WorldWideScience

Sample records for electric appliances

  1. Electric emissions from electrical appliances

    International Nuclear Information System (INIS)

    Leitgeb, N.; Cech, R.; Schroettner, J.

    2008-01-01

    Electric emissions from electric appliances are frequently considered negligible, and standards consider electric appliances to comply without testing. By investigating 122 household devices of 63 different categories, it could be shown that emitted electric field levels do not justify general disregard. Electric reference values can be exceeded up to 11-fold. By numerical dosimetry with homogeneous human models, induced intra-corporal electric current densities were determined and factors calculated to elevate reference levels to accounting for reduced induction efficiency of inhomogeneous fields. These factors were found not high enough to allow generally concluding on compliance with basic restrictions without testing. Electric appliances usually simultaneously emit both electric and magnetic fields exposing almost the same body region. Since the sum of induced current densities is limited, one field component reduces the available margin for the other. Therefore, superposition of electric current densities induced by either field would merit consideration. (authors)

  2. Electrical field of electrical appliances versus distance: A preliminary analysis

    International Nuclear Information System (INIS)

    Mustafa, Nur Badariah Ahmad; Nordin, Farah Hani; Ismail, Fakaruddin Ali Ahmad; Alkahtani, Ammar Ahmed; Balasubramaniam, Nagaletchumi; Hock, Goh Chin; Shariff, Z A M

    2013-01-01

    Every household electrical appliance that is plugged in emits electric field even if it is not operating. The source where the appliance is plugged into and the components of household electrical appliance contribute to electric field emission. The electric field may cause unknown disturbance to the environment or also affect the human health and the effect might depends on the strength of the electric field emitted by the appliance. This paper will investigate the strength of the electric field emitted by four different electrical appliances using spectrum analyser. The strength will be captured at three different distances; (i) 1m (ii) 2m and (iii) 3m and analysis of the strength of the electrical field is done based on the three different distances. The measurement results show that the strength of the electric field is strongest when it is captured at 1m and the weakest at 3m from the electrical appliance. The results proved that the farther an object is located from the electrical appliance; the less effect the magnetic field has.

  3. Electrical appliance energy consumption control methods and electrical energy consumption systems

    Science.gov (United States)

    Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

    2006-03-07

    Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

  4. Electrical appliance energy consumption control methods and electrical energy consumption systems

    Science.gov (United States)

    Donnelly, Matthew K [Kennewick, WA; Chassin, David P [Pasco, WA; Dagle, Jeffery E [Richland, WA; Kintner-Meyer, Michael [Richland, WA; Winiarski, David W [Kennewick, WA; Pratt, Robert G [Kennewick, WA; Boberly-Bartis, Anne Marie [Alexandria, VA

    2008-09-02

    Electrical appliance energy consumption control methods and electrical energy consumption systems are described. In one aspect, an electrical appliance energy consumption control method includes providing an electrical appliance coupled with a power distribution system, receiving electrical energy within the appliance from the power distribution system, consuming the received electrical energy using a plurality of loads of the appliance, monitoring electrical energy of the power distribution system, and adjusting an amount of consumption of the received electrical energy via one of the loads of the appliance from an initial level of consumption to an other level of consumption different than the initial level of consumption responsive to the monitoring.

  5. Decision-making in electrical appliance use in the home

    International Nuclear Information System (INIS)

    Yamamoto, Yoshihiro; Suzuki, Akihiko; Fuwa, Yasuhiro; Sato, Tomohiro

    2008-01-01

    This paper presents the results of a survey as well as an argument from the viewpoint of behavioral economics with the aim of clarifying how consumers make decisions about electrical appliance use in the home. A survey of consumers showed that most have little awareness of the energy efficiency of appliances, the price of the services produced by electrical appliances, or electricity rates. These findings indicate that price does not function as a signal in electricity consumption through electrical appliance use. Rather, we found that consumer decision-making in electricity consumption is dependent on the characteristics of the particular electrical appliances they use. Additionally, we argue that the payment system for home electricity consumption plays an important role in decision-making, causing biases due to aspects of human psychology discussed here in terms of satisficing and heuristics, payment decoupling, and budgeting. We conclude that decision-making about electrical appliance use and electricity consumption in the home is not always rational and is affected both by the particular characteristics of appliances and the payment system for electricity consumption along with human psychology

  6. Characterization of electrical appliances in transient state

    Science.gov (United States)

    Wójcik, Augustyn; Winiecki, Wiesław

    2017-08-01

    The article contains the study about electrical appliance characterization on the basis of power grid signals. To represent devices, parameters of current and voltage signals recorded during transient states are used. In this paper only transients occurring as a result of switching on devices are considered. The way of data acquisition performed in specialized measurement setup developed for electricity load monitoring is described. The paper presents the method of transients detection and the method of appliance parameters calculation. Using the set of acquired measurement data and appropriate software the set of parameters for several household appliances operating in different operating conditions was processed. Usefulness of appliances characterization in Non-Intrusive Appliance Load Monitoring System (NIALMS) with the use of proposed method is discussed focusing on obtained results.

  7. Magnetic fields from electric toothbrushes promote corrosion in orthodontic stainless steel appliances but not in titanium appliances.

    Science.gov (United States)

    Kameda, Takashi; Ohkuma, Kazuo; Oda, Hirotake; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

    2013-01-01

    Electric toothbrushes are widely used, and their electric motors have been reported to produce low-frequency electromagnetic fields that induced electric currents in metallic objects worn by the users. In this study, we showed that electric toothbrushes generated low-frequency magnetic fields (MFs) and induced electric currents in orthodontic appliances in artificial saliva (AS), which accelerated corrosion in stainless steel (SUS) appliances, but not in titanium (Ti) appliances; the corrosion was evaluated by using an inductively coupled plasma-optical emission spectrometer and a three-dimensional laser confocal microscope. The pH of AS used for appliance immersion did not change during or after MF exposure. These results suggested that MF-induced currents from electric toothbrushes could erode SUS appliances, but not Ti appliances, because of their high corrosion potentials. Further studies are required to clarify the mechanisms of metallic corrosion by induced currents in dental fields, which may trigger metal allergies in patients.

  8. Leaking electricity in domestic appliances

    International Nuclear Information System (INIS)

    Meier, Alan; Rosen, Karen

    1999-01-01

    Many types of home electronic equipment draw electric power when switched off or not performing their principal functions. Standby power use (or ''leaking electricity'') for most appliances ranges from 1 - 20 watts. Even though standby use of each device is small, the combined standby power use of all appliances in a home can easily exceed 50 watts. Leaking electricity is already responsible for 5 to 10 percent of residential electricity use in the United States and over 10 percent in Japan. An increasing number of white goods also have standby power requirements. There is a growing international effort to limit standby power to around one watt per device. New and existing technologies are available to meet this target at little or no extra cost

  9. 14 CFR 25.1365 - Electrical appliances, motors, and transformers.

    Science.gov (United States)

    2010-01-01

    ... Equipment § 25.1365 Electrical appliances, motors, and transformers. (a) Domestic appliances must be... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Electrical appliances, motors, and transformers. 25.1365 Section 25.1365 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF...

  10. Electric household appliances lighting. Synthesis; Electromenager eclairage. Note de synthese

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    This study has been realized on 10000 families in order to know the French behavior concerning the electric household appliances and the lighting of their accommodation. The document presents statistically the answers to the questions on the electric household in the accommodation, the choice criteria, the use conditions, the washing temperatures, the nature of the electric household appliances, the microwave ovens, the influence of the energy-label on the appliances and the lighting. (A.L.B.)

  11. Ubiquitous monitoring of electrical household appliances.

    Science.gov (United States)

    Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

    2012-11-07

    The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

  12. Ubiquitous Monitoring of Electrical Household Appliances

    Science.gov (United States)

    Lloret, Jaime; Macías, Elsa; Suárez, Alvaro; Lacuesta, Raquel

    2012-01-01

    The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home). The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g) and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper. PMID:23202205

  13. Ubiquitous Monitoring of Electrical Household Appliances 

    Directory of Open Access Journals (Sweden)

    Raquel Lacuesta

    2012-11-01

    Full Text Available The number of appliances at home is increasing continuously, mainly because they make our lives easier. Currently, technology is integrated in all objects of our daily life. TCP/IP let us monitor our home in real time and check ubiquitously if something is happening at home. Bearing in mind this idea, we have developed a low-cost system, which can be used in any type of electrical household appliance that takes information from the appliance and posts the information to the Twitter Social network. Several sensors placed in the household appliances gather the sensed data and send them wired or wirelessly, depending on the case, using small and cheap devices to a gateway located in the home. This gateway takes decisions, based on the received data, and sends notifications to Twitter. We have developed a software application that takes the values and decides when to issue an alarm to the registered users (Twitter friends of our smart home. The performance of our system has been measured taking into account the home network (using IEEE 802.3u and IEEE 802.11g and the data publishing in Twitter. As a result, we have generated an original product and service for any electrical household appliance, regardless of the model and manufacturer, that helps home users improve their quality of life. The paper also shows that there is no system with the same innovative features like the ones presented in this paper.

  14. Reducing Electricity Demand Peaks by Scheduling Home Appliances Usage

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

    2011-01-01

    Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users’ appliances...... should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power...... consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions...

  15. Optimal joint scheduling of electrical and thermal appliances in a smart home environment

    International Nuclear Information System (INIS)

    Shirazi, Elham; Zakariazadeh, Alireza; Jadid, Shahram

    2015-01-01

    Highlights: • Thermal appliances are scheduled based on desired temperature and energy prices. • A discomfort index has been introduced within the home energy scheduling model. • Appliances are scheduled based on activity probability and desired options. • Starting probability depends on the social random factor and consumption behavior. - Abstract: With the development of home area network, residents have the opportunity to schedule their power usage in the home by themselves aiming at reducing electricity expenses. Moreover, as renewable energy sources are deployed in home, a home energy management system needs to consider both energy consumption and generation simultaneously to minimize the energy cost. In this paper, a smart home energy management model has been presented in which electrical and thermal appliances are jointly scheduled. The proposed method aims at minimizing the electricity cost of a residential customer by scheduling various type of appliances considering the residents consumption behavior, seasonal probability, social random factor, discomfort index and appliances starting probability functions. In this model, the home central controller receives the electricity price information, environmental factors data as well as the resident desired options in order to optimally schedule appliances including electrical and thermal. The scheduling approach is tested on a typical home including variety of home appliances, a small wind turbine, photovoltaic panel, combined heat and power unit, boiler and electrical and thermal storages over a 24-h period. The results show that the scheduling of different appliances can be reached simultaneously by using the proposed formulation. Moreover, simulation results evidenced that the proposed home energy management model exhibits a lower cost and, therefore, is more economical.

  16. Reducing electricity demand peaks by scheduling home appliances usage

    Energy Technology Data Exchange (ETDEWEB)

    Rossello-Busquet, A.; Kardaras, G.; Baek Iversen, V.; Soler, J.; Dittmann, L.

    2011-05-15

    Nowadays there is a tendency to consume electricity during the same period of the day leading to demand peaks. Regular energy consumption habits lead to demand peaks at specific temporal intervals, because users consume power at the same time. In order to avoid demand peaks, users' appliances should consume electricity in a more temporarily distributed way. A new methodology to schedule the usage of home appliances is proposed and analyzed in this paper. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption limit, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where the electrical devices are classified in low and high priority groups. The high priority devices are always granted power in order to operate without temporal restrictions. On the contrary, the low priority devices have to pause their operation, when the algorithm dictates it, and resume it in the future. This can become beneficial for both energy companies and users. The electricity suppliers companies will be capable of regulating power generation during demand peaks periods. Moreover, users can be granted lower electricity bill rates for accepting delaying the operation of some of their appliances. In order to analyze this scenario, teletraffic engineering theory, which is used in evaluating the performance of telecommunication networks, is used. A reversible fair scheduling (RFS) algorithm, which was originally developed for telecommunication networks, is applied. The purpose is to analyze how a power consumption limit and priorities for home appliances will affect the demand peak and the users' everyday life. Verification of the effectiveness of the RFS algorithm is done by means of simulation and by using real data for power consumption and operation hours. The defined maximum power limit of 750 and 1000 Watt was not exceeded during

  17. Measures for improving the adoption of higher efficiency appliances in Indonesian households: An analysis of lifetime use and decision-making in the purchase of electrical appliances

    International Nuclear Information System (INIS)

    Wijaya, Muhammad Ery; Tezuka, Tetsuo

    2013-01-01

    Highlights: ► We observe human psychosocial variables regarding purchase of electrical appliances. ► Two cities with different cultures are subject of this study – Bandung and Yogyakarta. ► Differences in the lifetime of appliances can be attributed to the cultural. ► Ads and store’s staff have the greatest impact on people’s choice of appliances. ► Adoption of higher-efficiency appliances could be implemented based on each culture. - Abstract: One approach to decreasing electricity consumption is to facilitate the replacement of older appliances with new, higher-efficiency. The objectives of this paper are to compare and analyse the replacement of appliances in two cities of Indonesia – Yogyakarta and Bandung – that are characterised by different cultural backgrounds, ethnicities, and decision-making processes in the household purchase of electrical appliances. A questionnaire survey method was employed to obtain information on behavioural economics and human psychosocial variables such as attitudes, beliefs and perceived benefits regarding the replacement and purchase of electrical appliances. The results show that refrigerators in Yogyakarta have a longer lifetime than in Bandung. However, in Bandung, air conditioners, electric fans, rice cookers, and water pumps have a longer lifetime than in Yogyakarta. These differences in the lifetime of appliances can be attributed to the cultural differences within the two cities that are reflected in the manner in which people use electrical appliances as well as to their lack of knowledge regarding appliance operation. An analysis of the factors influencing the purchase of appliances indicated that people in Yogyakarta show a greater awareness of the benefits of adopting higher-efficiency appliances than do persons in Bandung. The following suggestions could be implemented to improve the strategy of encouraging the adoption of higher-efficiency appliances: (1) in Yogyakarta, energy labelling could be

  18. Appliances facilitating everyday life - electricity use derived from daily activities

    Energy Technology Data Exchange (ETDEWEB)

    Ellegaard, Kajsa (Dept of Thematic Studies, Linkoeping Univ. (Sweden)), e-mail: kajsa.ellegard@liu.se; Widen, Joakim (Dept of Engineering Sciences, Uppsala Univ. (Sweden)); Vrotsou, Katerina (Dept of Science and Technology, Linkoeping Univ. (Sweden))

    2011-06-15

    The purpose of this paper is to present how, using a visualization method, electricity use can be derived from the everyday activity patterns of household members. Target groups are, on the one hand, professionals in the energy sector and energy advisors who need more knowledge about household energy use, and, on the other hand, household members wanting to reduce the energy use by revealing their own habits and thereby finding out how changed activity performance may influence electricity use. The focus is on the relation between utilizing electric appliances to perform everyday life activities and the use of electricity. The visualization method is based on the time-geographic approach developed by Haegerstrand and includes a model that estimates appliance electricity use from household members' activities. Focus, in this paper, is put on some basic activities performed to satisfy daily life needs: cooking and use of information, communication and entertainment devices. These activities appear frequently in the everyday life of households, even though not all household members perform them all. The method is applied on a data material comprising time-diaries written by 463 individuals (aged 10 to 85+) in 179 households in different parts of Sweden. The visualization method reveals when and for how long activities that claim electric appliances are performed by which individual(s). It also shows electricity load curves generated from the use of appliances at different levels, such as individual, household and group or population levels. At household level the method can reveal which household members are the main users of electricity, i.e. the division of labour between household members. Thereby it also informs about whom could be approached by energy companies and energy advisors in information campaigns. The main result of the study is that systematic differences in activity patterns in subgroups of a population can be identified (e.g. men and women) but

  19. Educational Electrical Appliance Power Meter and Logger

    Science.gov (United States)

    Nunn, John

    2013-01-01

    The principles behind two different designs of inductive power meter are presented. They both make use of the microphone input of a computer which, together with a custom-written program, can record the instantaneous power of a domestic electrical appliance. The device can be built quickly and can be calibrated with reference to a known power…

  20. 46 CFR 111.77-3 - Appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances. 111.77-3 Section 111.77-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Appliances and Appliance Circuits § 111.77-3 Appliances. All electrical appliances, including, but...

  1. CE APPROVAL IN ELECTRICAL HOUSEHOLD APPLIANCES AND A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Nazmi EKREN

    2009-01-01

    Full Text Available Due to the reason for rapidly developing technology, increasing competition medium, and awareness of the consumers, nowadays, the exigency of production with good quality has gained more and more significance. Certification of the quality and safety of the products to the consumers is compulsory in terms of producers. There are some documents to certify safety of the products. One of them is CE certificate. In this paper, basic information about CE mark is given and CE standards and tests required for electrical household appliances are mentioned. As an application, one of an electrical household appliance, toaster grill is treated and examined. To obtain CE certificate for toaster grill, required tests are made according to EN60335-2-9 and CE certificate is obtained.

  2. The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes.

    Science.gov (United States)

    Kelly, Jack; Knottenbelt, William

    2015-01-01

    Many countries are rolling out smart electricity meters. These measure a home's total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the 'ground truth' demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

  3. Energy Efficiency of Electrical Appliances - Effects of Instruments and Measures; Energieeffizienz bei Elektrogeraeten

    Energy Technology Data Exchange (ETDEWEB)

    Brunner, C.U.; Bush, E.; Gasser, S.; Lingenhel, S.; Nipkow, J.

    2001-07-01

    This comprehensive report for the Swiss Federal Office of Energy presents the results of an analysis made of the market for electrical appliances in Switzerland with the aim of understanding the instruments and measures needed to improve energy efficiency better. The paper reports on reviews made of previous studies that were made in Switzerland and Germany and on interviews made with important persons and institutions in this field. Eight basic findings are listed concerning market expansion, technical progress, user behaviour, efficiency, possibilities for intervention, market forces, efficient appliances as a niche market and the competence lacking in the energy-efficiency area. Twelve basic points to be considered in the implementation of an energy-efficiency strategy are discussed and a list of requirements to be fulfilled by politics is presented. The results of the analysis for various sectors and the recommendations made for an implementation organisation are presented in detail. The report is concluded with a extract from the data base on the energy consumption of electrical appliances.

  4. The UK-DALE dataset, domestic appliance-level electricity demand and whole-house demand from five UK homes

    Science.gov (United States)

    Kelly, Jack; Knottenbelt, William

    2015-03-01

    Many countries are rolling out smart electricity meters. These measure a home’s total power demand. However, research into consumer behaviour suggests that consumers are best able to improve their energy efficiency when provided with itemised, appliance-by-appliance consumption information. Energy disaggregation is a computational technique for estimating appliance-by-appliance energy consumption from a whole-house meter signal. To conduct research on disaggregation algorithms, researchers require data describing not just the aggregate demand per building but also the ‘ground truth’ demand of individual appliances. In this context, we present UK-DALE: an open-access dataset from the UK recording Domestic Appliance-Level Electricity at a sample rate of 16 kHz for the whole-house and at 1/6 Hz for individual appliances. This is the first open access UK dataset at this temporal resolution. We recorded from five houses, one of which was recorded for 655 days, the longest duration we are aware of for any energy dataset at this sample rate. We also describe the low-cost, open-source, wireless system we built for collecting our dataset.

  5. Regulating electricity demand peaks for home appliances using reversible fair scheduling

    DEFF Research Database (Denmark)

    Kardaras, Georgios; Rossello Busquet, Ana; Iversen, Villy Bæk

    2010-01-01

    This paper describes a novel methodology for regulating electricity demand peaks for home appliances. To achieve this objective, we will make use of the reversible fair scheduling algorithm originally developed for telecommunication networks. The main concept behind this approach is the aggregati...

  6. 78 FR 28190 - Authorization of Production Activity; Foreign-Trade Subzone 29C; GE Appliances (Electric Water...

    Science.gov (United States)

    2013-05-14

    ... DEPARTMENT OF COMMERCE Foreign-Trade Zones Board [B-7-2013] Authorization of Production Activity; Foreign-Trade Subzone 29C; GE Appliances (Electric Water Heaters); Louisville, Kentucky On January 7, 2013, GE Appliances, operator of Subzone 29C in Louisville, Kentucky, submitted a notification of proposed...

  7. “Surprise Gift” Purchases of Small Electric Appliances: A Pilot Study

    NARCIS (Netherlands)

    J. Vanhamme (Joëlle); C.J.P.M. de Bont (Cees)

    2005-01-01

    textabstractUnderstanding decision-making processes for gifts is of strategic importance for companies selling small electrical appliances as gifts account for a large part of their sales. Among all gifts, the ones that are surprising are the most valued by recipients. However, research about

  8. Investigation of the economic possibilities regarding the reduction of energy intensity for electrical household appliances. Vol. 1

    Energy Technology Data Exchange (ETDEWEB)

    Orth, G

    1980-01-01

    Investigation results concerning the analysis of the energy application for electrical household appliances have not been available up to now. The investigation had the purpose of analysing the energy consumption of energy-intensive household appliances so that energy conservation possibilities with regard to the effectiveness may be developed. The parts of the effective and of the lost energy are being experimentally determined for the following appliances: large-scale hot water tank, washing machine, laundry drier, dish washer, electric hearth, coolers and refrigerators. The influence of the utilization habits on the specific energy consumption and the relationship between the energy application and the application properties are being investigated. On the basis of the investigation results the different possibilities of energy conservation are shown, together with some aspects of economical operation. On the basis of the investigation results also, the potential of the energy conservation, related to practical consumption values, is estimated at about 5-40%, depending on the appliance.

  9. Recycling of electric appliances. Utilization of the new EU regulation; Recycling von Elektrogeraeten. Nutzen der neuen EU-Richtlinie

    Energy Technology Data Exchange (ETDEWEB)

    Friege, Henning [Awista GmbH, Duesseldorf (Germany)

    2012-10-15

    In the light of a shortage of resources the recycling of secondary raw materials and especially of metals from electric appliances is increasingly gaining importance. If one is to believe the announcements, everything is regulated in the best way. But when one considers closer the data from the recycling of resources and especially the non-ferric (NF) metals from electric and electronic appliances, this still is not a success story - we ought to write it.

  10. Estimation of Operating Condition of Appliances Using Circuit Current Data on Electric Distribution Boards

    Science.gov (United States)

    Iwafune, Yumiko; Ogimoto, Kazuhiko; Yagita, Yoshie

    The Energy management systems (EMS) on demand sides are expected as a method to enhance the capability of supply and demand balancing of a power system under the anticipated penetration of renewable energy generation such as Photovoltaics (PV). Elucidation of energy consumption structure in a building is one of important elements for realization of EMS and contributes to the extraction of potential energy saving. In this paper, we propose the estimation method of operating condition of household appliances using circuit current data on an electric distribution board. Circuit current data are broken down by their shape using a self-organization map method and aggregated by appliance based on customers' information of appliance possessed. Proposed method is verified using residential energy consumption measurement survey data.

  11. 24 CFR 3280.807 - Fixtures and appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Fixtures and appliances. 3280.807... Fixtures and appliances. (a) Electrical materials, devices, appliances, fittings, and other equipment... fasten appliances when the manufactured home is in transit. (See § 3280.809.) (b) Specifically listed...

  12. Scheduling home appliances for energy efficient buildings

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana; Kardaras, Georgios; Iversen, Villy Bæk

    2010-01-01

    The number of appliances found in users’ homes is increasing together with electricity consumption of users’ residences. In addition, there is a tendency to consume during the same period leading to demand peaks. During these periods, electricity providers are forced to develop costly methods...... to generate enough power to meet consumers’ requirements. In addition, high demand peaks can lead to electricity shortages or even blackouts in certain areas. In order to avoid demand peaks, users’ appliances should consume electricity in a more distributed way. A new methodology to schedule the usage of home...... appliances is proposed and analyzed. The main concept behind this approach is the aggregation of home appliances into priority classes and the definition of a maximum power consumption threshold, which is not allowed to be exceeded during peak hours. The scenario simulated describes a modern household, where...

  13. Implementing peak load reduction algorithms for household electrical appliances

    International Nuclear Information System (INIS)

    Dlamini, Ndumiso G.; Cromieres, Fabien

    2012-01-01

    Considering household appliance automation for reduction of household peak power demand, this study explored aspects of the interaction between household automation technology and human behaviour. Given a programmable household appliance switching system, and user-reported appliance use times, we simulated the load reduction effectiveness of three types of algorithms, which were applied at both the single household level and across all 30 households. All three algorithms effected significant load reductions, while the least-to-highest potential user inconvenience ranking was: coordinating the timing of frequent intermittent loads (algorithm 2); moving period-of-day time-flexible loads to off-peak times (algorithm 1); and applying short-term time delays to avoid high peaks (algorithm 3) (least accommodating). Peak reduction was facilitated by load interruptibility, time of use flexibility and the willingness of users to forgo impulsive appliance use. We conclude that a general factor determining the ability to shift the load due to a particular appliance is the time-buffering between the service delivered and the power demand of an appliance. Time-buffering can be ‘technologically inherent’, due to human habits, or realised by managing user expectations. There are implications for the design of appliances and home automation systems. - Highlights: ► We explored the interaction between appliance automation and human behaviour. ► There is potential for considerable load shifting of household appliances. ► Load shifting for load reduction is eased with increased time buffering. ► Design, human habits and user expectations all influence time buffering. ► Certain automation and appliance design features can facilitate load shifting.

  14. Securing energy efficiency as a high priority. Scenarios for common appliance electricity consumption in Thailand

    Energy Technology Data Exchange (ETDEWEB)

    Foran, T. [Unit for Social and Environmental Research USER, Faculty of Social Sciences, Chiang Mai University, P.O. Box 144, Chiang Mai, 50200 (Thailand); Du Pont, P.T. [International Resources Group and Joint Graduate School of Energy and Environment, Bangkok (Thailand); Parinya, P. [The Joint Graduate School of Energy and Environment, King Mongkut' s University of Technology Thonburi, Bangkok (Thailand); Phumaraphand, N. [Electricity Generating Authority of Thailand, Nonthaburi (Thailand)

    2010-11-15

    Between 1995 and 2008, Thailand's energy efficiency programs produced an estimated total of 8,369 GWh/year energy savings and 1,471 MW avoided peak power. Despite these impressive saving figures, relatively little future scenario analysis is available to policy makers. Before the 2008 global financial crisis, electricity planners forecasted 5-6% long-term increases in demand. We explored options for efficiency improvements in Thailand's residential sector, which consumes more than 20% of Thailand's total electricity consumption of 150 TWh/year. We constructed baseline and efficient scenarios for the period 2006-2026, for air conditioners, refrigerators, fans, rice cookers, and compact fluorescent light bulbs. We drew on an appliance database maintained by Electricity Generating Authority of Thailand's voluntary labeling program. For the five appliances modeled, the efficiency scenario results in total savings of 12% of baseline consumption after 10 years and 29% of baseline after 20 years. Approximately 80% of savings come from more stringent standards for air conditioners, including phasing out unregulated air conditioner sales within 6 years. Shifting appliance efficiency standards to current best-in-market levels within 6 years produces additional savings. We discuss institutional aspects of energy planning in Thailand that thus far have limited the consideration of energy efficiency as a high-priority resource.

  15. Study of rational energy consumption in electric appliances. An integrated approach; Estudio de racionalizacion del consumo energetico en electrodomesticos. Un enfoque integrador

    Energy Technology Data Exchange (ETDEWEB)

    Massa, Pablo A.; Romero Tirado, Rene R. [La Plata Univ. Nacional (Argentina). Facultad de Ingenieria. Dept. de Electrotecnia

    1997-12-31

    This work presents a global and integrated approach about rational energy consumption concerning the use of electric appliances based on studies carried out in this investigation and information obtained through a joint action of government agents and electric power manufacturers, producers and distributors. It also presents a program named `procaeh`(home electric appliances quality program) in the scope of the communications and energy bureau and energy rational use (URE) management 8 refs., 2 figs., 7 tabs.; e-mail: massa at isis.unlp.edu.ar

  16. PAT portable appliance testing : in-service inspection and testing of electrical equipment

    CERN Document Server

    Scaddan, Brian

    2015-01-01

    The Electricity at Work Regulations 1989 requires any electrical system to be constructed, maintained and used in such a manner as to prevent danger. This means that inspection and testing of systems, including portable appliances, is needed in order to determine if maintenance is required. This book explains in clear language what needs to be done and includes expert advice on legislation as well as actual testing. The book contains an appendix providing the electrical fundamentals needed by non-specialists and also has sample questions (with answers) for the C&G 2377 exam. It is also an ideal revision guide for the non-specialist, such as maintenance staff and caretakers who carry out these tasks part-time, alongside their many other duties.

  17. An Empirical Study of the Factors Influencing Consumer Behaviour in the Electric Appliances Market

    Directory of Open Access Journals (Sweden)

    Małgorzata Łatuszyńska

    2012-08-01

    Full Text Available This study contributes to a deeper understanding of the impact of different factors on consumer buying behaviour. It analyses the relationship between several independent variables, such as cultural, social, personal, psychological and marketing mix factors, and consumer behaviour (as the dependent variable in the electric appliances market. The purpose of this study is to determine the factors affecting consumer preferences and behaviour in the electric appliances market in Iraq. The data employed to analyse the factors influencing consumers’ purchase decision-making processes were obtained through a questionnaire that was conducted in December 2011 in Basra, a city in southern Iraq. The major findings of the study indicated that, overall, the set of independent variables are weakly associated with the dependent variable. However, the in-depth analysis found that social factors, physical factors, and marketing mix elements are strongly associated with consumer buying behaviour. These analyses make it possible to discover consumer decision-making rules. The results may assist producers and retailers in understanding consumer behaviour and improving consumer satisfaction.

  18. Pacific Northwest GridWise™ Testbed Demonstration Projects; Part II. Grid Friendly™ Appliance Project

    Energy Technology Data Exchange (ETDEWEB)

    Hammerstrom, Donald J.; Brous, Jerry; Chassin, David P.; Horst, Gale R.; Kajfasz, Robert; Michie, Preston; Oliver, Terry V.; Carlon, Teresa A.; Eustis, Conrad; Jarvegren, Olof M.; Marek, W.; Munson, Ryan L.; Pratt, Robert G.

    2007-10-01

    Fifty residential electric water heaters and 150 new residential clothes dryers were modified to respond to signals received from underfrequency, load-shedding appliance controllers. Each controller monitored the power-grid voltage signal and requested that electrical load be shed by its appliance whenever electric power-grid frequency fell below 59.95 Hz. The controllers and their appliances were installed and monitored for more than a year at residential sites at three locations in Washington and Oregon. The controllers and their appliances responded reliably to each shallow underfrequency event—an average of one event per day—and shed their loads for the durations of these events. Appliance owners reported that the appliance responses were unnoticed and caused little or no inconvenience for the homes’ occupants.

  19. Cooking Appliances Using High-Frequency Heating

    OpenAIRE

    木村, 秀行; Hideyuki, KIMURA; (株)日立製作所機械研究所

    2007-01-01

    We have produced a guide suitable for people with no technical knowledge of cooking appliances that use high-frequency heating. In general, cooking appliances that use an electric heat source are popular since, they are simple to use because the offer easy heat control, are safe because they do not have naked flames, and do not make kitchens dirty because there is no exhaust. In recent years, high-efficiency cooking appliances using high-frequency heating technology have surged in popularity....

  20. Magnetic emission ranking of electrical appliances. A comprehensive market survey

    International Nuclear Information System (INIS)

    Leitgeb, N.; Cech, R.; Schroettner, J.; Lehofer, P.; Schmidpeter, U.; Rampetsreiter, M.

    2008-01-01

    Over the last decades emissions of magnetic fields from electric appliances have considerably changed. Based on a comprehensive market survey it could be shown that today magnetic emissions are usually characterised by complex frequency spectra while single-frequency emissions have become rare. Therefore, spectral assessment procedures play a critical role. Compared to frequency-weighted equivalent magnetic induction, rms values may underestimate emissions up to two orders of magnitudes. Therefore, rms measurements are not suitable and emission-ranking lists of devices need revision. Surface hot-spot measurements at nominal load conditions and 230 V/50 Hz supply involved 1146 new electrical devices of 166 different categories. High emissions were not rare. Magnetic emissions of devices of 73 different categories exceeded reference levels up to almost two orders of magnitudes above reference levels. Maximum values were higher than reported so far. Magnetic emissions were high enough to make even conformity with existing basic restrictions not self-evident. (authors)

  1. Energy use and appliance ownership in Ireland

    International Nuclear Information System (INIS)

    Leahy, Eimear; Lyons, Sean

    2010-01-01

    This paper examines household energy use and appliance ownership in Ireland. Logit regression analyses on a large micro-dataset reveal how household characteristics can help explain the ownership of energy using appliances. Using OLS regression models, we explore the factors affecting residential energy demand conditional on appliance ownership. Results suggest that the methods of space and water heating employed by a household are even more important than electrical appliances in explaining domestic energy usage. However, the stock of appliances must be included in such models so that results will not be biased. The methods employed in this paper can be easily adopted for studies of household energy use in other countries where household expenditure survey data are available.

  2. BLOND, a building-level office environment dataset of typical electrical appliances

    Science.gov (United States)

    Kriechbaumer, Thomas; Jacobsen, Hans-Arno

    2018-03-01

    Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

  3. BLOND, a building-level office environment dataset of typical electrical appliances.

    Science.gov (United States)

    Kriechbaumer, Thomas; Jacobsen, Hans-Arno

    2018-03-27

    Energy metering has gained popularity as conventional meters are replaced by electronic smart meters that promise energy savings and higher comfort levels for occupants. Achieving these goals requires a deeper understanding of consumption patterns to reduce the energy footprint: load profile forecasting, power disaggregation, appliance identification, startup event detection, etc. Publicly available datasets are used to test, verify, and benchmark possible solutions to these problems. For this purpose, we present the BLOND dataset: continuous energy measurements of a typical office environment at high sampling rates with common appliances and load profiles. We provide voltage and current readings for aggregated circuits and matching fully-labeled ground truth data (individual appliance measurements). The dataset contains 53 appliances (16 classes) in a 3-phase power grid. BLOND-50 contains 213 days of measurements sampled at 50kSps (aggregate) and 6.4kSps (individual appliances). BLOND-250 consists of the same setup: 50 days, 250kSps (aggregate), 50kSps (individual appliances). These are the longest continuous measurements at such high sampling rates and fully-labeled ground truth we are aware of.

  4. Determinants of residential electricity consumption: Using smart meter data to examine the effect of climate, building characteristics, appliance stock, and occupants' behavior

    International Nuclear Information System (INIS)

    Kavousian, Amir; Rajagopal, Ram; Fischer, Martin

    2013-01-01

    We propose a method to examine structural and behavioral determinants of residential electricity consumption, by developing separate models for daily maximum (peak) and minimum (idle) consumption. We apply our method on a data set of 1628 households' electricity consumption. The results show that weather, location and floor area are among the most important determinants of residential electricity consumption. In addition to these variables, number of refrigerators and entertainment devices (e.g., VCRs) are among the most important determinants of daily minimum consumption, while number of occupants and high-consumption appliances such as electric water heaters are the most significant determinants of daily maximum consumption. Installing double-pane windows and energy-efficient lights helped to reduce consumption, as did the energy-conscious use of electric heater. Acknowledging climate change as a motivation to save energy showed correlation with lower electricity consumption. Households with individuals over 55 or between 19 and 35 years old recorded lower electricity consumption, while pet owners showed higher consumption. Contrary to some previous studies, we observed no significant correlation between electricity consumption and income level, home ownership, or building age. Some otherwise energy-efficient features such as energy-efficient appliances, programmable thermostats, and insulation were correlated with slight increase in electricity consumption. - Highlights: • Weather, location and floor area are the most important determinants of residential electricity use. • Daily minimum and maximum are explained by different factors. • Number of refrigerators and entertainment devices explain daily minimum the best. • Number of occupants and high-consumption appliances explain daily maximum the best. • Other factors such as energy efficient features and household's socioeconomic status are examined

  5. Scenarios for Demand Growth of Metals in Electricity Generation Technologies, Cars, and Electronic Appliances.

    Science.gov (United States)

    Deetman, Sebastiaan; Pauliuk, Stefan; van Vuuren, Detlef P; van der Voet, Ester; Tukker, Arnold

    2018-04-17

    This study provides scenarios toward 2050 for the demand of five metals in electricity production, cars, and electronic appliances. The metals considered are copper, tantalum, neodymium, cobalt, and lithium. The study shows how highly technology-specific data on products and material flows can be used in integrated assessment models to assess global resource and metal demand. We use the Shared Socio-economic Pathways as implemented by the IMAGE integrated assessment model as a starting point. This allows us to translate information on the use of electronic appliances, cars, and renewable energy technologies into quantitative data on metal flows, through application of metal content estimates in combination with a dynamic stock model. Results show that total demand for copper, neodymium, and tantalum might increase by a factor of roughly 2 to 3.2, mostly as a result of population and GDP growth. The demand for lithium and cobalt is expected to increase much more, by a factor 10 to more than 20, as a result of future (hybrid) electric car purchases. This means that not just demographics, but also climate policies can strongly increase metal demand. This shows the importance of studying the issues of climate change and resource depletion together, in one modeling framework.

  6. Scenarios for Demand Growth of Metals in Electricity Generation Technologies, Cars, and Electronic Appliances

    Science.gov (United States)

    2018-01-01

    This study provides scenarios toward 2050 for the demand of five metals in electricity production, cars, and electronic appliances. The metals considered are copper, tantalum, neodymium, cobalt, and lithium. The study shows how highly technology-specific data on products and material flows can be used in integrated assessment models to assess global resource and metal demand. We use the Shared Socio-economic Pathways as implemented by the IMAGE integrated assessment model as a starting point. This allows us to translate information on the use of electronic appliances, cars, and renewable energy technologies into quantitative data on metal flows, through application of metal content estimates in combination with a dynamic stock model. Results show that total demand for copper, neodymium, and tantalum might increase by a factor of roughly 2 to 3.2, mostly as a result of population and GDP growth. The demand for lithium and cobalt is expected to increase much more, by a factor 10 to more than 20, as a result of future (hybrid) electric car purchases. This means that not just demographics, but also climate policies can strongly increase metal demand. This shows the importance of studying the issues of climate change and resource depletion together, in one modeling framework. PMID:29533657

  7. How do household characteristics affect appliance usage? Application of conditional demand analysis to Japanese household data

    International Nuclear Information System (INIS)

    Matsumoto, Shigeru

    2016-01-01

    Although both appliance ownership and usage patterns determine residential electricity consumption, it is less known how households actually use their appliances. In this study, we conduct conditional demand analyses to break down total household electricity consumption into a set of demand functions for electricity usage, across 12 appliance categories. We then examine how the socioeconomic characteristics of the households explain their appliance usage. Analysis of micro-level data from the Nation Survey of Family and Expenditure in Japan reveals that the family and income structure of households affect appliance usage. Specifically, we find that the presence of teenagers increases both air conditioner and dishwasher use, labor income and nonlabor income affect microwave usage in different ways, air conditioner usage decreases as the wife's income increases, and microwave usage decreases as the husband's income increases. Furthermore, we find that households use more electricity with new personal computers than old ones; this implies that the replacement of old personal computers increases electricity consumption. - Highlights: •We conduct conditional demand analyses to study household appliance usage. •Micro-level data from the National Survey of Family and Expenditure in Japan are analyzed. •We show how household characteristics determine appliance usage. •High-income households use specific appliances less intensively than low-income households. •The replacement of old TVs and PCs lead to greater electricity consumption.

  8. What can we learn from high-frequency appliance-level energy metering? Results from a field experiment

    International Nuclear Information System (INIS)

    Chen, Victor L.; Delmas, Magali A.; Kaiser, William J.; Locke, Stephen L.

    2015-01-01

    This study uses high-frequency appliance-level electricity consumption data for 124 apartments over 24 months to provide a better understanding of appliance-level electricity consumption behavior. We conduct our analysis in a standardized set of apartments with similar appliances, which allows us to identify behavioral differences in electricity use. The Results show that households' estimations of appliance-level consumption are inaccurate and that they overestimate lighting use by 75% and underestimate plug-load use by 29%. We find that similar households using the same major appliances exhibit substantial variation in appliance-level electricity consumption. For example, households in the 75th percentile of HVAC usage use over four times as much electricity as a user in the 25th percentile. Additionally, we show that behavior accounts for 25–58% of this variation. Lastly, we find that replacing the existing refrigerator with a more energy-efficient model leads to overall energy savings of approximately 11%. This is equivalent to results from behavioral interventions targeting all appliances but might not be as cost effective. Our findings have important implications for behavior-based energy conservation policies. - Highlights: • Hourly electricity usage was collected from 124 comparable apartments for 24 months. • Households overestimate lighting use by 75% and underestimate HVAC usage by 29%. • Households using the same appliances show substantial variations in electricity use. • Plug load accounts for the largest share of electricity use at all hours of the day. • Savings of 11% were achieved by replacing old refrigerators

  9. Air conditioning with small power gas appliances

    International Nuclear Information System (INIS)

    Canci, Franco

    1997-01-01

    This article describes research and test activities on small power air conditioning appliances for residential use carried out in the United States, Japan and Europe. The absorption technology aims at the following objectives: to develop appliances requiring reduced maintenance and having a size comparable with electric units of the same output; to reduce production costs and therefore the final prince by adopting special manufacturing technologies such as welded plate exchangers; to obtain appliances which operate both in summer and winter ( as heat pumps), allowing to minimize management and installation costs in southern European climates. The final aim is to offer the customer one appliance only for the following purposes: hot water production for sanitary use, water refrigeration for summer air conditioning, hot water production production for winter heating. This kind of appliance should have management and maintenance costs similar to current individual boilers

  10. Study on Semantic Assets for Smart Appliances Interoperability : D-S3: THIRD INTERIM REPORT

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2015-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  11. Study on Semantic Assets for Smart Appliances Interoperability : D-S2: SECOND INTERIM REPORT

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2014-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  12. Study on Semantic Assets for Smart Appliances Interoperability : D-S1: FIRST INTERIM REPORT

    NARCIS (Netherlands)

    Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

    2014-01-01

    About two thirds of the energy consumed by buildings originates from the residential sectors and thus household appliances. Household appliances or home appliances are electrical/mechanical machines which accomplish some household functions. Nowadays, appliances are not stand-alone systems anymore.

  13. Energy and associated greenhouse gas emissions from household appliances in Malaysia

    International Nuclear Information System (INIS)

    Saidur, R.; Masjuki, H.H.; Jamaluddin, M.Y.; Ahmed, S.

    2007-01-01

    Today, electricity is an indispensable key for civilization and development. The trend of electricity consumption is rather escalating. Electricity generation principally depends upon fossil fuels. In one hand, the stocks of these fuels have been confirmed to be critically limited. On the other hand, in process of electricity generation by means of these fuels, a number of poisonous by-products adversely affect the conservation of natural eco-system. Further, electricity driven appliances use emanate anti-environmental gases that also affect human health and climate. Therefore, estimation of energy consumption for operating household appliances, savings of energy under policy intervention, and emission of poisonous gases in a fast developing country deserve academic attention. This paper focuses on estimation of energy consumption, energy savings, reduction of emissions of greenhouse gases for use of household appliances in Malaysia between 1999 and 2015. In the upstream side of electricity generation, the study estimates the amount of greenhouse gases (GHGs) resulting from burning of fossil fuels. In downstream side, it considers the energy savings and reduction of CHGs. The results show that significant amount of energy can be saved and thus huge volume of toxic emissions can be controlled. The findings can be useful to policy makers as well as household appliances users

  14. What's driving energy efficient appliance label awareness and purchase propensity?

    International Nuclear Information System (INIS)

    Mills, Bradford; Schleich, Joachim

    2010-01-01

    The EU appliance energy consumption labeling scheme is a key component of efforts to increase the diffusion of energy-efficient household appliances. In this paper, the determinants of consumer knowledge of the energy label for household appliances and the choice of class-A energy-efficient appliances are jointly estimated using data from a large survey of more than 20,000 German households. The results for five major appliances suggest that lack of knowledge of the energy label can generate considerable bias in both estimates of rates of uptake of class-A appliances and in estimates of the underlying determinants of choice of class-A appliance. Simulations of the choice to purchase a class-A appliance, given knowledge of the labeling framework, reveal that residence characteristics and, in several cases, regional electricity prices strongly increase the propensity to purchase a class-A appliance, but socio-economic characteristics have surprisingly little impact on appliance energy-class choice.

  15. Appliance based control for Home Power Management Systems

    International Nuclear Information System (INIS)

    Özkan, Hanife Apaydın

    2016-01-01

    This study scrutinizes energy-friendly smart home appliances (hereafter ‘smart appliances’), control of these appliances and their effects on the efficient use of energy. To accomplish this, smart appliances and their operation principles are introduced and their energy savings compared to conventional appliances are analyzed using precise measurements. Then, a real-time Appliance-based Home Power Management System (Ab-HPMS) which manages power consumption of smart appliances and that of the house as a whole is proposed. For Ab-HPMS, an appliance control algorithm, called Appliance-based Rolling Wave Planning (Ab-RWP), is developed with the aim of reducing electricity cost and improving energy efficiency while maintaining user comfort. Ab-RWP algorithm interacts with appliances in a priority order based on user comfort which is determined by utilizing their smart operational characteristics. Operations of smart appliances and their integrations with Ab-HPMS are modeled with Petri nets to verify that they meet the requirements expressed in the specifications. Simulation results demonstrate that proposed Ab-HPMS provides improvements in terms of the energy consumption reduction of about 5%–16%, cost reduction of about 10%–24% and peak reduction at high demand period of about 38%–53% compared to conventional appliances usage. - Highlights: • The effects of smart home appliances on energy saving are investigated. • Petri nets models of smart appliances are developed to simulate their operations in smart home. • A real-time appliance-based home power management system (Ab-HPMS) is proposed. • Power density function is evaluated to interrupt the operation of smart washing machine.

  16. The greenhouse advantage of natural gas appliances

    International Nuclear Information System (INIS)

    Coombe, N.

    2000-01-01

    The life cycle report prepared recently by Energetics for the AGA, Assessment of Greenhouse Gas Emissions from Natural Gas, demonstrates clearly the greenhouse advantage natural gas has over coal in generating electricity. This study also goes one step further in applying this life cycle approach to the use of space and water heating within the home. The study shows the significant green-house advantage that natural gas appliances have over electric appliances. Findings from other studies also support this claim. The natural gas suppliers are encouraged to take advantage of the marketing opportunity that these studies provide, offering the householders the fuel that will significantly reduce their contribution to greenhouse emission

  17. Eu-energy label for electric appliances; Das EU-Energielabel fuer Elektrogeraete

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-04-15

    When buying a new appliances to have clear and understandable information on energy consumption to avoid later expensive surprices by to high power cost. But European classifiaction A to G of big household appliances is out of date and must be changed.(orig./GL)

  18. Using smart meter to monitor the energy consumption of home appliances

    International Nuclear Information System (INIS)

    Dong, M.; Xu, W.

    2010-01-01

    A smart meter provides the foundation for the smart grid, which represent the future electric system in terms of communications, sensors and automation to improve the flexibility, reliability and efficiency of power systems. Smart meters are installed at the utility-customer interface point to provide real-time power usage and price data to each electricity user. The purpose is to create customer awareness on electricity consumption and help users to conserve energy. Smart meters are being deployed throughout North America to replace most traditional meters. However, this paper discussed a major technical gap of the smart meter. Existing smart meters do not provide households with enough feedback needed to achieve effective energy saving. In order to support the energy conservation effort of a customer, the whole house energy data must be displayed on minute or second basis, and it must also be broken down into individual appliance levels. The data of an appliance's energy usage is the most useful information for users to modify their actions and conserve energy. This paper proposed to make the smart meter capable of reporting the overall consumption of a household, as well as monitoring how individual appliances use electricity. It presented a method on using different appliance signatures to identify appliances and make energy estimations on their respective consumptions. Paired with time-of-use or other real time pricing mechanisms, the method enables customers to save energy. This paper also demonstrated how to implement an algorithm on the smart meter platform. Future work will focus on making the algorithm more accurate and faster, and on integrating the smart meter with an appliance energy monitoring system. 21 refs., 6 tabs., 3 figs.

  19. Realizing potential savings of energy and emissions from efficient household appliances in India

    International Nuclear Information System (INIS)

    Parikh, Kirit S.; Parikh, Jyoti K.

    2016-01-01

    The paper projects households' stock of four major electricity consuming appliances till 2030 and explores policy options to accelerate adoption of more energy efficient appliances. India's rapid economic growth has enabled the growing middle class to buy household appliances in increasing numbers. The consequent rise in energy consumption and GHG emissions can be significantly reduced if consumers are motivated by awareness and options in the market to buy energy efficient appliances. India has introduced a star rating scheme for appliances, and even without incentives consumers purchase star-rated appliances. The stock of household appliances is projected using the data of a national sample survey of household consumption, observed sale of star-rated appliances and projected consumption distribution. Estimated savings in households' electricity consumption from just four appliances, ACs, refrigerators, TVs, and ceiling fans, for which data were available, range from 52 bKwh to 145 bkwh in 2030, reductions of 10–27%. The corresponding reduction in CO_2 emissions will be between 42 Mt and 116 Mt in 2030. With policies of finance and bulk procurement to reduce costs, emissions reduction can be 128 Mt in 2030, a reduction of 30%. - Highlights: • Estimates the stock of selected household appliances with 20 classes of rural and urban households in the years 2030 in India. • Assesses the economics of energy efficient appliances. • Estimates spread of selected energy efficient appliances. • Assesses savings in energy consumption and CO_2 emissions in four alternative scenarios. • Suggests policies to promote energy efficient appliances.

  20. Comparative study of 2 electric and 2 manual toothbrushes in patients with fixed orthodontic appliances.

    Science.gov (United States)

    Thienpont, V; Dermaut, L R; Van Maele, G

    2001-10-01

    The objective of this prospective single-blind crossover clinical trial was to evaluate the efficacy of 4 toothbrushes in 33 children undergoing fixed appliance orthodontic therapy. The toothbrushes included in this study were the Braun Oral-B 3D Plaque Remover (Kronberg, Germany), the Philips-Jordan HP 510 (Philips Domestic Appliances, Groningen, The Netherlands), the Lactona orthodontic toothbrush (Bergen op Zoom, The Netherlands), and the Oral-B Advantage Control Grip (Braun); the first 2 are electric, and the last 2 are manual. Every patient tested each type of toothbrush in a randomly designed sequence. Plaque and gingival scores were recorded at baseline and after every 4-week test period. All patients received professional prophylaxis after each clinical evaluation. The data were analyzed with the Friedman test, which showed no significant differences among the 4 brushes for any of the parameters measured. The Wilcoxon signed rank test, comparing the plaque and the gingival scores between the upper and lower jaw for each brush, indicated that plaque removal was more efficient in the lower jaw than in the upper.

  1. A Support System for the Electric Appliance Control Using Pose Recognition

    Science.gov (United States)

    Kawano, Takuya; Yamamoto, Kazuhiko; Kato, Kunihito; Hongo, Hitoshi

    In this paper, we propose an electric appliance control support system for aged and bedridden people using pose recognition. We proposed a pose recognition system that distinguishes between seven poses of the user on the bed. First, the face and arm regions of the user are detected by using the skin color. Our system focuses a recognition region surrounding the face region. Next, the higher order local autocorrelation features within the region are extracted. The linear discriminant analysis creates the coefficient matrix that can optimally distinguish among training data from the seven poses. Our algorithm can recognize the seven poses even if the subject wears different clothes and slightly shifts or slants on the bed. From the experimental results, our system achieved an accuracy rate of over 99 %. Then, we show that it possibles to construct one of a user-friendly system.

  2. Comparison of emissions from selected commercial kitchen appliances and food products

    Energy Technology Data Exchange (ETDEWEB)

    Kuehn, T.H.; Gerstler, W.D.; Pui, D.Y.H.; Ramsey, J.W.

    1999-07-01

    Effluents have been measured from various grease-producing cooking processes in an attempt to quantify the emissions that enter typical commercial kitchen exhaust hoods. The appliances tested include gas and electric versions of single-sided griddles, open-vat deep fat fryers, under-fired broilers, full size convection ovens, and six burner ranges. Food products include hamburger, chicken breast, fries, sausage pizza, and a spaghetti meal. Emission data were obtained for particles, grease vapor, CO, CO{sub 2}, NO{sub x}, and hydrocarbons. Velocity and temperature fields were measured in the plume above each appliance. Results show that a large fraction of the grease emission is typically in vapor form. The broilers emit significantly more particles less than 2.5 {micro}m in size (PM 2.5) than the other appliances tested. Combustion by-products were measured for all gas appliances. Both the gas and electric broilers emitted significant amounts of CO when hamburgers were cooked. Aromatic hydrocarbon concentrations were below detectable limits in all tests.

  3. The Next Generation of Appliances: Visions for Sustainability

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen; Guldbrandsen, Tom

    1998-01-01

    to consume no more than 50 kWh per year, without using any risky synthetic gasses. Washing appliances will use no electricity for heating, which will bring annual electricity consumption below 50 kWh for a washing machine. For electronic equipment, the efficiency gain known from battery operated version...

  4. Advances in household appliances- A review

    International Nuclear Information System (INIS)

    Bansal, Pradeep; Vineyard, Edward; Abdelaziz, Omar

    2011-01-01

    An overview of options and potential barriers and risks for reducing the energy consumption, peak demand, and emissions for seven key energy consuming residential products (refrigerator-freezers, dishwashers, clothes washers, clothes dryers, electric ovens, gas ovens and microwave ovens) is presented. The paper primarily concentrates on the potential energy savings from the use of advanced technologies in appliances for the U.S. market. The significance and usefulness of each technology was evaluated in order to prioritize the R and D needs to improve energy efficiency of appliances in view of energy savings, cost, and complexity. The paper provides a snapshot of the future R and D needs for each of the technologies along with the associated barriers. Although significant energy savings may be achieved, one of the major barriers in most cases is high first cost. One way of addressing this issue and promoting the introduction of new technologies is to 'level' the playing field for all manufacturers by establishing Minimum Energy Performance Standards (MEPS) which are not cost prohibitive and promoting energy efficient products through incentives to both manufacturers and consumers. - Highlights: → This paper presents latest developments/status of advanced residential appliances. → Stringent minimum energy performance standards can reduce appliance energy use. → There is a potential to reduce energy use in appliances by up to 50%.

  5. Real-time identification of residential appliance events based on power monitoring

    Science.gov (United States)

    Yang, Zhao; Zhu, Zhicheng; Wei, Zhiqiang; Yin, Bo; Wang, Xiuwei

    2018-03-01

    Energy monitoring for specific home appliances has been regarded as the pre-requisite for reducing residential energy consumption. To enhance the accuracy of identifying operation status of household appliances and to keep pace with the development of smart power grid, this paper puts forward the integration of electric current and power data on the basis of existing algorithm. If average power difference of several adjacent cycles varies from the baseline and goes beyond the pre-assigned threshold value, the event will be flagged. Based on MATLAB platform and domestic appliances simulations, the results of tested data and verified algorithm indicate that the power method has accomplished desired results of appliance identification.

  6. FY 2000 report on the results of the development of the stand-by consumption power reduction technology. Verification experiment on the technology to reduce stand-by power of household electric appliances; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden seihin taikiji denryoku sakugen gijutsu no jissho jikken

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Study was made of the energy conservation by reducing stand-by consumption power of household electric appliances. In the study, remote control, household electric appliance, and outlet box were developed, and a system was developed in which each of the three was connected by network and the commercial power source supply is cut off at the time of the stand-by state of household electric appliances. The outlet box collectively manages timer information and reservation information. User sends out control command toward the outlet box using the two-way remote control, and controls all the household electric appliances connected via network. The screen data of household electric appliances are sent to the two-way remote control via the outlet box and presented to user. When the time comes for automatic execution such as video recording during absence, the outlet box carries commercial power source to household electric appliances. Using these appliances, verification experiment was carried out in the model house which was built with the ordinary house as model. A reduction in stand-by consumption power, approximately 218kWh/year(center dot)household, was verified. (NEDO)

  7. Technical and legal application possibilities of the compulsory labelling of the standby consumption of electrical household and office appliances - Project No. 53/03. Summary of the final report for the Federal Ministry of Economics and Labour

    Energy Technology Data Exchange (ETDEWEB)

    Schlomann, B.; Cremer, C.; Friedewald, M. [Fraunhofer-Institut fuer Systemtechnik und Innovationsforschung, Karlsruhe (DE)] (and others)

    2005-06-13

    The standby consumption of electrical households and office appliances continues to be significant world-wide since the number of products with standby components is constantly increasing. For Germany, a recent assessment of the Fraunhofer ISI (Cremer et al. 2003) for 2001 arrived at an electricity demand of almost 15 TWh for household and office appliances in standby mode. i.e. in standby and off-mode. This represents almost 40% of the total consumption of these appliances and around 3% of the total electricity demand of the final energy sectors in Germany. The standby share in electricity demand is over 80 or even 90% for numerous appliances. The Federal Environmental Agency calculated that every year standby losses in German households and offices are responsible for wasted electricity amounting to 3.5 billion Euro (UBA 2004). For the OECD countries, field studies show that between 3 and 13% of the electricity consumption of households can be ascribed to standby losses (IEA 2001). Without energy policy measures on both national and international levels, there is a great risk that a further increase in standby consumption will occur. Many studies dealing with this subject have already been conducted and have shown that low standby consumption is technically feasible and usually achievable at a reasonable cost. One possible energy policy measure to reduce the standby consumption of electrical household and office appliances is the introduction of mandatory consumption labelling. In principle, a high degree of effectiveness is attributed to such regulatory/command-and-control measures with regard to influencing the energy efficiency of devices. Compulsory energy labels to identify and, where necessary, to classify electricity consumption produce greater market transparency and offer buyers an additional decision criterion. In this way they promote indirectly the development, production and supply of energy-efficient products. When combined with comparatively low

  8. Wood-burning appliances and indoor air quality

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, Benoit; Allaire, Sylvain; Gauvin, Denis; Gingras, Suzanne; Rhainds, Marc; Prud' Homme, Henri; Duchesne, Jean-Francois [CHUQ-Centre de Recherche du CHUL, Unite de Recherche en Sante Publique, 2400, d' Estimauville, Beauport, G1E 7G9 Quebec (Canada); Koutrakis, Petros [Harvard School of Public Health, 677 Huntington Avenue, Boston, MA 02115 (United States)

    2001-12-17

    Wood heating represents an interesting economic alternative to electrical or heating oil and gas systems. However, many people are concerned about poor indoor air quality in homes equipped with wood-burning appliances. We conducted a study in the Quebec City region (Canada) to verify the extent of indoor air contamination, and to examine the frequency of respiratory symptoms and illnesses among occupants of wood-heated homes. One child attending primary school (median=8 years old; range=5-14 years old) and an adult (median=37 years old; range=23-52 years old) were recruited in each eligible house. Eligible houses were without known sources of combustion products (smokers, attached garage, oil or gas furnace, gas stove, etc.) except for wood-burning appliance. Out of the 89 houses included in the study, 59 had wood-burning appliances. Formaldehyde, nitrogen dioxide, respirable particles (PM10) and carbon monoxide were measured in a sub-set of 49 houses (41 with a wood-burning appliance and 8 without). The frequency of respiratory symptoms and diseases among participants were documented using a daily symptom diary. Concentrations of contaminants were low in most houses, both with or without a wood-burning appliance. Globally, there was no consistent relationship between the presence of a wood-burning appliance and respiratory morbidity in residents. Nevertheless, residents who mentioned being exposed to fumes emitted by such an appliance reported more respiratory illnesses and symptoms. The presence of animals or molds, and keeping windows closed most of the time in winter were other factors associated with respiratory problems. We conclude that wood burning appears to be a respiratory health risk for occupants if the appliance is not maintained and used properly.

  9. Optimal residential smart appliances scheduling considering distribution network constraints

    Directory of Open Access Journals (Sweden)

    Yu-Ree Kim

    2016-01-01

    Full Text Available As smart appliances (SAs are more widely adopted within distribution networks, residential consumers can contribute to electricity market operations with demand response resources and reduce their electricity bill. However, if the schedules of demand response resources are determined only by the economic electricity rate signal, the schedule can be unfeasible due to the distribution network constraints. Furthermore, it is impossible for consumers to understand the complex physical characteristics and reflect them in their everyday behaviors. This paper introduces the concept of load coordinating retailer (LCR that deals with demand responsive appliances to reduce electrical consumption for the given distribution network constraints. The LCR can play the role of both conventional retailer and aggregated demand response provider for residential customers. It determines the optimal schedules for the aggregated neighboring SAs according to their types within each distribution feeder. The optimization algorithms are developed using Mixed Integer Linear Programming, and the distribution network is solved by the Newton–Raphson AC power flow.

  10. Transforce lingual appliances pre-adjusted invisible appliances simplify treatment.

    Science.gov (United States)

    Clark, William John

    2011-01-01

    Transforce lingual appliances are designed to be used in conjunction with conventional fixed appliances. Lingual arch development is normally followed by bonded fixed appliances to detail the occlusion. Alternatively Transforce appliance treatment is an efficient method of preparing complex malocclusions prior to a finishing stage with invisible appliances. This approach is ideal for adult treatment, using light continuous forces for arch development with appliances that are comfortable to wear. Sagittal and Transverse appliances are designed for arch development in a range of sizes for contracted arches. They can be used to treat all classes of malocclusion and are pre-adjusted fixed/removable devices for non-compliance treatment. Force modules with nickel titanium coil springs enclosed in a tube deliver a gentle, biocompatible continuous force with a long range of action. They are excellent for mixed dentition and ideal for adult arch development. There are multiple sizes for upper and lower arch development and a sizing chart may be placed over a study model for correct selection, eliminating the need for laboratory work.

  11. Emissions from SF6 appliances in Norway. Additional report No. 2

    International Nuclear Information System (INIS)

    Gjarede, Anne Cathrine

    1999-01-01

    The report presents facts regarding the Norwegian SF 6 emissions and the significance for the Norwegian climatic gas accounts in order to evaluate whether 12-24 kV SF 6 appliances are environmentally acceptable. Estimations show that emissions from such equipment contribute with about 0.2 % of the total Norwegian CO 2 emissions in 1993. The SF 6 which is stored in electric appliances, may either be recycled or decomposed to more environmentally acceptable end products. The report concludes that the contribution to the greenhouse effects from SF 6 appliances is minimal

  12. Dynamic Appliances Scheduling in Collaborative MicroGrids System

    Science.gov (United States)

    Bilil, Hasnae; Aniba, Ghassane; Gharavi, Hamid

    2017-01-01

    In this paper a new approach which is based on a collaborative system of MicroGrids (MG’s), is proposed to enable household appliance scheduling. To achieve this, appliances are categorized into flexible and non-flexible Deferrable Loads (DL’s), according to their electrical components. We propose a dynamic scheduling algorithm where users can systematically manage the operation of their electric appliances. The main challenge is to develop a flattening function calculus (reshaping) for both flexible and non-flexible DL’s. In addition, implementation of the proposed algorithm would require dynamically analyzing two successive multi-objective optimization (MOO) problems. The first targets the activation schedule of non-flexible DL’s and the second deals with the power profiles of flexible DL’s. The MOO problems are resolved by using a fast and elitist multi-objective genetic algorithm (NSGA-II). Finally, in order to show the efficiency of the proposed approach, a case study of a collaborative system that consists of 40 MG’s registered in the load curve for the flattening program has been developed. The results verify that the load curve can indeed become very flat by applying the proposed scheduling approach. PMID:28824226

  13. Wisdom Appliance Control System

    Science.gov (United States)

    Hendrick; Jheng, Jyun-Teng; Tsai, Chen-Chai; Liou, Jia-Wei; Wang, Zhi-Hao; Jong, Gwo-Jia

    2017-07-01

    Intelligent appliances wisdom involves security, home care, convenient and energy saving, but the home automation system is still one of the core unit, and also using micro-processing electronics technology to centralized and control the home electrical products and systems, such as: lighting, television, fan, air conditioning, stereo, it composed of front-controller systems and back-controller panels, user using front-controller to control command, and then through the back-controller to powered the device.

  14. Reduction of electric power consumption in relation to household appliances. Elbesparelser ved husholdningsapparater; Forprojekt

    Energy Technology Data Exchange (ETDEWEB)

    Gydesen, A.

    1989-07-15

    Possibilities were investigated for the reduction of electric power consumption in relation to household appliances, and for cooperation with manufacturers in this respect. It is suggested that in the cases of washing-up machines, and washing and drying machines, hot water from the tap could be utilized. This would mean that the energy consumption would then shift to domestic heating equipment, dual-purpose power plants and district heating plants. Ovens, drying machines, washing machines and washing-up machines could use natural gas, especially in areas where this fuel could be conveyed to each household via pipes. Cooperation with manufacturers seems feasible, especially with regard to electric ovens, saucepans for use in combination with the latter, and water beds. Considering future developments, it is reasonable to expect that ultra sound will be utilized in connection with washing-up and washing machines, moreover it is likely that the use of enzymes in washing powders will mean that washing machines will be able to run on cold water. (AB) 21 refs.

  15. Electronic Control System Of Home Appliances Using Speech Command Words

    Directory of Open Access Journals (Sweden)

    Aye Min Soe

    2015-06-01

    Full Text Available Abstract The main idea of this paper is to develop a speech recognition system. By using this system smart home appliances are controlled by spoken words. The spoken words chosen for recognition are Fan On Fan Off Light On Light Off TV On and TV Off. The input of the system takes speech signals to control home appliances. The proposed system has two main parts speech recognition and smart home appliances electronic control system. Speech recognition is implemented in MATLAB environment. In this process it contains two main modules feature extraction and feature matching. Mel Frequency Cepstral Coefficients MFCC is used for feature extraction. Vector Quantization VQ approach using clustering algorithm is applied for feature matching. In electrical home appliances control system RF module is used to carry command signal from PC to microcontroller wirelessly. Microcontroller is connected to driver circuit for relay and motor. The input commands are recognized very well. The system is a good performance to control home appliances by spoken words.

  16. Motor-pump unit provided with a lifting appliance of the motor

    International Nuclear Information System (INIS)

    Veronesi, Luciano; Francis, W.R.

    1978-01-01

    This invention relates to lifting appliances and particularly concerns a 'pump and motor set' or motor-pump unit fitted with a lifting appliance enabling the motor to be separated from the pump. In nuclear power stations the reactor discharges heat that is carried by the coolant to a distant point away from the reactor to generate steam and electricity conventionally. In order to cause the reactor coolant to flow through the system, coolant motor-pump units are provided in the cooling system. These units are generally of the vertical type with an electric motor fitted vertically on the pump by means of a cylindrical or conical structure called motor support [fr

  17. Domestic appliances energy optimization with model predictive control

    International Nuclear Information System (INIS)

    Rodrigues, E.M.G.; Godina, R.; Pouresmaeil, E.; Ferreira, J.R.; Catalão, J.P.S.

    2017-01-01

    Highlights: • An alternative power management control for home appliances that require thermal regulation is presented. • A Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat. • Problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. • A modulation scheme of a two-level Model Predictive Control signal as an interface block is presented. • The implementation costs in home appliances with thermal regulation requirements are reduced. - Abstract: A vital element in making a sustainable world is correctly managing the energy in the domestic sector. Thus, this sector evidently stands as a key one for to be addressed in terms of climate change goals. Increasingly, people are aware of electricity savings by turning off the equipment that is not been used, or connect electrical loads just outside the on-peak hours. However, these few efforts are not enough to reduce the global energy consumption, which is increasing. Much of the reduction was due to technological improvements, however with the advancing of the years new types of control arise. Domestic appliances with the purpose of heating and cooling rely on thermostatic regulation technique. The study in this paper is focused on the subject of an alternative power management control for home appliances that require thermal regulation. In this paper a Model Predictive Control scheme is assessed and its performance studied and compared to the thermostat with the aim of minimizing the cooling energy consumption through the minimization of the energy cost while satisfying the adequate temperature range for the human comfort. In addition, the Model Predictive Control problem formulation is explored through tuning weights with the aim of reducing energetic consumption and cost. For this purpose, the typical consumption of a 24 h period of a summer day was simulated a three-level tariff scheme was used. The new

  18. Energy labeling for electric fans in Malaysia

    International Nuclear Information System (INIS)

    Mahlia, T.M.I.; Masjuki, H.H.; Taha, F.M.; Rahim, N.A.; Saidur, R.

    2005-01-01

    To reduce energy consumption in the residential sector, Malaysia Energy Commission is considering implementing energy labels for household electrical appliances including electric fans in 2005. The purpose of the energy labels is to provide the consumers a guideline to compare the size, features, price and efficiency of the appliance. This paper discusses the energy label for electric fans in this country based on Malaysian Standards developed by a technical committee that reviewed the performance of household electrical appliances. This study includes methodology for the calculation of the energy efficiency star rating and projected energy usage, performance requirements, details of the energy label and the requirements for the valid application in Malaysia. The label also can be adopted for other household electrical appliances with only slight modifications

  19. Non-intrusive appliance load monitoring system based on a modern kWh-meter

    Energy Technology Data Exchange (ETDEWEB)

    Pihala, H. [VTT Energy, Espoo (Finland). Energy Systems

    1998-12-01

    Non-intrusive appliance load monitoring (NIALM) is a fairly new method to estimate load profiles of individual electric appliances in a small building, like a household, by monitoring the whole load at a single point with one recording device without sub-meters. Appliances have special electrical characteristics, the positive and negative active and reactive power changes during the time they are switched on or off. These changes are called events and are detected with a monitoring device called an event recorder. Different NIALM-concepts developed in Europe and in the United States are generally discussed. The NIALM-concept developed in this study is based on a 3-phase, power quality monitoring kWh-meter and unique load identification algorithms. This modern kWh-meter with a serial data bus to a laptop personal computer is used as die event recorder. The NIALM-concept of this presentation shows for the first time how a kWh-meter can be used at the same time for billing, power quality and appliance end-use monitoring. An essential part of the developed NIALM-system prototype is the software of load identification algorithms which runs in an off-line personal computer. These algorithms are able to identify, with a certain accuracy, both two-state and multi-state appliances. This prototype requires manual-setup in which the naming of appliances is performed. The results of the prototype NIALMS were verified in a large, single family detached house and they were compared to the results of other prototypes in France and the United States, although this comparison is difficult because of different supply systems, appliance stock and number of tested sites. Different applications of NIALM are discussed. Gathering of load research data, verification of DSM-programs, home automation, failure analysis of appliances and security surveillance of buildings are interesting areas of NIALM. Both utilities and customers can benefit from these applications. It is possible to

  20. Real-Time Recognition Non-Intrusive Electrical Appliance Monitoring Algorithm for a Residential Building Energy Management System

    Directory of Open Access Journals (Sweden)

    Kofi Afrifa Agyeman

    2015-08-01

    Full Text Available The concern of energy price hikes and the impact of climate change because of energy generation and usage forms the basis for residential building energy conservation. Existing energy meters do not provide much information about the energy usage of the individual appliance apart from its power rating. The detection of the appliance energy usage will not only help in energy conservation, but also facilitate the demand response (DR market participation as well as being one way of building energy conservation. However, energy usage by individual appliance is quite difficult to estimate. This paper proposes a novel approach: an unsupervised disaggregation method, which is a variant of the hidden Markov model (HMM, to detect an appliance and its operation state based on practicable measurable parameters from the household energy meter. Performing experiments in a practical environment validates our proposed method. Our results show that our model can provide appliance detection and power usage information in a non-intrusive manner, which is ideal for enabling power conservation efforts and participation in the demand response market.

  1. Choosing Wood Burning Appliances

    Science.gov (United States)

    Information to assist consumers in choosing a wood burning appliance, including types of appliances, the differences between certified and non-certified appliances, and alternative wood heating options.

  2. PAT portable appliance testing

    CERN Document Server

    2011-01-01

    The Electricity at Work Regulations 1989 require any electrical system to be constructed, maintained and used in such a manner as to prevent danger. This means that inspection and testing of systems, including portable appliances, is needed in order to determine if maintenance is required.This book explains in clear language what needs to be done and includes expert advice on legislation as well as actual testing. The book contains an appendix providing the electrical fundamentals needed by non-specialists and also has sample questions (with answers) for the C&G 2377 exam that anyone who conducts this work is required to take by law.It is an affordable and handy reference for electricians who administer PAT. It is also an ideal refesher and revision guide for the non-specialist, such as maintenance staff, caretakers and charity shop volunteers who carry out these tasks part-time, alongside their many other duties.Brian Scaddan, I Eng, MIET, is a consultant for and an Honorary Member of City & Guilds. ...

  3. A Study on Efficient Energy Use for Household Appliances in Malawi

    African Journals Online (AJOL)

    Keywords: Efficient , energy use, household appliances, power consumption. ... Although the hydro-electric power transmission lines extend the entire length of ..... R. Karri and P. Mishra, “Minimizing Energy Consumption of Secure Wireless ...

  4. Development of the Optimum Operation Scheduling Model of Domestic Electric Appliances for the Supply-Demand Adjustment in a Power System

    Science.gov (United States)

    Ikegami, Takashi; Iwafune, Yumiko; Ogimoto, Kazuhiko

    The high penetration of variable renewable generation such as Photovoltaic (PV) systems will cause the issue of supply-demand imbalance in a whole power system. The activation of the residential power usage, storage and generation by sophisticated scheduling and control using the Home Energy Management System (HEMS) will be needed to balance power supply and demand in the near future. In order to evaluate the applicability of the HEMS as a distributed controller for local and system-wide supply-demand balances, we developed an optimum operation scheduling model of domestic electric appliances using the mixed integer linear programming. Applying this model to several houses with dynamic electricity prices reflecting the power balance of the total power system, it was found that the adequate changes in electricity prices bring about the shift of residential power usages to control the amount of the reverse power flow due to excess PV generation.

  5. Assessment of perceived orthodontic appliance attractiveness.

    Science.gov (United States)

    Ziuchkovski, James P; Fields, Henry W; Johnston, William M; Lindsey, Delwin T

    2008-04-01

    To date, no studies have been published in the literature evaluating the esthetics of orthodontic appliances. The purpose of this study was to assess appliance variables, including appliance type, brand, wire, and ligature tie, for their relative attractiveness. Demographic factors were also evaluated. Appliances were placed in an adult, and digital images were captured, standardized, and incorporated into a computer-based survey. Subjects (n = 200) rated each image for attractiveness on a visual analog scale. The attractiveness ratings were analyzed by using factorial analysis of variance with repeated measures. Post-hoc testing was done with the Tukey-Kramer test (overall a appliances), ceramic, and all self-ligating/stainless steel appliances. No differences between brands in each appliance type were found. Ratings of some ceramic appliances were significantly affected by archwire and ligature tie, depending on several demographic interactions. Orthodontic appliance attractiveness varies by the following hierarchy of appliance types: alternative > ceramic > all stainless steel/self-ligating. Wire and tie selection can affect the appearance of ceramic appliances but have no impact on stainless steel or self-ligating appliances. Certain demographic factors have variable effects on attractiveness ratings.

  6. A segmented appliance for space closure followed by Invisalign and fixed appliances.

    Science.gov (United States)

    Uribe, Flavio; Cutrera, Alice; Nanda, Ravinda

    2011-01-01

    This case report describes the use of a segmented appliance for space closure prior to using Invisalign. The maxillary right canine was retracted into the extracted first premolar space with a sectional wire from the first molar to the canine with no visible brackets in the incisor region. The advantage of this technique is the ability to achieve better root and rotational control during space closure with a fixed appliance that also has limited visibility. A maxillary fixed appliance was used to refine the esthetics in the maxillary arch due to the limitations of the Invisalign appliance in achieving rotational and vertical movements.

  7. Disposal machine using a hydraulic shovel loader for waste home electric appliances; Yuatsu shoberunado wo katsuyoshita haikaden shori kikai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-25

    This paper presents a disposal machine system developed by Hitachi Kenki Co. for waste home appliances. EX60 disposal machine and 2-axis shear shredder were developed as work machines for volume reduction and efficient disposal of waste home appliances. The shredder with rotary cutters is featured by superior crunch performance and efficient shredding of waste home appliances, and can crash not only waste home appliances but also various objects such as bulky waste, waste plastics and waste tire for passenger cars at crash torques from 7000 to 12000kgf{center_dot}m. The shredder is featured by superior mobility and easy operability by self-running and full-hydraulic driving, low- noise engine, and noise/vibration reduction by low-speed large torque hydraulic motor. EX60 disposal machine has clamp fixing waste home appliances, and a grapple for disassembling and classification, and can efficiently disassemble and classify 4 kinds of waste home appliances and other wastes only by itself. 12 figs., 3 tabs.

  8. Cost-benefit analysis: introducing energy efficient and renewable energy appliances in Lebanese households

    Energy Technology Data Exchange (ETDEWEB)

    Ruble, Isabella [American University of Beirut, Department of Economics (Lebanon)], E-mail: economics.ir@gmail.com

    2011-07-01

    In Lebanon, neglect of the electricity sector has led to a serious shortage in installed capacity. Recently, the government of Lebanon declared its intention to raise the share of renewable energy (RE) year by year in order to reduce energy consumption. This paper gave a cost-benefit analysis and reviewed the replacement of five major traditional household appliances with their energy efficient (EE) or renewable energy counterparts. This initiative would mostly be felt in three main areas: electricity consumption, consumer costs, and government expenditure. There is a strong possibility that the electricity demand of the 1.2 million Lebanese households can be reduced by introduction of these EE household appliances. Benefits would also accrue to the government in the form of avoided subsidies and reduced need for installed capacity. This paper finds that the benefits to be expected from these policy recommendations largely outweigh the costs.

  9. Scheduling Appliances with GA, TLBO, FA, OSR and Their Hybrids Using Chance Constrained Optimization for Smart Homes

    Directory of Open Access Journals (Sweden)

    Zunaira Nadeem

    2018-04-01

    Full Text Available In this paper, we design a controller for home energy management based on following meta-heuristic algorithms: teaching learning-based optimization (TLBO, genetic algorithm (GA, firefly algorithm (FA and optimal stopping rule (OSR theory. The principal goal of designing this controller is to reduce the energy consumption of residential sectors while reducing consumer’s electricity bill and maximizing user comfort. Additionally, we propose three hybrid schemes OSR-GA, OSR-TLBO and OSR-FA, by combining the best features of existing algorithms. We have also optimized the desired parameters: peak to average ratio, energy consumption, cost, and user comfort (appliance waiting time for 20, 50, 100 and 200 heterogeneous homes in two steps. In the first step, we obtain the optimal scheduling of home appliances implementing our aforementioned hybrid schemes for single and multiple homes while considering user preferences and threshold base policy. In the second step, we formulate our problem through chance constrained optimization. Simulation results show that proposed hybrid scheduling schemes outperformed for single and multiple homes and they shift the consumer load demand exceeding a predefined threshold to the hours where the electricity price is low thus following the threshold base policy. This helps to reduce electricity cost while considering the comfort of a user by minimizing delay and peak to average ratio. In addition, chance-constrained optimization is used to ensure the scheduling of appliances while considering the uncertainties of a load hence smoothing the load curtailment. The major focus is to keep the appliances power consumption within the power constraint, while keeping power consumption below a pre-defined acceptable level. Moreover, the feasible regions of appliances electricity consumption are calculated which show the relationship between cost and energy consumption and cost and waiting time.

  10. Evaluation of advanced technologies for residential appliances and residential and commercial lighting

    Energy Technology Data Exchange (ETDEWEB)

    Turiel, I.; Atkinson, B.; Boghosian, S.; Chan, P.; Jennings, J.; Lutz, J.; McMahon, J.; Rosenquist, G.

    1995-01-01

    Section 127 of the Energy Policy Act requires that the Department of Energy (DOE) prepare a report to Congress on the potential for the development and commercialization of appliances that substantially exceed the present federal or state efficiency standards. Candidate high-efficiency appliances must meet several criteria including: the potential exists for substantial improvement (beyond the minimum established in law) of the appliance`s energy efficiency; electric, water, or gas utilities are prepared to support and promote the commercialization of such appliances; manufacturers are unlikely to undertake development and commercialization of such appliances on their own, or development and production would be substantially accelerated by support to manufacturers. This report describes options to improve the efficiency of residential appliances, including water heaters, clothes washers and dryers, refrigerator/freezers, dishwashers, space heating and cooling devices, as well as residential and commercial lighting products. Data from this report (particularly Appendix 1)were used to prepare the report to Congress mentioned previously. For the residential sector, national energy savings are calculated using the LBL Residential Energy Model. This model projects the number of households and appliance saturations over time. First, end-use consumption is calculated for a base case where models that only meet the standard replace existing models as these reach the end of their lifetime. Second, models with efficiencies equal to the technology under consideration replace existing models that reach the end of their lifetime. For the commercial sector, the COMMEND model was utilized to project national energy savings from new technologies. In this report, energy savings are shown for the period 1988 to 2015.

  11. Emissions from wood domestic heating appliances

    International Nuclear Information System (INIS)

    Collet, S.

    2009-01-01

    Much research has been carried out to study emissions from wood domestic heating appliances. This work reviews the available emission factors about pollutants produced in different types of wood domestic heating appliances. The main sources of pollutants are older stoves that in most cases are used as an additional heating appliance. These stoves causes higher emissions than modern appliances. Then, substitution of an old type wood appliance with a modern appliance or boiler or a pellet boilers, would reduce considerably emissions in this sector. The efficiency of this measure is estimated for each pollutant. (author)

  12. 49 CFR 236.308 - Mechanical or electric locking or electric circuits; requisites.

    Science.gov (United States)

    2010-10-01

    ..., AND APPLIANCES Interlocking Standards § 236.308 Mechanical or electric locking or electric circuits; requisites. Mechanical or electric locking or electric circuits shall be installed to prevent signals from... 49 Transportation 4 2010-10-01 2010-10-01 false Mechanical or electric locking or electric...

  13. Treatment of cooling appliances. Interrelations between environmental protection, resource conservation, and recovery rates

    International Nuclear Information System (INIS)

    Laner, David; Rechberger, Helmut

    2007-01-01

    The treatment of cooling appliances in Austria is primarily influenced by two factors. On the one hand is their changing composition and on the other hand the ordinance on Waste Prevention, Collection and Treatment of Waste Electrical and Electronic Equipment (WEEE ordinance), which stipulates a minimum recycling rate of 75% for cooling appliances. This paper investigates whether this recycling rate leads to optimal treatment practices for cooling appliances with respect to resource conservation and environmental protection. Two different treatment technologies which achieve recycling rates between 50-60% and 80-90%, respectively, are compared both for cooling appliances containing Chlorofluorocarbons (CFCs) and for appliances containing Volatile Organic Compounds (VOC). Materials and energy balances are developed for each model. To evaluate resource consumption, expenditures as well as savings of energy and materials are incorporated via the Cumulative Energy Demand (CED). In order to analyse the environmental impact of the different practices, balances for CFC, CO 2 , HF, HCl and solid residues are established. The results show that the treatment type aiming for a maximum of materials recycling contributes more to resource conservation than the other treatment type. But for CFC appliances the former is associated with substantial CFC emissions, which turn out to be most relevant when treating these appliances. Generally, it is found that the optimum recycling rate is a function of the composition of the appliance and the technologies applied, both in recycling and in primary production. A high recycling rate per se does not automatically result in an optimal solution with regard to resource conservation and environmental protection. (author)

  14. A run-around heat exchanger system to improve the energy efficiency of a home appliance using hot water

    International Nuclear Information System (INIS)

    Park, Jae Sung; Jacobi, Anthony M.

    2009-01-01

    A significant portion of the energy consumed by many home appliances using hot water is used to heat cold supply water. Such home appliances generally are supplied water at a temperature lower than the ambient temperature, and the supply water is normally heated to its maximum operating temperature, often using natural gas or an electrical heater. In some cases, it is possible to pre-heat the supply water and save energy that would normally be consumed by the natural gas or electrical heater. In order to save the energy consumed by an appliance using water heater, a run-around heat exchanger system is used to transfer heat from the ambient to the water before an electrical heater is energized. A simple model to predict the performance of this system is developed and validated, and the model is used to explore design and operating issues relevant to the run-around heat exchanger system. Despite the additional power consumption by the fan and pump of the run-around heat exchanger system, the experimental data and analysis show that for some systems the overall energy efficiency of the appliance can be improved, saving about 6% of the energy used by the baseline machine.

  15. Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

    Science.gov (United States)

    Carvalho, F R; Lentini-Oliveira, D; Machado, M A C; Prado, G F; Prado, L B F; Saconato, H

    2007-04-18

    Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adenotonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they change the mandible posture forwards and potentially enlarge the upper airway and increase the upper airspace, improving the respiratory function. To assess the effectiveness of oral appliances or functional orthopaedic appliances for OSAS in children. A sensitive search was developed for the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2005, Issue 3); PubMed (January 1966 to September 2005); EMBASE (1980 to September 2005); Lilacs (1982 to September 2005); BBO-Bibliografia Brasileira de Odontologia (1986 to September 2005); and SciELO (1997 to September 2005). There was no restriction of language or source of information. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiologic function, behavioural problems, drop outs and withdrawals, quality of life, side effects (tolerability), economic evaluation. Data were independently extracted by two review authors. Authors were contacted for additional information. Risk ratios with 95% confidence intervals were calculated for all important dichotomous outcomes. The initial search identified 384 trials

  16. European Gas Appliances Directive and the Dutch Decree on Gas Appliances. Special section

    International Nuclear Information System (INIS)

    De Bruin, B.; Venhorst, T.; Van Tricht, A.

    1998-01-01

    The Gas Appliances Decree is the Dutch translation of the European Gas Appliances Directive. The Decree and the EU Directive contain substantial information, provided they will be read carefully. The EU Directive lays down general safety requirements for gas appliances. They serve as a practical tool for manufacturers and service engineers. In two articles, the Directive is explained, addressing uncertainties and answering important questions. 5 ills

  17. Modeling of GE Appliances in GridLAB-D: Peak Demand Reduction

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Jason C.; Vyakaranam, Bharat GNVSR; Prakash Kumar, Nirupama; Leistritz, Sean M.; Parker, Graham B.

    2012-04-29

    The widespread adoption of demand response enabled appliances and thermostats can result in significant reduction to peak electrical demand and provide potential grid stabilization benefits. GE has developed a line of appliances that will have the capability of offering several levels of demand reduction actions based on information from the utility grid, often in the form of price. However due to a number of factors, including the number of demand response enabled appliances available at any given time, the reduction of diversity factor due to the synchronizing control signal, and the percentage of consumers who may override the utility signal, it can be difficult to predict the aggregate response of a large number of residences. The effects of these behaviors can be modeled and simulated in open-source software, GridLAB-D, including evaluation of appliance controls, improvement to current algorithms, and development of aggregate control methodologies. This report is the first in a series of three reports describing the potential of GE's demand response enabled appliances to provide benefits to the utility grid. The first report will describe the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The second and third reports will explore the potential of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation and the effects on volt-var control schemes.

  18. Introducing mandatory standards for select household appliances in Lebanon: A cost-benefit analysis

    International Nuclear Information System (INIS)

    Ruble, Isabella; Karaki, Sami

    2013-01-01

    Lebanon's energy sector crisis leads to a lack of access to uninterrupted, basic modern electricity services that affects all sectors of the economy. Energy conservation measures are nearly inexistent yet they can potentially lead to substantial reductions in energy demand growth, environmental damages and public expenditures. This paper presents an analysis of the costs and benefits associated with the introduction of mandatory standards for energy efficiency for four different household appliances (refrigerator/freezers, AC split units, washing machines and lighting) over the period 2013–2027. Our results show potential savings in electricity consumption reaching 2054 GW h annually in 2027 as well as a reduction of subsidies paid to the public utility of 3.6 billion USD in 2027 while CO 2 emissions avoided amount to 8.9 million tons over the period of analysis. Furthermore, we propose a financially attractive refrigerator/freezer replacement program for low income households. If this program would cover all existing low-income households in 2013, the savings in electricity consumption would lead to a reduction in subsidies of 9 billion USD (NPV) over the period 2013–2027, while full funding for this program would cost the government 223.8 million USD. This program would thereby benefit consumers, the government and further economic development. - Highlights: ► We model the effect of mandatory appliance standards on electricity consumption. ► We present a refrigerator replacement program contributing to economic development. ► We show that economic efficiency favors the introduction of standards for appliances.

  19. 24 CFR 3280.709 - Installation of appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Installation of appliances. 3280... Fuel Burning Systems § 3280.709 Installation of appliances. (a) The installation of each appliance... the manufacturer's instructions attached to the appliance. Every appliance shall be secured in place...

  20. Enhanced policies for the improvement of electricity efficiencies

    International Nuclear Information System (INIS)

    Blok, Kornelis

    2005-01-01

    Energy-efficiency improvement is considered as an important option to limit greenhouse gas emissions. In this paper, the possibilities to implement new policies to improve the efficiency of electricity end-use are explored. The following policy actions are considered: - introduction of a '1 W standard' for standby power consumption of appliances;- incremental standards for large electric appliances;- design guidelines for small electric appliances;- a technology-forcing standard for lighting;- a motor-drive program;- a program directed at the reduction of electricity use during empty-office hours;- actual energy performance requirements for service-sector buildings. The implementation of these programs will contribute substantially to reaching greenhouse gas emission targets in the European Union (total estimated effect to be 200-350 Mton CO 2 emission reduction in the year 2020). However, to reach these targets a very substantial effort is required, both in terms of policy ambition, force of the applied instruments, and implementation efforts. In the case of electric appliances, regulatory instruments may need wider application. And, in order to attain the substantial potential savings in motor-drive systems, an effort comparable to the effort to promote renewable electricity in the European Union may be both justified and necessary

  1. 24 CFR 3280.707 - Heat producing appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Heat producing appliances. 3280.707... Systems § 3280.707 Heat producing appliances. (a) Heat-producing appliances and vents, roof jacks and... appliance, the heating appliance shall be installed by the manufacturer of the manufactured home in...

  2. Clinical evaluation of periodontal health during orthodontic treatment with fixed appliances

    Directory of Open Access Journals (Sweden)

    Hănțoiu T.

    2014-12-01

    Full Text Available Objectives: Fixed orthodontic appliances make daily application of oral hygiene standard procedures more difficult and in time may lead to accumulation of oral biofilms and development of gingivitis and hyperplasia. The aim of the study is to evaluate the periodontal health expressed by clinical indices in patients under orthodontic treatment with fixed appliances, according to different oral hygene maintenance programs. Material and method: We performed a randomized prospective study on 60 patients with fixed orthodontic appliances (17-25 years of age devided in three study groups. The clnical indices recorded were: modified gingival index, plaque index and sulcular bleeding index. Statistical analysis or the results were carried out using Student t test. Results: The patients were randomly divided into three groups: group A-patients were instructed to use electric brush, water flosser and interdental brush, group B- electric brush, interdental brush and fluoride and group C- manual brushing and fluoride. Statistical comparison of the values of the indexes with the Student t test for independent samples showed statistically significant differences in all three groups of patients studied between initial and final values of all recorded clinical parameters. Conclusions: Fixed orthodontics do not induce periodontal disease if basic principles of oral hygiene are followed in compliant patients, which are correctly instructed to deal with real challenge, represented by complete elimination of debris and bacterial accumulation.

  3. Exposure from Appliances (invited paper)

    Energy Technology Data Exchange (ETDEWEB)

    Cartwright, R.A

    1999-07-01

    The dosemeter studies on exposures to ELF electromagnetic irradiation from domestic equipment all suggest the whole-body doses are low, whilst some exposure to extremities could be high but of brief duration. Old style electric overblankets, however, are an exception and produce high fields and relatively high whole-body doses if switched on during the night. Relatively few epidemiological studies have addressed these issues. All of the studies have associated problems of interpretations. Two isolated studies throw up on association with the frequency of spontaneous abortion and electric blanket use whilst another links adult AML and electric shaver usage. Both results could be fortuitous. More consistency appears from three studies of childhood leukaemia. Here statistically significant associations between electric blanket use in pregnancies appear in two separate studies, as does hair dryer use in the case of children: other appliances use associations have been reported. These results are critically assessed. The United Kingdom Childhood Cancer Study (UKCCS) addresses some of these issues as part of a wider ranging assessment of EMF at home and at school. External sources are incorporated with the measurement of domestic ambient conditions in an attempt to make an overall assessment of total exposure. (author)

  4. Electrical Appliances and other Equipment

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    2006-01-01

    After some reflection on the efficiency concept, the paper first outlines how the most important electrical end-use technologies, used in households as well as in many service institutions, can be designed to consume much less energy than they do today. This is based on techno-physical analyses...... combined with some consideration on the future human need for the energy service output from the technologies. On the above basis is suggested one set of energy services, which a family in a cold climate can enjoy from just annually consuming 250 kWh of electricity per person. This is actually sufficient......-use technologies, are here suggested progressive electricity taxes, followed by critical reflections on the use of energy suppliers to promote selling less energy. Finally are suggested how research can be most effective and useful by being more interdisciplinary and less dependent on business interests...

  5. The Design, Construction, and Experimental Evaluation of a Compact Thermoacoustic-Stirling Engine Generator for Use in a micro-CHP Appliance

    Science.gov (United States)

    Wilcox, Douglas A., Jr.

    Micro combined heat and power or micro-CHP is the simultaneous generation of useful heat and electricity on a residential scale. The heat and electricity are produced at the point of use, avoiding the distribution losses associated with a centralized power plant. These appliances combine a conventional gas-fired condensing boiler with an electric power module capable of generating electricity from the heat of combustion. Currently, the leading power modules for micro-CHP appliances are free-piston Stirling engines (FPSEs) which can generate 1050 watts of electricity at a thermal-to-electric efficiency of 26%.[1] These external combustion engines have been under development for the last 25 years, with FPSE micro-CHP appliances only recently being introduced to the commercial market. Publications by developers assert unlimited service life and high efficiency, with low noise and emissions; but despite these claims, the actual reliability and cost of manufacturing has prevented their successful mass-market adoption. A Thermoacoustic-Stirling Engine Generator or TaSEG is one possible alternative to FPSE's. A TaSEG uses a thermoacoustic engine, or acoustic heat engine, which can efficiently convert high temperature heat into acoustic power while maintaining a simple design with fewer moving parts than traditional FPSE's. This simpler engine is coupled to an electrodynamic alternator capable of converting acoustic power into electricity. This thesis outlines the design, construction, and experimental evaluation of a TaSEG which is appropriate for integration with a gas burner inside of a residential micro- CHP appliance. The design methodology is discussed, focusing on how changes in the geometry affected the predicted performance. Details of its construction are given and the performance of the TaSEG is then outlined. The TaSEG can deliver 132 watts of electrical output power to an electric load with an overall measured thermal-to-electric (first law) efficiency of eta

  6. Energy efficient appliance choice under the EU labeling scheme

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Bradford F.; Schleich, Joachim [Fraunhofer-Institut fuer System- und Innovationsforschung (ISI), Karlsruhe (Germany)

    2010-02-15

    This paper extends the existing empirical literature on consumers' choices when exposed to energy labeling schemes by allowing choices to depend on household socio-economic characteristics, technology-related factors, behavioral and motivational factors, and country conditions in a multi-country analysis. To account for a possible knowledge-based selection bias, the econometric model distinguishes label class knowledge from the energy class choice decision. As a general finding, most covariates show stronger relationships with knowledge of labeling class than with the choice of energy efficiency class. Four factors show particularly strong and expected influences on label class awareness. First, general awareness of household energy use and energy saving technologies spills over into awareness of the energy class of specific appliances. Second, socioeconomic characteristics mater, as education increases label class awareness and older age reduces awareness. Third, economic incentives matter, as stated economic importance of energy saving and higher country electricity prices both generate greater label awareness. By contrast, stated concerns about global warming do not appear to have a broad impact on awareness. Fourth, effective country implementation of the labeling scheme raises label awareness. More surprisingly, most factors that promote awareness of appliance energy classes have a limited influence on actual appliance energy class choice. Efficient energy behavior in the household is not strongly linked to appliance energy class choice. Socio-economic characteristics also have limited influence. This finding is inline with other studies that find that household socio-economic characteristics have relatively weak associations with the adoption of energy efficient technologies (Mills and Schleich 2010, Brohmann et al. 2009). In fact, with education it is vocational degrees rather than university degrees that are positively associated with the propensity to

  7. Metal release from simulated fixed orthodontic appliances.

    Science.gov (United States)

    Hwang, C J; Shin, J S; Cha, J Y

    2001-10-01

    Most orthodontic appliances and archwires are stainless steel or nickel-titanium (NiTi) alloys that can release metal ions, with saliva as the medium. To measure metal released from the fixed orthodontic appliances currently in use, we fabricated simulated fixed orthodontic appliances that corresponded to half of the maxillary arch and soaked them in 50 mL of artificial saliva (pH 6.75 +/- 0.15, 37 degrees C) for 3 months. We used brackets, tubes, and bands made by Tomy (Tokyo, Japan). Four groups were established according to the appliance manufacturer and the type of metal in the .016 x .022-in archwires. Groups A and B were stainless steel archwires from Ormco (Glendora, Calif) and Dentaurum (Ispringen, Germany), respectively, and groups C and D were both NiTi archwires with Ormco's copper NiTi and Tomy's Bioforce sentalloy, respectively. Stainless steel archwires were heat treated in an electric furnace at 500 degrees C for 1 minute and quenched in water. We measured the amount of metal released from each group by immersion time. Our conclusions were as follows: (1) there was no increase in the amount of chromium released after 4 weeks in group A, 2 weeks in group B, 3 weeks in group C, and 8 weeks in group D; (2) there was no increase in the amount of nickel released after 2 weeks in group A, 3 days in group B, 7 days in group C, and 3 weeks in group D; and (3) there was no increase in the amount of iron released after 2 weeks in group A, 3 days in group B, and 1 day in groups C and D. In our 3-month-long investigation, we saw a decrease in metal released as immersion time increased.

  8. Consumer’s Attitude Towards Investments in Residential Energy-Efficient Appliances: How End-User Choices Contribute to Change Future Energy Systems

    DEFF Research Database (Denmark)

    Baldini, Mattia; Trivella, Alessio; Wente, Jordan William Halverson

    2017-01-01

    conventional and environmentally friendly alternatives when purchasing new household electric appliances. This study employs empirical data from a survey conducted by the Danish Energy Agency to model the decision criteria behind Danish consumer investment in energy-efficient labeled appliances. The analysis...... uses logistic regression over a set of socioeconomic, demographic, and behavioral variables to predict purchase propensities. The findings are relevant for policy makers interested in targeting consumers in the appliance market, particularly for a relatively wealthy national context. The study...

  9. Consumer knowledge and electricity consumption

    Energy Technology Data Exchange (ETDEWEB)

    Crawshaw, A J.E.; Williams, D I; Crawshaw, C M

    1985-12-01

    Householders in all-electric homes were asked to rank their electrical appliances in terms of annual running cost. By comparing this with an individually calculated correct order, an assessment of their knowledge was made. On this measure overall knowledge was good, but half the sample underestimated the running costs of key high-energy using appliances (space heating, hot-water, cooking). This specific lack of knowledge is critical, and was found to be correlated with higher bills. 16 references.

  10. Our Lives with Electric Things

    DEFF Research Database (Denmark)

    Schick, Lea

    2017-01-01

    Our lives with electric things are positively charged with meaning. Our bodies pulse with electrical activity. The electric appliances, devices, and technologies around us bring hope and anxiety, possibility and danger. Some have transformed our possibilities for reproducing, nurturing, and susta......Our lives with electric things are positively charged with meaning. Our bodies pulse with electrical activity. The electric appliances, devices, and technologies around us bring hope and anxiety, possibility and danger. Some have transformed our possibilities for reproducing, nurturing......, and sustaining life. Some mediate human sociality across time and space, while others knit ecological and interspecies relationships together. Still others create possibilities for controlling, managing, exploiting, and ending life. Against this backdrop any anthropology of electricity seems to require electric...... things. Can we still imagine the possibility of lives without electric things? Can electric things help us to address the possibilities and limits of life with electricity? Can our lives with electricity ever be disentangled from electric things? What are the unique capacities and material politics...

  11. Oral appliances and functional orthopaedic appliances for obstructive sleep apnoea in children.

    Science.gov (United States)

    Carvalho, Fernando R; Lentini-Oliveira, Débora A; Prado, Lucila Bf; Prado, Gilmar F; Carvalho, Luciane Bc

    2016-10-05

    Apnoea is a breathing disorder marked by the absence of airflow at the nose or mouth. In children, risk factors include adenotonsillar hypertrophy, obesity, neuromuscular disorders and craniofacial anomalies. The most common treatment for obstructive sleep apnoea syndrome (OSAS) in childhood is adeno-tonsillectomy. This approach is limited by its surgical risks, mostly in children with comorbidities and, in some patients, by recurrence that can be associated with craniofacial problems. Oral appliances and functional orthopaedic appliances have been used for patients who have OSAS and craniofacial anomalies because they hold the lower jaw (mandible) forwards which potentially enlarges the upper airway and increases the upper airspace, improving the respiratory function. To assess the effects of oral appliances or functional orthopaedic appliances for obstructive sleep apnoea in children. We searched the following electronic databases: Cochrane Oral Health's Trials Register (to 7 April 2016); Cochrane Central Register of Controlled Trials (CENTRAL; 2016, Issue 3) in the Cochrane Library (searched 7 April 2016); MEDLINE Ovid (1946 to 7 April 2016); Embase Ovid (1980 to 7 April 2016); LILACS BIREME (from 1982 to 7 April 2016); BBO BIREME (from 1986 to 7 April 2016) and SciELO Web of Science (from 1997 to 7 April 2016). We searched ClinicalTrials.gov and the World Health Organization International Clinical Trials Registry Platform for ongoing trials on 7 April 2016. We placed no restrictions on the language or date of publication when searching the electronic databases. All randomised or quasi-randomised controlled trials comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children 15 years old or younger. reduction of apnoea to less than one episode per hour. dental and skeletal relationship, sleep parameters improvement, cognitive and phonoaudiological function, behavioural problems, quality of life, side effects

  12. Energy Efficiency: The Implementation of Minimum Energy Performance Standard (MEPS Application on Home Appliances for Residential

    Directory of Open Access Journals (Sweden)

    Rahman K.A

    2016-01-01

    Full Text Available Generally, Minimum Energy Performance Standard (MEPS has been widespread across the country especially developed country. However, most consumers do not even know about the MEPS. Without sufficient knowledge, much energy have been wasted before this. The aim of this study is to review the implementation of MEPS of Asia country and to compare electricity consumption of home appliances with star rating and without star rating. In order to fulfil the objectives of the study, the equipment must be chosen correctly and must be learned properly. The home appliances that will be used also need to be chosen so that the comparison between the appliances will be matched correctly. To understand the results, the analysis was done using graphs and table. The purpose of using graph and table is to understand the comparison between appliances more clearly. The results show that home appliances with MEPS is more efficient on energy saving rather than without MEPS. This is the evidence as a method to educate a consumer on energy saving.

  13. Cephalometric effects of the Jones Jig appliance followed by fixed appliances in Class II malocclusion treatment.

    Science.gov (United States)

    Patel, Mayara Paim; Henriques, José Fernando Castanha; Freitas, Karina Maria Salvatore; Grec, Roberto Henrique da Costa

    2014-01-01

    The aim of this study was to cephalometrically assess the skeletal and dentoalveolar effects of Class II malocclusion treatment performed with the Jones Jig appliance followed by fixed appliances. The sample comprised 25 patients with Class II malocclusion treated with the Jones Jig appliance followed by fixed appliances, at a mean initial age of 12.90 years old. The mean time of the entire orthodontic treatment was 3.89 years. The distalization phase lasted for 0.85 years, after which the fixed appliance was used for 3.04 years. Cephalograms were used at initial (T1), post-distalization (T2) and final phases of treatment (T3). For intragroup comparison of the three phases evaluated, dependent ANOVA and Tukey tests were used. Jones Jig appliance did not interfere in the maxillary and mandibular component and did not change maxillomandibular relationship. Jones Jig appliance promoted distalization of first molars with anchorage loss, mesialization and significant extrusion of first and second premolars, as well as a significant increase in anterior face height at the end of treatment. The majority of adverse effects that occur during intraoral distalization are subsequently corrected during corrective mechanics. Buccal inclination and protrusion of mandibular incisors were identified. By the end of treatment, correction of overjet and overbite was observed. Jones Jig appliance promoted distalization of first molars with anchorage loss represented by significant mesial movement and extrusion of first and second premolars, in addition to a significant increase in anterior face height.

  14. 49 CFR 173.219 - Life-saving appliances.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

  15. Multi-objective demand side scheduling considering the operational safety of appliances

    International Nuclear Information System (INIS)

    Du, Y.F.; Jiang, L.; Li, Y.Z.; Counsell, J.; Smith, J.S.

    2016-01-01

    Highlights: • Operational safety of appliances is introduced in multi-objective scheduling. • Relationships between operational safety and other objectives are investigated. • Adopted Pareto approach is compared with Weigh and Constraint approaches. • Decision making of Pareto approach is proposed for final appliances’ scheduling. - Abstract: The safe operation of appliances is of great concern to users. The safety risk increases when the appliances are in operation during periods when users are not at home or when they are asleep. In this paper, multi-objective demand side scheduling is investigated with consideration to the appliances’ operational safety together with the electricity cost and the operational delay. The formulation of appliances’ operational safety is proposed based on users’ at-home status and awake status. Then the relationships between the operational safety and the other two objectives are investigated through the approach of finding the Pareto-optimal front. Moreover, this approach is compared with the Weigh and Constraint approaches. As the Pareto-optimal front consists of a set of optimal solutions, this paper proposes a method to make the final scheduling decision based on the relationships among the multiple objectives. Simulation results demonstrate that the operational safety is improved with the sacrifice of the electricity cost and the operational delay, and that the approach of finding the Pareto-optimal front is effective in presenting comprehensive optimal solutions of the multi-objective demand side scheduling.

  16. Turning the appliance market around towards A++

    Energy Technology Data Exchange (ETDEWEB)

    Noergaard, Joergen S.; Guldbrandsen, Tom [Dept. of Civil Engineering, Technical Univ. of Denmark (Denmark); Brange, Birgitte; Karbo, Peter [Elsparefonden (Denmark)

    2007-07-01

    In an effort to exploit better the labelling schemes for appliances the Danish Electricity Saving Trust has run some campaigns on cold appliances. In 1999 focus was on getting people to choose A-rated models, the 2004 campaign focussed on A+, and in 2005 on A++. These campaigns and their results are described in the paper and some conclusions are drawn.The campaigns have consisted of various elements, namely 1) a general information about the campaigns, 2) a subsidy offered temporarily during some months to people buying the A, A+ and A++ models, 3) a website where people can easily find the most energy efficient model within their specification, and 4) in the website are also listed the shops, where consumers can get the appliances at lowest prices. The latter was the most innovative and maybe also the most effective measure in the package.Results showed up as a permanent U-turn of the market in the course of a few years. Where models C, D, E earlier dominated the market, the A, A+ and A++, came to dominate as the standard models in stock. Consequently, their prices dropped significantly. The theory of a rational market behavior is based on some assumptions, one being that full information is available to all actors. The website identifying to the consumers the shops with the lowest priced efficient models was a step in that direction, and the result did not fail to turn up.

  17. Effects of mandibular protraction appliance associated to fixed appliance in adults

    Directory of Open Access Journals (Sweden)

    Bruno D'Aurea Furquim

    2013-10-01

    Full Text Available OBJECTIVE: This retrospective study aimed to conduct a cephalometric evaluation of the skeletal, dental and soft tissue effects resulting from treatment of adult patients presenting Class II malocclusion, performed with a Mandibular Protraction Appliance (MPA combined with a fixed orthodontic appliance. METHODS: The sample consisted of teleradiographs obtained before and after treatment of 9 adult patients (initial mean age of 22.48 years with bilateral Class II, division 1, malocclusion. Paired t test (p < 0.05 was applied to compare initial and final values. RESULTS: t test revealed an increase in anteroinferior facial height and posterior facial height. The dental changes include: extrusion of upper incisors, buccal inclination, protrusion of lower incisors, mesialization and extrusion of mandibular molars. Regarding the soft tissue component, there was an increase in nasolabial angle in addition to upper lip retrusion. CONCLUSIONS: The effects of treating Class II malocclusion adult patients, by means of using Mandibular Protraction Appliance (MPA combined with a fixed appliance were mostly observed in the mandibular arch, and consisted of buccal inclination, protrusion and intrusion of incisors, and mesialization and extrusion of the molars.

  18. One watt initiative: A global effort to reduce leaking electricity

    International Nuclear Information System (INIS)

    Meier, Alan K.; LeBot, Benoit

    1999-01-01

    Many domestic appliances and commercial equipment consume some electric power when they are switched off or not performing their primary purpose. The typical loss per appliance is low (from 1 to 25 W) but, when multiplied by the billions of appliances in houses and in commercial buildings, standby losses represent a significant fraction of total electricity use. Several initiatives to reduce standby losses have appeared in different parts of the world. One proposal, the 1-watt plan, seeks to harmonize these initiatives by establishing a single target for all appliances. This paper explains the background to the 1-watt plan, identifies some unresolved aspects, and gives some estimates of energy savings

  19. The Determination of Load Profiles and Power Consumptions of Home Appliances

    Directory of Open Access Journals (Sweden)

    Fatih Issi

    2018-03-01

    Full Text Available In recent years, the increment of distributed electricity generation based on renewable energy sources and improvement of communication technologies have caused the development of next-generation power grids known as smart grids. The structures of smart grids have bidirectional communication capability and enable the connection of energy generated from distributed sources to any point on the grid. They also support consumers in energy efficiency by creating opportunities for management of power consumption. The information on power consumption and load profiles of home appliances is essential to perform load management in the dwelling accurately. In this study, the power consumption data for all the basic home appliances, utilized in a two-person family in Çankırı, Turkey, was obtained with high resolution in one-second intervals. The detailed power consumption analysis and load profile were executed for each home appliance. The obtained data is not only the average power consumption of each appliance but also characterizes different operating modes or their cycles. In addition, the impact of these devices on home energy management studies and their standby power consumptions were also discussed. The acquired data is an important source to determine the load profile of individual home appliances precisely in home energy management studies. Although the results of this study do not completely reflect the energy consumption behavior of the people who live in this region, they can reveal the trends in load demands based on a real sample and customer consumption behavior of a typical two-person family.

  20. 24 CFR 3285.503 - Optional appliances.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Optional appliances. 3285.503... appliances. (a) Comfort cooling systems. When not provided and installed by the home manufacturer, any comfort cooling systems that are installed must be installed according to the appliance manufacturer's...

  1. 1992-1993 Bonneville Appliance Efficiency Program: Showerhead evaluation. Volume I - report

    Energy Technology Data Exchange (ETDEWEB)

    Warwick, W.M.

    1995-01-01

    The Bonneville Power Administration (Bonneville) provides wholesale electric power to over 100 retail distribution utilities in the Pacific Northwest. Bonneville is faced with meeting growing loads from these utilities. It acquires conservation as one means of meeting this load growth. Bonneville has offered a variety of conservation programs since 1980. Efficient showerheads have been a feature in residential conservation programs ever since. Bonneville launched the Residential Appliance Efficiency Program to focus on water-heater energy conservation opportunities in 1992. The Residential Appliance Efficiency Program consists of two parts, a water-heater efficiency program, and a hot-water efficiency program. This report evaluates the savings and costs of the first two years of the showerhead portion of the Residential Appliance Efficiency Program (the showerhead program). Although it is not a formal evaluation of the program limited to implementation or a {open_quotes}process{close_quotes} evaluation, observations about program design and implementation are included as appropriate. Results of this evaluation are limited to program participants within the Bonneville service territory.

  2. Refrigerator efficiency in Ghana: Tailoring an appliance market transformation program design for Africa

    International Nuclear Information System (INIS)

    Van Buskirk, Robert; Ben Hagan, Essel; Ofosu Ahenkorah, Alfred; McNeil, Michael A.

    2007-01-01

    In some cases, a simple replication of developed country appliance efficiency labels and standards may not be completely feasible in Ghana, Africa. Yet by creatively modifying the developed country appliance efficiency market transformation model, it should be possible to achieve dramatic energy use reductions. As was true in developed countries in the previous two decades, refrigeration efficiency improvements provide the greatest energy savings potential in the residential electricity sector in Ghana. Although Ghana, like many African countries may impose standards on imports since Ghana does not have manufacturing facilities for appliances in country. This approach may hurt some consumers who patronize a very diverse market of used appliances imported from Europe. We discuss how meeting the challenges of the Ghanaian market will require modification of the usual energy efficiency labeling and standards paradigm. But once a refrigerator market transformation is accomplished in Ghana, we estimate an average energy savings potential of 550 kWh/refrigerator/year, and a monetary savings of more than $35/refrigerator/year. We discuss how this modified refrigerator efficiency market transformation may occur in the Ghanaian context. If successful, this market transformation is likely to be an example for many other African countries

  3. Compliance with removable orthodontic appliances.

    Science.gov (United States)

    Shah, Nirmal

    2017-12-22

    Data sourcesMedline via OVID, PubMed, Cochrane Central Register of Controlled Trials, Web of Science Core Collection, LILACS and BBO databases. Unpublished clinical trials accessed using ClinicalTrials.gov, National Research Register, ProQuest Dissertation and Thesis database.Study selectionTwo authors searched studies from inception until May 2016 without language restrictions. Quantitative and qualitative studies incorporating objective data on compliance with removable appliances, barriers to appliance wear compliance, and interventions to improve compliance were included.Data extraction and synthesisQuality of research was assessed using the Cochrane Collaboration's risk of bias tool, the risk of bias in non-randomised studies of interventions (ROBINS-I), and the mixed methods appraisal tool. Statistical heterogeneity was investigated by examining a graphic display of the estimated compliance levels in conjunction with 95% confidence intervals and quantified using the I-squared statistic. A weighted estimate of objective compliance levels for different appliances in relation to stipulated wear and self-reported levels was also calculated. Risk of publication bias was assessed using funnel plots. Meta-regression was undertaken to assess the relative effects of appliance type on compliance levels.ResultsTwenty-four studies met the inclusion criteria. Of these, 11 were included in the quantitative synthesis. The mean duration of objectively measured wear was considerably lower than stipulated wear time amongst all appliances. Headgear had the greatest discrepancy (5.81 hours, 95% confidence interval, 4.98, 6.64). Self-reported wear time was consistently higher than objectively measured wear time amongst all appliances. Headgear had the greatest discrepancy (5.02 hours, 95% confidence interval, 3.64, 6.40). Two studies found an increase in compliance with headgear and Hawley retainers when patients were aware of monitoring. Five studies found younger age groups to

  4. Retrospective evaluation of appliance price trends

    International Nuclear Information System (INIS)

    Dale, Larry; Antinori, Camille; McNeil, Michael; McMahon, James E.; Sydny Fujita, K.

    2009-01-01

    Real prices of major appliances (refrigerators, dishwashers, heating and cooling equipment) have been falling since the late 1970s despite increases in appliance efficiency and other quality variables. This paper demonstrates that historic increases in efficiency over time, including those resulting from minimum efficiency standards, incur smaller price increases than were expected by the Department of Energy (DOE) forecasts made in conjunction with standards. This effect can be explained by technological innovation, which lowers the cost of efficiency, and by market changes contributing to lower markups and economies of scale in production of higher efficiency units. We reach four principal conclusions about appliance trends and retail price setting: 1.For the past several decades, the retail price of appliances has been steadily falling while efficiency has been increasing. 2.Past retail price predictions made by the DOE analyses of efficiency standards, assuming constant prices over time, have tended to overestimate retail prices. 3.The average incremental price to increase appliance efficiency has declined over time. DOE technical support documents have typically overestimated this incremental price and retail prices. 4.Changes in retail markups and economies of scale in production of more efficient appliances may have contributed to declines in prices of efficient appliances

  5. Multi-kanban mechanism for appliance disassembly

    Science.gov (United States)

    Udomsawat, Gun; Gupta, Surendra M.

    2005-11-01

    The use of household appliances continues to rise every year. A significant number of End-Of-Life (EOL) appliances are generated because of the introduction of newer models that are more attractive, efficient and affordable. Others are, of course, generated when they become non-functional. Many regulations encourage recycling of EOL appliances to reduce the amount of waste sent to landfills. In addition, EOL appliances offer the appliance manufacturing and remanufacturing industries a source of less expensive raw materials and components. For this reason product recovery has become a subject of interest during the past decade. In this paper, we study the disassembly line for appliance disassembly. We discuss and incorporate some of the complications that are inherent in disassembly line including product arrival, demand arrival, inventory fluctuation and production control mechanisms. We show how to overcome such complications by implementing a multi-kanban system in the appliance disassembly line setting. The multi-kanban system (MKS) relies on dynamic routing of kanbans according to the state of the system. We investigate the multi-kanban mechanism using simulation and explore the effect of product mix on performance of the traditional push system (TPS) and MKS in terms of controlling the system's inventory while attempting to achieve a decent customer service level.

  6. 24 CFR 3280.714 - Appliances, cooling.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Appliances, cooling. 3280.714... Systems § 3280.714 Appliances, cooling. (a) Every air conditioning unit or a combination air conditioning... accordance with ANSI Z21.40.1-1996, Gas Fired, Heat Activated, Air Conditioning and Heat Pump Appliances, and...

  7. 49 CFR 238.429 - Safety appliances.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances. 238.429 Section 238.429... Equipment § 238.429 Safety appliances. (a) Couplers. (1) The leading and the trailing ends of a semi... appliance mechanical strength and fasteners. (1) All handrails, handholds, and sill steps shall be made of 1...

  8. Minat Masyarakat dalam Menggunakan Smart Appliances

    Directory of Open Access Journals (Sweden)

    Diah Yuniarti

    2014-09-01

    Full Text Available Harga sumber energi yang semakin naik dari tahun ke tahun dan kemajuan teknologi telah mendorong perkembangan smart grid. Smart appliance merupakan salah satu komponen penting dalam smart grid. Penerapan smart appliance sejalan dengan kebijakan untuk mengurangi konsumsi energi, mengurangi emisi karbon dan penyediaan energi dari energi terbarukan. Penetrasi telepon bergerak turut memudahkan manajemen energi dan otomatisasi home appliance. Penelitian ini dilakukan untuk menganalisis minat masyarakat, yang merupakan aktor aktif dalam konsumsi dan manajemen energi di rumah tangga. Data penelitian dianalisis  dengan menggunakan metode structural equation modeling (SEM Hasil penelitian menunjukkan bahwa variabel enjoyment memiliki pengaruh yang signifikan terhadap minat dalam menggunakan smart appliance. Sedangkan, variabel compatibility ease of use, relative advantage dan image tidak memiliki pengaruh yang signifikan terhadap minat menggunakan smart appliance.

  9. Okanagan indoor wood burning appliance inventory survey

    International Nuclear Information System (INIS)

    2001-01-01

    A survey was conducted to determine the usage and nature of wood burning appliances used by residents in British Columbia's Okanagan region. The objective was to better understand this source of air quality concern and to facilitate strategic planning, guidelines and legislation. The survey also provides a baseline to track the effectiveness of any reduction strategies. It identifies the different types of wood burning appliances used in the community and presents residential options about potential bylaws to protect air quality. The receptivity of households to switch to more efficient wood burning appliances was also examined. The survey completes a portion of an overall emissions inventory for the Okanagan Valley. Environment Canada uses the particulate loading results to model the air quality in the airshed. Results showed that approximately 21 per cent of the households in the Okanagan use indoor wood burning appliances, and burn an average of 2.3 cords of wood each year. Only 11 per cent of the appliances are considered to have advanced burning technology. It is projected that the use of wood burning appliances in the Okanagan will increase by 5 to 7 per cent in the next 2 years. Most residents have good burning habits, but some improvements can still be made. Many residents are considering exchanging old wood burning appliances for clean burning technology appliances for environmental and health reasons. Most households would support a bylaw to control nuisance amounts of smoke from wood burning appliances. 20 tabs., 5 figs

  10. On the necessity of improving the environmental impacts of furniture and appliances in net-zero energy buildings.

    Science.gov (United States)

    Hoxha, Endrit; Jusselme, Thomas

    2017-10-15

    There is now clear evidence regarding the extensive use of furniture and appliances in daily human life, but there is less evidence of their impact on the environment. Responding to this gap in knowledge, this study focuses on an assessment of the environmental impacts of furniture and appliances as used in highly energy efficient buildings. Their primary energy, non-renewable energy and global warming potential indicators have been assessed by extending the boundaries of the Life Cycle Assessment (LCA) study beyond the building itself. In conclusion, we found that furniture and appliances were responsible for around 30% of greenhouse gas emissions and non-renewable energy consumption and 15% of primary energy consumption comparing to the overall impacts of the building. Since embodied impacts represent the largest values, the process for labelling the appliances' energy efficiency should encompass a life-cycle point of view, not just a usage point of view as the case currently. Among office appliances, computer equipment was ranked as the highest impacting element, especially laptops and monitors. As for domestic appliances, refrigerators and electric ovens had the biggest impacts. Concerning furniture, the greatest impacts were from office and kitchen cabinets. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Household electricity demand profiles

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Heiselberg, Per Kvols; Larsen, Olena Kalyanova

    2016-01-01

    Highlights •A 1-min resolution household electricity load model is presented. •Model adapts a bottom-up approach with single appliance as the main building block. •Load profiles are used to analyse the flexibility potential of household appliances. •Load profiles can be applied in other domains, .......g. building energy simulations. •The demand level of houses with different number of occupants is well captured....

  12. A research project to encourage system-compatible design of end-use appliances

    International Nuclear Information System (INIS)

    Dorr, D.; Key, T.; Sitzlar, G.

    1995-01-01

    Cooperative system compatibility research sponsored by the Canadian Electrical Association (CEA) and the Electric Power Research Institute (EPRI) for improving appliance performance deficiencies was described. Power producer and end-user compatibility concerns was addressed through the development of a System Compatibility Research Project. A list of project tasks was provided. The CEA and EPRI initiated a project to establish flicker response of various lighting systems, which included physical tests. Results of this project were presented and discussed. The incentives for developing switch mode power supplies with enhanced immunity to voltage fluctuations and short interruptions was discussed. It was concluded that power quality studies currently underway will provide designers with a profile of the expected utility environment for their products. System compatibility research will identify areas that should be addressed by standards bodies so that designers can apply applicable criteria objectives early in the appliance design process. These efforts were expected to encourage appropriate manufacturer criteria for compatibility by convincing buyers and sellers that there is a real pay back for this investment. 13 refs., 6 figs., 4 tabs

  13. The International Database of Efficient Appliances (IDEA): A new tool to support appliance energy-efficiency deployment

    International Nuclear Information System (INIS)

    Gerke, Brian F.; McNeil, Michael A.; Tu, Thomas

    2017-01-01

    Highlights: •IDEA collects, organizes, and stores data on appliance features and efficiency. •Data can be gathered for any appliance type on any international market. •IDEA enables new approaches to efficiency deployment and monitoring. •Techniques are developed for cross-market comparison of energy-savings potential. •We find significant cost-effective energy-savings potential from efficiency for Indian and Chinese refrigerators. -- Abstract: Appliance energy-efficiency programs are a central component of many countries’ energy-policy portfolios. A major barrier to optimal implementation of these programs is lack of data to determine market baselines, assess the potential for cost-effective energy savings, and track markets over time to evaluate and verify program impacts. To address this gap, we have developed the International Database of Efficient Appliances (IDEA), a suite of software tools that automatically gathers data that is currently dispersed across various online sources and compiles it into a unified repository of information on efficiency, price, and features for a diversity of appliances and devices in markets around the world. In this article we describe the framework and functionality of IDEA, and we demonstrate its power as a resource for research and policy development related to appliance energy efficiency. Using IDEA data for refrigerators in China and India, we assess the potential for cost-effective energy savings within each market by computing robust indicators that can also be easily compared across different appliances and markets. We find that significant cost-effective savings are available on both markets. We discuss implications for the development of future energy-efficiency deployment programs.

  14. Miscellaneous electricity use in U.S. homes

    International Nuclear Information System (INIS)

    Sanchez, Marla C.; Koomey, Jonathan G.; Moezzi, Mithra M.; Meier, Alan; Huber, Wolfgang

    1999-01-01

    Historically, residential energy and carbon saving efforts have targeted conventional end uses such as water heating, lighting and refrigeration. The emergence of new household appliances has transformed energy use from a few large and easily identifiable end uses into a broad array of ''miscellaneous'' energy services. This group of so called miscellaneous appliances has been a major contributor to growth in electricity demand in the past two decades. We use industry shipment data, lifetimes, and wattage and usage estimates of over 90 individual products to construct a bottom-up end use model (1976-2010). The model is then used to analyze historical and forecasted growth trends, and to identify the largest individual products within the miscellaneous end use. We also use the end use model to identify and analyze policy priorities. Our forecast projects that over the period 1996 to 2010, miscellaneous consumption will increase 115 TWh, accounting for over 90 percent of future residential electricity growth. A large portion of this growth will be due to halogen torchiere lamps and consumer electronics, making these two components of miscellaneous electricity a particularly fertile area for efficiency programs. Approximately 20 percent (40 TWh) of residential miscellaneous electricity is ''leaking electricity'' or energy consumed by appliances when they are not performing their principal function. If the standby power of all appliances with a standby mode is reduced to one watt, the potential energy savings equal 21 TWh/yr, saving roughly$1-2 billion annually

  15. 78 FR 25724 - Petition for Waiver of GE Appliances From the Department of Energy Residential Refrigerator and...

    Science.gov (United States)

    2013-05-02

    ... refrigerators and refrigerator-freezers that are the focus of this notice.\\1\\ Part B includes definitions, test... division of General Electric Co., (``GE'') is a leading manufacturer and marketer of household appliances...

  16. The flexibility of household electricity demand over time

    International Nuclear Information System (INIS)

    Halvorsen, B.; Larsen, B.M.

    2001-01-01

    Empirical estimates of long run effects on residential electricity demand from changes in the electricity price are usually estimated by cross-sectional variation in the current stock of electric household appliances across households at a certain point in time. Here, we use a discrete-continuous approach modeling the long run effects by investments in new appliances. We apply the annual Norwegian Survey of Consumer Expenditure for the period 1975 to 1994 to estimate the short and long run own price elasticities in the two approaches. We find the estimated long run elasticity only slightly more price elastic than the short run. We also find that the long run elasticity does not differ significantly between the two approaches. The reason for both results is that, since there is no alternative source of energy for these appliances, there are no substitution effects

  17. 46 CFR 199.70 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Personal lifesaving appliances. 199.70 Section 199.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS... appliances. (a) Lifebuoys. Each vessel must carry lifebuoys approved under approval series 160.150 as follows...

  18. Microbiologically influenced corrosion of orthodontic metallic appliances.

    Science.gov (United States)

    Kameda, Takashi; Oda, Hirotake; Ohkuma, Kazuo; Sano, Natsuki; Batbayar, Nomintsetseg; Terashima, Yukari; Sato, Soh; Terada, Kazuto

    2014-01-01

    Biocorrosion (microbiologically influenced corrosion; MIC) occur in aquatic habitats varying in nutrient content, temperature, stress and pH. The oral environment of organisms, including humans, should be one of the most hospitable for MIC. Corrosion of metallic appliances in the oral region is one cause of metal allergy in patients. In this study, an inductively coupled plasma-optical emission spectrometer revealed elution of Fe, Cr and Ni from stainless steel (SUS) appliances incubated with oral bacteria. Three-dimensional laser confocal microscopy also revealed that oral bacterial culture promoted increased surface roughness and corrosion pits in SUS appliances. The pH of the supernatant was lowered after co-culture of appliances and oral bacteria in any combinations, but not reached at the level of depassivation pH of their metallic materials. This study showed that Streptococcus mutans and Streptococcus sanguinis which easily created biofilm on the surfaces of teeth and appliances, did corrode orthodontic SUS appliances.

  19. Documentation of Appliances & Interaction Devices

    DEFF Research Database (Denmark)

    2004-01-01

    The interaction devices and appliances explored in the WorkSPACE project, address spatial computing in the context of work. We have developed and explored a range of appliances and interaction devices. The scope has been to develop tools for support of collaboration by mixing digital and physical...

  20. Prediction of appliances energy use in smart homes

    International Nuclear Information System (INIS)

    Arghira, Nicoleta; Hawarah, Lamis; Ploix, Stéphane; Jacomino, Mireille

    2012-01-01

    This paper presents methods for prediction of energy consumption of different appliances in homes. The aim is to predict the next day electricity consumption for some services in homes. Historical data for a set of homes in France was used. Two basic predictors are tested and a stochastic based predictor is proposed. The performance of the predictors is studied and it shows that the proposed predictor gives better results than other approaches. Two processings are proposed to improve the performance of the predictor, segmentation and aggregation of data. Application results are provided.

  1. Technical and legal application possibilities of the compulsory labelling of the standby consumption of electrical household and office appliances - Project No. 53/03. Final report for the Federal Ministry of Economics and Labour; Technische und rechtliche Anwendungsmoeglichkeiten einer verpflichtenden Kennzeichnung des Leerlaufverbrauchs strombetriebener Haushalts- und Buerogeraete - Dienstleistungsvorhaben Nr. 53/03. Abschlussbericht an das Bundesministerium fuer Wirtschaft und Arbeit

    Energy Technology Data Exchange (ETDEWEB)

    Schlomann, B.; Cremer, C.; Friedewald, M. [Fraunhofer-Institut fuer Systemtechnik und Innovationsforschung, Karlsruhe (DE)] (and others)

    2005-04-27

    The standby consumption of electrical households and office appliances continues to be significant world-wide since the number of products with standby componen ts is constantly increasing. For Germany, a recent assessment of the Fraunhofer ISI (Cremer et al. 2003) for 2001 arrived at an electricity demand of almost 15 TWh for household and office appliances in standby mode. i.e. in standby and off -mode. This represents almost 40% of the total consumption of these appliances and around 3% of the total electricity demand of the final energy sectors in Ge rmany. The standby share in electricity demand is over 80 or even 90% for numer ous appliances. The Federal Environmental Agency calculated that every year stan dby losses in German households and offices are responsible for wasted electrici ty amounting to 3.5 billion Euro (UBA 2004). For the OECD countries, field studi es show that between 3 and 13% of the electricity consumption of households can be ascribed to standby losses (IEA 2001). Without energy policy measures on bot h national and international levels, there is a great risk that a further increa se in standby consumption will occur. Many studies dealing with this subject hav e already been conducted and have shown that low standby consumption is technica lly feasible and usually achievable at a reasonable cost. One possible energy po licy measure to reduce the standby consumption of electrical household and offic e appliances is the introduction of mandatory consumption labelling. In principl e, a high degree of effectiveness is attributed to such regulatory/command-and-c ontrol measures with regard to influencing the energy efficiency of devices. Com pulsory energy labels to identify and, where necessary, to classify electricity consumption produce greater market transparency and offer buyers an additional d ecision criterion. In this way they promote indirectly the development, producti on and supply of energy-efficient products. When combined with

  2. 46 CFR 195.06-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 195.06-1 Section... VESSELS VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Lifesaving Appliances and Arrangements § 195.06-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be...

  3. Crew appliance study

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Viable crew appliance concepts were identified by means of a thorough literature search. Studies were made of the food management, personal hygiene, housekeeping, and off-duty habitability functions to determine which concepts best satisfy the Space Shuttle Orbiter and Modular Space Station mission requirements. Models of selected appliance concepts not currently included in the generalized environmental-thermal control and life support systems computer program were developed and validated. Development plans of selected concepts were generated for future reference. A shuttle freezer conceptual design was developed and a test support activity was provided for regenerative environmental control life support subsystems.

  4. Fibrotic encapsulation of orthodontic appliance in palate.

    Science.gov (United States)

    Muthu, Jananni; Muthanandam, Sivaramakrishnan; Umapathy, Gubernath; Kannan, Anitha Logaranjani

    2017-01-01

    Iatrogenic trauma though not serious is very common in dental practice. Orthodontic treatment can inflict such injuries as they are prolonged over a long period of time. Ill-fabricated orthodontic appliances, such as wires and brackets, or the patients' habits such as application of constant pressure over the appliance can traumatize the adjacent oral soft tissues. In rare cases, these appliances can get embedded into the mucosa and gingival tissues. This case report describes one such case of iatrogenic trauma to the palatal mucosa due to entrapment of a tongue spike appliance and its surgical management.

  5. 46 CFR 188.27-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 188.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 188.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements shall be in accordance with the requirements for...

  6. 46 CFR 90.27-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 90.27-1 Section... VESSELS GENERAL PROVISIONS Lifesaving Appliances and Arrangements § 90.27-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements must be in accordance with subchapter W (Lifesaving...

  7. 46 CFR 70.28-1 - Lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements. 70.28-1 Section... PROVISIONS Lifesaving Appliances and Arrangements § 70.28-1 Lifesaving appliances and arrangements. All lifesaving appliances and arrangements on passenger vessels must be in accordance with subchapter W...

  8. A comparative study of two-piece ostomy appliances.

    Science.gov (United States)

    Welser, Marion; Riedlinger, Inge; Prause, Ulla

    The quality of life of people with a stoma may be affected by peristomal skin disorders and by frequent unplanned changes of ostomy appliances due to problems with those appliances. The aim of this study was to evaluate two new, two-piece ostomy appliances with mechanical couplings (both from the SenSura range by Coloplast) and their ability to address areas that may be important to the quality of life of people with stomas, including appliance changes, stool seepage and overfilling. The study design featured two comparative, crossover, randomized multi-centre studies that were conducted in Germany. The SenSura appliances were evaluated against established reference appliances. Seventy-three individuals with a colostomy (closed-end appliances) and 75 individuals with an ileostomy (drainable appliances) participated in the studies. The participants tested 4-6 flanges of each type within a maximum period of two weeks. The results demonstrated that there was less seepage of stool observed under the SenSura flange when it was removed (pappliances. The SenSura flanges had better adhesion and flexibility and were easier to remove than the references (pappliances on quality of life indicators - there were fewer unplanned changes and less seepage of stool was observed in patients using the SenSura products.

  9. Designing, Building and Controlling of Home Appliances Unit Using PC

    Directory of Open Access Journals (Sweden)

    Saleh Ben Safar

    2017-12-01

    Full Text Available Smart home is a residential building that is usually new or modern equipped with necessary tools and wiring that enable its occupants to control a number of electrical devices and several household appliances through a suitable software. Recently, the development of home automation systems is accelerating rapidly as a result of the rapid intersection of modern technologies. Here we are talking about systems for home communication networks as well as entertainment, security, convenience, etc. These systems are controlled by sending signals through wires distributed throughout the house or Through wireless means to programmable keys or devices so that they understand these commands and deal with them as desired. In this paper, I will discuss how to design the circuit with appropriate components, build it in Printed Circuit Board and connect it to a personal computer by using programmable language in order to control all home appliances by just one click. 

  10. 38 CFR 17.150 - Prosthetic and similar appliances.

    Science.gov (United States)

    2010-07-01

    ... appliances. 17.150 Section 17.150 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.150 Prosthetic and similar appliances... appliances including invalid lifts and therapeutic and rehabilitative devices, and special clothing made...

  11. Evaluation of safety management in an Appliances manufacturing company

    Directory of Open Access Journals (Sweden)

    F. Golbabaei

    2015-01-01

    Full Text Available Introduction: Prevention of accidents and work related diseases, are not allowed regardless of the safety of employees, customers, contractors and other persons. Assessment of individual safety management activities could reduce many losses. Present study aimed to evaluate the safety management of a household appliance manufacturing company.  .Material and Method: This study has done in a household appliance manufacturing company in Damavand city. Two questionnaires were firstly designed based on the weighted scores. The questionnaire 1 consisted of 4 indicators: Safety of machinery, Electrical safety, Risk assessment and Fire safety. Questionnaire 2 consisted of 11 sub indicators. Both questionnaires were completed by 30 HSE experts and supervisors. Reliability of questionnaires was based on cronbachs alpha coefficient. the safety status of each unit was determined and scored using information acquired by the questionnaires. Lastly, the safety of the entire company was determined.  .Result: Results showed that in safety management: the pressing and store house were in a good range of 66.66 and 60.12 points. Powder painting, enameling, laboratory were in a average range of 56.25, 55.92 and 54.15 points. Assembling and door storage were in a week range of 46.06 points.  .Conclusion: The findings showed that the safety status in the studied appliances company is in average range with 55.45 points. Therefore, it is recommended that the safety indicators should be improved for the betterment of the safety management in the company.

  12. Mountain Plains Learning Experience Guide: Electrical Wiring. Course: Electrical Wiring Trim-Out.

    Science.gov (United States)

    Arneson, R.; And Others

    One of two individualized courses included in an electrical wiring curriculum, this course covers electrical materials installation for the trim-out stage. The course is comprised of five units: (1) Outlets, (2) Fixtures, (3) Switches, (4) Appliances, and (5) Miscellaneous. Each unit begins with a Unit Learning Experience Guide that gives…

  13. Energy efficiency and appliance purchases in Europe: Consumer profiles and choice determinants

    International Nuclear Information System (INIS)

    Gaspar, Rui; Antunes, Dalila

    2011-01-01

    This study seeks to the following: (1) understand the factors/characteristics typically considered when purchasing electrical appliances, (2) analyse the differences between consumer profiles regarding these and (3) understand the factors driving the consideration of energy efficiency class by purchasers. Results indicate a preference for first considering cost, followed by quality and energy consumption considerations. These are correlated positively with the consideration of energy efficiency class in consumer choices. Also, regression analysis shows environmental attitudes to be negative predictors of energy efficiency class consideration, while specific environmental behaviours were positive predictors. Finally, consumer profiles were identified based on gender, age and whether or not the purchaser was accompanied when decisions were made. Implications for retail employee training and the development of persuasive messages for consumers based on established profiles are discussed. - Highlights: → We assessed factors typically considered by consumers in electrical appliances choice. → Characteristics identified as most important for choice were as follows: cost, quality and energy consumption. → These correlated positively with the consideration of energy efficiency class. → Differences between consumer profiles regarding the characteristics consideration were identified. → Differences imply persuasive messages adaption to these, to increase energy class consideration.

  14. Equipment and appliances for underwater operations. Pt. 2

    International Nuclear Information System (INIS)

    Krueger, P.

    1976-01-01

    The 6/75 edition of 'mt' reported on the 'ARGE underwater appliances' and the study on 'design development of appliances and equipment for underwater use' in a brief summary. One of these designs, the 'unmanned DSWS underwater appliance' was described in detail. The present article describes three further design developments mentioned in the above study and which are based on unmanned appliances connected to the mother-ship. These designs were developed by Preussag-Meerestechnik. (orig.) [de

  15. Office management of obstructive sleep apnoea: appliances.

    Science.gov (United States)

    Johnson, Matthew D

    2015-08-01

    Oral appliances are becoming increasingly common in the treatment of obstructive sleep apnoea (OSA). They work by advancing the mandible and opening the pharynx. There are several types of devices available for use. Many patients intolerant to continuous positive airway pressure (CPAP) are using oral appliances for OSA. Oral appliances have been shown to improve polysomnography, quality of life and health measures associated with OSA. There is current work to better identify patients who are ideal candidates. Development of titratable devices and monitoring are optimizing usage. They have been compared with CPAP, with both showing improvement in OSA; however, CPAP remains superior overall. Oral appliances are becoming first-line therapy for mild and moderate OSA. They provide a meaningful alternative in severe OSA for patients unable to use CPAP. Device titration and usage monitoring are beginning to hone oral appliances as a therapeutic option.

  16. Residential electricity demand in Singapore

    International Nuclear Information System (INIS)

    Ang, B.W.; Goh, T.N.; Liu, X.Q.

    1992-01-01

    Residential electricity consumption in Singapore increased at a rate of 8.8% per year between 1972 and 1990. Estimates of the long-run income and price elasticities are 1.0 and -0.35, respectively. The energy-conservation campaigns that have been launched are found to have marginal effects on consumption. A statistical analysis shows that the consumption is sensitive to small changes in climatic variables, particularly the temperature, which is closely linked to the growing diffusion of electric appliances for environmental controls. There has been a temporal increase in the ownership levels of appliances associated with increasing household incomes. However, other factors were involved since the ownership levels would also increase over time after the elimination of the income effect. A large part of the future growth in electricity demand will arise from the growing need for air-conditioning, which will lead to increasingly large seasonal variations in electricity use. (author)

  17. Load Characterization for small domestic appliances and electronics

    NARCIS (Netherlands)

    Van der Sluis, P.

    2009-01-01

    In this report, the energy consumption of small domestic loads has been analysed. To make the around 100 types of appliances considereda bit manageable, the appliances were categorized into several groups. The possibilities for time-shifting of the energy use of these small appliances was

  18. DC Home Appliances for DC Distribution System

    Directory of Open Access Journals (Sweden)

    MUHAMMAD KAMRAN

    2017-10-01

    Full Text Available This paper strengthens the idea of DC distribution system for DC microgrid consisting of a building of 50 apartments. Since the war of currents AC system has been dominant because of the paucity of research in the protection of the DC system. Now with the advance research in power electronics material and components, generation of electricity is inherently DC as by solar PV, fuel cell and thermoelectric generator that eliminates the rectification process. Transformers are replaced by the power electronics buck-boost converters. DC circuit breakers have solved the protection problems for both DC transmission and distribution system. In this paper 308V DC microgrid is proposed and home appliances (DC internal are modified to operate on 48V DC from DC distribution line. Instead of using universal and induction motors in rotary appliances, BLDC (Brushless DC motors are proposed that are highly efficient with minimum electro-mechanical and no commutation losses. Proposed DC system reduces the power conversion stages, hence diminishes the associated power losses and standby losses that boost the overall system efficiency. So in view of all this a conventional AC system can be replaced by a DC system that has many advantages by cost as well as by performance

  19. Removable orthodontic appliances: new perspectives on capabilities and efficiency.

    Science.gov (United States)

    Hamid Zafarmand, A; Mahdi Zafarmand, M

    2013-06-01

    Removable appliances are a dependable choice for many patients but like all orthodontic appliances, they have some limitations in use. Patient selection and appropriate appliance design are two key factors for success. Many patients, especially adults, prefer intra-oral appliances to extra-oral devices. Sometimes a removable intra-oral appliance can solve a dental problem in a shorter period of time compared to fixed treatment, and this has also been repeatedly seen in molar distalisation. From the interceptive perspective, the appliance can prevent or alleviate an impending crowding for erupting permanent incisors. This article describes 5 patients with different orthodontic problems: impending crowding for erupting upper canine with 2 approaches, provision of space for upper cuspids, resolution of chronic attrition of anterior teeth, relief of space shortage for upper canines eruption, and reduction of excess overjet. All subjects were treated with removable appliances of various designs.

  20. Study of some aspects of the long-run domestic demand for electricity in New Zealand

    Energy Technology Data Exchange (ETDEWEB)

    Stent, A F

    1982-01-01

    This study investigates the long-run domestic demand for electricity in New Zealand over the period 1945 to 1972. The first part analyzes the ownership of electrical appliances using data from the five yearly censuses of population and dwellings. A dynamic appliance ownership model is developed for the analysis. This model explains the proportion of households, in small regional districts, with ownership status of a particular appliance type when observed at census time. It measures the effects of prices, income, and household taste characteristics on ownership. The main results include estimates of long-run electricity price effects. The second part of the thesis estimates dynamic demand equations for electricity. A flow-adjustment model is fitted to moving cross sections of data for individual Electrical Supply Authority districts in the North and South Islands separately. The final part of the thesis undertakes a synthesis of electricity price effects on appliance ownership (from the first part) and electricity demand (from the second part). This indicates substantial consistency in the estimates obtained. The main conclusions for electricity price are that this variable has been a significant factor in explaining the variation in domestic electricity consumption over the period; that the relationship has been inelastic in the later part, in both short and long-runs; and that long-run effects are mainly via the use of the electrical services.

  1. Optimal daily operation of a smart-household under dynamic pricing considering thermostatically and non-thermostatically controllable appliances

    NARCIS (Netherlands)

    Paterakis, N.G.; Medeiros, M.F.; Catalao, J.P.S.; Siaraka, A.; Bakirtzis, A.G.; Erdinc, O.

    2015-01-01

    In this study, a home energy management system structure is developed in order to determine the optimal commitment of a smart-household. Two types of loads are explicitly modeled: non-thermostatically controllable (electric vehicle, shiftable appliances) and thermostatically controllable loads (air

  2. 46 CFR 109.209 - Appliances for watertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 109.209 Section 109... OPERATIONS Tests, Drills, and Inspections § 109.209 Appliances for watertight integrity. (a) Before getting underway, the master or person in charge shall insure that each appliance for watertight integrity is...

  3. 42 CFR 409.14 - Supplies, appliances, and equipment.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Supplies, appliances, and equipment. 409.14 Section... Hospital Services § 409.14 Supplies, appliances, and equipment. (a) Except as specified in paragraph (b) of this section, Medicare pays for supplies, appliances, and equipment as inpatient hospital or inpatient...

  4. Preliminary Study of Perception and Consumer Behaviour Towards Energy Saving for Household Appliances: A Case of Makassar

    Science.gov (United States)

    Syam Akil, Yusri; Mangngenre, Saiful; Mawar, Sri; Amar, Kifayah

    2018-03-01

    Electricity load has tendency to increase over the time. Therefore, efforts to maintain a balance between electricity supply and demand such as increasing energy saving related to the use of home electricity appliances are urgently needed. In general, one of the household appliances which consumes relatively high electricity energy is refrigerator. The purpose of this study is to analyze residential consumers perceptions and their behaviours about electricity energy saving in relation to the usage of household appliances in Makassar, Indonesia particularly for refrigerator. Moreover, typical relationship between perceptions and consumers behaviours is also analyzed by composed two regression models, namely model for usage behaviour (UREFm model) and model for habitual behaviour (HREFm model) by using general perception, specific perception, and external factors as explanation variables. To collect data, a questionnaire was designed for survey which involved 40 respondents as a preliminary study and then statistical tests including regression analysis were applied to analyze usable data. The target of respondent was an owner of a house in Makassar with installed power capacity at least 900 VA. Reliability test shown that all items in the developed questionnaire can be used for main survey as obtained Cronbach’s alpha values were above 0.6. Evaluation for consumers perceptions on energy saving in relation to demographic aspect using mean and Standard Deviation values indicated some significant differences. Other results regarding regression analysis shown that both composed models were well validated and had quite good fitness degree with adjusted R-squared values around 49.31% for UREFm model and 80.90% for HREFm model. Among considered variables, specific perception, and external factors were found have significant influence to the usage and habitual behaviours of consumers as confirmed by their p-values in each model below 0.05. Findings of this research can be

  5. Gas appliances in the domestic market - legal basis and questioning concerning the Directive for Gas Appliances

    International Nuclear Information System (INIS)

    Rienen, W. van

    1994-01-01

    Four years after the Directive for Gas Appliances has been passed by the European Community it shows the first effects on the market. Gas appliances bearing an CE label can prove that the EC-standardised demands are observed. Thus it can be demanded from every member state by law not to hinder a launch on the market and the initiation. The directive also effects the demands for national environmental protection. A new DVGW (Deutscher Verein des Gas und Wasserfaches e.V.) quality label for gas appliances is going to certify the observance of a quality level which exceeds the minimum EC level. (orig.) [de

  6. 46 CFR 108.114 - Appliances for watertight and weathertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Appliances for watertight and weathertight integrity. (a) Appliances to ensure watertight integrity include... watertight decks and bulkheads. (b) Appliances to ensure weathertight integrity include weathertight doors...

  7. Embedded Systems for Smart Appliances and Energy Management

    CERN Document Server

    Neumann, Peter; Mahlknecht, Stefan

    2013-01-01

    This book provides a comprehensive introduction to embedded systems for smart appliances and energy management, bringing together for the first time a multidisciplinary blend of topics from embedded systems, information technology and power engineering.  Coverage includes challenges for future resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.   Provides a comprehensive, multidisciplinary introduction to embedded systems for smart appliances and energy management; Equips researchers and engineers with information required to succeed in designing energy management for smart appliances; Includes coverage of resource distribution grids, energy management in smart appliances, micro energy generation, demand response management, ultra-low power stand by, smart standby and communication networks in home and building automation.  

  8. 46 CFR 174.100 - Appliances for watertight and weathertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Appliances for watertight and weathertight integrity... Offshore Drilling Units § 174.100 Appliances for watertight and weathertight integrity. (a) Appliances to... watertight closures for openings in watertight decks and bulkheads. (b) Appliances to insure weathertight...

  9. Acceptability and attractiveness of intra- and extra-oral orthodontic appliances.

    Science.gov (United States)

    Abu Alhaija, Elham S J; Karajeh, M A

    2013-01-01

    To evaluate the acceptability of different intra-oral and extra-oral orthodontic appliances, to rank orthodontic appliances from the most to the least attractive and to investigate the factors that may affect the acceptance of orthodontic treatment. A random sample of 800 students (schoolchildren and university students) were invited to participate in this study and a total of 688 students were included (86%). A self-administrated structured questionnaire was constructed for the purpose of this study. More than one-half in each age group (53%) claimed that they would accept to have orthodontic treatment. Acceptance of the different orthodontic appliances was affected by gender, age and type of school. Removable appliance was reported as the most acceptable and facemask was reported as the least acceptable orthodontic appliances. Majority of subjects ranked ceramic and facemask appliances as the most and the least attractive orthodontic appliances, respectively. The predictor variables for the acceptance of orthodontic treatment were perceived demand for orthodontic treatment, perceived positive effect of orthodontic treatment and expected benefits from orthodontic treatment. Removable appliance was the most acceptable orthodontic appliance whereas ceramic appliance was ranked as the most attractive one. Facemask was the least acceptable and the least attractive option.

  10. Recycling-oriented characterization of small waste electrical and electronic equipment

    International Nuclear Information System (INIS)

    Chancerel, Perrine; Rotter, Susanne

    2009-01-01

    As a result of the continuous change in the design and function of consumer electrical and electronic products, the mechanical and material properties of the obsolete products, called waste electric and electronic equipment (WEEE), are highly variable. The variability within WEEE is explained by the number of different appliances, and the heterogeneity in composition of any given appliance. This paper reports on an extended investigation of the properties of WEEE, in particular small appliances. The investigation focuses on the analysis of the composition of about 700 single appliances. Firstly, analytical methods to characterize the waste equipment are described. The results of the experimental analyses show that the mechanical properties, the material composition, the polymer composition and the chemical composition of WEEE vary not only between equipment types with different functions, but also between single appliances within one equipment type. Data on hazardous and valuable substances in selected equipment types are presented. Using detailed data on the composition of individual appliances to calculate rates of recovery for assumed recycling processes demonstrates that the performance of recycling processes depends strongly on the composition of WEEE. Recycling-oriented characterization is, therefore, a systematic approach to support the design and the operation of recycling processes.

  11. Designing appliances for mobile commerce and retailtainment

    OpenAIRE

    Roussos, George; Kourouthanassis, P.; Moussouri, T.

    2003-01-01

    In the emerging world of the new consumer and the `anytime, anywhere' mobile commerce, appliances are located at the collision point of the retailer and consumer agendas. The consequence of this is twofold: on the one hand appliances that were previously considered plain and utilitarian become entertainment devices and on the other, for the effective design of consumer appliances it becomes paramount to employ multidisciplinary expertise. In this paper, we discuss consumer perceptions of a re...

  12. 14 CFR 21.502 - Approval of materials, parts, and appliances.

    Science.gov (United States)

    2010-01-01

    ... appliances. 21.502 Section 21.502 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF..., Materials, Parts, and Appliances: Import § 21.502 Approval of materials, parts, and appliances. (a) A material, part, or appliance, manufactured in a foreign country with which the United States has an...

  13. Cheap electricity with autonomous solar cell systems

    International Nuclear Information System (INIS)

    Ouwens, C.D.

    1993-01-01

    A comparison has been made between the costs of an autonomous solar cell system and a centralized electricity supply system. In both cases investment costs are the main issue. It is shown that for households in densely populated sunny areas, the use of autonomous solar cell systems is - even with today's market prices - only as expensive or even cheaper than a grid connection, as long as efficient electric appliances are used. The modular nature of solar cell systems makes it possible to start with any number of appliances, depending on the amount of money available to be spent. (author)

  14. 15 CFR 9.3 - Appliances and equipment included in program.

    Science.gov (United States)

    2010-01-01

    ... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Appliances and equipment included in... VOLUNTARY LABELING PROGRAM FOR HOUSEHOLD APPLIANCES AND EQUIPMENT TO EFFECT ENERGY CONSERVATION § 9.3 Appliances and equipment included in program. The appliances and equipment included in this program are room...

  15. Social perceptions of adults wearing orthodontic appliances: a cross-sectional study.

    Science.gov (United States)

    Jeremiah, H G; Bister, D; Newton, J T

    2011-10-01

    This study ascertained the influence of orthodontic appliances on subjective ratings for social competence (SC), intellectual ability (IA), psychological adjustment (PA), and attractiveness in young adult orthodontic patients. A cross-sectional analytical questionnaire study was conducted with 130 undergraduates from the UK. Each participant was asked to look at a single, randomly assigned colour photograph of a young adult female and then asked to make judgements concerning her personal characteristics. Five modified photographs of the same young adult female were used: (1) no appliance, (2) stainless steel fixed orthodontic appliance, (3) ceramic fixed orthodontic appliance, (4) gold fixed orthodontic appliance, and (5) clear colourless aligner. Likert scales with higher scores indicating more positive ratings were used. The results were analysed using chi-square test, one-way univariate analysis of variance, and post hoc Tukey-B and Kruskal-Wallis tests. The results showed that greater perceived IA was associated with the appearance of no appliance (mean values: 7.56) rather than steel (6.67) or ceramic appliances (6.65) but similar to the gold (7.35) and aligner (7.08) appliances. No significant differences between the different orthodontic appliance appearances were found for SC and PA. A trend existed where the no appliance image (resembling a lingual appliance) or clear aligner was considered more attractive than the visible buccal fixed appliances. In the absence of other information, the judgements an individual young adult makes concerning the personal characteristics of a young adult are influenced by dental appearance and orthodontic appliance design. This may influence orthodontic appliance choice.

  16. Pellet fired appliances. Market survey. 7. rev. ed.; Pelletheizungen. Marktuebersicht

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-01-15

    The market survey under consideration reports on pellet central heating systems and pellet fired appliances. The main chapters of this market survey are concerned to: (1) Information on wood pellets and pellet fired appliances; (2) Information about the interpretation of the market survey; (3) Survey of all compared pellet fired appliances with respect to the nominal power; (4) Price lists of pellet fired appliances and pellet central heating systems; (5) Type sheets of the compared pellet fired appliances and pellet central heating systems. Finally, this brochure contains the addresses of the produces and distribution partners of pellet fired appliances and pellet central heating systems.

  17. A retrospective cephalometric investigation of two fixed functional orthodontic appliances in class II treatment: Functional Mandibular Advancer vs. Herbst appliance.

    Science.gov (United States)

    Kinzinger, Gero Stefan Michael; Lisson, Jörg Alexander; Frye, Linda; Gross, Ulrich; Hourfar, Jan

    2018-01-01

    The objective of the study is to compare skeletal and dental changes in class II patients treated with fixed functional appliances (FFA) that pursue different biomechanical concepts: (1) FMA (Functional Mandibular Advancer) from first maxillary molar to first mandibular molar through inclined planes and (2) Herbst appliance from first maxillary molar to lower first bicuspid through a rod-and-tube mechanism. Forty-two equally distributed patients were treated with FMA (21) and Herbst appliance (21), following a single-step advancement protocol. Lateral cephalograms were available before treatment and immediately after removal of the FFA. The lateral cephalograms were analyzed with customized linear measurements. The actual therapeutic effect was then calculated through comparison with data from a growth survey. Additionally, the ratio of skeletal and dental contributions to molar and overjet correction for both FFA was calculated. Data was analyzed by means of one-sample Student's t tests and independent Student's t tests. Statistical significance was set at p appliance were found, intergroup comparisons showed no statistically significant differences. Almost all measurements resulted in comparable changes for both appliances. Statistically significant dental changes occurred with both appliances. Dentoalveolar contribution to the treatment effect was ≥70%, thus always resulting in ≤30% for skeletal alterations. FMA and Herbst appliance usage results in comparable skeletal and dental treatment effects despite different biomechanical approaches. Treatment leads to overjet and molar relationship correction that is mainly caused by significant dentoalveolar changes.

  18. Unilateral maxillary molar distalization with zygoma-gear appliance.

    Science.gov (United States)

    Kilkis, Dogan; Bayram, Mehmet; Celikoglu, Mevlut; Nur, Metin

    2012-08-01

    The aim of this study was to present the orthodontic treatment of a 15-year-old boy with a unilateral maxillary molar distalization system, called the zygoma-gear appliance. It consisted of a zygomatic anchorage miniplate, an inner bow, and a Sentalloy closed coil spring (GAC International, Bohemia, NY). A distalizing force of 350 g was used during the distalization period. The unilateral Class II malocclusion was corrected in 5 months with the zygoma-gear appliance. The maxillary left first molar showed distalization of 4 mm with an inclination of 3°. The maxillary premolars moved distally with the help of the transseptal fibers. In addition, there were slight decreases in overjet (-0.5 mm) and maxillary incisor inclination (-1°), indicating no anchorage loss from the zygoma-gear appliance. Preadjusted fixed appliances (0.022 × 0.028-in, MBT system; 3M Unitek, Monrovia, Calif) were placed in both arches to achieve leveling and alignment. After 14 months of unilateral distalization with the zygoma-gear appliance and fixed appliances, Class I molar and canine relationships were established with satisfactory interdigitation of the posterior teeth. Acceptable overjet and overbite were also achieved. This article shows that this new system, the zygoma-gear appliance, can be used for unilateral maxillary molar distalization without anchorage loss. Copyright © 2012 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  19. 29 CFR 1915.132 - Portable electric tools.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Portable electric tools. 1915.132 Section 1915.132 Labor... § 1915.132 Portable electric tools. The provisions of this section shall apply to ship repairing... frames of portable electric tools and appliances, except double insulated tools approved by Underwriters...

  20. Households' hourly electricity consumption and peak demand in Denmark

    DEFF Research Database (Denmark)

    Møller Andersen, Frits; Baldini, Mattia; Hansen, Lars Gårn

    2017-01-01

    consumption, we analyse the contribution of appliances and new services, such as individual heat pumps and electric vehicles, to peak consumption and the need for demand response incentives to reduce the peak.Initially, the paper presents a new model that represents the hourly electricity consumption profile...... of households in Denmark. The model considers hourly consumption profiles for different household appliances and their contribution to annual household electricity consumption. When applying the model to an official scenario for annual electricity consumption, assuming non-flexible consumption due...... to a considerable introduction of electric vehicles and individual heat pumps, household consumption is expected to increase considerably, especially peak hour consumption is expected to increase.Next the paper presents results from a new experiment where household customers are given economic and/or environmental...

  1. Estimating Price Elasticity using Market-Level Appliance Data

    Energy Technology Data Exchange (ETDEWEB)

    Fujita, K. Sydny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2015-08-04

    This report provides and update to and expansion upon our 2008 LBNL report “An Analysis of the Price Elasticity of Demand for Appliances,” in which we estimated an average relative price elasticity of -0.34 for major household appliances (Dale and Fujita 2008). Consumer responsiveness to price change is a key component of energy efficiency policy analysis; these policies influence consumer purchases through price both explicitly and implicitly. However, few studies address appliance demand elasticity in the U.S. market and public data sources are generally insufficient for rigorous estimation. Therefore, analysts have relied on a small set of outdated papers focused on limited appliance types, assuming long-term elasticities estimated for other durables (e.g., vehicles) decades ago are applicable to current and future appliance purchasing behavior. We aim to partially rectify this problem in the context of appliance efficiency standards by revisiting our previous analysis, utilizing data released over the last ten years and identifying additional estimates of durable goods price elasticities in the literature. Reviewing the literature, we find the following ranges of market-level price elasticities: -0.14 to -0.42 for appliances; -0.30 to -1.28 for automobiles; -0.47 to -2.55 for other durable goods. Brand price elasticities are substantially higher for these product groups, with most estimates -2.0 or more elastic. Using market-level shipments, sales value, and efficiency level data for 1989-2009, we run various iterations of a log-log regression model, arriving at a recommended range of short run appliance price elasticity between -0.4 and -0.5, with a default value of -0.45.

  2. The electric comfort; Le confort electrique

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    In the framework of the public information on the electric power utilization in the household, Electricite De France presented on april-may at Paris Meeting, the possibilities and the advantages of the electric comfort. The concerned domains are: the electric cheating, the air-conditioning, the hot water, the lighting and the electric household appliances. Information on prices and statistical data on electric heating are also provided. (A.L.B.)

  3. Second-home electricity consumption

    International Nuclear Information System (INIS)

    Andersen, Frits M.; Christensen, Morten S.; Jensen, Ole Michael; Kofoed, Niels-Ulrik; Morthorst, Poul Erik

    2008-01-01

    In Denmark, electricity consumption in first and second homes has developed quite differently. Since 1990, electricity consumption in ordinary residences has grown moderately, while consumption in weekend and second homes has increased considerably. In turn, this development has been blamed on a growing number of luxury cottages, new legislation permitting senior citizens to have their permanent address in their second home and a growing number of electric appliances. In order to examine the growing electricity consumption in second homes and to estimate future demand, a multidisciplinary study combining top-down and bottom-up analyses was conducted, i.e., combining models using aggregated economic parameters and feasibility studies using technical parameters, respectively. The top-down estimation showed that changes in electricity consumption in second homes correlate to changes in income. The bottom-up estimation showed that consumption was mainly affected by the frequency with which second homes were used in the winter time. This indicates that additional second homes, increased full-time use and intensified use of electric appliances are the main reasons for the observed increases in electricity consumption. Luxury tourism use and senior citizens' that use a few per cent of the second homes as their home contribute to a minor degree to the overall increase of electricity consumption. Scenarios show that this development may accelerate with increased leisure time, increased use and more permanent settlement in second homes

  4. Appliance choice functions in Canadian households. Paper no. IGEC-1-ID02

    International Nuclear Information System (INIS)

    Aydinalp, M.; Fung, A.; Ugursal, V.I.

    2005-01-01

    Decisions regarding the purchase of various types of major household appliances are influenced by the economic and demographic characteristics of households, i.e., appliance customers. It is therefore necessary to understand the relationship between these characteristics and the decisions made regarding the purchase of appliances to be able to predict future trends in appliance purchases, and consequently, the future appliance energy consumption of the national stock of appliances. In this paper, a methodology is presented to develop choice functions for the purchase of new major household appliances. This methodology is used to develop appliance choice functions for Canada. (author)

  5. Orthodontic appliance preferences of children and adolescents.

    Science.gov (United States)

    Walton, Daniel K; Fields, Henry W; Johnston, William M; Rosenstiel, Stephen F; Firestone, Allen R; Christensen, James C

    2010-12-01

    Although attractiveness and acceptability of orthodontic appliances have been rated by adults for themselves and for adolescents, children and adolescents have not provided any substantial data. The objective of this study was to evaluate preferences and acceptability of orthodontic appliances in children and adolescents. Images of orthodontic appliances previously captured and standardized were selected and incorporated into a computer-based survey. Additional images of shaped brackets and colored elastomeric ties, as well as discolored clear elastomeric ties, were captured and incorporated onto existing survey images with Photoshop (Adobe, San Jose, Calif). The survey displayed 12 orthodontic appliance variations to 139 children in 3 age groups: 9 to 11 years (n = 45), 12 to 14 years (n = 49), and 15 to 17 years (n = 45). The subjects rated each image for attractiveness and acceptability. All images were displayed and rated twice to assess rater reliability. Overall reliability ratings were r = 0.74 for attractiveness and k = 0.66 for acceptability. There were significant differences in bracket attractiveness and acceptability in each age group. The highest-rated appliances were clear aligners, twin brackets with colored ties, and shaped brackets with and without colored ties. Colored elastomeric ties improved attractiveness significantly over brackets without colored ties for children in the 12-to-14 year group. There was a tendency for older subjects to rate clear orthodontic appliances higher than did younger subjects. Ceramic brackets with discolored ties tended to be rated lower than ceramic brackets with new ties and scored lowest in acceptability and attractiveness in all age groups. Girls rated shaped brackets significantly higher than did boys. Children's preferences for orthodontic appliances differ by age and sex. Child and adolescent preferences differ from adult preferences. Copyright © 2010 American Association of Orthodontists. Published by Mosby

  6. Quality of Lab Appliances in Orthodontic Offices.

    Science.gov (United States)

    Pruzansky, D P; Park, J H

    Lab appliances are an integral part of orthodontics, from active treatment to retention. The quality and fit of an appliance can affect the treatment result and stability. This study aims to determine common points of failure in orthodontic appliances, and suggest methods to reduce this rate. A survey consisting of 23 questions was distributed to active members of the American Association of Orthodontists (AAO) via Survey Monkey. The most common appliance to need an adjustment was the wrap-around retainer, with the Hawley retainer as a close second. The least common appliance needing adjustment was the Essix/clear retainer. Respondents were asked which component of each appliance was most commonly responsible for an ill-fit. For Hawley and wrap-around retainers, clasps were the most common problem at 50%, whereas spring aligners had two components - clasps and labial bows, both at 38%. Ill-fitting Essix/clear retainers had gingival impingement (52%) closely followed by poor posterior seating (43%). Communication between the orthodontist and lab technician can be improved by establishing a quality assurance protocol for outgoing and incoming cases. The labial bow of Hawley's, wrap-arounds and spring aligners should be clearly demarcated on the casts. Impressions should be free of distortion and casts should be inspected for accuracy. Clear retainers and positioner should be trimmed to avoid gingival impingement. The type of clasp should be selected based on the anatomy of the teeth, and bands should be checked for accuracy of fit.

  7. Emergencies in Orthodontics. Part 2: Management of Removable Appliances, Functional Appliances and other Adjuncts to Orthodontic Treatment.

    Science.gov (United States)

    Dowsing, Paul; Murray, Alison; Sandler, Jonathan

    2015-04-01

    In the second of two papers, management of orthodontic emergencies involving appliances other than Fixed appliances will be detailed. Problems relating to removable appliances, as well as other orthodontic adjuncts, will be discussed. Unfortunately, orthodontic appliance breakage does occur, despite the clinicians giving clear and concise instructions to the patients and their parents at fitting. If general dental practitioners have a practical knowledge of how to diagnose problems and to provide appropriate advice or timely 'emergency' treatment, this will significantly reduce the inconvenience for all parties concerned. It should also ensure that treatment progresses in the most efficient and comfortable manner for their patients. In specific situations the early, accurate identification of the problem and instigation of its appropriate management can avoid more serious consequences. Clinical Relevance: Appropriate handling of an orthodontic 'emergency' by the dentist can, on many occasions, provide immediate relief to the patient. This will, in turn, allow treatment to continue in the right direction, thus allowing more efficient and effective use of valuable resources.

  8. An Analysis on change of household electricity demand pattern

    Energy Technology Data Exchange (ETDEWEB)

    Na, In Gang [Korea Energy Economics Institute, Euiwang (Korea)

    1999-01-01

    The object of this study is to analyze the behavioral pattern change of household electricity demand. Through the cross section analysis using materials from the energy total research report, the change in income elasticity of household electricity demand was studied. In this study, two methodologies were used. Firstly, it was shown that the effect of an income variable was very significant with a positive value in simultaneous equations model using exponential equations of electrical appliances holding. Cross section income effect showed a various distribution according to the season or income level. Overall, it was calculated at 0.111 when the appliances are fixed and 0.432 when even appliances are changed. Secondly, using a choice convenient correction model, it is resulted that lambda, the choice convenient correction factor, has a positive value and is statistically significant. In 1996, income elasticity of electricity demand for households with air-conditioning was 0.305 and for households without air-conditioning was 0.172. Income elasticity of households with air-conditioning is increasing as time goes by while income elasticity of households without air-conditioning is decreasing. (author). 32 refs., 35 tabs.

  9. Crew appliance concepts. Volume 2, appendix B: Shuttle orbiter appliances supporting engineering data. [food management and personal hygiene

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Technical data collected for the food management and personal hygiene appliances considered for the shuttle orbiter are presented as well as plotted and tabulated trade study results for each appliance. Food storage, food operation, galley cleanup, waste collection/transfer, body cleansing, and personal grooming were analyzed.

  10. 14 CFR 21.305 - Approval of materials, parts, processes, and appliances.

    Science.gov (United States)

    2010-01-01

    ..., and appliances. 21.305 Section 21.305 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION..., Parts, Processes, and Appliances § 21.305 Approval of materials, parts, processes, and appliances. Whenever a material, part, process, or appliance is required to be approved under this chapter, it may be...

  11. Initial Evaluation of a Titration Appliance for Temporary Treatment of Obstructive Sleep Apnea.

    Science.gov (United States)

    Levendowski, Daniel J; Morgan, Todd; Westbrook, Philip

    2012-01-01

    Custom oral appliances that adjustably advance the mandible provide superior outcomes when treating patients with moderate or severe sleep apnea. Custom appliances, however, are expensive, must be fitted by a dentist, and the likelihood of successful outcomes are difficult to predict. An inexpensive trial appliance, if proven efficacious, might be used to predict custom appliance outcomes or to provide temporary therapeutic benefit. The aim of this initial study was to assess the treatment efficacy of a novel titration oral appliance with that of an optimized custom appliance. Seventeen patients, treated with a custom oral appliance for at least one year, successfully completed a three-night home sleep test. The baseline obstructive sleep apnea severity was established on Night 1 with seven patients exhibiting severe, six moderate and four mild apnea/hypopnea indexes. Patients were randomly assigned to wear their custom appliance or the titration appliance on Nights 2 and 3. Significant reductions in the mean overall and supine apnea indexes (p titration and custom appliances. The proportion of patients who exhibited at least a 50% reduction in the overall apnea index and supine apnea/hypopnea were similar for the titration and custom appliance (~60%). The custom appliance reduced the overall apnea/hypopnea index by 50% in a greater proportion of the patients compared to the titration appliance (77% vs. 53%). The titration appliance significantly reduced the degree of hypoxic exposure across sleep disordered breathing events overall (p titration appliance, but preferred the titration appliance to no therapy. The titration appliance may be useful in assessing oral appliance treatment efficacy. When set to 70% of maximum protrusion, the titration appliance may provide immediate, temporary therapeutic benefit.

  12. Crew appliance concepts. Volume 4, appendix C: Modular space station appliances supporting engineering data. [food management and personal hygiene

    Science.gov (United States)

    Proctor, B. W.; Reysa, R. P.; Russell, D. J.

    1975-01-01

    Data collected for the appliances considered for the space station are presented along with plotted and tabulated trade study results for each appliance. The food management, and personal hygiene data are applicable to a six-man mission of 180-days.

  13. Measurements of intermediate-frequency electric and magnetic fields in households

    Energy Technology Data Exchange (ETDEWEB)

    Aerts, Sam, E-mail: sam.aerts@intec.ugent.be [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium); Calderon, Carolina [Centre for Radiation, Chemical and Environmental Hazards, Public Health England, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom); Valič, Blaž [Institute of Non-Ionizing Radiation (INIS), Pohorskega bataljona 215, Ljubljana 1000 (Slovenia); Maslanyj, Myron; Addison, Darren; Mee, Terry; Goiceanu, Cristian [Centre for Radiation, Chemical and Environmental Hazards, Public Health England, Chilton, Didcot, Oxon OX11 0RQ (United Kingdom); Verloock, Leen; Van den Bossche, Matthias [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium); Gajšek, Peter [Institute of Non-Ionizing Radiation (INIS), Pohorskega bataljona 215, Ljubljana 1000 (Slovenia); Vermeulen, Roel [Institute for Risk Assessment Sciences, Department of Environmental Epidemiology, Utrecht University, Yalelaan 2, 3508 Utrecht (Netherlands); Röösli, Martin [Swiss Tropical and Public Health Institute (Swiss TPH), Socinstrasse 57, P.O. Box, 4002 Basel (Switzerland); University of Basel, Petersplatz 1, 4003 Basel (Switzerland); Cardis, Elisabeth [Barcelona Institute for Global Health (ISGlobal) and Municipal Institute of Medical Research (IMIM-Hospital del Mar), Doctor Aiguader, 88, 08003 Barcelona (Spain); Martens, Luc; Joseph, Wout [Department of Information Technology, Ghent University/iMinds, iGent, Technologiepark-Zwijnaarde 15, B-9052 Ghent (Belgium)

    2017-04-15

    Historically, assessment of human exposure to electric and magnetic fields has focused on the extremely-low-frequency (ELF) and radiofrequency (RF) ranges. However, research on the typically emitted fields in the intermediate-frequency (IF) range (300 Hz to 1 MHz) as well as potential effects of IF fields on the human body remains limited, although the range of household appliances with electrical components working in the IF range has grown significantly (e.g., induction cookers and compact fluorescent lighting). In this study, an extensive measurement survey was performed on the levels of electric and magnetic fields in the IF range typically present in residences as well as emitted by a wide range of household appliances under real-life circumstances. Using spot measurements, residential IF field levels were found to be generally low, while the use of certain appliances at close distance (20 cm) may result in a relatively high exposure. Overall, appliance emissions contained either harmonic signals, with fundamental frequencies between 6 kHz and 300 kHz, which were sometimes accompanied by regions in the IF spectrum of rather noisy, elevated field strengths, or much more capricious spectra, dominated by 50 Hz harmonics emanating far in the IF domain. The maximum peak field strengths recorded at 20 cm were 41.5 V/m and 2.7 A/m, both from induction cookers. Finally, none of the appliance emissions in the IF range exceeded the exposure summation rules recommended by the International Commission on Non-Ionizing Radiation Protection guidelines and the International Electrotechnical Commission (IEC 62233) standard at 20 cm and beyond (maximum exposure quotients EQ{sub E} 1.0 and {sub E}Q{sub H} 0.13). - Highlights: • Survey of residential electric and magnetic fields at intermediate frequencies (IF). • IF-EF and -MF emitted by 280 household appliances were characterised. • Strongest emitters were induction cookers, CFLs, LCD-TVs, and microwave ovens. • No

  14. Measurements of intermediate-frequency electric and magnetic fields in households

    International Nuclear Information System (INIS)

    Aerts, Sam; Calderon, Carolina; Valič, Blaž; Maslanyj, Myron; Addison, Darren; Mee, Terry; Goiceanu, Cristian; Verloock, Leen; Van den Bossche, Matthias; Gajšek, Peter; Vermeulen, Roel; Röösli, Martin; Cardis, Elisabeth; Martens, Luc; Joseph, Wout

    2017-01-01

    Historically, assessment of human exposure to electric and magnetic fields has focused on the extremely-low-frequency (ELF) and radiofrequency (RF) ranges. However, research on the typically emitted fields in the intermediate-frequency (IF) range (300 Hz to 1 MHz) as well as potential effects of IF fields on the human body remains limited, although the range of household appliances with electrical components working in the IF range has grown significantly (e.g., induction cookers and compact fluorescent lighting). In this study, an extensive measurement survey was performed on the levels of electric and magnetic fields in the IF range typically present in residences as well as emitted by a wide range of household appliances under real-life circumstances. Using spot measurements, residential IF field levels were found to be generally low, while the use of certain appliances at close distance (20 cm) may result in a relatively high exposure. Overall, appliance emissions contained either harmonic signals, with fundamental frequencies between 6 kHz and 300 kHz, which were sometimes accompanied by regions in the IF spectrum of rather noisy, elevated field strengths, or much more capricious spectra, dominated by 50 Hz harmonics emanating far in the IF domain. The maximum peak field strengths recorded at 20 cm were 41.5 V/m and 2.7 A/m, both from induction cookers. Finally, none of the appliance emissions in the IF range exceeded the exposure summation rules recommended by the International Commission on Non-Ionizing Radiation Protection guidelines and the International Electrotechnical Commission (IEC 62233) standard at 20 cm and beyond (maximum exposure quotients EQ E 1.0 and E Q H 0.13). - Highlights: • Survey of residential electric and magnetic fields at intermediate frequencies (IF). • IF-EF and -MF emitted by 280 household appliances were characterised. • Strongest emitters were induction cookers, CFLs, LCD-TVs, and microwave ovens. • No emissions exceeded

  15. Measure Guideline: Combustion Safety for Natural Draft Appliances Through Appliance Zone Isolation

    Energy Technology Data Exchange (ETDEWEB)

    Fitzgerald, J. [Center for Energy and Environment, Minneapolis, MN (United States); Bohac, D. [Center for Energy and Environment, Minneapolis, MN (United States)

    2014-04-01

    This measure guideline covers how to assess and carry out the isolation of natural draft combustion appliances from the conditioned space of low-rise residential buildings. It deals with combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage. This subset of houses does not require comprehensive combustion safety tests and simplified prescriptive procedures can be used to address safety concerns. This allows residential energy retrofit contractors inexperienced in advanced combustion safety testing to effectively address combustion safety issues and allow energy retrofits including tightening and changes to distribution and ventilation systems to proceed.

  16. 46 CFR 31.36-1 - Lifesaving appliances and arrangements-TB/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Lifesaving appliances and arrangements-TB/ALL. 31.36-1... CERTIFICATION Lifesaving Appliances and Arrangements § 31.36-1 Lifesaving appliances and arrangements—TB/ALL. All lifesaving appliances and arrangements on tank vessels must be in accordance with subchapter W...

  17. Speech and orthodontic appliances: a systematic literature review.

    Science.gov (United States)

    Chen, Junyu; Wan, Jia; You, Lun

    2018-01-23

    Various types of orthodontic appliances can lead to speech difficulties. However, speech difficulties caused by orthodontic appliances have not been sufficiently investigated by an evidence-based method. The aim of this study is to outline the scientific evidence and mechanism of the speech difficulties caused by orthodontic appliances. Randomized-controlled clinical trials (RCT), controlled clinical trials, and cohort studies focusing on the effect of orthodontic appliances on speech were included. A systematic search was conducted by an electronic search in PubMed, EMBASE, and the Cochrane Library databases, complemented by a manual search. The types of orthodontic appliances, the affected sounds, and duration period of the speech disturbances were extracted. The ROBINS-I tool was applied to evaluate the quality of non-randomized studies, and the bias of RCT was assessed based on the Cochrane Handbook for Systematic Reviews of Interventions. No meta-analyses could be performed due to the heterogeneity in the study designs and treatment modalities. Among 448 screened articles, 13 studies were included (n = 297 patients). Different types of orthodontic appliances such as fixed appliances, orthodontic retainers and palatal expanders could influence the clarity of speech. The /i/, /a/, and /e/ vowels as well as /s/, /z/, /l/, /t/, /d/, /r/, and /ʃ/ consonants could be distorted by appliances. Although most speech impairments could return to normal within weeks, speech distortion of the /s/ sound might last for more than 3 months. The low evidence level grading and heterogeneity were the two main limitations in this systematic review. Lingual fixed appliances, palatal expanders, and Hawley retainers have an evident influence on speech production. The /i/, /s/, /t/, and /d/ sounds are the primarily affected ones. The results of this systematic review should be interpreted with caution and more high-quality RCTs with larger sample sizes and longer follow-up periods are

  18. 46 CFR 78.17-5 - Valves and closing appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.17-5 Section 78.17-5..., Drills, and Inspections § 78.17-5 Valves and closing appliances. (a) It shall be the duty of the master to see that all valves, including cross connecting valves where fitted, and other appliances such as...

  19. 46 CFR 78.47-38 - Valves and closing appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Valves and closing appliances. 78.47-38 Section 78.47-38... Fire and Emergency Equipment, Etc. § 78.47-38 Valves and closing appliances. (a) All valves and closing appliances, or other mechanisms which may be required to be operated for damage control purposes in case of...

  20. 46 CFR 108.580 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 108.580 Section 108.580 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.580 Personal lifesaving appliances. (a) Lifebuoys. Each unit...

  1. 46 CFR 133.70 - Personal lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Personal lifesaving appliances. 133.70 Section 133.70 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS LIFESAVING SYSTEMS Requirements for All OSVs § 133.70 Personal lifesaving appliances. (a) Lifebuoys. Each OSV must...

  2. A cephalometric comparison of treatment with the Twin-block and stainless steel crown Herbst appliances followed by fixed appliance therapy.

    Science.gov (United States)

    Schaefer, Abbie T; McNamara, James A; Franchi, Lorenzo; Baccetti, Tiziano

    2004-07-01

    This study compared the effects of 2 treatment protocols for correcting Class II disharmony. The first phase of treatment consisted of functional jaw orthopedics with either the Twin-block or the stainless-steel crown Herbst appliance; the second phase consisted of comprehensive fixed-appliance therapy in both protocols. Each of the 2 samples comprised 28 consecutively treated Class II patients. The mean age at the start of treatment was approximately 12 years, and the mean age at the end of the treatment was approximately 14.5 years in both groups. The duration of the treatment phase with the functional appliance was approximately 13 months, and the duration of fixed-appliance therapy was approximately 15 months in both groups. The sex distribution was identical in the 2 groups. Lateral cephalograms were analyzed at the start of treatment (T1) and at the end of the overall treatment protocol (T2). Nonparametric statistics were used for comparisons of starting forms and of the T1-T2 changes between the 2 treatment groups. The stainless-steel crown Herbst appliance and the Twin-block appliance produced very similar therapeutic modifications in Class II patients, although the Twin-block group exhibited almost 2 mm greater correction of the maxillomandibular differential than did the crown Herbst group. The treatment effects of both protocols led to a normalization of the dentoskeletal parameters at the end of the overall treatment period. Twin-block therapy also induced a greater increase in the height of the mandibular ramus (posterior facial height). Overall, only minor differences were detected in the treatment and posttreatment effects of a compliance-free (crown Herbst) and a noncompliance-free (Twin-block) appliance for correcting Class II disharmony.

  3. Second-home electricity consumption

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, Frits M.; Morthorst, Poul Erik [Risoe, Systems Analysis Department, Technical University of Denmark, P.O. Box 49, DK-4000 Roskilde (Denmark); Christensen, Morten S.; Kofoed, Niels-Ulrik [Esbensen Consulting Engineers, Carl Jacobsens Vej 25D, DK-2500 Valby (Denmark); Jensen, Ole Michael [Danish Building Research Institute, Department of Energy and Environment, University of Aalborg, P.O. Box 119, DK-2970 Horsholm (Denmark)

    2008-01-15

    In Denmark, electricity consumption in first and second homes has developed quite differently. Since 1990, electricity consumption in ordinary residences has grown moderately, while consumption in weekend and second homes has increased considerably. In turn, this development has been blamed on a growing number of luxury cottages, new legislation permitting senior citizens to have their permanent address in their second home and a growing number of electric appliances. In order to examine the growing electricity consumption in second homes and to estimate future demand, a multidisciplinary study combining top-down and bottom-up analyses was conducted, i.e., combining models using aggregated economic parameters and feasibility studies using technical parameters, respectively. The top-down estimation showed that changes in electricity consumption in second homes correlate to changes in income. The bottom-up estimation showed that consumption was mainly affected by the frequency with which second homes were used in the winter time. This indicates that additional second homes, increased full-time use and intensified use of electric appliances are the main reasons for the observed increases in electricity consumption. Luxury tourism use and senior citizens' that use a few per cent of the second homes as their home contribute to a minor degree to the overall increase of electricity consumption. Scenarios show that this development may accelerate with increased leisure time, increased use and more permanent settlement in second homes. (author)

  4. 42 CFR 409.25 - Drugs, biologicals, supplies, appliances, and equipment.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Drugs, biologicals, supplies, appliances, and... Drugs, biologicals, supplies, appliances, and equipment. (a) Drugs and biologicals. Except as specified... can obtain a continuing supply. (c) Supplies, appliances, and equipment. Except as specified in...

  5. Hydrophilic structures for condensation management in refrigerator appliances

    Science.gov (United States)

    Kuehl, Steven John; Vonderhaar, John J; Wu, Guolian; Wu, Mianxue

    2014-10-21

    A refrigerator appliance that includes a freezer compartment having a freezer compartment door, and a refrigeration compartment having at least one refrigeration compartment door. The appliance further includes a mullion with an exterior surface. The mullion divides the compartments and the exterior surface directs condensation toward a transfer point. The appliance may also include a cabinet that houses the compartments and has two sides, each with an exterior surface. Further, at least one exterior surface directs condensation toward a transfer point.

  6. Research & Development Roadmap for Next-Generation Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States); Foley, Kevin [Navigant Consulting, Inc., Burlington, MA (United States)

    2012-03-01

    Appliances present an attractive opportunity for near-term energy savings in existing building, because they are less expensive and replaced more regularly than heating, ventilation, and air-conditioning (HVAC) systems or building envelope components. This roadmap targets high-priority research and development (R&D), demonstration and commercialization activities that could significantly reduce residential appliance energy consumption. The main objective of the roadmap is to seek activities that accelerate the commercialization of high-efficiency appliance technologies while maintaining the competitiveness of American industry. The roadmap identified and evaluated potential technical innovations, defined research needs, created preliminary research and development roadmaps, and obtained stakeholder feedback on the proposed initiatives.

  7. Drawing on international experience to reform the Belgian market for ostomy appliances.

    Science.gov (United States)

    Simoens, Steven; Van den Steen, Dirk; Vanleene, Veerle; De Maré, Luc; Moldenaers, Ingrid; Debruyne, Hans; Ramaekers, Dirk

    2007-02-01

    This article aims to review the regulatory framework governing the Belgian ostomy appliance market in the light of the experience of Denmark, France, the Netherlands and Ontario (Canada) with regulation of ostomy appliances. Information about the regulatory framework was derived from the international literature, analysis of legal texts and a survey completed by national experts. The comparative analysis revealed that these countries have adopted varying approaches towards regulating their domestic ostomy appliance market. Strategies to keep down prices include public procurement in Denmark, maximum prices in France and exclusion of expensive appliances from reimbursement in the Netherlands. To contain public expenditure on ostomy appliances, consumption patterns are monitored in the Netherlands, the quantity of reimbursed appliances is limited in Belgium and public reimbursement is restricted in Ontario. Ostomy appliances are generally distributed by community pharmacies and medical equipment shops. In countries that emphasise home care delivery such as Denmark, domiciliary distributors dominate the market to the detriment of community pharmacies which do not seem to be able to offer this service at a competitive price. An avenue for reforming the Belgian ostomy appliance market is proposed which valorizes the role of ostomy care nurses in guiding the choice of ostomy appliances. Furthermore, it is recommended that a competitive tendering process determines the price of ostomy appliances, that reimbursement for service provision by distributors is separated from reimbursement of appliances, and that patients receive a fixed grant from the third-party payer to buy ostomy appliances.

  8. 38 CFR 17.153 - Training in the use of appliances.

    Science.gov (United States)

    2010-07-01

    ... appliances. 17.153 Section 17.153 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS MEDICAL Prosthetic, Sensory, and Rehabilitative Aids § 17.153 Training in the use of appliances. Beneficiaries supplied prosthetic and similar appliances will be additionally entitled to fitting and training...

  9. 14 CFR 183.63 - Continuing requirements: Products, parts or appliances.

    Science.gov (United States)

    2010-01-01

    ... appliances. 183.63 Section 183.63 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF... Designation Authorization § 183.63 Continuing requirements: Products, parts or appliances. For any approval or certificate for a product, part or appliance issued under the authority of this subpart, or under the...

  10. GE Appliance Park Louisville, KY Plant Wide Assessment Final Report October 25th, 2007

    Energy Technology Data Exchange (ETDEWEB)

    Chandon Rao; Richard Urschel

    2007-10-25

    Used a team of experts to analyze and model major systems at a large industrial appliance manufacturer. During the data gathering stage, the team specifically looked for baselining the efficiency of the systems as well as developing short term and longer term efficiency projects. Electrical distribution, Compressed air generation and thermal heat recovery for the production facility and front office heating and cooling optimization were all baselined during the study.

  11. Measurement of HTO permeability of materials for protective appliances

    International Nuclear Information System (INIS)

    Yamamoto, H.; Tomooka, M.; Kato, S.; Murata, M.; Kinouchi, N.; Yamamoto, H.

    1992-01-01

    Tritiated water (HTO) vapor permeabilities were measured for plastic and rubber films used for protective appliances (suits, gloves, wrappings, etc.). The measurement data prove that polyehylene and butyl rubbers are materials suitable for HTO protective appliances with their lower permeability. The data also indicate that desiccating protective appliances before reuse is effective for restoring their original resistances to penetrating HTO vapor when they are repeatedly used. (author)

  12. 49 CFR 238.229 - Safety appliances-general.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-general. 238.229 Section 238.229... Equipment § 238.229 Safety appliances—general. (a) Except as provided in this part, all passenger equipment continues to be subject to the safety appliance requirements contained in Federal statute at 49 U.S.C...

  13. When do energy-efficient appliances generate energy savings? Some evidence from Canada

    International Nuclear Information System (INIS)

    Young, Denise

    2008-01-01

    Improvements in the energy efficiency of household appliances have the potential to decrease residential energy use, but these reductions accrue gradually over time as newer appliances replace older models. SHEU-2003 data are used to examine appliance replacement patterns in Canada for refrigerators, freezers, dishwashers, clothes washers and clothes dryers. The data indicate that the ages at which appliances are replaced tend to be lowest for dishwashers and highest for freezers, with over 40% of freezers in use for more than 20 years before being retired. The life spans of Canadian appliances are compared to the underlying assumptions regarding appliance lifetimes used in models of residential energy demand. We find that Canadian appliance retirement patterns differ from those assumed in the previous literature. Socioeconomic factors related to appliance replacement are also examined. We find that replacement patterns can be sensitive to household characteristics such as income, providing evidence that there may be scope for targeted policies aimed at inducing earlier replacements of older household appliances with new energy-efficient models

  14. Extra-oral Appliances in Orthodontic Treatment.

    Science.gov (United States)

    Almuzian, Mohammed; Alharbi, Fahad; McIntyre, Grant

    2016-01-01

    Extra-oral appliances are used in orthodontics to apply forces to the jaws, dentition or both and the popularity of these appliances is cyclical. Although the use of retraction headgear for the management of Class II malocclusion has declined over the last 20 years with the refinement of non-compliance approaches, including temporary anchorage devices, headgear still has a useful role in orthodontics. The use of protraction headgear has increased as more evidence of its effectiveness for the treatment of Class lIl malocclusion has become available. This paper describes the mechanics and contemporary uses of headgear in orthodontics for primary care dentists and specialist orthodontists. CPD/CLINICAL RELEVANCE: Extra-oral appliances have specific uses in orthodontic biomechanics. Clinicians using retraction headgear and protraction headgear should be familiar with their clinical indications, the potential problems and how these can be avoided.

  15. 42 CFR 410.36 - Medical supplies, appliances, and devices: Scope.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Medical supplies, appliances, and devices: Scope... Services § 410.36 Medical supplies, appliances, and devices: Scope. (a) Medicare Part B pays for the following medical supplies, appliances and devices: (1) Surgical dressings, and splints, casts, and other...

  16. Custom Made Pressure Appliance for Presurgical Sustained ...

    African Journals Online (AJOL)

    Among the most common complications of this therapy is ulceration due to excessive pressure. A case of presurgical size reduction for a large ear keloid with a custom made pressure appliance is presented. This novel design of the appliance allows for better control over the amount and direction of the pressure applied on ...

  17. Status Checking System of Home Appliances using machine learning

    Directory of Open Access Journals (Sweden)

    Yoon Chi-Yurl

    2017-01-01

    Full Text Available This paper describes status checking system of home appliances based on machine learning, which can be applied to existing household appliances without networking function. Designed status checking system consists of sensor modules, a wireless communication module, cloud server, android application and a machine learning algorithm. The developed system applied to washing machine analyses and judges the four-kinds of appliance’s status such as staying, washing, rinsing and spin-drying. The measurements of sensor and transmission of sensing data are operated on an Arduino board and the data are transmitted to cloud server in real time. The collected data are parsed by an Android application and injected into the machine learning algorithm for learning the status of the appliances. The machine learning algorithm compares the stored learning data with collected real-time data from the appliances. Our results are expected to contribute as a base technology to design an automatic control system based on machine learning technology for household appliances in real-time.

  18. Hydrophilic structures for condensation management in appliances

    Science.gov (United States)

    Kuehl, Steven John; Vonderhaar, John J.; Wu, Guolian; Wu, Mianxue

    2016-02-02

    An appliance that includes a cabinet having an exterior surface; a refrigeration compartment located within the cabinet; and a hydrophilic structure disposed on the exterior surface. The hydrophilic structure is configured to spread condensation. The appliance further includes a wicking structure located in proximity to the hydrophilic structure, and the wicking structure is configured to receive the condensation.

  19. Modeling of GE Appliances: Cost Benefit Study of Smart Appliances in Wholesale Energy, Frequency Regulation, and Spinning Reserve Markets

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Jason C.; Parker, Graham B.

    2012-12-31

    This report is the second in a series of three reports describing the potential of GE’s DR-enabled appliances to provide benefits to the utility grid. The first report described the modeling methodology used to represent the GE appliances in the GridLAB-D simulation environment and the estimated potential for peak demand reduction at various deployment levels. The third report will explore the technical capability of aggregated group actions to positively impact grid stability, including frequency and voltage regulation and spinning reserves, and the impacts on distribution feeder voltage regulation, including mitigation of fluctuations caused by high penetration of photovoltaic distributed generation. In this report, a series of analytical methods were presented to estimate the potential cost benefit of smart appliances while utilizing demand response. Previous work estimated the potential technical benefit (i.e., peak reduction) of smart appliances, while this report focuses on the monetary value of that participation. The effects on wholesale energy cost and possible additional revenue available by participating in frequency regulation and spinning reserve markets were explored.

  20. The impact of personality on adult patients' adjustability to orthodontic appliances.

    Science.gov (United States)

    Cooper-Kazaz, Rena; Ivgi, Inbal; Canetti, Laura; Bachar, Eytan; Tsur, Boaz; Chaushu, Stella; Shalish, Miriam

    2013-01-01

    To evaluate the impact of psychological traits on patients' choice of orthodontic appliances and their adjustability to orthodontic treatment. The sample consisted of 68 adult patients divided into three groups (28 buccal, 19 lingual, and 21 clear aligners). Prior to treatment participants filled out the Brief Symptom Inventory to assess symptoms of mental distress and the Narcissistic Vulnerability Scale to assess narcissistic personality traits. During the first week after appliance delivery and on day 14, patients completed a Health-Related Quality of Life questionnaire to assess their perception of pain and four areas of dysfunction. The correlation between personality traits and patients' reaction to treatment was evaluated. Somatization was the only trait that affected the choice of lingual and clear aligner appliance. Reduced self-esteem regulation was associated with increased pain in all patients, while exploitation was associated with pain in lingual patients. Narcissistic vulnerability slightly influenced patients' adaptability to orthodontic appliances. Although adjustability to lingual appliances was the most difficult, only two parameters were affected by personality features. In the buccal group, adjustability was affected by numerous parameters. Adaptation to the clear aligner appliance was relatively uneventful and least affected by psychological features. Anxious individuals tend to prefer lingual and clear aligner appliances. The selection of lingual and clear aligner appliances governs the patient's response and recovery process, leaving little room for the effect of psychological features. On the other hand, the buccal appliance allows for greater impact of personality traits on adjustability.

  1. Mobile based Appliances switching using Bluetooth

    Science.gov (United States)

    Gupta, Sureshchandra J., Dr; Desai, Kalp; Gaikawad, Deepak; Pawar, Vijay N.; Gangal, Devendranath R.

    2008-04-01

    How many times do you have to get up from your desk to switch on your Air conditioner or fan when you are completely into your table work? How many times do you feel lazy to get off your comfort to switch on/off your home appliances in different rooms? How much energy do you lose in a day for operating your appliances? The solution is either a large amount of manual work—or the idea that is presented over here: APP-CON (APP-CON stands for appliances control). Here the ordinary cell phone with bluetooth capability acts as remote designed in such a manner that it acts as a helping hand to human by reducing its manual work and therefore saving human energy. The cell phone control of APP-CON units lets you access many of your home appliances situated in different rooms by using just a single remote from distance. Electronics hobbyists would love to make such a remote control themselves. But they find it difficult due to complex circuitry rather than the high cost because of using a number of frequency counting techniques and decade counters. The APP-CON system given here overcomes the aforesaid problems by using a single microcontroller and moreover a simple program or software for bluetooth enabled cell phone and employing simple coding and decoding of remote signals. Here the mobile based remote control is used to operate a number of home appliances basically consists of Bluetooth technology. The unit consists of a transmitter and a receiver consisting of a microcontroller. The importance of bluetooth technology is that the signal to be transmitted from transmitter to the receiver is done without requiring line of sight.

  2. Econometric Modeling: An Application to the Demand for Electricity ...

    African Journals Online (AJOL)

    The empirical results show an inverse relationship between real appliance purchase price, the real per capita income and the demand for electricity. Also the rate of population growth rate as a proxy for electricity consumers appears to be insignificant. This reveals the clear fact that the demand for electricity is greater than ...

  3. Occlus-o-Guide® versus Andresen activator appliance: neuromuscular evaluation.

    Science.gov (United States)

    Farronato, Giampietro; Giannini, Lucia; Galbiati, Guido; Grillo, Elena; Maspero, Cinzia

    2013-05-20

    The aim of the present study was to assess the muscular variations at the electromyography (EMG) level for the anterior temporalis muscles and masseter muscles during treatment with Occlus-o-Guide® and Andresen activator appliances. Eighty-two patients (35 males and 47 females) aged between 8 and 12 years (mean age, 10.5±0.8 years) participated in the study. Fifty patients underwent treatment with an Occlus-o-Guide® and 32 patients with an Andresen activator. All patients underwent EMG examination using a Freely EMG (De Gotzen, Legnano, Italy) and surface bipolar electrodes when the appliances were worn for the first time (T0), and after 6 months (T1) and after 12 months (T2) of appliance use. Statistical analysis showed that both at T0 and T2, the percent overlapping coefficient (POC) of the anterior temporalis muscles was not statistically different between the appliance groups. At T0, the POC of the masseter muscles was significantly lower for the Andresen appliance as compared to the Occlus-o-Guide® (p=0.02), while at T2 this significance was lost. At insertion of an appliance, all patients show neuromuscular balance that does not correspond to orthognathic occlusion. Both appliances work by creating muscular imbalance. With the appliances in situ, EMG responses were generally analogous for the Occlus-o-Guide® and the Andresen activator; however, the imbalance was greater and the recovery of the orthological muscular balance was slower in patients under treatment with the Andresen activator as compared to those with the Occlus-o-Guide®.

  4. Modeling of electricity savings in the Danish household sector using Balmorel

    DEFF Research Database (Denmark)

    Trivella, Alessio; Baldini, Mattia

    In this paper we examine the investments in energy-efficient household appliances from an energy system perspective. We consider a set of ten appliances constituting the majority of the electricity consumption in the private household sector, and investigate whether investing in improved energy...... efficiency can compete with the cost of electricity supply from existing or new power plants. To assess the analysis, Balmorel, a linear optimization model for heat and power sectors, has been extended in order to assess the best possible investments in more efficient household appliances. The model is non......-exclusively tested on the Danish energy system under different scenarios, and computational experiments show that several energy efficiency measures in the household sector should be regarded as valuable investments, while others would require some form of support to become profitable. The analysis also reveals...

  5. 14 CFR 3.5 - Statements about products, parts, appliances and materials.

    Science.gov (United States)

    2010-01-01

    ..., appliances and materials. 3.5 Section 3.5 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION DEFINITIONS GENERAL REQUIREMENTS § 3.5 Statements about products, parts, appliances... product, part, appliance or material. (b) Prohibition against fraudulent and intentionally false...

  6. Powering a Home with Just 25 Watts of Solar PV. Super-Efficient Appliances Can Enable Expanded Off-Grid Energy Service Using Small Solar Power Systems

    Energy Technology Data Exchange (ETDEWEB)

    Phadke, Amol A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jacobson, Arne [Schatz Energy Research Center, Arcata, CA (United States); Park, Won Young [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lee, Ga Rick [Schatz Energy Research Center, Arcata, CA (United States); Alstone, Peter [Univ. of California, Berkeley, CA (United States); Khare, Amit [Schatz Energy Research Center, Arcata, CA (United States)

    2015-04-01

    Highly efficient direct current (DC) appliances have the potential to dramatically increase the affordability of off-grid solar power systems used for rural electrification in developing countries by reducing the size of the systems required. For example, the combined power requirement of a highly efficient color TV, four DC light emitting diode (LED) lamps, a mobile phone charger, and a radio is approximately 18 watts and can be supported by a small solar power system (at 27 watts peak, Wp). Price declines and efficiency advances in LED technology are already enabling rapidly increased use of small off-grid lighting systems in Africa and Asia. Similar progress is also possible for larger household-scale solar home systems that power appliances such as lights, TVs, fans, radios, and mobile phones. When super-efficient appliances are used, the total cost of solar home systems and their associated appliances can be reduced by as much as 50%. The results vary according to the appliances used with the system. These findings have critical relevance for efforts to provide modern energy services to the 1.2 billion people worldwide without access to the electrical grid and one billion more with unreliable access. However, policy and market support are needed to realize rapid adoption of super-efficient appliances.

  7. Electricity Demand Forecasting Using a Functional State Space Model

    OpenAIRE

    Nagbe , Komi; Cugliari , Jairo; Jacques , Julien

    2018-01-01

    In the last past years the liberalization of the electricity supply, the increase variability of electric appliances and their use, and the need to respond to the electricity demand in the real time had made electricity demand forecasting a challenge. To this challenge, many solutions are being proposed. The electricity demand involves many sources such as economic activities, household need and weather sources. All this sources make hard electricity demand forecasting. To forecast the electr...

  8. Refrigerator Efficiency in Ghana: Tailoring an appliance markettransformation program design for Africa

    Energy Technology Data Exchange (ETDEWEB)

    Ben Hagan, Essel; Van Buskirk, Robert; Ofosu-Ahenkorah, Alfred; McNeil, Michael A.

    2006-02-28

    A simple replication of developed country applianceefficiency labels and standards is unlikely to be feasible in Ghana andmany other countries in Africa. Yet by creatively modifying the developedcountry appliance efficiency market transformation model, it should bepossible to achieve dramatic energy use reductions. As was true indeveloped countries in the previous two decades, refrigeration efficiencyimprovements provide the greatest energy savings potential in theresidential electricity sector in Ghana. Although Ghana, like manyAfrican countries may impose standards on imports since Ghana does nothave manufacturing facilities for appliances in country. This approachmay hurt some consumers who patronize a very diverse market of usedappliances imported from Europe. We discuss how meeting the challenges ofthe Ghanaian market will require modification of the usual energyefficiency labeling and standards paradigm. But once a refrigeratormarket transformation is accomplished in Ghana, we estimate an averageenergy savings potential of 550 kWh/refrigerator/year, and a monetarysavings of more than $35/refrigerator/year. We discuss how this modifiedrefrigerator efficiency market transformation may occur in the Ghanaiancontext. If successful, this market transformation is likely to be anexample for many other African countries.

  9. 46 CFR 108.645 - Markings on lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Markings on lifesaving appliances. 108.645 Section 108.645 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.645 Markings on lifesaving appliances. (a...

  10. 46 CFR 108.665 - Appliances for watertight integrity.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Appliances for watertight integrity. 108.665 Section 108.665 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Equipment Markings and Instructions § 108.665 Appliances for watertight integrity...

  11. Paper de recherche no. 28 Bis. Can negotiated agreements replace efficiency standards as an instrument for transforming the electrical appliance market?; Cahier de recherche no. 28. Les accords negocies peuvent-ils remplacer les normes de performance pour la transformation du marche de l'electromenager

    Energy Technology Data Exchange (ETDEWEB)

    Menanteau, Ph.

    2002-03-01

    Without reinforced energy saving policies, residential consumption of electricity will increase sharply over the next twenty years, in particular as a result of expected growth in the specific uses of electricity. The main problem is not a lack of energy efficient technologies, which do indeed exist for electrical appliances, but one of slow diffusion of existing technologies due to the weakness of the price signal and the purchasing behaviour of consumers. In association with energy labelling, minimum efficiency performance standards have proved to be very effective in stimulating technological progress and organizing market transformation. But standards also suffer from long and often difficult implementation periods because of the resistance of the industrial sector. For manufacturers, similar results could be obtained more easily and more rapidly with voluntary agreements because they introduce flexibility margins in the achievement of commitments. This paper analyses the specific advantages of voluntary agreements for improving energy efficiency in the domestic appliances sector. We conclude that voluntary agreements may be an effective instrument for market transformation in certain conditions, but the alternative of regulatory measures must remain a credible, realistic threat if voluntary agreements are to have a really significant impact on performance improvement. (author)

  12. New horizons in orthodontics & dentofacial orthopedics: fixed Twin Blocks & TransForce lingual appliances.

    Science.gov (United States)

    Clark, William John

    2011-01-01

    During the 20th century functional appliances evolved from night time wear to more flexible appliances for increased day time wear to full time wear with Twin Block appliances. The current trend is towards fixed functional appliances and this paper introduces the Fixed Twin Block, bonded to the teeth to eliminate problems of compliance in functional therapy. TransForce lingual appliances are pre-activated and may be used in first phase treatment for sagittal and transverse arch development. Alternatively they may be integrated with fixed appliances at any stage of treatment.

  13. Economics of appliance efficiency

    International Nuclear Information System (INIS)

    Tiedemann, K.H.

    2009-01-01

    Several significant developments occurred in 2001 that affect the impact of market transformation programs. This paper presented and applied an econometric approach to the identification and estimation of market models for refrigerators, clothes washers, dishwashers and room air conditioners. The purpose of the paper was to understand the impact of energy conservation policy developments on sales of energy efficient appliances. The paper discussed the approach with particular reference to building a database of sales and drivers of sales using publicly available information; estimation of the determinants of sales using econometric models; and estimation of the individual impacts of prices, gross domestic product (GDP) and energy conservation policies on sales using regression results. Market and policy developments were also presented, such as change a light, save the world promotion; the California energy crisis; and the Pacific Northwest drought induced hydro power shortage. It was concluded that an increase in GDP increased the sales of both more efficient and less efficient refrigerators, clothes washers, dishwashers, and room air conditioners. An increase in electricity price increased sales of Energy Star refrigerators, clothes washers, dishwashers, and room air conditioners. 4 refs., 8 tabs.

  14. Saturation, energy consumption, CO{sub 2} emission and energy efficiency from urban and rural households appliances in Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Rosas-Flores, Jorge Alberto; Rosas-Flores, Dionicio [Division de Estudios de Posgrado, Facultad de Ingenieria, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria Coyoacan 04510, Mexico, DF (Mexico); Posgrado de Arquitectura, Facultad de Arquitectura, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria Coyoacan 04510, Mexico, DF (Mexico); Galvez, David Morillon [Posgrado de Arquitectura, Facultad de Arquitectura, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria Coyoacan 04510, Mexico, DF (Mexico); Instituto de Ingenieria, Universidad Nacional Autonoma de Mexico, Ciudad, Universitaria, Coyoacan 04510, Mexico, DF (Mexico)

    2011-01-15

    Energy usage and energy efficiency are of increasing concern in Mexico, electricity generation principally depends upon fossil fuels. On one hand, the stocks of these fuels have been confirmed to be critically limited. On the other hand, in process of electricity generation by means of these fuels, a number of poisonous by-products adversely affect the conservation of natural eco-system. This paper focuses on estimation of energy consumption, energy savings, reduction of emissions of CO{sub 2} for use of urban and rural household appliances in Mexico between 1996 and 2021. The analysis concentrates on six major energy end uses in the residential sector: refrigerators, air conditioners, washing machines, TV set, iron and heater. It is estimated that by 2021 there will be a cumulative saving of 22,605 GWh, as a result of the implementation of government programs on energy efficiency that represents a cumulative reduction of CO{sub 2} emissions of 15,087 Tg CO{sub 2}. It means that Mexico can reduce in 5650 MW the generation capacity of national electricity system, which is to avoid burning 40.35 MM barrels of oil. The findings can be useful to policy makers as well as household appliances users. (author)

  15. 46 CFR 167.15-28 - Inspection of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... SCHOOLS PUBLIC NAUTICAL SCHOOL SHIPS Inspections § 167.15-28 Inspection of lifesaving appliances and arrangements. The inspection of lifesaving appliances and arrangements must be in accordance with the... 46 Shipping 7 2010-10-01 2010-10-01 false Inspection of lifesaving appliances and arrangements...

  16. Treatment of adolescent patients with class II division 1 malocclusion using Eruption guidance appliance: A comparative study with Twin-block and Activator-Headgear appliances.

    Science.gov (United States)

    Nilsson, Jenny Jiayan Luo; Shu, Xiaochen; Magnusson, Britt Hedenberg; Burt, Idil Alatli

    2016-01-01

    The aim of this study was to evaluate the compliance and short-term effects of eruption guidance appliance (EGA) in adolescents with class II division 1 malocclusion in comparison with twin-block appliance (TBA) and activator-headgear appliance (A-HG). Dental records of 1886 patients were viewed in this retrospective study 129 patients treated with one of these three functional appliances were identified. 123 fulfilled the inclusion criteria and data were extracted from the dental records. Gender, age, compliance, overjet change at every visit, number of appliance breakages and number of emergency visits apart from appliance breakage were studied. The data were analyzed with Chi-square test, General Linear Model and Fisher scoring test. Results showed that 47 patients were treated with EGA, 38 patients with TBA and 38 patients with A-HG. Mean ages starting the treatment were slightly lower with EGA (11.5 years) than with TBA (12.3 years) and A-HG (11.8 years). Non-compliance was higher in the EGA group (31.9%) than TBA group (26.3%) and A-HG group (23.7%). Mean overjet reduction per month was 0.6 mm for EGA which was lower than TBA group (0.7 mm) and A-HG groups (0.7 mm).The number of emergency visits and appliance breakage were lower in EGA group. However, there was no statistically significant difference between the 3 groups regarding ages,compliance, mean overjet reduction, emergency visits and appliance breakage aspects. In conclusion, this study indicates that EGA is an alternative choice in the treatment of adolescent patients with class II division 1 malocclusion. However, long-term follow-up and cephalometric prospective study should be performed to continue our understanding more about the mechanisms of EGA and more definite conclusions can be made.

  17. 49 CFR 238.230 - Safety appliances-new equipment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Safety appliances-new equipment. 238.230 Section... I Passenger Equipment § 238.230 Safety appliances—new equipment. (a) Applicability. This section..., 2007, that is equipped with a safety appliance, required by the “manner of application” provisions in...

  18. Esthetic perception of orthodontic appliances by Brazilian children and adolescents.

    Science.gov (United States)

    Kuhlman, Deise Caldas; Lima, Tatiana Araújo de; Duplat, Candice Belchior; Capelli, Jonas

    2016-01-01

    The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher economic status, golden orthodontic brackets and

  19. EPA ENERGY STAR: Tackling Growth in Home Electronics and Small Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, Marla Christine; Brown, Richard; Homan, Gregory

    2008-11-17

    Over a decade ago, the electricity consumption associated with home electronics and other small appliances emerged onto the global energy policy landscape as one of the fastest growing residential end uses with the opportunity to deliver significant energy savings. As our knowledge of this end use matures, it is essential to step back and evaluate the degree to which energy efficiency programs have successfully realized energy savings and where savings opportunities have been missed.For the past fifteen years, we have quantified energy, utility bill, and carbon savings for US EPA?s ENERGY STAR voluntary product labeling program. In this paper, we present a unique look into the US residential program savings claimed to date for EPA?s ENERGY STAR office equipment, consumer electronics, and other small household appliances as well as EPA?s projected program savings over the next five years. We present a top-level discussion identifying program areas where EPA?s ENERGY STAR efforts have succeeded and program areas where ENERGY STAR efforts did not successfully address underlying market factors, technology issues and/or consumer behavior. We end by presenting the magnitude of ?overlooked? savings.

  20. Increased BMI in children-an indicator for less compliance during orthodontic treatment with removable appliances.

    Science.gov (United States)

    von Bremen, Julia; Lorenz, Nathalie; Ludwig, Björn; Ruf, Sabine

    2018-02-19

    To assess whether or not childhood overweight is associated with lower levels of compliance during orthodontic therapy with removable appliances. Starting in 2011, all upper expansion plates and Sander II appliances were equipped with a Theramon® microsensor chip to assess appliance wear time objectively. According to their pre-treatment, BMI normal weight patients were matched to consecutively treated overweight or obese patients by gender, age, and appliance type. Cooperation was assessed with microelectronic wear time documentation over a period of at least 6 months. A total of 50 patients (25 overweight, 25 normal weight) with upper expansion plates and 64 patients (32 overweight, 32 normal weight) with Sander II appliances were analysed. Spearman Rho coefficients showed an indirect association between BMI and appliance wear time, indicating that the higher the BMI, the less the patients wore their appliances (P appliances (P appliance wear during orthodontic treatment with removable appliances. Additional factors which influenced cooperation during treatment with removable appliances were patient age and appliance type.

  1. Effective Maxillary Protraction with Tandem Traction Bow Appliance

    Directory of Open Access Journals (Sweden)

    Pravin Kumar S Marure

    2014-01-01

    Full Text Available Tandem traction bow appliance (TTBA promotes patient compliance, because it is more esthetic and comfortable than extraoral appliances. TTBA should be used only in case where maxillary deficiency and normal mandible is present. Advantages of it includes good oral hygiene, early treatment of any Class III malocclusion, optimal retention, distribution of the forces for protraction to all maxillary teeth, free mandibular movement. It can be used in conjunction with fixed appliances if necessary. This paper includes two case reports. The treatment results in both the cases demonstrated significant skeletal and dental response to TTBA therapy. Skeletal change was primarily a result of anterior movement of the maxilla.

  2. Fixed functional appliances with multibracket appliances have no skeletal effect on the mandible: A systematic review and meta-analysis.

    Science.gov (United States)

    Ishaq, Ramy Abdul Rahman; AlHammadi, Maged Sultan; Fayed, Mona M S; El-Ezz, Amr Abou; Mostafa, Yehya

    2016-05-01

    Our aim was to assess the skeletal mandibular changes (anteroposterior and vertical) in circumpubertal patients with fixed functional appliances installed on multibracket appliances compared with untreated patients. An open-ended electronic search of 4 databases (PubMed, Embase, Cochrane Library, and Web of Science) up to April 2014 was performed. Additional searches of relevant journals, reference lists of the retrieved articles, systematic reviews, and gray literature were performed. Specific inclusion and exclusion criteria were applied to identify relevant articles. Quality was evaluated using the Cochrane Collaboration risk of bias tool and the Newcastle-Ottawa scale for prospective controlled clinical trials. Meta-analyses were conducted with fixed and random effects models as appropriate. Statistical heterogeneity was also examined. Seven articles were included in the qualitative synthesis and 5 in the meta-analysis. The included randomized controlled trials were at high risk of bias, and the methodologic quality of the prospective controlled clinical trials was high. Based on assessment of the fixed functional appliance phase in isolation, no difference in mandibular anteroposterior positional changes (SNB angle) (standard mean difference, 0.11°; 95% CI, -0.28, 0.50) was found between the treated and control groups. The vertical dimension was not influenced by the fixed functional appliance treatment. There is little high-quality evidence concerning the relative influence of fixed functional appliances on skeletal and dentoalveolar changes. However, based on the limited evidence, it appears that they have little effect on the skeletal mandibular parameters. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  3. 49 CFR 236.207 - Electric lock on hand-operated switch; control.

    Science.gov (United States)

    2010-10-01

    ..., AND APPLIANCES Automatic Block Signal Systems Standards § 236.207 Electric lock on hand-operated switch; control. Electric lock on hand-operated switch shall be controlled so that it cannot be unlocked... 49 Transportation 4 2010-10-01 2010-10-01 false Electric lock on hand-operated switch; control...

  4. Esthetic perception of orthodontic appliances by Brazilian children and adolescents

    Science.gov (United States)

    Kuhlman, Deise Caldas; de Lima, Tatiana Araújo; Duplat, Candice Belchior; Capelli, Jonas

    2016-01-01

    ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276) was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those with higher

  5. Esthetic perception of orthodontic appliances by Brazilian children and adolescents

    Directory of Open Access Journals (Sweden)

    Deise Caldas Kuhlman

    Full Text Available ABSTRACT Objective: The objective of this present study was to understand how children and adolescents perceive esthetic attractiveness of a variety of orthodontic appliances. It also analyzed preferences according to patients' age, sex and socioeconomic status. Methods: A photograph album consisting of eight photographs of different orthodontic appliances and clear tray aligners placed in a consenting adult with pleasing smile was used. A sample of children or adolescents aged between 8 and 17 years old (n = 276 was asked to rate each image for its attractiveness on a visual analog scale. Comparisons between the appliances attractiveness were performed by means of nonparametric statistics with Friedman's test followed by Dunn's multiple comparison post-hoc test. Correlation between appliances and individuals' socioeconomic status, age, sex, and esthetic perception was assessed by means of Spearman's correlation analysis. Results: Attractiveness ratings of orthodontic appliances varied nonsignificantly for children in the following hierarchy: traditional metallic brackets with green elastomeric ligatures > traditional metallic brackets with gray elastomeric ligatures > sapphire esthetic brackets; and for adolescents, as follows: sapphire esthetic brackets > clear aligner without attachments > traditional metallic brackets with green elastomeric ligatures. The correlation between individuals' socioeconomic status and esthetic perception of a given appliance was negative and statistically significant for appliances such as the golden orthodontic brackets and traditional metallic brackets with green elastomeric ligatures. Conclusion: Metal appliances were considered very attractive, whereas aligners were classified as less attractive by children and adolescents. The correlation between esthetic perception and socioeconomic status revealed that individuals with a higher socioeconomic level judged esthetics as the most attractive attribute. For those

  6. Effect of Fixed Metallic Oral Appliances on Oral Health.

    Science.gov (United States)

    Alnazzawi, Ahmad

    2018-01-01

    There is a substantial proportion of the population using fixed metallic oral appliances, such as crowns and bridges, which are composed of various dental alloys. These restorations may be associated with a number of effects on oral health with variable degrees of severity, to review potential effects of using fixed metallic oral appliances, fabricated from various alloys. The MEDLINE/PubMed database was searched using certain combinations of keywords related to the topic. The search revealed that burning mouth syndrome, oral pigmentation, hypersensitivity and lichenoid reactions, and genotoxic and cytotoxic effects are the major potential oral health changes associated with fixed prosthodontic appliances. Certain oral disorders are associated with the use of fixed metallic oral appliances. Patch test is the most reliable method that can be applied for identifying metal allergy, and the simultaneous use of different alloys in the mouth is discouraged.

  7. Achievement report for fiscal 1998 on development of advanced household electric appliance recycling technology; 1998 nendo senshinteki kaden recycle gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop a household electric appliance recycling technology, research and development has been made on crushing of compressors, separation of resins and metals, and regenerative utilization of urethane used as the refrigerator heat insulating material. In the compressor crushing technology, development was made on a ring hammer crusher of wood pattern horizontal type. In the research of the resin-metal separation technology, the dry-type separation and material purity were enhanced successfully by means of classification of materials to be crushed according to grain sizes, and classification using an eddy current screening device and a specific gravity screening device. In the research of the urethane regenerative utilization technology, the contained fluorocarbon was decomposed at the rate of 99.999% by modifying and rinsing the pyrolytic gas from the urethane by means of cracking, having achieved to make the material innocuous. The fuel gas thus obtained can be utilized for electric power generation. In addition, a method to granulate the material was established by mixing it with thermo-plastic resins. It was discovered that using the recovered urethane, which is pulverized smaller than 300 {mu} m, can elevate the heat insulation performance when it is used as the vacuum heat insulator, proving its capability of being re-utilized in refrigerators. (NEDO)

  8. Use of appliances in stand-alone PV power supply systems: problems and solutions. Task 3 use of photovoltaic power systems in stand-alone and island applications

    Energy Technology Data Exchange (ETDEWEB)

    Vallve, X.; Gafas, G. [IEA PVPS, Task 3 (Spain); Villoz, M. [IEA PVPS, Task 3 (Switzerland); Wilshaw, A. [IEA PVPS, Task 3 (United Kingdom); Jacquin, P. [IEA PVPS, Task 3 (France)

    2002-09-15

    In Stand-Alone Photovoltaic Systems (SAPV systems), special attention must be paid to the used appliances and loads. Inappropriate loads are very often the origin of PV system malfunction or failure. Start-up power peaks, or reactive power and harmonic distortion can cause system signal instability and protective devices will close the system down. A well-matched load together with a carefully selected choice of appliances can lead to significant savings in terms of reduced need for PV and electricity storage capacity. Conversely, inefficient appliances and processes, standby loads and inappropriate loads will increase the requirement for expensive PV and storage capacity. This paper presents a survey of real cases with load related problems in worldwide applications, their effect on quality and cost of the service and the solutions that were adopted and suggested alternative solutions. One of the main conclusions of the work is the importance to integrate the choice of the appliance while designing the SAPV system. (author)

  9. A modified, lingually supported cantilevered Herbst appliance.

    Science.gov (United States)

    Snodgrass, D

    1996-01-01

    This new, fixed-functional appliance/Herbst/Bioprogressive system is designed for patient comfort and mandatory compliance. It also combines the positive clinical effects of four fixed-functional systems. It allows rapid palatal expansion of the upper arch, alveolar uprighting of the lower arch, upper and lower incisor alignment, and sagittal correction of Class II malocclusions to occur simultaneously with one appliance fixed in both arches. It is indicated for use in growing patients with skeletal Class II malocclusions. The ideal timing for treatment is the late mixed dentition. Being able to remove the appliance after one year with the upper second bicuspids erupting slightly Class III so the clinician can immediately begin fixed finishing mechanics would be ideal. This new Herbst design will reduce the frequency of orthognathic surgery and upper bicuspid extraction to camouflage Class II malocclusions. At the same time, it gives total control to the clinician in treating some more difficult, non-compliant patients. Fixed-functional appliances, which improve treatment efficiency and treatment results and provide for patient comfort, while at the same time give the treating clinician almost total control of the three planes of facial growth will open new doors for orthodontic treatment and research in the next century.

  10. Electricity Profile Study for Domestic and Commercial Sectors

    OpenAIRE

    Asmarashid Ponniran; Nur Azura Mamat; Ariffudin Joret

    2012-01-01

    As Malaysia move towards as a developed country, it is expected that the electricity consumption in domestic and commercial sectors will increase as well as more industrials and households need. This study is to investigate the electricity profile in domestic and commercial sectors by monitoring some appropriate appliances that contribute high electricity consumption. The characteristics for every major loads are examined and the potential energy saving is compared to an efficient electrical ...

  11. Efficacy of custom made oral appliance for treatment of obstructive sleep apnea

    Directory of Open Access Journals (Sweden)

    V R Cilil

    2015-01-01

    Full Text Available Introduction: oral appliance for the treatment of OSA is considered as an effective, low-risk alternative to CPAP. Demand for oral appliance increases as an alternative for those who cannot tolerate CPAP and refuse surgery. Oral appliances uses the traditional methods to advance the mandible thus modify the posture and their by enlarge the airway or otherwise reduce the collapsibility. Aims and Objectives: The main objective of this study was to evaluate the efficacy of custom made oral appliance on sleep characteristics of OSA patients. Materials and Methods: Polysomnography was done on 15 patients of 24-60 years of age before (T1, and after the delivery of the custom made oral appliance (T2. Statistical Analysis: Paired t tests were performed to determine the significance of change in the polysomnographic and cephalometric variables. P < 0.05 was considered as significant. Results: All patients with oral appliance showed an improvement in sleep parameters with an increase in sleep efficiency, and desaturation index with the use of oral appliance. ESS and cephalometric findings showed improvement in the sleep apnea in concordance with the sleep parameters. Conclusions: Custom made oral appliance is a useful treatment option for improving quality of sleep and can be considered as an alternative treatment modality.

  12. Household consumption of different generations. Purchase of electric appliances and energy; Hushaallens konsumtion i olika generationer. Inkoep av eldriven hushaallsutrustning och energi

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson-Kanyama, Annika; Stenerus, Ann-Sofie

    2008-02-15

    Considering that energy efficiency is an important task for the future, this study shows to what extent generation affiliation and other household characteristics affect consumption of primarily electrical household appliances and energy. The material used is a number of studies concerning household expenditures as well as average prices for goods and energy. Material from 1958, 1978, 1985, 1995 and 2003-2005 have been used. This report also includes a discussion regarding opportunities for energy efficiency. The term generation is explained in this context and earlier studies with relevance to generation affiliation and energy are summarized. An analysis of consumption habits among different generations highlights that the generations living in Sweden today experienced substantially different consumption opportunities during childhood and youth. Some generations have memories of much lower consumption levels, memories which could be recalled with the right policy instruments. The consumption experiences of the veteran generation are studied from 1958 up to 2003-2005, and this study also includes a comparison between the consumption levels in families with children in the 1950s and today. The current Swedish population have very different frames of reference concerning possible consumption styles. However, no generation would easily accept a more energy efficient lifestyle, because all generations have adapted to the increased consumption opportunities with high mobility and easy access. The analysis of household purchases of electrical appliances is based on information from 6 700 households (2003-2005) and 4 400 households (1985). The results are both surprising and expected. Generation affiliation is important for explaining expenditure levels for equipment for entertainment and information, where the youngest generations spend the most. But there are also differences related to gender as well as differences related to income and dwelling type. The differences

  13. Home electrical system safety in Italy

    Energy Technology Data Exchange (ETDEWEB)

    Auditor,

    1990-06-01

    Italy, amongst the industrialized countries, has the highest mortality rate due to accidents associated with the improper use or maintenance of home electrical systems. The increasing use of domestic electrical appliances has raised the risk of accidents, especially in homes equipped with out-dated, low-capacity electrical plants and worn wiring. Within this context, this paper reports on the results of survey to establish the worthiness and type of electrical systems in use in a sample of 1,000 residential buildings. The paper then assesses the efficacy of recent normatives designed to increase the safety and efficiency of home electrical installations.

  14. A comparison between indirect and objective wear-time assessment of removable orthodontic appliances.

    Science.gov (United States)

    Schott, Timm C; Meyer-Gutknecht, Hannes; Mayer, Nicolai; Weber, Joachim; Weimer, Katja

    2017-04-01

    Patients do not always adhere to the wear times prescribed for removable orthodontic appliances. We evaluated the validity and usability of indirect wear-time assessment methods by comparing wear-time estimates with microelectronically measured wear times in patients with removable orthodontic appliances. Wear times of 33 expansion plates, 34 functional appliances, and 42 retention plates of patients aged 6-20 years (12.3±2.9 years, 50.5% female) were indirectly determined by practitioners using a questionnaire assessing five parameters on a 5-point Likert scale: appliance handling, appliance appearance, bite shift, tooth movement, and appliance fit. The perceived difficulty in assessing each parameter was rated. Actual wear times were evaluated with microelectronic sensors in the appliances. Regression analyses revealed that practitioners' decisions about wear times varied depending on the type of appliance and criteria used, with only one standard criterion best predicting estimated wear time for each appliance. Different standard criteria were better predictors of measured wear time: 22.3% of wear-time variability was explained by expansion plate appearance, 31.2% by functional appliance handling, and 18.8% by retainer fitting. However, practitioners rated the difficulty of assessment in most cases as 'easy'. The study was not double blinded for technical reasons, and practitioners may have considered the evaluation criteria more carefully than in normal daily practice. Practitioners' decisions about wear times based on standard criteria strongly vary depending on the type of appliance and criteria used. © The Author 2016. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

  15. The use of functional appliances in contemporary orthodontic practice.

    Science.gov (United States)

    DiBiase, A T; Cobourne, M T; Lee, R T

    2015-02-16

    Functional appliances have been used for over 100 years in orthodontics to correct Class II malocclusion. During this time numerous different systems have been developed often accompanied by claims of modification and enhancement of growth. Recent clinical evidence has questioned whether they really have a lasting influence on facial growth, their skeletal effects appearing to be short term. However, despite these findings, the clinical effectiveness of these appliances is acknowledged and they can be very useful in the correction of sagittal arch discrepancies. This article will discuss the clinical use of functional appliances, the underlying evidence for their use and their limitations.

  16. 33 CFR 150.507 - How must the operator service inflatable lifesaving appliances?

    Science.gov (United States)

    2010-07-01

    ... inflatable lifesaving appliances? 150.507 Section 150.507 Navigation and Navigable Waters COAST GUARD... Specialty Equipment Inflatable Lifesaving Appliances § 150.507 How must the operator service inflatable lifesaving appliances? (a) The operator must service each inflatable liferaft according to 46 CFR subpart 160...

  17. Face and neck dermatitis from a stainless steel orthodontic appliance.

    Science.gov (United States)

    Ehrnrooth, Minna; Kerosuo, Heidi

    2009-11-01

    Although nickel is the most common cause of contact allergy, nickel-containing orthodontic appliances seldom cause adverse reactions that result in discontinuation of treatment. We report on an eruption of dermatitis in the face and neck of an adult female patient after placement of a rapid maxillary expansion appliance (RME). Because the patient suspected nickel allergy, her tolerance to the appliance material was tested intraorally before treatment by cementing bands on four teeth for a week. No visible adverse reactions were seen during the test. One week after cementation of the RME appliance, the patient reported strong itching of the face and a red rash. Clinical examination showed itchy papular erythema on the face and neck. No intraoral reactions or symptoms were present. The RME appliance was removed, and symptoms disappeared in 4 to 5 days. The patient was referred for a nickel patch test, which gave a strong positive result. Adverse patient reactions of potential allergic origin should be diagnosed carefully, and their possible impact on further treatment should be evaluated accordingly.

  18. An Iterative Load Disaggregation Approach Based on Appliance Consumption Pattern

    Directory of Open Access Journals (Sweden)

    Huijuan Wang

    2018-04-01

    Full Text Available Non-intrusive load monitoring (NILM, monitoring single-appliance consumption level by decomposing the aggregated energy consumption, is a novel and economic technology that is beneficial to energy utilities and energy demand management strategies development. Hardware costs of high-frequency sampling and algorithm’s computational complexity hampered NILM large-scale application. However, low sampling data shows poor performance in event detection when multiple appliances are simultaneously turned on. In this paper, we contribute an iterative disaggregation approach that is based on appliance consumption pattern (ILDACP. Our approach combined Fuzzy C-means clustering algorithm, which provide an initial appliance operating status, and sub-sequence searching Dynamic Time Warping, which retrieves single energy consumption based on the typical power consumption pattern. Results show that the proposed approach is effective to accurately disaggregate power consumption, and is suitable for the situation where different appliances are simultaneously operated. Also, the approach has lower computational complexity than Hidden Markov Model method and it is easy to implement in the household without installing special equipment.

  19. Application of high-resolution domestic electricity load profiles in network modelling

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Mendaza, Iker Diaz de Cerio; Heiselberg, Per Kvols

    2016-01-01

    the generated profiles are inputted in a low-voltage network model created in DIgSILENT PowerFactory. By means of employing 1 hour based demand and generation profiles in during dynamic studies, the representation of the local power system performance might sometimes not be as accurate as needed. In the test...... with modeling when 1-minute domestic electricity demand and generation profiles are used as inputs. The analysis is done with a case study of low-voltage network located in Northern Denmark. The analysis includes two parts. The first part focuses on modeling the domestic demands and on-site generation in 1......-minute resolution. The load profiles of the household appliances are created using a bottom-up model, which uses the 1-minute cycle power use characteristics of a single appliance as the main building block. The profiles of heavy electric appliances, such as heat pump, are not included in the above...

  20. Aseismatic design of electrical equipments and instruments for nuclear power stations

    International Nuclear Information System (INIS)

    Suzuki, Yasuharu; Nishizawa, Kazuo; Miyazaki, Yoshio; Miura, Takumi

    1977-01-01

    The aseismatic design of electrical instruments is carried out according to IEEE Standard 344-1971 in the USA. In Japan also, the method of aseismatic design of electrical instruments has been investigated by the representatives of electric power companies and electric machine makers since 1972. In Hitachi Ltd., the statical method of confirming aseismatic property was established on the basis of the rigid design for electrical instruments. It is convenient to examine the aseismatic property of electrical equipments by classifying them into control and switch boards, electrical appliances, equipments and circuits. It is possible to use the static method treating earthquake force as static load by avoiding resonance with the electrical equipments which have the higher natural frequency than that of buildings. The purposes of the vibration test are to prove the validity of the theoretical analysis, to clarify the vibration characteristics, and to confirm the maintenance of functions and the strength of the equipments. The vibration tests of control boards, the switch boards of enclosed type, motor control centers, the racks for instrumentation, storage batteries and electrical appliances are explained. Moreover, the vibration analysis with a computer according to finite element method is described. (Kako, I.)

  1. 46 CFR 58.16-20 - Ventilation of compartments containing gas-consuming appliances.

    Science.gov (United States)

    2010-10-01

    ... appliances. 58.16-20 Section 58.16-20 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED... and Heating § 58.16-20 Ventilation of compartments containing gas-consuming appliances. (a) Compartments containing gas-consuming appliances which are located above the weather deck shall be fitted with...

  2. An assessment of household electricity load curves and corresponding CO2 marginal abatement cost curves for Gujarat state, India

    International Nuclear Information System (INIS)

    Garg, Amit; Shukla, P.R.; Maheshwari, Jyoti; Upadhyay, Jigeesha

    2014-01-01

    Gujarat, a large industrialized state in India, consumed 67 TWh of electricity in 2009–10, besides experiencing a 4.5% demand–supply short-fall. Residential sector accounted for 15% of the total electricity consumption. We conducted load research survey across 21 cities and towns of the state to estimate residential electricity load curves, share of appliances by type and usage patterns for all types of household appliances at utility, geographic, appliance, income and end-use levels. The results indicate that a large scope exists for penetration of energy efficient devices in residential sector. Marginal Abatement Cost (MAC) curves for electricity and CO 2 were generated to analyze relative attractiveness of energy efficient appliance options. Results indicate that up to 7.9 TWh of electricity can be saved per year with 6.7 Mt-CO 2 emissions mitigation at negative or very low CO 2 prices of US$ 10/t-CO 2 . Despite such options existing, their penetration is not realized due to myriad barriers such as financial, institutional or awareness and therefore cannot be taken as baseline options for CO 2 emission mitigation regimes. - Highlights: • Residential sector provides focused mitigation opportunities. • Energy efficient space cooling is the main technology transition required. • Almost 26% residential load could be reduced by DSM measures. • Myriad barriers limit penetration of negative marginal cost efficient options

  3. Colostomies and the use of colostomy appliances.

    Science.gov (United States)

    Cronin, Elaine

    The surgical formation of a colostomy is indicated as part of the treatment of various conditions, primarily colon cancer, requiring the patient (ostomist) to wear a colostomy pouch. Today's stoma appliances bear no resemblance to those worn three or four decades ago when colostomy, ileostomy and urostomy bags were made entirely from rubber. The patient, who would have two to three bags in circulation at a time, would interchange them allowing for the washing and drying of the previous one, thus minimizing odour and potential perishing of the rubber. The design of these appliances was simple, but they were large and bulky and the outlet resembled that of a hot-water bottle stopper or a cap from an old soda bottle that required the insertion of coinage (2p) to open it. This article explores the range of colostomy appliances and management options available to the nurse when caring for patients with a colostomy.

  4. Pyogenic granuloma: a rare side complication from an orthodontic appliance.

    Science.gov (United States)

    Acharya, Priti N; Gill, Daljit; Lloyd, Tim

    2011-12-01

    This case report discusses a rare side effect associated with the use ofa fixed quad helix orthodontic appliance. A 14-year-old healthy girl presented with a painful enlarging mass on her tongue, which was causing distress to both her and her parents. Investigations confirmed that the mass was a pyogenic granuloma and management involved surgical excision of the mass and removal of the quad helix appliance. At least once previous case associated with an orthodontic quad helix appliance has been reported in the literature.

  5. 33 CFR 81.20 - Lights and sound signal appliances.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights and sound signal appliances. 81.20 Section 81.20 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... appliances. Each vessel under the 72 COLREGS, except the vessels of the Navy, is exempt from the requirements...

  6. Effect of thermoplastic appliance thickness on initial stress distribution in periodontal ligament

    Directory of Open Access Journals (Sweden)

    De-Shin Liu

    2015-04-01

    Full Text Available A numerical investigation into the initial stress distribution induced within the periodontal ligament by thermoplastic appliances with different thicknesses is performed. Based on the plaster model of a 25-year-old male patient, a finite element model of the maxillary lateral incisors and their supporting structures is constructed. In addition, four finite element models of thermoplastic appliances with different thicknesses in the range of 0.5–1.25 mm are also constructed based on the same plaster model. Finite element analysis simulations are performed to examine the effects of the force delivered by the thermoplastic appliances on the stress response of the periodontal ligament during the elastic recovery process. The results show that the stress induced in the periodontal ligament increases with an increasing appliance thickness. For example, the stress triples from 0.0012 to 0.0038 MPa as the appliance thickness is increased from 0.75 to 1.25 mm. The results presented in this study provide a useful insight into as a result of the compressive and tensile stresses induced by thermoplastic appliances of different thicknesses. Moreover, the results enable the periodontal ligament stress levels produced by thermoplastic appliances of different thicknesses to be reliably estimated.

  7. Analyzing price and efficiency dynamics of large appliances with the experience curve approach

    International Nuclear Information System (INIS)

    Weiss, Martin; Patel, Martin K.; Junginger, Martin; Blok, Kornelis

    2010-01-01

    Large appliances are major power consumers in households of industrialized countries. Although their energy efficiency has been increasing substantially in past decades, still additional energy efficiency potentials exist. Energy policy that aims at realizing these potentials faces, however, growing concerns about possible adverse effects on commodity prices. Here, we address these concerns by applying the experience curve approach to analyze long-term price and energy efficiency trends of three wet appliances (washing machines, laundry dryers, and dishwashers) and two cold appliances (refrigerators and freezers). We identify a robust long-term decline in both specific price and specific energy consumption of large appliances. Specific prices of wet appliances decline at learning rates (LR) of 29±8% and thereby much faster than those of cold appliances (LR of 9±4%). Our results demonstrate that technological learning leads to substantial price decline, thus indicating that the introduction of novel and initially expensive energy efficiency technologies does not necessarily imply adverse price effects in the long term. By extending the conventional experience curve approach, we find a steady decline in the specific energy consumption of wet appliances (LR of 20-35%) and cold appliances (LR of 13-17%). Our analysis suggests that energy policy might be able to bend down energy experience curves. (author)

  8. The Risk of Residential Peak Electricity Demand: A Comparison of Five European Countries

    Directory of Open Access Journals (Sweden)

    Jacopo Torriti

    2017-03-01

    Full Text Available The creation of a Europe-wide electricity market combined with the increased intermittency of supply from renewable sources calls for an investigation into the risk of aggregate peak demand. This paper makes use of a risk model to assess differences in time-use data from residential end-users in five different European electricity markets. Drawing on the Multinational Time-Use Survey database, it assesses risk in relation to the probability of electrical appliance use within households for five European countries. Findings highlight in which countries and for which activities the risk of aggregate peak demand is higher and link smart home solutions (automated load control, dynamic pricing and smart appliances to different levels of peak demand risk.

  9. Incorporating experience curves in appliance standards analysis

    International Nuclear Information System (INIS)

    Desroches, Louis-Benoit; Garbesi, Karina; Kantner, Colleen; Van Buskirk, Robert; Yang, Hung-Chia

    2013-01-01

    There exists considerable evidence that manufacturing costs and consumer prices of residential appliances have decreased in real terms over the last several decades. This phenomenon is generally attributable to manufacturing efficiency gained with cumulative experience producing a certain good, and is modeled by an empirical experience curve. The technical analyses conducted in support of U.S. energy conservation standards for residential appliances and commercial equipment have, until recently, assumed that manufacturing costs and retail prices remain constant during the projected 30-year analysis period. This assumption does not reflect real market price dynamics. Using price data from the Bureau of Labor Statistics, we present U.S. experience curves for room air conditioners, clothes dryers, central air conditioners, furnaces, and refrigerators and freezers. These experience curves were incorporated into recent energy conservation standards analyses for these products. Including experience curves increases the national consumer net present value of potential standard levels. In some cases a potential standard level exhibits a net benefit when considering experience, whereas without experience it exhibits a net cost. These results highlight the importance of modeling more representative market prices. - Highlights: ► Past appliance standards analyses have assumed constant equipment prices. ► There is considerable evidence of consistent real price declines. ► We incorporate experience curves for several large appliances into the analysis. ► The revised analyses demonstrate larger net present values of potential standards. ► The results imply that past standards analyses may have undervalued benefits.

  10. Assessment of Literature Related to Combustion Appliance Venting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, Vi H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Singer, Brett C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Stratton, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wray, Craig P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    In many residential building retrofit programs, air tightening to increase energy efficiency is constrained by concerns about related impacts on the safety of naturally vented combustion appliances. Tighter housing units more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spillage. Several test methods purportedly assess the potential for depressurization-induced backdrafting and spillage, but these tests are not robustly reliable and repeatable predictors of venting performance, in part because they do not fully capture weather effects on venting performance. The purpose of this literature review is to investigate combustion safety diagnostics in existing codes, standards, and guidelines related to combustion appliances. This review summarizes existing combustion safety test methods, evaluations of these test methods, and also discusses research related to wind effects and the simulation of vent system performance. Current codes and standards related to combustion appliance installation provide little information on assessing backdrafting or spillage potential. A substantial amount of research has been conducted to assess combustion appliance backdrafting and spillage test methods, but primarily focuses on comparing short-term (stress) induced tests and monitoring results. Monitoring, typically performed over one week, indicated that combinations of environmental and house operation characteristics most conducive to combustion spillage were rare. Research, to an extent, has assessed existing combustion safety diagnostics for house depressurization, but the objectives of the diagnostics, both stress and monitoring, are not clearly defined. More research is also needed to quantify the frequency of test “failure” occurrence throughout the building stock and assess the statistical effects of weather (especially wind) on house depressurization and in turn on combustion appliance venting

  11. 21 CFR 888.3030 - Single/multiple component metallic bone fixation appliances and accessories.

    Science.gov (United States)

    2010-04-01

    ... appliances and accessories. 888.3030 Section 888.3030 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT....3030 Single/multiple component metallic bone fixation appliances and accessories. (a) Identification. Single/multiple component metallic bone fixation appliances and accessories are devices intended to be...

  12. 46 CFR 199.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... appliances and arrangements. 199.40 Section 199.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) LIFESAVING APPLIANCES AND ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS General § 199.40 Evaluation, testing and approval of lifesaving appliances and arrangements. (a) Each item of...

  13. Half a dollar per kWh and still cheap electricity

    International Nuclear Information System (INIS)

    Daey Ouwens, C.

    1991-01-01

    An analysis for the costs of electricity produced by an autonomous solar cell system in combination with efficient electric appliances, as they are used in houses and small offices, is presented. If efficient appliances are used, an average household will use about 700 kWh per year, compared to about 3000 kWh it is using on average at present. Efficient appliances, however, are more expensive. The extra cost per kWh saved is about the same as the cost of the fuel needed to produce a kWh in a power plant. The 700 kWh per year can be produced by an autonomous solar cell system with an area of 3 m 2 (efficiency 19%). The analysis is valid roughly for the area between 40 o northern and southern latitude. A comparison has been made between the total costs of a grid connection and the costs of an autonomous solar cell system. If all costs are capitalized and compiled, a grid connection will amount to about $6,000 (fuel costs are not included). The costs of a solar cell system producing 700 kWh per year are about the same or even lower. The modular nature of solar cell systems makes it possible to start with a certain number of appliances, depending on the amount of money one can spend. 6 tabs., 2 refs

  14. Convex stoma appliances: an audit of stoma care nurses.

    Science.gov (United States)

    Perrin, Angie

    2016-12-08

    This article observes the complexities surrounding the use of convex appliances within the specialist sphere of stoma care. It highlights some of the results taken from a small audit carried out with 24 stoma care nurses examining the general use of convex appliances and how usage of convex products has evolved, along with specialist stoma care practice.

  15. Survival of palatal miniscrews used for orthodontic appliance anchorage: a retrospective cohort study.

    Science.gov (United States)

    Karagkiolidou, Angeliki; Ludwig, Björn; Pazera, Pawel; Gkantidis, Nikolaos; Pandis, Nikolaos; Katsaros, Christos

    2013-06-01

    The purpose of this study was to examine the overall success of miniscrews inserted in the paramedian palatal region for support of various appliances during orthodontic treatment. The patients received 1 or 2 miniscrews in the paramedian anterior palate of 8.0-mm length and 1.6-mm diameter placed during orthodontic treatment by the same experienced orthodontist. In total, 196 patients (121 girls, 75 boys; median age, 11.7; interquartile range, 3.7) who received 384 miniscrews were evaluated. Two hundred four miniscrews were used with rapid palatal expansion appliances, 136 with appliances for distalization of posterior teeth, and 44 with other appliances, such as transpalatal arches for tooth stabilization. The overall survival of the miniscrews was excellent (97.9%) in the cases examined. Cox regression analysis showed no difference in the overall survival rates of miniscrews loaded with different appliances for sex (hazard ratio, 0.95; 95% confidence interval, 0.71-1.27; P = 0.73) after adjusting for appliance and age. This study shows that miniscrews placed in the paramedian anterior palate for supporting various orthodontic appliances have excellent survival. Copyright © 2013 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  16. Modelling the effects of U.S. ENERGY STARR appliance programs

    International Nuclear Information System (INIS)

    Feldman, Shel; Hoefgen, Lynn; Wilson-Wright, Lisa; Li, Angela

    2005-01-01

    Numerous U.S. utilities and market transformation organizations have invested heavily in the ENERGY STAR program, designed to increase market penetration of energy-efficient products (e.g., home appliances, lighting products, windows). Major activities involve stimulating production and promotion of qualifying models, as well as stocking, sales support and financial incentives to customers-all of which entail considerable investments of public funds. Several studies have shown that customer awareness of ENERGY STAR has increased across the country, particularly where energy-efficiency programs have been most active. Furthermore, studies in regions with aggressive programs have shown that the market penetration of qualifying products has increased rapidly. Until recently, however, policy makers have lacked reliable studies that compare changes in market penetration across regions with and without programs while factoring out effects of demographic and other background factors (e.g., education, income, and climate). Also lacking have been attempts to assess whether heavy promotion of the ENERGY STAR brand with some appliances (e.g., clothes washers) has affected the market penetration of less-promoted qualifying appliances. In this paper, the authors address these issues, using a database of the market penetration of four major home appliances at national retailers in each of the individual states over a multi-year period, based on multivariate statistical models. Results include both analyses of the overall trend of market penetration (1998-2002) for the appliances considered and the incremental effects of the 2003 program. The results lead to recommendations regarding the design of programs supporting ENERGY STAR compliant appliances and the key components of those programs

  17. FY 2000 Development of technologies for reducing power consumption during the stand-by period. Report on the research and development results of rationally reducing power consumption by home electric appliances; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden seihin no taikiji shohi denryoku no goriteki sakugen ni kansuru kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research and development project is implemented for development of the system which automatically switches off the power source for a standing-by appliance by analyzing life pattern in each home, in order to reduce consumed power during the stand-by period. The actual service conditions of appliances in each home are surveyed through the questionnaires and recording in the diary. The analysis results indicate that as high as 70% of those who are inquired take interest in energy saving, especially high among full-time housewives. The home electric appliances considered by many to wastefully consume power are functional-keeping types, e.g., (jar pots) and (toilet seats equipped with a washing function with warm water), and heating appliances, e.g., (hot carpets). The power consumption trends at each time in each home are measured and grasped by the aid of a tool with built-in personal computer, and the algorithm for predicting use of the appliances in each home is developed for each home, based on the analysis results. The prototype energy-saving adapter and centralized controller are developed, and subjected to various tests to develop the learning/controlling algorithms. The demonstration tests of the energy-saving adapter developed confirm that power consumption during the stand-by period can be reduced at least by 10%. (NEDO)

  18. File System Virtual Appliances

    Science.gov (United States)

    2010-05-01

    4 KB of data is read or written, data is copied back and forth using trampoline buffers — pages that are shared during proxy initialization — because...in 2008. CIO Magazine. 104 · File system virtual appliances [64] Megiddo, N. and Modha, D. S. 2003. ARC: A Self-Tuning, Low Over- head Replacement

  19. A Profile-Based Identification of Standby and Useless Electricity Consumption in Buildings

    OpenAIRE

    De Koster, Rien; Van Roy, Juan; Driesen, Johan

    2013-01-01

    Useless electricity consumption is the electricity consumption of an electric appliance or system that is not performing its primary function or that is performing its primary function without being useful. So, useless electricity consumption does not only consist of standby losses. To identify the useless electricity consumption in a building, a profile-based approach is developed. This approach is used to investigate the useless electricity consumption in five buildings of the University of...

  20. Economical regulation power through load shifting with smart energy appliances

    NARCIS (Netherlands)

    Vlot, M.C.; Knigge, J.D.; Slootweg, J.G.

    2013-01-01

    This paper considers the technical and economical feasibility of the introduction of automated demand response from domestic smart appliances in a European setting as a means to create a significant amount of regulating power. Simplified power-time flexibility models for appliances are introduced on

  1. Treatment of obstructive sleep apnea patients using oral appliances--our experiences.

    Science.gov (United States)

    Miljus, Dusan; Tihacek-Sojić, Ljiljana; Milić-Lemić, Aleksandra; Andjelković, Marko

    2014-07-01

    Obstructive sleep apnea (OSA) is one of the most prevalent sleep disorders. It is recognized as a serious risk factor for car and workplace accidents due to daytime sleepiness, and factor for coronary heart diseases and stroke. The aim of this study was to examine the effectiveness of oral appliances for mandibular advance in treating mild to moderate OSA. A total of 15 patients were included in this study, all diagnosed with mild or moderate OSA. Oral appliances were custom made for each patient in protrusive position at 50% of maximum mandibular advancement. The patients were given instructions not to sleep on their backs and avoid alcohol consumption during the study as these are the factors that can contribute to symptoms progression. Complete and partial treatment success was achieve in 14 of the patients. Apnea-hypopnea index values were significantly lower (p appliances has proven successful. Patients were comfortable using oral appliances and were ready to wear them for prolonged period of time. Use of oral appliances is very common in the world and should not be discarded. They are also very comfortable, practical and affordable comparing to continuous positive airway pressure (CPAP) apparatus, not to mention surgery. Use of oral appliances is safe and very well tolerated, and ought to be offered to patients with OSA.

  2. 46 CFR 133.40 - Evaluation, testing and approval of lifesaving appliances and arrangements.

    Science.gov (United States)

    2010-10-01

    ... appliances and arrangements. 133.40 Section 133.40 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY... lifesaving appliances and arrangements. (a) Each item of lifesaving equipment required by this part to be... OCMI for use on the OSV. (c) The Commandant (CG-521) may accept a novel lifesaving appliance or...

  3. 14 CFR 21.617 - Issue of letters of TSO design approval: import appliances.

    Science.gov (United States)

    2010-01-01

    ...: import appliances. 21.617 Section 21.617 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... Order Authorizations § 21.617 Issue of letters of TSO design approval: import appliances. (a) A letter of TSO design approval may be issued for an appliance that is manufactured in a foreign country with...

  4. Switch green : Energy Star appliance feebate

    International Nuclear Information System (INIS)

    2007-01-01

    Between 1990 and 2004, greenhouse gas (GHG) emissions from the residential sector have grown by 10 per cent, and are likely to continue growing unless a policy aimed at reducing emissions is introduced. The residential sector is a significant contributor to Canada's overall GHG emissions, and an important source for potential reductions. This report presented the results of a study that described and evaluated a new economic instrument aimed at reducing greenhouse gas (GHG) emissions and energy consumption in Canada from household appliances, such as air conditioners, furnaces and boilers. Results of a quantitative analysis to determine the effect of changing taxation of residential appliances to reflect energy consumption and greenhouse gas emissions were presented. In addition, the report presented the results of a qualitative evaluation of the policy, using the criteria established in the 2005 budget plan, a framework for evaluating environmental tax proposals. The report outlined the context for the tax proposal that was evaluated and provided a summary of trends in Canada's greenhouse gas emissions and energy consumption as well as a discussion of important trends in residential energy consumption. A review of policies already in place to address energy consumption from household appliances was also presented. 11 tabs., 6 figs

  5. Electrical and Biological Effects of Transmission Lines: A Review.

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jack M.

    1989-06-01

    This review describes the electrical properties of a-c and d-c transmission lines and the resulting effects on plants, animals, and people. Methods used by BPA to mitigate undesirable effects are also discussed. Although much of the information in this review pertains to high-voltage transmission lines, information on distribution lines and electrical appliances is included. The electrical properties discussed are electric and magnetic fields and corona: first for alternating-current (a-c) lines, then for direct current (d-c).

  6. Understanding usage patterns of electric kettle and energy saving potential

    International Nuclear Information System (INIS)

    Murray, D.M.; Liao, J.; Stankovic, L.; Stankovic, V.

    2016-01-01

    Highlights: • Time-of-use analysis to motivate kettle usage and consumption prediction. • Identification of households whose kettle usage and consumption is outside the norm. • Mathematical model to estimate water volume from consumed power measurements only. • Quantification of energy savings if a household uses its kettle more efficiently. • Kettle usage and demand prediction using an Adaptive Neuro Fuzzy Inference System. - Abstract: The availability of smart metering and smart appliances enables detecting and characterising appliance use in a household, quantifying energy savings through efficient appliance use and predicting appliance-specific demand from load measurements is possible. With growing electric kettle ownership and usage, lack of any efficiency labelling guidelines for the kettle, slow technological progress in improving kettle efficiency relative to other domestic appliances, and current consumer attitudes, urgent investigation into consumer kettle usage patterns is warranted. From an efficiency point of view, little can be done about the kettle, which is more efficient than other methods of heating water such as the stove top kettle. However, since a majority households use the kettle inefficiently by overfilling, in order to meet energy targets, it is imperative to quantify inefficient usage and predict demand. For the purposes of scalability, we propose tools that depend only on load measurement data for quantifying and visualising kettle usage and energy consumption, assessing energy wastage through overfilling via our proposed electric kettle model, and predicting kettle-specific demand, from which we can estimate potential energy savings in a household and across a housing stock. This is demonstrated using data from a longitudinal study across a sample of 14 UK households for a two-year period.

  7. Improvements in appliance holders

    International Nuclear Information System (INIS)

    Chapman, J.E.

    1977-01-01

    Reference is made to appliance holders for locating tools, instruments, etc. in operative relationship to workpieces and accessible through passageways of restricted transverse dimensions. The appliance holder described comprises an elongated external frame provided with transversely, outwardly expanding frictional gripping means in two longitudinally spaced sets and with a ring of spur teeth. An inner elongated frame is held within the external frame in two longitudinally spaced rotary bearings and carries a spur wheel which engages the ring of the spur teeth. A motor is arranged to rotate the spur wheel and hence the inner frame in relation to the external frame. A carriage is carried by the inner frame, longitudinally movable by a motor in relation thereto, and a further carriage is mounted on this first carriage. This second cariage is transversely movable in relation to the inner frame and is provided with a face plate for attachment of tools, instruments, etc. A motor is mounted on the first carriage for moving the second carriage. (U.K.)

  8. 76 FR 79057 - Appliance Labeling Rule

    Science.gov (United States)

    2011-12-21

    ... Part 305 Advertising, Energy conservation, Household appliances, Labeling, Reporting and recordkeeping... emitting diode (OLED) means a thin-film light- emitting device that typically consists of a series of...

  9. Class II malocclusion treatment using combined Twin Block and fixed orthodontic appliances – A case report

    Science.gov (United States)

    Al-Anezi, Saud A.

    2010-01-01

    The effect of the Twin Block functional orthodontic appliances is mostly dento-alveolar with small skeletal effect. There are certain clinical indications where functional appliances can be used successfully in class II malocclusion e.g. in a growing patient. The use of these appliances is greatly dependent on the patient’s compliance and they simplify the fixed appliance phase. In this case, a 13-year old adolescent was treated with Twin Block appliance followed by fixed appliance to detail the occlusion. The design and treatment effects were demonstrated in this case report. PMID:24151413

  10. Routines for interocclusal appliance therapy among general dental practitioners in a Swedish county.

    Science.gov (United States)

    Gnauck, Maja; Helkimo, Martti; Magnusson, Tomas

    2012-01-01

    The aims of this study were to investigate what kind of interocclusal appliances that were chosen among Swedish dentists when treating temporomandibular disorders (TMD), the clinical rationale for the treatment, the diagnoses that warranted the appliance treatment, the use of adjunct TMD treatments and prognostic considerations, and possible differences in these respects between children/adolescents and adults with TMD, and, finally, possible differences between private practitioners and general practitioners in the public dental service. During the 12-months-period April 2009-March 2010 all general dental practitioners in the county of Jönköping, Sweden, were asked to fill in a questionnaire when performing a TMD treatment with an interocclusal appliance. A total of 394 questionnaires were filled in and returned, 216 (55%) from dentists in public dental service and 178 (45%) from private practitioners. It was found that in 40% of the cases, no pre-treatment recording of the functional status in the masticatory system had been made. The commonest reasons for the treatment were bruxism, headache, and replacement of a previous appliance. Less than half of the appliances made were hard acrylic appliances. Some kind of adjunct therapy had been made in 22% of the cases treated in public dental service. The corresponding figure for those treated by private practitioners was 25%. Therapeutic jaw exercises was the commonest adjunct therapy followed by selective occlusal adjustment. In the vast majority of cases, the dentists judged the prognosis of the treatment to be good. It is concluded that a large number of appliances made to treat TMD were soft appliances, especially in public dental service. This reflects a possible overuse of soft appliances at the expense of hard acrylic appliances. Furthermore, in a large number of cases, the treatment was performed without any pre-treatment registrations, and adjunct therapies were rarely used. In all these respects,there is

  11. Assessment of Human Exposure to Magnetic Fields Produced by Domestic Appliances (invited paper)

    International Nuclear Information System (INIS)

    Preece, A.W.; Kaune, W.T.; Grainger, P.; Golding, J.

    1999-01-01

    A study of 50 homes and their appliances examined whether a detailed appliance-use questionnaire and survey would yield data comparable with direct personal monitoring. This was coupled with direct measurement of the appliances in use to determine the field at 50 cm and 1 m. The findings were that individual time-weighted average (TWA) exposures calculated from questionnaire and activity diaries in conjunction with the appliance magnetic field were unrelated to actual personal exposure measurement. It was concluded that questionnaires are of little or no value for TWA estimation. However, peak exposure and short-term temporal variability could be modelled in subjects spending at least 15 min per day within 1 m of an operating microwave cooker or conventional cooker. This method could be extended to other appliances. (author)

  12. Treatment with active orthodontic appliance in adult patient

    OpenAIRE

    Radeska, Ana; Radeski, Josif; Zlatanovska, Katerina; Papakoca, Kiro; Zarkova, Julija

    2012-01-01

    Aim: Showing the efficiency of orthodontic mobile appliance in treatment of adult patient Case summary: The patient A.K. Age 25 years whit forced progenia, bilateral hypodontia of the maxillary incisors and cross bite of 2 mm in front. The patient was treated with active orthodontic appliance whit bitten ridge and down labial arch. The treatment lasted 18 months after which periods is reached normal occlusion with normal overlap in front and closed diastema mediana. The hypodontia of the m...

  13. Home Appliances as Home Controllers: Concepts and Set-Top Box Implementation

    Directory of Open Access Journals (Sweden)

    Z. Jovanovic

    2010-11-01

    Full Text Available In this paper we present a novel softwarebased home control platform suitable as an extension to digital home appliances that are equipped with a CPU (settop boxes, home theatre systems, TV sets, gaming consoles, etc. By using an appliance they are already accustomed to, users become able to control lights, appliances and media playback in their homes. Intelligence and awareness are achieved with a support for execution of recipes – preprepared scripts that define timely actions and respond to triggers obtained from sensors. Software abstraction layer facilitates integration of any desired communication protocol. In our prototype, we supported Zigbee and DMX for light control, X10 for light/appliances control over power line, as well as Ethernet-based optical cameras as motion/presence sensors and UPnP/DLNA based equipment for distributed media playback.

  14. An investigation into the vector ellipticity of extremely low frequency magnetic fields from appliances in UK homes

    International Nuclear Information System (INIS)

    Ainsbury, Elizabeth A; Conein, Emma; Henshaw, Denis L

    2005-01-01

    Elliptically polarized magnetic fields induce higher currents in the body compared with their plane polarized counterparts. This investigation examines the degree of vector ellipticity of extremely low frequency magnetic fields (ELF-MFs) in the home, with regard to the adverse health effects reportedly associated with ELF-MFs, for instance childhood leukaemia. Tri-axial measurements of the magnitude and phase of the 0-3000 Hz magnetic fields, produced by 226 domestic mains-fed appliances of 32 different types, were carried out in 16 homes in Worcestershire in the summer of 2004. Magnetic field strengths were low, with average (RMS) values of 0.03 ± 0.02 μT across all residences. In contrast, background field ellipticities were high, on average 47 ± 11%. Microwave and electric ovens produced the highest ellipticities: mean respective values of 21 ± 21% and 21 ± 17% were observed 20 cm away from these appliances. There was a negative correlation between field strength and field polarization, which we attribute to the higher relative field contribution close to each individual (single-phase) appliance. The measurements demonstrate that domestic magnetic fields are extremely complex and cannot simply be characterized by traditional measurements such as time-weighted average or peak exposure levels. We conclude that ellipticity should become a relevant metric for future epidemiological studies of health and ELF-MF exposure

  15. Effects of mechanical properties of thermoplastic materials on the initial force of thermoplastic appliances.

    Science.gov (United States)

    Kohda, Naohisa; Iijima, Masahiro; Muguruma, Takeshi; Brantley, William A; Ahluwalia, Karamdeep S; Mizoguchi, Itaru

    2013-05-01

    To measure the forces delivered by thermoplastic appliances made from three materials and investigate effects of mechanical properties, material thickness, and amount of activation on orthodontic forces. Three thermoplastic materials, Duran (Scheu Dental), Erkodur (Erkodent Erich Kopp GmbH), and Hardcast (Scheu Dental), with two different thicknesses were selected. Values of elastic modulus and hardness were obtained from nanoindentation measurements at 28°C. A custom-fabricated system with a force sensor was employed to obtain measurements of in vitro force delivered by the thermoplastic appliances for 0.5-mm and 1.0-mm activation for bodily tooth movement. Experimental results were subjected to several statistical analyses. Hardcast had significantly lower elastic modulus and hardness than Duran and Erkodur, whose properties were not significantly different. Appliances fabricated from thicker material (0.75 mm or 0.8 mm) always produced significantly greater force than those fabricated from thinner material (0.4 mm or 0.5 mm). Appliances with 1.0-mm activation produced significantly lower force than those with 0.5-mm activation, except for 0.4-mm thick Hardcast appliances. A strong correlation was found between mechanical properties of the thermoplastic materials and force produced by the appliances. Orthodontic forces delivered by thermoplastic appliances depend on the material, thickness, and amount of activation. Mechanical properties of the polymers obtained by nanoindentation testing are predictive of force delivery by these appliances.

  16. Design and manufacturing of patient-specific orthodontic appliances by computer-aided engineering techniques.

    Science.gov (United States)

    Barone, Sandro; Neri, Paolo; Paoli, Alessandro; Razionale, Armando Viviano

    2018-01-01

    Orthodontic treatments are usually performed using fixed brackets or removable oral appliances, which are traditionally made from alginate impressions and wax registrations. Among removable devices, eruption guidance appliances are used for early orthodontic treatments in order to intercept and prevent malocclusion problems. Commercially available eruption guidance appliances, however, are symmetric devices produced using a few standard sizes. For this reason, they are not able to meet all the specific patient's needs since the actual dental anatomies present various geometries and asymmetric conditions. In this article, a computer-aided design-based methodology for the design and manufacturing of a patient-specific eruption guidance appliances is presented. The proposed approach is based on the digitalization of several steps of the overall process: from the digital reconstruction of patients' anatomies to the manufacturing of customized appliances. A finite element model has been developed to evaluate the temporomandibular joint disks stress level caused by using symmetric eruption guidance appliances with different teeth misalignment conditions. The developed model can then be used to guide the design of a patient-specific appliance with the aim at reducing the patient discomfort. At this purpose, two different customization levels are proposed in order to face both arches and single tooth misalignment issues. A low-cost manufacturing process, based on an additive manufacturing technique, is finally presented and discussed.

  17. Treatment effects of the Jasper Jumper and the Bionator associated with fixed appliances.

    Science.gov (United States)

    Neves, Leniana Santos; Janson, Guilherme; Cançado, Rodrigo Hermont; de Lima, Karina Jerônimo Rodrigues Santiago; Fernandes, Thaís Maria Freire; Henriques, José Fernando Castanha

    2014-01-01

    The aim of this study was to evaluate the effects of Class II malocclusion treatment with the Jasper Jumper and the Bionator, associated with fixed appliances. The sample comprised 77 young individuals divided into 3 groups: Group 1 consisted of 25 patients treated with the Jasper Jumper appliance associated with fixed appliances for a mean period of 2.15 years; group 2 had 30 patients, treated with the Bionator and fixed appliances, for a mean treatment time of 3.92 years; and the control group included 22 subjects followed for a mean period of 2.13 years. The initial and final lateral cephalograms of the patients were evaluated. Intergroup comparison at the initial stage and of the treatment changes were performed by analysis of variance. Their effects consisted in a restrictive effect on the maxilla, a slight increase in anterior face height, retrusion and extrusion of the maxillary incisors, labial tipping and protrusion of the mandibular incisors in both groups and intrusion with the Jasper Jumper appliance, maxillary molar distalization with the Jasper Jumper, extrusion and mesialization of the mandibular molars, both appliances provided significant improvement of the maxillomandibular relationship, overjet, overbite and molar relationship. The effects of both appliances in class II malocclusion treatment are similar; however, treatment with the Jasper Jumper was shorter than with the Bionator.

  18. Do soft drinks affect metal ions release from orthodontic appliances?

    Science.gov (United States)

    Mikulewicz, Marcin; Wołowiec, Paulina; Loster, Bartłomiej W; Chojnacka, Katarzyna

    2015-01-01

    The effect of orange juice and Coca Cola(®) on the release of metal ions from fixed orthodontic appliances. A continuous flow system designed for in vitro testing of orthodontic appliances was used. Orange juice/Coca Cola(®) was flowing through the system alternately with artificial saliva for 5.5 and 18.5h, respectively. The collected samples underwent a multielemental ICP-OES analysis in order to determine the metal ions release pattern in time. The total mass of ions released from the appliance into orange juice and Coca Cola(®) (respectively) during the experiment was calculated (μg): Ni (15.33; 37.75), Cr (3.604; 1.052), Fe (48.42; ≥ 156.1), Cu (57.87, 32.91), Mn (9.164; 41.16), Mo (9.999; 30.12), and Cd (0.5967; 2.173). It was found that orange juice did not intensify the release of metal ions from orthodontic appliances, whereas Coca Cola(®) caused increased release of Ni ions. Copyright © 2015 Elsevier GmbH. All rights reserved.

  19. Inactivation of Escherichia coli O157:H7 in moisture-enhanced nonintact beef by pan-broiling or roasting with various cooking appliances set at different temperatures.

    Science.gov (United States)

    Shen, Cangliang; Geornaras, Ifigenia; Belk, Keith E; Smith, Gary C; Sofos, John N

    2011-01-01

    This study evaluated inactivation of Escherichia coli O157:H7 in moisture-enhanced restructured nonintact beef cooked to 65 °C using different cooking appliances set at different temperatures. Batches (2 kg) of coarse-ground beef (approximately 5% fat) were mixed with an 8-strain composite (100 mL) of rifampicin-resistant E. coli O157:H7 (6.4 ± 0.1 log CFU/g) and a solution (100 mL) of sodium chloride plus sodium tripolyphosphate to yield concentrations (wt/wt) of 0.5% and 0.25%, respectively, in the final product. Beef portions of 2.54 cm thickness (15 cm dia) were prepared and were vacuum-packaged and frozen (-20 °C, 42 h). Partially thawed (-2.5 ± 1.0 °C) portions were pan-broiled (Presto electric skillet and Sanyo grill) or roasted (Oster toaster oven and Magic Chef kitchen oven) to 65 °C. The appliances were set at, and preheated before cooking to 149 or 204 °C (electric skillet), 149 or 218 °C (grill), 149 or 232 °C (toaster oven), and 149, 204, or 260 °C (kitchen oven). Temperatures of appliances and beef samples were monitored with thermocouples, and meat samples were analyzed for surviving microbial populations. In general, the higher the appliance temperature setting, the shorter the time needed to reach 65 °C, and the higher the edge and surface temperatures of the meat samples. Temperatures of 204 to 260 °C, regardless of appliance, resulted in greater (P kitchen oven set at 260 °C. The results should be useful to the food service industry for selection of effective nonintact beef cooking protocols, and for use in risk assessments for nonintact meat products. Practical Application: Results of this study should be useful for developing cooking recommendations to enhance the safety of nonintact beef products, and for use in risk assessments of such products.

  20. What to Do If Your Appliances Are Wet After a Disaster

    Centers for Disease Control (CDC) Podcasts

    2006-08-10

    If your home was flooded, look for signs that your appliances have gotten wet. Throw away wet or flooded appliances to protect from shock and fire.  Created: 8/10/2006 by Emergency Communications System.   Date Released: 7/30/2008.

  1. Association of tooth brushing behavior with oral hygiene index among students using fixed appliance

    Science.gov (United States)

    Ria, N.; Eyanoer, P.

    2018-03-01

    Uses of fixed appliance have become popular recently. The purpose of its use is to correct malposition of teeth in order to normalize the masticatory function and to eliminate the accumulation of food remain between the teeth. These will prevent the formation of caries and any periodontal tissue disease. Fixed appliance patients must routinely maintain their oral hygiene. This study was an analytical survey with cross-sectional design to know the relationship between behavior in tooth brushing of students using thefixed appliance and oral hygiene in Poltekkes Kemenkes Medan. The average of Oral Hygiene Index – Simplified (OHI-S) value of students using fixed appliance (2.68) was still above national target which is ≤2, and there was a relationship between behavior in tooth brushing of students using the fixed appliance and oral hygiene (phygiene and to prevent caries formation and periodontal disease patients using fixed appliances should maintain their dental health.

  2. Design and explanation of organizational excellence model in home appliances industry

    Directory of Open Access Journals (Sweden)

    Seyed Abbas Kazemi

    2012-01-01

    Full Text Available Home appliances are considered as one of low margin and competitive industry in the world. This industry often needs significant amount of investment and resources and it often faces with some challenges during economic crises. In this paper, we present a framework for organizational excellence to detect any possible problems in home appliances industry. The proposed framework of this paper is used for a real-world case study of Iranian home appliances. The results of our survey indicate that there are four major dimensions involved with this industry including facilities, knowledge and skills, environment and vision. There are three criteria associated with facilities with 30 indexes, 14 criteria associated with knowledge and skills with 144 indexes, three criteria involved with environment with 33 indexes and five criteria linked with vision with 53 indexes. Therefore, home appliances in our case study needs 4 dimensions for achieving the organizational excellence.

  3. 49 CFR 176.54 - Repairs involving welding, burning, and power-actuated tools and appliances.

    Science.gov (United States)

    2010-10-01

    ...-actuated tools and appliances. 176.54 Section 176.54 Transportation Other Regulations Relating to..., burning, and power-actuated tools and appliances. (a) Except as provided in paragraph (b) of this section, repairs or work involving welding or burning, or the use of power-actuated tools or appliances which may...

  4. Quantifying the Flexibility of Residential Electricity Demand in 2050: a Bottom-Up Approach

    OpenAIRE

    van Stiphout, Arne; Engels, Jonas; Guldentops, Dries; Deconinck, Geert

    2015-01-01

    This work presents a new method to quantify the flexibility of automatic demand response applied to residential electricity demand using price elasticities. A stochastic bottom-up model of flexible electricity demand in 2050 is presented. Three types of flexible devices are implemented: electrical heating, electric vehicles and wet appliances. Each house schedules its flexible demand w.r.t. a varying price signal, in order to minimize electricity cost. Own- and cross-price elasticities are ob...

  5. Fixed-functional appliance treatment combined with growth hormone therapy.

    Science.gov (United States)

    Jung, Min-Ho

    2017-09-01

    The purpose of this study was to illustrate the effects of growth hormone (GH) therapy and fixed functional appliance treatment in a 13-year-old Class II malocclusion patient without GH deficiency. GH has been shown to effectively increase endochondral growth and induce a more prognathic skeletal pattern. Although a major concern in Class II retrognathic patients is chin deficiency, long-term studies have shown that the mandibular growth enhancement effects of functional appliances are clinically insignificant. This case report demonstrates that the mandible grew significantly during fixed functional appliance treatment combined with GH therapy, with stable results during 2 years 11 months of retention. More studies are needed to evaluate GH therapy as a supplement in Class II treatment. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  6. A comparison of pain experienced by patients treated with labial and lingual orthodontic appliances.

    Science.gov (United States)

    Wu, Abby K Y; McGrath, Colman; Wong, Ricky W K; Wiechmann, D; Rabie, A Bakr M

    2010-08-01

    The aim of this prospective longitudinal study was to compare pain experiences among Chinese adult patients treated with labial and lingual orthodontic appliances. Sixty patients, 30 with labial appliances (18 females and 12 males, mean age 20.33 years, SD +/- 4.205) and 30 with lingual appliances (22 females and 8 males, mean age 21.63 years, SD +/- 2.236), rated their overall pain experience on a 100 mm visual analogue scale (VAS) at three time points: 1 week (T(1)), 1 month (T(2)), and 3 months (T(3)) after bracket placement. In addition, on a separate 100 mm VAS, they rated their pain experience at the locations of the tongue, lips, cheeks, gums, face, and jaw at T(1), T(2), and T(3). Changes in pain VAS were conducted using Friedman analysis of variance, area under the curve (AUC) analysis and the data were compared using a t-test. There was no significant difference in global ratings of pain among those treated with labial or lingual appliances (P > 0.05). Among both groups, global ratings of pain decreased over the study period (P appliances reported higher ratings of tongue pain (P appliances reported higher ratings of lip (P appliances rate similarly the level of overall pain they experience during treatment. Ratings of overall pain experienced decreased for both treatment groups with time. However, ratings of pain differed at various sites with respect to the type of orthodontic appliance. These findings have implications in informing patients' treatment decision-making processes regarding labial and lingual appliances and in the management of discomfort associated with different treatment modalities.

  7. Effects of socioeconomic factors on household appliance, lighting, and space cooling electricity consumption

    Energy Technology Data Exchange (ETDEWEB)

    Aydinalp, M. [Itron Inc., Boston, MA (United States); Ismet Ugursal, V.; Fung, A.S. [Dalhousie University, Halifax (Canada). Dept. of Mechanical Engineering

    2003-07-01

    Two methods are currently used to model residential energy consumption at the national or regional level: the engineering method and the conditional demand analysis (CDA) method. One of the major difficulties associated with the use of engineering models is the inclusion of consumer behaviour and socioeconomic factors that have significant effects on the residential energy consumption. The CDA method can handle socioeconomic factors if they are included in the model formulation. However, the multicollinearity problem and the need for a very large amount of data make the use of CDA models very difficult. It is shown in this paper that the neural network (NN) method can be used to model the residential energy consumption with the inclusion of socioeconomic factors. The appliances, lighting, and cooling component of the NN based energy consumption model developed for the Canadian residential sector is presented here and the effects of some socioeconomic factors on the residential energy consumption are examined using the model. (author)

  8. Electrical Grid Stability Enhancement using Smart Home Frequency-response Grid -Friendly Appliance System

    Directory of Open Access Journals (Sweden)

    Muawiya A. Kaigama

    2016-03-01

    Full Text Available Load shedding is a powerful scheme used for corrective and preventive measures; corrective to restore system’s stability and preventive to avoid catastrophic failure. However, the affected end users are deprived of power supply absolutely with no choice. This paper presents the design, development, feasibility and merits of Frequency-response Grid -Friendly Appliance System (FRGFAS in a smart home. FRGFAS is a decentralized Adaptive Load Shaving(ALS device that supports grid’s system stability by sensing grid’s frequency deterioration level and turns ON/OFF loads accordingly. The FRGFAS permits end users to carry out load shaving at their scale of preference in smart homes via flexible demand responses and automates outdoor lighting to optimum operational hours. FRGFAS obviate load shedding by shaving loads whenever the system is in distress and reset loads supply to the normal state when it stabilizes, this Consequently increases the end user comfort zone and averts a blackout.

  9. 16 CFR Appendix D2 to Part 305 - Water Heaters-Electric

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Water Heaters-Electric D2 Appendix D2 to... PRODUCTS REQUIRED UNDER THE ENERGY POLICY AND CONSERVATION ACT (âAPPLIANCE LABELING RULEâ) Pt. 305, App. D2 Appendix D2 to Part 305—Water Heaters—Electric Range Information CAPACITY FIRST HOUR RATING Range of...

  10. A modified palatal crib appliance for children with predetermined thumb-sucking habit - Case report

    International Nuclear Information System (INIS)

    AlEmran, Sulaiman

    2008-01-01

    The aim of this case report was to introduce a modified design of palatal crib habit breaking appliance that can be used for children with predetermined thumb-sucking habit. The appliance is made of two bands on the upper first permanent molars and an extended metal framework to cover the anterior of the palatal roof. The appliance was applied for 4 months on an 8-year-old boy who persistently continued the habit of thumb-sucking. The appliance proved to be very effective for arresting thumb-sucking habit. (author)

  11. Assessment of end-use electricity consumption and peak demand by Townsville's housing stock

    International Nuclear Information System (INIS)

    Ren, Zhengen; Paevere, Phillip; Grozev, George; Egan, Stephen; Anticev, Julia

    2013-01-01

    We have developed a comprehensive model to estimate annual end-use electricity consumption and peak demand of housing stock, considering occupants' use of air conditioning systems and major appliances. The model was applied to analyse private dwellings in Townsville, Australia's largest tropical city. For the financial year (FY) 2010–11 the predicted results agreed with the actual electricity consumption with an error less than 10% for cooling thermostat settings at the standard setting temperature of 26.5 °C and at 1.0 °C higher than the standard setting. The greatest difference in monthly electricity consumption in the summer season between the model and the actual data decreased from 21% to 2% when the thermostat setting was changed from 26.5 °C to 27.5 °C. Our findings also showed that installation of solar panels in Townville houses could reduce electricity demand from the grid and would have a minor impact on the yearly peak demand. A key new feature of the model is that it can be used to predict probability distribution of energy demand considering (a) that appliances may be used randomly and (b) the way people use thermostats. The peak demand for the FY estimated from the probability distribution tracked the actual peak demand at 97% confidence level. - Highlights: • We developed a model to estimate housing stock energy consumption and peak demand. • Appliances used randomly and thermostat settings for space cooling were considered. • On-site installation of solar panels was also considered. • Its' results agree well with the actual electricity consumption and peak demand. • It shows the model could provide the probability distribution of electricity demand

  12. Quebec residential electricity demand: a microeconometric approach

    International Nuclear Information System (INIS)

    Bernard, J.T.; Bolduc, D.; Belanger, D.

    1996-01-01

    An economic analysis of Quebec residential electricity demand was studied by micro-simulation models. These structural models describe all components which lead to decisions upon durable holdings and electric appliance usage. The demand for space and water heating systems was evaluated. Recent price change in favour of energy sources other than electricity were taken into account. Price and income elasticity ratios were found to be low, as expected when estimating short term use. The role played by socio-economic variables on the choice of space-water heating systems and electricity use was also examined. Recent conversions have indicated a trend toward preference by households in favour of natural gas or oil over electricity. 18 refs., 5 tabs., 1 fig

  13. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H [VTT Energy, Jyvaeskylae (Finland)

    1997-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  14. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1996-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  15. CE-mark for gas appliances: A laugh or a tear?

    International Nuclear Information System (INIS)

    Timmers, H.

    1993-01-01

    The title CE-mark is a quality mark for products, assigned by the European Community (EC). One and a half year ago the EC Gas Appliances Directive (GAD) came into force. According to the program 'Europe 1992' the European internal market should have been established by now. In this article the state of the art for gas appliances is given. Attention is paid to the systematics of European verification, the GAD contents, the consequences of a number of other Directives (for low-voltage materials, for electromagnetic compatibility, for efficiencies of central heating boilers, for machines, and for building products), which also affect the use of gas appliances, GASTEC's role as Notified Body, and experiences gained from European certification up to now. 6 ills., 3 tabs

  16. Smart Security System For Home Appliances Control Based On Internet Of Things

    Directory of Open Access Journals (Sweden)

    Su Zin Zin Win

    2015-08-01

    Full Text Available Technology is always evolves. Home security is essential for occupants convenience and protection. Security systems are being preferred over manual system. With the rapid increase in the number of users of internet over the past decade has made Internet a part and parcel of life and IoTs is the latest and emerging internet technology. Home Appliances Control of Smart Security System using IoTs uses computers or mobile devices to control basic home functions and features through internet from anywhere around the world. This security system differs from other system by allowing the user to operate the system from anywhere around the world through internet connection. With the implementation of Arduino Mega microcontroller as an Embedded device security system design was constructed with many sensors and web server database. The Arduino Ethernet shield is used to eliminate the use of a personal computer PC. The motion sensing circuit temperature and humidity sensing circuit smoke or gas sensing circuit door lock sensing circuit light onoff circuit were designed to be connected with Arduino Mega microcontroller and Ethernet shield. This system can monitor the temperature and humidity values and the state of some sensors for intruder detection. It can also control the electric appliances like lights and door at home. Real time result was displayed on web server page via the internet.

  17. Comparative evaluation of sagittal anchorage loss in lingual and labial appliances during space closure: A pilot study

    Directory of Open Access Journals (Sweden)

    Shivanand Venkatesh

    2015-01-01

    Full Text Available Aim: The purpose of this investigation was to assess and compare the anchorage loss between labial and lingual appliance systems during space closure. Materials and Methods: Twenty subjects were part of the study among which 10 subjects (mean age 21 ± 3.6 years were treated using lingual appliance system (0.018" slot-STb™ and 10 subjects (mean age 19 ± 6.1 years were treated using labial preadjusted edgewise appliance system (0.018" slot-MBT™ . First premolar extractions were performed to enable retraction of anterior teeth. Lateral cephalometric radiographs were taken at two intervals, before starting space closure and after space closure that were connoted as T0 and T1 and were analyzed using the method described by Pancherz to measure anchorage loss. Intraclass correlation coefficient (ICC was used to evaluate intraexaminer reliability of the measurements. Student′s t-test was performed to verify any statistical significant correlation between the labial and lingual appliance systems. Statistical differences were determined at the 95% confidence level (P < 0.05. Results: The results showed that all ICC for lingual and labial group were ≥0.90 showing good repeatability of the measurements. Mean anchorage loss of 1.238 ± 0.17 mm in lingual appliance system and an anchorage loss of 2.06 ± 0.39 mm occurred with the labial appliance system. On the comparison between the two appliance systems, lingual appliance demonstrated a significantly lesser anchorage loss than did the labial appliance. Interpretation and Conclusion: This prospective study concludes with the fact that lingual appliance provided better anchorage control than labial appliance during space closure. Use of lingual appliance could be considered in critical anchorage cases when compared with labial appliance.

  18. Assessment of Literature Related to Combustion Appliance Venting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Rapp, V. H.; Less, B. D.; Singer, B. C.; Stratton, J. C.; Wray, C. P.

    2015-02-01

    In many residential building retrofit programs, air tightening to increase energy efficiency is often constrained by safety concerns with naturally vented combustion appliances. Tighter residential buildings more readily depressurize when exhaust equipment is operated, making combustion appliances more prone to backdraft or spill combustion exhaust into the living space. Several measures, such as installation guidelines, vent sizing codes, and combustion safety diagnostics, are in place with the intent to prevent backdrafting and combustion spillage, but the diagnostics conflict and the risk mitigation objective is inconsistent. This literature review summarizes the metrics and diagnostics used to assess combustion safety, documents their technical basis, and investigates their risk mitigations. It compiles information from the following: codes for combustion appliance venting and installation; standards and guidelines for combustion safety diagnostics; research evaluating combustion safety diagnostics; research investigating wind effects on building depressurization and venting; and software for simulating vent system performance.

  19. 46 CFR 78.47-45 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to...-45 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with subchapter W...

  20. DNA damage in oral mucosa cells of patients with fixed orthodontic appliances.

    Directory of Open Access Journals (Sweden)

    Farzin Heravi

    2013-12-01

    Full Text Available The release of toxic metal ions from orthodontic alloys has induced concerns regarding the biocompatibility of fixed appliances. This study investigated the genotoxic effect of metal appliances in a sample of patients undergoing fixed orthodontic treatment.The study included twenty-five healthy individuals requiring orthodontic therapy in both jaws. The patients were treated by stainless steel orthodontic brackets and nickel-titanium or stainless steel arch wires. The oral mucosa cells were gathered just before the appliance placement and 9 months later. The cells were centrifuged, fixed and dropped onto slides. After staining, the micronucleus (MN assay was used to determine genome alteration. The data were analyzed by paired sample t-test.The mean micronuclei frequency in the buccal mucosa was 10.6 ± 5.7 per 1000 cells before the appliance placement and 9.2 ± 6.37 per 1000 cells 9 months later. No significant difference was found in the MN count before and 9 months after therapy (p=0.336.Under the conditions used in this study, application of fixed orthodontic appliances did not expose healthy individuals to increased risk of DNA damage in oral mucosa cells.

  1. 46 CFR 196.37-37 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., etc. § 196.37-37 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

  2. 46 CFR 97.37-42 - Markings for lifesaving appliances, instructions to passengers, and stowage locations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Markings for lifesaving appliances, instructions to..., Etc. § 97.37-42 Markings for lifesaving appliances, instructions to passengers, and stowage locations. Lifesaving appliances, instructions to passengers, and stowage locations must be marked in accordance with...

  3. Remote repair appliance

    International Nuclear Information System (INIS)

    Heumann, F.K.; Wilkinson, J.C.; Wooding, D.R.

    1997-01-01

    A remote appliance for supporting a tool for performing work at a work site on a substantially circular bore of a work piece and for providing video signals of the work site to a remote monitor comprises: a base plate having an inner face and an outer face; a plurality of rollers, wherein each roller is rotatably and adjustably attached to the inner face of the base plate and positioned to roll against the bore of the work piece when the base plate is positioned against the mouth of the bore such that the appliance may be rotated about the bore in a plane substantially parallel to the base plate; a tool holding means for supporting the tool, the tool holding means being adjustably attached to the outer face of the base plate such that the working end of the tool is positioned on the inner face side of the base plate; a camera for providing video signals of the work site to the remote monitor; and a camera holding means for supporting the camera on the inner face side of the base plate, the camera holding means being adjustably attached to the outer face of the base plate. In a preferred embodiment, roller guards are provided to protect the rollers from debris and a bore guard is provided to protect the bore from wear by the rollers and damage from debris. 5 figs

  4. Energy Savings Potential and Research, Development, & Demonstration Opportunities for Commercial Building Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zogg, Robert [Navigant Consulting, Inc., Burlington, MA (United States); Goetzler, William [Navigant Consulting, Inc., Burlington, MA (United States); Ahlfeldt, Christopher [Navigant Consulting, Inc., Burlington, MA (United States); Hiraiwa, Hirokazu [Navigant Consulting, Inc., Burlington, MA (United States); Sathe, Amul [Navigant Consulting, Inc., Burlington, MA (United States); Sutherland, Timothy [Navigant Consulting, Inc., Burlington, MA (United States)

    2009-12-01

    This study characterizes and assesses the appliances used in commercial buildings. The primary objectives of this study were to document the energy consumed by commercial appliances and identify research, development and demonstration (RD&D) opportunities for efficiency improvements, excluding product categories such as HVAC, building lighting, refrigeration equipment, and distributed generation systems. The study included equipment descriptions, characteristics of the equipment’s market, national energy consumption, estimates of technical potential for energy-saving technologies, and recommendations for U.S. Department of Energy programs that can promote energy savings in commercial appliances.

  5. Measured results and assessment of personal protection appliances against ionizing radiation

    International Nuclear Information System (INIS)

    Ge Lijuan; Lin Zhikai; Cao Jisheng; Zhu Pei; Tang Haiying; Liu Baiqun

    2011-01-01

    Objective: To monitor the protective qualities of personal protective appliances and to ensure the health and safety of radiological working personnel. Methods: The lead-equivalent thickness of personal protective appliances and materials was measured by means of standard lead slices. The lead equivalent thickness represents in terms of mm Pb. Results: 77 pieces of products and samples were measured altogether. The results indicate that the specific lead equivalents of lead-rubber plates were between 0.20-0.39 mm Pb/mm for 37 pieces of lead-rubber plates and the values of 6 pieces of samples were less than 0.25 mm Pb/mm, which did not accord with the requirement of the relational standard. 27 pieces of personal protection appliances were measured altogether. They were 12 pieces of protective clothes, 4 pieces of protective headgears, 5 pieces of protective neckpieces, 4 pieces of protective gloves and 2 pieces of protective masks. 13 pairs of lead-glass spectacles among them were measured altogether. The measured results for personal protective appliances and lead-glass spectacles showed that actually measured lead-equivalent were higher than the nominal lead-equivalent. Conclusions: The protective qualities are reliable for personal protection materials and appliances to be made in home and imported abroad. But the protective qualities of interventional protection gloves should be improved and made them better. (authors)

  6. Controlled, Rapid Uprighting of Molars: A surprisingly Simple Solution The Pivot Arm Appliance.

    Science.gov (United States)

    Warise, Timothy R; Galella, Steve A

    2015-01-01

    In orthodontic cases where the regional anatomy provides limited room for eruption, there is etiologically a higher occurrence of tipped/impacted second molars. Although second molar extraction with third molar replacement is a useful option, the "Pivot Arm Appliance" encourages the uprighting of the second molar as a preferred treatment. The most unique and important attribute of the "Pivot Arm Appliance" is the rotating tube. In cases of access limitation, the disto-occlusal surface of the molar presents as one area that is accessible. Other features of the "Pivot Arm Appliance" include: The position of the rotator tube delivers optimal rotational force through the pivoting action of the tube/arm complex. The "Pivot Arm Appliance" takes advantage of the efficiency and simplicity of a Class I lever system. The anatomical fulcrum being the dense cortical bone located anterior to the ascending ramus. The vertical spring system is compact, reliable and delivers gentle controlled force in rotational direction. The lingual location of the "Pivot Arm Appliance" does not hinder the function of the tongue, impinge on the soft tissue or interfere with normal masticatory function. The ease of placement of the rotator tube and subsequent insertion of the spring. It is well to note the uprighting appliance provides a very useful and practical approach to the unique problem of severely tipped second molars with limited buccal access. The "Pivot Arm Appliance" does not function only in these situations but can be used in all cases of second molar uprighting of a moderate to severe nature.

  7. Management of anterior dental crossbite with removable appliances

    Directory of Open Access Journals (Sweden)

    Ayca Tuba Ulusoy

    2013-01-01

    Full Text Available This case report describes the treatment of an 8-year-old girl with anterior dental crossbite using a series of removable appliances to bring the teeth into a normal position. Clinical presentation and intervention: A removable acrylic appliance with a bite plate incorporating a screw was used to correct the anterior dental crossbite and align the incisors. The subsequent eruption of the maxillary left lateral incisor on the palatinal side was treated with a second acrylic plate incorporating a labiolingual spring. After an 8-month period, the anterior crossbite involving multiple incisors was corrected.

  8. An investigation into the vector ellipticity of extremely low frequency magnetic fields from appliances in UK homes

    Science.gov (United States)

    Ainsbury, Elizabeth A.; Conein, Emma; Henshaw, Denis L.

    2005-07-01

    Elliptically polarized magnetic fields induce higher currents in the body compared with their plane polarized counterparts. This investigation examines the degree of vector ellipticity of extremely low frequency magnetic fields (ELF-MFs) in the home, with regard to the adverse health effects reportedly associated with ELF-MFs, for instance childhood leukaemia. Tri-axial measurements of the magnitude and phase of the 0-3000 Hz magnetic fields, produced by 226 domestic mains-fed appliances of 32 different types, were carried out in 16 homes in Worcestershire in the summer of 2004. Magnetic field strengths were low, with average (RMS) values of 0.03 ± 0.02 µT across all residences. In contrast, background field ellipticities were high, on average 47 ± 11%. Microwave and electric ovens produced the highest ellipticities: mean respective values of 21 ± 21% and 21 ± 17% were observed 20 cm away from these appliances. There was a negative correlation between field strength and field polarization, which we attribute to the higher relative field contribution close to each individual (single-phase) appliance. The measurements demonstrate that domestic magnetic fields are extremely complex and cannot simply be characterized by traditional measurements such as time-weighted average or peak exposure levels. We conclude that ellipticity should become a relevant metric for future epidemiological studies of health and ELF-MF exposure. This work is supported by the charity CHILDREN with LEUKAEMIA, registered charity number 298405.

  9. The Impact of Minimum Energy Performance Standards (MEPS) Regulation on Electricity Saving in Malaysia

    Science.gov (United States)

    Fatihah Salleh, Siti; Eqwan Roslan, Mohd; Isa, Aishah Mohd; Faizal Basri Nair, Mohd; Syafiqah Salleh, Siti

    2018-03-01

    One of Malaysia’s key strategies to promote efficient energy use in the country is to implement the minimum energy performance standards (MEPS) through the Electricity Regulations (Amendment) 2013. Five selected electrical appliances (refrigerator, air conditioner, television, domestic fans and lamp fittings) must comply with MEPS requirement in order to be sold in Malaysian market. Manufacturers, importers or distributors are issued Certificate of Approval (COA) if products are MEPS-compliant. In 2015, 1,215 COAs were issued but the number of MEPS products in the market is unknown. This work collects sales data from major manufacturers to estimate the annual sales of MEPS appliances and the cumulative electricity consumption and electricity saving. It was found that most products sold have 3-star rating and above. By year 2015, total cumulative electricity savings gained from MEPS implementation is 3,645 GWh, with air conditioner being the highest contributor (30%). In the future, it is recommended that more MEPS products and related incentives be introduced to further improve efficiency of energy use in Malaysia.

  10. Toward semantic interoperability of energy using and producing appliances in residential environments

    NARCIS (Netherlands)

    Hartog, F.T.H. den; Daniele, L.M.; Roes, J.B.M.

    2015-01-01

    About two thirds of the energy consumed in buildings originates household appliances. Nowadays, appliances are often intelligent and networked devices that form complete energy consuming, producing, and managing systems. Reducing energy is therefore a matter of managing and optimizing the energy

  11. Home Appliance Load Scheduling with SEMIAH

    DEFF Research Database (Denmark)

    Jacobsen, Rune Hylsberg; Ghasem Azar, Armin; Zhang, Qi

    2015-01-01

    The European research project SEMIAH aims at designing a scalable infrastructure for residential demand response. This paper presents the progress towards a centralized load scheduling algorithm for controlling home appliances taking power grid constraints and satisfaction of consumers into account....

  12. Orchestrating utility supply and demand in real-time via the Internet, home networks, and smart appliances

    Energy Technology Data Exchange (ETDEWEB)

    Cruickshank, R.F. III [Power Networks, Big Indian, NY (United States)

    2008-07-01

    This paper presented a model to illustrate the efficient coordination between the supply-side and demand-side of household electricity use and the magnitude of demand that can be managed using real-time pricing. In real-time supply and demand side management, a variable price for service is sent via Internet from the supply-side to the demand-side. The 3 benefits to this type of demand-side management are that traditional fossil-fuelled electrical capacity can operate less of the time and more efficiently; renewable electrical capacity such as wind and solar power can be put to use more efficiently when it becomes available; and additional means are available to protect the transmission and distribution infrastructure of the utility. A critical requirement is that pricing should change frequently throughout the day so that budget conscious consumers do not have to wait too long for favourable pricing to use their appliances. 12 refs., 9 figs.

  13. The economics of electricity markets

    CERN Document Server

    Biggar, Darryl R

    2014-01-01

    With the transition to liberalized electricity markets in many countries, the shift to more environmentally sustainable forms of power generation and increasing penetration of electric vehicles and smart appliances, a fundamental understanding of the economic principles underpinning the electricity industry is vital. Using clarity and precision, the authors successfully explain economic theory of all liberalized electricity market types from a cross-disciplinary engineering and policy perspective. No prior engineering knowledge or economics expertise is assumed in introducing key ideas such as nodal pricing, optimal dispatch and efficient pricing or in extending those models to areas including investment, risk management and the handling of contingencies. Key features: Comprehensively covers the principles of all liberalized electricity market types, including the US, Europe, New Zealand and Australia. Provides up to date coverage of research and policy iss es, including design of financial transmission rig...

  14. Changes in the oral environment after placement of lingual and labial orthodontic appliances.

    Science.gov (United States)

    Lombardo, Luca; Ortan, Yildiz Öztürk; Gorgun, Özge; Panza, Chiara; Scuzzo, Giuseppe; Siciliani, Giuseppe

    2013-09-11

    This study compared the oral hygiene and caries risk of patients treated with labial and lingual orthodontic appliances throughout a prospective evaluation of the status of the oral environment before and after bracket placement. A total of 20 orthodontic patients aged 19 to 23 years were included in the study and were divided into two groups: 10 patients wore Roth labial appliance (American Orthodontics, Sheboygan, WI, USA) and 10 patients wore STb lingual appliance (Ormco Corporation, Glendora, CA, USA). Plaque index (PI), gingival bleeding index (GBI), salivary flow rate, saliva buffer capacity, salivary pH, and Streptococcus mutans and Lactobacillus counts in saliva were determined at three time points: before orthodontic appliance placement (T0), 4 weeks after bonding (T1), and 8 weeks after bonding (T2). After appliance placement, all patients were periodically educated to the oral hygiene procedures. Wilcoxon rank and Mann-Whitney U tests were used to determine intragroup and intergroup differences as regards qualitative data. To compare quantitative data between the groups, chi-square and Fisher's exact tests were undertaken, while intragroup differences were tested with McNemar test. The level of statistical significance was set at pappliance. The GBI value increased significantly between T0 and T1 but decreased significantly between T1 and T2 (pappliance. S. mutans counts increased significantly between T0 and T2 in the saliva samples of patients treated with lingual appliance. No statistically significant differences were found between S. mutans and Lactobacillus counts at the three terms of saliva collection in patients treated with labial appliance. No statistically significant differences were found between the two groups at the three time points as regards the salivary flow rate and saliva buffer capacity. Lingual and labial orthodontic appliances showed a different potential in modifying the investigated clinical parameters: patients wearing STb

  15. Assessing consumer benefits of selected gas appliance technology center tasks. Topical report, April-December 1992

    International Nuclear Information System (INIS)

    Smith, T.R.; Bournakis, A.D.; Worek, W.M.; Kalensky, D.C.; Dombrowski, L.P.

    1992-12-01

    The Gas Appliance Technology Center (GATC) was created in 1983 to assist the gas industry in bringing about a new generation of reasonably priced, advanced gas appliances. The objective of the report is to evaluate consumer benefits of sixteen selected GATC tasks for the time period between 1983 and 1990. Tasks were selected for review based upon their degree of industry impact and how well they represented activities in the four targeted research areas of Space Conditioning, Commercial Appliances, Residential Appliances, and Codes and Standards

  16. Realization of Intelligent Household Appliance Wireless Monitoring Network Based on LEACH Protocol

    Directory of Open Access Journals (Sweden)

    Weilong ZHOU

    2014-06-01

    Full Text Available The intelligent household appliance wireless monitoring network can real-time monitor the apparent power and power factor of various household appliances in different indoor regions, and can realize the real-time monitoring on the household appliance working status and performance. The household appliance wireless monitoring network based on LEACH protocol is designed in the paper. Firstly, the basic idea of LEACH routing algorithm is proposed. Aiming at the node-distribution feature of intelligent home, the selection of cluster head in the routing algorithm and the data transmission method at the stable communication phase is modified. Moreover, the hardware circuit of power acquisition and power factor measurement is designed. The realization of wireless monitoring network based on CC2530 is described, each module and the whole system were conducted the on-line debugging. Finally, the system is proved to meet the practical requirement through the networking test.

  17. A new modified tandem appliance for management of developing Class III malocclusion

    Directory of Open Access Journals (Sweden)

    Ram Sukh

    2013-01-01

    Full Text Available Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior cross bite and retrognathic maxilla at the mixed dentition stage. Anterior cross bite was corrected in 3 months and the positive overjet of 4 mm after continued use of the appliance for 1 year. There was a significant improvement in profile of the patient. The use of this appliance in this type of malocclusion enabled the correction of malocclusion in a few months and encouraging favorable skeletal growth in the future.

  18. A new modified tandem appliance for management of developing Class III malocclusion.

    Science.gov (United States)

    Sukh, Ram; Singh, Gyan P; Tandon, Pradeep

    2013-10-01

    Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior cross bite and retrognathic maxilla at the mixed dentition stage. Anterior cross bite was corrected in 3 months and the positive overjet of 4 mm after continued use of the appliance for 1 year. There was a significant improvement in profile of the patient. The use of this appliance in this type of malocclusion enabled the correction of malocclusion in a few months and encouraging favorable skeletal growth in the future.

  19. Impacts of Imported Liquefied Natural Gas on Residential Appliance Components: Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    Lekov, Alex; Sturges, Andy; Wong-Parodi, Gabrielle

    2009-12-09

    An increasing share of natural gas supplies distributed to residential appliances in the U.S. may come from liquefied natural gas (LNG) imports. The imported gas will be of a higher Wobbe number than domestic gas, and there is concern that it could produce more pollutant emissions at the point of use. This report will review recently undertaken studies, some of which have observed substantial effects on various appliances when operated on different mixtures of imported LNG. While we will summarize findings of major studies, we will not try to characterize broad effects of LNG, but describe how different components of the appliance itself will be affected by imported LNG. This paper considers how the operation of each major component of the gas appliances may be impacted by a switch to LNG, and how this local impact may affect overall safety, performance and pollutant emissions.

  20. 38 CFR 17.122 - Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices...

    Science.gov (United States)

    2010-07-01

    ... of the expenses of repairs to prosthetic appliances and similar devices furnished without prior... Payment or reimbursement of the expenses of repairs to prosthetic appliances and similar devices furnished without prior authorization. The expenses of repairs to prosthetic appliances, or similar appliances...

  1. The impact of orthodontic appliances on eating - young people's views and experiences.

    Science.gov (United States)

    Carter, Louise A; Geldenhuys, Mieke; Moynihan, Paula J; Slater, Dina R; Exley, Catherine E; Rolland, Sarah L

    2015-06-01

    Orthodontic appliances are known to cause patients difficulty with eating. Learning more about the issues patients face, while eating with orthodontic appliances in place, will allow us to create more informative and relevant patient information, thereby improving patient compliance and treatment success. This study aims to understand how orthodontic appliances impact on eating in the broader context and to explore adolescent patients' perceptions of eating with orthodontic appliances. Purposive sampling was used and 19 participants currently undergoing orthodontic treatment and aged 11-14 years were selected for either a focus group or semi-structured interview to explore eating-related issues. Data collection and analysis were carried out as an iterative process broadly following principles of thematic analysis. Data collection ceased when no new themes emerged. Two main themes relating to eating problems emerged: restriction of food choice and problems associated with the eating process. Participants reported restricting food choice due to physical aspects of the appliance, advice given by their orthodontist, fear of breakage and also to minimize embarrassment. Participants also reported problems with the time taken to eat, chewing problems, taste change and being messy while eating. Additionally, time in treatment, the location of eating and relationship with those present during eating influenced emotions. Some participants indicated a positive impact of orthodontic appliances on their diet. These results can be used to further inform dietary advice offered to patients. Factors were identified which may not be considered in clinical practice but which could improve the value of dietary advice given to patients.

  2. Full 3-dimensional digital workflow for multicomponent dental appliances: A proof of concept.

    Science.gov (United States)

    van der Meer, W Joerd; Vissink, Arjan; Ren, Yijin

    2016-04-01

    The authors used a 3-dimensional (3D) printer and a bending robot to produce a multicomponent dental appliance to assess whether 3D digital models of the dentition are applicable for a full digital workflow. The authors scanned a volunteer's dentition with an intraoral scanner (Lava Chairside Oral Scanner C.O.S., 3M). A digital impression was used to design 2 multicomponent orthodontic appliances. Biocompatible acrylic baseplates were produced with the aid of a 3D printer. The metal springs and clasps were produced by a bending robot. The fit of the 2 appliances was assessed by 2 experienced orthodontists. The authors assessed both orthodontic appliances with the volunteer's dentition and found the fit to be excellent. Clinicians can fully produce a multicomponent dental appliance consisting of both an acrylic baseplate and other parts, such as clasps, springs, or screws, using a digital workflow process without the need for a physical model of the patient's dentition. Plaster models can be superfluous for orthodontic treatment as digital models can be used in all phases of a full digital workflow in orthodontics. The arduous task of making a multicomponent dental appliance that involves bending wires can possibly be replaced by a computer, design software, a 3D printer, and a bending robot. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

  3. Estimation of urban residential electricity demand in China using household survey data

    International Nuclear Information System (INIS)

    Zhou, Shaojie; Teng, Fei

    2013-01-01

    This paper uses annual urban household survey data of Sichuan Province from 2007 to 2009 to estimate the income and price elasticities of residential electricity demand, along with the effects of lifestyle-related variables. The empirical results show that in the urban area of Sichuan province, the residential electricity demand is price- and income-inelastic, with price and income elasticities ranging from −0.35 to −0.50 and from 0.14 to 0.33, respectively. Such lifestyle-related variables as demographic variables, dwelling size and holdings of home appliances, are also important determinants of residential electricity demand, especially the latter. These results are robust to a variety of sensitivity tests. The research findings imply that urban residential electricity demand continues to increase with the growth of income. The empirical results have important policy implications for the Multistep Electricity Price, which been adopted in some cities and is expected to be promoted nationwide through the installation of energy-efficient home appliances. - Highlights: • We estimate price and income elasticities in China using household survey data. • The current study is the first such study in China at this level. • Both price and income are inelastic. • Behavior factors have important impact on electricity consumption

  4. Oral radiation protector appliance

    International Nuclear Information System (INIS)

    Persico, T.M.; Dudas, R.M.; Shusta, G.W.

    1982-01-01

    An appliance for protecting teeth, gingiva, periodontal or alveola bone, salivary glands, and adjacent body areas against the harmful side effects of radiation therapy consists of an intraoral portion and an extraoral portion that may be selectively attached. The intraoral portion is substantially u-shaped to encompass the teeth and adjacent areas. The intraoral part may be made of lead sheet coated with plastic; the extraoral portion may be of lead sheet

  5. FIXED OR REMOVABLE APPLIANCE FOR EARLY ORTHODONTIC TREATMENT OF FUNCTIONAL ANTERIOR CROSSBITE.

    Science.gov (United States)

    Wiedel, Anna-Paulina

    2015-01-01

    Anterior crossbite with functional shift also called pseudo Class III is a malocclusion in which the incisal edges of one or more maxillary incisors occlude with the incisal edges of the mandibular incisors in centric relationship: the mandible and mandibular incisors are then guided anteriorly in central occlusion resulting in an anterior crossbite. Early correction, at the mixed dentition stage, is recommended, in order to avoid a compromising dentofacial condition which could result in the development of a true Class III malocclusion and temporomandibular symptoms. Various treatment options are available. The method of choice for orthodontic correction of this condition should not only be clinically effective, with long-term stability, but also cost-effective and have high patient acceptance, i.e. minimal perceived pain and discomfort. At the mixed dentition stage, the condition may be treated by fixed (FA) or removable appliance (RA). To date there is insufficient evidence to determine the preferred method. The overall aim of this thesis was therefore to compare and evaluate the use of FA and RA for correcting anterior crossbite with functional shift in the mixed dentition, with special reference to clinical effectiveness, stability, cost-effectiveness and patient perceptions. Evidence-based, randomized controlled trial (RCT) methodology was used, in order to generate a high level of evidence. The thesis is based on the following studies: The material comprised 64 patients, consecutively recruited from the Department of Orthodontics, Faculty of Odontology, Malmö University, Sweden and from one Public Dental Health Service Clinic in Malmö, Skane County Council, Sweden. The patients were no syndrome and no cleft patients. The following inclusion criteria were applied: early to late mixed dentition, anterior crossbite affecting one or more incisors with functional shift, moderate space deficiency in the maxilla, no inherent skeletal Class III discrepancy, ANB

  6. A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization.

    Science.gov (United States)

    Ozkalayci, Nurhat; Yetmez, Mehmet

    2016-01-01

    The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

  7. Using the internet of things to enable electrical load optimisation

    CSIR Research Space (South Africa)

    Butgereit, L

    2012-05-01

    Full Text Available about itself and also allowing the object to be controlled by some process. This paper describes a research project in balancing the electrical load in the kitchens of an IT organisation. Ten kitchen appliances were enhanced with digital intelligence...

  8. Challenge: Getting Residential Users to Shift Their Electricity Usage Patterns

    DEFF Research Database (Denmark)

    Brewer, Robert S.; Verdezoto, Nervo; Rasmussen, Mia Kruse

    2015-01-01

    electricity use from the less desirable times to more desirable times, including: feedback technology, pricing incentives, smart appliances, and energy storage. Based on our experience in this area, we present three challenges for residential shifting: getting users to understand the concept of shifting...

  9. 33 CFR 150.506 - When must the operator service inflatable lifesaving appliances and marine evacuation systems?

    Science.gov (United States)

    2010-07-01

    ... inflatable lifesaving appliances and marine evacuation systems? 150.506 Section 150.506 Navigation and...: OPERATIONS Emergency and Specialty Equipment Inflatable Lifesaving Appliances § 150.506 When must the operator service inflatable lifesaving appliances and marine evacuation systems? (a) The operator must...

  10. Adverse reactions to orthodontic appliances in nickel-allergic patients.

    Science.gov (United States)

    Volkman, Kristen K; Inda, Michael J; Reichl, Peter G; Zacharisen, Michael C

    2007-01-01

    Nickel allergy (NA) is common and causes more cases of allergic contact dermatitis (ACD) than all other metals combined. Many orthodontic appliances (ODAs) contain nickel but their clinical relevance in nickel-allergic patients is unclear. We aimed to characterize the relationship between NA and ODAs because the medical literature investigating this is controversial. A survey concerning adverse reactions to ODAs in patients with NA was distributed to members of the Wisconsin Society of Orthodontics. Forty-three surveys were analyzed. The surveyed group was experienced, representing a mean of 21.2 years in practice and averaging 242 appliances placed per year per orthodontist. Most new patients with orthodontia were 10-18 years old. Most wires used were nickel-titanium alloy. Although 76% of orthodontists inquired about NA at initial evaluation, 37% still placed nickel-containing ODAs in known nickel-allergic patients. Fifty percent placed a single intraoral appliance, observing for reactions. Three orthodontists applied ODAs to the skin similar to patch testing. Only 8 patients with reactions to ODAs were described in detail, 6 were female patients and 6 were aged 13-14 years. Intraoral and extraoral reactions were mild; diffuse urticaria was reported in one patient. Treatment included removing the appliances or changing to nonnickel alternatives with favorable outcomes. These cases, which included >33,000 patients, suggest a prevalence of 0.03%. Adverse reactions to ODAs in patients with NA have been observed but are uncommon. Using suitable alternatives, patients usually can be accommodated.

  11. Recolonization of mutans steptococci on teeth with orthodontic appliances after antimicrobial therapy.

    Science.gov (United States)

    Attin, R; Thon, C; Schlagenhauf, U; Werner, C; Wiegand, A; Hannig, C; Attin, T

    2005-10-01

    The aim of the present study was to compare the recolonization pattern of mutans streptococci on densely colonized teeth with and without fixed orthodontic appliances after treatment with a 40 per cent chlorhexidine (CHX) varnish (EC 40, Explore). Healthy subjects free of carious lesions requiring fixed orthodontic appliance treatment but with high bacterial mutans streptococci saliva counts were recruited (n = 10). For baseline registration, plaque from buccal sites was sampled and cultivated on Dentocult strips. Following professional tooth cleaning, CHX varnish was applied to all teeth for 8 minutes. Subsequently, orthodontic brackets and bands were inserted in either the upper or lower arch. Eight weeks after varnish application the degree of recolonization with mutans streptococci was reassessed on the buccal sites. Statistical analysis showed that recolonization with mutans streptococci was significantly higher (P < 0.05) on teeth with orthodontic appliances. The results indicate that the use of fixed orthodontic appliances creates artificial environments suitable for the proliferation of mutans streptococci after CHX varnish suppression.

  12. Projected electricity savings from implementing minimum energy efficiency standard for household refrigerators in Malaysia

    International Nuclear Information System (INIS)

    Mahlia, T.M.I.; Masjuki, H.H.; Saidur, R.; Choudhury, I.A.; NoorLeha, A.R.

    2003-01-01

    The Malaysian economy has grown rapidly in the last two decades. This growth has increased the ownership of household electrical appliances, especially refrigerator-freezers. Almost every house in Malaysia owns a refrigerator-freezer. The Malaysia Energy Center considered implementing a minimum energy efficiency standard for household refrigerator-freezers sometime in the coming year. This paper attempts to predict the amount of energy savings in the residential sector by implementing a minimum energy efficiency standard for household refrigerator-freezers. The calculations are based on the growth of refrigerator-freezer ownership data in Malaysian households. By implementing the programs in 2004, about 8722 GWh will be saved in the year 2013. Therefore, efficiency improvement of this appliance will provide a significant impact in future electricity consumption in Malaysia

  13. Orthodontic parotitis: a rare complication from an orthodontic appliance.

    Science.gov (United States)

    McCarthy, Eileen; Cobb, Alistair R M

    2012-12-01

    A case is presented of a 14-year-old female undergoing orthodontic fixed appliance treatment who presented with right facial swelling in the parotid region. An initial diagnosis of acute infective parotitis was made by her primary care clinician. However, after clinical examination and ultrasonographic imaging, a diagnosis of salivary stasis secondary to inflammatory occlusion of Stensen's ductal orifice was made. The ductal orifice had been traumatized by the adjacent orthodontic appliance. This has not been described before in the literature. The differential diagnosis of parotid enlargement in children is discussed.

  14. Energy efficiency to reduce residential electricity and natural gas use under climate change.

    Science.gov (United States)

    Reyna, Janet L; Chester, Mikhail V

    2017-05-15

    Climate change could significantly affect consumer demand for energy in buildings, as changing temperatures may alter heating and cooling loads. Warming climates could also lead to the increased adoption and use of cooling technologies in buildings. We assess residential electricity and natural gas demand in Los Angeles, California under multiple climate change projections and investigate the potential for energy efficiency to offset increased demand. We calibrate residential energy use against metered data, accounting for differences in building materials and appliances. Under temperature increases, we find that without policy intervention, residential electricity demand could increase by as much as 41-87% between 2020 and 2060. However, aggressive policies aimed at upgrading heating/cooling systems and appliances could result in electricity use increases as low as 28%, potentially avoiding the installation of new generation capacity. We therefore recommend aggressive energy efficiency, in combination with low-carbon generation sources, to offset projected increases in residential energy demand.

  15. Overview of the Electricity Research Programme 2002

    Energy Technology Data Exchange (ETDEWEB)

    Brueniger, R.

    2003-07-01

    This publication of the Swiss Federal Office of Energy (SFOE) presents a review in English of the SFOE's Electricity Research Programme's main areas of activity in 2002. These include electricity distribution, high-temperature superconductors, energy and information technology, electric drives and motors and appliances. Tasks accomplished and results obtained are quoted. In the electricity distribution area these include educational topics, modelling of power lines, independent energy producers and corrosion in pipelines caused by alternating current. High-temperature superconductors, their impact and market impact are discussed. In the energy and information area, a competence centre is introduced, the energy efficiency of computer networks is looked at, including documentation for requests for tender for personal computers. Also, uninterruptible power supplies are looked at. Further the efficiency of an 'intelligent' house is reviewed and the power consumption of process control units is examined. As far as drives and electric motors are concerned, an industry convention is examined and work in the European Motor Challenge Programme is looked at. Gearless drives are looked at as are energy-efficient motors in general. In the devices area, topics range from heat-pump tumble-dryers, the GreenLight Contact Points project, electric band heaters and the optimal use of energy in refrigerated water, beverage and food dispensers as well as in dispensers providing hot drinks. The stand-by consumption of household appliances is also discussed. National and international co-operation is reviewed and various pilot and demonstration projects in the above-mentioned areas are briefly presented. The report is completed with a list of research and development projects and a list of pilot and demonstration work.

  16. Evolution of treatment mechanics and contemporary appliance design in orthodontics: A 40-year perspective.

    Science.gov (United States)

    McLaughlin, Richard P; Bennett, John C

    2015-06-01

    Until the early 1970s, successful treatment with the Begg technique and the Tweed edgewise technique required tedious wire bending. The introduction of Andrews' straight wire appliance changed that, and it was one of the most significant contributions in the history of orthodontics. The straight wire appliance significantly reduced the amount of wire bending and also brought along other options in treatment mechanics. Retraction of the canines with elastic chains and ligature wires became more common. Sliding mechanics in place of closing loops became the method of space closure for a significant number of clinicians. Edgewise force levels were initially used to close spaces; however, it was soon observed that lighter forces were more effective with sliding mechanics. Along with these changes, it became apparent that compensation in the appliance was needed, depending on the type of malocclusion and particularly with varying extraction sequences. Various appliance designs were developed to accommodate changes in mechanics and force levels. These modifications improved tooth positions at the end of treatment as long as the brackets were properly placed. These major changes in appliances, force levels, and treatment mechanics can be traced back to the work of Dr Lawrence Andrews and the straight wire appliances. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  17. Lingual vs. labial fixed orthodontic appliances: systematic review and meta-analysis of treatment effects.

    Science.gov (United States)

    Papageorgiou, Spyridon N; Gölz, Lina; Jäger, Andreas; Eliades, Theodore; Bourauel, Christoph

    2016-04-01

    The aim of this systematic review was to compare the therapeutic and adverse effects of lingual and labial orthodontic fixed appliances from clinical trials on human patients in an evidence-based manner. Randomized and prospective non-randomized clinical trials comparing lingual and labial appliances were included. Risk of bias within and across studies was assessed using the Cochrane tool and the Grading of Recommendations Assessment, Development and Evaluation (GRADE) approach. Random-effects meta-analyses were conducted, followed by subgroup and sensitivity analyses. Six electronic databases were searched from inception to July 2015, without limitations. A total of 13 papers pertaining to 11 clinical trials were included with a total of 407 (34% male/66% female) patients. Compared with labial appliances, lingual appliances were associated with increased overall oral discomfort, increased speech impediment (measured using auditory analysis), worse speech performance assessed by laypersons, increased eating difficulty, and decreased intermolar width. On the other hand, lingual appliances were associated with increased intercanine width and significantly decreased anchorage loss of the maxillary first molar during space closure. Based on existing trials, there is insufficient evidence to make robust recommendations for lingual fixed orthodontic appliances regarding their therapeutic or adverse effects, as the quality of evidence was low. © 2016 Eur J Oral Sci.

  18. An International Survey of Electric Storage Tank Water Heater Efficiency and Standards

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Alissa; Lutz, James; McNeil, Michael A.; Covary, Theo

    2013-11-13

    Water heating is a main consumer of energy in households, especially in temperate and cold climates. In South Africa, where hot water is typically provided by electric resistance storage tank water heaters (geysers), water heating energy consumption exceeds cooking, refrigeration, and lighting to be the most consumptive single electric appliance in the home. A recent analysis for the Department of Trade and Industry (DTI) performed by the authors estimated that standing losses from electric geysers contributed over 1,000 kWh to the annual electricity bill for South African households that used them. In order to reduce this burden, the South African government is currently pursuing a programme of Energy Efficiency Standards and Labelling (EES&L) for electric appliances, including geysers. In addition, Eskom has a history of promoting heat pump water heaters (HPWH) through incentive programs, which can further reduce energy consumption. This paper provides a survey of international electric storage water heater test procedures and efficiency metrics which can serve as a reference for comparison with proposed geyser standards and ratings in South Africa. Additionally it provides a sample of efficiency technologies employed to improve the efficiency of electric storage water heaters, and outlines programs to promote adoption of improved efficiency. Finally, it surveys current programs used to promote HPWH and considers the potential for this technology to address peak demand more effectively than reduction of standby losses alone

  19. Marginal cost of electricity conservation: an application of linear program

    International Nuclear Information System (INIS)

    Silveira, A.M. da; Hollanda, J.B. de

    1987-01-01

    This paper is addressed ti the planning of electricity industry when the use of energetically efficient appliances (conservation) is financed by the utilities. It is based on the Linear Programming Model proposed by Masse and Boiteaux for planning of conventional energy sources, where one unity of electricity (Kw/Kw h) saved is treated as if it were a generator of equivalent size. In spite of the formal simplicity of the models it can support interesting concessions on the subject of a electrical energy conservation policy. (author)

  20. A New Orthodontic Appliance with a Mini Screw for Upper Molar Distalization

    Directory of Open Access Journals (Sweden)

    Nurhat Ozkalayci

    2016-01-01

    Full Text Available The aim of this study is to present a new upper molar distalization appliance called Cise distalizer designed as intraoral device supported with orthodontic mini screw for upper permanent molar distalization. The new appliance consists of eight main components. In order to understand the optimum force level, the appliance under static loading is tested by using strain gage measurement techniques. Results show that one of the open coils produces approximately 300 gr distalization force. Cise distalizer can provide totally 600 gr distalization force. This range of force level is enough for distalization of upper first and second molar teeth.

  1. 21 CFR 872.5410 - Orthodontic appliance and accessories.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Therapeutic Devices § 872.5410 Orthodontic appliance and... device includes the preformed orthodontic band, orthodontic band material, orthodontic elastic band...

  2. The stoma appliances market in five European countries: a comparative analysis.

    Science.gov (United States)

    Cornago, Dante; Garattini, Livio

    2002-01-01

    This comparative exercise analysed the domestic market for stoma appliances in five European countries--Denmark, France, Germany, Italy and the United Kingdom. National legislation, prescription procedures, delivery modalities and the market were investigated in each country. The analysis involved reviewing national and international literature on stoma appliances and interviewing a selected expert panel of market operators in each country comprising at least one health authority representative, one distributor of medical devices and one manufacturer. No specific relationship was found between the health care system framework and the stoma market, except for a greater inclination towards home care in national health services. All five countries reimburse stoma bags, but the distribution of these appliances varies widely, ranging from Denmark, where home delivery is mandatory, to Italy, where any channel can be used. The comparative analysis underlined two important features of the stoma bag market: the discretion of enterostomists in directing patients towards a specific brand of bags, and the patients' high brand loyalty. Despite that, the analysis did not identify any single country that could be considered a benchmark for stoma bag regulation. Each country deals with stoma appliances in different ways, making this a very fragmented market.

  3. Orthodontic treatment with a series of removable appliances.

    Science.gov (United States)

    Chenin, David A; Trosien, Andrew H; Fong, Patricia F; Miller, Robert A; Lee, Rodney S

    2003-09-01

    In the United States, the demand for straight white teeth has never been more important to patients. Crowded, poorly aligned teeth are not esthetically pleasing and are difficult to keep clean. However, until recently, the process of straightening the teeth typically has involved appliances involving bands, brackets and wires that also can be difficult to clean. The desire for a cosmetic solution to misaligned teeth has led to an increase in the number of patients seeking veneers, crowns and other laboratory-fabricated cosmetic restorations. Some clinicians are not aware that there are other ways to align teeth without either significant enamel reduction or conspicuous fixed orthodontic appliances. An alternative method of treatment, involving a series of clear removable appliances, circumvents this shortcoming and enables tooth alignment while avoiding deterioration in the cosmetics of the smile during treatment. This article describes a method of treatment, Invisalign (Align Technology, Santa Clara, Calif.), that clinicians can use in conjunction with 3-D computer models to accomplish the esthetic and oral hygiene objectives during and after treatment. The authors present three case reports, all involving a chief concern of crowding. The first case involved treatment of both arches by interproximal reduction, alignment of teeth and leveling the curve of Spee. The second case involved treatment of both arches by proclination, expansion and minor interproximal reduction. The final case shows relief of lower-arch crowding via lower-incisor extraction. In addition to satisfying the patient's chief concern of desiring straight teeth, this method of treatment satisfies additional objectives of esthetic treatment and esthetic results with significant oral hygiene benefits. Clinicians can address a patient's chief concern effectively without requiring an inventory of appliances (such as bands, brackets, wires and instruments). Furthermore, the use of 3-D computer models

  4. Evaluation of photo-activation appliances used in dentistry

    Directory of Open Access Journals (Sweden)

    Thales Ribeiro de Magalhães Filho

    2008-01-01

    Full Text Available Objective: Verify the Vickers microhardness promoted by three photo-activation appliances: one Halogen Light Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil and two Light Emitting Diodes. One with a larger diode (Ultraled, Dabi-Atlante, Ribeirão Preto, Brazil and the other with seven smaller diodes (Ultraled xp, Dabi-Atlante, Ribeirão Preto, Brazil in composites with different matrixes. Methods: Three test specimens were made for each resinous materials using silicone molds measuring 4 X 8 X 30 mm. Polymerization was performedin three stages and on the two surfaces. After having been submitted to careful polishing with sequential abrasive papers and diamond paste, the Vickers microhardness of the test specimens was determined. Afterwards these values were submitted to statistical analysis by the ANOVA table and Student’s-t test. Results: The microhardness values obtained in the hybrid composite were as follows: 51.63 kg/mm2 +- 3.27; 52.22 kg/mm2 +- 3.3; 38.08 kg/mm2 +-0.31 and in the ormocer, 41.87 kg/mm2 +- 2.36; 41.5 kg/mm2 +- 1.2; 33.63 kg/mm2 +- 1.2, by the Ultralux (Dabi-Atlante, Ribeirão Preto, Brazil, Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil appliances, respectively. Conclusion: The Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil and Ultraled xp (Dabi-Atlante, Ribeirão Preto, Brazil appliances promoted microhardness values that were similar between them and higher than the values produced by Ultraled (Dabi-Atlante, Ribeirão Preto, Brazil in the composites. It was verified that the intensity of the photo-activator appliances is directly related to the microhardness they produce in the composites.

  5. The effect of e-learning on the quality of orthodontic appliances

    Directory of Open Access Journals (Sweden)

    Schorn-Borgmann S

    2015-08-01

    Full Text Available Stephanie Schorn-Borgmann,1 Carsten Lippold,2 Dirk Wiechmann,3 Thomas Stamm2 1Private Practice, Nordkirchen, Germany; 2Department of Orthodontics, University of Münster, Münster, Germany; 3Department of Orthodontics, University of Hannover, Hannover, Germany Purpose: The effect of e-learning on practical skills in medicine has not yet been thoroughly investigated. Today’s multimedia learning environment and access to e-books provide students with more knowledge than ever before. The aim of this study is to evaluate the effect of online demonstrations concerning the quality of orthodontic appliances manufactured by undergraduate dental students. Materials and methods: The study design was a parallel-group randomized clinical trial. Fifty-four participants were randomly assigned to one of the three groups: 1 conventional lectures, 2 conventional lectures plus written online material, and 3 access to resources of groups one and two plus access to online video material. Three orthodontic appliances (Schwarz Plate, U-Bow Activator, and Fränkel Regulator were manufactured during the course and scored by two independent raters blinded to the participants. A 15-point scale index was used to evaluate the outcome quality of the appliances. Results: In general, no significant differences were found between the groups. Concerning the appliances, the Schwarz Plate obtained the highest scores, whereas the Fränkel Regulator had the lowest scores; however, these results were independent of the groups. Females showed better outcome scores than males in groups two and three, but the difference was insignificant. Age of the participants also had no significant effect. Conclusion: The offer that students could use additional time and course-independent e-learning resources did not increase the outcome quality of the orthodontic appliances. The advantages of e-learning observed in the theoretical fields of medicine were not achieved in the educational

  6. Evaluation of dentoskeletal effects of Farmand functional appliance (Fa II) on class II malocclusion

    OpenAIRE

    Yassaei S.; Aghili H.; Razeghi D.

    2007-01-01

    Background and Aim: Functional appliances refer to a variety of removable or fixed appliances designed to alter the mandibular position both sagitally and vertically, resulting in orthodontic and orthopedic changes. Despite the long history of functional appliances, there is still much controversy related to their effectiveness and mode of action. The aim of this study was to evaluate dental and skeletal effects of Fa II in patients with class II malocclusion due to mandibular deficiency.Mate...

  7. Influence of orthodontic appliance-derived artifacts on 3-T MRI movies.

    Science.gov (United States)

    Ozawa, Erika; Honda, Ei-Ichi; Parakonthun, Kulthida Nunthayanon; Ohmori, Hiroko; Shimazaki, Kazuo; Kurabayashi, Tohru; Ono, Takashi

    2018-02-19

    Magnetic resonance imaging (MRI) has been used to study configurations of speech organs in the resting state. However, MRI is sensitive to metals, and numerous types of metallic appliances, most of which have a large magnetic susceptibility, are used in orthodontic treatment and may cause severe artifacts on MRI. We have developed techniques for obtaining MRI movies of the oral region, to evaluate articulatory changes, especially movement of the tongue, palate, and teeth, pre- and post-orthodontic/orthognathic treatment. We evaluated the influence of artifacts caused by orthodontic appliances, including fixed retainers, metal brackets, and wires, on measurements in 3-T MRI movies. Sixteen healthy young adults (nine males, seven females; average age, 27 years) with normal occlusion were recruited. Four types of customized maxillary and mandibular plates were prepared by incorporating one of the following into the plate: (a) nothing, (b) a fixed canine-to-canine retainer, (c) metal brackets for the anterior and molar teeth, or (d) clear brackets for the anterior teeth and metal brackets for molars. A 3-T MRI movie, in segmented cine mode, was generated for each plate condition while participants pronounced a vowel-consonant-vowel syllable (/asa/). The size of the artifact due to the metallic brackets was measured. The face size and orthodontically important anatomical structures, such as the velum, the hard palate, and the laryngeal ventricle, were also measured. A large artifact was observed over the entire oral region around orthodontic appliances, altering regional visibility. The velopharyngeal height was measured as significantly longer in the presence of metal brackets. The maximum artifact size due to a metallic bracket was > 8 cm. Our results show that even if it is possible to obtain the measurements of palate length, nasion to sella, and nasion to basion in individuals wearing metal brackets for molars, the measurements might be affected due to the

  8. Do different maxillary expansion appliances influence the outcomes of the treatment?

    Science.gov (United States)

    Algharbi, Muteb; Bazargani, Farhan; Dimberg, Lillemor

    2018-01-23

    There is no consensus in the literature regarding which rapid maxillary expansion (RME) design or activation rate benefits the patients the most. Therefore, the primary aim of this systematic review was to see whether there is a difference in the skeletal and dentoalveolar effects of different RME appliances in children and growing adolescents. The secondary aim was to see whether these effects are different when using different activation protocols for these appliances. The search was done in three databases (PubMed, Cochrane Library, and Web of Science). The following inclusion criteria were used: randomized controlled trial, prospective controlled studies, 15 or more patients in each study, human subjects up to 18 years of age, and RME effects had to be assessed by computed tomography/cone beam computed tomography. Quality of the methodology was classified according to the Grading of Recommendations Assessment, Development and Evaluation (GRADE) guidelines as high, moderate, or low. The search resulted in 145 titles and abstracts; 109 of them were excluded based on pre-established criteria. Thirty-six full-text articles were assessed for eligibility and 18 of which satisfied the inclusion criteria. Finally, seven articles were deemed eligible for full inclusion and revealed that all appliances and protocols showed significant expansion in the mid-palatal suture. No evidence was found for the cause of dental tipping. In this systematic review, having different age groups in each study and using different anatomical landmarks and outcome measures for assessing the skeletal and dental effects made it difficult to conduct a meta-analysis. There is moderate evidence that all designs produce significant expansion at the mid-palatal suture. However, lack of studies comparing appliances and protocols has been found. Finally, no evidence-based conclusions could be drawn about the appliance effect on teeth tipping. No appliance appears to be superior when it comes to

  9. 49 CFR 236.312 - Movable bridge, interlocking of signal appliances with bridge devices.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Movable bridge, interlocking of signal appliances with bridge devices. 236.312 Section 236.312 Transportation Other Regulations Relating to... SYSTEMS, DEVICES, AND APPLIANCES Interlocking Standards § 236.312 Movable bridge, interlocking of signal...

  10. Changes in subgingival microflora after placement and removal of fixed orthodontic appliances

    Directory of Open Access Journals (Sweden)

    Živković-Sandić Marija

    2014-01-01

    Full Text Available Introduction. The placement of fixed orthodontic appliances may lead to increased plaque accumulation and changes in subgingival microflora. Objective. The aim of this study was to examine the changes in frequency of subgingival microflora that occur after placement and removal of fixed orthodontic appliance using polymerase chain reaction (PCR. Methods. This study included 33 orthodontic patients, who were divided into two groups. Subgingival plaque samples were collected from the right upper incisor (U1 and right upper first molar (U6. In group A, the samples were taken three times: before placement appliance (T1, after one month (T2, and after 3 months (T3. In group B the samples were also taken three times: before appliance removal (T1, after one month (T2, and after three months (T3. PCR method was used to determine the presence of P. gingivalis, A. actinomycetemcomitans, T. forsythia, and P. intermedia. Results. In group A the frequency of P. gingivalis showed statistically significant decrease at U1 (p=0.049 and U6 (p=0.008, from T1 to T2, and at U1 (p=0.048 from T1 to T3. In group B only the frequency of T. forsythia showed a statistically significant decrease, at U6 (T1 vs. T2, p=0.004; T1 vs. T3, p=0.0003. Regarding other analyzed bacteria, changes in the presence were noticed but no statistical significance was found. Conclusion. Placement of fixed appliances may have an impact on subgingival microflora, but in the first months after the placement and removal of the appliance changes were not significant, probably due to good oral hygiene. [Projekat Ministarstva nauke Republike Srbije, br. 175075

  11. Space Maintenance with an Innovative "Tube and Loop" Space Maintainer (Nikhil Appliance).

    Science.gov (United States)

    Srivastava, Nikhil; Grover, Jyotika; Panthri, Prerna

    2016-01-01

    Despite the best efforts in prevention, premature loss of primary teeth continues to be a common problem in pediatric dentistry, resulting in disruption of arch integrity and adversely affecting the proper alignment of permanent successors. Space maintainers (SMs) are special appliances used for maintaining space created due to premature loss of primary teeth. Band and loop SM is mostly indicated for the premature loss of single primary molar, but this appliance has a number of limitations both for operators and for patients. Presented in this article is an innovative "Tube and Loop" SM (Nikhil appliance) which offers several advantages over the conventional band and loop SM. It is not only easy and quick to fabricate but can also be completed in a single sitting and cumbersome steps like impression making and laboratory procedures namely soldering are eliminated. How to cite this article: Srivastava N, Grover J, Panthri P. Space Maintenance with an Innovative "Tube and Loop" Space Maintainer (Nikhil Appliance). Int J Clin Pediatr Dent 2016;9(1):86-89.

  12. Mapping chemical elements on the surface of orthodontic appliance by SEM-EDX.

    Science.gov (United States)

    Mikulewicz, Marcin; Wołowiec, Paulina; Michalak, Izabela; Chojnacka, Katarzyna; Czopor, Wojciech; Berniczei-Royko, Adam; Vegh, Andras; Gedrange, Thomas

    2014-05-25

    During orthodontic treatment, the various elements that constitute the fixed appliance undergo different processes. As a result of a change of the surface, elution/coverage of metals on the surface can be observed in the process of corrosion/passivation. Scanning electron microscopy with an energy-dispersive X-ray analytical system (SEM-EDX) was used to analyze the composition of stainless steel elements of orthodontic fixed appliances (before and after orthodontic treatment), to obtain the composition of the surface of the elements. The analyzed elements were: brackets (Victory Series APC PLUS 022, 3M Unitek, Monrovia, CA, USA); wires (0.017×0.025, 3M Unitek, Monrovia, CA, USA); and bands (37+, 3M Unitek, Monrovia, CA, USA). The results showed a decrease of chromium and iron contribution to the surface, with increase of oxygen content in used vs. new elements of the appliance. Our results confirm the formation of oxides (passivation layer) on the surface of stainless steel as a result of the presence of the orthodontic appliance in patients' oral cavities.

  13. Created in Close Interaction with the Industry: The Smart Appliances REFerence (SAREF) Ontology

    NARCIS (Netherlands)

    Daniele, L.M.; Hartog, F.T.H. den; Roes, J.B.M.

    2015-01-01

    Around two thirds of the energy consumed by buildings can be traced back to the residential sectors and thus household appliances. Today, most appliances are highly intelligent and networked devices, in principle being able to form complete energy consuming, producing, and managing systems. Reducing

  14. Alternative test method to assess the energy performance of frost-free refrigerating appliances

    International Nuclear Information System (INIS)

    Hermes, Christian J.L.; Melo, Cláudio; Knabben, Fernando T.

    2013-01-01

    This paper outlines an alternative test method to evaluate the energy consumption of frost-free refrigerators and freezers for residential applications. While the standardized methods require the refrigerating appliance to be kept running according to its onboard control system, which usually drives the refrigerator through an on–off cycling pattern, the proposed approach assesses the refrigerator energy performance in the steady-state regime, being therefore much faster and more reliable. In this procedure, the cooling capacity is matched to the cooling loads by PID-controlled electrical heaters installed within the refrigerated compartments, so that the compartment temperatures are kept at the desired standardized levels. Comparisons between the experimental results obtained using the steady-state energy test and the standardized procedures showed that the former follows closely the trends observed for the latter. - Highlights: ► An alternative test method to assess the energy consumption of refrigerators is proposed. ► PID-controlled electrical heaters were installed within the compartments. ► Steady-state and ISO energy tests were performed and compared. ► Both proposed and standardized test procedures showed similar trends.

  15. A randomized clinical trial comparing mandibular incisor proclination produced by fixed labial appliances and clear aligners.

    Science.gov (United States)

    Hennessy, Joe; Garvey, Thérèse; Al-Awadhi, Ebrahim A

    2016-09-01

    To compare the mandibular incisor proclination produced by fixed labial appliances and third generation clear aligners. Patients underwent a course of orthodontic treatment using either fixed labial appliances or clear aligners (Invisalign). Mandibular incisor proclination was measured by comparing pretreatment and near-end treatment lateral cephalograms. Eligibility criteria included adult patients with mild mandibular incisor crowding (clear aligner group. Baseline characteristics were similar for both groups: Fixed appliance mean crowding was 2.1 ± 1.3 mm vs clear aligner mean crowding, 2.5 ± 1.3 mm; pretreatment mean mandibular incisor inclination for the fixed appliance group was 90.8 ± 5.4° vs 91.6 ± 6.4° for the clear aligner group. Fixed appliances produced 5.3 ± 4.3° of mandibular incisor proclination. Clear aligners proclined the mandibular incisors by 3.4 ± 3.2°. The difference between the two groups was not statistically significant (P > .05). There was no difference in the amount of mandibular incisor proclination produced by clear aligners and fixed labial appliances in mild crowding cases.

  16. Open-bite treatment utilizing clear removable appliances with intermaxillary and intramaxillary elastics.

    Science.gov (United States)

    Park, Jae Hyun; Kim, Tae Weon

    2009-01-01

    Clear removable appliances with elastics can be effective and efficient in extruding maxillary teeth during aligner treatment or following a relapse of an open bite. Some patients with open bites refuse to wear conventional fixed appliances. In these individuals, clear aligners with elastics could be a valuable alternative. © 2009 Quintessence Publishing Co, Inc. All Rights Reserved

  17. 33 CFR 150.504 - When must the operator service and examine lifeboat and rescue boat launching appliances?

    Science.gov (United States)

    2010-07-01

    ... and examine lifeboat and rescue boat launching appliances? 150.504 Section 150.504 Navigation and...: OPERATIONS Emergency and Specialty Equipment Launching Appliances § 150.504 When must the operator service and examine lifeboat and rescue boat launching appliances? (a) The operator must service launching...

  18. The effect of e-learning on the quality of orthodontic appliances.

    Science.gov (United States)

    Schorn-Borgmann, Stephanie; Lippold, Carsten; Wiechmann, Dirk; Stamm, Thomas

    2015-01-01

    The effect of e-learning on practical skills in medicine has not yet been thoroughly investigated. Today's multimedia learning environment and access to e-books provide students with more knowledge than ever before. The aim of this study is to evaluate the effect of online demonstrations concerning the quality of orthodontic appliances manufactured by undergraduate dental students. The study design was a parallel-group randomized clinical trial. Fifty-four participants were randomly assigned to one of the three groups: 1) conventional lectures, 2) conventional lectures plus written online material, and 3) access to resources of groups one and two plus access to online video material. Three orthodontic appliances (Schwarz Plate, U-Bow Activator, and Fränkel Regulator) were manufactured during the course and scored by two independent raters blinded to the participants. A 15-point scale index was used to evaluate the outcome quality of the appliances. In general, no significant differences were found between the groups. Concerning the appliances, the Schwarz Plate obtained the highest scores, whereas the Fränkel Regulator had the lowest scores; however, these results were independent of the groups. Females showed better outcome scores than males in groups two and three, but the difference was insignificant. Age of the participants also had no significant effect. The offer that students could use additional time and course-independent e-learning resources did not increase the outcome quality of the orthodontic appliances. The advantages of e-learning observed in the theoretical fields of medicine were not achieved in the educational procedures for manual skills. Factors other than e-learning may have a higher impact on manual skills, and this should be investigated in further studies.

  19. Estimating returns to scale and scale efficiency for energy consuming appliances

    Energy Technology Data Exchange (ETDEWEB)

    Blum, Helcio [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Efficiency Standards Group; Okwelum, Edson O. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Energy Efficiency Standards Group

    2018-01-18

    Energy consuming appliances accounted for over 40% of the energy use and $17 billion in sales in the U.S. in 2014. Whether such amounts of money and energy were optimally combined to produce household energy services is not straightforwardly determined. The efficient allocation of capital and energy to provide an energy service has been previously approached, and solved with Data Envelopment Analysis (DEA) under constant returns to scale. That approach, however, lacks the scale dimension of the problem and may restrict the economic efficient models of an appliance available in the market when constant returns to scale does not hold. We expand on that approach to estimate returns to scale for energy using appliances. We further calculate DEA scale efficiency scores for the technically efficient models that comprise the economic efficient frontier of the energy service delivered, under different assumptions of returns to scale. We then apply this approach to evaluate dishwashers available in the market in the U.S. Our results show that (a) for the case of dishwashers scale matters, and (b) the dishwashing energy service is delivered under non-decreasing returns to scale. The results further demonstrate that this method contributes to increase consumers’ choice of appliances.

  20. Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air

    Energy Technology Data Exchange (ETDEWEB)

    Brand, L.

    2014-04-01

    This measure guideline covers how to assess and carry out the combustion safety procedures for appliances and heating equipment that uses indoor air for combustion in low-rise residential buildings. Only appliances installed in the living space, or in an area freely communicating with the living space, vented alone or in tandem with another appliance are considered here. A separate measure guideline addresses combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage that use outdoor air for combustion. This document is for inspectors, auditors, and technicians working in homes where energy upgrades are being conducted whether or not air infiltration control is included in the package of measures being applied. In the indoor combustion air case, guidelines summarized here are based on language provided in several of the codes to establish minimum requirements for the space using simplified prescriptive measures. In addition, building performance testing procedures are provided by testing agencies. The codes in combination with the test procedures offer comprehensive combustion safety coverage to address safety concerns, allowing inexperienced residential energy retrofit inspectors to effectively address combustion safety issues and allow energy retrofits to proceed.

  1. Research and Development of Natural Draft Ultra-Low Emissions Burners for Gas Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Therkelsen, Peter [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cheng, Robert [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sholes, Darren [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2017-08-31

    Combustion systems used in residential and commercial cooking appliances must be robust and easy to use while meeting air quality standards. Current air quality standards for cooking appliances are far greater than other stationary combustion equipment. By developing an advanced low emission combustion system for cooking appliances, the air quality impacts from these devices can be reduced. This project adapted the Lawrence Berkeley National Laboratory (LBNL) Ring-Stabilizer Burner combustion technology for residential and commercial natural gas fired cooking appliances (such as ovens, ranges, and cooktops). LBNL originally developed the Ring-Stabilizer Burner for a NASA funded microgravity experiment. This natural draft combustion technology reduces NOx emissions significantly below current SCAQMD emissions standards without post combustion treatment. Additionally, the Ring-Stabilizer Burner technology does not require the assistance of a blower to achieve an ultra-low emission lean premix flame. The research team evaluated the Ring-Stabilizer Burner and fabricated the most promising designs based on their emissions and turndown.

  2. Application of smart technology in monitoring and control of home appliances

    Directory of Open Access Journals (Sweden)

    A. A. Abdulrazaq

    2017-08-01

    Full Text Available The inherent dependency of home appliances on human for monitoring and control has been found to be mainly responsible for power wastage, and increase in the rate of wear and tear, which invariably implies additional spending on the part of owners. The smart technology provides a way out. This paper presents an automated system which is based on arduino and android device for monitoring and controlling appliances to prevent the wastage of power. The system design is based on the Microcontroller MIKRO-C software, active sensors and wireless internet services which is used in different monitoring and control processes of fan, air-conditioner, light and heater. The system when tested performs efficiently in monitoring and controlling through switching the appliances in the room based on human presence and environmental changes due to light intensity and temperature variation.

  3. A test procedure for energetic and performance analysis of cold appliances for the food industry

    International Nuclear Information System (INIS)

    Armani, F; Boscolo, A

    2013-01-01

    In this article we present a novel approach for the characterization of cold appliances and in particular of refrigerators based on the standard vapour compression cycle with a reciprocating on/off compressor. The test procedure is based on a virtual instrument that perform both the stimulus and the data acquisition on the device under test. Acquired data is elaborated to fit a semi-empirical model based on the energetic balances between thermal and electrical sub systems and the heat exchanged with the environment. This approach results in a simple method to calculate useful parameters of the refrigerator, such as energetic performance, cooling effect and limit values of thermal loads. The test procedure requires only a few temperatures and the electric power consumption to be monitored, resulting in a low impact on the refrigerator. Preliminary tests showed a good estimation of parameters and prediction of energy consumption and heat extraction capacity of the refrigerator under test

  4. Efficacy of the Nance appliance as an anchorage-reinforcement method.

    Science.gov (United States)

    Al-Awadhi, Ebrahim A; Garvey, Therese M; Alhag, Mohamed; Claffey, Noel M; O'Connell, Brian

    2015-03-01

    The Nance appliance is widely considered to be an efficient method of anchorage reinforcement; however, much of the perceived advantage is based on clinical judgment. The aim of this study was to assess the amounts of anchorage loss and desired tooth movement associated with the Nance appliance. The mandibular arches of 7 beagle dogs were used. The first and third premolars were extracted. Reference miniscrews were placed at the first premolar sites as stable references to measure the amounts of anchorage loss and desired tooth movement. Four beagles were fitted with custom-made Nance appliances on the fourth premolars and orthodontic bands on the second premolars (Nance group). Three beagles were fitted with orthodontic bands on the second and fourth premolars with no anchorage reinforcement (control group). The second premolars were retracted over 15 weeks in both groups. The amounts of second premolar movement (desired tooth movement) and fourth premolar movement (anchorage loss) were recorded at 5, 10, and 15 weeks. The percentages of desired tooth movement and anchorage loss to the total space closure were calculated. The mean desired tooth movement was significantly more in the Nance group than in the control group at 10 weeks (P appliance did not provide absolute anchorage, but there was significantly less anchorage loss with it than in the control group. The majority of anchorage loss occurred during the first 10 weeks in the Nance group. Copyright © 2015 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  5. Customer service in appliance sales departments of selected ...

    African Journals Online (AJOL)

    Customer service in appliance sales departments of selected prominent retail outlets: store manager, ... A single measurement of customers' perception of service quality in various stores however suggested ... AJOL African Journals Online.

  6. Corrosion of weldments in orthodontic appliances

    International Nuclear Information System (INIS)

    Vazquez, S.M.; Riesgo, O.; Duffo, G.S.

    1997-01-01

    The study of corrosion-related problems of dental materials has undergone a considerable development in recent years in order to avoid the use of materials with insufficient corrosion resistance in patients mouth. The subject of the present work was to study a particular type of corrosion: galvanic corrosion. One of the most common case of galvanic couples in patients mouth are the orthodontic appliances. The materials studied in the present work were stainless steel strips and silver-copper wires, isolated and welded between them. The electrochemical tests were performed in a NaCl 0.1M and Lactic Acid 0.1 M solution (pH2.3), and after test, the specimens were observed using the optical and scanning electron microscope. The results show that when stainless steel is coupled with a silver solder, the last is the anode of the galvanic couple. As a consequence of this, the silver solder undergone a severe attack. Stainless steel orthodontic appliances with silver solder are feasibly destroyed due to a severe attack on the filler metal disjoining the welded parts. (author) 9 refs

  7. Three case reports demonstrating treatment of relatively complex orthodontic cases using a completely customised lingual appliance.

    Science.gov (United States)

    Buckley, John

    2016-01-01

    It is a commonly held misconception among Irish dentists that only minor malocclusions can be treated with lingual appliances. This article demonstrates the use of contemporary completely customised lingual orthodontic appliances to treat a diverse range of malocclusions, to a satisfactory level, and thereby may disabuse clinicians of the belief that only minor malocclusions can be treated with lingual appliances.

  8. Electricity: wastage threatens the climate

    International Nuclear Information System (INIS)

    2009-02-01

    This document proposes a synthesis of a study which aimed at assessing the French energy model, and more particularly its efficiency in the electric power sector, in order to assess the quality and weaknesses of the new guidelines of the French energy policy. By analysing the scenario proposed by public authorities and also by comparing it with a new assessment (trends for global energy consumption and per sector) the authors state that France will not be able to meet its objectives regarding energy and climate. They outline that electricity and transports are the biggest energy consumers, and that, therefore, households should invest in new and more efficient appliances, and in housing insulation. They finally show that an over-consumption of electricity results in higher levels of CO 2 emissions, and criticise the use of electricity for heating, and therefore the development of nuclear energy

  9. Class II malocclusion with complex problems treated with a novel combination of lingual orthodontic appliances and lingual arches.

    Science.gov (United States)

    Yanagita, Takeshi; Nakamura, Masahiro; Kawanabe, Noriaki; Yamashiro, Takashi

    2014-07-01

    This case report describes a novel method of combining lingual appliances and lingual arches to control horizontal problems. The patient, who was 25 years of age at her first visit to our hospital with a chief complaint of crooked anterior teeth, was diagnosed with skeletal Class II and Angle Class II malocclusion with anterior deep bite, lateral open bite, premolar crossbite, and severe crowding in both arches. She was treated with premolar extractions and temporary anchorage devices. Conventionally, it is ideal to use labial brackets simultaneously with appliances, such as a lingual arch, a quad-helix, or a rapid expansion appliance, in patients with complex problems requiring horizontal, anteroposterior, and vertical control; however, this patient strongly requested orthodontic treatment with lingual appliances. A limitation of lingual appliances is that they cannot be used with other conventional appliances. In this report, we present the successful orthodontic treatment of a complex problem using modified lingual appliances that enabled combined use of a conventional lingual arch. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  10. Evaluation of dental plaque control in patients wearing fixed orthodontic appliances: a clinical study.

    Science.gov (United States)

    Ousehal, Lahcen; Lazrak, Laila; Es-Said, Rabia; Hamdoune, Hind; Elquars, Farid; Khadija, Amine

    2011-03-01

    Multibracket orthodontic appliances increase dental plaque retention and make teethbrushing more difficult for patients. As a result, advice from the orthodontist on oral hygiene along with patient motivation regarding teethbrushing are particularly important. The aim of this study was to compare the efficacy of electric toothbrushes with that of manual brushing associated with mouth-rinses comprising chlorhexidine (0.12%) and 0% alcohol. To this end, 84 patients receiving current orthodontic treatment were randomly selected from patients treated at the Dento-Facial Orthopedics department in the Casablanca Dental Consultation and Treatment Center. Selected patients were divided into three groups: Group 1: manual teethbrushing; Group 2: electric teethbrushing; Group 3: manual brushing combined with mouth rinse. Oral hygiene was assessed using the Loe-Silness plaque and gingival indices. Measurements were made before and 4 weeks after the observation period. Results were subjected to statistical comparison in order to determine the group showing greatest improvement and to deduce the best means of controlling bacterial plaque. The electric toothbrush and the chlorhexidine mouth rinse appear to control dental plaque more effectively than manual teethbrushing alone. Following this study, patients receiving multibracket treatment were invited to combine manual brushing with short clinical mouth-rinsing sessions or to use an electric toothbrush. Copyright © 2011 CEO. Published by Elsevier Masson SAS. All rights reserved.

  11. A randomized clinical trial of a new orthodontic appliance to improve upper airway obstruction in infants with Pierre Robin sequence.

    Science.gov (United States)

    Buchenau, Wolfgang; Urschitz, Michael S; Sautermeister, Judit; Bacher, Margit; Herberts, Tina; Arand, Joerg; Poets, Christian F

    2007-08-01

    To test the hypothesis that a new orthodontic appliance with a velar extension that shifts the tongue anteriorly would reduce upper airway obstruction in infants with Pierre Robin sequence (PRS). Eleven infants with PRS (median age, 3 days) and an apnea index (AI) >3 were studied. The effect of the new appliance on the AI was compared with that of a conventional appliance without a velar extension by using a crossover study design with random allocation. Compared with baseline (mean AI, 13.8), there was a significant decrease in the AI with the new appliance (3.9; P value appliance (14.8; P = .842). Thus, the relative change in AI was -71% (95% CI, -84--49) for the new appliance and +8% (95% CI, -52-142) for the conventional appliance, which was significantly different (P = .004). No severe adverse effects were observed. This new orthodontic appliance appears to be safe and effective in reducing upper airway obstruction in infants with PRS.

  12. Comparison of External Apical Root Resorption after Orthodontic Treatment with Two Appliances (Standard Edgewise and MBT

    Directory of Open Access Journals (Sweden)

    V. Mollabashi

    2016-01-01

    Full Text Available Introduction & Objective: The aim of this study was todeterminetheamount of external apical root resorption(EARRwithin two orthodontic appliances (standard edgewise and MBT. Material & Methods In this retrospective study, panoramic radiographs of 83 orthodontic patients (27 male and 56 female were evaluated. 46 patients had been treated with standard edgewise appliance (29 patients with extraction and 17 patients without extraction and 37 patients had been treated with MBT appliance (27 patients with extraction and 10 patients without extraction.EARR were evaluated in 24 teeth (anterior teeth, premolars and first molars in each patient. SPSS software and ordinal regression test were used for statistical analysis. Result: In this study the most EARR was seen in upper lateral incisors, then lower lateral incisors.EARR in upper canines and lower second premolars was significantly related to extraction of first premolarin MBT appliance. In non extraction cases, EARR was not related to the orthodontic appliance. Conclusion: Incisors teeth are the most disposed teeth to EARR. Orthodontic treatment with extraction increased EARR in canines and second premolars. MBT appliance may increase EARR. Sci J Hamadan Univ Med Sci . 2016; 22 (4 :316-322

  13. Application to refrigerator plastics by mechanical recycling from polypropylene in waste-appliances

    International Nuclear Information System (INIS)

    Ha, Kyung Ho; Kim, Moon Saeng

    2012-01-01

    Highlights: → Polypropylene is mechanically recycled from waste-appliances. → Recycled polypropylene (RPP) is impact enhanced polypropylene with ethylene-propylene rubber (EPR). → Performance evaluation shows that RPP is applicable to refrigerator plastics. -- Abstract: For the application to refrigerator plastics by mechanical recycling from polypropylene (PP) in waste-appliances, it needs to identify the degradation and heterogeneity of recycled polypropylene (RPP). It is applicable the thermal analysis such as differential scanning calorimetry (DSC), thermo-gravimetric analysis (TGA), spectroscopic analysis such as Fourier Transform Infrared (FTIR) and morphological analysis such as scanning electronic microscope (SEM). The analysis results show that RPP from waste-appliances is the polyethylene (PE) and polypropylene (PP) copolymer enhanced impact property (Impact-PP) and it is possible to apply refrigerator plastics with good impact property at low temperature. Finally, the performance evaluation of RPP is estimated by Gel Permeation Chromatography (GPC) analysis and is performed by the various mechanical and physical testing methods. It shows that RPP has relatively high molecular weight and balanced properties with strength and toughness. It is expected that RPP by the mechanical recycling from waste-appliances will have about 50% cost-merit.

  14. Custom Made Pressure Appliance for Presurgical Sustained ...

    African Journals Online (AJOL)

    was done to match the color of the appliance with that of the adjoining skin to make ... of the surface of the swelling with the gap between the two ... Figure 1: Preoperative view of keloid .... “multi model” approach for treating ear keloids. Indian J ...

  15. Impact of metal and ceramic fixed orthodontic appliances on judgments of beauty and other face-related attributes.

    Science.gov (United States)

    Fonseca, Lílian Martins; Araújo, Telma Martins de; Santos, Aline Rôde; Faber, Jorge

    2014-02-01

    Physical attributes, behavior, and personal ornaments exert a direct influence on how a person's beauty and personality are judged. The aim of this study was to investigate how people who wear a fixed orthodontic appliance see themselves and are seen by others in social settings. A total of 60 adults evaluated their own smiling faces in 3 different scenarios: without a fixed orthodontic appliance, wearing a metal fixed orthodontic appliance, and wearing an esthetic fixed orthodontic appliance. Furthermore, 15 adult raters randomly assessed the same faces in standardized front-view facial photographs. Both the subjects and the raters answered a questionnaire in which they evaluated criteria on a numbered scale ranging from 0 to 10. The models judged their own beauty, and the raters assigned scores to beauty, age, intelligence, ridiculousness, extroversion, and success. The self-evaluations showed decreased beauty scores (P <0.0001) when a fixed orthodontic appliance, especially a metal one, was being worn. There was no statistically significant difference between the 3 situations in the 6 criteria analyzed. A fixed orthodontic appliance did not affect how personal attributes are assessed. However, fixed orthodontic appliances apparently changed the subjects' self-perceptions when they looked in the mirror. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  16. Alteration in Taste Perception among Young Children during the use of Removable Orthodontic Appliance Therapy.

    Science.gov (United States)

    Razdan, Priyanka; Sakthivel, V S; Naqvi, Zuber A; Goyal, Vinod; Tripathi, Swati; Singh, Smita

    2017-07-01

    The sense of smell is very influential in the taste of foods. If the smell pleases us, we anticipate the taste of the food with a great deal of relish. If our sense of smell is impaired, so is our taste. The effect of appliance on taste perceptions has always had a controversial subject. The present study was designed to analyze the change in taste perception in children using removable orthodontic appliances. All the selected volunteers were given different taste stimuli and were asked to score as per their perception. The verbal score was calculated based on the correct and incorrect taste stimuli given to them. Visual analog scale was used to assess intensity and hedonic (palatability) estimation of the volunteers. The volunteers from both study and control groups scored different values for taste stimuli. The majority of stimuli were estimated correctly by both groups. There was no statistically significant difference between the study and control groups. In different testing sessions, the scoring of the volunteers was nearly constant, indicating that an appliance does not play a major role in the alteration of taste stimuli. The appliance brings about transient change in taste perception, we should educate the patient before delivering the appliance about the transient change in taste perception and encourage full-time wear of the appliance, including during meals, without fear of affecting taste sensations.

  17. Randomized, double-blind, placebo-controlled trial to test the efficacy of nitradine tablets in maxillary removable orthodontic appliance patients.

    Science.gov (United States)

    Vento-Zahra, Ethel; De Wever, Bart; Decelis, Stephen; Mallia, Kenneth; Camilleri, Simon

    2011-01-01

    to evaluate the efficiency of NitrAdine (MSI Laboratories) tablets in the reduction of oral Candida levels, biofilm formation, and appliance odor in maxillary removable orthodontic appliance wearers. seventy children between 11 and 15 years of age undergoing maxillary removable appliance treatment were assigned via a double-blind randomized method to the experimental or placebo arm of the study. One milliliter of unstimulated saliva was collected at the beginning of the experiment and 6 weeks later after treatment of the maxillary removable appliance with NitrAdine tablets. Samples were cultured on chromogenic Candida agar, and the number of colony-forming units per mL of saliva (CFU mL-1) was determined. there was no significant difference in salivary Candida levels before or after treatment with NitrAdine tablets. There was a significant drop in plaque accumulation on the appliance and a significant amelioration in appliance odor. There was a small, nonsignificant drop in individuals exhibiting counts of 400 CFU mL-1 or more in the experimental group and a nonsignificant increase in the number of new species in the placebo group. NitrAdine tablets are effective in reducing plaque accumulation and appliance odor during maxillary removable appliance treatment. Further in vivo studies are required to determine the efficacy and exact protocol for NitrAdine tablets in appliance disinfection.

  18. Pendulum and modified pendulum appliances for maxillary molar distalization in Class II malocclusion - a systematic review.

    Science.gov (United States)

    Al-Thomali, Yousef; Basha, Sakeenabi; Mohamed, Roshan Noor

    2017-08-01

    The main purpose of the present systematic review was to evaluate the quantitative effects of the pendulum appliance and modified pendulum appliances for maxillary molar distalization in Class II malocclusion. Our systematic search included MEDLINE, EMBASE, CINAHL, PsychINFO, Scopus and key journals and review articles; the date of the last search was 30 January 2017. We graded the methodological quality of the studies by means of the Quality Assessment Tool for Quantitative Studies, developed for the Effective Public Health Practice Project (EPHPP). In total, 203 studies were identified for screening, and 25 studies were eligible. The quality assessment rated four (16%) of the study as being of strong quality and 21 (84%) of these studies as being of moderate quality. The pendulum appliances showed mean molar distalization of 2-6.4 mm, distal tipping of molars from 6.67° to 14.50° and anchorage loss with mean premolar and incisor mesial movement of 1.63-3.6 mm and 0.9-6.5 mm, respectively. The bone anchored pendulum appliances (BAPAs) showed mean molar distalization of 4.8-6.4 mm, distal tipping of molars from 9° to 11.3° and mean premolar distalization of 2.7-5.4 mm. Pendulum and modified pendulum appliances are effective in molar distalization. Pendulum appliance with K-loop modification, implant supported pendulum appliance and BAPA significantly reduced anchorage loss of the anterior teeth and distal tipping of the molar teeth.

  19. Factors affecting dental biofilm in patients wearing fixed orthodontic appliances.

    Science.gov (United States)

    Mei, Li; Chieng, Joyce; Wong, Connie; Benic, Gareth; Farella, Mauro

    2017-12-01

    The aim of this study is to investigate the amount and the distribution of biofilm in patients wearing fixed appliances and its relation with age, gender, frequency of tooth brushing, and patient motivation. The sample comprised 52 patients (15.5 ± 3.6 years old, 30 females and 22 males) wearing fixed orthodontic appliances. Dental biofilm was assessed using a modified plaque index (PI). A questionnaire was used to collect patient's information, including gender, age, treatment motivation, and frequency of tooth brushing. Gingival (PI score = 0.9 ± 0.7), mesial (0.8 ± 0.6), and distal (0.8 ± 0.5) areas accumulated more biofilm than occlusal areas (0.3 ± 0.3) (P appliances have the highest biofilm accumulation on the maxillary lateral incisors and maxillary canines, particularly in the gingival area and areas behind arch wires. Less biofilm was observed in female and adult patients and in those who were self-motivated and brushed their teeth more often.

  20. Technical Appliance in E-Learning: Student’s Perception on the Usage of Online Learning

    Directory of Open Access Journals (Sweden)

    Siti Sarah Mohd Johari

    2010-06-01

    Full Text Available The purpose of this study is to gain insights into student’s perception on the usage of technical appliances on online learning. The study took place in the Universiti Sains Malaysia (USM based on the sample of 1084 student s with the experiences of using E-learning Portal as one of the distance education academic programme. The students were surveyed on the participation needs based on respondent’s personal background, such as age, gender, ethnic groups, education streams and year-of-study. Results of the study showed even though most of the students felt uncertain about the technical appliances in E-learning Portal, the study illustrates the true nature of the student’s perceptions with respect to the functionality and effectiveness of technical appliance in E-learning Portal. This research is essential to elucidate the functions of technical appliances in facilitating the process of learning through the portal.

  1. The effects of customer benefit and regulation on environmental product innovation. Empirical evidence from appliance manufacturers in Germany

    International Nuclear Information System (INIS)

    Kammerer, Daniel

    2009-01-01

    Environmental product (EP) innovations and their determinants have received increasing attention from researchers during the past years. So far, empirical studies have shown inconsistent results, especially regarding the impact of regulation. In this paper, I seek to advance the understanding of EP-innovation by introducing and testing a novel research framework. First, a novel unit of analysis, the environmental issue level, is applied. EP-innovation is not studied in broad terms but specifically for four environmental issues that are relevant to the electrical and electronic appliances industry: energy efficiency, toxic substances, material efficiency, and electromagnetic fields. Second, the customer benefit, a concept from the green marketing literature, is included as an explanatory variable for EP-innovation for the first time. The argument is that green products which besides their public benefits have private environmental benefits for the customer (e.g., energy savings) will generate stronger consumer demand and can thus constitute the firm's motivation to implement those innovations in the first place. Third, EP-innovation is observed more comprehensively, measuring its extent and level of novelty. I apply this research framework to study EP-innovations of German manufacturers of electrical and electronic appliances. My results support the issue level as unit of analysis. The impact of customer benefit and regulation on EP-innovation is analyzed with logit regression and the results clearly show that both customer benefit and regulation play a key role for EP-innovation. They not only foster the implementation of EP-innovations but also their broad application and their level of novelty. (author)

  2. 46 CFR 160.031-4 - Equipment for shoulder gun type line-throwing appliance.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 6 2010-10-01 2010-10-01 false Equipment for shoulder gun type line-throwing appliance... Appliance, Shoulder Gun Type (and Equipment) § 160.031-4 Equipment for shoulder gun type line-throwing... the gun. The line canister shall be secured by clamps or brackets below the barrel of the gun. (c) One...

  3. Scheduling home-appliances to optimize energy consumption

    DEFF Research Database (Denmark)

    Rossello Busquet, Ana

    In order to optimize the energy consumption, energy demand peaks should be avoided, and energy consumption should be smoothly distributed over time. This can be achieved by setting a maximum energy consumption per user’s household. In other words, the overall consumption of the user’s appliances...

  4. Evaluation of Musculoskeletal Disorders in Household Appliances Manufacturing Company

    Directory of Open Access Journals (Sweden)

    Aioob Ghanbary

    2015-12-01

    Full Text Available Work-related musculoskeletal disorders are the most prevalent work-related disorders and injuries and being the main cause of disability. This study was conducted to assessment of the prevalence of musculoskeletal disorders in worker company household appliances production. Posture analysis was evaluated by OWAS method and prevalence of musculoskeletal disorders by Nordic questionnaire. With evaluating musculoskeletal disorders among company household appliances production can intervention action to reduce musculoskeletal disorders was carried out. This cross-sectional study was performed on 100 workers of the appliance manufacturing industry. These Individuals were included 15 persons from foam injection workshop, 17 persons from molding workshop, 17 operators of presses, 17 persons from packaging, 17 person from cutting unit and 17 operators of rivet. The Nordic questionnaire was completed by Individuals for the organs of arm, back, leg and wrist and Posture analysis was performed by OWAS method. The data were analyzed using Spss software version 18 and descriptive statistics and Anova test. Nordic questionnaire results revealed that highest disorders were observed in the arm (25%, back (22% and leg (21%. Also Anova test showed that was observed a significant correlation respectively between age and work experience with the prevalence of musculoskeletal disorders (p<0.02 (p<0.01. The results showed based on the level of risk OWAS for each job respectively, the highest level of risk associated with foam injection unit, packaging and cutting unit (risk level 4 and the lowest level of risk associated with molding workshop unit (risk level 2.The results of this study showed that household appliances Manufacturing workers due to the nature of their jobs are at risk of musculoskeletal disorders and Ergonomic interventions to do such as workstation redesign, reduced working hours, cycle of rest-work development.

  5. Greening production and consumption: the case of the appliance and dairy industries in Thailand

    NARCIS (Netherlands)

    Thongplew, N.

    2015-01-01

    Abstract

    Natapol Thongplew

    Thesis title: Greening production and consumption: The case of the appliance and dairy industries in Thailand

    This research looked into the greening of the appliance and dairy industries in

  6. Effect of dental wear, stabilization appliance and anterior tooth reconstruction on mandibular movements during speech.

    Science.gov (United States)

    Serrano, Priscila de Oliveira; Faot, Fernanda; Del Bel Cury, Altair Antoninha; Rodrigues Garcia, Renata Cunha Matheus

    2008-01-01

    This study described changes in mandibular movements during pronunciation of /m/ and /s/ sounds in Portuguese, in patients presenting dental wear before and after appliance insertion and tooth reconstruction. Subjects were divided into a control group of dentate patients and an experimental group of patients with incisal tooth wear due to bruxism. A magnetic jaw tracking device measured the jaw opening, and translations to left and right sides of the mandible during pronunciation of phonemes. Evaluations were carried out 1 week and immediately before appliance insertion; 24 h, 7, 30 and 60 days after appliance insertion; and 1 week and 1 month after tooth reconstruction. Data were submitted to two-way ANOVA, Mann-Whitney and Friedman tests (pspeech of /m/ and /s/ sounds were not changed after appliance insertion and reconstruction of teeth.

  7. Meta-analysis of skeletal mandibular changes during Frankel appliance treatment.

    Science.gov (United States)

    Perillo, Letizia; Cannavale, Rosangela; Ferro, Fabrizia; Franchi, Lorenzo; Masucci, Caterina; Chiodini, Paolo; Baccetti, Tiziano

    2011-02-01

    The purpose of this study was to perform a meta-analysis of articles to verify the mandibular changes produced by the Fränkel-2 (FR-2) appliance during the treatment of growing patients with Class II malocclusions when compared with untreated growing Class II subjects. The literature published from January 1966 to January 2009 was reviewed with search engines. A quality analysis was performed. The effects on primary end points were calculated with random-effect models. Heterogeneity was assessed using Q statistic and investigated using study-level meta-regression. A total of nine articles were identified. The quality of the studies ranged from low to medium. Meta-analysis showed that the FR-2 was associated with enhancement of mandibular body length [0.4 mm/year 95 per cent confidence interval (CI) 0.182-0.618], total mandibular length (1.069 mm/year, 95 per cent CI 0.683-1.455), and mandibular ramus height (0.654 mm/year, 95 per cent CI 0.244-1.064). A consistent heterogeneity among studies was found for all the considered linear measurements. The FR-2 appliance had a statistically significant effect on mandibular growth. Nevertheless, the heterogeneity of the FR-2 effects, the quality of studies, the differences in age, skeletal age, treatment duration, and the inconsistent initial diagnosis seem to overstate the benefits of the FR-2 appliance. An evidence-based approach to the orthodontic outcomes of FR-2 appliance is needed, by selecting and comparing groups of children with the same cephalometric characteristics with and without treatment.

  8. Agent-based model for electricity consumption and storage to evaluate economic viability of tariff arbitrage for residential sector demand response

    International Nuclear Information System (INIS)

    Zheng, Menglian; Meinrenken, Christoph J.; Lackner, Klaus S.

    2014-01-01

    Highlights: • Storage-based demand response (loadshifting) is underutilized in residential sector. • Economics (arbitrage savings versus equipment cost) are not well understood. • Stochastic demand models and real-life tariffs can illuminate economic viability. • A range of available storage options provide economically viable DR. • Daily/seasonal stochastic demand variations crucial to understanding optimum capacity. - Abstract: Demand response (DR) is one of many approaches to address temporal mismatches in demand and supply of grid electricity. More common in the commercial sector, DR usually refers to reducing consumption at certain hours or seasons, thus reducing peak demand from the grid. In the residential sector, where sophisticated appliance-level controls such as automatic dimming of lights or on-demand lowering of air conditioning are less common, building-based electricity storage to shift grid consumption from peak to off-peak times could provide DR without requiring consumers to operate their appliances on shifted or reduced schedules: Storage would be dispatched to appliances as needed while still shaving peaks on the grid. Technologically, storage and two-way-inverters are readily available to enable such residential DR. Economically, however, the situation is less clear. Specifically, are time-varying electricity tariffs available such that electricity cost reduction via arbitrage could offset manufacturing, financing, and installation costs of the required storage? To address this question we (i) devise an agent-based appliance-level stochastic model to simulate the electricity demand of an average U.S. household; (ii) loadshift the demand via simple dispatch strategies; and (iii) determine potential profits to the building owner, i.e. reduced electricity cost of the modified demand with realistic tariffs (Con Edison, NY) minus storage cost. We determine the economic viability for a range of traditional and advanced storage technologies

  9. 40 CFR Appendix C to Subpart F of... - Method for Testing Recovery Devices for Use With Small Appliances

    Science.gov (United States)

    2010-07-01

    ... for Use With Small Appliances C Appendix C to Subpart F of Part 82 Protection of Environment... Recovery Devices for Use With Small Appliances Recovery Efficiency Test Procedure for Refrigerant Recovery Equipment Used on Small Appliances The following test procedure is utilized to evaluate the efficiency of...

  10. A long- and short-run analysis of electricity demand in Ciudad Juarez

    Science.gov (United States)

    Mendez-Carrillo, Ericka Cecilia

    Economic growth and appliance saturation are increasing electricity consumption in Mexico. Annual frequency data from 1990 to 2012 are utilized to develop an error correction framework that sheds light on short- and long-run electricity consumption behavior in Ciudad Juarez, a large Mexican metropolitan economy at the border with the United States. The results for this study reveal that electricity is an inelastic normal good in this market. Moreover, natural gas is found to be a weak complement to electricity. With regards to the customer base in this urban economy, population, employment, and income exercise positive and statistically significant impacts on the demand for electricity hook-ups.

  11. Electricity's effect on gender equality in rural Zanzibar, Tanzania : case study for Gender and Energy World Development Report Background Paper

    NARCIS (Netherlands)

    Winther, Tanja

    2012-01-01

    This anthropological case study on the introduction of electricity in rural Zanzibar around 1990 discusses to what extent and how women became empowered in the process. What factors contributed to increased gender equality during the uptake of electricity and related appliances – and what were the

  12. Device for inserting and removing electric plug in socket- using remote handling apparatus inside radioactive hot cell

    International Nuclear Information System (INIS)

    Chevallereau, R.; Galmard, Y.

    1994-01-01

    A device for pushing an electric plug into a supply socket inside a radioactive hot cell and for withdrawing the plug after use of the appliance attached to it, comprises a pair of pivotally mounted arms. It can be used inside radioactive hot cells, to insert and put in and put off electric plugs

  13. Mandibular advancement appliance for obstructive sleep apnoea

    DEFF Research Database (Denmark)

    Petri, Niels; Svanholt, Palle; Solow, Beni

    2008-01-01

    The aim of this trial was to evaluate the efficacy of a mandibular advancement appliance (MAA) for obstructive sleep apnoea (OSA). Ninety-three patients with OSA and a mean apnoea-hypopnoea index (AHI) of 34.7 were centrally randomised into three, parallel groups: (a) MAA; (b) mandibular non...

  14. The International Database of Efficient Appliances (IDEA): A New Resource for Global Efficiency Policy

    Energy Technology Data Exchange (ETDEWEB)

    Gerke, Brian F; McNeil, Michael A; Tu, Thomas; Xu, Feiyang

    2017-09-06

    A major barrier to effective appliance efficiency program design and evaluation is a lack of data for determination of market baselines and cost-effective energy savings potential. The data gap is particularly acute in developing countries, which may have the greatest savings potential per unit GDP. To address this need, we are developing the International Database of Efficient Appliances (IDEA), which automatically compiles data from a wide variety of online sources to create a unified repository of information on efficiency, price, and features for a wide range of energy-consuming products across global markets. This paper summarizes the database framework and demonstrates the power of IDEA as a resource for appliance efficiency research and policy development. Using IDEA data for refrigerators in China and India, we develop robust cost-effectiveness indicators that allow rapid determination of savings potential within each market, as well as comparison of that potential across markets and appliance types. We discuss implications for future energy efficiency policy development.

  15. Flexible demand in the GB domestic electricity sector in 2030

    International Nuclear Information System (INIS)

    Drysdale, Brian; Wu, Jianzhong; Jenkins, Nick

    2015-01-01

    Highlights: • Annual domestic demand by category and daily flexible load profiles are shown to 2030. • Valuable flexible demand requires loads to be identifiable, accessible, and useful. • The extent of flexible demand varies significantly on a diurnal and seasonal basis. • Barriers to accessing domestic demand include multiple low value loads and apathy. • Existing market structure a barrier to fully rewarding individual load flexibility. - Abstract: In order to meet greenhouse gas emissions targets the Great Britain (GB) future electricity supply will include a higher fraction of non-dispatchable generation, increasing opportunities for demand side management to maintain a supply/demand balance. This paper examines the extent of flexible domestic demand (FDD) in GB, its usefulness in system balancing and appropriate incentives to encourage consumers to participate. FDD, classified as electric space and water heating (ESWH), and cold and wet appliances, amounts to 59 TW h in 2012 (113 TW h total domestic demand) and is calculated to increase to 67 TW h in 2030. Summer and winter daily load profiles for flexible loads show significant seasonal and diurnal variations in the total flexible load and between load categories. Low levels of reflective consumer engagement with electricity consumption and a resistance to automation present barriers to effective access to FDD. A value of £1.97/household/year has been calculated for cold appliance loads used for frequency response in 2030, using 2013 market rates. The introduction of smart meters in GB by 2020 will allow access to FDD for system balancing. The low commercial value of individual domestic loads increases the attractiveness of non-financial incentives to fully exploit FDD. It was shown that appliance loads have different characteristics which can contribute to an efficient power system in different ways

  16. ASSESSMENT OF THE ELECTRIC POWER QUALITY ON THE POLISH FISHING BOATS

    Directory of Open Access Journals (Sweden)

    Dariusz TARNAPOWICZ

    2015-07-01

    Full Text Available Power quality is an important problem for electrical systems. Electricity receivers should operate at nominal conditions. Each deviation from nominal values may cause the malfunction of electrical devices, decreasing their durability and per-manently damage the appliance. The importance of electric power quality for technical systems and individual electrical devices on fishing boats is fundamental. Utilization of equipment powered by electrical energy with a reduced quality resulting in economical losses and the treat to the screw's safety. Researches of the electrical energy's quality were carried out almost any type of fishing boats. This article presents the results of researches concerning the quality of electrical energy performed on a representative type of fishing boats. It shortly evaluates the results of tests and suggests solutions to improve the power quality parameters.

  17. Clinical Effectiveness of Using Aesthetic Fixed Prosthetic Appliances with Combined Occlusal Surface

    Directory of Open Access Journals (Sweden)

    Andrii Biben

    2017-06-01

    Conclusions. Aesthetic fixed prosthetic appliances with combined occlusal surface demonstrated high functional and aesthetic characteristics. The use of the USHPS system showed a decisive advantage of milled frameworks and combined occlusal surface over traditional cast ceramic frameworks.The combination of high mechanical, strength and tribological properties of zirconium dioxide and high biological as well as aesthetic properties of ceramic materials helped reveal high clinical characteristics of aesthetic appliances with combined occlusal surface.

  18. Gas at work. Vision on decentralized gas appliances in the built environment

    International Nuclear Information System (INIS)

    Van Gastel, M.; Hooijschuur, J.; De Jong, A.; De Visser, I.; Overdiep, H.; Bakker, E.J.; Van Wolferen, H.

    2008-04-01

    Various platforms operate within the SenterNovem programme Creative Energy. This report is the first version of the vision document of the working group Decentralized gas appliances of the Platform New Gas, in which the following aspects of the various promising innovative gas appliances are indicated: the development stage, the intended energy saving, the CO2 reduction, the bottlenecks for large scale market introduction and the solutions for these bottlenecks. [mk] [nl

  19. Assessment of the rate of premolar extraction space closure in the maxillary arch with the AcceleDent Aura appliance vs no appliance in adolescents: A single-blind randomized clinical trial.

    Science.gov (United States)

    Miles, Peter; Fisher, Elizabeth; Pandis, Nikolaos

    2018-01-01

    The purpose of this 2-arm parallel trial was to assess the effect of the AcceleDent Aura appliance (OrthoAccel Technologies, Houston, Tex) on the rate of maxillary premolar extraction space closure in adolescent patients. Forty Class II adolescents treated with full fixed appliances and maxillary premolar extractions participated in this randomized clinical trial. They were recruited in a private practice and treated by 1 clinician. Randomization was accomplished in blocks of 10 patients assigned to either a no-appliance group or the AcceleDent Aura appliance group with the allocations concealed in opaque, sealed envelopes. Both the operator and the outcome assessor were blinded; however, it was not feasible to blind the patients. Models were taken of the maxillary arch at the start of space closure and just before complete space closure. The space was measured parallel to the occlusal plane from the cusp tips of the teeth mesial and distal to the extraction spaces. There was no clinically (0.05 mm per month; 95% confidence interval [CI], -0.24, 0.34) or statistically significant difference in the rate of space closure (P = 0.74). In both the univariable and multivariable analyses, the mean rate of tooth movement was slower by 0.13 mm per month (95% CI, -.26, .005) on the left side compared with the right side, but this was not statistically significant (P = 0.06). The AcceleDent Aura appliance had no effect on the rate of maxillary premolar extraction space closure. Only a few participants were considered to be good compliers with the appliance. However, the rate of space closure in the good compliers was similar to the overall group and did not appear to influence the result. This trial was not registered. The protocol was not published before trial commencement. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  20. Interceptive Correction of Anterior Crossbite Using Short-Span Wire-Fixed Orthodontic Appliance: A Report of Three Cases

    Directory of Open Access Journals (Sweden)

    S. Nagarajan M. P. Sockalingam

    2018-01-01

    Full Text Available Anterior crossbite is relatively a common presentation in the mixed dentition stage. If left untreated, it can lead to a host of problems and may complicate future orthodontic treatment. One of the major difficulties in performing anterior crossbite correction in young children is treatment compliance. In most cases, poor compliance is due to the unacceptability of the removable appliance used. This article describes three cases of successful correction of anterior crossbite of patients in mixed dentition using short-span wire-fixed orthodontic appliances. This sectional appliance provides an alternative method of correcting anterior crossbite of dental origin and offers many advantages compared to the use of removable appliances.

  1. Esthetic perception and economic value of orthodontic appliances by lay Brazilian adults

    Directory of Open Access Journals (Sweden)

    Daniela Feu

    2012-10-01

    Full Text Available OBJECTIVE: To evaluate the esthetic perception of different appliances by Brazilian lay adults and its influence in the attributed value of orthodontic treatment, considering evaluators' socioeconomic status, age and gender. METHODS: Eight different combinations of orthodontic appliances and clear tray aligners were placed in a consenting adult with pleasing smile. Standardized frontal photographs were captured and incorporated into a research album. A sample of adults (n = 252, median = 26 years old were asked to rate each image for (1 its attractiveness on a visual analog scale and (2 the willingness to pay (WTP for a cosmetic appliance when compared to a standard metalic appliance and a clear tray aligner. Comparisons between the appliances' attractiveness were performed using the Friedman's test and Dann's post-hoc test. Correlation between appliances' attributed value, socioeconomic status, age, gender, and esthetic perception was assessed using Spearman's correlation analysis. RESULTS: Attractiveness ratings of orthodontic appliances varied significantly in the following hierarchy: Clear aligners>sapphire brackets>self-ligating/conventional stainless steel brackets>and golden metal appliances. The correlation between WTP and esthetic perception was week. However, for individuals with better socioeconomic status and aged between 17-26 years old significantly, a significantly higher WTP was found. CONCLUSION: Clear aligners and sapphire brackets with esthetic archwire were considered better esthetic options in this sample. Nevertheless, patients were not willing to pay more money for appliances they deemed more esthetic, however, they were significantly influenced by their socioeconomic level and age.OBJETIVO: avaliar a percepção de brasileiros adultos leigos para diferentes aparelhos ortodônticos e sua influência na valorização econômica do tratamento, considerando o nível socioeconômico, idade e sexo dos avaliadores. M

  2. Adolescents and electricity consumption; Investigating sociodemographic, economic, and behavioural influences on electricity consumption in households

    International Nuclear Information System (INIS)

    Wallis, Hannah; Nachreiner, Malte; Matthies, Ellen

    2016-01-01

    With respect to changes in the energy systems of many countries, electricity consumption in households is an important topic. Extensive research has investigated the various determinants of electricity consumption. However, insights into how specific sociodemographic, behavioural, and attitudinal determinants influence residential electricity consumption are still scarce. In this study, we used hierarchical regression analysis to systematically investigate these determinants (including household engagement in electricity saving) along with a wide range of other measures in a sample of German households (N=763). Special attention was given to households with adolescents and children by analysing the influence of the number of adolescents on electricity consumption in a path model. Our results indicate that sociodemographic influences can be explained by the purchasing and use behaviours of residents. Our findings also suggest that the use of behavioural information provides a more detailed picture of the conditions of electricity consumption and thus allows for more appropriate policy planning. - Highlights: •We examined causal drivers of sociodemographic influences on electricity consumption •Sociodemographic influences can be explained by behaviour •Influence of adolescents is mediated by their purchases of IT appliances •It is necessary to also use behavioural information for policy planning

  3. Electricity use and load management in electricity heated one-family houses from customer and utility perspective; Effekten av effekten - Elanvaendning och laststyrning i elvaermda smaahus ur kund- och foeretagsperspektiv

    Energy Technology Data Exchange (ETDEWEB)

    Sernhed, Kerstin

    2004-11-01

    Until recently, the increase in electricity demand and peak power demand has been met by expansion of the electricity production. Today, due to the deregulation of the electricity market, the production capacity is decreasing. Therefore, there is a national interest in finding solutions to peak problems also on the demand side. In the studies described here (Study 1 and 2) ten households in electrically heated houses were examined. In 1999 the utility equipped their customers with a remote metering system (CustCom) that has an in-built load control component. In Study 1, the load pattern of ten households was examined by using energy diaries combined with frequent meter readings (every five minutes) of the load demand for heating, hot water service and domestic electricity use. Household members kept energy diaries over a four-day period in January 2004, noting time, activities and the use of household appliances that run on electricity. The analysis showed that the use of heat-producing household appliances, e.g. sauna, washing machine and dryer, appliances used for cooking, dishwasher and extra electric heaters, contribute to the household's highest peaks. Turning on the sauna and at the same time using the shower equates to a peak load of 7-9 kW. This, in addition to the use of electricity for heating and lighting along alongside electricity use for refrigerators and freezers, results in some households reaching their main fuse level (roughly 13,8 kW for a main fuse of 20 A). This means that the domestic use of electricity makes up a considerable part of the highest peak loads in a household, but the highest peaks occur together with the use of electricity for heating and hot water. In the second study, Study 2, the households participated in a load control experiment, in which the utility was able to turn on and switch off the heating and hot water systems remotely, using the CustCom system. Heating and water heaters were switched off for periods of 1

  4. Evaluation of temporomandibular disorders in Class III patients treated with mandibular cervical headgear and fixed appliances.

    Science.gov (United States)

    Rey, Diego; Oberti, Giovanni; Baccetti, Tiziano

    2008-03-01

    Our aim in this study was to evaluate the prevalence of temporomandibular disorders (TMD) in Class III patients treated with mandibular cervical headgear (MCH) and fixed appliances. The sample of 75 patients included 25 patients with no previous orthodontic treatment, 25 Class I patients who had undergone orthodontic treatment with fixed appliances and without extractions, and 25 patients with dentoskeletal Class III disharmonies treated with MCH and fixed appliances. The Helkimo index was used to test the prevalence of TMD symptoms in the 3 groups. The prevalence rates of the Helkimo index in the 3 groups were compared with the z score on proportions. No statistically significant differences in the prevalence rates of the Helkimo index scores in the 3 groups were found (P = .367). Most subjects in the 3 groups had an Helkimo index of zero (66.7%). Subjects with Class III malocclusions treated with MCH and fixed appliances do not have greater prevalence of TMD symptoms than do Class I subjects treated with fixed appliances or untreated subjects.

  5. Dentoalveolar and skeletal changes associated with the pendulum appliance followed by fixed orthodontic treatment.

    Science.gov (United States)

    Angelieri, Fernanda; Almeida, Renato Rodrigues de; Almeida, Marcio Rodrigues de; Fuziy, Acácio

    2006-04-01

    This prospective clinical study analyzed the distalization of maxillary molars achieved by the pendulum appliance and its effect on the anchorage teeth during and after fixed orthodontic treatment. Lateral cephalograms of 22 adolescents (15 girls, 7 boys) taken pretreatment, after distalization, after leveling and aligning, and after fixed orthodontic treatment were evaluated. The initial mean age was 14.5 years (SD = 1.80). The mean time for distalization of the maxillary molars was 5.85 months (SD = 1.82), and the total treatment time was 3.61 years (SD = 1.83). The pendulum appliance moved the maxillary molars distally, but with significant distal inclination, protrusion of the anterior teeth, and increase in lower anterior facial height (LAFH) due to the clockwise mandibular rotation. After fixed orthodontic treatment, the maxillary incisors and the maxillary first premolars and first molars were returned to their pretreatment anteroposterior positions. Thus, at postdistalization, there was 2.1 mm of protrusion of the maxillary first molars, despite the anchorage reinforcement (Nance button and cervical headgear worn at night during fixed appliance therapy). However, at the end of treatment, all patients had Class I molar relationships. The pendulum appliance followed by fixed orthodontic treatment corrected the Class II sagittal relationship, especially due to the dentoalveolar changes secondary to the spontaneous mandibular growth in the anterior direction during fixed appliance treatment.

  6. Hoisting appliances and fuel handling equipment at nuclear facilities

    International Nuclear Information System (INIS)

    1987-01-01

    The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection

  7. Simulation platform for direct load control of household appliances. Literature survey and G2 implementation

    Energy Technology Data Exchange (ETDEWEB)

    Kolm, J; Vlaheli, A

    1996-10-01

    There is an incentive for the power utilities to look for other ways than building new power stations to satisfy increasing customer power needs. One way to fulfill this demand is by redistributing the available electric power between the different power consumers. This method can successfully be used during high peak hours. The utility is also able to make financial profits selling the redistributed electric power at a higher price to customers with temporary high power demands. Direct Load Control - DLC, a Demand Side Management - DSM tool, is one way to achieve a redistribution of electric power. This masters thesis project consisted in developing a user-friendly simulation platform for domestic appliances combined with an electric power control system to be employed for Direct Load Control. The platform contains the necessary facilities for designing an electrical distribution network model and is implemented in G2, an object-oriented real-time environment. The final application provides an on-line instrument for the utility to control the power consumption over the entire system in terms of dispensing power in an electrical network. The report consists of two main parts. The first part describes a literature survey we systematically compiled to gather literature sources. The second part outlines our design and implementation of the G2 simulation platform for a water-heater model with a Direct Load Control system. The entire simulation platform is designed to allow a flexible change and improvement of the different models. Consequently, our software is a powerful tool for studying a wide range of problems related to a Load Management program involving electrical household loads. 9 refs, 32 figs

  8. Cl II Malocclusion Treatment, Using the Modified Twin Block Appliance Coordinated with Fixed Orthodontics in a Postmenarche Patient

    Directory of Open Access Journals (Sweden)

    Amin Aminian

    2017-01-01

    Full Text Available Functional appliances have been used for treatment of Class II patients for a long time. The main objective of therapy with functional appliances is to induce supplementary lengthening of the mandible by stimulating increased growth at the condylar cartilage. The Twin Block appliance is one of the most commonly used functional appliances. The aim of this paper is to present a case report of mandibular deficiency treatment with Twin Block appliance in a female patient whose sexual maturation (one and a half years after menarche and cervical vertebral maturation stage indicated the end of the growth peak. The treatment started with bonding 0.022 in MBT prescription brackets on the upper arch in order to align upper teeth and create a symmetric overjet. When reaching alignment, a modified Twin Block was given to the patient for 8 months. Final coordination was achieved with fixed appliances in both arches. At the end of the treatment, profile of the patient improved, crowding was relieved, and Cl I relationship with normal overjet and overbite was achieved.

  9. Cone beam computed tomography study of apical root resorption induced by Herbst appliance

    Science.gov (United States)

    SCHWARTZ, João Paulo; RAVELI, Taísa Boamorte; ALMEIDA, Kélei Cristina de Mathias; SCHWARTZ-FILHO, Humberto Osvaldo; RAVELI, Dirceu Barnabé

    2015-01-01

    Objective This study evaluated the frequency of root resorption during the orthodontic treatment with Herbst appliance by Cone Beam Computed Tomography (CBCT). Material and Methods The sample comprised 23 patients (11 men, 12 women; mean ages 15.76±1.75 years) with Class II division 1 malocclusion, treated with Herbst appliance. CBCT was obtained before treatment (T0) and after Herbst treatment (T1). All the dental roots, except third molars, were evaluated, and apical root resorption was determined using the axial guided navigation method. Paired t-tests and Wilcoxon T Test were used to compare the dependent samples in parametric and nonparametric cases, respectively. Chi-Square Test with Yates’ correction was used to evaluate the relationship between apical root resorption and gender. Results were considered at a significance level of 5%. Results Apical resorption was detected by CBCT in 57.96% of 980 roots that underwent Herbst appliance treatment. All patients had minimal resorption and there was no statistical significance between the genders. Conclusion CBCT three-dimensional evaluation showed association between Herbst appliance and minimal apical root resorption, mostly in the anchoring teeth, without clinical significance. PMID:26537718

  10. Cone beam computed tomography study of apical root resorption induced by Herbst appliance

    Directory of Open Access Journals (Sweden)

    João Paulo SCHWARTZ

    2015-10-01

    Full Text Available Objective This study evaluated the frequency of root resorption during the orthodontic treatment with Herbst appliance by Cone Beam Computed Tomography (CBCT.Material and Methods The sample comprised 23 patients (11 men, 12 women; mean ages 15.76±1.75 years with Class II division 1 malocclusion, treated with Herbst appliance. CBCT was obtained before treatment (T0 and after Herbst treatment (T1. All the dental roots, except third molars, were evaluated, and apical root resorption was determined using the axial guided navigation method. Paired t-tests and Wilcoxon T Test were used to compare the dependent samples in parametric and nonparametric cases, respectively. Chi-Square Test with Yates’ correction was used to evaluate the relationship between apical root resorption and gender. Results were considered at a significance level of 5%.Results Apical resorption was detected by CBCT in 57.96% of 980 roots that underwent Herbst appliance treatment. All patients had minimal resorption and there was no statistical significance between the genders.Conclusion CBCT three-dimensional evaluation showed association between Herbst appliance and minimal apical root resorption, mostly in the anchoring teeth, without clinical significance.

  11. Effect of fixed orthodontic appliances on salivary microbial parameters at 6 months: a controlled observational study

    Directory of Open Access Journals (Sweden)

    Delphine MARET

    2014-01-01

    Full Text Available Objective: The aim of this study was to assess the microbial changes in children with fixed orthodontic appliances compared with a control group of children without orthodontic treatment. Material and Methods: Ninety-five children, aged between 12 and 16 years, participated in this study. Forty-eight subjects were fitted with fixed orthodontic appliances and forty-seven were free of any such appliances. The follow-up was 6 months for all children. The association between orthodontic appliances and high levels of Streptococcus mutans and Lactobacillus spp was assessed with logistic regression models, taking age, sex, pH and buffer capacity into account. Results: Differences at baseline between the two groups were not statistically significant. We found that wearing a fixed orthodontic appliance was associated with high levels of Streptococcus mutans and Lactobacillus spp (adjusted OR: 6.65, 95% CI [1.98-22.37]; 9.49, 95% CI [2.57-35.07], respectively, independently of other variables. Conclusion: The originality of the present epidemiological study was to evaluate the evolution of salivary microbial parameters in a population of children with fixed orthodontic appliances. Our results show an increase of Streptococcus mutans and Lactobacillus spp values during the follow-up. The whole dental workforce should be aware that preventive measures are of paramount importance during orthodontic treatment.

  12. International comparison of product certification and verification methods for appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

  13. International Comparison of Product Certification and Verification Methods for Appliances

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Nan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Romankiewicz, John [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fridley, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Zheng, Nina [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2012-06-01

    Enforcement of appliance standards and consumer trust in appliance labeling are important foundations of growing a more energy efficient economy. Product certification and verification increase compliance rates which in turn increase both energy savings and consumer trust. This paper will serve two purposes: 1) to review international practices for product certification and verification as they relate to the enforcement of standards and labeling programs in the U.S., E.U., Australia, Japan, Canada, and China; and 2) to make recommendations for China to implement improved certification processes related to their mandatory standards and labeling program such as to increase compliance rates and energy savings potential.

  14. Impact of Natural Gas Appliances on Pollutant Levels in California Homes

    Energy Technology Data Exchange (ETDEWEB)

    Mullen, Nasim A.; Li, Jina; Singer, Brett C.

    2012-12-01

    This report presents results from the first year of a 2-year study, investigating associations of five air pollutants (CO, NO2, NOX, formaldehyde and acetaldehyde) with the presence of natural gas appliances in California homes. From November 2011 to March 2012, pollutant concentration and occupant activity data were collected in 155 homes for 6-day periods. The sample population included both single-family (68%) and multi-family (32%) dwellings, with 87% having at least one gas appliance and 77% having an unvented gas cooking appliance. The geometric mean (GM) NO2 levels measured in the kitchen, bedroom and outside of homes were similar at values of 15, 12 and 11 ppb, respectively. In contrast, the GM NOx levels measured in the kitchen and bedroom of homes were much higher than levels measured outdoors, at levels of 42 and 41 ppb, compared to 19 ppb, respectively. Roughly 10% of sampled homes had 6-day average NO2 levels that exceeded the outdoor annual average limit set by the California Ambient Air Quality Standards (CAAQS) (30 ppb). The GMs of the highest 1-h and 8-h CO level measured in homes were 2.5 and 1.1 ppm, respectively. Four homes had a 1-h or 8-h concentration that exceeded the outdoor limits set by the CAAQS. The GM formaldehyde and acetaldehyde concentrations measured in homes were 15 and 7 ppb, respectively. Roughly 95% of homes had average formaldehyde levels indoors that exceeded the Chronic Reference Exposure Level set by the California EPA (7 ppb). Concentrations of NO2 and NOx, and to a lesser extent CO were associated with use of gas appliances, particularly unvented gas cooking appliances. Based on first principles, it is expected that effective venting of cooking pollutant emissions at the source will lead to a reduction of pollutant concentrations. However, no statistical association was detected between kitchen exhaust fan use and pollutant concentrations in homes in this study where gas cooking occurred frequently. The lack of

  15. Do you do Damon®? What is the current evidence base underlying the philosophy of this appliance system?

    Science.gov (United States)

    Wright, Natasha; Modarai, Faranak; Cobourne, Martyn T; Dibiase, Andrew T

    2011-09-01

    Self-ligating bracket systems are increasing in popularity amongst orthodontists. This reflects their high quality engineering, improved reliability and relative ease of use. However, it might also be related to claims of superior function made by the manufacturers of these appliances. In particular, the Damon(®) appliance system claims to offer significant advantages to both orthodontist and patient over conventional-ligation and other forms of self-ligated appliances. We have reviewed current literature relating to use of the Damon(®) appliance system. There is some evidence to suggest this appliance may lead to reductions in chairside time for the orthodontist, particularly those experienced with this system, in comparison to conventional-ligation. However, evidence that pain experience is reduced for the patient when using Damon(®) brackets is not conclusive. In the presence of identical archwire sequences, there is no evidence that Damon(®) brackets can align teeth faster or in a qualitatively differently manner, when compared with conventional-ligation. There is no high quality evidence that treatment with the Damon(®) appliance takes place more rapidly or leads to a superior occlusal or aesthetic result. Indeed, the best available evidence would suggest there is no difference in treatment outcome or time, at least in extraction cases. There is no evidence that treatment with the Damon(®) appliance is more stable. Claims relating to improved clinical performance of the Damon(®) appliance system are currently being made to orthodontists and patients that are not substantiated in the scientific literature.

  16. Space Maintenance with an Innovative ?Tube and Loop? Space Maintainer (Nikhil Appliance)

    OpenAIRE

    Srivastava, Nikhil; Grover, Jyotika; Panthri, Prerna

    2016-01-01

    ABSTRACT Despite the best efforts in prevention, premature loss of primary teeth continues to be a common problem in pediatric dentistry, resulting in disruption of arch integrity and adversely affecting the proper alignment of permanent successors. Space maintainers (SMs) are special appliances used for maintaining space created due to premature loss of primary teeth. Band and loop SM is mostly indicated for the premature loss of single primary molar, but this appliance has a number of limit...

  17. A new modified tandem appliance for management of developing Class III malocclusion

    OpenAIRE

    Sukh, Ram; Singh, Gyan P; Tandon, Pradeep

    2013-01-01

    Most developing Class III patients display a retruded maxilla. Early intervention in mixed dentition is associated with better patient compliance and possibly a better orthopedic response, which can produce favorable results. The aim of this article is to present the fabrication of the new modified tandem appliance and its use in management of developing Class III malocclusion. The therapeutic results of a new modified tandem appliance are presented in an 8 year-old male patient with anterior...

  18. Evaluation and development of a policy for waste generation control - electric and electronic waste management

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kwang Im [Korea Environment Institute, Seoul (Korea)

    1998-12-01

    Although a policy to reduce waste amount and promote recycling for large electric appliances was introduced, it is still in the initial stage operated in a form of recommendation and the general management system of electric and electronic waste has not established yet. In this study, the generation and disposal of electric and electronic waste were examined and the effectiveness of present policy was evaluated. Based on the analysis, a policy for the more appropriate electric and electronic waste management was presented. 34 refs., 4 figs., 51 tabs.

  19. Impact of wearing fixed orthodontic appliances on quality of life among adolescents: Case-control study.

    Science.gov (United States)

    Costa, Andréa A; Serra-Negra, Júnia M; Bendo, Cristiane B; Pordeus, Isabela A; Paiva, Saul M

    2016-01-01

    To investigate the impact of wearing a fixed orthodontic appliance on oral health-related quality of life (OHRQoL) among adolescents. A case-control study (1 ∶ 2) was carried out with a population-based randomized sample of 327 adolescents aged 11 to 14 years enrolled at public and private schools in the City of Brumadinho, southeast of Brazil. The case group (n  =  109) was made up of adolescents with a high negative impact on OHRQoL, and the control group (n  =  218) was made up of adolescents with a low negative impact. The outcome variable was the impact on OHRQoL measured by the Brazilian version of the Child Perceptions Questionnaire (CPQ 11-14) - Impact Short Form (ISF:16). The main independent variable was wearing fixed orthodontic appliances. Malocclusion and the type of school were identified as possible confounding variables. Bivariate and multiple conditional logistic regressions were employed in the statistical analysis. A multiple conditional logistic regression model demonstrated that adolescents wearing fixed orthodontic appliances had a 4.88-fold greater chance of presenting high negative impact on OHRQoL (95% CI: 2.93-8.13; P appliances. A bivariate conditional logistic regression demonstrated that malocclusion was significantly associated with OHRQoL (P  =  .017), whereas no statistically significant association was found between the type of school and OHRQoL (P  =  .108). Adolescents who wore fixed orthodontic appliances had a greater chance of reporting a negative impact on OHRQoL than those who did not wear such appliances.

  20. Low-power Appliance Recognition using Recurrent Neural Networks

    NARCIS (Netherlands)

    Rizky Pratama, Azkario; Simanjuntak, Frans Juanda; Lazovik, Aliaksandr; Aiello, Marco

    2018-01-01

    Indoor energy consumption can be understood by breaking overall power consumption down into individual components and appliance activations. The clas- sification of components of energy usage is known as load disaggregation or ap- pliance recognition. Most of the previous efforts address the

  1. Analysis appliance by gamma tomography with focused collimators

    International Nuclear Information System (INIS)

    Stoddart, H.F.

    1978-01-01

    This invention concerns nuclear medicine and specifically an image-forming appliance providing a very sensitive quantitative determination and the localization in space of the radioactivity of a body organ such as the brain of a patient to whom a substance labelled with radioactive isotopes has been administered. The characteristics of this appliance, which forms an image in a transversal scanning field by means of radioactive isotope radiations, includes several highly focused collimators, placed in line and focused inwards so that they form an arrangement that surrounds a given scanning field. Each collimator is mobile with respect to the adjacent collimator and a system moves the collimators so that the focus of each one uniformly samples at least a half of the total scanning field corresponding to a cross section. The number of detectors is an even one between two and twenty four, and the collimators are twelve in number [fr

  2. Vertical growth control during maxillary expansion using a bonded Hyrax appliance

    Directory of Open Access Journals (Sweden)

    Francisco Marcelo Paranhos Pinto

    2012-02-01

    Full Text Available INTRODUCTION: Rapid maxillary expansion (RME for the treatment of maxillary deficiency and posterior crossbite may induce changes in the vertical dimension. Expanders with occlusal splints have been developed to minimize unwanted vertical effects. OBJECTIVE: This preliminary study used cephalometri radiographs to evaluate the vertical effects of RME using a Hyrax appliance in children with maxillary deficiency. METHOD: Twenty-six patients (11 boys; mean age = 8 years and 5 months with maxillary deficiency and posterior crossbite were treated using a Hyrax appliance with an acrylic occlusal splint. Radiographs and cephalometric studies were performed before the beginning of the treatment (T1 and after RME active time (T2, at a mean interval of 7 months. Results were compared with normative values. RESULTS AND CONCLUSIONS: At the end of treatment, there were no statistically significant changes, and measurements were similar to the normative values. Data showed that there were no significant effects on vertical growth, which suggests that appliances with occlusal splints may be used to correct transverse deficiencies regardless of the patient's growth pattern.

  3. Stability of Class II fixed functional appliance therapy—a systematic review and meta-analysis

    Science.gov (United States)

    von Bremen, Julia; Ruf, Sabine

    2016-01-01

    Summary Objectives: To systematically search for scientific evidence concerning the stability of treatment (Tx) results achieved by means of Class II fixed functional appliance therapy and to assess possible differences between appliances. Search Methods: An electronic search of databases and orthodontic journals was carried out (until December 2013), with supplemental hand searching. In addition to the names of all identified appliances, the term fixed functional was used in combination with each of the following search terms: long-term, post-Tx, relapse, retention, stability. Selection Criteria: To be included in the review, the articles had to contain clear data on: Class II Tx with a fixed functional appliance (>5 patients), post-Tx period ≥ 1 year, assessment of ANB angle, Wits appraisal, molar relationship, soft-tissue profile convexity excluding the nose, overjet and/or overbite. Data Collection and Analysis: The literature search revealed 20 scientific investigations which corresponded to only two of the 76 identified appliances (Herbst and Twin Force Bite Corrector). As only one publication was found for the Twin Force Bite Corrector, a meta-analysis could only be performed for Herbst Tx. The data were extracted, pooled and weighted according to the number of patients in each study. Results: The mean values for post-Tx relapse (percentages relative to the Tx changes) were: ANB angle 0.2 degrees (12.4 per cent), Wits appraisal 0.5mm (19.5 per cent), sagittal molar relationship 1.2mm/0.1 cusp widths (21.8 per cent /6.5 per cent); soft-tissue profile convexity excluding nose less than 0.1 degrees (1.0 per cent), overjet 1.8mm (26.2 per cent), overbite Class II:1 1.4mm (44.7 per cent), overbite Class II:2 1.0mm (22.2 per cent). Conclusions: The scientific evidence concerning the stability of Tx results is inexistent for most fixed functional appliances for Class II correction except for Herbst appliance Tx. Even if the evidence level of most included studies

  4. Effect of material variation on the biomechanical behaviour of orthodontic fixed appliances: a finite element analysis.

    Science.gov (United States)

    Papageorgiou, Spyridon N; Keilig, Ludger; Hasan, Istabrak; Jäger, Andreas; Bourauel, Christoph

    2016-06-01

    Biomechanical analysis of orthodontic tooth movement is complex, as many different tissues and appliance components are involved. The aim of this finite element study was to assess the relative effect of material alteration of the various components of the orthodontic appliance on the biomechanical behaviour of tooth movement. A three-dimensional finite element solid model was constructed. The model consisted of a canine, a first, and a second premolar, including the surrounding tooth-supporting structures and fixed appliances. The materials of the orthodontic appliances were alternated between: (1) composite resin or resin-modified glass ionomer cement for the adhesive, (2) steel, titanium, ceramic, or plastic for the bracket, and (3) β-titanium or steel for the wire. After vertical activation of the first premolar by 0.5mm in occlusal direction, stress and strain calculations were performed at the periodontal ligament and the orthodontic appliance. The finite element analysis indicated that strains developed at the periodontal ligament were mainly influenced by the orthodontic wire (up to +63 per cent), followed by the bracket (up to +44 per cent) and the adhesive (up to +4 per cent). As far as developed stresses at the orthodontic appliance are concerned, wire material had the greatest influence (up to +155 per cent), followed by bracket material (up to +148 per cent) and adhesive material (up to +8 per cent). The results of this in silico study need to be validated by in vivo studies before they can be extrapolated to clinical practice. According to the results of this finite element study, all components of the orthodontic fixed appliance, including wire, bracket, and adhesive, seem to influence, to some extent, the biomechanics of tooth movement. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  5. Evaluation of dentoskeletal effects of Farmand functional appliance (Fa II on class II malocclusion

    Directory of Open Access Journals (Sweden)

    Yassaei S.

    2007-07-01

    Full Text Available Background and Aim: Functional appliances refer to a variety of removable or fixed appliances designed to alter the mandibular position both sagitally and vertically, resulting in orthodontic and orthopedic changes. Despite the long history of functional appliances, there is still much controversy related to their effectiveness and mode of action. The aim of this study was to evaluate dental and skeletal effects of Fa II in patients with class II malocclusion due to mandibular deficiency.Materials and Methods: In this before-after clinical trial, 35 patients with class II div I malocclusion were selected. These samples were under treatment with Fa II appliance for 11 months. The range of age of females was 10-13 years and males 11-14 years. Combination analysis was used to determine skeletal and dental effects. Paired t-test was used to compare the differences of mean value pre and post treatment. P<0.05 was considered as the level of significance. Results: There was significant difference between pre and post treatment in respect to posterior and anterior facial height, eruption of upper and lower posterior teeth, eruption of upper anterior teeth, mandibular body length, ANB angle, IMPA and 1 to SN. No significant difference was observed between pre and post treatment regarding facial growth.Conclusion: Treatment with Fa II functional appliance leads to significant alterations in dental and skeletal elements of craniofacial complex and improvement of dental and jaws relationship.

  6. The influence of different types of fixed orthodontic appliance on the growth and adherence of microorganisms (in vitro study).

    Science.gov (United States)

    Saloom, Hayder F; Mohammed-Salih, Harraa S; Rasheed, Shaymaa F

    2013-02-01

    Orthodontic appliances serve as different impact zones and modify microbial adherence and colonization, acting as foreign reserves and possible sources of infection. This study was conducted to investigate the effect of different types of fixed orthodontic appliances on the growth and adherence of microorganisms in oral flora which are Streptococcus mutans (S. mutans) and Candida albicans. Sixty-four of four different fixed orthodontic appliance-samples were used, divided into four groups of sixteen. Type I: Sapphire brackets- Coated wires, type II: Sapphire brackets- Stainless steel wires, type III: Stainless steel brackets- Coated wires and type IV: Stainless steel brackets- Stainless steel wires. Oral strains of S. mutans and Candida albicans were studied in the present study using biochemical test then microbial suspensions were prepared to do the tests of each microorganism including the antimicrobial effects of different appliance-samples on the growth of microorganisms and their adhesion tests. The results showed significant differences between the different appliances in terms of inhibition zone formation (PAppliance with high esthetic appearance, sapphire brackets and coated arch wire, showed the least adherence of S. mutans and Candida albicans in comparison to other appliances with less esthetic and more metal components. Key words:Orthodontic appliance, Adherence, Streptococcus mutans, Candida albicans.

  7. Short-term changes in chewing efficiency and subjective evaluation in normal dentate subjects after insertion of oral appliances with an occlusal flat table.

    Science.gov (United States)

    Satokawa, Y; Minami, I; Wakabayashi, N

    2018-02-01

    Oral appliances with an occlusal flat table are used as treatment dentures. However, the short-term effect of insertion of such oral appliances on chewing has not been reported. This study aimed to determine whether experimental and continuous insertion of oral appliances with an occlusal flat table has an effect on chewing efficiency and Oral Health Impact Profile (OHIP) in healthy participants. Ten participants each in the oral-appliance and control (no oral-appliance insertion) groups attended six data collection sessions for 5 consecutive days. Participants answered the OHIP questionnaire and underwent the chewing efficiency test. For each parameter, intergroup differences were investigated in terms of change from baseline to immediately after oral-appliance insertion (0 hour; P appliance insertion (P appliance insertion (P = .477 and .275, respectively). Differences between the two groups in the degree of change in other parameters were not significant. Insertion of oral appliances caused a decrease in chewing efficiency and an increase in OHIP scores. Continuous insertion improved functional limitation and physical pain within 96 hours. © 2017 John Wiley & Sons Ltd.

  8. Boundedly rational consumers, energy and investment literacy, and the display of information on household appliances

    NARCIS (Netherlands)

    Blasch, J.E.; Filippini, Massimo; Kumar, Nilkanth

    2017-01-01

    It is an ongoing debate how to increase the adoption of energy-efficient light bulbs and household appliances in the presence of the so-called ‘energy efficiency gap’. One measure to support consumers’ decision-making towards the purchase of more efficient appliances is the display of energy-related

  9. Treatment timing for functional jaw orthopaedics followed by fixed appliances: a controlled long-term study.

    Science.gov (United States)

    Pavoni, Chiara; Lombardo, Elisabetta Cretella; Lione, Roberta; Faltin, Kurt; McNamara, James A; Cozza, Paola; Franchi, Lorenzo

    2017-11-01

    To evaluate the role of treatment timing on long-term dentoskeletal effects of Class II treatment with removable functional appliances followed by full-fixed appliance therapy. A group of 46 patients (23 females and 23 males) with Class II malocclusion treated consecutively with either Bionator or Activator, followed by fixed appliances was compared with a matched control group of 31 subjects (16 females and 15 males) with untreated Class II malocclusion. The treated sample was evaluated at T1, start of treatment (mean age: 9.9 ± 1.3 years); T2, end of functional treatment and prior to fixed appliances (mean age: 11.9 ± 1.3 years); and T3, long-term observation (mean age: 18.3 ± 2.1 years). The treated and the control samples were divided into pre-pubertal and pubertal groups according to skeletal maturity observed at the start of treatment. Statistical comparisons were performed with independent sample t-tests. When treatment was initiated before puberty, Class II correction was mostly confined to the dentoalveolar changes, with significant improvements of both overjet and molar relationships. On the other hand, treatment with the outset at puberty produced significant long-term improvement of sagittal skeletal relationships, which were mainly sustained by mandibular changes. Treatment with removable functional appliances (Bionator or Activator) followed by full-fixed appliances produced significant skeletal long-term changes when it begins at puberty. Prepubertal Class II treatment results primarily in dentoalveolar changes. © The Author 2017. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com

  10. High-Resolution Gas Metering and Nonintrusive Appliance Load Monitoring System

    Science.gov (United States)

    Tewolde, Mahder

    This thesis deals with design and implementation of a high-resolution metering system for residential natural gas meters. Detailed experimental measurements are performed on the meter to characterize and understand its measurement properties. Results from these experiments are used to develop a simple, fast and accurate technique to non-intrusively monitor the gas consumption of individual appliances in homes by resolving small amounts of gas usage. The technique is applied on an existing meter retrofitted with a module that includes a high-resolution encoder to collect gas flow data and a microprocessor to analyze and identify appliance load profiles. This approach provides a number of appealing features including low cost, easy installation and integration with automated meter reading (AMR) systems. The application of this method to residential gas meters currently deployed is also given. This is done by performing a load simulation on realistic gas loads with the aim of identifying the necessary parameters that minimize the cost and complexity of the mechanical encoder module. The primary benefits of the system are efficiency analysis, appliance health monitoring and real-time customer feedback of gas usage. Additional benefits of include the ability to detect very small leaks and theft. This system has the potential for wide scale market adoption.

  11. Evaluating games console electricity use : technologies and policy options to improve energy efficiency.

    OpenAIRE

    Webb, Amanda E.

    2016-01-01

    Energy efficiency regulations and standards are increasingly being used as an approach to reduce the impact of appliances on climate change. Each new generation of games consoles is significantly different to the last and their cumulative electricity use has risen due to improved performance and functionality and increasing sales. As a result, consoles have been identified in the EU, US and Australia as a product group with the potential for significant electricity savings. However, there is ...

  12. Cost-effectiveness of high-efficiency appliances in the U.S. residential sector: A case study

    International Nuclear Information System (INIS)

    McNeil, Michael A.; Bojda, Nicholas

    2012-01-01

    This paper presents an analysis of the cost-effectiveness of high-efficiency appliances in the U.S. residential sector using cost and efficiency data developed as part of the regulatory process of the U.S. Department of Energy's Appliances and Commercial Equipment Standards Program. These data are presented as a case study in the development of an ‘efficiency technology database’ which can be expanded and published as a resource to other researchers and policy makers seeking scenarios that optimize efficiency policies and forecast their likely impacts on energy demand and greenhouse gas emissions. The use of this data to evaluate cost-effectiveness according to a variety of metrics is demonstrated using the example of one refrigerator–freezer product class. Cost-effectiveness is then evaluated in terms of cost of conserved energy for refrigerators, room air conditioners, water heaters, cooking equipment, central air conditioners and gas furnaces. The resulting potential of cost-effective improvement ranges from 1% to 53% of energy savings, with a typical potential of 15–20%. - Highlights: ► We determined the potential for cost-effective efficiency for residential appliances. ► We cover 6 appliance groups using cost of conserved energy as a metric for cost-effectiveness. ► Data are source from the DOE's Appliance and Commercial Equipment Standards Program. ► Between 15% and 20% additional cost-effective efficiency improvement is possible.

  13. Experimental evaluation of DC electric field effect on the thermoacoustic behaviour of flat premixed flames

    NARCIS (Netherlands)

    Volkov, E.N.; Kornilov, V.N.; Goey, de L.P.H.

    2013-01-01

    One promising approach to eliminate thermoacoustic instabilities in combustion appliances is the use of adaptive control of the flame/burner acoustic transfer function (TF). Application of a DC electric field (EF) as a spatially distributed, easily and quickly adjustable and low-energy method to

  14. Measuring equipment and regulation of gas consuming appliances. Requirements for measuring equipments and regulation of gas consuming appliances; Maeleudstyr og indregulering af gasforbrugende apparater. Krav til maeleudstyr og indregulering af gasforbrugende apparater. Projektrapport

    Energy Technology Data Exchange (ETDEWEB)

    Andersen, H.

    2004-06-01

    Regulation of gas consuming appliances has so far been regarded as a banality. However, during recent years a number of misunderstandings have arisen in this area. The load to which a gas consuming appliance should be regulated under practical conditions is often unclear. By way of example may be mentioned that the factory typically set the load using G20 reference gas (pure methane). Under practical Danish conditions the load (with Danish natural gas) is approx. 2% higher than the load set from the factory. This report focuses on the problems with varying gas composition in relation to regulation of gas consuming appliances. Furthermore, a number of unclear points concerning measuring equipment are dealt with. The report aims at offering suggestions for practical solutions. (BA)

  15. 78 FR 54450 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

    Science.gov (United States)

    2013-09-04

    ... Shelving and Racks From the People's Republic of China: Preliminary Results of Antidumping Duty... the antidumping duty order on certain kitchen appliance shelving and racks from the People's Republic...\\ is certain kitchen appliance shelving and racks. The subject merchandise is currently classifiable...

  16. A long-term controlled follow-up study of objective treatment need on young adults treated with functional appliances.

    Science.gov (United States)

    Faxén Sepanian, Varoojan; Paulsson-Björnsson, Liselotte; Kjellberg, Heidrun

    2014-01-01

    The aims of this study were to 1) evaluate the objective success rate of Class II malocclusion treatment with functional appliances five years after completion of treatment and 2) to compare the remaining objective treatment need with an untreated control group. Records of all listed patients between 18-20 years (n=1054) treated in a general practice were reviewed for the purpose of finding treatments with removable functional appliances. Among all subjects (n=61) who previously had been treated, 58 accepted to participate in the study.The test group was matched with an orthodontically untreated group with no history of objective treatment need. Clinical examination was performed and study casts and photos were taken from both groups.The objective treatment need was evaluated through clinical examination and study cast analysis with weighted Peer Assessment Rating index (wPAR). Twenty patients, (34.5%) (mean wPAR 13.8), succeeded with the functional appliance treatment.The wPAR score (mean 15.0) of the entire test group was significantly higher than the one of the control group (mean 7.3).The group that was treated exclusively with functional appliances had a mean wPAR score of 17.4. Eighteen patients (31.0%) who received retreatment with fixed appliances had a slightly higher mean wPAR (8.6) than the control group. Treatments with functional appliances in a general practice showed a high failure rate and a remaining treatment need. It is the treating dentist's responsibility to motivate the patient to cooperate to the treatment, because as it previously has been shown the treatment with functional appliances is a well-functioning treatment alternative with the cooperation of the patient being sufficient. It is also of importance, already before starting treatment, to estimate the child's cooperation ability and to avoid treatment with removable appliances if the child or parents are reluctant about such a treatment.

  17. A quantile approach to assess the effectiveness of the subsidy policy for energy-efficient home appliances: Evidence from Rizhao, China

    International Nuclear Information System (INIS)

    Yao, Xi-Long; Liu, Yang; Yan, Xiao

    2014-01-01

    A one-year subsidy program for energy-efficient home appliances has been implemented in China. We construct a dataset consisting of participant and non-participant households in both urban and rural areas of Rizhao city. By applying a quantile regression and counterfactual analysis, this study disentangles the impact of this subsidy program and inherent household attributes on per capita residential electricity consumption. First, contrary to the mean regression, the elasticity of electricity consumption to household's income, age, education and energy-saving awareness, varies markedly across the electricity consumption distribution and shows discrepancy between urban and rural areas. Second, while inherent household attributes are identified as a primary determinant to the changes in residential electricity consumption, the effect induced by the subsidy incentive is more significant at the middle of the electricity consumption distribution than at the tails. Third, there are significant rebound effects that lead to overall increase in household electricity consumption. Our results suggest that the disparity between urban and rural regions and targeted consumer behavior changes should be taken into account to ensure the effectiveness of a future energy-efficient subsidy program. - Highlights: • The effect of the subsidy policy on electricity consumption is assessed with a quantile regression. • Policy induced effect is more significant at the middle of the distribution than at the tails. • The rebound effects lead to overall increase in electricity consumption. • The impact of households attributes varies markedly across electricity consumption distribution

  18. Removable orthodontic appliance with nickel-titanium spring to reposition the upper incisors in an autistic patient.

    Science.gov (United States)

    Saito, Kan; Jang, Insan; Kubota, Kazumi; Hoshino, Tomonori; Hotokezaka, Hitoshi; Yoshida, Noriaki; Fujiwara, Taku

    2013-01-01

    A newly designed removable appliance with a shape-memory wire was used for the orthodontic treatment of the anterior teeth in an 11-year-old child who had autism and intellectual disability. The device was designed to reduce the lateral incisor crossbite and the central incisors' labial rotation. The child was treated for 1 year with this removable appliance. Tooth movement was analyzed using cephalograms and surface data were derived from study models. This device proved to be very durable. The lateral incisor crossbite was corrected, and the inclination of the upper central incisors and the interincisal angle were improved. This appliance exerts light and continuous orthodontic force, without requiring any adjustments of the spring wire. The appliance also facilitated orthodontic treatment in a child with intellectual disability in whom treatment with a standard orthodontic device would be unsuitable. ©2012 Special Care Dentistry Association and Wiley Periodicals, Inc.

  19. 46 CFR 199.176 - Markings on lifesaving appliances.

    Science.gov (United States)

    2010-10-01

    ... ARRANGEMENTS LIFESAVING SYSTEMS FOR CERTAIN INSPECTED VESSELS Requirements for All Vessels § 199.176 Markings on lifesaving appliances. (a) Lifeboats and rescue boats. Each lifeboat and rescue boat must be plainly marked as follows: (1) Each side of each lifeboat and rescue boat bow must be marked in block...

  20. Pre-directional appliance: A new approach to correct shifted premaxilla in bilateral cleft cases

    Directory of Open Access Journals (Sweden)

    P S Daigavane

    2011-01-01

    Full Text Available Management of bilateral cleft lip and palate cases is a challenging task, and if the premaxilla is shifted to either side, it poses a problem for the surgeon to operate and also for the orthodontist to do the orthodontic alignment. The aim of this study was to reposition the shifted premaxilla for better retraction with presurgical infant orthopedics, thus reducing the tissue tension and further scarring which have detrimental effects on maxillary growth. The innovative technique with pre-directional (PD appliance is easy to fabricate and use and works in this direction. Acrylic, springs, permasoft liner, elastics, retentive tapes. Previous approach for the shifted premaxilla was more focused on the surgical correction. In adults, surgery with osteotomy is the only option, with its own limitations and disadvantages, in repositioning the shifted premaxilla. Thus, PD appliance aids to correct the shifted premaxilla in presurgical molding stage. The premaxilla was thus shifted 5.5 mm to the left side, with premaxilla in facial symmetry, with the PD appliance. Presurgical orthopedics with PD appliance is worth in infants with shifted premaxilla in bilateral clefts cases.

  1. Effects of the Herbst appliance in growing orthodontic patients with different underlying vertical patterns.

    Science.gov (United States)

    Deen, Emily; Woods, Michael G

    2015-05-01

    The present study involved an assessment of the effects of the Herbst appliance used for Class II correction in subjects with different vertical facial patterns. Pre- and post-treatment lateral cephalograms of 91 growing Class II patients were divided into three vertical facial groups on the basis of mandibular plane angulation. All received a Herbst appliance and dental and skeletal changes were assessed in relation to pretreatment incisal overbite, overjet and the stage of cervical maturity. Herbst appliance treatment was accompanied by changes in the angulation of the upper and lower incisors, overjet reduction and an increase in mandibular length. In general, the rotational facial changes occurring during treatment were minimal, so that dolichofacial patterns remained long and brachyfacial patterns remained short. Herbst appliance treatment can be expected to result in considerable Class II dental correction. It is unlikely, however, that its use will be associated with clinically significant forward rotation in dolichofacial subjects. Since dolichofacial patterns are likely to remain long-faced, even after considerable Class II dental correction, orthognathic surgery may still be a consideration if normal facial proportions, without excessive facial convexity and lip strain, are treatment aims.

  2. Coordinated operation of a neighborhood of smart households comprising electric vehicles, energy storage and distributed generation

    NARCIS (Netherlands)

    Paterakis, N.G.; Erdinc, O.; Pappi, I.N.; Bakirtzis, A.G.; Catalao, J.P.S.

    2016-01-01

    In this paper, the optimal operation of a neighborhood of smart households in terms of minimizing the total energy procurement cost is analyzed. Each household may comprise several assets such as electric vehicles, controllable appliances, energy storage and distributed generation. Bi-directional

  3. An experiment with spectral analysis of emotional speech affected by orthodontic appliances

    Science.gov (United States)

    Přibil, Jiří; Přibilová, Anna; Ďuračková, Daniela

    2012-11-01

    The contribution describes the effect of the fixed and removable orthodontic appliances on spectral properties of emotional speech. Spectral changes were analyzed and evaluated by spectrograms and mean Welch’s periodograms. This alternative approach to the standard listening test enables to obtain objective comparison based on statistical analysis by ANOVA and hypothesis tests. Obtained results of analysis performed on short sentences of a female speaker in four emotional states (joyous, sad, angry, and neutral) show that, first of all, the removable orthodontic appliance affects the spectrograms of produced speech.

  4. 77 FR 72324 - Certain Kitchen Appliance Shelving and Racks from the People's Republic of China: Countervailing...

    Science.gov (United States)

    2012-12-05

    ... Shelving and Racks from the People's Republic of China: Countervailing Duty Administrative Review, 2010... countervailing duty order on certain kitchen appliance shelving and racks from the People's Republic of China. See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...

  5. Phase Balancing by Means of Electric Vehicles Single-Phase Connection Shifting in a Low Voltage Danish Grid

    DEFF Research Database (Denmark)

    Lico, Pasqualino; Marinelli, Mattia; Knezovic, Katarina

    2015-01-01

    In Denmark, household consumers are supplied with three phase with neutral cable. In addition, the distribution service operator cannot decide to which phase electrical appliance are connected. The technician who realizes the installation connects the loads according to his technical expertise...

  6. Magic Ring: A Finger-Worn Device for Multiple Appliances Control Using Static Finger Gestures

    Directory of Open Access Journals (Sweden)

    Tongjun Huang

    2012-05-01

    Full Text Available An ultimate goal for Ubiquitous Computing is to enable people to interact with the surrounding electrical devices using their habitual body gestures as they communicate with each other. The feasibility of such an idea is demonstrated through a wearable gestural device named Magic Ring (MR, which is an original compact wireless sensing mote in a ring shape that can recognize various finger gestures. A scenario of wireless multiple appliances control is selected as a case study to evaluate the usability of such a gestural interface. Experiments comparing the MR and a Remote Controller (RC were performed to evaluate the usability. From the results, only with 10 minutes practice, the proposed paradigm of gestural-based control can achieve a performance of completing about six tasks per minute, which is in the same level of the RC-based method.

  7. Occlusal bite force change after orthodontic treatment with Andresen functional appliance.

    Science.gov (United States)

    Al-Khateeb, Susan N; Abu Alhaija, Elham S; Majzoub, Sami

    2015-04-01

    The aim of this study was to determine the occlusal bite force (OBF) changes, at the incisal and molar regions, after orthodontic treatment with functional appliance therapy in preadolescent subjects. OBF was measured for patients (17 females and 16 males) before and after the treatment with Andresen functional appliance for an average period of 9 months (mean age was 11.8±1.1 years). Three variables were registered; maximum OBF at molar region and the average of three readings at the molar (AOBF) and incisal regions (IOBF). The same variables were measured in two occasions for a matching non-treated control group with a period of 9 months between the two measurements. No significant changes were seen in the OBF measured parameters in the control group. There was a reduction in all measured parameters. The mean reduction in maximum OBF was 76.1±12.4 N (P appliance caused a significant reduction in OBF immediately after treatment. © The Author 2014. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  8. The Hybrid Aesthetic Functional (HAF) Appliance: A Less Visible Proposal for Functional Orthodontics

    Science.gov (United States)

    2013-01-01

    In modern orthodontics, aesthetics appear to have a decisive influence on orthodontic appliance preferences and acceptability. This paper reports the early application of a newly emerged functional device with enhanced aesthetics in a Class II treatment. Patient perspectives and technical considerations are discussed along with recommendations for further design development. It can be assumed that the use of thermoplastic material-based appliances may meet both the therapeutic and aesthetic demands of young age groups. PMID:23956884

  9. Maxillary molar distalization or mandibular enhancement: a cephalometric comparison of comprehensive orthodontic treatment including the pendulum and the Herbst appliances.

    Science.gov (United States)

    Burkhardt, Donald R; McNamara, James A; Baccetti, Tiziano

    2003-02-01

    Several methods of Class II treatment that do not rely on significant patient compliance have become popular during the last decade, including several versions of the Herbst appliance and the pendulum or Pendex molar-distalization appliances. Yet, these 2 general approaches theoretically have opposite treatment effects, one presumably enhancing mandibular growth, and the other moving the maxillary teeth posteriorly. This study examined the treatment effects produced by 2 types of the Herbst appliance (acrylic splint and stainless-steel crown) followed by fixed appliances, and the pendulum appliance followed by fixed appliances. For each of the 3 treatment groups, lateral cephalograms were analyzed before the start of treatment (T1) and after the second phase of treatment (T2). Patients were matched according to age and sex. The comprehensive treatment time for the pendulum group was 31.6 months, and the acrylic and crowned Herbst groups were treated for 29.5 months and 28.0 months, respectively. Overall from T1 to T2, there were no statistically significant differences in mandibular growth among the 3 groups. Skeletal changes accounted for a larger portion of molar correction in the Herbst treatment groups than in the pendulum group. Patients in the pendulum group had an increase in the mandibular plane angle. Conversely, the mandibular plane angle in patients treated with either Herbst appliance closed slightly from T1 to T2. At T2, the chin points (pogonion) of patients in both Herbst groups, however, were located slightly more anteriorly than were the chin points of the pendulum patients. It is likely that the slight downward and backward rotation of the mandible occurring during treatment in the pendulum patients accounted for much of this difference. The treatment effects produced by the 2 types of Herbst appliance were similar at T2, in spite of their differences in design. It is important not to generalize the findings of this comparison beyond the appliance

  10. Anterior crossbite correction with a series of clear removable appliances: a case report.

    Science.gov (United States)

    Park, Jae Hyun; Kim, Tae Weon

    2009-01-01

    The Clear Aligner can be used to correct tooth movement without involving extraction, surgery, and other adjunct orthopedic appliances. The Clear Aligner is a procedure that can be performed by either an orthodontist or a general dentist without computer simulation/calculation. Since the Clear Aligner is fabricated from the stone model for new appliance at each or every other appointment, it is readily available to change the treatment sequence throughout the course of the treatment. The patient can receive any necessary dental procedures with ease during the course of the treatment. The treatment can also be easily resumed even if the patient has not worn the aligners for a period of time. The purpose of this article is to report dental anterior crossbite correction with a series of Clear Aligners. The Clear Aligner could be used as an alternative in appropriate cases for those who are reluctant with conventional appliances.

  11. Impact of Functional Appliances on Muscle Activity: A Surface Electromyography Study in Children

    Science.gov (United States)

    Woźniak, Krzysztof; Piątkowska, Dagmara; Szyszka-Sommerfeld, Liliana; Buczkowska-Radlińska, Jadwiga

    2015-01-01

    Background Electromyography (EMG) is the most objective tool for assessing changes in the electrical activity of the masticatory muscles. The purpose of the study was to evaluate the tone of the masseter and anterior temporalis muscles in growing children before and after 6 months of treatment with functional removable orthodontic appliances. Material/Methods The sample conisted of 51 patients with a mean age 10.7 years with Class II malocclusion. EMG recordings were performed by using a DAB-Bluetooth instrument (Zebris Medical GmbH, Germany). Recordings were performed in mandibular rest position, during maximum voluntary contraction (MVC), and during maximum effort. Results The results of the study indicated that the electrical activity of the muscles in each of the clinical situations was the same in the group of girls and boys. The factor that determined the activity of the muscles was their type. In mandibular rest position and in MVC, the activity of the temporalis muscles was significantly higher that that of the masseter muscels. The maximum effort test indicated a higher fatigue in masseter than in temporalis muscles. Conclusions Surface electromyography is a useful tool for monitoring muscle activity. A 6-month period of functional therapy resulted in changes in the activity of the masticatory muscles. PMID:25600247

  12. Fiscal 1999 achievement report. Development of technology for reducing power consumption during standby (Research and development of technologies for application of standby power reduction to domestic and office-automation appliances); 1999 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Kaden oyobi OA kiki no taiki denryoku sakugen jitsuyoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Efforts are exerted to develop power-efficient modules to be built into electrical products for reduction in power consumption in the standby state for domestic and office-automation appliances. In this study, television sets, audio sets, and air conditioners were selected out of domestic appliances and, out of office-automation appliances, notebook-size and desktop personal computers were selected. The standby power consumption is to be reduced to 3mW for domestic appliances, to 0.2W for notebook-size personal computers, and to 1/10-1/200 of the level being currently consumed in the case of desktop personal computers. For domestic appliances, a power efficient module not insulated from the AC power line was developed, to be built into a CPU-aided appliance to be turned on and off by remote control for the reduction of its standby power to 3mW. For notebook-size personal computers, a power-efficient power source insulated from the AC power line was developed, which consumes but 0.2W of standby power. It was built into a marketed notebook-size personal computer and tested for performance. For desktop personal computers, a 25mW power source insulated from the AC power line was fabricated, and tested for performance. (NEDO)

  13. Correction of complete maxillary crossbite with severe crowding using Hyrax expansion and fixed appliance.

    Science.gov (United States)

    Wangsrimongkol, Tasanee; Manosudprasit, Montian; Pisek, Poonsak; Leelasinjaroen, Pornnapha

    2013-09-01

    An 18-year-old Thai man who presented with a secondary cleft palate, maxillary hypoplasia and severe crowding was treated by rapid maxillary expansion and fixed orthodontic appliances. Initial assessment found skeletal Class III malrelationship and dental Class II malocclusion with anterior and bilateral posterior crossbites. Camouflage orthodontic treatment was planned using a rapid maxillary expansion appliance and correcting crowding with extraction all four premolar teeth. A Hyrax appliance and vertical loop arch wire were placed for maxillary arch expansion of 9.5 mms at first molars and canines, and 5.5 mms at the premolars and obtained positive overjet. Both acceptable skeletal and soft tissue relationships and satisfactory occlusion were produced. After 14 months of postoperative follow-up, the occlusal result was stable and no skeletal reversals could be detected.

  14. Labeling programs and efficiency standards to control the energy consumption of household appliances: current situation, main results and recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Menanteau, Ph.

    2000-09-01

    To control the rise in electricity consumption for specific uses, the industrialized countries started by introducing special programs aimed at improving energy efficiency. Among the different instruments available, labeling programs and minimum energy performance standards (MEPS) have proved to be very effective. The first part of this document presents the current situation, the main results and recommendations concerning the labeling programs and efficiency standards to control the energy consumption of household appliances. This analyze is done for each country in details providing the name of the program or measure, the date of implementation, the objective and the main characteristics of the program, the impacts and evaluation. (A.L.B.)

  15. Development and evaluation of a new depressurization spillage test for residential gas-fired combustion appliances : final report

    International Nuclear Information System (INIS)

    Edwards, P.

    2005-07-01

    This paper presented a newly developed combustion depressurization spillage test for residential combustion appliances. The test uses carbon dioxide (CO 2 ) that is produced in the fuel combustion process as a tracer gas. The test accurately measures the amount of combustion spillage from residential combustion appliances and their venting systems when they operate at certain levels of depressurization. Seven commonly used gas-fired appliances were used to evaluate the new test as well as the appliances. These included 2 power-vented storage-tank water heaters, 1 mid-efficiency furnace, 2 high-efficiency condensing furnaces, and 2 direct-vent gas fireplaces. Tests were performed for each unit with the test room initially depressurized by 50 Pa compared with the pressure outside the room. If the combustion spillage exceeded 2 per cent, the test was repeated with the room depressurized by 20 Pa, and then by 5 Pa. Each appliance was operated for 5 minutes of burner operation during which time the burner fuel consumption, the concentration of CO 2 and the exhaust fan flow rate were monitored. Measurements were taken for 2 minutes following burner shut off. The amount of CO 2 that was released into the test room from the appliance and its venting system was determined from the measurements and then compared with the amount of CO 2 that would be produced by combustion of the fuel that was consumed during the test. The ratio of the 2 provided a direct measure of the combustion spillage of the appliance and its venting system. The study revealed that 3 products had undetectable levels of combustion spillage, 3 products had low, but measurable combustion spillage, and 1 product had significant combustion spillage. refs., tabs., figs

  16. Field performance of wood-burning and coal-burning appliances in Crested Butte during the 1989-90 heating season. Final report

    International Nuclear Information System (INIS)

    Jaasma, D.R.; Champion, M.R.; Gundappa, M.

    1991-10-01

    The field performance of woodburning and coalburning appliances in and around Crested Butte, CO, has been evaluated. Measurements included particulate matter (PM), carbon monoxide (CO), and weekly average burn rates. Woodburning appliances included conventional airtight stoves, EPA-certified catalytic stoves, and EPA-certified noncatalytic stoves. Compared to the emissions measured from conventional stoves, the certified stoves reduced PM emission factors (g/kg) by 53% and CO emission factors by 49%. Coalburning appliances included a commercial scale boiler, a residential stoker, and hand-fired coalstove. The coalburning appliances were compared to conventional woodstoves on a grams of pollutant per joule of heat output basis. The automatically stoked coal appliances reduced PM and CO emissions by roughly 84% and 85%, respectively. The hand-fired stove was cleaner than expected, reducing PM by 55% and CO by 27%

  17. Electricity savings in Latvia through implementation of labelling directives. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    Legislation on labelling of household appliances was enforced in Latvia July 2001 to implement the European labelling directives. The project 'Electricity Savings in Latvia through Implementation of labelling Directives' was started January 2001 in order to support the implementation of the directives to ensure that they got an immediate effect. The project has included the following activities: Information of the general public and of traders and importers. In relation to the general public the activities consisted of production of a widely spread information brochure, TV-spots and a TV competition and participation in a school project. Seminars and meetings with traders and importers were held to inform about the legislation before it was enforced and to create a network for discussion of practical implementation problems and planning of the information activities. Test and control activities. The purpose of the test and control activities was to strengthen the test and control capacities and to transfer experience from Denmark. This was achieved though workshops for as well inspectors from the Consumer Rights Protection Centre and for members of the voluntary Consumer Protection Clubs. Results: It is assumed that the project has been very successful in the sense that the information about labelling of appliances has been efficiently spread via the information brochure, which was printed in 100.000 copies and distributed in shops, via Latvenergo and the consumer clubs. Furthermore, a cartoon about 'Energy-eaters' produced as part of the project by a very talented Latvian film study (Environmental Film Studio) has been used as TV-spot and has been broadcasted 40 times, including in connection to a morning TV-competition on labelling of appliances. The participatory approach used in the project has resulted in a very dedicated participation from the different stake holders side. Thus there is basis for sustainability in the sense, that a network

  18. Population at high-risk of indoor heatstroke: the usage of cooling appliances among urban elderlies in Japan.

    Science.gov (United States)

    Kondo, Masahide; Ono, Masaji; Nakazawa, Kouichi; Kayaba, Momoko; Minakuchi, Emiko; Sugimoto, Kazutoshi; Honda, Yasushi

    2013-05-01

    Heatstroke due to a heat wave during the summer is one of the commonly known health impacts of climate change in Japan. The elderly are particularly at high-risk of developing indoor heatstroke with poor prognosis. This study aims to describe the population among elderlies at high-risk of indoor heatstroke by focusing on the usage of cooling appliances. We conducted a web-based household survey in eight urban areas during the winter season of 2011. Households with a person aged 65 and over were selected as samples from panel members of a research firm, and the oldest member of the household was queried about his/her usage of cooling appliances. The population at high-risk of indoor heatstroke is defined as the elderly staying in a room without cooling appliances, or not using the installed cooling appliances, or turning the cooling appliances on only when the room temperature is above 28 °C. 15.4 and 19.1 % of the elderlies living in urban areas of Japan are identified as at high-risk of indoor heatstroke during activity time and sleeping time, respectively, according to the definition of high-risk of indoor heatstroke in this study. These figures are not negligible since the consequences of heatstroke are grave, but its risk can be eliminated by an appropriate usage of cooling appliances. The preventive interventions are needed to protect the elderlies at high-risk of heatstroke.

  19. Periodontal pathogen levels in adolescents before, during, and after fixed orthodontic appliance therapy.

    Science.gov (United States)

    Thornberg, Michelle J; Riolo, Christopher S; Bayirli, Burcu; Riolo, Michael L; Van Tubergen, Elizabeth A; Kulbersh, Richard

    2009-01-01

    This purpose of this study was to document and investigate changes in periodontal pathogen levels before, during, and after orthodontic treatment in adolescents. DNA gene probe analysis was used to quantify the levels of 8 periodontal pathogens before, during, and after treatment with fixed orthodontic appliances in 190 concurrently treated adolescent orthodontic patients. The 8 pathogens examined were Actinobacillus actinomycetemcomitans (AA), Porphyromonas gingivalis (PG), Prevotella intermedia (PI), Tannerella forsythia (TF), Eikenella corrodens (EC), Fusobacterium nucleatum (FN), Treponema denticola (TD), and Campylobacter rectus (CR). Chi-square tests were used to determine whether the percentages of subjects with high counts significantly changed over time. Logistic regression analyses were also performed to derive the relative risk of higher counts of pathogenic bacteria with fixed appliances at the various time intervals studied. For 6 (PI, TF, EC, FN, TD, CR) of the 8 pathogens, the percentages of subjects with high pathogen counts increased significantly after 6 months of fixed appliance treatment, but these returned to pretreatment levels by 12 months of orthodontic treatment. No pathogen level was significantly higher after 12 months of orthodontic treatment, and orthodontic treatment was found to be significantly protective for half of the pathogens (EC, FN, TD, CR) posttreatment. Orthodontic treatment with fixed appliances does not increase the risk of high levels of these periodontal pathogens.

  20. Insufficient evidence to confirm effectiveness of oral appliances in treatment of obstructive sleep apnoea syndrome in children.

    Science.gov (United States)

    Fox, Nigel A

    2007-01-01

    Searches were made using the Cochrane Central Register of Controlled Trials, Medline, Embase, Latin American and Caribbean Health Sciences Literature, Bibliografia Brasileira de Odontologia and SciELO (the Scientific Electronic Library Online). Studies chosen were randomised controlled trials (RCT) or quasi-RCT comparing all types of oral and functional orthopaedic appliances with placebo or no treatment, in children of 15 years old or younger. Data were independently extracted by two review authors. Authors were contacted for additional information. Risk ratios with 95% confidence intervals were calculated for all important dichotomous outcomes. A total of 384 trials were identified, of which only one, reporting results from a total of 23 patients, was suitable for inclusion in the review. Data provided in the published report did not answer all the questions from this review, but did answer some: the results presented favour treatment. At present there is not sufficient evidence to state that oral appliances or functional orthopaedic appliances are effective in the treatment of obstructive sleep apnoea (OSA) syndrome in children. Oral appliances or functional orthopaedic appliances may be helpful in the treatment of children with craniofacial anomalies which are risk factors for apnoea.

  1. Impact of orthodontic appliances on the quality of craniofacial anatomical magnetic resonance imaging and real-time speech imaging.

    Science.gov (United States)

    Wylezinska, Marzena; Pinkstone, Marie; Hay, Norman; Scott, Andrew D; Birch, Malcolm J; Miquel, Marc E

    2015-12-01

    The aim of this work was to investigate the effects of commonly used orthodontic appliances on the magnetic resonance (MR) image quality of the craniofacial region, with special interest in the soft palate and velopharyngeal wall using real-time speech imaging sequences and anatomical imaging of the temporomandibular joints (TMJ) and pituitaries. Common orthodontic appliances were studied on 1.5 T scanner using standard spin and gradient echo sequences (based on the American Society for Testing and Materials standard test method) and sequences previously applied for high-resolution anatomical and dynamic real-time imaging during speech. Images were evaluated for the presence and size of artefacts. Metallic orthodontic appliances had different effects on image quality. The most extensive individual effects were associated with the presence of stainless steel archwire, particularly if combined with stainless steel brackets and stainless steel molar bands. With those appliances, diagnostic quality of magnetic resonance imaging speech and palate images will be most likely severely degraded, or speech imaging and imaging of pituitaries and TMJ will be not possible. All non-metallic, non-metallic with Ni/Cr reinforcement or Ni/Ti alloys appliances were of little concern. The results in the study are only valid at 1.5 T and for the sequences and devices used and cannot necessarily be extrapolated to all sequences and devices. Furthermore, both geometry and size of some appliances are subject dependent, and consequently, the effects on the image quality can vary between subjects. Therefore, the results presented in this article should be treated as a guide when assessing the risks of image quality degradation rather than an absolute evaluation of possible artefacts. Appliances manufactured from stainless steel cause extensive artefacts, which may render image non-diagnostic. The presence and type of orthodontic appliances should be always included in the patient

  2. A randomized controlled trial of self-perceived pain, discomfort, and impairment of jaw function in children undergoing orthodontic treatment with fixed or removable appliances.

    Science.gov (United States)

    Wiedel, Anna-Paulina; Bondemark, Lars

    2016-03-01

    To compare patients' perceptions of fixed and removable appliance therapy for correction of anterior crossbite in the mixed dentition, with special reference to perceived pain, discomfort, and impairment of jaw function. Sixty-two patients with anterior crossbite and functional shift were recruited consecutively and randomized for treatment with fixed appliances (brackets and archwires) or removable appliances (acrylic plates and protruding springs). A questionnaire, previously found to be valid and reliable, was used for evaluation at the following time points: before appliance insertion, on the evening of the day of insertion, every day/evening for 7 days after insertion, and at the first and second scheduled appointments (after 4 and 8 weeks, respectively). Pain and discomfort intensity were higher for the first 3 days for the fixed appliance. Pain and discomfort scores overall peaked on day 2. Adverse effects on school and leisure activities were reported more frequently in the removable than in the fixed appliance group. The fixed appliance group reported more difficulty eating different kinds of hard and soft food, while the removable appliance group experienced more speech difficulties. No significant intergroup difference was found for self-estimated disturbance of appearance between the appliances. The general levels of pain and discomfort were low to moderate in both groups. There were some statistically significant differences between the groups, but these were only minor and with minor clinical relevance. As both appliances were generally well accepted by the patients, either fixed or removable appliance therapy can be recommended.

  3. 77 FR 12811 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Partial...

    Science.gov (United States)

    2012-03-02

    ... Shelving and Racks From the People's Republic of China: Partial Rescission of Antidumping Duty... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... Appliance Shelving and Racks from the People's Republic of China, dated January 10, 2012; and Letter to the...

  4. 76 FR 62765 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Preliminary...

    Science.gov (United States)

    2011-10-11

    ... Shelving and Racks From the People's Republic of China: Preliminary Results of the First Administrative... review of the antidumping duty order on certain kitchen appliance shelving and racks from the People's... administrative review of certain kitchen appliance shelving and racks from the PRC for the period March 5, 2009...

  5. Interoperability for smart appliances in the IoT world

    NARCIS (Netherlands)

    Daniele, L.; Solanki, M.; Hartog, F. den; Roes, J.

    2016-01-01

    Household appliances are set to become highly intelligent, smart and networked devices in the near future. Systematically deployed on the Internet of Things (IoT), they would be able to form complete energy consuming, producing, and managing ecosystems. Smart systems are technically very

  6. Managing intermittent sources of electricity: the prospects opened by research

    International Nuclear Information System (INIS)

    Bigot, Bernard

    2013-01-01

    Beyond the difficult question of foreseeing the additional cost of placing one kWh of electricity on the grid - a cost that must be kept as low as possible to improve the technology for harnessing and converting energy - the growing share of electricity from renewable energy sources in national consumption (initially in replacement of fossil fuels) raises questions for research. How to limit the factors that make most of these forms of energy intermittent? One solution involves developing local or centralized storage capacities that are technically and economically efficient. Another proposal has to do with introducing information technology in electricity grids and electric appliances in order to reverse the currently prevailing rationale so that demand adjusts to supply, and not the reverse, in proportions that, though probably limited, are indispensable

  7. Hoisting appliances and fuel handling equipment at nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-12-31

    The guide is followed by the Finnish Centre for Radiation and Nuclear Safety (STUK) in regulating hoisting and handling equipment Class 3 at nuclear facilities. The guide is applied e.g. to the following equipment: reactor building overhead cranes, hoisting appliances at nuclear fuel storages, fuel handling machines, other hoisting appliances, which because of nuclear safety aspects are classified in Safety Class 3, and load-bearing devices connected with the above equipment, such as replaceable hoisting tools and auxiliary lifting devices. The regulating of hoisting and handling equipment comprises the following stages: handling of preliminary and final safety analysis reports, inspection of the construction plan, supervision of fabrication and construction inspection, and supervision of initial start-up and commissioning inspection. 36 refs. Translation. The original text is published under the same guide number. The guide is valid from 5 January 1987 and will be in force until further notice.

  8. The quest to be "modern": The adoption of electric light, heat, and power technology in small-town America, 1883-1929

    Science.gov (United States)

    Hellrigel, Mary Ann

    This dissertation is a social, business, and technological history of electrification in the United States. It examines the origins of the electric utility industry, the development of light, heat and power technology, the marketing of electric service, and the adoption of electricity and domestic appliances in the late nineteenth and early twentieth centuries in two communities: Harrisburg and West Chester, Pennsylvania. Beginning in the 1880s, manufactured gas and electric utilities waged an intense and lengthy battle for the urban energy marketplace. Many villages, small towns and big cities had multiple gas and electric companies, driving technological change as they worked to increase reliability, lower costs, and improve lamps, lighting fixtures, and appliances. Producers as well as consumers grappled with these new sources of energy, looking for profitable and practical ways to incorporate them into everyday life. Gas and utility executives, locked in head-to-head competition, realized that marketing their invisible product was an uncertain process. Utilities redefined the concepts of "tradition" and "modernity" to attract investors and offer appliances and installation in addition to selling energy. Upper and middle class households seeking a modern comfortable home could use gas or electricity (and often both), while working classes made do with kerosene, coal and wood. Mixed technologies, based on consumer preference, access, product availability, price, and service greatly influenced the creation of "modern" America. Initially, Pennsylvania law mandated local energy systems-electricity and gas had to be consumed within the same town. Only in the early twentieth century were these laws amended to permit inter-connections, allowing merger and consolidation of utilities to serve a wider geographic area. By the 1910s, law, technology, and capital made it possible to abandon local central stations. In only a few decades, the industry shifted from locally

  9. The big chill puts the electric system under tension

    International Nuclear Information System (INIS)

    Huet, Sylvestre

    2012-01-01

    Written at the occasion of a cold wave in France in February 2012 with a new peak in electricity consumption, the article first analyses the specific meteorological conditions associated with this event, and then outlines that the massive use of electric heating makes the French system particularly sensitive to temperatures, but also that the peak is also due to the massive use of electric domestic appliances at about 7 p.m. He describes how this peak is faced in terms of energy sources and outlines that there was no risk for grid security. He comments the availability of nuclear and hydroelectric energy, and of other energies (oil, coal, gas), and the margin levels. He finally states that costs of a cold wave are predictable and could be mitigated by supporting the installation of energy-saving or non-electric heating systems

  10. Modeling hourly consumption of electricity and district heat in non-residential buildings

    International Nuclear Information System (INIS)

    Kipping, A.; Trømborg, E.

    2017-01-01

    Models for hourly consumption of heat and electricity in different consumer groups on a regional level can yield important data for energy system planning and management. In this study hourly meter data, combined with cross-sectional data derived from the Norwegian energy label database, is used to model hourly consumption of both district heat and electrical energy in office buildings and schools which either use direct electric heating (DEH) or non-electric hydronic heating (OHH). The results of the study show that modeled hourly total energy consumption in buildings with DEH and in buildings with OHH (supplied by district heat) exhibits differences, e.g. due to differences in heat distribution and control systems. In a normal year, in office buildings with OHH the main part of total modeled energy consumption is used for electric appliances, while in schools with OHH the main part is used for heating. In buildings with OHH the share of modeled annual heating energy is higher than in buildings with DEH. Although based on small samples our regression results indicate that the presented method can be used for modeling hourly energy consumption in non-residential buildings, but also that larger samples and additional cross-sectional information could yield improved models and more reliable results. - Highlights: • Schools with district heating (DH) tend to use less night-setback. • DH in office buildings tends to start earlier than direct electric heating (DEH). • In schools with DH the main part of annual energy consumption is used for heating. • In office buildings with DH the main part is used for electric appliances. • Buildings with DH use a larger share of energy for heating than buildings with DEH.

  11. Suggested Curriculum Guide for Developing a Program in Appliance Service and Repair. Bulletin No. 48-174.

    Science.gov (United States)

    Illinois State Board of Vocational Education and Rehabilitation, Springfield. Div. of Vocational and Technical Education.

    The outline curriculum guide has been developed to assist in planning, developing, and instructing a program in appliance service and repair. The material consists of a unit outline and suggested exercieses and assignments for 17 areas: shop mathematics, communication skills, safety, orientation to appliance service and repair, blueprint reading,…

  12. Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management.

    Science.gov (United States)

    Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

    2018-02-25

    The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism.

  13. Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

    Science.gov (United States)

    Silva, Bhagya Nathali; Khan, Murad; Han, Kijun

    2018-01-01

    The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST) algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism. PMID:29495346

  14. Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

    Directory of Open Access Journals (Sweden)

    Bhagya Nathali Silva

    2018-02-01

    Full Text Available The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage domestic energy consumption. Hence, we propose a smart home energy management system that reduces unnecessary energy consumption by integrating an automated switching off system with load balancing and appliance scheduling algorithm. The load balancing scheme acts according to defined constraints such that the cumulative energy consumption of the household is managed below the defined maximum threshold. The scheduling of appliances adheres to the least slack time (LST algorithm while considering user comfort during scheduling. The performance of the proposed scheme has been evaluated against an existing energy management scheme through computer simulation. The simulation results have revealed a significant improvement gained through the proposed LST-based energy management scheme in terms of cost of energy, along with reduced domestic energy consumption facilitated by an automated switching off mechanism.

  15. Compatibility of fixed orthodontic appliances with MR environment

    Czech Academy of Sciences Publication Activity Database

    Starčuk jr., Zenon; Hubálková, H.; Starčuková, Jana; Linetskiy, I.; Bartušek, Karel; Krupa, P.

    2006-01-01

    Roč. 19, Suppl. 1 (2006), EPOS 726:1-7 E-ISSN 1352-8661 R&D Projects: GA MZd NR8110 Institutional research plan: CEZ:AV0Z20650511 Keywords : orthodontic appliance * magnetic resonance * compatibility * dentistry * artifact Subject RIV: FS - Medical Facilities ; Equipment Impact factor: 0.756, year: 2005 http://posters.webges.com/esmrmb/epos

  16. Changes in oro-pharyngeal airway dimension after treatment with function appliance in class II skeletal pattern

    International Nuclear Information System (INIS)

    Ali, B.; Shaikh, A.; Fida, M.

    2015-01-01

    Background: Functional appliances have been used since many decades for the correction of mandibular retrognathism. Similar oral appliances are a treatment modality for patients with Obstructive sleep apnea. Hence, interception at the right age with these growth modification appliances might benefit a child from developing long term respiratory insufficiency. Therefore, the purpose of our study was to assess the short term effects of Twin block appliance (CTB) on pharyngeal airway size in subjects with skeletal Class II pattern in a sample of Pakistani population. Methods: A retrospective study was conducted from orthodontic records of 62 children (31 males, 31 females) with retrognathic mandibles using lateral cephalograms obtained at initial visit and after CTB treatment. Paired t-test was used to compare the pre-functional and post-functional treatment airway size. Independent sample t-test was used for comparison between the genders and statistical significance was kept at =0.05. Results: The upper airway width (p<0.001), nasopharyngeal depth (p=0.03) and upper airway thickness (p=0.008) was substantially improved after CTB treatment. Males showed a greater increase in upper airway width (p= 0.03) and nasopharyngeal depth (p=0.01) in comparison to the females. Conclusion: Functional appliance therapy can improve the narrow pharyngeal airway of growing children presenting with deficient mandibles having Class II skeletal pattern. (author)

  17. Load Balancing Integrated Least Slack Time-Based Appliance Scheduling for Smart Home Energy Management

    OpenAIRE

    Bhagya Nathali Silva; Murad Khan; Kijun Han

    2018-01-01

    The emergence of smart devices and smart appliances has highly favored the realization of the smart home concept. Modern smart home systems handle a wide range of user requirements. Energy management and energy conservation are in the spotlight when deploying sophisticated smart homes. However, the performance of energy management systems is highly influenced by user behaviors and adopted energy management approaches. Appliance scheduling is widely accepted as an effective mechanism to manage...

  18. Mini-screws, a viable adjunct along with Incognito lingual appliance: A case series

    Directory of Open Access Journals (Sweden)

    Wei Lin

    2015-01-01

    Full Text Available Invisible orthodontics have been around for too long, and with the advent of computer-aided design/computer-aided manufacturing technology appliances such as Incognito TM has made the whole treatment experience more pleasant and aesthetic. However, even in lingual orthodontics, biomechanics play the most important role, and the use of temporary anchorage devices (TADs has made the whole treatment more effective and efficient. This article focuses on cases where TADs in lingual appliances play a critical role in the treatment of various malocclusions.

  19. 77 FR 21744 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

    Science.gov (United States)

    2012-04-11

    ... Shelving and Racks From the People's Republic of China: Final Results of the Countervailing Duty... countervailable duty order on certain kitchen appliance shelving and racks (``Kitchen Racks'') from the People's... Kitchen Appliance Shelving and Racks from the People's Republic of China: Preliminary Results of...

  20. 78 FR 21594 - Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Final Results...

    Science.gov (United States)

    2013-04-11

    ... Shelving and Racks From the People's Republic of China: Final Results of Countervailing Duty Administrative... countervailing duty (``CVD'') order on certain kitchen appliance shelving and racks from the People's Republic of...\\ See Certain Kitchen Appliance Shelving and Racks From the People's Republic of China: Countervailing...