria are further challenged by the need to include entropic effects to obtain accurate surface chemical potentials. We present an embedded quantum-continuum model of the interfacial environment that addresses each of these challenges and study the underpotential deposition of silver on the gold (100) surface. We leverage these results to parametrize a cluster expansion of the electrified interface and show through grand canonical Monte Carlo calculations the crucial need to account for variations in the interfacial dipole when modeling electrodeposited metals under finite-temperature electrochemical conditions.

  14. A framework for the exergy analysis of future transport pathways: Application for the United Kingdom transport system 2010–2050

    International Nuclear Information System (INIS)

    Byers, Edward A.; Gasparatos, Alexandros; Serrenho, André C.

    2015-01-01

    Exergy analysis has been used to quantify the historical resource use efficiency and environmental impact of transport systems. However, few exergy studies have explored future transport pathways. This study aims to, (a) develop a conceptual framework for the exergy analysis of multiple future transport and electricity pathways, (b) apply this framework to quantify future resource consumption and service delivery patterns, (c) discuss the policy-relevant results that exergy studies of future transport systems can offer. Multiple transport and electricity pathways developed by the UK Government are used to explore changes in energy use, useful work delivery and greenhouse gas emissions. In passenger transport, ambitious electrification results in a 20% increase of useful work delivery, whilst reducing GHG emissions and energy consumption by 65%. For freight, international shipping and aviation, smaller exergy efficiency improvements make useful work delivery and greenhouse gas emissions highly dependent on transport demand. Passenger transport electrification brings a step-change in useful work delivery, which if accompanied by low-carbon electricity, significantly reduces greenhouse gas emissions. The efficiency of low-carbon electricity systems is significant for useful work delivery, but not dominant across the scenarios explored. High penetration of renewables and electrified transport is the most resource-efficient combination in this context. - Highlights: • Develop an exergy analysis framework of future transport pathways and apply it to UK. • Electrification of personal transport brings step change in useful work delivery. • Efficiency of electricity supply becomes significant once transport is electrified. • High electrification increases useful work (+20%) and reduces emissions (−65%). • High penetration of renewables and electrified transport is most resource efficient

  15. Optimal design and allocation of electrified vehicles and dedicated charging infrastructure for minimum life cycle greenhouse gas emissions and cost

    International Nuclear Information System (INIS)

    Traut, Elizabeth; Hendrickson, Chris; Klampfl, Erica; Liu, Yimin; Michalek, Jeremy J.

    2012-01-01

    Electrified vehicles can reduce greenhouse gas (GHG) emissions by shifting energy demand from gasoline to electricity. GHG reduction potential depends on vehicle design, adoption, driving and charging patterns, charging infrastructure, and electricity generation mix. We construct an optimization model to study these factors by determining optimal design of conventional vehicles, hybrid electric vehicles (HEVs), plug-in hybrid electric vehicles (PHEVs), and battery electric vehicles (BEVs) with optimal allocation of vehicle designs and dedicated workplace charging infrastructure in the fleet for minimum life cycle cost or GHG emissions over a range of scenarios. We focus on vehicles with similar body size and acceleration to a Toyota Prius under government 5-cycle driving conditions. We find that under the current US grid mix, PHEVs offer only small GHG emissions reductions compared to HEVs, and workplace charging is insignificant. With grid decarbonization, PHEVs and BEVs offer substantial GHG emissions reductions, and workplace charging provides additional benefits. HEVs are optimal or near-optimal for minimum cost in most scenarios. High gas prices and low vehicle and battery costs are the major drivers for PHEVs and BEVs to enter and dominate the cost-optimal fleet. Carbon prices have little effect. Cost and range restrictions limit penetration of BEVs. - Highlights: ► We pose an MINLP model to minimize cost and GHG emissions of electrified vehicles. ► We design PHEVs and BEVs and assign vehicles and charging infrastructure in US fleet. ► Under US grid mix, PEVs provide minor GHG reductions and work chargers do little. ► HEVs are robust; PEVs and work charging potential improve with a decarbonized grid. ► We quantify factors needed for PEVs to enter and dominate the optimal fleet.

  16. Transportation

    National Research Council Canada - National Science Library

    Adams, James; Carr, Ron; Chebl, Maroun; Coleman, Robert; Costantini, William; Cox, Robert; Dial, William; Jenkins, Robert; McGovern, James; Mueller, Peter

    2006-01-01

    ...., trains, ships, etc.) and maximizing intermodal efficiency. A healthy balance must be achieved between the flow of international commerce and security requirements regardless of transportation mode...

  17. Transportation

    International Nuclear Information System (INIS)

    Anon.

    1998-01-01

    Here is the decree of the thirtieth of July 1998 relative to road transportation, to trade and brokerage of wastes. It requires to firms which carry out a road transportation as well as to traders and to brokers of wastes to declare their operations to the prefect. The declaration has to be renewed every five years. (O.M.)

  18. ELECTROMAGNETIC SAFETY OF ELECTRIC TRANSPORT SYSTEMS: MAIN SOURCES AND PARAMETERS OF MAGNETIC FIELDS

    Directory of Open Access Journals (Sweden)

    N. G. Ptitsyna

    2013-03-01

    Full Text Available Magnetic fields produced by electric drive vehicles may break electromagnetic safety. For electromagnetic safety and electromagnetic compatibility knowledge about characteristics and sources of magnetic fields in the electric transport is necessary. The article deals with analysis of available data about magnetic fields in electric cars and comparison with results of our measurements carried out in the other types of electrified transport systems.

  19. Analyzing Potential Grid Impacts from Future In-Motion Roadway Wireless Power Transfer Scenarios: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Meintz, Andrew; Gonder, Jeffrey; Jorgenson, Jennie; Brooker, Aaron

    2016-08-01

    This work examines the grid impact of in-motion roadway wireless power transfer through the examination of the electrification of high-capacity roadways inside a metropolitan area. The work uses data from a regional travel study and the Federal Highway Administration's Highway Performance Monitoring System to estimate the electrified roadway's hourly power use throughout a week. The data are then combined with hourly grid load estimates for the same metropolitan area to determine the overlay of traditional grid load with additional load from a future electrified roadway.

  20. Transportation

    National Research Council Canada - National Science Library

    Allshouse, Michael; Armstrong, Frederick Henry; Burns, Stephen; Courts, Michael; Denn, Douglas; Fortunato, Paul; Gettings, Daniel; Hansen, David; Hoffman, D. W; Jones, Robert

    2007-01-01

    .... The ability of the global transportation industry to rapidly move passengers and products from one corner of the globe to another continues to amaze even those wise to the dynamics of such operations...

  1. Time-varying delays compensation algorithm for powertrain active damping of an electrified vehicle equipped with an axle motor during regenerative braking

    Science.gov (United States)

    Zhang, Junzhi; Li, Yutong; Lv, Chen; Gou, Jinfang; Yuan, Ye

    2017-03-01

    The flexibility of the electrified powertrain system elicits a negative effect upon the cooperative control performance between regenerative and hydraulic braking and the active damping control performance. Meanwhile, the connections among sensors, controllers, and actuators are realized via network communication, i.e., controller area network (CAN), that introduces time-varying delays and deteriorates the control performances of the closed-loop control systems. As such, the goal of this paper is to develop a control algorithm to cope with all these challenges. To this end, the models of the stochastic network induced time-varying delays, based on a real in-vehicle network topology and on a flexible electrified powertrain, were firstly built. In order to further enhance the control performances of active damping and cooperative control of regenerative and hydraulic braking, the time-varying delays compensation algorithm for the electrified powertrain active damping during regenerative braking was developed based on a predictive scheme. The augmented system is constructed and the H∞ performance is analyzed. Based on this analysis, the control gains are derived by solving a nonlinear minimization problem. The simulations and hardware-in-loop (HIL) tests were carried out to validate the effectiveness of the developed algorithm. The test results show that the active damping and cooperative control performances are enhanced significantly.

  2. Reducing residential solid fuel combustion through electrified space heating leads to substantial air quality, health and climate benefits in China's Beijing-Tianjin-Hebei region

    Science.gov (United States)

    Yang, J.; Mauzerall, D. L.

    2017-12-01

    During periods of high pollution in winter, household space heating can contribute more than half of PM2.5 concentrations in China's Beijing-Tianjin-Hebei (BTH) region. The majority of rural households and some urban households in the region still heat with small stoves and solid fuels such as raw coal, coal briquettes and biomass. Thus, reducing emissions from residential space heating has become a top priority of the Chinese government's air pollution mitigation plan. Electrified space heating is a promising alternative to solid fuel. However, there is little analysis of the air quality and climate implications of choosing various electrified heating devices and utilizing different electricity sources. Here we conduct an integrated assessment of the air quality, human health and climate implications of various electrified heating scenarios in the BTH region using the Weather Research and Forecasting model with Chemistry. We use the Multi-resolution Emission Inventory for China for the year 2012 as our base case and design two electrification scenarios in which either direct resistance heaters or air source heat pumps are installed to replace all household heating stoves. We initially assume all electrified heating devices use electricity from supercritical coal-fired power plants. We find that installing air source heat pumps reduces CO2 emissions and premature deaths due to PM2.5 pollution more than resistance heaters, relative to the base case. The increased health and climate benefits of heat pumps occur because they have a higher heat conversion efficiency and thus require less electricity for space heating than resistance heaters. We also find that with the same heat pump installation, a hybrid electricity source (40% of the electricity generated from renewable sources and the rest from coal) further reduces both CO2 emissions and premature deaths than using electricity only from coal. Our study demonstrates the air pollution and CO2 mitigation potential and

  3. Estimation of droplet charge forming out of an electrified ligament in the presence of a uniform electric field

    International Nuclear Information System (INIS)

    Osman, H; Castle, G S P; Adamiak, K; Fan, H T; Simmer, J

    2015-01-01

    The charge on a liquid droplet is a critical parameter that needs to be determined to accurately predict the behaviour of the droplet in many electrostatic applications, for example, electrostatic painting and ink-jet printing. The charge depends on many factors, such as the liquid conductivity, droplet and ligament radii, ligament length, droplet shape, electric field intensity, space charge, the presence of adjacent ligaments and previously formed droplets. In this paper, a 2D axisymmetric model is presented which can be used to predict the electric charge on a conductive spherical droplet ejected from a single ligament directly supplied with high voltage. It was found that the droplet charging levels for the case of isolated electrified ligaments are as much as 60 times higher than that in the case of ligaments connected to a planar high voltage electrode. It is suggested that practical atomization systems lie somewhere between these two extremes and that a better model was achieved by developing a 3D approximation of a linear array of ligaments connected to an electrode having variable width. The effect on droplet charge and its radius was estimated for several cases of different boundary conditions. (paper)

  4. On the man-made contamination on ULF measurements: evidence for disturbances related to an electrified DC railway

    Directory of Open Access Journals (Sweden)

    U. Villante

    2014-09-01

    Full Text Available An analysis of measurements performed at L'Aquila (Italy during a deep minimum of solar and magnetospheric activity (2008–2010 allowed for the evaluation of possible contamination of the ultralow-frequency (ULF spectrum (f ≈ 1–500 mHz from artificial disturbances, practically in absence of natural signals. In addition, the city evacuation and the interruption of all industrial and social activities after the strong earthquake of 6 April 2009 allowed also for the examination of possible changes of the contamination level under remarkably changed environmental conditions. Our analysis reveals a persistent, season-independent, artificial signal, with the same characteristics in the H and Z components, that affects during daytime hours the entire spectrum; such contamination persists after the city evacuation. We speculate that the DC electrified railway (located ≈ 33 km from the Geomagnetic Observatory of L'Aquila, it maintained the same train traffic after the earthquake is responsible for the observed disturbances.

  5. Transportation

    Science.gov (United States)

    2007-01-01

    Faculty ii INDUSTRY TRAVEL Domestic Assistant Deputy Under Secretary of Defense (Transportation Policy), Washington, DC Department of...developed between the railroad and trucking industries. Railroads: Today’s seven Class I freight railroad systems move 42% of the nation’s intercity ...has been successfully employed in London to reduce congestion and observed by this industry study during its travels . It is currently being

  6. Analysis of Fast Charging Station Network for Electrified Ride-Hailing Services

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rames, Clement L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kontou, Eleftheria [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Motoaki, Yutaka [Idaho National Laboratory; Smart, John [Idaho National Laboratory; Zhou, Zhi [Argonne National Laboratory

    2018-04-03

    Today's electric vehicle (EV) owners charge their vehicles mostly at home and seldom use public direct current fast charger (DCFCs), reducing the need for a large deployment of DCFCs for private EV owners. However, due to the emerging interest among transportation network companies to operate EVs in their fleet, there is great potential for DCFCs to be highly utilized and become economically feasible in the future. This paper describes a heuristic algorithm to emulate operation of EVs within a hypothetical transportation network company fleet using a large global positioning system data set from Columbus, Ohio. DCFC requirements supporting operation of EVs are estimated using the Electric Vehicle Infrastructure Projection tool. Operation and installation costs were estimated using real-world data to assess the economic feasibility of the recommended fast charging stations. Results suggest that the hypothetical transportation network company fleet increases daily vehicle miles traveled per EV with less overall down time, resulting in increased demand for DCFC. Sites with overhead service lines are recommended for hosting DCFC stations to minimize the need for trenching underground service lines. A negative relationship was found between cost per unit of energy and fast charging utilization, underscoring the importance of prioritizing utilization over installation costs when siting DCFC stations. Although this preliminary analysis of the impacts of new mobility paradigms on alternative fueling infrastructure requirements has produced several key results, the complexity of the problem warrants further investigation.

  7. The virtual library in action: Collaborative international control of high-energy physics pre-print

    International Nuclear Information System (INIS)

    Kreitz, P.A.; Addis, L.; Galic, H.; Johnson, T.

    1996-02-01

    This paper will discuss how control of the grey literature in high-energy physics pre-prints developed through a collaborative effort of librarians and physicists. It will highlight the critical steps in the development process and describe one model of a rapidly evolving virtual library for high-energy physics information. In conclusion, this paper will extend this physics model to other areas of grey literature management

  8. A Study of Stress Distribution in Layered and Gradient Tribological Coatings (Preprint)

    Science.gov (United States)

    2006-11-01

    FG) Ti/TiC coating design. On the top of the 440C stainless steel substrate, α-Ti is added as a bond layer with 50nm thickness to improve the... stainless steel substrate and the rigid spherical indenter was performed. Figure 5 (a) shows the normalized Hertzian point contact pressure distribution...AFRL-ML-WP-TP-2007-402 A STUDY OF STRESS DISTRIBUTION IN LAYERED AND GRADIENT TRIBOLOGICAL COATINGS (PREPRINT) Young Sup Kang, Shashi K

  9. PRODUCTION TECHNICS AT GRAPHIC DESIGN EDUCATION AND THE NECCESSITY OF PREPARATION KNOWLEDGE OF PRE-PRINTING

    OpenAIRE

    CEYLAN, İbrahim Gökhan

    2015-01-01

    It is neccessary to teach the knowledge of production technics and pre-printing preparations besides the knowledge of developing creativity and aesthetic concerns in order to educate the designers to fullfill the needs of the sector totally at graphic design education. The printed materials prepared by the graphic designer should be evaluated in proper criterias ıf the materials are to be printed. Graphic designers should have the knowledge of the required knowledge of the area in order to me...

  10. Customizable pre-printed consent forms: a solution in light of the Montgomery ruling.

    Science.gov (United States)

    Owen, Deborah; Aresti, Nick; Mulligan, Alex; Kosuge, Dennis

    2018-02-02

    This article presents an audit cycle supported quality improvement project addressing best practice in the consent process for lower limb arthroplasty which takes into account the new standard in surgical consent and the importance of material risks. 50 consecutive total hip and total knee replacement consent forms over a 3-month period were reviewed for legibility and completeness. Following the introduction of a new, pre-printed but customizable consent form the review process was repeated. The introduction of a customizable, pre-printed consent form that can be adjusted to reflect the individualized material risks of each patient increased legibility, reduced inappropriate human error variation and abolished the use of abbreviations and medical jargon. When used as part of an extended consent process, the authors feel that the use of pre-printed but customizable consent forms improves legibility, completeness and consistency and also provides the ability to highlight those complications that are of particular importance for that patient to satisfy the new accepted standard in surgical consent.

  11. Study of the Imidazolium-Based Ionic Liquid - ag Electrified Interface on the CO_{2} Electroreduction by Sum Frequency Spectroscopy.

    Science.gov (United States)

    Garcia Rey, Natalia; Dlott, Dana

    2017-06-01

    Imidazolium based ionic liquids (ILs) have been used as a promising system to improve the CO_{2} electroreduction at lower overpotential than other organic or aqueous electrolytes^{1}. Although the detailed mechanism of the CO_{2} electroreduction on Ag has not been elucidated yet, we have developed a methodology to study the electrified interface during the CO_{2} electroreduction using sum frequency generation (SFG) spectroscopy in combination with cyclic voltammetry^{2}. In this work, we tuned the composition of imidazolium-based ILs by exchanging the anion or the functional groups of the imidazolium. We use the nonresonant SFG (NR-SFG) to study the IL-Ag interface and resonant SFG (RES-SFG) to identify the CO adsorbed on the electrode and monitor the Stark shift as a function of cell potential. In previous studies on CO_{2} electroreduction in the IL: 1-ethyl-3-methylimidazolium tetrafluorborate (EMIM-BF_{4}) on Ag, we showed three events occurred at the same potential (-1.33 V vs. Ag/AgCl): the current associated with CO_{2} electroreduction increased, the Stark shift of the adsorbed atop CO doubled in magnitude and the EMIM-BF_{4} underwent a structural transition^{3}. In addition, we also observed how the structural transition of the EMIM-BF_{4} electrolyte shift to lower potentials when the IL is mixed with water. It is known that water enhances the CO_{2} electroreduction producing more CO^{4}. Moreover, the CO is adsorbed in multi-bonded and in atop sites when more water is present in the electrolyte. ^{1}Lau, G. P. S.; Schreier, M.; Vasilyev, D.; Scopelliti, R.; Grätzel, M.; Dyson, P. J., New Insights into the Role of Imidazolium-Based Promoters for the Electroreduction of CO_{2} on a Silver Electrode. J. Am. Chem. Soc. 2016, 138, 7820-7823. ^{2}Garcia Rey, N.; Dlott, D. D., Studies of Electrochemical Interfaces by Broadband Sum Frequency Generation. J. Electroanal. Chem. 2016. DOI:10.1016/j.jelechem.2016.12.023. ^{3}Garcia Rey, N.; Dlott, D. D

  12. A Modeling Study of the Spatial Structure of Electric Fields Generated by Electrified Clouds with Screening Layers

    Science.gov (United States)

    Biagi, C. J.; Cummins, K. L.

    2015-12-01

    The growing possibility of inexpensive airborne observations of electric fields using one or more small UAVs increases the importance of understanding what can be determined about cloud electrification and associated electric fields outside cloud boundaries. If important information can be inferred from carefully selected flight paths outside of a cloud, then the aircraft and its instrumentation will be much cheaper to develop and much safer to operate. These facts have led us to revisit this long-standing topic using quasi-static, finite-element modeling inside and outside arbitrarily shaped clouds with a variety of internal charge distributions. In particular, we examine the effect of screening layers on electric fields outside of electrified clouds by comparing modeling results for charged clouds having electrical conductivities that are both equal to and lower than the surrounding clear air. The comparisons indicate that the spatial structure of the electric field is approximately the same regardless of the difference in the conductivities between the cloud and clear air and the formation of a screening layer, even for altitude-dependent electrical conductivities. This result is consistent with the numerical modeling results reported by Driscoll et al [1992]. The similarity of the spatial structure of the electric field outside of clouds with and without a screening layer suggests that "bulk" properties related to cloud electrification might be determined using measurements of the electric field at multiple locations in space outside the cloud, particularly at altitude. Finally, for this somewhat simplified model, the reduction in electric field magnitude outside the cloud due to the presence of a screening layer exhibits a simple dependence on the difference in conductivity between the cloud and clear air. These results are particularly relevant for studying clouds that are not producing lightning, such as developing thunderstorms and decaying anvils

  13. A Weakest-Link Approach for Fatigue Limit of 30CrNiMo8 Steels (Preprint)

    Science.gov (United States)

    2011-03-01

    34Application of a Weakest-Link Concept to the Fatigue Limit of the Bearing Steel Sae 52100 in a Bainitic Condition," Fatigue and Fracture of...AFRL-RX-WP-TP-2011-4206 A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) S. Ekwaro-Osire and H.V. Kulkarni Texas...2011 4. TITLE AND SUBTITLE A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT

  14. Decarbonizing Sweden’s energy and transportation system by 2050

    Directory of Open Access Journals (Sweden)

    Rasmus Bramstoft

    2017-01-01

    Full Text Available Decarbonizing Sweden’s transportation sector is necessary to realize its long-term vision of eliminating net greenhouse gas (GHG emissions from the energy system by 2050. Within this context, this study develops two scenarios for the transportation sector: one with high electrification (EVS and the other with high biofuel and biomethane utilization (BIOS. The energy system model STREAM is utilized to compute the socioeconomic system cost and simulate an integrated transportation, electricity, gas, fuel refinery, and heat system. The results show that electrifying a high share of Sweden’s road transportation yields the least systems cost. However, in the least-cost scenario (EVS, bioenergy resources account for 57% of the final energy use in the transportation sector. Further, a sensitivity analysis shows that the costs of different types of cars are the most sensitive parameters in the comparative analysis of the scenarios.

  15. Decarbonizing Sweden’s energy and transportation system by 2050

    DEFF Research Database (Denmark)

    Bramstoft, Rasmus; Skytte, Klaus

    2017-01-01

    Decarbonizing Sweden’s transportation sector is necessary to realize its long-term vision of eliminating net greenhouse gas (GHG) emissions from the energy system by 2050. Within this context, this study develops two scenarios for the transportation sector: one with high electrification (EVS......) and the other with high biofuel and biomethane utilization (BIOS). The energy system model STREAM is utilized to compute the socioeconomic system cost and simulate an integrated transportation, electricity, gas, fuel refinery, and heat system. The results show that electrifying a high share of Sweden’s road...... transportation yields the least systems cost. However, in the least-cost scenario (EVS), bioenergy resources account for 57% of the final energy use in the transportation sector. Further, a sensitivity analysis shows that the costs of different types of cars are the most sensitive parameters in the comparative...

  16. Model-based design validation for advanced energy management strategies for electrified hybrid power trains using innovative vehicle hardware in the loop (VHIL) approach

    International Nuclear Information System (INIS)

    Mayyas, Abdel Ra'ouf; Kumar, Sushil; Pisu, Pierluigi; Rios, Jacqueline; Jethani, Puneet

    2017-01-01

    Highlights: •Vehicle hardware In-the-loop VHiL testing and validation is implemented in vehicle test bed. •Torque at the roller bench test is used to control the torque at wheels to reflect vehicle electrification symptoms. •Electrified powertrain with Equivalent Consumption Minimization Strategy is tested and validated using VHiL. •Fuel economy and power train performance is measured using high precision fuel measurement device. -- Abstract: Hybridization of automotive powertrains by using more than one type of energy converter is considered as an important step towards reducing fuel consumption and air pollutants. Specifically, the development of energy efficient, highly complex, alternative drive-train systems, in which the interactions of different energy converters play an important role, requires new design methods and processes. This paper discusses the inclusion of an alternative hybrid power train into an existing vehicle platform for maximum energy efficiency. The new proposed integrated Vehicle Hardware In-the-loop (VHiL) and Model Based Design (MBD) approach is utilized to evaluate the energy efficiency of electrified powertrain. In VHiL, a complete chassis system becomes an integrated part of the vehicle test bed. A complete conventional Internal Combustion Engine (ICE) powered vehicle is tested in roller bench test for the integration of energy efficient hybrid electric power train modules in closed-loop, real-time, feedback configuration. A model that is a replica of the test vehicle is executed – in real-time- where all hybrid power train modules are included. While the VHiL platform is controlling the signal exchange between the test bed automation software and the vehicle on-board controller, the road load exerted on the driving wheels is manipulated in closed –loop real-time manner in order to reflect all hybrid driving modes including: All Electric Range (AER), Electric Power Assist (EPA) and blended Modes (BM). Upon successful

  17. Hydrogen Pressurization of LOX: High Risk/High Reward (Preprint)

    National Research Council Canada - National Science Library

    Turner, Andrew E; Leichner, Aaron

    2006-01-01

    ... filled with hydrogen gas. Airship commercial service, enabled by relatively low-cost hydrogen, died along with the longest vehicle ever to fly, even though thousands of passengers had been transported without incident prior to that time...

  18. Constraint Preserving Schemes Using Potential-Based Fluxes. I. Multidimensional Transport Equations (PREPRINT)

    Science.gov (United States)

    2010-01-01

    i,j−∆t nEni ,j , u∗∗i,j =u ∗ i,j−∆t nEni ,j , un+1i,j = 1 2 (uni,j+u ∗∗ i,j ). (2.26) An alternative first-order accurate genuinely multi-dimensional...time stepping is the ex- tended Lax-Friedrichs type time stepping, un+1i,j = 1 8 (4uni,j+u n i+1,j+u n i,j+1+u n i−1,j+u n i,j−1)−∆t nEni ,j . (2.27) 13

  19. Note on: Considering the Case for Biodiversity Cycles: Reexamining the Evidence for Periodicity in the Fossil Record, by Lieberman and Melott, arXiv preprint 0704.2896

    OpenAIRE

    Omerbashich, M.

    2007-01-01

    Lieberman and Melott built their recent arXiv preprint 0704.2896 on my published paper and (a preprint of) a subsequent comment by Liebermans associate Cornette. But had this group waited for the Cornette comment to actually appear in print together with the expected Reply, they would have learned that his comment exposes Cornettes confusion that likely was due to journal misprint of my figure. Thus 0704.2896 is baseless. Despite receiving the extended Reply with Errata, these authors still f...

  20. Electricity as Transportation ``Fuel''

    Science.gov (United States)

    Tamor, Michael

    2013-04-01

    The personal automobile is a surprisingly efficient device, but its place in a sustainable transportation future hinges on its ability use a sustainable fuel. While electricity is widely expected to be such a ``fuel,'' the viability of electric vehicles rests on the validity of three assumptions. First, that the emissions from generation will be significantly lower than those from competing chemical fuels whether `renewable' or fossil. Second, that advances in battery technology will deliver adequate range and durability at an affordable cost. Third, that most customers will accept any functional limitations intrinsic to electrochemical energy storage. While the first two are subjects of active research and vigorous policy debate, the third is treated virtually as a given. Popular statements to the effect that ``because 70% of all daily travel is accomplished in less than 100 miles, mass deployment of 100 mile EVs will electrify 70% of all travel'' are based on collections of one-day travel reports such as the National Household Travel Survey, and so effectively ignore the complexities of individual needs. We have analyzed the day-to-day variations of individual vehicle usage in multiple regions and draw very different conclusions. Most significant is that limited EV range results in a level of inconvenience that is likely to be unacceptable to the vast majority of vehicle owners, and for those who would accept that inconvenience, battery costs must be absurdly low to achieve any economic payback. In contrast, the plug-in hybrid (PHEV) does not suffer range limitations and delivers economic payback for most users at realistic battery costs. More importantly, these findings appear to be universal in developed nations, with labor market population density being a powerful predictor of personal vehicle usage. This ``scalable city'' hypothesis may prove to a powerful predictor of the evolution of transportation in the large cities of the developing world.

  1. Solar Decathlon: Collegiate Challenge to Build the Future; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Warner, C.; King, R.; Nahan, R.; Eastment, M.

    2002-05-01

    A new collegiate competition, called the Solar Decathlon, is under way. Fourteen teams from colleges and universities across the United States, including Puerto Rico, will assemble on the National Mall in Washington, DC, in late September 2002. They will compete to capture, convert, store, and use enough solar energy to power small, solar-powered, energy-efficient homes that they have designed, built, and transported to the site. Solar Decathletes will be required to provide all the energy for an entire household, including a home-based business and the transportation needs of the household and business. During the event, only the solar energy available within the perimeter of each house may be used to generate the power needed to compete in the ten Solar Decathlon contests. The event is sponsored by the U.S. Department of Energy, National Renewable Energy Laboratory, and private-sector partners BP Solar, American Institute of Architects, Electronic Data Systems, and Home Depot.

  2. CELLS v1.0: updated and parallelized version of an electrical scheme to simulate multiple electrified clouds and flashes over large domains

    Directory of Open Access Journals (Sweden)

    C. Barthe

    2012-01-01

    Full Text Available The paper describes the fully parallelized electrical scheme CELLS which is suitable to simulate explicitly electrified storm systems on parallel computers. Our motivation here is to show that a cloud electricity scheme can be developed for use on large grids with complex terrain. Large computational domains are needed to perform real case meteorological simulations with many independent convective cells.

    The scheme computes the bulk electric charge attached to each cloud particle and hydrometeor. Positive and negative ions are also taken into account. Several parametrizations of the dominant non-inductive charging process are included and an inductive charging process as well. The electric field is obtained by inverting the Gauss equation with an extension to terrain-following coordinates. The new feature concerns the lightning flash scheme which is a simplified version of an older detailed sequential scheme. Flashes are composed of a bidirectional leader phase (vertical extension from the triggering point and a phase obeying a fractal law (with horizontal extension on electrically charged zones. The originality of the scheme lies in the way the branching phase is treated to get a parallel code.

    The complete electrification scheme is tested for the 10 July 1996 STERAO case and for the 21 July 1998 EULINOX case. Flash characteristics are analysed in detail and additional sensitivity experiments are performed for the STERAO case. Although the simulations were run for flat terrain conditions, they show that the model behaves well on multiprocessor computers. This opens a wide area of application for this electrical scheme with the next objective of running real meterological case on large domains.

  3. Establishing a Secure Data Center with Remote Access: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Gonder, J.; Burton, E.; Murakami, E.

    2012-04-01

    Access to existing travel data is critical for many analysis efforts that lack the time or resources to support detailed data collection. High-resolution data sets provide particular value, but also present a challenge for preserving the anonymity of the original survey participants. To address this dilemma of providing data access while preserving privacy, the National Renewable Energy Laboratory and the U.S. Department of Transportation have launched the Transportation Secure Data Center (TSDC). TSDC data sets include those from regional travel surveys and studies that increasingly use global positioning system devices. Data provided by different collecting agencies varies with respect to formatting, elements included and level of processing conducted in support of the original purpose. The TSDC relies on a number of geospatial and other analysis tools to ensure data quality and to generate useful information outputs. TSDC users can access the processed data in two different ways. The first is by downloading summary results and second-by-second vehicle speed profiles (with latitude/longitude information removed) from a publicly-accessible website. The second method involves applying for a remote connection account to a controlled-access environment where spatial analysis can be conducted, but raw data cannot be removed.

  4. Rethinking the Future Grid: Integrated Nuclear Renewable Energy Systems: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Bragg-Sitton, S. M.; Boardman, R.; Ruth, M.; Zinaman, O.; Forsberg, C.

    2015-01-01

    The U.S. DOE is supporting research and development that could lead to more efficient utilization of clean energy generation sources, including renewable and nuclear options, to meet both grid demand and thermal energy needs in the industrial sector. One concept under consideration by the DOE-NE and DOE-EERE is tighter coupling of nuclear and renewable energy sources in a manner that better optimizes energy use for the combined electricity, industrial manufacturing, and transportation sectors. This integration concept has been referred to as a 'hybrid system' that is capable of apportioning thermal and electrical energy to first meet the grid demand (with appropriate power conversion systems), then utilizing excess thermal and, in some cases, electrical energy to drive a process that results in an additional product.

  5. National symposium on commissioning and operating experiences in heavy water plants and associated chemical industries [Preprint volume

    International Nuclear Information System (INIS)

    1992-02-01

    A symposium on commissioning and operating experiences in heavy water plants and associated chemical industries (SCOPEX-92) was organised to share the experience and exchange the ideas among plant operators, designers, consultants and vendors in the areas of operation, commissioning and equipment performance. This pre-print volume has been brought out as an integrated source of information on commissioning and operation of heavy water plants. The following aspects of heavy water plants are covered: commissioning and operation, instrumentation and control, and safety and environment. (V.R.)

  6. Status of Wind-Diesel Applications in Arctic Climates: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Baring-Gould, I.; Corbus, D.

    2007-12-01

    The rising cost of diesel fuel and the environmental regulation for its transportation, use, and storage, combined with the clear impacts of increased arctic temperatures, is driving remote communities to examine alternative methods of providing power. Over the past few years, wind energy has been increasingly used to reduce diesel fuel consumption, providing economic, environmental, and security benefits to the energy supply of communities from Alaska to Antarctica. This summary paper describes the current state of wind-diesel systems, reviews the operation of wind-diesel plants in cold climates, discusses current research activities pertaining to these systems, and addresses their technical and commercial challenges. System architectures, dispatch strategies, and operating experience from a variety of wind-diesel systems in Alaska will be reviewed. Specific focus will also be given to the control of power systems with large amounts of wind generation and the complexities of replacing diesel engine waste heat with excess wind energy, a key factor in assessing power plants for retrofit. A brief overview of steps for assessing the viability of retrofitting diesel power systems with wind technologies will also be provided. Because of the large number of isolated diesel minigrids, the market for adding wind to these systems is substantial, specifically in arctic climates and on islands that rely on diesel-only power generation.

  7. Metallic Nanocomposites as Next-Generation Thermal Interface Materials: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Xuhui [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Narumanchi, Sreekant V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); King, Charles C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Nagabandi, Nirup [Texas A& M University; Oh, Jun K. [Texas A& M University; Akbulut, Mustafa [Texas A& M University; Yegin, Cengiz [Texas A& M University

    2017-09-14

    Thermal interface materials (TIMs) are an integral and important part of thermal management in electronic devices. The electronic devices are becoming more compact and powerful. This increase in power processed or passing through the devices leads to higher heat fluxes and makes it a challenge to maintain temperatures at the optimal level during operation. Herein, we report a free standing nanocomposite TIM in which boron nitride nanosheets (BNNS) are uniformly dispersed in copper matrices via an organic linker, thiosemicarbazide. Integration of these metal-organic-inorganic nanocomposites was made possible by a novel electrodeposition technique where the functionalized BNNS (f-BNNS) experience the Brownian motion and reach the cathode through diffusion, while the nucleation and growth of the copper on the cathode occurs via the electrochemical reduction. Once the f-BNNS bearing carbonothioyl/thiol groups on the terminal edges come into the contact with copper crystals, the chemisorption reaction takes place. We performed thermal, mechanical, and structural characterization of these nanocomposites using scanning electron microcopy (SEM), diffusive laser flash (DLF) analysis, phase-sensitive transient thermoreflectence (PSTTR), and nanoindentation. The nanocomposites exhibited a thermal conductivity ranging from 211 W/mK to 277 W/mK at a filler mass loading of 0-12 wt.percent. The nanocomposites also have about 4 times lower hardness as compared to copper, with values ranging from 0.27 GPa to 0.41 GPa. The structural characterization studies showed that most of the BNNS are localized at grain boundaries - which enable efficient thermal transport while making the material soft. PSTTR measurements revealed that the synergistic combinations of these properties yielded contact resistances on the order of 0.10 to 0.13 mm2K/W, and the total thermal resistance of 0.38 to 0.56 mm2K/W at bondline thicknesses of 30-50 um. The coefficient of thermal expansion (CTE) of the

  8. Coupled Dynamic Modeling of Floating Wind Turbine Systems: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wayman, E. N.; Sclavounos, P. D.; Butterfield, S.; Jonkman, J.; Musial, W.

    2006-03-01

    the two concepts was also performed. Key cost components included the material and construction costs of the buoy; material and installation costs of the tethers, mooring lines, and anchor technologies; costs of transporting and installing the system at the chosen site; and the cost of mounting the wind turbine to the platform. The two systems were evaluated based on their static and dynamic performance and the total system installed cost. Both systems demonstrated acceptable motions, and have estimated costs of $1.4-$1.8 million, not including the cost of the wind turbine, the power electronics, or the electrical transmission.

  9. Transport Statistics - Transport - UNECE

    Science.gov (United States)

    Sustainable Energy Statistics Trade Transport Themes UNECE and the SDGs Climate Change Gender Ideas 4 Change UNECE Weekly Videos UNECE Transport Areas of Work Transport Statistics Transport Transport Statistics About us Terms of Reference Meetings and Events Meetings Working Party on Transport Statistics (WP.6

  10. Preprints in biomedicine: alternative or complement to the traditional model of publication?

    Science.gov (United States)

    Aquino-Jarquin, Guillermo; Valencia-Reyes, Josefina de Monserrat; Silva-Carmona, Abraham; Granados-Riverón, Javier Tadeo

    2018-01-01

    The peer-review system has allowed the quality control of the manuscripts submitted for publication to scientific journals for over three centuries. However, due to its relative slowness and other drawbacks, some researchers, mainly in the areas of Physics and Mathematics, started some decades ago to propagate, by electronic means, manuscripts not yet submitted to a journal for formal publication. The dissemination of this practice led to the establishment of permanent repositories like ArXiv, to which preprints can be sent to be published whitou charge, allowing also the search and download of the works they contain with no payment required from the reader. In biomedical sciences, the adoption of the system has been slower than in the exact sciences and previous attempts like e-biomed, Netprints, and Nature Precedings did not prosper. A new generation of repositories like bioRXiv, inspired by ArXiv, seems to enjoy an increasing acceptance among biomedical researchers. Here, we discuss the potential role of this emerging system to establish discovery priority in biomedicine and to improve manuscripts before they are submitted to scientific journals besides other applications which could be implemented in the extent that the model becomes more popular. Copyright: © 2018 SecretarÍa de Salud.

  11. Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Saxon, Aron R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Keyser, Matthew A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lundstrom, Blake R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cao, Ziwei [SunPower Corporation; Roc, Albert [SunPower Corp.

    2017-08-25

    Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System: Preprint Lithium-ion (Li-ion) batteries are being deployed on the electrical grid for a variety of purposes, such as to smooth fluctuations in solar renewable power generation. The lifetime of these batteries will vary depending on their thermal environment and how they are charged and discharged. To optimal utilization of a battery over its lifetime requires characterization of its performance degradation under different storage and cycling conditions. Aging tests were conducted on commercial graphite/nickel-manganese-cobalt (NMC) Li-ion cells. A general lifetime prognostic model framework is applied to model changes in capacity and resistance as the battery degrades. Across 9 aging test conditions from 0oC to 55oC, the model predicts capacity fade with 1.4 percent RMS error and resistance growth with 15 percent RMS error. The model, recast in state variable form with 8 states representing separate fade mechanisms, is used to extrapolate lifetime for example applications of the energy storage system integrated with renewable photovoltaic (PV) power generation.

  12. Potential benefits of superconductivity to transportation in the United States

    Science.gov (United States)

    Rote, Donald M.; Johnson, Larry R.

    Research in U.S. transportation applications of superconductors is strongly motivated by a number of potential national benefits. These include the reduction of dependence on petroleum-based fuels, energy savings, substantially reduced air and noise pollution, increased customer convenience, and reduced maintenance costs. Current transportation technology offers little flexibility to switch to alternative fuels, and efforts to achieve the other benefits are confounded by growing congestion at airports and on urban roadways. A program has been undertaken to identify possible applications of the emerging superconducting applications to transportation and to evaluate potential national benefits. The current phase of the program will select the most promising applications for a more detailed subsequent study. Transportation modes being examined include highway and industrial vehicles, as well as rail, sea, air transport and pipelines. Three strategies are being considered: (1) replacing present components with those employing superconductors, (2) substituting new combinations of components or systems for present systems, and (3) developing completely new technologies. Distinctions are made between low-, medium-, and near-room-temperature superconductors. The most promising applications include magnetically levitated passenger and freight vehicles; replacement of drive systems in locomotives, self-propelled rail cars, and ships; and electric vehicles inductively coupled to electrified roadways.

  13. Feasibility of implementation of an autonomous hybrid system for PEM fuel cells to electrify localities in rural Cuba; Factibilidad de implementacion de un sistema hibrido autonomo con celda de combustible PEM para electrificar localidades rurales en Cuba

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez Torres, Yamir [Centro de Estudios de Tecnologias Energeticas Renovables (CETER), Ciudad de la Habana (Cuba)] e-mail: yamir@ceter.cujae.edu.cu

    2009-09-15

    The use of PEM fuel cells to produce electric energy in autonomous systems is closely linked with the production and storage of hydrogen. Eventually joined with sources of renewable energy, this creates an ecologically clean and sustainable system. In several developing countries, localities exist that do not have electricity but have significant unexploited renewable energy power, where an autonomous hybrid system can be designed to electrify these population centers. This work presents a hybrid electricity scheme with a PEM fuel cell to produce hydrogen and electricity in order to electrify rural zones far from the national power grid in Cuba. The electric demand of the zone and available energy power was calculated using the informatics modeling and simulation programs HOMER, PVSYST and Matlab 1,2,3. Variability in wind and photovoltage power was determined based on daylight hours and seasonal periods throughout the year as well as their effect on the production of hydrogen and electricity. It was shown that the energy demand is met even for the most adverse scenarios. This work offers a detailed description of the behavior of the system and evidence of no effect on the environment, enabling the electrification and wellbeing of residents of the locality. [Spanish] El uso de celdas de combustible PEM para la produccion de energia electrica en sistemas autonomos esta estrechamente ligado a la produccion y almacenamiento de hidrogeno. Esto eventualmente unido a las fuentes renovables de energia forma un sistema ecologicamente limpio y sustentable. En varios paises subdesarrollados existen localidades que no cuentan con electricidad y que tienen importantes potenciales energeticos renovables no explotados actualmente en los cuales se puede disenar un sistema hibrido autonomo para electrificar estas poblaciones. En este trabajo se presenta el esquema de un sistema hibrido autonomo con celda de combustible PEM, para la produccion de hidrogeno y electricidad encaminado

  14. Preprints na comunicação científica da Física de Altas Energias: análise das submissões no repositório arXiv (2010-2015

    Directory of Open Access Journals (Sweden)

    Gonzalo Rubén Alvarez

    Full Text Available RESUMO A circulação de preprints na Física de Altas Energias (FAE remonta a mais de meio século, tendo como objetivos principais acelerar o processo de comunicação científica entre os pares e estimular o acesso livre à literatura especializada da área. O artigo analisa o conjunto de preprints submetidos às diferentes categorias FAE do repositório temático especializado arXiv no período 2010-2015 que foram posteriormente publicados em revistas peer review. Os indicadores bibliométricos demonstram a potencialidade dos preprints como canal precursor de difusão de resultados científicos visto que 70% das submissões foram em seguida absorvidas pelas principais revistas da FAE. Conclui que o êxito alcançado pelas iniciativas Open Access arXiv e INSPIRE-HEP favoreceu o intercâmbio de informações e conhecimentos entre os pesquisadores. O modelo proposto pela FAE pode incentivar cientistas de áreas com características similares a instalarem repositórios e bancos de dados de preprints para suas disciplinas com o intuito de fortalecer a comunicação das descobertas científicas.

  15. Pathways to a more sustainable transport infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Dravitzki, V., Email: Vince.Dravitzki@Opus.co.nz; Lester, T.; Cenek, P. [Opus International Consultants, Lower Hutt (New Zealand)

    2010-07-01

    The two phenomena of Peak Oil and Human-induced Climate Change both together and individually create an imperative for early action, with the need to address Climate Change limiting the range of options that can be used to address peak oil. Peak oil is often portrayed as a market phenomenon, as a period when demand will exceed supply. The imperative to respond to the issues resulting from Peak Oil and Climate Change requires that New Zealand must move from its current high energy use, high resource use, high cost, petroleum dependent, transport infrastructure, to a sustainable one. Because a country's energy profile will increasingly define its economic success, New Zealand needs also to move to a lower energy society to remain competitive with other countries. What will be New Zealand's successful transport energy of the future and how it may be best used are key considerations of our future sustainable transport system. Low energy, low material use and consequently low cost, will be the main criteria. This paper first identifies our current transport energy usage, and some of the risks of being slow to respond to change. The paper then questions the central tenants of the current New Zealand Land Transport Strategy (2008) that we move to bio-fuels and electric cars because this is not a low energy, low cost pathway. We advocate that instead of just coping with change, New Zealand uses the necessity to change as an opportunity to recast our transport infrastructure to greatly improve the economic success and liveability of our settlements to New Zealand's benefit. The second part of the paper outlines a transport infrastructure based around electricity, with a heavy emphasis on public transport use, but also with freight much more dependent on electrified rail. This second part discusses: the advantages that NZ has that will facilitate this transition, such as favourable urban forms; the energy needs and energy availability; the benefits and

  16. A Hybrid Dynamic System Assessment Methodology for Multi-Modal Transportation-Electrification

    Directory of Open Access Journals (Sweden)

    Thomas J.T. van der Wardt

    2017-05-01

    Full Text Available In recent years, electrified transportation, be it in the form of buses, trains, or cars have become an emerging form of mobility. Electric vehicles (EVs, especially, are set to expand the amount of electric miles driven and energy consumed. Nevertheless, the question remains as to whether EVs will be technically feasible within infrastructure systems. Fundamentally, EVs interact with three interconnected systems: the (physical transportation system, the electric power grid, and their supporting information systems. Coupling of the two physical systems essentially forms a nexus, the transportation-electricity nexus (TEN. This paper presents a hybrid dynamic system assessment methodology for multi-modal transportation-electrification. At its core, it utilizes a mathematical model which consists of a marked Petri-net model superimposed on the continuous time microscopic traffic dynamics and the electrical state evolution. The methodology consists of four steps: (1 establish the TEN structure; (2 establish the TEN behavior; (3 establish the TEN Intelligent Transportation-Energy System (ITES decision-making; and (4 assess the TEN performance. In the presentation of the methodology, the Symmetrica test case is used throughout as an illustrative example. Consequently, values for several measures of performance are provided. This methodology is presented generically and may be used to assess the effects of transportation-electrification in any city or area; opening up possibilities for many future studies.

  17. Electric Road Systems: Strategic Stepping Stone on the Way towards Sustainable Freight Transport?

    Directory of Open Access Journals (Sweden)

    Jesko Schulte

    2018-04-01

    Full Text Available Electrification of the transport sector has been pointed out as a key factor for tackling some of today’s main challenges, such as global warming, air pollution, and eco-system degradation. While numerous studies have investigated the potential of electrifying passenger transport, less focus has been on how road freight transport could be powered in a sustainable future. This study looks at Electric Road Systems (ERS in comparison to the current diesel system. The Framework for Strategic Sustainable Development was used to assess whether ERS could be a stepping stone on the way towards sustainability. Strategic life-cycle assessment was applied, scanning each life-cycle phase for violations against basic sustainability principles. Resulting sustainability “hot spots” were quantified with traditional life-cycle assessment. The results show that, if powered by renewable energy, ERS have a potential to decrease the environmental impact of freight transport considerably. Environmental payback times of less than five years are achievable if freight traffic volumes are sufficiently high. However, some severe violations against sustainability principles were identified. Still, ERS could prove to be a valuable part of the solution, as they drastically decrease the need for large batteries with high cost and sustainability impact, thereby catalyzing electrification and the transition towards sustainable freight transport.

  18. Energy efficiency development possibilities in public transport; Joukkoliikenteen energiatehokkuuden kehittaemismahdollisuudet

    Energy Technology Data Exchange (ETDEWEB)

    Korteniemi, J.; Pasanen, P.; Latvala, M.; Pohjola, T. (Bionova Consulting, Helsinki (Finland))

    2010-10-15

    transporting one person 1,3 km. From CO{sub 2} emissions point of view metro, train and tramway deliver best results due to low consumption and electrical drive. Public transport has a major role in reducing energy consumption and greenhouse gas emissions. By the year 2020 the efficiency improvements are mostly based in the adoption of hybrid buses, increasing the share of electrified public transport, and increasing the share of biofuels. From the operational measures the most important are economic driving training and increased utilisation of braking energy. However, the greatest impact of public transport is at the transport system level. (orig.)

  19. Radiation Transport

    Energy Technology Data Exchange (ETDEWEB)

    Urbatsch, Todd James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-06-15

    We present an overview of radiation transport, covering terminology, blackbody raditation, opacities, Boltzmann transport theory, approximations to the transport equation. Next we introduce several transport methods. We present a section on Caseology, observing transport boundary layers. We briefly broach topics of software development, including verification and validation, and we close with a section on high energy-density experiments that highlight and support radiation transport.

  20. Chamber transport

    International Nuclear Information System (INIS)

    Olson, Craig L.

    2001-01-01

    Heavy ion beam transport through the containment chamber plays a crucial role in all heavy ion fusion (HIF) scenarios. Here, several parameters are used to characterize the operating space for HIF beams; transport modes are assessed in relation to evolving target/accelerator requirements; results of recent relevant experiments and simulations of HIF transport are summarized; and relevant instabilities are reviewed. All transport options still exist, including (1) vacuum ballistic transport, (2) neutralized ballistic transport, and (3) channel-like transport. Presently, the European HIF program favors vacuum ballistic transport, while the US HIF program favors neutralized ballistic transport with channel-like transport as an alternate approach. Further transport research is needed to clearly guide selection of the most attractive, integrated HIF system

  1. Energy Storage Publications | Transportation Research | NREL

    Science.gov (United States)

    , California. 23 pp.; NREL Report No. PR-5400-60290. Optimal Sizing of Energy Storage and Photovoltaic Power (11) 2017 pp. 1095-1118. Life Prediction Model for Grid-Connected Li-ion Battery Energy Storage System Prediction Model for Grid-Connected Li-ion Battery Energy Storage System - Preprint Paper Source: Smith

  2. Transport phenomena

    International Nuclear Information System (INIS)

    Kirczenow, G.; Marro, J.

    1974-01-01

    Some simple remarks on the basis of transport theory. - Entropy, dynamics and scattering theory. - Response, relaxation and fluctuation. - Fluctuating hydrodynamics and renormalization of susceptibilities and transport coefficients. - Irreversibility of the transport equations. - Ergodic theory and statistical mechanics. - Correlation functions in Heisenberg magnets. - On the Enskog hard-sphere kinetic eqquation and the transport phenomena of dense simple gases. - What can one learn from Lorentz models. - Conductivity in a magnetic field. - Transport properties in gases in presence of external fields. - Transport properties of dilute gases with internal structure. (orig.) [de

  3. Neurotransmitter transporters

    DEFF Research Database (Denmark)

    Gether, Ulrik; Andersen, Peter H; Larsson, Orla M

    2006-01-01

    The concentration of neurotransmitters in the extracellular space is tightly controlled by distinct classes of membrane transport proteins. This review focuses on the molecular function of two major classes of neurotransmitter transporter that are present in the cell membrane of neurons and....... Recent research has provided substantial insight into the structure and function of these transporters. In particular, the recent crystallizations of bacterial homologs are of the utmost importance, enabling the first reliable structural models of the mammalian neurotransmitter transporters...

  4. Modeling the electrified solid-liquid interface

    DEFF Research Database (Denmark)

    Rossmeisl, Jan; Skulason, Egill; Björketun, Mårten

    2008-01-01

    function can be related directly to the potential scale of the normal hydrogen electrode. We also show how finite-size effects in common periodic slab-type calculations can be avoided in calculations of activation energies and reaction energies for charge transfer reactions, where we use the Heyrovsky......A detailed atomistic model based on density functional theory calculations is presented of the charged solid-electrolyte interface. Having protons solvated in a water bilayer outside a Pt(111) slab with excess electrons, we show how the interface capacitance is well described and how the work...

  5. Concealed semantic and episodic autobiographical memory electrified.

    Science.gov (United States)

    Ganis, Giorgio; Schendan, Haline E

    2012-01-01

    Electrophysiology-based concealed information tests (CIT) try to determine whether somebody possesses concealed information about a crime-related item (probe) by comparing event-related potentials (ERPs) between this item and comparison items (irrelevants). Although the broader field is sometimes referred to as "memory detection," little attention has been paid to the precise type of underlying memory involved. This study begins addressing this issue by examining the key distinction between semantic and episodic memory in the autobiographical domain within a CIT paradigm. This study also addresses the issue of whether multiple repetitions of the items over the course of the session habituate the brain responses. Participants were tested in a 3-stimulus CIT with semantic autobiographical probes (their own date of birth) and episodic autobiographical probes (a secret date learned just before the study). Results dissociated these two memory conditions on several ERP components. Semantic probes elicited a smaller frontal N2 than episodic probes, consistent with the idea that the frontal N2 decreases with greater pre-existing knowledge about the item. Likewise, semantic probes elicited a smaller central N400 than episodic probes. Semantic probes also elicited a larger P3b than episodic probes because of their richer meaning. In contrast, episodic probes elicited a larger late positive complex (LPC) than semantic probes, because of the recent episodic memory associated with them. All these ERPs showed a difference between probes and irrelevants in both memory conditions, except for the N400, which showed a difference only in the semantic condition. Finally, although repetition affected the ERPs, it did not reduce the difference between probes and irrelevants. These findings show that the type of memory associated with a probe has both theoretical and practical importance for CIT research.

  6. Concealed semantic and episodic autobiographical memory electrified

    Directory of Open Access Journals (Sweden)

    Giorgio eGanis

    2013-01-01

    Full Text Available Electrophysiology-based concealed information tests (CIT try to determine whether somebody possesses concealed information about a probe item by comparing event-related potentials (ERPs between this item and comparison items (irrelevants. Although the broader field is sometimes referred to as memory detection, little attention has been paid to the precise type of underlying memory involved. This study begins addressing this issue by examining the key distinction between semantic and episodic memory in the autobiographical domain within a CIT paradigm. This study also addressed the issue of whether multiple repetitions of the items over the course of the session habituate the brain responses. Participants were tested in a 3-stimulus CIT with semantic autobiographical probes (their own date of birth and episodic autobiographical probes (a secret date learned just before the study. Results dissociated these two memory conditions on several ERP components. Semantic probes elicited a smaller frontal N2 than episodic probes, consistent with the idea that the frontal N2 decreases with greater pre-existing semantic knowledge about the item. Likewise, semantic probes elicited a smaller central N400 than episodic probes. Semantic probes also elicited a larger P3b than episodic probes because of their richer meaning. In contrast, episodic probes elicited a larger late positive component (LPC than semantic probes, because of the recent episodic memory associated with them. All these ERPs showed a difference between probes and irrelevants in both memory conditions, except for the N400, which showed a difference only in the semantic condition. Finally, although repetition affected the ERPs, it did not reduce the difference between probes and irrelevants. Thus, the type of memory associated with a probe has both theoretical and practical importance for CIT research.

  7. Electrifying Greece with solar and wind energy

    Directory of Open Access Journals (Sweden)

    Mentis Dimitris

    2014-01-01

    Full Text Available Ensuring energy security, reducing GHG emissions and boosting the competitiveness of a country’s economy by attracting investments and technical knowhow are of paramount importance considering the targets of “20-20-20” set by the European community. Being the cradle of civilization, Greece appears today as a country caught in a prolonged hard economic and social crisis, the way out of which its citizens are looking forward as well as the entire European Union. Establishment of the leading renewable energy sources like solar and wind in Greece will not only increase the independence of its own electrification but will also provide with a foundation for developing the market of international trade of “green” energy. This paper initially highlights the current status of photovoltaics and wind turbines in Greece. Furthermore, this study evaluates whether a higher penetration of the above mentioned green energy sources would have positive impact in the economy of the country or not and in what extent they could decline the CO2 emissions until 2020, comparing to the corresponding levels in 2010.

  8. Concealed semantic and episodic autobiographical memory electrified

    Science.gov (United States)

    Ganis, Giorgio; Schendan, Haline E.

    2013-01-01

    Electrophysiology-based concealed information tests (CIT) try to determine whether somebody possesses concealed information about a crime-related item (probe) by comparing event-related potentials (ERPs) between this item and comparison items (irrelevants). Although the broader field is sometimes referred to as “memory detection,” little attention has been paid to the precise type of underlying memory involved. This study begins addressing this issue by examining the key distinction between semantic and episodic memory in the autobiographical domain within a CIT paradigm. This study also addresses the issue of whether multiple repetitions of the items over the course of the session habituate the brain responses. Participants were tested in a 3-stimulus CIT with semantic autobiographical probes (their own date of birth) and episodic autobiographical probes (a secret date learned just before the study). Results dissociated these two memory conditions on several ERP components. Semantic probes elicited a smaller frontal N2 than episodic probes, consistent with the idea that the frontal N2 decreases with greater pre-existing knowledge about the item. Likewise, semantic probes elicited a smaller central N400 than episodic probes. Semantic probes also elicited a larger P3b than episodic probes because of their richer meaning. In contrast, episodic probes elicited a larger late positive complex (LPC) than semantic probes, because of the recent episodic memory associated with them. All these ERPs showed a difference between probes and irrelevants in both memory conditions, except for the N400, which showed a difference only in the semantic condition. Finally, although repetition affected the ERPs, it did not reduce the difference between probes and irrelevants. These findings show that the type of memory associated with a probe has both theoretical and practical importance for CIT research. PMID:23355816

  9. Electrifying microbes for the production of chemicals

    Directory of Open Access Journals (Sweden)

    Pier-Luc eTremblay

    2015-03-01

    Full Text Available Powering microbes with electrical energy to produce valuable chemicals such as biofuels has recently gained traction as a biosustainable strategy to reduce our dependence on oil. Microbial electrosynthesis (MES is one of the bioelectrochemical approaches developed in the last decade that could have critical impact on the current methods of chemical synthesis. MES is a process in which electroautotrophic microbes use electrical current as electron source to reduce CO2 to multicarbon organics. Electricity necessary for MES can be harvested from renewable resources such as solar energy, wind turbine or wastewater treatment processes. The net outcome is that renewable energy is stored in the covalent bonds of organic compounds synthesized from greenhouse gas. This review will discuss the future of MES and the challenges that lie ahead for its development into a mature technology.

  10. Electrifying microbes for the production of chemicals

    DEFF Research Database (Denmark)

    Tremblay, Pier-Luc; Zhang, Tian

    2015-01-01

    have critical impact on the current methods of chemical synthesis. MES is a process in which electroautotrophic microbes use electrical current as electron source to reduce CO2 to multicarbon organics. Electricity necessary for MES can be harvested from renewable resources such as solar energy, wind......Powering microbes with electrical energy to produce valuable chemicals such as biofuels has recently gained traction as a biosustainable strategy to reduce our dependence on oil. Microbial electrosynthesis (MES) is one of the bioelectrochemical approaches developed in the last decade that could...... turbine, or wastewater treatment processes. The net outcome is that renewable energy is stored in the covalent bonds of organic compounds synthesized from greenhouse gas. This review will discuss the future of MES and the challenges that lie ahead for its development into a mature technology....

  11. Sustainable Transportation

    DEFF Research Database (Denmark)

    Hall, Ralph P.; Gudmundsson, Henrik; Marsden, Greg

    2014-01-01

    The transportation system is the backbone of economic and social progress and the means by which humans access goods and services and connect with one another. Yet, as the scale of transportation activities has grown worldwide, so too have the negative environmental, social, and economic impacts...... that relate to the construction and maintenance of transportation infrastructure and the operation or use of the different transportation modes. The concept of sustainable transportation emerged in response to these concerns as part of the broader notion of sustainable development. Given the transportation...... sector’s significant contribution to global challenges such as climate change, it is often said that sustainable development cannot be achieved without sustainable transportation....

  12. Light duty vehicle transportation and global climate policy: The importance of electric drive vehicles

    International Nuclear Information System (INIS)

    Bosetti, Valentina; Longden, Thomas

    2013-01-01

    With a focus on the interaction between long-term climate targets and personal transport we review the electrification of light duty vehicles (LDVs) within a model that utilizes a learning-by-researching structure. By modeling the demand of vehicles, the use of fuels and emissions implied, the model solves for the optimum RD and D investments that decrease the cost of hybrid, plug-in hybrid and electric vehicles. A range of technology and climate policy scenarios provide long term projections of vehicle use that highlight the potential synergies between innovation in the transportation sector and the energy sector. We find that even when the capital cost of electric drive vehicles (EDVs) remains higher than that of traditional combustion engine alternatives, EDVs are likely to play a key role in the decarbonisation implied by stringent climate policy. Limited innovation in batteries results in notable increases in policy costs consistent with a two degree climate policy target. - Highlights: • Significant increase in vehicles across regions in the medium to long term future. • Climate policy costs are sensitive to a lack of electric drive vehicles (EDVs). • Achieving 450ppm with no change in battery costs has a policy cost that is 2.86 percentage points higher than the base 450ppm scenario. • Climate policy hastens the introduction of electrified vehicles, however EDVs do not become the dominant vehicle of choice before the middle of the century

  13. Nuclear transport

    International Nuclear Information System (INIS)

    Anon.

    2003-01-01

    During january and february 2003, a unique event concerning nuclear transport was reported and rated 1 on the INES scale. This event concerns the absence of a maintenance operation on a shipping cask. This shipping cask was used for several years for nuclear transport inside La-hague site before being re-assigned to transport on public thoroughfare. The re-assignment of the cask should have been preceded and conditioned by a maintenance operation whose purpose is to check the efficiency of its radiation shield. During this period 2 on-site inspections concerning the transport of nuclear materials were performed. (A.C.)

  14. Ocean transportation

    National Research Council Canada - National Science Library

    Frankel, Ernst G; Marcus, Henry S

    1973-01-01

    .... This analysis starts with a review of ocean transportation demand and supply including projections of ship capacity demand and world shipbuilding capacity under various economic and political assumptions...

  15. Thermal transport studies using extreme ultraviolet spectroscopy: Final technical report, 5 March 1986-30 June 1987

    International Nuclear Information System (INIS)

    Griem, H.R.

    1987-12-01

    Thermal transport was investigated in laser-produced plasmas using spectroscopic measurements in the extreme ultraviolet. Theoretical work in collaboration with the University of Rochester allowed comparisons to be made of experimental spectra to a lagrangian hydrodynamic code. Results showed that transport is influenced by thermal flux inhibition in addition to non-uniformities in the laser irradiation. This work is a continuation of last year's project in which the main thermal transport results are reported. Very rich spectra were obtained in these experiments which yielded additional information on the ablating plasmas. A doppler shift was observed for neonlike titanium lines relative to higher ionization states of Ti. This shift is attributed to differences in expansion velocities between different charge states of Ti. A detailed report discussing this effect is attached. New lines were identified for Ti XXI and Ti XIX from these spectra in the wavelength region from 12 to 15 /angstrom/. The new heliumlike lines of Ti can exhibit population inversion and are candidates for x-ray laser experiments. A preprint of this paper is attached. Finally, line ratios of Ti XIX and Ti XX were employed to determine electron densities and temperatures. A report is also attached discussing these results

  16. Local-Scale Simulations of Nucleate Boiling on Micrometer Featured Surfaces: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Sitaraman, Hariswaran [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Moreno, Gilberto [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Narumanchi, Sreekant V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dede, Ercan M. [Toyota Research Institute of North America; Joshi, Shailesh N. [Toyota Research Institute of North America; Zhou, Feng [Toyota Research Institute of North America

    2017-08-03

    A high-fidelity computational fluid dynamics (CFD)-based model for bubble nucleation of the refrigerant HFE7100 on micrometer-featured surfaces is presented in this work. The single-fluid incompressible Navier-Stokes equations, along with energy transport and natural convection effects are solved on a featured surface resolved grid. An a priori cavity detection method is employed to convert raw profilometer data of a surface into well-defined cavities. The cavity information and surface morphology are represented in the CFD model by geometric mesh deformations. Surface morphology is observed to initiate buoyancy-driven convection in the liquid phase, which in turn results in faster nucleation of cavities. Simulations pertaining to a generic rough surface show a trend where smaller size cavities nucleate with higher wall superheat. This local-scale model will serve as a self-consistent connection to larger device scale continuum models where local feature representation is not possible.

  17. Empirical Profiling of Cold Hydrogen Plumes Formed from Venting Of LH2 Storage Vessels: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Buttner, William J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rivkin, Carl H [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schmidt, Kara [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hartmann, Kevin S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wright, Hannah [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Weidner, Eveline [Joint Research Centre, Petten, the Netherlands; Ciotti, Michael [H2 Fueling and CIP Markets Engineering

    2017-11-16

    Liquid hydrogen (LH2) storage is a viable approach to assuring sufficient hydrogen capacity at commercial fuelling stations. Presently, LH2 is produced at remote facilities and then transported to the end-use site by road vehicles (i.e., LH2 tanker trucks). Venting of hydrogen to depressurize the transport storage tank is a routine part of the LH2 delivery process. The behaviour of cold hydrogen plumes has not been well-characterized because empirical field data is essentially non-existent. The NFPA 2 Hydrogen Storage Safety Task Group, which consists of hydrogen producers, safety experts, and CFD modellers, has identified the lack of understanding of hydrogen dispersion during LH2 venting of storage vessel as a critical gap for establishing safety distances at LH2 facilities, especially commercial hydrogen fuelling stations. To address this need, the NREL sensor laboratory, in collaboration with the NFPA 2 Safety Task Group developed the Cold Hydrogen Plume Analyzer to empirically characterize the hydrogen plume formed during LH2 storage tank venting. A prototype Analyzer was developed and field-deployed at an actual LH2 venting operation with critical findings that included: - H2 being detected as much as 2 m lower than the release point, which is not predicted by existing models - A small and inconsistent correlation between oxygen depletion and the hydrogen concentration - A negligible to non-existent correlation between in-situ temperature and the hydrogen concentration The Analyzer is currently being upgraded for enhanced metrological capabilities including improved real-time spatial and temporal profiling of the plume and tracking of prevailing weather conditions. Additional deployments are planned to monitor plume behaviour under different wind, humidity, and temperatures. This data will be shared with the NFPA 2 Safety Task Group and ultimately will be used support theoretical models and code requirements prescribed in NFPA 2.

  18. Neutron transport

    International Nuclear Information System (INIS)

    Berthoud, Georges; Ducros, Gerard; Feron, Damien; Guerin, Yannick; Latge, Christian; Limoge, Yves; Santarini, Gerard; Seiler, Jean-Marie; Vernaz, Etienne; Coste-Delclaux, Mireille; M'Backe Diop, Cheikh; Nicolas, Anne; Andrieux, Catherine; Archier, Pascal; Baudron, Anne-Marie; Bernard, David; Biaise, Patrick; Blanc-Tranchant, Patrick; Bonin, Bernard; Bouland, Olivier; Bourganel, Stephane; Calvin, Christophe; Chiron, Maurice; Damian, Frederic; Dumonteil, Eric; Fausser, Clement; Fougeras, Philippe; Gabriel, Franck; Gagnier, Emmanuel; Gallo, Daniele; Hudelot, Jean-Pascal; Hugot, Francois-Xavier; Dat Huynh, Tan; Jouanne, Cedric; Lautard, Jean-Jacques; Laye, Frederic; Lee, Yi-Kang; Lenain, Richard; Leray, Sylvie; Litaize, Olivier; Magnaud, Christine; Malvagi, Fausto; Mijuin, Dominique; Mounier, Claude; Naury, Sylvie; Nicolas, Anne; Noguere, Gilles; Palau, Jean-Marc; Le Pallec, Jean-Charles; Peneliau, Yannick; Petit, Odile; Poinot-Salanon, Christine; Raepsaet, Xavier; Reuss, Paul; Richebois, Edwige; Roque, Benedicte; Royer, Eric; Saint-Jean, Cyrille de; Santamarina, Alain; Serot, Olivier; Soldevila, Michel; Tommasi, Jean; Trama, Jean-Christophe; Tsilanizara, Aime; Behar, Christophe; Provitina, Olivier; Lecomte, Michael; Forestier, Alain; Bender, Alexandra; Parisot, Jean-Francois; Finot, Pierre

    2013-10-01

    This bibliographical note presents a reference book which addresses the study of neutron transport in matter, the study of conditions for a chain reaction and the study of modifications of matter composition due to nuclear reactions. This book presents the main nuclear data, their measurement, assessment and processing, and the spallation. It proposes an overview of methods applied for the study of neutron transport: basic equations and their derived forms, deterministic methods and Monte Carlo method of resolution of the Boltzmann equation, methods of resolution of generalized Bateman equations, methods of time resolution of space kinetics coupled equations. It presents the main calculation codes, discusses the qualification and experimental aspects, and gives an overview of neutron transport applications: neutron transport calculation of reactors, neutron transport coupled with other disciplines, physics of fuel cycle, criticality

  19. Test Methodologies for Hydrogen Sensor Performance Assessment: Chamber vs. Flow Through Test Apparatus: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Buttner, William J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hartmann, Kevin S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schmidt, Kara [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cebolla, Rafeal O [Joint Research Centre, Petten, the Netherlands; Weidner, Eveline [Joint Research Centre, Petten, the Netherlands; Bonato, Christian [Joint Research Centre, Petten, the Netherlands

    2017-11-06

    Certification of hydrogen sensors to standards often prescribes using large-volume test chambers [1, 2]. However, feedback from stakeholders such as sensor manufacturers and end-users indicate that chamber test methods are often viewed as too slow and expensive for routine assessment. Flow through test methods potentially are an efficient, cost-effective alternative for sensor performance assessment. A large number of sensors can be simultaneously tested, in series or in parallel, with an appropriate flow through test fixture. The recent development of sensors with response times of less than 1s mandates improvements in equipment and methodology to properly capture the performance of this new generation of fast sensors; flow methods are a viable approach for accurate response and recovery time determinations, but there are potential drawbacks. According to ISO 26142 [1], flow through test methods may not properly simulate ambient applications. In chamber test methods, gas transport to the sensor can be dominated by diffusion which is viewed by some users as mimicking deployment in rooms and other confined spaces. Alternatively, in flow through methods, forced flow transports the gas to the sensing element. The advective flow dynamics may induce changes in the sensor behaviour relative to the quasi-quiescent condition that may prevail in chamber test methods. One goal of the current activity in the JRC and NREL sensor laboratories [3, 4] is to develop a validated flow through apparatus and methods for hydrogen sensor performance testing. In addition to minimizing the impact on sensor behaviour induced by differences in flow dynamics, challenges associated with flow through methods include the ability to control environmental parameters (humidity, pressure and temperature) during the test and changes in the test gas composition induced by chemical reactions with upstream sensors. Guidelines on flow through test apparatus design and protocols for the evaluation of

  20. Energy Storage Opportunities and Capabilities in a Type 3 Wind Turbine Generator: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Muljadi, Eduard; Gevorgian, Vahan; Hoke, Andy

    2016-09-01

    Wind power plants and other renewable power plants with power electronic interfaces are capable of delivering frequency response (both governor and/or inertial response) to the grid by a control action; thus, the reduction of available online inertia as conventional power plants are retired can be compensated by designing renewable power plant controls to include frequency response. The source of energy to be delivered as inertial response is determined by the type of generation and control strategy chosen. The cost of energy storage is expected to drop over time, and global research activities on energy storage are very active, funded both by the private industry and governments. Different industry sectors (e.g., transportation, energy) are the major drivers of the recent storage research and development. This work investigates the opportunities and capabilities of deploying energy storage in renewable power plants. In particular, we focus on wind power plants with doubly-fed induction generators, or Type 3 wind turbine generator (WTGs). We find that the total output power of a system with Type 3 WTGs with energy storage can deliver a power boost during inertial response that is up to 45% higher than one without energy storage without affecting the torque limit, thus enabling an effective delivery of ancillary services to the grid.

  1. Investing in Alternative Fuel Infrastructure: Insights for California from Stakeholder Interviews: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Melaina, Marc; Muratori, Matteo; McLaren, Joyce; Schwabe, Paul

    2017-03-13

    Increased interest in the use of alternative transportation fuels, such as natural gas, hydrogen, and electricity, is being driven by heightened concern about the climate impacts of gasoline and diesel emissions and our dependence on finite oil resources. A key barrier to widespread adoption of low- and zero-emission passenger vehicles is the availability of refueling infrastructure. Recalling the 'chicken and egg' conundrum, limited adoption of alternative fuel vehicles increases the perceived risk of investments in refueling infrastructure, while lack of refueling infrastructure inhibits vehicle adoption. In this paper, we present the results of a study of the perceived risks and barriers to investment in alternative fuels infrastructure, based on interviews with industry experts and stakeholders. We cover barriers to infrastructure development for three alternative fuels for passenger vehicles: compressed natural gas, hydrogen, and electricity. As an early-mover in zero emission passenger vehicles, California provides the early market experience necessary to map the alternative fuel infrastructure business space. Results and insights identified in this study can be used to inform investment decisions, formulate incentive programs, and guide deployment plans for alternative fueling infrastructure in the U.S. and elsewhere.

  2. Using Map Service API for Driving Cycle Detection for Wearable GPS Data: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-12-06

    Following advancements in smartphone and portable global positioning system (GPS) data collection, wearable GPS data have realized extensive use in transportation surveys and studies. The task of detecting driving cycles (driving or car-mode trajectory segments) from wearable GPS data has been the subject of much research. Specifically, distinguishing driving cycles from other motorized trips (such as taking a bus) is the main research problem in this paper. Many mode detection methods only focus on raw GPS speed data while some studies apply additional information, such as geographic information system (GIS) data, to obtain better detection performance. Procuring and maintaining dedicated road GIS data are costly and not trivial, whereas the technical maturity and broad use of map service application program interface (API) queries offers opportunities for mode detection tasks. The proposed driving cycle detection method takes advantage of map service APIs to obtain high-quality car-mode API route information and uses a trajectory segmentation algorithm to find the best-matched API route. The car-mode API route data combined with the actual route information, including the actual mode information, are used to train a logistic regression machine learning model, which estimates car modes and non-car modes with probability rates. The experimental results show promise for the proposed method's ability to detect vehicle mode accurately.

  3. Animal Transports

    Directory of Open Access Journals (Sweden)

    Diana Ludrovcová

    2016-08-01

    Full Text Available Purpose and Originality: The research is aimed to the animal transports issue, from two points of view – first is the animal cruelty and second is the policy and economic consideration. The goal is to acquaint the readers with the transports risks and its cruelty and evaluation of the economic, political aspects for he involved countries. The study is oriented on more points of view, what is rare in works with a similar theme. Method: This paper examines many issues and examinations from different authors and subsequently summarized the findings with authors own knowledge to one expanded unit. Results: Results proves, that livestock transports have negative impact on animal´s health, environment. Number of transported animals is rising every year. Society: Research familiarize the society with the animal transports, cruelty against animals during them, and influence of transports on some countries, their economy, policy. People get better informed and can form their own opinion on this topic. They may start acting, undertaking some steps to improve the present situation, what could help a lot to animals and environment. Limitations / further research: Future research could show progress and improvement of transports, quality of food supply and economics.

  4. Ocean transportation

    National Research Council Canada - National Science Library

    Frankel, Ernst G; Marcus, Henry S

    1973-01-01

    .... The discussion of technology considers the ocean transportation system as a whole, and the composite subsystems such as hull, outfit, propulsion, cargo handling, automation, and control and interface technology...

  5. Ocean transportation

    National Research Council Canada - National Science Library

    Frankel, Ernst G; Marcus, Henry S

    1973-01-01

    .... In ocean transportation economics we present investment and operating costs as well as the results of a study of financing of shipping. Similarly, a discussion of government aid to shipping is presented.

  6. Nicaragua - Transportation

    Data.gov (United States)

    Millennium Challenge Corporation — The evaluation examines impacts of the Transportation Project in three ways. First, we calculate economic rates of return associated with reduced user costs for each...

  7. Sediment Transport

    DEFF Research Database (Denmark)

    Liu, Zhou

    Flow and sediment transport are important in relation to several engineering topics, e.g. erosion around structures, backfilling of dredged channels and nearshore morphological change. The purpose of the present book is to describe both the basic hydrodynamics and the basic sediment transport...... mechanics. Chapter 1 deals with fundamentals in fluid mechanics with emphasis on bed shear stress by currents, while chapter 3 discusses wave boundary layer theory. They are both written with a view to sediment transport. Sediment transport in rivers, cross-shore and longshore are dealt with in chapters 2......, 4 and 5, respectively. It is not the intention of the book to give a broad review of the literature on this very wide topic. The book tries to pick up information which is of engineering importance. An obstacle to the study of sedimentation is the scale effect in model tests. Whenever small...

  8. RF transport

    International Nuclear Information System (INIS)

    Choroba, Stefan

    2013-01-01

    This paper deals with the techniques of transport of high-power radiofrequency (RF) power from a RF power source to the cavities of an accelerator. Since the theory of electromagnetic waves in waveguides and of waveguide components is very well explained in a number of excellent text books it will limit itself on special waveguide distributions and on a number of, although not complete list of, special problems which sometimes occur in RF power transportation systems. (author)

  9. Public transport

    OpenAIRE

    Lethbridge, Jane

    2008-01-01

    Public transport plays an essential role in enabling people from low income and other disadvantaged groups to access employment and services. It also contributes to the development of social networks and social capital, by helping people to visit friends and relatives and take part in community and other social activities. Public policy makers have begun to recognise that adequate public transport provision can play an important role in reducing social exclusion. [Taken from introductory para...

  10. Optimized Generator Designs for the DTU 10-MW Offshore Wind Turbine using GeneratorSE: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Sethuraman, Latha; Maness, Michael; Dykes, Katherine

    2017-01-01

    Compared to land-based applications, offshore wind imposes challenges for the development of next generation wind turbine generator technology. Direct-drive generators are believed to offer high availability, efficiency, and reduced operation and maintenance requirements; however, previous research suggests difficulties in scaling to several megawatts or more in size. The resulting designs are excessively large and/or massive, which are major impediments to transportation logistics, especially for offshore applications. At the same time, geared wind turbines continue to sustain offshore market growth through relatively cheaper and lightweight generators. However, reliability issues associated with mechanical components in a geared system create significant operation and maintenance costs, and these costs make up a large portion of overall system costs offshore. Thus, direct-drive turbines are likely to outnumber their gear-driven counterparts for this market, and there is a need to review the costs or opportunities of building machines with different types of generators and examining their competitiveness at the sizes necessary for the next generation of offshore wind turbines. In this paper, we use GeneratorSE, the National Renewable Energy Laboratory's newly developed systems engineering generator sizing tool to estimate mass, efficiency, and the costs of different generator technologies satisfying the electromagnetic, structural, and basic thermal design requirements for application in a very large-scale offshore wind turbine such as the Technical University of Denmark's (DTU) 10-MW reference wind turbine. For the DTU reference wind turbine, we use the previously mentioned criteria to optimize a direct-drive, radial flux, permanent-magnet synchronous generator; a direct-drive electrically excited synchronous generator; a medium-speed permanent-magnet generator; and a high-speed, doubly-fed induction generator. Preliminary analysis of leveled costs of

  11. Rail transportation by hydrogen vs. electrification - Case study for Ontario, Canada, II: Energy supply and distribution

    Energy Technology Data Exchange (ETDEWEB)

    Marin, G.D.; Naterer, G.F.; Gabriel, K. [University of Ontario Institute of Technology, Faculty of Engineering and Applied Sciences, 2000 Simcoe Street North, Oshawa, Ontario (Canada)

    2010-06-15

    Locomotives offer an efficient mode of transportation when compared to buses, personal vehicles or airplanes for mass transportation over frequent intercity distances. For example, a Bombardier Regina EMU train with 272 seats and a load factor of 53% will consume under 0.07 kWh/passenger-km, which is typically much lower than corresponding values for other transportation modes in similar circumstances. European countries have invested significantly over the years in train electrification. Environmentally friendly methods of transferring power to the wheels are direct electrification and hydrogen fuel cells. Various methods to produce hydrogen for utilization with fuel cell train operation are examined in this paper. This companion paper of a 2-paper set examines the overall impact of energy supply (hydrogen vs. electricity) and distribution on rail transportation, specifically in terms of costs and overall GHG emissions for a case study of GO transit along the Lakeshore corridor in Toronto. Although electrification of train services simplifies some aspects of the operation, when considered over the Lakeshore corridor alone, electrified trains lose their flexibility to serve cities outside the Lakeshore corridor. Hydrogen fuelled trains can provide a smoother transition and interoperability by operating the same routes and stations served by diesel trains today, without being limited to the Lakeshore corridor. This paper evaluates technological, operational and economic aspects of the electrification of the Lakeshore corridor, versus hydrogen train operation, including infrastructure requirements to provide service to a substantial ridership increase projected for the years 2015-2031. Various methods of hydrogen production and distribution are presented and analysed, in order to evaluate the overall life cycle of GHG emissions and costs for various train alternatives. (author)

  12. Preprint of the Fall 1997 JSAE (Japan Society of Automotive Engineers) Meeting Science Lecture. No. 975; Jidosha gijutsukai 1997 nen shuki taikai gakujutsu koenkai maezurishu. 975

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    No. 975 preprint of the Fall 1997 JSAE was summarized. As for the engine development, papers were made public on a study of reciprocating engine with Z mechanism, the combustion control system, etc. Attention was paid to internal combustion engine-electricity hybrid systems in terms of global warming prevention, and a study was made of environmental improvement effects by introducing next-generation automobiles. Image analysis and computer utilization in the structural design were also described. As to diesel engines, the combustion system and the exhaust gas problem were much studied. Also made were flow analysis on air conditioning and evaluation on the indoor thermal environment. Concerning the manufacturing process and materials, a lot of improvements were made public on thermal fatique resistance, reinforced materials, adoption of ceramics, corrosion resistance/wear resistance, etc. Operability and human engineering, and dynamics and safety are also important themes. Relating to the fuel, low fuel comsumption and additives were studied. The paper reported transmissions and the control systems, torque-transmitting mechanism, frictional property, etc. Especially, research/development were also much made of friction/wear resistant materials. ed and developed

  13. Orbital transport

    International Nuclear Information System (INIS)

    Oertel, H. Jr.; Koerner, H.

    1993-01-01

    The Third Aerospace Symposium in Braunschweig presented, for the first time, the possibility of bringing together the classical disciplines of aerospace engineering and the natural science disciplines of meteorology and air chemistry in a european setting. In this way, aspects of environmental impact on the atmosphere could be examined quantitatively. An essential finding of the european conference, is the unrestricted agreement of the experts that the given launch frequencies of the present orbital transport result in a negligible amount of pollutants being released in the atmosphere. The symposium does, however, call attention to the increasing need to consider the effect of orbital and atmospheric environmental impact of a future increase in launch frequencies of orbital transport in connection with future space stations. The Third Aerospace Symposium, 'Orbital Transport, Technical, Meteorological and Chemical Aspects', constituted a first forum of discussion for engineers and scientists. Questions of new orbital transport technologies and their environmental impact were to be discussed towards a first consensus. Through the 34 reports and articles, the general problems of space transportation and environmental protection were addressed, as well as particular aspects of high temperatures during reentry in the atmosphere of the earth, precision navigation of flight vehicles or flow behavior and air chemistry in the stratosphere. (orig./CT). 342 figs

  14. Travel and transport

    DEFF Research Database (Denmark)

    Bill, Jan; Roesdahl, Else

    2007-01-01

    On the interrelationship between travel, transport and society; on land transport, sea and river transport, and on winter transport;  on the related technologies and their developments......On the interrelationship between travel, transport and society; on land transport, sea and river transport, and on winter transport;  on the related technologies and their developments...

  15. Transport system

    NARCIS (Netherlands)

    Drenth, K.F.

    1999-01-01

    The transport system comprises at least one road surface (2) and at least one vehicle (4) on wheels (6). The road surface (2) has a substantially bowl-shaped cross section and the vehicle (4) is designed so that the wheels (6) run directly on the road surface (2) while the road surface (2) acts as a

  16. Optimal transport

    CERN Document Server

    Eckmann, B

    2008-01-01

    At the close of the 1980s, the independent contributions of Yann Brenier, Mike Cullen and John Mather launched a revolution in the venerable field of optimal transport founded by G Monge in the 18th century, which has made breathtaking forays into various other domains of mathematics ever since. The author presents a broad overview of this area.

  17. Nuclear transport

    International Nuclear Information System (INIS)

    Anon.

    2001-01-01

    Here is given the decree (2001/1199) of the 10. of december 2001 relative to the passing of safety rules concerning the maritime transport of spent fuels, plutonium and high-level radioactive wastes contained in packages. (O.M.)

  18. Transport fuel

    DEFF Research Database (Denmark)

    Ronsse, Frederik; Jørgensen, Henning; Schüßler, Ingmar

    2014-01-01

    Worldwide, the use of transport fuel derived from biomass increased four-fold between 2003 and 2012. Mainly based on food resources, these conventional biofuels did not achieve the expected emission savings and contributed to higher prices for food commod - ities, especially maize and oilseeds...

  19. Africa and electricity: To electrify Africa - necessary financial and human investments; The development of hydroelectricity in sub-Saharan Africa; A major challenge: to improve distribution efficiency; Smart grids in Africa?; Rural electrification in Africa; The development of renewable energies in Ethiopia - an example of empowerment of a local structure

    International Nuclear Information System (INIS)

    Horvilleur, Jacques; Favennec, Jean-Pierre; Cerdan, Jean-Pierre; Bauley, Jacky; Caumon, Pauline; Guerin, Andre-Jean; Beaussant, Henri; Louis, Frederic; Sall, Ousmane; Ledoux, Thierry; Boye, Henri; Bagayoko, Moussa

    2016-01-01

    This publication proposes a set of six articles which address various aspects related to the issue of Africa electrification. More precisely, the authors propose a general presentation of the present situation and an assessment of necessary financial, organisational, governance and training investments or needs (To electrify Africa: necessary financial and human investment), illustrate these issues in the case of hydroelectricity-rich Republic of Congo, discuss the issue of financing hydroelectricity development in Africa and of the need of operation and maintenance policies to meet needs associated with sustainable installations (The development of hydroelectricity in sub-Saharan Africa), address issues related to distribution through an improvement of existing distribution networks (A major challenge: to improve distribution efficiency) and through a possible development of smart grids (Smart grids in Africa?), comment issues related to rural electrification as a major challenge for these sometimes very poor areas with almost none financial resources, and evoke the possibilities associated with decentralised photovoltaic production (Rural electrification in Africa), and report interventions of an NGO in Ethiopia based on solar installations and actions of empowerment of local structures (The development of renewable energies in Ethiopia - an example of empowerment of a local structure)

  20. Nuclear transport

    International Nuclear Information System (INIS)

    Anon.

    2002-01-01

    During September and October 2001, 1 event has been reported and classified at the first level of the INES scale. This incident concerns the violation of the European regulation that imposes to any driver of radioactive matter of being the holder of a certificate asserting that he attended a special training. During this period, 13 in-site inspections have been made in places related to nuclear transport. (A.C.)

  1. Autonomous Energy Grids: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Kroposki, Benjamin D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Dall-Anese, Emiliano [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bernstein, Andrey [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhang, Yingchen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hodge, Brian S [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-10-04

    With much higher levels of distributed energy resources - variable generation, energy storage, and controllable loads just to mention a few - being deployed into power systems, the data deluge from pervasive metering of energy grids, and the shaping of multi-level ancillary-service markets, current frameworks to monitoring, controlling, and optimizing large-scale energy systems are becoming increasingly inadequate. This position paper outlines the concept of 'Autonomous Energy Grids' (AEGs) - systems that are supported by a scalable, reconfigurable, and self-organizing information and control infrastructure, can be extremely secure and resilient (self-healing), and self-optimize themselves in real-time for economic and reliable performance while systematically integrating energy in all forms. AEGs rely on scalable, self-configuring cellular building blocks that ensure that each 'cell' can self-optimize when isolated from a larger grid as well as partaking in the optimal operation of a larger grid when interconnected. To realize this vision, this paper describes the concepts and key research directions in the broad domains of optimization theory, control theory, big-data analytics, and complex system modeling that will be necessary to realize the AEG vision.

  2. Michigan transportation facts & figures : public transportation

    Science.gov (United States)

    2002-08-16

    This on-line document is part of a series, Transportation Facts & Figures, by the Michigan Department of Transportation (MDOT). The Public Transit section of Transportation Facts & Figures cover such topics as intercity bus service, intercity rail se...

  3. Analysis of transport administrators and sustainable transport ...

    African Journals Online (AJOL)

    Analysis of transport administrators and sustainable transport development in Lagos, Ogun and Oyo States, Nigeria. ... A good transportation system planning and management is considered vital for ... EMAIL FULL TEXT EMAIL FULL TEXT

  4. Transporter Classification Database (TCDB)

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Transporter Classification Database details a comprehensive classification system for membrane transport proteins known as the Transporter Classification (TC)...

  5. Energy transport

    International Nuclear Information System (INIS)

    Anon.

    1982-01-01

    The measurement of primary interaction cross sections and the incorporation of these data into Monte Carlo calculations provide detailed information about the initial spatial distribution of absorbed dose. Our theoretical energy transport studies have focused on the use of this information to predict the evolution of chemical species formed as a result of the energy deposition. This effort has led to a stochastic approach to diffusion kinetics that can account for the influence of track structure on the yield of free radicals in the radiolysis of water. Fluorescence studies with pulsed alpha particle and proton beams provided the first experimental test of our stochastic model of tract structure effects. Our experimental studies use time-resolved emission spectroscopy to investigate the mechanism of energy transport in nonpolar liquids. Studies of the concentration dependence of time-resolved emission from solutions of benzene in cyclohexane also show the importance of using low benzene concentrations to minimize the influence of benzene dimers on the emission kinetics

  6. National transportation statistics 2011

    Science.gov (United States)

    2011-04-01

    Compiled and published by the U.S. Department of Transportation's Bureau of Transportation Statistics : (BTS), National Transportation Statistics presents information on the U.S. transportation system, including : its physical components, safety reco...

  7. National Transportation Statistics 2008

    Science.gov (United States)

    2009-01-08

    Compiled and published by the U.S. Department of Transportations Bureau of Transportation Statistics (BTS), National Transportation Statistics presents information on the U.S. transportation system, including its physical components, safety record...

  8. State Transportation Statistics 2012

    Science.gov (United States)

    2013-08-15

    The Bureau of Transportation Statistics (BTS), a part of the U.S. Department of Transportation's (USDOT) Research and Innovative Technology Administration (RITA), presents State Transportation Statistics 2012, a statistical profile of transportation ...

  9. National Transportation Statistics 2009

    Science.gov (United States)

    2010-01-21

    Compiled and published by the U.S. Department of Transportation's Bureau of Transportation Statistics (BTS), National Transportation Statistics presents information on the U.S. transportation system, including its physical components, safety record, ...

  10. State Transportation Statistics 2014

    Science.gov (United States)

    2014-12-15

    The Bureau of Transportation Statistics (BTS) presents State Transportation Statistics 2014, a statistical profile of transportation in the 50 states and the District of Columbia. This is the 12th annual edition of State Transportation Statistics, a ...

  11. Transport of radioactive substances

    International Nuclear Information System (INIS)

    2014-12-01

    The report on the transport of radioactive substances covers the following topics: facts on radioactive materials transport, safety of the transport of radioactive substances, legal regulations and guidelines: a multiform but consistent system, transport of nuclear fuels, safety during the transport of nuclear fuel, future transport of spent fuel elements and high-level radioactive wastes in Germany.

  12. Exploitation des mesures électriques en vue de la surveillance et du diagnostic en temps réel des piles à combustible pour application transport automobile

    OpenAIRE

    Taleb , Miassa

    2015-01-01

    In the current global energy context, proton exchange membrane fuel cells represent a promising solution to the future development of a new generation of electrified vehicles, allowing greater autonomy than electrified vehicles using batteries.Nevertheless, the large-scale development of fuel cells remains limited due to some technological locks, such as water management. To enable mass production of fuel cells, such problems must be solved. Several working axes may be envisaged both on the h...

  13. Chemical transport reactions

    CERN Document Server

    Schäfer, Harald

    2013-01-01

    Chemical Transport Reactions focuses on the processes and reactions involved in the transport of solid or liquid substances to form vapor phase reaction products. The publication first offers information on experimental and theoretical principles and the transport of solid substances and its special applications. Discussions focus on calculation of the transport effect of heterogeneous equilibria for a gas motion between equilibrium spaces; transport effect and the thermodynamic quantities of the transport reaction; separation and purification of substances by means of material transport; and

  14. Beam transport

    International Nuclear Information System (INIS)

    1988-01-01

    Considerable experience has now been gained with the various beam transport lines, and a number of minor changes have been made to improve the ease of operation. These include: replacement of certain little-used slits by profile monitors (harps or scanners); relocation of steering magnets, closer to diagnostic harps or profile scanners; installation of a scanner inside the isocentric neutron therapy system; and conversion of a 2-doublet quadrupole telescope (on the neutron therapy beamline) to a 2-triplet telescope. The beam-swinger project has been delayed by very late delivery of the magnet iron to the manufacturer, but is now progressing smoothly. The K=600 spectrometer magnets have now been delivered and are being assembled for field mapping. The x,y-table with its associated mapping equipment is complete, together with the driver software. One of the experimental areas has been dedicated to the production of collimated neutron beams and has been equipped with a bending magnet and beam dump, together with steel collimators fixed at 4 degrees intervals from 0 degrees to 16 degrees. Changes to the target cooling and shielding system for isotope production have led to a request for much smaller beam spot sizes on target, and preparations have been made for rearrangement of the isotope beamline to permit installation of quadrupole triplets on the three beamlines after the switching magnet. A practical system of quadrupoles for matching beam properties to the spectrometer has been designed. 6 figs

  15. Plant Transporter Identification

    DEFF Research Database (Denmark)

    Larsen, Bo

    Membrane transport proteins (transporters) play a critical role for numerous biological processes, by controlling the movements of ions and molecules in and out of cells. In plants, transporters thus function as gatekeepers between the plant and its surrounding environment and between organs......, tissues, cells and intracellular compartments. Since plants are highly compartmentalized organisms with complex transportation infrastructures, they consequently have many transporters. However, the vast majority of predicted transporters have not yet been experimentally verified to have transport...... activity. This project contains a review of the implemented methods, which have led to plant transporter identification, and present our progress on creating a high-throughput functional genomics transporter identification platform....

  16. Transport of Radioactive Materials

    International Nuclear Information System (INIS)

    2001-01-01

    This address overviews the following aspects: concepts on transport of radioactive materials, quantities used to limit the transport, packages, types of packages, labeling, index transport calculation, tags, labeling, vehicle's requirements and documents required to authorize transportation. These requirements are considered in the regulation of transport of radioactive material that is in drafting step

  17. Transportation and the environment.

    NARCIS (Netherlands)

    Banister, D.; Anderton, K.; Bonilla, D.; Givoni, M.; Schwanen, T.

    2011-01-01

    The growth of CO2-intensive transport, mobility and the impact of transport on the environment are reviewed. The recent global exponential growth in transport is unsustainable and must end unless the transport sector can decarbonize. The paper examines solutions for low-carbon transport systems; the

  18. Transportation librarian's toolkit

    Science.gov (United States)

    2007-12-01

    The Transportation Librarians Toolkit is a product of the Transportation Library Connectivity pooled fund study, TPF- 5(105), a collaborative, grass-roots effort by transportation libraries to enhance information accessibility and professional expert...

  19. Advanced Transportation Institute 2008.

    Science.gov (United States)

    2009-02-01

    The seventh version of the Advanced Transportation Institute (ATI-08) was conducted in 2008 to encourage high school students to pursue careers in the field of transportation engineering. The University Transportation Center for Alabama partnered wit...

  20. Advanced Transportation Institute 2009.

    Science.gov (United States)

    2009-09-01

    The eighth version of the Advanced Transportation Institute (ATI-09) was conducted in 2009 to encourage high school students to pursue careers in the field of transportation engineering. The University Transportation Center for Alabama partnered with...

  1. Innovative Technologies in Transportation

    Science.gov (United States)

    2004-12-01

    An historical overview of the transportation infrastructure of the United States and Texas is provided. Data for trends in transportation is analyzed and projections for the future are postulated. A survey of current technologies in transportation is...

  2. State Transportation Statistics 2010

    Science.gov (United States)

    2011-09-14

    The Bureau of Transportation Statistics (BTS), a part of DOTs Research and Innovative Technology Administration (RITA), presents State Transportation Statistics 2010, a statistical profile of transportation in the 50 states and the District of Col...

  3. State transportation statistics 2009

    Science.gov (United States)

    2009-01-01

    The Bureau of Transportation Statistics (BTS), a part of DOTs Research and : Innovative Technology Administration (RITA), presents State Transportation : Statistics 2009, a statistical profile of transportation in the 50 states and the : District ...

  4. State Transportation Statistics 2011

    Science.gov (United States)

    2012-08-08

    The Bureau of Transportation Statistics (BTS), a part of DOTs Research and Innovative Technology Administration (RITA), presents State Transportation Statistics 2011, a statistical profile of transportation in the 50 states and the District of Col...

  5. State Transportation Statistics 2013

    Science.gov (United States)

    2014-09-19

    The Bureau of Transportation Statistics (BTS), a part of the U.S. Department of Transportations (USDOT) Research and Innovative Technology Administration (RITA), presents State Transportation Statistics 2013, a statistical profile of transportatio...

  6. Smart Growth and Transportation

    Science.gov (United States)

    Describes the relationship between smart growth and transportation, focusing smart and sustainable street design, transit-oriented development, parking management, sustainable transportation planning, and related resources.

  7. Neoclassical transport in NCSX

    International Nuclear Information System (INIS)

    Mikkelsen, D.R.; Zarnstorff, M.C.; Beidler, C.D.; Maassberg, H.; Houlberg, W.A.; Spong, D.A.; Tribaldos, V.

    2003-01-01

    Methods for calculating neoclassical transport in the National Compact Stellarator Experiment (NCSX) are discussed, with particular attention to developing computationally inexpensive predictions of neoclassical transport. (orig.)

  8. Journal of transportation engineering

    National Research Council Canada - National Science Library

    1983-01-01

    The Journal of Transportation Engineering contains technical and professional articles on the planning, design, construction, maintenance, and operation of air, highway, rail, and urban transportation...

  9. Transportation Industry 2004

    National Research Council Canada - National Science Library

    Miller, Evan; Kathir, Nathan; Brogan, Dennis M

    2004-01-01

    .... Because the defense sector relies on commercial transportation for both peacetime activities and for power projection, senior military leaders must understand the global transportation industry...

  10. Saxton Transportation Operations Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Saxton Transportation Operations Laboratory (Saxton Laboratory) is a state-of-the-art facility for conducting transportation operations research. The laboratory...

  11. Development of a Trip Energy Estimation Model Using Real-World Global Positioning System Driving Data: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Tian, Ye [Metropia, Inc.

    2017-09-15

    A data-driven technique for estimation of energy requirements for a proposed vehicle trip has been developed. Based on over 700,000 miles of driving data, the technique has been applied to generate a model that estimates trip energy requirements. The model uses a novel binning approach to categorize driving by road type, traffic conditions, and driving profile. The trip-level energy estimations can easily be aggregated to any higher-level transportation system network desired. The model has been tested and validated on the Austin, Texas, data set used to build this model. Ground-truth energy consumption for the data set was obtained from Future Automotive Systems Technology Simulator (FASTSim) vehicle simulation results. The energy estimation model has demonstrated 12.1 percent normalized total absolute error. The energy estimation from the model can be used to inform control strategies in routing tools, such as change in departure time, alternate routing, and alternate destinations, to reduce energy consumption. The model can also be used to determine more accurate energy consumption of regional or national transportation networks if trip origin and destinations are known. Additionally, this method allows the estimation tool to be tuned to a specific driver or vehicle type.

  12. Green Routing Fuel Saving Opportunity Assessment: A Case Study on California Large-Scale Real-World Travel Data: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Lei; Holden, Jacob; Gonder, Jeff; Wood, Eric

    2017-07-13

    New technologies, such as connected and automated vehicles, have attracted more and more researchers for improving the energy efficiency and environmental impact of current transportation systems. The green routing strategy instructs a vehicle to select the most fuel-efficient route before the vehicle departs. It benefits the current transportation system with fuel saving opportunity through identifying the greenest route. This paper introduces an evaluation framework for estimating benefits of green routing based on large-scale, real-world travel data. The framework has the capability to quantify fuel savings by estimating the fuel consumption of actual routes and comparing to routes procured by navigation systems. A route-based fuel consumption estimation model, considering road traffic conditions, functional class, and road grade is proposed and used in the framework. An experiment using a large-scale data set from the California Household Travel Survey global positioning system trajectory data base indicates that 31% of actual routes have fuel savings potential with a cumulative estimated fuel savings of 12%.

  13. Modelling freight transport

    NARCIS (Netherlands)

    Tavasszy, L.A.; Jong, G. de

    2014-01-01

    Freight Transport Modelling is a unique new reference book that provides insight into the state-of-the-art of freight modelling. Focusing on models used to support public transport policy analysis, Freight Transport Modelling systematically introduces the latest freight transport modelling

  14. Transport of radioactive materials

    International Nuclear Information System (INIS)

    2013-01-01

    This ninth chapter presents de CNEN-NE--5.01 norm 'Transport of radioactive material'; the specifications of the radioactive materials for transport; the tests of the packages; the requests for controlling the transport and the responsibilities during the transport of radioactive material

  15. Water-transporting proteins

    DEFF Research Database (Denmark)

    Zeuthen, Thomas

    2010-01-01

    . In the K(+)/Cl(-) and the Na(+)/K(+)/2Cl(-) cotransporters, water is entirely cotransported, while water transport in glucose uniporters and Na(+)-coupled transporters of nutrients and neurotransmitters takes place by both osmosis and cotransport. The molecular mechanism behind cotransport of water...... transport. Epithelial water transport is energized by the movements of ions, but how the coupling takes place is uncertain. All epithelia can transport water uphill against an osmotic gradient, which is hard to explain by simple osmosis. Furthermore, genetic removal of aquaporins has not given support...... to osmosis as the exclusive mode of transport. Water cotransport can explain the coupling between ion and water transport, a major fraction of transepithelial water transport and uphill water transport. Aquaporins enhance water transport by utilizing osmotic gradients and cause the osmolarity...

  16. Blood Sample Transportation by Pneumatic Transportation Systems

    DEFF Research Database (Denmark)

    Nybo, Mads; Lund, Merete E; Titlestad, Kjell

    2018-01-01

    BACKGROUND: Pneumatic transportation systems (PTSs) are increasingly used for transportation of blood samples to the core laboratory. Many studies have investigated the impact of these systems on different types of analyses, but to elucidate whether PTSs in general are safe for transportation...... analysis, and the hemolysis index). CONCLUSIONS: Owing to their high degree of heterogeneity, the retrieved studies were unable to supply evidence for the safety of using PTSs for blood sample transportation. In consequence, laboratories need to measure and document the actual acceleration forces...

  17. Magnetic type transportation system

    International Nuclear Information System (INIS)

    Kobama, Masao.

    1981-01-01

    Purpose: To enable automatic transportation of nuclear substances with optional setting for the transportation distance, even for a long distance, facilitating the automation of the transportation and decreasing the space for the installation of a direction converging section of the transporting path. Constitution: A transporting vehicle having a pair of permanent magnets or ferromagnetic bodies mounted with a predetermined gap to each other along the transporting direction is provided in the transporting path including a bent direction change section for transporting specimens such as nuclear materials, and a plurality of driving vehicles having permanent magnets or ferromagnetic bodies for magnetically attracting the transporting vehicle from outside of the transporting path are arranged to the outside of the transporting path. At least one of the driving vehicles is made to run along the transporting direction of the transporting path by a driving mechanism incorporating running section such as an endless chain to drive the transportation vehicle, and the transporting vehicle is successively driven by each of the driving mechanisms. (Kawakami, Y.)

  18. Trip Energy Estimation Methodology and Model Based on Real-World Driving Data for Green Routing Applications: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Van Til, Harrison J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-02-09

    A data-informed model to predict energy use for a proposed vehicle trip has been developed in this paper. The methodology leverages nearly 1 million miles of real-world driving data to generate the estimation model. Driving is categorized at the sub-trip level by average speed, road gradient, and road network geometry, then aggregated by category. An average energy consumption rate is determined for each category, creating an energy rates look-up table. Proposed vehicle trips are then categorized in the same manner, and estimated energy rates are appended from the look-up table. The methodology is robust and applicable to almost any type of driving data. The model has been trained on vehicle global positioning system data from the Transportation Secure Data Center at the National Renewable Energy Laboratory and validated against on-road fuel consumption data from testing in Phoenix, Arizona. The estimation model has demonstrated an error range of 8.6% to 13.8%. The model results can be used to inform control strategies in routing tools, such as change in departure time, alternate routing, and alternate destinations to reduce energy consumption. This work provides a highly extensible framework that allows the model to be tuned to a specific driver or vehicle type.

  19. Comparing Statewide Economic Impacts of New Generation from Wind, Coal, and Natural Gas in Arizona, Colorado, and Michigan: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Tegen, S.

    2005-08-01

    With increasing concerns about energy independence, job outsourcing, and risks of global climate change, it is important for policy makers to understand all impacts from their decisions about energy resources. This paper assesses one aspect of the impacts: direct economic effects. The paper compares impacts to states from equivalent new electrical generation from wind, natural gas, and coal. Economic impacts include materials and labor for construction, operations, maintenance, fuel extraction, and fuel transport, as well as project financing, property tax, and landowner revenues. We examine spending on plant construction during construction years, in addition to all other operational expenditures over a 20-year span. Initial results indicate that adding new wind power can be more economically effective than adding new gas or coal power, and that a higher percentage of dollars spent on coal and gas will leave the state. For this report, we interviewed industry representatives and energy experts, in addition to consulting government documents, models, and existing literature. The methodology for this research can be adapted to other contexts for determining economic effects of new power generation in other states and regions.

  20. Transportation Technology: Rail Transport and Logistics

    Science.gov (United States)

    Lang, Aaron B.

    2011-01-01

    Transportation can simply be defined as the movement of goods, services, and people from one location to another. Without an efficient means to transport goods from place to place, the economy would be nothing like it is today. Throughout the history of the United States, American railroads have paved the way toward creating a nation of great…

  1. Information disclosure on transport

    International Nuclear Information System (INIS)

    Kubo, M.

    1998-01-01

    In Japan, the transport of nuclear fuel materials strictly meets the above international convention and domestic regulations as well. Information on the transport of nuclear fuel materials within the country and between the country and foreign countries is treated carefully. Nuclear fuel materials are categorized for transport and are physically protected accordingly. Certain transportation information is treated with special precautions, including prior arrangements among sender, recipient and carrier, and prior agreement between entities subject to the jurisdiction and regulation of supplier and recipient countries. In the case of international transport, this information includes specifying time, place and procedures for transferring transport and responsibility. (O.M.)

  2. Secure Transportation Management

    International Nuclear Information System (INIS)

    Gibbs, P. W.

    2014-01-01

    Secure Transport Management Course (STMC) course provides managers with information related to procedures and equipment used to successfully transport special nuclear material. This workshop outlines these procedures and reinforces the information presented with the aid of numerous practical examples. The course focuses on understanding the regulatory framework for secure transportation of special nuclear materials, identifying the insider and outsider threat(s) to secure transportation, organization of a secure transportation unit, management and supervision of secure transportation units, equipment and facilities required, training and qualification needed.

  3. Monte Carlo Transport for Electron Thermal Transport

    Science.gov (United States)

    Chenhall, Jeffrey; Cao, Duc; Moses, Gregory

    2015-11-01

    The iSNB (implicit Schurtz Nicolai Busquet multigroup electron thermal transport method of Cao et al. is adapted into a Monte Carlo transport method in order to better model the effects of non-local behavior. The end goal is a hybrid transport-diffusion method that combines Monte Carlo Transport with a discrete diffusion Monte Carlo (DDMC). The hybrid method will combine the efficiency of a diffusion method in short mean free path regions with the accuracy of a transport method in long mean free path regions. The Monte Carlo nature of the approach allows the algorithm to be massively parallelized. Work to date on the method will be presented. This work was supported by Sandia National Laboratory - Albuquerque and the University of Rochester Laboratory for Laser Energetics.

  4. Sustainable Transportation and Health

    Directory of Open Access Journals (Sweden)

    Norbert Mundorf

    2018-03-01

    Full Text Available We are experiencing a shift in thinking about Transportation and Mobility, which makes this Special Issue on Sustainable Transportation and Health in the International Journal of Environmental Research and Public Health especially timely.[...

  5. Arizona transportation history.

    Science.gov (United States)

    2011-12-01

    The Arizona transportation history project was conceived in anticipation of Arizonas centennial, which will be : celebrated in 2012. Following approval of the Arizona Centennial Plan in 2007, the Arizona Department of : Transportation (ADOT) recog...

  6. Department of Transportation

    Science.gov (United States)

    ... of Drone Integration Pilot Program MEET THE SECRETARY TRANSPORTATION TUESDAY FEATURED NEWS The Briefing Room Connect With ... Carriers - Get a DOT Number Find Your State Transportation Department 5 Star Automobile Crash Test Ratings Office ...

  7. Transportation Management Workshop: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    This report is a compilation of discussions presented at the Transportation Management Workshop held in Gaithersburg, Maryland. Topics include waste packaging, personnel training, robotics, transportation routing, certification, containers, and waste classification.

  8. TRANSPORTATION ECONOMIC TRENDS 2017

    Science.gov (United States)

    2018-01-05

    The report has eight chapters: - Chapter 1 introduces the Transportation Services Index, a monthly summary of freight and passenger movement. - Chapter 2 explains what transportation contributes to the American economy. - Chapter 3 examines the costs...

  9. Oxygen transport membrane

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a novel composite oxygen transport membrane as well as its preparation and uses thereof.......The present invention relates to a novel composite oxygen transport membrane as well as its preparation and uses thereof....

  10. Transport not as others

    International Nuclear Information System (INIS)

    Gruhier, Fabien.

    1979-01-01

    Transport of radioactive materials will increase with the development of nuclear power station. Problems arising are examined. Some examples of past accidents are given. Thermal and impact tests of containers and categories of transport are recalled [fr

  11. Transportation Management Workshop: Proceedings

    International Nuclear Information System (INIS)

    1993-01-01

    This report is a compilation of discussions presented at the Transportation Management Workshop held in Gaithersburg, Maryland. Topics include waste packaging, personnel training, robotics, transportation routing, certification, containers, and waste classification

  12. National transportation statistics 2010

    Science.gov (United States)

    2010-01-01

    National Transportation Statistics presents statistics on the U.S. transportation system, including its physical components, safety record, economic performance, the human and natural environment, and national security. This is a large online documen...

  13. Transportation Services Index

    Data.gov (United States)

    Department of Transportation — The TSI is a monthly measure of the volume of services performed by the for-hire transportation sector. The index covers the activities of for-hire freight carriers,...

  14. Fault classification method for the driving safety of electrified vehicles

    Science.gov (United States)

    Wanner, Daniel; Drugge, Lars; Stensson Trigell, Annika

    2014-05-01

    A fault classification method is proposed which has been applied to an electric vehicle. Potential faults in the different subsystems that can affect the vehicle directional stability were collected in a failure mode and effect analysis. Similar driveline faults were grouped together if they resembled each other with respect to their influence on the vehicle dynamic behaviour. The faults were physically modelled in a simulation environment before they were induced in a detailed vehicle model under normal driving conditions. A special focus was placed on faults in the driveline of electric vehicles employing in-wheel motors of the permanent magnet type. Several failures caused by mechanical and other faults were analysed as well. The fault classification method consists of a controllability ranking developed according to the functional safety standard ISO 26262. The controllability of a fault was determined with three parameters covering the influence of the longitudinal, lateral and yaw motion of the vehicle. The simulation results were analysed and the faults were classified according to their controllability using the proposed method. It was shown that the controllability decreased specifically with increasing lateral acceleration and increasing speed. The results for the electric driveline faults show that this trend cannot be generalised for all the faults, as the controllability deteriorated for some faults during manoeuvres with low lateral acceleration and low speed. The proposed method is generic and can be applied to various other types of road vehicles and faults.

  15. Adhesion signals of phospholipid vesicles at an electrified interface.

    Science.gov (United States)

    DeNardis, Nadica Ivošević; Žutić, Vera; Svetličić, Vesna; Frkanec, Ruža

    2012-09-01

    General adhesion behavior of phospholipid vesicles was examined in a wide range of potentials at the mercury electrode by recording time-resolved adhesion signals. It was demonstrated that adhesion-based detection is sensitive to polar headgroups in phospholipid vesicles. We identified a narrow potential window around the point of zero charge of the electrode where the interaction of polar headgroups of phosphatidylcholine vesicles with the substrate is manifested in the form of bidirectional signals. The bidirectional signal is composed of the charge flow due to the nonspecific interaction of vesicle adhesion and spreading and of the charge flow due to a specific interaction of the negatively charged electrode and the most exposed positively charged choline headgroups. These signals are expected to appear only when the electrode surface charge density is less than the surface charge density of the choline groups at the contact interface. In comparison, for the negatively charged phosphatidylserine vesicles, we identified the potential window at the mercury electrode where charge compensation takes place, and bidirectional signals were not detected.

  16. Localization properties of one-dimensional electrified chains

    International Nuclear Information System (INIS)

    Ouasti, R.; Brezini, A.; Zekri, N.

    1993-08-01

    A Kronig-Penney model with a constant electric filed for a non-interacting electron is used to study the transmission properties of Anderson transition in one-dimensional (1-D) systems with disordered strengths of δ-function potentials. we examined the cases where the potential varies uniformly from O to W (barriers) or from -W to O (wells) for a given disorder W. Mainly, we observe unexpected abrupt transition at the points E + Fx = n 2 π 2 . However, these transitions are related to the small oscillations observed by Soukoulis et al. in the mixed case (wells and barriers). An interesting feature in the wells is that in the presence of a small field the states become more localized and the localization length decrease up to a minimum for a critical value F m . In the end, we have studied the effect of the disorder on the Anderson transition by the mean of the participation ratio and the localization length. (author). 27 refs, 6 figs

  17. Ab Initio Thermodynamic Modeling of Electrified Metal-Oxide Interfaces

    DEFF Research Database (Denmark)

    Zeng, Zhenhua; Hansen, Martin Hangaard; Greeley, Jeff

    2015-01-01

    Solid oxide fuel cells are attractive devices in a sustainable energy context because of their fuel flexibility and potentially highly efficient conversion of chemical to electrical energy. The performance of the device is to a large extent determined by the atomic structure of the electrode-elec...

  18. Renewable energy projects to electrify rural communities in Cape Verde

    International Nuclear Information System (INIS)

    Ranaboldo, Matteo; Lega, Bruno Domenech; Ferrenbach, David Vilar; Ferrer-Martí, Laia; Moreno, Rafael Pastor; García-Villoria, Alberto

    2014-01-01

    Highlights: • The design of 2 off-grid electrification projects in Cape Verde is developed. • Configurations with hybrid renewable energy systems and micro-grids are considered. • A detailed micro-scale wind resource assessment is carried out. • An optimization model is used in order to support the design. • The proposed system is economically beneficial in comparison with diesel generation. - Abstract: Even though Cape Verde has high wind and solar energy resources, the conventional strategy for increasing access to electricity in isolated rural areas is by centralized microgrids with diesel generators. In this study, the design of 2 off-grid electrification projects based on hybrid wind–photovoltaic systems in Cape Verde is developed and analyzed. The design considers some significant novelty features in comparison with previous studies. First a detailed wind resource assessment is carried out combining meso-scale wind climate data and a specialized micro-scale wind flow model. Then a mathematical model is used for the design of off-grid projects considering a combination of individual systems and microgrids. In this study, locations far from the demand points are also considered as possible generation points. Various design configurations are analyzed and compared. The proposed configurations exploit the highest wind potential areas and are economically beneficial in comparison with diesel generator systems

  19. Collisional avalanche exponentiation of runaway electrons in electrified plasmas

    International Nuclear Information System (INIS)

    Jayakumar, R.; Fleischmann, H.H.; Zweben, S.J.

    1993-01-01

    In contrast to earlier expectations, it is estimated that generation of runaway electrons from close collisions of existing runaways with cold plasma electrons can be significant even for small electric fields, whenever runaways can gain energies of about 20 MeV or more. In that case, the runaway population will grow exponentially with the energy spectrum showing an exponential decrease towards higher energies. Energy gains of the required magnitude may occur in large tokamak devices as well as in cosmic-ray generation. (orig.)

  20. A Game Changer: Electrifying Remote Communities by Using Isolated Microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Xiaonan; Wang, Jianhui

    2017-06-01

    Microgrids, as self-contained entities, are of increasing interest in modern electric grids. Microgrids provide a sustainable solution to aggregate distributed energy resources (DERs) [e.g., photovoltaics (PVs), wind turbines], energy storage, and loads in a localized manner, especially in distribution systems. As a controllable unit, a microgrid can manage and balance the source and load power inside it to ensure stable and reliable operation. Moreover, through coordination with upper-level control systems, it can be dispatched and respond to the control commands issued by the central controller in the distribution system-in other words, a system that is effectively a distribution management system (DMS).

  1. PV power and profit? Electrifying rural South Africa

    International Nuclear Information System (INIS)

    Karottki, R.; Banks, D.

    2000-01-01

    This article traces the background to the implementation of a programme of sustainable off-grid energy services delivered to rural areas through private-public partnership. The implementation of the school photovoltaic (PV) electrification programme, electrification of rural clinics, the solar electrification of rural households on a large scale through a joint venture between Shell Renewables and the national utility ESKOM, and the electrification of widely scattered homesteads are discussed. Details are given of the financial support from the government and the National Electricity Regulator, the development of a national standard for Solar Home Systems, identification of target regions, the regulatory framework, and the opportunities for business and for real improvement. (UK)

  2. Harmonic analysis of electrified railway based on improved HHT

    Science.gov (United States)

    Wang, Feng

    2018-04-01

    In this paper, the causes and harms of the current electric locomotive electrical system harmonics are firstly studied and analyzed. Based on the characteristics of the harmonics in the electrical system, the Hilbert-Huang transform method is introduced. Based on the in-depth analysis of the empirical mode decomposition method and the Hilbert transform method, the reasons and solutions to the endpoint effect and modal aliasing problem in the HHT method are explored. For the endpoint effect of HHT, this paper uses point-symmetric extension method to extend the collected data; In allusion to the modal aliasing problem, this paper uses the high frequency harmonic assistant method to preprocess the signal and gives the empirical formula of high frequency auxiliary harmonic. Finally, combining the suppression of HHT endpoint effect and modal aliasing problem, an improved HHT method is proposed and simulated by matlab. The simulation results show that the improved HHT is effective for the electric locomotive power supply system.

  3. Molecular ordering at electrified interfaces: Template and potential effects

    Directory of Open Access Journals (Sweden)

    Thanh Hai Phan

    2014-09-01

    Full Text Available A combination of cyclic voltammetry and in situ scanning tunneling microscopy was employed to examine the adsorption and phase transition of 1,1’-dibenzyl-4,4’-bipyridinium molecules (abbreviated as DBV2+ on a chloride-modified Cu(111 electrode surface. The cyclic voltammogram (CV of the Cu(111 electrode exposed to a mixture of 10 mM HCl and 0.1 mM DBVCl2 shows three distinguishable pairs of current waves P1/P’1, P2/P’2, and P3/P’3 which are assigned to two reversible electron transfer steps, representing the reduction of the dicationic DBV2+ to the corresponding radical monocationic DBV+• (P1/P’1 and then to the uncharged DBV0 (P3/P’3 species, respectively, as well as the chloride desorption/readsorption processes (P2/P’2. At positive potentials (i.e., above P1 the DBV2+ molecules spontaneously adsorb and form a highly ordered phase on the c(p × √3-precovered Cl/Cu(111 electrode surface. A key element of this DBV2+ adlayer is an assembly of two individual DBV2+ species which, lined up, forms a so-called “herring-bone” structure. Upon lowering the electrode potential the first electron transfer step (at P1 causes a phase transition from the DBV2+-related herring-bone phase to the so-called "alternating stripe" pattern built up by the DBV+• species following a nucleation and growth mechanism. Comparison of both observed structures with those found earlier at different electrode potentials on a c(2 × 2Cl-precovered Cu(100 electrode surface enables a clear assessment of the relative importance of adsorbate–substrate and adsorbate–adsorbate interactions, i.e., template vs self-assembly effects, in the structure formation process of DBV cations on these modified Cu electrode surfaces.

  4. Evidence for an electrifying violation of cosmic censorship

    International Nuclear Information System (INIS)

    Horowitz, Gary T; Santos, Jorge E; Way, Benson

    2016-01-01

    We present a plausible counterexample to cosmic censorship in four-dimensional Einstein–Maxwell theory with asymptotically anti-de Sitter boundary conditions. Smooth initial data evolves to a region of arbitrarily large curvature that is visible to distant observers. Our example is based on a holographic model of an electrically charged, localised defect which was previously studied at zero temperature. We partially extend those results to nonzero temperatures. (paper)

  5. To electrify bilingualism: Electrophysiological insights into bilingual metaphor comprehension.

    Science.gov (United States)

    Jankowiak, Katarzyna; Rataj, Karolina; Naskręcki, Ryszard

    2017-01-01

    Though metaphoric language comprehension has previously been investigated with event-related potentials, little attention has been devoted to extending this research from the monolingual to the bilingual context. In the current study, late proficient unbalanced Polish (L1)-English (L2) bilinguals performed a semantic decision task to novel metaphoric, conventional metaphoric, literal, and anomalous word pairs presented in L1 and L2. The results showed more pronounced P200 amplitudes to L2 than L1, which can be accounted for by differences in the subjective frequency of the native and non-native lexical items. Within the early N400 time window (300-400 ms), L2 word dyads evoked delayed and attenuated amplitudes relative to L1 word pairs, possibly indicating extended lexical search during foreign language processing, and weaker semantic interconnectivity for L2 compared to L1 words within the memory system. The effect of utterance type was observed within the late N400 time window (400-500 ms), with smallest amplitudes evoked by literal, followed by conventional metaphoric, novel metaphoric, and anomalous word dyads. Such findings are interpreted as reflecting more resource intensive cognitive mechanisms governing novel compared to conventional metaphor comprehension in both the native and non-native language. Within the late positivity time window (500-800 ms), Polish novel metaphors evoked reduced amplitudes relative to literal utterances. In English, on the other hand, this effect was observed for both novel and conventional metaphoric word dyads. This finding might indicate continued effort in information retrieval or access to the non-literal route during novel metaphor comprehension in L1, and during novel and conventional metaphor comprehension in L2. Altogether, the present results point to decreased automaticity of cognitive mechanisms engaged in non-native and non-dominant language processing, and suggest a decreased sensitivity to the levels of conventionality of metaphoric meanings in late proficient unbalanced bilingual speakers.

  6. Transport of MOX fuel

    International Nuclear Information System (INIS)

    Porter, I.R.; Carr, M.

    1997-01-01

    The regulatory framework which governs the transport of MOX fuel is set out, including packages, transport modes and security requirements. Technical requirements for the packages are reviewed and BNFL's experience in plutonium and MOX fuel transport is described. The safety of such operations and the public perception of safety are described and the question of gaining public acceptance for MOX fuel transport is addressed. The paper concludes by emphasising the need for proactive programmes to improve the public acceptance of these operations. (Author)

  7. Radioactive materials transport

    International Nuclear Information System (INIS)

    Talbi, B.

    1996-01-01

    The development of peaceful applications of nuclear energy results in the increase of transport operations of radioactive materials. Therefore strong regulations on transport of radioactive materials turns out to be a necessity in Tunisia. This report presents the different axes of regulations which include the means of transport involved, the radiation protection of the carriers, the technical criteria of security in transport, the emergency measures in case of accidents and penalties in case of infringement. (TEC). 12 refs., 1 fig

  8. TRANSPORTATION INFORMATION CLEARINGHOUSE

    OpenAIRE

    Allen, Karin; Dijohn, Joseph; Misek, Shamus

    2005-01-01

    The Transportation Information Clearinghouse (TIC) Project was the result of collaboration among the Regional Transportation Authority, the Workforce Boards of Metropolitan Chicago and the Urban Transportation Center (UTC) at the University of Illinois at Chicago (UIC). The primary objective of the project was to identify privatelyprovided, employer-based, non-traditional transportation services in operation as well as specific information about these services in order for employers, Workforc...

  9. Preprint of the results of `the publicly applied proposal type and hi-tech (emphasized) field research and development in fiscal 1995`; `1995 nendo teian kobogata saisentan (juten) bun`ya kenkyu kaihatsu` seika hokokukai yokoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-01

    The preprint was prepared of a report meeting for the results of `the publicly applied proposal type and hi-tech (emphasized) field research and development in fiscal 1995` to be held in Tokyo during February 12 to 14, 1997. In the meeting, a lecture titled `The system of fundamental researches and its execution` is to be given as a special lecture and the following are as general lectures: `Energy/environmental technology and next generation catalysts,` ` The present and outlook of surgery in the 21st century - computer surgery,` The present situation of education and research related to the design of digital integrated systems,` and `The present and future of research and development of a new carbon material, fullerene.` Research reports were prepared by field as follows: 73 papers in the new material technology field, 46 in the bio-technology field, 36 in the electronics/information technology field, 8 in the mechanical system technology field, 8 in the human life engineering technology field, 23 in the medical/welfare equipment technology field, 5 in the resource technology field, 17 in the energy/environment technology field.

  10. Transport statistics 1995

    CSIR Research Space (South Africa)

    De Haan, ML

    1996-04-01

    Full Text Available This publication contains information on all major modes of transport in South Africa. The transport sector is placed in perspective relative to the macro economy and a number of important transport indicators are given. The document also contains...

  11. Transports of radioactive materials

    International Nuclear Information System (INIS)

    Sousselier, Yves

    1982-01-01

    Transport safety depends on the packaging, and the degree of safety must be adapted to the potential hazards of the substance carried. The various kinds of packagings and their strength are examined and the transport of irradiated fuels from the safety angle is taken as example and a comparison is made with the transport of conventional dangerous substances [fr

  12. Transport of radioactive materials

    International Nuclear Information System (INIS)

    Lenail, B.

    1984-01-01

    Transport of radioactive materials is dependent of transport regulations. In practice integrated doses for personnel during transport are very low but are more important during loading or unloading a facility (reactor, plant, laboratory, ...). Risks occur also if packagings are used outside specifications. Recommendations to avoid these risks are given [fr

  13. Transportation in African Development.

    Science.gov (United States)

    Altschul, Robert D.

    1980-01-01

    Examines the structure, role, and needs of Africa's national and intracontinental transportation system. Characteristics of rail, water, road, and air transportation are examined. The conclusion is that high investment in transportation systems is essential to the development process. (Author/KC)

  14. Competing Transport Networks

    NARCIS (Netherlands)

    M.J. van der Leij (Marco)

    2003-01-01

    textabstractIn a circular city model, I consider network design and pricing decisions for a single fast transport connection that faces competition from a slower but better accessible transport mode. To access the fast transport network individuals have to make complementary trips by slow mode. This

  15. NATURAL GAS TRANSPORTATION

    OpenAIRE

    Stanis³aw Brzeziñski

    2007-01-01

    In the paper, Author presents chosen aspects of natural gas transportation within global market. Natural gas transportation is a technicaly complicated and economicly expensive process; in infrastructure construction and activities costs. The paper also considers last and proposed initiatives in natural gas transportation.

  16. Assessing Sensitiveness to Transport

    DEFF Research Database (Denmark)

    Lieb, Christoph; Suter, Stefan; Sánchez, Alfredo

    Summary The EU-project ASSET (ASessing SEnsitiveness to Transport) aims at developing and implementing a concise concept to assess transport sensitive areas (TSA) in a European context, i.e. areas in which transport leads to more serious impacts than in other areas. The aim of work package 2 (WP2...

  17. Road Transport Entrepreneurs and Road Transportation Revolution ...

    African Journals Online (AJOL)

    Toshiba

    upon a massive road-building programme throughout the colony. The rapid expansion ..... transportation problems of his textile customers and palm produce producers and ... unflinching loyalty and solidarity with their illustrious son, General.

  18. Transportation and public health.

    Science.gov (United States)

    Litman, Todd

    2013-01-01

    This article investigates various ways that transportation policy and planning decisions affect public health and better ways to incorporate public health objectives into transport planning. Conventional planning tends to consider some public health impacts, such as crash risk and pollution emissions measured per vehicle-kilometer, but generally ignores health problems resulting from less active transport (reduced walking and cycling activity) and the additional crashes and pollution caused by increased vehicle mileage. As a result, transport agencies tend to undervalue strategies that increase transport system diversity and reduce vehicle travel. This article identifies various win-win strategies that can help improve public health and other planning objectives.

  19. Convective transport in tokamaks

    International Nuclear Information System (INIS)

    D'Ippolito, D.A.; Myra, J.R.; Russell, D.A.; Krasheninnikov, S.I.; Pigarov, A.Yu.; Yu, G.Q.; Xu, X.Q.; Nevins, W.M.

    2005-01-01

    Scrape-off-layer (SOL) convection in fusion experiments appears to be a universal phenomenon that can 'short-circuit' the divertor in some cases. The theory of 'blob' transport provides a simple and robust physical paradigm for studying convective transport. This paper summarizes recent advances in the theory of blob transport and its comparison with 2D and 3D computer simulations. We also discuss the common physical basis relating radial transport of blobs, pellets, and ELMs and a new blob regime that may lead to a connection between blob transport and the density limit. (author)

  20. Theory of contributon transport

    International Nuclear Information System (INIS)

    Painter, J.W.; Gerstl, S.A.W.; Pomraning, G.C.

    1980-10-01

    A general discussion of the physics of contributon transport is presented. To facilitate this discussion, a Boltzmann-like transport equation for contributons is obtained, and special contributon cross sections are defined. However, the main goal of this study is to identify contributon transport equations and investigate possible deterministic solution techniques. Four approaches to the deterministic solution of the contributon transport problem are investigated. These approaches are an attempt to exploit certain attractive properties of the contributon flux, psi = phi phi + , where phi and phi + are the solutions to the forward and adjoint Boltzmann transport equations

  1. Transportation Business Plan

    International Nuclear Information System (INIS)

    1986-01-01

    The Transportation Business Plan is a step in the process of procuring the transportation system. It sets the context for business strategy decisions by providing pertinent background information, describing the legislation and policies governing transportation under the NWPA, and describing requirements of the transportation system. Included in the document are strategies for procuring shipping casks and transportation support services. In the spirit of the NWPA directive to utilize the private sector to the maximum extent possible, opportunities for business ventures are obvious throughout the system development cycle

  2. A review on idling reduction strategies to improve fuel economy and reduce exhaust emissions of transport vehicles

    International Nuclear Information System (INIS)

    Shancita, I.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Rashed, M.M.; Rashedul, H.K.

    2014-01-01

    Highlights: • Introduce various idling reduction technologies for transport vehicles. • Exhibit their energy use, advantages, disadvantages to understand their capability. • Conduct critical review to improve fuel economy and exhaust emissions. • Suggest better technology according to their performance ability. - Abstract: To achieve reductions in vehicle idling, strategies and actions must be taken to minimize the time spent by drivers idling their engines. A number of benefits can be obtained in limiting the idling time. These benefits include savings in fuel use and maintenance costs, vehicle life extension, and reduction in exhaust emissions. The main objective of idling reduction (IR) devices is to reduce the amount of energy wasted by idling trucks, rail locomotives, and automobiles. During idling, gasoline vehicles emit a minimum amount of nitrogen oxides (NO x ) and negligible particulate matter (PM). However, generally a large amount of carbon monoxide (CO) and hydrocarbons (HC) are produced from these vehicles. Gasoline vehicles consume far more fuel at an hourly rate than their diesel counterparts during idling. Higher NOx and comparatively larger PM are produced by diesel vehicles than gasoline vehicles on the average during idling. Auxiliary power unit (APU), direct-fired heaters, fuel cells, thermal storage system, truck stop electrification, battery-based systems, engine idle management (shutdown) systems, electrical (shore power) solutions, cab comfort system, and hybridization are some of the available IR technologies whose performances for reducing fuel consumption and exhaust emissions have been compared. This paper analyzes the availability and capability of most efficient technologies to reduce fuel consumption and exhaust emissions from diesel and gasoline vehicles by comparing the findings of previous studies. The analysis reveals that among all the options direct fired heaters, APUs and electrified parking spaces exhibit better

  3. Advancing Transportation through Vehicle Electrification - PHEV

    Energy Technology Data Exchange (ETDEWEB)

    Bazzi, Abdullah [Chrysler Group LLC, Auburn Hills, MI (United States); Barnhart, Steven [Chrysler Group LLC, Auburn Hills, MI (United States)

    2014-12-31

    FCA US LLC viewed the American Recovery and Reinvestment Act (ARRA) as an historic opportunity to learn about and develop PHEV technologies and create the FCA US LLC engineering center for Electrified Powertrains. The ARRA funding supported FCA US LLC’s light-duty electric drive vehicle and charging infrastructure-testing activities and enabled FCA US LLC to utilize the funding on advancing Plug-in Hybrid Electric Vehicle (PHEV) technologies for production on future programs. FCA US LLC intended to develop the next-generations of electric drive and energy batteries through a properly paced convergence of standards, technology, components and common modules. To support the development of a strong, commercially viable supplier base, FCA US LLC also utilized this opportunity to evaluate various designated component and sub-system suppliers. The original proposal of this project was submitted in May 2009 and selected in August 2009. The project ended in December 2014.

  4. Transportation safety training

    International Nuclear Information System (INIS)

    Jones, E.

    1990-01-01

    Over the past 25 years extensive federal legislation involving the handling and transport of hazardous materials/waste has been passed that has resulted in numerous overlapping regulations administered and enforced by different federal agencies. The handling and transport of hazardous materials/waste involves a significant number of workers who are subject to a varying degree of risk should an accident occur during handling or transport. Effective transportation training can help workers address these risks and mitigate them, and at the same time enable ORNL to comply with the federal regulations concerning the transport of hazardous materials/waste. This presentation will outline how the Environmental and Health Protection Division's Technical Resources and Training Section at the Oak Ridge National Laboratory, working with transportation and waste disposal personnel, have developed and implemented a comprehensive transportation safety training program to meet the needs of our workers while satisfying appropriate federal regulations. 8 refs., 3 tabs

  5. Transportation System Requirements Document

    International Nuclear Information System (INIS)

    1993-09-01

    This Transportation System Requirements Document (Trans-SRD) describes the functions to be performed by and the technical requirements for the Transportation System to transport spent nuclear fuel (SNF) and high-level radioactive waste (HLW) from Purchaser and Producer sites to a Civilian Radioactive Waste Management System (CRWMS) site, and between CRWMS sites. The purpose of this document is to define the system-level requirements for Transportation consistent with the CRWMS Requirement Document (CRD). These requirements include design and operations requirements to the extent they impact on the development of the physical segments of Transportation. The document also presents an overall description of Transportation, its functions, its segments, and the requirements allocated to the segments and the system-level interfaces with Transportation. The interface identification and description are published in the CRWMS Interface Specification

  6. TRANSPORT/HANDLING REQUESTS

    CERN Multimedia

    Groupe ST/HM

    2002-01-01

    A new EDH document entitled 'Transport/Handling Request' will be in operation as of Monday, 11th February 2002, when the corresponding icon will be accessible from the EDH desktop, together with the application instructions. This EDH form will replace the paper-format transport/handling request form for all activities involving the transport of equipment and materials. However, the paper form will still be used for all vehicle-hire requests. The introduction of the EDH transport/handling request form is accompanied by the establishment of the following time limits for the various services concerned: 24 hours for the removal of office items, 48 hours for the transport of heavy items (of up to 6 metric tons and of standard road width), 5 working days for a crane operation, extra-heavy transport operation or complete removal, 5 working days for all transport operations relating to LHC installation. ST/HM Group, Logistics Section Tel: 72672 - 72202

  7. Transport of radioactive substances; Der Transport radioaktiver Stoffe

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2014-12-15

    The report on the transport of radioactive substances covers the following topics: facts on radioactive materials transport, safety of the transport of radioactive substances, legal regulations and guidelines: a multiform but consistent system, transport of nuclear fuels, safety during the transport of nuclear fuel, future transport of spent fuel elements and high-level radioactive wastes in Germany.

  8. Stochastic models of intracellular transport

    KAUST Repository

    Bressloff, Paul C.; Newby, Jay M.

    2013-01-01

    mechanisms for intracellular transport: passive diffusion and motor-driven active transport. Diffusive transport can be formulated in terms of the motion of an overdamped Brownian particle. On the other hand, active transport requires chemical energy, usually

  9. Modelling of transport phenomena

    International Nuclear Information System (INIS)

    Itoh, Kimitaka; Itoh, Sanae; Fukuyama, Atsushi.

    1993-09-01

    In this review article, we discuss key features of the transport phenomena and theoretical modelling to understand them. Experimental observations have revealed the nature of anomalous transport, i.e., the enhancement of the transport coefficients by the gradients of the plasma profiles, the pinch phenomena, the radial profile of the anomalous transport coefficients, the variation of the transport among the Bohm diffusion, Pseudo-classical confinement, L-mode and variety of improved confinement modes, and the sudden jumps such as L-H transition. Starting from the formalism of the transport matrix, the modelling based on the low frequency instabilities are reviewed. Theoretical results in the range of drift wave frequency are examined. Problems in theories based on the quasilinear and mixing-length estimates lead to the renewal of the turbulence theory, and the physics picture of the self-sustained turbulence is discussed. The theory of transport using the fluid equation of plasma is developed, showing that the new approach is very promising in explaining abovementioned characteristics of anomalous transport in both L-mode and improved confinement plasmas. The interference of the fluxes is the key to construct the physics basis of the bifurcation theory for the L-H transition. The present status of theories on the mechanisms of improved confinement is discussed. Modelling on the nonlocal nature of transport is briefly discussed. Finally, the impact of the anomalous transport on disruptive phenomena is also described. (author) 95 refs

  10. Transport, energy and environment

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-01

    Transportation demands a large and increasing share of total energy consumption in Europe. At the same time many European countries are facing difficult decisions in achieving their long term environmental goals. Therefore energy policy, environmental policy and transport policy should be seen and discussed in a common perspective. In particular the relative contribution from the transport sector and the energy sector involves a number of important and difficult issues. The aim of the conference was to bring together economists, scientists, manufactures, energy planners, transport planners, and decision makers in order to discuss the importance of the transport sector in relation to energy demand and long term environmental goals. General conference sessions covered. Trends in Transport Energy Demand and Environmental constraints, Technological Development and New Transport Systems, Lifestyle Changes and the Transport Sector, Megacities: Solutions to the Transport and Air Pollution Problems, Effectiveness of Public Policies, Transport and Energy sector, and Methods, Models and Data. The conference took place at Hotel Marienlyst, Elsinore, Denmark and attracted wide interest. The participants represented 14 different countries covering international organisations, ministries, universities, research centres, consulting firms, industry etc. (EG)

  11. Energy policy in transport and transport policy

    International Nuclear Information System (INIS)

    Van Dender, Kurt

    2009-01-01

    Explanations for, and indirect evidence of, imperfections in the market for private passenger vehicle fuel economy suggest there is a reasonable case for combining fuel economy standards and fuel or carbon taxes to contribute to an energy policy that aims to reduce greenhouse gas emissions and improve energy security. Estimates of key elasticities, including the rebound effect, indicate that the positive and negative side-effects of fuel economy measures on transport activities and external costs are limited. However, an energy policy for transport does not replace a transport policy that aims to manage the main transport externalities including congestion and local pollution. Conventional marginal cost estimates and standard cost-benefit reasoning suggest that policies that address congestion and local pollution likely bring benefits at least as large as those from fuel economy measures. But the large uncertainty on the possible effects of greenhouse gas emissions constitutes a strong challenge for standard cost-benefit reasoning. Emerging results from methods to cope with this uncertainty suggest that policies to stimulate the widespread adoption of low-carbon technologies in transport are justified.

  12. Energy policy in transport and transport policy

    Energy Technology Data Exchange (ETDEWEB)

    Van Dender, Kurt [Joint Transport Research Centre of the International Transport Forum and the OECD, 2 rue Andre Pascale, F-75775 Paris Cedex 16 (France)

    2009-10-15

    Explanations for, and indirect evidence of, imperfections in the market for private passenger vehicle fuel economy suggest there is a reasonable case for combining fuel economy standards and fuel or carbon taxes to contribute to an energy policy that aims to reduce greenhouse gas emissions and improve energy security. Estimates of key elasticities, including the rebound effect, indicate that the positive and negative side-effects of fuel economy measures on transport activities and external costs are limited. However, an energy policy for transport does not replace a transport policy that aims to manage the main transport externalities including congestion and local pollution. Conventional marginal cost estimates and standard cost-benefit reasoning suggest that policies that address congestion and local pollution likely bring benefits at least as large as those from fuel economy measures. But the large uncertainty on the possible effects of greenhouse gas emissions constitutes a strong challenge for standard cost-benefit reasoning. Emerging results from methods to cope with this uncertainty suggest that policies to stimulate the widespread adoption of low-carbon technologies in transport are justified. (author)

  13. EBS Radionuclide Transport Abstraction

    International Nuclear Information System (INIS)

    J. Prouty

    2006-01-01

    The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment (TSPA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers advective transport and diffusive transport

  14. EBS Radionuclide Transport Abstraction

    Energy Technology Data Exchange (ETDEWEB)

    J. Prouty

    2006-07-14

    The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment (TSPA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers advective transport and diffusive transport

  15. Transportation: Grade 8. Cluster IV.

    Science.gov (United States)

    Calhoun, Olivia H.

    A curriculum guide for grade 8, the document is devoted to the occupational cluster "Transportation." It is divided into five units: surface transportation, interstate transportation, air transportation, water transportation, and subterranean transportation (the Metro). Each unit is introduced by a statement of the topic, the unit's…

  16. Transport Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    Transport is the sector with the highest final energy consumption and, without any significant policy changes, is forecast to remain so. In 2008, the IEA published 25 energy efficiency recommendations, among which four are for the transport sector. The recommendations focus on road transport and include policies on improving tyre energy efficiency, fuel economy standards for both light-duty vehicles and heavy-duty vehicles, and eco-driving. Implementation of the recommendations has been weaker in the transport sector than others. This paper updates the progress that has been made in implementing the transport energy efficiency recommendations in IEA countries since March 2009. Many countries have in the last year moved from 'planning to implement' to 'implementation underway', but none have fully implemented all transport energy efficiency recommendations. The IEA calls therefore for full and immediate implementation of the recommendations.

  17. Transportation Emissions: some basics

    DEFF Research Database (Denmark)

    Kontovas, Christos A.; Psaraftis, Harilaos N.

    2016-01-01

    transportation and especially carbon dioxide emissions are at the center stage of discussion by the world community through various international treaties, such as the Kyoto Protocol. The transportation sector also emits non-CO2 pollutants that have important effects on air quality, climate, and public health......Transportation is the backbone of international trade and a key engine driving globalization. However, there is growing concern that the Earth’s atmospheric composition is being altered by human activities, including transportation, which can lead to climate change. Air pollution from....... The main purpose of this chapter is to introduce some basic concepts that are relevant in the quest of green transportation logistics. First, we present the basics of estimating emissions from transportation activities, the current statistics and future trends, as well as the total impact of air emissions...

  18. Astrocytic GABA Transporters

    DEFF Research Database (Denmark)

    Schousboe, Arne; Wellendorph, Petrine; Frølund, Bente

    2017-01-01

    , and several of these compounds have been shown to exhibit pronounced anticonvulsant activity in a variety of animal seizure models. As proof of concept of the validity of this drug development approach, one GABA-transport inhibitor, tiagabine, has been developed as a clinically active antiepileptic drug......Inactivation of GABA-mediated neurotransmission is achieved by high-affinity transporters located at both GABAergic neurons and the surrounding astrocytes. Early studies of the pharmacological properties of neuronal and glial GABA transporters suggested that different types of transporters might...... be expressed in the two cell types, and such a scenario was confirmed by the cloning of four distinctly different GABA transporters from a number of different species. These GABA-transport entities have been extensively characterized using a large number of GABA analogues of restricted conformation...

  19. Transport of radioactive wastes

    International Nuclear Information System (INIS)

    Stuller, C.

    2003-01-01

    In this article author describes the system of transport and processing of radioactive wastes from nuclear power of Slovenske elektrarne, plc. It is realized the assurance of transport of liquid and solid radioactive wastes to processing links from places of their formation, or of preliminary storage and consistent transports of treated radioactive wastes fixed in cement matrix of fibre-concrete container into Rebublic storage of radioactive wastes in Mochovce

  20. Transport of radioactive materials

    International Nuclear Information System (INIS)

    1991-07-01

    The purpose of this Norm is to establish, relating to the TRANSPORT OF RADIOACTIVE MATERIALS, safety and radiological protection requirements to ensure an adequate control level of the eventual exposure of persons, properties and environment to the ionizing radiation comprising: specifications on radioactive materials for transport; package type selection; specification of the package design and acceptance test requirements; arrangements relating to the transport itself; administrative requirements and responsibilities. (author)

  1. Radioactive material air transportation

    International Nuclear Information System (INIS)

    Pader y Terry, Claudio Cosme

    2002-01-01

    As function of the high aggregated value, safety regulations and the useful life time, the air transportation has been used more regularly because is fast, reliable, and by giving great security to the cargo. Based on the International Atomic Energy Agency (IAEA), the IATA (International Air Transportation Association) has reproduced in his dangerous goods manual (Dangerous Goods Regulations - DGR IATA), the regulation for the radioactive material air transportation. Those documents support this presentation

  2. Handling and Transport Problems

    Energy Technology Data Exchange (ETDEWEB)

    Pomarola, J. [Head of Technical Section, Atomic Energy Commission, Saclay (France); Savouyaud, J. [Head of Electro-Mechanical Sub-Division, Atomic Energy Commission, Saclay (France)

    1960-07-01

    Arrangements for special or dangerous transport operations by road arising out of the activities of the Atomic Energy Commission are made by the Works and Installations Division which acts in concert with the Monitoring and Protection Division (MPD) whenever radioactive substances or appliances are involved. In view of the risk of irradiation and contamination entailed in handling and transporting radioactive substances, including waste, a specialized transport and storage team has been formed as a complement to the emergency and decontamination teams.

  3. Transport Nuclear Liability Insurance

    International Nuclear Information System (INIS)

    Folens, M.

    2006-01-01

    Although transport of nuclear substances represents only a very small part of the global transport of dangerous goods, it takes place every day all over the world and it is part of our daily life. Transport of nuclear material takes also place at every stage of the nuclear fuel cycle; radioactive materials are carried out all over the world by all major modes of transport: sea, air, road and rail. Despite the large number of nuclear transports, they are not considered as posing a serious risk. A major nuclear incident is almost always associated with the operating of fixed installations such as nuclear power plants; just think about Three Mile Island and Chernobyl. This perception is strengthened by the absence so far of serious accidents in the nuclear transport sector and this finding is in fact proof of the very safe conditions of nuclear transport. But accidents can never be excluded entirely and in some cases damages could be as large as those caused by fixed installations. This means that protection of the interests of possible victims should also be covered in a correct way. That is why the special nuclear liability regime has also been developed to cover damage caused by a nuclear transport accident. As stated by Patrick Reyners, the prime motivation for originally adopting a special nuclear regime was the harmonisation of national legislation and that nowhere more than in the field of international transport operations is such harmonisation felt desirable . The international legal regime has been developed along two tracks, one based on the mode of transport and the other based on the notion of dangerous goods. The linkage between those two tracks is of permanent concern and the mode of transport is the key element to determine which international instrument should be applicable. The purpose of this paper is to briefly introduce the financial security provided by the insurance industry to cover the international nuclear liability regime for nuclear

  4. Freight transport and intermodality

    OpenAIRE

    Barbero Mañanes, Eduardo

    2010-01-01

    During recent decades, there has been very substantial growth in the freight transport sector. Freight transport is increasing faster than the economy or passenger transport. Demand is increasing more rapidly than supply and is resulting in environmental and social problems. Increasing congestion, too, is affecting efficient and reliable freight distribution, and consequently having a deleterious effect on local economies. Intermodality is therefore needed to make better use of alternative mo...

  5. Climate Change and Transportation

    OpenAIRE

    Yevdokimov, Yuri

    2010-01-01

    As stated at the beginning of this chapter, the relationship between transportation and climate is two-directional. Based on our statistical analysis performed for Canada, we can make some general conclusions about this relationship. On the one hand, transportation is one of the largest contributors to GHG emissions which, in turn, cause various changes in climate. On the other hand, these climate changes negatively affect transportation in terms of its infrastructure and operations. Therefor...

  6. Transport barriers in plasmas

    International Nuclear Information System (INIS)

    Caldas, I L; Szezech, J D Jr; Kroetz, T; Marcus, F A; Roberto, M; Viana, R L; Lopes, S R

    2012-01-01

    We discuss the creation of transport barriers in magnetically confined plasmas with non monotonic equilibrium radial profiles. These barriers reduce the transport in the shearless region (i.e., where the twist condition does not hold). For the chaotic motion of particles in an equilibrium electric field with a nonmonotonic radial profile, perturbed by electrostatic waves, we show that a nontwist transport barrier can be created in the plasma by modifying the electric field radial profile. We also show non twist barriers in chaotic magnetic field line transport in the plasma near to the tokamak wall with resonant modes due to electric currents in external coils.

  7. Urban transportation projects conceptualised:

    DEFF Research Database (Denmark)

    Pineda, Andres Felipe Valderrama

    is straightforward: transportation projects transform cities. The paradoxical reality thus is that a problem that has been traditionally conceptualized in technical terms (transportation engineering, transportation economics, planning theory, traffic engineering, urban planning, etc.), has tremendous consequences...... operation when discussing transportation projects in big cities. The tradition of Science and Technology Studies might have provided some clues. In the following paper we discuss the most prominent aspects of some theories in STS in order to understand and conceptualize the cases of Bogotá and Copenhagen...

  8. WASTE PACKAGE TRANSPORTER DESIGN

    International Nuclear Information System (INIS)

    Weddle, D.C.; Novotny, R.; Cron, J.

    1998-01-01

    The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''

  9. WASTE PACKAGE TRANSPORTER DESIGN

    Energy Technology Data Exchange (ETDEWEB)

    D.C. Weddle; R. Novotny; J. Cron

    1998-09-23

    The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''.

  10. EUROPEAN MARITIME TRANSPORT POLICY

    Directory of Open Access Journals (Sweden)

    Jerzy Kujawa

    2014-03-01

    Full Text Available The article describes the common EU policy on maritime transport, which comprises almost 80% of the volume of external trade of the Union and about 40% of internal transport needs. The first part of the paper presents the origins of the common maritime transport policy and the difficulties encountered during its initial formation. Subsequently, the evolution of the concepts of the policy and its current shape is discussed. The final, substantial part of the article describes the main aims and directions of the EU maritime transport policy and includes an evaluation of the effects of the policy.

  11. Intelligent Freigth Transport Systems

    DEFF Research Database (Denmark)

    Overø, Helene Martine; Larsen, Allan; Røpke, Stefan

    2009-01-01

    is to enhance the efficiency and lower the environmental impact in freight transport. In this paper, a pilot project involving real-time waste collection at a Danish waste collection company is described, and a solution approach is proposed. The problem corresponds to the dynamic version of the waste collection......The Danish innovation project entitled “Intelligent Freight Transport Systems” aims at developing prototype systems integrating public intelligent transport systems (ITS) with the technology in vehicles and equipment as well as the IT-systems at various transport companies. The objective...

  12. Moisture Transport in Wood

    DEFF Research Database (Denmark)

    Astrup, Thomas; Hansen, Kurt Kielsgaard; Hoffmeyer, Preben

    2005-01-01

    Modelling of moisture transport in wood is of great importance as most mechanical and physical properties of wood depend on moisture content. Moisture transport in porous materials is often described by Ficks second law, but several observations indicate that this does not apply very well to wood....... Recently at the Technical University of Denmark, Department of Civil Engineering, a new model for moisture transport in wood has been developed. The model divides the transport into two phases, namely water vapour in the cell lumens and bound water in the cell walls....

  13. UZ Colloid Transport Model

    International Nuclear Information System (INIS)

    McGraw, M.

    2000-01-01

    The UZ Colloid Transport model development plan states that the objective of this Analysis/Model Report (AMR) is to document the development of a model for simulating unsaturated colloid transport. This objective includes the following: (1) use of a process level model to evaluate the potential mechanisms for colloid transport at Yucca Mountain; (2) Provide ranges of parameters for significant colloid transport processes to Performance Assessment (PA) for the unsaturated zone (UZ); (3) Provide a basis for development of an abstracted model for use in PA calculations

  14. Heavy transport problems

    International Nuclear Information System (INIS)

    Haas, K.F.

    1975-01-01

    Assuming that very often a long transport route from the factory of the manufacturer to the provided site has to be reckoned with, in general only transport with a ship is possible. As each site is only called by a certain steamship line, at a very early stage of planning the nuclear power plant the possibilities and capacities of the lines and means of transportation under discussion should be investigated. In planning the unloading equipment at the site, due consideration should be given to the fact that at a later time this equipment should also be suitable for the transport of heavy components and spent fuel assemblies. (orig.) [de

  15. Heme transport and erythropoiesis

    Science.gov (United States)

    Yuan, Xiaojing; Fleming, Mark D.; Hamza, Iqbal

    2013-01-01

    In humans, systemic heme homeostasis is achieved via coordinated regulation of heme synthesis, transport and degradation. Although the heme biosynthesis and degradation pathways have been well characterized, the pathways for heme trafficking and incorporation into hemoproteins remains poorly understood. In the past few years, researchers have exploited genetic, cellular and biochemical tools, to identify heme transporters and, in the process, reveal unexpected functions for this elusive group of proteins. However, given the complexity of heme trafficking pathways, current knowledge of heme transporters is fragmented and sometimes contradictory. This review seeks to focus on recent studies on heme transporters with specific emphasis on their functions during erythropoiesis. PMID:23415705

  16. Hopping transport in solids

    CERN Document Server

    Pollak, M

    1991-01-01

    The hopping process, which differs substantially from conventional transport processes in crystals, is the central process in the transport phenomena discussed in this book. Throughout the book the term ``hopping'' is defined as the inelastic tunneling transfer of an electron between two localized electronic states centered at different locations. Such processes do not occur in conventional electronic transport in solids, since localized states are not compatible with the translational symmetry of crystals.The rapid growth of interest in hopping transport has followed in the footsteps of the

  17. Canadian pipeline transportation system : transportation assessment

    International Nuclear Information System (INIS)

    2009-07-01

    In addition to regulating the construction and operation of 70,000 km of oil and natural gas pipelines in Canada, the National Energy Board (NEB) regulates the trade of natural gas, oil and natural gas liquids. This report provided an assessment of the Canadian hydrocarbon transportation system in relation to its ability to provide a robust energy infrastructure. Data was collected from NEB-regulated pipeline companies and a range of publicly available sources to determine if adequate pipeline capacity is in place to transport products to consumers. The NEB also used throughput and capacity information received from pipeline operators as well as members of the investment community. The study examined price differentials compared with firm service tolls for transportation paths, as well as capacity utilization on pipelines and the degree of apportionment on major oil pipelines. This review indicated that in general, the Canadian pipeline transportation system continues to work effectively, with adequate pipeline capacity in place to move products to consumers who need them. 9 tabs., 30 figs., 3 appendices.

  18. Passenger transport research

    CSIR Research Space (South Africa)

    Mokonyama, Mathetha T

    2008-03-01

    Full Text Available In South Africa, airport and airline services epitomise what many would like to see in everyday public transport. The CSIR investigates what it will take to provide a commercial public transport service in South Africa which resembles commercial air...

  19. Bronchial mucus transport

    NARCIS (Netherlands)

    van der Schans, Cees P.

    Effective clearance of inhaled particles requires mucus production and continuous mucus transport from the lower airways to the oropharynx. Mucus production takes place mainly in the peripheral airways. Mucus transport is achieved by the action of the ciliated cells that cover the inner surface of

  20. Biofuels for sustainable transportation

    Energy Technology Data Exchange (ETDEWEB)

    Neufeld, S.

    2000-05-23

    Biomass is an attractive energy source, and transportation fuels made from biomass offer a number of benefits. Developing the technology to produce and use biofuels will create transportation fuel options that can positively impact the national energy security, the economy, and the environment. Biofuels include ethanol, methanol, biodiesel, biocrude, and methane.

  1. Emissions of road transport

    International Nuclear Information System (INIS)

    Maekelae, K.; Tuominen, A.

    2001-01-01

    Information on the emissions and energy consumption of different vehicles per transported amount of goods has up to last years been minimal. The unit emissions mean the amount of harmful compounds in the flue gases of a vehicle per service, time or energy unit. National three-year MOBILE 2-research program, started in 1999, determines the unit emissions of all the traffic sectors in Finland. VTT Building and Transport mainly carry out the research, but the Institute of Transportation Engineering of the Tampere University of Technology (TTKK) is responsible for a part of the research. The objective of the project is to create common rules for the determination of unit emissions values, and to determine the best possible values for Finnish conditions. Unit emission data is mainly needed for evaluation of the environmental impacts of production plants and other activities containing transportation of commodities. At the web sites of VTT Building and Transport there are about 60 pages of text and tables (about 4000 values) on unit emissions. The URL of the pages is http://www.vtt.fi/rte/projects/lipastoe/index.htm. These web pages present data on all the transportation sectors (road, railroad, water and air transportation), most of the materials concerning road transportation. Following compounds and values are included: CO, HC, NO x , particulates, SO 2 , CO 2 and energy consumption. Methane and nitrous oxide emissions values have also been presented

  2. Trajectory structures and transport

    International Nuclear Information System (INIS)

    Vlad, Madalina; Spineanu, Florin

    2004-01-01

    The special problem of transport in two-dimensional divergence-free stochastic velocity fields is studied by developing a statistical approach, the nested subensemble method. The nonlinear process of trapping determined by such fields generates trajectory structures whose statistical characteristics are determined. These structures strongly influence the transport

  3. Porters and neurotransmitter transporters

    NARCIS (Netherlands)

    Nelson, Nathan; Lill, H

    1994-01-01

    Uptake of neurotransmitters involves multiple transporters acting in different brain locations under different physiological conditions. The vesicular transporters are driven by a proton-motive force generated by a V-ATPase and their substrates are taken up via proton/substrate exchange. The plasma

  4. Nuclear materials transportation

    International Nuclear Information System (INIS)

    Ushakov, B.A.

    1986-01-01

    Various methods of nuclear materials transportation at different stages of the fuel cycle (U 3 O 8 , UF 6 production enrichment, fuel element manufacturing, storage) are considered. The advantages and drawbacks of railway, automobile, maritime and air transport are analyzed. Some types of containers are characterized

  5. Human peptide transporters

    DEFF Research Database (Denmark)

    Nielsen, Carsten Uhd; Brodin, Birger; Jørgensen, Flemming Steen

    2002-01-01

    Peptide transporters are epithelial solute carriers. Their functional role has been characterised in the small intestine and proximal tubules, where they are involved in absorption of dietary peptides and peptide reabsorption, respectively. Currently, two peptide transporters, PepT1 and PepT2, wh...

  6. Transport of plutonium nitrate

    International Nuclear Information System (INIS)

    1982-02-01

    This leaflet discusses the subject under the headings: why do we need plutonium; why must we transport it; what action is carried out; how is it moved; what are the risks. The transport of the material in specially designed containers, from Dounreay in Caithness by road and sea to Sellafield in Cumbria, is described. (U.K.)

  7. Electronic transport properties

    International Nuclear Information System (INIS)

    Young, W.H.

    1985-01-01

    The theory of the electron transport properties of liquid alkali metals is described. Conductivity coefficients, Boltzmann theory, Ziman theory, alkali form factors, Ziman theory and alkalis, Faber-Ziman alloy theory, Faber-Ziman theory and alkali-alkali methods, status of Ziman theory, and other transport properties, are all discussed. (UK)

  8. Transport and Sustainability

    DEFF Research Database (Denmark)

    Jørgensen, Kaj

    1997-01-01

    Ph.D. study of the scope for sustainable transport in Denmark, and particularly of the role of the motor vehicle in this context. The distribution of groceries is used as case study of the introduction of the motor vehicle in Denmark, concluding that this has resulted in increases of the transport...

  9. Macropores and macropore transport

    DEFF Research Database (Denmark)

    Iversen, Bo Vangsø; Lamandé, Mathieu; Torp, Søren Bent

    2012-01-01

    Preferential transport of water through soil macropores is a governing process in the facilitated transport of strongly sorbing compounds. The aim of this study was to investigate the relationships between macropore density and the hydraulic conductivity of the soil and to test the sampling...

  10. Transport in the Nordic countries

    International Nuclear Information System (INIS)

    Gustafsson, B.; Pettersson, S.; Vilkamo, S.

    1989-01-01

    Transport of radioactive material from different fields of operation is well advanced in the Nordic countries: waste from the medical sector, industry, research, and now in increasing amounts from reactor operation, including spent fuel. In the future, waste from decommissioning will also be transported. This report gives the amount of radioactive waste material to be transported in the Nordic countries. Transport routes, transport containers, and transport systems are described. Legislations and transport regulatins are discussed. (author)

  11. Random Fill Cache Architecture (Preprint)

    Science.gov (United States)

    2014-10-01

    h264ref sjeng milc hmmer lbm libquantum M P K I [0,0] [0,1] [0,3] [0,7] [0,15] [0,31] [-1,0] [-2,1] [-4,3] [-8,7] [-16,15](a) 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3...1.4 1.5 1.6 astar bzip2 h264ref sjeng milc hmmer lbm libquantum N o rm al iz e d IP C [0,0] [0,1] [0,3] [0,7] [0,15] [0,31] [-1,0] [-2,1] [-4,3...perform well under demand fetch. For example, lots of irregular streaming access patterns can be found in libquantum and lbm , which shows wider spatial

  12. National Utility Rate Database: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ong, S.; McKeel, R.

    2012-08-01

    When modeling solar energy technologies and other distributed energy systems, using high-quality expansive electricity rates is essential. The National Renewable Energy Laboratory (NREL) developed a utility rate platform for entering, storing, updating, and accessing a large collection of utility rates from around the United States. This utility rate platform lives on the Open Energy Information (OpenEI) website, OpenEI.org, allowing the data to be programmatically accessed from a web browser, using an application programming interface (API). The semantic-based utility rate platform currently has record of 1,885 utility rates and covers over 85% of the electricity consumption in the United States.

  13. Energy from Offshore Wind: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Musial, W.; Butterfield, S.; Ram, B.

    2006-02-01

    This paper provides an overview of the nascent offshore wind energy industry including a status of the commercial offshore industry and the technologies that will be needed for full market development.

  14. How Nano are Nanocomposites (Preprint)

    National Research Council Canada - National Science Library

    Schafer, Dale W; Justice, Ryan S

    2007-01-01

    ...s (single and multi-walled), and layered silicates. The conclusion is that large-scale disorder is ubiquitous in nanocomposites regardless of the level of dispersion, leading to substantial reduction of mechanical properties (modulus) compared to predictions based on idealized filler morphology.

  15. Hiding Crimes in Cyberspace (PREPRINT)

    National Research Council Canada - National Science Library

    Denning, Dorothy E; Baugh, Jr, William E

    1999-01-01

    .... Individuals need it to protect their private communications and confidential data. Encryption is critical to building a secure and trusted global information infrastructure for communications and electronic commerce...

  16. On NEO Threat Mitigation (Preprint)

    Science.gov (United States)

    2007-10-15

    Yucatan event is at least a major contributor, if not the direct cause of the extinction of the dinosaurs . Moreover, it is clear that NEO impacts can... extinction of the human race. The probability of these events decreases with the severity of the impact, and size (mass) of the NEO. Figure 1 and Table 1...thus, it is more reasonable to infer that all the large NEOs can be catalogued within a reasonable time, while smaller and less consequential

  17. Planning Public Transport

    DEFF Research Database (Denmark)

    Andersen, Jonas Lohmann Elkjær; Landex, Alex

    2009-01-01

    This good practice guide is composed for the master course 13120 Public Transport Planning held at the Department of Transport, Technical University of Denmark. It is intended to use as guide in the different planning aspects and assignments of the course. Since the course is about the planning...... of new public transport infrastructure this guide also focuses on the planning of new infrastructure. Furthermore, the new infrastructure in the course is expected to be a light rail and even though this guide aims at being general for public transport some of the issues evidently become more relevant...... will enable a capability for planning both bus and rail. The guide is build as a full sketch investigation of a new public transport project ranging chronological from project clarification to physical and timetable planning to traffic modeling and project appraisal. The same steps that are expected...

  18. Porters and neurotransmitter transporters.

    Science.gov (United States)

    Nelson, N; Lill, H

    1994-11-01

    Uptake of neurotransmitters involves multiple transporters acting in different brain locations under different physiological conditions. The vesicular transporters are driven by a proton-motive force generated by a V-ATPase and their substrates are taken up via proton/substrate exchange. The plasma membrane transporters are driven by an electrochemical gradient of sodium generated by a Na+/K(+)-ATPase. Two distinct families of transporters were identified in this group. One cotransports sodium with glutamate and other amino acids and requires additionally an outwardly directed potassium gradient. The second cotransports sodium, chloride and a variety of neurotransmitters, including gamma-aminobutyric acid (GABA), glycine and monoamines. Genes and cDNA encoding several members of the latter family have been cloned and studied in detail. The structure and function as well as the evolutionary relationships among these neurotransmitter transporters are discussed.

  19. Fuel transporting device

    International Nuclear Information System (INIS)

    Shiratori, Hirozo.

    1979-01-01

    Purpose: In a liquid-metal cooled reactor, to reduce the waiting time of fuel handling apparatuses and shorten the fuel exchange time. Constitution: A fuel transporting machine is arranged between a reactor vessel and an out-pile storage tank, thereby dividing the transportation line of the pot for contracting fuel and transporting the same. By assuming such a construction, the flow of fuel transportation which has heretofore been carried out through fuel transportation pipes is not limited to one direction but the take-out of fuels from the reactor and the take-in thereof from the storage tank can be carried out constantly, and much time is not required for fuel exchange. (Kamimura, M.)

  20. Fuelling tomorrow's transport

    International Nuclear Information System (INIS)

    Cadwallader, S.; Donovan, N.

    1995-11-01

    Fuelling Tomorrow's Transport provides a thorough analysis of key industry trends; developments in technology, fuel use and efficiency; environmental and legislative constraints; and company and governmental policy. It discusses in detail the changes facing the transport industry and analyses how the various technological, political and economic developments will affect the industry into the next century. Key issues addressed include: current and future fuel use in road, marine and aviation transport; growth in the transport sector and the impact on the oil market; likely scenarios for future transport fuelling; the latest developments in alternative fuels and engines, including electricity, natural gas, nuclear power and liquid hydrogen, and the commercial feasibility of these technologies; government policy and current and proposed legislative and fiscal incentives for the development and take-up of alternative fuels and engines; the driving force of the environmental debate; the current research and development programmes of individual companies; and the commercial openings offered by these developments. (author)

  1. Transport, environment and sustainability

    DEFF Research Database (Denmark)

    Joumard, Robert; Gudmundsson, Henrik; Kehagia, Fotini

    2010-01-01

    This report is the final report of the action COST 356 'EST - Towards the definition of a measurable environmentally sustainable transport'. It tries to answer the following questions: How can environmental impacts of transport be measured? How can measurements be transformed into operational...... indicators? How can several indicators be jointly considered? And how can indicators be used in planning and decision making? Firstly we provide definition of 'indicator of environmental sustainability in transport'. The functions, strengths and weaknesses of indicators as measurement tools, and as decision...... support tools are discussed. We define what "environmental sustainability in transport" may mean through the transport system, the concepts of sustainable development and of environment. The concept of 'chain of causality' between a source and a final target is developed, as a common reference...

  2. Logistic innovations in transport

    Directory of Open Access Journals (Sweden)

    Mirosław Antonowicz

    2014-03-01

    Full Text Available Introduction: The article discusses the issue of logistic innovations in transport. The essentials of logistic innovations in transport together with some examples of specific innovations are presented. The role of the client's needs in transport innovations is indicated. The most vital postulates affecting the innovativeness of shipping companies and derived from the author's experience as well as scholarly publications, are time, safety, reliability as well as comprehensiveness of service offer. Following the analysis of the issue, and on the grounds of Kaizen's and Lean's method, the concept of continuous innovations is suggested as very useful for the development of transport. The potential of clusters as the source of logistic innovations in transport is emphasised. Methods: The discussion of the issue was preceded by the author's analysis of written sources on innovativeness, the evaluation of ratings of innovativeness as well as the analysis of rewarded innovative solutions in transport subsequent to the businesses participation in the programme of innovative solutions in transport. The role of innovation practical business operations is argued following the analysis of some strategic documents such as: 2011 White Paper and the Strategy for the Development of Transport by 2020 adopted by the Polish government in 2013. Aim: The aim of the article is to present the role and significance of the issue of logistic innovations in transport and to cite instances of practical solutions implemented by shipping companies, the solutions which resulted in measurable effects. Following the author's observation of the instances of innovative solutions as well as his analysis of the ratings of innovativeness, the article aims to present the conclusions as for the specific kinds of activities which are indispensable to foster innovativeness in transport. Conclusions: The conclusions derived from the author's analyses and observations show that logistic

  3. Transportation Consumer Education Curriculum Guide.

    Science.gov (United States)

    Finn, Peter; And Others

    Materials in this curriculum guide represent a selection of the major transportation consumer topics and ideas and are designed to set the stage for more intensive transportation consumer education curriculum development and teacher efforts. (Eleven manuals covering the four transportation topics of public transportation, transportation and the…

  4. Children and transportation

    Energy Technology Data Exchange (ETDEWEB)

    Anon

    2003-12-09

    This issue of the 'Sustainable Transportation Monitor', published by the Centre for Sustainable Transportation located in Mississauga, Ontario, reports on key findings from a project involving children and transportation in the Halton and Peel regions of Ontario, recently completed by the Centre. Excerpts from the report summarized in this issue include data on children's travel in Halton and Peel, and a discussion on possible contribution of transport practices to the growing incidence of obesity among Canadian children. Results of the study indicate that until about age 18, travel by children on schooldays is dominated by the journey to and from school. School bus is the choice of 28 per cent, and passenger car by 23 per cent among 11-to-14- year-olds; the share of travel by car is larger for older young people and also likely larger among 6-to-10-year-olds. Physical inactivity has been highlighted as the contributing factor to excess body weight and obesity in this, and other studies. Data collected for this study corroborates the findings of other studies by showing a positive correlation between obesity and transport energy use in 18 affluent countries, suggesting that a high level of use of motorized transport contributes to inactivity and body weight gain. Several alternate means of transportation, with the potential to combat obesity, are proposed. 46 refs.

  5. Canadian hydrocarbon transportation system : transportation assessment

    International Nuclear Information System (INIS)

    2006-06-01

    This document provided an assessment of the Canadian hydrocarbon transportation system. In addition to regulating the construction and operation of Canada's 45,000 km of pipeline that cross international and provincial borders, Canada's National Energy Board (NEB) regulates the trade of natural gas, oil and natural gas liquids. The ability of pipelines to delivery this energy is critical to the country's economic prosperity. The pipeline system includes large-diameter, cross-country, high-pressure natural gas pipelines, low-pressure crude oil and oil products pipelines and small-diameter pipelines. In order to assess the hydrocarbon transportation system, staff at the NEB collected data from pipeline companies and a range of publicly available sources. The Board also held discussions with members of the investment community regarding capital markets and emerging issues. The assessment focused largely on evaluating whether Canadians benefit from an efficient energy infrastructure and markets. The safety and environmental integrity of the pipeline system was also evaluated. The current adequacy of pipeline capacity was assessed based on price differentials compared with firm service tolls for major transportation paths; capacity utilization on pipelines; and, the degree of apportionment on major oil pipelines. The NEB concluded that the Canadian hydrocarbon transportation system is working effectively, with an adequate capacity in place on existing natural gas pipelines, but with a tight capacity on oil pipelines. It was noted that shippers continue to indicate that they are reasonably satisfied with the services provided by pipeline companies and that the NEB-regulated pipeline companies are financially stable. 14 refs, 11 tabs., 28 figs., 4 appendices

  6. Transports and environment; Transports et environnements

    Energy Technology Data Exchange (ETDEWEB)

    Anon,

    2004-07-01

    In the framework of the greenhouse gases reduction, this study proposes many advices to control the fuel consumption of the vehicles and to change habits in the transportation sector. It presents also the alternatives to the pollutant today vehicles in the domain of the vehicles and buses fuels but also the new motors. Many Internet addresses are provided to complete the presentation. (A.L.B.)

  7. Transport of hazardous goods

    International Nuclear Information System (INIS)

    1989-01-01

    The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

  8. TRANSPORTATION SYSTEM REQUIREMENTS DOCUMENT

    International Nuclear Information System (INIS)

    2004-01-01

    This document establishes the Transportation system requirements for the U.S. Department of Energy's (DOE's) Civilian Radioactive Waste Management System (CRWMS). These requirements are derived from the Civilian Radioactive Waste Management System Requirements Document (CRD). The Transportation System Requirements Document (TSRD) was developed in accordance with LP-3.1Q-OCRWM, Preparation, Review, and Approval of Office of National Transportation Level-2 Baseline Requirements. As illustrated in Figure 1, the TSRD forms a part of the DOE Office of Civilian Radioactive Waste Management (OCRWM) Technical Baseline

  9. Transport in stellarators

    International Nuclear Information System (INIS)

    Maassberg, H.; Brakel, R.; Burhenn, R.; Gasparino, U.; Grigull, P.; Kick, M.; Kuehner, G.; Ringler, H.; Sardei, F.; Stroth, U.; Weller, A.

    1993-01-01

    The local electron and ion heat transport as well as the particle and impurity transport properties in stellarators are reviewed. In this context, neoclassical theory is used as a guideline for the comparison of the experimental results of the quite different confinement concepts. At sufficiently high temperatures depending on the specific magnetic configuration, neoclassical predictions are confirmed by experimental findings. The confinement properties in the LMFP collisionality regime are discussed with respect to the next stellarator generation, for which at higher temperatures the neoclassical transport is expected to become more important. (orig.)

  10. CNG transport opportunities

    International Nuclear Information System (INIS)

    Anon

    2000-01-01

    The recent announcement by the Australian Government of funding for a dramatic increase in supply infrastructure for Compressed Natural Gas (CNG) powered vehicles has shored up predictions that natural gas will achieve a thirty-fold increase in its share of the Australian transport energy market by 2015. This projection, would put sales of natural gas for transport fuel in the year 2014/15 at about 10% of current retail sales across the nation. In the general transport sector, the lower particulate and noise pollution, compared with diesel-powered vehicles, is a significant advantage

  11. Means of Transport

    DEFF Research Database (Denmark)

    Balle, Søren Hattesen

    The car is probably one of the most central signifiers of modern scientific and technological progress. Not only did its introduction in early 20th century America quite literally move scientific progress into the street, it also provided its increasing number of users with new and technologically....... According to film theorist Julian Smith, the automobile has been just as much “embraced … as a form of emotional transport, the state or condition of being transported by ecstasy” as “perceived as a mode of transportation in the primary and ordinary sense of the word.” This paper analyses the ways in which...

  12. Transport Coefficients of Fluids

    CERN Document Server

    Eu, Byung Chan

    2006-01-01

    Until recently the formal statistical mechanical approach offered no practicable method for computing the transport coefficients of liquids, and so most practitioners had to resort to empirical fitting formulas. This has now changed, as demonstrated in this innovative monograph. The author presents and applies new methods based on statistical mechanics for calculating the transport coefficients of simple and complex liquids over wide ranges of density and temperature. These molecular theories enable the transport coefficients to be calculated in terms of equilibrium thermodynamic properties, and the results are shown to account satisfactorily for experimental observations, including even the non-Newtonian behavior of fluids far from equilibrium.

  13. EBS Radionuclide Transport Abstraction

    Energy Technology Data Exchange (ETDEWEB)

    J.D. Schreiber

    2005-08-25

    The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in ''Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration'' (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment for the license application (TSPA-LA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA-LA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport

  14. EBS Radionuclide Transport Abstraction

    International Nuclear Information System (INIS)

    J.D. Schreiber

    2005-01-01

    The purpose of this report is to develop and analyze the engineered barrier system (EBS) radionuclide transport abstraction model, consistent with Level I and Level II model validation, as identified in ''Technical Work Plan for: Near-Field Environment and Transport: Engineered Barrier System: Radionuclide Transport Abstraction Model Report Integration'' (BSC 2005 [DIRS 173617]). The EBS radionuclide transport abstraction (or EBS RT Abstraction) is the conceptual model used in the total system performance assessment for the license application (TSPA-LA) to determine the rate of radionuclide releases from the EBS to the unsaturated zone (UZ). The EBS RT Abstraction conceptual model consists of two main components: a flow model and a transport model. Both models are developed mathematically from first principles in order to show explicitly what assumptions, simplifications, and approximations are incorporated into the models used in the TSPA-LA. The flow model defines the pathways for water flow in the EBS and specifies how the flow rate is computed in each pathway. Input to this model includes the seepage flux into a drift. The seepage flux is potentially split by the drip shield, with some (or all) of the flux being diverted by the drip shield and some passing through breaches in the drip shield that might result from corrosion or seismic damage. The flux through drip shield breaches is potentially split by the waste package, with some (or all) of the flux being diverted by the waste package and some passing through waste package breaches that might result from corrosion or seismic damage. Neither the drip shield nor the waste package survives an igneous intrusion, so the flux splitting submodel is not used in the igneous scenario class. The flow model is validated in an independent model validation technical review. The drip shield and waste package flux splitting algorithms are developed and validated using experimental data. The transport model considers

  15. NJ transportation fact book, 2007

    Science.gov (United States)

    2010-01-01

    The New Jersey Transportation Fact Book 2006-07 presents information about the New Jersey Department of Transportation : and other agencies that provide transportation services in New Jersey. We hope it will prove helpful.

  16. National Transportation Atlas Databases : 2013.

    Science.gov (United States)

    2013-01-01

    The National Transportation Atlas Databases 2013 (NTAD2013) is a set of nationwide geographic datasets of transportation facilities, transportation networks, associated infrastructure, and other political and administrative entities. These datasets i...

  17. National Transportation Atlas Databases : 2015.

    Science.gov (United States)

    2015-01-01

    The National Transportation Atlas Databases 2015 (NTAD2015) is a set of nationwide geographic datasets of transportation facilities, transportation networks, associated infrastructure, and other political and administrative entities. These datasets i...

  18. National Transportation Atlas Databases : 2012.

    Science.gov (United States)

    2012-01-01

    The National Transportation Atlas Databases 2012 (NTAD2012) is a set of nationwide geographic databases of transportation facilities, transportation networks, and associated infrastructure. These datasets include spatial information for transportatio...

  19. National Transportation Atlas Databases : 2011.

    Science.gov (United States)

    2011-01-01

    The National Transportation Atlas Databases 2011 (NTAD2011) is a set of nationwide geographic databases of transportation facilities, transportation networks, and associated infrastructure. These datasets include spatial information for transportatio...

  20. National Transportation Atlas Databases : 2009.

    Science.gov (United States)

    2009-01-01

    The National Transportation Atlas Databases 2009 (NTAD2009) is a set of nationwide geographic databases of transportation facilities, transportation networks, and associated infrastructure. These datasets include spatial information for transportatio...

  1. National Transportation Atlas Databases : 2014.

    Science.gov (United States)

    2014-01-01

    The National Transportation Atlas Databases 2014 (NTAD2014) is a set of nationwide geographic datasets of transportation facilities, transportation networks, associated infrastructure, and other political and administrative entities. These datasets i...

  2. National Transportation Atlas Databases : 2010.

    Science.gov (United States)

    2010-01-01

    The National Transportation Atlas Databases 2010 (NTAD2010) is a set of nationwide geographic databases of transportation facilities, transportation networks, and associated infrastructure. These datasets include spatial information for transportatio...

  3. Development of Indian passenger transport

    Energy Technology Data Exchange (ETDEWEB)

    Ramanathan, R. [Indira Ghandi Institute of Development Research, Mumbai (India)

    1998-05-01

    The Indian transport sector has been studied using logistic substitution. The share of rail transport is declining, while road and air transport are increasing. These developments are not desirable from an energy-efficiency perspective. (author)

  4. Transportation statistics annual report 2010

    Science.gov (United States)

    2011-01-01

    The Transportation Statistics Annual Report (TSAR) presents data and information compiled by the Bureau of Transportation Statistics (BTS), a component of the U.S. Department of Transportations (USDOTs) Research and Innovative Technology Admini...

  5. Transportation statistics annual report 2009

    Science.gov (United States)

    2009-01-01

    The Transportation Statistics Annual Report (TSAR) presents data and information selected by the Bureau of Transportation Statistics (BTS), a component of the U.S. Department of Transportation's (USDOT's) Research and Innovative Technology Administra...

  6. Pocket Guide to Transportation 2012

    Science.gov (United States)

    2012-01-01

    The Bureau of Transportation Statistics (BTS) of the Research and Innovative Technology Administration produces the Pocket Guide to Transportation as a compact resource that provides snapshots of the U.S. transportation system and highlights major tr...

  7. Pocket Guide to Transportation 2018

    Science.gov (United States)

    2018-01-01

    The 2018 BTS Pocket Guide to Transportation is a quick reference guide that provides transportation statistics at your fingertips. It provides key information and highlights major trends on the U.S. transportation system. This year features a new and...

  8. Accident resistant transport container

    Science.gov (United States)

    Anderson, J.A.; Cole, K.K.

    The invention relates to a container for the safe air transport of plutonium having several intermediate wood layers and a load spreader intermediate an inner container and an outer shell for mitigation of shock during a hypothetical accident.

  9. Molecular electronic junction transport

    DEFF Research Database (Denmark)

    Solomon, Gemma C.; Herrmann, Carmen; Ratner, Mark

    2012-01-01

    Whenasinglemolecule,oracollectionofmolecules,isplacedbetween two electrodes and voltage is applied, one has a molecular transport junction. We discuss such junctions, their properties, their description, and some of their applications. The discussion is qualitative rather than quantitative, and f...

  10. Transportation energy data book

    Science.gov (United States)

    2009-01-01

    The Transportation Energy Data Book: Edition 28 is a statistical compendium prepared and : published by Oak Ridge National Laboratory (ORNL) under contract with the U.S. Department of : Energy, Office of Energy Efficiency and Renewable Energy, Vehicl...

  11. Interfacial transport phenomena

    CERN Document Server

    Slattery, John C; Oh, Eun-Suok

    2007-01-01

    Revised and updated extensively from the previous editionDiscusses transport phenomena at common lines or three-phase lines of contactProvides a comprehensive summary about the extensions of continuum mechanics to the nanoscale.

  12. Transport of radioactive materials

    International Nuclear Information System (INIS)

    1988-07-01

    The norm which establishes the requirements of radiation protection and safety related to the transport of radioactive materials, aiming to keep a suitable control level of eventual exposure of personnels, materials and environment of ionizing radiation, including: specifications on radioactive materials for transport, selection of package type; specification of requirements of the design and assays of acceptance of packages; disposal related to the transport; and liability and administrative requirements, are presented. This norm is applied to: truckage, water carriage and air service; design, fabrication, assays and mantenaince of packages; preparation, despatching, handling, loading storage in transition and reception in the ultimate storage of packages; and transport of void packages which have been contained radioactive materials. (M.C.K.) [pt

  13. Transport and the environment

    Energy Technology Data Exchange (ETDEWEB)

    Sharp, C; Jennings, T

    1976-01-01

    This book examines the impact of transport operations on the environment. Noise, air pollution, vibration, accidents, delays caused by slow-moving vehicles, road wear, visual intrusion, the severance of communities--all these social costs of transport are studied, together with policies that might reduce them. The difficulties in measuring costs and benefits and the value judgments that may guide transport policy are reviewed. Specific problems examined include the journey to work, traffic-free shopping streets, urban motor-ways, and inter-change depots for goods vehicles. The role of central and local government is considered, particular attention being given to methods of allowing for environmental benefits when planning new transport investment; the implications of EEC policy are also noted.

  14. Transportation Network Topologies

    Science.gov (United States)

    Alexandrov, Natalia (Editor)

    2004-01-01

    The existing U.S. hub-and-spoke air transportation system is reaching saturation. Major aspects of the current system, such as capacity, safety, mobility, customer satisfaction, security, communications, and ecological effects, require improvements. The changing dynamics - increased presence of general aviation, unmanned autonomous vehicles, military aircraft in civil airspace as part of homeland defense - contributes to growing complexity of airspace. The system has proven remarkably resistant to change. NASA Langley Research Center and the National Institute of Aerospace conducted a workshop on Transportation Network Topologies on 9-10 December 2003 in Williamsburg, Virginia. The workshop aimed to examine the feasibility of traditional methods for complex system analysis and design as well as potential novel alternatives in application to transportation systems, identify state-of-the-art models and methods, conduct gap analysis, and thus to lay a foundation for establishing a focused research program in complex systems applied to air transportation.

  15. Modelling Ballast Water Transport

    Digital Repository Service at National Institute of Oceanography (India)

    Jayakumar, S.; Babu, M.T.; Vethamony, P.

    Ballast water discharges in the coastal environs have caused a great concern over the recent periods as they account for transporting marine organisms from one part of the world to the other. The movement of discharged ballast water as well...

  16. Transportation Industry 2004

    National Research Council Canada - National Science Library

    Miller, Evan; Kathir, Nathan; Brogan, Dennis M

    2004-01-01

    ... and the environment in which the private sector operates. They must also assess the role of government in determining transportation policy, as federal, state, and local agencies regulate every mode of this industry. While the U.S...

  17. Transportation Security Administration

    Science.gov (United States)

    ... content Official website of the Department of Homeland Security Transportation Security Administration A - Z Index Blog What Can I ... Search form Search the Site Main menu Travel Security Screening Special Procedures TSA Pre✓® Passenger Support Travel ...

  18. Remote controlled transport device

    International Nuclear Information System (INIS)

    Nakahira, Masataka; Oka, Kiyoshi; Ito, Akira; Tada, Eisuke; Sato, Masaki

    1998-01-01

    The present invention provides a device for transporting equipments for maintenance and parts between a maintenance port and a facility for maintenance by remote control in a radioactive material handling facility such as a nuclear power plant. Namely, a power supply bus bar is disposed along a transferring path in order to supply power to a transporting means, and is divided into every region having a predetermined length. Each of the power supply bus bar regions is controlled for the power supply by a control device. Accordingly, the transporting means can be moved and driven successively being independent on every power supply bus bar region. Accordingly, a plurality of transporting means can be operated independently in a transferring path without laying around power cables and control signal cables. (I.S.)

  19. Active transport and heat.

    Science.gov (United States)

    Tait, Peter W

    2011-07-01

    Increasing heat may impede peoples' ability to be active outdoors thus limiting active transport options. Co-benefits from mitigation of and adaptation to global warming should not be assumed but need to be actively designed into strategies.

  20. Transportation and Tourism

    Science.gov (United States)

    2012-08-01

    This project explored the link between transportation and tourism in Texas. A session on transit and tourism was organized and conducted as part of the 2012 Texas Transit Conference. Speakers at the session described public transit services oriented ...

  1. Risicobeheersing transport diervoeders

    NARCIS (Netherlands)

    Meijer, G.A.L.; Houwers, H.W.J.; Ipema, A.H.; Boekhoff, M.

    2007-01-01

    Welke knelpunten en oplossingsrichtingen bestaan in de praktijk van het transport diervoeders met betrekking tot de implementatie van de diervoederhygiëneverordening, toegespitst op informatievoorziening over wettelijke en bovenwettelijke eisen, naleving, controle en handhaving?

  2. Offsite transportation hazards assessment

    International Nuclear Information System (INIS)

    Burnside, M.E.

    1997-01-01

    This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

  3. Manpower and Transportation Planning

    NARCIS (Netherlands)

    Lai, S.W.

    2014-01-01

    This thesis studies three routing and scheduling problems arising in manpower and transportation planning. These problems are rooted in real applications, and carry interesting characteristics. By exploiting the structures of the problems, this thesis provides effective mathematical models and

  4. Energy and transportation(*

    Directory of Open Access Journals (Sweden)

    Hermans J.

    2015-01-01

    Full Text Available Transportation takes a considerable and increasing fraction of the energy use worldwide, and more than half the oil consumption. By far the largest part is used by cars powered by internal combustion engines. The advantage of using internal combustion engines is that the energy density of liquid fuels is extremely high. The disadvantage is that gasoline and diesel engines have a poor performance: 20 to 25% only. How does this compare with electric cars? What are the alternative transportation systems and their efficiencies anyway? In this lecture we analyse the efficiency of various transport systems, using elementary physics principles. We will look at cars, buses, trains and TGVs, ships and aircraft. In addition, the efficiency of human powered vehicles will be considered. New and promising developments in the field of Intelligent Transportation Systems, like Cooperative Adaptive Cruise Control, are also discussed.

  5. MANAGEMENT OF TOURISM TRANSPORT

    Directory of Open Access Journals (Sweden)

    Gabriela Cecilia STĂNCIULESCU

    2016-06-01

    Full Text Available Undoubtedly, the relevance of transport activities in relation to tourism activities is essential, because it is extremely important and necessary to offer feasible information about tourism services to help consumer to choose the mode of travel to destinations ideal holiday. The methods used in the development of this hypothesis were explanation, exemplification (brief presentation of each mode of transport comparison etc. Analyzing the current situation of national, European and World Wide tourism transportation, the paper proposes practical applications able to explain that the conduct of economic activities as an integral part of the sector of trade and services within a national economy, would not be possible without the involvement of transport, whether by road, rail and air and naval. The results of the analysis are perfectly applicable offering guests the opportunity to reach the most remote corners of the world in a short time, high degree of comfort and affordable price.

  6. Crew Transportation Operations Standards

    Science.gov (United States)

    Mango, Edward J.; Pearson, Don J. (Compiler)

    2013-01-01

    The Crew Transportation Operations Standards contains descriptions of ground and flight operations processes and specifications and the criteria which will be used to evaluate the acceptability of Commercial Providers' proposed processes and specifications.

  7. Accident resistant transport container

    International Nuclear Information System (INIS)

    Andersen, J.A.; Cole, J.K.

    1980-01-01

    The invention relates to a container for the safe air transport of plutonium having several intermediate wood layers and a load spreader intermediate an inner container and an outer shell for mitigation of shock during a hypothetical accident

  8. Cooperative Transport Planning

    NARCIS (Netherlands)

    Zutt, J.; De Weerdt, M.M.

    2000-01-01

    To test and compare different forms of cooperative planning algorithms developed in the CABS project we use a generic simulator called MARS. Examples in the transportation sector are implemented in this simulator.

  9. Energy and transportation(*)

    Science.gov (United States)

    Hermans, J.

    2015-08-01

    Transportation takes a considerable and increasing fraction of the energy use worldwide, and more than half the oil consumption. By far the largest part is used by cars powered by internal combustion engines. The advantage of using internal combustion engines is that the energy density of liquid fuels is extremely high. The disadvantage is that gasoline and diesel engines have a poor performance: 20 to 25% only. How does this compare with electric cars? What are the alternative transportation systems and their efficiencies anyway? In this lecture we analyse the efficiency of various transport systems, using elementary physics principles. We will look at cars, buses, trains and TGVs, ships and aircraft. In addition, the efficiency of human powered vehicles will be considered. New and promising developments in the field of Intelligent Transportation Systems, like Cooperative Adaptive Cruise Control, are also discussed.

  10. Transport statistics 1996

    CSIR Research Space (South Africa)

    Shepperson, L

    1997-12-01

    Full Text Available This publication contains transport and related statistics on roads, vehicles, infrastructure, passengers, freight, rail, air, maritime and road traffic, and international comparisons. The information compiled in this publication has been gathered...

  11. CHARTB multigroup transport package

    International Nuclear Information System (INIS)

    Baker, L.

    1979-03-01

    The physics and numerical implementation of the radiation transport routine used in the CHARTB MHD code are discussed. It is a one-dimensional (Cartesian, cylindrical, and spherical symmetry), multigroup,, diffusion approximation. Tests and applications will be discussed as well

  12. Animal transportation networks

    Science.gov (United States)

    Perna, Andrea; Latty, Tanya

    2014-01-01

    Many group-living animals construct transportation networks of trails, galleries and burrows by modifying the environment to facilitate faster, safer or more efficient movement. Animal transportation networks can have direct influences on the fitness of individuals, whereas the shape and structure of transportation networks can influence community dynamics by facilitating contacts between different individuals and species. In this review, we discuss three key areas in the study of animal transportation networks: the topological properties of networks, network morphogenesis and growth, and the behaviour of network users. We present a brief primer on elements of network theory, and then discuss the different ways in which animal groups deal with the fundamental trade-off between the competing network properties of travel efficiency, robustness and infrastructure cost. We consider how the behaviour of network users can impact network efficiency, and call for studies that integrate both network topology and user behaviour. We finish with a prospectus for future research. PMID:25165598

  13. On linear transport problems

    International Nuclear Information System (INIS)

    Ignatovich, V.K.

    1989-01-01

    The equations. governing the transport of radiation in plane media of finite thickness are formulated and solved in terms reflection and extintion of radiation inthe case of semi infinite media. 13 refs

  14. Improved electron transport layer

    DEFF Research Database (Denmark)

    2012-01-01

    The present invention provides: a method of preparing a coating ink for forming a zinc oxide electron transport layer, comprising mixing zinc acetate and a wetting agent in water or methanol; a coating ink comprising zinc acetate and a wetting agent in aqueous solution or methanolic solution......; a method of preparing a zinc oxide electron transporting layer, which method comprises: i) coating a substrate with the coating ink of the present invention to form a film; ii) drying the film; and iii) heating the dry film to convert the zinc acetate substantially to ZnO; a method of preparing an organic...... photovoltaic device or an organic LED having a zinc oxide electron transport layer, the method comprising, in this order: a) providing a substrate bearing a first electrode layer; b) forming an electron transport layer according to the following method: i) coating a coating ink comprising an ink according...

  15. Transportation Network Topologies

    Science.gov (United States)

    Holmes, Bruce J.; Scott, John

    2004-01-01

    A discomforting reality has materialized on the transportation scene: our existing air and ground infrastructures will not scale to meet our nation's 21st century demands and expectations for mobility, commerce, safety, and security. The consequence of inaction is diminished quality of life and economic opportunity in the 21st century. Clearly, new thinking is required for transportation that can scale to meet to the realities of a networked, knowledge-based economy in which the value of time is a new coin of the realm. This paper proposes a framework, or topology, for thinking about the problem of scalability of the system of networks that comprise the aviation system. This framework highlights the role of integrated communication-navigation-surveillance systems in enabling scalability of future air transportation networks. Scalability, in this vein, is a goal of the recently formed Joint Planning and Development Office for the Next Generation Air Transportation System. New foundations for 21st thinking about air transportation are underpinned by several technological developments in the traditional aircraft disciplines as well as in communication, navigation, surveillance and information systems. Complexity science and modern network theory give rise to one of the technological developments of importance. Scale-free (i.e., scalable) networks represent a promising concept space for modeling airspace system architectures, and for assessing network performance in terms of scalability, efficiency, robustness, resilience, and other metrics. The paper offers an air transportation system topology as framework for transportation system innovation. Successful outcomes of innovation in air transportation could lay the foundations for new paradigms for aircraft and their operating capabilities, air transportation system architectures, and airspace architectures and procedural concepts. The topology proposed considers air transportation as a system of networks, within which

  16. Heat transport and storage

    International Nuclear Information System (INIS)

    Despois, J.

    1977-01-01

    Recalling the close connections existing between heat transport and storage, some general considerations on the problem of heat distribution and transport are presented 'in order to set out the problem' of storage in concrete form. This problem is considered in its overall plane, then studied under the angle of the different technical choices it involves. The two alternatives currently in consideration are described i.e.: storage in a mined cavity and underground storage as captive sheet [fr

  17. Transportation and its Infrastructure

    OpenAIRE

    Ribeiro, Suzana K; Kobayashi, Shigeki; Beuthe, Michel; Gasca, Jorge; Greene, David; Lee, David S.; Muromachi, Yasunori; Newton, Peter J.; Plotkin, Steven; Sperling, Daniel; Wit, Ron; Zhou, Peter J

    2007-01-01

    Transport activity, a key component of economic development and human welfare, is increasing around the world as economies grow. For most policymakers, the most pressing problems associated with this increasing transport activity are traffic fatalities and injuries, congestion, air pollution and petroleum dependence. These problems are especially acute in the most rapidly growing economies of the developing world. Mitigating greenhouse gas (GHG) emissions can take its place among these other ...

  18. Transportation of radioactive elements

    International Nuclear Information System (INIS)

    Thubert, Francis; Rentien, Guy; Jacquet, Michel

    1981-01-01

    The production and marketing of artificial radioactive elements engaged in by the 'Office des Rayonnements Ionisants' requires the use of specially designed packagings and assorted means of transport. The authors begin by describing the different kinds of products involved and the forms of packagings needed, and go on to discuss the various means of transport used, underlining the fact that, in terms of number and gravity, the incidents that have occurred to date have indeed been few and far between [fr

  19. Tape transport mechanism

    International Nuclear Information System (INIS)

    Groh, E.F.; McDowell, W.; Modjeski, N.S.; Keefe, D.J.; Groer, P.

    1979-01-01

    A device is provided for transporting, in a stepwise manner, tape between a feed reel and takeup reel. An indexer moves across the normal path of the tape displacing it while the tape on the takeup reel side of the indexer is braked. After displacement, the takeup reel takes up the displaced tape while the tape on the feed reel side of the indexer is braked, providing stepwise tape transport in precise intervals determined by the amount of displacement caused by the indexer

  20. Monitoring of transport contamination

    International Nuclear Information System (INIS)

    Turkin, N.F.

    1980-01-01

    Organization of monitoring of transport contamination is considered. A particularly thorough monitoring is recommended to be carried out in loading-unloading operations. The monitoring is performed when leaving loading-unloading site and zone under control and prior to preventive examination, technical service or repair. The method of monitoring of auto transport contamination with high-energy β-emitters by means of a special stand permitting the automation of the monitoring process is described [ru

  1. Digital intelligence sources transporter

    International Nuclear Information System (INIS)

    Zhang Zhen; Wang Renbo

    2011-01-01

    It presents from the collection of particle-ray counting, infrared data communication, real-time monitoring and alarming, GPRS and other issues start to realize the digital management of radioactive sources, complete the real-time monitoring of all aspects, include the storing of radioactive sources, transporting and using, framing intelligent radioactive sources transporter, as a result, achieving reliable security supervision of radioactive sources. (authors)

  2. Spin transport in nanowires

    OpenAIRE

    Pramanik, S.; bandyopadhyay, S.; Cahay, M.

    2003-01-01

    We study high-field spin transport of electrons in a quasi one-dimensional channel of a $GaAs$ gate controlled spin interferometer (SPINFET) using a semiclassical formalism (spin density matrix evolution coupled with Boltzmann transport equation). Spin dephasing (or depolarization) is predominantly caused by D'yakonov-Perel' relaxation associated with momentum dependent spin orbit coupling effects that arise due to bulk inversion asymmetry (Dresselhaus spin orbit coupling) and structural inve...

  3. Thermoelectric transport in superlattices

    Energy Technology Data Exchange (ETDEWEB)

    Reinecke, T L; Broido, D A

    1997-07-01

    The thermoelectric transport properties of superlattices have been studied using an exact solution of the Boltzmann equation. The role of heat transport along the barrier layers, of carrier tunneling through the barriers, of valley degeneracy and of the well width and energy dependences of the carrier-phonon scattering rates on the thermoelectric figure of merit are given. Calculations are given for Bi{sub 2}Te{sub 3} and for PbTe, and the results of recent experiments are discussed.

  4. Transport of reservoir fines

    DEFF Research Database (Denmark)

    Yuan, Hao; Shapiro, Alexander; Stenby, Erling Halfdan

    Modeling transport of reservoir fines is of great importance for evaluating the damage of production wells and infectivity decline. The conventional methodology accounts for neither the formation heterogeneity around the wells nor the reservoir fines’ heterogeneity. We have developed an integral...... dispersion equation in modeling the transport and the deposition of reservoir fines. It successfully predicts the unsymmetrical concentration profiles and the hyperexponential deposition in experiments....

  5. Climate change : transportation table

    International Nuclear Information System (INIS)

    Ogilvie, K.

    1999-01-01

    The Kyoto Protocol sets greenhouse gas (GHG) reduction targets for the post-2000 period. If ratified, Canada will be committed to reduce emissions of GHGs by 6 per cent below 1990 levels during the period 2008-2012. A recommended national strategy is to establish 'issue tables' that will advise the Ministers of Energy and Environment on preferred options to reach the Kyoto target and to identify early actions that can be taken. The 'Transportation Table' which is the focus of this paper, is one of the 15 sectoral tables. The Transportation Table will identify by July 1999, specific measures to mitigate GHG emissions from Canada's transportation sector. Currently, GHG emissions from the transportation sector are predicted to be 27 per cent above 1990 levels by 2010. Fuel taxes, emissions trading, and research into improved vehicle technologies and automotive fuels are some of the recommended options which can help reduce emissions trading from the transportation sector. Studies are underway to deal with emissions from transport in two sub-groups, freight and passenger. 1 fig

  6. Experimental constraints on transport

    International Nuclear Information System (INIS)

    Luce, T.C.; Petty, K.H.; Burrell, K.H.; Forest, C.B.; Gohil, P.; Groebner, R.J.; De Haas, J.C.M.; James, R.A.; Makowski, M.A.

    1994-12-01

    Characterization of the cross-field energy transport in magnetic confinement experiments in a manner applicable to the accurate assessment of future machine performance continues to be a challenging goal. Experimental results from the DIII-D tokamak in the areas of dimensionless scaling and non-diffusive transport represent progress toward this goal. Dimensionless scaling shows how beneficial the increase in machine size and magnetic field is for future devices. The experiments on DIII-D are the first to determine separately the electron and ion scaling with normalized gyroradius ρ * ; the electrons scale as expected from gyro-Bohm class theories, while the ions scale consistent with the Goldston empirical scaling. This result predicts an increase in transport relative to Bohm diffusion as ρ * decreases in future devices. The existence of distinct ρ * scalings for ions and electrons cautions against a physical interpretation of one-fluid or global analysis. The second class of experiments reported here are the first to demonstrate the existence of non-diffusive energy transport. Electron cyclotron heating was applied at the half radius; the electron temperature profile remains substantially peaked. Power balance analysis indicates that heat must flow in the direction of increasing temperature, which is inconsistent with purely diffusive transport. The dynamics of electron temperature perturbations indicate the presence in the heat flux of a term dependent on temperature rather than its gradient. These two observations strongly constrain the types of models which can be applied to cross-field heat transport

  7. Transportation of nuclear materials

    International Nuclear Information System (INIS)

    Brobst, W.A.

    1977-01-01

    Twenty years of almost accident-free transport of nuclear materials is pointed to as evidence of a fundamentally correct approach to the problems involved. The increased volume and new technical problems in the future will require extension of these good practices in both regulations and packaging. The general principles of safety in the transport of radioactive materials are discussed first, followed by the transport of spent fuel and of radioactive waste. The security and physical protection of nuclear shipments is then treated. In discussing future problems, the question of public understanding and acceptance is taken first, thereafter transport safeguards and the technical bases for the safety regulations. There is also said to be a need for a new technology for spent fuel casks, while a re-examination of the IAEA transport standards for radiation doses is recommended. The IAEA regulations regarding quality assurance are said to be incomplete, and more information is required on correlations between engineering analysis, scale model testing and full scale crash testing. Transport stresses on contents need to be considered while administrative controls have been neglected. (JIW)

  8. Transport processes in plasmas

    International Nuclear Information System (INIS)

    Balescu, R.

    1988-01-01

    This part is devoted to the classical transport theory in plasmas. Ch. 1 is a chapter of 'pure' hamiltonian mechanics and starts with the study of the motion of an individual charged particle in the presence of an electromagnetic field. Ch. 2 introduces the tools of statistical mechanics for the study of large collections of charged particles. A kinetic theory is derived as a basic tool for transport theory. In ch. 3 the hydro-dynamic - or plasmadynamic - balance equations are derived. The macroscopic dynamical equations have the structure of an infinite hierarchy. This introduces the necessity of construction of a transport theory, by which te infinite set of equations can be reduced to a finite, closed set. This can only be done by a detailed analysis of the kinetic equation under well defined conditions. The tools for such nan analysis are developed in ch. 4. In ch. 5 the transport equations, relating the unknown fluxes of matter, momentum, energy and electricity to the hydrodynamic variables, are derived and discussed. In ch. 6 the results are incorporated into the wider framework of non-equilibrium thermodynamics by connecting the transport processes to the central concept of entropy production. In ch. 7 the results of transport theory are put back into the equations of plasmadynamics

  9. Transport of radioisotopes

    International Nuclear Information System (INIS)

    Aoki, Shigefumi

    1978-01-01

    Presently the amount of radioisotopes increased very much and the application spread to wide fields in Japan. Since facilities using radioisotopes are distributed to every place in the country, every transport means such as airplanes, automobiles, railways, ships and mail are employed. The problems in the transport of radioisotopes include too much difference in the recognition of criticality among the persons concerning the transportation and treatment, knowledges of shielding and energy difference in the types of radiation and handling of sealed and unsealed sources and the casks for transport. IAEA established the latest regulation on the package of radioisotopes in 1973, and in Japan, the related regulations will be revised according to the IAEA's regulation in near future. The present status in the inspection at the time of shipment, supervision, and the measures to the accidents are described for the transport means of airplanes, ships and automobiles. Finally, concerning the insurance for cargo, the objects of the insurance for radioisotopes include either the radioisotopes contained in casks for transportation or radioisotopes only. Generally, radioisotopes are accepted in all-risk condition including casks and limited to the useful radioisotopes for peaceful use. (Wakatsuki, Y

  10. Paleoclassical transport explains electron transport barriers in RTP and TEXTOR

    NARCIS (Netherlands)

    Hogeweij, G. M. D.; Callen, J.D.

    2008-01-01

    The recently developed paleoclassical transport model sets the minimum level of electron thermal transport in a tokamak. This transport level has proven to be in good agreement with experimental observations in many cases when fluctuation-induced anomalous transport is small, i.e. in (near-) ohmic

  11. ANALYISIS OF TRANSPORTATION SYSTEMS AND TRANSPORTATION POLICIES IN TURKEY

    Directory of Open Access Journals (Sweden)

    Ali Payıdar AKGÜNGÖR

    2004-03-01

    Full Text Available Transportation systems have to be considered and analysed as a whole while transportation demand, becoming as a natural outcome of socioeconomic and socio-cultural structure, is being evaluated. It is desired that transportation system, which will be selected for both passenger and freight transport, should be rapid, economic, safe, causing least harm to environment and appropriate for the conditions of a country. However, it is difficult for a transportation system to have all these properties. Every transportation system has advantages and disadvantages over each other. Therefore, comprehensive plans for future periods have to be prepared and how the sources of the country should be reasonably distributed among transportation systems must be investigated. Also, transportation plans have to be prepared to get coordinated operations among transportation systems while great investments are instituted in the entire country. There is no doubt that it is possible with combined transportation instead of concentration on one transportation system. Transportation policies in Turkey should be questioned since the level of highway transportation usage reaches to 95 % and level of sea transportation usage drops to less than 1 % in spite of being surrounded with sea in three sides of our land. In this paper, transportation systems and transportation policies in Turkey are evaluated in general and problems are analysed. Proposals are presented for the solutions of these problems.

  12. Spent fuel transportation problems

    International Nuclear Information System (INIS)

    Kondrat'ev, A.N.; Kosarev, Yu.A.; Yulikov, E.A.

    1977-01-01

    In this paper, problems of transportation of nuclear spent fuel to reprocessing plants are discussed. The solutions proposed are directed toward the achievement of the transportation as economic and safe as possible. The increase of the nuclear power plants number in the USSR and the great distances between these plants and the reprocessing plants involve an intensification of the spent fuel transportation. Higher burnup and holdup time reduction cause the necessity of more bulky casks. In this connection, the economic problems become still more important. One of the ways of the problem solution is the development of rational and cheap cask designs. Also, the enforcement in the world of the environmental and personnel health protection requires to increase the transportation reliability and safety. The paper summarizes safe transportation rules with clarifying the following questions: the increase of the transport unit quantity of the spent fuel; rational shipment organization that minimizes vehicle turnover cycle duration; development of the reliable calculation methods to determine strength, thermal conditions and nuclear safety of transport packaging as applied to the vehicles of high capacity; maximum unification of vehicles, calculation methods and documents; and cask testing on models and in pilot scale on specific test rigs to assure that they meet the international safe fuel shipment rules. Besides, some considerations on the choice and use of structural materials for casks are given, and problems of manufacturing such casks from uranium and lead are considered, as well as problems of the development of fireproof shells, control instrumentation, vehicles decontamination, etc. All the problems are considered from the point of view of normal and accidental shipment conditions. Conclusions are presented [ru

  13. Intelligent Transport Systems in the Management of Road Transportation

    Science.gov (United States)

    Kalupová, Blanka; Hlavoň, Ivan

    2016-11-01

    Extension of European Union causes increase of free transfer of people and goods. At the same time they raised the problems associated with the transport, e.g. congestion and related accidents on roads, air traffic delays and more. To increase the efficiency and safety of transport, the European Commission supports the introduction of intelligent transport systems and services in all transport sectors. Implementation of intelligent transport systems and services in the road transport reduces accident frequency, increases the capacity of existing infrastructure and reduces congestions. Use of toll systems provides resources needed for the construction and operation of a new road network, improves public transport, cycling transport and walking transport, and also their multimodal integration with individual car transport.

  14. Radioactive material transporting container

    International Nuclear Information System (INIS)

    Watabe, Yukio.

    1990-01-01

    As a supporting member of a sealing container for containing spent fuels, etc., a straight pipe or a cylinder has been used. However, upon dropping test, the supporting member is buckled toward the central axis of a transporting container and a shock absorber is crushed in the axial direction to prevent its pushing force to the outer side, which may possibly hinder normal shock moderating function. Then, at least more than one-half of the supporting member is protruded radially to the outer side of the sealing container beyond the fixed portion with the sealed container, so that the member has a portion extended in the radial outside of the transporting container with an angle greater than the angle formed between a line connecting the outer circumference at the bottom of an outer cylinder with the gravitational center of the transporting container and the central axis of the transporting container. As a result, buckling of the supporting member toward the central axis of the transporting container upon dropping test can be prevented and the deformation of the shock absorber is neither not prevented to exhibit normal shock absorbing effect. This can improve the reliability and reduce the amount of shock absorbers. (N.H.)

  15. Sustainable Urban Transport Planning

    Directory of Open Access Journals (Sweden)

    Boitor Melania R.

    2013-07-01

    Full Text Available Environmental protection has become a common issue in every area, but extremely important for the domains which deal with intensive energy consumption as it is the case of the transportation. Achieving the sustainable cities on the other hand, is also focused on the protection of the environment in order to provide a higher quality of life for the population. Therefore it is considered that by improving the urban transportation planning additional benefits could be provided for both the environment and the sustainable development of the cities. One possibility is to supplement the traditionally land-use plans with the transportrelated zones analysis, where the city is divided in public transport, pedestrian and caroriented zones. Analyzing the transport-related zones of a city is important as it provides additional information in the assessment of the development trend. The process of zoning was conducted for the city of Cluj-Napoca, Romania. In this paper, the outcome of the zoning was analyzed for a more comprehensive review of the urban transport in order to attain a sustainable-oriented approach of the urban area development.

  16. A new transport hub

    CERN Multimedia

    Corinne Pralavorio

    2016-01-01

    CERN’s new Mobility Centre, allowing you to switch easily from one mode of transport to another, has just been officially opened.   Inauguration of the CERN Mobility Centre by Martin Steinacher, Director for Finance and Human Resources, and Lluis Miralles, Head of the SMB department. CERN’s new Mobility Centre, on the car park next to the Globe of Science and Innovation was officially opened on Tuesday, 22 March. The centre brings together all of CERN’s transport options in a single location. "Our aim is to create an intermodal hub where CERN users and personnel can switch from one mode of transport to another, and from CERN transport to public transport," explains Lluis Miralles, head of the Site Management and Buildings (SMB) department. The Mobility Centre incorporates the CERN bike and car rental services, the self-service car- and bike-sharing schemes, and SIXT car rental facilities (for long-distance journeys). It is located right ne...

  17. Nuclear materials transport worldwide

    International Nuclear Information System (INIS)

    Stellpflug, J.

    1987-01-01

    This Greenpeace report shows: nuclear materials transport is an extremely hazardous business. There is no safe protection against accidents, kidnapping, or sabotage. Any moment of a day, at any place, a nuclear transport accident may bring the world to disaster, releasing plutonium or radioactive fission products to the environment. Such an event is not less probable than the MCA at Chernobyl. The author of the book in hand follows the secret track of radioactive materials around the world, from uranium mines to the nuclear power plants, from reprocessing facilities to the waste repositories. He explores the routes of transport and the risks involved, he gives the names of transport firms and discloses incidents and carelessness, tells about damaged waste drums and plutonium that 'disappeared'. He also tells about worldwide, organised resistance to such nuclear transports, explaining the Greenpeace missions on the open sea, or the 'day X' operation at the Gorleben site, informing the reader about protests and actions for a world freed from the threat of nuclear energy. (orig./HP) [de

  18. Hydrogen and transport

    International Nuclear Information System (INIS)

    Tomsons, E.

    2007-01-01

    In 2005 the Latvian transport consumed 43 PJ, which makes up 23% of the total priMary resources used in the country. On the world scale this latter figure was 17.6% in 2003. On the 1st October of 2005 in Latvia 808.6 thous. of cars, 119.9 thous. of lorries, 10,7 thous. of buses and 27.1 thous. of motorcycles were registred. The annual growth in the number of light motor cars in the last years was 5.5% on the average. In 2005 the Latvian transport consumed 335 thous. tons of petrol and 542 thous. tons of diesel fuel, which makes up 87.4% of the total resources used (in terms of the combustion heat). In the period of 2002-2005 the annual growth of energy resources consumed by transport was 4.87% on the average. According to forecasts, in 2015 the transports of our country will spend 1.64 times more energy resources as compared with 2005. If the transport of 2015 uses hydrogen, then for Latvia 270 thous. tons of this product will be needed. To obtain 270 thous. tons of hydrogen from water using the up-to-date equipment for electrolysis a considerable amount of electric energy is required. Such amount can be produced by generating stations of the total capacity of 1680 MWe(net). This figure is close to that for the total installed capacity of electric energy production already existing in Latvia. (Author)

  19. Transportation and air quality

    International Nuclear Information System (INIS)

    Roseland, M.

    1992-01-01

    In the greater Vancouver regional district (GVRD), some 80% of the annual production of 600,000 tonnes of air pollutants come from motor vehicles. Three critical air quality issues in the GVRD are discussed: local air pollution, ozone layer depletion, and greenhouse gas emissions, all of which are fundamentally linked to transportation. Overall air quality in the GVRD has been judged acceptable by current federal standards, but ground-level ozone has exceeded maximum tolerable levels at some locations and concentrations of suspended particulates are above maximum acceptable levels. Serious deterioration in air quality has been predicted unless a concerted effort is made to manage air quality on an airshed-wide basis. The GVRD is developing Canada's first Air Management Plan with the goal of halving atmospheric emissions by 2000. GVRD transportation priorities stress public transit, walking, cycling, car pooling, and reducing of travel demand; however, the viability of such strategies depends on decisions made outside the transportation sector. Restricted authority and jurisdiction also hinder GVRD goals; the regional level of government has no authority over highways or transit and only has authority for pollution control in some parts of the Fraser Valley. Airshed quality management, using the Los Angeles example, is seen as a possible direction for future GVRD policymaking in the transportation sector. A single regional planning agency with responsibility for transportation, land use, and air quality management appears as the best option for an integrated approach to solve multiple problems. 19 refs

  20. Transport in Stochastic Media

    International Nuclear Information System (INIS)

    Haran, O.; Shvarts, D.; Thieberger, R.

    1998-01-01

    Classical transport of neutral particles in a binary, scattering, stochastic media is discussed. It is assumed that the cross-sections of the constituent materials and their volume fractions are known. The inner structure of the media is stochastic, but there exist a statistical knowledge about the lump sizes, shapes and arrangement. The transmission through the composite media depends on the specific heterogeneous realization of the media. The current research focuses on the averaged transmission through an ensemble of realizations, frm which an effective cross-section for the media can be derived. The problem of one dimensional transport in stochastic media has been studied extensively [1]. In the one dimensional description of the problem, particles are transported along a line populated with alternating material segments of random lengths. The current work discusses transport in two-dimensional stochastic media. The phenomenon that is unique to the multi-dimensional description of the problem is obstacle bypassing. Obstacle bypassing tends to reduce the opacity of the media, thereby reducing its effective cross-section. The importance of this phenomenon depends on the manner in which the obstacles are arranged in the media. Results of transport simulations in multi-dimensional stochastic media are presented. Effective cross-sections derived from the simulations are compared against those obtained for the one-dimensional problem, and against those obtained from effective multi-dimensional models, which are partially based on a Markovian assumption

  1. Thermal Transport in Phosphorene.

    Science.gov (United States)

    Qin, Guangzhao; Hu, Ming

    2018-03-01

    Phosphorene, a novel elemental 2D semiconductor, possesses fascinating chemical and physical properties which are distinctively different from other 2D materials. The rapidly growing applications of phosphorene in nano/optoelectronics and thermoelectrics call for comprehensive studies of thermal transport properties. In this Review, based on the theoretical and experimental progresses, the thermal transport properties of single-layer phosphorene, multilayer phosphorene (nanofilms), and bulk black phosphorus are summarized to give a general view of the overall thermal conductivity trend from single-layer to bulk form. The mechanism underlying the discrepancy in the reported thermal conductivity of phosphorene is discussed by reviewing the effect of different functionals and cutoff distances on the thermal transport evaluations. This Review then provides fundamental insight into the thermal transport in phosphorene by reviewing the role of resonant bonding in driving giant phonon anharmonicity and long-range interactions. In addition, the extrinsic thermal conductivity of phosphorene is reviewed by discussing the effects of strain and substrate, together with phosphorene based heterostructures and nanoribbons. This Review summarizes the progress of thermal transport in phosphorene from both theoretical calculations and experimental measurements, which would be of significance to the design and development of efficient phosphorene based nanoelectronics. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. ANALYISIS OF TRANSPORTATION SYSTEMS AND TRANSPORTATION POLICIES IN TURKEY

    OpenAIRE

    Ali Payıdar AKGÜNGÖR; Abdulmuttalip DEMİREL

    2004-01-01

    Transportation systems have to be considered and analysed as a whole while transportation demand, becoming as a natural outcome of socioeconomic and socio-cultural structure, is being evaluated. It is desired that transportation system, which will be selected for both passenger and freight transport, should be rapid, economic, safe, causing least harm to environment and appropriate for the conditions of a country. However, it is difficult for a transportation system to have all these properti...

  3. Transport regulation for radioactive materials

    International Nuclear Information System (INIS)

    Ha Vinh Phuong.

    1986-01-01

    Taking into account the specific dangers associated with the transport of radioactive materials (contamination, irradiation, heat, criticality), IAEA regulations concerning technical specifications and administrative procedures to ward off these dangers are presented. The international agreements related to the land transport, maritime transport and air transport of radioactive materials are also briefly reviewed

  4. Transport Research Needs

    DEFF Research Database (Denmark)

    Ortúzar, Juan de Dios; Cherchi, Elisabetta; Rizzi, Luis

    2014-01-01

    Transport is a large, multidisciplinary and fascinating field, encompassing vastly different areas of research. In fact transport interests span from not very well understood (in fieldwork) issues related with survey methods to highly complex questions associated with the dynamic equilibration...... of supply and demand in strategic planning contexts; the latter involving large zoning systems, huge multimodal networks and highly complex dynamic modelling approaches (Mahmassani, 2001). But questions also arise at a more macro level (and in a different time span) regarding the interaction of transport....... For these reasons, in this chapter we will just concentrate on issues related with modelling the demand for travel in the relatively short term. In particular, we will refer to modelling discrete short-term choices, such as mode, route and/or trip timing; although in our analysis we will pay attention to research...

  5. Transportation Institutional Plan

    Energy Technology Data Exchange (ETDEWEB)

    1986-08-01

    This Institutional Plan is divided into three chapters. Chapter 1 provides background information, discusses the purposes of the Plan and the policy guidance for establishing the transportation system, and describes the projected system and the plans for its integrated development. Chapter 2 discusses the major participants who must interact to build the system. Chapter 3 suggests mechanisms for interaction that will foster wide participation in program planning and implementation and provides a framework for managing and resolving the issues related to development and operation of the transportation system. A list of acronyms and a glossary are included for the reader's convenience. Also included in this Plan are four appendices. Of particular importance is Appendix A, which includes detailed discussion of specific transportation issues. Appendices B, C, and D provide supporting material to assist the reader in understanding the roles of the involved institutions.

  6. Large orbit neoclassical transport

    International Nuclear Information System (INIS)

    Lin, Z.; Tang, W.M.; Lee, W.W.

    1997-01-01

    Neoclassical transport in the presence of large ion orbits is investigated. The study is motivated by the recent experimental results that ion thermal transport levels in enhanced confinement tokamak plasmas fall below the open-quotes irreducible minimum levelclose quotes predicted by standard neoclassical theory. This apparent contradiction is resolved in the present analysis by relaxing the basic neoclassical assumption that the ions orbital excursions are much smaller than the local toroidal minor radius and the equilibrium scale lengths of the system. Analytical and simulation results are in agreement with trends from experiments. The development of a general formalism for neoclassical transport theory with finite orbit width is also discussed. copyright 1997 American Institute of Physics

  7. Transportable criticality alarm system

    International Nuclear Information System (INIS)

    Clem, W.E.

    1988-09-01

    The Transportable Criticality Alarm System was developed at the Hanford Site in 1982 to comply with the requirements of US Department of Energy Order DOE 5480.1, 12/18/80, and ANSI/ANS-8.3- 1979. The portable unit that it replaced failed to comply with the new requirements in that it did not provide the necessary warning of malfunctions, nor did it provide the Hanford Site standard criticality alarm signal. Modern technology allowed the Transportable Criticality Alarm System to comply with the criticality requirements cited and to incorporate other features that make it more usable, maintainable, and reliable. The Transportable Criticality Alarm System (TCAS) provides temporary criticality coverage in manned areas where the facility criticality alarm system is not operable. This gamma radiation-sensitive system has been in use for the past 6 yr at the Hanford Site. 2 refs., 4 figs., 1 tab

  8. Electrical railway transportation systems

    CERN Document Server

    Brenna, Morris; Zaninelli, Dario

    2018-01-01

    Allows the reader to deepen their understanding of various technologies for both fixed power supply installations of railway systems and for railway rolling stock. This book explores the electric railway systems that play a crucial role in the mitigation of congestion and pollution caused by road traffic. It is divided into two parts: the first covering fixed power supply systems, and the second concerning the systems for railway rolling stock. In particular, after a historical introduction to the framework of technological solutions in current use, the authors investigate electrification systems for the power supply of rail vehicles, trams, and subways. Electrical Railway Transportation Systems explores the direct current systems used throughout the world for urban and suburban transport, which are also used in various countries for regional transport. It provides a study of alternating current systems, whether for power supply frequency or for special railway frequency, that are used around the world for ...

  9. Economical motor transport operations

    Energy Technology Data Exchange (ETDEWEB)

    Cooke, P

    1979-09-01

    Motor transport is one area in a company where energy conservation is a function primarily of operative education and motivation rather than mechanical or technical control and monitoring. Unless the driver wants to save energy by proper operation of the vehicle, there is nothing the company can do to force him, whatever equipment it fits to the vehicles, or incentives it offers. This article gives an overview of the use of energy in road transport and examines a number of actions that can be taken to conserve energy. It discusses the question of the cost-effectiveness of transport energy conservation in the light of the complex issues involved. The problems and opportunities of implementing energy-saving programs are examined. (MCW)

  10. Fuel element transport container

    International Nuclear Information System (INIS)

    Benna, P.; Neuenfeldt, W.

    1979-01-01

    The reprocessing system includes a large number of waterfilled ponds next to each other for the intermediate storage of fuel elements from LWR's. The fuel element transport device is allocated to a middle pond. The individual ponds are separated from each other by walls, and are only accessible from the middle pond via narrow passages. The transport device includes a telescopic running rail for a trolley with a grab device for the fuel element. The running rail is supported in turn by a second trolley, which can be moved by wheels on rails. Part of the drive of the first trolley is arranged on the second one. Using this transport device, adjacent ponds can be served through the passage openings. (DG) [de

  11. Preface: Nonclassical Transport

    International Nuclear Information System (INIS)

    Bolshov, L.; Kondratenko, P.; Pruess, K.

    2008-01-01

    Transport phenomena in highly heterogeneous media can be dramatically different from those in homogeneous media and therefore are of great fundamental and practical interest. Anomalous transport occurs in semiconductor physics, plasma physics, astrophysics, biology, and other areas. It plays an especially important role in hydrogeology because it may govern the rate of migration and degree of dispersion of groundwater contaminants from hazardous waste sites. The series of four articles in this special section of Vadose Zone Journal is devoted to transport phenomena in heterogeneous media in the context of geologic disposal of radioactive waste. It contains the results of joint investigations performed at the Nuclear Safety Institute of the Russian Academy of Sciences and Lawrence Berkeley National Laboratory in California. The work was supported by the U.S. DOE (under Contract No. DEAC02-05CH11231). The problems addressed in this research involve a broad range of space and time scales and were approached using modern methods of theoretical and computational physics, such as scaling analysis and diagrammatic techniques used before in critical phenomena theory. Special attention is paid to the asymptotics of concentration behavior (concentration tails). This issue is exceptionally important for the reliability assessments of radioactive waste disposal because, depending on the structure of the tails, concentrations at large distances from the source can differ by many orders of magnitude. In the first paper of this special section, Bolshov et al. (2008b) present an overview of field and laboratory observations that demonstrate nonclassical flow and transport behavior in geologic media. It is recognized that natural fracture networks as a rule have fractal geometry and can be classified as percolation systems. This is one of the main factors giving rise to anomalous transport in geologic media. Another important factor is the presence of contaminant traps provided by

  12. Prioritized Contact Transport Stream

    Science.gov (United States)

    Hunt, Walter Lee, Jr. (Inventor)

    2015-01-01

    A detection process, contact recognition process, classification process, and identification process are applied to raw sensor data to produce an identified contact record set containing one or more identified contact records. A prioritization process is applied to the identified contact record set to assign a contact priority to each contact record in the identified contact record set. Data are removed from the contact records in the identified contact record set based on the contact priorities assigned to those contact records. A first contact stream is produced from the resulting contact records. The first contact stream is streamed in a contact transport stream. The contact transport stream may include and stream additional contact streams. The contact transport stream may be varied dynamically over time based on parameters such as available bandwidth, contact priority, presence/absence of contacts, system state, and configuration parameters.

  13. Air transport system

    CERN Document Server

    Schmitt, Dieter

    2016-01-01

    The book addresses all major aspects to be considered for the design and operation of aircrafts within the entire transportation chain. It provides the basic information about the legal environment, which defines the basic requirements for aircraft design and aircraft operation. The interactions between  airport, air traffic management and the airlines are described. The market forecast methods and the aircraft development process are explained to understand the very complex and risky business of an aircraft manufacturer. The principles of flight physics as basis for aircraft design are presented and linked to the operational and legal aspects of air transport including all environmental impacts. The book is written for graduate students as well as for engineers and experts, who are working in aerospace industry, at airports or in the domain of transport and logistics.

  14. Transportable hyperpolarized metabolites

    Science.gov (United States)

    Ji, Xiao; Bornet, Aurélien; Vuichoud, Basile; Milani, Jonas; Gajan, David; Rossini, Aaron J.; Emsley, Lyndon; Bodenhausen, Geoffrey; Jannin, Sami

    2017-01-01

    Nuclear spin hyperpolarization of 13C-labelled metabolites by dissolution dynamic nuclear polarization can enhance the NMR signals of metabolites by several orders of magnitude, which has enabled in vivo metabolic imaging by MRI. However, because of the short lifetime of the hyperpolarized magnetization (typically <1 min), the polarization process must be carried out close to the point of use. Here we introduce a concept that markedly extends hyperpolarization lifetimes and enables the transportation of hyperpolarized metabolites. The hyperpolarized sample can thus be removed from the polarizer and stored or transported for use at remote MRI or NMR sites. We show that hyperpolarization in alanine and glycine survives 16 h storage and transport, maintaining overall polarization enhancements of up to three orders of magnitude. PMID:28072398

  15. LNG in transportation

    International Nuclear Information System (INIS)

    Madden, Mike; White, Nick; Le Fevre, Chris

    2014-01-01

    This document summarizes the content of a 402 p. study published by CEDIGAZ, the International Center for Natural Gas Information. According to this study, LNG as a fuel will capture a significant market share in the transport sector by 2035. The greatest potential is seen in road transport, were annual demand is projected to reach 96 million tons per year (mtpa) in CEDIGAZ' base scenario while demand in the marine sector could grow to an estimated 77 mtpa. The rail sector could add another 6 mtpa to global demand. However, the development of LNG as a transport fuel faces a number of challenges, and will have to go hand in hand with the development of fueling infrastructure

  16. Paleoclassical electron heat transport

    International Nuclear Information System (INIS)

    Callen, J.D.

    2005-01-01

    Radial electron heat transport in low collisionality, magnetically-confined toroidal plasmas is shown to result from paleoclassical Coulomb collision processes (parallel electron heat conduction and magnetic field diffusion). In such plasmas the electron temperature equilibrates along magnetic field lines a long length L, which is the minimum of the electron collision length and a maximum effective half length of helical field lines. Thus, the diffusing field lines induce a radial electron heat diffusivity M ≅ L/(πR 0q ) ∼ 10 >> 1 times the magnetic field diffusivity η/μ 0 ≅ ν e (c/ω p ) 2 . The paleoclassical electron heat flux model provides interpretations for many features of 'anomalous' electron heat transport: magnitude and radial profile of electron heat diffusivity (in tokamaks, STs, and RFPs), Alcator scaling in high density plasmas, transport barriers around low order rational surfaces and near a separatrix, and a natural heat pinch (or minimum temperature gradient) heat flux form. (author)

  17. Bæredygtig transport

    DEFF Research Database (Denmark)

    Haas, Henning de; Søndergaard, Mads

    2009-01-01

    I denne artikel sættes fokus på bæredygtighed og transport. Baggrunden for artiklen er en undersøgelse af status for bæredygtig transport i et antal danske virksomheder i samarbejde med DHL. Indledningen giver en baggrund for fokus på bæredygtighed, efterfølgende sættes der fokus på "Green SCM......" for at afklare hvad det indeholder, definitioner mv. Dette er udgangspunktet for en præsentation af resultaterne fra undersøgelsen af bæredygtig transport. Undersøgelsen opsummeres og leder frem til en række implikationer for henholdsvis kunder (transportkøberne) og transportleverandørerne....

  18. TRANSPORTATION INDUSTRY EFFECTIVE MANAGEMENT CONDITIONS

    Directory of Open Access Journals (Sweden)

    V. I. Kuznetsov

    2011-01-01

    Full Text Available Main aspects that determine conditions of transportation industry effective management and decrease of transportation expenses are discussed. Theoretical concepts making it possible to solve the problem of scientific management of the whole country’s goods transportation costs are provided for. Main approaches are presented to the solution of motor transport operation ecological optimization problem as well as to the rise of motor transport workers’ labor productivity, to the increase of transportation vehicles use efficiency and to determine functional capacity of the motor transport complex.

  19. Onsite transportation hazards assessment

    International Nuclear Information System (INIS)

    Burnside, M.E.

    1998-01-01

    This report documents the emergency preparedness Hazards Assessment for the onsite transportation of hazardous material at the Hanford Site. The assessment is required by US Department of Energy (DOE) Order 5500.3A and provides the technical basis for the emergency classification and response procedures. A distinction is made between onsite for the purpose of emergency preparedness and onsite for the purpose of applying US Department of Transportation (DOT) regulations. Onsite for the purpose of emergency preparedness is considered to be within the physical boundary of the entire Hanford Site. Onsite for the purpose of applying DOT regulations is north of the Wye Barricade

  20. Transport of radioactive materials

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1960-04-15

    The increasing use of radioactive substances, not only in reactor operations but also in medicine, industry and other fields, is making the movement of these materials progressively wider, more frequent and larger in volume. Although regulations for the safe transport of radioactive materials have been in existence for many years, it has now become necessary to modify or supplement the existing provisions on an international basis. It is essential that the regulations should be applied uniformly by all countries. It is also desirable that the basic regulations should be uniform for all modes of transport so as to simplify the procedures to be complied with by shippers and carriers

  1. The Trojan. [supersonic transport

    Science.gov (United States)

    1992-01-01

    The Trojan is the culmination of thousands of engineering person-hours by the Cones of Silence Design Team. The goal was to design an economically and technologically viable supersonic transport. The Trojan is the embodiment of the latest engineering tools and technology necessary for such an advanced aircraft. The efficient design of the Trojan allows for supersonic cruise of Mach 2.0 for 5,200 nautical miles, carrying 250 passengers. The per aircraft price is placed at $200 million, making the Trojan a very realistic solution for tomorrows transportation needs. The following is a detailed study of the driving factors that determined the Trojan's super design.

  2. Constrained Optimal Transport

    Science.gov (United States)

    Ekren, Ibrahim; Soner, H. Mete

    2018-03-01

    The classical duality theory of Kantorovich (C R (Doklady) Acad Sci URSS (NS) 37:199-201, 1942) and Kellerer (Z Wahrsch Verw Gebiete 67(4):399-432, 1984) for classical optimal transport is generalized to an abstract framework and a characterization of the dual elements is provided. This abstract generalization is set in a Banach lattice X with an order unit. The problem is given as the supremum over a convex subset of the positive unit sphere of the topological dual of X and the dual problem is defined on the bi-dual of X. These results are then applied to several extensions of the classical optimal transport.

  3. Transportation of nuclear fuel

    International Nuclear Information System (INIS)

    Prowse, D.R.

    1979-01-01

    Shipment of used fuel from nuclear reactors to a central fuel management facility is discussed with particular emphasis on the assessment of the risk to the public due to these shipments. The methods of transporting used fuel in large shipping containers is reviewed. In terms of an accident scenario, it is demonstrated that the primary risk of transport of used fuel is due to injury and death in common road accidents. The radiological nature of the used fuel cargo is, for all practical purposes, an insignificant factor in the total risk to the public. (author)

  4. Transporte de equinos

    OpenAIRE

    Marrero, Diego

    2012-01-01

    El transporte de caballos es una actividad muy frecuente que se realiza por distintos motivos: competencias de equitación, cría, subastas, tratamientos, etc. En todos los casos, una de las principales preocupaciones de los propietarios es procurar un traslado seguro y confortable. Esto sucede porque si el medio de transporte no es el adecuado puede provocar en los equinos un importante distrés, que se manifiesta en patologías de origen respiratorio, así como traumatismos en los miembros, lo q...

  5. Transportation of hazardous goods

    CERN Multimedia

    TS Department

    2008-01-01

    A general reminder: any transportation of hazardous goods by road is subject to the European ADR rules. The goods concerned are essentially the following: Explosive substances and objects; Gases (including aerosols and non-flammable gases such as helium and nitrogen); Flammable substances and liquids (inks, paints, resins, petroleum products, alcohols, acetone, thinners); Toxic substances (acids, thinners); Radioactive substances; Corrosive substances (paints, acids, caustic products, disinfectants, electrical batteries). Any requests for the transport of hazardous goods must be executed in compliance with the instructions given at this URL: http://ts-dep.web.cern.ch/ts-dep/groups/he/HH/adr.pdf Heavy Handling Section TS-HE-HH 73793 - 160364

  6. TRANSPORT OF COUNTERFEIT GOODS

    Directory of Open Access Journals (Sweden)

    Dagmar Babčanová

    2014-09-01

    Full Text Available The paper is focused on a current problem of transport of counterfeit goods in the European Union. Counterfeiting has a strong influence on the distribution organizations worldwide because most of counterfeit goods threaten the health and safety of consumers. Counterfeiting is a serious problem in the world economy today. The purpose of this paper is to point out the danger of counterfeiting in connection with the transport of Intellectual Property (IP rights - infringing goods. Background of the paper’s content is based on secondary data research of publicly available sources - international statistics and world reports.

  7. Transcellular transport of calcium

    Energy Technology Data Exchange (ETDEWEB)

    Terepka, A R; Coleman, J R; Armbrecht, H J; Gunter, T E

    1976-01-01

    Studies of two calcium transporting epithelia, embryonic chick chorioallantoic membrane and the small intestine of rat and chick, have strongly suggested that the transfer of calcium across a cell involves processes distinctly different from intracellular calcium ion regulation. In the proposed model, transcellular calcium transport is considered as a specialized process developed only by certain cells in those tissues charged with bulk transfer of calcium. The overall effect of the endocytotic mechanism is bulk calcium movement across a cell, protection of mitochondria from exposure to high concentrations of calcium, and the avoidance of wide and potentially toxic fluctuations in cytosol ionic calcium levels. (MFB)

  8. PIPELINE TRANSPORTATION PLANNERS

    OpenAIRE

    FREDERICO DOS SANTOS LIPORACE

    2005-01-01

    Oleodutos têm um papel importante no transporte de petróleo e de seus derivados, pois são a maneira mais eficaz de transportar grandes volumes por longas distâncias. A motivação deste trabalho é que uma parte não negligenciável do preço final de um derivado de petróleo é influenciada pelo custo de transporte. Apesar disso, até onde sabemos, apenas alguns autores trabalharam neste problema específico, a maioria utilizando técnicas de programação inteira. Este tr...

  9. Transport of nuclear materials

    International Nuclear Information System (INIS)

    Anon.

    2002-01-01

    During november and december 2001, 2 events concerning nuclear transport were reported and classified on the first grade (grade 1) of the INES scale. The first event concerns a hole in a transport cask of contaminated tools. The hole seems to have been made by the fork of a handling equipment. The second event concerns the loss of a parcel containing a technetium generator, this generator represented an activity of about 141 G Becquerel of 99 Mo the day it left the premises of CIS-bio in Saclay. (A.C.)

  10. Introduction to radiation transport

    International Nuclear Information System (INIS)

    Olson, G.L.

    1998-01-01

    This lecture will present time-dependent radiation transport where the radiation is coupled to a static medium, i.e., the material is not in motion. In reality, radiation exerts a pressure on the materials it propagates through and will accelerate the material in the direction of the radiation flow. This fully coupled problem with radiation transport and materials in motion is referred to as radiation-hydrodynamics (or in a shorthand notation: rad-hydro) and is beyond the scope of this lecture

  11. Energy for Transport

    DEFF Research Database (Denmark)

    Figueroa, Maria; Lah, Oliver; Fulton, Lewis M.

    2014-01-01

    Global transportation energy use is steeply rising, mainly as a result of increasing population and economic activity. Petroleum fuels remain the dominant energy source, reflecting advantages such as high energy density, low cost, and market availability. The movement of people and freight makes......, cost, distribution, infrastructure, storage, and public acceptability. The transition to low-carbon equitable and sustainable transport will take time but can be fostered by numerous short- and medium-term strategies that would benefit energy security, health, productivity, and sustainability....

  12. Evaluation of public transport

    DEFF Research Database (Denmark)

    Flyvbjerg, Bent; Kahr, Kjeld; Petersen, Peter Bo

    1986-01-01

    by a given supply of transport. In contrast with conventional methods, this method operates with real measures, i.e. real location (instead of traffic zones), real time (instead of average travel time), and real costs (instead of proxy-costs). The purpose is to produce relevant and easily understandable......This paper discusses a method to evaluate sceduled, fixed-route public transport. One major evaluation criterion in the method is total travel time, subdivided into walking time, waiting time, time on vehicle, transfer time, and concealed waiting time. The other major criterion is cost incurred...

  13. Transport research: Quo Vadis?

    CSIR Research Space (South Africa)

    Rust, FC

    2008-07-01

    Full Text Available the national R&D programme in transport became fragmented and consequently very little R&D has been done in the 2000s. This paper analyses the lessons learnt from six historic research programmes in both the public and private sector and in several project...

  14. Transportation cask contamination weeping

    International Nuclear Information System (INIS)

    Bennett, P.C.; Doughty, D.H.; Chambers, W.B.

    1993-01-01

    This paper describes the problem of cask contamination weeping, and efforts to understand the phenomenon and to eliminate its occurrence during spent nuclear fuel transport. The paper summarizes analyses of field experience and scoping experiments, and concentrates on current modelling and experimental validation efforts. (J.P.N.)

  15. Urban Transportation Renewal.

    Science.gov (United States)

    Wolter, Kurt A.; Foster, Patrick N.

    1995-01-01

    Describes a learning activity that involves planning a community and then altering the transportation system to meet new specifications. Includes the rationale for the activity, how it fits into the technology education curriculum, and how it was implemented to fit a variety of age and grade levels. (JOW)

  16. Urban Mass Transportation.

    Science.gov (United States)

    Mervine, K. E.

    This bibliography is part of a series of Environmental Resource Packets prepared under a grant from EXXON Education Foundation. The most authoritative and accessible references in the urban transportation field are reviewed. The authors, publisher, point of view, level, and summary are given for each reference. The references are categorized…

  17. Transport for smart cities

    DEFF Research Database (Denmark)

    Kristensen, Niels Buus; Pedersen, Allan Schrøder

    2011-01-01

    ’ activities can be reached within the relative close distances of the city. However, urbanisation has also led to significant disadvantages, of which transport accounts for some of the most severe. Traffic accidents and emissions of air pollutants and noise take heavy tolls in terms of people killed...

  18. Transport near slippery interfaces

    NARCIS (Netherlands)

    Haase, A. Sander

    2016-01-01

    Some surfaces exhibit wall slip, meaning that a owing uid has a velocity relative to that surface. This leads to increased advection in the direct vicinity of the wall. As this directly a ects the rate of transport at larger scales, slippery surfaces have a potentially important application in

  19. Transport processes in plasmas

    International Nuclear Information System (INIS)

    Balescu, R.

    1988-01-01

    This part is devoted to the neoclassical transport theory. Ch. 8 deals with toroidal magnetic confinement. Ch. 9 studies the motion of an individual particle in a toroidal field. Ch.'s 10 and 11 are devoted to the study of the kinetic equation appropriate to the situation that prevails in the neoclassical theory. Ch. 12 is devoted to the general study of the macroscopic moment equations in toroidal geometry. In ch. 13 the first new transport equations are derived. They include the strange Pfirsch-Schlueter effect. In ch. 14 the method of solution of the kinetic equation in the long free path regime is developed. In ch. 15 the typical long mean free path neoclassical transport equations are obtained and discussed; their very pecular differences with the classicial ones are emphasized. Ch. 16 introduces a mean free path regime as well as a method of interpolation of the results over the whole range of collisionalities. Ch. 17 provides the connection of the transport theory with non-equilibrium thermodynamics in a regime (long mean free path) where the applicability of the latter seems, at first sight, questionable. Nevertheless a complete and consistent thermodynamic theory can be set up, even in this regime. Finally, ch. 18 goes back to the hydrodynamical equations and treats the problem of their closure (in toroidal geometry)

  20. Transport Infrastructure Slot Allocation

    NARCIS (Netherlands)

    Koolstra, K.

    2005-01-01

    In this thesis, transport infrastructure slot allocation has been studied, focusing on selection slot allocation, i.e. on longer-term slot allocation decisions determining the traffic patterns served by infrastructure bottlenecks, rather than timetable-related slot allocation problems. The

  1. Helium transport in TFTR

    International Nuclear Information System (INIS)

    Strachan, J.D.; Chan, A.

    1986-09-01

    Initial measurements of the 15 MeV protons produced in TFTR by the d( 3 He, p)α fusion reaction have been used to determine the time evolution of the central 3 He density. The signals following short 3 He gas puffs indicate inward transport times of about 100 msec

  2. Draft Transportation Institutional Plan

    International Nuclear Information System (INIS)

    1985-09-01

    The Department of Energy recognizes that the success of its program to develop and implement a national system for nuclear waste management and disposal depends on broad-based public understanding and acceptance. While each program element has its particular sensitivity, the transportation of the waste may potentially affect the greatest number of people, and accordingly is highly visible and potentially issue-laden. Therefore, the Office of Civilian Radioactive Waste Management has developed this Transportation Institutional Plan to lay the foundation for interaction among all interested parties for the purpose of identifying and resolving issues of concern. The Plan is divided into four chapters. Chapter 1 provides bachground information and discusses the purpose of the Plan and the policy guidance for establishing the transportation system. Chapter 2 introduces the major participants who must interact to build both the system itself and the consensus philosophy that is essential for effective operations. Chapter 3 suggests mechanisms for interaction that will ensure wide participation in program planning and implementation. And, finally, Chapter 4 suggests a framework for managing and resolving the issues related to development and operation of the transportation system. A list of acronyms and a glossary are included for the reader's convenience. The Plan's appendices provide supporting material to assist the reader in understanding the roles of the involved institutions. 4 figs., 1 tab

  3. Solute transport in soil

    NARCIS (Netherlands)

    Zee, van der S.E.A.T.M.; Leijnse, A.

    2013-01-01

    Solute transport is of importance in view of the movement of nutrient elements, e.g. towards the plant root system, and because of a broad range of pollutants. Pollution is not necessarily man induced, but may be due to geological or geohydrological causes, e.g. in the cases of pollution with

  4. Demographic Change and Transport

    DEFF Research Database (Denmark)

    Haustein, Sonja; Siren, Anu Kristiina; Framke, Elisabeth

    This report is the literature review on demographic changes and transport of Work Package 1 of the EU project CONSOL, “CONcerns and SOLutions – Road Safety in the Ageing Societies” (contract period: 2011-2013). The report is a state-of-the art report that combines current knowledge with new...

  5. What can Transport Deliver?

    DEFF Research Database (Denmark)

    Kobayashi, Shigeki; Fulton, Lewis; Figueroa, Maria J.

    We compare detailed projections of transport energy consumption and CO2 emissions up to the year 2050 and review representative pathways towards the specific mitigation targets outlined in the Fifth Assessment report by the Intergovernmental Panel on Climate Change (IPCC-AR5), contrasting sectora...

  6. Lightweight Monorail Transport System

    Science.gov (United States)

    Weir, Harold F.; Wood, Kenneth E.; Strecker, Myron T.

    1987-01-01

    Report proposes monorail transportation system for zero-gravity environment. System carries materials and parts between locations on space station. Includes tubular rails instead of open channels usually found in overhead conveyor systems. Since resistance to torque of closed tube greater than that of open channel for same amount of material, tubular monorail designed for higher loads or for greater spacing between support points.

  7. Transport properties of liquids

    International Nuclear Information System (INIS)

    Rajagopal, K.

    1976-07-01

    The transport coefficients, self diffusivity, dinamical viscosity,total viscosity (i.e., the first and second viscosity coefficient) and thermal conductivity, are calculated at several temperatures and saturation pressures for the Argon, Krypton and Xenon liquids, from the Mie otential and the hard sphere theory. (L.C.) [pt

  8. Phloem transport in trees

    Science.gov (United States)

    Michael G. Ryan; Shinichi. Asao

    2014-01-01

    Phloem is like an enigmatic central banker: we know how important phloem is to plant function, but very little about how phloem functions as part of a whole-plant economy. Phloem transports carbohydrates, produced by photosynthesis and hydrolysis of reserve compounds, to sink tissues for growth, respiration and storage. At photosynthetic tissues, carbohydrates are...

  9. Artificial oxygen transport protein

    Science.gov (United States)

    Dutton, P. Leslie

    2014-09-30

    This invention provides heme-containing peptides capable of binding molecular oxygen at room temperature. These compounds may be useful in the absorption of molecular oxygen from molecular oxygen-containing atmospheres. Also included in the invention are methods for treating an oxygen transport deficiency in a mammal.

  10. Decentralization in Air Transportation

    NARCIS (Netherlands)

    Udluft, H.

    2017-01-01

    In this work,we demonstrate that decentralized control can result in stable, efficient, and robust operations in the Air Transportation System. We implement decentralized control for aircraft taxiing operations and use Agent-Based Modeling and Simulation to analyze the resulting system behavior

  11. Atomic transport properties

    International Nuclear Information System (INIS)

    Freyss, M.

    2015-01-01

    As presented in the first chapter of this book, atomic transport properties govern a large panel of nuclear fuel properties, from its microstructure after fabrication to its behaviour under irradiation: grain growth, oxidation, fission product release, gas bubble nucleation. The modelling of the atomic transport properties is therefore the key to understanding and predicting the material behaviour under irradiation or in storage conditions. In particular, it is noteworthy that many modelling techniques within the so-called multi-scale modelling scheme of materials make use of atomic transport data as input parameters: activation energies of diffusion, diffusion coefficients, diffusion mechanisms, all of which are then required to be known accurately. Modelling approaches that are readily used or which could be used to determine atomic transport properties of nuclear materials are reviewed here. They comprise, on the one hand, static atomistic calculations, in which the migration mechanism is fixed and the corresponding migration energy barrier is calculated, and, on the other hand, molecular dynamics calculations and kinetic Monte-Carlo simulations, for which the time evolution of the system is explicitly calculated. (author)

  12. Radioactive materials transport experience

    International Nuclear Information System (INIS)

    Langhaar, J.W.

    1976-01-01

    This paper presents a brief review of the kinds of packaging suitable for different types of waste, the roles of highway and rail transport, restrictions imposed by political entities and carriers, and safety. The U. S. accident record is described, with some statistics given

  13. Water transport and energy.

    Science.gov (United States)

    Fricke, Wieland

    2017-06-01

    Water transport in plants occurs along various paths and is driven by gradients in its free energy. It is generally considered that the mode of transport, being either diffusion or bulk flow, is a passive process, although energy may be required to sustain the forces driving water flow. This review aims at putting water flow at the various organisational levels (cell, organ, plant) in the context of the energy that is required to maintain these flows. In addition, the question is addressed (1) whether water can be transported against a difference in its chemical free energy, 'water potential' (Ψ), through, directly or indirectly, active processes; and (2) whether the energy released when water is flowing down a gradient in its energy, for example during day-time transpiration and cell expansive growth, is significant compared to the energy budget of plant and cell. The overall aim of review is not so much to provide a definite 'Yes' and 'No' to these questions, but rather to stimulate discussion and raise awareness that water transport in plants has its real, associated, energy costs and potential energy gains. © 2016 John Wiley & Sons Ltd.

  14. VIVITRON beam transport

    International Nuclear Information System (INIS)

    Nadji, A.

    1989-07-01

    The VIVITRON is a new 35 MV particle accelerator which presents a great number of innovations. One of the major problem is the beam transport in this electrostatic machine of 50 m length for ions with masses between 1 and 200. Our work consisted in the study of various experimental and theoretical aspects of the beam transport in Tandem accelerators from the ion source to the analysing magnet. Calculations of the beam optics were performed with a Strasbourg version of the computer code Transport. They allowed us to optimize the beam transport parameters of the VIVITRON elements. Special attention has been focused on the design of the charge state selector to be installed in the terminal of the new machine. Beam transmission measurements were carried out in the Strasbourg MP 10 Tandem accelerator for ions beams of masses between 1 and 127 and for terminal voltages from 9 to 15 MV. Partial and total transmissions were obtained and explanations of the beam losses were proposed in terms of the vacuum pressure and/or the optics of the beam accelerator system. The results have been extrapolated to the VIVITRON for which the best working conditions are now clearly defined [fr

  15. Bystruktur og transport

    DEFF Research Database (Denmark)

    Nielsen, Thomas Alexander Sick

    2003-01-01

    Paperet præsenterer hovedkonklusionerne fra et PhD-studie af sammenhængene mellem bystruktur (særligt boliglokalisering) og transport i Aalborg. Det konkluderes at boliglokaliseringen har væsentlig betydning for transporten i det daglige. Det gælder især lokaliseringen i forhold til det samlede...

  16. Saturated Zone Colloid Transport

    International Nuclear Information System (INIS)

    H. S. Viswanathan

    2004-01-01

    This scientific analysis provides retardation factors for colloids transporting in the saturated zone (SZ) and the unsaturated zone (UZ). These retardation factors represent the reversible chemical and physical filtration of colloids in the SZ. The value of the colloid retardation factor, R col is dependent on several factors, such as colloid size, colloid type, and geochemical conditions (e.g., pH, Eh, and ionic strength). These factors are folded into the distributions of R col that have been developed from field and experimental data collected under varying geochemical conditions with different colloid types and sizes. Attachment rate constants, k att , and detachment rate constants, k det , of colloids to the fracture surface have been measured for the fractured volcanics, and separate R col uncertainty distributions have been developed for attachment and detachment to clastic material and mineral grains in the alluvium. Radionuclides such as plutonium and americium sorb mostly (90 to 99 percent) irreversibly to colloids (BSC 2004 [DIRS 170025], Section 6.3.3.2). The colloid retardation factors developed in this analysis are needed to simulate the transport of radionuclides that are irreversibly sorbed onto colloids; this transport is discussed in the model report ''Site-Scale Saturated Zone Transport'' (BSC 2004 [DIRS 170036]). Although it is not exclusive to any particular radionuclide release scenario, this scientific analysis especially addresses those scenarios pertaining to evidence from waste-degradation experiments, which indicate that plutonium and americium may be irreversibly attached to colloids for the time scales of interest. A section of this report will also discuss the validity of using microspheres as analogs to colloids in some of the lab and field experiments used to obtain the colloid retardation factors. In addition, a small fraction of colloids travels with the groundwater without any significant retardation. Radionuclides irreversibly

  17. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

    2000-01-30

    This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

  18. Nevada Transportation Options Study

    International Nuclear Information System (INIS)

    P. GEHNER; E.M. WEAVER; L. FOSSUM

    2006-01-01

    This study performs a cost and schedule analysis of three Nevada Transportation options that support waste receipt at the repository. Based on the U.S. Department of Energy preference for rail transportation in Nevada (given in the Final Environmental Impact Statement), it has been assumed that a branch rail line would be constructed to support waste receipt at the repository. However, due to potential funding constraints, it is uncertain when rail will be available. The three Nevada Transportation options have been developed to meet a varying degree of requirements for transportation and to provide cost variations used in meeting the funding constraints given in the Technical Direction Letter guidelines for this study. The options include combinations of legal-weight truck, heavy-haul truck, and rail. Option 1 uses a branch rail line that would support initial waste receipt at the repository in 2010. Rail transportation would be the primary mode, supplemented by legal weight trucks. This option provides the highest level of confidence in cost and schedule, lowest public visibility, greatest public acceptability, lowest public dose, and is the recommended option for support of waste receipt. The completion of rail by 2010 will require spending approximately $800 million prior to 2010. Option 2 uses a phased rail approach to address a constrained funding scenario. To meet funding constraints, Option 2 uses a phased approach to delay high cost activities (final design and construction) until after initial waste receipt in 2010. By doing this, approximately 95 percent of the cost associated with completion of a branch rail line is deferred until after 2010. To support waste receipt until a branch rail line is constructed in Nevada, additional legal-weight truck shipments and heavy-haul truck shipments (on a limited basis for naval spent nuclear fuel) would be used to meet the same initial waste receipt rates as in Option 1. Use of heavy-haul shipments in the absence

  19. Sustainable Transport and Performance Indicators

    DEFF Research Database (Denmark)

    Gudmundsson, H.

    2004-01-01

    ustainable transport has become a major policy concern in recent years. The term suggests a need to consider transport in a comprehensive perspective including the well-being of both present and future generations, and taking environmental, social and economic issues into account. Indicators...... in forecasting and tracking the performance of transport systems increasingly guide sustainable transport policy making. This review explores the implications of the "sustainable transport" concept and how it can be made operational with indicators. A number of indicator systems are reviewed, and some strengths...... and weaknesses are highlighted with regard to the support they provide for sustainable transport development....

  20. Transportation-Related Consumer Preference Data | Transportation Research |

    Science.gov (United States)

    NREL Transportation-Related Consumer Preference Data Transportation-Related Consumer Preference Data Photo of reporters test driving Toyota prototype electric and fuel cell vehicles. Consumer for the development and implementation of these technologies. NREL collects, analyzes, and reports on

  1. SAFETY AND QUALITY CONTROL OF TRANSPORT SERVICES ON RAILWAY TRANSPORT

    Directory of Open Access Journals (Sweden)

    I. P. Sadlovska

    2010-10-01

    Full Text Available The article presents the provisions to improve procedure of licensing of passenger and freight transportation, technical specifications for services related to the passenger and freight transportations.

  2. Transportation programs : challenges facing the department of transportation and congress.

    Science.gov (United States)

    2009-03-01

    A safe, efficient, and convenient : transportation system is integral to : the health of our economy and : quality of life. Our nations vast : transportation system of airways, : railways, roads, transit systems, : and waterways has served this : ...

  3. Transporter taxonomy - a comparison of different transport protein classification schemes.

    Science.gov (United States)

    Viereck, Michael; Gaulton, Anna; Digles, Daniela; Ecker, Gerhard F

    2014-06-01

    Currently, there are more than 800 well characterized human membrane transport proteins (including channels and transporters) and there are estimates that about 10% (approx. 2000) of all human genes are related to transport. Membrane transport proteins are of interest as potential drug targets, for drug delivery, and as a cause of side effects and drug–drug interactions. In light of the development of Open PHACTS, which provides an open pharmacological space, we analyzed selected membrane transport protein classification schemes (Transporter Classification Database, ChEMBL, IUPHAR/BPS Guide to Pharmacology, and Gene Ontology) for their ability to serve as a basis for pharmacology driven protein classification. A comparison of these membrane transport protein classification schemes by using a set of clinically relevant transporters as use-case reveals the strengths and weaknesses of the different taxonomy approaches.

  4. Rotation, Stability and Transport

    Energy Technology Data Exchange (ETDEWEB)

    Connor, J. W.

    2007-07-01

    Tokamak plasmas can frequently exhibit high levels of rotation and rotation shear. This can usually be attributed to various sources: injection of momentum, e.g. through neutral beams, flows driven by plasma gradients or torques resulting from non-ambipolar particle loss; however, the source sometimes remains a mystery, such as the spontaneous rotation observed in Ohmic plasmas. The equilibrium rotation profile is given by the balance of these sources with transport and other losses; the edge boundary conditions can play an important role in determining this profile . Such plasma rotation, particularly sheared rotation, is predicted theoretically to have a significant influence on plasma behaviour. In the first place, sonic flows can significantly affect tokamak equilibria and neoclassical transport losses. However, the influence of rotation on plasma stability and turbulence is more profound. At the macroscopic level it affects the behaviour of the gross MHD modes that influence plasma operational limits. This includes sawteeth, the seeding of neoclassical tearing modes, resistive wall modes and the onset of disruptions through error fields, mode locking and reconnection. At the microscopic level it has a major effect on the stability of ballooning modes, both ideal MHD and drift wave instabilities such as ion temperature gradient (ITG) modes. In the non-linear state, as unstable drift waves evolve into turbulent structures, sheared rotation also tears apart eddies, thereby reducing the resulting transport. There is considerable experimental evidence for these effects on both MHD stability and plasma confinement. In particular, the appearance of improved confinement modes with transport barriers, such as edge H-mode barriers and internal transport barriers (ITBs) appears to correlate well with the presence of sheared plasma rotation. This talk will describe the theory underlying some of these phenomena involving plasma rotation, on both macroscopic and microscopic

  5. EBS Radionuclide Transport Abstraction

    International Nuclear Information System (INIS)

    Schreiner, R.

    2001-01-01

    The purpose of this work is to develop the Engineered Barrier System (EBS) radionuclide transport abstraction model, as directed by a written development plan (CRWMS M and O 1999a). This abstraction is the conceptual model that will be used to determine the rate of release of radionuclides from the EBS to the unsaturated zone (UZ) in the total system performance assessment-license application (TSPA-LA). In particular, this model will be used to quantify the time-dependent radionuclide releases from a failed waste package (WP) and their subsequent transport through the EBS to the emplacement drift wall/UZ interface. The development of this conceptual model will allow Performance Assessment Operations (PAO) and its Engineered Barrier Performance Department to provide a more detailed and complete EBS flow and transport abstraction. The results from this conceptual model will allow PA0 to address portions of the key technical issues (KTIs) presented in three NRC Issue Resolution Status Reports (IRSRs): (1) the Evolution of the Near-Field Environment (ENFE), Revision 2 (NRC 1999a), (2) the Container Life and Source Term (CLST), Revision 2 (NRC 1999b), and (3) the Thermal Effects on Flow (TEF), Revision 1 (NRC 1998). The conceptual model for flow and transport in the EBS will be referred to as the ''EBS RT Abstraction'' in this analysis/modeling report (AMR). The scope of this abstraction and report is limited to flow and transport processes. More specifically, this AMR does not discuss elements of the TSPA-SR and TSPA-LA that relate to the EBS but are discussed in other AMRs. These elements include corrosion processes, radionuclide solubility limits, waste form dissolution rates and concentrations of colloidal particles that are generally represented as boundary conditions or input parameters for the EBS RT Abstraction. In effect, this AMR provides the algorithms for transporting radionuclides using the flow geometry and radionuclide concentrations determined by other

  6. On the relation between neoclassical transport and turbulent transport

    International Nuclear Information System (INIS)

    Shaing, K.C.

    2005-01-01

    It is demonstrated through the flux-force relationship in the neoclassical theory that when neoclassical transport fluxes are improved, the damping rate of the radial electric field of the zonal flow is reduced. This, in turn, leads to improved turbulent transport fluxes. Thus, two seemingly unrelated transport fluxes are intimately connected through the momentum equation, and the neoclassical flux-force relation. This also implies a method to improve turbulent transport by improving neoclassical fluxes

  7. Perspectives of transport logistics in the railway transport enterprises

    OpenAIRE

    Elagin, Yu; Obruch, A.

    2014-01-01

    In this paper, the authors study the main directions of development of transport logistics. Identified as the main types of general transport logistics, as well as the rail sector, in which logistics acquires a dominant role in terms of reform. Also highlights the main features of transport logistics for railway transport enterprises and proved the importance of integrating function in modern conditions of development. The authors noted that to ensure the effective development of railway tran...

  8. Mass Transport within Soils

    Energy Technology Data Exchange (ETDEWEB)

    McKone, Thomas E.

    2009-03-01

    Contaminants in soil can impact human health and the environment through a complex web of interactions. Soils exist where the atmosphere, hydrosphere, geosphere, and biosphere converge. Soil is the thin outer zone of the earth's crust that supports rooted plants and is the product of climate and living organisms acting on rock. A true soil is a mixture of air, water, mineral, and organic components. The relative proportions of these components determine the value of the soil for agricultural and for other human uses. These proportions also determine, to a large extent, how a substance added to soil is transported and/or transformed within the soil (Spositio, 2004). In mass-balance models, soil compartments play a major role, functioning both as reservoirs and as the principal media for transport among air, vegetation, surface water, deeper soil, and ground water (Mackay, 2001). Quantifying the mass transport of chemicals within soil and between soil and atmosphere is important for understanding the role soil plays in controlling fate, transport, and exposure to multimedia pollutants. Soils are characteristically heterogeneous. A trench dug into soil typically reveals several horizontal layers having different colors and textures. As illustrated in Figure 1, these multiple layers are often divided into three major horizons: (1) the A horizon, which encompasses the root zone and contains a high concentration of organic matter; (2) the B horizon, which is unsaturated, lies below the roots of most plants, and contains a much lower organic carbon content; and (3) the C horizon, which is the unsaturated zone of weathered parent rock consisting of bedrock, alluvial material, glacial material, and/or soil of an earlier geological period. Below these three horizons lies the saturated zone - a zone that encompasses the area below ground surface in which all interconnected openings within the geologic media are completely filled with water. Similarly to the unsaturated

  9. Nuclear fuel transport and particularly spent fuel transport

    International Nuclear Information System (INIS)

    Lenail, B.

    1986-01-01

    Nuclear material transport is an essential activity for COGEMA linking the different steps of the fuel cycle transport systems have to be safe and reliable. Spent fuel transport is more particularly examined in this paper because the development of reprocessing plant. Industrial, techmical and economical aspects are reviewed [fr

  10. Competitiveness in Road Transport

    DEFF Research Database (Denmark)

    Borgström, Benedikte; Gammelgaard, Britta; Bruun, Poul

    Road transport is an important sector, connecting time and space of production and consumption. Its market conditions has changed. The EU single market implementation has increased price pressure due to supply of low cost road freight transport from counties with lower cost structures. Changes...... in the market also encourage strategic development of some road hauliers into providers of unique services. Such road haulier strategic development contributes to efficiency and effectiveness in basically all business sectors of EU. Little research is available of such strategic and operational management....... In this paper we will explore that knowledge gap and analyze what value proposition(s) and capabilities can transform potential cost disadvantages of acting in a market that includes both high- and low-cost-country actors? And in conceptual terminology, how are capabilities deployed and developed to construct...

  11. Anomalous transport in tokamaks

    International Nuclear Information System (INIS)

    Wootton, A.J.

    1989-01-01

    A review is presented of what is known about anomalous transport in tokamaks. It is generally thought that this anomalous transport is the result of fluctuations in various plasma parameters. In the plasma edge detailed measurements of the quantities required to directly determine the fluctuation driven fluxes are available. The total flux of particles is well explained by the measured electrostatic fluctuation driven flux. However, a satisfactory model to explain the origin of the fluctuations has not been identified. The processes responsible for determining the edge energy flux are less clear, but electrostatic convection plays an important part. In the confinement region experimental observations are presently restricted to measurements of density and potential fluctuations and their correlations. The characteristics of the measured fluctuations are discussed and compared with the predictions of various models. Comparisons between measured particle, electron heat and ion heat fluxes, and those fluxes predicted to result from the measured fluctuations, are made. Magnetic fluctuations is discussed

  12. Rail transport systems approach

    CERN Document Server

    2017-01-01

    This book shows how the systems approach is employed by scientists in various countries to solve specific problems concerning railway transport. In particular, the book describes the experiences of scientists from Romania, Germany, the Czech Republic, the UK, Russia, Ukraine, Lithuania and Poland. For many of these countries there is a problem with the historical differences between the railways. In particular, there are railways with different rail gauges, with different signaling and communication systems, with different energy supplies and, finally, with different political systems, which are reflected in the different approaches to the management of railway economies. The book’s content is divided into two main parts, the first of which provides a systematic analysis of individual means of providing and maintaining rail transport. In turn, the second part addresses infrastructure and management development, with particular attention to security issues. Though primarily written for professionals involved...

  13. Near field transport processes

    International Nuclear Information System (INIS)

    Neretnieks, I.

    1991-01-01

    In repositories for nuclear waste there are many processes which will be instrumental in corroding the canisters and releasing the nuclides. Based on experiences from studies on the performance of repositories and on an actual design the major mechanisms influencing the integrity and performance of a repository are described and discussed. The paper addresses only conditions in crystalline rock repositories. The low water flow rate in fractures and channels plays a dominant role in limiting the interaction between water and waste. Molecular diffusion in the backfill and rock matrix as well as in the mobile water is an important transport process but actually limits the exchange rate because diffusive transport is slow. Solubility limits of both waste matrix and of individual nuclides are also important. Complicating processes include gas generation by iron corrosion and alpha-radiolysis. (au) (19 refs., 2 figs.)

  14. Cellular iron transport.

    Science.gov (United States)

    Garrick, Michael D; Garrick, Laura M

    2009-05-01

    Iron has a split personality as an essential nutrient that also has the potential to generate reactive oxygen species. We discuss how different cell types within specific tissues manage this schizophrenia. The emphasis in enterocytes is on regulating the body's supply of iron by regulating transport into the blood stream. In developing red blood cells, adaptations in transport manage the body's highest flux of iron. Hepatocytes buffer the body's stock of iron. Macrophage recycle the iron from effete red cells among other iron management tasks. Pneumocytes provide a barrier to prevent illicit entry that, when at risk of breaching, leads to a need to handle the dangers in a fashion essentially shared with macrophage. We also discuss or introduce cell types including renal cells, neurons, other brain cells, and more where our ignorance, currently still vast, needs to be removed by future research.

  15. Shielded Canister Transporter

    International Nuclear Information System (INIS)

    Eidem, G.G. Jr.; Fages, R.

    1993-01-01

    The Hanford Waste Vitrification Plant (HWVP) will produce canisters filled with high-level radioactive waste immobilized in borosilicate glass. This report discusses a Shielded Canister Transporter (SCT) which will provide the means for safe transportation and handling of the canisters from the Vitrification Building to the Canister Storage Building (CSB). The stainless steel canisters are 0.61 meters in diameter, 3.0 meters tall, and weigh approximately 2,135 kilograms, with a maximum exterior surface dose rate of 90,000 R/hr. The canisters are placed into storage tubes to a maximum of three tall (two for overpack canisters) with an impact limiter placed at the tube bottom and between each canister. A floor plug seals the top of the storage tube at the operating floor level of the CSB

  16. GERENCIAMENTO DE TRANSPORTE COLETIVO

    Directory of Open Access Journals (Sweden)

    Milena Bodmer

    2010-05-01

    Full Text Available Trata-se da primeira produção acadêmica voltada para as necessidades do setor de transporte de passageiros. O trabalho, destinado não só aos executivos das empresas, como também aos técnicos, aos pesquisadores e consultores da área de transporte de passageiros, traz no seu bojo a preocupação de aproximar as contribuições teóricas ao estado da prática nas empresas operadoras. O livro, através dos seus oito capítulos, abre as portas para os tópicos que devem ser considerados essenciais para as possibilidades de aperfeiçoamento e modernização gerencial.

  17. retardo de transporte

    Directory of Open Access Journals (Sweden)

    Paola Niño-Suárez

    2006-01-01

    Full Text Available En este trabajo se presenta la obtención del modelo exacto en tiempo discreto de un robot móvil tipo (2,0, bajo la consideración de la existencia de retardos de transporte en la señal de control, producidos por la propagación de las señales entre los sensores y actuadores del robot y el control remoto. El modelo obtenido es evaluado mediante simulación, comparando su desempeño con un modelo discreto aproximado que incluye también retardos de transporte y con el modelo en tiempo continuo del mismo sistema.

  18. Axisymmetric tokamak scapeoff transport

    International Nuclear Information System (INIS)

    Singer, C.E.; Langer, W.D.

    1982-08-01

    We present the first self-consistent estimate of the magnitude of each term in a fluid treatment of plasma transport for a plasma lying in regions of open field lines in an axisymmetric tokamak. The fluid consists of a pure hydrogen plasma with sources which arise from its interaction with neutral hydrogen atoms. The analysis and results are limited to the high collisionality regime, which is optimal for a gaseous neutralizer divertor, or to a cold plasma mantle in a tokamak reactor. In this regime, both classical and neoclassical transport processes are important, and loss of particles and energy by diamagnetic flow are also significant. The prospect of extending the analysis to the lower collisionality regimes encountered in many existing experiments is discussed

  19. Fuel cell water transport

    Science.gov (United States)

    Vanderborgh, Nicholas E.; Hedstrom, James C.

    1990-01-01

    The moisture content and temperature of hydrogen and oxygen gases is regulated throughout traverse of the gases in a fuel cell incorporating a solid polymer membrane. At least one of the gases traverses a first flow field adjacent the solid polymer membrane, where chemical reactions occur to generate an electrical current. A second flow field is located sequential with the first flow field and incorporates a membrane for effective water transport. A control fluid is then circulated adjacent the second membrane on the face opposite the fuel cell gas wherein moisture is either transported from the control fluid to humidify a fuel gas, e.g., hydrogen, or to the control fluid to prevent excess water buildup in the oxidizer gas, e.g., oxygen. Evaporation of water into the control gas and the control gas temperature act to control the fuel cell gas temperatures throughout the traverse of the fuel cell by the gases.

  20. Transporting radioactive rock

    International Nuclear Information System (INIS)

    Pearce, G.

    1990-01-01

    The case is made for exempting geological specimens from the IAEA Regulations for Safer Transport of Radioactive Materials. It is pointed out that many mineral collectors in Devon and Cornwall may be unwittingly infringing these regulations by taking naturally radioactive rocks and specimens containing uranium ores. Even if these collectors are aware that these rocks are radioactive, and many are not, few have the necessary equipment to monitor the activity levels. If the transport regulations were to be enforced alarm could be generated and the regulations devalued in case of an accident. The danger from a spill of rock specimens is negligible compared with an accident involving industrial or medical radioactive substances yet would require similar special treatment. (UK)

  1. Archiving Data from New Survey Technologies: Lessons Learned on Enabling Research with High-Precision Data While Preserving Participant Privacy: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Gonder, J.; Burton, E.; Murakami, E.

    2014-11-01

    During the past 15 years, increasing numbers of organizations and planning agencies have begun collecting high-resolution Global Positioning System (GPS) travel data. Despite the significant effort and expense to collect it, privacy concerns often lead to underutilization of the data. To address this dilemma of providing data access while preserving privacy, the National Renewable Energy Laboratory, with support from the U.S. Department of Transportation and U.S. Department of Energy, established the Transportation Secure Data Center (TSDC). Lessons drawn from best-practice examples from other data centers have helped shape the structure and operating procedures for the TSDC, which functions under the philosophy of first and foremost preserving privacy, but doing so in a way that balances security with accessibility and usability of the data for legitimate research. This paper provides details about the TSDC approach toward achieving these goals, which has included creating a secure enclave with no external access for backing up and processing raw data, a publicly accessible website for downloading cleansed data, and a secure portal environment through which approved users can work with detailed spatial data using a variety of tools and reference information. This paper also describes lessons learned from operating the TSDC with respect to improvements in GPS data handling, processing, and user support, along with plans for continual enhancements to better support the needs of both data providers and users and to thus advance the research value derived from such valuable data.

  2. Transport of radioactive material

    International Nuclear Information System (INIS)

    Lombard, J.

    1996-01-01

    This work deals with the transport of radioactive materials. The associated hazards and potential hazards are at first described and shows the necessity to define specific safety regulations. The basic principles of radiological protection and of the IAEA regulations are given. The different types of authorized packages and of package labelling are explained. The revision, updating and the monitoring of the regulations effectiveness is the subject of the last part of this conference. (O.M.)

  3. Radioactive material transport

    International Nuclear Information System (INIS)

    White, M.C.

    1979-10-01

    All movements of radioactive materials in Canada are governed by a comprehensive body of regqlations, both national and international. These regulations are designed to maximize shielding to the public and transport workers, allow for heat dissipation, and to prevent criticality accidents, by prescribing specific packaging arrangements, administrative controls, labelling and storage measures. This report describes in some detail specific requirements and summarizes some incidents that occurred between 1974 and 1978

  4. Urban Transport and Communication

    International Nuclear Information System (INIS)

    Irandu, E.M.

    1999-01-01

    The population according to the 1989 census was 21,448,774 inhabitants. This figure shows that on average the total population has been increasing by more than 40% every decade since 1948. As a result the widening gap between fertility and mortality, the population is growing at an accelerated rate. The current official population growth rate figure of 3.4% per annum puts the country among the world's most rapidly growing nations. It is projected that by the year 2010, the population will be about 37.4 million. At present the urban centres with a population size of 2,000 people and above constitute about 18.1% of the total population (Kenya, 1994). Rapid economic growth has led to the development of a number of urban centres as centres of commerce, industry and tourism. Consequently, this has led to rural urban drift. This drift to urban areas causes a number of problems which if unresolved will limit the ability of the urban centres to support their population The rapid increase in urban population causes a shortage of facilities to meet the increasing demand in services such as public transport, water supply, sewage and housing (Ramatullah, 1997: 161-168). Urban Transport acts as catalyst to both urban and national development, by facilitating the movements associated with urban and national Development. They provide a means by which goods and services are made available to industry and consumers, creating opportunity for social and economic interaction and employment. Without urban transport, access to health, education and employment would not be possible. Indeed urban transport is what gives life to urban development

  5. Transport phenomena II essentials

    CERN Document Server

    REA, The Editors of

    2012-01-01

    REA's Essentials provide quick and easy access to critical information in a variety of different fields, ranging from the most basic to the most advanced. As its name implies, these concise, comprehensive study guides summarize the essentials of the field covered. Essentials are helpful when preparing for exams, doing homework and will remain a lasting reference source for students, teachers, and professionals. Transport Phenomena II covers forced convention, temperature distribution, free convection, diffusitivity and the mechanism of mass transfer, convective mass transfer, concentration

  6. Beam Extraction and Transport

    CERN Document Server

    Kalvas, T.

    2013-12-16

    This chapter gives an introduction to low-energy beam transport systems, and discusses the typically used magnetostatic elements (solenoid, dipoles and quadrupoles) and electrostatic elements (einzel lens, dipoles and quadrupoles). The ion beam emittance, beam space-charge effects and the physics of ion source extraction are introduced. Typical computer codes for analysing and designing ion optical systems are mentioned, and the trajectory tracking method most often used for extraction simulations is described in more detail.

  7. Energy use in transport

    Energy Technology Data Exchange (ETDEWEB)

    Allan, R. R.

    1977-10-15

    Brief data and information on consumption of oil-based fuels in New Zealand transport are presented. Then the role of the private car, conservation attitudes and behavior, social impacts of energy conservation are discussed. Apart from the methanol and LP-gas options which do not conserve energy, but only substitute energy sources by local supplies, noticeable fuel savings without sacrificing mobility and changing living patterns can be achieved only by concerted implementation of a package of measures.

  8. Transport Phenomena in Gel

    Directory of Open Access Journals (Sweden)

    Masayuki Tokita

    2016-05-01

    Full Text Available Gel becomes an important class of soft materials since it can be seen in a wide variety of the chemical and the biological systems. The unique properties of gel arise from the structure, namely, the three-dimensional polymer network that is swollen by a huge amount of solvent. Despite the small volume fraction of the polymer network, which is usually only a few percent or less, gel shows the typical properties that belong to solids such as the elasticity. Gel is, therefore, regarded as a dilute solid because its elasticity is much smaller than that of typical solids. Because of the diluted structure, small molecules can pass along the open space of the polymer network. In addition to the viscous resistance of gel fluid, however, the substance experiences resistance due to the polymer network of gel during the transport process. It is, therefore, of importance to study the diffusion of the small molecules in gel as well as the flow of gel fluid itself through the polymer network of gel. It may be natural to assume that the effects of the resistance due to the polymer network of gel depends strongly on the network structure. Therefore, detailed study on the transport processes in and through gel may open a new insight into the relationship between the structure and the transport properties of gel. The two typical transport processes in and through gel, that is, the diffusion of small molecules due to the thermal fluctuations and the flow of gel fluid that is caused by the mechanical pressure gradient will be reviewed.

  9. Polaronic transport in polysilanes

    Czech Academy of Sciences Publication Activity Database

    Nešpůrek, Stanislav; Nožár, Juraj; Kadashchuk, A.; Fishchuk, I. I.

    2009-01-01

    Roč. 193, č. 1 (2009), s. 1-4 ISSN 1742-6588. [International Conference on Electron Dynamics in Semiconductors, Optoelectronics and Nanostructures /16./. Montpellier, 24.08.2009-28.08.2009] R&D Projects: GA AV ČR IAA100100622; GA AV ČR KAN400720701 Institutional research plan: CEZ:AV0Z40500505 Keywords : polaronic transport * polysilanes * charge carrier mobility Subject RIV: CD - Macromolecular Chemistry

  10. Ion transport in stellarators

    International Nuclear Information System (INIS)

    Ho, D.D.M.; Kulsrud, R.M.

    1985-09-01

    Stellarator ion transport in the low-collisionality regime with a radial electric field is calculated by a systematic expansion of the drift-Boltzmann equation. The shape of the helical well is taken into account in this calculation. It is found that the barely trapped ions with three to four times the thermal energy give the dominant contribution to the diffusion. Expressions for the ion particle and energy fluxes are derived

  11. Transportation of medical isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, D.L.

    1997-11-19

    A Draft Technical Information Document (HNF-1855) is being prepared to evaluate proposed interim tritium and medical isotope production at the Fast Flux Test Facility (FFTF). This assessment examines the potential health and safety impacts of transportation operations associated with the production of medical isotopes. Incident-free and accidental impacts are assessed using bounding source terms for the shipment of nonradiological target materials to the Hanford Site, the shipment of irradiated targets from the FFTF to the 325 Building, and the shipment of medical isotope products from the 325 Building to medical distributors. The health and safety consequences to workers and the public from the incident-free transportation of targets and isotope products would be within acceptable levels. For transportation accidents, risks to works and the public also would be within acceptable levels. This assessment is based on best information available at this time. As the medical isotope program matures, this analysis will be revised, if necessary, to support development of a final revision to the Technical Information Document.

  12. Multiscale thermal transport.

    Energy Technology Data Exchange (ETDEWEB)

    Graham, Samuel Jr. (; .); Wong, C. C.; Piekos, Edward Stanley

    2004-02-01

    A concurrent computational and experimental investigation of thermal transport is performed with the goal of improving understanding of, and predictive capability for, thermal transport in microdevices. The computational component involves Monte Carlo simulation of phonon transport. In these simulations, all acoustic modes are included and their properties are drawn from a realistic dispersion relation. Phonon-phonon and phonon-boundary scattering events are treated independently. A new set of phonon-phonon scattering coefficients are proposed that reflect the elimination of assumptions present in earlier analytical work from the simulation. The experimental component involves steady-state measurement of thermal conductivity on silicon films as thin as 340nm at a range of temperatures. Agreement between the experiment and simulation on single-crystal silicon thin films is excellent, Agreement for polycrystalline films is promising, but significant work remains to be done before predictions can be made confidently. Knowledge gained from these efforts was used to construct improved semiclassical models with the goal of representing microscale effects in existing macroscale codes in a computationally efficient manner.

  13. Thermalhydraulics and activity transport

    International Nuclear Information System (INIS)

    McDonald, B.H.; Wren, D.J.

    1990-01-01

    The potential consequences of a reactor accident, in terms of its impact on public safety, rest on the source term of radioactive fission products. The source term, as, as defined by an international group of experts, is the quantity of radioactive material which might be released in a nuclear accident: its physical and chemical form and the other quantities needed to completely specify its dispersion in the environment (e.g., energy in the plume, height of release, duration of release etc.). Although there are a large number of physical and chemical factors that will contribute to the determination of the source term for a given accident scenario, those factors having a direct impact on the rate of transport are of obvious importance. The thermalhydraulic conditions controlling the rate of mass transport, among other things, are probably the most important factors influencing the source term. This paper is an overview of the areas in which thermalhydraulics most strongly influences activity transport during a severe accident in a water-cooled reactor. It also includes some discussion of the areas where coupling between the physics used in separate computer models of the two phenomena must be considered in any mechanistic best-estimate calculations of the source term

  14. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

    1999-10-15

    This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

  15. Energy transport in dendrimers

    International Nuclear Information System (INIS)

    Supritz, C.; Engelmann, A.; Reineker, P.

    2006-01-01

    Dendrimers are highly branched polymers which are expected to be useful, for example, as efficient artificial light harvesting systems in nano-technological applications. There are two different classes of dendrimers: compact dendrimers with constant distance between neighboring branching points throughout the macromolecule and extended dendrimers where this distance increases from the system periphery to the center. An open question is still whether energy transport (via Frenkel excitons) occurs in a coherent or incoherent manner. We model the hyperbranched dendrimer molecule as an arrangement of two-level systems and apply the Frenkel exciton concept. The two-level systems are interacting with each other via transfer integrals modeling the special spatial structure of dendrimers. To take into account the electron-phonon interaction we introduce a heat bath that interacts with the exciton in a stochastic manner. In this way we describe the coupled coherent and incoherent Frenkel exciton transport inside a dendrimer. In order to mimic the influence of an energy capturing reaction center (like in photosynthesis) on exciton transport, we attach a sink to the dendrimer core

  16. Energy transport in dendrimers

    Energy Technology Data Exchange (ETDEWEB)

    Supritz, C. [Abteilung Theoretische Physik, Universitaet Ulm, Albert-Einstein-Allee 11, 89069 Ulm (Germany)]. E-mail: christoph.supritz@uni-ulm.de; Engelmann, A. [Abteilung Theoretische Physik, Universitaet Ulm, Albert-Einstein-Allee 11, 89069 Ulm (Germany); Reineker, P. [Abteilung Theoretische Physik, Universitaet Ulm, Albert-Einstein-Allee 11, 89069 Ulm (Germany)

    2006-07-15

    Dendrimers are highly branched polymers which are expected to be useful, for example, as efficient artificial light harvesting systems in nano-technological applications. There are two different classes of dendrimers: compact dendrimers with constant distance between neighboring branching points throughout the macromolecule and extended dendrimers where this distance increases from the system periphery to the center. An open question is still whether energy transport (via Frenkel excitons) occurs in a coherent or incoherent manner. We model the hyperbranched dendrimer molecule as an arrangement of two-level systems and apply the Frenkel exciton concept. The two-level systems are interacting with each other via transfer integrals modeling the special spatial structure of dendrimers. To take into account the electron-phonon interaction we introduce a heat bath that interacts with the exciton in a stochastic manner. In this way we describe the coupled coherent and incoherent Frenkel exciton transport inside a dendrimer. In order to mimic the influence of an energy capturing reaction center (like in photosynthesis) on exciton transport, we attach a sink to the dendrimer core.

  17. The transport safety programme

    International Nuclear Information System (INIS)

    Selling, H.A.

    1994-01-01

    The transport safety programme is one of the smaller technical sub-programmes in the Radiation Safety Section of the Division of Nuclear Safety, in terms of both regular budget and professional staff allocations. The overall aim of the programme is to promote the safe movement of radioactive material worldwide. The specific objectives are the development, review and maintenance of the Regulations for the Safe Transport of Radioactive Material, Safety Series No 6, and its supporting documents Safety Series Nos 7, 37 and 80 and the assistance to Member States and International Organizations in the proper implementation of the Regulations. One of the important issues that emerged during an ongoing Review/Revision process is the transport of Low-Specific Activity (LSA) material and Surface Contaminated Objects (SCO). Many of the radioactive waste materials fall in one of these categories. The subject has gained substance because it is expected that in the next decade radioactive waste could become available in so far unprecedented quantities and volumes due to decontamination and decommissioning of nuclear facilities. (author)

  18. Transportation of medical isotopes

    International Nuclear Information System (INIS)

    Nielsen, D.L.

    1997-01-01

    A Draft Technical Information Document (HNF-1855) is being prepared to evaluate proposed interim tritium and medical isotope production at the Fast Flux Test Facility (FFTF). This assessment examines the potential health and safety impacts of transportation operations associated with the production of medical isotopes. Incident-free and accidental impacts are assessed using bounding source terms for the shipment of nonradiological target materials to the Hanford Site, the shipment of irradiated targets from the FFTF to the 325 Building, and the shipment of medical isotope products from the 325 Building to medical distributors. The health and safety consequences to workers and the public from the incident-free transportation of targets and isotope products would be within acceptable levels. For transportation accidents, risks to works and the public also would be within acceptable levels. This assessment is based on best information available at this time. As the medical isotope program matures, this analysis will be revised, if necessary, to support development of a final revision to the Technical Information Document

  19. Bubble transport in bifurcations

    Science.gov (United States)

    Bull, Joseph; Qamar, Adnan

    2017-11-01

    Motivated by a developmental gas embolotherapy technique for cancer treatment, we examine the transport of bubbles entrained in liquid. In gas embolotherapy, infarction of tumors is induced by selectively formed vascular gas bubbles that originate from acoustic vaporization of vascular droplets. In the case of non-functionalized droplets with the objective of vessel occlusion, the bubbles are transported by flow through vessel bifurcations, where they may split prior to eventually reach vessels small enough that they become lodged. This splitting behavior affects the distribution of bubbles and the efficacy of flow occlusion and the treatment. In these studies, we investigated bubble transport in bifurcations using computational and theoretical modeling. The model reproduces the variety of experimentally observed splitting behaviors. Splitting homogeneity and maximum shear stress along the vessel walls is predicted over a variety of physical parameters. Maximum shear stresses were found to decrease with increasing Reynolds number. The initial bubble length was found to affect the splitting behavior in the presence of gravitational asymmetry. This work was supported by NIH Grant R01EB006476.

  20. Lunar transportation system

    Science.gov (United States)

    1993-07-01

    The University Space Research Association (USRA) requested the University of Minnesota Spacecraft Design Team to design a lunar transportation infrastructure. This task was a year long design effort culminating in a complete conceptual design and presentation at Johnson Space Center. The mission objective of the design group was to design a system of vehicles to bring a habitation module, cargo, and crew to the lunar surface from LEO and return either or both crew and cargo safely to LEO while emphasizing component commonality, reusability, and cost effectiveness. During the course of the design, the lunar transportation system (LTS) has taken on many forms. The final design of the system is composed of two vehicles, a lunar transfer vehicle (LTV) and a lunar excursion vehicle (LEV). The LTV serves as an efficient orbital transfer vehicle between the earth and the moon while the LEV carries crew and cargo to the lunar surface. Presented in the report are the mission analysis, systems layout, orbital mechanics, propulsion systems, structural and thermal analysis, and crew systems, avionics, and power systems for this lunar transportation concept.

  1. Transportation Statistics Annual Report, 2017

    Science.gov (United States)

    2018-01-01

    The Transportation Statistics Annual Report describes the Nations transportation system, the systems performance, its contributions to the economy, and its effects on people and the environment. This 22nd edition of the report is based on infor...

  2. Rural transportation emergency preparedness plans.

    Science.gov (United States)

    2009-07-01

    Improving the emergency preparedness of rural transportation systems is the overall goal of this research. Unique characteristics exist in rural transportation systems including widely dispersed and diverse populations and geographic areas. Exploring...

  3. Globalisation, transport and the environment

    Science.gov (United States)

    2010-01-01

    OECD and the International Transport Forum (ITF) held a GLobal Forum on Transport and Environment in a Globalising World, 10-12 November 2008 in Guadalajara, Mexico. There were around 200 participants from 23 countries at the global forum, representi...

  4. SAFETY PLATFORM OF POLISH TRANSPORT

    Directory of Open Access Journals (Sweden)

    Katarzyna CHRUZIK

    2016-03-01

    Full Text Available Analyzing the level of Polish transport safety culture can be seen that it is now dependent on the culture of safety management within the organization and the requirements and recommendations of law in this field for different modes of transport (air, rail, road, water. Of the four basic types of transport requirements are widely developed in the aviation, rail, and water – the sea. In order to harmonize the requirements for transport safety so it appears advisable to develop a platform for exchange of safety information for different modes of transport, and the development of good practices multimodal offering the possibility of improving Polish transport safety. Described in the publication of the proposal in addition to the alignment platform experience and knowledge in the field of transport safety in all its kinds, it can also be a tool for perfecting new operators of public transport.

  5. North American Transportation Statistics Database

    Data.gov (United States)

    Department of Transportation — Contains tables of data for the United States, Canada, and Mexico. Data tables are divided up into 12 categories, including a country overview, transportation flows,...

  6. Transport of encapsulated nuclear fuels

    International Nuclear Information System (INIS)

    Broman, Ulrika; Dybeck, Peter; Ekendahl, Ann-Mari

    2005-12-01

    The transport system for encapsulated fuel is described, including a preliminary drawing of a transport container. In the report, the encapsulation plant is assumed to be located to Oskarshamn, and the repository to Oskarshamn or Forsmark

  7. Solute carrier transporters: Pharmacogenomics research ...

    African Journals Online (AJOL)

    Aghogho

    2010-12-27

    Dec 27, 2010 ... This paper reviews the solute carrier transporters and highlights the fact that there is much to be learnt from .... transporters, drug targets, effect or proteins and meta- ... basolateral or apical plasma membrane of polarized cells,.

  8. Transportation statistics annual report, 2015

    Science.gov (United States)

    2016-01-01

    The Transportation Statistics Annual Report : describes the Nations transportation system, : the systems performance, its contributions to : the economy, and its effects on people and the : environment. This 20th edition of the report is : base...

  9. Transportation statistics annual report, 2013

    Science.gov (United States)

    2014-01-01

    The Transportation Statistics Annual Report : describes the Nations transportation system, : the systems performance, its contributions to : the economy, and its effects on people and the : environment. This 18th edition of the report is : base...

  10. Diffusion coefficient for anomalous transport

    International Nuclear Information System (INIS)

    1986-01-01

    A report on the progress towards the goal of estimating the diffusion coefficient for anomalous transport is given. The gyrokinetic theory is used to identify different time and length scale inherent to the characteristics of plasmas which exhibit anomalous transport

  11. Defense Programs Transportation Risk Assessment

    International Nuclear Information System (INIS)

    Clauss, D.B.

    1994-01-01

    This paper provides an overview of the methodology used in a probabilistic transportation risk assessment conducted to assess the probabilities and consequences of inadvertent dispersal of radioactive materials arising from severe transportation accidents. The model was developed for the Defense Program Transportation Risk Assessment (DPTRA) study. The analysis incorporates several enhancements relative to previous risk assessments of hazardous materials transportation including newly-developed statistics on the frequencies and severities of tractor semitrailer accidents and detailed route characterization using the 1990 Census data

  12. 'Resilience thinking' in transport planning

    OpenAIRE

    Wang, JYT

    2015-01-01

    Resilience has been discussed in ecology for over forty years. While some aspects of resilience have received attention in transport planning, there is no unified definition of resilience in transportation. To define resilience in transportation, I trace back to the origin of resilience in ecology with a view of revealing the essence of resilience thinking and its relevance to transport planning. Based on the fundamental concepts of engineering resilience and ecological resilience, I define "...

  13. The transport of radioactive waste

    International Nuclear Information System (INIS)

    Appleton, P.R.; Poulter, D.R.

    1989-01-01

    Regulations have been developed to ensure the safe transport of all radioactive materials by all modes (road, rail, sea and air). There are no features of radioactive waste which set it aside from other radioactive materials for transport, and the same regulations control all radioactive material transport. These regulations and their underlying basis are described in this paper, and their application to waste transport is outlined. (author)

  14. Transport infrastructure development in China

    Directory of Open Access Journals (Sweden)

    Bouraima Mouhamed Bayane

    2017-05-01

    Full Text Available This paper reviews the historical configuration process of transportation systems in China and examines the relationship between economic development and transport system at three different levels. The current status of transport infrastructure system development in China is summarized at national and regional level. The investment trends for transport infrastructure in China are also depicted. The keys issues relating to government initiatives are presented.

  15. Nanoscale thermal transport

    Science.gov (United States)

    Cahill, David G.; Ford, Wayne K.; Goodson, Kenneth E.; Mahan, Gerald D.; Majumdar, Arun; Maris, Humphrey J.; Merlin, Roberto; Phillpot, Simon R.

    2003-01-01

    Rapid progress in the synthesis and processing of materials with structure on nanometer length scales has created a demand for greater scientific understanding of thermal transport in nanoscale devices, individual nanostructures, and nanostructured materials. This review emphasizes developments in experiment, theory, and computation that have occurred in the past ten years and summarizes the present status of the field. Interfaces between materials become increasingly important on small length scales. The thermal conductance of many solid-solid interfaces have been studied experimentally but the range of observed interface properties is much smaller than predicted by simple theory. Classical molecular dynamics simulations are emerging as a powerful tool for calculations of thermal conductance and phonon scattering, and may provide for a lively interplay of experiment and theory in the near term. Fundamental issues remain concerning the correct definitions of temperature in nonequilibrium nanoscale systems. Modern Si microelectronics are now firmly in the nanoscale regime—experiments have demonstrated that the close proximity of interfaces and the extremely small volume of heat dissipation strongly modifies thermal transport, thereby aggravating problems of thermal management. Microelectronic devices are too large to yield to atomic-level simulation in the foreseeable future and, therefore, calculations of thermal transport must rely on solutions of the Boltzmann transport equation; microscopic phonon scattering rates needed for predictive models are, even for Si, poorly known. Low-dimensional nanostructures, such as carbon nanotubes, are predicted to have novel transport properties; the first quantitative experiments of the thermal conductivity of nanotubes have recently been achieved using microfabricated measurement systems. Nanoscale porosity decreases the permittivity of amorphous dielectrics but porosity also strongly decreases the thermal conductivity. The

  16. Transportation of irradiated fuel elements

    International Nuclear Information System (INIS)

    1980-01-01

    A critique is presented of current methods of transporting spent nuclear fuel and the inadequacies of the associated contingency plans, with particular reference to the transportation of irradiated fuel through London. Anti-nuclear and pro-nuclear arguments are presented on a number of factors, including tests on flasks, levels of radiation exposure, routine transport arrangements and contingency arrangements. (U.K.)

  17. NWMO transportation technical work program

    International Nuclear Information System (INIS)

    Hatton, C.

    2015-01-01

    This paper describes technical work program for the transportation nuclear waste by the Nuclear Waste Management Organization (NWMO). Transportation work program involves risk assessment which under normal conditions involves dose assessment to the worker and the public as well as consideration of transportation system routing and operations. It also involves possible accident scenarios using forensic modelling and probability analysis.

  18. Improving Hygiene in Food Transportation

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Lukasse, L.J.S.

    2016-01-01

    The hygiene aspect of food transport has become an issue for European transport operators. This development started roughly in 1990, when national governments urged transport operators to act on food safety. However, nowadays retailers and food producers are demanding more hygiene measures from

  19. Lectures on neutron transport theory

    International Nuclear Information System (INIS)

    Benoist, P.

    1986-02-01

    This note is divided in two parts. In the first one the basis of transport theory, that is, the principal forms of the transport equation and the resulting theorems, are presented. The second part is particularly devoted to the applications of integral transport theory to reactor lattice problems [fr

  20. Transport, chaos and plasma physics

    International Nuclear Information System (INIS)

    Benkadda, S.; Doveil, F.; Elskens, Y.

    1993-01-01

    This workshop made it possible to gather for the first time plasma physicists, dynamical systems physicists and mathematicians, around a general theme focusing on the characterisation of chaotic transport. The participations have been divided into 4 topics: - dynamical systems and microscopic models of chaotic transport, - magnetic fluctuations and transport in tokamaks, - drift wave turbulence, self-organisation and intermittency, and - Wave-particle interactions

  1. Transport studies for ignition experiments

    International Nuclear Information System (INIS)

    Nocentini, A.; Schultz, G.

    1990-07-01

    The results of a predictive study of plasma energy confinement in IGNITOR, performed with a 1 1/2-D transport code and the Tang an Redi transport model, are reported. For comparison, performance predictions for NET adopting similar assumptions on plasma transport are also presented. (author) 16 figs., 5 tabs., 13 refs

  2. NWMO transportation technical work program

    Energy Technology Data Exchange (ETDEWEB)

    Hatton, C. [Nuclear Waste Management Organization, Toronto, ON (Canada)

    2015-07-01

    This paper describes technical work program for the transportation nuclear waste by the Nuclear Waste Management Organization (NWMO). Transportation work program involves risk assessment which under normal conditions involves dose assessment to the worker and the public as well as consideration of transportation system routing and operations. It also involves possible accident scenarios using forensic modelling and probability analysis.

  3. Transportation Brokerage: An Instructional Module.

    Science.gov (United States)

    Hayden, Linda

    A concept-based introduction to transportation brokerage is provided in this instructional module for undergraduate and graduate transportation-related courses for disciplines such as engineering, business, marketing, and technology. The concept of transportation brokerage is defined as an assignment of the management of a specific element of a…

  4. Saturated Zone Colloid Transport

    Energy Technology Data Exchange (ETDEWEB)

    H. S. Viswanathan

    2004-10-07

    This scientific analysis provides retardation factors for colloids transporting in the saturated zone (SZ) and the unsaturated zone (UZ). These retardation factors represent the reversible chemical and physical filtration of colloids in the SZ. The value of the colloid retardation factor, R{sub col} is dependent on several factors, such as colloid size, colloid type, and geochemical conditions (e.g., pH, Eh, and ionic strength). These factors are folded into the distributions of R{sub col} that have been developed from field and experimental data collected under varying geochemical conditions with different colloid types and sizes. Attachment rate constants, k{sub att}, and detachment rate constants, k{sub det}, of colloids to the fracture surface have been measured for the fractured volcanics, and separate R{sub col} uncertainty distributions have been developed for attachment and detachment to clastic material and mineral grains in the alluvium. Radionuclides such as plutonium and americium sorb mostly (90 to 99 percent) irreversibly to colloids (BSC 2004 [DIRS 170025], Section 6.3.3.2). The colloid retardation factors developed in this analysis are needed to simulate the transport of radionuclides that are irreversibly sorbed onto colloids; this transport is discussed in the model report ''Site-Scale Saturated Zone Transport'' (BSC 2004 [DIRS 170036]). Although it is not exclusive to any particular radionuclide release scenario, this scientific analysis especially addresses those scenarios pertaining to evidence from waste-degradation experiments, which indicate that plutonium and americium may be irreversibly attached to colloids for the time scales of interest. A section of this report will also discuss the validity of using microspheres as analogs to colloids in some of the lab and field experiments used to obtain the colloid retardation factors. In addition, a small fraction of colloids travels with the groundwater without any significant

  5. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Troy Reed; Ergun Kuru

    2004-09-30

    The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

  6. The transportation institutional plan: Cooperative planning for NWPA transportation

    International Nuclear Information System (INIS)

    Denny, S.H.; Livingston-Behan, E.A.

    1987-01-01

    The Transportation Institutional Plan, published in 1986 by the U.S. Department of Energy's Office of Civilian Radioactive Waste Management (OCRWM), defines a process for effective interaction among those who may be affected by transportation activities conducted under provisions of the Nuclear Waste Policy Act of 1982 (NWPA). The Plan describes formal mechanisms for identifying, addressing, and resolving specific transportation issues. An appendix to the Plan includes detailed discussion of the following transportation issues: (1) the transportation of defense waste; (2) prenotification; (3) physical and rail shipments; (4) highway routing; (5) rail routing; (6) inspection and enforcement for highway and rail shipments; (7) emergency response; (8) liability coverage for transportation to NWPA facilities; (9) cask design and testing; (10) overweight truck shipments; (11) rail service analysis; (12) mixture of transportation modes; (13) transportation infrastructure improvements; (14) OCRWM training standards; (15) transportation operational procedures; and (16) State, Tribal, and local regulation of transportation. The OCRWM's intent is to provide an open accounting of planning, to identify opportunities for public involvement in program activities, and to foster communication and negotiation in the cooperative development of a safe, efficient, and cost-effective NWPA transportation program

  7. The transport forecast - an important stage of transport management

    Science.gov (United States)

    Dragu, Vasile; Dinu, Oana; Oprea, Cristina; Alina Roman, Eugenia

    2017-10-01

    The transport system is a powerful system with varying loads in operation coming from changes in freight and passenger traffic in different time periods. The variations are due to the specific conditions of organization and development of socio-economic activities. The causes of varying loads can be included in three groups: economic, technical and organizational. The assessing of transport demand variability leads to proper forecast and development of the transport system, knowing that the market price is determined on equilibrium between supply and demand. The reduction of transport demand variability through different technical solutions, organizational, administrative, legislative leads to an increase in the efficiency and effectiveness of transport. The paper presents a new way of assessing the future needs of transport through dynamic series. Both researchers and practitioners in transport planning can benefit from the research results. This paper aims to analyze in an original approach how a good transport forecast can lead to a better management in transport, with significant effects on transport demand full meeting in quality terms. The case study shows how dynamic series of statistics can be used to identify the size of future demand addressed to the transport system.

  8. Products - transport - storage; Produits - transports - stockages

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2005-04-15

    9 articles are gathered in this data-sheet; they deal with LPG products, transport and storage. Blackmer offers a full line of LPG equipment for the transfer of propane, butane and anhydrous ammonia. Clesse Industries and Gas Equipment Company equip luxury hotels in Dubai and Abu Dhabi. Since 1975 the company FAS Flussiggas-Anlagen Gmbh, Salzgitter - Germany is one of the leading manufacturers of LPG equipment and components for mobile and stationary bulk plants in Europe. The main products are dispensers, pumps, Auto-gas filling stations, vaporizers, loading arms, electronic cylinder filling scales, flanged valves and safety equipment. FAS is certified with 2 process orientated management systems according to DIN EN ISO 9001:2000 and to PED - Module H1 - Category IV. The company supplies all products and services according to the Pressure Equipment Directive 97/23/EC with CE-mark as well according to regulations ATEX, OIML, TUV, PTB... ECII Engineered Controls International/Rego USA is well known as a worldwide leader and designer/manufacturer of LPG and anhydrous ammonia equipment. The 10. of January Per Sture Jenssen retired from Ragasco A.S. Managing Director after 6 years in the company. Oyvind Hamre who has taken over from Mr. Jenssen, is 39 years of age and he has been 10 years with Ragasco, most recently as R and D Manager. Per Sture Jenssen will still be present in the company until summer 2005 to support during the transition. Corken has put in the market two new products: a new valve and a new pump. Impco Technologies announces completion of BRC acquisition. VOC reduction is a common discussion issue in almost all sectors of the oil business and beyond. Each industry sector has a different strategy towards this issue according to its perceived impact on the business. Although largely motivated by the need to satisfy national and international emission standards, the move towards reduction has encouraged equipment manufacturers to develop advanced

  9. Impact of public transportation market share and other transportation and environmental policy variables on sustainable transportation.

    Science.gov (United States)

    2015-01-01

    Policies that encourage reduced travel, such as traveling shorter distances, and increased use of more efficient transportation modes, such as public transportation and high-occupancy private automobiles, are often considered one of several possible ...

  10. Transportation Options | Climate Neutral Research Campuses | NREL

    Science.gov (United States)

    Transportation Options Transportation Options Transportation to, from, and within a research campus from business travel often enlarge the footprint more than expected. To understand options for climate

  11. Environmental Baseline File National Transportation

    International Nuclear Information System (INIS)

    Harris, M.

    1999-01-01

    This Environmental Baseline File summarizes and consolidates information related to the national-level transportation of commercial spent nuclear fuel. Topics addressed include: shipments of commercial spent nuclear fuel based on mostly truck and mostly rail shipping scenarios; transportation routing for commercial spent nuclear fuel sites and DOE sites; radionuclide inventories for various shipping container capacities; transportation routing; populations along transportation routes; urbanized area population densities; the impacts of historical, reasonably foreseeable, and general transportation; state-level food transfer factors; Federal Guidance Report No. 11 and 12 radionuclide dose conversion factors; and national average atmospheric conditions

  12. Sustainable Transport and Performance Indicators

    DEFF Research Database (Denmark)

    Gudmundsson, Henrik

    2004-01-01

    Sustainable transport has become a major policy concern in recent years. The term suggests a need to consider transport in a comprehensive perspective including the well-being of both present and future generations, and taking environmental, social and economic issues into account. Indicators...... in forecasting and tracking the performance of transport systems increasingly guide sustainable transport policy making. This review explores the implications of the sustainable transport” concept and how it can be made operational with indicators. A number of indicator systems are reviewed, and some strengths...

  13. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

    2003-09-30

    The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

  14. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Neelima Godugu

    2000-07-30

    ACTS flow loop is now operational under elevated pressure and temperature. Currently, experiments with synthetic based drilling fluids under pressure and temperature are being conducted. Based on the analysis of Fann 70 data, empirical correlations defining the shear stress as a function of temperature, pressure and the shear rate have been developed for Petrobras synthetic drilling fluids. PVT equipment has been modified for testing Synthetic oil base drilling fluids. PVT tests with Petrobras Synthetic base mud have been conducted and results are being analyzed Foam flow experiments have been conducted and the analysis of the data has been carried out to characterize the rheology of the foam. Comparison of pressure loss prediction from the available foam hydraulic models and the test results has been made. Cuttings transport experiments in horizontal annulus section have been conducted using air, water and cuttings. Currently, cuttings transport tests in inclined test section are being conducted. Foam PVT analysis tests have been conducted. Foam stability experiments have also been conducted. Effects of salt and oil concentration on the foam stability have been investigated. Design of ACTS flow loop modification for foam and aerated mud flow has been completed. A flow loop operation procedure for conducting foam flow experiments under EPET conditions has been prepared Design of the lab-scale flow loop for dynamic foam characterization and cuttings monitoring instrumentation tests has been completed. The construction of the test loop is underway. As part of the technology transport efforts, Advisory Board Meeting with ACTS-JIP industry members has been organized on May 13, 2000.

  15. Transport of radioactive materials

    International Nuclear Information System (INIS)

    Huck, W.

    1992-01-01

    The book presents a systematic survey of the legal provisions governing the transport of radioactive materials, placing emphasis on the nuclear licensing provisions of sections 4, 4b of the Atomic Energy, Act (AtG) and sections 8-10 of the Radiation Protection Ordinance (StrlSchV), also considering the provisions of the traffic law governing the carriage of hazardous goods. The author's goal is to establish a systematic basis by comparative analysis of the licensing regulations under atomic energy law, for the purpose of formulating a proposed amendment to the law, for the sake of clarity. The author furthermore looks for and develops criteria that can be of help in distinguishing the regulations governing the carriage of hazardous goods from the nuclear regulatory provisions. He also examines whether such a differentiation is detectable, particularly in those amendments to the StrlSchV which came after the Act on Carriage of Hazardous Goods. The regulations governing the transport of radioactive materials under the AtG meet with the problem of different classification systems being applied, to radioactive materials in the supervisory regulations on the one hand, and to nuclear materials in Annex 1 to the AtG on the other hand. A classification of natural, non-nuclear grade uranium e.g. by the financial security provisions is difficult as a result of these differences in the laws. The author shows that the transport regulations of the StrlSchV represent an isolated supervisory instrument that has no connecting factor to the sections 28 ff StrlSchV, as radiation protection is provided for by the regulations of the Act on Carriage of Hazardous Goods. The author suggests an amendment of existing law incorporating the legal intent of sections 8-10 StrlSchV and of sections 4, 4b AtG into two sections, and abolishing the supervisory provisions of the StrlSchV altogether. (orig./HP) [de

  16. The Edge supersonic transport

    Science.gov (United States)

    Agosta, Roxana; Bilbija, Dushan; Deutsch, Marc; Gallant, David; Rose, Don; Shreve, Gene; Smario, David; Suffredini, Brian

    1992-01-01

    As intercontinental business and tourism volumes continue their rapid expansion, the need to reduce travel times becomes increasingly acute. The Edge Supersonic Transport Aircraft is designed to meet this demand by the year 2015. With a maximum range of 5750 nm, a payload of 294 passengers and a cruising speed of M = 2.4, The Edge will cut current international flight durations in half, while maintaining competitive first class, business class, and economy class comfort levels. Moreover, this transport will render a minimal impact upon the environment, and will meet all Federal Aviation Administration Part 36, Stage III noise requirements. The cornerstone of The Edge's superior flight performance is its aerodynamically efficient, dual-configuration design incorporating variable-geometry wingtips. This arrangement combines the benefits of a high aspect ratio wing at takeoff and low cruising speeds with the high performance of an arrow-wing in supersonic cruise. And while the structural weight concerns relating to swinging wingtips are substantial, The Edge looks to ever-advancing material technologies to further increase its viability. Heeding well the lessons of the past, The Edge design holds economic feasibility as its primary focus. Therefore, in addition to its inherently superior aerodynamic performance, The Edge uses a lightweight, largely windowless configuration, relying on a synthetic vision system for outside viewing by both pilot and passengers. Additionally, a fly-by-light flight control system is incorporated to address aircraft supersonic cruise instability. The Edge will be produced at an estimated volume of 400 aircraft and will be offered to airlines in 2015 at $167 million per transport (1992 dollars).

  17. Pluto's Volatile Transport

    Science.gov (United States)

    Young, Leslie

    2012-10-01

    Pluto's varying subsolar latitude and heliocentric distance leads to large variations in the surface volatile distribution and surface pressure. I present results of new volatile transport models (Young 2012a, b). The models include insolation, thermal emission, subsurface conduction, heating of a volatile slab, internal heat flux, latent heat of sublimation, and strict global mass balance. Numeric advances include initial conditions that allow for rapid convergence, efficient computation with matrix arithmetic, and stable Crank-Nicholson timesteps for both bare and volatile-covered areas. Runs of the model show six distinct seasons on Pluto. (1) As Pluto approaches perihelion, the volatiles on the old winter pole (the Rotational North Pole, RNP) becomes more directly illuminated , and the pressure and albedo rise rapidly. (2) When a new ice cap forms on the Rotational South Pole, RSP, volatiles are exchanged between poles. The pressure and albedo change more slowly. (3) When all volatiles have sublimed from the RNP, the albedo and pressure drop rapidly. (4-6) A similar pattern is repeated near aphelion with a reversal of the roles and the poles. I will compare results with earlier Pluto models of Hansen and Paige (1996), show the dependence on parameters such as substrate inertia, and make predictions for the New Horizons flyby of Pluto in 2015. This work was supported, in part, by funding from NASA Planetary Atmospheres Grant NNG06GF32G and the Spitzer project (JPL research support Agreement 1368573). Hansen, C. J. and D. A. Paige 1996. Seasonal Nitrogen Cycles on Pluto. Icarus 120, 247-265. Young, L. A. 2012a. Volatile transport on inhomogeneous surfaces: I - Analytic expressions, with application to Pluto’s day. Icarus, in press Young, L. A. 2012b. Volatile transport on inhomogeneous surfaces: II. Numerical calculations, with application to Pluto's season. In preparation.

  18. Stochastic models of intracellular transport

    KAUST Repository

    Bressloff, Paul C.

    2013-01-09

    The interior of a living cell is a crowded, heterogenuous, fluctuating environment. Hence, a major challenge in modeling intracellular transport is to analyze stochastic processes within complex environments. Broadly speaking, there are two basic mechanisms for intracellular transport: passive diffusion and motor-driven active transport. Diffusive transport can be formulated in terms of the motion of an overdamped Brownian particle. On the other hand, active transport requires chemical energy, usually in the form of adenosine triphosphate hydrolysis, and can be direction specific, allowing biomolecules to be transported long distances; this is particularly important in neurons due to their complex geometry. In this review a wide range of analytical methods and models of intracellular transport is presented. In the case of diffusive transport, narrow escape problems, diffusion to a small target, confined and single-file diffusion, homogenization theory, and fractional diffusion are considered. In the case of active transport, Brownian ratchets, random walk models, exclusion processes, random intermittent search processes, quasi-steady-state reduction methods, and mean-field approximations are considered. Applications include receptor trafficking, axonal transport, membrane diffusion, nuclear transport, protein-DNA interactions, virus trafficking, and the self-organization of subcellular structures. © 2013 American Physical Society.

  19. Radiation transport in MEDUSA

    International Nuclear Information System (INIS)

    Rose, S.J.; Evans, R.G.

    1983-09-01

    The transport of energy by X-ray photons has been included in the lD Lagrangian hydrodynamics code, MEDUSA. Calculations of the implosion by 0.53 μm laser irradiation of plastic and glass microballoons of current interest at the Central Laser Facility show that radiation preheats the fill gas and alters the temperature and density profiles during the implosion. A lower maximum gas temperature is obtained and this results, for a DT gas fill, in a greatly reduced neutron yield. (author)

  20. Neutralized transport experiment

    International Nuclear Information System (INIS)

    Roy, P.K.; Yu, S.S.; Eylon, S.; Henestroza, E.; Anders, A.; Gilson, E.P.; Bieniosek, F.M.; Greenway, W.G.; Logan, B.G.; Waldron, W.L.; Shuman, D.B.; Vanecek, D.L.; Welch, D.R.; Rose, D.V.; Thoma, C.; Davidson, R.C.; Efthimion, P.C.; Kaganovich, I.; Sefkow, A.B.; Sharp, W.M.

    2005-01-01

    Experimental details on providing active neutralization of high brightness ion beam have been demonstrated for Heavy Ion Fusion program. A K + beam was extracted from a variable-perveance injector and transported through 2.4 m long quadrupole lattice for final focusing. Neutralization was provided by a localized cathode arc plasma plug and a RF volume plasma system. Effects of beam perveance, emittance, convergence focusing angle, and axial focusing position on neutralization have been investigated. Good agreement has been observed with theory and experiment throughout the study