WorldWideScience

Sample records for earth metal salts

  1. 40 CFR 721.4668 - Hydrated alkaline earth metal salts of metalloid oxyanions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Hydrated alkaline earth metal salts of... Specific Chemical Substances § 721.4668 Hydrated alkaline earth metal salts of metalloid oxyanions. (a... hydrated alkaline earth metal salts of metalloid oxyanions (PMN P-94-1557) is subject to reporting under...

  2. Alkali earth metal extraction by zirconium salt of dibutylphosphoric acid

    International Nuclear Information System (INIS)

    Zil'berman, B.Ya.; Fedorov, Yu.S.; Shmidt, O.V.; Egorova, O.N.

    2006-01-01

    Zirconium salt of dibutyl phosphoric acid (ZS HDBP) could be used as a TBP-compatible solvent for the treatment of liquid radwaste containing long-lived radionuclides, strontium in particular. The alkali earth metals behaviour during their extraction with ZS HDBP and the influence of TBP on the extraction properties of ZS HDBP were investigated. The maximum of Sr extraction was observed at the molar ratio of Zr:HDBP = 1:9, which is also optimal for TPE and RE extraction. Distribution coefficients increase in the series Ba 3 ). Increase of nitric acid concentration resulted in a decrease of the Sr distribution coefficient with a slope of -3. The distribution coefficients of Sr showed quadratic dependence on the HDBP concentration. The presence of TBP in the solvent resulted in a minor decrease in Sr extraction, this effect being significantly lower than for TPE and RE during their extraction by ZS HDBP. At the same time, full saturation of solvent with Sr was not reached because of precipitation in the solvent phase. When xylene was used as the polar diluent for TBP, the influence of TBP on Sr extraction by ZS HDBP was not as significant as for the hydrocarbons, and the Sr distribution coefficients were ten times lower. Solvent saturation curves for Sr extraction by 0.4 mol/L ZS HDBP with xylene at Zr:HDBP = 1:9 showed that in the absence of TBP, the maximum solvent loading reached 0.014 mol/L Sr, which corresponded to Zr : Sr = 3:1. The solubility of Ca in the extract was significantly lower than that of Sr. A centrifugal contactor rig trial was carried out with the use of simulated solutions and 0.4 mol/L ZS HDBP in 30 % TBP with Isopar-L as the solvent. The extraction was performed while neutralizing the aqueous solution in the flow to a residual acidity of 0.05-0.2 mol/L, the stripping was performed by using 1-3 mol/L HNO 3 . Sr concentrating of 3 was achieved by purification from Cs of 50-100 during extraction from TPE and RE during selective stripping. Special

  3. Potassium salts of fatty acids as precipitating agents of alkaline earth metal ions

    International Nuclear Information System (INIS)

    Skrylev, L.D.; Sin'kova, L.A.

    1977-01-01

    Regularities have been studied of precipitation of ions of alkaline-earth elements with caprilate, pelargonate, caprinate, undecanate, laurate, tridecanate, myristate, pentadecanate, palmitate, and stearate of potassium. It has been shown that completeness of precipitation of metal ions is determined by the nature of alkaline-earth metal and potassium salt as well as by pH value and temperature of the solution. The study of temperature dependence of soaps of alkaline-earth metals makes it possible to calculate the heats of dissolution of laurates of alkaline-earth metals, and a change in entropy and free energy

  4. The electrodeposition and rare earths reduction in the molten salt actinides recovery systems using liquid metal

    International Nuclear Information System (INIS)

    Shim, J-B.; Lee, J-H.; Kwon, S-W.; Ahn, B-G.; Woo, M-S.; Lee, B-J.; Kim, E-H.; Park, H-S.; Yoo, J-H.

    2005-01-01

    A pyrochemical partitioning system uses liquid metals such as cadmium and bismuth in order to recover the actinide metals from a molten salt mixture containing rare earth fission product metals. The liquid metals play roles as a cathode in the electrowinning or an extracting phase in the reductive extraction operation. The product resulting from the above operations is metal-cadmium or-bismuth alloy, which should contain the rare earth element amounts as low as possible for a transmutation purpose. In this study, the electrodeposition behaviours of uranium and lanthanide elements such as La, Ce and Nd were investigated for solid molybdenum and liquid cadmium electrodes in a molten LiCl-KCl eutectic salt. Electrochemical methods used are a cyclic voltammetry (CV) and a chronopotentiometry for monitoring the salt phase and recovering the metals, respectively. The CV graphs for monitoring the oxidizing agent CdCl 2 in the salt phase were obtained. These show a time dependently disappearance of the oxidizing agent corresponding to the formation of UCl 3 by inserting the uranium metal into the salt. Also, a sequential oxidation technique which is added at a controlled amount of the oxidizing agents into the salt phase was applied. It was found that this method is feasible for the selective reduction of the rare earths content in liquid metal alloys. (author)

  5. Syntheses, structure and properties of Alkaline-earth metal salts of 4 ...

    Indian Academy of Sciences (India)

    The synthesis, crystal structure, spectral characteristics and thermal properties of alkaline-earth metal salts of 4-nitrophenylacetic acid (4-npaH) .... Isothermal weight loss studies were performed in a temperature controlled furnace. TG-DTA study ... resulted in the dissolu- tion of MCO3. Filtration followed by slow evaporation ...

  6. Development of electrolytic process in molten salt media for light rare-earth metals production. The metallic cerium electrodeposition

    International Nuclear Information System (INIS)

    Restivo, T.A.G.

    1994-01-01

    The development of molten salt process and the respective equipment aiming rare-earth metals recovery was described. In the present case, the liquid cerium metal electrodeposition in a molten electrolytes of cerium chloride and an equimolar mixture of sodium and potassium chlorides in temperatures near 800 C was studied. Due the high chemical reactivity of the rare-earth metals in the liquid state and their molten halides, an electrolytic cell was constructed with controlled atmosphere, graphite crucibles and anodes and a tungsten cathode. The electrolytic process variables and characteristics were evaluated upon the current efficiency and metallic product purity. Based on this evaluations, were suggested some alterations on the electrolytic reactor design and upon the process parameters. (author). 90 refs, 37 figs, 20 tabs

  7. Electrodeposition of alkali and alkali-earth metals on liquid lead cathodes in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Caravaca, C.; De Cordoba, G. [CIEMAT/DE/DFN/URAA. Avda. Complutense, 22. 28040 Madrid (Spain)

    2008-07-01

    Pyrochemical processing of spent nuclear fuel leads to the dissolution as chlorides of fission products (FPs) that have to be removed in order to recycle the salt. Precipitation technique have been tested for the removal of these FPs in the LiCl-KCl, salt selected as reference, with different results. Salt decontamination from lanthanides can be easily achieved as solid precipitates of oxychlorides or single phosphates; however, for the alkaline and alkaline-earth metals this technique is not suitable. Within the EUROPART project (VI FP of the EC), a new route that consist of the electrodeposition of these FP on a liquid lead cathode (LLC) has been considered, including the Li and K constituting the electrolyte. First results obtained with Sr and Cs are presented herein. Although according to the thermodynamic potential values, the electrodeposition order on LLC is Ba, Sr, Li, K and Cs, during our experiments it was not possible to distinguish the electrochemical signals corresponding to the individual elements. (authors)

  8. Modification of radiation sensitivity by salts of the metals beryllium and indium and the rare earths cerium, lanthanum and scandium

    International Nuclear Information System (INIS)

    Floersheim, G.L.

    1995-01-01

    The LD 50 of 46 salts of metals and rare earths (lanthanoids) was determined in mice. Half the LD 50 of the compounds was then combined with lethal radiation (10.5 Gy) and the modification of survival time was scored. Only the metals beryllium and indium and the rare earths cerium, lanthanum and scandium displayed activity in our assay. There were then tested at a wider range of lower doses and reduced survival time in a dose-dependent fashion. This appears to be compatible with enhancement of radiation sensitivity. The interaction of these metals and rare earths with radiation adds a new facet to their toxicological spectrum and, by enhancing radiation effects, may influence estimates of risk. On the other hand, radiosensitizing properties of the metals may be useful for further development of compounds to be used as adjuncts in specific situations of cancer radiotherapy. 31 refs., 1 fig., 1 tab

  9. Surface effect on the electronic and the magnetic properties of rock-salt alkaline-earth metal silicides

    International Nuclear Information System (INIS)

    Bialek, Beata; Lee, Jaeil

    2011-01-01

    An all electron ab-initio method was employed to study the electronic and the magnetic properties of the (001) surface of alkaline-earth metal silicides, CaSi, SrSi, and BaSi, in the rock-salt structure. The three compounds retain their ferromagnetic metallic properties at the surface. Due to the surface effects, the magnetism of the topmost layer is changed as compared with the bulk. This is a short-range effect. In CaSi, the magnetism of the surface layer is noticeably reduced, as compared with the bulk: magnetic moments (MMs) on both Ca and Si atoms are reduced. In SrSi (001), the polarization of electrons in the surface atoms is similar to that in the bulk atoms, and the values of MMs on the component atoms in the topmost layer do not change as much as in CaSi. In BaSi (001), the magnetic properties of Si surface atoms are enhanced slightly, and the magnetism of Ba atoms is not affected considerably by the surface effect. The calculated densities of states confirm the short-range effect of the surface on the electronic properties of the metal silicides.

  10. SEPARATION OF METAL SALTS BY ADSORPTION

    Science.gov (United States)

    Gruen, D.M.

    1959-01-20

    It has been found that certain metal salts, particularly the halides of iron, cobalt, nickel, and the actinide metals, arc readily absorbed on aluminum oxide, while certain other salts, particularly rare earth metal halides, are not so absorbed. Use is made of this discovery to separate uranium from the rare earths. The metal salts are first dissolved in a molten mixture of alkali metal nitrates, e.g., the eutectic mixture of lithium nitrate and potassium nitrate, and then the molten salt solution is contacted with alumina, either by slurrying or by passing the salt solution through an absorption tower. The process is particularly valuable for the separation of actinides from lanthanum-group rare earths.

  11. Electrochemical transient techniques for determination of uranium and rare-earth metal separation coefficients in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, S.A. [Institute of Chemistry, Kola Science Centre, RAS, Apatity, Murmansk Region 184200, Russia (Russian Federation)]. E-mail: kuznet@chemy.kolasc.net.ru; Hayashi, H. [Japan Atomic Energy Research Institute, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Minato, K. [Japan Atomic Energy Research Institute, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Gaune-Escard, M. [Ecole Polytechnique, IUSTI-CNRS UMR 6595, University of Provence, F-13453 Marseille, Cedex 13 (France)

    2006-02-25

    The main step in the pyrometallurgical recycling process of spent nuclear fuel is a molten salt electrorefining. The knowledge of separation coefficients of actinides (U, Np, Pu and Am) and rare-earth metals (Y, La, Ce, Nd and Gd) is very important for this step. Usually the separation coefficients are evaluated from the formal standard potentials of metals in melts containing their own ions, i.e. values obtained by potentiometric method. Electrochemical experiments were carried out at 723-823 K in order to estimate separation coefficients in LiCl-KCl eutectic melt containing uranium and lanthanum trichlorides. The electrochemical behaviour of UCl{sub 3} in LiCl-KCl melt was studied by different electrochemical methods. The diffusion coefficients of U(III) were determined by linear sweep voltammetry, chronopotentiometry and chronoamperometry. The standard rate constants of charge transfer for electroreduction of uranium, U(III) + 3e{sup -} {sup {yields}} U, were calculated by the impedance spectroscopy method. The values of constants testify that electroreduction of U(III) to U is mainly controlled by the rate of charge transfer. La(III) discharge on uranium electrode was also investigated. It was shown that for the calculation of uranium and lanthanum separation coefficients it is necessary to determine the voltammetric peak potentials of U(III) and La(III), their concentration in the melt and the kinetic parameters relating to U(III) discharge such as transfer and diffusion coefficients, and standard rate constants of charge transfer.

  12. Syntheses, structure and properties of Alkaline-earth metal salts of 4 ...

    Indian Academy of Sciences (India)

    technical details of data acquisition and selected crystal refinement ... An analysis revealed that all compounds which contain metal:4-npa in 1:2 ratio are differently hydrated with the metal:water ratios being 1:10, 1:2, 1:7.5 and 1:1 for Mg, Ca, Sr and Ba, respectively. ... ing vibration of the −NO2 group is also observed as a.

  13. Distribution behavior of uranium, neptunium, rare-earth elements ( Y, La, Ce, Nd, Sm, Eu, Gd) and alkaline-earth metals (Sr,Ba) between molten LiClKCI eutectic salt and liquid cadmium or bismuth

    Science.gov (United States)

    Kurata, M.; Sakamura, Y.; Hijikata, T.; Kinoshita, K.

    1995-12-01

    Distribution coefficients of uranium neptunium, eight rare-earth elements (Y, La, Ce, Pr, Nd, Sm, Eu and Gd) and two alkaline-earth metals (Sr and Ba) between molten LiCl-KCI eutectic salt and either liquid cadmium or bismuth were measured at 773 K. Separation factors of trivalent rare-earth elements to uranium or neptunium in the LiCl-KCl/Bi system were by one or two orders of magnitude larger than those in the LiCl-KCl/Cd system. On the contrary, the separation factors of alkaline-earth metals and divalent rare-earth elements to trivalent rare-earth elements were by one or two orders of magnitude smaller in the LiCl-KCl/Bi system.

  14. Distribution behavior of uranium, neptunium, rare-earth elements (Y, La, Ce, Nd, Sm, Eu, Gd) and alkaline-earth metals (Sr,Ba) between molten LiCl-KCl eutectic salt and liquid cadmium or bismuth

    International Nuclear Information System (INIS)

    Kurata, M.; Sakamura, Y.; Hijikata, T.; Kinoshita, K.

    1995-01-01

    Distribution coefficients of uranium neptunium, eight rare-earth elements (Y, La, Ce, Pr, Nd, Sm, Eu and Gd) and two alkaline-earth metals (Sr and Ba) between molten LiCl-KCl eutectic salt and either liquid cadmium or bismuth were measured at 773 K. Separation factors of trivalent rare-earth elements to uranium or neptunium in the LiCl-KCl/Bi system were by one or two orders of magnitude larger than those in the LiCl-KCl/Cd system. On the contrary, the separation factors of alkaline-earth metals and divalent rare-earth elements to trivalent rare-earth elements were by one or two orders of magnitude smaller in the LiCl-KCl/Bi system. (orig.)

  15. Metals removal from spent salts

    Science.gov (United States)

    Hsu, Peter C.; Von Holtz, Erica H.; Hipple, David L.; Summers, Leslie J.; Brummond, William A.; Adamson, Martyn G.

    2002-01-01

    A method and apparatus for removing metal contaminants from the spent salt of a molten salt oxidation (MSO) reactor is described. Spent salt is removed from the reactor and analyzed to determine the contaminants present and the carbonate concentration. The salt is dissolved in water, and one or more reagents may be added to precipitate the metal oxide and/or the metal as either metal oxide, metal hydroxide, or as a salt. The precipitated materials are filtered, dried and packaged for disposal as waste or can be immobilized as ceramic pellets. More than about 90% of the metals and mineral residues (ashes) present are removed by filtration. After filtration, salt solutions having a carbonate concentration >20% can be spray-dried and returned to the reactor for re-use. Salt solutions containing a carbonate concentration ion exchange column, which yields salt solutions that contain less than 1.0 ppm of contaminants.

  16. Separation of rare earths from transition metals by liquid-liquid extraction from a molten salt hydrate to an ionic liquid phase.

    Science.gov (United States)

    Rout, Alok; Binnemans, Koen

    2014-02-28

    The solvent extraction of trivalent rare-earth ions and their separation from divalent transition metal ions using molten salt hydrates as the feed phase and an undiluted fluorine-free ionic liquid as the extracting phase were investigated in detail. The extractant was tricaprylmethylammonium nitrate, [A336][NO3], and the hydrated melt was calcium nitrate tetrahydrate, Ca(NO3)2·4H2O. The extraction behavior of rare-earth ions was studied for solutions of individual elements, as well as for mixtures of rare earths in the hydrated melt. The influence of different extraction parameters was investigated: the initial metal loading in the feed phase, percentage of water in the feed solution, equilibration time, and the type of hydrated melt. The extraction of rare earths from Ca(NO3)2·4H2O was compared with extraction from CaCl2·4H2O by [A336][Cl] (Aliquat 336). The nitrate system was found to be the better one. The extraction and separation of rare earths from the transition metals nickel, cobalt and zinc were also investigated. Remarkably high separation factors of rare-earth ions over transition metal ions were observed for extraction from Ca(NO3)2·4H2O by the [A336][NO3] extracting phase. Furthermore, rare-earth ions could be separated efficiently from transition metal ions, even in melts with very high concentrations of transition metal ions. Rare-earth oxides could be directly dissolved in the Ca(NO3)2·4H2O phase in the presence of small amounts of Al(NO3)3·9H2O or concentrated nitric acid. The efficiency of extraction after dissolving the rare-earth oxides in the hydrated nitrate melt was identical to extraction from solutions with rare-earth nitrates dissolved in the molten phase. The stripping of the rare-earth ions from the loaded ionic liquid phase and the reuse of the recycled ionic liquid were also investigated in detail.

  17. Kinetic study of the α-tocopherol-regeneration reaction of ubiquinol-10 in methanol and acetonitrile solutions: notable effect of the alkali and alkaline earth metal salts on the reaction rates.

    Science.gov (United States)

    Mukai, Kazuo; Oi, Masanori; Ouchi, Aya; Nagaoka, Shin-ichi

    2012-03-01

    A kinetic study of regeneration reaction of α-tocopherol (α-TocH) by ubiquinol-10 has been performed in the presence of four kinds of alkali and alkaline earth metal salts (LiClO(4), NaClO(4), NaI, and Mg(ClO(4))(2)) in methanol and acetonitrile solutions, using double-mixing stopped-flow spectrophotometry. The second-order rate constants (k(r)'s) for the reaction of α-tocopheroxyl (α-Toc•) radical with ubiquinol-10 increased and decreased notably with increasing concentrations of metal salts in methanol and acetonitrile, respectively. The k(r) values increased in the order of no metal salt NaClO(4) ~ NaI > LiClO(4) > Mg(ClO(4))(2) at the same concentration of metal salts. The metal salts having a smaller ionic radius of cation and a larger charge of cation gave a larger k(r) value in methanol, and a smaller k(r) value in acetonitrile. The effect of anion was almost negligible in both the solvents. Notable effects of metal cations on the UV-vis absorption spectrum of α-Toc• radical were observed in aprotic acetonitrile solution, suggesting complex formation between α-Toc• and metal cations. On the other hand, effects of metal cations were negligible in protic methanol, suggesting that the complex formation between α-Toc• and metal cations is hindered by the hydrogen bond between α-Toc• and methanol molecules. The difference between the reaction mechanisms in methanol and acetonitrile solutions was discussed on the basis of the results obtained. High concentrations of alkali and alkaline earth metal salts coexist with α-TocH and ubiquinol-10 in plasma, blood, and many tissues, suggesting the contribution of the metal salts to the above regeneration reaction in biological systems.

  18. Study of absorption spectra for alkali and alkaline earth metal salts in flameless atomic absorption spectrometry using a carbon tube atomizer

    International Nuclear Information System (INIS)

    Yasuda, Seiji; Kakiyama, Hitoo

    1975-01-01

    Absorption spectra of various salts such as alkali metal salts, alkaline earth dichlorides, and ammonium halides were investigated and absorptions of some molecular species produced in the carbon tube were identified. The aqueous solution (20 μl) containing 1.0 mg/ml of each salt was placed in the carbon tube atomizer and heated in a similar manner to usual flameless atomic absorption method. D 2 -lamp was used as a continuous light source and argon gas was employed as an inert sheath gas. The spectra were obtained over the range of wavelength 200 to 350 nm. When alkali halides were feeded, the absorption spectra agreed with those of alkali halide vapors. Therefore, in such cases vapors of the alkali halides were probably produced by the sublimation or vaporization in the atomizer. The spectra of alkali perchlorates were considered to be those of alkali chlorides produced by the pyrolysis of the perchlorates in the atomizer. The absorptions of alkaline earth chlorides below 250 nm were probably due to their gaseous states. Sulfur dioxide was found to be produced by the pyrolysis of alkali sulfates, bisulfates and sulfites in the atomizer, Alkali phosphates and pyrophosphates gave almost identical spectra below 300 nm. Gamma band spectrum of nitrogen monoxide was observed from 200 to 240 nm during ashing at bout 330 0 C for alkali nitrates and nitrites. Ammonia vapor was produced from ammonium halides during drying at about 170 0 C. Although the absorptions of alkali carbonates and hydroxides were almost undetectable, the same spectra as those of alkali halides were observed by the addition of ammonium halides to the solutions of alkali compounds. This shows that alkali halides are produced in the atomizer by the addition of halide ions. (auth.)

  19. The coordination complex structures and hydrogen bonding in the three-dimensional alkaline earth metal salts (Mg, Ca, Sr and Ba) of (4-aminophenyl)arsonic acid.

    Science.gov (United States)

    Smith, Graham; Wermuth, Urs D

    2017-01-01

    (4-Aminophenyl)arsonic acid (p-arsanilic acid) is used as an antihelminth in veterinary applications and was earlier used in the monosodium salt dihydrate form as the antisyphilitic drug atoxyl. Examples of complexes with this acid are rare. The structures of the alkaline earth metal (Mg, Ca, Sr and Ba) complexes with (4-aminophenyl)arsonic acid (p-arsanilic acid) have been determined, viz. hexaaquamagnesium bis[hydrogen (4-aminophenyl)arsonate] tetrahydrate, [Mg(H 2 O) 6 ](C 6 H 7 AsNO 3 )·4H 2 O, (I), catena-poly[[[diaquacalcium]-bis[μ 2 -hydrogen (4-aminophenyl)arsonato-κ 2 O:O']-[diaquacalcium]-bis[μ 2 -hydrogen (4-aminophenyl)arsonato-κ 2 O:O

  20. Kinetic study of the aroxyl radical-scavenging reaction of alpha-tocopherol in methanol solution: notable effect of the alkali and alkaline earth metal salts on the reaction rates.

    Science.gov (United States)

    Ouchi, Aya; Nagaoka, Shin-ichi; Abe, Kouichi; Mukai, Kazuo

    2009-10-08

    A kinetic study of the aroxyl (ArO*) radical-scavenging reaction of alpha-tocopherol (alpha-TocH) has been performed in the presence of six kinds of alkali and alkaline earth metal salts (LiI, LiClO(4), NaI, NaClO(4), KI, and Mg(ClO(4))(2)) in methanol solution, using stopped-flow spectrophotometry. The decay rate of the ArO* for the reaction of alpha-TocH with ArO* increased linearly with increasing concentration of metal salts. The second-order rate constants (k(s)) for the reaction of alpha-TocH with ArO* increased in the order of no metal salt concentration of metal salts. For example, the k(s) values in methanol solution including 4.00 x 10(-1) M of LiI and Mg(ClO(4))(2) were 3.04 and 1.30 times larger than that in the absence of metal salts, respectively. The alkali and alkaline earth metal salts having smaller ionic radius of cation and anion and larger charge of cation gave larger rate constants (k(s)). Effects of metal cations on the UV-vis absorption spectra of the alpha-Toc* (and ArO*) radical were negligible in methanol solution, suggesting that the complex formation between the alpha-Toc* (and ArO*) radical molecule and metal cations is hindered by the hydrogen bond between radical and methanol molecules. The results indicate that the hydrogen transfer reaction of alpha-TocH proceeds via an electron transfer intermediate from alpha-TocH to ArO* radicals followed by proton transfer. Both the coordinations of metal cations to the one-electron reduced anions of ArO* (ArO: (-)) and of counteranions to the one-electron oxidized cations of alpha-TocH (alpha-TocH(+)*) may stabilize the intermediate, resulting in the acceleration of electron transfer. On the other hand, the effect of metal salts on the rate of bimolecular self-reaction (2k(d)) of the alpha-Toc* radical was not observed. The result suggests that the hydrogen transfer reaction between two alpha-Toc* radical molecules proceeds via a one-step hydrogen atom transfer mechanism rather than via an

  1. CO2 gasification reactivity of biomass char: catalytic influence of alkali, alkaline earth and transition metal salts.

    Science.gov (United States)

    Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

    2013-09-01

    This study investigates the influence of alkali (Na, K), alkaline earth (Ca, Mg) and transition (Fe) metal nitrates on CO2 gasification reactivity of pistachio nut shell (PNS) char. The preliminary gasification experiments were performed in thermogravimetric analyzer (TGA) and the results showed considerable improvement in carbon conversion; Na-char>Ca-char>Fe-char>K-char>Mg-char>raw char. Based on TGA studies, NaNO3 (with loadings of 3-7 wt%) was selected as the superior catalyst for further gasification studies in bench-scale reactor; the highest reactivity was devoted to 5 wt% Na loaded char. The data acquired for gasification rate of catalyzed char were fitted with several kinetic models, among which, random pore model was adopted as the best model. Based on obtained gasification rate constant and using the Arrhenius plot, activation energy of 5 wt% Na loaded char was calculated as 151.46 kJ/mol which was 53 kJ/mol lower than that of un-catalyzed char. Copyright © 2013 Elsevier Ltd. All rights reserved.

  2. Oxidation by metal salts

    International Nuclear Information System (INIS)

    Makhon'kov, D.I.; Cheprakov, A.V.; Rodkin, M.A.; Mil'chenko, A.Yu.; Beletskaya, I.P.

    1986-01-01

    Oxidation of toluene and para-substituted toluenes containing electron acceptor groups: p-toluic acid, p-methyltoluylate and p-nitrotoluene by ammonium cerium (4) nitrate and ammonium cerium (4) sulfate in aqueous solutions of trifluoroacetic acid in the presence of chlorides and bromides of alkali metals is studied. The rate and selectivity of oxidative halogenation in side chain and/or aromatic ring under the conditions studied depend both on the nature of substrate and halogenide-ion and on the reaction conditions and ligand surrounding of cerium (4) atom

  3. Metal salt catalysts for enhancing hydrogen spillover

    Science.gov (United States)

    Yang, Ralph T; Wang, Yuhe

    2013-04-23

    A composition for hydrogen storage includes a receptor, a hydrogen dissociating metal doped on the receptor, and a metal salt doped on the receptor. The hydrogen dissociating metal is configured to spill over hydrogen to the receptor, and the metal salt is configured to increase a rate of the spill over of the hydrogen to the receptor.

  4. Synthesis of carbides of refractory metals in salt melts

    International Nuclear Information System (INIS)

    Ilyushchenko, N.G.; Anfinogenov, A.I.; Chebykin, V.V.; Chernov, Ya.B.; Shurov, N.I.; Ryaposov, Yu.A.; Dobrynin, A.I.; Gorshkov, A.V.; Chub, A.V.

    2003-01-01

    The ion-electron melts, obtained through dissolving the alkali and alkali-earth metals in the molten chlorides above the chloride melting temperature, were used for manufacturing the high-melting metal carbides as the transport melt. The lithium, calcium and magnesium chlorides and the mixture of the lithium chloride with the potassium or calcium chloride were used from the alkali or alkali-earth metals. The metallic lithium, calcium, magnesium or the calcium-magnesium mixtures were used as the alkali or alkali-earth metals. The carbon black or sugar was used as carbon. It is shown, that lithium, magnesium or calcium in the molten salts transfer the carbon on the niobium, tantalum, titanium, forming the carbides of the above metals. The high-melting metal carbides are obtained both from the metal pure powders and from the oxides and chlorides [ru

  5. Biosorption of metal and salt tolerant microbial isolates from a former uranium mining area. Their impact on changes in rare earth element patterns in acid mine drainage.

    Science.gov (United States)

    Haferburg, Götz; Merten, Dirk; Büchel, Georg; Kothe, Erika

    2007-12-01

    The concentration of metals in microbial habitats influenced by mining operations can reach enormous values. Worldwide, much emphasis is placed on the research of resistance and biosorptive capacities of microorganisms suitable for bioremediation purposes. Using a collection of isolates from a former uranium mining area in Eastern Thuringia, Germany, this study presents three Gram-positive bacterial strains with distinct metal tolerances. These strains were identified as members of the genera Bacillus, Micrococcus and Streptomyces. Acid mine drainage (AMD) originating from the same mining area is characterized by high metal concentrations of a broad range of elements and a very low pH. AMD was analyzed and used as incubation solution. The sorption of rare earth elements (REE), aluminum, cobalt, copper, manganese, nickel, strontium, and uranium through selected strains was studied during a time course of four weeks. Biosorption was investigated after one hour, one week and four weeks by analyzing the concentrations of metals in supernatant and biomass. Additionally, dead biomass was investigated after four weeks of incubation. The maximum of metal removal was reached after one week. Up to 80% of both Al and Cu, and more than 60% of U was shown to be removed from the solution. High concentrations of metals could be bound to the biomass, as for example 2.2 mg/g U. The strains could survive four weeks of incubation. Distinct and different patterns of rare earth elements of the inoculated and non-inoculated AMD water were observed. Changes in REE patterns hint at different binding types of heavy metals regarding incubation time and metabolic activity of the cells. (c) 2008 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Investigation of the evaporation of rare earth chlorides in a LiCl-KCl molten salt

    International Nuclear Information System (INIS)

    Sung Bin Park; Dong Wook Cho; Moon Sik Woo; Sung Chan Hwang; Young Ho Kang; Jeong Guk Kim; Hansoo Lee

    2011-01-01

    Uranium dendrites which were deposited at a solid cathode of an electrorefiner contained a certain amount of salts. These salts should be removed for the recovery of pure metal using a cathode processor. In the uranium deposits from the electrorefining process, there are actinide chlorides and rare earth chlorides in addition to uranium chloride in the LiCl-KCl eutectic salt. The evaporation behaviors of the actinides and rare earth chlorides in the salts should be investigated for the removal of salts in the deposits. Experiments on the salt evaporation of rare earth chlorides in a LiCl-KCl eutectic salt were carried out. Though the vapor pressures of the rare earth chlorides were lower than those of the LiCl and KCl, the rare earth chlorides were co-evaporized with the LiCl-KCl eutectic salt. The Hertz-Langmuir relation was applied for this evaporation, and also the evaporation rates of the salt were obtained. The co-evaporation of the rare earth chlorides and LiCl-KCl eutectic were also discussed. (author)

  7. Metals in Metal Salts: A Copper Mirror Demonstration

    Science.gov (United States)

    Pike, Robert D.

    2010-01-01

    A simple lecture demonstration is described to show the latent presence of metal atoms in a metal salt. Copper(II) formate tetrahydrate is heated in a round-bottom flask forming a high-quality copper mirror.

  8. Electron spin resonance study of electron localization and dynamics in metal-molten salt solutions: comparison of M-MX and Ln-LnX sub 3 melts (M alkali metal, Ln = rare earth metal, X = halogen)

    CERN Document Server

    Terakado, O; Freyland, W

    2003-01-01

    We have studied the electron spin resonance (ESR) spectra in liquid K-KCl and M-(NaCl/KCl) sub e sub u sub t mixtures at different concentrations in salt-rich melts approaching the metal-nonmetal transition region. In both systems F-centre-like characteristics are found. Strongly exchange narrowed signals clearly indicate that fast electron exchange occurs on the picosecond timescale. In contrast, the ESR spectra of a (NdCl sub 2)(NdCl sub 3)-(LiCl/KCl) sub e sub u sub t melt are characterized by a large line width of the order of 10 sup 2 mT which decreases with increasing temperature. In this case, the g-factor and correlation time are consistent with the model of intervalence charge transfer, which is supported by recent conductivity and optical measurements. The different transport mechanisms will be discussed.

  9. Titanium metal obtention by fused salts electrolysis

    International Nuclear Information System (INIS)

    Perillo, P.M.; Ares, Osvaldo; Botbol, Jose.

    1989-01-01

    Potassium fluorotitanate dissolved in fused sodium chloride or potassium chloride may be electrolyzed under an inert gas atmosphere. Solid electrolysis products are formed on the cathode which contains titanium metal, sodium chloride, lower fluorotitanates and small quantities of alkali metal fluorotitanate. The extraction of titanium from the electrolysis products may be carried out by aqueous leaching (removal of chloride salts of alkali metals and a certain amount of fluorotitanates). Titanium metal obtained is relatively pure. (Author)

  10. Development of electrolytic process in molten salt media for light rare-earth metals production. The metallic cerium electrodeposition; Desenvolvimento de processo de eletrolise em meio de sais fundidos para a producao de metais de terras-raras leves. A obtencao do cerio metalico

    Energy Technology Data Exchange (ETDEWEB)

    Restivo, T.A.G.

    1994-12-31

    The development of molten salt process and the respective equipment aiming rare-earth metals recovery was described. In the present case, the liquid cerium metal electrodeposition in a molten electrolytes of cerium chloride and an equimolar mixture of sodium and potassium chlorides in temperatures near 800{sup C} was studied. Due the high chemical reactivity of the rare-earth metals in the liquid state and their molten halides, an electrolytic cell was constructed with controlled atmosphere, graphite crucibles and anodes and a tungsten cathode. The electrolytic process variables and characteristics were evaluated upon the current efficiency and metallic product purity. Based on this evaluations, were suggested some alterations on the electrolytic reactor design and upon the process parameters. (author). 90 refs, 37 figs, 20 tabs.

  11. Metal Oxide Solubility and Molten Salt Corrosion.

    Science.gov (United States)

    1982-03-29

    soluble oxides that relations like eq. (3) are significant. The oxides of several metal oxides have been found to be amphoteric , i.e., their solution...METAL OXIDE SOLUBILITY AND MOLTEN SALT CORROSION.(U) MAR 82 K H STERN UNCLASSI E DL R L-4772NL EL .2. MICROCOPY RESOLUTION TEST CHART NATIONAL BURALU...METAL OXIDE SOLUBILITY AND MOLTEN SALT Interim report on a continuing CORROSION NRL problem. S. PERFORMING a4. REPORT NUMlER 7. AuTtwORr) S. CONTRACT OR

  12. Preparation and refining of rare earth metals by electrolytic routes

    International Nuclear Information System (INIS)

    Sahoo, D.K.

    2007-01-01

    Rare earth production has been gaining importance for the last 25 years for a variety of uses ranging from nuclear applications to hydrogen storage materials. Numerous techniques have been formulated to successfully extract pure metal from the ores and amongst them molten salt electrometallurgy looks promising. It being simple, environmental friendly makes the process technoeconomical for some rare earths. However serious issues like high temperature molten salt corrosion and suitability and selection of electrolytes needs to he considered to make the process an industrial one

  13. Latent energy storage with salt and metal mixtures for solar dynamic applications

    Science.gov (United States)

    Crane, R. A.; Konstantinou, K. S.

    1988-01-01

    This paper examines three design alternatives for the development of a solar dynamic heat receiver as applied to power systems operating in low earth orbit. These include a base line design used for comparison in ongoing NASA studies, a system incorporating a salt energy storage system with the salt dispersed within a metal mesh and a hybrid system incorporating both a molten salt and molten metal for energy storage. Based on a typical low earth orbit condition, designs are developed and compared to determine the effect of resultant conductivity, heat capacity and heat of fusion on system size, weight, temperature gradients, cycle turbine inlet temperature and material utilization.

  14. 40 CFR 721.640 - Amine substituted metal salts.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amine substituted metal salts. 721.640... Substances § 721.640 Amine substituted metal salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substances identified generically as amine substituted metal salts...

  15. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151) is...

  16. Uranium metal production by molten salt electrolysis

    International Nuclear Information System (INIS)

    Takasawa, Yutaka

    1999-01-01

    Atomic vapor laser isotope separation (AVLIS) is a promising uranium enrichment technology in the next generation. Electrolytic reduction of uranium oxides into uranium metal is proposed for the preparation of uranium metal as a feed material for AVLIS plant. Considering economical performance, continuos process concept and minimizing the amount of radioactive waste, an electrolytic process for producing uranium metal directly from uranium oxides will offer potential advantages over the existing commercial process. Studies of uranium metal by electrolysis in fluoride salts (BaF 2 -LiF-UF 4 (74-11-15 w/o) at 1150-1200degC, using both a laboratory scale apparatus and an engineering scale one, and continuous casting of uranium metal were carried out in order to decide the optimum operating conditions and the design of the industrial electrolytic cells. (author)

  17. Rare earth metals for automotive exhaust catalysts

    International Nuclear Information System (INIS)

    Shinjoh, Hirohumi

    2006-01-01

    The usage of rare earth metals for automotive exhaust catalysts is demonstrated in this paper. Rare earth metals have been widely used in automotive catalysts. In particular, three-way catalysts require the use of ceria compounds as oxygen storage materials, and lanthana as both a stabilizer of alumina and a promoter. The application for diesel catalysts is also illustrated. Effects of inclusion of rare earth metals in automotive catalysts are discussed

  18. Mutual influence of ions of rare earth metals (III) during extraction by trialkylbenzylammonium naphthenates in toluene from multicomponent salt-containing aqueous solutions

    International Nuclear Information System (INIS)

    Pyartman, A.K.; Kopyrin, A.A.; Zhikharev, D.A.; Keskinov, V.A.

    2003-01-01

    Extraction of lanthanide (III) nitrates [Ln(III): Sm-Lu(III), Y] from multicomponent aqua-salt solutions by trialkylbenzylammonium naphthenates in toluene at 298 K and pH 3 is studied. Physicochemical and mathematical models describing distribution and mutual influence of Ln(III) ions in multicomponent solutions in dependence on summary Ln(III) concentration in aqueous phase and concentrate composition are represented with regard to formation of compounds of (R 4 N) 2 [Ln(NO 3 ) 3 A 2 ] (A - fragments of naphthene acids) in organic phase [ru

  19. Rare Earth Metals: Resourcefulness and Recovery

    Science.gov (United States)

    Wang, Shijie

    2013-10-01

    When we appreciate the digital revolution carried over from the twentieth century with mobile communication and the Internet, and when we enjoy our high-tech lifestyle filled with iDevices, hybrid cars, wind turbines, and solar cells in this new century, we should also appreciate that all of these advanced products depend on rare earth metals to function. Although there are only 136,000 tons of annual worldwide demand, (Cho, Rare Earth Metals, Will We Have Enough?)1 rare earth metals are becoming such hot commodities on international markets, due to not only to their increasing uses, including in most critical military hardware, but also to Chinese growth, which accounts for 95% of global rare earth metal production. Hence, the 2013 technical calendar topic, planned by the TMS/Hydrometallurgy and Electrometallurgy Committee, is particularly relevant, with four articles (including this commentary) contributed to the JOM October Issue discussing rare earth metals' resourcefulness and recovery.

  20. Chemoselective single-site Earth-abundant metal catalysts at metal-organic framework nodes.

    Science.gov (United States)

    Manna, Kuntal; Ji, Pengfei; Lin, Zekai; Greene, Francis X; Urban, Ania; Thacker, Nathan C; Lin, Wenbin

    2016-08-30

    Earth-abundant metal catalysts are critically needed for sustainable chemical synthesis. Here we report a simple, cheap and effective strategy of producing novel earth-abundant metal catalysts at metal-organic framework (MOF) nodes for broad-scope organic transformations. The straightforward metalation of MOF secondary building units (SBUs) with cobalt and iron salts affords highly active and reusable single-site solid catalysts for a range of organic reactions, including chemoselective borylation, silylation and amination of benzylic C-H bonds, as well as hydrogenation and hydroboration of alkenes and ketones. Our structural, spectroscopic and kinetic studies suggest that chemoselective organic transformations occur on site-isolated, electron-deficient and coordinatively unsaturated metal centres at the SBUs via σ-bond metathesis pathways and as a result of the steric environment around the catalytic site. MOFs thus provide a novel platform for the development of highly active and affordable base metal catalysts for the sustainable synthesis of fine chemicals.

  1. 40 CFR 721.4620 - Dialkylamino alkanoate metal salt.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Dialkylamino alkanoate metal salt. 721... Substances § 721.4620 Dialkylamino alkanoate metal salt. (a) Chemical substances and significant new uses subject to reporting. (1) The chemical substance identified generically as dialkylamino alkanoate metal...

  2. Recovering heavy rare earth metals from magnet scrap

    Science.gov (United States)

    Ott, Ryan T.; McCallum, Ralph W.; Jones, Lawrence L.

    2017-08-08

    A method of treating rare earth metal-bearing permanent magnet scrap, waste or other material in a manner to recover the heavy rare earth metal content separately from the light rare earth metal content. The heavy rare earth metal content can be recovered either as a heavy rare earth metal-enriched iron based alloy or as a heavy rare earth metal based alloy.

  3. Fundamental study on the salt distillation from the mixtures of rare earth precipitates and LiCl-KCl eutectic salt

    International Nuclear Information System (INIS)

    Yang, H. C.; Eun, H. C.; Cho, Y. Z.; Lee, H. S.; Kim, I. T.

    2008-01-01

    An electrorefining process of spent nuclear fuel generates waste salt containing some radioactive metal chlorides. The most effective method to reduce salt waste volume is to separate radioactive metals from non-radioactive salts. A promising approach is to change radioactive metal chlorides into salt-insoluble oxides by an oxygen sparging. Following this, salt distillation process is available to effectively separate the precipitated particulate metal oxides from salt. This study investigated the distillation rates of LiCl-KCl eutectic salt under different vacuums at elevated temperatures. The first part study investigated distillation rates of eutectic salt under different vacuums at high temperatures by using thermo-gravimetric furnace system. In the second part, we tested the removal of eutectic salt from the RE precipitates by using the laboratory vacuum distillation furnace system. Investigated variables were the temperature of mixture, the degree of vacuum and the time

  4. Alkaline earth metal catalysts for asymmetric reactions.

    Science.gov (United States)

    Kobayashi, Shū; Yamashita, Yasuhiro

    2011-01-18

    The group 2 alkaline earth metals calcium (Ca), strontium (Sr), and barium (Ba) are among the most common elements on Earth, abundant in both the sea and the Earth's crust. Although they are familiar in our daily lives, their application to organic synthesis has, so far, been limited. Some particularly useful properties of these elements include (i) low electronegativity, (ii) a stable oxidation state of +2, meaning that they can potentially form two covalent bonds with anions, and (iii) the ability to occupy a variety of coordination sites due to their large ionic radius. Furthermore, the alkaline earth metals, found between the group 1 and group 3 elements, show mild but significant Lewis acidity, which can be harnessed to control coordinative molecules via a Lewis acid-base interaction. Taken together, these characteristics make the metals Ca, Sr, and Ba very promising components of highly functionalized acid-base catalysts. In this Account, we describe the development of chiral alkaline earth metal catalysts for asymmetric carbon-carbon bond-forming reactions. Recently prepared chiral alkaline earth metal complexes have shown high diastereo- and enantioselectivities in fundamental and important chemical transformations. We chose chiral bisoxazoline (Box) derivatives bearing a methylene tether as a ligand for chiral modification. These molecules are very useful because they can covalently coordinate to alkaline earth metals in a bidentate fashion through deprotonation of the tether portion. It was found that chiral calcium-Box complexes could successfully promote catalytic asymmetric 1,4-addition and [3 + 2] cycloaddition reactions with high diastereo- and enantioselectivities. Both the calcium-Box complexes and chiral strontium-bis-sulfonamide and chiral barium-BINOLate complexes could catalyze asymmetric 1,4-addition reactions with high enantioselectivities. Furthermore, we designed a calcium-neutral coordinative ligand complex as a new type of chiral alkaline

  5. Alkali metal and alkali earth metal gadolinium halide scintillators

    Science.gov (United States)

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  6. Sol-gel processing with inorganic metal salt precursors

    Science.gov (United States)

    Hu, Zhong-Cheng

    2004-10-19

    Methods for sol-gel processing that generally involve mixing together an inorganic metal salt, water, and a water miscible alcohol or other organic solvent, at room temperature with a macromolecular dispersant material, such as hydroxypropyl cellulose (HPC) added. The resulting homogenous solution is incubated at a desired temperature and time to result in a desired product. The methods enable production of high quality sols and gels at lower temperatures than standard methods. The methods enable production of nanosize sols from inorganic metal salts. The methods offer sol-gel processing from inorganic metal salts.

  7. On the capacity to the complexing of alkaline earth metal and magnesium chromates

    International Nuclear Information System (INIS)

    Orekhov, O.L.

    1978-01-01

    Considered is the capacity to the complexing of magnesium chromates and alkaline earth metal chromates with ammonium chromates in aqueous solutions. It has been established that the complexing of alkaline earth metal and magnesium chromates is effected by a nature of initial salts as well as their solubilities and the presence of crystallization water. Capacity of magnesium ions and alkaline rare earth metals to the complexing decreases in a series of Mg-Ca-Sr-Ba. Ca complexes exceed magnesium derivatives in respect of stability

  8. Determination of toxic metals in salt deposits in Bormanda, Nigeria ...

    African Journals Online (AJOL)

    lawal

    Heavy metals which may co-exist with soil salt, when present above their threshold levels could be hazardous to the body system. Common salt samples extracted from soil samples from Bormanda and. Karim Lamido Local Government Areas in Taraba State, Nigeria, were digested in aqua-regia and analysed for Lead ...

  9. Molten Metal Treatment by Salt Fluxing with Low Environmental Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Yogeshwar Sahai

    2007-07-31

    Abstract: Chlorine gas is traditionally used for fluxing of aluminum melt for removal of alkali and alkaline earth elements. However this results in undesirable emissions of particulate matter and gases such as HCl and chlorine, which are often at unacceptable levels. Additionally, chlorine gas is highly toxic and its handling, storage, and use pose risks to employees and the local community. Holding of even minimal amounts of chlorine necessitates extensive training for all plant employees. Fugitive emissions from chlorine usage within the plant cause accelerated corrosion of plant equipment. The Secondary Aluminum Maximum Achievable Control Technology (MACT) under the Clean Air Act, finalized in March 2000 has set very tough new limits on particulate matter (PM) and total hydrogen chloride emissions from aluminum melting and holding furnaces. These limits are 0.4 and 0.1 lbs per ton of aluminum for hydrogen chloride and particulate emissions, respectively. Assuming new technologies for meeting these limits can be found, additional requirements under the Clean Air Act (Prevention of Significant Deterioration and New Source Review) trigger Best Available Control Technology (BACT) for new sources with annual emissions (net emissions not expressed per ton of production) over specified amounts. BACT currently is lime coated bag-houses for control of particulate and HCl emissions. These controls are expensive, difficult to operate and maintain, and result in reduced American competitiveness in the global economy. Solid salt fluxing is emerging as a viable option for the replacement of chlorine gas fluxing, provided emissions can be consistently maintained below the required levels. This project was a cooperative effort between the Ohio State University and Alcoa to investigate and optimize the effects of solid chloride flux addition in molten metal for alkali impurity and non-metallic inclusion removal minimizing dust and toxic emissions and maximizing energy

  10. Effects of metal salt catalysts on yeast cell growth in ethanol conversion

    Science.gov (United States)

    Chung-Yun Hse; Yin Lin

    2009-01-01

    The effects of the addition of metal salts and metal salt-catalyzed hydrolyzates on yeast cell growth in ethanol fermentation were investigated. Four yeast strains (Saccharomyces cerevisiae WT1, Saccharomyces cerevisiae MT81, Candida sp. 1779, and Klumaromyces fragilis), four metal salts (CuCl2, FeCl3, AgNO3, and I2), two metal salt-catalyzed hydrolyzates (...

  11. Molten salt/metal extractions for recovery of transuranic elements

    International Nuclear Information System (INIS)

    Chow, L.S.; Basco, J.K.; Ackerman, J.P.; Johnson, T.R.

    1992-01-01

    The integral fast reactor (EFR) is an advanced reactor concept that incorporates metallic driver and blanket fuels, an inherently safe, liquid-sodium-cooled, pool-type, reactor design, and on-site pyrochemical reprocessing (including electrorefining) of spent fuels and wastes. This paper describes a pyrochemical method that is being developed at Argonne National Laboratory to recover transuranic elements from the EFR electrorefiner process salt. The method uses multistage extractions between molten chloride salts and cadmium metal at high temperatures. The chemical basis of the salt extraction method, the test equipment, and a test plan are discussed

  12. Nonmetal-metal transition in metal–molten-salt solutions

    NARCIS (Netherlands)

    Silvestrelli, P.-L.; Alavi, A.; Parrinello, M.; Frenkel, D.

    1996-01-01

    The method of ab initio molecular dynamics, based on finite-temperature density-functional theory, is used to study the nonmetal-metal transition in two different metal–molten-salt solutions, Kx(KCl)1-x and Nax(NaBr)1-x. As the excess metal concentration is increased the electronic density becomes

  13. Determination of Heavy Metal Levels in Edible Salt

    Directory of Open Access Journals (Sweden)

    Heshmati

    2014-09-01

    Full Text Available Background Edible salt is the most commonly used food additive worldwide. Therefore, any contamination of table salt could be a health hazard. Objectives The present study aimed to determine the levels of heavy metals in table and bakery refined salts. Materials and Methods Eighty-one table refined salt samples and the same number of bakery refined salt samples were purchased from retail market in the province of Hamadan, Iran. The levels of lead (Pb, cadmium (Cd, mercury (Hg, copper (Cu, and iron (Fe were determined using atomic absorption spectroscopy method. Results The levels (mean ± SD, μg/g of Pb, Cd, Hg, Cu, Fe in table refined salt samples were 0.852 ± 0.277, 0.229 ± 0.012, 0.054 ± 0.040, 1.25 ± 0.245 and 0.689 ± 1.58, respectively. The results for the same metals in bakery refined salt samples were as follows (mean ± SD, μg/g: 22 ± 0.320 for Pb, 0.240 ± 0.018 for Cd, 0.058 ± 0.007 for Hg, 1.89 ± 0.218 for Cu, and 8.75 ± 2.10 for Fe. Heavy metal concentrations were generally higher in bakery refined salt. Conclusions The results obtained in the present study were compared with the literature and legal limits. All values for these metals in the table and bakery refined salts were lower than the permitted consumption level defined by Codex (2 µg/g of Pb, 0.5 µg/g of Cd, 0.1 µg/g of Hg, and 2 µg/g of Cu.

  14. Rare earth and zinc layered hydroxide salts intercalated with the 2-aminobenzoate anion as organic luminescent sensitizer

    Energy Technology Data Exchange (ETDEWEB)

    Cursino, Ana Cristina Trindade, E-mail: anacursino@ufpr.br [CEPESQ – Research Centre of Applied Chemistry, Department of Chemistry, Universidade Federal do Paraná – P.O. Box 19081, 81531-980 Curitiba, PR (Brazil); Rives, Vicente, E-mail: vrives@usal.es [GIR-QUESCAT – Department of Inorganic Chemistry, Universidad de Salamanca, Plaza de la Merced S/N, 37998 Salamanca (Spain); Arizaga, Gregorio Guadalupe Carbajal, E-mail: gregoriocarbajal@yahoo.com.mx [Universidad de Guadalajara, Department of Chemistry, Boulevard Marcelino García Barragán 1421, C.P. 44430 Guadalajara, Jalisco (Mexico); Trujillano, Raquel, E-mail: rakel@usal.es [GIR-QUESCAT – Department of Inorganic Chemistry, Universidad de Salamanca, Plaza de la Merced S/N, 37998 Salamanca (Spain); Wypych, Fernando, E-mail: wypych@ufpr.br [CEPESQ – Research Centre of Applied Chemistry, Department of Chemistry, Universidade Federal do Paraná – P.O. Box 19081, 81531-980 Curitiba, PR (Brazil)

    2015-10-15

    Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The UV absorption ability was improved after intercalation/grafting in relation to that shown by the parent material. - Highlights: • Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide were synthesized. • Intercalated nitrate anions were exchanged by 2-aminobenzoate. • In all the 2-aminobenzoate containing compounds, the grafting reaction was detected. • The UV absorption ability was improved after the exchange reactions. • Rare earth hydroxide salts are potential matrixes to produce luminescent materials. - Abstract: Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The obtained compounds were characterized by powder X-ray diffraction (PXRD), Fourier transform infrared (FTIR) and ultraviolet visible (UV–vis) spectroscopies, fluorescence measurements and thermal analysis (TGA/DTA). The results from FTIR spectroscopy suggest a direct coordination of 2-aminobenzoate to the metal cations of the inorganic layered structure. The organic derivative products from the intercalation reactions absorb a broader range of UV-light in relation to that shown by the parent material; the photoluminescence measurements present a strong violet, blue and green luminescence under UV-light excitation for layered compounds with, Zn, Y and Tb, respectively. Rare earth hydroxide salts (RE-LHS) are potential alternative matrices for the immobilization of organic species to produce luminescent materials.

  15. Rare earth and zinc layered hydroxide salts intercalated with the 2-aminobenzoate anion as organic luminescent sensitizer

    International Nuclear Information System (INIS)

    Cursino, Ana Cristina Trindade; Rives, Vicente; Arizaga, Gregorio Guadalupe Carbajal; Trujillano, Raquel; Wypych, Fernando

    2015-01-01

    Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The UV absorption ability was improved after intercalation/grafting in relation to that shown by the parent material. - Highlights: • Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide were synthesized. • Intercalated nitrate anions were exchanged by 2-aminobenzoate. • In all the 2-aminobenzoate containing compounds, the grafting reaction was detected. • The UV absorption ability was improved after the exchange reactions. • Rare earth hydroxide salts are potential matrixes to produce luminescent materials. - Abstract: Rare earth (RE = Eu, Y and Tb) and zinc layered hydroxide salts intercalated with nitrate anions were synthesized, followed by exchange with 2-aminobenzoate. The obtained compounds were characterized by powder X-ray diffraction (PXRD), Fourier transform infrared (FTIR) and ultraviolet visible (UV–vis) spectroscopies, fluorescence measurements and thermal analysis (TGA/DTA). The results from FTIR spectroscopy suggest a direct coordination of 2-aminobenzoate to the metal cations of the inorganic layered structure. The organic derivative products from the intercalation reactions absorb a broader range of UV-light in relation to that shown by the parent material; the photoluminescence measurements present a strong violet, blue and green luminescence under UV-light excitation for layered compounds with, Zn, Y and Tb, respectively. Rare earth hydroxide salts (RE-LHS) are potential alternative matrices for the immobilization of organic species to produce luminescent materials

  16. Neutral alkaline-metal and alkaline-earth-metal derivatives of imidazole and benzimidazole.

    Science.gov (United States)

    Blanco, Fernando; Lloyd, David G; Alkorta, Ibon; Elguero, José

    2014-06-12

    A theoretical study of the minima and connecting transition states of the neutral complexes formed by alkaline-metal and alkaline-earth-metal derivatives of imidazolate and benzimidazolate anions has been carried out using B3LYP/6-31+G(d,p), B3LYP/6-311+G(3df,2p), and G3B3 methods. Two and three nondegenerated minima and two and four TS structures have been identified for imidazole and benzimidazole derivatives, respectively. The most stable minima of the alkaline-metal derivatives of both systems correspond to the metal interacting with the imidazole ring, whereas in the alkaline-earth-metal derivatives, the preferred minima depend on the substituent. A remarkable feature of some minima is the fact that some of the metal-aromatic interactions follow the classical π-cation pattern, even though the global structure corresponds to a neutral salt, constituting a class of noncovalent interaction of great interest in the chemistry of aromatic and heterocyclic complexes. A CSD search has confirmed that the two bonding modes, N-σ and π, are present in the solid phase. The π mode has been analyzed by comparison with other azoles.

  17. Cotton fabrics with UV blocking properties through metal salts deposition

    International Nuclear Information System (INIS)

    Emam, Hossam E.; Bechtold, Thomas

    2015-01-01

    Graphical abstract: - Highlights: • Introducing metal salt based UV-blocking properties into cotton fabric. • A quite simple technique used to produce wash resistant UV-absorbers using different Cu-, Zn- and Ti-salts. • Good UPF was obtained after treatment with Cu and Ti salts, and ranged between 11.6 and 14. • The efficiency of the deposited metal oxides is compared on molar basis. - Abstract: Exposure to sunlight is important for human health as this increases the resistance to diverse pathogens, but the higher doses cause skin problems and diseases. Hence, wearing of sunlight protective fabrics displays a good solution for people working in open atmosphere. The current study offered quite simple and technically feasible ways to prepare good UV protection fabrics based on cotton. Metal salts including Zn, Cu and Ti were immobilized into cotton and oxidized cotton fabrics by using pad-dry-cure technique. Metal contents on fabrics were determined by AAS; the highest metal content was recorded for Cu-fabric and it was 360.6 mmol/kg after treatment of oxidized cotton with 0.5 M of copper nitrate. Ti contents on fabrics were ranged between 168.0 and 200.8 mmol/kg and it showed the lowest release as only 38.1–46.4% leached out fabrics after five laundry washings. Metal containing deposits were specified by scanning electron microscopy and energy dispersive X-ray spectroscopy. UV-transmission radiation over treated fabrics was measured and ultraviolet protection factor (UPF) was calculated. UPF was enhanced after treatment with Cu and Ti salts to be 11.6 and 14, respectively. After five washings, the amount of metal (Cu or Ti) retained indicates acceptable laundering durability.

  18. Rare earth metals, rare earth hydrides, and rare earth oxides as thin films

    International Nuclear Information System (INIS)

    Gasgnier, M.

    1980-01-01

    The review deals with pure rare earth materials such as rare earth metals, rare earth hydrides, and rare earth oxides as thin films. Several preparation techniques, control methods, and nature of possible contaminations of thin films are described. These films can now be produced in an extremely well-known state concerning chemical composition, structure and texture. Structural, electric, magnetic, and optical properties of thin films are studied and discussed in comparison with the bulk state. The greatest contamination of metallic rare earth thin films is caused by reaction with hydrogen or with water vapour. The compound with an f.c.c. structure is the dihydride LnH 2 (Ln = lanthanides). The oxygen contamination takes place after annealing at higher temperatures. Then there appears a compound with a b.c.c. structure which is the C-type sesquioxide C-Ln 2 O 3 . At room atmosphere dihydride light rare earth thin films are converted to hydroxide Ln(OH) 3 . For heavy rare earth thin films the oxinitride LnNsub(x)Osub(y) is observed. The LnO-type compound was never seen. The present review tries to set the stage anew for the investigations to be undertaken in the future especially through the new generations of electron microscopes

  19. Experimental Investigations into U/TRU Recovery using a Liquid Cadmium Cathode and Salt Containing High Rare Earth Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Shelly X. Li; Steven D. Herrmann; Michael F. Simpson

    2009-09-01

    Experimental Investigations into U/TRU Recovery using a Liquid Cadmium Cathode and Salt Containing High Rare Earth Concentrations Shelly X. Li, Steven D. Herrmann, and Michael F. Simpson Pyroprocessing Technology Department Idaho National Laboratory P.O. Box 1625, Idaho Falls, ID 83415 USA Abstract - A series of six bench-scale liquid cadmium cathode (LCC) tests was performed to obtain basic separation data with focus on the behavior of rare earth elements. The electrolyte used for the tests was a mixed salt from the Mk-IV and Mk-V electrorefiners, in which spent metal fuels from Experimental Breeder Reactor-II (EBR-II) had been processed. Rare earth (RE) chlorides, such as NdCl3, CeCl3, LaCl3, PrCl3, SmCl3, and YCl3, were spiked into the salt prior to the first test to create an extreme case for investigating rare earth contamination of the actinides collected by a LCC. For the first two LCC tests, an alloy with the nominal composition of 41U-30Pu-5Am-3Np-20Zr-1RE was loaded into the anode baskets as the feed material. The anode feed material for Runs 3 to 6 was spent ternary fuel (U-19Pu-10Zr). The Pu/U ratio in the salt varied from 0.6 to 1.3. Chemical and radiochemical analytical results confirmed that U and transuranics can be collected into the LCC as a group under the given run conditions. The RE contamination level in the LCC product was up to 6.7 wt% of the total metal collected. The detailed data for partitioning of actinides and REs in the salt and Cd phases are reported in the paper.

  20. Aging of trivalent metal hydroxide/oxide gels in divalent metal salt ...

    Indian Academy of Sciences (India)

    Unknown

    Aging of trivalent metal hydroxide/oxide gels in divalent metal salt solutions: Mechanism of formation of layered double hydroxides (LDHs). A V RADHA and P ..... This situation promotes coprecipitation of the two metal hydroxides, by virtue of which the titrations yield the. Zn–Al LDH. The LDHs isolated before and after ...

  1. Process to separate alkali metal salts from alkali metal reacted hydrocarbons

    Science.gov (United States)

    Gordon, John Howard; Alvare, Javier; Larsen, Dennis; Killpack, Jeff

    2017-06-27

    A process to facilitate gravimetric separation of alkali metal salts, such as alkali metal sulfides and polysulfides, from alkali metal reacted hydrocarbons. The disclosed process is part of a method of upgrading a hydrocarbon feedstock by removing heteroatoms and/or one or more heavy metals from the hydrocarbon feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase containing alkali metal salts and reduced heavy metals, and an upgraded hydrocarbon feedstock. The inorganic phase may be gravimetrically separated from the upgraded hydrocarbon feedstock after mixing at a temperature between about 350.degree. C. to 400.degree. C. for a time period between about 15 minutes and 2 hours.

  2. Melting of Uranium Metal Powders with Residual Salts

    International Nuclear Information System (INIS)

    Jin-Mok Hur; Dae-Seung Kang; Chung-Seok Seo

    2007-01-01

    The Advanced Spent Fuel Conditioning Process (ACP) of the Korea Atomic Energy Research Institute focuses on the conditioning of Pressurized Water Reactor spent oxide nuclear fuel. After the oxide reduction step of the ACP, the resultant metal powders containing ∼ 30 wt% residual LiCl-Li 2 O should be melted for a consolidation of the fine metal powders. In this study, we investigated the melting behaviors of uranium metal powders considering the effects of a LiCl-Li 2 O residual salt. (authors)

  3. Chemoselective single-site Earth-abundant metal catalysts at metal–organic framework nodes

    Energy Technology Data Exchange (ETDEWEB)

    Manna, Kuntal; Ji, Pengfei; Lin, Zekai; Greene, Francis X.; Urban, Ania; Thacker, Nathan C.; Lin, Wenbin (UC)

    2016-08-30

    Earth-abundant metal catalysts are critically needed for sustainable chemical synthesis. Here we report a simple, cheap and effective strategy of producing novel earth-abundant metal catalysts at metal–organic framework (MOF) nodes for broad-scope organic transformations. The straightforward metalation of MOF secondary building units (SBUs) with cobalt and iron salts affords highly active and reusable single-site solid catalysts for a range of organic reactions, including chemoselective borylation, silylation and amination of benzylic C–H bonds, as well as hydrogenation and hydroboration of alkenes and ketones. Our structural, spectroscopic and kinetic studies suggest that chemoselective organic transformations occur on site-isolated, electron-deficient and coordinatively unsaturated metal centres at the SBUs via σ-bond metathesis pathways and as a result of the steric environment around the catalytic site. MOFs thus provide a novel platform for the development of highly active and affordable base metal catalysts for the sustainable synthesis of fine chemicals.

  4. 40 CFR 721.4680 - Metal salts of complex inorganic oxyacids (generic name).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Metal salts of complex inorganic... New Uses for Specific Chemical Substances § 721.4680 Metal salts of complex inorganic oxyacids... substances identified generically as metal salts of complex inorganic oxyacids (PMNs P-89-576 and P-89-577...

  5. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting under...

  6. Optical absorption of dilute solutions of metals in molten salts

    Energy Technology Data Exchange (ETDEWEB)

    Senatore, G.; Parrinello, M.; Tosi, M.P. (Trieste Univ. (Italy). Ist. di Fisica Teorica; Gruppo Nazionale di Struttura dell material del CNR, Trieste (Italy); International Centre for Theoretical Physics, Trieste (Italy))

    1978-12-23

    The theory of liquid structure for fluids of charged hard spheres is applied to an evaluation of the F-centre model for valence electrons in metal-molten salt solutions at high dilution. Minimization of the free energy yields the groundstate radius of the elctron bubble and hence the optical excitation energy in a Franck-Condon transition, the shift and broadening of the transition due to fluctuations in the bubble radius, the volume of mixing, and the activity of the salt in the solution.

  7. Rare Earth Electrochemical Property Measurements and Phase Diagram Development in a Complex Molten Salt Mixture for Molten Salt Recycle

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Jinsuo; Guo, Shaoqiang

    2018-03-30

    Pyroprocessing is a promising alternative for the reprocessing of used nuclear fuel (UNF) that uses electrochemical methods. Compared to the hydrometallurgical reprocessing method, pyroprocessing has many advantages such as reduced volume of radioactive waste, simple waste processing, ability to treat refractory material, and compatibility with fast reactor fuel recycle. The key steps of the process are the electro-refining of the spent metallic fuel in the LiCl-KCl eutectic salt, which can be integrated with an electrolytic reduction step for the reprocessing of spent oxide fuels. During the electro-refining process, actinides and active fission products such rare earth (RE) elements are dissolved into the molten salt from the spent fuel at an anode basket. Then U and Pu are electro-deposited on the cathodes while REs with relatively negative reduction potentials are left in the molten salt bath. However, with the accumulation of lanthanides in the salt, the reduction potentials of REs will approach the values for U and Pu, affecting the recovery efficiency of U and Pu. Hence, RE drawdown is necessary to reduce salt waste after uranium and minor actinides recovery, which can also be performed by electrochemical separations. To separate various REs and optimize the drawdown process, physical properties of REs in LiCl-KCl salt and their concentration dependence are essential. Thus, the primary goal of present research is to provide fundamental data of REs and deduce phase diagrams of LiCl-KCl-RECl3 based complex molten salts. La, Nd and Gd are three representative REs that we are particularly interested in due to the high ratio of La and Nd in UNF, highest standard potential of Gd among all REs, and the existing literature data in dilute solution. Electrochemical measurements are performed to study the thermodynamics and transport properties of LaCl3, GdCl3, NdCl3, and NdCl2 in LiCl-KCl eutectic in the temperature range 723-823 K. Test are conducted in LiCl-KCl melt

  8. The nonmetal-metal transition in solutions of metals in molten salts

    International Nuclear Information System (INIS)

    Tosi, M.P.

    1997-04-01

    Solutions of metals in molten salts present a rich phenomenology: localization of electrons in disordered ionic media, activated electron transport increasing with metal concentration towards a nonmetal-metal (NM-M) transition, and liquid-liquid phase separation. A brief review of progress in the study of these systems is given in this article, with main focus on the NM-M transition. After recalling the known NM-M behaviour of the component elements in the case of expanded fluid alkali metals and mercury and of solid halogens under pressure, the article focuses on liquid metal - molten salt solutions and traces the different NM-M behaviours of the alkalis in their halides and of metals added to polyvalent metal halides. (author). 51 refs, 2 figs

  9. Fate and effects of heavy metals in salt marsh sediments

    Energy Technology Data Exchange (ETDEWEB)

    Suntornvongsagul, Kallaya [Department of Chemical Engineering, New Jersey Institute of Technology (NJIT), University Heights, Newark, NJ 07102 (United States); Environmental Research Institute, Chulalongkorn University, Phayathai Road, Pathumwan, Bangkok 10330 (Thailand); Burke, David J. [Department of Biological Sciences, Rutgers University, 101 Warren Street, Smith Hall 135, Newark, NJ 07102 (United States); The Holden Arboretum, 9500 Sperry Road, Kirtland, OH 44094 (United States); Hamerlynck, Erik P. [Department of Biological Sciences, Rutgers University, 101 Warren Street, Smith Hall 135, Newark, NJ 07102 (United States); Hahn, Dittmar [Department of Chemical Engineering, New Jersey Institute of Technology (NJIT), University Heights, Newark, NJ 07102 (United States) and Department of Biology, Texas State University, 601 University Drive, San Marcos, TX 78666 (United States)]. E-mail: dh49@txstate.edu

    2007-09-15

    The fate and effects of selected heavy metals were examined in sediment from a restored salt marsh. Sediment cores densely covered with Spartina patens were collected and kept either un-amended or artificially amended with nickel (Ni) under standardized greenhouse conditions. Ni-amendment had no significant effect on the fate of other metals in sediments, however, it increased root uptake of the metals. Metal translocation into the shoots was small for all metals. Higher Ni concentrations in plants from amended cores were accompanied by seasonal reductions in plant biomass, photosynthetic capacity and transfer efficiency of open photosystem II reaction centers; these effects, however, were no longer significant at the end of the growing season. Root colonization by arbuscular mycorrhizal fungi (AMF) resembled that of natural salt marshes with up to 20% root length colonized. Although Ni-amendment increased AMF colonization, especially during vegetative growth, in general AMF were largely unaffected. - Spartina patens accumulates heavy metals in roots without significant translocation into shoots, and with only small seasonal effects on plant growth performance and mycorrhizal colonization.

  10. Applications of molten salts in reactive metals processing

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, B.; Olson, D.L. [Colorado School of Mines, Golden, CO (United States). Kroll Inst. for Extractive Metallurgy; Averill, W.A. [EG and G Rocky Flats, Inc., Golden, CO (United States). Rocky Flats Plant

    1993-12-31

    Pyrochemical processes using molten salts provide a unique opportunity for the extraction and refining of many reactive and valuable metals either directly from the beneficiated ore or from other process effluent that contain reactive metal compounds. This research program is aimed at developing a process for the production and recovery of reactive and valuable metals, such as zinc, tin, lead, bismuth and silver, in a hybrid reactor combining electrolytic production of the calcium reductant and in-situ utilization of this reductant for pyrochemical reduction of the metal compounds, such as halide or oxides. The process is equally suitable for producing other low melting metals, such as cadmium and antimony. The cell is typically operated below 1000C temperature. Attempts have been made to produce silver, lead, bismuth, tin and cerium by calciothermic reduction in a molten salt media. In a separate effort, calcium has been produced by an electrolytic dissociation of lime in a calcium chloride medium. The most important characteristic of the hybrid technology is its ability to produce metals under ``zero-waste`` conditions.

  11. Application of molten salts in pyrochemical processing of reactive metals

    International Nuclear Information System (INIS)

    Mishra, B.; Olson, D.L.; Averill, W.A.

    1992-01-01

    Various mixes of chloride and fluoride salts are used as the media for conducting pyrochemical processes in the production and purification of reactive metals. These processes generate a significant amount of contaminated waste that has to be treated for recycling or disposal. Molten calcium chloride based salt systems have been used in this work to electrolytically regenerate calcium metal from calcium oxide for the in situ reduction of reactive metal oxides. The recovery of calcium is characterized by the process efficiency to overcome back reactions in the electrowinning cell. A thermodynamic analysis, based on fundamental rate theory, has been performed to understand the process parameters controlling the metal deposition, rate, behavior of the ceramic anode-sheath and influence of the back-reactions. It has been observed that the deposition of calcium is dependent on the ionic diffusion through the sheath. It has also been evidenced that the recovered calcium is completely lost through the back-reactions in the absence of a sheath. A practical scenario has also been presented where the electrowon metal can be used in situ as a reductant to reduce another reactive metal oxide

  12. Syntheses and structures of new rare-earth metal tetracyanidoborates

    Energy Technology Data Exchange (ETDEWEB)

    Falk, Fanni; Hackbarth, Liisa; Koeckerling, Martin [Anorganische Festkoerperchemie, Institut fuer Chemie, Universitaet Rostock, Albert-Einstein-Str. 3a, 18059, Rostock (Germany); Herkert, Lorena; Mueller-Buschbaum, Klaus; Finze, Maik [Institut fuer Anorganische Chemie, Institut fuer nachhaltige Chemie and Katalyse mit Bor (ICB), Julius-Maximilians-Universitaet Wuerzburg, Am Hubland, 97074, Wuerzburg (Germany)

    2017-05-04

    Six new rare-earth metal tetracyanidoborates were prepared and characterized by single-crystal X-ray diffraction. Crystals of these salts contain co-crystallized solvent molecules, such as water, acetone, ethanol, or diethyl ether. In [La(EtOH){sub 3}(H{sub 2}O){sub 2}{B(CN)_4}{sub 3}] (1), [La(EtOH)(H{sub 2}O){sub 4}{B(CN)_4}{sub 3}].Et{sub 2}O (2), and [Y(EtOH)(H{sub 2}O){sub 4}{B(CN)_4}{sub 3}].EtOH (6) the tetracyanidoborate anions are all or in part bonded to the RE{sup 3+} ions, whereas in [Pr(H{sub 2}O){sub 9}][B(CN){sub 4}]{sub 3}.(CH{sub 3}){sub 2}CO (3), [Er(H{sub 2}O){sub 8}][B(CN){sub 4}]{sub 3}.(CH{sub 3}){sub 2}CO (4), and [Lu(EtOH)(H{sub 2}O){sub 7}][B(CN){sub 4}]{sub 3}.EtOH.0.5H{sub 2}O (5) the [B(CN){sub 4}]{sup -} anions are not coordinated to the central metal atoms. Only in 1, one of the three crystallographically independent [B(CN){sub 4}]{sup -} anions acts as a bridging ligand. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Size-selective extraction of metal salts: the general principles

    International Nuclear Information System (INIS)

    Yakshin, V.V.

    1988-01-01

    Consideration is given to application of the structural correspondence principle for explaining processes of selective (with respect to ion size) solvent extraction of metal salts from aqueous solutions to organic phase by crown-ethers of different spatial and electronic structure. A study has been made on more than 50 different structures of cyclic and acyclic polyethers, containing aromatic, aliphatic and cycloaliphatic fragments. It is shown that introduction of additional substituents enables to increase extraction selectivity and separate elements with similar chemical properties

  14. Transgenerational adaptation to heavy metal salts in Arabidopsis

    Directory of Open Access Journals (Sweden)

    Mohammad eReza Rahavi

    2011-12-01

    Full Text Available Exposure to abiotic and biotic stress results in changes in plant physiology and triggers genomic instability. Recent reports suggest that the progeny of stressed plants also exhibit changes in genome stability, stress tolerance and methylation.Here we analyzed whether exposure to Ni2+, Cd2+ and Cu2+ salts leads to transgenerational changes in the homologous recombination frequency and in the stress tolerance. We found that immediate progeny of stressed plants indeed exhibit increased recombination frequency. When the progeny of stressed plants was propagated without stress, the recombination frequency changed back to normal. Exposure of plants to heavy metals for five consecutive generations (S1-S5 showed that recombination frequency was maintained at high level. Skipping stress after propagation on 50 mM Ni2+ or Cd2+ for 2-3 generations did not decrease the recombination frequency, suggesting certain acclimation to upregulated recombination. Analysis of the progeny of plants exposed to Cu2+ and Ni2+ showed that the plants had higher stress tolerance to the same heavy metal salts. The tolerance was higher in plants propagated on stress for 3-5 generations, which had longer roots than plants propagated on heavy metals only for 1-2 generations. Also the tolerance was more prominent upon exposure to higher concentration of salts. The progeny of stressed plants was also more tolerant to NaCl and MMS.

  15. Actinides recovery from molten salt/liquid metal system by electrochemical methods

    Science.gov (United States)

    Iizuka, Masatoshi; Koyama, Tadafumi; Kondo, Naruhito; Fujita, Reiko; Tanaka, Hiroshi

    1997-08-01

    Electrochemical methods were examined for the recovery of actinides from the electrorefiner which is used in pyrometallurgical reprocessing of spent metal fuel for fast reactors. Uranium was successfully collected at the solid steel cathode from both liquid cadmium and molten salt solvents. In electrotransport from liquid cadmium, the behavior of uranium and rare earths was as expected by a computer simulation code based on the diffusion layer model at the interface between the electrolyte and the electrodes. In electroreduction from the molten salt electrolyte, a considerable amount of uranium was reduced at the CdLi anode by direct chemical reduction with lithium, especially at a lower anodic current density. The decrease in collection efficiency of uranium due to the direct chemical reduction would be avoided by maintaining the anode potential higher than the deposition potential of uranium.

  16. Electrochemical Extraction of Rare Earth Metals in Molten Fluorides : Conversion of Rare Earth Oxides into Rare Earth Fluorides Using Fluoride Additives

    NARCIS (Netherlands)

    Abbasalizadeh, A.; Malfliet, Annelies; Seetharaman, Seshadri; Sietsma, J.; Yang, Y.

    2017-01-01

    In the present research on rare earth extraction from rare earth oxides (REOs), conversion of rare earth oxides into rare earth fluorides with fluoride fluxes is investigated in order to overcome the problem of low solubility of the rare earth oxides in molten fluoride salts as well as the formation

  17. Enhancing Skin Permeation of Biphenylacetic Acid (BPA) Using Salt Formation with Organic and Alkali Metal Bases

    OpenAIRE

    PAWAR, Vijay; NAIK, Prashant; GIRIDHAR, Rajani; YADAV, Mange Ram

    2014-01-01

    In the present study, a series of organic and alkali metal salts of biphenylacetic acid (BPA) have been prepared and evaluated in vitro for percutaneous drug delivery. The physicochemical properties of BPA salts were determined using solubility measurements, DSC, and IR. The DSC thermogram and FTIR spectra confirmed the salt formation with organic and alkali metal bases. Among the series, salts with organic amines (ethanolamine, diethanolamine, triethanol-amine, and diethylamine) had lowered ...

  18. Near-Earth asteroids: Metals occurrence, extraction, and fabrication

    Science.gov (United States)

    Westfall, Richard

    Near-earth asteroids occur in three principle types of orbits: Amor, Apollo, and Aten. Amor asteroids make relatively close (within 0.3 AU) approaches to the earth's orbit, but do not actually overlap it. Apollo asteroids spend most of their time outside the earth's orbital path, but at some point of close approach to the sun, they cross the orbit of the earth. Aten asteroids are those whose orbits remain inside the earth's path for the majority of their time, with semi-major axes less than 0.1 AU. Near-earth orbit asteroids include: stones, stony-irons, irons, carbonaceous, and super-carbonaceous. Metals within these asteroids include: iron, nickel, cobalt, the platinum group, aluminum, titanium, and others. Focus is on the extraction of ferrous and platinum group metals from the stony-iron asteroids, and the iron asteroids. Extraction of the metal fraction can be accomplished through the use of tunnel-boring-machines (TBM) in the case of the stony-irons. The metals within the story-iron asteroids occur as dispersed granules, which can be separated from the stony fraction through magnetic and gaseous digestion separation techniques. The metal asteroids are processes by drilling and gaseous digestion or by gaseous digestion alone. Manufacturing of structures, housings, framing networks, pressure vessels, mirrors, and other products is accomplished through the chemical vapor deposition (CVD) of metal coating on advanced composites and on the inside of contour-defining inflatables (CDI). Metal coatings on advanced composites provide: resistance to degradation in the hostile environments of space; superior optical properties; superior heat dissipation; service as wear coatings; and service as evidential coatings. Metal coatings on the inside of CDI produce metal load-bearing products. Fibers such as graphite, kevlar, glass, ceramic, metal, etc., can be incorporated in the metal coatings on the inside of CDI producing metal matrix products which exhibit high strength

  19. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under this...

  20. Ionic structure of solutions of alkali metals and molten salts

    International Nuclear Information System (INIS)

    Chabrier, G.; Senatore, G.; Tosi, M.P.

    1982-02-01

    Neutron diffraction patterns from K-KCl and Rb-RbBr liquid solutions at various compositions are examined in an ionic-mixture model which neglects screening and aggregation due to the metallic electrons. The main feature of the observed diffraction patterns for wave number k above roughly 1A -1 are accounted for by the model. The approach to the metal-rich end of the phase diagram is analyzed in detail from different viewpoints in the K-KCl system. Short-range correlations of the potassium ions are described in this region by a metallic radius deduced from properties of the pure liquid metal, but a simple expanded-metal model must be supplemented by the assumption that considerable disorder is introduced in its structure by the halogen ions. Features of short-range ordering in the salt-rich region that are implied by a shoulder on the high-k side of the main peak in the diffraction pattern are also commented upon. (author)

  1. Enhancing Skin Permeation of Biphenylacetic Acid (BPA) Using Salt Formation with Organic and Alkali Metal Bases.

    Science.gov (United States)

    Pawar, Vijay; Naik, Prashant; Giridhar, Rajani; Yadav, Mange Ram

    2015-01-01

    In the present study, a series of organic and alkali metal salts of biphenylacetic acid (BPA) have been prepared and evaluated in vitro for percutaneous drug delivery. The physicochemical properties of BPA salts were determined using solubility measurements, DSC, and IR. The DSC thermogram and FTIR spectra confirmed the salt formation with organic and alkali metal bases. Among the series, salts with organic amines (ethanolamine, diethanolamine, triethanolamine, and diethylamine) had lowered melting points while the alkali metal salt (sodium) had a higher melting point than BPA. The in vitro study showed that salt formation improves the physicochemical properties of BPA, leading to improved permeability through the skin. Amongst all the prepared salts, ethanolamine salt (1b) showed 7.2- and 5.4-fold higher skin permeation than the parent drug at pH 7.4 and 5.0, respectively, using rat skin.

  2. Synthesis and infrared spectra of alkaline earth metal carbonates ...

    Indian Academy of Sciences (India)

    Unknown

    investigations deal with the synthesis and characteriza- tion of complexes of urea with transition metals (Penland et al 1957; Schafer and Curran 1966; Barbier and Hugel. 1974, 1977; Srivastava and Aravindakshan 1983). How- ever, studies on the nature of the reaction of urea with alkaline earth metals are very rare and ...

  3. Synthesis and infrared spectra of alkaline earth metal carbonates ...

    Indian Academy of Sciences (India)

    The metal carbonate, MCO3 (M = Ca, Sr and Ba), was synthesized by a novel method of reacting aqueous solution of each of Ca2+, Sr2+ and Ba2+ salts with urea at high temperature, ∼ 80°C. The reaction products were characterized through elemental analysis and infrared spectra. The infrared spectra of the products are ...

  4. Preferential solvation, ion pairing, and dynamics of concentrated aqueous solutions of divalent metal nitrate salts

    Science.gov (United States)

    Yadav, Sushma; Chandra, Amalendu

    2017-12-01

    We have investigated the characteristics of preferential solvation of ions, structure of solvation shells, ion pairing, and dynamics of aqueous solutions of divalent alkaline-earth metal nitrate salts at varying concentration by means of molecular dynamics simulations. Hydration shell structures and the extent of preferential solvation of the metal and nitrate ions in the solutions are investigated through calculations of radial distribution functions, tetrahedral ordering, and also spatial distribution functions. The Mg2+ ions are found to form solvent separated ion-pairs while the Ca2+ and Sr2+ ions form contact ion pairs with the nitrate ions. These findings are further corroborated by excess coordination numbers calculated through Kirkwood-Buff G factors for different ion-ion and ion-water pairs. The ion-pairing propensity is found to be in the order of Mg(NO3) 2 ions which is achieved in the current study through electronic continuum correction force fields. A detailed analysis of the effects of ion-pairs on the structure and dynamics of water around the hydrated ions is done through classification of water into different subspecies based on their locations around the cations or anions only or bridged between them. We have looked at the diffusion coefficients, relaxation of orientational correlation functions, and also the residence times of different subspecies of water to explore the dynamics of water in different structural environments in the solutions. The current results show that the water molecules are incorporated into fairly well-structured hydration shells of the ions, thus decreasing the single-particle diffusivities and increasing the orientational relaxation times of water with an increase in salt concentration. The different structural motifs also lead to the presence of substantial dynamical heterogeneity in these solutions of strongly interacting ions. The current study helps us to understand the molecular details of hydration structure, ion

  5. Rare earths and rare earth alloys electrolytic preparation process and device for this process

    International Nuclear Information System (INIS)

    Seon, F.; Barthole, G.

    1986-01-01

    Electrolysis of a molten salt of rare earth or rare earth alloy for preparation of the metal or alloy is described. The molten salt bath comprises at least a rare earth chloride, at least an alkaline or alkaline earth chloride and at least an alkaline or alkaline earth fluoride [fr

  6. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Science.gov (United States)

    2010-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... Significant New Uses for Specific Chemical Substances § 721.10097 Disubstituted benzenesulfonic acid, alkali... chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN P...

  7. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Disubstituted benzoic acid, alkali... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject to...

  8. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fluorinated carboxylic acid alkali... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under this...

  9. Chronopotentiometry of refractory metals, actinides and oxyanions in molten salts: A review

    Science.gov (United States)

    Bansal, Narottam P.

    1992-01-01

    The applications of chronopotentiometry to the study of electrochemical behavior of three technologically important areas of refractory metals, actinides, and oxyanions in molten salts are critically reviewed. Chronopotentiometry is a very versatile diagnostic tool to understand the reaction mechanism of the electrode processes for the electrochemical reduction/oxidation of these electroactive species in molten salt solutions. Well adherent, compact, and uniformly thick coatings of refractory metals may be electrodeposited from their solutions in molten salts.

  10. Polyoxometalate electrocatalysts based on earth-abundant metals for efficient water oxidation in acidic media

    Science.gov (United States)

    Blasco-Ahicart, Marta; Soriano-López, Joaquín; Carbó, Jorge J.; Poblet, Josep M.; Galan-Mascaros, J. R.

    2018-01-01

    Water splitting is a promising approach to the efficient and cost-effective production of renewable fuels, but water oxidation remains a bottleneck in its technological development because it largely relies on noble-metal catalysts. Although inexpensive transition-metal oxides are competitive water oxidation catalysts in alkaline media, they cannot compete with noble metals in acidic media, in which hydrogen production is easier and faster. Here, we report a water oxidation catalyst based on earth-abundant metals that performs well in acidic conditions. Specifically, we report the enhanced catalytic activity of insoluble salts of polyoxometalates with caesium or barium counter-cations for oxygen evolution. In particular, the barium salt of a cobalt-phosphotungstate polyanion outperforms the state-of-the-art IrO2 catalyst even at pH < 1, with an overpotential of 189 mV at 1 mA cm-2. In addition, we find that a carbon-paste conducting support with a hydrocarbon binder can improve the stability of metal-oxide catalysts in acidic media by providing a hydrophobic environment.

  11. Structural variations in layered alkaline earth metal cyclohexyl ...

    Indian Academy of Sciences (India)

    Administrator

    because of the entrance of the guest molecules between the layers, there will be a change in the interlayer distance (Alberti 1978). Although M(IV) organo-phos- phonates are well documented, the chemistry of M(II) organophosphonates especially the alkaline earth metal organophosphonates has been explored marginally ...

  12. Electrons and Spin Waves in Heavy Rare Earth Metals

    DEFF Research Database (Denmark)

    Mackintosh, A. R.

    1972-01-01

    Although the main principles governing the magnetic interactions and magnetic ordering in rare earth metals have been qualitatively understood for some time, it is only relatively recently that a sufficiently detailed study has been made of their electronic and magnetic excitations to place...

  13. Alkaline-earth metal phenylphosphonates and their intercalation chemistry

    Czech Academy of Sciences Publication Activity Database

    Melánová, Klára; Beneš, L.; Svoboda, J.; Zima, Vítězslav; Pospíšil, M.; Kovář, P.

    2018-01-01

    Roč. 47, č. 9 (2018), s. 2867-2880 ISSN 1477-9226 R&D Projects: GA ČR(CZ) GA17-10639S Institutional support: RVO:61389013 Keywords : intercalation * layered compounds * alkaline-earth metal phenylphosphonates Subject RIV: CA - Inorganic Chemistry OBOR OECD: Inorganic and nuclear chemistry Impact factor: 4.029, year: 2016

  14. Alkaline-earth metal compounds. Oddities and applications

    International Nuclear Information System (INIS)

    Harder, Sjoerd

    2013-01-01

    This book contains the following six topics: heavy alkaline-earth metal organometallic and metal organic chemistry: synthetic methods and properties (Ana Torvisco, Karin Ruhlandt-Senge); Heavier group 2 Grignard reagents of the type aryl-ae(l) n -x post-Grignard reagents (Matthias Westerhausen, Jens Langer, Sven Krieck, Reinald Fischer, Helmar Goerls, Mathias Koehler); stable molecular magnesium(I) dimers: A fundamentally appealing yet synthetically versatile compound class (Cameron Jones, Andreas Stasch); Modern developments in magnesium reagent chemistry for synthesis (Robert E. Mulvey, Stuart D. Robertson); Alkaline-earth metal complexes in homogeneous polymerization catalysis (Jean-Francois Carpentier, Yann Sarazin); homogeneous catalysis with organometallic complexes of group 2 (Mark R. Crimmin, Michael S. Hill); Chiral Ca, Sr and Ba-catalyzed asymmetric direct-type aldol, Michael, and Mannich and related reactions (Tetsu Tsubogo, Yasuhiro Yamashita, Shu- Kobayashi).

  15. Preparation process of an yttrium (or one rare earth), one alkaline earth metal, copper and oxygen superconductive compound

    International Nuclear Information System (INIS)

    Michel, C.; Pham Ai-Qooc; Raveau, B.

    1991-01-01

    The present invention describes the fabrication at atmospheric pressure of a compound based on yttrium (or a rare earth), one alkaline earth metal, copper, and oxygen so as to get a high-tc superconductor material. 2 refs

  16. Molten salt reactors. Synthesis of studies realized between 1973 and 1983. Metallic materials file

    International Nuclear Information System (INIS)

    1983-03-01

    Metallic materials for molten salt reactors are studied. The corrosion of steels by the eutectic LiF-BeF 2 and molten lead is examined. Fabrication, aging and welding of molybdenum or TZM tubes are also examined. [fr

  17. Direct reduction of uranium dioxide and few other metal oxides to corresponding metals by high temperature molten salt electrolysis

    International Nuclear Information System (INIS)

    Mohandas, K.S.

    2017-01-01

    Molten salt based electro-reduction processes, capable of directly converting solid metal oxides to metals with minimum intermediate steps, are being studied worldwide. Production of metals apart, the process assumes importance in nuclear technology in the context of pyrochemical reprocessing of spent oxide fuels, for it serves as an intermediate step to convert spent oxide fuel to a metal alloy, which in turn can be processed by molten salt electro-refining method to gain the actinides present in it. In the context of future metal fuel fast reactor programme, the electrochemical process was studied for conversion of solid UO 2 to U metal in LiCl-1wt.% Li 2 O melt at 650 °C with platinum anode at the Metal Processing Studies Section, PMPD, IGCAR. A brief overview of the work is presented in the paper

  18. Geochemistry of metal-rich brines from central Mississippi Salt Dome basin, U.S.A.

    Science.gov (United States)

    Kharaka, Y.K.; Maest, A.S.; Carothers, W.W.; Law, L.M.; Lamothe, P.J.; Fries, T.L.

    1987-01-01

    Oil-field brines are the most favored ore-forming solutions for the sediment-hosted Mississippi Valley-type ore deposits. Detailed inorganic and organic chemical and isotope analyses of water and gas samples from six oil fields in central Mississippi, one of the very few areas with high metal brines, were conducted to study the inorganic and organic complexes responsible for the high concentrations of these metals. The samples were obtained from production zones consisting of sandstone and limestone that range in depth from 1900 to 4000 m (70-120??C) and in age from Late Cretaceous to Late Jurassic. Results show that the waters are dominantly bittern brines related to the Louann Salt. The brines have extremely high salinities that range from 160,000 to 320,000 mg/l total dissolved solids and are NaCaCl-type waters with very high concentrations of Ca (up to 48,000 mg/l) and other alkaline-earth metals, but with low concentrations of aliphatic acid anions. The concentrations of metals in many water samples are very high, reaching values of 70 mg/l for Pb, 245 mg/l for Zn, 465 mg/l for Fe and 210 mg/l for Mn. The samples with high metal contents have extremely low concentrations (<0.02 mg/l) of H2S. Samples obtained from the Smackover Formation (limestone) have low metal contents that are more typical of oil-field waters, but have very high concentrations (up to 85 mg/l) of H2S. Computations with the geochemical code SOLMINEQ.87 give the following results: (1) both Pb and Zn are present predominantly as aqueous chloride complexes (mainly as PbCl42- and ZnCl42-, respectively); (2) the concentrations of metals complexed with short-chained aliphatic acid anions and reduced S species are minor; (3) organic acid anions are important in controlling the concentrations of metals because they affect the pH and buffer capacity of the waters at subsurface conditions; and (4) galena and sphalerite solubilities control the concentrations of Pb and Zn in these waters. ?? 1988.

  19. Crystal field in rare-earth metals and intermetallic compounds

    International Nuclear Information System (INIS)

    Ray, D.K.

    1978-01-01

    Reasons for the success of the crystal-field model for the rare-earth metals and intermetallic compounds are discussed. A review of some of the available experimental results is made with emphasis on cubic intermetallic compounds. Various sources of the origin of the crystal field in these metals are discussed in the background of the recent APW picture of the conduction electrons. The importance of the non-spherical part of the muffin-tin potential on the single-ion anisotropy is stressed. (author)

  20. Present status of production and utilization of rare earth metals and their compounds

    International Nuclear Information System (INIS)

    Al'perina, E.M.; Tsygankova, G.V.

    1983-01-01

    The status of raw material sources and production of rare earth metals and their compounds abroad is considered. Prices for rare earth raw materials, metals and their compounds are discussed. Special attention is paid to consumption of rare earth metals and their compounds and to perspectives of consumption growth

  1. Electronic Structure of Rare-Earth Metals. II. Positron Annihilation

    DEFF Research Database (Denmark)

    Williams, R. W.; Mackintosh, Allan

    1968-01-01

    The angular correlation of the photons emitted when positrons annihilate with electrons has been studied in single crystals of the rare-earth metals Y, Gd, Tb, Dy, Ho, and Er, and in a single crystal of an equiatomic alloy of Ho and Er. A comparison of the results for Y with the calculations...... of Loucks shows that the independent-particle model gives a good first approximation to the angular distribution, although correlation effects probably smear out some of the structure. The angular distributions from the heavy rare-earth metals are very similar to that from Y and can be understood...... qualitatively in terms of the relativistic augmented-plane-wave calculations by Keeton and Loucks. The angular distributions in the c direction in the paramagnetic phases are characterized by a rapid drop at low angles followed by a hump, and these features are associated with rather flat regions of Fermi...

  2. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

    Science.gov (United States)

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1995-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  3. Vibrational spectra of double rare earth alkaline metal metaphosphates

    International Nuclear Information System (INIS)

    Madij, V.A.; Krasilov, Yu.I.; Kizel', V.A.; Denisov, Yu.V.; Chudinova, N.N.; Vinogradova, N.V.

    1978-01-01

    Joint analysis of the Raman and infrared absorption spectra, as well as X-ray structural data for binary metaphosphates, suggest a cyclic structure of the anion in RbEu(PO 3 ) 4 and a chain structure of the anions in HEu(PO 3 ) 4 and LiEu(PO 3 ) 4 . Spectroscopic criteria are proposed for distinguishing between cyclic and chain structures in binary metaphosphates of rare earth elements and alkali metals

  4. Thermomagnetic marking of rare-earth-transition-metal thin films

    Science.gov (United States)

    Bartholomeusz, Brian Josef

    1989-01-01

    Analytical derivation of temperature profiles in laser-irradiated thin-film structures is hindered by the nature of the heat source terms and by the geometrical complexity that often exists. This study utilizes a combined Laplace-transform-Fourier-integral method to obtain approximate solutions for a number of simple cases. The results are used to study the thermomagnetic marking process in rare-earth-transition-metal (RE-TM) thin films, and the predictions are compared with experimental observations.

  5. Rare metal and rare earth pegmatites of Western India

    International Nuclear Information System (INIS)

    Maithani, P.B.; Nagar, R.K.

    1999-01-01

    Rajasthan Mica Belt in western India is one of the three major mica-producing Proterozoic pegmatite belts of India, the others being in Bihar and Andhra Pradesh. The pegmatites of these mica belts, in general, are associated with the rare metal (RM) and rare earth element (REE)-bearing minerals like columbite-tantalite, beryl, lepidolite and other multiple oxides. RM-REE pegmatites of Gujarat are devoid of commercially workable mica. These pegmatites are geologically characterised in this paper, based on their association with granite plutons geochemistry, and RM and REE potential. In addition to RM and RE-bearing pegmatites, granites of the Umedpur area, Gujarat also show anomalous concentration (0.97 wt%) of rare metals (6431 ppm Nb, 1266 ppm Ta, 454 ppm Sn, 173 ppm W), (1098 ppm Ce 1.36% Y 2 O 3 ) rare earths, and uranium (0.40% eU 3 O 8 ). Eluvial concentrations in the soil and panned concentrate (0.04-0.28 wt%) analysed up to 7.4%Nb 2 O 5 , 836 ppm Ta, and 1.31% Y. Discrete columbite-tantalite and betafite have been identified in these concentrates in addition to other minerals like zircon, rutile, sphene and xenotime. This area with discrete RM R EE mineral phases could be significant as a non-pegmatite source for rare metal and rare earths. (author)

  6. Soluble salts: their incidence on the protection of metallic structures by paint coatings

    International Nuclear Information System (INIS)

    Morcillo, M.

    2003-01-01

    The presence of soluble salts at the metal/paint interface is known to have a detrimental effect on the integrity of most paint systems. Though this is a long-standing problem, it has recently come to receive greater attention from the protective coatings industry. In the paper the following points are reviewed: degradation mechanisms of the metal/paint system, the role of the metallic substrate, the nature, origin and detection os soluble salts, expected levels of soluble salts in practice, critical thresholds of soluble salts and risk levels for premature failures, role of the type and thickness of paint systems and exposure conditions, and prevention measures. The author presents an overview of the subject, making reference to the related research that has been carried out by him and his co-workers over the last 16 years. (Author) 58 refs

  7. Shape-controlled syntheses of metal oxide nanoparticles by the introduction of rare-earth metals.

    Science.gov (United States)

    Song, Hyo-Won; Kim, Na-Young; Park, Ji-Eun; Ko, Jae-Hyeon; Hickey, Robert J; Kim, Yong-Hyun; Park, So-Jung

    2017-02-23

    Here, we report the size- and shape-controlled synthesis of metal oxide nanoparticles through the introduction of rare-earth metals. The addition of gadolinium oleate in the synthesis of iron oxide nanoparticles induced sphere-to-cube shape changes of nanoparticles and generated iron oxide nanocubes coated with gadolinium. Based on experimental investigations and density functional theory (DFT) calculations, we attribute the shape change to the facet-selective binding of undecomposed gadolinium oleates. While many previous studies on the shape-controlled syntheses of nanoparticles rely on the stabilization of specific crystal facets by anionic surfactants or their decomposition products, this study shows that the interaction between growing transition metal oxide nanoparticles and rare-earth metal complexes can be used as a robust new mechanism for shape-controlled syntheses. Indeed, we demonstrated that this approach was applicable to other transition metal oxide nanoparticles (i.e., manganese oxide and manganese ferrite) and rare earth metals (i.e., gadolinium, europium, and cerium). This study also demonstrates that the nature of metal-ligand bonding can play an important role in the shape control of nanoparticles.

  8. Surface tension of light rare earth fluoride molten salts electrolyte system

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Xiaoping [School of Materials & Metallurgy, Northeastern University, Shenyang 110819 (China); Sun, Shuchen, E-mail: sunsc@smm.neu.edu.cn [School of Materials & Metallurgy, Northeastern University, Shenyang 110819 (China); Lu, Shuaidan; Huang, Xiaoxiao; Li, Kuanhe; Tu, Ganfeng [School of Materials & Metallurgy, Northeastern University, Shenyang 110819 (China); Huang, Xiaowei [National Engineering Research Center for Rare Earth Materials, General Research Institute for Non-Ferrous Metals, and Grirem Advanced Materials Co., Ltd., Beijing 100088 (China); Huang, Shaodong [School of Materials & Metallurgy, Northeastern University, Shenyang 110819 (China); Inner Mongolia Baotou Steel Rare-earth (Group) Hi-tech. Co., Ltd. Inner Mongolia, Baotou 014030 (China)

    2016-07-20

    Highlights: • The surface tensions of typical RE fluoride melts were systematically studied. • The temperature and composition dependences of the surface tensions were discussed. • Surface tension factor of RE{sub 2}O{sub 3} was studied and the solubility was the key point. • Results of this study are novel and well supplement data base of RE fluoride melts. - Abstract: The surface tensions of REF{sub 3}-LiF (RE = La and Nd) molten salts (REF{sub 3} mol% = 20-40%) were measured using the slide method over the temperature range1223–1423 K which was specifically chosen for meeting the actual electrolysis temperature (about 1323 K). The temperature and composition dependences of the surface tensions were investigated. The results showed that the surface tension decreased linearly with the increasing of temperature and increased nonlinearly with the increasing mole fraction of REF{sub 3}. At 1323 K (near the practical electrolysis temperature), the surface tension of REF{sub 3}-LiF-RE{sub 2}O{sub 3} molten salts firstly increased with the increasing RE{sub 2}O{sub 3} and reached the maximum value near the solubility of RE{sub 2}O{sub 3} (2–3 g) in REF{sub 3}-LiF molten salts, and then decreased with the continuously adding RE{sub 2}O{sub 3}. The accurate knowledge of the surface tension factor of RE{sub 2}O{sub 3} can be useful for well understanding the solubilizing mechanisms of RE{sub 2}O{sub 3} in REF{sub 3}-LiF molten salts system. Results of this study well supplemented the experimental data of physiochemical property on surface tension of rare earth fluoride electrolytes.

  9. Alkaline and alkaline earth metal phosphate halides and phosphors

    Science.gov (United States)

    Lyons, Robert Joseph; Setlur, Anant Achyut; Cleaver, Robert John

    2012-11-13

    Compounds, phosphor materials and apparatus related to nacaphite family of materials are presented. Potassium and rubidium based nacaphite family compounds and phosphors designed by doping divalent rare earth elements in the sites of alkaline earth metals in the nacaphite material families are descried. An apparatus comprising the phosphors based on the nacaphite family materials are presented herein. The compounds presented is of formula A.sub.2B.sub.1-yR.sub.yPO.sub.4X where the elements A, B, R, X and suffix y are defined such that A is potassium, rubidium, or a combination of potassium and rubidium and B is calcium, strontium, barium, or a combination of any of calcium, strontium and barium. X is fluorine, chlorine, or a combination of fluorine and chlorine, R is europium, samarium, ytterbium, or a combination of any of europium, samarium, and ytterbium, and y ranges from 0 to about 0.1.

  10. Rare earth element and rare metal inventory of central Asia

    Science.gov (United States)

    Mihalasky, Mark J.; Tucker, Robert D.; Renaud, Karine; Verstraeten, Ingrid M.

    2018-03-06

    Rare earth elements (REE), with their unique physical and chemical properties, are an essential part of modern living. REE have enabled development and manufacture of high-performance materials, processes, and electronic technologies commonly used today in computing and communications, clean energy and transportation, medical treatment and health care, glass and ceramics, aerospace and defense, and metallurgy and chemical refining. Central Asia is an emerging REE and rare metals (RM) producing region. A newly compiled inventory of REE-RM-bearing mineral occurrences and delineation of areas-of-interest indicate this region may have considerable undiscovered resources.

  11. Electron-phonon coupling in the rare-earth metals

    DEFF Research Database (Denmark)

    Skriver, Hans Lomholt; Mertig, I.

    1990-01-01

    We have estimated the strength of the mass enhancement of the conduction electrons due to electron-phonon interaction in the rare metals Sc, Y, and La–Lu. The underlying self-consistent energy bands were obtained by means of the scalar relativistic linear-muffin-tin-orbital method, and the electron......-phonon parameters were calculated within the Gaspari-Gyorffy formulation. For the heavier rare earths Gd–Tm spin polarization was included both in the band-structure calculations and in the treatment of the electron-phonon coupling to take into account the spin splitting of the conduction electrons induced by the 4...

  12. The effects of soluble salts at the metal/paint interface: advances in knowledge

    OpenAIRE

    Fuente, Daniel de la; Chico, Belén; Morcillo, Manuel

    2006-01-01

    The presence of soluble salts (particularly sulphates and chlorides) at the metal/paint interface is known to have a detrimental effect on the integrity of most paint systems. Though this is a long-standing problem, it has recently come to receive greater attention from the protective coatings industry. International Standards Organization (ISO) has for some time been trying to develop a standard about guidance levels for water-soluble salt contamination before the application of paints and r...

  13. Ageing behaviour of unary hydroxides in trivalent metal salt ...

    Indian Academy of Sciences (India)

    LDH)-like phases on ageing in solutions of Al or Cr salts. This reaction is similar to acid leaching and proceeds by a dissolution–reprecipitation mechanism offering a simple method of LDH synthesis, with implications for the accepted theories of ...

  14. Ageing behaviour of unary hydroxides in trivalent metal salt solutions

    Indian Academy of Sciences (India)

    LDH)-like phases on ageing in solutions of Al or Cr salts. This reaction is similar to acid leaching and proceeds by a dissolution–reprecipitation mechanism offering a simple method of LDH synthesis, with implications for the accepted theories of ...

  15. Mineralogy and heavy metal content of secondary mineral salts: A ...

    African Journals Online (AJOL)

    tailings contain about 30 million tonnes of sulphur and 430 000 tonnes of uranium in the tailings storage facilities (Weiersbye and Witkowski., 2006). It is estimated that 25 million litres of contaminated water is discharged daily into surface water bodies and 100 tonnes of efflorescent salt is deposited into the surrounding ...

  16. Halophyte vegetation influences in salt marsh retention capacity for heavy metals

    Energy Technology Data Exchange (ETDEWEB)

    Reboreda, Rosa [Institute of Oceanography, Faculty of Sciences, University of Lisbon, Campo Grande, Rua Ernesto de Vasconcelos, 1749-016 Lisbon (Portugal); Cacador, Isabel [Institute of Oceanography, Faculty of Sciences, University of Lisbon, Campo Grande, Rua Ernesto de Vasconcelos, 1749-016 Lisbon (Portugal)]. E-mail: micacador@fc.ul.pt

    2007-03-15

    We analysed concentrations of Cu, Cd and Pb in above and belowground tissues of the halophyte species Halimione portulacoides and Spartina maritima, as well as in sediments and pore water between the roots in a Tagus estuary salt marsh (Portugal). From these results we calculated the pools of metals in the compartments mentioned above. Relative percentages of accumulation in each pool were also determined. Our aim was to determine how the type of vegetation in the salt marsh affects overall metal retention capacity of the system. It was concluded that areas colonised by H. portulacoides are potential sources of Cu, Cd and Pb to the marsh ecosystem, whereas areas colonised by S. maritima are more effective sinks at least for Cu and Cd. Consequently, S. maritima seems to contribute more effectively to the stabilisation of metals in salt marsh sediments, reducing their availability to the estuarine system. - The type of vegetal cover can affect the overall retention capacity of a salt marsh as well as the functioning of the salt marsh as a sink or source of metals to the estuarine system.

  17. The Effect of Salts in Promoting Specific and Competitive Interactions between Zinc Finger Proteins and Metals

    Science.gov (United States)

    Li, Gongyu; Yuan, Siming; Zheng, Shihui; Chen, Yuting; Zheng, Zhen; Liu, Yangzhong; Huang, Guangming

    2017-12-01

    Specific protein-metal interactions (PMIs) fulfill essential functions in cells and organic bodies, and activation of these functions in vivo are mostly modulated by the complex environmental factors, including pH value, small biomolecules, and salts. Specifically, the role of salts in promoting specific PMIs and their competition among various metals has remained untapped mainly due to the difficulty to distinguish nonspecific PMIs from specific PMIs by classic spectroscopic techniques. Herein, we report Hofmeister salts differentially promote the specific PMIs by combining nanoelectrospray ionization mass spectrometry and spectroscopic techniques (fluorescence measurement and circular dichroism). Furthermore, to explore the influence of salts in competitive binding between metalloproteins and various metals, we designed a series of competitive experiments and applied to a well-defined model system, the competitive binding of zinc (II) and arsenic (III) to holo-promyelocytic leukemia protein (PML). These experiments not only provided new insights at the molecular scale as complementary to previous NMR and spectroscopic results, but also deduced the relative binding ability between zinc finger proteins and metals at the molecular scale, which avoids the mass spectrometric titration-based determination of binding constants that is frequently affected and often degraded by variable solution conditions including salt contents. [Figure not available: see fulltext.

  18. Participation of Taxifolin in the Protection of Soya Seeds from the Effects of Heavy Metal Salts

    Directory of Open Access Journals (Sweden)

    V.A. Kuznetsova

    2015-06-01

    Full Text Available A correlation was revealed between the specific activity of peroxidases and their multiple forms during the germination of soya seeds (Glycine max (L. Merrill in the presence of heavy metal salts. It was shown that lead and cadmium sulfates cause emergence of new forms of the enzyme with high electrophoretic mobility, which indicates that the identified enzyme forms are involved in the molecular mechanism of adaptation to oxidative stress. Addition of taxifolin (dihydroquercetin, a bioflavonoid antioxidant, to the salts of heavy metals caused decrease in the specific activity of peroxidases and favored emergence of new forms of the enzyme, which were absent in the control samples.

  19. Transgenerational Adaptation to Heavy Metal Salts in Arabidopsis

    OpenAIRE

    Rahavi, Mohammad Reza; Migicovsky, Zoë; Titov, Viktor; Kovalchuk, Igor

    2011-01-01

    Exposure to abiotic and biotic stress results in changes in plant physiology and triggers genomic instability. Recent reports suggest that the progeny of stressed plants also exhibit changes in genome stability, stress tolerance, and methylation. Here we analyzed whether exposure to Ni2+, Cd2+, and Cu2+ salts leads to transgenerational changes in homologous recombination frequency and stress tolerance. We found that the immediate progeny of stressed plants exhibited an increased rate of recom...

  20. Ageing behaviour of unary hydroxides in trivalent metal salt solutions

    Indian Academy of Sciences (India)

    Unknown

    Figure 2. Powder X-ray diffractogram of CuO (a) compared with those of CuO aged in aluminium nitrate for 2 days (b) and 4 days (c). Feature marked by asterisk is due to impurities. Table 2. Powder X-ray diffraction data of layered double hydroxides obtained by the ageing of unary hydroxides in Al (or Cr) salt solutions. d/Å.

  1. Rare earth metal boron carbide MBC compounds containing monodimensional branched zigzag chains of non-metal atoms: Theoretical aspects

    International Nuclear Information System (INIS)

    Wiitkar, F.; Kahlal, S.; Halet, J.F.; Saillard, J.Y.

    1995-01-01

    The authors apply extended Hueckel calculations to solving the electronic structure of rare earth metal boron carbides. These compounds contain boron-carbon zigzag chains the structure of which is dictated by the ionic nature of the interaction between the chains and the rare earth metal. The authors report a relationship between formal charge of the BC units and structural orientation of the chains

  2. FUSED SALT METHOD FOR COATING URANIUM WITH A METAL

    Science.gov (United States)

    Eubank, L.D.

    1959-02-01

    A method is presented for coating uranium with a less active metal such as Cr, Ni, or Cu comprising immersing the U in a substantially anhydrous molten solution of a halide of these less active metals in a ternary chloride composition which consists of selected percentages of KCl, NaCl and another chloride such as LiCl or CaCl/sub 2/.

  3. Alkali metal bismuth(III) chloride double salts

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, Andrew W. [Department of Chemistry, College of William and Mary, Williamsburg, VA 23187 (United States); Nicholas, Aaron; Ahern, John C. [Department of Chemistry, University of Maine, Orono, ME 04469 (United States); Chan, Benny [Department of Chemistry, College of New Jersey, Ewing, NJ 08628-0718 (United States); Patterson, Howard H. [Department of Chemistry, University of Maine, Orono, ME 04469 (United States); Pike, Robert D., E-mail: rdpike@wm.edu [Department of Chemistry, College of William and Mary, Williamsburg, VA 23187 (United States)

    2016-06-15

    Evaporative co-crystallization of MCl (M = Na, K, Rb, Cs) with BiOCl in aqueous HCl produces double salts: M{sub x}Bi{sub y}Cl{sub (x+3y)}·zH{sub 2}O. The sodium salt, Na{sub 2}BiCl{sub 5}·5H{sub 2}O (monoclinic P2{sub 1}/c, a = 8.6983(7) Å, b = 21.7779(17) Å, c = 7.1831(6) Å, β = 103.0540(10)°, V = 1325.54(19) Å{sup 3}, Z = 4) is composed of zigzag chains of μ{sub 2}-Cl-cis-linked (BiCl{sub 5}){sub n}{sup 2n–} chains. Edge-sharing chains of NaCl{sub n}(OH{sub 2}){sub 6−n} octahedra (n = 0, 2, 3) are linked through μ{sub 3}-Cl to Bi. The potassium salt, K{sub 7}Bi{sub 3}Cl{sub 16} (trigonal R−3c, a = 12.7053(9) Å, b = 12.7053(9) Å, c = 99.794(7) Å, V = 13,951(2) Å{sup 3}, Z = 18) contains (Bi{sub 2}Cl{sub 10}){sup 4–} edge-sharing dimers of octahedra and simple (BiCl{sub 6}){sup 3–} octahedra. The K{sup +} ions are 5- to 8-coordinate and the chlorides are 3-, 4-, or 5-coordinate. The rubidium salt, Rb{sub 3}BiCl{sub 6}·0.5H{sub 2}O (orthorhombic Pnma, a = 12.6778(10) Å, b = 25.326(2) Å, c = 8.1498(7) Å, V = 2616.8(4) Å{sup 3}, Z = 8) contains (BiCl{sub 6}){sup 3–} octahedra. The Rb{sup +} ions are 6-, 8-, and 9-coordinate, and the chlorides are 4- or 5-coordinate. Two cesium salts were formed: Cs{sub 3}BiCl{sub 6} (orthorhombic Pbcm, a = 8.2463(9) Å, b = 12.9980(15) Å, c = 26.481(3) Å, V = 2838.4(6) Å{sup 3}, Z = 8) being comprised of (BiCl{sub 6}){sup 3–} octahedra, 8-coordinate Cs{sup +}, and 3-, 4-, and 5-coordinate Cl{sup −}. In Cs{sub 3}Bi{sub 2}Cl{sub 9} (orthorhombic Pnma, a = 18.4615(15) Å, b = 7.5752(6) Å, c = 13.0807(11) Å, V = 1818.87(11) Å{sup 3}, Z = 4) Bi octahedra are linked by μ{sub 2}-bridged Cl into edge-sharing Bi{sub 4} squares which form zigzag (Bi{sub 2}Cl{sub 9}){sub n}{sup 3n–} ladders. The 12-coordinate Cs{sup +} ions bridge the ladders, and the Cl{sup −} ions are 5- and 6-coordinate. Four of the double salts are weakly photoluminescent at 78 K, each showing a series of three excitation peaks

  4. Notable effects of metal salts on UV-vis absorption spectra of α-, β-, γ-, and δ-tocopheroxyl radicals in acetonitrile solution. The complex formation between tocopheroxyls and metal cations.

    Science.gov (United States)

    Mukai, Kazuo; Kohno, Yutaro; Ouchi, Aya; Nagaoka, Shin-ichi

    2012-08-02

    The measurements of the UV-vis absorption spectra of α-, β-, γ-, and δ-tocopheroxyl (α-, β-, γ-, and δ-Toc(•)) radicals were performed by reacting aroxyl (ArO(•)) radical with α-, β-, γ-, and δ-tocopherol (α-, β-, γ-, and δ-TocH), respectively, in acetonitrile solution including three kinds of alkali and alkaline earth metal salts (LiClO(4), NaClO(4), and Mg(ClO(4))(2)) (MX or MX(2)), using stopped-flow spectrophotometry. The maximum wavelengths (λ(max)) of the absorption spectra of the α-, β-, γ-, and δ-Toc(•) located at 425-428 nm without metal salts increased with increasing concentrations of metal salts (0-0.500 M) in acetonitrile and approached some constant values, suggesting (Toc(•)···M(+) (or M(2+))) complex formations. Similarly, the values of the apparent molar extinction coefficient (ε(max)) increased drastically with increasing concentrations of metal salts in acetonitrile and approached some constant values. The result suggests that the formations of Toc(•) dimers were suppressed by the metal ion complex formations of Toc(•) radicals. The stability constants (K) were determined for Li(+), Na(+), and Mg(2+) complexes of α-, β-, γ-, and δ-Toc(•). The K values increased in the order of NaClO(4) metal salt. The alkali and alkaline earth metal salts having a smaller ionic radius of the cation and a larger charge of the cation gave a larger shift of the λ(max) value, a larger ε(max) value, and a larger K value. The result of the DFT molecular orbital calculations indicated that the α-, β-, γ-, and δ-Toc(•) radicals were stabilized by the (1:1) complex formation with metal cations (Li(+), Na(+), and Mg(2+)). Stabilization energy (E(S)) due to the complex formation increased in the order of Na(+) complexes, being independent of the kinds of Toc(•) radicals. The calculated result also indicated that the metal cations coordinate to the O atom at the sixth position of α-, β-, γ-, and δ-Toc(•) radicals.

  5. On salting in effect of the second group metal rhodanides on aqueous-amine solutions

    International Nuclear Information System (INIS)

    Krupatkin, I.L.; Ostrovskaya, E.M.; Vorob'eva, L.D.; Kamyshnikova, G.V.

    1978-01-01

    The ''salting in'' effect of rhodanides of Group 2 metals (magnesium, calcium, strontium, barium) on aqueous-amine solutions (water-aniline, and water-o-toluidine systems) is studied. The solubility in these systems has been determined by the isothermal method at 25 deg C. Compositions of the co-existing liquid phases have been determined by refractometry. The phase diagrams of water-aniline-rhodanide of magnesium, calcium and strontium systems have the same qualitative view. These rhodanides ''salt in'' the water-aniline system so strongly that the systems are completely homogenized. According to the decreasing homogenization effect on the water-aniline and water-o-toluidine systems the salts may be arranged into the following series Mg(NCS) 2 >Ca(NCS) 2 >Sr(NCS) 2 >Ba(NCS) 2 . The ''salting in'. effect is weaker in the water-o-toluidine system rather than in the water-aniline one

  6. Oxygen production by molten alkali metal salts using multiple absorption-desorption cycles

    Science.gov (United States)

    Cassano, A.A.

    1985-07-02

    A continuous chemical air separation is performed wherein oxygen is recovered with a molten alkali metal salt oxygen acceptor in a series of absorption zones which are connected to a plurality of desorption zones operated in separate parallel cycles with the absorption zones. A greater recovery of high pressure oxygen is achieved at reduced power requirements and capital costs. 3 figs.

  7. Stabilization of polyamides IV. Thermooxidation of hexano-6-lactam in the presence of alkali metal salts

    Czech Academy of Sciences Publication Activity Database

    Lánská, Božena; Matisová-Rychlá, L.; Rychlý, J.

    2005-01-01

    Roč. 87, č. 2 (2005), s. 361-373 ISSN 0141-3910 R&D Projects: GA AV ČR(CZ) KSK4050111 Institutional research plan: CEZ:AV0Z40500505 Keywords : oxidation of N-alkylamides * alkali metal salts * chemiluminescence of reactions Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.749, year: 2005

  8. Ba/Cd/Zn metal salts carboxylate and dibasic lead stearate

    African Journals Online (AJOL)

    Revue Synthèse N° 20, Juin 2009. S.F. Chabira et M. Sebaa. 94. Effect of thermal stabilizers. (Ba/Cd/Zn metal salts carboxylate and dibasic lead stearate) on the kinetic of carbonyls formation of PVC films. Salem Fouad Chabira et Mohamed Sebaa. Department of Mechanics, Laghouat University,. BP 37 G, Laghouat 03000, ...

  9. Oxygen production by molten alkali metal salts using multiple absorption-desorption cycles

    Science.gov (United States)

    Cassano, Anthony A.

    1985-01-01

    A continuous chemical air separation is performed wherein oxygen is recovered with a molten alkali metal salt oxygen acceptor in a series of absorption zones which are connected to a plurality of desorption zones operated in separate parallel cycles with the absorption zones. A greater recovery of high pressure oxygen is achieved at reduced power requirements and capital costs.

  10. In vitro Effects of Three Metallic Salts and Carbon Black (Soot) on ...

    African Journals Online (AJOL)

    The antifungal effects of zinc chloride (Zn Cl2) calcium chloride (CaCl2), magnesium chloride (MgCl2) as well as soot collected from a local kitchen were tested on five isolated species of the dermatophytes from cases of human dermatophytoses. Of these three metallic salts, ZnCl2 showed the highest inhibitory effect on the ...

  11. Eliminating inhibition of enzymatic hydrolysis by lignosulfonate in unwashed sulfite-pretreated aspen using metal salts

    Science.gov (United States)

    Hao Liu; Junyong Zhu

    2010-01-01

    This study demonstrated the efficiency of Ca(II) and Mg(II) in removing inhibition of enzymatic hydrolysis by lignosulfonate through non-productive adsorption of enzymes. Adding 1 mmol/g cellulose of either metal salt restores approximately 65% of the activity lost when a pure cellulose/cellulase solution is spiked with lignosulfonate. Addition of either Ca(II) or Mg(...

  12. Assessment of a 42 metal salts chemical library in mouse embryonic stem cells

    Science.gov (United States)

    The developmental effects of xenobiotics on differentiation can be profiled using mouse embryonic stem cells (mESCs). The adherent cell differentiation and cytotoxicity (ACDC) technique was used to evaluate a library of 42 metal and metaloid salts. Jl mESCs were allowed to prolif...

  13. Effects of Cations on Corrosion of Inconel 625 in Molten Chloride Salts

    Science.gov (United States)

    Zhu, Ming; Ma, Hongfang; Wang, Mingjing; Wang, Zhihua; Sharif, Adel

    2016-04-01

    Hot corrosion of Inconel 625 in sodium chloride, potassium chloride, magnesium chloride, calcium chloride and their mixtures with different compositions is conducted at 900°C to investigate the effects of cations in chloride salts on corrosion behavior of the alloy. XRD, SEM/EDS were used to analyze the compositions, phases, and morphologies of the corrosion products. The results showed that Inconel 625 suffers more severe corrosion in alkaline earth metal chloride molten salts than alkaline metal chloride molten salts. For corrosion in mixture salts, the corrosion rate increased with increasing alkaline earth metal chloride salt content in the mixture. Cations in the chloride molten salts mainly affect the thermal and chemical properties of the salts such as vapor pressure and hydroscopicities, which can affect the basicity of the molten salt. Corrosion of Inconel 625 in alkaline earth metal chloride salts is accelerated with increasing basicity.

  14. Mineralogy and heavy metal content of secondary mineral salts: A ...

    African Journals Online (AJOL)

    Secondary minerals associated with acid mine drainage play an important role in metal cycling and may pose a geochemical hazard. The occurrence of secondary minerals indicates prevailing and past geochemical conditions. Detecting and characterising secondary minerals is necessary to the planning of remediation ...

  15. Obtainment of lithium metal by electrolysis of molten salts

    International Nuclear Information System (INIS)

    Silva Costa, M.A.Z. da.

    1988-04-01

    The obtainment metallic lithium through KCL + LiCl, using a stainless steel cathode and a graphite anode is studied. The applications of lithium on nuclear energy, aerospatial program, metalurgy and as refining and degassing agent are also presented. The purification of lithium is still mentioned. (C.G.C.) [pt

  16. The magnetoresistivity of some rare-earth metals

    International Nuclear Information System (INIS)

    Webber, G.D.

    1978-10-01

    The thesis describes measurements of the low temperature transverse magnetoresistivities of single crystals of rare-earth metals in magnetic fields up to 8 Tesla. A general introduction to the rare-earths, their magnetic properties and a review of the basic theory and mechanism of magnetoresistivity is given. Details of the crystal structure, growth of single crystals and sample mounting method follow. The experimental equipment and measuring techniques are then described. The low temperature transverse magnetoresistivity of polycrystalline lanthanum and single crystal praseodymium for the temperature range 4.2 - 30K is measured. The separation of the spin-disorder and Fermi-surface orbital effect contributions are described and the theoretical and experimental spin-disorder values compared. Magnetoresistivity measurements for neodymium single crystals (4.2 - 30K) are compared with the magnetic properties determined from neutron diffraction studies. Results for gadolinium single crystals (4.2 - 200K) are compared for two different impurity levels and with previous work. (UK)

  17. Interactions between salt marsh plants and Cu nanoparticles - Effects on metal uptake and phytoremediation processes.

    Science.gov (United States)

    Andreotti, Federico; Mucha, Ana Paula; Caetano, Cátia; Rodrigues, Paula; Rocha Gomes, Carlos; Almeida, C Marisa R

    2015-10-01

    The increased use of metallic nanoparticles (NPs) raises the probability of finding NPs in the environment. A lot of information exists already regarding interactions between plants and metals, but information regarding interactions between metallic NPs and plants, including salt marsh plants, is still lacking. This work aimed to study interactions between CuO NPs and the salt marsh plants Halimione portulacoides and Phragmites australis. In addition, the potential of these plants for phytoremediation of Cu NPs was evaluated. Plants were exposed for 8 days to sediment elutriate solution doped either with CuO or with ionic Cu. Afterwards, total metal concentrations were determined in plant tissues. Both plants accumulated Cu in their roots, but this accumulation was 4 to 10 times lower when the metal was added in NP form. For P. australis, metal translocation occurred when the metal was added either in ionic or in NP form, but for H. portulacoides no metal translocation was observed when NPs were added to the medium. Therefore, interactions between plants and NPs differ with the plant species. These facts should be taken in consideration when applying these plants for phytoremediation of contaminated sediments in estuaries, as the environmental management of these very important ecological areas can be affected. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Evaluation of complexing agents and column temperature in ion chromatographic separation of alkali metals, alkaline earth metals and transition metals ion

    International Nuclear Information System (INIS)

    Kelkar, Anoop; Pandey, Ashish; Name, Anil B.; Das, D.K.; Behere, P.G.; Mohd Afzal

    2015-01-01

    The aim of ion chromatography method development is the resolution of all metal ions of interests. Resolution can be improved by changing the selectivity. Selectivity in chromatography can be altered by changes in mobile phase (eg eluent type, eluent strength) or through changes in stationary phase. Temperature has been used in altering the selectivity of particularly in reversed phase liquid chromatography and ion exchange chromatography. Present paper describe the retention behaviour of alkali metals, alkaline earth metals and transition metal ions on a silica based carboxylate function group containing analyte column. Alkali metals, alkaline earth metals and transition metal ions were detected by ion conductivity and UV-VIS detectors respectively

  19. Electromigration in molten salts and application to isotopic separation of alkaline and alkaline-earth elements

    International Nuclear Information System (INIS)

    Menes, F.

    1969-01-01

    The separation of the isotopes of the alkaline-earth elements has been studied using counter-current electromigration in molten bromides. The conditions under which the cathode operates as a bromine electrode for the highest possible currents have been examined. For the separation of calcium, it has been necessary to use a stable CaBr 2 - (CaBr 2 + KBr) 'chain'. In the case of barium and strontium, it was possible to employ the pure bromides. Enrichment factors of the order of 10 for 48 Ca and of the order of 1.5 for the rare isotopes of barium and strontium have been obtained. In the case of magnesium the method is slightly more difficult to apply because of material loss due to the relatively high vapour pressure of the salt requiring the use of electrolyte chains, MgBr 2 - CeBr 3 . A study has been made that has led to a larger-scale application of the method. These are essentially the inhibition of reversible operation of the cathode by traces of water, limiting the intensity which can be tolerated; evacuation of the heat produced by the Joule effect, in the absence of which the separation efficiency is reduced by thermal gradients; corrosion of the materials by molten salts at high temperature. Several cells capable of treating a few kilograms of substance have been put into operation; none of these has lasted long enough to produce a satisfactory enrichment. The method is thus limited actually to yields of the order of a few grams. (author) [fr

  20. Commonly used metal and crystalline salts in South African traditional medicine.

    Science.gov (United States)

    Street, R A; Cele, M P

    2013-06-21

    Traditional medicines in the form of plants, animals and/or minerals are used by millions of South Africans. There is currently no data regarding the commonly used mineral elements thus the potential benefits or hazards of such products remain unclear. Metal and crystalline salts were purchased from a rural market (Nongoma, Zululand, South Africa). Information regarding the colloquial name, price and weight was recorded. Energy dispersive X-ray spectroscopy (EDX) was used to quantatively determine the unknown salts. Six widely available salts were analyzed. Ndonya, as it is colloquially known, refers to two products which look identical to the untrained eye-one is dyed table salt and the other is hexavalent chromium. A further product used medicinally, although not widely available, was identified as iron chromite ore. The array of substances documented, ranging from benign to carcinogenic, stresses the importance of documenting components used in traditional medicine and confirms the necessity to regulate South Africa traditional medicine. Healthcare workers should be aware of the complexities of using such metal salt. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  1. The influence of temperature and salt on metal and sediment removal in stormwater biofilters.

    Science.gov (United States)

    Søberg, Laila C; Viklander, Maria; Blecken, Godecke-Tobias

    2014-01-01

    Stormwater biofilters are used to treat stormwater runoff. In countries with cold winter climates, biofilters are subject to low temperatures which, in some cases, are combined with potentially high salt concentrations from road de-icing, potentially affecting the biofilter's performance. Since stormwater biofilters have been developed without consideration of their critical winter use, a laboratory study was carried out to evaluate the performance of stormwater biofilters subjected to low and high temperatures, with and without salt. Both factors and their interaction had a significant effect on outflow concentrations and removal percentages. Salt had a negative impact on outflow concentrations, causing lower removal percentages for (especially dissolved) metals, this impact being most pronounced for Cu and Pb. The unrealistic combination of salt with high temperature seemed to further amplify the negative impacts of salt despite the fact that temperature alone did not cause significant differences in outflow concentrations and removal percentages. Still, biofilters showed the ability to treat stormwater efficiently under the simulated winter conditions; outflow concentrations for total metals as a minimum met the class 4 threshold value defined in the Swedish freshwater quality guidelines, while inflow concentrations clearly exceeded the threshold value for class 5. The relatively coarse filter material (which is recommended to facilitate infiltration during winter) did not seem to exacerbate biofilter performance.

  2. Effect of metal salts on antibacterial activity of zingiber officinale roscoe extract

    International Nuclear Information System (INIS)

    Sohail, T.; Yaqeen, Z.; Imran, H.; Rehman, Z.; Fatima, N.

    2013-01-01

    The antibacterial activity of ethanol extract of Zingiber Officinale Roscoe (ginger) and its combination with different salts like CuSO/sub 4/, ZnSO/sub 4/ and MnCl/sub 2/ was investigated. Both Gram positive and Gram negative bacteria were tested by agar diffusion method. The results showed that ethanol extract of Zingiber Officinale gave the maximum zone of inhibition at 50 mg/ml concentrations against Escherichia coli among Gram negative bacteria and against Staphylococcus aureus in Gram positive bacteria. However antibacterial activity of the ginger and metal salts combination was greater than activity of ethanol extract. These investigations indicate that though ethanol extract has antibacterial activity against Gram positive and Gram negative bacteria, ginger and metal salts complex has more inhibitory effect on microorganisms. Antibacterial activity was also compared with standard drug ampicillin. The minimum inhibitory concentration (MIC) of ginger extract and metal salts complexes against all test organisms ranged from 0.3125 to 2.5 mg/ml. (author)

  3. Spatial and seasonal variation in heavy metals in interstitial water of salt marsh soils

    Energy Technology Data Exchange (ETDEWEB)

    Otero, X.L.; Macias, Felipe

    2002-12-01

    Soil colonization by plants affected spatial and seasonal variation in heavy metals. - The composition of interstitial water collected from a salt marsh in NW Spain showed clear seasonal and spatial variations associated with redox cycles of Fe and S. In the summer, salinity increased in all soils as a consequence of the increase in evapotranspiration. The pH and concentrations of heavy metals also differed with season, but not all environments showed the same variations. Soils not colonized by plants had the highest pH and lowest heavy metal concentrations in the summer. These results support the idea that higher temperatures lead to an increase in the activity of sulfate-reducing bacteria, which in turn leads to an increase in alkalinity and concentration of sulfides in the water. Trace metals tend to precipitate with sulfides under these conditions and are removed from the interstitial water. In contrast, in the soils colonized by Spartina maritima, the oxidation of metal sulfides during the summer led to a decrease in pH and an increase in the metal concentrations in the interstitial water. The results obtained concur with those found for seasonal variations in metal sulfides in soils from the same salt marsh.

  4. Synthesis of borohydrides of rare earth metals by mechanic-chemical methods

    International Nuclear Information System (INIS)

    Gafurov, B.A.; Nasrulloeva, D.Kh.; Khakyorov, I.Z.; Saidov, V.Ya.

    2010-01-01

    Present article is devoted to synthesis of borohydrides of rare earth metals by mechanic-chemical methods. The borohydrides of rare earth metals were obtained by means of mechanic-chemical methods. Physicochemical properties of obtained lanthanoid borohydrides were studied by means of X-ray phase analysis.

  5. Production by metallothermics of pure alloys of rare earths and transition metals

    International Nuclear Information System (INIS)

    Jourdan, A.

    1988-01-01

    Industrial process of production of high purity master alloys ingots by the thermite process from a rare earth compound which is reduced by a reducing agent like alkaline or alkaline earth metals. The process is characterized by introduction of the transition metal into the initial reaction mixture, at least in part, as a compound than can be reduced by the reducing agent [fr

  6. Synthesis, structure and reactivity of rare-earth metal complexes containing anionic phosphorus ligands.

    Science.gov (United States)

    Li, Tianshu; Kaercher, Sabrina; Roesky, Peter W

    2014-01-07

    A comprehensive review of structurally characterized rare-earth metal complexes containing anionic phosphorus ligands is presented. Since rare-earth elements form hard ions and phosphorus is considered as a soft ligand, the rare-earth metal phosphorus coordination is regarded as a less favorite combination. Three classes of phosphorus ligands, (1) the monoanionic organophosphide ligands (PR2(-)) bearing one negative charge on the phosphorus atom; (2) the dianionic phosphinidene (PR(2-)) and P(3-) ligands; and (3) the pure inorganic polyphosphide ligands (Pn(x-)), are included here. Particular attention has been paid to the synthesis, structure, and reactivity of the rare-earth metal phosphides.

  7. Release characteristics of alkali and alkaline earth metallic species during biomass pyrolysis and steam gasification process.

    Science.gov (United States)

    Long, Jiang; Song, Hu; Jun, Xiang; Sheng, Su; Lun-Shi, Sun; Kai, Xu; Yao, Yao

    2012-07-01

    Investigating the release characteristics of alkali and alkaline earth metallic species (AAEMs) is of potential interest because of AAEM's possible useful service as catalysts in biomass thermal conversion. In this study, three kinds of typical Chinese biomass were selected to pyrolyse and their chars were subsequently steam gasified in a designed quartz fixed-bed reactor to investigate the release characteristics of alkali and alkaline earth metallic species (AAEMs). The results indicate that 53-76% of alkali metal and 27-40% of alkaline earth metal release in pyrolysis process, as well as 12-34% of alkali metal and 12-16% of alkaline earth metal evaporate in char gasification process, and temperature is not the only factor to impact AAEMs emission. The releasing characteristics of AAEMs during pyrolysis and char gasification process of three kinds of biomass were discussed in this paper. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Rare-earth metal prices in the USA ca. 1960 to 1994

    Science.gov (United States)

    Hedrick, James B.

    1997-01-01

    Rare-earth metal prices were compiled from the late 1950s and early 1960s through 1994. Although commercial demand for rare-earth metals began in 1908, as the alloy mischmetal, commercial quantities of a wide range of individual rare-earth metals were not available until the late 1950s. The discovery of a large, high-grade rare-earth deposit at Mountain Pass. CA, USA, in 1949, was significant because it led to the production of commercial quantities or rare-earth elements that reduced prices and encouraged wider application of the materials. The availability of ore from Mountain Pass, and other large rare-earth deposits, especially those in Australia and China, has provided the world with abundant resources for rare-earth metal production. This availability, coupled with improved technology from Government and private-sector metallurgical research, has resulted in substantial decreases in rare-earth metal prices since the late 1950s and early 1960s. Price series for the individual rare-earth metals (except promethium) are quoted on a kilogram basis from the late 1950s and early 1960s through 1994. Prices are given in US dollars on an actual and constant dollar basis. Industrial and economic factors affecting prices during this time period are examined.

  9. Accumulation and biological cycling of heavy metal in four salt marsh species, from Tagus estuary (Portugal)

    Energy Technology Data Exchange (ETDEWEB)

    Duarte, B., E-mail: baduarte@fc.ul.p [Centro de Oceanografia, Instituto de Oceanografia, Campo Grande, 1749-1016 Lisboa (Portugal); Caetano, M. [INRB/IPIMAR - Instituto Nacional de Recursos Biologicos, Av. Brasilia, 1449-006 Lisboa (Portugal); Almeida, P.R. [Centro de Oceanografia, Instituto de Oceanografia, Campo Grande, 1749-1016 Lisboa (Portugal); Departamento de Biologia, Universidade de Evora, Largo dos Colegiais 2, 7004-516 Evora (Portugal); Vale, C. [INRB/IPIMAR - Instituto Nacional de Recursos Biologicos, Av. Brasilia, 1449-006 Lisboa (Portugal); Cacador, I. [Centro de Oceanografia, Instituto de Oceanografia, Campo Grande, 1749-1016 Lisboa (Portugal)

    2010-05-15

    Pools of Zn, Cu, Cd and Co in leaf, stem and root tissues of Sarcocornia fruticosa, Sarcocornia perennis, Halimione portulacoides and Spartina maritima were analyzed on a bimonthly basis, in a Tagus estuary salt marsh. All the major concentrations were found in the root tissues, being the concentrations in the aboveground organs neglectable for sediment budget proposes, as seen by the low root-aboveground translocation. Metal annual accumulation, root turnovers and cycling coefficients were also assessed. S. maritima showed the higher root turnovers and cycling coefficients for most of the analyzed metals, making this a phytostabilizer specie. By contrast the low root turnover, cycling coefficient and low root necromass generation makes S. perennis the most suitable specie for phytoremediation processes. Although the high amounts of metal return to the sediments, due to root senescence, salt marshes can still be considered sinks of heavy metals, cycling heavy metals mostly between sediment and root. - The efficiency of the phytoremediative processes and metal budgets are greatly influenced by the turnover periods and necromass generation.

  10. Biophysical and biochemical markers of metal/metalloid-impacts in salt marsh halophytes and their implications

    Directory of Open Access Journals (Sweden)

    Naser A. Anjum

    2016-04-01

    Full Text Available As a major sink, estuarine/salt marsh ecosystem can receive discharges laden with myriads of contaminants including metals/metalloids from man-made activities. Two among the major consequences of metal/metalloid-exposure in estuarine/salt marsh ecosystem flora such as halophytic plants are: (a the excessive accumulation of light energy that in turn leads to severe impairments in the photosystem II (PS II, and (b metal/metalloids-accrued elevation in reactive oxygen species (ROS in cells that causes imbalance in cellular redox homeostasis. On one hand, plants adopt several strategies to dissipate excessive energy hence eventually to avoid damage in the PS II and maintain optimum photosynthesis. On the other hand, components of cellular redox system quickly respond to metal/metalloid exposure, where plants try to maintain a fine-tuning therein and tightly control the level of ROS and its potential consequences. Based on recent reports this paper: (a overviews in separate sections major insights into and the significance of major biophysical and biochemical markers in metal/metalloid-exposed halophytes; and (b concludes the paper and highlights major points so far unexplored in the current context. Discussion reflects the need of integrating studies on major biophysical and biochemical markers in order finally to unveil tolerance/resistance mechanisms in halophytes under metal/metalloid exposed conditions.

  11. Molten salt extraction process for the recovery of valued transition metals from land-based and deep-sea minerals

    Science.gov (United States)

    Maroni, Victor A.; von Winbush, Samuel

    1988-01-01

    A process for extracting transition metals and particularly cobalt and manganese together with iron, copper and nickel from low grade ores (including ocean-floor nodules) by converting the metal oxides or other compositions to chlorides in a molten salt, and subsequently using a combination of selective distillation at temperatures below about 500.degree. C., electrolysis at a voltage not more negative than about -1.5 volt versus Ag/AgCl, and precipitation to separate the desired manganese and cobalt salts from other metals and provide cobalt and manganese in metallic forms or compositions from which these metals may be more easily recovered.

  12. Determination of uranium and rare-earth metals separation coefficients in LiCl-KCl melt by electrochemical transient techniques

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, S.A. [Institute of Chemistry, Kola Science Centre, RAS, 184200 Apatity, Murmansk Region (Russian Federation)]. E-mail: kuznet@chemy.kolasc.net.ru; Hayashi, H. [Japan Atomic Energy Research Institute, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Minato, K. [Japan Atomic Energy Research Institute, Tokai-mura, Naka-gun, Ibaraki-ken 319-1195 (Japan); Gaune-Escard, M. [Ecole Polytechnique, IUSTI-CNRS UMR 6595, Technopole de Chateau Gombert, F-13453 Marseille cedex 13 (France)

    2005-09-01

    The main step in the pyrometallurgical process of spent nuclear fuel recycling is a molten salt electrorefining. The knowledge of separation coefficients of actinides (U, Np, Pu and Am) and rare-earth metals (Y, La, Ce, Nd and Gd) is very important for this step. Usually the separation coefficients are evaluated from the formal standard potentials of metals in melts containing their own ions, values obtained by potentiometric method. Electrochemical experiments were carried out at 723-823 K in order to estimate separation coefficients in LiCl-KCl eutectic melt containing uranium and lanthanum trichlorides. It was shown that for the calculation of uranium and lanthanum separation coefficients it is necessary to determine the voltammetric peak potentials of U(III) and La(III), their concentration in the melt and the kinetic parameters relating to U(III) discharge such as transfer and diffusion coefficients, and standard rate constants of charge transfer.

  13. Determination of uranium and rare-earth metals separation coefficients in LiCl KCl melt by electrochemical transient techniques

    Science.gov (United States)

    Kuznetsov, S. A.; Hayashi, H.; Minato, K.; Gaune-Escard, M.

    2005-09-01

    The main step in the pyrometallurgical process of spent nuclear fuel recycling is a molten salt electrorefining. The knowledge of separation coefficients of actinides (U, Np, Pu and Am) and rare-earth metals (Y, La, Ce, Nd and Gd) is very important for this step. Usually the separation coefficients are evaluated from the formal standard potentials of metals in melts containing their own ions, values obtained by potentiometric method. Electrochemical experiments were carried out at 723-823 K in order to estimate separation coefficients in LiCl-KCl eutectic melt containing uranium and lanthanum trichlorides. It was shown that for the calculation of uranium and lanthanum separation coefficients it is necessary to determine the voltammetric peak potentials of U(III) and La(III), their concentration in the melt and the kinetic parameters relating to U(III) discharge such as transfer and diffusion coefficients, and standard rate constants of charge transfer.

  14. Antimicrobial activities of pomegranate rind extracts: enhancement by addition of metal salts and vitamin C

    Directory of Open Access Journals (Sweden)

    Kelly Alison F

    2008-12-01

    Full Text Available Abstract Background Punica granatum L. or pomegranates, have been reported to have antimicrobial activity against a range of Gram positive and negative bacteria. Pomegranate formulations containing ferrous salts have enhanced although short-term, antibacteriophage activities which are rapidly diminished owing to instability of the ferrous combination. The aim of this study was to determine the antimicrobial activities of combinations of pomegranate rind extracts (PRE with a range of metals salts with the added stabiliser vitamin C. Methods PRE solutions, prepared by blending rind sections with distilled water prior to sterilisation by autoclaving or filtration, were screened with a disc diffusion assay using penicillin G as a control. Suspension assays were used to determine the antimicrobial activities of PRE alone and in combination with salts of the following metals; Fe (II, Cu (II, Mn (II or Zn (II, and vitamin C, against a panel of microbes following exposure for 30 mins. The test organisms included Staphylococcus aureus, Bacillus subtilis, Escherichia coli, Pseudomonas aeruginosa and Proteus mirabilis. Results The screening assay demonstrated that PRE exhibited activity against the Gram positive organisms at 24 h with no observable effect on any of the Gram negative bacteria. However, after 12 h, zones of inhibition were only observed for Ps. aeruginosa. In contrast, using the suspension assay, addition of Cu (II salts to PRE solutions extended the activities resulting in no detectable growth being observed for the PRE/Cu (II combination against E. coli, Ps. aeruginosa and P. mirabilis. Minimal antimicrobial activity was observed following incubation with Fe (II, Mn (II or Zn (II salts alone or in combination with PRE against any of the organisms in the test panel. The addition of vitamin C markedly enhanced the activities of both PRE/Fe (II and PRE/Cu (II combinations against S. aureus. Conclusion This is the first report demonstrating

  15. Daily intakes of alkaline earth metals in Japanese males

    International Nuclear Information System (INIS)

    Shiraishi, Kunio; Yamamoto, Masayoshi; Ueno, Kaoru

    1994-01-01

    Diet samples were collected for two duplicate portion studies and one market basket study. 226 Ra in the diet samples was determined by alpha spectrometry and daily intake was estimated as 23 mBq (0.62 pCi) per person. Other alkaline earth metals were determined by inductively coupled plasma atomic-emission spectrometry. Average mineral intakes of calcium, magnesium, strontium, and barium were 0.55 g, 0.21 g, 2.3 mg, and 0.39 mg, respectively. Element ratios magnesium:calcium 0.38, strontium:calcium 4.2 x 10 -3 barium:calcium 7.1 X 10 -4 , and Ra:calcium 1.1 x 10 -12 were found in the diet; these compared with element ratios in Japanese vertebrae of magnesium:calcium 0.011, strontium:calcium 3.1 x 10 -4 , barium:calcium 2.7 x 10 -5 , and radium:calcium 2.6 x 10 -14 . Observed ratios, defined as the element ratio in bone divided by the respective element intake ratio in Japanese males, were as follows: 226 Ra 0.02, magnesium 0.03, strontium 0.07, and barium 0.04

  16. Mixed insoluble acidic salts of tetravalent metals Pt. 5

    International Nuclear Information System (INIS)

    Shakshooki, S.K.; Dehair, A.; Elmismary, Y.; Haraga, S.; Benfaid, N.; Benhamed, A.; Maiof, A.; Szirtes, L.

    1988-01-01

    Solid ZrOCl 2 x8H 2 O was added in a slow stream to a solution of phosphoric acid or to a solution of TiCl 4 in phosphoric acid to obtain granules of amorphous Zr(HPO 4 ) 2 xnH 2 O or Zr x Ti (1-x) (HPO 4 ) 2 xnH-2O (where x=0.95-0.80). It was found that the particle size of the resulting materials is very similar to that of ZrOCl 2 x8H 2 O, in such a way that it may be controlled indirectly. These materials are suitable for ion-exchange column operations. The relatively high gamma radiation doses of 60 Co source did not alter its exchange properties. pH-titrations were performed by an automatic titrimeter and the exchange capacities of alkali metal ions were determined by isotopic tracer technique. Other characterizations were made by usual chemical analysis and thermography. (author) 20 refs.; 4 figs

  17. Effects of Salts and Metal Oxides on Electrochemical and Optical Properties of Streptococcus mutans

    Science.gov (United States)

    Kawai, Tsuyoshi; Nagame, Seigo; Kambara, Masaki; Yoshino, Katsumi

    1994-10-01

    The effects of calcium salts and metal oxide powders on electrochemical, optical and biological properties of Streptococcus mutans have been studied as a novel method to determine the strain. Electrochemical signals of Streptococcus mutans show remarkable decrease in the presence of saturated calcium salts such as CaHPO4, Ca3(PO4)2, and Ca5(PO4)3OH depending on the strains of Streptococcus mutans: Ingbritt, NCTC-10449, or GS-5. The number of viable cells also decreases upon addition of these powders. The effects of metal oxides such as ZnO and BaTiO3 on the electrochemical characteristics and photoluminescence of Streptococcus mutans have also been studied.

  18. Chemistry of solvent extraction of rare metals by quaternary ammonium salts

    International Nuclear Information System (INIS)

    Stepanov, S.I.

    1996-01-01

    An investigation of the liquid-liquid extraction of Ti, Nb,Ta, Cr(VI), Mo(VI), W(VI), U(VI), Th(lV), Sc, Y and lanthanoids, as well as mineral acids and alkaline metals, using quaternary ammonium salts, alone, and with mixtures of other classes of extractants is reported. The composition of extracted compounds and the mechanism of their extraction are discussed

  19. Swelling compositions based polycarboxylic acids and bentonite clays in solutions of salts of metals

    Directory of Open Access Journals (Sweden)

    A. Sarshesheva

    2012-12-01

    Full Text Available This work is devoted to the synthesis of chemical cross-linked composite materials made of natural inorganic polymer bentonite clay of Manrak deposit, and polyacrylic and polymethacrylic acids. The swelling ability of the composition in solutions of salts of heavy metals (Ni2+ and Pb2+, influence of solution of concentration, pH and temperature on the swelling ability is investigated.

  20. Dependence of capacitance of metal-molten salt interface on local density profiles near electrode

    International Nuclear Information System (INIS)

    Ballone, P.; Pastore, G.; Tosi, M.P.; Painter, K.R.; Grout, P.J.; March, N.H.

    1983-09-01

    The mean spherical approximation applied to a metal-molten salt interface is generalized to take further account of the local density profiles near the electrode. The temperature dependence of the differential capacitance is shown to arise, in large measure from such local structure. However, the hard wall assumption for the electrode is retained and this must be kept in mind in comparing our model results with experiment. (author)

  1. Regioselective hydrogen isotope exchange reaction in benzoic acid and its alkali metal salts

    International Nuclear Information System (INIS)

    Nakagawa, Akiko; Hasegawa, Hideaki; Oohashi, Kunio; Seki, Hiroko.

    1997-01-01

    The hydrogen isotope exchange reaction of benzoic and acid its alkali metal salts with deuterium oxide was studied in the presence of RhCl 3 ·3H 2 O. The products were analyzed by 1 H- and 13 C-NMR spectroscopies. High regioselectivity of the exchange at the ortho positions was established, and the extent of deuterium labeling and the distribution of d 0 , d 1 , and d 2 were determined. The reaction mechanism was briefly discussed. (author)

  2. Molten salt electrolytic reduction of metal oxides with a view to the processing of nuclear materials

    International Nuclear Information System (INIS)

    Schwandt, Carsten

    2014-01-01

    The winning of metals from their oxides is a subject of huge academic and industrial interest. Molten salt technologies play a key role in this field, as evidenced by the long-established and mature technologies used for the winning of metals such as aluminium, magnesium, lithium and sodium and several others. The objective of this contribution is to review the key features of the FFC Cambridge process, highlight its general advantages and unique versatility and, finally, emphasise its relevance in the reprocessing of spent oxide nuclear fuel in the context of establishing viable nuclear technologies for the future

  3. Nucleophilic substitution and oxidative coupling in reaction of metallated lithium salt of acetic acid with 1,2-dibromoethane

    OpenAIRE

    Chanysheva, A.; Zorin, A.; Klimakov, V.; Spirikhin, L.; Zorin, V.

    2009-01-01

    When lithium salt of acetic acid metallated by lithium diisopropylamide in tetrahydrofuran interacts with 1,2-dibromoethane products of nucleophilic substitution of bromine atoms for oxycarbomethyl group and oxidative coupling of acetoxydianions are obtained.

  4. When VSEPR fails: experimental and theoretical investigations of the behavior of alkaline-earth-metal acetylides.

    Science.gov (United States)

    Guino-o, Marites A; Alexander, Jacob S; McKee, Michael L; Hope, Håkon; Englich, Ulrich B; Ruhlandt-Senge, Karin

    2009-11-09

    The synthesis, structural, and spectral characterization as well as a theoretical study of a family of alkaline-earth-metal acetylides provides insights into synthetic access and the structural and bonding characteristics of this group of highly reactive compounds. Based on our earlier communication that reported unusual geometry for a family of triphenylsilyl-substituted alkaline-earth-metal acetylides, we herein present our studies on an expanded family of target derivatives, providing experimental and theoretical data to offer new insights into the intensively debated theme of structural chemistry in heavy alkaline-earth-metal chemistry.

  5. Study of borehole plugging in bedded salt domes by earth melting technology

    International Nuclear Information System (INIS)

    Black, D.L.

    1975-06-01

    The intent of this program is to define the most viable Melted In situ Rock salt Plug (MIRP) System options, these options being addressed primarily from the downhole subsystem perspective, with a conventional drill rig as the basis for the surface part of the MIRP System. Preliminary experiments had indicated that it is possible to backfill the open penetrations in the domed salt deposits with a melted in situ rocksalt plug such that in time the melted rock salt plug effectively duplicates the parent virgin salt. The programmatic assumption for the requirement of duplicating the virgin salt with a MIRP provides the basis for this study. A system functional analysis was performed to establish the requirements for the performance of the overall MIRP System. A similar functional analysis was conducted for the salt plug that would be formed by the MIRP System. Based on the analyses of the material, thermal, and structural behavior of the salt plug, the requirements for the formation of an acceptable salt plug were determined. From the functional analysis a determination was made of the operation of the hardware for the downhole portion of the MIRP System. From that perspective several design concepts were formulated. For these design concepts a technology roadmap was developed. The pertinent aspects, results, conclusions and recommendations of the above are summarized in the sections that follow

  6. Trace metals behaviour during salt and fresh water mixing in the Venice Lagoon

    International Nuclear Information System (INIS)

    Ghermandi, G.; Campolieti, D.; Cecchi, R.; Costa, F.; Zaggia, L.; Zonta, R.

    1993-01-01

    Preliminary results of an investigation on trace metals behaviour in the estuarine system of the Dese River (Venice Lagoon) are described. Hydrodynamical and water chemical-physical measurements and PIXE concentrations analysis on size-fractionated samples emphasize the complexity of the processes occurring in the area of salt and fresh water mixing. Suspended load variations in the bottom layer of the water column, which may be mostly ascribed to resuspension, regulate the trace metal concentrations and seem to play a fundamental role in the transport of pollutants in shallow water areas of the estuary. The behaviour of dissolved metals is masked by the presence of suspended matter, but some relationships with chemical-physical variables are distinguishable, furnishing information on the processes affecting their concentration in the system. (orig.)

  7. Standard practice for determining cracking susceptibility of metals exposed under stress to a hot salt environment

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1990-01-01

    1.1 This practice covers procedures for testing metals for embrittlement and cracking susceptibility when exposed under stress to a hot salt environment. This practice can be used for testing all metals for which service conditions dictate the need for such information. The test procedures described herein are generally applicable to all metal alloys; required adjustments in environmental variables (temperature, stress) to characterize a given materials system should be made. This practice describes the environmental conditions and degree of control required, and suggests means for obtaining this desired control. 1.2 This practice can be used both for alloy screening for determination of relative susceptibility to embrittlement and cracking, and for the determination of time-temperature-stress threshold levels for onset of embrittlement and cracking. However, certain specimen types are more suitable for each of these two types of characterizations. Note 1 This practice relates solely to the performance of ...

  8. Lithium salts for advanced lithium batteries: Li–metal, Li–O2, and Li–S

    DEFF Research Database (Denmark)

    Younesi, Reza; Veith, Gabriel M.; Johansson, Patrik

    2015-01-01

    Presently lithium hexafluorophosphate (LiPF6) is the dominant Li-salt used in commercial rechargeable lithium-ion batteries (LIBs) based on a graphite anode and a 3–4 V cathode material. While LiPF6 is not the ideal Li-salt for every important electrolyte property, it has a uniquely suitable...... combination of properties (temperature range, passivation, conductivity, etc.) rendering it the overall best Li-salt for LIBs. However, this may not necessarily be true for other types of Li-based batteries. Indeed, next generation batteries, for example lithium–metal (Li–metal), lithium–oxygen (Li–O2......), and lithium–sulfur (Li–S), require a re-evaluation of Li-salts due to the different electrochemical and chemical reactions and conditions within such cells. This review explores the critical role Li-salts play in ensuring in these batteries viability....

  9. When VSEPR Fails: Experimental and Theoretical Investigations of the Behavior of Alkaline-Earth-Metal Acetylides

    OpenAIRE

    Guino-o, Marites A.; Alexander, Jacob S.; McKee, Michael L.; Hope, Håkon; Englich, Ulrich B.; Ruhlandt-Senge, Karin

    2009-01-01

    The synthesis, structural, and spectral characterization as well as a theoretical study of a family of alkaline-earth-metal acetylides provides insights into synthetic access and the structural and bonding characteristics of this group of highly reactive compounds. Based on our earlier communication that reported unusual geometry for a family of triphenylsilyl-substituted alkaline-earth-metal acetylides, we herein present our studies on an expanded family of target derivatives, providing expe...

  10. Mass-spectrometric investigation of thermal dissociation of alkaline earth metal monophosphates

    International Nuclear Information System (INIS)

    Lopatin, S.I.; Semenov, G.A.

    1989-01-01

    By the Knudsen effusion method with mass-spectrometric analysis of vapour phase, processes of thermal dissociation of Mg, Ca, Sr and Ba monophosphates have been studied. It is shown that vapour composition over alkaline-earth metal monophoshates depends on the compsition of condensed phase and volatility of alkaline-earth metal oxides. Dependences of partial pressures of vapour components on the temperature and duration of the experiment are given

  11. The recent development of efficient Earth-abundant transition-metal nanocatalysts.

    Science.gov (United States)

    Wang, Dong; Astruc, Didier

    2017-02-06

    Whereas noble metal compounds have long been central in catalysis, Earth-abundant metal-based catalysts have in the same time remained undeveloped. Yet the efficacy of Earth-abundant metal catalysts was already shown at the very beginning of the 20th century with the Fe-catalyzed Haber-Bosch process of ammonia synthesis and later in the Fischer-Tropsch reaction. Nanoscience has revolutionized the world of catalysis since it was observed that very small Au nanoparticles (NPs) and other noble metal NPs are extraordinarily efficient. Therefore the development of Earth-abundant metals NPs is more recent, but it has appeared necessary due to their "greenness". This review highlights catalysis by NPs of Earth-abundant transition metals that include Mn, Fe, Co, Ni, Cu, early transition metals (Ti, V, Cr, Zr, Nb and W) and their nanocomposites with emphasis on basic principles and literature reported during the last 5 years. A very large spectrum of catalytic reactions has been successfully disclosed, and catalysis has been examined for each metal starting with zero-valent metal NPs followed by oxides and other nanocomposites. The last section highlights the catalytic activities of bi- and trimetallic NPs. Indeed this later family is very promising and simultaneously benefits from increased stability, efficiency and selectivity, compared to monometallic NPs, due to synergistic substrate activation.

  12. Soluble salts: their incidence on the protection of metallic structures by paint coatings

    Directory of Open Access Journals (Sweden)

    Morcillo, M.

    2003-12-01

    Full Text Available The presence of soluble salts at the metal/paint interface is known to have a detrimental effect on the integrity of most paint systems. Though this is a long-standing problem, it has recently come to receive greater attention from the protective coatings industry. In the paper the following points are reviewed: degradation mechanisms of the metal/paint system, the role of the metallic substrate, the nature, origin and detection of soluble salts, expected levels of soluble salts in practice, critical thresholds of soluble salts and risk levels for premature failures, role of the type and thickness of paint systems and exposure conditions, and prevention measures. The author presents an overview of the subject, making reference to the related research that has been carried out by him and his coworkers over the last 16 years.

    Es un hecho conocido que la presencia de sales solubles en la intercara metal/pintura tiene un efecto negativo sobre la mayoría de los sistemas de pintura. Aunque se trata de un problema conocido desde hace tiempo, ha sido recientemente cuando ha recibido una gran atención por parte de la industria de recubrimientos protectores. En el presente trabajo se revisan los siguientes aspectos: mecanismos de degradación del sistema metal/pintura, el papel que juega el substrato metálico, la naturaleza, origen y detección de las sales solubles, niveles esperados de sales solubles en la práctica, niveles críticos de sales solubles y niveles de riesgo de fallo prematuro del sistema de pintura, papel que juega el tipo y espesor del sistema de pintura, el ambiente de exposición y las medidas de prevención. El autor presenta una revisión del tema, haciendo referencia a los trabajos de investigación que ha llevado a cabo, junto con su grupo de investigación, durante los últimos 16 años.

  13. Activation and discovery of earth-abundant metal catalysts using sodium tert-butoxide.

    Science.gov (United States)

    Docherty, Jamie H; Peng, Jingying; Dominey, Andrew P; Thomas, Stephen P

    2017-06-01

    First-row, earth-abundant metals offer an inexpensive and sustainable alternative to precious-metal catalysts. As such, iron and cobalt catalysts have garnered interest as replacements for alkene and alkyne hydrofunctionalization reactions. However, these have required the use of air- and moisture-sensitive catalysts and reagents, limiting both adoption by the non-expert as well as applicability, particularly in industrial settings. Here, we report a simple method for the use of earth-abundant metal catalysts by general activation with sodium tert-butoxide. Using only robust air- and moisture-stable reagents and pre-catalysts, both known and, significantly, novel catalytic activities have been successfully achieved, covering hydrosilylation, hydroboration, hydrovinylation, hydrogenation and [2π+2π] alkene cycloaddition. This activation method allows for the easy use of earth-abundant metals, including iron, cobalt, nickel and manganese, and represents a generic platform for the discovery and application of non-precious metal catalysis.

  14. The Equilibrium Between Titanium Ions and Titanium Metal in NaCl-KCl Equimolar Molten Salt

    Science.gov (United States)

    Wang, Qiuyu; Song, Jianxun; Hu, Guojing; Zhu, Xiaobo; Hou, Jungang; Jiao, Shuqiang; Zhu, Hongmin

    2013-08-01

    The equilibrium between metallic titanium and titanium ions, 3Ti2+ ⇌ 2Ti3+ + Ti, in NaCl-KCl equimolar molten salt was reevaluated. At a fixed temperature and an initial concentration of titanium chloride, the equilibrium was achieved by adding an excess amount of sponge titanium in assistant with bubbling of argon into the molten salt. The significance of this work is that the accurate concentrations of titanium ions have been obtained based on a reliable approach for taking samples. Furthermore, the equilibrium constant {{K}}_{{C}} = (x_{{{{Ti}}^{{ 3 { + }}} }}^{{eql}} )3 /(x_{{{{Ti}}^{{ 2 { + }}} }}^{{eql}} )2 was calculated through the best-fitting method under the consideration of the TiOCl dissolution. Indeed, the final results have disclosed that the stable value of KC could be achieved based on all modifications.

  15. Insights into the Metal Salt Catalyzed 5-Ethoxymethylfurfural Synthesis from Carbohydrates

    Directory of Open Access Journals (Sweden)

    Xin Yu

    2017-06-01

    Full Text Available The use of common metal salts as catalysts for 5-ethoxymethylfurfural (EMF synthesis from carbohydrate transformation was performed. Initial screening suggested AlCl3 as an efficient catalyst for EMF synthesis (45.0% from fructose at 140 °C. Interestingly, CuSO4 and Fe2(SO43 were found to yield comparable EMF at lower temperature of 110 to 120 °C, and high yields of ethyl levulinate (65.4–71.8% were obtained at 150 °C. However, these sulfate salts were inactive in EMF synthesis from glucose and the major product was ethyl glucoside with around 80% yield, whereas EMF of 15.2% yield could be produced from glucose using CrCl3. The conversion of sucrose followed the accumulation of the reaction pathways of fructose and glucose, and a moderate yield of EMF could be achieved.

  16. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite for methanol synthesis

    Science.gov (United States)

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1993-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  17. Synthesis and infrared spectra of alkaline earth metal carbonates ...

    Indian Academy of Sciences (India)

    Unknown

    ... Sr2+ and Ba2+ salts with urea at high temperature, ~ 80°C. The reaction products were characterized through elemental analysis and infrared spectra. The infrared spectra of the products are the same as those of the corresponding commercially obtained carbonates. A general reaction describing the formation of MCO3 ...

  18. Caprylate Salts Based on Amines as Volatile Corrosion Inhibitors for Metallic Zinc: Theoretical and Experimental Studies.

    Science.gov (United States)

    Valente, Marco A G; Teixeira, Deiver A; Azevedo, David L; Feliciano, Gustavo T; Benedetti, Assis V; Fugivara, Cecílio S

    2017-01-01

    The interaction of volatile corrosion inhibitors (VCI), caprylate salt derivatives from amines, with zinc metallic surfaces is assessed by density functional theory (DFT) computer simulations, electrochemical impedance (EIS) measurements and humid chamber tests. The results obtained by the different methods were compared, and linear correlations were obtained between theoretical and experimental data. The correlations between experimental and theoretical results showed that the molecular size is the determining factor in the inhibition efficiency. The models used and experimental results indicated that dicyclohexylamine caprylate is the most efficient inhibitor.

  19. A study of metallic coatings obtained by electrolysis of molten salts

    International Nuclear Information System (INIS)

    Broc, Michel.

    1978-06-01

    An appropriate technique has been developed for obtaining compact metallic coatings from electrolysis of molten salts. Through the use of this method, it has been possible to produce pure metal deposits which, until now, has been extremely difficult to do. The apparatus used and the main steps of the process such as dehydration of the solvant, degassing of the equipment, and starting of the electrolytic process, are first described. This is followed by a discussion of the deposits of the metals beryllium, uranium, tantalum and tungsten obtained from electrolysis of molten fluorides at temperatures between 600 and 800 0 C. The metal coatings so obtained are homogeneous and show continuity, their thicknesses varying from a few microns to a millimeter or more. They have been studied by measurements. As potential applications of this new technique, one can mention the growth of diffusion barriers and the production of cathodes for thermoionic emission. The method can also be used for electroforming. An intermetallic diffusion between the deposit and the substrate has been observed in some cases. The advantage of the technique of melt electrolysis in obtaining metal coatings of enhanced thicknesses is illustrated by taking the beryllium-nickel system as an example. It is shown that the thickness obtained is proportional to the square root of growth time and is about 6 to 8 times larger than that obtained by conventional techniques [fr

  20. Antitumor Activity and Toxicity of Salts of Inorganic Group IIIa Metals: Aluminum, Gallium, Indium, and Thallium

    Science.gov (United States)

    Hart, Michael M.; Adamson, Richard H.

    1971-01-01

    The toxicity and antitumor activity of salts of the Group IIIa metals aluminum, gallium, indium, and thallium were determined. With the (lethal dose)50 as a measure, the decreasing order of toxicity was TlCl3 ≥ In(NO3)3 > Ga(NO3)3 > Al(NO3)3. All four metals exhibited antitumor activity, but when the tumor was inoculated by a route different from that of the drug, only Ga+3 and, to a lesser extent, In+3 inhibited tumor growth. Ga(NO3)3 was found to inhibit the growth of three out of four rodent solid tumors. Gallium therefore has potential therapeutic usefulness for treatment of solid tumors in man. PMID:5283954

  1. Indirect, reversible high-density hydrogen storage in compact metal ammine salts

    DEFF Research Database (Denmark)

    Sørensen, Rasmus Zink; Hummelshøj, Jens Strabo; Klerke, Asbjørn

    2008-01-01

    structures develop, which facilitates desorption from the interior of large, compact tablets. Density functional theory calculations reproduce trends in desorption enthalpies for the systems studied, and a mechanism in which individual chains of the ammines are released from the surface of the crystal......The indirect hydrogen storage capabilities of Mg(NH3)(6)Cl-2, Ca(NH3)(6)Cl-2, Mn(NH3)(6)Cl-2, and Ni(NH3)(6)Cl-2 are investigated. All four metal ammine chlorides can be compacted to solid tablets with densities of at least 95% of the crystal density. This gives very high indirect hydrogen...... densities both gravimetrically and volumetrically. Upon heating, NH3 is released from the salts, and by employing an appropriate catalyst, H-2 can be released corresponding to up to 9.78 wt % H and 0.116 kg H/L for the Ca(NH3)(8)Cl-2 salt. The NH3 release from all four salts is investigated using...

  2. Crystal Fields in Dilute Rare-Earth Metals Obtained from Magnetization Measurements on Dilute Rare-Earth Alloys

    DEFF Research Database (Denmark)

    Touborg, P.; Høg, J.

    1974-01-01

    Crystal field parameters of Tb, Dy, and Er in Sc, Y, and Lu are summarized. These parameters are obtained from magnetization measurements on dilute single crystals, and successfully checked by a number of different methods. The crystal field parameters vary unpredictably with the rare-earth solut....... B40, B60, and B66 are similar in Y and Lu. Crystal field parameters for the pure metals Tb, Dy, and Er are estimated from the crystal fields in Y and Lu....

  3. Evaluation of quality of permanent teeth restorations in children of areas contaminated by heavy metal salts

    Directory of Open Access Journals (Sweden)

    V. V. Avakov

    2014-04-01

    Full Text Available The influence of the environment on the child health is one of priority issues of the present time and it is of great social importance. Increased dental diseases associated with climatic and geographical characteristics of the area are widely discussed in the literature. The leading among them are environmentally determined dental diseases in children associated with geochemical and technogenic pollution of the area where they live. Increasing amounts of hard metal salts is the urgent hygienic problem, due to severity of their multi-element analysis in microsubjects, and negative influence on health of the children population, due to tropism, ability to cumulation, long biological life in the body and antagonism of heavy metal salts to the number of microelements. Influence of hard metal salts on dental diseases development is undeniable. Particular attention is paid to their influence on caries process and treatment peculiarities. Despite the fact that modern аdhesive dentistry in recent years has made a significant breakthrough in improving adhesive systems, correct choice of adhesive system depending on changes in the structure of hard tissue under geochemical contaminants (like heavy metal salts is the most important step. It is the decisive factor for adaptation and connection of restoration with the restoration base. We should remember that on the way of adhesive system there is an altered structure preventing from deep penetration of such system and, consequently, leading to violation of restoration tightness. Therefore, early detection of complications by clinical evaluation of quality of the restorations is of great interest. Multi-vector approach to treatment of dental caries in children living in conditions of technogenic pollution by heavy metal salts is extremely urgent and important issue. Significant niche in this approach is given to adhesive preparation methods combined with local fluoridation, using fluoride medication of the

  4. Crystalline and amorphous rare-earth metallic compounds

    International Nuclear Information System (INIS)

    Burzo, E.

    1975-01-01

    During the last years the study of magnetic behaviour of rare-earth (or yttrium) compounds with cobalt and iron has growth of interest. This interest of justified by a large area of experimental and theoretical problems coming into being in the study of some rare-earth materials as well as in their technical applications. In the last three years a great number of new rare earth materials were studied and also new models explaining the magnetic behaviour of these systems have been used. In this paper we refer especially to some typical systems in order to analyse the magnetic behaviour of iron and cobalt and also the part played by the magnetic interactions in the values of the cobalt or iron moments. The model used will be generally the molecular field model. In the second chapter we present comparatively the structure of crystalline and amorphous compounds for further correlation with the magnetic properties. In chapter III we analyse the magnetic interactions in some crystalline and amorphous rare-earth alloys. Finally, we exemplify the ways in which we ensure better requried characteristics by the technical utilizations of these materials. These have in view the modifications of the magnetic interactions and are closely related with the analysis made in chapter III

  5. Coprecipitation of rare earths in systems of three heterovalent ions with sulfates of alkali and alkaline-earth metals

    International Nuclear Information System (INIS)

    Bobrik, V.M.

    1977-01-01

    Co-precipitation of rare earth elements (REE) in milligram amounts (3x10 -3 -3x10 -1 M) with alkali earth (AEE) sulfates in presence of alkali metal ions has been studied, the AEE:REE ratios between the co-precipitator and a REE (up to 50:1) the latter can be co-precipitated quantitatively in presence of corresponding alkali metals linked with the AEE in the Periodic table by a diagonal, i.e. in presence of sodium in co-precipitation with calcium sulfate, potassium with strontium sulfate and rubidium with barium sulfate. Co-precipitation with sulfates of sodium and calcium occurs at temperatures above 85 deg C and presumably involves calcium semihydrate. In presence of an alkali metal REE co-precipitation with AEE becomes isomorphic, i.e. at different AEE:REE ratios the co-precipitation coefficient remains constant. In presence of corresponding alkali metals the decrease in effectiveness of co-precipitation with AEE in the La-Lu series is more pronounced

  6. THE DISTRIBUTION OF COMMERCIAL CROWN ETHER DC18C6 AND THE EXTRACTION STUDY OF ALKALI AND EARTH ALKALI METALS

    Directory of Open Access Journals (Sweden)

    Bambang Rusdiarso

    2010-06-01

    Full Text Available Distribution of A and B isomers of crown-ether DC18C6 on their organic and water phases (chloride, nitrate and sulphocyanide salts and extraction of alkali and earth alkali metals has been studied. In LiCl 0.1 M environment, lithium extraction could be ignored. The presence of extracted potassium metal may affect the crown ether DC18C6 distribution albeit only a little. In KNO3 0.1 M environment, the distribution coefficient values (d were 6.1 and 10.3 for A and B isomers, respectively ; while in KCl  0.1 M environment the values were 4.9 and 11.8, respectively. In KSCN 0.1 M, d values for A and B isomers were 40.4 and 36.6, respectively, which were higher than the value obtained from both KNO3 and KCl  0.1 M environments. Caesium metal extraction using DC18C6 occurred weakly, up to only 5%. Strontium extraction using DC18C6 achieved better yield than the caesium extraction. The percentage of extraction increased under organic solvent according to the following: toluene (4% < chloroform (28% < TBP (35%.   Keywords: distribution, crown-ether DC18C6, extraction.

  7. Endonuclease active site plasticity allows DNA cleavage with diverse alkaline Earth and transition metal ions.

    Science.gov (United States)

    Vasu, Kommireddy; Saravanan, Matheshwaran; Nagaraja, Valakunja

    2011-09-16

    A majority of enzymes show a high degree of specificity toward a particular metal ion in their catalytic reaction. However, Type II restriction endonuclease (REase) R.KpnI, which is the first member of the HNH superfamily of REases, exhibits extraordinary diversity in metal ion dependent DNA cleavage. Several alkaline earth and transition group metal ions induce high fidelity and promiscuous cleavage or inhibition depending upon their concentration. The metal ions having different ionic radii and co-ordination geometries readily replace each other from the enzyme's active site, revealing its plasticity. Ability of R.KpnI to cleave DNA with both alkaline earth and transition group metal ions having varied ionic radii could imply utilization of different catalytic site(s). However, mutation of the invariant His residue of the HNH motif caused abolition of the enzyme activity with all of the cofactors, indicating that the enzyme follows a single metal ion catalytic mechanism for DNA cleavage. Indispensability of His in nucleophile activation together with broad cofactor tolerance of the enzyme indicates electrostatic stabilization function of metal ions during catalysis. Nevertheless, a second metal ion is recruited at higher concentrations to either induce promiscuity or inhibit the DNA cleavage. Regulation of the endonuclease activity and fidelity by a second metal ion binding is a unique feature of R.KpnI among REases and HNH nucleases. The active site plasticity of R.KpnI opens up avenues for redesigning cofactor specificities and generation of mutants specific to a particular metal ion.

  8. Do salt and low temperature impair metal treatment in stormwater bioretention cells with or without a submerged zone?

    Science.gov (United States)

    Søberg, Laila C; Viklander, Maria; Blecken, Godecke-Tobias

    2017-02-01

    Although seasonal temperature changes and (road) salt in winter and/or coastal stormwater runoff might interfere with the metal treatment performance of stormwater bioretention cells, no previous study has evaluated the effect of these factors and their interactions under controlled conditions. In this 18week long study 24 well established pilot-scale bioretention columns were employed to evaluate the individual and combined effect(s) of low/high temperature, salt and presence of a submerged zone with an embedded carbon source on metal removal using a three factor, two-level full factorial experimental design. In most instances, the three factors significantly influenced the metal outflow concentrations and thus the treatment performance; the effect of temperature depended on the metal in question, salt had an overall negative effect and the submerged zone with carbon source had an overall positive effect. Despite these statistically significant effects, the discharge water quality was generally markedly improved. However, leaching of dissolved Cu and Pb did occur, mainly from bioretention cells dosed with salt-containing stormwater. The highest concentrations of metals were captured in the top layer of the filter material and were not significantly affected by the three factors studied. Overall, the results confirmed that bioretention provides a functioning stormwater treatment option in areas experiencing winter conditions (road salt, low temperatures) or coastal regions (salt-laden stormwater). However, validation of these results in the field is recommended, especially focusing on dissolved metal removal, which may be critically affected under certain conditions. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Maternal exposure to alkali, alkali earth, transition and other metals: Concentrations and predictors of exposure.

    Science.gov (United States)

    Hinwood, A L; Stasinska, A; Callan, A C; Heyworth, J; Ramalingam, M; Boyce, M; McCafferty, P; Odland, J Ø

    2015-09-01

    Most studies of metals exposure focus on the heavy metals. There are many other metals (the transition, alkali and alkaline earth metals in particular) in common use in electronics, defense industries, emitted via combustion and which are naturally present in the environment, that have received limited attention in terms of human exposure. We analysed samples of whole blood (172), urine (173) and drinking water (172) for antimony, beryllium, bismuth, cesium, gallium, rubidium, silver, strontium, thallium, thorium and vanadium using ICPMS. In general most metals concentrations were low and below the analytical limit of detection with some high concentrations observed. Few factors examined in regression models were shown to influence biological metals concentrations and explained little of the variation. Further study is required to establish the source of metals exposures at the high end of the ranges of concentrations measured and the potential for any adverse health impacts in children. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

  10. Environmental Defects And Economic Impact On Global Market Of Rare Earth Metals

    Science.gov (United States)

    Charalampides, G.; Vatalis, K.; Karayannis, V.; Baklavaridis, A.

    2016-11-01

    Rare earth elements include the 14 lanthanides as well as lanthanium and often yttrium. Actually, most of them are not very rare and occur widely dispersed in a variety of rocks. Rare earth metals are vital to some of the world's faster growing industries: catalysts, Nd-magnets, ceramics, glass, metallurgy, battery alloys, electronics and phosphors. Worldwide, the main countries for distribution of rare earths deposits include China, USA, Russia, Brasil, India, Australia, Greenland and Malaysia. The mining and processing of rare earth metals usually result in significant environmental defects. Many deposits are associated with high concentrations of radioactive elements such as uranium and thorium, which requires separate treatment and disposal. The accumulation of rare earth elements in soils has occurred due to pollution caused by the exploitation of rare earth resources and the wide use of rare earths as fertilizers in agriculture. This accumulation has a toxic effect on the soil microfauna community. However, there are large differences in market prices due to the degree of purity determined by the specifications in the applications. The main focus of this article is to overview Rare Earth Metals’ overall impact on global economy and their environmental defects on soils during processing techniques and as they are used as fertilizers.

  11. Origin of uranium and rare earth minerals in bone detritus from rare metal deposits

    Science.gov (United States)

    Baturin, G. N.; Dubinchuk, V. T.

    2011-06-01

    In order to ascertain the forms in which uranium is present in ores of the Melovoe rare metal sedimentary deposit of uranium and rare earth minerals (South Mangyshlak), we investigated a series of typical ore samples that were collected earlier; both the uranium content and the total content of rare earth metals in them lay within 0.1-0.3%. The study was carried out by analytical electron microscopy using transmission electron microscopy and scanning electron microscopy, electron microdiffraction, and microprobing. It was ascertained that both uranium and rare earth elements are present in ore mostly associated with biogenic phosphate in the form of natural minerals, such as uraninite, ningyoite, coffinite, autenite, and churchite. Iron hydroxides and graphitized organic matter are present in some samples. It is assumed that the co-occurrence of uranium and rare earth elements, which is nontypical for the sedimentary process, resulted from secondary epigenetic processes and alternation of reducing and oxidizing environmental conditions.

  12. High-Field Magnetization of Light Rare-Earth Metals

    DEFF Research Database (Denmark)

    McEwen, K.A.; Cock, G.J.; Roeland, L.W.

    1973-01-01

    The magnetization of single crystals of Eu, Sm, Nd, Pr, and Pr-Nd alloys has been measured in fields up to 37 T (370 kG). The results give new information on the magnetic properties of these metals. Of particular interest is a first-order transition from a nonmagnetic to a metamagnetic phase in d...

  13. Contribution to the theoretical study of metallic systems containing rare earths: hyperfine interactions and exchange coupling

    International Nuclear Information System (INIS)

    Troper, A.

    1978-01-01

    A theoretical study involving rare earth impurities, which were embedded in transition metals (s-p or noble), from the point of view of the hyperfine interactions is presented. A model was created to describe a d-resonance (Anderson-Moriya) acting on a s-p conduction band which was strongly perturbed by a slater-koster potential, used to describe the rare earths which were diluted in matrices of transition elements. (author)

  14. Calculations in solvent extraction of rare earth metals

    International Nuclear Information System (INIS)

    Sadanandam, R.; Sharma, A.K.; Fonseca, M.F.; Hubli, R.C.; Suri, A.K.; Singh, D.K.

    2010-01-01

    The paper deals with calculation of number of countercurrent stages in solvent extraction of rare earths both under total reflux and partial reflux conditions to achieve a given degree of purification and recovery. The use of Fenske's equation normally used for separation by distillation is proposed to calculate the number of stages required under total reflux, replacing relative volatility by separation factor. Kremser's equations for extraction and scrubbing are used to calculate the number of stages in extraction and scrubbing modules under partial reflux conditions. McCabe-Thiele's approach is also adopted to arrive at the number of scrubbing stages. (author)

  15. SEQUESTERING AGENTS FOR METAL IMMOBILIZATION APPLICATION TO THE DEVELOPMENT OF ACTIVE CAPS IN FRESH AND SALT WATER SEDIMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Knox, A; Michael Paller, M

    2006-11-17

    This research evaluated the removal of inorganic contaminants by a variety of amendments and mixtures of amendments in fresh and salt water. A series of removal and retention batch experiments was conducted to identify the best treatment for metal removal. Metal removal by the amendments was evaluated by calculating the partition coefficient and percent removal. Retention of metals by the amendments was evaluated in retention (desorption) studies in which residue from the removal studies was extracted with 1 M MgCl{sub 2} solution. The results indicated that phosphate amendments, some organoclays (e.g., OCB-750), and the biopolymer, chitosan, are very effective in removal and retention of metals in both fresh and salt water. These amendments are being evaluated further as components in the development of active caps for sediment remediation.

  16. Localized corrosion of high performance metal alloys in an acid/salt environment

    Science.gov (United States)

    Macdowell, L. G.; Ontiveros, C.

    1991-01-01

    Various vacuum jacketed cryogenic supply lines at the Space Shuttle launch site at Kennedy Space Center use convoluted flexible expansion joints. The atmosphere at the launch site has a very high salt content, and during a launch, fuel combustion products include hydrochloric acid. This extremely corrosive environment has caused pitting corrosion failure in the thin walled 304L stainless steel flex hoses. A search was done to find a more corrosion resistant replacement material. The study focussed on 19 metal alloys. Tests which were performed include electrochemical corrosion testing, accelerated corrosion testing in a salt fog chamber, and long term exposure at a beach corrosion testing site. Based on the results of these tests, several nickel based alloys were found to have very high resistance to this corrosive environment. Also, there was excellent agreement between the electrochemical tests and the actual beach exposure tests. This suggests that electrochemical testing may be useful for narrowing the field of potential candidate alloys before subjecting samples to long term beach exposure.

  17. New technology of extracting the amount of rare earth metals from the red mud

    International Nuclear Information System (INIS)

    Martoyan, G A; Karamyan, G G; Vardan, G A

    2016-01-01

    The paper outlined the environmental and economic problems associated with red mud - the waste generated in processing of bauxite ore for aluminum production. The chemical analysis of red mud has identified a number of useful elements including rare earth metals. The electromembrane technology of red mud processing with extraction of valuable elements is described. A possible scheme of separation of these metals through electrolysis is also given. (paper)

  18. New technology of extracting the amount of rare earth metals from the red mud

    Science.gov (United States)

    Martoyan, G. A.; Karamyan, G. G.; Vardan, G. A.

    2016-01-01

    The paper outlined the environmental and economic problems associated with red mud - the waste generated in processing of bauxite ore for aluminum production. The chemical analysis of red mud has identified a number of useful elements including rare earth metals. The electromembrane technology of red mud processing with extraction of valuable elements is described. A possible scheme of separation of these metals through electrolysis is also given.

  19. Bridging the gap between ionic liquids and molten salts: group 1 metal salts of the bistriflamide anion in the gas phase.

    Science.gov (United States)

    Leal, João P; da Piedade, Manuel E Minas; Canongia Lopes, José N; Tomaszowska, Alina A; Esperança, José M S S; Rebelo, Luís Paulo N; Seddon, Kenneth R

    2009-03-19

    Fourier transform ion cyclotron resonance mass spectrometry experiments showed that liquid Group 1 metal salts of the bistriflamide anion undergoing reduced-pressure distillation exhibit a remarkable behavior that is in transition between that of the vapor-liquid equilibrium characteristics of aprotic ionic liquids and that of the Group 1 metal halides: the unperturbed vapors resemble those of aprotic ionic liquids, in the sense that they are essentially composed of discrete ion pairs. However, the formation of large aggregates through a succession of ion-molecule reactions is closer to what might be expected for Group 1 metal halides. Similar experiments were also carried out with bis{(trifluoromethyl)sulfonyl}amine to investigate the effect of H(+), which despite being the smallest Group 1 cation, is generally regarded as a nonmetal species. In this case, instead of the complex ion-molecule reaction pattern found for the vapors of Group 1 metal salts, an equilibrium similar to those observed for aprotic ionic liquids was observed.

  20. Maternal exposure to alkali, alkali earth, transition and other metals: Concentrations and predictors of exposure

    International Nuclear Information System (INIS)

    Hinwood, A.L.; Stasinska, A.; Callan, A.C.; Heyworth, J.; Ramalingam, M.; Boyce, M.; McCafferty, P.; Odland, J.Ø.

    2015-01-01

    Most studies of metals exposure focus on the heavy metals. There are many other metals (the transition, alkali and alkaline earth metals in particular) in common use in electronics, defense industries, emitted via combustion and which are naturally present in the environment, that have received limited attention in terms of human exposure. We analysed samples of whole blood (172), urine (173) and drinking water (172) for antimony, beryllium, bismuth, cesium, gallium, rubidium, silver, strontium, thallium, thorium and vanadium using ICPMS. In general most metals concentrations were low and below the analytical limit of detection with some high concentrations observed. Few factors examined in regression models were shown to influence biological metals concentrations and explained little of the variation. Further study is required to establish the source of metals exposures at the high end of the ranges of concentrations measured and the potential for any adverse health impacts in children. - This study has demonstrated exposure to alkali, alkali earth and transition metals in pregnant women with factors such as breastfeeding, fish oil use and diet affecting exposures

  1. Adsorption of alkali, alkaline-earth, and 3d transition metal atoms on silicene

    Science.gov (United States)

    Sahin, H.; Peeters, F. M.

    2013-02-01

    The adsorption characteristics of alkali, alkaline-earth, and transition metal adatoms on silicene, a graphene-like monolayer structure of silicon are analyzed by means of first-principles calculations. In contrast to graphene, interaction between the metal atoms and the silicene surface is quite strong due to its highly reactive buckled hexagonal structure. In addition to structural properties, we also calculate the electronic band dispersion, net magnetic moment, charge transfer, work function, and dipole moment of the metal adsorbed silicene sheets. Alkali metals, Li, Na, and K, adsorb to hollow sites without any lattice distortion. As a consequence of the significant charge transfer from alkalis to silicene, metalization of silicene takes place. Trends directly related to atomic size, adsorption height, work function, and dipole moment of the silicene/alkali adatom system are also revealed. We found that the adsorption of alkaline-earth metals on silicene is entirely different from their adsorption on graphene. The adsorption of Be, Mg, and Ca turns silicene into a narrow gap semiconductor. Adsorption characteristics of eight transition metals Ti, V, Cr, Mn, Fe, Co, Mo, and W are also investigated. As a result of their partially occupied d orbital, transition metals show diverse structural, electronic, and magnetic properties. Upon the adsorption of transition metals, depending on the adatom type and atomic radius, the system can exhibit metal, half-metal, and semiconducting behavior. For all metal adsorbates, the direction of the charge transfer is from adsorbate to silicene, because of its high surface reactivity. Our results indicate that the reactive crystal structure of silicene provides a rich playground for functionalization at nanoscale.

  2. The history of metals pollution in Narragansett Bay as recorded by salt-marsh sediments

    International Nuclear Information System (INIS)

    Bricker, S.B.

    1990-01-01

    Sediment cores from 5 salt marshes from the head to the mouth of Narragansett Bay and an additional core from a lagoon on Block Island Sound were analyzed for 210 Pb and for Fe, Mn, Cu, Pb, Cr, Zn, Ag, and Ni in order to examine the long-term variation of metal inputs to Narragansett Bay. The 210 Pb results were used to determine accretion rates for each core. Distributions of Fe and Mn were used as indicators of chemical conditions of sediment cores and Cu, Pb, Cr, Zn, Ag, and Ni distributions with time were compared with known or estimated source inputs to examine the long-term variation of pollutant metal inputs to Narragansett Bay. At one location, duplicate cores were sampled to look at variability within a marsh. At another location, a high marsh, receiving predominantly atmospheric inputs and a low marsh, receiving waterborne and atmospheric inputs, were sampled so that atmospheric and tidal contributions could be determined. A comparison was made of the distributions of metals in bay cores and in the lagoon core. All the Rhode Island marshes accrete at rates equal to or greater than the local rise in sea level. Based on the 210 Pb chronologies, pollutant metals began to increase in the mid to late 1800s, corresponding to coal burning emissions to the atmosphere. Steeper increases in the 1900s reflect industrial and sewage discharges. Maximum concentrations were reached in the 1950s and have declined almost continuously since then. Observed reductions were attributable to implementation of and improvements to sewage treatment, and controls on atmospheric emissions

  3. Aluminum/alkaline earth metal composites and method for producing

    Science.gov (United States)

    Russell, Alan M; Anderson, Iver E; Kim, Hyong J; Freichs, Andrew E

    2014-02-11

    A composite is provided having an electrically conducting Al matrix and elongated filaments comprising Ca and/or Sr and/or Ba disposed in the matrix and extending along a longitudinal axis of the composite. The filaments initially comprise Ca and/or Sr and/or Ba metal or allow and then may be reacted with the Al matrix to form a strengthening intermetallic compound comprising Al and Ca and/or Sr and/or Ba. The composite is useful as a long-distance, high voltage power transmission conductor.

  4. Rare-earth magnets applied to liquid metal flow

    International Nuclear Information System (INIS)

    Borges, E.M.; Sircilli Neto, F.; Passaro, A.

    1996-01-01

    The operation of electromagnetic pumps used to control liquid metal flow are based on the Lorentz force. In this work, it is studied the design of an electromagnetic pump substituting the C-type magnet used in a prototype built previously by Sm Co 5 permanent magnets. The results of the computational simulation indicate that the new pump can develop manometric pressure comparable to the previous prototype and also has smaller dimensions. Magnetic field measurement agreed with the magnetic simulation in the region of interest. (author)

  5. A study on the reduction of uranium oxide to uranium metal in LiCl molten salt

    International Nuclear Information System (INIS)

    Seo, J. S.; Hur, J. M.; Lee, W. K.; Hong, S. S.; Kang, D. S.; Park, S. W.

    2002-01-01

    Research for the analysis on a metallization process of uranium oxide in LiCl-Li molten salt was carried out. Effect of a concentration of Li 2 O on the metallization process was also studied. The new concept, electrochemical reduction of uranium oxide in LiCl-Li 2 O molten salt was proposed. The concept is based on the integrated process of metallization of UO 2 with simultaneous electrochemical reduction of Li 2 O which is recycled in a closed system. In a LiCl-Li molten salt system, U 3 O 8 whose conversion ratio to U turns out to be 97.1%, showed a better metallization characteristic than UO 2 . It is verified that electrochemically reduced Li is well deposited on the UO 2 powder cathode through a porous magnesia filter in LiCl-Li 2 O molten salt. In that process Li 2 O was from by the reduction process of UO 2 to U. This electrochemical reduction process showed good results to covert UO 2 to U

  6. Salt balance: From space experiments to revolutionizing new clinical concepts on earth - A historical review

    Science.gov (United States)

    Gerzer, Rupert

    2014-11-01

    For a long time, sodium balance appeared to be a ;done deal; and was thought to be well understood. However, experiments in preparation of space missions showed that the concept of osmotic sodium storage and close correlations of sodium with water balance are only part of the regulatory mechanisms of body salt. By now it has turned out that the human skin is an important storage place and regulator for sodium, that sodium storage involves macrophages which in turn salt-dependently co-regulate blood pressure, that body sodium also strongly influences bone and protein metabolism, and that immune functions are also strongly influenced by sodium. In addition, the aging process appears to lead to increased body sodium storage, which in turn might influence the aging process of the human body. The current review article summarizes the developments that have led to these revolutionizing new findings and concepts as well as consequences deriving from these findings. Therefore, it is not intended in this article to give a complete literature overview over the whole field but to focus on such key literature and considerations that led to the respective developments.

  7. Rare earth zirconium oxide buffer layers on metal substrates

    Science.gov (United States)

    Williams, Robert K.; Paranthaman, Mariappan; Chirayil, Thomas G.; Lee, Dominic F.; Goyal, Amit; Feenstra, Roeland

    2001-01-01

    A laminate article comprises a substrate and a biaxially textured (RE.sub.x A.sub.(1-x)).sub.2 O.sub.2-(x/2) buffer layer over the substrate, wherein 0layer can be deposited using sol-gel or metal-organic decomposition. The laminate article can include a layer of YBCO over the (RE.sub.x A.sub.(1-x)).sub.2 O.sub.2-(x/2) buffer layer. A layer of CeO.sub.2 between the YBCO layer and the (RE.sub.x A.sub.(1-x)).sub.2 O.sub.2-(x/2) buffer layer can also be include. Further included can be a layer of YSZ between the CeO.sub.2 layer and the (RE.sub.x A.sub.(1-x)).sub.2 O.sub.2-(x/2) buffer layer. The substrate can be a biaxially textured metal, such as nickel. A method of forming the laminate article is also disclosed.

  8. The heterogeneous reactions of silica, titania and zirconia with alkaline-earth metal oxides in metal chloride melts - to form alkaline-earth metal silicates titanates and zirconates. 1

    International Nuclear Information System (INIS)

    Packter, A.; Zaidi, S.A.

    1982-01-01

    The solubility versus temperature phase diagrams, for calcium, strontium and barium oxide (silicate and titanate) solutions in the metal chloride melts at 800 to 1400 0 C, have been analysed. The alkaline-earth metal oxide solutions are binary mixtures with solvate formation and the liquid phases probably contain [O . 4 MCl 2 ] 2- , [O . MCl 2 ] 2- and O 2- anions. The alkaline-earth metal metsilicate solutions are non-ideal binary mixtures and the liquid phases probably contain mainly Si 3 O 9 6- anions: the orthosilicate solutions probably contain [SiO 4 . MCl 2 ] 4- and SiO 4 4- anions. The alkaline-earth metal titanate solutions are ideal binary mixtures upto titanate mole fraction 0.3-0.6 and the liquid phases probably contain only TiO 3 2- anions. The overall ionic equilibria, occurring in the liquid phases during the chemical reactions of silica (and titania) with alkaline-earth metal oxides in metal chloride melts in this temperature range, were thence assessed. (author)

  9. Heavy metal content in edible salts in Isfahan and estimation of their daily intake via salt consumption

    Directory of Open Access Journals (Sweden)

    Hajar Pourgheysari

    2012-01-01

    Conclusions: There was a significant difference between the heavy metal concentrations and their guideline values. Estimation of the health risk due to heavy metals was not possible as PTWI showed total intake of a metal by total food consumption during a week. Therefore, it was important to assess the public health risks arising from the presence of these toxic contaminants in the foods consumed by the population of Iran.

  10. Use of polysulfides of alkali and alkaline-earth metals to obtain highly dispersed sulfur

    International Nuclear Information System (INIS)

    Massalimov, I.A.; Vikhareva, I.N.; Kireeva, M.S.

    2008-01-01

    Possibilities of obtaining polysulfides of alkali and alkaline earth metals (M is Na, K, Ca, Sr, Ba) in aqueous solutions were considered. The composition of the polysulfides and their concentration in solutions were found. The efficiencies of application of highly dispersed sulfur, produced from calcium polysulfide, and colloid sulfur as a fungicide were compared [ru

  11. Study of solubility of akaline earth metals in liquid iron and in alloys on its base

    International Nuclear Information System (INIS)

    Ageev, Yu.A.; Archugov, S.A.

    1985-01-01

    Solubility of magnesium, calcium, strontium and barium in liquid iron and its alloys with aluminium, silicon, nickel, chromium and carbon at 1600 deg C has been measured. Interaction parameters taking account of the effect of added elements on alkaline earth metal solubility in liquid iron have been estimated

  12. Molecular dynamics of liquid alkaline-earth metals near the melting ...

    Indian Academy of Sciences (India)

    Results of the studies of the properties like binding energy, the pair distribution function (), the structure factor (), specific heat at constant volume, velocity autocorrelation function (VACF), radial distribution function, self-diffusion coefficient and coordination number of alkaline-earth metals (Be, Mg, Ca, Sr and Ba) near ...

  13. Composite nanoparticles containing rare earth metal and methods of preparation thereof

    Energy Technology Data Exchange (ETDEWEB)

    Kandapallil, Binil Itty Ipe; Krishnan, Lakshmi; Johnson, Francis

    2018-04-10

    The present invention is directed to composite nanoparticles comprising a metal, a rare earth element, and, optionally, a complexing ligand. The invention is also directed to composite nanoparticles having a core-shell structure and to processes for preparation of composite nanoparticles of the invention.

  14. Doping of graphite by an alkaline-earth metal to reduce the work function

    NARCIS (Netherlands)

    Baturin, AS; Nikolski, KN; Knyazev, AI; Tchesov, RG; Sheshin, EP

    2004-01-01

    A technique for reducing the work function of a field-emission graphite cathode by doping it by an alkaline-earth metal (barium) is suggested. A model of formation of a barium monolayer on the cathode surface is proposed. Field-emission tests show that the operating voltage of the doped cathode is

  15. Effect of Rare Earth Metals on the Microstructure of Al-Si Based Alloys

    Directory of Open Access Journals (Sweden)

    Saleh A. Alkahtani

    2016-01-01

    Full Text Available The present study was performed on A356 alloy [Al-7 wt %Si 0.0.35 wt %Mg]. To that La and Ce were added individually or combined up to 1.5 wt % each. The results show that these rare earth elements affect only the alloy melting temperature with no marked change in the temperature of Al-Si eutectic precipitation. Additionally, rare earth metals have no modification effect up to 1.5 wt %. In addition, La and Ce tend to react with Sr leading to modification degradation. In order to achieve noticeable modification of eutectic Si particles, the concentration of rare earth metals should exceed 1.5 wt %, which simultaneously results in the precipitation of a fairly large volume fraction of insoluble intermetallics. The precipitation of these complex intermetallics is expected to have a negative effect on the alloy performance.

  16. Molten salt extraction (MSE) of americium from plutonium metal in CaCl2-KCl-PuCl3 and CaCl2-PuCl3 salt systems

    International Nuclear Information System (INIS)

    Dodson, K.E.

    1992-01-01

    Molten salt extraction (MSE) of americium-241 from reactor-grade plutonium has been developed using plutonium trichloride salt in stationary furnaces. Batch runs with oxidized and oxide-free metal have been conducted at temperature ranges between 750 and 945C, and plutonium trichloride concentrations from one to one hundred mole percent. Salt-to-metal ratios of 0.10, 0.15, and 0 30 were examined. The solvent salt was either eutectic 74 mole percent CaCl 2 endash 26 mole percent KCl or pure CaCl 2 . Evidence of trivalent product americium, and effects of temperature, salt-to-metal ratio, and oxide contamination on the americium extraction efficiency are given. 24 refs, 20 figs, 13 tabs

  17. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system

    International Nuclear Information System (INIS)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

    2013-01-01

    Highlights: • Recycling of rare earth metals from fluorescent lamps was conducted by ionic liquid-mediated extraction. • Acid leaching from a waste phosphor powder was carried out using sulfuric and nitric acids. • An ionic liquid was used as extracting solvent for the rare earth metals. • Selective extraction of rare earth metals from leach solutions was attained. •The extracting ionic liquid phase was recyclable in the recovery process. -- Abstract: The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid–liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system

  18. The alkali and alkaline earth metal doped ZnO nanotubes: DFT studies

    International Nuclear Information System (INIS)

    Peyghan, Ali Ahmadi; Noei, Maziar

    2014-01-01

    Doping of several alkali and alkaline earth metals into sidewall of an armchair ZnO nanotube has been investigated by employing the density functional theory in terms of energetic, geometric, and electronic properties. It has been found that doping processes of the alkali and alkaline metals are endothermic and exothermic, respectively. Based on the results, contrary to the alkaline metal doping, the electronic properties of the tube are much more sensitive to alkali metal doping so that it is transformed from intrinsic semiconductor with HOMO–LUMO energy gap of 3.77 eV to an extrinsic semiconductor with the energy gap of ∼1.11–1.95 eV. The doping of alkali and alkaline metals increases and decreases the work function of the tube, respectively, which may influence the electron emission from the tube surface

  19. Reoxidation of uranium metal immersed in a Li2O-LiCl molten salt after electrolytic reduction of uranium oxide

    Science.gov (United States)

    Choi, Eun-Young; Jeon, Min Ku; Lee, Jeong; Kim, Sung-Wook; Lee, Sang Kwon; Lee, Sung-Jai; Heo, Dong Hyun; Kang, Hyun Woo; Jeon, Sang-Chae; Hur, Jin-Mok

    2017-03-01

    We present our findings that uranium (U) metal prepared by using the electrolytic reduction process for U oxide (UO2) in a Li2O-LiCl salt can be reoxidized into UO2 through the reaction between the U metal and Li2O in LiCl. Two salt types were used for immersion of the U metal: one was the salt used for electrolytic reduction, and the other was applied to the unused LiCl salts with various concentrations of Li2O and Li metal. Our results revealed that the degree of reoxidation increases with the increasing Li2O concentration in LiCl and that the presence of the Li metal in LiCl suppresses the reoxidation of the U metal.

  20. Time dependent enhanced resistance against antibiotics & metal salts by planktonic & biofilm form of Acinetobacter haemolyticus MMC 8 clinical isolate.

    Science.gov (United States)

    Gaidhani, Sharvari Vijaykumar; Raskar, Aartee Vishnu; Poddar, Sharmishtha; Gosavi, Shriya; Sahu, Praveen Kishore; Pardesi, Karishma Rajendra; Bhide, Shobhana V; Chopade, Balu Ananada

    2014-11-01

    Available literature shows paucity of reports describing antibiotic and metal resistance profile of biofilm forming clinical isolates of Acinetobacter haemolyticus. The present study was undertaken to evaluate the antibiotic and metal resistance profile of Indian clinical isolate of A. haemolyticus MMC 8 isolated from human pus sample in planktonic and biofilm form. Antibiotic susceptibility and minimum inhibitory concentration were determined employing broth and agar dilution techniques. Biofilm formation was evaluated quantitatively by microtiter plate method and variation in complex architecture was determined by scanning electron microscopy. Minimum biofilm inhibiting concentration was checked by Calgary biofilm device. Planktonic A. haemolyticus MMC 8 was sensitive to 14 antibiotics, AgNO 3 and HgC1 2 resistant to streptomycin and intermediately resistant to netilmycin and kanamycin. MMC 8 exhibited temporal variation in amount and structure of biofilm. There was 32-4000 and 4-256 fold increase in antibiotic and metal salt concentration, respectively to inhibit biofilm over a period of 72 h as against susceptible planktonic counterparts. Total viable count in the range of 10(5)-10(6) cfu / ml was observed on plating minimum biofilm inhibiting concentration on Muller-Hinton Agar plate without antimicrobial agents. Biofilm forming cells were several folds more resistant to antibiotics and metal salts in comparison to planktonic cells. Presence of unaffected residual cell population indicated presence of persister cells. The results indicate that biofilm formation causes enhanced resistance against antibiotics and metal salts in otherwise susceptible planktonic A. haemolyticus MMC 8.

  1. How can we take advantage of halophyte properties to cope with heavy metal toxicity in salt-affected areas?

    Science.gov (United States)

    Lutts, Stanley; Lefèvre, Isabelle

    2015-01-01

    Background Many areas throughout the world are simultaneously contaminated by high concentrations of soluble salts and by high concentrations of heavy metals that constitute a serious threat to human health. The use of plants to extract or stabilize pollutants is an interesting alternative to classical expensive decontamination procedures. However, suitable plant species still need to be identified for reclamation of substrates presenting a high electrical conductivity. Scope Halophytic plant species are able to cope with several abiotic constraints occurring simultaneously in their natural environment. This review considers their putative interest for remediation of polluted soil in relation to their ability to sequester absorbed toxic ions in trichomes or vacuoles, to perform efficient osmotic adjustment and to limit the deleterious impact of oxidative stress. These physiological adaptations are considered in relation to the impact of salt on heavy metal bioavailabilty in two types of ecosystem: (1) salt marshes and mangroves, and (2) mine tailings in semi-arid areas. Conclusions Numerous halophytes exhibit a high level of heavy metal accumulation and external NaCl may directly influence heavy metal speciation and absorption rate. Maintenance of biomass production and plant water status makes some halophytes promising candidates for further management of heavy-metal-polluted areas in both saline and non-saline environments. PMID:25672360

  2. Electronic and Magnetic Properties of Rare-Earth Metals Doped ZnO Monolayer

    Directory of Open Access Journals (Sweden)

    Changlong Tan

    2015-01-01

    Full Text Available The structural, electronic, and magnetic properties of rare-earth metals doped ZnO monolayer have been investigated using the first-principles calculations. The induced spin polarization is confirmed for Ce, Eu, Gd, and Dy dopings while the induced spin polarization is negligible for Y doping. The localized f states of rare-earth atoms respond to the introduction of a magnetic moment. ZnO monolayer undergoes transition from semiconductor to metal in the presence of Y, Ce, Gd, and Dy doping. More interestingly, Eu doped ZnO monolayer exhibits half-metallic behavior. Our result demonstrates that the RE-doping is an efficient route to modify the magnetic and electronic properties in ZnO monolayer.

  3. 1H NMR spectroscopic analysis detects metabolic disturbances in rat urine on acute exposure to heavy metal tungsten alloy based metals salt.

    Science.gov (United States)

    Tyagi, Ritu; Rana, Poonam; Gupta, Mamta; Bhatnagar, Deepak; Srivastava, Shatakshi; Roy, Raja; Khushu, Subash

    2014-03-25

    Heavy metal tungsten alloys (HMTAs) have been found to be safer alternatives for making military munitions. Recently, some studies demonstrating the toxic potential of HMTAs have raised concern over the safety issues, and further propose that HMTAs exposure may lead to physiological disturbances as well. To look for the systemic effect of acute toxicity of HMTA based metals salt, (1)H nuclear magnetic resonance ((1)H NMR) spectroscopic profiling of rat urine was carried out. Male Sprague Dawley rats were administered (intraperitoneal) low and high dose of mixture of HMTA based metals salt and NMR spectroscopy was carried out in urine samples collected at 8, 24, 72 and 120 h post dosing (p.d.). Serum biochemical parameters and liver histopathology were also conducted. The (1)H NMR spectra were analysed using multivariate analysis techniques to show the time- and dose-dependent biochemical variations in post HMTA based metals salt exposure. Urine metabolomic analysis showed changes associated with energy metabolism, amino acids, N-methyl nicotinamide, membrane and gut flora metabolites. Multivariate analysis showed maximum variation with best classification of control and treated groups at 24h p.d. At the end of the study, for the low dose group most of the changes at metabolite level reverted to control except for the energy metabolites; whereas, in the high dose group some of the changes still persisted. The observations were well correlated with histopathological and serum biochemical parameters. Further, metabolic pathway analysis clarified that amongst all the metabolic pathways analysed, tricarboxylic acid cycle was most affected at all the time points indicating a switchover in energy metabolism from aerobic to anaerobic. These results suggest that exposure of rats to acute doses of HMTA based metals salt disrupts physiological metabolism with moderate injury to the liver, which might indirectly result from heavy metals induced oxidative stress. Copyright

  4. Oxidation by hydrogen in the chemistry and physics of the rare-earth metals.

    Science.gov (United States)

    Simon, Arndt

    2012-04-27

    Rare-earth metals (RE) easily react with hydrogen. For decades the bonding of hydrogen has been discussed controversially in terms of either the "proton model" or the "anion model". Detailed investigations of metal-rich compounds of the rare-earth metals provide clear evidence for the incorporation of hydrogen as a hydride anion. Several categories of compounds can be distinguished regarding their behavior towards hydrogen. Low-valence compounds with metal-metal bonding frequently provide their excess electrons to form hydride ions as found with the halide hydrides REXH(n). However, there are exceptions, such as, LaI which does not react with hydrogen as a result of special electronic and electrostatic conditions. The opposite is true with La(2)C(3) although this compound does not provide excess metal valence electrons. An amorphous phase La(2)C(3)H(1.5) forms at very low temperature, around 450 K. The presence of hydrogen strongly influences the electrical and magnetic properties, for example, spin-glass formation and colossal magneto resistance arising in the presence of 4f(n) cores with the lanthanoid elements. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Selective extraction and recovery of rare earth metals from phosphor powders in waste fluorescent lamps using an ionic liquid system.

    Science.gov (United States)

    Yang, Fan; Kubota, Fukiko; Baba, Yuzo; Kamiya, Noriho; Goto, Masahiro

    2013-06-15

    The recycling of rare earth metals from phosphor powders in waste fluorescent lamps by solvent extraction using ionic liquids was studied. Acid leaching of rare earth metals from the waste phosphor powder was examined first. Yttrium (Y) and europium (Eu) dissolved readily in the acid solution; however, the leaching of other rare earth metals required substantial energy input. Ionization of target rare earth metals from the waste phosphor powders into the leach solution was critical for their successful recovery. As a high temperature was required for the complete leaching of all rare earth metals, ionic liquids, for which vapor pressure is negligible, were used as an alternative extracting phase to the conventional organic diluent. An extractant, N, N-dioctyldiglycol amic acid (DODGAA), which was recently developed, showed a high affinity for rare earth metal ions in liquid-liquid extraction although a conventional commercial phosphonic extractant did not. An effective recovery of the rare earth metals, Y, Eu, La and Ce, from the metal impurities, Fe, Al and Zn, was achieved from the acidic leach solution of phosphor powders using an ionic liquid containing DODGAA as novel extractant system. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. Computer simulation studies of ternary uranate phases with alkali and alkaline-earth metals: Pt. 1

    International Nuclear Information System (INIS)

    Ball, R.G.J.

    1992-01-01

    Solid-state computer simulation techniques have been used to study the alkali and alkaline-earth metal MUO 3 uranate phases. These compounds display an interesting gradation in their structures which, it is shown, is accompanied by a variation in their intrinsic defect chemistry. For example, in the alkali-metal series, LiUO 3 adopts the lithium niobate structure and lithium Frenkel disorder dominates whereas KUO 3 and RbUO 3 adopt regular perovskite structures with Schottky defects being dominant. For the alkaline-earth metal compounds, both the calculations and experiment show that only SrUO 3 and BaUO 3 are stable with respect to the binary oxides. Both of these phases adopt the GdFeO 3 distorted perovskite structure and both have anti-site defects as the dominant intrinsic disorder. The tendency for anti-site disorder is also seen in the oxidation behaviour of these compounds. The calculations suggest that the oxidation will occur through the formation of a secondary UO 2 fluorite phase by the movement of alkaline-earth ions onto uranium sites, leaving behind M vacancies. The calculated energies for such oxidation processes are particularly favourable. The solution of alkaline-earth oxide, M 11 O, in M 11 UO 3 is shown to occur via a mechanism in which the M 11 ions substitute onto both the M 11 and U sublattices. (author)

  7. Alkaline-earth metal bicarbonates as lixiviants for uranium (VI) under CO2 sparging

    International Nuclear Information System (INIS)

    Vaziri, F.; White, D.A.

    1989-01-01

    In recent years it has become apparent that uranium is significantly soluble in solutions of alkaline-earth metal bicarbonates -particularly those of magnesium and calcium. A system has been proposed by previous authors in which milled uranium ore is leached in a medium to which an oxidizing agent, the metal hydroxide and CO 2 are added. The alkaline-earth metal hydroxides are much more readily soluble in this medium than the corresponding carbonates. Magnesium and calcium bicarbonates are quite soluble in aqueous media at neutral or nearly neutral pH. The pH determines the relative quantities of bicarbonate and carbonate ions in the system. Even if the pH is quite low, small amounts of carbonate ion are present that can complex with the uranyl ion to produce anionic uranyl complexes. Both UO 2 (CO 3 ) 2 2- and UO 2 (CO 3 ) 3 4- complexes are known and both have a very high stability constant. Despite the appearance of several patents on the use of alkaline-earth metal ions in carbonate media as uranium lixiviants, little theoretical or experimental work on the system has been published. In view of the potential of these systems for cheap, large-scale dissolution of uranium the present contribution will discuss the theory behind this method and provide some experimental data to verify the theoretical treatment. (author)

  8. Thermochemistry of the alkali metal and alkaline earth-actinide complex oxides

    International Nuclear Information System (INIS)

    Fuger, J.

    1985-01-01

    After a brief discussion of the various techniques used for the preparation of actinide complex oxides, the present status of the thermochemistry of these compounds is reviewed. Perovskite-related compounds are especially considered as thermodynamic data are available for compounds of several actinides and/or several alkali and alkaline earth metals. The stabilities of the complex oxides are discussed with respect to the parent binary oxides and to the aqueous ions; trends as a function of the size and the alkali or the alkaline earth cation are presented. Suggestions for synthesis of some analogous compounds with heavier actinides are also discussed. (orig./RK)

  9. Recovery of Rare Earth Metals in Used Magnets by Molten Magnesium

    Science.gov (United States)

    Akahori, Tomohiko; Miyamoto, Yu; Saeki, Tomonori; Okamoto, Masahide; Okabe, Toru H.

    We report here Hitachi's approach to recycle rare earth (RE) metals in used magnets by using molten magnesium (Mg). The process consists of 3 steps; (1) extraction of RE metals from magnets into molten Mg, to form Mg-RE melt, (2) mechanical separation of magnets from the Mg-RE melt, (3) collection of RE metals by evaporation of Mg in the Mg-RE melt. In the step 1, extraction of RE metals proceeds rapidly and completes in about 3 h. The efficiency strongly depends on the temperature (T) and Mg/magnet ratio (r)). One of the optimal conditions is T=1273 (K) and η is 10, where the efficiencies for Nd and Dy extraction are almost 100 % and 60 %, respectively. Further increase of Dy extraction efficiency is possible by addition of Ca to suppress the oxidation of Dy.

  10. Prolinate Salt as a Catalyst in the syn-Selective, Asymmetric Mannich Reaction of Alkynyl Imine.

    Science.gov (United States)

    Hayashi, Yujiro; Yamazaki, Tatsuya; Kawauchi, Genki; Sato, Itaru

    2018-04-04

    Prolinate salt is an efficient catalyst in the Mannich reaction of alkynyl imine and aldehyde, to afford synthetically useful chiral propargyl amine derivatives with excellent syn-selectivity and nearly perfect control of the absolute configuration. The counterion of the prolinate salt does not affect the enantioselectivity. This is a rare example, in which proline alkali metals, alkaline-earth metals, or ammonium salt show higher reactivity and better stereoselectivity than the parent proline.

  11. Remote laser-induced breakdown spectroscopy for the detection and removal of salt on metal and polymeric surfaces.

    Science.gov (United States)

    Bengtsson, M; Grönlund, R; Lundqvist, M; Larsson, A; Kröll, S; Svanberg, S

    2006-10-01

    The detection of contamination such as salt in outdoor high-voltage insulator systems and its subsequent removal are vital for a reliable transmission of electric power. Remote detection of salt on a copper metal surface was carried out by using a mobile laser-induced breakdown spectroscopy (LIBS) Lidar system with a laser wavelength of 355 nm. Detection of salt on a polymeric high-voltage insulator was obtained when an additional lens was inserted into the beam path, and the number of photons that was detected could be calculated by using a calibrated white light source. Ablative cleaning could readily be carried out with LIBS and was verified by observing the disappearance of the sodium D-line emission.

  12. Galvanic reduction of uranium(III) chloride from LiCl-KCl eutectic salt using gadolinium metal

    Science.gov (United States)

    Bagri, Prashant; Zhang, Chao; Simpson, Michael F.

    2017-09-01

    The drawdown of actinides is an important unit operation to enable the recycling of electrorefiner salt and minimization of waste. A new method for the drawdown of actinide chlorides from LiCl-KCl molten salt has been demonstrated here. Using the galvanic interaction between the Gd/Gd(III) and U/U(III) redox reactions, it is shown that UCl3 concentration in eutectic LiCl-KCl can be reduced from 8.06 wt.% (1.39 mol %) to 0.72 wt.% (0.12 mol %) in about an hour via plating U metal onto a steel basket. This is a simple process for returning actinides to the electrorefiner and minimizing their loss to the salt waste stream.

  13. Solid oxide membrane-assisted controllable electrolytic fabrication of metal carbides in molten salt.

    Science.gov (United States)

    Zou, Xingli; Zheng, Kai; Lu, Xionggang; Xu, Qian; Zhou, Zhongfu

    2016-08-15

    Silicon carbide (SiC), titanium carbide (TiC), zirconium carbide (ZrC), and tantalum carbide (TaC) have been electrochemically produced directly from their corresponding stoichiometric metal oxides/carbon (MOx/C) precursors by electrodeoxidation in molten calcium chloride (CaCl2). An assembled yttria stabilized zirconia solid oxide membrane (SOM)-based anode was employed to control the electrodeoxidation process. The SOM-assisted controllable electrochemical process was carried out in molten CaCl2 at 1000 °C with a potential of 3.5 to 4.0 V. The reaction mechanism of the electrochemical production process and the characteristics of these produced metal carbides (MCs) were systematically investigated. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses clearly identify that SiC, TiC, ZrC, and TaC carbides can be facilely fabricated. SiC carbide can be controlled to form a homogeneous nanowire structure, while the morphologies of TiC, ZrC, and TaC carbides exhibit porous nodular structures with micro/nanoscale particles. The complex chemical/electrochemical reaction processes including the compounding, electrodeoxidation, dissolution-electrodeposition, and in situ carbonization processes in molten CaCl2 are also discussed. The present results preliminarily demonstrate that the molten salt-based SOM-assisted electrodeoxidation process has the potential to be used for the facile and controllable electrodeoxidation of MOx/C precursors to micro/nanostructured MCs, which can potentially be used for various applications.

  14. Electrodeposition of metallic tungsten coating from binary oxide molten salt on low activation steel substrate

    International Nuclear Information System (INIS)

    Liu, Y.H.; Zhang, Y.C.; Jiang, F.; Fu, B.J.; Sun, N.B.

    2013-01-01

    Tungsten is considered a promising plasma facing armor material for future fusion devices. An electrodeposited metallic tungsten coating from Na 2 WO 4 –WO 3 binary oxide molten salt on low activation steel (LAS) substrate was investigated in this paper. Tungsten coatings were deposited under various pulsed currents conditions at 1173 K in atmosphere. Cathodic current density and pulsed duty cycle were investigated for pulsed current electrolysis. The crystal structure and microstructure of tungsten coatings were characterized by X-ray diffractometry, scanning electron microscopy, and energy X-ray dispersive analysis techniques. The results indicated that pulsed current density and duty cycle significantly influence tungsten nucleation and electro-crystallization phenomena. The average grain size of the coating becomes much larger with increasing cathodic current density, which demonstrates that appropriate high cathodic current density can accelerate the growth of grains on the surface of the substrate. The micro-hardness of tungsten coatings increases with the increasing thickness of coatings; the maximum micro-hardness is 482 HV. The prepared tungsten coatings have a smooth surface, a porosity of less than 1%, and an oxygen content of 0.024 wt%

  15. Metal-insulator transition of alloyed radical cation salts, (MexEDO-TTF)2PF6

    Science.gov (United States)

    Murata, Tsuyoshi; Shao, Xiangfeng; Nakano, Yoshiaki; Yamochi, Hideki; Saito, Gunzi; Uruichi, Mikio; Yakushi, Kyuya; Tanaka, Koichiro

    2010-06-01

    Ternary radical cation salts containing ethylenedioxytetrathiafulvalene, its mono-methyl substituted derivative, and hexafluorophosphate, [(EDO-TTF)1-x(MeEDO-TTF)x]2PF6 (x=mole fraction of MeEDO-TTF, x=0.01-0.13) were prepared by electrooxidation. Mole fractions of EDO-TTF and MeEDO-TTF in EDO-TTF rich alloys were consistent with the donor mixing ratios in preparation. Crystal structures of these alloys at room temperature were isostructural to that of (EDO-TTF)2PF6, where the donor molecules formed a nearly uniform stacking column to give a quasi-one-dimensional Fermi surface. The alloys exhibited a metal-insulator transition with tetramerization within the donor stack and anion-ordering. Temperature-variable structural analysis and Raman spectra revealed that the charge-ordering took place in the low temperature phase of x=0.05 alloy, however, this feature vanished in the x=0.13 alloy. The phase transition temperature decreased with increasing x value from 279 K of pristine (EDO-TTF)2PF6 to 188 K of x=0.13 alloy.

  16. The Influence of Salt Anions on Heavy Metal Ion Adsorption on the Example of Nickel

    Science.gov (United States)

    Mende, Mandy; Schwarz, Dana; Steinbach, Christine; Schwarz, Simona

    2018-01-01

    The biodegradable polysaccharide chitosan possesses protonated and natural amino groups at medium pH values and has therefore been used as an adsorbing material for nickel salts in water treatment. Nickel is a problematic heavy metal ion which can cause various diseases and disorders in living organisms. Here, we show the influence of oxyanions (e.g., nitrate and sulfate) to the adsorption of nickel ions. Hence, simultaneously we are addressing the increasing global problem of nitrate and sulfate ion pollution in groundwater and surface water. A series of adsorption experiments was carried out in order to determine (i) the adsorption equilibrium, (ii) the adsorption capacity in dependence on the initial nickel ion concentration, and (iii) the influence of the anion presented in solution for the adsorption capacity. Surface morphology of chitosan flakes before and after the adsorption process has been studied with SEM-EDX analysis. The chitosan flakes exhibited promising adsorption capacities of 81.9 mg·g−1 and 21.2 mg·g−1 for nickel (sulfate) and nickel (nitrate), respectively. The calculated values of Gibbs free energy change ΔG0 confirm the higher adsorption of nickel ions in presence of sulfate ions. Hence, higher anion valence leads to a higher adsorption capacity. PMID:29510485

  17. Water oxidation using earth-abundant transition metal catalysts: opportunities and challenges.

    Science.gov (United States)

    Kärkäs, Markus D; Åkermark, Björn

    2016-10-07

    Catalysts for the oxidation of H2O are an integral component of solar energy to fuel conversion technologies. Although catalysts based on scarce and precious metals have been recognized as efficient catalysts for H2O oxidation, catalysts composed of inexpensive and earth-abundant element(s) are essential for realizing economically viable energy conversion technologies. This Perspective summarizes recent advances in the field of designing homogeneous water oxidation catalysts (WOCs) based on Mn, Fe, Co and Cu. It reviews the state of the art catalysts, provides insight into their catalytic mechanisms and discusses future challenges in designing bioinspired catalysts based on earth-abundant metals for the oxidation of H2O.

  18. Properties of the triplet metastable states of the alkaline-earth-metal atoms

    International Nuclear Information System (INIS)

    Mitroy, J.; Bromley, M.W.J.

    2004-01-01

    The static and dynamic properties of the alkaline-earth-metal atoms in their metastable state are computed in a configuration interaction approach with a semiempirical model potential for the core. Among the properties determined are the scalar and tensor polarizabilities, the quadrupole moment, some of the oscillator strengths, and the dispersion coefficients of the van der Waals interaction. A simple method for including the effect of the core on the dispersion parameters is described

  19. Formation of an integrated holding company to produce rare-earth metal articles

    Science.gov (United States)

    Bogdanov, S. V.; Grishaev, S. I.

    2013-12-01

    The possibility of formation of a Russian holding company for the production of rare-earth metal articles under conditions of its increasing demand on the world market is considered. It is reasonable to ensure stable business operation on the market under conditions of state-private partnership after the fraction of soled products is determined and supported by the competitive advantages of Russian products.

  20. No Giant Two-Ion Anisotropy in the Heavy-Rare-Earth Metals

    DEFF Research Database (Denmark)

    Lindgård, Per-Anker

    1976-01-01

    A new Bose-operator expansion of tensor operators is applied to the heavy-rare-earth metals. The Er data for the cone phase have been analyzed successfully with single-ion anisotropy and isotropic exchange interaction. The Tb data can be understood on the same basis. The previously found large two......-ion anisotropy was due to an inadequate treatment of the large single-ion anisotropy leading to an incorrect expression for the spin-wave energy....

  1. Optimization of film synthesized rare earth transition metal permanent magnet systems

    International Nuclear Information System (INIS)

    Cadieu, F.J.

    1992-01-01

    Progress is reported in three areas: high coercivity Sm-Fe-Ti-V, Sm-Fe-Zr, and two element Sm-Fe Sm 5 (Fe,T) 17 type crystalline phases; ThMn 12 type pseudobinary SmFe 12-x T x (0≤x≤1.5); and sputter process control for the synthesis of precisely textured rare earth-transition metal magnetic films

  2. Alteration of non-metallic barriers and evolution of solution chemistry in salt formations in Germany

    International Nuclear Information System (INIS)

    Herbert, H.J.; Becker, D.; Hagemann, S.; Meyer, Th.; Noseck, U.; Rubel, A.; Mauke, R.; Wollrath, J.

    2005-01-01

    Different Engineered Barrier Systems (EBS) materials considered in Germany for the sealing of repositories in salt formations are presented. Their long term behaviour in terms of interactions with salt solutions is discussed and evaluated. The discussed EBS materials are crushed salt, self sealing salt backfill, bentonite and salt concrete. Whereas the knowledge concerning the geochemical, geomechanical, hydrological and thermal behavior of crushed salt and salt concrete is well advanced further research is needed for other EBS materials. The self healing salt backfill has also been investigated in depth recently. In order to fully qualify this material large scale in situ experiments are still needed. The present knowledge on compacted bentonites in a salt environment is not yet sufficient for reliable predictions of the long-term performance in salt formations. The sealing concept of the low- and intermediate-level Radioactive Waste Repository Morsleben (ERAM) in a former rock salt and potash mine is presented. This concept is based on cementitious materials, i.e. salt concrete. The geochemical stability of different salt concretes in contact with brines expected in ERAM is addressed. It is shown how the results from leaching experiments and geochemical modelling are used in the safety analyses and how the chemical boundary conditions prevailing in the EBS influence the development of the permeability of the sealing system and thus control the radionuclide release. As a result of modelling the behaviour of the seals in the safety assessment it is shown, that the seals are corroded within a time span of about 20 000 years. The influence of the uncertainty in the model parameters on the safety of the repository was assessed by a variation of the initial permeability of the seal. The maximum dose rate resulting from the radionuclide release from ERAM is nearly independent of the variation of the initial permeability within four orders of magnitude. (authors)

  3. Preparation of polymers suitable for radiation shielding and studying its properties (polyester composites with heavy metals salts)

    International Nuclear Information System (INIS)

    Kharita, M. H.; Al-Ajji, Z.; Yousef, S.

    2010-12-01

    Four composites were prepared in this work, based on polyester and heavy metals oxides and salts. The attenuation properties, as well as mechanical properties were studied, and the chemical stability was evaluated. It has been shown, that these composites can be used in radiation shielding for X-rays successfully, and the exact composition of these composites can be optimized according to the radiation energy to prepare the lightest possible shield. (author)

  4. CPA theory of the magnetization in rare earth transition metal alloys

    International Nuclear Information System (INIS)

    Szpunar, B.; Lindgaard, P.A.

    1976-11-01

    Calculations were made of the magnetic moment per atom of the transition metal and the rare earth metal in the intermetallic compounds, Gdsub(1-x)Nisub(x), Gdsub(1-x)Fesub(x), Gdsub(1-x)Cosub(x), and Ysub(1-x)Cosub(x). A simple model of the disordered alloy consisting of spins localized on the rare earth atoms and interacting with a narrow d-band is considered. The magnetic moment of the alloy at zero temperature is calculated within the molecular field and Hartree-Fock approximations. Disorder is treated in the coherent potential approximation. Results are in good agreement with the experimental data obtained for the crystalline and amorphous intermetallic compounds. It is shown that the temperature dependence of the magnetic moments and Curie and ferrimagnetic compensation temperatures can be accounted for by a simple model assuming a RKKY interaction between the rare-earth moments and the transition metal pseudo spin. The interaction is mediated by an effective alloy medium calculated using the CPA theory and elliptic densities of states. (Auth.)

  5. Monitoring the Electrolytic Reduction Process of Metal Oxide in the LiCl Molten Salt at 650 . deg. C

    International Nuclear Information System (INIS)

    Choi, In kyu; Hong, Soon Seok; Jung, Myoung Soo; Hur, Jin Mok; Lee, Han Soo

    2010-01-01

    During the electrolytic reduction process of metal oxides, metal oxides are reduced in the cathode basket and oxide ions are oxidized at a platinum anode. Basically the oxide concentration in the bulk should be maintained to be constant during the reduction process, but slow diffusion rate of oxide ions from metal oxide particles to the salt medium results in decreasing the oxide ion concentration. When a high current density is applied for the reduction, lowered lithium oxide concentration causes the platinum anode to be dissolved. To accomplish the reduction of metal oxides without serious damage of platinum anode, monitoring the lithium oxide concentration is very important. For in-situ monitoring the oxide concentration during the reduction, cyclic voltammetry (CV) and chronoamperometry(CA) were applied

  6. Isostructural crystal hydrates of rare-earth metal oxalates at high pressure. From strain anisotropy to dehydration

    Energy Technology Data Exchange (ETDEWEB)

    Zakharov, Boris A.; Matvienko, Alexander A. [Russian Academy of Ssciences, Novosibirsk (Russian Federation). Inst. of Solid State Chemistry and Mechanochemistry; Novosibirsk State Univ. (Russian Federation); Gribov, Pavel A.; Boldyreva, Elena V. [Russian Academy of Ssciences, Novosibirsk (Russian Federation). Inst. of Solid State Chemistry and Mechanochemistry

    2017-07-01

    The crystal structures of a series of isostructural rare-earth metal oxalates, (REE){sub 2}(C{sub 2}O{sub 4}){sub 3}.10H{sub 2}O (REE=Sm, Y) and a 1:1 YSm(C{sub 2}O{sub 4}){sub 3}.10H{sub 2}O solid solution, have been studied in situ by single-crystal X-ray diffraction and optical microscopy. The structures were followed from ambient pressure to 6 GPa in a DAC with paraffin as the hydrostatic fluid. Bulk compressibilities, anisotropic lattice strain on hydrostatic compression and the corresponding changes in the atomic coordinates were followed. Discontinuities/sharp changes in the slopes of the pressure dependences of volume and selected cell parameters have been observed for yttrium-containing salts at ∝3.5 GPa. This may be related to the re-distribution of water molecules within the crystal structure. Y{sub 2}(C{sub 2}O{sub 4}){sub 3}.10H{sub 2}O undergoes a partial dehydration at 1 GPa, forming monoclinic Y{sub 2}(C{sub 2}O{sub 4}){sub 3}.6H{sub 2}O as single-crystalline inclusions in the original phase.

  7. Semiempirical calculation of van der Waals coefficients for alkali-metal and alkaline-earth-metal atoms

    International Nuclear Information System (INIS)

    Mitroy, J.; Bromley, M.W.J.

    2003-01-01

    The van der Waals coefficients, C 6 , C 8 , and C 10 for the alkali-metal (Li, Na, K, and Rb) and alkaline-earth-metal (Be, Mg, Ca, and Sr) atoms are estimated by a combination of ab initio and semiempirical methods. Polarizabilities and atom-wall coefficients are given as a diagnostic check, and the lowest order nonadiabatic dispersion coefficient, D 8 and the three-body coefficient, C 9 are also presented. The dispersion coefficients are in agreement with the available relativistic many-body perturbation theory calculations. The contribution from the core was included by using constrained sum rules involving the core polarizability and Hartree-Fock expectation values to estimate the f-value distribution

  8. Correction: A binary catalyst system of a cationic Ru-CNC pincer complex with an alkali metal salt for selective hydroboration of carbon dioxide.

    Science.gov (United States)

    Ng, Chee Koon; Wu, Jie; Hor, T S Andy; Luo, He-Kuan

    2016-12-22

    Correction for 'A binary catalyst system of a cationic Ru-CNC pincer complex with an alkali metal salt for selective hydroboration of carbon dioxide' by Chee Koon Ng et al., Chem. Commun., 2016, 52, 11842-11845.

  9. TRANSGENIC PLANTS OF RAPE (BRASSICA NAPUS L. WITH GENE OSMYB4 HAVE INCREASED RESISTANCE TO SALTS OF HEAVY METALS

    Directory of Open Access Journals (Sweden)

    Raldugina G.N.

    2012-08-01

    Full Text Available This work aims to study the response of the transgenic spring rape plants (Brassica napus L. var. ‘Westar’ with the rice transfactor-encoding gene Osmyb4 to treatment with salts of heavy metals (HM CuSO4 or ZnSO4 and accumulation in the leaves of biomass, metals, photosynthetic pigments, lipid peroxidation, and antioxidant compounds: total phenols, anthocyanins, and antioxidant enzyme activity superoxide dismutase (SOD and guaiacol peroxidase (POX were determined. Vegetatively propagated transgenic plants and wild-type plants were grown on Hoagland-Snyder medium at 24°C, then at the 5-6th leaves-stage, CuSO4 (in concentration 25-150 mM or ZnSO4 (500 - 5000 mM were added to the growth medium, and plants were exposed to the salts for 15 days. Under the action of small concentrations of salts, the results obtained for the transgenic and untransformed plants did not differ, but at high concentrations strong differences between transgenic and untransformed plants were observed. In transgenic plants, accumulation of biomass was greater. Carotene and xanthophyll were destroyed in transgenic plants less than in the untransformed plants. They have accumulated in their leaves more metal, especially Zn, reaching almost to the accumulation of 7 mg per g of dry biomass, bringing these plants to the hyperaccumulation of Zn. In the tissues of transgenic plants exposed to high concentrations of salts, the content of total phenols, anthocyanins, and low molecular weight compounds, that are responsible for protection against ROS, increased significantly. All these results indicate a greater stability of the transgenic plants to the action of heavy metals, as evidenced also by less activity of lipid peroxidases in their tissue: at high salt concentrations, malondialdehyde (MDA accumulated significantly less in transgenic plants than in non-transformed plant tissues. The greater stability of transgenic plants to stressful effect of HM is also evidenced by the

  10. Metal-silicate Partitioning and Its Role in Core Formation and Composition on Super-Earths

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, Laura; Petaev, M. I.; Sasselov, Dimitar D. [Harvard-Smithsonian Center for Astrophysics, 60 Garden St., Cambridge, MA 02138 (United States); Jacobsen, Stein B.; Remo, John L., E-mail: lschaefer@asu.edu [Harvard University, Department of Earth and Planetary Sciences, 20 Oxford St., Cambridge, MA 02138 (United States)

    2017-02-01

    We use a thermodynamic framework for silicate-metal partitioning to determine the possible compositions of metallic cores on super-Earths. We compare results using literature values of the partition coefficients of Si and Ni, as well as new partition coefficients calculated using results from laser shock-induced melting of powdered metal-dunite targets at pressures up to 276 GPa, which approaches those found within the deep mantles of super-Earths. We find that larger planets may have little to no light elements in their cores because the Si partition coefficient decreases at high pressures. The planet mass at which this occurs will depend on the metal-silicate equilibration depth. We also extrapolate the equations of state (EOS) of FeO and FeSi alloys to high pressures, and present mass–radius diagrams using self-consistent planet compositions assuming equilibrated mantles and cores. We confirm the results of previous studies that the distribution of elements between mantle and core will not be detectable from mass and radius measurements alone. While observations may be insensitive to interior structure, further modeling is sensitive to compositionally dependent properties, such as mantle viscosity and core freeze-out properties. We therefore emphasize the need for additional high pressure measurements of partitioning as well as EOSs, and highlight the utility of the Sandia Z-facilities for this type of work.

  11. Interactions of nucleobases with alkali earth metal cations--electrospray ionization mass spectrometric study.

    Science.gov (United States)

    Frańska, Magdalena

    2007-01-01

    Interactions of nucleobases with alkali earth metal cations have been studied by electrospray ionization mass spectrometry (ESI-MS). Nucleobases containing at least one oxygen atom form stable complexes with alkali earth metal cations. This phenomenon can be explained on the grounds of the well known theory of hard and soft acids and bases. Uracil and thymine make complexes only when in their deprotonoted forms. The cations of great radii (Sr(2+), Ba(2+)) are more prone to form complexes of stoichiometry 1:1 with uracil and thymine than the cations of small radii (Mg(2+), Ca(2+)). On the other hand, Mg(2+) forms complexes of stoichiometry 2:1 and 3:2 with uracil and thymine. Gas-phase stabilities of the 1:1 complexes are higher for the cations of small radii, in contrast to the solution stabilities. For cytosine and 9- methylhypoxantine the 1:1 complexes of their deprotonated forms are observed at higher cone voltage as a result of HCl molecule loss from the complexes containing the counter ion (Cl(-)). In solution, more stable complexes are formed with metal cations of low radii. Gas-phase stability of the complexes formed by deprotonated 9- methyl-hypoxantine increases with increasing metal cation radius.

  12. Rare earth elements and critical metal content of extracted landfilled material and potential recovery opportunities.

    Science.gov (United States)

    Gutiérrez-Gutiérrez, Silvia C; Coulon, Frédéric; Jiang, Ying; Wagland, Stuart

    2015-08-01

    Rare earth elements (REEs), Platinum group metals (PGMs) and other critical metals currently attract significant interest due to the high risks of supply shortage and substantial impact on the economy. Their uses in many applications have made them present in municipal solid waste (MSW) and in commercial and industrial waste (C&I), since several industrial processes produce by-products with high content of these metals. With over 4000 landfills in the UK alone, the aim of this study was to assess the existence of these critical metals within landfills. Samples collected from four closed landfills in UK were subjected to a two-step acid digestion to extract 27 metals of interest. Concentrations across the four landfill sites were 58±6mgkg(-1) for REEs comprising 44±8mgkg(-1) for light REEs, 11±2mgkg(-1) for heavy REEs and 3±1mgkg(-1) for Scandium (Sc) and 3±1.0mgkg(-1) of PGMs. Compared to the typical concentration in ores, these concentrations are too low to achieve a commercially viable extraction. However, content of other highly valuable metals (Al and Cu) was found in concentrations equating to a combined value across the four landfills of around $400 million, which increases the economic viability of landfill mining. Presence of critical metals will mainly depend on the type of waste that was buried but the recovery of these metals through landfill mining is possible and is economically feasible only if additional materials (plastics, paper, metallic items and other) are also recovered for reprocessing. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Metal and acidity fluxes controlled by precipitation/dissolution cycles of sulfate salts in an anthropogenic mine aquifer.

    Science.gov (United States)

    Cánovas, C R; Macías, F; Pérez-López, R

    2016-05-01

    Underground mine drainages are extremely difficult to study due to the lack of information about the flow path and source proximity in relation to the outflow adit. Geochemical processes controlling metals and acidity fluxes in a complex anthropogenic mine aquifer in SW Spain during the dry and rainy season were investigated by geochemical and statistical tools. High concentrations of acidity, sulfate, metals and metalloids (e.g. Fe, Cu, Zn, As, Cd, Ni, Co) were observed due to intense sulfide oxidation processes. The high residence time inside the anthropogenic aquifer, around 40days, caused the release of significant quantities of metals linked to host rocks (e.g. Al, Ca, Ge, Li, Mg, REE). The most outstanding characteristic of the acid mine drainage (AMD) outflows is the existence of higher Fe/SO4 molar ratios than those theoretical of pyrite (0.50) during most of the monitored period, due to a fire which occurred in 1949 and remained active for decades. Permanent and temporal retention mechanisms of acidity and metals were observed in the galleries. Once released from sulfide oxidation, Pb and As are sorbed on Fe oxyhydroxysulfate or precipitated as low solubility minerals (i.e. anglesite) inside the galleries. The precipitation of evaporitic sulfate salts during the dry season and the subsequent re-dissolution after rainfall control the fluxes of acidity and main metals (i.e. Fe, Mg, Al) from this anthropogenic aquifer. Some elements, such as Cd, Cu, Ni, REE and Zn, are retained in highly soluble sulfate salts while other elements, such as Ge, Pb and Sc, have a lower response to washout processes due to its incorporation in less soluble sulfate salts. In this way, metal concentration during the washout processes would be controlled by the proportion and solubility of each type of evaporitic sulfate salt stored during the dry season. The recovery of metals of economic interest contained in the AMD could help to self-finance the remediation of these waters in

  14. Heavy metal removal mechanisms of sorptive filter materials for road runoff treatment and remobilization under de-icing salt applications.

    Science.gov (United States)

    Huber, Maximilian; Hilbig, Harald; Badenberg, Sophia C; Fassnacht, Julius; Drewes, Jörg E; Helmreich, Brigitte

    2016-10-01

    The objective of this research study was to elucidate the removal and remobilization behaviors of five heavy metals (i.e., Cd, Cu, Ni, Pb, and Zn) that had been fixed onto sorptive filter materials used in decentralized stormwater treatment systems receiving traffic area runoff. Six filter materials (i.e., granular activated carbon, a mixture of granular activated alumina and porous concrete, granular activated lignite, half-burnt dolomite, and two granular ferric hydroxides) were evaluated in column experiments. First, a simultaneous preloading with the heavy metals was performed for each filter material. Subsequently, the remobilization effect was tested by three de-icing salt experiments in duplicate using pure NaCl, a mixture of NaCl and CaCl2, and a mixture of NaCl and MgCl2. Three layers of each column were separated to specify the attenuation of heavy metals as a function of depth. Cu and Pb were retained best by most of the selected filter materials, and Cu was often released the least of all metals by the three de-icing salts. The mixture of NaCl and CaCl2 resulted in a stronger effect upon remobilization than the other two de-icing salts. For the material with the highest retention, the effect of the preloading level upon remobilization was measured. The removal mechanisms of all filter materials were determined by advanced laboratory methods. For example, the different intrusions of heavy metals into the particles were determined. Findings of this study can result in improved filter materials used in decentralized stormwater treatment systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Laboratory calibration and field testing of the Chemcatcher-Metal for trace levels of rare earth elements in estuarine waters.

    Science.gov (United States)

    Petersen, Jördis; Pröfrock, Daniel; Paschke, Albrecht; Broekaert, Jose A C; Prange, Andreas

    2015-10-01

    Little knowledge is available about water concentrations of rare earth elements (REEs) in the marine environment. The direct measurement of REEs in coastal waters is a challenging task due to their ultra-low concentrations as well as the high salt content in the water samples. To quantify these elements at environmental concentrations (pg L(-1) to low ng L(-1)) in coastal waters, current analytical techniques are generally expensive and time consuming, and require complex chemical preconcentration procedures. Therefore, an integrative passive sampler was tested as a more economic alternative sampling approach for REE analysis. We used a Chemcatcher-Metal passive sampler consisting of a 3M Empore Chelating Disk as the receiving phase, as well as a cellulose acetate membrane as the diffusion-limiting layer. The effect of water turbulence and temperature on the uptake rates of REEs was analyzed during 14-day calibration experiments by a flow-through exposure tank system. The sampling rates were in the range of 0.42 mL h(-1) (13 °C; 0.25 m s(-1)) to 4.01 mL h(-1) (13 °C; 1 m s(-1)). Similar results were obtained for the different REEs under investigation. The water turbulence was the most important influence on uptake. The uptake rates were appropriate to ascertain time-weighted average concentrations of REEs during a field experiment in the Elbe Estuary near Cuxhaven Harbor (exposure time 4 weeks). REE concentrations were determined to be in the range 0.2 to 13.8 ng L(-1), where the highest concentrations were found for neodymium and samarium. In comparison, most of the spot samples measured along the Chemcatcher samples had REE concentrations below the limit of detection, in particular due to necessary dilution to minimize the analytical problems that arise with the high salt content in marine water samples. This study was among the first efforts to measure REE levels in the field using a passive sampling approach. Our results suggest that passive samplers could be

  16. Modification of Non-Metallic Inclusions by Rare-Earth Elements in Microalloyed Steels

    Directory of Open Access Journals (Sweden)

    M. Opiela

    2012-04-01

    Full Text Available The modification of the chemical composition of non-metallic inclusions by rare-earth elements in the new-developed microalloyed steels was discussed in the paper. The investigated steels are assigned to production of forged elements by thermo- mechanical treatment. The steels were melted in a vaccum induction furnace and modification of non-metallic inclusions was carried out by the michmetal in the amount of 2.0 g per 1 kg of steel. It was found that using material charge of high purity and a realization of metallurgical process in vacuous conditions result in a low concentration of sulfur (0.004%, phosphorus (from 0.006 to 0.008% and oxygen (6 ppm. The high metallurgical purity is confirmed by a small fraction of non-metallic inclusions averaging 0.075%. A large majority of non-metallic inclusions are fine, globular oxide-sulfide or sulfide particles with a mean size 17m2. The chemical composition and morphology of non-metallic inclusions was modified by Ce, La and Nd, what results a small deformability of non- metallic inclusions during hot-working.

  17. How Does Boiling in the Earth's Crust Influence Metal Speciation and Transport?

    Science.gov (United States)

    Kam, K.; Lemke, K.

    2014-12-01

    The presence of large quantities of precious metals, such as gold and copper, near the Earth's surface (upper crust) is commonly attributed to transport in aqueous solution and precipitation upon variations in temperature and pressure. As a consequence, gold exploration is closely linked to solution chemistry, i.e. hydrothermal processes involving aqueous fluids with densities of around unity. However, as crustal fluids buoyantly ascend, boiling produces a coexisting low-density aqueous liquid with fundamentally different physical and chemical properties, and a, most importantly, a high affinity for coinage metals (Heinrich et al., Econ Geol., 1992, 87, 1566). From recent experimental studies of Au (Hurtig and Williams-Jones, 2014, Geochim. Cosmochim. Acta,, 127, 304), we know that metal speciation in this low-density phase differs fundamentally from that observed in bulk solution, clearly, with important implications for Au, and metal speciation in general, transport and ore concentrations processes (these processes would also be operable in industrial geothermal plants given the quite special solvent properties of steam). In brief, this study focuses on the speciation of select metal halides in bulk solution as well as in water vapor, and is driven by our need to understand the solvent properties of around 2.0x109 cubic kilometers of free water (or 2,500 times as much water as stored in all lakes and rivers) present in the Earth's crust. The scope of this study has particular applications in the geothermal and oil industries, as both deal with high temperature low-density aqueous fluids. Understanding how metal halide species behave upon boiling can also provide insight into how metals, such as copper and silver, coat turbine equipment and steam piping in geothermal plants, ultimately rendering these components inoperable. This study will also provide preliminary results from mass spectrometric experiments of transition metal halides, and will be augmented with

  18. Effects of alkaline earth metal ion complexation on amino acid zwitterion stability: Results from infrared action spectroscopy

    NARCIS (Netherlands)

    Bush, M. F.; Oomens, J.; Saykally, R. J.; Williams, E. R.

    2008-01-01

    The structures of isolated alkaline earth metal cationized amino acids are investigated using infrared multiple photon dissociation (IRMPD) spectroscopy and theory. These results indicate that arginine, glutamine, proline, serine, and valine all adopt zwitterionic structures when complexed with

  19. Alkali or alkaline earth metal promoted catalyst and a process for methanol synthesis using alkali or alkaline earth metals as promoters

    Science.gov (United States)

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1995-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a heterogeneous catalyst comprising reduced copper chromite impregnated with an alkali or alkaline earth metal. There is thus no need to add a separate alkali or alkaline earth compound. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  20. Synergistic interaction of gamma rays and some metallic salts in the induction of chlorophyll mutations in rice

    International Nuclear Information System (INIS)

    Reddy, T.P.; Vaidyanath, K.

    1978-01-01

    In this study the mutagenic activity of 9 metallic salts was tested in comparison and conjunction with gamma rays on rice seed. In M 2 , barium and cadmium produced chlorophyll mutation and mutant frequencies on a par with those of 20 kR gamma rays. Similarly, copper and mercury induced moderately high mutation and mutant frequencies. Salts of strontium, iron and lead showed rather weak mutagenic effects. On the other hand, two metals - manganese anc calcium - failed to provoke chlorophyll mutations in rice seed. Sequential treatments of gamma rays + 5 metals, namely Sr, Cd, Hg, Pb and Cu, produced synergistic yields of chlorophyll mutants in the M 2 generation. Two genetically active metals, Ba and Fe, showed less than additive effects when post-treated after gamma irradiation. Manganese, which failed to induce chlorophyll mutations in independent treatment, potentiated the mutagenic activity of gamma radiation in sequential treatment. On the other hand, sequential treatment with calcium seemed to confer a substantial protection against gamma-ray-induced genetic lesions. The probable mechanisms of synergistic interaction, mutagenic potentiation and protection, observed in sequential treatments, are discussed. (Auth.)

  1. Rare-earth transition-metal intermetallics: Structure-bonding-property relationships

    Energy Technology Data Exchange (ETDEWEB)

    Han, M. K. [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    The explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding property relationships. The work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe13-xSix system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn{sub 13}-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides Re2-xFe4Si14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi2: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb3Zn3.6Al7.4: Partially ordered structure of Tb3Zn3.6Al7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn39(CrxAl1-x)81

  2. Rare-Earth Transition-Metal Intermetallics: Structure-bonding-Property Relationships

    Energy Technology Data Exchange (ETDEWEB)

    Han, Mi-Kyung [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    Our explorations of rare-earth, transition metal intermetallics have resulted in the synthesis and characterization, and electronic structure investigation, as well as understanding the structure-bonding-property relationships. Our work has presented the following results: (1) Understanding the relationship between compositions and properties in LaFe13-xSix system: A detailed structural and theoretical investigation provided the understanding of the role of a third element on stabilizing the structure and controlling the transformation of cubic NaZn13-type structures to the tetragonal derivative, as well as the relationship between the structures and properties. (2) Synthesis of new ternary rare-earth iron silicides RE2-xFe4Si14-y and proposed superstructure: This compound offers complex structural challenges such as fractional occupancies and their ordering in superstructure. (3) Electronic structure calculation of FeSi2: This shows that the metal-semiconductor phase transition depends on the structure. The mechanism of band gap opening is described in terms of bonding and structural distortion. This result shows that the electronic structure calculations are an essential tool for understanding the relationship between structure and chemical bonding in these compounds. (4) Synthesis of new ternary rare-earth Zinc aluminides Tb3Zn3.6Al7.4: Partially ordered structure of Tb3.6Zn13-xAl7.4 compound provides new insights into the formation, composition and structure of rare-earth transition-metal intermetallics. Electronic structure calculations attribute the observed composition to optimizing metal-metal bonding in the electronegative (Zn, Al) framework, while the specific ordering is strongly influenced by specific orbital interactions. (5) Synthesis of new structure type of Zn39(CrxAl1-x

  3. Rare-earth elements

    International Nuclear Information System (INIS)

    Leveque, A.; Maestro, P.

    1993-01-01

    Production process of rare earths come from hydro-metallurgy treatments including following successive steps from enrichment ores: ore etching by humid way, from obtained solutions separations and purifications using selective precipitation engineering (rare earths case with an oxidation degree different from III), sometimes exchange techniques of ion on resin but principally extraction techniques by solvent; obtaining final products (oxides, salts) or metals elaboration by electrolytic melt salts process at high temperature. About applications, specificity of rare earths is in their particular electronic structure which induces chemical, structural, and physical properties seen as unrivalled ones. These properties are used in industrial applications which are diversified and sophisticated as metallurgy, catalysis, glass, optics, ceramics, luminescence, magnetism, electronics... 44 refs., 6 figs., 7 tabs

  4. Structural Transformation from Dimerization to Tetramerization of Serine-Decorated Rare-Earth-Incorporated Arsenotungstates Induced by the Usage of Rare-Earth Salts.

    Science.gov (United States)

    Li, Hai-Lou; Liu, Ya-Jie; Liu, Jing-Lin; Chen, Li-Juan; Zhao, Jun-Wei; Yang, Guo-Yu

    2017-02-21

    Three types of serine-decorated rare- earth-containing arsenotungstate [H 2 N(CH 3 ) 2 ] 6 NaH[RE 2 W 4 O 10 (H 2 O) 8 (Ser) 2 (B-α-AsW 9 O 33 ) 2 ]⋅30 H 2 O (RE 3+ =Eu 3+ , Gd 3+ , Tb 3+ , Dy 3+ , Ho 3+ , Er 3+ , Tm 3+ , Yb 3+ , and Y 3+ ; 1), [H 2 N(CH 3 ) 2 ] 6 Na 6-x RE x H 4-2 x [RE 4 W 8 O 19 (H 2 O) 10+y (OH) 2 (Ser) 2 (B-α-AsW 9 O 33 ) 4 ]⋅n H 2 O (RE 3+ =Tb 3+ , x=1, y=2, n=36; RE 3+ =Dy 3+ , Ho 3+ , Er 3+ , Yb 3+ , Y 3+ , x=0, y=0, n=38; RE 3+ = Tm 3+ , x=1, y=0, n=38; Ser=serine; 2), and [H 2 N(CH 3 ) 2 ] 6-2 x Na 2+3 x RE x H 10-6 x+y [RE 4 W 8 O 19 (H 2 O) 8 (OH) 2 (Ser) 4 (B-α-AsW 9 O 33 ) 4 ]⋅Cl y ⋅n H 2 O (RE 3+ =Ce 3+ , Pr 3+ , x=1, y=0, n=65; RE 3+ =Nd 3+ , Sm 3+ , x=0, y=0, n=65; RE 3+ =Eu 3+ , Gd 3+ , x=1, y=2, n=45; 3) were synthesized with the participation of the organic solubilizers dimethylamine hydrochloride and l-serine and were structurally characterized. The use of different amounts of rare-earth salts results in the structural transformation from dimerization to tetramerization of types 1-3. Type 1 is a dimeric sandwich-type assembly of a dual-Ser-participating [RE 2 W 4 O 10 (H 2 O) 8 (Ser) 2 ] 10+ entity sandwiched by two [B-α-AsW 9 O 33 ] 9- moieties, whereas types 2 and 3 have a tetrameric square structure formed by four [B-α-AsW 9 O 33 ] 9- moieties that anchor a dual/tetra- Ser-participating [RE 4 W 8 O 19 (H 2 O) 10+y (OH) 2 (Ser) 2 ] 20+ or [RE 4 W 8 O 19 (H 2 O) 8 (OH) 2 (Ser) 4 ] 20+ core. The solid-state luminescence properties and lifetime-decay behaviors of these compounds were investigated. The chromaticity coordinates, dominant wavelengths, color purities, and correlated color temperatures were also calculated. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Effects of Rare Earth Metal Addition on Wear Resistance of Chromium-Molybdenum Cast Steel

    Directory of Open Access Journals (Sweden)

    Kasinska J.

    2017-09-01

    Full Text Available This paper discusses changes in the microstructure and abrasive wear resistance of G17CrMo5-5 cast steel modified with rare earth metals (REM. The changes were assessed using scanning microscopy. The wear response was determined in the Miller test to ASTM G75. Abrasion tests were supplemented with the surface profile measurements of non-modified and modified cast steel using a Talysurf CCI optical profilometer. It was demonstrated that the modification substantially affected the microstructure of the alloy, leading to grain size reduction and changed morphology of non-metallic inclusions. The observed changes in the microstructure resulted in a three times higher impact strength (from 33 to 99 kJ/cm2 and more than two times higher resistance to cracking (from 116 to 250 MPa. The following surface parameters were computed: Sa: Arithmetic mean deviation of the surface, Sq: Root-mean-square deviation of the surface, Sp: Maximum height of the peak Sv: Maximum depth of the valley, Sz: Ten Point Average, Ssk: Asymmetry of the surface, Sku: Kurtosis of the surface. The findings also indicated that the addition of rare earth metals had a positive effect on the abrasion behaviour of G17CrMo5-5 cast steel.

  6. Structurally triggered metal-insulator transition in rare-earth nickelates.

    Science.gov (United States)

    Mercy, Alain; Bieder, Jordan; Íñiguez, Jorge; Ghosez, Philippe

    2017-11-22

    Rare-earth nickelates form an intriguing series of correlated perovskite oxides. Apart from LaNiO 3 , they exhibit on cooling a sharp metal-insulator electronic phase transition, a concurrent structural phase transition, and a magnetic phase transition toward an unusual antiferromagnetic spin order. Appealing for various applications, full exploitation of these compounds is still hampered by the lack of global understanding of the interplay between their electronic, structural, and magnetic properties. Here we show from first-principles calculations that the metal-insulator transition of nickelates arises from the softening of an oxygen-breathing distortion, structurally triggered by oxygen-octahedra rotation motions. The origin of such a rare triggered mechanism is traced back in their electronic and magnetic properties, providing a united picture. We further develop a Landau model accounting for the metal-insulator transition evolution in terms of the rare-earth cations and rationalizing how to tune this transition by acting on oxygen rotation motions.

  7. Assessment of the Lake Gendabi salt for trace elements and toxic heavy metals by energy dispersive X-ray fluorescence spectrometry

    International Nuclear Information System (INIS)

    Lugendo, I.; Mohammed, N.K.; Spyrou, N.M.

    2013-01-01

    This study has analyzed samples of salts from Lake Gendabi, located in the northern part of Tanzania for metal contamination using the EDXRF spectrometry. The aim of the study was to assess the suitability of the salt from Lake Gendabi for human consumption. Seventy-five samples of salt were collected from the Lake Gendabi floor and grouped into five grades (G1, G2, G3, G4 and G5) depending on the position of the salt from the lake shore. In addition to Na and Cl, concentrations of 17 more elements were determined in all five grades of salt. These included seven toxic metals which are Al, Ni, Cr, Cd, Pb as well as Th and U which are both toxic and radioactive. The concentrations of all toxic elements found in the samples were higher than their Maximum tolerable limits set by international organizations. As this salt is used in many parts of Tanzania, it is proposed that the salt should be thoroughly purified before entering the market. Further research to include salt samples from other salt production areas in Tanzania is recommended. (author)

  8. The production of HTR-fuel kernels by microwave hardening of aqueous metal-salt-resin droplets

    International Nuclear Information System (INIS)

    Knotik, K.; Leichter, P.

    1981-04-01

    The construction and function of the microwave equipment for the hardening of free falling salt-resin-droplets, the preparation of solutions, their treatment and conditioning of the hardening process, the appearance and properties of the hardened ''green'' kernels and the transformation of ''green'' kernels of HTR-fuel kernels, i.e. sintered UO 2 -particles are described. With a suitable microwave equipment it is possible to harden aqueous droplets containing metal-salts (e.g. uranylnitrate), resorcinol and formaldehyde. The hardening occurs while the mentioned droplets are falling under gravity. These particles are suitable for the production of HTR-fuel kernels, e.g. high density UO 2 -particles. The entire process has the advantage of minimising the process specific waste. (author)

  9. Cesium Platinide Hydride 4Cs 2 Pt-CsH: An Intermetallic Double Salt Featuring Metal Anions

    Energy Technology Data Exchange (ETDEWEB)

    Smetana, Volodymyr [Ames Laboratory, US Department of Energy, and Critical Materials Institute, Ames Iowa 50011-3020 USA; Mudring, Anja-Verena [Ames Laboratory, US Department of Energy, and Critical Materials Institute, Ames Iowa 50011-3020 USA; Department of Materials Sciences and Engineering, Iowa State University, Ames Iowa 50011-3111 USA

    2016-10-24

    With Cs9Pt4H a new representative of ionic compounds featuring metal anions can be added to this rare-membered family. Cs9Pt4H exhibits a complex crystal structure containing Cs+ cations, Pt2- and H- anions. Being a red, transparent compound its band gap is in the visible range of the electromagnetic spectrum and the ionic type of bonding is confirmed by quantum chemical calculations. This cesium platinide hydride can formally be considered as a double salt of the “alloy” cesium–platinum, or better cesium platinide, Cs2Pt, and the salt cesium hydride CsH according to Cs9Pt4H≡4 Cs2Pt∙CsH.

  10. Cesium platinide hydride 4Cs{sub 2}Pt.CsH: an intermetallic double salt featuring metal anions

    Energy Technology Data Exchange (ETDEWEB)

    Smetana, Volodymyr [Ames Laboratory, US Department of Energy, and Critical Materials Institute, Ames, Iowa, 50011-3020 (United States); Mudring, Anja-Verena [Ames Laboratory, US Department of Energy, and Critical Materials Institute, Ames, Iowa, 50011-3020 (United States); Department of Materials Sciences and Engineering, Iowa State University, Ames, Iowa, 50011-3111 (United States)

    2016-11-14

    With Cs{sub 9}Pt{sub 4}H a new representative of ionic compounds featuring metal anions can be added to this rare-membered family. Cs{sub 9}Pt{sub 4}H exhibits a complex crystal structure containing Cs{sup +} cations, Pt{sup 2-} and H{sup -} anions. Being a red, transparent compound its band gap is in the visible range of the electromagnetic spectrum and the ionic type of bonding is confirmed by quantum chemical calculations. This cesium platinide hydride can formally be considered as a double salt of the ''alloy'' cesium-platinum, or better cesium platinide, Cs{sub 2}Pt, and the salt cesium hydride CsH according to Cs{sub 9}Pt{sub 4}H≡4 Cs{sub 2}Pt.CsH. (copyright 2016 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Cesium platinide hydride 4Cs2Pt.CsH: an intermetallic double salt featuring metal anions

    International Nuclear Information System (INIS)

    Smetana, Volodymyr; Mudring, Anja-Verena

    2016-01-01

    With Cs 9 Pt 4 H a new representative of ionic compounds featuring metal anions can be added to this rare-membered family. Cs 9 Pt 4 H exhibits a complex crystal structure containing Cs + cations, Pt 2- and H - anions. Being a red, transparent compound its band gap is in the visible range of the electromagnetic spectrum and the ionic type of bonding is confirmed by quantum chemical calculations. This cesium platinide hydride can formally be considered as a double salt of the ''alloy'' cesium-platinum, or better cesium platinide, Cs 2 Pt, and the salt cesium hydride CsH according to Cs 9 Pt 4 H≡4 Cs 2 Pt.CsH. (copyright 2016 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  12. Application of Freeze-Dried Powders of Genetically Engineered Microbial Strains as Adsorbents for Rare Earth Metal Ions.

    Science.gov (United States)

    Moriwaki, Hiroshi; Masuda, Reiko; Yamazaki, Yuki; Horiuchi, Kaoru; Miyashita, Mari; Kasahara, Jun; Tanaka, Tatsuhito; Yamamoto, Hiroki

    2016-10-12

    The adsorption behaviors of the rare earth metal ions onto freeze-dried powders of genetically engineered microbial strains were compared. Cell powders obtained from four kinds of strains, Bacillus subtilis 168 wild type (WT), lipoteichoic acid-defective (ΔLTA), wall teichoic acid-defective (ΔWTA), and cell wall hydrolases-defective (EFKYOJLp) strains, were used as an adsorbent of the rare earth metal ions at pH 3. The adsorption ability of the rare earth metal ions was in the order of EFKYOJLp > WT > ΔLTA > ΔWTA. The order was the same as the order of the phosphorus quantity of the strains. This result indicates that the main adsorption sites for the ions are the phosphate groups and the teichoic acids, LTA and WTA, that contribute to the adsorption of the rare earth metal ions onto the cell walls. The contribution of WTA was clearly greater than that of LTA. Each microbial powder was added to a solution containing 16 kinds of rare earth metal ions, and the removals (%) of each rare earth metal ion were obtained. The scandium ion showed the highest removal (%), while that of the lanthanum ion was the lowest for all the microbial powders. Differences in the distribution coefficients between the kinds of lanthanide ions by the EFKYOJLp and ΔWTA powders were greater than those of the other strains. Therefore, the EFKYOJLp and ΔWTA powders could be applicable for the selective extraction of the lanthanide ions. The ΔLTA powder coagulated by mixing with a rare earth metal ion, although no sedimentation of the WT or ΔWTA powder with a rare earth metal ion was observed under the same conditions. The EFKYOJLp powder was also coagulated, but its flocculating activity was lower than that of ΔLTA. The ΔLTA and EFKYOJLp powders have a long shape compared to those of the WT or ΔWTA strain. The shapes of the cells will play an important role in the sedimentation of the microbial powders with rare earth metal ions. As the results, three kinds of the genetically

  13. Reinecke's Salt Revisited. An Undergraduate Project Involving an Unknown Metal Complex.

    Science.gov (United States)

    Searle, Graeme H.; And Others

    1989-01-01

    Describes 10 experiments for characterizing the chromium complex Reinecke's Salt. The properties of the complex, experimental procedures, and a discussion are provided. Analyses are presented for chromium, total ammonia, thiocyanate, ammonium ion, and hydrate water. Measurement methods are described. (YP)

  14. Electrodeposition of Transition Metal-Aluminum Alloys from Chloroaluminate Molten Salts

    National Research Council Canada - National Science Library

    Hussey, Charles

    2004-01-01

    .... Many of these alloys, notably Al-Mo and Al-W, exhibited outstanding resistance to chloride-induced pitting corrosion, making them useful corrosion protective coatings for Air Force applications in high-salt environments.

  15. Kinetics of the mechanochemical synthesis of alkaline-earth metal amides

    Science.gov (United States)

    Garroni, Sebastiano; Takacs, Laszlo; Leng, Haiyan; Delogu, Francesco

    2014-07-01

    A phenomenological framework is developed to model the kinetics of the formation of alkaline-earth metal amides by the ball milling induced reaction of their hydrides with gaseous ammonia. It is shown that the exponential character of the kinetic curves is modulated by the increase of the total volume of the powder inside the reactor due to the substantially larger molar volume of the products compared to the reactants. It is claimed that the volume of powder effectively processed during each collision connects the transformation rate to the physical and chemical processes underlying the mechanochemical transformations.

  16. The role of the smooth cordgrass Spartina alterniflora and associated sediments in the heavy metal biogeochemical cycle within Bahia Blanca estuary salt marshes

    Energy Technology Data Exchange (ETDEWEB)

    Hempel, M. [Dept. of Environmental Process Engineering, International Graduate School Zittau, Zittau (Germany); Botte, S.E. [Area de Oceanografia Quimica, Inst. Argentino de Oceanografia (IADO), CCT-CONICET, Bahia Blanca (Argentina); Dept. de Biologia, Bioquimica y Farmacia (DBBF), Univ. Nacional del Sur (UNS), Bahia Blanca (Argentina); Negrin, V.L.; Chiarello, M.N. [Area de Oceanografia Quimica, Inst. Argentino de Oceanografia (IADO), CCT-CONICET, Bahia Blanca (Argentina); Marcovecchio, J.E. [Area de Oceanografia Quimica, Inst. Argentino de Oceanografia (IADO), CCT-CONICET, Bahia Blanca (Argentina); Facultad Regional Bahia Blanca (UTN-FRBB), Univ. Tecnologica Nacional, Bahia Blanca (Argentina); Univ. FASTA, Mar del Plata (Argentina)

    2008-10-15

    Background, aim, and scope Bahia Blanca estuary is characterized by the occurrence of large intertidal areas, including both naked tidal flats and salt marshes densely vegetated with Spartina alterniflora. The estuary is strongly affected by human activities, including industrial and municipal discharges, harbor maintenance, cargo vessels and boat navigation, oil storage and processing, etc. Even numerous studies have reported the occurrence and distribution of heavy metals in sediments and biota from this estuary, although the function of the halophyte vegetation on metals distribution was at present not studied. The main objective of the present study was to understand the potential role of the salt marshes as a sink or source of metals to the estuary, considering both the obtained data on metal levels within sediments and plants from the studied areas at naked tidal as well as vegetated flats. Conclusions and recommendations Considering the comments on the previous paragraphs, salt marshes from Bahia Blanca estuary are sources or sinks for metals? It can be sustained that both are the case, even if it is often stated that wetlands serve as sinks for pollutants, reducing contamination of surrounding ecosystems (Weis and Weis, Environ Int 30:685-700, 2004). In the present study case, the sediments (which tend to be anoxic and reduced) act as sinks, while the salt marshes can become a source of metal contaminants. This is very important for this system because the macrophytes have been shown to retain the majority of metals in the underground tissues, and particularly in their associated sediments. This fact agreed well with previous reports, such as that from Leendertse et al., (Environ Pollut 94:19-29, 1996) who found that about 50% of the absorbed metals were retained in salt marshes and 50% was exported. Thus, keeping in mind the large spreading of S. alterniflora salt marshes within Bahia Blanca estuary, it must be carefully considered as a redistributor of

  17. Application of Proton Conductors to Hydrogen Monitoring for Liquid Metal and Molten Salt Systems

    Science.gov (United States)

    Kondo, Masatoshi; Muroga, Takeo; Katahira, Koji; Oshima, Tomoko

    The chemical control of impurity such as hydrogen and oxygen in coolants is one of the critical issues for the development of liquid metal cooled fast reactors and self-cooled liquid breeder blankets for fusion reactors. Especially, hydrogen (isotopes) level is the key parameter for corrosion and mechanical properties of the in-reactor components. For fission reactors, the monitor of hydrogen level in the melt is important for safety operation. The control of tritium is essential for the tritium breeding performance of the fusion reactors. Therefore, on-line hydrogen sensing is a key technology for these systems. In the present study, conceptual design for the on-line hydrogen sensor to be used in liquid sodium (Na), lead (Pb), lead-bismuth (Pb-Bi), lithium (Li), lead-lithium (Pb-17Li) and molten salt LiF-BeF2 (Flibe) was performed. The cell of hydrogen sensor is made of a solid electrolyte. The solid electrolyte proposed in this study is the CaZrO3-based ceramics, which is well-known as proton conducting ceramics. In this concept, the cell is immersed into the melt which is containing the hydrogen at the activity of PH1 of ambient atmosphere. Then, the cell is filled with Ar-H2 mixture gas at regulated hydrogen activity of PH2. The electromotive force (EMF) is obtained by the proton conduction in the electro chemical system expressed as Pt, Melt(PH1) | Proton conductor | PH2, Pt. The Nernst equation is used for the evaluation of the hydrogen activity from the obtained EMF. The evaluations of expected performance of the sensor in liquid Na, Pb, Pb-Bi, Pb-17Li, Li and Flibe were carried out by means of the measurement test in gas atmosphere at hydrogen activities equivalent to those for the melts in the reactor conditions. In the test, the hydrogen activity in the gas varied from 2.2x10-14 to 1. The sensor exhibited good response, stability and reproducibility.

  18. Co-selection of antibiotic and metal(loid) resistance in gram-negative epiphytic bacteria from contaminated salt marshes.

    Science.gov (United States)

    Henriques, Isabel; Tacão, Marta; Leite, Laura; Fidalgo, Cátia; Araújo, Susana; Oliveira, Cláudia; Alves, Artur

    2016-08-15

    The goal of this study was to investigate co-selection of antibiotic resistance in gram-negative epiphytic bacteria. Halimione portulacoides samples were collected from metal(loid)-contaminated and non-contaminated salt marshes. Bacterial isolates (n=137) affiliated with Vibrio, Pseudomonas, Shewanella, Comamonas, Aeromonas and with Enterobacteriaceae. Vibrio isolates were more frequent in control site while Pseudomonas was common in contaminated sites. Metal(loid) and antibiotic resistance phenotypes varied significantly according to site contamination, and multiresistance was more frequent in contaminated sites. However, differences among sites were not observed in terms of prevalence or diversity of acquired antibiotic resistance genes, integrons and plasmids. Gene merA, encoding mercury resistance, was only detected in isolates from contaminated sites, most of which were multiresistant to antibiotics. Results indicate that metal(loid) contamination selects for antibiotic resistance in plant surfaces. In salt marshes, antibiotic resistance may be subsequently transferred to other environmental compartments, such as estuarine water or animals, with potential human health risks. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Accumulation of de-icing salts and its short-term effect on metal mobility in urban roadside soils.

    Science.gov (United States)

    Li, Fayun; Zhang, Ying; Fan, Zhiping; Oh, Kokyo

    2015-04-01

    In this study, a field investigation combined with a laboratory column leaching experiment were carried out to assess the effects of de-icing salts application on the heavy metal mobilization in roadside soils in an old and large industrial zone in Northeastern China. In the field investigation, 41 roadside soils were collected from the industrial zone, and the results showed a strong rise in deicing salts related concentrations of Na (352-513 mg/kg) and Cl (577-2,353 mg/kg) and high values of Cd (1.2-7.6 mg/kg) and Pb (28.7-101.6 mg/kg). The most serious contaminated roadside soil was used for column leaching experiment alternately with de-icing salts solution and deionized water to simulate the runoff of de-icing salts into roadside soils followed by snowmelt or rainwater. The results showed that an extensive mobilization of Cd (20.90 % of the total Cd in the soil) occurred in the salt leachate, and a high correlation with Cl were found, indicating that Cl complexes are important for the mobilization. Conversely, only 2.34 % of the total amount of Pb in the soil was leached, confirming the usual hypotheses about the high immobility of Pb in soils. However, it was found that high Pb concentration coincided with peaks in Fe and TOC concentrations, and the proportion of Pb in the >0.45 µm phase was much low, which implied an extensive Pb mobilization with small-sized colloids.

  20. First-principles study of the alkali earth metal atoms adsorption on graphene

    Science.gov (United States)

    Sun, Minglei; Tang, Wencheng; Ren, Qingqiang; Wang, Sake; JinYu; Du, Yanhui; Zhang, Yajun

    2015-11-01

    Geometries, electronic structures, and magnetic properties for alkali earth metal atoms absorbed graphene have been studied by first-principle calculations. For Be and Mg atoms, the interactions between the adatom and graphene are weak van der Waals interactions. In comparison, Ca, Sr and Ba atoms adsorption on graphene exhibits strong ionic bonding with graphene. We found that these atoms bond to graphene at the hollow site with a significant binding energy and large electron transfer. It is intriguing that these adatoms may induce important changes in both the electronic and magnetic properties of graphene. Semimetal graphene becomes metallic and magnetic due to n-type doping. Detailed analysis shows that the s orbitals of these adatoms should be responsible for the arising of the magnetic moment. We believe that our results are suitable for experimental exploration and useful for graphene-based nanoelectronic and data storage.

  1. Anomalous positive flatband voltage shifts in metal gate stacks containing rare-earth oxide capping layers

    KAUST Repository

    Caraveo-Frescas, J. A.

    2012-03-09

    It is shown that the well-known negative flatband voltage (VFB) shift, induced by rare-earth oxide capping in metal gate stacks, can be completely reversed in the absence of the silicon overlayer. Using TaN metal gates and Gd2O3-doped dielectric, we measure a ∼350 mV negative shift with the Si overlayer present and a ∼110 mV positive shift with the Si overlayer removed. This effect is correlated to a positive change in the average electrostatic potential at the TaN/dielectric interface which originates from an interfacial dipole. The dipole is created by the replacement of interfacial oxygen atoms in the HfO2 lattice with nitrogen atoms from TaN.

  2. Metal and alloy nanoparticles by amine-borane reduction of metal salts by solid-phase synthesis: atom economy and green process.

    Science.gov (United States)

    Sanyal, Udishnu; Jagirdar, Balaji R

    2012-12-03

    A new solid state synthetic route has been developed toward metal and bimetallic alloy nanoparticles from metal salts employing amine-boranes as the reducing agent. During the reduction, amine-borane plays a dual role: acts as a reducing agent and reduces the metal salts to their elemental form and simultaneously generates a stabilizing agent in situ which controls the growth of the particles and stabilizes them in the nanosize regime. Employing different amine-boranes with differing reducing ability (ammonia borane (AB), dimethylamine borane (DMAB), and triethylamine borane (TMAB)) was found to have a profound effect on the particle size and the size distribution. Usage of AB as the reducing agent provided the smallest possible size with best size distribution. Employment of TMAB also afforded similar results; however, when DMAB was used as the reducing agent it resulted in larger sized nanoparticles that are polydisperse too. In the AB mediated reduction, BNH(x) polymer generated in situ acts as a capping agent whereas, the complexing amine of the other amine-boranes (DMAB and TMAB) play the same role. Employing the solid state route described herein, monometallic Au, Ag, Cu, Pd, and Ir and bimetallic CuAg and CuAu alloy nanoparticles of <10 nm were successfully prepared. Nucleation and growth processes that control the size and the size distribution of the resulting nanoparticles have been elucidated in these systems.

  3. Earth

    CERN Document Server

    Carter, Jason

    2017-01-01

    This curriculum-based, easy-to-follow book teaches young readers about Earth as one of the eight planets in our solar system in astronomical terms. With accessible text, it provides the fundamental information any student needs to begin their studies in astronomy, such as how Earth spins and revolves around the Sun, why it's uniquely suitable for life, its physical features, atmosphere, biosphere, moon, its past, future, and more. To enhance the learning experience, many of the images come directly from NASA. This straightforward title offers the fundamental information any student needs to sp

  4. Mechanistic study on ultrasound assisted pretreatment of sugarcane bagasse using metal salt with hydrogen peroxide for bioethanol production.

    Science.gov (United States)

    Ramadoss, Govindarajan; Muthukumar, Karuppan

    2016-01-01

    This study presents the ultrasound assisted pretreatment of sugarcane bagasse (SCB) using metal salt with hydrogen peroxide for bioethanol production. Among the different metal salts used, maximum holocellulose recovery and delignification were achieved with ultrasound assisted titanium dioxide (TiO2) pretreatment (UATP) system. At optimum conditions (1% H2O2, 4 g SCB dosage, 60 min sonication time, 2:100 M ratio of metal salt and H2O2, 75°C, 50% ultrasound amplitude and 70% ultrasound duty cycle), 94.98 ± 1.11% holocellulose recovery and 78.72 ± 0.86% delignification were observed. The pretreated SCB was subjected to dilute acid hydrolysis using 0.25% H2SO4 and maximum xylose, glucose and arabinose concentration obtained were 10.94 ± 0.35 g/L, 14.86 ± 0.12 g/L and 2.52 ± 0.27 g/L, respectively. The inhibitors production was found to be very less (0.93 ± 0.11 g/L furfural and 0.76 ± 0.62 g/L acetic acid) and the maximum theoretical yield of glucose and hemicellulose conversion attained were 85.8% and 77%, respectively. The fermentation was carried out using Saccharomyces cerevisiae and at the end of 72 h, 0.468 g bioethanol/g holocellulose was achieved. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis of pretreated SCB was made and its morphology was studied using scanning electron microscopy (SEM). The compounds formed during the pretreatment were identified using gas chromatography-mass spectrometry (GC-MS) analysis. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Thermal Analysis of Surrogate Simulated Molten Salts with Metal Chloride Impurities for Electrorefining Used Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Toni Y. Gutknecht; Guy L. Fredrickson; Vivek Utgikar

    2012-04-01

    This project is a fundamental study to measure thermal properties (liquidus, solidus, phase transformation, and enthalpy) of molten salt systems of interest to electrorefining operations, which are used in both the fuel cycle research & development mission and the spent fuel treatment mission of the Department of Energy. During electrorefining operations the electrolyte accumulates elements more active than uranium (transuranics, fission products and bond sodium). The accumulation needs to be closely monitored because the thermal properties of the electrolyte will change as the concentration of the impurities increases. During electrorefining (processing techniques used at the Idaho National Laboratory to separate uranium from spent nuclear fuel) it is important for the electrolyte to remain in a homogeneous liquid phase for operational safeguard and criticality reasons. The phase stability of molten salts in an electrorefiner may be adversely affected by the buildup of fission products in the electrolyte. Potential situations that need to be avoided are: (i) build up of fissile elements in the salt approaching the criticality limits specified for the vessel (ii) freezing of the salts due to change in the liquidus temperature and (iii) phase separation (non-homogenous solution) of elements. The stability (and homogeneity) of the phases can potentially be monitored through the thermal characterization of the salts, which can be a function of impurity concentration. This work describes the experimental results of typical salts compositions, consisting of chlorides of strontium, samarium, praseodymium, lanthanum, barium, cerium, cesium, neodymium, sodium and gadolinium (as a surrogate for both uranium and plutonium), used in the processing of used nuclear fuels. Differential scanning calorimetry was used to analyze numerous salt samples providing results on the thermal properties. The property of most interest to pyroprocessing is the liquidus temperature. It was

  6. Rare earth metals in North America; Zeldzame aardmetalen in Noord-Amerika

    Energy Technology Data Exchange (ETDEWEB)

    Louzada, K.

    2012-11-15

    The uncertain supply of rare earth metals (Rare Earth Elements) from China for the high tech industry in the U.S. is a barrier for innovation and the high-tech manufacturing industry. Many rare earths are applied in permanent magnets for sustainable energy generation and for energy storage systems in for example electric cars. Also other sectors feel the pressure of shortages. The federal government in the USA and US companies use the opportunity to encourage research into recycling, reducing the use and finding alternatives for rare earths. Canada sees in the uncertain supply and dwindling reserves in the USA and elsewhere an economic opportunity. Canada can start the development of hitherto unprofitable reserves of valuable materials. Both in the USA and Canada, the number of exploration projects in the mining industry has grown significantly [Dutch] De onzekere aanvoer van zeldzame aardmetalen (Rare Earth Elements) uit China voor de hightechindustrie vormt in de VS een hindernis voor innovatie en voor de hightech maakindustrie. Met name in permanente magneten voor duurzame energieopwekking en energieopslagsystemen voor bijvoorbeeld elektrische auto's worden veel zeldzame aardmetalen verwerkt. Ook andere sectoren staan onder druk. De federale overheid en bedrijven in de VS maken van de gelegenheid gebruik om onderzoek naar de recycling, vermindering van het gebruik en alternatieven voor zeldzame aardmetalen te stimuleren. Canada ziet de onzekere aanvoer en slinkende reserves in de VS en elders als een economische kans. Het land kan tot nu toe onrendabele voorkomens van de waardevolle materialen gaan ontwikkelen. Zowel in de VS als in Canada is het aantal exploratieprojecten in de mijnbouw aanzienlijk gegroeid.

  7. Sensitizing Efficiency of Some Added Metal Salts on the Thermal and Explosive Characteristics of Hydrazenium Monoperchlorate and Hydrazenium Diperchlorate

    OpenAIRE

    C. Prabhakaran; N. Sadasivan

    1981-01-01

    Sensitivity to heat, impact and friction of hydrazenium-monoperchlorate and hydrazenium-diperchlorate have been investigated and the sensitizing efficiency of some added metal salts evaluated. The thermal sensitizing efficiency of the additives follow the order CuCrO/sub 4/ > CuCl/sub 2/ >NiO > Fe/sub 2/O/sub 3/ > MgO. The activation energy values obtained from explosion delay time are comparable with the values reported for thermal decomposition studies and are close to the activ...

  8. Metallic reductant-free synthesis of α-substituted propionic acid derivatives through hydrocarboxylation of alkenes with a formate salt.

    Science.gov (United States)

    Takaya, Jun; Miyama, Ko; Zhu, Chuan; Iwasawa, Nobuharu

    2017-04-04

    A PGeP-pincer palladium-catalyzed hydrocarboxylation of styrenes to obtain pharmaceutically important α-arylpropionic acid derivatives was achieved using a formate salt as both a reductant and a CO 2 source. The reaction was also applicable to vinylsulfone and acrylates. Isotope labeling experiments demonstrated that a CO 2 -recycling mechanism is operative through generation and reaction of a benzylpalladium complex as a carbon nucleophile. This protocol has realized a mild and atom economical CO 2 -fixation reaction without the necessity of using strong metallic reductants.

  9. Tensorial analysis of the long-range interaction between metastable alkaline-earth-metal atoms

    International Nuclear Information System (INIS)

    Santra, Robin; Greene, Chris H.

    2003-01-01

    Alkaline-earth-metal atoms in their lowest (nsnp) 3 P 2 state are exceptionally long lived and can be trapped magnetically. The nonspherical atomic structure leads to anisotropic long-range interactions between two metastable alkaline-earth-metal atoms. The anisotropy affects the rotational motion of the diatomic system and couples states of different rotational quantum numbers. This paper develops a tensorial decomposition of the most important long-range interaction operators, and a systematic inclusion of molecular rotations, in the presence of an external magnetic field. This analysis illuminates the nature of the coupling between the various degrees of freedom. The consequences are illustrated by application to a system of practical interest: metastable 88 Sr. Using atomic parameters determined in a nearly ab initio calculation, we compute adiabatic potential-energy curves. The anisotropic interatomic interaction, in combination with the applied magnetic field, is demonstrated to induce the formation of a long-range molecular potential well. This curve correlates to two fully polarized, low-field seeking atoms in a rotational s-wave state. The coupling among molecular rotational states controls the existence of the potential well, and its properties vary as a function of magnetic-field strength, thus allowing the scattering length in this state to be tuned. The scattering length of metastable 88 Sr displays a resonance at a field of 339 G

  10. Contribution to the study of point defects in rare earth metals

    International Nuclear Information System (INIS)

    Boidron, Michel.

    1980-12-01

    In connection with anomalous diffusion in rare earth metals, the different hypothesis put forward to account for this problem are reviewed. After the determination of the activation volume for self diffusion in γ c.c. lanthanum (0,1 mol.), we point out that diffusion data in rare earth metals and actinides cannot be connected with f.d type electronic transition. Diffusion experiments leading to indirect conclusion, positron annihilation experiments have been undertaken. Vacancy formation energies have thus been determined in γ cerium (0.72 +- 0.07 eV) and europium (0.73 +- 0.17 eV); anomalies in the curves are discussed. A self diffusion mechanism via relaxed vacancies is proposed for γ cerium, such an hypothesis being valid for centred cubic phases. In a second part, neutron irradiations of europium at 20 K lead mainly to interstitials properties (recovery stage centred at 71 K interpreted as stage I and corresponding activation energy for migration: 0.22 +- 0.06 eV). The observed linear relation between migration energy and the peak temperature of the recovery stage has been quantitatively demonstrated (stage I: Em(eV) approximately Q.003 TID (K)) [fr

  11. Dipole polarizability of alkali-metal (Na, K, Rb)-alkaline-earth-metal (Ca, Sr) polar molecules: Prospects for alignment

    Science.gov (United States)

    Gopakumar, Geetha; Abe, Minori; Hada, Masahiko; Kajita, Masatoshi

    2014-06-01

    Electronic open-shell ground-state properties of selected alkali-metal-alkaline-earth-metal polar molecules are investigated. We determine potential energy curves of the 2Σ+ ground state at the coupled-cluster singles and doubles with partial triples (CCSD(T)) level of electron correlation. Calculated spectroscopic constants for the isotopes (23Na, 39K, 85Rb)-(40Ca, 88Sr) are compared with available theoretical and experimental results. The variation of the permanent dipole moment (PDM), average dipole polarizability, and polarizability anisotropy with internuclear distance is determined using finite-field perturbation theory at the CCSD(T) level. Owing to moderate PDM (KCa: 1.67 D, RbCa: 1.75 D, KSr: 1.27 D, RbSr: 1.41 D) and large polarizability anisotropy (KCa: 566 a.u., RbCa: 604 a.u., KSr: 574 a.u., RbSr: 615 a.u.), KCa, RbCa, KSr, and RbSr are potential candidates for alignment and orientation in combined intense laser and external static electric fields.

  12. Rare-earth metal oxide doped transparent mesoporous silica plates under non-aqueous condition as a potential UV sensor.

    Science.gov (United States)

    Lee, Sang-Joon; Park, Sung Soo; Lee, Sang Hyun; Hong, Sang-Hyun; Ha, Chang-Sik

    2013-11-01

    Transparent mesoporous silica plates doped with rare-earth metal oxide were prepared using solvent-evaporation method based on the self-organization between structure-directing agent and silicate in a non-aqueous solvent. A triblock copolymer, Pluronic (F127 or P123), was used as the structure-directing agent, while tetraethyl orthosilicate (TEOS) was used as a silica source. The pore diameter and the surface area of the mesoporous silica plate prepared with the optimized conditions were ca 40 A and 600 m2 g(-1), respectively, for both structure-directing agent. Rare-earth metal oxides (Eu, Tb, Tm oxide) in mesochannel were formed via one-step synthetic route based on the preparation method of a silica plate. Optical properties of rare-earth metal oxide-doped mesoporous silica plates were investigated by UV irradiation and photoluminescence (PL) spectroscopy. Under the exitation wavelength of 254 nm, the doped mesoporous silica plates emitted red, green and blue for Eu, Tb and Tm oxides, respectively. Rare-earth metal oxide-doped mesoporous silica plates showed enhanced PL intensity compared to that of the bulk rare-earth metal oxide.

  13. The atmospheric circulation of the super Earth GJ 1214b: Dependence on composition and metallicity

    International Nuclear Information System (INIS)

    Kataria, T.; Showman, A. P.; Fortney, J. J.; Marley, M. S.; Freedman, R. S.

    2014-01-01

    We present three-dimensional atmospheric circulation models of GJ 1214b, a 2.7 Earth-radius, 6.5 Earth-mass super Earth detected by the MEarth survey. Here we explore the planet's circulation as a function of atmospheric metallicity and atmospheric composition, modeling atmospheres with a low mean molecular weight (MMW; i.e., H 2 -dominated) and a high MMW (i.e., water- and CO 2 -dominated). We find that atmospheres with a low MMW have strong day-night temperature variations at pressures above the infrared photosphere that lead to equatorial superrotation. For these atmospheres, the enhancement of atmospheric opacities with increasing metallicity lead to shallower atmospheric heating, larger day-night temperature variations, and hence stronger superrotation. In comparison, atmospheres with a high MMW have larger day-night and equator-to-pole temperature variations than low MMW atmospheres, but differences in opacity structure and energy budget lead to differences in jet structure. The circulation of a water-dominated atmosphere is dominated by equatorial superrotation, while the circulation of a CO 2 -dominated atmosphere is instead dominated by high-latitude jets. By comparing emergent flux spectra and light curves for 50× solar and water-dominated compositions, we show that observations in emission can break the degeneracy in determining the atmospheric composition of GJ 1214b. The variation in opacity with wavelength for the water-dominated atmosphere leads to large phase variations within water bands and small phase variations outside of water bands. The 50× solar atmosphere, however, yields small variations within water bands and large phase variations at other characteristic wavelengths. These observations would be much less sensitive to clouds, condensates, and hazes than transit observations.

  14. Electronic Tongue for Qualitative Analysis of Aqueous Solutions of Salts Using Thick-film Technology and Metal Electrodes

    Directory of Open Access Journals (Sweden)

    Juan Soto

    2006-09-01

    Full Text Available An electronic tongue for the qualitative analysis of aqueous solutions of salts hasbeen developed. The following set of electrodes was used: RuO2, Ag, and Cu in thick-filmtechnology and Au, Pb, Zn and Ni as small bars of the corresponding metal. The response ofthe designed “electronic tongue” was tested on a family of samples containing pure salt andcomplex mixtures. The electrodes were used as potentiometric un-specific sensors and thee.m.f. of each electrode in contact with a certain aqueous solution was used as input signalfor a PCA analysis. The study showed that the set of electrodes were capable to discriminatebetween aqueous solutions of salts basically by their different content in anions and cations(the anions SO42-, Cl-, PO4H2-, CO3H-, NO3- and cations Na+ and K+ were studied. In orderto better analyze the basis for the discrimination power shown by the electronic tongue, aquantitative analysis was also envisaged. A fair estimation of the concentrations of thedifferent ions in the solutions studied appeared to be possible using this electronic tonguedesign.Keywords:

  15. Effects of temperature, moisture, and metal salt content on dielectric properties of rice bran associated with radio frequency heating.

    Science.gov (United States)

    Ling, Bo; Liu, Xiaoli; Zhang, Lihui; Wang, Shaojin

    2018-03-13

    Dielectric heating including microwave (MW) and radio frequency (RF) energy has been regarded as alternative thermal treatments for food processing. To develop effective rice bran (RB) stabilization treatments based on RF and MW heating, dielectric properties (DPs) with dielectric constant (ε') and loss factor (ε″) of RB samples at frequencies (10-3000 MHz), temperatures (25-100 °C), moisture content (MC, 10.36-24.69% w.b.) and three metal salt levels (0.05-2.00%) were determined by an open-ended coaxial probe and impedance analyzer. Results indicated that both ε' and ε″ of RB samples increased with increasing temperature and MC. The increase rate was greater at higher temperature and moisture levels than at lower levels, especially at frequencies lower than 300 MHz. Cubic order models were developed to best fit the relationship between DPs of RB samples and temperature/MC at five frequencies with R 2 greater than 0.994. Both ε″ and RF heating rate of RB samples increased significantly with added NaCl (2%), KCl (1%) and Na 6 O 18 P 6 (2%). The obtained data are useful in developing computer models and simulating dielectric heating for RB stabilization and may also provide theoretical basis for synergistic stabilization of RB under combined dielectric heating with metal salts.

  16. Influence of Rare Earth Metals on Microstructure and Inclusions Morphology G17CrMo5-5 Cast Steel

    Directory of Open Access Journals (Sweden)

    Kasińska J.

    2014-10-01

    Full Text Available This paper presents influence of rare earth metals (REM on the microstructure and morphology of non-metallic inclusions of G17CrMo5-5 cast carbon steel The research has been performed on successive industrial melts. Each time about 2000 kg of liquid metal was modified. The REM was in the form of mishmetal of the composition 49, 8% Ce, 21, 8% La, 17, 1% Nd, 5, 5% Pr and 5, 35% the rest of REM. Therareearth metals were put into the ladle during tapping of heat melt from the furnace.

  17. HIGH YIELD AND RAPID SYNTHESES METHODS FOR PRODUCING METALLO-ORGANIC SALTS

    DEFF Research Database (Denmark)

    2005-01-01

    A new method for preparing salts of metal cations and organic acids, especially divalent salts of alkaline earth metal ions from group II of the periodic system and carboxylic acids. The method comprising the use of a high temperature (about 90° or more) and, optionally. high pressure, in order t...... to obtain a higher yield, purity and faster reaction speed than obtained with known synthesis methods. In particular, the present invention relates to the production of strontium salts of carboxylic acids. Novel strontium salts are also provided by the present method....

  18. First-principles study of the alkali earth metal atoms adsorption on graphene

    International Nuclear Information System (INIS)

    Sun, Minglei; Tang, Wencheng; Ren, Qingqiang; Wang, Sake; JinYu; Du, Yanhui; Zhang, Yajun

    2015-01-01

    Graphical abstract: - Highlights: • The adsorption of Be and Mg adatoms on graphene is physisorption. • Ca, Sr, and Ba adatoms bond ionically to graphene and the most stable adsorption site for them is hollow site. • The zero band gap semiconductor graphene becomes metallic and magnetic after the adsorption of Ca, Sr, and Ba adatoms. - Abstract: Geometries, electronic structures, and magnetic properties for alkali earth metal atoms absorbed graphene have been studied by first-principle calculations. For Be and Mg atoms, the interactions between the adatom and graphene are weak van der Waals interactions. In comparison, Ca, Sr and Ba atoms adsorption on graphene exhibits strong ionic bonding with graphene. We found that these atoms bond to graphene at the hollow site with a significant binding energy and large electron transfer. It is intriguing that these adatoms may induce important changes in both the electronic and magnetic properties of graphene. Semimetal graphene becomes metallic and magnetic due to n-type doping. Detailed analysis shows that the s orbitals of these adatoms should be responsible for the arising of the magnetic moment. We believe that our results are suitable for experimental exploration and useful for graphene-based nanoelectronic and data storage.

  19. Technique for recovering rare-earth metals from spent sintered Nd-Fe-B magnets without external heating

    Directory of Open Access Journals (Sweden)

    Ryo Sasai

    2016-06-01

    Full Text Available To selectively recover rare-earth metals with higher purity from spent sintered Nd-Fe-B magnets without external heating, we investigated the mechano-chemical treatment of spent sintered Nd-Fe-B magnet powder with a reaction solution of HCl and (COOH2 at room temperature. The results of various experiments showed that the mechano-chemical treatment with HCl and (COOH2 is very effective for recovering the rare-earth metals contained in spent sintered Nd-Fe-B magnet powder; the recovery rate and purity of the rare-earth metals were 95.3 and 95.0 mass%, respectively, under optimal conditions ([HCl] = 0.2 mol/dm3 and [(COOH2] = 0.25 mol/dm3.

  20. Nickel-plating for active metal dissolution resistance in molten fluoride salts

    Energy Technology Data Exchange (ETDEWEB)

    Olson, Luke [Department of Engineering Physics, 1500 Engineering Drive, University of Wisconsin, Madison, WI 53706 (United States); Sridharan, Kumar, E-mail: kumar@engr.wisc.edu [Department of Engineering Physics, 1500 Engineering Drive, University of Wisconsin, Madison, WI 53706 (United States); Anderson, Mark; Allen, Todd [Department of Engineering Physics, 1500 Engineering Drive, University of Wisconsin, Madison, WI 53706 (United States)

    2011-04-15

    Ni electroplating of Incoloy-800H was investigated with the goal of mitigating Cr dissolution from this alloy into molten 46.5%LiF-11.5%NaF-42%KF eutectic salt, commonly referred to as FLiNaK. Tests were conducted in graphite crucibles at a molten salt temperature of 850 deg. C. The crucible material graphite accelerates the corrosion process due to the large activity difference between the graphite and the alloy. For the purposes of providing a baseline for this study, un-plated Incoloy-800H and a nearly pure Ni-alloy, Ni-201 were also tested. Results indicate that Ni-plating has the potential to significantly improve the corrosion resistance of Incoloy-800H in molten fluoride salts. Diffusion of Cr from the alloy through the Ni-plating does occur and if the Ni-plating is thin enough this Cr eventually dissolves into the molten salt. The post-corrosion test microstructure of the Ni-plating, particularly void formation was also observed to depend on the plating thickness. Diffusion anneals in a helium environment of Ni-plated Incoloy-800H and an Fe-Ni-Cr model alloy were also investigated to understand Cr diffusion through the Ni-plating. Further enhancements in the efficacy of the Ni-plating as a protective barrier against Cr dissolution from the alloy into molten fluoride salts can be achieved by thermally forming a Cr{sub 2}O{sub 3} barrier film on the surface of the alloy prior to Ni electroplating.

  1. Clay mineralogy, grain size distribution and their correlations with trace metals in the salt marsh sediments of the Skallingen barrier spit, Danish Wadden Sea

    DEFF Research Database (Denmark)

    He, Changling; Bartholdy, Jesper; Christiansen, Christian

    2012-01-01

    with the other adsorbents and to low availability of the mobile trace metals in the system. Correlation between trace metals and clay minerals may therefore be used as an indicator in environmental assessment. Fine grain fractions of the sediment increased markedly after salt marsh invasion in about 1931...... metals. The clay assembly of the sediment consists of illite, kaolinite and much less chlorite and smectite. The major clay minerals of illite, kaolinite as well as chlorite correlate very poorly with all the trace metals investigated, due probably to the weak competing strength of these clays compared...... is observed at about 30 µm, around where the correlation coefficient r drops from 0.8 to 0.1. Adsorption is the controlling mechanism for the behavior of trace metals in the salt marsh. Fe/Mn (hydr)oxides and organic matter play the key role....

  2. Complementary experimental-simulational study of surfactant micellar phase in the extraction process of metallic ions: Effects of temperature and salt concentration

    Science.gov (United States)

    Soto-Ángeles, Alan Gustavo; Rodríguez-Hidalgo, María del Rosario; Soto-Figueroa, César; Vicente, Luis

    2018-02-01

    The thermoresponsive micellar phase behaviour that exhibits the Triton-X-100 micelles by temperature effect and addition of salt in the extraction process of metallic ions was explored from mesoscopic and experimental points. In the theoretical study, we analyse the formation of Triton-X-100 micelles, load and stabilization of dithizone molecules and metallic ions extraction inside the micellar core at room temperature; finally, a thermal analysis is presented. In the experimental study, the spectrophotometric outcomes confirm the solubility of the copper-dithizone complex in the micellar core, as well as the extraction of metallic ions of aqueous environment via a cloud-point at 332.2 K. The micellar solutions with salt present a low absorbance value compared with the micellar solutions without salt. The decrease in the absorbance value is attributed to a change in the size of hydrophobic region of colloidal micelles. All transitory stages of extraction process are discussed and analysed in this document.

  3. Validation of ion chromatography for the determination of transition metal ions along with alkali, alkaline earth metal elements for uranium oxide fuel

    International Nuclear Information System (INIS)

    Kelkar, Anoop; Prakash, Amrit; Afzal, Mohd.; Panakkal, J.P.

    2009-02-01

    The present report describes the use of Ion chromatography (IC) methods with spectrophotometric and direct conductivity detection for the determination of transition metal elements and alkali alkaline earth metal ions in UO 2 pellets. Transmet analytical column and Metrosep- cation 1-2 column were used for the separation of transition metal elements and alkali and alkaline earth metal elements respectively. Oxalic acid and mixture of pyridine 2,6-dicarboxylic acid (PDCA), Na 2 SO 4 and NaCl were used as mobile phase for the separation of transition metal ions and monitored after post - column reaction with 4,2-pyridylazo resorcinol (PAR) at 520nm spectrophotometrically. In the determination of alkali and alkaline earth metal ions the interference of transition metals are removed by complexing them with PDCA. Mixture of tartaric acid and PDCA employed in the separation of alkali and alkaline earth metal ions and monitored on direct conductivity detector. Mobile phase composition was optimised for the base line separation. Calibration plots of Fe 3+ , Cu 2+ , Ni 2+ , Co 2+ , Cd 2+ , Mn 2+ , Li + , Na + , K + , Mg 2+ , Ca 2+ and Sr 2+ were linear over a wide dynamic range with regression coefficient better than 0.999. Detection limit of above ions were between 5-30ppb. To prevent the overloading of the cation exchange column, uranium matrix was removed from UO 2 sample by solvent extraction with 30% TBP - TOPO/CCl 4 . Ten sintered UO2 pellets of same lot were analysed and R.S.D. ±10% was obtained. These methods were validated by analysis of ILCE standards of UO 2 . (author)

  4. Fission product removal from molten salt using zeolite

    International Nuclear Information System (INIS)

    Pereira, C.; Babcock, B.D.

    1996-01-01

    Spent nuclear fuel (SNF) can be treated in a molten salt electrorefiner for conversion into metal and mineral waste forms for geologic disposal. The fuel is dissolved in molten chloride salt. Non-transuranic fission products in the molten salt are ion-exchanged into zeolite A, which is subsequently mixed with glass and consolidated. Zeolite was found to be effective in removing fission product cations from the molten salt. Breakthrough of cesium and the alkaline earths occurred more rapidly than was observed for the rare earths. The effluent composition as a function of time is presented, as well as results for the distribution of fission products along the length of the column. Effects of temperature and salt flow rate are also discussed

  5. Effects of rare earth metals addition on the resistance to pitting corrosion of super duplex stainless steel - Part 1

    International Nuclear Information System (INIS)

    Kim, Soon-Tae; Jeon, Soon-Hyeok; Lee, In-Sung; Park, Yong-Soo

    2010-01-01

    To elucidate the effects of rare earth metals addition on the resistance to pitting corrosion of super duplex stainless steel, a metallographic examination, potentiodynamic and potentiostatic polarization tests, a SEM-EDS and a SAM analysis of inclusion, austenite phase and ferrite phase were conducted. The addition of rare earth metals to the base alloy led to the formation of (Mn, Cr, Si, Al, Ce) oxides and (Mn, Cr, Si, Ce) oxides, which improved the resistance to pitting corrosion and caused a decrease in the preferential interface areas for the initiation of the pitting corrosion.

  6. The measurement of metallic uranium solubility in lithium chloride molten salt

    International Nuclear Information System (INIS)

    Park, K. K.; Choi, I. K.; Yeon, J. W.; Choi, K. S.; Park, Y. J.

    2002-01-01

    For the purpose of more precise solubility measurement of metallic uranium in lithium chloride melt, the effect of lithium chloride on uranium determination and and the change of oxidation state of metallic uranium in the media were investigated. Uranium of higher than 10 μg/g could be directly determined by ICP-AES. In the case of the lower concentration, the separation and concentration of uranium by anion exchanger was followed by ICP-AES, thereby extending the measurable concentration to 0.1 μg/g. The effects of lithium oxide, uranium oxides(UO 2 or U 3 O 8 ) and metallic lithium on the solubility of metallic uranium were individually investigated in glassy carbon or stainless steel crucibles under argon gas atmosphere. Since metallic uranium is oxidized to uranium(III) in the absence of metallic lithium, causing an increase in the solubility, metallic lithium as reducing agent should be present in the reaction media to obtain the more precise solubility. The metallic uranium solubilities measured at 660 and 690 .deg. C were both lower than 10 μg/g

  7. Thermodynamics analysis of the rare earth metals and their alloys with indium in solid state

    International Nuclear Information System (INIS)

    Vassiliev, V.P.; Benaissa, Ablazeze; Taldrik, A.F.

    2013-01-01

    Graphical abstract: Gibbs energies of formation vs. RE atomic numbers in REIn 3 . Highlights: •Set of experimental values was collected for REIn 3 phases. •Thermodynamic functions of formation were calculated at 298 K and 775 K. •Experimental and calculated values were compared. -- Abstract: Nonlinear correlative analyses between thermodynamic and some physico-chemical properties of rare-earth metals (RE) and their alloys with indium are performed for the isostructural phases RE and REIn 3 . The thermodynamics values (Gibbs energies of formation, enthalpies of formation, and entropies of formation at 298 K and 775 K and standard entropies) of LnIn 3 phases are calculated on the basis of calorimetry and potentiometry results. The proposed correlation between physico-chemical and thermodynamic properties agrees for all the isostructural phases REX (X are others elements of the periodic table). The resulting thermodynamic data are recommended for metallurgical handbook

  8. Coordination Polymerization of Renewable 3-Methylenecyclopentene with Rare-Earth-Metal Precursors.

    Science.gov (United States)

    Liu, Bo; Li, Shihui; Wang, Meiyan; Cui, Dongmei

    2017-04-10

    Coordination polymerization of renewable 3-methylenecyclopentene has been investigated for the first time using rare-earth metal-based precursors bearing various bulky ligands. All the prepared complexes catalyze controllable polymerization of 3-methylenecyclopentene into high molecular weight polymers, of which the NPN- and NSN-tridentate non-Cp ligated lutetium-based catalytic systems exhibited extremely high activities up to 11 520 kg/(mol Lu ⋅h) in a dilute toluene solution (3.2 g/100 mL) at room temperature. The resultant polymers have pure 1,4-regioregularity (>99 %) and tailorable number average molecular weights (1-20×10 4 ) with narrow molecular weight distributions (polydispersity index (PDI)=1.45-1.79). DFT simulations were employed to study the polymerization mechanism and stereoregularity control. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Coercivity of domain wall motion in thin films of amorphous rare earth-transition metal alloys

    Science.gov (United States)

    Mansuripur, M.; Giles, R. C.; Patterson, G.

    1991-01-01

    Computer simulations of a two dimensional lattice of magnetic dipoles are performed on the Connection Machine. The lattice is a discrete model for thin films of amorphous rare-earth transition metal alloys, which have application as the storage media in erasable optical data storage systems. In these simulations, the dipoles follow the dynamic Landau-Lifshitz-Gilbert equation under the influence of an effective field arising from local anisotropy, near-neighbor exchange, classical dipole-dipole interactions, and an externally applied field. Various sources of coercivity, such as defects and/or inhomogeneities in the lattice, are introduced and the subsequent motion of domain walls in response to external fields is investigated.

  10. Theory of Temperature Dependence of the Magnetization in Rare-Earth-Transition-Metal Alloys

    DEFF Research Database (Denmark)

    Szpunar, B.; Lindgård, Per-Anker

    1977-01-01

    It is shown that the temperature dependence of the magnetic moments and Curie and ferrimagnetic compensation temperatures for Gdl-xTx (T = Co, Ni, and Fe) and Y1-xCox can be accounted for by a simple model assuming a RKKY interaction between the rare-earth moments and the transition-metal pseudo-spin......1-xCox durch ein einfaches Model1 erklärt werden können, das eine RKKY-Wechsel-wirkung zwischen den Momenten der Seltenen Erden und des Pseudo-Spins des Übergangsmetalls annimmt. Die Wechselwirkung wird durch ein effektives Legierungsmedium übermittelt, das mit der CPA-Theorie und elliptischen...

  11. Structural order and magnetism of rare-earth metallic amorphous alloys

    International Nuclear Information System (INIS)

    Maurer, M.

    1984-01-01

    Local symmetry (as evaluated from the electric field gradient tensor) and radial distribution functions (obtained by EXAFS measurement) are determined in a series of amorphous rare-earth base alloys. Local order is found to increase with the extent of heteroatomic interactions. Various magnetic phases (including ferromagnetic, spin-glass, reentrant spin-glass) occur for europium alloys with simple metals (Mg, Zn, Cd, Al, Au, ...). This variety reflects the sensitivity of exchange interactions to the presence of non-s conduction electrons. Asperomagnetic structures are established for the Dy alloys. The crystalline electric field interactions at the Dy 3+ ions are interpreted with the help of local symmetry data. Quadratic axial and non-axial crystal field terms are sufficient and necessary in order to account for the hyperfine and bulk experimental results [fr

  12. Use of alkali metal salts to prepare high purity single-walled carbon nanotube solutions and thin films

    Science.gov (United States)

    Ashour, Rakan F.

    Single-walled carbon nanotubes (SWCNTs) display interesting electronic and optical properties desired for many advanced thin film applications, such as transparent conductive electrodes or thin-film transistors. Large-scale production of SWCNTs generally results in polydispersed mixtures of nanotube structures. Since SWCNT electronic character (conducting or semiconducting nature) depends on the nanotube structure, application performance is being held back by this inability to discretely control SWCNT synthesis. Although a number of post-production techniques are able to separate SWCNTs based on electronic character, diameter, or chirality, most still suffer from the disadvantage of high costs of materials, equipment, or labor intensity to be relevant for large-scale production. On the other hand, chromatographic separation has emerged as a method that is compatible with large scale separation of metallic and semiconducting SWCNTs. In this work, SWCNTs, in an aqueous surfactant suspension of sodium dodecyl sulfate (SDS), are separated by their electronic character using a gel chromatography process. Metallic SWCNTs (m-SWCNTs) are collected as initial fractions since they show minimum interaction with the gel medium, whereas, semiconducting SWCNTs (sc- SWCNTs) remain adsorbed to the gel. The process of sc-SWCNT retention in the gel is found to be driven by the packing density of SDS around the SWCNTs. Through a series of separation experiments, it is shown that sc-SWCNTs can be eluted from the gel simply by disturbing the configuration of the SDS/SWCNT micellar structure. This is achieved by either introducing a solution containing a co-surfactant, such as sodium cholate (SC), or solutions of alkali metal ionic salts. Analysis of SWCNT suspensions by optical absorption provides insights into the effect of changing the metal ion (M+ = Li+, Na+, and K+) in the eluting solution. Salts with smaller metal ions (e.g. Li+) require higher concentrations to achieve

  13. A genetically modified tobacco mosaic virus that can produce gold nanoparticles from a metal salt precursor.

    Directory of Open Access Journals (Sweden)

    Andrew John Love

    2015-11-01

    Full Text Available We genetically modified tobacco mosaic virus (TMV to surface display a characterized peptide with potent metal ion binding and reducing capacity (MBP TMV, and demonstrate that unlike wild type (WT TMV, this construct can lead to the formation of discrete 10-40 nm gold nanoparticles when mixed with 3 mM potassium tetrachloroaurate. Using a variety of analytical physicochemical approaches it was found that these nanoparticles were crystalline in nature and stable. Given that the MBP TMV can produce metal nanomaterials in the absence of chemical reductants, it may have utility in the green production of metal nanomaterials.

  14. Electrolysis of metal oxides in MgCl2 based molten salts with an inert graphite anode.

    Science.gov (United States)

    Yuan, Yating; Li, Wei; Chen, Hualin; Wang, Zhiyong; Jin, Xianbo; Chen, George Z

    2016-08-15

    Electrolysis of solid metal oxides has been demonstrated in MgCl2-NaCl-KCl melt at 700 °C taking the electrolysis of Ta2O5 as an example. Both the cathodic and anodic processes have been investigated using cyclic voltammetry, and potentiostatic and constant voltage electrolysis, with the cathodic products analysed by XRD and SEM and the anodic products by GC. Fast electrolysis of Ta2O5 against a graphite anode has been realized at a cell voltage of 2 V, or a total overpotential of about 400 mV. The energy consumption was about 1 kW h kgTa(-1) with a nearly 100% Ta recovery. The cathodic product was nanometer Ta powder with sizes of about 50 nm. The main anodic product was Cl2 gas, together with about 1 mol% O2 gas and trace amounts of CO. The graphite anode was found to be an excellent inert anode. These results promise an environmentally-friendly and energy efficient method for metal extraction by electrolysis of metal oxides in MgCl2 based molten salts.

  15. Study of quantitative interactions of potato and corn starch granules with ions in diluted solutions of heavy metal salts.

    Science.gov (United States)

    Szymońska, Joanna; Molenda, Marcin; Wieczorek, Jerzy

    2015-12-10

    Interactions of potato and corn starch granules with ions in diluted solutions of silver, lead, copper or iron salts were investigated. It was shown experimentally that granules accumulated the cations in amounts depending on the granule structure and water content as well as a type of both metal and counter-ions present in solution. Potato starch retained almost three times more cations compared to corn starch what was proportional to the total phosphorous content in these starches. Quantity of milligrams of cations bound by 1g of starch was inversely correlated with the cation hydration. Ag(+), Pb(2+) and Cu(2+) were connected in stoichiometric amounts of moles to semicrystalline and amorphous parts of the granules. Fe(3+) ions were accumulated in higher than stoichiometric quantities mainly in granule amorphous regions. Metal ions penetrated into granules together with anions except nitrates which remained on surface of potato starch granules. Cations facilitated the starch thermal decomposition in accordance with values of their standard redox potentials. Nitrates supported this process only in the presence of base metal cations. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Capture and Solidification of Rare Earth Nuclide (Nd) in LiCl-KCl Eutectic Salt Using a Synthetic Inorganic Composite

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Na-Young; Eun, Hee-Chul; Park, Hwan-Seo; Ahn, Do-Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-06-15

    In this study, neodymium (Nd) nuclides in LiCl-KCl eutectic salts were captured and solidified using a synthetic inorganic composite (Li{sub 2}O-SiO{sub 2}-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}), a process that allows the selective capture of Nd and fabrication of a composite with Nd captured from waste, without additional additives or mixing. The Nd nuclides in the LiCl-KCl eutectic salt were mainly captured in the form of LiNdSiO{sub 4}, and it was confirmed that NdSiO{sub 3} can be formed in the composite with captured Nd when the content of Nd in the composite is increased. The capture efficiency was higher than about 98 wt%. It was thought that the salt recovered from the Nd capture test was a renewable form could be reused in the pyroprocessing of used nuclear fuel, because the composite has high chemical durability in a LiCl-KCl eutectic salt at 900 ℃. The composite captured Nd was fabricated into a homogeneous glass form and a stable ceramic form.

  17. Nitridomanganates of alkaline-earth metals. Synthesis, structure, and physical properties

    Energy Technology Data Exchange (ETDEWEB)

    Ovchinnikov, Alexander

    2016-12-02

    The main goal of the present work was the synthesis of alkaline-earth nitridomanganates (AE{sub x}Mn{sub y}N{sub z}) with extended anionic structures and the characterization of their electronic and magnetic properties. Up to now, only compounds with isolated nitridomanganate anions have been reported in the discussed ternary systems. A systematic exploratory synthesis, employing high-temperature treatment of AE nitrides and Mn under controlled N2 pressure, yielded more than ten new nitridomanganates. Their crystal structures contain anionic building blocks of different dimensionalities, ranging from isolated species to three-dimensional frameworks. In general, the formation of Mn-rich compositions was found to be driven by the emergence of Mn-Mn interactions, which creates a link between nitridometalates and transition-metal-rich binary nitrides. The obtained nitridomanganates display a plethora of interesting phenomena, such as large spin-orbit coupling, magnetic frustration, quenching of magnetism due to Mn-Mn interactions, and metal-insulator transition.

  18. The Importance of Rare-Earth Additions in Zr-Based AB2 Metal Hydride Alloys

    Directory of Open Access Journals (Sweden)

    Kwo-Hsiung Young

    2016-07-01

    Full Text Available Effects of substitutions of rare earth (RE elements (Y, La, Ce, and Nd to the Zr-based AB2 multi-phase metal hydride (MH alloys on the structure, gaseous phase hydrogen storage (H-storage, and electrochemical properties were studied and compared. Solubilities of the RE atoms in the main Laves phases (C14 and C15 are very low, and therefore the main contributions of the RE additives are through the formation of the RENi phase and change in TiNi phase abundance. Both the RENi and TiNi phases are found to facilitate the bulk diffusion of hydrogen but impede the surface reaction. The former is very effective in improving the activation behaviors. −40 °C performances of the Ce-doped alloys are slightly better than the Nd-doped alloys but not as good as those of the La-doped alloys, which gained the improvement through a different mechanism. While the improvement in ultra-low-temperature performance of the Ce-containing alloys can be associated with a larger amount of metallic Ni-clusters embedded in the surface oxide, the improvement in the La-containing alloys originates from the clean alloy/oxide interface as shown in an earlier transmission electron microscopy study. Overall, the substitution of 1 at% Ce to partially replace Zr gives the best electrochemical performances (capacity, rate, and activation and is recommended for all the AB2 MH alloys for electrochemical applications.

  19. In situ formation of coal gasification catalysts from low cost alkali metal salts

    Science.gov (United States)

    Wood, Bernard J.; Brittain, Robert D.; Sancier, Kenneth M.

    1985-01-01

    A carbonaceous material, such as crushed coal, is admixed or impregnated with an inexpensive alkali metal compound, such as sodium chloride, and then pretreated with a stream containing steam at a temperature of 350.degree. to 650.degree. C. to enhance the catalytic activity of the mixture in a subsequent gasification of the mixture. The treatment may result in the transformation of the alkali metal compound into another, more catalytically active, form.

  20. Spectroscopic Characterization of Omeprazole and Its Salts

    Directory of Open Access Journals (Sweden)

    Tomislav Vrbanec

    2017-01-01

    Full Text Available During drug development, it is important to have a suitable crystalline form of the active pharmaceutical ingredient (API. Mostly, the basic options originate in the form of free base, acid, or salt. Substances that are stable only within a certain pH range are a challenge for the formulation. For the prazoles, which are known to be sensitive to degradation in an acid environment, the formulation is stabilized with alkaline additives or with the application of API formulated as basic salts. Therefore, preparation and characterization of basic salts are needed to monitor any possible salinization of free molecules. We synthesized salts of omeprazole from the group of alkali metals (Li, Na, and K and alkaline earth metals (Mg, Ca. The purpose of the presented work is to demonstrate the applicability of vibrational spectroscopy to discriminate between the OMP and OMP-salt molecules. For this reason, the physicochemical properties of 5 salts were probed using infrared and Raman spectroscopy, NMR, TG, DSC, and theoretical calculation of vibrational frequencies. We found out that vibrational spectroscopy serves as an applicable spectroscopic tool which enables an accurate, quick, and nondestructive way to determine the characteristic of OMP and its salts.

  1. Partition of actinides and fission products between metal and molten salt phases: Theory, measurement, and application to IFR pyroprocess development

    International Nuclear Information System (INIS)

    Ackerman, J.P.; Johnson, T.R.

    1993-01-01

    The chemical basis of Integral Fast Reactor fuel reprocessing (pyroprocessing) is partition of fuel, cladding, and fission product elements between molten LiCl-KCl and either a solid metal phase or a liquid cadmium phase. The partition reactions are described herein, and the thermodynamic basis for predicting distributions of actinides and fission products in the pyroprocess is discussed. The critical role of metal-phase activity coefficients, especially those of rare earth and the transuranic elements, is described. Measured separation factors, which are analogous to equilibrium constants but which involve concentrations rather than activities, are presented. The uses of thermodynamic calculations in process development are described, as are computer codes developed for calculating material flows and phase compositions in pyroprocessing

  2. Partition of actinides and fission products between metal and molten salt phases: Theory, measurement, and application to IFR pyroprocess development

    Energy Technology Data Exchange (ETDEWEB)

    Ackerman, J.P.; Johnson, T.R.

    1993-10-01

    The chemical basis of Integral Fast Reactor fuel reprocessing (pyroprocessing) is partition of fuel, cladding, and fission product elements between molten LiCl-KCl and either a solid metal phase or a liquid cadmium phase. The partition reactions are described herein, and the thermodynamic basis for predicting distributions of actinides and fission products in the pyroprocess is discussed. The critical role of metal-phase activity coefficients, especially those of rare earth and the transuranic elements, is described. Measured separation factors, which are analogous to equilibrium constants but which involve concentrations rather than activities, are presented. The uses of thermodynamic calculations in process development are described, as are computer codes developed for calculating material flows and phase compositions in pyroprocessing.

  3. Thermal stability of the anionic sigma complexes of 2,4,6-trinitroanisole with the methylates of the alkaline-earth metals

    Energy Technology Data Exchange (ETDEWEB)

    Glaz, A.I.; Soldatova, T.A.; Golopolosova, T.V.; Gitis, S.S.

    1987-09-10

    The study of the stability of the 1,1-dimethoxy-2,4,6-trinitrocyclohexadienates of the alkali metals when they are heated in air showed that their temperature of decomposition and the heat effect of the process are dependent on the nature of the cation. Our study centered on the thermal decomposition of the products resulting from the addition of the methylates of calcium, strontium, and barium to 2,4,6-trinitroanisole. For a quantitative assessment of the process we used the combined methods of differential-thermal analysis and differential thermogravimetry. The anionic sigma-complexes of 2,4,6-trinitroanisole with the methylates of the alkaline-earth metals decompose on heating into the corresponding picrates; at the same time, when one passes from the calcium slat to the strontium and barium salts the decomposition temperature and the heat effect of the process show a drop which is linked to the structure both of the complexes and of the picrates forming therefrom.

  4. Stress Corrosion Cracking Susceptibility of 304L Substrate and 308L Weld Metal Exposed to a Salt Spray.

    Science.gov (United States)

    Hsu, Chia-Hao; Chen, Tai-Cheng; Huang, Rong-Tan; Tsay, Leu-Wen

    2017-02-15

    304 stainless steels (SS) were considered as the materials for a dry storage canister. In this study, ER (Electrode Rod) 308L was utilized as the filler metal for the groove and overlay welds of a 304L stainless steel substrate, which was prepared via a gas tungsten arc-welding process in multiple passes. The electron backscatter diffraction (EBSD) map was used to identify the inherent microstructures in distinct specimens. U-bend and weight-loss tests were conducted by testing the 304L substrates and welds in a salt spray containing 5 wt % NaCl at 80 °C to evaluate their susceptibility to stress corrosion cracking (SCC). Generally, the weight loss of the ER 308L deposit was higher than that of the 304L substrate in a salt spray in the same sample-prepared condition. The dissolution of the skeletal structure in the fusion zone (FZ) was responsible for a greater weight loss of the 308L deposit, especially for the cold-rolled and sensitized specimen. Cold rolling was detrimental and sensitization after cold rolling was very harmful to the SCC resistance of the 304L substrate and 308L deposit. Overall, the SCC susceptibility of each specimen was correlated with its weight loss in each group.

  5. Stress Corrosion Cracking Susceptibility of 304L Substrate and 308L Weld Metal Exposed to a Salt Spray

    Directory of Open Access Journals (Sweden)

    Chia-Hao Hsu

    2017-02-01

    Full Text Available 304 stainless steels (SS were considered as the materials for a dry storage canister. In this study, ER (Electrode Rod 308L was utilized as the filler metal for the groove and overlay welds of a 304L stainless steel substrate, which was prepared via a gas tungsten arc-welding process in multiple passes. The electron backscatter diffraction (EBSD map was used to identify the inherent microstructures in distinct specimens. U-bend and weight-loss tests were conducted by testing the 304L substrates and welds in a salt spray containing 5 wt % NaCl at 80 °C to evaluate their susceptibility to stress corrosion cracking (SCC. Generally, the weight loss of the ER 308L deposit was higher than that of the 304L substrate in a salt spray in the same sample-prepared condition. The dissolution of the skeletal structure in the fusion zone (FZ was responsible for a greater weight loss of the 308L deposit, especially for the cold-rolled and sensitized specimen. Cold rolling was detrimental and sensitization after cold rolling was very harmful to the SCC resistance of the 304L substrate and 308L deposit. Overall, the SCC susceptibility of each specimen was correlated with its weight loss in each group.

  6. Influence of irradiated chitosan on rice plants growing in hydroponic medium contaminated with salt and heavy metals

    Energy Technology Data Exchange (ETDEWEB)

    Lam, N.D.; Diep, T.B. [Institute for Nuclear Science and Technique-VAEC, Nghiado, Cau giay, Hanoi (Viet Nam); Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2000-03-01

    Effect of chitosan and radiation-degraded chitosan on rice seedlings of a Vietnam's original variety was investigated. Potential of irradiated chitosan in plant tolerance for several stress factors (salt, zinc, and vanadium) also was studied as well. Chitosan represented in hydroponic medium clearly inhibited the growth of rice seedlings at concentrations arranging from 50 ppm. Radiation processing of chitosan with dose higher than 100 kGy reduced toxicity of chitosan and the efficacy was of dose proportion. Rice plant of 203 origin was almost normally grown in hydroponic solution containing chitosan that has been irradiated with dose of 150 and 200 kGy. Irradiated chitosan increased plant resistance to environmental stress caused by vanadium (V); thereby the seedlings could be recovered completely, even gained in biomass. This effect was not appeared when applied chitosan to rice in media contaminated by zinc (Zn) and salt (NaCl). The selectness of irradiated chitosan on various stress factors partly clarified the assistant action of chitosan in the vanadium intoxication because chelating with metal ions could not be evaluated as main mechanism. (author)

  7. Influence of irradiated chitosan on rice plants growing in hydroponic medium contaminated with salt and heavy metals

    International Nuclear Information System (INIS)

    Lam, N.D.; Diep, T.B.; Kume, Tamikazu

    2000-01-01

    Effect of chitosan and radiation-degraded chitosan on rice seedlings of a Vietnam's original variety was investigated. Potential of irradiated chitosan in plant tolerance for several stress factors (salt, zinc, and vanadium) also was studied as well. Chitosan represented in hydroponic medium clearly inhibited the growth of rice seedlings at concentrations arranging from 50 ppm. Radiation processing of chitosan with dose higher than 100 kGy reduced toxicity of chitosan and the efficacy was of dose proportion. Rice plant of 203 origin was almost normally grown in hydroponic solution containing chitosan that has been irradiated with dose of 150 and 200 kGy. Irradiated chitosan increased plant resistance to environmental stress caused by vanadium (V); thereby the seedlings could be recovered completely, even gained in biomass. This effect was not appeared when applied chitosan to rice in media contaminated by zinc (Zn) and salt (NaCl). The selectness of irradiated chitosan on various stress factors partly clarified the assistant action of chitosan in the vanadium intoxication because chelating with metal ions could not be evaluated as main mechanism. (author)

  8. Crystal fields in Sc, Y, and the heavy-rare-earth metals Tb, Dy, Ho, Er, Tm, and Lu

    DEFF Research Database (Denmark)

    Touborg, P.

    1977-01-01

    -field parameters for all these 15 alloy systems deduced. The consistency of the parameters was confirmed by a variety of magnetic measurements, including neutron spectroscopy. Crystal-field parameters have also been derived for the ions in pure magnetic rare-earth metals and their alloys using the results......—with the inaccuracies somewhat increased—are expected to be representative also for the magnetic rare-earth metals. For rare-earth ions in the Sc host the values B40 / β=9.9±1.9 K, B60 / γ=19.8±1.5 K, and B66 / γ=(9.4±0.9)β60 / γ were deduced. B20 / α is a host-sensitive parameter which has the average values of -102.......7, -53.4, and 29.5 K for rare-earth ions in Y, Lu, and Sc, respectively. There is also evidence that this parameter varies with the solute. B20 / α for ions in the pure magnetic rare-earth metals and their alloys shows a linear variation with c / a ratio characteristic of each ion. The results indicate...

  9. Test of electrodialytic upgrading of MSWI APC residue in pilot scale: focus on reduced metal and salt leaching

    DEFF Research Database (Denmark)

    Kirkelund, Gunvor Marie; Jensen, Pernille Erland; Villumsen, Arne

    2010-01-01

    In this study a pilot plant for electrodialytic treatment of municipal solid waste incineration (MSWI) air pollution control (APC) residue was tested and proposed as a treatment method which can lead to reuse of this otherwise hazardous waste. The pilot plant was developed based on a design...... that is adapted from conventional electrodialysis, e.g. used in desalination of solutions. The APC residue was treated in a suspension (8 kg APC residue and 80 L tap water) and circulated through an electrodialytic (ED) stack consisting of 50 cell pairs separated by ion exchange membranes. A direct current...... was applied to the ED stack for removal of heavy metals (As, Ba, Cd, Cr, Cu, Mn, Ni, Pb, Zn) and salts (Cl, Na, SO4) from the APC residue suspension. Different tank designs for mixing the APC residue suspension were tested as well as changing experimental conditions. A part of the raw experimental APC residue...

  10. Achieving Amphibious Superprotonic Conductivity in a CuI Metal-Organic Framework by Strategic Pyrazinium Salt Impregnation.

    Science.gov (United States)

    Khatua, Sajal; Bar, Arun Kumar; Sheikh, Javeed Ahmad; Clearfield, Abraham; Konar, Sanjit

    2018-01-19

    Treatment of a pyrazine (pz)-impregnated Cu I metal-organic framework (MOF) ([1⊃pz]) with HCl vapor renders an interstitial pyrazinium chloride salt-hybridized MOF ([1⊃pz⋅6 HCl]) that exhibits proton conductivity over 10 -2  S cm -1 both in anhydrous and under humid conditions. Framework [1⊃pz⋅6 HCl] features the highest anhydrous proton conductivity among the lesser-known examples of MOF-based materials exhibiting proton conductivity under both anhydrous and humid conditions. Moreover, [1⊃pz] and corresponding pyrazinium sulfate- and pyrazinium phosphate-hybridized MOFs also exhibit superprotonic conductivity over 10 -2  S cm -1 under humid conditions. The impregnated pyrazinium ions play a crucial role in protonic conductivity, which occurs through a Grotthuss mechanism. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Recyclable Earth-Abundant Metal Nanoparticle Catalysts for Selective Transfer Hydrogenation of Levulinic Acid to Produce γ-Valerolactone.

    Science.gov (United States)

    Gowda, Ravikumar R; Chen, Eugene Y-X

    2016-01-01

    Nanoparticles (NPs) derived from earth-abundant metal(0) carbonyls catalyze conversion of bio-derived levulinic acid into γ-valerolactone in up to 93% isolated yield. This sustainable and green route uses non-precious metal catalysts and can be performed in aqueous or ethanol solution without using hydrogen gas as the hydrogen source. Generation of metal NPs using microwave irradiation greatly enhances the rate of the conversion, enables the use of ethanol as both solvent and hydrogen source without forming the undesired ethyl levulinate, and affords recyclable polymer-stabilized NPs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. Theoretical Study of pKaValues for Trivalent Rare-Earth Metal Cations in Aqueous Solution.

    Science.gov (United States)

    Yu, Donghai; Du, Ruobing; Xiao, Ji-Chang; Xu, Shengming; Rong, Chunying; Liu, Shubin

    2018-01-18

    Molecular acidity of trivalent rare-earth metal cations in aqueous solution is an important factor dedicated to the efficiency of their extraction and separation processes. In this work, the aqueous acidity of these metal ions has been quantitatively investigated using a few theoretical approaches. Our computational results expressed in terms of pK a values agree well with the tetrad effect of trivalent rare-earth ions extensively reported in the extraction and separation of these elements. Strong linear relationships have been observed between the acidity and quantum electronic descriptors such as the molecular electrostatic potential on the acidic nucleus and the sum of the valence natural atomic orbitals energies of the dissociating proton. Making use of the predicted pK a values, we have also predicted the major ionic forms of these species in the aqueous environment with different pH values, which can be employed to rationalize the behavior difference of different rare-earth metal cations during the extraction process. Our present results should provide needed insights not only for the qualitatively understanding about the extraction and separation between yttrium and lanthanide elements but also for the prediction of novel and more efficient rare-earth metal extractants in the future.

  13. A rare earth-based metal-organic framework for moisture removal and control in confined spaces

    KAUST Repository

    Eddaoudi, Mohamed

    2017-04-13

    A method for preparing a metal-organic framework (MOF) comprising contacting one or more of a rare earth metal ion component with one or more of a tetratopic ligand component, sufficient to form a rare earth-based MOF for controlling moisture in an environment. A method of moisture control in an environment comprising adsorbing and/or desorbing water vapor in an environment using a MOF, the MOF including one or more of a rare earth metal ion component and one or more of a tetratopic ligand component. A method of controlling moisture in an environment comprising sensing the relative humidity in the environment comprising a MOF; and adsorbing water vapor on the MOF if the relative humidity is above a first level, sufficient to control moisture in an environment. The examples relate to a MOF created from 1,2,4,5-Tetrakis(4-carboxyphenyl )benzene (BTEB) as tetratopic ligand, 2-fluorobenzoic acid and Y(NO3)3, Tb(NO3)3 and Yb(NO3)3 as rare earth metals.

  14. Selective oxidation of methanol to hydrogen over gold catalysts promoted by alkaline-earth-metal and lanthanum oxides

    NARCIS (Netherlands)

    Hereijgers, B.P.C.; Weckhuysen, B.M.

    2009-01-01

    A series of alumina-supported gold catalysts was investigated for the CO-free production of hydrogen by partial oxidation of methanol. The addition of alkaline-earth metal oxide promoters resulted in a significant improvement of the catalytic performance. The methanol conversion was ca. 85 % with

  15. Metal sulfide and rare-earth phosphate nanostructures and methods of making same

    Science.gov (United States)

    Wong, Stanislaus; Zhang, Fen

    2014-05-13

    The present invention provides a method of producing a crystalline metal sulfide nanostructure. The metal is a transitional metal or a Group IV metal. In the method, a porous membrane is placed between a metal precursor solution and a sulfur precursor solution. The metal cations of the metal precursor solution and sulfur ions of the sulfur precursor solution react, thereby producing a crystalline metal sulfide nanostructure.

  16. Small cell experiments for electrolytic reduction of uranium oxides to uranium metal using fluoride salts

    International Nuclear Information System (INIS)

    Haas, P.A.; Adcock, P.W.; Coroneos, A.C.; Hendrix, D.E.

    1994-01-01

    Electrolytic reduction of uranium oxide was proposed for the preparation of uranium metal feed for the atomic vapor laser isotope separation (AVLIS) process. A laboratory cell of 25-cm ID was operated to obtain additional information in areas important to design and operation of a pilot plant cell. Reproducible test results and useful operating and control procedures were demonstrated. About 20 kg of uranium metal of acceptable purity were prepared. A good supply of dissolved UO 2 feed at the anode is the most important controlling requirement for efficient cell operation. A large fraction of the cell current is nonproductive in that it does not produce a metal product nor consume carbon anodes. All useful test conditions gave some reduction of UF 4 to produce CF 4 in addition to the reduction of UO 2 , but the fraction of metal from the reduction of UF 4 can be decreased by increasing the concentration of dissolved UO 2 . Operation of large continuous cells would probably be limited to current efficiencies of less than 60 pct, and more than 20 pct of the metal would result from the reduction of UF 4

  17. Immobilization of IFR salt wastes in mortar

    International Nuclear Information System (INIS)

    Fisher, D.F.; Johnson, T.R.

    1988-01-01

    Portland cement-base mortars are being considered for immobilizing chloride salt wastes from the fuel cycle of an integral fast reactor (IFR). The IFR is a sodium-cooled fast reactor with metal fuel. It has a close-coupled fuel cycle in which fission products are separated from the actinides in an electrochemical cell operating at 500 degrees C. This cell has a cadmium anode and a liquid salt electrolyte. The salt will be a low-melting mixture of alkaline and alkaline earth chlorides. This paper discusses one method being considered for immobilizing this treated salt, to disperse it in a portland cement-base motar, which would then be sealed in corrosion-resistant containers. For this application, the grout must be sufficiently fluid that it can be pumped into canisters where it will solidify into a strong, leach-resistant material

  18. Polarization and mass transfer during the electrolysis of molten salts with liquid metallic electrodes

    Science.gov (United States)

    Mikhalev, Yu. G.

    2014-08-01

    Calculations are used to show that the fraction of the overvoltage of the stage of discharge-ionization can be significant in the total overvoltage during the polarization of liquid metallic electrodes in molten chlorides depleted of electrochemically active particles (depending on the type of the dissipative structures that appear near the electrode/electrolyte interface). This finding is taken into account to obtain criterion equations to describe the mass-transfer rate as a function of the physicochemical properties of the electrolyte and the metal electrode.

  19. Fundamental Study on a Distillation Separation of a LiCl-KCl Eutectic Salt from Rare Earth Precipitates

    International Nuclear Information System (INIS)

    Yang, Hee Chul; Eun, Hee Chul; Kim, In Tae

    2010-01-01

    The distillation rate on LiCl-KCl eutectic salt under different vacuums from 0.5-50 mmHg was first investigated by using both a non-isothermal and a isothermal thermogravimetric (TG) analysis. Based on the non-isothermal TG data, distillation rate equations as a function of the temperature could be derived. Calculated flux by these model flux equations was in agreement with the distillation rate obtained from isothermal TG analysis. A distillation rate of 10 -4 -10 -5 mole cm -2 sec -1 is obtainable at temperatures less than 1300 K and vacuums of 0.5-50 mmHg. About a 99% salt distillation efficiency was obtained after an hour at a temperature above 1150 K under 50 mmHg in a small scale distillation test system. An increase in the vaporizing surface area is relatively effective for removing residual salt in the remaining particles, when compared to that for the vaporizing time. Over 99.95% of total distillation efficiency was obtained for a 1-h distillation operation by increasing the inner surface area from 4.52 cm 2 to 12.56 cm 2 .

  20. Oxidation catalysts on alkaline earth supports

    Science.gov (United States)

    Mohajeri, Nahid

    2017-03-21

    An oxidation catalyst includes a support including particles of an alkaline earth salt, and first particles including a palladium compound on the support. The oxidation catalyst can also include precious metal group (PMG) metal particles in addition to the first particles intermixed together on the support. A gas permeable polymer that provides a continuous phase can completely encapsulate the particles and the support. The oxidation catalyst may be used as a gas sensor, where the first particles are chemochromic particles.

  1. Salt waste treatment from a LiCl-KCl based pyrochemical spent fuel treatment process

    International Nuclear Information System (INIS)

    Harrison, Mike T.; Simms, Howard; Jackson, Angela; Lewin, Robert G.

    2005-01-01

    Spent nuclear fuel may be treated using molten salt electrochemical techniques to separate fission products and actinide metals. Salt waste arising from the electrorefining process contains alkali metals, alkaline-earth and rare earth fission products, along with residual actinides. The removal of fission product elements has been investigated using zeolite ion exchange and phosphate precipitation, which allow the salt electrolyte to be recycled back into the main electrorefining vessel. Recycling the salt minimizes the volume of high level waste (HLW) generated and yields the fission products in a form more amenable to immobilization in a final disposal matrix. Several sets of experiments have been completed, all of which have significant implications for the use of these techniques on an industrial scale, as well as their ability to clean up the salt, and potentially produce robust and durable waste forms. (author)

  2. Salt-Templated Synthesis of 2D Metallic MoN and Other Nitrides.

    Science.gov (United States)

    Xiao, Xu; Yu, Huimin; Jin, Huanyu; Wu, Menghao; Fang, Yunsheng; Sun, Jiyu; Hu, Zhimi; Li, Tianqi; Wu, Jiabin; Huang, Liang; Gogotsi, Yury; Zhou, Jun

    2017-02-28

    Two-dimensional (2D) transition-metal nitrides just recently entered the research arena, but already offer a potential for high-rate energy storage, which is needed for portable/wearable electronics and many other applications. However, a lack of efficient and high-yield synthesis methods for 2D metal nitrides has been a major bottleneck for the manufacturing of those potentially very important materials, and only MoN, Ti 4 N 3 , and GaN have been reported so far. Here we report a scalable method that uses reduction of 2D hexagonal oxides in ammonia to produce 2D nitrides, such as MoN. MoN nanosheets with subnanometer thickness have been studied in depth. Both theoretical calculation and experiments demonstrate the metallic nature of 2D MoN. The hydrophilic restacked 2D MoN film exhibits a very high volumetric capacitance of 928 F cm -3 in sulfuric acid electrolyte with an excellent rate performance. We expect that the synthesis of metallic 2D MoN and two other nitrides (W 2 N and V 2 N) demonstrated here will provide an efficient way to expand the family of 2D materials and add many members with attractive properties.

  3. Modeling of heavy metal salt solubility using the Extended UNIQUAC model

    DEFF Research Database (Denmark)

    Iliuta, Maria Cornelia; Thomsen, Kaj; Rasmussen, Peter

    2002-01-01

    Solid-liquid equilibria in complex aqueous systems involving a heavy metal cation (Mn2+, Fe2+, Co2+, Ni2+, Cu2+, or Zn2+) and one or more ions for which Extended UNIQUAC parameters have been published previously are modeled using the Extended UNIQUAC model. Model parameters are determined...

  4. LiCl-LiI molten salt electrolyte with bismuth-lead positive electrode for liquid metal battery

    Science.gov (United States)

    Kim, Junsoo; Shin, Donghyeok; Jung, Youngjae; Hwang, Soo Min; Song, Taeseup; Kim, Youngsik; Paik, Ungyu

    2018-02-01

    Liquid metal batteries (LMBs) are attractive energy storage device for large-scale energy storage system (ESS) due to the simple cell configuration and their high rate capability. The high operation temperature caused by high melting temperature of both the molten salt electrolyte and metal electrodes can induce the critical issues related to the maintenance cost and degradation of electrochemical properties resulting from the thermal corrosion of materials. Here, we report a new chemistry of LiCl-LiI electrolyte and Bi-Pb positive electrode to lower the operation temperature of Li-based LMBs and achieve the long-term stability. The cell (Li|LiCl-LiI|Bi-Pb) is operated at 410 °C by employing the LiCl-LiI (LiCl:LiI = 36:64 mol %) electrolyte and Bi-Pb alloy (Bi:Pb = 55.5:44.5 mol %) positive electrode. The cell shows excellent capacity retention (86.5%) and high Coulombic efficiencies over 99.3% at a high current density of 52 mA cm-2 during 1000th cycles.

  5. Inhibition studies of soybean (Glycine max) urease with heavy metals, sodium salts of mineral acids, boric acid, and boronic acids.

    Science.gov (United States)

    Kumar, Sandeep; Kayastha, Arvind M

    2010-10-01

    Various inhibitors were tested for their inhibitory effects on soybean urease. The K(i) values for boric acid, 4-bromophenylboronic acid, butylboronic acid, and phenylboronic acid were 0.20 +/- 0.05 mM, 0.22 +/- 0.04 mM, 1.50 +/- 0.10 mM, and 2.00 +/- 0.11 mM, respectively. The inhibition was competitive type with boric acid and boronic acids. Heavy metal ions including Ag(+), Hg(2+), and Cu(2+) showed strong inhibition on soybean urease, with the silver ion being a potent inhibitor (IC(50) = 2.3 x 10(-8) mM). Time-dependent inhibition studies exhibited biphasic kinetics with all heavy metal ions. Furthermore, inhibition studies with sodium salts of mineral acids (NaF, NaCl, NaNO(3), and Na(2)SO(4)) showed that only F(-) inhibited soybean urease significantly (IC(50) = 2.9 mM). Competitive type of inhibition was observed for this anion with a K(i) value of 1.30 mM.

  6. Crystallographic and spectroscopic investigations on nine metal-rare-earth silicates with the apatite structure type

    International Nuclear Information System (INIS)

    Wierzbicka-Wieczorek, Maria; Goeckeritz, Martin; Kolitsch, Uwe; Lenz, Christoph; Giester, Gerald

    2015-01-01

    Nine silicates with the apatite structure type (space group P6 3 /m) containing both rare-earth elements (REEs: Pr, Nd, Sm, Tb, Ho and Er) and various metals (K, Sr, Ba and Cd) were synthesised by high-temperature flux-growth techniques and characterised by single-crystal X-ray diffraction, scanning electron microscopy, Raman spectroscopy and laser-induced photoluminescence spectroscopy. In all of the compounds, the 6h Wyckoff position is predominantly or solely occupied by REE 3+ cations, whereas the cations shows a mixed occupancy at the larger, nine-coordinate 4f site with 55-75 % of REE 3+ cations and 45-25 % of other metal cations. The O4 (''free'' oxygen) site is fully occupied by O 2- anions, except for a Ba-Pr member with full occupancy by F - anions. The refined formulas are Cd 2 Er 8 (SiO 4 ) 6 O 2 , Cd 2 Tb 8 (SiO 4 ) 6 O 2 , KHo 9 (SiO 4 ) 6 O 2 , KTb 9 (SiO 4 ) 6 O 2 , KSm 9 (SiO 4 ) 6 O 2 , Sr 2 Nd 8 (SiO 4 ) 6 O 2 , Ba 2 Nd 8 (SiO 4 ) 6 O 2 , Ba 2 Sm 8 (SiO 4 ) 6 O 2 and Ba 4 Pr 6 (SiO 4 ) 6 F 2 . Changes in the metaprism twist angle (φ) and correlations between the unit-cell parameters, average cationic radii (of M + /M 2+ -REE 3+ pairs) and the chemistry of both the synthesised M + /M 2+ -REE 3+ silicate apatites and those reported previously are evaluated. Photoluminescence measurements of undoped samples yielded emission bands in the visible region from green to red; therefore, these compounds are potential candidates for luminescent materials. (Copyright copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Solvent and stabilizer free growth of Ag and Pd nanoparticles using metallic salts/cyclotriphosphazenes mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Díaz Valenzuela, C. [Departamento de Química, Facultad de Química, Universidad de Chile, La Palmeras 3425, Nuñoa, Casilla 653, Santiago de Chile (Chile); Valenzuela, M.L., E-mail: mlvalenzuela@unab.cl [Universidad Andres Bello, Departamento de Ciencias Química, Facultad de Ciencias Exactas, Av. Republica 275, Santiago (Chile); Caceres, S.; Diaz, R. [Departamento de Química, Facultad de Química, Universidad de Chile, La Palmeras 3425, Nuñoa, Casilla 653, Santiago de Chile (Chile); O' Dwyer, C. [Applied Nanoscience Group, Department of Chemistry, University College Cork, Cork (Ireland); Micro and Nanoelectronics Centre, Tyndall National Institute, Lee Maltings, Cork (Ireland)

    2013-12-16

    Cyclotriphosphazene is used as a sacrificial solid-state template to synthesize a range of Ag and Pd nanoparticles with diverse geometries by thermal treatment using MLn/N{sub 3}P{sub 3}(O{sub 2}C{sub 12}H{sub 8}){sub 3} mixtures. The Pd and Ag nanoparticles are synthesized by solid-state pyrolysis of AgPPh{sub 3}[CF{sub 3}SO{sub 3}]/N{sub 3}P{sub 3}(O{sub 2}C{sub 12}H{sub 8}){sub 3} and PdCl{sub 2}/N{sub 3}P{sub 3}(O{sub 2}C{sub 12}H{sub 8}){sub 3} mixtures with molar relationships of 1:1, 1:5 and 1:10 respectively, in air and at 800 °C. The morphology of the as-prepared nanoparticles is found to depend on the molar ratio of the precursor mixture, the preparation method and of the nature of the metal. Ag and Pd, microcrystals were thermally grown on Si from the respective 1:1 precursors while that metal foams were grown from 1:5 ratios precursors on SiO{sub 2} wafers. High resolution transmission electron microscopy investigations reveal in most cases small crystals of Pd. HRSTEM measurements indicate that the formation of the Pd and Ag nanoparticles occurs through a phase demixing and dewetting mechanism. This approach has potential to be a useful and facile method to prepare metallic nanoparticles without requiring solutions or surfactants for application in electronic, catalytic and sensor materials and devices. - Highlights: • Pyrolysis MLn/N{sub 3}P{sub 3}(O{sub 2}C{sub 12}H{sub 8}){sub 3} mixtures under air, give Pd and Ag nanoparticles. • AgPPh{sub 3}[CF{sub 3}SO{sub 3}] and PdCl{sub 2} in molar ratios 1:1 and 1:5 were used. • Metal foams were obtained from 1:5 ratios when deposited on SiO{sub 2.} • Using crucible supporting in 1:1 metal/trimer <2 nm Pd nanoparticles were obtained. • The probable mechanism involves a dewetting, nucleation and ripening crystallization.

  8. Alkaline-earth metal (Mg) polynitrides at high pressure as possible high-energy materials.

    Science.gov (United States)

    Wei, Shuli; Li, Da; Liu, Zhao; Li, Xin; Tian, Fubo; Duan, Defang; Liu, Bingbing; Cui, Tian

    2017-03-29

    The high-pressure structural evolutionary behaviors of magnesium polynitrides were studied up to 100 GPa using first-principles calculations. Using the unbiased structure searching method, five stable chemical stoichiometries of magnesium polynitrides (MgN, Mg 2 N 3 , MgN 2 , MgN 3 , and MgN 4 ) were theoretically predicted at high pressures. The predicted MgN x compounds contain a rich variety of polynitrogen forms ranging from charged molecules (one-dimensional bent molecules N 3 , planar triangle N 4 to benzene-like rings N 6 ) to extended polymeric chains (N ∞ ). To the best of our knowledge, this is the first time that stable bent molecules N 3 , planar triangle N 4 , and polymeric chains (N ∞ ) were predicted in alkaline-earth metal polynitrides. The decomposition of P1[combining macron]-MgN 3 and P1[combining macron]-MgN 4 are expected to be highly exothermic, releasing an energy of approximately 2.83 kJ g -1 and 2.01 kJ g -1 , respectively. Furthermore, P1[combining macron]-MgN 4 can be synthesized at several GPa. The results of the present study suggest that it is possible to obtain energetic polynitrogen in main-group nitrides under high pressure.

  9. A Complete Design of a Rare Earth Metal-Free Permanent Magnet Generator

    Directory of Open Access Journals (Sweden)

    Petter Eklund

    2014-05-01

    Full Text Available The price of rare-earth metals used in neodymium-iron-boron (NdFeB permanent magnets (PMs has fluctuated greatly recently. Replacing the NdFeB PMs with more abundant ferrite PMs will avoid the cost insecurity and insecurity of supply. Ferrite PMs have lower performance than NdFeB PMs and for similar performance more PM material has to be used, requiring more support structure. Flux concentration is also necessary, for example, by a spoke-type rotor. In this paper the rotor of a 12 kW NdFeB PM generator was redesigned to use ferrite PMs, reusing the existing stator and experimental setup. Finite element simulations were used to calculate both electromagnetic and mechanical properties of the design. Focus was on mechanical design and feasibility of construction. The result was a design of a ferrite PM rotor to be used with the old stator with some small changes to the generator support structure. The new generator has the same output power at a slightly lower voltage level. It was concluded that it is possible to use the same stator with either a NdFeB PM rotor or a ferrite PM rotor. A ferrite PM generator might require a larger diameter than a NdFeB generator to generate the same voltage.

  10. Biodiesel production using alkali earth metal oxides catalysts synthesized by sol-gel method

    Directory of Open Access Journals (Sweden)

    Majid Mohadesi

    2014-03-01

    Full Text Available Biodiesel fuel is considered as an alternative to diesel fuel. This fuel is produced through transesterification reactions of vegetable oils or animal fat by alcohols in the presence of different catalysts. Recent studies on this process have shown that, basic heterogeneous catalysts have a higher performance than other catalysts. In this study different alkali earth metal oxides (CaO, MgO and BaO doped SiO2 were used as catalyst for the biodiesel production process. These catalysts were synthesis by using the sol-gel method. A transesterification reaction was studied after 8h by mixing corn oil, methanol (methanol to oil molar ratio of 16:1, and 6 wt. % catalyst (based on oil at 60oC and 600rpm. Catalyst loading was studied for different catalysts ranging in amounts from 40, 60 to 80%. The purity and yield of the produced biodiesel for 60% CaO/SiO2 was higher than other catalysts and at 97.3% and 82.1%, respectively.

  11. Threefold symmetric magnetic two-ion coupling in hcp rare-earth metals

    International Nuclear Information System (INIS)

    Jensen, J.

    1997-01-01

    The heavy rare earths crystallize in the hcp structure. Most of magnetic couplings between two ions in these metals are independent of the two different orientations of the hexagonal layers. However, trigonal anisotropy terms may occur, reflecting that c-axis is only threefold axis. In the presence of a trigonal coupling the symmetry is reduced, and the double-zone representation in the c-direction ceases to be valid. The strong interaction between the transverse optical phonons and the acoustic spin waves propagating in the c-direction of Yb detected more than twenty years ago, was the first example of a trigonal coupling found in these systems. A few years ago a careful neutron-diffraction study of the c-axis modulated magnetic structures in Er showed the presence of higher harmonics at positions along the c-axis translated by odd multiple of 2φ/c. This indicates distortions of the structures due to trigonal couplings, and the same characteristic phenomenon has now been also observed in Ho. Additionally, mean field calculations show that a trigonal coupling in Ho is required, in order to explain the increase in the commensurable effects observed for the 8 and 10 layered periodic structures, when a field is applied along the c-axis. (author)

  12. Alkaline earth metal and samarium co-doped ceria as efficient electrolytes

    Science.gov (United States)

    Ali, Amjad; Raza, Rizwan; Kaleem Ullah, M.; Rafique, Asia; Wang, Baoyuan; Zhu, Bin

    2018-01-01

    Co-doped ceramic electrolytes M0.1Sm0.1Ce0.8O2-δ (M = Ba, Ca, Mg, and Sr) were synthesized via co-precipitation. The focus of this study was to highlight the effects of alkaline earth metals in doped ceria on the microstructure, densification, conductivity, and performance. The ionic conductivity comparisons of prepared electrolytes in the air atmosphere were studied. It has been observed that Ca0.1Sm0.1Ce0.8O2-δ shows the highest conductivity of 0.124 Scm-1 at 650 °C and a lower activation energy of 0.48 eV. The cell shows a maximum power density of 630 mW cm-2 at 650 °C using hydrogen fuel. The enhancement in conductivity and performance was due to increasing the oxygen vacancies in the ceria lattice with the increasing dopant concentration. The bandgap was calculated from UV-Vis data, which shows a red shift when compared with pure ceria. The average crystallite size is in the range of 37-49 nm. DFT was used to analyze the co-doping structure, and the calculated lattice parameter was compared with the experimental lattice parameter.

  13. Effect of patch borders on coercivity in amorphous rare earth-transition metal thin films

    Science.gov (United States)

    Patterson, G.; Fu, H.; Giles, R. C.; Mansuripur, M.

    1991-01-01

    The coercivity at the micron scale is a very important property of magneto-optical media. It is a key factor that determines the magnetic domain wall movement and domain reversal. How the coercivity is influenced by a special type of patch borders is discussed. Patch formation is a general phenomenon in growth processes of amorphous rare earth transition metal thin films. Different patches may stem from different seeds and the patch borders are formed when they merge. Though little is known about the exact properties of the borders, we may expect that the exchange interaction at the patch border is weaker than that within a patch, since there is usually a spatial gap between two patches. Computer simulations were performed on a 2-D hexagonal lattice consisting of 37 complete patches with random shape and size. From the series of simulations we may conclude that the domain in the patch with borders of 30 percent exchange strength can expand most easily to the whole lattice, because the exchange strength can expand most easily to the whole lattice, because the exchange strength of the border is not too high to prevent the domain from growing within the patch and it is not too low to prevent the domain from expanding beyond the patch.

  14. Band edge electronic structure of transition metal/rare earth oxide dielectrics

    Science.gov (United States)

    Lucovsky, Gerald

    2006-10-01

    This article addresses band edge electronic structure of transition metal/rare earth (TM/RE) non-crystalline and nano-crystalline elemental and complex oxide high- k dielectrics for advanced semiconductor devices. Experimental approaches include X-ray absorption spectroscopy (XAS) from TM, RE and oxygen core states, photoconductivity (PC), and visible/vacuum ultra-violet (UV) spectroscopic ellipsometry (SE) combined with ab initio theory is applied to small clusters. These measurements are complemented by Fourier transform infra-red absorption (FTIR), X-ray photoelectron spectroscopy (XPS), high-resolution transmission electron microscopy (HRTEM) and X-ray diffraction (XRD). Two issues are highlighted: Jahn-Teller term splittings that remove d-state degeneracies of states at the bottom of the conduction band, and chemical phase separation and crystallinity in Zr and Hf silicates and ternary (Zr(Hf)O 2) x(Si 3N 4) y(SiO 2) 1- x- y alloys. Engineering solutions for optimization of both classes of high- k dielectric films, including limits imposed on the continued and ultimate scaling of the equivalent oxide thickness (EOT) are addressed.

  15. Facile fabrication of graphene-based aerogel with rare earth metal oxide for water purification

    Science.gov (United States)

    Pan, Liupeng; Liu, Shunli; Oderinde, Olayinka; Li, Kewen; Yao, Fang; Fu, Guodong

    2018-01-01

    We report a one-step facile fabrication of macroscopic multifunctional graphene-based aerogel with three-dimensional interconnected networks under the synergistic effects of the reduction of graphene oxide sheets by L-ascorbic acid and in situ simultaneous deposition of nanoparticles on graphene sheets. The functional components, Nd2O3 nanoparticles, can be easily incorporated with graphene sheets to assemble bulk macroscopic graphene materials under mild conditions. The reduced graphene oxide/neodymium oxide (rGO/Nd2O3) aerogel showed remarkable adsorption capacity towards different types of dyes, especially for anionic dyes, with the adsorption capacity for indigo disulphonate (ID) being more than 220 mg g-1 within one hour while the adsorption capacity at equilibrium is as high as 397 mg g-1. The method proposed is proven to be universal to induce macroscopic assembly of reduced graphene sheets with rare earth metal oxides and thus facilitates to accessing various graphene-based multifunctional nanocomposites in the form of macroscopic aerogels.

  16. SYNTHESIS, CHARACTERIZATION AND APPLICATION OF DIATOMACEOUS EARTH – 4,4-DIAMINODIPHENYLETHER-O-HYDROXYBENZALDEHYDE AS AN ADSORBENT OF Ag(I) METAL ION

    OpenAIRE

    Fatoni, Ahmad; Koesnarpadi, Soerja; Hidayati, Nurlisa

    2010-01-01

    Synthesis, characterization and application of Diatomaceous Earth-4,4-Diamino diphenylether-O-Hydroxybenzaldehyde (diatomaceous earth-DDE-O-Hb) as an adsorbent of Ag(I) metal ion has been done. The aim of the purification of natural diatomaceous earth with KMnO4, H2SO4 and HCl were to obtain pure diatomaceous earth, remove the other compounds and de-alumination, respectively. The adsorbent of diatomaceous earth-DDE-O-Hb was synthesized by reacting pure diatomaceous earth with 3-chloropropyltr...

  17. Tests of prototype salt stripper system for IFR fuel cycle

    International Nuclear Information System (INIS)

    Carls, E.L.; Blaskovitz, R.J.; Johnson, T.R.; Ogata, T.

    1993-01-01

    One of the waste treatment steps for the on-site reprocessing of spent fuel from the Integral Fast Reactor fuel cycles is stripping of the electrolyte salt used in the electrorefining process. This involves the chemical reduction of the actinides and rare earth chlorides forming metals which then dissolve in a cadmium pool. To develop the equipment for this step, a prototype salt stripper system has been installed in an engineering scale argon-filled glovebox. Pumping trails were successful in transferring 90 kg of LiCl-KCl salt containing uranium and rare earth metal chlorides at 500 degree C from an electrorefiner to the stripper vessel at a pumping rate of about 5 L/min. The freeze seal solder connectors which were used to join sections of the pump and transfer line performed well. Stripping tests have commenced employing an inverted cup charging device to introduce a Cd-15 wt % Li alloy reductant to the stripper vessel

  18. Interaction of intermetallic compounds formed by rare earths, scandium, yttrium and 3d-transition metals, with gaseous ammonia

    International Nuclear Information System (INIS)

    Shilkin, S.P.; Volkova, L.S.

    1992-01-01

    Interaction of the RT n intermetallic compounds, where R Sc, Y, rare earths, T = Fe, Co, Ni; n = 2,3,5, with gaseous ammonia under pressure of 1MPa and at temperatures of 293, 723 and 798 K is studied. It is established on the basis of roentgenographic studied, chemical analysis data, X-ray photoelectron spectroscopy and specific surface measurements that metallic matrixes of intermetallides decompose into nitrides and transition metal phases at temperatures of 723 and 798 K under effect of ammonia and independent of structural types of the source materials; partial or complete decomposition of intermetallides through ammonia with formation of transition metal mixture, binary hydrides and nitrides of the most electropositive metal the above systems occurs at the temperature of 293 K depending on the heat of the source compounds and their tendency to decomposition under ammonia effect

  19. Assay of uranium in fused salt cake generated at the natural uranium metal fuel fabrication plants by gamma-ray spectrometry

    International Nuclear Information System (INIS)

    Kalsi, P.C.; Bhanu, A.U.; Sahoo, S.; Iyer, R.H.

    1986-01-01

    A passive gamma-ray spectroscopic method is employed for the assay of uranium in fused salt cake, a scrap produced at the natural uranium metal fuel fabrication plants. The method makes use of NaI(TI) detector coupled with a multichannel analyser. The 1 MeV gamma-ray of 238 U was used for the calibration. The calibration curve was made by counting synthetic mixtures made of U 3 O 8 powder, the heat treatment salt and iron in the form of fine powder. The uranium content in these synthetic mixtures was kept in the range of 1-11 per cent. 23 lots of the fused salt cake taken from three different batches of the salt cake were then analysed by this method. The uranium content of fused salt cake was found to be in the range of 1.70-11.43 per cent. To compare the gamma spectrometric results with a completely independent method, chemical analysis of all the fused salt cakes were also carried out. The NDA results were found to agree within ± 17 per cent with the chemical analysis results. (author)

  20. Metal nitride cluster as a template to tune the electronic and magnetic properties of rare-earth metal containing endohedral fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yang

    2013-10-16

    Rare-earth metal containing endohedral fullerenes have attracted much attention due to the feasibility of encaging metal atom, atoms or cluster inside of carbon cages. By switching the metal atom or cluster entrapped inside of the carbon cage the physical and chemical properties of the fullerene compounds can be tuned. The understanding of magnetic and electrochemical properties of endohedral fullerenes plays an essential role in fundamental scientific researches and potential applications in materials science. In this thesis, synthesizing novel rare-earth metal containing endohedral fullerene structures, studying the properties of these isolated endohedral fullerenes and the strategies of tuning the electronic and magnetic properties of endohedral fullerenes were introduced. The DC-arc discharging synthesis of different lanthanide metal-based (Ho, Ce and Pr) mixed metal nitride clusterfullerenes was achieved. Those rare-earth metal containing endohedral fullerenes were isolated by multi-step HPLC. The isolated samples were characterized by spectroscopic techniques included UV-vis-NIR, FTIR, Raman, LDI-TOF mass spectrometry, NMR and electrochemistry. The Ho-based mixed metal nitride clusterfullerenes Ho{sub x}M{sub 3-x}N rate at C{sub 80} (M= Sc, Lu, Y; x=1, 2) were synthesized by ''reactive gas atmosphere'' method or ''selective organic solid'' route. The isolated samples were characterized by LDI-TOF mass spectrometry, UV-vis-NIR, FTIR, Raman and NMR spectroscopy. The {sup 13}C NMR spectroscopic studies demonstrated exceptional NMR behaviors that resulted from switching the second metal inside of the mixed metal nitride cluster Ho{sub x}M{sub 3-x}N from Sc to Lu and further to Y. The LnSc{sub 2}N rate at C{sub 80} (Ln= Ce, Pr, Nd, Tb, Dy, Ho, Lu) MMNCFs were characterized by {sup 13}C and {sup 45}Sc NMR study respectively. According to Bleaney's theory and Reilley method, the separation of δ{sup PC} and δ{sup con

  1. Metal nitride cluster as a template to tune the electronic and magnetic properties of rare-earth metal containing endohedral fullerenes

    International Nuclear Information System (INIS)

    Zhang, Yang

    2013-01-01

    Rare-earth metal containing endohedral fullerenes have attracted much attention due to the feasibility of encaging metal atom, atoms or cluster inside of carbon cages. By switching the metal atom or cluster entrapped inside of the carbon cage the physical and chemical properties of the fullerene compounds can be tuned. The understanding of magnetic and electrochemical properties of endohedral fullerenes plays an essential role in fundamental scientific researches and potential applications in materials science. In this thesis, synthesizing novel rare-earth metal containing endohedral fullerene structures, studying the properties of these isolated endohedral fullerenes and the strategies of tuning the electronic and magnetic properties of endohedral fullerenes were introduced. The DC-arc discharging synthesis of different lanthanide metal-based (Ho, Ce and Pr) mixed metal nitride clusterfullerenes was achieved. Those rare-earth metal containing endohedral fullerenes were isolated by multi-step HPLC. The isolated samples were characterized by spectroscopic techniques included UV-vis-NIR, FTIR, Raman, LDI-TOF mass spectrometry, NMR and electrochemistry. The Ho-based mixed metal nitride clusterfullerenes Ho x M 3-x N rate at C 80 (M= Sc, Lu, Y; x=1, 2) were synthesized by ''reactive gas atmosphere'' method or ''selective organic solid'' route. The isolated samples were characterized by LDI-TOF mass spectrometry, UV-vis-NIR, FTIR, Raman and NMR spectroscopy. The 13 C NMR spectroscopic studies demonstrated exceptional NMR behaviors that resulted from switching the second metal inside of the mixed metal nitride cluster Ho x M 3-x N from Sc to Lu and further to Y. The LnSc 2 N rate at C 80 (Ln= Ce, Pr, Nd, Tb, Dy, Ho, Lu) MMNCFs were characterized by 13 C and 45 Sc NMR study respectively. According to Bleaney's theory and Reilley method, the separation of δ PC and δ con from δ para was achieved by the primary 13 C and 45 Sc NMR analysis of LnSc 2 N rate at C 80 (I). The

  2. Enrichment of rare earth metal ions by the highly selective adsorption of phytate intercalated layered double hydroxide.

    Science.gov (United States)

    Jin, Cheng; Liu, Huimin; Kong, Xianggui; Yan, Hong; Lei, Xiaodong

    2018-02-27

    Phytate intercalated MgAl layered double hydroxide (MgAl-LDH) was prepared by an anion exchange method with the precursor NO 3 - containing MgAl-LDH. The final as-synthesized product [Mg 0.69 Al 0.31 (OH) 2 ] (phytateNa 6 ) 0.05 (NO 3 ) 0.01 ·mH 2 O (phytate-LDH) has highly selective adsorption ability for some metal ions and can be used to enrich rare earth metal ions in mixed solution, such as Pr 3+ and Ce 3+ from a mixed solution of them with Pb 2+ and Co 2+ . At first, phytate-LDH has good adsorption performance for these ions in single metal ion solutions. At low concentration (below 10 mg L -1 ), all the capture rates of the four metal ions were more than 97%, for highly toxic Pb 2+ it was even up to nearly 100%, and a high capture rate (99.87%) was maintained for Pb 2+ at a high concentration (100 mg L -1 ). When all the four metal ions are co-existing in aqueous solution, the selectivity order is Pb 2+ ≫ Pr 3+ ≈ Ce 3+ > Co 2+ . In a solution containing mixtures of the three metal ions of Pr 3+ , Ce 3+ , and Co 2+ , the selectivity order is Pr 3+ ≈ Ce 3+ ≫ Co 2+ , and in a solution containing mixtures of Pr 3+ with Co 2+ and Ce 3+ with Co 2+ , the selectivity orders are Pr 3+ ≫ Co 2+ and Ce 3+ ≫ Co 2+ , respectively. The high selectivity and adsorption capacities for Pb 2+ , Co 2+ , Pr 3+ , and Ce 3+ result in the efficient removal of Pb 2+ and enrichment of the rare earth metal ions Pr 3+ and Ce 3+ by phytate-LDH. Based on the elemental analysis, it is found that the difference of the adsorption capacities is mainly due to the different coordination number of them with phytate-LDH. With molecular simulation, we believe that the adsorption selectivity is due to the difference of the binding energy between the metal ion and phytate-LDH. Therefore, the phytate-LDH is promising for the enrichment and/or purification of the rare earth metal ions and removal of toxic metal ions from waste water.

  3. Extraction of rare earth metals with 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester in the presence of diethylenetriaminepentaacetic acid in aqueous phase

    International Nuclear Information System (INIS)

    Kubota, Fukiko; Goto, Masahiro; Nakashio, Fumiyuki

    1993-01-01

    The extraction equilibria of rare earth metals with 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (commercial name, PC-88A, henceforth abbreviated as HR) dissolved in n-heptane were measured at 303 K. It was found that rare earth metals are extracted with the dimer of the extractant, (HR) 2 , as follows. M aq 3+ + 3(HR) 2 org MR 3 · 3HR org + 3H aq + The extraction equilibrium constants of metals were obtained and compared with the extraction equilibrium constants obtained by di(2-ethylhexyl)phosphoric acid (henceforth DZEHPA). Furthermore, the extraction equilibria of rare earth metals with PC-88A in the presence of diethylenetriaminepentaacetic acid (henceforth DTPA) in an aqueous phase were also measured to discuss the effect of DTPA on the extraction of rare earth metals. 13 refs., 8 figs., 2 tabs

  4. Determination of metals and rare earths in leach solution of phosphogypsum by instrumental neutron activation analysis (INAA)

    International Nuclear Information System (INIS)

    Costa, Gabriela J.L.; Saueia, Catia H.R.; Mazzilli, Barbara P.

    2011-01-01

    The phosphogypsum is a sub-product of the fertilizer industries and is composed of the gypsum matrix (CaSO 4 .2H 2 O) which naturally contains high tenors of impurities such as 2P O 5 and metals coming from the original phosphat rock. The Brazilian phosphogypsum and the various uses has been researched through his elementary and radiochemistry characterization. This work determine the metals (As, Ba, Co and Se) and rare earths (La, Ce, Sm, Eu, Tb and Lu) presents in samples of phosphogypsum leach solutions

  5. Electronic Stopping of Slow Protons in Transition and Rare Earth Metals: Breakdown of the Free Electron Gas Concept.

    Science.gov (United States)

    Roth, D; Bruckner, B; Moro, M V; Gruber, S; Goebl, D; Juaristi, J I; Alducin, M; Steinberger, R; Duchoslav, J; Primetzhofer, D; Bauer, P

    2017-03-10

    The electronic stopping cross sections (SCS) of Ta and Gd for slow protons have been investigated experimentally. The data are compared to the results for Pt and Au to learn how electronic stopping in transition and rare earth metals correlates with features of the electronic band structures. The extraordinarily high SCS observed for protons in Ta and Gd cannot be understood in terms of a free electron gas model, but are related to the high densities of both occupied and unoccupied electronic states in these metals.

  6. An efficient way to prepare silver nanorods in high concentration by polyol method without adding other metal or salt

    International Nuclear Information System (INIS)

    Chen Yong; Guan Jianguo; Xie Hongquan

    2012-01-01

    Using ethylene glycol as solvent and reductant, polyvinyl pyrrolidone(PVP) as capping agent under the action of appropriately preformed silver crystal seeds and controlled addition rates of silver nitrate and PVP solution, silver nanorods with length of 2–15 μm and diameter of 200–880 nm can be obtained in high concentration of AgNO 3 as 0.50 M. In the absence of the preformed seeds, nanorods cannot be obtained as the main product, if the AgNO 3 concentration is over 0.10 M. It is necessary to use the appropriately preformed silver crystal seeds for the high concentration preparation of silver nanorods. Transmission Electron Microscopy images showed that Ag seeds preformed at appropriate silver nitrate concentrations exhibited the multiply twinned particles of decahedral shape(MTPs), which formed Ag nanorods in the presence of PVP. Through study of the effects of various factors on the nanostructure of silver, the favorable conditions are: appropriately preformed seeds concentration at 6.54–9.81 mM, addition rate of AgNO 3 solution at 0.30–0.43 mL min −1 and molar ratio of PVP/AgNO 3 at 1.1–1.4, in order to control the crystal growth rate of silver matching the reduction rate of AgNO 3 by ethylene glycol. The nanorods obtained were characterized by Scanning Electron Microscopy, EDX, XRD, Raman spectrometry, Infrared Spectrophotometry and Ultraviolet Spectrophotometry. On the base of the above results, the mechanism of rates matching for obtaining silver nanorods was briefly discussed. This method is a simple, facile and economical method using high concentration with high yield without using other metal or salt to massively synthesize silver nanorods through adding preformed silver seeds to control the reduction rate of silver nitrate and the crystal growth rate of silver nanorods. As compared to the conventional polyol method using lower silver nitrate concentration, this method can save ethylene glycol used and time of operation and the as

  7. Environmentally Friendly Economical Sequestration of Rare Earth Metals from Geothermal Waters

    Energy Technology Data Exchange (ETDEWEB)

    Stull, Dean P. [Tusaar Corp., Lafayette, CO (United States)

    2016-05-26

    The purpose of this work was to complete a proof of concept study to apply and validate a novel method developed by Tusaar for the capture and recovery of rare earth elements (known as REEs) and other critical and valuable elements from geothermal waters produced from deep within the earth. Geothermal water provides heat for power production at many geothermal power plants in the western United States. The target elements, the REEs, are vital to modern day electronics, batteries, motors, automobiles and many other consumer favorites and necessities. Currently there are no domestic sources of REEs while domestic and international demand for the products they are used in continues to rise. Many of the REEs are considered “strategically” important. A secure supply of REEs in the USA would benefit consumers and the country at large. A new method to recover these REEs from geothermal waters used at existing geothermal power plants around the country is a high priority and would benefit consumers and the USA. The result of this project was the successful development and demonstration of an integrated process for removal and recovery of the REEs from synthetic geothermal brines on a small laboratory scale. The work included preparation of model geothermal brines to test, selection of the most effective proprietary sorbent media to capture the REEs and testing of the media under a variety of potential operating conditions. Geothermal brines are generally very high in salt content and contain a wide range of elements and anions associated with the rock layers from which they are produced. Processing the geothermal water is difficult because it is corrosive and the dissolved minerals in the water precipitate easily once the temperature and pressure change. No commercial technologies have been shown to be effective or robust enough under these geothermal brine conditions to be commercially viable for removal of REEs. Technologies including ion exchange, traditional

  8. 1,3-Diene Polymerization Mediated by Homoleptic Tetramethylaluminates of the Rare-Earth Metals

    Directory of Open Access Journals (Sweden)

    Christoph O. Hollfelder

    2018-02-01

    Full Text Available During the past two decades homoleptic tetramethylaluminates of the trivalent rare-earth metals, Ln(AlMe43, have emerged as useful components for efficient catalyst design in the field of 1,3-diene polymerization. Previous work had focused on isoprene polymerization applying Ln(AlMe43 precatalysts with Ln = La, Ce, Pr, Nd, Gd and Y, in the presence of Et2AlCl as an activator. Polymerizations employing Ln(AlMe43 with Ln = La, Y and Nd along with borate/borane co-catalysts [Ph3C][B(C6F54], [PhNMe2H][B(C6F54] and [B(C6F53] were mainly investigated for reasons of comparison with ancillary ligand-supported systems (cf. half-sandwich complexes. The present study investigates into a total of eleven rare-earth elements, namely Ln = La, Ce, Pr, Nd, Gd, Tb, Dy, Ho, Y, Er and Lu. A full overview on the polymerization behavior of Ln(AlMe43 in the presence of perfluorinated borate/borane cocatalysts and R2AlCl-type activators (R = Me, Et is provided, probing the monomers isoprene and 1,3-butadiene (and preliminary ethylene. Virtually complete cis-1,4-selectivities are obtained for several catalyst/cocatalyst combinations (e.g., Gd(AlMe43/Me2AlCl, >99.9%. Insights into the ‘black box’ of active species are obtained by indirect observations via screening of pre-reaction time and cocatalyst concentration. The microstructure of the polydienes is investigated by combined 1H/13C NMR and ATR-IR spectroscopies. Furthermore, the reaction of [LuMe6(Li(thfx3] with AlMe3 has been applied as a new strategy for the efficient synthesis of Lu(AlMe43. The solid-state structures of Gd(AlMe43 and Tb(AlMe43 are reported.

  9. Surface Nanostructures Formed by Phase Separation of Metal Salt-Polymer Nanocomposite Film for Anti-reflection and Super-hydrophobic Applications

    Science.gov (United States)

    Con, Celal; Cui, Bo

    2017-12-01

    This paper describes a simple and low-cost fabrication method for multi-functional nanostructures with outstanding anti-reflective and super-hydrophobic properties. Our method employed phase separation of a metal salt-polymer nanocomposite film that leads to nanoisland formation after etching away the polymer matrix, and the metal salt island can then be utilized as a hard mask for dry etching the substrate or sublayer. Compared to many other methods for patterning metallic hard mask structures, such as the popular lift-off method, our approach involves only spin coating and thermal annealing, thus is more cost-efficient. Metal salts including aluminum nitrate nonahydrate (ANN) and chromium nitrate nonahydrate (CNN) can both be used, and high aspect ratio (1:30) and high-resolution (sub-50 nm) pillars etched into silicon can be achieved readily. With further control of the etching profile by adjusting the dry etching parameters, cone-like silicon structure with reflectivity in the visible region down to a remarkably low value of 2% was achieved. Lastly, by coating a hydrophobic surfactant layer, the pillar array demonstrated a super-hydrophobic property with an exceptionally high water contact angle of up to 165.7°.

  10. A miniature single element effusion cell for the vacuum deposition of transition-metal and rare-earth elements

    Science.gov (United States)

    Harris, V. G.; Koon, N. C.

    1997-08-01

    A miniature single element effusion cell has been fabricated and tested that allows for the high-vacuum deposition of a variety of transition-metal and rare-earth elements. The cell is designed to operate under high-vacuum conditions, ≈10-9 Torr, with low power demands, <200 W. The virtues of this evaporator are the simplicity of design and ease of fabrication, assembly, maintenance, and operation.

  11. Effect of alkaline earth metal and magnesium cations on cadmium extraction from chloride solutions by tributyl phosphate

    International Nuclear Information System (INIS)

    Prokuev, V.A.; Belousov, E.A.

    1985-01-01

    At 298 K thermodynamic constants of cadmium (2) extraction from chloride solutions of magnesium, calcium, strontium and barium by tributyl phosphate are calculated. It is established, that logarithm of the thermodynamic extraction constant is in a linear dependence from the change in the cation hydration enthalpy in agqueous solution. It is shown, that activity coefficient of neutral complex CdVCl 2 differs from one, and it is the higher the more stable the complex is in alkaline earth metal chloride solutions

  12. Electrical resistivities and solvation enthalpies for solutions of salts in liquid alkali metals

    International Nuclear Information System (INIS)

    Hubberstey, P.; Dadd, A.T.

    1982-01-01

    An empirical correlation is shown to exist between the resistivity coefficients drho/dc for solutes in liquid alkali metals and the corresponding solvation enthalpies Usub(solvn) of the neutral gaseous solute species. Qualitative arguments based on an electrostatic solvation model in which the negative solute atom is surrounded by a solvation sphere of positive solvent ion cores are used to show that both parameters are dependent on the charge density of the solute atom and hence on the extent of charge transfer from solvent to solute. Thus as the charge density of the solute increases, the solvation enthalpy increases regularly and the resistivity coefficients pass through a maximum to give the observed approximately parabolic drho/dc versus Usub(solvn) relationship. (Auth.)

  13. Super earth interiors and validity of Birch's Law for ultra-high pressure metals and ionic solids

    Science.gov (United States)

    Ware, Lucas Andrew

    2015-01-01

    Super Earths, recently detected by the Kepler Mission, expand the ensemble of known terrestrial planets beyond our Solar System's limited group. Birch's Law and velocity-density systematics have been crucial in constraining our knowledge of the composition of Earth's mantle and core. Recently published static diamond anvil cell experimental measurements of sound velocities in iron, a key deep element in most super Earth models, are inconsistent with each other with regard to the validity of Birch's Law. We examine the range of validity of Birch's Law for several metallic elements, including iron, and ionic solids shocked with a two-stage light gas gun into the ultra-high pressure, temperature fluid state and make comparisons to the recent static data.

  14. Spin-disorder resistivity of heavy rare-earth metals from Gd to Tm: An ab-initio study

    Science.gov (United States)

    Glasbrenner, James; Belashchenko, Kirill

    2010-03-01

    Electrical resistivity of heavy rare-earth metals has a dominant contribution from thermal spin disorder scattering. In the paramagnetic state, this spin-disorder resistivity (SDR) decreases through the Gd-Tm series. Models based on the assumption of fully localized 4f states treated as S or J multiplets predict that SDR is proportional to S^2 (S is the 4f shell spin) times a quantum correction (S+1)/S or (J+1)/J. The interpretation of this correction using experimental results is ambiguous. Since the 4f bandwidth is not small compared to the multiplet splitting, it is not clear whether the 4f shells in rare-earth metals behave as if they were fully localized and have a good quantum number S or J. To address this issue, in this work we calculate the paramagnetic SDR of the rare-earth metal Gd-Tm series using a non-collinear implementation of the tight-binding linear muffin-tin orbital method. The conductance is found using the Landauer-B"uttiker approach applied to the active region of a varying size, averaging the conductance over random spin-disorder configurations and fitting its size dependence to Ohm's law. The results are compared with experiment and discussed. The sensitivity to basis set and the treatment of the 4f electrons, as well as the role of exchange enhancement in the conduction band is considered. The issue of the quantum correction is examined in light of the new results.

  15. Influence of strain and polycrystalline ordering on magnetic properties of high moment rare earth metals and alloys

    International Nuclear Information System (INIS)

    Scheunert, G; Ward, C; Hendren, W R; Bowman, R M; Lapicki, A A; Hardeman, R; Mooney, M; Gubbins, M

    2014-01-01

    Despite being the most suitable candidates for solenoid pole pieces in state-of-the-art superconductor-based electromagnets, the intrinsic magnetic properties of heavy rare earth metals and their alloys have gained comparatively little attention. With the potential of integration in micro and nanoscale devices, thin films of Gd, Dy, Tb, DyGd and DyTb were plasma-sputtered and investigated for their in-plane magnetic properties, with an emphasis on magnetization versus temperature profiles. Based on crystal structure analysis of the polycrystalline rare earth films, which consist of a low magnetic moment fcc layer at the seed interface topped with a higher moment hcp layer, an experimental protocol is introduced which allows the direct magnetic analysis of the individual layers. In line with the general trend of heavy lanthanides, the saturation magnetization was found to drop with increasing unit cell size. In situ annealed rare earth films exceeded the saturation magnetization of a high-moment Fe 65 Co 35 reference film in the cryogenic temperature regime, proving their potential for pole piece applications; however as-deposited rare earth films were found completely unsuitable. In agreement with theoretical predictions, sufficiently strained crystal phases of Tb and Dy did not exhibit an incommensurate magnetic order, unlike their single-crystal counterparts which have a helical phase. DyGd and DyTb alloys followed the trends of the elemental rare earth metals in terms of crystal structure and magnetic properties. Inter-rare-earth alloys hence present a desirable blend of saturation magnetization and operating temperature. (paper)

  16. IUPAC-NIST Solubility Data Series. 100. Rare Earth Metal Fluorides in Water and Aqueous Systems. Part 3. Heavy Lanthanides (Gd–Lu)

    Energy Technology Data Exchange (ETDEWEB)

    Mioduski, Tomasz [Institute of Nuclear Chemistry and Technology, 03195 Warszawa (Poland); Gumiński, Cezary, E-mail: cegie@chem.uw.edu.pl [Department of Chemistry, University of Warsaw, 02093 Warszawa (Poland); Zeng, Dewen, E-mail: dewen-zeng@hotmail.com [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China)

    2015-06-15

    This is the third part of the volume devoted to solubility data for the rare earth metal (REM) fluorides in water and in aqueous ternary and multicomponent systems. It covers experimental results of trivalent fluorides of Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu (so-called heavy lanthanides), since no quantitative data on solubilities of TbF{sub 4} and YbF{sub 2} (the most stable compounds at these valencies) are available. The related literature has been covered through the end of 2014. Compilations of all available papers with the solubility data are introduced for each REM fluoride with a corresponding critical evaluation. Every such assessment contains a collection of all solubility results in aqueous solution, a selection of suggested solubility data, a solubility equation, and a brief discussion of the multicomponent systems. Only simple fluorides (no complexes or double salts) are treated as the input substances in this report. General features of the systems, such as nature of the equilibrium solid phases, solubility as a function of temperature, influence of ionic strength, solution pH, mixed solvent medium on the solubility, quality of the solubility results, and the solubility as a function of REM atomic number, have already been presented in Part 1 of the volume.

  17. Microstructure and composition of rare earth-transition metal-aluminium-magnesium alloys

    Directory of Open Access Journals (Sweden)

    Lia Maria Carlotti Zarpelon

    2008-03-01

    Full Text Available The determination of the microstructure and chemical composition of La0.7-xPr xMg0.3Al 0.3Mn0.4Co0.5 Ni3.8 (0 < x < 0.7 metal hydride alloys has been carried out using scanning electron microscopy (SEM, energy dispersive X ray analysis (EDX and X ray diffraction analysis (XRD. The substitution of La with Pr changed the grain structure from equiaxial to columnar. The relative atomic ratio of rare earth to (Al, Mn, Co, Ni in the matrix phase was 1:5 (LaNi5-type structure. Magnesium was detected only in two other phases present. A grey phase revealed 11 at.% Mg and the concentration ratios of other elements indicated the composition to be close to PrMgNi4. A dark phase was very heterogeneous in composition, attributed to the as-cast state of these alloys. The phases identified by XRD analysis in the La0.7Mg0.3Al0.3Mn0.4Co 0.5Ni3.8 alloy were: La(Ni,Co5, LaAl(Ni,Co4, La2(Ni,Co7 and AlMn(Ni,Co2. Praseodymium favors the formation of a phase with a PuNi3-type structure. Cobalt substituted Ni in the structures and yielded phases of the type: Pr(Ni,Co5 and Pr(Ni,Co3.

  18. Materials flow analysis of neodymium, status of rare earth metal in the Republic of Korea.

    Science.gov (United States)

    Swain, Basudev; Kang, Leeseung; Mishra, Chinmayee; Ahn, JoongWoo; Hong, Hyun Seon

    2015-11-01

    Materials flow analysis of neodymium, status of rare earth elements (REEs) in the Republic of Korea has been investigated. Information from various resources like the Korean Ministry of Environment, Korea international trade association, United Nations Commodity Trade Statistics Database and from individual industry were collected and analyzed for materials flow analysis of neodymium. Demand of neodymium in the Republic of Korea for the year 2010 was 409.5 tons out of which the majority of neodymium, i.e., 68.41% was consumed by domestic electronics industry followed by medical appliances manufacturing (13.36%). The Republic Korea is one of the biggest consumer and leading exporter of these industrial products, absolutely depends on import of neodymium, as the country is lacking natural resources. The Republic of Korea has imported 325.9 tons of neodymium permanent magnet and 79.5 tons of neodymium containing equipment parts mainly for electronics, medical appliances, and heavy/light vehicles manufacturing industry. Out of which 95.4 tons of neodymium permanent magnet get exported as an intermediate product and 140.6 tons of neodymium in the form of consumable products get exported. Worldwide the neodymium is at the high end of supply chain critical metal because of increasing demand, scarcity and irreplaceable for technological application. To bring back the neodymium to supply stream the recycling of end of life neodymium-bearing waste can be a feasible option. Out of total domestic consumption, only 21.9 tons of neodymium have been collected and subsequently recycled. From material flow analysis, the requirement for an efficient recycling system and element-wise material flow management for these REEs in the Republic of Korea were realized and recommended. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Advances in molten salt electrochemistry towards future energy systems

    International Nuclear Information System (INIS)

    Ito, Yasuhiko

    2005-01-01

    This review article describes some selected novel molten salt electrochemical processes which have been created/developed by the author and his coworkers, with emphasis on the applications towards future energy systems. After showing a perspective of the applications of molten salt electrochemistry from the viewpoints of energy and environment, several selected topics are described in detail, which include nitride fuel cycle in a nuclear field, hydrogen energy system coupled with ammonia economy, thermally regenerative fuel cell systems, novel Si production process for solar cell and novel molten salt electrochemical processes for various energy and environment related functional materials including nitrides, rare earth-transition metal alloys, fine particles obtained by plasma-induced electrolysis, and carbon film. And finally, the author stresses again, the importance and potential of molten salt electrochemistry, and encourages young students, scientists and researchers to march in a procession hand in hand towards a bright future of molten salts. (author)

  20. Experimental and Modeling Studies on the Conversion of Inulin to 5-Hydroxymethylfurfural Using Metal Salts in Water

    Directory of Open Access Journals (Sweden)

    Boy Arief Fachri

    2015-12-01

    Full Text Available Inulin, a plant polysaccharide consisting of mainly d-fructose units, is considered an interesting feed for 5-hydroxymethylfurfural (HMF, a top 12 bio-based chemical. We here report an exploratory experimental study on the use of a wide range of homogeneous metal salts as catalysts for the conversion of inulin to HMF in water. Best results were obtained using CuCl2. Activity-pH relations indicate that the catalyst activity of CuCl2 is likely related to Lewis acidity and not to Brönsted acidity. The effects of process conditions on HMF yield for CuCl2 were systematically investigated and quantified using a central composite design (160–180 °C, an inulin loading between 0.05 and 0.15 g/mL, CuCl2 concentration in range of 0.005–0.015 M, and a reaction time between 10 and 120 min. The highest experimental HMF yield in the process window was 30.3 wt. % (39 mol %, 180 °C, 0.05 g/mL inulin, 0.005 M CuCl2 and a reaction time of 10 min. The HMF yields were modelled using non-linear, multi variable regression and good agreement between experimental data and model were obtained.

  1. Effects of metal salt addition on odor and process stability during the anaerobic digestion of municipal waste sludge.

    Science.gov (United States)

    Abbott, Timothy; Eskicioglu, Cigdem

    2015-12-01

    Anaerobic digestion (AD) is an effective way to recover energy and nutrients from organic waste; however, several issues including the solubilization of bound nutrients and the production of corrosive, highly odorous and toxic volatile sulfur compounds (VSCs) in AD biogas can limit its wider adoption. This study explored the effects of adding two different doses of ferric chloride, aluminum sulfate and magnesium hydroxide directly to the feed of complete mix semi-continuously fed mesophilic ADs on eight of the most odorous VSCs in AD biogas at three different organic loading rates (OLR). Ferric chloride was shown to be extremely effective in reducing VSCs by up to 87%, aluminum sulfate had the opposite effect and increased VSC levels by up to 920%, while magnesium hydroxide was not shown to have any significant impact. Ferric chloride, aluminum sulfate and magnesium hydroxide were effective in reducing the concentration of orthophosphate in AD effluent although both levels of alum addition caused digester failure at elevated OLRs. Extensive foaming was observed within the magnesium hydroxide dosed digesters, particularly at higher doses and high OLRs. Certain metal salt additions may be a valuable tool in overcoming barriers to AD and to meet regulatory targets. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Reactivity of Crystalline Silicotitanate (CST) and Hazardous Metal/Actinide Loading During Low Curie Salt Use

    Energy Technology Data Exchange (ETDEWEB)

    WILLIAM, WILMARTH

    2004-11-30

    Crystalline Silicotitanate (CST) in its engineered form (IONSIV (registered) IE-911) continues to be studied for possible use for removing radioactive cesium from several types of waste solutions at the Savannah River Site. This study involved deriving information about spent CST that assists in determining possible disposition alternatives. Results for this work include: After passing 3000 column volumes of a dissolved saltcake simulant containing RCRA hazardous metals, the spent CST passed a TCLP test and is RCRA nonhazardous. The spent CST was found to have transuranic concentrations greater than the TRU limit of 100 nCi/g. The triplicate measurement showed TRU levels greater than 4000 nCi/g. Studies involving simulating storage of ground CST in sludge slurries indicated no detrimental effects on the measured yield stress or viscosity of the slurries when stored for up to 4 months at 50 degrees C. During the storage testing, there was no indication of significant degradation of the C ST as measured by in growth of CST-specific elements in the liquid phase of the slurry. Also, during storage tests minor desorption of cesium from the ground CST material was observed.

  3. SYNTHESIS, CHARACTERIZATION AND APPLICATION OF DIATOMACEOUS EARTH – 4,4-DIAMINODIPHENYLETHER-O-HYDROXYBENZALDEHYDE AS AN ADSORBENT OF Ag(I METAL ION

    Directory of Open Access Journals (Sweden)

    Ahmad Fatoni

    2010-12-01

    Full Text Available Synthesis, characterization and application of Diatomaceous Earth-4,4-Diamino diphenylether-O-Hydroxybenzaldehyde (diatomaceous earth-DDE-O-Hb as an adsorbent of Ag(I metal ion has been done. The aim of the purification of natural diatomaceous earth with KMnO4, H2SO4 and HCl were to obtain pure diatomaceous earth, remove the other compounds and de-alumination, respectively. The adsorbent of diatomaceous earth-DDE-O-Hb was synthesized by reacting pure diatomaceous earth with 3-chloropropyltrimethoxysilane, 4,4-diaminodiphenylether (DDE and O-hydroxybenzaldehyde (O-Hb. The FTIR spectroscopy was used to identify Schiff base group in diatomaceous earth-DDE-O-Hb adsorbent. The diatomaceous earth-DDE-O-Hb was applied as adsorbent in the adsorption of Ag(I metal ion. Parameters influencing the interaction such as time, pH and concentration were optimized. The result showed that diatomaceous earth-DDE-O-Hb adsorbent have Schiff base group. The interaction time of 90 min showed that 70.79% of Ag(I metal ions at the concentration of 100 ppm can be adsorbed by diatomaceous earth-DDE-O-Hb adsorbent. At the pH solution between 2 to 7, the concentration of 100 ppm of Ag(I metal ion that can adsorbed by diatomaceous earth-DDE-O-Hb adsorbent was up to 98% and at the concentration of 25 ppm Ag(I metal ion, the adsorption of Ag(I by diatomaceous earth-DDE-O-Hb adsorbent was near 91%.

  4. Influences of hydrological regime on heavy metal and salt ion concentrations in intertidal sediment from Chongming Dongtan, Changjiang River estuary, China

    Science.gov (United States)

    Zhao, Jiale; Gao, Xiaojiang; Yang, Jin

    2017-11-01

    The tidal flat along the Changjiang (Yangtze) River estuary has long been reclaimed for the agricultural purposes, with the prevailing hydrological conditions during such pedogenic transformations being of great importance to their successful development. In this study, samples of surface sediment from Chongming Dongtan, situated at the mouth of the Changjiang River estuary, were collected and analyzed in order to understand how hydrological management can influence the concentrations of heavy metals and salt ions in pore water, and chemical fractionation of heavy metals during the reclamation process. We performed a series of experiments that simulated three different hydrological regimes: permanent flooding (R1), alternative five-day periods of wetting and drying (R2), continuous field capacity (R3). Our results exhibited good Pearson correlations coefficients between heavy metals and salt ions in the pore water for both R1 and R2. In particular, the concentrations of salt ions in the pore water decreased in all three regimes, but showed the biggest decline in R2. With this R2 experiment, the periodic concentration patterns in the pore water varied for Fe and Mn, but not for Cr, Cu, Pb and Zn. Neither the fractionation of Ni nor the residual fractions of any metals changed significantly in any regime. In R1, the reducible fractions of heavy metals (Cr, Cu, Zn and Pb) in the sediment decreased, while the acid extractable fractions increased. In R2, the acid extractable and the reducible fractions of Cr, Cu, Zn and Pb both decreased, as did the oxidizable fraction of Cu. These data suggest that an alternating hydrological regime can reduce both salinity and the availability of heavy metals in sediments.

  5. Recent advances in syntheses and biomedical applications of nano-rare earth metal-organic framework materials

    Directory of Open Access Journals (Sweden)

    Xin Pengyan

    2017-12-01

    Full Text Available In recent years,the syntheses of nano-rare earth metal-organic framework (MOF materials and their applications in biomedicine,especially in the diagnosis and treatment of cancer have attracted extensive attentions.On the one hand,nano-rare earth MOFs,which have unique optical and magnetic properties,are promising multimodal imaging contrast agents for biomedical imaging,such as fluorescence imaging and magnetic resonance imaging.On the other hand,nano-rare earth MOFs have various compositions and structures,and excellent intrinsic properties such as large specific surface area,high pore volume and tunable pore size,which enable them to perform as promising nanoplatforms for drug delivery.Therefore,nano-rare earth MOFs may provide a new platform for the development of diagnostic and therapeutic reagents.In this article,the recent advances in the syntheses of nano-rare earth MOFs and their applications in biomedicine are summarized.

  6. A binary catalyst system of a cationic Ru-CNC pincer complex with an alkali metal salt for selective hydroboration of carbon dioxide.

    Science.gov (United States)

    Ng, Chee Koon; Wu, Jie; Hor, T S Andy; Luo, He-Kuan

    2016-09-27

    Binary catalyst systems comprising a cationic Ru-CNC pincer complex and an alkali metal salt were developed for selective hydroboration of CO 2 utilizing pinacolborane at r.t. and 1 atm CO 2 , with the combination of [Ru(CNC Bn )(CO) 2 (H)][PF 6 ] and KOCO 2 t Bu producing formoxyborane in 76% yield. A bicyclic catalytic mechanism was proposed and discussed.

  7. A novel molten-salt electrochemical cell for investigating?the reduction of uranium dioxide to uranium metal by lithium using in situ synchrotron radiation

    OpenAIRE

    Brown, Leon D.; Abdulaziz, Rema; Jervis, Rhodri; Bharath, Vidal; Mason, Thomas J.; Atwood, Robert C.; Reinhard, Christina; Connor, Leigh D.; Inman, Douglas; Brett, Daniel J. L.; Shearing, Paul R.

    2017-01-01

    A novel electrochemical cell has been designed and built to allow for in situ energy-dispersive X-ray diffraction measurements to be made during reduction of UO2 to U metal in LiCl?KCl at 500?C. The electrochemical cell contains a recessed well at the bottom of the cell into which the working electrode sits, reducing the beam path for the X-rays through the molten-salt and maximizing the signal-to-noise ratio from the sample. Lithium metal was electrodeposited onto the UO2 working electrode b...

  8. A study on the electrolytic reduction of U3O8 to uranium metal in LiCl-Li2O molten salt

    International Nuclear Information System (INIS)

    Seo, J. S.; Heo, J. M.; Hong, S. S.; Kang, D. S.; Park, S. W.

    2002-01-01

    New electrolytic reduction technology was proposed that is based on the intregration of metallization of U 3 O 8 and Li 2 O electrowinning. In this electrolytic reduction reaction, electrolytically reduced Li deposits on cathode and simultaneously reacts with uranium oxide to produce uranium metal showing more than 99% conversion. For the verification of process feasibility, the experiments to obtain basic data on the metallization of uranium oxide, materials for cathode and anode electrode, the characteristics of closed recycle of Li 2 O and mass transfer were carried out. This evolutionary electrolytic reduction technology would give benefits over the conventional Li-reduction process improving economic viability such as: avoidance of handling of chemically active Li-LiCl molten salt, increase of metallization yield, and simplification of process

  9. A mathematical model of quasi-equilibrium counter-flow processes of rare earth metal separation by solvent extraction when varying the composition of raw material

    International Nuclear Information System (INIS)

    Pyartman, A.K.; Puzikov, E.A.; Kopyrin, A.A.

    1994-01-01

    A mathematical model for description of rare earth metals (3) distribution, depending on the number of contact steps, for quasiequilibrium counter-flow processes of rare earth metals (3) separation by the method of solvent extraction with varying the composition of initial source material is suggested. Algorithm of calculation using computer is provided. The mathematical model is employed for selecting the optimal conditions of didymium concentrate separation. 7 refs., 3 figs., 1 tab

  10. Synthesis and characterization of rare-earth oxide transition-metal arsenides and selenides

    Energy Technology Data Exchange (ETDEWEB)

    Peschke, Simon Friedrich

    2017-04-06

    The present thesis includes two different quaternary systems that have been studied extensively. On the one hand, several samples of the REFeAsO{sub 1-x}F{sub x} family of iron-based superconductors were prepared using a novel solid state metathesis reaction, which also provided a possibility to prepare late rare-earth compounds of this family at ambient pressure. Comparison of structural and physical properties of those samples with samples from conventional solid state and high pressure syntheses revealed both, commonalities as well as striking differences. The observations gave reason to the conclusion that superconducting properties strongly depend, beside electronic infl uence, on the structural parameters. On the other hand, the quaternary system RE-T-Se-O with T = Ti-Mn was investigated using a NaI/KI flux mediated synthesis route. It has been shown that oC -La{sub 2}O{sub 2}MnSe{sub 2} is exclusively accessible in su fficient purity by the use of a fl ux material. Therefore, further syntheses in this quaternary system were performed by a flux mediated synthesis route leading to a large amount of new materials. Among them, a new polymorph mC-La{sub 2}O{sub 2}MnSe{sub 2} which forms, together with La{sub 4}MnSe{sub 3}O{sub 4} and La{sub 6}MnSe{sub 4}O{sub 6}, the series La{sub 2n+2}MnSe{sub n+2}O{sub 2n+2}. In addition, the alternative preparation method also enabled a large scale synthesis of the first examples of rare-earth chromium oxyselenides with chromium in the oxidation state +II, namely RE{sub 2}CrSe{sub 2}O{sub 2} (RE = La-Nd), which opened the door to study their magnetism in detail by powder neutron diffraction and muon spin rotation techniques. Research into the La-V-Se-O system revealed the first fi ve quaternary compounds of this family with interesting magnetic properties including ferromagnetism, antiferromagnetism, metamagnetism and more complex behaviour. In addition, the crystal structure of two new quaternary titanium containing

  11. Characterization of a salt resistant bacterial strain Proteus sp. NA6 capable of decolorizing reactive dyes in presence of multi-metal stress.

    Science.gov (United States)

    Abbas, Naila; Hussain, Sabir; Azeem, Farrukh; Shahzad, Tanvir; Bhatti, Sajjad Haider; Imran, Muhammad; Ahmad, Zulfiqar; Maqbool, Zahid; Abid, Muhammad

    2016-11-01

    Microbial biotechnologies for the decolorization of textile wastewaters have attracted worldwide attention because of their economic suitability and easiness in handling. However, the presence of high amounts of salts and metal ions in textile wastewaters adversely affects the decolorization efficiency of the microbial bioresources. In this regard, the present study was conducted to isolate salt tolerant bacterial strains which might have the potential to decolorize azo dyes even in the presence of multi-metal ion mixtures. Out of the tested 48 bacteria that were isolated from an effluent drain, the strain NA6 was found relatively more efficient in decolorizing the reactive yellow-2 (RY2) dye in the presence of 50 g L(-1) NaCl. Based on the similarity of its 16S rRNA gene sequence and its position in a phylogenetic tree, this strain was designated as Proteus sp. NA6. The strain NA6 showed efficient decolorization (>90 %) of RY2 at pH 7.5 in the presence of 50 g L(-1) NaCl under static incubation at 30 °C. This strain also had the potential to efficiently decolorize other structurally related azo dyes in the presence of 50 g L(-1) NaCl. Moreover, Proteus sp. NA6 was found to resist the presence of different metal ions (Co(+2), Cr(+6), Zn(+2), Pb(+2), Cu(+2), Cd(+2)) and was capable of decolorizing reactive dyes in the presence of different levels of the mixtures of these metal ions along with 50 g L(-1) NaCl. Based on the findings of this study, it can be suggested that Proteus sp. NA6 might serve as a potential bioresource for the biotechnologies involving bioremediation of textile wastewaters containing the metal ions and salts.

  12. Crystal fields in Sc, Y, and the heavy-rare-earth metals Tb, Dy, Ho, Er, Tm, and Lu

    International Nuclear Information System (INIS)

    Touborg, P.

    1977-01-01

    Experimental investigations of the magnetic poperties of dilute alloys of the rare-earth solutes Tb, Dy, Ho, Er, and Tm in the nonmagnetic hosts Lu, Y, and Sc have been performed. These measurements, which include and supplement earlier published results, have been analyzed and crystal-field parameters for all these 15 alloy systems deduced. The consistency of the parameters was confirmed by a variety of magnetic measurements, including neutron spectroscopy. Crystal-field parameters have also been derived for the ions in pure magnetic rare-earth metals and their alloys using the results for the dilute alloys supplemented with paramagnetic measurements up to high temperatures on the concentrated systems. Mean values and standard deviations of the higher-order crystal-field parameters for all Y and Lu alloys are B 40 /β = 6.8 +- 0.9 K, B 60 /γ = 13.6 +- 0.7 K, and B 66 /γ = (9.7 +- 1.1) B 60 /γ. These values: with the inaccuracies somewhat increased: are expected to be representative also for the magnetic rare-earth metals. For rare-earth ions in the Sc host the values B 40 /β = 9.9 +- 1.9 K, B 60 /γ = 19.8 +- 1.5 K, and B 66 /γ = (9.4 +- 0.9) B 60 /γ were deduced. B 20 /α is a host-sensitive parameter which has the average values of -102.7, -53.4, and 29.5 K for rare-earth ions in Y, Lu, and Sc, respectively. There is also evidence that this parameter varies with the solute. B 20 /α for ions in the pure magnetic rare-earth metals and their alloys shows a linear variation with c/a ratio characteristic of each ion. The results indicate a contribution from anisotropic exchange to the high-temperature paramagnetic anisotropy of approximately 20% for Tb, Dy, Ho, and Er, and approximately 10% for Tm

  13. Enhanced charging capability of lithium metal batteries based on lithium bis(trifluoromethanesulfonyl)imide-lithium bis(oxalato)borate dual-salt electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Xiang, Hongfa; Shi, Pengcheng; Bhattacharya, Priyanka; Chen, Xilin; Mei, Donghai; Bowden, Mark E.; Zheng, Jianming; Zhang, Ji-Guang; Xu, Wu

    2016-06-01

    Rechargeable lithium (Li) metal batteries with conventional LiPF6-carbonate electrolytes have been reported to fail quickly at charging current densities of about 1.0 mA cm-2 and above. In this work, we demonstrate the rapid charging capability of the Li||LiNi0.8Co0.15Al0.05O2 (NCA) cells enabled by a dual-salt electrolyte of LiTFSI-LiBOB in a carbonate solvent mixture. It is found that the thickness of solid electrolyte interphase (SEI) layer on Li metal anode largely increases with increasing charging current density. However, the cells using the LiTFSI-LiBOB dual-salt electrolyte significantly outperforms those using the LiPF6 electrolyte at high charging current densities. At the charging current density of 1.50 mA cm-2, the Li||NCA cells with the dual-salt electrolyte can still deliver a discharge capacity of 131 mAh g-1 and a capacity retention of 80% after 100 cycles, while those with the LiPF6 electrolyte start to show fast capacity fading after the 30th cycle and only exhibit a low capacity of 25 mAh g-1 and a low retention of 15% after 100 cycles. The reasons for the good chargeability and cycling stability of the cells using LiTFSI-LiBOB dual-salt electrolyte can be attributed to the good film-formation ability of the electrolyte on lithium metal anode and the highly conductive nature of the sulfur-rich interphase layer.

  14. Hyporheic Microbial Biofilms as Indicators of Heavy and Rare Earth Metals in the Clark Fork Basin, Montana

    Science.gov (United States)

    Barnhart, E. P.; Hornberger, M.; Hwang, C.; Dror, I.; Bouskill, N.; Short, T.; Cain, D.; Fields, M. W.

    2016-12-01

    The ability to effectively monitor the impact of hard rock mining activities on rivers and streams is a growing concern given the large number of active and abandoned mines in the western United States. One such example, the Clark Fork Basin (CFB), western Montana, was extensively mined for copper in the early 20th century: it is now one of largest U.S. EPA superfund sites. Microbial biofilms are at the base of the lotic food chain and may provide a useful biomonitoring tool for the assessment of metal toxicity due to their environmental ubiquity, rapidity of response to environmental perturbation, and importance in determining metal mobility. Hyporheic microbial biofilms from the CFB were sampled in 2014, concurrent with the USGS National Research Programs (NRP) long-term site monitoring of metals in bed sediment and aquatic benthic insects. Integration of the DNA sequencing results from the hyporheic biofilms with the sediment and insect metal concentrations correlated several bacterial phyla with metal contamination. For example, the genus Lysobacter was strongly associated with copper (Cu) bioaccumulation in the aquatic insect Hydropsyche. These results support previous studies identifying Lysobacter as a bacterial genus that is resistant to Cu ions. Our analysis is the first to indicate that specific microorganisms can act as biomarkers of Cu contamination in rivers. Moreover, our work demonstrates that changes at the microbial community level in the hyporheic zone can be coupled to observed perturbations across higher trophic levels. In 2015, extensive remediation occurred at several of the sites sampled in 2014, providing an excellent opportunity to revisit the sites and examine the temporal variability of identified biomarkers and the short-term effectiveness of remediation. In addition, samples were analyzed for rare earth metals, of which little is known, and could provide additional insight into other metals that change the microbial community structure.

  15. Precious metals and rare earth elements in municipal solid waste--sources and fate in a Swiss incineration plant.

    Science.gov (United States)

    Morf, Leo S; Gloor, Rolf; Haag, Olaf; Haupt, Melanie; Skutan, Stefan; Di Lorenzo, Fabian; Böni, Daniel

    2013-03-01

    In Switzerland many kinds of waste, e.g. paper, metals, electrical and electronic equipment are separately collected and recycled to a large extent. The residual amount of municipal solid waste (MSW) has to be thermally treated before final disposal. Efforts to recover valuable metals from incineration residues have recently increased. However, the resource potential of critical elements in the waste input (sources) and their partitioning into recyclable fractions and residues (fate) is unknown. Therefore, a substance flow analysis (SFA) for 31 elements including precious metals (Au, Ag), platinum metal group elements (Pt, Rh) and rare earth elements (La, Ce, etc.) has been conducted in a solid waste incinerator (SWI) with a state-of-the-art bottom ash treatment according to the Thermo-Re® concept. The SFA allowed the determination of the element partitioning in the SWI, as well as the elemental composition of the MSW by indirect analysis. The results show that the waste-input contains substantial quantities of precious metals, such as 0.4 ± 0.2mg/kg Au and 5.3 ± 0.7 mg/kg Ag. Many of the valuable substances, such as Au and Ag are enriched in specific outputs (e.g. non-ferrous metal fractions) and are therefore recoverable. As the precious metal content in MSW is expected to rise due to its increasing application in complex consumer products, the results of this study are essential for the improvement of resource recovery in the Thermo-Re® process. Copyright © 2012 Elsevier Ltd. All rights reserved.

  16. Half-metallic properties of the (1 1 0) surface of alkali earth metal monosilicides in the zinc blende phase

    International Nuclear Information System (INIS)

    Bialek, B; Lee, J I

    2011-01-01

    An all electron ab initio method was employed to study the electronic and magnetic properties of the (1 1 0) surface of alkaline-earth metal silicides: CaSi, SrSi and BaSi, in the zinc blende structure. The three surfaces are found to conserve the half-metallic properties of their bulk structures with a wide semiconducting energy gap in the spin-up channel. Half-metallic energy gap at the surfaces is small. In the CaSi surface it is of the order of k B T, which indicates that in the CaSi (1 1 0) a transition to a metallic state is possible due to temperature fluctuations. At the same time, the CaSi surface exhibits the strongest magnetic properties with 0.91 μ B magnetic moment on the Si atom in the topmost layer and 0.21 μ B magnetic moment on the Ca atom. In each of the three surfaces we observe a reduction of magnetic moments on the atoms in the subsurface layer and the enhancement of the magnetic moment on the atoms in the topmost layer, as compared with the properties of atoms in the bulk. An analysis of the calculated total and atom projected densities of states leads to a conclusion that the surface effects in the structures are short-range phenomena

  17. Effect of Destined High-Pressure Torsion on the Structure and Mechanical Properties of Rare Earth-Based Metallic Glasses

    Science.gov (United States)

    Zhao, W.; Cheng, H.; Jiang, X.; Wu, M. L.; Li, G.

    2018-03-01

    Changes in the atomic structure and mechanical properties of rare earth-based metallic glasses caused by destined high-pressure torsion (HPT) were studied by X-ray diffraction synchrotron radiation and nanoindentation. Results showed that destined HPT improved nanohardness and wear resistance, which indicated the significant contributions of this technique. The diffraction patterns showed that the contents of pairs between solvent and solute atoms with a large negative mixing enthalpy increased, whereas those of pairs between solvent atoms and between solute atoms decreased after destined HPT. Thus, the process was improved by increasing the proportion of high-intensity pairs between solvent and solute atoms.

  18. Antimicrobial Effects of Sodium Fluoride, Xylitol and Metals Salts on in Vitro Growth Inhibition, Acid Production and Ultrastructure of Streptococcus mutans

    International Nuclear Information System (INIS)

    El-Mongy, T.M.; Abd EI-Aziz, A.B.

    2009-01-01

    This study aimed to evaluate the effects of sodium fluoride (NaF), dietary sugars, sugar alcohols (xylitol and sorbitol) and different metals salts either separately or in combination, by different concentrations at different ph, on the growth inhibition, acid production and ultra structure of Streptococcus mutans. NaF was more effective at low ph, when NaF was added to actively growing Streptococcus mutans broth culture, the growth rate was unaffected by 75 ppm F-, slowed by 150 ppm F-, and immediately arrested by 300 or 600 ppm F-. On the other hand, the best effect of xylitol was at high ph. The effect of xylitol was more marked in the presence of NaF as the acid production was inhibited and the ph did not fall to 5.0. The response of Streptococcus mutans to metals salts was typical of this organism's response to a number of trace metals above optimum concentrations of which may be inhibitory. Synergistic effect observed by addition of metals salts by concentration ranged from 0.2 to 5.0 mML-1, 300 ppm NaF and 5% xylitol. This formula can work at any ph value and causes no drop of the broth culture ph to below 5.0 which is the optimal ph for growth and multiplication of Streptococcus mutans, so this formula worked as ph buffer regulation and growth inhibition for S. mutans. Low concentration of this combined formula after 5 min only at 5.0 and 7.0 ph values caused effective complete destruction of the bacterial viable cells and this effect was observed clearly by Electron Microscope photo graph

  19. Proceedings of the sixth international workshop on rare earth-cobalt permanent magnets and their applications, August 31 - September 2, 1982, and third international symposium on magnetic anisotropy and coercivity in rare earth-transition metal alloys, September 3, 1982

    International Nuclear Information System (INIS)

    Fidler, J.

    1982-01-01

    The first part (workshop) is concerned specifically with applications of rare earth-cobalt permanent magnets. The session headings are 1) electro-mechanical applications 2) electronic and miscellaneous applications 3) magneto-mechanical applications plus workshop on measurement methods 4) new materials and processes 5) industrial applications of REPM and future aspects. The second part (symposium) is concerned with physical properties of specific rare earth-transition metal alloys. (G.Q.)

  20. Adsorption of di-2-ethylhexylphosphoric acid from toluene the interface with inorganic salt aqueous solutions

    International Nuclear Information System (INIS)

    Fajnshtejn, E.V.; Popov, A.N.

    1990-01-01

    Interfacial tension in the system toluene solution of di-2-ethylhexylphosphoric acid HDEHP-aqueous solutions of inorganic salts has been measured by the drop volume method. The ion-exchange constants in the monolayers formed by HDEHP and alkaline-earth metals have been measured

  1. Kinetics and mechanism of the hydridation of uranium and rare-earth metals

    International Nuclear Information System (INIS)

    Bloch, J.

    1989-07-01

    The purpose of this work was to study the rate and the mechanism of the hydridation reaction of uranium and the lanthanide metals. Surface sensitive analysis was used to study the reaction of the metal surface with residual gases of the high vacuum atmosphere. The initial stages of the uranium-hydrogen reaction, taking place on a polished metal surface, were investigated utilizing a hot-stage microscope equipped with TV camera and a video-recorder. The characteristics of formation and advance mechanism of hydride phase in bulk uranium and lanthanide metals were studied utilizing metallographic examination of partially hydrided thin foil samples at different stages of the reaction. The interface velocity of the hydride in uranium was measured as a function of pressure and temprature in a constant volume system. A probabilistic kinetic model for a gas-solid interaction, controlled by a phase transformation step, was developed and applied to the hydridation of uranium and gadolinium

  2. A novel molten-salt electrochemical cell for investigating the reduction of uranium dioxide to uranium metal by lithium using in situ synchrotron radiation.

    Science.gov (United States)

    Brown, Leon D; Abdulaziz, Rema; Jervis, Rhodri; Bharath, Vidal; Mason, Thomas J; Atwood, Robert C; Reinhard, Christina; Connor, Leigh D; Inman, Douglas; Brett, Daniel J L; Shearing, Paul R

    2017-03-01

    A novel electrochemical cell has been designed and built to allow for in situ energy-dispersive X-ray diffraction measurements to be made during reduction of UO 2 to U metal in LiCl-KCl at 500°C. The electrochemical cell contains a recessed well at the bottom of the cell into which the working electrode sits, reducing the beam path for the X-rays through the molten-salt and maximizing the signal-to-noise ratio from the sample. Lithium metal was electrodeposited onto the UO 2 working electrode by exposing the working electrode to more negative potentials than the Li deposition potential of the LiCl-KCl eutectic electrolyte. The Li metal acts as a reducing agent for the chemical reduction of UO 2 to U, which appears to proceed to completion. All phases were fitted using Le Bail refinement. The cell is expected to be widely applicable to many studies involving molten-salt systems.

  3. Effect of Rare Earth Metals, Sr, and Ti Addition on the Microstructural Characterization of A413.1 Alloy

    Directory of Open Access Journals (Sweden)

    M. G. Mahmoud

    2017-01-01

    Full Text Available The present work was performed on A413.1 alloy containing 0.2–1.5 wt% rare earth metals (lanthanum or cerium, 0.05–0.15% Ti, and 0–0.02 wt% Sr. These elements were either added individually or combined. Thermal analysis, image analysis, and electron probe microanalysis were the main techniques employed in the present study. The results show that the use of the depression in the eutectic temperature as a function of alloy modification cannot be applied in the case when the alloy is treated with rare earth metals. Increasing the concentration of RE increases the solidification zone especially in Sr-modified alloys leading to poor feeding ability. This observation is more prominent in the case of Ce addition. Depending upon the amount of added Ti, two RE based intermetallics can be formed: (i a white phase, mainly platelet-like (approximately 2.5 μm thick, that is rich in RE, Si, Cu, and Al and (ii a second phase made up of mainly grey sludge particles (star-like branching in different directions. The grey phase is rich in Ti with some RE (almost 20% of that in the white phase with traces of Si and Cu. There is a strong interaction between RE and Sr leading to a reduction in the efficiency of Sr as a eutectic Si modifier causing particle demodification.

  4. Effect of metal cation replacement on the electronic structure of metalorganic halide perovskites: Replacement of lead with alkaline-earth metals

    Science.gov (United States)

    Pazoki, Meysam; Jacobsson, T. Jesper; Hagfeldt, Anders; Boschloo, Gerrit; Edvinsson, Tomas

    2016-04-01

    Organic and inorganic lead halogen perovskites, and in particular, C H3N H3Pb I3 , have during the last years emerged as a class of highly efficient solar cell materials. Herein we introduce metalorganic halogen perovskite materials for energy-relevant applications based on alkaline-earth metals. Based on the classical notion of Goldschmidt's rules and quantum mechanical considerations, the three alkaline-earth metals, Ca, Sr, and Ba, are shown to be able to exchange lead in the perovskite structure. The three alkaline-earth perovskites, C H3N H3Ca I3,C H3N H3Sr I3 , and C H3N H3Ba I3 , as well as the reference compound, C H3N H3Pb I3 , are in this paper investigated with density functional theory (DFT) calculations, which predict these compounds to exist as stable perovskite materials, and their electronic properties are explored. A detailed analysis of the projected molecular orbital density of states and electronic band structure from DFT calculations were used for interpretation of the band-gap variations in these materials and for estimation of the effective masses of the electrons and holes. Neglecting spin-orbit effects, the band gap of MACa I3,MASr I3 , and MABa I3 were estimated to be 2.95, 3.6, and 3.3 eV, respectively, showing the relative change expected for metal cation exchange. The shifts in the conduction band (CB) edges for the alkaline-earth perovskites were quantified using scalar relativistic DFT calculations and tight-binding analysis, and were compared to the situation in the more extensively studied lead halide perovskite, C H3N H3Pb I3 , where the change in the work function of the metal is the single most important factor in tuning the CB edge and band gap. The results show that alkaline-earth-based organometallic perovskites will not work as an efficient light absorber in photovoltaic applications but instead could be applicable as charge-selective contact materials. The rather high CB edge and the wide band gap together with the large

  5. Interactions of a beta-dipeptide with monovalent metal cations: crystal structures of (anthranoyl)anthranilic acid and its lithium, sodium and thallium salts.

    Science.gov (United States)

    Wiesbrock, Frank; Schmidbaur, Hubert

    2004-03-01

    X-ray crystal structure analyses have been performed on the beta-dipeptide (anthranoyl)anthranilic acid [HAnthAnthOH] and its lithium, sodium and thallium salts [HAnthAnthOM] to give a first set of data for this representative model ligand. Crystals of the beta-dipeptide are orthorhombic, space group Pca2(1). The unit cell contains two molecules of (anthranoyl)anthranilic acid which form a dimer via hydrogen bonds. The components of the beta-dipeptide are rotated into the trans-conformation which allows for internal hydrogen bonds. The pKS value of (anthranoyl)anthranilic acid (9.80+/-0.14) shows a slight decrease as compared to anthranilic acid; the metal salts can therefore be prepared by direct neutralization of the beta-dipeptide with metal hydroxides or carbonates. The alkali compounds crystallize as the trihydrates [HAnthAnthOM(H2O)3, M=Li, Na] in the triclinic space group p1. Both metal ions show a clear preference for water molecules over the (anthranoyl)anthranilate anions as ligands in their coordination spheres. As a consequence, the [HAnthAnthO]- anions are only partially involved in metal complexation. The cell plots of both compounds exhibit a stacking with an alternation of oppositely charged layers. The negatively charged layers are composed exclusively of (anthranoyl)anthranilate anions. The thallium compound crystallizes as the hemihydrate [HAnthAnthOTl(H2O)0.5] in the monoclinic space group C2/c. In the dinuclear units, the thallium ions accommodate one nitrogen and four oxygen atoms of the anions in their coordination sphere and in addition entertain weak Tl-arene contacts. In contrast to the alkali compounds, the water molecules are not involved in metal complexation, but contribute to a network of hydrogen bonding.

  6. Alkaline-earth metal phosphonocarboxylates: synthesis, structures, chirality, and luminescence properties

    Czech Academy of Sciences Publication Activity Database

    Zima, Vítězslav; Raja, D. S.; Lee, Y. S.; Chang, T. G.; Wu, Ch. Y.; Hu, Ch. Ch.; Lee, K. R.; Lai, J. Y.; Yeh, J. M.; Lin, Ch. H.

    2013-01-01

    Roč. 42, č. 43 (2013), s. 15332-15342 ISSN 1477-9226 Grant - others:AV ČR(CZ) M200501202 Program:M Institutional support: RVO:61389013 Keywords : coordination polymers * phosphonates * alkaline-earth Subject RIV: CA - Inorganic Chemistry Impact factor: 4.097, year: 2013

  7. Post-synthetic modification of porphyrin-encapsulating metal-organic materials by cooperative addition of inorganic salts to enhance CO 2/CH 4 selectivity

    KAUST Repository

    Zhang, ZhenJie

    2012-08-21

    Keeping MOM: Reaction of biphenyl-3,4\\',5-tricarboxylate and Cd(NO 3) 2 in the presence of meso-tetra(N-methyl-4-pyridyl) porphine tetratosylate afforded porph@MOM-11, a microporous metal-organic material (MOM) that encapsulates cationic porphyrins and solvent in alternating open channels. Porph@MOM-11 has cation and anion binding sites that facilitate cooperative addition of inorganic salts (such as M +Cl -) in a stoichiometric fashion. © 2012 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. THE INFLUENCE OF ANION NATURE OF ALKALINE METAL SALT ON SPECTRAL-LUMINESCENT PROPERTIES OF F-S-HETERONUCLEAR COMPLEXES ON THE BASE OF CROWN-PORPHYRINS

    Directory of Open Access Journals (Sweden)

    N. V. Rusakova

    2016-04-01

    Full Text Available The heteronuclear complexes on the base of meso-tetra-crown-ether substituted porphyrins of «sandwich»-type which two ytterbium ions coordinated with porphyrin macrocycles, and four cations of alkaline metals (Na, K, Cs situated between the cavities of benzo-12-crown-4-, benzo-15-crown-5- and benzo-18-crown-6-ethers, respectively, were obtained. The influence of anion nature of salts (bromide, nitrate, thiocyanate on 4f-luminescence of Yb8+ ions in these complexes were analyzed.

  9. A Comparative Study of Mn/Co Binary Metal Catalysts Supported on Two Commercial Diatomaceous Earths for Oxidation of Benzene

    Directory of Open Access Journals (Sweden)

    Marco Tomatis

    2018-03-01

    Full Text Available Two commercial diatomaceous earths were used as supports for the preparation of Mn/Co binary metal catalysts at different metal loads (5 to 10 wt % Mn and 5 to 15 wt % Co by incipient wetness deposition. The activity of the prepared catalysts towards the complete oxidation of benzene to CO2 and water was investigated between 100 and 400 °C. Raw supports and synthesized catalysts were characterized by XRD, N2 physisorption, SEM-EDS, H2-TPR, and TPD. The purification treatment of food-grade diatomite significantly affected the crystallinity of this support while reducing its specific surface area (SSA. A loss of SSA, associated with the increase in the metal load, was observed on samples prepared on natural diatomite, while the opposite trend occurred with food-grade diatomite-supported catalysts. Metal nanoparticles of around 50 nm diameter were observed on the catalysts’ surface by SEM analysis. EDS analysis confirmed the uniform deposition of the active phases on the support’s surface. A larger H2 consumption was found by TPR analysis of natural diatomite-based samples in comparison to those prepared at the same metal load on food-grade diatomite. During the catalytic oxidation experiment, over 90% conversion of benzene were achieved at a reaction temperature of 225 °C by all of the prepared samples. In addition, the formation of coke during the oxidation tests was demonstrated by TGA analysis and the soluble fraction of the produced coke was characterized by GC-MS.

  10. The Study of Anti-/Pro-Oxidant, Lipophilic, Microbial and Spectroscopic Properties of New Alkali Metal Salts of 5-O-Caffeoylquinic Acid

    Science.gov (United States)

    Kalinowska, Monika; Bajko, Ewelina; Matejczyk, Marzena; Kaczyński, Piotr; Łozowicka, Bożena; Lewandowski, Włodzimierz

    2018-01-01

    Lithium, sodium, potassium, rubidium and caesium salts of 5-O-caffeoylquinic acid (chlorogenic acid, 5-CQA) were synthesized and described by FT-IR (infrared spectroscopy), FT-Raman (Raman spectroscopy), UV (UV absorption spectroscopy), 1H (400.15 MHz), 13C (100.63 MHz) NMR (nuclear magnetic resonance spectroscopy). The quantum–chemical calculations at the B3LYP/6-311++G** level were done in order to obtain the optimal structures, IR spectra, NBO (natural bond orbital) atomic charges, HOMO (highest occupied molecular orbital) and LUMO (lowest unoccupied molecular orbital) orbitals and chemical reactivity parameters for 5-CQA and Li, Na and K 5-CQAs (chlorogenates). The DPPH (α, α-diphenyl-β-picrylhydrazyl) and FRAP (ferric reducing antioxidant power) assays were used for the preliminary estimation of the antioxidant properties of alkali metal chlorogenates and chlorogenic acid. In the DPPH assay the EC50 parameter were equal to 7.39 μM for 5-CQA and was in the range of 4.50–5.89 μM for salts. The FRAP values for two different concentrations (5 and 2.5 μM) of the studied compounds were respectively 114.22 and 72.53 μM Fe2+ for 5-CQA, whereas for salts they were 106.92–141.13 and 78.93–132.00 μM Fe2+. The 5-CQA and its alkali metal salts possess higher antioxidant properties than commonly applied antioxidants (BHA, BHT, l-ascorbic acid). The pro-oxidant action of these compounds on trolox oxidation was studied in the range of their concentration 0.05–0.35 μM. The lipophilicity (logkw) of chlorogenates and chlorogenic acid was determined by RP-HPLC (reverse phase—high performance liquid chromatography) using five different columns (C8, PHE (phenyl), CN (cyano), C18, IAM (immobilized artificial membrane)). The compounds were screened for their in vitro antibacterial activity against E. coli, Bacillus sp., Staphylococcus sp., Streptococcus pyogenes and antifungal activity against Candida sp. The 5-CQA possessed lower antibacterial (minimal

  11. The Study of Anti-/Pro-Oxidant, Lipophilic, Microbial and Spectroscopic Properties of New Alkali Metal Salts of 5-O-Caffeoylquinic Acid

    Directory of Open Access Journals (Sweden)

    Monika Kalinowska

    2018-02-01

    Full Text Available Lithium, sodium, potassium, rubidium and caesium salts of 5-O-caffeoylquinic acid (chlorogenic acid, 5-CQA were synthesized and described by FT-IR (infrared spectroscopy, FT-Raman (Raman spectroscopy, UV (UV absorption spectroscopy, 1H (400.15 MHz, 13C (100.63 MHz NMR (nuclear magnetic resonance spectroscopy. The quantum–chemical calculations at the B3LYP/6-311++G** level were done in order to obtain the optimal structures, IR spectra, NBO (natural bond orbital atomic charges, HOMO (highest occupied molecular orbital and LUMO (lowest unoccupied molecular orbital orbitals and chemical reactivity parameters for 5-CQA and Li, Na and K 5-CQAs (chlorogenates. The DPPH (α, α-diphenyl-β-picrylhydrazyl and FRAP (ferric reducing antioxidant power assays were used for the preliminary estimation of the antioxidant properties of alkali metal chlorogenates and chlorogenic acid. In the DPPH assay the EC50 parameter were equal to 7.39 μM for 5-CQA and was in the range of 4.50–5.89 μM for salts. The FRAP values for two different concentrations (5 and 2.5 μM of the studied compounds were respectively 114.22 and 72.53 μM Fe2+ for 5-CQA, whereas for salts they were 106.92–141.13 and 78.93–132.00 μM Fe2+. The 5-CQA and its alkali metal salts possess higher antioxidant properties than commonly applied antioxidants (BHA, BHT, l-ascorbic acid. The pro-oxidant action of these compounds on trolox oxidation was studied in the range of their concentration 0.05–0.35 μM. The lipophilicity (logkw of chlorogenates and chlorogenic acid was determined by RP-HPLC (reverse phase—high performance liquid chromatography using five different columns (C8, PHE (phenyl, CN (cyano, C18, IAM (immobilized artificial membrane. The compounds were screened for their in vitro antibacterial activity against E. coli, Bacillus sp., Staphylococcus sp., Streptococcus pyogenes and antifungal activity against Candida sp. The 5-CQA possessed lower antibacterial (minimal inhibitory

  12. Contribution to the study of diffusion in rare earth metals and actinides

    International Nuclear Information System (INIS)

    Marbach, Gabriel.

    1978-07-01

    This work describes several experiments carried out in order to understand the process of self diffusion in rare earth and actinides (self diffusion of body centered cubic γ neptunium, diffusion of gadolinium in body centered delta cerium, measurement of the activation volume of face centered cubic γ cerium). The unstable electronic structure of some elements cannot be correlate with anomalous diffusion properties. In fact the diffusion parameters of neptunium and plutonium are similar (high diffusivity and low activation energy) whereas the electronic structure of neptunium is stable and that of plutonium is temperature dependent. The negative activation volume of the body centered cubic phases of plutonium and cerium does not indicate a particular diffusion mechanism since self diffusion is faster under pressure in face centered cubic γ cerium where a vacancy mechanism is assumed according to earlier results. The vacancy mechanism is the most probable diffusion process in the body centered cubic and compact phases of rare earths and actinides [fr

  13. Facile Coordination-Precipitation Route to Insoluble Metal Roussin's Black Salts for NIR-Responsive Release of NO for Anti-Metastasis.

    Science.gov (United States)

    Chen, Lijuan; He, Qianjun; Lei, Minyi; Xiong, Liwei; Shi, Kun; Tan, Liwei; Jin, Zhaokui; Wang, Tianfu; Qian, Zhiyong

    2017-10-25

    A facile and general coordination-precipitation method is developed to synthesize insoluble metal Roussin's black salts (Me-RBSs) as a new type of NIR-responsive NORMs. The weak-field ligand coordination of metal + -RBS - brings a NIR absorption effect of Me-RBSs, and further gives rise to the NIR adsorption-dependent NIR-responsive NO release profile. Intratumoral NIR-responsive release of NO effectively inhibits the growth and metastasis of the metastatic breast cancer. Aqueous insolubility of Me-RBSs ensures lower cytotoxicity and higher thermostability compared with traditional soluble RBSs. This work establishes a new class of NIR-sensitive NO donors, and may spark new inspiration for designing intelligent gas-releasing molecules.

  14. A general salt-templating method to fabricate vertically aligned graphitic carbon nanosheets and their metal carbide hybrids for superior lithium ion batteries and water splitting.

    Science.gov (United States)

    Zhu, Jixin; Sakaushi, Ken; Clavel, Guylhaine; Shalom, Menny; Antonietti, Markus; Fellinger, Tim-Patrick

    2015-04-29

    The synthesis of vertically aligned functional graphitic carbon nanosheets (CNS) is challenging. Herein, we demonstrate a general approach for the fabrication of vertically aligned CNS and metal carbide@CNS composites via a facile salt templating induced self-assembly. The resulting vertically aligned CNS and metal carbide@CNS structures possess ultrathin walls, good electrical conductivity, strong adhesion, excellent structural robustness, and small particle size. In electrochemical energy conversion and storage such unique features are favorable for providing efficient mass transport as well as a large and accessible electroactive surface. The materials were tested as electrodes in a lithium ion battery and in electrochemical water splitting. The vertically aligned nanosheets exhibit remarkable lithium ion storage properties and, concurrently, excellent properties as electrocatalysts for hydrogen evolution.

  15. Surface shift of the occupied and unoccupied 4f levels of the rare-earth metals

    DEFF Research Database (Denmark)

    Aldén, Magnus; Johansson, Börje; Skriver, Hans Lomholt

    1995-01-01

    The surface energy shifts of the occupied and unoccupied 4f levels for the lanthanide metals have been calculated from first principles by means of a Green’s-function technique within the tight-binding linear muffin-tin orbitals method. We use the concept of complete screening to identify the occ...

  16. Electrolyte salts for nonaqueous electrolytes

    Science.gov (United States)

    Amine, Khalil; Zhang, Zhengcheng; Chen, Zonghai

    2012-10-09

    Metal complex salts may be used in lithium ion batteries. Such metal complex salts not only perform as an electrolyte salt in a lithium ion batteries with high solubility and conductivity, but also can act as redox shuttles that provide overcharge protection of individual cells in a battery pack and/or as electrolyte additives to provide other mechanisms to provide overcharge protection to lithium ion batteries. The metal complex salts have at least one aromatic ring. The aromatic moiety may be reversibly oxidized/reduced at a potential slightly higher than the working potential of the positive electrode in the lithium ion battery. The metal complex salts may also be known as overcharge protection salts.

  17. Facile and scalable synthesis of Ti5Si3 nanoparticles in molten salts for metal-matrix nanocomposites.

    Science.gov (United States)

    Estruga, Marc; Girard, Steven N; Ding, Qi; Chen, Lianyi; Li, Xiaochun; Jin, Song

    2014-02-11

    We report a novel synthesis of Ti5Si3 nanoparticles (NPs) via the magnesio-reduction of TiO2 NPs and SiO2 in eutectic LiCl-KCl molten salts at 700 °C. The Ti5Si3 particle size (∼25 nm) is confined to the nanoscale due to the partial dissolution of Mg and silica in the molten salts and a subsequent heterogeneous reduction on the surface of the TiO2 NPs.

  18. Oxidation behavior of Cr(III) during thermal treatment of chromium hydroxide in the presence of alkali and alkaline earth metal chlorides.

    Science.gov (United States)

    Mao, Linqiang; Gao, Bingying; Deng, Ning; Liu, Lu; Cui, Hao

    2016-02-01

    The oxidation behavior of Cr(III) during the thermal treatment of chromium hydroxide in the presence of alkali and alkaline earth metal chlorides (NaCl, KCl, MgCl2, and CaCl2) was investigated. The amounts of Cr(III) oxidized at various temperatures and heating times were determined, and the Cr-containing species in the residues were characterized. During the transformation of chromium hydroxide to Cr2O3 at 300 °C approximately 5% of the Cr(III) was oxidized to form intermediate compounds containing Cr(VI) (i.e., CrO3), but these intermediates were reduced to Cr2O3 when the temperature was above 400 °C. Alkali and alkaline earth metals significantly promoted the oxidation of Cr(III) during the thermal drying process. Two pathways were involved in the influences the alkali and alkaline earth metals had on the formation of Cr(VI). In pathway I, the alkali and alkaline earth metals were found to act as electron transfer agents and to interfere with the dehydration process, causing more intermediate Cr(VI)-containing compounds (which were identified as being CrO3 and Cr5O12) to be formed. The reduction of intermediate compounds to Cr2O3 was also found to be hindered in pathway I. In pathway II, the alkali and alkaline earth metals were found to contribute to the oxidation of Cr(III) to form chromates. The results showed that the presence of alkali and alkaline earth metals significantly increases the degree to which Cr(III) is oxidized during the thermal drying of chromium-containing sludge. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Study on the extraction of rare earth elements in liquid bismuth

    International Nuclear Information System (INIS)

    Harada, M.; Adachi, M.; Kai, Y.; Koike, K.

    1987-01-01

    Three factors, which are important for the extraction of rare earth elements in liquid bismuth - molten salt system, were studied, i. e., the equilibrium distribution of neodymium, samarium and bismuth between molten LiCl - liquid Bi-Li alloys, the extraction rate of rare earths, and the characteristics of the extractor with drop dispersion. The rare earth elements were extracted through redox reactions. In high range of Li-mole fraction in the alloy phase, X Li , the distribution of neodymium and bismuth in the salt phase markedly increased as X Li increased. The anomalous increase is attributed to the formation of the compound comprised of Nd, Li, Bi and oxygen in the salt phase. The redox reaction processes were very fast and the extraction rates for rare earths are controlled by the diffusion processes of the solute and the metallic lithium. The process for the formation of liquid metal drops in the continuous phase is predictable from semiempirical correlations reported for aqueous solution - organic solvent systems. The height of droplet bed being accumulated on drop settling portion is predictable from the coalescence time of single drop to a flat metal interface. The coalescence of metal drop to clean interface was very fast. The extractor type of liquid metal dispersion in molten salt is suitable for the extraction process in the fuel reprocessing of MSR or MSBR. (author)

  20. Synchrotron Diffraction Studies of Spontaneous Magnetostriction in Rare Earth Transition Metal Compounds

    International Nuclear Information System (INIS)

    Ning Yang

    2004-01-01

    Thermal expansion anomalies of R 2 Fe 14 B and R 2 Fe 17 C x (x = 0,2) (R Y, Nd, Gd, Tb, Er) stoichiometric compounds are studied with high-energy synchrotron X-ray powder diffraction using Debye-Schemer geometry in temperature range 10K to 1000K. Large spontaneous magnetostriction up to their Curie temperatures (T c ) is observed. The a-axes show relatively larger invar effects than c-axes in the R 2 Fe 14 B compounds whereas the R 2 Fe 17 C x show the contrary anisotropies. The iron sub-lattice is shown to dominate the spontaneous magnetostriction of the compounds. The contribution of the rare earth sublattice is roughly proportional to the spin magnetic moment of the rare earth in the R 2 Fe 14 B compounds but in R 2 Fe 17 C x , the rare earth sub-lattice contribution appears more likely to be dominated by the local bonding. The calculation of spontaneous magnetostrain of bonds shows that the bonds associated with Fe(j2) sites in R 2 Fe 14 B and the dumbbell sites in R 2 Fe 17 C x have larger values, which is strongly related to their largest magnetic moment and Wigner-Seitz atomic cell volume. The roles of the carbon atoms in increasing the Curie temperatures of the R 2 Fe 17 compounds are attributed to the increased separation of Fe hexagons. The R 2 Fe 17 and R 2 Fe 14 B phases with magnetic rare earth ions also show anisotropies of thermal expansion above T c . For R 2 Fe 17 and R 2 Fe 14 B the a a /a c > 1 whereas the anisotropy is reversed with the interstitial carbon in R 2 Fe 17 . The average bond magnetostrain is shown to be a possible predictor of the magnetic moment of Fe sites in the compounds. Both of the theoretical and phenomenological models on spontaneous magnetostriction are discussed and a Landau model on the spontaneous magnetostriction is proposed

  1. Calculation of crystal-field parameters for rare-earth noble metal alloys

    Energy Technology Data Exchange (ETDEWEB)

    Steinbeck, L. [MPG Research Group `Electron Systems`, Department of Physics, University of Technology, Mommsenstr. 13, D-01062, Dresden (Germany); Richter, M. [MPG Research Group `Electron Systems`, Department of Physics, University of Technology, Mommsenstr. 13, D-01062, Dresden (Germany); Eschrig, H. [MPG Research Group `Electron Systems`, Department of Physics, University of Technology, Mommsenstr. 13, D-01062, Dresden (Germany); Nitzsche, U. [MPG Research Group `Electron Systems`, Department of Physics, University of Technology, Mommsenstr. 13, D-01062, Dresden (Germany)

    1995-02-09

    The crystal-field (CF) parameters for 4f electrons of a series of rare-earth impurities in Ag and Au have been evaluated from first-principles density functional calculations of the charge distribution which are based on an optimized LCAO scheme. The localized 4f states are treated as `open core shell`. By including the self-interaction correction for the 4f states, artificial constraints on the 4f charge density employed in earlier density functional CF calculations are avoided. The calculated parameters are compared with recent neutron scattering data. ((orig.)).

  2. Study of water nature in some crystallohydrates of pentasubstituted alkali metal salts of borotungstic acid using thermochemical method

    International Nuclear Information System (INIS)

    Kosmodem'yanskaya, G.V.; Sadykova, M.M.; Spitsyn, V.I.

    1977-01-01

    Kinetics of the dehydration process has been studied and heat of dehydration has been determined for salts 2.5Li 2 O x 0.5B 2 O 3 x 12.0WO 3 x 28.5H 2 O; 2.5Na 2 Ox0.5B 2 O 3 x 12.0WO 3 x 17.5H 2 O; 2.5K 2 O x 0.5B 2 O 3 x12.0WO 3 x 16.5H 2 O; 2.5Cs 2 O x 0.5B 2 O 3 x 12.0WO 3 x6.7H 2 O. Dehydration has been conducted in vacuum at 25-50 deg C. The study of the dehydration process has been performed thermochemically in a differential calorimeter. It has been shown that heat of dehydration depends on the nature of the cation. Lithium salt with a cation of a small radius has the highest heat of dehydration (6.4+-0.2 kcal/mol H 2 O). Cesium salt is dehydrated almost completely. A considerable part of water in crystallohydrates has a salting character. Kinetics of the dehydration process is described by the equation of the monomolecular reaction

  3. New ternary transition metal borides containing uranium and rare earth elements

    International Nuclear Information System (INIS)

    Rogl, P.; Delong, L.

    1983-01-01

    The new ternary actinide metal diborides U 2 MoB 6 , U 2 ReB 6 , U 2 OsB 6 , URuB 4 and UOsB 4 were prepared and found to crystallize with either the Y 2 ReB 6 or the ThMoB 4 type of structure. LuRuB 4 and LuOsB 4 crystallize with the YCrB 4 type of structure. In a ternary series of solid solutions YRh 3 Bsub(1-x) (0 0 C), boron was found to stabilize a Cu 3 Au type of structure. The superconductivity of the new uranium compounds and of a series of ternary transition metal borides was investigated; no superconductivity was observed for temperatures as low at 1.3-1.5 K. The cubic perovskite or filled Cu 3 Au structure is discussed as a type which is very unfavorable for the occurrence of superconductivity. (Auth.)

  4. Microwave-Assisted Adsorptive Desulfurization of Model Diesel Fuel Using Synthesized Microporous Rare Earth Metal-Doped Zeolite Y

    Directory of Open Access Journals (Sweden)

    N. Salahudeen

    2015-06-01

    Full Text Available The microwave-assisted adsorptive desulfurization of model fuel (thiophene in n-heptane was investigated using a synthesized rare earth metal-doped zeolite Y (RE Y. Crystallinity of the synthesized zeolite was 89.5%, the silicon/aluminium (Si/Al molar ratio was 5.2, the Brunauer–Emmett–Teller (BET surface area was 980.9 m2/g, and the pore volume and diameter was 0.3494 cm3/g and 1.425 nm, respectively. The results showed that the microwave reactor could be used to enhance the adsorptive desulfurization process with best efficiency of 75% at reaction conditions of 100 °C and 15 minutes. The high desulfurization effect was likely due to the higher efficiency impact of microwave energy in the interaction between sulfur in thiophene and HO-La(OSiAl.

  5. Heavy-metal extraction from sewage sludge using phosphorous-based salts: optimization process with Na2H2P2O7.

    Science.gov (United States)

    Navarro-González, Milagros; Ortega-López, Vanesa; Lópéz-Fernández, Juana I; Amo-Salas, Mariano; González-Carcedo, Salvador

    2017-09-01

    Land application is one of the important disposal alternatives for sewage sludge, but availability of potential toxic metals often restricts its uses. Three phosphorous-based salts (Na 2 H 2 P 2 O 7 , K 4 P 2 O 7 , KH 2 PO 4 ) were studied as potential metal extractants. The conclusions of the research were that greater extractive efficiency is achieved through a 30-min process of vertical shaking with disodium diacid pyrophosphate - Na 2 H 2 P 2 O 7 - at a concentration of 0.2 M at pH 2. Alternatively, the optimized process with oscillating shaking equipment would require 60 min. In both cases the average of set of extracted metals is around 50%. A second extraction process with potassium pyrophosphate - K 4 P 2 O 7 at pH 6 achieved the reduction of further total amounts of metal, upper 65% with respect to the initial content. In this way the sludge could be used in land applications, with restrictions on each soil, according to the limit values specified in the future regulations.

  6. First-Principle Predictions of Electronic Properties and Half-Metallic Ferromagnetism in Vanadium-Doped Rock-Salt SrO

    Science.gov (United States)

    Berber, Mohamed; Doumi, Bendouma; Mokaddem, Allel; Mogulkoc, Yesim; Sayede, Adlane; Tadjer, Abdelkader

    2018-01-01

    We have used first-principle methods of density functional theory within the full potential linearized augmented plane wave scheme to investigate the electronic and magnetic properties of cubic rock-salt, SrO, doped with vanadium (V) impurity as Sr1- x V x O at various concentrations, x = 0.25, 0.5, and 0.75. We have found that the ferromagnetic state arrangement of Sr1- x V x O is more stable compared to the anti-ferromagnetic state configuration. The electronic structures have a half-metallic (HM) ferromagnetic (F) behavior for Sr0.75V0.25O and Sr0.5V0.5O. This feature results from the metallic and semiconducting natures of majority-spin and minority-spin bands, respectively. The HMF gap decreases with the increasing concentration of vanadium atoms due to the broadening of 3 d (V) levels in the gap, and hence the Sr0.25V0.75O becomes metallic ferromagnetic. The Sr0.75V0.25O revealed a large HM gap with spin polarization of 100%. The Sr1- x V x O compound at low concentrations seems a better candidate to explore the half-metallicity for practical spintronics applications.

  7. Cum grano salis - NAA of selected salts

    International Nuclear Information System (INIS)

    Steinhauser, G.; Sterba, J.H.; Poljanc, K.; Bichler, M.; Buchtela, K.

    2006-01-01

    The aim of this study was to investigate the trace element concentrations of salt samples from different regions, in particular Austria, Germany, Pakistan, Poland, Switzerland, and Ukraine. Investigated types of salt were Rock-, Sea-, Lake-, and Evaporated Salt. The main objective was to find out whether the consumption of salt can contribute significantly to the daily human requirements of trace elements. Therefore, trace element concentrations in the untreated samples were compared to those of specially treated samples, simulating digestive uptake using a simple model. Salt is a non-trivial matrix for Neutron Activation Analysis (NAA) because of very high background activities from 38 Cl and 24 Na, as well as the bremsstrahlung of 32 P (originating from 35 Cl(n,α) 32 P). Because of this fact, detection limits in salt are higher compared to other matrices. Nevertheless, several elements could be detected, namely Al, Ba, Br, (Ca), Ce, Cl, Co, Cr, Cs, Eu, Fe, Hf, La, Mn, Na, Rb, Sb, Sc, Sm, Sr, Ta, Tb, Th, and Zn, some of them only in single samples. In most samples the concentrations of trace elements in salt were too low to show biological effects. Salt can therefore only significantly contribute the essential elements sodium, chlorine, and, if added on purpose, fluorine and iodine to human nutrition. The contribution of all other traces in salt to the average daily human requirements can be neglected. Thus, from an analytical point of view, there is no health reason to use unpurified salt. There are, however, a few drawbacks to the use of unpurified salt, as hygroscopic compounds like MgCl 2 , and even toxic heavy metals like chromium or thorium. Especially rare earth element (REE) concentrations can often be used to obtain a chemical fingerprint, which can be used to identify the origin of an unknown sample. In the case of this study, the sample number from each region was too small to collect significant data. Therefore more analytical information is needed

  8. Behavior of Rare-Earth Metals in Vacuum Melting and Directional Solidification of Nickel Superalloys

    Science.gov (United States)

    Sidorov, V. V.; Min, P. G.

    2017-12-01

    The interaction of the nickel melt containing REMs (Y, Ce, and La) with the ceramic material of a melting crucible (Al2O3, MgO • Al2O3, Y2O3) during vacuum melting and with a mold (Al2O3) during directional solidification of has been detected experimentally. The REM concentration in a metal decreases as a result of holding of an REM-containing melt in a ceramic crucible or a mold. This should be taken into account to achieve the optimal required REM content in alloys.

  9. Effects of Rare Earth Metal addition on the cavitation erosion-corrosion resistance of super duplex stainless steels

    Science.gov (United States)

    Shim, Sung-Ik; Park, Yong-Soo; Kim, Soon-Tae; Song, Chi-Bok

    2002-05-01

    Austenitic stainless steels such as AISI 316L have been used in equipment in which fluid flows at high speeds which can induce cavitation erosion on metallic surfaces due to the collapse of cavities, where the collapse is caused by the sudden change of local pressure within the liquid. Usually AISI 316L is susceptible to cavitation erosion. This research focuses on developing a better material to replace the AISI 316L used in equipment with high speed fluid flow, such as impellers. The effects of Rare Earth Metal (REM) additions on the cavitation erosion-corrosion resistance of duplex stainless steels were studied using metallographic examination, the potentiodynamic anodic polarization test, the tensile test, the X-ray diffraction test and the ultrasonic cavitation erosion test. The experimental alloys were found to have superior mechanical properties due to interstitial solid solution strengthening, by adding high nitrogen (0.4%), as well as by the refinement of phases and grains induced by fine REM oxides and oxy-sulfides. Corrosion resistance decreases in a gentle gradient as the REM content increases. However, REM containing alloys show superior corrosion resistance compared with that of other commercial alloys (SAF 2507, AISI 316L). Owing to their excellent mechanical properties and corrosion resistance, the alloys containing REM have high cavitation erosion-corrosion resistance.

  10. Synchrotron Diffraction Studies of Spontaneous Magnetostriction in Rare Earth Transition Metal Compounds

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Ning [Iowa State Univ., Ames, IA (United States)

    2004-12-19

    Thermal expansion anomalies of R2Fe14B and R2Fe17Cx (x = 0,2) (R = Y, Nd, Gd, Tb, Er) stoichiometric compounds are studied with high-energy synchrotron X-ray powder diffraction using Debye-Schemer geometry in temperature range 10K to 1000K. Large spontaneous magnetostriction up to their Curie temperatures (Tc) is observed. The a-axes show relatively larger invar effects than c-axes in the R2Fe14B compounds whereas the R2Fe17Cx show the contrary anisotropies. The iron sub-lattice is shown to dominate the spontaneous magnetostriction of the compounds. The contribution of the rare earth sublattice is roughly proportional to the spin magnetic moment of the rare earth in the R2Fe14B compounds but in R2Fe17Cx, the rare earth sub-lattice contribution appears more likely to be dominated by the local bonding. The calculation of spontaneous magnetostrain of bonds shows that the bonds associated with Fe(j2) sites in R2Fe14B and the dumbbell sites in R2Fe17Cx have larger values, which is strongly related to their largest magnetic moment and Wigner-Seitz atomic cell volume. The roles of the carbon atoms in increasing the Curie temperatures of the R2Fe17 compounds are attributed to the increased separation of Fe hexagons. The R2Fe17 and R2Fe14B phases with magnetic rare earth ions also show anisotropies of thermal expansion above c. For R2Fe17 and R2Fe14B the a a/a c > 1 whereas the anisotropy is reversed with the interstitial carbon in R2Fe17. The average bond magnetostrain is shown to be a possible predictor of the magnetic moment of Fe sites in the compounds. Both of the theoretical and

  11. Effect of metallic nanoparticle fillers on the thermal conductivity of diatomaceous earth

    Science.gov (United States)

    Diallo, Mouhamad S.; Srinivasan, Srilok; Chang, Boyce; Ghosh, Suvojit; Balasubramanian, Ganesh

    2016-10-01

    Thermal conductivity of solid nanoparticles (aluminum) in a nanoporous solid matrix (diatomaceous earth) is examined to understand the effect of conductive fillers on the thermal properties of a porous material. We find that thermal conductivity is strongly dependent on load applied to prepare the mixture compacts, while porosity is influenced by the composition of the mixture. The addition of nanoparticles contributes to limited increases in thermal conductivity of the mixture by (1) increasing contact area between the mixture constituents and (2) reduction of porosity that leads to enhanced solid-gas coupling contribution. Thermal conductivity increases exponentially with external gas pressures due to the coupling effect between the solid particles and the entrapped air.

  12. Exploration of earth-abundant transition metals (Fe, Co, and Ni) as catalysts in unreactive chemical bond activations.

    Science.gov (United States)

    Su, Bo; Cao, Zhi-Chao; Shi, Zhang-Jie

    2015-03-17

    Activation of inert chemical bonds, such as C-H, C-O, C-C, and so on, is a very important area, to which has been drawn much attention by chemists for a long time and which is viewed as one of the most ideal ways to produce valuable chemicals. Under modern chemical bond activation logic, many conventionally viewed "inert" chemical bonds that were intact under traditional conditions can be reconsidered as novel functionalities, which not only avoids the tedious synthetic procedures for prefunctionalizations and the emission of undesirable wastes but also inspires chemists to create novel synthetic strategies in completely different manners. Although activation of "inert" chemical bonds using stoichiometric amounts of transition metals has been reported in the past, much more attractive and challenging catalytic transformations began to blossom decades ago. Compared with the broad application of late and noble transition metals in this field, the earth-abundant first-row transition-metals, such as Fe, Co, and Ni, have become much more attractive, due to their obvious advantages, including high abundance on earth, low price, low or no toxicity, and unique catalytic characteristics. In this Account, we summarize our recent efforts toward Fe, Co, and Ni catalyzed "inert" chemical bond activation. Our research first unveiled the unique catalytic ability of iron catalysts in C-O bond activation of both carboxylates and benzyl alcohols in the presence of Grignard reagents. The benzylic C-H functionalization was also developed via Fe catalysis with different nucleophiles, including both electron-rich arenes and 1-aryl-vinyl acetates. Cobalt catalysts also showed their uniqueness in both aromatic C-H activation and C-O activation in the presence of Grignard reagents. We reported the first cobalt-catalyzed sp(2) C-H activation/arylation and alkylation of benzo[h]quinoline and phenylpyridine, in which a new catalytic pathway via an oxidative addition process was demonstrated

  13. Electrocatalytic Hydrogenation of Oxygenates using Earth-Abundant Transition-Metal Nanoparticles under Mild Conditions.

    Science.gov (United States)

    Carroll, Kyler J; Burger, Thomas; Langenegger, Lukas; Chavez, Steven; Hunt, Sean T; Román-Leshkov, Yuriy; Brushett, Fikile R

    2016-08-09

    Electrocatalytic hydrogenation (ECH) is a sustainable pathway for the synthesis of value-added organic compounds, provided affordable catalysts with high activity, selectivity and durability are developed. Here, we synthesize Cu/C, Ni/C, and CuNi/C nanoparticles and compare their performance to Pt/C, Ru/C, PtRu/C for the ECH of hydroxyacetone, a bio-derived feedstock surrogate containing a carbonyl and a hydroxyl functional group. The non-precious metal electrocatalysts show promising conversion-time behavior, product selectivities, and Faradaic efficiencies. Ni/C forms propylene glycol with a selectivity of 89 % (at 80 % conversion), while Cu/C catalyzes ECH (52 % selectivity) and hydrodeoxygenation (HDO, 48 % selectivity, accounting for evaporation). CuNi/C shows increased turnover frequencies but reduced ECH selectivity (80 % at 80 % conversion) as compared to the Ni/C catalyst. Importantly, stability studies show that the non-precious metal catalysts do not leach at operating conditions. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Study of hydrogenation for pulverization of rare earth alloys with Nb for metal hydride electrodes

    International Nuclear Information System (INIS)

    Ferreira, Eliner Affonso

    2013-01-01

    In this work were studied La ,7 Mg 0,3 Al 0,3 Mn 0,4 Co (0.5-x) NbxNi 3.8 (x= 0 - 0.5) and La 0,7 Mg 0,3 Al 0,3 Mn 0.4 Nb (05+x) Co 0,5 Ni (3.8-x) . (x=0.3; 0.5;1.3) alloys for negative electrodes of the Nickel-Metal Hydride batteries. The hydrogenation of the alloys was performed varying pressing of H 2 (2 and 9 bar). The discharge capacity of the nickel-metal hydride batteries were analyzed in the Arbin BT-4 electrical test equipment. The as-cast alloys were analyzed by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and X-Ray diffraction. The increasing Niobium addition in the alloys decreased cycle life and the maximum discharge capacity of the batteries. The maximum discharge capacity was obtained with the La .7 Mg 0.3 Al 0.3 Mn 0,4 Co 0.5 Ni 3.8 (45.36 mAh) and the battery which presented the best performance was La .7 Mg 0.3 Al 0.3 Mn 0.4 Co 0.5 Nb 0.1 Ni 3.8 (44.94 mAh). (author)

  15. Electrochemical separation of actinides and fission products in molten salt electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Gay, R.L.; Grantham, L.F.; Fusselman, S.P. [Rockwell International/Rocketdyne Division, Canoga Park, CA (United States)] [and others

    1995-10-01

    Molten salt electrochemical separation may be applied to accelerator-based conversion (ABC) and transmutation systems by dissolving the fluoride transport salt in LiCl-KCl eutectic solvent. The resulting fluoride-chloride mixture will contain small concentrations of fission product rare earths (La, Nd, Gd, Pr, Ce, Eu, Sm, and Y) and actinides (U, Np, Pu, Am, and Cm). The Gibbs free energies of formation of the metal chlorides are grouped advantageously such that the actinides can be deposited on a solid cathode with the majority of the rare earths remaining in the electrolyte. Thus, the actinides are recycled for further transmutation. Rockwell and its partners have measured the thermodynamic properties of the metal chlorides of interest (rare earths and actinides) and demonstrated separation of actinides from rare earths in laboratory studies. A model is being developed to predict the performance of a commercial electrochemical cell for separations starting with PUREX compositions. This model predicts excellent separation of plutonium and other actinides from the rare earths in metal-salt systems.

  16. Theoretical study on the role of surface basicity and Lewis acidity on the etherification of glycerol over alkaline earth metal oxides

    NARCIS (Netherlands)

    Calatayud, M.; Ruppert, A.M.|info:eu-repo/dai/nl/314003398; Weckhuysen, B.M.|info:eu-repo/dai/nl/285484397

    2009-01-01

    Alkaline earth metal oxides (MO) are catalytically active in the etherification of glycerol. Density Functional Theory (DFT) calculations have been used to examine the reactivity of glycerol with MO surfaces with M=Mg, Ca, Sr or Ba. More specifically, the optimum glycerol adsorption mode and the

  17. Submarine Salt Karst Terrains

    Directory of Open Access Journals (Sweden)

    Nico Augustin

    2016-06-01

    earth scientists seeking hydrocarbons associated with salt bodies.

  18. Colorimetric and bare-eye detection of alkaline earth metal ions based on the aggregation of silver nanoparticles functionalized with thioglycolic acid

    International Nuclear Information System (INIS)

    Wu, Xiaoyan; Tang, Wanxin; Hou, Cong; Zhang, Chao; Zhu, Ningning

    2014-01-01

    We describe a simple and rapid method for colorimetric and bare-eye detection of the alkaline earth metal ions Mg(II), Ca(II), Sr(II) and Ba(II) based on the use of silver nanoparticles (AgNPs) functionalized with thioglycolic acid (TGA). The TGA ligand was self-assembled onto the AgNPs to form a probe that undergoes a color change from yellow to orange or red on exposure to the alkaline earth ions. It is presumed that the color change is a result of the aggregation of the AgNPs caused by the interaction of the bivalent ions with the carboxy groups on the AgNPs. The color change can be used for bare-eye and colorimetric determination of the alkaline earth metal ions, for example to rapidly determine water hardness. (author)

  19. Organic salt NEDC (N-naphthylethylenediamine dihydrochloride) assisted laser desorption ionization mass spectrometry for identification of metal ions in real samples.

    Science.gov (United States)

    Hou, Jian; Chen, Suming; Zhang, Ning; Liu, Huihui; Wang, Jianing; He, Qing; Wang, Jiyun; Xiong, Shaoxiang; Nie, Zongxiu

    2014-07-07

    The significance of metals in life and their epidemiological effects necessitate the development of a direct, efficient, and rapid method of analysis. The matrix assisted laser desorption/ionization technique is on the horns of a dilemma of metal analysis as the conventional matrixes have high background in the low mass range. An organic salt, NEDC (N-naphthylethylenediamine dihydrochloride), is applied as a matrix for identification of metal ions in the negative ion mode in the present work. Sixteen metal ions, Ba(2+), Ca(2+), Cd(2+), Ce(3+), Co(2+), Cu(2+), Fe(3+), Hg(2+), K(+), Mg(2+), Mn(2+), Na(+), Ni(2+), Pb(2+), Sn(2+) and Zn(2+), in the form of their chloride-adducted clusters were systematically tested. Mass spectra can provide unambiguous identification through accurate mass-to-charge ratios and characteristic isotope patterns. Compared to ruthenium ICP standard solution, tris(2,2'-bipyridyl)dichlororuthenium(ii) (C30H24N6Cl2Ru) can form organometallic chloride adducts to discriminate from the inorganic ruthenium by this method. After evaluating the sensitivity for Ca, Cu, Mg, Mn, Pb and Zn and plotting their quantitation curves of signal intensity versus concentration, we determined magnesium concentration in lake water quantitatively to be 5.42 mg L(-1) using the standard addition method. There is no significant difference from the result obtained with ICP-OES, 5.8 mg L(-1). Human urine and blood were also detected to ascertain the multi-metal analysis ability of this strategy in complex samples. At last, we explored its applicability to tissue slice and visualized sodium and potassium distribution by mass spectrometry imaging in the normal Kunming mouse brain.

  20. Evaluation of soil metal bioavailability estimates using two plant species (L. perenne and T. aestivum) grown in a range of agricultural soils treated with biosolids and metal salts

    International Nuclear Information System (INIS)

    Black, Amanda; McLaren, Ronald G.; Reichman, Suzanne M.; Speir, Thomas W.; Condron, Leo M.

    2011-01-01

    Few studies have quantified the accuracy of soil metal bioavailability assays using large datasets. A meta-analysis from experiments spanning 6 months to 13 years on 12 soil types, compared bioavailability estimate efficiencies for wheat and ryegrass. Treatments included biosolids ± metals, comparing total metal, Ca(NO 3 ) 2 , EDTA, soil solution, DGT and free ion activity. The best correlations between soil metal bioavailability and shoot concentrations were for Ni using Ca(NO 3 ) 2 (r 2 = 0.72) which also provided the best estimate of Zn bioavailability (r 2 = 0.64). DGT provided the best estimate of Cd bioavailability, accounting for 49% of shoot Cd concentrations. There was no reliable descriptor of Cu bioavailability, with less than 35% of shoot Cu concentrations defined. Thus interpretation of data obtained from many soil metal bioavailability assays is unreliable and probably flawed, and there is little justification to look beyond Ca(NO 3 ) 2 for Ni and Zn, and DGT for Cd. - Highlights: → A meta-analysis evaluated the efficacy of soil metal bioavailability assays. → DGT could explain 49% of shoot Cd concentration. → There is little justification to look beyond Ca(NO 3 ) 2 for Ni and Zn. - A meta-analysis of soil metal bioavailability estimates for 12 soil types concluded that there is little justification to look beyond Ca(NO 3 ) 2 for Ni and Zn, and DGT for Cd.

  1. Evaluation of soil metal bioavailability estimates using two plant species (L. perenne and T. aestivum) grown in a range of agricultural soils treated with biosolids and metal salts

    Energy Technology Data Exchange (ETDEWEB)

    Black, Amanda, E-mail: amanda.black@lincoln.ac.nz [Department of Soil and Physical Sciences, Faculty of Agriculture and Life Sciences, Lincoln University, PO Box 84, Lincoln 7647, Christchurch (New Zealand); McLaren, Ronald G. [Department of Soil and Physical Sciences, Faculty of Agriculture and Life Sciences, Lincoln University, PO Box 84, Lincoln 7647, Christchurch (New Zealand); Reichman, Suzanne M. [School of Civil, Environmental and Chemical Engineering, RMIT University, GPO Box 2476, Melbourne 3001 (Australia); Speir, Thomas W. [Institute of Environmental Science and Research Ltd (ESR), PO Box 50348, Porirua 5240 (New Zealand); Condron, Leo M. [Department of Soil and Physical Sciences, Faculty of Agriculture and Life Sciences, Lincoln University, PO Box 84, Lincoln 7647, Christchurch (New Zealand)

    2011-06-15

    Few studies have quantified the accuracy of soil metal bioavailability assays using large datasets. A meta-analysis from experiments spanning 6 months to 13 years on 12 soil types, compared bioavailability estimate efficiencies for wheat and ryegrass. Treatments included biosolids {+-} metals, comparing total metal, Ca(NO{sub 3}){sub 2}, EDTA, soil solution, DGT and free ion activity. The best correlations between soil metal bioavailability and shoot concentrations were for Ni using Ca(NO{sub 3}){sub 2} (r{sup 2} = 0.72) which also provided the best estimate of Zn bioavailability (r{sup 2} = 0.64). DGT provided the best estimate of Cd bioavailability, accounting for 49% of shoot Cd concentrations. There was no reliable descriptor of Cu bioavailability, with less than 35% of shoot Cu concentrations defined. Thus interpretation of data obtained from many soil metal bioavailability assays is unreliable and probably flawed, and there is little justification to look beyond Ca(NO{sub 3}){sub 2} for Ni and Zn, and DGT for Cd. - Highlights: > A meta-analysis evaluated the efficacy of soil metal bioavailability assays. > DGT could explain 49% of shoot Cd concentration. > There is little justification to look beyond Ca(NO{sub 3}){sub 2} for Ni and Zn. - A meta-analysis of soil metal bioavailability estimates for 12 soil types concluded that there is little justification to look beyond Ca(NO{sub 3}){sub 2} for Ni and Zn, and DGT for Cd.

  2. Hydrogenation of the rare earth alloys for production negative electrodes of nickel-metal hydride batteries

    International Nuclear Information System (INIS)

    Casini, Julio Cesar Serafim

    2011-01-01

    In this work were studied of La 0.7-x Mg x Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 (X = 0 and 0.7) alloys for negative electrodes of the nickel-metal hydride batteries. The hydrogenation of the alloys was performed varying pressing of H 2 (2 and 10 bar) and temperature (room and 500 ℃). The discharge capacity of the nic kel-metal hydride batteries were analyzed in ARBIN BT- 4 electrical test equipment. The as-cast alloys were analyzed by scanning electron microscopy (SEM), energy disperse spectroscopy (EDX) and X-Ray diffraction. The increasing Mg addition in the alloy increases maximum discharge capacity but decrease cycle life of the batteries. The maximum discharge capacity was obtained with the Mg 0.7 Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 alloy (60 mAh) and the battery which presented the best performance was La 0.4 Mg 0.3 Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 alloy (53 mAh and 150 cycles). The H 2 capability of absorption was diminished for increased Mg addition and no such effect occurs for Mg 0.7 Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 alloy. (author)

  3. Cure and mechanical properties of carboxylated nitrile rubber (XNBR) vulcanized by alkaline earth metal compounds

    Science.gov (United States)

    Tulyapitak, Tulyapong

    Compounds of carboxylated nitrile rubber (XNBR) with alkaline metal oxides and hydroxide were prepared, and their cure and mechanical properties were investigated. Magnesium oxide (MgO) with different specific surface areas (45, 65, and 140 m2/g) was used. Increased specific surface area and concentration of MgO resulted in higher cure rate. Optimum stiffness, tensile strength, and ultimate strain required an equimolar amount of acidity and MgO. The effect of specific surface area on tensile properties was not significant. Crosslink density of XNBR-MgO vulcanizates increased with increased amounts of MgO. ATR-IR spectroscopy showed that neutralization occurs in two steps: (1) During mixing and storage, MgO reacts with carboxyl groups (RCOOH) to give RCOOMgOH. (2) Upon curing, these react bimolecularly to form RCOOMgOOCR and Mg(OH)2. Dynamic mechanical thermal analysis revealed an ionic transition at higher temperature, in addition to the glass transition. The ionic transition shifts to higher temperature with increasing MgO concentration. Like MgO-XNBR systems, cure rates of XNBR-calcium hydroxide (Ca(OH)2) and XNBR-barium oxide (BaO) compounds increased with increased content of curing agents. Curing by these two agents resulted in ionic crosslinks. To ensure optimum tensile properties, equimolar amounts of carboxyl groups and curing agents were required. Dynamic mechanical analysis revealed the ionic transition in these two systems. It shifted to higher temperature with increased amounts of curing agents. In contrast to MgO, Ca(OH)2, and BaO, calcium oxide (CaO) gave results similar to those for thermally cured samples. No ionic transition was observed in XNBR-CaO systems. Tensile strength of XNBR depended on the strength of ionic crosslinks, which was dependent on the size of the alkaline metal ions.

  4. A geological reconnaissance of electrical and electronic waste as a source for rare earth metals.

    Science.gov (United States)

    Mueller, Sandra R; Wäger, Patrick A; Widmer, Rolf; Williams, Ian D

    2015-11-01

    The mining of material resources requires knowledge about geogenic and anthropogenic deposits, in particular on the location of the deposits with the comparatively highest concentration of raw materials. In this study, we develop a framework that allows the establishment of analogies between geological and anthropogenic processes. These analogies were applied to three selected products containing rare earth elements (REE) in order to identify the most concentrated deposits in the anthropogenic cycle. The three identified anthropogenic deposits were characterised according to criteria such as "host rock", "REE mineralisation" and "age of mineralisation", i.e. regarding their "geological" setting. The results of this characterisation demonstrated that anthropogenic deposits have both a higher concentration of REE and a longer mine life than the evaluated geogenic deposit (Mount Weld, Australia). The results were further evaluated by comparison with the geological knowledge category of the United Nations Framework Classification for Fossil Energy and Mineral Reserves and Resources 2009 (UNFC-2009) to determine the confidence level in the deposit quantities. The application of our approach to the three selected cases shows a potential for recovery of REE in anthropogenic deposits; however, further exploration of both potential and limitations is required. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

  5. Metal oxide nanoparticles embedded in rare-earth matrix for low temperature thermal imaging applications

    Science.gov (United States)

    Rauwel, E.; Galeckas, A.; Rauwel, P.; Hansen, P.-A.; Wragg, D.; Nilsen, O.; Fjellvåg, H.

    2016-05-01

    We report on the synthesis and characterization of nanocomposites comprising of oxide nanoparticles (NPs) (ZnO, CaHfO3 and SrHfO3) embedded in rare-earth oxide (Eu2O3, Nd2O3) matrices by using atomic layer deposition. The different oxide surroundings allowed highlighting the role of interface defects in the recombination processes of charge carriers in the NPs. We provide a comparative analysis of optical absorption and emission properties of the constituents: thin films, free-standing and embedded NPs, and discuss the intrinsic and extrinsic nature of the luminescent sites in different nanocomposites. The photoluminescence properties of ZnO nanocomposites are clearly distinguishable from those of free-standing NPs in terms of overall quantum efficiency as well as intensity ratios of the characteristic blue and green emission bands associated with radiative transitions involving excitons and intrinsic defects, respectively. In contrast to PL enhancement due to surface-passivating effect of the surrounding media in the case of ZnO nanocomposites, the embedment of hafnia perovskites into oxide matrices generally leads to suppressed luminescence in the visible range, thus confirming its extrinsic, surface-defect related nature.

  6. Effect of metallic nanoparticle fillers on the thermal conductivity of diatomaceous earth

    Energy Technology Data Exchange (ETDEWEB)

    Diallo, Mouhamad S. [Department of Liberal Arts, Des Moines Area Community College, Des Moines, IA 50314 (United States); Department of Mechanical Engineering, Iowa State University, Ames, IA 50011 (United States); Srinivasan, Srilok [Department of Mechanical Engineering, Iowa State University, Ames, IA 50011 (United States); Chang, Boyce [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Ghosh, Suvojit [Department of Engineering Physics, McMaster University, Hamilton, ON L8S4L8 (Canada); Balasubramanian, Ganesh, E-mail: bganesh@iastate.edu [Department of Mechanical Engineering, Iowa State University, Ames, IA 50011 (United States)

    2016-10-23

    Thermal conductivity of solid nanoparticles (aluminum) in a nanoporous solid matrix (diatomaceous earth) is examined to understand the effect of conductive fillers on the thermal properties of a porous material. We find that thermal conductivity is strongly dependent on load applied to prepare the mixture compacts, while porosity is influenced by the composition of the mixture. The addition of nanoparticles contributes to limited increases in thermal conductivity of the mixture by (1) increasing contact area between the mixture constituents and (2) reduction of porosity that leads to enhanced solid–gas coupling contribution. Thermal conductivity increases exponentially with external gas pressures due to the coupling effect between the solid particles and the entrapped air. - Highlights: • Thermal conductivity k of DE/AlNP mixture is more dependent on compaction than on Al concentration. • Nanoparticles affect k of DE by increase in solid contact area rather than by its effect on porosity. • When air content in mixture rises, k increases with gas pressures due to solid–gas coupling effect.

  7. Effect of metallic nanoparticle fillers on the thermal conductivity of diatomaceous earth

    International Nuclear Information System (INIS)

    Diallo, Mouhamad S.; Srinivasan, Srilok; Chang, Boyce; Ghosh, Suvojit; Balasubramanian, Ganesh

    2016-01-01

    Thermal conductivity of solid nanoparticles (aluminum) in a nanoporous solid matrix (diatomaceous earth) is examined to understand the effect of conductive fillers on the thermal properties of a porous material. We find that thermal conductivity is strongly dependent on load applied to prepare the mixture compacts, while porosity is influenced by the composition of the mixture. The addition of nanoparticles contributes to limited increases in thermal conductivity of the mixture by (1) increasing contact area between the mixture constituents and (2) reduction of porosity that leads to enhanced solid–gas coupling contribution. Thermal conductivity increases exponentially with external gas pressures due to the coupling effect between the solid particles and the entrapped air. - Highlights: • Thermal conductivity k of DE/AlNP mixture is more dependent on compaction than on Al concentration. • Nanoparticles affect k of DE by increase in solid contact area rather than by its effect on porosity. • When air content in mixture rises, k increases with gas pressures due to solid–gas coupling effect.

  8. A volatile topic: Parsing out the details of Earth's formation through experimental metal-silicate partitioning of volatile and moderately volatile elements

    Science.gov (United States)

    Mahan, B. M.; Siebert, J.; Blanchard, I.; Badro, J.; Sossi, P.; Moynier, F.

    2017-12-01

    Volatile and moderately volatile elements display different volatilities and siderophilities, as well as varying sensitivity to thermodynamic controls (X, P, T, fO2) during metal-silicate differentiation. The experimental determination of the metal-silicate partitioning of these elements permits us to evaluate processes controlling the distribution of these elements in Earth. In this work, we have combined metal-silicate partitioning data and results for S, Sn, Zn and Cu, and input these characterizations into Earth formation models. Model parameters such as source material, timing of volatile delivery, fO2 path, and degree of impactor equilibration were varied to encompass an array of possible formation scenarios. These models were then assessed to discern plausible sets of conditions that can produce current observed element-to-element ratios (e.g. S/Zn) in the Earth's present-day mantle, while also satisfying current estimates on the S content of the core, at no more than 2 wt%. The results of our models indicate two modes of accretion that can maintain chondritic element-to-element ratios for the bulk Earth and can arrive at present-day mantle abundances of these elements. The first mode requires the late addition of Earth's entire inventory of these elements (assuming a CI-chondritic composition) and late-stage accretion that is marked by partial equilibration of large impactors. The second, possibly more intuitive mode, requires that Earth accreted - at least initially - from volatile poor material preferentially depleted in S relative to Sn, Zn, and Cu. From a chemical standpoint, this source material is most similar to type I chondrule rich (and S poor) materials (Hewins and Herzberg, 1996; Mahan et al., 2017; Amsellem et al., 2017), such as the metal-bearing carbonaceous chondrites.

  9. How can we take advantage of halophyte properties to cope with heavy metal toxicity in salt-affected areas?

    Czech Academy of Sciences Publication Activity Database

    Lutts, S.; Lefevre, Isabelle

    2015-01-01

    Roč. 115, č. 3 (2015), s. 509-528 ISSN 0305-7364 Institutional support: RVO:60077344 Keywords : Antioxidants * glycinebetaine * metal distribution * osmoprotectants Subject RIV: BO - Biophysics Impact factor: 3.982, year: 2015

  10. Equilibrium mononuclear-trinuclear complex in acetonitrile solutions of copper (2) N,N'-ethylene-bis-salicylideneiminate and alkaline earth metal perchlorates

    International Nuclear Information System (INIS)

    Zheltvaj, I.I.; Siritsov, A.I.; Egorova, A.L.; Kamalov, G.L.

    1985-01-01

    Trinuclear adducts of copper (2) NN'-ethylene-bis salicylidenimi=n ate (CuES) with alkaline earth metal perchlorates are dissolved in acetonitrile with the preservation of polynuclear structure, which is confirmed by the data of vibrational and electron spectroscopy. Reversible dissociation of polynuclear adduct is detected, its scale depending on alkaline earth metal nature and increasing in the series Mg 2+ reversible M(CuES) 2 are found, the logarithms of which in the above-mentioned series of metals equal: 11.7+-0.1; 10.5+-0.1; 9.3+-0.1; 8.1+-0.1 and correlate linearly with the absorption band frequencies of the corresponding complexes. Possible reasons for the correlation are discussed

  11. R and D activities on the management of waste chloride salts in KAERI

    International Nuclear Information System (INIS)

    In-Tae, Kim; Hwan-Seo, Park; Jeong-Gook, Kim; Hee-Chul, Yang; Yong-Joon, Cho; Eung-Ho Kim

    2007-01-01

    Full text of publication follows. Electrochemical treatment of spent oxide fuels has been intensively studied in KAERI to reduce the volume, heat load and radiotoxicity of high-level wastes. It consists of an electrolytic reduction process to convert the oxide fuel into a metallic form and an electro-refining process to separate TRU elements from the electro-reduced metal ingot. Two types of waste salts are expected to generate from the electrochemical pyro-processes, that is, LiCl salt from the reduction process and LiCl+KCl eutectic salt form the refining process. The R and D strategy of the waste salt management in KAERI can be categorized into two parts: 1) enhancement of safety by the stabilisation/solidification of waste salt that is to be finally disposed of and 2) reduction of the waste generation by the regeneration/recycle of the spent salt after removal of radionuclides in it. A sol-gel technique and a zeolite occlusion technique are under development to stabilize the waste salt. The LiCl salt is stabilised by a low-temperature sol-gel process and then the gel product is solidified into a ceramic-like waste form with an addition of glass frit. Another method uses Zeolite-4A to occlude the LiCl salt into its cage and adsorption site to immobilize the radionuclides. The product, salt-occluded zeolite, is fabricated into another type of a ceramic waste form. For the regeneration and recycle of the spent salt, the radionuclides in the salt are removed by a zeolite process for the LiCl salt and by an oxidation/distillation process for the eutectic salt. The target nuclides to be removed in each process are Cs/Sr and rare earth (RE) elements, respectively. In the oxidation/ distillation process, the rare earth chloride nuclides are oxidised by an oxygen sparging method, and the products are precipitated in the form of oxide or oxychloride REs. After separation of the RE elements from the precipitates by distillation, the refined spent salt with a low content

  12. Studies on the biofilm produced by Pseudomonas aeruginosa grown in different metal fatty acid salt media and its application in biodegradation of fatty acids and bioremediation of heavy metal ions.

    Science.gov (United States)

    Abinaya Sindu, P; Gautam, Pennathur

    2017-01-01

    Metal fatty acid salts (MFAS) in untreated industrial effluents cause environmental pollution. The use of biocompatible agents for remediation may help in reducing the harm caused to the ambient aquatic organism. Pseudomonas aeruginosa is a ubiquitous organism that thrives under harsh conditions and is resistant to toxic metal ions. The present study shows a proof-of-concept of using this organism in the biodegradation of MFAS. MFAS were prepared and we studied their effect on the growth of the planktonic form and the formation of biofilm by P. aeruginosa. We observed biofilm formation in the presence of all the MFAS when used as the sole carbon source, albeit the quantity of biofilm formed in the presence of cadmium and copper was less. There was no effect on the planktonic form of the organism but the formation of biofilm increased in the presence of magnesium palmitate. This study shows that metal ions play a pivotal role in the formation of biofilm. HPLC (high-performance liquid chromatography) analysis of the biofilm polysaccharide showed that hexose sugar was a major component when compared with pentose sugar. The structure of biofilm polysaccharide and the coordination of the metal ion with the biofilm polysaccharide were confirmed by FTIR (Fourier transform infrared spectroscopy) and Raman spectroscopy.

  13. ANAEROBIC RESISTANCE TO HIGH LEVELS OF CADMIUM AND OTHER TOXIC METALS IN A FACULTATIVE ANAEROBE ISOLATED FROM PRISTINE SALT MARSH SEDIMENTS

    Energy Technology Data Exchange (ETDEWEB)

    SHARMA,P.K.; VAIRAVAMURTHY,A.; KIELECZAWA,J.

    1999-06-20

    The authors have isolated many Cd (II) resistant bacterial strains from relatively pristine sediments collected from salt marshes in Shelter Island, New York. Detailed studies are being performed on one isolate, strain Cd-1. Strain Cd-1 is metabolically diverse, halotolerant, Gram-negative, facultative anaerobe. It can resist high amounts of Cd (II), Cr (VI), As (V), Se (IV), Co (II), Pb (II), or Zn (II) under defined anaerobic conditions. With pyruvate as the energy source, Cd-1 can grow well at examined Cd (II) concentrations ranging up to 15 mM. It can resist Cd (II) with or without marine level NaCl concentration, under acidic or neutral conditions. It can resist Cd (II) under aerobic conditions as well. These features are novel for a heavy metal resistant bacterium.

  14. Enhanced NH3 gas sensing performance based on electrospun alkaline-earth metals composited SnO2 nanofibers

    International Nuclear Information System (INIS)

    Xu, Shuang; Kan, Kan; Yang, Ying; Jiang, Chao; Gao, Jun; Jing, Liqiang; Shen, Peikang; Li, Li

    2015-01-01

    Highlights: • The small-sized SnO 2 (5–7 nm) were obtained by adding the alkaline-earth. • Sr-composited SnO 2 nanofibers showed uniform nanotubes structure (Sr/SnO 2 ). • Sr/SnO 2 showed an excellent sensing performance to NH 3 at room temperature. - Abstract: One-dimensional alkaline-earth metals composited SnO 2 (Ae/SnO 2 ) nanofibres were fabricated via electrospinning technique, followed by thermal treatment at 600 °C for 5 h. Transmission electron microscopy (TEM) studies showed that the nanoparticles size of Ae/SnO 2 was 5–7 nm, which was smaller than the pristine SnO 2 nanorods attached by 20 nm nanoparticles. Moreover, Sr/SnO 2 nanocomposites showed uniform nanotubes structure with the wall thickness of about 30 nm, in which all the nanoparticles were connected to their neighbors by necks. The Sr/SnO 2 nanotubes exhibited an excellent sensing response toward NH 3 gas at room temperature, lower detection limit (10 ppm), faster response time (6 s towards 2000 ppm∼16 s towards 10 ppm) and better reversibility compared to the pristine SnO 2 nanorods. The enhanced sensor performances were attributed to the higher conductivity of the Sr/SnO 2 . Mott–Schottky plots (M–S) and electrochemical impedance spectroscopy (EIS) measurements indicated that the carrier density of Sr/SnO 2 nanotubes was 3 fold of that pristine SnO 2

  15. Dipole polarizability of alkali-metal (Na, K, Rb)–alkaline-earth-metal (Ca, Sr) polar molecules: Prospects for alignment

    Energy Technology Data Exchange (ETDEWEB)

    Gopakumar, Geetha, E-mail: geetha@tmu.ac.jp; Abe, Minori; Hada, Masahiko [Department of Chemistry, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji, Tokyo 192-0397 (Japan); JST, CREST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Kajita, Masatoshi [National Institute of Information and Communications Technology, Koganei, Tokyo 184-8795 (Japan)

    2014-06-14

    Electronic open-shell ground-state properties of selected alkali-metal–alkaline-earth-metal polar molecules are investigated. We determine potential energy curves of the {sup 2}Σ{sup +} ground state at the coupled-cluster singles and doubles with partial triples (CCSD(T)) level of electron correlation. Calculated spectroscopic constants for the isotopes ({sup 23}Na, {sup 39}K, {sup 85}Rb)–({sup 40}Ca, {sup 88}Sr) are compared with available theoretical and experimental results. The variation of the permanent dipole moment (PDM), average dipole polarizability, and polarizability anisotropy with internuclear distance is determined using finite-field perturbation theory at the CCSD(T) level. Owing to moderate PDM (KCa: 1.67 D, RbCa: 1.75 D, KSr: 1.27 D, RbSr: 1.41 D) and large polarizability anisotropy (KCa: 566 a.u., RbCa: 604 a.u., KSr: 574 a.u., RbSr: 615 a.u.), KCa, RbCa, KSr, and RbSr are potential candidates for alignment and orientation in combined intense laser and external static electric fields.

  16. Heavy metals, salts and organic residues in old solid urban waste landfills and surface waters in their discharge areas: determinants for restoring their impact.

    Science.gov (United States)

    Pastor, J; Hernández, A J

    2012-03-01

    This study was designed to determine the state of polluted soils in the main landfills of the Community of Madrid (central Spain), as part of a continuous assessment of the impacts of urban solid waste (USW) landfills that were capped with a layer of soil 20 years ago. Our analysis of this problem has been highly conditioned by the constant re-use of many of the USW landfills, since they have never been the target of any specific restoration plan. Our periodical analysis of cover soils and soils from discharge areas of the landfills indicates soil pollution has worsened over the years. Here, we examined heavy metal, salts, and organic compounds in soil and surface water samples taken from 15 landfills in the Madrid region. Impacts of the landfill soil covers on nematode and plant diversity were also evaluated. These analyses continue to reveal the presence of heavy metals (Zn, Cu, Cr, Ni, Pb, Cd) in soils, and salts (sulphates, chlorides and nitrates) in soils and surface waters. In addition, non-agricultural organic compounds, mainly aromatic and aliphatic hydrocarbons, often appeared in very high concentrations, and high levels of insecticides such as gamma-HCH (lindane) were also detected in soils. Around 50% of the water samples collected showed chemical demand of oxygen (CDO) values in excess of 150 mg/l. Traces of phenolic compounds were detected in some landfills, some of which exhibited high levels of 2-chlorophenol and pentachlorophenol. All these factors are conditioning both the revegetation of the landfill systems and the remediation of their slopes and terrestrial ecosystems arising in their discharge areas. This work updates the current situation and discusses risks for the health of the ecosystems, humans, domestic animals and wildlife living close to these landfills. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Fuel and Core Design Options to Overcome the Heavy Metal Loading Limit and Improve Performance and Safety of Liquid Salt Cooled Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, Bojan [Georgia Inst. of Technology, Atlanta, GA (United States); Maldonado, Ivan [Univ. of Tennessee, Knoxville, TN (United States)

    2016-04-14

    The research performed in this project addressed the issue of low heavy metal loading and the resulting reduced cycle length with increased refueling frequency, inherent to all FHR designs with solid, non-movable fuel based on TRISO particles. Studies performed here focused on AHTR type of reactor design with plate (“plank”) fuel. Proposal to FY12 NEUP entitled “Fuel and Core Design Options to Overcome the Heavy Metal Loading Limit and Improve Performance and Safety of Liquid Salt Cooled Reactors” was selected for award, and the 3-year project started in August 2012. A 4-month NCE was granted and the project completed on December 31, 2015. The project was performed by Georgia Tech (Prof. Bojan Petrovic, PI) and University of Tennessee (Prof. Ivan Maldonado, Co-PI), with a total funding of $758,000 over 3 years. In addition to two Co-PIs, the project directly engaged 6 graduate students (at doctoral or MS level) and 2 postdoctoral researchers. Additionally, through senior design projects and graduate advanced design projects, another 23 undergraduate and 12 graduate students were exposed to and trained in the salt reactor technology. We see this as one of the important indicators of the project’s success and effectiveness. In the process, 1 journal article was published (with 3 journal articles in preparation), together with 8 peer-reviewed full conference papers, 8 peer-reviewed extended abstracts, as well as 1 doctoral dissertation and 2 master theses. The work included both development of models and methodologies needed to adequately analyze this type of reactor, fuel, and its fuel cycle, as well as extensive analyses and optimization of the fuel and core design.

  18. Preliminary investigations on picoplankton-related precipitation of alkaline-earth metal carbonates in meso-oligotrophic lake Geneva (Switzerland

    Directory of Open Access Journals (Sweden)

    Jean-Michel Jaquet

    2013-10-01

    Full Text Available In the course of a routine water-quality survey in meso-oligotrophic lake Geneva (Switzerland, suspended matter was collected by filtration on 0.2 μm membranes in July and August 2012 at the depth of maximal chlorophyll a (Chl a concentration (2 mg m–3. Examination by scanning electron microscopy revealed the presence of numerous dark and gelatinous patches occluding the pores of the membranes, containing high numbers of picoplanktonic cells and, in places, clusters of high-reflectance smooth microspheres (1-2 μm in diameter. Their chemical composition, determined by semi-quantitative, energy-dispersive X ray spectroscopy (EDS showed magnesium (Mg, calcium (Ca, strontium (Sr and barium (Ba (alkaline earth metals to be the dominant cations. Among the anions, phosphorus (P and carbon (C were present, but only the latter is considered here (as carbonate. The microspheres were subdivided into four types represented in a Ca-Sr-Ba ternary space. All types are confined within a domain bound by Ca>45, Sr<10 and Ba<50 (in mole %. Type I, the most frequent, displays a broad variability in Ba/Ca, even within a given cluster. Types II and III are devoid of Ba, but may incorporate P. Type IV contains only Ca. The Type I composition resembles that of benstonite, a Group IIA carbonate that was recently found as intracellular granules in a cyanobacterium from alkaline lake Alchichica (Mexico.Lake Geneva microspheres are solid, featureless and embedded in a mucilage-looking substance in the vicinity of, but seemingly not inside, picoplanktonic cells morphologically similar to Chlorella and Synechococcus. In summer 2012, the macroscopic physico-chemical conditions in lake Geneva epilimnion were such as to allow precipitation of Ca but not of Sr and Ba carbonates. Favourable conditions did exist, though, in the micro-environment provided by the combination of active picoplankton and a mucilaginous envelope. Further studies are ongoing to investigate the

  19. Phase equilibria and thermodynamic properties of oxide systems on the basis of rare earth, alkaline earth and 3d-transition (Mn, Fe, Co metals. A short overview of

    Directory of Open Access Journals (Sweden)

    V. A. Cherepanov

    2015-12-01

    Full Text Available Review is dedicated studies of phase equilibria in the systems based on rare earth elements and 3d transition metals. It’s highlighted several structural families of these compounds and is shown that many were found interesting properties for practical application, such as high conductivity up to the superconducting state, magnetic properties, catalytic activity of the processes of afterburning of exhaust gases, the high mobility in the oxygen sublattice and more.

  20. Biomass transition metal hydrogen-evolution electrocatalysts and electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Wei-Fu; Iyer, Shweta; Iyer, Shilpa; Sasaki, Kotaro; Muckerman, James T.; Fujita, Etsuko

    2017-02-28

    A catalytic composition from earth-abundant transition metal salts and biomass is disclosed. A calcined catalytic composition formed from soybean powder and ammonium molybdate is specifically exemplified herein. Methods for making the catalytic composition are disclosed as are electrodes for hydrogen evolution reactions comprising the catalytic composition.

  1. BIOCHEMICAL PARAMETERS OF LIPID METABOLISM IN ANIMALS AFFECTED BY HEAVY METAL SALTS AND TREATED WITH CARNITINE CHLORIDE AND SODIUM ALGINATE

    Directory of Open Access Journals (Sweden)

    I. R. Bekus

    2017-02-01

    Full Text Available Background. Lipid metabolism disorders in the organism affected by environmental pollutants, including poisoning with cadmium and lead salts are of topical matter nowadays. Objective. The study was aimed to examine biochemical features of lipid metabolism in rats subjected to toxic damage by lead and cadmium salts and treated with carnitine chloride and Algigel. Methods. Experiments were carried out on white mature outbred male rats weighing 180-200 g. To cause the toxic damage the animals were administered with aqueous solution of cadmium chloride and lead acetate daily for the period of 30 days using intra-gastric lavage. The indices of lipid metabolism were detected by biochemical methods. Results. In animals treated with cadmium chloride and lead acetate the following changes were observed: HDL-cholesterol concentrations significantly decreased, resulting in 87% of the levels in the intact animals on the third day, 84% on the fifth and 80% on the seventh day. Conversely, concentrations of HDL-cholesterol and VLDL-cholesterol significantly increased during the experiment. Respectively, the ratios for HDL-cholesterol are 240%, 352%, and 388%; and for VLDL-cholesterol 108%, 116%, and 132%. Conclusions. Lipids profile of the rats displayed changes in the levels of cholesterol, triglycerides and lipoproteins of low, high and very low density.

  2. Effect of water on metal-silicate partitioning and hydrogen incorporation in the core of the Earth and Mars

    Science.gov (United States)

    Clesi, Vincent; Bouhifd, Mohamed Ali; Bolfan-Casanova, Nathalie; Manthilake, Geeth; Andrault, Denis; Raepsaet, Caroline; Bureau, Hélène; Khodja, Hicham

    2017-04-01

    The accretion of planets from primordial materials and their subsequent differentiation to form a core and a mantle are fundamental questions in terrestrial and solar system. Many of the questions about the processes are still open and much debated. For example, could the presence of water during the metallic phase segregation affect the planet-accretion models? The existing studies on the elemental metal-silicate partitioning under hydrous conditions are limited to 1 GPa [5,6] well below the likely conditions prevailing during core formation on Earth and Mars. In the present study we use multi-anvil technique aver a range of P, T, fO_2 and water content (5 - 20 GPa, 2000 - 2500 K, from 1 to 5 log units below the iron-wüstite buffer, and for XH2O varying from 500 ppm to 1.5 wt.{%}). The present experimental results show that except for Fe, there is no effect of water on the partitioning of moderately siderophile elements. It allowed us to build consistent models of planetary accretion from reducing to oxidized conditions. Furthermore, for the range of water concentrations studied, there is no evidence of an important hydrogen incorporation into planetary cores, thus making unlikely for hydrogen to be a major light element of the core as previsously assumed [7]. [1] Morbidelli et al. (2000) Meteoritics & Planetary Science 1320, 1309-1320. [2] Marty (2012) EPSL 313-314, 56-66. [3] O'Brien et al. (2014) Icarus 239, 74-84. [4] Sarafian et al. (2014) Science 346, 623-626. [5] Righter and Drake (1999) EPSL 171, 383-399. [6] Jana and Walker (1999) GCA 63, 2299-2310. [7] Okuchi, T. (1997) Science 278, 1781-1784

  3. Application of patent bio-rack wetland system using Phragmites sp. for domestic wastewater treatment in the presence of high total dissolved solids (TDS) and heavy metal salts.

    Science.gov (United States)

    Valipour, Alireza; Raman, V Kalyan; Ghole, V S

    2011-07-01

    The quality of water recourses is degrading due to improper wastewater management. The aim of this study is to examine the potential of bio-rack system for treatment of domestic wastewater in the presence of high total dissolved solids (TDS) and heavy metal salts. The bio-rack is a modified wetland system incorporated with the advantages of phytoremediation and attached growth microbial process. The bio-rack is void of the soil strata based root zone system and in lieu a support matrix is provided to enrich the micro flora. The studies indicate that, Phragmites sp. can tolerate TDS up to 9000 mg/L in the bio-rack. The heavy metal removal is a function of phytoaccumulation or phytoextraction, which can lead to morphological deformity if heavy metals exceed the saturation limit of 786 and 5760 mg/kg Cd, 854 and 9280 mg/kg Cu, 639 and 4720 mg/kg Ni, 1187 and 7516 mg/kg Zn, in shoots and roots respectively. The reduction in TDS is marginal (14%) at the highest tolerable limit whereas the heavy metal reduction is 68%, 69%, 67%, 71% for Cd, Cu, Ni and Zn respectively at the outlet of the treatment system. The sewage treatment performance of the bio-rack system for all other parameters is estimated as 75 % Chemical Oxygen Demand (COD), 86 % Biological Oxygen Demand (BOD5), 27% Total Dissolved Solids (TDS), 73% Total Suspended Solids (TSS), 9% chlorides, 70% ammonia nitrogen (NH3-N), 32% phosphate (PO4-P), 92% most probable number (MPN) and 93% total viable count (TVC) reduction.

  4. comparative study with commercial rootstocks to determine the tolerance to heavy metal (Pb in the drought and salt stress tolerant eggplant breeding lines

    Directory of Open Access Journals (Sweden)

    Mevlüde Nur TOPAL

    2017-06-01

    Full Text Available Negative effects of heavy metals on plants are peroxidation of lipids in cell membranes, production of free oxygen radicals, disorders in photosynthesis, damages in DNAs and as a result death of the cell. Plant development, productivity and quality of the fruits are decreased in the plants that are exposed to Pb stress which is one of the most toxic heavy metals. Usage of rootstocks which is mainly used against biotic stress conditions also seems to be defined as a solution to abiotic stress conditions such as heavy metal stresses. In eggplant production, wild species and hybrids are used as rootstocks against soil based pathogens and nematode. Reactions of improvement lines derived from local gene resources for rootstock improvement to heavy metal stress which is one of the abiotic stresses were determined. While determining the resistance against Pb stress, commercially used eggplant rootstocks are compared. In this study 4 eggplant cultivars (S. melongena: Burdur Bucak, Mardin Kızıltepe, Artvin Hopa and Kemer whose resistance potential against salt and drought stresses had been previously revealed and 6 rootstocks of wild eggplant species or hybrids (AGR-703, Doyran, Hawk, Hikyaku, Köksal-F1 and Vista-306 were tested against Pb stress. Eggplant seedlings were applied to 0, 150 and 300 ppm Pb solutions (Pb(NO32 during 4-5 true leaf stage. 20 days after the stress application wet and dry weight of green parts and roots, height of the body part and leaf areas were measured. Pb tolerance of Köksal F1 and AGR703 rootstocks were higher than other commercial rootstocks. Mardin Kızıltepe and Burdur Merkez genotypes which have high tolerances against abiotic stress gave lower values with respect to Artvin Hopa and Kemer which are sensitive genotypes and many other rootstocks while comparing the reduction ratios of stress signs such as shoot fresh weight and shoot length according to control under Pb stress.

  5. Heavy metals, salts and organic residues in solid urban waste landfills and surface waters in their discharge areas: determinants for restoring their discharge areas: determinants for restoring their impact

    International Nuclear Information System (INIS)

    Hernandez, A. J.; Pastor, J.

    2009-01-01

    This report describes a continuous assessment of the impact of solid urban waste (SUW) landfills in the central Iberian Peninsula that were sealed with a layer of soil 20 years ago. cover soils and soils from discharge areas have been periodically analysed. Soil concentrations of salts and heavy metals affect the biotic components of these ecosystems. (Author)

  6. Extractive properties towards rare-earth metal ions of calix[4]arenes substituted at the narrow rim by phosphoryl and amide groups

    International Nuclear Information System (INIS)

    Yaftian, M.R.; Burgard, M.; Wieser, C.; Dieleman, C.B.; Matt, D.

    1998-01-01

    The extractive properties of the cone and partial-cone isomers of 5,11,17,23-tetra-tert-butyl-25,27-bis(diethylcarbamoylmethoxy)-26,28-bis (diphenylphosphinoylmethoxy)calix[4]arene (cone-1 and partial-cone-1) in 1,2-dichloroethane towards rare-earth metal ions in nitrate media at 25 C were investigated. The analysis of the extraction equilibrium obtained from a mixture of four rare-earths (La, Eu, Er and Y) revealed that the extracted species have a 1:1 metal/ligand ratio for both ligands. The intra-group separation efficiencies of the ligands have been evaluated in a competitive extraction process of 11 rare-earth metal ions (La, Pr, Nd, Sm, Eu, Gd, Dy, Ho, Er, Yb and Y). Significantly higher extractive properties were found for cone-1 with respect to partial-cone-1, suggesting the crucial role of the phosphoryl groups in the complexation of the rare-earth ions

  7. Production of chlorine from chloride salts

    Science.gov (United States)

    Rohrmann, Charles A.

    1981-01-01

    A process for converting chloride salts and sulfuric acid to sulfate salts and elemental chlorine is disclosed. A chloride salt and sulfuric acid are combined in a furnace where they react to produce a sulfate salt and hydrogen chloride. Hydrogen chloride from the furnace contacts a molten salt mixture containing an oxygen compound of vanadium, an alkali metal sulfate and an alkali metal pyrosulfate to recover elemental chlorine. In the absence of an oxygen-bearing gas during the contacting, the vanadium is reduced, but is regenerated to its active higher valence state by separately contacting the molten salt mixture with an oxygen-bearing gas.

  8. Effect of Solidification Rate and Rare Earth Metal Addition on the Microstructural Characteristics and Porosity Formation in A356 Alloy

    Directory of Open Access Journals (Sweden)

    M. G. Mahmoud

    2017-01-01

    Full Text Available The present study was performed on A356 alloy with the main aim of investigating the effects of La and Ce additions to 356 alloys (with and without 100 ppm Sr on the microstructure and porosity formation in these alloys. Measured amounts of La, Ce, and Sr were added to the molten alloy. The results showed that, in the absence of Sr, addition of La and Ce leads to an increase in the nucleation temperature of the α-Al dendritic network with a decrease in the temperature of the eutectic Si precipitation, resulting in increasing the freezing range. Addition of 100 ppm Sr results in neutralizing these effects. The presence of La or Ce in the casting has a minor effect on eutectic Si modification, in spite of the observed depression in the eutectic temperature. It should be noted that Ce is more effective than La as an alternate modifying agent. According to the atomic radius ratio, rLa/rSi is 1.604 and rCe/rSi is 1.559, theoretically, which shows that Ce is relatively more effective than La. The present findings confirm that Sr is the most dominating modification agent. Interaction between rare earth (RE metals and Sr would reduce the effectiveness of Sr. Although modification with Sr causes the formation of shrinkage porosity, it also reacts with RE-rich intermetallics, resulting in their fragmentation.

  9. New type of complex alkali and alkaline earth metal borates with isolated (B12O24)12) anionic group.

    Science.gov (United States)

    Wu, Hongping; Yu, Hongwei; Pan, Shilie; Jiao, Anqing; Han, Jian; Wu, Kui; Han, Shujuan; Li, Hongyi

    2014-03-28

    Compounds with isolated anionic groups often exhibit special linear and nonlinear optical properties and possess potential applications such as birefringence, second harmonic generation and stimulated Raman scattering crystals. In this paper, two new alkali and alkaline earth mixed-metal borates, Li3KB4O8 and LiNa2Sr8B12O24F6Cl, with isolated (B12O24)(12-) anionic groups have been successfully synthesized by spontaneous crystallization. Their structures were determined by single crystal X-ray diffraction and they both crystallize in the same space group, R3[combining macron]. More interestingly, further structure comparison shows that the discovered anhydrous borates with the (B12O24)(12-) groups also crystallize in the same space group R3[combining macron], which is related with the local symmetry of the (B12O24)(12-) groups. These structural features suggest that the crystal structures of the family of compounds depend more on their anionic groups. In addition, the property characterizations of the two new borates were investigated by TG-DSC, IR and UV-vis-NIR diffuse reflectance.

  10. Novel synergism by complex ligands in solvent extraction of rare earth metals(III) with β-diketones

    International Nuclear Information System (INIS)

    Imura, H.; Ebisawa, M.; Kato, M.; Ohashi, K.

    2006-01-01

    The extraction of rare earth metals(III) (RE) with hexafluoroacetylacetone (Hhfa) and 2-thenoyltrifluoroacetone (Htta) was studied in the presence of some cobalt(III) chelates such as tris(acetylacetonato)cobalt(III), tris(4-isopropyltropolonato)cobalt(III), tris(8-quinolinolato)cobalt(III), tris(8-quinolinethiolato)cobalt(III), and tris(diethyldithiocarbamato)cobalt(III) in benzene or toluene. The synergistic enhancement of the extraction of RE, especially of lanthanum(III) was found in all the systems. Therefore, those cobalt(III) chelates act as synergists or complex ligands. The equilibrium analysis and IR spectroscopic study were performed to evaluate the present synergistic mechanism. It was found that the RE-β-diketone chelates form 1:1 adducts, i.e., binuclear complexes, with the cobalt(III) chelates in the organic phase. The formation constants (β s,1 ) were determined and compared with those reported previously. The spectroscopic studies demonstrated that adducts have two different structures with inner- and outer-sphere coordination. In the former the cobalt(III) chelate directly coordinated to the RE ion and displaced the coordinated water molecules. In the latter the hydrogen-bonding was formed between the coordinating oxygen or sulfur atoms of cobalt(III) chelate and hydrogen atoms of the coordinated water molecules in the RE-β-diketone chelate. The types of the adducts are mainly due to the steric factors of the RE-β-diketone chelates and the cobalt(III) chelates

  11. A novel fluorescent probe (dtpa-bis(cytosine)) for detection of Eu(III) in rare earth metal ions

    Science.gov (United States)

    Yang, Fan; Ren, Peipei; Liu, Guanhong; Song, Youtao; Bu, Naishun; Wang, Jun

    2018-03-01

    In this paper, a novel fluorescent probe, dtpa-bis(cytosine), was designed and synthesized for detecting europium (Eu3 +) ion. Upon addition of Eu3 + ions into the dtpa-bis(cytosine) solution, the fluorescence intensity can strongly be enhanced. Conversely, adding other rare earth metal ions, such as Y3 +, Ce3 +, Pr3 +, Nd3 +, Sm3 +, Gd3 +, Tb3 +, Dy3 +, Ho3 +, Er3 +, Yb3 + and Lu3 +, into dtpa-bis(cytosine) solution, the fluorescence intensity is decreased slightly. Some parameters affecting the fluorescence intensity of dtpa-bis(cytosine) solution in the presence of Eu3 + ions were investigated, including solution pH value, Eu3 + ion concentration and interfering substances. The detection mechanism of Eu3 + ion using dtpa-bis(cytosine) as fluorescent probe was proposed. Under optimum conditions, the fluorescence emission intensities of EuIII-dtpa-bis(cytosine) at 375 nm in the concentration range of 0.50 × 10- 5 mol • L- 1-5.00 × 10- 5 mol • L- 1 of Eu3 + ion display a better linear relationship. The limit of detection (LOD) was determined as 8.65 × 10- 7 mol • L- 1 and the corresponding correlation coefficient (R2) of the linear equation is 0.9807. It is wished that the proposed method could be applied for sensitively and selectively detecting Eu3 + ion.

  12. Hydrogen storage property of alkali and alkaline-earth metal atoms decorated C24 fullerene: A DFT study

    Science.gov (United States)

    Zhang, Yafei; Cheng, Xinlu

    2018-04-01

    The hydrogen storage behavior of alkali and alkaline-earth metal (AM = Li, Na, K, Mg, Ca) atoms decorated C24 fullerene was investigated by using density functional theory (DFT) study. Our results indicate that the AM atoms prefer to adsorb atop the center of tetragon of C24 fullerene with the largest binding energy than other possible adsorption sites. Moreover, the hydrogen storage gravimetric density of 24H2/6Li/C24, 24H2/6Na/C24 and 36H2/6Ca/C24 configurations reaches up to 12.7 wt%, 10.1 wt% and 12 wt%, higher than the year 2020 target from the US department of energy (DOE). Also, the average adsorption energies of H2 molecules of the 24H2/6Li/C24, 24H2/6Na/C24 and 36H2/6Ca/C24 configurations are -0.198 eV/H2, -0.164 eV/H2 and -0.138 eV/H2, locate the desirable range under the physical adsorption at near ambient conditions. These findings will have important implications on designing new hydrogen storage materials in the future.

  13. Construction of double-stranded metallosupramolecular polymers with a controlled helicity by combination of salt bridges and metal coordination.

    Science.gov (United States)

    Ikeda, Masato; Tanaka, Yoshie; Hasegawa, Takashi; Furusho, Yoshio; Yashima, Eiji

    2006-05-31

    We describe the construction of the first double-stranded metallosupramolecular helical polymers. We designed and synthesized a supramolecular duplex comprised of complementary m-terphenyl-based strands bearing a chiral amidine or achiral carboxylic acid together with two pyridine groups at the four ends. Supramolecular polymerization of the duplex with cis-PtPh2(DMSO)2 in 1,1,2,2-tetrachloroethane produced the double-stranded metallosupramolecular polymer with a controlled helicity of which the two complementary metallostrands are intertwined through the amidinium-carboxylate salt bridges. The structures and hydrodynamic dimensions of the metallosupramolecular polymers were characterized by 1H NMR, diffusion-ordered NMR, dynamic light scattering, absorption, and CD measurements. The polymeric structure was also visualized by atomic force microscopy.

  14. Arynes, diaryliodonium salts and azine N-oxides in transition metal-free electrophilic N-arylation

    Science.gov (United States)

    Bugaenko, D. I.; Karchava, A. V.; Yurovskaya, M. A.

    2018-03-01

    The main approach to the synthesis of aromatic and heteroaromatic amines is based on palladium- and copper-catalyzed N-arylation reactions. Although these methods are highly efficient and provide extensive opportunities for the synthesis of (het)arylamines with various structures and properties, they have some limitations related to the catalysts used and reaction conditions. This review addresses alternative approaches to N-(het)arylation that have been extensively developed in the past decade and are based on the use of arynes, diaryliodonium salts and azine N-oxides as electrophilic (het)arylating agents. Because of mild reaction conditions and no need for catalysts and strong bases, these N-(het)arylation methods are attractive for various synthetic applications and open up new possibilities for the preparation of valuable organic compounds inaccessible via traditional catalytic methods. The attention is focussed on publications of the last decade. The bibliography includes 112 references.

  15. Reactive halogen species above salt lakes and salt pans

    OpenAIRE

    Holla, Robert

    2013-01-01

    Salt lakes can be found on all continents and saline soils cover 2.5% of the land surface of the earth (FAO, 2012). This thesis investigates the presence of reactive halogen species (RHS) above salt lakes and saline soils to evaluate their relevance for tropospheric chemistry of the planetary boundary layer. Ground-based MAX-DOAS and LP-DOAS measurements were conducted at salt lakes and two other sites with high halogen content. Prior to this work, RHS were found at three salt ...

  16. Extraction of metal ions in aqueous polyethylene glycol-inorganic salt two-phase systems in the presence of inorganic extractants: correlation between extraction behaviour and stability constants of extracted species.

    Science.gov (United States)

    Bulgariu, Laura; Bulgariu, Dumitru

    2008-07-04

    The use of aqueous polyethylene glycol-inorganic salt two-phase systems for the extraction of metal ions has a great potential due to their durability, non-toxicity and relative low cost. The aqueous phases can be easily separated by centrifugation, and the operation is possible in a range of experimental conditions. The experimental results have shown that for a given aqueous two-phase system, the extraction behaviour of metal ions in presence of inorganic extractants is mainly dependent on the stability of extracted species. In this paper we review our results obtained at metal ion extraction using inorganic extractants and discuss three major types of extraction behaviours.

  17. Thermolysis characteristics of salts of o-phthalic acid with the formation of Fe, Co, Ni, Cu metal particles

    Science.gov (United States)

    Yudanova, L. I.; Logvinenko, V. A.; Yudanov, N. F.; Rudina, N. A.; Ishchenko, A. V.; Korol'kov, I. V.; Semyannikov, P. P.; Sheludyakova, L. A.; Alferova, N. I.

    2016-06-01

    Studies of the thermolysis of ortho-[Ni(H2O)2(C8H4O4)](H2O)2, [Cu(H2O)(C8H4O4)], and acid [M(H2O)6](C8H5O4)2 (M(II) = Fe(II), Co(II), and Ni(II)), [Cu(H2O)2(C8H5O4)2] phthalates reveal that the solid products of their decomposition are composites with nanoparticles embedded in carbon-polymer matrices. Metallic nanoparticles with oxide nanoparticle impurities are detected in iron/cobalt polymer composites, while nickel/copper composites are composed of only metallic particles. It is found that nickel nanoparticles with the diameters of 6-8 nm are covered with disordered graphene layers, while the copperbased composite matrix contains spherical conglomerates (50-200 nm) with numerous spherical Cu particles (5-10 nm).

  18. Separation of rare earths and other valuable metals from deep-eutectic solvents: a new alternative for the recycling of used NdFeB magnets

    OpenAIRE

    Riano, Sofia; Petranikova, Martina; Onghena, Bieke; Vander Hoogerstraete, Tom; Banerjee, Dipanjan; Foreman, Mark R. St J.; ekberg, christian; BINNEMANS, Koen

    2017-01-01

    International audience; Deep-eutectic solvents (DESs) are used as a promising alternative to aqueous solutions for the recovery of valuable metals from NdFeB magnets. A deep-eutectic solvent based on choline chloride and lactic acid (molar ratio 1 : 2) was used for the leaching of rare earths and other metals from NdFeB magnets. A process for the separation of Fe, B and Co from Nd and Dy in the deep-eutectic solvent was developed by using the ionic liquid tricaprylmethylammonium thiocyanate (...

  19. Salts, sodium and heavy metals, in residual waters not purified, used for the watering in the cultivation of the sugar cane

    International Nuclear Information System (INIS)

    Mendez Romero, Franky Jose; Gisbert-Banquert, Juan Manuel

    2003-01-01

    In a farm located in the Valencia Lake Basin at northeast of Guacara city (Venezuelan country) and cultivated with sugar cane crop was evaluated during the period of July of 1996 to June of 1997 the salinity, sodicity and heavy metals concentration In municipal wastewater using to gravity Irrigated the sugar cane crop. The salinity was determinate by EC direct measure In Irrigation water (standardized at 25 Celsius degrade, Sodium by flame photometer Calcium and Magnesium by titulation with EDTA Cd, Cu, Fe Mn, Ni and Zn, were determinate by AAS before water samples preserve with NO 3 H. The wastewater quality employ to Irrigated the sugar cane crop was evaluated by mean of the Venezuelan official water Laws (1995) and compare too with the directives mentioned by Pratt and Suarez (1990), Crook and Bastian (1992) and the Mexican official wastewater irrigation laws NOM-CAA-032-ECOL/93 (1993. The results showed than the wastewater using to Irrigated the sugar cane field crop could to bring light and strong problems by salinity and sodium so much the soil as the crop The concentration of Cd, Fe and Cu are outside Limits proposals the Venezuelan official water laws (1995) Also when comparing the results with the other directives all the heavy metal concentration are outside the proposed Limits In each one of them except the Zn. In any case, the continuous use of the wastewater treated in this research could generate potential contamination and toxicity problems by heavy metals, salts and sodium In the crop, soils, groundwater and the people

  20. Effect of Rare Earth Elements (Er, Ho) on Semi-Metallic Materials (ScN) in an Applied Electric Field

    Science.gov (United States)

    Kim, Hyunjung; Park, Yeonjoon; King, Glen C.; Lee, Kunik; Choi, Sang H.

    2012-01-01

    The development of materials and fabrication technology for field-controlled spectrally active optics is essential for applications such as membrane optics, filters for LIDARs, windows for sensors, telescopes, spectroscopes, cameras and flat-panel displays. The dopants of rare earth elements, in a host of optical systems, create a number of absorption and emission band structures and can easily be incorporated into many high quality crystalline and amorphous hosts. In wide band-gap semiconductors like ScN, the existing deep levels can capture or emit the mobile charges, and can be ionized with the loss or capture of the carriers which are the fundamental basis of concept for smart optic materials. The band gap shrinkage or splitting with dopants supports the possibility of this concept. In the present work, a semi-metallic material (ScN) was doped with rare earth elements (Er, Ho) and tested under an applied electric field to characterize spectral and refractive index shifts by either Stark or Zeeman Effect. These effects can be verified using the UV-Vis spectroscopy, the Hall Effect measurement and the ellipsometric spectroscopy. The optical band gaps of ScN doped with Er and doped with Ho were experimentally estimated as 2.33eV and 2.24eV ( 0.2eV) respectively. This is less than that of undoped ScN (2.5 0.2eV). The red-shifted absorption onset is a direct evidence for the decrease of band gap energy (Eg), and the broadening of valence band states is attributable to the doping cases. A decrease in refractive index with an applied field was observed as a small shift in absorption coefficient using a variable angle spectroscopic ellipsometer. In the presence of an electric field, mobile carriers are redistributed within the space charge region (SCR) to produce this electro-refractive effect. The shift in refractive index is also affected by the density and location of deep potential wells within the SCR. In addition, the microstructure change was observed by a TEM

  1. Electrochemical transformations of oxygen and the defect structure of solid solutions on the basis of alkaline earth metal ortho-vanadates

    International Nuclear Information System (INIS)

    Khodos, M.Ya.; Belysheva, G.M.; Brajnina, Kh.Z.

    1986-01-01

    Effect of iso- and heterovalent substitution in the structure of alkaline earth metal ortho-vanadates and synthesis conditions, simulating the definite type of their crystal lattice disordering, on the character of potentiodynamic anodic-cathodic curves has been investigated by the method of cyclic voltammetry. Correlation between signals observed and the defect structure of oxide compounds is refined. Oxygen chemisorption is shown to be determined by concentration of nonequilibrium oxygen vacancies, which formation is accompanied by appearance of quasi-free electrons

  2. Association of alkali and alkaline earth metal cations with radical-anions of 9-fluorenone and 9.10-anthraquinone in dimethyl formamide medium

    International Nuclear Information System (INIS)

    Karpinets, A.P.; Bezuglyj, V.D.; Svetlichnaya, T.M.

    1988-01-01

    The polarographic method is used to estimate the stability of associates formed in dimethyl formamide by the products of one-electron reduction of 9-fluorenone and 9.10-anthraquinone with cations of alkali and alkali earth metals. It is shown that the strength of 9-fluorenone and 9.10-anthraquinone radical anion associates studied increases with cation charge increase and decrease of its crystallographic radius

  3. Fundamental Properties of Salts

    Energy Technology Data Exchange (ETDEWEB)

    Toni Y Gutknecht; Guy L Fredrickson

    2012-11-01

    Thermal properties of molten salt systems are of interest to electrorefining operations, pertaining to both the Fuel Cycle Research & Development Program (FCR&D) and Spent Fuel Treatment Mission, currently being pursued by the Department of Energy (DOE). The phase stability of molten salts in an electrorefiner may be adversely impacted by the build-up of fission products in the electrolyte. Potential situations that need to be avoided, during electrorefining operations, include (i) fissile elements build up in the salt that might approach the criticality limits specified for the vessel, (ii) electrolyte freezing at the operating temperature of the electrorefiner due to changes in the liquidus temperature, and (iii) phase separation (non-homogenous solution). The stability (and homogeneity) of the phases can be monitored by studying the thermal characteristics of the molten salts as a function of impurity concentration. Simulated salt compositions consisting of the selected rare earth and alkaline earth chlorides, with a eutectic mixture of LiCl-KCl as the carrier electrolyte, were studied to determine the melting points (thermal characteristics) using a Differential Scanning Calorimeter (DSC). The experimental data were used to model the liquidus temperature. On the basis of the this data, it became possible to predict a spent fuel treatment processing scenario under which electrorefining could no longer be performed as a result of increasing liquidus temperatures of the electrolyte.

  4. Novel 2D or 3D alkaline-earth metal sulfonate-phosphonates based on [O 3S-C 2H 4-PO 3H] 2- ligand

    Science.gov (United States)

    Du, Zi-Yi; Wen, He-Rui; Xie, Yong-Rong

    2008-11-01

    Three novel alkaline-earth metal sulfonate-phosphonates based on [O 3S-C 2H 4-PO 3H] 2- ligand, namely, [Ca(O 3SC 2H 4PO 3H)(H 2O) 2] ( 1), [Sr(O 3SC 2H 4PO 3H)] ( 2) and [Ba 2(O 3SC 2H 4PO 3H) 2] ( 3), have been synthesized by hydrothermal reactions. They represent the first structurally characterized alkaline-earth metal complexes of phosphonic acid attached with a sulfonate group. The structure of compound 1 features a 2D layer based on 1D chains of [Ca 2(PO 3) 2] bridged by -CH 2-CH 2-SO 3- groups. Compounds 2 and 3 show pillar-layer architecture based on two different inorganic layers linked by -CH 2-CH 2- groups. The inorganic layer in compound 2 features a 1D chain of edge-sharing SrO 8 polyhedra whereas that in compound 3 features an edge-sharing Ba 2O 14 di-polyhedral unit which is further corner-shared with four neighboring ones. The [O 3S-C 2H 4-PO 3H] 2- ligand shows diverse coordination modes in the three alkaline-earth metal sulfonate-phosphonates.

  5. Near-net-shape production of hollow titanium alloy components via electrochemical reduction of metal oxide precursors in molten salts

    OpenAIRE

    Hu, Di; Xiao, Wei; Chen, George Zheng

    2013-01-01

    Metal oxide precursors (ca. 90 wt pct Ti, 6 wt pct Al, and 4 wt pct V) were prepared with a hollow structure in various shapes such as a sphere, miniature golf club head, and cup using a one-step solid slip-casting process. The precursors were then electro-deoxidized in molten calcium chloride [3.2 V, 1173 K (900 C)] against a graphite anode. After 24 hours of electrolysis, the near-net-shape Ti-6Al-4V product maintained its original shape with controlled shrinkage. Oxygen contents in the Ti-...

  6. Pyro-Electrochemical Reduction of a Mixture of Rare Earth Oxides and NiO in LiCl molten Salt

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Min Woo; Jeong, Sang Mun [Department of Chemical Engineering, Chungbuk National University, Cheongju (Korea, Republic of)

    2017-06-15

    An electrochemical reduction of a mixture of NiO and rare earth oxides has been conducted to increase the reduction degree of rare earth oxides. Cyclic voltammetry (CV) measurement was carried out to determine the electrochemical reduction behavior of the mixed oxide in molten LiCl medium. Constant voltage electrolysis was performed with various supplied charges to understand the mechanism of electrochemical reduction of the mixed oxide as a working electrode. After completion of the electrochemical reduction, crystal structure of the reaction intermediates was characterized by using an X-ray diffraction method. The results clearly demonstrate that the rare earth oxide was converted to RE-Ni intermetallics via co-reduction with NiO.

  7. Removal of toxic and alkali/alkaline earth metals during co-thermal treatment of two types of MSWI fly ashes in China.

    Science.gov (United States)

    Yu, Jie; Qiao, Yu; Jin, Limei; Ma, Chuan; Paterson, Nigel; Sun, Lushi

    2015-12-01

    This study aims to vaporize heavy metals and alkali/alkaline earth metals from two different types of fly ashes by thermal treatment method. Fly ash from a fluidized bed incinerator (HK fly ash) was mixed with one from a grate incinerator (HS fly ash) in various proportions and thermally treated under different temperatures. The melting of HS fly ash was avoided when treated with HK fly ash. Alkali/alkaline earth metals in HS fly ash served as Cl-donors to promote the vaporization of heavy metals during thermal treatment. With temperature increasing from 800 to 900°C, significant amounts of Cl, Na and K were vaporized. Up to 1000°C in air, less than 3% of Cl and Na and less than 5% of K were retained in ash. Under all conditions, Cd can be vaporized effectively. The vaporization of Pb was mildly improved when treated with HS fly ash, while the effect became less pronounced above 900°C. Alkali/alkaline earth metals can promote Cu vaporization by forming copper chlorides. Comparatively, Zn vaporization was low and only slightly improved by HS fly ash. The low vaporization of Zn could be caused by the formation of Zn2SiO4, ZnFe2O4 and ZnAl2O4. Under all conditions, less than 20% of Cr was vaporized. In a reductive atmosphere, the vaporization of Cd and Pb were as high as that in oxidative atmosphere. However, the vaporization of Zn was accelerated and that of Cu was hindered because the formation of Zn2SiO4, ZnFe2O4 and ZnAl2O4 and copper chloride was depressed in reductive atmosphere. Copyright © 2015. Published by Elsevier Ltd.

  8. Near-Net-Shape Production of Hollow Titanium Alloy Components via Electrochemical Reduction of Metal Oxide Precursors in Molten Salts

    Science.gov (United States)

    Hu, Di; Xiao, Wei; Chen, George Z.

    2013-04-01

    Metal oxide precursors (ca. 90 wt pct Ti, 6 wt pct Al, and 4 wt pct V) were prepared with a hollow structure in various shapes such as a sphere, miniature golf club head, and cup using a one-step solid slip-casting process. The precursors were then electro-deoxidized in molten calcium chloride [3.2 V, 1173 K (900 °C)] against a graphite anode. After 24 hours of electrolysis, the near-net-shape Ti-6Al-4V product maintained its original shape with controlled shrinkage. Oxygen contents in the Ti-6Al-4V components were typically below 2000 ppm. The maximum compressive stress and modulus of electrolytic products obtained in this work were approximately 243 MPa and 14 GPa, respectively, matching with the requirement for medical implants. Further research directions are discussed for mechanical improvement of the products via densification during or after electrolysis. This simple, fast, and energy-efficient near-net-shape manufacturing method could allow titanium alloy components with desired geometries to be prepared directly from a mixture of metal oxides, promising an innovative technology for the low-cost production of titanium alloy components.

  9. Study of solubility of some metal cyclohexane carbonates

    International Nuclear Information System (INIS)

    Niyazov, A.N.; Amanov, K.B.; Trapeznikova, V.F.; Kul'maksimov, A.; Kolosova, N.

    1978-01-01

    The solubility of calcium, magnesium, strontium, barium, cabalt, copper and aluminium cyclohexane, carbonates (CHC) in water has been studied at 25 deg C. The salt solubility has been calculated according to the metal ion concentration in saturated solutions. It has been established, that the cobalt and rare earth cyclohexane carbonates are relatively very soluble in water and have solubility products of SP > 1x10 -5 . The solubility of CHC of multivalent metals increases with the decrease of pH values. Each salt has some ''limiting'' pH value of a solution, below which it decomposes completely and can not exist in a solution in the form of solid phase

  10. Salt and heavy metal tolerance and expression levels of candidate tolerance genes among four extremophile Cochlearia species with contrasting habitat preferences

    NARCIS (Netherlands)

    Nawaz, Ismat; Iqbal, Mazhar; Bliek, Mattijs; Schat, Henk

    2017-01-01

    To test the concept of a general “mineral stress tolerance”, we compared four extremophile Cochlearia species for salt (NaCl), zinc (Zn) and cadmium (Cd) tolerance and accumulation, and for expression of candidate tolerance genes for salt and Zn tolerance. Salt tolerance decreased in the order C.

  11. Report on the stakes of strategic metals: the case of rare earth metals. Report of the 8 March 2011 public audition and of the presentation of conclusion on the 21 June 2011

    International Nuclear Information System (INIS)

    Biraux, C.; Kert, Ch.

    2011-08-01

    The first part of this report proposes the content of a round table which gathered several experts in the field of rare earth metals (researchers, representatives of specialized branches companies like Saint-Gobain, Rhodia). The second part proposes the content of another round table which gathered experts who discussed the future of strategic metals like lithium, titanium or rhenium. Several issues are discussed: fundamental physics, physical and chemical properties, quantum physics, areas of interests (magnets, catalysis, ceramics, and photovoltaic arrays), availability, supplies and suppliers, processes, technological challenges and opportunities, and so on

  12. Synthesis of main group, rare-earth, and d{sup 0} metal complexes containing beta-hydrogen

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Ka King [Iowa State Univ., Ames, IA (United States)

    2013-01-01

    >F5)3 give the expected dicationic M{HB(C6F5)3}2L (M = Ca, Yb; L = THF2 or TMEDA) and dicationic mono(silylalkyl) LnC(SiHMe2)3{HB(C6F5)3}2 (Ln = Y, Lu, La), respectively. Salt metathesis reactions of Cp2(NR2)ZrX (X = Cl, I, OTf; R = t-Bu, SiHMe2) and lithium hydrosilazide ultimately afford hydride products Cp2(NR2)ZrH that suggest unusual β-hydrogen elimination processes. A likely intermediate in one of these reactions, Cp2Zr[N(SiHMe2)t-Bu][N(SiHMe2)2], is isolated under controlled synthetic conditions. Addition of alkali metal salts to this zirconium hydrosilazide compound produces the corresponding zirconium hydride. However as conditions are varied, a number of other pathways are also accessible, including C-H/Si-H dehydrocoupling, γ-abstraction of a CH, and β-abstraction of a SiH. Our observations suggest that the conversion of (hydrosilazido)zirconocene to zirconium hydride does not follow the classical four-center β- elimination mechanism.

  13. Origin of low sodium capacity in graphite and generally weak substrate binding of Na and Mg among alkali and alkaline earth metals.

    Science.gov (United States)

    Liu, Yuanyue; Merinov, Boris V; Goddard, William A

    2016-04-05

    It is well known that graphite has a low capacity for Na but a high capacity for other alkali metals. The growing interest in alternative cation batteries beyond Li makes it particularly important to elucidate the origin of this behavior, which is not well understood. In examining this question, we find a quite general phenomenon: among the alkali and alkaline earth metals, Na and Mg generally have the weakest chemical binding to a given substrate, compared with the other elements in the same column of the periodic table. We demonstrate this with quantum mechanics calculations for a wide range of substrate materials (not limited to C) covering a variety of structures and chemical compositions. The phenomenon arises from the competition between trends in the ionization energy and the ion-substrate coupling, down the columns of the periodic table. Consequently, the cathodic voltage for Na and Mg is expected to be lower than those for other metals in the same column. This generality provides a basis for analyzing the binding of alkali and alkaline earth metal atoms over a broad range of systems.

  14. Enhanced Electroresponse of Alkaline Earth Metal-Doped Silica/Titania Spheres by Synergetic Effect of Dispersion Stability and Dielectric Property.

    Science.gov (United States)

    Yoon, Chang-Min; Lee, Seungae; Cheong, Oug Jae; Jang, Jyongsik

    2015-09-02

    A series of alkaline earth metal-doped hollow SiO2/TiO2 spheres (EM-HST) are prepared as electrorheological (ER) materials via sonication-mediated etching method with various alkaline earth metal hydroxides as the etchant. The EM-HST spheres are assessed to determine how their hollow interior and metal-doping affects the ER activity. Both the dispersion stability and the dielectric properties of these materials are greatly enhanced by the proposed one-step etching method, which results in significant enhancement of ER activity. These improvements are attributed to increased particle mobility and interfacial polarization originating from the hollow nature of the EM-HST spheres and the effects of EM metal-doping. In particular, Ca-HST-based ER fluid exhibits ER performance which is 7.1-fold and 3.1-fold higher than those of nonhollow core/shell silica/titania (CS/ST) and undoped hollow silica/titania (HST)-based ER fluids, respectively. This study develops a versatile and simple approach to enhancing ER activity through synergetic effects arising from the combination of dispersion stability and the unique dielectric properties of hollow EM-HST spheres. In addition, the multigram scale production described in this experiment can be an excellent advantage for practical and commercial ER application.

  15. Reactivity of Heteropolytungstate and Heteropolymolybdate Metal Transition Salts in the Synthesis of Dimethyl Carbonate from Methanol and CO2

    Directory of Open Access Journals (Sweden)

    Amro Al-Amro

    2010-07-01

    Full Text Available A series of Keggin-type heteropoly compounds (HPC having different countercations (Co, Fe and different addenda atoms (W, Mo were synthesized and characterized by means of Fourier-Transform Infrared Spectrometer (FT-IR and X-ray powder diffraction (XRD. The catalytic properties of the prepared catalysts for the dimethyl carbonate (DMC synthesis from CO2 and CH3OH were investigated. The experimental results showed that the catalytic activity is significantly influenced by the type of the countercation and addenda atoms transition metal. Among the catalysts examined, Co1.5PW12O40 is the most active for the DMC synthesis, owing to the synergetic effect between Co and W. Investigating the effect of the support showed that the least acidic one (Al2O3 enhanced the conversion but decreased the DMC selectivity in favor of that of methyl formate (MF, while that of dimethoxy methane remained stable.

  16. Direct Analysis of Metal Ions in Solutions with High Salt Concentrations by Total Reflection X-ray Fluorescence.

    Science.gov (United States)

    Regadío, Mercedes; Riaño, Sofía; Binnemans, Koen; Vander Hoogerstraete, Tom

    2017-04-18

    Total reflection X-ray fluorescence (TXRF) is becoming more and more popular for elemental analysis in academia and industry. However, simplification of the procedures for analyzing samples with complex compositions and residual matrix effects is still needed. In this work, the effect of an inorganic (CaCl 2 ) and an organic (tetraalkylphosphonium chloride) matrix on metals quantification by TXRF was investigated for liquid samples. The samples were spiked with up to 20 metals at concentrations ranging from 3 to 50 mg L -1 per element, including elements with spectral peaks near the peaks of the matrix elements or near the Raleigh and Compton scattering peaks of the X-ray source (molybdenum anode). The recovery rate (RR) and the relative standard deviation (RSD) were calculated to express the accuracy and the precision of the measured element concentrations. In samples with no matrix effects, good RRs are obtained regardless of the internal standard selected. However, in samples with moderate matrix content, the use of an optimum internal standard (OIS) at a concentration close to that of the analyte significantly improved the quantitative analysis. In samples with high concentrations of inorganic ions, using a Triton X-100 aqueous solution to dilute the sample during the internal standardization resulted in better RRs and lower RSDs compared to using only water. In samples with a high concentration of organic material, pure ethanol gave slightly better results than when a Triton X-100-ethanol solution was used for dilution. Compared to previous methods reported in the literature, the new sample-preparation method gave better accuracy, precision, and sensitivity for the elements tested. Sample dilution with an OIS and the surfactant Triton X-100 (inorganic media) or ethanol (organic media) is recommended for fast routine elemental determination in matrix containing samples, as it does not require special equipment, experimentally derived case-dependent mathematical

  17. Functionalized paper--A readily accessible adsorbent for removal of dissolved heavy metal salts and nanoparticles from water.

    Science.gov (United States)

    Setyono, Daisy; Valiyaveettil, Suresh

    2016-01-25

    Paper, a readily available renewable resource, comprises of interwoven cellulosic fibers, which can be functionalized to develop interesting low-cost adsorbent material for water purification. In this study, polyethyleneimine (PEI)-functionalized paper was used for the removal of hazardous pollutants such as Au and Ag nanoparticles, Cr(VI) anions, Ni(2+), Cd(2+), and Cu(2+) cations from spiked water samples. Compared to untreated paper, the PEI-coated paper showed significant improvement in adsorption capacities toward the pollutants investigated in this study. Kinetics, isotherm models, pH, and desorption studies were carried out to study the adsorption mechanism of pollutants on the adsorbent surface. Adsorption of pollutants was better described by pseudo-second order kinetics and Langmuir isotherm model. Maximum adsorption of anionic pollutants was achieved at pH 5 while that of cations was at pH>6. Overall, the PEI-functionalized paper showed interesting Langmuir adsorption capacities for heavy metal ions such as Cr(VI) (68 mg/g), Ni(2+) (208 mg/g), Cd(2+) (370 mg/g), and Cu(2+) (435 mg/g) ions at neutral pH. In addition, the modified paper was also used to remove Ag-citrate (79 mg/g), Ag-PVP (46 mg/g), Au-citrate (30 mg/g), Au-PVP (17 mg/g) nanoparticles from water. Desorption of NPs from the adsorbent was done by washing with 2 M HCl or thiourea solution, while heavy metal ions were desorbed using 1 M NaOH or HNO3 solution. The modified paper retained its extraction efficiencies upon desorption of pollutants. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Transient compounds of high alkaline earth metals with custom-made organic ligands as potential precursors for the gas phase separator of high temperature ceramic superconductors

    International Nuclear Information System (INIS)

    Teske, M.

    1993-01-01

    The aim of this work was the representation of new transient custom-made metal/organic compounds of the high alkaline earth metals Ca, Sr and Ba as potential precursors for the gas phase separation (chemical vapour deposition, CVD) of high temperature ceramic superconductors. There is a report on the synthesis and comprehensive characterisation of representatives of the class of compounds of substituted metallocenes and the B diketone compounds of these metals. Some selected compounds were examined as regards their suitability for CVD. The main task was the examination of the effect of structural and electronic parameters of ligands on the properties of the compounds, where the volatility was to the fore. (orig./MM) [de

  19. Rare earth metals influence on mechanical properties and crack resistance of GP240GH and G17CrMo5-5 cast steels

    Directory of Open Access Journals (Sweden)

    M. Gajewski

    2009-10-01

    Full Text Available This paper presents results of research on modification influence of REM on mechanical properties and crack resistance of GP240GH cast carbon steel and G17CrMo5-5 high-temperature cast steel. The tests have been performed on successive industrial melts. The rare earth metals were put into the ladle during tapping of heat melt from the furnace. Each time ca 2000 kg of liquid metals were modified. Because of this the amount of sulphur in the cast steel was decreased and the non-metallic inclusion morphology was significantly changed. There were tested mechanical properties (Re,Rm, plastic properties (A5,Z and impact strength (KV, and on the basis of the three-point bend test the KJC stress intensity factor was evaluated. It was noticed that the REM modification brings essential increase of impact strength as well as fracture toughness determined by KJC factor.

  20. Isolation of transplutonium elements on ion exchangers from solutions of high salt concentration

    International Nuclear Information System (INIS)

    Guseva, L.I.; Tikhomirova, G.S.; Stepushkina, V.V.

    1985-01-01

    The behaviour of transplutonium elements (TPE) on cation and anion exchangers in aqueous alcoholic solutions of chlorides and nitrates of some alkali and alkaline earth metals depending on different factors: salt concentration, content of alcohol and of acid in the solution as well as the nature of a cation was studied. The data obtained were used to determine the optimal conditions of concentration of TPE on ion exchangers from solutions containing great quantities of salts. The advantages of the use of aqueous alcoholic solutions of nitric acid in the isolation of TPE are shown. (author)